WorldWideScience

Sample records for aluminium aluminium oxide

  1. Dispersion strengthening of aluminium-aluminium-oxide products

    DEFF Research Database (Denmark)

    Hansen, Niels

    1970-01-01

    temperature and at 400°C is in agreement with Orowan's theory. The increase in flow stress at room temperature for strain values below 3 per cent was related to the plastic strain by the equation σ-σoy=k1ε 1/2, where σoy is the initial flow stress and where k1 increases for increasing volume fraction......The true stress-true strain curves at room temperature and at 400°C were determined for various types of aluminium-aluminium-oxide products containing from 0.2 to 4.7 weight per cent of aluminium oxide. The effect of particles on the initial flow stress and the flow stress for 0.2% offset at room...

  2. Refractory oxides containing aluminium and barium

    OpenAIRE

    Davies T.J.; Biedermann M.; Q-G. Chen; Emblem H. G.; Al-Douri W. A.

    1998-01-01

    Oxides containing aluminium and barium, optionally with chromium, are refractory with several possible industrial uses. A gel precursor of an oxide having the formula BaO.n(Al2xCr2yO3), where 1aluminium salt or a solution of an aluminium salt and a chromium III salt, then forming a gel which was fired to obtain the desired oxide. Filaments may be drawn as the gel is forming or extr...

  3. Spark counting technique with an aluminium oxide film

    International Nuclear Information System (INIS)

    Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm2. The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

  4. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy); Gorla, Leopoldo; Nessi, Simone; Grosso, Mario [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  5. Eu(III)-doped aluminium yttrium oxide

    International Nuclear Information System (INIS)

    In this work, we report the synthesis and the photoluminescence features of Eu(III)-doped yttrium-aluminium oxide obtained by non-hydrolytic sol-gel routes. After heating the powders above 600 deg C the XRD patterns show the presence of the Y4Al2O9 (YAM) and Y3Al5O12 (YAG) phases. At 800 and at 1500 deg C the PL spectra display the Eu(III) lines characteristic of the YAM monoclinic phase. The 5D0→7F2 transition is favored relatively to the 5D0→7F1 lines. However, at 1100 deg C the cubic YAG is the preferential phase and the 5D0→7F1 transition dominates the spectrum. The Eu(III) ions lie in a centro symmetrical site. The different solvents used in the sol-gel synthesis also change the relative proportion between these two phases. This is monitored analyzing the modifications in the relative intensity between the 5D0→7F2 and the 5D0→7F1 transitions. (author)

  6. Separation of 35S-sulfate on neutral aluminium oxide

    International Nuclear Information System (INIS)

    The results of 35S-sulfate chromatography on neutral aluminium oxide (γ-Al2O3) are presented. Possibility of quantitative adsorption of 35S-sulfate on Al2O3 from acidic or neutral potassium chloride solutions of high concentration is shown. Dynamic adsorption capacity of neutral aluminium oxide with respect to sulfate from weakly acidic potassium chloride solution equals near 10 μmol/ml of adsorbent. Optimal parameters for chromatographic isolation of 35S-sulfate without carrier from irradiated KCl target are determined. (author)

  7. Properties of native ultrathin aluminium oxide tunnel barriers

    CERN Document Server

    Gloos, K; Pekola, J P

    2003-01-01

    We have investigated planar metal-insulator-metal tunnel junctions with aluminium oxide as the dielectricum. These oxide barriers were grown on an aluminium electrode in pure oxygen at room temperature till saturation. By applying the Simmons model we derived discrete widths of the tunnelling barrier, separated by DELTA s approx 0.38 nm. This corresponds to the addition of single layers of oxygen atoms. The minimum thickness of s sub 0 approx 0.54 nm is then due to a double layer of oxygen. We found a strong and systematic dependence of the barrier height on the barrier thickness. Breakdown fields up to 5 GV m sup - sup 1 were reached. They decreased strongly with increasing barrier thickness. Electrical breakdown could be described by a metal-insulator like transition of the dielectric barrier due to the large density of tunnelling electrons.

  8. Automotive Aluminium Recycling

    Energy Technology Data Exchange (ETDEWEB)

    Gelas, B. des

    2000-07-01

    This paper aims at providing an overview on the contribution of aluminium recycling in the supply of new aluminium for automotive applications. Based on a presentation on how the global European automotive aluminium supply requirements are met, an analysis of the present and future contribution of automotive aluminium recycling is first presented. Current situation and future developments for automotive aluminium recycling practices are then commented, together with an outline on design principles for easier aluminium recycling. (orig.)

  9. Water defluoridation by aluminium oxide-manganese oxide composite material.

    Science.gov (United States)

    Alemu, Sheta; Mulugeta, Eyobel; Zewge, Feleke; Chandravanshi, Bhagwan Singh

    2014-08-01

    In this study, aluminium oxide-manganese oxide (AOMO) composite material was synthesized, characterized, and tested for fluoride removal in batch experiments. AOMO was prepared from manganese(II) chloride and aluminium hydroxide. The surface area of AOMO was found to be 30.7m2/g and its specific density was determined as 2.78 g/cm3. Detailed investigation of the adsorbent by inductively coupled plasma-optical emission spectrometry, inductively coupled plasma-mass spectrometry, and ion chromatography (for sulphate only) showed that it is composed of Al, Mn, SO4, and Na as major components and Fe, Si, Ca, and Mg as minor components. Thermogravimetric analysis was used to study the thermal behaviour of AOMO. X-ray diffraction analysis showed that the adsorbent is poorly crystalline. The point of zero charge was determined as 9.54. Batch experiments (by varying the proportion of MnO, adsorbent dose, contact time, initial F concentration, and raw water pH) showed that fluoride removal efficiency ofAOMO varied significantly with percentage of MnO with an optimum value of about I11% of manganese oxide in the adsorbent. The optimum dose of the adsorbent was 4 g/L which corresponds to the equilibrium adsorption capacity of 4.8 mg F-/g. Both the removal efficiency and adsorption capacity showed an increasing trend with an increase in initial fluoride concentration of the water. The pH for optimum fluoride removal was found to be in the range between 5 and 7. The adsorption data were analysed using the Freundlich, Langmuir, and Dubinirn-Radushkevich models. The minimum adsorption capacity obtained from the non-linear Freundlich isotherm model was 4.94 mg F-/g and the maximum capacity from the Langmuir isotherm method was 19.2mg F-/g. The experimental data of fluoride adsorption on AOMO fitted well to the Freundlich isotherm model. Kinetic studies showed that the adsorption is well described by a non-linear pseudo-second-order reaction model with an average rate constant of 3

  10. Aluminium in human sweat.

    Science.gov (United States)

    Minshall, Clare; Nadal, Jodie; Exley, Christopher

    2014-01-01

    It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans.

  11. Preparation of Aluminium Oxynitride by Carbothermal Reduction of Aluminium Oxide in a Flowing N2 Atmosphere

    Institute of Scientific and Technical Information of China (English)

    LIYa-wei; YUANRun-zhang; 等

    1996-01-01

    Carbothermal reduction of alumina into aluminium oxynitride(AlON) spinel in a flowing nitrogen atmosphere was studied.The effects of Al2O3/C ratio temperature,soaking time,heating rate molding pressure of samples,and nitrogen flow rate on reactions were investigated.Then the stability of AlON was elucidated and AlON wa confirmed as an intermediate compound in reduction of alumina.

  12. Aluminium structural elements

    OpenAIRE

    Švent, Nejc

    2016-01-01

    This thesis focuses on the structural analysis of aluminium structural members in accordance with the SIST EN 1999-1-1 standard. In the introduction, historical development of aluminium is summarized, as well as the processes of structural aluminium production and manufacture. Predominantly, resistance control checks of aluminium structural members are covered, with special attention to the major contrasts between aluminium and steel structural analyses. Finally, fundamental examples of resis...

  13. Low temperature oxidation of niobium alloy with silicon-aluminium coating

    International Nuclear Information System (INIS)

    Using the gravimetry methods heat resistance of niobium-titanium-aluminium alloy in the air and at 700 deg C in the initial state and when it is protected by silicide-aluminium coatings (with variable content of aluminium) is investigated. Using X-ray diffraction and micro X-ray diffraction analyses, mechanisms of the alloy oxidation and the coating protective effect are studied. The role of aluminium in the formation of coatings is analyzed and according to bend tests the plasticity of the coatings is evaluated

  14. Method of aluminium fluoride manufacture

    International Nuclear Information System (INIS)

    The manufacture of aluminium fluoride is based on waste processing in uranium hexafluoride conversion to uranium oxides within the fuel cycle. The conversion is the stoichiometric conversion of uranium hexafluoride with aluminium nitrate to uranyl nitrate. This is extracted from the water phase by phosphoric acid trialkyl ester to an organic solvent and further processed. The discharge water phase is solidified by evaporation to solid aluminium fluoride and nitric acid. (M.S.)

  15. High Temperature Strength of Oxide Dispersion Strengthened Aluminium

    DEFF Research Database (Denmark)

    Clauer, A.H.; Hansen, Niels

    1984-01-01

    constant (except for the material with the lowest oxide content). The high temperature values of the modulus-corrected yield stresses are approximately two-thirds of the low temperature value. During high temperature creep, there is a definite indication of a threshold stress. This threshold stress......The tensile flow stress of coarse-grained dispersion strengthened Al-Al2O3 materials were measured as a function of temperature (77–873 K) and volume fraction (0.19-0.92 vol.%) of aluminium oxide. For the same material, the creep strength was determined as a function of temperature in the range 573......–873 K. The modulus-corrected yield stress (0.01 offset) is found to be temperature independent at low temperature (195–472 K). Between 473 and 573 K, the yield stress starts to decrease with increasing temperature. At high temperatures (573–873 K), the modulus-corrected yield stress is approximately...

  16. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part I Microstructural investigation

    Science.gov (United States)

    Din, Rameez Ud; Piotrowska, Kamila; Gudla, Visweswara Chakravarthy; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-11-01

    The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3 resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment with solution containing HNO3 caused dissolution of Cu and Si from the intermetallic particles in the aluminium substrate. The growth rate of oxide layer was observed to be a function of MnO4- and NO3- ions present in the aqueous solution. The NO3- ions exhibit higher affinity towards the intermetallic particles resulting in poor coverage by the steam generated oxide layer compared to the coating formed using MnO4- ions. Further, increase in the concentration of NO3- ions in the solution retards precipitation of the steam generated aluminium hydroxide layer.

  17. Characterization of steam generated anti-corrosive oxide films on Aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2014-01-01

    Aluminium and its alloys are widely used in structural and transportation industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further...... of hexavalent chromium is strictly regulated due to its toxic nature and suspected carcinogenicity. So, it is highly imperative to develop other alternatives for chrome conversion coatings. Treatment of aluminium with natural water at elevated temperatures results in the formation of different forms...

  18. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part I Microstructural investigation

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Piotrowska, Kamila; Gudla, Visweswara Chakravarthy;

    2015-01-01

    The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment...

  19. Morphology of Platinum Nanowire Array Electrodeposited Within Anodic Aluminium Oxide Template Characterized by Atomic Force Microscopy

    Institute of Scientific and Technical Information of China (English)

    孔令斌; 陆梅; 李梦轲; 郭新勇; 力虎林

    2003-01-01

    Uniform platinum nanowires were synthesized by electrodepositing the platinum under a very low altering current frequency (20Hz) and increasing voltage (5-15 V) in the pores of anodic aluminium oxide (AAO) template.Atomic force microscopy observation indicates that the template membranes we obtained have hexagonally closepacked nanochannels. The platinum nanowires have highly ordered arrays after partially dissolving the aluminium oxide membrane. With the increasing dissolving time, the platinum nanowire array collapsed. A concave topography of the aluminium substrate was observed after the aluminium oxide membrane was dissolved completely and the platinum nanowires were released from the template. Platinum nanowires were also characterized by transmission electron microscopy and the phase structure of the Al/AAO/Pt composite was proven by x-ray diffraction.

  20. Car-Parrinello Simulation of the Aluminium Oxidation: Questioning the Role of 'Hot Adatoms'

    CERN Document Server

    Schulte, Marius

    2012-01-01

    We present Car-Parrinello molecular dynamics simulations of the initial reaction steps leading to an inert oxide layer on aluminium. The mechanism of the reaction of the aluminium surface with single oxygen molecules is analysed. After adsorption at the surface the oxygen molecules dissociate at a femtosecond timescale and the atoms are chemisorbed at the surface at a distance of several angstrom which falsifies earlier STM results. When the aluminium surface is exposed to higher oxygen pressure, a surface layer essentially consisting of threefold coordinated oxygen atoms starts to form.

  1. ENERGETIC VALORISATION OF SEMI-RIGID AND FLEXIBLE ALUMINIUM PACKAGING BY OXIDATION AT HIGH TEMPERATURE

    OpenAIRE

    López Gómez, Félix Antonio; Román, Carlos P.; García-Díaz, I.; Alguacil, Francisco José; Gómez-Paniagua, M.

    2013-01-01

    This work reports the energy recovered from semi-rigid and flexible aluminium packaging by oxidation at 850ºC in an air atmosphere enriched with 6% oxygen. The physical properties of the different packagings were determined, including their metallic aluminium contents. Their ash contents were determined according to standard ISO 1171:2000. The net calorific value, the required energy, and the calorific gain associated with each, were determined following standards BS EN 13431:2000 and UNE EN...

  2. Sustainable Aluminium Systems

    Directory of Open Access Journals (Sweden)

    Sergio R. Ermolli

    2010-09-01

    Full Text Available In the present paper, an analytical presentation of some popular aluminium systems that contribute to sustainability of structures is presented. Special emphasis has been given to the properties of aluminium, while the influence of these systems in the overall performance of the structure regarding environment and economy is described. In particular, characteristics of aluminium elements such as high reflectivity and recyclability and their role in life cycle analysis (LCA are analyzed. The connections between energy efficiency and conservation of buildings and aluminium application are also discussed. Building applications such as curtain walls, window frames and facade sheets are presented and thoroughly investigated, considering their environmental and economic aspects. Furthermore, many innovative techniques that use aluminium elements in collaboration with other systems in order to produce renewable energy, such as solar panels and photovoltaics, are introduced. Finally, environmental innovations such as optimized ventilation mechanisms and light and shade management systems based on aluminium members are presented.

  3. CNTs tuning and vertical alignment in anodic aluminium oxide membrane

    Institute of Scientific and Technical Information of China (English)

    Maria Sarno; Diana Sannino; Caterina Leone; Paolo Ciambelli

    2012-01-01

    Anodic aluminium oxide (AAOM) membranes were used for template growth of carbon nanotubes (CNT) inside their pores by chemical vapour deposition (CVD) of different hydrocarbons,in the absence of transition metal catalyst.A composite material,containing one nanotube for each channel,having the same length as the membrane thickness and the external diameter close to the diameter of the membrane holes,was obtained.Yield,selectivity,and quality of CNTs in terms of diameter (up to very thin CNT),carbon order,length,arrangement (i.e.number of tubes for each channel),purity,that are critical requisites for several applications were optimized by investigating the effect of changing the hydrocarbon feedstock gas,also in the presence of hydrogen.The samples produced using methane as a feedstock have a well ordered structure.The role of the alumina channels surface during the CNT growth has been investigated and its catalytic activity has been proved for the first time.

  4. Oxidation and waste-to-energy output of aluminium waste packaging during incineration: A laboratory study.

    Science.gov (United States)

    López, Félix A; Román, Carlos Pérez; García-Díaz, Irene; Alguacil, Francisco J

    2015-09-01

    This work reports the oxidation behaviour and waste-to-energy output of different semi-rigid and flexible aluminium packagings when incinerated at 850°C in an air atmosphere enriched with 6% oxygen, in the laboratory setting. The physical properties of the different packagings were determined, including their metallic aluminium contents. The ash contents of their combustion products were determined according to standard BS ISO 1171:2010. The net calorific value, the required energy, and the calorific gain associated with each packaging type were determined following standard BS EN 13431:2004. Packagings with an aluminium lamina thickness of >50μm did not fully oxidise. During incineration, the weight-for-weight waste-to-energy output of the packagings with thick aluminium lamina was lower than that of packagings with thin lamina. The calorific gain depended on the degree of oxidation of the metallic aluminium, but was greater than zero for all the packagings studied. Waste aluminium may therefore be said to act as an energy source in municipal solid waste incineration systems.

  5. A Reaction Coating on Aluminium Alloys by Laser Processing

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1993-01-01

    An aluminium oxide layer of 100 µm in thickness has been successfully coated on aluminium alloy 6061 and pure aluminium using a powder mixture of silicon oxide and aluminium by laser processing. A strong Al/Al2O3 interface was formed. The exothermic chemical reaction between SiO2 and Al may promote

  6. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.;

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

  7. Thermoluminescent response of aluminium oxide thin films subject to gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Arrieta, A.; Escobar A, L.; Camps, E.; Villagran, E.; Gonzalez, P.R

    2006-07-01

    The thermoluminescent (TL) properties of amorphous aluminium oxide thin films (thicknesses as low as 0.3 {mu}m) subjected to gamma (Co-60) irradiation are reported. Aluminium oxide thin films were prepared by laser ablation from an Al{sub 2}O{sub 3} target using a Nd: YAG laser with emission at the fundamental line. The films were exposed to gamma radiation (Co-60) in order to study their TL response. Thermoluminescence glow curves exhibited two peaks at 110 and 176 C. The high temperature peak shows good stability and 30% fading in the first 5 days after irradiation. A linear relationship between absorbed dose and the thermoluminescent response for doses span from 150 mGy to 100 Gy was observed. These results suggest that aluminium oxide thin films are suitable for detection and monitoring of gamma radiation. (Author)

  8. Determination of oxide film thickness on aluminium using 14-MeV neutron activation and BET method

    International Nuclear Information System (INIS)

    A new method is described for the determination of the mean film thickness of aluminium oxides by 14-MeV neutron activation analysis of the oxygen and by BET measurement of the surface area. The mean film thickness obtained is independent of the surface roughness. Stable oxide films consisting of only a few atomic layers of oxygen are detected on aluminium. (author)

  9. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part II corrosion performance

    Science.gov (United States)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-11-01

    Surface treatment of aluminium alloys using steam with oxidative chemistries, namely KMnO4 and HNO3 resulted in accelerated growth of oxide on aluminium alloys. Detailed investigation of the corrosion performance of the treated surfaces was carried out using potentiodynamic polarisation and standard industrial test methods such as acetic acid salt spray (AASS) and filiform corrosion on commercial AA6060 alloy. Barrier properties of the film including adhesion were evaluated using tape test under wet and dry conditions. Electrochemical results showed reduced cathodic and anodic activity, while the protection provided by steam treatment with HNO3 was a function of the concentration of NO3- ions. The coating generated by inclusion of KMnO4 showed highest resistance to filiform corrosion. Overall, the performance of the steam treated surfaces under filiform corrosion and AASS test was a result of the local coverage of the alloy microstructure resulting from steam containing with KMnO4 and HNO3.

  10. Recovery in aluminium

    DEFF Research Database (Denmark)

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

  11. High-speed deposition of protective films of aluminium oxide by the method of reactive magnetron sputtering

    International Nuclear Information System (INIS)

    The high optical characteristics of aluminium films made them attractive for different functional and decorative applications. It is well-known that the corrosion resistance of alloying is determined by the presence of the oxide film on its surface, but on the aluminium films, deposited by vacuum methods, the resistance is extremely low resulting in the relatively rapid failure of the coating. At present, there is a large number of methods of depositing the films of aluminium oxide. In most cases, it is recommended to use reactive magnetron sputtering of an aluminium target in a magnetron spraying system (MSS) using direct current, on dispersion of the target of aluminium oxide in a high-frequency MSS

  12. Aluminium induced oxidative stress results in decreased mitochondrial biogenesis via modulation of PGC-1α expression.

    Science.gov (United States)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Kandimalla, Ramesh J L; Bal, Amanjit; Gill, Kiran Dip

    2013-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the effects of aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of Peroxisome proliferator activated receptor gamma co-activator 1α (PGC-1α) and its downstream targets i.e. Nuclear respiratory factor-1(NRF-1), Nuclear respiratory factor-2(NRF-2) and Mitochondrial transcription factor A (Tfam) in mitochondrial biogenesis. Aluminium lactate (10mg/kgb.wt./day) was administered intragastrically to rats for 12 weeks. After 12 weeks of exposure, we found an increase in ROS levels, mitochondrial DNA oxidation and decrease in citrate synthase activity in the Hippocampus (HC) and Corpus striatum (CS) regions of rat brain. On the other hand, there was a decrease in the mRNA levels of the mitochondrial encoded subunits-NADH dehydrogenase (ND) subunits i.e. ND1, ND2, ND3, Cytochrome b (Cytb), Cytochrome oxidase (COX) subunits i.e. COX1, COX3, ATP synthase (ATPase) subunit 6 along with reduced expression of nuclear encoded subunits COX4, COX5A, COX5B of Electron transport chain (ETC). Besides, a decrease in mitochondrial DNA copy number and mitochondrial content in both regions of rat brain was observed. The PGC-1α was down-regulated in aluminium treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α in aluminium treated rats. Electron microscopy results revealed a significant increase in the mitochondrial swelling, loss of cristae, chromatin condensation and decreases in mitochondrial number in case of aluminium treated rats as compared to control. So, PGC-1α seems to be a potent target for aluminium neurotoxicity, which makes it an almost ideal target to control or limit the damage that has been associated with the defective mitochondrial function seen in neurodegenerative diseases.

  13. Transmittance and Refractive Index of the Lanthanum Strontium Aluminium Tantalum Oxide Crystal

    Institute of Scientific and Technical Information of China (English)

    HU Bo-Qing; WANG Xiao-Ming; ZHOU Tang; ZHAO Zong-Yuan; WU Xing; CHEN Xiao-Long

    2001-01-01

    The lanthanum strontium aluminium tantalum oxide (LSAT) crystal is grown by means of a floating or pulling method. Its optical transmittance, refractive indices in visible and near-infrared areas and its dispersion curve are reported. The transparence range of LSAT is from 0.45 to 4.2μm and its refractive index is 2.0244.

  14. Oxidation effects during laser cladding of aluminium with SiC/Al powders

    NARCIS (Netherlands)

    Hegge, H.J.; Boetje, J.; Hosson, J.Th.M. De

    1990-01-01

    Aluminium substrates were covered with a layer of an Al-SiC powder mixture. The surface was scanned with a laser beam during which the surface was melted. The top layer of the laser tracks contained oxide plates apart from some large SiC particles. In the bottom layer a cellular network was found wi

  15. Aluminium, carbonyls and cytokines in human nipple aspirate fluids: Possible relationship between inflammation, oxidative stress and breast cancer microenvironment.

    Science.gov (United States)

    Mannello, F; Ligi, D; Canale, M

    2013-11-01

    The human breast is likely exposed to Al (aluminium) from many sources including diet and personal care products. Underarm applications of aluminium salt-based antiperspirant provide a possible long-term source of exposure, especially after underarm applications to shaved and abraded skin. Al research in breast fluids likely reflects the intraductal microenvironment. We found increased levels of aluminium in noninvasively collected nipple aspirate fluids (NAF) from 19 breast cancer patients compared with 16 healthy control subjects (268 vs 131 μg/l, respectively; p Aluminium content and carbonyl levels showed a significant positive linear correlation (r(2) 0.6628, p aluminium salts) we also found a significantly increased levels of pro-inflammatory cytokines (IL-1β, IL-6, IL-12 p70, and TNF-α) and chemoattractant CC and CXC chemokines (IL-8, MIP-1α and MCP-1). In 12 invasive cancer NAF samples we found a significant positive linear correlation among aluminium, carbonyls and pro-inflammatory IL-6 cytokine (Y = 64.79x-39.63, r(2) 0.8192, p aluminium ions in oxidative and inflammatory status perturbations of breast cancer microenvironment, suggesting aluminium accumulation in breast microenvironment as a possible risk factor for oxidative/inflammatory phenotype of breast cells.

  16. Aluminium induced oxidative stress results in decreased mitochondrial biogenesis via modulation of PGC-1α expression

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Kandimalla, Ramesh J.L. [Department of Biochemistry, Postgraduate Institute of Medical Education and Research, Chandigarh 160012 (India); Bal, Amanjit [Department of Histopathology, Postgraduate Institute of Medical Education and Research, Chandigarh (India); Gill, Kiran Dip, E-mail: kdgill2002@yahoo.co.in [Department of Biochemistry, Postgraduate Institute of Medical Education and Research, Chandigarh 160012 (India)

    2013-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the effects of aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of Peroxisome proliferator activated receptor gamma co-activator 1α (PGC-1α) and its downstream targets i.e. Nuclear respiratory factor-1(NRF-1), Nuclear respiratory factor-2(NRF-2) and Mitochondrial transcription factor A (Tfam) in mitochondrial biogenesis. Aluminium lactate (10 mg/kg b.wt./day) was administered intragastrically to rats for 12 weeks. After 12 weeks of exposure, we found an increase in ROS levels, mitochondrial DNA oxidation and decrease in citrate synthase activity in the Hippocampus (HC) and Corpus striatum (CS) regions of rat brain. On the other hand, there was a decrease in the mRNA levels of the mitochondrial encoded subunits–NADH dehydrogenase (ND) subunits i.e. ND1, ND2, ND3, Cytochrome b (Cytb), Cytochrome oxidase (COX) subunits i.e. COX1, COX3, ATP synthase (ATPase) subunit 6 along with reduced expression of nuclear encoded subunits COX4, COX5A, COX5B of Electron transport chain (ETC). Besides, a decrease in mitochondrial DNA copy number and mitochondrial content in both regions of rat brain was observed. The PGC-1α was down-regulated in aluminium treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α in aluminium treated rats. Electron microscopy results revealed a significant increase in the mitochondrial swelling, loss of cristae, chromatin condensation and decreases in mitochondrial number in case of aluminium treated rats as compared to control. So, PGC-1α seems to be a potent target for aluminium neurotoxicity, which makes it an almost ideal target to control or limit the damage that has been associated with the defective mitochondrial function seen in neurodegenerative diseases. - Highlights: • Aluminium decreases the mRNA levels of mitochondrial and nuclear encoded

  17. Fatal aluminium phosphide poisoning

    Directory of Open Access Journals (Sweden)

    Meena Mahesh Chand

    2015-06-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

  18. In situ study of the initiation of hydrogen bubbles at the aluminium metal/oxide interface

    Science.gov (United States)

    Xie, De-Gang; Wang, Zhang-Jie; Sun, Jun; Li, Ju; Ma, Evan; Shan, Zhi-Wei

    2015-09-01

    The presence of excess hydrogen at the interface between a metal substrate and a protective oxide can cause blistering and spallation of the scale. However, it remains unclear how nanoscale bubbles manage to reach the critical size in the first place. Here, we perform in situ environmental transmission electron microscopy experiments of the aluminium metal/oxide interface under hydrogen exposure. It is found that once the interface is weakened by hydrogen segregation, surface diffusion of Al atoms initiates the formation of faceted cavities on the metal side, driven by Wulff reconstruction. The morphology and growth rate of these cavities are highly sensitive to the crystallographic orientation of the aluminium substrate. Once the cavities grow to a critical size, the internal gas pressure can become great enough to blister the oxide layer. Our findings have implications for understanding hydrogen damage of interfaces.

  19. TRANSPARENT CONDUCTING OXIDE SYNTHESIS OF ALUMINIUM DOPED ZINC OXIDES BY CHEMICAL COPRECIPITATION

    Directory of Open Access Journals (Sweden)

    Silvia Maioco

    2013-03-01

    Full Text Available Aluminium doped zinc oxides (AZO are promising replacements for tin doped indium oxides (ITO but thin films show a wide range of physical properties strongly dependent on deposition process conditions. Submicrometric 1% aluminum doped zinc oxide ceramics (AZO are examined, prepared by coprecipitation, from Zn(NO32 and Al(NO33 aqueous solutions, sintered at 1200°C and subsequently annealed in 10-16 atm controlled oxygen fugacity atmospheres, at 1000°C. Electrical resistivity diminishes by two orders of magnitude after two hours of annealing and the Seebeck coefficient gradually changes from -140 to -50 µV/K within 8 h. It is concluded that increased mobility is dominant over the increased carrier density, induced by changes in metal-oxygen stoichiometry

  20. Porosity Study of Hybrid Silica Mesostructure in Aluminium Oxide Membrane Columnar by Cyclic Voltammetry Method

    Directory of Open Access Journals (Sweden)

    M.N. Jalil

    2011-12-01

    Full Text Available Silica mesostructure has been grown within with a porous aluminium oxide membrane columnar material (hybrid-AOM. This was prepared using a sol-gel technique with Pluronic P123 triblock copolymer as the structure-directing agent and tetraethyl orthosilicate as the inorganic source. The porosity of the hybrid-AOM after ethanol extraction was calculated from the cyclic voltammetry response of a neutral probe (FcMeOH, using Randles-Sevčik equation.

  1. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.H.H.; Soetens, F.

    2006-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical pr

  2. Evaluation of the mechanical properties of microarc oxidation coatings and 2024 aluminium alloy substrate

    CERN Document Server

    Xue Wen Bin; Deng Zhi Wei; Chen Ru Yi; Li Yong Liang; Zhang Ton Ghe

    2002-01-01

    A determination of the phase constituents of ceramic coatings produced on Al-Cu-Mg alloy by microarc discharge in alkaline solution was performed using x-ray diffraction. The profiles of the hardness, H, and elastic modulus, E, across the ceramic coating were determined by means of nanoindentation. In addition, a study of the influence of microarc oxidation coatings on the tensile properties of the aluminium alloy was also carried out. The results show that the H-and E-profiles are similar, and both of them exhibit a maximum value at the same depth of coating. The distribution of the alpha-Al sub 2 O sub 3 phase content determines the H- and E-profiles of the coatings. The tensile properties of 2024 aluminium alloy show less change after the alloy has undergone microarc discharge surface treatment.

  3. Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium-doped zinc oxide nanorods

    Indian Academy of Sciences (India)

    Kanchan Saxena; Amit Kumar; Nishant Malik; Pramod Kumar; V K Jain

    2014-04-01

    Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol. Current–voltage characteristics have been investigated in dark and under UV-light illumination. Aluminium doping in ZnO increase its electrical conductivity and further polyvinyl alcohol coating on Al-doped ZnO increase UV sensitivity of the material. Response and recovery time of Al-doped ZnO and PVA-coated Al-doped ZnO nanorods have been recorded. PVA-coated Al-doped ZnO nanorods shows very fast response and recovery time of 10 s in comparison to uncoated ZnO (20 min) nanorods.

  4. Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

    Science.gov (United States)

    Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

    2016-02-01

    Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

  5. Steam generated conversion coating on aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    and growth of oxide film on different intermetallic particles and corrosion behaviour of such alloys.Surface morphology was observed by using FEG-SEM, EDX and FIB-SEM. Metal oxide surface characterization and compositional depth profiling were investigated by using XPS and GD-OES respectively......Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed......) depending on the preparation parameters/conditions. Moreover, with the knowledge of factors controlling film growth, composition and morphology, such oxide layers carry huge potential for practical applications. Pure aluminium (AA1090, 99.94 wt. %) and other aluminium alloy surfaces were exposed to high...

  6. Advances in development and application of aluminium batteries

    DEFF Research Database (Denmark)

    Qingfeng, Li; Zhuxian, Qiu

    2001-01-01

    Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation o...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

  7. Aluminium as heating fuel. Tests with aluminium powder prove suitability in principle. Aluminium als Heizungs-Brennstoff. Versuche mit Aluminiumpulver beweisen prinzipielle Eignung

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R.

    1990-12-01

    Tests prove that aluminium powder is perfectly suited as fuel and storage material for solar energy. The combustion product itself is again the base material for aluminium production, i.e. aluminium can be recycled. There are three problematic areas: 1. flame stability, 2. combustion duration and 3. environmental compatibility. Further development projects will aim at the construction of practice-orientated plants in which combustion, heat extraction and recovery of aluminium oxide is combined. A further aim is the melting burner to which aluminium is supplied in form of wires, cuttings or rods. (BWI).

  8. Recovery in aluminium

    OpenAIRE

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X-ray diffraction technique for studies of the evolution of grains within polycrystalline materials. The much smaller volume of the crystallites of interest here in comparison to grains implies that the ...

  9. Aluminium and human breast diseases.

    Science.gov (United States)

    Darbre, P D; Pugazhendhi, D; Mannello, F

    2011-11-01

    The human breast is exposed to aluminium from many sources including diet and personal care products, but dermal application of aluminium-based antiperspirant salts provides a local long-term source of exposure. Recent measurements have shown that aluminium is present in both tissue and fat of the human breast but at levels which vary both between breasts and between tissue samples from the same breast. We have recently found increased levels of aluminium in noninvasively collected nipple aspirate fluids taken from breast cancer patients (mean 268 ± 28 μg/l) compared with control healthy subjects (mean 131 ± 10 μg/l) providing evidence of raised aluminium levels in the breast microenvironment when cancer is present. The measurement of higher levels of aluminium in type I human breast cyst fluids (median 150 μg/l) compared with human serum (median 6 μg/l) or human milk (median 25 μg/l) warrants further investigation into any possible role of aluminium in development of this benign breast disease. Emerging evidence for aluminium in several breast structures now requires biomarkers of aluminium action in order to ascertain whether the presence of aluminium has any biological impact. To this end, we report raised levels of proteins that modulate iron homeostasis (ferritin, transferrin) in parallel with raised aluminium in nipple aspirate fluids in vivo, and we report overexpression of mRNA for several S100 calcium binding proteins following long-term exposure of MCF-7 human breast cancer cells in vitro to aluminium chlorhydrate. PMID:22099158

  10. Laser welding of aluminium alloys

    OpenAIRE

    Forsman, Tomas

    2000-01-01

    This thesis treats laser welding of aluminium alloys from a practical perspective with elements of mathematical analysis. The theoretical work has in all cases been verified experimentally. The aluminium alloys studied are from the 5xxx and 6xxx groups which are common for example in the automotive industry. Aluminium has many unique physical properties. The properties which more than others have been shown to influence the welding process is its high reflection, high thermal conductivity, lo...

  11. Development of a new aluminium matrix composite reinforced with iron oxide (Fe3O4

    Directory of Open Access Journals (Sweden)

    E. Bayraktar

    2010-01-01

    Full Text Available Purpose: of this paper is to develop new aluminium matrix (intermetallic composites reinforced with iron oxide (Fe3O4 that will be used in aeronautical engineering or in electronic industry. Different parameters such as sintering time and temperature, reinforcement, compact pressure were evaluated. The final purpose of this project is going on to improve conductivity and magnetic permeability of this new composite.Design/methodology/approach: In this paper, a new alternative materials “aluminium–iron oxide (Fe3O4, naturally as the mineral magnetite powder composite” has been developed by using a microwave (in the laboratory scale sintering programme with various aspect ratios, that iron oxide (Fe3O4 particle sizes and aluminium powders together were prepared. This paper contains partially preliminary results of our going-on research project.Findings: Green density increased regularly depending on the compact pressure and percentage of the iron oxide (Fe3O4. Micro and macro porosity was not found due to very clean microwave sintering. Density after microwave sintering was higher than that of traditional sintering in an electrical oven.Research limitations/implications: This project is going on and magnetic permeability and conductivity of this composite will be improved.Practical implications: This composite is new and clean and thanks to the new microwave sintering basically will be used in aeronautical engineering. Microwave heating results in lower energy costs and decreased processing times for many industrial processes.Originality/value: Originality of this paper is to use a new reinforcement in the aluminium matrix composite; Fe3O4-iron oxide. A new method - microwave sintering- has been carried out on this composite.

  12. EFFECTS OF HOUSING SYSTEMS ON PRODUCTIVE PERFORMANCE OF COMMERCIAL LAYERS FOLLOWING INDUCED MOLTING BY ALUMINIUM OXIDE SUPPLEMENTATION

    Directory of Open Access Journals (Sweden)

    M. YOUSAF AND N. AHMAD1

    2006-07-01

    Full Text Available The project was carried out to compare the performance of molted layers by aluminium oxide supplementation in cages and on litter floor system. Seventy two Single Comb White Leghorn commercial layers (60 weeks old were divided into six experimental units of 12 layers each. These experimental units were randomly divided into two groups, each consisting of three experimental units, one group was reared on litter floor and the other in cages. The layers were provided with 35 gm feed containing 4 gm aluminium oxide/kg of feed for first 14 days of molting period (66-67 weeks of age. The layers showed significant reduction in body weight following induced molting by aluminium oxide under both housing systems. Body weight loss was higher, while feed consumption was lower, in the cages as compared to litter floor system. The layers molted by aluminium oxide showed significantly higher egg production in the cages (P≤0.05 than in litter floor system (P≤0.05. The layers in the subsequent production cycle showed improvement in egg weight, egg shell thickness and Haugh Unit Score. The egg weight and egg shell thickness were higher in the birds kept on litter floor system than those kept in cages (P≥0.05. However, Haugh unit score was higher in the cage system. It was concluded that aluminium oxide can be effectively supplemented for better production performance and improved egg quality in the second production cycle preferably in the cages.

  13. Development and characterization of ultra-thin dosemeters of aluminium oxide

    International Nuclear Information System (INIS)

    The aim of the present thesis work has been to investigate the thermoluminescent (Tl) response of aluminium oxide thin films with thicknesses of the order of 300 nm prepared by laser ablation. Aluminium oxide thin films show Tl response after they are subject to ultraviolet, beta and gamma radiation. The Tl curves exhibit peaks around 75 C and 169 C for UV radiation, 112 C and 180 C for beta particles and 110 C and 176 C for gamma radiation. In order to improve the Tl response some growth parameters such as power density and distance target-substrate were varied. The relation dose-response shows a non-linear behavior for UV irradiation; a linear behavior for beta-particles dose from 150 mGy to 50 Gy, and a linear behavior for gamma radiation dose from 5 Gy to 100 Gy. The kinetic Tl parameters were determined by Computerized Glow Curve Deconvolution (CGCD) method as well as using analytical methods. The CGCD results show that the high temperature peak is composed by four peaks with maximums in 165.7, 188.1, 215.3, 246.5 C. These obey a second order kinetics. The trap depth (E) values are 1.4, 1.6, 1.8 and 2.0 eV respectively. The different analytical results show a trap depth values of 0.914, 0.82 and 0.656 eV respectively. Oxide aluminium thin films obtained would be a suitable tool owing to their potential applications in clinical dosimetry, in the dose distributions due to weekly penetrating radiation determination, and in interfaces dosimetry. (Author)

  14. First Principles Study of Aluminium Vacancy in Wurtzite Aluminium Nitride

    Institute of Scientific and Technical Information of China (English)

    GAO Ting-Ge; YI Jue-Min; ZHOU Zi-Yao; HU Xiao-Dong

    2008-01-01

    @@ We report that the aluminium vacancy in wurtzite AIN brings about two impurity levels e and a2 in the band gap, not just one single t2 level The aluminium vacancy carries a magnetic moment of 1 μB in the ground state. The molecule orbit of the aluminium vacancy becomes e↑↑ a2↑ rather than e↑↑ a2↑. The calculation is carried out by using the CASTEP code. The intrinsic symmetry of wurtzite A1N is the driving force for this spin splitting. Finally the symmetry of wurtzite AlN results in an anti-ferromagnetic coupling between the aluminium vacancies, as is predicted. Our findings are helpful to gain a more through understanding of the structural and spin property of aluminium vacancy in wurtzite AIN.

  15. Mechanical and Abrasive Wear Properties of Anodic Oxide Layers Formed on Aluminium

    Institute of Scientific and Technical Information of China (English)

    W.Bensalah; K.Elleuch; M.Feki; M.Wery; H.F.Ayedi

    2009-01-01

    Aluminium oxide coatings were formed on aluminium substrates in oxalic acid-sulphuric acid bath. Abrasion tests of the obtained anodic layers were carried out on a pin-on-disc machine in accordance with the ISO/DP 825 specifications. The Vickers microhardness, D (HV0.2). and the abrasion weight loss, Wa (mg) were measured. Influence of oxalic acid concentration (Cox), bath temperature (T) and anodic current density (J) on D and Wa has been examined, and the sulphuric acid concentration (Caul) was maintained at 160 g.L-1. It was found that high microhardness and abrasive wear resistance of oxide layers were produced under low temperatures and high current densities with the addition of oxalic acid. The morphology and the composition of the anodic oxide layer were examined by scanning electron microscopy (SEM), atomic force microscopy (AFM), optical microscopy and glow-discharge optical emission spectroscopy (GDOES). It was found that the chemistry of the anodizing electrolyte, temperature, and current density are the controlling factors of the mechanical properties of the anodic oxide layer.

  16. Chemical composition and morphology of oxidic ceramics at filtration of steel deoxidised by aluminium

    Directory of Open Access Journals (Sweden)

    J. Bažan

    2009-10-01

    Full Text Available Composition and morphology of filter ceramics were investigated during filtration of steel deoxidised by aluminium. Filtration was realized with use of filters based on oxidic ceramics Cr2O3, TiO2, SiO2, ZrO2, Al2O3, 3Al2O3•2SiO2 and MgO•Al2O3. It was established that change of interphase (coating occurs during filtration of steel on the surface of capillaries of ceramics, where content of basic oxidic component decreases. Loss of oxidic component in the coating is replaced by increase of oxides of manganese and iron and it is great extent inversely proportional to the value of Gibbs’ energy of oxide, which forms this initial basis of ceramics.

  17. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2005-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge load

  18. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge load

  19. Nuclear analysis of a rare earth containing protective oxide on aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Gorman, J.D.; Paterson, P.J.K. [Royal Melbourne Inst. of Tech., VIC (Australia); Hughes, A.E. [Commonwealth Scientific and Industrial Research Organisation (CSIRO), Melbourne, VIC (Australia). Div. of Materials Science

    1996-12-31

    The aim is study was to examine the thickness of the conversion coating as well as the elemental depth distribution of cerium and molybdenum using Rutherford Backscattering Spectroscopy (RBS), Scanning Electron Microscopy (SEM), Scanning Auger Electron Spectroscopy and Forward Recoil Spectroscopy (FRS). In addition, RBS has been used to examine how changes in processing conditions, particularly the treatment temperatures, influences the coating thickness and Ce distribution at each process step. SEM established that a crazed oxide structure was developed over the matrix of the alloy using the above process steps. RBS was chosen to provide elemental concentration versus depth information on these samples since it is largely insensitive to surface topography when the detector is set to high scattering angles. A other advantage of using RBS for this particular system is that the heavy elements incorporated into the coating such as Ce and Mo because of their high atomic number compared to the aluminium oxide, are well separated from aluminium and oxygen at their higher recoil energies. Forward Recoil Spectroscopy is capable of detecting hydrogen and it has been used to confirm that the coating is hydrated and to establish the hydrogen distribution within the final oxide coating on each alloy. 7 refs., 1 tab., 4 figs.

  20. Thermal Conductivity Measurement of Submicron-Thick Aluminium Oxide Thin Films by a Transient Thermo-Reflectance Technique

    Institute of Scientific and Technical Information of China (English)

    BAI Su-Yuan; TANG Zhen-An; HUANG Zheng-Xing; YU Jun; WANG Jia-Qi

    2008-01-01

    Thermal conductivity of submicron-thick aluminium oxide thin films prepared by middle frequency magnetron sputtering is measured using a transient thermo-reflectance technique.A three-layer model based on transmission line theory and the gentic algorithm optimization method are employed to obtain the thermal conductivity of thin films and the interfacial thermal resistance.The results show that the average thermal conductivity of 3301000nm aluminium oxide thin films is 3.3Wm-1 K-1 at room temperature.No significant thickness dependence is found.The uncertainty of the measurement is less than 10%.

  1. Surface oxide formation during corona discharge treatment of AA 1050 aluminium surfaces

    DEFF Research Database (Denmark)

    Minzari, Daniel; Møller, Per; Kingshott, Peter;

    2008-01-01

    Atmospheric plasmas have traditionally been used as a non-chemical etching process for polymers, but the characteristics of these plasmas could very well be exploited for metals for purposes more than surface cleaning that is presently employed. This paper focuses on how the corona discharge...... process modifies aluminium AA 1050 surface, the oxide growth and resulting corrosion properties. The corona treatment is carried out in atmospheric air. Treated surfaces are characterized using XPS, SEM/EDS, and FIB-FESEM and results suggest that an oxide layer is grown, consisting of mixture of oxide...... and hydroxide. The thickness of the oxide layer extends to 150–300 nm after prolonged treatment. Potentiodynamic polarization experiments show that the corona treatment reduces anodic reactivity of the surface significantly and a moderate reduction of the cathodic reactivity....

  2. Deposition of Aluminium Oxide Films by Pulsed Reactive Sputtering

    Institute of Scientific and Technical Information of China (English)

    Xinhui MAO; Bingchu CAI; Maosong WU; Guoping CHEN

    2003-01-01

    Pulsed reactive sputtering is a novel process used to deposit some compound films, which are not deposited by traditional D.C. reactive sputtering easily. In this paper some experimental results about the deposition of Al oxide films by pulsed reactive sputtering are presented. The hysteresis phenomenon of the sputtering voltage and deposition rate with the change of oxygen flow during sputtering process are discussed.

