Characterization and processing of heat treated aluminium matrix composite

Science.gov (United States)

Doifode, Yogesh; Kulkarni, S. G.

2018-05-01

The present study is carried out to determine density and porosity of Aluminium bagasse ash reinforced composite produced by powder metallurgy method. Bagasse ash is used as reinforcement material having high silica and alumina contents and varied from 5 weight % to 40 weight%. The manufactured composite is heat treated, the main objective of heat treatment is to prepare the material structurally and physically fit for engineering application. The results showed that the density decreases with percentage increase in reinforcement of bagasse ash from 2.6618 gm/cm3 to 1.9830 gm/cm3 with the minimum value at 40 weight% bagasse ash without heat treatment whereas after heat treatment density of composite increases due filling up of voids and porous holes. Heat treatment processing is the key to this improvement, with the T6 heat treated composite to convene the reduced porosity of composite. Consequently aluminium metal matrix composite combines the strength of the reinforcement to achieve a combination of desirable properties not available in any single material. It may observe that porosity in case of powder metallurgy samples showed more porosity portions compare to the casting samples. In order to achieve optimality in structure and properties of Bagasse ash-reinforcement heat treatment techniques have evolved. Generally, the ceramic reinforcements increase the density of the base alloy during fabrication of composites. However, the addition of lightweight reinforcements reduces the density of the hybrid composites. The results also showed that, the density varies from to with minimum value at 40 wt. % BA. The results of the statistical analysis showed that there are significant differences among the means of each property of the composites at various levels of BA replacement .It was concluded that bagasse ash can be used as reinforcement and the produced composites have low density and heat treatment reduces porosity which could be used in automobile industry for

Development of textile-reinforced carbon fibre aluminium composites manufactured with gas pressure infiltration methods

OpenAIRE

W. Hufenbach; M. Gude; A. Czulak; J. Śleziona; A. Dolata-Grosz; M. Dyzia

2009-01-01

Purpose: The aim of his paper is to show potential of textile-reinforced carbon fibre aluminium composite with advantage of the lightweight construction of structural components subjected to thermo-mechanical stress.Design/methodology/approach: The manufacture of specimens of the carbon fibre-reinforced aluminium was realised with the aid of an advanced differential gas pressure infiltration technique, which was developed at ILK, TU Dresden.Findings: The gas pressure infiltration technology e...

Corrosion behaviour of 2124 aluminium alloy-silicon carbide metal matrix composites in sodium chloride environment

International Nuclear Information System (INIS)

Singh, Nirbhay; Vadera, K.K.; Ramesh Kumar, A.V.; Singh, R.S.; Monga, S.S.; Mathur, G.N.

1999-01-01

Aluminium alloy based particle reinforced metal matrix composites (MMCs) are being considered for a range of applications. Their mechanical properties have been investigated in detail, but more information about their corrosion resistance is needed. In this investigation, the corrosion behaviour of silicon carbide particulates (SiC p )-2124 aluminium metal matrix composites was studied in 3 wt% sodium chloride solution by means of electrochemical technique and optical microscope. The effects of weight percentages and particle size of silicon carbide particulates on corrosion behaviour of the composite were studied in NaCl and it was observed that corrosion rate increases linearly with the increasing weight percentage of SiC p . The corrosion rate of the MMC increases by increasing the size of SiC particles. Anodization improved corrosion resistance of the composites. (author)

The Effects of Cocos Nucifera (Coconut Shell on the Mechanical and Tribological Properties of Recycled Waste Aluminium Can Composites

Directory of Open Access Journals (Sweden)

J.O. Agunsoye

2014-06-01

Full Text Available The dry sliding wear behaviour and mechanical properties of recycled aluminium metal matrix composite reinforced with 5 and 10 % coconut shell particles (CSp has been investigated. The particle size of Cocosnucifera (coconut shell that were used ranges from 50-300µm. The wear behaviors of developed samples were investigated under varied loads and speed using pin on disc equipment. The samples were also subjected to tensile, impact and hardness test. The result shows that the additions of coconut shell particles improved the wear resistance of the recycled aluminium can/CSp composites at low Speed (2.36 m/s. However, with increase in Speed (4.72 m/s, an increase in the specific wear rates were observed. Increasing the coconut shell particles additions to the recycled waste aluminium cans (RWAlC reduced the impact resistance, hence the toughness of the RWAlC/CSp composite samples. However, the impact resistance of the composites increased as the Cocosnucifera particle size increased. The result of the filler size variation shows that decrease in filler particles size improved the tensile strength and yield strength of the developed aluminium metal matrix /CSp composite. The hardness of the composite increased with increased additions of the filler within the matrix.

Vacuum brazing of aluminium metal matrix composite (55 vol.% SiC{sub p}/A356) using aluminium-based filler alloy

Energy Technology Data Exchange (ETDEWEB)

Niu, Jitai, E-mail: niujitai@163.com [Harbin Institute of Technology (China); Zhengzhou University (China); Luo, Xiangwei; Tian, Hao [Zhengzhou University (China); Brnic, Josip [University of Rijka (Croatia)

2012-11-20

Highlights: Black-Right-Pointing-Pointer The proper filler metal has been developed, especially for contents of Mg and Si. Black-Right-Pointing-Pointer The pressure device has been designed for specimen in vacuum brazing process. Black-Right-Pointing-Pointer The accurate measurement method for shear strength of lap joint has been found. Black-Right-Pointing-Pointer The brazing temperature of 560 Degree-Sign C has been optimised. Black-Right-Pointing-Pointer The micro-mechanism has been discussed for SiC{sub p}/Al composites' brazing joint. - Abstract: Aluminium matrix composites with high volume fractions of SiC particles, as the reinforcements, are potentially suitable materials for electronic packaging. These composites, due to their poor weldability, however, have very limited applications. The microstructure and shear strengths of the bonds made in 55 vol.% SiC{sub p}/A356 composite, using an aluminium based filler alloy containing Cu, Si, Mg and Ni, were investigated in this paper. The brazing temperature had a clear effect on the bond integrity, and the samples brazed at 560 Degree-Sign C demonstrated good bonding between the filler alloy and the SiC particles. The maximum shear strength achieved in this work was 102 MPa.

Process optimization in Nd:YAG laser microdrilling of alumina–aluminium interpenetrating phase composite

Directory of Open Access Journals (Sweden)

Ranjib Biswas

2015-07-01

Full Text Available In laser beam micromachining process, the quality of the drilled hole is of great importance. The quality of the microdrilled hole mainly depends on appropriate selection of process parameters. Predefined diameter of hole with minimum taper is of today's demand. The composite used for microdrilling operation is alumina–aluminium (Al2O3–Al interpenetrating phase composite (IPC, which is widely used in aircraft and space stations. Until date, no experimental study has been done to obtain microdrilled hole of desired diameter. In the present paper three hole qualities such as hole diameter at entry, at exit and hole taper have been optimized individually as well as simultaneously using a central composite design (CCD based on response surface methodology (RSM during pulsed Nd:YAG laser microdrilling operation on alumina–aluminium IPC sheet of 1.14 mm thickness. The analysis of variance (ANOVA test has also been done to identify the process parameters that contributed the most to get desired hole quality.

Aluminium-27 n.m.r. studies of aluminium fluoro complexes in dichloromethane solution: evidence for tetrafluoroaluminate anion

International Nuclear Information System (INIS)

Colton, R.; Eller, P.G.

1989-01-01

Mixed aluminium chloro/fluoro anions are formed in dichloromethane solution by the interaction of AlCl 3 and [Ph 3 PhCH 2 P] [H 2 F 3 ]. Aluminium-27 n.m.r. studies are restricted to the stoichiometric ranges F/Al from 1:1 to 3:1 and F/Al>8:1. Between these limits rapid precipitation reactions occur. In the fluoride-rich stoichiometric range there is rapid exchange on the n.m.r. time scale between the aluminium fluoro anion and free fluoride, so that a direct identification of the species by the multiplicity of the resonance is not possible. Indirect evidence strongly suggests that the aluminium species is [AlF 4 ] - . In the F/Al stoichiometry range from 1:1 to 3:1 aluminium-27 resonances were observed for all the other possible [AlCl χ F 4-χ ] - species. Studies on the aluminium iodo/fluoro system support the identification of [AlF 4 ] - , but the system is labile and the mixed iodo/fluoro species undergo rapid disproportionation. 12 refs., 1 fig

Characteristic evaluation of process parameters of friction stir welding of aluminium 2024 hybrid composites

Science.gov (United States)

Sadashiva, M.; Shivanand, H. K.; Vidyasagar, H. N.

2018-04-01

The Current work is aimed to investigate the effect of process parameters in friction stir welding of Aluminium 2024 base alloy and Aluminium 2024 matrix alloy reinforced with E Glass and Silicon Carbide reinforcements. The process involved a set of synthesis techniques incorporating stir casting methodology resulting in fabrication of the composite material. This composite material that is synthesized is then machined to obtain a plate of dimensions 100 mm * 50 mm * 6 mm. The plate is then friction stir welded at different set of parameters viz. the spindle speed of 600 rpm, 900 rpm and 1200 rpm and feed rate of 40 mm/min, 80 mm/min and 120 mm/min for analyzing the process capability. The study of the given set of parameters is predominantly important to understand the physics of the process that may lead to better properties of the joint, which is very much important in perspective to its use in advanced engineering applications, especially in aerospace domain that uses Aluminium 2024 alloy for wing and fuselage structures under tension.

Mechanical Properties of SiC, Al2O3 Reinforced Aluminium 6061-T6 Hybrid Matrix Composite

Science.gov (United States)

Murugan, S. Senthil; Jegan, V.; Velmurugan, M.

2018-04-01

This paper contains the investigation of tensile, compression and impact characterization of SiC, Al2O3 reinforced Aluminium 6061-T6 matrix hybrid composite. Hybrid matrix composite fabrication was done by stir casting method. An attempt has been made by keeping Al2O3 percentage (7%) constant and increasing SiC percentage (10, 15, and 20%). After fabricating, the samples were prepared and tested to find out the various mechanical properties like tensile, compressive, and impact strength of the developed composites of different weight % of silicon carbide and Alumina in Aluminium alloy. The main objective of the study is to compare the values obtained and choose the best composition of the hybrid matrix composite from the mechanical properties point of view.

Estimation of the mechanical properties of aluminium and an aluminium composite after equal channel angular pressing by means of the small punch test

Czech Academy of Sciences Publication Activity Database

Dobeš, Ferdinand; Dymáček, Petr; Besterci, M.

2015-01-01

Roč. 626, FEB (2015), s. 313-321 ISSN 0921-5093 R&D Projects: GA ČR(CZ) GAP108/12/1452; GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : Mechanical characterization * Aluminium alloys * Composites * Equal channel angular processing * Grain refinement Subject RIV: JI - Composite Materials Impact factor: 2.647, year: 2015

Appearance of anodised aluminium: Effect of alloy composition and prior surface finish

DEFF Research Database (Denmark)

Aggerbeck, Martin; Canulescu, Stela; Dirscherl, Kai

2014-01-01

Effect of alloy composition and prior surface finish on the optical appearance of the anodised layer on aluminium alloys was investigated. Four commercial alloys namely AA1050, Peraluman 706, AA5754, and AA6082 were used for the investigation. Microstructure and surface morphology of the substrat...

Composite Ni-Co-fly ash coatings on 5083 aluminium alloy

Energy Technology Data Exchange (ETDEWEB)

Panagopoulos, C.N., E-mail: chpanag@metal.ntua.gr [Laboratory of Physical Metallurgy, National Technical University of Athens, Zografos, 15780 Athens (Greece); Georgiou, E.P.; Tsopani, A.; Piperi, L. [Laboratory of Physical Metallurgy, National Technical University of Athens, Zografos, 15780 Athens (Greece)

2011-03-15

Ni-Co-fly ash coatings were deposited on zincate treated 5083 wrought aluminium alloy substrates with the aid of the electrodeposition technique. Structural and chemical characterization of the produced composite coatings was performed with the aid of X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron dispersive X-ray analysis (EDS) techniques. The Ni-Co-fly ash coatings were found to consist of a crystalline Ni-Co solid solution with dispersed fly ash particles. In addition, chemical analysis of the Ni-Co matrix showed that it consisted of 80 wt.% Ni and 20 wt.% Co. The co-deposition of fly ash particles leads to a significant increase of the microhardness of the coating. The corrosion behaviour of the Ni-Co-fly ash/zincate coated aluminium alloy, in a 0.3 M NaCl solution (pH = 3.5), was studied by means of potentiodynamic corrosion experiments.

Recent developments in advanced aircraft aluminium alloys

International Nuclear Information System (INIS)

Dursun, Tolga; Soutis, Costas

2014-01-01

Highlights: • To compete with composites, performance of aluminium alloys should be increased. • Al–Li alloys have higher strength, fracture and fatigue/corrosion resistance. • Improvements of aerospace Al alloys are due to optimised solute content and ratios. • In selecting new materials, there should be no reduction in the level of safety. • The use of hybrid materials could provide additional opportunities for Al alloys. - Abstract: Aluminium alloys have been the primary material for the structural parts of aircraft for more than 80 years because of their well known performance, well established design methods, manufacturing and reliable inspection techniques. Nearly for a decade composites have started to be used more widely in large commercial jet airliners for the fuselage, wing as well as other structural components in place of aluminium alloys due their high specific properties, reduced weight, fatigue performance and corrosion resistance. Although the increased use of composite materials reduced the role of aluminium up to some extent, high strength aluminium alloys remain important in airframe construction. Aluminium is a relatively low cost, light weight metal that can be heat treated and loaded to relatively high level of stresses, and it is one of the most easily produced of the high performance materials, which results in lower manufacturing and maintenance costs. There have been important recent advances in aluminium aircraft alloys that can effectively compete with modern composite materials. This study covers latest developments in enhanced mechanical properties of aluminium alloys, and high performance joining techniques. The mechanical properties on newly developed 2000, 7000 series aluminium alloys and new generation Al–Li alloys are compared with the traditional aluminium alloys. The advantages and disadvantages of the joining methods, laser beam welding and friction stir welding, are also discussed

Aluminium, gallium, indium and thallium

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

Aluminium can exist in a number of oxyhydroxide mineral phases including corundum, diaspore, boehmite and gibbsite. The stability constants at zero ionic strength reported for Al(OH) 3 (aq) vary linearly with respect to the inverse of absolute temperature. A full suite of thermodynamic parameters is available for all aluminium phases and hydrolysis species. Gallium hydrolyses to a greater extent than aluminium, with the onset of hydrolysis reactions occurring just above a pHof 1. In fact, even though aluminium has the smallest ionic radius of this series of metals, it has the weakest hydrolysis species and oxide/hydroxide phases.This is due to the presence of stabilising d-orbitals in the heavier metals, gallium, indium and thallium(III). There are few available data for the stability constants of indium(III) hydrolysis species. Of those that are available, the range in the proposed stability constants covers many orders of magnitude.

Oxidation behaviour of cast aluminium matrix composites with Ce surface coatings

International Nuclear Information System (INIS)

Pardo, A.; Merino, M.C.; Arrabal, R.; Feliu, S.; Viejo, F.

2007-01-01

The oxidation behaviour of SiC-reinforced aluminium matrix composites (A3xx.x/SiCp) has been studied after Ce-based treatments. Kinetics data of oxidation process were obtained from gravimetric tests performed at different temperatures (350, 425 and 500 o C). The nature of the oxidation layer was analyzed by scanning electron and atomic force microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy and X-ray diffraction. The extent of oxidation degradation in untreated composites was preferentially localized in matrix/SiCp interfaces favouring the MgO formation. Ce coatings favoured a uniform oxidation of the composite surface with MgAl 2 O 4 spinel formation. This oxide increased the surface hardness of the materials

Physical and chemical grounds of electrolytic fabrication of aluminium-strontium alloying composition

International Nuclear Information System (INIS)

Lysenko, A.P.

1998-01-01

It was revealed via study of literature sources that usage of alloying composition of strontium (not of sodium) is more expedient in modification of silumin-type alloys. In this case modification effect is keeping during long holdings and in repeated meltings. Electrolytic decomposition of strontium chloride with usage of liquid aluminium cathode is the most simple and cheap method for fabrication of alloying composition. The operation scheme for production of Al-Sr alloy was proposed in this work on the base of thermodynamic analysis

Investigation of aluminium-rich alloy system of aluminium-strontium-silicium

International Nuclear Information System (INIS)

Ganiev, I.N.; Vakhobov, A.B.; Dzhuraev, T.D.; Alidzhanov, F.N.

1976-01-01

An area of the solid solution based on aluminium was studied, and the surface was plotted of the liquidus adjoining the apex of the aluminium corner of the strontium-aluminium-silicon system. The investigation was carried out by microstructure and differential thermal analyses and by the measurement of the microhardness of the component phases. A combined solubility of silicon and strontium in aluminium was studied along three radial sections at Sr-to-Si ratios of 1/2, 1/1 and 2/1. The relationships of ''composition vs. Microhardness'', obtained in these sections, made it possible to define the boundaries of the phase regions in the aluminium corner of the strontium-aluminium-silicon system at 500 deg C. The greatest solubility is that along the Al-SrAl 2 Si 2 section at a Sr/Si ratio of 1/2. A further increase in the content of strontium brings about a drop in the solubility of silicon in solid aluminium. The projection of the liquidus surface of the strontium-aluminium-silicon system, rich in aluminium, includes four surfaces of primary crystallization: α-Al, SrAl 4 , SrAl 2 Si 2 and Si. The system comprises a section of Al-SrAl 2 Si 2 representing a quasibinary system of an eutectic type. The eutectic reaction takes place at a temperature of 640 deg C. The quasibinary Al-SrAl 2 Si 2 section divides the aluminium corner of the Sr-Al-Si system into two independent systems Al-SrAl 4 -SrAl 2 Si 2 and Al-Si-SrAl 2 Si 2 of an eutectic type

Studies of free field and confined explosions of aluminium enriched RDX compositions

Energy Technology Data Exchange (ETDEWEB)

Trzcinski, Waldemar A.; Cudzilo, Stanislaw; Paszula, Jozef [Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland)

2007-12-15

Research on the effect of aluminium contents and its particle size on free field and confined explosions characteristics of RDX-based compositions containing 15-60% aluminium was carried out. Parameters of blast waves produced by charges of the investigated explosives detonating in an open space were measured by the use of piezoelectric gauges. Simultaneously, photodiode set-ups were used to measure light output of the detonating charges. Quasi-static pressure measurements were conducted in steel chambers of 0.15 and 7 m{sup 3} volume filled with air. Moreover, the heat of detonation was measured with a calorimetric set in a 5.6 dm{sup 3} bomb filled with argon. The results of QSP and detonation heat measurements were compared with those obtained from thermochemical calculations. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Multi-objective Optimization of Friction Welding Process Parameters using Grey Relational Analysis for Joining Aluminium Metal Matrix Composite

Directory of Open Access Journals (Sweden)

Sreenivasan KONGANAPURAM SUNDARARAJAN

2018-05-01

Full Text Available Aluminium metal matrix composites has gained importance in recent time because of its improved mechanical and metallurgical properties. The welding of aluminium metal matrix composites using conventional welding process has got many demerits so in order to overcome them a solid state welding process is to be employed. To achieve a good strength weld in the aluminium metal matrix composite bars an efficient and most preferred technique is friction welding. In this work the aluminium metal matrix composite AA7075 + 10 % vol SiC-T6 is selected and friction welded. The combination of friction welding process parameters such as spindle speed, friction pressure, upset pressure and burn-off- length for joining the AA7075 + 10 % vol SiCP-T6 metal matrix composite bars are selected by Taguchi’s design of experiment. The optimum friction welding parameters were determined for achieving improved ultimate tensile strength and the hardness using grey relational analysis. A combined grey relational grade is found from the determined grey relational coefficient of the output responses and the optimum friction welding process parameters were obtained as spindle speed – 1200 rpm, friction pressure – 100 MPa, upset pressure – 250 MPa, Burn-off-Length – 2 mm. Analysis of variance (ANOVA performed shows that the friction pressure is the most significant friction welding parameter that influences the both the ultimate tensile strength and hardness of friction welded AA7075 + 10 % volSiCP-T6 joints. The fractured surface under microstructure study also revealed good compliance with the grey relational grade result. DOI: http://dx.doi.org/10.5755/j01.ms.24.2.17725

Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

Directory of Open Access Journals (Sweden)

B. Bobic

2010-03-01

Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

Aluminium/iron reinforced polyfurfuryl alcohol resin as advanced biocomposites

Directory of Open Access Journals (Sweden)

Rakesh Kumar

2016-07-01

Full Text Available Aluminium and iron are widely used in construction sectors for the preparation of advanced composites with epoxy resins as matrices. In recent times, there are several reports on the polymerization of polyfufuryl alcohol (PFA a thermoset bioresins from furfuryl alcohol (FA. FA is obtained from waste of sugarcane bagasse. In this work, first the possibility of curing PFA from FA in the presence of aluminium or iron has been explored. Absorbance results from colorimeter/spectrophotometerindicated that the curing of FA to PFA in presence of aluminium started easily while in presence of iron the curing of FA to PFA could not start. Based on the above results, aluminium wire reinforced composites were successfully prepared with three different weight fractions (0.13, 0.09 and 0.07 of aluminium wire. The mechanical properties of these composites were determined theoretically and reported.

Surface modification of 2014 aluminium alloy-Al2O3 particles composites by nickel electrochemical deposition

International Nuclear Information System (INIS)

Molina, J.M.; Saravanan, R.A.; Narciso, J.; Louis, E.

2004-01-01

A method to modify the surface of aluminium matrix composites (AMC) by electrochemical nickel deposition has been developed. Deposition was carried out in a stirred standard Watt's bath, whereas potential and time were varied to optimize coating characteristics. The method, that allowed to overcome the serious difficulties associated to electrochemical deposition of an inherently inhomogeneous material, was used to nickel coat composites of 2014 aluminium alloy-15 vol.% Al 2 O 3 particles. Coats with a good adherence and up to 60 μm thick were easily obtained. In order to improve surface properties, the coated composite was subjected to rather long (from 10 to 47.5 h) heat treatments at a temperature of 520 deg,C. The heat treatments improved the uniformity of the deposited layer and promoted the formation of Al-Ni intermetallics (mainly Al 3 Ni 2 , as revealed by X-ray diffraction and energy-dispersive X-ray analysis (EDX)). Experimental results indicate that growth of the intermetallic layer is diffusion limited

Evaluation of Mechanical Properties of MWCNT / Nanoclay Reinforced Aluminium alloy Metal Matrix Composite

Science.gov (United States)

Ratna Kumar, P. S. Samuel; Robinson Smart, D. S.; Alexis, S. John

2018-04-01

Aluminium alloy 5083 (AA5083) is a widely used material in aerospace, marine, defence and structural applications were mechanical and corrosion resistance property plays a vital role. For the present work, MWCNT / Nanoclay (montmorillonite (MMT) K10) mixed with AA5083 for different composition in weight percentage to enhance the mechanical property. Semi-solid state casting method (Compo-casting) was used to fabricate the composite materials. By using Field-emission scanning electron microscope (FESEM) the uniform dispersion of the reinforcement and microstructure were studied. Finally, the addition of Nanoclay shows decrease in tensile strength compared to the AA5083 / MWCNT composites and hardness value of the composites (AA5083 / MWCNT and AA5083 / Nanoclay) was found to increase significantly.

An Assessment of Mechanical and Tribological Property of Hybrid Aluminium Metal Matrix Composite

Directory of Open Access Journals (Sweden)

R. Santosh Kumar

2017-04-01

Full Text Available Composite materials has huge requirement in the area of automobile, aerospace, and wear resistant applications. This study presents the synthesis of composite reinforced with SiC and Al2O3 using gravity stir casting. Stir casting is the manufacturing process that is incorporated to produce the composite material because of its extreme bonding capacity with base material. The composition of reinforcement with 6061 aluminium matrix is SiC-7.5% and Al2O3 -2.5% respectively. The average size of reinforcement particle is 30-40 microns. The synthesised composite casting is machined using EDM to prepare specimens for various tests. Microstructure study was carried and the microstructure images prove the existence and dispersion of reinforcement particles in the metal matrix. There is no visible porosity is observed. The hardness of the specimen is tested using Vickers hardness tester and found considerable increase when compare with parent alloy Al 6061. Also mechanical and tribological properties of hybrid Aluminium metal matrix composite were employed. The fortifying material, Silicon Carbide is composed of tetrahedral of carbon and silicon atoms with strong bonds in crystal lattice along with its excellent wear resistance property and alumina have high strength and wear resistance. To avoid enormous material wastage and to achieve absolute accuracy, wire-cut EDM process is capitalised to engrave the specimen as per required dimensions. Three Tensile test specimens were prepared, in order to achieve reliability in results as per ASTM- E8 standard, and the values were tabulated. Impact test was carried out and the readings were tabulated. Wear test was carried out using pin on disc wear test apparatus and the results show considerable increase in wear resistant property when compare with parent alloy Al6061.The above work proves the successful fabrication of composite and evaluation of properties.

Derivation of a water quality guideline for aluminium in marine waters.

Science.gov (United States)

Golding, Lisa A; Angel, Brad M; Batley, Graeme E; Apte, Simon C; Krassoi, Rick; Doyle, Chris J

2015-01-01

Metal risk assessment of industrialized harbors and coastal marine waters requires the application of robust water quality guidelines to determine the likelihood of biological impacts. Currently there is no such guideline available for aluminium in marine waters. A water quality guideline of 24 µg total Al/L has been developed for aluminium in marine waters based on chronic 10% inhibition or effect concentrations (IC10 or EC10) and no-observed-effect concentrations (NOECs) from 11 species (2 literature values and 9 species tested including temperate and tropical species) representing 6 taxonomic groups. The 3 most sensitive species tested were a diatom Ceratoneis closterium (formerly Nitzschia closterium; IC10 = 18 µg Al/L, 72-h growth rate inhibition) aluminium forms of aluminate (Al(OH4 (-) ) and aluminium hydroxide (Al(OH)3 (0) ) although both dissolved, and particulate aluminium contributed to toxicity in the diatom Minutocellus polymorphus and green alga Dunaliella tertiolecta. In contrast, aluminium toxicity to the green flagellate alga Tetraselmis sp. was the result of particulate aluminium only. Four species, a brown macroalga (Hormosira banksii), sea urchin embryo (Heliocidaris tuberculata), and 2 juvenile fish species (Lates calcarifer and Acanthochromis polyacanthus), were not adversely affected at the highest test concentration used. © 2014 SETAC.

Mechanical properties of aluminium matrix composites reinforced with intermetallics

International Nuclear Information System (INIS)

Torres, B.; Garcia-Escorial, A.; Ibanez, J.; Lieblich, M.

2001-01-01

In this work 2124 aluminium matrix composites reinforced with Ni 3 Al, NiAl, MoSi 2 and Cr 3 Si intermetallic powder particles have been investigated. For comparison purposes, un reinforced 2124 and reinforced with SiC have also been studied. In all cases, the same powder metallurgy route was used, i. e. the 2124 alloy was obtained by rapid solidification and the intermetallic particles by self-propagating high-temperature synthesis (SHS). The matrix and the intermetallics were mechanically blended, cold compacted and finally hot extruded. Tensile tests were carried out in T1 and T4 treatments. Results indicate that mechanical properties depend strongly on the tendency to form new phases at the matrix-intermetallic interface during processing and/or further thermal treatments. The materials which present better properties are those that present less reaction between matrix and intermetallic reinforcement, i. e. MoSi 2 and SiC reinforced composites. (Author) 9 refs

Aspects of fabrication aluminium matrix heterophase composites by suspension method

Science.gov (United States)

Dolata, A. J.; Dyzia, M.

2012-05-01

Composites with an aluminium alloy matrix (AlMMC) exhibit several advantageous properties such as good strength, stiffness, low density, resistance and dimensional stability to elevated temperatures, good thermal expansion coefficient and particularly high resistance to friction wear. Therefore such composites are more and more used in modern engineering constructions. Composites reinforced with hard ceramic particles (Al2O3, SiC) are gradually being implemented into production in automotive or aircraft industries. Another application of AlMMC is in the electronics industry, where the dimensional stability and capacity to absorb and remove heat is used in radiators. However the main problems are still: a reduction of production costs, developing methods of composite material tests and final product quality assessment, standardisation, development of recycling and mechanical processing methods. AlMMC production technologies, based on liquid-phase methods, and the shaping of products by casting methods, belong to the cheapest production methods. Application of a suspension method for the production of composites with heterophase reinforcement may turn out to be a new material and technological solution. The article presents the material and technological aspects of the transfer procedures for the production of composite suspensions from laboratory scale to a semi-industrial scale.

Aspects of fabrication aluminium matrix heterophase composites by suspension method

International Nuclear Information System (INIS)

Dolata, A J; Dyzia, M

2012-01-01

Composites with an aluminium alloy matrix (AlMMC) exhibit several advantageous properties such as good strength, stiffness, low density, resistance and dimensional stability to elevated temperatures, good thermal expansion coefficient and particularly high resistance to friction wear. Therefore such composites are more and more used in modern engineering constructions. Composites reinforced with hard ceramic particles (Al 2 O 3 , SiC) are gradually being implemented into production in automotive or aircraft industries. Another application of AlMMC is in the electronics industry, where the dimensional stability and capacity to absorb and remove heat is used in radiators. However the main problems are still: a reduction of production costs, developing methods of composite material tests and final product quality assessment, standardisation, development of recycling and mechanical processing methods. AlMMC production technologies, based on liquid-phase methods, and the shaping of products by casting methods, belong to the cheapest production methods. Application of a suspension method for the production of composites with heterophase reinforcement may turn out to be a new material and technological solution. The article presents the material and technological aspects of the transfer procedures for the production of composite suspensions from laboratory scale to a semi-industrial scale.

Preparation and characterization of aluminium-silica metal matrix composite

Science.gov (United States)

Mallikarjuna, G. B.; Basavaraj, E.

2018-04-01

Aluminum alloys are widely used in aerospace and automobile industries due to their low density and good mechanical properties, better corrosion resistance and wear, low thermal coefficient of expansion as compared to conventional metals and alloys. The excellent properties of these materials and relatively low production cost make them a very attractive for a variety of applications. In this present work, Al alloy LM13-SiO2 composites were produced by stir casting method. The reinforcement SiO2 particle size used for preparation of composites are 106 µm, 150 µm, 250 µm and 355 µm with varying amount of 3 to 12 wt% in steps of 3. The prepared composite specimens were machined as per test standards. Effects of weight percentage of SiO2 particles on wear, tensile strength of Al alloy LM13-SiO2 composites have been investigated. The microstructures of the composites were studied to know the dispersion of the SiO2 particles in matrix. Experimental results shows that there is enhanced mechanical properties, when silica weighing 9% was added to the base aluminium alloy and also similar trend exists in all four different micron size of silica and also it has been observed that addition of SiO2 particles significantly improves wear resistance properties as compared with that of unreinforced matrix.

A Brief Research Review for Improvement Methods the Wettability between Ceramic Reinforcement Particulate and Aluminium Matrix Composites

Science.gov (United States)

Razzaq, Alaa Mohammed; Majid, Dayang Laila Abang Abdul; Ishak, M. R.; B, Uday M.

2017-05-01

The development of new methods for addition fine ceramic powders to Al aluminium alloy melts, which would lead to more uniform distribution and effective incorporation of the reinforcement particles into the aluminium matrix alloy. Recently the materials engineering research has moved to composite materials from monolithic, adapting to the global need for lightweight, low cost, quality, and high performance advanced materials. Among the different methods, stir casting is one of the simplest ways of making aluminium matrix composites. However, it suffers from poor distribution and combination of the reinforcement ceramic particles in the metal matrix. These problems become significantly effect to reduce reinforcement size, more agglomeration and tendency with less wettability for the ceramic particles in the melt process. Many researchers have carried out different studies on the wettability between the metal matrix and dispersion phase, which includes added wettability agents, fluxes, preheating the reinforcement particles, coating the reinforcement particles, and use composting techniques. The enhancement of wettability of ceramic particles by the molten matrix alloy and the reinforcement particles distribution improvement in the solidified matrix is the main objective for many studies that will be discussed in this paper.

Effect of friction time on the properties of friction welded YSZ‐alumina composite and 6061 aluminium alloy

Directory of Open Access Journals (Sweden)

Uday M. Basheer

2012-03-01

Full Text Available The aim of this work was to study the effect of friction time on the microstructure and mechanical properties of alumina 0, 25, 50 wt% yttria stabilized zirconia (YSZ composite and 6061 aluminium alloy joints formed by friction welding. The alumina-YSZ composites were prepared through slip casting in plaster of Paris molds (POP and subsequently sintered at 1600°C, while the aluminium rods were machined down using a lathe machine to the dimension required. The welding process was carried out under different rotational speeds and friction times, while friction force (0.5 ton-force was kept constant. Scanning electron microscopy was used to characterize the interface of the joints structure. The experimental results showed that the friction time has a significant effect on joint structure and mechanical properties.

Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste

Directory of Open Access Journals (Sweden)

L. Francis Xavier

2016-01-01

Full Text Available With an increase in the population and industrialization, a lot of valuable natural resources are depleted to prepare and manufacture products. However industrialization on the other hand has waste disposal issues, causing dust and environmental pollution. In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industrial waste obtained during processing of quarry rocks which are available in nature. In the composite materials design wear is a very important criterion requiring consideration which ensures the materials reliability in applications where they come in contact with the environment and other surfaces. Dry sliding wear test was carried out using pin-on-disc apparatus on the prepared composites. The results reveal that increasing the reinforcement content from 10 wt% to 20 wt% increases the resistance to wear rate.

The development and mechanical characterization of aluminium copper-carbon fiber metal matrix hybrid composite

Science.gov (United States)

Manzoor, M. U.; Feroze, M.; Ahmad, T.; Kamran, M.; Butt, M. T. Z.

2018-04-01

Metal matrix composites (MMCs) come under advanced materials that can be used for a wide range of industrial applications. MMCs contain a non-metallic reinforcement incorporated into a metallic matrix which can enhance properties over base metal alloys. Copper-Carbon fiber reinforced aluminium based hybrid composites were prepared by compo casting method. 4 weight % copper was used as alloying element with Al because of its precipitation hardened properties. Different weight compositions of composites were developed and characterized by mechanical testing. A significant improvement in tensile strength and micro hardness were found, before and after heat treatment of the composite. The SEM analysis of the fractured surfaces showed dispersed and embedded Carbon fibers within the network leading to the enhanced strength.

Toxicity of dissolved and precipitated aluminium to marine diatoms.

Science.gov (United States)

Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

2016-05-01

Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (paluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. Copyright © 2016 Elsevier B.V. All rights reserved.

The chemical transformation of copper in aluminium oxide during heating

International Nuclear Information System (INIS)

Wei, Y-L; Wang, H-C; Yang, Y-W; Lee, J-F

2004-01-01

Thermal treatment has recently been emerging as a promising environmental technology to stabilize heavy metal-containing industrial sludge. This study used x-ray absorption spectroscopy (XAS) to identify the species of copper contaminant contained in aluminium oxide that is one of the main compositions of sludge and soil. Results indicate that the originally loaded copper nitrate was transformed into Cu(OH) 2 after its dissolution in the aluminium oxide slurry. Extended x-ray absorption fine structure (EXAFS) fitting indicates that the main copper species in the 105 deg. C dried Cu(NO 3 ) 2 -loaded aluminium oxide is Cu(OH) 2 which accounts for ca. 75% of the loaded copper. After thermal treatment at 500 deg. C for 1 h, both x-ray absorption near-edge structure (XANES) and EXAFS fitting results show that CuO became the prevailing copper species (about 85%); the rest of the copper consisted of ∼ 15% Cu(OH) 2 and a negligible amount of Cu(NO 3 ) 2 . It was found that most Cu(OH) 2 and Cu(NO 3 ) 2 decomposed into CuO at 500 deg. C. Further increase of the heating temperature from 500 to 900 deg. C resulted in more decomposition of Cu(OH) 2 and Cu(NO 3 ) 2 ; therefore CuO remained as the main copper species. However, it was suggested that about 15% of the loaded copper formed CuAl 2 O 4 through the chemical reaction between CuO and Al 2 O 3 at 900 deg. C

Optimization of the composition and structure of heat-resistant casting aluminium alloys with additions of cerium, iron, nickel and zirconium

International Nuclear Information System (INIS)

Belov, N.A.; Lavrishchev, Yu.V.

2000-01-01

A study is made of the effect of composition and structure on mechanical properties of cast alloys of the Al-Ce-Ni-Fe-Zr system in which binary and ternary eutectics with participation of low alloyed aluminium solid solution and Al 4 Ce, Al 3 Ni and Al 9 FeNi phases are crystallized. It is found that microhardness of eutectics is heavily dependent on the volume fraction of aluminides and their dispersivity. It was shown that essential hardening of aluminium matrix can be achieved at the cost of zirconium additive in quantity of 0.6 % when using two-stage manufacturing operation. Experimental compositions of Al-10 % Ce-5% Ni-0.6 % Zr and Al-1.5 % Fe-1.5 % Ni-0.6 % Zr on the basis of ternary and binary eutectics respectively as billets essentially exceed industrial heat-resistant cast aluminium alloys AK12MMgN and AM5 as to a set of room and high-temperature mechanical properties and hot brittleness index [ru

Modelling of a cracked aluminium plate repaired with composite octagonal patch in mode I and mixed mode

International Nuclear Information System (INIS)

Ouinas, D.; Bachir Bouiadjra, B.; Achour, B.; Benderdouche, N.

2009-01-01

Adhesively bonded composite patch repair technique has been successfully applied in military aircraft repair and has recently been expanded to commercial aircraft industry. This technique is applied to extend the service life of cracked aluminium components. In this paper, the finite element method is applied to analyse the central crack's behaviour repaired by a boron/epoxy composite patch. The effects of the mechanical and geometrical properties of the patch on the variation of the stress intensity factor at the crack tip were highlighted. The obtained results show that the stress intensity factor at the crack tip, repaired by an octagonal patch of height 2c/3, is reduced by 5% with regard to the one repaired by an octagonal patch of size 'c'. For a height patch of c/3 the reduction is about 7%. The maximum reduction of composite patch of fibres in y-direction is about 30% compared to the aluminium patch. This reduction doubles when a composite patch of fibres in x-direction is used. The adhesive properties must be optimised to increase the performance of the repair of structures by such reinforcement

Processing and characterization of aluminium alloys or composites exhibiting low-temperature or high-rate superplasticity

International Nuclear Information System (INIS)

Huang, J. C.

1997-01-01

Wide applications of superplastic forming still face several problems, one is the high temperature that promotes grain growth, another is the low forming rate that makes economically inefficient. The current study is intended to develop a series of fabrication and thermomechanical processing, so as to result in materials possessing either low temperature superplasticity (LTSP) or high rate superplasticity (HRSP). The former has been achieved in the cast Al alloys, while the latter was accomplished in powder-metallurgy aluminium matrix composites. The aluminium alloys, after special thermomechanical processes, exhibited LTSP from 300 to 450 degree C with elongations varying from 300 to 700 %. The LTSP sheets after 700 % elongation at 350 degree C still possessed fine grains 3.7 μm size and narrow surface solute depletion zones 11 μm in with, resulting in a post-SP T6 strength of 500 MPa, significantly higher than that of the HTSP superplasticity alloys tested at 525 degree C or above. Meanwhile, it was found that LTSP materials may be transferred into HTSP materials simply by adding a preloading at 300-400 degree C for a small amount of work. As for the endeavor in making HRSP materials, 2024Al/SiC, 6061Al/SiC and Al/Al 3 Ti systems processed by powder metallurgy or mechanical alloying methods are under investigation. The average sizes of the reinforcing SiC or A13Ti particles, as well as the grain size are all around 1 μm. The aluminium composites have exhibited HRSP at 525-620 degree C and 10 -2 -10 -1 s -l , with elongations varying from 150 to 350 %. This ultimate goal is to produce an alloy or composite exhibiting low temperature and high strain rate superplasticity (LT and HRSP). (author)

Influence of tool pin in friction stir welding on activated carbon reinforced aluminium metal matrix composite

Science.gov (United States)

DijuSamuel, G.; Raja Dhas, J. Edwin

2017-10-01

This paper focus on impact of tool pin in friction stir welding on activated carbon reinforced aluminium metal matrix composite. For fabrication of metal matrix composite AA6061 is used as matrix and activated carbon is used as reinforcement and it is casted using modified stir casting technique. After casting metal matrix composite has undergone various microstructure tests like SEM,EDAX and XRD. FSW is carried out in this metal matrix composite by choosing various tool pin profile like square,round,Threaded round, hexagon and taper. The quality of welded plates is measured in terms of ultimate tensile strength and hardness.

Microstructure and hardness performance of AA6061 aluminium composite using friction stir processing

Science.gov (United States)

Marini, C. D.; Fatchurrohman, N.

2018-04-01

Rice husk ash (RHA) is an industrial waste that has become a potential reinforced material for aluminium matrix composite (AMCs) due to low cost and abundantly available resources. Friction stir processing (FSP) has been introduced as a method to modify surface properties of the metal and alloy including theirs composite as well. The present work reports the production and characterization of AA6061 and AA6061/5 vol% RHA using FSP using parameters rotation speed 1000 rpm and traversed speed 25 mm/min. The microstructure was studied using optical microscopy (OM). A homogenous dispersion of RHA particles was obtained in the composite. No agglomeration or segregation was observed. The produced composite exhibited a fine grain structure. An improvement in hardness profile was observed as AA6061/5 vol% RHA improves in hardness compared to FSPed of AA6061 without reinforcement.

The effects of stacking sequence and thermal cycling on the flexural properties of laminate composites of aluminium-epoxy/basalt-glass fibres

Science.gov (United States)

Abdollahi Azghan, Mehdi; Eslami-Farsani, Reza

2018-02-01

The current study aimed at investigating the effects of different stacking sequences and thermal cycling on the flexural properties of fibre metal laminates (FMLs). FMLs were composed of two aluminium alloy 2024-T3 sheets and epoxy polymer-matrix composites that have four layers of basalt and/or glass fibres with five different stacking sequences. For FML samples the thermal cycle time was about 6 min for temperature cycles from 25 °C to 115 °C. Flexural properties of samples evaluated after 55 thermal cycles and compared to non-exposed samples. Surface modification of aluminium performed by electrochemical treatment (anodizing) method and aluminium surfaces have been examined by scanning electron microscopy (SEM). Also, the flexural failure mechanisms investigated by the optical microscope study of fractured surfaces. SEM images indicated that the porosity of the aluminium surface increased after anodizing process. The findings of the present study showed that flexural modulus were maximum for basalt fibres based FML, minimum for glass fibres based FML while basalt/glass fibres based FML lies between them. Due to change in the failure mechanism of basalt/glass fibres based FMLs that have glass fibres at outer layer of the polymer composite, the flexural strength of this FML is lower than glass and basalt fibres based FML. After thermal cycling, due to the good thermal properties of basalt fibres, flexural properties of basalt fibres based FML structures decreased less than other composites.

Al2O3 - TiO2-A simple sol-gel strategy to the synthesis of low temperature sintered alumina-aluminium titanate composites through a core-shell approach

International Nuclear Information System (INIS)

Jayasankar, M.; Ananthakumar, S.; Mukundan, P.; Wunderlich, W.; Warrier, K.G.K.

2008-01-01

A simple sol-gel based core-shell approach for the synthesis of alumina-aluminium titanate composite is reported. Alumina is the core and titania is the shell. The coating of titania has been performed in aqueous medium on alumina particle by means of heterocoagulation of titanyl chloride. Further heat treatment results in low temperature formation of aluminium titanate as well as low temperature sintering of alumina-aluminium titanate composites. The lowering of the reaction temperature can be attributed to the maximisation of the contact surface between the reactants due to the core-shell approach involving nanoparticles. The mechanism of formation of aluminium titanate and the observations on densification features in the present process are compared with that of mixture of oxides under identical conditions. The sintered alumina-aluminium titanate composite has an average grain size of 2 μm. - Graphical abstract: The article presents a simple sol-gel process through core-shell approach to the synthesis of low temperature sintered alumina-aluminium titanate. The lowering of the reaction temperature can be attributed to the maximisation of the contact surface between the reactant due to the core-shell approach. This material showed the better microstructure control compared to the standard solid-state mixing route

The variations of aluminium species in mountainous forest soils and its implications to soil acidification.

Science.gov (United States)

Bradová, Monika; Tejnecký, Václav; Borůvka, Luboš; Němeček, Karel; Ash, Christopher; Šebek, Ondřej; Svoboda, Miroslav; Zenáhlíková, Jitka; Drábek, Ondřej

2015-11-01

Aluminium (Al) speciation is a characteristic that can be used as a tool for describing the soil acidification process. The question that was answered is how tree species (beech vs spruce) and type of soil horizon affect Al speciation. Our hypotesis is that spruce and beech forest vegetation are able to modify the chemical characteristics of organic horizon, hence the content of Al species. Moreover, these characteristics are seasonally dependent. To answer these questions, a detailed chromatographic speciation of Al in forest soils under contrasting tree species was performed. The Jizera Mountains area (Czech Republic) was chosen as a representative mountainous soil ecosystem. A basic forestry survey was performed on the investigated area. Soil and precipitation samples (throughfall, stemflow) were collected under both beech and spruce stands at monthly intervals from April to November during the years 2008-2011. Total aluminium content and Al speciation, pH, and dissolved organic carbon were determined in aqueous soil extracts and in precipitation samples. We found that the most important factors affecting the chemistry of soils, hence content of the Al species, are soil horizons and vegetation cover. pH strongly affects the amount of Al species under both forests. Fermentation (F) and humified (H) organic horizons contain a higher content of water extractable Al and Al(3+) compared to organo-mineral (A) and mineral horizons (B). With increasing soil profile depth, the amount of water extractable Al, Al(3+) and moisture decreases. The prevailing water-extractable species of Al in all studied soils and profiles under both spruce and beech forests were organically bound monovalent Al species. Distinct seasonal variations in organic and mineral soil horizons were found under both spruce and beech forests. Maximum concentrations of water-extractable Al and Al(3+) were determined in the summer, and the lowest in spring.

