WorldWideScience

Sample records for aluminium 25 target

  1. What does a 0.25-yuan Rise of Retail Electricity Price Mean to Aluminium Enterprises?

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>According to the notification of the National Development and Reform Commission,starting form July 1,2008,the retail electricity price of the nation’s province-level power grids (exclud- ing Tibet Autonomous Region) will rise by 0.25 yuan per kwh averagely.The notification was followed by a series of price-rise plans from the nation’s provinces,cities and autono- mous regions(see Table 1).The price jump is an important measure taken to ensure the coun- try’s economic stability and energy safety. However,it is bad news for the aluminium in- dustry.

  2. Emission pattern of an aluminium nitride target for radio frequency magnetron sputtering

    International Nuclear Information System (INIS)

    Thin amorphous aluminium nitride films, (a-AlN) have been produced by radio frequency magnetron sputtering at rf power 120W from a highly pure AlN target. The target is mounted below the substrate holder such that its position can be adjusted inside the vacuum chamber. The emission pattern is determined by means of thickness distribution of the deposited material obtained from optical transmission measurements. Holding a set of the process parameters constant and only varying the target-sample distance a three dimensional emission pattern of the AlN target was determined. The deposition rate and emission pattern for 120W and 180W (studied before) were compared. This comparison allows us to consider the target and shielding dimensions of our magnetron to predict the thickness and the sputtering rate distribution for any process parameter and sample target geometry.

  3. Plasma production on exposure of an aluminium target to a CO2 laser radiation pulse

    International Nuclear Information System (INIS)

    A theoretical model of plasma formation under the interaction between the CO2 laser radiation and an aluminium target in the air includes heating and evaporation of the target, absorption of the laser radiation in vapors the state of which is described by a two-temperature gas-dynamic approximation. Experimental shapes are used of the laser radiation pulse in the intensity range of 1-400 MW/cm2 with duration of 0.01-10 μs. Calculated times of plasma formation are in agreement with experimental data especially if possible existence of thermally insulated microregions on the exposed surface is taken into account

  4. Reactive sputter deposition of Al doped TiOx thin films using titanium targets with aluminium inserts

    International Nuclear Information System (INIS)

    Highlights: •Ti(Al)Ox thin films with varying Al fractions and increasing discharge current were deposited. •The reactive sputtering behaviour of Ti targets with Al inserts was studied. •XPS and EDX were used to check the stoichiometry of the films. •Optical transmittance measurements were performed to determine the band gap. -- Abstract: Al doped TiOx thin films were deposited using Ti targets with Al inserts. Both the effect of the number of aluminium inserts and the discharge current on the discharge voltage, on the aluminium content in the thin films, and on the reactive sputtering behaviour was investigated. The aluminium content in the film was measured using X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX). X-ray diffraction (XRD) revealed that the as-deposited thin films were amorphous, independent of the aluminium content or the discharge current. The XPS results indicated that the oxide films were substoichiometric. The optical band gap of the Ti(Al)Ox thin films was investigated as a function of the aluminium concentration and the discharge current. The addition of aluminium results in a significant increase of the band gap at low discharge currents, while no significant influence on the band gap was found at higher currents

  5. Structure and corrosion resistance of aluminium AlMg2.5; AlMg5Mn and AlZn5Mg1 alloys

    Directory of Open Access Journals (Sweden)

    J. Szewczenko

    2010-07-01

    Full Text Available Purpose: The aim of the work was the evaluation of corrosion resistance and structure of aluminium AlMg2.5; AlMg5Mn and AlZn5Mg1 alloys.Design/methodology/approach: The corrosion resistance tests of investigated alloys were carried out by means of potentiodynamic method registering anodic polarization curves in 3.5% NaCl solution at room temperature. Registering anodic polarization curves was conducted at the potential rate equal to 1mV/s. As the reference electrode was used saturated calomel electrode (SCE and the auxiliary electrode was platinum electrode. Mechanical properties were evaluated on the basis of Vickers hardness test. The test was realized with the use of Hauser hardness tester. The observations of the surface morphology after corrosive tests were carried out using Digital Scanning Electron Microscope DSM 940 OPTON.Findings: The investigations of corrosion resistance of examined aluminium alloys shows that the highest corrosion resistance in 3.5% NaCl solution was observed for AlZn5Mg1 aluminium alloy.Practical implications: The obtained results can be used for searching the appropriate way of improving the corrosion resistance of analysed alloys because better corrosion resistance, lightweight of aluminium and its alloys makes them as most attractive for the steel replacement in shipbuilding.Originality/value: The corrosion behaviour in chloride solution of AlMg2.5; AlMg5Mn and AlZn5Mg1 alloys was investigated.

  6. The toxicity of aluminium in humans.

    Science.gov (United States)

    Exley, C

    2016-06-01

    We are living in the 'aluminium age'. Human exposure to aluminium is inevitable and, perhaps, inestimable. Aluminium's free metal cation, Alaq(3+), is highly biologically reactive and biologically available aluminium is non-essential and essentially toxic. Biologically reactive aluminium is present throughout the human body and while, rarely, it can be acutely toxic, much less is understood about chronic aluminium intoxication. Herein the question is asked as to how to diagnose aluminium toxicity in an individual. While there are as yet, no unequivocal answers to this problem, there are procedures to follow to ascertain the nature of human exposure to aluminium. It is also important to recognise critical factors in exposure regimes and specifically that not all forms of aluminium are toxicologically equivalent and not all routes of exposure are equivalent in their delivery of aluminium to target sites. To ascertain if Alzheimer's disease is a symptom of chronic aluminium intoxication over decades or breast cancer is aggravated by the topical application of an aluminium salt or if autism could result from an immune cascade initiated by an aluminium adjuvant requires that each of these is considered independently and in the light of the most up to date scientific evidence. The aluminium age has taught us that there are no inevitabilities where chronic aluminium toxicity is concerned though there are clear possibilities and these require proving or discounting but not simply ignored. PMID:26922890

  7. Aluminium and human breast diseases.

    Science.gov (United States)

    Darbre, P D; Pugazhendhi, D; Mannello, F

    2011-11-01

    The human breast is exposed to aluminium from many sources including diet and personal care products, but dermal application of aluminium-based antiperspirant salts provides a local long-term source of exposure. Recent measurements have shown that aluminium is present in both tissue and fat of the human breast but at levels which vary both between breasts and between tissue samples from the same breast. We have recently found increased levels of aluminium in noninvasively collected nipple aspirate fluids taken from breast cancer patients (mean 268 ± 28 μg/l) compared with control healthy subjects (mean 131 ± 10 μg/l) providing evidence of raised aluminium levels in the breast microenvironment when cancer is present. The measurement of higher levels of aluminium in type I human breast cyst fluids (median 150 μg/l) compared with human serum (median 6 μg/l) or human milk (median 25 μg/l) warrants further investigation into any possible role of aluminium in development of this benign breast disease. Emerging evidence for aluminium in several breast structures now requires biomarkers of aluminium action in order to ascertain whether the presence of aluminium has any biological impact. To this end, we report raised levels of proteins that modulate iron homeostasis (ferritin, transferrin) in parallel with raised aluminium in nipple aspirate fluids in vivo, and we report overexpression of mRNA for several S100 calcium binding proteins following long-term exposure of MCF-7 human breast cancer cells in vitro to aluminium chlorhydrate. PMID:22099158

  8. Mechanism of Nickel-Aluminium Alloy Electroplating

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The effect of operating conditions on the aluminium content of Ni-Al alloy deposit and the catalytic function of NaF on electrodeposition in the nonaqueous solution containing aluminium are investigated.The results indicate that the plated aluminuim content will be increased with the rise of current density in a given range.When the current density is 2.5A/dm2,nickle-aluminium alloy containing 13.1 wt% aluminium will be deposited.The plated aluminium content will be increased by 2wt% as 0.1mol/L NaF is added to the bath.

  9. The evolution of melasma therapy: targeting melanosomes using low-fluence Q-switched neodymium-doped yttrium aluminium garnet lasers.

    Science.gov (United States)

    Kauvar, Arielle N B

    2012-06-01

    Melasma is an acquired disorder of pigmentation that commonly affects women with phototypes III-V, and it has a negative impact on the quality of life in affected individuals. It presents clinically as symmetric tan or brown patches on the face, most often involving the forehead, cheeks, perioral region, and periorbital region. On histologic examination, there is increased melanin in the epidermis and/or an increased number of melanosomes in the dermis, with a normal number of highly melanized and dendritic melanocytes. The mainstay of treatment is the use of sunscreen along with topical medications that suppress melanogenesis. Clearance is usually incomplete and recurrences or exacerbations are frequent, probably because of the poor efficacy in clearing dermal melanosomes. Treatment with high-energy pigment-specific lasers, ablative resurfacing lasers, and fractional lasers results in an unacceptably high rate of postinflammatory hyper- and hypopigmentation and rebound melasma. Recently, promising results have been achieved with low-fluence Q-switched neodymium-doped yttrium aluminium garnet laser treatment, which can selectively target dermal melanosomes without producing inflammation or epidermal damage, in all skin phototypes. This article reviews the current treatment modalities for melasma, the rationale for using and the clinical results of combination therapy with low-fluence Q-switched neodymium-doped yttrium aluminium garnet lasers.

  10. Automotive Aluminium Recycling

    Energy Technology Data Exchange (ETDEWEB)

    Gelas, B. des

    2000-07-01

    This paper aims at providing an overview on the contribution of aluminium recycling in the supply of new aluminium for automotive applications. Based on a presentation on how the global European automotive aluminium supply requirements are met, an analysis of the present and future contribution of automotive aluminium recycling is first presented. Current situation and future developments for automotive aluminium recycling practices are then commented, together with an outline on design principles for easier aluminium recycling. (orig.)

  11. Aluminium in human sweat.

    Science.gov (United States)

    Minshall, Clare; Nadal, Jodie; Exley, Christopher

    2014-01-01

    It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans.

  12. Aluminium structural elements

    OpenAIRE

    Švent, Nejc

    2016-01-01

    This thesis focuses on the structural analysis of aluminium structural members in accordance with the SIST EN 1999-1-1 standard. In the introduction, historical development of aluminium is summarized, as well as the processes of structural aluminium production and manufacture. Predominantly, resistance control checks of aluminium structural members are covered, with special attention to the major contrasts between aluminium and steel structural analyses. Finally, fundamental examples of resis...

  13. Does Aluminium Trigger Breast Cancer?

    Directory of Open Access Journals (Sweden)

    Peter Jennrich

    2016-08-01

    Full Text Available Summary. Breast cancer is by far the most common cancer in women in the western world. In 90% of breast cancers, environmental factors are among the causes. The frequency with which the tumour occurs in the outer upper part of the breast has risen with above average rates in recent decades. Aluminium salts as ingredients in deodorants and antiperspirants are being absorbed by the body to a greater extent than hitherto assumed. Their toxicity for healthy and diseased breast tissue cells includes various well-documented pathomechanisms. In the sense of primary and secondary prevention, the cancer-triggering potential of aluminium and its use in anti-perspirant deodorants must be re-evaluated. For the same reason the access to a targeted diagnosis and treatment of aluminium loading must be facilitated.

  14. Large-angle production of charged pions by 3 GeV/c - 12.9 GeV/c protons on beryllium, aluminium and lead targets

    CERN Document Server

    Catanesi, M G; Edgecock, R; Ellis, Malcolm; Soler, F J P; Gössling, C; Bunyatov, S; Krasnoperov, A; Popov, B; Serdiouk, V; Tereschenko, V; Di Capua, E; Vidal-Sitjes, G; Artamonov, A; Giani, S; Gilardoni, S; Gorbunov, P; Grant, A; Grossheim, A; Ivanchenko, V; Kayis-Topaksu, A; Panman, J; Papadopoulos, I; Chernyaev, E; Tsukerman, I; Veenhof, R; Wiebusch, C; Zucchelli, P; Blondel, A; Borghi, S; Morone, M C; Prior, G; Schroeter, R; Meurer, C; Gastaldi, U; Mills, G B; Graulich, J S; Grégoire, G; Bonesini, M; Ferri, F; Kirsanov, M; Bagulya, A; Grichine, V; Polukhina, N; Palladino, V; Coney, L; Schmitz, D; Barr, G; De Santo, A; Bobisut, F; Gibin, D; Guglielmi, A; Mezzetto, M; Dumarchez, J; Dore, U; Orestano, D; Pastore, F; Tonazzo, A; Tortora, L; Booth, C; Howlett, L; Bogomilov, M; Chizhov, M; Kolev, D; Tsenov, R; Piperov, Stefan; Temnikov, P; Apollonio, M; Chimenti, P; Giannini, G; Burguet-Castell, J; Cervera-Villanueva, A; Gómez-Cadenas, J J; Martín-Albo, J; Novella, P; Sorel, M; CERN. Geneva

    2008-01-01

    Measurements of the double-differential $\\pi^{\\pm}$ production cross-section in the range of momentum $100 \\MeVc \\leq p < 800 \\MeVc$ and angle $0.35 \\rad \\leq \\theta < 2.15 \\rad$ in proton--beryllium, proton--aluminium and proton--lead collisions are presented. The data were taken with the HARP detector in the T9 beam line of the CERN PS. The pions were produced by proton beams in a momentum range from 3 \\GeVc to 12.9 \\GeVc hitting a target with a thickness of 5% of a nuclear interaction length. The tracking and identification of the produced particles was performed using a small-radius cylindrical time projection chamber (TPC) placed inside a solenoidal magnet. Incident particles were identified by an elaborate system of beam detectors. Results are obtained for the double-differential cross-sections at six incident proton beam momenta (3 \\GeVc, 5 \\GeVc, 8 \\GeVc, 8.9 \\GeVc (Be only), 12 \\GeVc and 12.9 \\GeVc (Al only)) and compared to previously available data.

  15. Large-angle production of charged pions by 3-12.9 GeV/c protons on beryllium, aluminium and lead targets

    Energy Technology Data Exchange (ETDEWEB)

    Catanesi, M.G.; Radicioni, E. [Univ. degli Studi e Sezione INFN, Bari (Italy); Edgecock, R.; Ellis, M.; Soler, F.J.P. [Chilton, Rutherford Appleton Lab., Didcot (United Kingdom); Goessling, C. [Univ. Dortmund, Inst. fuer Physik, Dortmund (Germany); Bunyatov, S.; Krasnoperov, A.; Popov, B.; Serdiouk, V.; Tereschenko, V. [JINR Dubna, Joint Inst. for Nuclear Research, Dubna (Russian Federation); Di Capua, E.; Vidal-Sitjes, G. [Univ. degli Studi e Sezione INFN, Ferrara (Italy); Artamonov, A.; Giani, S.; Gilardoni, S.; Gorbunov, P.; Grant, A.; Grossheim, A.; Ivanchenko, A.; Ivanchenko, V.; Kayis-Topaksu, A.; Panman, J.; Papadopoulos, I.; Tcherniaev, E.; Tsukerman, I.; Veenhof, R.; Wiebusch, C.; Zucchelli, P. [CERN, Geneva (Switzerland); Blondel, A.; Borghi, S.; Morone, M.C.; Prior, G.; Schroeter, R. [Univ. de Geneve, Section de Physique, Geneve (Switzerland); Meurer, C. [Forschungszentrum Karlsruhe, Inst. fuer Physik, Karlsruhe (Germany); Gastaldi, U. [Lab. Nazionali di Legnaro dell' INFN, Legnaro (Italy); Mills, G.B. [Los Alamos National Lab., Los Alamos (United States); Graulich, J.S.; Gregoire, G. [UCL, Inst. de Physique Nucleaire, Louvain-la-Neuve (Belgium); Bonesini, M.; Ferri, F. [Univ. degli Studi e Sezione INFN Milano Bicocca, Milano (Italy); Kirsanov, M. [Inst. for Nuclear Research, Moscow (Russian Federation); Bagulya, A.; Grichine, V.; Polukhina, N. [Russian Academy of Sciences, P.N. Lebedev Inst. of Physics (FIAN), Moscow (Russian Federation); Palladino, V. [Univ. Federico II e Sezione INFN, Napoli (Italy); Coney, L.; Schmitz, D. [Columbia Univ., New York (United States); Barr, G.; De Santo, A. [Univ. of Oxford, Nuclear and Astrophysics Lab., Oxford (United Kingdom); Bobisut, F.; Gibin, D.; Guglielmi, A.; Mezzetto, M. [Univ. degli Studi e Sezione INFN, Padova (Italy); Dumarchez, J. [Univ. de Paris VI et VII, LPNHE, Paris (France); Dore, U. [Univ. La Sapienza e Sezione INFN Roma I, Roma (Italy)] [and others

    2008-03-15

    Measurements of the double-differential {pi}{sup {+-}} production cross-section in the range of momentum 100 MeV/c{<=}p< 800 MeV/c and angle 0.35 rad{<=}{theta}<2.15 rad in proton-beryllium, proton-aluminium and proton-lead collisions are presented. The data were taken with the HARP detector in the T9 beam line of the CERN PS. The pions were produced by proton beams in a momentum range from 3 GeV/c to 12.9 GeV/c hitting a target with a thickness of 5% of a nuclear interaction length. The tracking and identification of the produced particles was performed using a small-radius cylindrical time projection chamber (TPC) placed inside a solenoidal magnet. Incident particles were identified by an elaborate system of beam detectors. Results are obtained for the double-differential cross-sections d{sup 2}{sigma}/dpd{theta} at six incident proton beam momenta (3 GeV/c, 5 GeV/c, 8 GeV/c, 8.9 GeV/c (Be only), 12 GeV/c and 12.9 GeV/c (Al only)) and compared to previously available data. (orig.)

  16. A preliminary study of the dermal absorption of aluminium from antiperspirants using aluminium-26.

    Science.gov (United States)

    Flarend, R; Bin, T; Elmore, D; Hem, S L

    2001-02-01

    Aluminium chlorohydrate (ACH), the active ingredient in many antiperspirants, was labeled with the radioisotope 26Al. The labeled ACH was then fractionated into about 100 samples using gel filtration chromatography. Each fraction was analyzed for 26Al and total aluminium content. Aluminium-26 was only detected in the fractions that also contained aluminium, which verified that the ACH was uniformly labeled. 84 mg of the labeled ACH was then applied to a single underarm of two adult subjects with blood and urine samples being collected over 7 weeks. Tape-stripping and mild washings of the skin were also collected for the first 6 days. Results indicate that only 0.012% of the applied aluminium was absorbed through the skin. At this rate, about 4 microg of aluminium is absorbed from a single use of ACH on both underarms. This is about 2.5% of the aluminium typically absorbed by the gut from food over the same time period. Therefore, a one-time use of ACH applied to the skin is not a significant contribution to the body burden of aluminium.

  17. A 25m{sup 2} target-aligned heliostat with closed-loop control

    Energy Technology Data Exchange (ETDEWEB)

    Roos, Thomas; Ndumiso, Zwane; Kruger, Eu' odia [Council for Scientific and Industrial Research (CSIR), Pretoria (South Africa); Cathro, Robert [Denel Saab Aerostructures, Kempton Park (South Africa); Perumal, Strinivasan [Univ. of KwaZulu-Natal, Durban (South Africa). Dept. of Electronic Engineering

    2008-07-01

    A 25m{sup 2} target-aligned research heliostat with closed-loop control, with a theoretical concentration of 80 suns, has been built at CSIR in South Africa. The heliostat has four degrees of freedom: Azimuth, Elevation, Rotation and Pitch. A control system making use of a solar tracker has been developed and tested on a 1.25m{sup 2} target-aligned miniheliostat. A tracking accuracy of 3.3 milliradians was obtained. A good focal spot has been obtained with the 25m{sup 2} target-aligned research heliostat. (orig.)

  18. Sustainable Aluminium Systems

    Directory of Open Access Journals (Sweden)

    Sergio R. Ermolli

    2010-09-01

    Full Text Available In the present paper, an analytical presentation of some popular aluminium systems that contribute to sustainability of structures is presented. Special emphasis has been given to the properties of aluminium, while the influence of these systems in the overall performance of the structure regarding environment and economy is described. In particular, characteristics of aluminium elements such as high reflectivity and recyclability and their role in life cycle analysis (LCA are analyzed. The connections between energy efficiency and conservation of buildings and aluminium application are also discussed. Building applications such as curtain walls, window frames and facade sheets are presented and thoroughly investigated, considering their environmental and economic aspects. Furthermore, many innovative techniques that use aluminium elements in collaboration with other systems in order to produce renewable energy, such as solar panels and photovoltaics, are introduced. Finally, environmental innovations such as optimized ventilation mechanisms and light and shade management systems based on aluminium members are presented.

  19. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    OpenAIRE

    B. Formanek; J. Piątkowski; J. Szymszal

    2010-01-01

    Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameter...

  20. MiR-25 protects cardiomyocytes against oxidative damage by targeting the mitochondrial calcium uniporter.

    Science.gov (United States)

    Pan, Lei; Huang, Bi-Jun; Ma, Xiu-E; Wang, Shi-Yi; Feng, Jing; Lv, Fei; Liu, Yuan; Liu, Yi; Li, Chang-Ming; Liang, Dan-Dan; Li, Jun; Xu, Liang; Chen, Yi-Han

    2015-03-10

    MicroRNAs (miRNAs) are a class of small non-coding RNAs, whose expression levels vary in different cell types and tissues. Emerging evidence indicates that tissue-specific and -enriched miRNAs are closely associated with cellular development and stress responses in their tissues. MiR-25 has been documented to be abundant in cardiomyocytes, but its function in the heart remains unknown. Here, we report that miR-25 can protect cardiomyocytes against oxidative damage by down-regulating mitochondrial calcium uniporter (MCU). MiR-25 was markedly elevated in response to oxidative stimulation in cardiomyocytes. Further overexpression of miR-25 protected cardiomyocytes against oxidative damage by inactivating the mitochondrial apoptosis pathway. MCU was identified as a potential target of miR-25 by bioinformatical analysis. MCU mRNA level was reversely correlated with miR-25 under the exposure of H2O2, and MCU protein level was largely decreased by miR-25 overexpression. The luciferase reporter assay confirmed that miR-25 bound directly to the 3' untranslated region (UTR) of MCU mRNA. MiR-25 significantly decreased H2O2-induced elevation of mitochondrial Ca2+ concentration, which is likely to be the result of decreased activity of MCU. We conclude that miR-25 targets MCU to protect cardiomyocytes against oxidative damages. This finding provides novel insights into the involvement of miRNAs in oxidative stress in cardiomyocytes.

  1. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.;

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

  2. Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.;

    1968-01-01

    Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produces...... rows of dislocation loops all lying parallel to one particular direction. If the aluminium target is quenched from 600 °C and annealed at room temperature prior to irradiation with aluminium ions, the rows of loops are suppressed. The amount of damage observed is considerably less than would...

  3. Recovery in aluminium

    DEFF Research Database (Denmark)

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

  4. A 2.5m long liquid hydrogen target for COMPASS

    CERN Document Server

    Bielert, E; Doshita, N; Geyer, R; Hashimoto, R; Horikawa, N; Ishimoto, S; Iwata, T; Kondo, K; Mallot, G K; Matsuda, H; Matsuda, T; Miyachi, Y; Nukazuka, G; Pirotte, O; Suzuki, H; Suzuki, S; Vullierme, B

    2014-01-01

    A 2.5 m long liquid hydrogen target has been developed for the COMPASS experiment at CERN to investigate the nucleon spin structure via the Deeply Virtual Compton Scattering (DVCS) process. To recognize exclusive DVCS events, produced photons and slow protons need to be detected. In order to do so, the material budget around the target has to be minimal. A 0.125 mm thick Kapton s target cell and a 1 mm thick carbon fi ber vacuum chamber with a Mylar s window have been constructed and tested. Finally, the target system was successfully employed during the DVCS pilot run in COMPASS at the end of 2012. The objective of this paper is to give a detailed description of this newly developed liquid hydrogen target apparatus

  5. Aluminium removal from water after defluoridation with the electrocoagulation process.

    Science.gov (United States)

    Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

    2015-01-01

    Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

  6. Electrolytic deposition of aluminium-magnesium-alloys from electrolytes containing organo-aluminium complexes; Elektrolytische Abscheidung von Aluminium-Magnesium-Legierungen aus aluminiumorganischen Komplexelektrolyten

    Energy Technology Data Exchange (ETDEWEB)

    Lehmkuhl, H.; Mehler, K.; Bongard, H.; Tesche, B. [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany); Reinhold, B. [Audi AG, Ingolstadt (Germany). Technische Entwicklung

    2000-10-01

    The galvanic deposition of pure aluminium from fluoride-containing electrolytes has been developed further and for the first time aluminium and magnesium have been deposited from a toluene-solution of a halide-free organo-aluminium complex electrolyte. The rate of incorporation of magnesium can be controlled over a wide range by either adjusting the composition of the aluminium-magnesium anode or by using separate aluminium or magnesium anodic circuits. The current efficiency for both anode and cathode approaches 100%. The resulting coating is optically attractive and, depending upon the magnesium-content or the cathodic current density, can be formed as a dull or polished surface. Investigations using an electron microscope show that the surface, in contrast to that of pure aluminium, consists of spherical particles. The aluminium-magnesium coating provides excellent protection against the corrosion of magnesium components. Electrochemical investigations using, for example 25% by weight magnesium incorporation, indicate a pronounced passivity interval compared to the alloy AZ91hp. In contrast to galvanic zinc-plated and silicate-sealed examples, cyclic corrosion tests on screws simulating 10 years of exposure, show no corrosion. (orig.)

  7. Fatal aluminium phosphide poisoning

    Directory of Open Access Journals (Sweden)

    Meena Mahesh Chand

    2015-06-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

  8. NKX2-5 mutations causative for congenital heart disease retain functionality and are directed to hundreds of targets

    Science.gov (United States)

    Bouveret, Romaric; Waardenberg, Ashley J; Schonrock, Nicole; Ramialison, Mirana; Doan, Tram; de Jong, Danielle; Bondue, Antoine; Kaur, Gurpreet; Mohamed, Stephanie; Fonoudi, Hananeh; Chen, Chiann-mun; Wouters, Merridee A; Bhattacharya, Shoumo; Plachta, Nicolas; Dunwoodie, Sally L; Chapman, Gavin; Blanpain, Cédric; Harvey, Richard P

    2015-01-01

    We take a functional genomics approach to congenital heart disease mechanism. We used DamID to establish a robust set of target genes for NKX2-5 wild type and disease associated NKX2-5 mutations to model loss-of-function in gene regulatory networks. NKX2-5 mutants, including those with a crippled homeodomain, bound hundreds of targets including NKX2-5 wild type targets and a unique set of "off-targets", and retained partial functionality. NKXΔHD, which lacks the homeodomain completely, could heterodimerize with NKX2-5 wild type and its cofactors, including E26 transformation-specific (ETS) family members, through a tyrosine-rich homophilic interaction domain (YRD). Off-targets of NKX2-5 mutants, but not those of an NKX2-5 YRD mutant, showed overrepresentation of ETS binding sites and were occupied by ETS proteins, as determined by DamID. Analysis of kernel transcription factor and ETS targets show that ETS proteins are highly embedded within the cardiac gene regulatory network. Our study reveals binding and activities of NKX2-5 mutations on WT target and off-targets, guided by interactions with their normal cardiac and general cofactors, and suggest a novel type of gain-of-function in congenital heart disease. DOI: http://dx.doi.org/10.7554/eLife.06942.001 PMID:26146939

  9. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.H.H.; Soetens, F.

    2006-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical pr

  10. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    Directory of Open Access Journals (Sweden)

    B. Formanek

    2010-10-01

    Full Text Available Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameters. The methods of light and scanning microscopy were used to reveal the structure of composite casting. Changes in chemical composition and phase composition of particles of the FeAl intermetallic phase in aluminium matrix were confirmed. The structure of silumin casting with matrix containing microregions of ceramic and intermetallic phases, typical of hybrid reinforcements, was obtained.

  11. Crystal Structure of the Human NKX2.5 Homeodomain in Complex with DNA Target

    Energy Technology Data Exchange (ETDEWEB)

    Pradhan, Lagnajeet; Genis, Caroli; Scone, Peyton; Weinberg, Ellen O.; Kasahara, Hideko; Nam, Hyun-Joo (BU-M); (Florida); (Texas)

    2012-10-16

    NKX2.5 is a homeodomain containing transcription factor regulating cardiac formation and function, and its mutations are linked to congenital heart disease. Here we provide the first report of the crystal structure of the NKX2.5 homeodomain in complex with double-stranded DNA of its endogenous target, locating within the proximal promoter -242 site of the atrial natriuretic factor gene. The crystal structure, determined at 1.8 {angstrom} resolution, demonstrates that NKX2.5 homeodomains occupy both DNA binding sites separated by five nucleotides without physical interaction between themselves. The two homeodomains show identical conformation despite the differences in the DNA sequences they bind, and no significant bending of the DNA was observed. Tyr54, absolutely conserved in NK2 family proteins, mediates sequence-specific interaction with the TAAG motif. This high resolution crystal structure of NKX2.5 protein provides a detailed picture of protein and DNA interactions, which allows us to predict DNA binding of mutants identified in human patients.

  12. Recovery in aluminium

    OpenAIRE

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X-ray diffraction technique for studies of the evolution of grains within polycrystalline materials. The much smaller volume of the crystallites of interest here in comparison to grains implies that the ...

  13. Laser welding of aluminium alloys

    OpenAIRE

    Forsman, Tomas

    2000-01-01

    This thesis treats laser welding of aluminium alloys from a practical perspective with elements of mathematical analysis. The theoretical work has in all cases been verified experimentally. The aluminium alloys studied are from the 5xxx and 6xxx groups which are common for example in the automotive industry. Aluminium has many unique physical properties. The properties which more than others have been shown to influence the welding process is its high reflection, high thermal conductivity, lo...

  14. Method of aluminium fluoride manufacture

    International Nuclear Information System (INIS)

    The manufacture of aluminium fluoride is based on waste processing in uranium hexafluoride conversion to uranium oxides within the fuel cycle. The conversion is the stoichiometric conversion of uranium hexafluoride with aluminium nitrate to uranyl nitrate. This is extracted from the water phase by phosphoric acid trialkyl ester to an organic solvent and further processed. The discharge water phase is solidified by evaporation to solid aluminium fluoride and nitric acid. (M.S.)

  15. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

  16. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity. PMID:27025067

  17. Void formation in pure aluminium irradiated with high-energetic electron beams and gamma-quanta

    DEFF Research Database (Denmark)

    Gan, V. V.; Ozhigou, L. S.; Yamnitsky, V. A.;

    1983-01-01

    The spatial distribution of displaced atoms and helium atoms and also the spectra of damaging energies of primary displaced atoms in a thick aluminium target irradiated with electrons of 225 MeV energy were calculated. Pure aluminium (99.9999%) irradiated up to 0.04 dose was studied by electron...

  18. First Principles Study of Aluminium Vacancy in Wurtzite Aluminium Nitride

    Institute of Scientific and Technical Information of China (English)

    GAO Ting-Ge; YI Jue-Min; ZHOU Zi-Yao; HU Xiao-Dong

    2008-01-01

    @@ We report that the aluminium vacancy in wurtzite AIN brings about two impurity levels e and a2 in the band gap, not just one single t2 level The aluminium vacancy carries a magnetic moment of 1 μB in the ground state. The molecule orbit of the aluminium vacancy becomes e↑↑ a2↑ rather than e↑↑ a2↑. The calculation is carried out by using the CASTEP code. The intrinsic symmetry of wurtzite A1N is the driving force for this spin splitting. Finally the symmetry of wurtzite AlN results in an anti-ferromagnetic coupling between the aluminium vacancies, as is predicted. Our findings are helpful to gain a more through understanding of the structural and spin property of aluminium vacancy in wurtzite AIN.

  19. Domestic Output of Aluminium Alloy Hub Surpassing 70 million in 2007

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>According to a report from the hub branch of China Association of Automobile Manufactur- ers,China has produced a total of more than 70 million aluminium alloy hubs in 2007,a year- on-year growth over 25%,while consuming over 700,000 tons of primary aluminium the whole year.

  20. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  1. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2005-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge load

  2. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge load

  3. Rabphilin-3A, a putative target protein for smg p25A/rab3A p25 small GTP-binding protein related to synaptotagmin.

    OpenAIRE

    Shirataki, H; Kaibuchi, K; Sakoda, T.; Kishida, S; Yamaguchi, T.; Wada, K.; Miyazaki, M.; Takai, Y.

    1993-01-01

    In a previous study (H. Shirataki, K. Kaibuchi, T. Yamaguchi, K. Wada, H. Horiuchi, and Y. Takai, J. Biol. Chem. 267:10946-10949, 1992), we highly purified from bovine brain crude membranes the putative target protein for smg p25A/rab3A p25, a ras p21-related small GTP-binding protein implicated in neurotransmitter release. In this study, we have isolated and sequenced the cDNA of this protein from a bovine brain cDNA library. The cDNA had an open reading frame encoding a protein of 704 amino...

  4. Roll bonding of strained aluminium

    DEFF Research Database (Denmark)

    Staun, Jakob M.

    2003-01-01

    This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right circumsta......This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... circumstances both materials show good bonding, but the high purity material is excluded because of recrystallisation and the resulting loss of mechanical properties. The effect of cross stacking and roll bonding pre-strained sheets of the commercial purity material is investigated and some dependence...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

  5. Aluminium, antiperspirants and breast cancer.

    Science.gov (United States)

    Darbre, P D

    2005-09-01

    Aluminium salts are used as the active antiperspirant agent in underarm cosmetics, but the effects of widespread, long term and increasing use remain unknown, especially in relation to the breast, which is a local area of application. Clinical studies showing a disproportionately high incidence of breast cancer in the upper outer quadrant of the breast together with reports of genomic instability in outer quadrants of the breast provide supporting evidence for a role for locally applied cosmetic chemicals in the development of breast cancer. Aluminium is known to have a genotoxic profile, capable of causing both DNA alterations and epigenetic effects, and this would be consistent with a potential role in breast cancer if such effects occurred in breast cells. Oestrogen is a well established influence in breast cancer and its action, dependent on intracellular receptors which function as ligand-activated zinc finger transcription factors, suggests one possible point of interference from aluminium. Results reported here demonstrate that aluminium in the form of aluminium chloride or aluminium chlorhydrate can interfere with the function of oestrogen receptors of MCF7 human breast cancer cells both in terms of ligand binding and in terms of oestrogen-regulated reporter gene expression. This adds aluminium to the increasing list of metals capable of interfering with oestrogen action and termed metalloestrogens. Further studies are now needed to identify the molecular basis of this action, the longer term effects of aluminium exposure and whether aluminium can cause aberrations to other signalling pathways in breast cells. Given the wide exposure of the human population to antiperspirants, it will be important to establish dermal absorption in the local area of the breast and whether long term low level absorption could play a role in the increasing incidence of breast cancer. PMID:16045991

  6. Separation of 35S-sulfate on neutral aluminium oxide

    International Nuclear Information System (INIS)

    The results of 35S-sulfate chromatography on neutral aluminium oxide (γ-Al2O3) are presented. Possibility of quantitative adsorption of 35S-sulfate on Al2O3 from acidic or neutral potassium chloride solutions of high concentration is shown. Dynamic adsorption capacity of neutral aluminium oxide with respect to sulfate from weakly acidic potassium chloride solution equals near 10 μmol/ml of adsorbent. Optimal parameters for chromatographic isolation of 35S-sulfate without carrier from irradiated KCl target are determined. (author)

  7. Friction surfacing of aluminium alloys

    OpenAIRE

    Pereira, Diogo Jorge O. A.

    2012-01-01

    Friction surfacing is a solid state joining process that has attracted much interest in the past decades. This technology allows joining dissimilar metallic materials while avoiding the brittle intermetallic formations, involving temperatures bellow melting point and producing like forged metal structures. Much research using different steels has been made but the same does not happen with aluminium alloys, specially using different aluminium alloys. Friction surface coatings using cons...

  8. Constitutive modelling of aluminium alloy sheet at warm forming temperatures

    Science.gov (United States)

    Kurukuri, S.; Worswick, M. J.; Winkler, S.

    2016-08-01

    The formability of aluminium alloy sheet can be greatly improved by warm forming. However predicting constitutive behaviour under warm forming conditions is a challenge for aluminium alloys due to strong, coupled temperature- and rate-sensitivity. In this work, uniaxial tensile characterization of 0.5 mm thick fully annealed aluminium alloy brazing sheet, widely used in the fabrication of automotive heat exchanger components, is performed at various temperatures (25 to 250 °C) and strain rates (0.002 and 0.02 s-1). In order to capture the observed rate- and temperature-dependent work hardening behaviour, a phenomenological extended-Nadai model and the physically based (i) Bergstrom and (ii) Nes models are considered and compared. It is demonstrated that the Nes model is able to accurately describe the flow stress of AA3003 sheet at different temperatures, strain rates and instantaneous strain rate jumps.

  9. Pressureless sintered silicon carbide tailored with aluminium nitride sintering agent

    International Nuclear Information System (INIS)

    This study reports the influence of aluminium nitride on the pressureless sintering of cubic phase silicon carbide nanoparticles (β-SiC). Pressureless sintering was achieved at 2000 degrees C for 5 min with the additions of boron carbide together with carbon of 1 wt% and 6 wt%, respectively, and a content of aluminium nitride between 0 and 10 wt%. Sintered samples present relative densities higher than 92%. The sintered microstructure was found to be greatly modified by the introduction of aluminium nitride, which reflects the influence of nitrogen on the β-SiC to α-SiC transformation. The toughness of sintered sample was not modified by AlN incorporation and is relatively low (around 2.5 MPa m1/2). Materials exhibited transgranular fracture mode, indicating a strong bonding between SiC grains. (authors)

  10. Low-temperature Electrodeposition of Aluminium from Lewis Acidic 1-Allyl-3-methylimidazolium Chloroaluminate Ionic Liquids

    Institute of Scientific and Technical Information of China (English)

    郑勇; 张锁江; 吕兴梅; 王倩; 左勇; 刘恋

    2012-01-01

    Lewis acidic 1-allyl-3-methylimidazolium chloroaluminate ionic liquids were used as promising electrolytes in the low-temperature electrodeposition of aluminium. Systematic studies on deposition process have been performed by cYClic voltammetry and chronoamperometry. The surface morphology and X-ray diffraction (XRD) patterns of deposits prepared at different experimental conditions were also investigated. It was shown that the nucleation density and growth rate of crystallites had a great effect on the structure of aluminium deposited. The crys- tallographic orientation of deposits was mainly influenced by temperature and current density. Smooth, dense and well adherent aluminium coatings were obtained on copper substrates at 10-25 mA.cm^-2 and 313.2-353.2 K. More- over, the current efficiency of deposition and purity of aluminium have been significantly improved, demonstrating that the ionic liquids tested have a prospectful potential in electroplating and electrorefining of aluminium.

  11. Saturation effect in projectile- and target- x-ray production in collisions between 2.5 MeV/u highly charged Cu ions and gaseous targets

    Science.gov (United States)

    Kumar, Ajay; Misra, D.; Kelkar, A. H.; Kadhane, U.; Singh, Y. P.; Lapicki, G.; Gulyas, L.; Tribedi, L. C.

    2006-01-01

    L x-ray production cross sections have been measured for highly charged 2.5 MeV/u Cuq+ (q = 20-26) ions colliding with H2, Ne, Ar, Kr and Xe target atoms. The observed Cu L x-rays are due to the excitation and electron-transfer processes. The charge state dependence of the projectile L x-rays has been studied with Ar and Kr targets. We have derived the subshell resolved K-L1, K-L2 and K-L3 electron-transfer cross sections from the measured Ar K x-ray yields as a function of L vacancies in Cu ion. The measured projectile L x-ray production cross sections arising from the excitation and electron capture are found to saturate as target atomic number Zt increases. Similarly, a saturation has also been found in the Ar K-shell ionization cross sections as a function of Zp.

  12. Therapeutic Targeting the Cell Division Cycle 25 (CDC25 Phosphatases in Human Acute Myeloid Leukemia — The Possibility to Target Several Kinases through Inhibition of the Various CDC25 Isoforms

    Directory of Open Access Journals (Sweden)

    Annette K. Brenner

    2014-11-01

    Full Text Available The cell division cycle 25 (CDC25 phosphatases include CDC25A, CDC25B and CDC25C. These three molecules are important regulators of several steps in the cell cycle, including the activation of various cyclin-dependent kinases (CDKs. CDC25s seem to have a role in the development of several human malignancies, including acute myeloid leukemia (AML; and CDC25 inhibition is therefore considered as a possible anticancer strategy. Firstly, upregulation of CDC25A can enhance cell proliferation and the expression seems to be controlled through PI3K-Akt-mTOR signaling, a pathway possibly mediating chemoresistance in human AML. Loss of CDC25A is also important for the cell cycle arrest caused by differentiation induction of malignant hematopoietic cells. Secondly, high CDC25B expression is associated with resistance against the antiproliferative effect of PI3K-Akt-mTOR inhibitors in primary human AML cells, and inhibition of this isoform seems to reduce AML cell line proliferation through effects on NFκB and p300. Finally, CDC25C seems important for the phenotype of AML cells at least for a subset of patients. Many of the identified CDC25 inhibitors show cross-reactivity among the three CDC25 isoforms. Thus, by using such cross-reactive inhibitors it may become possible to inhibit several molecular events in the regulation of cell cycle progression and even cytoplasmic signaling, including activation of several CDKs, through the use of a single drug. Such combined strategies will probably be an advantage in human cancer treatment.

  13. X-ray back-lighter characterization for iron opacity measurements using laser-produced aluminium K-alpha emission

    OpenAIRE

    Rossall, A K; Gartside, L. M. R.; Chaurasia, S.; Tripathi, S; Munda, D. S.; Gupta, N K; Dhareshwar, L. J.; Gaffney, J; Rose, S. J.; Tallents, G J; , Tel

    2010-01-01

    Abstract Aluminium K ? emission (1.5 keV) produced by an 8 J, 500 ps, Nd:Glass laser incident at 45? onto a layered target of 0.8 ?m thick aluminium (front side) and 1?m thick iron (back side) has been used to probe the opacity of iron plasma. Source broadened spectroscopy and continuum emission analysis shows that whole beam self focussing within the aluminium plasma results in a two temperature spatial distribution. Thermal conduction from the laser-irradiated aluminium into the iron lay...

  14. Dispersion strengthening of aluminium-aluminium-oxide products

    DEFF Research Database (Denmark)

    Hansen, Niels

    1970-01-01

    temperature and at 400°C is in agreement with Orowan's theory. The increase in flow stress at room temperature for strain values below 3 per cent was related to the plastic strain by the equation σ-σoy=k1ε 1/2, where σoy is the initial flow stress and where k1 increases for increasing volume fraction......The true stress-true strain curves at room temperature and at 400°C were determined for various types of aluminium-aluminium-oxide products containing from 0.2 to 4.7 weight per cent of aluminium oxide. The effect of particles on the initial flow stress and the flow stress for 0.2% offset at room...

  15. Preparation of aluminium lakes by electrocoagulation

    OpenAIRE

    Prapai Pradabkham

    2008-01-01

    Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  16. Effect of hydrogen on aluminium and aluminium alloys: A review

    DEFF Research Database (Denmark)

    Ambat, Rajan; Dwarakadasa, E.S.

    1996-01-01

    Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

  17. Quasielastic Scattering of the Halo Nucleus 6He at 25 MeV/u from a 9Be Target

    Institute of Scientific and Technical Information of China (English)

    PANG Dan-Yang; ZHANG Gao-Long; HU Qing-Yuan; WANG Jia; A.Ozawa; Y.Yamaguchi; R.Kanungo; D.Fang; I.Tanihata; YE Yan-Lin; JIANG Dong-Xing; ZHENG Tao; WANG Quan-Jin; LI Zhi-Huan; LI Xiang-Qing; GE Yu-Cheng; WU Cui-E

    2004-01-01

    @@ The differential cross sections of quasielastic scattering of a 25 MeV/u 6He from 9Be target have been measured.The double-folding model approach is applied to generate the real part of the optical potential The imaginary potential parameters as well as some of the real potential parameters are studied in comparison with the experimental data. The effect of the unstable nucleus is discussed.

  18. Buckwheat stomatal traits under aluminium toxicity

    Directory of Open Access Journals (Sweden)

    Oleksandr E. Smirnov

    2014-04-01

    Full Text Available Aluminium influence on some stomatal parameters of common buckwheat (Fagopyrum esculentum Moench. was studied. Significant changes in stomatal density, stomatal index and stomatal shape coefficient under aluminium treatment were revealed. Stomatal closure and no difference in total stomatal potential conductance index of treatment plants were suggested as aluminium resistance characteristics.

  19. Gene Regulatory Scenarios of Primary 1,25-Dihydroxyvitamin D3 Target Genes in a Human Myeloid Leukemia Cell Line

    Directory of Open Access Journals (Sweden)

    Moray J. Campbell

    2013-10-01

    Full Text Available Genome- and transcriptome-wide data has significantly increased the amount of available information about primary 1,25-dihydroxyvitamin D3 (1,25(OH2D3 target genes in cancer cell models, such as human THP-1 myelomonocytic leukemia cells. In this study, we investigated the genes G0S2, CDKN1A and MYC as master examples of primary vitamin D receptor (VDR targets being involved in the control of cellular proliferation. The chromosomal domains of G0S2 and CDKN1A are 140–170 kb in size and contain one and three VDR binding sites, respectively. This is rather compact compared to the MYC locus that is 15 times larger and accommodates four VDR binding sites. All eight VDR binding sites were studied by chromatin immunoprecipitation in THP-1 cells. Interestingly, the site closest to the transcription start site of the down-regulated MYC gene showed 1,25(OH2D3-dependent reduction of VDR binding and is not associated with open chromatin. Four of the other seven VDR binding regions contain a typical DR3-type VDR binding sequence, three of which are also occupied with VDR in macrophage-like cells. In conclusion, the three examples suggest that each VDR target gene has an individual regulatory scenario. However, some general components of these scenarios may be useful for the development of new therapy regimens.

  20. Impact of Inert Metal Particles Flow on Aluminium Plate

    Institute of Scientific and Technical Information of China (English)

    WANG Zhongqi; LIU Yi; CHEN Yahong; BAI Chunhua

    2008-01-01

    Inert metal explosive, a new kind of explosive, is a mixture of high explosive and inert metal particle.When this kind of explosive is detonated, an inert metal particle flow will be formed by the explosive product driving.To determine the characteristics of the movement of the metal particle flow, a series of aluminium plates were designed to be the targets on which the metal particle flow impacted.The test result was presented and a numerical model was set up to analyze the impact of the high speed inert metal particles on aluminium plate.Based on the numerical analysis, the relationship between the characteristic of the mark on the target plate and the initial condition of the inert metal particles was proposed.From the analysis of the impact on target plates, more information about the movement of the metal particles could be reconstructed.

  1. Association of impulsivity and polymorphic microRNA-641 target sites in the SNAP-25 gene.

    Directory of Open Access Journals (Sweden)

    Nóra Németh

    Full Text Available Impulsivity is a personality trait of high impact and is connected with several types of maladaptive behavior and psychiatric diseases, such as attention deficit hyperactivity disorder, alcohol and drug abuse, as well as pathological gambling and mood disorders. Polymorphic variants of the SNAP-25 gene emerged as putative genetic components of impulsivity, as SNAP-25 protein plays an important role in the central nervous system, and its SNPs are associated with several psychiatric disorders. In this study we aimed to investigate if polymorphisms in the regulatory regions of the SNAP-25 gene are in association with normal variability of impulsivity. Genotypes and haplotypes of two polymorphisms in the promoter (rs6077690 and rs6039769 and two SNPs in the 3' UTR (rs3746544 and rs1051312 of the SNAP-25 gene were determined in a healthy Hungarian population (N = 901 using PCR-RFLP or real-time PCR in combination with sequence specific probes. Significant association was found between the T-T 3' UTR haplotype and impulsivity, whereas no association could be detected with genotypes or haplotypes of the promoter loci. According to sequence alignment, the polymorphisms in the 3' UTR of the gene alter the binding site of microRNA-641, which was analyzed by luciferase reporter system. It was observed that haplotypes altering one or two nucleotides in the binding site of the seed region of microRNA-641 significantly increased the amount of generated protein in vitro. These findings support the role of polymorphic SNAP-25 variants both at psychogenetic and molecular biological levels.

