WorldWideScience

Sample records for aluminium pressure die

  1. Application of laser additive manufacturing to produce dies for aluminium high pressure die casting

    CSIR Research Space (South Africa)

    Pereira, MFVT

    2012-07-01

    Full Text Available through immersion in liquid aluminium. The dipping cycle closely resembles the heating and cooling cycle of a typical aluminium die under casting conditions. The suitability of any LAM technology, that can produce fully dense metallic components... cost vs wrought manufactured 5.2 1,7 2. 2 Average cost Very High Medium High Table 3: Processing and finishing costs of test coupons 3.1 Cyclic Immersion in Molten Aluminium Figure 3 below shows the testing apparatus developed to simulate...

  2. Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

    Directory of Open Access Journals (Sweden)

    Iban Vicario

    2016-01-01

    Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

  3. Technical-economic modelling of an aluminium high pressure die casting system for automotive parts fabrication

    International Nuclear Information System (INIS)

    Faura, F.

    1997-01-01

    In the present paper a technical-economic model for an aluminium high pressure die casting system has been developed. In order to obtain the necessary data for correlations utilized by the model, has been analyzed the production systems of companies that use these processes. This has allowed to determine the most important technological variables that affect to the economical aspect of the process. A computer application has been developed which allows to explore easily the influence of different system parameters. (Author) 12 refs

  4. Comparative study on laser welding and TIG welding of semi-solid high pressure die cast A356 aluminium alloy

    CSIR Research Space (South Africa)

    Govender, G

    2007-07-01

    Full Text Available components. The low porosity levels in SSM high pressure die castings (HPDC) improves the weldability of these components. The aim of the current research was to perform a comparative study of laser and TIG welding of SSM HPDC aluminium alloy A356. SSM...

  5. Interlocking multi-material components made of structured steel sheets and high-pressure die cast aluminium

    Science.gov (United States)

    Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

    2017-10-01

    Lightweight design is a major driving force of innovation, especially in the automotive industry. Using hybrid components made of two or more different materials is one approach to reduce the vehicles weight and decrease fuel consumption. As a possible way to increase the stiffness of multi-material components, this paper presents a process chain to produce such components made of steel sheets and high-pressure die cast aluminium. Prior to the casting sequence the steel sheets are structured in a modified rolling process which enables continuous interlocking with the aluminium. Two structures manufactured by this rolling process are tested. The first one is a channel like structure and the second one is a channel like structure with undercuts. These undercuts enable the formation of small anchors when the molten aluminium fills them. The correlation between thickness reduction during rolling and the shape of the resulting structure was evaluated for both structures. It can be stated that channels with a depth of up to 0.5 mm and a width of 1 mm could be created. Undercuts with different size depending on the thickness reduction could be realised. Subsequent aluminium high-pressure die casting experiments were performed to determine if the surface structure can be filled gap-free with molten aluminium during the casting sequence and if a gap-free connection can be achieved after contraction of the aluminium. The casting experiments showed that both structures could be filled during the high-pressure die casting. The channel like structure results in a gap between steel and aluminium after contraction of the cast metal whereas the structure with undercuts leads to a good interlocking resulting in a gap-free connection.

  6. Inventory of pollution reduction options for an aluminium pressure die casting plant

    NARCIS (Netherlands)

    Neto, B.A.F.; Kroeze, C.; Hordijk, L.; Costa, C.

    2009-01-01

    This study presents an overview of options aiming to reduce emissions to air, soil and water from an aluminium die casting plant located in Portugal. We identify eighteen pollution reduction options and then estimate their potential to reduce the pollution, and the costs associated with their

  7. Strategies to reduce the environmental impact of an aluminium pressure die casting plant: A scenario analysis

    NARCIS (Netherlands)

    Neto, B.; Kroeze, C.; Hordijk, L.; Costa, C.; Pulles, M.P.J.

    2009-01-01

    This study explores a model (MIKADO) to analyse scenarios for the reduction of the environmental impact of an aluminium die casting plant. Our model calculates the potential to reduce emissions, and the costs associated with implementation of reduction options. In an earlier paper [Neto, B., Kroeze,

  8. Reducing non value adding aluminium alloy in production of parts through high pressure die casting

    CSIR Research Space (South Africa)

    Pereira, MFVT

    2010-10-01

    Full Text Available in the cast part feed system, including overflows. CSIR intends using the results of this research for further development and application of high temperature die construction materials in high pressure die casting processes of light metal alloys...

  9. The effect of natural pre-ageing on the mechanical properties of Rheo-High pressure die cast aluminium alloy 2139

    CSIR Research Space (South Africa)

    Chauke, L

    2015-07-01

    Full Text Available -high pressure die casting process (R-HPDC). Alloy 2139 is a Ag-containing aluminium alloy from the Al-Cu-Mg 2xxx series family. The addition of Ag enhances the age hardening response through the formation of co-clusters that act as precursors to the formation...

  10. Ejection Performance of Coated Core Pins Intended for Application on High Pressure Die Casting Tools for Aluminium Alloys Processing

    Directory of Open Access Journals (Sweden)

    P. Terek

    2017-09-01

    Full Text Available In high pressure die casting (HPDC process of aluminium alloys cast alloy soldering severely damages tool surfaces. It hampers casting ejection, reduces the casting quality and decreases the overall production efficiency. Thin ceramic PVD (physical vapor deposition coatings applied on tool surfaces successfully reduce these effects. However, their performance is still not recognised for surfaces with various topographies. In this investigation, soldering tendency of Al-Si-Cu alloy toward EN X27CrMoV51 steel, plasma nitrided steel, CrN and TiAlN duplex PVD coatings is evaluated using ejection test. The coatings were prepared to a range of surface roughness and topographies. After the tests sample surfaces were analysed by different microscopy techniques and profilometry. It was found that the ejection performance is independent of the chemical composition of investigated materials. After the ejection, the cast alloy soldering layer was found on surfaces of all tested materials. This built-up layer formed by effects of mechanical soldering, without corrosion reactions. Coated samples displayed a pronounced dependence of ejection force on surface roughness and topography. By decreasing roughness, ejection force increased, which is a consequence of intensified adhesion effects. Presented findings are a novel information important for efficient application of PVD coatings intendent for protection of HPDC tools.

  11. MIKADO: a decision support tool for pollution reduction in aluminium pressure die casting

    NARCIS (Netherlands)

    Neto, B.A.F.

    2007-01-01

    Industrial activities cause a variety of environmental problems. These are largely caused by emissions of air pollutants, the production of waste and depletion of natural resources. As a consequence, industrial managers face a complex problem when assessing the overall environmental pressure on the

  12. The ‘full sleeve’ application in the horizontal cold-chamber machine for pressure die casting of aluminium alloys

    Directory of Open Access Journals (Sweden)

    Z. Konopka

    2008-04-01

    Full Text Available The ‘full sleeve’ construction has been designed and accomplished in the horizontal cold-chamber pressure die casting machine. Main part of this solution is a counter plunger placed in a movable die half which allows for full filling of the shot sleeve and precisely fixes the metal quantity needed for casting. The purpose of this new construction solution is mainly the reduction of the casting porosity caused by air entrapment and the improvement of both castability and accuracy of the die cavity reproduction. For such a redesigned machine there have been performed examinations consisting in pressure casting of AlSi9Cu alloy (EN AC-46000 at varying plunger velocity in the second stage of injection and varying intensification pressure. The alloy castability (the die filling ability has been measured for each parameter setting. For the purpose of comparison, similar measurements have been performed also for the conventional system without a counter plunger. The castability examination has been done by means of a specially designed die with an impression of a trial casting of variable wall thickness. The experiments have been held according to the assumed factor design 22, what allowed for determining the mathematical models describing the influence of die filling parameters on the castability and the die cavity reproduction level. Both alternatives of the experiment confirmed the positive influence of plunger velocity and intensification pressure increase on the improvement of castability, the measure of the latter being the filled length of the impression. Applying of the new ‘full sleeve’ solution has improved castability for each experiment by about 20% as compared with conventional alternative. Castability in the ‘full sleeve’ system has been increased even for low values of plunger velocity and intensification pressure. For both alternative systems the influence of plunger velocity has been found, as an average, by four times

  13. Modelling of Filling, Microstructure Formation, Local Mechanical Properties and Stress – Strain Development in High-Pressure Die Cast Aluminium Castings

    DEFF Research Database (Denmark)

    Kotas, Petr; Hattel, Jesper Henri; Thorborg, Jesper

    2009-01-01

    .e. whether the casting is based on cast iron- or aluminium-alloys. The distribution of local properties in a casting might vary substantially which makes it complex to optimize the casting with good accuracy. Often, mechanical simulations of the load situation are based on the assumption that the cast...... in an aluminium alloy is considered including simulation of the entire casting process with emphasis on microstructure formation related to mechanical properties such as elastic modulus, yield stress, ultimate strength and elongation as well as residual stresses. Subsequently, the casting is subjected to service...... loads and the results of this analysis are discussed in relation to the predicted local properties as well as the residual stresses originating from the casting simulation....

  14. Helium behaviour in aluminium under hydrostatic pressure

    International Nuclear Information System (INIS)

    Sokurskij, Yu.N.; Tebus, V.N.; Zudilin, V.A.; Tumanova, G.M.

    1989-01-01

    Effect of hydrostatic compression on equilibrium helium bubbles in low aluminium-lithium alloy irradiated in reactor at 570 K is investigated. Measurements of hydrostatic density and electron-microscopic investigations have shown, that application of up to 2 GPa pressure reduces equilibrium size of helium bubbles and reduces helium swelling. Kinetics and thermodynamics of the process are considered with application of 'rigid sphere' equation which describes helium state in bubbles

  15. Effect of pressurized steam on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

    2012-01-01

    Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

  16. High-purity aluminium creep under high hydrostatic pressure

    International Nuclear Information System (INIS)

    Zajtsev, V.I.; Lyafer, E.I.; Tokij, V.V.

    1977-01-01

    The effect of the hydrostatic pressure on the rate of steady-state creep of high-purity aluminium was investigated. It is shown that the hydrostatic pressure inhibits the creep. The activation volume of the creep is independent of the direction in the range of (4.7-6.2) kg/mm 2 and of the pressure in the range of (1-7.8000) atm. It is concluded that self-diffusion does not control the creep of high-purity aluminium at room temperature in the investigated stress and pressure range

  17. Forging loads, deformation modes and fracture in axi-symmetrric closed die cold forging of sintered aluminium powder compacts

    International Nuclear Information System (INIS)

    Butt, M.A.; Ali, L.

    2003-01-01

    An experimental investigation into closed-die cold forging of sintered aluminium powder rod- shaped compacts was carried out. Axi-symmetric components were forged from sintered powder preforms with different initial diameter to height ratios. Different compaction pressures, sintering and lubrication conditions were used as variables during the investigations. Detailed observations were made on green/sintered density, compaction defects, forging loads, deformation modes and on the onset of fracture during progressive forging of sintered powder compacts. Experimental results obtained during the investigations have been presented and discussed in detail. (author)

  18. Pressurized air ionization chamber with aluminium walls for radiometric dosimetry

    International Nuclear Information System (INIS)

    Rodrigues, R.G.S.; Pela, C.A.; Netto, T.G.

    1996-01-01

    A pressurized air ionization chamber with 23 cm 3 and aluminium walls is evaluated concerning its sensitiveness in low exposure rate. Considering conventional ionization chambers, this chamber shows a better performance since the air pressure of 2500 kPa minimizes the energy dependence to less than 5% between 40 and 1.250 keV

  19. Energy and resource efficiency in aluminium die casting

    CERN Document Server

    Heinemann, Tim

    2016-01-01

    This monograph provides a field-proven approach to analyze industrial production with a cross-company scope as well as regarding all hierarchical system levels of manufacturing enterprises. The book exemplifies this approach in the context of aluminum  die casting, and presents a set of measures which allow a 30 percent energy reduction along the value chain. The target audience primarily comprises researchers and experts in the field but the book may also be beneficial for graduate students.

  20. Study the effect of elevated dies temperature on aluminium and steel round deep drawing

    International Nuclear Information System (INIS)

    Lean, Yeong Wei; Azuddin, M.

    2016-01-01

    Round deep drawing operation can only be realized by expensive multi-step production processes. To reduce the cost of processes while expecting an acceptable result, round deep drawing can be done at elevated temperature. There are 3 common problems which are fracture, wrinkling and earing of deep drawing a round cup. The main objective is to investigate the effect of dies temperature on aluminium and steel round deep drawing; with a sub-objective of eliminate fracture and reducing wrinkling effect. Experimental method is conducted with 3 different techniques on heating the die. The techniques are heating both upper and lower dies, heating only the upper dies, and heating only the lower dies. 4 different temperatures has been chosen throughout the experiment. The experimental result then will be compared with finite element analysis software. There is a positive result from steel material on heating both upper and lower dies, where the simulation result shows comparable as experimental result. Heating both upper and lower dies will be the best among 3 types of heating techniques. (paper)

  1. Pressing Speed, Specific Pressure and Mechanical Properties of Aluminium Cast

    Directory of Open Access Journals (Sweden)

    Gaspar S.

    2016-06-01

    Full Text Available Recent research in the process of aluminum alloy die castings production, which is nowadays deeply implemented into the rapidly growing automobile, shipping and aircraft industries, is aimed at increasing the useful qualitative properties of the die casting in order to obtain its high mechanical properties at acceptable economic cost. Problem of technological factors of high pressure die casting has been a subject of worldwide research (EU, US, Japan, etc.. The final performance properties of die castings are subjected to a large number of technological factors. The main technological factors of high pressure die casting are as follows: plunger pressing speed, specific (increase pressure, mold temperature as well as alloy temperature. The contribution discusses the impact of the plunger pressing speed and specific (increase pressure on the mechanical properties of the casting aluminum alloy.

  2. Premature thermal fatigue failure of aluminium injection dies with duplex surface treatment

    International Nuclear Information System (INIS)

    Corujeira Gallo, S.; Figueroa, Carlos A.; Baumvol, Israel J.R.

    2010-01-01

    Research highlights: → The premature failure of an aluminium injection die with a duplex surface treatment (plasma nitriding and physical vapor deposition coating) was investigated. → The origin of failure was attributed to the sulfur inclusions introduced into the surface of the tool by a sulfur-impregnated grinding stone used in the final polishing operation. → The low adhesion of the CrN coating on the sulfur inclusions led to the spalling of the coating, the exposure of the substrate material and the nucleation of cracks. → New evidence is presented on the influence of surface preparation and manufacturing processes on aluminium injection tool performance. - Abstract: The premature failure of an aluminium injection die with a duplex surface treatment (plasma nitriding and physical vapor deposition coating) was investigated, in an effort to identify the causes of such premature failure of the component. The manufacturing and the operating conditions were documented. Analytical tools were used, including scanning electron microscopy with energy dispersive X-ray capability, X-ray diffraction, and instrumented microhardness testing. Preliminary observations showed a microstructure of coarse tempered martensite, and a considerably rough surface with porosity and cracks. A detailed analysis of crack initiation sites identified sulfur inclusions in the subsurface, underneath the coating. A further revision of the processing conditions revealed that a sulfur-impregnated grinding stone had been used to polish the die. The chemical composition of such grinding stone matched that of the inclusions found in the subsurface of the failed component. Thus, searched causes of premature failure could be discussed on the lights of the present findings.

  3. Atmospheric pressure plasma-assisted femtosecond laser engraving of aluminium

    Science.gov (United States)

    Gerhard, Christoph; Gimpel, Thomas; Tasche, Daniel; Koch née Hoffmeister, Jennifer; Brückner, Stephan; Flachenecker, Günter; Wieneke, Stephan; Schade, Wolfgang; Viöl, Wolfgang

    2018-05-01

    In this contribution, we report on the impact of direct dielectric barrier discharge argon plasma at atmospheric pressure on femtosecond laser engraving of aluminium. It is shown that the assisting plasma strongly affects the surface geometry and formation of spikes of both laser-engraved single lines and patterns of adjacent lines with an appropriate overlap. Further, it was observed that the overall ablation depth is significantly increased in case of large-scale patterning whereas no notable differences in ablation depth are found for single lines. Several possible mechanisms and underlying effects of this behaviour are suggested. The increase in ablation depth is supposed to be due to a plasma-induced removal of debris particles from the cutting point via charging and oxidation as supported by EDX analysis of the re-solidified debris. Furthermore, the impact of a higher degree of surface wrinkling as well as direct interactions of plasma species with the aluminium surface on the ablation process are discussed.

  4. Development of textile-reinforced carbon fibre aluminium composites manufactured with gas pressure infiltration methods

    OpenAIRE

    W. Hufenbach; M. Gude; A. Czulak; J. Śleziona; A. Dolata-Grosz; M. Dyzia

    2009-01-01

    Purpose: The aim of his paper is to show potential of textile-reinforced carbon fibre aluminium composite with advantage of the lightweight construction of structural components subjected to thermo-mechanical stress.Design/methodology/approach: The manufacture of specimens of the carbon fibre-reinforced aluminium was realised with the aid of an advanced differential gas pressure infiltration technique, which was developed at ILK, TU Dresden.Findings: The gas pressure infiltration technology e...

  5. Development of multilayer coatings for forming dies and tools of aluminium alloy from liquid state

    International Nuclear Information System (INIS)

    Torres, E; Ugues, D; Brytan, Z; Perucca, M

    2009-01-01

    In this work, a nanocomposite (Cr,Al) x N 1-x /Si 3 N 4 coating system was deposited on H11 hot work tool steel, using the Lateral Arc Rotating Cathodes (LARC (registered) ) deposition system and modulating the chemical composition of the chromium and aluminium-silicon content. Structural characterizations were performed using scanning electron microscopy, equipped with energy dispersive spectroscopy probe, and applying x-ray diffraction, for the evaluation of phase constitution and crystallite size. In addition to the structural features, the coatings' resistance to cyclic immersions in molten aluminium alloy was evaluated. The deposited CrAlSiN coatings exhibited an fcc-Cr 1-x Al x N type structure with different aluminium contents, which directly influence hardness and wear and fatigue resistance in cyclic immersion tests. The main failure modes that occurred on the coatings' surface were soldering and thermal fatigue cracks mainly in the form of heat checks. The aluminium rich coatings were able to withstand about 15 000 cycles, whereas the decrease in the aluminium content in the coatings results in a decrease in the resistance to the immersion in molten aluminium bath. It is worthwhile to note that uncoated H11, subjected to similar testing conditions, withstood at maximum 5000 cycles.

  6. Formulation of anisotropic Hill criteria for the description of an aluminium alloy behaviour during the channel die compression test

    International Nuclear Information System (INIS)

    Gavrus, A.; Francillette, H.

    2007-01-01

    During the last years the study of the plastic deformation modes and the anisotropic mechanical behaviour of aluminium alloys have been the subject of many investigations. This paper deals with a phenomenological identification of an anisotropic Hill constitutive equation of aluminium AU4G samples using a channel die compression device at room temperature. By considering the different possible orientations of the samples in the channel die device, three initial textures, named ND (normal direction Z), LD (longitudinal direction X) and TD (transverse direction Y), were defined with the corresponding stresses σND, σLD and σTD. To describe the anisotropy of the material, a quadratic Hill criteria is used. An Avrami type equation based on the mixture of the hardening and softening phenomena is used to describe variation of each stress component with the equivalent plastic strain. The identification of the parameters of the law is made using an identification software (OPTPAR) and a good correlation between the experimental stresses and computed ones is obtained. The variation of the Hill parameters with a proposed equivalent strain, describing the deformation history of the material, is analysed. Finally, using the expressions of F, G, H and N, the constitutive equation of the normal anisotropy in the plane XY is obtained

  7. Economical surface treatment of die casting dies to prevent soldering in high pressure casting

    International Nuclear Information System (INIS)

    Fraser, D.T.; Jahedi, M.Z.

    2001-01-01

    This paper describes the use of a gas oxidation treatment of H13 tool steel to develop a compact iron oxide layer at the surface of core pins to prevent soldering in high pressure die casting. The performance of oxide layers in the protection of die steel against soldering during high pressure die casting was tested in a specially designed die using removable core pins and Al-11 Si-3 Cu casting alloy. The gas oxidation treatment can be applied at low temperatures and to large areas of the die surface. In addition this process is very cost effective compared to other coating processes such as physical vapour deposition (PVD), or thermo-reactive diffusion (TRD) coatings. This work demonstrated that surface treatment producing pure magnetite (Fe 3 O 4 ) layers are more protective than oxide layers containing a combination of Fe 3 O 4 (magnetite) and Fe 3 O 3 (haematite). The magnetite layer acts as a barrier between the die steel/casting alloy interface and prevents the formation of inter-metallic phases. Optical microscopy and scanning electron microscope were used to determine the thickness of the oxide layer, while X-ray diffraction was performed to determine the oxide phase structure

  8. Optimum back-pressure forging using servo die cushion

    OpenAIRE

    Kawamoto, Kiichiro; Yoneyama, Takeshi; Okada, Masato; Kitayama, Satoshi; Chikahisa, Junpei

    2014-01-01

    This study focused on utilizing a servo die cushion (in conjunction with a servo press) as a "back-pressure load generator," to determine its effect on shape accuracy of the formed part and total forming load in forward extrusion during cold forging. The effect of back-pressure load application was confirmed in experiments, and the optimum setting pattern of back-pressure load was considered to minimize both shape accuracy of the formed part and back-pressure energy, which was representative ...

  9. Determination of boron in uranium and aluminium by high pressure liquid chromatography (HPLC)

    International Nuclear Information System (INIS)

    Rao, Radhika M.; Aggarwal, S.K.

    2003-01-01

    Experiments were conducted for the determination of boron in U 3 O 8 powder and aluminium metal using dynamically modified reversed phase high pressure liquid chromatography (RP-HPLC) and using precolumn chromogenic agent viz. curcumin for complexing boron. The complex was separated from the excess of reagent and determined by HPLC. The boron curcumin complex (rosocyanin) was formed after extraction of boron with 2-ethyl-1,3-hexane diol (EHD). Linear calibration curves for boron amounts in the range of 0.02 μg to 0.5 μg were developed and used for the determination of boron in aluminium and uranium samples. (author)

  10. Cold pressure welding of aluminium-steel blanks: Manufacturing process and electrochemical surface preparation

    Science.gov (United States)

    Schmidt, Hans Christian; Homberg, Werner; Orive, Alejandro Gonzalez; Grundmeier, Guido; Hordych, Illia; Maier, Hans Jürgen

    2018-05-01

    In this study the manufacture of aluminium-steel blanks by cold pressure welding and their preparation for a welding process through electrochemical surface treatment are investigated and discussed. The cold pressure welding process was done with an incremental rolling tool that allows for the partial pressure welding of two blanks along a prepared path. The influence of the surface preparation by electrochemical deposition of bond promoting organosilane-based agents and roughening on a nano-scale is investigated and compared to conventional surface treatments. Coating the surfaces with a thin organosilane-based film incorporating specific functional groups should promote additional bonding between the mating oxide layers; its influence on the total weld strength is studied. Pressure welding requires suitable process strategies, and the current advances in the proposed incremental rolling process for the combination of mild steel and aluminium are presented.

  11. Optimization of die filling in high pressure die cast part using MAGMAsoft®

    DEFF Research Database (Denmark)

    Kotas, Petr; Hattel, Jesper Henri

    2008-01-01

    Integrated modeling of an entire casting process has become a tool which favors design and optimization of manufactured parts. The aim of this project was to examine and optimize a high-pressure die cast part and its production process with respect to die filling and issues of residual stresses...... in the process and machine parameters were done and assessed. All simulations revealed that, the main causes of the problems were: a poor geometry of the casting leading to an improper filling pattern, and a massive gating system bringing thermal imbalance into the solidification process. Thus deformations due...... to residual stresses occurred. The numerical results were evaluated and appeared to be in agreement with the results from the actual manufacturing process. Based on these findings, proposals for improvements were given. In order to avoid distortions and cold shuts further geometrical adjustments should...

  12. The effect of pressure and temperature on aluminium hydrolysis: Implications to trace metal scavenging in natural waters

    Digital Repository Service at National Institute of Oceanography (India)

    DileepKumar, M.

    Removal of aluminium through precipitation/scavenging in natural waters was evaluated based on its hydrolysis at different temperatures and pressures. In general, pH for the occurrence of cation hydrolysis was lowered with hike in temperature which...

  13. First results on nitriding aluminium alloys in a low-pressure RF plasma

    International Nuclear Information System (INIS)

    Fewell, M.P.; Priest, J.M.; Collins, G.A.; Short, K.T.

    2000-01-01

    Full text: Aluminium alloys are now well established as materials of choice for many commercial applications, especially where strength-to-weight ratio is a critical parameter. However, their more widespread use is inhibited by their low surface hardness. For steels, similar problems can be overcome by nitriding. The nitrogen-rich surface layer has high hardness and load-bearing capacity, and is very well bonded to the substrate. The development of a similar surface-treatment process for aluminium alloys is clearly a desirable goal. It is therefore not surprising that many research groups worldwide have attempted to nitride aluminium. Much of this work studied pure aluminium, a material of no interest for structural applications. Previous investigations into nitriding aluminium alloys' had indifferent results. However, they have served to identify the key issues, which are the importance of a pre-cleaning steps to remove the surface oxide, of impurity control during the nitriding and the desirability of using as low a process temperature as possible. In all of these areas, our process using a low-pressure RF plasma is likely to be competitive. In view of this, we have undertaken a comparative study of a range of commercially available aluminium alloys. All treatments were carried out in the hot-wall nitriding reactor at ANSTO. The samples consist of disks 25mm in diameter and ∼3mm thick which were polished and ultrasonically cleaned in alcohol prior to treatment. The samples were stored in air at all times except when in the nitriding reactor. In a series of treatments, the treatment time was varied in the range 1-16 h and the temperature in the range 350-500 deg C. All treatments were preceeded by a plasma cleaning step in a H 2 /50%Ar mixture for a duration of 1.5-2.0 h while the reactor reached processing temperature. The treatments all used pure N 2 at a pressure of 0.4Pa and a nitrogen flow rate of 12μmol s -1 , with 245W of rf power at 13.56MHz applied to

  14. Wear performance of garnet aluminium composites at high contact pressure

    Science.gov (United States)

    Sharma, Anju; Arora, Rama; Kumar, Suresh; Singh, Gurmel; Pandey, O. P.

    2016-05-01

    To satisfy the needs of the engineering sector, researchers and material scientists in this area adopted the development of composites with tailor made properties to enhance efficiency and cost savings in the manufacturing sector. The technology of the mineral industry is shaping the supply and demand of minerals derived materials. The composites are best classified as high performance materials have high strength-to-weight ratios, and require controlled manufacturing environments for optimum performance. Natural mineral garnet was used as the reinforcement of composite because of satisfactory mechanical properties as well as an attractive ecological alternative to others ceramics. For this purpose, samples have been prepared with different sizesof the garnet reinforcement using the mechanical stirring method to achieve the homogeneously dispersed strengthening phase. A systematic study of the effect of high contact pressure on the sliding wear behaviour of garnet reinforced LM13 alloy composites is presented in this paper. The SEM analysis of the worn samples and debris reveals the clues about the wear mechanism. The drastic improvement in the wear resistance of the composites at high contact pressure shows the high potential of the material to be used in engineering applications.

  15. High pressure die casting of Fe-based metallic glass

    Science.gov (United States)

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-01-01

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications. PMID:27725780

  16. High pressure die casting of Fe-based metallic glass.

    Science.gov (United States)

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-10-11

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

  17. High pressure die casting of Fe-based metallic glass

    Science.gov (United States)

    Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

    2016-10-01

    Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

  18. Effect of the temperature and the chlorine pressure, over the aluminium chlorides obtained by direct chlorination of the 6061 alloy

    International Nuclear Information System (INIS)

    Alvarez, Fabiola J.; Bohe, Ana E.; Pasquevich, Daniel M.

    2003-01-01

    The aluminium chloride is synthesized by direct chlorination of aluminium, in agreement with the following reaction: Al(s) + 3/2 Cl 2 AlCl 3 (s,g).The present work focuses on the preparation of aluminium chlorides by two methods: (a) Chlorination of 6061 aluminium alloy with gaseous chlorine in sealed containers, filled with different pressures of gas, from 0.8 to 74 Kpa and in the range of temperature between 200 0 and 500 0 C.(b) Chlorination of the same alloy in chlorine flow between 150 0 and 400 0 C.In the sealed systems, the hexahydrated aluminium trichloride predominated over the anhydrous form. For pressures lower than 14 Kpa and temperatures under 250 0 C, the chloride didn't appear.The residues were rich in aluminium, chlorine and magnesium.In the other systems, the anhydrous chloride was found in the areas of the reactor of temperatures above 100 0 C, for all the thermal treatments. The waste was composed by CrCl 3 and AlCl 3 .6H 2 O.The influence of the chlorine pressures and the heating temperature over the characteristics of the product, was studied.The characterization techniques were x-ray diffraction and energy dispersive spectroscopy, and the evolution of the structure was followed by scanning electron microscopy

  19. Modeling of high temperature- and diffusion-controlled die soldering in aluminum high pressure die casting

    DEFF Research Database (Denmark)

    Domkin, Konstantin; Hattel, Jesper Henri; Thorborg, Jesper

    2009-01-01

    of the die lifetime based on a quantitative analysis of die soldering in the framework of the numerical simulations of the die-casting process. Full 3D simulations of the process, including the filling. solidification, and the die cooling, are carried out using the casting simulation software MAGMAsoft....... The resulting transient temperature fields on the die surface and in the casting are then post-processed to estimate the die soldering. The present work deals only with the metallurgical/chemical kind of soldering which occurs at high temperatures and involves formation and growth of intermetallic layers...

  20. Numerical simulation of low pressure die-casting aluminum wheel

    Directory of Open Access Journals (Sweden)

    Mi Guofa

    2009-02-01

    Full Text Available The FDM numerical simulation software, ViewCast system, was employed to simulate the low pressure die casting (LPDC of an aluminum wheel. By analyzing the mold-fi lling and solidifi cation stage of the LPDC process, the distribution of liquid fraction, temperature field and solidification pattern of castings were studied. The potential shrinkage defects were predicted to be formed at the rim/spoke junctions, which is in consistence with the X-ray detection result. The distribution pattern of the defects has also been studied. A solution towards reducing such defects has been presented. The cooling capacity of the mold was improved by installing water pipes both in the side mold and the top mold. Analysis on the shrinkage defects under forced cooling mode proved that adding the cooling system in the mold is an effective method for reduction of shrinkage defects.

  1. Evaluation of interlocking bond strength between structured 1.0338 steel sheets and high pressure die cast AlMg5Si2

    Science.gov (United States)

    Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

    2018-05-01

    Multi-material components open up new possibilities for functional design. Such components combine beneficial physical properties of different materials in a single component as for instance chemical resistance, high strength or low density. The challenge is a reliable bond between both materials to enable a long term usage. This paper deals with a form closure connection to ensure a solid connection between steel strips and high pressure die cast aluminium. Two different sizes of channel structures with width ratios of 1.0 and 1.35 are produced on a steel sheet. An ensuing flat rolling pass is performed to create undercuts with a width of up to 50 µm, enabling an interlocking of the molten aluminium in the concluding casting process. For both rolling processes the resulting geometry is analysed depending on the thickness reduction. In a subsequent high pressure die casting process, aluminium is applied resulting in a complete form filling for the coarser structure. Comparing structures with and without undercuts, only structures suited with undercuts remain gap-free after solidification contraction. The finer structure could not be filled completely; nevertheless these structures result in shear strength of up to 45 MPa transversal to the channel-direction.

  2. Development of a commercial Transducer for Measuring Pressure and Friction on the Model Die Surface

    DEFF Research Database (Denmark)

    Andersen, Claus Bo; Ravn, Bjarne Gottlieb; Wanheim, Tarras

    2001-01-01

    deflection in the tool causes incorrect shape of the final component. The dinemsions of the die-cavity have to be corrected taking into account die deflection due to the high internal pressure. The modelling material technique is suitable for measuring internal pressure, but so far only a transducer...... to measure normal pressure has been available....

  3. An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes

    International Nuclear Information System (INIS)

    Suarez-Pena, B.; Asensio-Lozano, J.

    2009-01-01

    In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs

  4. Tribological Properties of AlSi11-SiCp Composite Castings Produced by Pressure Die Casting Method

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2014-08-01

    Full Text Available The measurement results concerning the abrasive wear of AlSi11-SiC particles composites are presented in paper. The method of preparing a composite slurry composed of AlSi11 alloy matrix and 10, 20% vol.% of SiC particles, as well as the method of its high-pressure die casting was described. Composite slurry was injected into metal mould of cold chamber pressure die cast machine and castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. Very good uniform arrangement of SiC particles in volume composite matrix was observed and these results were publicated early in this journal. The kinetics of abrasive wear and correlation with SiC particles arrangement in composite matrix were presented. Better wear resistance of composite was observed in comparison with aluminium alloy. Very strong linear correlation between abrasive wear and particle arrangement was observed. The conclusion gives the analysis and the interpretation of the obtained results.

  5. Study of radial die-wall pressure changes during pharmaceutical powder compaction.

    Science.gov (United States)

    Abdel-Hamid, Sameh; Betz, Gabriele

    2011-04-01

    In tablet manufacturing, less attention is paid to the measurement of die-wall pressure than to force-displacement diagrams. Therefore, the aim of this study was to investigate radial stress change during pharmaceutical compaction. The Presster(TM), a tablet-press replicator, was used to characterize compaction behavior of microcrystalline cellulose (viscoelastic), calcium hydrogen phosphate dihydrate (brittle), direct compressible mannitol (plastic), pre-gelatinized starch (plastic/elastic), and spray dried lactose monohydrate (plastic/brittle) by measuring radial die-wall pressure; therefore powders were compacted at different (pre) compaction pressures as well as different speeds. Residual die-wall pressure (RDP) and maximum die-wall pressure (MDP) were measured. Various tablet physical properties were correlated to radial die-wall pressure. With increasing compaction pressure, RDP and MDP (P compaction behavior of materials and detecting friction phenomena in the early stage of development.

  6. Procedure of a secure design calculation for transmission housings made of aluminium die cast; Ablauf einer sicheren Auslegungsberechnung von Getriebegehaeusen aus Aluminiumdruckguss

    Energy Technology Data Exchange (ETDEWEB)

    Varenkamp, Marco; Schoen, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany). Fachbereich Berechnung und Simulation

    2011-07-01

    The challenges in life time calculation of transmission housings made of aluminium die cast are on the one hand the complex geometry of the parts and on the other hand the defects in the material such as pores resulting from the die-cast process. The calculations are carried out using the finite element method and the local strain approach. The problem of transferability within the local strain approach is mastered by comparison with component tests and improvement of the transfer functions based on statistical evaluation. The secure design is assured by a safety factor derived from the confidence probability. With the help of an example the procedure will be explained. In addition it will be shown that under uniaxial variable amplitude loading the calculation result can be improved using the damage parameter PJ. (orig.)

  7. Butt pressure welding of wheels from vehicles consisting of steel and aluminium; Pressstumpfschweissen von Fahrzeugraedern aus Stahl und Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Grobelin, K. [Hess Engineering AG, Frauenfeld (Switzerland)

    2001-07-01

    Every year in Europe 35 million wheels for vehicles are produced. Most of them are wheels consisting of metal tapes, both of steel and of aluminium alloys. The manufacturing of wheels is explained, in detail the method known as DC upset welding used for butt joints of wheel-rims. The engaged machinery, the specials of welding various materials, the limits of the method, and the quality assurance are discussed. Advantages of the applied method are joints of first-class quality, high productivity, energy saving and environmental cleanness. (orig.)

  8. Stress distribution and pressure-bearing capacity of a high-pressure split-cylinder die with prism cavity

    Science.gov (United States)

    Zhao, Liang; Li, Mingzhe; Wang, Liyan; Qu, Erhu; Yi, Zhuo

    2018-03-01

    A novel high-pressure belt-type die with a split-type cylinder is investigated with respect to extending its lifetime and improving its pressure bearing capacity. Specifically, a tungsten carbide cylinder is split into several parts along the radial direction with a prism-type cavity. In this paper, the cylinders with different split numbers are chosen to study the stress distribution and compare them with the traditional belt-type die. The simulation results indicate that the split cylinder has much smaller stress than those in the belt-type cylinder, and the statistical analysis reveals that the split-pressure cylinder is able to bear higher pressure. Experimental tests also show that the high-pressure die with a split cylinder and prism cavity has a stronger pressure-bearing capacity than a belt-type die. The split cylinder has advantages of easy manufacturing, high pressure bearing capacity, and replaceable performance.

  9. Effect of Dynamic Pressure on the Performance of Thermoacoustic Refrigerator with Aluminium (Al) Resonator

    Science.gov (United States)

    Arya, Bheemsha; Nayak, B. Ramesh; Shivakumara, N. V.

    2018-04-01

    In practice the refrigerants are being used in the conventional refrigeration system to get the required cooling effect. These refrigerants produce Chlorofluorocarbons (CFCs) and Hydro chlorofluorocarbons (HCFCs) which are highly harmful to the environment, particularly depleting of ozone layers resulting in green house emissions. In order to overcome these effects, the research needs to be focused on the development of an ecofriendly refrigeration system. The thermoacoustic refrigeration system is one among such system where the sound waves are used to compress and expand the gas particles. This study focuses on the effect of dynamic pressure on the thermoacoustic refrigerator made of aluminium with overall length of 748.82 mm, and the entire inner surface of the resonator tube was coated with 2mm thickness of polyurethane to minimize the heat losses to the atmosphere. Experiments were conducted with different stack geometries i.e. parallel plates having 0.119 mm thick with spacing between the plates maintained at 0.358 mm, 1mm diameter pipes, 2mm diameter pipes and 4 mm diameter pipes. Experiments were also conducted with different drive ratios of 0.6%, 1% and 1.6% for a constant dynamic pressure of 2 bar and 10 bar for helium and air as working medium. The results were plotted with the help of graphs, the variation of coefficient of performance (COP) and the relative coefficient of performance (COPR) for the above said conditions were calculated.

  10. Characterization of metal powder based rapid prototyping components under aluminium high pressure die casting process conditions

    CSIR Research Space (South Africa)

    Pereira, MFVT

    2009-11-01

    Full Text Available periodic inspections, monitoring crack formation and evidence of surface washout. At the end of the thermal tests, mechanical strength and hardness tests were performed to assess toughness and core resistance variations in relation to the initial conditions...

  11. Metallographic assessment of Al-12Si high-pressure die casting escalator steps.

    Science.gov (United States)

    Vander Voort, George Frederic; Suárez-Peña, Beatriz; Asensio-Lozano, Juan

    2014-10-01

    A microstructural characterization study was performed on high-pressure die cast specimens extracted from escalator steps manufactured from an Al-12 wt.% Si alloy designed for structural applications. Black and white, color light optical imaging and scanning electron microscopy techniques were used to conduct the microstructural analysis. Most regions in the samples studied contained globular-rosette primary α-Al grains surrounded by an Al-Si eutectic aggregate, while primary dendritic α-Al grains were present in the surface layer. This dendritic microstructure was observed in the regions where the melt did not impinge directly on the die surface during cavity filling. Consequently, microstructures in the surface layer were nonuniform. Utilizing physical metallurgy principles, these results were analyzed in terms of the applied pressure and filling velocity during high-pressure die casting. The effects of these parameters on solidification at different locations of the casting are discussed.

  12. Aluminium production

    International Nuclear Information System (INIS)

    Winter, B.; Ayers, J.; Sammer, G.

    2001-01-01

    Aluminium is the most important non-ferrous metal by quantity. Aluminium is produced by electrolysis of aluminium oxide (also known as alumina). Alumina is produced by refining bauxite. The quantity of primary and secondary aluminium production in ECE-countries between 1992 and 1998 is shown. The European aluminium industry employs approximately 200 000 employees. The annual aluminium production in the European Union was 3.58 million tonnes in 1994, of which 44 % was secondary aluminium. In 1996 3.96 million tonnes of aluminium were produced in the EU, of which 44 % was secondary aluminium. (author)

  13. Modeling and Analysis of The Pressure Die Casting Using Response Surface Methodology

    International Nuclear Information System (INIS)

    Kittur, Jayant K.; Herwadkar, T. V.; Parappagoudar, M. B.

    2010-01-01

    Pressure die casting is successfully used in the manufacture of Aluminum alloys components for automobile and many other industries. Die casting is a process involving many process parameters having complex relationship with the quality of the cast product. Though various process parameters have influence on the quality of die cast component, major influence is seen by the die casting machine parameters and their proper settings. In the present work, non-linear regression models have been developed for making predictions and analyzing the effect of die casting machine parameters on the performance characteristics of die casting process. Design of Experiments (DOE) with Response Surface Methodology (RSM) has been used to analyze the effect of effect of input parameters and their interaction on the response and further used to develop nonlinear input-output relationships. Die casting machine parameters, namely, fast shot velocity, slow shot to fast shot change over point, intensification pressure and holding time have been considered as the input variables. The quality characteristics of the cast product were determined by porosity, hardness and surface rough roughness (output/responses). Design of experiments has been used to plan the experiments and analyze the impact of variables on the quality of casting. On the other-hand Response Surface Methodology (Central Composite Design) is utilized to develop non-linear input-output relationships (regression models). The developed regression models have been tested for their statistical adequacy through ANOVA test. The practical usefulness of these models has been tested with some test cases. These models can be used to make the predictions about different quality characteristics, for the known set of die casting machine parameters, without conducting the experiments.

  14. Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

    Directory of Open Access Journals (Sweden)

    GUO Zhi-peng

    2007-02-01

    Full Text Available The high pressure die casting (HPDC process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today’s manufacturing industry.In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were Measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger,and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified,when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

  15. Semi-solid high pressure die casting of metal matrix composites produced by liquid state processing

    CSIR Research Space (South Africa)

    Ivanchev, L

    2012-10-01

    Full Text Available stirring. The composite was then transferred to a High Pressure Die Casting (HPDC) machine in the semi-solid state. The micron size particles were found to be predominantly in the intergranular eutectic while the nano-particles were predominantly...

  16. Modeling of microstructure evolution of magnesium alloy during the high pressure die casting process

    International Nuclear Information System (INIS)

    Wu Mengwu; Xiong Shoumei

    2012-01-01

    Two important microstructure characteristics of high pressure die cast magnesium alloy are the externally solidified crystals (ESCs) and the fully divorced eutectic which form at the filling stage of the shot sleeve and at the last stage of solidification in the die cavity, respectively. Both of them have a significant influence on the mechanical properties and performance of magnesium alloy die castings. In the present paper, a numerical model based on the cellular automaton (CA) method was developed to simulate the microstructure evolution of magnesium alloy during cold-chamber high pressure die casting (HPDC) process. Modeling of dendritic growth of magnesium alloy with six-fold symmetry was achieved by defining a special neighbourhood configuration and calculating of the growth kinetics from complete solution of the transport equations. Special attention was paid to establish a nucleation model considering both of the nucleation of externally solidified crystals in the shot sleeve and the massive nucleation in the die cavity. Meanwhile, simulation of the formation of fully divorced eutectic was also taken into account in the present CA model. Validation was performed and the capability of the present model was addressed by comparing the simulated results with those obtained by experiments.

  17. Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

    Science.gov (United States)

    Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

    Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

  18. Attachment of MEM piezoresistive silicon pressure sensor dies using different adhesives

    Directory of Open Access Journals (Sweden)

    Jović Vesna B.

    2011-01-01

    Full Text Available This paper gives comparison and discussion of adhesives used for attachment of silicon piezoresistive pressure sensor dies. Special attention is paid on low pressure sensor dies because of their extreme sensitivity on stresses, which can arise from packaging procedure and applied materials. Commercially available adhesives “Scotch Weld 2214 Hi-Temp” from “3M Co.” and “DM2700P/H848” from “DIEMAT”, USA, were compared. First of them is aluminum filled epoxy adhesive and second is low melting temperature (LMT glass paste. Comparing test results for low pressure sensor chips we found that LMT glass (glass frit is better adhesive for this application. Applying LMT glass paste minimizes internal stresses caused by disagreement of coefficients of thermal expansions between sensor die and housing material. Also, it minimizes stresses introduced during applying external loads in the process of pressure measuring. Regarding the measurements, for the sensors installed with filled epoxy paste, resistor for compensation of temperature offset change had negative values in all cases, which means that linear temperature compensation, of sensors installed this way, would be impossible. In the sensors installed with LMT glass paste, all results, without exception, were in their common limits (values, which give the possibility of passive temperature compensation. Furthermore, LMT glass attachment can broaden temperature operating range of MEM silicon pressure sensors towards higher values, up to 120 ºC.