  3. Cavitation erosion resistance of microarc oxidation coating on aluminium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Feng [School of Mechanical Engineering, Southeast University, Nanjing, 211189 (China); Jiang, Shuyun, E-mail: jiangshy@seu.edu.cn [School of Mechanical Engineering, Southeast University, Nanjing, 211189 (China); Liang, Jun [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, 730000 (China)

    2013-09-01

    Two ceramic coatings are prepared on 2124 aluminum alloy by microarc oxidation (MAO) technology. To explore the cavitation erosion resistance of the MAO coating, cavitation tests were performed by using a rotating-disk test rig. The mass losses, surface morphologies, chemical compositions and the phase constituents of the samples after cavitation tests were examined by using digital balance, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The results indicate that the MAO coatings can extend the incubation period of aluminum alloy, and thus enhance the cavitation erosion resistance as compared to the untreated aluminum alloy samples. After duration of 63 h cavitation test, a lot of erosion pits and the particles in various shapes can be observed on the surfaces of the aluminum alloy samples, while only a few erosion pits are observed on the MAO coatings. Moreover, the mean depths of erosion on the MAO coatings are lower in the first 30 h and are independent on erosion time. The results show that the cavitation erosion of MAO coating is governed by water mechanical impaction, resulting from the effects of brittle fracture of the MAO coating.

  4. Roll bonding of strained aluminium

    DEFF Research Database (Denmark)

    Staun, Jakob M.

    2003-01-01

    This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right circumsta......This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... circumstances both materials show good bonding, but the high purity material is excluded because of recrystallisation and the resulting loss of mechanical properties. The effect of cross stacking and roll bonding pre-strained sheets of the commercial purity material is investigated and some dependence...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

  5. Aluminium, antiperspirants and breast cancer.

    Science.gov (United States)

    Darbre, P D

    2005-09-01

    Aluminium salts are used as the active antiperspirant agent in underarm cosmetics, but the effects of widespread, long term and increasing use remain unknown, especially in relation to the breast, which is a local area of application. Clinical studies showing a disproportionately high incidence of breast cancer in the upper outer quadrant of the breast together with reports of genomic instability in outer quadrants of the breast provide supporting evidence for a role for locally applied cosmetic chemicals in the development of breast cancer. Aluminium is known to have a genotoxic profile, capable of causing both DNA alterations and epigenetic effects, and this would be consistent with a potential role in breast cancer if such effects occurred in breast cells. Oestrogen is a well established influence in breast cancer and its action, dependent on intracellular receptors which function as ligand-activated zinc finger transcription factors, suggests one possible point of interference from aluminium. Results reported here demonstrate that aluminium in the form of aluminium chloride or aluminium chlorhydrate can interfere with the function of oestrogen receptors of MCF7 human breast cancer cells both in terms of ligand binding and in terms of oestrogen-regulated reporter gene expression. This adds aluminium to the increasing list of metals capable of interfering with oestrogen action and termed metalloestrogens. Further studies are now needed to identify the molecular basis of this action, the longer term effects of aluminium exposure and whether aluminium can cause aberrations to other signalling pathways in breast cells. Given the wide exposure of the human population to antiperspirants, it will be important to establish dermal absorption in the local area of the breast and whether long term low level absorption could play a role in the increasing incidence of breast cancer. PMID:16045991

  6. Ongoing characterization of passivated aluminium nanopowders

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, Q.S.M.; Fouchard, R.C.; Turcotte, A-M.; Abdel-Qader, Z.; Jones, D.E.G. [Natural Resources Canada, CANMET, Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2002-04-01

    For characterization, the thermal behaviour of two aluminium nanopowders - Alss and Alssef - in air was determined using differential scanning calorimetry (DSC), simultaneous thermogravimetry-DTA (TG-DTA) and accelerating rate calorimetry (ARC). Alss and Alssef were found to be less reactive to air than previously determined for Als And Alex, possibly due to their thicker and different type of passivating layer. Stability determination for Alss and Alssef in a wet oxidizing environment was carried out using ARC, whereas outgassing behaviour of mixtures of ammonium dinitramide (ADN) and the various aluminium powders was investigated using TG-DTA-FTIR-MS (Fourier Transform Infrared Spectrometry-Mass Spectrometry). The addition of various aluminium powders resulted in only minimal effect on the thermal stability of ADN. Electrostatic discharge, friction sensitivities of ADN and its mixtures with various aluminium powders, and thermal stability and sensitivity of mixtures of nano-sized molybdenum trioxide with aluminium nanopowders were also studied. The electrostatic discharge sensitivity of molybdenum trioxide was shown to increase by the addition of aluminium nanopowders. 23 refs., 5 tabs., 7 figs.

  7. Aluminium oxide ultrathin-film growth on the Mo(110) surface: a work-function study

    Energy Technology Data Exchange (ETDEWEB)

    Magkoev, T.T. [Department of Physics, State University of North Ossetia, Vladikavkaz (Russian Federation)]. E-mail: magkoev@osetia.ru; Vladimirov, G.G. [Department of Physics, St. Petersburg State University, St. Petersburg (Russian Federation)

    2001-07-16

    Submonolayer-to-multilayer films deposited onto the surface of Mo(110) crystal by thermal evaporation of bulk aluminium oxide in ultrahigh vacuum have been studied by Auger electron spectroscopy, low-energy electron diffraction and work-function measurements (the Anderson method). The Auger spectra of the films at all coverages studied are composed of the lines characteristic for the bulk oxide; no evidence of a metallic Al signal is found. The layer-by-layer growth mode occurs up to two monolayers. Increase of the reflectivity of the low-energy electrons (1 to 4 eV) as the film grows indicates that the film has a reduced density of states, which probably resembles the band gap of the bulk alumina. The films deposited on a substrate held at room temperature are amorphous, whereas deposition at 1300 K results in a hexagonal superstructure. (author). Letter-to-the-editor.

  8. Titanium oxide layers on aluminium substrates produced by the anodic spark deposition process

    International Nuclear Information System (INIS)

    Titanium oxide layers were prepared on pure aluminium substrates by the anodic spark deposition method. The formed crystalline titania (TiO2) phases rutile and anatase and the sodium titanium oxide (Na0.23TiO2) were identified. The corresponding crystallite size values were obtained from X-ray diffraction data by means of the Rietveld method. The crystallite size of each of these phases continuously increases with rising current density. Furthermore, the two-dimensional distribution of the titania phases on the sample surface was determined by Raman spectroscopy. It was found that the rutile/anatase ratio is inhomogeneous distributed on an observed area of 400 x 400 μm2.

  9. The toxicity of aluminium in humans.

    Science.gov (United States)

    Exley, C

    2016-06-01

    We are living in the 'aluminium age'. Human exposure to aluminium is inevitable and, perhaps, inestimable. Aluminium's free metal cation, Alaq(3+), is highly biologically reactive and biologically available aluminium is non-essential and essentially toxic. Biologically reactive aluminium is present throughout the human body and while, rarely, it can be acutely toxic, much less is understood about chronic aluminium intoxication. Herein the question is asked as to how to diagnose aluminium toxicity in an individual. While there are as yet, no unequivocal answers to this problem, there are procedures to follow to ascertain the nature of human exposure to aluminium. It is also important to recognise critical factors in exposure regimes and specifically that not all forms of aluminium are toxicologically equivalent and not all routes of exposure are equivalent in their delivery of aluminium to target sites. To ascertain if Alzheimer's disease is a symptom of chronic aluminium intoxication over decades or breast cancer is aggravated by the topical application of an aluminium salt or if autism could result from an immune cascade initiated by an aluminium adjuvant requires that each of these is considered independently and in the light of the most up to date scientific evidence. The aluminium age has taught us that there are no inevitabilities where chronic aluminium toxicity is concerned though there are clear possibilities and these require proving or discounting but not simply ignored. PMID:26922890

  10. Positive Biomechanical Effects of Titanium Oxide for Sandblasting Implant Surface as an Alternative to Aluminium Oxide.

    Science.gov (United States)

    Gehrke, Sergio Alexandre; Taschieri, Silvio; Del Fabbro, Massimo; Coelho, Paulo Guilherme

    2015-10-01

    The aim of this study was to evaluate the physico-chemical properties and the in vivo host response of a surface sandblasted with particles of titanium oxide (TiO2) followed by acid etching as an alternative to aluminium oxide. Thirty titanium disks manufactured in the same conditions as the implants and 24 conventional cylindrical implants were used. Half of the implants had a machined surface (Gcon) while in the other half; the surface was treated with particles of TiO2 followed by acid etching (Gexp). Surface characterization was assessed by scanning electron microscope (SEM), energy dispersive X-ray spectrometry (EDS), profilometry, and wettability. For the in vivo test, 12 implants of each group were implanted in the tibia of 6 rabbits, and were reverse torque tested after periods of 30 or 60 days after implantation. Following torque, SEM was utilized to assess residual bone-implant contact. The surface characterization by SEM showed a very homogeneous surface with uniform irregularities for Gexp and a small amount of residues of the blasting procedure, while Gcon presented a surface with minimal irregularities from the machining tools. Wettability test showed decreased contact angle for the Gcon relative to the Gexp. The Gexp removal torque at 30 and 60 days was 28.7%, and 33.2% higher relative to the Gcon, respectively. Blasting the surface with particles of TiO2 represents an adequate option for the surface treatment of dental implants, with minimal risk of contamination by the residual debris from the blasting procedure. PMID:24001048

  11. On adsorption of aluminium and methyl groups on silica for TMA/H2O process in atomic layer deposition of aluminium oxide nano layers

    Indian Academy of Sciences (India)

    Anu Philip; K Rajeev Kumar

    2010-04-01

    A detailed chemisorption mechanism is proposed for the atomic layer deposition (ALD) of aluminium oxide nano layers using trimethyl aluminum (TMA) and water as precursors. Six possible chemisorption mechanisms, complete ligand exchange, partial ligand exchange, simple dissociation, complete dissociation via ligand exchange, complete dissociation and association, are proposed and related parameters like ligand to metal ratio (L/M), concentrations of metal atoms and methyl groups adsorbed are calculated and compared against reported values. The maximum number of methyl groups that can get attached on the surface is calculated in a different way which yields a more realistic value of 6.25 per nm2 substrate area. The dependence of the number of metal atoms adsorbed on OH concentration is explained clearly. It is proposed that a combination of complete ligand exchange and complete dissociation is the most probable chemisorption mechanism taking place at various OH concentrations.

  12. Friction surfacing of aluminium alloys

    OpenAIRE

    Pereira, Diogo Jorge O. A.

    2012-01-01

    Friction surfacing is a solid state joining process that has attracted much interest in the past decades. This technology allows joining dissimilar metallic materials while avoiding the brittle intermetallic formations, involving temperatures bellow melting point and producing like forged metal structures. Much research using different steels has been made but the same does not happen with aluminium alloys, specially using different aluminium alloys. Friction surface coatings using cons...

  13. Investigation of structural, morphological, luminescent and thermal properties of combusted aluminium-based iron oxide

    Science.gov (United States)

    Shinde, S. S.; Rajpure, K. Y.

    2010-12-01

    Nanocomposites of aluminium integrated hematite α-Fe 2O 3 are synthesized by combustion route using aqueous solutions of AR grade ferric trichloride and aluminium nitrate as precursors. The influence of aluminium incorporation on to the morphology, XPS, photoluminescence and thermal properties has been investigated. The FESEM and AFM micrographs depict that the samples are compact and have homogeneously distributed grains of varying sizes (˜20-60 nm). Chemical composition and valence states of constituent elements in hematite are analyzed by XPS. In room temperature photoluminescence (PL) study, we observed strong violet emission around 436 nm without any deep-level emission and a small PL FWHM indicating that the concentrations of defects are responsible for deep-level emissions. The specific heat and thermal conductivity study shows the phonon conduction behavior is dominant. We studied interparticle interactions using complex impedance spectroscopy. We report a new potential candidate for its possible applications in optoelectronics and magnetic devices.

  14. Gas-Phase Deposition of Ultrathin Aluminium Oxide Films on Nanoparticles at Ambient Conditions

    Directory of Open Access Journals (Sweden)

    David Valdesueiro

    2015-03-01

    Full Text Available We have deposited aluminium oxide films by atomic layer deposition on titanium oxide nanoparticles in a fluidized bed reactor at 27 ± 3 °C and atmospheric pressure. Working at room temperature allows coating heat-sensitive materials, while working at atmospheric pressure would simplify the scale-up of this process. We performed 4, 7 and 15 cycles by dosing a predefined amount of precursors, i.e., trimethyl aluminium and water. We obtained a growth per cycle of 0.14–0.15 nm determined by transmission electron microscopy (TEM, similar to atomic layer deposition (ALD experiments at a few millibars and ~180 °C. We also increased the amount of precursors dosed by a factor of 2, 4 and 6 compared to the base case, maintaining the same purging time. The growth per cycle (GPC increased, although not linearly, with the dosing time. In addition, we performed an experiment at 170 °C and 1 bar using the dosing times increased by factor 6, and obtained a growth per cycle of 0.16 nm. These results were verified with elemental analysis, which showed a good agreement with the results from TEM pictures. Thermal gravimetric analysis (TGA showed a negligible amount of unreacted molecules inside the alumina films. Overall, the dosage of the precursors is crucial to control precisely the growth of the alumina films at atmospheric pressure and room temperature. Dosing excess of precursor provokes a chemical vapour deposition type of growth due to the physisorption of molecules on the particles, but this can be avoided by working at high temperatures.

  15. Wearing tests on aluminium coated with diamond by triboadhesion

    Institute of Scientific and Technical Information of China (English)

    J.M.RodríguezLelis; B.D.Angulo; J.O.Colín; J.PorcayoCalderón

    2001-01-01

    In this work the results obtained from subjecting aluminium coated with diamond by tri-boadhesion to a wearing process with a plane rider. Here it is shown the ratio of the normal toshearing forces, called friction factor, as an indication of the resistance of the surface. It was foundthat the film of the aluminium coated with diamond resisted three times compared with the oxida-tion film of commercial aluminium, which for the purpose of this work was considered withoutcoating.

  16. Application of INAA for investigation of magnesium and aluminium oxide materials

    International Nuclear Information System (INIS)

    The paper presents investigations of changes in optical absorption and photo luminescence spectra of magnesium oxide, and natural and synthetic magnesium aluminium spinel related with the content of transition metal ions (Cr, Fe, Mn) and the irradiation with fast neutrons. Six synthetic single magnesium aluminium spinel crystals with different stoichiometry (MgO·nAl2O3), five natural crystals from Ural and Pamir deposits, and seven MgO crystals were studied. Micro impurities (Cr, Fe, and Mn) and macro component (Mg, Al) quantities have been determined using the instrumental neutron activation analysis technique. Concentrations of impurities in different spinels were found in following ranges: for Cr-1 × 10-4 to 8 × 10-2 %, for Mn-2 × 10-5 to 23 %, for Fe-1 × 10-4 to 1.2 %. Three ranges of luminescence: 380-460, 650-850 and 850-1,050 nm, were established in the most part of the investigated MgO samples. Analysis shows that the intensity of emission in each of these regions is strongly dependent on the concentration of transition metal ions. Great deviation from the stoichiometry of the irradiated MgO·2.8Al2O3 crystal leads to the local structure of α-Al2O3 formation around Cr3+ ions. The orange emission is attributed to Mn2+ in octahedral coordination, it can be assumed that the band at 570 nm is belonging to the complex centre 'Mn2+-F+ (or F centre)'. (author)

  17. Accelerated growth of oxide film on aluminium alloys under steam: Part I: Effects of alloy chemistry and steam vapour pressure on microstructure

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Gudla, Visweswara C.; Jellesen, Morten S.;

    2015-01-01

    at the top. The kinetics of formation of film understeamwas rapid; approx. 350nm thick layers were generated within 5 s of steam treatment, however increase in thickness of the oxide retarded further growth. The enrichment or depletion of different alloying elements at the surface of aluminium as a result...... of alkaline etching pre-treatment influenced the thickness and growth of theoxide. Moreover the steam treatment resulted in the partial oxidation of second phase intermetallic particles present in the aluminium alloy microstructure....

  18. Preparation of aluminium lakes by electrocoagulation

    OpenAIRE

    Prapai Pradabkham

    2008-01-01

    Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  19. Effect of hydrogen on aluminium and aluminium alloys: A review

    DEFF Research Database (Denmark)

    Ambat, Rajan; Dwarakadasa, E.S.

    1996-01-01

    Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

  20. Spectroscopic study of plasma during electrolytic oxidation of magnesium-aluminium alloys

    Science.gov (United States)

    Jovović, J.

    2014-12-01

    Plasma during Electrolytic Oxidation (PEO) of magnesium-aluminium alloys is studied in this work by means of Optical Emission Spectroscopy (OES). Spectral line shapes of the Hβ, Al II 704.21 nm and Mg II 448.11 nm line are analyzed to measure plasma electron number density Ne. From the Hβ line profile, two PEO processes characterized by relatively low electron number densities Ne ≈ 1015 cm-3 and Ne ≈ 2 × 1016 cm-3 were discovered while the shape and shift of Al II and Mg II lines revealed the third process characterized by large electron density Ne = (1-2) × 1017 cm-3. Low Ne processes, related with breakdown in gas bubbles and on oxide surface, are not influenced by anode material or electrolyte composition. The ejection of evaporated anode material through oxide layer is designated here as third PEO process. Using the Boltzmann plot technique, electron temperature of 4000 K and 33000 K is determined from relative intensities of Mg I and O II lines, respectively. Several difficulties in the analysis of spectral line shapes are met during this study and the ways to overcome some of the obstacles are demonstrated.

  1. Modelling of liquid metal flow and oxide film defects in filling of aluminium alloy castings

    Science.gov (United States)

    Dai, X.; Jolly, M.; Yang, X.; Campbell, J.

    2012-07-01

    The liquid metal flow behaviours in different runner system designs have important effects on the mechanical strength of aluminium alloy castings. In this paper, a new model has been developed which is a two-dimensional program using a finite difference technique and the Marker and Cell (MAC) method to simulate the flow of liquid metal during filling a mould. In the program the Eulerian method has been used for the liquid metal flow, while the Oxide Film Entrainment Tracking Algorithm (OFET) method (a Lagrangian method) has been used to simulate the movement of the oxide film on the liquid metal surface or in the liquid metal flow. Several examples have been simulated and tested and the relevant results were obtained. These results were compared with measured bending strengths. It was found that the completed program was capable of simulating effectively the filling processes of different runner systems. The simulation results are consistent with the experiment. In addition, the program is capable of providing clearer images for predicting the distribution of the oxide film defects generated during filling a mould.

  2. Buckwheat stomatal traits under aluminium toxicity

    Directory of Open Access Journals (Sweden)

    Oleksandr E. Smirnov

    2014-04-01

    Full Text Available Aluminium influence on some stomatal parameters of common buckwheat (Fagopyrum esculentum Moench. was studied. Significant changes in stomatal density, stomatal index and stomatal shape coefficient under aluminium treatment were revealed. Stomatal closure and no difference in total stomatal potential conductance index of treatment plants were suggested as aluminium resistance characteristics.

  3. Does Aluminium Trigger Breast Cancer?

    Directory of Open Access Journals (Sweden)

    Peter Jennrich

    2016-08-01

    Full Text Available Summary. Breast cancer is by far the most common cancer in women in the western world. In 90% of breast cancers, environmental factors are among the causes. The frequency with which the tumour occurs in the outer upper part of the breast has risen with above average rates in recent decades. Aluminium salts as ingredients in deodorants and antiperspirants are being absorbed by the body to a greater extent than hitherto assumed. Their toxicity for healthy and diseased breast tissue cells includes various well-documented pathomechanisms. In the sense of primary and secondary prevention, the cancer-triggering potential of aluminium and its use in anti-perspirant deodorants must be re-evaluated. For the same reason the access to a targeted diagnosis and treatment of aluminium loading must be facilitated.

  4. A novel technique for the deposition of aluminium-doped zinc oxide films

    International Nuclear Information System (INIS)

    Aluminium-doped zinc oxide is used in many applications as a transparent conductive oxide coating. Such coatings are often deposited by DC reactive sputtering of metallic targets, or RF sputtering of ceramic targets. Both of these techniques have their limitations. In the DC case, alloy targets are expensive and only allow a single composition per target. Additionally, in the RF case, targets produced by hot-pressing, or sintering may have a tendency to crack unless sputtered at low powers, thus restricting the deposition rate. However, sputtering from blended powder targets offers a potential solution to all of these problems. In this project, therefore, a series of Al-doped ZnO films have been produced by the pulsed DC magnetron sputtering of blended ZnO/Al2O3 powder targets. Initial results, presented here, indicate that high quality, defect-free films can be produced with suitable electrical and optical properties. The crystallinity of the films has been examined by X-ray diffraction, before and after annealing in controlled atmospheres. A thorough investigation of glass substrate cleaning techniques has also been carried out, with the effectiveness of each technique being assessed in terms of the coating-to-substrate adhesion, as measured by the scratch testing method

  5. Mechanism of Nickel-Aluminium Alloy Electroplating

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The effect of operating conditions on the aluminium content of Ni-Al alloy deposit and the catalytic function of NaF on electrodeposition in the nonaqueous solution containing aluminium are investigated.The results indicate that the plated aluminuim content will be increased with the rise of current density in a given range.When the current density is 2.5A/dm2,nickle-aluminium alloy containing 13.1 wt% aluminium will be deposited.The plated aluminium content will be increased by 2wt% as 0.1mol/L NaF is added to the bath.

  6. Quercetin protects against aluminium induced oxidative stress and promotes mitochondrial biogenesis via activation of the PGC-1α signaling pathway.

    Science.gov (United States)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Verma, Deepika; Priyanka, Kumari; Bal, Amanjit; Gill, Kiran Dip

    2015-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the protective effect of quercetin administration against aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of PGC-1α and its downstream targets, i.e. NRF-1, NRF-2 and Tfam in mitochondrial biogenesis. Aluminium lactate (10mg/kg b.wt./day) was administered intragastrically to rats, which were pre-treated with quercetin 6h before aluminium (10mg/kg b.wt./day, intragastrically) for 12 weeks. We found a decrease in ROS levels, mitochondrial DNA oxidation and citrate synthase activity in the hippocampus (HC) and corpus striatum (CS) regions of rat brain treated with quercetin. Besides this an increase in the mRNA levels of the mitochondrial encoded subunits - ND1, ND2, ND3, Cyt b, COX1, COX3 and ATPase6 along with increased expression of nuclear encoded subunits COX4, COX5A and COX5B of electron transport chain (ETC). In quercetin treated group an increase in the mitochondrial DNA copy number and mitochondrial content in both the regions of rat brain was observed. The PGC-1α was up regulated in quercetin treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α. Electron microscopy results revealed a significant decrease in the mitochondrial cross-section area, mitochondrial perimeter length and increase in mitochondrial number in case of quercetin treated rats as compared to aluminium treated ones. Therefore it seems quercetin increases mitochondrial biogenesis and makes it an almost ideal flavanoid to control or limit the damage that has been associated with the defective mitochondrial function seen in many neurodegenerative diseases.

  7. Electrical behaviour, characteristics and properties of anodic aluminium oxide films coloured by nickel electrodeposition

    OpenAIRE

    Arurault, Laurent; Zamora, Gaël; Vilar, Virginie; Winterton, Peter; Bes, René

    2010-01-01

    Porous anodic films on 1050 aluminium substrate were coloured by AC electrodeposition of nickel. Several experiments were performed at different deposition voltages and nickel concentrations in the electrolyte in order to correlate the applied electrical power to the electrical behaviour, as well as the characteristics and properties of the coatings. The content of nickel inside the coatings reached 1.67 g/m2, depending on the experimental conditions. According to the applied AC voltage in...

  8. The prophylactic reduction of aluminium intake.

    Science.gov (United States)

    Lione, A

    1983-02-01

    The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail. PMID:6337934

  9. Fabrication and optical properties of platinum nanowire arrays on anodic aluminium oxide templates

    Institute of Scientific and Technical Information of China (English)

    高铁仁; 陈子瑜; 彭勇; 李发伸

    2002-01-01

    Arrays of Pt nanowires, fabricated by electrodepositing Pt metal into nanoporous anodic aluminium oxide (AAO)templates, exhibit a preferable optical absorption band in the ultraviolet-visible (UV-VIS) spectra and present a blueshift as the wire aspect ratio increases or its radius decreases. This type of optical property of Pt nanowire/porous alumina composites has been theoretically explored using Maxwell-Garnett (MG) effective medium theory. The MG theory,however, is only applicable to nanowires with an infinitesimally small radius relative to the wavelength of an incident light. The nanowire radius is controlled by the pore radius of the host alumina, which depends on anodizing conditions such as the selected electrolyte, anodizing time, temperature and voltage. The nanowire aspect ratios depend on the amount of Pt deposited into the nanopores of AAO films. The optical absorption properties of the arrays of Pt nanowires with diameters of 24, 55 and 90nm have been investigated by the UV-VIS spectra, which show that the extinction maximum (λmax) shifts to shorter wavelength side as the wire aspect ratio increases or its radius decreases.The results are qualitatively consistent with those calculated based on the MG theory.

  10. Aluminium-doped zinc oxide films prepared by an inorganic sol-gel route

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Rodrigo F.; Zaniquelli, Maria E.D

    2004-02-02

    Thin films of aluminium-doped zinc oxide have been formed on glass using an inorganic sol-gel route and the dip-coating process. The films were formed by the thermal decomposition of a stable precursor colloidal sol prepared by an ethanolic reflux of Zn(CH{sub 3}COO){sub 2}{center_dot}2H{sub 2}O and Al(NO{sub 3}){sub 3}{center_dot}9H{sub 2}O. Lactic acid was used as hydrolysis catalyst and acetylacetone and diethanolamine were added to improve film homogeneity. Thermal analysis was used to investigate the chemical processes during firing of the sols. Atomic force microscopy data revealed morphological changes in the temperature range 200-500 deg. C. The importance of sample firing after each transfer step was evidenced by the quartz crystal microbalance technique. A red shift of the absorption edge was observed for thicker films and the transmittance of the samples decreased with increasing film thickness.

  11. The potential of nanoporous anodic aluminium oxide membranes to influence skin wound repair.

    Science.gov (United States)

    Parkinson, Leigh G; Giles, Natalie L; Adcroft, Katharine F; Fear, Mark W; Wood, Fiona M; Poinern, Gerard E

    2009-12-01

    Cells respond to changes in the environment by altering their phenotype. The ability to influence cell behavior by modifying their environment provides an opportunity for therapeutic application, for example, to promote faster wound healing in response to skin injury. Here, we have modified the preparation of an aluminium oxide template to generate large uniform membranes with differing nano-pore sizes. Epidermal cells (keratinocytes) and dermal cells (fibroblasts) readily adhere to these nanoporous membranes. The pore size appears to influence the rate of cell proliferation and migration, important aspects of cell behavior during wound healing. The suitability of the membrane to act as a dressing after a burn injury was assessed in vivo; application of the membrane demonstrated adherence and conformability to the skin surface of a pig, with no observed degradation or detrimental effect on the repair. Our results suggest that keratinocytes are sensitive to changes in topography at the nanoscale level and that this property may be exploited to improve wound repair after tissue injury.

  12. Indium-doped aluminium oxide as a non-radioactive test aerosol for aerosol experiments

    International Nuclear Information System (INIS)

    For testing inhalation facilities it is advantageous to use a non-radioactive, low toxicity test aerosol which can be detected at low concentrations. These criteria are met by a mechanically generated aerosol of indium-doped alumina. Although some cases of lung fibroses have been associated with the inhalation of aluminium compounds in industry, aluminum oxide aerosols are generally considered to be non-toxic. Indium was chosen as a dopant material because (a) it is not normally present in the lung in detectable amounts, (b) it is chemically similar to aluminum and (c) it can be detected in trace amounts by neutron activation analysis (Friberg et al., 1979). Indium aerosols have the same advantages as radioactive tracers for ease of detection, but they are non-toxic during use. This combination of properties offers advantages that could be of use in a wider range of applications than hitherto used, e.g. in inhalation experiments. This paper describes nose-only inhalation experiments on rats using an aerosol of alumina doped with indium. (author)

  13. Surface decoration of anodic aluminium oxide in synthesis of Nafion (registered) -115 nanowire arrays

    International Nuclear Information System (INIS)

    An extrusion method, using anodic aluminium oxide (AAO) membranes as templates, has been developed to fabricate Nafion[reg] -115 nanowire arrays. Surface decoration of the templates plays an important role in the synthesis of the Nafion[reg] -115 nanowire arrays. By using sodium dodecyl sulfate (SDS) as a surfactant in the surface decoration, the filling rate of the Nafion[reg] -115 nanowires in the corresponding template exceeds 95%, compared with the filling rate of 42% in an undecorated template, while on using cetyltrimethylammonium bromide (CTAB) as a surfactant, the filling rate is only about 20%. Systematical investigations show that the effect of surface decoration is induced by the combination of surface tension and electrostatic force (radial component), of which the radial component of the electrostatic force is more important. This effect is significant in organic nanowire fabrication; furthermore, the as-synthesized organic nanowires would have potential application such as in organic electronics, optoelectronic devices, and nanoscale proton exchange membrane fuel cells

  14. Gold-Catalyzed Growth of Aluminium-Doped Zinc Oxide Nanorods by Sputtering Method

    Directory of Open Access Journals (Sweden)

    A. B. Rosli

    2014-01-01

    Full Text Available Aluminium-doped zinc oxide (AZO nanorods thin films were grown by RF magnetron sputtering on gold (Au metal catalyst. The Au catalyst layers with 5, 10, and 15 nm thickness were deposited on glass substrates by sputtering method followed by annealing for 15 min at 500°C to form Au nanostructures on the glass substrate. The AZO thin films were then deposited on the Au catalyst at different deposition temperature varying from 200 to 500°C. Postdeposition annealing processes of the Au catalyst resulted in different morphologies of the Au catalyst layers depending on their thicknesses. This in turn gave different AZO morphologies which suggest that the Au catalyst layer thickness and the deposition temperature contribute to the growth mechanism of the AZO nanostructures. AZO nanorods thin films having hexagonal wurtzite structure with individual nanorods on the film surface were obtained from the samples deposited on 5 and 10 nm thick Au catalyst with the deposition temperature of 300°C.

  15. Nanowires: properties, applications and synthesis via porous anodic aluminium oxide template

    Indian Academy of Sciences (India)

    Jaya Sarkar; Gobinda Gopal Khan; A Basumallick

    2007-06-01

    Quasi one-dimensional nanowires possess unique electrical, electronic, thermoelectrical, optical, magnetic and chemical properties, which are different from that of their parent counterpart. The physical properties of nanowires are influenced by the morphology of the nanowires, diameter dependent band gap, carrier density of states etc. Nanowires hold lot of promises for different applications. Basic electronic devices like junction diodes, transistors, FETs and logic gates can be fabricated by using semiconductor and superlattice nanowires. Thermoelectric cooling system can be fabricated by using metallic nanowires. Semiconductor nanowire junctions can be used for different opto-electronic applications. Moreover, periodic arrays of magnetic nanowires hold high potential for recording media application. Nanowires are also potential candidates for sensor and bio-medical applications. In the present article, the physical and chemical properties of nanowires along with their probable applications in different fields have been reviewed in detail. The review also includes highlights of the synthesis of nanowires via porous anodic aluminium oxide template since the technique is simple, cost-effective and a low temperature technique.

  16. Oxide growth on aluminium alloys in the presence of ammonium fluoborate

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, J.; Paterson, P.; Flavell, T. [Royal Melbourne Inst. of Tech., VIC (Australia); Biddle, G. [Alcoa Rolled Products (Australia)

    1996-12-31

    The aim of this study as to determine the mechanisms involved in using ammonium fluoborate as a reducing atmosphere when preheating a high magnesium content aluminium alloy. Rutherford Backscattering (RBS) has been the major technique used in the analysis of samples, it revealed significant reduction in both the diffusion of magnesium to the surface and the calculated oxide thickness in the presence of NH{sub 4}BF{sub 4}. At temperatures above 500 deg C in air, SEM images revealed depressions and voids due to incipient melting at various stages, around the grain boundaries. Grain boundaries effectively acted as pipes aiding the diffusion of magnesium to the surface. These results have been verified through compositional analysis with both RBS and auger electron spectroscopy (AES). Results from NH{sub 4}BF{sub 4} atmosphere preheat conditions showed significant improvements. It was verified experimentally that above 500 deg C , AA5182 alloys undergo incipient melting at the grain boundaries with magnesium diffusing through to the surface. 5 refs., 1 fig.

  17. Electrochemical properties and thermal stability of epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    ZORICA M. KACAREVIC-POPOVIC

    2001-12-01

    Full Text Available The corrosion behaviour of epoxy coatings electrodeposited on aluminium, as well as on electrochemically and chemically modified aluminium were investigated during exposure to 3 % NaCl. Electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA were used for the determination of the protective properties of epoxy coatings on aluminium, anodized aluminium, phosphatized and chromatized-phosphatized aluminium. The protective properties of epoxy coatings on anodized and chromatized-phosphatized aluminium are significantly improved with respect to the same epoxy coatings on aluminium and phosphatized aluminium: higher values of the pore resitance and charge-transfer resistance, lower values of the coating capacitance, double-layer capacitance and relative permittivity (from EIS smaller amount of absorbed water inside the coating (From TGA. On the other hand, the lower values of the ipdt temperature indicate a lower thermal stability of the epoxy coatings on anodized and chromatized-phosphatized aluminium.

  18. Recovery mechanisms in nanostructured aluminium

    DEFF Research Database (Denmark)

    Yu, Tianbo; Hansen, Niels; Huang, Xiaoxu

    2012-01-01

    Commercial purity aluminium (99.5%) has been cold rolled to a true strain of 5.5 (99.6% reduction in thickness). The material is very strong but low temperature recovery may be a limiting factor. This has been investigated by isothermal annealing treatments in the temperature range 5–100C. Hardness...

  19. Constitutive modelling of aluminium foams

    NARCIS (Netherlands)

    Wang, W.M.; Lemmen, P.P.M.

    2001-01-01

    In this paper an aluminium foam model is proposed for a vehicle crash analysis. The model assumes that there is no coupling between stresses and strains in different principal directions. The stress in each principle direction is then interpolated from an experimental recorded uniaxial stress strain

  20. Microchemistry in aluminium sheet production

    NARCIS (Netherlands)

    Lok, Z.J.

    2005-01-01

    The production of aluminium sheet alloys from as-cast ingots is a complex process, involving several rolling operations in combination with various thermal heat treatments. Through their influence on the alloy microchemistry and microstructure, these thermomechanical treatments are all aimed at cont

  1. Marker behaviour of implanted xenon during the anodic oxidation of aluminium: evidence and interpretation of dose dependant splitting effect

    International Nuclear Information System (INIS)

    Using 2 MeV lithium ions backscattering and transmission electron microscopy techniques, a part of xenon atoms introduced by implantation in aluminium metal under the initial oxide layer is shown to be tranported by the moving metal-oxide interface during anodic oxidation. From specific anodization conditions (V sup(ct), T = 900C) this splitting of the initial xenon distribution is interpreted in terms of bubble formation and growth above a given local concentration threshold. A schematic model for this behaviour evolution is proposed. This dose dependance is of practical interest in the determination of transport numbers. Although unambiguously measured they may be subject to significant systematic uncertainties which are discussed

  2. Influence of Nanowire Diameter on Structural and Optical Properties of cu Nanowire Synthesized in Anodic Aluminium Oxide Film

    Science.gov (United States)

    Cetinel, A.; Özcelik, Z.

    2016-11-01

    Copper (Cu) nanowire arrays embedded in anodic aluminium oxide films (AAO) on aluminium substrate have been synthesized by alternating current electrochemical deposition. Two-step anodization process has been performed to get the through-hole AAO with ordered nanochannels in 0.3M oxalic acids at DC voltages 30, 40, 50 and 60V, respectively. Structural characterization of the Cu nanowires has been analyzed by scanning electron microscopy (SEM) and X-ray diffraction (or) X-ray diffractometer (XRD). Our SEM analysis has revealed that the diameters of vertically oriented Cu nanowires are 15, 25, 45 and 60nm and the length of Cu nanowires having high packing density is about 15μm. XRD measurement has indicated that polycrystalline Cu nanowires prefer growth orientation along the (111) direction. Optical measurements show that reflection of the Cu nanowires/AAO on aluminium reduces with decreasing diameter of the Cu nanowires. This effect can be associated with increased light scattering from metal nanoparticles near their localized plasmon resonance frequency depending on the size and shape of the nanoparticles.

  3. Bumblebee pupae contain high levels of aluminium.

    Science.gov (United States)

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  4. Friction Welding of Aluminium and Aluminium Alloys with Steel

    Directory of Open Access Journals (Sweden)

    Andrzej Ambroziak

    2014-01-01

    Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

  5. Self-sealing of unsealed aluminium anodic oxide films in very different atmospheres

    Directory of Open Access Journals (Sweden)

    González, J. A.

    2003-12-01

    Full Text Available It is widely believed that the corrosion resistance behaviour of bare aluminium in natural environments is superior to that of unsealed anodised aluminium. However, results obtained in the exposure of unsealed anodised aluminium specimens with three different film thicknesses, in 9 atmospheres of Ibero-America with salinity levels between 3.9 and 517 mg.m-2.d-1 chloride, clearly shows the reverse to be true. After a sufficient time, which is shorter the higher the precipitation rate and the environmental relative humidity, a self-sealing process takes place, leading to coatings that surpass the quality standards demanded in industrial practice. Anodic films, sealed and unsealed, are protective coatings whose quality improves with ageing in most natural environments.

    Está muy difundida la idea de que el comportamiento del aluminio es superior al del aluminio anodizado y sin sellar, desde el punto de vista de la resistencia a la corrosión, en los ambientes naturales. Sin embargo, los resultados obtenidos en la exposición de anodizados sin sellar, de tres espesores diferentes, a 9 atmósferas de Iberoamérica, con salinidades comprendidas entre 3,9 y 517 mg.m-2.d-1 de cloruros, muestran, sin lugar a dudas, lo contrario. Con tiempo suficiente, tanto más rápidamente cuanto mayor sean las precipitaciones y la humedad relativa ambiental, tiene lugar un proceso de autosellado que conduce a recubrimientos que superan las normas de calidad exigidas en la práctica industrial. Los anodizados, sellados y sin sellar, son recubrimientos protectores que mejoran su calidad, en la mayoría de los ambientes naturales, con el envejecimiento.

  6. FIB-SEM investigation of trapped intermetallic particles in anodic oxide films on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.;

    2011-01-01

    using focused ion beam-scanning electron microscopy (FIB-SEM), SEM, and EDX. Findings - The intermetallic particles in the substrate material consisted of Fe or both Fe and Si with two different structures: irregular and round shaped. FIB-SEM cross-sectioned images revealed that the irregular....../Si ratio of the intermetallic particles decreased after anodizing. Originality/value - This paper shows that dual beam FIB-SEM seems to be an easy, less time consuming and useful method to characterize the cross-sectioned intermetallic particles incorporated in anodic film on aluminium....

  7. Oxidation of an aluminium-magnesium alloy in liquid state. Methodology of determination of mechanisms from not necessarily repeatable experiments

    International Nuclear Information System (INIS)

    This research thesis reports the study of the oxidation of an aluminium-5 pc magnesium alloy in its liquid state in an oxygen environment, using thermogravimetric analysis and that of magnesium in its solid state. In a first part, the author reports a thermodynamic and bibliographical study on magnesium transformation in its solid state (Mg/O2 and Mg/H2O systems, transformation with dry and humid synthetic air, oxidation inhibitors) and on Al-Mg alloy transformation in presence of oxygen (thermodynamic properties of aluminium-rich Al-Mg alloys, Al-Mg/O2/N2 and Al-Mg/O2/N2/H2O systems). The next parts address the selection of reaction systems for the different cases (oxidation of solid magnesium in oxygen, oxidation of the Al-Mg alloy in oxygen), the modelling of the formation of magnesia from solid magnesium and from the Al-Mg alloy, and the modelling of the liquid Al-Mg A5182 alloy oxidation in oxygen

  8. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

  9. Aluminium in Allergies and Allergen immunotherapy.

    Science.gov (United States)

    Jensen-Jarolim, Erika

    2015-01-01

    Aluminium is a hot topic in the current debate. Exposure occurs due to environmental, dietary and intentional exposure to aluminium, such as in vaccines where it was introduced in 1926. In spite of the fact that it is a typical Th2 adjuvant, aluminium redirects the immune response in systemic allergen immunotherapy (SIT) upon prolonged immunization. SIT in the US, and SLIT in general, are at present non-adjuvanted therapies, but in Europe aluminium is used as adjuvant in most SIT preparations. It enhances the safety of SIT by local deposition of the allergen. Undesired properties of aluminium adjuvants comprise acute and chronic inflammation at the injection site, its Th2 immune stimulatory capacity, its accumulation besides biodistribution in the body. The adjuvant and safety profile of aluminium adjuvants in allergy vaccines are discussed, as well as the need for putting modern delivery systems and adjuvants on the fast track.

  10. Dietary aluminium Intake Level for Rent Animals in a Primary and Secondary Aluminium Industry Surrounding Area

    OpenAIRE

    Mărioara Drugă; Alexandru Trif; Mihai Drugă; Ducu Ştef; Ştefan Munteanu

    2010-01-01

    The study was carried out in an aluminium industry surrounding area on purpose to evaluate dietary aluminium intake level for rent animals originated from fodder and water consumed by them. There were taken feed and water samples in different periods and from increasing distances from industrial platform, determined the aluminium level by atomic spectroscopy and calculated the rations for cattle and poultry. Conclusions: aluminium dietary intake level by ration depends by forage period for st...

  11. Does Aluminium Trigger Breast Cancer?

    OpenAIRE

    Peter Jennrich; Claus Schulte-Uebbing

    2016-01-01

    Summary. Breast cancer is by far the most common cancer in women in the western world. In 90% of breast cancers, environmental factors are among the causes. The frequency with which the tumour occurs in the outer upper part of the breast has risen with above average rates in recent decades. Aluminium salts as ingredients in deodorants and antiperspirants are being absorbed by the body to a greater extent than hitherto assumed. Their toxicity for healthy and diseased breast tissue cells includ...

  12. A biogeochemical cycle for aluminium?

    Science.gov (United States)

    Exley, Christopher

    2003-09-15

    The elaboration of biogeochemical cycles for elements which are known to be essential for life has enabled a broad appreciation of the homeostatic mechanisms which underlie element essentiality. In particular they can be used effectively to identify any part played by human activities in element cycling and to predict how such activities might impact upon the lithospheric and biospheric availability of an element in the future. The same criteria were the driving force behind the construction of a biogeochemical cycle for aluminium, a non-essential element which is a known ecotoxicant and a suspected health risk in humans. The purpose of this exercise was to examine the concept of a biogeochemical cycle for aluminium and not to review the biogeochemistry of this element. The cycle as presented is rudimentary and qualitative though, even in this nascent form, it is informative and predictive and, for these reasons alone, it is deserving of future quantification. A fully fledged biogeochemical cycle for aluminium should explain the biospheric abundance of this element and whether we should expect its (continued) active involvement in biochemical evolution.

  13. A bakable aluminium vacuum chamber with an aluminium flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the construction of the vacuum chamber in proton synchrotrons and electron storage rings. (author)

  14. Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

    Energy Technology Data Exchange (ETDEWEB)

    Moe, J. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

  15. Nanoscale carbon tubules deposited in anodic aluminium oxide template:a study of soft x-ray transmission

    Institute of Scientific and Technical Information of China (English)

    Liu Li-Feng; Zhou Zhen-Ping; Yuan Hua-Jun; Ci Li-Jie; Liu Dong-Fang; Gao Yan; Wang Jian-Xiong; Wang Gang; Zhou Wei-Ya; Zhu Pei-Ping; Cui Ming-Qi; Zheng Lei; Zhu Jie; Zhao Yi-Dong; Song Li; Yan Xiao-Qin

    2004-01-01

    Well-aligned, catalyst-free nanoscale carbon tubules array was prepared by organic compound vapour deposition method using anodic aluminium oxide (AAO) as a template. The experiment of soft x-ray channelling in such carbon tubules array deposited in AAO template was performed at Beijing Synchrotron Radiation Facility. The transmission of x-rays in carbon tubules array with AAO template support was found even higher than that in bare AAO template at high-energy part of energy spectrum though the porous area of the former was smaller than that of the latter. A qualitative explanation is presented to interpret our results.

  16. Aluminium in foodstuffs and diets in Sweden.

    Science.gov (United States)

    Jorhem, L; Haegglund, G

    1992-01-01

    The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources. PMID:1542992

  17. Effect of pressurized steam on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

    2012-01-01

    Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

  18. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions.