  2. High-speed deposition of protective films of aluminium oxide by the method of reactive magnetron sputtering

    International Nuclear Information System (INIS)

    The high optical characteristics of aluminium films made them attractive for different functional and decorative applications. It is well-known that the corrosion resistance of alloying is determined by the presence of the oxide film on its surface, but on the aluminium films, deposited by vacuum methods, the resistance is extremely low resulting in the relatively rapid failure of the coating. At present, there is a large number of methods of depositing the films of aluminium oxide. In most cases, it is recommended to use reactive magnetron sputtering of an aluminium target in a magnetron spraying system (MSS) using direct current, on dispersion of the target of aluminium oxide in a high-frequency MSS

  3. The prophylactic reduction of aluminium intake.

    Science.gov (United States)

    Lione, A

    1983-02-01

    The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail. PMID:6337934

  4. Electrochemical properties and thermal stability of epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    ZORICA M. KACAREVIC-POPOVIC

    2001-12-01

    Full Text Available The corrosion behaviour of epoxy coatings electrodeposited on aluminium, as well as on electrochemically and chemically modified aluminium were investigated during exposure to 3 % NaCl. Electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA were used for the determination of the protective properties of epoxy coatings on aluminium, anodized aluminium, phosphatized and chromatized-phosphatized aluminium. The protective properties of epoxy coatings on anodized and chromatized-phosphatized aluminium are significantly improved with respect to the same epoxy coatings on aluminium and phosphatized aluminium: higher values of the pore resitance and charge-transfer resistance, lower values of the coating capacitance, double-layer capacitance and relative permittivity (from EIS smaller amount of absorbed water inside the coating (From TGA. On the other hand, the lower values of the ipdt temperature indicate a lower thermal stability of the epoxy coatings on anodized and chromatized-phosphatized aluminium.

  5. Recovery mechanisms in nanostructured aluminium

    DEFF Research Database (Denmark)

    Yu, Tianbo; Hansen, Niels; Huang, Xiaoxu

    2012-01-01

    Commercial purity aluminium (99.5%) has been cold rolled to a true strain of 5.5 (99.6% reduction in thickness). The material is very strong but low temperature recovery may be a limiting factor. This has been investigated by isothermal annealing treatments in the temperature range 5–100C. Hardness...

  6. Constitutive modelling of aluminium foams

    NARCIS (Netherlands)

    Wang, W.M.; Lemmen, P.P.M.

    2001-01-01

    In this paper an aluminium foam model is proposed for a vehicle crash analysis. The model assumes that there is no coupling between stresses and strains in different principal directions. The stress in each principle direction is then interpolated from an experimental recorded uniaxial stress strain

  7. Microchemistry in aluminium sheet production

    NARCIS (Netherlands)

    Lok, Z.J.

    2005-01-01

    The production of aluminium sheet alloys from as-cast ingots is a complex process, involving several rolling operations in combination with various thermal heat treatments. Through their influence on the alloy microchemistry and microstructure, these thermomechanical treatments are all aimed at cont

  8. Factors affecting the aluminium content of human femoral head and neck.

    Science.gov (United States)

    Zioła-Frankowska, Anetta; Dąbrowski, Mikołaj; Kubaszewski, Łukasz; Rogala, Piotr; Frankowski, Marcin

    2015-11-01

    Tissues for the study were obtained intraoperatively during hip replacement procedures from 96 patients. In all the cases, the indication for this treatment was primary or secondary degenerative changes in the hip joint. The subject of the study was the head and neck of the femur, resected in situ. Aluminium concentrations measured in femoral head and neck samples from patients aged between 25 and 91 were varied. Statistical methods were applied to determine the variations in relation to the parameters from the background survey. Significant differences in the aluminium content of femoral head samples were observed between patients under and over 60 years of age. Based on the results, it was confirmed that the aluminium accumulates in bones over a lifetime. The study showed that the content of aluminium in the head and neck of the femur depends on the factors such as: type of medicines taken, contact with chemicals at work, differences in body anatomy and sex. The study on the levels of aluminium in bones and the factors affecting its concentration is a valuable source of information for further research on the role of aluminium in bone diseases. Based on the investigations, it was found that the GF-AAS technique is the best analytical tool for routine analysis of aluminium in complex matrix samples. The use of femoral heads in the investigations was approved by the Bioethics Committee of the University of Medical Sciences in Poznań (Poland).

  9. Enhanced Proton Beam Focusing due to Proximal Target Structures on the 1.25 kJ OMEGA EP Laser

    Science.gov (United States)

    McGuffey, Chris; Kim, J.; Qiao, B.; Beg, F. N.; Wei, M. S.; Fitzsimmons, P.; Evans, M.; Stephens, R. B.; Fuchs, J.; Chen, S. N.; Nilson, P. M.; Canning, D.; Mastrosimone, D.; Foord, M. E.; McLean, H. S.

    2013-10-01

    Understanding how to generate and control laser-driven proton beams has shown significant progress in the last 15 years. However, to exploit promising applications, practical aspects must be addressed, such as the effect of structures holding the target and dynamics when the beam enters any sample. Using the 1.25 kJ, 10 ps OMEGA EP BL laser and spherically curved C targets we studied the spot size of a high-density proton beam directed at a Cu foil using three target mounting configurations: 1 on a stalk, 2 with an open-sided wedge structure on the back, and 3 with a conical structure. The brightness of Cu Kα fluorescence from the center of the foil was weakest from the stalk-mounted target, 5x brighter with the wedge, and 8x brighter with the cone, indicating enhanced focusing due to the structures. Plasma features and fields from the interaction were temporally and spatially resolved using proton radiography from a separate broad-spectrum proton beam (0-40 MeV) driven by OMEGA EP SL. We also discuss a follow-on experiment that will study transport of the proton beam through various materials. This work was supported by the DOE/NNSA NLUF program, Grant DE-NA0002034.

  10. Combinatorial targeting of TSLP, IL-25, and IL-33 in type 2 cytokine-driven inflammation and fibrosis.

    Science.gov (United States)

    Vannella, Kevin M; Ramalingam, Thirumalai R; Borthwick, Lee A; Barron, Luke; Hart, Kevin M; Thompson, Robert W; Kindrachuk, Kristen N; Cheever, Allen W; White, Sandra; Budelsky, Alison L; Comeau, Michael R; Smith, Dirk E; Wynn, Thomas A

    2016-05-01

    Thymic stromal lymphopoietin (TSLP), interleukin-25 (IL-25), and IL-33 are important initiators of type 2-associated mucosal inflammation and immunity. However, their role in the maintenance of progressive type 2 inflammation and fibrosis is much less clear. Using chronic models of helminth infection and allergic lung inflammation, we show that collective disruption of TSLP, IL-25, and IL-33 signaling suppresses chronic and progressive type 2 cytokine-driven inflammation and fibrosis. In a schistosome lung granuloma model or during chronic Schistosoma mansoni infection in the liver, individual ablation of TSLP, IL-25, or IL-33/ST2 had no impact on the development of IL-4/IL-13-dependent inflammation or fibrosis. However, significant reductions in granuloma-associated eosinophils, hepatic fibrosis, and IL-13-producing type 2 innate lymphoid cells (ILC2s) were observed when signaling of all three mediators was simultaneously disrupted. Combined blockade through monoclonal antibody (mAb) treatment also reduced IL-5 and IL-13 expression during primary and secondary granuloma formation in the lungs. In a model of chronic house dust mite-induced allergic lung inflammation, combined mAb treatment did not decrease established inflammation or fibrosis. TSLP/IL-33 double-knockout mice treated with anti-IL-25 mAb during priming, however, displayed decreased inflammation, mucus production, and lung remodeling in the chronic phase. Together, these studies reveal partially redundant roles for TSLP, IL-25, and IL-33 in the maintenance of type 2 pathology and suggest that in some settings, early combined targeting of these mediators is necessary to ameliorate progressive type 2-driven disease. PMID:27147589

  11. Bumblebee pupae contain high levels of aluminium.

    Science.gov (United States)

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  12. Friction Welding of Aluminium and Aluminium Alloys with Steel

    Directory of Open Access Journals (Sweden)

    Andrzej Ambroziak

    2014-01-01

    Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

  13. Metal doped fluorocarbon polymer films prepared by plasma polymerization using an RF planar magnetron target

    Science.gov (United States)

    Biederman, H.; Holland, L.

    1983-07-01

    Fluorocarbon films have been prepared by plasma polymerization of CF4 using an RF planar magnetron with an aluminium target. More than one order of magnitude higher deposition rate has been achieved in comparison with an r.f. diode system operated under similar conditions of monomer pressure and flow rate and power input. A glow discharge in a CF4[25%]-argon [75%] mixture was used to incorporate aluminium from a target electrode into the polymer films. The foregoing mixture and another based on CF4 [87%]-argon [13%] were used in the RF discharge with a copper target. Some experiments with a gold target and pure CF4 as the inlet gas were also made. The film structure was examined by SEM and TEM and characteristic micrographs are presented here. The composition of the films was estimated from an AES study. The sheet resistivity of the metal/polymer film complexes was determined.

  14. Role of Root Exudates in Adaptative Reactions of Buckwheat Plants in Aluminium-acid Stress

    Directory of Open Access Journals (Sweden)

    A.E. Smirnov

    2014-03-01

    Full Text Available Aliminium toxicity is major limiting factor of crop production in acidic soils. It is known that mechanisms of toxic effects of aluminium are differing in biochemical characters, research of aluminium toxicity complicated by variety of its chemical forms and migration in soil and water ability. The root exudates qualitative composition of common buckwheat was evaluated. Organic complexing agents – oxalic acid and phenolic compounds were revealed. The role of these complexing agents in the buckwheat aluminium resistance under acidic stress, participation in processes of external and internal detoxification was shown. Spectrophometric assay revealed an increase in root secretion of oxalic acid by 2.5 times and decrease in content of phenolic compounds in root exudates solution by 3 times upon aluminium (50 µM treatment. In the meanwhile the same concentration of the metal had induced phenylalanine ammonia-lyase activity by 2 times.

  15. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

  16. Aluminium in Allergies and Allergen immunotherapy.

    Science.gov (United States)

    Jensen-Jarolim, Erika

    2015-01-01

    Aluminium is a hot topic in the current debate. Exposure occurs due to environmental, dietary and intentional exposure to aluminium, such as in vaccines where it was introduced in 1926. In spite of the fact that it is a typical Th2 adjuvant, aluminium redirects the immune response in systemic allergen immunotherapy (SIT) upon prolonged immunization. SIT in the US, and SLIT in general, are at present non-adjuvanted therapies, but in Europe aluminium is used as adjuvant in most SIT preparations. It enhances the safety of SIT by local deposition of the allergen. Undesired properties of aluminium adjuvants comprise acute and chronic inflammation at the injection site, its Th2 immune stimulatory capacity, its accumulation besides biodistribution in the body. The adjuvant and safety profile of aluminium adjuvants in allergy vaccines are discussed, as well as the need for putting modern delivery systems and adjuvants on the fast track.

  17. Dietary aluminium Intake Level for Rent Animals in a Primary and Secondary Aluminium Industry Surrounding Area

    OpenAIRE

    Mărioara Drugă; Alexandru Trif; Mihai Drugă; Ducu Ştef; Ştefan Munteanu

    2010-01-01

    The study was carried out in an aluminium industry surrounding area on purpose to evaluate dietary aluminium intake level for rent animals originated from fodder and water consumed by them. There were taken feed and water samples in different periods and from increasing distances from industrial platform, determined the aluminium level by atomic spectroscopy and calculated the rations for cattle and poultry. Conclusions: aluminium dietary intake level by ration depends by forage period for st...

  18. Does Aluminium Trigger Breast Cancer?

    OpenAIRE

    Peter Jennrich; Claus Schulte-Uebbing

    2016-01-01

    Summary. Breast cancer is by far the most common cancer in women in the western world. In 90% of breast cancers, environmental factors are among the causes. The frequency with which the tumour occurs in the outer upper part of the breast has risen with above average rates in recent decades. Aluminium salts as ingredients in deodorants and antiperspirants are being absorbed by the body to a greater extent than hitherto assumed. Their toxicity for healthy and diseased breast tissue cells includ...

  19. A biogeochemical cycle for aluminium?

    Science.gov (United States)

    Exley, Christopher

    2003-09-15

    The elaboration of biogeochemical cycles for elements which are known to be essential for life has enabled a broad appreciation of the homeostatic mechanisms which underlie element essentiality. In particular they can be used effectively to identify any part played by human activities in element cycling and to predict how such activities might impact upon the lithospheric and biospheric availability of an element in the future. The same criteria were the driving force behind the construction of a biogeochemical cycle for aluminium, a non-essential element which is a known ecotoxicant and a suspected health risk in humans. The purpose of this exercise was to examine the concept of a biogeochemical cycle for aluminium and not to review the biogeochemistry of this element. The cycle as presented is rudimentary and qualitative though, even in this nascent form, it is informative and predictive and, for these reasons alone, it is deserving of future quantification. A fully fledged biogeochemical cycle for aluminium should explain the biospheric abundance of this element and whether we should expect its (continued) active involvement in biochemical evolution.

  20. A bakable aluminium vacuum chamber with an aluminium flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the construction of the vacuum chamber in proton synchrotrons and electron storage rings. (author)

  1. Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

    Energy Technology Data Exchange (ETDEWEB)

    Moe, J. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

  2. Aluminium in foodstuffs and diets in Sweden.

    Science.gov (United States)

    Jorhem, L; Haegglund, G

    1992-01-01

    The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources. PMID:1542992

  3. CD69 is a TGF-β/1α,25-dihydroxyvitamin D3 target gene in monocytes.

    Directory of Open Access Journals (Sweden)

    Thea K Wöbke

    Full Text Available CD69 is a transmembrane lectin that can be expressed on most hematopoietic cells. In monocytes, it has been functionally linked to the 5-lipoxygenase pathway in which the leukotrienes, a class of highly potent inflammatory mediators, are produced. However, regarding CD69 gene expression and its regulatory mechanisms in monocytes, only scarce data are available. Here, we report that CD69 mRNA expression, analogous to that of 5-lipoxygenase, is induced by the physiologic stimuli transforming growth factor-β (TGF-β and 1α,25-dihydroxyvitamin D3 (1α,25(OH2D3 in monocytic cells. Comparison with T- and B-cell lines showed that the effect was specific for monocytes. CD69 expression levels were increased in a concentration-dependent manner, and kinetic analysis revealed a rapid onset of mRNA expression, indicating that CD69 is a primary TGF-β/1α,25(OH2D3 target gene. PCR analysis of different regions of the CD69 mRNA revealed that de novo transcription was initiated and proximal and distal parts were induced concomitantly. In common with 5-lipoxygenase, no activation of 0.7 kb or ∼2.3 kb promoter fragments by TGF-β and 1α,25(OH2D3 could be observed in transient reporter assays for CD69. Analysis of mRNA stability using a transcription inhibitor and a 3'UTR reporter construct showed that TGF-β and 1α,25(OH2D3 do not influence CD69 mRNA stability. Functional knockdown of Smad3 clearly demonstrated that upregulation of CD69 mRNA, in contrast to 5-LO, depends on Smad3. Comparative studies with different inhibitors for mitogen activated protein kinases (MAPKs revealed that MAPK signalling is involved in CD69 gene regulation, whereas 5-lipoxygenase gene expression was only partly affected. Mechanistically, we found evidence that CD69 gene upregulation depends on TAK1-mediated p38 activation. In summary, our data indicate that CD69 gene expression, conforming with 5-lipoxygenase, is regulated monocyte-specifically by the physiologic stimuli TGF

  4. Study and Elimination of the Interference of Aluminium on the Voltammetric Determination of Uranium with Chloranilic Acid. Application to the Determination of Uranium in Waters and Geological Samples

    International Nuclear Information System (INIS)

    The interference of aluminium during the voltammetric determination of uranium with 2,5-dichloro-3,6-dihydroxy-1,4-benzoquinone (chloranilic acid) has been investigated. The presence of aluminium originates a voltammetric signal due to its chloranilic acid complex at the same potential range as the uranium analytical signal appears. The interference of aluminium can be overcome by addition of an appropriate amount of sodium fluoride as complexing reagent. The determination of uranium by adsorptive stripping voltammetry (AdSV) can be carried out at concentration levels as low as 1 μg/L in the presence of 100 μg/L aluminium after the addition of 100μL of 0.1 mol/L NaF. The method can be applied to the determination of uranium in aluminium-containing waters and geological samples containing high aluminium levels. (Author) 19 refs

  5. Aluminium exclusion and aluminium tolerance in woody plants

    OpenAIRE

    Ivano eBrunner; Christoph eSperisen

    2013-01-01

    The aluminium (Al) cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion...

  6. Revised Stellar Properties of Kepler Targets for the Q1-17 (DR25) Transit Detection Run

    CERN Document Server

    Mathur, Savita; Batalha, Natalie M; Ciardi, David R; Bastien, Fabienne A; Bieryla, Allyson; Buchhave, Lars A; Cochran, William D; Endl, Michael; Esquerdo, Gilbert A; Furlan, Elise; Howard, Andrew W; Howell, Steve B; Isaacson, Howard; Latham, David W; MacQueen, Phillip J; Silva, David R

    2016-01-01

    The determination of exoplanet properties and occurrence rates using Kepler data critically depends on our knowledge of the fundamental properties (such as temperature, radius and mass) of the observed stars. We present revised stellar properties for 197,096 Kepler targets observed between Quarters 1-17 (Q1-17), which were used for the final transiting planet search run by the Kepler Mission (Data Release 25, DR25). Similar to the Q1--16 catalog by Huber et al. the classifications are based on conditioning published atmospheric parameters on a grid of Dartmouth isochrones, with significant improvements in the adopted methodology and over 29,000 new sources for temperatures, surface gravities or metallicities. In addition to fundamental stellar properties the new catalog also includes distances and extinctions, and we provide posterior samples for each stellar parameter of each star. Typical uncertainties are ~27% in radius, ~17% in mass, and ~51% in density, which is somewhat smaller than previous catalogs du...

  7. Preparation of aluminium lakes by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Prapai Pradabkham

    2008-07-01

    Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  8. Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

    Science.gov (United States)

    Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

    2016-02-01

    Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

  9. Acoustic properties of aluminium foams

    Directory of Open Access Journals (Sweden)

    García, L. E.

    2008-09-01

    Full Text Available The article discusses normal incidence sound absorption by aluminium foam manufactured with powder metallurgy technology. Aluminium foams with different surface morphologies were obtained by varying the type of precursor and adding filler materials during the foaming process. The sound absorption coefficients found for these aluminium foams were compared to the coefficient for commercial foams marketed under the name ALPORAS. The effect of foam thickness on the absorption coefficient was studied for each sample prepared. The combination of good acoustic and mechanical properties makes aluminium foams particularly attractive products. The study included an analysis of the effect of 2-, 5- and 10-cm air gaps on the sound absorption coefficient. The results showed that such gaps, which are routinely used in construction to reduce the reverberation period in indoor premises, raised the low frequency absorption coefficient significantly. This increase was found to depend on aluminium foam density and thickness and the depth of the air gap. In this same line, we have investigated the absorption coefficient of the aluminium foams combined with a mineral fiber panel.Se presenta un estudio del coeficiente de absorción acústica a incidencia normal de espumas de aluminio fabricadas mediante la técnica pulvimetalúrgica. Se fabricaron espumas de aluminio de distinta morfología superficial variando el tipo de precursor y usando materiales de relleno durante el proceso de espumación. Se muestra un estudio comparativo del coeficiente de absorción acústica de las espumas de aluminio fabricadas y las espumas comerciales conocidas como ALPORAS. Para cada muestra fabricada se estudió la influencia del espesor sobre el valor del coeficiente de absorción.El atractivo de las espumas de aluminio radica en que en ellas se combinan interesantes propiedades acústicas y mecánicas. Se analizó el efecto de una cámara de aire de 2, 5 y 10 cm de anchura sobre el

  10. Control of Microthrix parvicella by aluminium salts addition.

    Science.gov (United States)

    Durban, N; Juzan, L; Krier, J; Gillot, S

    2016-01-01

    Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella.

  11. Targeted re-sequencing analysis of 25 genes commonly mutated in myeloid disorders in del(5q) myelodysplastic syndromes

    Science.gov (United States)

    Fernandez-Mercado, Marta; Burns, Adam; Pellagatti, Andrea; Giagounidis, Aristoteles; Germing, Ulrich; Agirre, Xabier; Prosper, Felipe; Aul, Carlo; Killick, Sally; Wainscoat, James S.; Schuh, Anna; Boultwood, Jacqueline

    2013-01-01

    Interstitial deletion of chromosome 5q is the most common chromosomal abnormality in myelodysplastic syndromes. The catalogue of genes involved in the molecular pathogenesis of myelodysplastic syndromes is rapidly expanding and next-generation sequencing technology allows detection of these mutations at great depth. Here we describe the design, validation and application of a targeted next-generation sequencing approach to simultaneously screen 25 genes mutated in myeloid malignancies. We used this method alongside single nucleotide polymorphism-array technology to characterize the mutational and cytogenetic profile of 43 cases of early or advanced del(5q) myelodysplastic syndromes. A total of 29 mutations were detected in our cohort. Overall, 45% of early and 66.7% of advanced cases had at least one mutation. Genes with the highest mutation frequency among advanced cases were TP53 and ASXL1 (25% of patients each). These showed a lower mutation frequency in cases of 5q- syndrome (4.5% and 13.6%, respectively), suggesting a role in disease progression in del(5q) myelodysplastic syndromes. Fifty-two percent of mutations identified were in genes involved in epigenetic regulation (ASXL1, TET2, DNMT3A and JAK2). Six mutations had allele frequencies <20%, likely below the detection limit of traditional sequencing methods. Genomic array data showed that cases of advanced del(5q) myelodysplastic syndrome had a complex background of cytogenetic aberrations, often encompassing genes involved in myeloid disorders. Our study is the first to investigate the molecular pathogenesis of early and advanced del(5q) myelodysplastic syndromes using next-generation sequencing technology on a large panel of genes frequently mutated in myeloid malignancies, further illuminating the molecular landscape of del(5q) myelodysplastic syndromes. PMID:23831921

  12. A Reaction Coating on Aluminium Alloys by Laser Processing

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1993-01-01

    An aluminium oxide layer of 100 µm in thickness has been successfully coated on aluminium alloy 6061 and pure aluminium using a powder mixture of silicon oxide and aluminium by laser processing. A strong Al/Al2O3 interface was formed. The exothermic chemical reaction between SiO2 and Al may promote

  13. Shot peening of aluminium alloys

    International Nuclear Information System (INIS)

    Shot peening is a process of cold-hammering where a metallic surface is pelted with spherical grains. Each grain bumping into the surface acts as a hammer head and creates a small crater. The overlapping of these craters produces a residual compression layer just underneath the surface. It is well known that cracks cannot spread in a compression zone. In most cases of fatigue rupture and stress corrosion cracks propagate from the surface towards the inside so shot peening allows a longer lifetime of castings. Moreover most materials present a better resistance due to the cold-hammering effect of shot peening. Metallic surfaces can be treated in workshops or directly on site. Typical pieces that undergo shot peening on site are storing tanks, gas and steam turbines, tubes of steam generators and piping in oil or nuclear or chemical industries. This article describes shot peening from a theoretical and general point of view and presents the application to aluminium-lithium alloys. In the case of aluminium alloys shot peening can be used to shape the piece (peen-forming). (A.C.)

  14. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  15. Refractory oxides containing aluminium and barium

    OpenAIRE

    Davies T.J.; Biedermann M.; Q-G. Chen; Emblem H. G.; Al-Douri W. A.

    1998-01-01

    Oxides containing aluminium and barium, optionally with chromium, are refractory with several possible industrial uses. A gel precursor of an oxide having the formula BaO.n(Al2xCr2yO3), where 1aluminium salt or a solution of an aluminium salt and a chromium III salt, then forming a gel which was fired to obtain the desired oxide. Filaments may be drawn as the gel is forming or extr...

  16. Dietary aluminium Intake Level for Rent Animals in a Primary and Secondary Aluminium Industry Surrounding Area

    Directory of Open Access Journals (Sweden)

    Mărioara Drugă

    2010-05-01

    Full Text Available The study was carried out in an aluminium industry surrounding area on purpose to evaluate dietary aluminium intake level for rent animals originated from fodder and water consumed by them. There were taken feed and water samples in different periods and from increasing distances from industrial platform, determined the aluminium level by atomic spectroscopy and calculated the rations for cattle and poultry. Conclusions: aluminium dietary intake level by ration depends by forage period for studied species, rations structure and distance from industrial platform and didn’t reach toxic level in any case.

  17. Aluminium induced oxidative stress results in decreased mitochondrial biogenesis via modulation of PGC-1α expression.

    Science.gov (United States)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Kandimalla, Ramesh J L; Bal, Amanjit; Gill, Kiran Dip

    2013-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the effects of aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of Peroxisome proliferator activated receptor gamma co-activator 1α (PGC-1α) and its downstream targets i.e. Nuclear respiratory factor-1(NRF-1), Nuclear respiratory factor-2(NRF-2) and Mitochondrial transcription factor A (Tfam) in mitochondrial biogenesis. Aluminium lactate (10mg/kgb.wt./day) was administered intragastrically to rats for 12 weeks. After 12 weeks of exposure, we found an increase in ROS levels, mitochondrial DNA oxidation and decrease in citrate synthase activity in the Hippocampus (HC) and Corpus striatum (CS) regions of rat brain. On the other hand, there was a decrease in the mRNA levels of the mitochondrial encoded subunits-NADH dehydrogenase (ND) subunits i.e. ND1, ND2, ND3, Cytochrome b (Cytb), Cytochrome oxidase (COX) subunits i.e. COX1, COX3, ATP synthase (ATPase) subunit 6 along with reduced expression of nuclear encoded subunits COX4, COX5A, COX5B of Electron transport chain (ETC). Besides, a decrease in mitochondrial DNA copy number and mitochondrial content in both regions of rat brain was observed. The PGC-1α was down-regulated in aluminium treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α in aluminium treated rats. Electron microscopy results revealed a significant increase in the mitochondrial swelling, loss of cristae, chromatin condensation and decreases in mitochondrial number in case of aluminium treated rats as compared to control. So, PGC-1α seems to be a potent target for aluminium neurotoxicity, which makes it an almost ideal target to control or limit the damage that has been associated with the defective mitochondrial function seen in neurodegenerative diseases.

  18. Spectrum Simulation of Li-Like Aluminium Plasma

    Institute of Scientific and Technical Information of China (English)

    PENG Feng; JIANG Gang; ZHU Zheng-He

    2006-01-01

    X-ray emission spectra for L-shell of Li-like aluminium ions are simulated by using the flexible atomic code based on the collisional radiative model. Atomic processes including radiative recombination, dielectronic recombination, collisional ionization and resonance excitation from the neighbouring ion (Al9+ and Al11+) charge states of the target ion (Al10+) are considered in the model. In addition, the contributions of different atomic processes to the x-ray spectrum are analysed. The results show that dielectronic recombination, radiative recombination, collisional ionization and resonance excitation, other than direct collisional excitation, are very important processes.

  19. Release Behaviour of Shock Loaded LY12 Aluminium Alloy

    Institute of Scientific and Technical Information of China (English)

    YAN Min; DAI Lan-Hong; SHEN Le-Tian

    2005-01-01

    @@ By making use of a light gas gun, a specially designed target is impacted by the LY12 flyer, and the pressure is taken in the range of 0.6-3 GPa. Based on the stress profiles measured in the buffer materials by manganese gauges, the Hugoniot curve and release curves of LY12 aluminium alloy are obtained. Meanwhile, the release curves from different initial shocked states are described in both the pressure-particle velocity plane and the pressure-specific volume plane.

  20. Aluminium Process Fault Detection and Diagnosis

    Directory of Open Access Journals (Sweden)

    Nazatul Aini Abd Majid

    2015-01-01

    Full Text Available The challenges in developing a fault detection and diagnosis system for industrial applications are not inconsiderable, particularly complex materials processing operations such as aluminium smelting. However, the organizing into groups of the various fault detection and diagnostic systems of the aluminium smelting process can assist in the identification of the key elements of an effective monitoring system. This paper reviews aluminium process fault detection and diagnosis systems and proposes a taxonomy that includes four key elements: knowledge, techniques, usage frequency, and results presentation. Each element is explained together with examples of existing systems. A fault detection and diagnosis system developed based on the proposed taxonomy is demonstrated using aluminium smelting data. A potential new strategy for improving fault diagnosis is discussed based on the ability of the new technology, augmented reality, to augment operators’ view of an industrial plant, so that it permits a situation-oriented action in real working environments.

  1. Deformation features of aluminium in tensile tests

    International Nuclear Information System (INIS)

    It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 4000C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.)

  2. Steam Initiated Surface Modification of Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud

    , crystalline nano-particles, role of steam-based treatment on adhesion of industrially applied powder coating, and investigations of a failed painted aluminium window profile due to defects in the extruded profile. Chapters 13 and 14 describe the overall discussion, conclusions and future work based......The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco...

  3. Steam generated conversion coating on aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    and growth of oxide film on different intermetallic particles and corrosion behaviour of such alloys.Surface morphology was observed by using FEG-SEM, EDX and FIB-SEM. Metal oxide surface characterization and compositional depth profiling were investigated by using XPS and GD-OES respectively......Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed......) depending on the preparation parameters/conditions. Moreover, with the knowledge of factors controlling film growth, composition and morphology, such oxide layers carry huge potential for practical applications. Pure aluminium (AA1090, 99.94 wt. %) and other aluminium alloy surfaces were exposed to high...

  4. Shear Viscosity of Aluminium under Shock Compression

    Institute of Scientific and Technical Information of China (English)

    LIU Fu-Sheng; YANG Mei-Xia; LIU Qi-Wen; CHEN Jun-Xiang; JING Fu-Qian

    2005-01-01

    @@ Based on the Newtonian viscous fluid model and the analytic perturbation theory of Miller and Ahrens for the oscillatory damping of a sinusoidal shock front, a flyer-impact technique is developed to investigate the effecti veviscosity of shocked aluminium.

  5. Increasing world demand for primary aluminium in the current decade: An encumbrance for environment? - A partial equilibrium analysis

    Energy Technology Data Exchange (ETDEWEB)

    Poganietz, W.R. [Forschungszentrum Juelich (Germany). Systemforschung und Technologische Entwicklung

    2001-07-01

    Aluminium is in the manufacturing and consumer industry a very popular light metal. The prevalence of aluminium is due to its mineralogical and chemical characteristics. The objective of the paper is to discuss, whether an increase in worldwide demand for primary aluminium is a growing burden for environment. Primary aluminium processing is by its nature energy and resource intensive and thus, potentially, high polluting. The paper focuses on emissions of carbon dioxide and the per fluorocarbons (PFCs) CF4 and C2H6. The analysis is made by using the model GlobAl, a partial equilibrium world aluminium trade model. It depicts the material flow of primary aluminium processing. Estimating rising demand for primary aluminium, reaching in 2010 25m t, 28m t and 31m t, resp, compared to 20m t in 1995, production of bauxite, alumina, and primary aluminium will increase. Growing production requires rising energy input in the material flow. However, declining specific energy consumption offsets only in low demand scenario this trend completely. Total emissions of considered greenhouse gases, which are influenced by energy use, would fall in two of three scenarios. Only in case of high demand, additional production of primary aluminium and thus extra emissions are not offset by the drastic decline of specific emissions. The drop of specific emissions is mainly due to a decline of PFCs gaseous emissions, which occur only in electrolysis. Looking at smelters as main issuer of CO2, the drop of specific emissions in all three cases is mainly due to higher efficiency of power generation and energy use in the smelting process. Irrespective of that, the emission level of CO2 during electrolyse will reach in 2010 nearly the lowest possible one using the currently known state of the art technology as a reference point. This will not be the case regarding PFCs emissions.

  6. Recycling of AlMgSi1 aluminium chips by cold compression

    OpenAIRE

    T. Pepelnjak; K. Kuzman; Kačmarčik, I.; Plančak, M.

    2012-01-01

    Current work elaborates possibilities for direct conversion of AlMgSi1 aluminium chips into solid billets by solid state recycling. Milling chips from an aluminium alloy were cold compressed in a closed cylindrical die by means of a 2,5 MN hydraulic press. Due to low initial relative density of the chips, several pre-compressions were needed. In order to establish the infl uence of chip geometry on the final density of billets different types of chips were cut by using various milling regimes...

  7. Bone marrow aluminium storage in renal failure.

    OpenAIRE

    Kaye, M.

    1983-01-01

    Using the staining method for aluminium with the ammonium salt of aurine tricarboxylic acid, aluminon, 18 patients with end stage renal disease gave positive reactions in iliac crest bone biopsies and 11 of these had positive staining in the bone marrow. In one the marrow was positive and the bone negative. The marrow reaction is putatively regarded as caused by aluminium storage in unidentified cells, possibly of the macrophage system which are strongly fluorescent when examined after prior ...

  8. DETERMINATION OF IMPURITY ELEMENTS IN ALUMINIUM

    Institute of Scientific and Technical Information of China (English)

    侯小琳; 张永保

    1994-01-01

    Twenty five impurity elements in aluminium applied as reactor material are determined.Titanium and nickel are determined with epithermal neutron activation analysis(NAA),magnesium and silicon by inductance coupling plasma emission spectra(ICP),other elements by thermal NAA.The fission coefficient of uranium is given by an experiment,the interferences of uranium to Ce,Nd,Mo,Zr,La,Sm are subtracted.The detection limits of these methods to all of impurity elements in aluminium are calculated.

  9. Silane based coating of aluminium mold

    DEFF Research Database (Denmark)

    2013-01-01

    having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...... of structures which would otherwise be difficult to mold. The resistance of the coated aluminium mold is significantly improved by applying a silane-based coating layer....

  10. Electrical Conductivity of Aluminium Alloy Foams

    Institute of Scientific and Technical Information of China (English)

    凤仪; 郑海务; 朱震刚; 祖方遒

    2002-01-01

    Closed-cell aluminium alloy foams were produced using the powder metallurgical technique. The effect of porosityand cell diameter on the electrical conductivity of foams was investigated and the results were compared with anumber of models. It was found that the percolation theory can be successfully applied to describe the dependenceof the electrical conductivity of aluminium alloy foams on the relative density. The cell diameter has a negligibleeffect on the electrical conductivity of foams.

  11. Ongoing characterization of passivated aluminium nanopowders

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, Q.S.M.; Fouchard, R.C.; Turcotte, A-M.; Abdel-Qader, Z.; Jones, D.E.G. [Natural Resources Canada, CANMET, Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2002-04-01

    For characterization, the thermal behaviour of two aluminium nanopowders - Alss and Alssef - in air was determined using differential scanning calorimetry (DSC), simultaneous thermogravimetry-DTA (TG-DTA) and accelerating rate calorimetry (ARC). Alss and Alssef were found to be less reactive to air than previously determined for Als And Alex, possibly due to their thicker and different type of passivating layer. Stability determination for Alss and Alssef in a wet oxidizing environment was carried out using ARC, whereas outgassing behaviour of mixtures of ammonium dinitramide (ADN) and the various aluminium powders was investigated using TG-DTA-FTIR-MS (Fourier Transform Infrared Spectrometry-Mass Spectrometry). The addition of various aluminium powders resulted in only minimal effect on the thermal stability of ADN. Electrostatic discharge, friction sensitivities of ADN and its mixtures with various aluminium powders, and thermal stability and sensitivity of mixtures of nano-sized molybdenum trioxide with aluminium nanopowders were also studied. The electrostatic discharge sensitivity of molybdenum trioxide was shown to increase by the addition of aluminium nanopowders. 23 refs., 5 tabs., 7 figs.

  12. Thermoluminescent response of aluminium oxide thin films subject to gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Arrieta, A.; Escobar A, L.; Camps, E.; Villagran, E.; Gonzalez, P.R

    2006-07-01

    The thermoluminescent (TL) properties of amorphous aluminium oxide thin films (thicknesses as low as 0.3 {mu}m) subjected to gamma (Co-60) irradiation are reported. Aluminium oxide thin films were prepared by laser ablation from an Al{sub 2}O{sub 3} target using a Nd: YAG laser with emission at the fundamental line. The films were exposed to gamma radiation (Co-60) in order to study their TL response. Thermoluminescence glow curves exhibited two peaks at 110 and 176 C. The high temperature peak shows good stability and 30% fading in the first 5 days after irradiation. A linear relationship between absorbed dose and the thermoluminescent response for doses span from 150 mGy to 100 Gy was observed. These results suggest that aluminium oxide thin films are suitable for detection and monitoring of gamma radiation. (Author)

  13. Recycling of AlMgSi1 aluminium chips by cold compression

    Directory of Open Access Journals (Sweden)

    T. Pepelnjak

    2012-10-01

    Full Text Available Current work elaborates possibilities for direct conversion of AlMgSi1 aluminium chips into solid billets by solid state recycling. Milling chips from an aluminium alloy were cold compressed in a closed cylindrical die by means of a 2,5 MN hydraulic press. Due to low initial relative density of the chips, several pre-compressions were needed. In order to establish the infl uence of chip geometry on the final density of billets different types of chips were cut by using various milling regimes. The infl uence of a compression regime due to various chip types were followed by load–stroke diagrams. Up to 97 % of density measured at extruded aluminium was attained for one type of chips. Results show that the shapes of the chips and their size (especially thickness have a considerable infl uence on the final integrity of billets.

  14. CDC25A Protein Stability Represents a Previously Unrecognized Target of HER2 Signaling in Human Breast Cancer: Implication for a Potential Clinical Relevance in Trastuzumab Treatment

    Directory of Open Access Journals (Sweden)

    Emanuela Brunetto

    2013-06-01

    Full Text Available The CDC25A-CDK2 pathway has been proposed as critical for the oncogenic action of human epidermal growth factor receptor 2 (HER2 in mammary epithelial cells. In particular, transgenic expression of CDC25A cooperates with HER2 in promoting mammary tumors, whereas CDC25A hemizygous loss attenuates the HER2-induced tumorigenesis penetrance. On the basis of this evidence of a synergism between HER2 and the cell cycle regulator CDC25A in a mouse model of mammary tumorigenesis, we investigated the role of CDC25A in human HER2-positive breast cancer and its possible implications in therapeutic response. HER2 status and CDC25A expression were assessed in 313 breast cancer patients and we found statistically significant correlation between HER2 and CDC25A (P = .007. Moreover, an HER2-positive breast cancer subgroup with high levels of CDC25A and very aggressive phenotype was identified (P = .005. Importantly, our in vitro studies on breast cancer cell lines showed that the HER2 inhibitor efficacy on cell growth and viability relied also on CDC25A expression and that such inhibition induces CDC25A down-regulation through phosphatidylinositol 3-kinase/protein kinase B pathway and DNA damage response activation. In line with this observation, we found a statistical significant association between CDC25A overexpression and trastuzumab-combined therapy response rate in two different HER2-positive cohorts of trastuzumab-treated patients in either metastatic or neoadjuvant setting (P = .018 for the metastatic cohort and P = .021 for the neoadjuvant cohort. Our findings highlight a link between HER2 and CDC25A that positively modulates HER2- targeted therapy response, suggesting that, in HER2-positive breast cancer patients, CDC25A overexpression affects trastuzumab sensitivity.

  15. Quasi-elastic Scattering of a Secondary 6He Beam on a 9Be Target at 25MeV/Nucleon

    Institute of Scientific and Technical Information of China (English)

    陈陶; 叶沿林; 李智焕; 江栋兴; 华辉; 李湘庆; 王全进; 葛榆成; 庞丹阳; 狄振宇; 靳根明; 肖国青; 郭忠言; 肖志刚; 王宏伟; 张保国; 吴和宇; 李家兴; 孙志宇; 詹文龙

    2002-01-01

    The quasi-elastic scattering of a secondary 6He beam (25 MeV/n) on a 9Be target has been measured for the firsttime with the application of a sophisticated tracking detector system. The angular distribution is reported. Aphenomenological optical potential is obtained by fitting the experimental data, which encourages more accurateexperimental measurements.

  16. Targeting of Slc25a21 is associated with orofacial defects and otitis media due to disrupted expression of a neighbouring gene.

    Directory of Open Access Journals (Sweden)

    Simon Maguire

    Full Text Available Homozygosity for Slc25a21(tm1a(KOMPWtsi results in mice exhibiting orofacial abnormalities, alterations in carpal and rugae structures, hearing impairment and inflammation in the middle ear. In humans it has been hypothesised that the 2-oxoadipate mitochondrial carrier coded by SLC25A21 may be involved in the disease 2-oxoadipate acidaemia. Unexpectedly, no 2-oxoadipate acidaemia-like symptoms were observed in animals homozygous for Slc25a21(tm1a(KOMPWtsi despite confirmation that this allele reduces Slc25a21 expression by 71.3%. To study the complete knockout, an allelic series was generated using the loxP and FRT sites typical of a Knockout Mouse Project allele. After removal of the critical exon and neomycin selection cassette, Slc25a21 knockout mice homozygous for the Slc25a21(tm1b(KOMPWtsi and Slc25a21(tm1d(KOMPWtsi alleles were phenotypically indistinguishable from wild-type. This led us to explore the genomic environment of Slc25a21 and to discover that expression of Pax9, located 3' of the target gene, was reduced in homozygous Slc25a21(tm1a(KOMPWtsi mice. We hypothesize that the presence of the selection cassette is the cause of the down regulation of Pax9 observed. The phenotypes we observed in homozygous Slc25a21(tm1a(KOMPWtsi mice were broadly consistent with a hypomorphic Pax9 allele with the exception of otitis media and hearing impairment which may be a novel consequence of Pax9 down regulation. We explore the ramifications associated with this particular targeted mutation and emphasise the need to interpret phenotypes taking into consideration all potential underlying genetic mechanisms.

  17. Let-7a modulates particulate matter (≤ 2.5 μm)-induced oxidative stress and injury in human airway epithelial cells by targeting arginase 2.

    Science.gov (United States)

    Song, Lei; Li, Dan; Gu, Yue; Li, Xiaoping; Peng, Liping

    2016-10-01

    Epidemiological studies show that particulate matter (PM) with an aerodynamic diameter ≤ 2.5 μm (PM2.5) is associated with cardiorespiratory diseases via the induction of excessive oxidative stress. However, the precise mechanism underlying PM2.5-mediated oxidative stress injury has not been fully elucidated. Accumulating evidence has indicated the microRNA let-7 family might play a role in PM-mediated pathological processes. In this study, we investigated the role of let-7a in oxidative stress and cell injury in human bronchial epithelial BEAS2B (B2B) cells after PM2.5 exposure. The let-7a level was the most significantly decreased in B2B cells after PM2.5 exposure. The overexpression of let-7a suppressed intracellular reactive oxygen species levels and the percentage of apoptotic cells after PM2.5 exposure, while the let-7a level decreased arginase 2 (ARG2) mRNA and protein levels in B2B cells by directly targeting the ARG2 3'-untranslated region. ARG2 expression was upregulated in B2B cells during PM2.5 treatment, and ARG2 knockdown could remarkably reduce oxidative stress and cellular injury. Moreover, its restoration could abrogate the protective effects of let-7a against PM2.5-induced injury. In conclusion, let-7a decreases and ARG2 increases resulting from PM2.5 exposure may exacerbate oxidative stress, cell injury and apoptosis of B2B cells. The let-7a/ARG2 axis is a likely therapeutic target for PM2.5-induced airway epithelial injury. Copyright © 2016 John Wiley & Sons, Ltd. PMID:26989813

  18. Heat treatment of aluminium strip coils; Gluehbehandlung von Aluminium-Bandbunden

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, Dominik; Dambauer, Georg [LOI Thermprocess GmbH, Essen (Germany)

    2012-08-15

    Nowadays, aluminium strip coils are increasingly heat-treated in single-coil lifting hearth furnaces SCL. Flexible, individual heat treatment allows fast reactions to short term requirements for the production of aluminium strip and offers energy saving possibilities. The following report describes the advantages of single-coil hearth furnaces in terms of flexibility, energy consumption and possible configurations. (orig.)

  19. Design of welded aluminium connections (Entwurf und Berechnung von Aluminium Schweissverbindungen)

    NARCIS (Netherlands)

    Soetens, F.

    1998-01-01

    In the past two decades considerable research effort has been put into welded aluminium connections in order to better understand their structural behaviour and to up-date the design rules in the existing standards at the time [1]. Since weids in aluminium are more critical compared to steel, the ab

  20. Aluminium exclusion and aluminium tolerance in woody plants

    Directory of Open Access Journals (Sweden)

    Ivano eBrunner

    2013-06-01

    Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

  1. Aluminium as heating fuel. Tests with aluminium powder prove suitability in principle. Aluminium als Heizungs-Brennstoff. Versuche mit Aluminiumpulver beweisen prinzipielle Eignung

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R.

    1990-12-01

    Tests prove that aluminium powder is perfectly suited as fuel and storage material for solar energy. The combustion product itself is again the base material for aluminium production, i.e. aluminium can be recycled. There are three problematic areas: 1. flame stability, 2. combustion duration and 3. environmental compatibility. Further development projects will aim at the construction of practice-orientated plants in which combustion, heat extraction and recovery of aluminium oxide is combined. A further aim is the melting burner to which aluminium is supplied in form of wires, cuttings or rods. (BWI).

  2. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (paluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium.

  3. Primary targeting of recombinant Fv-immunotoxin hscFv25-mTNFα against hepatocellular carcinoma

    Institute of Scientific and Technical Information of China (English)

    Jing Zhang; Yan-Fang Liu; Shou-Jing Yang; Qing Qiao; Hong Cheng; Chuan-Shan Zhang; Fu-Cheng Ma; Hua-Zhang Guo

    2004-01-01

    AIM: To obtain human recombinant Fv-immunotoxin hscFv25-mTNFα (mutant human TNFα fused to human scFv25) against hepatocellular carcinoma (HCC). METHODS: Two relevant sites of enzymatic digestion were added to mTNFα by PCR. mTNFα was linked to the 3' end of hscFv25 in pGEX4T-1 vector. This anti-HCC recombinant Fv-immunotoxin hscFv25-mTNFα was expressed in Escherichia coliand purified from inclusions. After purified by glutathione-S-transferase affinity chromatography and thrombin digestion, it was identified by electrophoresis and Western blot. And then, the purified recombinant Fv immunotoxin was injected into nude mice with HCC xenografts through their tail veins. mTNFα protein and PBS were used as control at the same time. After treated for two weeks, nude mice were executed. The bulk and weight of tumors were observed. The tumor tissues were stained by immunohistochemical method with TNFα antibody.RESULTS: The expression ratio of recombinant Fv-immunotoxin hscFv25-mTNFα was 12% of bacterial protein. The result of tumor restraining trials of hscFv25-mTNFα showed 2/5 complete remission and 3/5 partial remission. mTNFα restraining trials showed 5/5 partial remission. The therapeutic result of hscFv25- mTNFα was better than that of mTNFα (F=8.70, P<0.05). The hscFv25-mTNFα remedial tumor tissues were positive for TNFα by immunohistochemical staining. The positive granules mainly existed in the cytoplasm of tumor cell. CONCLUSION: Recombinant Fv-immunotoxin hscFv25-mTNFα has better therapeutic effect than mTNFα. Tt can inhibit the cellular growth of HCC and has some potential of clinical application.

  4. A viral vectored prime-boost immunization regime targeting the malaria Pfs25 antigen induces transmission-blocking activity.

    Directory of Open Access Journals (Sweden)

    Anna L Goodman

    Full Text Available The ookinete surface protein Pfs25 is a macrogamete-to-ookinete/ookinete stage antigen of Plasmodium falciparum, capable of exerting high-level anti-malarial transmission-blocking activity following immunization with recombinant protein-in-adjuvant formulations. Here, this antigen was expressed in recombinant chimpanzee adenovirus 63 (ChAd63, human adenovirus serotype 5 (AdHu5 and modified vaccinia virus Ankara (MVA viral vectored vaccines. Two immunizations were administered to mice in a heterologous prime-boost regime. Immunization of mice with AdHu5 Pfs25 at week 0 and MVA Pfs25 at week 10 (Ad-MVA Pfs25 resulted in high anti-Pfs25 IgG titers, consisting of predominantly isotypes IgG1 and IgG2a. A single priming immunization with ChAd63 Pfs25 was as effective as AdHu5 Pfs25 with respect to ELISA titers at 8 weeks post-immunization. Sera from Ad-MVA Pfs25 immunized mice inhibited the transmission of P. falciparum to the mosquito both ex vivo and in vivo. In a standard membrane-feeding assay using NF54 strain P. falciparum, oocyst intensity in Anopheles stephensi mosquitoes was significantly reduced in an IgG concentration-dependent manner when compared to control feeds (96% reduction of intensity, 78% reduction in prevalence at a 1 in 5 dilution of sera. In addition, an in vivo transmission-blocking effect was also demonstrated by direct feeding of immunized mice infected with Pfs25DR3, a chimeric P. berghei line expressing Pfs25 in place of endogenous Pbs25. In this assay the density of Pfs25DR3 oocysts was significantly reduced when mosquitoes were fed on vaccinated as compared to control mice (67% reduction of intensity, 28% reduction in prevalence and specific IgG titer correlated with efficacy. These data confirm the utility of the adenovirus-MVA vaccine platform for the induction of antibodies with transmission-blocking activity, and support the continued development of this alternative approach to transmission-blocking malaria subunit

  5. Effect of aluminium phosphate as admixture on oxychloride cement

    Indian Academy of Sciences (India)

    M P S Chandrawat; R N Yadav

    2000-02-01

    The effect of admixing of aluminium phosphate on oxychloride cement in the matrix has been investigated. It is shown that aluminium phosphate retards the setting process of the cement and improves water-tightness.