  19. Influence of refining process on the porosity of high pressure die casting alloy Al-Si

    Directory of Open Access Journals (Sweden)

    A.W. Orlowicz

    2009-04-01

    Full Text Available This study presents research results of the influence that refining and transfer of AlSi12S alloy on the porosity of high pressure diecastings.Tests were conducted under production conditions of Die-casting Foundry META-ZEL Sp z o.o. The operation of refining was conducted in a melting furnace, with the use of an FDU Mini Degasser. Decay of the refining effect was assessed by evaluating the porosity content and metallographic examination.

  20. New trends in cold-chamber die casting machine design

    Directory of Open Access Journals (Sweden)

    R. Dańko

    2015-07-01

    Full Text Available Larger and larger proportions of aluminium castings, especially those produced by the die casting process, can be observed during recent years in the automotive industry, house-hold articles and others. In case of the automotive industry, apart from the traditional elements produced by the die pressure method such as engine blocks or crank shaft bedplates, aluminium is displacing steel from structural parts of cars (‘body in white’. The current state and development directions of the structural solutions of cold-chamber die castings are analysed in this paper. These solutions drive the prospective development of these machines and die casting technology. The focus is mainly on essential functional systems such as: hydraulic drives of closing and locking units, as well as pressing in die machines of known companies present on the European market.

  1. The compatibility of chromium-aluminium steels with high pressure carbon dioxid at intermediate- temperatures; Compatibilite des aciers au chrome-aluminium avec le gaz carbonique sous pression aux temperatures moyennes

    Energy Technology Data Exchange (ETDEWEB)

    Leclercq, D; Loriers, H; David, R; Darras, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    With a view to their use in the exchangers of nuclear reactors of the graphite-gas or heavy water-gas types, the behaviour of chromium-aluminium steels containing up to 7 per cent chromium and 1.5 per cent aluminium has been studied in the presence of high-pressure carbon dioxide at temperatures of between 400 and 700 deg. C. The two most interesting grades of steel (2 per cent Cr - 0.35 per cent Al - 0.35 per cent Mo and 7 per cent Cr - 1.5 per cent Al - 0.6 per cent Si) are still compatible with carbon dioxide up to 550 and 600 deg. C respectively. A hot dip aluminised coating considerably increases resistance to oxidation of the first grade and should make possible its use up to temperatures of at least 600 deg. C. (authors) [French] Dans l'optique de leur emploi dans les echangeurs de reacteurs nucleaires des filieres graphite-gaz ou eau lourde-gaz, le comportement en presence de gaz carbonique sous pression d'aciers au chrome-aluminium, contenant jusqu'a 7 pour cent de chrome et 1,5 pour cent d'aluminium a ete etudie entre 400 et 700 deg. C. Les deux nuances les plus interessantes (2 pour cent Cr - 0,35 pour cent Al - 0,35 pour cent Mo et 7 pour cent Cr - 1,5 pour cent Al - 0,6 pour cent Si) restent compatibles avec le gaz carbonique jusqu'a 550 et 600 deg. C respectivement. Un revetement d'aluminium, effectue par immersion dans un bain fondu, ameliore notablement la resistance a l'oxydation de la premiere et doit permettre son empioi jusqu'a 600 deg. C au moins. (auteurs)

  2. Piezoresistive pressure sensor using low-temperature aluminium induced crystallization of sputter-deposited amorphous silicon film

    International Nuclear Information System (INIS)

    Tiwari, Ruchi; Chandra, Sudhir

    2013-01-01

    In the present work, we have investigated the piezoresistive properties of silicon films prepared by the radio frequency magnetron sputtering technique, followed by the aluminium induced crystallization (AIC) process. Orientation and grain size of the polysilicon films were studied by x-ray diffraction analysis and found to be in the range 30–50 nm. Annealing of the Al–Si stack on an oxidized silicon substrate was performed in air ambient at 300–550 °C, resulting in layer exchange and transformation from amorphous to polysilicon phase. Van der Pauw and Hall measurement techniques were used to investigate the sheet resistance and carrier mobility of the resulting polycrystalline silicon film. The effect of Al thickness on the sheet resistance and mobility was also studied in the present work. A piezoresistive pressure sensor was fabricated on an oxidized silicon substrate in a Wheatstone bridge configuration, comprising of four piezoresistors made of polysilicon film obtained by the AIC process. The diaphragm was formed by the bulk-micromachining of silicon substrate. The response of the pressure sensor with applied negative pressure in 10–95 kPa range was studied. The gauge factor was estimated to be 5 and 18 for differently located piezoresistors on the diaphragm. The sensitivity of the pressure sensor was measured to be ∼ 30 mV MPa −1 , when the Wheatstone bridge was biased at 1 V input voltage. (paper)

  3. The simulation of magnesium wheel low pressure die casting based on PAM-CASTTM

    International Nuclear Information System (INIS)

    Peng Yinghong; Wang Yingchun; Li Dayong; Zeng Xiaoqin

    2004-01-01

    Magnesium is the lightest metal commonly used in engineering, with various excellent characteristics such as high strength and electromagnetic interference shielding capability. Particularly, the usage of magnesium in automotive industry can meet better the need to reduce fuel consumption and CO2 emissions. Nowadays, most current magnesium components in automobiles are made by die casting. In this paper, commercial software for die casting, PAM-CAST TM , was utilized to simulate the low pressure die casting process of magnesium wheel. Through calculating temperature field and velocity field during filling and solidification stages, the evolution of temperature distribution and liquid fraction was analyzed. Then, the potential defects including the gas entrapments in the middle of the spokes, shrinkages between the rim and the spokes were forecasted. The analytical results revealed that the mold geometry and die casting parameters should be improved in order to get the sound magnesium wheel. The reasons leading to these defects were also analyzed and the solutions to eliminate them were put forward. Furthermore, through reducing the pouring velocity, the air gas entrapments and partial shrinkages were eliminated effectively

  4. Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

    Energy Technology Data Exchange (ETDEWEB)

    Dr. John J. Moore; Dr. Jianliang Lin,

    2012-07-31

    The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain the largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).

  5. Numerical simulation and optimization of Al alloy cylinder body by low pressure die casting

    Directory of Open Access Journals (Sweden)

    Mi Guofa

    2008-05-01

    Full Text Available Shrinkage defects can be formed easily at Critical location during low pressure die casting (LPDC of aluminum alloy cylinder body. It has harmful effect on the products. Mold fi lling and solidifi cation process of a cylinder body was simulated by using of Z-CAST software. The casting method was improved based on the simulation results. In order to create effective feeding passage, the structure of casting was modifi ed by changing the location of strengthening ribs at the bottom, without causing any adverse effect on the part’s performance. Inserting copper billet at suitable location of the die is a valid way to create suitable solidifi cation sequence that is benefi cial to the feeding. Using these methods, the shrinkage defect was completely eliminated at the critical location.

  6. Accelerated growth of oxide film on aluminium alloys under steam: Part II: Effects of alloy chemistry and steam vapour pressure on corrosion and adhesion performance

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Bordo, Kirill; Jellesen, Morten Stendahl

    2015-01-01

    The steam treatment of aluminium alloys with varying vapour pressure of steamresulted in the growth of aluminium oxyhydroxide films of thickness range between 450 - 825nm. The surface composition, corrosion resistance, and adhesion of the produced films was characterised by XPS, potentiodynamic p...... of the vapour pressure of the steam. The accelerated corrosion and adhesion tests on steam generated oxide films with commercial powder coating verified that the performance of the oxide coating is highly dependent on the vapour pressure of the steam....... polarization, acetic acid salt spray, filiform corrosion test, and tape test. The oxide films formed by steam treatment showed good corrosion resistance in NaCl solution by significantly reducing anodic and cathodic activities. The pitting potential of the surface treated with steam was a function...

  7. An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

    OpenAIRE

    J. Mutwil

    2008-01-01

    A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order t...

  8. The effects of moderate die pressure on banana-peel briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Wilaipon, P. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering]|[Narasuan Univ., Phitsanulok (Thailand). Faculty of Engineering; Trirattanasirichai, K.; Tangchaichit, K. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering

    2006-07-01

    Bananas are one of the most important crops in Thailand, and are now being considered as a renewable energy source. This study investigated the impacts of moderate die pressure on banana peel briquettes. The pressure range in the study was set at 3-11 MPa. Water resistance characteristics were also analyzed. Four factors were considered: (1) the relaxation in length of the briquettes; (2) impact resistance; (3) relaxation in volume; and (4) water resistance. Experiments were conducted in laboratory conditions with humidity set at between 50 and 60 per cent at 27 degrees C. An impact resistance test was performed 168 hours after the briquetting process. The briquettes were immersed in water in order to conduct the water resistance test. Results of the tests demonstrated a rapid increase in the length of the briquettes. The maximum percentage of elongation occurred within 1 hour after being removed from the die. Results of the strength tests showed that the briquettes had a compaction pressure over 5 MPa. The briquettes showed significant potential as a biomass fuel. 15 refs., 1 tab., 12 figs.

  9. Casting defects and mechanical properties of high pressure die cast Mg-Zn-Al-RE alloys

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Wenlong; Easton, Mark A.; Zhu, Suming; Nie, Jianfeng [CAST Cooperative Research Centre, Department of Materials Engineering Monash University, Melbourne, VIC (Australia); Dargusch, Matthew S. [School of Mechanical and Mining Engineering, University of Queensland, Brisbane, QLD (Australia); Gibson, Mark A. [CSIRO Process Science and Engineering, Melbourne, VIC (Australia); Jia, Shusheng [Key Laboratory of Automobile Materials, Ministry of Education, Department of Materials Science and Engineering Jilin University, Changchun (China)

    2012-02-15

    The die casting defects and tensile properties of high pressure die cast (HPDC) Mg-Zn-Al-RE alloys with various combinations of Zn and Al were studied. The results show that die casting defects in Mg-Zn-Al-RE alloys are affected by the percentage of Zn and Al contents. The hot tearing susceptibility (HTS) of Mg-Zn-Al-RE alloys tends to increase with increasing Zn content up to 6 wt%, while a further increase of Al and/or Zn content reduces the HTS. In tensile tests, the yield strength (YS) is generally improved by increasing Zn or Al content, whereas the tensile strength (TS) and ductility appear to depend largely on the presence of casting defects. Compared with Mg-Zn-Al alloys, the mechanical properties of the Mg-Zn-Al-RE alloy are significantly improved. The Mg-4Zn-4Al-4RE alloy is found to have few casting defects and the optimal tensile properties. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  10. Simulation of distortion and residual stress in high pressure die casting – modelling and experiments

    International Nuclear Information System (INIS)

    Hofer, P; Kaschnitz, E; Schumacher, P

    2012-01-01

    Two individual high-pressure die-casting geometries were developed in order to study the influence of process parameters and different alloys on the distortion behaviour of castings. These geometries were a stress lattice and a V-shaped sample tending to form residual stress due to different wall thickness respectively by a deliberate massive gating system. In the experimental castings the influence of the most important process parameters such as die temperature and die opening time and the cooling regime was examined. The time evolution of process temperatures was measured using thermal imaging. The heat transfer coefficients were adapted to the observed temperature distributions. Castings were produced from the two alloys AlSi12 and AlSi10MnMg. The distortion of the castings was measured by means of a tactile measuring device. For the alloy AlSi10MnMg thermo-physical and thermo-mechanical data were obtained using differential scanning calorimetry, laser flash technique, dilatometry and tensile testing at elevated temperatures. These data were used for modelling the material behaviour of the AlSi10MnMg alloy in the numerical model while for the alloy AlSi12(Fe) literature data were used. Process and stress simulation were conducted using the commercial FEM software ANSYS Workbench. A survey on the results of the comparison between simulation and experiment is given for both alloys.

  11. An evaluation of the pressure proof test concept for 2024-T3 aluminium alloy sheet

    Science.gov (United States)

    Dawicke, D. S.; Poe, C. C., Jr.; Newman, J. C.; Harris, C. E.

    1991-01-01

    The concept of pressure proof testing of fuselage structures with fatigue cracks to insure structural integrity was evaluated from a fracture mechanics viewpoint. A generic analytical and experimental investigation was conducted on uniaxially loaded flat panels with crack configurations and stress levels typical of longitudinal lap splice joints in commercial transport aircraft fuselages. The results revealed that the remaining fatigue life after a proof cycle was longer than that without the proof cycle because of crack growth retardation due to increased crack closure. However, based on a crack length that is slightly less than the critical value at the maximum proof stress, the minimum assured life or proof test interval must be no more than 550 pressure cycles for a 1.33 proof factor and 1530 pressure cycles for a 1.5 proof factor to prevent in-flight failures.

  12. Pressure Effects on Solid State Phase Transformation of Aluminium Bronze in Cooling Process

    International Nuclear Information System (INIS)

    Hai-Yan, Wang; Jian-Hua, Liu; Gui-Rong, Peng; Yan, Chen; Yu-Wen, Liu; Fei, Li; Wen-Kui, Wang

    2009-01-01

    Effects of high pressure (6 GPa) on the solid state phase transformation kinetic parameters of aluminum bronze during the cooling process are investigated, based on the measurement and calculation of its solid state phase transformation temperature, duration and activation energy and the observation of its microstructures. The results show that high pressure treatment can reduce the solid phase transformation temperature and activation energy in the cooling process and can shorten the phase transformation duration, which is favorable when forming fine-grained aluminum bronze

  13. Yttrium aluminium garnet under pressure: Structural, elastic, and vibrational properties from ab initio studies

    International Nuclear Information System (INIS)

    Monteseguro, V.; Rodríguez-Hernández, P.; Muñoz, A.

    2015-01-01

    The structural, elastic, and vibrational properties of yttrium aluminum garnet Y 3 Al 5 O 12 are studied under high pressure by ab initio calculations in the framework of the density functional theory. The calculated ground state properties are in good agreement with the available experimental data. Pressure dependences of bond length and bulk moduli of the constituent polyhedra are reported. The evolution of the elastic constants and the major elastic properties, Young and shear modulus, Poisson's ratios, and Zener anisotropy ratio, are described. The mechanical stability is analyzed, on the light of “Born generalized stability criteria,” showing that the garnet is mechanically unstable above 116 GPa. Symmetries, frequencies, and pressure coefficients of the Raman-active modes are discussed on the basis of the calculated total and partial phonon density of states, which reflect the dynamical contribution of each atom. The relations between the phonon modes of Y 3 Al 5 O 12 and the internal and external molecular modes of the different polyhedra are discussed. Infrared-active modes, as well as the silent modes, and their pressure dependence are also investigated. No dynamical instabilities were found below 116 GPa

  14. Application of the EC pressure equipment directive in the gas industry; Die Anwendung der EG-Druckgeraeterichtlinie in der Gaswirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Bueschel, K. [Deutscher Verein des Gas- und Wasserfaches e.V., Bonn (Germany); John, M. [Karlsruhe Univ. (T.H.) (Germany). DVGW-Forschungsstelle am Engler-Bunte-Institut; Wasser, U. [Bundesverband der Deutschen Gas- und Wasserwirtschaft e.V., Bonn (Germany)

    2000-07-01

    The EC Pressure Equipment Directive primarily concerns that broad range of equipment that falls under the Equipment Safety Act and its regulations on pressure vessels, boilers etc. Meanwhile, however, the mainstream view is that also some equipment of the gas industry is affected although its pipeline systems have been excluded from the Directive. The interpretation of the Directive must take into account this background in order to reach satisfactory conclusions in the actual application of the Directive to the components of the gas industry. (orig.) [German] Die EG-Druckgeraeterichtlinie betrifft primaer jenes grosse Geraetespektrum, das unter das Geraetesicherheitsgesetz und dessen Verordnungen zu Druckbehaeltern, Dampfkesseln etc. faellt. Inzwischen herrscht jedoch die Meinung vor, dass auch bestimmte Anlagenteile der Gaswirtschaft erfasst werden, obwohl deren Rohrleitungssysteme von der Richtlinie ausgenommen worden sind. Die Auslegung der Richtlinie muss diesen Hintergrund beachten, um zu befriedigenden Aussagen bei ihrer konkreten Anwendung auf die Komponenten der Gaswirtschaft zu gelangen. (orig.)

  15. Influence of surface liquid segregation on corrosion behavior of semi-solid metal high pressure die cast aluminium alloys

    CSIR Research Space (South Africa)

    Masuku, EP

    2010-09-01

    Full Text Available alloys 7075-T6 and 2024-T6. Potentiodynamic testing was performed in deaerated 3.5%NaCl solution. In separate tests, the open-circuit potential was monitored in aerated 3.5% NaCl for 30 minutes after immersion. The electrochemical tests show...

  16. Aluminium bridges, aluminium bridge decks

    NARCIS (Netherlands)

    Soetens, F.; Straalen, IJ.J. van

    2003-01-01

    Applications of aluminium have grown considerably in building and civil engineering the last decade. In building and civil engineering the increase of aluminium applications is due to various aspects like light weight, durability and maintenance, use of extrusions, and esthetics. The paper starts

  17. An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes; Una estrategia de ecodiseno de piezas obtenidas mediante moldeo a presion: analisis microestructrual aplicado a la desmaterializacion

    Energy Technology Data Exchange (ETDEWEB)

    Suarez-Pena, B.; Asensio-Lozano, J.

    2009-07-01

    In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs.

  18. Microstructure and Properties of Cobalt-and Zinc-Containing Magnetic Magnesium Alloys Processed by High-Pressure Die Casting

    Science.gov (United States)

    Klose, Christian; Demminger, Christian; Maier, Hans Jürgen

    The inherent magnetic properties of lightweight alloys based on magnesium and cobalt offer a novel way in order to measure mechanical loads throughout the entire structural component using the magnetoelastic effect. Because the solubility of cobalt in the magnesium matrix is negligible, the magnetic properties mainly originate from Co-rich precipitates. Thus, the size and distribution of Co-containing phases within the alloy's microstructure wields a major influence on the amplitude of the load-sensitive properties which can be measured by employing the harmonic analysis of eddy-current signals. In this study, Mg-Co-based alloys are produced by several casting methods which allow the application of different cooling rates, e.g. gravity die casting and high-pressure die casting. The differences between the manufactured alloys' micro- and phase structures are compared depending on the applied cooling rate and the superior magnetic and mechanical properties of the high-pressure die cast material are demonstrated.

  19. Failure behavior of high pressure die casting AZ91D magnesium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Li, X.; Xiong, S.M. [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China); Guo, Z., E-mail: zhipeng_guo@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China)

    2016-08-30

    The failure behavior of high pressure die casting AZ91D magnesium alloy during both tensile and fatigue tests was studied in situ by using scanning electron microscope. Attention was focused on the role of microstructure played in crack initiation and propagation. Results showed that the defects in castings, including gas pore, shrinkage pore and defect band, were the crack initiation sources. In tensile test, the crack propagated in a combination of intergranular and transgranular modes, and the specimen fractured by connecting defects at the section with minimum effective force bearing area. In fatigue test, the crack propagated in a transgranular mode at specific crystalline planes. When the crack was in contact with the β-phase, the crack would pass through, and fracture the network β-phase, whereas bypass the island β-phase by detaching it from the surrounding α-Mg grains. Besides, defects in front of the crack would act as the secondary crack initiation sources, from which new cracks would initiate and propagate. With the propagation of the fatigue crack, the actual maximum cyclic stress would increase to the fracture stress of the left cross section and lead to the final fracture of the specimen.

  20. New high pressure die cast magnesium alloy AM-HP2 for powertrain applications

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, M.A. [Queensland Univ., Brisbane (Australia). CAST CRC]|[CSIRO Manufacturing and Materials Technology, Clayton (Australia); Zhu, S.M.; Nie, J.F. [Queensland Univ., Brisbane (Australia). CAST CRC]|[Monash Univ., Monash (Australia). Dept. of Materials Engineering

    2007-07-01

    In order to improve the benefits available through weight savings on engine emissions, magnesium alloys must gain wider acceptance in transmission and engine applications. This paper provided details of a new alloy with exceptional creep properties developed for automotive powertrain applications. The AM-HP2 alloy was developed as part of a broader research program investigating the relationship between the composition, structure and properties of magnesium rare earth (Mg-RE) based alloys and high-pressure die casting (HPDC). Cylindrical test specimens of various alloys were produced on a cold chamber HPDC machine. Tensile creep tests were then conducted under a constant load at 177 degrees C for a period of 600 hours. Microstructures of specimens were characterized using a CM20 transmission electron microscope. Results of the tests indicated that near-grain boundary microstructure was an important parameter in securing optimum elevated temperature properties. The RE element had a significant effect on the creep behaviour of the HPDC Mg-RE alloys. It was concluded that further research is needed to investigate the influence of the RE mixture in improving creep performance. 15 refs., 2 tabs., 6 figs.

  1. Microstructural effects of phosphorus on pressure die cast Al-12Si components

    Directory of Open Access Journals (Sweden)

    Suárez-Peña, B.

    2007-10-01

    Full Text Available The refinement of cuboidal silicon in eutectic Al-Si alloys by phosphorus additions used to manufacture pressure die cast components was studied. The results show that the addition of phosphorus in the form of AlFeP mother alloy before process degassing, leads to the best refinement of the size of the Si-cuboids phase, among several phosphorus additions analysed in the present research.

    Se ha estudiado el afino del silicio cuboidal en aleaciones eutécticas Al-Si por acción del fósforo, en piezas obtenidas mediante la técnica de fundición a presión. Tras la adición de fósforo en pruebas industriales, en las que dicho elemento se incorpora al baño con diversas composiciones, los mejores resultados se obtienen con la adición de la aleación madre AlFeP, previa al desgasificado industrial.

  2. Fabrication of intermetallic NiAl by self-propagating high-temperature synthesis reaction using aluminium nanopowder under high pressure

    CERN Document Server

    Dong Shu Shan; Cheng Hai Yong; Yang Hai Bin; Zou Guang Tian

    2002-01-01

    By using aluminium nanopowder prepared by wire electrical explosion, pure monophase NiAl compound with fine crystallites (<=10 mu m) and good densification (98% of the theoretical green density) was successfully fabricated by means of self-propagating high-temperature synthesis (SHS) under a high pressure of 50 MPa. Investigation shows that, due to the physical and chemical characteristics of the nanoparticles, the SHS reaction mode and mechanism are distinct from those when using conventional coarse-grained reactants. The SHS reaction process depends on the thermal conditions related to pressure and can occur at a dramatically low temperature of 308 sup o C, which cannot be expected in conventional SHS reaction. With increasing pressure, the SHS explosive ignition temperature (T sub i sub g) of forming NiAl decreases due to thermal and kinetic effects.

  3. The Influence of Pressure Die Casting Parameters on the Castability of AlSi11-SiCp Composites

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2015-03-01

    Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the castability of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of castability of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

  4. On the capacity-formula for pressure relief devices of tanks for dangerous goods; Die Kapazitaetsformel fuer Druckentlastungsvorrichtungen von Gefahrguttanks

    Energy Technology Data Exchange (ETDEWEB)

    Ludwig, J. [Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin (Germany)

    2000-09-01

    Each tank-container respectively portable tank for multimodal purposes has to be closed and fitted with safety devices (pressure relief devices). Pressure relief devices have to meet essential requirements concerning their total delivery capacity in condition of complete engulfment of the tank in fire. The total capacity of these devices should be sufficient to limit the pressure in the tank in each case to its test pressure, maximally. The total delivery capacity has to be determined by applying a formula which had been developed in the USA and taken over later on into international and national regulations on the transport of dangerous goods. The derivation of this formula will be described and evaluated with regard to given facts related to general thermodynamics and fire test results. (orig.) [German] Wesentliche Anforderung an Sicherheitseinrichtungen (Druckentlastungsvorrichtungen) fuer Tanks und Tankcontainer im multimodalen Verkehr ist, dass diese Einrichtungen im Feuerfall eine Gesamtdurchflussmenge aufweisen muessen, die zumindest einen Druckanstieg ueber den Pruefdruck hinaus verhindert. Die Ermittlung der Gesamtdurchflussmenge erfolgt nach einer in den USA entwickelten, in internationale und nationale Verkehrsvorschriften uebernommenen Zahlenwertgleichung (Kapazitaetsformel). Die Herleitung dieser Zahlenwertgleichung sowohl aus allgemein thermodynamischen als auch empirischen Gegebenheiten wird beschrieben und bewertet. (orig.)

  5. An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

    Directory of Open Access Journals (Sweden)

    J. Mutwil

    2008-10-01

    Full Text Available A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order to find the reason of this variability the fracture surface investigations (macrographs for all of samples and SEM micrographs for chosen samples have been carried out. It has been establish that in all cases a significant decrease of tensile strength was caused by presence of inclusions or porosity. In lot of cases the inclusions have a form of oxide film.

  6. Assessment of Computer Simulation Software and Process Data for High Pressure Die Casting of Magnesium

    Energy Technology Data Exchange (ETDEWEB)

    Sabau, Adrian S [ORNL; Hatfield, Edward C [ORNL; Dinwiddie, Ralph Barton [ORNL; Kuwana, Kazunori [University of Kentucky; Viti, Valerio [University of Kentucky, Lexington; Hassan, Mohamed I [University of Kentucky, Lexington; Saito, Kozo [University of Kentucky

    2007-09-01

    Computer software for the numerical simulation of solidification and mold filling is an effective design tool for cast structural automotive magnesium components. A review of commercial software capabilities and their validation procedures was conducted. Aside form the software assessment, the program addressed five main areas: lubricant degradation, lubricant application, gate atomization, and heat transfer at metal mold interfaces. A test stand for lubricant application was designed. A sensor was used for the direct measurement of heat fluxes during lubricant application and casting solidification in graphite molds. Spray experiments were conducted using pure deionized water and commercial die lubricants. The results show that the sensor can be used with confidence for measuring heat fluxes under conditions specific to the die lube application. The data on heat flux was presented in forms suitable for use in HPDC simulation software. Severe jet breakup and atomization phenomena are likely to occur due to high gate velocities in HPDC. As a result of gate atomization, droplet flow affects the mold filling pattern, air entrapment, skin formation, and ensuing defects. Warm water analogue dies were designed for obtaining experimental data on mold filling phenomena. Data on break-up jet length, break-up pattern, velocities, and droplet size distribution were obtained experimentally and was used to develop correlations for jet break-up phenomena specific to die casting gate configurations.

  7. Transmission electron microscopy observations on phase transformations during aluminium/mullite composites formation by gas pressure infiltration

    Energy Technology Data Exchange (ETDEWEB)

    Pawlyta, M., E-mail: miroslawa.pawlyta@polsl.pl [Silesian University of Technology, Institute of Engineering Materials and Biomaterials, Konarskiego 18A, 44-100 Gliwice (Poland); Tomiczek, B.; Dobrzański, L.A.; Kujawa, M. [Silesian University of Technology, Institute of Engineering Materials and Biomaterials, Konarskiego 18A, 44-100 Gliwice (Poland); Bierska-Piech, B. [Silesian Centre for Education and Interdisciplinary Research, 75 Pułku Piechoty 1A, 41-500 Chorzów (Poland)

    2016-04-15

    The porous ceramic preforms were manufactured using the powder metallurgy technique. First, the start-up material (halloysite with the addition of carbon fibres as the pore-forming agent) was slowly heated to 800 °C and then sintered at 1300 °C. Degradation of the carbon fibres enabled the open canals to form. At the end of the sintering process, the porous ceramic material consisting mainly of two phases (mullite and cristobalite) was formed, without any residual carbon content. During infiltration, the liquid metal filled the empty spaces (pores) effectively and formed the three-dimensional network of metal in the ceramic. The cristobalite was almost entirely decomposed. In the areas of its previous occurrence, there are new pores, only in the ceramic grains. The mullite, which was formed from halloysite during annealing, crystallized in the Pbam orthorhombic space group, with the (3Al{sub 2}O{sub 3}·2SiO{sub 2}) stoichiometric composition. The mullite structure does not change during the infiltration. The composite components are tightly connected. A transition zone between the ceramics and the metal, having the thickness of about 200 nm, was formed. The nanocrystalline zone, identified as γ-Al{sub 2}O{sub 3}, was formed by diffusing the product of the cristobalite decomposition into the aluminium alloy matrix. There is an additional, new phase, identified as (Mg,Si)Al{sub 2}O{sub 4} in the outer parts of the transition zone. - Highlights: • Phase changes after the infiltration of aluminium into porous mullite preforms were observed by TEM. • TEM observations confirm that during infiltration cristobalite was decomposed and the structure of mullite did not change. • Between the ceramic and the metal, a transition zone comprising a layer of γ-Al{sub 2}O{sub 3} and (Mg,Si)Al{sub 2}O{sub 4} was formed.

  8. Rapid die manufacturing - high pressure casting of low volume non ferrous metals components

    CSIR Research Space (South Africa)

    Pereira, MFV

    2006-11-01

    Full Text Available .csir.co.za Models of assembled Die Slide 12 © CSIR 2006 www.csir.co.za 3. Die manufacture, assembly and data capturing 21.521.521.525.5total 4electrode 3Fitting3Fitting3Fitting3Fitting 2Polish2Polish2Polish2Polish 7SER 3F grind3F grind...3F grind4F grind Heat trHeat trHeat tr1Heat tr Jig boreJig boreJig boreJig bore GrindingGrindingGrinding2Grinding 13.5DMLS13.5DMLS13.5DMLS2.5Milling HrsCostProcessHrsCostProcessHrsCostProcessHrsCostProcess Core 4Core 3Core 2Core 1 NB. Times...

  9. The correlation between microstructure and mechanical properties of high-pressure die-cast AM50 alloy

    International Nuclear Information System (INIS)

    Song Jie; Xiong Shoumei; Li Mei; Allison, John

    2009-01-01

    Scanning acoustic microscopy was used to characterize the micro-voids distribution for specimens in non-destructive mode. In addition, the in-situ scanning electron microscopy observation was performed during tensile deformation of high-pressure die-cast (HPDC) of AM50 alloy to obtain the mechanism of fracture induced by micro-voids. The effects of micro-voids on the mechanical properties were discussed. The results obtained from the examination suggest that fracture tends to occur at bigger micro-voids or in the cluster micro-voids area.

  10. MICRO-MATERIAL HANDLING EMPLOYING E-BEAM GENERATED TOPOGRAPHIES OF COPPER AND ALUMINIUM

    Directory of Open Access Journals (Sweden)

    S. Matope

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: This paper focuses on the employment of copper and aluminium in a micro-material handling system actuated by Van der Waals forces. Electron beam (e-beam evaporator deposited both materials on a silicon substrate at a rate of 0.6-1.2 Angstroms/second, vacuum pressure between 2x10-6 and 3x10-6mbar, and at a current less than 10mA. A Veeco NanoMan V Atomic Force Microscope with Nanoscope version 7.3 software was used to analyse the root mean square (rms surface roughnesses of the generated topographies. Rumpf-Rabinovich’s rms formula was used to determine the Van der Waals forces exerted by the surfaces. It was synthesised that an e-beam deposition of 7 minutes’ duration on both materials produced an optimum micro-material handling solution, with copper suitable for the pick-up position and aluminium for the placement position.

    AFRIKAANSE OPSOMMING: Die fokus van die artikel is op die gebruik van koper en aluminium in ‘n mikromateriaalhanteringstelsel, aangedryf deur Van der Waalskragte. ‘n Elektronstraal-verdamper plaas albei materiale op ‘n silikonbasis teen ‘n tempo van 0.6-1.2 Angstrom/sekonde, vakuumdruk tussen 2x10-6 en 3x10-6mbar, en teen ‘n stroom van minder as 10mA. ‘n Veeco NanoMan V Atomic Force mikroskoop, met Nanoscope 7.3 program-matuur is gebruik om die wortel-gemiddelde-kwadraat (wgk oppervlak ruheid van die gegenereerde topografieë te analiseer. Rumpf-Rabinovich se wgk-formule is gebruik om die Van der Waalskrage wat deur die oppervlaktes uitgeoefen word te bepaal. Dit is vasgestel dat ‘n elektronstraalafsetting van 7 minute op albei materiale die optimale materiaalhanteringoplossing bied, met koper geskik vir die optelposisie en aluminium vir die plasingsposisie.

  11. Steam Assisted Accelerated Growth of Oxide Layer on Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Yuksel, Serkan; Jellesen, Morten Stendahl

    2013-01-01

    Corrosion resistance of aluminium alloys is related to the composition and morphology of the oxide film on the surface of aluminium. In this paper we investigated the use of steam on the surface modification of aluminium to produce boehmite films. The study reveals a detailed investigation...... of the effect of vapour pressure, structure of intermetallic particles and thickness of boehmite films on the corrosion behaviour of aluminium alloys....

  12. Numerical investigation of the effect of friction conditions to increase die life

    Science.gov (United States)

    Mutlu, M. O.; Guleryuz, C. G.; Parlar, Z.

    2017-02-01

    The standard die materials in aluminium extrusion offer good mechanical properties like high tempering resistance, high strength and ductility. On the other hand, they struggle with the problem of sliding wear. As a result, there is a growing interest in using surface treatment techniques to increase the wear resistance of extrusion dies. In this study, it is aimed to observe the effects of the different friction conditions on material flow and contact pressure in extrusion process. These friction conditions can be obtained with the application of a variety of surface treatment. In this way, it is expected to decrease the friction force on the die bearing area and to increase the homogeneity of the material flow which will result in the increase of the quality of the extrudate as well as the improvement of the process economically by extending die life. For this purpose, an extrusion process is simulated with a finite element software. A die made of 1.2344 hot work tool steel-commonly used die material for aluminium extrusion process- has been modelled and Al 1100 alloy used as billet material. Various friction factor values defined on the die surface under the same process parameters and effects of changing frictional conditions on the die and the extrusion process have been discussed.

  13. On the solubility of hydrogen in the systems titanium-aluminium-hydrogen, titanium-vanadium-hydrogen and titanium-aluminium-vanadium-hydrogen in the temperature region of 800 to 1,0000C at hydrogen pressures of 0.1 to 400 mm.Hg

    International Nuclear Information System (INIS)

    Kauder, G.W.

    1973-01-01

    The hydrogen concentrations on Ti-Al, Ti-V and Ti-Al-V alloys were determined in the temperature region from 800 to 1,000 0 C and at hydrogen pressures of 0.1 to 400 mm.Hg using a gravimetric measuring process. The thus obtained results allowed the drawing of hydrogen activity slopes in the titanium rich corner of the systems titanium-hydrogen, titanium-aluminium-hydrogen, titanium-vanadium-hydrogen and such for the technical titanium alloys Ti-6Al-4V and Ti-6Al-6V. In spite of the antagonistic effects of the elements aluminium and vanadium on the stabilization of the α and β phase regions of titanium, a hydrogen-activity-increasing effect was always found in which the aluminium influence was greater than that of vanadium. Breaks occured in the hydrogen activity curves and phase boundaries, and phase regions were determined over their positions. Isothermal phase diagrams for the titanium-rich corner of the system titanium-aluminium-hydrogen at 800, 850 and 900 0 C and for the titanium-rich corner of the titanium-vanadium-hydrogen system at 900, 950 and 1,000 0 C were drawn up from the hydrogen activity curves. (orig./LH) [de

  14. Aluminium in human sweat.

    Science.gov (United States)

    Minshall, Clare; Nadal, Jodie; Exley, Christopher

    2014-01-01

    It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans. Copyright © 2013 Elsevier GmbH. All rights reserved.

  15. Generation and characterization of nano aluminium powder ...

    Indian Academy of Sciences (India)

    TECS

    Generation and characterization of nano aluminium powder obtained through wire ... Department of Aerospace Engineering, Indian Institute of Technology. Madras, Chennai 600 .... pressure developed due to current flow (z-Pinch). Figure 2.

  16. An experimental study on joining of severe plastic deformed aluminium materials with friction welding method

    Energy Technology Data Exchange (ETDEWEB)

    Sahin, Mumin [Mechanical Engineering Department, Trakya University, 22030 Edirne (Turkey)], E-mail: mumins@trakya.edu.tr; Erol Akata, H.; Ozel, Kaan [Mechanical Engineering Department, Trakya University, 22030 Edirne (Turkey)

    2008-07-01

    In this study, 5083 aluminium alloys, which were exposed to severe plastic deformation, were joined with friction welding method and the variation in mechanical properties of the joints was experimentally investigated. Severe plastic deformation methods can be classified as equal channel angular pressing (ECAP) (in other words, equal cross section lateral extrusion - ECSLE) and cyclic extrusion-compression. Aluminium alloy as test material 5083 and square cross-sectional equal channel angular pressing die for severe plastic deformation were used in the study. Firstly 5083 alloys, as purchased, were joined with friction welding method. The optimum parameters for friction time, upset time, friction pressure and upset pressure, which are necessary for welding, were obtained. Afterwards, 5083 aluminium materials as purchased were prepared as square cross-section and then 1-pass severe plastic deformation was applied to specimen by equal channel angular pressing die. The obtained parts as square form were prepared as cylindrical form by machining and then the parts were joined by continuous drive friction welding equipment that was designed and produced in laboratory conditions before. Later, the tensile strengths of the parts, obtained at optimum conditions, were compared with those of the joined parts as purchased form. Then, hardness variations and microstructures of joints were examined. Finally, the obtained results were commented on.

  17. REDUCING REJECTION/REWORK IN PRESSURE DIE CASTING PROCESS BY APPLICATION OF DMAIC METHODOLOGY OF SIX SIGMA

    Directory of Open Access Journals (Sweden)

    Javedhusen Malek

    2015-12-01

    Full Text Available In today's ever-changing customer driven market, industries are needed to improve their products and processes to satisfy customer requirements. The Six Sigma approach has set a new paradigm of business excellence. Six Sigma as a process driven improvement methodology has been adopted successfully by many industries. From the review of various literatures, it is revealed that Six Sigma is well adopted in large scale enterprise but having less evidence of adoption in Indian SMEs. This paper is focused on providing path to Indian SMEs for initiating Six Sigma approach in their industries. The paper discusses the real life case where Six Sigma has been successfully applied at one of the Indian small-scale unit to improve rejection/rework rate in manufacturing products by pressure die casting process. This paper describes phase wise application of all the phases of define-measure-analyse-improve-control (DMAIC which also shows impact of Six Sigma in quality improvement.

  18. Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Wei; Zhang, Jinghuai; Li, Guoqiang; Feng, Yan; Su, Minliang; Wu, Ruizhi; Zhang, Zhongwu [Harbin Engineering Univ. (China). Key Laboratory of Superlight Material and Surface Technology; Jiao, Yufeng [Jiamusi Univ. (China). College of Materials Science and Engineering

    2017-05-15

    The thermal stability of Al-RE (rare earth) intermetallic phases with individual RE for heat-resistant high-pressure die-casting Mg-Al-RE alloys is investigated. The results of this study show that the main strengthening phase of Mg-4Al-4Ce alloy is Al{sub 11}Ce{sub 3}, whose content is about 5 wt.% according to quantitative X-ray diffraction phase analysis. The Al{sub 11}Ce{sub 3} phase appears to have high thermal stability at 200 C and 300 C, while phase morphology change with no phase structure transition could occur for Al{sub 11}Ce{sub 3} when the temperature reaches 400 C. Furthermore, besides the kinds of rare earths and temperature, stress is also an influencing factor in the microstructural stability of Mg-4Al-4Ce alloy.

  19. die rol van die unieverdedigingsmag in die onderdrukking van die

    African Journals Online (AJOL)

    agv regeringsoptrede nie.39. Siotsom. In die geskiedenis van die Unieverdedigings- mag word die gebeure random die 1914-staking oorskadu deur die Rebellie en Suid-Afrika se deelname aan die Eerste Wereldoorlog. Tog was dit 'n belangrike mylpaal in die geskiedenis van die organisasie, omdat dit sy eerste optrede ...

  20. Human exposure to aluminium.

    Science.gov (United States)

    Exley, Christopher

    2013-10-01

    Human activities have circumvented the efficient geochemical cycling of aluminium within the lithosphere and therewith opened a door, which was previously only ajar, onto the biotic cycle to instigate and promote the accumulation of aluminium in biota and especially humans. Neither these relatively recent activities nor the entry of aluminium into the living cycle are showing any signs of abating and it is thus now imperative that we understand as fully as possible how humans are exposed to aluminium and the future consequences of a burgeoning exposure and body burden. The aluminium age is upon us and there is now an urgent need to understand how to live safely and effectively with aluminium.

  1. Characteristics of pressure gradients in downflow condensing of nitrogen in plain, brazed aluminium, plate-fin heat exchanger passages

    International Nuclear Information System (INIS)

    Robertson, J.M.; Blundell, N.; Clarke, R.H.

    1987-01-01

    Measurements of the total two-phase gradients have been made during the downflow condensing of nitrogen in a vertical plain, plate-fin test-section. The results show that pressure recovery occurs only at very low qualities, at low mass flux the falling film is smooth and at high mass flux it is rough. A relationship between the apparent film roughness and the calculated film thickness has been established. The implications for designers of heat exchangers are discussed

  2. Wear behavior of carbon fiber/aluminium-composites during abrasive loading; Verschleissverhalten von Kohlenstoffaser/Aluminium-Verbunden unter abrasiver Beanspruchung

    Energy Technology Data Exchange (ETDEWEB)

    Wielage, B.; Dorner, A. [Technische Univ. Chemnitz (Germany). Lehrstuhl fuer Verbundwerkstoffe

    1998-07-01

    Abrasive wear resistance of aluminium is significantly improved by the reinforcement with a high volume percentage of carbon fibres. The wear of unreinforced aluminium after scratching by a diamond indenter can be described as pure microgrooving without any micro-chipping. After integration of 70 vol.-% carbon fibers the damage mechanism is considerably altered and a great amount of micro-chipping occurs. The abrasive wear is strongly influenced by the fiber orientation. The best wear resistance is observed when the fibers are orientated perpendicular to the wear surface. (orig.) [Deutsch] Die Verstaerkung von Aluminium mit einem hohen Volumengehalt endloser Kohlenstoffasern verbessert erkennbar dessen Resistenz gegenueber Abrasionsverschleiss. Der Verschleiss von unverstaerktem Aluminium infolge des Ritzens mit einem Diamantindenter erfolgt in Form von reinem Mikrofurchen ohne Spanbildung. Aufgrund der Integration von 70 Vol.-% Kohlenstoffasern wird eine erhebliche Zunahme des Schaedigungsmechanismus Mikrospanen festgestellt. Die Faserorientierung hat merklichen Einfluss auf die Sensibilitaet gegenueber Abrasion. Orientierung der anisotropen Kohlenstoffasern senkrecht zur Verschleissoberflaeche bedingt den geringsten Abrasionsverschleiss. (orig.)

  3. Microstructure and mechanical properties of AM50 alloy according to thickness and forming condition of the products by a high pressure die-casting process

    Energy Technology Data Exchange (ETDEWEB)

    Park, Joon Hong [Dong-A University, Busan (Korea, Republic of); Kang, Chung Gil [Pusan National University, Busan (Korea, Republic of)

    2013-10-15

    In recent years, Magnesium (Mg) and its alloys have become a center of special interest in the automotive industry. Due to their high specific mechanical properties, they offer a significant weight saving potential in modern vehicle constructions. Most Mg alloys show very good machinability and processability, and even the most complicated die casting parts can be easily produced. The die casting process is a fast production method capable of a high degree of automation for which certain Mg alloys are ideally suited. Although Mg alloys are fulfilling the demands for low specific weight materials with excellent machining and casting abilities, they are still not used in die casting process to the same extent as the competing material aluminum. One of the reasons is that effects of various forming variables for die casting process is not closely examined from the viewpoint of die design. In this study, step die and flowability tests for AM50 were performed by die casting process according to various combination of casting pressure and plunger velocity. Microstructure, Vickers hardness and tensile tests were examined and performed for each specimen to verify effects of forming conditions.