Steam Assisted Accelerated Growth of Oxide Layer on Aluminium Alloys

DEFF Research Database (Denmark)

Din, Rameez Ud; Yuksel, Serkan; Jellesen, Morten Stendahl

2013-01-01

Corrosion resistance of aluminium alloys is related to the composition and morphology of the oxide film on the surface of aluminium. In this paper we investigated the use of steam on the surface modification of aluminium to produce boehmite films. The study reveals a detailed investigation...... of the effect of vapour pressure, structure of intermetallic particles and thickness of boehmite films on the corrosion behaviour of aluminium alloys....

Wear and chemistry of zirconium-silicate, aluminium-silicate and zirconium-aluminium-silicate glasses in alkaline medium

International Nuclear Information System (INIS)

Rouse, C.G.; Lemos Guenaga, C.M. de

1984-01-01

A study of the chemical durability, in alkaline solutions, of zirconium silicate, aluminium silicate, zirconium/aluminium silicate glasses as a function of glass composition is carried out. The glasses were tested using standard DIN-52322 method, where the glass samples are prepared in small polished pieces and attacked for 3 hours in a 800 ml solution of 1N (NaOH + NA 2 CO 3 ) at 97 0 C. The results show that the presence of ZrO 2 in the glass composition increases its chemical durability to alkaline attack. Glasses of the aluminium/zirconium silicate series were melted with and without TiO 2 . It was shown experimentally that for this series of glasses, the presence of both TiO 2 and ZrO 2 gave better chemical durability results. However, the best overall results were obtained from the simpler zirconium silicate glasses, where it was possible to make glasses with higher values of ZrO 2 . (Author) [pt

Friction and corrosion resistance of sputter deposited supersaturated metastable aluminium-molybdenum alloys

Energy Technology Data Exchange (ETDEWEB)

Abu-Zeid, O.A. [Univ. of the United Arab Emirates, Al-Ain (United Arab Emirates). Dept. of Mech. Eng.; Bates, R.I. [Design, Mfg. and Marketing Research Inst., Univ. of Salford (United Kingdom)

1996-12-15

Two closed field unbalanced magnetrons with targets of aluminium and molybdenum have been used for the co-deposition of aluminium-molybdenum coatings with different compositions. A pin on disk machine and a computer controlled potentiostat have been used to evaluate respectively, the tribological and corrosion properties of the deposited alloys. Results have shown that introducing molybdenum into aluminium coatings improves their poor tribological properties. Aluminium-molybdenum coatings with different compositions have shown low wear behaviour and for coatings with high molybdenum contents (> 80%) friction coefficients against steel, as low as 0.18 have been obtained. The addition of molybdenum into aluminium coatings has reduced their corrosion tendency and corrosion current density in a marine environment. (orig.)

Wear behavior of carbon fiber/aluminium-composites during abrasive loading; Verschleissverhalten von Kohlenstoffaser/Aluminium-Verbunden unter abrasiver Beanspruchung

Energy Technology Data Exchange (ETDEWEB)

Wielage, B.; Dorner, A. [Technische Univ. Chemnitz (Germany). Lehrstuhl fuer Verbundwerkstoffe

1998-07-01

Abrasive wear resistance of aluminium is significantly improved by the reinforcement with a high volume percentage of carbon fibres. The wear of unreinforced aluminium after scratching by a diamond indenter can be described as pure microgrooving without any micro-chipping. After integration of 70 vol.-% carbon fibers the damage mechanism is considerably altered and a great amount of micro-chipping occurs. The abrasive wear is strongly influenced by the fiber orientation. The best wear resistance is observed when the fibers are orientated perpendicular to the wear surface. (orig.) [Deutsch] Die Verstaerkung von Aluminium mit einem hohen Volumengehalt endloser Kohlenstoffasern verbessert erkennbar dessen Resistenz gegenueber Abrasionsverschleiss. Der Verschleiss von unverstaerktem Aluminium infolge des Ritzens mit einem Diamantindenter erfolgt in Form von reinem Mikrofurchen ohne Spanbildung. Aufgrund der Integration von 70 Vol.-% Kohlenstoffasern wird eine erhebliche Zunahme des Schaedigungsmechanismus Mikrospanen festgestellt. Die Faserorientierung hat merklichen Einfluss auf die Sensibilitaet gegenueber Abrasion. Orientierung der anisotropen Kohlenstoffasern senkrecht zur Verschleissoberflaeche bedingt den geringsten Abrasionsverschleiss. (orig.)

Usage of neural network to predict aluminium oxide layer thickness.

Science.gov (United States)

Michal, Peter; Vagaská, Alena; Gombár, Miroslav; Kmec, Ján; Spišák, Emil; Kučerka, Daniel

2015-01-01

This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage) and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A · dm(-2) and 3 A · dm(-2) for creating aluminium oxide layer.

Usage of Neural Network to Predict Aluminium Oxide Layer Thickness

Directory of Open Access Journals (Sweden)

Peter Michal

2015-01-01

Full Text Available This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A·dm−2 and 3 A·dm−2 for creating aluminium oxide layer.

Effect of smelt aluminium on mechanical properties of steels

International Nuclear Information System (INIS)

Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

1987-01-01

Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

Scanning and transmission electron microscopy study of the microstructural changes occurring in aluminium matrix composites reinforced with SiC particles during casting and welding: interface reactions

Science.gov (United States)

Urena; Gomez De Salazar JM; Gil; Escalera; Baldonedo

1999-11-01

Processing of aluminium matrix composites (AMCs), especially those constituted by a reactive system such as Al-SiC, presents great difficulties which limit their potential applications. The interface reactivity between SiC and molten Al generates an aluminium carbide which degrades the composite properties. Scanning and transmission electron microscopes equipped with energy-dispersive X-ray spectroscopes are essential tools for determining the structure and chemistry of the Al-SiC interfaces in AMCs and changes occurring during casting and arc welding. In the present work, an aluminium-copper alloy (AA2014) reinforced with three different percentages of SiC particles was subjected to controlled remelting tests, at temperatures in the range 750-900 degrees C for 10 and 30 min. Arc welding tests using a tungsten intert gas with power inputs in the range 850-2000 W were also carried out. The results of these studies showed that during remelting there is preferential SiC particle consumption with formation of Al4C3 by interface reaction between the solid SiC particle and the molten aluminium matrix. The formation of Al4C3 by the same mechanism has also been detected in molten pools of arc welded composites. However, in this case there was formation of an almost continuous layer of Al4C3, which protects the particle against further consumption, and formation of aciculate aluminium carbide on the top weld. Both are formed by fusion and dissolution of the SiC in molten aluminium followed by reaction and precipitation of the Al4C3 during cooling.

Uranium (VI) chemistry at the interface solution/minerals (quartz and aluminium hydroxide): experiments and spectroscopic investigations of the uranyl surface species

International Nuclear Information System (INIS)

Froideval, A.

2004-09-01

This study deals with the understanding of the uranyl chemistry at the 0.1 M NaNO 3 solution/mineral (quartz and aluminium hydroxide) interface. The aims are:(i) to identify and to characterize the different uranyl surface species (mononuclear, polynuclear complexes and/or precipitates...), i.e. the coordination environments of sorbed/precipitated uranyl ions, by using X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS) and time-resolved laser-induced fluorescence spectroscopy (TRLFS), and;(ii) to investigate the influence of pH, initial uranyl aqueous concentration and hydroxyl ligand concentration on the uranyl surface speciation. Our study on the speciation of uranyl ions at the quartz surface (i) confirms the formation of uranyl polynuclear/oligomers on quartz from moderate (1 μmol/m 2 ) to high (26 μmol/m 2 ) uranyl surface concentrations and (ii) show that theses polynuclear species coexist with uranyl mononuclear surface species over a pH range ≅ 5-8.5 and a wide range of initial uranyl concentration o f the solutions (10-100 μM). The uranyl concentration of these surface species depends on pH and on the initial uranyl aqueous concentration. Hydrate (surface-) precipitates and/or adsorbed polynuclear species and monomeric uranyl surface complexes are formed on aluminium hydroxide. Uranyl mononuclear complexes are predominant at acidic pH, as well as uranyl in solution or on the surface. Besides mononuclear species, precipitates and/or adsorbed polynuclear species are predominantly formed at neutral pH values on aluminium hydroxide. A main contribution of our investigations is that precipitation and/or adsorption of polynuclear species seem to occur at low uranyl surface concentrations (0.01-0.4 μmol/m 2 ). The uranyl surface speciation is mainly dependent on the pH and the aluminol ligand concentration. (author)

Friction stir welding of Aluminium matrix composites – A Review

Directory of Open Access Journals (Sweden)

Subramanya Prabhu

2018-01-01

Full Text Available Friction stir welding (FSW is established as one of the prominent welding techniques to join aluminium matrix composites (AMCs. It is a solid state welding process, takes place well below the melting temperature of the material, eliminates the detrimental effects of conventional fusion welding process. Although the process is capable to join AMCs, challenges are still open that need to be fulfill to widen its applications. This paper gives the outline of the friction stir welding technique used to join AMCs. Effect of process variables on the microstructure and mechanical properties of the joints, behavior of reinforcing materials during welding, effect of tool profiles on the joint strength are discussed in detail. Few improvements and direction for future research are also proposed.

Investigation of planetary milling for nano-silicon carbide reinforced aluminium metal matrix composites

Energy Technology Data Exchange (ETDEWEB)

Kollo, Lauri, E-mail: lauri.kollo@staff.ttu.e [Laboratory of Advanced Materials Processing, EMPA, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Department of Materials Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn (Estonia); Leparoux, Marc; Bradbury, Christopher R.; Jaeggi, Christian [Laboratory of Advanced Materials Processing, EMPA, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Carreno-Morelli, Efrain; Rodriguez-Arbaizar, Mikel [University of Applied Sciences of Western Switzerland, Design and Materials Unit, 1950 Sion (Switzerland)

2010-01-21

High-energy planetary milling was used for mixing aluminium powders with 1 vol.% of silicon carbide (SiC) nanoparticles. A number of milling parameters were modified for constituting the relationship between the energy input from the balls and the hardness of the bulk nanocomposite materials. It was shown that mixing characteristics and reaction kinetics with stearic acid as process control agent can be estimated by normalised input energy from the milling bodies. For this, the additional parameter characterising the vial filling was determined experimentally. Depending on the ball size, a local minimum in filling parameter was found, laying at 25 or 42% filling of the vial volume for the balls with diameter of 10 and 20 mm, respectively. These regions should be avoided to achieve the highest milling efficiency.After a hot compaction, fourfold difference of hardness for different milling conditions was detected. Therewith the hardness of the Al-1 vol.% nanoSiC composite could be increased from 47 HV{sub 0.5} of pure aluminium to 163 HV{sub 0.5} when milling at the highest input energy levels.

EXPERIMENTAL INVESTIGATION ON TRIBOLOGICAL CHARACTERISTICS OF SILICON NITRIDE REINFORCED ALUMINIUM METAL MATRIX COMPOSITES

Directory of Open Access Journals (Sweden)

D. BHUVANESH

2017-05-01

Full Text Available Aluminium alloy (LM25 reinforced with silicon nitride was fabricated by liquid metallurgy route. The fabricated composite was investigated for dry sliding wear behaviour by conducting experiments using pin-on-disc tribometer. Set of experiments were planned using Taguchi’s technique and data analysis was carried out using L27 orthogonal array. Analysis of Variance (ANOVA technique was used to determine the significance of parameter with respect to wear rate. Signal-to-Noise ratio was employed to detect the most and least influential parameter as well as their level of influence. ‘Smaller the wear’ characteristic was chosen for the analysis of dry sliding wear. Results implied that, the load has the primary effect on the wear succeeded by the effect of sliding velocity and sliding distance. Scanning Electronic Microscopic studies were carried out on worn surfaces to understand the wear mechanism.Tribological results indicated that LM25 aluminium alloy could be better utilized as a material for piston, rotor and bearings for long life in low speed applications.

KS R41B. A high performance steel-aluminium composite material; KS R41B. Ein Stahl-Aluminium-Verbundwerkstoff fuer hohe Belastungen

Energy Technology Data Exchange (ETDEWEB)

Deicke, K. [KS Gleitlager GmbH (Germany). Bereich Metall; Matucha, H.; Schubert, W. [KS Gleitlager GmbH, St. Leon-Rot (Germany); Steffens, T. [KS Gleitlager GmbH, Neckarsulm (Germany)

2002-08-01

Aluminium-tin alloys have been well-known for a long time and have proved to be suitable bearing materials for crankshaft bearings for many years. The known alloy AlZn4,5SiCuPb is one of the aluminium materials capable of sustaining the highest mechanical loads. In order to achieve optimum sliding properties, it would be necessary to increase the share of the soft lead phase in the alloy. This article by KS Gleitlager GmbH shows a reasonably priced manufacturing technology for high-performance aluminium-zinc-silicon-copper alloys. (orig.) [German] Die Aluminium-Zinn-Lagerlegierungen sind seit langem bekannt und haben sich seit Jahren als Lagerwerkstoff fuer Kurbelwellenlager bewaehrt. Die Legierung AlZn4,5SiCuPb gehoert zu den mechanisch am hoechsten belastbaren Aluminium-Werkstoffen. Um optimale Gleiteigenschaften zu erzielen, muesste in der Legierung der Anteil des weichen Bleis noch weiter erhoeht werden. Dieser Beitrag der KS Gleitlager GmbH zeigt eine kostenguenstige Herstelltechnologie fuer hochbelastbare Aluminium-Zink-Silizium-Kupfer-Legierungen. (orig.)

Structural evolution in nanoporous anodic aluminium oxide

International Nuclear Information System (INIS)

Rocca, Emmanuel; Vantelon, Delphine; Reguer, Solenn; Mirambet, François

2012-01-01

Nanoporous and self-organized layers of aluminium alloys are used in many applications as membranes, templates for nanometric objects or corrosion protection for aluminium alloys. The use of this nanometric structure widely remains empirical, especially in the case of very small pores ( 4 into AlO 6 cluster and a partial release of sulphate ions are an important chemical transformation of the amorphous structure. This structural transformation defines the chemistry (pH and surface charge) inside the nanopores, the ageing behaviour and the possible incorporation or diffusion of chemical species in the nanostructure. Highlights: ► Investigations of local chemical environment of aluminium atoms in anodic aluminium oxide. ► The oxide structure is constituted by 2/3 of aluminium in tetrahedral coordination 1/3 in octahedral coordination. ► In contact with water, AlO 4 clusters are transformed into AlO 6 cluster and the aluminium sulphate bonds are hydrolysed. ► These transformations induce a pH decrease inside the nanostructure.

Aluminium production

International Nuclear Information System (INIS)

Winter, B.; Ayers, J.; Sammer, G.

2001-01-01

Aluminium is the most important non-ferrous metal by quantity. Aluminium is produced by electrolysis of aluminium oxide (also known as alumina). Alumina is produced by refining bauxite. The quantity of primary and secondary aluminium production in ECE-countries between 1992 and 1998 is shown. The European aluminium industry employs approximately 200 000 employees. The annual aluminium production in the European Union was 3.58 million tonnes in 1994, of which 44 % was secondary aluminium. In 1996 3.96 million tonnes of aluminium were produced in the EU, of which 44 % was secondary aluminium. (author)

Potentiometric titration curves of aluminium salt solutions and its ...

African Journals Online (AJOL)

Potentiometric titration curves of aluminium salt solutions and its species conversion ... of aluminium salt solutions under the moderate slow rate of base injection. ... silicate radical, and organic acid radical on the titration curves and its critical ...

Effect of aluminium particles on mechanical and morphological properties of epoxy nanocomposites

Directory of Open Access Journals (Sweden)

Bello Sefiu A.

2017-01-01

Full Text Available Bumper is a front or rear part of automobiles. It is designed and shaped to be impact absorbing and protecting automobiles from damage in low impact collisions. Initially, they were made from heavy steels, increasing the weight of automobiles and fuel consumption. Also, high impacts of steel bumpers on pedestrians during accidental collision cause fatalities and or disabilities. An effort to enhance fuel efficiency, safety, freedom of design and shape detailing, heavy alloys for automobile applications are now being replaced with polymeric composites. Aluminium micro particles and nanoparticles were prepared from aluminium cans through sand casting, lathe machine spinning, and ball milling techniques. Both types of aluminium particles were incorporated into a mixture of diglycidyl ether of bisphenol A (DGEBA, epoxy resin cured with amine base hardener (ABH. Phases of the epoxy polymer and composites were identified using Xray Diffraction (XRD. Spatial arrangement of the phases within the matrix and their elemental composition were examined using Scanning Electron Microscope with attached energy dispersive X-ray spectroscopy (SEM/EDX. Tensile, impact and micro hardness tests were conducted on the prepared epoxy/aluminium composites. Results of the XRD showed the presence of aluminium compounds/phases due to chemical reactions between aluminium particles and DGEBA/ABH system. SEM confirmed a homogeneous distribution of the phases within the epoxy matrix, and that there is a strong adhesion between the epoxy matrix and aluminium particles. Correlation between the mechanical properties of the prepared nanocomposite and the procured bumper materials exhibited a fair suitability of the prepared nanocomposites for automobile applications.

Electrochemical characteristics of a carbon fibre composite and the associated galvanic effects with aluminium alloys

Energy Technology Data Exchange (ETDEWEB)

Liu, Z., E-mail: zuojia.liu@gmail.com; Curioni, M.; Jamshidi, P.; Walker, A.; Prengnell, P.; Thompson, G.E.; Skeldon, P.

2014-09-30

Highlights: • Exposed carbon fibres on two defined regions (“front” and “side”) are a focus of the investigation in NaCl electrolyte. • The exposed carbon fibres on the side and front regions are responsible for a high cathodic current density. • The NaCl + CuSO{sub 4} electrolyte was used to investigate the cathodic polarization behaviour of the exposed carbon fibres. • Galvanic coupling behaviour between the composite and aluminium alloys (AA7075-T6 and AA1050) was measured in NaCl electrolyte. • The higher galvanic current density measured on AA1050 alloy introduced a higher dissolution rate than the AA7075-T6 alloy. - Abstract: The electrochemical behaviour of a carbon fibre reinforced epoxy matrix composite in 3.5% NaCl and 3.5% NaCl + 0.5 M CuSO{sub 4} electrolytes was examined by potentiodynamic polarisation, potentiostatic polarisation and scanning electron microscopy. Exposed carbon fibres on two defined regions (“front” and “side”) are a focus of the investigation. The large size of the exposed carbon fibres on the side region is responsible for a higher cathodic current density than the front region in the NaCl electrolyte. The deposition of copper on the front surface of composite confirmed that the significantly higher cathodic current resulted from the exposure of the fibres to the NaCl electrolyte. Galvanic coupling between the composite and individual aluminium alloys (AA7075-T6 and AA1050) was used to measure galvanic potentials and galvanic current densities. The highly alloyed AA7075-T6 alloy and its high population density of cathodic sites compared to the AA1050 acted to reduce the galvanic effect when coupled to the composite front or side regions.

Microstructure and Properties of Composite Coatings Obtained on Aluminium Alloys

Directory of Open Access Journals (Sweden)

Bara M.

2016-09-01

Full Text Available This paper presents methods of modifying the anode surface layers of Al2O3 by introducing carbon to their microstructure. Composite coatings were prepared using two different methods. In the first, coatings were formed by means of oxidation under constant current conditions. Anodic oxidation of aluminium was conducted in a multicomponent electrolyte with the addition of organic acids and graphite. The second method was based on the formation of oxide coatings in an electrolyte without the addition of graphite or heat treatment of the layers of succinic acid. The obtained coatings were tested using SEM, TEM, and GDOES (glow discharge optical emission spectrometry and their tribological and stereometric properties were measured. The study demonstrated the beneficial effects of the methods when used to improve the tribological properties of sliding couples.

Sinter aluminium as cladding material for fuel elements; Aluminium fritte comme materiau de gainage pour les elements combustibles

Energy Technology Data Exchange (ETDEWEB)

Mann, K E; Boudouresques, M B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Otto Fuchs, Meinerzhagen, Westfalen (Germany)

1961-07-01

1. Survey of the production process of sinter aluminium. 2. Description of the forming processes (extrusion, forging and rolling), whereby the production of tubing for atom piles will be explained in detail. 3. Production of ribbed tubes and tubes with close tolerances of sizes. 4. The different SAP-qualities and their properties under special consideration of the properties at elevated temperatures and the creep properties. 5. Diffusion behaviour of SAP with Be, Mg, Al, U and UO{sub 2}. 6. Corrosion behaviour in CO{sub 2} atmosphere at high temperature and in water. 7. Weldability. 8. Effect of irradiation on the mechanical properties. 9. Superiority of SAP compared with normal wrought alloys of the same composition. (author) [French] 1. Apercu des processus de production de l'aluminium fritte. 2. Expose des operations de transformation (filageries, forgeage et laminage), avec explication detaillee de la fabrication de gaine pour reacteurs. 3. Fabrication de tubes canneles et de tubes avec de faibles tolerances. 4. Diverses proprietes de l'aluminium fritte SAP, notamment proprietes aux temperatures elevees et proprietes de fluage. 5. Diffusion de l'aluminium fritte SAP en presence de Be, Mg, Al, U et UO{sub 2}. 6. Resistance a la corrosion dans une atmosphere de CO{sub 2} a temperature elevee et dans l'eau. 7. Possibilites de soudage. 8. Effet de l'irradiation sur les proprietes mecaniques. 9. Superiorite de l'aluminium fritte SAP sur les alliages forges normaux de meme composition. (auteur)

Characterisation of phase composition, microstructure and microhardness of electroless nickel composite coating co-deposited with SiC on casting aluminium LM24 alloy substrate

OpenAIRE

Franco, M.; Sha, Wei; Malinov, Savko

2013-01-01

Electroless Ni-P (EN) and composite Ni-P-SiC (ENC) coatings were developed on cast aluminium alloy, LM24. The coating phase composition, microstructure and microhardness were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and microhardness tester, respectively, on as-plated and heat-treated specimens. The original microstructure of the Ni-P matrix is not affected by the inclusion of the hard particles SiC. No formation of Ni-Si phase was observed upto 500°C of ...

Deformation features of aluminium in tensile tests

International Nuclear Information System (INIS)

Quadros, N.F. de.

1984-01-01

It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 400 0 C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.) [pt

Photochemical preparation of aluminium oxide layers via vacuum ultraviolet irradiation of a polymeric hexanoato aluminium complex

International Nuclear Information System (INIS)

Wennrich, L.; Khalil, H.; Bundesmann, C.; Decker, U.; Gerlach, J.W.; Helmstedt, U.; Manova, D.; Naumov, S.; Prager, L.

2013-01-01

By means of photochemical conversion of thin layers of a polymeric hexanoato aluminium complex as the precursor, thin aluminium oxide layers were prepared onto silicon wafers. The precursor compound was synthesized and characterized by several analytical techniques like NMR, FTIR, XPS, ICP, and found to be a polymeric aluminium-containing coordination compound which has been proposed to be a hydroxo-bridged aluminium chain with pendant hexanoyl side-chains ascertained as catena-poly[{di(κ-O,O-hexanoato)aluminium}(μ-hydroxo)] (PHAH). Thin layers deposited from a solution of PHAH in toluene onto silicon wafers were irradiated using VUV radiation from a xenon excimer lamp. The layers were characterized by XPS, XRD, XRR, and spectroscopic ellipsometry. VUV radiation with a radiant exposure of E = 36 J cm −2 led to almost carbon-free amorphous layers with a composition close to that of alumina having a density of about 2.1 g cm −3 . Thus, using the example of a polymeric aluminium complex, the potential of the photochemical conversion of metal complexes into oxides could be shown as an alternative method, in addition to sol–gel techniques, for the generation of thin plane metal-oxide layers at normal temperature and pressure. Highlights: ► A polymeric aluminium complex was synthesized and characterized by NMR, FTIR, XPS and ICP. ► Thin layers of the compound were irradiated using vacuum-UV radiation and converted to AlO x . ► Quantum-chemical calculations explain the conversion mechanism.

Three body abrasion of laser surface alloyed aluminium AA1200

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2012-06-01

Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4 kW Nd:YAG laser to improve the abrasion wear resistance. Aluminium surfaces reinforced with metal matrix composites and intermetallic phases were achieved. The phases present depended...

Phase composition and properties of rapidly cooled aluminium-zirconium-chromium alloys

International Nuclear Information System (INIS)

Sokolovskaya, E.M.; Badalova, L.M.; Podd''yakova, E.I.; Kazakova, E.F.; Loboda, T.P.; Gribanov, A.V.

1989-01-01

Using the methods of physicochemical analysis the interaction of aluminium with zirconium and chromium is studied. Polythermal cross sections between Al 3 -Zr-Al 7 Cr and radial polythermal cross section from aluminium-rich corner with the ratio of components Zr:Cr=5:7 by mass are constructed. The effect of zirconium and chromium content on electrochemical characteristics of aluminium-base rapidly quenching alloys in systems Al-Cr, Al-Zr, Al-Cr-Zr. An increase in chromium concentration in oversaturated solid solution of Al-Cr system expands considerably the range of passive state. When Al 7 Cr phase appears the range of passive stae vanishes

The effect of palm kernel shell ash on the mechanical properties of as-cast aluminium alloy matrix composites

Directory of Open Access Journals (Sweden)

Isiaka Oluwole OLADELE

2016-06-01

Full Text Available The present work describes the effect of palm kernel shell ash (PKSA as reinforcement on the mechanical properties of As-cast aluminium alloy. Recycled aluminium alloy from cylinder of an automotive engine block was degreased by using premium motor spirit (PMS also known as petrol, washed thoroughly with soap and water and sun dried for 5 days. The palm kernel shell was screened of dirt and other unwanted foreign materials before being roasted in furnace. The ash was further pulverized by laboratory ball mill machine followed by sieving to obtain particle sizes of 106 µm and divided into two parts. One portion was treated with NaOH solution while the other part was left as untreated before they are used to reinforced molten aluminium alloy in predetermined proportions. The newly developed composites were characterized with respect to their mechanical properties in response to the tests that were carried out on them. The results indicate that palm kernel shell ash can be used as potential reinforcing material for automobile applications.

Erosion resistance of composite materials on titanium, zirconium and aluminium nitride base under the electron beam effect

International Nuclear Information System (INIS)

Verkhoturov, A.D.; Kuzenkova, M.A.; Slutskin, M.G.; Kravchuk, L.A.

1977-01-01

Erosion resistance of composites based on nitrides of titanium, zirconium and aluminium to spark and electron beam processing has been studied. The erosion resistance in spark processing is shown to depend on specific electric resistance of the alloys. TiN-AlN and ZrN-AlN alloys containing more than 70% AlN (with specific electric resistance more than 10 6 -10 7 ohm/cm) caot be processed by spark method. It is shown that erosion of the composites by an electron beam depends primarily on the rate of evaporation of the components

Decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid

International Nuclear Information System (INIS)

Khomidi, A.K.; Mamatov, E.D.

2015-01-01

Present article is devoted to decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminium silicate ores were studied by means of X-ray phase, differential thermal and silicate analysis. The chemical composition of aluminium containing ores was determined. The optimal conditions of interaction of initial and pre calcined siallites with hydrochloric acid were defined. The kinetics of acid decomposition of aluminium silicate ores was studied as well.

Aluminium leaching from red mud by filamentous fungi.

Science.gov (United States)

Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

2015-11-01

This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. Copyright © 2015 Elsevier Inc. All rights reserved.

Structural and surface properties of highly ordered mesoporous magnesium-aluminium composite oxides derived from facile synthesis

Energy Technology Data Exchange (ETDEWEB)

Pan, Dahai, E-mail: pandahai@foxmail.com; Dong, Zhaoyang; He, Min; Chen, Wei; Chen, Shuwei; Yu, Feng; Fan, Binbin; Cui, Xingyu; Li, Ruifeng, E-mail: rfli@tyut.edu.cn

2017-01-15

Highly ordered mesoporous magnesium-aluminium composite oxides (denoted as OMMA-x) with a variety of n{sub Al}/n{sub Mg} ratios have been successfully synthesized via a facile strategy, and a salt effect was proposed to explain the formation mechanism. The incorporation of Mg can significantly improve the structural and surface properties of ordered mesoporous alumina (OMA) material. The resultant OMMA-x exhibited a much more ordered 2-D hexagonal mesostructure, a narrower pore size distribution, a higher specific surface area and pore volume, and a stronger basicity than those of OMA. More importantly, the highly homogeneous incorporation of Mg at the atomic level and the formation of framework Mg−O−Al bonds could effectively suppress the formation of crystalline alumina during the calcination process. As a result, OMMA-x demonstrated a superior thermal stability. For example, the ordered mesostructure of OMMA-8 could be well maintained with a high surface area of 182 m{sup 2}/g even after thermal treatment at 1000 °C. - Graphical abstract: A schematic procedure to illustrate the preparation of highly ordered mesoporous Mg-Al composite oxides (OMMA-x) with highly homogeneously dispersed Mg species and enhanced structural stability. - Highlights: • Mesoporous Mg-Al composite oxides with excellent structural and surface properties. • A highly homogeneous incorporation of Mg into the mesoporous framework of alumina. • A superior structural stability up to 1000 °C coupled with a large surface area. • A salt effect from the addition of Mg(NO{sub 3}){sub 2}·6H{sub 2}O to explain the formation mechanism.

Thermal properties of highly structured composite and aluminium sheets in an aerodynamic tunnel

Science.gov (United States)

Kulhavy, Petr; Egert, Josef

This article deals with the thermodynamic behaviour of heat shields - structured metal and composite plates. Experiments have been carried out in a wind tunnel with an additional heating, which simulates the heat source from engine or exhaust pipe and simultaneously the airflow generated during a car movement. The tested sheets with hexagonal structure were a standard commercial made of aluminium and a second manufactured by replication (lamination, diffusion) from glass fabric. The airflow in a parallel way along the sheets was analysed experimentally in order to determine the heat transfer efficiency between surfaces of sheets and surrounding airflow. The temperature on the sheets was chosen to observe the effects of different sheets material, various heat power and airflow velocity. During the experiment a thermal input below the sheets and airflow velocity through the tunnel have been changed. The thermal field distribution on the metal sheet is different than in case of composite sheet. For the composite material the thermal field distribution was more homogeneous. This article describe briefly also methods of obtaining real composite geometry based on scanned data and their reconstruction for using in some future numerical models.

Thermal properties of highly structured composite and aluminium sheets in an aerodynamic tunnel

Directory of Open Access Journals (Sweden)

Kulhavy Petr

2017-01-01

Full Text Available This article deals with the thermodynamic behaviour of heat shields - structured metal and composite plates. Experiments have been carried out in a wind tunnel with an additional heating, which simulates the heat source from engine or exhaust pipe and simultaneously the airflow generated during a car movement. The tested sheets with hexagonal structure were a standard commercial made of aluminium and a second manufactured by replication (lamination, diffusion from glass fabric. The airflow in a parallel way along the sheets was analysed experimentally in order to determine the heat transfer efficiency between surfaces of sheets and surrounding airflow. The temperature on the sheets was chosen to observe the effects of different sheets material, various heat power and airflow velocity. During the experiment a thermal input below the sheets and airflow velocity through the tunnel have been changed. The thermal field distribution on the metal sheet is different than in case of composite sheet. For the composite material the thermal field distribution was more homogeneous. This article describe briefly also methods of obtaining real composite geometry based on scanned data and their reconstruction for using in some future numerical models.

Effect of matrix constitution on interface of aluminium/δ-Al2O3 and strength of metal matrix composites

International Nuclear Information System (INIS)

Johansson, P.; Hutchinson, B.; Savage, S.J.

1992-06-01

Aluminium based fiber composites have been made by squeeze casting. The 'saffil' pre-forms used in the work employed aluminium oxide binder or silica binder. Two families of alloys have been used based either on high purity aluminium or 3% copper containing alloys. These were both alloyed with a range of magnesium contents from 0.1% to 5% with the aim of varying the degree of reaction and bonding between the matrix and the reinforcing fibres. Studies of macro- and micro structures have been performed as well as non-destructive testing by X-ray radiography. Tensile testing, three point bend tests on notched bars and wetting studies in a wetting balance are also included in the investigation. The structure of the squeeze cast products shows different zones. The extension and appearance of the zones are dependent on the alloy constitution. In general the surface of the casting have small equiaxed grains. This surface zone is replaced by a columnar grain zone which, in the center, transforms to an equiaxed crystal zone. Defects such as pores, fibre-free zones, and 'pockets' in the interface matrix/fiber have been found. Of these defects, only pores can be detected by X-ray radiography. Evaluation of tensile testing shows a relatively large scatter of results. The results reveal a dominant role of matrix composition on strength level. For the 20 vol% reinforced metals, with performs with silica binder, the maximum measured elongation was 3.5%. With alumina binder approximately half of the above mentioned ductility is obtained. The use of grain-refiner, Al-5Ti-B, decreases the ductility of the composite below 2%, independent of the type of binder. From 3-point bend tests fracture energies are estimated to vary between 0.3 and 0.6 Joule. The toughness is low. Studies of the wetting between pieces of ceramic pre-forms and molten Al-2Mg show that generally the wetting is poor. At the same time, the wettability of d-alumina with silicon oxide as binding medium was slightly

Investigation on Mechanical and Fatigue behaviour of Aluminium Based SiC/ZrO2 Particle Reinforced MMC

Science.gov (United States)

Ramesh, S.; Govindaraju, N.; Suryanarayan, C. P.

2018-04-01

The study is the work on Aluminium Metal Matrix Composites (MMC’s), which have wider applications in automobile, aerospace and defense industries, hi-tech engineering and power transmission due to their lightweight, high strength and other unique properties. The Aluminium Matrix Composites (AMC’s) refer to a kind of light weight high performance Aluminium centric material system. AMC’s consist of a non-metallic reinforcement which when included into aluminium matrix offers an advantage over the base material. Reinforcements like SiC, B4C, Al2O3, TiC, TiB2, TiO2 are normally preferred to improve mechanical properties of such composites. Here Aluminium 6061 is preferred as matrix material, while silicon carbide (SiC) and Zirconium di-oxide (ZrO2) is selected as reinforcement compounds. Conventional Stir casting procedure is employed to fabricate the necessary composites compositions, which are I. Al:SiC::100:5 and II. Al:ZrO2:SiC::100:3:2. Experimental results depict that the composition II provides higher hardness of 53.6 RHN as opposed to 45.8 RHN of composition I. In tensile strength composition II demonstrates 96.43 N/mm2 as opposed to 67.229 N/mm2 tensile strength of composition II. The fatigue test indicate a expected number of life cycles to failure of 105 cycles for composition II and over 104 cycles for composition I, at stress ranges of 79.062 MPa and 150.651 MPa respectively.

Study of Surface Roughness and Cutting force in machining for 6068 Aluminium alloy

Science.gov (United States)

Purushothaman, D.; Kaushik Yanamundra, Krishna; Krishnan, Gokul; Perisamy, C.

2018-04-01

Metal matrix composites, in particular, Aluminium Hybrid Composites are gaining increasing attention for applications in air and land because of their superior strength to weight ratio, density and high temperature resistance. Aluminium alloys are being used for a wide range of applications in Aerospace and Automobile industries, to name a few. The Aluminium Alloy 6068 has been used as the specimen. It is mainly composed of Aluminium (93.22 - 97.6 %), Magnesium (0.60 - 1.2 %), Silicon (0.60 - 1.4 %) and Bismuth (0.60 - 1.1 %). Aluminium 6068 is widely used for manufacturing aircraft structures, fuselages and wings. It is also extensively used in fabricating automobile parts such as wheel spacers. In this study, tests for the measurement of surface roughness and cutting force has been carried out on the specimen, the results evaluated and conclusions are drawn. Also the simulation of the same is carried out in a commercial FE software – ABAQUS.

Incorporation of transition metal ions and oxygen generation during anodizing of aluminium alloys

International Nuclear Information System (INIS)

Habazaki, H.; Konno, H.; Shimizu, K.; Nagata, S.; Skeldon, P.; Thompson, G.E.

2004-01-01

Enrichment of nickel at the alloy/film interface and incorporation of nickel species into the anodic film have been examined for a sputtering-deposited Al-1.2at.%Ni alloy in order to assist understanding of oxygen generation in barrier anodic alumina films. Anodizing of the alloy proceeds in two stages similarly to other dilute aluminium alloys, for example Al-Cr and Al-Cu alloys, where the Gibbs free energies per equivalent for formation of alloying element oxide exceeds the value for alumina. In the first stage, a nickel-free alumina film is formed, with nickel enriching in an alloy layer, 2 nm thick, immediately beneath the anodic oxide film. In the second stage, nickel atoms are oxidized together with aluminium, with oxygen generation forming gas bubbles within the anodic oxide film. This stage commences after accumulation of about 5.4 x 10 15 nickel atoms cm -2 in the enriched alloy layer. Oxygen generation also occurs when a thin layer of the alloy, containing about 2.0 x 10 19 nickel atoms m -2 , on electropolished aluminium, is completely anodized, contrasting with thin Al-Cr and Al-Cu alloy layers on electropolished aluminium, for which oxygen generation is essentially absent. A mechanism of oxygen generation, based on electron impurity levels of amorphous alumina and local oxide compositions, is discussed in order to explain the observations

Aluminium bridges, aluminium bridge decks

NARCIS (Netherlands)

Soetens, F.; Straalen, IJ.J. van

2003-01-01

Applications of aluminium have grown considerably in building and civil engineering the last decade. In building and civil engineering the increase of aluminium applications is due to various aspects like light weight, durability and maintenance, use of extrusions, and esthetics. The paper starts

High-temperature brazing of graphite using aluminium as brazing alloy

International Nuclear Information System (INIS)

Anikin, L.T.; Kravetskij, G.A.; Dergunova, V.S.

1977-01-01

The possibility of enhancing the strength of brazed joints, as well as the effect of the parameters of resistance heating of graphite VPP with PA-4 aluminium on the structure, composition and strength of the joint have been studied. It has been established that brazing of graphite materials, using an aluminium solder will produce a heat-resistant joint of a graphitic composition if the brazing temperature exceeds 2200 deg C. Thermocycling in the course of brazing results in a substantial (1.5-fold) increase in the strength of brazed joints

Aluminium effect on the physical properties of titanium

International Nuclear Information System (INIS)

Nazimov, O.P.; Il'in, A.A.; Zvonova, L.N.

1977-01-01

The effect of aluminium on the physical properties of titanium was investigated. Within the framework of the configuration model of matter it is shown that a change in physical properties with an aluminium content of up to 7.5 wt.% in alloys depends on the phase composition and electron structure. In interacting with titanium, aluminium exhibits acceptor properties, causing d→s electron transitions. The electrons which have shifted to the s-state are partly collectivized and partly localized into quasistable sp 3 configurations, with the resulting increase of the interatomic forces. An intensification of d→s transitions in alloying of titanium with aluminium stabilizes the α-phase. Predominance of d 1 configurations in the intermediate spectrum in the region of the α-solution increases the ratio of the axes of the HCP lattice and determines the electron type of conduction of alloys of the Ti-Al system

Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

Directory of Open Access Journals (Sweden)

Iban Vicario

2016-01-01

Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

Uranium (VI) chemistry at the interface solution/minerals (quartz and aluminium hydroxide): experiments and spectroscopic investigations of the uranyl surface species; Chimie de l'uranium (VI) a l'interface solution/mineraux (quartz et hydroxyde d'aluminium): experiences et caracterisations spectroscopiques

Energy Technology Data Exchange (ETDEWEB)

Froideval, A.

2004-09-15

This study deals with the understanding of the uranyl chemistry at the 0.1 M NaNO{sub 3} solution/mineral (quartz and aluminium hydroxide) interface. The aims are:(i) to identify and to characterize the different uranyl surface species (mononuclear, polynuclear complexes and/or precipitates...), i.e. the coordination environments of sorbed/precipitated uranyl ions, by using X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS) and time-resolved laser-induced fluorescence spectroscopy (TRLFS), and;(ii) to investigate the influence of pH, initial uranyl aqueous concentration and hydroxyl ligand concentration on the uranyl surface speciation. Our study on the speciation of uranyl ions at the quartz surface (i) confirms the formation of uranyl polynuclear/oligomers on quartz from moderate (1 {mu}mol/m{sup 2}) to high (26 {mu}mol/m{sup 2}) uranyl surface concentrations and (ii) show that theses polynuclear species coexist with uranyl mononuclear surface species over a pH range {approx_equal} 5-8.5 and a wide range of initial uranyl concentration o f the solutions (10-100 {mu}M). The uranyl concentration of these surface species depends on pH and on the initial uranyl aqueous concentration. Hydrate (surface-) precipitates and/or adsorbed polynuclear species and monomeric uranyl surface complexes are formed on aluminium hydroxide. Uranyl mononuclear complexes are predominant at acidic pH, as well as uranyl in solution or on the surface. Besides mononuclear species, precipitates and/or adsorbed polynuclear species are predominantly formed at neutral pH values on aluminium hydroxide. A main contribution of our investigations is that precipitation and/or adsorption of polynuclear species seem to occur at low uranyl surface concentrations (0.01-0.4 {mu}mol/m{sup 2}). The uranyl surface speciation is mainly dependent on the pH and the aluminol ligand concentration. (author)

Bioactive type glass-ceramics within incorporated aluminium

International Nuclear Information System (INIS)

Volzone, C.; Stabile, F.M.; Ortiga, J.

2012-01-01

Bioactive glass-ceramics are used as biomaterials for the reparation of bone tissue. They are prepared, generally, by bioglass of specific composition for each particular use. The aluminium addition in the formulation at very small quantities influences on the structural properties. Two glass-ceramics obtained by P 2 O 5 -Na 2 O-CaO-SiO 2 formulation within aluminium (0.5 % in Al 2 O 3 base) added through a reactive alumina and purified feldspar were analyzed. The results showed structural differences between both glass-ceramics. (author)

Fabrication and characterization of aluminium hybrid composites reinforced with fly ash and silicon carbide through powder metallurgy

Science.gov (United States)

Bilal Naim Shaikh, Mohd; Arif, Sajjad; Arif Siddiqui, M.

2018-04-01

This paper reports the fabrication and characterization of aluminium hybrid composites (AMCs) reinforced with commonly available and inexpensive fly ash (FA, 0, 5, 10 and 15 wt.%) particles along silicon carbide (SiC) using powder metallurgy process. Scanning electron microscopy (SEM) and x-ray diffraction (XRD) were employed for microstructural characterization and phase identification respectively. Wear behaviour were investigated using pin-on-disc wear tester for the different combinations of wear parameters like load (10, 20 and 30 N), sliding speed (1.5, 2 and 2.5 m s‑1) and sliding distance (300, 600 and 900 m). SEM confirms the uniform distribution of FA and SiC in aluminium matrix. The hardness of Al/SiC/FA is increased by 20%–25% while wear rate decreased by 15%–40%. From wear analysis, sliding distance was the least significant parameter influencing the wear loss followed by applied load and sliding speed. To identify the mechanism of wear, worn out surface were also analysed by SEM.

The effects of composition and firing cycle on sintering of aluminium nitride

International Nuclear Information System (INIS)

Hewett, C.; Trigg, M.B.

1992-01-01

A central composite design was used to evaluate the relative effects of temperature, time and Y 2 O 3 content on the densification behaviour of a commercial aluminium nitride (AIN). Over the range of the independent variables studied, temperature was found to exert the dominate influence. Low levels of Y 2 O 3 were found to be effective for the densification of AIN. After firing, cubic 3Y 2 O 3.5 Al 2O3 (YAG) was detected for the lower levels of Y 2 O 3 addition. At the higher levels both YAG and 2Y 2 O 3 .Al 2 O 3 were detected. For a dense sample the values obtained for hardness and fracture toughness were comparable to those reported in the literature. 11 refs., 1 tab

Investigation and in situ removal of spatter generated during laser ablation of aluminium composites

International Nuclear Information System (INIS)

Popescu, A.C.; Delval, C.; Shadman, S.; Leparoux, M.

2016-01-01

Highlights: • Study of spatter generated during laser irradiation of an aluminium nanocomposite. • Number of droplets was 1.5–3 times higher for laser in depth vs surface focused beams. • High speed imaging revealed particles exploding in flight similar to a fireworks effect. • Three methods were selected for droplets removal in situ and the results are analyzed. - Abstract: Spatter generated during laser irradiation of an aluminium alloy nanocomposite (AlMg5 reinforced with Al_2O_3 nanoparticles) was monitored by high speed imaging. Droplets trajectory and speed were assessed by computerized image analysis. The effects of laser peak power and laser focusing on the plume expansion and expulsed droplet speeds were studied in air or under argon flow. It was found that the velocity of visible droplets expulsed laterally or at the end of the plume emission from the metal surface was not dependent on the plasma plume speed. The neighbouring area of irradiation sites was studied by optical and scanning electron microscopy. Droplets deposited on the surface were classified according to their size and counted using a digital image processing software. It was observed that the number of droplets on surface was 1.5–3 times higher when the laser beam was focused in depth as compared to focused beams, even though the populations average diameter were comparable. Three methods were selected for removing droplets in situ, during plume expansion: an argon gas jet crossing the plasma plume, a fused silica plate collector transparent to the laser wavelength placed parallel to the irradiated surface and a mask placed onto the aluminium composite surface. The argon gas jet was efficient only for low power irradiation conditions, the fused silica plate failed in all tested conditions and the mask was successful for all irradiation regimes.

Alloys of uranium and aluminium with low aluminium content; Alliages uranium-aluminium a faible teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Cabane, G; Englander, M; Lehmann, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

Uranium, as obtained after spinning in phase {gamma}, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase {alpha}) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl{sub 2}) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl{sub 2} particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

DEFF Research Database (Denmark)

Henriksen, L.; Johansen, A.; Koch, J.

1967-01-01

Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

Chemical mimicking of bio-assisted aluminium extraction by Aspergillus niger's exometabolites.

