Incorporation of tv tube glass waste in aluminous porcelain

Energy Technology Data Exchange (ETDEWEB)

Holanda, J.N.F.; Santos, T.F.; Paes Junior, H.R. [Universidade Estadual do Norte Fluminense (UENF), Campos dos Goytacazes, RJ (Brazil)

2016-07-01

Full test: This work analyzes the reuse of TV tube glass waste as a method to provide alternative raw material for aluminous porcelain, through of replacement of natural sodic feldspar by up to 30 wt.%. Aluminous porcelain formulations containing TV tube glass waste were pressed and fired in air at 1300 deg C using a fast-firing cycle. Ceramic pieces were characterized by X-ray diffraction, scanning electron microscopy, linear shrinkage, apparent density, apparent porosity, water absorption, and electrical resistivity. XRD and SEM results indicated that all aluminous porcelain pieces are composed essentially of mullite, quartz, and ?-alumina embedded in a vitreous matrix. The results also showed that the aluminous porcelain pieces containing TV tube glass waste presented low water absorption values between 0.42 and 0.45 %, apparent density between 2.44 and 2.46 g/cm3, and volume electrical resistivity between 1.91 and 2.93 x 1011 ?.cm. Thus, the TV tube glass waste could be used into aluminous porcelain formulations, in the range up to 30 wt.%, as a replacement for traditional flux material (sodic feldspar). (author)

Hot corrosion of pack cementation aluminized carbon steel

International Nuclear Information System (INIS)

Waheed, A.F.; Mohamed, K.E.; Abd El-Azim, M.E.; Soliman, H.M.

1998-01-01

Low carbon steel was aluminized by the pack cementation technique at various aluminizing temperatures and times in or der to have different aluminide coatings. The aluminized specimens were sprayed at the beginning of the hot corrosion experiments with Na C 1+Na 2 SO 4 solution. The hot corrosion tests were carried out by thermal cycling at 850 degree C in air. The results were evaluated by, corrosion kinetics based on weight change measurements, scanning electron microscopy and energy dispersive X-ray analysis. It was found that the maximum corrosion resistance to this corrosive environment is achieved by aluminizing at 900 degree C for 19 h or 950 degree C for >4 h. These aliminizing conditions lead to formation of thick aluminide coatings with sufficient aluminium concentration (>15 wt%) at their outer surface necessary for continuous formation of protective Al 2 O 3 scale. The tested materials are used in protection of some components used in electric power stations (conventional or nuclear)

Characterisation of magnesium potassium phosphate cements blended with fly ash and ground granulated blast furnace slag

Energy Technology Data Exchange (ETDEWEB)

Gardner, Laura J.; Bernal, Susan A.; Walling, Samuel A.; Corkhill, Claire L.; Provis, John L.; Hyatt, Neil C., E-mail: n.c.hyatt@sheffield.ac.uk

2015-08-15

Magnesium potassium phosphate cements (MKPCs), blended with 50 wt.% fly ash (FA) or ground granulated blast furnace slag (GBFS) to reduce heat evolution, water demand and cost, were assessed using compressive strength, X-ray diffraction (XRD), scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) spectroscopy on {sup 25}Mg, {sup 27}Al, {sup 29}Si, {sup 31}P and {sup 39}K nuclei. We present the first definitive evidence that dissolution of the glassy aluminosilicate phases of both FA and GBFS occurred under the pH conditions of MKPC. In addition to the main binder phase, struvite-K, an amorphous orthophosphate phase was detected in FA/MKPC and GBFS/MKPC systems. It was postulated that an aluminium phosphate phase was formed, however, no significant Al–O–P interactions were identified. High-field NMR analysis of the GBFS/MKPC system indicated the potential formation of a potassium-aluminosilicate phase. This study demonstrates the need for further research on these binders, as both FA and GBFS are generally regarded as inert fillers within MKPC.

Chemical and Enzymatic Hydrolysis of Polyurethane/Polylactide Blends

Directory of Open Access Journals (Sweden)

Joanna Brzeska

2015-01-01

Full Text Available Polyether-esterurethanes containing synthetic poly[(R,S-3-hydroxybutyrate] (R,S-PHB and polyoxytetramethylenediol in soft segments and polyesterurethanes with poly(ε-caprolactone and poly[(R,S-3-hydroxybutyrate] were blended with poly([D,L]-lactide (PLA. The products were tested in terms of their oil and water absorption. Oil sorption tests of polyether-esterurethane revealed their higher response in comparison to polyesterurethanes. Blending of polyether-esterurethanes with PLA caused the increase of oil sorption. The highest water sorption was observed for blends of polyether-esterurethane, obtained with 10% of R,S-PHB in soft segments. The samples mass of polyurethanes and their blends were almost not changed after incubation in phosphate buffer and trypsin and lipase solutions. Nevertheless the molecular weight of polymers was significantly reduced after degradation. It was especially visible in case of incubation of samples in phosphate buffer what suggested the chemical hydrolysis of polymer chains. The changes of surface of polyurethanes and their blends, after incubation in both enzymatic solutions, indicated on enzymatic degradation, which had been started despite the lack of mass lost. Polyurethanes and their blends, contained more R,S-PHB in soft segments, were degraded faster.

Microstructure and oxidation behaviour of aluminized coating of inconel 625

International Nuclear Information System (INIS)

Khalid, F.A.; Hussain, N.; Shahid, K.A.; Rehman, S.; Qureshi, A.H.; Khan, I.H.

1999-01-01

Microstructural and oxidation characteristics of aluminized coated Inconel 625 have been examined using scanning electron microscopy (SEM) and fine-probe spot and linescan EDS microanalysis techniques. The formation of slowly growing adherent metallic coatings is essential for protection against the severe environments. Aluminising of the superalloy samples was carried out by pack cementation process at 900 deg. C. in an argon atmosphere. The samples were subsequently oxidized in air at various temperatures to examine performance of the pack aluminized coated alloy. The microstructural changes that occurred in the aluminized layer at various exposure temperature and time were examined to study the oxidation behavior and formation of different phases in the aluminized coating deposited on Inconel 625. (author)

Method of producing spherical lithium aluminate particles

International Nuclear Information System (INIS)

Yang, L.; Medico, R.R.; Baugh, W.A.

1983-01-01

Spherical particles of lithium aluminate are formed by initially producing aluminium hydroxide spheroids, and immersing the spheroids in a lithium ion-containing solution to infuse lithium ions into the spheroids. The lithium-infused spheroids are rinsed to remove excess lithium ion from the surface, and the rinsed spheroids are soaked for a period of time in a liquid medium, dried and sintered to form lithium aluminate spherical particles. (author)

Actinide-Aluminate Speciation in Alkaline Radioactive Waste

International Nuclear Information System (INIS)

Clark, David L.; Fedosseev, Alexander M.

2001-01-01

Investigation of behavior of actinides in alkaline media containing AL(III) showed that no aluminate complexes of actinides in oxidation states (IIII-VIII) were formed in alkaline solutions. At alkaline precipitation IPH (10-14) of actinides in presence of AL(III) formation of aluminate compounds is not observed. However, in precipitates contained actinides (IIV)<(VI), and to a lesser degree actinides (III), some interference of components takes place that is reflected in change of solid phase properties in comparison with pure components or their mechanical mixture. The interference decreases with rise of precipitation PH and at PH 14 is exhibited very feebly. In the case of NP(VII) the individual compound with AL(III) is obtained, however it is not aluminate of neptunium(VII), but neptunate of aluminium(III) similar to neptunates of other metals obtained earlier

Duplex aluminized coatings

Science.gov (United States)

Gedwill, M. A.; Grisaffe, S. J. (Inventor)

1975-01-01

The surface of a metallic base system is initially coated with a metallic alloy layer that is ductile and oxidation resistant. An aluminide coating is then applied to the metallic alloy layer. The chemistry of the metallic alloy layer is such that the oxidation resistance of the subsequently aluminized outermost layer is not seriously degraded.

Possibilities of using aluminate cements in high-rise construction

Science.gov (United States)

Kaddo, Maria

2018-03-01

The article describes preferable ways of usage of alternative binders for high-rise construction based on aluminate cements. Possible areas of rational use of aluminate cements with the purpose of increasing the service life of materials and the adequacy of the durability of materials with the required durability of the building are analyzed. The results of the structure, shrinkage and physical and mechanical properties of concrete obtained from dry mixes on the base of aluminate cements for self-leveling floors are presented. To study the shrinkage mechanism of curing binders and to evaluate the role of evaporation of water in the development of shrinkage was undertaken experiment with simple unfilled systems: gypsum binder, portland cement and «corrosion resistant high alumina cement + gypsum». Principle possibility of binder with compensated shrinkage based on aluminate cement, gypsum and modern superplasticizers was defined, as well as cracking resistance and corrosion resistance provide durability of the composition.

Variability in properties of grouted Phosphate/Sulfate N-Reactor Waste

International Nuclear Information System (INIS)

Lokken, R.O.; Martin, P.F.C.; Bowen, W.M.; Harty, H.; Treat, R.L.

1987-02-01

A Transportable Grout Facility (TGF) is being constructed at the Hanford site in Washington State to convert various low-level liquid wastes to a grout waste form for onsite disposal. The TGF Project is managed by Rockwell Hanford Operations (Rockwell). Oak Ridge National Laboratory (ORNL) has provided a grout formulation for Phosphate/Sulfate N-Reactor Waste, the first waste stream scheduled for grouting beginning in late 1987. The formulation includes a blend of portland cement, fly ash, attapulgite clay, and an illitic clay. Grout will be produced by mixing the blend with Phosphate/Sulfate N-Reactor Waste. These wastes result from decontamination and ion-exchange regeneration activities at Hanford's N-Reactor. Pacific Northwest Laboratory (PNL) is conducting studies on grouted Phosphate/Sulfate N-Reactor Waste to verify that the grout can be successfully processed and, when hardened, that it will meet all performance and regulatory requirements. As part of these studies, PNL is assessing the variability that may be encountered when processing Phosphate/Sulfate N-Reactor Waste grout. Sources of variability that may affect grout properties include the composition and concentrations of the waste and dry solids, temperature, efficiency of dry solids blending, and dry blend storage time. 13 refs., 20 figs., 9 tabs

Properties of lithium aluminate for application as an OSL dosimeter

International Nuclear Information System (INIS)

Twardak, A.; Bilski, P.; Marczewska, B.; Lee, J.I.; Kim, J.L.; Gieszczyk, W.; Mrozik, A.; Sądel, M.; Wróbel, D.

2014-01-01

Several samples of undoped and carbon or copper doped lithium aluminate (LiAlO 2 ) were prepared in an attempt to achieve a material, which can be applicable in optically stimulated luminescence (OSL) dosimetry. All investigated samples are highly sensitive to ionizing radiation and show good reproducibility. The undoped and copper doped samples exhibit sensitivity several times higher than that of Al 2 O 3 :C, while sensitivity of the carbon doped samples is lower. The studied samples exhibit significant fading, but dynamics of signal loss is different for differently doped samples, what indicates a possibility of improving this characteristic by optimizing dopant composition. - Highlights: • OSL properties of lithium aluminate for personal dosimetry. • Doping influence on OSL fading of lithium aluminate. • Application of lithium aluminate in thermal neutron measurements

Investigation of tritium release and retention in lithium aluminate

International Nuclear Information System (INIS)

Kopasz, J.P.; Tistchenko, S.; Botter, F.

1991-01-01

Tritium release from lithium aluminate, although previously investigated by both in-reactor and ex-reactor experiments, remains poorly understood. Agreement between experiments is lacking, and the mechanisms responsible for tritium release from lithium aluminate are under debate. In an effort to improve our understanding of the mechanisms of tritium release from lithium ceramics, we have investigated tritium release from pure lithium aluminate and lithium aluminate doped with impurities. The results of these experiments on large grain size material indicate that after anneals at low temperature, a large fraction of the tritium present before the anneal remains in the sample. We have modeled this behavior based on first-order release from three types of sites. At the lowest temperature, the release is dominated by one site, while the tritium in the other sites is retained in the solid. Adding magnesium dopant to the ceramic appears to alter the distribution of tritium between the sites. This addition decreases the fraction of tritium released at 777 degree C, while increasing the fractions released at 538 and 950 degree C. 11 refs., 8 figs., 1 tab

Recovery of uranium from the Syrian phosphate by solid-liquid method using alkaline solutions

International Nuclear Information System (INIS)

Shlewit, H.; Alibrahim, M.

2007-01-01

Uranium concentrations were analyzed in the Syrian phosphate deposits. Mean concentrations were found between 50 and 110 ppm. As a consequence, an average phosphate dressing of 22 kg/ha phosphate would charge the soil with 5-20 g/ha uranium when added as a mineral fertilizer. Fine grinding phosphate produced at the Syrian mines was used for uranium recovery by carbonate leaching. The formation of the soluble uranyl tricarbonate anion UO 2 (CO 3 ) 3 4- permits use of alkali solutions of sodium carbonate and sodium bicarbonate salts for the nearly selective dissolution of uranium from phosphate. Separation of iron, aluminum, titanium, etc., from the uranium during leaching was carried out. Formation of some small amounts of molybdates, vanadates, phosphates, aluminates, and some complexes metal was investigated. This process could be used before the manufacture of TSP fertilizer, and the final products would contain smaller uranium quantities. (author)

Synthesis of magnesium aluminate spinel by periclase and alumina chlorination

International Nuclear Information System (INIS)

Orosco, Pablo; Barbosa, Lucía; Ruiz, María del Carmen

2014-01-01

Highlights: • Use of chlorination for the synthesis of magnesium aluminate spinel. • The reagents used were alumina, periclase and chlorine. • Isothermal and non-isothermal assays were performed in air and Cl 2 –N 2 flows. • The chlorination produced magnesium aluminate spinel at 700 °C. • Selectivity of the chlorination reaction to obtain spinel is very high. - Abstract: A pyrometallurgical route for the synthesis of magnesium aluminate spinel by thermal treatment of a mechanical mixture containing 29 wt% MgO (periclase) and 71 wt% Al 2 O 3 (alumina) in chlorine atmosphere was developed and the results were compared with those obtained by calcining the same mixture of oxides in air atmosphere. Isothermal and non-isothermal assays were performed in an experimental piece of equipment adapted to work in corrosive atmospheres. Both reagents and products were analyzed by differential thermal analysis (DTA), X-ray diffraction (XRD) and X-ray fluorescence (XRF). Thermal treatment in Cl 2 atmosphere of the MgO–Al 2 O 3 mixture produces magnesium aluminate spinel at 700 °C, while in air, magnesium spinel is generated at 930 °C. The synthesis reaction of magnesium aluminate spinel was complete at 800 °C

Thermal decomposition of calcium aluminium phosphate of Thies. [Vaporization of uranium and phosphorus pentoxide

Energy Technology Data Exchange (ETDEWEB)

Allaf, K; Rouanet, A

1984-01-01

This study is related to the work on beneficiation of raw phosphates by thermal processing (selective vaporization). More precisely it deals with the ability of a calcium-aluminium phosphate (ores from Thies) to vaporize selectively as phosphorus pentoxide and uranium contents. Experiments are performed on liquid samples at Tsub(f)aluminous compounds remain as stable phases in the residuum.