  4. Contact Behavior of Composite CrTiSiN Coated Dies in Compressing of Mg Alloy Sheets under High Pressure

    Directory of Open Access Journals (Sweden)

    T.S. Yang

    2018-01-01

    Full Text Available Hard coatings have been adopted in cutting and forming applications for nearly two decades. The major purpose of using hard coatings is to reduce the friction coefficient between contact surfaces, to increase strength, toughness and anti-wear performance of working tools and molds, and then to obtain a smooth work surface and an increase in service life of tools and molds. In this report, we deposited a composite CrTiSiN hard coating, and a traditional single-layered TiAlN coating as a reference. Then, the coatings were comparatively studied by a series of tests. A field emission SEM was used to characterize the microstructure. Hardness was measured using a nano-indentation tester. Adhesion of coatings was evaluated using a Rockwell C hardness indentation tester. A pin-on-disk wear tester with WC balls as sliding counterparts was used to determine the wear properties. A self-designed compression and friction tester, by combining a Universal Testing Machine and a wear tester, was used to evaluate the contact behavior of composite CrTiSiN coated dies in compressing of Mg alloy sheets under high pressure. The results indicated that the hardness of composite CrTiSiN coating was lower than that of the TiAlN coating. However, the CrTiSiN coating showed better anti-wear performance. The CrTiSiN coated dies achieved smooth surfaces on the Mg alloy sheet in the compressing test and lower friction coefficient in the friction test, as compared with the TiAlN coating.

  5. Contact Behavior of Composite CrTiSiN Coated Dies in Compressing of Mg Alloy Sheets under High Pressure.

    Science.gov (United States)

    Yang, T S; Yao, S H; Chang, Y Y; Deng, J H

    2018-01-08

    Hard coatings have been adopted in cutting and forming applications for nearly two decades. The major purpose of using hard coatings is to reduce the friction coefficient between contact surfaces, to increase strength, toughness and anti-wear performance of working tools and molds, and then to obtain a smooth work surface and an increase in service life of tools and molds. In this report, we deposited a composite CrTiSiN hard coating, and a traditional single-layered TiAlN coating as a reference. Then, the coatings were comparatively studied by a series of tests. A field emission SEM was used to characterize the microstructure. Hardness was measured using a nano-indentation tester. Adhesion of coatings was evaluated using a Rockwell C hardness indentation tester. A pin-on-disk wear tester with WC balls as sliding counterparts was used to determine the wear properties. A self-designed compression and friction tester, by combining a Universal Testing Machine and a wear tester, was used to evaluate the contact behavior of composite CrTiSiN coated dies in compressing of Mg alloy sheets under high pressure. The results indicated that the hardness of composite CrTiSiN coating was lower than that of the TiAlN coating. However, the CrTiSiN coating showed better anti-wear performance. The CrTiSiN coated dies achieved smooth surfaces on the Mg alloy sheet in the compressing test and lower friction coefficient in the friction test, as compared with the TiAlN coating.

  6. Aluminium EN AW-2124 alloy matrix composites reinforced with Ti(C,N), BN and Al2O3 particles

    International Nuclear Information System (INIS)

    Dobrzanski, L.A.; Wlodarczyk, A.; Adamiak, M.

    2003-01-01

    Investigation results of the aluminium alloy EN AW-2124 matrix composite materials with particles of the powders Ti(C,N), BN and Al 2 O 3 (15 wt.%) are presented in the paper. In order to obtain uniform distribution of reinforcement particles in aluminium alloy matrix powders of composite components have been milled in the rotary ball-bearing pulverizer. The composites have been pressed in laboratory vertical press at room temperature under the pressure of 500 kN. Obtained die samplings have been heated to the temperature 520-550 o C and extruded. Bars of diameter 8 mm have been received as a final product. Metallographic examination of the composites materials' structure shows non-uniform distribution of reinforced powders in the aluminium alloy matrix banding of reinforcements particles corresponds to the extrusion direction. Particles of reinforcement distribution in aluminium alloy matrix is irregular, some agglomerations of powder of aluminium oxide and porosity of different size have been noticed. Investigations of hardness and ultimate compressive strength show that the particles of reinforcement improve mechanical properties of composite materials. Investigations of compressive strength, carried out at room temperature, enable to compare mechanical properties of matrix and composite. (author)

  7. Die binding van die konfessie

    Directory of Open Access Journals (Sweden)

    P. J. Coetzee

    1970-05-01

    Full Text Available Ons moet waak teen twee uiterstes. Aan die een kant het die dogma as onversoenlike vyand die dogmatisme en aan die ander kant die antidogmatisme — dit hou enersyds die gevaar in van verabsolutering (oorskatting, en ander- syds die gevaar van relativisme (onderskatting.

  8. Die Region braucht die Kultur - die Kultur braucht die Region

    OpenAIRE

    Klemm, Ulrich

    1995-01-01

    Die Region braucht die Kultur - die Kultur braucht die Region. - In: Region in Aktion - oder: Region im Abseits? - Boxberg-Wölchingen : Eigenständige Regionalentwicklung Baden-Württemberg, 1995. - S. 25 f.

  9. Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting.

    Science.gov (United States)

    Wang, J; Guo, Z; Song, J L; Hu, W X; Li, J C; Xiong, S M

    2017-11-03

    The microstructure of a high-pressure die-cast hypereutectic A390 alloy, including PSPs, pores, α-Al grains and Cu-rich phases, was characterized using synchrotron X-ray tomography, together with SEM, TEM and EBSD. The Cu-rich phases exhibited a net morphology and distributed at the boundaries of the α-Al grains, which in turn surrounded the PSPs. Statistical analysis of the reconstructed 1000 PSPs showed that both equivalent diameter and shape factor of the PSPs exhibited a unimodal distribution with peaks corresponding to 25 μm and 0.78, respectively.) PSPs morphology with multiple twinning were observed and morphological or growth transition of the PSPs from regular octahedral shape (with a shape factor of 0.85 was mainly caused by the constraint of the Cu-rich phases. In particular, the presence of the Cu-rich phases restricted the growth of the α-Al grains, inducing stress on the internal silicon particles, which caused multiple twinning occurrence with higher growth potential and consequently led to growth transitions of the PSPs.

  10. Implications of the Pressurized Equipment Directive of the EC for the German gas trade and industry; Die Bedeutung der EG-Druckgeraeterichtlinie fuer das deutsche Gasfach

    Energy Technology Data Exchange (ETDEWEB)

    Jannemann, T.B. [DVGW Deutsche Vereinigung des Gas- und Wasserfaches e.V., Bonn (Germany)

    2003-06-01

    The standards and requirements to be met by the equipment, components and materials manufactured and used in Germany are specified in the DVGW code, of which some parts and content will need amending and adjustment to the EC Pressurized Equipment Directive. The aim of this harmonization is to remove technical barriers to trade within the European Union. (orig./CB) [German] Die konkreten Anforderungen an Geraete, Bauteile und Materialien sind im DVGW-Regelwerk festgeschrieben. Im Rahmen der Realisierung des EU-Binnenmarktes wird das DVGW-Regelwerk teilweise europaeisch harmonisiert. Ziel ist die Beseitigung technischer Handelshemmnisse unter gleichzeitiger Beruecksichtigung des europaeisch relevanten Schutzniveaus. (orig.)

  11. The Influence of Pressure Die Casting Parameters on the Mechanical Properties of AlSi11/10 Vol.% SiC Composite

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2014-03-01

    Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the tensile strength, the yield point, the elongation and hardness of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of mechanical properties of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

  12. The Influence of Pressure Die Casting Parameters on Distribution of Reinforcing Particles in the AlSi11/10% SiC Composite

    Directory of Open Access Journals (Sweden)

    Pasieka A.

    2013-09-01

    Full Text Available The method of pressure die casting of composites with AlSi11 alloy matrix reinforced with 10 vol. % of SiC particles and the analysis of the distribution of particles within the matrix is presented. The composite castings were produced at various values of the piston velocity in the second stage of injection, at diverse intensification pressure values, and various injection gate width values. The distribution of particles over the entire cross-section of the tensile specimen is shown. The index of distribution was determined on the basis of particle count in elementary measuring fields. The regression equation describing the change of the considered index was found as a function of the pressure die casting parameters. The conclusion presents an analysis of the obtained results and their interpretation.

  13. Die nabyheid van die Koninkryk

    Directory of Open Access Journals (Sweden)

    W.J. Snyman

    1963-03-01

    Full Text Available Vanweë die belangrikheid daarvan volg hier ’n breër bespreking van die proefskrif van dr. Tjaart van der Walt oor die nabyheid van die Koninkryk as wat in ’n gewone resensie kan geskied. Die vraagstuk wat onder oë gesien word is so oud as die kerk en die teologie, soms minder en soms meer op die voorgrond. Tans kan gesê word, staan dit in die middelpunt. Daarby is dit nie maar ’n akademiese vraagstuk nie, maar ’n vraagstuk waarvoor elke nadenkende leser van die Skrif te staan kom.

  14. The counter pressure Pelton turbine as a solution to the energy production in drinking water systems; Die Gegendruck-Peltonturbine als Loesung fuer die Energieproduktion in Trinkwassersystemen

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, Reto [Haeny AG - Pumpen, Turbinen und Systeme, Jona (Switzerland); Juric, Thomas [A. Abel GmbH, Pumpen und Turbinen, Wundschuh (Austria)

    2010-07-01

    In drinking water slumbers green electricity. Up to now classical Pelton turbines or cheaper standard pumps running in reverse (PAT) were used. Both technologies have disadvantages or limitations regarding their possible applications, therefore, the optimal implementation of the existing potentials are often not entirely possible. The new ''Counter pressure Pelton turbine'' combines the advantages of both technologies and is therefore in many cases the ''most efficient solution''. (orig.)

  15. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  16. Die topkwark

    Directory of Open Access Journals (Sweden)

    R. Tegen

    1998-07-01

    Full Text Available ’n Oorsig van die belangrikheid van die onlangs ontdekte topkwark by Fermilab in Chicago word gegee. Daar word aangetnon dat die topkwark belangrik is in fisika van die Oerknal, oftewel "Big Bang", en in die Standaard Model van Elementêredeeltjie-fisika. Toepaslike literatuur vir verdere studie kan van die lys van verwysings in hierdie kort, nietegniese artikel, nagegaan word.

  17. Study of the combustion of aluminium and magnesium particulates: influence of the composition of the gaseous mixture and of pressure; Etude de la combustion de particules d'aluminium et de magnesium: influence de la composition du melange gazeux et de la pression

    Energy Technology Data Exchange (ETDEWEB)

    Legrand, B.

    2000-07-01

    The combustion of metal particulates has a major interest in the domain of space propulsion. Aluminium is today used as doping material in the solid propellant of Ariane 5 rocket engines. Magnesium represents a possible fuel for propellers allowing a come back from Mars. An electrostatic levitation device has been used to study the combustion in controlled environment of particulates having a size representative of those encountered in propellers. The particulates are ignited with a laser and observed by fast cinematography. The inhibitive property of hydrogen chloride, an important constituent of the propellant atmosphere, on the combustion of aluminium particulates has been evidenced. These results have been compared with those obtained with a kinetic model in gaseous phase. The combustion of magnesium particulates in carbon dioxide has been studied for 53-63 {mu}m and 1-2 mm particulates. It is shown that the ignition of small particulates is controlled by the chemical kinetics and that the limit ignition pressure is reversely proportional to the particulates size. A study on big samples, performed in normal gravity but also in reduced gravity to get rid of the natural convection phenomena, has permitted to show a pulsed combustion regime linked with the presence of heterogenous reactions. The measurement of the combustion durations for the different sizes of particulates has permitted to propose a correlation between these two parameters for the particulate diameters comprised between 50 {mu}m and 2 mm. (J.S.)

  18. Aluminium in Infrastructures

    NARCIS (Netherlands)

    Maljaars, J.

    2016-01-01

    Aluminium alloys are used in infrastructures such as pedestrian bridges or parts of it such as handrail. This paper demonstrates that aluminium alloys are in principle also suited for heavy loaded structures, such as decks of traffic bridges and helicopter landing platforms. Recent developments in

  19. Aluminium beverage can recycling

    Energy Technology Data Exchange (ETDEWEB)

    Lewinski, A von

    1985-08-01

    Canned beverages have become a controversial issue in this era of ecological sensitivity. METALL has already discussed the problem of can recycling. The present article discusses the technical aspects of aluminium can recycling. Two further articles will follow on aluminium can recycling in North America and on the results of European pilot projects.

  20. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

  1. Continuum damage mechanics based approach to the fatigue life prediction of cast aluminium alloy with considering the effect of porosity

    Directory of Open Access Journals (Sweden)

    Wang Xiaojia

    2018-01-01

    Full Text Available A damage mechanics based approach is applied for the study of fatigue behaviour of high pressure die cast ADC12 aluminium alloy. A damage coupled elastoplastic constitutive model is presented according to the concept of effective stress and the hypothesis of strain equivalence. An elastic fatigue damage model taking into account the pore-induced stress concentration is developed to investigate fatigue damage evolution of the specimens subjected to cyclic loading. The predicted lives for the specimens with different sizes of pores are consistent with the experimental data. The pore-induced fatigue damage and the variation of fatigue life along with the size of pores are also investigated.

  2. Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method

    International Nuclear Information System (INIS)

    Senthil, P.; Amirthagadeswaran, K. S.

    2012-01-01

    This paper reports a research in which an attempt was made to prepare AC2A aluminium alloy castings of a non symmetrical component through squeeze casting process. The primary objective was to investigate the influence of process parameters on mechanical properties of the castings. Experiments were conducted based on orthogonal array suggested in Taguchi's offline quality control concept. The experimental results showed that squeeze pressure, die preheating temperature and compression holding time were the parameters making significant improvement in mechanical properties. The optimal squeeze casting condition was found and mathematical models were also developed for the process

  3. Recovery in aluminium

    DEFF Research Database (Denmark)

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

  4. Correlations Between Arrangement of Reinforcing Particles and Mechanical Properties in Pressure Die Cast AlSi11-SiC Composites

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2014-06-01

    Full Text Available The work presents the investigation results concerning the structure of composite pressure die castings with AlSi11 alloy matrix reinforced with SiC particles. Examination has been held for composites containing 10 and 20 volume percent of SiC particles. The arrangement of the reinforcing particles within the matrix has been qualitatively assessed in specimens cut out of the castings. The index of distribution was determined on the basis of particle count in elementary measuring fields. The tensile strength, the yield point and elongation of the obtained composite were measured. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. The regression equation describing the change of the considered arrangement particles index and mechanical properties were found as a function of the pressure die casting parameters. The infuence of particle arrangement in composite matrix on mechanical properties these material was examined and the functions of correlations between values were obtained. The conclusion gives the analysis and the interpretation of the obtained results.

  5. The variable contact pressure influence on the tensile force in the process of strip sliding in the flat die in ironing

    Directory of Open Access Journals (Sweden)

    Milan Djordjević

    2016-07-01

    Full Text Available Possibilities to influence the deep drawing process during its duration are limited and generally consist of influences at the flange of the thin sheet, mainly by the contact pressure (the blank holding force. The common characteristics of previous investigations were setting of the fixed values of the blank holding force or the holder's pressure within the ironing tool. The objective of this investigation was the continuous setting of the variable pressure during the sliding process, via the preset functions, in order to analyze the variable pressure influence on the ironing process. This is why an experimental computerized device was designed and constructed for analyzing the influence of the variable contact pressure on the sliding process of the model strip during the flat-die test. The multi-parameter experiment was conducted; various materials of the tested pieces were applied (primarily thin sheet made of Al alloys and low-carbon steels sheet, with and without coating; different versions of the tool's contact elements were used, with various friction regimes and influential parameters (variable contact pressure during the sliding process, etc.. This experimental device practically represents a simulator for realization and studying of the physical model of an important segment of the ironing process in the completely realistic conditions (materials, tools, etc.. The aim was to find the optimal combination of the variable contact pressure and the tribological parameters, so that the punch force, as one of the process output parameters, would have the minimal value, as well as to avoid the undesired effects during the forming (difficult sliding of the flange, appearance of thin sheet's wrinkling, structural destruction, etc.. Understanding the mutual dependence of the holder's variable pressure and other influences should enable improvement of the ironing process control and should contribute to better understanding of the phenomena

  6. Die funksie van die belydenis in die struktuur van die kerk en die ...

    African Journals Online (AJOL)

    Ter wille van die argument wat in hierdie voordrag na vore gebring word, word vier sodanige konstituerende elemente van die kerklike struktuur onderskei, te wete die belydenis, die teologie, die verkondi- ging (meer bepaald die prediking) en die kerkorde (kerkwet volgens ons terminologie). Ons gaan nou elkeen hiervan ...

  7. Die posisie van die Helper in die sending

    Directory of Open Access Journals (Sweden)

    I. J. van der Walt

    1972-05-01

    Full Text Available Gedurende die aanvangsjare van die sending het die helper ’n onmisbare funksie vervul. Hulle het die onherbergsame binnelande geken, waardevolle kontakpunte vir die sendelinge geopen en hulle mense geestelik help voorlig en voorberei.

  8. Ion nitriding of aluminium

    International Nuclear Information System (INIS)

    Fitz, T.

    2002-09-01

    The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma immersion ion implantation, which are methods with a potential for industrial application. (orig.)

  9. Raw materials for aluminium production

    International Nuclear Information System (INIS)

    Galushkin, N.V.

    1995-01-01

    This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.

  10. Fatal aluminium phosphide poisoning

    Directory of Open Access Journals (Sweden)

    Meena Mahesh Chand

    2015-06-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

  11. Constructions of aluminium electrolytic cells

    International Nuclear Information System (INIS)

    Galushkin, N.V.

    1995-01-01

    This chapter of monograph is devoted to constructions of aluminium electrolytic cells. Therefore, the general characteristic and classification of aluminium electrolytic cells was considered. The anode and cathode structure was studied. The lining of cathode casing, the process of collection of anode gases, electrolytic cell cover, and electrical insulation was studied as well. The installation and dismantling of aluminium electrolytic cells was described.

  12. Photochemical preparation of aluminium oxide layers via vacuum ultraviolet irradiation of a polymeric hexanoato aluminium complex

    International Nuclear Information System (INIS)

    Wennrich, L.; Khalil, H.; Bundesmann, C.; Decker, U.; Gerlach, J.W.; Helmstedt, U.; Manova, D.; Naumov, S.; Prager, L.

    2013-01-01

    By means of photochemical conversion of thin layers of a polymeric hexanoato aluminium complex as the precursor, thin aluminium oxide layers were prepared onto silicon wafers. The precursor compound was synthesized and characterized by several analytical techniques like NMR, FTIR, XPS, ICP, and found to be a polymeric aluminium-containing coordination compound which has been proposed to be a hydroxo-bridged aluminium chain with pendant hexanoyl side-chains ascertained as catena-poly[{di(κ-O,O-hexanoato)aluminium}(μ-hydroxo)] (PHAH). Thin layers deposited from a solution of PHAH in toluene onto silicon wafers were irradiated using VUV radiation from a xenon excimer lamp. The layers were characterized by XPS, XRD, XRR, and spectroscopic ellipsometry. VUV radiation with a radiant exposure of E = 36 J cm −2 led to almost carbon-free amorphous layers with a composition close to that of alumina having a density of about 2.1 g cm −3 . Thus, using the example of a polymeric aluminium complex, the potential of the photochemical conversion of metal complexes into oxides could be shown as an alternative method, in addition to sol–gel techniques, for the generation of thin plane metal-oxide layers at normal temperature and pressure. Highlights: ► A polymeric aluminium complex was synthesized and characterized by NMR, FTIR, XPS and ICP. ► Thin layers of the compound were irradiated using vacuum-UV radiation and converted to AlO x . ► Quantum-chemical calculations explain the conversion mechanism.

  13. DIE GESKIEDENIS VAN DIE PERSONEELFUNKSIE IN DIE SA ...

    African Journals Online (AJOL)

    stel (kortdiensstelsel). Met die uitbreek van die oorlog in 1939 het die. Unieverdedigingsmag uit 40% Staandemag en. 60% aktiewe Burgermag bestaan. Op 22 Sept. 1939 is magtiging aan die Aktiewe Burgermag- eenhede verleen om vrywilligers vir die duur van die oorlog te aanvaar. Agv beswaar dat die Verdedigingswet.

  14. Die Formatestadt

    OpenAIRE

    Günter Trojan

    2013-01-01

    Zu Zeiten von DV oder VHS (wer kennt das eigentlich noch?) war die Welt noch in Ordnung: Da hatte man eine Kassette in der Hand und wenn das passende Gerät gefunden wurde konnte man das Video auch abspielen. Günter Trojan diskutiert die Geschichte und Gegenwart unterschiedlicher Videoformate ...

  15. Die Formatestadt

    Directory of Open Access Journals (Sweden)

    Günter Trojan

    2013-06-01

    Full Text Available Zu Zeiten von DV oder VHS (wer kennt das eigentlich noch? war die Welt noch in Ordnung: Da hatte man eine Kassette in der Hand und wenn das passende Gerät gefunden wurde konnte man das Video auch abspielen. Günter Trojan diskutiert die Geschichte und Gegenwart unterschiedlicher Videoformate ...

  16. Effect of parameters of high-pressure die casting on occurrence of casting nonconformities in sleeves of silumin alloy EN AB 47100

    Directory of Open Access Journals (Sweden)

    Pałyga Ł.

    2017-03-01

    Full Text Available The paper presents a research on the effect of extreme - for the technology of the considered silumin EN AB 47100 - parameters of high-pressure die casting on occurrence of casting nonconformities. Considered was influence of the way of assembling the mould cooled-down to 140-160°C, non-standard for the selected casting, and pouring temperature in the range of 705 to 720°C (higher than the recommended of non-refined alloy. The castings were prepared with use of a high-pressure casting machine made by Kirov with mould closing force of 2500 kN. Occurrence of nonconformities was evaluated on properly prepared specimens taken from the castings manufactured with various parameters of the injection piston and various multiplication pressures. The results were subjected to quantitative and qualitative analyses of casting nonconformities and distribution of major alloying elements. It was found that proper selection of working parameters of the casting machine, in spite of disadvantageous pouring conditions, makes it possible to reduce occurrence of some casting defects, like shrinkage cavities and porosity, to improve tightness of castings even when the alloy refining process is omitted.

  17. Accelerated growth of oxide film on aluminium alloys under steam: Part I: Effects of alloy chemistry and steam vapour pressure on microstructure

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Gudla, Visweswara C.; Jellesen, Morten S.

    2015-01-01

    of the oxide layeras well as the compactness increased with steam vapour pressure. The increase in vapour pressure also resulted in a better coverage over the intermetallic particles. Oxide layer showed a layered structure with more compact layer at the Al interface and a nano-scale needle like structure...

  18. Development of accurate dimethyl sulphide primary standard gas mixtures at low nanomole per mole levels in high-pressure aluminium cylinders for ambient measurements

    Science.gov (United States)

    Eon Kim, Mi; Kang, Ji Hwan; Doo Kim, Yong; Lee, Dong Soo; Lee, Sangil

    2018-04-01

    Dimethyl sulphide (DMS) plays an important role in atmospheric chemistry and climate change. Ambient DMS is monitored in a global network and reported at sub-nanomole per mole (nmol/mol) levels. Developing traceable, accurate DMS standards at ambient levels is essential for tracking the long-term trends and understanding the role of DMS in the atmosphere. Gravimetrically prepared gas standards in cylinders are widely used for calibrating instruments. Therefore, a stable primary standard gas mixture (PSM) is required for traceable ambient DMS measurement at remote sites. In this study, to evaluate adsorption loss on the internal surface of the gas cylinder, 6 nmol mol-1 DMS gas mixtures were prepared in three types of aluminium cylinders: a cylinder without a special coating on its internal surface (AL), an Aculife IV  +  III-treated cylinder (AC), and an Experis-treated cylinder (EX). There was little adsorption loss on the EX cylinder, whereas there was substantial adsorption loss on the other two cylinders. The EX cylinder was used to prepare 0.5, 2, 5, and 7 nmol mol-1 DMS PSMs with relative expanded uncertainties of less than 0.4%. The DMS PSMs were analytically verified and consistent within a relative expanded uncertainty of less than 1.2%. The long-term stability of the 7 nmol mol-1 DMS PSM was assessed by tracking the ratio of the DMS to the internal standard, benzene. The results showed that the DMS was stable for about seven months and it was projected to be stable for more than 60 months within a relative expanded uncertainty of 3%.

  19. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.E.J.; Soetens, F.

    2005-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical

  20. Activation Analysis of Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Brune, Dag

    1961-01-15

    An analysis of pure aluminium alloyed with magnesium was per- formed by means of gamma spectrometry , Chemical separations were not employed. The isotopes to be determined were obtained in conditions of optimum activity by suitably choosing the time of irradiation and decay. The following elements were detected and measured quantitatively: Iron, zinc, copper, gallium, manganese, chromium, scandium and hafnium.

  1. Sintered aluminium powders

    International Nuclear Information System (INIS)

    Stepanova, M.G.; Matveev, B.I.

    1974-01-01

    The mechanical and physical properties of aluminium powder alloys and the various methods employed to produce them are considered. Data are given on the hardening of the alloys SAP and SPAK-4, as well as the powder-alloy system Al-Cr-Zr. (L.M.)

  2. Indentation of aluminium foam at low velocity

    Directory of Open Access Journals (Sweden)

    Shi Xiaopeng

    2015-01-01

    Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

  3. Deposition of aluminium nanoparticles using dense plasma focus device

    International Nuclear Information System (INIS)

    Devi, Naorem Bilasini; Srivastava, M P; Roy, Savita

    2010-01-01

    Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

  4. Die funksie van die skeppingstradisie in die boek Jeremia

    African Journals Online (AJOL)

    gedeeites voor wat sterk ooreenkomste toon met die beskrywings van die skep pingsgebeure in die boek Jeremia. • Volgpns Von Rad (1957:144-146) het daar wel 'n groep bestaan wat belange ge- had liet by die oorlewering van die skeppingstradisies. Dit was waarskynlik die. Sadokitiese priesters wat om twee redes aan ...

  5. Die regsposisie van die gemolesteerde kind 1

    Directory of Open Access Journals (Sweden)

    P.J. Schabort

    1991-03-01

    Full Text Available Hoe reik die reg uit na die seksueel gemolesteerde kind? As na die reg in wye verband gekyk word, sou dit alie wetgewing en alle gemeneregsbeginsels en alle regsprosedures insluit waardeur die Staat poog om molestering te voorkom en die gemolesteerde kind in beskerming te neem. Dit le baie wyd en sou byvoorbeeld die maatreels insluit van die Kindenvet 33 van 1960; die Wet op Egskeiding 70 van 1979; die Wet op Kindersorg 74 van 1983; die Wet op die Status van Kinders 82 van 1987 en die Wet op Bemiddeling in Sekere Egskeidingsaangeleenthede 24 van 1987. Eersdaags sal dit moontlik ook ’n Manifes vir die Regte van Kinders insluit wat vermoedelik geskoei sal wees op die W O se Konvensie vir die Regte van die Kind (1989 w a arv an die RSA tan s nog nie ’n ondertekenaar is nie.

  6. Laser welding of aluminium alloys

    OpenAIRE

    Forsman, Tomas

    2000-01-01

    This thesis treats laser welding of aluminium alloys from a practical perspective with elements of mathematical analysis. The theoretical work has in all cases been verified experimentally. The aluminium alloys studied are from the 5xxx and 6xxx groups which are common for example in the automotive industry. Aluminium has many unique physical properties. The properties which more than others have been shown to influence the welding process is its high reflection, high thermal conductivity, lo...

  7. Chapter 1. Economic aspects of aluminium production

    International Nuclear Information System (INIS)

    Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

    2011-01-01

    This article is devoted to economic aspects of aluminium production. Therefore, the perspectives of development of aluminium production, the base components of aluminium cost and economic security of enterprise are considered in this chapter.

  8. Roll bonding of strained aluminium

    DEFF Research Database (Denmark)

    Staun, Jakob M.

    2003-01-01

    This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

  9. Comparison between 0.5% timolol maleate and 0.2% brimonidine tartrate in controlling increase in intraocular pressure after neodymium: yttrium-aluminium-garnet laser capsulotomy

    International Nuclear Information System (INIS)

    Tayyab, H.; Azhar, M.N.; Haider, M.A.; Jahangir, T.

    2013-01-01

    Objective: To compare the effectiveness of prophylactically given 0.5% Timolol maleate and 0.2% Brimonidine tartrate in controlling increase in intraocular pressure after neodymium (Nd) : yttrium aluminum garnet (YAG) laser capsulotomy. Study Design: Randomized controlled trial. Place and Duration of Study: This study was conducted at Ophthalmology Department, Jinnah Hospital, Lahore from 15-05-2009 to 14-05-2010 for a duration of 12 months. Material and Methods: In this study, 90 consecutive patients were referred from outpatient department for Nd: YAG laser capsulotomy. Hospital ethical committee's approval for this research proposal and the informed consent was taken. These patients were equally divided into two groups A and B, comprising of 45 patients in each group. Group A was control group which received 0.5% Timolol maleate. Group B was experimental group which received 0.2% Brimonidine tartrate. Intraocular pressure was measured using Goldmann tonometer before instilling these topical medications. These medications were administered topically 1 hour before the laser procedure. Intraocular pressure (IOP) was recorded 1 and 3 hours after laser capsulotomy. Results: In patients belonging to group A, 42 (93.3%) patients had effective control of IOP (raise of less than or equal to 5 mmHg from the baseline) after 3 hours of Nd:YAG laser capsulotomy whereas 28 (62.2%) patients had effective control of IOP after the same period of time in group-B with significant difference (p<0.001). Conclusion: Use of prophylactic topical antiglaucoma medications before doing Nd: YAG laser capsulotomy is a effective way to reduce post laser spike of intraocular pressure. Present study showed that the use of 0.5% timolol maleate was safe and more effective than 0.2% brimonidine tartrate when given 1 hour before laser capsulotomy. (author)

  10. Laser beam welding of high strength aluminium-lithium alloys; Laserstrahlschweissen von hochfesten Aluminium-Lithium Legierungen

    Energy Technology Data Exchange (ETDEWEB)

    Enz, Josephin

    2012-07-01

    The present development in aircraft industry determined by the demand for a higher cost-effectiveness. Laser beam welding is one of the most promising joining technologies for the application in the aircraft industry through the considerable reduction of the production costs. Furthermore the weight of an aircraft structure can be reduced by the use of light and high strength aluminium alloys. This paper deals with the development of a process for the laser beam welding of a skin-stringer-joint where the Al-Li-alloy AA2196 is used as stringer material and the Al-Li-alloy AA2198 is used as skin and stringer material. By the use of design of experiments the optimal welding process parameters for different material combinations were determined which will be used for the welding of a 5-stringer panel. Therefore the weld seams of the joints were tested for irregularities and microstructural characteristics. In addition several mechanical tests were performed, which define the quality of the welded joint. Furthermore the influence of the oxide layer and the welding preparation on the welding performance was investigated. (orig.) [German] Die derzeitigen Entwicklungen im Flugzeugbau werden durch die allgemeine Forderung nach einer Steigerung der Wirtschaftlichkeit bestimmt. Das Laserstrahlschweissen ist dabei eines der vielversprechendsten Fuegeverfahren fuer die Anwendung im Flugzeugbau durch das die Herstellungskosten deutlich reduziert werden koennen. Zudem kann durch die Verwendung von leichten und hochfesten Aluminium-Legierungen das Gewicht einer Flugzeugstruktur zusaetzlich reduziert werden. Die vorliegende Arbeit befasst sich mit der Entwicklung eines Prozesses zum Laserstrahlschweissen einer Skin-Stringer-Verbindung aus den Aluminium-Lithium-Legierungen AA2196 (als Stringer-Werkstoff) und AA2198 (als Skin- und Stringer-Werkstoff). Unter Verwendung der statistischen Versuchsplanung wurden die optimalen Einstellungen der Schweissprozessparameter fuer die

  11. Friction conditions in the bearing area of an aluminium extrusion process

    NARCIS (Netherlands)

    Ma, X.; de Rooij, Matthias B.; Schipper, Dirk J.

    2012-01-01

    In aluminium extrusion processes, friction inside the bearing channel is important for controlling the surface quality of the extrusion products. The contact materials show a large hardness difference, one being hot aluminium, and the other being hardened tool steel. Further, the contact pressure is

  12. KS R41B. A high performance steel-aluminium composite material; KS R41B. Ein Stahl-Aluminium-Verbundwerkstoff fuer hohe Belastungen

    Energy Technology Data Exchange (ETDEWEB)

    Deicke, K. [KS Gleitlager GmbH (Germany). Bereich Metall; Matucha, H.; Schubert, W. [KS Gleitlager GmbH, St. Leon-Rot (Germany); Steffens, T. [KS Gleitlager GmbH, Neckarsulm (Germany)

    2002-08-01

    Aluminium-tin alloys have been well-known for a long time and have proved to be suitable bearing materials for crankshaft bearings for many years. The known alloy AlZn4,5SiCuPb is one of the aluminium materials capable of sustaining the highest mechanical loads. In order to achieve optimum sliding properties, it would be necessary to increase the share of the soft lead phase in the alloy. This article by KS Gleitlager GmbH shows a reasonably priced manufacturing technology for high-performance aluminium-zinc-silicon-copper alloys. (orig.) [German] Die Aluminium-Zinn-Lagerlegierungen sind seit langem bekannt und haben sich seit Jahren als Lagerwerkstoff fuer Kurbelwellenlager bewaehrt. Die Legierung AlZn4,5SiCuPb gehoert zu den mechanisch am hoechsten belastbaren Aluminium-Werkstoffen. Um optimale Gleiteigenschaften zu erzielen, muesste in der Legierung der Anteil des weichen Bleis noch weiter erhoeht werden. Dieser Beitrag der KS Gleitlager GmbH zeigt eine kostenguenstige Herstelltechnologie fuer hochbelastbare Aluminium-Zink-Silizium-Kupfer-Legierungen. (orig.)

  13. Corrosion Behavior of High Pressure Die Cast Al-Ni and Al-Ni-Ca Alloys in 3.5% NaCl Solution

    Energy Technology Data Exchange (ETDEWEB)

    Arthanari, Srinivasan; Jang, Jae Cheol; Shin, Kwang Seon [Seoul National University, Seoul (Korea, Republic of)

    2017-06-15

    In this investigation corrosion behavior of newly developed high-pressure die cast Al-Ni (N15) and Al-Ni-Ca (NX1503) alloys was studied in 3.5% NaCl solution. The electrochemical corrosion behavior was evaluated using open circuit potential (OCP) measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization results validated that NX1503 alloy exhibited lower corrosion current density (i{sub corr}) value (5.969 μA/cm{sup 2}) compared to N15 (7.387 μA/cm{sup 2}). EIS-Bode plots revealed a higher impedance (|Z|) value and maximum phase angle value for NX1503 than N15 alloy. Equivalent circuit curve fitting analysis revealed that surface layer (R{sub 1}) and charge transfer resistance (R{sub ct}) values of NX1503 alloy was higher compared to N15 alloy. Immersion corrosion studies were also conducted for alloys using fishing line specimen arrangement to simultaneously measure corrosion rates from weight loss (P{sub W}) and hydrogen volume (P{sub H}) after 72 hours and NX1503 alloy had lower corrosion rate compared to N15 alloy. The addition of Ca to N15 alloy significantly reduced the Al{sub 3}Ni intermetallic phase and further grain refinement may be attributed for reduction in the corrosion rate.

  14. Fatigue test on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, van IJ.J.

    2005-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge

  15. Advanced shipbuilding in aluminium

    International Nuclear Information System (INIS)

    Larsson, H.; Svensson, L.E.; Karlsson, L.

    1997-01-01

    The applicability of two different welding techniques for welding ships in aluminium is discussed. Conventional MIG welding and the recently developed Friction Super Stir Welding (FSSW) are compared concerning weld metal microstructures and mechanical properties. Results from testing of FSSW welds are also presented. It was observed that the grain size was smaller in FSSW welds are also presented. It was observed that the grain size was smaller in FSSW welds than in MIG welds whereas precipitates generally were larger in FSSW welds. The two methods produced welds with comparable mechanical properties. Good fatigue behaviour was obtained for FSSW welds. Advantages of the welding methods are also discussed. (Author) 7 refs

  16. USING OF PRESSURE DIES AT RUP «BMZ» FOR HIGH-SPEED WIRE DRAWING IN THE REGIME OF HYDRODYNAMIC FRICTION

    Directory of Open Access Journals (Sweden)

    D. G. Sachava

    2008-01-01

    Full Text Available It is shown that using of forcing dies at RUP «BMZ» for high-speed wire drawing in regime of hydrodynamic friction improves the quality of lubrication, and correspondingly fastness of dies incl. finishing ones is increaswd.

  17. Die rol van die blanke werker in die motivering van die swart werker

    Directory of Open Access Journals (Sweden)

    G. J. Oosthuizen

    1980-11-01

    Opsomming Die motivering van die Swart werker kan nie in die huidige situasie in isolasie bestudeer word nie, omdat die Blanke werker steeds in die bestuursposisie is en daarom die motivering van die Swart werker kan beïnvloed. Hierdie ondersoek was daarop gerig om die rol van die Blanke werker in die motivering van die Swart werker nader te ondersoek. Die houding en die leierskapsbenadering van die Blanke werker teenoor die Swart werker is gemeet, asook die behoeftes wat volgens die Blanke werker by die Swart werker bestaan, bevredig is, of nie bestaan nie. Die behoeftes van Swart werkers, soos deur hulleself gesien, is ook ondersoek. Ten opsigte van sekere aspekte is beduidende verskille gevind.

  18. Microstructure and property evaluation of high-pressure die-cast Mg–La–rare earth (Nd, Y or Gd) alloys

    International Nuclear Information System (INIS)

    Gavras, Serge; Easton, Mark A.; Gibson, Mark A.; Zhu, Suming; Nie, Jian-Feng

    2014-01-01

    Highlights: • Different rare earth elements have remarkably different effects on Mg castability. • For the addition of each RE element, the alloy castability follows a unique pattern. • The effects of RE elements on the castability can be modelled. - Abstract: Microstructure, castability and tensile properties were investigated in high-pressure die-cast Mg–La–Nd, Mg–La–Y and Mg–La–Gd alloy series, with a constant La concentration at approximately 2.5 wt.% and the concentrations of Nd, Y or Gd were varied. All three alloy series had a dendritic microstructure with a Mg–La-rich eutectic with increasing Nd, Y or Gd content and containing a Mg 12 RE intermetallic phase. The morphology of the eutectic at ternary alloying additions of equal to or less than 1.0 wt.% was lamellar but became increasingly divorced at higher ternary concentrations. This was however more obvious in Mg–La–Y and Mg–La–Gd than Mg–La–Nd alloys. The hot tearing susceptibility in all three alloy series increased markedly with even micro-alloying additions of Nd, Y or Gd, and began to decrease again in alloys with more than 0.5 wt.% Y or 1.0 wt.% Gd, but did not decrease significantly for Mg–La–Nd. A model using the temperature–fraction solid curves as input parameters was used to estimate hot tearing susceptibility for Mg–La–Nd alloys. Tensile testing at room temperature showed that Mg–La–Nd alloy series had higher 0.2% proof stress and lower elongation to failure than either the Mg–La–Y or the Mg–La–Gd alloy series for Nd concentrations greater than 1 wt.% due to a greater effectiveness of grain boundary reinforcement

  19. Die hervertolking van die paradigma in verband met die ...

    African Journals Online (AJOL)

    Kerkorde van De Mist en die Algemene Reglement van 1816, wat onderskeidelik vir die Kaapse Kerk en die .... Een van die eerstes was Sam Freiherr von Pufendorf (1632-1694) wat in sy werk De habitu religionis ..... Koning was weer aan bewind (vgl Diepenhorst sj:74w; De Visser 1926/1927 lll:202w). 43.1 JD Janssen ...

  20. die heidelbergse kategismus en die kategesemateriaal van die ned

    African Journals Online (AJOL)

    subjek, objek, leerstof en die metodiek van die senior kategese. Bloemfontein: Algemene Jeugkommissie Sondagskoolboekhandel. de rAAd oer ned ger kerken in Zuid AfrikA. 1921. De zevende vergadering: handelinge. 1925. De negende vergadering: handelinge. de villierS, d. W. 1957. Die Kategese in die Ned. Geref.

  1. die sinodale verband van die nederduitse gereformeerde kerk in die

    African Journals Online (AJOL)

    Liezel

    Strauss. Die sinodale verband van die Nederduitse Gereformeerde Kerk. 122 die Vrystaatse Sinode anti-veranderingsgesind of eerder gesond-behoudend of gereformeerd-gematig? Veral as dit .... howe) in moeilike omstandighede gebring is (NG Kerk in die OVS 1865-1912:5). In 'n brief op 8 Augustus 1864 ontken Ds.

  2. Die kerkregtelike posisie van die ouderling en diaken in die ...

    African Journals Online (AJOL)

    ... drie dekades die Kerkreg gevestig as 'n selfstandige vak in die teologiese curriculum, maar ook 'n baie groot rol gespeel daarin dat die beginsels van die kerk like reg beter begryp word. Naas sy wetenskaplike bydrae word met eweveel genoegdoening gedink aan sy bcsondere persoonlikheid, sy werkvermoe, sy humor-.

  3. Recycling of aluminium swarf by direct incorporation in aluminium melts

    OpenAIRE

    Puga, Hélder; Barbosa, J.; Soares, Delfim; Silva, Filipe Samuel; Ribeiro, Carlos Silva

    2009-01-01

    The purpose of this work was to recover a standard AlSi12Cu1 alloy from machining chips inside the foundry plant, by using an environmentally friend technique to produce cast ingots with characteristics similar to those of the commercially available 2nd melt raw material. The recyclability of aluminium swarf using different melting techniques and the influence of chips preparation in the aluminium alloy recovery rate and dross production was experimentally studied and evaluated...

  4. Aluminium, gallium, indium and thallium

    International Nuclear Information System (INIS)

    Brown, Paul L.; Ekberg, Christian

    2016-01-01

    Aluminium can exist in a number of oxyhydroxide mineral phases including corundum, diaspore, boehmite and gibbsite. The stability constants at zero ionic strength reported for Al(OH) 3 (aq) vary linearly with respect to the inverse of absolute temperature. A full suite of thermodynamic parameters is available for all aluminium phases and hydrolysis species. Gallium hydrolyses to a greater extent than aluminium, with the onset of hydrolysis reactions occurring just above a pHof 1. In fact, even though aluminium has the smallest ionic radius of this series of metals, it has the weakest hydrolysis species and oxide/hydroxide phases.This is due to the presence of stabilising d-orbitals in the heavier metals, gallium, indium and thallium(III). There are few available data for the stability constants of indium(III) hydrolysis species. Of those that are available, the range in the proposed stability constants covers many orders of magnitude.

  5. Riglyne vir die onderwys.

    Directory of Open Access Journals (Sweden)

    J. L. du Plooy

    1960-03-01

    Full Text Available In die afgelope vyftig jaar sedert die Unie tot stand gekom het, is veel op die gebied van onderwys tot stand gebring. Dit is heel natuurlik dat ’n mens sou vra: Wat van die toekoms?

  6. A laser-based study of kerosine evaporation and -mixing for lean prevaporized combustion at elevated pressure; Lasermesstechnische Untersuchung der Kerosinverdampfung und -mischung fuer die magere Vormischverbrennung unter erhoehtem Druck

    Energy Technology Data Exchange (ETDEWEB)

    Brandt, M.