Science.gov (United States)

Boriová, Katarína; Urík, Martin; Bujdoš, Marek; Pifková, Ivana; Matúš, Peter

2016-11-01

Presence of microorganisms in soils strongly affects mobility of metals. This fact is often excluded when mobile metal fraction in soil is studied using extraction procedures. Thus, the first objective of this paper was to evaluate strain Aspergillus niger's exometabolites contribution on aluminium mobilization. Fungal exudates collected in various time intervals during cultivation were analyzed and used for two-step bio-assisted extraction of alumina and gibbsite. Oxalic, citric and gluconic acids were identified in collected culture media with concentrations up to 68.4, 2.0 and 16.5 mmol L -1 , respectively. These exometabolites proved to be the most efficient agents in mobile aluminium fraction extraction with aluminium extraction efficiency reaching almost 2.2%. However, fungal cultivation is time demanding process. Therefore, the second objective was to simplify acquisition of equally efficient extracting agent by chemically mimicking composition of main organic acid components of fungal exudates. This was successfully achieved with organic acids mixture prepared according to medium composition collected on the 12th day of Aspergillus niger cultivation. This mixture extracted similar amounts of aluminium from alumina compared to culture medium. The aluminium extraction efficiency from gibbsite by organic acids mixture was lesser than 0.09% which is most likely because of more rigid mineral structure of gibbsite compared to alumina. The prepared organic acid mixture was then successfully applied for aluminium extraction from soil samples and compared to standard single step extraction techniques. This showed there is at least 2.9 times higher content of mobile aluminium fraction in soils than it was previously considered, if contribution of microbial metabolites is considered in extraction procedures. Thus, our contribution highlights the significance of fungal metabolites in aluminium extraction from environmental samples, but it also simplifies the

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content; Proprietes elastiques et plastiques des alliages fer-aluminium. Problemes particuliers poses par la fragilite des alliages a forte teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Mouturat, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [French] Cette etude comporte les resultats obtenus avec des alliages fer-aluminium dont la composition s'etend de 0 a pres de 50 atomes pour cent d'aluminium. Nous avons etudie successivement les conditions d'elaboration et de transformation, le module elastique et la limite elastique; un dernier chapitre est consacre a l'etude du phenomene Portevin-le-Chatelier dans les alliages a 40 atomes pour cent d'aluminium. I) La principale difficulte a resoudre residait dans la fragilite intergranulaire des alliages ordonnes; celle-ci a ete considerablement reduite par des conditions

Conditioning of radioactive aluminium generated by the VVR-S Nuclear Reactor Decommissioning Laboratory Inactive Tests

International Nuclear Information System (INIS)

Nicu, M.; Ionascu, L.; Turcau, C.; Dragolici, F.; Rotarescu, G.

2015-01-01

Aluminium is a reactive amphoteric metal, readily forming a protective oxide layer on contact with air or water. However, as the oxides are amphoteric, aluminium is not resistant to corrosion in acidic and alkaline conditions, because the protective films dissolve. As a consequence radioactive waste containing bulk aluminium alloys can not be embedded in Ordinary Portland Cement (OPC). A potential encapsulating material for the radioactive aluminium is potassium magnesium phosphate (MKP). This paper presents the characterization results obtained from analyzing the potential magnesium phosphate formulations and assesses its potential to reduce the corrosion of aluminium. A series of experiments have been performed. The main conclusions of the paper are as follows. First, the pH values of magnesium phosphate formulation investigated increased gradually over the test duration, with pH measurement ranging from 8.1 - 9.1, indicating lower values compared with the reference composite OPC (pH ∼ 13). The reduction of pH is an important controlling factor for the corrosion of aluminium. Secondly, according to XRD, the hardened magnesium phosphate matrix is polycrystalline and the main reaction product of magnesium phosphate cement formulations was confirmed as MgKPO 4 -6H 2 O, which was found to dominate the crystalline phase composition. Thirdly, the compressive strengths obtained for magnesium phosphate matrices investigated are included in the accepted limits for the embedding matrix with cement (above 5 N/mm 2 ). And fourthly, the corrosion of metallic aluminium in magnesium phosphate matrix is markedly reduced in comparison with the composite OPC

Influence of reinforcement proportion and matrix composition on pitting corrosion behaviour of cast aluminium matrix composites (A3xx.x/SiCp)

International Nuclear Information System (INIS)

Pardo, A.; Merino, M.C.; Merino, S.; Viejo, F.; Carboneras, M.; Arrabal, R.

2005-01-01

The influence of silicon carbide (SiCp) proportion and matrix composition on four aluminium metal matrix composites (A360/SiC/10p, A360/SiC/20p, A380/SiC/10p, A380/SiC/20p) immersed in 1-3.5 wt% NaCl at 22 deg C was investigated by potentiodynamic polarization. The kinetics of the corrosion process was studied on the basis of gravimetric measurements. The nature of corrosion products was analysed by scanning electron microscopy (SEM) and low angle X-ray diffraction (XRD). The corrosion damage in Al/SiCp composites was caused by pitting attack and by nucleation and growth of Al 2 O 3 . 3H 2 O on the material surface. The main attack nucleation sites were the interface region between the matrix and the reinforcement particles. The corrosion process was influenced more by the concentration of alloy elements in the matrix than by the proportion of SiCp reinforcement and saline concentration

Influence of reinforcement proportion and matrix composition on pitting corrosion behaviour of cast aluminium matrix composites (A3xx.x/SiCp)

Energy Technology Data Exchange (ETDEWEB)

Pardo, A. [Departamento de Ciencia de Materiales, Facultad de Quimica, Universidad Complutense, 28040 Madrid (Spain)]. E-mail: anpardo@quim.ucm.es; Merino, M.C. [Departamento de Ciencia de Materiales, Facultad de Quimica, Universidad Complutense, 28040 Madrid (Spain); Merino, S. [Departamento de Tecnologia Industrial, Universidad Alfonso X El Sabio, 28691, Villanueva de la Canada, Madrid (Spain); Viejo, F. [Departamento de Ciencia de Materiales, Facultad de Quimica, Universidad Complutense, 28040 Madrid (Spain); Carboneras, M. [Departamento de Ciencia de Materiales, Facultad de Quimica, Universidad Complutense, 28040 Madrid (Spain); Arrabal, R. [Departamento de Ciencia de Materiales, Facultad de Quimica, Universidad Complutense, 28040 Madrid (Spain)

2005-07-01

The influence of silicon carbide (SiCp) proportion and matrix composition on four aluminium metal matrix composites (A360/SiC/10p, A360/SiC/20p, A380/SiC/10p, A380/SiC/20p) immersed in 1-3.5 wt% NaCl at 22 deg C was investigated by potentiodynamic polarization. The kinetics of the corrosion process was studied on the basis of gravimetric measurements. The nature of corrosion products was analysed by scanning electron microscopy (SEM) and low angle X-ray diffraction (XRD). The corrosion damage in Al/SiCp composites was caused by pitting attack and by nucleation and growth of Al{sub 2}O{sub 3} . 3H{sub 2}O on the material surface. The main attack nucleation sites were the interface region between the matrix and the reinforcement particles. The corrosion process was influenced more by the concentration of alloy elements in the matrix than by the proportion of SiCp reinforcement and saline concentration.

Experimental Realisation of Elusive Multiple-bonded Aluminium Compounds: A New Horizon in the Aluminium Chemistry.

Science.gov (United States)

Inoue, Shigeyoshi; Bag, Prasenjit; Weetman, Catherine

2018-05-23

Synthesis and isolation of stable main group compounds featuring multiple bonds has been of keen interest for the last several decades. Multiply bonded complexes were obtained using sterically demanding substituents that provide kinetic and thermodynamic stability. Many of these compounds have unusual structural and electronic properties that challenges the classical concept of covalent multiple bonding. In contrast, analogous aluminium compounds are scarce in spite of its high natural abundance. The parent dialumene (Al2H2) has been calculated to be extremely weak, thus making Al multiple bonds a challenging synthetic target. This review provides an overview of these recent advances in the cutting edge synthetic approaches used to obtain aluminium homo- and heterodiatomic multiply bonded complexes. Additionally, the reactivity of these novel compounds towards various small molecules and reagents will be discussed herein. This review provides an overview on the current progress in aluminium multiple bond chemistry and the careful ligand design required to stabilise these reactive species. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ballistic impact velocity response of carbon fibre reinforced aluminium alloy laminates for aero-engine

Science.gov (United States)

Mohammed, I.; Abu Talib, A. R.; Sultan, M. T. H.; Saadon, S.

2017-12-01

Aerospace and other industries use fibre metal laminate composites extensively due to their high specific strength, stiffness and fire resistance, in addition to their capability to be tailored into different forms for specific purposes. The behaviours of such composites under impact loading is another factor to be considered due to the impacts that occur in take-off, landing, during maintenance and operations. The aim of the study is to determine the specific perforation energy and impact strength of the fibre metal laminates of different layering pattern of carbon fibre reinforced aluminium alloy and hybrid laminate composites of carbon fibre and natural fibres (kenaf and flax). The composites are fabricated using the hand lay-up method in a mould with high bonding polymer matrix and compressed by a compression machine, cured at room temperature for one day and post cure in an oven for three hours. The impact tests are conducted using a gun tunnel system with a flat cylindrical bullet fired using a helium gas at a distance of 14 inches to the target. Impact and residual velocity of the projectile are recorded by high speed video camera. Specific perforation energy of carbon fibre reinforced aluminium alloy (CF+AA) for both before and after fire test are higher than the specific perforation energy of the other composites considered before and after fire test respectively. CF +AA before fire test is 55.18% greater than after. The same thing applies to impact strength of the composites where CF +AA before the fire test has the highest percentage of 11.7%, 50.0% and 32.98% as respectively compared to carbon fibre reinforced aluminium alloy (CARALL), carbon fibre reinforced flax aluminium alloy (CAFRALL) and carbon fibre reinforced kenaf aluminium alloy (CAKRALL), and likewise for the composites after fire test. The considered composites in this test can be used in the designated fire zone of an aircraft engine to protect external debris from penetrating the engine

Study of mechanical properties on powdermetalurgy aluminium matrix composites fabricated by stamping or extrusion

International Nuclear Information System (INIS)

Busquets, D.; Gomez, L.; Amigo, V.; Salvador-Moya, M. D.

2005-01-01

We have developed composite materials from AA6061 aluminium alloy powders used as matrix and ceramics powders of boron carbide, silicon carbide and boron nitride, used as reinforcements in 2.5, 5.0, 7.5 and 10% vol. by mechanical mixing and milling in planetary mill at 360 rpm vial velocity for 4 h followed of hot stamping and extrusion process on green compacts. Mechanical properties obtained from tensile tests are influenced by the heat treatment, reinforcement fractions and nature. Moreover, these mechanical characteristic are dependent from the processing route. Optical and Scanning Electron Microscopy analysis revealed the microstructure of materials and let describe the tripartite relation; structure-processing-properties, of the developed materials. (Author) 20 refs

Silicon Alloying On Aluminium Based Alloy Surface

International Nuclear Information System (INIS)

Suryanto

2002-01-01

Silicon alloying on surface of aluminium based alloy was carried out using electron beam. This is performed in order to enhance tribological properties of the alloy. Silicon is considered most important alloying element in aluminium alloy, particularly for tribological components. Prior to silicon alloying. aluminium substrate were painted with binder and silicon powder and dried in a furnace. Silicon alloying were carried out in a vacuum chamber. The Silicon alloyed materials were assessed using some techniques. The results show that silicon alloying formed a composite metal-non metal system in which silicon particles are dispersed in the alloyed layer. Silicon content in the alloyed layer is about 40% while in other place is only 10.5 %. The hardness of layer changes significantly. The wear properties of the alloying alloys increase. Silicon surface alloying also reduced the coefficient of friction for sliding against a hardened steel counter face, which could otherwise be higher because of the strong adhesion of aluminium to steel. The hardness of the silicon surface alloyed material dropped when it underwent a heating cycle similar to the ion coating process. Hence, silicon alloying is not a suitable choice for use as an intermediate layer for duplex treatment

The effect of surface pre-conditioning treatments on the local composition of Zr-based conversion coatings formed on aluminium alloys

Science.gov (United States)

Cerezo, J.; Vandendael, I.; Posner, R.; de Wit, J. H. W.; Mol, J. M. C.; Terryn, H.

2016-03-01

This study investigates the effect of different alkaline, acidic and thermal pre-conditioning treatments applied to different Al alloy surfaces. The obtained results are compared to the characteristics of Zr-based conversion coatings that were subsequently generated on top of these substrates. Focus is laid on typical elemental distributions on the sample surfaces, in particular on the amount of precipitated functional additives such as Cu species that are present in the substrate matrix as well as in the conversion bath solutions. To this aim, Field Emission Auger Electron spectra, depth profiles and surface maps with superior local resolution were acquired and compared to scanning electron microscopy images of the sample. The results show how de-alloying processes, which occur at and around intermetallic particles in the Al matrix during typical industrial alkaline or acidic cleaning procedures, provide a significant source of crystallization cores for any following coating processes. This is in particular due for Cu-species, as the resulting local Cu structures on the surface strongly affect the film formation and compositions of state-of-the-art Zr-based films. The findings are highly relevant for industrial treatments of aluminium surfaces, especially for those that undergo corrosion protection and painting process steps prior to usage.

The varied functions of aluminium-activated malate transporters–much more than aluminium resistance

Science.gov (United States)

Palmer, Antony J.; Baker, Alison; Muench, Stephen P.

2016-01-01

The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. PMID:27284052

Synthesis, properties, and assimilation methods of aluminium hydride

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2013-01-01

We have discovered a new source of aluminium hydride-conversion of tetrahydrofurane under influence of halogenous alkyls. We have proposed the chlorbenzene method of synthesis of AlH 3 , which excludes adhesion and ensure high quality of the product with respect to its purity, thermal stability, habits of crystals (round shape), and granulometric composition. We determined capability of benzyl chloride to fix AlH 4 -groups by the way of complexes formation. This allows increasing efficient concentration of AlH 3 solutions and their productivity. We have carried out 'direct' crystallization of aluminium hydride in one stage using interaction of binary metal hydride with aluminium chloride in the medium of ether-toluene at 60-100 d ig C a nd using solvent distillation. In the reaction of Li H with AlCl 3 , we achieved output of pure crystal AlH 3 of hexagonal modification, which was close to quantitative. We have discovered the assimilation methods of aluminium hydride in carrying out of solid-phase chemical reactions. (author)

An investigation of flow properties of metal matrix composites suspensions for injection molding

International Nuclear Information System (INIS)

Ahmad, F.; Bevis, M.J.

1997-01-01

Flow properties of metal matrix composites suspensions have significant effects on the fibre orientation during mould filling. The results presented in this paper relate to the flow properties of aluminium powder and glass fibres compounded into a sacrificial thermoplastics binder. For this purpose, a range of aluminium compounds and aluminium composite suspensions were investigated over a wide shear rate range expected to occur during injection mould process. Aluminium composites wee prepared by substituting glass fibres for aluminium in aluminium compound. Aluminium composite containing a maximum critical volume fraction of fibres which did not exhibit an increase n viscosity was determined. The effect of temperature on the flow behaviour of aluminium composite was also investigated. (author)

Thermodynamic properties of uranium in gallium–aluminium based alloys

International Nuclear Information System (INIS)

Volkovich, V.A.; Maltsev, D.S.; Yamshchikov, L.F.; Chukin, A.V.; Smolenski, V.V.; Novoselova, A.V.; Osipenko, A.G.

2015-01-01

Activity, activity coefficients and solubility of uranium was determined in gallium-aluminium alloys containing 1.6 (eutectic), 5 and 20 wt.% aluminium. Additionally, activity of uranium was determined in aluminium and Ga–Al alloys containing 0.014–20 wt.% Al. Experiments were performed up to 1073 K. Intermetallic compounds formed in the alloys were characterized by X-ray diffraction. Partial and excess thermodynamic functions of U in the studied alloys were calculated. - Highlights: • Thermodynamics of uranium is determined in Ga–Al alloys of various compositions. • Uranium in the mixed alloys interacts with both components, Ga and Al. • Interaction of U with Al increases with decreasing temperature. • Activity and solubility of uranium depend on Al content in Ga–Al alloys.

Thermodynamic properties of uranium in gallium–aluminium based alloys

Energy Technology Data Exchange (ETDEWEB)

Volkovich, V.A., E-mail: v.a.volkovich@urfu.ru [Department of Rare Metals and Nanomaterials, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Maltsev, D.S.; Yamshchikov, L.F. [Department of Rare Metals and Nanomaterials, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Chukin, A.V. [Department of Theoretical Physics and Applied Mathematics, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Smolenski, V.V.; Novoselova, A.V. [Institute of High-Temperature Electrochemistry UD RAS, Ekaterinburg, 620137 (Russian Federation); Osipenko, A.G. [JSC “State Scientific Centre - Research Institute of Atomic Reactors”, Dimitrovgrad, 433510 (Russian Federation)

2015-10-15

Activity, activity coefficients and solubility of uranium was determined in gallium-aluminium alloys containing 1.6 (eutectic), 5 and 20 wt.% aluminium. Additionally, activity of uranium was determined in aluminium and Ga–Al alloys containing 0.014–20 wt.% Al. Experiments were performed up to 1073 K. Intermetallic compounds formed in the alloys were characterized by X-ray diffraction. Partial and excess thermodynamic functions of U in the studied alloys were calculated. - Highlights: • Thermodynamics of uranium is determined in Ga–Al alloys of various compositions. • Uranium in the mixed alloys interacts with both components, Ga and Al. • Interaction of U with Al increases with decreasing temperature. • Activity and solubility of uranium depend on Al content in Ga–Al alloys.

Site specific SEM/FIB/TEM for analysis of lubricated sliding wear of aluminium alloy composites

International Nuclear Information System (INIS)

Walker, J C; Jones, H; Rainforth, W M

2006-01-01

Although extensive research has been undertaken into the dry sliding wear of aluminium alloys, only limited work has been reported on lubricated wear. In this paper, the lubricated sliding wear of some powder derived aluminium alloy composites is reported. Stereo pairs of the worn surface were obtained in the SEM and digitally reconstructed to give an accurate projection of the surface topography. Analysis of the average surface roughness (R a ) along chosen sections provided quantitative information about the wear mechanism. Following this, dual beam focused ion beam (FIB) was undertaken to further explore the features revealed by the SEM surface reconstructions, with TEM sections removed from selected regions. Surface deformation was confined to a narrow layer, typically 1μm thick. Subgrain size within the subsurface layer was comparable to that found in dry sliding wear tests. Reinforcement fracture occurred in the surface particles only. The resultant fragments were often incorporated back into the surface following detachment, such that the total volume fraction reinforcement at the surface was greater than in the bulk. Thus, the dynamic surface topography was a result of three factors: surface deformation, local detachment of reinforcement and re-incorporation of the fragments back into the surface

Aluminium in human sweat.

Science.gov (United States)

Minshall, Clare; Nadal, Jodie; Exley, Christopher

2014-01-01

It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans. Copyright © 2013 Elsevier GmbH. All rights reserved.

Bonding of aluminium matrix composites for application in the transport industry

International Nuclear Information System (INIS)

Urena, A.; Gomez de Salazar, J.M.

1993-01-01

A discontinuously reinforced MMC containing 12 vol % SiC particles in an Al-Cu-Mg alloy (AA 2124) matrix has been diffusion bonded. Thick interlayers of different superplastic aluminium alloys (Al-Li 8090 and Al-Cu SUPRAL) were used to reduce the bonding pressure and ensure complete surface contact. Microstructural studies shown higher continuity in joints bonded with 8090 interlayer than with other alloys. Precipitation of rich-copper intermetallic was detected, after bonding, in the interlayer because diffusion of Cu from 2124 matrix. Results suggest that Li contained in the interlayer favours the partial disruption of the aluminium oxide film, making easier the solid state bonding. (orig.)

Removal of chromium (VI) from water by micro-alloyed aluminium ...

African Journals Online (AJOL)

driniev

2004-07-03

Jul 3, 2004 ... aluminium composite (MAlC) under flow conditions ... Behaviour of the composite in water is under significant influence of pH, which affects its efficacy and .... 1.2 x 1.2 mm, ∅ 0.6) with MAl, by means of a special gas burner.

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content; Proprietes elastiques et plastiques des alliages fer-aluminium. Problemes particuliers poses par la fragilite des alliages a forte teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Mouturat, P. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [French] Cette etude comporte les resultats obtenus avec des alliages fer-aluminium dont la composition s'etend de 0 a pres de 50 atomes pour cent d'aluminium. Nous avons etudie successivement les conditions d'elaboration et de transformation, le module elastique et la limite elastique; un dernier chapitre est consacre a l'etude du phenomene Portevin-le-Chatelier dans les alliages a 40 atomes pour cent d'aluminium. I) La principale difficulte a resoudre residait dans la fragilite intergranulaire des alliages ordonnes; celle-ci a ete

The varied functions of aluminium-activated malate transporters-much more than aluminium resistance.

Science.gov (United States)

Palmer, Antony J; Baker, Alison; Muench, Stephen P

2016-06-15

The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. © 2016 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

Laser surface alloying (LSA) of aluminium (AA 1200) with TiB2 for hardness improvement

CSIR Research Space (South Africa)

Popoola, AP

2010-10-01

Full Text Available The present work deals with the development of Aluminium metal matrix composite (MMC) using TiB2 reinforcement. The aim is to improve the microhardness property of the substrate. The surface of the aluminium was sand blasted to improve its laser...

Computer modelling of age hardening for cast aluminium alloys

International Nuclear Information System (INIS)

Wu, Linda; Ferguson, W George

2009-01-01

Age hardening, or precipitation hardening, is one of the most widely adopted techniques for strengthening of aluminium alloys. Although various age hardening models have been developed for aluminium alloys, from the large volume of literature reviewed, it appears that the bulk of the research has been concentrated on wrought aluminium alloys, only a few of the established precipitation models have been applied to the casting aluminium alloys. In the present work, there are two modelling methods that have been developed and applied to the casting aluminium alloys A356 and A357. One is based on the Shercliff-Ashby methodology to produce a process model, by which we mean a mathematical relationship between process variables (alloy composition, ageing temperature and time) and material properties (yield strength or hardness) through microstructure evolution (precipitate radius, volume fraction). The other method is based on the Kampmann and Wagner Numerical (KWN) model which deals with concomitant nucleation, growth and coarsening and is thus capable of predicting the full evolution of the particle size distribution and then a strength model is used to evaluate the resulting change in hardness or yield strength at room temperature by taking into account contributions from lattice resistance, solid solution hardening and precipitation hardening.

Corrosion behaviour of nanometre sized cerium oxide and titanium oxide incorporated aluminium in NaCl solution

International Nuclear Information System (INIS)

Ashraf, P. Muhamed; Edwin, Leela

2013-01-01

Highlights: ► Corrosion resistant aluminium incorporated with nano oxides of cerium and titanium. ► 0.2% nano CeO 2 and 0.05% nano TiO 2 showed increased corrosion resistance. ► Nano TiO 2 concentration influenced the optimum performance of the material. ► Comparison of Micro and nano CeO 2 and TiO 2 aluminium showed the latter is best. - Abstract: The study highlights the development of an aluminium matrix composite by incorporating mixture of nanometre sized cerium oxide and titanium oxide in pure aluminium and its corrosion resistance in marine environment. The mixed nanometre sized oxides incorporated aluminium exhibited improved microstructure and excellent corrosion resistance. Corrosion resistance depends on the concentration of nanometre sized titanium oxide. Electrochemical characteristics improved several folds in nanometre sized mixed oxides incorporated aluminium than micrometre sized oxides incorporated aluminium.

Human exposure to aluminium.

Science.gov (United States)

Exley, Christopher

2013-10-01

Human activities have circumvented the efficient geochemical cycling of aluminium within the lithosphere and therewith opened a door, which was previously only ajar, onto the biotic cycle to instigate and promote the accumulation of aluminium in biota and especially humans. Neither these relatively recent activities nor the entry of aluminium into the living cycle are showing any signs of abating and it is thus now imperative that we understand as fully as possible how humans are exposed to aluminium and the future consequences of a burgeoning exposure and body burden. The aluminium age is upon us and there is now an urgent need to understand how to live safely and effectively with aluminium.

Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

DEFF Research Database (Denmark)

Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib

2007-01-01

A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis...... aluminium content in aluminium hydroxide suspension. (c) 2007 Elsevier Ltd. All rights reserved....

Chemical composition and morphology of oxidic ceramics at filtration of steel deoxidised by aluminium

Directory of Open Access Journals (Sweden)

J. Bažan

2009-10-01

Full Text Available Composition and morphology of filter ceramics were investigated during filtration of steel deoxidised by aluminium. Filtration was realized with use of filters based on oxidic ceramics Cr2O3, TiO2, SiO2, ZrO2, Al2O3, 3Al2O3•2SiO2 and MgO•Al2O3. It was established that change of interphase (coating occurs during filtration of steel on the surface of capillaries of ceramics, where content of basic oxidic component decreases. Loss of oxidic component in the coating is replaced by increase of oxides of manganese and iron and it is great extent inversely proportional to the value of Gibbs’ energy of oxide, which forms this initial basis of ceramics.

Effect of Bio char on Plant Growth and Aluminium Form of Soil under Aluminium Stress

Science.gov (United States)

Qian, Lianwen; Li, Qingbiao; Sun, Jingwei; Feng, Ying

2018-01-01

Aluminium-enriched acid red soils in South China easily cause aluminium toxicity to plants, but biochip can improve soils and eliminate soil contaminations. In this project, biochip was used in potted plant control test to study the effect of biochip on plant growth in soil under acid aluminium stress and the migration and conversion of aluminium in plant-soil system. The fin dings show that the application of biochip increases the pH value of soil under aluminium stress significantly, changes the existing form of aluminium ion in soil, reduces the plants’ absorption of aluminium, and alleviates the aluminium toxicity to plants, but too much biochip may inhibit the growth of plants. In this case, further study should be carried out as regards the volume and way of biochip input in practical applications as well as the timeliness of aluminium toxicity removal.

Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates

International Nuclear Information System (INIS)

Chekhonin, Paul; Beausir, Benoît; Scharnweber, Juliane; Oertel, Carl-Georg; Hausöl, Tina; Höppel, Heinz Werner; Brokmeier, Heinz-Günter; Skrotzki, Werner

2012-01-01

Aluminium laminates consisting of high-purity aluminium and commercially pure aluminium have been produced by accumulative roll bonding (ARB) at ambient temperature for up to 10 cycles. To study the microstructure and texture development of the high-purity aluminium layers with regard to the shrinking layer thickness during ARB, microstructure and texture investigations were carried out by electron backscatter diffraction and neutron and X-ray diffraction, respectively. While the commercially pure aluminium layers develop an ultrafine-grained microstructure, partial discontinuous recrystallization occurs in the high-purity layers. The texture of the high-purity layers mainly consists of Cube and “Tilted Cube” (tilted with respect to the transverse direction) components. The experimental results are discussed with respect to confined recrystallization in the ARB aluminium laminates.

Alloys of uranium and aluminium with low aluminium content

International Nuclear Information System (INIS)

Cabane, G.; Englander, M.; Lehmann, J.

1955-01-01

Uranium, as obtained after spinning in phase γ, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase α) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl 2 ) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl 2 particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

Phase transformation of aluminium hydroxide to aα- alumina prepared from different aluminium salts

International Nuclear Information System (INIS)

Masliana Muslimin; Meor Yusoff Meor Sulaiman

2006-01-01

The study intends to look at the most suitable aluminium salt to produce a single-phase a-alumina by the hydrothermal method. In the process to produce alumina from the calcination of aluminium hydroxide (Al(OH) 3 ), three different aluminium salts namely aluminium sulfate (Al 2 (SO 4) 2), aluminium nitrate (A(NO 3 ) 3 ) and aluminium chloride (AlCl 3 ) were tried. The process involved the used of NH 4 OH as the precipitating medium. Aluminium hydroxide produced from each of these salts were characterised by x-ray diffraction (XRD) technique to identity the crystalline phase. Aluminium hydroxide produced by all the different aluminium salts is present as boehmite or pseudo-boehmite phase. Aluminium hydroxide produced from Al 2 (SO) 2 , Al(NO) 3 and AlCl 3 shows the transformation of the boehmite phase to a α-alumina phase at 500 0 C. On further heating, the α-alumina continuously formed at 800 o C followed soon at 1000 o C. But for the Al(NO3) 3 salts a different phase transitions occurs on heating especially at 1000 o C. Here it was observed not a single alumina phase is presence but the presence of both α and γ--alumina phases. At 1300 o C, the single α-alumina phase was formed. The study concluded that aluminium sulphate is recommended in order to obtain a single-phase α-alumina with the required characteristics. (Author)

Aluminium base amorphous and crystalline alloys with Fe impurity

International Nuclear Information System (INIS)

Sitek, J.; Degmova, J.

2006-01-01

Aluminium base alloys show remarkable mechanical properties, however their low thermal stability still limits the technological applications. Further improvement of mechanical properties can be reached by partial crystallization of amorphous alloys, which gives rise to nanostructured composites. Our work was focused on aluminium based alloys with Fe, Nb and V additions. Samples of nominal composition Al 90 Fe 7 Nb 3 and Al 94 Fe 2 V 4 were studied in amorphous state and after annealing up to 873 K. From Moessbauer spectra taken on the samples in amorphous state the value of f-factor was determined as well as corresponding Debye temperatures were calculated. Annealing at higher temperatures induced nano and microcrystalline crystallization. Moessbauer spectra of samples annealed up to 573 K are fitted only by distribution of quadrupole doublets corresponding to the amorphous state. An increase of annealing temperature leads to the structural transformation, which consists in growth of nanometer sized aluminium nuclei. This is partly reflected in Moessbauer parameters. After annealing at 673 K intermetallic phase Al 3 Fe and other Al-Fe phases are created. In this case Moessbauer spectra are fitted by quadrupole doublets. During annealing up to 873 K large grains of Fe-Al phases are created. (authors)

Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

DEFF Research Database (Denmark)

Aggerbeck, Martin

potential differences in the microstructure, and protection from the network of the Al3Ti phases precipitated during the heat treatment. Laser surface cladding of aluminium containing up to 20 wt. % Ti6Al4V were studied focusing on the microstructure and the alkaline corrosion properties. Due......The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions...... that the roughness after etching increases with higher amounts of alloying elements (especially iron and silicon). Proper polishing requires some alloy hardness, while alloy purity is required for a glossy appearance after anodisation. Magnetron sputtered aluminium based coatings containing up to 18 wt. % titanium...

Influence of aluminium content on thermodynamic function of LaNi5-xAlx

International Nuclear Information System (INIS)

Xiong Yifu; Cheng Huchi; Luo Deli

2000-01-01

Hydriding thermodynamic parameters were measured on alloys of the general composition of LaNi 5-x Al x (x = 0.0, 0.1, 0.2, 0.3) under isothermal and isochoric conditions. The results show that the equilibrium pressure, hydrogen capacity and thermodynamic parameters such as ΔH, ΔS decrease with aluminium content, plateau slopes of the P-C-T curve increase with aluminium content

Transmission electron microscopy observations on phase transformations during aluminium/mullite composites formation by gas pressure infiltration

Energy Technology Data Exchange (ETDEWEB)

Pawlyta, M., E-mail: miroslawa.pawlyta@polsl.pl [Silesian University of Technology, Institute of Engineering Materials and Biomaterials, Konarskiego 18A, 44-100 Gliwice (Poland); Tomiczek, B.; Dobrzański, L.A.; Kujawa, M. [Silesian University of Technology, Institute of Engineering Materials and Biomaterials, Konarskiego 18A, 44-100 Gliwice (Poland); Bierska-Piech, B. [Silesian Centre for Education and Interdisciplinary Research, 75 Pułku Piechoty 1A, 41-500 Chorzów (Poland)

2016-04-15

The porous ceramic preforms were manufactured using the powder metallurgy technique. First, the start-up material (halloysite with the addition of carbon fibres as the pore-forming agent) was slowly heated to 800 °C and then sintered at 1300 °C. Degradation of the carbon fibres enabled the open canals to form. At the end of the sintering process, the porous ceramic material consisting mainly of two phases (mullite and cristobalite) was formed, without any residual carbon content. During infiltration, the liquid metal filled the empty spaces (pores) effectively and formed the three-dimensional network of metal in the ceramic. The cristobalite was almost entirely decomposed. In the areas of its previous occurrence, there are new pores, only in the ceramic grains. The mullite, which was formed from halloysite during annealing, crystallized in the Pbam orthorhombic space group, with the (3Al{sub 2}O{sub 3}·2SiO{sub 2}) stoichiometric composition. The mullite structure does not change during the infiltration. The composite components are tightly connected. A transition zone between the ceramics and the metal, having the thickness of about 200 nm, was formed. The nanocrystalline zone, identified as γ-Al{sub 2}O{sub 3}, was formed by diffusing the product of the cristobalite decomposition into the aluminium alloy matrix. There is an additional, new phase, identified as (Mg,Si)Al{sub 2}O{sub 4} in the outer parts of the transition zone. - Highlights: • Phase changes after the infiltration of aluminium into porous mullite preforms were observed by TEM. • TEM observations confirm that during infiltration cristobalite was decomposed and the structure of mullite did not change. • Between the ceramic and the metal, a transition zone comprising a layer of γ-Al{sub 2}O{sub 3} and (Mg,Si)Al{sub 2}O{sub 4} was formed.

The quality of our drinking water: aluminium determination with an acoustic wave sensor.

Science.gov (United States)

Veríssimo, Marta I S; Gomes, M Teresa S R

2008-06-09

A new methodology based on an inexpensive aluminium acoustic wave sensor is presented. Although the aluminium sensor has already been reported, and the composition of the selective membrane is known, the low detection limits required for the analysis of drinking water, demanded the inclusion of a preconcentration stage, as well as an optimization of the sensor. The necessary coating amount was established, as well as the best preconcentration protocol, in terms of oxidation of organic matter and aluminium elution from the Chelex-100. The methodology developed with the acoustic wave sensor allowed aluminium quantitation above 0.07 mg L(-1). Several water samples from Portugal were analysed using the acoustic wave sensor, as well as by UV-vis spectrophotometry. Results obtained with both methodologies were not statistically different (alpha=0.05), both in terms of accuracy and precision. This new methodology proved to be adequate for aluminium quantitation in drinking water and showed to be faster and less reagent consuming than the UV spectrophotometric methodology.

Coprecipitation of yttrium and aluminium hydroxide for preparation of yttrium aluminium garnet

NARCIS (Netherlands)

Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.

1990-01-01

Coprecipitation of yttrium and aluminium hydroxide for the preparation of pure yttrium aluminium garnet (YAG) powder with small grain size is the subject of this study. Starting materials are sulphates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3Al5O12), the pH during flocculation

Characterisation of the residual strain profiles in aluminium titanate/alumina functionally graded materials using x-ray diffraction data

International Nuclear Information System (INIS)

Skala, R.D.

2002-01-01

Full text: In previous studies of the aluminium titanate/alumina functionally graded system, it was proposed that the mechanisms responsible for the observed flaw tolerance and quasi-ductile behaviour of the composite system were due to the generation of residual strain fields in the bulk of the composite. These residual strain fields are induced by a combination of the thermal expansion coefficient mismatch between the alumina and aluminium titanate phases and also the high degree of thermal anisotropy exhibited by the aluminium titanate phase. In the current study, both the macro-strain (linear) and micro-strain (non-linear) were extracted from x-ray diffraction data. The macro-strains were extracted from variations in the lattice parameters, whilst the micro-strains were extracted from line broadening of the diffraction peaks. Strain profiles were obtained by carefully removing layers of the composite till the centre region was reached. Analysis of the data showed that the macro-strain in the alumina phase was compressive and decreased from -0.149 ± 0.012 % at the surface to -0.086 ± 0.006 % at the centre of the composite system. The macro-strain in the aluminium titanate phase was observed to remain constant at a value of 0.181 ± 0.013 % and be tensile in nature. The micro-strains within the composite system were also seen to exhibit a similar profile with the micro-strain in the alumina phase ranging from 0.065 ± 0.003 % to 0.008 ± 0.005 % from the surface to the centre respectively and the aluminium titanate phase displaying a mean micro-strain value of 0.117 ± 0.033 %. These results were also seen to correlate well with the compositional profiles observed in previous studies of the system. Copyright (2002) Australian X-ray Analytical Association Inc

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content

International Nuclear Information System (INIS)

Mouturat, P.

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [fr

Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

Energy Technology Data Exchange (ETDEWEB)

Moe, J [Oslo Univ. (Norway)

1996-01-01

The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

Aluminium alloys welding with high-power Nd:YAG lasers

International Nuclear Information System (INIS)

Garcia Orza, J.A.

1998-01-01

Aluminium alloys have good mechanical properties (high strength-to-weight ratio, corrosion resistance) and good workability. their applications are growing up, specially in the transportation industry. Weldability is however poorer than in other materials; recent advances in high power YAG laser are the key to obtain good appearance welds and higher penetration, at industrial production rates. Results of the combination of high power YAG beams with small fiber diameters and specific filler wires are presented. It is also characterized the air bone particulate material, by-product of the laser process: emission rates, size distribution and chemical composition are given for several aluminium alloys. (Author) 6 refs

A study of aluminium-exposed fish using a scanning proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Cholewa, M; Legge, G L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Eeckhaoudt, S; Van Grieken, R [Universitaire Instelling Antwerpen, Antwerp (Belgium)

1994-12-31

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs.

A study of aluminium-exposed fish using a scanning proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Cholewa, M.; Legge, G.L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Eeckhaoudt, S.; Van Grieken, R. [Universitaire Instelling Antwerpen, Antwerp (Belgium)

1993-12-31

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs.

A study of aluminium-exposed fish using a scanning proton microprobe

International Nuclear Information System (INIS)

Cholewa, M.; Legge, G.L.F.

1993-01-01

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs

Effect of Lubrication on Sliding Wear of Red Mud Particulate Reinforced Aluminium Alloy 6061

Directory of Open Access Journals (Sweden)

N. Panwar

2017-09-01

Full Text Available In present study, Red mud, an industrial waste, has been utilized as a reinforcement material to fabricate Aluminium 6061 matrix based metal matrix composite. Taguchi L18 orthogonal array has been employed for fabrication of composite castings and for conducting the tribological experimentation. ANOVA analysis has been applied to examine the effect of individual parameters such as sliding condition: dry and wet, reinforcement weight fraction, load, speed, and sliding distance on specific wear rate obtained experimentally. It has been found that tensile strength and impact energy increases while elongation decreases, with increasing weight fraction and decrease in particle size of red mud. The percentage contribution of the effect of factors on SWR is Sliding condition (73.17, speed (7.84, percentage reinforcement (7.35, load (5.75, sliding distance (2.24, and particle size (1.25. It has also been observed that specific wear rate is very low in wet condition. However, it decreases with increase in weight fraction of reinforcement, decrease in load and sliding speed. Al6061/red mud metal matrix composites have shown reasonable strength and wear resistance. The use of red mud in Aluminium composite provides the solution for disposal of red mud and can possibly become an economic replacement of Aluminium and its alloys.

Dispersion strengthening of aluminium-aluminium-oxide products

DEFF Research Database (Denmark)

Hansen, Niels

1970-01-01

The true stress-true strain curves at room temperature and at 400°C were determined for various types of aluminium-aluminium-oxide products containing from 0.2 to 4.7 weight per cent of aluminium oxide. The effect of particles on the initial flow stress and the flow stress for 0.2% offset at room...... temperature and at 400°C is in agreement with Orowan's theory. The increase in flow stress at room temperature for strain values below 3 per cent was related to the plastic strain by the equation σ-σoy=k1ε 1/2, where σoy is the initial flow stress and where k1 increases for increasing volume fraction...... and decreasing particle size of the dispersed particles. A general expression for k1 was derived for the relationship between the dislocation density and the strain in dispersion-strengthened products...

The prophylactic reduction of aluminium intake.

Science.gov (United States)

Lione, A

1983-02-01

The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail.

Development of an on-line electrochemical analyser for trace level aluminium

International Nuclear Information System (INIS)

Chow, Christopher W.K.; Thomas, Shaun D.; Davey, David E.; Mulcahy, Dennis E.; Drikas, Mary

2003-01-01

An in-house designed computerised flow injection (FI) system for low-level aluminium analysis is examined. A simple, low cost electrochemical detection system has been implemented with computerised control and data acquisition system. The system consists of a commercial electrochemical analyser, FI components (manifold, pumps and valves) and an in-house designed control system to perform automated analysis. This system was developed to study aluminium speciation in water, particularly for drinking water. The analytical technique was based upon the complexation reaction between aluminium and a ligand--DASA (1,2-dihydroxy-anthraquinone-3-sulphonic acid). 'Labile' and total aluminium concentrations, Al labile and Al total , respectively, were determined by measuring the sample before and after UV irradiation by amperometry at +0.6 V. The limit of detection for this technique was 10 μg/l (0.37 μM) and the linear calibration range was up to 1.6 mg/l (60 μM) with r 2 value of 0.999. The Al labile /Al total ratios of the water treated by 40, 80 and 100 mg/l of alum using a laboratory scale pilot plant to simulate conventional drinking water treatment processes were found to be 0.4, 0.5 and 0.8, respectively. These results indicated that when higher alum dose was employed, the residual aluminium was present mostly as the 'labile' species. Whereas, if the treatment process was not running at its optimum condition (underdosing), a large portion of aluminium was present as natural organic matter (NOM) - aluminium complexes in the treated water. The system offers a practical and effective means of providing extended knowledge of residual aluminium in drinking water

Mechanochemical synthesis of aluminium nanoparticles and their deuterium sorption properties to 2 kbar

International Nuclear Information System (INIS)

Paskevicius, M.; Webb, J.; Pitt, M.P.; Blach, T.P.; Hauback, B.C.; Gray, E.MacA.; Buckley, C.E.

2009-01-01

A mechanochemical synthesis process has been used to synthesise aluminium nanoparticles. The aluminium is synthesised via a solid state chemical reaction which is initiated inside a ball mill at room temperature between either lithium (Li) or sodium (Na) metal which act as reducing agents with unreduced aluminium chloride (AlCl 3 ). The reaction product formed consists of aluminium nanoparticles embedded within a by-product salt phase (LiCl or NaCl, respectively). The LiCl is washed with a suitable solvent resulting in aluminium (Al) nanoparticles which are not oxidised and are separated from the by-product phase. Synthesis and washing was confirmed using X-ray diffraction (XRD). Nanoparticles were found to be ∼25-100 nm from transmission electron microscopy (TEM) and an average size of 55 nm was determined from small angle X-ray scattering (SAXS) measurements. As synthesised Al/NaCl composites, washed Al nanoparticles, and purchased Al nanoparticles were deuterium (D 2 ) absorption tested up to 2 kbar at a variety of temperatures, with no absorption detected within system resolution.

Application of Anodization Process for Cast Aluminium Surface Properties Enhancement

Directory of Open Access Journals (Sweden)

Włodarczyk-Fligier A.

2016-09-01

Full Text Available An huge interest is observed in last years in metal matrix composite, mostly light metal based, which have found their applications in many industry branches, among others in the aircraft industry, automotive-, and armaments ones, as well as in electrical engineering and electronics, where one of the most important issue is related to the corrosion resistance, especially on the surface layer of the used aluminium alloys. This elaboration presents the influence of ceramic phase on the corrosion resistance, quality of the surface layer its thickness and structure of an anodic layer formed on aluminium alloys. As test materials it was applied the aluminium alloys Al-Si-Cu and Al-Cu-Mg, for which heat treatment processes and corrosion tests were carried out. It was presented herein grindability test results and metallographic examination, as well. Hardness of the treated alloys with those ones subjected to corrosion process were compared.

Impact toughness of laser alloyed aluminium AA1200 alloys

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2013-08-01

Full Text Available ),. 559-563. [2] T. Tomida, K. Nakata, S. Saji, T. Kubo, T, Formation of metal matrix composite layer on aluminium alloy with TiC-Cu powder by laser surface alloying process; Surface and Coatings Technology; vol. 142-144, 2001, 585-589. [3] L. A. B...

Bioaccumulation of aluminium in the seagrasses Cymodocea nodosa (Ucria) Aschers. and Posidonia oceanica (L.) Delile and macroalgae of the Gulf of Antikyra (Greece)

Energy Technology Data Exchange (ETDEWEB)

Malea, P. [Thessaloniki Univ. (Greece). Inst. of Botany

1993-12-31

Mean concentrations of Aluminium ({+-}SE) in two seagrasses, four Chlorophytes, three Chromophytes and seven Rhodophyte species from the Gulf of Antikyra (Greece) decreased in the order: Chlorophyta > Chromophyta > Rhodophyta > P. oceanica > C. nodosa. This area is of particular interest because of the bauxite composition of the substrate and of the wate discharge from an aluminium factory in the Gulf. Aluminium concentrations in the two seagrasses were evenly distributed at the Gulf stations. Only the concentrations of Al in C. nodosa displayed significant seasonal variation. The mean concentrations increased from spring to summer, at which point they reached their maxima. This pattern is discussed in relation to the leaf-age of the seagrass. Regarding the amount of Al accumulated by the macroalgae of each division, there were interspecific differences which were attributed to differences in the structure, the ecology and the binding sites offered by the plants. The dependence of Al concentrations in the macrophytes on the concentrations in the sediment and the correlation of Al concentrations with the concentrations of some other metals in the plants were also investigated. (orig.)

Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

Science.gov (United States)

Grove, C. A.; Judd, G.; Ansell, G. S.