  6. Structural colours and applications to anodised aluminium surfaces

    DEFF Research Database (Denmark)

    Johansen, Villads Egede

    This thesis investigates possible ways of creating aluminium with a milky white, metallic appearance for decorative purposes. Since white cannot be obtained through traditional absorption based dyeing of aluminium, optical mechanisms based on scattering by nanostructures are studied in order...

  7. Solidification of spent TBP solvent with aluminium chloride compounds

    International Nuclear Information System (INIS)

    The new techniques for processing spent TBP was investigated. It was proved that treatment of TBP containing DBP with aluminium chloride resulted in the formation of aluminium phosphate suitable for long term storage and final disposal

  8. Residual stress in 7449 aluminium alloy forgings

    International Nuclear Information System (INIS)

    The through thickness residual stress distributions within three 120 mm thick rectilinear forgings, made from the high strength aluminium alloy 7449 have been measured using both neutron diffraction and deep hole drilling. Neutron diffraction measurements were made on two instruments, one using a pulsed spallation neutron source, the other a steady state reactor source. Heat treatment of the forgings included a rapid quench into cold water and it was the residual stresses arising from this step that were initially measured. Neutron diffraction measurements indicated large magnitude (>250 MPa) tensile residual stresses in the centre of an as quenched forging, balanced by surface regions stressed in compression (<-200 MPa). Sufficient measurements were made to permit the description of the residual stress distribution using area maps. Two forgings were stress relieved by cold compression immediately after quenching. The degree of plastic strain was either 2.5% or 4%, and was applied by a single application of force in the short transverse direction. Cold compressed forgings were found to have far lower residual stress when compared to the as quenched condition. The amount of cold compression was found to cause an insignificant difference in the final residual stress distribution. The neutron diffraction results are compared to measurements made by deep hole drilling and a new incremental variation of the technique. The deep hole was drilled through the centre of the forgings in the short transverse direction. Multiple neutron diffraction measurements were also made on the extracted cores from the deep hole measurements to assess the variation of the unstrained lattice parameter through the thickness of the forgings.

  9. Does aluminium bind to histidine? An NMR investigation of amyloid β12 and amyloid β16 fragments.

    Science.gov (United States)

    Narayan, Priya; Krishnarjuna, Bankala; Vishwanathan, Vinaya; Jagadeesh Kumar, Dasappa; Babu, Sudhir; Ramanathan, Krishna Venkatachala; Easwaran, Kalpathy Ramaier Katchap; Nagendra, Holenarasipur Gundurao; Raghothama, Srinivasarao

    2013-07-01

    Aluminium and zinc are known to be the major triggering agents for aggregation of amyloid peptides leading to plaque formation in Alzheimer's disease. While zinc binding to histidine in Aβ (amyloid β) fragments has been implicated as responsible for aggregation, not much information is available on the interaction of aluminium with histidine. In the NMR study of the N-terminal Aβ fragments, DAEFRHDSGYEV (Aβ12) and DAEFRHDSGYEVHHQK (Aβ16) presented here, the interactions of the fragments with aluminium have been investigated. Significant chemical shifts were observed for few residues near the C-terminus when aluminium chloride was titrated with Aβ12 and Aβ16 peptides. Surprisingly, it is nonhistidine residues which seem to be involved in aluminium binding. Based on NMR constrained structure obtained by molecular modelling, aluminium-binding pockets in Aβ12 were around charged residues such as Asp, Glu. The results are discussed in terms of native structure propagation, and the relevance of histidine residues in the sequences for metal-binding interactions. We expect that the study of such short amyloid peptide fragments will not only provide clues for plaque formation in aggregated conditions but also facilitate design of potential drugs for these targets. PMID:23464626

  10. Advances in development and application of aluminium batteries

    DEFF Research Database (Denmark)

    Qingfeng, Li; Zhuxian, Qiu

    2001-01-01

    Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation o...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

  11. Friction stir welding (FSW) of aluminium foam sandwich panels

    OpenAIRE

    M. Bušić; Kožuh, Z.; D. Klobčar; Samardžić, I.

    2016-01-01

    The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and f...

  12. Aluminium allergy and granulomas induced by vaccinations for children

    DEFF Research Database (Denmark)

    Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

    2014-01-01

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

  13. Stability of aluminium beams in case of fire

    NARCIS (Netherlands)

    Meulen, O.R. van der; Soetens, F.; Maljaars, J.

    2014-01-01

    Fire is often the dominant design criterion for aluminium structures. Present design rules for aluminium constructions in fire neglect both the decrease in susceptibility to local buckling and the effects of creep, that are intrinsic to aluminium. They may therefore either overestimate or underestim

  14. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  15. Qimingxing Aluminium of Jinma Group Ceases Production

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>Jinma Group announced on December 23 that its subsidiary Meishan Qimingxing Aluminium decided to cease production starting from De- cember 23,and that the company will keep a close eye to the market and will resume pro- duction once the market bounces back.In 2007, Jinma Group took over Meishan Qimingxing’s 40% share by 112 million yuan to enter the aluminium industry.Meishan Qimingxing’s assets include a 125,000-ton production line of aluminium and 168 300KA electrolytic baths. Affected by the state’s macro-regulation policy in early years,the company’s profit fell short of estimates.Net profit of Meishan Qimingxing in 2007 was 10.65 million yuan.

  16. Diamond grooving of rapidly solidified optical aluminium

    Science.gov (United States)

    Abou-El-Hossein, Khaled; Hsu, Wei-Yao; Ghobashy, Sameh; Cheng, Yuan-Chieh; Mkoko, Zwelinzima

    2015-10-01

    Traditional optical aluminium grades such as Al 6061 are intensively used for making optical components for applications ranging from mould insert fabrication to laser machine making. However, because of their irregular microstructure and relative inhomogeneity of material properties at micro scale, traditional optical aluminium may exhibit some difficulties when ultra-high precision diamond turned. Inhomogeneity and micro-variation in the material properties combined with uneven and coarse microstructure may cause unacceptable surface finish and accelerated tool wear, especially in grooving operation when the diamond tool edge is fully immersed in the material surface. Recently, new grades of optical aluminium that are featured by their ultra-fine microstructure and improved material properties have been developed to overcome the problem of high tool wear rates. The new aluminium grades have been developed using rapid solidification process which results in extremely small grain sizes combined with improved mechanical properties. The current study is concerned with investigating the performance of single-point diamond turning when grooving two grades of rapidly solidified aluminium (RSA) grades: RSA905 which is a high-alloyed aluminium grade and RSA443 which has a high silicon content. In this study, two series of experiments employed to create radial microgrooves on the two RSA grades. The surface roughness obtained on the groove surface is measured when different combinations of cutting parameters are used. Cutting speed is varied while feed rate and depth of cut were kept constant. The results show that groove surface roughness produced on RSA443 is higher than that obtained on RSA905. Also, the paper reports on the effect of cutting speed on surface roughness for each RSA grade.

  17. Gene Regulatory Scenarios of Primary 1,25-Dihydroxyvitamin D{sub 3} Target Genes in a Human Myeloid Leukemia Cell Line

    Energy Technology Data Exchange (ETDEWEB)

    Ryynänen, Jussi; Seuter, Sabine [School of Medicine, Institute of Biomedicine, University of Eastern Finland, POB 1627, Kuopio FI-70211 (Finland); Campbell, Moray J. [Department of Pharmacology and Therapeutics, Roswell Park Cancer Institute, Elm and Carlton Streets, Buffalo, NY 14263 (United States); Carlberg, Carsten, E-mail: carsten.carlberg@uef.fi [School of Medicine, Institute of Biomedicine, University of Eastern Finland, POB 1627, Kuopio FI-70211 (Finland)

    2013-10-16

    Genome- and transcriptome-wide data has significantly increased the amount of available information about primary 1,25-dihydroxyvitamin D{sub 3} (1,25(OH){sub 2}D{sub 3}) target genes in cancer cell models, such as human THP-1 myelomonocytic leukemia cells. In this study, we investigated the genes G0S2, CDKN1A and MYC as master examples of primary vitamin D receptor (VDR) targets being involved in the control of cellular proliferation. The chromosomal domains of G0S2 and CDKN1A are 140–170 kb in size and contain one and three VDR binding sites, respectively. This is rather compact compared to the MYC locus that is 15 times larger and accommodates four VDR binding sites. All eight VDR binding sites were studied by chromatin immunoprecipitation in THP-1 cells. Interestingly, the site closest to the transcription start site of the down-regulated MYC gene showed 1,25(OH){sub 2}D{sub 3}-dependent reduction of VDR binding and is not associated with open chromatin. Four of the other seven VDR binding regions contain a typical DR3-type VDR binding sequence, three of which are also occupied with VDR in macrophage-like cells. In conclusion, the three examples suggest that each VDR target gene has an individual regulatory scenario. However, some general components of these scenarios may be useful for the development of new therapy regimens.

  18. CDC25A phosphatase is a target of E2F and is required for efficient E2F-induced S phase

    DEFF Research Database (Denmark)

    Vigo, E; Müller, H; Prosperini, E;

    1999-01-01

    to the estrogen receptor ligand binding domain (ER). In this study, we demonstrated that activation of all three E2Fs could relieve the mitogen requirement for entry into S phase in Rat1 fibroblasts and that E2F activity leads to a shortening of the G(0)-G(1) phase of the cell cycle by 6 to 7 h. In contrast...... in the absence of protein synthesis. Furthermore, CDC25A is defined as a novel E2F target whose expression can be directly regulated by E2F-1. Data showing that CDC25A is an essential target for E2F-1, since its activity is required for efficient induction of S phase by E2F-1, are provided. Finally, our results...... show that expression of two E2F target genes, namely CDC25A and cyclin E, is sufficient to induce entry into S phase in quiescent fibroblasts. Taken together, our results provide an important step in defining how E2F activity leads to deregulated proliferation....

  19. New aluminium alloys with high lithium content

    Energy Technology Data Exchange (ETDEWEB)

    Schemme, K.; Velten, B.

    1989-06-01

    Since the early 80's there have been made great efforts to replace the high strength aluminium alloys for the aircraft and space industry by a new generation of aluminium-lithium alloys. The attractivity of this kind of alloys could be increased by a further reduction of their density, caused by an increasing lithium content (/ge/ 5 wt.% Li). Therefore binary high-lithium containing alloys with low density are produced and metallografically investigated. A survey of their strength and wear behavior is given by using tensile tests and pin abrasing tests. (orig.).

  20. Aluminium induced oxidative stress results in decreased mitochondrial biogenesis via modulation of PGC-1α expression

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Kandimalla, Ramesh J.L. [Department of Biochemistry, Postgraduate Institute of Medical Education and Research, Chandigarh 160012 (India); Bal, Amanjit [Department of Histopathology, Postgraduate Institute of Medical Education and Research, Chandigarh (India); Gill, Kiran Dip, E-mail: kdgill2002@yahoo.co.in [Department of Biochemistry, Postgraduate Institute of Medical Education and Research, Chandigarh 160012 (India)

    2013-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the effects of aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of Peroxisome proliferator activated receptor gamma co-activator 1α (PGC-1α) and its downstream targets i.e. Nuclear respiratory factor-1(NRF-1), Nuclear respiratory factor-2(NRF-2) and Mitochondrial transcription factor A (Tfam) in mitochondrial biogenesis. Aluminium lactate (10 mg/kg b.wt./day) was administered intragastrically to rats for 12 weeks. After 12 weeks of exposure, we found an increase in ROS levels, mitochondrial DNA oxidation and decrease in citrate synthase activity in the Hippocampus (HC) and Corpus striatum (CS) regions of rat brain. On the other hand, there was a decrease in the mRNA levels of the mitochondrial encoded subunits–NADH dehydrogenase (ND) subunits i.e. ND1, ND2, ND3, Cytochrome b (Cytb), Cytochrome oxidase (COX) subunits i.e. COX1, COX3, ATP synthase (ATPase) subunit 6 along with reduced expression of nuclear encoded subunits COX4, COX5A, COX5B of Electron transport chain (ETC). Besides, a decrease in mitochondrial DNA copy number and mitochondrial content in both regions of rat brain was observed. The PGC-1α was down-regulated in aluminium treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α in aluminium treated rats. Electron microscopy results revealed a significant increase in the mitochondrial swelling, loss of cristae, chromatin condensation and decreases in mitochondrial number in case of aluminium treated rats as compared to control. So, PGC-1α seems to be a potent target for aluminium neurotoxicity, which makes it an almost ideal target to control or limit the damage that has been associated with the defective mitochondrial function seen in neurodegenerative diseases. - Highlights: • Aluminium decreases the mRNA levels of mitochondrial and nuclear encoded

  1. Hsa-miR-106b-25簇的靶基因预测及生物信息学分析%Target genes of the hsa-miR-106b-25 cluster:Prediction and bioinformatic analysis

    Institute of Scientific and Technical Information of China (English)

    宋亚芹; 付文博; 卢沐; 刘洋; 魏育涛

    2015-01-01

    目的 Hsa-miR-106b-25簇涉及肿瘤的多种生物学过程,文中对hsa-miR-106b-25簇:miR-106b、miR-93、miR-25进行靶基因的预测及功能分析,为进一步研究这3个miRNAs的功能及他们之间的相互作用调节机制提供线索. 方法 应用miRBase数据库获取miR-106 b、miR-93及miR-25的序列信息,选择TargetScan、PicTar、miRanda 3种在线靶基因预测软件分别预测它们的靶基因,取交集并结合miRTarbase数据库中3种及3种以上实验验证过的靶基因作为进一步生物信息学分析的基因集合;分别对基因集合进行生物过程的功能富集分析,pathway 分析及蛋白互作分析. 结果 hsa-miR-106b-25簇的预测靶基因富集于多个生物学过程及功能,其生物过程主要集中于:大分子新陈代谢调节、代谢过程的调节、细胞周期;KEGG通路主要富集于:胶质瘤、黑色素瘤、前列腺癌、胆囊癌等肿瘤相关通路,蛋白互作显示基因簇中3个成员miRNA的预测靶基因编码蛋白质间存在复杂的相互作用,靶基因KAT2B、PTEN、TP53、CDH1、MDM2、E2F1、RB1、SMAD7编码蛋白在互作网络中具有核心地位. 结论 miR-106 b-25簇中的3个成员通过调控细胞周期的转换作用于肿瘤通路过程进而调节下游靶蛋白参与肿瘤的发生过程.%Objective The hsa-miR-106b-25 gene cluster is involved in various biological processes of carcinoma .This study aims at a prediction and function analysis of the hsa-miR-106b-25 gene cluster, miR-106b, miR-93, and miR-25, so as to provide some evidence for further studies on the functions of the three miRNAs and the mechanisms of their interaction . Methods We obtained the sequences of miR-106b, miR-93, and miR-25 from the miRBase, predicted their target genes with TargetScan , PicTar, and miRanda, and used 3 or more experimentally verified target genes from the miRTarbase as the gene set for further bioinformatic analysis .We predic-ted the biological processes of the

  2. The determination of boron in aluminium of high purity

    International Nuclear Information System (INIS)

    A description is given of the investigations that led to the development of chemical methods for the determination of boron within the range 0,25 to 1,0 p.p.m. in aluminium of high purity. Methods were developed that incorporated fluorimetry, directly in solutions containing aluminium and after separation of boron by liquid-liquid extraction into 2-ethyl-1,3 hexanediol. A published spectrophotometric method, involving extraction of the BF4sup(-) complex with methylene blue into dichloroethane, was modified for application to alluminium samples. Details of this modified procedure and the fluorimetric-extraction procedure are appended. The precision of the methylene-blue method is about 6 percent relative and is recommended for precision and speed in preference to others. Separation of boron by distillation and spectrophotometric determination with curcumin gave low values in comparison with those obtained by the other methods. Agreement between the boron values obtained on the samples tested was good for the fluorimetric and methylene-blue spectrophotometric methods

  3. Experimental study of friction in aluminium bolted joints

    Directory of Open Access Journals (Sweden)

    Vincenzi N.

    2010-06-01

    Full Text Available This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces versus sixth tightening (spoiled surfaces. The study considers M8x1.25 8.8 galvanized screws.

  4. China’s Aluminium Consumption and the Related Policies

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>China is a major aluminium consumer country in the world. In 2005, China produced 7.81 million tons aluminium and imported 640,000 tons. Meanwhile, China also exported 1.32 million tons aluminium in 2005. China’s apparent consumption of aluminium in 2005 was about 7.1 million tons, which was 9.3 times over that in 1990. China’s aluminium consumption growth has kept at an annual average of 16.1 per cent since 1990, which makes China the

  5. China’s Production and Market of Aluminium Extruded Profiles

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Chinese aluminium extrusion industry came into existence at the early 1950s with most products used in military industry and national defence.At the beginning of 1980s,the produc- tion of construction aluminium profiles started simultaneously in North and South China.In the following thirty years,the aluminium extru- sion industry entered into a quickly developing stage with a focus on construction aluminium profiles.With the blooming real estate industry, the demand for construction aluminium profiles from the domestic market has a tendency of yearly increase.From 2000,the quick devel- opments of China’s auto and railway vehicle

  6. miR-107 and miR-25 simultaneously target LATS2 and regulate proliferation and invasion of gastric adenocarcinoma (GAC) cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Mingjun; Wang, Xiaolei [Cancer Center, The Second Affiliated Hospital of Anhui Medical University, Hefei 230601 (China); Li, Wanhu [MRI Room of Shandong Cancer Hospital & Institute, Jinan 250117 (China); Cui, Yongchun, E-mail: yongchuncui1@126.com [Drug Clinical Trial Institution of Shandong Cancer Hospital & Institute, #440, Jiyan Road, Jinan 250117 (China)

    2015-05-08

    Although a series of oncogenes and tumor suppressors were identified in the pathological development of gastric adenocarcinoma (GAC), the underlying molecule mechanism were still not fully understood. The current study explored the expression profile of miR-107 and miR-25 in GAC patients and their downstream regulative network. qRT-PCR analysis was performed to quantify the expression of these two miRNAs in serum samples from both patients and healthy controls. Dual luciferase assay was conducted to verify their putative bindings with LATS2. MTT assay, cell cycle assay and transwell assay were performed to explore how miR-107 and miR-25 regulate proliferation and invasion of gastric cancer cells. Findings of this study demonstrated that total miR-107 or miR-25 expression might be overexpressed in gastric cancer patients and they can simultaneously and synchronically regulate LATS2 expression, thereby affecting gastric cancer cell growth and invasion. Therefore, the miR-25/miR-107-LATS2 axis might play an important role in proliferation and invasion of the gastric cancer cells. - Highlights: • Total miR-107 and miR-25 expression is significantly increased in GAC patients. • Both miR-107 and miR-25 can promote proliferation and invasion of GAC cells. • Both miR-107 and miR-25 can target LATS2 and regulate its expression. • miR-107 and miR-25 regulate proliferation and invasion of GAC cells though LATS2.

  7. Pengaruh Partisipasi Penyusunan Anggaran, Kejelasan Sasaran Anggaran, Akuntabilitas Publik, dan Pengendalian Akuntansi Terhadap Kinerja Manajerial pada PT. INDONESIA ASAHAN ALUMINIUM (Persero)

    OpenAIRE

    Rangkuti, Riska Maysarah

    2016-01-01

    This study aims to examine the impact of budgeting participation, budget targets clarity, public accountibilty, and accounting control on managerial performance at PT Indonesia asahan Aluminium ( persero) this type of research is classifield as causal associative research.the population of this study is the PT Indonesia Asahan Aluminium (Persero ) the sample are selective by secured sampling methods with 40 respondens.the data that used in this study are primary data.the technique of data col...

  8. THE SOLAR NEIGHBORHOOD. XXIII. CCD PHOTOMETRIC DISTANCE ESTIMATES OF SCR TARGETS-77 M DWARF SYSTEMS WITHIN 25 pc

    International Nuclear Information System (INIS)

    We present CCD photometric distance estimates of 100 SCR (SuperCOSMOS RECONS) systems with μ ≥ 0.''18 yr-1, 29 of which are new discoveries previously unpublished in this series of papers. These distances are estimated using a combination of new VRI photometry acquired at CTIO and JHK magnitudes extracted from 2MASS. The estimates are improvements over those determined using photographic plate BRI magnitudes from SuperCOSMOS plus JHK, as presented in the original discovery papers. In total, 77 of the 100 systems investigated are predicted to be within 25 pc. If all 77 systems are confirmed to have πtrig ≥ 40 mas, this sample would represent a 23% increase in M dwarf systems nearer than 25 pc in the southern sky.

  9. A Viral Vectored Prime-Boost Immunization Regime Targeting the Malaria Pfs25 Antigen Induces Transmission-Blocking Activity

    OpenAIRE

    Goodman, Anna L.; Blagborough, Andrew M.; Sumi Biswas; Yimin Wu; Hill, Adrian V.; Sinden, Robert E.; Draper, Simon J

    2011-01-01

    The ookinete surface protein Pfs25 is a macrogamete-to-ookinete/ookinete stage antigen of Plasmodium falciparum, capable of exerting high-level anti-malarial transmission-blocking activity following immunization with recombinant protein-in-adjuvant formulations. Here, this antigen was expressed in recombinant chimpanzee adenovirus 63 (ChAd63), human adenovirus serotype 5 (AdHu5) and modified vaccinia virus Ankara (MVA) viral vectored vaccines. Two immunizations were administered to mice in a ...

  10. Molecular breeding of cereals for aluminium resistance

    Science.gov (United States)

    Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

  11. Experimental analysis of cut welding in aluminium

    DEFF Research Database (Denmark)

    Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

    1993-01-01

    Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...

  12. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P;

    2005-01-01

    in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...

  13. Indentation of aluminium foam at low velocity

    Directory of Open Access Journals (Sweden)

    Shi Xiaopeng

    2015-01-01

    Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

  14. Microstructure Development during Solidification of Aluminium Alloys

    NARCIS (Netherlands)

    Ruvalcaba Jimenez, D.G.

    2009-01-01

    This Thesis demonstrates studies on microstructure development during the solidification of aluminium alloys. New insights of structure development are presented here. Experimental techniques such as quenching and in-situ High-brilliance X-ray microscopy were utilized to study the microstructure evo

  15. 1,25-Dihydroxyvitamin D3 Controls a Cohort of Vitamin D Receptor Target Genes in the Proximal Intestine That Is Enriched for Calcium-regulating Components.

    Science.gov (United States)

    Lee, Seong Min; Riley, Erin M; Meyer, Mark B; Benkusky, Nancy A; Plum, Lori A; DeLuca, Hector F; Pike, J Wesley

    2015-07-17

    1,25-Dihydroxyvitamin D3 (1,25(OH)2D3) plays an integral role in calcium homeostasis in higher organisms through its actions in the intestine, kidney, and skeleton. Interestingly, although several intestinal genes are known to play a contributory role in calcium homeostasis, the entire caste of key components remains to be identified. To examine this issue, Cyp27b1 null mice on either a normal or a high calcium/phosphate-containing rescue diet were treated with vehicle or 1,25(OH)2D3 and evaluated 6 h later. RNA samples from the duodena were then subjected to RNA sequence analysis, and the data were analyzed bioinformatically. 1,25(OH)2D3 altered expression of large collections of genes in animals under either dietary condition. 45 genes were found common to both 1,25(OH)2D3-treated groups and were composed of genes previously linked to intestinal calcium uptake, including S100g, Trpv6, Atp2b1, and Cldn2 as well as others. An additional distinct network of 56 genes was regulated exclusively by diet. We then conducted a ChIP sequence analysis of binding sites for the vitamin D receptor (VDR) across the proximal intestine in vitamin D-sufficient normal mice treated with vehicle or 1,25(OH)2D3. The residual VDR cistrome was composed of 4617 sites, which was increased almost 4-fold following hormone treatment. Interestingly, the majority of the genes regulated by 1,25(OH)2D3 in each diet group as well as those found in common in both groups contained frequent VDR sites that likely regulated their expression. This study revealed a global network of genes in the intestine that both represent direct targets of vitamin D action in mice and are involved in calcium absorption.

  16. Au25 cluster functionalized metal-organic nanostructures for magnetically targeted photodynamic/photothermal therapy triggered by single wavelength 808 nm near-infrared light

    Science.gov (United States)

    Yang, Dan; Yang, Guixin; Gai, Shili; He, Fei; An, Guanghui; Dai, Yunlu; Lv, Ruichan; Yang, Piaoping

    2015-11-01

    Near-infrared (NIR) light-induced cancer therapy has gained considerable interest, but pure inorganic anti-cancer platforms usually suffer from degradation issues. Here, we designed metal-organic frameworks (MOFs) of Fe3O4/ZIF-8-Au25 (IZA) nanospheres through a green and economic procedure. The encapsulated Fe3O4 nanocrystals not only produce hyperthemal effects upon NIR light irradiation to effectively kill tumor cells, but also present targeting and MRI imaging capability. More importantly, the attached ultrasmall Au25(SR)18- clusters (about 2.5 nm) produce highly reactive singlet oxygen (1O2) to cause photodynamic effects through direct sensitization under NIR light irradiation. Furthermore, the Au25(SR)18- clusters also give a hand to the hyperthemal effect as photothermal fortifiers. This nanoplatform exhibits high biocompatibility and an enhanced synergistic therapeutic effect superior to any single therapy, as verified by in vitro and in vivo assay. This image-guided therapy based on a metal-organic framework may stimulate interest in developing other kinds of metal-organic materials with multifunctionality for tumor diagnosis and therapy.Near-infrared (NIR) light-induced cancer therapy has gained considerable interest, but pure inorganic anti-cancer platforms usually suffer from degradation issues. Here, we designed metal-organic frameworks (MOFs) of Fe3O4/ZIF-8-Au25 (IZA) nanospheres through a green and economic procedure. The encapsulated Fe3O4 nanocrystals not only produce hyperthemal effects upon NIR light irradiation to effectively kill tumor cells, but also present targeting and MRI imaging capability. More importantly, the attached ultrasmall Au25(SR)18- clusters (about 2.5 nm) produce highly reactive singlet oxygen (1O2) to cause photodynamic effects through direct sensitization under NIR light irradiation. Furthermore, the Au25(SR)18- clusters also give a hand to the hyperthemal effect as photothermal fortifiers. This nanoplatform exhibits high

  17. The Solar Neighborhood XXIII CCD Photometric Distance Estimates of SCR Targets -- 77 M Dwarf Systems within 25 Parsecs

    CERN Document Server

    Winters, Jennifer G; Jao, Wei-Chun; Subasavage, John P; Finch, Charlie T; Hambly, Nigel C

    2010-01-01

    We present CCD photometric distance estimates of 100 SCR (SuperCOSMOS RECONS) systems with $\\mu$ $\\geq$ 0$\\farcs$18/yr, 28 of which are new discoveries previously unpublished in this series of papers. These distances are estimated using a combination of new $VRI$ photometry acquired at CTIO and $JHK$ magnitudes extracted from 2MASS. The estimates are improvements over those determined using photographic plate $BRI$ magnitudes from SuperCOSMOS plus $JHK$, as presented in the original discovery papers. In total, 77 of the 100 systems investigated are predicted to be within 25 pc. If all 77 systems are confirmed to have $\\pi

  18. Antiproton Target

    CERN Multimedia

    1980-01-01

    Antiproton target used for the AA (antiproton accumulator). The first type of antiproton production target used from 1980 to 1982 comprised a rod of copper 3mm diameter and 120mm long embedded in a graphite cylinder that was itself pressed into a finned aluminium container. This assembly was air-cooled and it was used in conjunction with the Van der Meer magnetic horn. In 1983 Fermilab provided us with lithium lenses to replace the horn with a view to increasing the antiproton yield by about 30%. These lenses needed a much shorter target made of heavy metal - iridium was chosen for this purpose. The 50 mm iridium rod was housed in an extension to the original finned target container so that it could be brought very close to the entrance to the lithium lens. Picture 1 shows this target assembly and Picture 2 shows it mounted together with the lithium lens. These target containers had a short lifetime due to a combination of beam heating and radiation damage. This led to the design of the water-cooled target in...

  19. Experimental weathering rates of aluminium silicates

    International Nuclear Information System (INIS)

    The chemical weathering of primary rocks and minerals in natural systems has a major impact on soil development and its composition. Chemical weathering is driven to a large extent by mineral dissolution. Through mineral dissolution, elements are released into groundwater and can readily react to precipitate secondary minerals such as clays, zeolites, and carbonates. Carbonates form from divalent cations (e.g. Ca, Fe and Mg) and CO2, and kaolin clay and gibbsite formation is attributed to the weathering of aluminium-rich minerals, most notably the feldspars. The CarbFix Project in Hellisheidi (SW-Iceland) aims to use natural weathering processes to form carbonate minerals by the re-injection of CO2 from a geothermal power plant back into surrounding basaltic rocks. This process is driven by the dissolution of basaltic rocks, rich in divalent cations, which can combine with injected CO2 to form and precipitate carbonates. This thesis focuses on the dissolution behaviour of Stapafell crystalline basalt, which consists of three major phases (plagioclase, pyroxene, and olivine) and is rich in divalent cations. Steady-state element release rates from crystalline basalt at far-from-equilibrium conditions were measured at pH from 2 to 11 and temperatures from 5 to 75 C in mixed-flow reactors. Steady-state Si and Ca release rates exhibit a U-shaped variation with pH, where rates decrease with increasing pH at acid condition but increase with increasing pH at alkaline conditions. Silicon release rates from crystalline basalt are comparable to Si release rates from basaltic glass of the same chemical composition at low pH and temperatures ≥25 C but slower at alkaline pH and temperatures ≥50 C. In contrast, Mg and Fe release rates decrease continuously with increasing pH at all temperatures. This behaviour is interpreted to stem from the contrasting dissolution behaviours of the three major minerals comprising the basalt: plagioclase, pyroxene, and olivine. Element

  20. Single-Proton Pickup Reaction of the Halo Nucleus 6He on a 9Be Target at 25 MeV/nucleon

    Institute of Scientific and Technical Information of China (English)

    PANG Dan-Yang; LOU Jian-Ling; LU Fei; FAN Feng-Ying; A. Ozawa; Y. Yamaguchi; R. Kanungo; D. Fang; I. Tanihata; YE Yan-Lin; JIANG Dong-Xing; ZHENG Tao; LI Zhi-Huan; LI Xiang-Qing; GE Yu-Cheng; HUA Hui; WU Cui-E

    2007-01-01

    The inclusive differential cross sections of the 7 Li nucleus in a reaction induced by 6He on a 9Be target are measured at an incident energy of 25 MeV/nucleon. Finite-range distorted-wave Born approximation calculations suggest that these 7 Li particles are formed in a direct single-proton pickup reaction 9 Be(6 He, 7 Li)8 Li. The experimental data can be well reproduced by taking into account of the contributions of both the ground states and the first excited states of 7 Li and 8 Li.

  1. Phase analysis of aluminium modified GeSbTe bulk prepared from XRD of samples

    Science.gov (United States)

    Sandhu, Sharanjit; Singh, D.; Kumar, S.; Thangaraj, R.

    2016-05-01

    Various compositions of Aluminium modified GST as Alx(Ge2Sb2Te5)1-x x= 0, 0.15, 0.20, 0.25, 0.30 are prepared to study as a phase change material. Bulk prepared is studied with XRD scans for various phases formed. Phases other than Ge2Sb2Te5 do come in but dominated one is Ge2Sb2Te5 hexagonal phase.

  2. Extraction chromatography of aluminium(Ⅲ) and mutual separation of aluminium ( Ⅲ ) , gallium ( Ⅲ ), indium ( Ⅲ )and thallium ( Ⅲ ) with N-n-octylaniline%Extraction chromatography of aluminium(Ⅲ) and mutual separation of aluminium ( Ⅲ ),gallium ( Ⅲ ),indium ( Ⅲ )and thallium ( Ⅲ ) with N-n-octylaniline

    Institute of Scientific and Technical Information of China (English)

    Sachin R PHULE; Haribhau R AHER; Shashikant R KUCHEKAR; Sung-H HAN

    2012-01-01

    A selective method has been developed for the extraction chromatography of aluminium (Ⅲ) and its separation from several metal ions with a chromatographic column containing N-n-octylaniline (a liquid anion exchanger) coated on silanized silica gel as a stationary phase.The aluminium (Ⅲ) was quantitatively extracted with the 0.065 mol/L N-n-octylaniline in 0.013 to 0.05 mol/L sodium succinate at a flow rate of 1.0 mL/min.The extracted metal ion has been recovered by eluting with 25.0 mL of 0.05 mol/L hydrochloric acid and estimated spectrophotometrically with aurintricarboxylic acid.The effects of the acid concentration,the reagent concentration,the flow rate and the eluting agents have been investigated.The log-log plots of distribution coefficient ( Kd ( Al (Ⅲ ) ) ) versus N-n-octylaniline concentration in 0.005 and 0.007 mol/L sodium succinate gave the slopes of 0.5 and 0.7 respectively and showed the probable composition of the extracted species was 1∶1 (metal to amine ratio) and the nature of extracted species was [ RR'NH2+ Al succinate2- ] org.The extraction of aluminium(Ⅲ) was carried out in the presence of various ions to ascertain the tolerance limit of individual ions.Aluminium (Ⅲ) has been separated from multicomponent mixtures,pharmaceutical samples and synthetic mixtures corresponding to alloys.A scheme for mutual separation of aluminium (Ⅲ),indium (Ⅲ),gallium (Ⅲ) and thallium(Ⅲ) has been developed by using suitable masking agents.The method is fast,accurate and precise.

  3. First wall design of aluminium alloy R-tokamak

    International Nuclear Information System (INIS)

    A design study of a low-activation D-T tokamak Reacting Plasma Project In Nagoya has been finished. The study emphasizes the vacuum vessel and the bumper limiter. Our choice of materials (aluminium vacuum vessel, copper conductors, aluminium TF coil case and lead shield) results in a radiation level of about 1 x 10-3 times that of a TFTR type design, and 1 x 10-4 times that of JET type design, at 2 weeks after one D-T shot. Thick graphite tiles will be fixed directly on the aluminium vacuum vessel using aluminium spring washers and bolts. With this simplified structure of the bumper limiter, the inner surface temperature of the thick aluminium vacuum vessel will be less than 1200C which is required to reduce the overaging effect of the aluminium alloy. (orig.)

  4. What is the risk of aluminium as a neurotoxin?

    Science.gov (United States)

    Exley, Christopher

    2014-06-01

    Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

  5. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention.

  6. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as permeability were observed for any of the three diatoms suggesting that mechanisms of aluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. PMID:26921729

  7. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. PMID:25687835

  8. Straggling of heavy ions in aluminium

    International Nuclear Information System (INIS)

    An effort has been made to determine the straggling in aluminium of 4He, 16O and 35Cl ions of different energies produced by the tandem Van de Graaff at Harwell. The technique consists of scattering the accelerated and collimated ions in a scattering chamber from a 0.100 mg/cm2 gold foil, allowing the scattered ions to pass through a two aperture collimator, using different aluminium foils over one of the apertures and stopping the two emergent beams in a good quality silicon surface barrier detector the output of which is connected to a 4096 channel analyser. The energy widths obtained in the case of helium ions are in fair agreement with both the Bloch and the recent Tschalar (1968) theory. The measured widths in the case of heavy ions are very large and can be explained only if account is taken of their charge distributions in foils. This study should be useful in ion implantation work. (author)

  9. China will Reduce Aluminium Export in 2005

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>Starting from January 1, 2005, China eliminated the 8 per cent export tax rebate for aluminium, and further more, the exporters will have to pay 5 per cent export tax. This is beyond the expectations of the producers, for most of them thought only the 8 per cent export tax rebate would be eliminated and it was still too early to add the export tax.

  10. FSW characterization of 6082 aluminium alloys sheets

    OpenAIRE

    K. Mroczka; A. Pietras

    2009-01-01

    Purpose: The purpose of the investigations was to elaborate a set of FSW parameters for connecting 6082 aluminium alloy sheets allowing to produce welds of highest strength.Design/methodology/approach: The FSW was tried at different speeds and at additional cooling. The welds microstructure was studied using optical and scanning electron microscopes. The mechanical properties of produced connections are discussed regarding their tensile test and microhardness measurements.Findings: The FSW we...

  11. Methods of inoculation of pure aluminium structure

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2008-03-01

    Full Text Available Purpose: The main aim of investigations was the reduction of grain size and unification of structure for pure Al casting by introduction of small amount of inoculant (less than obligatory standart PN-EN 573-3, which concerning about aluminium purity, with electromagnetic field and variable casting parameters.Design/methodology/approach: To investigations it was used light microscopy and TEM. Surfaces of samples which were prepared for macro- and microstructure analysis were etched with use of solution of: 50g Cu, 400ml HCl, 300ml HNO3 and 300ml H2O. Thin foils for TEM investigations were electropolished with use of 20 ml HClO4 and 80ml CH3OH.Findings: The results of investigations and their analysis show possibility of effective inoculation of pure aluminium structure by use of some factors such as: different materials of the mould, influencing of stirring electromagnetic field into metal during solidification, inoculation by introducing AlTi5B1 inoculant into liquid aluminium and changing the pouring temperature.Research limitations/implications: I further research, authors of this paper are going to application of introduced method of inoculation in industrial tests.Practical implications: The work presents refinement of structure method which are particularly important in continuous and semi – continuous casting where products are used for plastic forming. Large columnar crystals zone result in forces extrusion rate reduction and during the ingot rolling delamination of external layers can occur. Thus, in some cases ingot skinning is needed, which rises the production costs.Originality/value: Contributes to research on size reduction in pure aluminium structure.

  12. Aluminium matrix composites fabricated by infiltration method

    OpenAIRE

    L.A. Dobrzański; M. Kremzer; A. J. Nowak; Nagel, A.

    2009-01-01

    Purpose: The aim of this work is to examine the structure and properties of metal matrix composites obtained by infiltration method of porous ceramic preforms by liquid aluminium alloy.Design/methodology/approach: Ceramic preforms were manufactured by the sintering method of ceramic powder. The preform material consists of powder Condea Al2O3 CL 2500, however, as the pore forming the carbon fibers Sigrafil C10 M250 UNS were used. Then ceramic preforms were infiltrated with liquid eutectic EN ...

  13. Softening Behaviour of Selected Commercially Pure Aluminium Model Alloys

    OpenAIRE

    Sande, Gunnar

    2012-01-01

    A characterization of the softening behaviour of four different commercially pure aluminium alloys has been carried out. The work is related to the MOREAL project (Modelling towards value-added recycling friendly aluminium alloys), where the main goal is to quantify the effect of the elements in recyclable aluminium alloys on microstructure and mechanical properties during thermo-mechanical processing. Typical elements are iron (Fe), silicon (Si) and manganese (Mn), and the alloys studied in ...

  14. Un-optimistic Prospects for the Westward Movement of Aluminium

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>The westward movement of aluminium is essential for the industrial development.Up till now,the northwestern area has planned to construct more than 40 aluminium projects with a total production capacity of over 20 million tons.The future rate of progress of newly constructed projects are directly related to the supplies of the aluminium market,having critical guiding meaning for the trends of

  15. Friction factor of CP aluminium and aluminium–zinc alloys

    Indian Academy of Sciences (India)

    N Vidhya Sagar; K S Anand; A C Mithun; K Srinivasan

    2006-12-01

    Friction factor has been determined for CP aluminium and aluminium–zinc alloys using ring compression test at different temperatures from 303 K to 773 K. It is found that CP aluminium exhibits sticking whereas Al–Zn alloys do not exhibit sticking at elevated temperatures. Hot working of Al–Zn alloy is easier than that of CP aluminium at 773 K. As zinc content increases up to 10 wt% the friction factor decreases up to 0.02.

  16. Aluminium supplier selection for the automotive parts manufacturer

    OpenAIRE

    M. Cieśla

    2016-01-01

    This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method an...

  17. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    Directory of Open Access Journals (Sweden)

    B. Bobic

    2010-03-01

    Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

  18. Tribological characteristics of coatings on aluminium and its alloys

    OpenAIRE

    Abdul-Mahdi, Fadhil S

    1987-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. Hard anodising on aluminium and its alloys has been widely practised for many years in order to improve the resistance of the otherwise poor wear characteristics of aluminium. In recent years there has been an increasing interest in other treatments and coatings, on both aluminium and other base metals. The aim of this investigation is to explain the tribological performance and wear mechanis...

  19. Wearing tests on aluminium coated with diamond by triboadhesion

    Institute of Scientific and Technical Information of China (English)

    J.M.RodríguezLelis; B.D.Angulo; J.O.Colín; J.PorcayoCalderón

    2001-01-01

    In this work the results obtained from subjecting aluminium coated with diamond by tri-boadhesion to a wearing process with a plane rider. Here it is shown the ratio of the normal toshearing forces, called friction factor, as an indication of the resistance of the surface. It was foundthat the film of the aluminium coated with diamond resisted three times compared with the oxida-tion film of commercial aluminium, which for the purpose of this work was considered withoutcoating.

  20. Behaviour and design of aluminium alloy structural elements

    OpenAIRE

    Su, Meini; 蘇玫妮

    2014-01-01

    Aluminium alloys are nonlinear metallic materials with continuous stress-strain curves that are not well represented by the simplified elastic, perfectly plastic material model used in most existing design specifications. The aims of this study are to develop a more efficient design method for aluminium alloy structures by rationally exploiting strain hardening. The key components of this study include laboratory testing, numerical modelling and development of design guidance for aluminium al...

  1. Multiply-negatively charged aluminium clusters and fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Noelle

    2008-07-15

    Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

  2. Aluminium in the rail transportation market

    Energy Technology Data Exchange (ETDEWEB)

    Zehnder, J. [Alcan Alesa Engineering Ltd., Zurich (Switzerland). Alcan Mass Transportation Systems

    2002-07-01

    Rail-transportation is not, as one might expect, a homogeneous market but extremely fragmented and even with huge differences from continent to continent, i.e. in North America freight transport is dominating whereas in Europe passenger transport prevails. A first segmentation splits infrastructure from vehicles. In a second layer of segmentation we distinguish between light rail vehicles, heavy metros, regional trains, intercity trains, high speed trains with and without tilting, maglev trains, freight vehicles and locomotives. Finally, we find aluminium applications in wheels, suspension parts, brake equipment, traction equipment, body structure, hang on parts and interior trim. On the infrastructure side best use of aluminium is in the field of power supply. In order to have the best solution for each application, all forms of products such as castings, forgings, flat rolled products and extrusions are needed and the engineers are using a broad choice or different alloys for all the requirements such as structural strength, decorative aspect, electrical conductivity, wear resistance, weldability, corrosion resistance etc. Innovation cycles in rail transportation are very slow, mainly because the expected life of vehicles is over 30 years and so no fleet owner will run the risk of getting vehicles with non-proven components, i.e. where a safe life of over 30 years cannot be shown. In the following the most important aluminium applications are shown and discussed. (orig.)

  3. Plasmonic enhancement of photoluminescence from aluminium nitride

    Science.gov (United States)

    Flynn, Chris; Stewart, Matthew

    2016-03-01

    Aluminium nitride (AlN) films were grown on c-plane sapphire wafers by molecular beam epitaxy (MBE) under aluminium-rich conditions. The excess aluminium (Al) accumulated on the surface of the films as micro-scale droplets 1-10 μm in size, and as Al nanoparticles with diameters in the range 10-110 nm. Photoluminescence (PL) measurements were performed on the AlN samples using a 193 nm Excimer laser as the excitation source. Prior to PL measurements the wafers were cleaved in half. One half of each wafer was submitted to a 10 min treatment in H3PO4 heated to 70 °C to remove the excess Al from the film surface. The remaining half was left in the as-deposited condition. The mean intensities of the near-band-edge PL peaks of the as-deposited samples were 2.0-3.4 times higher compared to the samples subjected to the H3PO4 Al-removal treatment. This observation motivated calculations to determine the optimal Al surface nanosphere size for plasmonic enhancement of PL from AlN. The PL enhancement was found to peak for an Al nanosphere radius of 15 nm, which is within the range of the experimentally-observed Al nanoparticle sizes.

  4. Measurement of proton induced thick target γ-ray yields on B, N, Na, Al and Si from 2.5 to 4.1 MeV

    Science.gov (United States)

    Chiari, M.; Ferraccioli, G.; Melon, B.; Nannini, A.; Perego, A.; Salvestrini, L.; Lagoyannis, A.; Preketes-Sigalas, K.

    2016-01-01

    Thick target yields for proton induced γ-ray emission (PIGE) on low-Z nuclei, namely B, N, Na, Al and Si, were measured for proton energies from 2.5 to 4.1 MeV and emission angles of 0°, 45° and 90°, at the 3 MV Tandetron laboratory of INFN-LABEC in Florence. The studied reactions were: 10B(p,α‧γ)7Be (Eγ = 429 keV), 10B(p,p‧γ)10B (Eγ = 718 keV) and 11B(p,p‧γ)11B (Eγ = 2125 keV) for boron; 14N(p,p‧γ)14N (Eγ = 2313 keV) for nitrogen; 23Na(p,p‧γ)23Na (Eγ = 441 and 1636 keV) and 23Na(p,α‧γ)20Ne (Eγ = 1634 keV) for sodium; 27Al(p,p‧γ)27Al (Eγ = 844 and 1014 keV) and 27Al(p,α‧γ)24Mg (Eγ = 1369 keV) for aluminum; 28Si(p,p‧γ)28Si (Eγ = 1779 keV) and 29Si(p,p‧γ)29Si (Eγ = 1273 keV) for silicon. The PIGE thick target yields have been measured with an overall uncertainty typically better than 10%. The use of the measured thick target yield to benchmark and validate experimental cross sections available in the literature is demonstrated.

  5. Thermal formation of corundum from aluminium hydroxides prepared from various aluminium salts

    Indian Academy of Sciences (India)

    J Temuujin; Ts JADAMBAA; K J D Mackenzie; P Angerer; F Porte; F Riley

    2000-08-01

    Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived from the sulfate. This contains a higher concentration of anionic impurities related to differences in the solubility of the original aluminium salts. The sulfate is retained in the gel to higher temperatures at which its eventual decomposition may lead to the formation of a reactive pore structure which facilitates the nucleation of -Al2O3.

  6. Synthesis of aluminium nanoparticles by arc evaporation of an aluminium cathode surface

    Indian Academy of Sciences (India)

    M Gazanfari; M Karimzadeh; S Ghorbani; M R Sadeghi; G Azizi; H Karimi; N Fattahi; Z Karimzadeh

    2014-06-01

    Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on the nanoparticles was performed immediately. The effects of media on the yield and morphology of aluminium nanoparticles were investigated. Analysis result of the samples indicated that particle size was less than 30 nm, when 120 A/cm2 arc current was used. In addition, coating agent can affect arc velocity, arc stability, morphology and composition of the nanoparticles. Resultant nanoparticles were identified using X-ray powder diffraction (XRD), also their surface morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and finally the accuracy of coating was assessed with infrared (IR) spectroscopy.

  7. Cold-impregnated aluminium. A new source of nickel exposure.

    Science.gov (United States)

    Lidén, C

    1994-07-01

    A new technique for finishing anodized aluminium was introduced during the 1980s--cold impregnation with nickel. Nickel is available on the surface of cold-impregnated aluminium, as shown by the dimethylglyoxime test. Chemical analysis with EDXA showed that nickel was in the form of NiSO4. A case of work-related allergic contact dermatitis in an engraver with nickel allergy is reported. It transpired that the patient was exposed to nickel in connection with aluminium. It is concluded that cold-impregnated aluminium is a new source of nickel exposure, probably previously unknown to dermatologists. PMID:7924288

  8. Effects of aluminium surface morphology and chemical modification on wettability

    Science.gov (United States)

    Rahimi, M.; Fojan, P.; Gurevich, L.; Afshari, A.

    2014-03-01

    Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie-Baxter to Wenzel regime upon changing the surface roughness was also observed.

  9. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  10. Aluminium anode for biogalvanic metal--oxygen -cells

    Energy Technology Data Exchange (ETDEWEB)

    Weidlich, E.

    1975-02-20

    The invention deals with an aluminium anode for biogalvanic metal--oxygen cells. The object of the invention is to improve further an aluminium anode for biogalvanic metal--oxygen cells. In particular, the lifetime is to be increased and the Faraday degree of efficiency is to be improved by suppressing an excessive hydrogen development. The anode is thus constructed so as to have a metal net on both sides with aluminium layers, and the surfaces of the aluminium layers not facing the metal net are lapped or sand-blasted and have an anodized layer on their boundary regions.

  11. Negative aluminium electrode for biogalvanic metal-oxygen cells

    Energy Technology Data Exchange (ETDEWEB)

    Weidlich, E.