    1999-05-01

    The evaporation and mixing of a kerosine spray in the turbulent airstream of a prevaporizer is investigated at conditions prevailing in the combustion chamber of gas turbines. An experiment is described that allows to study an evaporating fuel spray downstream a prefilming airblast atomizer with Phase-Doppler anemometry, laser-induced fluorescence and an infrared light absorption technique. At an air pressure of 9 bars, an air temperature of 750 K, a mean air velocity of 120 m/s and a fuel flow rate of 1 g/s the kerosine spray evaporates completely without autoignition. At this operating condition the parameters air pressure, air temperature and air turbulence are varied. The influence of these parametric variations on the dropsize distribution, the evaporation rate and the concentration profiles of liquid and evaporated fuel is presented and discussed. (orig.) [German] Die Verdampfung und Vermischung eines Kerosinsprays in der turbulenten Luftstroemung eines Vorverdampfers wird unter Bedingungen untersucht, die in Brennkammern fuer Gasturbinen vorherrschen. Ein Experiment wird vorgestellt, welches es erlaubt, ein verdampfendes Kraftstoffspray stromab eines ebenen Luftstromzerstaeubers mit Filmleger mittels der Phasen-Doppler-Anemometrie, Laser-induzierter Fluoreszenz und einer Infrarotabsorptionsmesstechnik zu untersuchen. Bei einem Luftdruck von 9 bar, einer Vorwaermetemperatur der Luft von 750 K, einer mittleren Luftgeschwindigkeit von 120 m/s und einem Kraftstoffmassenstrom von 1 g/s verdampft das Kerosinspray vollstaendig, ohne die Selbstzuendungszeit zu erreichen. Bei dieser Betriebsbedingung werden die Parameter Luftdruck, Lufttemperatur und Turbulenzgrad variiert. Der Einfluss dieser Parameter auf das Tropfengroessenspektrum, den Verdampfungsgrad und die Konzentrationsprofile des fluessigen sowie des verdampften Kraftstoffs wird dargestellt und diskutiert. (orig.)

  7. Die partypolitiek en die toekoms van die Afrikaanse volkskultuur

    Directory of Open Access Journals (Sweden)

    A.P. Treurnicht

    1970-03-01

    Full Text Available Reeds in 1853 het die Zuid Afrikaan hom soos volg uitgelaat: „Dis ’n dwaling wat ons reeds meermale bestry het dat ons as Britse onderdane verplig sou wees, om die Britse nasionaliteit ons s’n te maak. Die Kolonis van Hollandse oorsprong kan geen Engelsman word nie, en moet ook geen Nederlander wil wees nie. Wanneer hy weet om sy standpunt te waardeer, dan sal hy as verligte kolonis die grondtrekke van die Engelse volkskarakter met dié van die Nederlandse harmonies leer verenig en daardeur word wat hy as Kapenaar moet word.”

  8. Die Voortrekker-Monument

    Directory of Open Access Journals (Sweden)

    Gerard Moerdyk

    1938-03-01

    Full Text Available Die Eeufeesjaar is vir die Afrikaner ’n tydperk van besieling. Nog nooit sedert die ontstaan van ons volk het een enkele gebeurtenis soveel nasietrots gewek as die honderdjarige herdenking van die Groot Trek. Vir die eerste keer in ons geskiedenis voel ons ons nie meer Kapenaars, Vrystaters, Natalers, en Transvalers nie, maar Afrikaners, saamgesnoer deur die tradisies van ’n selfstandige kultuurvolk. Wanneer die klimaks van die Ossewatrek met die hocksteenlegging van die Voortrekker-Monument bereik word, sal die besieling nie uitsterf nie, die krag wat geskep is sal bly voortgroei tot ’n onweerstaanbare mag. Die Afrikaner sal homself vind, en as die Monument na sowat vyf jaar onthul word, sal die saad wat in hierdie jaar gesaai is, tot voile rypheid gekom het. Dan sal die Monument self tot die volk spreek; intussen egter, is dit wenslik, nee noodsaaklik selfs, om die Monument aan die Afrikaners te verklaar, om ‘n uiteensetting te gee van die noodsaaklikheid van so ’n Monument, sowel as om die motief te verduidelik wat as inspirasie gedien het vir die ontwerpdaar van.

  9. Alloys of uranium and aluminium with low aluminium content

    International Nuclear Information System (INIS)

    Cabane, G.; Englander, M.; Lehmann, J.

    1955-01-01

    Uranium, as obtained after spinning in phase γ, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase α) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl 2 ) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl 2 particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

  10. Experimental analysis of cut welding in aluminium

    DEFF Research Database (Denmark)

    Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

    1993-01-01

    Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...... tensile testing and metallographic investigations of the welds. The results show that this variant of cut welding is a very reproducible process giving a weld strength equal to 30-40% the strength of the parent material. The experiments have shown that the reason for this relatively low strength...... is an uneven pressure distribution along the weld due to a wave formed during sliding. Attempts to alter the material flow during sliding are presented....

  11. Die Britse owerheid en die onderwys op Heidelberg gedurende die ...

    African Journals Online (AJOL)

    The establishment of Christian National Education (CNE) Schools stimulated the concept of mother tongue education. Oor die klaskamerpraktyk en die werklike gehalte van onderrig tydens die kampskooltydperk is daar min bekend. Heidelberg wat na 1902 in 'n belangrike onderwyssentrum in Transvaal ontwikkel het, het ...

  12. Die belangrikste kenmerk van die diereproduksie- bedrywe oor die ...

    African Journals Online (AJOL)

    digdhede teen 1980 uit 'n kudde van 30 rnilj.skape ge- produseer moet word. Tweedens sal die faktore ... die Republiek van Suid-Mrika teen 1980 in totaal 28 milj. sal wees. Indien die produsente dit as 'n ..... Appendix Table 4 in Digestive Physiology and nutrition of ruminants Vol. 3 Ed. and Publ. D.C. Church, Oregon State ...

  13. DIE ROL VAN DIE TAALWETENSKAP IN DIE ONTWIKKELING VAN ...

    African Journals Online (AJOL)

    aanslag op die sogenaamde "Intentional Fallacy", heelwat verder. n. Mens sou hier eintlik ook op die invloed van Lacan se toepassing van. De Sacs sure op Freud moet wys, en op Macherey se Theory of Literary. Production. Barthes is naamlik besig om repressie teen te werk, en die teks as produksieproses in stede van ...

  14. Development of solar selective absorber layers on aluminium. Final report; Entwicklung solarselektiver Absorberschichten auf Aluminium fuer Solarkollektoren. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Hoenicke, D.; Moeller, T.; Schwarz, T.

    1998-01-31

    A new electrolytic process was developed to form solar selective layers on aluminium. In the developed process, both the formation of the alumina layer and the deposition of metals into the layer takes place in only one treatment step using a single electrolysis bath. The main step of the so called ISOC-method (impulse structured oxide ceramic) is the anodic oxidation of aluminium which was carried out by using a pulse technique at different voltages. During the anodic polarisation a thin alumina ceramic layer was formed, while the cathodic led to the metal deposition as copper and nickel. The conditions of the electrolysis were varied in order to estimate optimal parameters achieving solar selective layers with high selectivity. Furthermore, a scale-up of the lab scale apparatus to a mini plant was carried out. Finally, the corrosion resistance of the absorber layers was improved by the formation of a thin hydrophobic overlayer using a sol-gel treatment. (orig.) [Deutsch] Ein neuartiges Behandlungsverfahren zur Erzeugung von solarselektiven Absorberschichten auf Aluminium wurde entwickelt. Bei dieser elektrochemischen Behandlung wird in einem Einstufenprozess mit einem Elektrolyten durch eine Kombination von anodischer Oxidation und bipolarer Pulsbehandlung auf der Oberflaeche des Aluminiums eine impulsstrukturierte Oxidkeramik (ISOK) erzeugt. Dabei entsteht durch eine anodische Oxidation eine strukturierte Aluminiumoxidschicht. Bei der bipolaren Pulsbehandlung erfolgt dann eine Abscheidung der im ISOK-Elektrolyten befindlichen Metalle Cu und Ni auf oder in die Aluminiumoxidoberflaeche. Die ISOK-Behandlung wurde vom Labormassstab zu einem ISOK-Verfahren im Miniplant-Massstab entwickelt. Der Einfluss der elektrischen Parameter und der chemischen Zusammensetzung der ISOK-Elektrolyte wurde untersucht. Durch eine auf das ISOK-Verfahren abgestimmte Nachbehandlung, ein Tauchverfahren in einer Sol-Gel-Loesung, entsteht ein Schichtsystem mit hoher Solarselektivitaet

  15. Dispersion strengthening of aluminium-aluminium-oxide products

    DEFF Research Database (Denmark)

    Hansen, Niels

    1970-01-01

    The true stress-true strain curves at room temperature and at 400°C were determined for various types of aluminium-aluminium-oxide products containing from 0.2 to 4.7 weight per cent of aluminium oxide. The effect of particles on the initial flow stress and the flow stress for 0.2% offset at room...... temperature and at 400°C is in agreement with Orowan's theory. The increase in flow stress at room temperature for strain values below 3 per cent was related to the plastic strain by the equation σ-σoy=k1ε 1/2, where σoy is the initial flow stress and where k1 increases for increasing volume fraction...... and decreasing particle size of the dispersed particles. A general expression for k1 was derived for the relationship between the dislocation density and the strain in dispersion-strengthened products...

  16. Microstructure and properties of aluminium-aluminium oxide graded composite materials

    Science.gov (United States)

    Kamaruzaman, F. F.; Nuruzzaman, D. M.; Ismail, N. M.; Hamedon, Z.; Iqbal, A. K. M. A.; Azhari, A.

    2018-03-01

    In this research works, four-layered aluminium-aluminium oxide (Al-Al2O3) graded composite materials were fabricated using powder metallurgy (PM) method. In processing, metal-ceramic graded composite materials of 0%, 10%, 20% and 30% weight percentage of ceramic concentration were prepared under 30 ton compaction load using a cylindrical die-punch set made of steel. After that, two-step pressureless sintering was carried out at sintering temperature and time 600°C and 3 hours respectively. It was observed that the sintered cylindrical specimens of 30 mm diameter were prepared successfully. The graded composite specimens were analysed and the properties such as density, microstructure and hardness were measured. It was found that after sintering process, the diameter of the graded cylindrical structure was decreased. Using both Archimedes method and rule of mixture (ROM), he density of structure was measured. The obtained results revealed that the microvickers hardness was increased as the ceramic component increases in the graded layer. Moreover, it was observed that the interface of the graded structure is clearly distinguished within the multilayer stack and the ceramic particles are almost uniformly distributed in the Al matrix.

  17. Alloys of uranium and aluminium with low aluminium content; Alliages uranium-aluminium a faible teneur en aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Cabane, G; Englander, M; Lehmann, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    Uranium, as obtained after spinning in phase {gamma}, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase {alpha}) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl{sub 2}) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl{sub 2} particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

  18. Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

    DEFF Research Database (Denmark)

    Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib

    2007-01-01

    A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis...... aluminium content in aluminium hydroxide suspension. (c) 2007 Elsevier Ltd. All rights reserved....

  19. Synthesis and properties of bimetallic aluminium alkoxides

    International Nuclear Information System (INIS)

    Vyshinskaya, K.I.; Vasil'ev, G.A.; Vishnyakova, T.A.

    1997-01-01

    A single stage method of aluminium bimetallic alkoxide synthesis, which consists in activated aluminium reaction with metal salts in the relevant alcohols, has been developed. Properties of the compounds prepared are described

  20. Preparation of aluminium lakes by electrocoagulation

    OpenAIRE

    Prapai Pradabkham

    2008-01-01

    Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  1. Effect of hydrogen on aluminium and aluminium alloys: A review

    DEFF Research Database (Denmark)

    Ambat, Rajan; Dwarakadasa, E.S.

    1996-01-01

    Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

  2. Wêreldmededingendheid en die tegnologie

    Directory of Open Access Journals (Sweden)

    C. W. I. Pistorius

    1996-07-01

    Full Text Available Afgesien van die interne uitdagings wat die Heropbou- en Ontwikkelingsprogram (HOP aan Suid-Afrika bied, moet die land ook tred hou met die veranderende globale omgewing, spesifiek die toenemende belangrikheid van ekonomiese sekuriteit as komponent van nasionale sekuriteit. Die konsep van mededingendheid vergestalt die doelwit wat nagestreef moet word ten einde die ontluikende globale ekonomiese stryd aan te durf. As ’n belangrike drywer van ekonomiese welvaart is tegnologie een van die belangrikste sleutels tot internasionale mededingendheid. Tegnologiese innovasie is die proses wat as hefboom hiervoor gebruik moet word. Dit is egter nodig dat tegnologie, en spesifiek die proses van tegnologiese innovasie, formeel en gestruktureerd bestuur moet word, sowel op nasionale as firmavlak. Op nasionale vlak is die voorsiene Nasionale Innovasiestelsel beslis ’n stap in die regte rigting.

  3. Chapter 2. Theoretical aspects of aluminium production

    International Nuclear Information System (INIS)

    Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

    2011-01-01

    This article is devoted to theoretical aspects of aluminium production. Thus, the electrochemistry of electrolysis process, calculation of base industrial indicators of aluminium electrolytic cell, and processes occurring on anode and cathode were considered. Factors, which increase the current output and electrolytic cell productivity were studied. The side effects, including anode effect, sodium extraction on cathode, aluminium dissolution in the electrolyte, aluminium carbide formation, and influence of admixtures in the electrolyte were studied as well.

  4. die ontstaan en die ontwikkeling van die skoolkadette-stelsel in die rsa

    African Journals Online (AJOL)

    toe algemene diensplig ingestel is. Die diens- plig het intussen sy volle beslag gekry en in. Weermagkringe het die gedagte posgevat dat skoolkadette. 'n deeglike ondersoek vereis ten einde die skoolgaande seun vir sy komende nasionale diensplig te orienteer. Tydens kadetopleldlng leer die seuns al die fynere kunsles ...

  5. Van die Gasredakteur

    African Journals Online (AJOL)

    cherish and teach.'1. Die Fakulteit Geneeskunde van die Universiteit van die Oranje-Vrystaat het pragtig gegroei ge- durende die eerste 21 jaar van sy bestaan. Die entoesiasme, doelgerigtheid, harde werk en inisia- tiewe van 'n groot aantal persone was hiervoor verantwoordelik. 'If we see a bit more clearly than they, it is ...

  6. Halfkrone vir die Nagmaal

    African Journals Online (AJOL)

    Owner

    die omgewing van Velddrif en Laaiplek, ook noordwaarts verby Lambertsbaai tot by. Doringbaai en Strandfontein. “Haar seeverhale is Sussie (Kotze) se belangrikste bydrae tot die Afrikaanse letterkunde”, sê Kotzé-Myburgh in die voorwoord van die versamelbundel. Die leser word herinner aan Kotze se debuutroman, ...

  7. Die teologie in gesprek met die ekonomie

    African Journals Online (AJOL)

    (1723-1790) sy vertrekpunt neem, ontwikkel, as oorwinnaars uit die Franse Revolu .... Die onmiddellike sukses van Adam Smith se 'Wealth of Nations' was .... alle vorme van sosialisme niks anders as 'kommunisme' (Wassenaar 1977:12) nie.

  8. Design and analysis of aluminium brdiges

    NARCIS (Netherlands)

    Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Applications of aluminium have grown considerably in building and civil engineering the last decade, which is due to various aspects: light weight, durability and maintenance, use of extrusions. The paper starts with a short history of aluminium bridges and then focuses on aluminium bridges in the

  9. Hot workability of aluminium alloys

    International Nuclear Information System (INIS)

    Yoo, Yeon Chul; Oh, Kyung Jin

    1986-01-01

    Hot Workability of aluminium alloys, 2024, 6061 and 7075, has been studied by hot torsion tests at temperatures from 320 to 515 deg C and at strain rates from 1.26 x 10 -3 to 5.71 x 10 -3 sec -1 . Hot working condition of these aluminium alloys was determined quantitatively from the constitutive equations obtained from flow stress curves in torsion. Experimental data of the logarith of the Zener-Hollomonn parameter showed good linear relationships to the logarith of sinh(ασ-bar)

  10. Die dogmatiese binding van die prediking

    African Journals Online (AJOL)

    genoemde probleemstelling wat ons homileties na riglyne wil soek, sonder die pretensie dat finale oplossings gevind sal word. Om hierdie probleem te ontleed is dit nodig om eers kortliks 'n begripsbepaling van die begrippe dogma, binding en prediking te maak. Vanuit die begripsbepaling kan ons dan probeer vasstel wat ...

  11. DIE PERSOON VAN VREDE IN DIE SENDING

    African Journals Online (AJOL)

    aan dat 'n lewe onder die gesag van God tot volle vrede lei: “In coming under the rule of Yahweh, moreover, life was made whole and safe.” Dit is spesifiek in die tempel waar die volheid van God se vrede ondervind word (1997:662):. The temple is indeed the place where Israel entered into Yahweh's full zone of shalom.

  12. Influence of aluminium content on thermodynamic function of LaNi5-xAlx

    International Nuclear Information System (INIS)

    Xiong Yifu; Cheng Huchi; Luo Deli

    2000-01-01

    Hydriding thermodynamic parameters were measured on alloys of the general composition of LaNi 5-x Al x (x = 0.0, 0.1, 0.2, 0.3) under isothermal and isochoric conditions. The results show that the equilibrium pressure, hydrogen capacity and thermodynamic parameters such as ΔH, ΔS decrease with aluminium content, plateau slopes of the P-C-T curve increase with aluminium content

  13. n Oorsig van die huidige stand van navorsing oor die

    African Journals Online (AJOL)

    Test

    7 Jun 2011 ... Die eerste maal wat dit as deel van die teks van 1 Johannes aangehaal word, is in die. 4de eeu in 'n Latynse teks, Liber Apologeticus (hf 4). Eers aan die einde van die 16de eeu is dit in 'n amptelike Katolieke uitgawe van die Vulgaat ingesluit. Die doel van die Johannesbriewe. Waarom is die Briewe ...

  14. Die Ware Buch und die Philologie

    Directory of Open Access Journals (Sweden)

    Bernhard Hurch

    2017-10-01

    Full Text Available Die im 19. Jahrhundert sich verändernden Produktionsbedingungen für Druckwerke (Buchdruck, Satz, Papier, Bindung wirkten katalysierend auf die Fachkonstitution und Institutionalisierung der Philologien. Hier steht der tatsächliche Buchmarkt im Vordergrund der Darstellung, das Käuferpublikum und die Voraussetzungen des Vertriebs. Dazu gehören auch die Rezension als entstehende Textsorte und die rasch arbeitenden Rezensionsorgane. F.-R. Hausmann wurde in den letzten Jahren unentbehrlicher Mitarbeiter dieses im Rahmen des Grazer Schuchardt-Projekts "Netzwerk des Wissens" angesiedelten Ansatzes.

  15. Developments in the US aluminium recycling industry

    Energy Technology Data Exchange (ETDEWEB)

    Bolling, R N

    1983-06-01

    In the USA scrap recovery of aluminium has gained in importance since the war. Today its amounts to about 32% of total supply. On the other hand primary production in the US seems to have hardly any expansion possibilities. The development of the aluminium beverage can is the clearest example for recycling growth. The increased use of aluminium in passenger cars has led to very close technical and local relations of aluminium foundries and secondary smelters. The changing nature of the aluminium business caused by the growth of recycling should be recognized and made use of.

  16. The prophylactic reduction of aluminium intake.

    Science.gov (United States)

    Lione, A

    1983-02-01

    The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail.

  17. Aluminium and energy. An interview

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, E R

    1978-06-01

    The interview between METALL and the president of Aluswuisse refers mainly to aspects of energy and deals more closely with the questions whether western Europe in view of relatively high prices for electricity is still competitive and which part can be played by aluminium in overcoming the energy crisis.

  18. Recovery mechanisms in nanostructured aluminium

    DEFF Research Database (Denmark)

    Yu, Tianbo; Hansen, Niels; Huang, Xiaoxu

    2012-01-01

    Commercial purity aluminium (99.5%) has been cold rolled to a true strain of 5.5 (99.6% reduction in thickness). The material is very strong but low temperature recovery may be a limiting factor. This has been investigated by isothermal annealing treatments in the temperature range 5–100C. Hardness...

  19. Dynamical study of liquid aluminium

    International Nuclear Information System (INIS)

    Dubey, G.S.; Chaturvedi, D.K.

    1979-09-01

    Recent molecular dynamics data of Ebbsjoe et al. in liquid aluminium have been analysed through the memory function formalism. Two forms of the memory functions which have correct asymptotic limit at large wavenumbers but accounts for interatomic correlations in a different manner are considered. The results for ω 2 s(q, ω) obtained from both models are compared with experimental data. (author)

  20. Hydrogen generation from aluminium corrosion in reactor containment spray solutions

    International Nuclear Information System (INIS)

    Frid, W.; Karlberg, G.; Sundvall, S.B.

    1982-01-01

    The aluminium corrosion experiments in reactor containment spray solutions, under the conditions expected to prevail during LOCA in BWR and PWR, were performed in order to investigate relationships between temperature, pH and hydrogen production rates. In order to simulate the conditions in a BWR containment realistic ratios between aluminium surface and water volume and between aluminium surface and oxygen volume were used. Three different aluminium alloys were exposed to spray solutions: AA 1050, AA 5052 and AA 6082. The corrosion rates were measured for BWR solutions (deaerated and aerated) with pH 5 and 9 at 50, 100 and 150 0 C. The pressure was constantly 0.8 MPa. The hydrogen production rate was measured by means of gas chromatography. In deionized BWR water the corrosion rates did not exceed about 0.05 mm/year in all cases, i.e. were practically independent of temperature and pH. Hydrogen concentrations were less than 0.1 vol.% in cooled dry gas. Corrosion rates and hydrogen production in PWR alkaline solution measured at pH 9.7 and 150 0 C were very high. AA 5052 alloy was the best material

  1. Lead inclusions in aluminium

    International Nuclear Information System (INIS)

    Johnson, E.; Johansen, A.; Sarholt-Kristensen, L.; Andersen, H.H.; Grabaek, L.; Bohr, J.

    1990-01-01

    Ion implantation at room temperature of lead into aluminum leads to spontaneous phase separation and formation of lead precipitates growing topotactically with the matrix. Unlike the highly pressurized (∼ 1-5 GPa) solid inclusions formed after noble gas implantations, the pressure in the lead precipitates is found to be less than 0.12 GPa. Recently the authors have observed the result that the lead inclusions in aluminum exhibit both superheating and supercooling. In this paper they review and elaborate on these results. Small implantation-induced lead precipitates embedded in an aluminum matrix were studied by x-ray diffraction

  2. Effect of Bio char on Plant Growth and Aluminium Form of Soil under Aluminium Stress

    Science.gov (United States)

    Qian, Lianwen; Li, Qingbiao; Sun, Jingwei; Feng, Ying

    2018-01-01

    Aluminium-enriched acid red soils in South China easily cause aluminium toxicity to plants, but biochip can improve soils and eliminate soil contaminations. In this project, biochip was used in potted plant control test to study the effect of biochip on plant growth in soil under acid aluminium stress and the migration and conversion of aluminium in plant-soil system. The fin dings show that the application of biochip increases the pH value of soil under aluminium stress significantly, changes the existing form of aluminium ion in soil, reduces the plants’ absorption of aluminium, and alleviates the aluminium toxicity to plants, but too much biochip may inhibit the growth of plants. In this case, further study should be carried out as regards the volume and way of biochip input in practical applications as well as the timeliness of aluminium toxicity removal.

  3. Die vrede van Münster / Westfale en die betekenis daarvan vir die ...

    African Journals Online (AJOL)

    In die Suid-Afrikaanse kerkgeskiedenis egter is die Vrede van Münster as epogmakende gebeure tot dusver nie net in die algemeen verwaarloos nie, maar boonop is die direkte verband tussen hierdie sentrale historiese baken aan die een kant en aan die ander kant die vestiging van die VOC se verversingspos aan die ...

  4. Tegnologie en die mens

    African Journals Online (AJOL)

    omgewingsbesoedeling, volgend op industrialisasie en verstedeliking, gee uit- ing tot krete van wanhoop en frustrasie. Die maatskaplike ontwrigting agv outomatisasie het die begrippe van vervreemding en naam- loosheid op die voorgrond van sosiale be- wustheid geplaas. • Die Neutrale Siening. Tegnologie was nag. 34.

  5. GODSBEELDE IN DIE LITURGIE

    African Journals Online (AJOL)

    15 Mei 2010 ... Biezeveld, de Boer, Brümmer, Muis. 2001; Brown 2006; Durand 2007). ... Wanneer sal hy weer in God se teenwoordigheid verskyn (vers 3)? Dié vraag is vol onsekerheid. (Schuman 2004:8). Sy onsekerheid ... God se volk en die enkeling in die geskiedenis het al die trou van God ervaar waarop die digter ...

  6. Die ontwikkeling van die bestuursmotiveringsvraelys (BMV

    Directory of Open Access Journals (Sweden)

    A. S. Engelbrecht

    1991-06-01

    Full Text Available The development of the Managerial Motivation Questionnaire (MMQ: Several criticisms of the psychometric suitability of existing measures of managerial motivation are reported in the literature. This study aimed at developing a new psychometrically sound instrument, the Managerial Motivation Questionnaire (MMQ. This was done on the basis of a comprehensive study of the literature on managerial motivation and the role-motivation theory. The preliminary MMQ was systematically shortened and refined until the final MMQ of 98 items was composed. This was based on social desirability and semantic appraisal, item analysis and factor analysis of the questionnaire. The results indicate that it was possible to develop a final MMQ that was relatively free of social desirability. It further demonstrated satsifactory internal consistencies on two samples (a = 0/90, N = 360; a = 0/91, N = 535, where all subscale items were found to be relatively pure measures of the isolated factors. Although some evidence was found providing support for the reliability of the MMQ, a need for further research on the construct validity of managerial motivation still exists. Opsomming In die literatuur word verskeie punte van kritiek teen die psigometriese geskiktheid van bestaande meetinstrumente van bestuursmotivering gerapporteer. Die doelstelling van hierdie studie was dus om aan die hand van die konseptuele omiyning van bestuursmotivering, en die rolmotiveringsteorie as algemene verwysingsraamwerk, 'n nuwe psigometries aanvaarbare meetinstrument, die Bestuursmotiveringsvraelys (BMV, te ontwikkel. Op grond van sosiale wenslikheids- en semantiese beoordeling, itemontleding en faktorontleding van die voorlopige BMV is die vraelys stelselmatig verkort en verfyn totdat die finale BMV van 98 items saamgestel is. Die resultate dui daarop dat hierdie studie wel daarin geslaag het om 'n finale BMV te ontwikkel wat relatief vry van sosiale wenslikheid is, bevredigende interne

  7. Varswateralge en die ekonomie

    Directory of Open Access Journals (Sweden)

    W. E. Scott

    1988-03-01

    Full Text Available Die artikel bespreek die ekonomiese belong wat varswateralge alreeds het en hul moontlike verdere ontginning in die toekoms. Sowel gewenste as ongewenste aspekte word oorweeg en hoofsaaklik met voorbeelde uit Suid-Afrika geïllustreer. Die oormatige ontwikkeling van ongewenste alge in varswater verlaag die watergehalte dear verskeie chemiese veranderinge, wat kan wissel van smake en geure tot die produksie van verbindings wat gesondheidsgevare vir mens of dier inhou. Verwydering van ongewenste alge dra aansienlik by tot die koste van waterbehandeling. Oormatige alggroei belemmer ontspanningsgebruike en kan eiendomswaardes langs rivier- en damoewers beïnvloed.

  8. Prediking aan die hand van die metafoor van fiksieskryf

    African Journals Online (AJOL)

    p1243322

    HTS 64(3) 2008 siening van die self en waarheid. In die pre-moderne paradigma kan die dominante metafoor verstaan word aan die hand van 'n spieël wat die lig uit 'n transendente oorsprong weerkaats, terwyl die moderne paradigma uitgedruk word met die metafoor van 'n lamp wat 'n eie, oorspronklike lig binne die self.

  9. e .Kuraioriufn. DIE W ETENSKAPLIKE BETEKENIS VAN DIE W ERK

    African Journals Online (AJOL)

    Test

    ENGELBRECHT ver antwoordelik vir die Ou-Testamentiese vakke en Hebreeus. Die aan stelling van 'n derde professor het noodsaaklik geword, want dit sou. 85 .... De .Spreuken ran 5a/o?no omvat die nuwe vertaling en die ekse gese van die eerste 24 hoofstukke van die Spreukeboek. Die geskoold- heid in die Semitiese ...

  10. Friction Welding of Aluminium and Aluminium Alloys with Steel

    Directory of Open Access Journals (Sweden)

    Andrzej Ambroziak

    2014-01-01

    Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

  11. Bumblebee pupae contain high levels of aluminium.

    Science.gov (United States)

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  12. Die dialogiese prinsipe

    Directory of Open Access Journals (Sweden)

    J. J. de Klerk

    1981-08-01

    Full Text Available Met die dialogiese prinsipe word daardie beginsel bedoel, waarin die tweerigtingverkeer of kommunikasie onder, of met, of deur die mense op 'n heel besondere gesprekmatige wyse gere�l word. Tot die wese van die dialogiese prinsipe behoort "als Grundvoraussetzung das Ernstnehmen des Gesprachspartners und das darin enthaltene zuhoren-konnen. Dialog ist also etwas anderes als Disput oder Diskussion. Er setzt gegenseitiges Vertrauen und Hochachtung voraus."

  13. Die sestienpersoonlikheidsfaktorvraelys as hulpmiddel by die takseersentrum

    Directory of Open Access Journals (Sweden)

    J. C. D. Augustyn

    1988-05-01

    Full Text Available The 16PF Personality Test as an aid to the assessment centre Assessment centres still remains costly and thime consuming. This study investigates the reduction of time and costs by the use of the 16 PF Personality Test as a method for measuring management dimensions. Promising results were obtained with a relatively small sample for the prediction of initiative and perseverance. Significant multiple correlations were also found for three criteria of management success. Further research may establish the use of the 16 PF as an aid to management assessment and thereby reduce the costs and time involved in assessment centres. Opsomming Takseersentrums se grootste probleem is gelee in die koste en tyd wat dit behels. Hierdie studie ondersoek die moontlikheid om beide te verminder deur die aanwending van die 16 PF Persoonlikheidsvraelys vir die meting van bestuursdimensies. Belowende resultate is met 'n relatiewe klein steekproef bevind ten opsigte van die voorspelling van inisiatiefen deursettingsvermoe. Beduidende meervoudige korrelasies is ook ten opsigte van drie kriteria van bestuursukses bevind. Verdere navorsing kan die gebruik van die 16 PF as hulpmiddel by bestuursevaluering vestig en sodoende die tydsduur en koste van takseersentrums verminder.

  14. Numerical simulation and experiment on multilayer stagger-split die.

    Science.gov (United States)

    Liu, Zhiwei; Li, Mingzhe; Han, Qigang; Yang, Yunfei; Wang, Bolong; Sui, Zhou

    2013-05-01

    A novel ultra-high pressure device, multilayer stagger-split die, has been constructed based on the principle of "dividing dies before cracking." Multilayer stagger-split die includes an encircling ring and multilayer assemblages, and the mating surfaces of the multilayer assemblages are mutually staggered between adjacent layers. In this paper, we investigated the stressing features of this structure through finite element techniques, and the results were compared with those of the belt type die and single split die. The contrast experiments were also carried out to test the bearing pressure performance of multilayer stagger-split die. It is concluded that the stress distributions are reasonable and the materials are utilized effectively for multilayer stagger-split die. And experiments indicate that the multilayer stagger-split die can bear the greatest pressure.

  15. DIE GESKIEDENIS VAN AFDELING LOGISTIEK

    African Journals Online (AJOL)

    1 Aug 1978 ... dan ook aangebied, Agv die probleem wat ont- staan het met die gebrek aan goedgekeurde poste vir die Afdeling en as gevolg van die ver- wagte vertraging met die ondersoek van die. DOS-span, het die Afdeling Logistiek en Afde- ling Personeel oorleg gepleeg en laasgenoemde het ingestem dat die ...

  16. Power distribution: conductors in aluminium

    International Nuclear Information System (INIS)

    Schmid, R.

    2007-01-01

    This article takes a look at the use of aluminium conductors in medium and low-voltage cables. The author discusses how the increasing price of copper has led to the increasing use of aluminium as a material for the production of the conductors used in medium and low-voltage power cables. Aid is provided that is to help purchasers make the correct decisions when buying medium and low-voltage cables. The current market situation is examined and the appropriate norms are looked at. Technical data and economic aspects are discussed, both for medium and low-voltage applications. The electrical characteristics of the type of cable to be used are examined and discussed

  17. Neutron Cross Sections for Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, Leif

    1963-08-15

    Total, elastic, inelastic, (n, 2n), (n, {alpha}), (n, p), and (n, {gamma}) cross sections for aluminium have been compiled from thermal to 100 MeV based upon literature search and theoretical interpolations and estimates. Differential elastic cross sections in the centre of mass system are represented by the Legendre coefficients. This method was chosen in order to obtain the best description of the energy dependence of the anisotropy.

  18. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

  19. Surface treatments for aluminium alloys

    Science.gov (United States)

    Ardelean, M.; Lascău, S.; Ardelean, E.; Josan, A.

    2018-01-01

    Typically, in contact with the atmosphere, the aluminium surface is covered with an aluminium oxide layer, with a thickness of less than 1-2μm. Due to its low thickness, high porosity and low mechanical strength, this layer does not protect the metal from corrosion. Anodizing for protective and decorative purposes is the most common method of superficial oxidation processes and is carried out through anodic oxidation. The oxide films, resulted from anodizing, are porous, have a thickness of 20-50μm, and are heat-resistant, stable to water vapour and other corrosion agents. Hard anodizing complies with the same obtains principles as well as decorative and protective anodization. The difference is in that hard anodizing is achieved at low temperatures and high intensity of electric current. In the paper are presented the results of decorative and hard anodization for specimens made from several aluminium alloys in terms of the appearance of the specimens and of the thickness of the anodized.

  20. Die relevansie van die boek Prediker

    African Journals Online (AJOL)

    ook in die dogmatiek te bespeur is nie. 'n Vinnige oorsig oor die teksverwysings van. 'n paar wydgelese dogmatiekhandboeke kan dit bevestig. In Karl Barth se omvang- ryke Kirchliche Dogmatik word Prediker slegs vyf en dertig maal aangehaal en slegs sewe maal word teksgedeeltes bespreek. Emil Brunner haal Prediker ...

  1. Hatchability and survival of oncomiracidia of Paradiplozoon ichthyoxanthon (Monogenea: Diplozoidae) exposed to aqueous aluminium.

    Science.gov (United States)

    Gilbert, Beric M; Avenant-Oldewage, Annemariè

    2016-07-28

    Monogenea is a diverse group of ectoparasites showing great potential as sentinel organisms for monitoring environmental health. Exposure to metals negatively affects infrapopulations of monogeneans and exposure to aluminium has been found to negatively impact the survival of gyrodactylids. Samples of infected host fish, the smallmouth yellowfish Labeobarbus aeneus (Cyprinidae), were collected from the Vaal Dam, South Africa and transported back to the laboratory in dark 160 l containers. Eggs of the monogenean Paradiplozoon ichthyoxanthon infecting L. aeneus were collected and exposed to varying concentrations of aluminium along with a control group in static tanks. The eggs were checked every 24 h and hatching commenced 13-14 days after exposure. Water samples were taken from exposure tanks and acidified for analysis of Al levels with inductively-coupled plasma mass spectrometry. Hatching of eggs was variable between exposures, and in 30 μg Al/l and 60 μg Al/l was found to occur before eggs in control beakers, whereas, exposure to 120 μg Al/l delayed hatching and reduced hatchability. Survival of hatched oncomiracidia was concentration dependent and negatively correlated with aluminium concentrations. Lowest survival was recorded for 60 μg Al/l and 120 μg Al/l where all larvae died shortly after or during hatching. Normal development of embryos of P. ichthyoxanthon within eggs exposed to all doses of aluminium indicates that the egg shell is moderately impermeable to metals and inhibits movement of aluminium across the shell and interacting with developing embryos. Higher larval mortality rate in 120 μg/l exposure can be related to aluminium crossing the egg shell in the late stages and causing death of unhatched yet fully developed embryos, possibly due to changes in the permeability of the egg shell as embryos neared developmental completion. Accelerated death of oncomiracidia after hatching indicates sensitivity toward high concentrations of aluminium.

  2. Thermodynamics of carbon deoxidation and aluminium deoxidation of refractory metals

    International Nuclear Information System (INIS)

    Garg, S.P.; Sundaram, C.V.

    1975-01-01

    Carbon has been used for removing the last traces of oxygen from many refractory metals by evaporation of CO at high temperature and vacuum. Similar purification can also be achieved employing aluminium deoxidation by evaporation of Al 2 Osub(g). In the present paper a theoretical thermodynamic approach has been attempted to evaluate the deoxidation tendencies of refractory metals of groups IV to VI by these two processes. Expressions have been theoretically derived, relating the concentration product of carbon and oxygen in the metal (which is a measure of the carbon deoxidation tendency of the metal) with temperature and pressure, for various M-C-O systems. Similarly the relative vapour pressure values of Alsub(2)Osub(g),Alsub(g)andMO(g) (suboxide of the metal) over various M-Al-O systems have been calculated as a function of aluminium and oxygen contents of the metal. From these analyses, it has been shown that a substantial amount of oxygen can be removed from M-Al-O alloys by aluminium deoxidation. The estimated values are compared with the reported values based on experiment. (author)

  3. Nano Precipitation and Hardening of Die-Quenched 6061 Aluminum Alloy.

    Science.gov (United States)

    Utsunomiya, Hiroshi; Tada, Koki; Matsumoto, Ryo; Watanabe, Katsumi; Matsuda, Kenji

    2018-03-01

    Die quenching is applied to an age-hardenable aluminium alloys to obtain super-saturated solid solution. The application is advantageous because it can reduce number of manufacturing processes, and may increase strength by strain aging. If die quenching is realized in forging as well as sheet forming, it may widen industrial applicability further. In this study, Al-Mg-Si alloy AA6061 8 mm-thick billets were reduced 50% in height without cracks by die-quench forging. Supersaturated solid solution was successfully obtained. The die-quenched specimen shows higher hardness with nano precipitates at shorter aging time than the conventional water-quenched specimen.

  4. Detection of aluminium in different culinary media using black ...

    African Journals Online (AJOL)

    Jacques Blessing

    The interactions between food and aluminium local kitchen utensils can be a potential source of aluminium released which can ... need to be adopted to preserve consumers' health. ..... Corrosion behaviour of different ... Aluminium beverage.

  5. Introduction. Aluminium production on electrolytic cells with calcined anodes

    International Nuclear Information System (INIS)

    Galushkin, N.V.

    1995-01-01

    This chapter presents the monograph content, which includes the description of physicochemical processes in aluminium electrolytic cells, and mechanism of electrolytic aluminium obtaining. The short description of aluminium electrolytic cells construction is presented in this book as well.

  6. Coprecipitation of yttrium and aluminium hydroxide for preparation of yttrium aluminium garnet

    NARCIS (Netherlands)

    Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.

    1990-01-01

    Coprecipitation of yttrium and aluminium hydroxide for the preparation of pure yttrium aluminium garnet (YAG) powder with small grain size is the subject of this study. Starting materials are sulphates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3Al5O12), the pH during flocculation

  7. Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

    Energy Technology Data Exchange (ETDEWEB)

    Moe, J [Oslo Univ. (Norway)

    1996-01-01

    The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

  8. Nanosized f.c.c. thallium inclusions in aluminium

    International Nuclear Information System (INIS)

    Johnson, E.; Johansen, A.; Thoft, N.B.; Andersen, H.H.; Sarholt-Kristensen, L.

    1993-01-01

    Ion implantation of pure aluminium with thallium induces the formation of nanosized crystalline inclusions of thallium with a f.c.c. structure. The size of the inclusions depends on the implantation conditions and subsequent annealing treatments and is typically in the range from 1 to 10 nm. The inclusions are aligned topotactically with the aluminium matrix with a cube-cube orientation relationship and they have a truncated octahedral shape bounded by {111} and {001} planes. The lattice parameter of the f.c.c. thallium inclusions is 0.484 ± 0.002 nm, which is slightly but significantly larger than in the high-pressure f.c.c. thallium phase known to be stable above 3.8 GPa. (Author)

  9. Aluminium in foodstuffs and diets in Sweden.

    Science.gov (United States)

    Jorhem, L; Haegglund, G

    1992-01-01

    The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources.

  10. P. J. N. Smal, Die Universalisme in die Psalms. Academisch ...

    African Journals Online (AJOL)

    Test

    dat die historiese element in Israel se Godsopenbaring en daarmee die insig in sy betekenis te kort gedoen word. Die betekenis van die studie vir die historia revelationis is daardeur gering; as duidelike „tydlose” sistematisering van Outestamentiese gegewens oor die betrokke onder- werpe, soos die laaste hoofstuk, bl.

  11. DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE HUIDIGE ...

    African Journals Online (AJOL)

    Test

    DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE. HUIDIGE SITUASIE. Sending is 'n deel van die vervulling van die apostoliese opdrag van die kerk. Dit geskied op grond van en in gehoorsaamheid aan Gods. \\C'oord. Teologiese besinning is daarom die eerste en grondliggende vereiste by die ontwerp van 'n ...

  12. Residual stress development and relief in high strength aluminium alloys using standard and retrogression thermal treatments

    OpenAIRE

    Robinson, J.S; Tanner, D.A

    2003-01-01

    peer-reviewed Residual stresses develop in the aluminium alloy 7010 when the material is quenched from the solution heat treatment temperature. Residual stress measurements have been made using the X-ray diffraction technique and a longitudinal split sawcut method to determine the magnitude of residual stress that develops in specimens sectioned from large open die forgings as a result of (a) quenching these specimens into water at different temperatures, and (b) cold water quenching from ...

  13. DIE PLEK VAN SANG EN MUSIEK IN DIE PROTESTANTSE ...

    African Journals Online (AJOL)

    Test

    Sy moet hierdie opdrag uitvoer deur mid del van die Prediking d.w.s. deur middel van die Woord-vorm, maar ook deur die bediening van die sakramente, dws. deur middel van die vorm van die Daad. Maar nou wil God nie hê dat die Kerk slegs één maal die Evangelie sal predik en die mense sal doop om hulle daarna.

  14. Rapid die manufacturing using direct laser metal deposition

    CSIR Research Space (South Africa)

    Pereira, MFVT

    2009-01-01

    Full Text Available This paper highlights the work undertaken at the CSIR on the issue of rapid die manufacturing through the application and evaluation of a rapid prototyping technique and coating technologies applied to die components of a high pressure casting die...

  15. Packaged die heater

    Science.gov (United States)

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  16. Die radio in Afrika

    Directory of Open Access Journals (Sweden)

    S. de Villiers

    1966-03-01

    Full Text Available Omvang van radio-uitsendings in en na Afrika. — Redes vir die versnelde tempo van uitbreiding. — Radio as die geskikste massa-kommunikasiemiddel vir Afrika. — Faktore wat die verspreiding bemoeilik. — Skouspelagtige toename in luistertalle.Toe Plinius, wat in die jaar 79 oorlede is, in sy „Historia Naturalis” verklaar het dat daar altyd iets nuuts uit Afrika afkomstig is, kon hy nouliks voorsien het dat die „iets" negentien eeue later in die lug sou setel wat hierdie reuse-vasteland oorspan — ’n Babelse spraakverwarring en ’n ongekende, verbete woorde-oorlog in die etergolwe, onder meer daarop bereken om die harte en hoofde van derduisendes te verower.

  17. Die Erfindung des Manuskripts

    DEFF Research Database (Denmark)

    Benne, Christian

    Die Entstehung der literarischen Moderne ging seit dem 18. Jahrhundert damit einher, dass die Anzahl literarischer Manuskripte ebenso wuchs wie deren Bedeutung. Der Buchdruck hatte die Handschrift keineswegs überflüssig gemacht, sondern provozierte im Gegenteil einen neuen, am Autographen...

  18. Characterization and modification of powders used to make aluminium-based metal foams

    OpenAIRE

    Jiménez, Catalina Elena

    2010-01-01

    Metallschäume auf Aluminium-Basis nach dem pulvermetallurgischen Verfahren stellen den Rahmen und die zwei Zielsetzungen dieser Arbeit dar. Die Herstellungsmethode besteht darin, zunächst ein Treibmittel, üblicherweise 0,5 1,0 Gew.% voroxidiertes TiH2, mit Aluminiumpulver oder einer Aluminiumpulverlegierung zu vermischen. Dieses Gemisch wird dann zu einem schäumbaren Halbzeug heißverdichtet und im nächsten Schritt erneut erwärmt und somit aufgeschäumt. Das erste Ziel der Dissertation ist es h...