1972-01-01

Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

An Facile High-Density Polyethylene - Exfoliated Graphite - Aluminium Hydroxide Composite: Manufacture, Morphology, Structure, Antistatic and Fireproof Properties

Directory of Open Access Journals (Sweden)

Jihui LI

2014-09-01

Full Text Available Graphite intercalation compounds (GIC and exfoliated graphite (EG as raw materials were prepared with flake graphite, concentrated sulphuric acid (H2SO4, potassium bichromate (K2Cr2O7 and peracetic acid (CH3CO3H and characterized. Then, high-density polyethylene-exfoliated graphite (HDPE-EG composites were fabricated with HDPE and EG via in situ synthesis technique in the different mass ratio, and their resistivity values (ohms/sq were measured. Based on the resistivity values, it was discovered that HDPE-EG composite with the antistatic property could be fabricated while the mass ratio was 5.00 : 0.30. Last, HDPE-EG-aluminium hydroxide (HDPE-EG-Al(OH3 composites were manufactured with HDPE, GIC and Al(OH3 via the in situ synthesis-thermal expansion technique, and their resistivity values and limiting oxygen index (LOI values were measured. Based on the resistivity values and LOI values, it was discovered that HDPE-EG-Al(OH3 composite with the antistatic and fireproof property could be manufactured while HDPE, GICs and Al(OH3 of mass ratio was 5.00 : 0.30 : 1.00. Otherwise, the petal-like morphology and structure of HDPE-EG-Al(OH3 composite were characterized, which consisted of EG, HDPE and Al(OH3. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.4275

Novel package for inhibition of aluminium corrosion in alkaline solutions

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M., E-mail: ashrafmoustafa@yahoo.com [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt); Khamis, E.; Abo-Eldahab, H.; Adeel, Sh. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)

2010-11-01

Inhibition of aluminium corrosion in 2 M sodium hydroxide solution by a package composed of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and lupine seed extract has been investigated employing different electrochemical techniques and chemical gasometry measurements. Potentiodynamic polarization curve measurements showed that lupine seed extract controls both the anodic dissolution of aluminium and the hydrogen gas evolved at the cathodic sites of aluminium surface. Nyquist plots showed two capacitive semicircles in the high and low frequency regions separated by an inductive loop at intermediate frequencies. The inductive loop may be explained by the occurrence of adsorbed intermediates on the surface. A proposed equivalent circuit was used to analyse the impedance spectra for aluminium in NaOH solutions. The corrosion inhibition data have been analysed using different isotherms. The results showed excellent agreement between the kinetic-thermodynamic model and Flory-Huggins isotherm. Gasometry measurements showed that the Inhibitive effect of the surfactant increases at a composition around its critical micelle concentration (cmc). The presence of both the surfactant and lupine seed extract did not indicate synergistic action between them. The mode of adsorption of the surfactant molecules corresponding to their structure is also discussed.

Novel package for inhibition of aluminium corrosion in alkaline solutions

International Nuclear Information System (INIS)

Abdel-Gaber, A.M.; Khamis, E.; Abo-Eldahab, H.; Adeel, Sh.

2010-01-01

Inhibition of aluminium corrosion in 2 M sodium hydroxide solution by a package composed of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and lupine seed extract has been investigated employing different electrochemical techniques and chemical gasometry measurements. Potentiodynamic polarization curve measurements showed that lupine seed extract controls both the anodic dissolution of aluminium and the hydrogen gas evolved at the cathodic sites of aluminium surface. Nyquist plots showed two capacitive semicircles in the high and low frequency regions separated by an inductive loop at intermediate frequencies. The inductive loop may be explained by the occurrence of adsorbed intermediates on the surface. A proposed equivalent circuit was used to analyse the impedance spectra for aluminium in NaOH solutions. The corrosion inhibition data have been analysed using different isotherms. The results showed excellent agreement between the kinetic-thermodynamic model and Flory-Huggins isotherm. Gasometry measurements showed that the Inhibitive effect of the surfactant increases at a composition around its critical micelle concentration (cmc). The presence of both the surfactant and lupine seed extract did not indicate synergistic action between them. The mode of adsorption of the surfactant molecules corresponding to their structure is also discussed.

TEM investigation of aluminium containing precipitates in high aluminium doped silicon carbide

International Nuclear Information System (INIS)

Wong-Leung, J.; FitzGerald, J.D.

2002-01-01

Full text: Silicon carbide is a promising semiconductor material for applications in high temperature and high power devices. The successful growth of good quality epilayers in this material has enhanced its potential for device applications. As a novel semiconductor material, there is a need for studying its basic physical properties and the role of dopants in this material. In this study, silicon carbide epilayers were grown on 4H-SiC wafers of (0001) orientation with a miscut angle of 8 deg at a temperature of 1550 deg C. The epilayers contained regions of high aluminium doping well above the solubility of aluminium in silicon carbide. High temperature annealing of this material resulted in the precipitation of aluminium in the wafers. The samples were analysed by secondary ion mass spectrometry and transmission electron microscopy. Selected area diffraction studies show the presence of aluminium carbide and aluminium silicon carbide phases. Copyright (2002) Australian Society for Electron Microscopy Inc

Numerical modeling of aluminium foam on two scales

Czech Academy of Sciences Publication Activity Database

Němeček, J.; Denk, F.; Zlámal, Petr

Roč. 267, September (2015), s. 506-516 ISSN 0096-3003 R&D Projects: GA ČR(CZ) GAP105/12/0824 Institutional support: RVO:68378297 Keywords : closed-cell aluminium foam * Alporas * multiscale modeling * homogenization * FFT * finite element modeling Subject RIV: JI - Composite Materials Impact factor: 1.345, year: 2015 http://www.sciencedirect.com/science/article/pii/S0096300315001162

Complexation efficiency of differently fixed 8-hydroxyquinoline and salicylic acid ligand groups for labile aluminium species determination in soils-comparison of two methods

International Nuclear Information System (INIS)

Matus, Peter; Kubova, Jana

2006-01-01

Two methods utilizing the complexation of labile Al species by 8-hydroxyquinoline (HQN) and salicylic acid (SA) ligand groups were developed for aluminium operationally defined fractionation in acid soils. First, the solid phase extraction (SPE) procedure by a short-term ion-exchange batch reaction with chelating resins Iontosorb Oxin and Iontosorb Salicyl containing both ligand groups was used previously. Second, the 8-hydroxyquinoline, salicylic acid and ammonium salicylate agents with different concentrations by a single extraction protocol were applied in this paper. The flame atomic absorption spectrometry (FAAS) and optical emission spectrometry with inductively coupled plasma were used for aluminium quantification. The comparison of results from both methods show the possibility to supersede the first laborious method for the second simpler one in Al environmental risk assessment. The use of 1% 8-hydroxyquinoline in 2% acetic acid and 0.2% salicylic acid by a single extraction protocol without a need of sample filtration can supersede the SPE procedure in the Al pollution soil monitoring. Finally, the new scheme usable in a laboratory and moreover, directly in a field was proposed for Al fractionation in solid and liquid environmental samples. The labile Al species in soils and sediments are separated after their single leaching by 8-hydroxyquinoline or salicylic acid without a need of sample filtration. The labile Al species in soil solutions and natural waters are separated after their ultrafiltration followed by the SPE procedure with Iontosorb Oxin or Iontosorb Salicyl

Adsorptivity of uranium by aluminium-activated carbon composite adsorbent

International Nuclear Information System (INIS)

Katoh, Shunsaku; Sugasaka, Kazuhiko; Fujii, Ayako; Takagi, Norio; Miyai, Yoshitaka

1976-01-01

To research the adsorption process of uranium from sea water by aluminium-activated carbon composite adsorbent (C-Al-OH), the authors examined the effects of temperature, pH and carbonate ion concentration of the solution upon the adsorption of uranium, using sodium chloride solution and natural sea water. The continued mixing of the solution for the duration of two to four hours was required to attain the apparent equilibrium of adsorption. The adsorption velocity at an early stage and the uptake of uranium at the final stage showed an increase in proportion to a rise in the adsorption temperature. In the experiment of adsorption for which sodium chloride solution was used, the linear relationship between the logarithm of the distribution coefficient (K sub(d)) and the pH of the solution was recognized. The uptake of the uranium from the solution at the pH of 12 increased as the carbonate ion concentration in the solution decreased. The uranyl ion in the natural sea water was assumed to be uranyl carbonate complex ion (UO 2 (CO 3 ) 3 4- ). As the result of the calculation conducted by using the formation constants for uranyl complexes in literature, it was found that uranyl hydroxo complex ion (UO 2 (OH) 3 - ) increased in line with a decrease of the carbonate ion concentration in the solution. The above results of the experiment suggested that the adsorption of uranium by the adsorbent (C-Al-OH) was cationic adsorption or hydrolysis adsorption being related with the active proton on the surface of the adsorbent. (auth.)

A Fundamental Approach to Developing Aluminium based Bulk Amorphous Alloys based on Stable Liquid Metal Structures and Electronic Equilibrium - 154041

Science.gov (United States)

2017-03-28

AFRL-AFOSR-JP-TR-2017-0027 A Fundamental Approach to Developing Aluminium -based Bulk Amorphous Alloys based on Stable Liquid-Metal Structures and...to 16 Dec 2016 4.  TITLE AND SUBTITLE A Fundamental Approach to Developing Aluminium -based Bulk Amorphous Alloys based on Stable Liquid-Metal...Air Force Research Laboratory for accurately predicting compositions of new amorphous alloys specifically based on aluminium with properties superior

Analysis of aluminium in rat following administration of allergen immunotherapy using either aluminium or microcrystalline-tyrosine-based adjuvants.

Science.gov (United States)

McDougall, Stuart A; Heath, Matthew D; Kramer, Matthias F; Skinner, Murray A

2016-03-01

Investigation into the absorption, distribution and elimination of aluminium in rat after subcutaneous aluminium adjuvant formulation administration using ICP-MS is described. Assays were verified under the principles of a tiered approach. There was no evidence of systemic exposure of aluminium, in brain or in kidney. Extensive and persistent retention of aluminium at the dose site was observed for at least 180 days after administration. This is the first published work that has quantified aluminium adjuvant retention based on the quantity of aluminium delivered in a typical allergy immunotherapy course. The results indicate that the repeated administration of aluminium-containing adjuvants will likely contribute directly and significantly to an individual's body burden of aluminium.

TITANIUM CARBON ALUMINIUM : A NOVEL GRAIN REFINER FOR ALUMINIUM-LITHIUM ALLOYS

OpenAIRE

Birch , M.; Cowell , A.

1987-01-01

This work explores the possibility of achieving grain size control in aluminium-lithium alloys with the titanium carbon aluminium (TiCAl) master alloys invented at the Technical University of Berlin and developed by London and Scandinavian Metallurgical Co Ltd (LSM). Grain refining tests were conducted on a single batch of 8090 alloy using addition rates of 0.2wt% and 0.4wt% of TiCAl and 3/1 titanium boron aluminium (TiBAl). Other tests using 0.4wt% of binary TiAl gave poor results, showing t...

Thermoluminescence study of aluminium oxide doped germanium prepared by combustion synthesis method

Directory of Open Access Journals (Sweden)

Saharin Nurul Syazlin Binti

2017-01-01

Full Text Available The present paper reports the optimum concentration of germanium (Ge dopant in aluminium oxide (AhO3 samples prepared by combustion synthesis (CS method for thermoluminescence (TL studies. The samples were prepared at various Ge concentration i.e. 1 to 5% mol. The phase formation of un-doped and Ge-doped Al2O3 samples was determined using X-ray Diffraction (XRD. The sharp peaks present in the XRD pattern confirms the crystallinity of the samples. The samples were then exposed to 50 Gy Cobalt-60 sources (Gamma cell 220. TL glow curves were measured and recorded using a Harshaw Model 3500 TLD reader. Comparison of TL peaks were observed to obtain the best composition of Ge dopants. A simple glow curves TL peak at around 175̊C for all composition samples was observed. It was also found that the composition of aluminium oxide doped with 3.0% of germanium exhibits the highest thermoluminescence (TL intensity which is 349747.04 (a.u.

Aluminium in Infrastructures

NARCIS (Netherlands)

Maljaars, J.

2016-01-01

Aluminium alloys are used in infrastructures such as pedestrian bridges or parts of it such as handrail. This paper demonstrates that aluminium alloys are in principle also suited for heavy loaded structures, such as decks of traffic bridges and helicopter landing platforms. Recent developments in

Formation of aluminium nitride and segregation of Cu impurity atoms in aluminium implanted by high dose nitrogen ions

International Nuclear Information System (INIS)

Lin Chenglu; Hemment, P.L.F.; Li Jinhua; Zou Shichang

1994-01-01

Aluminium films with a thickness of 7000 A (containing 0.85% copper) were deposited on silicon substrates. 400 keV N 2 + or 350 keV N + ions were implanted into the aluminium films or at the interface between the aluminium and silicon, respectively. Automatic spreading resistance (ASR), Fourier transform infrared spectroscopy (FTIR) and Rutherford backscattering (RBS) and channelling were used to characterize the formation of aluminium nitride and the depth distribution of the Cu impurity in the aluminium films after ion implantation and post-annealing. The formation of a stoichiometric AlN layer with high resistance was evident from ASR, RBS analysis and FTIR measurements by the presence of the absorption band at 650 cm -1 . When the implanted nitrogen is near the interface between the aluminium and silicon, a multilayer structure can be obtained, which consists of aluminium, aluminium nitride and the silicon substrate. Cu, which is a background impurity in the deposited aluminium films, segregated into the synthesised aluminium nitride during high dose nitrogen ion implantation. This is due to irradiation-induced segregation during ion implantation. (orig.)

Ion nitriding of aluminium

International Nuclear Information System (INIS)

Fitz, T.

2002-09-01

The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma immersion ion implantation, which are methods with a potential for industrial application. (orig.)

FIB-SEM investigation of trapped intermetallic particles in anodic oxide films on AA1050 aluminium

DEFF Research Database (Denmark)

Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.

2011-01-01

-containing intermetallic particles incorporated into the anodic oxide films on industrially pure aluminium (AA1050, 99.5 per cent) has been investigated. AA1050 aluminium was anodized in a 100?ml/l sulphuric acid bath with an applied voltage of 14?V at 20°C ±2°C for 10 or 120?min. The anodic film subsequently was analyzed......Purpose - The purpose of this investigation is to understand the structure of trapped intermetallics particles and localized composition changes in the anodized anodic oxide film on AA1050 aluminium substrates. Design/methodology/approach - The morphology and composition of Fe......-shaped particles were embedded in the anodic oxide film as a thin strip structure and located near the top surface of the film, whereas the round-shaped particles were trapped in the film with a spherical structure, but partially dissolved and were located throughout the thickness of the anodic film. The Fe...

Coefficient of friction and wear rate effects of different composite nanolubricant concentrations on Aluminium 2024 plate

Science.gov (United States)

Zawawi, N. N. M.; Azmi, W. H.; Redhwan, A. A. M.; Sharif, M. Z.

2017-10-01

Wear of sliding parts and operational machine consistency enhancement can be avoided with good lubrication. Lubrication reduce wear between two contacting and sliding surfaces and decrease the frictional power losses in compressor. The coefficient of friction and wear rate effects study were carried out to measure the friction and anti-wear abilities of Al2O3-SiO2 composite nanolubricants a new type of compressor lubricant to enhanced the compressor performances. The tribology test rig employing reciprocating test conditions to replicate a piston ring contact in the compressor was used to measure the coefficient of friction and wear rate. Coefficient of friction and wear rate effects of different Al2O3-SiO2/PAG composite nanolubricants of Aluminium 2024 plate for 10-kg load at different speed were investigated. Al2O3 and SiO2 nanoparticles were dispersed in the Polyalkylene Glycol (PAG 46) lubricant using two-steps method of preparation. The result shows that the coefficient friction and wear rate of composite nanolubricants decreased compared to pure lubricant. The maximum reduction achievement for friction of coefficient and wear rate by Al2O3-SiO2 composite nanolubricants by 4.78% and 12.96% with 0.06% volume concentration. Therefore, 0.06% volume concentration is selected as the most enhanced composite nanolubricants with effective coefficient of friction and wear rate reduction compared to other volume concentrations. Thus, it is recommended to be used as the compressor lubrication to enhanced compressor performances.

Variation in aluminium patch test reactivity over time.

Science.gov (United States)

Siemund, Ingrid; Mowitz, Martin; Zimerson, Erik; Bruze, Magnus; Hindsén, Monica

2017-11-01

Contact allergy to aluminium has been reported more frequently in recent years. It has been pointed out that positive patch test reactions to aluminium may not be reproducible on retesting. To investigate possible variations in patch test reactivity to aluminium over time. Twenty-one adults, who had previously reacted positively to aluminium, were patch tested with equimolar dilution series in pet. of aluminium chloride hexahydrate and aluminium lactate, four times over a period of 8 months. Thirty-six of 84 (43%) serial dilution tests with aluminium chloride hexahydrate and 49 of 84 (58%) serial dilution tests with aluminium lactate gave negative results. The range of reactivity varied between a negative reaction to aluminium chloride hexahydrate at 10% and/or to aluminium lactate at 12%, and a positive reaction to aluminium chloride hexahydrate at 0.1% and/or to aluminium lactate at 0.12%. The highest individual difference in test reactivity noticed was 320-fold when the two most divergent minimal eliciting concentrations were compared. The patch test reactivity to aluminium varies over time. Aluminium-allergic individuals may have false-negative reactions. Therefore, retesting with aluminium should be considered when there is a strong suspicion of aluminium contact allergy. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Buffering effects on electrograining of aluminium in nitric acid

International Nuclear Information System (INIS)

Koroleva, E.V.; Thompson, G.E.; Skeldon, P.; Hollrigl, G.; Lockwood, S.; Smith, G.

2005-01-01

Electrograining of a binary Al-Si alloy has been undertaken in nitric acid based electrolytes, with the resultant surfaces examined by scanning and transmission electron microscopies. Depending on electrograining conditions, the pit appearance varies from hemispherical to large lateral pits, with the latter favoured in relatively acidic electrolytes. The conditions prevailing in the pit have been explored through use of aluminium ion additions to the nitric acid electrolyte as well as additions of species which influence the precipitation and dissolution of aluminium hydroxide. These confirm that control of the pit solution pH, through hydroxide generation, as a result of the selected electrograining conditions and consequent anodic and cathodic polarisation, enables tailoring of the resultant electrograined surface appearance

Vegetation composition and structure influences bird species ...

African Journals Online (AJOL)

Vegetation composition and structure influences bird species community ... variables on bird species diversity and richness of respective foraging guilds, and ... of the species assessed: (1) increasing closed cover due to woody plant density, ...

Research and development of advanced aluminium/graphite composites for thermal management applications

CERN Document Server

Wyszkowska, Edyta; Bertarelli, Alessandro

Thermal management materials are continuously gaining importance as a consequence of everlasting evolution in performance of electronic and electric devices. In particular, by improving the heat exchanger’s materials' properties (i.e. thermal conductivity) it is possible to boost further performance and miniaturization of such devices. Due to their high thermal conductivity, Copper and Aluminium are currently the most commonly used materials for thermal management applications. However, the mismatch in thermal expansion between Cooper/Aluminium and Silicon is limiting the heat transfer at the interface between the electronic chip and the heat exchanger. Furthermore, Copper is indeed characterized by a high thermal conductivity but at the same time its high density (8.9 g/cm3) increases weight of the final product, which in most of the cases does not meet specific application requirements. High cost of these materials is another constraint which limits their application. Due to aforementioned facts, monolith...

Statistical model to predict dry sliding wear behaviour of Aluminium-Jute bast ash particulate composite produced by stir-casting

Directory of Open Access Journals (Sweden)

Gambo Anthony VICTOR

2017-06-01

Full Text Available A model to predict the dry sliding wear behaviour of Aluminium-Jute bast ash particulate composites produced by double stir-casting method was developed in terms of weight fraction of jute bast ash (JBA. Experiments were designed on the basis of the Design of Experiments (DOE technique. A 2k factorial, where k is the number of variables, with central composite second-order rotatable design was used to improve the reliability of results and to reduce the size of experimentation without loss of accuracy. The factors considered in this study were sliding velocity, sliding distance, normal load and mass fraction of JBA reinforcement in the matrix. The developed regression model was validated by statistical software MINITAB-R14 and statistical tool such as analysis of variance (ANOVA. It was found that the developed regression model could be effectively used to predict the wear rate at 95% confidence level. The wear rate of cast Al-JBAp composite decreased with an increase in the mass fraction of JBA and increased with an increase of the sliding velocity, sliding distance and normal load acting on the composite specimen.

The distribution and phylogeny of aluminium accumulating plants in the Ericales

NARCIS (Netherlands)

Jansen, S.; Watanabe, T.; Caris, P.; Geuten, K.; Lens, F.; Pyck, N.; Smets, E.

2004-01-01

The distribution of aluminium (Al) accumulation in the Ericales is surveyed, based on semi-quantitative tests of 114 species and literature data. Al accumulation mainly characterises the families Diapensiaceae, Pentaphylacaceae, Symplocaceae, Ternstroemiaceae, and Theaceae. Al accumulation is

Improvement of hardness of aluminium AA1200 by laser surface alloying

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-07-01

Full Text Available Aluminium is vastly used in industry due to its low cost, light weight and excellent workability, but lacks in wear resistance and hardness. Laser alloying is used to improve the surface properties such as hardness by modifying the composition...

Microstructural characteristics, mechanical and wear behaviour of aluminium matrix hybrid composites reinforced with alumina, rice husk ash and graphite

Directory of Open Access Journals (Sweden)

Kenneth Kanayo Alaneme

2015-09-01

Full Text Available The microstructural characteristics, mechanical and wear behaviour of Aluminium matrix hybrid composites reinforced with alumina, rice husk ash (RHA and graphite were investigated. Alumina, RHA and graphite mixed in varied weight ratios were utilized to prepare 10 wt% hybrid reinforced Al-Mg-Si alloy based composites using two-step stir casting. Hardness, tensile properties, scanning electron microscopy, and wear tests were used to characterize the composites produced. The results show that Hardness decreases with increase in the weight ratio of RHA and graphite in the composites; and with RHA content greater than 50%, the effect of graphite on the hardness becomes less significant. The tensile strength for the composites containing o.5wt% graphite and up to 50% RHA was observed to be higher than that of the composites without graphite. The toughness values for the composites containing 0.5wt% graphite were in all cases higher than that of the composites without graphite. The % Elongation for all composites produced was within the range of 10–13% and the values were invariant to the RHA and graphite content. The tensile fracture surface morphology in all the composites produced was identical characterized with the presence of reinforcing particles housed in ductile dimples. The composites without graphite exhibited greater wear susceptibility in comparison to the composite grades containing graphite. However the wear resistance decreased with increase in the graphite content from 0.5 to 1.5 wt%.

Recovery in aluminium

DEFF Research Database (Denmark)

Gundlach, Carsten

2006-01-01

In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

Application of aluminium in nuclear power plants; the role of corrosion under breakdown conditions within the hermetic zone

International Nuclear Information System (INIS)

Szontagh, Endre; Eva, Andras; Koevari, Tiborne

1987-01-01

Basic corrosion processes of aluminium determining the application possibilities as construction material within the containment of nuclear power plants were studied. The structure and stability of the oxide layers formed on aluminium surfaces depend on the pH, the temperature and the composition of the media and on the presence of alloying elements in the metal. It could be stated that hydrogen evolution due to the corrosion interaction of aluminium with the coolant of WWER-type reactors was less significant than calculated values. (V.N.)

Fatty acid composition of forage herb species

DEFF Research Database (Denmark)

Warner, D.; Jensen, Søren Krogh; Cone, J.W.

2010-01-01

The use of alternative forage species in grasslands for intensive livestock production is receiving renewed attention. Data on fatty acid composition of herbs are scarce, so four herbs (Plantago lanceolata, Achillea millefolium, Cichorium intybus, Pastinaca sativa) and one grass species (timothy......, Phleum pratense) were sown in a cutting trial. The chemical composition and concentration of fatty acids (FA) of individual species were determined during the growing season. Concentrations of crude protein and FA were generally higher in the herbs than in timothy. C. intybus had the highest nutritive...

Internal friction in iron-aluminium alloys having a high aluminium content

International Nuclear Information System (INIS)

Hillairet, J.; Delaplace, J.; Silvent, A.

1966-01-01

By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author) [fr

The effect of surface treatment and gaseous rust protection paper on the atmospheric corrosion stability of aluminium alloy

International Nuclear Information System (INIS)

Gao Guizhong

1992-03-01

The experimental results of atmospheric corrosion of 166 aluminium alloy of Al-Mg-Si-Cu system and 167 aluminium alloy of Al-Mg-Si-Cu-Fe-Ni system for different surface treatment and different wrapping papers used are introduced. The results show: 1. The composition of aluminium alloy has some effect on the performance of atmospheric corrosion stability and the local corrosion depth for 167 aluminium alloy specimen is considerable. 2. After 8 years storage, the 167 aluminium alloy tubular specimen, which was treated with surface treatment in deionized water at 100 ∼ 230 C degree, has no spot of atmospheric corrosion found. 3. Within the test period, the performance of atmospheric corrosion stability by sulphuric-acid anodization film is remarkable. 4. The No. 19 gaseous rust protection paper has no effect of atmospheric corrosion stability on the 166 and 167 aluminium alloys which were treated with quenching and natural ageing method

Study through potentiodynamic techniques of the corrosion resistance of different aluminium base MMC's with boron additions

International Nuclear Information System (INIS)

Abenojar, J.; Bautista, A.; Guzman, S.; Velasco, F.; Martinez, M.A.

2009-01-01

This paper compares a wrought aluminium with a PM aluminium and PM aluminium alloys with boron-base additions, containing boron carbide and Fe/B (obtained by mechanical alloying during 36 hours from a Fe-B 50% mixture by weight). The effect of sintering temperature for the Fe/B containing material and the effect of mechanical alloying for the boron carbide containing aluminium alloy on the corrosion resistance of those materials have been studied. Their behaviour is followed through cyclic anodic polarization curves in chloride media. In the Al+20%Fe/B composite, low sintering temperatures (650- 950 deg C) exert a negative effect. However, when the material was sintered at high temperature (1000-1100 deg C) its behaviour was very similar to the PM pure aluminium. The effect of mechanical alloying studied in aluminium with boron carbide was also important in corrosion resistance, finding a lower corrosion rate in the mechanically alloyed material. (author)

Theoretical study of the lowest-lying electronic states of Aluminium monoiodide

International Nuclear Information System (INIS)

Taher, F.; Kabbani, A.; Ani-El Houte, W.

2004-01-01

Full text.The spectroscopic study of Aluminium monohalides, especially the Aluminium monoiodide, is important for monitoring such species in high temperature fast-flow reactors. Theoretical calculations of AlI are not available, whereas several studies have been done for the other aluminium monohalides. In this work, CAS-SCF/MRCI calculations are performed for the lowest-lying electronic states of AlI in a range of internuclear distance between 2.30 A and 2.80 A. Ab-initio calculations have been effectuated by using the computational chemistry program Molpro. The basis set used in this study for aluminium atom is that used by Langhoff for aluminium monohalides, of contractions using atomic natural orbitals and a pseudopotential is used for iode. Accurate theoretical spectroscopic constants and potential curves are obtained for the ground state X 1 Σ + and the first excited states a 3 Π and A 1 Π. The calculated values of Te, ωe, ωexe and re of these states are compatible with the experimental results. An ordering of states is represented for the lowest five predicted singlet and lowest five predicted triplet states. These results provide a big support to determine the analogy in the ordering of the electronic states in AlF, AlBr and AlI respectively at lower energies. These theoretical results identify a set of electronic singlet and triplet states unobserved experimentally

Enhancement of wear and ballistic resistance of armour grade AA7075 aluminium alloy using friction stir processing

Directory of Open Access Journals (Sweden)

I. Sudhakar

2015-03-01

Full Text Available Industrial applications of aluminium and its alloys are restricted because of their poor tribological properties. Thermal spraying, laser surfacing, electron beam welding are the most widely used techniques to alter the surface morphology of base metal. Preliminary studies reveal that the coating and layering of aluminium alloys with ceramic particles enhance the ballistic resistance. Furthermore, among aluminium alloys, 7075 aluminium alloy exhibits high strength which can be compared to that of steels and has profound applications in the designing of lightweight fortification structures and integrated protection systems. Having limitations such as poor bond integrity, formation of detrimental phases and interfacial reaction between reinforcement and substrate using fusion route to deposit hard particles paves the way to adopt friction stir processing for fabricating surface composites using different sizes of boron carbide particles as reinforcement on armour grade 7075 aluminium alloy as matrix in the present investigation. Wear and ballistic tests were carried out to assess the performance of friction stir processed AA7075 alloy. Significant improvement in wear resistance of friction stir processed surface composites is attributed to the change in wear mechanism from abrasion to adhesion. It has also been observed that the surface metal matrix composites have shown better ballistic resistance compared to the substrate AA7075 alloy. Addition of solid lubricant MoS2 has reduced the depth of penetration of the projectile to half that of base metal AA7075 alloy. For the first time, the friction stir processing technique was successfully used to improve the wear and ballistic resistances of armour grade high strength AA7075 alloy.

The determination of trace oxygen in aluminium and aluminium-silicon alloy by helium-3 activation analysis

International Nuclear Information System (INIS)

Vandecasteele, C.; Goethals, P.; Kieffer, R.; Hoste, J.

1975-01-01

The determination of oxygen in aluminium and aluminium-silicon alloy by helium-3 activation is studied. The 18 F formed from oxygen is separated by distillation followed by precipitation of leadfluorochloride. The chemical yield is determined by activation in an isotopic neutron source. Concentrations of resp. 27 and 64 ng.g -1 with a precision for a single determination of resp. 30 and 13% are found in 99.5% aluminium and in aluminium-silicon (3%) alloy. (author)

Roll bonding of strained aluminium

DEFF Research Database (Denmark)

Staun, Jakob M.

2003-01-01

This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

Aluminium in foodstuffs and diets in Sweden.

Science.gov (United States)

Jorhem, L; Haegglund, G

1992-01-01

The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources.

Constructions of aluminium electrolytic cells

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter of monograph is devoted to constructions of aluminium electrolytic cells. Therefore, the general characteristic and classification of aluminium electrolytic cells was considered. The anode and cathode structure was studied. The lining of cathode casing, the process of collection of anode gases, electrolytic cell cover, and electrical insulation was studied as well. The installation and dismantling of aluminium electrolytic cells was described.

Optically Designed Anodised Aluminium Surfaces: Microstructural and Electrochemical Aspects

DEFF Research Database (Denmark)

Gudla, Visweswara Chakravarthy

is not possible as the anodic pore sizes are an order of magnitude smaller than the traditional white pigments. The approaches presented in this thesis focus on different techniques like modification of the aluminium microstructure, engineering of the aluminium surface, and application on non...... the microstructure in order to impart light scattering ability to the anodised layer. Coatings based on Al-Zr and Al-Ti binary system were studied for their anodising behaviour with and without heat treatment. The structure evolution of the Al-Zr sputtered coatings and the effect of Si during heat treatment...... Emission Spectroscopy, and Scanning Kelvin Probe Force Microscopy. Optical characterization was performed using integrating sphere measurements. Combining the results and understanding obtained from anodising of magnetron sputtered coatings, Al-TiO2 surface composites and their electrochemical behaviour...

Aluminium hydro(oxide)–based (AO) adsorbent for defluoridation of ...

African Journals Online (AJOL)

High resolution 27Al Magic Angle Spinning Nuclear Magnetic Resonance (27Al MAS NMR) spectra of AO, AA, and PB were recorded, to analyse the coordination geometry of solid Al species and the results showed that aluminium is coordinated octahedrally and tetrahedrally in all cases. Regeneration experiments showed ...

Synthesis of nano-crystalline zirconium aluminium oxynitride (ZrAlON) composite films by dense plasma Focus device

Energy Technology Data Exchange (ETDEWEB)

Khan, I.A.; Hassan, M.; Hussain, T. [Department of Physics, GC University, 54000 Lahore (Pakistan); Ahmad, R., E-mail: ahriaz@gmail.com [Department of Physics, GC University, 54000 Lahore (Pakistan); Zakaullah, M. [Department of Physics, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Rawat, R.S. [National Institute of Education, Nanyang Technological University, Singapore 637616 (Singapore)

2009-04-01

Zirconium aluminium oxynitride multiphase composite film is deposited on zirconium substrate using energetic nitrogen ions delivered from dense plasma Focus device. X-ray diffractometer (XRD) results show that five Focus shots are sufficient to initiate the nucleation of ZrN and Al{sub 2}O{sub 3} whereas 10 Focus shots are sufficient to initiate the nucleation of AlN. XRD results reveal that crystal growth of nitrides/oxides increases by increasing Focus shots (up to 30 Focus shots) and resputtering of the previously deposited film is taken place by further increase in Focus shots (40 Focus shots). Scanning electron microscopic (SEM) results indicate the uniform distribution of spherical grains ({approx}35 nm). A smoother surface is observed for 20 Focus shots at 0 deg. angular position. SEM results also show a net-type microstructure (thread like features) of the sample treated for 30 Focus shots whereas rough surface morphology is observed for 40 Focus shots. Energy dispersive spectroscopic profiles show the distribution of different elements present in the deposited composite films. A typical microhardness value of the deposited composite films is 5255 {+-} 10 MPa for 10 grams imposed load which is 3.3 times than the microhardness values of unexposed sample. The microhardness values of the exposed samples increases with increasing Focus shots (up to 30 Focus shots) and decreases for 40 Focus shots treatment due to resputtering of the previously deposited composite film. The microhardness values of the composite films decreases by increasing the sample's angular position.

Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

Science.gov (United States)

Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

2011-11-01

The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling.

Bioaccumulation of metals by Rhodophyta species at Antikyra Gulf (Greece) near an aluminium factory

Energy Technology Data Exchange (ETDEWEB)

Malea, P. [Thessaloniki Univ. (Greece). Inst. of Botany; Haritonidis, S. [Thessaloniki Univ. (Greece). Inst. of Botany; Stratis, I. [Inst. of Analytical Chemistry, School of Chemistry, Thessaloniki (Greece)

1994-11-01

The bioaccumulation of Fe, Cu, Zn, Cd, Pb, Na, K, Ca and Mg by seven species of red algae (Rhodophyta) was studied after their seasonal collection from 9 stations in Antikyra Gulf (Greece). This area is characterized by its bauxite substrate and the discharge of wastes from an aluminium factory. Corallina elongata, Jania rubens and Liagora viscida showed elevated concentrations of Cu, Na and Mg and low Fe, Na and K concentrations, whereas Pterosiphonia complanata, Laurencia obtusa and Vidalia volubilis displayed entirely contrary behaviour. These interspecific differences are discussed in relation to morphology, ecology, plant structure and the binding sites available on the algae. Among the nine metals, only Cd concentrations in P. complanata showed significantly positive correlation with the respective concentrations in the sediment; no metal in L. obtusa and P. complanata showed a significant correlation with the concentrations of the dissolved metals in seawater. Significant positive or negative correlations with the concentrations of several metals in L. obtusa and P. complanata were also observed, which may be attributed to metal interactions in binding to plant tissues. The concentrations of Fe, Cu, Zn, K, Na and Ca in Laurencia obtusa were higher in summer or autumn; Pb and Mg followed an opposite pattern of seasonal variation, whereas Cd levels were higher in spring and summer. The red algae of Antikyra Gulf generally exhibited higher Fe, Ca, Cu, Cd and Pb concentrations than those of similar species from other geographical areas. (orig.)

[Association between serum aluminium level and methylation of amyloid precursor protein gene in workers engaged in aluminium electrolysis].

Science.gov (United States)

Yang, X J; Yuan, Y Z; Niu, Q

2016-04-20

To investigate the association between serum aluminium level and methylation of the promoter region of amyloid precursor protein (APP)gene in workers engaged in aluminium electrolysis. In 2012, 366 electrolysis workers in an aluminium factory were enrolled as exposure group (working years >10 and age >40 years)and divided into low-exposure group and high-exposure group based on the median serum aluminium level. Meanwhile, 102 workers in a cement plant not exposed to aluminium were enrolled as control group. Graphite furnace atomic absorption spectrometry was used to measure serum aluminium level, methylation specific PCR was used to measure the methylation rate of the promoter region of APP gene, and ELI-SA was used to measure the protein expression of APP in lymphocytes in peripheral blood. The exposure group had a significantly higher serum aluminium level than the control group (45.07 μg/L vs 30.51 μg/L, P0.05). The multivariate logistic regression analysis showed that with reference to the control group, low aluminium exposure (OR=1.86, 95% CI 1.67~3.52)and high aluminium exposure (OR=2.98, 95% CI 1.97~4.15)were risk factors for a reduced methylation rate of the promoter region of APP gene. Reduced methylation of the promoter region of APP gene may be associated with increased serum aluminium level, and downregulated methylation of the promoter region of APP gene may accelerate APP gene transcription.

Development of multilayer coatings for forming dies and tools of aluminium alloy from liquid state

International Nuclear Information System (INIS)

Torres, E; Ugues, D; Brytan, Z; Perucca, M

2009-01-01

In this work, a nanocomposite (Cr,Al) x N 1-x /Si 3 N 4 coating system was deposited on H11 hot work tool steel, using the Lateral Arc Rotating Cathodes (LARC (registered) ) deposition system and modulating the chemical composition of the chromium and aluminium-silicon content. Structural characterizations were performed using scanning electron microscopy, equipped with energy dispersive spectroscopy probe, and applying x-ray diffraction, for the evaluation of phase constitution and crystallite size. In addition to the structural features, the coatings' resistance to cyclic immersions in molten aluminium alloy was evaluated. The deposited CrAlSiN coatings exhibited an fcc-Cr 1-x Al x N type structure with different aluminium contents, which directly influence hardness and wear and fatigue resistance in cyclic immersion tests. The main failure modes that occurred on the coatings' surface were soldering and thermal fatigue cracks mainly in the form of heat checks. The aluminium rich coatings were able to withstand about 15 000 cycles, whereas the decrease in the aluminium content in the coatings results in a decrease in the resistance to the immersion in molten aluminium bath. It is worthwhile to note that uncoated H11, subjected to similar testing conditions, withstood at maximum 5000 cycles.

Polymer composite adsorbents using particles of molecularly imprinted polymers or aluminium oxide nanoparticles for treatment of arsenic contaminated waters.

Science.gov (United States)

Önnby, L; Pakade, V; Mattiasson, B; Kirsebom, H

2012-09-01

Removal of As(V) by adsorption from water solutions was studied using three different synthetic adsorbents. The adsorbents, (a) aluminium nanoparticles (Alu-NPs, polymers (polymer backbones of pure polyacrylamide (MIP-cryo) were of better stability than the amine containing polymer backbone (Alu-cryo). Both composites worked well in the studied pH range of pH 2-8. Adsorption tested in real wastewater spiked with arsenic showed that co-ions (nitrate, sulphate and phosphate) affected arsenic removal for Alu-cryo more than for MIP-cryo. Both composites still adsorbed well in the presence of counter-ions (copper and zinc) present at low concentrations (μg/l). The unchanged and selective adsorption in realistic water observed for MIP-cryo was concluded to be due to a successful imprinting, here controlled using a non-imprinted polymer (NIP). A development of MIP-cryo is needed, considering its low adsorption capacity. Copyright © 2012 Elsevier Ltd. All rights reserved.

Corrosion and electrochemical behavior of boron/aluminum composites

International Nuclear Information System (INIS)

Pohlman, S.L.

1976-01-01

The results of an investigation to determine the importance of galvanic corrosion as a mechanism for the interfacial attack in boron/aluminium composites are reported. The results indicated that galvanic corrosion occurred between the aluminium matrix and the aluminium boride intermetallic formed during fabrication at the matrix/filament interface. Electric current measurements revealed that the aluminium matrix was preferentially attacked and the interfacial boride was cathodically protected. 18 references

Bumblebee pupae contain high levels of aluminium.

Science.gov (United States)

Exley, Christopher; Rotheray, Ellen; Goulson, David

2015-01-01

The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

Long-term effects of aluminium dust inhalation.

Science.gov (United States)

Peters, Susan; Reid, Alison; Fritschi, Lin; de Klerk, Nicholas; Musk, A W Bill

2013-12-01

During the 1950s and 1960s, aluminium dust inhalation was used as a potential prophylaxis against silicosis in underground miners, including in Australia. We investigated the association between aluminium dust inhalation and cardiovascular, cerebrovascular and Alzheimer's diseases in a cohort of Australian male underground gold miners. We additionally looked at pneumoconiosis mortality to estimate the effect of the aluminium therapy. SMRs and 95% CI were calculated to compare mortality of the cohort members with that of the Western Australian male population (1961-2009). Internal comparisons on duration of aluminium dust inhalation were examined using Cox regression. Aluminium dust inhalation was reported for 647 out of 1894 underground gold miners. During 42 780 person-years of follow-up, 1577 deaths were observed. An indication of increased mortality of Alzheimer's disease among miners ever exposed to aluminium dust was found (SMR=1.38), although it was not statistically significant (95% CI 0.69 to 2.75). Rates for cardiovascular and cerebrovascular death were above population levels, but were similar for subjects with or without a history of aluminium dust inhalation. HRs suggested an increasing risk of cardiovascular disease with duration of aluminium dust inhalation (HR=1.02, 95% CI 1.00 to 1.04, per year of exposure). No difference in the association between duration of work underground and pneumoconiosis was observed between the groups with or without aluminium dust exposure. No protective effect against silicosis was observed from aluminium dust inhalation. Conversely, exposure to aluminium dust may possibly increase the risk of cardiovascular disease and dementia of the Alzheimer's type.

Design and analysis of aluminium brdiges

NARCIS (Netherlands)

Soetens, F.; Straalen, IJ.J. van

2004-01-01

Applications of aluminium have grown considerably in building and civil engineering the last decade, which is due to various aspects: light weight, durability and maintenance, use of extrusions. The paper starts with a short history of aluminium bridges and then focuses on aluminium bridges in the

[Effect of amount of silane coupling agent on flexural strength of dental composite resins reinforced with aluminium borate whisker].

Science.gov (United States)

Zhu, Ming-yi; Zhang, Xiu-yin

2015-06-01

To evaluate the effect of amount of silane coupling agent on flexural strength of dental composite resins reinforced with aluminium borate whisker (ABW). ABW was surface-treated with 0%, 1%, 2%, 3% and 4% silan coupling agent (γ-MPS), and mixed with resin matrix to synthesize 5 groups of composite resins. After heat-cured at 120 degrees centigrade for 1 h, specimens were tested in three-point flexure to measure strength according to ISO-4049. One specimen was selected randomly from each group and observed under scanning electron microscope (SEM). The data was analyzed with SAS 9.2 software package. The flexural strength (117.93±11.9 Mpa) of the group treated with 2% silane coupling agent was the highest, and significantly different from that of the other 4 groups (α=0.01). The amount of silane coupling agent has impact on the flexural strength of dental composite resins reinforced with whiskers; The flexual strength will be reduced whenever the amount is higher or lower than the threshold. Supported by Research Fund of Science and Technology Committee of Shanghai Municipality (08DZ2271100).

Recycling of aluminium swarf by direct incorporation in aluminium melts

OpenAIRE

Puga, Hélder; Barbosa, J.; Soares, Delfim; Silva, Filipe Samuel; Ribeiro, Carlos Silva

2009-01-01

The purpose of this work was to recover a standard AlSi12Cu1 alloy from machining chips inside the foundry plant, by using an environmentally friend technique to produce cast ingots with characteristics similar to those of the commercially available 2nd melt raw material. The recyclability of aluminium swarf using different melting techniques and the influence of chips preparation in the aluminium alloy recovery rate and dross production was experimentally studied and evaluated...

Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

DEFF Research Database (Denmark)

Henriksen, L.; Johansen, A.; Koch, J.

1968-01-01

Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produces...... rows of dislocation loops all lying parallel to one particular direction. If the aluminium target is quenched from 600 °C and annealed at room temperature prior to irradiation with aluminium ions, the rows of loops are suppressed. The amount of damage observed is considerably less than would...

Structural study of Al2O3-Na2O-CaO-P2O5 bioactive glasses as a function of aluminium content.

Science.gov (United States)

Smith, J M; King, S P; Barney, E R; Hanna, J V; Newport, R J; Pickup, D M

2013-01-21

Calcium phosphate based biomaterials are extensively used in the context of tissue engineering: small changes in composition can lead to significant changes in properties allowing their use in a wide range of applications. Samples of composition (Al(2)O(3))(x)(Na(2)O)(0.11-x)(CaO)(0.445)(P(2)O(5))(0.445), where x = 0, 0.03, 0.05, and 0.08, were prepared by melt quenching. The atomic-scale structure has been studied using neutron diffraction and solid state (27)Al MAS NMR, and these data have been rationalised with the determined density of the final glass product. With increasing aluminium concentration the density increases initially, but beyond about 3 mol. % Al(2)O(3) the density starts to decrease. Neutron diffraction data show a concomitant change in the aluminium speciation, which is confirmed by (27)Al MAS NMR studies. The NMR data reveal that aluminium is present in 4, 5, and 6-fold coordination and that the relative concentrations of these environments change with increasing aluminium concentration. Materials containing aluminium in 6-fold coordination tend to have higher densities than analogous materials with the aluminium found in 4-fold coordination. Thus, the density changes may readily be explained in terms of an increase in the relative concentration of 4-coordinated aluminium at the expense of 6-fold aluminium as the Al(2)O(3) content is increased beyond 3 mol. %.

Laser welding of aluminium alloys

OpenAIRE

Forsman, Tomas

2000-01-01

This thesis treats laser welding of aluminium alloys from a practical perspective with elements of mathematical analysis. The theoretical work has in all cases been verified experimentally. The aluminium alloys studied are from the 5xxx and 6xxx groups which are common for example in the automotive industry. Aluminium has many unique physical properties. The properties which more than others have been shown to influence the welding process is its high reflection, high thermal conductivity, lo...

Developments in the US aluminium recycling industry

Energy Technology Data Exchange (ETDEWEB)

Bolling, R N

1983-06-01

In the USA scrap recovery of aluminium has gained in importance since the war. Today its amounts to about 32% of total supply. On the other hand primary production in the US seems to have hardly any expansion possibilities. The development of the aluminium beverage can is the clearest example for recycling growth. The increased use of aluminium in passenger cars has led to very close technical and local relations of aluminium foundries and secondary smelters. The changing nature of the aluminium business caused by the growth of recycling should be recognized and made use of.

Process for the manufacture of plates containing neutron poison from aluminium and aluminium alloys

International Nuclear Information System (INIS)

Bauer, G.; Pollmann, E.; Srostlik, P.