Tritium extraction from neutron-irradiated lithium aluminate

International Nuclear Information System (INIS)

Garcia H, F.

1995-01-01

Lithium aluminate is being strongly considered as a breeder material because of its thermophysical, chemical and mechanical stability at high temperatures and its favorable irradiation behavior. Furthermore, it is compatible with other blanket and structural materials. In this work, the effects of calcination temperature during preparation, extraction temperature and sweep gas composition were observed. Lithium aluminate prepared by four different methods, was neutron irradiated for 30 minutes at a flux of 10 12 -10 13 n/cm 2 s in the TRIGA Mark III reactor at Salazar, Mexico; and the tritium extraction rate was measured. Calcination temperature do not affect the tritium extraction rate. However, using high calcination temperature, gamma lithium aluminate was formed. The tritium extraction at 600 Centigrade degrees was lower than at 800 Centigrade degrees and the tritium amount extracted by distillation of the solid sample was higher. The sweep gas composition showed that tritium extraction was less with Ar plus 0.5 % H 2 that with Ar plus 0.1 % H 2 . This result was contrary to expected, where the tritium extraction rate could be higher when hydrogen is added to the sweep gas. Probably this effect could be attributed to the gas purity. (Author)

Ecologically safe process for sulfo-aluminizing of steel parts

Directory of Open Access Journals (Sweden)

Plyatsuk L. D.

2018-06-01

Full Text Available The present technical solution refers to the field of electrophysical and electrochemical processing of parts, in particular, to the electroerosion alloying (EEA of the surfaces of steel parts with aluminum (aluminizing and sulfur (sulfidizing, and it can be used to treat the surfaces of heat-treated steel parts in order to increase their hardness, wear resistance, to prevent frictional seizure and improve the resistance to atmospheric corrosion. When aluminizing steel parts with the use of the method of electroerosion alloying (EEA by aluminum electrode at discharge energy Wp = 0.52–6.8 J and productivity of 1.0–3.0 cm2 / min, before the EEA process by an aluminum electrode, to the surface of the part to be aluminized, there is applied a consistency substance containing sulfur and aluminum powder, and thereafter, not having waited for drying of the consistency substance, the process of aluminizing by the EEL method with an aluminum electrode is carried out, and the consistency substance should have the aluminum powder content of not more than 56 %. There have been carried out metallographic and durametric analyses of the features of the surface layers made of carbon steels after simultaneous aluminizing and sulfidizing them by the EEA method. It is shown that the structure of the layer consists of three portions, namely, a “white” layer, a diffusion zone and a base metal. Such qualitative surface layer parameters as thickness, “white” layer and transition zone microhardness values, and also roughness increase with increasing discharge energy. The “white” layer continuity for all the investigated discharge energies of Wp = 0.52, 2.60 and 6.80 J is 100 %.

Tm3+ activated lanthanum phosphate: a blue PDP phosphor

International Nuclear Information System (INIS)

Rao, R.P.

2005-01-01

Plasma display panels (PDPs) are gaining attention due to their high performance and scalability as a medium for large format TVs. The performance and life of a PDP strongly depends upon the nature of phosphors. Currently, Eu 2+ activated barium magnesium aluminate (BAM) is being used as a blue component. Because of its low life, efforts are being made to explore new blue emitting phosphors. One of the alternatives to BAM is Tm 3+ activated lanthanum phosphate (LPTM) phosphor. LPTM phosphor samples are prepared by a solid-state as well as sol-gel process in presence of flux. The phosphor of the present investigation, having uniform and spherical shape particles in the range of 0.1-2 μm, is appropriate for thin phosphor screens required for PDP applications. It exhibits a narrow band emission in the blue region, peaking at 452 nm and also a number of narrow bands in the UV region when excited by 147 and 173 nm radiation from a xenon gas mixture. Various possible transitions responsible for UV and visible emission from Tm 3+ ion are presented. These phosphors also exhibit good color saturation and better stability when excited with VUV radiation. To achieve higher brightness, they are blended with other UV excited blue emitting phosphors such as BAM. Results related to morphology, excitation, after glow decay, emission and degradation of these phosphors in the powder form as well as in plasma display panels are presented and discussed

Effects of Na4EDTA and EDTA on seeded precipitation of sodium aluminate solution

Institute of Scientific and Technical Information of China (English)

吕保林; 陈启元; 尹周澜; 胡慧萍

2010-01-01

Na4EDTA and EDTA were adopted as new additives to intensify the seeded precipitation process of sodium aluminate solution. The effects of the two additives at certain concentrations on the seeded precipitation rate of sodium aluminate solution, particle size distribution (PSD) and morphology of precipitated gibbsite were investigated using titration method, particle size analyzer and scanning electron microscope (SEM), respectively. The results show that the two additives can accelerate the seeded precipitation rate of sodium aluminate solution. At relatively high concentration, the facilitative effect of EDTA on sodium aluminate solution is more obvious than that of Na4EDTA. EDTA makes gibbsite particles thinner than Na4EDTA. The Na+ and H+ result in the different effects on the seeded precipitation rate of sodium aluminate solution in spite of the same EDTA anion in the two additives.

Lithium aluminate spheroids prepared by emulsion procedure

International Nuclear Information System (INIS)

Mateos, A.G.; DiBello, P.M.; Zaleski, A.B.

1991-01-01

Lithium aluminate powders were prepared by emulsion evaporation method. The procedure involved preparation of water-in-oil emulsion, with the aqueous phase being a solution of Li and Al nitrates. The mixed salts precursor crystallized to gamma-LiAlO 2 at 700C. Single phase LiAlO 2 occurred as μm spherical particles with average crystallite size of 81 angstrom and surface area of 14 M 2 /g. After prolonged heating at 900C, the aluminate powder crystallite size grew by 5 times with a reduction in particle porosity. The emulsion technique promotes close control of particle size and shape of product and the technique facilitates chemical reaction of constituents and sinterability of resulting product

Corrosion of Spiral Rib Aluminized Pipe

Science.gov (United States)

2012-08-01

Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

Oxidation behavior and compositional analysis of aluminized superalloy

International Nuclear Information System (INIS)

Khalid, F.A.; Nawaz, F.

2003-01-01

The high temperature oxidation behavior of superalloy specimens used for the manufacture of turbine blades has been examined using scanning electron microscopy (SEM) and fine-probe spot and line scan EDS microanalysis techniques. The performance of aluminized coating applied to the specimens has also been examined. It was observed that complex oxides are formed in both coated and uncoated specimens. However the coated specimens revealed a greater stability of gamma phase and integrity of aluminized coating as compared with uncoated specimens. The microchemical and microstructural changes that occurred during oxidation have been analyzed to examine characteristics of oxide layers. (author)

Corrosion control of galvanized steel using a phosphate/calcium ion inhibitor mixture

International Nuclear Information System (INIS)

Zin, I.M.; Lyon, S.B.; Pokhmurskii, V.I.

2003-01-01

The corrosion inhibition of galvanized steel was studied in artificial acid rain solution using extracts of pigments normally used in organic coatings for corrosion control. It was established that a combination of zinc phosphate/molybdate and calcium ion exchange silica has a significant synergetic anticorrosion effect in the acid rain solution compared to the pigments used alone. Further, the charge transfer resistance of galvanized steel in acid rain solution saturated by the above pigment blend approaches that of strontium chromate in artificial acid rain solution. Use of the pigment blend was found to lead to development of a protective film, which is thought to be a complex mixture of calcium phosphates and zinc phosphate

Origins of saccharide-dependent hydration at aluminate, silicate, and aluminosilicate surfaces.

Science.gov (United States)

Smith, Benjamin J; Rawal, Aditya; Funkhouser, Gary P; Roberts, Lawrence R; Gupta, Vijay; Israelachvili, Jacob N; Chmelka, Bradley F

2011-05-31

Sugar molecules adsorbed at hydrated inorganic oxide surfaces occur ubiquitously in nature and in technologically important materials and processes, including marine biomineralization, cement hydration, corrosion inhibition, bioadhesion, and bone resorption. Among these examples, surprisingly diverse hydration behaviors are observed for oxides in the presence of saccharides with closely related compositions and structures. Glucose, sucrose, and maltodextrin, for example, exhibit significant differences in their adsorption selectivities and alkaline reaction properties on hydrating aluminate, silicate, and aluminosilicate surfaces that are shown to be due to the molecular architectures of the saccharides. Solid-state (1)H, (13)C, (29)Si, and (27)Al nuclear magnetic resonance (NMR) spectroscopy measurements, including at very high magnetic fields (19 T), distinguish and quantify the different molecular species, their chemical transformations, and their site-specific adsorption on different aluminate and silicate moieties. Two-dimensional NMR results establish nonselective adsorption of glucose degradation products containing carboxylic acids on both hydrated silicates and aluminates. In contrast, sucrose adsorbs intact at hydrated silicate sites and selectively at anhydrous, but not hydrated, aluminate moieties. Quantitative surface force measurements establish that sucrose adsorbs strongly as multilayers on hydrated aluminosilicate surfaces. The molecular structures and physicochemical properties of the saccharides and their degradation species correlate well with their adsorption behaviors. The results explain the dramatically different effects that small amounts of different types of sugars have on the rates at which aluminate, silicate, and aluminosilicate species hydrate, with important implications for diverse materials and applications.

Solubilities of sodium nitrate, sodium nitrite, and sodium aluminate in simulated nuclear waste

International Nuclear Information System (INIS)

Reynolds, D.A.; Herting, D.L.

1984-09-01

Solubilities were determined for sodium nitrate, sodium nitrite, and sodium aluminate in synthetic nuclear waste liquor. Solubilities were determined as a function of temperature and solution composition (concentrations of sodium hydroxide, sodium nitrate, sodium nitrite, and sodium aluminate). Temperature had the greatest effect on the solubilities of sodium nitrate and sodium nitrite and a somewhat lesser effect on sodium aluminate solubility. Hydroxide had a great effect on the solubilities of all three salts. Other solution components had minor effects. 2 references, 8 figures, 11 tables

Rheological Characterization of Isabgol Husk, Gum Katira Hydrocolloids, and Their Blends

Directory of Open Access Journals (Sweden)

Vipin Kumar Sharma

2014-01-01

Full Text Available The rheological parameters of Isabgol husk, gum katira, and their blends were determined in different media such as distilled water, 0.1 N HCl, and phosphate buffer (pH 7.4. The blend properties of Isabgol husk and gum katira were measured for four different percentage compositions in order to understand their compatibility in dispersion form such as 00 : 100, 25 : 50, 50 : 50, 75 : 25, and 100 : 00 in the gel strength of 1 mass%. The miscibility of blends was determined by calculating Isabgol husk-gum katira interaction parameters by Krigbaum and Wall equation. Other rheological properties were analyzed by Bingham, Power, Casson, Casson chocolate, and IPC paste analysis. The study revealed that the power flow index “p” was less than “1” in all concentrations of Isabgol husk, gum katira, and their blends dispersions indicating the shear-thinning (pseudoplastic behavior. All blends followed pseudoplastic behavior at thermal conditions as 298.15, 313.15, and 333.15°K and in dispersion media such as distilled water, 0.1 N HCl, and phosphate buffer (pH 7.4. Moreover, the study indicated the applicability of these blends in the development of drug delivery systems and in industries, for example, ice-cream, paste, nutraceutical, and so forth.

The formation reaction of calcium hexa-aluminate

International Nuclear Information System (INIS)

Tuganova, S.Kh.; Sirajiddinov, N.A.

1990-01-01

The formation reaction of CaAl 12 O 19 at interaction of calcium oxide and aluminium in solid form has been studied. Some physical-chemical characteristics of calcium hexa-aluminate are given. (author)

Evaluation of salt, polyphosphates and their blends at different levels on physicochemical properties of buffalo meat and patties.

Science.gov (United States)

Anjaneyulu, A S; Sharma, N; Kondaiah, N

1989-01-01

The effects of sodium pyrophosphate (SPP), sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), sodium acid pyrophosphate (SAPP) and their blends at different levels (0·3, 0·5 and 0·7%), along with 2% sodium chloride on certain quality parameters of buffalo meat and patties were evaluated. The SPP, STPP and phosphate blends significantly increased pH, water-holding capacity (WHC), emulsifying capacity (EC), extractability of salt soluble proteins (SSP), colour of ground meat, decreased cooking loss (CL), improved emulsion stability (ES) and enhanced yield, texture and moisture retention of cooked patties. Compared to these phosphates, SAPP and SHMP had significantly poorer effects on improving the quality of meat and patties. The order of effectiveness of phosphates was SPP > STPP > SHMP. In general, pH, WHC, SSP, ES, yield and moisture content of patties increased progressively with increasing level of phosphate while CL decreased. Among blends containing two polyphosphates, those of 90% SPP + 10% SHMP and 75% SPP + 25% STPP were relatively more effective. A phosphate blend consisting of 65% SPP, 17·5% STPP and 17·5% SAPP was equally effective as that of SPP in improving the functionality of hot and chilled meat and had the advantage of reducing the amount of sodium by 3%. Copyright © 1989. Published by Elsevier Ltd.

Characterizing AISI 1045 steel surface duplex-treated by alternating current field enhanced pack aluminizing and nitriding

Science.gov (United States)

Xie, Fei; Zhang, Ge; Pan, Jianwei

2018-02-01

Thin cases and long treating time are shortcomings of conventional duplex treatment of aluminizing followed by nitriding (DTAN). Alternating current field (ACF) enhanced DTAN was carried out on AISI 1045 steel by applying an ACF to treated samples and treating agents with a pair of electrodes for overcoming those shortcomings. By investigating cases' structures, phases, composition and hardness distributions of differently treated samples, preliminary studies were made on characterizations of the ACF enhanced duplex treatment to AISI 1045 steel. The results show that, with the help of the ACF, the surface Al-rich phase Al5Fe2 formed in conventional pack aluminizing can be easily avoided and the aluminizing process is dramatically promoted. The aluminizing case can be nitrided either with conventional pack nitriding or ACF enhanced pack nitriding. By applying ACF to pack nitriding, the diffusion of nitrogen into the aluminizing case is promoted. AlN, Fe2∼3N and solid solution of N in iron are efficiently formed as a result of reactions of N with the aluminizing case. A duplex treated case with an effective thickness of more than 170 μm can be obtained by the alternating current field enhanced 4 h pack aluminizing plus 4 h pack nitriding.