    1977-03-24

    The invention deals with an aluminium anode for biogalvanic metal-oxygen cells. The object of the invention is to further improve an aluminium anode for biogalvanic metal-oxygen cells. In particular, the service life is to be increased and the Faraday degree of efficiency is to be improved, by suppressing an excessive hydrogen development. The anode is thus constructed so as to have a metal net on both sides with aluminium layers and the surfaces of the aluminium layers not facing the metal net are lapped or sand-blasted and have an eloxal layer on their boundary regions.

  12. Comparison of calcium carbonate and aluminium hydroxide as phosphate binders on biochemical bone markers, PTH(1-84), and bone mineral content in dialysis patients

    DEFF Research Database (Denmark)

    Jespersen, B; Jensen, J D; Nielsen, H K;

    1991-01-01

    Bone mineral content, estimated by single-photon absorptiometry of the forearm, serum values of intact parathyroid hormone (PTH(1-84], osteocalcin, alkaline phosphatase, 1,25-dihydroxycholecalciferol (1,25(OH)2D3), and aluminium were determined during treatment with calcium carbonate (CaCO3...

  13. An arrangement for irradiating cultured mammalian cells with aluminium characteristic ultrasoft x-rays

    International Nuclear Information System (INIS)

    Ultrasoft X-rays are useful for testing the validity of mechanistic models of biological damage caused by radiation. Described here is the construction and operation of a cold-cathode transmission-target discharge tube for irradiating mammalian cells in vitro with aluminium characteristic X-rays (1.487 keV). Particular attention is given to the problems of sample preparation and dosimetry for this shallowly penetrating radiation. The proportion of contaminating bremsstrahlung radiation is measured to establish the optimum operating conditions. Preliminary data from experiments using V79 Chinese hamster cells show that aluminium characteristic X-rays are about twice as effective at inactivating the cells as 250 kVsub(P) X-rays. (author)

  14. Changes in the elasto mechanic constants of cold drawn pure aluminium

    International Nuclear Information System (INIS)

    The changes in the elastic constants at 298 K of polycrystalline samples of pure aluminium (99.5%) with different levels of cold-working have been determined. The deformation process has been carried out in a tension machine. The properties measured are: Young modulus, E, Poisson ratio, ν, and yield strength, σ0,2. The Young modulus diminishes from 70 to 63 GPa for =-2.5% deformation (elongation) and then increases with the successive cold-working passes. The Poisson ratio shows a similar behavior whereas the yield strength increases with cold-work. Pure aluminium behavior is similar to that obtained for pure iron (Armco) and for F-1140 annealed steel. (Author) 9 refs

  15. The effective thermal conductivity of insulation materials reinforced with aluminium foil at low temperatures

    Science.gov (United States)

    Yüksel, N.; Avcı, A.; Kılıç, M.

    2012-09-01

    The effective thermal conductivity (ETC) of multilayer thermal insulation materials was experimentally investigated as a function of temperature (0-25 °C). The materials consisted of binary/ternary glass wools or ternary expanded polystyrene foams reinforced with aluminium foil. The experimental measurements were performed using a guarded hot plate with temperature differences of 5, 10 and 15 °C. The results indicated that significant correlations exist between ETC and the characteristics of the materials with decreasing temperature. The ETC decreases with reinforcement with aluminium foil at the same temperature or with temperature differences of 5 and 15 °C. In addition, it was clearly observed that the ETC decreases sharply with decreased temperature. Consequently, reflective materials may reduce the ETC at low temperatures.

  16. Influence of the aluminium impregnation [ Al(NO33] in the beta zeolite over its acidity

    Directory of Open Access Journals (Sweden)

    Francisco José Sánchez Castellanos

    2010-04-01

    Full Text Available Beta zeolite was impregnated with [ Al(NO33], increasing the aluminium content in increments of 0.05% from 0.00% to 0.25%. A parallel treatment with 0.05% sulphuric acid was also performed; in both cases, methanol was used as solvent (disperse phase. Cation exchange capacity (CEC, ammonia chemisorption, infrared spectroscopy (FIT-IR, scanning electronic microscopy (SEM, X-Ray powder diffraction (XRD, atomic absorption spectroscopy (AAS, titration with sodium hydroxide and nitrogen physisorption at 77K were used to carry out the physical and chemical characterization of the catalysts. Futhermore, the catalysts were employed in the esterification of ethanol with acetic acid, to quantify the effect of aluminium impregnation over the beta zeolite.

  17. DEFORMATION BEHAVIOR OF AA6063 ALUMINIUM ALLOY AFTER REMOVING FRICTION EFFECT UNDER HOT WORKING CONDITIONS

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The hot deformation behavior of AA6063 aluminium alloy has been investigated by means of compression tests at temperatures between 400 and 520℃, and strain ratesranging from 2.5 to 10 s-1. Owing to the barreling, the theoretical model on the basis of Hill's general method is used to calculate the flow stress of a cylindrical spec-imen under uniaxial simple compression so as to consider the friction effect at the die-specimen interface. A method of evaluating the friction coefficient by combining compression tests with the finite element method is presented. The real flow behavior of AA6063 aluminium alloy can be described with sinh-Arrhenius equation. The hot deformation activation energy Q derived from the corrected stress and strain data is 232.350 k.J/mol.

  18. A study on the recycling of aluminium alloy 7075 scrap

    Energy Technology Data Exchange (ETDEWEB)

    Oezer, Goekhan [Yildiz Technical Univ., Yildiz (TR). Balkan Centre of Advanced Casting Technologies (BACAT); Marsoglu, Muezeyyen [Yildiz Technical Univ., Yildiz (Turkey). Dept. for Metal and Materials Science Engineering; Burgucu, Sarp

    2012-07-01

    Aluminium and its alloys have recently become an important metal whose area and amount of usage increase more and more, due to their mechanical properties, recycling ability, and penetrability. If it is considered that the bauxite, which is the raw material of aluminium is rare on earth, and also the area and amount of aluminium usage increases over time, the importance of aluminium recycling goes up. aluminium recycling has become crucial by means of both, the potential of the scrap's dependant increase on usage and the primary aluminium production, as it is providing energy and cost savings. 7xxx grades of scrap are collected with other scrap of aluminium alloys in one turn and recycled all together. As the regain of these alloys is not done by isolation of the various grades, the finally recycled ingots result in lower grades. High value aluminium scrap is regrettably not recovered, as it was anticipated. This study is dealing with 7075 aluminium alloys originated from discharged blow molding tools and the rest piece cuttings of blocks and plates. The material has been subjected to an induction furnace, and has been remelted into small ingots and hardened according to 7075 aluminium alloy parameters (hardening aluminium tooling). [German] Aluminium und seine Legierungen sind in den letzten Jahren aufgrund ihrer mechanischen Eigenschaften, ihrer Recyclingfaehigkeit und ihrer Durchlaessigkeit immer bedeutendere metallische Werkstoffe geworden. Unter Beruecksichtigung, dass Bauxit als Rohmaterial selten auf der Erde vorkommt und der Verbrauch mit der Zeit steigt, waechst die Bedeutung des Recyclings von Aluminium. Aluminiumrecycling, zumal es Energieund Kosteneinsparungen ermoeglicht, ist sowohl fuer die schrottabhaengigen Verwendungspotentiale und die PrimaerAluminiumproduktion gleichermassen bedeutend geworden. Die 7xxxx Schrottlegierungen werden in einem Arbeitsgang mit dem Schrott aus anderen Aluminiumlegierungen gesammelt und recycled. Da die

  19. Effects of aluminium surface morphology and chemical modification on wettability

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

    2014-03-01

    Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

  20. There is (still too much aluminium in infant formulas

    Directory of Open Access Journals (Sweden)

    Burrell Shelle-Ann M

    2010-08-01

    Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

  1. Sensibilité du haricot Phaseolus vulgaris à la concentration en aluminium des sols de la région des grands lacs

    Directory of Open Access Journals (Sweden)

    Wouters, JFR.

    1986-01-01

    Full Text Available Sensibility to soil aluminium concentration of the common bean Phaseolus vulgaris in the African "Great Lakes" region. The climate of the African region around the "Great Lakes" induces a strong process of soil weathering which eventually leads to a strong aluminium saturation of the absorption complex, as expressed by the "m" index of Kamprath. The response to aluminium toxicity of the common bean cv. Diacol Calima, a widely grown variety in Burundi, has been studied in pot trials in two ways : (1 Using superficial soil samples of "humiferous high elevation kaolisols" whose "m" index varied between 4 and 92 ; (2 On culture condition consisting of an inert substrate complemented with a nutritional solution to which a serie of soluble aluminium concentrations were added. Under soil condition, biomass produced after a period of 25 days of growth, decreased as from "m" = 33. The number of Rhizobium nodules decreased drastically with aluminium toxicity becoming negligible at "m" - 33. On culture media, rising concentration of aluminium affected growth adversely as well, although root growth inhibition was less pronounced than under soil condition.

  2. Gas heat treatment plants for the aluminium industry; Gasbeheizte Waermebehandlungsanlagen fuer die Aluminium-Industrie

    Energy Technology Data Exchange (ETDEWEB)

    Olberts, P.; Hanus, A. [LOI Thermprocess GmbH, Essen (Germany)

    2004-09-01

    LOI Thermoprocess has developed new, flexible, innovative furnace designs for heat treatment of aluminium in general (car industry) and particularly for cylinder heads, engine units, chassis components, textured components, wheels, rolled sheet and extrusions. The furnaces are heated by means of radiant tubes (recuperators) and by the more usual open gas heating system (flue gas recirculation). (orig.)

  3. The aluminium body has been promoted in Canada; La carrosserie aluminium promue au Canada

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2004-02-01

    The aluminium vehicles technology is a technology which allows, with an equivalent structure, to decrease the weight of a car of 40%. Presented by the Alcan firm, this technology is one of the technologies of the year 2003. The Alcan firm has, besides, received the 2003 technology price awarded by the magazine Industry Week. (O.M.)

  4. Combined Corrosion and Wear of Aluminium Alloy 7075-T6

    NARCIS (Netherlands)

    Liu, Y.; Mol, J.M.C.; Janssen, G.C.A.M.

    2016-01-01

    The aluminium alloy 7075-T6 is widely used in engineering. In some applications, like slurry transport, corrosion and abrasion occur simultaneously, resulting in early material failure. In the present work, we investigated the combined effect of corrosion and wear on the aluminium alloy 7075-T6. We

  5. New Policies to Control the Aluminium Industry Expansion

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>Information from China Nonferrous Metals Industry Association (CNIA) shows that new government policies on China’s aluminium industry will be released soon in order to control the rapid expansion of the aluminium industry which consumes large amount of power resources. Based on the new policies, investors of

  6. Chalco Calls for End of More Control Measures on Aluminium

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> To control the investment rush in electrolyticaluminium in recent years and ensure thehealthy development of China’s aluminium in-dustry, the State Council recently released aseries of adjustment policies and control meas-ures,which effectively prevented theinvestment rush and limited the aluminium out-put growth.

  7. Haemodialysis related osteomalacia: a staining method to demonstrate aluminium

    OpenAIRE

    Buchanan, Malcolm RC; Ihle, Benno U; Dunn, Cheryl M

    1981-01-01

    A slight modification in tissue processing and staining technique enables a previously described method for staining aluminium to be used to demonstrate aluminium in osteomalacia associated with haemodialysis. The stain appears to be accurate in diagnosing this condition and may assist in establishing the diagnosis before severe osteomalacia develops.

  8. Developments in finite element simulations of aluminium extrusion

    NARCIS (Netherlands)

    Lof, Joeri

    2000-01-01

    Aluminium extrusion is a forming process used to produce profiles. A large variety of profiles can be made by pressing a billet of hot aluminium through a hole that closely resembles the required cross-section of the profie. At the present time, design of extrusion dies and operation in extrusion co

  9. Spark counting technique with an aluminium oxide film

    International Nuclear Information System (INIS)

    Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm2. The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

  10. CAD implementation of design rules for aluminium extrusion dies

    NARCIS (Netherlands)

    Ouwerkerk, van Gijs

    2009-01-01

    Aluminium extrusion is an industrial forming process that is used to produce long profiles of a constant cross-section. This cross-section is shaped by the opening in a steel tool known as the die. The understanding of the mechanics of the aluminium extrusion process is still limited. The flow of al

  11. Enhanced corrosion protection by microstructural control of aluminium brazing sheet

    NARCIS (Netherlands)

    Norouzi Afshar, F.

    2013-01-01

    Aluminium brazing sheet is a sandwich material made out of two aluminium alloys (AA4xxx/AA3xxx) and is widely used in automotive heat exchangers. One of the main performance criteria for heat exchanger units is the lifetime of the product. The lifetime of the heat exchanger units is determined by th

  12. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  13. CERN: very large magnet with aluminium winding

    Energy Technology Data Exchange (ETDEWEB)

    Wittgenstein, F.A.

    1984-10-25

    The construction of an octagonal solenoid from trapezoidal plates of Al, 6m long and 6cm thick, assembled by electron beam welding, for installation in a laboratory 50m underground is described. The objective is to create a field of 0.5T in a volume of 1000m/sup 3/ for the L3 particle detector of the LEP accelerator project. Principal dimensions and weights of the structure are given and its three stages of implementation are described, with reference to the contributions from the Swiss aluminium industry.

  14. Friction stir welding of single crystal aluminium

    DEFF Research Database (Denmark)

    Fonda, Richard Warren; Wert, John A.; Reynolds, A.P.;

    2007-01-01

    Friction stir welds were prepared in different orientations in an aluminium single crystal. The welds were quenched to preserve the microstructure surrounding the tool and then electron backscattered diffraction was used to reveal the generation of grain boundaries and the evolution...... of crystallographic texture around the tool in each weld. The extent of both dynamic recrystallisation and conventional recrystallisation varied considerably as a function of weld orientation. As the base plate begins to interact with the deformation field surrounding the tool, regions of the single crystal rotate...

  15. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy); Gorla, Leopoldo; Nessi, Simone; Grosso, Mario [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  16. New sheet aluminium qualities for low-cost lightweight constructions; Neue Aluminium-Blechqualitaeten fuer den kosteneffizienten Leichtbau

    Energy Technology Data Exchange (ETDEWEB)

    Bloeck, M.; Furrer, P. [Novelis Technology AG, Neuhausen (Switzerland)

    2005-11-01

    Aluminium alloys used for car bodies have a wide range of material characteristics. New developments focus on selective development of material and surface characteristics for obtaining sheet aluminium qualities optimized for specific applications. These and further measures taken by Novelis are to reduce material consumption, simplify process steps in motor car manufacturing and reducing the overall system cost. (orig.)

  17. Design of the lines of aluminium drawing. Part 2; Conception des filieres de filage d'aluminium. Partie 2

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    This work is the second part of the file 'design of the lines of aluminium drawing'. It gives elements for structuring the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  18. Metal doped fluorocarbon polymer films prepared by plasma polymerization using an RF planar magnetron target

    Energy Technology Data Exchange (ETDEWEB)

    Biederman, H.; Holland, L. (Sussex Univ., Brighton (UK). Lab. for Plasma Materials Processing)

    1983-07-01

    Fluorocarbon films have been prepared by plasma polymerization of CF/sub 4/ using an RF planar magnetron with an aluminium target. More than one order of magnitude higher deposition rate has been achieved in comparison with an R.F. diode system operated under similar conditions of monomer pressure and flow rate and power input. A glow discharge in a CF/sub 4/(25%)-argon(75%) mixture was used to incorporate aluminium from a target electrode into the polymer films. The foregoing mixture and another based on CF/sub 4/(87%)-argon(13%) were used in the RF discharge with a copper target. Some experiments with a gold target and pure CF/sub 4/ as the inlet gas were also made. The film structure was examined by SEM and TEM and characteristic micrographs are presented here. The composition of the films was estimated from an EAS study. The sheet resistivity of the metal/polymer film complexes was determined.

  19. Aluminium matrix composites: Challenges and opportunities

    Indian Academy of Sciences (India)

    M K Surappa

    2003-02-01

    Aluminium matrix composites (AMCs) refer to the class of light weight high performance aluminium centric material systems. The reinforcement in AMCs could be in the form of continuous/discontinuous fibres, whisker or particulates, in volume fractions ranging from a few percent to 70%. Properties of AMCs can be tailored to the demands of different industrial applications by suitable combinations of matrix, reinforcement and processing route. Presently several grades of AMCs are manufactured by different routes. Three decades of intensive research have provided a wealth of new scientific knowledge on the intrinsic and extrinsic effects of ceramic reinforcement vis-a-vis physical, mechanical, thermo-mechanical and tribological properties of AMCs. In the last few years, AMCs have been utilised in high-tech structural and functional applications including aerospace, defence, automotive, and thermal management areas, as well as in sports and recreation. It is interesting to note that research on particle-reinforced cast AMCs took root in India during the 70’s, attained industrial maturity in the developed world and is currently in the process of joining the mainstream of materials. This paper presents an overview of AMC material systems on aspects relating to processing, microstructure, properties and applications.

  20. Reactions on carbon anodes in aluminium electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Eidet, Trygve

    1997-12-31

    The consumption of carbon anodes and energy in aluminium electrolysis is higher than what is required theoretically. This thesis studies the most important of the reactions that consume anode materials. These reactions are the electrochemical anode reaction and the airburn and carboxy reactions. The first part of the thesis deals with the kinetics and mechanism of the electrochemical anode reaction using electrochemical impedance spectroscopy. The second part deals with air and carboxy reactivity of carbon anodes and studies the effects of inorganic impurities on the reactivity of carbon anodes in the aluminium industry. Special attention is given to sulphur since its effect on the carbon gasification is not well understood. Sulphur is always present in anodes, and it is expected that the sulphur content of available anode cokes will increase in the future. It has also been suggested that sulphur poisons catalyzing impurities in the anodes. Other impurities that were investigated are iron, nickel and vanadium, which are common impurities in anodes which have been reported to catalyze carbon gasification. 88 refs., 92 figs., 24 tabs.

  1. Pemanfaatan Limbah Abu Terbang Sebagai Penguat Aluminium Matrix Composite

    Directory of Open Access Journals (Sweden)

    Subarmono Subarmono

    2008-01-01

    Full Text Available This research aims to utilize fly ash which is obtained from waste of combustion of coal in steam power plant as a reinforcement of aluminum matrix composite (AMC. The amounts of fly ash of 2.5%, 5%, 7.5% and 10% wt were added to fine aluminum powder (dimension of particles are smaller than 40 µm. Each composition was mixed using a rotary mixer for 3 hr. The mixture was uniaxially pressed and it was followed by isostatic compaction with a pressure of 100 MPa to produce green bodies. They was pressureless sintered in argon atmosphere at various temperatures of 500°C, 525°C, 550°C, 575°C and 600ºC. Bending strength, Vickers hardness, wear resistance, density of the AMC were tested, and the microstructures were observed using SEM. The results show that the mechanical properties increase with increasing the fly ash content up to 5% wt. The bending strength, hardness, porosity and wear rate are 74 MPa, 66 VHN, 4.5% and 0.04 mg/(MPa.m, respectively. Abstract in Bahasa Indonesia: Penelitian ini bertujuan untuk memanfaatkan abu terbang sebagai penguat komposit bermatrik aluminium (AMC. Abu terbang merupakan limbah pembakaran batu bara pada pembangkit listrik tenaga uap. Abu terbang sejumlah 2,5%; 5%; 7,5% dan 10% berat dicampur dengan serbuk aluminium (ukuran serbuk lebih kesil dari 40 µm. Setiap campuran diaduk menggunakan rotay mixer selama 3 jam. Campuran aluminum dan abu terbang dikompaksi secara uniaksial dilanjutkan kompaksi secara isostatik dengan tekanan 100 MPa dan diikuti sintering tanpa tekanan dengan lingkungan gas argon dan variasi temperatur 500°C, 525°C, 550°C, 575°C dan 600°C. Kekuatan bending, kekerasan Vickers, ketahanan aus dan densitas komposit diuji serta struktur mikro diamati menggunakan SEM. Hasil pengujian menunjukkan bahwa sifat mekanis meningkat seiring dengan peningkatan fraksi berat abu terbang sampai 5% berat, selebihnya terjadi penurunan. Kekuatam bending, kekerasan Vickers, porositas dan laju keausan berturut

  2. Tensile behaviour of aluminium 7017 alloy at various temperatures and strain rates

    Directory of Open Access Journals (Sweden)

    Ravindranadh Bobbili

    2016-04-01

    Full Text Available The objective of the present study is to carry out high strain rate tensile tests on 7017 aluminium alloy under different strain rates ranging from 0.01, 500, 1000 and 1500 s−1 and at temperatures of 25, 100, 200 and 300 °C. Quasi-Static tensile stress–strain curves were generated using INSTRON 8500 machine. Johnson-Cook (J-C constitutive model was developed for 7017 aluminium alloy based on high strain rate tensile data generated from split Hopkinson tension bar (SHTB at various temperatures. This study evidently showed an improvement in dynamic strength as the strain rate increases. The predictions of J-C model are observed to be in consistence with the experimental data for all strain rates and temperatures. The fracture surfaces of specimens tested were studied under SEM. The change in fracture mode has been observed at different strain rates. The shear mode of fracture is dominant at lower strain rates (0.01 and 500 s−1; whereas cup- and cone-like surface representing dimple structure is found at the higher strain rates (1000 and 1500 s−1. The numbers of dimples at high strain rates are more than the quasi-static and intermediate strain rates. It is also observed that the flow stress decreases with increase in temperature. The 7017 aluminium alloy demonstrates thermal softening at higher temperatures. So when the temperature is more than 200 °C at these strain rates, thermal softening is predominant mode of deformation mechanism. It is found that when the temperature increases to 200 °C, the number of dimples rises and the dimple size of 7017 aluminium alloy is larger than at lower temperatures.

  3. New developments on optimizing properties of high-Zn aluminium cast alloys

    Science.gov (United States)

    Krajewski, W. K.; Buras, J.; Krajewski, P. K.; Greer, A. L.; Schumacher, P.; Haberl, K.

    2016-07-01

    Foundry alloys with Al-based matrices have a wide range of uses in today's global economy and there is a high demand for castings of Al alloys, including Al-Zn alloys. In this paper, investigations on the grain refinement of high-Zn aluminium cast alloys are presented. Aluminium alloys with relatively high zinc content have a tendency to be coarse-grained, especially in the case of castings with low cooling rates such as are found in sand moulds. The coarse-grained structure degrades the plasticity, specifically the elongation. Therefore, for aluminium alloys of high (10-30 wt.%) zinc content, inoculation is attractive, aiming to break up the primary dendrites of the a-phase solid solution of zinc in aluminium. Such dendrites are the principal microstructural component in these alloys. On the other hand, a finer grain structure usually reduces the damping (e.g. as measured by attenuation of ultrasound) in these alloys. In the present investigations, a binary sand-cast Al-20 wt.% Zn alloy was inoculated with different additions of AlTi3C0.15 (TiCAl) and ZnTi-based master alloys. The sand-cast samples were subjected to mechanical-property measurements (tensile strength and elongation), image analysis to determine grain size, and measurements of the attenuation of 1 MHz ultrasound. It is found that both of the master alloys used cause significant refinement of the a-AlZn primary dendrites and change their morphology from linear-branched to semi-globular, increase the elongation by about 40%, and decrease the attenuation coefficient by about 25% in comparison with the initial alloy without inoculation.

  4. Synthesis of aluminium nanoparticles by arc plasma spray under atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Mandilas, Charalampos; Daskalos, Emmanouil [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Karagiannakis, George, E-mail: gkarag@cperi.certh.gr [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Konstandopoulos, Athanasios G., E-mail: agk@cperi.certh.gr [Aerosol and Particle Technology Laboratory (APTL), Chemical Process and Energy Resources Institute, Centre for Research and Technology-Hellas (CERTH/CPERI), P.O. Box 361, 57001 Thermi, Thessaloniki (Greece); Department of Chemical Engineering, Aristotle University, P.O. Box 1517, 54006 Thessaloniki (Greece)

    2013-01-01

    Highlights: Black-Right-Pointing-Pointer A customized arc-plasma spraying based system has been designed and implemented. Black-Right-Pointing-Pointer The system is relatively simple, robust and operates at atmospheric pressure. Black-Right-Pointing-Pointer Preparation of aluminium nanoparticles from micron-sized powder was successful. Black-Right-Pointing-Pointer Various nano-sized distributions were possible depending on operating parameters. Black-Right-Pointing-Pointer Optimization of the proposed design will lead to higher efficiencies and throughput. - Abstract: The present study addresses the feasibility to synthesize aluminium nanoparticles (NPs) from micron-sized aluminium powder with the use of a customized atmospheric plasma spraying (APS) technique. Using APS, nanoparticle synthesis can be achieved via rapid melting and vaporization of the initial micrometric particles and their subsequent re-nucleation. A custom mantle system was designed and developed with the aid of relevant simplified CFD simulations. The mantle provided the necessary inert environment (argon), at ambient pressure, in order to avoid any oxidation of the metal during plasma spraying while promoted rapid quenching of the gasified metal. The particles formed were collected with the aid of a quartz filter downstream of the plasma flame and the production rate achieved was 2 g min{sup -1}. Ex situ post-characterization of the particles via X-ray diffraction, specific surface area measurement (BET), transmission electron microscopy (TEM) coupled with energy dispersive spectrometry (EDS) and thermogravimetric analysis (TGA) under air revealed that the powders obtained primarily comprised of monocrystalline metallic aluminium nanoparticles of almost spherical shape. The NPs possessed a 2-5 nm oxide coating layer. By regulating the conditions inside the mantle, a variety of different size distributions were obtained.

  5. INTEROGATION OF THE MANUFACTURING ROUTE OF ALUMINIUM AA 1050 USED IN LITHOGRAPHIC APPLICATION

    OpenAIRE

    Witkowska, Malgorzata Danuta

    2013-01-01

    The aluminium AA1050 alloy, known as commercially pure aluminium, contains 99.5% Al, together with Fe and Si as major alloying elements. During fabrication of aluminium substrates for lithographic printing plates in Bridgnorth Aluminium Ltd, the AA 1050 aluminium alloy proceeds through various stages of thermomechanical processing, with the conditions at each processing stage influencing the microstructure of the final coil. Because of its specific gravity, tensile strength, surface performa...

  6. A 25μm pitch LWIR focal plane array with pixel-level 15-bit ADC providing high well capacity and targeting 2mK NETD

    Science.gov (United States)

    Guellec, Fabrice; Peizerat, Arnaud; Tchagaspanian, Michael; de Borniol, Eric; Bisotto, Sylvette; Mollard, Laurent; Castelein, Pierre; Zanatta, Jean-Paul; Maillart, Patrick; Zecri, Michel; Peyrard, Jean-Christophe

    2010-04-01

    CEA Leti has recently developed a new readout IC (ROIC) with pixel-level ADC for cooled infrared focal plane arrays (FPAs). It operates at 50Hz frame rate in a snapshot Integrate-While-Read (IWR) mode. It targets applications that provide a large amount of integrated charge thanks to a long integration time. The pixel-level analog-to-digital conversion is based on charge packets counting. This technique offers a large well capacity that paves the way for a breakthrough in NETD performances. The 15 bits ADC resolution preserves the excellent detector SNR at full well (3Ge-). These characteristics are essential for LWIR FPAs as broad intra-scene dynamic range imaging requires high sensitivity. The ROIC, featuring a 320x256 array with 25μm pixel pitch, has been designed in a standard 0.18μm CMOS technology. The main design challenges for this digital pixel array (SNR, power consumption and layout density) are discussed. The IC has been hybridized to a LWIR detector fabricated using our in-house HgCdTe process. The first electro-optical test results of the detector dewar assembly are presented. They validate both the pixel-level ADC concept and its circuit implementation. Finally, the benefit of this LWIR FPA in terms of NETD performance is demonstrated.

  7. Preparation of Aluminium Oxynitride by Carbothermal Reduction of Aluminium Oxide in a Flowing N2 Atmosphere

    Institute of Scientific and Technical Information of China (English)

    LIYa-wei; YUANRun-zhang; 等

    1996-01-01

    Carbothermal reduction of alumina into aluminium oxynitride(AlON) spinel in a flowing nitrogen atmosphere was studied.The effects of Al2O3/C ratio temperature,soaking time,heating rate molding pressure of samples,and nitrogen flow rate on reactions were investigated.Then the stability of AlON was elucidated and AlON wa confirmed as an intermediate compound in reduction of alumina.

  8. Aluminium: Aluminij: kovina izbire: the metal of choice:

    OpenAIRE

    Gándara, María Josefa Freiría

    2013-01-01

    This article summarizes the importance of aluminium as the metal of choice formany applications. Aluminium is a lightweight, durable metal. It is silvery in appearance when freshly cut, is a good conductor of heat and electricity, and is easily shaped by moulding and extruding. Aluminium has two main advantages when compared with other metals. Firstly, it has a low density, about one-third that of iron and copper. Secondly, although it reacts rapidly with the oxygen in air, it forms a thin, t...

  9. Optimization of Magnesium Metal into Commercially Pure Aluminium

    Directory of Open Access Journals (Sweden)

    Vandana J Rao

    2014-02-01

    Full Text Available The present investigation, involve development of Al-Mg systems by addition of magnesium into commercially pure aluminium. The amounts of magnesium added into commercially pure aluminium are of 1 and 2 wt%. The recoveries of magnesium are around 85-90%.Remaining Mg react with oxygen and float on the liquid aluminium. Presence of magnesium creates two phenomena. One is solid solution hardening and other is intermetallics formation. Both the phenomena checked by microstructural changes and by measuring the electrical conductivity values. By increasing the Mg, content mechanical properties (hardness and tensile strength increases and electrical conductivity decreases.

  10. Effect of pressurized steam on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

    2012-01-01

    Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

  11. Effect of filtration on reoxidation proceses in aluminium alloys

    Directory of Open Access Journals (Sweden)

    D. Bolibruchova

    2010-01-01

    Full Text Available This article is focused on reoxidation processes during filtration of aluminium alloys. Many of our experimental works pointed out, that using filtration media placed in gating system causes reoxidation of poured aluminium alloy. Main aim of our latest work was to validate our arguments, that filter in gating system can be considered as obstacle for continuous pouring, with help of computer simulations. This article is only a small part of our researches focused on reoxidation processes during filtration of aluminium alloys.

  12. Corrosion issues of powder coated AA6060 aluminium profiles

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl;

    2015-01-01

    In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

  13. Thickness Evaluation of Aluminium Plate Using Pulsed Eddy Current Technique

    Science.gov (United States)

    Singh, Gurpartap; Bapat, Harsh Madhukar; Singh, Bhanu Pratap; Bandyopadhyay, Manojit; Puri, Rakesh Kumar; Badodkar, Deepak Narayanrao

    2013-10-01

    This paper describes a pulsed eddy current (PEC) based non-destructive testing system used for detection of thickness variation in aluminium plate. A giant magneto-resistive sensor has been used instead of pick up coil for detecting resultant magnetic field. The PEC response signals obtained from 1 to 5 mm thickness change in aluminium plate were investigated. Two time domain features, namely peak value and time to peak, of PEC response were used for extracting information about thickness variation in aluminium plate. The variation of peak value and time to peak with thickness was compared. A program was developed to display the thickness variation of the tested sample.

  14. Radiation-induced creep of copper, aluminium and their alloys

    International Nuclear Information System (INIS)

    The results of creep studies on copper, aluminium and their alloys with and without neutron irradiation are presented. The experiments are carried out at the WWR-K reactor at the neutron fluence of 1.4.1016 n/m2.s (2.5.1016 n/m2.s, E>0.1 MeV). Polycrystalline copper (99.99 and 99.95%), aluminium (99.99%) and the alloys of copper with 4 at% of titanium, of aluminium with 4.2% of copper are studied within the temperature interval 0.31-0.51 Tm. (orig.)

  15. Study of fatigue behaviour of 7475 aluminium alloy

    Indian Academy of Sciences (India)

    B B Verma; J D Atkinson; M Kumar

    2001-04-01

    Fatigue properties of a thermomechanically treated 7475 aluminium alloy have been studied in the present investigation. The alloy exhibited superior fatigue life compared to conventional structural aluminium alloys and comparable stage II crack growth rate. It was also noticed that the fatigue crack initiated from a surface grain and the crack extension was dominated by ductile striations. Analysis also revealed that this alloy possessed fracture toughness and tensile properties superior to that noticed with other structural aluminium alloys. Therefore the use of this alloy can safely reduce the overall weight of the aircraft.

  16. Aluminium content of some foods and food products in the USA, with aluminium food additives.

    Science.gov (United States)

    Saiyed, Salim M; Yokel, Robert A

    2005-03-01

    The primary objective was to determine the aluminium (Al) content of selected foods and food products in the USA which contain Al as an approved food additive. Intake of Al from the labeled serving size of each food product was calculated. The samples were acid or base digested and analysed for Al using electrothermal atomic absorption spectrometry. Quality control (QC) samples, with matrices matching the samples, were generated and used to verify the Al determinations. Food product Al content ranged from Cheese in a serving of frozen pizzas had up to 14 mg of Al, from basic sodium aluminium phosphate; whereas the same amount of cheese in a ready-to-eat restaurant pizza provided 0.03-0.09 mg. Many single serving packets of non-dairy creamer had approximately 50-600 mg Al kg(-1) as sodium aluminosilicate, providing up to 1.5 mg Al per serving. Many single serving packets of salt also had sodium aluminosilicate as an additive, but the Al content was less than in single-serving non-dairy creamer packets. Acidic sodium aluminium phosphate was present in many food products, pancakes and waffles. Baking powder, some pancake/waffle mixes and frozen products, and ready-to-eat pancakes provided the most Al of the foods tested; up to 180 mg/serving. Many products provide a significant amount of Al compared to the typical intake of 3-12 mg/day reported from dietary Al studies conducted in many countries. PMID:16019791

  17. Studies of medium scale non-axisymmetric aluminium missile impacts

    International Nuclear Information System (INIS)

    VTT Technical Research Centre of Finland has studied medium scale missile impacts against rigid and deformable targets to provide data for the calibration and verification of numerical models of a loading scenario where an aircraft impacts against a nuclear power plant. The testing apparatus provides data for validating these models. Missiles used in most of the tests have been cylindrical aluminium and steel pipes. Recent development in the project is tests with a more structurally complex airplane-like missile. Aircraft fuel is also represented as water. The objective of these tests is to produce an impact loading transient with a changing loading area resembling full scale aircraft impact. The tests are also used to develop and verify models of impact scenarios. The goal is to predict the results of the experiments using a mathematical model and if successful, apply the same methods to other impact scenarios. The assumption is made that if the experimental tests can be simulated with accuracy, the same methodology can be applied to full scale phenomenon

  18. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    Directory of Open Access Journals (Sweden)

    Ma D.

    2013-01-01

    Full Text Available Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC, a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate was used to adjust pH value and the basicity of the pickle liquor, the PAFC was subsequently prepared after the polymerization process. The optimal synthesizing parameters for the preparation of PAFC obtained were as follows: the concentration of hydrochloric acid of 24 wt%, ratio of hydrochloric acid to bauxite tailings of 6:1, temperature of 90ºC, leaching time of 2.5 hours, ration of pickle liquor to calcium aluminate of 12:1, polymerization temperature of 90ºC and polymerization time of about 3 hours. The basicity of PAFC was higher than 68%, the sum concentration of Al2O3 and Fe2O3 was beyond 12.5%. The results of flocculation tests indicate that the PAFC has a better performance of removing the turbidity of wastewater compared to PAC, and PAFC prepared by bauxite tailings is a kind of high quality flocculants.

  19. Adsorption of aluminium by stream particulates.

    Science.gov (United States)

    Tipping, E; Ohnstad, M; Woof, C

    1989-01-01

    An experimental study was made of the adsorption of aluminium by fine particulates from Whitray Beck, a hill stream in NW England. Adsorption increased with Al(3) activity, pH and concentration of particles, and could be quantitatively described by the empirical equation: [Formula: see text] [particles] where square brackets indicate concentrations, curly brackets, activities, and alpha, beta and gamma are constants with values of 5.14x10(-10) (mol litre(-1))(2.015) (g particles litre(-1))(-1), 0.457, and 1.472, respectively. For the experimental data, the equation gave a correlation ratio of 0.99. The equation accounts reasonably well for the adsorption of Al by particulates from seven other streams. In applying the equation, it must be borne in mind that the desorption kinetics of Al depend on pH, and rapid reversibility (or=10%) of total monomeric Al. PMID:15092454

  20. Mechanical behaviour of aluminium-lithium alloys

    Indian Academy of Sciences (India)

    N Eswara Prasad; A A Gokhale; P Rama Rao

    2003-02-01

    Aluminium-lithium alloys hold promise of providing a breakthrough response to the crying need for lightweight alloys for use as structurals in aerospace applications. Considerable worldwide research has gone into developing a range of these alloys over the last three decades. As a result, substantial understanding has been developed of the microstructure-based micromechanisms of strengthening, of fatigue and fracture as well as of anisotropy in mechanical properties. However, these alloys have not yet greatly displaced the conventionally used denser Al alloys on account of their poorer ductility, fracture toughness and low cycle fatigue resistance. This review aims to summarise the work pertaining to study of structure and mechanical properties with a view to indicate the directions that have been and can be pursued to overcome property limitations.

  1. Stopping power of aluminium for 5-12 MeV protons and deuterons

    DEFF Research Database (Denmark)

    Andersen, H.H.; Garfinkel, A.F.; Hanke, C.C.;

    1966-01-01

    The stopping power of aluminium for 5-12 MeV protons and deuterons has been measured by a thermometric compensation technique working at liquid helium temperature. The experimental method is described and the standard deviation of the results is found to be 0.3%. In order to obtain this accuracy...... one has to apply theoretical corrections for the influence of Coulomb scattering, X-rays and deltarays. Other possible corrections are discussed, but are found to be negligible for this combination of projectiles, energies and target material. The results agree with published experimental results...

  2. Property enhancement by grain refinement of zinc-aluminium foundry alloys

    Science.gov (United States)

    Krajewski, W. K.; Greer, A. L.; Piwowarski, G.; Krajewski, P. K.

    2016-03-01

    Development of cast alloys with good mechanical properties and involving less energy consumption during their melting is one of the key demands of today's industry. Zinc foundry alloys of high and medium Al content, i.e. Zn-(15-30) wt.% Al and Zn-(8-12) wt.% Al, can satisfy these requirements. The present paper summarizes the work [1-9] on improving properties of sand-cast ZnAl10 (Zn-10 wt.% Al) and ZnAl25 (Zn-25 wt. % Al) alloys by melt inoculation. Special attention was devoted to improving ductility, whilst preserving high damping properties at the same time. The composition and structural modification of medium- and high-aluminium zinc alloys influence their strength, tribological properties and structural stability. In a series of studies, Zn - (10-12) wt. % Al and Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The melted alloys were inoculated with ZnTi-based refiners and it was observed that the dendritic structure is significantly finer already after addition of 50 - 100 ppm Ti to the melted alloys. The alloy's structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), dilatometry, pin-on-disc wear, and tensile strength measurements. Grain refinement leads to significant improvement of ductility in the binary high-aluminium Zn-(25-27) Al alloys while in the medium-aluminium alloys the effect is rather weak. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties. Furthermore, the high initial damping properties were nearly entirely preserved after inoculation. The results obtained allow us to characterize grain refinement of the examined high-aluminium zinc alloys as a promising process leading to the improvement of their properties. At the same time, using low melting ZnTi-based master alloys makes it possible to avoid the excessive melt overheating

  3. Dissolved aluminium in the ocean conveyor of the West Atlantic Ocean : Effects of the biological cycle, scavenging, sediment resuspension and hydrography

    NARCIS (Netherlands)

    Middag, R.; van Hulten, M. M. P.; Van Aken, H. M.; Rijkenberg, M. J. A.; Gerringa, L. J. A.; Laan, P.; de Baar, H. J. W.

    2015-01-01

    The concentrations of dissolved aluminium (dissolved Al) were studied along the West Atlantic GEOTRACES GA02 transect from 64 degrees N to 50 degrees S. Concentrations ranged from similar to 0.5 nmol kg(-1) in the high latitude surface waters to similar to 48 nmol kg(-1) in surface waters around 25

  4. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud.

  5. COMPARATION BETWEEN NONDESTRUCTIVE TESTING METHODS FOR THE ALUMINIUM BRAZED PIECES

    Directory of Open Access Journals (Sweden)

    Dan NIŢOI

    2014-05-01

    Full Text Available Presented paper refers to different control methods used in aluminium brazed joining because of possible defects. Low joining complexity permits exact damages position in relation with materials geometry.

  6. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. PMID:26365318

  7. Deposition of aluminium nanoparticles using dense plasma focus device

    International Nuclear Information System (INIS)

    Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

  8. Aluminium dynamics and proton buttering in undistributed samples of acidified forest soils; Aluminium-Dynamik und Protonenpufferung in ungestoerten Proben versauerter Waldboeden

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, E.

    1992-12-31

    In this work non-displaced soil samples were used to test the reaction of acidified forest soils in the aluminium buffering range to different proton concentrations. The examined quantities were the proton buffering rate in the macropore spaces and the correlated rate of aluminium release. Furthermore, the types of aluminium bondage occuring in the soil solution and their influence on the aluminium dynamics within the profile were determined. The significance of species distribution for the interpretation of the toxic potential of aluminium is illuminated. The influence of soil structure on proton buffering, aluminium release and species distribution is described from a global viewpoint. (orig.) [Deutsch] In der vorliegenden Arbeit wird an natuerlich gelagerten Bodenproben die Reaktion versauerter Waldboeden im Aluminium-Pufferbereich auf unterschiedlich starke Protonenbelastungen untersucht. Dabei interessiert die Rate der Protonenpufferung im Makroporenraum einhergehend mit der Menge freigesetzten Aluminiums. Darueberhinaus wird untersucht, welche Aluminium-Bindungsformen in der Bodenloesung vorliegen und welchen Einfluss diese auf die Aluminium-Dynamik innerhalb des Profils haben. Die Bedeutung der Speziesverteilung fuer die Interpretation potentieller Aluminium-Toxizitaet wird beleuchtet. Uebergreifend wird der Einfluss der Bodenstruktur auf Protonenpufferung, Aluminium-Freisetzung sowie Speziesverteilung herausgestellt. (orig.)

  9. China’s Export of Fabricated Aluminium Keeps Rising

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>Affected by the State macro economic adjustment policies, China’s export of primary aluminium has decreased obviously. However, China’s export of fabricated aluminum is increasing rapidly, which has led to the investment rush of the aluminium industry, leading to the serious concern by the government. Market rumors are spreading that the government will soon adjust the export tax rebate rates so as to curb such a trend.

  10. Modeling of aluminium deposition from chloroaluminate ionic liquids

    OpenAIRE

    Schaltin, Stijn; Ganapathi, Murugan; Binnemans, Koen; Fransaer, Jan

    2011-01-01

    A finite-element model of the electrodeposition of aluminium from chloroaluminate ionic liquids is introduced. The purpose of this model is to give an explanation for the reasonable current densities that can be achieved in chloroaluminate ionic liquids despite the fact that the electrochemically active Al2Cl7- complexes are transformed into inactive AlCl4- complexes during the electrodeposition of aluminium. The obtainable current density in the electrodeposition from chloroaluminate ionic l...

  11. Metal-Ceramic Interfaces in Laser Coated Aluminium Alloys

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1994-01-01

    A novel process was developed to firmly coat an aluminium alloy, Al6061, with α-Al2O3 by means of laser processing. In this approach a mixture of SiO2 and Al powder was used to inject in the laser melted surface of aluminium. A reaction product α-Al2O3 layer of a thickness of 100 µm was created whic

  12. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    OpenAIRE

    Hamilta de Oliveira Santos; Marilene Morelli Serna; Nelson Batista de Lima; Isolda Costa; Jesualdo Luiz Rossi

    2005-01-01

    Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken f...

  13. Local electrochemical behaviour of 7xxx aluminium alloys

    OpenAIRE

    F. Andreatta

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a negative effect on safety and costs. This PhD thesis investigates the relation between electrochemical behaviour and microstructure of a number of 7xxx aluminium alloys: AA7075, AA7349 and an experime...

  14. Crushing modes of aluminium tubes under axial compression

    OpenAIRE

    Pled, Florent; Yan, Wenyi; Wen, Cui'e

    2014-01-01

    6 pages International audience A numerical study of the crushing of circular aluminium tubes with and without aluminium foam fillers has been carried out to investigate their buckling behaviours under axial compression. A crushing mode classification chart has been established for empty tubes. The influence of boundary conditions on crushing mode has also been investigated. The effect of foam filler on the crushing mode of tubes filled with foam was then examined. The predicted results ...

  15. Melting and solidification of bismuth inclusions in aluminium

    DEFF Research Database (Denmark)

    Thoft, N.B.; Bohr, J.; Buras, B.;

    1995-01-01

    Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different experime......Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different...

  16. Geometry Effects at Atomic-Size Aluminium Contacts

    OpenAIRE

    Schwingenschloegl, Udo; Schuster, Cosima

    2007-01-01

    We present electronic structure calculations for aluminium nanocontacts. Addressing the neck of the contact, we compare characteristic geometries to investigate the effects of the local aluminium coordination on the electronic states. We find that the Al 3pz states are very sensitive against modifications of the orbital overlap, which has serious consequences for the transport properties. Stretching of the contact shifts states towards the Fermi energy, leaving the system instable against fer...

  17. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Ivan Michalec

    2013-01-01

    Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  18. Blast Loaded Aluminium Plates : Experiments and numerical simulations

    OpenAIRE

    Melby, Emil Arne; Eide, Hilde Olaug Stakvik

    2013-01-01

    Light and flexible protective constructions in aluminium could be subjected to a blast load. In this thesis the effect of blast loading on aluminium plates of the type 1050A ? H14 was studied through experiments and numerical simulations. The effect of fragmentation was idealized with predrilled holes. The thesis was written at the Structural Impact Laboratory (SIMLab) at NTNU in collaboration with the Norwegian Defence Estates Agency (NDEA).Tensile tests revealed a clearly anisotropic behavi...

  19. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    OpenAIRE

    Napachat Tareelap; Kaysinee Sriraksasin; Nakorn Srisukhumbowornchai; Swieng Thuanboon; Choochat Nitipanyawong

    2014-01-01

    Due to the failure of manganese aluminium bronze (MAB) propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium...

  20. Lake restoration with aluminium, bentonite and Phoslock: the effect on sediment stability and light attenuation

    DEFF Research Database (Denmark)

    Egemose, Sara; Reitzel, Kasper; Flindt, Mogens

    treatments on aluminium mobility, sediment stability or light climate. A laboratory flume experiment including three shallow Danish lakes was conducted. We measured the effects of aluminium, Phoslock (a commercial product), bentonite, and a combination of bentonite/aluminium. Each treatment caused a varying...... consolidation of the sediment. The largest consolidation occurred using Phoslock- and bentonite-addition followed by bentonite/aluminium-addition, whereas aluminium alone had no effect. Sediment stability thresholds were measured before and after addition. Especially Phoslock, but also bentonite and bentonite....../aluminium increased sediment erosion threshold, with respectively 200%, 43% and 57%. Aluminium, bentonite/aluminium, and Phoslock improved the light conditions in the water phase, with respectively 60%, 57% and 50%, whereas bentonite created higher turbidity. Conclusively aluminium improved the light conditions...

  1. Bremsstrahlung spectra produced by kilovolt electron impact on thick targets

    International Nuclear Information System (INIS)

    Measurements of bremsstrahlung spectra generated by 5-25 keV electron impact on thick targets of aluminium, titanium, zirconium, molybdenum and tungsten are reported. The experimental data are compared with the simulation results of X-ray spectra obtained from the general-purpose Monte Carlo code PENELOPE, which implements accurate cross-sections for ordinary bremsstrahlung emission but disregards polarization bremsstrahlung. The agreement between the experimental and simulation results is satisfactory. This is in contrast with a recent study in which large discrepancies were observed between experimental and Monte Carlo simulation results. Our results provide evidence for the reliability of the combined choices of the interaction cross-sections and of the simulation algorithms implemented in PENELOPE for bremsstrahlung emission.

  2. The binding, transport and fate of aluminium in biological cells.

    Science.gov (United States)

    Exley, Christopher; Mold, Matthew J

    2015-04-01

    Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion.

  3. Assessment of trace aluminium content in parenteral solutions by combined cloud point preconcentration-flow injection inductively coupled plasma optical emission spectrometry.