1985-01-01

A process for guaranteeing sub-critical arrangements of nuclear fuel in tranport and/or storage containers is described, in which a homogeneous distribution of neutron poison in the aluminium matrix is guaranteed. A homogeneous mixture of aluminium powder and neutron poison powder is produced, this is pressed into plates in several stages, dried and made into hollow aluminium profiles of rectangular cross-section. The open ends of the hollow profile are then closed and this is rolled to the required dimension at 470-500 0 C. (orig./HP) [de

Chapter 1. Economic aspects of aluminium production

International Nuclear Information System (INIS)

Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

2011-01-01

This article is devoted to economic aspects of aluminium production. Therefore, the perspectives of development of aluminium production, the base components of aluminium cost and economic security of enterprise are considered in this chapter.

Aluminium and nickel in human albumin solutions

DEFF Research Database (Denmark)

Gammelgaard, Bente; Sandberg, E

1989-01-01

Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

Aluminium beverage can recycling

Energy Technology Data Exchange (ETDEWEB)

Lewinski, A von

1985-08-01

Canned beverages have become a controversial issue in this era of ecological sensitivity. METALL has already discussed the problem of can recycling. The present article discusses the technical aspects of aluminium can recycling. Two further articles will follow on aluminium can recycling in North America and on the results of European pilot projects.

Removal of chromium (VI) from water by micro-alloyed aluminium ...

African Journals Online (AJOL)

This paper deals with Cr(VI) ion removal from water, by micro-alloyed aluminium composite (MAlC), under flow conditions. In a water environment the MAlC acts as a strong reducing agent. Dissolving it in water is accompanied by the generation of Al(III) ions and reduction of water to H2, with OH- ions. The final product is ...

Stainless steel fibre reinforced aluminium matrix composites processed by squeeze casting: relationship between processing conditions and interfacial microstructure

International Nuclear Information System (INIS)

Colin, C.; Marchal, Y.; Boland, F.; Delannay, F.

1993-01-01

This work investigates the influence of some processing parameters on the extent of interfacial reaction in squeeze cast aluminium matrix composites reinforced with 12 μm diameter, continuous stainless steel fibres. The average thickness of the reaction layer at fibre/matrix interfaces was measured by image analysis. When casting was made in a die at room temperature, the thickness of the reaction layer was affected on a distance of several mm from the lateral surface or from the bottom of the preform. The results indicate that the major part of the reaction occurs before solidification of the liquid metal. The control of the extent of interfacial reaction can be achieved through optimization of both infiltration parameters and features of the preform such as the volume fraction of the fibres. (orig.)

Effect of hydrogen on aluminium and aluminium alloys: A review

DEFF Research Database (Denmark)

Ambat, Rajan; Dwarakadasa, E.S.

1996-01-01

Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

Raw materials for aluminium production

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.

Electron beam welding of aluminium components

International Nuclear Information System (INIS)

Maajid, Ali; Vadali, S.K.; Maury, D.K.

2015-01-01

Aluminium is one of the most widely used materials in industries like transportation, shipbuilding, manufacturing, aerospace, nuclear, etc. The challenges in joining of aluminium are distortion, cleanliness and quality. Main difficulties faced during fusion welding of aluminium components are removal of surface oxide layer, weld porosity, high heat input requirement, distortion, hot cracking, etc. Physical properties of aluminium such as its high thermal conductivity, high coefficient of thermal expansion, no change in colour at high temperature, large difference in the melting points of the metal and its oxide (∼ 1400 °C) compound the difficulties faced during welding. Gas Tungsten Arc Welding (GTAW), Gas Metal Arc Welding (GMAW), Plasma Arc Welding (PAW), etc are generally used in industries for fusion welding of aluminium alloys. However in case of thicker jobs the above processes are not suitable due to requirements of elaborate edge preparation, preheating of jobs, fixturing to prevent distortion, etc. Moreover, precise control over the heat input during welding and weld bead penetration is not possible with above processes. Further, if heat sensitive parts are located near the weld joint then high energy density beam welding process like Electron Beam Welding (EBW) is the best possible choice for aluminium welding.This paper discusses EB welding of aluminium components, typical geometry of components, selection/optimization of welding parameters, problems faced during standardization of welding and process parameters and their remedies etc.

Potentiometric titration curves of aluminium salt solutions and its species conversion in the hydrolysis-polymerization course

Directory of Open Access Journals (Sweden)

Chenyi Wang

2008-12-01

Full Text Available A new concept of critical point is expounded by analysing the potentiometric titration curves of aluminium salt solutions under the moderate slow rate of base injection. The critical point is defined as the characteristic spot of the Al3+ salt solutions potentiometric titration curve, which is related to the experiment conditions. In addition, the changes of critical points reflect the influence of experiment conditions on the course of the hydrolysis-polymerization and the conversion of hydroxyl polynuclear aluminum species. According to the OH/Al mole ratio, the Al species can be divided into four regions quantitatively by three characteristic points on the titration curves: Part I, Al3+/Ala region, consist chiefly of Al3+ and mononuclear Al; Part II, the small/middle polynuclear Al region, including Al2-Al12; Part III, the large-size polynuclear aluminum region, consistent with predominantly Al13-Al54 and a little sol/gel Al(OH3; Part IV, the dissolving region of sol/gel Alc, only Al(OH 3 (aq or am and Al(OH4- species, which set up a base to study on the hydrolysis-polymerization of Al3+. At the same time, significant effects of total aluminum concentration, temperature, halide ion, silicate radical, and organic acid radical on the titration curves and its critical points were observed. Given the three critical points which demarcating the aluminum forms, we carry out a through investigation into the fundamental regulations of these factors’ influence, and offer a fresh train of thought to study the hydrolysis-polymerization of Al3+ in soil solutions.

A hybrid aluminium alloy and its zoo of interacting nano-precipitates

Energy Technology Data Exchange (ETDEWEB)

Wenner, Sigurd, E-mail: sigurd.wenner@ntnu.no [Department of Physics, NTNU, Høgskoleringen 5, NO-7491 Trondheim (Norway); Marioara, Calin Daniel; Andersen, Sigmund Jarle [Materials and Chemistry, SINTEF, Høgskoleringen 5, NO-7491 Trondheim (Norway); Ervik, Martin; Holmestad, Randi [Department of Physics, NTNU, Høgskoleringen 5, NO-7491 Trondheim (Norway)

2015-08-15

An alloy with aluminium as its base element is heat treated to form a multitude of precipitate phases known from different classes of industrial alloys: Al–Cu(–Mg), Al–Mg–Si–Cu, and Al–Zn–Mg. Nanometer-sized needle-shaped particles define the starting point of the phase nucleation, after which there is a split in the precipitation sequence into six phases of highly diverse compositions and morphologies. There are several unique effects of phases from different alloy systems being present in the same host lattice, of which we concentrate on two: the replacement of Ag by Zn on the Ω interface and the formation of combined plates of the θ′ and C phases. Using atomically resolved scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy, we investigate the formation mechanisms, crystal structures and compositions of the precipitates. - Graphical abstract: Display Omitted - Highlights: • An aluminium alloy composition in-between the 2/6/7xxx systems was investigated. • Six different phases from the three systems coexist in an over-aged state. • All phases with 〈001〉{sub Al} coherencies can nucleate on 6xxx needle precipitates. • Modified theta′ and omega interfaces are observed.

Corrosion of aluminium-clad spent fuel at RA research reactor

International Nuclear Information System (INIS)

Pesic, M.; Maksin, T.; Dobrijevic, R.; Idjakovic, Z.

2003-01-01

Almost 95% of all spent fuel elements of the RA research reactor in the Vinca Institute of Nuclear Sciences, Belgrade, Serbia and Montenegro, are stored in 30 aluminium barrels and about 300 stainless steel channel-holders in the temporary spent fuel storage water pool. The first activities of sludge and water samples, taken from the pool, were measured in 1996-1997 and were followed by analysis of chemical composition of samples. Visual inspections of fuel elements in some stainless steel tubes and of the fuel channels stored in the reactor core have shown that some deposits cover aluminium cladding. Stains and surface discoloration are noted on many of the spent fuel elements that were examined visually during the core unloading and inspections carried out in 1979 - 1984. Some of water samples, taken from pool, about a 150 stainless steel tubes and 16 barrels have shown very high 137-Cs activity compared to low activity measured in pool water. It was concluded that aluminium cladding of the fuel elements was penetrated due to corrosion process. Study on influence of water corrosion processes in the RA reactor storage pool was started within the framework of the IAEA CRP 'Corrosion of Research Reactor Aluminium-Clad Spent Fuel in Water' in 2002. The first test rack with various aluminium and stainless steel coupons, supplied by the IAEA, was immersed in the pool already in 1996. New racks were immersed in 2002 and 2003. The rack immersed in 1996 was taken out from the pool in 2002 and the rack immersed in 2002 was taken out in 2003. Results of the examination of these racks, carried out according to the strategy and the protocol, proposed by the IAEA, are described in this paper. (author)

Chapter 2. Theoretical aspects of aluminium production

International Nuclear Information System (INIS)

Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

2011-01-01

This article is devoted to theoretical aspects of aluminium production. Thus, the electrochemistry of electrolysis process, calculation of base industrial indicators of aluminium electrolytic cell, and processes occurring on anode and cathode were considered. Factors, which increase the current output and electrolytic cell productivity were studied. The side effects, including anode effect, sodium extraction on cathode, aluminium dissolution in the electrolyte, aluminium carbide formation, and influence of admixtures in the electrolyte were studied as well.

Anodization of cast aluminium alloys produced by different casting methods

Directory of Open Access Journals (Sweden)

K. Labisz

2008-08-01

Full Text Available In this paper the usability of two casting methods, of sand and high pressure cast for the anodization of AlSi12 and AlSi9Cu3 aluminium cast alloys was investigated. With defined anodization parameters like electrolyte composition and temperature, current type and value a anodic alumina surface layer was produced. The quality, size and properties of the anodic layer was investigated after the anodization of the chosen aluminium cast alloys. The Alumina layer was observed used light microscope, also the mechanical properties were measured as well the abrasive wear test was made with using ABR-8251 equipment. The researches included analyze of the influence of chemical composition, geometry and roughness of anodic layer obtained on aluminum casts. Conducted investigations shows the areas of later researches, especially in the direction of the possible, next optimization anodization process of aluminum casting alloys, for example in the range of raising resistance on corrosion to achieve a suitable anodic surface layer on elements for increasing applications in the aggressive environment for example as materials on working building constructions, elements in electronics and construction parts in air and automotive industry.

Aluminium in brain tissue in familial Alzheimer's disease.

Science.gov (United States)

Mirza, Ambreen; King, Andrew; Troakes, Claire; Exley, Christopher

2017-03-01

The genetic predispositions which describe a diagnosis of familial Alzheimer's disease can be considered as cornerstones of the amyloid cascade hypothesis. Essentially they place the expression and metabolism of the amyloid precursor protein as the main tenet of disease aetiology. However, we do not know the cause of Alzheimer's disease and environmental factors may yet be shown to contribute towards its onset and progression. One such environmental factor is human exposure to aluminium and aluminium has been shown to be present in brain tissue in sporadic Alzheimer's disease. We have made the first ever measurements of aluminium in brain tissue from 12 donors diagnosed with familial Alzheimer's disease. The concentrations of aluminium were extremely high, for example, there were values in excess of 10μg/g tissue dry wt. in 5 of the 12 individuals. Overall, the concentrations were higher than all previous measurements of brain aluminium except cases of known aluminium-induced encephalopathy. We have supported our quantitative analyses using a novel method of aluminium-selective fluorescence microscopy to visualise aluminium in all lobes of every brain investigated. The unique quantitative data and the stunning images of aluminium in familial Alzheimer's disease brain tissue raise the spectre of aluminium's role in this devastating disease. Copyright © 2016 The Authors. Published by Elsevier GmbH.. All rights reserved.

Detection and characterisation of aluminium-containing nanoparticles in Chinese noodles by single particle ICP-MS.

Science.gov (United States)

Loeschner, Katrin; Correia, Manuel; López Chaves, Carlos; Rokkjær, Inge; Sloth, Jens J

2018-01-01

This study investigated Chinese noodles for the presence of aluminium-containing nanoparticles by using inductively coupled plasma mass spectrometry in single particle mode (spICP-MS) after enzymatic digestion by α-amylase. The aluminium concentrations in the noodle samples, determined by conventional ICP-MS without or with the use of hydrofluoric acid for digestion, were 5.4 ± 1.9 µg/g and 10.1 ± 2.2 µg/g (N = 21), respectively. Aluminium-containing nanoparticles were detected by spICP-MS in all 21 samples. Depending on the assumed particle composition, Al 2 O 3 or Al 2 O 3 ∙2SiO 2 ∙2H 2 O, the median particle diameters were either below or above 100 nm, respectively. The minimum detectable particle diameter by spICP-MS was between 54 and 83 nm. The mass recovery of aluminium in the form of particles was between 5% and 18%. The presented work reports for the first time the detection of Al-containing particles in food by spICP-MS.

Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

Science.gov (United States)

Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

2016-02-01

Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

Phytoplankton species composition of four ecological provinces in Yellow Sea, China

Science.gov (United States)

Li, Xiaoqian; Feng, Yuanyuan; Leng, Xiaoyun; Liu, Haijiao; Sun, Jun

2017-12-01

The ecological province based on phytoplankton species composition is important to understanding the interplay between environmental parameters and phytoplankton species composition. The aim of this study was to establish phytoplankton species composition ecological pattern thus elucidate the relationship between environmental factors and the phytoplankton species composition in the ecological provinces. Phytoplankton samples were collected from 31 stations in Yellow Sea (121.00°-125.00°E, 32.00°-39.22°N) in November 2014. The samples were enumerated and identified with the Utermöhl method under an optical inverted microscope-AE2000 with magnifications of 200 × or 400 ×. In the present study, a total of 141 taxa belonging to 60 genera of 4 phyla of phytoplankton were identified, among them 101 species of 45 genera were Bacillariophyta, 36 species of 11 genera were Dinophyta, 3 species of 3 genera were Chrysophyta and 1 species of 1 genera was Chlorophyta. The study area was divided into 4 ecological provinces according to an unsupervised cluster algorithm applied to the phytoplankton biomass. A T-S (Temperature-Salinity) scatter diagram depicted with data of water temperature and salinity defined by environmental provinces matched well with the ecological provinces. The results of Canonical Correspondence Analysis (CCA) indicated that the phytoplankton species composition was mainly correlated with temperature, salinity and silicate concentration in the studied area. A method of establishing ecological provinces is useful to further understanding the environmental effects on the marine phytoplankton species composition and the consequent marine biogeochemistry.

Research and development of advanced aluminium/graphite composites for thermal management applications

OpenAIRE

Wyszkowska, Edyta; Olejnik, Ewa; Bertarelli, Alessandro

2015-01-01

Thermal management materials are continuously gaining importance as a consequence of everlasting evolution in performance of electronic and electric devices. In particular, by improving the heat exchanger’s materials' properties (i.e. thermal conductivity) it is possible to boost further performance and miniaturization of such devices. Due to their high thermal conductivity, Copper and Aluminium are currently the most commonly used materials for thermal management applications. However, the m...

Silane pre-treatments on copper and aluminium

International Nuclear Information System (INIS)

Deflorian, F.; Rossi, S.; Fedrizzi, L.

2006-01-01

A large part of aluminium products are coated with an organic layer in order to improve the corrosion resistance. Copper surfaces are also sometimes protected with an organic coating to improve the durability or the aesthetic properties. Examples of industrial applications are household appliances and heat exchanger components. For these applications it is not rare to have the industrial need to treat at the same time components made of aluminium and copper. In order to extend the service life of the organic coated copper a specific surface pre-treatment is often required. Nevertheless, probably because of the limited market of this application, no specific pre-treatments for copper are industrially developed, with the exception of cleaning procedures, but simply extensions of existing pre-treatments optimised for other metals (aluminium, zinc) are used. The application of silane pre-treatments as adhesion promoters for organic coated metals is remarkably increasing in the last decade, because silanes offer very good performance together with high environmental compatibility. The idea is therefore to try to develop a specific silane based pre-treatment for copper. The starting point is the existing silane products for aluminium, optimising the composition and the application conditions (concentration, temperature, pH of the bath, etc.) in order to develop a high performance copper alloy pre-treatment increasing the protective properties and the adhesion of a successively applied organic coating. Moreover these pre-treatments could be used for aluminium alloys too and therefore could be suggested for multi-metals components. The deposits were analysed using FTIR spectroscopy and optical and electron microscopic observations. A careful electrochemical characterisation, mainly by electrochemical impedance spectroscopy measurements (EIS) was carried out to highlight the presence of silane and to evaluate the performance of the different deposits. In order to study an

Challenges in LCA modelling of multiple loops for aluminium cans

DEFF Research Database (Denmark)

Niero, Monia; Olsen, Stig Irving

considered the case of closed-loop recycling for aluminium cans, where body and lid are different alloys, and discussed the abovementioned challenge. The Life Cycle Inventory (LCI) modelling of aluminium processes is traditionally based on a pure aluminium flow, therefore neglecting the presence of alloying...... elements. We included the effect of alloying elements on the LCA modelling of aluminium can recycling. First, we performed a mass balance of the main alloying elements (Mn, Fe, Si, Cu) in aluminium can recycling at increasing levels of recycling rate. The analysis distinguished between different aluminium...... packaging scrap sources (i.e. used beverage can and mixed aluminium packaging) to understand the limiting factors for multiple loop aluminium can recycling. Secondly, we performed a comparative LCA of aluminium can production and recycling in multiple loops considering the two aluminium packaging scrap...

Durability of bare and anodised aluminium in atmosphere of very different corrosivities I. Bare aluminium

International Nuclear Information System (INIS)

Gonzalez, J. A.; Escudero, E.; Lopez, V.; Simancas, J.; Morcillo, M.

2004-01-01

The behaviour of bare aluminium is studied in atmospheric exposure at 11 natural testing stations with salinity levels ranging between 2.1 and 684 mg Cl''- m''-2 d''-1. In atmospheres of low or moderate aggressivity aluminium behaves as a passive material, though the insignificant corrosion that is produced is sufficient to spoil its appearance. In contrast, at salinity levels of 50 mg Cl''- m''-2 ''-1 or above, aluminium is susceptible to pitting corrosion even in the first year of atmospheric exposure, or in the second year at salinities of ≤ 10 mg Cl''- m''-2 d''-1. For comparative purposes, results are included for aluminium protected with an anodic film of 28 μm thickness exposed at the same testing stations. A 28 μm anodic film, correctly sealed, prevents the risk of localised corrosion even in the most unfavourable situations. (Author) 23 refs

Fatigue test on aluminium bridges

NARCIS (Netherlands)

Maljaars, J.; Soetens, F.; Straalen, van IJ.J.

2005-01-01

Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge

Fatal aluminium phosphide poisoning

Directory of Open Access Journals (Sweden)

Meena Mahesh Chand

2015-06-01

Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

Pemanfaatan serat silicon carbon dan partikel alumina pada matrik aluminium untuk meningkatkan sifat mekanis material komposit

Directory of Open Access Journals (Sweden)

Ketut Suarsana

2017-03-01

Full Text Available Abstrak: Pemanfaatan penguat material komposit berbasis serat dan juga partikel pada pembuatan bahan komposit sekarang ini sangatpotensial untuk dikembangkan dan diteliti. Beragam sumber serat dan juga penguat dalam bentuk partikel bisa didapat dari seratalami dari tumbuh-tubuhan dan juga serat yang sudah dikenakan perlakuan sebelumnya. Indonesia memiliki potensi sumberalam yang sangat potensial terutama sebgai sumber serat dari tumbuhan juga berupa logam aluminium (bauxite dari fosil.Bahan ini dapat dimanfaatkan untuk kebutuhan masyarakat industri sebagai bahan dasar pembuatan komposit bermatrikAluminium dan sebagai penguat berupa serat maupun partikel alumina. Metode pembuatan Aluminum Matrix Composite (AMCdengan proses metalurgi serbuk pada gaya tekan/kompaksi 2,5 ton mengunakan alat press hydrolik, waktu penahanan 15menit, serta proses perlakuan pada variasi komposisi berat (%wt. Variasi komposisi penguat serat Silicon Carbon (SiC danAl2O3 (alumina pada matrik Aluminium adalah : 30% SiC + 0% Al203, 27% SiC + 3% Al203, 24% SiC + 6% Al203 dan 21% SiC+ 9% Al203 dengan matrik 70% Al, pada kondisi tempertaur 500oC, 550oC dan 600oC. Setelah material komposit terbentuk, diujiuntuk mengetahui sifat mekanik akibat pengaruh variasi komposisi antara matrik dan penguatan pada komposit. Uji karakteristikdilakukan di laboratorium untuk menggetahui sifat kekuatan dan kekerasan material komposit. Selanjutnya dicari hubunganantara sifat masing-masing komposisi penguat serat SiC dan Al2O3 pembentuk komposit yang dibuat untuk mengetahui manfaatdari penguat serat dan partikel alumina.Kata Kunci: Sifat kekuatan, kekerasan, serat SiC dan Al2O3 Abstract: Utilization reinforcement fiber-based composite material and particles in the manufacture of composite materials now havepotential to be developed and researched. Various sources of fiber and reinforcement in particle form can be obtained fromnatural fibers from plants and fiber that has been subjected to a

Friction Welding of Aluminium and Aluminium Alloys with Steel

Directory of Open Access Journals (Sweden)

Andrzej Ambroziak

2014-01-01

Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

Aluminium cables in automotive applications : Prestudy of aluminium cable uses in Scania products&Failure analysis and evaluation

OpenAIRE

Man, Yu

2016-01-01

The increasing demand of light constructed vehicles as well as soaring price of copper metal owing to limited nature resources have been promoting the use of aluminium metal as an alternative conductor of automotive cables. This thesis work is to lay theoretical foundations for further research and development regarding the introduction of new automotive cables i.e. aluminium cables. Current application of automotive aluminium cables in automotive industry as well as failure analysis and eval...

Application of radioactivation analysis for determination of impurities in aluminium, raw materials and in samples from aluminium production process

International Nuclear Information System (INIS)

Vucina, L.J.

1977-01-01

Trace elements in aluminium, raw materials and in the samples from different stages of aluminium production were determined by nondestructive neutron radioactivation analysis. The samples were taken from the Bayer's process of alumina production (bauxite, red sludge and alumina), from the components of the reduction cell (anode, criolyte and AlF 3 ) and of the final product - aluminium (purity 99.5-99.7%). Under given set of conditions ten trace elements (V,La,Ga,Mn,Co,Cr,Sc,Sb,Zn and Fe) were determined in aluminium and followed through the production process. It was found that the main impurities in aluminium are iron (0.15%) and zinc (0.O6%). It has been concluded that the purity of produced aluminium depends mainly on the purity of used alumina. The second important source of contamination of aluminium is anode. The results obtained by radioactivation analysis for V, Mn, Cr and Fe fall within the ranges of concentrations of these elements determined by use of other methods (volumetry, spectrophotometry, atomic absorption). Higher values for zinc were obtained by radioactivation analysis, probably due to unsatisfactory irradiation and measuring conditions for this element. The possibilities of application of radioactivation analysis to these kinds of samples are also disscused

Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

Science.gov (United States)

Kramer, Matthias F; Heath, Matthew D

2014-07-16

We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

Spark counting technique with an aluminium oxide film

International Nuclear Information System (INIS)

Kawai, H.; Koga, T.; Morishima, H.; Niwa, T.; Nishiwaki, Y.

1980-01-01

Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm 2 . The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

Steam generated conversion coating on aluminium alloys

DEFF Research Database (Denmark)

Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed...... into functional conversion coatings in order to enhance corrosion resistance and adhesion to paint systems. Chromium based conversion coatings have been extensively used on aluminium alloys to improve adhesion of subsequent paint layers and corrosion resistance. However, the use of hexavalent chromium is strictly...... regulated due to its toxic nature and suspected carcinogenicity. So, it is highly imperative to develop other alternatives for chrome conversion coatings. Treatment of aluminium with natural water at elevated temperatures results in the formation of different forms of aluminium oxide (γ-AlO(OH) , Al(OH)3...

Advances in development and application of aluminium batteries

DEFF Research Database (Denmark)

Qingfeng, Li; Zhuxian, Qiu

2001-01-01

Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation o...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

Alveolar proteinosis associated with aluminium dust inhalation.

Science.gov (United States)

Chew, R; Nigam, S; Sivakumaran, P

2016-08-01

Secondary alveolar proteinosis is a rare lung disease which may be triggered by a variety of inhaled particles. The diagnosis is made by detection of anti-granulocyte-macrophage colony-stimulating factor antibodies in bronchoalveolar lavage fluid, which appears milky white and contains lamellar bodies. Aluminium has been suggested as a possible cause, but there is little evidence in the literature to support this assertion. We report the case of a 46-year-old former boilermaker and boat builder who developed secondary alveolar proteinosis following sustained heavy aluminium exposure. The presence of aluminium was confirmed both by histological examination and metallurgical analysis of a mediastinal lymph node. Despite cessation of exposure to aluminium and treatment with whole-lung lavage which normally results in improvements in both symptoms and lung function, the outcome was poor and novel therapies are now being used for this patient. It may be that the natural history in aluminium-related alveolar proteinosis is different, with the metal playing a mediating role in the disease process. Our case further supports the link between aluminium and secondary alveolar proteinosis and highlights the need for measures to prevent excessive aluminium inhalation in relevant industries. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

AMINOACID COMPOSITION OF SOME SPECIES FROM INULA GENUS

Directory of Open Access Journals (Sweden)

A. A. Kruglaya

2016-01-01

Full Text Available The majority of medicinal plants and medicinal plant raw materials are understudied pharmacgostically. These plants include species from Inula genus, which range in Russia amounts to up to 40 species. Rhizomes and roots of the Inula helenium L. are broadly applied in scientific and traditional medicine. They have expectorate, styptic, and anti-inflammatory properties.The purpose of the study was to determine the amino-acid composition of some species from Inula genus (Inula germanica, Inula ensifolia, Inula aspera, Inula orientalis, which grow in different regions if the North Caucasus.Methods. The studies were carried out using AAA 400 amino acid analyzer, highly specialized automatized liquid chromatographer with computer management. Aboveground parts of the plants, gathered in mass blossom phase from wild-growing plants and then dried out were the objects of the study.Results. For the first time the amino acid composition and raw protein of some species from Inula genus was determined (Inula germanica, Inula ensifolia, Inula aspera, Inula orientalis, 16 amino acids were discovered, 7 of which were essential, and raw proteins which substantival composition amounted to 16.19% in Inula germanica, 10.78% in Inula ensifolia, Inula aspera (11.15%, Inula orientalis (13.94%.Conclusion. The results of the studies conducted broaden the data about amino acids and protein composition and quantitative content in the species from Inula genus and can be used to develop methods of analysis of the drugs, obtained from these plants.

An inductively coupled plasma atomic emission spectrometric (ICP-AES) determination of boron and other trace impurities in aluminium metal

International Nuclear Information System (INIS)

Deshpande, S.S.; Patil, P.B.; Karanjikar, N.P.

2002-01-01

The optimisation and use of ICP-AES technique for the analysis of aluminium metal for B, Cr, Cu, Fe, Mg, Mn, Ni, Si, Ti, V and Zn in the concentration range 5.0 to 50.0 ppm is described. The method involves the dissolution of aluminium metal in acqua-regia. The matrix aluminium solution (2mg/ml) is mixed with composite impurity solution in proper proportions, for getting the required set of standards. JY 1 metre Czerny-Turner Scanning monochromator is used to measure peak intensities corresponding to each analyte wavelength selected. The mean relative standard deviation (RSD) of the method for various elements is found to be 4.0% -2.0% in the concentration range studied. (author)

Composition of microfouling on aluminium and fibre glass panels exposed in Agatti waters (Lakshadweep Island)

Digital Repository Service at National Institute of Oceanography (India)

Raveendran, T.V.; Sankaran, P.D.; Wagh, A.B.

Rate of microfouling build-up was high during the initial periods of exposure of test surfaces but decreased with the increasing duration. Fibre glass surfaces showed higher deposition than those of aluminium. Carbohydrates and lipids were the major...

Effect of Lubrication on Sliding Wear of Red Mud Particulate Reinforced Aluminium Alloy 6061

OpenAIRE

N. Panwar; R.P. Poonia; G. Singh; R. Dabral; A. Chauhan

2017-01-01

In present study, Red mud, an industrial waste, has been utilized as a reinforcement material to fabricate Aluminium 6061 matrix based metal matrix composite. Taguchi L18 orthogonal array has been employed for fabrication of composite castings and for conducting the tribological experimentation. ANOVA analysis has been applied to examine the effect of individual parameters such as sliding condition: dry and wet, reinforcement weight fraction, load, speed, and sliding distance on specific wear...

Ion beam analysis of aluminium in thin layers

International Nuclear Information System (INIS)

Healy, M.J.F.; Pidduck, A.J.; Dollinger, G.; Gorgens, L.; Bergmaier, A.

2002-01-01

This work quantifies aluminium in thin surface and near surface layers. In one example, the layer overlies a thin gallium nitride layer on an aluminium oxide substrate and in a second example the aluminium exists just below the surface of an indium arsenide substrate. The technique of non-Rutherford elastic backscattering of protons was used for the samples where aluminum in the layer of interest needed to be resolved from aluminium in the sapphire substrate and the results were corroborated at the Technische Universitaet Muenchen using heavy ion elastic recoil detection analysis. In the second example, where it was unnecessary to isolate the signal of aluminium in the layer of interest (as the substrate contained no aluminium), then the 27 Al(d,p 01 ) 28 Al nuclear reaction was used. The elastic proton scattering cross section of aluminum was found to vary very rapidly over the energy range of interest

Atmospheric pressure plasma-assisted femtosecond laser engraving of aluminium

Science.gov (United States)

Gerhard, Christoph; Gimpel, Thomas; Tasche, Daniel; Koch née Hoffmeister, Jennifer; Brückner, Stephan; Flachenecker, Günter; Wieneke, Stephan; Schade, Wolfgang; Viöl, Wolfgang

2018-05-01

In this contribution, we report on the impact of direct dielectric barrier discharge argon plasma at atmospheric pressure on femtosecond laser engraving of aluminium. It is shown that the assisting plasma strongly affects the surface geometry and formation of spikes of both laser-engraved single lines and patterns of adjacent lines with an appropriate overlap. Further, it was observed that the overall ablation depth is significantly increased in case of large-scale patterning whereas no notable differences in ablation depth are found for single lines. Several possible mechanisms and underlying effects of this behaviour are suggested. The increase in ablation depth is supposed to be due to a plasma-induced removal of debris particles from the cutting point via charging and oxidation as supported by EDX analysis of the re-solidified debris. Furthermore, the impact of a higher degree of surface wrinkling as well as direct interactions of plasma species with the aluminium surface on the ablation process are discussed.

Dynamics of anopheline vector species composition and reported ...

African Journals Online (AJOL)

Indoor resting mosquitoes were collected between November 2013 and May 2014 using Pyrethrum spray collection (PSC). The mosquitoes were identified using morphological keys and species specific polymerase chain reaction (PCR) assays. The species composition of members of the An. gambiae complex and ...

The aluminium content of infant formulas remains too high.

Science.gov (United States)

Chuchu, Nancy; Patel, Bhavini; Sebastian, Blaise; Exley, Christopher

2013-10-08

Recent research published in this journal highlighted the issue of the high content of aluminium in infant formulas. The expectation was that the findings would serve as a catalyst for manufacturers to address a significant problem of these, often necessary, components of infant nutrition. It is critically important that parents and other users have confidence in the safety of infant formulas and that they have reliable information to use in choosing a product with a lower content of aluminium. Herein, we have significantly extended the scope of the previous research and the aluminium content of 30 of the most widely available and often used infant formulas has been measured. Both ready-to-drink milks and milk powders were subjected to microwave digestion in the presence of 15.8 M HNO3 and 30% w/v H2O2 and the aluminium content of the digests was measured by TH GFAAS. Both ready-to-drink milks and milk powders were contaminated with aluminium. The concentration of aluminium across all milk products ranged from ca 100 to 430 μg/L. The concentration of aluminium in two soya-based milk products was 656 and 756 μg/L. The intake of aluminium from non-soya-based infant formulas varied from ca 100 to 300 μg per day. For soya-based milks it could be as high as 700 μg per day. All 30 infant formulas were contaminated with aluminium. There was no clear evidence that subsequent to the problem of aluminium being highlighted in a previous publication in this journal that contamination had been addressed and reduced. It is the opinion of the authors that regulatory and other non-voluntary methods are now required to reduce the aluminium content of infant formulas and thereby protect infants from chronic exposure to dietary aluminium.

Preparation of aluminium lakes by electrocoagulation

OpenAIRE

Prapai Pradabkham

2008-01-01

Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

Considerations on the biochemical composition of some freshwater zooplankton species.

Directory of Open Access Journals (Sweden)

Nicoletta RICCARDI

1999-02-01

Full Text Available The mean elemental (C, H, N and biochemical composition (lipids, carbohydrates and proteins of some abundant crustacean zooplankton species of Italian insubric lakes has been estimated by the analysis of samples collected at different seasons from various environments (Lake Maggiore, Lake Varese, Lake Comabbio, Lake Monate. From each sample an adequate number of specimens of each abundant species was sorted and analyzed by a CHN elemental analyzer. The percentage of lipids, carbohydrates and proteins and the calorific content were calculated from the elemental composition according to Gnaiger & Bitterlich (1984. Inter- and intraspecific variability of biochemical composition was quite high, while elemental composition and calorific content were less variable. An estimate of the mean elemental and biochemical composition of each species was obtained by pooling the data. These mean values have been used to estimate the pools of elements and compounds in the crustacean zooplankton of Lake Comabbio to provide an example of the importance of a multiple approach in zooplankton studies.

Wear behaviour of coating of aluminium matrix composites fabricated by thermal spray method; Comportamiento a desgaste de recubrimientos de material compuesto de matriz de aluminio fabricados por proyeccion termica

Energy Technology Data Exchange (ETDEWEB)

Campo, M.; Escalera, M. D.; Torres, B.; Rams, J.; Urena, A.

2007-07-01

In this work, the wear behaviour of coatings made of aluminium matrix composites reinforced with 20% of SiC particles and manufactured by thermal spray method with oxyacetylene flame has been investigated. the wear behaviour between coating with uncoated particles and sol-gel silica coated ones heat treated at 500 degree centigree and 725 degree centigree have been compared. The sprayed coatings with silica coated particles are more homogeneous and less porous due to increase of wettability by molten aluminium that takes place on coated particles. The microstructure of the sprayed coatings, the wear surfaces and the wear debris have been analysed using optical microscopy, scanning electron microscopy and micro-analysis techniques (EDX). The results show a smaller wear rate, a lower friction coefficient and more reduced loss of mass for the coatings sprayed with particles with sol-gel silica coatings than those made with uncoated particles. (Author) 15 refs.

Serum aluminium levels of workers in the bauxite mines.

Science.gov (United States)

de Kom, J F; Dissels, H M; van der Voet, G B; de Wolff, F A

1997-01-01

Aluminium is produced from the mineral bauxite. Occupational exposure is reported during the industrial processing of aluminium and is associated with pulmonary and neurotoxicity. However, data on exposure and toxicity of workers in the open bauxite mining industry do not exist. Therefore, a study was performed to explore aluminium exposure in employees involved in this bauxite mining process in a Surinam mine. A group of workers occupationally exposed to aluminium in an open bauxite mine were compared with a group of nonexposed wood processors. Serum aluminium was analyzed using atomic absorption spectrometry Data from the clinical chemistry of the blood and a questionnaire were used to explore determinants for aluminium exposure. No significant difference between serum aluminium in the exposed (4.4 +/- 2.0 micrograms/L, n = 27) and control group (5.1 +/- 1.5 micrograms/L, n = 27) was detected. For the serum concentration of the clinical chemical variables (calcium, citrate, and creatinine), a statistically significant difference was computed (p < or = 0.02) between the exposed and control group. All levels were slightly higher in the exposed group; no statistically significant correlations with serum aluminium were found. In this study, serum aluminium values were in the normal range, no significant difference between the groups could be detected despite long-term occupational exposure.

Argon-arc welding of heat resisting aluminium alloys

International Nuclear Information System (INIS)

Ryazantsev, V.I.; Fedoseev, V.A.

1997-01-01

Welding of aluminium heat resisting alloys of the Al-Cu-Mg system is studied. The hot-shortness of heat-resistant alloys M40, 1150 and 1151 are at the level of aluminium alloys 1201 and by 2-3 times lower as compared to the aluminium alloy AMg6. The M40, 1150 and 1151 alloys have unquestionable advantages against other know aluminium alloys only at temperatures of welded structures operation, beginning with 150-2000 deg C and especially at 250 deg C

Net shape powder processing of aluminium

International Nuclear Information System (INIS)

Schaffer, G.B.

2000-01-01

The increasing interest in light weight materials coupled to the need for cost-effective processing have combined to create a significant opportunity for aluminium powder metallurgy. Net shape processing of aluminium using the classical press-and-sinter powder metallurgy technique is a unique and important metal-forming method which is cost effective in producing complex parts at, or very close to, final dimensions. This paper provides an overview of the net shape powder processing of aluminium. Current research is critically reviewed and the future potential is briefly considered

Wear behaviour of A356 aluminium alloy reinforced with micron and nano size SiC particles

CSIR Research Space (South Africa)

Camagu, ST

2013-07-01

Full Text Available A method for producing metal matrix composites MMC was successfully implemented for mixing nano and low micron (“Hybrid”) sized SiC reinforcing particles in an aluminium alloy matrix. Due to the improved specific modulus and strength, MMC...

Method for aluminium dross utilization

International Nuclear Information System (INIS)

Lucheva, B.; Petkov, R.; Tzonev, Tz.

2003-01-01

A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

Preparation of aluminium lakes by electrocoagulation

Directory of Open Access Journals (Sweden)

Prapai Pradabkham

2008-07-01

Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

Finite Element Simulation of Aluminium/GFRP Fibre Metal Laminate under Tensile Loading

Science.gov (United States)

Merzuki, M. N. M.; Rejab, M. R. M.; Romli, N. K.; Bachtiar, D.; Siregar, J.; Rani, M. F.; Salleh, Salwani Mohd

2018-03-01

The response of a fibre metal laminate (FML) model to the tensile loading is predicted through a computational approach. The FML consisted with layers of aluminum alloy and embedded with one layer of composite material, Glass fibre Reinforced Plastic (GFRP). The glass fibre and aluminium alloy 2024-0 was laminated by using thermoset epoxy. A compression moulding technique was used in the process of a FML fabrication. The aluminium has been roughen by a metal sanding method which to improve the bonding between the fibre and metal layer. The main objective of this paper is to determine the failure behaviour of the FML under the tensile loading. The responses on the FML under the tensile loading were numerically performed. The FML was modelled and analysed by using Abaqus/CAE 6.13 version. Based on the experimental and FE data of the tensile, the ultimate tensile stress is 120 MPa where delamination and fibre breakage happened. A numerical model was developed and agreed well with the experimental results. The laminate has an inelastic respond to increase the tensile loads which due to the plasticity of the aluminium layers.

Investigation of aluminium state in some popular food, which are cooked in aluminium vessels, using spectroscopic analysis methods

International Nuclear Information System (INIS)

Al-Shahneh, M.; Saheune, Kh.

2009-01-01

Aluminium and lead elements were determined in drinking water and salt solution from chick-pea and faba-bean cooked in aluminium vessels and others from teflon for comparison using atomic absorption spectroscopy by graphite furnace. The relationship between heating time and aluminium quantities transferred to these food solutions was investigated. The lead element was determined taking into consideration the fact that this element may enter in these vessels somehow during the manufacturing process. Results show that the highest value of aluminium quantities was recorded in salt solution ( 17.022 μg/ml) without heating , followed by chick-pea solution (9.95 μg/ml), then faba-bean solution (2.81 μg/ml) when the heated period was 120 minutes. (author)

Effect of tempering on corrosion resistance of cast aluminium bronzes

International Nuclear Information System (INIS)

Aaltonen, P.; Klemetti, K.; Haenninen, H.

1985-01-01

The subject of this study is corrosion resistance of aluminium bronzes, which are copper base alloys containing aluminium up to 12% with additions of nickel, iron and manganese. The main conclutions that can be drawn are: (1) The dealloying corrosion resistance of nickel-aluminium bronze is much better than that of aluminium bronze with iron and manganese additions, but it is not immune; (2) The dealloying corrosion resistance of aluminium bronzes can be improved by appropiate heat treatments. The best properties were obtained by temperering between 600 and 800 deg C, depending on the initial microstructure; (3) In crevice conditions, where local acidification can occur, dealloying of aluminium bronzes is a consequence of the preferential attack of aluminium-rich phases. By appropriate tempering, a uniform distribution of aluminium-rich phases is obtained and the continous path for selective corrosion is not formed

What is the risk of aluminium as a neurotoxin?

Science.gov (United States)

Exley, Christopher

2014-06-01

Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

Determination of lattice orientation in aluminium alloy grains by low energy gallium ion-channelling

Energy Technology Data Exchange (ETDEWEB)

Silk, Jonathan R. [Aerospace Metal Composites Ltd., RAE Road, Farnborough, GU14 6XE (United Kingdom); Dashwood, Richard J. [WMG, University of Warwick, Coventry, CV4 7AL (United Kingdom); Chater, Richard J., E-mail: r.chater@imperial.ac.u [Department of Materials, Imperial College, London SW7 2AZ (United Kingdom)

2010-06-15

Polished sections of a fine-grained aluminium, silicon carbide metal matrix composite (MMC) alloy were prepared by sputtering using a low energy gallium ion source and column (FIB). The MMC had been processed by high temperature extrusion. Images of the polished surface were recorded using the ion-induced secondary electron emission. The metal matrix grains were distinguished by gallium ion-channelling contrast from the silicon carbide component. The variation of the contrast from the aluminium grains with tilt angle can be recorded and used to determine lattice orientation with the contrast from the silicon carbide (SiC) component as a reference. This method is rapid and suits site-specific investigations where classical methods of sample preparation fail.

Spectroscopic diagnostics of plasma during laser processing of aluminium

International Nuclear Information System (INIS)

Lober, R; Mazumder, J

2007-01-01

The role of the plasma in laser-metal interaction is of considerable interest due to its influence in the energy transfer mechanism in industrial laser materials processing. A 10 kW CO 2 laser was used to study its interaction with aluminium under an argon environment. The objective was to determine the absorption and refraction of the laser beam through the plasma during the processing of aluminium. Laser processing of aluminium is becoming an important topic for many industries, including the automobile industry. The spectroscopic relative line to continuum method was used to determine the electron temperature distribution within the plasma by investigating the 4158 A Ar I line emission and the continuum adjacent to it. The plasmas are induced in 1.0 atm pure Ar environment over a translating Al target, using f/7 and 10 kW CO 2 laser. Spectroscopic data indicated that the plasma composition and behaviour were Ar-dominated. Experimental results indicated the plasma core temperature to be 14 000-15 300 K over the incident range of laser powers investigated from 5 to 7 kW. It was found that 7.5-29% of the incident laser power was absorbed by the plasma. Cross-section analysis of the melt pools from the Al samples revealed the absence of any key-hole formation and confirmed that the energy transfer mechanism in the targets was conduction dominated for the reported range of experimental data

Spectroscopic diagnostics of plasma during laser processing of aluminium

Science.gov (United States)

Lober, R.; Mazumder, J.

2007-10-01

The role of the plasma in laser-metal interaction is of considerable interest due to its influence in the energy transfer mechanism in industrial laser materials processing. A 10 kW CO2 laser was used to study its interaction with aluminium under an argon environment. The objective was to determine the absorption and refraction of the laser beam through the plasma during the processing of aluminium. Laser processing of aluminium is becoming an important topic for many industries, including the automobile industry. The spectroscopic relative line to continuum method was used to determine the electron temperature distribution within the plasma by investigating the 4158 Å Ar I line emission and the continuum adjacent to it. The plasmas are induced in 1.0 atm pure Ar environment over a translating Al target, using f/7 and 10 kW CO2 laser. Spectroscopic data indicated that the plasma composition and behaviour were Ar-dominated. Experimental results indicated the plasma core temperature to be 14 000-15 300 K over the incident range of laser powers investigated from 5 to 7 kW. It was found that 7.5-29% of the incident laser power was absorbed by the plasma. Cross-section analysis of the melt pools from the Al samples revealed the absence of any key-hole formation and confirmed that the energy transfer mechanism in the targets was conduction dominated for the reported range of experimental data.

Solidification microstructures of aluminium-uranium alloys

International Nuclear Information System (INIS)

Ambrozio Filho, F.; Vieira, R.R.

1976-01-01

The solidification of microstrutures of aluminium-uranium alloys in the range of 4 to 20% uranium is investigated. The solidification was obtained both in ingot molds and under controlled directional solidification. The conditions for the presence of primary crystals and eutectic are discussed and an analysis of the influence of variables (growth rate and thermal gradient in the liquid) on the alloy structure is made. The effect of cooling rate on the alloy structures has been determined. It is found that the resulting structure can be derived from the kinectics concept, as required by the coupled-zone theory. Suggestions on the qualitative intervals of composition and temperatures with eutectic growth are presented [pt

Consolidation of copper and aluminium powders by spark plasma sintering

Science.gov (United States)

Saiprasad, M.; Atchayakumar, R.; Thiruppathi, K.; Raghuraman, S.

2016-09-01

Processing in the powder metallurgy route has emerged as an economical process for the production of near net shaped components with a wide range of desired mechanical properties suitable for various applications of industrial needs. This research work was conducted with an objective of studying the improvisation of density and hardness of Copper-Aluminium alloy prepared by spark plasma sintering. Cu-Al alloy with a composition of 95% copper and 5% aluminium was prepared by SPS process. SPS is a low voltage, DC pulse current activated, pressure-assisted sintering, which enables sintering at lower temperatures and shorter durations. The combination offered by Cu-Al alloy of high strength and high corrosion resistance results their applications under a wide variety of conditions. The density and hardness of the prepared sample were measured by conducting appropriate tests. Apparently, the values of hardness and density of the specimen prepared by SPS seemed to be better than that of conventional sintering. The experimental procedure, testing methodologies and analysis are presented.

Detection of aluminium in different culinary media using black ...