Synthesis of calcium aluminates on the big solar furnace

International Nuclear Information System (INIS)

Abdurakhmanov, A. A.; Paizullakhanov, M. S.; Akhadov, Zh.

2012-01-01

The processes of synthesizing calcium aluminate in the flow of concentrated solar radiation on Large Solar Furnace are studied. It is shown that the synthesis of calcium aluminate takes place through a process of melting of a mixture of aluminum oxides and calcium (Al 2 O 3 + CaO). At values of power of the concentrated flow of 200 W/cm 2 , thermodynamic conditions for melting of the materials studied were implemented. Full fusion penetration is achieved at a power flow of 400 W/cm 2 . The resulting material exhibits high mechanical properties (the modulus of rupture upon bending is 40 MPa). (author)

Inhibited Aluminization of an ODS FeCr Alloy

International Nuclear Information System (INIS)

Vande Put Ep Rouaix, Aurelie; Pint, Bruce A.

2012-01-01

Aluminide coatings are of interest for fusion energy applications both for compatibility with liquid Pb-Li and to form an alumina layer that acts as a tritium permeation barrier. Oxide dispersion strengthened (ODS) ferritic steels are a structural material candidate for commercial reactor concepts expected to operate above 600 C. Aluminizing was conducted in a laboratory scale chemical vapor deposition reactor using accepted conditions for coating Fe- and Ni-base alloys. However, the measured mass gains on the current batch of ODS Fe-14Cr were extremely low compared to other conventional and ODS alloys. After aluminizing at two different Al activities at 900 C and at 1100 C, characterization showed that the ODS Fe-14Cr specimens formed a dense, primarily AlN layer that prevented Al uptake. This alloy batch contained a higher (> 5000 ppma) N content than the other alloys coated and this is the most likely reason for the inhibited aluminization. Other factors such as the high O content, small (∼ 140 nm) grain size and Y-Ti oxide nano-clusters in ODS Fe-14Cr also could have contributed to the observed behavior. Examples of typical aluminide coatings formed on conventional and ODS Fe- and Ni-base alloys are shown for comparison.

Morphological and microstructural studies on aluminizing coating of carbon steel

Energy Technology Data Exchange (ETDEWEB)

Samsu, Zaifol; Othman, Norinsan Kamil; Daud, Abd Razak; Hussein, Hishammuddin [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

2013-11-27

Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity. The morphology and microstructure of an inter-metallic layer form on the surface of low carbon steel by hot dip aluminization treatment had been studied in detail. This effect has been investigated using optical and scanning electron microscopy, and X-ray diffraction. The result shows that the reaction between the steel and the molten aluminium leads to the formation of Fe–Al inter-metallic compounds on the steel surface. X-ray diffraction and electron microscopic studies showed that a two layer coating was formed consisting of an external Al layer and a (Fe{sub 2}Al{sub 5}) inter metallic on top of the substrate after hot dip aluminizing process. The inter-metallic layer is ‘thick’ and exhibits a finger-like growth into the steel. Microhardness testing shown that the intermetallic layer has high hardness followed by steel substrate and the lowest hardness was Al layer.

Microstructure and High-temperature Wear Behavior of Hot-dipped Aluminized Coating on Different Substrate Materials

Directory of Open Access Journals (Sweden)

ZHOU De-qin

2018-02-01

Full Text Available The aluminized 45 and H13 steel were prepared via hot-dipped aluminizing and subsequently high-temperature diffusion treatment. The phase, morphology and composition of aluminized coating were characterized by XRD,SEM and EDS methods. Comparative study was performed on unlubricated sliding wear behavior of plating under different substrates on a pin-on-disc wear tester, and the wear mechanism was explored. The results show that the coating is composed of ductile phases FeAl and Fe3Al. Kikendall porosity parallel to the surface exists around the interface of the two phases; because of the carbide particles agglomeration, the bond between the coating and H13 steel is apparently inferior to that in the case of 45 steel; the aluminized 45 steel possesses an excellent wear resistance under 50-200N at 400℃, whereas mild-to-severe wear transition occurs when the temperature increases to 600℃. The wear rate of the aluminized H13 steel reaches the lowest at 400℃, then slightly increases at 600℃. The wear mechanisms of Fe-Al coating are mainly predominated by oxidative mild wear, whereas the extrusion wear prevails in the process for aluminized 45 steel at 600℃.

Corrosion of Spiral Rib Aluminized Pipe : [Summary

Science.gov (United States)

2012-01-01

Large diameter, corrugated steel pipes are a common sight in the culverts that run alongside many Florida roads. Spiral-ribbed aluminized pipe (SRAP) has been widely specified by the Florida Department of Transportation (FDOT) for runoff drainage. Th...

Determination of hydroxide in the presence of aluminate using a modified potentiometric titration

International Nuclear Information System (INIS)

Hanson, T.J.

1975-11-01

A procedure for the determination of hydroxide concentration in the presence of aluminate and other interfering ions was developed using the method of standard additions (or more specifically in this case, standard subtractions). The procedure called for titration with a strong acid which was added in equal increments at regular time intervals. The potential was recorded after each addition of acid. The data was plotted on Gran's Plot Paper, which is based on work done originally by Gran, or it was entered into a computer to determine the equivalence volume of the titrant. When used on many different samples in different matrices, the method gave results that were approximately 100 +- 1 percent of the calculated value. This was shown to be true even in systems containing aluminate [Al(OH) 4 - ], phosphate (PO 4 3- ), sulfate (SO 4 2- ), nitrate (NO 3 - ), nitrite (NO 2 - ), carbonate (CO 3 2- ), and other ions. The effect of these ions was shown to be negligible if the initial OH - concentration was at least 10 -3 M and barium chloride (BaCl 2 ) was added to complex the PO 4 3- and CO 3 2- ions. These ions were checked at levels of up to 3 M for Al(OH) 4 - and NO 3 - , 2 M for NO 2 - , and 1 M for SO 4 2- , PO 4 3- , and CO 3 2- . The method is applicable to radioactive as well as nonradioactive samples and any heat involved with a radioactive sample is insufficient to cause an error in the determination. On the basis of the work performed it was shown that the method was general enough to be run on a routine basis

Thermoluminescent response of calcium di aluminate intrinsic and doped with Cr3+

International Nuclear Information System (INIS)

Ceron R, P. V.; Vallejo H, M. A.; Sosa A, M. A.; Montes R, E.; Diaz G, J. A. I.; Diaz T, L. A.

2017-10-01

In numerous studies the thermoluminescent response (Tl) of aluminum oxide has been presented in which various dopants have been incorporated to increase the number of defects and thus modify their dosimetric properties. In related materials such as aluminates have been doped with trivalent ions and their optical characteristics have been determined. Due to this background, the motivation to study the aluminates as possible thermoluminescent dosimeters arises. In this work the synthesis of intrinsic calcium aluminate powders and doped with Cr 3+ is presented by the combustion method, to elaborate pellets and evaluate their Tl response with different radiation sources. The material obtained was characterized by XRD, X-ray fluorescence and UV-Vis; it was found to belong to the monoclinic phase of calcium di aluminate (CaAl 4 O 7 ) with a crystal size of 55 nm, the presence of Cr 3+ in the crystal lattice was also observed. The samples showed a good response Tl for UV radiation, X-rays from a 70 kV source and for Co-60 gammas. The results found show that CaAl 4 O 7 is a good candidate to study its dosimetric properties. (Author)

A contribution to the regeneration of ettringite as a donor of aluminous ions

Directory of Open Access Journals (Sweden)

Silvie Heviánková

2005-11-01

Full Text Available At our institute was developed a technological procedure of mine water desulphation. The metod consists of chemical precipitation by sodium aluminate and calcium hydroxide. By the application of this metod, very interesting results were obtained. The amount of SO42- anions decreased to almost zero-value, using optimal doses of the chemical reagents. The incurred sludge was subjected to the partial dissolving by sulphuric acid with the aim wiev to obtain aluminous ionts in the solution. From this solution, the aluminous ions were separated selectively by two methods. In the first case is added calcium chloride for the precipitation of sulphates. In the second case is added sodium hydroxide for the controled neutralization.

Phase transformations in lithium aluminates irradiated with neutrons

International Nuclear Information System (INIS)

Carrera, L.M.; Delfin L, A.; Urena N, F.; Basurto, R.; Bosch, P.

2003-01-01

The lithium aluminate like candidate to be used in the coverings producers of tritium in the fusion nuclear reactors, presents high resistance to the corrosion to the one to be stuck to structural materials as special steels. However, the crystallographic changes that take place in the cover that is continually subjected to irradiation with neutrons, can alter its resistance to the corrosion. In this work the changes of crystalline structure are shown that they present two types of nano structures of lithium aluminates, subjected to an average total dose 7.81 x 10 8 Gy in the fixed irradiation system of capsules of the one TRIGA Mark lll nuclear reactor of the Nuclear Center of Mexico. The studied nano structures presented only phase transformations without formation of amorphous material. (Author)

A drift chamber constructed of aluminized mylar tubes

Science.gov (United States)

Baringer, P.; Jung, C.; Ogren, H. O.; Rust, D. R.

1987-03-01

A thin reliable drift chamber has been constructed to be used near the interaction point of the PEP storage ring in the HRS detector. It is composed of individual drift tubes with aluminized mylar walls.

Optimization of a Strontium Aluminate

Energy Technology Data Exchange (ETDEWEB)

Bone, Alexandria N. [Maryville College, TN (United States)

2017-08-01

Strontium aluminate with Eu²⁺ and Dy³⁺ has been at the forefront of emerging applications for storage phosphors since its discovery in 1996. In this study, the emission intensity and luminescence lifetime of SrAl₂O₄: Eu²⁺, Dy³⁺ were enhanced by partial substitution of Ca²⁺ into Sr²⁺ sites in the matrix.

Re-examining the prospects of aluminous cements based on alkali-earth and rare-earth oxides

International Nuclear Information System (INIS)

Chatterjee, A.K.

2009-01-01

In the family of aluminous cements the potential of strontium aluminate, the strontium-barium aluminate and the barium aluminate cements have been sporadically and incoherently studied over several decades in various parts of the world and more particularly in the East European countries without much wide-spread commercial success. Attempts had also been made to extend the exploratory studies to the (Ca, Sr, Ba)O-Al 2 O 3 -ZrO 2 -HfO 2 system to synthesize super-refractory binders. In fact, the above compositions, prima facie, seem to have the potential of arriving at cementitious formulations that, apart from being super-refractory, may as well be highly resistant to seawater, X-rays and gamma radiation. Looking at these potentials, quite a few experimental studies have been carried out under the guidance and supervision of the present author. The present paper is an endeavour to collate the data on some of these systems both from the published literature as well as from the author's findings. The prime motive has been to review and re-assess the prospects of manufacturing a range of new aluminous binders with superior properties.

Comparative tribological studies of duplex surface treated AISI 1045 steels fabricated by combinations of plasma nitriding and aluminizing

International Nuclear Information System (INIS)

Haftlang, Farahnaz; Habibolahzadeh, Ali; Sohi, Mahmoud Heydarzadeh

2014-01-01

Highlights: • AlN coating was applied on AISI 1045 steel via plasma nitriding and aluminizing. • Aluminizing of pre-nitrided specimen provides the highest surface hardness. • The lowest wear rate was obtained via aluminizing of pre-nitrided specimen. • Wear mechanism of the modified layer consists of oxidative and spallung wear. - Abstract: Duplex surface treatments via aluminizing and plasma nitriding were carried out on AISI 1045 steel. A number of work pieces were aluminized and subsequently plasma nitrided (Al–PN) and other work pieces were plasma nitrided and then aluminized (PN–Al). Aluminizing was carried out via pack process at 1123 K for 5 h and plasma nitriding was performed at 823 K for 5 h. The fabricated steels were characterized using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and microhardness testing. Tribological behaviors of the duplex treated AISI 1045 steels were examined against tungsten carbide pin using a pin-on-disc apparatus at room temperature. The PN–Al specimen showed higher surface hardness, lower wear rate and coefficient of friction than the Al–PN one. It was noticed from the worn surfaces that tribo-oxidation plays an important role in wear behavior of both specimens

A drift chamber constructed of aluminized mylar tubes

International Nuclear Information System (INIS)

Baringer, P.; Jung, C.; Ogren, H.O.; Rust, D.R.

1987-01-01

A thin reliable drift chamber has been constructed to be used near the interaction point of the PEP storage ring in the HRS detector. It is composed of individual drift tubes with aluminized mylar walls. (orig.)

Lithium aluminates and tritium production

International Nuclear Information System (INIS)

Carrera G, L.M.; Palacios G, O.; Bosch G, P.

1997-01-01

In this work it is studied the crystalline structure of lithium aluminates prepared by three different methods, namely: solid state reaction, humid reaction and sol-gel reaction. The analysis methods are the X-ray diffractometry and the scanning and transmission electron microscopy. This study is realized as in original materials as in irradiated materials at the TRIGA Mark reactor, to correlate the synthesis method with response of these materials to the mixed irradiation of nuclear reactor. (Author)

Effect of aluminizing on hardenability of steel (S45C)

Science.gov (United States)

Prayitno, D.; Sugiarto, R.

2018-01-01

The objective of research is to know the effect of aluminizing on hardenability of steel (S45C). The research methodologies were as follows. The Steels (S45C) were machined into the Jominy test samples. Next the samples were preheating at 700 ° C for 30 minutes and then the samples were dipped into the molten of aluminium for 3 minutes as a hot dip aluminizng method. The aluminium molten was 700 ° C. Then the samples were cooled into room temperatures. Finally the samples were into the jominy tested. The results show that the aluminizing (include the preheating process) increases the hardenability of steel (S45C).

THE ROLE OF METAL ION ON PHYSIOCHEMICAL PROPERTIES OF METAL ALUMINATES PREPARED BY IMPREGNATION METHOD

Directory of Open Access Journals (Sweden)

S. Komeili

2017-03-01

Full Text Available A series of MAl2O4 (M=Ni, Zn, and Cu aluminates were prepared by using impregnation method; the metal content of the products was ranged between 5wt% to 25wt%. The samples were characterized by x-ray diffraction (XRD, Brunauer Emmett Teller (BET surface area, NH3 temperature-programmed desorption (NH3-TPD, and inductively coupled argon plasma (ICP. The specific surface areas of zinc, nickel and copper aluminates were in the ranges of 47-77m2/g, 63-87m2/g and 1.6-3m2/g, respectively. The surface acidity decreased in the order of CuAl2O4<< NiAl2O4< ZnAl2O4<< Al2O3. By increasing the amount of metals in the samples, the number of acidic sites decreased, but their strength did not significantly change. Ni-aluminates have fewer acidic sites than Zn-aluminates, particularly in strong acid sites

High toughness alumina/aluminate: The role of hetero-interfaces

International Nuclear Information System (INIS)

Brito, M.E.; Yasuoka, M.; Kanzaki, S.