  19. Die begrafnisdíens

    African Journals Online (AJOL)

    Num 20: 1; Jos 24: 30; Hand 5: 5 - 11). Selfs van die ... Gebruike rondom die begrafnis het van geslag tot geslag gewissel. De Vaux ... der geskied deur die hoorders 'te onderrig, te vermaan, te vertroos en te bestraf, soos dit in elke geval ..... gehandhaaf hoef te word, veral in die lig van die feit dat die predikant die kerklike.

  20. Die gebruik van parallelplaatreologie vir die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat

    Directory of Open Access Journals (Sweden)

    O. C. Vorster

    2005-09-01

    Full Text Available Die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat word bemoeilik deur die feit dat daar tans slegs twee metodes in gebruik is. In die eerste metode word die bepaling deur middel van oplossingsviskometrie gedoen, maar die toksisiteit van die oplosmiddel, asook die tydperk wat dit neem om die bepaling te doen, is ’n probleem. Die tweede metode word beperk deur die kompleksiteit en beskikbaarheid van die apparatuur in Suid-Afrika. In hierdie studie word ’n alternatiewe metode, gebaseer op parallelplaatreologie, voorgestel wat albei hierdie probleme oorkom en die resultate sodoende verkry, word vergelyk met dié wat met bestaande metodes verkry is.

  1. Phase transformation of aluminium hydroxide to aα- alumina prepared from different aluminium salts

    International Nuclear Information System (INIS)

    Masliana Muslimin; Meor Yusoff Meor Sulaiman

    2006-01-01

    The study intends to look at the most suitable aluminium salt to produce a single-phase a-alumina by the hydrothermal method. In the process to produce alumina from the calcination of aluminium hydroxide (Al(OH) 3 ), three different aluminium salts namely aluminium sulfate (Al 2 (SO 4) 2), aluminium nitrate (A(NO 3 ) 3 ) and aluminium chloride (AlCl 3 ) were tried. The process involved the used of NH 4 OH as the precipitating medium. Aluminium hydroxide produced from each of these salts were characterised by x-ray diffraction (XRD) technique to identity the crystalline phase. Aluminium hydroxide produced by all the different aluminium salts is present as boehmite or pseudo-boehmite phase. Aluminium hydroxide produced from Al 2 (SO) 2 , Al(NO) 3 and AlCl 3 shows the transformation of the boehmite phase to a α-alumina phase at 500 0 C. On further heating, the α-alumina continuously formed at 800 o C followed soon at 1000 o C. But for the Al(NO3) 3 salts a different phase transitions occurs on heating especially at 1000 o C. Here it was observed not a single alumina phase is presence but the presence of both α and γ--alumina phases. At 1300 o C, the single α-alumina phase was formed. The study concluded that aluminium sulphate is recommended in order to obtain a single-phase α-alumina with the required characteristics. (Author)

  2. Die invloed van die neo-marxistiese kultuuranalise op die Wêreldraad van Kerke en die Gereformeerde Kerke van Nederland

    Directory of Open Access Journals (Sweden)

    J. M. Vorster

    1979-05-01

    Full Text Available Toe die studente dwarsoor die VSA en Europa in die laat sestigerjare ’n plotselinge en radikale verset openbaar het teen die bestaande orde, het hulle die deur geopen vir ’n nuwe mededinger om die hart van die Westerse kultuur. Dit is die nou reeds bekende neo-Marxisme. Sedertdien het hierdie jongeling sy voetspore op vele vlakke van die Westerse kultuur gelaat.

  3. Preparation of aluminium lakes by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Prapai Pradabkham

    2008-07-01

    Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  4. Electron Conditioning of Technical Aluminium Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Le Pimpec, F

    2004-09-02

    The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (= 1.3, value of many pure elements [1]), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

  5. Thermal formation of corundum from aluminium hydroxides ...

    Indian Academy of Sciences (India)

    Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived ...

  6. Characterisation and concentration profile of aluminium during ...

    African Journals Online (AJOL)

    An aluminium(Al) characterisation study was conducted at a surface water treatment plant (Buffalo Pound Water Treatment Plant (BPWTP) in Moose Jaw, Saskatchewan, Canada) to understand better the effect of alum coagulant on various Al fractions. The raw water source for BPWTP is Buffalo Pound Lake water. The Al ...

  7. Thermal formation of corundum from aluminium hydroxides ...

    Indian Academy of Sciences (India)

    Abstract. Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form γ-Al2O3 at ~ 400°C but the formation of α-Al2O3 at 1200°C occurs more readily in the material ...

  8. Rapidly solidified aluminium for optical applications

    NARCIS (Netherlands)

    Gubbels, G.P.H.; Venrooy, B.W.H. van; Bosch, A.J.; Senden, R.

    2008-01-01

    This paper present the results of a diamond turning study of a rapidly solidified aluminium 6061 alloy grade, known as RSA6061. It is shown that this small grain material can be diamond turned to smaller roughness values than standard AA6061 aluminium grades. Also, the results are nearly as good as

  9. Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

    Science.gov (United States)

    Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

    2016-02-01

    Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

  10. Hydrogen diffusion into fatigue cracks of aluminium alloy 6013 in a corrosive environment; Wasserstoffeinlagerung an Ermuedungsrissen der Aluminiumlegierung 6013 unter korrosiver Umgebung

    Energy Technology Data Exchange (ETDEWEB)

    Lenk, Christian Alexander

    2009-08-13

    The author attempted a time-resolved detection of raised hydrogen concentrations in the plastic deformation region of fatigue cracks in an aluminium test piece deformed by cyclic stress in a corrosive environment. Mechanical material parameters like the crack propagation velocity under cyclic stress change dramatically in a corrosive environment. This is assumed to be caused by hydrogen diffusion, but so far there is no method that reliably measures additional hydrogen from the corrosive environment. For this reason, a special analytical configuration was set up which makes use of the thermal desorption method. First, chips with a thickness of about 20 micrometers are sawed out of the test specimen in high-vacuum conditions. The chips fall into a hot melting vessel in a UHV chamber, where the hydrogen contained in the chips is released. The resulting pressure increase is recorded by a mass spectrometer. A hydrogen profile of the test specimen is obtained by assigning the chip position to the signal. For the corrosive medium in which the test specimen is immersed during crack initiation, i.e. NaCl solution, heavy water was used. This makes it possible to distinguish between the hydrogen contained in a piece of technical aluminium alloy (AA6013) and the deuterium diffusing in from the corrosive fluid. The deuterium is found exclusively in the test piece volume in the strongly plastically deformed region surrounding the fatigue crack. (orig.) [German] Das Ziel der vorliegenden Arbeit besteht im ortsaufgeloesten Nachweis einer erhoehten Wasserstoffkonzentration im plastisch deformierten Bereich von Ermuedungsrissen einer unter korrosiver Umgebung zyklisch verformten Aluminiumprobe. Mechanische Materialparameter wie z.B. die Rissausbreitungsgeschwindigkeit unter zyklischer Belastung aendern sich drastisch in korrosiver Umgebung. Als Ursache fuer dieses Verhalten wird eine Eindiffusion von Wasserstoff vermutet, jedoch gibt es bisher keine Messung die den zusaetzlichen

  11. die pers as bron oor die geskiedenis van die eerste vrydeidsoorlog

    African Journals Online (AJOL)

    dood agv wonde wat hy tydens die slag opgedoen het. Dit was vir die Britse volk onaanvaarbaar dat slegs twee Boere gedood is nadat daar tussen. 20 000 en 30 000 rondtes op die Boere afgevuur is. Die pers kon net nie die ware syfers publiseer nie, want dit sou na 'n onwaarheid Iyk. Het die. Britse volk egter die Boere ...

  12. die impak van metodologie op die verstaan van die nuwe testament

    African Journals Online (AJOL)

    voorbeeld eers een maal deur die bril van die vorm- en redaksiekritiek na die Evangelies gekyk het, dink jy vir altyd anders oor hulle tot- standkoming. Inderdaad, nuwe metodes lei tot nuwe perspektiewe! Dit is dan ook waar die fokus van hierdie artikel val: die impak van metodologie op die verstaan van die Nuwe ...

  13. Verskuiwing in die moraal?

    Directory of Open Access Journals (Sweden)

    S.P. van der Walt

    1974-03-01

    Full Text Available Modewoorde het ons deesdae oorgenoeg in die Christelike sedeleer en hulle kan nogal verwarring stig. U moet my vergun om met u te spreek oor een so ’n modewoord nl „verskuiwing’’ in die moraal. Dis nogal ’n mooi woord, wat so dikwels gebruik word op baie terreine en tog meer wil aandui as maar net ’n veranderde sienswyse, ’n wysiging in opvattinge of nuwe riglyne wat al gangbaar geword het in die praktyk. Die begrip wil eintlik die ewolusionêre gang beklemtoon, want dit is dan eintlik net die ou norme wat effens anders bekyk word of nie meer so nou geneem of dik onderstreep word nie. Die verskuiwing beteken dan dat alles nog dieselfde bly, net die posisie of plek het verander. Verskuiwing beteken tog plekverandering of plekwisseling en dan sekerlik nie in die sin dat die plekke ver uitmekaar lê nie. Verskuiwing beteken net maar vlak langs die vorige te staan kom. As dit dan ’n beter plek is, is dit ewolusie, ontwikkeling, verbetering.

  14. Steam generated conversion coating on aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed...... into functional conversion coatings in order to enhance corrosion resistance and adhesion to paint systems. Chromium based conversion coatings have been extensively used on aluminium alloys to improve adhesion of subsequent paint layers and corrosion resistance. However, the use of hexavalent chromium is strictly...... regulated due to its toxic nature and suspected carcinogenicity. So, it is highly imperative to develop other alternatives for chrome conversion coatings. Treatment of aluminium with natural water at elevated temperatures results in the formation of different forms of aluminium oxide (γ-AlO(OH) , Al(OH)3...

  15. Recent developments in advanced aircraft aluminium alloys

    International Nuclear Information System (INIS)

    Dursun, Tolga; Soutis, Costas

    2014-01-01

    Highlights: • To compete with composites, performance of aluminium alloys should be increased. • Al–Li alloys have higher strength, fracture and fatigue/corrosion resistance. • Improvements of aerospace Al alloys are due to optimised solute content and ratios. • In selecting new materials, there should be no reduction in the level of safety. • The use of hybrid materials could provide additional opportunities for Al alloys. - Abstract: Aluminium alloys have been the primary material for the structural parts of aircraft for more than 80 years because of their well known performance, well established design methods, manufacturing and reliable inspection techniques. Nearly for a decade composites have started to be used more widely in large commercial jet airliners for the fuselage, wing as well as other structural components in place of aluminium alloys due their high specific properties, reduced weight, fatigue performance and corrosion resistance. Although the increased use of composite materials reduced the role of aluminium up to some extent, high strength aluminium alloys remain important in airframe construction. Aluminium is a relatively low cost, light weight metal that can be heat treated and loaded to relatively high level of stresses, and it is one of the most easily produced of the high performance materials, which results in lower manufacturing and maintenance costs. There have been important recent advances in aluminium aircraft alloys that can effectively compete with modern composite materials. This study covers latest developments in enhanced mechanical properties of aluminium alloys, and high performance joining techniques. The mechanical properties on newly developed 2000, 7000 series aluminium alloys and new generation Al–Li alloys are compared with the traditional aluminium alloys. The advantages and disadvantages of the joining methods, laser beam welding and friction stir welding, are also discussed

  16. oor die inhoud en boodskap van die heidelbergse kategismus

    African Journals Online (AJOL)

    Smit. Oor die Inhoud en Boodskap van die Heidelbergse Kategismus. 52. Uiteraard sal dié tema saamhang met die bedoelinge agter die opstel van die Kategismus. Ook die vraag na moontlike bedoelinge of motiewe is egter 'n ingewikkelder vraag as wat miskien gedink mag word. Uiteraard was daar agter elke kategismus ...

  17. Thomas Erastus oor die struktuur van die gemeenskap'^

    African Journals Online (AJOL)

    óók aansprake en regte het, is die opvatting dat sowel die burgerlike gemeenskap as die kerk 'n perfecta societas sibi sufficiens is, nié werklik aanvaar nie. Die Middeleeuse gemeenskap was die corpus christianum,. 'n gemeenskap wat nie deur fisiese of politieke grense beperk was nie. Sy grense het gelê waar die grense ...

  18. die doel en wese van opvoedende onderwys en die implikasies

    African Journals Online (AJOL)

    Oaar moet onderskei word tussen die doelstellings van opvoedende onderwys en die einddoel wat bereik word deur die nastrewing van hierdie doelstellings. Gunter praat van die naderliggende doelstellings (1981, b1.105). \\/at die enddoel van opvoedende onderwys bet ref, gaan die meeste opvoedkundi ges akkoord dat ...

  19. Method for aluminium dross utilization

    International Nuclear Information System (INIS)

    Lucheva, B.; Petkov, R.; Tzonev, Tz.

    2003-01-01

    A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

  20. Tensile Strength and Hardness Correlations with Microscopy in Friction welded Aluminium to Copper

    Science.gov (United States)

    Satish, Rengarajan; Seshagiri Rao, Vaddi; Ananthapadmanaban, Dattaguru; Ravi, Balappa

    2016-01-01

    Aluminium and copper are good conductors of heat and electricity, copper being the better conductor, is a costly metal indeed. On the other hand, aluminium is cheap, easily available and also has a lower density than copper. Hence, worldwide efforts are being made to partially replace copper wire. Solid state welding should be used to join aluminium to copper. This is because the use of fusion welding results in brittle phases formed in the weld interface. One of the solid state welding techniques used for joining aluminium to copper is friction welding. In this paper, an attempt has been made to join aluminium to copper by friction welding by varying the friction welding parameters, namely friction pressure, upset pressure, burn-off length and speed of rotation of the workpiece. Nine different friction welding parameter combinations were used during welding in accordance with ASTM standards and results have been reported. Tensile strength and hardness tests were carried out for each parameter combination. Optimum friction welding parameter combination was identified with respect to tensile strength. Scanning Electron Microscopy and Electron dispersive spectroanalysis were obtained to identify modes of fracture and presence of intermetallic phases for each friction welding combination with the aim to narrow down friction welding parameters that give good properties on the whole.

  1. Die tug oor ampsdraers tydens die doleansie van 1886

    Directory of Open Access Journals (Sweden)

    J. Visser

    1986-06-01

    Full Text Available In art 29 van die Nederlandse Geloofsbelydenis word bely: “Die merktekens om die ware Kerk te ken is die volgende: As die Kerk die suiwere prediking van die evangelie uitoefen, as dit die suiwer bediening van die sakramente gebruik soos Christus dit ingestel het, as die kerklike tug gebruik word om die sondes te straf.” Dit spreek vanself dat wanneer ampsdraers, aan wie Christus sy kudde toevertrou het (Hand 20 : 28, met leer en /of lewenswandel in sonde volhard en nie daarin met tug gestuit word nie, word die ware kerk nie gebou nie maar afgebreek. 0ns sal later in hierdie artikel aantoon hoedanig die suiwer tug oor ampsdraers, veral leertug, tydens die Doleansie tot skade van die kerk van Christus agterweë gebly het.

  2. Variation in aluminium patch test reactivity over time.

    Science.gov (United States)

    Siemund, Ingrid; Mowitz, Martin; Zimerson, Erik; Bruze, Magnus; Hindsén, Monica

    2017-11-01

    Contact allergy to aluminium has been reported more frequently in recent years. It has been pointed out that positive patch test reactions to aluminium may not be reproducible on retesting. To investigate possible variations in patch test reactivity to aluminium over time. Twenty-one adults, who had previously reacted positively to aluminium, were patch tested with equimolar dilution series in pet. of aluminium chloride hexahydrate and aluminium lactate, four times over a period of 8 months. Thirty-six of 84 (43%) serial dilution tests with aluminium chloride hexahydrate and 49 of 84 (58%) serial dilution tests with aluminium lactate gave negative results. The range of reactivity varied between a negative reaction to aluminium chloride hexahydrate at 10% and/or to aluminium lactate at 12%, and a positive reaction to aluminium chloride hexahydrate at 0.1% and/or to aluminium lactate at 0.12%. The highest individual difference in test reactivity noticed was 320-fold when the two most divergent minimal eliciting concentrations were compared. The patch test reactivity to aluminium varies over time. Aluminium-allergic individuals may have false-negative reactions. Therefore, retesting with aluminium should be considered when there is a strong suspicion of aluminium contact allergy. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  3. Die metafoor by Breyten Breytenbach

    African Journals Online (AJOL)

    Owner

    23 Jun 2009 ... metafories, of spesifiek verwysend, te werk gegaan is. Tyd sou mens die hoofmotief van die bundel noem, tyd en geheue wat verbygaan: 1 en 2; en die einde van die storie wat gekom het: “fluit-fluit my storie is uit”. (Die tema van verbygaan word weer opgeneem in 8 en 9: die stories wat nooit meer gehoor ...

  4. IRAN IN DIE INTERNASIONALE MAGSTRYD

    African Journals Online (AJOL)

    In die verband kan genoem word dat die Russe nog grotendeels gebruik maak van 'n metode waarvolgens water in die oliestratum gepomp word om 'n opwaartse druk van ru-olie te verseker; een nadeel hiervan is dat die water mettertyd deur die oliehoudende laag ontsnap en agv die drukverlies isvoortgesette ontginning.

  5. Die singulation method

    Science.gov (United States)

    Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

    2013-06-11

    A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

  6. Electron beam welding of aluminium components

    International Nuclear Information System (INIS)

    Maajid, Ali; Vadali, S.K.; Maury, D.K.

    2015-01-01

    Aluminium is one of the most widely used materials in industries like transportation, shipbuilding, manufacturing, aerospace, nuclear, etc. The challenges in joining of aluminium are distortion, cleanliness and quality. Main difficulties faced during fusion welding of aluminium components are removal of surface oxide layer, weld porosity, high heat input requirement, distortion, hot cracking, etc. Physical properties of aluminium such as its high thermal conductivity, high coefficient of thermal expansion, no change in colour at high temperature, large difference in the melting points of the metal and its oxide (∼ 1400 °C) compound the difficulties faced during welding. Gas Tungsten Arc Welding (GTAW), Gas Metal Arc Welding (GMAW), Plasma Arc Welding (PAW), etc are generally used in industries for fusion welding of aluminium alloys. However in case of thicker jobs the above processes are not suitable due to requirements of elaborate edge preparation, preheating of jobs, fixturing to prevent distortion, etc. Moreover, precise control over the heat input during welding and weld bead penetration is not possible with above processes. Further, if heat sensitive parts are located near the weld joint then high energy density beam welding process like Electron Beam Welding (EBW) is the best possible choice for aluminium welding.This paper discusses EB welding of aluminium components, typical geometry of components, selection/optimization of welding parameters, problems faced during standardization of welding and process parameters and their remedies etc.

  7. Alveolar proteinosis associated with aluminium dust inhalation.

    Science.gov (United States)

    Chew, R; Nigam, S; Sivakumaran, P

    2016-08-01

    Secondary alveolar proteinosis is a rare lung disease which may be triggered by a variety of inhaled particles. The diagnosis is made by detection of anti-granulocyte-macrophage colony-stimulating factor antibodies in bronchoalveolar lavage fluid, which appears milky white and contains lamellar bodies. Aluminium has been suggested as a possible cause, but there is little evidence in the literature to support this assertion. We report the case of a 46-year-old former boilermaker and boat builder who developed secondary alveolar proteinosis following sustained heavy aluminium exposure. The presence of aluminium was confirmed both by histological examination and metallurgical analysis of a mediastinal lymph node. Despite cessation of exposure to aluminium and treatment with whole-lung lavage which normally results in improvements in both symptoms and lung function, the outcome was poor and novel therapies are now being used for this patient. It may be that the natural history in aluminium-related alveolar proteinosis is different, with the metal playing a mediating role in the disease process. Our case further supports the link between aluminium and secondary alveolar proteinosis and highlights the need for measures to prevent excessive aluminium inhalation in relevant industries. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  8. Ontsporing van die regstaatsbegrip en sy konsekwensies vir die afrikanervolk

    Directory of Open Access Journals (Sweden)

    N. G.S. Van der Walt

    1966-03-01

    Full Text Available Die opvatting van die suiwere regstaat bring sy vraagstukke mee wanneer dit in verband gebring word met die leer van die soewereiniteit in eie kring. Laasgenoemde leer wortel in die geloof dat God die mens roep tot diens aan Hom, en dat die mens vry moet wees om ten opsigte van alle lewensaspekte God na die hoogste mate te kan dien. Hierdie verskeidenheid van aspekte is deur dr. A. Kuyper en sy volgelinge gesistemati- seer tot menslike verbande en lewenskringe, elk met ’n be- paalde sfeer waarin ander kringe nie mag inmeng nie. Elkeen is dan soewerein binne sy eie kring. Met verwysing na die staat is dan gespreek van die staatstaak as synde die hand- hawing van die reg, en omdat die staat in toenemende mate hom veral in die latere tyd ook besig gehou het met bedrywig- hede wat nouliks as van juridiese aard beskou kan word, is daar die onderskeid gemaak tussen die primêre en sekundêre taak van die staat. Die sistematiek van die wetsidee, deur prof. Dooyeweerd ontwikkel, waar die staat sy bestemmingsfunksie in die regsaspek vind, het vanselfsprekend geen plek vir so 'n dualistiese staatstaak nie, en die oplossing is deur sommige daarin gesoek om sulke staatsoptrede te vertolk as hebbende wel betrekking op die regsgemeenskap of die regsverkeer. Staatsondernemings soos paaie, spoorweë, spellingreëling, ens. word dan beskou as noodsaaklik vir die instandhouding van die regsgemeenskap en regsverkeer. Tereg wys A. M. Donner1 daarop dat so ’n vertolking eintlik neerkom op ’n oorspanning van die regsbegrip. Hy self sien dan die staatstaak in vrede- of orde-handhawing, wat in die eerste plaas wel regshandha- wing veronderstel. Onder orde word dan alles verstaan wat noodsaaklik is vir die gladde verkeer in die ontwikkelingsgang van die regsgemeenskap. Die wese van die staat het dan vol- gens hom te doen met reg, maar sy taak is meer as suiwere regshandhawing. Wat onrus verwek en die orde versteur, moet uit die openbare lewe verwyder word, en die

  9. Challenges in LCA modelling of multiple loops for aluminium cans

    DEFF Research Database (Denmark)

    Niero, Monia; Olsen, Stig Irving

    considered the case of closed-loop recycling for aluminium cans, where body and lid are different alloys, and discussed the abovementioned challenge. The Life Cycle Inventory (LCI) modelling of aluminium processes is traditionally based on a pure aluminium flow, therefore neglecting the presence of alloying...... elements. We included the effect of alloying elements on the LCA modelling of aluminium can recycling. First, we performed a mass balance of the main alloying elements (Mn, Fe, Si, Cu) in aluminium can recycling at increasing levels of recycling rate. The analysis distinguished between different aluminium...... packaging scrap sources (i.e. used beverage can and mixed aluminium packaging) to understand the limiting factors for multiple loop aluminium can recycling. Secondly, we performed a comparative LCA of aluminium can production and recycling in multiple loops considering the two aluminium packaging scrap...

  10. Die sterwende kindjie

    Directory of Open Access Journals (Sweden)

    J.T. De Jongh van Arkel

    1983-09-01

    Full Text Available The thought of a child dying appears as an antithesis and thus the feelings evoked by the dying child are stronger than when older persons are dying. Around the child’s death bed there is no place for detached spectators and all become involved in caring for and supporting him. Caregivers also have a supporting responsibility towards the members of the child’s family.

  11. THE COSTS OF THE ELECTRICAL ENERGY IN THE ALUMINIUM INDUSTRY

    Directory of Open Access Journals (Sweden)

    Cilianu Marian

    2012-07-01

    Full Text Available The economic crisis has given the opportunity to reconsider the use of resources, so the subject of competitive advantage has become actual. In the aluminium industry the cost of electrical energy is critical not only for competitive reasons but for the mere existence and performance of numerous production facilities . Several ways of resisting the pressure of high energy costs have been experimented the most promising being those based on different forms of public-private partnership/co-operation. In many countries the big industrial producers benefit from a special treatment concerning the energy acquisition and are supported by the government in order to remain competitive.

  12. Physical, morphological and rheological alterations of properties by the calcination of aluminium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Pandolfelli, V C; Varela, J A; Longo, E

    1987-03-01

    Evolution of physical, morphological and rheological characteristics resulted from several thermal treatments on national aluminium hydroxide, are evaluated and discussed after mercury porosimetry analysis, scanning electron microscopy, surface area and pressure curve compaction. The results may consider about the Kinetics of the reaction during the aglomerate calcination and to verify the better processing conditions to get products with superior performance. (Autor).

  13. Analise van die Tswanaraaisel

    Directory of Open Access Journals (Sweden)

    S. A. Swanepoel

    1984-05-01

    Full Text Available ’n Strukturele, stilistiese en funksionele bcskrywing van die Twanaraaisel bring mee dat daar aan die volgende aspekte aandag gegee moet word: •\tWat is ’n raaisel en lioe word dit in Tswana genoem. •\tTot watter studiegebied en literere genre hoort die raaisel en watter subvorme kan vir Tswana onderskei word. •\tHoe sien die struktuur van Tswanaraaisels daar uit. •\tDeur wie, waar, wanneer en hoe word Tswanaraaisels voorgedra. •\tWatter stilistiese kenmcrke kan in Tswanaraaisels onderskei word. •\tWatter funksies vervul raaisels in ’n Tswanagcmeenskap.

  14. The Angry Dying Patient.

    Science.gov (United States)

    Houston, Robert E.

    1999-02-01

    Over 25 years ago, Kubler-Ross identified anger as a predictable part of the dying process. When the dying patient becomes angry in the clinical setting, all types of communication become strained. Physicians can help the angry dying patient through this difficult time by using 10 rules of engagement. When physicians engage and empathize with these patients, they improve the patient's response to pain and they reduce patient suffering. When physicians educate patients on their normal responses to dying and enlist them in the process of family reconciliation, they can impact the end-of-life experience in a positive way.

  15. Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

    Science.gov (United States)

    Grove, C. A.; Judd, G.; Ansell, G. S.

    1972-01-01

    Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

  16. Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates

    International Nuclear Information System (INIS)

    Chekhonin, Paul; Beausir, Benoît; Scharnweber, Juliane; Oertel, Carl-Georg; Hausöl, Tina; Höppel, Heinz Werner; Brokmeier, Heinz-Günter; Skrotzki, Werner

    2012-01-01

    Aluminium laminates consisting of high-purity aluminium and commercially pure aluminium have been produced by accumulative roll bonding (ARB) at ambient temperature for up to 10 cycles. To study the microstructure and texture development of the high-purity aluminium layers with regard to the shrinking layer thickness during ARB, microstructure and texture investigations were carried out by electron backscatter diffraction and neutron and X-ray diffraction, respectively. While the commercially pure aluminium layers develop an ultrafine-grained microstructure, partial discontinuous recrystallization occurs in the high-purity layers. The texture of the high-purity layers mainly consists of Cube and “Tilted Cube” (tilted with respect to the transverse direction) components. The experimental results are discussed with respect to confined recrystallization in the ARB aluminium laminates.

  17. Experimental investigation on the performance of an improved equal channel angular pressing die

    International Nuclear Information System (INIS)

    Surendarnath, S; Sankaranarayanasamy, K; Ravisankar, B

    2014-01-01

    A major problem in Equal Channel Angular Pressing is die design. Friction plays an important role in the extrusion process. In the present work, Aluminium 6082 alloy was processed through a modified ECAP die originally proposed by Mathieu et al. in 2004 [1] and the performance of the die was analyzed. The channel angle was φ=90° and corner angle ψ=20°. Mechanical properties, micro hardness measurement and crystalline size (D) were measured from the extruded specimen for both the conventional and new die designs. It has been found that the new die samples displayed better results than the conventional ones. The newly designed die reduced the effect of friction on the work piece, it increased the tensile strength, the hardness of the material and achieved better grain refinement

  18. Die brein soos beskou deur die Grieke en Romeine

    Directory of Open Access Journals (Sweden)

    Francois P. Retief

    2015-02-01

    Full Text Available In Ou Egipte is mummifikasie met uitgebreide reseksie of uitsnyding van organe geassosieer, maar geen kennis is geneem van die morfologie van die brein nie. Griekse skrywers van die sesde en vyfde eeue v.C. het die brein aanvanklik gesien as die setel van intelligensie, die orgaan van sensoriese waarneming en gedeeltelik die oorsprong van sperma. Pneuma het ’n belangrike rol in breinfunksie gespeel. Hippokrates was die eerste om die brein te beskryf as ’n dubbele orgaan, wat met harsingvlies (meninges bedek, funksioneel van pneuma afhanklik en vertolker van begrip is. Tydgenote soos Plato, Aristoteles en Diokles het tot die beskrywing bygedra, maar laasgenoemde twee het beweer dat die hart die middelpunt van intelligensie is en nie die brein nie. Gedurende die laaste helfte van die vierde eeu v.C. is disseksie van die menslike liggaam tydelik aan die mediese skool van Alexandrië toegelaat en het dit tot merkwaardige vooruitgang in die begrip van die menslike anatomie en fisiologie gelei. Herofilus en Erasistratus het uitstekende beskrywings van die struktuur en funksie van die brein gegee wat eers in die tweede eeu n.C. deur Galenus geëwenaar is.

  19. Niobium-base grain refiner for aluminium

    International Nuclear Information System (INIS)

    Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

    1980-01-01

    A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

  20. Net shape powder processing of aluminium

    International Nuclear Information System (INIS)

    Schaffer, G.B.

    2000-01-01

    The increasing interest in light weight materials coupled to the need for cost-effective processing have combined to create a significant opportunity for aluminium powder metallurgy. Net shape processing of aluminium using the classical press-and-sinter powder metallurgy technique is a unique and important metal-forming method which is cost effective in producing complex parts at, or very close to, final dimensions. This paper provides an overview of the net shape powder processing of aluminium. Current research is critically reviewed and the future potential is briefly considered

  1. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid

    2014-01-01

    -life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition...... of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...

  2. DIE SUID-AFRIKAANSE JEUG IN VOORTREKKERTYDPERK

    African Journals Online (AJOL)

    dien. Die planke en velie moes keer dat die assegaaie die mense tref. Voor die geveg het die vrouens en groter dogters koeels gegiet. Tydens die geveg het die seuns gehelp skiet terwyl die vrouens en dogters die gewere vir die mans gelaai het. Van die dogters soos Nellie. Botha (11 jaar oud) en haar sussie Fya (15 jaar.

  3. Die uitbouing van die Bybelse kanon in antieke Judaïsme en die ...

    African Journals Online (AJOL)

    31 Jul 2015 ... die oer-Christelike boodskap tot by sy Ou Testamentiese wortels, die geskrifte van Israel wat cum grano salis die 'Bybel' van die oer-Christendom geword het en die blywende verwysingspunt van die Christelike boodskap is. Erkenning. Hierdie artikel is vertaal na Afrikaans deur Prof. Jan G. van der Watt.

  4. Die opleiding van bedryfsielkundiges aan die universiteit van Fort Hare

    Directory of Open Access Journals (Sweden)

    W. Botha

    1977-11-01

    Full Text Available Die Departement Bedryfsielkunde aan die Universiteit van Fort Hare is 'n relatiewe jong departement en het eers in 1965 tot stand gekom. Voor hierdie datum is Bedryfsielkunde as 'n kort kursus deur die departement van suiwer Sielkunde aangebied en een van die destydse dosente, Dr. W. Backer, het die inisiatief geneem om 'n selfstandige departement van Bedryfsielkunde in die Fakulteit van Ekonomiese Wetenskappe op die been te bring.

  5. Aluminium Toxicity Targets in Plants

    Directory of Open Access Journals (Sweden)

    Sónia Silva

    2012-01-01

    Full Text Available Aluminium (Al is the third most abundant metallic element in soil but becomes available to plants only when the soil pH drops below 5.5. At those conditions, plants present several signals of Al toxicity. As reported by literature, major consequences of Al exposure are the decrease of plant production and the inhibition of root growth. The root growth inhibition may be directly/indirectly responsible for the loss of plant production. In this paper the most remarkable symptoms of Al toxicity in plants and the latest findings in this area are addressed. Root growth inhibition, ROS production, alterations on root cell wall and plasma membrane, nutrient unbalances, callose accumulation, and disturbance of cytoplasmic Ca2+ homeostasis, among other signals of Al toxicity are discussed, and, when possible, the behavior of Al-tolerant versus Al-sensitive genotypes under Al is compared.

  6. Bonding of aluminium matrix composites for application in the transport industry

    International Nuclear Information System (INIS)

    Urena, A.; Gomez de Salazar, J.M.

    1993-01-01

    A discontinuously reinforced MMC containing 12 vol % SiC particles in an Al-Cu-Mg alloy (AA 2124) matrix has been diffusion bonded. Thick interlayers of different superplastic aluminium alloys (Al-Li 8090 and Al-Cu SUPRAL) were used to reduce the bonding pressure and ensure complete surface contact. Microstructural studies shown higher continuity in joints bonded with 8090 interlayer than with other alloys. Precipitation of rich-copper intermetallic was detected, after bonding, in the interlayer because diffusion of Cu from 2124 matrix. Results suggest that Li contained in the interlayer favours the partial disruption of the aluminium oxide film, making easier the solid state bonding. (orig.)

  7. Oor die Bybel in die Afrikaanse digkuns

    African Journals Online (AJOL)

    another. As a matter of fact, the development of Afri kaans, the instrument of the poet, has been significantly influenced the Afrikaans translation of the Bible. Belie ... ook gesê het: Saam met ons literatuur, so oud as hy is. Die eerste Afrikaanse digter by wie ons omvattende Bybelse invloed kry, is. Totius, een van ons vroegste ...

  8. Aluminium fumarate and CPO-27(Ni) MOFs: Characterization and thermodynamic analysis for adsorption heat pump applications

    International Nuclear Information System (INIS)

    Elsayed, Eman; AL-Dadah, Raya; Mahmoud, Saad; Elsayed, Ahmed; Anderson, Paul A.

    2016-01-01

    Highlights: • CPO-27(Ni) and aluminium fumarate were investigated for adsorption heating, cooling and desalination applications. • Both MOFs have high potential in adsorption applications. • The optimum desorption temperature for the CPO-27(Ni) is higher than 90 °C, and for aluminium fumarate, it is 55–70 °C. • CPO-27(Ni) outperforms aluminium fumarate at low evaporation temperature (5 °C). • Aluminium fumarate outperforms CPO-27(Ni) at high evaporation temperature (20 °C). - Abstract: Metal-organic framework (MOF) materials are new porous materials with high surface area, pore size and volume, and tunable pore geometry thus providing high adsorption capacity. Currently, limited MOF materials with high water adsorption capabilities and hydrothermal stability are available on a large scale. Two MOF materials, namely CPO-27(Ni) and aluminium fumarate, have been identified to have a high hydrothermal stability, high water uptake of 0.47 g_H_2_O_.g_a_d_s"−"1 and 0.53 g_H_2_O_.g_a_d_s"−"1 at a relative pressure of 0.9 and are commercially available. This work aims to measure the water adsorption characteristics of these two MOF materials in terms of isotherms, kinetics and cyclic stability. Also the thermodynamic cycle performance of such materials based on their equilibrium adsorption data was investigated under different operating conditions for various adsorption applications such as heating, cooling and water desalination. Results showed that the CPO-27(Ni)/water pair outperformed the aluminium fumarate/water pair at low evaporation temperatures (5 °C) and high desorption temperatures (≥90 °C), while the aluminium fumarate/water pair was more suitable for applications requiring high evaporation temperature (20 °C) and/or low desorption temperature (70 °C).

  9. calvyn oor die leiding van die heilige gees in die verklaring van die

    African Journals Online (AJOL)

    Mittel alters, bis er zur Ruhe kommt bei den kanonischen Schriften der. Urzeit der christlichen Ära (Barth ... (ego tamen dimoveri non possum ab amore compendii, CO 10, 403). Deur die boodskap van die .... Idem ergo spiritus qui per os prophetarum loquutus est, in corda nostra penetret necesse est, ut persuadeat fideliter ...

  10. KERKWEES IN DIE

    African Journals Online (AJOL)

    Acta Theologica is an accredited South. African journal publishing ... SciELO South Africa. REDAKSIE/ ... 'n persoon belydenis van geloof af wat instemming met die betrokke kerk se ...... Ek was na my ongeluk buite aksie en op Clarens. 'n Mede-lid ...... Die “formation of new confessions, change to current confessions, and.

  11. Dying with dignity

    OpenAIRE

    S P Kalantri

    2003-01-01

    The concept of dignity has beeen one of the ambiguous concepts in biomedical ethics. Thus the ambiguous nature of this concept has been extended to what it means to die with dignity. This research work is an investigation into the complexity in the understanding of "dying with dignity" in Applied Ethics.

  12. The day Madiba died

    African Journals Online (AJOL)

    8 Apr 2016 ... shibien en ma is nie happy nie. Susan Gaigher se allegoriese fanta- sie- oftewel wetenskapsfiksieverhale. “Martine se teepot” (46–55) en “Maslow”. (56–67) is verfrissend. Gaigher is een van die min skrywers in die bundel wat 'n kenmerkende en oorspronklike stem laat klink. 'n Mens sal 'n Gaigher-verhaal.

  13. Die entwicklung, die metamorphose, die entstehung: Die konzepte des organismus von Aristoteles bis Darwin

    Directory of Open Access Journals (Sweden)

    Kamerer Eva

    2009-01-01

    Full Text Available (nemački In diesem Aufsatz versuche ich, die Elemente verschiedener Konzepte des Organismus in der Philosophie und in der Wissenschaft zu analysieren. Die Deutungen des Organismus und der Einheit der Natur bei Aristoteles, Kant und Goethe werden als ein Beispiel der Bewegung von einem finalistischen zum antifinalistischen Bild der Natur verstanden.

  14. Steam Initiated Surface Modification of Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud

    The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco......, crystalline nano-particles, role of steam-based treatment on adhesion of industrially applied powder coating, and investigations of a failed painted aluminium window profile due to defects in the extruded profile. Chapters 13 and 14 describe the overall discussion, conclusions and future work based...

  15. Irradiation effects in magnesium and aluminium alloys

    International Nuclear Information System (INIS)

    Sturcken, E.F.

    1979-01-01

    Effects of neutron irradiation on microstructure, mechanical properties and swelling of several magnesium and aluminium alloys were studied. The neutron fluences of 2-3 X 10 22 n/cm 2 , >0.2 MeV produced displacement doses of 20 to 45 displacements per atom (dpa). Ductility of the magnesium alloys was severely reduced by irradiation induced recrystallization and precipitation of various forms. Precipitation of transmuted silicon occurred in the aluminium alloys. However, the effect on ductility was much less than for the magnesium alloys. The magnesium and aluminium alloys had excellent resistance to swelling: The best magnesium alloy was Mg/3.0 wt% Al/0.19 wt% Ca; its density decreased by only 0.13%. The best aluminium alloy was 6063, with a density decrease of 0.22%. (Auth.)

  16. COMBINED ALUMINIUM SULFATE/HYDROXIDE PROCESS FOR ...

    African Journals Online (AJOL)

    sulfate, and used for fluoride removal from water by combining with Nalgonda Technique. ... effects on human health and could result in fluorosis. ... [23], nanoscale aluminium oxide hydroxide (AlOOH) [24] and natural zeolite [25], were among.

  17. Aluminium reprocessing with local mineral raw material

    International Nuclear Information System (INIS)

    Mirsaidov, U.M.

    2002-01-01

    With the purpose of utilization of ice sediment, receiving from mud fields solutions and flotation tails and at using local aluminium and fluorine-containing raw material was elaborated fundamental technologic scheme presented in this chapter of book

  18. Deformation features of aluminium in tensile tests

    International Nuclear Information System (INIS)

    Quadros, N.F. de.

    1984-01-01

    It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 400 0 C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.) [pt

  19. Paradigmas en progressie in die teologie: *n Perspektief op die ...

    African Journals Online (AJOL)

    Die metodologie as besinningsterrein word egter al belangriker. Gedurende die tweede week van April 1988 het teoloë van dwarsoor Suid-. Afrika by die nuwe gebou van die Raad vir Geesteswetenskaplike Navorsing in. Pretoria byeen gekom vir 'n kongres van amper drie dae met die tema Paradigma.'> 476. ISSN 0259 ...

  20. die korrelasie tussen die gemiddelde daaglikse toename van ...

    African Journals Online (AJOL)

    'n Regressielyn is uit die gegewens bereken deur 'n beswaarde regressieanaliese en die 80 persent-voorspellings- bande is bepaal. Die punte wat ver buite die normale ver- spreidingsband geval hetkon almal met goeie rede as abnor- maal beskou word (sien tabel 1) en is nie ingesluit by die statistiese berekenings nie.

  1. amp' van die ouderling in die Nuwe Testament

    African Journals Online (AJOL)

    Jesus self het geen kerk gestig nie en daarom, veral omdat die Jesus-beweging inter mums ten opsigte van die Joodse godsdiens van sy tyd tot stand gekom het, het ...... Die klem val dus nie op die npoTCTT0fievo<; se rang of outoriteit nie, maar op sy pastorale funksie in die huishouding of huisgemeente (kyk Reicke.

  2. Silane based coating of aluminium mold

    DEFF Research Database (Denmark)

    2013-01-01

    having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...... of structures which would otherwise be difficult to mold. The resistance of the coated aluminium mold is significantly improved by applying a silane-based coating layer....

  3. Characterization of aluminium alloys rapidly solidified

    International Nuclear Information System (INIS)

    Monteiro, W.A.

    1988-01-01

    This paper discussed the investigation of the microstructural and mechanical properties of the aluminium alloys (3003; 7050; Al-9% Mg) rapidly solidified by melt spinning process (cooling rate 10 4 - 10 6 K/s). The rapidly solidification process of the studied aluminium alloys brought a microcrystallinity, a minimum presence of coarse precipitation and, also, better mechanical properties of them comparing to the same alloys using ingot process. (author) [pt

  4. Speciation analysis of aluminium in plant parts of Betula pendula and in soil.

    Science.gov (United States)

    Zioła-Frankowska, Anetta; Frankowski, Marcin

    2018-03-01

    The research presents the first results of aluminium speciation analysis in aqueous extracts of individual plant parts of Betula pendula and soil samples, using High Performance Ion Chromatography with Diode Array Detection (HPIC-DAD). The applied method allowed us to carry out a full speciation analysis of aluminium in the form of predominant aluminium-fluoride complexes: AlF (x=2,3,4) (3-x) (first analytical signal), AlF 2+ (second analytical signal) and Al 3+ (third analytical signal) in samples of lateral roots, tap roots, twigs, stem, leaf and soil collected under roots of B. pendula. Concentrations of aluminium and its complexes were determined for two types of environment characterised by different degree of human impact: contaminated site of the Chemical Plant in Luboń and protected area of the Wielkopolski National Park. For all the analysed samples of B. pendula and soil, AlF (x=2,3,4) (3-x) had the largest contribution, followed by Al 3+ and AlF 2+ . Significant differences in concentration and contribution of Al-F complexes and Al 3+ form, depending on the place of sampling (different anthropogenic pressure) and plant part of B. pendula were observed. Based on the obtained results, it was found that transport of aluminium is "blocked" by lateral roots, and is closely related to Al content of soil. Copyright © 2017. Published by Elsevier B.V.

  5. Structural evolution in nanoporous anodic aluminium oxide

    International Nuclear Information System (INIS)

    Rocca, Emmanuel; Vantelon, Delphine; Reguer, Solenn; Mirambet, François

    2012-01-01

    Nanoporous and self-organized layers of aluminium alloys are used in many applications as membranes, templates for nanometric objects or corrosion protection for aluminium alloys. The use of this nanometric structure widely remains empirical, especially in the case of very small pores ( 4 into AlO 6 cluster and a partial release of sulphate ions are an important chemical transformation of the amorphous structure. This structural transformation defines the chemistry (pH and surface charge) inside the nanopores, the ageing behaviour and the possible incorporation or diffusion of chemical species in the nanostructure. Highlights: ► Investigations of local chemical environment of aluminium atoms in anodic aluminium oxide. ► The oxide structure is constituted by 2/3 of aluminium in tetrahedral coordination 1/3 in octahedral coordination. ► In contact with water, AlO 4 clusters are transformed into AlO 6 cluster and the aluminium sulphate bonds are hydrolysed. ► These transformations induce a pH decrease inside the nanostructure.