African Journals Online (AJOL)

Jacques Blessing

The interactions between food and aluminium local kitchen utensils can be a potential source of aluminium released which can ... need to be adopted to preserve consumers' health. ..... Corrosion behaviour of different ... Aluminium beverage.

There is (still too much aluminium in infant formulas

Directory of Open Access Journals (Sweden)

Burrell Shelle-Ann M

2010-08-01

Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

Molybdenum solubility in aluminium nitrate solutions

Energy Technology Data Exchange (ETDEWEB)

Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

2016-07-01

For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

FORMATION REGULARITIES OF PHASE COMPOSITION, STRUCTURE AND PROPERTIES DURING MECHANICAL ALLOYING OF BINARY ALUMINUM COMPOSITES

Directory of Open Access Journals (Sweden)

F. G. Lovshenko

2015-01-01

Full Text Available The paper presents investigation results pertaining to  ascertainment of formation regularities of phase composition and structure during mechanical alloying of binary aluminium composites/substances. The invetigations have been executed while applying a wide range of methods, devices and equipment used in modern material science. The obtained data complement each other. It has been established that presence of oxide and hydro-oxide films on aluminium powder  and introduction of surface-active substance in the composite have significant effect on mechanically and thermally activated phase transformations and properties of semi-finished products.  Higher fatty acids have been used as a surface active substance.The mechanism of mechanically activated solid solution formation has been identified. Its essence is  a formation of  specific quasi-solutions at the initial stage of processing. Mechanical and chemical interaction between components during formation of other phases has taken place along with dissolution  in aluminium while processing powder composites. Granule basis is formed according to the dynamic recrystallization mechanism and possess submicrocrystal structural type with the granule dimension basis less than 100 nm and the grains are divided in block size of not more than 20 nm with oxide inclusions of 10–20 nm size.All the compounds  with the addition of  surface-active substances including aluminium powder without alloying elements obtained by processing in mechanic reactor are disperse hardened. In some cases disperse hardening is accompanied by dispersive and solid solution hardnening process. Complex hardening predetermines a high temperature of recrystallization in mechanically alloyed compounds,  its value exceeds 400 °C.

Niobium-base grain refiner for aluminium

International Nuclear Information System (INIS)

Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

1980-01-01

A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

Mechanical Properties of Spray Cast 7XXX Series Aluminium Alloys

OpenAIRE

SALAMCI, Elmas

2014-01-01

Mechanical properties of spray deposited and extruded 7xxx series aluminium alloys were investigated in peak aged condition. To study the influence of Zn additions on the mechanical behaviour of spray deposited materials, three alloy compositions were selected, namely: SS70 (11.5% Zn), N707 (10.9% Zn) and 7075 (5.6% Zn). After ageing treatment, notched and unnotched specimens of spray deposited alloys were subjected to tensile tests at room temperature. Experimental results showed...

IEC 61267: Feasibility of type 1100 aluminium and a copper/aluminium combination for RQA beam qualities.

Science.gov (United States)

Leong, David L; Rainford, Louise; Zhao, Wei; Brennan, Patrick C

2016-01-01

In the course of performance acceptance testing, benchmarking or quality control of X-ray imaging systems, it is sometimes necessary to harden the X-ray beam spectrum. IEC 61267 specifies materials and methods to accomplish beam hardening and, unfortunately, requires the use of 99.9% pure aluminium (Alloy 1190) for the RQA beam quality, which is expensive and difficult to obtain. Less expensive and more readily available filters, such as Alloy 1100 (99.0% pure) aluminium and copper/aluminium combinations, have been used clinically to produce RQA series without rigorous scientific investigation to support their use. In this paper, simulation and experimental methods are developed to determine the differences in beam quality using Alloy 1190 and Alloy 1100. Additional simulation investigated copper/aluminium combinations to produce RQA5 and outputs from this simulation are verified with laboratory tests using different filter samples. The results of the study demonstrate that although Alloy 1100 produces a harder beam spectrum compared to Alloy 1190, it is a reasonable substitute. A combination filter of 0.5 mm copper and 2 mm aluminium produced a spectrum closer to that of Alloy 1190 than Alloy 1100 with the added benefits of lower exposures and lower batch variability. Copyright © 2015 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Enhanced laminated composite phase change material for energy storage

Energy Technology Data Exchange (ETDEWEB)

Darkwa, J.; Zhou, T. [Centre for Sustainable Energy Technologies (CSET), The University of Nottingham Ningbo, 199 Taikang East Road, Ningbo 315100 (China)

2011-02-15

This paper summarises studies undertaken towards the development of a laminated composite aluminium/hexadecane phase change material (PCM) drywall based on previous analytical work. The study also covered the selection and testing of various types of adhesive materials and identified Polyvinyl acetate (PVA) material as a suitable bonding material. For the purpose of comparison pure hexadecane and composite aluminium/hexadecane samples were developed and tested. The test results revealed faster thermal response by the aluminium/hexadecane sample regarding the rate of heat flux and also achieved about 10% and 15% heat transfer enhancements during the charging and discharging periods respectively. Its measured effective thermal conductivity also increased remarkably to 1.25 W/mK as compared with 0.15 W/mK for pure hexadecane. However there was about 5% less total cumulative thermal energy discharged at the end of the test which indicates that its effective thermal capacity was reduced by the presence of the aluminium particles. The study has shown that some of the scientific and technical barriers associated with the development of laminated composite PCM drywall systems can be overcome but further investigations of effects of adhesive materials are needed. (author)

Remediation of phosphate-contaminated water by electrocoagulation with aluminium, aluminium alloy and mild steel anodes.

Science.gov (United States)

Vasudevan, Subramanyan; Lakshmi, Jothinathan; Jayaraj, Jeganathan; Sozhan, Ganapathy

2009-05-30

The present study provides an electrocoagulation process for the remediation of phosphate-contaminated water using aluminium, aluminium alloy and mild steel as the anodes and stainless steel as the cathode. The various parameters like effect of anode materials, effect of pH, concentration of phosphate, current density, temperature and co-existing ions, and so forth, and the adsorption capacity was evaluated using both Freundlich and Langmuir isotherm models. The adsorption of phosphate preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules. The results showed that the maximum removal efficiency of 99% was achieved with aluminium alloy anode at a current density of 0.2 A dm(-2), at a pH of 7.0. The adsorption process follows second-order kinetics.

A comparative study on low cycle fatigue behaviour of nano and micro Al2O3 reinforced AA2014 particulate hybrid composites

Directory of Open Access Journals (Sweden)

R. Senthilkumar

2015-01-01

Full Text Available Aluminium based metal matrix composites have drawn more attraction due to their improved properties in structural applications for the past two decades. The fatigue behaviour of composite materials needs to be studied for their structural applications. In this work, powder metallurgy based aluminium (AA2014 alloy reinforced with micro and nano-sized alumina particles were fabricated and consolidated with the hot extrusion process. The evaluation of mechanical properties in the extruded composite was carried out. This composite was subjected to low cycle fatigue test with a constant strain rate. Scanning Electron Microscope (SEM and Transmission Electron Microscope (TEM images were used to evaluate the fatigue behaviour of aluminium-nano composite samples. Enhanced mechanical properties were exhibited by the nano alumina reinforced aluminium composites, when compared to the micron sized alumina reinforced composites. The failure cycle is observed to be higher for the nano alumina reinforced composites when compared with micron sized alumina composites due to a lower order of induced plastic strain.

Human biomonitoring of aluminium after a single, controlled manual metal arc inert gas welding process of an aluminium-containing worksheet in nonwelders.

Science.gov (United States)

Bertram, Jens; Brand, Peter; Hartmann, Laura; Schettgen, Thomas; Kossack, Veronika; Lenz, Klaus; Purrio, Ellwyn; Reisgen, Uwe; Kraus, Thomas

2015-10-01

Several existing field studies evaluate aluminium welding works but no thoroughly controlled exposure scenario for welding fume has been described yet. This study provides information about the uptake and elimination of aluminium from welding fumes under controlled conditions. In the Aachen Workplace Simulation Laboratory, we are able to generate welding fumes of a defined particle mass concentration. We exposed 12, until then occupationally unexposed participants with aluminium-containing welding fumes of a metal inert gas (MIG) welding process of a total dust mass concentration of 2.5 mg/m(3) for 6 h. Room air filter samples were collected, and the aluminium concentration in air derived. Urine and plasma samples were collected directly before and after the 6-h lasting exposure, as well as after 1 and 7 days. Human biomonitoring methods were used to determine the aluminium content of the samples with high-resolution continuum source atomic absorption spectrometry. Urinary aluminium concentrations showed significant changes after exposure compared to preexposure levels (mean t(1) (0 h) 13.5 µg/L; mean t(2) (6 h) 23.5 µg/L). Plasma results showed the same pattern but pre-post comparison did not reach significance. We were able to detect a significant increase of the internal aluminium burden of a single MIG aluminium welding process in urine, while plasma failed significance. Biphasic elimination kinetic can be observed. The German BAT of 60 µg/g creatinine was not exceeded, and urinary aluminium returned nearly to baseline concentrations after 7 days.

Multiply-negatively charged aluminium clusters and fullerenes

Energy Technology Data Exchange (ETDEWEB)

Walsh, Noelle

2008-07-15

Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

Irradiation of aluminium alloy materials with electron beam

International Nuclear Information System (INIS)

Konno, Osamu; Masumoto, Kazuyoshi

1982-01-01

It is a theme with a room for discussion to employ the stainless steel composed of longer half-life materials for the vacuum system of accelerators, from the viewpoint of radiation exposure. Therefore, it is desirable to use aluminium of shorter half-life in place of stainless steel. As a result of investigation on the above theme in the 1.2 GeV electron linac project in Tohoku University, it has been concluded that aluminium alloy vacuum chambers can reduce exposure dose by about one or two figures as compared with stainless steel ones. Of course, aluminium alloy contains trace amounts of Mg, Si, Ti, Cr, Mn, Fe, Zn, Cu and others. Therefore, four kinds of aluminium alloy considered to be usable have been examined for induced radioactivity by electron beam irradiation. Stainless steel SUS 304 has been also irradiated for comparison. Radiation energy has been 30 MeV and 200 MeV. When stainless steel and aluminium alloy were compared, aluminium alloy was very effective for reducing surface dose in low energy irradiation. In 200 MeV irradiation, the dose ratio of aluminium alloy to stainless steel became 1/30 to 1/100 after one week, though the dose difference between these two materials became smaller in 100 days or more after irradiation. If practical inspection and repair are implemented during the period from a few days to one week after shutdown, the aluminium alloy is preferable for exposure dose reduction even in high energy irradiation. (Wakatsuki, Y.)

Interfacial reaction between SiC and aluminium due to extrusion and heat treatment process

International Nuclear Information System (INIS)

Junaidah Jai; Fauzi Ismail; Samsiah Sulaiman; Patthi Hussain, Azmi Idris; Yoichi Murakoshi

1999-01-01

Chemical interaction between aluminium (Al) and silicon carbide (SiC) produces aluminium carbide (Al 4 C 3 ) which presents potential problems in the production and application of Al/SiC Metal Matrix Composit (MMC). The Al 4 C 3 formed can reduce material properties such as strength in the MMC. This research work investigates the interface reaction in Al 7075/SiC MMC made through hot extrusion process. Mixed Al 7075/SiC MMC powders were pressed at 300 degree C and extruded at 500 degree C, with a reduction ratio of 20:1. The extruded MMC was then heat-treated in air at various temperatures from 560 degree C, 600 degree C, 640 degree C, 700 degree C to 800 degree C in order to observe the interface reaction of the MMC materials. The heat-treated MMCs were then analyzed under the optical microscope, X-ray Diffraction (XRD) Spectroscope and Scanning Electron Microscope (SEM) with Energy Dispersive X-ray (EDAZ) attachment to observe the interface reaction within the MMCs. This investigation confirms there was interface reaction between SiC and aluminium

Introduction. Aluminium production on electrolytic cells with calcined anodes

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter presents the monograph content, which includes the description of physicochemical processes in aluminium electrolytic cells, and mechanism of electrolytic aluminium obtaining. The short description of aluminium electrolytic cells construction is presented in this book as well.

Aluminium allergy and granulomas induced by vaccinations for children

DEFF Research Database (Denmark)

Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

2014-01-01

Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...

Synthesis and properties of bimetallic aluminium alkoxides

International Nuclear Information System (INIS)

Vyshinskaya, K.I.; Vasil'ev, G.A.; Vishnyakova, T.A.

1997-01-01

A single stage method of aluminium bimetallic alkoxide synthesis, which consists in activated aluminium reaction with metal salts in the relevant alcohols, has been developed. Properties of the compounds prepared are described

Beryllium electrodeposition on aluminium cathode from chloride melts

International Nuclear Information System (INIS)

Nichkov, I.F.; Novikov, E.A.; Serebryakov, G.A.; Kanashin, Yu.P.; Sardyko, G.N.

1980-01-01

Cathodic processes during beryllium deposition on liquid and solid aluminium cathodes are investigated. Mixture of sodium, potassium and beryllium chloride melts served as an lectrolyte. Beryllium ion discharge at the expense of alloy formation takes place at more positive potentials than on an indifferent cathode at low current densities ( in the case of liquid aluminium cathode). Metallographic analysis and measurements of microhardness have shown, that the cathodic product includes two phases: beryllium solid solution in aluminium and metallic beryllium. It is concluded, that aluminium-beryllium alloys with high cathodic yield by current can be obtained by the electrolytic method

Investigation process of alcoholysis of hydride aluminium-adobe

International Nuclear Information System (INIS)

Numanov, M.I.; Normatov, I.Sh.; Mirsaidov, U.M.

2001-01-01

Considering of that process of acid treatment of aluminium-adobe hydride realizes in the ethyl alcohol media it was necessary study the process of alcoholysis of AlH 3 and aluminium additives. In the end of article authors became to conclusion that deficiency of spontaneous alcoholysis of AlH 3 in adobe caused by protective action of fiber; solvate ability of LiCl and alkoxy aluminium hydride of lithium-LiCl·CO 2 H 5 OH, Li Al(OC 2 H 5 ) 4 ·nC 2 H 5 OH decreasing the expectancy of responding of alcohol with aluminium hydride

Analytical study, by modelling methods, of the alkali and alkaline earth cations influence on the stability and the reactivity of aluminium (III) oxides or halides complexes; Etude analytique, par des techniques de modelisation, de l`influence de cations alcalins ou alcalino-terreux sur la stabilite et la reactivite de complexes de l`aluminium(III) avec des ions halogenures ou oxydes

Energy Technology Data Exchange (ETDEWEB)

Bouyer, F

1995-10-05

The electric power consumption in aluminium production and electrorefining processes is high. A study of the electrochemical processes can be very useful for a better understanding of phenomena in electrolytic baths and then for reducing the production costs. A structural and vibrational analysis of species which exist in ionic solutions has been carried out with software based on the functional density theory. Concerning the electrolyte used for the aluminium refining, the anions study has shown that the aluminium chloro-fluoride complexes are preferentially tetrahedral. Moreover, the aluminium oxyfluoride complexes structures (which come from the alumina dissolution in cryolitic media) have been analyzed in the same way and the preferential coordination numbers for aluminium and oxygen have been shown clearly. The anionic model (which is limited to the nearest aluminium neighbours) does not allow to account for the thermodynamics of the cryolitic media. A more elaborated model has then been found to obtain the cryolite structure. The reactions enthalpies have been estimated and have lead to the calculus of species concentration gradients in liquid phase. The counterions effects as for instance sodium and calcium have been investigated. A model for the gaseous phase allowing to know the preferential species has been given. At last, a statistic thermochemistry program has been conceived and developed. It gives the thermodynamical functions at all temperature for the different complexes and allows to reckon the reactions coefficients in gaseous phase as well as the partial pressures profiles with those of calcium and sodium fluorides. (O.M.) 204 refs.

Influence of Process Parameters on the Quality of Aluminium Alloy EN AW 7075 Using Selective Laser Melting (SLM)

Science.gov (United States)

Kaufmann, N.; Imran, M.; Wischeropp, T. M.; Emmelmann, C.; Siddique, S.; Walther, F.

Selective laser melting (SLM) is an additive manufacturing process, forming the desired geometry by selective layer fusion of powder material. Unlike conventional manufacturing processes, highly complex parts can be manufactured with high accuracy and little post processing. Currently, different steel, aluminium, titanium and nickel-based alloys have been successfully processed; however, high strength aluminium alloy EN AW 7075 has not been processed with satisfying quality. The main focus of the investigation is to develop the SLM process for the wide used aluminium alloy EN AW 7075. Before process development, the gas-atomized powder material was characterized in terms of statistical distribution: size and shape. A wide range of process parameters were selected to optimize the process in terms of optimum volume density. The investigations resulted in a relative density of over 99%. However, all laser-melted parts exhibit hot cracks which typically appear in aluminium alloy EN AW 7075 during the welding process. Furthermore the influence of processing parameters on the chemical composition of the selected alloy was determined.

Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

NARCIS (Netherlands)

De Kanter, J.L.C.G.

2006-01-01

Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

International Nuclear Information System (INIS)

Vera, Rosa; Verdugo, Patricia; Orellana, Marco; Munoz, Eduardo

2010-01-01

Research highlights: → The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. → In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. → The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

Aluminium hydroxide-the carrier for catalysts coating

International Nuclear Information System (INIS)

Normatov, I.Sh.; Mirsaidov, U.M.

2003-01-01

At present time several methods of receiving aluminium hydroxide are exist. But all they differ by much staging of process connected with preliminary receiving of intermediate compounds, with application of expensive metallic aluminium

Effects of aluminium surface morphology and chemical modification on wettability

DEFF Research Database (Denmark)

Rahimi, Maral; Fojan, Peter; Gurevich, Leonid

2014-01-01

-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition...... of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...

Simulation of reflectance from white-anodised aluminium surfaces using polyurethane–TiO2 composite coatings

DEFF Research Database (Denmark)

Gudla, Visweswara Chakravarthy; Johansen, Villads Egede; Ambat, Rajan

2015-01-01

of anodised surfaces. PU matrix was selected for its matching refractive-index (n = 1.7) with anodic alumina layer. Three different TiO2 particle size distributions were dispersed in PU and spin coated onto bright high-gloss and matte caustic-etched aluminium substrates. The reflectance spectra of coated...

Proximate and mineral composition of four edible mushroom species

African Journals Online (AJOL)

Owner

Key words: Edible mushrooms; food composition. INTRODUCTION. Mushrooms are saprophytes. ... riboflavin, biotin and thiamine (Chang and Buswell,. 1996). Ogundana and Fagade (1981) indicated that ... Four edible mushroom species were analyzed for food composition according to the Association of Official Analytical ...

Construction of a high-temperature viscosimeter and measurement of the viscosity of melts of the system aluminium-nickel; Aufbau eines Hochtemperaturviskosimeters und Messung der Viskositaet von Schmelzen des Systems Aluminium-Nickel

Energy Technology Data Exchange (ETDEWEB)

Kehr, Mirko

2009-10-29

The system aluminium-nickel is of importance as a model-system in materials science as well as a basic system for superalloys in technical applications. The knowledge of the thermophysical properties of the system aluminium-nickel has been limited to the areas close to the pure elements mainly related to the high melting temperatures of up to 1638 C. The viscosity, which is one of these thermophysical properties, depends on alloy composition as well as on temperature. The viscosity is of importance as an input parameter in computer simulations and for improving casting processes of metallic alloys. The viscosity of aluminium-nickel melts has been measured only once so far. However, not the whole concentration range of the aluminium-nickel system was covered by these data. In particular the viscosity values of the high melting alloys, which are of technological interest, were unknown. The measurement of the missing values was not possible due to the high melting temperatures using existing viscometers. A new oscillating cup viscometer has been constructed within this work. The viscometer has been tested measuring the viscosity values of pure metals, which are well known in literature. The test measurements have been done at temperatures up to 1800 C. A temperature of 2300 C is achievable with slight modifications. A new software for controlling the device and evaluation of the measured data has been developed. Several working equations for calculating the viscosity have been implemented. Furthermore a new approach has been used for detecting the damping of the oscillation of the pendulum containing the liquid sample. The viscosity of aluminium-nickel melts have been measured successfully. The measured values are in good agreement with the little number of known values. A good agreement with values calculated from diffusion experiments and computer simulations was observed as well. Several models for calculating the viscosity of liquid alloys have been tested and

Aluminium removal from water after defluoridation with the electrocoagulation process.

Science.gov (United States)

Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

2015-01-01

Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

Irradiation effects in magnesium and aluminium alloys

International Nuclear Information System (INIS)

Sturcken, E.F.

1979-01-01

Effects of neutron irradiation on microstructure, mechanical properties and swelling of several magnesium and aluminium alloys were studied. The neutron fluences of 2-3 X 10 22 n/cm 2 , >0.2 MeV produced displacement doses of 20 to 45 displacements per atom (dpa). Ductility of the magnesium alloys was severely reduced by irradiation induced recrystallization and precipitation of various forms. Precipitation of transmuted silicon occurred in the aluminium alloys. However, the effect on ductility was much less than for the magnesium alloys. The magnesium and aluminium alloys had excellent resistance to swelling: The best magnesium alloy was Mg/3.0 wt% Al/0.19 wt% Ca; its density decreased by only 0.13%. The best aluminium alloy was 6063, with a density decrease of 0.22%. (Auth.)

Steam Initiated Surface Modification of Aluminium Alloys

DEFF Research Database (Denmark)

Din, Rameez Ud

The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco......, crystalline nano-particles, role of steam-based treatment on adhesion of industrially applied powder coating, and investigations of a failed painted aluminium window profile due to defects in the extruded profile. Chapters 13 and 14 describe the overall discussion, conclusions and future work based...

Diffusion bonding of transition structures for integral aluminium-fibre reinforced polymer (FRP) compounds

Energy Technology Data Exchange (ETDEWEB)

Hehl, A. von [IWT - Stiftung Institut fuer Werkstofftechnik, Hauptabteilung Werkstofftechnik, Bremen (Germany); Syassen, F. [Airbus Operations GmbH, Metal Technology, Bremen (Germany); Schimanski, K.

2012-04-15

Components in hybrid design become more and more important in terms of their lightweight potential. In this context the demand for weight saving in aerospace leads to increasing numbers of applications of fibre composites for primary structural components. In consequence the use of FRP-metal compounds is necessary. Within the investigations of the researcher group ''Schwarz Silber'' (FOR 1224) founded by the DFG (German Research Foundation) material optimised interface structures for advanced CFRP-aluminium compounds are currently being studied. Within their work the researcher group focussed on three concepts realizing the transition structures: the usage of wires (titanium), foils (titanium) and fibres (glass fibre) as transition elements between CFRP and aluminium. For the connection of the aluminium sheet and the transition element die-casting and laser beam welding are basically used. As a possible alternative to the both liquid phase processes a feasibility study haven been done focussing the solid state processes diffusion bonding. The experimental results show the high potential of this process in view of the transferable loads for integral transition structures. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Dielectric aluminium phosphate thin films. Couches minces dielectriques de phosphate d'aluminium

Energy Technology Data Exchange (ETDEWEB)

Daviero, S. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Avinens, C. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Ibanez, A. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Giuntini, J.C. (Lab. Physicochimie des Materiaux Solides, 34 -Montpellier (France)); Philippot, E. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France))

1993-04-01

Aluminium phosphate thin films on silicium substrate have been carried out from tributylphosphate and aluminium acetylacetonate precursors in solution through the ''pyrosol'' process. It can be observed a large range of chemical analysis in terms of experimental conditions. These thin films have been characterized by X-ray diffraction and infrared spectrometry. Their electrical characteristics, defined from direct current and alternative current measurements, are quite different to those of the crystallized phosphate and can be explained by P-O and Al-O ''dangling bond'' existence. (orig.).

Rapidly solidified aluminium for optical applications

NARCIS (Netherlands)

Gubbels, G.P.H.; Venrooy, B.W.H. van; Bosch, A.J.; Senden, R.

2008-01-01

This paper present the results of a diamond turning study of a rapidly solidified aluminium 6061 alloy grade, known as RSA6061. It is shown that this small grain material can be diamond turned to smaller roughness values than standard AA6061 aluminium grades. Also, the results are nearly as good as

Fatty acids composition of 10 microalgal species

Directory of Open Access Journals (Sweden)

Thidarat Noiraksar

2005-11-01

Full Text Available Fatty acids composition of 10 species of microalgae was determined at the exponential phase and the stationary phase. The microalgae consist of two species of diatoms, Bacillariophyceae, (Nitzschia cf. ovalis, Thalassiosira sp. five species of green microalgae, Prasinophyceae (Tetraselmis sp. and Chlorophyceae, (Dictyosphaerium pulchellum, Stichococcus sp., Chlorella sp., Scenedesmus falcatus and three species of blue green microalgae, Cyanophyceae (Anacystis sp., Synechococcus sp., Synechocystis sp..Medium for culture diatoms and green microalgae was F/2, and BG-11 media was used for Cyanophyceae. The microalgae were cultured beneath light intensity 143 μEm-2s-1, light: dark illustration 12:12 hrs., temperature 28ºC, and salinities 8-30 psu. The microalgae were harvested for analyzing fatty acid by centrivugal machine at 3500 rpm. for 5 min. at temperature 20ºC and stored at -80ºC prior to analysis.Fatty acids composition of microalgae differed from species to species. The majority fatty acids composition of diatoms at the exponential phase and the stationary phase were C16:1n-7 (17.12-31.47% and 28.22-42.02%, C16:0 (13.25-19.61% and 18.83-20.67%, C20:5 n-3 (16.65-26.67% and 11.32-23.68% respectively. The principle fatty acids composition of green microalgae, Prasinophyceae, Tetraselmis sp. were C18:3n-3 (16.17-16.67%, C16:0 (15.33-17.45%, C18:1n-9 (12.25-15.43%, C18:2n-6 (9.66-19.97%. The fatty acids composition of green microalgae, Chlorophyceae, were C18:3 n-3 (20.02-26.49% and 15.35- 30.63%, C16:0 (5.76-17.61% and 11.41-20.03%, C18:2n-6 (4.67-17.54% and 7.48-20.61% respectively. The major amounts of fatty acids content of blue green microalgae were C16:1n-7 (9.28-34.91% and 34.48- 35.04%, C14:0 (13.34-25.96% and 26.69-28.24%, C16:0 (5.89-29.15% and 5.70-16.81% except for Anacystis sp.which had a high amount of C18:3 n-3 (23.18-27.98% but low amount of C14:0 (3.66-4.98%.Bacillariophyceae contained the highest amount of highly unsaturated

[Determination of aluminium in flour foods with photometric method].

Science.gov (United States)

Ma, Lan; Zhao, Xin; Zhou, Shuang; Yang, Dajin

2012-05-01

To establish a determination method for aluminium in flour foods with photometric method. After samples being treated with microwave digestion and wet digestion, aluminium in staple flour foods was determined by photometric method. There was a good linearity of the result in the range of 0.25 - 5.0 microg/ml aluminium, r = 0.9998; limit of detection (LOD) : 2.3 ng/ml; limit of quantitation (LOQ) : 7 ng/ml. This method of determining aluminium in flour foods is simple, rapid and reliable.

Comparison of reactivity to a metallic disc and 2% aluminium salt in 366 children, and reproducibility over time for 241 young adults with childhood vaccine-related aluminium contact allergy.

Science.gov (United States)

Gente Lidholm, Anette; Inerot, Annica; Gillstedt, Martin; Bergfors, Elisabet; Trollfors, Birger

2018-07-01

An aluminium hydroxide-adsorbed pertussis toxoid vaccine was studied in 76 000 children in the 1990s in Gothenburg, Sweden. Long-lasting itchy subcutaneous nodules at the vaccination site were seen in 745 participants. Of 495 children with itchy nodules who were patch tested for aluminium allergy, 377 were positive. In 2007-2008, 241 of the positive children were retested. Only in one third were earlier positive results reproduced. To further describe patch test reactions to different aluminium compounds in children with vaccine-induced aluminium allergy. Positive patch test results for metallic aluminium (empty Finn Chamber) and aluminium chloride hexahydrate 2% petrolatum (pet.) were analysed in 366 children with vaccine-induced persistent itching nodules tested in 1998-2002. Of those, 241 were tested a second time (2007-2008), and the patch test results of the two aluminium preparations were analysed. Patch testing with aluminium chloride hexahydrate 2% pet. is a more sensitive way to diagnose aluminium contact allergy than patch testing with metallic aluminium. A general decrease in the strength of reactions to both aluminium preparations in 241 children tested twice was observed. Aluminium contact allergy can be diagnosed by patch testing without using metallic aluminium. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Mechanical properties and corrosion behaviour of MIG welded 5083 aluminium alloy

Energy Technology Data Exchange (ETDEWEB)

Durmus, Huelya [Celal Bayar Univ., Turgutlu-Manisa (Turkey)

2011-07-01

For this study 5083 Aluminium alloy plates, as used in automobiles and watercraft, were experimentally MIG welded. The plates were joined with different wires and at various currents. The effects of welding with different parameters on the mechanical and corrosion properties were investigated. The corrosion behaviour of the MIG welded 5083 Aluminium base material was also investigated. The effects of the chemical composition of the filler material on the mechanical properties were examined by metallographic inspection and tensile testing. By EDS and XRD analyses of specimens it turned out that different structures in the weld metal (Cu3Si) affect its mechanical properties. The mechanical properties of the specimens welded with 5356 filler metal were found as quite well improved as compared to those specimens welded with 4043 and 5183 filler material. The results of the metallographic analysis, and mechanical and corrosion tests exhibited that the 5356 filler material was most suitable for the 5083 Al alloy base material. (orig.)

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

International Nuclear Information System (INIS)

Elabbas, S.; Ouazzani, N.; Mandi, L.; Berrekhis, F.; Perdicakis, M.; Pontvianne, S.; Pons, M-N.; Lapicque, F.; Leclerc, J-P

2016-01-01

Highlights: • COD and Cr(III) species can be simultaneously removed by electrocoagulation. • Cu-containing Al alloy is more efficient than pure Al as electrodes. • Dilution of too concentrated tannery wastewater is required for efficient treatment. - Abstract: This paper deals with the ability of electrocoagulation (EC) to remove simultaneously COD and chromium from a real chrome tanning wastewater in a batch stirred electro-coagulation cell provided with two aluminium-based electrodes (aluminium/copper/magnesium alloy and pure aluminium). Effects of operating time, current density and initial concentration of Cr(III) and COD have been investigated. The concentrations of pollutants have been successfully reduced to environmentally acceptable levels even if the concentrated effluent requires a long time of treatment of around 6 h with a 400 A/m"2 current density. The aluminium alloy was found to be more efficient than pure aluminium for removal of COD and chromium. Dilution of the waste has been tested for treatment: high abatement levels could be obtained with shorter time of treatment and lower current densities. Energy consumption of the electrocoagulation process was also discussed. The dilution by half of the concentrated waste leads to a higher abatement performance of both COD and chromium with the best energy efficiency.

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

Energy Technology Data Exchange (ETDEWEB)

Elabbas, S.; Ouazzani, N.; Mandi, L. [Laboratoire d’Hydrobiologie, Ecotoxicologie et Assainissement (LHEA, URAC 33), Faculté de Sciences Semlalia, BP 2390, Université Cadi Ayyad, Marrakech (Morocco); Centre National d’Etude et de Recherche sur l’Eau et l’Energie (CNEREE), Université Cadi Ayyad, BP 511, Marrakech (Morocco); Berrekhis, F. [Equipe de Physico-chimie des Matériaux, Ecole Normale Supérieure, Université Cadi Ayyad, BP 2400, 40000 Marrakech (Morocco); Perdicakis, M. [Laboratoire de Chimie Physique et Microbiologie pour l’Environnement (LCPME) UMR 7564, Université de Lorraine—CNRS, 405 rue de Vandoeuvre, F-54602 Villers-lès Nancy Cedex (France); Pontvianne, S.; Pons, M-N.; Lapicque, F. [Laboratoire Réactions et Génie des Procédés (LRGP) UMR 7274, CNRS, Université de Lorraine, 1 rue Grandville, BP 20451, 54001 Nancy cedex (France); Leclerc, J-P, E-mail: jean-pierre.leclerc@univ-lorraine.fr [Laboratoire Réactions et Génie des Procédés (LRGP) UMR 7274, CNRS, Université de Lorraine, 1 rue Grandville, BP 20451, 54001 Nancy cedex (France)

2016-12-05

Highlights: • COD and Cr(III) species can be simultaneously removed by electrocoagulation. • Cu-containing Al alloy is more efficient than pure Al as electrodes. • Dilution of too concentrated tannery wastewater is required for efficient treatment. - Abstract: This paper deals with the ability of electrocoagulation (EC) to remove simultaneously COD and chromium from a real chrome tanning wastewater in a batch stirred electro-coagulation cell provided with two aluminium-based electrodes (aluminium/copper/magnesium alloy and pure aluminium). Effects of operating time, current density and initial concentration of Cr(III) and COD have been investigated. The concentrations of pollutants have been successfully reduced to environmentally acceptable levels even if the concentrated effluent requires a long time of treatment of around 6 h with a 400 A/m{sup 2} current density. The aluminium alloy was found to be more efficient than pure aluminium for removal of COD and chromium. Dilution of the waste has been tested for treatment: high abatement levels could be obtained with shorter time of treatment and lower current densities. Energy consumption of the electrocoagulation process was also discussed. The dilution by half of the concentrated waste leads to a higher abatement performance of both COD and chromium with the best energy efficiency.

Study of corrosion in aluminium using neutron radiography technique

International Nuclear Information System (INIS)

Islam, M.N.; Alam, M.K.; Saklayen, M.A.; Ahsan, M.H.; Islam, S.M.A.; Zaman, M.A.

2000-01-01

Neutron radiography technique has been adopted for detection of corrosion in aluminium by filling artificially made holes on aluminium slab with Al(OH) 3 . The contrast between the optical densities of corrosion products and aluminium slab was assessed from the densitometric measurements. Variation of optical density difference with sample thickness has also been studied. The results confirm that approximately 0.039 mm thick corrosion products having diameter 10 mm can easily be detected in 2 cm thick aluminium slab. The linear attenuation coefficient of Al(OH) 3 has been obtained as 0.9447. From the present investigation it is confirmed that film neutron radiography (NR) technique is helpful for investigation of Al(OH) 3 type corrosion product in aluminium. (author)

Aluminium based amorphous and nanocrystalline structure

Energy Technology Data Exchange (ETDEWEB)

Sitek, Jozef; Degmova, Jarmila, E-mail: jarmila.degmova@stuba.sk [Slovak University of Technology, Department of Nuclear Physics and Technology, Faculty of Electrical Engineering and Information Technology (Slovakia)

2005-09-15

Aluminium based rapidly quenched alloys of nominal composition Al{sub 90}Fe{sub 7}Nb{sub 3} and Al{sub 94}Fe{sub 2}V{sub 4} were studied by Moessbauer spectroscopy. Samples annealed up to 573 K showed amorphous structure represented by quadrupole doublet. From corrected spectra areas the values of f-factor were calculated. In the case of AlFeNb samples f-factor was estimated as f = 0.26 and for AlFeV f = 0.31. The corresponding Debye temperatures were also calculated. Higher temperature annealing at 773 and 873 K induced deformation of nano- and microcrystalline state. Moessbauer spectra of samples of both compositions (with vanadium as well as with niobium) annealed at 773 K showed superposition of crystalline phases with dominant role of Al{sub 3}Fe alloy. During annealing at 873 K, phases with large grains and small amount of FeAl metastable phase were developed (Das et al. Mat. Sci. Eng., A304-A306, 159, 2001; Illekova et al. Mat. Sci. Eng., A375-A377, 946, 2004).

Aluminium based amorphous and nanocrystalline structure

International Nuclear Information System (INIS)

Sitek, Jozef; Degmova, Jarmila

2005-01-01

Aluminium based rapidly quenched alloys of nominal composition Al 90 Fe 7 Nb 3 and Al 94 Fe 2 V 4 were studied by Moessbauer spectroscopy. Samples annealed up to 573 K showed amorphous structure represented by quadrupole doublet. From corrected spectra areas the values of f-factor were calculated. In the case of AlFeNb samples f-factor was estimated as f = 0.26 and for AlFeV f = 0.31. The corresponding Debye temperatures were also calculated. Higher temperature annealing at 773 and 873 K induced deformation of nano- and microcrystalline state. Moessbauer spectra of samples of both compositions (with vanadium as well as with niobium) annealed at 773 K showed superposition of crystalline phases with dominant role of Al 3 Fe alloy. During annealing at 873 K, phases with large grains and small amount of FeAl metastable phase were developed (Das et al. Mat. Sci. Eng., A304-A306, 159, 2001; Illekova et al. Mat. Sci. Eng., A375-A377, 946, 2004).

Effects of aluminium surface morphology and chemical modification on wettability

Energy Technology Data Exchange (ETDEWEB)

Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

2014-03-01

Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

Spectrophotometric determination of aluminium in steel with xylenol orange

International Nuclear Information System (INIS)

Majeed, A.; Javed, N.; Khan, M.S.

1996-01-01

Spectrophotometric determination of Aluminium in steel based on colour reaction between Aluminium and xylenol orange has been carried out. Red coloured complex formed in weak acidic solution is measured for its absorbance at 550 nm. The various optimum experimental conditions for Aluminium xylenol orange (Al-Xo) complex have been studied. (author)

Influence of aluminium incorporation on the structure of ZrN films deposited at low temperatures

International Nuclear Information System (INIS)

Araiza, J J; Sanchez, O

2009-01-01

We have studied the influence of Al incorporation in the crystalline structure of ZrN thin films deposited by dc magnetron sputtering at low temperature. The amount of aluminium in the films depends directly on the power applied to the aluminium cathode during the deposition. Energy dispersive x-ray analysis and x-ray diffraction (XRD) were used to obtain the chemical composition and crystalline structure of the films, respectively. When Al atoms are incorporated into the ZrN coatings, the strong ZrN (2 0 0) orientation is modified by a combination of other ones such as ZrN (1 1 1), Zr 3 N 4 (2 1 1) and hexagonal AlN (1 0 0) as detected from the XRD spectra for high aluminium concentrations. Fourier-transform infrared spectroscopy allowed us to identify oxides and nitrides, ZrO, AlO and AlN, incorporated into the deposited films. The effect of a bias voltage applied to the substrate has also been investigated and related to the changes in the microstructure and in the nanohardness values of the ZrAlN films.

Degradation of unglazed rough graphite-aluminium solar absorber surfaces in simulated acid and neutral rain

International Nuclear Information System (INIS)

Konttinen, P.; Lund, P.D.; Salo, T.

2005-01-01

Degradation mechanisms of unglazed solar absorber surfaces based on aluminium substrate were studied. Rough graphite-aluminium surfaces were total-immersion subjected to aerated and de-aerated simulated neutral and acid rain. Test conditions were based on calculated absorber stagnation temperature and global rain acidity measurements. Changes in optical properties, elemental composition and sample mass were examined by spectrometry, energy dispersive X-ray spectrometry and thermogravimetry, respectively. The absorbers exhibited almost no degradation at pH value of 3.5. At pH 5.5 alumina on the surface hydrated significantly degrading the optical properties of the surfaces severely in most cases. Therefore these absorber surfaces can not be recommended to be used in non-glazed applications if they are exposed to rain with pH exceeding ∼ 3.5-4.5. The total-immersion test needs to be developed further as the test results exhibited poor temperature and time dependency thus preventing accurate service lifetime estimates. Still, these tests were useful in determining favourable and non-favourable operating conditions for the absorber surfaces based on aluminium substrate. (author)

Essential oil composition of four Artemisia species from Ethiopia

Directory of Open Access Journals (Sweden)

N. Asfaw

2015-01-01

Full Text Available The essential oil composition of four Artemisia species, namely A. schimperi Sch. Bip. ex Engl. A. abyssinica Sch. Bip. ex A. Rich., A. afra Jacq. ex Willd., and A. absinthium L. (previously called A. rehan from Ethiopia has been studied. The essential oil obtained from A. absinthium (seedling from Europe grown in two places in Ethiopia (Addis Ababa and Butajira was also analyzed for comparison. Morphological study on the leaves of A. absinthium L. from Ethiopia (previously called A. rehan and A. absinthium (from Europe was also conducted. The essential oils were obtained by hydrodistillation using a Clevenger apparatus and analyzed by capillary GC and GC/MS. Forty three compounds representing 76 to 94% of the oils were identified. The composition of the essential oils of A. schimperi, A. afra and A. abyssinica are mainly dominated by irregular monoterpenes: yogomi alcohol (13.5-37.6%, artemisyl acetate (12.7-35.5%, and artemisia ketone (2.3-13.2%. The composition of the oil of A. absinthium (previously A. rehan however, differs from the other three species in having camphor (21.2-28.3% and davanone (21.3-26.5% as major components. The composition of A. absinthum (Europe was found to have β-thujone (42.3-66.4% and chamazulene (11.3-24.2% as major components. The study indicated that the composition of the essential oil of A. absinthium (previously A. rehan is not only different from the other three species but also from A. absinthium from Europe and does not belong to any of the chemotypes described for the species in the literature. The morphological study on the leaves also showed that it differs from that of A. absinthium from Europe. DOI: http://dx.doi.org/10.4314/bcse.v29i1.11

Aluminium Electrodeposition from Ionic Liquid: Effect of Deposition Temperature and Sonication †

Directory of Open Access Journals (Sweden)

Enrico Berretti

2016-08-01

Full Text Available Since their discovery, ionic liquids (ILs have attracted a wide interest for their potential use as a medium for many chemical processes, in particular electrochemistry. As electrochemical media they allow the electrodeposition of elements that are impossible to reduce in aqueous media. We have investigated the electrodeposition of aluminium from 1-butyl-3-methyl-imidazolium chloride ((BmimCl/AlCl3 (40/60 mol % as concerns the effect of deposition parameters on the quality of the deposits. Thick (20 μm aluminium coatings were electrodeposited on brass substrates at different temperatures and mixing conditions (mechanical stirring and sonication. These coatings were investigated by means of scanning electron microscope, roughness measurements, and X-ray diffraction to assess the morphology and the phase composition. Finally, electrochemical corrosion tests were carried out with the intent to correlate the deposition parameters to the anti-corrosion properties.

Study of ionic movements during anodic oxidation of nitrogen-implanted aluminium

International Nuclear Information System (INIS)

Terwagne, G.; Lucas, S.; Bodart, F.; Sorensen, G.; Jensen, H.

1990-01-01

In recent years there has been a considerable interest in synthesizing aluminium nitrides by ion implantation in order to modify the tribological properties of aluminium. The growth of an oxide layer by anodic process on these synthesized aluminium nitrides gives an interesting oxide-on-semiconductor material with surprising dynamic and decorative properties. During the anodic oxidation, ionic movements are involved in the near-surface region of the aluminium material; these ionic movements have been studied by Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA) on thin aluminium foils (7000 A) preimplanted with nitrogen and post-oxidized in an ammonium pentaborate solution. The growth of the oxide layer is reduced when the aluminium is preimplanted with nitrogen: the speed of oxidation depends on the implantation conditions (energy and fluence). Moreover, the aluminium nitride can be dissolved when all metallic aluminium staying between the surface and the AlN are consumed by the anodic process. (orig.)

Modern tree species composition reflects ancient Maya "forest gardens" in northwest Belize.

Science.gov (United States)

Ross, Nanci J

2011-01-01

Ecology and ethnobotany were integrated to assess the impact of ancient Maya tree-dominated home gardens (i.e., "forest gardens"), which contained a diversity of tree species used for daily household needs, on the modern tree species composition of a Mesoamerican forest. Researchers have argued that the ubiquity of these ancient gardens throughout Mesoamerica led to the dominance of species useful to Maya in the contemporary forest, but this pattern may be localized depending on ancient land use. The tested hypothesis was that species composition would be significantly different between areas of dense ancient residential structures (high density) and areas of little or no ancient settlement (low density). Sixty-three 400-m2 plots (31 high density and 32 low density) were censused around the El Pilar Archaeological Reserve in northwestern Belize. Species composition was significantly different, with higher abundances of commonly utilized "forest garden" species still persisting in high-density forest areas despite centuries of abandonment. Subsequent edaphic analyses only explained 5% of the species composition differences. This research provides data on the long-term impacts of Maya forests gardens for use in development of future conservation models. For Mesoamerican conservation programs to work, we must understand the complex ecological and social interactions within an ecosystem that developed in intimate association with humans.

Structure analysis of aluminium silicon manganese nitride precipitates formed in grain-oriented electrical steels

International Nuclear Information System (INIS)

Bernier, Nicolas; Xhoffer, Chris; Van De Putte, Tom; Galceran, Montserrat; Godet, Stéphane

2013-01-01

We report a detailed structural and chemical characterisation of aluminium silicon manganese nitrides that act as grain growth inhibitors in industrially processed grain-oriented (GO) electrical steels. The compounds are characterised using energy dispersive X-ray spectrometry (EDX) and energy filtered transmission electron microscopy (EFTEM), while their crystal structures are analysed using X-ray diffraction (XRD) and TEM in electron diffraction (ED), dark-field, high-resolution and automated crystallographic orientation mapping (ACOM) modes. The chemical bonding character is determined using electron energy loss spectroscopy (EELS). Despite the wide variation in composition, all the precipitates exhibit a hexagonal close-packed (h.c.p.) crystal structure and lattice parameters of aluminium nitride. The EDX measurement of ∼ 900 stoichiometrically different precipitates indicates intermediate structures between pure aluminium nitride and pure silicon manganese nitride, with a constant Si/Mn atomic ratio of ∼ 4. It is demonstrated that aluminium and silicon are interchangeably precipitated with the same local arrangement, while both Mn 2+ and Mn 3+ are incorporated in the h.c.p. silicon nitride interstitial sites. The oxidation of the silicon manganese nitrides most likely originates from the incorporation of oxygen during the decarburisation annealing process, thus creating extended planar defects such as stacking faults and inversion domain boundaries. The chemical composition of the inhibitors may be written as (AlN) x (SiMn 0.25 N y O z ) 1−x with x ranging from 0 to 1. - Highlights: • We study the structure of (Al,Si,Mn)N inhibitors in grain oriented electrical steels. • Inhibitors have the hexagonal close-packed symmetry with lattice parameters of AlN. • Inhibitors are intermediate structures between pure AlN and (Si,Mn)N with Si/Mn ∼ 4. • Al and Si share the same local arrangement; Mn is incorporated in both Mn 2+ and Mn 3+ . • Oxygen

Aluminium exclusion and aluminium tolerance in woody plants

Directory of Open Access Journals (Sweden)

Ivano eBrunner

2013-06-01

Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

Corrosion behaviour of borated aluminium used as neutron absorber

Energy Technology Data Exchange (ETDEWEB)

Emmerich, R. [EaglePicher Technologies GmbH, Oehringen (Germany); Ensinger, W.; Enders, B. [Philipps-Univ. of Marburg, Dept. of Chemistry, Material Science Centre (Germany)

2004-07-01

The electrochemical behaviour of pure and borated aluminium was examined. Measurements were performed in two different electrolytes at 90 C containing different trace-amounts of chloride. For borated aluminium current transients, i.e. metastable depassivation events were found. It is suggested to attribute these transients to less stable passivation layers in comparison to pure aluminium.