1996-01-01

Silica doped alumina/aluminate materials present a combination of high strength and high toughness not achieved before in other alumina systems, except for transformation toughened alumina. The authors have associated the increase in toughness to crack bridging by anisotropically grown alumina grains with concurrent interfacial debonding of these grains. A HREM study of grain boundaries and hetero-interface structures in this material shows the absence of amorphous phases at grain boundaries. Local Auger electron analysis of fractured surfaces revealed the coexistence of Si and La at the grain facets exposed by the noticeable intergranular fracture mode of this material. It is concluded that a certain and important degree of boundaries weakness is related to both presence of Si at the interfaces and existence of alumina/aluminate hetero-interfaces

Dipeptide-based polyphosphazene and polyester blends for bone tissue engineering.

Science.gov (United States)

Deng, Meng; Nair, Lakshmi S; Nukavarapu, Syam P; Jiang, Tao; Kanner, William A; Li, Xudong; Kumbar, Sangamesh G; Weikel, Arlin L; Krogman, Nicholas R; Allcock, Harry R; Laurencin, Cato T

2010-06-01

Polyphosphazene-polyester blends are attractive materials for bone tissue engineering applications due to their controllable degradation pattern with non-toxic and neutral pH degradation products. In our ongoing quest for an ideal completely miscible polyphosphazene-polyester blend system, we report synthesis and characterization of a mixed-substituent biodegradable polyphosphazene poly[(glycine ethyl glycinato)(1)(phenyl phenoxy)(1)phosphazene] (PNGEG/PhPh) and its blends with a polyester. Two dipeptide-based blends namely 25:75 (Matrix1) and 50:50 (Matrix2) were produced at two different weight ratios of PNGEG/PhPh to poly(lactic acid-glycolic acid) (PLAGA). Blend miscibility was confirmed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and scanning electron microscopy. Both blends resulted in higher tensile modulus and strength than the polyester. The blends showed a degradation rate in the order of Matrix2PLAGA in phosphate buffered saline at 37 degrees C over 12 weeks. Significantly higher pH values of degradation media were observed for blends compared to PLAGA confirming the neutralization of PLAGA acidic degradation by polyphosphazene hydrolysis products. The blend components PLAGA and polyphosphazene exhibited a similar degradation pattern as characterized by the molecular weight loss. Furthermore, blends demonstrated significantly higher osteoblast growth rates compared to PLAGA while maintaining osteoblast phenotype over a 21-day culture. Both blends demonstrated improved biocompatibility in a rat subcutaneous implantation model compared to PLAGA over 12 weeks. (c) 2010 Elsevier Ltd. All rights reserved.

Influence of chemical bonding of chlorides with aluminates in cement hidratation process on corrosion steel bars in concrete

Directory of Open Access Journals (Sweden)

Bikić Farzet H.

2010-01-01

Full Text Available The presence of chlorides in concrete is a permanent subject of research because they cause corrosion of steel bars. Chlorides added to the concrete during preparation, as accelerators of the bonding of cement minerals process, enter into reaction with aluminates, creating a phase known as chloroaluminate hydrates. In everyday conditions the product of chemical bonding between chlorides and aluminates is usually monochloridealuminate C3A·CaCl2·Hx, better known as Friedel's salt. In this paper, the influence of chemical bonding of chlorides with aluminates during the process of cement hydration on corrosion of steel bars in concrete was investigated. The process of chlorides bonding with aluminates yielding monochloride aluminate is monitored by XRD analyses. It was found that the amount of chlorides bonding with aluminates increases with an increase of temperature, and as a result, reduces the amount of 'free' chlorides in concrete. Potentiodynamic measurements have shown that increase in temperature of the heat treatment of working electrodes by chlorides leads to a reduction of steel bars corrosion as a result of either the increase of the monochloride-aluminate content or the decrease of free chlorides amount. Chlorides bound in chloroaluminate hydrates do not cause activation of steel bars corrosion in concrete. It was also proven that the increase of free chlorides concentration in the concrete leads to intensification of steel bars corrosion. This additionally approves that free chlorides are only the activators of process of steel bars corrosion in the concrete.

Study of the chemical species of fluorine 18 produced by neutron irradiation of lithium aluminate

International Nuclear Information System (INIS)

Jimenez-Becerril, J.

1990-01-01

In the present work, the chemical form of fluorine-18 obtained by means of the neutron irradiated lithium aluminate was studied, in order to know its chemical behavior and to observe if it volatilizes and adheres to the walls of a tritium distillation system; for this matter paper chromatography and high voltage electrophoresis techniques were used. Lithium aluminate was synthetized, being characterized as LiAlO 2 which was irradiated with neutrons in order to produce fluorine-18. Lithium aluminate is a non-soluble solid, therefore fluorine produced may not be extracted, unless it is dissolved or extracted through the solid. So as not affect in a drastic way the chemical form, it was submitted to extraction processes, agitating the irradiated samples with different acids and basic solutions in order to analyze fluorine-18. The best extraction agent was found to be HCl, where two forms of fluorine-18 were found, one at the point of application, probably as a complex hexafluoride-aluminate and the other as a characteristic Rf of the fluorine ion. In the tritium distillation with helium as a carrier of a sample irradiated and heated up to 220-250 o C, no volatile types of fluorine-18 were found, thus it can be considered that in commercial production of tritium by means of neutron irradiation of lithium aluminate, fluorine-18 is not a damaging pollutant of the equipment pipe system. (Author)

The Uses of Copper and Zinc Aluminates to Capture and Convert Carbon dioxide to Syn-gas at Higher Temperature

Directory of Open Access Journals (Sweden)

R.Y. Raskar

2014-03-01

Full Text Available The uses of copper and zinc aluminates to capture and convert the CO2 to syn-gas were studied at higher temperatures. The samples of copper and zinc aluminates were prepared by solid-solid fusion method by calcining in air at 900 oC for 3 h. Those samples were characterized by acidity/alkalinity, surface area, XRD pattern, IR, SEM images and screening to capture CO2 at the different temperatures. The phases Cu2O, CuO, ZnO, CuAl2O4 and ZnAl2O4 were found to be in the samples of zinc and copper aluminates. Acidity and surface area of the samples of copper and zinc aluminates were found to be in the ranges from 0.063 to 9.37 mmol g-1 and 3.04 to 11.8 m2 g-1, respectively. The captured CO2 by the samples of copper and zinc aluminates was found to be 19.92 to 31.52 wt% for the temperature range 40 to 850 oC. The captured CO2 at 550 oC by variable Zn/Al and Cu/Al mol ratio from 0.5 to 6 of the samples of copper and zinc aluminates was found to be 12.81 to 18.04 wt%. The reduction of carbon dioxide by zinc and copper aluminates was observed. The conversion of CO2 by methane over variable mol ratio of Cu/Al and Zn/Al in copper and zinc aluminates, respectively, at 500 oC showed the production of syn-gas by using the gas hourly space velocities (GHSV 12000, 12000 and 6000 ml. h-1. g-1 of helium, CO2 and methane. The conversions of CO2 by methane over the samples of zinc and copper aluminates were studied at different mol ratios of CO2 to methane.  © 2014 BCREC UNDIP. All rights reservedReceived: 13rd May 2013; Revised: 8th November 2013; Accepted: 8th November 2013[How to Cite: Raskar, R.Y., Gaikwad, A.G. (2014. The Uses of Copper and Zinc Aluminates to Cap-ture and Convert Carbon Dioxide to Syn-gas at Higher Temperature. Bulletin of Chemical Reaction Engineering & Catalysis, 9 (1: 1-15. (doi:10.9767/bcrec.9.1.4899.1-15[Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.1.4899.1-15

On structural, optical and dielectric properties of zinc aluminate ...

Indian Academy of Sciences (India)

reports on the dielectric properties of this material is very rarely found in literature. ... C placed on a heating man- ... and dielectric loss of the material using the equation ε = ε tan δ, ..... ble mechanism of a.c. conduction in zinc aluminate particles.

Irradiation and corrosion behaviour of cadmium aluminate, a burnable poison for light water reactors

International Nuclear Information System (INIS)

Hattenbach, K.; Ahlf, J.; Hilgendorff, W.; Zimmermann, H.U.

1979-01-01

In quest of a cadmium containing material for use as burnable poison cadmium aluminate seemed promising. Therefore irradiation and corrosion experiments on specimens of cadmium aluminate in a matrix of aluminia were performed. Irradiation at 575 K and fast fluences up to 10 25 m -2 showed the material to have good radiation resistance and low swelling rates. Cadmium pluminate was resistant to corrosion attack in demineralized water of 575K. (orig.) [de

Quantitative description of yttrium aluminate ceramic composition by means of Er+3 microluminescence spectrum

Science.gov (United States)

Videla, F. A.; Tejerina, M. R.; Moreira-Osorio, L.; Conconi, M. S.; Orzi, D. J. O.; Flores, T.; Ponce, L. V.; Bilmes, G. M.; Torchia, G. A.

2018-05-01

The composition of erbium-doped yttrium aluminate ceramics was analyzed by means of confocal luminescence spectroscopy, EDX, and X-ray diffraction. A well-defined linear correlation was found between a proposed estimator computed from the luminescence spectrum and the proportion of ceramic phases coexisting in different samples. This result shows the feasibility of using erbium luminescence spectroscopy to perform a quantitative determination of different phases of yttrium aluminates within a micrometric region in nanograined ceramics.

Function of magnesium aluminate hydrate and magnesium nitrate ...

Indian Academy of Sciences (India)

MgO was added both as spinel (MgAl2O4) forming precursor i.e. magnesium aluminate hydrate, and magnesium nitrate. Sintering investigations were conducted in the temperature range 1500–1600°C with 2 h soaking. Structural study of sintered pellets was carried out by extensive XRD analysis. Scanning electron mode ...

Thermochemical properties of gibbsite, bayerite, boehmite, diaspore, and the aluminate ion between 0 and 350/degree/C

International Nuclear Information System (INIS)

Apps, J.A.; Neil, J.M.; Jun, C.H.

1989-01-01

A requirement for modelling the chemical behavior of groundwater in a nuclear waste repository is accurate thermodynamic data pertaining to the participating minerals and aqueous species. In particular, it is important that the thermodynamic properties of the aluminate ion be accurately determined, because most rock forming minerals in the earth's crust are aluminosilicates, and most groundwaters are neutral to slightly alkaline, where the aluminate ion is the predominant aluminum species in solution. Without a precise knowledge of the thermodynamic properties of the aluminate ion aluminosilicate mineral solubilities cannot be determined. The thermochemical properties of the aluminate ion have been determined from the solubilities of the aluminum hydroxides and oxyhydroxides in alkaline solutions between 20 and 350/degree/C. An internally consistent set of thermodynamic properties have been determined for gibbsite, boehmite, diaspore and corundum. The thermodynamic properties of bayerite have been provisionally estimated and a preliminary value for ΔG/sub f, 298/ 0 of nordstrandite has been determined. 205 refs., 17 figs., 25 tabs

Electrical transport properties of calcium and barium aluminates

NARCIS (Netherlands)

Metselaar, R.; Hoefsloot, A.M.

1987-01-01

Electrical conductivity and ionic transport numbers have been measured of barium and calcium aluminates with composition CaO·nAl2O3 (n=7/12, 1, 2, 6) and 0.82 BaO·6Al2O3. At room temperatures these compounds are insulators, but at high temperatures mixed conductivity is observed. Ionic transport

Ion microprobe analyses of aluminous lunar glasses - A test of the 'rock type' hypothesis

Science.gov (United States)

Meyer, C., Jr.

1978-01-01

Previous soil survey investigations found that there are natural groupings of glass compositions in lunar soils and that the average major element composition of some of these groupings is the same at widely separated lunar landing sites. This led soil survey enthusiasts to promote the hypothesis that the average composition of glass groupings represents the composition of primary lunar 'rock types'. In this investigation the trace element composition of numerous aluminous glass particles was determined by the ion microprobe method as a test of the above mentioned 'rock type' hypothesis. It was found that within any grouping of aluminous lunar glasses by major element content, there is considerable scatter in the refractory trace element content. In addition, aluminous glasses grouped by major elements were found to have different average trace element contents at different sites (Apollo 15, 16 and Luna 20). This evidence argues that natural groupings in glass compositions are determined by regolith processes and may not represent the composition of primary lunar 'rock types'.

Study of damages by neutron irradiation in lithium aluminates

International Nuclear Information System (INIS)

Palacios G, O.

1999-01-01

Lithium aluminates proposed to the production of tritium in fusion nuclear reactors, due to the thermal stability that they present as well as the behavior of the aluminium to the irradiation. As a neutron flux with profile (≅ 14 Mev) of a fusion reactor is not available. A irradiation experiment was designed in order to know the micro and nano structure damages produced by fast and thermal neutrons in two irradiation positions of the fusion nuclear reactor Triga Mark III: CT (Thermal Column) and SIFCA (System of Irradiation Fixed of Capsules). In this work samples of lithium aluminate were characterized by XRD (X-Ray Diffraction), TEM (Transmission Electron Microscopy) and SEM (Scanning Electron Microscopy). Two samples were prepared by two methods: a) coalition method and b) peroxide method. This characterization comprised original and irradiated samples. The irradiated sample amounted to 4 in total: one for each preparation method and one for each irradiation position. The object of this analysis was to correlate with the received neutron dose the damages suffered by the samples with the neutron irradiation during long periods (440 H), in their micro and nano structure aspects; in order to understand the changes as a function of the irradiation zone (with thermal and fast neutron flux) and the preparation methods of the samples and having as an antecedent the irradiation in SIFCA position by short times (2h). The obtained results are referred to the stability of γ -aluminate phase, under given conditions of irradiation and defined nano structure arrangement. They also refer to the proposals of growth mechanism and nucleation of new phases. The error associated with the measurement of neutron dose is also discussed. (Author)

Recovering uranium and/or aluminium from refractory silico-aluminous material

International Nuclear Information System (INIS)

Livesey-Goldblatt, E.; Nagy, I.F.; Tunley, T.H.