    Science.gov (United States)

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits. PMID:27403611

  19. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    Science.gov (United States)

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-07-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits.

  20. Aluminium exclusion and aluminium tolerance in woody plants

    OpenAIRE

    Ivano eBrunner; Christoph eSperisen

    2013-01-01

    The aluminium (Al) cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion...

  1. Preparation of aluminium lakes by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Prapai Pradabkham

    2008-07-01

    Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  2. Acoustic properties of aluminium foams

    Directory of Open Access Journals (Sweden)

    García, L. E.

    2008-09-01

    Full Text Available The article discusses normal incidence sound absorption by aluminium foam manufactured with powder metallurgy technology. Aluminium foams with different surface morphologies were obtained by varying the type of precursor and adding filler materials during the foaming process. The sound absorption coefficients found for these aluminium foams were compared to the coefficient for commercial foams marketed under the name ALPORAS. The effect of foam thickness on the absorption coefficient was studied for each sample prepared. The combination of good acoustic and mechanical properties makes aluminium foams particularly attractive products. The study included an analysis of the effect of 2-, 5- and 10-cm air gaps on the sound absorption coefficient. The results showed that such gaps, which are routinely used in construction to reduce the reverberation period in indoor premises, raised the low frequency absorption coefficient significantly. This increase was found to depend on aluminium foam density and thickness and the depth of the air gap. In this same line, we have investigated the absorption coefficient of the aluminium foams combined with a mineral fiber panel.Se presenta un estudio del coeficiente de absorción acústica a incidencia normal de espumas de aluminio fabricadas mediante la técnica pulvimetalúrgica. Se fabricaron espumas de aluminio de distinta morfología superficial variando el tipo de precursor y usando materiales de relleno durante el proceso de espumación. Se muestra un estudio comparativo del coeficiente de absorción acústica de las espumas de aluminio fabricadas y las espumas comerciales conocidas como ALPORAS. Para cada muestra fabricada se estudió la influencia del espesor sobre el valor del coeficiente de absorción.El atractivo de las espumas de aluminio radica en que en ellas se combinan interesantes propiedades acústicas y mecánicas. Se analizó el efecto de una cámara de aire de 2, 5 y 10 cm de anchura sobre el

  3. Application of phosphating techniques to aluminium and carbon steel surfaces using nitro guanidine as oxidizing agent

    International Nuclear Information System (INIS)

    Phosphate coatings are inorganic crystalline deposits laid down uniformly on properly prepared surfaces by a chemical reaction with the treated base metal. The reaction consists in dissolving some surface metal by acid attack and then causing surface neutralization of the phosphate solution with consequent precipitation of the phosphate coating. Phosphate coatings do not provide appreciable corrosion protection in themselves. They are useful mainly as a base for paints, ensuring good adherence of paint to steel and decreasing the tendency for corrosion to under cut the paint film at scratches or other defects. In this work firstly were realized phosphate on standard carbon steel, employing technical of cold phosphate (at 40 Centigrade degrees and with a treatment time of 30 minutes) and hot phosphate (at 88 Centigrade degrees and with a treatment time of 15 minutes), where with this last were obtained the best results. Both methods used phosphate solutions of Zn/Mn and using as catalyst Nitro guanidine. Aluminium surfaces were phosphate used solutions of Cr and as catalyst Sodium bi fluoride. The phosphating on this surface were realized at temperature of 50 Centigrade degrees and with a treatment time of 10 minutes. In this work were obtained a new phosphate coatings on steel surfaces, these coatings were realized with a phosphate solution manufactured with the precipitates gathered during the hot phosphating on carbon steel. These coatings show excellent physical characteristics and of corrosion resistance. Were determined the physical testings of the coatings phosphate obtained on carbon steel and aluminium surfaces. These testing were: roughness, thickness, microhardness and adhesion. The best results were showed in carbon steel phosphate with precipitated solutions. The technical of analysis for activation with thermic neutrons was used to determine the phosphate coatings composition. Finally, corrosion testings were realized by means of two methods

  4. Accelerated growth of oxide film on aluminium alloys under steam: Part II: Effects of alloy chemistry and steam vapour pressure on corrosion and adhesion performance

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Bordo, Kirill; Jellesen, Morten Stendahl;

    2015-01-01

    The steam treatment of aluminium alloys with varying vapour pressure of steamresulted in the growth of aluminium oxyhydroxide films of thickness range between 450 - 825nm. The surface composition, corrosion resistance, and adhesion of the produced films was characterised by XPS, potentiodynamic...... polarization, acetic acid salt spray, filiform corrosion test, and tape test. The oxide films formed by steam treatment showed good corrosion resistance in NaCl solution by significantly reducing anodic and cathodic activities. The pitting potential of the surface treated with steam was a function...

  5. Manipulation of stored charge in anodic aluminium oxide/SiO2 dielectric stacks by the use of pulsed anodisation

    Science.gov (United States)

    Lu, Zhong; Ouyang, Zi; Grant, Nicholas; Wan, Yimao; Yan, Di; Lennon, Alison

    2016-02-01

    A method of fabricating anodic aluminium oxide (AAO) with the capability of manipulating its stored charge is reported. This method involves the use of a pulsed current source to anodise aluminium layers instead of the typically used constant current/voltage source, with the test structures experiencing positive and negative cycles periodically. By tuning the positive cycle percentage, it is demonstrated that the effective stored charge density can be manipulated in a range from -5.2 × 1011 to 2.5 × 1012 q/cm2 when the AAO is formed over a 12 nm SiO2 layer. An investigation of the stored charge distribution in the dielectric stacks indicates a positive fixed charge at the SiO2/Si interface, a negative fixed charge at the AAO/SiO2 interface and a positive bulk charge within the AAO layer. The effective stored charge density and interface states were found to be affected by annealing conditions and it is suggested that oxygen annealing can reduce the bulk positive charge while post-metallisation anneal is most effective in reducing silicon interface defects. Charge manipulation using pulsed anodisation is shown to reduce carrier recombination on boron-diffused silicon surfaces highlighting the potential of the process to be used to tune the electrical properties of dielectric layers so that they can reduce surface recombination on silicon surfaces having different dopant polarity and concentrations.

  6. Morphology, thermal, electrical and electrochemical stability of nano aluminium-oxide-filled polyvinyl alcohol composite gel electrolyte

    Indian Academy of Sciences (India)

    Navin Chand; Neelesh Rai; S L Agrawal; S K Patel

    2011-12-01

    In the present work, an attempt has been made to develop nano aluminium oxide (Al2O3)-filled polyvinyl alcohol (PVA) composite gel electrolytes. Surface morphological studies, thermal behaviour, electrochemical stability and electrical characterization of these composite gel electrolytes have been performed. An increase in the concentration of Al2O3 in composite gel electrolytes increases the amorphous characteristics of pure PVA. Bulk conductivity of composite gel electrolytes increases by an order of magnitude on addition of a nano filler. Maximum conductivity of 5.81 × 10-2 S/cm is observed for 6 wt% Al2O3-filled polymer gel composite electrolytes. Temperature dependence of electrical conductivity shows a combination of Arrhenius and Vogel–Tamman–Fulcher (VTF) nature. Maximum current stability during oxidation and reduction cycle is noticed for 6 wt% Al2O3-filled PVA composite electrolyte, viz. ±1.65 V.

  7. LETTER TO THE EDITOR: Aluminium oxide ultrathin-film growth on the Mo(110) surface: a work-function study

    Science.gov (United States)

    Magkoev, T. T.; Vladimirov, G. G.

    2001-07-01

    Submonolayer-to-multilayer films deposited onto the surface of Mo(110) crystal by thermal evaporation of bulk aluminium oxide in ultrahigh vacuum have been studied by Auger electron spectroscopy, low-energy electron diffraction and work-function measurements (the Anderson method). The Auger spectra of the films at all coverages studied are composed of the lines characteristic for the bulk oxide; no evidence of a metallic Al signal is found. The layer-by-layer growth mode occurs up to two monolayers. Increase of the reflectivity of the low-energy electrons (1 to 4 eV) as the film grows indicates that the film has a reduced density of states, which probably resembles the band gap of the bulk alumina. The films deposited on a substrate held at room temperature are amorphous, whereas deposition at 1300 K results in a hexagonal superstructure.

  8. Shot peening of aluminium alloys

    International Nuclear Information System (INIS)

    Shot peening is a process of cold-hammering where a metallic surface is pelted with spherical grains. Each grain bumping into the surface acts as a hammer head and creates a small crater. The overlapping of these craters produces a residual compression layer just underneath the surface. It is well known that cracks cannot spread in a compression zone. In most cases of fatigue rupture and stress corrosion cracks propagate from the surface towards the inside so shot peening allows a longer lifetime of castings. Moreover most materials present a better resistance due to the cold-hammering effect of shot peening. Metallic surfaces can be treated in workshops or directly on site. Typical pieces that undergo shot peening on site are storing tanks, gas and steam turbines, tubes of steam generators and piping in oil or nuclear or chemical industries. This article describes shot peening from a theoretical and general point of view and presents the application to aluminium-lithium alloys. In the case of aluminium alloys shot peening can be used to shape the piece (peen-forming). (A.C.)

  9. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  10. Trophic transfer potential of aluminium oxide nanoparticles using representative primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia)

    International Nuclear Information System (INIS)

    Highlights: • Trophic transfer of alumina nanoparticles using Chlorella ellipsoides and Ceriodaphnia dubia. • Subtle alterations in the feeding behaviour of the daphnids. • Disruption the energy flow through the food chain. • Transmission electron microscopy validated the disrupted feeding behaviour. - Abstract: The transfer of nanoparticles through the food chain can lead to bioaccumulation and biomagnification resulting in a long term negative impact on the ecosystem functions. The primary objective of this study was evaluation of aluminium oxide nanoparticles transfer from primary producers to primary consumers. A simple set up consisting of a primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia) was used. Here, C. ellipsoides were exposed to the varying concentrations of the nanoparticles ranging from 20 to 120 μg/mL (196 to 1176 μM) for 48 h and the infested algal cells were used as the feed to C. dubia. The bioaccumulation of the nanoparticles into the daphnids was noted and the biomagnification factors were computed. The exposure was noted to cause subtle alterations in the feeding behaviour of the daphnids. This might have long term consequences in the energy flow through the food chain. The reproductive behaviour of the daphnids remained unaffected upon exposure to nanoparticle infested algal feed. Distinct observations at ultra-structural scale using transmission electron microscopy provided visual evidences for the disrupted feeding behaviour upon exposure to nanoparticle treated algae. Internalization of nanoparticle like inclusion bodies in the intracellular space of algae was also detected. The findings were further substantiated by a detailed analysis of hydrodynamic stability, bioavailability and dissolution of ions from the nanoparticles over the exposure period. Altogether, the study brings out the first of its kind of observation of trophic transfer potential/behaviour of aluminium oxide nanoparticles and

  11. Trophic transfer potential of aluminium oxide nanoparticles using representative primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia)

    Energy Technology Data Exchange (ETDEWEB)

    Pakrashi, Sunandan; Dalai, Swayamprava; Chandrasekaran, Natarajan; Mukherjee, Amitava, E-mail: amit.mookerjea@gmail.com

    2014-07-01

    Highlights: • Trophic transfer of alumina nanoparticles using Chlorella ellipsoides and Ceriodaphnia dubia. • Subtle alterations in the feeding behaviour of the daphnids. • Disruption the energy flow through the food chain. • Transmission electron microscopy validated the disrupted feeding behaviour. - Abstract: The transfer of nanoparticles through the food chain can lead to bioaccumulation and biomagnification resulting in a long term negative impact on the ecosystem functions. The primary objective of this study was evaluation of aluminium oxide nanoparticles transfer from primary producers to primary consumers. A simple set up consisting of a primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia) was used. Here, C. ellipsoides were exposed to the varying concentrations of the nanoparticles ranging from 20 to 120 μg/mL (196 to 1176 μM) for 48 h and the infested algal cells were used as the feed to C. dubia. The bioaccumulation of the nanoparticles into the daphnids was noted and the biomagnification factors were computed. The exposure was noted to cause subtle alterations in the feeding behaviour of the daphnids. This might have long term consequences in the energy flow through the food chain. The reproductive behaviour of the daphnids remained unaffected upon exposure to nanoparticle infested algal feed. Distinct observations at ultra-structural scale using transmission electron microscopy provided visual evidences for the disrupted feeding behaviour upon exposure to nanoparticle treated algae. Internalization of nanoparticle like inclusion bodies in the intracellular space of algae was also detected. The findings were further substantiated by a detailed analysis of hydrodynamic stability, bioavailability and dissolution of ions from the nanoparticles over the exposure period. Altogether, the study brings out the first of its kind of observation of trophic transfer potential/behaviour of aluminium oxide nanoparticles and

  12. Dietary aluminium Intake Level for Rent Animals in a Primary and Secondary Aluminium Industry Surrounding Area

    Directory of Open Access Journals (Sweden)

    Mărioara Drugă

    2010-05-01

    Full Text Available The study was carried out in an aluminium industry surrounding area on purpose to evaluate dietary aluminium intake level for rent animals originated from fodder and water consumed by them. There were taken feed and water samples in different periods and from increasing distances from industrial platform, determined the aluminium level by atomic spectroscopy and calculated the rations for cattle and poultry. Conclusions: aluminium dietary intake level by ration depends by forage period for studied species, rations structure and distance from industrial platform and didn’t reach toxic level in any case.

  13. Aluminium Process Fault Detection and Diagnosis

    Directory of Open Access Journals (Sweden)

    Nazatul Aini Abd Majid

    2015-01-01

    Full Text Available The challenges in developing a fault detection and diagnosis system for industrial applications are not inconsiderable, particularly complex materials processing operations such as aluminium smelting. However, the organizing into groups of the various fault detection and diagnostic systems of the aluminium smelting process can assist in the identification of the key elements of an effective monitoring system. This paper reviews aluminium process fault detection and diagnosis systems and proposes a taxonomy that includes four key elements: knowledge, techniques, usage frequency, and results presentation. Each element is explained together with examples of existing systems. A fault detection and diagnosis system developed based on the proposed taxonomy is demonstrated using aluminium smelting data. A potential new strategy for improving fault diagnosis is discussed based on the ability of the new technology, augmented reality, to augment operators’ view of an industrial plant, so that it permits a situation-oriented action in real working environments.

  14. Deformation features of aluminium in tensile tests

    International Nuclear Information System (INIS)

    It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 4000C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.)

  15. Steam Initiated Surface Modification of Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud

    , crystalline nano-particles, role of steam-based treatment on adhesion of industrially applied powder coating, and investigations of a failed painted aluminium window profile due to defects in the extruded profile. Chapters 13 and 14 describe the overall discussion, conclusions and future work based......The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco...

  16. Shear Viscosity of Aluminium under Shock Compression

    Institute of Scientific and Technical Information of China (English)

    LIU Fu-Sheng; YANG Mei-Xia; LIU Qi-Wen; CHEN Jun-Xiang; JING Fu-Qian

    2005-01-01

    @@ Based on the Newtonian viscous fluid model and the analytic perturbation theory of Miller and Ahrens for the oscillatory damping of a sinusoidal shock front, a flyer-impact technique is developed to investigate the effecti veviscosity of shocked aluminium.

  17. Bone marrow aluminium storage in renal failure.

    OpenAIRE

    Kaye, M.

    1983-01-01

    Using the staining method for aluminium with the ammonium salt of aurine tricarboxylic acid, aluminon, 18 patients with end stage renal disease gave positive reactions in iliac crest bone biopsies and 11 of these had positive staining in the bone marrow. In one the marrow was positive and the bone negative. The marrow reaction is putatively regarded as caused by aluminium storage in unidentified cells, possibly of the macrophage system which are strongly fluorescent when examined after prior ...

  18. DETERMINATION OF IMPURITY ELEMENTS IN ALUMINIUM

    Institute of Scientific and Technical Information of China (English)

    侯小琳; 张永保

    1994-01-01

    Twenty five impurity elements in aluminium applied as reactor material are determined.Titanium and nickel are determined with epithermal neutron activation analysis(NAA),magnesium and silicon by inductance coupling plasma emission spectra(ICP),other elements by thermal NAA.The fission coefficient of uranium is given by an experiment,the interferences of uranium to Ce,Nd,Mo,Zr,La,Sm are subtracted.The detection limits of these methods to all of impurity elements in aluminium are calculated.

  19. Silane based coating of aluminium mold

    DEFF Research Database (Denmark)

    2013-01-01

    having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...... of structures which would otherwise be difficult to mold. The resistance of the coated aluminium mold is significantly improved by applying a silane-based coating layer....

  20. Electrical Conductivity of Aluminium Alloy Foams

    Institute of Scientific and Technical Information of China (English)

    凤仪; 郑海务; 朱震刚; 祖方遒

    2002-01-01

    Closed-cell aluminium alloy foams were produced using the powder metallurgical technique. The effect of porosityand cell diameter on the electrical conductivity of foams was investigated and the results were compared with anumber of models. It was found that the percolation theory can be successfully applied to describe the dependenceof the electrical conductivity of aluminium alloy foams on the relative density. The cell diameter has a negligibleeffect on the electrical conductivity of foams.

  1. Nano structured porous anodized aluminium oxide by using C2H2O4 for electronic applications: Study of the cell potential effects on formation of porous alumina

    International Nuclear Information System (INIS)

    In this research, a nano porous anodized aluminium oxide AAO thin film was successfully grown onto oxide layer on silicon substrate. The anodization of Si/ SiO2/ Al substrate was conducted in a vigorous stirring oxalic acid bath solution. The rate of growth, morphology and also the kinetic study of the AAO thin film were investigated. The resulting array, pores structure and pores density of AAO strongly depends on an applied voltage of the anodizing process. (author)

  2. Heat treatment of aluminium strip coils; Gluehbehandlung von Aluminium-Bandbunden

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, Dominik; Dambauer, Georg [LOI Thermprocess GmbH, Essen (Germany)

    2012-08-15

    Nowadays, aluminium strip coils are increasingly heat-treated in single-coil lifting hearth furnaces SCL. Flexible, individual heat treatment allows fast reactions to short term requirements for the production of aluminium strip and offers energy saving possibilities. The following report describes the advantages of single-coil hearth furnaces in terms of flexibility, energy consumption and possible configurations. (orig.)

  3. A preliminary study of the dermal absorption of aluminium from antiperspirants using aluminium-26.

    Science.gov (United States)

    Flarend, R; Bin, T; Elmore, D; Hem, S L

    2001-02-01

    Aluminium chlorohydrate (ACH), the active ingredient in many antiperspirants, was labeled with the radioisotope 26Al. The labeled ACH was then fractionated into about 100 samples using gel filtration chromatography. Each fraction was analyzed for 26Al and total aluminium content. Aluminium-26 was only detected in the fractions that also contained aluminium, which verified that the ACH was uniformly labeled. 84 mg of the labeled ACH was then applied to a single underarm of two adult subjects with blood and urine samples being collected over 7 weeks. Tape-stripping and mild washings of the skin were also collected for the first 6 days. Results indicate that only 0.012% of the applied aluminium was absorbed through the skin. At this rate, about 4 microg of aluminium is absorbed from a single use of ACH on both underarms. This is about 2.5% of the aluminium typically absorbed by the gut from food over the same time period. Therefore, a one-time use of ACH applied to the skin is not a significant contribution to the body burden of aluminium.

  4. Design of welded aluminium connections (Entwurf und Berechnung von Aluminium Schweissverbindungen)

    NARCIS (Netherlands)

    Soetens, F.

    1998-01-01

    In the past two decades considerable research effort has been put into welded aluminium connections in order to better understand their structural behaviour and to up-date the design rules in the existing standards at the time [1]. Since weids in aluminium are more critical compared to steel, the ab

  5. Aluminium exclusion and aluminium tolerance in woody plants

    Directory of Open Access Journals (Sweden)

    Ivano eBrunner

    2013-06-01

    Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

  6. Preparation and investigations of thermal properties of copper oxide, aluminium oxide and graphite based on new organic phase change material for thermal energy storage

    Indian Academy of Sciences (India)

    Murat Genc; Betul Inci; Zuhal Karagoz Genc; Canan Aksu Canbay; Memet Sekercı

    2015-04-01

    The effects of copper oxide, aluminium oxide and graphite on the thermal and structural properties of the organic phase change material (PCM) were investigated. Ethyl 2-(1H-benzotriazole-1-yl)acetate was selected as the pure PCM. Fourier transform infrared (FT-IR) spectroscopy, X-ray, energy dispersive X-ray (EDX) and scanning electron microscope (SEM) were used to determine the chemical structure, crystalloid phase, chemical composition and microstructure of the composites, respectively. The thermal properties were investigated by differential scanning calorimetry and thermogravimetric analyzer. The FT-IR analyses indicated that there was no chemical interaction between the pure PCM and the supporting materials such as copper oxide, aluminium oxide and graphite. The X-ray diffractograms of the samples were nearly the same, but the peak intensities changed according to the supporting materials. The SEM results showed that the C, N and O elements were well adsorbed into the porous network of the graphite, Al2O3 and CuO. According to the supporting materials, the graphite had the minimum porosity and the maximum crystallite size.

  7. Accumulation of Aluminium and Physiological Status of Tree Foliage in the Vicinity of a Large Aluminium Smelter

    Directory of Open Access Journals (Sweden)

    E. D. Wannaz

    2012-01-01

    Full Text Available A pollution gradient was observed in tree foliage sampled in the vicinity of a large aluminium production facility in Patagonia (Argentina. Leaves of Eucalyptus rostrata, and Populus hybridus and different needle ages of Pinus spec. were collected and concentrations of aluminium (Al and sulphur (S as well as physiological parameters (chlorophyll and lipid oxidation products were analyzed. Al and S concentrations indicate a steep pollution gradient in the study showing a relationship with the physiological parameters in particular membrane lipid oxidation products. The present study confirms that aluminium smelting results in high Al and sulphur deposition in the study area, and therefore further studies should be carried out taking into account potentially adverse effects of these compounds on human and ecosystem health.

  8. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (paluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium.

  9. Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process

    Science.gov (United States)

    Asmara, Y. P.; Siregar, J. P.; Tezara, C.; Ann, Chang Tai

    2016-02-01

    Aluminium is one of the preferred materials to be used as sacrificial anode for carbon steel protection. The efficiency of these can be low due to the formation of oxide layer which passivate the anodes. Currently, to improve its efficiency, there are efforts using a new technique called surface modifications. The objective of this research is to study corrosion mechanism of aluminium sacrificial anode which has been processed by cold work. The cold works are applied by reducing the thickness of aluminium sacrificial anodes at 20% and 40% of thickness reduction. The cathodic protection experiments were performed by immersion of aluminium connected to carbon steel cylinder in 3% NaCl solutions. Visual inspections using SEM had been conducted during the experiments and corrosion rate data were taken in every week for 8 weeks of immersion time. Corrosion rate data were measured using weight loss and linear polarization technique (LPR). From the results, it is observed that cold worked aluminium sacrificial anode have a better corrosion performance. It shows higher corrosion rate and lower corrosion potential. The anodes also provided a long functional for sacrificial anode before it stop working. From SEM investigation, it is shown that cold works have changed the microstructure of anodes which is suspected in increasing corrosion rate and cause de-passivate of the surface anodes.

  10. Neuroprotective effect of Allium cepa L. in aluminium chloride induced neurotoxicity.

    Science.gov (United States)

    Singh, Tanveer; Goel, Rajesh Kumar

    2015-07-01

    The present study was envisaged to investigate the neuroprotective potential of Allium cepa (A. cepa) in aluminium chloride induced neurotoxicity. Aluminium chloride (50 mg/kg/day) was administered orally in mice supplemented with different doses of A. cepa hydroethanolic extract for a period of 60 days. Various behavioural, biochemical and histopathological parameters were estimated in aluminium exposed animals. Chronic aluminium administration resulted in significant motor incoordination and memory deficits, which were also endorsed biochemically as there was increased oxidative stress as well as elevated acetylcholinesterase (AChE) and aluminium levels in the brain. Supplementation with A. cepa in aluminium exposed animals significantly improved muscle coordination and memory deficits as well as reduced oxidative stress, AChE and decreased abnormal aluminium deposition in the brain. Histopathologically, there was marked deterioration visualized as decreased vacuolated cytoplasm as well as decreased pyramidal cells in the hippocampal area of mice brain which were found to be reversed with A. cepa supplementation. Administration of BADGE (PPARγ antagonist) in aluminium exposed animals reversed the neuroprotective potential of A. cepa as assessed with various behavioural, biochemical, neurochemical and histopathological estimations. In conclusion, finding of this study suggested significant neuroprotective potential of A. cepa in aluminium induced neurotoxicity. Further, the role of PPARγ receptor agonism has also been suggested as a putative neuroprotective mechanism of A. cepa, which needs further studies for confirmation.

  11. PREPARATION OF ALUMINIUM OXIDE CERAMIC-CURVED PIPE BY SLIP CASTING%注浆成型法制备氧化铝陶瓷弯管

    Institute of Scientific and Technical Information of China (English)

    伍协; 陈振华; 李富营

    2011-01-01

    以氧化铝为主要原料,采用注浆成型法制备氧化铝陶瓷弯管。论文比较详细地研究了pH值、颗粒级配和有机粘结剂对产品性能的影响。结果表明:当pH值为1,粘结剂为2wt%获得的泥浆粘度最小;用颗粒大小4μm的100%α-Al2O3细粉制备的氧化铝陶瓷弯管气孔率最小、表观密度最大、显微结构最理想。%Based on aluminium oxide as main raw material, aluminium oxide ceramic-curved pipe was prepared by slip casting, pH, particle grading and binder were reshearched on the performance of aluminium oxide ceramic-curved pipe in detail.The results showed that. When the pH is 1 and binder is 2wt%, the viscosity of mud is smallest. The particle grading is 4 μ m 100% a-Al2O3 powder which porosity is the smallest, apparent density is the biggest, the microstructure is the most ideal.

  12. Enhanced electrical and optical properties of room temperature deposited Aluminium doped Zinc Oxide (AZO) thin films by excimer laser annealing

    Science.gov (United States)

    El hamali, S. O.; Cranton, W. M.; Kalfagiannis, N.; Hou, X.; Ranson, R.; Koutsogeorgis, D. C.

    2016-05-01

    High quality transparent conductive oxides (TCOs) often require a high thermal budget fabrication process. In this study, Excimer Laser Annealing (ELA) at a wavelength of 248 nm has been explored as a processing mechanism to facilitate low thermal budget fabrication of high quality aluminium doped zinc oxide (AZO) thin films. 180 nm thick AZO films were prepared by radio frequency magnetron sputtering at room temperature on fused silica substrates. The effects of the applied RF power and the sputtering pressure on the outcome of ELA at different laser energy densities and number of pulses have been investigated. AZO films deposited with no intentional heating at 180 W, and at 2 mTorr of 0.2% oxygen in argon were selected as the optimum as-deposited films in this work, with a resistivity of 1×10-3 Ω.cm, and an average visible transmission of 85%. ELA was found to result in noticeably reduced resistivity of 5×10-4 Ω.cm, and enhancing the average visible transmission to 90% when AZO is processed with 5 pulses at 125 mJ/cm2. Therefore, the combination of RF magnetron sputtering and ELA, both low thermal budget and scalable techniques, can provide a viable fabrication route of high quality AZO films for use as transparent electrodes.

  13. Effect of aluminium phosphate as admixture on oxychloride cement

    Indian Academy of Sciences (India)

    M P S Chandrawat; R N Yadav

    2000-02-01

    The effect of admixing of aluminium phosphate on oxychloride cement in the matrix has been investigated. It is shown that aluminium phosphate retards the setting process of the cement and improves water-tightness.

  14. Structural colours and applications to anodised aluminium surfaces

    DEFF Research Database (Denmark)

    Johansen, Villads Egede

    This thesis investigates possible ways of creating aluminium with a milky white, metallic appearance for decorative purposes. Since white cannot be obtained through traditional absorption based dyeing of aluminium, optical mechanisms based on scattering by nanostructures are studied in order...

  15. Solidification of spent TBP solvent with aluminium chloride compounds

    International Nuclear Information System (INIS)

    The new techniques for processing spent TBP was investigated. It was proved that treatment of TBP containing DBP with aluminium chloride resulted in the formation of aluminium phosphate suitable for long term storage and final disposal

  16. Determination of ultratrace amounts of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization/ICP-MS

    International Nuclear Information System (INIS)

    A method has been developed for determining the 0.01 ng g-1 level of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization (ETV)/ICP-MS. This method was found to be significantly interfered with any matrices or other elements contained. An ion-exchange technique was therefore applied to separate uranium and thorium from aluminium and other elements. It was known that uranium are adsorbed on an anion-exchange resin and thorium are adsorbed on cation-exchange resin. However, aluminium and copper were eluted with 6 M hydrochloric acid. Dissolve the sample with hydrochloric acid containing copper which was added for analysis of pure aluminium, and oxidize with hydrogen peroxide. Concentration of hydrochloric acid in the solution was adjusted to 6 M, and then passed the solution through the mixed ion-exchange resin column. After the uranium and thorium were eluted with 1 M hydrofluoric acid-0.1 M hydrochloric acid, the solution was evaporated to dryness. It was then dissolved with 1 M hydrochloric acid. Uranium and thorium were analyzed by ETV/ICP-MS using tungsten and molybdenum boats, respectively, since the tungsten boat contained high-level thorium and the molybdenum boat contained uranium. The determination limit of uranium and thorium were 0.003 and 0.005 ng g-1, respectively. (author)

  17. Characterisation of Ga-coated and Ga-brazed aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Ferchaud, E. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Christien, F., E-mail: frederic.christien@univ-nantes.fr [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Barnier, V. [Ecole Nationale Superieure des Mines, MPI, CNRS UMR5146, Centre SMS, 158 Cours Fauriel, 42023 Saint Etienne (France); Paillard, P. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France)

    2012-05-15

    This work is devoted to the brazing of aluminium using liquid gallium. Gallium was deposited on aluminium samples at {approx} 50 Degree-Sign C using a liquid gallium 'polishing' technique. Brazing was undertaken for 30 min at 500 Degree-Sign C in air. EDS (Energy Dispersive X-ray Spectroscopy) and AES (Auger Electron Spectroscopy) characterisation of Ga-coated samples has shown that the Ga surface layer thickness is of ten (or a few tens of) nanometres. Furthermore, aluminium oxide layer (Al{sub 2}O{sub 3}) was shown to be 'descaled' during Ga deposition, which ensures good conditions for further brazing. Cross-section examination of Ga-coated samples shows that liquid gallium penetrates into the aluminium grain boundaries during deposition. The thickness of the grain boundary gallium film was measured using an original EDS technique and is found to be of a few tens of nanometres. The depth of gallium grain boundary penetration is about 300 {mu}m at the deposition temperature. The fracture stress of the brazed joints was measured from tensile tests and was determined to be 33 MPa. Cross-section examination of brazed joints shows that gallium has fully dissolved into the bulk and that the joint is really autogenous. - Highlights: Black-Right-Pointing-Pointer Aluminium can be brazed using liquid gallium deposited by a 'polishing' technique. Black-Right-Pointing-Pointer The aluminium oxide layer is 'descaled' during liquid Ga 'polishing' deposition. Black-Right-Pointing-Pointer EDS can be used for determination of surface and grain boundary Ga film thickness. Black-Right-Pointing-Pointer The surface and grain boundary Ga film thickness is of a few tens of nm. Black-Right-Pointing-Pointer Surface and grain boundary gallium dissolves in the bulk during brazing.

  18. Friction stir welding (FSW) of aluminium foam sandwich panels

    OpenAIRE

    M. Bušić; Kožuh, Z.; D. Klobčar; Samardžić, I.

    2016-01-01

    The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and f...

  19. Aluminium allergy and granulomas induced by vaccinations for children

    DEFF Research Database (Denmark)

    Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

    2014-01-01

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

  20. Stability of aluminium beams in case of fire

    NARCIS (Netherlands)

    Meulen, O.R. van der; Soetens, F.; Maljaars, J.

    2014-01-01

    Fire is often the dominant design criterion for aluminium structures. Present design rules for aluminium constructions in fire neglect both the decrease in susceptibility to local buckling and the effects of creep, that are intrinsic to aluminium. They may therefore either overestimate or underestim

  1. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  2. Qimingxing Aluminium of Jinma Group Ceases Production

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>Jinma Group announced on December 23 that its subsidiary Meishan Qimingxing Aluminium decided to cease production starting from De- cember 23,and that the company will keep a close eye to the market and will resume pro- duction once the market bounces back.In 2007, Jinma Group took over Meishan Qimingxing’s 40% share by 112 million yuan to enter the aluminium industry.Meishan Qimingxing’s assets include a 125,000-ton production line of aluminium and 168 300KA electrolytic baths. Affected by the state’s macro-regulation policy in early years,the company’s profit fell short of estimates.Net profit of Meishan Qimingxing in 2007 was 10.65 million yuan.

  3. Comparative study of highly dense aluminium- and gallium-doped zinc oxide transparent conducting sol–gel thin films

    Indian Academy of Sciences (India)

    Naji Al Dahoudi

    2014-10-01

    Transparent conducting aluminium- and gallium-doped zinc oxide (AZO and GZO) layers have been deposited by spin coating on glass substrates. The coatings have been sintered in air at 450 °C for 30 min and then post-annealed at 350 °C in a reducing atmosphere for 30 min. The electrical, optical and morphological properties of both coatings have been studied and compared. The conventional sols lead to very thin coating, typically 24 nm for a single layer of AZO and 32 nm of GZO with electrical resistivity of 0.72 and 0.35 cm, respectively. The value however, drastically decreases down to a minimum of 2.6 × 10-2 cm for AZO and 1.76 × 10-2 cm for GZO, when five multilayer coatings are made. The origin of these differences is due to the different morphology of the coatings showing different electron scattering process. The GZO sol leads to denser smoother structure (porosity of 5%) layers with an average roughness of 2.76 Å, while the AZO coating is formed by a more porous assembly (porosity of 20%) with an average roughness of 3.46 Å. Both coatings exhibit high transparency ( > 85%) in the visible spectrum range with a slight shift of the absorption energy gap.

  4. A Macroporous TiO2 Oxygen Sensor Fabricated Using Anodic Aluminium Oxide as an Etching Mask

    Directory of Open Access Journals (Sweden)

    Sheng-Po Wu

    2010-01-01

    Full Text Available An innovative fabrication method to produce a macroporous Si surface by employing an anodic aluminium oxide (AAO nanopore array layer as an etching template is presented. Combining AAO with a reactive ion etching (RIE processes, a homogeneous and macroporous silicon surface can be effectively configured by modulating AAO process parameters and alumina film thickness, thus hopefully replacing conventional photolithography and electrochemical etch methods. The hybrid process integration is considered fully CMOS compatible thanks to the low-temperature AAO and CMOS processes. The gas-sensing characteristics of 50 nm TiO2 nanofilms deposited on the macroporous surface are compared with those of conventional plain (or non-porous nanofilms to verify reduced response noise and improved sensitivity as a result of their macroporosity. Our experimental results reveal that macroporous geometry of the TiO2 chemoresistive gas sensor demonstrates 2-fold higher (~33% improved sensitivity than a non-porous sensor at different levels of oxygen exposure. In addition, the macroporous device exhibits excellent discrimination capability and significantly lessened response noise at 500 °C. Experimental results indicate that the hybrid process of such miniature and macroporous devices are compatible as well as applicable to integrated next generation bio-chemical sensors.

  5. Development of electrostatic supercapacitors by atomic layer deposition on nanoporous anodic aluminium oxides for energy harvesting applications

    Directory of Open Access Journals (Sweden)

    Lucia eIglesias

    2015-03-01

    Full Text Available Nanomaterials can provide innovative solutions for solving the usual energy harvesting and storage drawbacks that take place in conventional energy storage devices based on batteries or electrolytic capacitors, because they are not fully capable for attending the fast energy demands and high power densities required in many of present applications. Here, we report on the development and characterization of novel electrostatic supercapacitors made by conformal Atomic Layer Deposition on the high open surface of nanoporous anodic alumina membranes employed as templates. The structure of the designed electrostatic supercapacitor prototype consists of successive layers of Aluminium doped Zinc Oxide, as the bottom and top electrodes, together Al2O3 as the intermediate dielectric layer. The conformality of the deposited conductive and dielectric layers, together with their composition and crystalline structure have been checked by XRD and electron microscopy techniques. Impedance measurements performed for the optimized electrostatic supercapacitor device give a high capacitance value of 200 µF/cm2 at the frequency of 40 Hz, which confirms the theoretical estimations for such kind of prototypes, and the leakage current reaches values around of 1.8 mA/cm2 at 1 V. The high capacitance value achieved by the supercapacitor prototype together its small size turns these devices in outstanding candidates for using in energy harvesting and storage applications.

  6. Diamond grooving of rapidly solidified optical aluminium

    Science.gov (United States)

    Abou-El-Hossein, Khaled; Hsu, Wei-Yao; Ghobashy, Sameh; Cheng, Yuan-Chieh; Mkoko, Zwelinzima

    2015-10-01

    Traditional optical aluminium grades such as Al 6061 are intensively used for making optical components for applications ranging from mould insert fabrication to laser machine making. However, because of their irregular microstructure and relative inhomogeneity of material properties at micro scale, traditional optical aluminium may exhibit some difficulties when ultra-high precision diamond turned. Inhomogeneity and micro-variation in the material properties combined with uneven and coarse microstructure may cause unacceptable surface finish and accelerated tool wear, especially in grooving operation when the diamond tool edge is fully immersed in the material surface. Recently, new grades of optical aluminium that are featured by their ultra-fine microstructure and improved material properties have been developed to overcome the problem of high tool wear rates. The new aluminium grades have been developed using rapid solidification process which results in extremely small grain sizes combined with improved mechanical properties. The current study is concerned with investigating the performance of single-point diamond turning when grooving two grades of rapidly solidified aluminium (RSA) grades: RSA905 which is a high-alloyed aluminium grade and RSA443 which has a high silicon content. In this study, two series of experiments employed to create radial microgrooves on the two RSA grades. The surface roughness obtained on the groove surface is measured when different combinations of cutting parameters are used. Cutting speed is varied while feed rate and depth of cut were kept constant. The results show that groove surface roughness produced on RSA443 is higher than that obtained on RSA905. Also, the paper reports on the effect of cutting speed on surface roughness for each RSA grade.

  7. The role of magnesium in the electrochemical behaviour of 5XXX aluminium-magnesium alloys

    NARCIS (Netherlands)

    Flores Ramirez, J.R.

    2006-01-01

    An investigation concerning the effects of magnesium on the intergranular corrosion susceptibility of AA5XXX aluminium alloys was carried out. In the present work, magnesium is found to be highly mobile in the bulk metal as well as in the aluminium oxide. This mobility is also found to be dependent

  8. Microstructure and interfaces of a reaction coating on aluminium alloys by laser processing

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1993-01-01

    This paper reports an approach to coat a ceramic layer on aluminium alloys by means of chemical reaction. The reaction product of Al2O3 layer of 100 µm in thickness has been formed using a powder mixture of silicon oxide and aluminium by laser processing. It turns out that the large amount of heat f

  9. New aluminium alloys with high lithium content

    Energy Technology Data Exchange (ETDEWEB)

    Schemme, K.; Velten, B.

    1989-06-01

    Since the early 80's there have been made great efforts to replace the high strength aluminium alloys for the aircraft and space industry by a new generation of aluminium-lithium alloys. The attractivity of this kind of alloys could be increased by a further reduction of their density, caused by an increasing lithium content (/ge/ 5 wt.% Li). Therefore binary high-lithium containing alloys with low density are produced and metallografically investigated. A survey of their strength and wear behavior is given by using tensile tests and pin abrasing tests. (orig.).

  10. Hysteretic Process of Aluminium Oxide Films Deposited by Reactive Sputtering Method%磁控溅射沉积氧化铝薄膜的迟滞效应

    Institute of Scientific and Technical Information of China (English)

    徐化冰; 徐香坤

    2013-01-01

    The hysteretic behaviour of aluminium oxide films in reactive sputtering was investigated by plasma optical emission spectroscopy technology. The evolutions of aluminium( 396 nm) and aluminium oxide(484 nm) emission lines as functions of oxygen flow rates were measured. The crystal structure, a-tomic ratio and light transmission of aluminium oxide films were analyzed by X-ray diffraction (XRD) , energy dispersive spectrometer (EDS) and ultraviolet - visible spectroscopy (UV-VIS). The results show that because the aluminium oxide deposited on the magnetron target impacts the alumina sputtering, the Al (39 6 nm) line intensity affects the crystal structure, atomic ratio and light transmission of aluminium oxide films. Meanwhile, the hysteresis curves show that an optimum deposition zone exists in the transition region where the oxygen flow rates is 1. 5~2. 0 mL/min. The sample obtains in this deposition zone' and its composition has the best chemical atomic weight ratio of 0. 689. This indicates that the deposited aluminium oxide films have excellent qualities.%利用光发射谱(OES)技术,对反应磁控溅射过程的氧化铝薄膜的迟滞效应进行了研究.对等离子体中的铝(396 nm)谱线和氧化铝(484 nm)谱线随氧气流量的变化进行了实时测量,获得了其迟滞曲线.在迟滞曲线的不同位置分别进行了氧化铝薄膜的沉积试验.采用X射线衍射仪(XRD)、能谱仪(EDS)和紫外可见吸收光谱仪(UV-VIS)对薄膜的晶体结构、成分和透光性进行了分析.结果表明:由于磁控靶表面的氧化铝沉积影响了铝靶材的溅射,导致Al(396 nm)谱线的强度对氧化铝薄膜的晶体结构、原子比以及样品的透光性有明显的影响.同时,由迟滞曲线可知在氧气流量为1.5~2.0 mL/min的过渡区内存在着一个最优沉积带.在这个沉积带获得的样品,其成分具有最佳的化学原子量配比,为0.689.这说明沉积出了高质量的氧化铝薄膜.

  11. China’s Aluminium Consumption and the Related Policies

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>China is a major aluminium consumer country in the world. In 2005, China produced 7.81 million tons aluminium and imported 640,000 tons. Meanwhile, China also exported 1.32 million tons aluminium in 2005. China’s apparent consumption of aluminium in 2005 was about 7.1 million tons, which was 9.3 times over that in 1990. China’s aluminium consumption growth has kept at an annual average of 16.1 per cent since 1990, which makes China the

  12. China’s Production and Market of Aluminium Extruded Profiles

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Chinese aluminium extrusion industry came into existence at the early 1950s with most products used in military industry and national defence.At the beginning of 1980s,the produc- tion of construction aluminium profiles started simultaneously in North and South China.In the following thirty years,the aluminium extru- sion industry entered into a quickly developing stage with a focus on construction aluminium profiles.With the blooming real estate industry, the demand for construction aluminium profiles from the domestic market has a tendency of yearly increase.From 2000,the quick devel- opments of China’s auto and railway vehicle

  13. Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.;

    1968-01-01

    Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produces...... rows of dislocation loops all lying parallel to one particular direction. If the aluminium target is quenched from 600 °C and annealed at room temperature prior to irradiation with aluminium ions, the rows of loops are suppressed. The amount of damage observed is considerably less than would...

  14. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    OpenAIRE

    B. Formanek; J. Piątkowski; J. Szymszal

    2010-01-01

    Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameter...

  15. Molecular breeding of cereals for aluminium resistance

    Science.gov (United States)

    Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

  16. Experimental analysis of cut welding in aluminium

    DEFF Research Database (Denmark)

    Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

    1993-01-01

    Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...

  17. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P;

    2005-01-01

    in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...

  18. Indentation of aluminium foam at low velocity

    Directory of Open Access Journals (Sweden)

    Shi Xiaopeng

    2015-01-01

    Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

  19. Microstructure Development during Solidification of Aluminium Alloys

    NARCIS (Netherlands)

    Ruvalcaba Jimenez, D.G.

    2009-01-01

    This Thesis demonstrates studies on microstructure development during the solidification of aluminium alloys. New insights of structure development are presented here. Experimental techniques such as quenching and in-situ High-brilliance X-ray microscopy were utilized to study the microstructure evo

  20. Computational prediction of the refinement of oxide agglomerates in a physical conditioning process for molten aluminium alloy

    Science.gov (United States)

    Tong, M.; Jagarlapudi, S. C.; Patel, J. B.; Stone, I. C.; Fan, Z.; Browne, D. J.