    Science.gov (United States)

    Sombra, Lorena L; Luconi, Marta O; Fernández, Liliana P; Olsina, Roberto A; Silva, María F; Martínez, Luis D

    2003-01-01

    A micelle-mediated phase separation without added chelating agents to preconcentrate trace levels of aluminium in parenteral solutions as a prior step to its determination by flow injection inductively coupled plasma optical emission spectrometry has been developed. The enrichment step is based on the cloud point extraction of aluminium with the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5). The chemical variables affecting the sensitivity of the extractive-spectrometric procedure were studied in detail. After optimization, a preconcentration factor of 200 and a %E higher than 99.9 were achieved. The detection limit (DL) value of aluminium for the preconcentration of 50 ml of parenteral solution was 0.25 microgl(-1). The calibration graph using the preconcentration system for aluminium was linear with a correlation coefficient of 0.9997 at levels near the DLs up to at least 200 microgl(-1). The developed hyphenated assay, which thoroughly satisfies the typical requirements for pharmaceutical control processes, is appropriate to monitor the aluminium concentration in parenteral nutrition.

  4. Range parameters of aluminium implants in medium and heavy mass metals

    Science.gov (United States)

    Hayes, M.; Hauser, T.; Friedland, E.; Thugwane, S. J.; Malherbe, J. B.; Naidoo, S. R.

    2000-03-01

    Nuclear reaction analysis was used to determine the range profiles of 150 keV aluminium ions implanted into a variety of metal targets in the atomic number region of 23⩽Z 2⩽78 . Implantations were performed at room temperature with fluences of 5×10 16 Al + cm -2 and dose rates below 10 13 Al + cm -2 s -1 to prevent excessive target heating. Profiles were determined by detecting the 10.76 MeV photons from the 27Al(p,γ) 28Si resonance reaction at 992 keV as a function of proton energy. Range profiles were extracted from the excitation curve after correcting for proton straggling. The experimental profiles and range moments are compared with TRIM predictions, taking target sputtering effects into account.

  5. China Rescinds the Export Tax on Aluminium Alloys Made by Scrap

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>According to an official from the Tax Regulations Office under China’s State Council, from July 1st 2005, China will rescind the 5 per cent export tax on the aluminium alloys produced by using aluminium alloys scrap. An official from the State Council’s office said that through investigation they found that most aluminium alloys produced from aluminium scrap are not that energy consuming compared to primary aluminium. Starting from January 1st 2005, China decided to collect 5 per cent export tax on aluminium so as to control the industry development connected with high energy cost.

  6. Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

    Directory of Open Access Journals (Sweden)

    Senze Magdalena

    2015-03-01

    Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

  7. Formation and Characterization of Ceramic Nanocomposite Crystalline Coatings on Aluminium by Anodization

    Institute of Scientific and Technical Information of China (English)

    M.Mubarak Ali; V.Raj

    2013-01-01

    Ceramic nanocomposite coatings have been synthesized on aluminium by using lithium sulphate electrolyte with zirconium silicate additive by anodization.The effects of current density (CD) on microhardness,structure,composition and surface topography of the oxide layer formed at various CDs (0.1-0.25 A/cm2) have been studied.Crystalline coatings formed at 0.25 A/cm2 have been (width 95 nm) observed with a relatively uniform distribution confirmed by scanning electron microscopy.Additionally,the average microhardness value of ceramic nanocomposite coatings fabricated from lithium sulphate-zirconium silicate bath is approximately 8.5 times higher than that of the as-received aluminium.The surface statistics of the coatings is discussed in detail to explain the roughness and related parameters for better understanding.These observations demonstrate the importance of surface statistics in controlling the morphology of the coatings and its properties.From the X-ray diffraction investigations,it can be concluded that the formed nanocomposite coatings are crystalline in nature and that the crystallinity of the coatings decreases with increasing applied current density.

  8. Acute aluminium phosphide poisoning, what is new?

    Directory of Open Access Journals (Sweden)

    Yatendra Singh

    2014-01-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide that is commonly used for grain preservation. AlP has currently generated interest with increasing number of cases in the past four decades because of its increased use for agricultural and nonagricultural purposes, and also its easy availability in the markets has led to its increased misuse to commit suicide. Ingestion is usually suicidal in intent, uncommonly accidental and rarely homicidal. The poison affects all systems, shock, cardiac arrhythmias with varied ECG changes and gastrointestinal features being the most prominent. Diagnosis is made on the basis of clinical suspicion, a positive silver nitrate paper test to phosphine, and gastric aspirate and viscera biochemistry. Treatment includes early gastric lavage with potassium permanganate or a combination of coconut oil and sodium bicarbonate, administration of charcoal and palliative care. Specific therapy includes intravenous magnesium sulphate and oral coconut oil. Unfortunately, the lack of a specific antidote Results in very high mortality and the key to treatment lies in rapid decontamination and institution of resuscitative measures. This article aims to identify the salient features and mechanism of AlP poisoning along with its management strategies and prognostic variables.

  9. Low cost aluminium metal matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Withers, G.

    2007-03-15

    Low cost, light weight Ultalite{reg_sign} is an Aluminium Metal Matrix Composite (AL-MMC) which utilises wear resistant ceramic particles derived from flyash. Ultalite AL-MMC typically contains between 10 and 30 per cent ceramic particles, and is formulated for the manufacture of wear resistant automotive components. Due to its low density and ease of processing into net shape die casting, Ultalite AL-MMC provides weight savings of up to 60 per cent over components fabricated from cast iron, thereby providing improved fuel efficiency with reduced greenhouse emissions. The original flyash material was sourced from a black coal power station in Queensland, where it contained a wide range of particles sizes. To narrow the size range and to remove impurities, a proprietary pretreatment developed by Dr Thomas Robl and co-researchers at the University of Kentucky was employed. The University of Kentucky developed the technology for the classification and benefaction of flyash to produce high-grade Pozzolan, which is used in Portland Cement product. This technology is now being applied to the production of Ultalite AL-MMC. Testing performed by Dr Robl has shown that the proprietary technology can eliminate the hollow particles, extract detrimental carbon-based impurities and remove the extremely fine and coarse particles. All that remains are dense ceramic particles with an average particle size of approximately 30 {mu}m. 9 refs., 3 figs.

  10. Eu(III)-doped aluminium yttrium oxide

    International Nuclear Information System (INIS)

    In this work, we report the synthesis and the photoluminescence features of Eu(III)-doped yttrium-aluminium oxide obtained by non-hydrolytic sol-gel routes. After heating the powders above 600 deg C the XRD patterns show the presence of the Y4Al2O9 (YAM) and Y3Al5O12 (YAG) phases. At 800 and at 1500 deg C the PL spectra display the Eu(III) lines characteristic of the YAM monoclinic phase. The 5D0→7F2 transition is favored relatively to the 5D0→7F1 lines. However, at 1100 deg C the cubic YAG is the preferential phase and the 5D0→7F1 transition dominates the spectrum. The Eu(III) ions lie in a centro symmetrical site. The different solvents used in the sol-gel synthesis also change the relative proportion between these two phases. This is monitored analyzing the modifications in the relative intensity between the 5D0→7F2 and the 5D0→7F1 transitions. (author)

  11. Role of phytohormones in aluminium rhizotoxicity.

    Science.gov (United States)

    Kopittke, Peter M

    2016-10-01

    Elevated concentrations of soluble aluminium (Al) reduce root growth in acid soils, but much remains unknown regarding the toxicity of this Al as well as the mechanisms by which plants respond. This review examines changes in phytohormones in Al-stressed plants. Al often results in a rapid 'burst' of ethylene in root apical tissues within 15-30 min, with this regulating an increase in auxin. This production of ethylene and auxin seems to be a component of a plant-response to toxic Al, resulting in cell wall modification or regulation of organic acid release. There is also evidence of a role of auxin in the expression of Al toxicity itself, with Al decreasing basipetal transport of auxin, thereby potentially decreasing wall loosening as required for elongation. Increasingly, changes in abscisic acid in root apices also seem to be involved in plant-responses to toxic Al. Changes in cytokinins, gibberellins and jasmonates following exposure to Al are also examined, although little information is available. Finally, although not a phytohormone, concentrations of nitric oxide change rapidly in Al-exposed tissues. The information presented in this review will assist in focusing future research efforts in examining the importance of phytohormones in plant tissues exposed to toxic levels of Al. PMID:27352002

  12. Fuzzy Multicriteria Ranking of Aluminium Coating Methods

    Science.gov (United States)

    Batzias, A. F.

    2007-12-01

    This work deals with multicriteria ranking of aluminium coating methods. The alternatives used are: sulfuric acid anodization, A1; oxalic acid anodization, A2; chromic acid anodization, A3; phosphoric acid anodization, A4; integral color anodizing, A5; chemical conversion coating, A6; electrostatic powder deposition, A7. The criteria used are: cost of production, f1; environmental friendliness of production process, f2; appearance (texture), f3; reflectivity, f4; response to coloring, f5; corrosion resistance, f6; abrasion resistance, f7; fatigue resistance, f8. Five experts coming from relevant industrial units set grades to the criteria vector and the preference matrix according to a properly modified Delphi method. Sensitivity analysis of the ranked first alternative A1 against the `second best', which was A3 at low and A7 at high resolution levels proved that the solution is robust. The dependence of anodized products quality on upstream processes is presented and the impact of energy price increase on industrial cost is discussed.

  13. Anomalous Diffusion of Mo Implanted into Aluminium

    Institute of Scientific and Technical Information of China (English)

    张通和; 吴瑜光; 邓志威; 钱卫东

    2001-01-01

    Mo ions are implanted into aluminium with a high ion flux and high dose at elevated temperatures of 300℃, 400℃ and 500℃ . X-ray diffraction spectra show that the Al12Mo phases are formed. Rutherford backscattering spectroscopy indicates that a profile of Mo appears in Al around the depth of 550nm and with an atomic concentration of ~7%, when Mo is implanted to the dose of 3 × 1017/cm2 with an ion flux of 45μA/cm2 (400℃).If the dose increases to 1 × 1018/cm2 at the same ion flux, the penetration of Mo ions in Al can reach a depth of 2μm, which is greater than the ion project range Rp (52.5nm). The results show that anomalous diffusion takes place. Owing to the intense atom collision cascades, the diffusion coefficient increases greatly with the increase of the ion flux and dose. The Mo diffusion coefficients in Al are calculated. The Mo retained dose in A1 increases obviously with the increase of the ion flux.

  14. Effect of friction time on the properties of friction welded YSZ‐alumina composite and 6061 aluminium alloy

    Directory of Open Access Journals (Sweden)

    Uday M. Basheer

    2012-03-01

    Full Text Available The aim of this work was to study the effect of friction time on the microstructure and mechanical properties of alumina 0, 25, 50 wt% yttria stabilized zirconia (YSZ composite and 6061 aluminium alloy joints formed by friction welding. The alumina-YSZ composites were prepared through slip casting in plaster of Paris molds (POP and subsequently sintered at 1600°C, while the aluminium rods were machined down using a lathe machine to the dimension required. The welding process was carried out under different rotational speeds and friction times, while friction force (0.5 ton-force was kept constant. Scanning electron microscopy was used to characterize the interface of the joints structure. The experimental results showed that the friction time has a significant effect on joint structure and mechanical properties.

  15. Modeling and Simulating Material Behavior during Hot Blank - Cold Die (HB-CD) Stamping of Aluminium Alloy Sheets

    Science.gov (United States)

    Zhang, Nan; Abu-Farha, Fadi

    2016-08-01

    Hot blank - cold die (HB-CD) stamping, non-isothermal hot stamping, of aluminium alloy sheets offers great opportunities for high production rates at low cost, while overcoming limited material formability issues. Yet developing an accurate model that can describe the complex material behavior over the wide ranging conditions of HB-CD stamping (temperatures ranging between 25 and 350 °C) is challenging. Moreover, validation of the developed models under transient conditions is problematic. This work presents he results of a comprehensive characterization, material modeling, FE simulation and experimental validation effort to capture the behavior of an aluminium alloy sheet during HB-CD stamping. In particular, we highlight the integration between temperature measurements (thermography) and strain measurements (digital image correlation) for the accurate validation of model predictions of non-isothermal material deformation.

  16. Aluminium Matrix Composites Reinforced with Co-continuous Interlaced Phases Aluminium-alumina Needles

    Directory of Open Access Journals (Sweden)

    Elvio de Napole Gregolin

    2002-09-01

    Full Text Available An Al-5SiO2 (5 wt% of SiO2 aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si/Al2O3 interlaced structure named co-continuous composite. A technique of powder metallurgy, using commercial aluminium powder and the silica fibers as starting materials, followed by hot extrusion, was used to produce the composite. The co-continuous microstructure was obtained partially or totally on the fibers as a result of the reaction, which occurs during the heat treatment, first by solid diffusion and finally by the liquid Al-Si in local equilibrium, formed with the silicon released by reaction. The internal structure of the fibers was characterized using field emission electron microscope (FEG-SEM and optical microscopy on polished and fractured samples.

  17. Fabrication experience of aluminium clad aluminium matrix dispersion fuels at BARC

    International Nuclear Information System (INIS)

    Aluminium clad, aluminium matrix plate type dispersion fuels have been fabricated in BARC in recent years as part of fuel development programme for small non-power research reactors. The present paper describes the flowsheet developed for fabrication of Al-UAlx, Al-U3Si2 and Al-U3O8 fuels at BARC. The Al-20% U alloy fuel for KAMINI neutron radiography reactor was prepared by 'melting and casting' route, followed by picture framing and roll-bonding. For higher 'U' density fuels namely, Al-UAlx, Al-U3O8 and Al-U3Si2 the 'powder metallurgy' route was followed for preparation of fuel meat. The novel features in fabrication route were: addition of Zr for stabilizing UAl3 phase in Al-20% U alloy; x-ray radiography and microdensitometric scanning of radiographs for location of fuel outline inside fuel element and for confirming homogeneous distribution of fissile atoms; immersion ultrasonic testing for confirming good bonding between mating Al surface of the fuel plate. (author)

  18. The General Situation of the Scale and Layout of Aluminium Industry in China

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>Since 2002, aluminium industry has become a key industry under the macro control of the country, for which the reason is the aluminium industry in China has seen "repeated construc-tion", "blind investment", "excessive capacity",

  19. PREDICTION OF PLASTIC ANISOTROPY IN ALUMINIUM EXTRUDED TUBES BY FINITE ELEMENT POLYCRYSTAL MODEL

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Numerical simulation of extrusion process of aluminium tube is dealt with using the finite element polycrystal model. The non-uniformity in plastic anisotropies of aluminium extruded tubes through the wall thickness is investigated.

  20. Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process

    Science.gov (United States)

    Asmara, Y. P.; Siregar, J. P.; Tezara, C.; Ann, Chang Tai

    2016-02-01

    Aluminium is one of the preferred materials to be used as sacrificial anode for carbon steel protection. The efficiency of these can be low due to the formation of oxide layer which passivate the anodes. Currently, to improve its efficiency, there are efforts using a new technique called surface modifications. The objective of this research is to study corrosion mechanism of aluminium sacrificial anode which has been processed by cold work. The cold works are applied by reducing the thickness of aluminium sacrificial anodes at 20% and 40% of thickness reduction. The cathodic protection experiments were performed by immersion of aluminium connected to carbon steel cylinder in 3% NaCl solutions. Visual inspections using SEM had been conducted during the experiments and corrosion rate data were taken in every week for 8 weeks of immersion time. Corrosion rate data were measured using weight loss and linear polarization technique (LPR). From the results, it is observed that cold worked aluminium sacrificial anode have a better corrosion performance. It shows higher corrosion rate and lower corrosion potential. The anodes also provided a long functional for sacrificial anode before it stop working. From SEM investigation, it is shown that cold works have changed the microstructure of anodes which is suspected in increasing corrosion rate and cause de-passivate of the surface anodes.

  1. Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

    Directory of Open Access Journals (Sweden)

    Mathivanan Periasamy

    2012-06-01

    Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

  2. Acute oral toxicity and biodistribution study of zinc-aluminium-levodopa nanocomposite

    Science.gov (United States)

    Kura, Aminu Umar; Saifullah, Bullo; Cheah, Pike-See; Hussein, Mohd Zobir; Azmi, Norazrina; Fakurazi, Sharida

    2015-03-01

    Layered double hydroxide (LDH) is an inorganic-organic nano-layered material that harbours drug between its two-layered sheets, forming a sandwich-like structure. It is attracting a great deal of attention as an alternative drug delivery (nanodelivery) system in the field of pharmacology due to their relative low toxic potential. The production of these nanodelivery systems, aimed at improving human health through decrease toxicity, targeted delivery of the active compound to areas of interest with sustained release ability. In this study, we administered zinc-aluminium-LDH-levodopa nanocomposite (ZAL) and zinc-aluminium nanocomposite (ZA) to Sprague Dawley rats to evaluate for acute oral toxicity following OECD guidelines. The oral administration of ZAL and ZA at a limit dose of 2,000 mg/kg produced neither mortality nor acute toxic signs throughout 14 days of the observation. The percentage of body weight gain of the animals showed no significant difference between control and treatment groups. Animal from the two treated groups gained weight continuously over the study period, which was shown to be significantly higher than the weight at the beginning of the study ( P animal serum showed no significant difference between rats treated with ZAL, ZA and controls. There was no gross lesion or histopathological changes observed in vital organs of the rats. The results suggested that ZAL and ZA at 2,000 mg/kg body weight in rats do not induce acute toxicity in the animals. Elemental analysis of tissues of treated animals demonstrated the wider distribution of the nanocomposite including the brain. In summary, findings of acute toxicity tests in this study suggest that zinc-aluminium nanocomposite intercalated with and the un-intercalated were safe when administered orally in animal models for short periods of time. It also highlighted the potential distribution ability of Tween-80 coated nanocomposite after oral administration.

  3. Development and characterization of ultra-thin dosemeters of aluminium oxide

    International Nuclear Information System (INIS)

    The aim of the present thesis work has been to investigate the thermoluminescent (Tl) response of aluminium oxide thin films with thicknesses of the order of 300 nm prepared by laser ablation. Aluminium oxide thin films show Tl response after they are subject to ultraviolet, beta and gamma radiation. The Tl curves exhibit peaks around 75 C and 169 C for UV radiation, 112 C and 180 C for beta particles and 110 C and 176 C for gamma radiation. In order to improve the Tl response some growth parameters such as power density and distance target-substrate were varied. The relation dose-response shows a non-linear behavior for UV irradiation; a linear behavior for beta-particles dose from 150 mGy to 50 Gy, and a linear behavior for gamma radiation dose from 5 Gy to 100 Gy. The kinetic Tl parameters were determined by Computerized Glow Curve Deconvolution (CGCD) method as well as using analytical methods. The CGCD results show that the high temperature peak is composed by four peaks with maximums in 165.7, 188.1, 215.3, 246.5 C. These obey a second order kinetics. The trap depth (E) values are 1.4, 1.6, 1.8 and 2.0 eV respectively. The different analytical results show a trap depth values of 0.914, 0.82 and 0.656 eV respectively. Oxide aluminium thin films obtained would be a suitable tool owing to their potential applications in clinical dosimetry, in the dose distributions due to weekly penetrating radiation determination, and in interfaces dosimetry. (Author)

  4. Prediction of flow stress of 7017 aluminium alloy under high strain rate compression at elevated temperatures

    Directory of Open Access Journals (Sweden)

    Ravindranadh Bobbili

    2015-03-01

    Full Text Available An artificial neural network (ANN constitutive model and Johnson–Cook (J–C model were developed for 7017 aluminium alloy based on high strain rate data generated from split Hopkinson pressure bar (SHPB experiments at various temperatures. A neural network configuration consists of both training and validation, which is effectively employed to predict flow stress. Temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on Johnson–Cook (J–C model and neural network model was performed. It was observed that the developed neural network model could predict flow stress under various strain rates and temperatures. The experimental stress–strain data obtained from high strain rate compression tests using SHPB over a range of temperatures (25°–300 °C, strains (0.05–0.3 and strain rates (1500–4500 s−1 were employed to formulate J–C model to predict the flow stress behaviour of 7017 aluminium alloy under high strain rate loading. The J–C model and the back-propagation ANN model were developed to predict the flow stress of 7017 aluminium alloy under high strain rates, and their predictability was evaluated in terms of correlation coefficient (R and average absolute relative error (AARE. R and AARE for the J-C model are found to be 0.8461 and 10.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. The predictions of ANN model are observed to be in consistent with the experimental data for all strain rates and temperatures.

  5. Prediction of flow stress of 7017 aluminium alloy under high strain rate compression at elevated temperatures

    Institute of Scientific and Technical Information of China (English)

    Ravindranadh BOBBILI; B. RAMAKRISHNA; V. MADHU; A.K. GOGIA

    2015-01-01

    An artificial neural network (ANN) constitutive model and JohnsoneCook (JeC) model were developed for 7017 aluminium alloy based on high strain rate data generated from split Hopkinson pressure bar (SHPB) experiments at various temperatures. A neural network configuration consists of both training and validation, which is effectively employed to predict flow stress. Temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on JohnsoneCook (JeC) model and neural network model was performed. It was observed that the developed neural network model could predict flow stress under various strain rates and tem-peratures. The experimental stressestrain data obtained from high strain rate compression tests using SHPB over a range of temperatures (25?e300 ?C), strains (0.05e0.3) and strain rates (1500e4500 s?1) were employed to formulate JeC model to predict the flow stress behaviour of 7017 aluminium alloy under high strain rate loading. The JeC model and the back-propagation ANN model were developed to predict the flow stress of 7017 aluminium alloy under high strain rates, and their predictability was evaluated in terms of correlation coefficient (R) and average absolute relative error (AARE). R and AARE for the J-C model are found to be 0.8461 and 10.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. The predictions of ANN model are observed to be in consistent with the experimental data for all strain rates and temperatures.

  6. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    OpenAIRE

    Polus Łukasz; Szumigała Maciej

    2015-01-01

    In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally f...

  7. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    OpenAIRE

    Zauzi, N. S. Ahmad; M. Z. H. Zakaria; Baini, R.; Rahman, M. R.; N. Mohamed Sutan; Hamdan, S

    2016-01-01

    Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH) on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipita...

  8. The determination of boron in high-purity aluminium metal by spark-source mass spectrometry

    International Nuclear Information System (INIS)

    A method is described for the determination of boron in high-purity aluminium metal. Both isotopic boron lines (10B+1 and 11B+1) are used for the analysis. As there are no low-abundance isotopic lines for aluminium, measurements were made direct without reference to aluminium as an internal standard. The boron concentration values of eight aluminium samples analysed by this method compared favourably with results obtained from other techniques

  9. Low Speed Laser Welding of Aluminium Alloys Using Single-Mode Fiber Lasers

    OpenAIRE

    Tu, Jay; Paleocrassas, Alexander

    2010-01-01

    In this chapter, topics related to extending fiber laser welding of aluminium in the low speed range were discussed. General topics, such as the properties of aluminium and welding defects, review of high speed laser welding of aluminium, and fiber laser characteristics and optical setups for safety, were first reviewed. Recent research results on the modelling and validation of laser welding of aluminium, experimental characterization of low speed welding processes, and the instability pheno...

  10. On adsorption of aluminium and methyl groups on silica for TMA/H2O process in atomic layer deposition of aluminium oxide nano layers

    Indian Academy of Sciences (India)

    Anu Philip; K Rajeev Kumar

    2010-04-01

    A detailed chemisorption mechanism is proposed for the atomic layer deposition (ALD) of aluminium oxide nano layers using trimethyl aluminum (TMA) and water as precursors. Six possible chemisorption mechanisms, complete ligand exchange, partial ligand exchange, simple dissociation, complete dissociation via ligand exchange, complete dissociation and association, are proposed and related parameters like ligand to metal ratio (L/M), concentrations of metal atoms and methyl groups adsorbed are calculated and compared against reported values. The maximum number of methyl groups that can get attached on the surface is calculated in a different way which yields a more realistic value of 6.25 per nm2 substrate area. The dependence of the number of metal atoms adsorbed on OH concentration is explained clearly. It is proposed that a combination of complete ligand exchange and complete dissociation is the most probable chemisorption mechanism taking place at various OH concentrations.

  11. 1,25-Dihydroxyvitamin D Promotes Negative Feedback Regulation of Toll-Like Receptor Signaling via Targeting MicroRNA-155-SOCS1 in Macrophages

    OpenAIRE

    Chen, Yunzi; Liu, Weicheng; Sun, Tao; Huang, Yong; Wang, Youli; Deb, Dilip K; Yoon, Dosuk; Kong, Juan; Thadhani, Ravi; Li, Yan Chun

    2013-01-01

    The negative feedback mechanism is essential to maintain effective immunity and tissue homeostasis. 1,25-dihydroxyvitamin D (1,25(OH)2D3) modulates innate immune response, but the mechanism remains poorly understood. Here we report that vitamin D receptor (VDR) signaling attenuates Toll-like receptor-mediated inflammation by enhancing the negative feedback inhibition. VDR inactivation leads to hyper inflammatory response in mice and macrophage cultures when challenged with lipopolysaccharide ...

  12. Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

    Science.gov (United States)

    Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

    2011-11-01

    The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling. PMID:21274747

  13. A novel technique for the deposition of aluminium-doped zinc oxide films

    International Nuclear Information System (INIS)

    Aluminium-doped zinc oxide is used in many applications as a transparent conductive oxide coating. Such coatings are often deposited by DC reactive sputtering of metallic targets, or RF sputtering of ceramic targets. Both of these techniques have their limitations. In the DC case, alloy targets are expensive and only allow a single composition per target. Additionally, in the RF case, targets produced by hot-pressing, or sintering may have a tendency to crack unless sputtered at low powers, thus restricting the deposition rate. However, sputtering from blended powder targets offers a potential solution to all of these problems. In this project, therefore, a series of Al-doped ZnO films have been produced by the pulsed DC magnetron sputtering of blended ZnO/Al2O3 powder targets. Initial results, presented here, indicate that high quality, defect-free films can be produced with suitable electrical and optical properties. The crystallinity of the films has been examined by X-ray diffraction, before and after annealing in controlled atmospheres. A thorough investigation of glass substrate cleaning techniques has also been carried out, with the effectiveness of each technique being assessed in terms of the coating-to-substrate adhesion, as measured by the scratch testing method

  14. Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

    NARCIS (Netherlands)

    Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

    2012-01-01

    Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide p

  15. The Prospect of China’s Alumin-ium Extrusion Product Market

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>China’s aluminium extrusion industry can be dated back to the 1950s-70s,when the North- east 101 Plant was established in 1956,the Northwest Aluminium and Southwest Alumin- ium were completed and put into operation in 1968-1969.The three plants’ extrusion assem- bly lines were designed to produce aluminium

  16. The Net Exporting Trends Remains for China’s Aluminium Products

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The oversupply of China’s raw aluminium has caused the continuing net exporting for China’s aluminium products.As the situation is wors- ened due to the growing raw aluminium pro- duction and curbed demand,it is estimated that the continuation of net exporting of China’s

  17. Bakable aluminium vacuum chamber and bellows with an aluminum flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber and bellows (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the assemblies of the vacuum chambers in proton synchrotrons and electron storage rings

  18. Energy efficiency improvement and GHG abatement in the global production of primary aluminium

    NARCIS (Netherlands)

    Kermeli, Katerina; Ter Weer, Peter Hans; Crijns - Graus, Wina; Worrell, Ernst

    2015-01-01

    Primary aluminium production is a highly energy-intensive and greenhouse gas (GHG)-emitting process responsible for about 1 % of global GHG emissions. In 2009, the two most energy-intensive processes in primary aluminium production, alumina refining and aluminium smelting consumed 3.1 EJ, of which 2

  19. Determination of ultratrace amounts of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization/ICP-MS

    International Nuclear Information System (INIS)

    A method has been developed for determining the 0.01 ng g-1 level of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization (ETV)/ICP-MS. This method was found to be significantly interfered with any matrices or other elements contained. An ion-exchange technique was therefore applied to separate uranium and thorium from aluminium and other elements. It was known that uranium are adsorbed on an anion-exchange resin and thorium are adsorbed on cation-exchange resin. However, aluminium and copper were eluted with 6 M hydrochloric acid. Dissolve the sample with hydrochloric acid containing copper which was added for analysis of pure aluminium, and oxidize with hydrogen peroxide. Concentration of hydrochloric acid in the solution was adjusted to 6 M, and then passed the solution through the mixed ion-exchange resin column. After the uranium and thorium were eluted with 1 M hydrofluoric acid-0.1 M hydrochloric acid, the solution was evaporated to dryness. It was then dissolved with 1 M hydrochloric acid. Uranium and thorium were analyzed by ETV/ICP-MS using tungsten and molybdenum boats, respectively, since the tungsten boat contained high-level thorium and the molybdenum boat contained uranium. The determination limit of uranium and thorium were 0.003 and 0.005 ng g-1, respectively. (author)

  20. PEMBINAAN PENGERAJIN BOKOR ALUMINIUM DI DESA MENYALI

    Directory of Open Access Journals (Sweden)

    I NYOMAN GDE ANTARA, dkk.

    2014-04-01

    Full Text Available Alluminium bowl craft industrial center is located in Menyali village Sawan district Buleleng regency of Bali province. In this business development, they faced some problems such as increasingly expensive alluminium plate raw materials, decreasing selling product prices due to competition among craftsmen, difficulty in extending the marketing, lack of capital, lack of knowledge in business management, and lack of technical capacity and production innovation. Currently the organization has been formed aluminum bowl craftsmen groups, they are “Sumber Urip” and “Sumur Jaya”. This organization is still limited to tradisional associations such as a community organization, has not led to organize in a micro-enterprise or cooperation. Their organization management should not be arranged. Therefore, they need helps from the government and other institutions to build this bowl craftsmen in developing their businesses through a group of micro-enterprises or cooperations. Wishly, with formal business entity that would facilitate access to a variety of coaching and help governments andother institutions. From the SWOT analysis, it is found some problems and solutions that should be done. Alluminium bowl craftsmen groups, named “Sumber Urip” and “Sumur Jaya” is not in the form of business entity or cooperation yet, so that the results of coaching have agreed to form a cooperation. Venture capital assistance for the development and production are still needed and to be an absolute given, but a way to market more absolute yield is given, through participation in various events exhibition to introduce the product is expected to expandits market share up to overseas or exports. In the production process it has been introduced that is appropriate technology for instant a rolling tool to make a wiring groove on the outside of the bowl, so that it will simplify and speed up the process, especially by aged mothers.Keywords: aluminium bowl, Menyali

  1. Aluminium supplier selection for the automotive parts manufacturer

    Directory of Open Access Journals (Sweden)

    M. Cieśla

    2016-04-01

    Full Text Available This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method and a graphical method. Choosing the best offer and prioritizing suppliers allows not only the most rational decision in the field of supply logistics to be taken but also the quality of service in the metallurgical industry to be improved.

  2. [Photophysical properties and photodynamic activity of nanostructured aluminium phthalocyanines].

    Science.gov (United States)

    Udartseva, O O; Lobanov, A V; Andeeva, E R; Dmitrieva, G S; Mel'nikov, M Ia; Buravkova, L B

    2014-01-01

    We developed water-soluble supramolecular complexes of aluminium phthalocyanine based on mesoporous silica nanoparticles and polyvinylpirrolidone containing rare photoactive nanoaggregates. Radiative lifetimes, extinction coefficients and energy of electronic transitions of isolated and associated metal phthalocyanine complexes were calculated. Nontoxic concentrations of synthesized nanocomposite photosensibilizers were in vitro determined. In present study we compared photodynamic treatment efficacy using different modifications of aluminium phthalocyanine (Photosens®, AlPc-nSiO2 and AlPc-PVP). Mesenchymal stromal cells were used as a model for photodynamic treatment. Intracellular accumulation of aluminium phthalocyanine based on mesoporous silica nanoparticles AlPc-nSiO2 was the most efficient. Illumination of phthalocyanine-loaded cells led to reactive oxygen species generation and subsequent apoptotic cell death. Silica nanoparticles provided a significant decrease of effective phthalocyanine concentration and enhanced cytotoxicity of photodynamic treatment.

  3. Reflection of infrared radiation from thin aluminium layers

    CERN Document Server

    Calatroni, Sergio

    2001-01-01

    The thermal shielding of the LHC magnets cryostats will make use of Multi-Layer Insulation. This is a sandwich of several Mylar (polyester) foils 6 µm thick coated with a thin film of aluminium, having a thickness of some 30 nm. The thickness of the aluminium film must be kept at a minimum to minimise lateral thermal conduction. The outer layer of this sandwich stays at a temperature of 20 K or below, and receives IR radiation from surfaces at 77 K (wavelength of 37.6 µm at the peak of blackbody radiation), which should be reflected with the highest efficiency. The minimum thickness for the aluminium layer to avoid transmission of the radiation can be calculated by making use of the skin effect theory, taking into account the changes in electrical properties that are due to the extremely low thickness of the film.

  4. Langmuir-Blodgett Films from Schiff Base Aluminium ( Ⅲ ) Complex

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The characteristics of the LB films of Schiff base aluminium( Ⅲ ), tris(2-hydroxy-5-nitro N-dodecyl-benzylideneaminato) aluminium ( Ⅲ ) [Al (TA 12) 3], were studied. The surface pres sure-area(r-A) isotherm of Al(TA12)3 in the pure water subphase was investigated. The molec ular area, 0.48 nm2, is one-third of the expected value that indicates the formation of an aggre gate. The Langmuir-Blodgett (LB) films of Al(TA12) 3 were transferred and characterized. The UV-Vis spectra and the AFM image both confirmed that the J-aggregates formed. The polarized UV-Vis spectra indicated that the complex plane had to be oriented with an angle of about 30° to the substrate surface. The IR spectra suggested that the complexation took place between aluminium ions and the oxygen atoms of the ligand rather than the nitrogen atom.

  5. Aluminium toxicity in the rat liver and brain

    International Nuclear Information System (INIS)

    To investigate the etiology of Alzheimer's disease, we examined the brain and liver tissue uptake of aluminium 5-75 days after aluminium injection into healthy rats. Ten days after the last injection, Al was detected in the brain and the brain cell nuclei by particle-induced X-ray emission (PIXE) analysis. Al was also demonstrated in the liver and the liver cell nuclei by PIXE analysis and electron energy loss spectrometry (EELS). The morphological changes of the rat brain examined 75 days after the injection were similar to those which have been reportedly observed in the brain of patients with Alzheimer's disease. These results support the theory that Alzheimer's disease is caused by irreversible accumulation of aluminium in the brain, as well as the nuclei of brain cells. (orig.)

  6. Characterisation of Ga-coated and Ga-brazed aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Ferchaud, E. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Christien, F., E-mail: frederic.christien@univ-nantes.fr [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Barnier, V. [Ecole Nationale Superieure des Mines, MPI, CNRS UMR5146, Centre SMS, 158 Cours Fauriel, 42023 Saint Etienne (France); Paillard, P. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France)

    2012-05-15

    This work is devoted to the brazing of aluminium using liquid gallium. Gallium was deposited on aluminium samples at {approx} 50 Degree-Sign C using a liquid gallium 'polishing' technique. Brazing was undertaken for 30 min at 500 Degree-Sign C in air. EDS (Energy Dispersive X-ray Spectroscopy) and AES (Auger Electron Spectroscopy) characterisation of Ga-coated samples has shown that the Ga surface layer thickness is of ten (or a few tens of) nanometres. Furthermore, aluminium oxide layer (Al{sub 2}O{sub 3}) was shown to be 'descaled' during Ga deposition, which ensures good conditions for further brazing. Cross-section examination of Ga-coated samples shows that liquid gallium penetrates into the aluminium grain boundaries during deposition. The thickness of the grain boundary gallium film was measured using an original EDS technique and is found to be of a few tens of nanometres. The depth of gallium grain boundary penetration is about 300 {mu}m at the deposition temperature. The fracture stress of the brazed joints was measured from tensile tests and was determined to be 33 MPa. Cross-section examination of brazed joints shows that gallium has fully dissolved into the bulk and that the joint is really autogenous. - Highlights: Black-Right-Pointing-Pointer Aluminium can be brazed using liquid gallium deposited by a 'polishing' technique. Black-Right-Pointing-Pointer The aluminium oxide layer is 'descaled' during liquid Ga 'polishing' deposition. Black-Right-Pointing-Pointer EDS can be used for determination of surface and grain boundary Ga film thickness. Black-Right-Pointing-Pointer The surface and grain boundary Ga film thickness is of a few tens of nm. Black-Right-Pointing-Pointer Surface and grain boundary gallium dissolves in the bulk during brazing.

  7. Washery tailings from coal preparation used as aluminium feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Kuehn, L.; Schieder, T.; Belsky, M.; Lotze, J.; Winkhaus, G.

    1982-06-01

    Kaolinite clays and washery tailings of coal mines are the major feedstocks of the West German aluminium industry. Statistics are given in order to assess the amount of washery tailings available and their suitability as feedstocks for aluminium production. The chemical and mineralogical composition are similar for washery tailings from different mines; accordingly, also their behaviour regarding decomposition by acids will be almost identical. Al/sub 2/O/sub 3/ extraction yields are satisfactory with strongly precalcinated material using concentrated sulphuric acid or azeotropic hydrochloric acid - in the latter case, however, only if fluoride is added to the acid.

  8. Aging of maraging steel welds during aluminium alloy die casting

    OpenAIRE

    Klobčar, Damjan; Pleterski, Matej; Taljat, Boštjan; Kosec, Ladislav; Tušek, Janez

    2015-01-01

    The aim of this study is to evaluate precipitation annealing of 18% Ni maraging steel repair welds during aluminium die casting and to predict the prolonged in-service tool life. The emphasis of this study is the influence ofpost-weld precipitation annealing heat treatment and aluminium die casting thermal cycling on metallurgical and mechanical properties. A series of specimens of 1.2344 tool steel is prepared to which 1.6356 maraging steel is GTA weld cladded. Analysis of weld microstructur...

  9. Finite size melting of spherical solid-liquid aluminium interfaces

    DEFF Research Database (Denmark)

    Chang, J.; Johnson, Erik; Sakai, T.;

    2009-01-01

    We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting...... to the conclusion that the depressed melting temperature is not controlled solely by the inverse radius 1/R. Instead, we found a direct relation between the depressed melting temperature and the ratio between the solid-liquid interface area and the molten volume....

  10. Aluminium Price Looks Down Due To Increased Capacities

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>Speaking at a recent forum on China’S alumin- ium industry,Wen Xianjun,director of the aluminium branch under China Nonferrous Metals Industry Association,said that the alu- minium price in 2007 looks going downward due to the production capacity expansion out of the high market price last year.He estimates that the downward development of the alumin- ium price in China will be more obvious than that in the rest part of the world.He predicts that in 2007 the average aluminium price in

  11. Power quality results in energy efficient aluminium smelter operation

    Energy Technology Data Exchange (ETDEWEB)

    Wiestner, Max

    2010-09-15

    New aluminium smelters consume up to 2400MW of electrical energy making the energy efficiency aspect most important. Power quality, optimised power conversion systems and well engineered power plant interfaces are essential for highest energy efficiency. An early optimisation of the power system design will reduce the capital investment cost for the power plant and smelter substation as well as results in most energy efficient aluminium production. This paper describes and intends to discuss the power quality improvement concepts and designs as well as energy cost reduction opportunities which a high power quality system can achieve.

  12. The hydrolysis of aluminium, a mass spectrometric study

    OpenAIRE

    Sarpola, A.

    2007-01-01

    Abstract This thesis is focused on the hydrolysis of aluminium, the polymerisation of the hydrolysis products, and how these can be monitored by mass spectrometric methods. The main aim of this research is to figure out how the aqueous speciation of aluminium changes as a function of pH (3.2–10), concentration (1–100 mM), reaction time (1s–14d), and counter anion (Cl-, SO42-, HCOO-). The method used was electrospray mass spectrometry. The results showed more variable speciation than those ...

  13. Research of Properties of Sprayed Coatings on the Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    Raimonda Lukauskaitė

    2014-02-01

    Full Text Available In article the cathodic cleaning processes of aluminum alloyAW 5754 and cleaned substrate surface coating by plasmawith Ni-Cr-Fe-Si powder were researched. Aluminium substrateroughness after cathodic treatment at different cathodic treatmentparameters was established during the experiments. During theinvestigation a comparison of the calculated medium power1.6 to 9 kW plasma torch voltage-current characteristics withthe experimental results was made. The optimized parametersof aluminium cathode substrate cleaning process were selected;porosity and morphology of plasma sprayed nickel-based coatingwere determined.

  14. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    Directory of Open Access Journals (Sweden)

    Napachat Tareelap

    2014-03-01

    Full Text Available Due to the failure of manganese aluminium bronze (MAB propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium in seawater to form calcium carbonate film protecting the propeller from corrosion.

  15. Structure analysis of aluminium silicon manganese nitride precipitates formed in grain-oriented electrical steels

    Energy Technology Data Exchange (ETDEWEB)

    Bernier, Nicolas, E-mail: n.bernier@yahoo.fr [OCAS N.V., ArcelorMittal Global R and D Gent, Pres. J.F. Kennedylaan 3, 9060 Zelzate (Belgium); Xhoffer, Chris [OCAS N.V., ArcelorMittal Global R and D Gent, Pres. J.F. Kennedylaan 3, 9060 Zelzate (Belgium); Van De Putte, Tom, E-mail: tom.vandeputte@arcelormittal.com [OCAS N.V., ArcelorMittal Global R and D Gent, Pres. J.F. Kennedylaan 3, 9060 Zelzate (Belgium); Galceran, Montserrat [Université Libre de Bruxelles, 4MAT (Materials Engineering, Characterization, Synthesis and Recycling), Avenue F.D. Roosevelt 50, 1050 Brussels (Belgium); CIC Energigune, Albert Einstein 48, 01510 Miñano (Álava) (Spain); Godet, Stéphane [Université Libre de Bruxelles, 4MAT (Materials Engineering, Characterization, Synthesis and Recycling), Avenue F.D. Roosevelt 50, 1050 Brussels (Belgium)

    2013-12-15

    We report a detailed structural and chemical characterisation of aluminium silicon manganese nitrides that act as grain growth inhibitors in industrially processed grain-oriented (GO) electrical steels. The compounds are characterised using energy dispersive X-ray spectrometry (EDX) and energy filtered transmission electron microscopy (EFTEM), while their crystal structures are analysed using X-ray diffraction (XRD) and TEM in electron diffraction (ED), dark-field, high-resolution and automated crystallographic orientation mapping (ACOM) modes. The chemical bonding character is determined using electron energy loss spectroscopy (EELS). Despite the wide variation in composition, all the precipitates exhibit a hexagonal close-packed (h.c.p.) crystal structure and lattice parameters of aluminium nitride. The EDX measurement of ∼ 900 stoichiometrically different precipitates indicates intermediate structures between pure aluminium nitride and pure silicon manganese nitride, with a constant Si/Mn atomic ratio of ∼ 4. It is demonstrated that aluminium and silicon are interchangeably precipitated with the same local arrangement, while both Mn{sup 2+} and Mn{sup 3+} are incorporated in the h.c.p. silicon nitride interstitial sites. The oxidation of the silicon manganese nitrides most likely originates from the incorporation of oxygen during the decarburisation annealing process, thus creating extended planar defects such as stacking faults and inversion domain boundaries. The chemical composition of the inhibitors may be written as (AlN){sub x}(SiMn{sub 0.25}N{sub y}O{sub z}){sub 1−x} with x ranging from 0 to 1. - Highlights: • We study the structure of (Al,Si,Mn)N inhibitors in grain oriented electrical steels. • Inhibitors have the hexagonal close-packed symmetry with lattice parameters of AlN. • Inhibitors are intermediate structures between pure AlN and (Si,Mn)N with Si/Mn ∼ 4. • Al and Si share the same local arrangement; Mn is incorporated in both Mn

  16. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    International Nuclear Information System (INIS)

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg (AlMg3) and Al-1.1%Mg-0.5%Si (Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-1000C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) showed a complete absence of voids or bubbles in the grain interiors of the aluminium and the aluminium-alloys. Bubbles were clearly visible by TEM at grain boundaries in pure Al and the AlMg3 alloy; but bubbles were not visible in the Al6061 alloy. The bubble density in the AlMg3 alloy was considerably higher than in pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure. (orig.)

  17. Accumulation of Aluminium and Physiological Status of Tree Foliage in the Vicinity of a Large Aluminium Smelter

    Directory of Open Access Journals (Sweden)

    E. D. Wannaz

    2012-01-01

    Full Text Available A pollution gradient was observed in tree foliage sampled in the vicinity of a large aluminium production facility in Patagonia (Argentina. Leaves of Eucalyptus rostrata, and Populus hybridus and different needle ages of Pinus spec. were collected and concentrations of aluminium (Al and sulphur (S as well as physiological parameters (chlorophyll and lipid oxidation products were analyzed. Al and S concentrations indicate a steep pollution gradient in the study showing a relationship with the physiological parameters in particular membrane lipid oxidation products. The present study confirms that aluminium smelting results in high Al and sulphur deposition in the study area, and therefore further studies should be carried out taking into account potentially adverse effects of these compounds on human and ecosystem health.

  18. Carbon treated commercial aluminium alloys as anodes for aluminium-air batteries in sodium chloride electrolyte

    Science.gov (United States)

    Pino, M.; Herranz, D.; Chacón, J.; Fatás, E.; Ocón, P.

    2016-09-01

    An easy treatment based in carbon layer deposition into aluminium alloys is presented to enhance the performance of Al-air primary batteries with neutral pH electrolyte. The jellification of aluminate in the anode surface is described and avoided by the carbon covering. Treated commercial Al alloys namely Al1085 and Al7475 are tested as anodes achieving specific capacities above 1.2 Ah g-1vs 0.5 Ah g-1 without carbon covering. The influence of the binder proportion in the treatment as well as different carbonaceous materials, Carbon Black, Graphene and Pyrolytic Graphite are evaluated as candidates for the covering. Current densities of 1-10 mA cm-2 are measured and the influence of the alloy explored. A final battery design of 4 cells in series is presented for discharges with a voltage plateau of 2 V and 1 Wh g-1 energy density.

  19. Mould Filling Ability Characterisation of Cast Aluminium Alloys Using Design of Experiments

    Directory of Open Access Journals (Sweden)

    Samavedam Santhi

    2012-01-01

    Full Text Available Mould filling ability characteristic has been influencing the liquid metal flow, heat transfer, and solidification there by affecting the quality of aerospace castings. Mould filling is a critical parameter in the production of sound and quality castings, especially in the case of complex-shaped castings where section thickness is varying considerably. The mould filling ability of aluminium alloys LM6 and LM25 has been studied in the present investigation. Experimentation has been carried out using orthogonal array experimental layout. The process parameters studied in the present investigation are alloy composition, sand fineness, mould coating, and pouring temperature. The mould filling ability of selected aluminium alloy has been studied using pin test piece with cylindrical cores. The results from experimentation are analyzed to find the influence of the process parameters on mould filling ability. Based on the above, LM6 alloy has been found to have better mould filling ability characteristics and the analysis of variance has also revealed the same optimum factor combination.

  20. Investigation on the Mechanical and Tribological Properties of Aluminium-Tin Based Plain Bearing Material

    Directory of Open Access Journals (Sweden)

    T. Rameshkumar

    2010-06-01

    Full Text Available The purpose of this study is to investigate the Mechanical and Tribological properties of plain bearing alloys used especially in internal combustion engines. The mechanical properties namely Tensile strength and Hardness were investigated according to standard procedure. The sliding friction and wear properties of aluminium-tin alloy against high carbon high chromium steel were investigated at different normal loads as (29.43 N, 33.35 N and 36.25 N. Tests were carried in oil lubricated conditions with a sliding speed of 1 m/s. Prior to experimentation, the circulating engine oil 20w40 was heated to temperature of 800C using heater. The frictional behavior and wear property of aluminium-tin alloy were studied by means of pin-on-disk tribometer. The weight loss of the specimen was measured and wear and friction characteristics were calculated with respect to time, depth of wear track, sliding speed and bearing load. To determine the wear mechanism, the worn surfaces of the samples were examined using Scanning Electron Microscope (SEM. The optimum wear reduction was obtained at different normal loads and at same sliding speed.

  1. Influence of Nanowire Diameter on Structural and Optical Properties of cu Nanowire Synthesized in Anodic Aluminium Oxide Film

    Science.gov (United States)

    Cetinel, A.; Özcelik, Z.

    2016-11-01

    Copper (Cu) nanowire arrays embedded in anodic aluminium oxide films (AAO) on aluminium substrate have been synthesized by alternating current electrochemical deposition. Two-step anodization process has been performed to get the through-hole AAO with ordered nanochannels in 0.3M oxalic acids at DC voltages 30, 40, 50 and 60V, respectively. Structural characterization of the Cu nanowires has been analyzed by scanning electron microscopy (SEM) and X-ray diffraction (or) X-ray diffractometer (XRD). Our SEM analysis has revealed that the diameters of vertically oriented Cu nanowires are 15, 25, 45 and 60nm and the length of Cu nanowires having high packing density is about 15μm. XRD measurement has indicated that polycrystalline Cu nanowires prefer growth orientation along the (111) direction. Optical measurements show that reflection of the Cu nanowires/AAO on aluminium reduces with decreasing diameter of the Cu nanowires. This effect can be associated with increased light scattering from metal nanoparticles near their localized plasmon resonance frequency depending on the size and shape of the nanoparticles.