1983-01-01

A process for recovering uranium and/or aluminium from a refractory silico-aluminous material comprises leaching the material in one or more stages, obtaining a pregnant solution which contains little or no acid and recovering the desired metal from the solution

Corn-soy-blend fortified with phosphorus to prevent refeeding hypophosphatemia in undernourished piglets

DEFF Research Database (Denmark)

Hother Nielsen, Anne-Louise; Lykke Jensen, Mikkel; Martinussen, Torben

2017-01-01

BACKGROUND: Phosphorus (P) levels in refeeding diets are very important as undernourished children are at risk of hypophosphatemia during refeeding. For this reason, conventional corn-soy-blends (CSB) have been reformulated by the World Food Programme to obtain a mono-calcium-phosphate fortified...

Investigation of barium-calcium aluminate process to manufacture and characterize impregnated thermionic cathode for power microwave devices

International Nuclear Information System (INIS)

Higashi, Cristiane

2006-01-01

In the present work it is described the barium calcium aluminate manufacture processes employed to produce impregnated cathodes to be used in a traveling-wave tube (TWT). The cathodes were developed using a tungsten body impregnated with barium and calcium aluminate with a 5:3:2 proportion (molar). Three different processes were investigated to obtain this material: solid-state reaction, precipitation and crystallization. Thermal analysis, thermogravimetry specifically, supported to determine an adequate preparation procedure (taking into account temperature, time and pyrolysis atmosphere). It was verified that the crystallization showed a better result when compared to those investigated (solid-state reaction and precipitation techniques - formation temperature is about 1000 deg C in hydrogen atmosphere), whereas it presented the lower formation temperature (800 deg C) in oxidizing atmosphere (O 2 ). It was used the practical work function distribution theory (PWFD) of Miram to characterize thermionic impregnated cathode. The PWFD curves were used to characterize the barium-calcium aluminate cathode. PWFD curves shown that the aluminate cathode work function is about 2,00 eV. (author)

Thermochemical properties of gibbsite, bayerite, boehmite, diaspore, and the aluminate ion between 0 and 350/degree/C

Energy Technology Data Exchange (ETDEWEB)

Apps, J.A.; Neil, J.M.; Jun, C.H.

1989-01-01

A requirement for modelling the chemical behavior of groundwater in a nuclear waste repository is accurate thermodynamic data pertaining to the participating minerals and aqueous species. In particular, it is important that the thermodynamic properties of the aluminate ion be accurately determined, because most rock forming minerals in the earth's crust are aluminosilicates, and most groundwaters are neutral to slightly alkaline, where the aluminate ion is the predominant aluminum species in solution. Without a precise knowledge of the thermodynamic properties of the aluminate ion aluminosilicate mineral solubilities cannot be determined. The thermochemical properties of the aluminate ion have been determined from the solubilities of the aluminum hydroxides and oxyhydroxides in alkaline solutions between 20 and 350/degree/C. An internally consistent set of thermodynamic properties have been determined for gibbsite, boehmite, diaspore and corundum. The thermodynamic properties of bayerite have been provisionally estimated and a preliminary value for ..delta..G/sub f, 298//sup 0/ of nordstrandite has been determined. 205 refs., 17 figs., 25 tabs.

A simple method for tuning the glass transition process in inorganic phosphate glasses

Science.gov (United States)

Fulchiron, René; Belyamani, Imane; Otaigbe, Joshua U.; Bounor-Legaré, Véronique

2015-02-01

The physical modification of glass transition temperature (Tg) and properties of materials via blending is a common practice in industry and academia and has a large economic advantage. In this context, simple production of hitherto unattainable new inorganic glass blends from already existing glass compositions via blending raises much hope with the potential to provide new glasses with new and improved properties, that cannot be achieved with classical glass synthesis, for a plethora of applications such as computers screens, glass-to-metal seals, and storage materials for nuclear wastes. Here, we demonstrate that blends of the specific glass compositions studied are miscible in all proportions, an unreported phenomenon in hard condensed matter like glass. Interestingly, excellent agreement was found between the obtained data and calculated Tgs from theoretical equations (Supplementary information) for predicting the composition dependence of Tg for miscible blends with weak but significant specific interactions between the blend components. That this blending method is at present not applied to inorganic glasses reflects the fact that water and chemically resistant phosphate glasses with relatively low Tgs have become available only recently.

Gas sensing behaviour of cerium oxide and magnesium aluminate

Indian Academy of Sciences (India)

Gas sensing behaviour of cerium oxide and magnesium aluminate composites ... A lone pairof the electron state was identified from the electro paramagnetic ... carbon monoxide (CO) (at 0.5, 1.0 and 1.5 bar) and ethanol (at 50 and 100 ppm) was ... The magnitude of the temperature varied linearly regardless of the gas ...

Lithium aluminate/zirconium material useful in the production of tritium

Science.gov (United States)

Cawley, W.E.; Trapp, T.J.

A composition is described useful in the production of tritium in a nuclear reactor. Lithium aluminate particles are dispersed in a matrix of zirconium. Tritium produced by the reactor of neutrons with the lithium are absorbed by the zirconium, thereby decreasing gas pressure within capsules carrying the material.

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

Directory of Open Access Journals (Sweden)

Hui Li

2013-01-01

Full Text Available A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modification by aluminate coupling agent which reduced the surface energy greatly, was found to be responsible for the superhydrophobicity. The method adopted is relatively simple, facile, and cost-effective and can potentially be applied to large water-repellent surface coatings.

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

International Nuclear Information System (INIS)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO 2 ) and lithium silicate (Li 2 SiO 3 ) by the reaction: Li 6 + n → 4 He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100 0 C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T 2 ), while in laboratory extractions (300-1300 0 C), the tritium appeared primarily in the condensible form (HTO and T 2 O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H 2 O, CO 2 , CO, O 2 , H 2 , NO, SO 2 , SiF 4 and traces of hydrocarbons

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

OpenAIRE

Qingjie Jiao; Qiushi Wang; Jianxin Nie; Xueyong Guo; Wei Zhang; Wenqi Fan

2018-01-01

To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20) based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-...

Criterion for selection the optimal physical and chemical properties of cobalt aluminate powder used in investment casting process

Directory of Open Access Journals (Sweden)

M. Zielińska

2009-07-01

Full Text Available The aim of this work was to determine physical and chemical properties of cobalt aluminate (CoAl2O4 modifiers produced by different companies and the influence of different types of modifiers on the grain size of high temperature creep resisting superalloys: Inconel 713C, René 77 and MAR-M 509.The first stage of the research work took over the investigations of physical and chemical properties of cobalt aluminate manufactured by three different companies: Remet, Mason Color and Permedia Lublin. There were determined the grain size distribution of cobalt aluminate powder, the average diameter and morphology of powder particles, phase composition, as well as sodium and cobalt content, pH value of water suspension and the bulk density. In the next step, the ceramic moulds were made with different kind of cobalt aluminate (Mason Color, Remet, Permedia Lublin and its concentration (0, 5% in the primary slurry. The samples of stepped shape were poured in the ceramic moulds prepared earlier. The average grain size of the γ phase was determined on the stepped samples.It was established that physical and chemical properties of cobalt aluminate modifier are different up to the manufacturer. For example the modifiers manufactured by Permedia; Mason Color and Remet companies have different the average diameter of particles- 68,050d; 49,6 i 36,7μm, and also cobalt content _CoC=32,53%; 39,43% i 34,79%mass, respectively. The grain size of γ matrix of superalloys depends on the kind of used inoculant. The best grain refinement of the matrix of superalloys: Inconel 713C, René 77 and MAR-M 509 was observed in the castings modified with the use of Mason Color modifier. On the grounds of literature data and obtained results it was established that the cobalt content of cobalt aluminate influences the intensity of nucleation process during the crystallization of superalloys: Inconel 713C, René 77 i MAR-M 509.

EFFECT OF COMMERCIALLY MANUFACTURED KAPPA SEMI-REFINED CARRAGEENAN (SRC WITH DIFFERENT PHOSPHATE SALTS ON YIELD, TEXTURAL AND SENSORY PROPERTIES OF BEEF MEAT

Directory of Open Access Journals (Sweden)

Marimuthu Murugesan

2016-06-01

Full Text Available The phosphate salts such as SDP, TSP, SHMP, DSP, TPPP, TKPP and STPP were blended with semi-refined kappa carrageenan (SRC individually and their aqueous solution was injected into the fresh beef meat. The highest weight gain (24% in fresh meat was obtained from injection of blend made with SRC and STPP as compared to other blends and control sample after forzen storage. Similarly, it also showed low cooking loss (24% with good testural and sensory proerties as compared to other blends. It can be concluded from the presnt study that blend of SRC and STPP can be used in beef meat for yield and quality improvement.

Dielectric behavior and ac electrical conductivity of nanocrystalline nickel aluminate

International Nuclear Information System (INIS)

Kurien, Siby; Mathew, Jose; Sebastian, Shajo; Potty, S.N.; George, K.C.

2006-01-01

Nanocrystalline nickel aluminate was prepared by chemical co-precipitation, and nanoparticles having different particle size were obtained by annealing the precursor at different temperatures. The TG/DTA measurements showed thermal decomposition was a three-step process with crystallisation of the spinel phase started at a temperature 420 deg. C. The X-ray diffraction analysis confirmed that the specimen began to crystallise on annealing above 420 deg. C and became almost crystalline at about 900 deg. C. The particle sizes were calculated from XRD. Dielectric properties of nickel aluminate were studied as a function of the frequency of the applied ac signal at different temperatures. It was seen the real dielectric constant ε', and dielectric loss tan δ decreased with frequency of applied field while the ac conductivity increased as the frequency of the applied field increased. The dielectric relaxation mechanism is explained by considering nanostructured NiAl 2 O 4 as a carrier-dominated dielectric with high density of hopping charge carriers. The variation of ε' with different particle size depends on several interfacial region parameters, which change with the average particle size

Quantitative analysis for the determination of aluminum percentage and detonation performance of aluminized plastic bonded explosives by laser-induced breakdown spectroscopy

Science.gov (United States)

Rezaei, A. H.; Keshavarz, M. H.; Kavosh Tehrani, M.; Darbani, S. M. R.

2018-06-01

The aluminized plastic-bonded explosive (PBX) is a composite material in which solid explosive particles are dispersed in a polymer matrix, which includes three major components, i.e. polymeric binder, metal fuel (aluminum) and nitramine explosive. This work introduces a new method on the basis of the laser-induced breakdown spectroscopy (LIBS) technique in air and argon atmospheres to investigate the determination of aluminum content and detonation performance of aluminized PBXs. Plasma emissions of aluminized PBXs are recorded where atomic lines of Al, C and H as well as molecular bands of AlO and CN are identified. The experimental results demonstrate that a good discrimination and separation between the aluminized PBXs is possible using LIBS and principle component analysis, although they have similar atomic composition. Relative intensity of the AlO/Al is used to determine aluminum percentage of the aluminized PBXs. The obtained quantitative calibration curve using the relative intensity of the AlO/Al is better than the resulting calibration curve using only the intensity of Al. By using the LIBS method and the measured intensity ratio of CN/C, an Al content of 15% is found to be the optimum value in terms of velocity of detonation of the RDX/Al/HTPB standard samples.

Calcium aluminates for quick cesium trapping, application for nuclear power plants

International Nuclear Information System (INIS)

Capmas, A.; Dubourg, M.; Boch, P.

1993-01-01

It has recently been shown that cesium dissolved in water could be trapped in a solid structure by adding cementitious calcium aluminates and fume silica. Calcium aluminates are heat resistant and widely used as refractory products. Extensive studies on the rheological properties has been achieved. It is now possible to obtain flow properties to such an extent as to percolate a slurry through broken structures and give high mechanical strength in a short time. This along with the other properties of thermal shock resistance and cesium trapping makes a solution possible for nuclear building safety as a preventitive or a curative material. For example, at Chernobyl, this material could improve safety by remote casting techniques, construction of a structure which could serve as as ash tray under the coruim. Remotelly controlled equipment needed for this are in operation in more than 50 standardized PWR's. The equipment performs maintenance and inspection tasks with low radiation exposure

Reactivity of non-stoichiometric black alumina; Reactivite des alumines noires non stoechiometriques

Energy Technology Data Exchange (ETDEWEB)

Arghiropoulos, B; Elston, J; Hilaire, P; Juillet, F; Teichner, S J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; [Lyon-1 Univ., 69 (France)

1960-07-01

Oxides such as alumina, when divided or poorly crystallized, show enhanced physico-chemical properties with respect to those of non-divided crystals of the same solids. A stoichiometric difference may even be produced in the alumina, which brings about a new modification of its properties. However its characteristics of hydrogen chemisorption or of catalytic activity in ethylene hydrogenation do not appear to depend on the stoichiometric difference. (author) [French] Les oxydes, comme l'alumine, divises ou mal cristallises, presentent des proprietes physico-chimiques exaltees par rapport a celles des memes solides en cristaux non divises. Un ecart a la stoechiometrie peut meme etre produit dans l'alumine, ce qui entraine une nouvelle modification de ses proprietes. Toutefois ses caracteristiques de chimisorption d'hydrogene ou d'activite catalytique d'hydrogenation d'ethylene ne semblent pas dependre de l'ecart a la stoechiometrie. (auteur)

Carbonation of calcium aluminate cement pastes

Directory of Open Access Journals (Sweden)

Fernández-Carrasco, L.

2001-12-01

Full Text Available This work discusses the results from accelerated tests intended to investigate the ways the different curing methods affect the carbonation of calcium aluminate cements pastes (CAC. The research was focused on the mineralogical composition of hydrated and carbonated samples. The compressive strengths and the porosity of the samples have been determined. Results point out that vaterite and aragonite are formed as a result of carbonation of both cubic and hexagonal calcium aluminate hydrates. The polymorph of calcium carbonate formed does not depend on the curing process. Carbonation rates is higher in hexagonal than in cubic hydrates. Results obtained through this study evidence that, as a consequence of the carbonation process of CAC pastes, in test conditions, an increase of the mechanical strengths occurs.

En el presente trabajo se discuten los resultados obtenidos en los ensayos acelerados llevados a cabo para investigar los efectos de diferentes métodos de curado sobre la carbonatacion de pastas del cemento de aluminato de calcio (CAC. Se estudió la composición mineralógica de las muestras hidratadas y carbonatadas. Además, se determinaron las resistencias mecánicas a compresión y la porosidad de las probetas. Los resultados indican que la vaterita y el aragonito son las polimorfías del CaCO₃ que se forman al carbonatar los aluminatos cálcicos hidratos, tanto los de naturaleza hexagonal como cúbica. El polimorfo del carbonato cálcico formado no depende del proceso de curado. La velocidad de carbonatación de los hidratos hexagonales es mayor que la de los cúbicos. Los resultados obtenidos en el presente trabajo han evidenciado que como consecuencia del proceso de carbonatación sobre pastas de CAC, en las condiciones realizadas, se produce un incremento en las resistencias mecánicas.