    2015-06-01

    Physically conditioning molten scrap aluminium alloys using high shear processing (HSP) was recently found to be a promising technology for purification of contaminated alloys. HSP refines the solid oxide agglomerates in molten alloys, so that they can act as sites for the nucleation of Fe-rich intermetallic phases which can subsequently be removed by the downstream de-drossing process. In this paper, a computational modelling for predicting the evolution of size of oxide clusters during HSP is presented. We used CFD to predict the macroscopic flow features of the melt, and the resultant field predictions of temperature and melt shear rate were transferred to a population balance model (PBM) as its key inputs. The PBM is a macroscopic model that formulates the microscopic agglomeration and breakage of a population of a dispersed phase. Although it has been widely used to study conventional deoxidation of liquid metal, this is the first time that PBM has been used to simulate the melt conditioning process within a rotor/stator HSP device. We employed a method which discretizes the continuous profile of size of the dispersed phase into a collection of discrete bins of size, to solve the governing population balance equation for the size of agglomerates. A finite volume method was used to solve the continuity equation, the energy equation and the momentum equation. The overall computation was implemented mainly using the FLUENT module of ANSYS. The simulations showed that there is a relatively high melt shear rate between the stator and sweeping tips of the rotor blades. This high shear rate leads directly to significant fragmentation of the initially large oxide aggregates. Because the process of agglomeration is significantly slower than the breakage processes at the beginning of HSP, the mean size of oxide clusters decreases very rapidly. As the process of agglomeration gradually balances the process of breakage, the mean size of oxide clusters converges to a

  1. Development and characterization of ultra-thin dosemeters of aluminium oxide; Desarrollo y caracterizacion de dosimetros ultra-delgados de oxido de aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Villagran V, E

    2003-07-01

    The aim of the present thesis work has been to investigate the thermoluminescent (Tl) response of aluminium oxide thin films with thicknesses of the order of 300 nm prepared by laser ablation. Aluminium oxide thin films show Tl response after they are subject to ultraviolet, beta and gamma radiation. The Tl curves exhibit peaks around 75 C and 169 C for UV radiation, 112 C and 180 C for beta particles and 110 C and 176 C for gamma radiation. In order to improve the Tl response some growth parameters such as power density and distance target-substrate were varied. The relation dose-response shows a non-linear behavior for UV irradiation; a linear behavior for beta-particles dose from 150 mGy to 50 Gy, and a linear behavior for gamma radiation dose from 5 Gy to 100 Gy. The kinetic Tl parameters were determined by Computerized Glow Curve Deconvolution (CGCD) method as well as using analytical methods. The CGCD results show that the high temperature peak is composed by four peaks with maximums in 165.7, 188.1, 215.3, 246.5 C. These obey a second order kinetics. The trap depth (E) values are 1.4, 1.6, 1.8 and 2.0 eV respectively. The different analytical results show a trap depth values of 0.914, 0.82 and 0.656 eV respectively. Oxide aluminium thin films obtained would be a suitable tool owing to their potential applications in clinical dosimetry, in the dose distributions due to weekly penetrating radiation determination, and in interfaces dosimetry. (Author)

  2. Structure and tensile/wear properties of microarc oxidation ceramic coatings on aluminium alloy

    Institute of Scientific and Technical Information of China (English)

    魏同波; 阎逢元; 刘维民; 田军

    2004-01-01

    Thick and hard ceramic coatings were prepared on the Al-Cu-Mg alloy by microarc oxidation in alkali-silicate electrolytic solution. The thickness and microhardness of the oxide coatings were measured. The influence of current density on the growth rate of the coating was examined. The microstructure and phase composition of the coatings were investigated by means of scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction. Moreover, the tensile strength of the Al alloy before and after microarc oxidation treatment were tested,and the fractography and morphology of the oxide coatings were observed using scanning electron microscope. It is found that the current density considerably influences the growth rate of the microarc oxidation coatings. The oxide coating is mainly composed of α-Al2 O3 and γ-Al2 O3, while high content of Si is observed in the superficial layer of the coating. The cross-section microhardness of 120 μm thick coating reaches the maximum at distance of 35 μm from the substrate/coating interface. The tensile strength and elongation of the coated Al alloy significantly decrease with increasing coating thickness. The microarc oxidation coatings greatly improve the wear resistance of Al alloy,but have high friction coefficient which changes in the range of 0.7 - 0.8. Under grease lubricating, friction coefficient is only 0.15 and wear loss is less than 1/10 of the loss under dry friction.

  3. First wall design of aluminium alloy R-tokamak

    International Nuclear Information System (INIS)

    A design study of a low-activation D-T tokamak Reacting Plasma Project In Nagoya has been finished. The study emphasizes the vacuum vessel and the bumper limiter. Our choice of materials (aluminium vacuum vessel, copper conductors, aluminium TF coil case and lead shield) results in a radiation level of about 1 x 10-3 times that of a TFTR type design, and 1 x 10-4 times that of JET type design, at 2 weeks after one D-T shot. Thick graphite tiles will be fixed directly on the aluminium vacuum vessel using aluminium spring washers and bolts. With this simplified structure of the bumper limiter, the inner surface temperature of the thick aluminium vacuum vessel will be less than 1200C which is required to reduce the overaging effect of the aluminium alloy. (orig.)

  4. What is the risk of aluminium as a neurotoxin?

    Science.gov (United States)

    Exley, Christopher

    2014-06-01

    Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

  5. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention.

  6. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as permeability were observed for any of the three diatoms suggesting that mechanisms of aluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. PMID:26921729

  7. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. PMID:25687835

  8. Straggling of heavy ions in aluminium

    International Nuclear Information System (INIS)

    An effort has been made to determine the straggling in aluminium of 4He, 16O and 35Cl ions of different energies produced by the tandem Van de Graaff at Harwell. The technique consists of scattering the accelerated and collimated ions in a scattering chamber from a 0.100 mg/cm2 gold foil, allowing the scattered ions to pass through a two aperture collimator, using different aluminium foils over one of the apertures and stopping the two emergent beams in a good quality silicon surface barrier detector the output of which is connected to a 4096 channel analyser. The energy widths obtained in the case of helium ions are in fair agreement with both the Bloch and the recent Tschalar (1968) theory. The measured widths in the case of heavy ions are very large and can be explained only if account is taken of their charge distributions in foils. This study should be useful in ion implantation work. (author)

  9. China will Reduce Aluminium Export in 2005

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>Starting from January 1, 2005, China eliminated the 8 per cent export tax rebate for aluminium, and further more, the exporters will have to pay 5 per cent export tax. This is beyond the expectations of the producers, for most of them thought only the 8 per cent export tax rebate would be eliminated and it was still too early to add the export tax.

  10. FSW characterization of 6082 aluminium alloys sheets

    OpenAIRE

    K. Mroczka; A. Pietras

    2009-01-01

    Purpose: The purpose of the investigations was to elaborate a set of FSW parameters for connecting 6082 aluminium alloy sheets allowing to produce welds of highest strength.Design/methodology/approach: The FSW was tried at different speeds and at additional cooling. The welds microstructure was studied using optical and scanning electron microscopes. The mechanical properties of produced connections are discussed regarding their tensile test and microhardness measurements.Findings: The FSW we...

  11. Methods of inoculation of pure aluminium structure

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2008-03-01

    Full Text Available Purpose: The main aim of investigations was the reduction of grain size and unification of structure for pure Al casting by introduction of small amount of inoculant (less than obligatory standart PN-EN 573-3, which concerning about aluminium purity, with electromagnetic field and variable casting parameters.Design/methodology/approach: To investigations it was used light microscopy and TEM. Surfaces of samples which were prepared for macro- and microstructure analysis were etched with use of solution of: 50g Cu, 400ml HCl, 300ml HNO3 and 300ml H2O. Thin foils for TEM investigations were electropolished with use of 20 ml HClO4 and 80ml CH3OH.Findings: The results of investigations and their analysis show possibility of effective inoculation of pure aluminium structure by use of some factors such as: different materials of the mould, influencing of stirring electromagnetic field into metal during solidification, inoculation by introducing AlTi5B1 inoculant into liquid aluminium and changing the pouring temperature.Research limitations/implications: I further research, authors of this paper are going to application of introduced method of inoculation in industrial tests.Practical implications: The work presents refinement of structure method which are particularly important in continuous and semi – continuous casting where products are used for plastic forming. Large columnar crystals zone result in forces extrusion rate reduction and during the ingot rolling delamination of external layers can occur. Thus, in some cases ingot skinning is needed, which rises the production costs.Originality/value: Contributes to research on size reduction in pure aluminium structure.

  12. Aluminium matrix composites fabricated by infiltration method

    OpenAIRE

    L.A. Dobrzański; M. Kremzer; A. J. Nowak; Nagel, A.

    2009-01-01

    Purpose: The aim of this work is to examine the structure and properties of metal matrix composites obtained by infiltration method of porous ceramic preforms by liquid aluminium alloy.Design/methodology/approach: Ceramic preforms were manufactured by the sintering method of ceramic powder. The preform material consists of powder Condea Al2O3 CL 2500, however, as the pore forming the carbon fibers Sigrafil C10 M250 UNS were used. Then ceramic preforms were infiltrated with liquid eutectic EN ...

  13. Role of phytohormones in aluminium rhizotoxicity.

    Science.gov (United States)

    Kopittke, Peter M

    2016-10-01

    Elevated concentrations of soluble aluminium (Al) reduce root growth in acid soils, but much remains unknown regarding the toxicity of this Al as well as the mechanisms by which plants respond. This review examines changes in phytohormones in Al-stressed plants. Al often results in a rapid 'burst' of ethylene in root apical tissues within 15-30 min, with this regulating an increase in auxin. This production of ethylene and auxin seems to be a component of a plant-response to toxic Al, resulting in cell wall modification or regulation of organic acid release. There is also evidence of a role of auxin in the expression of Al toxicity itself, with Al decreasing basipetal transport of auxin, thereby potentially decreasing wall loosening as required for elongation. Increasingly, changes in abscisic acid in root apices also seem to be involved in plant-responses to toxic Al. Changes in cytokinins, gibberellins and jasmonates following exposure to Al are also examined, although little information is available. Finally, although not a phytohormone, concentrations of nitric oxide change rapidly in Al-exposed tissues. The information presented in this review will assist in focusing future research efforts in examining the importance of phytohormones in plant tissues exposed to toxic levels of Al. PMID:27352002

  14. Softening Behaviour of Selected Commercially Pure Aluminium Model Alloys

    OpenAIRE

    Sande, Gunnar

    2012-01-01

    A characterization of the softening behaviour of four different commercially pure aluminium alloys has been carried out. The work is related to the MOREAL project (Modelling towards value-added recycling friendly aluminium alloys), where the main goal is to quantify the effect of the elements in recyclable aluminium alloys on microstructure and mechanical properties during thermo-mechanical processing. Typical elements are iron (Fe), silicon (Si) and manganese (Mn), and the alloys studied in ...

  15. Un-optimistic Prospects for the Westward Movement of Aluminium

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>The westward movement of aluminium is essential for the industrial development.Up till now,the northwestern area has planned to construct more than 40 aluminium projects with a total production capacity of over 20 million tons.The future rate of progress of newly constructed projects are directly related to the supplies of the aluminium market,having critical guiding meaning for the trends of

  16. Friction factor of CP aluminium and aluminium–zinc alloys

    Indian Academy of Sciences (India)

    N Vidhya Sagar; K S Anand; A C Mithun; K Srinivasan

    2006-12-01

    Friction factor has been determined for CP aluminium and aluminium–zinc alloys using ring compression test at different temperatures from 303 K to 773 K. It is found that CP aluminium exhibits sticking whereas Al–Zn alloys do not exhibit sticking at elevated temperatures. Hot working of Al–Zn alloy is easier than that of CP aluminium at 773 K. As zinc content increases up to 10 wt% the friction factor decreases up to 0.02.

  17. Aluminium supplier selection for the automotive parts manufacturer

    OpenAIRE

    M. Cieśla

    2016-01-01

    This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method an...

  18. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    Directory of Open Access Journals (Sweden)

    B. Bobic

    2010-03-01

    Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

  19. Tribological characteristics of coatings on aluminium and its alloys

    OpenAIRE

    Abdul-Mahdi, Fadhil S

    1987-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. Hard anodising on aluminium and its alloys has been widely practised for many years in order to improve the resistance of the otherwise poor wear characteristics of aluminium. In recent years there has been an increasing interest in other treatments and coatings, on both aluminium and other base metals. The aim of this investigation is to explain the tribological performance and wear mechanis...

  20. Behaviour and design of aluminium alloy structural elements

    OpenAIRE

    Su, Meini; 蘇玫妮

    2014-01-01

    Aluminium alloys are nonlinear metallic materials with continuous stress-strain curves that are not well represented by the simplified elastic, perfectly plastic material model used in most existing design specifications. The aims of this study are to develop a more efficient design method for aluminium alloy structures by rationally exploiting strain hardening. The key components of this study include laboratory testing, numerical modelling and development of design guidance for aluminium al...

  1. Multiply-negatively charged aluminium clusters and fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Noelle

    2008-07-15

    Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

  2. Effect of Oxide Inclusions on Electrochemical Properties of Aluminium Sacrificial Anodes

    Institute of Scientific and Technical Information of China (English)

    M. Emamy; A. Keyvani; M. Mahta; J. Campbell

    2009-01-01

    Oxide films are incorporated into melts by an entrainment process, and are expected to be present in most metals, but particularly cast Al alloys. The oxides are necessarily present as folded-over double films (bifilms) that are effectively cracks. Their effect on the electrochemical behaviour of cast Al-5Zn-0.02ln sacrificial anodes was studied in 3 wt pct sodium chloride solution using the NACE efficiency evaluation. Three methods were employed to entrain progressive amounts of oxide in the alloy, including the addition of Al-Zn-ln maching chips to the charge, increasing the pouring height, and agitating the melt. The introduction of oxide bifilms in the cast alloy resulted in the deterioration of the electrochemical properties of the sacrificial anodes, such as current capacity and anode efficiency, and introduced increasing variability in these properties. The results suggest that corrosion behaviour is strongly related to the presence of bifilms suspended in the liquid alloy because bifilms provide crack paths allowing the corrodant to penetrate deeply into the metal matrix, and simultaneously provide localized galvanic cells because of the precipitation of Fe rich intermetallic compounds on their outer surfaces.

  3. Aluminium in the rail transportation market

    Energy Technology Data Exchange (ETDEWEB)

    Zehnder, J. [Alcan Alesa Engineering Ltd., Zurich (Switzerland). Alcan Mass Transportation Systems

    2002-07-01

    Rail-transportation is not, as one might expect, a homogeneous market but extremely fragmented and even with huge differences from continent to continent, i.e. in North America freight transport is dominating whereas in Europe passenger transport prevails. A first segmentation splits infrastructure from vehicles. In a second layer of segmentation we distinguish between light rail vehicles, heavy metros, regional trains, intercity trains, high speed trains with and without tilting, maglev trains, freight vehicles and locomotives. Finally, we find aluminium applications in wheels, suspension parts, brake equipment, traction equipment, body structure, hang on parts and interior trim. On the infrastructure side best use of aluminium is in the field of power supply. In order to have the best solution for each application, all forms of products such as castings, forgings, flat rolled products and extrusions are needed and the engineers are using a broad choice or different alloys for all the requirements such as structural strength, decorative aspect, electrical conductivity, wear resistance, weldability, corrosion resistance etc. Innovation cycles in rail transportation are very slow, mainly because the expected life of vehicles is over 30 years and so no fleet owner will run the risk of getting vehicles with non-proven components, i.e. where a safe life of over 30 years cannot be shown. In the following the most important aluminium applications are shown and discussed. (orig.)

  4. Plasmonic enhancement of photoluminescence from aluminium nitride

    Science.gov (United States)

    Flynn, Chris; Stewart, Matthew

    2016-03-01

    Aluminium nitride (AlN) films were grown on c-plane sapphire wafers by molecular beam epitaxy (MBE) under aluminium-rich conditions. The excess aluminium (Al) accumulated on the surface of the films as micro-scale droplets 1-10 μm in size, and as Al nanoparticles with diameters in the range 10-110 nm. Photoluminescence (PL) measurements were performed on the AlN samples using a 193 nm Excimer laser as the excitation source. Prior to PL measurements the wafers were cleaved in half. One half of each wafer was submitted to a 10 min treatment in H3PO4 heated to 70 °C to remove the excess Al from the film surface. The remaining half was left in the as-deposited condition. The mean intensities of the near-band-edge PL peaks of the as-deposited samples were 2.0-3.4 times higher compared to the samples subjected to the H3PO4 Al-removal treatment. This observation motivated calculations to determine the optimal Al surface nanosphere size for plasmonic enhancement of PL from AlN. The PL enhancement was found to peak for an Al nanosphere radius of 15 nm, which is within the range of the experimentally-observed Al nanoparticle sizes.

  5. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    Directory of Open Access Journals (Sweden)

    B. Formanek

    2010-10-01

    Full Text Available Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameters. The methods of light and scanning microscopy were used to reveal the structure of composite casting. Changes in chemical composition and phase composition of particles of the FeAl intermetallic phase in aluminium matrix were confirmed. The structure of silumin casting with matrix containing microregions of ceramic and intermetallic phases, typical of hybrid reinforcements, was obtained.

  6. Thermal formation of corundum from aluminium hydroxides prepared from various aluminium salts

    Indian Academy of Sciences (India)

    J Temuujin; Ts JADAMBAA; K J D Mackenzie; P Angerer; F Porte; F Riley

    2000-08-01

    Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived from the sulfate. This contains a higher concentration of anionic impurities related to differences in the solubility of the original aluminium salts. The sulfate is retained in the gel to higher temperatures at which its eventual decomposition may lead to the formation of a reactive pore structure which facilitates the nucleation of -Al2O3.

  7. Synthesis of aluminium nanoparticles by arc evaporation of an aluminium cathode surface

    Indian Academy of Sciences (India)

    M Gazanfari; M Karimzadeh; S Ghorbani; M R Sadeghi; G Azizi; H Karimi; N Fattahi; Z Karimzadeh

    2014-06-01

    Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on the nanoparticles was performed immediately. The effects of media on the yield and morphology of aluminium nanoparticles were investigated. Analysis result of the samples indicated that particle size was less than 30 nm, when 120 A/cm2 arc current was used. In addition, coating agent can affect arc velocity, arc stability, morphology and composition of the nanoparticles. Resultant nanoparticles were identified using X-ray powder diffraction (XRD), also their surface morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and finally the accuracy of coating was assessed with infrared (IR) spectroscopy.

  8. Effect of electrolyte temperature on the thickness of anodic aluminium oxide (AAO layer

    Directory of Open Access Journals (Sweden)

    P. Michal

    2016-07-01

    Full Text Available Effect of electrolyte temperature on the thickness of resulting oxide layer has been studied. Unlike previous published studies this article was aimed to monitor the relationship between electrolyte temperature and resulting AAO layer thickness in interaction with other input factors affecting during anodizing process under special process condition, i.e. lower concentration of sulphuric acid, oxalic acid, boric acid and sodium chloride. According to Design of Experiments (DOE 80 individual test runs of experiment were carried out. Using statistical analysis and artificial intelligence for evaluation, the computational model predicting the thickness of oxide layer in the range from 5 / μm to 15 / μm with tolerance ± 0,5 / μm was developed.

  9. Cold-impregnated aluminium. A new source of nickel exposure.

    Science.gov (United States)

    Lidén, C

    1994-07-01

    A new technique for finishing anodized aluminium was introduced during the 1980s--cold impregnation with nickel. Nickel is available on the surface of cold-impregnated aluminium, as shown by the dimethylglyoxime test. Chemical analysis with EDXA showed that nickel was in the form of NiSO4. A case of work-related allergic contact dermatitis in an engraver with nickel allergy is reported. It transpired that the patient was exposed to nickel in connection with aluminium. It is concluded that cold-impregnated aluminium is a new source of nickel exposure, probably previously unknown to dermatologists. PMID:7924288

  10. Effects of aluminium surface morphology and chemical modification on wettability

    Science.gov (United States)

    Rahimi, M.; Fojan, P.; Gurevich, L.; Afshari, A.

    2014-03-01

    Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie-Baxter to Wenzel regime upon changing the surface roughness was also observed.

  11. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  12. Aluminium anode for biogalvanic metal--oxygen -cells

    Energy Technology Data Exchange (ETDEWEB)

    Weidlich, E.

    1975-02-20

    The invention deals with an aluminium anode for biogalvanic metal--oxygen cells. The object of the invention is to improve further an aluminium anode for biogalvanic metal--oxygen cells. In particular, the lifetime is to be increased and the Faraday degree of efficiency is to be improved by suppressing an excessive hydrogen development. The anode is thus constructed so as to have a metal net on both sides with aluminium layers, and the surfaces of the aluminium layers not facing the metal net are lapped or sand-blasted and have an anodized layer on their boundary regions.

  13. Negative aluminium electrode for biogalvanic metal-oxygen cells

    Energy Technology Data Exchange (ETDEWEB)

    Weidlich, E.

    1977-03-24

    The invention deals with an aluminium anode for biogalvanic metal-oxygen cells. The object of the invention is to further improve an aluminium anode for biogalvanic metal-oxygen cells. In particular, the service life is to be increased and the Faraday degree of efficiency is to be improved, by suppressing an excessive hydrogen development. The anode is thus constructed so as to have a metal net on both sides with aluminium layers and the surfaces of the aluminium layers not facing the metal net are lapped or sand-blasted and have an eloxal layer on their boundary regions.

  14. The stability of aluminium oxide monolayer and its interface with two-dimensional materials.

    Science.gov (United States)

    Song, Ting Ting; Yang, Ming; Chai, Jian Wei; Callsen, Martin; Zhou, Jun; Yang, Tong; Zhang, Zheng; Pan, Ji Sheng; Chi, Dong Zhi; Feng, Yuan Ping; Wang, Shi Jie

    2016-01-01

    The miniaturization of future electronic devices requires the knowledge of interfacial properties between two-dimensional channel materials and high-κ dielectrics in the limit of one atomic layer thickness. In this report, by combining particle-swarm optimization method with first-principles calculations, we present a detailed study of structural, electronic, mechanical, and dielectric properties of Al2O3 monolayer. We predict that planar Al2O3 monolayer is globally stable with a direct band gap of 5.99 eV and thermal stability up to 1100 K. The stability of this high-κ oxide monolayer can be enhanced by substrates such as graphene, for which the interfacial interaction is found to be weak. The band offsets between the Al2O3 monolayer and graphene are large enough for electronic applications. Our results not only predict a stable high-κ oxide monolayer, but also improve the understanding of interfacial properties between a high-κ dielectric monolayer and two-dimensional material. PMID:27381580

  15. Preliminary results on TL and OSL aluminium oxide dosimeters developed at IPEN

    Energy Technology Data Exchange (ETDEWEB)

    Fukumori, David T.; Yoshito, Walter K.; Ussui, Valter; Lazar, Dolores R.R.; Campos, Leticia L., E-mail: fukumori@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The aluminum oxide composes the modern TL and OSL radiation dosimeters. TL and OSL phenomena are related to chemical elements in the crystalline structure of {alpha}-Al{sub 2}O{sub 3}. The aim of this work was to develop materials based on aluminum oxide for use in TL and OSL dosimetry. The studies included the dosimetric properties of alumina samples obtained by electro fusion, adsorption and coprecipitation. Electro fused alumina commercially available as abrasive particles was used to produce the pellets by glass sintering. Adsorption and coprecipitation were the methods used to insert metal ions to alumina. The best results were achieved with electro fused alumina and Tm{sup 3+} doped Al{sub 2}O{sub 3} pellets. The electro fused alumina-glass pellets show TL and OSL signals and the TL curve has two peaks. Its minimum detectable radiation dose is 7.2 mGy and the linearity of TL response as function of dose is up to about 800 mGy. The {alpha}-Al{sub 2}O{sub 3}:Tm pellets produced by sintering at 1550 deg C presented a meaningful TL glow curve so that it is worth studying their properties and viability of use in dosimetry. (author)

  16. The stability of aluminium oxide monolayer and its interface with two-dimensional materials

    Science.gov (United States)

    Song, Ting Ting; Yang, Ming; Chai, Jian Wei; Callsen, Martin; Zhou, Jun; Yang, Tong; Zhang, Zheng; Pan, Ji Sheng; Chi, Dong Zhi; Feng, Yuan Ping; Wang, Shi Jie

    2016-07-01

    The miniaturization of future electronic devices requires the knowledge of interfacial properties between two-dimensional channel materials and high-κ dielectrics in the limit of one atomic layer thickness. In this report, by combining particle-swarm optimization method with first-principles calculations, we present a detailed study of structural, electronic, mechanical, and dielectric properties of Al2O3 monolayer. We predict that planar Al2O3 monolayer is globally stable with a direct band gap of 5.99 eV and thermal stability up to 1100 K. The stability of this high-κ oxide monolayer can be enhanced by substrates such as graphene, for which the interfacial interaction is found to be weak. The band offsets between the Al2O3 monolayer and graphene are large enough for electronic applications. Our results not only predict a stable high-κ oxide monolayer, but also improve the understanding of interfacial properties between a high-κ dielectric monolayer and two-dimensional material.

  17. Cobalt and Nickel Nanopillars on Aluminium Substrates by Direct Current Electrodeposition Process

    Directory of Open Access Journals (Sweden)

    Santos A

    2009-01-01

    Full Text Available Abstract A fast and cost-effective technique is applied for fabricating cobalt and nickel nanopillars on aluminium substrates. By applying an electrochemical process, the aluminium oxide barrier layer is removed from the pore bottom tips of nanoporous anodic alumina templates. So, cobalt and nickel nanopillars are fabricated into these templates by DC electrodeposition. The resulting nanostructure remains on the aluminium substrate. In this way, this method could be used to fabricate a wide range of nanostructures which could be integrated in new nanodevices.

  18. Potentiostatic Electrochemical Preparation and Characterisation of Aluminium Containing Nickel Selenide

    Directory of Open Access Journals (Sweden)

    Sandeep Gohar

    2014-01-01

    Full Text Available The wide range of properties exhibited by Al based alloy makes them suitable for different applications. Aluminium containing nickel Selenide ternary alloy possess considerable corrosion resistance as compared to their pure metal counterparts. The objective of the present work has been focused on the preparation and characterisation of its thin film. Alloying with Aluminium improve the oxidation resistance and increases the heat conductivity of the alloy. There is always a high demand for plating Al and its alloys in automotive and aerospace products, house-hold goods, and artificial jewellery etc,. The morphological and the structural studies of the electrodeposited thin film were determined by Scanning Electron Microscope (SEM images and X-Ray Diffraction Pattern (XRD while elemental composition has been done by Energy Dispersive X-Ray Spectroscopy (EDAX analysis.

  19. Spectroscopic study of plasma during electrolytic oxidation of magnesium- and aluminium-alloy

    Science.gov (United States)

    Jovović, J.; Stojadinović, S.; Šišović, N. M.; Konjević, N.

    2012-10-01

    We present the results of an optical emission spectroscopy study of Plasma during Electrolytic Oxidation (PEO) of magnesium- and aluminum-alloy. Plasma electron number density Ne diagnostics is performed either from the Hβ line shape or from the width or shift of non-hydrogenic ion lines of aluminum and magnesium. The line profile analysis of the Hβ suggests presence of two PEO processes characterized by relatively low electron number densities Ne≈1.2×1015 cm-3 and Ne≈2.3×1016 cm-3. Apart from these two low Ne processes, there is the third one related to the ejection of evaporated anode material through micro-discharge channels. This process is characterized by larger electron density Ne=(1.2-1.6)1017 cm-3, which is detected from the shape and shift of aluminum and magnesium singly charged ion lines. Two low Ne values detected from the Hβ and large Ne measured from the widths and shift of ion lines suggest presence of three types of discharges during PEO with aluminum- and magnesium-alloy anode. On the basis of present and earlier results one can conclude that low Ne processes do not depend upon anode material or electrolyte composition.The electron temperature of 4000 K and 33,000 K are determined from relative intensities of Mg I and O II lines, respectively. The attention is drawn to the possibility of Ne application for Te evaluation using Saha equation what is of importance for PEO metal plasma characterization. During the course of this study, difficulties in the analysis of spectral line shapes are encountered and the ways to overcome some of the obstacles are demonstrated.

  20. A study on the recycling of aluminium alloy 7075 scrap

    Energy Technology Data Exchange (ETDEWEB)

    Oezer, Goekhan [Yildiz Technical Univ., Yildiz (TR). Balkan Centre of Advanced Casting Technologies (BACAT); Marsoglu, Muezeyyen [Yildiz Technical Univ., Yildiz (Turkey). Dept. for Metal and Materials Science Engineering; Burgucu, Sarp

    2012-07-01

    Aluminium and its alloys have recently become an important metal whose area and amount of usage increase more and more, due to their mechanical properties, recycling ability, and penetrability. If it is considered that the bauxite, which is the raw material of aluminium is rare on earth, and also the area and amount of aluminium usage increases over time, the importance of aluminium recycling goes up. aluminium recycling has become crucial by means of both, the potential of the scrap's dependant increase on usage and the primary aluminium production, as it is providing energy and cost savings. 7xxx grades of scrap are collected with other scrap of aluminium alloys in one turn and recycled all together. As the regain of these alloys is not done by isolation of the various grades, the finally recycled ingots result in lower grades. High value aluminium scrap is regrettably not recovered, as it was anticipated. This study is dealing with 7075 aluminium alloys originated from discharged blow molding tools and the rest piece cuttings of blocks and plates. The material has been subjected to an induction furnace, and has been remelted into small ingots and hardened according to 7075 aluminium alloy parameters (hardening aluminium tooling). [German] Aluminium und seine Legierungen sind in den letzten Jahren aufgrund ihrer mechanischen Eigenschaften, ihrer Recyclingfaehigkeit und ihrer Durchlaessigkeit immer bedeutendere metallische Werkstoffe geworden. Unter Beruecksichtigung, dass Bauxit als Rohmaterial selten auf der Erde vorkommt und der Verbrauch mit der Zeit steigt, waechst die Bedeutung des Recyclings von Aluminium. Aluminiumrecycling, zumal es Energieund Kosteneinsparungen ermoeglicht, ist sowohl fuer die schrottabhaengigen Verwendungspotentiale und die PrimaerAluminiumproduktion gleichermassen bedeutend geworden. Die 7xxxx Schrottlegierungen werden in einem Arbeitsgang mit dem Schrott aus anderen Aluminiumlegierungen gesammelt und recycled. Da die

  1. Effects of aluminium surface morphology and chemical modification on wettability

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

    2014-03-01

    Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

  2. There is (still too much aluminium in infant formulas

    Directory of Open Access Journals (Sweden)

    Burrell Shelle-Ann M

    2010-08-01

    Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

  3. Electrolytic deposition of aluminium-magnesium-alloys from electrolytes containing organo-aluminium complexes; Elektrolytische Abscheidung von Aluminium-Magnesium-Legierungen aus aluminiumorganischen Komplexelektrolyten

    Energy Technology Data Exchange (ETDEWEB)

    Lehmkuhl, H.; Mehler, K.; Bongard, H.; Tesche, B. [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany); Reinhold, B. [Audi AG, Ingolstadt (Germany). Technische Entwicklung

    2000-10-01

    The galvanic deposition of pure aluminium from fluoride-containing electrolytes has been developed further and for the first time aluminium and magnesium have been deposited from a toluene-solution of a halide-free organo-aluminium complex electrolyte. The rate of incorporation of magnesium can be controlled over a wide range by either adjusting the composition of the aluminium-magnesium anode or by using separate aluminium or magnesium anodic circuits. The current efficiency for both anode and cathode approaches 100%. The resulting coating is optically attractive and, depending upon the magnesium-content or the cathodic current density, can be formed as a dull or polished surface. Investigations using an electron microscope show that the surface, in contrast to that of pure aluminium, consists of spherical particles. The aluminium-magnesium coating provides excellent protection against the corrosion of magnesium components. Electrochemical investigations using, for example 25% by weight magnesium incorporation, indicate a pronounced passivity interval compared to the alloy AZ91hp. In contrast to galvanic zinc-plated and silicate-sealed examples, cyclic corrosion tests on screws simulating 10 years of exposure, show no corrosion. (orig.)

  4. Comparative study of the cytotoxic and genotoxic effects of titanium oxide and aluminium oxide nanoparticles in Chinese hamster ovary (CHO-K1) cells

    International Nuclear Information System (INIS)

    The aim of this study was to analyze the cytotoxicity and genotoxicity of titanium oxide (TiO2) and aluminium oxide (Al2O3) nanoparticles (NPs) on Chinese hamster ovary (CHO-K1) cells using neutral red (NR), mitochondrial activity (by MTT assay), sister chromatid exchange (SCE), micronucleus (MN) formation, and cell cycle kinetics techniques. Results showed a dose-related cytotoxic effect evidenced after 24 h by changes in lysosomal and mitochondrial dehydrogenase activity. Interestingly, transmission electronic microscopy (TEM) showed the formation of perinuclear vesicles in CHO-K1 cells after treatment with both NPs during 24 h but no NP was detected in the nuclei. Genotoxic effects were shown by MN frequencies which significantly increased at 0.5 and 1 μg/mL TiO2 and 0.5-10 μg/mL Al2O3. SCE frequencies were higher for cells treated with 1-5 μg/mL TiO2. The absence of metaphases evidenced cytotoxicity for higher concentrations of TiO2. No SCE induction was achieved after treatment with 1-25 μg/mL Al2O3. In conclusion, findings showed cytotoxic and genotoxic effects of TiO2 and Al2O3 NPs on CHO-K1 cells. Possible causes of controversial reports are discussed further on.

  5. Gas heat treatment plants for the aluminium industry; Gasbeheizte Waermebehandlungsanlagen fuer die Aluminium-Industrie

    Energy Technology Data Exchange (ETDEWEB)

    Olberts, P.; Hanus, A. [LOI Thermprocess GmbH, Essen (Germany)

    2004-09-01

    LOI Thermoprocess has developed new, flexible, innovative furnace designs for heat treatment of aluminium in general (car industry) and particularly for cylinder heads, engine units, chassis components, textured components, wheels, rolled sheet and extrusions. The furnaces are heated by means of radiant tubes (recuperators) and by the more usual open gas heating system (flue gas recirculation). (orig.)

  6. The aluminium body has been promoted in Canada; La carrosserie aluminium promue au Canada

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2004-02-01

    The aluminium vehicles technology is a technology which allows, with an equivalent structure, to decrease the weight of a car of 40%. Presented by the Alcan firm, this technology is one of the technologies of the year 2003. The Alcan firm has, besides, received the 2003 technology price awarded by the magazine Industry Week. (O.M.)

  7. Pleiotropic protective roles of melatonin against aluminium-induced toxicity in rats.

    Science.gov (United States)

    Allagui, Mohamed S; Hachani, Rafik; Saidi, Saber; Feriani, Anouer; Murat, Jean C; Kacem, Kamel; El feki, Abdelfatteh

    2015-10-01

    This study aimed to investigate the potential effects of melatonin on aluminium-induced toxicity in a rat model using a set of biochemical, inflammatory, oxidant, lipid profile criteria and hepatic integrity (verified by hematoxylin-eosin staining). The results indicated that AlCl3 administration during 60 days (100 mg/kg b.w.) significantly increased the activities of transaminases AST and ALT by 46% (p aluminium-intoxication.

  8. Sol-gel derived nanocomposite materials for corrosion protection of aluminium alloys

    OpenAIRE

    Schmidt, Helmut K.; Müller, Peter; Dittfurth, Carola; Albayrak, Sener; Puhl, Anne

    2000-01-01

    Thermally curable nanocomposite coating materials have been developed to seal and protect copper-containing aluminium alloys against corrosion. The coating material was prepared via the sol-gel-process starting from epoxy functionalised silanes, nanoscaled silica and organic diole crosslinker. This coating matrix was additionally supplied with a varying content of cerium oxide (1-20 wt.%). The corrosion protective efficiency of these coatings was investigated on aluminium alloys Al 6013-T6 an...

  9. Electrochemical Characterization of Al2 O3 -Ni Thin Film Selective Surface on Aluminium

    OpenAIRE

    KADIRGAN, Figen

    1999-01-01

    Solar thermal collectors represent a widely used type of system for the conversion of solar energy. In order to produce selective coatings on aluminium substrates to be used as absorber plates in high efficiency solar collectors, nickel pigmentation was applied to anodically oxidised surfaces. Electrochemical dc methods are used to study the oxidation of aluminium as functions of the following electrolysis conditions: applied current, pH, temperature and concentration of electrolyte....

  10. Modelling of detonation cellular structure in aluminium suspensions

    Science.gov (United States)

    Briand, A.; Veyssiere, B.; Khasainov, B. A.

    2010-12-01

    Heterogeneous detonations involving aluminium suspensions have been studied for many years for industrial safety policies, and for military and propulsion applications. Owing to their weak detonability and to the lack of available experimental results on the detonation cellular structure, numerical simulations provide a convenient way to improve the knowledge of such detonations. One major difficulty arising in numerical study of heterogeneous detonations involving suspensions of aluminium particles in oxidizing atmospheres is the modelling of aluminium combustion. Our previous two-step model provided results on the effect on the detonation cellular structure of particle diameter and characteristic chemical lengths. In this study, a hybrid model is incorporated in the numerical code EFAE, combining both kinetic and diffusion regimes in parallel. This more realistic model provides good agreement with the previous two-step model and confirms the correlations found between the detonation cell width, and particle diameter and characteristic lengths. Moreover, the linear dependence found between the detonation cell width and the induction length remains valid with the hybrid model.

  11. Nouveau procédé de synthèse du nitrure d'aluminium

    Science.gov (United States)

    Haussonne, J. M.; Lostec, J.; Bertot, J. P.; Lostec, L.; Sadou, S.

    1993-04-01

    Thermodynamic considerations show that, even at room temperature, pure aluminium can react with nitrogen to form the aluminium nitride AlN. However, pure aluminium does not exist: it is always surrounded by an alumina shell that protects the metal from further reactions. Furthermore, in the hypothesis where one has been able to make aluminium react with nitrogen, an aluminium nitride shell will protect as well the metal core from further oxidation. Prompted by the Lanxide process allowing to form Al/Al2O3 composites, we have mixed aluminium powders with lithium salts, and easily synthesized pure aluminium nitride by heating the mixed powders in nitrogen at temperatures ranging from 800 to 1200 °C. Starting from aluminium powders with a specific area ranging from 0.3 to 4 m^2/g, we have been able to produce aluminium nitride with specific are ranging from 1 to 20 m^2/g. Mixed with Y203-CaO and sintered at 1720 °C in N2, we obtained AIN ceramics owning 92% density and 160 W/m.K thermal conductivity. Les calculs thermodynamiques montrent que, même à température ambiante, l'aluminium pur peut réagir avec l'azote pour former le nitrure d'aluminium AlN. Cependant, la poudre d'aluminium pur n'existe pas : ses grains sont toujours entourés d'une couche d'alumine protectrice. De plus, dans l'hypothèse où l'on pourrait faire réagir de la poudre d'aluminium avec de l'azote, il se formerait de même une couche protectrice de nitrure d'aluminium qui empêcherait le centre des grains de réagir. S'inspirant du “procédé Lanxide” permettant de réaliser des composites Al/Al2O3, nous avons mélangé de la poudre d'aluminium avec des sels de lithium, et synthétisé du nitrure d'aluminium pur en portant ce mélange dans l'azote à une température pouvant être comprise entre 800 et 1 200 °C. Utilisant des poudres d'aluminium possédant une surface spécifique comprise entre 0,3 et 4 m^2/g, nous avons obtenu une poudre de nitrure d'aluminium avec une surface sp

  12. Combined Corrosion and Wear of Aluminium Alloy 7075-T6

    NARCIS (Netherlands)

    Liu, Y.; Mol, J.M.C.; Janssen, G.C.A.M.

    2016-01-01

    The aluminium alloy 7075-T6 is widely used in engineering. In some applications, like slurry transport, corrosion and abrasion occur simultaneously, resulting in early material failure. In the present work, we investigated the combined effect of corrosion and wear on the aluminium alloy 7075-T6. We

  13. Aluminium removal from water after defluoridation with the electrocoagulation process.

    Science.gov (United States)

    Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

    2015-01-01

    Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

  14. New Policies to Control the Aluminium Industry Expansion

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>Information from China Nonferrous Metals Industry Association (CNIA) shows that new government policies on China’s aluminium industry will be released soon in order to control the rapid expansion of the aluminium industry which consumes large amount of power resources. Based on the new policies, investors of

  15. Chalco Calls for End of More Control Measures on Aluminium

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> To control the investment rush in electrolyticaluminium in recent years and ensure thehealthy development of China’s aluminium in-dustry, the State Council recently released aseries of adjustment policies and control meas-ures,which effectively prevented theinvestment rush and limited the aluminium out-put growth.

  16. Haemodialysis related osteomalacia: a staining method to demonstrate aluminium

    OpenAIRE

    Buchanan, Malcolm RC; Ihle, Benno U; Dunn, Cheryl M

    1981-01-01

    A slight modification in tissue processing and staining technique enables a previously described method for staining aluminium to be used to demonstrate aluminium in osteomalacia associated with haemodialysis. The stain appears to be accurate in diagnosing this condition and may assist in establishing the diagnosis before severe osteomalacia develops.

  17. Developments in finite element simulations of aluminium extrusion

    NARCIS (Netherlands)

    Lof, Joeri

    2000-01-01

    Aluminium extrusion is a forming process used to produce profiles. A large variety of profiles can be made by pressing a billet of hot aluminium through a hole that closely resembles the required cross-section of the profie. At the present time, design of extrusion dies and operation in extrusion co

  18. CAD implementation of design rules for aluminium extrusion dies

    NARCIS (Netherlands)

    Ouwerkerk, van Gijs

    2009-01-01

    Aluminium extrusion is an industrial forming process that is used to produce long profiles of a constant cross-section. This cross-section is shaped by the opening in a steel tool known as the die. The understanding of the mechanics of the aluminium extrusion process is still limited. The flow of al

  19. Enhanced corrosion protection by microstructural control of aluminium brazing sheet

    NARCIS (Netherlands)

    Norouzi Afshar, F.

    2013-01-01

    Aluminium brazing sheet is a sandwich material made out of two aluminium alloys (AA4xxx/AA3xxx) and is widely used in automotive heat exchangers. One of the main performance criteria for heat exchanger units is the lifetime of the product. The lifetime of the heat exchanger units is determined by th

  20. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  1. CERN: very large magnet with aluminium winding

    Energy Technology Data Exchange (ETDEWEB)

    Wittgenstein, F.A.

    1984-10-25

    The construction of an octagonal solenoid from trapezoidal plates of Al, 6m long and 6cm thick, assembled by electron beam welding, for installation in a laboratory 50m underground is described. The objective is to create a field of 0.5T in a volume of 1000m/sup 3/ for the L3 particle detector of the LEP accelerator project. Principal dimensions and weights of the structure are given and its three stages of implementation are described, with reference to the contributions from the Swiss aluminium industry.

  2. Friction stir welding of single crystal aluminium

    DEFF Research Database (Denmark)

    Fonda, Richard Warren; Wert, John A.; Reynolds, A.P.;

    2007-01-01

    Friction stir welds were prepared in different orientations in an aluminium single crystal. The welds were quenched to preserve the microstructure surrounding the tool and then electron backscattered diffraction was used to reveal the generation of grain boundaries and the evolution...... of crystallographic texture around the tool in each weld. The extent of both dynamic recrystallisation and conventional recrystallisation varied considerably as a function of weld orientation. As the base plate begins to interact with the deformation field surrounding the tool, regions of the single crystal rotate...

  3. New sheet aluminium qualities for low-cost lightweight constructions; Neue Aluminium-Blechqualitaeten fuer den kosteneffizienten Leichtbau

    Energy Technology Data Exchange (ETDEWEB)

    Bloeck, M.; Furrer, P. [Novelis Technology AG, Neuhausen (Switzerland)

    2005-11-01

    Aluminium alloys used for car bodies have a wide range of material characteristics. New developments focus on selective development of material and surface characteristics for obtaining sheet aluminium qualities optimized for specific applications. These and further measures taken by Novelis are to reduce material consumption, simplify process steps in motor car manufacturing and reducing the overall system cost. (orig.)

  4. Design of the lines of aluminium drawing. Part 2; Conception des filieres de filage d'aluminium. Partie 2

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    This work is the second part of the file 'design of the lines of aluminium drawing'. It gives elements for structuring the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  5. Enhancing low-field magnetoresistance of La0.67Ca0.33MnO3 films deposited on anodized aluminium-oxide membranes

    Institute of Scientific and Technical Information of China (English)

    Tang Wei-Hua; Li Pei-Gang; Lei Ming; Guo Yan-Feng; Chen Lei-Ming; Li Ling-Hong; Song Peng-Yun; Chen ChinPing

    2006-01-01

    In this paper we report a new method to fabricate nanostructured films.La0.67Ca0.33MnO3(LCMO)nanostructured films have been fabricated by using pulsed electron beam deposition (PED) on anodized aluminium oxide (AAO)membranes.The magnetic and electronic transport properties are investigated by using the Quantum Design physics properties measurement system (PPMS) and magnetic properties measurement system (MPMS).The resistance peak temperature (Tp) is about 85 K and the Curie temperature(Tc) is about 250 K for the LCMO film on an AAO membrane with a pore diameter of 20 nm.Large magnetoresistance ratio (MR) is observed near Tp.The MR is as high as 85 %under 1T magnetic field.The great enhancement of MR at low magnetic fields could be attributed to the lattice distortion and the grain boundary that are induced by the nanopores on the AAO membrane.