  6. Complex deformation routes for direct recycling aluminium alloy scrap via industrial hot extrusion

    Science.gov (United States)

    Paraskevas, Dimos; Kellens, Karel; Kampen, Carlos; Mohammadi, Amirahmad; Duflou, Joost R.

    2018-05-01

    This paper presents the final results of an industrial project, aiming for direct hot extrusion of wrought aluminium alloy scrap at an industrial scale. Two types of complex deformation/extrusion routes were tested for the production of the same profile, starting from AA6060 scrap in form of machining chips. More specifically scrap-based billets were extruded through: a 2-porthole and a 4-porthole die-set, modified for enhanced scrap consolidation and grain refinement. For comparison reasons, cast billets of the same alloy were extruded through the modified 2-porthole die set. The tensile testing results as well as microstructural investigations show that the 4-porthole extrusion route further improves scrap consolidation compared to the 2-porthole die output. The successful implementation of solid state recycling, directly at industrial level, indicates the technological readiness level of this research.

  7. Die toekoms en ons roeping

    Directory of Open Access Journals (Sweden)

    S. du Toit

    1954-03-01

    Full Text Available Om te weet wat ons roeping in die toekoms sal wees, moet ons eers besef wat in ons eie tyd aan die gang is en langs watter lyne die dinge beweeg. Dit is ons plig om te let op die tekens van die tye in die lig van die profetiese Woord. En dan wil ons dadelik beklemtoon dat ons in Suid-Afrika nie in die waan moet lewe dat ons hier onbekommerd en onaangetas deur die wêreldgebeure ons roeping en bestemming kan uitwerk nie.

  8. Die Hervormde Teologiese Studies na vyftig jaar

    African Journals Online (AJOL)

    INLEIDEND. In die tweede helfte van die jaar 1943 het die Hervormde Teologiese Studies die eerste maal verskyn. Dit was die produk van lang besinning en beplanning. Die dryfkrag agter die totstandkoming was prof dr S P Engeibrecht, 'n man wie se idealisme en toewyding aan die kerk groot dinge vir die kerk en ook die ...

  9. [Aluminium content in foods with aluminium-containing food additives].

    Science.gov (United States)

    Ogimoto, Mami; Suzuki, Kumi; Kabashima, Junichiro; Nakazato, Mitsuo; Uematsu, Yoko

    2012-01-01

    The aluminium (Al) content of 105 samples, including bakery products made with baking powder, agricultural products and seafoods treated with alum, was investigated. The amounts of Al detected were as follows (limit of quantification: 0.01 mg/g): 0.01-0.37 mg/g in 26 of 57 bakery products, 0.22-0.57 mg/g in 3 of 6 powder mixes, 0.01-0.05 mg/g in all three agricultural products examined, 0.03-0.90 mg/g in 4 of 6 seafood samples, 0.01-0.03 mg/g in 3 of 11 samples of instant noodles, 0.04-0.14 mg/g in 3 of 4 samples of vermicelli, 0.01 mg/g in 1 of 16 soybean products, but none in soybeans. Amounts equivalent to the PTWI of a 16 kg infant were detected in two samples of bakery products, two samples of powder mixes and one sample of salted jellyfish, if each sample was taken once a week. These results suggest that certain foods, depending on the product and the intake, might exceed the PTWI of children, especially infants.

  10. Aluminium exclusion and aluminium tolerance in woody plants

    Directory of Open Access Journals (Sweden)

    Ivano eBrunner

    2013-06-01

    Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

  11. Die owerheidsinmenging met betrekking tot kerklike tughandelinge.

    Directory of Open Access Journals (Sweden)

    L. Roeleveld

    1982-06-01

    Full Text Available Volgens art 29 NGB is die merktekens van die ware kerk die suiwere prediking van die Evangelie, die suiwere bediening van die Sakramente en die gebruik van die kerklike tug. Art. 32 NGB spreek uit dat die Kerkorde nie mag afwyk van wat Christus ingestel het nie. Menslike vindinge en wette om die gewetens te bind en te dwing, moet daarom verwerp word. Die ekskommunikasie of die ban moet toegepas word volgens die Woord van God.

  12. Pentateugtradisies in die boek Hosea

    African Journals Online (AJOL)

    om te bepaal of die verwysing na 'n gebeure te doen het met die verre verlede of met die .... Hosea 2:1-2 JHWH se trou aan sy beloftes. ... dat huile na Egipte sal terugkeer. Die presiese bedoeiing van die woorde 'huile sal terugkeer na Egipte' is omstre- de. Kommentatore soos Rudolph meen dat dit verstaan moet word as ...

  13. Die begrafnisdíens

    African Journals Online (AJOL)

    (De Vaux 1961:108). Was die begrafnis 'n familie of 'n kerklike aangeleentheid? Hierdie vraag word nie in die Bybel beantwoord nie. Abraham het sy vrou begrawe (Gen 23: 19-. 20). Isak en Ismael ..... ver gekom om die begrafnis 'n kerklike aangeleentheid te maak nie. Hierdie stap .... trou aan die sorg van God. * Die kerk ...

  14. Metodes in die Christelike etiek

    African Journals Online (AJOL)

    The basic question in Christian ethics is not primarily. 'What should I do?' The basic question is rather ' ... should therefore be accepted as being part of the method used in Christian ethics. 1. INLEIDEND ..... aan die kant van die onderdrukte' verkondig word, word die Christen opgeroep om horn te skaar aan die kant van die ...

  15. Die teologiese skool in die P.U.K vir C.H.O.: met die betekenis van die teologiese skool vir die Christelike wetenskap

    Directory of Open Access Journals (Sweden)

    F. Postma

    1944-03-01

    Full Text Available Die Teologiese Skool van die Gereformeerde Kerk gedink op 29 November 1944 sy vyf-en-sewentigjarige bestaan.Die Raad en Senaat van die P.U.K. vir C.H.O. wil ook langs hierdie weg die Teologiese Skool van harte gelukwens en die versekering gee dat daar by die outoriteite van die P.U.K. ’n diepgevoelde dankbaarheid heers dat hierdie inrigting sovele jare deur onse God en Vader gedra en gespaar is.

  16. TEM investigation of aluminium containing precipitates in high aluminium doped silicon carbide

    International Nuclear Information System (INIS)

    Wong-Leung, J.; FitzGerald, J.D.

    2002-01-01

    Full text: Silicon carbide is a promising semiconductor material for applications in high temperature and high power devices. The successful growth of good quality epilayers in this material has enhanced its potential for device applications. As a novel semiconductor material, there is a need for studying its basic physical properties and the role of dopants in this material. In this study, silicon carbide epilayers were grown on 4H-SiC wafers of (0001) orientation with a miscut angle of 8 deg at a temperature of 1550 deg C. The epilayers contained regions of high aluminium doping well above the solubility of aluminium in silicon carbide. High temperature annealing of this material resulted in the precipitation of aluminium in the wafers. The samples were analysed by secondary ion mass spectrometry and transmission electron microscopy. Selected area diffraction studies show the presence of aluminium carbide and aluminium silicon carbide phases. Copyright (2002) Australian Society for Electron Microscopy Inc

  17. Die Frage nach Gerechtigkeit.

    Directory of Open Access Journals (Sweden)

    Martin Jäggle

    2014-07-01

    Full Text Available ENGLISH: In the first part six stages in the author’s path of life are described, which have influenced his engagement with justice. The second part gives an insight into his religious educational work, in which the issue of justice was especially significant on the example of ‘religion in the context of migration’ and of the ecumenic initiative ‘lebens.werte.schule’ (school worth living. The vision of the Kingdom of God and the necessity of participation become apparent. DEUTSCH: Im ersten Teil werden sechs Stationen am Lebensweg des Autors beschrieben, die seine Auseinandersetzung mit Gerechtigkeit geprägt haben. Der zweite Teil gibt Einblick in seine religionspädagogische Arbeit, in der die Frage nach Gerechtigkeit besonders bedeutsam war am Beispiel ‚Religion im Kontext Migration‘ und der ökumenischen Initiative ‚lebens.werte.schule‘. Die Vision vom Reich Gottes und die Notwendigkeit von Partizipation werden dabei deutlich.

  18. Die EG-Kabotageverordnung

    OpenAIRE

    Basedow, Jürgen

    1990-01-01

    Die EG-Kabotageverordnung : e. Schritt zur Verwirklichung d. Dienstleistungsfreiheit im Straßengüterverkehr / Jürgen Basedow ; Ansgar Held. - In: Europäische Zeitschrift für Wirtschaftsrecht. 1. 1990. S. 305-308

  19. Die Bibliothek des Bezirksmuseums Josefstadt

    Directory of Open Access Journals (Sweden)

    Maria Ettl

    2015-01-01

    Josefstadt in Wien werden die Herkunft der Bibliotheksbestände und die beengte Raumsituation beschrieben. Abschließend wird auf die Erfassung der Medien mittels der Bibliothekssoftware „Biblioweb“ eingegangen.

  20. Investigation of aluminium-rich alloy system of aluminium-strontium-silicium

    International Nuclear Information System (INIS)

    Ganiev, I.N.; Vakhobov, A.B.; Dzhuraev, T.D.; Alidzhanov, F.N.

    1976-01-01

    An area of the solid solution based on aluminium was studied, and the surface was plotted of the liquidus adjoining the apex of the aluminium corner of the strontium-aluminium-silicon system. The investigation was carried out by microstructure and differential thermal analyses and by the measurement of the microhardness of the component phases. A combined solubility of silicon and strontium in aluminium was studied along three radial sections at Sr-to-Si ratios of 1/2, 1/1 and 2/1. The relationships of ''composition vs. Microhardness'', obtained in these sections, made it possible to define the boundaries of the phase regions in the aluminium corner of the strontium-aluminium-silicon system at 500 deg C. The greatest solubility is that along the Al-SrAl 2 Si 2 section at a Sr/Si ratio of 1/2. A further increase in the content of strontium brings about a drop in the solubility of silicon in solid aluminium. The projection of the liquidus surface of the strontium-aluminium-silicon system, rich in aluminium, includes four surfaces of primary crystallization: α-Al, SrAl 4 , SrAl 2 Si 2 and Si. The system comprises a section of Al-SrAl 2 Si 2 representing a quasibinary system of an eutectic type. The eutectic reaction takes place at a temperature of 640 deg C. The quasibinary Al-SrAl 2 Si 2 section divides the aluminium corner of the Sr-Al-Si system into two independent systems Al-SrAl 4 -SrAl 2 Si 2 and Al-Si-SrAl 2 Si 2 of an eutectic type

  1. Die verband tussen die sielkundige kontrak en organisasieverbondenheid

    Directory of Open Access Journals (Sweden)

    K. J. Stanz

    1999-06-01

    Full Text Available The relationship between the psychological contract and organisational commitment. The aim of this study is to design a measuring instrument with acceptable metric characteristics for the strength of the psychological contract within the South African context, and to determine empirically the relation between the strength of the psychological contract and organisational commitment. The Dhammanungune Model served as foundation for the design of the Strength of the Psychological Contract Questionnaire which consists of two scales namely, a needs expectation scale and a needs fulfilment expectation scale. The items of each scale have been formulated in the manner that ensures that the respondent reacts consecutively to two instructions namely, (a the level of the expectation and (b the importance of the expectation. This questionnaire was administered together with the Organisational Commitment Questionnaire to two population groups within the military environment. The Pearson Product Moment Correlation was calculated between the strength of the psychological contract and organisational commitment and the significance of the correlations was evaluated. Opsomming Die doel van die studie is om 'n meetinstrument met aanvaarbare metriese eienskappe vir die sterkte van die sielkundige kontrak vir Suid-Afrikaanse omstandighede te ontwerp en om empirics die verband tussen die sterkte van die sielkundige kontrak en organisasieverbondenheid te bepaal. Die sterkte van die sielkundige kontrak vraelys is op grond van die Dhammanungune-model ontwerp en het uit twee skale naamlik, die behoefteverwagting- en vervullingsverwagtingskale bestaan. Items vir eike skaal is sodanig geformuleer dat die respondent agteropeenvolgens op twee instruksies naamlik (a die vlak van die verwagting en (b die belangrikheid van die verwagting moet reageer. Die vraelys is saam met die organisasieverbondenheidsvraelys op twee populasies uit 'n militere omgewing toegepas. Die Pearson

  2. Die postpolitische Stadt

    Directory of Open Access Journals (Sweden)

    Erik Swyngedouw

    2013-12-01

    Full Text Available Die Polis ist tot, es lebe die kreative Stadt! Während die Stadt, zumindest in Teilen des städtischen Raums, blüht und gedeiht, scheint die Polis im idealisierten griechischen Sinn dem Untergang geweiht; in diesem Verständnis ist sie der Ort der öffentlichen politischen Auseinandersetzung und demokratischen Unterhandlung und somit eine Stätte (oft radikaler Abweichung und Unstimmigkeit, an der die politische Subjektivierung buchstäblich ihren Platz hat. Diese Figur einer entpolitisierten (oder postpolitischen und postdemokratischen Stadt im Spätkapitalismus bildet das Leitmotiv des vorliegenden Beitrags. Ich lehne mich dabei an Jacques Rancière, Slavoj Žižek, Chantal Mouffe, Mustafa Dikeç, Alain Badiou und andere Kritiker jenes zynischen Radikalismus an, der dafür gesorgt hat, dass eine kritische Theorie und eine radikale politische Praxis ohnmächtig und unfruchtbar vor jenen entpolitisierenden Gesten stehen, die in der polizeilichen Ordnung des zeitgenössischen neoliberalen Spätkapitalismus als Stadtentwicklungspolitik [urban policy] und städtische Politik [urban politics] gelten. Ziel meiner Intervention ist es, das Politische wieder in den Mittelpunkt der zeitgenössischen Debatten über das Urbane zu stellen. [...

  3. Feasibility investigations on a novel micro-manufacturing process for fabrication of fuel cell bipolar plates: Internal pressure-assisted embossing of micro-channels with in-die mechanical bonding

    Energy Technology Data Exchange (ETDEWEB)

    Koc, Muammer [NSF I/UCR Center for Precision Forming (CPF), Department of Mechanical Engineering, Virginia Commonwealth University (VCU), Richmond, VA (United States); Mahabunphachai, Sasawat [NSF I/UCR Center for Precision Forming (CPF), Department of Mechanical Engineering, Virginia Commonwealth University (VCU), Richmond, VA (United States); Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI (United States)

    2007-10-25

    In this paper, we present the results of our studies on conceptual design and feasibility experiments towards development of a novel hybrid manufacturing process to fabricate fuel cell bipolar plates that consists of multi-array micro-channels on a large surface area. The premises of this hybrid micro-manufacturing process stem from the use of an internal pressure-assisted embossing process (cold or warm) combined with mechanical bonding of double bipolar plates in a single-die and single-step operation. Such combined use of hydraulic and mechanical forming forces and in-process bonding will (a) enable integrated forming of micro-channels on both surfaces (as anode and cathode flow fields) and at the middle (as cooling channels), (b) reduce the process steps, (c) reduce variation in dimensional tolerances and surface finish, (d) increase the product quality, (e) increase the performance of fuel cell by optimizing flow-field designs and ensuring consistent contact resistance, and (f) reduce the overall stack cost. This paper explains two experimental investigations that were performed to characterize and evaluate the feasibility of the conceptualized manufacturing process. The first investigation involved hydroforming of micro-channels using thin sheet metals of SS304 with a thickness of 51 {mu}m. The width of the channels ranged from 0.46 to 1.33 mm and the height range was between 0.15 and 0.98 mm. Our feasibility experiments resulted in that different aspect ratios of micro-channels could be fabricated using internal pressure in a controllable manner although there is a limit to very sharp channel shapes (i.e., high aspect ratios with narrow channels). The second investigation was on the feasibility of mechanical bonding of thin sheet metal blanks. The effects of different process and material variables on the bond quality were studied. Successful bonding of various metal blanks (Ni201, Al3003, and SS304) was obtained. The experimental results from both

  4. Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus

    Directory of Open Access Journals (Sweden)

    M. M. Nel

    1990-07-01

    Full Text Available Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus word beskryf. ’n Dun bindweefselkapsel omring die lewer. Die hepatosietrangskikking vertoon as lobules, met die koorde van hepatosiete wat vanaf ’n sentrale vene uitradieer en met mekaar anastomaseer. Indiwiduele lewerlohules vertoon nie duidelike grense nie, maar enkele duidelike triades word wel in die lewer van O. mossambicus aangetref. Die hepatosiete bevat ’n enkele ronde kern met ’n duidelike nukleolus en die growwe endoplasmiese retikula kom in twee of meer rye om die kerne en teen die selgrense van die hepatosiete voor. Die ander sitoplasmiese organelle kom verspreid in die hepatosietsitoplasma voor. Die eksokriene pankreasselle is om die portale venes gesetel. Die kerne van hierdie selle is rond en is hasaal in die kubies- tot silindervormige selle gelee. ’n Goedontwikkelde growwe endoplasmiese retikulum — vesikulêr, tubulêr en sirkulêr in vorm — en sektretoriese granules wat apikaal in die sel gelee is, kom voor.

  5. Potentiometric titration curves of aluminium salt solutions and its ...

    African Journals Online (AJOL)

    Potentiometric titration curves of aluminium salt solutions and its species conversion ... of aluminium salt solutions under the moderate slow rate of base injection. ... silicate radical, and organic acid radical on the titration curves and its critical ...

  6. Effect of tempering on corrosion resistance of cast aluminium bronzes

    International Nuclear Information System (INIS)

    Aaltonen, P.; Klemetti, K.; Haenninen, H.

    1985-01-01

    The subject of this study is corrosion resistance of aluminium bronzes, which are copper base alloys containing aluminium up to 12% with additions of nickel, iron and manganese. The main conclutions that can be drawn are: (1) The dealloying corrosion resistance of nickel-aluminium bronze is much better than that of aluminium bronze with iron and manganese additions, but it is not immune; (2) The dealloying corrosion resistance of aluminium bronzes can be improved by appropiate heat treatments. The best properties were obtained by temperering between 600 and 800 deg C, depending on the initial microstructure; (3) In crevice conditions, where local acidification can occur, dealloying of aluminium bronzes is a consequence of the preferential attack of aluminium-rich phases. By appropriate tempering, a uniform distribution of aluminium-rich phases is obtained and the continous path for selective corrosion is not formed

  7. Aluminium hydroxide-the carrier for catalysts coating

    International Nuclear Information System (INIS)

    Normatov, I.Sh.; Mirsaidov, U.M.

    2003-01-01

    At present time several methods of receiving aluminium hydroxide are exist. But all they differ by much staging of process connected with preliminary receiving of intermediate compounds, with application of expensive metallic aluminium

  8. Die teologiese arbeid van Antonius HJ Gunneweg

    African Journals Online (AJOL)

    En dis 'n klein treetjie van klagte na aanklag en na protes teen die gode, die heersers wat die mens vernietig deur hom oor sy ware lewe te bedrieg. Die ideologie eis dan ook dienooreenkomstig die bevryding en emansipasie van die mens van die gode en van God (1983: 118—119). Volgens die Jahwis is dit die slang wat, ...

  9. Die benutting van vraelyste met die oog op meer effektiewe ...

    African Journals Online (AJOL)

    UPuser

    effektiewe stresbeheer as een van die temas te hanteer. Op grond van die navorsing deur onder andere Lawson (1985) en Taylor (1999) sou ek graag die proses van differensiasie2 ook by genoemde lys voeg as tema vir bespreking tydens huweliksvoorbereiding. 2 Differensiasie kan beskryf word as die losmaakproses ...

  10. die aard van wetgewende diskresies by die suid-afrikaanse ...

    African Journals Online (AJOL)

    Administrator

    In enige moderne demokrasie is daar een of ander vorm van skeiding van magte tussen die wetgewende, uitvoerende en regsprekende gesag. Hierdie skeiding van magte, die sogenaamde trias politica, kan sover teruggevoer word as 1215, met die ondertekening van die Magna Carta deur Koning John van Engeland.

  11. die doeltreffendheid van die afrikaanse woordelys en spelreels

    African Journals Online (AJOL)

    sluiting by die reel vir die verdubbeling van medeklinkers na 'n kort, be- klemtoonde klinker, woorde soos ballet, ballon, terras, terrein, dissipel en dissipline slegs met een konsonant na die eerste vokaal gespel moes word, omdat daardie voorafgaande vokaal onbeklemtoon is. Ook hierdie uit- sondering op die reel word ...

  12. Die aanspraak op Goddelike steun in 'n konfliksituasie volgens die ...

    African Journals Online (AJOL)

    laws, and ethical or political principles. A synchronic investigation of relevant Old ... die toneel gebring met die vraag: 'aan wie se kant is God' (vgl bv The road to. Damascus 1979:6)? Volgens .... betrekking tot die Ou Testament: Hoe moet ons vasstel wie se kant God nou regtig kies, of wie veg aan die kant van God en wie ...

  13. Effect of Sintering Temperature on the Properties of Aluminium-Aluminium Oxide Composite Materials

    Directory of Open Access Journals (Sweden)

    Dewan Muhammad Nuruzzaman

    2016-12-01

    Full Text Available In this study, aluminium-aluminium oxide (Al-Al2O3 metal matrix composites of different weight percentage reinforcements of aluminium oxide were processed at different sintering temperatures. In order to prepare these composite specimens, conventional powder metallurgy (PM method was used. Three types specimens of different compositions such as 95%Al+5%Al2O3, 90%Al+10%Al2O3 and 85%Al+15%Al2O3 were prepared under 20 Ton compaction load. Then, all the specimens were sintered in a furnace at two different temperatures 550oC and 580oC. In each sintering process, two different heating cycles were used. After the sintering process, it was observed that undistorted flat specimens were successfully prepared for all the compositions. The effects of sintering temperature and weight fraction of aluminium oxide particulates on the density, hardness and microstructure of Al-Al2O3 composites were observed. It was found that density and hardness of the composite specimens were significantly influenced by sintering temperature and percentage aluminium oxide reinforcement. Furthermore, optical microscopy revealed that almost uniform distribution of aluminium oxide reinforcement within the aluminium matrix was achieved.

  14. Aluminium and the human breast.

    Science.gov (United States)

    Darbre, P D

    2016-06-01

    The human population is exposed to aluminium (Al) from diet, antacids and vaccine adjuvants, but frequent application of Al-based salts to the underarm as antiperspirant adds a high additional exposure directly to the local area of the human breast. Coincidentally the upper outer quadrant of the breast is where there is also a disproportionately high incidence of breast cysts and breast cancer. Al has been measured in human breast tissues/fluids at higher levels than in blood, and experimental evidence suggests that at physiologically relevant concentrations, Al can adversely impact on human breast epithelial cell biology. Gross cystic breast disease is the most common benign disorder of the breast and evidence is presented that Al may be a causative factor in formation of breast cysts. Evidence is also reviewed that Al can enable the development of multiple hallmarks associated with cancer in breast cells, in particular that it can cause genomic instability and inappropriate proliferation in human breast epithelial cells, and can increase migration and invasion of human breast cancer cells. In addition, Al is a metalloestrogen and oestrogen is a risk factor for breast cancer known to influence multiple hallmarks. The microenvironment is established as another determinant of breast cancer development and Al has been shown to cause adverse alterations to the breast microenvironment. If current usage patterns of Al-based antiperspirant salts contribute to causation of breast cysts and breast cancer, then reduction in exposure would offer a strategy for prevention, and regulatory review is now justified. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  15. Advances in development and application of aluminium batteries

    DEFF Research Database (Denmark)

    Qingfeng, Li; Zhuxian, Qiu

    2001-01-01

    Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation o...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

  16. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P

    2005-01-01

    The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

  17. Analysis of aluminium in rat following administration of allergen immunotherapy using either aluminium or microcrystalline-tyrosine-based adjuvants.

    Science.gov (United States)

    McDougall, Stuart A; Heath, Matthew D; Kramer, Matthias F; Skinner, Murray A

    2016-03-01

    Investigation into the absorption, distribution and elimination of aluminium in rat after subcutaneous aluminium adjuvant formulation administration using ICP-MS is described. Assays were verified under the principles of a tiered approach. There was no evidence of systemic exposure of aluminium, in brain or in kidney. Extensive and persistent retention of aluminium at the dose site was observed for at least 180 days after administration. This is the first published work that has quantified aluminium adjuvant retention based on the quantity of aluminium delivered in a typical allergy immunotherapy course. The results indicate that the repeated administration of aluminium-containing adjuvants will likely contribute directly and significantly to an individual's body burden of aluminium.

  18. Aluminium toxicity tolerance in crop plants: Present status of research

    African Journals Online (AJOL)

    ... tolerance of which genes of the Aluminium-activated malate transporter (ALMT) and multidrug and toxic compound extrusion (MATE) families are prominent. In this review, the progress of research in identifying aluminium toxicity tolerant genes is discussed. Keywords: Aluminium toxicity, soil acidity, hydroponic screening, ...

  19. Aluminium allergy and granulomas induced by vaccinations for children

    DEFF Research Database (Denmark)

    Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

    2014-01-01

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

  20. Aluminium allergy and granulomas induced by vaccinations for children

    DEFF Research Database (Denmark)

    Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

    2014-01-01

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...

  1. Spectrophotometric determination of aluminium in steel with xylenol orange

    International Nuclear Information System (INIS)

    Majeed, A.; Javed, N.; Khan, M.S.

    1996-01-01

    Spectrophotometric determination of Aluminium in steel based on colour reaction between Aluminium and xylenol orange has been carried out. Red coloured complex formed in weak acidic solution is measured for its absorbance at 550 nm. The various optimum experimental conditions for Aluminium xylenol orange (Al-Xo) complex have been studied. (author)

  2. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  3. Corrosion behaviour of borated aluminium used as neutron absorber

    Energy Technology Data Exchange (ETDEWEB)

    Emmerich, R. [EaglePicher Technologies GmbH, Oehringen (Germany); Ensinger, W.; Enders, B. [Philipps-Univ. of Marburg, Dept. of Chemistry, Material Science Centre (Germany)

    2004-07-01

    The electrochemical behaviour of pure and borated aluminium was examined. Measurements were performed in two different electrolytes at 90 C containing different trace-amounts of chloride. For borated aluminium current transients, i.e. metastable depassivation events were found. It is suggested to attribute these transients to less stable passivation layers in comparison to pure aluminium.

  4. Internal friction in iron-aluminium alloys having a high aluminium content

    International Nuclear Information System (INIS)

    Hillairet, J.; Delaplace, J.; Silvent, A.

    1966-01-01

    By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author) [fr

  5. Process for the manufacture of plates containing neutron poison from aluminium and aluminium alloys

    International Nuclear Information System (INIS)

    Bauer, G.; Pollmann, E.; Srostlik, P.

    1985-01-01

    A process for guaranteeing sub-critical arrangements of nuclear fuel in tranport and/or storage containers is described, in which a homogeneous distribution of neutron poison in the aluminium matrix is guaranteed. A homogeneous mixture of aluminium powder and neutron poison powder is produced, this is pressed into plates in several stages, dried and made into hollow aluminium profiles of rectangular cross-section. The open ends of the hollow profile are then closed and this is rolled to the required dimension at 470-500 0 C. (orig./HP) [de

  6. TITANIUM CARBON ALUMINIUM : A NOVEL GRAIN REFINER FOR ALUMINIUM-LITHIUM ALLOYS

    OpenAIRE

    Birch , M.; Cowell , A.

    1987-01-01

    This work explores the possibility of achieving grain size control in aluminium-lithium alloys with the titanium carbon aluminium (TiCAl) master alloys invented at the Technical University of Berlin and developed by London and Scandinavian Metallurgical Co Ltd (LSM). Grain refining tests were conducted on a single batch of 8090 alloy using addition rates of 0.2wt% and 0.4wt% of TiCAl and 3/1 titanium boron aluminium (TiBAl). Other tests using 0.4wt% of binary TiAl gave poor results, showing t...

  7. Die huwelik as identiteitsmerker in die Ou Testament

    African Journals Online (AJOL)

    p1243322

    Gen 2:18). Uit die woorde van Genesis 2:24 dat man en vrou een sal wees, lei die derde formulier af dat dit “getuig dat die huwelik 'n allesinsluitende gemeenskap is ..... die formule gebruik word: “Hier volg die vertelling oor X se nageslag.” (Gen ..... verwys daarna as “intertwining the principal value concepts of tradition”.

  8. Molybdenum solubility in aluminium nitrate solutions

    Energy Technology Data Exchange (ETDEWEB)

    Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

    2016-07-01

    For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

  9. Anodization of cast aluminium alloys produced by different casting methods

    Directory of Open Access Journals (Sweden)

    K. Labisz

    2008-08-01

    Full Text Available In this paper the usability of two casting methods, of sand and high pressure cast for the anodization of AlSi12 and AlSi9Cu3 aluminium cast alloys was investigated. With defined anodization parameters like electrolyte composition and temperature, current type and value a anodic alumina surface layer was produced. The quality, size and properties of the anodic layer was investigated after the anodization of the chosen aluminium cast alloys. The Alumina layer was observed used light microscope, also the mechanical properties were measured as well the abrasive wear test was made with using ABR-8251 equipment. The researches included analyze of the influence of chemical composition, geometry and roughness of anodic layer obtained on aluminum casts. Conducted investigations shows the areas of later researches, especially in the direction of the possible, next optimization anodization process of aluminum casting alloys, for example in the range of raising resistance on corrosion to achieve a suitable anodic surface layer on elements for increasing applications in the aggressive environment for example as materials on working building constructions, elements in electronics and construction parts in air and automotive industry.

  10. Consolidation of copper and aluminium powders by spark plasma sintering

    Science.gov (United States)

    Saiprasad, M.; Atchayakumar, R.; Thiruppathi, K.; Raghuraman, S.

    2016-09-01

    Processing in the powder metallurgy route has emerged as an economical process for the production of near net shaped components with a wide range of desired mechanical properties suitable for various applications of industrial needs. This research work was conducted with an objective of studying the improvisation of density and hardness of Copper-Aluminium alloy prepared by spark plasma sintering. Cu-Al alloy with a composition of 95% copper and 5% aluminium was prepared by SPS process. SPS is a low voltage, DC pulse current activated, pressure-assisted sintering, which enables sintering at lower temperatures and shorter durations. The combination offered by Cu-Al alloy of high strength and high corrosion resistance results their applications under a wide variety of conditions. The density and hardness of the prepared sample were measured by conducting appropriate tests. Apparently, the values of hardness and density of the specimen prepared by SPS seemed to be better than that of conventional sintering. The experimental procedure, testing methodologies and analysis are presented.

  11. Pressure Effect on Entrance Flow

    DEFF Research Database (Denmark)

    Christensen, Jens Horslund; Couch, Mark

    1997-01-01

    The paper reports on experimentally determined pressure drops associated with orifice and capillary dies, where the exit pressure is elevated. The effect of hydrostatic pressure up to 70 MPa is reported for PS, LDPE and PP melts.......The paper reports on experimentally determined pressure drops associated with orifice and capillary dies, where the exit pressure is elevated. The effect of hydrostatic pressure up to 70 MPa is reported for PS, LDPE and PP melts....

  12. Defect generation during solidification of aluminium foams

    International Nuclear Information System (INIS)

    Mukherjee, M.; Garcia-Moreno, F.; Banhart, J.

    2010-01-01

    The reason for the frequent occurrence of cell wall defects in metal foams was investigated. Aluminium foams often expand during solidification, a process which is referred as solidification expansion (SE). The effect of SE on the structure of aluminium foams was studied in situ by X-ray radioscopy and ex situ by X-ray tomography. A direct correlation between the magnitude of SE and the number of cell wall ruptures during SE and finally the number of defects in the solidified foams was found.

  13. An aluminium evaporation source for ion plating

    International Nuclear Information System (INIS)

    Walley, P.A.; Cross, K.B.

    1977-01-01

    Ion plating with aluminium is becoming increasingly accepted as a method of anti-corrosion surface passivation, the usual requirements being for a layer between 12 and 50 microns in thickness, (0.0005 to 0.002). The evaporation system described here offers a number of advantages over high power electron beam sources when used for aluminium ion plating. The source consists of a resistively heated, specially shaped, boron nitride-titanium diboride boat and a metering feed system. Its main features are small physical size, soft vacuum compatibility, low power consumption and metered evaporation output. (author)

  14. Narratiwiteit en die Ou Testament

    African Journals Online (AJOL)

    INLEIDING. Die literêre benadering tot die Ou-Testamentiese narratiewe word algemeen as 'n alternatiewe paradigma in die Bybelwetenskappe aanvaar. Oor die filosofiese uit- gangspunte wat hierdie nuwe paradigma ten grondslag lê, bestaan daar egter nog weinig eenstemmigheid. Heelwat probleme van filosofiese en ...

  15. Eksistensialisme in die Franse letterkunde

    Directory of Open Access Journals (Sweden)

    A. A. Teurlinckx

    1966-03-01

    Full Text Available Nooit sou die Franse jeug — en die van Europa en verder — in dié mate deur die eksistensialisme be'invloed gewees het nie, indien hierdie filosofie in wysgerige traktate sou begrawe gelê het. Die eksistensialiste het die koning van die filosofiese verhaal, Voltaire, met sukses op sy Candide- en Zadig-pad gevolg en hulle teorieë in letterkundige werke, ver- hale, romans en ook toneelstukke kwytgeraak, wat baie gelees is en waaruit ook ander literatore kragte en inspirasie geput het. Omrede daarvan is daar inderdaad baie eksistensialisme in die Franse letterkunde, maar ’n eintlike eksistensialistiese letterkunde was daar nie, en ’n Eksistensialistiese Letterkun­ dige skool het nooit bestaan nie. Ook sit hierdie eksistensialiste nie langs dieselfde vuur nie. Die Christelike eksistensialis Gabriel Marcel het op 21 April van hierdie jaar uitgevaar teen die „Sartriane” na aanleiding van die opvoering van Les Paravents, Die W indskerms van Jean Genêt in ’n Paryse staatsondersteunde teater. „Mens mag seker wees”, skryf Marcel in Les Nouvelles Littéraires, „dat die hele sartriaanse parogie sal skreeu: groot meesterwerk”. Voortgaande op sy distansiëring kan die literêre eksistensialiste in drie groepe ingedeel word: 1. Die Sartriane; 2. Die Christelike Eksistensialiste; 3. Die Onafhanklikes.

  16. The determination of trace oxygen in aluminium and aluminium-silicon alloy by helium-3 activation analysis

    International Nuclear Information System (INIS)

    Vandecasteele, C.; Goethals, P.; Kieffer, R.; Hoste, J.

    1975-01-01

    The determination of oxygen in aluminium and aluminium-silicon alloy by helium-3 activation is studied. The 18 F formed from oxygen is separated by distillation followed by precipitation of leadfluorochloride. The chemical yield is determined by activation in an isotopic neutron source. Concentrations of resp. 27 and 64 ng.g -1 with a precision for a single determination of resp. 30 and 13% are found in 99.5% aluminium and in aluminium-silicon (3%) alloy. (author)

  17. Assisted Dying in Canada.

    Science.gov (United States)

    Schuklenk, Udo

    This paper makes an affirmative ethical case in favour of the decriminalization of assisted dying in Canada. It then proceeds to defending the affirmative case against various slippery-slope arguments that are typically deployed by opponents of assisted dying. Finally, a recent case of questionable professional conduct by anti-euthanasia campaigners cum academics is flagged as a warning to all of us not to permit the quality of the professional debate to deteriorate unacceptably, despite the personal emotional investments involved on all sides of the debate.

  18. Durability of bare and anodised aluminium in atmosphere of very different corrosivities I. Bare aluminium

    International Nuclear Information System (INIS)

    Gonzalez, J. A.; Escudero, E.; Lopez, V.; Simancas, J.; Morcillo, M.

    2004-01-01

    The behaviour of bare aluminium is studied in atmospheric exposure at 11 natural testing stations with salinity levels ranging between 2.1 and 684 mg Cl''- m''-2 d''-1. In atmospheres of low or moderate aggressivity aluminium behaves as a passive material, though the insignificant corrosion that is produced is sufficient to spoil its appearance. In contrast, at salinity levels of 50 mg Cl''- m''-2 ''-1 or above, aluminium is susceptible to pitting corrosion even in the first year of atmospheric exposure, or in the second year at salinities of ≤ 10 mg Cl''- m''-2 d''-1. For comparative purposes, results are included for aluminium protected with an anodic film of 28 μm thickness exposed at the same testing stations. A 28 μm anodic film, correctly sealed, prevents the risk of localised corrosion even in the most unfavourable situations. (Author) 23 refs

  19. Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.

    1968-01-01

    Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produces...... rows of dislocation loops all lying parallel to one particular direction. If the aluminium target is quenched from 600 °C and annealed at room temperature prior to irradiation with aluminium ions, the rows of loops are suppressed. The amount of damage observed is considerably less than would...

  20. Die afrikaner en sy pers*

    Directory of Open Access Journals (Sweden)

    G. D. Scholtz

    1963-03-01

    Full Text Available Die versoek w at van u inrigting tot my gekom het om buitengewone professor in die Persw etenskap te word, was vir my deels vererend, m aar deels het dit my in 'n moeilike posisie gestel. Dit was vir my vererend, om dat dit gekom het van 'n universiteit m et wie se Christelik- Nasionale koers ek my ten voile kan vereenselwig. Dit was dan ook vir my vererend, om dat ek daardeur in staat gestel kan w ord om die volk w aartoe ek behoort, op 'n vir my nuwe terrein te dien. As sodanig is dit vir my im m ers m oontlik om ook ’n beskeie bydrae te lewer tot die geestelike vorm ing van die jeug van ons volk. Dit het my m oeilik geval om, w aar ek reeds die m iddeljarige leeftyd bereik het, nou vir die eerste maal as dosent op te tree, aangesien ek daarvan in die verlede nie die m inste kennis en ervaring opgedoen het nie. As joernalis rig ek my im m ers tot die breë publiek deur middel van die pen. As dosent m oet ek my deur middel van die mond tot die studente rig. Dit lê voor die hand dat die eise w at so aan my gestel word, totaal anders is as dié waar- aan ek oor 'n tydperk van m eer as 'n kw arteeu as joer­ nalis gewoond geraak het.

  1. Die vestiging van die Kerk in Natal, die Vrystaat en Transvaal na ...

    African Journals Online (AJOL)

    as eerste predikant van die Voortrekkers laat orden en bevestig. Daama het verskeie kerksake van tyd tot tyd aandag geniet. Met betrekking tot die bevestiging van huwelike stel Retief 'n meer ordelike reëling daar, naamlik dat die gebooie van voomemende egpa- re van nou af drie maal in die kerk afgekondig moes wrord ...

  2. Die skool en die onderwyser as faktore in die geestesgesondheid van die kind*

    Directory of Open Access Journals (Sweden)

    B. C. Schutte

    1961-03-01

    Full Text Available Ons hou geestesgesondheidsweke, stig beroepsentrums, samel geld in om mense wat geestelik siek is te genees, klae oor die tekort aan psigiaters, kliniese sielkundiges, bedryfsielkundiges, voorligters, skoolpsigoloë,ens. ’n Karige kwarteeu gelede het ons aan al hierdie dinge slegs akademiese aandag gewy. In hierdie kursus wordverskeie tipes kinders bespreek en geleer hoe om hulle probleme te benader.

  3. When Somebody Dies

    Science.gov (United States)

    ... bottle became useless. The container is gone, but what's inside — the water — remains. The part of a person that's left after the body dies is often called the "soul" or "spirit." Some people believe the soul is the part ...

  4. Die Kunst des Scheiterns

    DEFF Research Database (Denmark)

    Juul, Jesper

    2014-01-01

    Menschen haben von Kindesbeinen an das Verlangen, Erfolge zu erzielen und Kompetenz zu erreichen. Computerspieler entscheiden sich jedoch fortlaufend für eine Aktivität, die oft und wiederholt zum Verlieren führen muss und ein taubes Gefühl der Unfähigkeit erzeugt. Im Kino, im Theatersaal und bei...

  5. Aluminium Phosphide Poisoning: Two Pediatric Patients and Two Different Clinical Outcomes

    Directory of Open Access Journals (Sweden)

    Faruk Ekinci

    2017-08-01

    Full Text Available Aluminium phosphide is an insecticide that turns into a quite toxic gas called phosphine when contacts with gastric fluids. Aluminium phosphide poisoning causes severe metabolic acidosis, acute respiratory distress syndrome and multi-organ failure with cardiogenic shock. Our first case was an-18-year-old girl admitted to our emergency department two hours after ingestion of one tablet containing 500 mg aluminium phosphide in a suicide attempt. Venoarterial extracorporeal membrane oxygenation was started one hour after initiation of inotropic agents. Despite improvement in hemodynamic status, she developed refractory arrhythmias at the12th hour and she died 22 hours after admission. The second case was a two-year-old girl who was admitted to our emergency department because of observing a piece of aluminum phosphide 500 mg tablet broken in her mouth. Her vital signs were stable in the follow-up. The patient who had no problems in the follow-up was discharged at 48 hours.

  6. Diffusion bonding of transition structures for integral aluminium-fibre reinforced polymer (FRP) compounds

    Energy Technology Data Exchange (ETDEWEB)

    Hehl, A. von [IWT - Stiftung Institut fuer Werkstofftechnik, Hauptabteilung Werkstofftechnik, Bremen (Germany); Syassen, F. [Airbus Operations GmbH, Metal Technology, Bremen (Germany); Schimanski, K.

    2012-04-15

    Components in hybrid design become more and more important in terms of their lightweight potential. In this context the demand for weight saving in aerospace leads to increasing numbers of applications of fibre composites for primary structural components. In consequence the use of FRP-metal compounds is necessary. Within the investigations of the researcher group ''Schwarz Silber'' (FOR 1224) founded by the DFG (German Research Foundation) material optimised interface structures for advanced CFRP-aluminium compounds are currently being studied. Within their work the researcher group focussed on three concepts realizing the transition structures: the usage of wires (titanium), foils (titanium) and fibres (glass fibre) as transition elements between CFRP and aluminium. For the connection of the aluminium sheet and the transition element die-casting and laser beam welding are basically used. As a possible alternative to the both liquid phase processes a feasibility study haven been done focussing the solid state processes diffusion bonding. The experimental results show the high potential of this process in view of the transferable loads for integral transition structures. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Fabrication of porous aluminium with directional pores through thermal decomposition method

    International Nuclear Information System (INIS)

    Nakajima, H; Kim, S Y; Park, J S

    2009-01-01

    Lotus-type porous metals were fabricated by unidirectional solidification in pressurized gas atmosphere. The elongated pres are evolved by insoluble gas resulted from the solubility gap between liquid and solid when the melt is solidified. Recently we developed a novel fabrication technique, in which gas compounds are used as a source of dissolving gas instead of the high pressure. In the present work this gas compound method was applied to fabrication of lotus aluminium. Hydrogen decomposed from calcium hydroxide, sodium bicarbonate and titanium hydride evolves cylindrical pores in aluminium. The porosity is about 20%. The pore size decreases and the pore number density increases with increasing amount of calcium hydroxide, which is explained by increase in pore nucleation sites.

  8. Modelle in die onderrig van fisika

    Directory of Open Access Journals (Sweden)

    J. J. A. Smit

    1998-07-01

    Full Text Available Die rol van modelle in die onderrig van fisika is sedert die vroeë tagtigerjare erken. In die onderrig word die absent op die kwantitaiewe aspekte van die vak geplaas, terwyl die kwatitatiewe aspekte min aandag kry.

  9. DIE SAGD - SY ONTSTAAN EN ONTWIKKELING

    African Journals Online (AJOL)

    31 Okt 1977 ... stelling van 'n higiene afdeling het in 'n belang- rike behoefte voorsien. Die pligte van die SAGO het dus op hierdie stadium die ondersoek van soldate, die sanita- sie van kampe, die verpleging van pasiente in militere hospitale en die opleiding van lede be- hels. 'n Hoogtepunt was die opening van die.