Physical and Mechanical Properties of Composites Made with Aluminous Cement and Basalt Fibers Developed for High Temperature Application

Directory of Open Access Journals (Sweden)

Pavel Reiterman

2015-01-01

Full Text Available Present paper deals with the experimental study of the composition of refractory fiber-reinforced aluminous cement based composites and its response to gradual thermal loading. Basalt fibers were applied in doses of 0.25, 0.5, 1.0, 2.0, and 4.0% in volume. Simultaneously, binder system based on the aluminous cement was modified by fine ground ceramic powder originated from the accurate ceramic blocks production. Ceramic powder was dosed as partial replacement of used cement of 5, 10, 15, 20, and 25%. Influence of composition changes was evaluated by the results of physical and mechanical testing; compressive strength, flexural strength, bulk density, and fracture energy were determined on the different levels of temperature loading. Increased dose of basalt fibers allows reaching expected higher values of fracture energy, but with respect to results of compressive and flexural strength determination as an optimal rate of basalt fibers dose was considered 0.25% in volume. Fine ground ceramic powder application led to extensive increase of residual mechanical parameters just up to replacement of 10%. Higher replacement of aluminous cement reduced final values of bulk density but kept mechanical properties on the level of mixtures without aluminous cement replacement.

The morphology of coating/substrate interface in hot-dip-aluminized steels

International Nuclear Information System (INIS)

Awan, Gul Hameed; Hasan, Faiz ul

2008-01-01

In hot-dip-aluminized (HAD) steels, the morphology and the profile of the interface between the aluminum coating and the substrate steel, are affected both by the composition of the molten aluminum as well as by the composition, and even the microstructure, of the substrate steel. This effect has been investigated using optical and scanning electron microscopy, and X-ray diffraction. The reaction between the steel and the molten aluminum leads to the formation of Fe-Al inter-metallic compounds on the steel surface. The thickness of the inter-metallic compound layer as well as the morphology of the interface between the steel and the interlayer varies with the silicon content of the molten aluminum. In hot-dip-aluminizing with pure aluminum, the interlayer is 'thick' and exhibits a finger-like growth into the steel. With a gradually increasing addition of silicon into the aluminum melt, the thickness of the interlayer decreases while the interface between the interlayer and the substrate gradually becomes 'smoother'. With an increase in the carbon content of the substrate steel the growth of the interlayer into the steel is impeded by the pearlite phase, whereas the ferrite phase appears to dissolve more readily. X-ray diffraction and electron microscopic studies showed that the interlayer formed in samples aluminized in pure aluminum, essentially consisted of orthorhombic Fe 2 Al 5 . It was further observed that the finger-like grains of Fe 2 Al 5 phase exhibited a preferred lattice orientation. With a gradual addition of silicon into the aluminum melt, a cubic phase based on Fe 3 Al also started to form in the interlayer and replaced most of the Fe 2 Al 5

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

Energy Technology Data Exchange (ETDEWEB)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO/sub 2/) and lithium silicate (Li/sub 2/SiO/sub 3/) by the reaction: Li/sup 6/ + n ..-->.. /sup 4/He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100/sup 0/C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T/sub 2/), while in laboratory extractions (300-1300/sup 0/C), the tritium appeared primarily in the condensible form (HTO and T/sub 2/O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H/sub 2/O, CO/sub 2/, CO, O/sub 2/, H/sub 2/, NO, SO/sub 2/, SiF/sub 4/ and traces of hydrocarbons.

Data and properties of lithium aluminate γ LiAlO2

International Nuclear Information System (INIS)

Denuziere, C.; Roux, N.

1988-01-01

In this report are gathered and analysed the literature data until july 1st, 1984, concerning the properties of lithium aluminate γ LiAlO 2 relevant for the investigation of this compound as a tritum breeding material for a fusion reactor blanket. A french version of this report exists

Effect of Coating-thickness on the formability of hot dip aluminized steel

International Nuclear Information System (INIS)

Awan, G.H.; Ahmed, F.; Hasan, F.

2008-01-01

The influence of coating thickness on the formability and ductility of hot-dip-aluminized steel has been determined using a 3-point bend test and optical metallography. The ductility / formability was estimated from the 3-point bend test wherein the angle of bend at which the cracks start to appear on the surface of the aluminized sheet during bending, was taken as an index of the formability / ductility. It was observed that as the amount of silicon in the aluminising melt was gradually increased the measured ductility of the sheet sample also increased. Metallographic examination has shown that as the amount of silicon in the aluminising melt was increased the thickness of the intermediate compound layer, between the outer aluminum coat and the substrate steel, decreased. It was thus indicated from these experiments that the formability / ductility of the sheet was inversely related to the thickness of the interlayer. (author)

Age and geochemistry of Alumine's Ignimbrites, Neuquen province, Argentina

International Nuclear Information System (INIS)

Lagorio, Silvia; Massaferro, Gabriela

1998-01-01

Geochemical and geochronological data from Alumine riolitic welded tuffs are analysed. Minor elements show enrichment in Rb, Th and K and depletion in Nb, Ti, P and Sr. La/Yb ratios are low. The geochemical features are consistent with a volcanic arc genesis. The radiometric data obtained by K/Ar method point out a Paleocene age for these rocks, allowing to correlate them with the Ventana Formation or the equivalent Auca Pan Formation. (author)

Electrical properties and thermal expansion of strontium aluminates

Energy Technology Data Exchange (ETDEWEB)

Zakharchuk, K.V. [Department of Materials and Ceramic Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Yaremchenko, A.A., E-mail: ayaremchenko@ua.pt [Department of Materials and Ceramic Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Fagg, D.P. [TEMA-NRD, Mechanical Engineering Department, University of Aveiro, 3810-193 Aveiro (Portugal)

2014-11-15

Highlights: • Sr{sub 3}Al{sub 2}O{sub 6}, SrAl{sub 2}O{sub 4} and Sr{sub 4}Al{sub 14}O{sub 25} ceramics are semiconductors. • Electrical conductivity is as low as 10{sup −6}−4×10{sup −5} S/cm at 1273 K in dry air. • SrAl{sub 2}O{sub 4} is a mixed conductor with predominant ionic conductivity. • Sr{sub 3}Al{sub 2}O{sub 6} shows significant contribution of protonic transport in wet atmospheres. • Average TECs vary in the range (8.5–11.1)×10{sup −6} K{sup −1} and are p(O{sub 2})-independent. - Abstract: Strontium aluminate ceramics, including Sr{sub 3}Al{sub 2}O{sub 6}, SrAl{sub 2}O{sub 4} and Sr{sub 4}Al{sub 14}O{sub 25}, synthesized by glycine–nitrate combustion and sintered at 1773 K in air, were characterized by thermal analysis, dilatometry and electrical measurements in controlled atmospheres. All studied strontium aluminates are semiconductors with electrical conductivities as low as 10{sup −6}−4×10{sup −5} S/cm at 1273 K in dry air. Electrical measurements in controlled atmospheres in combination with ion transference number determination demonstrated that SrAl{sub 2}O{sub 4} is a mixed conductor with predominant ionic conductivity and increasing n-type and p-type electronic contributions under highly reducing and oxidizing conditions, respectively. While the behavior of electrical conductivity of Sr{sub 3}Al{sub 2}O{sub 6} in dry atmospheres was qualitatively similar to that of SrAl{sub 2}O{sub 4}, a significant increase of conductivity in wet atmospheres was attributed to a protonic contribution to electrical conduction, in correlation with thermogravimetric data and the tendency of this material to form a hydrogarnet at low temperatures. The average thermal expansion coefficients of strontium aluminates, (8.5–11.1)×10{sup −6} K{sup −1} at 333–1373 K, increase with increasing strontium content in the sequence Sr{sub 4}Al{sub 14}O{sub 25} < SrAl{sub 2}O{sub 4} < Sr{sub 3}Al{sub 2}O{sub 6} and are essentially

Hydrate Phase Assemblages in Blends of Ye'elimite and Gypsum with Alite and Belite

DEFF Research Database (Denmark)

Pedersen, Malene Thostrup; Skibsted, Jørgen

2016-01-01

Calcium sulpho-aluminate (CSA) cements all contain ye’elimite, either as the main phase or in intermediate amounts, while they differ in their content of accessory phases. Belite is the main phase in most CSA cements, however, alite - CSA cements have been produced. The hydrate phases formed during...... and hydration kinetics. The improved understanding of the hydrate phase assemblages as well as the hydration kinetics for the model systems will form the fundamental basis for further optimizations of blended systems including ye’elimite with the aim of maximizing the reaction degree of the main clinker phases...... hydration of CSA cements depend on the type of CSA cement and the amount of gypsum added. The hydration reactions of the main phases are by themselves well documented, whereas the simultaneous hydration of CSA cement components is not fully understood in terms of hydration products and kinetics. To further...

Criterion for selection the optimal physical and chemical properties of cobalt aluminate powder used in investment casting process

OpenAIRE

M. Zielińska; J. Sieniawski; B. Gajecka

2009-01-01

The aim of this work was to determine physical and chemical properties of cobalt aluminate (CoAl2O4) modifiers produced by different companies and the influence of different types of modifiers on the grain size of high temperature creep resisting superalloys: Inconel 713C, René 77 and MAR-M 509.The first stage of the research work took over the investigations of physical and chemical properties of cobalt aluminate manufactured by three different companies: Remet, Mason Color and Permedia Lubl...

Studies of PVC/ENR blends: blend compositions

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

2002-01-01

Blends of poly(vinyl chloride/epoxidized natural rubber (PVC/ENR) were prepared by using Bra bender Plasticorder at compositions ranging from 0-100% PVC. They were blended at 150 degree C mixing temperature, 50 rpm rotor speed and 10 minutes mixing time. The blends were characterized for tensile strength , elongation at break, glass transition temperatures and Fourier transform infra red spectroscopy (FTIR). Results revealed that as the PVC content increases the blend behaviour changes from elastomeric to glassy. However the blends found to be compatible at all compositions. (Author)

Methods of use of calcium hexa aluminate refractory linings and/or chemical barriers in high alkali or alkaline environments

Science.gov (United States)

McGowan, Kenneth A; Cullen, Robert M; Keiser, James R; Hemrick, James G; Meisner, Roberta A

2013-10-22

A method for improving the insulating character/and or penetration resistance of a liner in contact with at least one of an alkali and/or alkaline environments is provided. The method comprises lining a surface that is subject to wear by an alkali environment and/or an alkaline environment with a refractory composition comprising a refractory aggregate consisting essentially of a calcium hexa aluminate clinker having the formula CA.sub.6, wherein C is equal to calcium oxide, wherein A is equal to aluminum oxide, and wherein the hexa aluminate clinker has from zero to less than about fifty weight percent C.sub.12A.sub.7, and wherein greater than 98 weight percent of the calcium hexa aluminate clinker having a particle size ranging from -20 microns to +3 millimeters, for forming a liner of the surface. This method improves the insulating character/and or penetration resistance of the liner.

Hydration process for calcium-aluminate cement within EVA emulsion by SPring-8 synchrotron radiation x-ray diffraction method

International Nuclear Information System (INIS)

Kotera, Masaru; Matsuda, Ikuyo; Miyashita, Keiko; Adachi, Nobuyuki; Tamura, Hisayuki

2005-01-01

Polymer-modified mortars which consist of a polymer emulsion and cement materials have been widely developed in the construction materials fields. Forming process of the polymer-modified cement membrane simultaneously involves evaporation of water within the polymer emulsion and hydration of cement. It is important for the polymer-modified cement paste that the hydrate crystal of cement is generating by the hydration during the setting process under existence of the polymer emulsion. In this study, hydration process for calcium-aluminate cement under existence of poly (ethylene-vinyl acetate) (EVA) emulsion (polymer-cement ratio=100%) was investigated by X-ray diffraction method using synchrotron radiation (SPring-8). The diffraction peaks of calcium aluminate (CA) disappeared after the hardening, on the other hand, the peaks of hydrate crystals of calcium-aluminate cement (C 2 AH 8 and C 3 AH 6 ) could be observed. This polymer-modified cement paste hydrated using the water within the polymer emulsion. The hydration of C 2 AH 8 from CA started at around 300 min, and then C 3 AH 6 hydrate crystal increased after 700 min at ambient temperature. This implies that the conversion from C 2 AH 8 to C 3 AH 6 occurred to be more stable phase. The setting temperature affected the reaction rate. In case of hydration at 35degC, the start time of the hydration for calcium-aluminate cement was quicker than that in the ambient temperature four or more times. (author)

Mechanoluminescence of Dy doped strontium aluminate nanophosphors

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ravi, E-mail: rvsharma65@gmail.com [Department of Physics, Govt. Arts and Commerce Girls College, Raipur, C.G. 492001 (India); Bisen, D.P. [School of Studies in Physics and Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Chandra, B.P. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (India)

2015-12-15

Nanosized strontium aluminate phosphors activated with Dy{sup 3+} were prepared by a combustion method. Nanophosphor was prepared by this method at reaction temperatures as low as 600 °C. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. The monoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the mechanoluminescence (ML) response curve plotted between time and ML intensity. The H{sub 3}BO{sub 3} added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl{sub 2}O{sub 4}:Dy{sup 3+} without H{sub 3}BO{sub 3.} It was found that the PL and ML intensity increases with increasing concentration of Dy, it becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} in the blue and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} in the yellow-orange wavelength region. - Highlights: • Combustion synthesis route is used to prepare the SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors. • The size of the synthesized sample was found to be in the nano-meter range. • The mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy {sup 3+} nanophosphors is studied. • The photoluminescence of SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors showed blue-shift as compared to bulk. • Effect of H{sub 3}BO{sub 3} on the mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy{sup 3+} was studied.

System and process for aluminization of metal-containing substrates

Science.gov (United States)

Chou, Yeong-Shyung; Stevenson, Jeffry W

2015-11-03

A system and method are detailed for aluminizing surfaces of metallic substrates, parts, and components with a protective alumina layer in-situ. Aluminum (Al) foil sandwiched between the metallic components and a refractory material when heated in an oxidizing gas under a compression load at a selected temperature forms the protective alumina coating on the surface of the metallic components. The alumina coating minimizes evaporation of volatile metals from the metallic substrates, parts, and components in assembled devices during operation at high temperature that can degrade performance.

System and process for aluminization of metal-containing substrates

Energy Technology Data Exchange (ETDEWEB)

Chou, Yeong-Shyung; Stevenson, Jeffry W.

2017-12-12

A system and method are detailed for aluminizing surfaces of metallic substrates, parts, and components with a protective alumina layer in-situ. Aluminum (Al) foil sandwiched between the metallic components and a refractory material when heated in an oxidizing gas under a compression load at a selected temperature forms the protective alumina coating on the surface of the metallic components. The alumina coating minimizes evaporation of volatile metals from the metallic substrates, parts, and components in assembled devices that can degrade performance during operation at high temperature.