  6. Aluminium matrix composites: Challenges and opportunities

    Indian Academy of Sciences (India)

    M K Surappa

    2003-02-01

    Aluminium matrix composites (AMCs) refer to the class of light weight high performance aluminium centric material systems. The reinforcement in AMCs could be in the form of continuous/discontinuous fibres, whisker or particulates, in volume fractions ranging from a few percent to 70%. Properties of AMCs can be tailored to the demands of different industrial applications by suitable combinations of matrix, reinforcement and processing route. Presently several grades of AMCs are manufactured by different routes. Three decades of intensive research have provided a wealth of new scientific knowledge on the intrinsic and extrinsic effects of ceramic reinforcement vis-a-vis physical, mechanical, thermo-mechanical and tribological properties of AMCs. In the last few years, AMCs have been utilised in high-tech structural and functional applications including aerospace, defence, automotive, and thermal management areas, as well as in sports and recreation. It is interesting to note that research on particle-reinforced cast AMCs took root in India during the 70’s, attained industrial maturity in the developed world and is currently in the process of joining the mainstream of materials. This paper presents an overview of AMC material systems on aspects relating to processing, microstructure, properties and applications.

  7. Reactions on carbon anodes in aluminium electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Eidet, Trygve

    1997-12-31

    The consumption of carbon anodes and energy in aluminium electrolysis is higher than what is required theoretically. This thesis studies the most important of the reactions that consume anode materials. These reactions are the electrochemical anode reaction and the airburn and carboxy reactions. The first part of the thesis deals with the kinetics and mechanism of the electrochemical anode reaction using electrochemical impedance spectroscopy. The second part deals with air and carboxy reactivity of carbon anodes and studies the effects of inorganic impurities on the reactivity of carbon anodes in the aluminium industry. Special attention is given to sulphur since its effect on the carbon gasification is not well understood. Sulphur is always present in anodes, and it is expected that the sulphur content of available anode cokes will increase in the future. It has also been suggested that sulphur poisons catalyzing impurities in the anodes. Other impurities that were investigated are iron, nickel and vanadium, which are common impurities in anodes which have been reported to catalyze carbon gasification. 88 refs., 92 figs., 24 tabs.

  8. Comparative study of the cytotoxic and genotoxic effects of titanium oxide and aluminium oxide nanoparticles in Chinese hamster ovary (CHO-K1) cells

    Energy Technology Data Exchange (ETDEWEB)

    Di Virgilio, A.L. [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), Diag. 113 y 64, Correo 16, Suc. 4, La Plata (1900) (Argentina); Reigosa, M. [Instituto Multidisciplinario de Biologia Celular (IMBICE), Calle 526 y Camino Gral. Belgrano (entre 10 y 11), La Plata 1900 (Argentina); Arnal, P.M. [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), Diag. 113 y 64, Correo 16, Suc. 4, La Plata 1900 (Argentina); Fernandez Lorenzo de Mele, M., E-mail: mmele@inifta.unlp.edu.ar [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas (INIFTA), Diag. 113 y 64, Correo 16, Suc. 4, La Plata 1900 (Argentina)

    2010-05-15

    The aim of this study was to analyze the cytotoxicity and genotoxicity of titanium oxide (TiO{sub 2}) and aluminium oxide (Al{sub 2}O{sub 3}) nanoparticles (NPs) on Chinese hamster ovary (CHO-K1) cells using neutral red (NR), mitochondrial activity (by MTT assay), sister chromatid exchange (SCE), micronucleus (MN) formation, and cell cycle kinetics techniques. Results showed a dose-related cytotoxic effect evidenced after 24 h by changes in lysosomal and mitochondrial dehydrogenase activity. Interestingly, transmission electronic microscopy (TEM) showed the formation of perinuclear vesicles in CHO-K1 cells after treatment with both NPs during 24 h but no NP was detected in the nuclei. Genotoxic effects were shown by MN frequencies which significantly increased at 0.5 and 1 {mu}g/mL TiO{sub 2} and 0.5-10 {mu}g/mL Al{sub 2}O{sub 3}. SCE frequencies were higher for cells treated with 1-5 {mu}g/mL TiO{sub 2}. The absence of metaphases evidenced cytotoxicity for higher concentrations of TiO{sub 2}. No SCE induction was achieved after treatment with 1-25 {mu}g/mL Al{sub 2}O{sub 3}. In conclusion, findings showed cytotoxic and genotoxic effects of TiO{sub 2} and Al{sub 2}O{sub 3} NPs on CHO-K1 cells. Possible causes of controversial reports are discussed further on.

  9. INTEROGATION OF THE MANUFACTURING ROUTE OF ALUMINIUM AA 1050 USED IN LITHOGRAPHIC APPLICATION

    OpenAIRE

    Witkowska, Malgorzata Danuta

    2013-01-01

    The aluminium AA1050 alloy, known as commercially pure aluminium, contains 99.5% Al, together with Fe and Si as major alloying elements. During fabrication of aluminium substrates for lithographic printing plates in Bridgnorth Aluminium Ltd, the AA 1050 aluminium alloy proceeds through various stages of thermomechanical processing, with the conditions at each processing stage influencing the microstructure of the final coil. Because of its specific gravity, tensile strength, surface performa...

  10. The effect of atmospheric corona treatment on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.;

    2010-01-01

    The effect of atmospheric corona discharge on AM 050 aluminium surface was investigated using electrochemical polarization, SEM-EDX, FIB-SEM. and XPS. The corona treatment was performed with varying time (1, 5, and 15 min) in atmospheric air. A 200 nm oxide layer was generated on AA1050 after...... the 15 min air corona treatment. A significant reduction in anodic and cathodic reactivities was observed starting from 1 min exposure, which further decreased with prolonged exposure (15 min) and after delayed testing (after 30 days). The reduction in surface reactivity is due to the formation...

  11. Determination of phosphorus in hypereutectic aluminium-silicon alloys.

    Science.gov (United States)

    Mukai, K

    1972-04-01

    A reproducible method is described for determination of small amounts of phosphorus (from 0.0005% to 0.02%) in hypereutectic aluminium-silicon complex alloys. The method permits the separate determination of phosphorus in acid-soluble and acid-insoluble fractions. Phosphomolybdate is extracted with n-butanol-chloroform solvent mixture and back-extracted with a btannous chloride reducing solution. The phosphorus content of a sample cut into small pieces decreases during storage; loss of phosphorus is negligible on acid dissolution under oxidizing conditions. PMID:18961077

  12. Aluminium: Aluminij: kovina izbire: the metal of choice:

    OpenAIRE

    Gándara, María Josefa Freiría

    2013-01-01

    This article summarizes the importance of aluminium as the metal of choice formany applications. Aluminium is a lightweight, durable metal. It is silvery in appearance when freshly cut, is a good conductor of heat and electricity, and is easily shaped by moulding and extruding. Aluminium has two main advantages when compared with other metals. Firstly, it has a low density, about one-third that of iron and copper. Secondly, although it reacts rapidly with the oxygen in air, it forms a thin, t...

  13. Optimization of Magnesium Metal into Commercially Pure Aluminium

    Directory of Open Access Journals (Sweden)

    Vandana J Rao

    2014-02-01

    Full Text Available The present investigation, involve development of Al-Mg systems by addition of magnesium into commercially pure aluminium. The amounts of magnesium added into commercially pure aluminium are of 1 and 2 wt%. The recoveries of magnesium are around 85-90%.Remaining Mg react with oxygen and float on the liquid aluminium. Presence of magnesium creates two phenomena. One is solid solution hardening and other is intermetallics formation. Both the phenomena checked by microstructural changes and by measuring the electrical conductivity values. By increasing the Mg, content mechanical properties (hardness and tensile strength increases and electrical conductivity decreases.

  14. Effect of filtration on reoxidation proceses in aluminium alloys

    Directory of Open Access Journals (Sweden)

    D. Bolibruchova

    2010-01-01

    Full Text Available This article is focused on reoxidation processes during filtration of aluminium alloys. Many of our experimental works pointed out, that using filtration media placed in gating system causes reoxidation of poured aluminium alloy. Main aim of our latest work was to validate our arguments, that filter in gating system can be considered as obstacle for continuous pouring, with help of computer simulations. This article is only a small part of our researches focused on reoxidation processes during filtration of aluminium alloys.

  15. Corrosion issues of powder coated AA6060 aluminium profiles

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl;

    2015-01-01

    In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

  16. Thickness Evaluation of Aluminium Plate Using Pulsed Eddy Current Technique

    Science.gov (United States)

    Singh, Gurpartap; Bapat, Harsh Madhukar; Singh, Bhanu Pratap; Bandyopadhyay, Manojit; Puri, Rakesh Kumar; Badodkar, Deepak Narayanrao

    2013-10-01

    This paper describes a pulsed eddy current (PEC) based non-destructive testing system used for detection of thickness variation in aluminium plate. A giant magneto-resistive sensor has been used instead of pick up coil for detecting resultant magnetic field. The PEC response signals obtained from 1 to 5 mm thickness change in aluminium plate were investigated. Two time domain features, namely peak value and time to peak, of PEC response were used for extracting information about thickness variation in aluminium plate. The variation of peak value and time to peak with thickness was compared. A program was developed to display the thickness variation of the tested sample.

  17. Radiation-induced creep of copper, aluminium and their alloys

    International Nuclear Information System (INIS)

    The results of creep studies on copper, aluminium and their alloys with and without neutron irradiation are presented. The experiments are carried out at the WWR-K reactor at the neutron fluence of 1.4.1016 n/m2.s (2.5.1016 n/m2.s, E>0.1 MeV). Polycrystalline copper (99.99 and 99.95%), aluminium (99.99%) and the alloys of copper with 4 at% of titanium, of aluminium with 4.2% of copper are studied within the temperature interval 0.31-0.51 Tm. (orig.)

  18. Study of fatigue behaviour of 7475 aluminium alloy

    Indian Academy of Sciences (India)

    B B Verma; J D Atkinson; M Kumar

    2001-04-01

    Fatigue properties of a thermomechanically treated 7475 aluminium alloy have been studied in the present investigation. The alloy exhibited superior fatigue life compared to conventional structural aluminium alloys and comparable stage II crack growth rate. It was also noticed that the fatigue crack initiated from a surface grain and the crack extension was dominated by ductile striations. Analysis also revealed that this alloy possessed fracture toughness and tensile properties superior to that noticed with other structural aluminium alloys. Therefore the use of this alloy can safely reduce the overall weight of the aircraft.

  19. Performance of commercial aluminium alloys as anodes in gelled electrolyte aluminium-air batteries

    Science.gov (United States)

    Pino, M.; Chacón, J.; Fatás, E.; Ocón, P.

    2015-12-01

    The evaluation of commercial aluminium alloys, namely, Al2024, Al7475 and Al1085, for Al-air batteries is performed. Pure Al cladded Al2024 and Al7475 are also evaluated. Current rates from 0.8 mA cm-2 to 8.6 mA cm-2 are measured in a gel Al-air cell composed of the commercial alloy sample, a commercial air-cathode and an easily synthesizable gelled alkaline electrolyte. The influence of the alloying elements and the addition to the electrolyte of ZnO and ZnCl2, as corrosion inhibitors is studied and analysed via EDX/SEM. Specific capacities of up to 426 mAh/g are obtained with notably flat potential discharges of 1.3-1.4 V. The competition between self-corrosion and oxidation reactions is also discussed, as well as the influence of the current applied on that process. Al7475 is determined to have the best behaviour as anode in Al-air primary batteries, and cladding process is found to be an extra protection against corrosion at low current discharges. Conversely, Al1085 provided worse results because of an unfavourable metallic composition.

  20. Aluminium content of some foods and food products in the USA, with aluminium food additives.

    Science.gov (United States)

    Saiyed, Salim M; Yokel, Robert A

    2005-03-01

    The primary objective was to determine the aluminium (Al) content of selected foods and food products in the USA which contain Al as an approved food additive. Intake of Al from the labeled serving size of each food product was calculated. The samples were acid or base digested and analysed for Al using electrothermal atomic absorption spectrometry. Quality control (QC) samples, with matrices matching the samples, were generated and used to verify the Al determinations. Food product Al content ranged from Cheese in a serving of frozen pizzas had up to 14 mg of Al, from basic sodium aluminium phosphate; whereas the same amount of cheese in a ready-to-eat restaurant pizza provided 0.03-0.09 mg. Many single serving packets of non-dairy creamer had approximately 50-600 mg Al kg(-1) as sodium aluminosilicate, providing up to 1.5 mg Al per serving. Many single serving packets of salt also had sodium aluminosilicate as an additive, but the Al content was less than in single-serving non-dairy creamer packets. Acidic sodium aluminium phosphate was present in many food products, pancakes and waffles. Baking powder, some pancake/waffle mixes and frozen products, and ready-to-eat pancakes provided the most Al of the foods tested; up to 180 mg/serving. Many products provide a significant amount of Al compared to the typical intake of 3-12 mg/day reported from dietary Al studies conducted in many countries. PMID:16019791

  1. Adsorption of aluminium by stream particulates.

    Science.gov (United States)

    Tipping, E; Ohnstad, M; Woof, C

    1989-01-01

    An experimental study was made of the adsorption of aluminium by fine particulates from Whitray Beck, a hill stream in NW England. Adsorption increased with Al(3) activity, pH and concentration of particles, and could be quantitatively described by the empirical equation: [Formula: see text] [particles] where square brackets indicate concentrations, curly brackets, activities, and alpha, beta and gamma are constants with values of 5.14x10(-10) (mol litre(-1))(2.015) (g particles litre(-1))(-1), 0.457, and 1.472, respectively. For the experimental data, the equation gave a correlation ratio of 0.99. The equation accounts reasonably well for the adsorption of Al by particulates from seven other streams. In applying the equation, it must be borne in mind that the desorption kinetics of Al depend on pH, and rapid reversibility (or=10%) of total monomeric Al. PMID:15092454

  2. Mechanical behaviour of aluminium-lithium alloys

    Indian Academy of Sciences (India)

    N Eswara Prasad; A A Gokhale; P Rama Rao

    2003-02-01

    Aluminium-lithium alloys hold promise of providing a breakthrough response to the crying need for lightweight alloys for use as structurals in aerospace applications. Considerable worldwide research has gone into developing a range of these alloys over the last three decades. As a result, substantial understanding has been developed of the microstructure-based micromechanisms of strengthening, of fatigue and fracture as well as of anisotropy in mechanical properties. However, these alloys have not yet greatly displaced the conventionally used denser Al alloys on account of their poorer ductility, fracture toughness and low cycle fatigue resistance. This review aims to summarise the work pertaining to study of structure and mechanical properties with a view to indicate the directions that have been and can be pursued to overcome property limitations.

  3. Microstructure and interfaces of a reaction coating on aluminium alloys by laser processing

    OpenAIRE

    Zhou, X.B.; De Hosson, J. Th. M.

    1993-01-01

    This paper reports an approach to coat a ceramic layer on aluminium alloys by means of chemical reaction. The reaction product of Al2O3 layer of 100 µm in thickness has been formed using a powder mixture of silicon oxide and aluminium by laser processing. It turns out that the large amount of heat from the exothermic reaction has a predominate effects on the formation of the oxide layer. Further, the negative free energy of the reaction may promote the metal/oxide wetting. The micro-hardness ...

  4. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud.

  5. COMPARATION BETWEEN NONDESTRUCTIVE TESTING METHODS FOR THE ALUMINIUM BRAZED PIECES

    Directory of Open Access Journals (Sweden)

    Dan NIŢOI

    2014-05-01

    Full Text Available Presented paper refers to different control methods used in aluminium brazed joining because of possible defects. Low joining complexity permits exact damages position in relation with materials geometry.

  6. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. PMID:26365318

  7. Deposition of aluminium nanoparticles using dense plasma focus device

    International Nuclear Information System (INIS)

    Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

  8. Aluminium dynamics and proton buttering in undistributed samples of acidified forest soils; Aluminium-Dynamik und Protonenpufferung in ungestoerten Proben versauerter Waldboeden

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, E.

    1992-12-31

    In this work non-displaced soil samples were used to test the reaction of acidified forest soils in the aluminium buffering range to different proton concentrations. The examined quantities were the proton buffering rate in the macropore spaces and the correlated rate of aluminium release. Furthermore, the types of aluminium bondage occuring in the soil solution and their influence on the aluminium dynamics within the profile were determined. The significance of species distribution for the interpretation of the toxic potential of aluminium is illuminated. The influence of soil structure on proton buffering, aluminium release and species distribution is described from a global viewpoint. (orig.) [Deutsch] In der vorliegenden Arbeit wird an natuerlich gelagerten Bodenproben die Reaktion versauerter Waldboeden im Aluminium-Pufferbereich auf unterschiedlich starke Protonenbelastungen untersucht. Dabei interessiert die Rate der Protonenpufferung im Makroporenraum einhergehend mit der Menge freigesetzten Aluminiums. Darueberhinaus wird untersucht, welche Aluminium-Bindungsformen in der Bodenloesung vorliegen und welchen Einfluss diese auf die Aluminium-Dynamik innerhalb des Profils haben. Die Bedeutung der Speziesverteilung fuer die Interpretation potentieller Aluminium-Toxizitaet wird beleuchtet. Uebergreifend wird der Einfluss der Bodenstruktur auf Protonenpufferung, Aluminium-Freisetzung sowie Speziesverteilung herausgestellt. (orig.)

  9. Effect of heat treatment on anodic activation of aluminium by trace element indium

    Energy Technology Data Exchange (ETDEWEB)

    Graver, Brit [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Helvoort, Antonius T.J. van [Department of Physics, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Nisancioglu, Kemal, E-mail: kemal.nisancioglu@material.ntnu.n [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway)

    2010-11-15

    Research highlights: {yields} Indium segregation activates AlIn alloy surface anodically in chloride solution. {yields} Enrichment of In on Al surface can occur thermally by heat treatment at 300 {sup o}C. {yields} Increasing temperature homogenises indium in aluminium reducing anodic activation. {yields} Indium can activate AlIn surface by segregating through dealloying of aluminium. {yields} Anodic activation is caused by AlIn amalgam formation at aluminium surface. - Abstract: The presence of trace elements in Group IIIA-VA is known to activate aluminium anodically in chloride environment. The purpose of this paper is to investigate the surface segregation of trace element In by heat treatment and resulting surface activation. Model binary AlIn alloys, containing 20 and 1000 ppm by weight of In, were characterized after heat treatment at various temperatures by use of glow discharge optical emission spectroscopy, electron microscopy and electrochemical polarization. Heat treatment for 1 h at 300 {sup o}C gave significant segregation of discrete In particles (thermal segregation), which activated the surface. Indium in solid solution with aluminium, obtained by 1 h heat treatment at 600 {sup o}C, also activated by surface segregation of In on alloy containing 1000 ppm In, resulting from the selective dissolution of the aluminium component during anodic oxidation (anodic segregation). The effect of anodic segregation was reduced by decreasing indium concentration in solid solution; it had negligible effect at the 20 ppm level. The segregated particles were thought to form a liquid phase alloy with aluminium during anodic polarization, which in turn, together with the chloride in the solution destabilized the oxide.

  10. China’s Export of Fabricated Aluminium Keeps Rising

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>Affected by the State macro economic adjustment policies, China’s export of primary aluminium has decreased obviously. However, China’s export of fabricated aluminum is increasing rapidly, which has led to the investment rush of the aluminium industry, leading to the serious concern by the government. Market rumors are spreading that the government will soon adjust the export tax rebate rates so as to curb such a trend.

  11. Modeling of aluminium deposition from chloroaluminate ionic liquids

    OpenAIRE

    Schaltin, Stijn; Ganapathi, Murugan; Binnemans, Koen; Fransaer, Jan

    2011-01-01

    A finite-element model of the electrodeposition of aluminium from chloroaluminate ionic liquids is introduced. The purpose of this model is to give an explanation for the reasonable current densities that can be achieved in chloroaluminate ionic liquids despite the fact that the electrochemically active Al2Cl7- complexes are transformed into inactive AlCl4- complexes during the electrodeposition of aluminium. The obtainable current density in the electrodeposition from chloroaluminate ionic l...

  12. Metal-Ceramic Interfaces in Laser Coated Aluminium Alloys

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1994-01-01

    A novel process was developed to firmly coat an aluminium alloy, Al6061, with α-Al2O3 by means of laser processing. In this approach a mixture of SiO2 and Al powder was used to inject in the laser melted surface of aluminium. A reaction product α-Al2O3 layer of a thickness of 100 µm was created whic

  13. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    OpenAIRE

    Hamilta de Oliveira Santos; Marilene Morelli Serna; Nelson Batista de Lima; Isolda Costa; Jesualdo Luiz Rossi

    2005-01-01

    Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken f...

  14. Local electrochemical behaviour of 7xxx aluminium alloys

    OpenAIRE

    F. Andreatta

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a negative effect on safety and costs. This PhD thesis investigates the relation between electrochemical behaviour and microstructure of a number of 7xxx aluminium alloys: AA7075, AA7349 and an experime...

  15. Crushing modes of aluminium tubes under axial compression

    OpenAIRE

    Pled, Florent; Yan, Wenyi; Wen, Cui'e

    2014-01-01

    6 pages International audience A numerical study of the crushing of circular aluminium tubes with and without aluminium foam fillers has been carried out to investigate their buckling behaviours under axial compression. A crushing mode classification chart has been established for empty tubes. The influence of boundary conditions on crushing mode has also been investigated. The effect of foam filler on the crushing mode of tubes filled with foam was then examined. The predicted results ...

  16. Melting and solidification of bismuth inclusions in aluminium

    DEFF Research Database (Denmark)

    Thoft, N.B.; Bohr, J.; Buras, B.;

    1995-01-01

    Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different experime......Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different...

  17. Geometry Effects at Atomic-Size Aluminium Contacts

    OpenAIRE

    Schwingenschloegl, Udo; Schuster, Cosima

    2007-01-01

    We present electronic structure calculations for aluminium nanocontacts. Addressing the neck of the contact, we compare characteristic geometries to investigate the effects of the local aluminium coordination on the electronic states. We find that the Al 3pz states are very sensitive against modifications of the orbital overlap, which has serious consequences for the transport properties. Stretching of the contact shifts states towards the Fermi energy, leaving the system instable against fer...

  18. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Ivan Michalec

    2013-01-01

    Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  19. Blast Loaded Aluminium Plates : Experiments and numerical simulations

    OpenAIRE

    Melby, Emil Arne; Eide, Hilde Olaug Stakvik

    2013-01-01

    Light and flexible protective constructions in aluminium could be subjected to a blast load. In this thesis the effect of blast loading on aluminium plates of the type 1050A ? H14 was studied through experiments and numerical simulations. The effect of fragmentation was idealized with predrilled holes. The thesis was written at the Structural Impact Laboratory (SIMLab) at NTNU in collaboration with the Norwegian Defence Estates Agency (NDEA).Tensile tests revealed a clearly anisotropic behavi...

  20. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    OpenAIRE

    Napachat Tareelap; Kaysinee Sriraksasin; Nakorn Srisukhumbowornchai; Swieng Thuanboon; Choochat Nitipanyawong

    2014-01-01

    Due to the failure of manganese aluminium bronze (MAB) propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium...

  1. Lake restoration with aluminium, bentonite and Phoslock: the effect on sediment stability and light attenuation

    DEFF Research Database (Denmark)

    Egemose, Sara; Reitzel, Kasper; Flindt, Mogens

    treatments on aluminium mobility, sediment stability or light climate. A laboratory flume experiment including three shallow Danish lakes was conducted. We measured the effects of aluminium, Phoslock (a commercial product), bentonite, and a combination of bentonite/aluminium. Each treatment caused a varying...... consolidation of the sediment. The largest consolidation occurred using Phoslock- and bentonite-addition followed by bentonite/aluminium-addition, whereas aluminium alone had no effect. Sediment stability thresholds were measured before and after addition. Especially Phoslock, but also bentonite and bentonite....../aluminium increased sediment erosion threshold, with respectively 200%, 43% and 57%. Aluminium, bentonite/aluminium, and Phoslock improved the light conditions in the water phase, with respectively 60%, 57% and 50%, whereas bentonite created higher turbidity. Conclusively aluminium improved the light conditions...

  2. The binding, transport and fate of aluminium in biological cells.

    Science.gov (United States)

    Exley, Christopher; Mold, Matthew J

    2015-04-01

    Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion.

  3. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  4. TEM microstructure investigations of aluminium alloys used for laser alloying

    Directory of Open Access Journals (Sweden)

    K. Labisz

    2012-12-01

    Full Text Available Purpose: In this paper there are presented results of Transmission Electron Microscope investigation concerning the structure of the AlSi7Cu4 cast aluminium alloy using for alloying and remelting with the high power diode laser (HPDL. There are also presented the results of the thermo-derivative analysis performed using the UMSA (Universal Metallurgical Simulator and Analyser device, allowing to determine the specific points of the solidifying alloy, what is helpful for phase determination occurred in this alloy. In this work especially the changes of the precipitation type, size and shape were determined.Design/methodology/approach: The investigations were performed using electron microscopy for the microstructure and phases determination. By mind of the transmission electron microscopy, especially selected area diffraction method appliance it was possible to determine the phases occurred in the alloy in the as cast state. The morphology and size of the Mg2Si was also possible to determine as well the lattice parameters for this phase.Findings: : The reason of this work was also to present the laser treatment technology, which will be used for further alloying and remelting with ceramic powders – especially carbides and oxides. Particularly the overview will be directed on the laser power to achieve good layer hardness for protection of this hot work tool steel from losing their work stability and to make the tool surface more resistant to action in external conditions. The structure of the surface laser tray changes in a way, that there are very high roughness of the surface zone and the flatness or geometry changes in an important manner, crucial for further investigation.Research limitations/implications: The aluminium samples were examined metallographically using transmission electron microscope with different image techniques.Practical implications: Developing of new technology with appliance of Al alloys, High Power Diode Laser and

  5. Chapter 3. Chloric decomposition of aluminosilicate ores. 3.1. Features of chlorination of aluminium containing ores

    International Nuclear Information System (INIS)

    The features of chlorination of aluminium containing ores are considered in this article. Theoretical aspects of metals, oxides and natural compounds chlorination, specific features of synthesis of various chlorides are considered as well.

  6. Fiber remote and real time optoelectronic dosimetry based on the optically stimulated luminescence phenomenon: Development of sensors based on aluminium oxide doped with carbon for applications in personal dosimetry

    International Nuclear Information System (INIS)

    An optical fiber sensor based on the use of classical technologies (optoelectronic, laser, optical fibers,...) can be connected to the Optically Stimulated Luminescence properties (or OSL) of the aluminium oxide doped with carbon in order to provide several new capabilities compared to usual dosimeters: remote dose measurements, quasi 'real time' dose measurements, applied to personal dosimetry thanks to a low fading level at room temperature. This thesis work shows the studies about: 1)the state of the art about dosimetry based on the aluminium oxide doped with carbon and its OSL properties (emission and stimulation spectra, glow curves, trap and recombination energy levels,...), 2)the state of the art about international standardization, not only, with regard to personal dosimetry (IEC 61066 Standard) but also to the description of operational quantities called personal dose equivalent Hp(10) and Hp(0,07), 3)the experimental development of a new sensor device based on aluminium oxide crystals (design, realization, tests,...), 4)the application of statistical Monte Carlo calculation methods (code MCNP4B) to the simulation of the sensor head in accordance with the IEC Standard 61066 with regard to the energy and angular response Hp(10). (author)

  7. China Rescinds the Export Tax on Aluminium Alloys Made by Scrap

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>According to an official from the Tax Regulations Office under China’s State Council, from July 1st 2005, China will rescind the 5 per cent export tax on the aluminium alloys produced by using aluminium alloys scrap. An official from the State Council’s office said that through investigation they found that most aluminium alloys produced from aluminium scrap are not that energy consuming compared to primary aluminium. Starting from January 1st 2005, China decided to collect 5 per cent export tax on aluminium so as to control the industry development connected with high energy cost.

  8. Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

    Directory of Open Access Journals (Sweden)

    Senze Magdalena

    2015-03-01

    Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

  9. Ultraviolet Plasmonic Aluminium Nanoparticles for Highly Efficient Light Incoupling on Silicon Solar Cells

    Directory of Open Access Journals (Sweden)

    Yinan Zhang

    2016-05-01

    Full Text Available Plasmonic metal nanoparticles supporting localized surface plasmon resonances have attracted a great deal of interest in boosting the light absorption in solar cells. Among the various plasmonic materials, the aluminium nanoparticles recently have become a rising star due to their unique ultraviolet plasmonic resonances, low cost, earth-abundance and high compatibility with the complementary metal-oxide semiconductor (CMOS manufacturing process. Here, we report some key factors that determine the light incoupling of aluminium nanoparticles located on the front side of silicon solar cells. We first numerically study the scattering and absorption properties of the aluminium nanoparticles and the influence of the nanoparticle shape, size, surface coverage and the spacing layer on the light incoupling using the finite difference time domain method. Then, we experimentally integrate 100-nm aluminium nanoparticles on the front side of silicon solar cells with varying silicon nitride thicknesses. This study provides the fundamental insights for designing aluminium nanoparticle-based light trapping on solar cells.

  10. Corrosion behaviour of aluminium plates in aqueous medium

    International Nuclear Information System (INIS)

    The process of corrosion concerning the aluminium 1050 plate was studied at room temperatures, 45 and 600C in deionized water, the same Argonauta Reactor Water. Beyond the temperature influence, it was verified the effect of chloride ion and oxygen. It ws found that the amount of oxyde formed at room temperatures is almost negligible; at 45 and 600C the samples were covered with bayerita, the quantity of oxide formed at 450C being higher than at 600C. It was observed that there will be risk of corrosion in the case of Reactor Water to undergo contamination with chloride ions. The results have shown that the material can be used since the medium don't be strongly oxidizing. At potentials higher than - 900M sup(V) ess (-280 m sup(V) sub(H)), the material will undergo pitting corrosion. (Author)

  11. Calculation of Specific Heat for Aluminium Thin Films

    Institute of Scientific and Technical Information of China (English)

    LU Yao; SONG Qing-Lin; XIA Shan-Hong

    2005-01-01

    @@ We employ Prasher's non-dimensional form to analyse the size effects on specific heat of Al thin films. Compared the calculation results of pure aluminium film with the experimental data, it is found that the reduction of phonon states is not the main reason of the size effect on the specific heat Al thin films with thickness from 10hm to 370nm. However, the Al thin film in air usually has an oxidation layer and the specific heat of the layer is smaller than Al. By including the contribution of the oxidation layer to the thin-film specific heat, the calculation results are much closer to the experimental data. This may be a possible reason of the size effects on specific heat of Al thin films.

  12. Synthesis and characterization of alumina nano-powders by oxidation of molten aluminium in a thermal plasma reactor: Comparison with theoretical estimation

    International Nuclear Information System (INIS)

    Alumina nano-powders are formed in a thermal plasma reactor by in-flight reaction of micron-sized aluminium powders with atmospheric oxygen. Commercially available micron-sized aluminium powders are fed into the plasma jet using argon as a carrier gas. During in-flight, the particles are vaporized and get reacted with atmospheric oxygen. The reacted vapor nucleates and condenses on the water-cooled walls of the reaction chamber. Due to fast quenching, nanosized alumina particles were formed. The particles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron micrograph (TEM) and EDX. A simple model is developed and the particle size is compared with the experimental results. The theoretical estimation for the particle size is in well agreement with experiment result

  13. Acute aluminium phosphide poisoning, what is new?

    Directory of Open Access Journals (Sweden)

    Yatendra Singh

    2014-01-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide that is commonly used for grain preservation. AlP has currently generated interest with increasing number of cases in the past four decades because of its increased use for agricultural and nonagricultural purposes, and also its easy availability in the markets has led to its increased misuse to commit suicide. Ingestion is usually suicidal in intent, uncommonly accidental and rarely homicidal. The poison affects all systems, shock, cardiac arrhythmias with varied ECG changes and gastrointestinal features being the most prominent. Diagnosis is made on the basis of clinical suspicion, a positive silver nitrate paper test to phosphine, and gastric aspirate and viscera biochemistry. Treatment includes early gastric lavage with potassium permanganate or a combination of coconut oil and sodium bicarbonate, administration of charcoal and palliative care. Specific therapy includes intravenous magnesium sulphate and oral coconut oil. Unfortunately, the lack of a specific antidote Results in very high mortality and the key to treatment lies in rapid decontamination and institution of resuscitative measures. This article aims to identify the salient features and mechanism of AlP poisoning along with its management strategies and prognostic variables.

  14. Low cost aluminium metal matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Withers, G.

    2007-03-15

    Low cost, light weight Ultalite{reg_sign} is an Aluminium Metal Matrix Composite (AL-MMC) which utilises wear resistant ceramic particles derived from flyash. Ultalite AL-MMC typically contains between 10 and 30 per cent ceramic particles, and is formulated for the manufacture of wear resistant automotive components. Due to its low density and ease of processing into net shape die casting, Ultalite AL-MMC provides weight savings of up to 60 per cent over components fabricated from cast iron, thereby providing improved fuel efficiency with reduced greenhouse emissions. The original flyash material was sourced from a black coal power station in Queensland, where it contained a wide range of particles sizes. To narrow the size range and to remove impurities, a proprietary pretreatment developed by Dr Thomas Robl and co-researchers at the University of Kentucky was employed. The University of Kentucky developed the technology for the classification and benefaction of flyash to produce high-grade Pozzolan, which is used in Portland Cement product. This technology is now being applied to the production of Ultalite AL-MMC. Testing performed by Dr Robl has shown that the proprietary technology can eliminate the hollow particles, extract detrimental carbon-based impurities and remove the extremely fine and coarse particles. All that remains are dense ceramic particles with an average particle size of approximately 30 {mu}m. 9 refs., 3 figs.

  15. Fuzzy Multicriteria Ranking of Aluminium Coating Methods

    Science.gov (United States)

    Batzias, A. F.

    2007-12-01

    This work deals with multicriteria ranking of aluminium coating methods. The alternatives used are: sulfuric acid anodization, A1; oxalic acid anodization, A2; chromic acid anodization, A3; phosphoric acid anodization, A4; integral color anodizing, A5; chemical conversion coating, A6; electrostatic powder deposition, A7. The criteria used are: cost of production, f1; environmental friendliness of production process, f2; appearance (texture), f3; reflectivity, f4; response to coloring, f5; corrosion resistance, f6; abrasion resistance, f7; fatigue resistance, f8. Five experts coming from relevant industrial units set grades to the criteria vector and the preference matrix according to a properly modified Delphi method. Sensitivity analysis of the ranked first alternative A1 against the `second best', which was A3 at low and A7 at high resolution levels proved that the solution is robust. The dependence of anodized products quality on upstream processes is presented and the impact of energy price increase on industrial cost is discussed.

  16. Anomalous Diffusion of Mo Implanted into Aluminium

    Institute of Scientific and Technical Information of China (English)

    张通和; 吴瑜光; 邓志威; 钱卫东

    2001-01-01

    Mo ions are implanted into aluminium with a high ion flux and high dose at elevated temperatures of 300℃, 400℃ and 500℃ . X-ray diffraction spectra show that the Al12Mo phases are formed. Rutherford backscattering spectroscopy indicates that a profile of Mo appears in Al around the depth of 550nm and with an atomic concentration of ~7%, when Mo is implanted to the dose of 3 × 1017/cm2 with an ion flux of 45μA/cm2 (400℃).If the dose increases to 1 × 1018/cm2 at the same ion flux, the penetration of Mo ions in Al can reach a depth of 2μm, which is greater than the ion project range Rp (52.5nm). The results show that anomalous diffusion takes place. Owing to the intense atom collision cascades, the diffusion coefficient increases greatly with the increase of the ion flux and dose. The Mo diffusion coefficients in Al are calculated. The Mo retained dose in A1 increases obviously with the increase of the ion flux.

  17. Optical and morphological investigation of aluminium and nickel oxide composite films deposited by spray pyrolysis method as a basis of solar thermal absorber

    Indian Academy of Sciences (India)

    A Bagheri Khatibani; S M Rozati

    2015-04-01

    Applications of alumina and nickel oxide in various fields specially in solar energy conversion technology encouraged us to study physical properties of such materials. Hence after the deposition of the thin films on glass substrate by spray pyrolysis, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV–visible spectrophotometry, various physical properties were investigated. Different optical quantities such as optical band gap, refractive index, extinction coefficient, dielectric constants, volume and surface energy loss functions and optical conductivity were determined. Within this paper for different nickel to aluminium ratio (from 20/80 to 80/20 ratio) at specific substrate temperatures (300°C), decrease of optical transmittance with nickel content was notable. Using the transmittance data, other optical quantities were achieved by a numerical approximation method. We also observed an increase in the volume energy loss (VELF) more than the surface energy loss (SELF) and simultaneously a decrease trend prevailed according to nickel amount. On the basic of the XRD results, the amorphous phase changed by the presence of more nickel and according to SEM, more obvious nanosized spherical grains at higher nickel ratios can be observed.

  18. Aluminium Matrix Composites Reinforced with Co-continuous Interlaced Phases Aluminium-alumina Needles

    Directory of Open Access Journals (Sweden)

    Elvio de Napole Gregolin

    2002-09-01

    Full Text Available An Al-5SiO2 (5 wt% of SiO2 aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si/Al2O3 interlaced structure named co-continuous composite. A technique of powder metallurgy, using commercial aluminium powder and the silica fibers as starting materials, followed by hot extrusion, was used to produce the composite. The co-continuous microstructure was obtained partially or totally on the fibers as a result of the reaction, which occurs during the heat treatment, first by solid diffusion and finally by the liquid Al-Si in local equilibrium, formed with the silicon released by reaction. The internal structure of the fibers was characterized using field emission electron microscope (FEG-SEM and optical microscopy on polished and fractured samples.

  19. Fabrication experience of aluminium clad aluminium matrix dispersion fuels at BARC

    International Nuclear Information System (INIS)

    Aluminium clad, aluminium matrix plate type dispersion fuels have been fabricated in BARC in recent years as part of fuel development programme for small non-power research reactors. The present paper describes the flowsheet developed for fabrication of Al-UAlx, Al-U3Si2 and Al-U3O8 fuels at BARC. The Al-20% U alloy fuel for KAMINI neutron radiography reactor was prepared by 'melting and casting' route, followed by picture framing and roll-bonding. For higher 'U' density fuels namely, Al-UAlx, Al-U3O8 and Al-U3Si2 the 'powder metallurgy' route was followed for preparation of fuel meat. The novel features in fabrication route were: addition of Zr for stabilizing UAl3 phase in Al-20% U alloy; x-ray radiography and microdensitometric scanning of radiographs for location of fuel outline inside fuel element and for confirming homogeneous distribution of fissile atoms; immersion ultrasonic testing for confirming good bonding between mating Al surface of the fuel plate. (author)

  20. Analytical study, by modelling methods, of the alkali and alkaline earth cations influence on the stability and the reactivity of aluminium (III) oxides or halides complexes; Etude analytique, par des techniques de modelisation, de l`influence de cations alcalins ou alcalino-terreux sur la stabilite et la reactivite de complexes de l`aluminium(III) avec des ions halogenures ou oxydes

    Energy Technology Data Exchange (ETDEWEB)

    Bouyer, F.

    1995-10-05

    The electric power consumption in aluminium production and electrorefining processes is high. A study of the electrochemical processes can be very useful for a better understanding of phenomena in electrolytic baths and then for reducing the production costs. A structural and vibrational analysis of species which exist in ionic solutions has been carried out with software based on the functional density theory. Concerning the electrolyte used for the aluminium refining, the anions study has shown that the aluminium chloro-fluoride complexes are preferentially tetrahedral. Moreover, the aluminium oxyfluoride complexes structures (which come from the alumina dissolution in cryolitic media) have been analyzed in the same way and the preferential coordination numbers for aluminium and oxygen have been shown clearly. The anionic model (which is limited to the nearest aluminium neighbours) does not allow to account for the thermodynamics of the cryolitic media. A more elaborated model has then been found to obtain the cryolite structure. The reactions enthalpies have been estimated and have lead to the calculus of species concentration gradients in liquid phase. The counterions effects as for instance sodium and calcium have been investigated. A model for the gaseous phase allowing to know the preferential species has been given. At last, a statistic thermochemistry program has been conceived and developed. It gives the thermodynamical functions at all temperature for the different complexes and allows to reckon the reactions coefficients in gaseous phase as well as the partial pressures profiles with those of calcium and sodium fluorides. (O.M.) 204 refs.

  1. The Optimization of Salt Additions during Processing of Aluminium-Magnesium Alloys

    OpenAIRE

    Solberg, Egil

    2013-01-01

    Sodium is well known to be a cause for edge cracking during rolling of aluminium-magnesium alloys (AA5xxx). Due to this, requirements for the sodium contents in Al-Mg alloys are often less than 1,0 ppm. The electrolytic produced aluminium have a sodium content in the range of 30 to 200 ppm, where the highest levels are present in the most modern pot lines.To reduce sodium and other impurities like oxides and carbides several techniques are available for casthouses today. Furnace fluxing and d...

  2. The General Situation of the Scale and Layout of Aluminium Industry in China

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>Since 2002, aluminium industry has become a key industry under the macro control of the country, for which the reason is the aluminium industry in China has seen "repeated construc-tion", "blind investment", "excessive capacity",

  3. PREDICTION OF PLASTIC ANISOTROPY IN ALUMINIUM EXTRUDED TUBES BY FINITE ELEMENT POLYCRYSTAL MODEL

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Numerical simulation of extrusion process of aluminium tube is dealt with using the finite element polycrystal model. The non-uniformity in plastic anisotropies of aluminium extruded tubes through the wall thickness is investigated.

  4. Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

    Directory of Open Access Journals (Sweden)

    Mathivanan Periasamy

    2012-06-01

    Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

  5. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    OpenAIRE

    Polus Łukasz; Szumigała Maciej

    2015-01-01

    In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally f...

  6. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    OpenAIRE

    Zauzi, N. S. Ahmad; M. Z. H. Zakaria; Baini, R.; Rahman, M. R.; N. Mohamed Sutan; Hamdan, S

    2016-01-01

    Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH) on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipita...

  7. The determination of boron in high-purity aluminium metal by spark-source mass spectrometry

    International Nuclear Information System (INIS)

    A method is described for the determination of boron in high-purity aluminium metal. Both isotopic boron lines (10B+1 and 11B+1) are used for the analysis. As there are no low-abundance isotopic lines for aluminium, measurements were made direct without reference to aluminium as an internal standard. The boron concentration values of eight aluminium samples analysed by this method compared favourably with results obtained from other techniques

  8. Low Speed Laser Welding of Aluminium Alloys Using Single-Mode Fiber Lasers

    OpenAIRE

    Tu, Jay; Paleocrassas, Alexander

    2010-01-01

    In this chapter, topics related to extending fiber laser welding of aluminium in the low speed range were discussed. General topics, such as the properties of aluminium and welding defects, review of high speed laser welding of aluminium, and fiber laser characteristics and optical setups for safety, were first reviewed. Recent research results on the modelling and validation of laser welding of aluminium, experimental characterization of low speed welding processes, and the instability pheno...

  9. Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

    Science.gov (United States)

    Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

    2011-11-01

    The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling. PMID:21274747

  10. Natural gas anodes for aluminium electrolysis in molten fluorides.

    Science.gov (United States)

    Haarberg, Geir Martin; Khalaghi, Babak; Mokkelbost, Tommy

    2016-08-15

    Industrial primary production of aluminium has been developed and improved over more than 100 years. The molten salt electrolysis process is still suffering from low energy efficiency and considerable emissions of greenhouse gases (CO2 and PFC). A new concept has been suggested where methane is supplied through the anode so that the CO2 emissions may be reduced significantly, the PFC emissions may be eliminated and the energy consumption may decrease significantly. Porous carbon anodes made from different graphite grades were studied in controlled laboratory experiments. The anode potential, the anode carbon consumption and the level of HF gas above the electrolyte were measured during electrolysis. In some cases it was found that the methane oxidation was effectively participating in the anode process. PMID:27210046

  11. An unconventional set-up for fluxless brazing of aluminium

    CERN Document Server

    Loos, Robert

    1999-01-01

    In order to successfully braze aluminium alloy assemblies without the use of oxide-removing fluxes, an evironment with very low contaminant level is mandatory. This is mostly achieved by using a vacuum furnace. Brazing under inert gas of sufficient purity is also possible. The method reported upon here makes use of a stainless steel bag which can enter a traditional air furnace. The bag is evacuated, giving a well distributed mechanical pressure on the parts to join. The intrinsic handicap of poor vacuum is compensated by regular inert gas flushing, even at high temperatures. The set-up works rather well, and the idea is believed to yield a valuable strategic and economic option, for the realization of special equipment as well as for prototyping work. We intend to use the principle for the CMS Preshower cooling screens.