  10. Dimensional control of die castings

    Science.gov (United States)

    Karve, Aniruddha Ajit

    The demand for net shape die castings, which require little or no machining, is steadily increasing. Stringent customer requirements are forcing die casters to deliver high quality castings in increasingly short lead times. Dimensional conformance to customer specifications is an inherent part of die casting quality. The dimensional attributes of a die casting are essentially dependent upon many factors--the quality of the die and the degree of control over the process variables being the two major sources of dimensional error in die castings. This study focused on investigating the nature and the causes of dimensional error in die castings. The two major components of dimensional error i.e., dimensional variability and die allowance were studied. The major effort of this study was to qualitatively and quantitatively study the effects of casting geometry and process variables on die casting dimensional variability and die allowance. This was accomplished by detailed dimensional data collection at production die casting sites. Robust feature characterization schemes were developed to describe complex casting geometry in quantitative terms. Empirical modeling was utilized to quantify the effects of the casting variables on dimensional variability and die allowance for die casting features. A number of casting geometry and process variables were found to affect dimensional variability in die castings. The dimensional variability was evaluated by comparisons with current published dimensional tolerance standards. The casting geometry was found to play a significant role in influencing the die allowance of the features measured. The predictive models developed for dimensional variability and die allowance were evaluated to test their effectiveness. Finally, the relative impact of all the components of dimensional error in die castings was put into perspective, and general guidelines for effective dimensional control in the die casting plant were laid out. The results of

  11. Die transvaalse ontwerp-ordonnansie oor die onderwys

    Directory of Open Access Journals (Sweden)

    J. C. Coetzee

    1952-03-01

    Full Text Available In ’n Buitengewone Provinsiale Koerant van die Provinsie Transvaal is onder datum 25 Junie 1952 gepubliseer ’n „Ontwerp-Ordonnansie tot samevatting en wysiging van die Wette betreffende die Sentrale Beheer van die Onderwys, die Plaaslike Beheer van Skole, Godsdiensonderrig in Openbare Skole, Taal en die Onderwys, Onderwyspersoneel, Verpligte Onderwys, Toelating van Leerlinge tot Skole, Klasse of Inrigtings, Openbare Onderwys, Private Skole, Onderwys vir Kleurlinge en Asiate en Onderwys vir Naturelle, en om vir sake in verband daarmee voorsiening te maak” .

  12. DIE HEDENDAAGSE SIENING VAN DIE NORMERING VAN DUITS ...

    African Journals Online (AJOL)

    v a k t a a l k w a l i £ i k a s i e s ) neem d i e I n s t i t u t t a l l e take waar ter u i t b r e i d i n g van kennis van die Duitse taal in die buiteland. Sedert 1964 publiseer die. Institut die tydskrif Deutsch als Fremdsprache met die bylae Sprachpraxis, asook 'n handboek met die titel Deutsch - eln Lehrbuch Eur Auslander (Duits.

  13. Influence of Various Process Parameters on the Density of Sintered Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    Mateusz Laska

    2012-01-01

    Full Text Available This paper presents the results of density measurements carried out on Alumix sintered parts. ECKA Alumix aluminium powders were used because of their wide application in the powder metallurgy industry. The compacts were produced using a wide range of compaction pressures for three different chemical compositions. The compacts were then sintered under a pure dry nitrogen atmosphere at three different temperatures. The heating and cooling rates were the same throughout the entire test. The results showed that the green density increases with compaction pressure, but that sintered density is independent of green density (compaction pressure for each sintering temperature.

  14. Mechanical behaviour of aluminium-lithium alloys

    Indian Academy of Sciences (India)

    Aluminium-lithium alloys hold promise of providing a breakthrough response to the crying need for lightweight alloys for use as structurals in aerospace applications. Considerable worldwide research has gone into developing a range of these alloys over the last three decades. As a result, substantial understanding has ...

  15. Silicon Alloying On Aluminium Based Alloy Surface

    International Nuclear Information System (INIS)

    Suryanto

    2002-01-01

    Silicon alloying on surface of aluminium based alloy was carried out using electron beam. This is performed in order to enhance tribological properties of the alloy. Silicon is considered most important alloying element in aluminium alloy, particularly for tribological components. Prior to silicon alloying. aluminium substrate were painted with binder and silicon powder and dried in a furnace. Silicon alloying were carried out in a vacuum chamber. The Silicon alloyed materials were assessed using some techniques. The results show that silicon alloying formed a composite metal-non metal system in which silicon particles are dispersed in the alloyed layer. Silicon content in the alloyed layer is about 40% while in other place is only 10.5 %. The hardness of layer changes significantly. The wear properties of the alloying alloys increase. Silicon surface alloying also reduced the coefficient of friction for sliding against a hardened steel counter face, which could otherwise be higher because of the strong adhesion of aluminium to steel. The hardness of the silicon surface alloyed material dropped when it underwent a heating cycle similar to the ion coating process. Hence, silicon alloying is not a suitable choice for use as an intermediate layer for duplex treatment

  16. Warm Deep Drawing of Aluminium Sheet

    NARCIS (Netherlands)

    Bolt, P.J.; Werkhoven, R.J.; van den Boogaard, Antonius H.

    2003-01-01

    Aluminium sheet drawing processes can be improved by manipulating local flow behaviour by means of elevated temperatures and temperature gradients in the tooling. Forming tests showed that a substantial improvement is possible not only for 5xxx but also for 6xxx series alloys. Finite element method

  17. Complexes of alkylphenols with aluminium halides

    International Nuclear Information System (INIS)

    Golounin, A.V.

    1997-01-01

    Interaction of aluminium halides with alkylphenols is studied through the NMR method. The peculiarity of complex formation of pentamethylphenol with AlI 3 is revealed. By AlI 3 action on the pentamethylphenol the complexes are formed both of keto- and oxy form [ru

  18. Plasma metallization of aluminium oxide powder

    International Nuclear Information System (INIS)

    Smirnov, A.I.; Petrunichev, V.A.

    1981-01-01

    The sintering ability of cermets of metallized granulas of aluminium and matrix materials, such as chromium, nickel and nichrome is studied. Deformation tests of samples of cermets with molybdenum coated granules show satisfactory results at normal and high temperatures without fracture of metall-oxide interfaces [ru

  19. Molecular breeding of cereals for aluminium resistance

    Science.gov (United States)

    Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

  20. Constant structure creep experiments on aluminium

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel

    2011-01-01

    Roč. 49, č. 5 (2011), s. 307-318 ISSN 0023-432X R&D Projects: GA AV ČR IAA2041203 Institutional research plan: CEZ:AV0Z20410507 Keywords : mechanical properties * high temperature deformation * creep * aluminium Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.451, year: 2011

  1. Creep properties of aluminium processed by ECAP

    Czech Academy of Sciences Publication Activity Database

    Král, Petr; Dvořák, Jiří; Jäger, Aleš; Kvapilová, Marie; Horita, Z.; Sklenička, Václav

    2016-01-01

    Roč. 54, č. 6 (2016), s. 441-451 ISSN 0023-432X R&D Projects: GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 ; RVO:68378271 Keywords : equal channel angular pressing (ECAP) * aluminium * ultrafine-grained microstructure * creep Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) Impact factor: 0.366, year: 2016

  2. Optimum stamping die structure based on analytical method of die deformation during draw process; Seikei katei no kanagata henkei kaiseki ni motozuku, press kanagata kozo no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, T; Tamai, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We measured an actual deformation and pressure distribution in draw process of bending cam, and analyzed deformation process of die structure, in order to eliminate adjusting work considering die deformation by stamping force. We studied die structure improvement with simulation based on analytical method. This report describes a sample of die structure improvement based on a simulation and actual measurement. 1 ref., 11 figs., 1 tab.

  3. Navigating "Assisted Dying".

    Science.gov (United States)

    Schipper, Harvey

    2016-02-01

    Carter is a bellwether decision, an adjudication on a narrow point of law whose implications are vast across society, and whose impact may not be realized for years. Coupled with Quebec's Act Respecting End-of-life Care it has sharply changed the legal landscape with respect to actively ending a person's life. "Medically assisted dying" will be permitted under circumstances, and through processes, which have yet to be operationally defined. This decision carries with it moral assumptions, which mean that it will be difficult to reach a unifying consensus. For some, the decision and Act reflect a modern acknowledgement of individual autonomy. For others, allowing such acts is morally unspeakable. Having opened the Pandora's Box, the question becomes one of navigating a tolerable societal path. I believe it is possible to achieve a workable solution based on the core principle that "medically assisted dying" should be a very rarely employed last option, subject to transparent ongoing review, specifically as to why it was deemed necessary. My analysis is based on 1. The societal conditions in which have fostered demand for "assisted dying", 2. Actions in other jurisdictions, 3. Carter and Quebec Bill 52, 4. Political considerations, 5. Current medical practice. Leading to a series of recommendations regarding. 1. Legislation and regulation, 2. The role of professional regulatory agencies, 3. Medical professions education and practice, 4. Public education, 5. Health care delivery and palliative care. Given the burden of public opinion, and the legal steps already taken, a process for assisted-dying is required. However, those legal and regulatory steps should only be considered a necessary and defensive first step in a two stage process. The larger goal, the second step, is to drive the improvement of care, and thus minimize assisted-dying.

  4. Analysis of the Causes of Cracks in a Thick-Walled Bush Made of Die-Cast Aluminum Bronze

    Directory of Open Access Journals (Sweden)

    Pisarek B.P.

    2016-12-01

    Full Text Available For the die casting conditions of aluminium bronzes assumed based on the literature data, a thick-walled bush was cast, made of complex aluminium bronze (Cu-Al-Fe-Ni-Cr. After the cast was removed from the mould, cracks were observed inside it. In order to identify the stage in the technological production process at which, potentially, the formation of stresses damaging the continuity of the microstructure created in the cast was possible (hot cracking and/or cold cracking, a computer simulation was performed. The article presents the results of the computer simulation of the process of casting the material into the gravity die as well as solidifying and cooling of the cast in the shape of a thick-walled bush. The simulation was performed with the use of the MAGMA5 program and by application of the CuAl10Ni5,5Fe4,5 alloy from the MAGMA5 program database. The results were compared with the location of the defects identified in the actual cast. As a result of the simulation of the die-casting process of this bush, potential regions were identified where significant principal stresses accumulate, which can cause local hot and cold cracking. Until now, no research has been made of die-cast aluminium bronzes with a Cr addition. Correlating the results of the computer simulation validated by the analysis of the actual cast made it possible to clearly determine the critical regions in the cast exposed to cracking and point to the causes of its occurrence. Proposals of changes in the bush die casting process were elaborated, in order to avoid hot tearing and cold cracking. The article discusses the results of preliminary tests being a prologue to the optimization of the die-casting process parameters of complex aluminium bronze thick-walled bushs.

  5. An unconventional set-up for fluxless brazing of aluminium

    CERN Document Server

    Loos, Robert

    1999-01-01

    In order to successfully braze aluminium alloy assemblies without the use of oxide-removing fluxes, an evironment with very low contaminant level is mandatory. This is mostly achieved by using a vacuum furnace. Brazing under inert gas of sufficient purity is also possible. The method reported upon here makes use of a stainless steel bag which can enter a traditional air furnace. The bag is evacuated, giving a well distributed mechanical pressure on the parts to join. The intrinsic handicap of poor vacuum is compensated by regular inert gas flushing, even at high temperatures. The set-up works rather well, and the idea is believed to yield a valuable strategic and economic option, for the realization of special equipment as well as for prototyping work. We intend to use the principle for the CMS Preshower cooling screens.

  6. Strain rate sensitivity studies on bulk nanocrystalline aluminium by nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Varam, Sreedevi; Rajulapati, Koteswararao V., E-mail: kvrse@uohyd.ernet.in; Bhanu Sankara Rao, K.

    2014-02-05

    Nanocrystalline aluminium powder synthesized using high energy ball milling process was characterized by X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM). The studies indicated the powder having an average grain size of ∼42 nm. The consolidation of the powder was carried out by high-pressure compaction using a uni-axial press at room temperature by applying a pressure of 1.5 GPa. The cold compacted bulk sample having a density of ∼98% was subjected to nanoindentation which showed an average hardness and elastic modulus values of 1.67 ± 0.09 GPa and 83 ± 8 GPa respectively at a peak force of 8000 μN and a strain rate of 10{sup −2} s{sup −1}. Achieving good strength along with good ductility is challenging in nanocrystalline metals. When enough sample sizes are not available to measure ductility and other mechanical properties as per ASTM standards, as is the case with nanocrystalline materials, nanoindentation is a very promising technique to evaluate strain rate sensitivity. Strain rate sensitivity is a good measure of ductility and in the present work it is measured by performing indentation at various loads with varying loading rates. Strain rate sensitivity values of 0.024–0.054 are obtained for nanocrystalline Al which are high over conventional coarse grained Al. In addition, Scanning Probe Microscopy (SPM) image of the indent shows that there is some plastically flown region around the indent suggesting that this nanocrystalline aluminium is ductile.

  7. Die historiese betroubaarheid van die aartsvadervertellinge. 'n Beknopte bespreking van die huidige debat na aanleiding van die jongste publikasie

    Directory of Open Access Journals (Sweden)

    W. Vosloo

    1982-08-01

    Full Text Available Die afgelope twintig jaar was daar �n toenemende belangstelling in die aartsvadervertellinge in Genesis. Benewens die talle tydskrifartikels het skrywers soos die volgende ook boeke oor die onderwerp die lig laat sien: A. Parrot (1962, W. M. Clark (1964, R. Kilian (1966, R. E. Clements (1967, N. Lohfink (1967, H. Weidemann (1968, R. Martin-Achard (1969, T. L. Thompson (1974, J. van Seters (1975, J. P. Fokkelman (1975, C. Westermann (1976, R. Rendtorff (1977, J. Bright (1977, W. McKane (1979 en A. R. Millard en D. J. Wiseman (1980.

  8. 'n Kwalitatiewe ondersoek na die invloed van aspekte van die ...

    African Journals Online (AJOL)

    S Blignaut

    ISSN 0378-5254 Journal of Family Ecology and Consumer Sciences, Vol 26: No1, 1998. 15 ...... van byvoorbeeld die televisie en gedrukte media 'n invloed op die .... fashion promotion and advertising. New York. ... Consumer behaviour to-.

  9. Modeling the Mechanical Performance of Die Casting Dies

    Energy Technology Data Exchange (ETDEWEB)

    R. Allen Miller

    2004-02-27

    The following report covers work performed at Ohio State on modeling the mechanical performance of dies. The focus of the project was development and particularly verification of finite element techniques used to model and predict displacements and stresses in die casting dies. The work entails a major case study performed with and industrial partner on a production die and laboratory experiments performed at Ohio State.

  10. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    African Journals Online (AJOL)

    Test

    vergewe. Dit sou in orde gewees het as daar gestaan het, ReMomë- j^onta^is hepta?ds. wat die grieks is vir sewentig maal sewe. Die uitdrukking. heMom&ontabis heptd sien hoogswaarskynlik op Gen. 4 : 24 (LXX) waar. Lameg meedeel dat hy sewe-en-sewentig-maal gewreek sal word. Daar sit die Afr. Vert, die uitdrukking ...

  11. Development of the electron beam welding of the aluminium alloy 6061-T6 for the Jules Horowitz reactor

    International Nuclear Information System (INIS)

    Leblanc, Y.

    2013-01-01

    The aluminium alloy 6061-T6 has been selected for the construction of the Jules Horowitz's reactor vessel. This reactor vessel is pressurized and will be made through butt welding of ∼ 2 cm thick aluminium slabs. The electron beam welding process has been tested and qualified. It appears that this welding process allows: -) welding without pre-heating, -) vacuum welding, -) welding of 100% of the thickness in one passage, -) very low deforming welding process, -) very low density and very low volume of blow holes, -) weak ZAT (Thermal Affected Zones), and -) high reproducibility that permits automation. (A.C.)

  12. Film Presentation: Die Urknallmaschine

    CERN Multimedia

    Carolyn Lee

    2010-01-01

    Die Urknallmaschine, an Austrian film by Gerd Baldauf, narrated by Norbert Frischauf (Alpha Österreich - ORF, 2009).  In CERN’s gigantic complex particles are accelerated to almost the speed of light, brought to collision and made to divide into even smaller particles. Public opinion of CERN’s research is also divided. Sceptics fear that black holes may be created. Might the goal to study the origin of the world lead to its destruction? The Austrian researcher Norbert Frischauf worked at CERN for many years. With his guidance it is possible to explore the world’s largest research centre, get a glimpse of the fascinating work the scientists do there and take a crash course in particle physics. Die Urknallmaschine will be presented on Friday, 25 June from 13:00 to 14:00 in the Main Auditorium. Language: German

  13. Dying for security

    Directory of Open Access Journals (Sweden)

    Buchan, Bruce

    2011-01-01

    Full Text Available If political statements and media coverage are any guide, it seems Australians today are dying for security. At no other moment in our history has the spectre of war and terrorism so haunted popular, political and scholarly perceptions of Australia’s colonial past and of its geopolitical future. And yet, debates over colonial war or genocide and contemporary terrorism have been conducted in more or less complete isolation. In this article I argue that our contemporary obsession with ‘security’ is premised on the perennial threat of ‘insecurity’. This is the problem of in/security, and it has played a central role in the development of Western political thought. More importantly, its formulation in Western political thought provided a powerful justification for the violence of the early decades of Australia’s colonisation during which Indigenous Australians could also be said to have been dying for security.

  14. Dying for Security

    Directory of Open Access Journals (Sweden)

    Bruce Buchan

    2011-03-01

    Full Text Available If political statements and media coverage are any guide, it seems Australians today are dying for security. At no other moment in our history has the spectre of war and terrorism so haunted popular, political and scholarly perceptions of Australia’s colonial past and of its geopolitical future. And yet, debates over colonial war or genocide and contemporary terrorism have been conducted in more or less complete isolation. In this article I argue that our contemporary obsession with ‘security’ is premised on the perennial threat of ‘insecurity’. This is the problem of in/security, and it has played a central role in the development of Western political thought. More importantly, its formulation in Western political thought provided a powerful justification for the violence of the early decades of Australia’s colonisation during which Indigenous Australians could also be said to have been dying for security.

  15. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    African Journals Online (AJOL)

    Test

    aangetoon het, 'n huis in Kapernaum gehad en hierdie geskiedenis speel in Kapernaum of daar digby af. Jesus en sy dissipele het namelik, volgens 6:35 geland by Gennesaret, net suid van Kapernaum Die gevolgtrekking word ondersteun deur Joh. 6:17 waarvolgens die dissi pele na die spysiging op Kapernaum gevaar ...

  16. 'n Verkenning van die soorte vennootskappe in die Amerikaanse reg ...

    African Journals Online (AJOL)

    In die Amerikaanse literatuur word talle verwysings gevind na die vennootskap in mynbou ("mining partnership"), familievennootskap ("family partnership", vennootskap in vaste eiendom ("partnership in real estate") en vennootskap vir boerdery ("farming partnership"). Hierdie onderskeiding is primer gebaseer op die tipe ...

  17. Geslagsverskille in die ouditiewe ontlokte potensiaal van die brein

    Directory of Open Access Journals (Sweden)

    Anita D Stuart

    2006-10-01

    Full Text Available Gender differences in the auditory evoked potential of the brain. Based on literature indications of an association between temperament characteristics and the evoked potential of the brain, and indications of gender differences in certain temperament traits, the purpose of this study was to ascertain whether evoked responses also differentiated between the genders. A sample of 81 male and 210 female students was randomly selected. Two auditory evoked potential procedures were applied. The results indicated statistically significant differences in evoked potential responses between the genders. The results are interpreted against the background of sensory and neurological sources of the evoked potential responses and linked to the neurophysiological foundations of temperament. Opsomming: Gegrond op aanduidings in die literatuur van ’n assosiasie tussen temperamentskenmerke en die ontlokte potensiaal van die brein, sowel as aanduidings van geslagsverskille in sekere temperamentstrekke, was die doel van die huidige studie om te bepaal of ontloktepotensiaal-response ook tussen die geslagte onderskei. ’n Steekproef van 81 manlike en 210 vroulike studente is ewekansig geselekteer. Twee ouditiewe ontloktepotensiaal- prosedures is toegepas. Die resultate het op statisties beduidende verskille tussen die geslagte gedui. Die bevindinge word teen die agtergrond van die sensoriese en neurologiese oorsprong van ontloktepotensiaal–response geïnterpreteer en verbind aan die neurofisiologiese verankering van temperament.

  18. Die 'postmoderne' stempel in die Nuwe-Testamentiese hermeneutiek

    African Journals Online (AJOL)

    georiënteerde teorie en kritiek wat volgens Moore opbou tot 'n herhaling binne. Bybelnavorsing. Dit het reeds by Immanuel Kant begin. Sedert Kant is dit proble- maties cm die objek van kennis te beskou as iets wat kennis objektief in sigself bevat. Objektiwisme is prys gegee. Dialektiek het in die plek daarvan gekom. Die.

  19. duele verse sowel as die somtotaal die leser

    African Journals Online (AJOL)

    27 Jan 2006 ... selfs 'n landkaart afgedruk) terwyl dit ter- selfdertyd ver bo die lokale uitstyg. Die digter is sterk bewus van sy omgewing, geskiedenis en tradisies, maar veral van die algemene menslike kondisie wat binne hierdie referensiekader vergestalt word. Hy gebruik 'n bekende historiese slagveld as bundeltitel (en ...

  20. Die Leben Einsteins eine Reise durch die Geschichte der Physik

    CERN Document Server

    Fiami

    2005-01-01

    Jeder kennt die Namen Einstein, Newton oder Galilei. aber was weiss man über sie? Hier ein Porträt Einsteins anhand von sechs Meilensteinen aus der Geschichte der Physik. Einstein tritt auf als Protagonist in verschiedenen Epochen und bei verschiedenen Entdeckungen, die die Welt verändert haben.

  1. DIE KONINGSBEDE AS ELEMENT IN DIE KRONINGSRITUEEL. By ...

    African Journals Online (AJOL)

    Test

    Die offerfees te Gibeon was 'n plegtigheid, waaraan geheel Israel deelgeneem het. Die duisend. "brandoffers" wat sowel Kon. as Kron. vermeld, sal wel opgevat moet word as „brandoffers en dankoffers", sodat daar vir die aanwesiges. *n groot feesmaaltyd aangerig is, vgl. I Kon. 3:15. n Sodanige maal- tyd verbind vors en ...

  2. Ruimtelike beplanning: die rol van die stads - en streeksbeplanner ...

    African Journals Online (AJOL)

    Ruimtelike beplanning: die rol van die stads - en streeksbeplanner in die saw. R Erasmus. Abstract. Since 1978 regional and town planners are employed in the SADF on a permanent basis as well as in the capacity of national service men. These men are all academically qualified and as such satisfy a need that developed ...

  3. n opinie oor die behaviouristiese siening versus die fenomenologie ...

    African Journals Online (AJOL)

    verband die eksperimente van Pavlov, Thorndike,. Skinner, Tolmann en Hull.) Fenomenologie. Die fenomenologie is 'n essensie-openbarende denkrigting. Dit impliseer'n denkende soektog na dit wat 'n besondere verskynsel of werklikheid maak juis dit wat dit is en nie iets anders nie. In die fenomenologiese antropologie ...

  4. Aluminium in brain tissue in familial Alzheimer's disease.

    Science.gov (United States)

    Mirza, Ambreen; King, Andrew; Troakes, Claire; Exley, Christopher

    2017-03-01

    The genetic predispositions which describe a diagnosis of familial Alzheimer's disease can be considered as cornerstones of the amyloid cascade hypothesis. Essentially they place the expression and metabolism of the amyloid precursor protein as the main tenet of disease aetiology. However, we do not know the cause of Alzheimer's disease and environmental factors may yet be shown to contribute towards its onset and progression. One such environmental factor is human exposure to aluminium and aluminium has been shown to be present in brain tissue in sporadic Alzheimer's disease. We have made the first ever measurements of aluminium in brain tissue from 12 donors diagnosed with familial Alzheimer's disease. The concentrations of aluminium were extremely high, for example, there were values in excess of 10μg/g tissue dry wt. in 5 of the 12 individuals. Overall, the concentrations were higher than all previous measurements of brain aluminium except cases of known aluminium-induced encephalopathy. We have supported our quantitative analyses using a novel method of aluminium-selective fluorescence microscopy to visualise aluminium in all lobes of every brain investigated. The unique quantitative data and the stunning images of aluminium in familial Alzheimer's disease brain tissue raise the spectre of aluminium's role in this devastating disease. Copyright © 2016 The Authors. Published by Elsevier GmbH.. All rights reserved.

  5. Die Vier Typen von Projektmanagern

    DEFF Research Database (Denmark)

    Lund Pedersen, Carsten; Ritter, Thomas

    2018-01-01

    Bevor Sie einem Mitarbeiter die Leitung eines Projekts anvertrauen, sollten Sie sich über dessen Managementstil klar werden. Passt dieser nicht zur Art des Vorhabens, wird er scheitern. So treffen Sie die richtige Wahl....

  6. Die historiese Jesus as wondenverker

    African Journals Online (AJOL)

    Biblical Association, te wete 'The social sciences and second Testament exegesis'. John Pilch is die leier van die Society of Biblical Literature se 'Social sciences and ..... Hollenbach, P 1982. ... Stauffer, E 1982. Jesus ... London: Collins.

  7. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (paluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. A Bimetallic Aluminium(Salphen) Complex for the Synthesis of Cyclic Carbonates from Epoxides and Carbon Dioxide.

    Science.gov (United States)

    Wu, Xiao; North, Michael

    2017-01-10

    A bimetallic aluminium(salphen) complex is reported as a sustainable, efficient and inexpensive catalyst for the synthesis of cyclic carbonates from epoxides and carbon dioxide. In the presence of this complex and tetrabutylammonium bromide, terminal and internal epoxides reacted at 50 °C and 10 bar carbon dioxide pressure to afford their corresponding cyclic carbonates in yields of 50-94 % and 30-71 % for terminal and internal cyclic carbonates, respectively. Mechanistic studies using deuterated epoxides and an analogous monometallic aluminium(salphen) chloride complex support a mechanism for catalysis by the bimetallic complex, which involves intramolecular cooperative catalysis between the two aluminium centres. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Precision die design by the die expansion method

    CERN Document Server

    Ibhadode, A O Akii

    2009-01-01

    This book presents a new method for the design of the precision dies used in cold-forging, extrusion and drawing processes. The method is based upon die expansion, and attempts to provide a clear-cut theoretical basis for the selection of critical die dimensions for this group of precision dies when the tolerance on product diameter (or thickness) is specified. It also presents a procedure for selecting the minimum-production-cost die from among a set of design alternatives. The mathematical content of the book is relatively simple and will present no difficulty to those who have taken basic c

  10. Die Dokter-Pasient Rolverwantskap

    African Journals Online (AJOL)

    17 Aug 1974 ... en as sodanig 'n ral sped in die persoon se siektegedrag en uiteindelike patroon van hulpsoeke. SIEKEROL EN SOSIALISERING IN DIE. PASIENTROL ..... more cumulative, resulting in a more gradual social and professional maturation.' Vit die voorafgaande word dit duidelik dat Dewy se pragmatiese ...

  11. prosesseringsmetodes op die voedingswaarde van

    African Journals Online (AJOL)

    gebring is, kon geen betekenisvolle verskille tussen die drie monsters gevind word nie. Volgens Opstvedt (1976) kan ME waardes ook dien as 'n kriteria van proteien- kwaliteit, hoofsaaklik a.g.v. die verhoogde stikstofuit- skeiding in die urine wat sal plaasvind a.g.v. beskadiging van aminosure. De Groote (1968) het gevind ...

  12. DIE SAW SE ROL IN SWA

    African Journals Online (AJOL)

    wei die verdediging van die landsgrense teen 'n vyand wat die orde, gesag, vrede, stabiliteit en welvaart in Suidwes-Afrika en die Republiek van. Suid-Afrika wil vernietig. Hierdie oorlog moet nie ge'lsoleerd gesien word nie, maar in perspektief geplaas word teen die agtergrond van 'n nag groter konflik, naamlik die van die ...

  13. Die Subjektiewe en Objektiewe doelwitte van Arbeid

    Directory of Open Access Journals (Sweden)

    T. H. Veldsman

    1982-11-01

    Die artikel gee aandag aan die subjektiewe en objektiewe doelwitte van arbeid. Hul plek en funksie binne 'n voorgestelde geïntegreerde motiveringsmodel word eerstens aangedui. Vervolgens word die verwantskap tussen die twee doelwitte uitgelig, gevolg deur 'n bespreking van die aard van die objektiewe doel. Laastens word die invloed van moderne arbeid op hierdie doelwitte uitgestippel.

  14. DIE EKSISTENSIEFILOSOFIE VAN KARL JASPERS. ENKELE ...

    African Journals Online (AJOL)

    Test

    Kierkegaard en Nietzsche, Max Weber en Dilthey, om maar enkeles te noem, en 5.) Jaspers se persoonlike beskouing oor die roe ping en die taak van die Filosofie, sy aanvoeling van die filosofiese problematiek en sy grondhouding teenoor die eksistensiële verbonden- hede. Die woord van Fichte, naamlik dat die Filosofie ...

  15. Formation of aluminium nitride and segregation of Cu impurity atoms in aluminium implanted by high dose nitrogen ions

    International Nuclear Information System (INIS)

    Lin Chenglu; Hemment, P.L.F.; Li Jinhua; Zou Shichang

    1994-01-01

    Aluminium films with a thickness of 7000 A (containing 0.85% copper) were deposited on silicon substrates. 400 keV N 2 + or 350 keV N + ions were implanted into the aluminium films or at the interface between the aluminium and silicon, respectively. Automatic spreading resistance (ASR), Fourier transform infrared spectroscopy (FTIR) and Rutherford backscattering (RBS) and channelling were used to characterize the formation of aluminium nitride and the depth distribution of the Cu impurity in the aluminium films after ion implantation and post-annealing. The formation of a stoichiometric AlN layer with high resistance was evident from ASR, RBS analysis and FTIR measurements by the presence of the absorption band at 650 cm -1 . When the implanted nitrogen is near the interface between the aluminium and silicon, a multilayer structure can be obtained, which consists of aluminium, aluminium nitride and the silicon substrate. Cu, which is a background impurity in the deposited aluminium films, segregated into the synthesised aluminium nitride during high dose nitrogen ion implantation. This is due to irradiation-induced segregation during ion implantation. (orig.)

  16. [Association between serum aluminium level and methylation of amyloid precursor protein gene in workers engaged in aluminium electrolysis].

    Science.gov (United States)

    Yang, X J; Yuan, Y Z; Niu, Q

    2016-04-20

    To investigate the association between serum aluminium level and methylation of the promoter region of amyloid precursor protein (APP)gene in workers engaged in aluminium electrolysis. In 2012, 366 electrolysis workers in an aluminium factory were enrolled as exposure group (working years >10 and age >40 years)and divided into low-exposure group and high-exposure group based on the median serum aluminium level. Meanwhile, 102 workers in a cement plant not exposed to aluminium were enrolled as control group. Graphite furnace atomic absorption spectrometry was used to measure serum aluminium level, methylation specific PCR was used to measure the methylation rate of the promoter region of APP gene, and ELI-SA was used to measure the protein expression of APP in lymphocytes in peripheral blood. The exposure group had a significantly higher serum aluminium level than the control group (45.07 μg/L vs 30.51 μg/L, P0.05). The multivariate logistic regression analysis showed that with reference to the control group, low aluminium exposure (OR=1.86, 95% CI 1.67~3.52)and high aluminium exposure (OR=2.98, 95% CI 1.97~4.15)were risk factors for a reduced methylation rate of the promoter region of APP gene. Reduced methylation of the promoter region of APP gene may be associated with increased serum aluminium level, and downregulated methylation of the promoter region of APP gene may accelerate APP gene transcription.

  17. High temperature internal friction in pure aluminium

    International Nuclear Information System (INIS)

    Aboagye, J.K.; Payida, D.S.

    1982-05-01

    The temperature dependence of internal friction of nearly pure aluminium (99.99% aluminium) has been carefully measured as a function of annealing temperature and hence grain size. The results indicate that, provided the frequency and annealing temperature are held constant, the internal friction increases with temperature until some maximum value is attained and then begins to go down as the temperature is further increased. It is also noted that the internal friction decreases with annealing temperature and that annealing time has the same effect as annealing temperature. It is also noted that the internal friction peak is shifted towards higher temperatures as annealing temperature is increased. It is surmised that the grain size or the total grain boundary volume determines the height of the internal friction curve and that the order-disorder transitions at the grain boundaries induced by both entropy and energy gradients give rise to internal friction peaks in polycrystals. (author)

  18. Mechanical properties of aluminium honeycomb impact limiters

    International Nuclear Information System (INIS)

    Maji, A.K.; Satpathi, D.; Donald, S.

    1992-01-01

    Aluminium honeycombs have been extensively used as impact limiters in nuclear waste transport casks. The mechanical behaviour of these shock absorbing materials was studied to develop an extensive experimental database. A series of tests were performed along various loading paths. Different densities of aluminium honeycombs were tested in different orientations. Static tests included uniaxial tension, uniaxial compression and torsion. Dynamic tests were conducted at different strain rates of up to 100 s -1 , to generate experimental data relevant to accident situations. Dynamic studies included the effects of specimen size and confinement. The purpose of using different loading paths was to generate an extensive experimental database which may also be used to develop constitutive models for these materials. Design charts were constructed which can be accessed by various cask designers to optimise and economise on cask development. (Author)

  19. Diagnostics of ytterbium/aluminium laser plasmas

    International Nuclear Information System (INIS)

    Bailey, J.; Lee, R.W.; Landen, O.L.; Kilkenny, J.D.; Lewis, C.L.; Busquet, M.

    1986-11-01

    Microdot spectroscopy was used to study the x-ray emission from laser-produced plasmas consisting of 10% ytterbium, 90% aluminium. Spectra were recorded with a space-resolving flat crystal (PET) mini-spectrometer in the 4.0-8.0 A range. The Janus research laser at LLNL irradiated the targets with green (0.53 μm) light in a 1 nsec pulse. The power density was varied between 4x10 13 and 3x10 14 W/cm 2 . The plasma electron density and temperature were determined from the aluminium XI, XII and XIII line emission. By examining correlations between changes in the plasma conditions with changes in the ytterbium spectra, we will determine the potential for using ytterbium line emission as a plasma diagnostic

  20. Characterization of nitrogen-ion-implanted aluminium

    International Nuclear Information System (INIS)

    Rauschenbach, B.; Breuer, K.; Leonhardt, G.

    1990-01-01

    Aluminium has been implanted with nitrogen ions at different temperatures. The implanted samples have been characterized by Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and electron energy-loss spectroscopy (EELS). Deconvolution procedures are needed to separate the influence of the ion sputter profiling by AES and XPS from the nitrogen-ion-beam-induced effects. The chemical state of Al, N, O and C was identified by deconvolution of the measured spectra. In general, there were double-peak structures observed for N 1s and O 1s, identified as contributions from nitrides and weakly bound nitrogen, and oxides and weakly bound oxygen, respectively. Auger analysis confirms the influence of the nitrogen ion fluence on the shape of the concentration distribution. The influence of temperature on the chemical state of implanted aluminium and on the concentration distribution is discussed. (orig.)

  1. Swedish research on aluminium reactor technology

    International Nuclear Information System (INIS)

    Forsen, Bjoern

    1960-02-01

    A historical survey of the work done in Sweden this subject is given in the first part of the paper. The second part is elevated to a brief outline of the authors view of the present status of corrosion theories for aluminium in high temperature water. A theory where the crystallization of boehemite from the barrier layer is considered as an important control of the corrosion reaction is presented

  2. Simulation of aluminium STIR casting technique

    International Nuclear Information System (INIS)

    Hafizal Yazid; Mohd Harun; Hanani Yazid; Abd Aziz Mohamed; Muhammad Rawi Muhammad Zain; Zaiton Selamat; Mohd Shariff Sattar; Muhamad Jalil; Ismail Mustapha; Razali Kasim

    2006-01-01

    In this paper, the objective is to determine the optimum impeller speed correlated with holding time to achieve homogeneous reinforcement distribution for a particular set of experimental condition. Attempts are made to simulate the flow behaviourof the liquid aluminium using FLUENT software. Stepwise impeller speed ranging from 50 to 300 rpm.with 2 impeller angle blades of 45 and 90 degree with respect to the rotational plane were used

  3. Swedish research on aluminium reactor technology

    Energy Technology Data Exchange (ETDEWEB)

    Forsen, Bjoern

    1960-02-15

    A historical survey of the work done in Sweden this subject is given in the first part of the paper. The second part is elevated to a brief outline of the authors view of the present status of corrosion theories for aluminium in high temperature water. A theory where the crystallization of boehemite from the barrier layer is considered as an important control of the corrosion reaction is presented.

  4. Aluminium phosphide poising: a case report

    International Nuclear Information System (INIS)

    Hirani, S.A.A.; Rahman, A.

    2010-01-01

    This paper reports the case of a family in which three children were presented at Emergency Room (ER) with poisoning after the use of a pesticide at home. Initially, the cases were managed as routine cases of organophosphorus poisoning; however, the death of two children made the health team members realise that the poison's effects were delayed and devastating. Later, the compound was identified as Aluminium Phosphide (ALP), and the life of the last surviving child in the family was saved. (author)

  5. Implementation of Video Monitoring In Aluminium Industry

    OpenAIRE

    Hedlund, Ann; Andersson, Ing-Marie; Rosén, Gunnar

    2015-01-01

    The aim was to evaluate results and experiences from development of new technology, a training program and implementation of strategies for the use of a video exposure monitoring method, PIMEX. Starting point of this study is an increased incidence of asthma among workers in the aluminium industry. Exposure peaks of fumes are supposed to play an important role. PIMEX makes it possible to link used work practice, use of control technology, and so forth to peaks. Nine companies participated in ...

  6. Complexometric determination of scandium and aluminium

    International Nuclear Information System (INIS)

    Tikhonov, V.N.

    1980-01-01

    Described is the complexometric determination of scandium and aluminium by the method of reverse titration of EDTA excess by indium salt solution in the presence of the xylenol orange indicator. For the method selectivity increase fluorides are used as a camouflage substance at low pH values (2.5-3.0). The excess fluoride-ions preventing titration are bound by boric acid. Y, Tb, Ti, Zr, Cu, Zn, V, Mo, Co, Cr prevent the determination of Sc and Al

  7. Ion beam analysis of aluminium in thin layers

    International Nuclear Information System (INIS)

    Healy, M.J.F.; Pidduck, A.J.; Dollinger, G.; Gorgens, L.; Bergmaier, A.

    2002-01-01

    This work quantifies aluminium in thin surface and near surface layers. In one example, the layer overlies a thin gallium nitride layer on an aluminium oxide substrate and in a second example the aluminium exists just below the surface of an indium arsenide substrate. The technique of non-Rutherford elastic backscattering of protons was used for the samples where aluminum in the layer of interest needed to be resolved from aluminium in the sapphire substrate and the results were corroborated at the Technische Universitaet Muenchen using heavy ion elastic recoil detection analysis. In the second example, where it was unnecessary to isolate the signal of aluminium in the layer of interest (as the substrate contained no aluminium), then the 27 Al(d,p 01 ) 28 Al nuclear reaction was used. The elastic proton scattering cross section of aluminum was found to vary very rapidly over the energy range of interest

  8. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

  9. What is the risk of aluminium as a neurotoxin?

    Science.gov (United States)

    Exley, Christopher

    2014-06-01

    Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

  10. GOLD PRESSURE VESSEL SEAL

    Science.gov (United States)

    Smith, A.E.

    1963-11-26

    An improved seal between the piston and die member of a piston-cylinder type pressure vessel is presented. A layer of gold, of sufficient thickness to provide an interference fit between the piston and die member, is plated on the contacting surface of at least one of the members. (AEC)

  11. Study on the planning of a demonstration plant for hydrogen fuel production by electrolysis using caching in salt caverns under pressure; Studie ueber die Planung einer Demonstrationsanlage zur Wasserstoff-Kraftstoffgewinnung durch Elektrolyse mit Zwischenspeicherung in Salzkavernen unter Druck

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-02-05

    In a two year research project the long-term storage of hydrogen as energy carrier has been assessed in detail for large renewable electricity quantities in underground storage caverns in Germany. Next to a regions analysis for potential storage sites, the benchmarking against other large scale storage concepts, a comparative and perspective analysis of alkaline and PEM-electrolysers also potential business cases for Power-to-Hydrogen in the mobility sector as well as for the chemical, electricity and natural gas industry have been analysed. [German] Durch den geplanten Ausbau der Stromerzeugung aus fluktuierenden, erneuerbaren Energien in Deutschland ruecken Speichertechnologien fuer elektrische Energie immer staerker in den Fokus des industriellen und politischen Interesses. Eine vielversprechende Moeglichkeit fuer eine Langzeitspeicherung bei hohen Anteilen von Wind- und Photovoltaikanlagen sind Speichertechnologien wie die Wasserstoffspeicherung mit Hilfe von Wasserelektrolyseuren. Diese koennen erneuerbaren Strom in grossen Mengen und bei entsprechender Steuerung selektiv in Zeiten mit hohem Dargebot z.B. an Windstrom chemisch speichern. Der gespeicherte Wasserstoff kann dann entweder zu einem spaeteren Zeitpunkt wieder rueckverstromt oder direkt stofflich verwertet werden, z.B. als Kraftstoff fuer den Verkehrssektor, als chemischer Rohstoff oder fuer den Hausenergiebereich durch Einspeisung in das Erdgastransportnetz. Thema der vorliegenden Studie sind Analysen und Planungen fuer die Erprobung des Gesamtsystems ''Wasserstoff-Elektrolyse-Speicherung'' in energiewirtschaftlich relevanten Dimensionen. Dazu werden mit einem neuen Ansatz techno-oekonomische Entwicklungspfade fuer Wasserstoff-Systeme unterschiedlicher Groesse und Technologien charakterisiert und technologische Risiken bei der Realisierung dieser Systeme identifiziert und bewertet. Diese Arbeiten werden ergaenzt durch Arbeiten auf dem Gebiet der Salzkavernenspeicherung in Form

  12. Dying with dignity.

    Science.gov (United States)

    Madan, T N

    1992-08-01

    Death is a theme of central importance in all cultures, but the manner in which it is interpreted varies from society to society. Even so, traditional cultures, including Christian, Hindu and Jain religious traditions, exhibited a positive attitude to death and did not look upon it in a dualistic framework of good vs bad, or desirable vs undesirable. Nor was pessimism the dominant mood in their thinking about death itself. A fundamental paradigm shift occurred in the West in the eighteenth century when death was desacralized and transformed into a secular event amenable to human manipulation. From those early beginnings, dying and death have been thoroughly medicalized and brought under the purview of high technology in the twentieth century. Once death is seen as a problem for professional management, the hospital displaces the home, and specialists with different kinds and degrees of expertise take over from the family. Everyday speech and the religious idiom yield place to medical jargon. The subject (an ageing, sick or dying person) becomes the object of this make-believe yet real world. As the object of others' professional control, he or she loses the freedom of self-assessment, expression and choice. Or, he or she may be expected to choose when no longer able to do so. Thus, not only freedom but dignity also is lost, and lawyers join doctors in crisis manipulation and perpetuation. Although the modern medical culture has originated in the West, it has gradually spread to all parts of the world, subjugating other kinds of medical knowledge and other attitudes to dying and death.(ABSTRACT TRUNCATED AT 250 WORDS)

  13. Modelling of heterogeneous clustering in aluminium

    International Nuclear Information System (INIS)

    Smith, A.E.; Bourgeois, L.; Nie, J.-F.; Muddle, B.C.