Blend or not to blend: a study investigating faculty members perceptions of blended teaching

Directory of Open Access Journals (Sweden)

Mehmet A Ocak

2010-12-01

Full Text Available This study examined faculty members’ perceptions of blended teaching from several perspectives. A total of 73 faculty members in Turkish Higher Education context participated in the study by completing an online survey that combined quantitative and qualitative approaches. Based on a data analysis, the faculty members’ perceptions were sorted into six categories: (a satisfaction with blended teaching, (b perceived impact on the role of the faculty, (c perceived impact on student learning, (d perceived impact on student motivation, (e advantages of blended teaching, and (f disadvantages of blended teaching. Findings indicated that faculty members were likely to agree that blended teaching provides a high degree of satisfaction and that it requires more time and commitment from the faculty. The faculty members perceived that blended teaching improves student learning and, to some extent, improves motivation. The faculty members also emphasized the importance of institutional support and the use of technology to mitigate student problems. This study presents these faculty members’ perceptions, which are helpful for those planning to implement a blended teaching approach, and makes suggestions for trouble-shooting and taking advantage of the opportunities in a blended environment successfully.

Driving Ability of HMX based Aluminized Explosive Affected by the Reaction Degree of Aluminum Powder

Science.gov (United States)

Duan, Yingliang

2017-06-01

Due to the time scale of aluminum reaction, the detonation process of the aluminized explosive becomes very complex, and there is less agreement on the reaction mechanism of aluminum powder. If the reaction of aluminum occurs in the reaction zone, the energy released will further strengthen the work ability of detonation wave. So it is very important for characterizing the detonation parameters and detonation driving ability to accurately understand the role of aluminum powder in the reaction zone. In this paper, detonation driving process of HMX based aluminized explosive was studied by cylinder test, obtaining the expansion track of cylinder wall. In order to further research the reaction degree (λ) of aluminum in the reaction zone, the thermodynamic program VHL was used to calculate the detonation process at different reaction degrees, obtaining the parameters of detonation products thermodynamic state. Using the dynamic software LS-DYNA and the JWL equation of state by fitting the pressure and relative volume relationship, the cylinder test was simulated. Compared with the experimental results, when the reaction degree is 20%, the driving ability is found to be in agreement with measured ones. It is concluded that the driving ability of HMX based aluminized explosive can be more accurately characterized by considering the reaction degree of aluminum powder in the reaction zone.

Charge division in a small proportional chamber constructed with aluminized mylar tubes

International Nuclear Information System (INIS)

Biino, C.; Mussa, R.; Palestini, S.; Pastrone, N.; Pesando, L.

1988-01-01

A tracking detector composed of aluminized mylar drift tubes is under development for the Fermilab experiment 760. A prototype chamber has been constructed. Results on the longitudinal coordinate determined by charge division are given. Spatial resolution values below 2 mm (rms) were found, corresponding to <1% of the chamber length. Results on chamber ageing are also discussed. (orig.)

Charge division in a small proportional chamber constructed with aluminized mylar tubes

Science.gov (United States)

Biino, C.; Mussa, R.; Palestini, S.; Pastrone, N.; Pesando, L.

1988-09-01

A tracking detector composed of aluminized mylar drift tubes is under development for the Fermilab experiment 760. A prototype chamber has been constructed. Results on the longitudinal coordinate determined by charge division are given. Spatial resolution values below 2 mm (rms) were found, corresponding to <1% of the chamber length. Results on chamber ageing are also discussed.

Boundary conditions for diffusion in the pack-aluminizing of nickel.

Science.gov (United States)

Sivakumar, R.; Seigle, L. L.; Menon, N. B.

1973-01-01

The surface compositions of nickel specimens coated for various lengths of time in aluminizing packs at 2000 F were studied, in order to obtain information about the kinetics of the pack-cementation process in the formation of aluminide coatings. The results obtained indicate that the surface compositions of the coated nickel specimens are independent of time, at least for time between 0.5 and 20 hrs. Another important observation is that the specimens gained weight during the coating process.

Aluminized film, seam sealing tests and observations. Final report

Energy Technology Data Exchange (ETDEWEB)

1994-06-16

The purpose of this work was to investigate various seam sealing techniques, reinforcing methods, fitting installations, seam tolerances and geometric configurations pertinent to an aluminized plastic laminate. The program seeks a successful fabricating method for producing low-diffusion, cylindrical, spar liners to contain pressurized GH{sub 2} and GO{sub 2}. The test plan included: (1) seaming techniques on metallized Mylar film; (2) ``double patches`` for end fittings; (3) stainless steel bulkhead fitting assembly with seals; (4) minimum run tolerance on linear shear seam; (5) peel seam vs. inverted seal seam fabrication.

Molybdeno-Aluminizing of Powder Metallurgy and Wrought Ti and Ti-6Al-4V alloys by Pack Cementation process

International Nuclear Information System (INIS)

Tsipas, Sophia A.; Gordo, Elena

2016-01-01

Wear and high temperature oxidation resistance of some titanium-based alloys needs to be enhanced, and this can be effectively accomplished by surface treatment. Molybdenizing is a surface treatment where molybdenum is introduced into the surface of titanium alloys causing the formation of wear-resistant surface layers containing molybdenum, while aluminizing of titanium-based alloys has been reported to improve their high temperature oxidation properties. Whereas pack cementation and other surface modification methods have been used for molybdenizing or aluminizing of wrought and/or cast pure titanium and titanium alloys, such surface treatments have not been reported on titanium alloys produced by powder metallurgy (PM). Also a critical understanding of the process parameters for simultaneous one step molybdeno-aluminizing of titanium alloys by pack cementation and the predominant mechanism for this process have not been reported. The current research work describes the surface modification of titanium and Ti-6Al-4V prepared by PM by molybdeno-aluminizing and analyzes thermodynamic aspects of the deposition process. Similar coatings are also deposited to wrought Ti-6Al-4V and compared. Characterization of the coatings was carried out using scanning electron microscopy and x-ray diffraction. For both titanium and Ti-6Al-4V, the use of a powder pack containing ammonium chloride as activator leads to the deposition of molybdenum and aluminium into the surface but also introduces nitrogen causing the formation of a thin titanium nitride layer. In addition, various titanium aluminides and mixed titanium aluminium nitrides are formed. The appropriate conditions for molybdeno-aluminizing as well as the phases expected to be formed were successfully determined by thermodynamic equilibrium calculations. - Highlights: •Simultaneous co-deposition of Mo-Al onto powder metallurgy and wrought Ti alloy •Thermodynamic calculations were used to optimize deposition conditions

Molybdeno-Aluminizing of Powder Metallurgy and Wrought Ti and Ti-6Al-4V alloys by Pack Cementation process

Energy Technology Data Exchange (ETDEWEB)

Tsipas, Sophia A., E-mail: stsipas@ing.uc3m.es; Gordo, Elena

2016-08-15

Wear and high temperature oxidation resistance of some titanium-based alloys needs to be enhanced, and this can be effectively accomplished by surface treatment. Molybdenizing is a surface treatment where molybdenum is introduced into the surface of titanium alloys causing the formation of wear-resistant surface layers containing molybdenum, while aluminizing of titanium-based alloys has been reported to improve their high temperature oxidation properties. Whereas pack cementation and other surface modification methods have been used for molybdenizing or aluminizing of wrought and/or cast pure titanium and titanium alloys, such surface treatments have not been reported on titanium alloys produced by powder metallurgy (PM). Also a critical understanding of the process parameters for simultaneous one step molybdeno-aluminizing of titanium alloys by pack cementation and the predominant mechanism for this process have not been reported. The current research work describes the surface modification of titanium and Ti-6Al-4V prepared by PM by molybdeno-aluminizing and analyzes thermodynamic aspects of the deposition process. Similar coatings are also deposited to wrought Ti-6Al-4V and compared. Characterization of the coatings was carried out using scanning electron microscopy and x-ray diffraction. For both titanium and Ti-6Al-4V, the use of a powder pack containing ammonium chloride as activator leads to the deposition of molybdenum and aluminium into the surface but also introduces nitrogen causing the formation of a thin titanium nitride layer. In addition, various titanium aluminides and mixed titanium aluminium nitrides are formed. The appropriate conditions for molybdeno-aluminizing as well as the phases expected to be formed were successfully determined by thermodynamic equilibrium calculations. - Highlights: •Simultaneous co-deposition of Mo-Al onto powder metallurgy and wrought Ti alloy •Thermodynamic calculations were used to optimize deposition conditions

Inorganic Corrosion-Inhibitive Pigments for High-Temperature Alkali-activated Well Casing Foam Cement

Energy Technology Data Exchange (ETDEWEB)

Sugama, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Pyatina, T. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2014-11-14

This study evaluates inorganic pigments for improving carbon steel (CS) brine-corrosion protection by the sodium metasilicate-activated calcium aluminate cement/Fly Ash blend at 300°C. Calcium borosilicate (CBS) and zinc phosphate, significantly improved CS corrosion-protection by decreasing cement’s permeability for corrosive ions and inhibiting anodic corrosion. An amorphous Na₂O-Al₂O₃-SiO₂-H₂O phase tightly attached to CS surface formed at 300oC in CBS-modified cement pore solution. The corrosion rate of the CS covered with this phase was nearly 4-fold lower than in the case of nonmodified cement pore solution where the major phase formed on the surface of CS was crystalline analcime.

Inorganic Corrosion-Inhibitive Pigments for High-Temperature Alkali-activated Well Casing Foam Cement

Energy Technology Data Exchange (ETDEWEB)

Sugama, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Pyatina, T. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2014-11-01

This study evaluates inorganic pigments for improving carbon steel (CS) brine-corrosion protection by the sodium metasilicate-activated calcium aluminate cement/Fly Ash blend at 300°C. Calcium borosilicate (CBS) and zinc phosphate, significantly improved CS corrosion-protection by decreasing cement’s permeability for corrosive ions and inhibiting anodic corrosion. An amorphous Na₂O-Al₂O₃-SiO₂-H₂O phase tightly attached to CS surface formed at 300oC in CBS-modified cement pore solution. The corrosion rate of the CS covered with this phase was nearly 4-fold lower than in the case of nonmodified cement pore solution where the major phase formed on the surface of CS was crystalline analcime.

Low frequency dielectric relaxation processes and ionic conductivity of montmorillonite clay nanoparticles colloidal suspension in poly(vinyl pyrrolidone−ethylene glycol blends

Directory of Open Access Journals (Sweden)

2008-11-01

Full Text Available The dielectric dispersion behaviour of montmorillonite (MMT clay nanoparticles colloidal suspension in poly(vinyl pyrrolidone-ethylene glycol (PVP-EG blends were investigated over the frequency range 20 Hz to 1 MHz at 30°C. The 0, 1, 2, 3, 5 and 10 wt% MMT clay concentration of the weight of total solute (MMT+PVP were prepared in PVP-EG blends using EG as solvent. The complex relative dielectric function, alternating current (ac electrical conductivity, electric modulus and impedance spectra of these materials show the relaxation processes corresponding to the micro-Brownian motion of PVP chain, ion conduction and electrode polarization phenomena. The real part of ac conductivity spectra of these materials obeys Jonscher power law σ′(ω =σdc + Aωn in upper frequency end of the measurement, whereas dispersion in lower frequency end confirms the presence of electrode polarization effect. It was observed that the increase of clay concentration in the PVP-EG blends significantly increases the ac conductivity values, and simultaneously reduces the ionic conductivity relaxation time and electric double layer relaxation time, which suggests that PVP segmental dynamics and ionic motion are strongly coupled. The intercalation of EG structures in clay galleries and exfoliation of clay sheets by adsorption of PVP-EG structures on clay surfaces are discussed by considering the hydrogen bonding interactions between the hydroxyl group (–OH of EG molecules, carbonyl group (C=O of PVP monomer units, and the hydroxylated aluminate surfaces of the MMT clay particles. Results suggest that the colloidal suspension of MMT clay nano particles in the PVP-EG blends provide a convenient way to obtain an electrolyte solution with tailored electrical conduction properties.

Osteogenic differentiation of stem cells from human exfoliated deciduous teeth on poly(ε-caprolactone) nanofibers containing strontium phosphate

Energy Technology Data Exchange (ETDEWEB)

Su, Wen-Ta, E-mail: f10549@ntut.edu.tw [Department of Chemical Engineering and Biotechnology, National Taipei University of Technology, Taipei, Taiwan (China); Wu, Pai-Shuen [Department of Chemical Engineering and Biotechnology, National Taipei University of Technology, Taipei, Taiwan (China); Huang, Te-Yang [Department of Orthopedic Surgery, Mackay Memorial Hospital, Taipei, Taiwan (China)

2015-01-01

Mimicking the architecture of the extracellular matrix is an effective strategy for tissue engineering. Composite nanofibers similar to natural bone structure can be prepared via an electrospinning technique and used in biomedical applications. Stem cells from human exfoliated deciduous teeth (SHEDs) can differentiate into multiple cell lineages, such as cells that are alternative sources of stem cells for tissue engineering. Strontium has important functions in bone remodeling; for example, this element can simulate bone formation and decrease bone resorption. Incorporating strontium phosphate into nanofibers provides a potential material for bone tissue engineering. This study investigated the potential of poly(ε-caprolactone) (PCL) nanofibers coated or blended with strontium phosphate for the osteogenic differentiation of SHEDs. Cellular morphology and MTT assay revealed that nanofibers effectively support cellular attachment, spreading, and proliferation. Strontium-loaded PCL nanofibers exhibited higher expressions of collagen type I, alkaline phosphatase, biomineralization, and bone-related genes than pure PCL nanofibers during the osteogenic differentiation of SHEDs. This study demonstrated that strontium can be an effective inducer of osteogenesis for SHEDs. Understanding the function of bioceramics (such as strontium) is useful in designing and developing strategies for bone tissue engineering. - Highlights: • SHEDs have been considered as alternative sources of adult stem cells in tissue engineering. • Strontium phosphate into nanofibers provides a potential material for bone tissue engineering. • Nanofibers coated or blended with strontium phosphate for the osteogenic differentiation of SHEDs.