  2. Determination of cadmium, aluminium, and copper in beer and products used in its manufacture by electrothermal atomic absorption spectrometry.

    Science.gov (United States)

    Viñas, Pilar; Aguinaga, Nerea; López-García, Ignacio; Hernandez-Córdoba, Manuel

    2002-01-01

    Procedures were developed for determining cadmium, aluminium, and copper in beer and the products used in its manufacture by electrothermal atomic absorption spectrometry. Beer samples were injected into the furnace and solid samples were introduced as suspensions after preparation in a medium containing hydrogen peroxide, nitric acid, and ammonium dihydrogen phosphate for cadmium atomization. Calibration was performed with aqueous standards, and characteristic masses and detection limits were, respectively, 1 and 0.3 pg for cadmium, 18 and 5.4 pg for aluminium, and 5.6 and 6.8 pg for copper. Different samples of beer, wort, brewer's yeast, malt, raw grain, and hops were analyzed by the proposed procedures. Cadmium was found in low concentrations (0.001-0.08 microg/g and 0-1.3 ng/mL); copper (3-13 microg/g and 25-137 ng/mL) and aluminium (0.6-9 microg/g and 0.1-2 microg/mL) were found at higher levels. The reliability of the procedure was confirmed by comparing the results obtained with others based on microwave oven sample digestion, and by analyzing several certified reference materials. PMID:12083268

  3. New Investment Rush Brings up Concern for China’s Aluminium Industry

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> Although the blind construction of the electro-lytic aluminium industry has been restricted inChina this year,an investment rush in aluminaand aluminium processing has started,whichhas brought up new concern for the industry.Whether this will follow the route of the much-heated electrolytic aluminium industry remainsa question to be answered.According to someindustry analysts,under the pressure of themacro control measures of the State on theelectrolytic aluminium industry expansion,some producers of aluminium have shiftedtheir interests to the upper and lower fields soas to raise their competitiveness over the mar-

  4. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    Science.gov (United States)

    Polus, Łukasz; Szumigała, Maciej

    2015-03-01

    In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  5. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    Directory of Open Access Journals (Sweden)

    Polus Łukasz

    2015-03-01

    Full Text Available In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  6. 1,25-Dihydroxyvitamin D promotes negative feedback regulation of TLR signaling via targeting microRNA-155-SOCS1 in macrophages.

    Science.gov (United States)

    Chen, Yunzi; Liu, Weicheng; Sun, Tao; Huang, Yong; Wang, Youli; Deb, Dilip K; Yoon, Dosuk; Kong, Juan; Thadhani, Ravi; Li, Yan Chun

    2013-04-01

    The negative feedback mechanism is essential to maintain effective immunity and tissue homeostasis. 1,25-dihydroxyvitamin D (1,25[OH]2D3) modulates innate immune response, but the mechanism remains poorly understood. In this article, we report that vitamin D receptor signaling attenuates TLR-mediated inflammation by enhancing the negative feedback inhibition. Vitamin D receptor inactivation leads to hyperinflammatory response in mice and macrophage cultures when challenged with LPS, because of microRNA-155 (miR-155) overproduction that excessively suppresses suppressor of cytokine signaling 1, a key regulator that enhances the negative feedback loop. Deletion of miR-155 attenuates vitamin D suppression of LPS-induced inflammation, confirming that 1,25(OH)2D3 stimulates suppressor of cytokine signaling 1 by downregulating miR-155. 1,25(OH)2D3 downregulates bic transcription by inhibiting NF-κB activation, which is mediated by a κB cis-DNA element located within the first intron of the bic gene. Together, these data identify a novel regulatory mechanism for vitamin D to control innate immunity. PMID:23436936

  7. Quercetin protects against aluminium induced oxidative stress and promotes mitochondrial biogenesis via activation of the PGC-1α signaling pathway.

    Science.gov (United States)

    Sharma, Deep Raj; Sunkaria, Aditya; Wani, Willayat Yousuf; Sharma, Reeta Kumari; Verma, Deepika; Priyanka, Kumari; Bal, Amanjit; Gill, Kiran Dip

    2015-12-01

    The present investigation was carried out to elucidate a possible molecular mechanism related to the protective effect of quercetin administration against aluminium-induced oxidative stress on various mitochondrial respiratory complex subunits with special emphasis on the role of PGC-1α and its downstream targets, i.e. NRF-1, NRF-2 and Tfam in mitochondrial biogenesis. Aluminium lactate (10mg/kg b.wt./day) was administered intragastrically to rats, which were pre-treated with quercetin 6h before aluminium (10mg/kg b.wt./day, intragastrically) for 12 weeks. We found a decrease in ROS levels, mitochondrial DNA oxidation and citrate synthase activity in the hippocampus (HC) and corpus striatum (CS) regions of rat brain treated with quercetin. Besides this an increase in the mRNA levels of the mitochondrial encoded subunits - ND1, ND2, ND3, Cyt b, COX1, COX3 and ATPase6 along with increased expression of nuclear encoded subunits COX4, COX5A and COX5B of electron transport chain (ETC). In quercetin treated group an increase in the mitochondrial DNA copy number and mitochondrial content in both the regions of rat brain was observed. The PGC-1α was up regulated in quercetin treated rats along with NRF-1, NRF-2 and Tfam, which act downstream from PGC-1α. Electron microscopy results revealed a significant decrease in the mitochondrial cross-section area, mitochondrial perimeter length and increase in mitochondrial number in case of quercetin treated rats as compared to aluminium treated ones. Therefore it seems quercetin increases mitochondrial biogenesis and makes it an almost ideal flavanoid to control or limit the damage that has been associated with the defective mitochondrial function seen in many neurodegenerative diseases.

  8. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid;

    2014-01-01

    of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...

  9. Cold forming of aluminium - State of the art

    DEFF Research Database (Denmark)

    Bay, Niels

    1997-01-01

    The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable to that of unal...... Elsevier Science S.A....

  10. STRUCTURE OF ECAP ALUMINIUM AFTER DIFFERENT NUMBER OF PASSES

    Directory of Open Access Journals (Sweden)

    Lucia Ilucová

    2011-05-01

    Full Text Available The structure of high purity (99.99% aluminium processed by equal channel angular pressing in the as pressed state after different number of passes was examined using various stereological methods. An extreme inhomogeneity and complicated anisotropy was observed along the body of rod-like specimens.

  11. Zonal distribution of dissolved aluminium in the Mediterranean Sea

    NARCIS (Netherlands)

    Rolison, J. M.; Middag, R.; Stirling, C. H.; Rijkenberg, M. J. A.; de Baar, H. J. W.

    2015-01-01

    Dissolved aluminium (Al) is an important tracer of atmospheric dust input to the oceans. The GEOTRACES expedition to the highly dust impacted Mediterranean Sea afforded the opportunity to study the distribution of dissolved Al in the Mediterranean Sea in detail. Interestingly, the elevated concentra

  12. Development of an aluminium stabilized reinforced superconducting conductor

    Energy Technology Data Exchange (ETDEWEB)

    Fritz, D. [PTR Praezisionstechnik GmbH Maintal (Germany); Horvath, I.L. [Swiss Federal Inst. of Tech., Zuerich (Switzerland); Harzenmoser, M.; Neuenschwander, J. [Swiss Federal Labs. for Materials Testing and Research, Duebendorf (Switzerland); Wittgenstein, F. [CERN, Geneva (Switzerland)

    1996-07-01

    For high performance superconducting magnets as used in large detectors for the High Energy Physics or for magnets of magnetic storage devices (SMES) the mechanical stresses on the conductor go beyond the yield stress level of the high purity matrix stabilizer, specially if aluminium is used. Therefore, a novel method is proposed to join high strength aluminium strips to high purity aluminium stabilizer by using the electron beam (EB) welding. The proposed EB-welding, combined with roll-pressing under vacuum, provides the minimum heat input on the conductor in comparison with other welding techniques. This method provides the advantage to allow the production of very long conductor lengths and includes the potentiality of repairing without losing expensive material. As this process has to be adapted to the high purity aluminium on the one side and to the high strength material on the other, the authors started in a first step with investigation and development of the process, using standard laboratory machines together with laboratory-size tooling. In this report the development program is described and first results of the quality control measurements are presented.

  13. Molecular Characterization of Aluminium (aluminum) Tolerance in Rye

    Science.gov (United States)

    Aluminium (Al) toxicity, affecting around half of the world’s arable land, severely hinders the ability of crop plants to utilize moisture and nutrients by restricting root growth and function. Among the cultivated cereals, rye is the most Al-tolerant and represents an important potential source of ...

  14. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    Science.gov (United States)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  15. Silicon Carbide Tiles for Sidewall Lining in Aluminium Electrolysis Cells

    Institute of Scientific and Technical Information of China (English)

    RUANBo; ZHAOJunguo; 等

    1999-01-01

    The paper introduces the nitride bonded silicon carbide used for sidewall lining in aluminium eletrolysis cells ,including technical process,main properties and application results.Comparison tests on various physical properties of silicon carbide products made by LIRR and other producers worldwide have also been conducted in an independent laboratory.

  16. Local electrochemical behaviour of 7xxx aluminium alloys

    NARCIS (Netherlands)

    Andreatta, F.

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a neg

  17. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    Science.gov (United States)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-09-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN.

  18. Mechanochemical route to the synthesis of nanostructured Aluminium nitride.

    Science.gov (United States)

    Rounaghi, S A; Eshghi, H; Scudino, S; Vyalikh, A; Vanpoucke, D E P; Gruner, W; Oswald, S; Kiani Rashid, A R; Samadi Khoshkhoo, M; Scheler, U; Eckert, J

    2016-09-21

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN.

  19. Mechanochemical route to the synthesis of nanostructured Aluminium nitride.

    Science.gov (United States)

    Rounaghi, S A; Eshghi, H; Scudino, S; Vyalikh, A; Vanpoucke, D E P; Gruner, W; Oswald, S; Kiani Rashid, A R; Samadi Khoshkhoo, M; Scheler, U; Eckert, J

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  20. A vector valued Stefan problem from aluminium industry

    NARCIS (Netherlands)

    Vermolen, F.J.; Vuik, C.

    1998-01-01

    Dissolution of stoichiometric multi-component particles in ternary alloys is an important process occurring during the heat treatment of as-cast aluminium alloys prior to hot-extrusion. A mathematical model is proposed to describe such a process. In this model an equation is given to determine the p

  1. Modelling of aluminium sheet material at elevated temperatures

    NARCIS (Netherlands)

    Haaren, L.; Boogaard, van den A.H.; Huetink, J.

    2004-01-01

    The formability of Al–Mg sheet can be improved considerably, by increasing the temperature. At elevated temperatures, the mechanical response of the material becomes strain rate dependent. To accurately simulate warm forming of aluminium sheet, a material model is required that incorporates the temp

  2. Modelling of contact and friction in aluminium extrusion

    NARCIS (Netherlands)

    Ma, X.; Rooij, de M.B.; Schipper, D.J.

    2010-01-01

    A physical model capable of predicting the friction and sticking/slipping lengths in the bearing channel during unlubricated aluminium extrusion processes is presented. The model takes into account the pressure build up in the extrusion direction in relation with the bearing–extrudate friction and h

  3. Modelling aluminium wire bond reliability in high power OMP devices

    NARCIS (Netherlands)

    Kregting, R.; Yuan, C.A.; Xiao, A.; Bruijn, F. de

    2011-01-01

    In a RF power application such as the OMP, the wires are subjected to high current (because of the high power) and high temperature (because of the heat from IC and joule-heating from the wire itself). Moreover, the wire shape is essential to the RF performance. Hence, the aluminium wire is preferre

  4. Modelling of friction for high temperature extrusion of aluminium alloys

    NARCIS (Netherlands)

    Wang, L.

    2012-01-01

    In recent years, finite-element (FE) simulations have been extensively used in scientific research and industrial practice to analyse the extrusion process. A basic issue of FE simulations is the accuracy of the results, which is mainly determined by the viscoplastic material behaviour of aluminium

  5. Hydrogen evolution from aluminium in reactor containment spray solutions

    International Nuclear Information System (INIS)

    Three different aluminium alloys were exposed to conditions similar to BWR and PWR containment spray waters at 50, 100 and 1500C. BWR deionized water gives corrosion rates of at most 0.05 mm/year and hydrogen concentrations less than 0.1-1%. On the contrary PWR alkaline solutions give very high corrosion rates and hydrogen contents. (Auth.)

  6. Establishment of Integrated Information Displays in Aluminium Surfaces Using Nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan Phuklin; Bladt, Henrik Henriksen; Hansen, Hans Nørgaard

    2005-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in Aluminium that can be penetrated by light. This has resulted in a patent describing how to obtain this effect by etching of local areas in a solid material. The idea behind an invisible display in Aluminum co...... ultra-short pulses, selective etching + anodizing, and electrochemical machining....

  7. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  8. Waste treatment of fission product solutions containing aluminium nitrate

    International Nuclear Information System (INIS)

    In the Rossendorf molybdenum-99 production facility AMOR short-term irradiated aluminium clad fuel elements from the Rossendorf Research Reactor are reprocessed. Following extractive recovery of the enriched uranium the facility system has to be disposed of the fission product-Al(NO3)3 solution. Investigations on waste conditioning of such solutions are presented. (author)

  9. Hydrogen generation from aluminium corrosion in reactor containment spray solutions

    International Nuclear Information System (INIS)

    The aluminium corrosion experiments in reactor containment spray solutions, under the conditions expected to prevail during LOCA in BWR and PWR, were performed in order to investigate relationships between temperature, pH and hydrogen production rates. In order to simulate the conditions in a BWR containment realistic ratios between aluminium surface and water volume and between aluminium surface and oxygen volume were used. Three different aluminium alloys were exposed to spray solutions: AA 1050, AA 5052 and AA 6082. The corrosion rates were measured for BWR solutions (deaerated and aerated) with pH 5 and 9 at 50, 100 and 1500C. The pressure was constantly 0.8 MPa. The hydrogen production rate was measured by means of gas chromatography. In deionized BWR water the corrosion rates did not exceed about 0.05 mm/year in all cases, i.e. were practically independent of temperature and pH. Hydrogen concentrations were less than 0.1 vol.% in cooled dry gas. Corrosion rates and hydrogen production in PWR alkaline solution measured at pH 9.7 and 1500C were very high. AA 5052 alloy was the best material

  10. Electrochemical Characterisation of Filiform Corrosion on Aluminium Rolled Products

    NARCIS (Netherlands)

    Huisert, M.

    2001-01-01

    When aluminium is protected by an organic coating a special form of corrosion can occur underneath the organic coating; filiform corrosion. This form of corrosion manifests itself as threadlike filaments under the coating, it causes local delamination of the coating and the coating cannot protect th

  11. Cavitation-aided grain refinement in aluminium alloys

    NARCIS (Netherlands)

    Atamanenko, T.V.

    2010-01-01

    This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the conditi

  12. Effects of Aluminium in Forest. Results of a pilot experiment

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, J.; Wit, H. de; Nygaard, P.H.

    1996-01-01

    This conference paper deals with an Norwegian pilot project which started in 1995 and finishing early 1999, investigates the solubility and phyto-toxicity of aluminium (Al) in mature forest ecosystems. The project consists of three major parts, including field manipulation study of Norwegian spruce stands, laboratory experiments and modelling Al chemistry in the root zone. 15 refs.

  13. Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

    Science.gov (United States)

    Kramer, Matthias F; Heath, Matthew D

    2014-07-16

    We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

  14. Design of the lines of aluminium drawing. Part 1; Conception des filieres de filage d'aluminium. Partie 1

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    After a general presentation, the second paragraph gives the main reasons of the complexity of the problem to be solved. Coming from the 'sciences of design', these aspects give valuable data to structure the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  15. Decreased toxicity of aluminium when the ionic strength increases in water; Blir aluminium mindre toksisk naar ionestyrken i vannet oeker?

    Energy Technology Data Exchange (ETDEWEB)

    Alstad, E.W. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper evaluates the acute mortality of fish caused by the toxicity of aluminium in water. The evaluation is based on the polymerization hypothesis. According to the author, the level of toxicity decreases when the concentration and charge of ions increase. The paper presents the preliminary results from the executed experiment. 2 refs., 2 figs., 1 tab.

  16. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    International Nuclear Information System (INIS)

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H2PO4− ions to HPO32− ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm−2 and 1.77 mW cm−2, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for bioelectronic applications. • Selective

  17. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Slaughter, Gymama, E-mail: gslaught@umbc.edu; Sunday, Joshua; Stevens, Brian

    2015-08-01

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H{sub 2}PO{sub 4}{sup −} ions to HPO{sub 3}{sup 2−} ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm{sup −2} and 1.77 mW cm{sup −2}, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for

  18. Strain rate effects on mechanical properties in tension of aluminium alloys used in armour applications

    Science.gov (United States)

    Cadoni, E.; Dotta, M.; Forni, D.; Bianchi, S.; Kaufmann, H.

    2012-08-01

    The mechanical properties in tension of two aluminium alloys (AA5059-H131 and AA7039-T651) used in armour applications were determined from tests carried out over a wide range of strain-rates on round specimens. The experimental research was developed in the DynaMat laboratory of the University of Applied Sciences of Southern Switzerland. The target strain rates were set at the following four levels: 10-3, 30, 300 and 1000s-1. The quasi-static tests were performed with a universal electromechanical machine, whereas a hydro-pneumatic machine and a Split Hopkinson Tensile Bar apparatus were used for medium and high strain-rates respectively. The required parameters by the Johnson-Cook constitutive law were also determined.

  19. Behaviour of Thin Aluminium Plates Subjected to Impact by Ogive-nosed Projectiles

    Directory of Open Access Journals (Sweden)

    M.A. Iqbal

    2006-11-01

    Full Text Available A pneumatic gas gun has been used to fire ogive-nosed projectiles on aluminium plates(1mm at varying impact velocities above the ballistic limit. Impact and residual velocities havebeen measured. Deformation of the target plate was studied. Experimental results formed thebasis of a subsequent finite element analysis of the problem using the ABAQUS 6.3 code. TheJohnson-Cook plastic flow and fracture model available in the code were utilised. Explicit finiteelement analysis has been performed to model the perforation phenomenon. Numerical resultswere significantly improved by reducing the element size up to a certain level beyond which nosignificant variation in the results was observed. Adaptive meshing has been found to be usefulin obtaining the accurate results and avoiding the problem of premature termination of theprogram due to excessive element distortion. Experimental and numerical results are comparedand a good agreement between the two has been found.

  20. Strain rate effects on mechanical properties in tension of aluminium alloys used in armour applications

    Directory of Open Access Journals (Sweden)

    Bianchi S.

    2012-08-01

    Full Text Available The mechanical properties in tension of two aluminium alloys (AA5059-H131 and AA7039-T651 used in armour applications were determined from tests carried out over a wide range of strain-rates on round specimens. The experimental research was developed in the DynaMat laboratory of the University of Applied Sciences of Southern Switzerland. The target strain rates were set at the following four levels: 10−3, 30, 300 and 1000s−1. The quasi-static tests were performed with a universal electromechanical machine, whereas a hydro-pneumatic machine and a Split Hopkinson Tensile Bar apparatus were used for medium and high strain-rates respectively. The required parameters by the Johnson-Cook constitutive law were also determined.

  1. Shock wave and material vapour plume propagation during excimer laser ablation of aluminium samples

    Science.gov (United States)

    Jeong, S. H.; Greif, R.; Russo, R. E.

    1999-10-01

    A probe beam deflection technique was utilized to measure the propagation of a shock wave and material vapour plume generated during excimer laser ablation of aluminium samples. The measured transit time of the laser-induced shock wave was compared with the prediction based on an ideal blast-wave model, using the Sedov-Taylor solution. The prediction of the incident laser energy converted into the laser-induced gasdynamic flow utilizing this blast-wave model overestimated the efficiency, even under conditions when the measured shock-wave velocity follows the correct model relation. The propagation of material vapour was measured from the deflection of the probe beam at later times. The propagation velocity of material vapour ranged from 20-40 m s-1 with a greater velocity near the target surface.

  2. 3D self-assembly of aluminium nanoparticles for plasmon-enhanced solar desalination

    Science.gov (United States)

    Zhou, Lin; Tan, Yingling; Wang, Jingyang; Xu, Weichao; Yuan, Ye; Cai, Wenshan; Zhu, Shining; Zhu, Jia

    2016-06-01

    Plasmonics has generated tremendous excitement because of its unique capability to focus light into subwavelength volumes, beneficial for various applications such as light harvesting, photodetection, sensing, catalysis and so on. Here we demonstrate a plasmon-enhanced solar desalination device, fabricated by the self–assembly of aluminium nanoparticles into a three-dimensional porous membrane. The formed porous plasmonic absorber can float naturally on water surface, efficiently absorb a broad solar spectrum (>96%) and focus the absorbed energy at the surface of the water to enable efficient (∼90%) and effective desalination (a decrease of four orders of magnitude). The durability of the devices has also been examined, indicating a stable performance over 25 cycles under various illumination conditions. The combination of the significant desalination effect, the abundance and low cost of the materials, and the scalable production processes suggest that this type of plasmon-enhanced solar desalination device could provide a portable desalination solution.

  3. Earnings Increased 500 Million Yuan Thanks to the Rise of Export Tax Rebate for Aluminium and Copper Products

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    <正>In mid-November,the Ministry of Finance and the State Administration of Taxation issued a tax circular Notification on Raising Export Tax Rebate Rate of the Value-added Tax for Com- modities including Labor-intensive Products, raising the export tax rebate rate by 9% and 13% respectively for refined copper tubes with a outer diameter no more than 25mm and non- alloy aluminium products including rectangular plates,sheets and strips.This is the first time China has adjusted the export tax for nonfer- rous metal products.The adjustment will have a direct positive effect on improving the busi-

  4. Effects of Nano-Aluminium on The Combustion of A PolyNIMMO-Based Propellant

    Institute of Scientific and Technical Information of China (English)

    Clive Woodley; Peter Henning

    2014-01-01

    Propellants containing micro-aluminium particles have been shown to produce faster burn rates than conventional gun propellants.However,they are also more abrasive than conventional propellants.Nano-material propellants have been reported to give similar benefits to micron-material propellants but without the disadvantage of increased abrasion.Tests were conducted to compare the burn rates,ignitability and wear rates of a propellant loaded with 0% aluminium,15% micro-aluminium and 15%nano-aluminium.Closed vessel tests showed a burn rate increase of 39% in the range 30-250 MPa,and 70% at low pressure (50-100 MPa)for the nano-aluminium propellant compared with the baseline propellant.The micro-aluminium propellant showed only a 10% increase in the burn rate compared with the standard propellant.The ignition delay for the nano-aluminium propellant was slightly shorter than that of the baseline propellant.Substantially increased wear rates were measured for the micro-aluminium propellant.The nano-aluminium propellant showed reduced wear rates compared with the micro-aluminium propellant but these were still substantially greater than those for the baseline propellant.

  5. MicroRNA-106b-25 cluster targets β-TRCP2, increases the expression of Snail and enhances cell migration and invasion in H1299 (non small cell lung cancer) cells

    International Nuclear Information System (INIS)

    Highlights: •miR-106b-25 cluster directly targets the 3′UTR of the β-TRCP2 transcript. •β-TRCP2 mRNA was lower in H1299 cells stably expressing miR-106b-25 cluster. •miR-106b-25 cluster increased the expression of Snail. •miR-106b-25 cluster promoted the migration, colony formation and invasion. •miR-106b-25 cluster enhanced endothelial tube formation. -- Abstract: Lung cancer causes high mortality without a declining trend and non small cell lung cancer represents 85% of all pulmonary carcinomas. MicroRNAs (miRNAs) serve as fine regulators of proliferation, migration, invasion/metastasis and angiogenesis of normal and cancer cells. Using TargetScan6.2, we predicted that the ubiquitin ligase, β-TRCP2, could be a target for two of the constituent miRNAs of the miR-106b-25 cluster (miR-106b and miR-93). We generated a stable clone of miR-106b-25 cluster (CL) or the empty vector (EV) in H1299 (non small cell lung cancer) cells. The expression of β-TRCP2 mRNA was significantly lower in CL than that in EV cells. Transient expression of miR-93 but not antimiR-93 decreased the expression of β-TRCP2 mRNA in H1299 cells. β-TRCP2-3′UTR reporter assay revealed that its activity in CL cells was only 60% of that in EV cells. Snail protein expression was higher in CL than that in EV cells and H1299 cells exhibited an increase in the expression of Snail upon transient transfection with miR-93. miR-106b-25 cluster-induced migration of CL measured by scratch assay was more than that in EV cells and no significant difference in migration was observed between antimiR-93-transfected H1299 cells and the corresponding control-oligo-transfected cells. miR-106b-25 cluster-induced migration of CL cells was again confirmed in a Boyden chamber assay without the matrigel. CL cells were more invasive than EV cells when assessed using Boyden chambers with matrigel but there were no significant changes in the cell viabilities between EV and CL cells. Colony formation assay

  6. MicroRNA-106b-25 cluster targets β-TRCP2, increases the expression of Snail and enhances cell migration and invasion in H1299 (non small cell lung cancer) cells

    Energy Technology Data Exchange (ETDEWEB)

    Savita, Udainiya; Karunagaran, Devarajan, E-mail: karuna@iitm.ac.in

    2013-05-17

    Highlights: •miR-106b-25 cluster directly targets the 3′UTR of the β-TRCP2 transcript. •β-TRCP2 mRNA was lower in H1299 cells stably expressing miR-106b-25 cluster. •miR-106b-25 cluster increased the expression of Snail. •miR-106b-25 cluster promoted the migration, colony formation and invasion. •miR-106b-25 cluster enhanced endothelial tube formation. -- Abstract: Lung cancer causes high mortality without a declining trend and non small cell lung cancer represents 85% of all pulmonary carcinomas. MicroRNAs (miRNAs) serve as fine regulators of proliferation, migration, invasion/metastasis and angiogenesis of normal and cancer cells. Using TargetScan6.2, we predicted that the ubiquitin ligase, β-TRCP2, could be a target for two of the constituent miRNAs of the miR-106b-25 cluster (miR-106b and miR-93). We generated a stable clone of miR-106b-25 cluster (CL) or the empty vector (EV) in H1299 (non small cell lung cancer) cells. The expression of β-TRCP2 mRNA was significantly lower in CL than that in EV cells. Transient expression of miR-93 but not antimiR-93 decreased the expression of β-TRCP2 mRNA in H1299 cells. β-TRCP2-3′UTR reporter assay revealed that its activity in CL cells was only 60% of that in EV cells. Snail protein expression was higher in CL than that in EV cells and H1299 cells exhibited an increase in the expression of Snail upon transient transfection with miR-93. miR-106b-25 cluster-induced migration of CL measured by scratch assay was more than that in EV cells and no significant difference in migration was observed between antimiR-93-transfected H1299 cells and the corresponding control-oligo-transfected cells. miR-106b-25 cluster-induced migration of CL cells was again confirmed in a Boyden chamber assay without the matrigel. CL cells were more invasive than EV cells when assessed using Boyden chambers with matrigel but there were no significant changes in the cell viabilities between EV and CL cells. Colony formation assay

  7. Obesity–insulin targeted genes in the 3p26-25 region in human studies and LG/J and SM/J mice

    Science.gov (United States)

    Kraja, Aldi T.; Lawson, Heather A.; Arnett, Donna K.; Borecki, Ingrid B.; Broeckel, Ulrich; de las Fuentes, Lisa; Hunt, Steven C.; Province, Michael A.; Cheverud, James; Rao, D.C.

    2012-01-01

    Identifying metabolic syndrome (MetS) genes is important for novel drug development and health care. This study extends the findings on human chromosome 3p26-25 for an identified obesity–insulin factor QTL, with an LOD score above 3. A focused association analysis comprising up to 9578 African American and Caucasian subjects from the HyperGEN Network (908 African Americans and 1025 whites), the Family Heart Study (3035 whites in time 1 and 1943 in time 2), and the Framingham Heart Study (1317 in Offspring and 1320 in Generation 3) was performed. The homologous mouse region was explored in an F16 generation of an advanced intercross between the LG/J and SM/J inbred strains, in an experiment where 1002 animals were fed low-fat (247 males; 254 females) or high-fat (253 males; 248 females) diets. Association results in humans indicate pleiotropic effects for SNPs within or surrounding CNTN4 on obesity, lipids and blood pressure traits and for SNPs near IL5RA, TRNT1, CRBN, and LRRN1 on central obesity and blood pressure. Linkage analyses of this region in LG/J × SM/J mice identify a highly significant pleiotropic QTL peak for insulin and glucose levels, as well as response to glucose challenge. The mouse results show that insulin and glucose levels interact with high and low fat diets and differential gene expression was identified for Crbn and Arl8b. In humans, ARL8B resides ~137 kbps away from BHLHE40, expression of which shows up-regulation in response to insulin treatment. This focused human genetic analysis, incorporating mouse research evidenced that 3p26-25 has important genetic contributions to MetS components. Several of the candidate genes have functions in the brain. Their interaction with MetS and the brain warrants further investigation. PMID:22386932

  8. Obesity-insulin targeted genes in the 3p26-25 region in human studies and LG/J and SM/J mice.

    Science.gov (United States)

    Kraja, Aldi T; Lawson, Heather A; Arnett, Donna K; Borecki, Ingrid B; Broeckel, Ulrich; de las Fuentes, Lisa; Hunt, Steven C; Province, Michael A; Cheverud, James; Rao, D C

    2012-08-01

    Identifying metabolic syndrome (MetS) genes is important for novel drug development and health care. This study extends the findings on human chromosome 3p26-25 for an identified obesity-insulin factor QTL, with an LOD score above 3. A focused association analysis comprising up to 9578 African American and Caucasian subjects from the HyperGEN Network (908 African Americans and 1025 whites), the Family Heart Study (3035 whites in time 1 and 1943 in time 2), and the Framingham Heart Study (1317 in Offspring and 1320 in Generation 3) was performed. The homologous mouse region was explored in an F(16) generation of an advanced intercross between the LG/J and SM/J inbred strains, in an experiment where 1002 animals were fed low-fat (247 males; 254 females) or high-fat (253 males; 248 females) diets. Association results in humans indicate pleiotropic effects for SNPs within or surrounding CNTN4 on obesity, lipids and blood pressure traits and for SNPs near IL5RA, TRNT1, CRBN, and LRRN1 on central obesity and blood pressure. Linkage analyses of this region in LG/J×SM/J mice identify a highly significant pleiotropic QTL peak for insulin and glucose levels, as well as response to glucose challenge. The mouse results show that insulin and glucose levels interact with high and low fat diets and differential gene expression was identified for Crbn and Arl8b. In humans, ARL8B resides ~137kbps away from BHLHE40, expression of which shows up-regulation in response to insulin treatment. This focused human genetic analysis, incorporating mouse research evidenced that 3p26-25 has important genetic contributions to MetS components. Several of the candidate genes have functions in the brain. Their interaction with MetS and the brain warrants further investigation.

  9. Numerical and experimental investigations of aluminium powder compaction; Numerische und experimentelle Untersuchungen zum Pulverpressen von Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Hanini, K.; Doege, E.; Schmidt-Juergensen, R. [Institut fuer Umformtechnik und Umformmaschinen, (IFUM) Universitaet Hannover, Welfengarten 1A, 30167 Hannover (Germany)

    2003-08-01

    The FEM simulation is a powerful means which can drastically reduce the time to production and costs in the optimization of powder forming processes. The current paper investigates experimentally and numerically die compaction of aluminium powder. The plastic deformation is formulated by using the Drucker-Prager-Cap-model. This yield criterion describes the compressibility of porous bodies and allows the prediction of crack formation in the green compact. Axial compaction tests have been performed to determine material parameters for hardening. Simulation examples are presented to demonstrate the ability of the model to compute the distribution of the relative density. Furthermore, the compaction of an axisymmetric workpiece was simulated in order to determine optimal tools kinematics and to avoid crack formation. (Abstract Copyright [2003], Wiley Periodicals, Inc.) [German] Die Auslegung und Optimierung pulvertechnologischer Umformverfahren basiert bisher zu einem grossen Teil auf Erfahrungswissen. Die numerische Simulation bietet hierbei eine kosten- und zeitsparende Alternative. Besonders hat sich die Finite-Elemente-Methode (FEM) als leistungsfaehiges Simulationsverfahren bewaehrt. Im Rahmen dieser Arbeit wird das Pulverpressen von Aluminiumpulver numerisch und experimentell untersucht. Hierbei wird das Drucker-Prager-Cap-Modell verwendet, um das kompressible Verhalten des Pulvers abzubilden und moegliche Rissbildungen waehrend des Pressvorgangs vorherzusagen. Durch Pressversuche werden die Materialkennwerte fuer dieses Modell hinsichtlich der Verdichtung und Verfestigung des Aluminiumpulvers ermittelt. Der Pressvorgang wird anhand ausgewaehlter Referenzbauteile simuliert. Von besonderem Interesse ist hierbei die Berechnung der Verteilung der relativen Dichte und die Vermeidung der Rissbildung durch Optimierung der Stempelkinematik. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  10. Aluminium content of foods originating from aluminium-containing food additives.

    Science.gov (United States)

    Ogimoto, Mami; Suzuki, Kumi; Haneishi, Nahoko; Kikuchi, Yuu; Takanashi, Mayu; Tomioka, Naoko; Uematsu, Yoko; Monma, Kimio

    2016-09-01

    Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples. PMID:27092423

  11. Steel sheet composite materials with foamed aluminium; Stahlblechverbundwerkstoffe mit geschaeumtem Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Baumeister, J.; Weber, M. [Institut fuer Angewandte Materialforschung, Bremen (Germany); Bleck, W.; Hagen, H. von [Technische Hochschule Aachen (Germany). Lehrstuhl und Inst. fuer Eisenhuettenkunde

    1999-07-01

    Sandwich structured steel sheets with a core of foamed aluminium can be produced by roll-bonding and glueing. Results of corrosion tests and laser welding tests so far were positive. Several applications have been proposed but none of them has been implemented as yet. The material is recommended for applications with a profile of requirements comprising structurally and functionally relevant characteristics. Recycling is unproblematic. [German] Zur Herstellung von Stahlblechsandwichverbunden mit einem Aluminiumschaumkern lassen sich die Verfahren Walzplattieren und Kleben einsetzen. Es sind Sandwichverbunde mit Gesamtdichten von 0,7 bis 2,0 g/cm{sup 3} und Gesamtdicken zwischen 10 und 32 mm darstellbar. Die Tafelgroessen fuer die vielversprechendsten Verfahren liegen derzeit bei ueber DIN A3 (konventionell geschaeumt) oder 160 mm x mehrere m (kontinuierlich im Banddurchlaufofen geschaeumt) und 2 m x 600 mm (geklebt). Es lassen sich gute mechanische Eigenschaften des Sandwichverbundes (Biegesteifigkeit) und hohe Versagensreserven bei Druck- und Biegebeanspruchungen sowie interessante funktionelle Eigenschaften (z.B. hohe Energieaufnahme) erzielen. Aus Tastversuchen zu Korrosionseigenschaften und Fuegeverfahren (Laserschweissen) konnten positive Resultate gewonnen werden. Vorschlaege zu Anwendungen bestehen, aber ein direkter Einsatz ist noch nicht realisiert worden. Ein Einsatz des Werkstoffverbundes ist sinnvoll in Gebieten, in denen ein Anforderungsprofil von strukturell und funktionell relevanten Eigenschaften vorherrscht. Das Recycling der rein metallischen Verbunde ist problemlos. (orig.)

  12. Performance of commercial aluminium alloys as anodes in gelled electrolyte aluminium-air batteries

    Science.gov (United States)

    Pino, M.; Chacón, J.; Fatás, E.; Ocón, P.

    2015-12-01

    The evaluation of commercial aluminium alloys, namely, Al2024, Al7475 and Al1085, for Al-air batteries is performed. Pure Al cladded Al2024 and Al7475 are also evaluated. Current rates from 0.8 mA cm-2 to 8.6 mA cm-2 are measured in a gel Al-air cell composed of the commercial alloy sample, a commercial air-cathode and an easily synthesizable gelled alkaline electrolyte. The influence of the alloying elements and the addition to the electrolyte of ZnO and ZnCl2, as corrosion inhibitors is studied and analysed via EDX/SEM. Specific capacities of up to 426 mAh/g are obtained with notably flat potential discharges of 1.3-1.4 V. The competition between self-corrosion and oxidation reactions is also discussed, as well as the influence of the current applied on that process. Al7475 is determined to have the best behaviour as anode in Al-air primary batteries, and cladding process is found to be an extra protection against corrosion at low current discharges. Conversely, Al1085 provided worse results because of an unfavourable metallic composition.

  13. Cross-sections of large-angle hadron production in proton-- and pion--nucleus interactions VIII: aluminium nuclei and beam momenta from $\\pm$ 3 GeV/c to $\\pm$ 15 GeV/c

    CERN Document Server

    Bolshakova, A; Chelkov, G; Dedovitch, D; Elagin, A; Emelyanov, D; Gostkin, M; Guskov, A; Kroumchtein, Z; Nefedov, Y; Nikolaev, K; Zhemchugov, A; Dydak, F; Wotschack, J; De Min, A; Ammosov, V; Gapienko, V; Koreshev, V; Semak, A; Sviridov, Y; Usenko, E; Zaets, V

    2012-01-01

    We report on double-differential inclusive cross-sections of the production of secondary protons, charged pions, and deuterons, in the interactions with a 5\\% $\\lambda_{\\rm int}$ thick stationary aluminium target, of proton and pion beams with momentum from $\\pm3$~GeV/{\\it c} to $\\pm15$~GeV/{\\it c}. Results are given for secondary particles with production angles $20^\\circ < \\theta < 125^\\circ$. Cross-sections on aluminium nuclei are compared with cross-sections on beryllium, carbon, copper, tin, tantalum and lead nuclei.

  14. Transmission of broad W/Rh and W/Al (target/filter) x-ray beams operated at 25–49 kVp through common shielding materials

    International Nuclear Information System (INIS)

    Purpose: To provide transmission data for broad 25–39 kVp (kilovolt peak) W/Rh and 25–49 kVp W/Al (target/filter, W—tungsten, Rh—rhodium, and Al—aluminum) x-ray beams through common shielding materials, such as lead, concrete, gypsum wallboard, wood, steel, and plate glass. Methods: The unfiltered W-target x-ray spectra measured on a Selenia Dimensions system (Hologic Inc., Bedford, MA) set at 20–49 kVp were, respectively, filtered using 50-μm Rh and 700-μm Al, and were subsequently used for Monte Carlo calculations. The transmission of broad x-ray beams through shielding materials was simulated using Geant4 low energy electromagnetic physics package with photon- and electron-processes above 250 eV, including photoelectric effect, Compton scattering, and Rayleigh scattering. The calculated transmission data were fitted using Archer equation with a robust fitting algorithm. Results: The transmission of broad x-ray beams through the above-mentioned shielding materials was calculated down to about 10−5 for 25–39 kVp W/Rh and 25–49 kVp W/Al. The fitted results of α, β, and γ in Archer equation were provided. The α values of kVp ⩾ 40 were approximately consistent with those of NCRP Report No. 147. Conclusions: These data provide inputs for the shielding designs of x-ray imaging facilities with W-anode x-ray beams, such as from Selenia Dimensions.

  15. Assessment of the biological effects of welding fumes emitted from metal inert gas welding processes of aluminium and zinc-plated materials in humans.

    Science.gov (United States)

    Hartmann, L; Bauer, M; Bertram, J; Gube, M; Lenz, K; Reisgen, U; Schettgen, T; Kraus, T; Brand, P

    2014-03-01

    The aim of this study was to investigate biological effects and potential health risks due to two different metal-inert-gas (MIG) welding fumes (MIG welding of aluminium and MIG soldering of zinc coated steel) in healthy humans. In a threefold cross-over design study 12 male subjects were exposed to three different exposure scenarios. Exposures were performed under controlled conditions in the Aachener Workplace Simulation Laboratory (AWSL). On three different days the subjects were either exposed to filtered ambient air, to welding fumes from MIG welding of aluminium, or to fumes from MIG soldering of zinc coated materials. Exposure was performed for 6 h and the average fume concentration was 2.5 mg m(-3). Before, directly after, 1 day after, and 7 days after exposure spirometric and impulse oscillometric measurements were performed, exhaled breath condensate (EBC) was collected and blood samples were taken and analyzed for inflammatory markers. During MIG welding of aluminium high ozone concentrations (up to 250 μg m(-3)) were observed, whereas ozone was negligible for MIG soldering. For MIG soldering, concentrations of high-sensitivity CRP (hsCRP) and factor VIII were significantly increased but remained mostly within the normal range. The concentration of neutrophils increased in tendency. For MIG welding of aluminium, the lung function showed significant decreases in Peak Expiratory Flow (PEF) and Mean Expiratory Flow at 75% vital capacity (MEF 75) 7 days after exposure. The concentration of ristocetin cofactor was increased. The observed increase of hsCRP during MIG-soldering can be understood as an indicator for asymptomatic systemic inflammation probably due to zinc (zinc concentration 1.5 mg m(-3)). The change in lung function observed after MIG welding of aluminium may be attributed to ozone inhalation, although the late response (7 days after exposure) is surprising.

  16. SINFONI spectra of heavily obscured AGNs in COSMOS: evidence of outflows in a MIR/O target at z$\\sim2.5$

    CERN Document Server

    Perna, M; Salvato, M; Cresci, G; Lanzuisi, G; Berta, S; Delvecchio, I; Fiore, F; Lutz, D; Floc'h, E Le; Mainieri, V; Riguccini, L

    2015-01-01

    We present new data for four candidate obscured Compton-Thick (CT) quasars at z $\\sim$1-2.5 observed with SINFONI VLT spectrograph in AO mode. These sources were selected from a 24$\\mu$m Spitzer MIPS survey of the COSMOS field, on the basis of red mid-infrared-to-optical and optical-to-near-infrared colours, with the intention of identifying active galactic nuclei (AGNs) in dust enshrouded environments, where most of the black hole mass is assembled in dust enshrouded environments. Near infrared spectra were analyzed in order to check for emission line features and to search for broad components in the [OIII]-H$\\beta$ and H$\\alpha$-[NII] regions. X-ray spectral analysis, radio and MIR diagnostics, and SED fitting have also been employed to study the nature of the sources. We successfully identified three objects for which we had only a photometric redshift estimate. Based on their emission line diagnostics and on ancillary multi-wavelength constraints, we find that all four targets harbor obscured AGNs. Broad...

  17. Specific activation of 2'-5'oligoadenylate synthetase gene promoter by hepatitis C virus-core protein: A potential for developing hepatitis C virus targeting gene therapy

    Institute of Scientific and Technical Information of China (English)

    Ying Wang; Shan-Shan Mao; Qiong-Qiong He; Yuan Zi; Ji-Fang Wen; De-Yun Feng

    2009-01-01

    AIM: To examine whether 2'-5'oligoadenylate synthetase (OAS) gene promoter can be specifically activated by hepatitis C virus (HCV)-core protein.METHODS: Human embryo hepatic cell line L02 was transfected with pcDNA3.1-core plasmid and selected by G418. Expression of HCV-core was detected by reverse transcription polymerase chain reaction and Western blotting. The OAS promoter sequence was amplified from the genomic DNA and inserted into pGL3-basic vector. The resultant pGL3-OAS-Luci plasmid was transiently transfected into L02/core cells and luciferase activity was assayed.RESULTS: L02/core cell line stably expressing HCV-core protein was established. The pGL3-OAS-Luci construct exhibited significant transcriptional activity in the L02/core cells but not in the L02 cells.CONCLUSION: HCV-core protein activates the OAS gene promoter specifically and effectively. Utilization of OAS gene promoter would be an ideal strategy for developing HCV-specific gene therapy.

  18. Temperature and thermal stress fields during the pulse train of long-pulse laser irradiating aluminium alloy plate

    Science.gov (United States)

    Zhang, Wei; Jin, Guangyong; Gu, Xiu-ying

    2014-12-01

    Based on Von Mises yield criterion and elasto-plastic constitutive equations, an axisymmetric finite element model of a Gaussian laser beam irradiating a metal substrate was established. In the model of finite element, the finite difference hybrid algorithm is used to solve the problem of transient temperature field and stress field. Taking nonlinear thermal and mechanical properties into account, transient distributions of temperature field and stress fields generated by the pulse train of long-pulse laser in a piece of aluminium alloy plate were computed by the model. Moreover,distributions as well as histories of temperature and stress fields were obtained. Finite element analysis software COMSOL is used to simulate the Temperature and thermal stress fields during the pulse train of long-pulse laser irradiating 7A04 aluminium alloy plate. By the analysis of the results, it is found that Mises equivalent stress on the target surface distribute within the scope of the center of a certain radius. However, the stress is becoming smaller where far away from the center. Futhermore, the Mises equivalent stress almost does not effect on stress damage while the Mises equivalent stress is far less than the yield strength of aluminum alloy targets. Because of the good thermal conductivity of 7A04 aluminum alloy, thermal diffusion is extremely quick after laser irradiate. As a result, for the multi-pulsed laser, 7A04 aluminum alloy will not produce obvious temperature accumulation when the laser frequency is less than or equal to 10 Hz. The result of this paper provides theoretical foundation not only for research of theories of 7A04 aluminium alloy and its numerical simulation under laser radiation but also for long-pulse laser technology and widening its application scope.

  19. INVESTIGATION OF THE POTENTIAL PHYSIO-PATOLOGICAL EFFECTS OF ALUMINIUM IN PATIENTS WITH ALZHEIMER SPECIFIC SYMPTOMS

    Directory of Open Access Journals (Sweden)

    Constantin Bǎlǎeț

    2013-06-01

    Full Text Available In the past few years, there has been developed an idea about the connection between the Presence of aluminium in human blood and Alzheimer disease. The goal of our study was to demonstrate that there is a connection between the aluminium in the patients’ blood (who presented specific symptoms and Alzheimer disease’s occurrence, having a physiopathological determination. Aluminium dosage in a group of patients was analyzed (according to some pre-established procedures. 65% of the patients had 1-5% higher than normal values for aluminium level. Aluminium intoxication could lead to syndromes which could affect peoples’ activity. The general physicians must be aware of the need for detecting the aluminium in blood, of interpreting the physiopathological changes and of monitoring these changes in order to detect early symptoms of Alzheimer disease.

  20. The nature of point defects in plastically deformed aluminium

    International Nuclear Information System (INIS)

    In order to find out which types of point defect are produced by plastic deformation, 57Co-doped aluminium specimens were cold worked at various temperatures by unidirectional tensile deformation or cyclic torsion. The specimens were then annealed at increasing temperatures, and the trapping of defects at the 57Co probes was studied by Moessbauer spectroscopy. In none of the experiments were interstitials found, although it is known that in aluminium 57Co probes readily trap interstitials after low-temperature particle irradiation. However, vacancy trapping was found in two temperature ranges corresponding to two different migration energies of vacancies: in dislocations Esub(m)sup(d) approx.0.2 to 0.3 eV and in the lattice Esub(m) approx.= 0.6 eV. The consequences of the results on models of point defect production by cold working are discussed. (author)

  1. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines

    DEFF Research Database (Denmark)

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E;

    2016-01-01

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year....... Two patients had skin biopsies performed from their skin lesions, and 2 patients had the nodules surgically removed. Forty-two children had a patch-test performed with 2% aluminium chloride hexahydrate in petrolatum and 39 of them (92%) had a positive reaction. The persistent skin reactions were...... period 2003 to 2013 we identified 47 children with persistent skin reactions caused by childhood vaccinations. Most patients had a typical presentation of persisting pruritic subcutaneous nodules. Five children had a complex diagnostic process involving paediatricians, orthopaedics and plastic surgeons...

  2. Environment pollution with aluminium around a coalburning electric power plant

    International Nuclear Information System (INIS)

    The experiments were carried out from November 1991 till November 1993 on the area surrounding an electric power plant within the circle of 20 km diameter and five geographical directions (N, S, SE, E, W). The results presented in this paper have indicated the threats caused by emissions of the power plant ashes and dusts. Mean aluminium content in soil has been multiply surpassed on the area studied. This must have as impact on fauna and flora. The distribution and intensity of pollution is determined first of all by the distance from the emitters and direction of prevailing winds. A part of aluminium contained in water soluble compounds can be distributed on large areas, what adds a lot to the threat to animals. That is why high chimneys do not solve the problem of pollution around big industrial plants. (author)

  3. Nano α-alumina powders from aluminium dross waste

    International Nuclear Information System (INIS)

    The paper describes a solvo thermal chemical process to recycle aluminium dross waste into nano α-alumina powder. The process includes washing to remove the unwanted sodium follow by dissolving of this waste with dilute acid. The solvo thermal process then proceed with addition of propanol to crystallize the aluminium hydroxide. XRD analysis of this crystal shows that it belongs to Gibbs site (Al(OH)3). The crystals were then calcined at 1300 degree C where white powder was produced. Characteristic studies were then performed on this powder using XRD, SEM, EDX and particle size analysis showing that it has single α-alumina crystal phase with almost spherical shape. As the initial particle size is coarse and had a mean particle size of 3.80 μm, high speed wet milling was used and enable to reduce it to 0.49 μm. (Author)

  4. High-pressure direct synthesis of aluminium nitride

    CERN Document Server

    Bockowski, M; Grzegory, I; Krukowski, S; Wróblewski, M; Porowski, S

    2002-01-01

    We report the results of direct synthesis of aluminium nitride (AlN) under high nitrogen pressure up to 1 GPa and temperatures up to 2000 K. At pressure from 10 to 650 MPa we observe the combustion synthesis of AlN. As the result of the combustion process one can obtain the AlN sintered powder or AlN/Al metal matrix composites. For N sub 2 pressure higher than 650 MPa the crystal growth of AlN from the solution of atomic nitrogen in aluminium is possible. Both needle-like and bulk AlN single crystals, up to 1 cm and 1 mm, respectively, have been obtained.