  12. Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

    NARCIS (Netherlands)

    Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

    2012-01-01

    Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide p

  13. The Prospect of China’s Alumin-ium Extrusion Product Market

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>China’s aluminium extrusion industry can be dated back to the 1950s-70s,when the North- east 101 Plant was established in 1956,the Northwest Aluminium and Southwest Alumin- ium were completed and put into operation in 1968-1969.The three plants’ extrusion assem- bly lines were designed to produce aluminium

  14. The Net Exporting Trends Remains for China’s Aluminium Products

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The oversupply of China’s raw aluminium has caused the continuing net exporting for China’s aluminium products.As the situation is wors- ened due to the growing raw aluminium pro- duction and curbed demand,it is estimated that the continuation of net exporting of China’s

  15. Bakable aluminium vacuum chamber and bellows with an aluminum flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber and bellows (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the assemblies of the vacuum chambers in proton synchrotrons and electron storage rings

  16. Energy efficiency improvement and GHG abatement in the global production of primary aluminium

    NARCIS (Netherlands)

    Kermeli, Katerina; Ter Weer, Peter Hans; Crijns - Graus, Wina; Worrell, Ernst

    2015-01-01

    Primary aluminium production is a highly energy-intensive and greenhouse gas (GHG)-emitting process responsible for about 1 % of global GHG emissions. In 2009, the two most energy-intensive processes in primary aluminium production, alumina refining and aluminium smelting consumed 3.1 EJ, of which 2

  17. PEMBINAAN PENGERAJIN BOKOR ALUMINIUM DI DESA MENYALI

    Directory of Open Access Journals (Sweden)

    I NYOMAN GDE ANTARA, dkk.

    2014-04-01

    Full Text Available Alluminium bowl craft industrial center is located in Menyali village Sawan district Buleleng regency of Bali province. In this business development, they faced some problems such as increasingly expensive alluminium plate raw materials, decreasing selling product prices due to competition among craftsmen, difficulty in extending the marketing, lack of capital, lack of knowledge in business management, and lack of technical capacity and production innovation. Currently the organization has been formed aluminum bowl craftsmen groups, they are “Sumber Urip” and “Sumur Jaya”. This organization is still limited to tradisional associations such as a community organization, has not led to organize in a micro-enterprise or cooperation. Their organization management should not be arranged. Therefore, they need helps from the government and other institutions to build this bowl craftsmen in developing their businesses through a group of micro-enterprises or cooperations. Wishly, with formal business entity that would facilitate access to a variety of coaching and help governments andother institutions. From the SWOT analysis, it is found some problems and solutions that should be done. Alluminium bowl craftsmen groups, named “Sumber Urip” and “Sumur Jaya” is not in the form of business entity or cooperation yet, so that the results of coaching have agreed to form a cooperation. Venture capital assistance for the development and production are still needed and to be an absolute given, but a way to market more absolute yield is given, through participation in various events exhibition to introduce the product is expected to expandits market share up to overseas or exports. In the production process it has been introduced that is appropriate technology for instant a rolling tool to make a wiring groove on the outside of the bowl, so that it will simplify and speed up the process, especially by aged mothers.Keywords: aluminium bowl, Menyali

  18. Residual stress in 7449 aluminium alloy forgings

    International Nuclear Information System (INIS)

    The through thickness residual stress distributions within three 120 mm thick rectilinear forgings, made from the high strength aluminium alloy 7449 have been measured using both neutron diffraction and deep hole drilling. Neutron diffraction measurements were made on two instruments, one using a pulsed spallation neutron source, the other a steady state reactor source. Heat treatment of the forgings included a rapid quench into cold water and it was the residual stresses arising from this step that were initially measured. Neutron diffraction measurements indicated large magnitude (>250 MPa) tensile residual stresses in the centre of an as quenched forging, balanced by surface regions stressed in compression (<-200 MPa). Sufficient measurements were made to permit the description of the residual stress distribution using area maps. Two forgings were stress relieved by cold compression immediately after quenching. The degree of plastic strain was either 2.5% or 4%, and was applied by a single application of force in the short transverse direction. Cold compressed forgings were found to have far lower residual stress when compared to the as quenched condition. The amount of cold compression was found to cause an insignificant difference in the final residual stress distribution. The neutron diffraction results are compared to measurements made by deep hole drilling and a new incremental variation of the technique. The deep hole was drilled through the centre of the forgings in the short transverse direction. Multiple neutron diffraction measurements were also made on the extracted cores from the deep hole measurements to assess the variation of the unstrained lattice parameter through the thickness of the forgings.

  19. Aluminium supplier selection for the automotive parts manufacturer

    Directory of Open Access Journals (Sweden)

    M. Cieśla

    2016-04-01

    Full Text Available This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method and a graphical method. Choosing the best offer and prioritizing suppliers allows not only the most rational decision in the field of supply logistics to be taken but also the quality of service in the metallurgical industry to be improved.

  20. [Photophysical properties and photodynamic activity of nanostructured aluminium phthalocyanines].

    Science.gov (United States)

    Udartseva, O O; Lobanov, A V; Andeeva, E R; Dmitrieva, G S; Mel'nikov, M Ia; Buravkova, L B

    2014-01-01

    We developed water-soluble supramolecular complexes of aluminium phthalocyanine based on mesoporous silica nanoparticles and polyvinylpirrolidone containing rare photoactive nanoaggregates. Radiative lifetimes, extinction coefficients and energy of electronic transitions of isolated and associated metal phthalocyanine complexes were calculated. Nontoxic concentrations of synthesized nanocomposite photosensibilizers were in vitro determined. In present study we compared photodynamic treatment efficacy using different modifications of aluminium phthalocyanine (Photosens®, AlPc-nSiO2 and AlPc-PVP). Mesenchymal stromal cells were used as a model for photodynamic treatment. Intracellular accumulation of aluminium phthalocyanine based on mesoporous silica nanoparticles AlPc-nSiO2 was the most efficient. Illumination of phthalocyanine-loaded cells led to reactive oxygen species generation and subsequent apoptotic cell death. Silica nanoparticles provided a significant decrease of effective phthalocyanine concentration and enhanced cytotoxicity of photodynamic treatment.

  1. Reflection of infrared radiation from thin aluminium layers

    CERN Document Server

    Calatroni, Sergio

    2001-01-01

    The thermal shielding of the LHC magnets cryostats will make use of Multi-Layer Insulation. This is a sandwich of several Mylar (polyester) foils 6 µm thick coated with a thin film of aluminium, having a thickness of some 30 nm. The thickness of the aluminium film must be kept at a minimum to minimise lateral thermal conduction. The outer layer of this sandwich stays at a temperature of 20 K or below, and receives IR radiation from surfaces at 77 K (wavelength of 37.6 µm at the peak of blackbody radiation), which should be reflected with the highest efficiency. The minimum thickness for the aluminium layer to avoid transmission of the radiation can be calculated by making use of the skin effect theory, taking into account the changes in electrical properties that are due to the extremely low thickness of the film.

  2. Langmuir-Blodgett Films from Schiff Base Aluminium ( Ⅲ ) Complex

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The characteristics of the LB films of Schiff base aluminium( Ⅲ ), tris(2-hydroxy-5-nitro N-dodecyl-benzylideneaminato) aluminium ( Ⅲ ) [Al (TA 12) 3], were studied. The surface pres sure-area(r-A) isotherm of Al(TA12)3 in the pure water subphase was investigated. The molec ular area, 0.48 nm2, is one-third of the expected value that indicates the formation of an aggre gate. The Langmuir-Blodgett (LB) films of Al(TA12) 3 were transferred and characterized. The UV-Vis spectra and the AFM image both confirmed that the J-aggregates formed. The polarized UV-Vis spectra indicated that the complex plane had to be oriented with an angle of about 30° to the substrate surface. The IR spectra suggested that the complexation took place between aluminium ions and the oxygen atoms of the ligand rather than the nitrogen atom.

  3. Aluminium toxicity in the rat liver and brain

    International Nuclear Information System (INIS)

    To investigate the etiology of Alzheimer's disease, we examined the brain and liver tissue uptake of aluminium 5-75 days after aluminium injection into healthy rats. Ten days after the last injection, Al was detected in the brain and the brain cell nuclei by particle-induced X-ray emission (PIXE) analysis. Al was also demonstrated in the liver and the liver cell nuclei by PIXE analysis and electron energy loss spectrometry (EELS). The morphological changes of the rat brain examined 75 days after the injection were similar to those which have been reportedly observed in the brain of patients with Alzheimer's disease. These results support the theory that Alzheimer's disease is caused by irreversible accumulation of aluminium in the brain, as well as the nuclei of brain cells. (orig.)

  4. Constitutive modelling of aluminium alloy sheet at warm forming temperatures

    Science.gov (United States)

    Kurukuri, S.; Worswick, M. J.; Winkler, S.

    2016-08-01

    The formability of aluminium alloy sheet can be greatly improved by warm forming. However predicting constitutive behaviour under warm forming conditions is a challenge for aluminium alloys due to strong, coupled temperature- and rate-sensitivity. In this work, uniaxial tensile characterization of 0.5 mm thick fully annealed aluminium alloy brazing sheet, widely used in the fabrication of automotive heat exchanger components, is performed at various temperatures (25 to 250 °C) and strain rates (0.002 and 0.02 s-1). In order to capture the observed rate- and temperature-dependent work hardening behaviour, a phenomenological extended-Nadai model and the physically based (i) Bergstrom and (ii) Nes models are considered and compared. It is demonstrated that the Nes model is able to accurately describe the flow stress of AA3003 sheet at different temperatures, strain rates and instantaneous strain rate jumps.

  5. Pressureless sintered silicon carbide tailored with aluminium nitride sintering agent

    International Nuclear Information System (INIS)

    This study reports the influence of aluminium nitride on the pressureless sintering of cubic phase silicon carbide nanoparticles (β-SiC). Pressureless sintering was achieved at 2000 degrees C for 5 min with the additions of boron carbide together with carbon of 1 wt% and 6 wt%, respectively, and a content of aluminium nitride between 0 and 10 wt%. Sintered samples present relative densities higher than 92%. The sintered microstructure was found to be greatly modified by the introduction of aluminium nitride, which reflects the influence of nitrogen on the β-SiC to α-SiC transformation. The toughness of sintered sample was not modified by AlN incorporation and is relatively low (around 2.5 MPa m1/2). Materials exhibited transgranular fracture mode, indicating a strong bonding between SiC grains. (authors)

  6. Washery tailings from coal preparation used as aluminium feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Kuehn, L.; Schieder, T.; Belsky, M.; Lotze, J.; Winkhaus, G.

    1982-06-01

    Kaolinite clays and washery tailings of coal mines are the major feedstocks of the West German aluminium industry. Statistics are given in order to assess the amount of washery tailings available and their suitability as feedstocks for aluminium production. The chemical and mineralogical composition are similar for washery tailings from different mines; accordingly, also their behaviour regarding decomposition by acids will be almost identical. Al/sub 2/O/sub 3/ extraction yields are satisfactory with strongly precalcinated material using concentrated sulphuric acid or azeotropic hydrochloric acid - in the latter case, however, only if fluoride is added to the acid.

  7. Aging of maraging steel welds during aluminium alloy die casting

    OpenAIRE

    Klobčar, Damjan; Pleterski, Matej; Taljat, Boštjan; Kosec, Ladislav; Tušek, Janez

    2015-01-01

    The aim of this study is to evaluate precipitation annealing of 18% Ni maraging steel repair welds during aluminium die casting and to predict the prolonged in-service tool life. The emphasis of this study is the influence ofpost-weld precipitation annealing heat treatment and aluminium die casting thermal cycling on metallurgical and mechanical properties. A series of specimens of 1.2344 tool steel is prepared to which 1.6356 maraging steel is GTA weld cladded. Analysis of weld microstructur...

  8. Finite size melting of spherical solid-liquid aluminium interfaces

    DEFF Research Database (Denmark)

    Chang, J.; Johnson, Erik; Sakai, T.;

    2009-01-01

    We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting...... to the conclusion that the depressed melting temperature is not controlled solely by the inverse radius 1/R. Instead, we found a direct relation between the depressed melting temperature and the ratio between the solid-liquid interface area and the molten volume....

  9. Aluminium Price Looks Down Due To Increased Capacities

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>Speaking at a recent forum on China’S alumin- ium industry,Wen Xianjun,director of the aluminium branch under China Nonferrous Metals Industry Association,said that the alu- minium price in 2007 looks going downward due to the production capacity expansion out of the high market price last year.He estimates that the downward development of the alumin- ium price in China will be more obvious than that in the rest part of the world.He predicts that in 2007 the average aluminium price in

  10. Power quality results in energy efficient aluminium smelter operation

    Energy Technology Data Exchange (ETDEWEB)

    Wiestner, Max

    2010-09-15

    New aluminium smelters consume up to 2400MW of electrical energy making the energy efficiency aspect most important. Power quality, optimised power conversion systems and well engineered power plant interfaces are essential for highest energy efficiency. An early optimisation of the power system design will reduce the capital investment cost for the power plant and smelter substation as well as results in most energy efficient aluminium production. This paper describes and intends to discuss the power quality improvement concepts and designs as well as energy cost reduction opportunities which a high power quality system can achieve.

  11. The hydrolysis of aluminium, a mass spectrometric study

    OpenAIRE

    Sarpola, A.

    2007-01-01

    Abstract This thesis is focused on the hydrolysis of aluminium, the polymerisation of the hydrolysis products, and how these can be monitored by mass spectrometric methods. The main aim of this research is to figure out how the aqueous speciation of aluminium changes as a function of pH (3.2–10), concentration (1–100 mM), reaction time (1s–14d), and counter anion (Cl-, SO42-, HCOO-). The method used was electrospray mass spectrometry. The results showed more variable speciation than those ...

  12. Research of Properties of Sprayed Coatings on the Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    Raimonda Lukauskaitė

    2014-02-01

    Full Text Available In article the cathodic cleaning processes of aluminum alloyAW 5754 and cleaned substrate surface coating by plasmawith Ni-Cr-Fe-Si powder were researched. Aluminium substrateroughness after cathodic treatment at different cathodic treatmentparameters was established during the experiments. During theinvestigation a comparison of the calculated medium power1.6 to 9 kW plasma torch voltage-current characteristics withthe experimental results was made. The optimized parametersof aluminium cathode substrate cleaning process were selected;porosity and morphology of plasma sprayed nickel-based coatingwere determined.

  13. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    Directory of Open Access Journals (Sweden)

    Napachat Tareelap

    2014-03-01

    Full Text Available Due to the failure of manganese aluminium bronze (MAB propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium in seawater to form calcium carbonate film protecting the propeller from corrosion.

  14. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    International Nuclear Information System (INIS)

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg (AlMg3) and Al-1.1%Mg-0.5%Si (Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-1000C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) showed a complete absence of voids or bubbles in the grain interiors of the aluminium and the aluminium-alloys. Bubbles were clearly visible by TEM at grain boundaries in pure Al and the AlMg3 alloy; but bubbles were not visible in the Al6061 alloy. The bubble density in the AlMg3 alloy was considerably higher than in pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure. (orig.)

  15. Carbon treated commercial aluminium alloys as anodes for aluminium-air batteries in sodium chloride electrolyte

    Science.gov (United States)

    Pino, M.; Herranz, D.; Chacón, J.; Fatás, E.; Ocón, P.

    2016-09-01

    An easy treatment based in carbon layer deposition into aluminium alloys is presented to enhance the performance of Al-air primary batteries with neutral pH electrolyte. The jellification of aluminate in the anode surface is described and avoided by the carbon covering. Treated commercial Al alloys namely Al1085 and Al7475 are tested as anodes achieving specific capacities above 1.2 Ah g-1vs 0.5 Ah g-1 without carbon covering. The influence of the binder proportion in the treatment as well as different carbonaceous materials, Carbon Black, Graphene and Pyrolytic Graphite are evaluated as candidates for the covering. Current densities of 1-10 mA cm-2 are measured and the influence of the alloy explored. A final battery design of 4 cells in series is presented for discharges with a voltage plateau of 2 V and 1 Wh g-1 energy density.

  16. Laser beam welding of high strength aluminium-lithium alloys; Laserstrahlschweissen von hochfesten Aluminium-Lithium Legierungen

    Energy Technology Data Exchange (ETDEWEB)

    Enz, Josephin

    2012-07-01

    The present development in aircraft industry determined by the demand for a higher cost-effectiveness. Laser beam welding is one of the most promising joining technologies for the application in the aircraft industry through the considerable reduction of the production costs. Furthermore the weight of an aircraft structure can be reduced by the use of light and high strength aluminium alloys. This paper deals with the development of a process for the laser beam welding of a skin-stringer-joint where the Al-Li-alloy AA2196 is used as stringer material and the Al-Li-alloy AA2198 is used as skin and stringer material. By the use of design of experiments the optimal welding process parameters for different material combinations were determined which will be used for the welding of a 5-stringer panel. Therefore the weld seams of the joints were tested for irregularities and microstructural characteristics. In addition several mechanical tests were performed, which define the quality of the welded joint. Furthermore the influence of the oxide layer and the welding preparation on the welding performance was investigated. (orig.) [German] Die derzeitigen Entwicklungen im Flugzeugbau werden durch die allgemeine Forderung nach einer Steigerung der Wirtschaftlichkeit bestimmt. Das Laserstrahlschweissen ist dabei eines der vielversprechendsten Fuegeverfahren fuer die Anwendung im Flugzeugbau durch das die Herstellungskosten deutlich reduziert werden koennen. Zudem kann durch die Verwendung von leichten und hochfesten Aluminium-Legierungen das Gewicht einer Flugzeugstruktur zusaetzlich reduziert werden. Die vorliegende Arbeit befasst sich mit der Entwicklung eines Prozesses zum Laserstrahlschweissen einer Skin-Stringer-Verbindung aus den Aluminium-Lithium-Legierungen AA2196 (als Stringer-Werkstoff) und AA2198 (als Skin- und Stringer-Werkstoff). Unter Verwendung der statistischen Versuchsplanung wurden die optimalen Einstellungen der Schweissprozessparameter fuer die

  17. New Investment Rush Brings up Concern for China’s Aluminium Industry

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> Although the blind construction of the electro-lytic aluminium industry has been restricted inChina this year,an investment rush in aluminaand aluminium processing has started,whichhas brought up new concern for the industry.Whether this will follow the route of the much-heated electrolytic aluminium industry remainsa question to be answered.According to someindustry analysts,under the pressure of themacro control measures of the State on theelectrolytic aluminium industry expansion,some producers of aluminium have shiftedtheir interests to the upper and lower fields soas to raise their competitiveness over the mar-

  18. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    Science.gov (United States)

    Polus, Łukasz; Szumigała, Maciej

    2015-03-01

    In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  19. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    Directory of Open Access Journals (Sweden)

    Polus Łukasz

    2015-03-01

    Full Text Available In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  20. Energy response of an aluminium oxide detector in kilo-voltage and mega-voltage photon beams: An EGSnrc Monte Carlo simulation study

    International Nuclear Information System (INIS)

    A Monte Carlo study of the energy response of an aluminium oxide (Al2O3) detector in kilo-voltage and mega-voltage photon beams relative to 60Co gamma rays has been performed using EGSnrc Monte Carlo simulations. The sensitive volume of the Al2O3 detector was simulated as a disc of diameter 2.85 mm and thickness 1 mm. The phantom material was water and the irradiation depth chosen was 2.0 cm in kilo-voltage photon beams and 5.0 cm in mega-voltage photon beams. The results show that the energy response of the Al2O3 detector is constant within 3% for photon beam energies in the energy range of 60 Co gamma rays to 25 MV X-rays. However, the Al2O3 detector shows an enhanced energy response for kilo-voltage photon beams, which in the case of 50 kV X-rays is 3.2 times higher than that for 60Co gamma rays. There is essentially no difference in the energy responses of LiF and Al2O3 detectors irradiated in mega-voltage photon beams when these Al2O3 results are compared with literature data for LiF thermoluminescence detectors. However, the Al2O3 detector has a much higher enhanced response compared with LiF detectors in kilo-voltage X-ray beams, more than twice as much for the case of 50 kV X-rays. (authors)

  1. Fundamental studies of growth mechanisms in physical vapour deposition of aluminium

    CERN Document Server

    Knorr, N J

    2000-01-01

    temperature could be independently controlled due to the low deposition rate of the aluminium. The depositions were performed in a UHV environment to ensure that film growth was not mediated by contamination. The ion energy range used was 10-75eV and the substrate temperature varied from -100 deg C to 200 deg C. The depositions were onto silicon (100) with a native oxide surface, except for a set of depositions which were performed on to silicon with the native oxide surface removed. The cleanliness of the depositions was verified using in-situ XPS analysis and after deposition the structure of the aluminium films was inferred from measurements using SEM, TEM, AFM XRD and Nano-indendation. This information allowed the mechanisms of growth of the aluminium films to be investigated. In addition to the extensive array of IBDR depositions a series of aluminium films were deposited using evaporation and sputtering. These films were grown at substrate temperatures between room temperate and 200 deg C. The use of ev...

  2. Remelting of Aluminium by Continuous Submersion of Rolled Scrap

    Energy Technology Data Exchange (ETDEWEB)

    Farner, Snorre

    2000-12-01

    When remelting aluminium scrap, metal losses due to dross generation is a common problem. Reduction of these losses will give substantial economic and environmental benefits. Dross is generated when aluminium metal oxidizes and films of oxide envelope molten metal. When a cold metal object is immersed in a melt, the heat of the melt around this is transferred so rapidly into the object that a shell of melt often solidifies to the surface of the object. When scrap with low bulk density is charged to a melt, solidification of melt on the cold scrap prevents melt from entering the cavities in the bulk of the scrap, and the bulk density remains low. Thus the scrap tends to float on the melt surface. Submersion of this scrap is important to avoid oxidation and subsequent dross generation. One solution to this is to roll scrap to a strip and feed it into the melt. This system has been examined by studying feeding of a continuous, thin aluminium plate into molten aluminium. Also, the effect of lacquer was considered, as well as feeding the plate into a launder with melt flowing along the surface of the plate. An analytical, one-dimensional, steady-state model has been developed to describe the melting and the melting mechanisms. It is based on a shell solidifying on the plate surface and a gap introducing a thermal resistance 1/h{sub g} between the shell and the plate. The thermal resistance 1/h{sub l} of the boundary layer of the melt is included. Depending on these resistances, the initial temperature of the plate and the melt temperature, a shell will form, and the plate will penetrate a distance P into the melt before it melts away. An experimental apparatus was designed and constructed to feed aluminium plate from a coil into a melt bath at a specified velocity. The plate could be withdrawn rapidly to ''freeze'' the situation like it was below the melt surface. The penetration depth P of the plate could be measured and shell formation observed

  3. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid;

    2014-01-01

    of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...

  4. Cold forming of aluminium - State of the art

    DEFF Research Database (Denmark)

    Bay, Niels

    1997-01-01

    The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable to that of unal...... Elsevier Science S.A....

  5. STRUCTURE OF ECAP ALUMINIUM AFTER DIFFERENT NUMBER OF PASSES

    Directory of Open Access Journals (Sweden)

    Lucia Ilucová

    2011-05-01

    Full Text Available The structure of high purity (99.99% aluminium processed by equal channel angular pressing in the as pressed state after different number of passes was examined using various stereological methods. An extreme inhomogeneity and complicated anisotropy was observed along the body of rod-like specimens.

  6. Zonal distribution of dissolved aluminium in the Mediterranean Sea

    NARCIS (Netherlands)

    Rolison, J. M.; Middag, R.; Stirling, C. H.; Rijkenberg, M. J. A.; de Baar, H. J. W.

    2015-01-01

    Dissolved aluminium (Al) is an important tracer of atmospheric dust input to the oceans. The GEOTRACES expedition to the highly dust impacted Mediterranean Sea afforded the opportunity to study the distribution of dissolved Al in the Mediterranean Sea in detail. Interestingly, the elevated concentra

  7. Development of an aluminium stabilized reinforced superconducting conductor

    Energy Technology Data Exchange (ETDEWEB)

    Fritz, D. [PTR Praezisionstechnik GmbH Maintal (Germany); Horvath, I.L. [Swiss Federal Inst. of Tech., Zuerich (Switzerland); Harzenmoser, M.; Neuenschwander, J. [Swiss Federal Labs. for Materials Testing and Research, Duebendorf (Switzerland); Wittgenstein, F. [CERN, Geneva (Switzerland)

    1996-07-01

    For high performance superconducting magnets as used in large detectors for the High Energy Physics or for magnets of magnetic storage devices (SMES) the mechanical stresses on the conductor go beyond the yield stress level of the high purity matrix stabilizer, specially if aluminium is used. Therefore, a novel method is proposed to join high strength aluminium strips to high purity aluminium stabilizer by using the electron beam (EB) welding. The proposed EB-welding, combined with roll-pressing under vacuum, provides the minimum heat input on the conductor in comparison with other welding techniques. This method provides the advantage to allow the production of very long conductor lengths and includes the potentiality of repairing without losing expensive material. As this process has to be adapted to the high purity aluminium on the one side and to the high strength material on the other, the authors started in a first step with investigation and development of the process, using standard laboratory machines together with laboratory-size tooling. In this report the development program is described and first results of the quality control measurements are presented.

  8. Molecular Characterization of Aluminium (aluminum) Tolerance in Rye

    Science.gov (United States)

    Aluminium (Al) toxicity, affecting around half of the world’s arable land, severely hinders the ability of crop plants to utilize moisture and nutrients by restricting root growth and function. Among the cultivated cereals, rye is the most Al-tolerant and represents an important potential source of ...

  9. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    Science.gov (United States)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  10. Silicon Carbide Tiles for Sidewall Lining in Aluminium Electrolysis Cells

    Institute of Scientific and Technical Information of China (English)

    RUANBo; ZHAOJunguo; 等

    1999-01-01

    The paper introduces the nitride bonded silicon carbide used for sidewall lining in aluminium eletrolysis cells ,including technical process,main properties and application results.Comparison tests on various physical properties of silicon carbide products made by LIRR and other producers worldwide have also been conducted in an independent laboratory.

  11. Local electrochemical behaviour of 7xxx aluminium alloys

    NARCIS (Netherlands)

    Andreatta, F.

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a neg

  12. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    Science.gov (United States)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-09-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN.

  13. Mechanochemical route to the synthesis of nanostructured Aluminium nitride.

    Science.gov (United States)

    Rounaghi, S A; Eshghi, H; Scudino, S; Vyalikh, A; Vanpoucke, D E P; Gruner, W; Oswald, S; Kiani Rashid, A R; Samadi Khoshkhoo, M; Scheler, U; Eckert, J

    2016-09-21

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN.

  14. Mechanochemical route to the synthesis of nanostructured Aluminium nitride.

    Science.gov (United States)

    Rounaghi, S A; Eshghi, H; Scudino, S; Vyalikh, A; Vanpoucke, D E P; Gruner, W; Oswald, S; Kiani Rashid, A R; Samadi Khoshkhoo, M; Scheler, U; Eckert, J

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  15. A vector valued Stefan problem from aluminium industry

    NARCIS (Netherlands)

    Vermolen, F.J.; Vuik, C.

    1998-01-01

    Dissolution of stoichiometric multi-component particles in ternary alloys is an important process occurring during the heat treatment of as-cast aluminium alloys prior to hot-extrusion. A mathematical model is proposed to describe such a process. In this model an equation is given to determine the p

  16. Modelling of aluminium sheet material at elevated temperatures

    NARCIS (Netherlands)

    Haaren, L.; Boogaard, van den A.H.; Huetink, J.

    2004-01-01

    The formability of Al–Mg sheet can be improved considerably, by increasing the temperature. At elevated temperatures, the mechanical response of the material becomes strain rate dependent. To accurately simulate warm forming of aluminium sheet, a material model is required that incorporates the temp

  17. Modelling of contact and friction in aluminium extrusion

    NARCIS (Netherlands)

    Ma, X.; Rooij, de M.B.; Schipper, D.J.

    2010-01-01

    A physical model capable of predicting the friction and sticking/slipping lengths in the bearing channel during unlubricated aluminium extrusion processes is presented. The model takes into account the pressure build up in the extrusion direction in relation with the bearing–extrudate friction and h

  18. Modelling aluminium wire bond reliability in high power OMP devices

    NARCIS (Netherlands)

    Kregting, R.; Yuan, C.A.; Xiao, A.; Bruijn, F. de

    2011-01-01

    In a RF power application such as the OMP, the wires are subjected to high current (because of the high power) and high temperature (because of the heat from IC and joule-heating from the wire itself). Moreover, the wire shape is essential to the RF performance. Hence, the aluminium wire is preferre

  19. Modelling of friction for high temperature extrusion of aluminium alloys

    NARCIS (Netherlands)

    Wang, L.

    2012-01-01

    In recent years, finite-element (FE) simulations have been extensively used in scientific research and industrial practice to analyse the extrusion process. A basic issue of FE simulations is the accuracy of the results, which is mainly determined by the viscoplastic material behaviour of aluminium

  20. Hydrogen evolution from aluminium in reactor containment spray solutions

    International Nuclear Information System (INIS)

    Three different aluminium alloys were exposed to conditions similar to BWR and PWR containment spray waters at 50, 100 and 1500C. BWR deionized water gives corrosion rates of at most 0.05 mm/year and hydrogen concentrations less than 0.1-1%. On the contrary PWR alkaline solutions give very high corrosion rates and hydrogen contents. (Auth.)

  1. Establishment of Integrated Information Displays in Aluminium Surfaces Using Nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan Phuklin; Bladt, Henrik Henriksen; Hansen, Hans Nørgaard

    2005-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in Aluminium that can be penetrated by light. This has resulted in a patent describing how to obtain this effect by etching of local areas in a solid material. The idea behind an invisible display in Aluminum co...... ultra-short pulses, selective etching + anodizing, and electrochemical machining....

  2. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  3. Waste treatment of fission product solutions containing aluminium nitrate

    International Nuclear Information System (INIS)

    In the Rossendorf molybdenum-99 production facility AMOR short-term irradiated aluminium clad fuel elements from the Rossendorf Research Reactor are reprocessed. Following extractive recovery of the enriched uranium the facility system has to be disposed of the fission product-Al(NO3)3 solution. Investigations on waste conditioning of such solutions are presented. (author)

  4. Hydrogen generation from aluminium corrosion in reactor containment spray solutions

    International Nuclear Information System (INIS)

    The aluminium corrosion experiments in reactor containment spray solutions, under the conditions expected to prevail during LOCA in BWR and PWR, were performed in order to investigate relationships between temperature, pH and hydrogen production rates. In order to simulate the conditions in a BWR containment realistic ratios between aluminium surface and water volume and between aluminium surface and oxygen volume were used. Three different aluminium alloys were exposed to spray solutions: AA 1050, AA 5052 and AA 6082. The corrosion rates were measured for BWR solutions (deaerated and aerated) with pH 5 and 9 at 50, 100 and 1500C. The pressure was constantly 0.8 MPa. The hydrogen production rate was measured by means of gas chromatography. In deionized BWR water the corrosion rates did not exceed about 0.05 mm/year in all cases, i.e. were practically independent of temperature and pH. Hydrogen concentrations were less than 0.1 vol.% in cooled dry gas. Corrosion rates and hydrogen production in PWR alkaline solution measured at pH 9.7 and 1500C were very high. AA 5052 alloy was the best material

  5. Electrochemical Characterisation of Filiform Corrosion on Aluminium Rolled Products

    NARCIS (Netherlands)

    Huisert, M.

    2001-01-01

    When aluminium is protected by an organic coating a special form of corrosion can occur underneath the organic coating; filiform corrosion. This form of corrosion manifests itself as threadlike filaments under the coating, it causes local delamination of the coating and the coating cannot protect th

  6. Cavitation-aided grain refinement in aluminium alloys

    NARCIS (Netherlands)

    Atamanenko, T.V.

    2010-01-01

    This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the conditi

  7. Effects of Aluminium in Forest. Results of a pilot experiment

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, J.; Wit, H. de; Nygaard, P.H.

    1996-01-01

    This conference paper deals with an Norwegian pilot project which started in 1995 and finishing early 1999, investigates the solubility and phyto-toxicity of aluminium (Al) in mature forest ecosystems. The project consists of three major parts, including field manipulation study of Norwegian spruce stands, laboratory experiments and modelling Al chemistry in the root zone. 15 refs.

  8. Experimental weathering rates of aluminium silicates

    International Nuclear Information System (INIS)

    The chemical weathering of primary rocks and minerals in natural systems has a major impact on soil development and its composition. Chemical weathering is driven to a large extent by mineral dissolution. Through mineral dissolution, elements are released into groundwater and can readily react to precipitate secondary minerals such as clays, zeolites, and carbonates. Carbonates form from divalent cations (e.g. Ca, Fe and Mg) and CO2, and kaolin clay and gibbsite formation is attributed to the weathering of aluminium-rich minerals, most notably the feldspars. The CarbFix Project in Hellisheidi (SW-Iceland) aims to use natural weathering processes to form carbonate minerals by the re-injection of CO2 from a geothermal power plant back into surrounding basaltic rocks. This process is driven by the dissolution of basaltic rocks, rich in divalent cations, which can combine with injected CO2 to form and precipitate carbonates. This thesis focuses on the dissolution behaviour of Stapafell crystalline basalt, which consists of three major phases (plagioclase, pyroxene, and olivine) and is rich in divalent cations. Steady-state element release rates from crystalline basalt at far-from-equilibrium conditions were measured at pH from 2 to 11 and temperatures from 5 to 75 C in mixed-flow reactors. Steady-state Si and Ca release rates exhibit a U-shaped variation with pH, where rates decrease with increasing pH at acid condition but increase with increasing pH at alkaline conditions. Silicon release rates from crystalline basalt are comparable to Si release rates from basaltic glass of the same chemical composition at low pH and temperatures ≥25 C but slower at alkaline pH and temperatures ≥50 C. In contrast, Mg and Fe release rates decrease continuously with increasing pH at all temperatures. This behaviour is interpreted to stem from the contrasting dissolution behaviours of the three major minerals comprising the basalt: plagioclase, pyroxene, and olivine. Element

  9. Repassivation Investigations on Aluminium: Physical Chemistry of the Passive State

    Science.gov (United States)

    Nagy, Tristan Oliver; Weimerskirch, Morris Jhängi Joseph; Pacher, Ulrich; Kautek, Wolfgang

    2016-09-01

    We show the temporal change in repassivation mechanism as a time-dependent linear combination of a high-field model of oxide growth (HFM) and the point defect model (PDM). The observed switch in transient repassivation current-decrease under potentiostatic control occurs independently of the active electrode size and effective repassivation time for all applied overpotentials. For that, in situ depassivation of plasma electrolytically oxidized (PEO) coatings on aluminium was performed with nanosecond laser pulses at 266 nm and the repassivation current transients were recorded as a function of pulse number. A mathematical model combines the well established theories of oxide-film formation and growth kinetics, giving insight in the non linear transient behaviour of micro-defect passivation. According to our findings, the repassivation process can be described as a charge consumption via two concurrent channels. While the major current-decay at the very beginning of the fast healing oxide follows a point-defect type exponential damping, the HFM mechanism supersedes gradually, the longer the repassivation evolves. Furthermore, the material seems to reminisce former laser treatments via defects built-in during depassivation, leading to a higher charge contribution of the PDM mechanism at higher pulse numbers.

  10. Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

    Science.gov (United States)

    Kramer, Matthias F; Heath, Matthew D

    2014-07-16

    We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

  11. Aluminium and breast cancer: Sources of exposure, tissue measurements and mechanisms of toxicological actions on breast biology.

    Science.gov (United States)

    Darbre, Philippa D; Mannello, Ferdinando; Exley, Christopher

    2013-11-01

    This review examines recent evidence linking exposure to aluminium with the aetiology of breast cancer. The human population is exposed to aluminium throughout daily life including through diet, application of antiperspirants, use of antacids and vaccination. Aluminium has now been measured in a range of human breast structures at higher levels than in blood serum and experimental evidence suggests that the tissue concentrations measured have the potential to adversely influence breast epithelial cells including generation of genomic instability, induction of anchorage-independent proliferation and interference in oestrogen action. The presence of aluminium in the human breast may also alter the breast microenvironment causing disruption to iron metabolism, oxidative damage to cellular components, inflammatory responses and alterations to the motility of cells. The main research need is now to investigate whether the concentrations of aluminium measured in the human breast can lead in vivo to any of the effects observed in cells in vitro and this would be aided by the identification of biomarkers specific for aluminium action.

  12. Reactive sputter deposition of Al doped TiOx thin films using titanium targets with aluminium inserts

    International Nuclear Information System (INIS)

    Highlights: •Ti(Al)Ox thin films with varying Al fractions and increasing discharge current were deposited. •The reactive sputtering behaviour of Ti targets with Al inserts was studied. •XPS and EDX were used to check the stoichiometry of the films. •Optical transmittance measurements were performed to determine the band gap. -- Abstract: Al doped TiOx thin films were deposited using Ti targets with Al inserts. Both the effect of the number of aluminium inserts and the discharge current on the discharge voltage, on the aluminium content in the thin films, and on the reactive sputtering behaviour was investigated. The aluminium content in the film was measured using X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX). X-ray diffraction (XRD) revealed that the as-deposited thin films were amorphous, independent of the aluminium content or the discharge current. The XPS results indicated that the oxide films were substoichiometric. The optical band gap of the Ti(Al)Ox thin films was investigated as a function of the aluminium concentration and the discharge current. The addition of aluminium results in a significant increase of the band gap at low discharge currents, while no significant influence on the band gap was found at higher currents

  13. Effect of Aluminium and Silicon on High Temperature Oxidation Resistance of Fe-Cr-Ni Heat Resistant Steel

    Institute of Scientific and Technical Information of China (English)

    WANG Haitao; ZHAO Qi; YU Huashun; ZHANG Zhenya; CUI Hongwei; MIN Guanghui

    2009-01-01

    Fe-Cr-Ni heat resistant steels with different contents of Al and Si were cast in intermediate frequency induction furnace with non-oxidation method. With oxidation weight gain method, the oxidation resistance of test alloys was examined at 1 200℃ for 500 h. The effects of Al and Si on oxidation resistance were studied through analyses of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is shown that the composition of oxide scales is a decisive factor for the oxidation resistance of heat resistant steels. The compounded scale composed of Cr2O3, ar-Al2O3, SiO2 and Fe(Ni)Cr2O4, with flat and compact structure, fine and even grains, exhibits complete oxidation resistance at 1 200℃ Its oxidation weight gain rate is only 0.081 g/(m2·h). By the criterion of standard Gibbs formation free energy, a model of nucleation and growth of the compounded scale was established. The formation of the compounded scale was the result of the competition of being oxidated and reduction among Al, Si, and the matrix metal elements of Fe, Cr and Ni. The protection of the compounded scale was analyzed from the perspectives of electrical conductivity and strength properties.

  14. Design of the lines of aluminium drawing. Part 1; Conception des filieres de filage d'aluminium. Partie 1

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    After a general presentation, the second paragraph gives the main reasons of the complexity of the problem to be solved. Coming from the 'sciences of design', these aspects give valuable data to structure the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  15. Decreased toxicity of aluminium when the ionic strength increases in water; Blir aluminium mindre toksisk naar ionestyrken i vannet oeker?

    Energy Technology Data Exchange (ETDEWEB)

    Alstad, E.W. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper evaluates the acute mortality of fish caused by the toxicity of aluminium in water. The evaluation is based on the polymerization hypothesis. According to the author, the level of toxicity decreases when the concentration and charge of ions increase. The paper presents the preliminary results from the executed experiment. 2 refs., 2 figs., 1 tab.

  16. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    International Nuclear Information System (INIS)

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H2PO4− ions to HPO32− ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm−2 and 1.77 mW cm−2, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for bioelectronic applications. • Selective

  17. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Slaughter, Gymama, E-mail: gslaught@umbc.edu; Sunday, Joshua; Stevens, Brian

    2015-08-01

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H{sub 2}PO{sub 4}{sup −} ions to HPO{sub 3}{sup 2−} ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm{sup −2} and 1.77 mW cm{sup −2}, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for

  18. The influence of impurities on the formation of protective aluminium oxides on RuAl thin films

    Energy Technology Data Exchange (ETDEWEB)

    Guitar, M.A. [Functional Materials, Materials Science Departament, Saarland University, Saarbrücken D 66123 (Germany); Ramos-Moore, E. [Facultad de Física, Pontificia Universidad Católica de Chile, Santiago 7820436 (Chile); Mücklich, F., E-mail: muecke@matsci.uni-sb.de [Functional Materials, Materials Science Departament, Saarland University, Saarbrücken D 66123 (Germany)

    2014-05-01

    Highlights: • High-temperature oxidation RuAl intermetallic thin films were studied. • Microstructural analysis with and without impurities in the RuAl film. • Effect of impurities content in the oxidation kinetics was evaluated. • Stress evaluation of the oxide grown on RuAl with and without impurities. - Abstract: Single-phase RuAl is a promising candidate for protective coating materials in applications that demand oxidation resistance at temperatures above 600 °C in air. The main advantage of this system over other B2-aluminides emerges from the adherence to α-Al{sub 2}O{sub 3} oxide scale, formed at the surface under thermal cycling conditions. In particular, the presence of impurities and reactive elements may play a crucial role in tailoring the thermo-mechanical properties of the protective oxide. The influence of Cr and Fe impurities in the isothermal oxidation of RuAl thin films deposited on austenitic stainless steel was studied in air at 900 °C. The oxidation kinetics was analysed using an Arrhenius model, whereas microstructural and stress analyses were performed on α-Al{sub 2}O{sub 3} using scanning transmission electron microscopy and X-ray diffraction, respectively. The oxidation behaviour of RuAl was affected by the presence of impurities diffused from austenitic stainless steel substrate. Cracking in the α-Al{sub 2}O{sub 3} layer was observed in the absence of impurities as a result of thermal tensile stresses generated in the oxide scale. On the contrary, compressive stresses were developed after Fe (∼62 at.%) and Cr (∼20 at.%) diffusion into the RuAl film, which enhanced the activation energy of the oxide formation, mainly due to the energy barriers produced at grain boundaries. These findings highlight the potential tailoring of RuAl stability and performance at high temperatures through bottom-up diffusion of impurities and reactive elements from different substrates.

  19. Effects of Nano-Aluminium on The Combustion of A PolyNIMMO-Based Propellant

    Institute of Scientific and Technical Information of China (English)

    Clive Woodley; Peter Henning

    2014-01-01

    Propellants containing micro-aluminium particles have been shown to produce faster burn rates than conventional gun propellants.However,they are also more abrasive than conventional propellants.Nano-material propellants have been reported to give similar benefits to micron-material propellants but without the disadvantage of increased abrasion.Tests were conducted to compare the burn rates,ignitability and wear rates of a propellant loaded with 0% aluminium,15% micro-aluminium and 15%nano-aluminium.Closed vessel tests showed a burn rate increase of 39% in the range 30-250 MPa,and 70% at low pressure (50-100 MPa)for the nano-aluminium propellant compared with the baseline propellant.The micro-aluminium propellant showed only a 10% increase in the burn rate compared with the standard propellant.The ignition delay for the nano-aluminium propellant was slightly shorter than that of the baseline propellant.Substantially increased wear rates were measured for the micro-aluminium propellant.The nano-aluminium propellant showed reduced wear rates compared with the micro-aluminium propellant but these were still substantially greater than those for the baseline propellant.

  20. Numerical and experimental investigations of aluminium powder compaction; Numerische und experimentelle Untersuchungen zum Pulverpressen von Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Hanini, K.; Doege, E.; Schmidt-Juergensen, R. [Institut fuer Umformtechnik und Umformmaschinen, (IFUM) Universitaet Hannover, Welfengarten 1A, 30167 Hannover (Germany)

    2003-08-01

    The FEM simulation is a powerful means which can drastically reduce the time to production and costs in the optimization of powder forming processes. The current paper investigates experimentally and numerically die compaction of aluminium powder. The plastic deformation is formulated by using the Drucker-Prager-Cap-model. This yield criterion describes the compressibility of porous bodies and allows the prediction of crack formation in the green compact. Axial compaction tests have been performed to determine material parameters for hardening. Simulation examples are presented to demonstrate the ability of the model to compute the distribution of the relative density. Furthermore, the compaction of an axisymmetric workpiece was simulated in order to determine optimal tools kinematics and to avoid crack formation. (Abstract Copyright [2003], Wiley Periodicals, Inc.) [German] Die Auslegung und Optimierung pulvertechnologischer Umformverfahren basiert bisher zu einem grossen Teil auf Erfahrungswissen. Die numerische Simulation bietet hierbei eine kosten- und zeitsparende Alternative. Besonders hat sich die Finite-Elemente-Methode (FEM) als leistungsfaehiges Simulationsverfahren bewaehrt. Im Rahmen dieser Arbeit wird das Pulverpressen von Aluminiumpulver numerisch und experimentell untersucht. Hierbei wird das Drucker-Prager-Cap-Modell verwendet, um das kompressible Verhalten des Pulvers abzubilden und moegliche Rissbildungen waehrend des Pressvorgangs vorherzusagen. Durch Pressversuche werden die Materialkennwerte fuer dieses Modell hinsichtlich der Verdichtung und Verfestigung des Aluminiumpulvers ermittelt. Der Pressvorgang wird anhand ausgewaehlter Referenzbauteile simuliert. Von besonderem Interesse ist hierbei die Berechnung der Verteilung der relativen Dichte und die Vermeidung der Rissbildung durch Optimierung der Stempelkinematik. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  1. Aluminium content of foods originating from aluminium-containing food additives.