Effects of Aluminium Sulfate on Cadmium Accumulation in Rice

International Nuclear Information System (INIS)

Khamvarn, Vararas; Boontanon, Narin; Prapagdee, Benjaphorn; Kumsopa, Acharaporn; Boonsirichai, Kanokporn

2011-06-01

Full text: Cadmium accumulation in Pathum Thani 1 and Suphan Buri 60 rice cultivars was investigated upon treatment with aluminium sulfate as a precipitant. Rice was grown hydroponically in a medium containing 4 ppm cadmium nitrate with or without 4 ppm aluminium sulfate. Root, stem with leaves and grain samples were collected and analyzed for cadmium content using atomic absorption spectroscopy and inductively coupled plasma atomic emission spectroscopy. Without the addition of aluminium sulfate, Pathum Thani 1 and Suphan Buri 60 accumulated 24.71∫ 3.14 ppm and 34.43 ∫ 4.51 ppm (dry weight of whole plant) of cadmium, respectively. With aluminium sulfate, cadmium accumulation increased to 40.66 ∫ 2.47 ppm and 62.94 ∫ 10.69 ppm, respectively. The addition of aluminium sulfate to the planting medium did not reduce cadmium accumulation but caused the rice to accumulate more cadmium especially in the shoots and grains. This observation might serve as the basis for future research on the management of agricultural areas that are contaminated with cadmium and aluminium

Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

International Nuclear Information System (INIS)

Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

2012-01-01

Highlights: ► Aluminium packaging partitioning in MSW incineration residues is evaluated. ► The amount of aluminium packaging recoverable from the bottom ashes is evaluated. ► Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. ► 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

Electron Conditioning of Technical Aluminium Surfaces

Energy Technology Data Exchange (ETDEWEB)

Le Pimpec, F

2004-09-02

The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (= 1.3, value of many pure elements [1]), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

Determination of ultratrace amounts of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization/ICP-MS

International Nuclear Information System (INIS)

Nakamura, Yasushi; Kobayashi, Yoshio; Kakurai, Yousuke

1993-01-01

A method has been developed for determining the 0.01 ng g -1 level of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization (ETV)/ICP-MS. This method was found to be significantly interfered with any matrices or other elements contained. An ion-exchange technique was therefore applied to separate uranium and thorium from aluminium and other elements. It was known that uranium are adsorbed on an anion-exchange resin and thorium are adsorbed on cation-exchange resin. However, aluminium and copper were eluted with 6 M hydrochloric acid. Dissolve the sample with hydrochloric acid containing copper which was added for analysis of pure aluminium, and oxidize with hydrogen peroxide. Concentration of hydrochloric acid in the solution was adjusted to 6 M, and then passed the solution through the mixed ion-exchange resin column. After the uranium and thorium were eluted with 1 M hydrofluoric acid-0.1 M hydrochloric acid, the solution was evaporated to dryness. It was then dissolved with 1 M hydrochloric acid. Uranium and thorium were analyzed by ETV/ICP-MS using tungsten and molybdenum boats, respectively, since the tungsten boat contained high-level thorium and the molybdenum boat contained uranium. The determination limit of uranium and thorium were 0.003 and 0.005 ng g -1 , respectively. (author)

Aluminium and copper analysis in metallic alloys by neutron activation analysis from an 241 Am-Be source

International Nuclear Information System (INIS)

Carvalho, J. de.

1980-01-01

Aluminium and copper have been determined in aluminium alloys by the method of activation with neutrons from an 241 Am-Be source of intensity 9,8 x 10 6 n/s. The activity induced due to reactions 27 Al (n, γ) 28 Al and 63 Cu (n, γ) 64 Cu have been measured with a NaI (Tl) detector coupled to a single channel system. In order to obtain the samples and standards of about the same composition, the material to be irradiated was powdered. In view of low intensity of neutron source it was necessary to use samples of up to 50 g. A series of preliminary irradiations were carried out to ensure that the geometry for the irradiation and for the counting are reproducible. The results have been compared with those obtained by chemical methods. Assuming that the results obtained by chemical method is exact, a maximum relative error of 3,6% is obtained by this method. The method has a good reproducibility. The time needed for analysis of aluminium and copper are 18 min and 2 hours 40 minutes respectively. Four different samples were analysed. The average of five measurements for one of the samples was: 88.0% for aluminium and 10.0% for copper. The standard deviation and coefficient of variation were 0,8 and 1.0% for aluminium and 0,2 and 2.0% for copper. (author)

Investigations concerning the effect of aluminium toxicity on the physiology and fine structures of oat plants. Physiologische und feinstrukturelle Untersuchungen zur Aluminium-Toxizitaet an Haferpflanzen

Energy Technology Data Exchange (ETDEWEB)

Marienfeld, S.

1992-06-30

In order to test the toxicity of aluminium to plants, two-week-old oat seedlings were exposed to aluminium concentrations of 0-400 [mu]M in the culture broth. Already after 12-24 hours a decrease in longitudinal root growth is to be noted, resulting from impaired mitosis activity of the root tip. This, and the observed premature cell differentiation are not aluminium-specific but unspecific reactions to unfavourable conditions. Shoot growth is only reduced after 3-4 days, and less so. Magnesium and calcium fertilization did enhance the growth of aluminium-stressed plants, but not to the level of the control plants, although the mineral concentration in the leaves reached normal values. Phosphate concentration in the root increased because of aluminium phosphate precipitation in the cell walls, which has detoxifying effect along with aluminium fixation to negative charges in the cell walls. Aluminium remains almost quantitatively in the cell wall area of the roots and is not accumulated in the cell core. Aluminium stress causes transpiration and CO[sub 2] uptake to be impaired as a reaction to the growth depression in the root area, even before the mineral concentration in the shoots is lowered. Later there follow chlorophyll depletion, chloroplast degradation, and a reduction of the leaf area. (UWA)

Friction stir welding (FSW of aluminium foam sandwich panels

Directory of Open Access Journals (Sweden)

M. Bušić

2016-07-01

Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

Surface treatments for aluminium alloys

Science.gov (United States)

Ardelean, M.; Lascău, S.; Ardelean, E.; Josan, A.

2018-01-01

Typically, in contact with the atmosphere, the aluminium surface is covered with an aluminium oxide layer, with a thickness of less than 1-2μm. Due to its low thickness, high porosity and low mechanical strength, this layer does not protect the metal from corrosion. Anodizing for protective and decorative purposes is the most common method of superficial oxidation processes and is carried out through anodic oxidation. The oxide films, resulted from anodizing, are porous, have a thickness of 20-50μm, and are heat-resistant, stable to water vapour and other corrosion agents. Hard anodizing complies with the same obtains principles as well as decorative and protective anodization. The difference is in that hard anodizing is achieved at low temperatures and high intensity of electric current. In the paper are presented the results of decorative and hard anodization for specimens made from several aluminium alloys in terms of the appearance of the specimens and of the thickness of the anodized.

Accumulation of Aluminium and Physiological Status of Tree Foliage in the Vicinity of a Large Aluminium Smelter

Directory of Open Access Journals (Sweden)

E. D. Wannaz

2012-01-01

Full Text Available A pollution gradient was observed in tree foliage sampled in the vicinity of a large aluminium production facility in Patagonia (Argentina. Leaves of Eucalyptus rostrata, and Populus hybridus and different needle ages of Pinus spec. were collected and concentrations of aluminium (Al and sulphur (S as well as physiological parameters (chlorophyll and lipid oxidation products were analyzed. Al and S concentrations indicate a steep pollution gradient in the study showing a relationship with the physiological parameters in particular membrane lipid oxidation products. The present study confirms that aluminium smelting results in high Al and sulphur deposition in the study area, and therefore further studies should be carried out taking into account potentially adverse effects of these compounds on human and ecosystem health.

A well-defined silica-supported aluminium alkyl through an unprecedented, consecutive two-step protonolysis–alkyl transfer mechanism

KAUST Repository

Pelletier, Jé ré mie; Espinas, Jeff; Vu, Nghiem; Norsic, Sé bastien; Baudouin, Anne; Delevoye, Laurent; Tré bosc, Julien; Le Roux, Erwan; Santini, Catherine; Basset, Jean-Marie; Gauvin, Ré gis M.; Taoufik, Mostafa

2011-01-01

Impregnation of [(AliBu3)(Et2O)] on partially dehydroxylated SBA-15 affords a mesoporous material bearing the well-defined single site surface aluminium species [(≡SiO)2Al(iBu)(Et 2O)]. © The Royal Society of Chemistry.

Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part I Microstructural investigation

DEFF Research Database (Denmark)

Din, Rameez Ud; Piotrowska, Kamila; Gudla, Visweswara Chakravarthy

2015-01-01

The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment ...

Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

Energy Technology Data Exchange (ETDEWEB)

Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy); Gorla, Leopoldo; Nessi, Simone; Grosso, Mario [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy)

2012-12-15

Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

Aluminium allergy and granulomas induced by vaccinations for children

DEFF Research Database (Denmark)

Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

2014-01-01

Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

Fish species composition, density-distribution patterns, and impingement during upwelling

International Nuclear Information System (INIS)

Spigarelli, S.A.; Sharma, R.K.

1975-01-01

The effects of cooling system intakes and discharges on Lake Michigan fishes are highly dependent on inshore species composition and spatial distribution which, in turn, are affected by natural hydrological conditions. Significant (5 to 10 C) short-term decreases in water temperature (due to upwelling) could cause cold shock in fish equilibrated to either ambient or plume temperatures; substantial changes in distribution due to avoidance or attraction responses; and resultant changes in susceptibility to impingement. The objectives of this study are to characterize the changes in fish species composition, density, and thermal distribution as a result of natural upwellings, and to relate these factors to intake and discharge effects. Day and night sampling was conducted in ambient (reference) and thermal plume waters near the Zion Nuclear Plant on four occasions between 17 July and 11 September 1975. Density-distribution patterns and species composition of fish were determined by means of gill nets, bottom trawls, seines, and a sonic fish locater

Recoil-free Fraction in Amorphous and Nanocrystalline Aluminium Based Alloys

Science.gov (United States)

Sitek, Jozef

2008-10-01

Aluminium based rapidly quenched alloys of nominal composition Al90Fe7Nb3 and Al94Fe2V4 were studied by Mössbauer spectroscopy. We have measured the recoil-free fraction and thermal shift at room and liquid nitrogen temperature. The frequency modes of atomic vibrations were determined and consequently the characteristic Debye temperature was derived. Characteristic temperature calculated from f-factor was lower than those fitted from second order Doppler shift. This indicates the presence of different frequency modes for amorphous and nanocrystalline states.

Hot workability of aluminium alloys

International Nuclear Information System (INIS)

Yoo, Yeon Chul; Oh, Kyung Jin

1986-01-01

Hot Workability of aluminium alloys, 2024, 6061 and 7075, has been studied by hot torsion tests at temperatures from 320 to 515 deg C and at strain rates from 1.26 x 10 -3 to 5.71 x 10 -3 sec -1 . Hot working condition of these aluminium alloys was determined quantitatively from the constitutive equations obtained from flow stress curves in torsion. Experimental data of the logarith of the Zener-Hollomonn parameter showed good linear relationships to the logarith of sinh(ασ-bar)

Iron and aluminium oxides containing industrial wastes as adsorbents of heavy metals: Application possibilities and limitations.

Science.gov (United States)

Jacukowicz-Sobala, Irena; Ociński, Daniel; Kociołek-Balawejder, Elżbieta

2015-07-01

Industrial wastes with a high iron or aluminium oxide content are produced in huge quantities as by-products of water treatment (water treatment residuals), bauxite processing (red mud) and hard and brown coal burning in power plants (fly ash). Although they vary in their composition, the wastes have one thing in common--a high content of amorphous iron and/or aluminium oxides with a large specific surface area, whereby this group of wastes shows very good adsorbability towards heavy metals, arsenates, selenates, etc. But their physical form makes their utilisation quite difficult, since it is not easy to separate the spent sorbent from the solution and high bed hydraulic resistances occur in dynamic regime processes. Nevertheless, because of the potential benefits of utilising the wastes in industrial effluent treatment, this issue attracts much attention today. This study describes in detail the waste generation processes, the chemical structure of the wastes, their physicochemical properties, and the mechanisms of fixing heavy metals and semimetals on the surface of iron and aluminium oxides. Typical compositions of wastes generated in selected industrial plants are given. A detailed survey of the literature on the adsorption applications of the wastes, including methods of their thermal and chemical activation, as well as regeneration of the spent sorbents, is presented. The existing and potential ways of modifying the physical form of the discussed group of wastes, making it possible to overcome the basic limitation on their practical use, are discussed. © The Author(s) 2015.

Aluminium toxicity tolerance in crop plants: Present status of research

African Journals Online (AJOL)

... tolerance of which genes of the Aluminium-activated malate transporter (ALMT) and multidrug and toxic compound extrusion (MATE) families are prominent. In this review, the progress of research in identifying aluminium toxicity tolerant genes is discussed. Keywords: Aluminium toxicity, soil acidity, hydroponic screening, ...

Remnant trees affect species composition but not structure of tropical second-growth forest.

Science.gov (United States)

Sandor, Manette E; Chazdon, Robin L

2014-01-01

Remnant trees, spared from cutting when tropical forests are cleared for agriculture or grazing, act as nuclei of forest regeneration following field abandonment. Previous studies on remnant trees were primarily conducted in active pasture or old fields abandoned in the previous 2-3 years, and focused on structure and species richness of regenerating forest, but not species composition. Our study is among the first to investigate the effects of remnant trees on neighborhood forest structure, biodiversity, and species composition 20 years post-abandonment. We compared the woody vegetation around individual remnant trees to nearby plots without remnant trees in the same second-growth forests ("control plots"). Forest structure beneath remnant trees did not differ significantly from control plots. Species richness and species diversity were significantly higher around remnant trees. The species composition around remnant trees differed significantly from control plots and more closely resembled the species composition of nearby old-growth forest. The proportion of old-growth specialists and generalists around remnant trees was significantly greater than in control plots. Although previous studies show that remnant trees may initially accelerate secondary forest growth, we found no evidence that they locally affect stem density, basal area, and seedling density at later stages of regrowth. Remnant trees do, however, have a clear effect on the species diversity, composition, and ecological groups of the surrounding woody vegetation, even after 20 years of forest regeneration. To accelerate the return of diversity and old-growth forest species into regrowing forest on abandoned land, landowners should be encouraged to retain remnant trees in agricultural or pastoral fields.

Tree species composition within Kano State University of science ...

African Journals Online (AJOL)

The study accessed the tree species composition within the Kano State University of Science and Technology Wudil, Kano State, Nigeria with the view of providing information that will help in the management and conservation of tree species within the campus. The study area was stratified into four (4) sections from which ...

Compressive Behaviour and Energy Absorption of Aluminium Foam Sandwich

Science.gov (United States)

Endut, N. A.; Hazza, M. H. F. Al; Sidek, A. A.; Adesta, E. T. Y.; Ibrahim, N. A.

2018-01-01

Development of materials in automotive industries plays an important role in order to retain the safety, performance and cost. Metal foams are one of the idea to evolve new material in automotive industries since it can absorb energy when it deformed and good for crash management. Recently, new technology had been introduced to replace metallic foam by using aluminium foam sandwich (AFS) due to lightweight and high energy absorption behaviour. Therefore, this paper provides reliable data that can be used to analyze the energy absorption behaviour of aluminium foam sandwich by conducting experimental work which is compression test. Six experiments of the compression test were carried out to analyze the stress-strain relationship in terms of energy absorption behavior. The effects of input variables include varying the thickness of aluminium foam core and aluminium sheets on energy absorption behavior were evaluated comprehensively. Stress-strain relationship curves was used for energy absorption of aluminium foam sandwich calculation. The result highlights that the energy absorption of aluminium foam sandwich increases from 12.74 J to 64.42 J respectively with increasing the foam and skin thickness.

Investigation of different anode materials for aluminium rechargeable batteries

Science.gov (United States)

Muñoz-Torrero, David; Leung, Puiki; García-Quismondo, Enrique; Ventosa, Edgar; Anderson, Marc; Palma, Jesús; Marcilla, Rebeca

2018-01-01

In order to shed some light into the importance of the anodic reaction in reversible aluminium batteries, we investigate here the electrodeposition of aluminium in an ionic liquid electrolyte (BMImCl-AlCl3) using different substrates. We explore the influence of the type of anodic material (aluminium, stainless steel and carbon) and its 3D geometry on the reversibility of the anodic reaction by cyclic voltammetry (CV) and galvanostatic charge-discharge. The shape of the CVs confirms that electrodeposition of aluminium was feasible in the three materials but the highest peak currents and smallest peak separation in the CV of the aluminium anode suggested that this material was the most promising. Interestingly, carbon-based substrates appeared as an interesting alternative due to the high peak currents in CV, moderate overpotentials and dual role as anode and cathode. 3D substrates such as fiber-based carbon paper and aluminium mesh showed significantly smaller overpotentials and higher efficiencies for Al reaction suggesting that the use of 3D substrates in full batteries might result in enhanced power. This is corroborated by polarization testing of full Al-batteries.

Changes in Species Richness and Composition of Tiger Moths (Lepidoptera: Erebidae: Arctiinae) among Three Neotropical Ecoregions

Science.gov (United States)

Beccacece, Hernán Mario; Zeballos, Sebastián Rodolfo; Zapata, Adriana Inés

2016-01-01

Paraná, Yungas and Chaco Serrano ecoregions are among the most species-rich terrestrial habitats at higher latitude. However, the information for tiger moths, one of the most speciose groups of moths, is unknown in these ecoregions. In this study, we assess their species richness and composition in all three of these ecoregions. Also we investigated whether the species composition of tiger moths is influenced by climatic factors and altitude. Tiger moth species were obtained with samples from 71 sites using standardized protocols (21 sites were in Yungas, 19 in Paraná and 31 in Chaco Serrano). Rarefaction-extrapolation curves, non-parametric estimators for incidence and sample coverage indices were performed to assess species richness in the ecoregions studied. Non metric multidimensional scaling and adonis tests were performed to compare the species composition of tiger moths among ecoregions. Permutest analysis and Pearson correlation were used to evaluate the relationship among species composition and annual mean temperature, annual temperature range, annual precipitation, precipitation seasonality and altitude. Among ecoregions Paraná was the richest with 125 species, followed by Yungas with 63 species and Chaco Serrano with 24 species. Species composition differed among these ecoregions, although Yungas and Chaco Serrano were more similar than Paraná. Species composition was significantly influenced by climatic factors and altitude. This study showed that species richness and species composition of tiger moths differed among the three ecoregions assessed. Furthermore, not only climatic factors and altitude influence the species composition of tiger moths among ecoregions, but also climatic seasonality at higher latitude in Neotropical South America becomes an important factor. PMID:27681478

Changes in Species Richness and Composition of Tiger Moths (Lepidoptera: Erebidae: Arctiinae among Three Neotropical Ecoregions.

Directory of Open Access Journals (Sweden)

Hernán Mario Beccacece

Full Text Available Paraná, Yungas and Chaco Serrano ecoregions are among the most species-rich terrestrial habitats at higher latitude. However, the information for tiger moths, one of the most speciose groups of moths, is unknown in these ecoregions. In this study, we assess their species richness and composition in all three of these ecoregions. Also we investigated whether the species composition of tiger moths is influenced by climatic factors and altitude. Tiger moth species were obtained with samples from 71 sites using standardized protocols (21 sites were in Yungas, 19 in Paraná and 31 in Chaco Serrano. Rarefaction-extrapolation curves, non-parametric estimators for incidence and sample coverage indices were performed to assess species richness in the ecoregions studied. Non metric multidimensional scaling and adonis tests were performed to compare the species composition of tiger moths among ecoregions. Permutest analysis and Pearson correlation were used to evaluate the relationship among species composition and annual mean temperature, annual temperature range, annual precipitation, precipitation seasonality and altitude. Among ecoregions Paraná was the richest with 125 species, followed by Yungas with 63 species and Chaco Serrano with 24 species. Species composition differed among these ecoregions, although Yungas and Chaco Serrano were more similar than Paraná. Species composition was significantly influenced by climatic factors and altitude. This study showed that species richness and species composition of tiger moths differed among the three ecoregions assessed. Furthermore, not only climatic factors and altitude influence the species composition of tiger moths among ecoregions, but also climatic seasonality at higher latitude in Neotropical South America becomes an important factor.

Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

Energy Technology Data Exchange (ETDEWEB)

Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

2014-08-01

A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

Characterisation and concentration profile of aluminium during ...

African Journals Online (AJOL)

An aluminium(Al) characterisation study was conducted at a surface water treatment plant (Buffalo Pound Water Treatment Plant (BPWTP) in Moose Jaw, Saskatchewan, Canada) to understand better the effect of alum coagulant on various Al fractions. The raw water source for BPWTP is Buffalo Pound Lake water. The Al ...

Feet sunk in molten aluminium: The burn and its prevention.

Science.gov (United States)

Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

2015-08-01

Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

The activation of aluminium by mercury ions in non-aggressive media

Energy Technology Data Exchange (ETDEWEB)

Bessone, J.B. [INIEC-Dto de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)]. E-mail: jbessone@criba.edu.ar

2006-12-15

The presence of Hg at concentration less than 300 ppm in Al base alloys causes their passivation breakdown. On alloys used as sacrificial anodes, it causes a major lowering (>0.3 V) in their operational potential in chloride media. Mercury as trace constituent in the natural gas stream causes severe damage to cryogenic heat exchangers. The present paper presents evidences of the mechanism by which mercury produces its pronounced effect in aqueous non-aggressive media. The work was carried out using pure (99.99%) aluminium and mercury (II) acetate solutions of different concentrations and pH. Open circuit potential-time responses were obtained. The surface effects were followed by means of scanning microscopy and EDAX/X-Ray analysis. The results demonstrate that immediately after immersion, the initial air-formed oxide film underwent a dynamic crack-healing process at flaws in the film, possible associated to grain boundaries. The subsequent healing process, if any, depends on the media composition. Thus, in this special case, Hg{sup 2+} ions can be directly reduced on the bare aluminium, reaching a true metallic contact, and initiating surface diffusion. This enables the formation of an amalgam. Aluminium atoms diffuse through the liquid mercury and undergo oxidation at the amalgam/electrolyte interface. This process is responsible for the oxide detachment (by undermining) and the attack morphology (i.e., wide cavities). The presence of aggressive anions is not needed to initiate activation.

Circular economy: To be or not to be in a closed product loop? A Life Cycle Assessment of aluminium cans with inclusion of alloying elements

DEFF Research Database (Denmark)

Niero, Monia; Olsen, Stig Irving

2016-01-01

Packaging, representing the second largest source of aluminium scrap at global level, deserves a key role in the transition towards the circular economy. Life Cycle Assessment (LCA) of aluminium products has been typically based on one life cycle considering pure aluminium flows and neglecting...... the presence of alloying elements and impurities. However, this simplification undermines the potentials of using LCA to quantify the environmental performances of products in multiple loops, as required in the circular economy. This study aims to investigate the effects of including the actual alloy...... composition in the LCA of aluminium can production and recycling, in order to understand whether a can-to-can (i.e. closed product loop) recycling should be promoted or not. Mass balance of the main alloying elements (Mn, Si, Cu, Fe) was carried out at increasing levels of recycling rate, corresponding...

Cold forming of aluminium - State of the art

DEFF Research Database (Denmark)

Bay, Niels

1997-01-01

The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable...... to that of unalloyed steel. After description of the different types of alloys and their individual properties and applications, the special requirements for tool design by cold forging in aluminium is discussed. Finally, a large number of industrial examples on cold forged aluminium components are presented. (C) 1997...

Effect of pressurized steam on AA1050 aluminium

DEFF Research Database (Denmark)

Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

2012-01-01

Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

Characterization of aluminium alloys rapidly solidified

International Nuclear Information System (INIS)

Monteiro, W.A.

1988-01-01

This paper discussed the investigation of the microstructural and mechanical properties of the aluminium alloys (3003; 7050; Al-9% Mg) rapidly solidified by melt spinning process (cooling rate 10 4 - 10 6 K/s). The rapidly solidification process of the studied aluminium alloys brought a microcrystallinity, a minimum presence of coarse precipitation and, also, better mechanical properties of them comparing to the same alloys using ingot process. (author) [pt

Low temperature oxidation of niobium alloy with silicon-aluminium coating

International Nuclear Information System (INIS)

Lazarev, Eh.M.; Sapozhnikova, L.V.; Shabanova, M.E.; Pod'yachev, V.N.; Kornilova, Z.I.

1987-01-01

Using the gravimetry methods heat resistance of niobium-titanium-aluminium alloy in the air and at 700 deg C in the initial state and when it is protected by silicide-aluminium coatings (with variable content of aluminium) is investigated. Using X-ray diffraction and micro X-ray diffraction analyses, mechanisms of the alloy oxidation and the coating protective effect are studied. The role of aluminium in the formation of coatings is analyzed and according to bend tests the plasticity of the coatings is evaluated

The structure of high-quality aluminium cast iron

Directory of Open Access Journals (Sweden)

D. Kopyciński

2012-01-01

Full Text Available In this study presents the analyse of aluminium iron cast structure (as-cast condition which are used in high temperature. While producing the casts of aluminium iron major influence has been preserve the structure of technological process parameters. The addition to Fe-C-Al alloy V, Ti, Cr leads to the improvement of functional and mechanical cast qualities. In this study, a method was investigated to eliminate the presence of undesirable Al4C3 phases in a aluminium cast iron structure and thus improve the production process. V and Ti additions in aluminium cast iron allows to development of FeAl - VC or TiC alloys. In particular, V or Ti contents above 5 wt.% were found to totally eliminate the presence of Al4C3. In addition, preliminary work indicates that the alloy with the FeAl - VC or TiC structure reveals high oxidation resistance. The introduction of 5 wt.% chromium to aluminium cast iron strengthened Al4C3 precipitate. Thus, the resultant alloy can be considered an intermetallic FeAl matrix strengthened by VC and TiC or modified Al4C3 reinforcements.

Intraspecific aluminium response in Suillus luteus (L. s.f. gray., an ectomycorrhizal symbiont of scots pine

Directory of Open Access Journals (Sweden)

Tomasz Leski

2014-01-01

Full Text Available Ten isolates of the ectomycorrhizal fungus Suillus luteus have been cultured on an aluminium containing growth medium in order to determine their in vitro aluminium tolerance. Five isolates originated from a site heavily polluted by acid rain with a high availability of aluminium in the soil. Five others were collected from a site free from direct pollution. Aluminium content in the sporocarps of S. luteus differed according to the site of origin and did not reveal symptoms of bioconcentration, although such phenomena were found when mycelium isolated from the sporocarps was submited to 100 mg/L Al in liquid culture. A clear relationship between Al accumulation in vitro and the site of origin of the isolate was not observed, although the highest amount of Al was found in the mycelium derived from the polluted soil. In a second experiment all isolates were grown in agar media containing 10, 100, 500 and 1000 mg/L-1 Al and the colony diameter during culture and the final colony dry weight determined. S. luteus appeared to be very tolerant to the presence of Al in the medium. Each of the parameters used to measure the metal tolerance of the fungus ranked the isolates in a slightly different order, but those originating from the polluted area showed some superiority over the others. In polluted soils this species seems to have been submitted to a selection for higher aluminium tolerance. The results are discussed with reference to the possibilities of transformating in vitro studies to situation in the forest ecosystem.

An Investigation on Tensile Properties of Glass Fiber/Aluminium Laminates

Directory of Open Access Journals (Sweden)

M. Sadighi

2009-12-01

Full Text Available The idea of combining low weight and good mechanical properties has led to efforts to develop a new light fiber/metal laminate (FML in the last decade. FMLs are hybrid composites consisting of alternating thin layers of metal sheets and fiber-reinforced epoxy prepregs. In this study, the effect of fiber orientation on tensile properties of this material is investigated both analytically and experimentally. An analytical constitutive model based on classical lamination theory by using Kirchhoff-Love assumption, which incorporates the elastic-plastic behavior of the aluminium alloy was applied. Test results show that fiber sheet, with zero angle in laminates, improve the tensile strength. The composite layers with different fiber orientation change specimens' mode of fracture. Good agreement is obtained between the model predictions and experimental results.

Method of preparing an Al-Ti-B grain refiner for aluminium-comprising products, and a method of casting aluminium products

NARCIS (Netherlands)

Brinkman, H.J.; Duszczyk, J.; Katgerman, L.

1999-01-01

The invention relates to a method of preparing an Al-Ti-B grain refiner for cast aluminium-comprising products. According to the invention the preparation is realized by mixing powders selected from the group comprising aluminium, titanium, boron, and alloys and intermetallic compounds thereof,

Grasshopper species composition shifts following a severe rangeland grasshopper outbreak

Science.gov (United States)

Little is known about how grasshopper species abundances shift during and following severe outbreaks, as sampling efforts usually end when outbreaks subside. Grasshopper densities, species composition and vegetation have infrequently been sampled during and after a severe outbreak in the western U.S...

Factors affecting the species composition of arable field boundary vegetation

NARCIS (Netherlands)

Kleijn, D.; Verbeek, M.

2000-01-01

1. In recent decades the botanical diversity of arable field boundaries has declined drastically. To determine the most important factors related to the species composition of arable field boundaries, the vegetation composition of 105 herbaceous boundaries, 1-m wide, in the central and eastern

Influence of aluminium incorporation on the structure of ZrN films deposited at low temperatures

Energy Technology Data Exchange (ETDEWEB)

Araiza, J J [Unidad Academica de Fisica, Universidad Autonoma de Zacatecas, Paseo a la Bufa esq, Calzada Solidaridad s/n 98060, Zacatecas (Mexico); Sanchez, O [Departamento de Fisica e Ingenieria de Superficies, Instituto de Ciencia de Materiales de Madrid-CSIC, C/ Sor Juana Ines de la Cruz 3, 28049 Cantoblanco, Madrid (Spain)], E-mail: olgas@icmm.csic.es

2009-06-07

We have studied the influence of Al incorporation in the crystalline structure of ZrN thin films deposited by dc magnetron sputtering at low temperature. The amount of aluminium in the films depends directly on the power applied to the aluminium cathode during the deposition. Energy dispersive x-ray analysis and x-ray diffraction (XRD) were used to obtain the chemical composition and crystalline structure of the films, respectively. When Al atoms are incorporated into the ZrN coatings, the strong ZrN (2 0 0) orientation is modified by a combination of other ones such as ZrN (1 1 1), Zr{sub 3}N{sub 4} (2 1 1) and hexagonal AlN (1 0 0) as detected from the XRD spectra for high aluminium concentrations. Fourier-transform infrared spectroscopy allowed us to identify oxides and nitrides, ZrO, AlO and AlN, incorporated into the deposited films. The effect of a bias voltage applied to the substrate has also been investigated and related to the changes in the microstructure and in the nanohardness values of the ZrAlN films.

Recovery of tritium from lithium-sintered aluminium product (SAP) and lithium-aluminium alloys

International Nuclear Information System (INIS)

Talbot, J.B.; Wiffen, F.W.

1979-01-01

The tritium release rates of irradiated samples of lithium-containing aluminium (Li-Al) and sintered aluminium product (Li-SAP) were investigated to evaluate the potential application of both materials in fusion reactors. The observed release rates followed the pattern expected for bulk diffusion of tritium in a solid. Therefore, diffusion coefficients for tritium in Li-SAP were determined over a temperature range of 383 and 500 0 C and tritium in Li-Al at 450 0 C. At 450 0 C, the diffusion coefficients of tritium in Li-SAP and Li-Al are 2.988 x 10 -10 cm 2 sec -1 and 1.462 x 10 -6 cm 2 sec -1 , respectively. (author)

VARIATION OF MACROMYCETES SPECIES COMPOSITION IN TWO FOREST HABITATS FROM GIUMALĂU MASSIF (EASTERN CARPATHIANS, ROMANIA

Directory of Open Access Journals (Sweden)

BÎRSAN Ciprian

2013-12-01

Full Text Available Norway spruce (Picea abies is the most common species with a large spreading in forests from Giumalău Massif. In this study the authors investigated the macromycetes species composition in two forest communities from Giumalău Massif: Hieracio transsilvanico-Piceetum and Leucanthemo waldsteinii-Fagetum. A total of 243 macromycetes species in 30 sampling areas have been identified. Changes in macromycetes species composition have been related to environmental factors (altitude and vegetation (canopy cover, plant species diversity. The results suggest that variation in macromycetes species composition in the two forests types from Giumalău Massif is directly related to abiotic factors (altitude, woody species composition and plants communities’ structure.

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived ...

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Abstract. Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form γ-Al2O3 at ~ 400°C but the formation of α-Al2O3 at 1200°C occurs more readily in the material ...

Influence of Alkali Treatment on the Surface Area of Aluminium Dross

Directory of Open Access Journals (Sweden)

N. S. Ahmad Zauzi

2016-01-01

Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

Facile synthesis of aluminium doped zinc oxide-polyaniline hybrids for photoluminescence and enhanced visible-light assisted photo-degradation of organic contaminants

Energy Technology Data Exchange (ETDEWEB)

Mitra, Mousumi [Department of Physics, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103, West Bengal (India); Ghosh, Amrita; Mondal, Anup [Department of Chemistry, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103, West Bengal (India); Kargupta, Kajari [Department of Chemical Engineering, Jadavpur University, Kolkata 700032, West Bengal (India); Ganguly, Saibal [Department of Chemical Engineering, BITS Pilani, K K Birla Goa Campus, NH 17 B Bypass Road, Zuarinagar, Sancoale, Goa 403726 (India); Banerjee, Dipali, E-mail: dipalibanerjeebesu@gmail.com [Department of Physics, Indian Institute of Engineering Science and Technology, Shibpur, Howrah 711103, West Bengal (India)

2017-04-30

Graphical abstract: The present work focuses on the synergistic effect of a novel hybrid hetero structure (n-type aluminum doped zinc oxide and p-type polyaniline), combining both sol-gel and in-situ oxidative polymerization method and studying its photoluminescence (PL), photocatalytic, electrochemical impedance spectroscopy (EIS), linear scan voltammetry (LSV) and photocurrent properties. - Highlights: • Aluminium doped zinc oxide-polyaniline (PAZ) hybrids were prepared by polymerization of aniline using aluminium doped zinc oxide nanorod templates. • The hybrids were used as visible light photocatalysts for methyl orange (MO) and rose bengal (RB) dye degradation. • First order rate constants of the photocatalytic process were evaluated as 1.77 × 10{sup −2} min{sup −1} and 2.61 × 10{sup −2} min{sup −1} for MO and RB dyes respectively. • Photoluminescence and electrochemical properties were in accord with the photocatalytic performance of the hybrid. - Abstract: The emergence of organic-inorganic photoactive materials has led to marked progress in the field of heterogeneous visible-light photocatalysis. Visible-light active aluminium doped zinc oxide-polyaniline (PAZ) hybrid was prepared employing in-situ oxidative polymerization of polyaniline (PANI) in the presence of aluminium doped zinc oxide (AlZnO) nanorods, synthesized via sol-gel route. The compositions, structural and optical properties of the synthesized hybrids were characterized. Among various samples, the 22 wt% aluminium doped zinc oxide-polyaniline (PAZ 3) hybrid show the best photocatalytic action for the degradation of methyl orange (MO) and rose bengal (RB) dyes under visible-light illumination, even after repeated use. The performance of the photocatalytic process was determined by the first order rate constant, 1.77 × 10{sup −2} min{sup −1} and 2.61 × 10{sup −2} min{sup −1} for MO and RB dyes, respectively. Scavenger test was used to determine the role of active

Chemical composition of hydroethanolic extracts from five species of the Passiflora genus

Directory of Open Access Journals (Sweden)

Marna E Sakalem

2012-09-01

Full Text Available The diversified genus Passiflora is well distributed all over Brazil, and many species have been long used as medicinal plants, mainly against anxiety disturbances. This effect has been attributed to its rich flavonoid composition. Flavonoids’ main class, flavonoid glycosides, has presented central action, particularly as sedative-hypnotic, anxiolytic and analgesic. The objective of the present study was to make a phytochemical screening of five little studied Passiflora species, in order to evaluate their phenolic composition. For this aim, HPLC-DAD-ESI-MS/MS was used. After the preparation of the hydroalcoholic extracts, each species was evaluated by direct injection electrospray ionization (ESI and tandem mass spectrometry. Although belonging to the same genus, the composition of each species presented particularities; this justifies the importance of studies aiming for the phenolic composition of different Passiflora species. Flavones C-glycosides were detected in all extracts, and are found as the main constituents in P. vitifolia, P. coccinea, P. bahiensis and P. sidifolia. In this last one, flavone-6,8-di-C-glycoside, apigenin-6-C-rhamnosyl-8-C-arabinoside are present in high content. Cyclopassiflosides were found in high content together with cyanogenic glycosides in P. quadrangularis, while in P. coccinea, besides flavones-C-glycosides were also found procyanidins.

Chemical composition of hydroethanolic extracts from five species of the Passiflora genus

Directory of Open Access Journals (Sweden)

Marna E Sakalem

2012-12-01

Full Text Available The diversified genus Passiflora is well distributed all over Brazil, and many species have been long used as medicinal plants, mainly against anxiety disturbances. This effect has been attributed to its rich flavonoid composition. Flavonoids’ main class, flavonoid glycosides, has presented central action, particularly as sedative-hypnotic, anxiolytic and analgesic. The objective of the present study was to make a phytochemical screening of five little studied Passiflora species, in order to evaluate their phenolic composition. For this aim, HPLC-DAD-ESI-MS/MS was used. After the preparation of the hydroalcoholic extracts, each species was evaluated by direct injection electrospray ionization (ESI and tandem mass spectrometry. Although belonging to the same genus, the composition of each species presented particularities; this justifies the importance of studies aiming for the phenolic composition of different Passiflora species. Flavones C-glycosides were detected in all extracts, and are found as the main constituents in P. vitifolia, P. coccinea, P. bahiensis and P. sidifolia. In this last one, flavone-6,8-di-C-glycoside, apigenin-6-C-rhamnosyl-8-C-arabinoside are present in high content. Cyclopassiflosides were found in high content together with cyanogenic glycosides in P. quadrangularis, while in P. coccinea, besides flavones-C-glycosides were also found procyanidins.

Sinter aluminium as cladding material for fuel elements

International Nuclear Information System (INIS)

Mann, K.E.; Boudouresques, M.B.

1961-01-01

1. Survey of the production process of sinter aluminium. 2. Description of the forming processes (extrusion, forging and rolling), whereby the production of tubing for atom piles will be explained in detail. 3. Production of ribbed tubes and tubes with close tolerances of sizes. 4. The different SAP-qualities and their properties under special consideration of the properties at elevated temperatures and the creep properties. 5. Diffusion behaviour of SAP with Be, Mg, Al, U and UO 2 . 6. Corrosion behaviour in CO 2 atmosphere at high temperature and in water. 7. Weldability. 8. Effect of irradiation on the mechanical properties. 9. Superiority of SAP compared with normal wrought alloys of the same composition. (author) [fr

The binding, transport and fate of aluminium in biological cells.

Science.gov (United States)

Exley, Christopher; Mold, Matthew J

2015-04-01

Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion. Copyright © 2014 Elsevier GmbH. All rights reserved.

Magnetic field dependence observed by 27 Al NMR of species contained in alumina colloidal dispersions

International Nuclear Information System (INIS)

Morgado Junior, Edisson; Menezes, Sonia M.C.; San Gil, Rosane

1995-01-01

The behaviour of some aluminium species front a magnetic field have been investigated by 27 Al NMR analysis, this method was used for characterization of an octahedric aluminium specie from sols prepared by bohemite acid peptization. X-ray diffraction data have identified the mineral structure. The results have been shown and discussed, and NMR spectra were also presented and studied. Concluding this work, the nature of a colloidal specie of alumina was clarified through the dependence research of magnetic field by 27 Al NMR

Aluminium and Aroma Compound Concentration in Beer During Storage at Different Temperatures

Directory of Open Access Journals (Sweden)

Marija Soldo Gjeldum

2006-01-01

Full Text Available Problem of aluminium in beer has been elaborated in several papers over the last decade. However, the effect of aluminium on organoleptic properties of beer has been observed in few papers where it has been stated that aluminium gives beer a »metallic« and bitter flavour without any observations on particular aroma compound changes. Also, the number of reports on precise changes of aroma components throughout different storage conditions is surprisingly scarce. In order to investigate the changes of aluminium concentration along with aroma compound changes, graphite furnace-atomic absorption spectrophotometry (GF-AAS with Zeeman background correction and gas chromatography with static headspace sampler (GC-HSS were used in this work. Analyses were conducted periodically throughout seven months of storage on three different brands of beer from name breweries. Samples were taken before and after filling in aluminium cans. One part of samples was stored in a refrigerator (4 °C and the other in a thermostatic chamber (22 °C. The effects of beer brand and storage conditions on aluminium concentration and level of aroma compounds were measured. To prove the effect of aluminium concentration on the changes of aroma compounds, the adequate level of aluminium sulphate was added to bottled beer samples stored at 28 °C. Although different beer types showed significantly different aluminium concentration, it could be the result of other factors (different batches of identical beer type showed significantly different aluminium concentration as well. Samples that were stored in the refrigerator were protected from aluminium migration from the can to the beer and showed increased aroma stability. Level of aroma constituents of analyzed beer brands was significantly different. Elevated aluminium concentration did not have any noticeable effect on the level of aroma compounds in beer samples stored at 28 °C.

Affinity of hydroxyapatite to metal cations. A study on the composition and structure of phosphates formed in the presence of titanium and aluminium

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, C.C. [Instituto de Eng. Biomedica, Porto (Portugal). Lab. de Biomateriais; Porto Univ. (Portugal). Faculdade de Engenharia; Inst. Superior de Engenharia, Porto (Portugal); Barbosa, M.A. [Instituto de Eng. Biomedica, Porto (Portugal). Lab. de Biomateriais; Porto Univ. (Portugal). Faculdade de Engenharia

2001-07-01

The purpose of this study was to contribute to the understanding of the effect of titanium, aluminium and titanium/aluminium on the Hap structure and to investigate if a synergistic effect between the two cations exists. The effect of the metal ion concentration was studied. The solids were analysed by X-ray diffraction, Fourier transform infrared spectroscopy, FT-Raman spectroscopy and energy dispersive X-ray analysis. (orig.)

Sintered aluminium powders

International Nuclear Information System (INIS)

Stepanova, M.G.; Matveev, B.I.

1974-01-01

The mechanical and physical properties of aluminium powder alloys and the various methods employed to produce them are considered. Data are given on the hardening of the alloys SAP and SPAK-4, as well as the powder-alloy system Al-Cr-Zr. (L.M.)

Silane based coating of aluminium mold

DEFF Research Database (Denmark)

2013-01-01

having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...... of structures which would otherwise be difficult to mold. The resistance of the coated aluminium mold is significantly improved by applying a silane-based coating layer....

Aluminium hydroxide-induced granulomas in pigs

DEFF Research Database (Denmark)

Valtulini, S; Macchi, C; Ballanti, P

2005-01-01

The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

Finite size melting of spherical solid-liquid aluminium interfaces

DEFF Research Database (Denmark)

Chang, J.; Johnson, Erik; Sakai, T.

2009-01-01

We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting tempera...... to the conclusion that the depressed melting temperature is not controlled solely by the inverse radius 1/R. Instead, we found a direct relation between the depressed melting temperature and the ratio between the solid-liquid interface area and the molten volume.......We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting...

Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

NARCIS (Netherlands)

Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

2012-01-01

Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide

Drilling of metal matrix composites: cutting forces and chip formation

International Nuclear Information System (INIS)

Songmene, V.; Balout, B.; Masounave, J.

2002-01-01

Particulate metal matrix composites (MMCs) are known for their low weight and their high wear resistance, but also for the difficulties encountered during their machining. New aluminium MMCs containing with both soft lubricating graphite particles and hard particles (silicon carbide or alumina) with improved machinability were developed. This study investigates the drilling of these composites as compared to non-reinforced aluminium. The microstructure of chip, the cutting forces, the shear angles and the friction at tool-chip interface are used to compare the machinability of these composites. It was found that, during drilling of this new family of composites, the feed rate, and the nature of reinforcing particles govern the cutting forces. The mathematical models established by previous researchers for predicting the cutting forces when drilling metals were validated for these composites. The reinforcing particles within the composite help for chip segmentation, making the composite more brittle and easy to shear during the cutting process. (author)

Disruption of an Alumina Layer During Sintering of Aluminium in Nitrogen

Directory of Open Access Journals (Sweden)

Pieczonka T.

2017-06-01

Full Text Available Aluminium oxide layer on aluminium particles cannot be avoided. However, to make the metal-metal contacts possible, this sintering barrier has to be overcome in some way, necessarily to form sintering necks and their development. It is postulated that the disruption of alumina layer under sintering conditions may originate physically and chemically. Additionally, to sinter successfully non alloyed aluminium powder in nitrogen, the operation of both types mechanism is required. It is to be noted that metallic aluminium surface has to be available to initiate reactions between aluminium and the sintering atmosphere, i.e. mechanical disruption of alumina film precedes the chemical reactions, and only then chemically induced mechanisms may develop. Dilatometry, gravimetric and differential thermal analyses, and microstructure investigations were used to study the sintering response of aluminium at 620°C in nitrogen, which is the only sintering atmosphere producing shrinkage.