    2003-01-01

    Full text: Ab initio modelling of heterogeneous clustering in aluminium has been carried out in order to study the precipitation hardening of alloys. This process is based on the addition of small amounts of solute element to the pure metal. With increasing computational power, atomic scale effects can now be better simulated to determine the nature of the hardening mechanism. Comparisons are made between results obtained from two computational packages. These are the Linear Augmented Plane Wave WEEN2K and the plane wave pseudopotential density functional theory package fhi98md. The study of the optimal geometry of very small size clusters inside aluminium has begun with the testing of initial convergence conditions by determination of binding energies for a variety of super cell sizes of the aluminium host crystal. These are compared with total energy calculations for small size precipitates of copper and transition metals of fixed geometry. Such local optimal determinations are seen as precursors to full Monte Carlo calculations of the notional best local geometry for larger precipitates

  14. Grain distinct stratified nanolayers in aluminium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Donatus, U., E-mail: uyimedonatus@yahoo.com [School of Materials, The University of Manchester, Manchester, M13 9PL, England (United Kingdom); Thompson, G.E.; Zhou, X.; Alias, J. [School of Materials, The University of Manchester, Manchester, M13 9PL, England (United Kingdom); Tsai, I.-L. [Oxford Instruments NanoAnalysis, HP12 2SE, High Wycombe (United Kingdom)

    2017-02-15

    The grains of aluminium alloys have stratified nanolayers which determine their mechanical and chemical responses. In this study, the nanolayers were revealed in the grains of AA6082 (T6 and T7 conditions), AA5083-O and AA2024-T3 alloys by etching the alloys in a solution comprising 20 g Cr{sub 2}O{sub 3} + 30 ml HPO{sub 3} in 1 L H{sub 2}O. Microstructural examination was conducted on selected grains of interest using scanning electron microscopy and electron backscatter diffraction technique. It was observed that the nanolayers are orientation dependent and are parallel to the {100} planes. They have ordered and repeated tunnel squares that are flawed at the sides which are aligned in the <100> directions. These flawed tunnel squares dictate the tunnelling corrosion morphology as well as appearing to have an affect on the arrangement and sizes of the precipitation hardening particles. The inclination of the stratified nanolayers, their interpacing, and the groove sizes have significant influence on the corrosion behaviour and seeming influence on the strengthening mechanism of the investigated aluminium alloys. - Highlights: • Stratified nanolayers in aluminium alloy grains. • Relationship of the stratified nanolayers with grain orientation. • Influence of the inclinations of the stratified nanolayers on corrosion. • Influence of the nanolayers interspacing and groove sizes on hardness and corrosion.

  15. Sal die ‘ewolusie’ vanaf biologie na lewenswetenskappe ‘uitsterwing’ van die vakgebied voorkom?

    Directory of Open Access Journals (Sweden)

    Johanna G. Ferreira

    2012-03-01

    Full Text Available In hierdie artikel word die wysiging van die skoolvak van ‘biologie’ na ‘lewenswetenskappe’ bespreek, asook die gepaardgaande en verwagte implikasies van die verandering. Die vraag word gestel of die beoogde wysiging wel noemenswaardig is en of dit enigsins ‘n verskil aan die dalende belangstelling in die lewenswetenskappe op tersiêre vlak sal maak. Die wysigings in die nuwe kurrikula verhoog die relevansie van die vakinhoud vir leerders en vir die gemeenskap, maar sekere kwessies kry nie aandag nie. Voorstelle word gemaak om die kurrikulum te wysig en onderrigmetodes aan te pas om die nodige vaardighede by leerders te vestig.

  16. enkele fasette van die problematiek van die akademikus by die skryf

    African Journals Online (AJOL)

    Om verskeie redes het dit van die allergrootste belong geword dot 'n his- tories korrekte, wetenskaplike weerga- we van bogenoemde gebeure opge- teken moet word. Die sluier, in sommige gevalle am logiese redes toegepas, moes eenvoudig gelig word am gebeure wat die gewone man op stroot in Suid-Afrika dikwels ...

  17. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    Directory of Open Access Journals (Sweden)

    B. Bobic

    2010-03-01

    Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

  18. Multiply-negatively charged aluminium clusters and fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Noelle

    2008-07-15

    Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

  19. The aluminium content of infant formulas remains too high.

    Science.gov (United States)

    Chuchu, Nancy; Patel, Bhavini; Sebastian, Blaise; Exley, Christopher

    2013-10-08

    Recent research published in this journal highlighted the issue of the high content of aluminium in infant formulas. The expectation was that the findings would serve as a catalyst for manufacturers to address a significant problem of these, often necessary, components of infant nutrition. It is critically important that parents and other users have confidence in the safety of infant formulas and that they have reliable information to use in choosing a product with a lower content of aluminium. Herein, we have significantly extended the scope of the previous research and the aluminium content of 30 of the most widely available and often used infant formulas has been measured. Both ready-to-drink milks and milk powders were subjected to microwave digestion in the presence of 15.8 M HNO3 and 30% w/v H2O2 and the aluminium content of the digests was measured by TH GFAAS. Both ready-to-drink milks and milk powders were contaminated with aluminium. The concentration of aluminium across all milk products ranged from ca 100 to 430 μg/L. The concentration of aluminium in two soya-based milk products was 656 and 756 μg/L. The intake of aluminium from non-soya-based infant formulas varied from ca 100 to 300 μg per day. For soya-based milks it could be as high as 700 μg per day. All 30 infant formulas were contaminated with aluminium. There was no clear evidence that subsequent to the problem of aluminium being highlighted in a previous publication in this journal that contamination had been addressed and reduced. It is the opinion of the authors that regulatory and other non-voluntary methods are now required to reduce the aluminium content of infant formulas and thereby protect infants from chronic exposure to dietary aluminium.

  20. Improvement of photodynamic activity of aluminium sulphophthalocyanine due to biotinylation

    Science.gov (United States)

    Meerovich, Irina G.; Jerdeva, Victoria V.; Derkacheva, Valentina M.; Meerovich, Gennadii A.; Lukyanets, Eugeny A.; Kogan, Eugenia A.; Savitsky, Alexander P.

    2003-09-01

    The photodynamic activity of dibiotinylated aluminium sulphophthalocyanine in vitro and in vivo were studied. It was obtained that in vitro dibiotinylated aluminium sulphophthalocyanine provides the effective damage of small cell lung carcinoma OAT-75. In vivo dibiotinylated aluminium sulphophthalocyanine causes destruction of tumor (Erlich carcinoma), results in total necrosis of tumor tissue and expresses vascular damage (trombosis and destruction of vascular walls) even in concentration 0.25 mg/kg of a body weight.

  1. Remediation of phosphate-contaminated water by electrocoagulation with aluminium, aluminium alloy and mild steel anodes.

    Science.gov (United States)

    Vasudevan, Subramanyan; Lakshmi, Jothinathan; Jayaraj, Jeganathan; Sozhan, Ganapathy

    2009-05-30

    The present study provides an electrocoagulation process for the remediation of phosphate-contaminated water using aluminium, aluminium alloy and mild steel as the anodes and stainless steel as the cathode. The various parameters like effect of anode materials, effect of pH, concentration of phosphate, current density, temperature and co-existing ions, and so forth, and the adsorption capacity was evaluated using both Freundlich and Langmuir isotherm models. The adsorption of phosphate preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules. The results showed that the maximum removal efficiency of 99% was achieved with aluminium alloy anode at a current density of 0.2 A dm(-2), at a pH of 7.0. The adsorption process follows second-order kinetics.

  2. Die Defects and Die Corrections in Metal Extrusion

    Directory of Open Access Journals (Sweden)

    Sayyad Zahid Qamar

    2018-05-01

    Full Text Available Extrusion is a very popular and multi-faceted manufacturing process. A large number of products for the automotive, aerospace, and construction sectors are produced through aluminum extrusion. Many defects in the extruded products occur because of the conditions of the dies and tooling. The problems in dies can be due to material issues, design and manufacturing, or severe usage. They can be avoided by maintaining the billet quality, by controlling the extrusion process parameters, and through routine maintenance. Die problems that occur on a day-to-day basis are mostly repairable and are rectified through various types of die correction operations. These defects and repair operations have not been reported in detail in the published literature. The current paper presents an in-depth description of repairable die defects and related die correction operations in metal extrusion. All major die defects are defined and classified, and their causes, preventive measures, and die correction operations are described. A brief frequency-based statistical study of die defects is also carried out to identify the most frequent die corrections. This work can be of direct benefit to plant engineers and operators and to researchers and academics in the field of metal extrusion.

  3. Studies of free field and confined explosions of aluminium enriched RDX compositions

    Energy Technology Data Exchange (ETDEWEB)

    Trzcinski, Waldemar A.; Cudzilo, Stanislaw; Paszula, Jozef [Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland)

    2007-12-15

    Research on the effect of aluminium contents and its particle size on free field and confined explosions characteristics of RDX-based compositions containing 15-60% aluminium was carried out. Parameters of blast waves produced by charges of the investigated explosives detonating in an open space were measured by the use of piezoelectric gauges. Simultaneously, photodiode set-ups were used to measure light output of the detonating charges. Quasi-static pressure measurements were conducted in steel chambers of 0.15 and 7 m{sup 3} volume filled with air. Moreover, the heat of detonation was measured with a calorimetric set in a 5.6 dm{sup 3} bomb filled with argon. The results of QSP and detonation heat measurements were compared with those obtained from thermochemical calculations. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  4. Die hermeneutiek van gereformeerde kerkreg

    Directory of Open Access Journals (Sweden)

    Andries le Roux du Plooy

    2012-10-01

    Full Text Available Die artikel het op die belangrikheid en noodsaaklikheid van ‘n hermeneutiek vir die gereformeerde kerkreg gefokus. Die kerkregtelike dokument wat besonderlik ter sake was, is die kerkorde van die Gereformeerde kerke in Suid-Afrika, met sy besondere band met die Dordtse kerkorde van 1618 en 1619. Agtereenvolgens is aandag gegee aan die volgende aspekte soos (1 die eiesoortige aard van ‘n kerkorde as ‘n teologiese dokument en teks, in onderskeiding van regsdokumente; (2 die aard van die hermeneutiek van kerkreg; (3 enkele teorieë oor die interpretasie of uitleg van tekste, veral regstekste en (4 normatiewe vooronderstellings en reëls vir die interpretasie en verstaan van die teks en artikels van die kerkorde asook besluite van kerklike vergaderinge. Die gevolgtrekking was dat weinig indringende navorsing gedoen is oor die saak van hermeneutiek vir kerkreg, hoewel dit noodsaaklik is. Duidelike hermeneutiese reëls is gesuggereer en verduidelik, wat sou kon meehelp dat kerke en kerklike vergaderinge die artikels van die kerkorde asook besluite en reglemente wat daarop berus het, kan interpreteer en toepas. The hermeneutics of reformed church polity. The article focused on the importance and urgency of a design for reformed hermeneutics on church polity. The Church Order referred to in the article is the Church Order of the Reformed Churches in South Africa, which are closely related to the Church Order of Dordt of 1618 and 1619. The following aspects received attention namely (1  the unique character of a Church Order, in comparison to and distinguished from legal documents and statutes; (2 the character and nature of hermeneutics of church polity; (3 theories of interpretation in the common law tradition and their relevance to church polity and (4 normative presuppositions and marks for the interpretation and understanding of the text and articles of the Church Order, as well as the resolutions of church assemblies. It was found that

  5. Argon-arc welding of heat resisting aluminium alloys

    International Nuclear Information System (INIS)

    Ryazantsev, V.I.; Fedoseev, V.A.

    1997-01-01

    Welding of aluminium heat resisting alloys of the Al-Cu-Mg system is studied. The hot-shortness of heat-resistant alloys M40, 1150 and 1151 are at the level of aluminium alloys 1201 and by 2-3 times lower as compared to the aluminium alloy AMg6. The M40, 1150 and 1151 alloys have unquestionable advantages against other know aluminium alloys only at temperatures of welded structures operation, beginning with 150-2000 deg C and especially at 250 deg C

  6. Beryllium electrodeposition on aluminium cathode from chloride melts

    International Nuclear Information System (INIS)

    Nichkov, I.F.; Novikov, E.A.; Serebryakov, G.A.; Kanashin, Yu.P.; Sardyko, G.N.

    1980-01-01

    Cathodic processes during beryllium deposition on liquid and solid aluminium cathodes are investigated. Mixture of sodium, potassium and beryllium chloride melts served as an lectrolyte. Beryllium ion discharge at the expense of alloy formation takes place at more positive potentials than on an indifferent cathode at low current densities ( in the case of liquid aluminium cathode). Metallographic analysis and measurements of microhardness have shown, that the cathodic product includes two phases: beryllium solid solution in aluminium and metallic beryllium. It is concluded, that aluminium-beryllium alloys with high cathodic yield by current can be obtained by the electrolytic method

  7. [Determination of aluminium in flour foods with photometric method].

    Science.gov (United States)

    Ma, Lan; Zhao, Xin; Zhou, Shuang; Yang, Dajin

    2012-05-01

    To establish a determination method for aluminium in flour foods with photometric method. After samples being treated with microwave digestion and wet digestion, aluminium in staple flour foods was determined by photometric method. There was a good linearity of the result in the range of 0.25 - 5.0 microg/ml aluminium, r = 0.9998; limit of detection (LOD) : 2.3 ng/ml; limit of quantitation (LOQ) : 7 ng/ml. This method of determining aluminium in flour foods is simple, rapid and reliable.

  8. Effect of smelt aluminium on mechanical properties of steels

    International Nuclear Information System (INIS)

    Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

    1987-01-01

    Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

  9. Investigation process of alcoholysis of hydride aluminium-adobe

    International Nuclear Information System (INIS)

    Numanov, M.I.; Normatov, I.Sh.; Mirsaidov, U.M.

    2001-01-01

    Considering of that process of acid treatment of aluminium-adobe hydride realizes in the ethyl alcohol media it was necessary study the process of alcoholysis of AlH 3 and aluminium additives. In the end of article authors became to conclusion that deficiency of spontaneous alcoholysis of AlH 3 in adobe caused by protective action of fiber; solvate ability of LiCl and alkoxy aluminium hydride of lithium-LiCl·CO 2 H 5 OH, Li Al(OC 2 H 5 ) 4 ·nC 2 H 5 OH decreasing the expectancy of responding of alcohol with aluminium hydride

  10. Serum aluminium levels of workers in the bauxite mines.

    Science.gov (United States)

    de Kom, J F; Dissels, H M; van der Voet, G B; de Wolff, F A

    1997-01-01

    Aluminium is produced from the mineral bauxite. Occupational exposure is reported during the industrial processing of aluminium and is associated with pulmonary and neurotoxicity. However, data on exposure and toxicity of workers in the open bauxite mining industry do not exist. Therefore, a study was performed to explore aluminium exposure in employees involved in this bauxite mining process in a Surinam mine. A group of workers occupationally exposed to aluminium in an open bauxite mine were compared with a group of nonexposed wood processors. Serum aluminium was analyzed using atomic absorption spectrometry Data from the clinical chemistry of the blood and a questionnaire were used to explore determinants for aluminium exposure. No significant difference between serum aluminium in the exposed (4.4 +/- 2.0 micrograms/L, n = 27) and control group (5.1 +/- 1.5 micrograms/L, n = 27) was detected. For the serum concentration of the clinical chemical variables (calcium, citrate, and creatinine), a statistically significant difference was computed (p < or = 0.02) between the exposed and control group. All levels were slightly higher in the exposed group; no statistically significant correlations with serum aluminium were found. In this study, serum aluminium values were in the normal range, no significant difference between the groups could be detected despite long-term occupational exposure.

  11. Die verband tussen lokus van beheer en die werks prestasie van swart bemarkers in die lewensversekeringsbedryf

    Directory of Open Access Journals (Sweden)

    E. L. Coetzer

    1997-06-01

    Full Text Available The relationship between locus of control and the work performance of black marketers in the life assurance industry. The aim of the study was to establish the relationship between locus of control and the work performance of black marketers in the life assurance industry. These constructs were selected by virtue of the lack of empirical research regarding the assumed relationship between them. The Locus of Control Scale of Schepers (1995 was used for measuring locus of control. Work performance was measured by the commission earned per month by the marketer, the number of policies generated by the marketer, as well as the percentage of lapsed policies. The relevant measurements were obtained in respect of a sample of 149 black marketing personnel. The results indicated a modest but statistically significant relationship between external locus of control and the work performance of black marketers. Opsomming Die doel van die studie was om die verband tussen lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf te bepaal. Hierdie konstrukte is gekies op grond van die gebrek aan empiriese navorsing rakende die veronderstelde verband tussen genoemde konstrukte. Die Lokus van Beheer-vraelys van Schepers (1995 is in die meting van lokus van beheer gebruik. Werksprestasie is aan die hand van kommissie per maand verdien, aantal polisse gegenereer deur 'n bemarker en die persentasie vervalde polisse, gemeet. Die tersaaklike metinge is verkry ten opsigte van 'n steekproef van 149 swart bemarkers. Die resultate toon 'n klein, dog statisties beduidende verband tussen eksterne lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf.

  12. Is die ortodoksie se verstaan van die sondeval belemmerend vir die gesprek tussen teologie en natuurwetenskap?

    Directory of Open Access Journals (Sweden)

    Johan Buitendag

    2012-11-01

    Full Text Available In hierdie artikel is betoog dat die Gereformeerde Ortodoksie se begrip van die sondeval ’n  belemmering  was  vir  die  gesprek  tussen  teologie  en  natuurwetenskap.  Die  rede hiervoor was dat dit ten eerste ’n bepaalde verstaan van liniêre tyd nahou en ten tweede dat dit ’n bonatuurlike ingryp veronderstel het. Albei hierdie aspekte het die debat onnodig problematiseer. Die argument is ontwikkel deur eerstens die probleem te definieer, gevolg deur ’n uiteensetting van die standpunte van Augustinus en Calvyn onderskeidelik oor die sondeval. As ’n heuristiese sleutel is die konsepte van infralapsarisme en supralapsarisme aangewend om die tema te ontleed. Die artikel is afgesluit met die oortuiging dat die imago Dei ’n beliggaamde menslike persoon is wat biologies in die geskiedenis in terme van selfbewussyn en morele verantwoordelikheid ontluik het. Is the Orthodoxy’s notion of the Fall inhibitory for the dialogue between theology and science? In this article it was argued that the Reformed Orthodoxy’s interpretation of the Fall had become an impediment in the dialogue between theology and science. The reason was that it assumed firstly a specific understanding of linear time and secondly a metaphysical intervention. Both events were unnecessarily problematising the debate. The argument was deployed by stating the problem, followed by an exposition of the views of Augustine and Calvin on the Fall. As a heuristic key, the concepts of infralapsarism and supralapsarism were applied respectively to analyse the topic. The article concluded with the conviction that the imago Dei is an embodied human person that had biologically emerged in history as a center of self-awareness, and moral responsibility.

  13. Dielectric aluminium phosphate thin films. Couches minces dielectriques de phosphate d'aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Daviero, S. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Avinens, C. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Ibanez, A. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Giuntini, J.C. (Lab. Physicochimie des Materiaux Solides, 34 -Montpellier (France)); Philippot, E. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France))

    1993-04-01

    Aluminium phosphate thin films on silicium substrate have been carried out from tributylphosphate and aluminium acetylacetonate precursors in solution through the ''pyrosol'' process. It can be observed a large range of chemical analysis in terms of experimental conditions. These thin films have been characterized by X-ray diffraction and infrared spectrometry. Their electrical characteristics, defined from direct current and alternative current measurements, are quite different to those of the crystallized phosphate and can be explained by P-O and Al-O ''dangling bond'' existence. (orig.).

  14. Sedimentêre omgewings van die Inhaca-eilandstelsel met spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente

    Directory of Open Access Journals (Sweden)

    Marieke Peché

    2011-09-01

    Full Text Available Die Inhaca-eilandstelsel is geleë langs die suidooskus van Mosambiek. Die oostekant van die stelsel grens aan die Indiese Oseaan en die westekant aan die Baai van Maputo. Hierdie eilandstelsel bestaan uit Inhaca- en Portugese eiland, asook ’n groep sandbanke wat van die noordlike punt van Inhaca na Portugese eiland strek. Die doel van hierdie studie is om die verskillende moderne en oer-sedimentêre omgewings op die eilandstelsel te identifiseer en te beskryf, die invloed van getye en golfaksie op die moderne sedimentêre omgewing vas te stel en die geochemiese en petrografiese samestelling van die geologiese eenhede te bepaal.

  15. Aluminium cables in automotive applications : Prestudy of aluminium cable uses in Scania products&Failure analysis and evaluation

    OpenAIRE

    Man, Yu

    2016-01-01

    The increasing demand of light constructed vehicles as well as soaring price of copper metal owing to limited nature resources have been promoting the use of aluminium metal as an alternative conductor of automotive cables. This thesis work is to lay theoretical foundations for further research and development regarding the introduction of new automotive cables i.e. aluminium cables. Current application of automotive aluminium cables in automotive industry as well as failure analysis and eval...

  16. Die vangnet van die woord: forensies-linguistiese getuienis in 'n ...

    African Journals Online (AJOL)

    Een van die redes daarvoor is waarskynlik die gepaardgaande sleurwerk verbonde aan die verwerking van die betrokke taaldata — iets wat egter deur die onlangse meteoriese vooruitgang in tegnologiese tegnieke op die agtergrond geskuif is en nuwe moontlikhede na vore laat kom het. In die lig van die kompleksiteit van ...

  17. het om die Woord van God aan die gemeente te bedien. A. D. P ont ...

    African Journals Online (AJOL)

    Test

    Sizoo vertel met die vlotheid van die ervare skrywer en die ver antwoordelikheid van die wetenskaplike ... Maar in stiptelike trou aan die feitelikheid, verlaat die skrywer hom uitsluitlik op die outentieke bronne om ... de leser; in sy rykdom van gegewens en wetenskaplike betroubaarheid kan dit met vrug gelees word deur die ...

  18. Die invloed van herbivorie en vuur op die oorlewing van sekere meerjarige kruide langs die Sabierivier, Kruger Nasionale Park

    Directory of Open Access Journals (Sweden)

    H. Myburgh

    2012-03-01

    Full Text Available Die groot vloede wat in die jaar 2000 in die Kruger Nasionale Park plaasgevind het, het dierivieroewerplantegroei versteur. Dit het die geleentheid gebied om heinings op te rig langsdie Sabierivier om herbivore uit sekere gebiede uit te sluit en sodoende die herstel van die rivieroewerekosisteme te monitor.

  19. Die heelal en sy onstaan (II

    Directory of Open Access Journals (Sweden)

    D. J. Van Rooy

    1952-03-01

    Full Text Available Ons kennis en wetenskap van die hemelliggame word volkome bepaal deur die lig wat ons van hulle ontvang, d.w.s. as ons die feite wat die Bybel daaromtrent meedeel, buite rekening laat.

  20. Versoening tussen leerders: Is parallelmediumskole die antwoord op die rassismeprobleem?

    OpenAIRE

    Du Plessis, Elize; Marais, Petro

    2017-01-01

    Die Suid-Afrikaanse Grondwet stel dit duidelik dat enige vorm van diskriminasie nie toegelaat mag word nie. In ons skole beteken dit dat elke leerder ʼn reg het op goeie opvoeding en ʼn veilige skoolomgewing. Die fokus van hierdie navorsing is gerig op bestaande parallelmediumskole. Die uiteindelike vraagstuk is dus hoe multikulturele onderwys bevorder word en hoe rassisme aangespreek kan word? As teoretiese raamwerk is Kohlsberg se kognitiewe ontwikkelingsbenadering en Whitehouse se univerele ...

  1. Die ontmaskering van die bose: Eksegetiese perspektiewe op ...

    African Journals Online (AJOL)

    p1243322

    2 Yarbro Collins (1983) bied tans nog die beste agtergrond vir 'n besinning oor geweld in ..... John's grammatical howlers are intentionally designed to alert listerners ..... 26 In die Nuwe Testament word Paul se snydende opmerking teenoor die Korintiërs as ..... rnt g0r`m nh8 ldfhrs`}m du sg}u fg}u + n2sh d/m sg>}} e`ql`jdh.

  2. Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

    Science.gov (United States)

    Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

    2015-10-01

    Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

  3. Die pastorale sielkundige as diakonale pastor

    Directory of Open Access Journals (Sweden)

    A. J. Smuts

    1985-08-01

    Full Text Available In die bedieningspatroon van die Ned. Geref. Kerk het die pastorale sielkundige die afgelope aantal jare steeds meer op die voorgrond begin tree. Hy is egter 'n problematiese figuur, wie se identiteit van meer as een kant onder bespreking is. In ander lande, selfs in die VSA waar die kerk veel gebruik maak van die sielkunde, is dit moeilik om 'n presiese parallel vir hom te vind. Sowel binne as buite die kerk word hy deur sommige bevraagteken. Daarom is dit noodsaaklik om vanuit die teologie te kyk na die werk wat hy doen.

  4. There is (still too much aluminium in infant formulas

    Directory of Open Access Journals (Sweden)

    Burrell Shelle-Ann M

    2010-08-01

    Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

  5. Effects of aluminium surface morphology and chemical modification on wettability

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

    2014-03-01

    Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

  6. Long-term effects of aluminium dust inhalation.

    Science.gov (United States)

    Peters, Susan; Reid, Alison; Fritschi, Lin; de Klerk, Nicholas; Musk, A W Bill

    2013-12-01

    During the 1950s and 1960s, aluminium dust inhalation was used as a potential prophylaxis against silicosis in underground miners, including in Australia. We investigated the association between aluminium dust inhalation and cardiovascular, cerebrovascular and Alzheimer's diseases in a cohort of Australian male underground gold miners. We additionally looked at pneumoconiosis mortality to estimate the effect of the aluminium therapy. SMRs and 95% CI were calculated to compare mortality of the cohort members with that of the Western Australian male population (1961-2009). Internal comparisons on duration of aluminium dust inhalation were examined using Cox regression. Aluminium dust inhalation was reported for 647 out of 1894 underground gold miners. During 42 780 person-years of follow-up, 1577 deaths were observed. An indication of increased mortality of Alzheimer's disease among miners ever exposed to aluminium dust was found (SMR=1.38), although it was not statistically significant (95% CI 0.69 to 2.75). Rates for cardiovascular and cerebrovascular death were above population levels, but were similar for subjects with or without a history of aluminium dust inhalation. HRs suggested an increasing risk of cardiovascular disease with duration of aluminium dust inhalation (HR=1.02, 95% CI 1.00 to 1.04, per year of exposure). No difference in the association between duration of work underground and pneumoconiosis was observed between the groups with or without aluminium dust exposure. No protective effect against silicosis was observed from aluminium dust inhalation. Conversely, exposure to aluminium dust may possibly increase the risk of cardiovascular disease and dementia of the Alzheimer's type.

  7. Digilanid C by die behandeling van hartlyers

    NARCIS (Netherlands)

    Snyman, Hendrik Willem

    1942-01-01

    In die voorafgaande word 'n literatuur studie oor die ontwikkeling en huidige stand van die chemie en farmakologie van die Digitalis purpurea en Digitalis lanata gegee, waarin spesiaal gelet word op die chemiese samestelling en farmakologiese aktiwiteit van die Digitalis lanata glikoside. Daarna

  8. HISTORIESE OORSIG VAN DIE ONTSTAAN EN ONTWIKKELING ...

    African Journals Online (AJOL)

    In 1933 belas Rykskanselier. Hitler vir. Goering, Minister van Lugvaart, in die geheim met die skepping van die Luftwaffe. Die basis in Rusland is gesluit en toekomstige vlieeniers is nou in die geheim na Italie waar hulle elke aspek van moderne oorlog- voering oefen en die Blitzkrieg-gedagte, deur op ondersteuning van 'n.

  9. EUNUG IN DIE ANTIEKE NABYE OOSTE

    African Journals Online (AJOL)

    rang. In Assiries beteken die woord “hoof-eunug”. Soos reeds vermeld (by 2), vorm die eunug 'n belangrike deel van die Assiriese burokrasie. Dokumente dui aan ... rang in die Babiloniese weermag, en so 'n amptenaar het saam met die rabsag ..... baie laat, in die inter-testamentêre periode, gebruik is vir 'n gekastreerde.

  10. Mechanical properties of plasma-sprayed layers of aluminium and aluminium alloy on AZ 91

    Czech Academy of Sciences Publication Activity Database

    Kubatík, Tomáš František; Ctibor, Pavel; Mušálek, Radek; Janata, Marek

    2017-01-01

    Roč. 51, č. 2 (2017), s. 323-327 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : plasma spraying of aluminium * adhesion of coating * wear * magnesium alloy AZ91 Subject RIV: JG - Metallurgy OBOR OECD: Materials engineering Impact factor: 0.436, year: 2016

  11. Irradiation effects on the mechanical properties of aluminium and the structural integrity of aluminium reactor components

    International Nuclear Information System (INIS)

    Harrison, R.P.; McDonald, N.R.; Mitchell, D.R.G.; Hellier, A.K.; Stathers, P.A.; Carr, D.G.; Ripley, M.I.

    2000-01-01

    The results of micro-structural and mechanical property studies on aluminum after being exposed to large fluences of neutrons are presented. These property changes are of importance in determining the structural integrity of the Australian HIFAR reactor aluminium tank, which in turn determines the lifetime of the reactor. (author)

  12. Die Transition zur pflegenden Tochter

    Directory of Open Access Journals (Sweden)

    Dagmar Dräger

    2004-11-01

    Full Text Available Das Buch aus der Reihe „Studien zur Gesundheits- und Pflegewissenschaft“ beschreibt den theoretischen Hintergrund, das methodische Vorgehen und die Ergebnisse einer biografischen Untersuchung, die sich dem Übergang von der Tochter zur pflegenden Tochter widmete. Grundlage der Publikation ist die Dissertation (2002 der Autorin. Mit der Berücksichtigung biographischer und familiärer Hintergründe wird eine neue Perspektive in der Forschung zu pflegenden Angehörigen eingenommen.

  13. Maintaining Low Voiding Solder Die Attach for Power Die While Minimizing Die Tilt

    Energy Technology Data Exchange (ETDEWEB)

    Hamm, Randy; Peterson, Kenneth A.

    2015-10-01

    This paper addresses work to minimize voiding and die tilt in solder attachment of a large power die, measuring 9.0 mm X 6.5 mm X 0.1 mm (0.354” x 0.256” x 0.004”), to a heat spreader. As demands for larger high power die continue, minimizing voiding and die tilt is of interest for improved die functionality, yield, manufacturability, and reliability. High-power die generate considerable heat, which is important to dissipate effectively through control of voiding under high thermal load areas of the die while maintaining a consistent bondline (minimizing die tilt). Voiding was measured using acoustic imaging and die tilt was measured using two different optical measurement systems. 80Au-20Sn solder reflow was achieved using a batch vacuum solder system with optimized fixturing. Minimizing die tilt proved to be the more difficult of the two product requirements to meet. Process development variables included tooling, weight and solder preform thickness.

  14. Neurokognitiewe integrasie en die leerproses

    Directory of Open Access Journals (Sweden)

    Du Preez, Johan J.

    1991-12-01

    Full Text Available The purpose of this article, "Neuro-cognitive integration and the learning process'; is to find principles and strategies for the development of brain potential and the optimal integration of subject matter. Eight neuro-cognitive systems are identified and their importance to the integration of subject matter is emphasized. These systems are cortical energy, coding, planning and controlling, as well as the verbal sequential, non-verbal holistic, physical-motor, social effective and the subconscious. The relevant principles and strategies can serve as basis for mainstream and special education, guidance as well as psychotherapy. Die doe! met hierdie artikel is om beginsels en strategiee te vind om breinpotensiaal te ontsluit en leerstof optimaal te integreer. Aan die hand van 'n neurokognitiewe model word 'n aantal beginsels en strategiee bespreek en die verband met die leerproses word aangetoon. Agt neurokognitiewe sisteme is gei'dentifiseer en die belangrike rot wat dit speel ten opsigte van die integrasie van leerstof word beklemtoon. Genoemde sisteme sluit die volgende in: kortikale energie, kodering, beplanning en kontrolering, asook die verbaal-sekwensiele, nieverbaal-holistiese, fisiek-motoriese, sosio-affektiewe en die subbewuste. Genoemde beginsels en strategiee kan oak dien as grondslag vir hoofstroomonderwys, spesialiseringsonderwys, voorligting sowel as psigoterapie.

  15. Combined Corrosion and Wear of Aluminium Alloy 7075-T6

    NARCIS (Netherlands)

    Liu, Y.; Mol, J.M.C.; Janssen, G.C.A.M.

    2016-01-01

    The aluminium alloy 7075-T6 is widely used in engineering. In some applications, like slurry transport, corrosion and abrasion occur simultaneously, resulting in early material failure. In the present work, we investigated the combined effect of corrosion and wear on the aluminium alloy 7075-T6. We

  16. Sol gel synthesis for preparation of yttrium aluminium garnet

    NARCIS (Netherlands)

    Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.; With, de G.; Terpstra, R.A.; Metselaar, R.

    1989-01-01

    Sol-gel—synthesis for preparation of pure yttrium aluminium garnet powder with small grain size is subject of this ongoing study. Starting materials were sulfates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3A1SO1Z) pH during hydrolysis as well as temperature during calcination and

  17. Three body abrasion of laser surface alloyed aluminium AA1200

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2012-06-01

    Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4 kW Nd:YAG laser to improve the abrasion wear resistance. Aluminium surfaces reinforced with metal matrix composites and intermetallic phases were achieved. The phases present depended...

  18. The effects of aluminium and selenium supplementation on brain ...

    African Journals Online (AJOL)

    This in vivo study was designed to investigate the potential of aluminium (Al), in the absence of added iron, to participate in either antioxidant or pro-oxidant events. Some markers of oxidative stress were determined in liver and brain of rats exposed to aluminium lactate, either alone or in the presence of dietary supplements ...

  19. Aluminium and Alzheimer's disease: the science that describes the link

    National Research Council Canada - National Science Library

    Exley, Christopher

    2001-01-01

    ... that has been encircled is the gene for the amyloid precursor protein. (Thanks to Walter Lukiw for supplying this information.) Aluminium and Alzheimer's Disease: The Science that Describes the LinkAluminium and Alzheimer's Disease The Science that Describes the Link Edited by Christopher Exley Birchall Centre for Inorganic Chemistry and Materials Scienc...

  20. An interesting and efficient green corrosion inhibitor for aluminium ...

    African Journals Online (AJOL)

    An interesting and efficient green corrosion inhibitor for aluminium from extracts of ... Journal Home > Vol 13, No 1 (2014) > ... possible applications in metal surface anodizing and surface coating in industries. Keywords: Moringa oleifera, Aluminium, Hydrochloric acid, Langmuir isotherm, Plant extracts, Corrosion inhibition ...

  1. Synthesis of aluminium nanoparticles by arc evaporation of an ...

    Indian Academy of Sciences (India)

    Administrator

    Abstract. Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on.

  2. Anodization of Aluminium using a fast two-step process

    Indian Academy of Sciences (India)

    283.6 eV. Keywords. Anodization; phosphoric acid; anodization time; anodized aluminium oxide; aluminium. ... of anodization.5–7 The AAO layer has a large band gap, good ..... transmittance increases as the anodised membrane is heated to ...

  3. Aluminium removal from water after defluoridation with the electrocoagulation process.

    Science.gov (United States)

    Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

    2015-01-01

    Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

  4. Spark counting technique with an aluminium oxide film

    International Nuclear Information System (INIS)

    Kawai, H.; Koga, T.; Morishima, H.; Niwa, T.; Nishiwaki, Y.

    1980-01-01

    Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm 2 . The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

  5. Neutron activation analysis of baths forming conversion layer on aluminium

    International Nuclear Information System (INIS)

    Szilagyi, Istvan; Maleczki, Emil; Bodizs, Denes

    1988-01-01

    Chromate layers were formed on the surface of aluminium using yellow and green chromating solutions. For the determination of the aluminium content neutron activation method was used. Nuclear effects disturbing the determination were eliminated by double irradiation technique. (author) 8 refs.; 4 figs

  6. An alternative design method for the double-layer combined die using autofrettage theory

    Directory of Open Access Journals (Sweden)

    C. Hu

    2017-08-01

    Full Text Available The double-layer combined die is used for its longer life in forging. Autofrettage is a well-known elastic–plastic technology that increases the durability of thick-walled cylinders. This study explores an alternative design method of the double-layer combined die using autofrettage theory. An analytical solution for the autofrettage process of the double-layer combined die is obtained based on Lamé's equation. The relationship between the autofrettage pressure and the yield radius of the die insert is obtained, and expressions of residual stresses and displacements, which are directly related to geometric parameters, material properties and internal pressure, are derived. The finite-element simulation of a specific case is performed, and good agreement between theoretical calculations and simulation results is found. Furthermore, the effects of important parameters, including the ratio of the plastic area and yield strength of the die insert and the outer diameters of the die insert and stress ring, on the autofrettage effect are investigated. Compared with the conventional combined die, the autofrettaged die can bear larger working pressure, as expected. The use of the autofrettaged die can reduce the amount of expensive material required for the die insert and the working space of the die set, which would benefit the practical forging process.

  7. Numerical optimization of die geometry in open die forging

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    This paper deals with numerical optimization of open die forging of large metallic ingots made by casting implying risk of defects, e.g. central pores. Different material hardening properties and die geometries are combined in order to investigate, which geometry gives rise to maximum closure...

  8. die geskiedenis van die saw gedenkteken te fort klapperkop militere ...

    African Journals Online (AJOL)

    As gevolg van enige optrede, op enige plek, te enige tyd, deur enige vyand van die RSA of deur enige terroris(te), insurgent(e) of ander persoon of persone wat die RSA en sy volkere kwaadgesind is. h. Binne twee jaar (vyfhondred-en-dertig dae) nadat hy/sy met 'n ongeskiktheids- pensioen uit diens getree het agv siekte,.

  9. Die adversatiewe stelsel van bewyslewering en die beste belang ...

    African Journals Online (AJOL)

    MJM Venter

    weeg. Hierdie vraag word teen die agtergrond daarvan beoordeel dat veral dispute ..... restructuring family into the highly polarized positions of court-based dispute resolution.16. Talle alternatiewe om tekortkominge in die adversatiewe proses te ..... De Jong M "Mediation and Other Appropriate Forms of Alternative Dispute.

  10. Die teologiese debat: Die waarde of betekenis daarvan

    African Journals Online (AJOL)

    Ego vero hoc libro non contuli sed asservi et assero, ac penes nullum vo- lo esse iudicium, sed omnibus suadeo, ut praestent obsequium. (M Luther, De servo arbitrio, 1525). 1. INLEIDING. In ons dae is dit hoe mode om oor alles debat te voer. Een van die towerwoorde van ons tyd, veral op die politiek-staatkundige terrein, ...

  11. Die konteks vir die keuse van geriefsvoedsel van bepaalde ...

    African Journals Online (AJOL)

    Seugnet

    70. Die konteks vir die keuse van geriefsvoedsel van bepaalde beroepsvroue *. Martha Kok en Priscilla Botha. ABSTRACT. The purpose of this research is to understand and describe the context in which career women choose, purchase and use convenience food (CF). A person is rarely isolated from or unaffected by.

  12. Die vlugtige taal van vergeet: Die metafoor by Breyten Breytenbach ...

    African Journals Online (AJOL)

    From his first book of poetry, die ysterkoei moet sweet (“the iron cow must sweat”, 1964), till his most recent one, die windvanger (“the windcatcher”, 2007), metaphor has been a central means towards the creation of meaning for Breytenbach. This article will investigate the use of metaphor particularly in this recent book.

  13. Friction stir welding of single crystal aluminium

    DEFF Research Database (Denmark)

    Fonda, Richard Warren; Wert, John A.; Reynolds, A.P.

    2007-01-01

    Friction stir welds were prepared in different orientations in an aluminium single crystal. The welds were quenched to preserve the microstructure surrounding the tool and then electron backscattered diffraction was used to reveal the generation of grain boundaries and the evolution...... of crystallographic texture around the tool in each weld. The extent of both dynamic recrystallisation and conventional recrystallisation varied considerably as a function of weld orientation. As the base plate begins to interact with the deformation field surrounding the tool, regions of the single crystal rotate...

  14. Structure of the aluminium-uranium eutectic

    International Nuclear Information System (INIS)

    Ambrozio Filho, F.; Vieira, R.R.

    1975-01-01

    The authors discuss the factors which might effect the eutectic structure, including external conditions during solidification as well as factors peculiar to each individual system. They studied the structure of the A1-U eutectic, consisting of the solid solution of uranium in aluminium and UA1 4 , as obtained in ingot moulds and by unidirectional solidification, and found a tendency for the structure to develop in a spiral, in the form of a rhombus. They discuss this structure in terms of certain variables with emphasis on the growth characteristics of the phases comprising the eutectic, the velocity of growth and thermal gradient in the liquid [pt

  15. Convenient synthesis of deuterated aluminium hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Pawelke, Roland H.; Felderhoff, Michael; Weidenthaler, Claudia [Max-Planck-Institut fuer Kohlenforschung, Kaiser-Wilhelm-Platz 1, 45470 Muelheim an der Ruhr (Germany); Schueth, Ferdi [Max-Planck-Institut fuer Kohlenforschung, Kaiser-Wilhelm-Platz 1, 45470 Muelheim an der Ruhr (Germany)], E-mail: schueth@mpi-muelheim.mpg.de

    2008-09-15

    We describe the ball-milling synthesis of alkali metal deuterides from commercial lithium aluminium deuteride. This reaction principle was exemplified by the mechanochemical synthesis of NaAlD{sub 4} and KAlD{sub 4}. NaAlD{sub 4} was prepared on the multi-gram scale by this procedure and purified by standard wet-chemical separation. Pure NaAlD{sub 4} was obtained and used for the synthesis of Ca(AlD{sub 4}){sub 2}. The formation of all products was verified by X-ray diffraction.

  16. Calculation of electron transmission through aluminium foil

    International Nuclear Information System (INIS)

    Abroyan, M.A.; Mel'ker, A.I.; Mikhajlin, A.I.; Sirotinkin, V.V.; Tokmakov, I.L.

    1987-01-01

    Calculated by Monte Carlo method energy and angular distributions of electrons transmitted through aluminium foil with 50 μm thickness are presented. 200-500 electron energy ranges and angles of electron incidence on foil from 0 to 40 deg C are considered. That allows to use results for more universal accelerator group, for example, for accelerators with scanning beam used in industry. The received values of angular and energy characteristics allow to increase essentially estimation accuracy of accelerator extraction devices and dose distribution on irradiating item

  17. Deviatoric response of the aluminium alloy, 5083

    Science.gov (United States)

    Appleby-Thomas, Gareth; Hazell, Paul; Millett, Jeremy; Bourne, Neil

    2009-06-01

    Aluminium alloys such as 5083 are established light weight armour materials. As such, the shock response of these materials is of great importance. The shear strength of a material under shock loading provides an insight into its ballistic performance. In this investigation embedded manganin stress gauges have been employed to measure both the longitudinal and lateral components of stress during plate impact experiments over a range of impact stresses. In turn, these results were used to determine the shear strength and to investigate the time dependence of lateral stress behind the shock front to give an indication of material response.

  18. CERN: very large magnet with aluminium winding

    Energy Technology Data Exchange (ETDEWEB)

    Wittgenstein, F.A.

    1984-10-25

    The construction of an octagonal solenoid from trapezoidal plates of Al, 6m long and 6cm thick, assembled by electron beam welding, for installation in a laboratory 50m underground is described. The objective is to create a field of 0.5T in a volume of 1000m/sup 3/ for the L3 particle detector of the LEP accelerator project. Principal dimensions and weights of the structure are given and its three stages of implementation are described, with reference to the contributions from the Swiss aluminium industry.

  19. Morphology of the aluminium-uranium eutectic

    International Nuclear Information System (INIS)

    Ambrozio Filho, F.; Vieira, R.R.

    1976-01-01

    The factors which might affect the eutectic structure including external condition during solidification as well as factors peculiar to each individual system is discussed. The structure of the Al-U eutectic, consisting of the solid solution of uranium in aluminium and UAl 4 , as obtained in ingot moulds and by unidirectional solidification. The extructure in terms of certain variables with emphasis on the growth characteristics of the phases comprising the eutectic the velocity of growth and thermal gradient in the liquid is also presented [pt

  20. The failure of aluminium nitride under shock

    International Nuclear Information System (INIS)

    Pickup, I.M.; Bourne, N.K.

    2002-01-01

    The shear strength of aluminium nitride has been measured over a range of impact stresses by measuring lateral stresses in plate impact experiments. The range of impact stress spanned several key shock thresholds for the material, pre and post Hugoniot elastic limit and up to values where the hexagonal to cubic phase transition starts. The shear strength measurements indicate significant inelastic damage at stress levels in excess of the HEL, but a significant recovery of strength at the highest impact stress was observed. This stress equates to the phase transition stress. The shear strength behaviour is compared to that of silicon carbide, which does not exhibit a phase change at these impact velocities