  5. Thermal Effect of Ceramic Nanofiller Aluminium Nitride on Polyethylene Properties

    Directory of Open Access Journals (Sweden)

    Omer Bin Sohail

    2012-01-01

    Full Text Available Ethylene polymerization was done to form polyethylene nano-composite with nanoaluminum nitride using zirconocene catalysts. Results show that the catalytic activity is maximum at a filler loading of 15 mg nanoaluminum nitride. Differential scanning calorimeter (DSC and X-ray diffraction (XRD results show that percentage crystallinity was also marginally higher at this amount of filler. Thermal behavior of polyethylene nanocomposites (0, 15, 30, and 45 mg was studied by DSC and thermal gravimetric analyzer (TGA. Morphology of the component with 15 mg aluminium nitride is more fibrous as compared to 0 mg aluminium nitride and higher filler loading as shown by SEM images. In order to understand combustibility behavior, tests were performed on microcalorimeter. Its results showed decrease in combustibility in polyethylene nanocomposites as the filler loading increases.

  6. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    K T Kashyap; T Chandrashekar

    2001-08-01

    Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the scientific literature. The nucleant effects i.e. which particle and its characteristics nucleate -Al, has been the subject of intensive research. Lately the solute effect i.e. the effect of dissolved titanium on grain refinement, has come into forefront of grain refinement research. The present paper attempts to review the literature on the nucleant effects and solute effects on grain refinement and addresses the importance of dissolved titanium in promoting nucleation of -Al on nucleant particles.

  7. Properties of native ultrathin aluminium oxide tunnel barriers

    CERN Document Server

    Gloos, K; Pekola, J P

    2003-01-01

    We have investigated planar metal-insulator-metal tunnel junctions with aluminium oxide as the dielectricum. These oxide barriers were grown on an aluminium electrode in pure oxygen at room temperature till saturation. By applying the Simmons model we derived discrete widths of the tunnelling barrier, separated by DELTA s approx 0.38 nm. This corresponds to the addition of single layers of oxygen atoms. The minimum thickness of s sub 0 approx 0.54 nm is then due to a double layer of oxygen. We found a strong and systematic dependence of the barrier height on the barrier thickness. Breakdown fields up to 5 GV m sup - sup 1 were reached. They decreased strongly with increasing barrier thickness. Electrical breakdown could be described by a metal-insulator like transition of the dielectric barrier due to the large density of tunnelling electrons.

  8. Muon motion in pure and weakly doped aluminium

    CERN Document Server

    Niinikoski, T O; Karlsson, E; Kehr, K W; Norlin, L O; Richter, D; Welter, J M

    1981-01-01

    The authors have studied the diffusion and localization of positive muons in pure and weakly doped aluminium, in the temperature range 30 mK-100K, by measuring the damping parameter of the muon spin rotation ( mu SR) signal. In this paper they discuss some of their recent results and draw the following conclusions: i) in pure Al, positive muons are delocalized in band states (coherent motion); ii) in Al doped with 5-70 ppm Mn, the temperature, concentration and field dependences of the damping parameter suggest diffusion or capture limited trapping to octahedral interstitial sites in the aluminium lattice below 1K; iii) above 2K a two-state diffusion-trapping model explains well the peak in the damping parameter, which appears at 15-50K for the dopants Mn, Mg, Li and Ag so far studied. (11 refs).

  9. Buffering effects on electrograining of aluminium in nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Koroleva, E.V. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom)]. E-mail: e.koroleva@umist.ac.uk; Thompson, G.E. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Skeldon, P. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Hollrigl, G. [Alcan Technology and Management Ltd., Bad. Bahnhofstrasse 16, CH-8212 Neuhausen (Switzerland); Lockwood, S. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom); Smith, G. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom)

    2005-09-01

    Electrograining of a binary Al-Si alloy has been undertaken in nitric acid based electrolytes, with the resultant surfaces examined by scanning and transmission electron microscopies. Depending on electrograining conditions, the pit appearance varies from hemispherical to large lateral pits, with the latter favoured in relatively acidic electrolytes. The conditions prevailing in the pit have been explored through use of aluminium ion additions to the nitric acid electrolyte as well as additions of species which influence the precipitation and dissolution of aluminium hydroxide. These confirm that control of the pit solution pH, through hydroxide generation, as a result of the selected electrograining conditions and consequent anodic and cathodic polarisation, enables tailoring of the resultant electrograined surface appearance.

  10. Potentiostatic Electrochemical Preparation and Characterisation of Aluminium Containing Nickel Selenide

    Directory of Open Access Journals (Sweden)

    Sandeep Gohar

    2014-01-01

    Full Text Available The wide range of properties exhibited by Al based alloy makes them suitable for different applications. Aluminium containing nickel Selenide ternary alloy possess considerable corrosion resistance as compared to their pure metal counterparts. The objective of the present work has been focused on the preparation and characterisation of its thin film. Alloying with Aluminium improve the oxidation resistance and increases the heat conductivity of the alloy. There is always a high demand for plating Al and its alloys in automotive and aerospace products, house-hold goods, and artificial jewellery etc,. The morphological and the structural studies of the electrodeposited thin film were determined by Scanning Electron Microscope (SEM images and X-Ray Diffraction Pattern (XRD while elemental composition has been done by Energy Dispersive X-Ray Spectroscopy (EDAX analysis.

  11. Evolution of Structural Damage in Aluminium Irradiated with Xenon Ions

    CERN Document Server

    Hofmann, A

    2001-01-01

    Structural defect evolution in high-purity aluminium both as-irradiated and annealed after irradiation has been investigated by transmission electron microscopy. The foils of high-purity aluminium were irradiated with 124 MeV Xe ions with fluence up to 2\\cdot 10^{16} Xe^+ cm^{-2} at room temperature and at 100 ^{o}C. The samples irradiated at 100 ^{o}C were annealed at 480 and 600 ^{o}C. At initial stage of irradiation, at low fluence (\\leq 2\\cdot 10^{14} Xe^+ cm^{-2}) the isolated dislocation loops are observed. When ion fluence increased the loops grow. At fluences above 10^{15} Xe^+ cm^{-2} cm the microstructure is characterized by high-density small voids (pores) which are grown and slowly merged with fluence increasing. For these conditions, the most possible mechanism of pore growth is their diffusion-controlled coalescence.

  12. Sputter deposition of aluminium on colloidal polymer templates

    Energy Technology Data Exchange (ETDEWEB)

    Gehrke, Rainer; Buffet, Adeline; Couet, Sebastien; Schlage, Kai; Roth, Stephan V.; Roehlsberger, Ralf [HASYLAB, DESY, Hamburg (Germany); Herzog, Gerd [HASYLAB, DESY, Hamburg (Germany); Inst. f. Exp. Phys., Univ. Hamburg (Germany); Kaune, Gunar; Koerstgens, Volker; Meier, Robert; Metwalli, Ezzeldin; Mueller-Buschbaum, Peter [TU Muenchen, Physik-Department, Garching (Germany); Wurth, Wilfried [Inst. f. Exp. Phys., Univ. Hamburg (Germany)

    2009-07-01

    This work addresses an approach to the formation of metal nanowire meshes on surfaces. Colloidal dispersions of 100 nm polystyrene spheres were spincoated on silicon. Islands of packed layers of spheres were formed which served as template for sputter deposition of aluminium. Structure formation was investigated with grazing incidence small angle X-ray scattering at beamline BW4 at HASYLAB/DESY using an in-situ sputtering chamber, thus scattering could be observed during metal deposition. The measurements indicate, that at the beginning of the deposition the metal atoms assemble in the indentations between the spheres, only after longer sputtering times the surface becomes completely covered with aluminium. If an unsputtered sample was heated beyond the glass transition temperature the lateral ordering vanished, if sputtering was stopped before complete metal coverage ordering remained upon heating. This indicates that the metal forms a stable structure separating the polymer spheres from each other.

  13. Experimental evidence for a dynamical crossover in liquid aluminium.

    Science.gov (United States)

    Demmel, F; Fraile, A; Szubrin, D; Pilgrim, W-C; Morkel, C

    2015-11-18

    The temperature dependence of the dynamic structure factor at next-neighbour distances has been investigated for liquid aluminium. This correlation function is a sensitive parameter for changes in the local environment and its Fourier transform was measured in a coherent inelastic neutron scattering experiment. The zero frequency amplitude decreases in a nonlinear way and indicates a change in dynamics around 1.4 ∙ Tmelting. From that amplitude a generalized viscosity can be derived which is a measure of local stress correlations on next-neighbour distances. The derived generalized longitudinal viscosity shows a changing slope at the same temperature range. At this temperature the freezing out of degrees of freedom for structural relaxation upon cooling sets in which can be understood as a precursor towards the solid state. That crossover in dynamics of liquid aluminium shows the same signatures as previously observed in liquid rubidium and lead, indicating an universal character. PMID:26465204

  14. Preparation of 232Th Target by Molecule Plating

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>For the cross section measurement of the 232Th(α, 2n)234U reaction, thorium targets plated on the aluminium foil with 2 and 8 μm thickness are required. It was demanded that the mass thickness of the

  15. Uranium and thorium behavior at aluminium floating-zone refining

    International Nuclear Information System (INIS)

    Uranium and thorium behaviour during aluminium refining by crystallization from the melt is ascertained. Measurements of of uranium and thorium radioactive impurities content in high-purity aluminiumn samples using the surface α-activity method are carried out. The content of the given impurities happened to be less than 1 x 10-7 mass.%. Such purity satisfies the requirements to materials applied in the low background 71Ge detection system of gallium-germanium solar neutrino detector

  16. Work Hardening and Mechanical Anisotropy of Aluminium Sheets and Profiles

    OpenAIRE

    Ryen, Øyvind

    2003-01-01

    The processing of aluminium alloys from casting to end product is associated with a large number of metallurgical phenomena. In order to further improve and optimise process routes and alloys, a thorough understanding of the thermomechanical treatments by experimental observations and physically based modelling is necessary.In part A of this thesis the work hardening behaviour of non-heat treatable alloys is followed up to large strains. The evolution in strength, microstructure and texture d...

  17. Fatigue Strength of Friction Stir Welded Joints in Aluminium

    OpenAIRE

    Ericsson, Mats

    2005-01-01

    Solid state Friction stir welding (FSW) is of major interest in the welding of aluminium since it improves the joint properties. Many applications where Al-alloys are used are subject to varying load conditions, making fatigue failure a critical issue. In the scope of this thesis, the fatigue performance of friction stir welded AlMgSi-alloy 6082 has been investigated. Static and dynamic properties of different joint configurations and welds produced with varying process parameters have been d...

  18. Aluminium extrusion investigated by theory, experiment and FEM-analysis

    OpenAIRE

    Khorasani, Sepinood Torabzadeh

    2015-01-01

    The process of aluminium extrusion has important influence in metal forming industry because of its ability to produce profiles with different shapes, sizes and complicated geometries. The required extrusion load is depending on the process parameters such as the flow stress of the billet material, velocity field, strain rate distribution, and thermal conditions within extrusion. These conditions are so important for industries, and interesting for academia, that research has been...

  19. Melting Transition of Small Aluminium Clusters Al11-20

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; ZHANG Feng-Shou; ZHU Zhi-Yuan

    2007-01-01

    Heat capacities of small aluminium clusters Al11-20 are investigated using MD simulation with empirical manybody Gupta potential. The heat capacities of some clusters Al11, Al12, Al13 and Al19 show well-defined peaks while the heat capacities of Al15-18 indicate a gradual melting transition. The spectra of isomers obtained by quenches along the MD trajectory give good interpretation for those results.

  20. Establishment of integrated information displays in aluminium surfaces using nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan; Hansen, Hans Nørgaard; Bladt, Henrik H.;

    2006-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in aluminium that can be penetrated by light. This work has resulted in a patent describing how to obtain this effect by material removal in local areas in a solid material. The idea behind an invisible display ...... micromachining with ultra-short pulses, selective etching combined with anodizing, and electrochemical machining....

  1. Texture development during recrystallization of aluminium containing large particles

    DEFF Research Database (Denmark)

    Juul Jensen, Dorte; Hansen, Niels; Humphreys, F. J.

    1985-01-01

    The recrystallization process in heavily deformed commercially pure aluminium containing large intermetallic particles was studied by in situ neutron diffraction texture measurements and various microscopical techniques including texture measurements in local areas and simultaneous determination of...... size and orientation of individual grains. The formation and growth of recrystallization nuclei at the particles and in the matrix were examined by correlating the measured change in texture to the observed change in microstructure. It was found that prolific nucleation of grains having a wide spread...

  2. Load carrying capacity analysis of materials for aluminium rims

    OpenAIRE

    Fajdiga, Matija; Čižman, Jure

    2015-01-01

    In this contribution we present an experimental simulation of the fatique strength of clamped aluminium rims. This is supported by numerical modelling using the Finite Element Method (FEM), which was used for stress-strain analysis of a model representing a clamped detail during bendings. The design and analysis of the model are made simultaneously on an integrated computer controlled test rig for testing the fatique strength of clamped parts subjected to bending. The simulation is evaluated ...

  3. Fabrication and characterisation of uranium, molybdenum, chromium, niobium and aluminium

    International Nuclear Information System (INIS)

    This paper describes fabrication of binary uranium alloys by melting and casting. The following alloys with nominal composition were obtained by melting in the vacuum furnace: uranium with niobium contents from 0.5%- 4.0% and uranium with molybdenum contents from 0.4% - 1.2%. Uranium alloys with chromium content from 0.4% - 1.2% and uranium alloy with 0.12% of aluminium were obtained by vacuum induction furnace (electric arc melting)

  4. State diagram of copper-aluminium alloys after neutron irradiation

    International Nuclear Information System (INIS)

    It is ascertained that under reactor irradiation of copper-aluminium alloys (18.0-31.2 at% of Al) radiation-induced phase transformations occur, alpha-phase is decomposed into two ones with alpha'-phase precipitation, in gamma2-phase separate regions of its high-temperature disordered modification (gamma1-phase) are formed. Thermal stability of precipitations is investigated, regions of their existence are defined on the state diagram

  5. Study of twist boundaries in aluminium. Structure and intergranular diffusion

    International Nuclear Information System (INIS)

    This research thesis addresses the study of grain boundaries in oriented crystals, and more particularly the systematic calculation of intergranular structures and energies of twist boundaries of <001> axis in aluminium, the determination of intergranular diffusion coefficients of zinc in a set of twist bi-crystals of same axis encompassing a whole range of disorientations, and the search for a correlation between these experimental results and calculated structures

  6. Hole quality and burr reduction in drilling aluminium sheets

    DEFF Research Database (Denmark)

    Pilny, Lukas; De Chiffre, Leonardo; Piska, Miroslav;

    2011-01-01

    Optimization of the metal drilling process requires creation of minimum amount of burrs and uniform appearance of the drilled holes. In this paper, an experimental investigation was performed on 2 mm sheets of wrought aluminium alloy Al99.7Mg0.5Cu-H24, using 1.6 and 2 mm diameter drills. Cutting ...... drilled holes was fulfilled as well as high productivity achieved. Such optimized process results in a noticeable production cost reduction....

  7. METAL MATRIX COMPOSITES BASED ON ALUMINIUM LITHIUM AND SILICON CARBIDE

    OpenAIRE

    White, J.; Hughes, I; Willis, T.; Jordan, R.

    1987-01-01

    The present study tests the feasibility of producing metal matrix composites based on aluminium-lithium alloys. The first step in this process has been to produce an MMC based on 8090 with SiC. This has been successfully produced by Alcan International using the "Osprey" spray deposition process. The raw billets have been processed initially by extrusion. The tensile properties of this material have been determined and the strength compares favourably with DC cast alloys. Modulus is improved ...

  8. Noncontact ultrasonic thickness measurements of thin aluminium sheet

    International Nuclear Information System (INIS)

    A method has been described for the noncontact ultrasonic thickness measurements of thin aluminium sheets, using a Q-switched ruby laser generation concentric with an annular electro-magnetic acoustic transducer (EMAT) detection to imitate pulse-echo system. The detected waveforms were analyzed with the cut-off frequences of the higher order lamb modes. The results show in a good egreement with micrometer measurements within 2% discrepancy. (authors). 22 refs, 6 figs

  9. Oblique Impact of Projectile on Thin Aluminium Plates

    Directory of Open Access Journals (Sweden)

    W.U. Khan

    2003-04-01

    Full Text Available Experiments were performed, wherein cylindrical projectiles made of hardened steel were impacted on commercially available aluminium plates at different angles. Projectiles were of 12.8 mm diameter and plates were of 0.81 mm, 1.52mm and 1.91mm thicknesses. Based on the experimental results, an analytical model has been developed to predict the residual velocity of the projectile and the ballistic limit of the plate.

  10. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    OpenAIRE

    Ma D; Guo M; Zhang M

    2013-01-01

    Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC), a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate...

  11. Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

    OpenAIRE

    Sinou, Jean-Jacques; Macquaire, Bruno

    2003-01-01

    International audience For a car manufacturer, reducing the weight of vehicles is an obvious aim. Replacing steel by aluminium moves towards that goal. Unfortunately, aluminium's stamping numerical simulation results are not yet as reliable as those of steel. Punch-strength and spring-back phenomena are not correctly described. This study on aluminium validates the behaviour law Hill 48 quadratic yield criterion with both isotropic and kinematic hardening. It is based on the yield surface ...

  12. Subgrain Growth, Recovery Kinetics and Nucleation of Recrystallization of Cold Deformed Aluminium Alloys

    OpenAIRE

    Bunkholt, Sindre

    2013-01-01

    Phenomena related to annealing of aluminium alloys are among the least understood in aluminium metallurgy but very important for industrial thermo-mechanical processing i.e. deformation and annealing. Physical models are used to predict recovery and recrystallization behaviour, and associated material properties, industrially. However, alloy development, e.g. to incorporate more recycled aluminium, has shown that current softening models are not satisfactory. Thus, improvements do require a b...

  13. Selected properties of the aluminium alloy base composites reinforced with intermetallic particles

    OpenAIRE

    M. Adamiak

    2005-01-01

    Purpose: The main aim of this work is to investigate two types of intermetallics TiAl and Ti3Al as reinforcement and their influence on selected properties and microstructure of aluminium matrix composites.Design/methodology/approach: Aluminium matrix composites were produced employing the atomised aluminium alloy AA6061 as metal matrix, when as reinforcement TiAl and Ti3Al intermetallics particles were used. The powders were cold pressed and then hot extruded. To evaluate the effect of mecha...

  14. Electrodeposition of aluminium film on P90 Li-Al alloy as protective coating against corrosion

    OpenAIRE

    U. Bardi; Caporali, S; M. Craig; A. Giorgetti; Perissi, I; Nicholls, J. R.

    2009-01-01

    In this paper we report on the electrodeposition of thin aluminium layers on P90 lithium–aluminium alloy at room temperature from a chloroaluminate ionic liquid (1-butyl-3-methyl imidazolium heptachloroaluminate [BMIm]Al2Cl7). We found that the treatment of the P90 sample's surface is a key point to obtain good quality coatings. On freshly mechanically polished surfaces, thin (about 24 µm), homogeneous and dense aluminium layers were obtained at 10 µm h− 1 deposition rate. F...

  15. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    OpenAIRE

    Mold, M; Shardlow, E; Exley, C.

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, pote...

  16. Lewis acid fragmentation of a lithium aryloxide cage: generation of new heterometallic aluminium-lithium species.

    Science.gov (United States)

    Muñoz, Ma Teresa; Urbaneja, Carmen; Temprado, Manuel; Mosquera, Marta E G; Cuenca, Tomás

    2011-11-14

    Heterometallic aluminium-lithium species were prepared by the fragmentation reaction of the hexametallic cage compound [Li{2,6-(MeO)(2)C(6)H(3)O}](6) (1) with alkyl aluminium derivatives. Depending on the aluminium precursor, the species formed present different nuclearities in the solid state as shown by single crystal X-ray analysis. Spectroscopic and computational studies have been performed to study the nuclearity of the synthesized compounds in solution.

  17. The Effect of Thickness of Aluminium Films on Optical Reflectance

    Directory of Open Access Journals (Sweden)

    Robert Lugolole

    2015-01-01

    Full Text Available In Uganda and Africa at large, up to 90% of the total energy used for food preparation and water pasteurization is from fossil fuels particularly firewood and kerosene which pollute the environment, yet there is abundant solar energy throughout the year, which could also be used. Uganda is abundantly rich in clay minerals such as ball clay, kaolin, feldspar, and quartz from which ceramic substrates were developed. Aluminium films of different thicknesses were deposited on different substrates in the diffusion pump microprocessor vacuum coater (Edwards AUTO 306. The optical reflectance of the aluminium films was obtained using a spectrophotometer (SolidSpec-3700/DUV-UV-VIS-NIR at various wave lengths. The analysis of the results of the study revealed that the optical reflectance of the aluminium films was above 50% and increased with increasing film thickness and wavelength. Thus, this method can be used to produce reflector systems in the technology of solar cooking and other appliances which use solar energy.

  18. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    DEFF Research Database (Denmark)

    Aggerbeck, Martin

    The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions of this ......The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions...... described magnetron sputtered Al-Ti coatings showed that 13 wt. % titanium and more improved the corrosion resistance at pH 13.5 and this was further improved by heat treatment, especially at 400 °C and more. The improved corrosion properties were ascribed to structural relaxation, decreased galvanic...... potential differences in the microstructure, and protection from the network of the Al3Ti phases precipitated during the heat treatment. Laser surface cladding of aluminium containing up to 20 wt. % Ti6Al4V were studied focusing on the microstructure and the alkaline corrosion properties. Due...

  19. Analysis of Orthogonal Cutting of Aluminium-based Composites

    Directory of Open Access Journals (Sweden)

    P. Ravinder Reddy

    2002-10-01

    Full Text Available A turning test on aluminium-based metal-matrix composites (MMCs (aluminium-30% silicon carbide was performed with K-20 carbide tool material and wear patterns and the wear land growth rates were analysed to evaluate the wear characteristics and to classify the relationship between the physical (mechanical properties and the flank wear of cutting tools. The study was also extended to the machining aspects and the width of cuts on MMCs and the influence of various cutting parameters. The experiments were conducted to measure the temperature along the cutting tool edge using thermocouple at various cutting speeds, and depth of cuts, keeping the feed rate constant while turning with K-20 carbide cutting tool. The finite-element method was used to simulate the orthogonal cutting of aluminium-based MMCs. The heat generation at the chip-tool interface, frictional heat generation at the tool flank, and the heat generation at the work tool interface were calculated analytically and imposed as boundary conditions. The analysis of the steady-state heat transfer was carried out and the temperature distribution at cutting edge, shear zone, and interface regions have been reported.

  20. Modelling of detonation cellular structure in aluminium suspensions

    Science.gov (United States)

    Briand, A.; Veyssiere, B.; Khasainov, B. A.

    2010-12-01

    Heterogeneous detonations involving aluminium suspensions have been studied for many years for industrial safety policies, and for military and propulsion applications. Owing to their weak detonability and to the lack of available experimental results on the detonation cellular structure, numerical simulations provide a convenient way to improve the knowledge of such detonations. One major difficulty arising in numerical study of heterogeneous detonations involving suspensions of aluminium particles in oxidizing atmospheres is the modelling of aluminium combustion. Our previous two-step model provided results on the effect on the detonation cellular structure of particle diameter and characteristic chemical lengths. In this study, a hybrid model is incorporated in the numerical code EFAE, combining both kinetic and diffusion regimes in parallel. This more realistic model provides good agreement with the previous two-step model and confirms the correlations found between the detonation cell width, and particle diameter and characteristic lengths. Moreover, the linear dependence found between the detonation cell width and the induction length remains valid with the hybrid model.

  1. Aluminium localization in root tips of the aluminium-accumulating plant species buckwheat (Fagopyrum esculentum Moench).

    Science.gov (United States)

    Klug, Benjamin; Specht, André; Horst, Walter J

    2011-11-01

    Aluminium (Al) uptake and transport in the root tip of buckwheat is not yet completely understood. For localization of Al in root tips, fluorescent dyes and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) were compared. The staining of Al with morin is an appropriate means to study qualitatively the radial distribution along the root tip axis of Al which is complexed by oxalate and citrate in buckwheat roots. The results compare well with the distribution of total Al determined by LA-ICP-MS which could be reliably calibrated to compare with Al contents by conventional total Al determination using graphite furnace atomic absorption spectrometry. The Al localization in root cross-sections along the root tip showed that in buckwheat Al is highly mobile in the radial direction. The root apex predominantly accumulated Al in the cortex. The subapical root section showed a homogenous Al distribution across the whole section. In the following root section Al was located particularly in the pericycle and the xylem parenchyma cells. With further increasing distance from the root apex Al could be detected only in individual xylem vessels. The results support the view that the 10 mm apical root tip is the main site of Al uptake into the symplast of the cortex, while the subapical 10-20 mm zone is the main site of xylem loading through the pericycle and xylem parenchyma cells. Progress in the better molecular understanding of Al transport in buckwheat will depend on the consideration of the tissue specificity of Al transport and complexation.

  2. Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

    Science.gov (United States)

    Yang, Mei; Jiang, Lixin; Huang, Huiping; Zeng, Shengbo; Qiu, Fen; Yu, Miao; Li, Xiaorong; Wei, Sheng

    2014-01-01

    Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg), fried twisted cruller (median, 466.0 mg/kg), shell (median, 107.1 mg/kg). The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake). But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week) than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

  3. Neuroprotective effect of Allium cepa L. in aluminium chloride induced neurotoxicity.

    Science.gov (United States)

    Singh, Tanveer; Goel, Rajesh Kumar

    2015-07-01

    The present study was envisaged to investigate the neuroprotective potential of Allium cepa (A. cepa) in aluminium chloride induced neurotoxicity. Aluminium chloride (50 mg/kg/day) was administered orally in mice supplemented with different doses of A. cepa hydroethanolic extract for a period of 60 days. Various behavioural, biochemical and histopathological parameters were estimated in aluminium exposed animals. Chronic aluminium administration resulted in significant motor incoordination and memory deficits, which were also endorsed biochemically as there was increased oxidative stress as well as elevated acetylcholinesterase (AChE) and aluminium levels in the brain. Supplementation with A. cepa in aluminium exposed animals significantly improved muscle coordination and memory deficits as well as reduced oxidative stress, AChE and decreased abnormal aluminium deposition in the brain. Histopathologically, there was marked deterioration visualized as decreased vacuolated cytoplasm as well as decreased pyramidal cells in the hippocampal area of mice brain which were found to be reversed with A. cepa supplementation. Administration of BADGE (PPARγ antagonist) in aluminium exposed animals reversed the neuroprotective potential of A. cepa as assessed with various behavioural, biochemical, neurochemical and histopathological estimations. In conclusion, finding of this study suggested significant neuroprotective potential of A. cepa in aluminium induced neurotoxicity. Further, the role of PPARγ receptor agonism has also been suggested as a putative neuroprotective mechanism of A. cepa, which needs further studies for confirmation.

  4. Determination of aluminium contents in selected food samples by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Food and food products are the main sources of Aluminium entering the human body. In order to know aluminium contents in food and food products, selected 26 samples from local market were analyzed by instrumental neutron activation analysis (INAA) using reactor neutrons and high resolution gamma-ray spectrometry. INAA using 1,779 keV γ-ray of 28Al (2.24 min) was used for aluminium concentrations in the range of 33-529 mg kg-1. Two NIST standard reference materials (SRMs) and two IAEA reference materials (RMs) were analyzed by INAA for quantification of aluminium as a part of method validation. (author)

  5. Low temperature oxidation of niobium alloy with silicon-aluminium coating

    International Nuclear Information System (INIS)

    Using the gravimetry methods heat resistance of niobium-titanium-aluminium alloy in the air and at 700 deg C in the initial state and when it is protected by silicide-aluminium coatings (with variable content of aluminium) is investigated. Using X-ray diffraction and micro X-ray diffraction analyses, mechanisms of the alloy oxidation and the coating protective effect are studied. The role of aluminium in the formation of coatings is analyzed and according to bend tests the plasticity of the coatings is evaluated

  6. Antiproton production target of the AA

    CERN Multimedia

    Photographic Service

    1980-01-01

    The target rods were initially of tungsten, later of iridium. Diameters were around 3 mm and the lengths 60-110 mm. The rod is embedded in graphite, pressed into an aluminium body with cooling fins for forced air cooling. The 26 GeV proton beam from the PS was focused to the dimension of the rod. To aim precisely at its centre, the target was fitted with a scintillator screen, with circles at every 5 mm radius. Both scintillator and target had to stand pulses of 1.4E13 protons every 4.8 s, without interruption for many months.

  7. Aluminium nitride: from the powder to the substrate. Le nitrure d'aluminium: de la poudre au substrat

    Energy Technology Data Exchange (ETDEWEB)

    Jarrige, J. (Lab. de Ceramiques Nouvelles, Limoges (France)); Mexmain, J. (Lab. de Ceramiques Nouvelles, Limoges (France)); Oumaloul, M. (Lab. de Ceramiques Nouvelles, Limoges (France)); Bachelard, R. (CRRA ELF ATOCHEM, Pierre Benite (France)); Disson, J.P. (CRRA ELF ATOCHEM, Pierre Benite (France))

    1993-04-01

    The aluminium nitride is a material which should replace alumina or beryllia as substrate for power electronic applications. The powder, prepared by carbothermal nitridation, is dispersed in a butanone-2-ethanol azeotrop solvent with a phosphate ester. Electrical conductivity, sedimentation, viscosity have been used to determine which phenomena take place in the defloculation of the suspension. The stability of AlN suspensions is due mainly to an electrostatic mechanism, with a steric contribution. The aluminium nitride tape-casting slip has been sintered at 1850 C in a nitrogen atmosphere. Removing of the binder and plasticizer can be performed in the same oven at 650 C, due to their nature and low concentration. The thermal conductivity of the substrates has been measured and is in the 160 to 200 W/m.K range. (orig.).

  8. APPLICATION OF LASER ADDITIVE MANUFACTURING TO PRODUCE DIES FOR ALUMINIUM HIGH PRESSURE DIE-CASTING#

    Directory of Open Access Journals (Sweden)

    M.F.V.T. Pereira

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: A number of laser additive manufacturing (LAM technologies can produce fully-dense metal components that potentially offer opportunities to apply the technology in die or mould making (known as rapid tooling. From these LAM technologies, three were selected for evaluation of their suitability as die cavity inserts in the manufacture of high pressure die-casting (HPDC dies. Apart from comparing the different LAM inserts with one another, their performance was also compared with components manufactured in a standard hot work steel. In the HPDC process, the die is unique to each component to be produced. Die cavities in particular are subjected to demanding conditions, such as cyclic heating caused by the introduction of molten aluminium at over 650°C, followed by cooling in water-based die release medium at temperatures around 25°C. Besides cyclic heating, the die cavities are also exposed to pressures exceeding 1500 MPa during the injection of molten aluminium into the cavities. This application of LAM, therefore, poses extreme challenges to the technology. The results of this study confirmed that the metals used in some of the LAM technologies did indeed meet the demanding requirements of the current application, and can lead to significant time- and cost-saving during product or process developments. Based on these findings, a number of recommendations are made for users interested in the application of LAM to produce die cavities.

    AFRIKAANSE OPSOMMING: ’n Aantal laser laagvervaardigingstegnologieë (LLV tegnolgieë is in staat om volledig digte metaalkomponente te lewer, wat tot gevolg het dat hierdie tegnologie potensieel vir vormingsmatrys- of gietmatrysvervaardiging gebruik kan word (bekend as snelgereedskap. Drie van hierdie LLV tegnologieë is gekies vir evaluasie van hulle geskiktheid as gietvorminsetsels tydens die vervaardiging van gietmatryse vir hoë druk matrysgiet (HDMG. Benewens die onderlinge

  9. Radiation effects in the aluminium alloys irradiated with neutrons

    International Nuclear Information System (INIS)

    Full text: Materials of fuel elements for water cooled nuclear reactors are exposed to simultaneous action of an ionizing radiation, temperature and yields of water radiolysis. In particular, irradiation by fast neutrons (En> 0.1 MeV) in research reactors influences mainly the mechanical properties of aluminium alloys, increasing their strength and reducing the plasticity. Radiation can essentially affect the stability of the heat-generating assembly material, changing its structure state. The structure change may also be the result of post-radiation ageing. This paper presents the results of studying the influence of reactor neutrons (research reactor of INP AS RU) on microstructure, electrical characteristics and length changes of SAV-1 and AMG-2 aluminium alloys used in nuclear industry. These alloys are low-alloyed solid solutions and intermetallic phases of CuAl2, Mg2Si, CuMgAl2, CuMg4Al6, Al2Mg2 in an equilibrium state. Samples were cut with orientation in 111 crystallographic axis in the shape of disks with the diameter d= 15 mm and thickness h= 3 mm for the metallographic analysis, and rods with the length of 40 mm and width d = 5 mm for measuring specific electrical resistance and linear dimension changes prior and after irradiations. For precise measurements the sample surfaces were mechanically handled and polished in a chemical solution, and then washed out in the distilled water and ethanol. Further samples, were put into the aluminum container and irradiated in a vertical channel of the reactor to fluencies 1018, 1019, 1020 n/cm2. The relative elongation (extension) δ was calculated as the measured length ratio of the non-irradiated and irradiated sample: δ=L0/L1x100%. Determination of element composition and the metallographic analysis of studied samples were done at the X-ray microanalyzer 'Jeol' JSM 5910 IV. Specific resistance (ρ) values were measures with four probe technique by compensation method at the direct voltage. The sample lengths

  10. MicroRNA-106b-25 cluster targets β-TRCP2, increases the expression of Snail and enhances cell migration and invasion in H1299 (non small cell lung cancer) cells.

    Science.gov (United States)

    Savita, Udainiya; Karunagaran, Devarajan

    2013-05-17

    Lung cancer causes high mortality without a declining trend and non small cell lung cancer represents 85% of all pulmonary carcinomas. MicroRNAs (miRNAs) serve as fine regulators of proliferation, migration, invasion/metastasis and angiogenesis of normal and cancer cells. Using TargetScan6.2, we predicted that the ubiquitin ligase, β-TRCP2, could be a target for two of the constituent miRNAs of the miR-106b-25 cluster (miR-106b and miR-93). We generated a stable clone of miR-106b-25 cluster (CL) or the empty vector (EV) in H1299 (non small cell lung cancer) cells. The expression of β-TRCP2 mRNA was significantly lower in CL than that in EV cells. Transient expression of miR-93 but not antimiR-93 decreased the expression of β-TRCP2 mRNA in H1299 cells. β-TRCP2-3'UTR reporter assay revealed that its activity in CL cells was only 60% of that in EV cells. Snail protein expression was higher in CL than that in EV cells and H1299 cells exhibited an increase in the expression of Snail upon transient transfection with miR-93. miR-106b-25 cluster-induced migration of CL measured by scratch assay was more than that in EV cells and no significant difference in migration was observed between antimiR-93-transfected H1299 cells and the corresponding control-oligo-transfected cells. miR-106b-25 cluster-induced migration of CL cells was again confirmed in a Boyden chamber assay without the matrigel. CL cells were more invasive than EV cells when assessed using Boyden chambers with matrigel but there were no significant changes in the cell viabilities between EV and CL cells. Colony formation assay revealed that the CL cells formed more number of colonies than EV cells but they were smaller in size than those formed by EV cells. The supernatant from CL cells was more effective than that from EV cells in inducing tube formation in endothelial cells. Taken together, our data indicate that miR-106b-25 cluster may play an important role in the metastasis of human non-small cell

  11. Studi Eksperimen Pengaruh Variasi Dimensi Cil Dalam (Internal Chill Terhadap Cacat Penyusutan (Shrinkage Pada Pengecoran Aluminium 6061

    Directory of Open Access Journals (Sweden)

    Nurhadi Ginanjar Kusuma

    2014-09-01

    Full Text Available Aluminium merupakan salah satu material yang semakin banyak dimanfaatkan terutama pada industri komponen mesin. Cacat pada hasil cor sangat dihindari karena akan berpengaruh pada kualitas hasil yang merubah dimensi dan sifat mekanik dari benda hasil cor. Shrinkage merupakan cacat yang terjadi karena perbedaan kecepatan pendinginan pada benda cor. Penambahan variasi ukuran dimensi cil dalam (internal chill bertujuan untuk menganalisa pengaruh perubahan dimensi terhadap cacat shrinkage pada pengecoran. Penelitian pembuatan benda coran dilakukan dengan menggunakan bahan coran aluminium 6061 dengan menggunakan metode pengecoran pasir. Sistem saluran yang digunakan menggunakan ketentuan AFS. Jenis saluran yang digunakan adalah horizontal parting-line, serta pasir cetak dengan komposisi pasir silica 89%, bentonit 7,5%, dan air 3,5%. Hasil penelitian menunjukkan pengaruh penggunaan dimensi internal chill terhadap prosentase jumlah cacat shrinkage dengan diameter 15, 20, dan 25 secara berurutan sebesar 3,82, 1,28, dan 1,01%. Penggunaan variasi dimensi internal chill pada pengecoran benda yang semakin diperbesar dapat berfungsi dengan baik serta menggeser lokasi cacat penyusutan menjauhi internal chill. Grafik yang didapatkan dari pengukuran pada internal chill diameter 25 mm (daerah yang mengalami prosentase cacat terkecil memiliki kemampuan menyerap panas lebih baik daripada diameter 15 dan 20 mm.

  12. Organic acid metabolism and root excretion of malate in wheat cultivars under aluminium stress.

    Science.gov (United States)

    de Andrade, Leide Rovênia Miranda; Ikeda, Motoki; do Amaral, Lourdes Isabel Velho; Ishizuka, Junji

    2011-01-01

    The effects of aluminium (Al) on the metabolism of organic acids synthesised via nonphotosynthetic carbon fixation in the roots and on malate exudation were investigated in Al-tolerant Shirosanjyaku (SH) and Al-sensitive Chikushikomugi (CK) wheat cultivars labelled with bicarbonate-(14)C. Aluminum triggered the excretion of (14)C into the solution, especially in the SH that excreted 2.5 times more (14)C than the CK. The loss of radioactivity (about 10%) into the solution represented a small drain in the (14)C reserve found in the roots. In the organic acid fraction within the roots, malate contained the greatest amount of (14)C, and this amount decreased rapidly with time in both cultivars. The disappearance of radioactivity in the malate resulted from metabolism and translocation rather than to root efflux. Aluminium decreased the malate concentrations in roots of both cultivars. The Al-sensitive cultivar had higher concentrations of malate regardless of the presence of Al. It was therefore assumed that the decrease of malate concentration in roots under Al stress did not result from the decline in malate synthesis but due to an increase in malate decomposition. This response was interpreted as the result of the Al-induced stress and not as the cause of a differential Al-tolerance between the wheat cultivars. An important component of the differential Al tolerance between SH and CK is the greater ability of the Al-tolerant cultivar to excrete malate from the roots, which is independent of its internal concentration in the roots.

  13. Reinforced aluminium conductor for cryogenic applications

    International Nuclear Information System (INIS)

    Extreme purity aluminum has very attractive electrical properties at temperatures below 25 K which makes it competitive with conventional superconductors for cryogenic applications. Besides its inherently low density, its resistivity decreases by several orders of magnitude over its room temperature value thus making it suitable for use in lightweight high current density devices. This paper describes the fabrication of a 99.999% aluminum conductor reinforced by a powder metallurgy (P/M) processed Al-Fe-Ce alloy. Long continuous lengths of composite conductors consisting of 1, 4 and 19 Al filaments have been produced by streamline die hot extrusion and cold working by conventional wire drawing or cold hydrostatic extrusion. Microstructural observations and some limited electrical resistivity and mechanical property data are presented along with an analysis of the contamination of high purity Al conductors by diffusion during annealing

  14. Study of X-ray emission in aluminium z-pinches; Etude de l'emission X dans les plasmas d'aluminium de type Z-pinch

    Energy Technology Data Exchange (ETDEWEB)

    Rosch, R. [CEA/DAM-Ile de France, Dept. de Conception et Realisation des Experimentations (DCRE), 91 - Bruyeres-le-Chatel (France)]|[Paris-11 Univ., 91 - Orsay (France)

    1999-07-01

    Previous experiments, at 0.1. TX level, have shown that stability and x-ray emission of fast Z-pinches, could be strongly increased by imploding an aluminium vapor jet onto a very thin coaxial wire. We present here first results of an aluminium Z-pinch, using a similar liner, but at mega-ampere level. The pinch is driven by AMBIORIX high-power facility, a 2 TW,0.5 {omega}, 2 MA, 50 ns pulse-line generator. We study the effect of an aluminium wire and its diameter (20-50 {mu}m) on the implosion dynamics, on x-ray yield on MHD stability of the column at stagnation. Analysis of A1 jet on A1 wire shots demonstrates that x-ray yield due to emission processes in the H- and He- like ionization stages (i.e. the K-shell) is significantly enhanced, relative to that of A1 jet only ones. The wire also leads to better symmetry of the implosion, and to better reproducibility of shots. X-ray signals exhibit two similar pulses, 10 ns in width, 15 ns spaced. To discern spectral origin of both pulses, experiments are realized with stainless steel wire (25 {mu}m in diameter). Results show that liner and wire radial simultaneously and contribute to both pulses. Analysis of a typical A1 jet on A1 wire shot, using detailed collisional-radiative equilibrium (CRE) model is also given in this thesis. View o the pinch at stagnation as a cola-dense core surrounded by a hot-low density corona reproduces all features of the X-ray data. (author)

  15. (4-Hydroxy-2,5-dimethylphenylphenylmethanone

    Directory of Open Access Journals (Sweden)

    Rodolfo Moreno-Fuquen

    2009-11-01

    Full Text Available The title compound, C15H14O2, was obtained by Friedel–Crafts acylation between 2,5-dimethylphenol and benzoyl chloride in the presence of aluminium chloride as a catalyst. The dihedral angle between the benzene rings is 61.95 (4°. In the crystal, O—H...O hydrogen bonding and C—H...O weak interactions lead to polymeric C(6, C(8 and C(11 chains along the a, b and c-axis directions, respectively.

  16. Studies on aluminium leaching from cookware in tea and coffee and estimation of aluminium content in toothpaste, baking powder and paan masala.

    Science.gov (United States)

    Rajwanshi, P; Singh, V; Gupta, M K; Kumari, V; Shrivastav, R; Ramanamurthy, M; Dass, S

    1997-01-30

    Studies were conducted in order to assess the level of aluminium (Al) in samples of Indian tea, coffee, toothpaste, paan masala (mouth freshener) and baking powder. Leaching of Al from cookware while preparing tea and coffee was also studied. Experiments were also conducted to study the sequential leaching of Al from cookware by preparing tea and coffee in the presence of standard size Al sheets (coupons). A small amount of Al was found to have leached from coupons during preparation of tea. Tea leaves, were found to be a rich source of Al and a maximum of 2.2% Al is extracted in tea infusions. Coffee powder on the other hand was not found to be a rich source of Al. Baking powder was found to be a rich source of Al and 1 kg of cake prepared with 1-3 teaspoon of baking powder may contain 2-12.7 mg of Al in each serving (25 g). Toothpaste also contains a significant quantity of Al, more so, when packed in Al tubes. Ingestion pattern of Al from these items by humans is also discussed. PMID:9092078

  17. Formation of aluminium, aluminium nitride and nitrogen clusters via laser ablation of nano aluminium nitride. Laser Desorption Ionisation and Matrix-Assisted Laser Desorption Ionisation Time-of-Flight Mass Spectrometry.

    Science.gov (United States)

    Panyala, Nagender Reddy; Prysiazhnyi, Vadym; Slavíček, Pavel; Černák, Mirko; Havel, Josef

    2011-06-30

    Laser Desorption Ionisation (LDI) and Matrix-Assisted Laser Desorption Ionisation (MALDI) Time-of-Flight Mass Spectrometry (TOFMS) were used to study the pulsed laser ablation of aluminium nitride (AlN) nano powder. The formation of Al(m)(+) (m=1-3), N(n)(+) (n=4, 5), AlN(n)(+) (n=1-5, 19, 21), Al(m)N(+) (m=2-3), Al(3)N(2)(+), Al(9)N(n)(+) (n=5, 7, 9, 11 and 15), Al(11)N(n)(+) (n=4, 6, 10, 12, 19, 21, 23, and 25), and Al(13)N(n)(+) (n=25, 31, 32, 33, 34, 35, and 36) clusters was detected in positive ion mode. Similarly, Al(m)(-) (m=1-3), AlN(n)(-) (n=1-3, 5), Al(m)N(-) (n=2, 3), Al(2)N(n)(-) (n=2-4, 28, 30), N(n)(-) (n=2, 3), Al(4)N(7)(-) Al(8)N(n)(-) (n=1-6), and Al(13)N(n)(-) (n=9, 18, 20, 22, 24, 26, 28, 33, 35, 37, 39, 41 and 43) clusters were observed in negative ion mode. The formation of the stoichiometric Al(10) N(10) cluster was shown to be of low abundance. On the contrary, the laser ablation of nano-AlN led mainly to the formation of nitrogen-rich Al(m)N(n) clusters in both negative and positive ion mode. The stoichiometry of the Al(m)N(n) clusters was determined via isotopic envelope analysis and computer modelling.

  18. Formation of aluminium, aluminium nitride and nitrogen clusters via laser ablation of nano aluminium nitride. Laser Desorption Ionisation and Matrix-Assisted Laser Desorption Ionisation Time-of-Flight Mass Spectrometry.

    Science.gov (United States)

    Panyala, Nagender Reddy; Prysiazhnyi, Vadym; Slavíček, Pavel; Černák, Mirko; Havel, Josef

    2011-06-30

    Laser Desorption Ionisation (LDI) and Matrix-Assisted Laser Desorption Ionisation (MALDI) Time-of-Flight Mass Spectrometry (TOFMS) were used to study the pulsed laser ablation of aluminium nitride (AlN) nano powder. The formation of Al(m)(+) (m=1-3), N(n)(+) (n=4, 5), AlN(n)(+) (n=1-5, 19, 21), Al(m)N(+) (m=2-3), Al(3)N(2)(+), Al(9)N(n)(+) (n=5, 7, 9, 11 and 15), Al(11)N(n)(+) (n=4, 6, 10, 12, 19, 21, 23, and 25), and Al(13)N(n)(+) (n=25, 31, 32, 33, 34, 35, and 36) clusters was detected in positive ion mode. Similarly, Al(m)(-) (m=1-3), AlN(n)(-) (n=1-3, 5), Al(m)N(-) (n=2, 3), Al(2)N(n)(-) (n=2-4, 28, 30), N(n)(-) (n=2, 3), Al(4)N(7)(-) Al(8)N(n)(-) (n=1-6), and Al(13)N(n)(-) (n=9, 18, 20, 22, 24, 26, 28, 33, 35, 37, 39, 41 and 43) clusters were observed in negative ion mode. The formation of the stoichiometric Al(10) N(10) cluster was shown to be of low abundance. On the contrary, the laser ablation of nano-AlN led mainly to the formation of nitrogen-rich Al(m)N(n) clusters in both negative and positive ion mode. The stoichiometry of the Al(m)N(n) clusters was determined via isotopic envelope analysis and computer modelling. PMID:21598328

  19. The Macro-Adjustment Policies on China’s Aluminium Industry

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>In recent years, China’s aluminium industry has developed rapidly with considerable expansion of the production scale. Presently, China’s aluminum production capacity has taken a quarter of the world total, and China has become the largest aluminium producer in the world, However, such large scaled expan-

  20. Aluminium based adjuvants and their effects on mitochondria and lysosomes of phagocytosing cells.

    Science.gov (United States)

    Ohlsson, Lars; Exley, Christopher; Darabi, Anna; Sandén, Emma; Siesjö, Peter; Eriksson, Håkan

    2013-11-01

    Aluminium oxyhydroxide, Al(OH)3 is one of few compounds approved as an adjuvant in human vaccines. However, the mechanism behind its immune stimulating properties is still poorly understood. In vitro co-culture of an aluminium adjuvant and the human monocytic cell line THP-1 resulted in reduced cell proliferation. Inhibition occurred at concentrations of adjuvant several times lower than would be found at the injection site using a vaccine formulation containing an aluminium adjuvant. Based on evaluation of the mitochondrial membrane potential, THP-1 cells showed no mitochondrial rupture after co-culture with the aluminium adjuvant, instead an increase in mitochondrial activity was seen. The THP-1 cells are phagocytosing cells and after co-culture with the aluminium adjuvant the phagosomal pathway was obstructed. Primary or early phagosomes mature into phagolysosomes with an internal pH of 4.5 - 5 and carry a wide variety of hydrolysing enzymes. Co-culture with the aluminium adjuvant yielded a reduced level of acidic vesicles and cathepsin L activity, a proteolytic enzyme of the phagolysosomes, was almost completely inhibited. THP-1 cells are an appropriate in vitro model in order to investigate the mechanism behind the induction of a phagocytosing antigen presenting cell into an inflammatory cell by aluminium adjuvants. Much information will be gained by investigating the phagosomal pathway and what occurs inside the phagosomes and to elucidate the ultimate fate of phagocytosed aluminium particles.