    Science.gov (United States)

    Ogimoto, Mami; Suzuki, Kumi; Haneishi, Nahoko; Kikuchi, Yuu; Takanashi, Mayu; Tomioka, Naoko; Uematsu, Yoko; Monma, Kimio

    2016-09-01

    Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples. PMID:27092423

  2. Steel sheet composite materials with foamed aluminium; Stahlblechverbundwerkstoffe mit geschaeumtem Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Baumeister, J.; Weber, M. [Institut fuer Angewandte Materialforschung, Bremen (Germany); Bleck, W.; Hagen, H. von [Technische Hochschule Aachen (Germany). Lehrstuhl und Inst. fuer Eisenhuettenkunde

    1999-07-01

    Sandwich structured steel sheets with a core of foamed aluminium can be produced by roll-bonding and glueing. Results of corrosion tests and laser welding tests so far were positive. Several applications have been proposed but none of them has been implemented as yet. The material is recommended for applications with a profile of requirements comprising structurally and functionally relevant characteristics. Recycling is unproblematic. [German] Zur Herstellung von Stahlblechsandwichverbunden mit einem Aluminiumschaumkern lassen sich die Verfahren Walzplattieren und Kleben einsetzen. Es sind Sandwichverbunde mit Gesamtdichten von 0,7 bis 2,0 g/cm{sup 3} und Gesamtdicken zwischen 10 und 32 mm darstellbar. Die Tafelgroessen fuer die vielversprechendsten Verfahren liegen derzeit bei ueber DIN A3 (konventionell geschaeumt) oder 160 mm x mehrere m (kontinuierlich im Banddurchlaufofen geschaeumt) und 2 m x 600 mm (geklebt). Es lassen sich gute mechanische Eigenschaften des Sandwichverbundes (Biegesteifigkeit) und hohe Versagensreserven bei Druck- und Biegebeanspruchungen sowie interessante funktionelle Eigenschaften (z.B. hohe Energieaufnahme) erzielen. Aus Tastversuchen zu Korrosionseigenschaften und Fuegeverfahren (Laserschweissen) konnten positive Resultate gewonnen werden. Vorschlaege zu Anwendungen bestehen, aber ein direkter Einsatz ist noch nicht realisiert worden. Ein Einsatz des Werkstoffverbundes ist sinnvoll in Gebieten, in denen ein Anforderungsprofil von strukturell und funktionell relevanten Eigenschaften vorherrscht. Das Recycling der rein metallischen Verbunde ist problemlos. (orig.)

  3. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    OpenAIRE

    Lunjie Zeng; Dung Trung Tran; Cheuk-Wai Tai; Gunnar Svensson; Eva Olsson

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure...

  4. Experimental Study of the Micro-Arc Oxide Coating Effect on Thermal Properties of an Aluminium Alloy Piston Head

    Directory of Open Access Journals (Sweden)

    N.Yu. Dudareva

    2015-09-01

    Full Text Available The purpose of the present study is to investigate the influence of differently sized microarc oxidation coatings, applied to the bottom of pistons made with an Al-12Si-Mg-Cu-Ni alloy, on its thermal properties by simulating the operation of a real engine. This study is based on the premise that the alumina coating thickness affects the heat transfer and temperature distribution in the piston. The analysis of thermal properties of pistons and suggestions for the optimal thermal barrier coating thickness are presented.

  5. Micro/nano-hybrid lens for enhancing light extraction using micro-milling and anodic aluminium oxide (AAO)

    International Nuclear Information System (INIS)

    In the recent past there has been much research towards increasing the transmission of light in optical systems by reducing the Fresnel reflection of radiation, as the reflection of light from surfaces seriously decreases the performance of an optical device. These drawbacks have been overcome by mainly two methods, which are anti-reflective coating and anti-reflective nanostructure formation. In this study, we developed a simple fabrication process for Al micro/nano hybrid lens (MNHL) moulds for efficient light extraction using micro-milling and anodic aluminum oxide (AAO). From these moulds, two different types of polymer MNHL were fabricated using hot-embossing; one was a polymer MNHL that was covered with nanostructures over the entire surface, and the other was one for which only the microlens surface was covered with nanostructures. Two different types of polymer MNHLs were evaluated and compared with each other concerning the light extraction performance. The MNHL with nanostructures only on the microlens surface exhibited a higher light extraction performance than the other by 20.7%. It is expected that the fabricated MNHL can be used for the amplification of small signals when observing the presence of bio-molecules dyed with a fluorescent material. (paper)

  6. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

  7. INVESTIGATION OF THE POTENTIAL PHYSIO-PATOLOGICAL EFFECTS OF ALUMINIUM IN PATIENTS WITH ALZHEIMER SPECIFIC SYMPTOMS

    Directory of Open Access Journals (Sweden)

    Constantin Bǎlǎeț

    2013-06-01

    Full Text Available In the past few years, there has been developed an idea about the connection between the Presence of aluminium in human blood and Alzheimer disease. The goal of our study was to demonstrate that there is a connection between the aluminium in the patients’ blood (who presented specific symptoms and Alzheimer disease’s occurrence, having a physiopathological determination. Aluminium dosage in a group of patients was analyzed (according to some pre-established procedures. 65% of the patients had 1-5% higher than normal values for aluminium level. Aluminium intoxication could lead to syndromes which could affect peoples’ activity. The general physicians must be aware of the need for detecting the aluminium in blood, of interpreting the physiopathological changes and of monitoring these changes in order to detect early symptoms of Alzheimer disease.

  8. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity. PMID:27025067

  9. The nature of point defects in plastically deformed aluminium

    International Nuclear Information System (INIS)

    In order to find out which types of point defect are produced by plastic deformation, 57Co-doped aluminium specimens were cold worked at various temperatures by unidirectional tensile deformation or cyclic torsion. The specimens were then annealed at increasing temperatures, and the trapping of defects at the 57Co probes was studied by Moessbauer spectroscopy. In none of the experiments were interstitials found, although it is known that in aluminium 57Co probes readily trap interstitials after low-temperature particle irradiation. However, vacancy trapping was found in two temperature ranges corresponding to two different migration energies of vacancies: in dislocations Esub(m)sup(d) approx.0.2 to 0.3 eV and in the lattice Esub(m) approx.= 0.6 eV. The consequences of the results on models of point defect production by cold working are discussed. (author)

  10. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines

    DEFF Research Database (Denmark)

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E;

    2016-01-01

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year....... Two patients had skin biopsies performed from their skin lesions, and 2 patients had the nodules surgically removed. Forty-two children had a patch-test performed with 2% aluminium chloride hexahydrate in petrolatum and 39 of them (92%) had a positive reaction. The persistent skin reactions were...... period 2003 to 2013 we identified 47 children with persistent skin reactions caused by childhood vaccinations. Most patients had a typical presentation of persisting pruritic subcutaneous nodules. Five children had a complex diagnostic process involving paediatricians, orthopaedics and plastic surgeons...

  11. Environment pollution with aluminium around a coalburning electric power plant

    International Nuclear Information System (INIS)

    The experiments were carried out from November 1991 till November 1993 on the area surrounding an electric power plant within the circle of 20 km diameter and five geographical directions (N, S, SE, E, W). The results presented in this paper have indicated the threats caused by emissions of the power plant ashes and dusts. Mean aluminium content in soil has been multiply surpassed on the area studied. This must have as impact on fauna and flora. The distribution and intensity of pollution is determined first of all by the distance from the emitters and direction of prevailing winds. A part of aluminium contained in water soluble compounds can be distributed on large areas, what adds a lot to the threat to animals. That is why high chimneys do not solve the problem of pollution around big industrial plants. (author)

  12. Nano α-alumina powders from aluminium dross waste

    International Nuclear Information System (INIS)

    The paper describes a solvo thermal chemical process to recycle aluminium dross waste into nano α-alumina powder. The process includes washing to remove the unwanted sodium follow by dissolving of this waste with dilute acid. The solvo thermal process then proceed with addition of propanol to crystallize the aluminium hydroxide. XRD analysis of this crystal shows that it belongs to Gibbs site (Al(OH)3). The crystals were then calcined at 1300 degree C where white powder was produced. Characteristic studies were then performed on this powder using XRD, SEM, EDX and particle size analysis showing that it has single α-alumina crystal phase with almost spherical shape. As the initial particle size is coarse and had a mean particle size of 3.80 μm, high speed wet milling was used and enable to reduce it to 0.49 μm. (Author)

  13. High-pressure direct synthesis of aluminium nitride

    CERN Document Server

    Bockowski, M; Grzegory, I; Krukowski, S; Wróblewski, M; Porowski, S

    2002-01-01

    We report the results of direct synthesis of aluminium nitride (AlN) under high nitrogen pressure up to 1 GPa and temperatures up to 2000 K. At pressure from 10 to 650 MPa we observe the combustion synthesis of AlN. As the result of the combustion process one can obtain the AlN sintered powder or AlN/Al metal matrix composites. For N sub 2 pressure higher than 650 MPa the crystal growth of AlN from the solution of atomic nitrogen in aluminium is possible. Both needle-like and bulk AlN single crystals, up to 1 cm and 1 mm, respectively, have been obtained.

  14. Thermal Effect of Ceramic Nanofiller Aluminium Nitride on Polyethylene Properties

    Directory of Open Access Journals (Sweden)

    Omer Bin Sohail

    2012-01-01

    Full Text Available Ethylene polymerization was done to form polyethylene nano-composite with nanoaluminum nitride using zirconocene catalysts. Results show that the catalytic activity is maximum at a filler loading of 15 mg nanoaluminum nitride. Differential scanning calorimeter (DSC and X-ray diffraction (XRD results show that percentage crystallinity was also marginally higher at this amount of filler. Thermal behavior of polyethylene nanocomposites (0, 15, 30, and 45 mg was studied by DSC and thermal gravimetric analyzer (TGA. Morphology of the component with 15 mg aluminium nitride is more fibrous as compared to 0 mg aluminium nitride and higher filler loading as shown by SEM images. In order to understand combustibility behavior, tests were performed on microcalorimeter. Its results showed decrease in combustibility in polyethylene nanocomposites as the filler loading increases.

  15. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    K T Kashyap; T Chandrashekar

    2001-08-01

    Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the scientific literature. The nucleant effects i.e. which particle and its characteristics nucleate -Al, has been the subject of intensive research. Lately the solute effect i.e. the effect of dissolved titanium on grain refinement, has come into forefront of grain refinement research. The present paper attempts to review the literature on the nucleant effects and solute effects on grain refinement and addresses the importance of dissolved titanium in promoting nucleation of -Al on nucleant particles.

  16. Impact of Inert Metal Particles Flow on Aluminium Plate

    Institute of Scientific and Technical Information of China (English)

    WANG Zhongqi; LIU Yi; CHEN Yahong; BAI Chunhua

    2008-01-01

    Inert metal explosive, a new kind of explosive, is a mixture of high explosive and inert metal particle.When this kind of explosive is detonated, an inert metal particle flow will be formed by the explosive product driving.To determine the characteristics of the movement of the metal particle flow, a series of aluminium plates were designed to be the targets on which the metal particle flow impacted.The test result was presented and a numerical model was set up to analyze the impact of the high speed inert metal particles on aluminium plate.Based on the numerical analysis, the relationship between the characteristic of the mark on the target plate and the initial condition of the inert metal particles was proposed.From the analysis of the impact on target plates, more information about the movement of the metal particles could be reconstructed.

  17. Muon motion in pure and weakly doped aluminium

    CERN Document Server

    Niinikoski, T O; Karlsson, E; Kehr, K W; Norlin, L O; Richter, D; Welter, J M

    1981-01-01

    The authors have studied the diffusion and localization of positive muons in pure and weakly doped aluminium, in the temperature range 30 mK-100K, by measuring the damping parameter of the muon spin rotation ( mu SR) signal. In this paper they discuss some of their recent results and draw the following conclusions: i) in pure Al, positive muons are delocalized in band states (coherent motion); ii) in Al doped with 5-70 ppm Mn, the temperature, concentration and field dependences of the damping parameter suggest diffusion or capture limited trapping to octahedral interstitial sites in the aluminium lattice below 1K; iii) above 2K a two-state diffusion-trapping model explains well the peak in the damping parameter, which appears at 15-50K for the dopants Mn, Mg, Li and Ag so far studied. (11 refs).

  18. Buffering effects on electrograining of aluminium in nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Koroleva, E.V. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom)]. E-mail: e.koroleva@umist.ac.uk; Thompson, G.E. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Skeldon, P. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Hollrigl, G. [Alcan Technology and Management Ltd., Bad. Bahnhofstrasse 16, CH-8212 Neuhausen (Switzerland); Lockwood, S. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom); Smith, G. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom)

    2005-09-01

    Electrograining of a binary Al-Si alloy has been undertaken in nitric acid based electrolytes, with the resultant surfaces examined by scanning and transmission electron microscopies. Depending on electrograining conditions, the pit appearance varies from hemispherical to large lateral pits, with the latter favoured in relatively acidic electrolytes. The conditions prevailing in the pit have been explored through use of aluminium ion additions to the nitric acid electrolyte as well as additions of species which influence the precipitation and dissolution of aluminium hydroxide. These confirm that control of the pit solution pH, through hydroxide generation, as a result of the selected electrograining conditions and consequent anodic and cathodic polarisation, enables tailoring of the resultant electrograined surface appearance.

  19. Evolution of Structural Damage in Aluminium Irradiated with Xenon Ions

    CERN Document Server

    Hofmann, A

    2001-01-01

    Structural defect evolution in high-purity aluminium both as-irradiated and annealed after irradiation has been investigated by transmission electron microscopy. The foils of high-purity aluminium were irradiated with 124 MeV Xe ions with fluence up to 2\\cdot 10^{16} Xe^+ cm^{-2} at room temperature and at 100 ^{o}C. The samples irradiated at 100 ^{o}C were annealed at 480 and 600 ^{o}C. At initial stage of irradiation, at low fluence (\\leq 2\\cdot 10^{14} Xe^+ cm^{-2}) the isolated dislocation loops are observed. When ion fluence increased the loops grow. At fluences above 10^{15} Xe^+ cm^{-2} cm the microstructure is characterized by high-density small voids (pores) which are grown and slowly merged with fluence increasing. For these conditions, the most possible mechanism of pore growth is their diffusion-controlled coalescence.

  20. Sputter deposition of aluminium on colloidal polymer templates

    Energy Technology Data Exchange (ETDEWEB)

    Gehrke, Rainer; Buffet, Adeline; Couet, Sebastien; Schlage, Kai; Roth, Stephan V.; Roehlsberger, Ralf [HASYLAB, DESY, Hamburg (Germany); Herzog, Gerd [HASYLAB, DESY, Hamburg (Germany); Inst. f. Exp. Phys., Univ. Hamburg (Germany); Kaune, Gunar; Koerstgens, Volker; Meier, Robert; Metwalli, Ezzeldin; Mueller-Buschbaum, Peter [TU Muenchen, Physik-Department, Garching (Germany); Wurth, Wilfried [Inst. f. Exp. Phys., Univ. Hamburg (Germany)

    2009-07-01

    This work addresses an approach to the formation of metal nanowire meshes on surfaces. Colloidal dispersions of 100 nm polystyrene spheres were spincoated on silicon. Islands of packed layers of spheres were formed which served as template for sputter deposition of aluminium. Structure formation was investigated with grazing incidence small angle X-ray scattering at beamline BW4 at HASYLAB/DESY using an in-situ sputtering chamber, thus scattering could be observed during metal deposition. The measurements indicate, that at the beginning of the deposition the metal atoms assemble in the indentations between the spheres, only after longer sputtering times the surface becomes completely covered with aluminium. If an unsputtered sample was heated beyond the glass transition temperature the lateral ordering vanished, if sputtering was stopped before complete metal coverage ordering remained upon heating. This indicates that the metal forms a stable structure separating the polymer spheres from each other.

  1. Experimental evidence for a dynamical crossover in liquid aluminium.

    Science.gov (United States)

    Demmel, F; Fraile, A; Szubrin, D; Pilgrim, W-C; Morkel, C

    2015-11-18

    The temperature dependence of the dynamic structure factor at next-neighbour distances has been investigated for liquid aluminium. This correlation function is a sensitive parameter for changes in the local environment and its Fourier transform was measured in a coherent inelastic neutron scattering experiment. The zero frequency amplitude decreases in a nonlinear way and indicates a change in dynamics around 1.4 ∙ Tmelting. From that amplitude a generalized viscosity can be derived which is a measure of local stress correlations on next-neighbour distances. The derived generalized longitudinal viscosity shows a changing slope at the same temperature range. At this temperature the freezing out of degrees of freedom for structural relaxation upon cooling sets in which can be understood as a precursor towards the solid state. That crossover in dynamics of liquid aluminium shows the same signatures as previously observed in liquid rubidium and lead, indicating an universal character. PMID:26465204

  2. Uranium and thorium behavior at aluminium floating-zone refining

    International Nuclear Information System (INIS)

    Uranium and thorium behaviour during aluminium refining by crystallization from the melt is ascertained. Measurements of of uranium and thorium radioactive impurities content in high-purity aluminiumn samples using the surface α-activity method are carried out. The content of the given impurities happened to be less than 1 x 10-7 mass.%. Such purity satisfies the requirements to materials applied in the low background 71Ge detection system of gallium-germanium solar neutrino detector

  3. Work Hardening and Mechanical Anisotropy of Aluminium Sheets and Profiles

    OpenAIRE

    Ryen, Øyvind

    2003-01-01

    The processing of aluminium alloys from casting to end product is associated with a large number of metallurgical phenomena. In order to further improve and optimise process routes and alloys, a thorough understanding of the thermomechanical treatments by experimental observations and physically based modelling is necessary.In part A of this thesis the work hardening behaviour of non-heat treatable alloys is followed up to large strains. The evolution in strength, microstructure and texture d...

  4. Fatigue Strength of Friction Stir Welded Joints in Aluminium

    OpenAIRE

    Ericsson, Mats

    2005-01-01

    Solid state Friction stir welding (FSW) is of major interest in the welding of aluminium since it improves the joint properties. Many applications where Al-alloys are used are subject to varying load conditions, making fatigue failure a critical issue. In the scope of this thesis, the fatigue performance of friction stir welded AlMgSi-alloy 6082 has been investigated. Static and dynamic properties of different joint configurations and welds produced with varying process parameters have been d...

  5. Aluminium extrusion investigated by theory, experiment and FEM-analysis

    OpenAIRE

    Khorasani, Sepinood Torabzadeh

    2015-01-01

    The process of aluminium extrusion has important influence in metal forming industry because of its ability to produce profiles with different shapes, sizes and complicated geometries. The required extrusion load is depending on the process parameters such as the flow stress of the billet material, velocity field, strain rate distribution, and thermal conditions within extrusion. These conditions are so important for industries, and interesting for academia, that research has been...

  6. Melting Transition of Small Aluminium Clusters Al11-20

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; ZHANG Feng-Shou; ZHU Zhi-Yuan

    2007-01-01

    Heat capacities of small aluminium clusters Al11-20 are investigated using MD simulation with empirical manybody Gupta potential. The heat capacities of some clusters Al11, Al12, Al13 and Al19 show well-defined peaks while the heat capacities of Al15-18 indicate a gradual melting transition. The spectra of isomers obtained by quenches along the MD trajectory give good interpretation for those results.

  7. Establishment of integrated information displays in aluminium surfaces using nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan; Hansen, Hans Nørgaard; Bladt, Henrik H.;

    2006-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in aluminium that can be penetrated by light. This work has resulted in a patent describing how to obtain this effect by material removal in local areas in a solid material. The idea behind an invisible display ...... micromachining with ultra-short pulses, selective etching combined with anodizing, and electrochemical machining....

  8. Texture development during recrystallization of aluminium containing large particles

    DEFF Research Database (Denmark)

    Juul Jensen, Dorte; Hansen, Niels; Humphreys, F. J.

    1985-01-01

    The recrystallization process in heavily deformed commercially pure aluminium containing large intermetallic particles was studied by in situ neutron diffraction texture measurements and various microscopical techniques including texture measurements in local areas and simultaneous determination of...... size and orientation of individual grains. The formation and growth of recrystallization nuclei at the particles and in the matrix were examined by correlating the measured change in texture to the observed change in microstructure. It was found that prolific nucleation of grains having a wide spread...

  9. Load carrying capacity analysis of materials for aluminium rims

    OpenAIRE

    Fajdiga, Matija; Čižman, Jure

    2015-01-01

    In this contribution we present an experimental simulation of the fatique strength of clamped aluminium rims. This is supported by numerical modelling using the Finite Element Method (FEM), which was used for stress-strain analysis of a model representing a clamped detail during bendings. The design and analysis of the model are made simultaneously on an integrated computer controlled test rig for testing the fatique strength of clamped parts subjected to bending. The simulation is evaluated ...

  10. Fabrication and characterisation of uranium, molybdenum, chromium, niobium and aluminium

    International Nuclear Information System (INIS)

    This paper describes fabrication of binary uranium alloys by melting and casting. The following alloys with nominal composition were obtained by melting in the vacuum furnace: uranium with niobium contents from 0.5%- 4.0% and uranium with molybdenum contents from 0.4% - 1.2%. Uranium alloys with chromium content from 0.4% - 1.2% and uranium alloy with 0.12% of aluminium were obtained by vacuum induction furnace (electric arc melting)

  11. State diagram of copper-aluminium alloys after neutron irradiation

    International Nuclear Information System (INIS)

    It is ascertained that under reactor irradiation of copper-aluminium alloys (18.0-31.2 at% of Al) radiation-induced phase transformations occur, alpha-phase is decomposed into two ones with alpha'-phase precipitation, in gamma2-phase separate regions of its high-temperature disordered modification (gamma1-phase) are formed. Thermal stability of precipitations is investigated, regions of their existence are defined on the state diagram

  12. Study of twist boundaries in aluminium. Structure and intergranular diffusion

    International Nuclear Information System (INIS)

    This research thesis addresses the study of grain boundaries in oriented crystals, and more particularly the systematic calculation of intergranular structures and energies of twist boundaries of <001> axis in aluminium, the determination of intergranular diffusion coefficients of zinc in a set of twist bi-crystals of same axis encompassing a whole range of disorientations, and the search for a correlation between these experimental results and calculated structures

  13. Hole quality and burr reduction in drilling aluminium sheets

    DEFF Research Database (Denmark)

    Pilny, Lukas; De Chiffre, Leonardo; Piska, Miroslav;

    2011-01-01

    Optimization of the metal drilling process requires creation of minimum amount of burrs and uniform appearance of the drilled holes. In this paper, an experimental investigation was performed on 2 mm sheets of wrought aluminium alloy Al99.7Mg0.5Cu-H24, using 1.6 and 2 mm diameter drills. Cutting ...... drilled holes was fulfilled as well as high productivity achieved. Such optimized process results in a noticeable production cost reduction....

  14. METAL MATRIX COMPOSITES BASED ON ALUMINIUM LITHIUM AND SILICON CARBIDE

    OpenAIRE

    White, J.; Hughes, I; Willis, T.; Jordan, R.

    1987-01-01

    The present study tests the feasibility of producing metal matrix composites based on aluminium-lithium alloys. The first step in this process has been to produce an MMC based on 8090 with SiC. This has been successfully produced by Alcan International using the "Osprey" spray deposition process. The raw billets have been processed initially by extrusion. The tensile properties of this material have been determined and the strength compares favourably with DC cast alloys. Modulus is improved ...

  15. Noncontact ultrasonic thickness measurements of thin aluminium sheet

    International Nuclear Information System (INIS)

    A method has been described for the noncontact ultrasonic thickness measurements of thin aluminium sheets, using a Q-switched ruby laser generation concentric with an annular electro-magnetic acoustic transducer (EMAT) detection to imitate pulse-echo system. The detected waveforms were analyzed with the cut-off frequences of the higher order lamb modes. The results show in a good egreement with micrometer measurements within 2% discrepancy. (authors). 22 refs, 6 figs

  16. Oblique Impact of Projectile on Thin Aluminium Plates

    Directory of Open Access Journals (Sweden)

    W.U. Khan

    2003-04-01

    Full Text Available Experiments were performed, wherein cylindrical projectiles made of hardened steel were impacted on commercially available aluminium plates at different angles. Projectiles were of 12.8 mm diameter and plates were of 0.81 mm, 1.52mm and 1.91mm thicknesses. Based on the experimental results, an analytical model has been developed to predict the residual velocity of the projectile and the ballistic limit of the plate.

  17. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    OpenAIRE

    Ma D; Guo M; Zhang M

    2013-01-01

    Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC), a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate...

  18. Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

    OpenAIRE

    Sinou, Jean-Jacques; Macquaire, Bruno

    2003-01-01

    International audience For a car manufacturer, reducing the weight of vehicles is an obvious aim. Replacing steel by aluminium moves towards that goal. Unfortunately, aluminium's stamping numerical simulation results are not yet as reliable as those of steel. Punch-strength and spring-back phenomena are not correctly described. This study on aluminium validates the behaviour law Hill 48 quadratic yield criterion with both isotropic and kinematic hardening. It is based on the yield surface ...

  19. Subgrain Growth, Recovery Kinetics and Nucleation of Recrystallization of Cold Deformed Aluminium Alloys

    OpenAIRE

    Bunkholt, Sindre

    2013-01-01

    Phenomena related to annealing of aluminium alloys are among the least understood in aluminium metallurgy but very important for industrial thermo-mechanical processing i.e. deformation and annealing. Physical models are used to predict recovery and recrystallization behaviour, and associated material properties, industrially. However, alloy development, e.g. to incorporate more recycled aluminium, has shown that current softening models are not satisfactory. Thus, improvements do require a b...

  20. Selected properties of the aluminium alloy base composites reinforced with intermetallic particles

    OpenAIRE

    M. Adamiak

    2005-01-01

    Purpose: The main aim of this work is to investigate two types of intermetallics TiAl and Ti3Al as reinforcement and their influence on selected properties and microstructure of aluminium matrix composites.Design/methodology/approach: Aluminium matrix composites were produced employing the atomised aluminium alloy AA6061 as metal matrix, when as reinforcement TiAl and Ti3Al intermetallics particles were used. The powders were cold pressed and then hot extruded. To evaluate the effect of mecha...

  1. Electrodeposition of aluminium film on P90 Li-Al alloy as protective coating against corrosion

    OpenAIRE

    U. Bardi; Caporali, S; M. Craig; A. Giorgetti; Perissi, I; Nicholls, J. R.

    2009-01-01

    In this paper we report on the electrodeposition of thin aluminium layers on P90 lithium–aluminium alloy at room temperature from a chloroaluminate ionic liquid (1-butyl-3-methyl imidazolium heptachloroaluminate [BMIm]Al2Cl7). We found that the treatment of the P90 sample's surface is a key point to obtain good quality coatings. On freshly mechanically polished surfaces, thin (about 24 µm), homogeneous and dense aluminium layers were obtained at 10 µm h− 1 deposition rate. F...

  2. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    OpenAIRE

    Mold, M; Shardlow, E; Exley, C.

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, pote...

  3. Lewis acid fragmentation of a lithium aryloxide cage: generation of new heterometallic aluminium-lithium species.

    Science.gov (United States)

    Muñoz, Ma Teresa; Urbaneja, Carmen; Temprado, Manuel; Mosquera, Marta E G; Cuenca, Tomás

    2011-11-14

    Heterometallic aluminium-lithium species were prepared by the fragmentation reaction of the hexametallic cage compound [Li{2,6-(MeO)(2)C(6)H(3)O}](6) (1) with alkyl aluminium derivatives. Depending on the aluminium precursor, the species formed present different nuclearities in the solid state as shown by single crystal X-ray analysis. Spectroscopic and computational studies have been performed to study the nuclearity of the synthesized compounds in solution.

  4. The Effect of Thickness of Aluminium Films on Optical Reflectance

    Directory of Open Access Journals (Sweden)

    Robert Lugolole

    2015-01-01

    Full Text Available In Uganda and Africa at large, up to 90% of the total energy used for food preparation and water pasteurization is from fossil fuels particularly firewood and kerosene which pollute the environment, yet there is abundant solar energy throughout the year, which could also be used. Uganda is abundantly rich in clay minerals such as ball clay, kaolin, feldspar, and quartz from which ceramic substrates were developed. Aluminium films of different thicknesses were deposited on different substrates in the diffusion pump microprocessor vacuum coater (Edwards AUTO 306. The optical reflectance of the aluminium films was obtained using a spectrophotometer (SolidSpec-3700/DUV-UV-VIS-NIR at various wave lengths. The analysis of the results of the study revealed that the optical reflectance of the aluminium films was above 50% and increased with increasing film thickness and wavelength. Thus, this method can be used to produce reflector systems in the technology of solar cooking and other appliances which use solar energy.

  5. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    DEFF Research Database (Denmark)

    Aggerbeck, Martin

    The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions of this ......The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions...... described magnetron sputtered Al-Ti coatings showed that 13 wt. % titanium and more improved the corrosion resistance at pH 13.5 and this was further improved by heat treatment, especially at 400 °C and more. The improved corrosion properties were ascribed to structural relaxation, decreased galvanic...... potential differences in the microstructure, and protection from the network of the Al3Ti phases precipitated during the heat treatment. Laser surface cladding of aluminium containing up to 20 wt. % Ti6Al4V were studied focusing on the microstructure and the alkaline corrosion properties. Due...

  6. Control of Microthrix parvicella by aluminium salts addition.

    Science.gov (United States)

    Durban, N; Juzan, L; Krier, J; Gillot, S

    2016-01-01

    Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella.

  7. Analysis of Orthogonal Cutting of Aluminium-based Composites

    Directory of Open Access Journals (Sweden)

    P. Ravinder Reddy

    2002-10-01

    Full Text Available A turning test on aluminium-based metal-matrix composites (MMCs (aluminium-30% silicon carbide was performed with K-20 carbide tool material and wear patterns and the wear land growth rates were analysed to evaluate the wear characteristics and to classify the relationship between the physical (mechanical properties and the flank wear of cutting tools. The study was also extended to the machining aspects and the width of cuts on MMCs and the influence of various cutting parameters. The experiments were conducted to measure the temperature along the cutting tool edge using thermocouple at various cutting speeds, and depth of cuts, keeping the feed rate constant while turning with K-20 carbide cutting tool. The finite-element method was used to simulate the orthogonal cutting of aluminium-based MMCs. The heat generation at the chip-tool interface, frictional heat generation at the tool flank, and the heat generation at the work tool interface were calculated analytically and imposed as boundary conditions. The analysis of the steady-state heat transfer was carried out and the temperature distribution at cutting edge, shear zone, and interface regions have been reported.

  8. Highly stable CuInS2@ZnS:Al core@shell quantum dots: the role of aluminium self-passivation.

    Science.gov (United States)

    Rao, Pinhua; Yao, Wei; Li, Zhichun; Kong, Long; Zhang, Wenqi; Li, Liang

    2015-05-25

    A simple approach was introduced to enhance the photostability of CuInS2@ZnS core@shell quantum dots (QDs) by doping aluminium into the ZnS shell. Aluminium in the as-prepared QDs was oxidized to Al2O3, which formed a passivation oxide layer that effectively prevents photo-degradation of QDs during long-term light irradiation.

  9. Aluminium localization in root tips of the aluminium-accumulating plant species buckwheat (Fagopyrum esculentum Moench).

    Science.gov (United States)

    Klug, Benjamin; Specht, André; Horst, Walter J

    2011-11-01

    Aluminium (Al) uptake and transport in the root tip of buckwheat is not yet completely understood. For localization of Al in root tips, fluorescent dyes and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) were compared. The staining of Al with morin is an appropriate means to study qualitatively the radial distribution along the root tip axis of Al which is complexed by oxalate and citrate in buckwheat roots. The results compare well with the distribution of total Al determined by LA-ICP-MS which could be reliably calibrated to compare with Al contents by conventional total Al determination using graphite furnace atomic absorption spectrometry. The Al localization in root cross-sections along the root tip showed that in buckwheat Al is highly mobile in the radial direction. The root apex predominantly accumulated Al in the cortex. The subapical root section showed a homogenous Al distribution across the whole section. In the following root section Al was located particularly in the pericycle and the xylem parenchyma cells. With further increasing distance from the root apex Al could be detected only in individual xylem vessels. The results support the view that the 10 mm apical root tip is the main site of Al uptake into the symplast of the cortex, while the subapical 10-20 mm zone is the main site of xylem loading through the pericycle and xylem parenchyma cells. Progress in the better molecular understanding of Al transport in buckwheat will depend on the consideration of the tissue specificity of Al transport and complexation.

  10. Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

    Science.gov (United States)

    Yang, Mei; Jiang, Lixin; Huang, Huiping; Zeng, Shengbo; Qiu, Fen; Yu, Miao; Li, Xiaorong; Wei, Sheng

    2014-01-01

    Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg), fried twisted cruller (median, 466.0 mg/kg), shell (median, 107.1 mg/kg). The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake). But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week) than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

  11. Determination of aluminium contents in selected food samples by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Food and food products are the main sources of Aluminium entering the human body. In order to know aluminium contents in food and food products, selected 26 samples from local market were analyzed by instrumental neutron activation analysis (INAA) using reactor neutrons and high resolution gamma-ray spectrometry. INAA using 1,779 keV γ-ray of 28Al (2.24 min) was used for aluminium concentrations in the range of 33-529 mg kg-1. Two NIST standard reference materials (SRMs) and two IAEA reference materials (RMs) were analyzed by INAA for quantification of aluminium as a part of method validation. (author)

  12. Aluminium nitride: from the powder to the substrate. Le nitrure d'aluminium: de la poudre au substrat

    Energy Technology Data Exchange (ETDEWEB)

    Jarrige, J. (Lab. de Ceramiques Nouvelles, Limoges (France)); Mexmain, J. (Lab. de Ceramiques Nouvelles, Limoges (France)); Oumaloul, M. (Lab. de Ceramiques Nouvelles, Limoges (France)); Bachelard, R. (CRRA ELF ATOCHEM, Pierre Benite (France)); Disson, J.P. (CRRA ELF ATOCHEM, Pierre Benite (France))

    1993-04-01

    The aluminium nitride is a material which should replace alumina or beryllia as substrate for power electronic applications. The powder, prepared by carbothermal nitridation, is dispersed in a butanone-2-ethanol azeotrop solvent with a phosphate ester. Electrical conductivity, sedimentation, viscosity have been used to determine which phenomena take place in the defloculation of the suspension. The stability of AlN suspensions is due mainly to an electrostatic mechanism, with a steric contribution. The aluminium nitride tape-casting slip has been sintered at 1850 C in a nitrogen atmosphere. Removing of the binder and plasticizer can be performed in the same oven at 650 C, due to their nature and low concentration. The thermal conductivity of the substrates has been measured and is in the 160 to 200 W/m.K range. (orig.).

  13. Refractory oxides containing aluminium and barium Oxidos refratários contendo alumínio e bário

    Directory of Open Access Journals (Sweden)

    T. J. Davies

    1998-10-01

    Full Text Available Oxides containing aluminium and barium, optionally with chromium, are refractory with several possible industrial uses. A gel precursor of an oxide having the formula BaO.n(Al2xCr2yO3, where 1Oxidos contendo alumínio e bário, opcionalmente com crômio, são refratários com vários possíveis usos industriais. Foi preparado um gel precursor de um óxido de formula BaO.n(Al2xCr2yO3, com 1

  14. A low cost, light weight cenosphere–aluminium composite for brake disc application

    Indian Academy of Sciences (India)

    V Saravanan; P R Thyla; S R Balakrishnan

    2016-02-01

    The commonly used composite material for brake rotor consists of silicon carbide (SiC) or aluminium oxide (Al$_2$O$_3$) particles which are more expensive. The weight of conventionally used composite is more compared to base alloy. The aim of this paper is to develop a light weight material for brake disc applications thereby substituting base alloy and conventional composite. This analysis led to 10 vol% cenosphere reinforced aluminium alloy (AA) 6063 composite as the most appropriate material for brake disc. To ensure the manufacturability of composite, composite brake rotor was casted using the sand casting technique and was machined to achieve the final component. Thermal capability of brake disc was ensured by studying temperature variation through vehicle testing procedure of disc brake. Cost reduction is one of the important benefit acquired using cenosphere reinforced composite. This was ensured by cost estimation and analysis. The cost estimated to manufacture the AA6063 brake disc was compared with composite cost.

  15. Aluminium EN AW-2124 alloy matrix composites reinforced with Ti(C,N), BN and Al2O3 particles

    International Nuclear Information System (INIS)

    Investigation results of the aluminium alloy EN AW-2124 matrix composite materials with particles of the powders Ti(C,N), BN and Al2O3 (15 wt.%) are presented in the paper. In order to obtain uniform distribution of reinforcement particles in aluminium alloy matrix powders of composite components have been milled in the rotary ball-bearing pulverizer. The composites have been pressed in laboratory vertical press at room temperature under the pressure of 500 kN. Obtained die samplings have been heated to the temperature 520-550 oC and extruded. Bars of diameter 8 mm have been received as a final product. Metallographic examination of the composites materials' structure shows non-uniform distribution of reinforced powders in the aluminium alloy matrix banding of reinforcements particles corresponds to the extrusion direction. Particles of reinforcement distribution in aluminium alloy matrix is irregular, some agglomerations of powder of aluminium oxide and porosity of different size have been noticed. Investigations of hardness and ultimate compressive strength show that the particles of reinforcement improve mechanical properties of composite materials. Investigations of compressive strength, carried out at room temperature, enable to compare mechanical properties of matrix and composite. (author)

  16. Synthesis of aluminium nanoparticles by arc plasma spray under atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Mandilas, Charalampos; Daskalos, Emmanouil [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Karagiannakis, George, E-mail: gkarag@cperi.certh.gr [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Konstandopoulos, Athanasios G., E-mail: agk@cperi.certh.gr [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Department of Chemical Engineering, Aristotle University, P.O. Box 1517, 54006 Thessaloniki (Greece)

    2013-01-01

    Highlights: Black-Right-Pointing-Pointer A customized arc-plasma spraying based system has been designed and implemented. Black-Right-Pointing-Pointer The system is relatively simple, robust and operates at atmospheric pressure. Black-Right-Pointing-Pointer Preparation of aluminium nanoparticles from micron-sized powder was successful. Black-Right-Pointing-Pointer Various nano-sized distributions were possible depending on operating parameters. Black-Right-Pointing-Pointer Optimization of the proposed design will lead to higher efficiencies and throughput. - Abstract: The present study addresses the feasibility to synthesize aluminium nanoparticles (NPs) from micron-sized aluminium powder with the use of a customized atmospheric plasma spraying (APS) technique. Using APS, nanoparticle synthesis can be achieved via rapid melting and vaporization of the initial micrometric particles and their subsequent re-nucleation. A custom mantle system was designed and developed with the aid of relevant simplified CFD simulations. The mantle provided the necessary inert environment (argon), at ambient pressure, in order to avoid any oxidation of the metal during plasma spraying while promoted rapid quenching of the gasified metal. The particles formed were collected with the aid of a quartz filter downstream of the plasma flame and the production rate achieved was 2 g min{sup -1}. Ex situ post-characterization of the particles via X-ray diffraction, specific surface area measurement (BET), transmission electron microscopy (TEM) coupled with energy dispersive spectrometry (EDS) and thermogravimetric analysis (TGA) under air revealed that the powders obtained primarily comprised of monocrystalline metallic aluminium nanoparticles of almost spherical shape. The NPs possessed a 2-5 nm oxide coating layer. By regulating the conditions inside the mantle, a variety of different size distributions were obtained.

  17. Efficacy of chelation therapy to remove aluminium intoxication.

    Science.gov (United States)

    Fulgenzi, Alessandro; De Giuseppe, Rachele; Bamonti, Fabrizia; Vietti, Daniele; Ferrero, Maria Elena

    2015-11-01

    There is a distinct correlation between aluminium (Al) intoxication and neurodegenerative diseases (ND). We demonstrated how patients affected by ND showing Al intoxication benefit from short-term treatment with calcium disodium ethylene diamine tetraacetic acid (EDTA) (chelation therapy). Such therapy further improved through daily treatment with the antioxidant Cellfood. In the present study we examined the efficacy of long-term treatment, using both EDTA and Cellfood. Slow intravenous treatment with the chelating agent EDTA (2 g/10 mL diluted in 500 mL physiological saline administered in 2 h) (chelation test) removed Al, which was detected (using inductively coupled plasma mass spectrometry) in urine samples collected from patients over 12 h. Patients that revealed Al intoxication (expressed in μg per g creatinine) underwent EDTA chelation therapy once a week for ten weeks, then once every two weeks for a further six or twelve months. At the end of treatment (a total of 22 or 34 chelation therapies, respectively), associated with daily assumption of Cellfood, Al levels in the urine samples were analysed. In addition, the following blood parameters were determined: homocysteine, vitamin B12, and folate, as well as the oxidative status e.g. reactive oxygen species (ROS), total antioxidant capacity (TAC), oxidized LDL (oxLDL), and glutathione. Our results showed that Al intoxication reduced significantly following EDTA and Cellfood treatment, and clinical symptoms improved. After treatment, ROS, oxLDL, and homocysteine decreased significantly, whereas vitamin B12, folate and TAC improved significantly. In conclusion, our data show the efficacy of chelation therapy associated with Cellfood in subjects affected by Al intoxication who have developed ND.

  18. Surface formation in direct chill (DC) casting of 6082 aluminium alloys

    Science.gov (United States)

    Bayat, N.; Carlberg, T.

    2016-03-01

    Surface defects in aluminium billet production are a real problem for the subsequent extrusion procedure. Extrusion productivity can be influenced by the surface properties, which is defined as surface appearance, surface segregation zone depth and large Mg2Si and β-particles (Al5FeSi). In this research the surface formation during DC casting of 6082 aluminium billets produced by the air slip technology is studied. The surface microstructures of 6082 aluminium alloys with smooth and wavy surface appearances were investigated, including segregation zone depths and phase formation. The results were discussed based on the exudation of liquid metal through the mushy zone. The specific appearance of the wavy surface of 6082 alloys was correlated to how the oxide skin adheres to the underlying mushy zone and coupled to the dendritic coherency and surface tension of the skin. The occurrence of different phases at the very surface and in the layer just below was explained by variations in solidification directions and subsequent segregation patterns.

  19. ECAP – New consolidation method for production of aluminium matrix composites with ceramic reinforcement

    Directory of Open Access Journals (Sweden)

    Mateja Šnajdar Musa

    2013-06-01

    Full Text Available Aluminium based metal matrix composites are rapidly developing group of materials due to their unique combination of properties that include low weight, elevated strength, improved wear and corrosion resistance and relatively good ductility. This combination of properties is a result of mixing two groups of materials with rather different properties with aluminium as ductile matrix and different oxides and carbides added as reinforcement. Al2O3, SiC and ZrO2 are the most popular choices of reinforcement material. One of the most common methods for producing this type of metal matrix composites is powder metallurgy since it has many variations and also is relatively low-cost method. Many different techniques of compacting aluminium and ceramic powders have been previously investigated. Among those techniques equal channel angular pressing (ECAP stands out due to its beneficial influence on the main problem that arises during powder compaction and that is a non-uniform distribution of reinforcement particles. This paper gives an overview on ECAP method principles, advantages and produced powder composite properties.

  20. Gating System Design for Casting thin Aluminium Alloy (Al-Si Plates

    Directory of Open Access Journals (Sweden)

    Victor ANJO

    2013-11-01

    Full Text Available The main problems caused by improper gating are entrained aluminium oxide films, cuts and washes, low casting yield and entrapped gas. This study describes the design of a gating system to produce thin Aluminium cast alloy plates of different sizes and thicknesses of 4mm, 6mm, 8mm, and 10mm using the non-pressurized gating with ratio of 1:4:4 and green sand moulding technique. The gating design was based on the laws of fluid mechanics and empirical rules of gating for non ferrous metals. The equipments used for this experiment includes; a coal fired crucible furnace and an X-Ray machine. Materials used include; silica sand, clay, wood, glue and Aluminium alloy scraps. The experimental procedure involved: the gating design calculations, construction of wooden pattern and gating; using the wooden pattern and gating to produce the mould cavities and gating; melting, melt treatment and pouring of melt in the sand mould to produce the casting. The plate castings after removal from mould were visually examined for surface defects and after fettling and cleaning X-Ray radiography was used to find the internal soundness of the castings. From the results obtained in the experiment, it was found that there were no internal defects and quality castings were produced.