Feasibility study on development of metal matrix composite by microwave stir casting

Science.gov (United States)

Lingappa, S. M.; Srinath, M. S.; Amarendra, H. J.

2018-04-01

Need for better service oriented materials has boosted the demand for metal matrix composite materials, which can be developed to have necessary properties. One of the most widely utilized metal matrix composite is Al-SiC, which is having a matrix made of aluminium metal and SiC as reinforcement. Lightweight and conductivity of aluminium, when combined with hardness and wear resistance of SiC provides an excellent platform for various applications in the field of electronics, automotives, and aerospace and so on. However, uniform distribution of reinforcement particles is an issue and has to be addressed. The present study is an attempt made to develop Al-SiC metal matrix composite by melting base metal using microwave hybrid heating technique, followed by addition of reinforcement and stirring the mixture for obtaining homogenous mixture. X-Ray Diffraction analysis shows the presence of aluminium and SiC in the cast material. Further, microstructural study shows the distribution of SiC particles in the grain boundaries.

Species Composition, Relative Abundance and Distribution of the ...

African Journals Online (AJOL)

Species Composition, Relative Abundance and Distribution of the Avian Fauna of Entoto Natural Park and Escarpment, Addis Ababa. ... Eucalyptus plantation, soil erosion, deforestation, habitat fragmentation, settlement and land degradation were the main threats for the distribution of birds in the present study area.

Tribological Behaviour of W-DLC against an Aluminium Alloy Subjected to Lubricated Sliding

Directory of Open Access Journals (Sweden)

S. Bhowmick

2015-09-01

Full Text Available Diamond like carbon (DLC coatings mitigate aluminium adhesion and reduce friction under the ambient conditions but their tribological behaviour under lubricated sliding need to be further investigated. In this study, tribological tests were performed to evaluate the friction and wear characteristics of W-DLC and H-DLC coatings sliding against an aluminium alloy (319 Al under unlubricated (40 % RH and lubricated sliding conditions. For unlubricated sliding, coefficient of friction (COF values of H-DLC and W-DLC were 0.15 and 0.20. A lower COF value of 0.11 was observed when W-DLC was tested using lubricant oil incorporating sulphur while the H-DLC’s COF remained almost unchanged. The mechanisms responsible for the low friction of W-DLC observed during lubricated sliding were revealed by studying the compositions of the coating surfaces and the transfer layers formed on 319 Al. Micro-Raman spectroscopy indicated that the transfer layers formed during lubricated sliding of W-DLC incorporated tungsten disulphide (WS2.

Surface roughness when diamond turning RSA 905 optical aluminium

Science.gov (United States)

Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

2015-08-01

Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

Near infra-red spectroscopy quantitative modelling of bivalve protein, lipid and glycogen composition using single-species versus multi-species calibration and validation sets

Science.gov (United States)

Bartlett, Jill K.; Maher, William A.; Purss, Matthew B. J.

2018-03-01

Near infrared spectroscopy (NIRS) quantitative modelling was used to measure the protein, lipid and glycogen composition of five marine bivalve species (Saccostrea glomerata, Ostrea angasi, Crassostrea gigas, Mytilus galloprovincialis and Anadara trapezia) from multiple locations and seasons. Predictive models were produced for each component using individual species and aggregated sample populations for the three oyster species (S. glomerata, O. angasi and C. gigas) and for all five bivalve species. Whole animal tissues were freeze dried, ground to > 20 μm and scanned by NIRS. Protein, lipid and glycogen composition were determined by traditional chemical analyses and calibration models developed to allow rapid NIRS-measurement of these components in the five bivalve species. Calibration modelling was performed using wavelet selection, genetic algorithms and partial least squares analysis. Model quality was assessed using RPIQ and RMESP. For protein composition, single species model results had RPIQ values between 2.4 and 3.5 and RMSEP between 8.6 and 18%, the three oyster model had an RPIQ of 2.6 and an RMSEP of 10.8% and the five bivalve species had an RPIQ of 3.6 and RMSEP of 8.7% respectively. For lipid composition, single species models achieved RPIQ values between 2.9 and 5.3 with RMSEP between 9.1 and 11.2%, the oyster model had an RPIQ of 3.6 and RMSEP of 6.8 and the five bivalve model had an RPIQ of 5.2 and RMSEP of 6.8% respectively. For glycogen composition, the single species models had RPIQs between 3.8 and 18.9 with RMSEP between 3.5 and 9.2%, the oyster model had an RPIQ of 5.5 and RMSEP of 7.1% and the five bivalve model had an RPIQ of 4 and RMSEP of 7.6% respectively. Comparison between individual species models and aggregated models for three oyster species and five bivalve species for each component indicate that aggregating data from like species produces high quality models with robust and reliable quantitative application. The benefit of

In vivo monitoring of skeletal aluminium burden in patients with renal failure

International Nuclear Information System (INIS)

Ellis, K.J.; Kelleher, S.; Raciti, A.; Savory, J.; Wills, M.

1988-01-01

In vivo neutron activation analysis was used to examine the total body and partial body (hand) aluminium levels in patients with end-stage renal failure. Patients maintained on chronic hemodialysis had higher mean body burdens of aluminium than did those clinically managed without dialysis. Approximately 70% of the patients examined indicated elevated levels of body or skeletal aluminium. A significant correlation was observed between the in vivo aluminium/calcium ratio obtained for the hand measurement and the increase in serum aluminium levels following a disferroxamine infusion test. The direct in vivo monitoring of hand Al/Ca values in patients may provide an alternate choice to bone biopsy for the detection of aluminium intoxication. (author) 15 refs.; 5 figs.; 2 tabs

Dietary exposure to aluminium in the popular Chinese fried bread youtiao.

Science.gov (United States)

Li, Ge; Zhao, Xue; Wu, Shimin; Hua, Hongying; Wang, Qiang; Zhang, Zhiheng

2017-06-01

Youtiao is a typical, traditional and widely consumed fried food in China. Fermentation of youtiao involves the use of aluminium potassium sulphate (alum). There are health concerns related to the levels of aluminium in food; therefore, we aimed to determine the aluminium concentrations of youtiao from various locations, and to estimate the dietary exposure by different age groups in southern and northern China. The aluminium content of youtiao samples varied considerably (range = 4.46-852.69 mg kg -1 ). Both the mean and median aluminium contents of youtiao exceeded 100 mg kg -1 , which is the China National Standard (GB) 2760-2014 National Food Safety for Standards for food additives. However, the median and 97.5th percentile of weekly dietary exposure to aluminium from youtiao, estimated using Monte Carlo simulation, did not exceed the provisional tolerable weekly intake (PTWI) set by the joint FAO/WHO Expert Committee on Food Additives (JECFA) for children, adolescents, adults and seniors. The weekly dietary exposure to aluminium would exceed the PTWI if children, adolescents, adults and seniors consumed 134.47, 260.98, 327.10 or 320.41 g of youtiao per week, respectively.

Dietary exposure to aluminium of urban residents from cities in South China.

Science.gov (United States)

Jiang, Qi; Wang, Jing; Li, Min; Liang, Xuxia; Dai, Guangwei; Hu, Zhikun; Wen, Jian; Huang, Qiong; Zhang, Yonghui

2013-01-01

A dietary survey was conducted over three consecutive days by using 24-hour dietary recall in the Pearl River Delta of South China to investigate the dietary consumption status. A total of 1702 food samples, 22 food groups, were collected, and aluminium concentrations of foods were determined by using ICP-MS. Weekly dietary exposure to aluminium of the average urban residents of South China was estimated to be 1.5 mg kg⁻¹ body weight, which amounted to 76% of the provisional tolerable weekly intake. Wheat-made products (53.5%) contributed most to the dietary exposure, followed by vegetables (12.2%). The high-level consumers' weekly exposure to aluminium was 11.1 mg kg⁻¹ body weight, which amounted to 407% of the provisional tolerable weekly intake. The results indicated that the general urban residents in South China might be safe from aluminium exposure, but the high-level consumers might be at some risk of aluminium exposure. The foods contributing to aluminium exposure were processed food with aluminium-containing food additives. It is necessary to take effective measures to control the overuse of aluminium-containing food additives.

Aluminium matrix heterophase composites for air compressor pistons

Directory of Open Access Journals (Sweden)

M.Dyzia

2011-04-01

Full Text Available The article presents the results of surface test of composite shaped in the permanent mould casting process. As part of the research anddevelopment project realized in the Department of Materials Technology at the Silesian University of Technology, a pilot plant scale stand was built to manufacture of more than 50 kg suspensions in a single technological cycle. Made in industrial conditions castings to form in the five inner core mould mounted in GM110 permanent mould casting machine confirmed the possibility of the shaping the composite pistons. Castings made from composite suspension AlSi7Mg/SiC and AlSi7Mg/SiC + Cg according to the technology procedure were classified as correct and devoted to the proper machining forming working surfaces of the piston to the air compressor. Comparative tests were performed for the casting of unreinforced AlSi7Mg alloy and composite castings. To assess the ability to fill the mold cavity and the accuracy of mapping used in contour shape FRT analysis of the distance between the grooves on the surface of the piston skirt. Studies have confirmed the differences in the fluidity of alloy matrix and composites suspensions. The difference in the accuracy of the dimensional mapping mould does not disqualify of composite materials, all castings are classified as correct and used for machining.

The aluminium content of breast tissue taken from women with breast cancer.

Science.gov (United States)

House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

2013-10-01

The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

Preparation of magnesium metal matrix composites by powder metallurgy process

Science.gov (United States)

Satish, J.; Satish, K. G., Dr.

2018-02-01

Magnesium is the lightest metal used as the source for constructional alloys. Today Magnesium based metal matrix composites are widely used in aerospace, structural, oceanic and automobile applications for its light weight, low density(two thirds that of aluminium), good high temperature mechanical properties and good to excellent corrosion resistance. The reason of designing metal matrix composite is to put in the attractive attributes of metals and ceramics to the base metal. In this study magnesium metal matrix hybrid composite are developed by reinforcing pure magnesium with silicon carbide (SiC) and aluminium oxide by method of powder metallurgy. This method is less expensive and very efficient. The Hardness test was performed on the specimens prepared by powder metallurgy method. The results revealed that the micro hardness of composites was increased with the addition of silicon carbide and alumina particles in magnesium metal matrix composites.

APPLICATION OF CHEMICAL PRE-TREATMENT ON THE POLISHED SURFACE OF ALUMINIUM ALLOYS

Directory of Open Access Journals (Sweden)

Pavel Kraus

2016-12-01

Full Text Available This paper reports the preparation and characterization of thin transparent nanolayers with phase composition ZrF4 and different modification of SiO2 with special focus on affecting the surface roughness of the material and the way of exclusion of the thin nanolayer on the surface of the polished aluminium material. The thin nanolayer was prepared by the sol-gel method. The final treatment based on PTFE was applied on the surface of some samples. This treatment is suitable for increasing wear resistance. The films were characterized with help of SEM microscopy and EDS analysis. The surface roughness was measured with classical surface roughness tester. The results on this theme have already published but not on the polished surface of the aluminium material. The results from the experiment show the problems with application of these nanolayers because a cracks were found on the surface of the material and deformations of the layer after application of the PTFE final layer. The surface layer formation is discussed.

Microstructural characterization of fly ash particulate reinforced AA6063 aluminium alloy for aerospace applications

Science.gov (United States)

Razzaq, A. M.; Majid, D. L. Abang Abdul; Ishak, M. R.; Uday, M. B.

2017-12-01

Aluminium-fly ash (FA) particulate reinforced composites (AA6063-FA) have been used in automotive and aerospace industries because of their low density and good mechanical properties. Three different weight fraction of FA: 2%, 4% and 6% are added to AA6063 alloy using compocasting method. The effect of FA particulates on microstructure, density and compression strength of AA6063- FA composites are investigated. Field Emission Scanning Electron Microscope (FESEM) micrographs reveal that the FA particulates are uniformly distributed in AA6063 alloy. The results also show that density, compression strength and microstructure of the AA6063-FA composites are significantly influenced by the FA amount. The increase in the weight fraction of FA will improve the microstructure and enhance the compression strength. The density of AA6063-FA composites decreases as the incorporation of FA increases.

Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

Directory of Open Access Journals (Sweden)

Senze Magdalena

2015-03-01

Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

Lake restoration with aluminium, bentonite and Phoslock: the effect on sediment stability and light attenuation

DEFF Research Database (Denmark)

Egemose, Sara; Reitzel, Kasper; Flindt, Mogens

treatments on aluminium mobility, sediment stability or light climate. A laboratory flume experiment including three shallow Danish lakes was conducted. We measured the effects of aluminium, Phoslock (a commercial product), bentonite, and a combination of bentonite/aluminium. Each treatment caused a varying...... consolidation of the sediment. The largest consolidation occurred using Phoslock- and bentonite-addition followed by bentonite/aluminium-addition, whereas aluminium alone had no effect. Sediment stability thresholds were measured before and after addition. Especially Phoslock, but also bentonite and bentonite....../aluminium increased sediment erosion threshold, with respectively 200%, 43% and 57%. Aluminium, bentonite/aluminium, and Phoslock improved the light conditions in the water phase, with respectively 60%, 57% and 50%, whereas bentonite created higher turbidity. Conclusively aluminium improved the light conditions...

Anodization of Aluminium using a fast two-step process

Indian Academy of Sciences (India)

283.6 eV. Keywords. Anodization; phosphoric acid; anodization time; anodized aluminium oxide; aluminium. ... of anodization.5–7 The AAO layer has a large band gap, good ..... transmittance increases as the anodised membrane is heated to ...

Serum aluminium levels in glue-sniffer adolescent and in glue containers.

Science.gov (United States)

Akay, Cemal; Kalman, Süleyman; Dündaröz, Ruşen; Sayal, Ahmet; Aydin, Ahmet; Ozkan, Yalçin; Gül, Hüsamettin

2008-05-01

Glue sniffing is a serious medical problem among teenagers. Various chemical substances such as toluene and benzene containing glues have been reported to be toxic. It has been demonstrated that some toxic metals such as lead are elevated in the blood of solvent-addicted patients. Whereas aluminium is an element that has toxic effects on neurological, hematopoetic system and bone metabolism. We want to determine the serum levels of aluminium in glue-sniffer adolescents in comparison with healthy subjects. In addition, we compared aluminium levels of different commercial glue preparations (i.e. metal and plastic containers), to determine which type of container is better for less aluminium toxicity. We measured serum levels of aluminium in 37 glue-sniffer and 37 healthy subjects using atomic absorption spectrophotometry. The average duration of glue-sniffer was 3.8 +/- 0.8 years. We also measured aluminium levels of 10 commercial glue preparations that seven of them with metal and three with plastic containers. We found that serum levels of aluminium were 63.29 +/- 13.20 ng/ml and 36.7 +/- 8.60 ng/ml in glue-sniffer and in control subjects, respectively (P sniffers, it may be a good step to market of glue preparations in plastic instead of metal containers.

Cancer risk among workers of a secondary aluminium smelter.

Science.gov (United States)

Maltseva, A; Serra, C; Kogevinas, M

2016-07-01

Cancer risk in secondary aluminium production is not well described. Workers in this industry are exposed to potentially carcinogenic agents from secondary smelters that reprocess aluminium scrap. To evaluate cancer risk in workers in a secondary aluminium plant in Spain. Retrospective cohort study of male workers employed at an aluminium secondary smelter (1960-92). Exposure histories and vital status through 2011 were obtained through personal interviews and hospital records, respectively. Standardized mortality (SMRs) and incidence ratios (SIRs) were calculated. The study group consisted of 98 workers. We found increased incidence and mortality from bladder cancer [SIR = 2.85, 95% confidence interval (CI) 1.23-5.62; SMR = 5.90, 95% CI 1.58-15.11]. Increased incidence was also observed for prostate cancer and all other cancers but neither were statistically significant. No increased risk was observed for lung cancer. Results of this study suggest that work at secondary aluminium smelters is associated with bladder cancer risk. Identification of occupational carcinogens in this industry is needed. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Property enhancement by grain refinement of zinc-aluminium foundry alloys

International Nuclear Information System (INIS)

Krajewski, W K; Piwowarski, G; Krajewski, P K; Greer, A L

2016-01-01

Development of cast alloys with good mechanical properties and involving less energy consumption during their melting is one of the key demands of today's industry. Zinc foundry alloys of high and medium Al content, i.e. Zn-(15-30) wt.% Al and Zn-(8-12) wt.% Al, can satisfy these requirements. The present paper summarizes the work [1-9] on improving properties of sand-cast ZnAl10 (Zn-10 wt.% Al) and ZnAl25 (Zn-25 wt. % Al) alloys by melt inoculation. Special attention was devoted to improving ductility, whilst preserving high damping properties at the same time. The composition and structural modification of medium- and high-aluminium zinc alloys influence their strength, tribological properties and structural stability. In a series of studies, Zn - (10-12) wt. % Al and Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The melted alloys were inoculated with ZnTi-based refiners and it was observed that the dendritic structure is significantly finer already after addition of 50 - 100 ppm Ti to the melted alloys. The alloy's structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), dilatometry, pin-on-disc wear, and tensile strength measurements. Grain refinement leads to significant improvement of ductility in the binary high-aluminium Zn-(25-27) Al alloys while in the medium-aluminium alloys the effect is rather weak. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties. Furthermore, the high initial damping properties were nearly entirely preserved after inoculation. The results obtained allow us to characterize grain refinement of the examined high-aluminium zinc alloys as a promising process leading to the improvement of their properties. At the same time, using low melting ZnTi-based master alloys makes it possible to avoid the excessive melt

Deposition of aluminium nanoparticles using dense plasma focus device

International Nuclear Information System (INIS)

Devi, Naorem Bilasini; Srivastava, M P; Roy, Savita

2010-01-01

Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

Corrosion issues of powder coated AA6060 aluminium profiles

DEFF Research Database (Denmark)

Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl

2015-01-01

In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

Floristic composition, environmental variation and species distribution patterns in burned grassland in southern Brazil.

Science.gov (United States)

Overbeck, G E; Müller, S C; Pillar, V D; Pfadenhauer, J

2006-11-01

In regularly burned grassland on Morro Santana, Porto Alegre, RS, Brazil, we investigated differences in the floristic composition and their relation to soil properties, aspect and distance from the forest border. In 48 plots of 0.75 m2, we identified a total of 201 species from a local species pool of approximately 450 to 500 species. Most species occurred in low frequencies, showing clumpy distribution patterns in the studied area. Multivariate analysis showed that plots close to the forest edge clearly differed from plots in the open grassland concerning composition and structure. Plots exposed to the north differed from plots on the top of the hill both in the composition of species as well as in soil variables, mainly due to shallower soil in the former. No strong relation between soil properties and variation in vegetation composition could be detected at a finer scale. The studied grassland, as all grassland vegetation in southern Brazil, is very rich in species compared to other grassland formations worldwide. However, this high biodiversity and conservational value of Campos vegetation in general has so far not been recognized properly. Disturbance is essential to maintain this open vegetation type and its species richness. Fire should be considered as a management option in the absence of grazing.

Synthesis and investigation of aluminium uranium-containing compounds of Al[B5UO6]2[OH]·nH2O (B5=P, As) composition

International Nuclear Information System (INIS)

Chernorukov, N.G.; Sulejmanov, E.V.; Barch, S.V.

2001-01-01

The technique of synthesis of hydroxyuranophosphate and hydroxyuranoarsenate of aluminium is developed. Hydroxyuranophosphates and hydroxyuranoarsenates of aluminium are prepared by reaction of interaction of aqueous solutions of orthophosphoric (orthoarsenic) acid (0.05 mol/l), uranyl nitrate (0.05 mol/l) and aluminium nitrate (0.1 mol/l) at 20 Deg C. Peculiarities of the structure and thermal degradation reactions are studied by the methods of x-ray diffraction, IR spectroscopy, thermography. It is shown that in dependence on outer conditions in the systems Al[PUO 6 ] 2 ·[OH]·nH 2 O and Al[AsUO 6 ] 2 ·[OH]·nH 2 O crystal hydrates with hydrate numbers n=3-11(13) and anhydrous compounds form. The compounds have laminated type of lattice. Two-dimensional layers of [P(As)UO 6 ] ∞ n- are the basis of anion sublattice of these compounds. Aluminium in coordination surrounding of hydroxy groups and water molecules forms cationic sublattice [ru

SPECIES COMPOSITION OF PSAMMOPHILIC CILIATES OF SUMGAIT CASPIAN COAST

Directory of Open Access Journals (Sweden)

I. Kh. Alekperov

2014-01-01

Full Text Available Abstract. Comparative data on the species composition and species saprobic indicators of the psammon ciliates from Sumgait coast of the Caspian Sea are given.Methods. “Alive” samples were collected using a small clean plastic wide mouth bottles. Further processing was carried out under laboratory conditions. Small quantities of soil were examined under a binocular microscope MBS-9 . Ciliates detected microvessel caught and fixed castors for further impregnation kinetoma silver nitrate (Chatton et Lwoff, 1930 or silver proteinate. To determine the keys for ciliates used Foyssner’s major publications (Foissner et al., 1991, 1992, 1999 and “Free-living ciliates Atlas” (Alekperov, 2005.Results. We observed 75 species of ciliates during the studies, which species composition and distribution of the collection points are shown in table 1. Diagrams with average data were made relations groups psammophilous ciliates indicators saprobity different zones for each of the sites investigated Sumgait coast.Main conclusions. Environmental analysis using benthic ciliates indicators saprobity different zones showed that as expected, the industrial zone of Sumgayit coast coast, despite the decline in recent years, the total amount of pollution that is still highly contaminated portion of the coastal zone of the Caspian Sea.

Aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference.

Science.gov (United States)

Zhao, Xue Qiang; Guo, Shi Wei; Shinmachi, Fumie; Sunairi, Michio; Noguchi, Akira; Hasegawa, Isao; Shen, Ren Fang

2013-01-01

Acidic soils are dominated chemically by more ammonium and more available, so more potentially toxic, aluminium compared with neutral to calcareous soils, which are characterized by more nitrate and less available, so less toxic, aluminium. However, it is not known whether aluminium tolerance and nitrogen source preference are linked in plants. This question was investigated by comparing the responses of 30 rice (Oryza sativa) varieties (15 subsp. japonica cultivars and 15 subsp. indica cultivars) to aluminium, various ammonium/nitrate ratios and their combinations under acidic solution conditions. indica rice plants were generally found to be aluminium-sensitive and nitrate-preferring, while japonica cultivars were aluminium-tolerant and relatively ammonium-preferring. Aluminium tolerance of different rice varieties was significantly negatively correlated with their nitrate preference. Furthermore, aluminium enhanced ammonium-fed rice growth but inhibited nitrate-fed rice growth. The results suggest that aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference under acidic solution conditions. A schematic diagram summarizing the interactions of aluminium and nitrogen in soil-plant ecosystems is presented and provides a new basis for the integrated management of acidic soils.

Fabrication, microstructural characterization and wear characteristics of A380 alloy-alumina composites

KAUST Repository

Nurani, Sheikh Jaber

2016-03-10

To obtain better mechanical and tribological properties than aluminium alloys aluminium is reinforced with alumina particles making aluminium metal matrix composites. In this work scrap piston A380 alloy was used as the matrix alloy. Alumina particles were added by 5%, 10% and 15% into matrix alloy respectively to form desired composites by stir casting technique. Pin on disc wear testing machine with counter surface as steel disc of hardness HRC 32 and surface roughness of 0.62 μm was used to conduct the wear test. In result composites showed superior wear resistance property over A380 alloy. The effect of load, sliding speed and sliding distance on wear behaviour were also examined in this study. Wear mechanism was identified from the worn surface. Both optical and scanning electron microscope (SEM) of the composites was performed to determine the microstructures. Optical micrograph shows grain size decreases with addition of alumina particles. EDS analysis was performed to confirm the presence of α-Al matrix, primary Si particles and intermetallic. As a general method, phase compositions were analyzed by using a scanning electron microscope (SEM) equipped with an energy dispersive spectroscopy (EDS). Optical microstructures were consistent with the SEM micrographs. © 2015 IEEE.

Species composition of insects in contaminated areas of Apsheron

International Nuclear Information System (INIS)

Guseynzadeh, G.A; Mamedova, T.G; Atakishiyeva, A.M; Hajiyeva, S.A

2010-01-01

Full text:The main area of the Apsheron Peninsula, semi-complete urbanization area, where as a result of human impact, in particular oil production and processing large areas of once fertile land have been ruined. As a result, formed locally contaminated sites where the oil soaks into the soil to a depth of 1m or more, the mold is completely ruined. The aim of our research was to study the species composition of bugs, beetles, butterflies, bees in these locally contaminated areas of Absheron, their relationships and nutritive degree of occurrence. Expeditionary trips were made in the following areas: Karadag, Seaside, Bibi Geybatsky, Surakhani, Sabunchu Oil Gas Mining Management, Ramaninsky iodine plant. These areas are divided into three gradations of anthropogenic strain:1) The weak degree of load-zone relatively clean; 2) The average degree of load-space of moderate economic use; A strong degree of load-immediately adjacent to the locally-contaminated sites. According to the results of environmental monitoring of terrestrial invertebrates group found: bugs, 22 species, 10 species of beetles, butterflies, eight species of bee-25, found food and the degree of occurrence of communication. Identified several types of bee-bioindicators: Zholletes similes, Schylaeus variegate, Andrew Flavipes. Identification of these species will provide an opportunity to determine in advance the impact of background radiation in this ecosystem and to conduct cleaning, remediation work. On the basis of faunal material collected in Table 1 shows the species composition of the above insects, food relations and the degree of occurrence.

Indentation of aluminium foam at low velocity

Directory of Open Access Journals (Sweden)

Shi Xiaopeng

2015-01-01

Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

Improvement of photodynamic activity of aluminium sulphophthalocyanine due to biotinylation

Science.gov (United States)

Meerovich, Irina G.; Jerdeva, Victoria V.; Derkacheva, Valentina M.; Meerovich, Gennadii A.; Lukyanets, Eugeny A.; Kogan, Eugenia A.; Savitsky, Alexander P.

2003-09-01

The photodynamic activity of dibiotinylated aluminium sulphophthalocyanine in vitro and in vivo were studied. It was obtained that in vitro dibiotinylated aluminium sulphophthalocyanine provides the effective damage of small cell lung carcinoma OAT-75. In vivo dibiotinylated aluminium sulphophthalocyanine causes destruction of tumor (Erlich carcinoma), results in total necrosis of tumor tissue and expresses vascular damage (trombosis and destruction of vascular walls) even in concentration 0.25 mg/kg of a body weight.

Aluminium supplier selection for the automotive parts manufacturer

Directory of Open Access Journals (Sweden)

M. Cieśla

2016-04-01

Full Text Available This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method and a graphical method. Choosing the best offer and prioritizing suppliers allows not only the most rational decision in the field of supply logistics to be taken but also the quality of service in the metallurgical industry to be improved.

Ultrasonic studies of aluminium-substituted Bi(Pb)-2223 superconductors

Science.gov (United States)

Solunke, M. B.; Sharma, P. U.; Pandya, M. P.; Lakhani, V. K.; Modi, K. B.; Venugopal Reddy, P.; Shah, S. S.

2005-09-01

The compositional dependence of elastic properties of Al^{3+}-substitu- ted Bi(Pb)-2223 superconducting system with the general formula Bi_{1.7-x}Al_xPb_{0.3}Sr_2Ca_2- Cu_3O_y (x = 0.0, 0.1, 0.2 and 0.3) have been studied by means of ultrasonic pulse transmission (UPT) technique at 1 MHz (300 K). The elastic moduli of the specimens are computed and corrected to zero porosity. The observed variation of elastic constants with aluminium substitution has been explained on the basis of the strength of interatomic bonding. The applicability of heterogeneous metal mixture rule for estimating elastic constants and transition temperature has been tested.

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Science.gov (United States)

Mudge, David W; Johnson, David W; Hawley, Carmel M; Campbell, Scott B; Isbel, Nicole M; van Eps, Carolyn L; Petrie, James J B

2011-05-13

Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing concerns about the risks of

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Directory of Open Access Journals (Sweden)

van Eps Carolyn L

2011-05-01

Full Text Available Abstract Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer, which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Science.gov (United States)

2011-01-01

Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing

An interesting and efficient green corrosion inhibitor for aluminium ...

African Journals Online (AJOL)

An interesting and efficient green corrosion inhibitor for aluminium from extracts of ... Journal Home > Vol 13, No 1 (2014) > ... possible applications in metal surface anodizing and surface coating in industries. Keywords: Moringa oleifera, Aluminium, Hydrochloric acid, Langmuir isotherm, Plant extracts, Corrosion inhibition ...

Power distribution: conductors in aluminium

International Nuclear Information System (INIS)

Schmid, R.

2007-01-01

This article takes a look at the use of aluminium conductors in medium and low-voltage cables. The author discusses how the increasing price of copper has led to the increasing use of aluminium as a material for the production of the conductors used in medium and low-voltage power cables. Aid is provided that is to help purchasers make the correct decisions when buying medium and low-voltage cables. The current market situation is examined and the appropriate norms are looked at. Technical data and economic aspects are discussed, both for medium and low-voltage applications. The electrical characteristics of the type of cable to be used are examined and discussed

The influence of alloy composition on residual stresses in heat treated aluminium alloys

Energy Technology Data Exchange (ETDEWEB)

Robinson, J.S., E-mail: jeremy.robinson@ul.ie [Department of Mechanical, Aeronautical and Biomedical Engineering, University of Limerick (Ireland); Redington, W. [Materials and Surface Science Institute, University of Limerick (Ireland)

2015-07-15

The as quenched properties of eight different heat treatable aluminium alloys are related to residual stress magnitudes with the objective being to establish if there is a relationship between the residual stress and the as quenched alloy hardness and strength. Near surface residual stresses were assessed with X-ray diffraction using both the established sin{sup 2}ψ method and the more recent cos α technique. Through thickness residual stresses were also characterised using neutron diffraction. The alloys were chosen to encompass a wide range of strengths. The low to medium strength alloys were 6060 and 6082, medium to high strength 2618A, 2014A, 7075, 7010 and two variants of 7449, while the very high strength alloy was the powder metallurgy alloy N707. To assess the as quenched strength, dynamic hardness and tensile properties were determined from samples tested immediately after quenching to minimise the influence of precipitation hardening by natural aging. In addition, hot hardness measurements were made in situ on samples cooled to simulate quench paths. Within the experimental constraints of the investigation, the distribution of residual stress through the thickness was found to follow the same pattern for all the alloys investigated, varying from tensile in the interior to surface compression. The influence of alloy strength was manifested as a change in the observed residual stress magnitudes, and surface residual stresses were found to vary linearly with as quenched hardness and strength. - Highlights: • As quenched aluminium alloys contain high magnitude residual stresses. • Surface is compressive balance by a tensile core. • As quenched surface residual stress is linear function of alloy strength. • In situ hot hardness demonstrates rapid change in intrinsic hardness during rapid cooling.

Spectrographic determination of trace impurities in reactor grade aluminium

International Nuclear Information System (INIS)

Chandola, L.C.; Machado, I.J.

1975-01-01

A spectrographic method enabling the determination of 21 trace impurities in aluminium oxide is described. The technique involves mixing the sample with graphite buffer in the ratio 1:1, loading it in a graphite electrode and arcing it for 30 sec. in a dc arc to 10 A current against a pointed graphite cathode. The spectra are photographed on Ilford N.30 emulsion employing a large quartz spectrograph. The aluminium line at 2669.2 A 0 serves as the internal standard. The impurities determined are Ag, B, Bi, Cd, Co, Cr, Cu, Fe, Ga, In, Mg, Mo, Ni, Pb, Sb, Si, Sn, Ti, V and Zn. The sensitivity varies from 5 to 100 ppm and the precision from +- 5 to +- 22% for different elements. A method for converting aluminium metal to aluminium oxide is described. It is found that boron is not lost during this conversion. (author)

Towards toxicokinetic modelling of aluminium exposure from adjuvants in medicinal products.

Science.gov (United States)

Weisser, Karin; Stübler, Sabine; Matheis, Walter; Huisinga, Wilhelm

2017-08-01

As a potentially toxic agent on nervous system and bone, the safety of aluminium exposure from adjuvants in vaccines and subcutaneous immune therapy (SCIT) products has to be continuously re-evaluated, especially regarding concomitant administrations. For this purpose, knowledge on absorption and disposition of aluminium in plasma and tissues is essential. Pharmacokinetic data after vaccination in humans, however, are not available, and for methodological and ethical reasons difficult to obtain. To overcome these limitations, we discuss the possibility of an in vitro-in silico approach combining a toxicokinetic model for aluminium disposition with biorelevant kinetic absorption parameters from adjuvants. We critically review available kinetic aluminium-26 data for model building and, on the basis of a reparameterized toxicokinetic model (Nolte et al., 2001), we identify main modelling gaps. The potential of in vitro dissolution experiments for the prediction of intramuscular absorption kinetics of aluminium after vaccination is explored. It becomes apparent that there is need for detailed in vitro dissolution and in vivo absorption data to establish an in vitro-in vivo correlation (IVIVC) for aluminium adjuvants. We conclude that a combination of new experimental data and further refinement of the Nolte model has the potential to fill a gap in aluminium risk assessment. Copyright © 2017 Elsevier Inc. All rights reserved.

RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

Science.gov (United States)

Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

2015-01-01

Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

Modelling of heterogeneous clustering in aluminium

International Nuclear Information System (INIS)

Smith, A.E.; Bourgeois, L.; Nie, J.-F.; Muddle, B.C.

2003-01-01

Full text: Ab initio modelling of heterogeneous clustering in aluminium has been carried out in order to study the precipitation hardening of alloys. This process is based on the addition of small amounts of solute element to the pure metal. With increasing computational power, atomic scale effects can now be better simulated to determine the nature of the hardening mechanism. Comparisons are made between results obtained from two computational packages. These are the Linear Augmented Plane Wave WEEN2K and the plane wave pseudopotential density functional theory package fhi98md. The study of the optimal geometry of very small size clusters inside aluminium has begun with the testing of initial convergence conditions by determination of binding energies for a variety of super cell sizes of the aluminium host crystal. These are compared with total energy calculations for small size precipitates of copper and transition metals of fixed geometry. Such local optimal determinations are seen as precursors to full Monte Carlo calculations of the notional best local geometry for larger precipitates

Synthesis of aluminium nanoparticles by arc evaporation of an ...

Indian Academy of Sciences (India)

Administrator

Abstract. Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on.

Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance

CSIR Research Space (South Africa)

Nath, S

2012-03-01

Full Text Available Department of Metallurgical & Materials Engineering, IIT Kharagpur, West Bengal, India 2National Laser Centre, CSIR, Pretoria, South Africa Abstract In the present study, laser surface alloying of aluminium with WC+Co+NiCr (in the ratio of 70... be used for dispersion of ceramic materials into metallic matrix and hence, form a ceramic dispersed metal matrix composite on metallic substrate [3]. The advantages of laser surface alloying include refinement of the microstructure, uniform dispersion...

Determining sample size for assessing species composition in ...

African Journals Online (AJOL)

Species composition is measured in grasslands for a variety of reasons. Commonly, observations are made using the wheel-point apparatus, but the problem of determining optimum sample size has not yet been satisfactorily resolved. In this study the wheel-point apparatus was used to record 2 000 observations in each of ...

Tensile behavior of dissimilar friction stir welded joints of aluminium alloys

International Nuclear Information System (INIS)

Shanmuga Sundaram, N.; Murugan, N.

2010-01-01

The heat treatable aluminium alloy AA2024 is used extensively in the aircraft industry because of its high strength to weight ratio and good ductility. The non-heat treatable aluminium alloy AA5083 possesses medium strength and high ductility and used typically in structural applications, marine, and automotive industries. When compared to fusion welding processes, friction stir welding (FSW) process is an emerging solid state joining process which is best suitable for joining these alloys. The friction stir welding parameters such as tool pin profile, tool rotational speed, welding speed, and tool axial force influence the mechanical properties of the FS welded joints significantly. Dissimilar FS welded joints are fabricated using five different tool pin profiles. Central composite design with four parameters, five levels, and 31 runs is used to conduct the experiments and response surface method (RSM) is employed to develop the model. Mathematical regression models are developed to predict the ultimate tensile strength (UTS) and tensile elongation (TE) of the dissimilar friction stir welded joints of aluminium alloys 2024-T6 and 5083-H321, and they are validated. The effects of the above process parameters and tool pin profile on tensile strength and tensile elongation of dissimilar friction stir welded joints are analysed in detail. Joints fabricated using Tapered Hexagon tool pin profile have the highest tensile strength and tensile elongation, whereas the Straight Cylinder tool pin profile have the lowest tensile strength and tensile elongation. The results are useful to have a better understanding of the effects of process parameters, to fabricate the joints with desired tensile properties, and to automate the FS welding process.

Premature thermal fatigue failure of aluminium injection dies with duplex surface treatment

International Nuclear Information System (INIS)

Corujeira Gallo, S.; Figueroa, Carlos A.; Baumvol, Israel J.R.

2010-01-01

Research highlights: → The premature failure of an aluminium injection die with a duplex surface treatment (plasma nitriding and physical vapor deposition coating) was investigated. → The origin of failure was attributed to the sulfur inclusions introduced into the surface of the tool by a sulfur-impregnated grinding stone used in the final polishing operation. → The low adhesion of the CrN coating on the sulfur inclusions led to the spalling of the coating, the exposure of the substrate material and the nucleation of cracks. → New evidence is presented on the influence of surface preparation and manufacturing processes on aluminium injection tool performance. - Abstract: The premature failure of an aluminium injection die with a duplex surface treatment (plasma nitriding and physical vapor deposition coating) was investigated, in an effort to identify the causes of such premature failure of the component. The manufacturing and the operating conditions were documented. Analytical tools were used, including scanning electron microscopy with energy dispersive X-ray capability, X-ray diffraction, and instrumented microhardness testing. Preliminary observations showed a microstructure of coarse tempered martensite, and a considerably rough surface with porosity and cracks. A detailed analysis of crack initiation sites identified sulfur inclusions in the subsurface, underneath the coating. A further revision of the processing conditions revealed that a sulfur-impregnated grinding stone had been used to polish the die. The chemical composition of such grinding stone matched that of the inclusions found in the subsurface of the failed component. Thus, searched causes of premature failure could be discussed on the lights of the present findings.

Light-weight aluminium bridges and bridge decks. An overview of recent applications

NARCIS (Netherlands)

Maljaars, J.; Soetens, F.; Kluyver, D. de

2008-01-01

The last decades have shown a large increase in the application of aluminium alloys for light-weight bridges. For bridge construction, aluminium alloys have some specific advantages, but also some points of attention. This paper deals with some recent projects of aluminium bridges, and for these

Improving the wettability of 2024 aluminium alloy by means of cold plasma treatment

Science.gov (United States)

Polini, W.; Sorrentino, L.

2003-05-01

Aluminium alloys are heavily used to manufacture structural parts in the aeronautic industry because of its lightness and its corrosion resistance. These alloys are successfully used in other industrial fields too, such as railway, automotive and naval industries. The need to contrast the severe use conditions and the heavy stresses developing in aeronautic field implies to protect the surfaces of the structures in aluminium alloy by any deterioration. To preserve by deterioration, it is necessary to make aluminium more suitable to be coated by protective paint. In the aeronautic industry, a complex and critical process is used in order to enhance both wettability and adhesive properties of aluminium alloy surfaces. Cold plasma treatment represents an efficient, clean and economic alternative to activate aluminium surfaces. The present work deals with air cold plasma treatment of 2024 aluminium alloy surfaces. The influence of dc electrical discharge cold plasma parameters on wettability of 2024 aluminium alloy surfaces has been studied. A set of process variables (voltage, time and air flow rate) has been identified and used to conduct some experimental tests on the basis of design of experiment (DOE) techniques. The experimental results show that the proposed plasma process may considerably increase aluminium alloy wettability. These results represent the first step in trying to optimise the aluminium adhesion by means of this non-conventional manufacturing process.

Dinucleotide Composition in Animal RNA Viruses Is Shaped More by Virus Family than by Host Species.

Science.gov (United States)

Di Giallonardo, Francesca; Schlub, Timothy E; Shi, Mang; Holmes, Edward C

2017-04-15

Viruses use the cellular machinery of their hosts for replication. It has therefore been proposed that the nucleotide and dinucleotide compositions of viruses should match those of their host species. If this is upheld, it may then be possible to use dinucleotide composition to predict the true host species of viruses sampled in metagenomic surveys. However, it is also clear that different taxonomic groups of viruses tend to have distinctive patterns of dinucleotide composition that may be independent of host species. To determine the relative strength of the effect of host versus virus family in shaping dinucleotide composition, we performed a comparative analysis of 20 RNA virus families from 15 host groupings, spanning two animal phyla and more than 900 virus species. In particular, we determined the odds ratios for the 16 possible dinucleotides and performed a discriminant analysis to evaluate the capability of virus dinucleotide composition to predict the correct virus family or host taxon from which it was isolated. Notably, while 81% of the data analyzed here were predicted to the correct virus family, only 62% of these data were predicted to their correct subphylum/class host and a mere 32% to their correct mammalian order. Similarly, dinucleotide composition has a weak predictive power for different hosts within individual virus families. We therefore conclude that dinucleotide composition is generally uniform within a virus family but less well reflects that of its host species. This has obvious implications for attempts to accurately predict host species from virus genome sequences alone. IMPORTANCE Determining the processes that shape virus genomes is central to understanding virus evolution and emergence. One question of particular importance is why nucleotide and dinucleotide frequencies differ so markedly between viruses. In particular, it is currently unclear whether host species or virus family has the biggest impact on dinucleotide frequencies and

Effect of iron and silicon in aluminium and its alloys

International Nuclear Information System (INIS)

Kovacs, I.

1990-01-01

The iron and silicon are the main impurities in aluminium, they are always present in alloys made from commercially pure base material. The solid solubility of iron in aluminium is very low, therefore its largest amount forms intermetallic compounds the kind of which depends strongly on the other impurities of alloying elements. Although the solid solubility of silicon is much larger than that of the iron, it is the constituent of both the primary and the secondary particles, the structure of which depends in general on the iron-silicon concentration ratio. These Fe and Si containing particles can cause various and basic changes in the macroscopic properties of the alloy. Since commercially pure aluminium has extensive consumer and industrial use, it is very important to know, not only from scientific but also from practical point of view, the effect of iron and silicon on the physical and mechanical properties of aluminium and its alloys. The aim of the ''International Workshop on the Effect of Iron and Silicon in Aluminium and its Alloys'' was to clarify the present knowledge on this subject. The thirty papers presented at the Workshop and collected in this Proceedings cover many important fields of the subject. I hope that they will contribute to both the deeper understanding of the related phenomena and the improvement of technologies for producing better aluminium alloys

Species effects on ecosystem processes are modified by faunal responses to habitat composition.

Science.gov (United States)

Bulling, Mark T; Solan, Martin; Dyson, Kirstie E; Hernandez-Milian, Gema; Luque, Patricia; Pierce, Graham J; Raffaelli, Dave; Paterson, David M; White, Piran C L

2008-12-01

Heterogeneity is a well-recognized feature of natural environments, and the spatial distribution and movement of individual species is primarily driven by resource requirements. In laboratory experiments designed to explore how different species drive ecosystem processes, such as nutrient release, habitat heterogeneity is often seen as something which must be rigorously controlled for. Most small experimental systems are therefore spatially homogeneous, and the link between environmental heterogeneity and its effects on the redistribution of individuals and species, and on ecosystem processes, has not been fully explored. In this paper, we used a mesocosm system to investigate the relationship between habitat composition, species movement and sediment nutrient release for each of four functionally contrasting species of marine benthic invertebrate macrofauna. For each species, various habitat configurations were generated by selectively enriching patches of sediment with macroalgae, a natural source of spatial variability in intertidal mudflats. We found that the direction and extent of faunal movement between patches differs with species identity, density and habitat composition. Combinations of these factors lead to concomitant changes in nutrient release, such that habitat composition effects are modified by species identity (in the case of NH4-N) and by species density (in the case of PO4-P). It is clear that failure to accommodate natural patterns of spatial heterogeneity in such studies may result in an incomplete understanding of system behaviour. This will be particularly important for future experiments designed to explore the effects of species richness on ecosystem processes, where the complex interactions reported here for single species may be compounded when species are brought together in multi-species combinations.

Combining projected changes in species richness and composition reveals climate change impacts on coastal Mediterranean fish assemblages

DEFF Research Database (Denmark)

Albouy, Camille; Guilhaumon, François; Bastos Araujo, Miguel

2012-01-01

future climatic niches of 288 coastal Mediterranean fish species based on a global warming scenario. We then aggregated geographically the species-level projections to analyse the projected changes in species richness and composition. Our results show that projected changes in assemblage composition....... nestedness), separately. We also present a mapping strategy to simultaneously visualize changes in species richness and assemblage composition. To illustrate our approach, we used the Mediterranean coastal fish fauna as a case study. Using Bioclimatic Envelope Models (BEMs) we first projected the potential......, the joint exploration of changes in species richness and composition coupled with the distinction between species replacement and nestedness bears important information for understanding the nature of climate change impacts on biodiversity. These methodological advances should help decision...

BOREAS TGB-3 Plant Species Composition Data over the NSA Fen

Science.gov (United States)

Bubier, Jill L.; Hall, Forrest G. (Editor); Conrad, Sara K. (Editor)

2000-01-01

The BOReal Ecosystem-Atmosphere Study Trace Gas Biogeochemistry (BOREAS TGB-3) team collected several data sets that contributed to understanding the measured trace gas fluxes over sites in the Northern Study Area (NSA). This data set contains information about the composition of plant species that were within the collars used to measure Net Ecosystem Exchange of CO2 (NEE). The species composition was identified to understand the differences in NEE among the various plant communities in the NSA fen. The data were collected in July of 1994 and 1996. The data are contained in comma-delimited, ASCII files.

Does mechanical disturbance affect the performance and species composition of submerged macrophyte communities?