  1. The effect of aluminium chlorhydrate on sweat gland activity in cattle.

    Science.gov (United States)

    Rees-Jones, A M; Jenkinson, D M

    1978-03-01

    Topical application of aluminium chlorhydrate had no appreciable antiperspirant action on the epitrichial glands of cattle. There was no evidence of penetration of the salt into the dermis or of any change in the morphology of the glands. It is probable that the antiperspirant activity of aluminium chlorhydrate in the human axilla, is only on the atrichial glands. PMID:632617

  2. Aluminium in an ocean general circulation model compared with the West Atlantic Geotraces cruises

    NARCIS (Netherlands)

    van Hulten, M. M. P.; Sterl, A.; Tagliabue, A.; Dutay, J. -C.; Gehlen, M.; de Baar, H. J. W.; Middag, R.

    2013-01-01

    A model of aluminium has been developed and implemented in an Ocean General Circulation Model (NEMO-PISCES). In the model, aluminium enters the ocean by means of dust deposition. The internal oceanic processes are described by advection, mixing and reversible scavenging. The model has been evaluated

  3. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain. PMID:27515230

  4. The role of magnesium in the electrochemical behaviour of 5XXX aluminium-magnesium alloys

    NARCIS (Netherlands)

    Flores Ramirez, J.R.

    2006-01-01

    An investigation concerning the effects of magnesium on the intergranular corrosion susceptibility of AA5XXX aluminium alloys was carried out. In the present work, magnesium is found to be highly mobile in the bulk metal as well as in the aluminium oxide. This mobility is also found to be dependent

  5. Design of an aluminium bicycle path integrated in a steel bridge

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Burggraaf, H.G.

    2007-01-01

    This paper describes the design of the aluminium structure of a bicycle path which is mounted on an existing steel brige. The benefits of aluminium, being low self weight, freedom in design obtained by extrusion and good corrosion resistance were maximal utilized. One of the main drawbacks of alumin

  6. Microstructure and interfaces of a reaction coating on aluminium alloys by laser processing

    NARCIS (Netherlands)

    Zhou, X.B.; Hosson, J.Th.M. De

    1993-01-01

    This paper reports an approach to coat a ceramic layer on aluminium alloys by means of chemical reaction. The reaction product of Al2O3 layer of 100 µm in thickness has been formed using a powder mixture of silicon oxide and aluminium by laser processing. It turns out that the large amount of heat f

  7. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    Directory of Open Access Journals (Sweden)

    N. S. Ahmad Zauzi

    2016-01-01

    Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

  8. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-08-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

  9. Fatigue testing of large scale details of a large size aluminium surface effect ship

    NARCIS (Netherlands)

    Dijkstra, O.D.; Vredeveldt, A.W.; Janssen, G.Th.M.; Ortmans, P.

    1998-01-01

    The paper presents the results of two large scale fatigue tests on a detail of an aluminium surface effect ship. The overall dimensions of the specimens were: length 4.8 m, height 3.2 m and width 1.5 m (equal to the main frame spacing). The specimens consist of an aluminium structure of welded plate

  10. Nouveau procédé de synthèse du nitrure d'aluminium

    OpenAIRE

    Haussonne, J.; Lostec, J.; Bertot, J.; Lostec, L.; Sadou, S.

    1993-01-01

    Les calculs thermodynamiques montrent que, même à température ambiante, l'aluminium pur peut réagir avec l'azote pour former le nitrure d'aluminium AlN. Cependant, la poudre d'aluminium pur n'existe pas : ses grains sont toujours entourés d'une couche d'alumine protectrice. De plus, dans l'hypothèse où l'on pourrait faire réagir de la poudre d'aluminium avec de l'azote, il se formerait de même une couche protectrice de nitrure d'aluminium qui empêcherait le centre des grains de réagir. S'insp...

  11. Production and some properties of Si3N4 reinforced aluminium alloy composites

    Directory of Open Access Journals (Sweden)

    Pardeep Sharma

    2015-09-01

    Full Text Available The present research work focuses on the production of aluminium (AA6082-T6 matrix composites reinforced with various weight percentage of silicon nitride particles by conventional stir casting route. The percentage of reinforcement is varied from 0 wt.% to 12 wt.% in a stage of 3%. The microstructures and mechanical properties of the fabricated aluminium matrix composites are investigated. The scanning electron microstructure images reveal the presence of Si3N4 particles in the aluminium matrix. The distribution of Si3N4 particles has also been recognized with X-ray diffraction technique. The mechanical properties such as ultimate tensile strength and hardness have improved at the cost of reduction in ductility with increase in weight percentage of silicon nitride particulates in the aluminium metal matrix. The density and porosity of the composites also show an increasing trend with increase in volume fraction of Si3N4 particles in the aluminium matrix.

  12. Experimental Study on the Shock Absorption Performance of Combined Aluminium Honeycombs under Impact Loading

    Directory of Open Access Journals (Sweden)

    Lei Cao

    2015-01-01

    Full Text Available Shock absorption characteristics of combined aluminium honeycomb structures were studied experimentally. In the experiments, a testing platform was design to compare the shock absorption level of different honeycomb specimens quantitatively. The shock response curves of six test points mounted on the platform were recorded with acceleration sensors when the buffer was impacted by a bullet driven by high pressure gas. The maximum acceleration values in time domain and in specifically spectral domain were obtained based on spectral analysis. Comparing the data of combined aluminium honeycomb buffer and single aluminium honeycomb buffer, conclusion can be obtained that shock absorbing characteristic of combined aluminium honeycomb buffer is better. Furthermore, compression properties of three kinds of buffers were tested under quasi-static state. The energy absorption parameters were calculated. The results show suitable combined aluminium honeycomb buffer can smooth the stress and lower the energy applied to the testing platform.

  13. TEM microstructure investigations of aluminium alloys used for laser alloying

    Directory of Open Access Journals (Sweden)

    K. Labisz

    2012-12-01

    Full Text Available Purpose: In this paper there are presented results of Transmission Electron Microscope investigation concerning the structure of the AlSi7Cu4 cast aluminium alloy using for alloying and remelting with the high power diode laser (HPDL. There are also presented the results of the thermo-derivative analysis performed using the UMSA (Universal Metallurgical Simulator and Analyser device, allowing to determine the specific points of the solidifying alloy, what is helpful for phase determination occurred in this alloy. In this work especially the changes of the precipitation type, size and shape were determined.Design/methodology/approach: The investigations were performed using electron microscopy for the microstructure and phases determination. By mind of the transmission electron microscopy, especially selected area diffraction method appliance it was possible to determine the phases occurred in the alloy in the as cast state. The morphology and size of the Mg2Si was also possible to determine as well the lattice parameters for this phase.Findings: : The reason of this work was also to present the laser treatment technology, which will be used for further alloying and remelting with ceramic powders – especially carbides and oxides. Particularly the overview will be directed on the laser power to achieve good layer hardness for protection of this hot work tool steel from losing their work stability and to make the tool surface more resistant to action in external conditions. The structure of the surface laser tray changes in a way, that there are very high roughness of the surface zone and the flatness or geometry changes in an important manner, crucial for further investigation.Research limitations/implications: The aluminium samples were examined metallographically using transmission electron microscope with different image techniques.Practical implications: Developing of new technology with appliance of Al alloys, High Power Diode Laser and

  14. Slip lines in scandium and lithium containing aluminium alloys

    International Nuclear Information System (INIS)

    Intensive slip lines in cold rolled sheets of scandium or lithium containing aluminium base alloys are under study. Slip lines are shown to be the places of concentrated shear strain which arise due to the occurrence of secondary δ'(Al3Li) and Al3Sc particles completely coherent to the matrix. The formation of slip lines has a detrimental effect on cold rolled sheet mechanical properties after heat hardening. To avoid the appearance of slip lines it is necessary to roll sheets with low reductions in area and to choose appropriate conditions of intermediate heat treatments. 5 refs., 5 figs., 2 tabs

  15. Regularities in aluminium and indium chemisorption on chelating polymeric sorbents

    International Nuclear Information System (INIS)

    Complexation properties of synthesized polymer chelate sorbents: substituted of polystyrene-azo-pyrocatechol are investigated and correlations between pK'OH of functional groups of sorbents as well as pH50 values of chelation and constants of stability (lgKstab) are established for studying regularities of effect of structure and acid-base properties of functional groups of sorbents on the parameters of Al3+ and In3+ chemical sorption. Established correlations make it possible to predict the physicochemical parameters of sorbents and sorption of metal ions with the aim of separation and concentration of aluminium and indium micro account from the objects of different origin

  16. Skin telangiectasia in workers of an aluminium processing plant.

    Science.gov (United States)

    Balić, J; Kansky, A

    1988-01-01

    Telangiectases were detected in 57 (46.7%) of 122 workers employed at the electrolysis department of the aluminium plant Lozovac/Sibenik, Yugoslavia. Of 116 workers employed in the smeltery of the same plant, telangiectases were observed in 19 persons (16.4%) and in a group of 121 public transportation workers from Sibenik 15 men (12.4%) displayed enlarged blood vessels. Statistical evaluation revealed the difference in number between workers showing telangiectases engaged in electrolysis and the other two samples to be significant. It may be assumed that telangiectases were caused by hydrogen fluoride and other fluorides. Further clinical parameters, as well as working conditions, are reviewed.

  17. Modeling of recrystallization texture of aluminium: symmetric and asymmetric rolling

    Science.gov (United States)

    Wierzbanowski, K.; Kotra, M.; Wronski, M.; Sztwiertnia, K.; Wronski, S.; Lodini, A.

    2015-04-01

    In some metallic materials the dominating recrystallization mechanism can be described by the oriented growth behaviour. Phenomenological laws state that in selected materials only these nuclei grow intensively which have a given misorientation relation with the deformed matrix. This description is frequently verified in f.c.c. metals and generally reported misorientations correspond approximately to 400 rotation around the axis. Basing on the above ideas the recrystallization model, including the compromise condition, was formulated and applied to the study of recrystallization textures of rolled polycrystalline aluminium.

  18. Physical model of aluminium refining process in URC-7000

    Directory of Open Access Journals (Sweden)

    M. Saternus

    2009-07-01

    Full Text Available The paper presents short characteristics of the most frequently used reactors for the continuous refining of aluminium and its alloys. Refining depends on the flow rate of refining gas. It influences the shape and size of gas bubbles. So the physical model was created to determine the level of gas bubble dispersion in liquids. Schemes of gas dispersion in liquid metal were presented taking into consideration that the gas flow rate is changing from 2 to 30 dm3/min. The range selection of the flow rate of refining gas value for five patterns of the dispersion (no dispersion, minimum, intimate, uniform and overdispersion was also done.

  19. Interface reaction in aluminium matrix composite at laser welding

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Interface reaction of SiCw/6061Al aluminium matrix composite subjected to laser welding was studied. It is pointed out that the main reason for bad weldability of the material is concerned with the interface reaction during the welding. Effects of welding parameters on interface reaction were also investigated. The results show that the interface bonding state can be improved by laser beam, and the main welding parameter affecting the strength of weld is laser output power. The smaller the output power, the lower the extent of interface reaction and the better the mechanical properties.

  20. Design considerations for HFQ® hot stamped aluminium structural panels

    Directory of Open Access Journals (Sweden)

    Foster Alistair

    2015-01-01

    Full Text Available HFQ is a deep drawing process for alloyed aluminium sheet that can be used to produce complex-stamped forms while maintaining the high-strength of 6xxx and 7xxx alloys. By adopting a strategy to design for HFQ at the platform level, designers can reduce part count (thereby reducing cost and weight, reduce gauge (thereby reducing weight, and improve part packaging. Two simple design examples are given to assist designers in evolving traditionally formed panel designs to HFQ formed solutions. Example features are used to illustrate the effect of geometry, thickness and strength on the final structural component.

  1. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    OpenAIRE

    Aggerbeck, Martin; Ambat, Rajan

    2014-01-01

    I dette projekt blev muligheden for at designe aluminiumsbaserede coatings undersøgt med fokus på hvordan den kemiske sammensætning og overfladens beskaffenhed påvirker den visuelle fremtoning og de basiske korrosionsegenskaber med titan anvendt som det primære legeringselement. De primære resultater og diskussioner fra dette arbejde præsenteres i form af i bilag som fire artikelmanuskripter indsendt til publikation i tidsskrifter. Anvendelsen af aluminium er bred, fra transportmidler, bygnin...

  2. Optically Designed Anodised Aluminium Surfaces: Microstructural and Electrochemical Aspects

    DEFF Research Database (Denmark)

    Gudla, Visweswara Chakravarthy

    under high frequency anodising, highly reflecting, bright and glossy white anodised aluminium surfaces were generated for the first time. Further, these white anodised surfaces were conventionally dyed to generate new appearances based on pastel colours. The work presented in this thesis is mainly......-13). The outcome of the work is presented in the last chapter (Chapter 15). The results from white anodising of the Al surfaces, which is the primary goal of this thesis and also the generation of a new set of pastel coloured anodised surfaces is presented. The optical characterization of these white anodised...

  3. The effect of atmospheric corona treatment on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.;

    2010-01-01

    The effect of atmospheric corona discharge on AM 050 aluminium surface was investigated using electrochemical polarization, SEM-EDX, FIB-SEM. and XPS. The corona treatment was performed with varying time (1, 5, and 15 min) in atmospheric air. A 200 nm oxide layer was generated on AA1050 after...... the 15 min air corona treatment. A significant reduction in anodic and cathodic reactivities was observed starting from 1 min exposure, which further decreased with prolonged exposure (15 min) and after delayed testing (after 30 days). The reduction in surface reactivity is due to the formation...

  4. Multi-element study in aluminium by activation analysis technique

    International Nuclear Information System (INIS)

    The instrumental activation analysis is a technique relatively quickly that help to know the elemental composition of materials. It is used mainly in the trace elements determination but in the case of major elements it is necessary to make some considerations as the different nuclear reactions carried out due to the neutron flux is a mixture of thermal and fast neutrons. This could be interpreted for the presence and or erroneous quantification about some elements. In this work, is described the way in which was analyzed a container piece with approximately a 85% of aluminium. The elements Zn, Mn, Sb, Ga, Cu, Cl and Sm were determined. (Author)

  5. Determination of phosphorus in hypereutectic aluminium-silicon alloys.

    Science.gov (United States)

    Mukai, K

    1972-04-01

    A reproducible method is described for determination of small amounts of phosphorus (from 0.0005% to 0.02%) in hypereutectic aluminium-silicon complex alloys. The method permits the separate determination of phosphorus in acid-soluble and acid-insoluble fractions. Phosphomolybdate is extracted with n-butanol-chloroform solvent mixture and back-extracted with a btannous chloride reducing solution. The phosphorus content of a sample cut into small pieces decreases during storage; loss of phosphorus is negligible on acid dissolution under oxidizing conditions. PMID:18961077

  6. Bone histoquantitative findings and histochemical staining reactions for aluminium in chronic renal failure patients treated with haemodialysis fluids containing high and low concentrations of aluminium.

    OpenAIRE

    McClure, J; Fazzalari, N L; Fassett, R G; Pugsley, D. J.

    1983-01-01

    A total of 112 undecalcified bone biopsies from 67 patients under treatment for chronic renal failure by maintenance haemodialysis was available for retrospective study. The patients were divided into three groups. Group I (15 cases) had been dialysed for the majority of the time in their own homes with a fluid containing a low concentration of aluminium. Group II (28 cases) had been dialysed exclusively in hospital (prior to 1978) with a fluid containing a high concentration of aluminium and...

  7. Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

    Energy Technology Data Exchange (ETDEWEB)

    Manes, A., E-mail: andrea.manes@polimi.it; Pagani, M.; Saponara, M.; Mombelli, D.; Mapelli, C.; Giglio, M.

    2014-07-01

    Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details.

  8. Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

    International Nuclear Information System (INIS)

    Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details

  9. 铝合金芯高导电率铝绞线标准解读%A Reading of High Conductivity Aluminium Conductor Aluminium Alloy Reinforced Standard

    Institute of Scientific and Technical Information of China (English)

    万建成; 董玉明; 刘龙

    2014-01-01

    To implement the engineering philosophy of security, reliability, reasonable economy, advanced technology and environmental friendliness, company standard of State Grid, 《High Conductivity Aluminium Conductor Aluminium Alloy Reinforced》, has been finished. A detailed reading about the technical approaches, basic principle and announcements of high conductivity aluminium conductor aluminium alloy reinforced standard is given by combining corresponding research results. The implementation of the standard provides important basis to guide the engineering application of high conductivity aluminium conductor aluminium alloy reinforced and will promote the upgrading of conductors for overhead transmission lines.%贯彻安全可靠、经济合理、技术先进、环境友好的技术原则,完成国家电网公司企业标准《铝合金芯高导电率铝绞线》的制定工作。结合铝合金芯高导电率铝绞线相应研究成果,解读主要条款的编制思路、基本原理以及注意事项。该标准的实施为指导铝合金芯高导电率铝绞线工程应用提供重要依据,并将促进架空输电线路用导线的更新换代。

  10. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Horsewell, Andy; Sommer, W. F.;

    1986-01-01

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg(AlMg3) and Al-1.1%Mg-0.5%Si(Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-100°C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) sho...... higher than in the pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure...

  11. Aluminium sensitized spectrofluorimetric determination of fluoroquinolones in milk samples coupled with salting-out assisted liquid-liquid ultrasonic extraction

    Science.gov (United States)

    Xia, Qinghai; Yang, Yaling; Liu, Mousheng

    2012-10-01

    An aluminium sensitized spectrofluorimetric method coupled with salting-out assisted liquid-liquid ultrasonic extraction for the determination of four widely used fluoroquinolones (FQs) namely norfloxacin (NOR), ofloxacin (OFL), ciprofloxacin (CIP) and gatifloxacin (GAT) in bovine raw milk was described. The analytical procedure involves the fluorescence sensitization of aluminium (Al3+) by complexation with FQs, salting-out assisted liquid-liquid ultrasonic extraction (SALLUE), followed by spectrofluorometry. The influence of several parameters on the extraction (the salt species, the amount of salt, pH, temperature and phase volume ratio) was investigated. Under optimized experimental conditions, the detection limits of the method in milk varied from 0.009 μg/mL for NOR to 0.016 μg/mL for GAT (signal-to-noise ratio (S/N) = 3). The relative standard deviations (RSD) values were found to be relatively low (0.54-2.48% for four compounds). The calibration graph was linear from 0.015 to 2.25 μg/mL with coefficient of determinations not less than 0.9974. The methodology developed was applied to the determination of FQs in bovine raw milk samples. The main advantage of this method is simple, accurate and green. The method showed promising applications for analyzing polar analytes especially polar drugs in various sample matrices.

  12. Development of Al-TiC Alloys Using Powder Metallurgy as Grain Refiners for Aluminium and Its Alloys

    Directory of Open Access Journals (Sweden)

    Abdel-Nasser .M. Omran

    2014-07-01

    Full Text Available Al-Ti-C master alloys have been widely investigated for many years as grain refiner for aluminium and its alloys. In this work, the Al-Ti-C master alloys are synthesized using powder metallurgy technique through the mixing of aluminium and TiC powders with different TiC contents 3.75 (3, 5(4, 6.25(5 and 7.5(6 Wt% TiC(Wt% Ti. The mixing powders with different contents of TiC were pressed in cylinder shape. The pressed specimens were sintered from 450 oC in a tube furnace under argon atmosphere for 2 hrs. The produced alloys before and after sintering are examined using SEM, EDX and XRD. The results indicate that, the Al-TiC alloy containing fine TiC particles dispersed in all matrix was successfully prepared. The prepared Al-TiC alloys with different contents of TiC were evaluated using the KBI test mold as grain refiner for pure aluminum and its alloys. The results indicate that the prepared Al-TiC master alloy is high grain refining efficiency for pure aluminum and its alloys.

  13. Mechanism of hierarchical porosity development in MFI zeolites by desilication: the role of aluminium as a pore-directing agent.

    Science.gov (United States)

    Groen, Johan C; Peffer, Louk A A; Moulijn, Jacob A; Pérez-Ramírez, Javier

    2005-08-19

    The role of the concentration and the nature of aluminium in the creation of hierarchical porosity in both commercial and synthesized MFI zeolites have been investigated through controlled mesoporosity development by desilication in alkaline medium. Framework aluminium controls the process of framework silicon extraction and makes desilication selective towards intracrystalline mesopore formation. An optimal molar Si/Al ratio in the range 25-50 has been identified; this leads to an optimal mesoporosity centred around 10 nm and mesopore surface areas of up to 235 m(2) g(-1) while preserving the intrinsic crystalline and acidic properties. At lower framework Si/Al ratios the relatively high Al content inhibits Si extraction and hardly any mesopores are created, while in highly siliceous ZSM-5 unselective extraction of framework Si induces formation of large pores. The existence of framework Al sites in different T positions that are more or less susceptible to the alkaline treatment, and the occurrence of re-alumination, are tentative explanations for the remarkable behaviour of Al in the desilication process. The presence of substantial extra framework Al, obtained by steam treatment, inhibits Si extraction and related mesopore formation; this is attributed to re-alumination of the extraframework Al species during the alkaline treatment. Removal of extraframework Al species by mild oxalic acid treatment restores susceptibility to desilication, which is accompanied by formation of larger mesopores due to the enhanced Si/Al ratio in the acid-treated zeolite.

  14. Effect of calcium sulfates on the early hydration of calcium sulfoaluminate cement and the stability of embedded aluminium

    International Nuclear Information System (INIS)

    Conventional Portland cement-based systems have been considered unsuitable for immobilising nuclear wastes containing reactive metals, such as aluminium, due to the high pH of the pore solution (usually around 12.5) and free moisture. On the contrary, calcium sulfo-aluminate cement (CSA) produces a lower pH (10.5-12) environment and has an excellent water binding capability as a result of the formation of its main hydration product, ettringite. Therefore, it offers a good potential to immobilise aluminium. However, the pore solution pH and ettringite formation depend largely on the raw materials used to formulate the CSA, which is usually a blend of 75%-85% of CSA clinker and 15-25% of calcium sulfate (in the form of gypsum or anhydrite). In this paper, it was found that, compared to anhydrite, gypsum (15% wt of the blend) demonstrated the highest reduction in the corrosion of embedded Al, possibly due to its lower initial pH (around 10.5) and self-desiccating nature at the early stage of hydration. Whilst the CSA/anhydrite had a higher Al corrosion rate, the initial set was more acceptable than CSA/gypsum. Nonetheless, overall, it was concluded that CSA with gypsum (15% wt) should be considered as a base formulation for the encapsulation of Al waste. The unfavorable rapid set and high heat generation, however, demonstrated that modifications are required, potentially by using mineral additions. (authors)

  15. Manipulation of stored charge in anodic aluminium oxide/SiO2 dielectric stacks by the use of pulsed anodisation

    Science.gov (United States)

    Lu, Zhong; Ouyang, Zi; Grant, Nicholas; Wan, Yimao; Yan, Di; Lennon, Alison

    2016-02-01

    A method of fabricating anodic aluminium oxide (AAO) with the capability of manipulating its stored charge is reported. This method involves the use of a pulsed current source to anodise aluminium layers instead of the typically used constant current/voltage source, with the test structures experiencing positive and negative cycles periodically. By tuning the positive cycle percentage, it is demonstrated that the effective stored charge density can be manipulated in a range from -5.2 × 1011 to 2.5 × 1012 q/cm2 when the AAO is formed over a 12 nm SiO2 layer. An investigation of the stored charge distribution in the dielectric stacks indicates a positive fixed charge at the SiO2/Si interface, a negative fixed charge at the AAO/SiO2 interface and a positive bulk charge within the AAO layer. The effective stored charge density and interface states were found to be affected by annealing conditions and it is suggested that oxygen annealing can reduce the bulk positive charge while post-metallisation anneal is most effective in reducing silicon interface defects. Charge manipulation using pulsed anodisation is shown to reduce carrier recombination on boron-diffused silicon surfaces highlighting the potential of the process to be used to tune the electrical properties of dielectric layers so that they can reduce surface recombination on silicon surfaces having different dopant polarity and concentrations.

  16. Comparative estimation of soil and plant pollution in the impact area of air emissions from an aluminium plant after technogenic load reduction.

    Science.gov (United States)

    Evdokimova, Galina A; Mozgova, Natalya P

    2015-01-01

    The work provides a comparative analysis of changes in soil properties in the last 10-13 years along the pollution gradient of air emissions from Kandalaksha aluminium plant in connection with the reduction of their volume. The content of the priority pollutant fluorine (F) in atmospheric precipitation and in the organic horizon of soil in the plant impact zone significantly decreased in 2011-2013 compared to 2001. The aluminium concentrations reduced only in immediate proximity to the plant (2 km). The fluorine, calcium (Ca) and magnesium (Mg) concentrations are higher in liquid phase compared to solid phase thus these elements can migrated to greater distances from the pollution source (up to 15-20 km). Silicon (Si), aluminium (Al), iron (Fe) and phosphorus (P) can be found only in solid phases and in fall-out within the 5 km. The acidity of soil litter reduced by 2 pH units in the proximity to the plot within the 2 km. The zone of maximum soil contamination decreased from 2.5 km to 1.5 km from the emission source, the zones of heavy and moderate pollution reduced by 5 km in connection with the reduction of pollutant emissions in the plant. A high correlation between the fluorine concentrations in vegetables and litter was found. Higher fluorine concentrations in the soil result in its accumulation in plants. Mosses accumulate fluorine most intensively.

  17. Aluminium surface treatment with ceramic phases using diode laser

    Science.gov (United States)

    Labisz, K.; Tański, T.; Brytan, Z.; Pakieła, W.; Wiśniowski, M.

    2016-07-01

    Ceramic particles powder feeding into surface layer of engineering metal alloy is a well-known and widely used technique. New approach into the topic is to obtain finely distributed nano-sized particles involved in the aluminium matrix using the traditional laser technology. In this paper are presented results of microstructure investigation of cast aluminium-silicon-copper alloys surface layer after heat treatment and alloying with ceramic carbides of WC and ZrO2 using high-power diode laser. The surface layer was specially prepared for the reason of reducing the reflectivity, which is the main problem in the up-to-date metal matrix composites production. With scanning electron microscopy, it was possible to determine the deformation process and distribution of WC and ZrO2 ceramic powder phase. Structure of the surface after laser treatment changes, revealing three zones—remelting zone, heat-affected zone and transition zone placed over the Al substrate. The structural changes of ceramic powder, its distribution and morphology as well as microstructure of the matrix material influence on functional properties, especially wear resistance and hardness of the achieved layer, were investigated.

  18. Geopolymerisation of fly ashes with waste aluminium anodising etching solutions.

    Science.gov (United States)

    Ogundiran, M B; Nugteren, H W; Witkamp, G J

    2016-10-01

    Combined management of coal combustion fly ash and waste aluminium anodising etching solutions using geopolymerisation presents economic and environmental benefits. The possibility of using waste aluminium anodising etching solution (AES) as activator to produce fly ash geopolymers in place of the commonly used silicate solutions was explored in this study. Geopolymerisation capacities of five European fly ashes with AES and the leaching of elements from their corresponding geopolymers were studied. Conventional commercial potassium silicate activator-based geopolymers were used as a reference. The geopolymers produced were subjected to physical, mechanical and leaching tests. The leaching of elements was tested on 28 days cured and crushed geopolymers using NEN 12457-4, NEN 7375, SPLP and TCLP leaching tests. After 28 days ambient curing, the geopolymers based on the etching solution activator showed compressive strength values between 51 and 84 MPa, whereas the commercial potassium silicate based geopolymers gave compressive strength values between 89 and 115 MPa. Based on the regulatory limits currently associated with the used leaching tests, all except one of the produced geopolymers (with above threshold leaching of As and Se) passed the recommended limits. The AES-geopolymer geopolymers demonstrated excellent compressive strength, although less than geopolymers made from commercial activator. Additionally, they demonstrated low element leaching potentials and therefore can be suitable for use in construction works.

  19. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    Directory of Open Access Journals (Sweden)

    Hamilta de Oliveira Santos

    2005-06-01

    Full Text Available Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken from a billet of an experimental alloy (alloy 1 and were subsequently hot-rolled and cold-rolled (height reduction, 72% and 70%, respectively. The other used samples, alloys 2 and 3, were taken from cylinders liners. The results from the Laue camera showed texture just in the axial direction of alloy 3. The pole figures also indicated the presence of a typical low intensity deformation texture, especially for alloy 3. The spray formed microstructure, which is very fine, hinders the Al-Si texture formation during mechanical work.

  20. Cancellous bone homograft storage with aluminium-polyethylene bags.

    Science.gov (United States)

    Meana, A; Martinez, R; Cañal, P; Arriaga, M J; Román, F San; Llames, S; Orós, C; Moreno, A; Fernandez, C

    2006-01-01

    In order to transport and cryopreserve human tissues, it is essential to have an easy-to-use recipient where tissues can be kept in sterile conditions. Here we show the results obtained by using Macopharma's tissue freezing bags, an aluminium-polyethylene multilayer bag, in our tissue bank of the Centro Comunitario de Sangre y Tejidos de Asturias. Five hundred and twenty-seven cancellous bone homografts were obtained from hospitals located 120 km around our Bank. The homografts were submitted to bacteriological controls and sent to our bank in these bags. They were stored at -70 degrees C and sent in dry ice to about 50 hospitals, where the tissue was bacteriologically controlled and grafted. Furthermore, the behaviour of these bags at -140 degrees C (vapour nitrogen) or -196 degrees C (liquid nitrogen) was tested. Our results indicate that Macopharma aluminium-polyethylene bags are suitable for the transporting and cryopreserving of cancellous bone homografts. These bags could also be used for keeping tissues in nitrogen containers.

  1. A 3D printed superconducting aluminium microwave cavity

    Science.gov (United States)

    Creedon, Daniel L.; Goryachev, Maxim; Kostylev, Nikita; Sercombe, Timothy B.; Tobar, Michael E.

    2016-07-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals, in particular, has found a number of applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Although many techniques are used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a microwave cavity (resonant frequencies 9.9 and 11.2 GHz) 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable with the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum electrodynamics experiments. The result is achieved even with a very large concentration of non-superconducting silicon in the alloy of 12.18%, compared with Al-6061, which has between 0.4% and 0.8%. Our results may pave the way for the possibility of 3D printing superconducting cavity configurations that are otherwise impossible to machine.

  2. A 3D Printed Superconducting Aluminium Microwave Cavity

    CERN Document Server

    Creedon, Daniel L; Kostylev, Nikita; Sercombe, Tim; Tobar, Michael E

    2016-01-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals in particular has found a number of novel applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Whilst many techniques can be used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a resonant microwave cavity 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable to the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum...

  3. Modelling of semi-liquid aluminium flow in extrusion

    Directory of Open Access Journals (Sweden)

    G. Skorulski

    2007-04-01

    Full Text Available characterizing by low cost. The significant results may be quickly applying using theory of probability. The way of modelling the deformation mechanisms during extrusion of aluminium alloys in semi - liquid phase, the way of preparing samples and experimental technique has been analysed in the following work. On the ground of received results (i.e. registrations of consecutive process steps the grid of the flow velocity vectors on a flat sample surface was done. It allowed to draw conclusions which one of the basic deformation mechanisms is dominant in particular stage of the process. The technique of measurement has been shown as well. Experiments are made using plasticine and rape oil as a substiute materials. Some kind of different variants have been investigated. To ensure that such model experiments provide useful information it is essential to select model materials and prepare samples that would exhibit (preferably at room temperature similar behaviour and similar deformation mechanisms as those present during the actual deformation process of aluminium alloys in a semi-liquid state. In particular the FLS, SS and PDS mechanisms should be adequately reproduced.

  4. The Effect of Dynamic Compression on the Evolution of Microstructure in Aluminium and its Alloys

    Directory of Open Access Journals (Sweden)

    Leszczyńska-Madet B.

    2013-12-01

    Full Text Available W pracy przedstawiono wyniki badań mikrostruktury i wybranych właściwości polikrystalicznego aluminium i jego stopów: AlMg5, AlCu4Zr0.5, AlZn6Mg2.5CuZr ściskanych dynamicznie za pomocą młota spadowego. Próbki odkształcano w zakresie odkształceń rzeczywistych = 0-0.62 z prędkością odkształcenia z zakresu 1.77-6.06x102 s-1. Na tak odkształconych materiałach przeprowadzono pomiar mikrotwardości oraz badania mikrostruktury przy zastosowaniu transmisyjnego mikrosko- pu elektronowego (TEM i mikroskopu świetlnego (LM, dodatkowo przeprowadzono pomiar dezorientacji w mikroobszarach metodą linii Kikuchiego przy zastosowaniu oprogramowania KILIN. Cechą charakterystyczną mikrostruktury badanych materiałów były licznie obserwowane pasma i pasma ścinania. Wyniki uzyskane przy zastosowaniu transmisyjnego mikroskopu elektronowego dowiodły występowania licznych mikropasm i mikro- pasm ścinania, które w zależności od materiału przebiegały na tle różnych układów dyslokacyjnych. Obserwowane mikropasma wykazywały dużą dezorientację względem osnowy. Stwierdzono wzajemnie przecinanie się mikropasm. W zakresie wyższych wartości odkształcenia, mikropasma wypełniały niemal całą objętość próbek. Zaobserwowano zależność zmniejszania się średniej szerokości i mikropasm wraz ze wzrostem wielkości odkształcenia i prędkości odkształcenia. Praca miała na celu określenie wpływu prędkości odkształcenia (1.77x10' - 6.06xl02s_1 na możliwość rozdrobnienia mikrostruktury polikrystalicznego aluminium A199.5 i jego stopów (AlMg5, AlCu4Zr0.5, AlZn6Mg2.5CuZr odkształcanych w procesie dynamicznego ściskania za pomocą młota spadowego.

  5. Effect of aluminium on in vitro rooting of birch (Betula pendula Roth. and poplar (Populus tremula L. x P. alba L. microcuttings

    Directory of Open Access Journals (Sweden)

    Krystyna Bojarczuk

    2014-02-01

    Full Text Available Poplar (Populus tremula L. x P. alba L. and birch (Betula pendula Roth. microcuttings obtained from in vitro cultures on media with aluminium (Al+ or without aluminium (Al- were rooted in perlite saturated with a liquid 1/4 MS medium. Aluminium was added to the rooting medium in the form of aluminium sulphate or aluminium chloride. In the control, i.e. in the medium without aluminium, Al+ and Al- shoots usually developed similarly. Addition of aluminium to the rooting medium had a negative effect on the development of adventitious roots. Poplar and birch shoots obtained from cultures on media with aluminium (AI+ were distinguished by a greater tolerance of aluminium in the medium than shoots obtained from cultures on media without aluminium (A1-.

  6. Nouveau procédé de synthèse du nitrure d'aluminium

    Science.gov (United States)

    Haussonne, J. M.; Lostec, J.; Bertot, J. P.; Lostec, L.; Sadou, S.

    1993-04-01

    Thermodynamic considerations show that, even at room temperature, pure aluminium can react with nitrogen to form the aluminium nitride AlN. However, pure aluminium does not exist: it is always surrounded by an alumina shell that protects the metal from further reactions. Furthermore, in the hypothesis where one has been able to make aluminium react with nitrogen, an aluminium nitride shell will protect as well the metal core from further oxidation. Prompted by the Lanxide process allowing to form Al/Al2O3 composites, we have mixed aluminium powders with lithium salts, and easily synthesized pure aluminium nitride by heating the mixed powders in nitrogen at temperatures ranging from 800 to 1200 °C. Starting from aluminium powders with a specific area ranging from 0.3 to 4 m^2/g, we have been able to produce aluminium nitride with specific are ranging from 1 to 20 m^2/g. Mixed with Y203-CaO and sintered at 1720 °C in N2, we obtained AIN ceramics owning 92% density and 160 W/m.K thermal conductivity. Les calculs thermodynamiques montrent que, même à température ambiante, l'aluminium pur peut réagir avec l'azote pour former le nitrure d'aluminium AlN. Cependant, la poudre d'aluminium pur n'existe pas : ses grains sont toujours entourés d'une couche d'alumine protectrice. De plus, dans l'hypothèse où l'on pourrait faire réagir de la poudre d'aluminium avec de l'azote, il se formerait de même une couche protectrice de nitrure d'aluminium qui empêcherait le centre des grains de réagir. S'inspirant du “procédé Lanxide” permettant de réaliser des composites Al/Al2O3, nous avons mélangé de la poudre d'aluminium avec des sels de lithium, et synthétisé du nitrure d'aluminium pur en portant ce mélange dans l'azote à une température pouvant être comprise entre 800 et 1 200 °C. Utilisant des poudres d'aluminium possédant une surface spécifique comprise entre 0,3 et 4 m^2/g, nous avons obtenu une poudre de nitrure d'aluminium avec une surface sp

  7. Ballistic behavior of boron carbide reinforced AA7075 aluminium alloy using friction stir processing–An experimental study and analytical approach

    Institute of Scientific and Technical Information of China (English)

    I. SUDHAKAR; G. MADHUSUDHAN REDDY; K. SRINIVASA RAO

    2016-01-01

    High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160μm sized boron carbide powder was procured and was reduced to 60μm and 30μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing. Ballistic performance testing as per the military standard (JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites

  8. Derivation of a water quality guideline for aluminium in marine waters.

    Science.gov (United States)

    Golding, Lisa A; Angel, Brad M; Batley, Graeme E; Apte, Simon C; Krassoi, Rick; Doyle, Chris J

    2015-01-01

    Metal risk assessment of industrialized harbors and coastal marine waters requires the application of robust water quality guidelines to determine the likelihood of biological impacts. Currently there is no such guideline available for aluminium in marine waters. A water quality guideline of 24 µg total Al/L has been developed for aluminium in marine waters based on chronic 10% inhibition or effect concentrations (IC10 or EC10) and no-observed-effect concentrations (NOECs) from 11 species (2 literature values and 9 species tested including temperate and tropical species) representing 6 taxonomic groups. The 3 most sensitive species tested were a diatom Ceratoneis closterium (formerly Nitzschia closterium; IC10 = 18 µg Al/L, 72-h growth rate inhibition) aluminium forms of aluminate (Al(OH4 (-) ) and aluminium hydroxide (Al(OH)3 (0) ) although both dissolved, and particulate aluminium contributed to toxicity in the diatom Minutocellus polymorphus and green alga Dunaliella tertiolecta. In contrast, aluminium toxicity to the green flagellate alga Tetraselmis sp. was the result of particulate aluminium only. Four species, a brown macroalga (Hormosira banksii), sea urchin embryo (Heliocidaris tuberculata), and 2 juvenile fish species (Lates calcarifer and Acanthochromis polyacanthus), were not adversely affected at the highest test concentration used.

  9. Increased absorption of aluminium from a normal dietary intake in dementia.

    Science.gov (United States)

    Roberts, N B; Clough, A; Bellia, J P; Kim, J Y

    1998-02-15

    Serum aluminium was significantly raised (p dementia including Alzheimers Disease (AD) 0.66 +/- 0.2 (mumol/l mean +/- 1 s.d.) and patients on regular aluminium hydroxide therapy 0.54 +/- 0.17, compared with healthy volunteers 0.21 +/- 0.13, although not as high as in patients with end stage renal failure on regular dialysis 0.88 +/- 0.42. The urine outputs (mumol/l mean +/- 1 s.d.) of aluminium and silicon, respectively, were also significantly increased up to 5-fold in dementia 2.89 +/- 1.78 (n = 23) and 1587 +/- 645 (n = 22) and patients on regular aluminium hydroxide therapy 5.03 +/- 2.08 (n = 8) and 998 +/- 364 (n = 21) compared with healthy volunteers 0.95 +/- 0.82 (n = 84) and 471 +/- 332 (n = 114). The increase in urine aluminium was thus associated with a similarly marked increase in the output of silicon. The increased absorption of aluminium in dementia patients is equivalent to the intestinal loading in Aludrox therapy. Also silicon appears to be important in the renal excretion of the absorbed aluminium. Whether this is a phenomenon related to the elderly or the process of dementia warrants further study.

  10. Determination of local material properties of laser beam welded aluminium-steel and aluminium-titanium compounds

    Energy Technology Data Exchange (ETDEWEB)

    Hunkel, M.; Hehl, A. von [IWT Stiftung Institut fuer Werkstofftechnik Bremen (Germany); Barr, A.

    2012-04-15

    The combination of different metallic materials, such as aluminium and steel or aluminium and titanium, by firmly bonding via laser beam welding enables the production of customised hybrid lightweight designs with enhanced properties. Both weld geometry and local material behaviour, which are responsible for the final load characteristics of the compound, are influenced by the process parameters during welding. A novel approach of coupling process, microstructure and mechanical simulation, considering the development of weld geometry and local material conditions is intended to deliver a fast and reliable method for evaluating the quasi-static strength of laser beam welded hybrid compounds. Besides the objective to promote a reduction of expensive welding experiments, the developed method can enhance the performance of hybrid structures as well as their lightweight potential for automotive and aircraft applications. The experimental determination of the local mechanical properties as the basis for the regarded simulation approach is an essential part of a running research project. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Aluminium exposure from parenteral nutrition in preterm infants and later health outcomes during childhood and adolescence.

    Science.gov (United States)

    Fewtrell, Mary S; Edmonds, Caroline J; Isaacs, Elizabeth; Bishop, Nick J; Lucas, Alan

    2011-08-01

    Aluminium is the most common metallic element, but has no known biological role. It accumulates in the body when protective gastrointestinal mechanisms are bypassed, renal function is impaired, or exposure is high - all of which apply frequently to preterm infants. Recognised clinical manifestations of aluminium toxicity include dementia, anaemia and bone disease. Parenteral nutrition (PN) solutions are liable to contamination with aluminium, particularly from acidic solutions in glass vials, notably calcium gluconate. When fed parenterally, infants retain >75% of the aluminium, with high serum, urine and tissue levels. Later health effects of neonatal intravenous aluminium exposure were investigated in a randomised trial comparing standard PN solutions with solutions specially sourced for low aluminium content. Preterm infants exposed for >10 d to standard solutions had impaired neurologic development at 18 months. At 13-15 years, subjects randomised to standard PN had lower lumbar spine bone mass; and, in non-randomised analyses, those with neonatal aluminium intake above the median had lower hip bone mass. Given the sizeable number of infants undergoing intensive care and still exposed to aluminium via PN, these findings have contemporary relevance. Until recently, little progress had been made on reducing aluminium exposure, and meeting Food and Drug Administration recommendations (<5 μg/kg per d) has been impossible in patients <50 kg using available products. Recent advice from the UK Medicines and Healthcare regulatory Authority that calcium gluconate in small volume glass containers should not be used for repeated treatment in children <18 years, including preparation of PN, is an important step towards addressing this problem.

  12. Developments in electrode materials and electrolytes for aluminium-air batteries

    OpenAIRE

    Egan, D; Ponce De Leon, Carlos; R.J.K. Wood; Jones, R. L.; Stokes, K.R.; Walsh, F. C.

    2013-01-01

    Aluminium-air cells are high-energy density (< 400 W h kg-1), primary batteries first developed in the 1960s. The review shows how the performance of the battery is influenced by the choice of materials, including the type of aluminium alloy, oxygen reduction catalyst and electrolyte type. Two continuing issues with these batteries are (a) the parasitic corrosion of the aluminium, at open-circuit and under discharge, due to the reduction of water on the anode surface and (b) the passive hydro...

  13. The aluminium content of breast tissue taken from women with breast cancer.

    Science.gov (United States)

    House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

    2013-10-01

    The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

  14. The Major Events of China’s Aluminium Industry in 2005

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>The year 2005 is seen as a turning point for China’s aluminium industry with the whole industry making losses leading to the closures, reorganization and acquisitions of the smelters. The macro-adjustment policies of the government on the aluminium industry and the industry’s operating difficulties led to the overall change of the industry, which is reflected by the strengthened position of China’s aluminium industry in the world and China’s influence on the world market is growing with the united

  15. Étude par spectrométrie auger d'alliages aluminium-cuivre liquides

    Science.gov (United States)

    Laty, P.; Joud, J. C.; Desré, P.

    1981-03-01

    Surface analysis of liquid aluminium and aluminium-copper alloys have been performed by Auger electron spectroscopy at 775°C. Experiments were carried out, in UHV chamber, on liquid droplets located in graphite crucible heated by a heat pipe. Pure aluminium has been studied in view to estimate surface contamination. For each Al-Cu alloy surface composition is calculated from the Auger spectra. Peak to peak height ratios are deduced from limited extrapolation t zero level contamination. The deduced Al enrichment of the surface is compared with thermodynamical computation based on statistical model or Gibbs' adsorption relation.

  16. Characterization of steam generated anti-corrosive oxide films on Aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2014-01-01

    Aluminium and its alloys are widely used in structural and transportation industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further...... of hexavalent chromium is strictly regulated due to its toxic nature and suspected carcinogenicity. So, it is highly imperative to develop other alternatives for chrome conversion coatings. Treatment of aluminium with natural water at elevated temperatures results in the formation of different forms...

  17. Car-Parrinello Simulation of the Aluminium Oxidation: Questioning the Role of 'Hot Adatoms'

    CERN Document Server

    Schulte, Marius

    2012-01-01

    We present Car-Parrinello molecular dynamics simulations of the initial reaction steps leading to an inert oxide layer on aluminium. The mechanism of the reaction of the aluminium surface with single oxygen molecules is analysed. After adsorption at the surface the oxygen molecules dissociate at a femtosecond timescale and the atoms are chemisorbed at the surface at a distance of several angstrom which falsifies earlier STM results. When the aluminium surface is exposed to higher oxygen pressure, a surface layer essentially consisting of threefold coordinated oxygen atoms starts to form.

  18. Influence of Aluminium on Performance of HTPB-based Aluminised PBXs

    Directory of Open Access Journals (Sweden)

    Vinay Prakash

    2004-10-01

    Full Text Available The paper describes the development of aluminised plastic-bonded explosives (PBXs based on aluminium and nitramine explosives using hydroxy-terminated polybutadiene as polymer matrix. The PBXs were processed as per standard procedures. Compositions with different formulations were prepared by varying the percentages of aluminium and RDX and their explosive properties, including velocity of detonation (VOD, peak overpressure, duration, impulse and sensitivity to different types of stimuli, were studied. The experimental and theoretical values of the VOD have been compared. It is observed that about 15 per cent aluminium content in the aluminised PBXs shows the optimum VOD.

  19. Cobalt and Nickel Nanopillars on Aluminium Substrates by Direct Current Electrodeposition Process

    Directory of Open Access Journals (Sweden)

    Santos A

    2009-01-01

    Full Text Available Abstract A fast and cost-effective technique is applied for fabricating cobalt and nickel nanopillars on aluminium substrates. By applying an electrochemical process, the aluminium oxide barrier layer is removed from the pore bottom tips of nanoporous anodic alumina templates. So, cobalt and nickel nanopillars are fabricated into these templates by DC electrodeposition. The resulting nanostructure remains on the aluminium substrate. In this way, this method could be used to fabricate a wide range of nanostructures which could be integrated in new nanodevices.

  20. Bioavailability and Toxicity of Aluminium to the Freshwater Crayfish, Pacifastacus leniusculus

    OpenAIRE

    Woodburn, Katie

    2012-01-01

    Aluminium is found in large amounts all over the world but plants and animals have no use for this metal. However, because it is everywhere, aluminium can get into animals and stops cells, tissues and organs from working properly. The aim of this thesis was to look at where aluminium goes when it is eaten by crayfish and whether it causes any damage to body systems such as the digestive system and the nervous system. Crayfish are freshwater crustaceans; they have a hard outer exoskeleton and ...