  1. Influence of aluminium incorporation on the structure of ZrN films deposited at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Araiza, J J [Unidad Academica de Fisica, Universidad Autonoma de Zacatecas, Paseo a la Bufa esq, Calzada Solidaridad s/n 98060, Zacatecas (Mexico); Sanchez, O [Departamento de Fisica e Ingenieria de Superficies, Instituto de Ciencia de Materiales de Madrid-CSIC, C/ Sor Juana Ines de la Cruz 3, 28049 Cantoblanco, Madrid (Spain)], E-mail: olgas@icmm.csic.es

    2009-06-07

    We have studied the influence of Al incorporation in the crystalline structure of ZrN thin films deposited by dc magnetron sputtering at low temperature. The amount of aluminium in the films depends directly on the power applied to the aluminium cathode during the deposition. Energy dispersive x-ray analysis and x-ray diffraction (XRD) were used to obtain the chemical composition and crystalline structure of the films, respectively. When Al atoms are incorporated into the ZrN coatings, the strong ZrN (2 0 0) orientation is modified by a combination of other ones such as ZrN (1 1 1), Zr{sub 3}N{sub 4} (2 1 1) and hexagonal AlN (1 0 0) as detected from the XRD spectra for high aluminium concentrations. Fourier-transform infrared spectroscopy allowed us to identify oxides and nitrides, ZrO, AlO and AlN, incorporated into the deposited films. The effect of a bias voltage applied to the substrate has also been investigated and related to the changes in the microstructure and in the nanohardness values of the ZrAlN films.

  2. The Macro-Adjustment Policies on China’s Aluminium Industry

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>In recent years, China’s aluminium industry has developed rapidly with considerable expansion of the production scale. Presently, China’s aluminum production capacity has taken a quarter of the world total, and China has become the largest aluminium producer in the world, However, such large scaled expan-

  3. Aluminium based adjuvants and their effects on mitochondria and lysosomes of phagocytosing cells.

    Science.gov (United States)

    Ohlsson, Lars; Exley, Christopher; Darabi, Anna; Sandén, Emma; Siesjö, Peter; Eriksson, Håkan

    2013-11-01

    Aluminium oxyhydroxide, Al(OH)3 is one of few compounds approved as an adjuvant in human vaccines. However, the mechanism behind its immune stimulating properties is still poorly understood. In vitro co-culture of an aluminium adjuvant and the human monocytic cell line THP-1 resulted in reduced cell proliferation. Inhibition occurred at concentrations of adjuvant several times lower than would be found at the injection site using a vaccine formulation containing an aluminium adjuvant. Based on evaluation of the mitochondrial membrane potential, THP-1 cells showed no mitochondrial rupture after co-culture with the aluminium adjuvant, instead an increase in mitochondrial activity was seen. The THP-1 cells are phagocytosing cells and after co-culture with the aluminium adjuvant the phagosomal pathway was obstructed. Primary or early phagosomes mature into phagolysosomes with an internal pH of 4.5 - 5 and carry a wide variety of hydrolysing enzymes. Co-culture with the aluminium adjuvant yielded a reduced level of acidic vesicles and cathepsin L activity, a proteolytic enzyme of the phagolysosomes, was almost completely inhibited. THP-1 cells are an appropriate in vitro model in order to investigate the mechanism behind the induction of a phagocytosing antigen presenting cell into an inflammatory cell by aluminium adjuvants. Much information will be gained by investigating the phagosomal pathway and what occurs inside the phagosomes and to elucidate the ultimate fate of phagocytosed aluminium particles.

  4. Domestic Output of Aluminium Alloy Hub Surpassing 70 million in 2007

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>According to a report from the hub branch of China Association of Automobile Manufactur- ers,China has produced a total of more than 70 million aluminium alloy hubs in 2007,a year- on-year growth over 25%,while consuming over 700,000 tons of primary aluminium the whole year.

  5. The effect of aluminium chlorhydrate on sweat gland activity in cattle.

    Science.gov (United States)

    Rees-Jones, A M; Jenkinson, D M

    1978-03-01

    Topical application of aluminium chlorhydrate had no appreciable antiperspirant action on the epitrichial glands of cattle. There was no evidence of penetration of the salt into the dermis or of any change in the morphology of the glands. It is probable that the antiperspirant activity of aluminium chlorhydrate in the human axilla, is only on the atrichial glands. PMID:632617

  6. Aluminium in an ocean general circulation model compared with the West Atlantic Geotraces cruises

    NARCIS (Netherlands)

    van Hulten, M. M. P.; Sterl, A.; Tagliabue, A.; Dutay, J. -C.; Gehlen, M.; de Baar, H. J. W.; Middag, R.

    2013-01-01

    A model of aluminium has been developed and implemented in an Ocean General Circulation Model (NEMO-PISCES). In the model, aluminium enters the ocean by means of dust deposition. The internal oceanic processes are described by advection, mixing and reversible scavenging. The model has been evaluated

  7. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain. PMID:27515230

  8. Design of an aluminium bicycle path integrated in a steel bridge

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Burggraaf, H.G.

    2007-01-01

    This paper describes the design of the aluminium structure of a bicycle path which is mounted on an existing steel brige. The benefits of aluminium, being low self weight, freedom in design obtained by extrusion and good corrosion resistance were maximal utilized. One of the main drawbacks of alumin

  9. Void formation in pure aluminium irradiated with high-energetic electron beams and gamma-quanta

    DEFF Research Database (Denmark)

    Gan, V. V.; Ozhigou, L. S.; Yamnitsky, V. A.;

    1983-01-01

    The spatial distribution of displaced atoms and helium atoms and also the spectra of damaging energies of primary displaced atoms in a thick aluminium target irradiated with electrons of 225 MeV energy were calculated. Pure aluminium (99.9999%) irradiated up to 0.04 dose was studied by electron...

  10. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    Directory of Open Access Journals (Sweden)

    N. S. Ahmad Zauzi

    2016-01-01

    Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

  11. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-08-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

  12. Fatigue testing of large scale details of a large size aluminium surface effect ship

    NARCIS (Netherlands)

    Dijkstra, O.D.; Vredeveldt, A.W.; Janssen, G.Th.M.; Ortmans, P.

    1998-01-01

    The paper presents the results of two large scale fatigue tests on a detail of an aluminium surface effect ship. The overall dimensions of the specimens were: length 4.8 m, height 3.2 m and width 1.5 m (equal to the main frame spacing). The specimens consist of an aluminium structure of welded plate

  13. Mechanical and frictional behaviour of nano-porous anodised aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Tsyntsaru, N., E-mail: tintaru@phys.asm.md [Institute of Applied Physics of ASM, 5 Academy str., Chisinau, MD 2028 (Moldova, Republic of); Kavas, B., E-mail: bkavas@ford.com.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469 Maslak (Turkey); Ford Otomotiv San A.S., Istanbul (Turkey); Sort, J., E-mail: jordi.sort@uab.cat [Institució Catalana de Recerca i Estudis Avançats (ICREA) and Departament de Física, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); Urgen, M., E-mail: urgen@itu.edu.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469 Maslak (Turkey); Celis, J.-P., E-mail: jean-pierre.celis@mtm.kuleuven.be [KU Leuven, Dept. MTM, Kasteelpark Arenberg 44, B-3001 (Belgium)

    2014-12-15

    The porous structure of anodic aluminium oxide (AAO) can be used in versatile applications such as a lubricant reservoir in self-lubricating systems. Such systems are subjected to biaxial loading, which can induce crack formation and propagation, ultimately leading to catastrophic mechanical failure. In this study, the mechanical and tribological behaviour of AAO, prepared from two different types of electrolytes (sulphuric and oxalic acids), are studied in detail. The electrolytic conditions are adjusted to render highly tuneable average pore diameters (between 16 and 75 nm), with porosity levels ranging from 9% to 65%. Well-ordered porous AAO are produced by two-step anodization at rather low temperatures. Mechanical properties, mainly hardness and Young's modulus, are investigated using nanoindentation. Both the porosity degree and the composition of the electrolytic baths used to prepare the AAO have an influence on the mechanical properties. Ball-on-flat configuration was used to estimate the tribological behaviour under dry conditions. No major cracks were observed by scanning electron microscopy, neither after indentation or fretting tests. In the running-in period of tribology experiments the pores were filled with debris. This was followed by the formation of a highly adherent tribolayer – a third body consisting of fine worn particles originated from both the sample and the counterbody. Pore diameter and porosity percentage are found to strongly affect hardness and Young's modulus, but they do not have a major effect on the frictional behaviour. - Highlights: • Well-ordered porous AAO with pore diameters between 16 and 75 nm were produced. • Porosity and composition of electrolytic baths influence the mechanical properties. • Ball-on-flat configuration was used in tribological testing under dry conditions. • Adherent tribolayer consisting of fine worn particles prevents AAO from cracking. • Testing parameters are moreover essential

  14. Nouveau procédé de synthèse du nitrure d'aluminium

    OpenAIRE

    Haussonne, J.; Lostec, J.; Bertot, J.; Lostec, L.; Sadou, S.

    1993-01-01

    Les calculs thermodynamiques montrent que, même à température ambiante, l'aluminium pur peut réagir avec l'azote pour former le nitrure d'aluminium AlN. Cependant, la poudre d'aluminium pur n'existe pas : ses grains sont toujours entourés d'une couche d'alumine protectrice. De plus, dans l'hypothèse où l'on pourrait faire réagir de la poudre d'aluminium avec de l'azote, il se formerait de même une couche protectrice de nitrure d'aluminium qui empêcherait le centre des grains de réagir. S'insp...

  15. Production and some properties of Si3N4 reinforced aluminium alloy composites

    Directory of Open Access Journals (Sweden)

    Pardeep Sharma

    2015-09-01

    Full Text Available The present research work focuses on the production of aluminium (AA6082-T6 matrix composites reinforced with various weight percentage of silicon nitride particles by conventional stir casting route. The percentage of reinforcement is varied from 0 wt.% to 12 wt.% in a stage of 3%. The microstructures and mechanical properties of the fabricated aluminium matrix composites are investigated. The scanning electron microstructure images reveal the presence of Si3N4 particles in the aluminium matrix. The distribution of Si3N4 particles has also been recognized with X-ray diffraction technique. The mechanical properties such as ultimate tensile strength and hardness have improved at the cost of reduction in ductility with increase in weight percentage of silicon nitride particulates in the aluminium metal matrix. The density and porosity of the composites also show an increasing trend with increase in volume fraction of Si3N4 particles in the aluminium matrix.

  16. Experimental Study on the Shock Absorption Performance of Combined Aluminium Honeycombs under Impact Loading

    Directory of Open Access Journals (Sweden)

    Lei Cao

    2015-01-01

    Full Text Available Shock absorption characteristics of combined aluminium honeycomb structures were studied experimentally. In the experiments, a testing platform was design to compare the shock absorption level of different honeycomb specimens quantitatively. The shock response curves of six test points mounted on the platform were recorded with acceleration sensors when the buffer was impacted by a bullet driven by high pressure gas. The maximum acceleration values in time domain and in specifically spectral domain were obtained based on spectral analysis. Comparing the data of combined aluminium honeycomb buffer and single aluminium honeycomb buffer, conclusion can be obtained that shock absorbing characteristic of combined aluminium honeycomb buffer is better. Furthermore, compression properties of three kinds of buffers were tested under quasi-static state. The energy absorption parameters were calculated. The results show suitable combined aluminium honeycomb buffer can smooth the stress and lower the energy applied to the testing platform.

  17. Low-temperature Electrodeposition of Aluminium from Lewis Acidic 1-Allyl-3-methylimidazolium Chloroaluminate Ionic Liquids

    Institute of Scientific and Technical Information of China (English)

    郑勇; 张锁江; 吕兴梅; 王倩; 左勇; 刘恋

    2012-01-01

    Lewis acidic 1-allyl-3-methylimidazolium chloroaluminate ionic liquids were used as promising electrolytes in the low-temperature electrodeposition of aluminium. Systematic studies on deposition process have been performed by cYClic voltammetry and chronoamperometry. The surface morphology and X-ray diffraction (XRD) patterns of deposits prepared at different experimental conditions were also investigated. It was shown that the nucleation density and growth rate of crystallites had a great effect on the structure of aluminium deposited. The crys- tallographic orientation of deposits was mainly influenced by temperature and current density. Smooth, dense and well adherent aluminium coatings were obtained on copper substrates at 10-25 mA.cm^-2 and 313.2-353.2 K. More- over, the current efficiency of deposition and purity of aluminium have been significantly improved, demonstrating that the ionic liquids tested have a prospectful potential in electroplating and electrorefining of aluminium.

  18. Slip lines in scandium and lithium containing aluminium alloys

    International Nuclear Information System (INIS)

    Intensive slip lines in cold rolled sheets of scandium or lithium containing aluminium base alloys are under study. Slip lines are shown to be the places of concentrated shear strain which arise due to the occurrence of secondary δ'(Al3Li) and Al3Sc particles completely coherent to the matrix. The formation of slip lines has a detrimental effect on cold rolled sheet mechanical properties after heat hardening. To avoid the appearance of slip lines it is necessary to roll sheets with low reductions in area and to choose appropriate conditions of intermediate heat treatments. 5 refs., 5 figs., 2 tabs

  19. Regularities in aluminium and indium chemisorption on chelating polymeric sorbents

    International Nuclear Information System (INIS)

    Complexation properties of synthesized polymer chelate sorbents: substituted of polystyrene-azo-pyrocatechol are investigated and correlations between pK'OH of functional groups of sorbents as well as pH50 values of chelation and constants of stability (lgKstab) are established for studying regularities of effect of structure and acid-base properties of functional groups of sorbents on the parameters of Al3+ and In3+ chemical sorption. Established correlations make it possible to predict the physicochemical parameters of sorbents and sorption of metal ions with the aim of separation and concentration of aluminium and indium micro account from the objects of different origin

  20. Skin telangiectasia in workers of an aluminium processing plant.

    Science.gov (United States)

    Balić, J; Kansky, A

    1988-01-01

    Telangiectases were detected in 57 (46.7%) of 122 workers employed at the electrolysis department of the aluminium plant Lozovac/Sibenik, Yugoslavia. Of 116 workers employed in the smeltery of the same plant, telangiectases were observed in 19 persons (16.4%) and in a group of 121 public transportation workers from Sibenik 15 men (12.4%) displayed enlarged blood vessels. Statistical evaluation revealed the difference in number between workers showing telangiectases engaged in electrolysis and the other two samples to be significant. It may be assumed that telangiectases were caused by hydrogen fluoride and other fluorides. Further clinical parameters, as well as working conditions, are reviewed.

  1. Modeling of recrystallization texture of aluminium: symmetric and asymmetric rolling

    Science.gov (United States)

    Wierzbanowski, K.; Kotra, M.; Wronski, M.; Sztwiertnia, K.; Wronski, S.; Lodini, A.

    2015-04-01

    In some metallic materials the dominating recrystallization mechanism can be described by the oriented growth behaviour. Phenomenological laws state that in selected materials only these nuclei grow intensively which have a given misorientation relation with the deformed matrix. This description is frequently verified in f.c.c. metals and generally reported misorientations correspond approximately to 400 rotation around the axis. Basing on the above ideas the recrystallization model, including the compromise condition, was formulated and applied to the study of recrystallization textures of rolled polycrystalline aluminium.

  2. Spectrum Simulation of Li-Like Aluminium Plasma

    Institute of Scientific and Technical Information of China (English)

    PENG Feng; JIANG Gang; ZHU Zheng-He

    2006-01-01

    X-ray emission spectra for L-shell of Li-like aluminium ions are simulated by using the flexible atomic code based on the collisional radiative model. Atomic processes including radiative recombination, dielectronic recombination, collisional ionization and resonance excitation from the neighbouring ion (Al9+ and Al11+) charge states of the target ion (Al10+) are considered in the model. In addition, the contributions of different atomic processes to the x-ray spectrum are analysed. The results show that dielectronic recombination, radiative recombination, collisional ionization and resonance excitation, other than direct collisional excitation, are very important processes.

  3. Physical model of aluminium refining process in URC-7000

    Directory of Open Access Journals (Sweden)

    M. Saternus

    2009-07-01

    Full Text Available The paper presents short characteristics of the most frequently used reactors for the continuous refining of aluminium and its alloys. Refining depends on the flow rate of refining gas. It influences the shape and size of gas bubbles. So the physical model was created to determine the level of gas bubble dispersion in liquids. Schemes of gas dispersion in liquid metal were presented taking into consideration that the gas flow rate is changing from 2 to 30 dm3/min. The range selection of the flow rate of refining gas value for five patterns of the dispersion (no dispersion, minimum, intimate, uniform and overdispersion was also done.

  4. Interface reaction in aluminium matrix composite at laser welding

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Interface reaction of SiCw/6061Al aluminium matrix composite subjected to laser welding was studied. It is pointed out that the main reason for bad weldability of the material is concerned with the interface reaction during the welding. Effects of welding parameters on interface reaction were also investigated. The results show that the interface bonding state can be improved by laser beam, and the main welding parameter affecting the strength of weld is laser output power. The smaller the output power, the lower the extent of interface reaction and the better the mechanical properties.

  5. Design considerations for HFQ® hot stamped aluminium structural panels

    Directory of Open Access Journals (Sweden)

    Foster Alistair

    2015-01-01

    Full Text Available HFQ is a deep drawing process for alloyed aluminium sheet that can be used to produce complex-stamped forms while maintaining the high-strength of 6xxx and 7xxx alloys. By adopting a strategy to design for HFQ at the platform level, designers can reduce part count (thereby reducing cost and weight, reduce gauge (thereby reducing weight, and improve part packaging. Two simple design examples are given to assist designers in evolving traditionally formed panel designs to HFQ formed solutions. Example features are used to illustrate the effect of geometry, thickness and strength on the final structural component.

  6. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    OpenAIRE

    Aggerbeck, Martin; Ambat, Rajan

    2014-01-01

    I dette projekt blev muligheden for at designe aluminiumsbaserede coatings undersøgt med fokus på hvordan den kemiske sammensætning og overfladens beskaffenhed påvirker den visuelle fremtoning og de basiske korrosionsegenskaber med titan anvendt som det primære legeringselement. De primære resultater og diskussioner fra dette arbejde præsenteres i form af i bilag som fire artikelmanuskripter indsendt til publikation i tidsskrifter. Anvendelsen af aluminium er bred, fra transportmidler, bygnin...

  7. Optically Designed Anodised Aluminium Surfaces: Microstructural and Electrochemical Aspects

    DEFF Research Database (Denmark)

    Gudla, Visweswara Chakravarthy

    under high frequency anodising, highly reflecting, bright and glossy white anodised aluminium surfaces were generated for the first time. Further, these white anodised surfaces were conventionally dyed to generate new appearances based on pastel colours. The work presented in this thesis is mainly......-13). The outcome of the work is presented in the last chapter (Chapter 15). The results from white anodising of the Al surfaces, which is the primary goal of this thesis and also the generation of a new set of pastel coloured anodised surfaces is presented. The optical characterization of these white anodised...

  8. Release Behaviour of Shock Loaded LY12 Aluminium Alloy

    Institute of Scientific and Technical Information of China (English)

    YAN Min; DAI Lan-Hong; SHEN Le-Tian

    2005-01-01

    @@ By making use of a light gas gun, a specially designed target is impacted by the LY12 flyer, and the pressure is taken in the range of 0.6-3 GPa. Based on the stress profiles measured in the buffer materials by manganese gauges, the Hugoniot curve and release curves of LY12 aluminium alloy are obtained. Meanwhile, the release curves from different initial shocked states are described in both the pressure-particle velocity plane and the pressure-specific volume plane.

  9. Multi-element study in aluminium by activation analysis technique

    International Nuclear Information System (INIS)

    The instrumental activation analysis is a technique relatively quickly that help to know the elemental composition of materials. It is used mainly in the trace elements determination but in the case of major elements it is necessary to make some considerations as the different nuclear reactions carried out due to the neutron flux is a mixture of thermal and fast neutrons. This could be interpreted for the presence and or erroneous quantification about some elements. In this work, is described the way in which was analyzed a container piece with approximately a 85% of aluminium. The elements Zn, Mn, Sb, Ga, Cu, Cl and Sm were determined. (Author)

  10. Bone histoquantitative findings and histochemical staining reactions for aluminium in chronic renal failure patients treated with haemodialysis fluids containing high and low concentrations of aluminium.

    OpenAIRE

    McClure, J; Fazzalari, N L; Fassett, R G; Pugsley, D. J.

    1983-01-01

    A total of 112 undecalcified bone biopsies from 67 patients under treatment for chronic renal failure by maintenance haemodialysis was available for retrospective study. The patients were divided into three groups. Group I (15 cases) had been dialysed for the majority of the time in their own homes with a fluid containing a low concentration of aluminium. Group II (28 cases) had been dialysed exclusively in hospital (prior to 1978) with a fluid containing a high concentration of aluminium and...

  11. 铝合金芯高导电率铝绞线标准解读%A Reading of High Conductivity Aluminium Conductor Aluminium Alloy Reinforced Standard

    Institute of Scientific and Technical Information of China (English)

    万建成; 董玉明; 刘龙

    2014-01-01

    To implement the engineering philosophy of security, reliability, reasonable economy, advanced technology and environmental friendliness, company standard of State Grid, 《High Conductivity Aluminium Conductor Aluminium Alloy Reinforced》, has been finished. A detailed reading about the technical approaches, basic principle and announcements of high conductivity aluminium conductor aluminium alloy reinforced standard is given by combining corresponding research results. The implementation of the standard provides important basis to guide the engineering application of high conductivity aluminium conductor aluminium alloy reinforced and will promote the upgrading of conductors for overhead transmission lines.%贯彻安全可靠、经济合理、技术先进、环境友好的技术原则,完成国家电网公司企业标准《铝合金芯高导电率铝绞线》的制定工作。结合铝合金芯高导电率铝绞线相应研究成果,解读主要条款的编制思路、基本原理以及注意事项。该标准的实施为指导铝合金芯高导电率铝绞线工程应用提供重要依据,并将促进架空输电线路用导线的更新换代。

  12. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Horsewell, Andy; Sommer, W. F.;

    1986-01-01

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg(AlMg3) and Al-1.1%Mg-0.5%Si(Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-100°C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) sho...... higher than in the pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure...

  13. The determination of boron in aluminium of high purity

    International Nuclear Information System (INIS)

    A description is given of the investigations that led to the development of chemical methods for the determination of boron within the range 0,25 to 1,0 p.p.m. in aluminium of high purity. Methods were developed that incorporated fluorimetry, directly in solutions containing aluminium and after separation of boron by liquid-liquid extraction into 2-ethyl-1,3 hexanediol. A published spectrophotometric method, involving extraction of the BF4sup(-) complex with methylene blue into dichloroethane, was modified for application to alluminium samples. Details of this modified procedure and the fluorimetric-extraction procedure are appended. The precision of the methylene-blue method is about 6 percent relative and is recommended for precision and speed in preference to others. Separation of boron by distillation and spectrophotometric determination with curcumin gave low values in comparison with those obtained by the other methods. Agreement between the boron values obtained on the samples tested was good for the fluorimetric and methylene-blue spectrophotometric methods

  14. Aluminium surface treatment with ceramic phases using diode laser

    Science.gov (United States)

    Labisz, K.; Tański, T.; Brytan, Z.; Pakieła, W.; Wiśniowski, M.

    2016-07-01

    Ceramic particles powder feeding into surface layer of engineering metal alloy is a well-known and widely used technique. New approach into the topic is to obtain finely distributed nano-sized particles involved in the aluminium matrix using the traditional laser technology. In this paper are presented results of microstructure investigation of cast aluminium-silicon-copper alloys surface layer after heat treatment and alloying with ceramic carbides of WC and ZrO2 using high-power diode laser. The surface layer was specially prepared for the reason of reducing the reflectivity, which is the main problem in the up-to-date metal matrix composites production. With scanning electron microscopy, it was possible to determine the deformation process and distribution of WC and ZrO2 ceramic powder phase. Structure of the surface after laser treatment changes, revealing three zones—remelting zone, heat-affected zone and transition zone placed over the Al substrate. The structural changes of ceramic powder, its distribution and morphology as well as microstructure of the matrix material influence on functional properties, especially wear resistance and hardness of the achieved layer, were investigated.

  15. Geopolymerisation of fly ashes with waste aluminium anodising etching solutions.

    Science.gov (United States)

    Ogundiran, M B; Nugteren, H W; Witkamp, G J

    2016-10-01

    Combined management of coal combustion fly ash and waste aluminium anodising etching solutions using geopolymerisation presents economic and environmental benefits. The possibility of using waste aluminium anodising etching solution (AES) as activator to produce fly ash geopolymers in place of the commonly used silicate solutions was explored in this study. Geopolymerisation capacities of five European fly ashes with AES and the leaching of elements from their corresponding geopolymers were studied. Conventional commercial potassium silicate activator-based geopolymers were used as a reference. The geopolymers produced were subjected to physical, mechanical and leaching tests. The leaching of elements was tested on 28 days cured and crushed geopolymers using NEN 12457-4, NEN 7375, SPLP and TCLP leaching tests. After 28 days ambient curing, the geopolymers based on the etching solution activator showed compressive strength values between 51 and 84 MPa, whereas the commercial potassium silicate based geopolymers gave compressive strength values between 89 and 115 MPa. Based on the regulatory limits currently associated with the used leaching tests, all except one of the produced geopolymers (with above threshold leaching of As and Se) passed the recommended limits. The AES-geopolymer geopolymers demonstrated excellent compressive strength, although less than geopolymers made from commercial activator. Additionally, they demonstrated low element leaching potentials and therefore can be suitable for use in construction works.

  16. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    Directory of Open Access Journals (Sweden)

    Hamilta de Oliveira Santos

    2005-06-01

    Full Text Available Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken from a billet of an experimental alloy (alloy 1 and were subsequently hot-rolled and cold-rolled (height reduction, 72% and 70%, respectively. The other used samples, alloys 2 and 3, were taken from cylinders liners. The results from the Laue camera showed texture just in the axial direction of alloy 3. The pole figures also indicated the presence of a typical low intensity deformation texture, especially for alloy 3. The spray formed microstructure, which is very fine, hinders the Al-Si texture formation during mechanical work.

  17. Cancellous bone homograft storage with aluminium-polyethylene bags.

    Science.gov (United States)

    Meana, A; Martinez, R; Cañal, P; Arriaga, M J; Román, F San; Llames, S; Orós, C; Moreno, A; Fernandez, C

    2006-01-01

    In order to transport and cryopreserve human tissues, it is essential to have an easy-to-use recipient where tissues can be kept in sterile conditions. Here we show the results obtained by using Macopharma's tissue freezing bags, an aluminium-polyethylene multilayer bag, in our tissue bank of the Centro Comunitario de Sangre y Tejidos de Asturias. Five hundred and twenty-seven cancellous bone homografts were obtained from hospitals located 120 km around our Bank. The homografts were submitted to bacteriological controls and sent to our bank in these bags. They were stored at -70 degrees C and sent in dry ice to about 50 hospitals, where the tissue was bacteriologically controlled and grafted. Furthermore, the behaviour of these bags at -140 degrees C (vapour nitrogen) or -196 degrees C (liquid nitrogen) was tested. Our results indicate that Macopharma aluminium-polyethylene bags are suitable for the transporting and cryopreserving of cancellous bone homografts. These bags could also be used for keeping tissues in nitrogen containers.

  18. A 3D printed superconducting aluminium microwave cavity

    Science.gov (United States)

    Creedon, Daniel L.; Goryachev, Maxim; Kostylev, Nikita; Sercombe, Timothy B.; Tobar, Michael E.

    2016-07-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals, in particular, has found a number of applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Although many techniques are used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a microwave cavity (resonant frequencies 9.9 and 11.2 GHz) 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable with the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum electrodynamics experiments. The result is achieved even with a very large concentration of non-superconducting silicon in the alloy of 12.18%, compared with Al-6061, which has between 0.4% and 0.8%. Our results may pave the way for the possibility of 3D printing superconducting cavity configurations that are otherwise impossible to machine.

  19. A 3D Printed Superconducting Aluminium Microwave Cavity

    CERN Document Server

    Creedon, Daniel L; Kostylev, Nikita; Sercombe, Tim; Tobar, Michael E

    2016-01-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals in particular has found a number of novel applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Whilst many techniques can be used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a resonant microwave cavity 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable to the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum...

  20. Experimental study of friction in aluminium bolted joints

    Directory of Open Access Journals (Sweden)

    Vincenzi N.

    2010-06-01

    Full Text Available This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces versus sixth tightening (spoiled surfaces. The study considers M8x1.25 8.8 galvanized screws.

  1. Modelling of semi-liquid aluminium flow in extrusion

    Directory of Open Access Journals (Sweden)

    G. Skorulski

    2007-04-01

    Full Text Available characterizing by low cost. The significant results may be quickly applying using theory of probability. The way of modelling the deformation mechanisms during extrusion of aluminium alloys in semi - liquid phase, the way of preparing samples and experimental technique has been analysed in the following work. On the ground of received results (i.e. registrations of consecutive process steps the grid of the flow velocity vectors on a flat sample surface was done. It allowed to draw conclusions which one of the basic deformation mechanisms is dominant in particular stage of the process. The technique of measurement has been shown as well. Experiments are made using plasticine and rape oil as a substiute materials. Some kind of different variants have been investigated. To ensure that such model experiments provide useful information it is essential to select model materials and prepare samples that would exhibit (preferably at room temperature similar behaviour and similar deformation mechanisms as those present during the actual deformation process of aluminium alloys in a semi-liquid state. In particular the FLS, SS and PDS mechanisms should be adequately reproduced.

  2. Effect of aluminium on in vitro rooting of birch (Betula pendula Roth. and poplar (Populus tremula L. x P. alba L. microcuttings

    Directory of Open Access Journals (Sweden)

    Krystyna Bojarczuk

    2014-02-01

    Full Text Available Poplar (Populus tremula L. x P. alba L. and birch (Betula pendula Roth. microcuttings obtained from in vitro cultures on media with aluminium (Al+ or without aluminium (Al- were rooted in perlite saturated with a liquid 1/4 MS medium. Aluminium was added to the rooting medium in the form of aluminium sulphate or aluminium chloride. In the control, i.e. in the medium without aluminium, Al+ and Al- shoots usually developed similarly. Addition of aluminium to the rooting medium had a negative effect on the development of adventitious roots. Poplar and birch shoots obtained from cultures on media with aluminium (AI+ were distinguished by a greater tolerance of aluminium in the medium than shoots obtained from cultures on media without aluminium (A1-.

  3. Derivation of a water quality guideline for aluminium in marine waters.

    Science.gov (United States)

    Golding, Lisa A; Angel, Brad M; Batley, Graeme E; Apte, Simon C; Krassoi, Rick; Doyle, Chris J

    2015-01-01

    Metal risk assessment of industrialized harbors and coastal marine waters requires the application of robust water quality guidelines to determine the likelihood of biological impacts. Currently there is no such guideline available for aluminium in marine waters. A water quality guideline of 24 µg total Al/L has been developed for aluminium in marine waters based on chronic 10% inhibition or effect concentrations (IC10 or EC10) and no-observed-effect concentrations (NOECs) from 11 species (2 literature values and 9 species tested including temperate and tropical species) representing 6 taxonomic groups. The 3 most sensitive species tested were a diatom Ceratoneis closterium (formerly Nitzschia closterium; IC10 = 18 µg Al/L, 72-h growth rate inhibition) aluminium forms of aluminate (Al(OH4 (-) ) and aluminium hydroxide (Al(OH)3 (0) ) although both dissolved, and particulate aluminium contributed to toxicity in the diatom Minutocellus polymorphus and green alga Dunaliella tertiolecta. In contrast, aluminium toxicity to the green flagellate alga Tetraselmis sp. was the result of particulate aluminium only. Four species, a brown macroalga (Hormosira banksii), sea urchin embryo (Heliocidaris tuberculata), and 2 juvenile fish species (Lates calcarifer and Acanthochromis polyacanthus), were not adversely affected at the highest test concentration used.

  4. Factors affecting the aluminium content of human femoral head and neck.

    Science.gov (United States)

    Zioła-Frankowska, Anetta; Dąbrowski, Mikołaj; Kubaszewski, Łukasz; Rogala, Piotr; Frankowski, Marcin

    2015-11-01

    Tissues for the study were obtained intraoperatively during hip replacement procedures from 96 patients. In all the cases, the indication for this treatment was primary or secondary degenerative changes in the hip joint. The subject of the study was the head and neck of the femur, resected in situ. Aluminium concentrations measured in femoral head and neck samples from patients aged between 25 and 91 were varied. Statistical methods were applied to determine the variations in relation to the parameters from the background survey. Significant differences in the aluminium content of femoral head samples were observed between patients under and over 60 years of age. Based on the results, it was confirmed that the aluminium accumulates in bones over a lifetime. The study showed that the content of aluminium in the head and neck of the femur depends on the factors such as: type of medicines taken, contact with chemicals at work, differences in body anatomy and sex. The study on the levels of aluminium in bones and the factors affecting its concentration is a valuable source of information for further research on the role of aluminium in bone diseases. Based on the investigations, it was found that the GF-AAS technique is the best analytical tool for routine analysis of aluminium in complex matrix samples. The use of femoral heads in the investigations was approved by the Bioethics Committee of the University of Medical Sciences in Poznań (Poland).

  5. Increased absorption of aluminium from a normal dietary intake in dementia.

    Science.gov (United States)

    Roberts, N B; Clough, A; Bellia, J P; Kim, J Y

    1998-02-15

    Serum aluminium was significantly raised (p dementia including Alzheimers Disease (AD) 0.66 +/- 0.2 (mumol/l mean +/- 1 s.d.) and patients on regular aluminium hydroxide therapy 0.54 +/- 0.17, compared with healthy volunteers 0.21 +/- 0.13, although not as high as in patients with end stage renal failure on regular dialysis 0.88 +/- 0.42. The urine outputs (mumol/l mean +/- 1 s.d.) of aluminium and silicon, respectively, were also significantly increased up to 5-fold in dementia 2.89 +/- 1.78 (n = 23) and 1587 +/- 645 (n = 22) and patients on regular aluminium hydroxide therapy 5.03 +/- 2.08 (n = 8) and 998 +/- 364 (n = 21) compared with healthy volunteers 0.95 +/- 0.82 (n = 84) and 471 +/- 332 (n = 114). The increase in urine aluminium was thus associated with a similarly marked increase in the output of silicon. The increased absorption of aluminium in dementia patients is equivalent to the intestinal loading in Aludrox therapy. Also silicon appears to be important in the renal excretion of the absorbed aluminium. Whether this is a phenomenon related to the elderly or the process of dementia warrants further study.

  6. Determination of local material properties of laser beam welded aluminium-steel and aluminium-titanium compounds

    Energy Technology Data Exchange (ETDEWEB)

    Hunkel, M.; Hehl, A. von [IWT Stiftung Institut fuer Werkstofftechnik Bremen (Germany); Barr, A.

    2012-04-15

    The combination of different metallic materials, such as aluminium and steel or aluminium and titanium, by firmly bonding via laser beam welding enables the production of customised hybrid lightweight designs with enhanced properties. Both weld geometry and local material behaviour, which are responsible for the final load characteristics of the compound, are influenced by the process parameters during welding. A novel approach of coupling process, microstructure and mechanical simulation, considering the development of weld geometry and local material conditions is intended to deliver a fast and reliable method for evaluating the quasi-static strength of laser beam welded hybrid compounds. Besides the objective to promote a reduction of expensive welding experiments, the developed method can enhance the performance of hybrid structures as well as their lightweight potential for automotive and aircraft applications. The experimental determination of the local mechanical properties as the basis for the regarded simulation approach is an essential part of a running research project. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Aluminium exposure from parenteral nutrition in preterm infants and later health outcomes during childhood and adolescence.

    Science.gov (United States)

    Fewtrell, Mary S; Edmonds, Caroline J; Isaacs, Elizabeth; Bishop, Nick J; Lucas, Alan

    2011-08-01

    Aluminium is the most common metallic element, but has no known biological role. It accumulates in the body when protective gastrointestinal mechanisms are bypassed, renal function is impaired, or exposure is high - all of which apply frequently to preterm infants. Recognised clinical manifestations of aluminium toxicity include dementia, anaemia and bone disease. Parenteral nutrition (PN) solutions are liable to contamination with aluminium, particularly from acidic solutions in glass vials, notably calcium gluconate. When fed parenterally, infants retain >75% of the aluminium, with high serum, urine and tissue levels. Later health effects of neonatal intravenous aluminium exposure were investigated in a randomised trial comparing standard PN solutions with solutions specially sourced for low aluminium content. Preterm infants exposed for >10 d to standard solutions had impaired neurologic development at 18 months. At 13-15 years, subjects randomised to standard PN had lower lumbar spine bone mass; and, in non-randomised analyses, those with neonatal aluminium intake above the median had lower hip bone mass. Given the sizeable number of infants undergoing intensive care and still exposed to aluminium via PN, these findings have contemporary relevance. Until recently, little progress had been made on reducing aluminium exposure, and meeting Food and Drug Administration recommendations (<5 μg/kg per d) has been impossible in patients <50 kg using available products. Recent advice from the UK Medicines and Healthcare regulatory Authority that calcium gluconate in small volume glass containers should not be used for repeated treatment in children <18 years, including preparation of PN, is an important step towards addressing this problem.

  8. Anti-corrosive Conversion Coating on Aluminium Alloys Using High Temperature Steam

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    extensively. Despite the intense research no equivalent substitute for (CrCCs) has been found. For these reasons, alternative conversion coatings are sought for substituting existing ones. Aluminium alloys AA 1090, Peraluman 706, and AA 6060 were subjected to high pressure steam treatment and various......-SEM, XRD, and FTIR. Potentiodynamic polarization measurements and acid salt spray testing were used to study the corrosion behavior of the produced coatings. In average, thickness of the oxide layer formed was increased to ~1-1.5 µm with steam treatment and various chemistries, and the coverage...

  9. Combustion characteristics of aluminium-iron oxidein SHS-gravitational process

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In order to get high quality of products, the combustion of aluminium-iron oxide thermite in SHS-gravitational process must be under control. The effects of thermite filling density, hole in thermite and inclined angle of pipe on combustion rate were studied. It shows that the combustion rate decreases with the decrease of filling density. The thermite combusts downwards the pipe much more quickly if there are holes in the thermite. And the combustion rate increases with the increase of the inclined angle of pipe. The experiment results show that the combustion of thermite is predominantly controlled by gas phasereaction, which is attributed to the high temperature of the thermitecombustion.

  10. Developments in electrode materials and electrolytes for aluminium-air batteries

    OpenAIRE

    Egan, D; Ponce De Leon, Carlos; R.J.K. Wood; Jones, R. L.; Stokes, K.R.; Walsh, F. C.

    2013-01-01

    Aluminium-air cells are high-energy density (< 400 W h kg-1), primary batteries first developed in the 1960s. The review shows how the performance of the battery is influenced by the choice of materials, including the type of aluminium alloy, oxygen reduction catalyst and electrolyte type. Two continuing issues with these batteries are (a) the parasitic corrosion of the aluminium, at open-circuit and under discharge, due to the reduction of water on the anode surface and (b) the passive hydro...

  11. The aluminium content of breast tissue taken from women with breast cancer.

    Science.gov (United States)

    House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

    2013-10-01

    The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

  12. The Major Events of China’s Aluminium Industry in 2005

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>The year 2005 is seen as a turning point for China’s aluminium industry with the whole industry making losses leading to the closures, reorganization and acquisitions of the smelters. The macro-adjustment policies of the government on the aluminium industry and the industry’s operating difficulties led to the overall change of the industry, which is reflected by the strengthened position of China’s aluminium industry in the world and China’s influence on the world market is growing with the united

  13. Étude par spectrométrie auger d'alliages aluminium-cuivre liquides

    Science.gov (United States)

    Laty, P.; Joud, J. C.; Desré, P.

    1981-03-01

    Surface analysis of liquid aluminium and aluminium-copper alloys have been performed by Auger electron spectroscopy at 775°C. Experiments were carried out, in UHV chamber, on liquid droplets located in graphite crucible heated by a heat pipe. Pure aluminium has been studied in view to estimate surface contamination. For each Al-Cu alloy surface composition is calculated from the Auger spectra. Peak to peak height ratios are deduced from limited extrapolation t zero level contamination. The deduced Al enrichment of the surface is compared with thermodynamical computation based on statistical model or Gibbs' adsorption relation.

  14. Influence of Aluminium on Performance of HTPB-based Aluminised PBXs

    Directory of Open Access Journals (Sweden)

    Vinay Prakash

    2004-10-01

    Full Text Available The paper describes the development of aluminised plastic-bonded explosives (PBXs based on aluminium and nitramine explosives using hydroxy-terminated polybutadiene as polymer matrix. The PBXs were processed as per standard procedures. Compositions with different formulations were prepared by varying the percentages of aluminium and RDX and their explosive properties, including velocity of detonation (VOD, peak overpressure, duration, impulse and sensitivity to different types of stimuli, were studied. The experimental and theoretical values of the VOD have been compared. It is observed that about 15 per cent aluminium content in the aluminised PBXs shows the optimum VOD.

  15. Bioavailability and Toxicity of Aluminium to the Freshwater Crayfish, Pacifastacus leniusculus

    OpenAIRE

    Woodburn, Katie

    2012-01-01

    Aluminium is found in large amounts all over the world but plants and animals have no use for this metal. However, because it is everywhere, aluminium can get into animals and stops cells, tissues and organs from working properly. The aim of this thesis was to look at where aluminium goes when it is eaten by crayfish and whether it causes any damage to body systems such as the digestive system and the nervous system. Crayfish are freshwater crustaceans; they have a hard outer exoskeleton and ...

  16. Microscopic observation of pattern attack by aggressive ions on finished surface of aluminium alloy sacrificial anode

    International Nuclear Information System (INIS)

    This paper presents the results of a microscopic observation on submerged finished surface of aluminium alloy sacrificial anode. Experimental tests were carried out on polished surface aluminium anode exposed to seawater containing aggressive ions in order to observe of pattern corrosion attack on corroding surface of anode. Results have shown, at least under the present testing condition, that surface of sacrificial anode were attack by an aggressive ion such as chloride along grain boundaries. In addition, results of microanalysis showed that the corrosion products on surface of aluminium alloy have Al, Zn and O element for all sample and within the pit was consists of Al, Zn, O and Cl element. (author)

  17. Dissolved aluminium in the surface microlayer of the eastern Arabian Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Narvekar, P.V.; Singbal, S.Y

    -94 85 Elsevier Science Publishers B.V., Amsterdam Dissolved aluminium in the surface microlayer of the eastern Arabian Sea P.V. Narvekar and S.Y.S. Singbal National Institute of Oceanography, Dona Paula, Goa 403 004, India (Received 5 November 1991...; revision accepted 26 August 1992) ABSTRACT Narvekar, P.V. and Singbal, S.Y.S., 1993. Dissolved aluminium in the surface microlayer of the eastern Arabian Sea. Mar. Chem., 42: 85-94. Measurements of dissolved aluminium (A1) in surface microlayer (SML...

  18. The aluminium content of breast tissue taken from women with breast cancer.

    Science.gov (United States)

    House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

    2013-10-01

    The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

  19. Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

    CERN Document Server

    Sinou, Jean-Jacques

    2008-01-01

    For a car manufacturer, reducing the weight of vehicles is an obvious aim. Replacing steel by aluminium moves towards that goal. Unfortunately, aluminium's stamping numerical simulation results are not yet as reliable as those of steel. Punch-strength and spring-back phenomena are not correctly described. This study on aluminium validates the behaviour law Hill 48 quadratic yield criterion with both isotropic and kinematic hardening. It is based on the yield surface and on associated experimental tests (uniaxial test, plane tensile test, plane compression and tensile shearing).

  20. Emeraldine base as corrosion protective layer on aluminium alloy AA5182, effect of the surface microstructure

    DEFF Research Database (Denmark)

    Cecchetto, L; Ambat, Rajan; Davenport, A.J.;

    2007-01-01

    AA5182 aluminium alloy cold rolled samples were coated by thin Wlms of emeraldine base (EB) obtained from a 5% solution in N-methylpyrrolidinone. Accelerated corrosion tests prove this coating very eVective for corrosion protection of aluminium alloys in neutral environment. This study underlines......: • a weak redox activity of the polymer which passivate the metal, • a proton involving self-healing process taking place at the polymer–metal interface, which contributes to delay local acidiWcation in Wrst steps of corrosion on EB coated aluminium surfaces....