Osteogenic differentiation of stem cells from human exfoliated deciduous teeth on poly(ε-caprolactone) nanofibers containing strontium phosphate

International Nuclear Information System (INIS)

Su, Wen-Ta; Wu, Pai-Shuen; Huang, Te-Yang

2015-01-01

Mimicking the architecture of the extracellular matrix is an effective strategy for tissue engineering. Composite nanofibers similar to natural bone structure can be prepared via an electrospinning technique and used in biomedical applications. Stem cells from human exfoliated deciduous teeth (SHEDs) can differentiate into multiple cell lineages, such as cells that are alternative sources of stem cells for tissue engineering. Strontium has important functions in bone remodeling; for example, this element can simulate bone formation and decrease bone resorption. Incorporating strontium phosphate into nanofibers provides a potential material for bone tissue engineering. This study investigated the potential of poly(ε-caprolactone) (PCL) nanofibers coated or blended with strontium phosphate for the osteogenic differentiation of SHEDs. Cellular morphology and MTT assay revealed that nanofibers effectively support cellular attachment, spreading, and proliferation. Strontium-loaded PCL nanofibers exhibited higher expressions of collagen type I, alkaline phosphatase, biomineralization, and bone-related genes than pure PCL nanofibers during the osteogenic differentiation of SHEDs. This study demonstrated that strontium can be an effective inducer of osteogenesis for SHEDs. Understanding the function of bioceramics (such as strontium) is useful in designing and developing strategies for bone tissue engineering. - Highlights: • SHEDs have been considered as alternative sources of adult stem cells in tissue engineering. • Strontium phosphate into nanofibers provides a potential material for bone tissue engineering. • Nanofibers coated or blended with strontium phosphate for the osteogenic differentiation of SHEDs

Evaluation of novel micronized encapsulated essential oil-containing phosphate and lactate blends for growth inhibition of Listeria monocytogenes and Salmonella on poultry bologna, pork ham, and roast beef ready-to-eat deli loaves.

Science.gov (United States)

Casco, G; Taylor, T M; Alvarado, C

2015-04-01

Essential oils and their constituents are reported to possess potent antimicrobial activity, but their use in food processing is limited because of low solubility in aqueous systems and volatilization during processing. Two proprietary noncommercial essential oil-containing phosphate blends were evaluated for antimicrobial activity against Salmonella enterica cocktail (SC)-and Listeria monocytogenes (Lm)-inoculated deli meat products made from pork, poultry, or beef. Four treatments were tested on restructured cured pork ham, emulsified chicken bologna, and restructured beef loaf: nonencapsulated essential oil with phosphate version 1 at 0.45% of final batch (EOV145; chicken and pork, or EEOV245 beef), micronized encapsulated essential oil with phosphate version 2 at 0.60% of final batch (EEOV260), a 2.0% potassium lactate (PL) control, and a negative control (CN) with no applied antimicrobial agent. Compared with the CN, none of the antimicrobial agents (EEOV260, EOV145, PL) successfully limited Lm or SC growth to deli loaves, the EEOV260 inhibited growth of SC at days 21 and 28 to the same level of efficacy as PL (0.5 log cycle). In roast beef samples, on day 35, the SC growth was inhibited ca. 0.5 log CFU/g by EEOV260 when compared with the CN. In conclusion the EEOV260 can function to replace PL to limit Salmonella and Lm growth in ready-to-eat deli products. Further testing is needed to ensure consumer acceptability.

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

Directory of Open Access Journals (Sweden)

Qingjie Jiao

2018-03-01

Full Text Available To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20 based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-kilogram explosives in order to investigate the explosion energy released from CL-20 and Octogen (HMX based aluminized explosives. The percentage of the explosive varied from 5% to 30% and it is shown that: the shockwave peak pressure (pm grows gradually; shock wave energy (Es continues increasing, bubble energy (Eb increases then decreases peaking at 15% for both formulas, and the total energy (E and energy release rate (η peak at 20% for CL-20 and 15% for HMX. This paper outlines the physical mechanism of Eb change under the influence of an aluminium initial reaction temperature and reaction active detonation product percentage coupling. The result shows that CL-20 is superior as a new high explosive and has promising application prospects in the regulation of explosive energy output for underwater explosives.

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

Science.gov (United States)

Jiao, Qingjie; Wang, Qiushi; Nie, Jianxin; Guo, Xueyong; Zhang, Wei; Fan, Wenqi

2018-03-01

To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20) based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-kilogram explosives in order to investigate the explosion energy released from CL-20 and Octogen (HMX) based aluminized explosives. The percentage of the explosive varied from 5% to 30% and it is shown that: the shockwave peak pressure (pm) grows gradually; shock wave energy (Es) continues increasing, bubble energy (Eb) increases then decreases peaking at 15% for both formulas, and the total energy (E) and energy release rate (η) peak at 20% for CL-20 and 15% for HMX. This paper outlines the physical mechanism of Eb change under the influence of an aluminium initial reaction temperature and reaction active detonation product percentage coupling. The result shows that CL-20 is superior as a new high explosive and has promising application prospects in the regulation of explosive energy output for underwater explosives.

Carbonation-Induced Mineralogical Changes in Coal Mining Waste Blended Cement Pastes and Their Influence on Mechanical and Microporosity Properties

Directory of Open Access Journals (Sweden)

Moisés Frías

2018-04-01

Full Text Available The worldwide pursuit of new eco-efficient pozzolans is ongoing. Kaolinite-based waste is an eco-friendly source of recycled metakaolinite, a highly pozzolanic product. In this study, a blended cement paste containing 20% activated coal waste (ACW was exposed to a 100% CO2 atmosphere at 65% RH for 7 days. The variations in its phase composition and strength were studied and compared to an OPC control. Both pastes were cured for 28 days prior to the carbonation test. Reaction kinetics were assessed using XRD, SEM/EDX, TG/DTG, FT-IR, Micro-Raman spectroscopy, pore solution pH and the cumulative carbonated fraction. The blended cement carbonated 68% faster than the control. While portlandite carbonation was the main reaction in both cements, decalcification was also observed (more intensely in the 20% ACW paste in other hydraulic calcium phases (C-S-H gel, monocarboaluminate (C4AcH12, ettringite and tetracalcium aluminate (C4AH13. The end product of this reaction was calcium carbonate, mainly in the form of calcite, although traces of aragonite and amorphous carbonate were also detected. Compressive strength values rose with accelerated carbonation time and pore size reduction in both cement pastes.

Corrosion of gadolinium aluminate-aluminium oxide samples in fully desalinated water at 575 K

International Nuclear Information System (INIS)

Hattenbach, K.; Zimmermann, H.U.

1978-07-01

Corrosion tests have been carried out for 1 1/2 years on gadolinium aluminate/aluminium oxide samples (burnable poison for ship propulsion reactors) with and without cans at 575 K in fully desalinated water. It was found that this substance is highly corrosion-resistant. (orig./HP) [de

Water-sensitive positron trapping modes in nanoporous magnesium aluminate ceramics

International Nuclear Information System (INIS)

Filipecki, J; Ingram, A; Klym, H; Shpotyuk, O; Vakiv, M

2007-01-01

The water-sensitive positron trapping modes in nanoporous MgAl 2 O 4 ceramics with a spinel structure are studied. It is shown that water-sorption processes in magnesium aluminate ceramics leads to corresponding increase in positron trapping rates of extended defects located near intergranual boundaries. This catalytic affect has reversible nature, being strongly dependent on sorption water fluxes in ceramics. The fixation of all water-dependent positron trapping inputs allow to refine the most significant changes in positron trapping rate of extended defects

Water-sensitive positron trapping modes in nanoporous magnesium aluminate ceramics

Energy Technology Data Exchange (ETDEWEB)

Filipecki, J [Institute of Physics of Jan Dlugosz University, 13/15, al. Armii Krajowej, Czestochowa, PL 42201 (Poland); Ingram, A [Opole University of Technology, 75, Ozimska str., Opole, PL 45370 (Poland); Klym, H [Institute of Materials of SRC ' Carat' , 202, Stryjska str., Lviv, UA 79031 (Ukraine); Shpotyuk, O [Institute of Materials of SRC ' Carat' , 202, Stryjska str., Lviv, UA 79031 (Ukraine); Vakiv, M [Institute of Materials of SRC ' Carat' , 202, Stryjska str., Lviv, UA 79031 (Ukraine)

2007-08-15

The water-sensitive positron trapping modes in nanoporous MgAl{sub 2}O{sub 4} ceramics with a spinel structure are studied. It is shown that water-sorption processes in magnesium aluminate ceramics leads to corresponding increase in positron trapping rates of extended defects located near intergranual boundaries. This catalytic affect has reversible nature, being strongly dependent on sorption water fluxes in ceramics. The fixation of all water-dependent positron trapping inputs allow to refine the most significant changes in positron trapping rate of extended defects.

Calcium aluminate cement hydration in a high alkalinity environment

Directory of Open Access Journals (Sweden)

Palomo, Á.

2009-03-01

Full Text Available The present paper forms part of a broader research project that aims primarily to devise new cementitious products via the alkali activation of silico-aluminous materials. This work addresses the possibility of using small percentages of calcium aluminate cement (CAC as a source of reactive aluminium. For this reason, a preliminary review was needed of the behaviour of CACs in highly alkaline media (2, 8 and 12M NaOH solutions. Two, 28- and 180-day mechanical strength was determined and the reaction products were characterized with XRD and FTIR. The water-hydrated CAC was used as the control.The results obtained showed that CAC hardening took place much more slowly in highly alkaline media than in water. Nonetheless, the 28-day compressive strength obtained, ≥80MPa. As main reaction products, to ambient temperature and from the two days of cured, cubic aluminate C3AH6, and AH3 polymorphs are formed, instead of the usual hexagonal aluminatos (CAH10 and C2AH8 that are formed in the normal hydrate with water.El presente trabajo forma parte de una amplia investigación cuyo objetivo principal es el de elaborar nuevos materiales con propiedades cementantes mediante la activación alcalina de materiales de naturaleza silito-aluminosa. En estos estudios se contempla la posibilidad de utilizar pequeños porcentajes de cemento de aluminato de calcio (CAC como fuente de aluminio reactivo. Por ello inicialmente se ha estudiado el comportamiento de los CAC en medios fuertemente alcalinos (disoluciones de NaOH 2M, 8M y 12M. Se determinaron las resistencias mecánicas a 2, 28 y 180 días y se realizó una caracterización de los productos de reacción formados por DRX, FTIR. Como sistema de referencia se consideró la hidratación del CAC con agua.Los resultados obtenidos muestran que en medios fuertemente alcalinos se retrasan los procesos de rápido endurecimiento de CAC con agua. No obstante a 28 días se obtienen valores de resistencia a compresión �

Another look at the deterioration of calcium aluminate cement concrete

Directory of Open Access Journals (Sweden)

Jambor, Jaromir

1996-03-01

Full Text Available Potential degradation of concrete structures made of calcium aluminate cement (CAC is well known and is caused by transformation (conversion of the thermodynamically metastable into stable calcium aluminate hydrate phases. This recrystallization is influenced by temperature and humidity; the structural degradation of the concrete itself thus its loss of strength, is strongly related to the pore structure of the hydrated cement paste, the critical parameters being the total volume of pores below 15-20 nm and the median micropore radius. This constitutes a novel procedure for evaluation of existing CAC concrete structure.

La degradación potencial de estructuras de hormigón elaboradas con cemento aluminoso (CA es bien conocida. Este deterioro está causado por la recristalización (conversión de las fases del aluminato cálcico que son termodinámicamente metastables, en fases estables. En esta recristalización influye la temperatura y la humedad. Tanto la degradación del propio hormigón, como su pérdida de resistencias están relacionadas estrechamente con la estructura porosa de la pasta del cemento hidratado, siendo parámetros críticos el volumen total de los poros inferiores a 15-20 nm y el tamaño medio de los radios de los microporos. Esto constituye un nuevo procedimiento para evaluar las estructuras existentes de hormigón de cemento aluminoso (CA.

RELEASE AND MUCOADHESION PROPERTIES OF DICLOFENAC MATRIX TABLETS FROM NATURAL AND SYNTHETIC POLYMER BLENDS.

Science.gov (United States)

Odeniyi, Michael A; Khan, Nasir H; Peh, Kok K

2015-01-01

The delayed release and mucoadhesive properties of Cedrela gum and hydroxypropylmethylcellulose blend in diclofenac sodium tablet formulations were evaluated. Tablets were prepared by direct compression and the crushing strength and detachment force were found to increase from 74.49 ± 1.22 to 147.25 ± 2.57 N and 0.302 ± 0.36 to 1.141 ± 0.05 N from low to high level of polymers, respectively. The release kinetics followed Korsmeyer-Peppas release and the n varied between 0.834 and 1.273, indicating that the release mechanism shifts from Fickian to super case I (anomalous release). The drug release profile fits a pulsatile-release pattern characterized by a lag time followed by a more or less rapid and complete drug release. The Cedrela gum-hydroxypropylmethylcelluse blend tablets delayed diclofenac release for 2 h and sustained the release for 12 h. The polymer blend delayed drug release in the 0.1 M HCl simulating gastric environment and subsequent release pH 6.8 phosphate buffer.

The radiological impact of the Belgian phosphate industry

Energy Technology Data Exchange (ETDEWEB)

Vanmarcke, H.; Paridaens, J. [Belgian Nuclear Research Centre, SCK.CEN, Boeretang 200, 2400 Mol (Belgium)

2006-07-01

The Belgian phosphate industry processes huge amounts of phosphate ore (1.5 to 2 Mton/year) for a wide range of applications, the most important being the production of phosphoric acid, fertilizers and cattle food. Marine phosphate ores show high specific activities of the natural uranium decay series (usually indicated by Ra-226) (e.g. 1200 to 1500 Bq/kg for Moroccan ore). Ores of magmatic origin generally contain less of the uranium and more of the thorium decay series (up to 500 Bq/kg). These radionuclides turn up in by-products, residues or product streams depending on the processing method and the acid used for the acidulation of the phosphate rock. Sulfuric acid is the most widely used, but also hydrochloric acid and nitric acid are applied in Belgium. For Flanders, the northern part of Belgium, we already have a clear idea of the production processes and waste streams. The five Flemish phosphate plants, from 1920 to 2000, handled 54 million ton of phosphate ore containing 65 TBq of radium-226 and 2.7 TBq of thorium- 232. The total surface area of the phosphogypsum and calcium fluoride sludge deposits amounts to almost 300 ha. There is also environmental contamination along two small rivers receiving the waste waters of the hydrochloric production process: the Winterbeek (> 200 ha) and the Grote Laak (12 ha). The data on the impact of the phosphate industry in the Walloon provinces in Belgium is less complete. A large plant produced in 2004 0.8 Mton of phosphogypsum, valorizing about 70 % of the gypsum in building materials (plaster, cement), in fertilizers, and in other products such as paper. The remainder was stored on a local disposal site. The radiological impact of the Belgian phosphate industry on the local population will be discussed. At present most contaminated areas are still recognizable as waste deposits and inaccessible to the population. However as gypsum deposits and other contaminated areas quickly blend in with the landscape, it is

INFLUENCE OF CURING TEMPERATURE ON THE PHYSICO-MECHANICAL, CHARACTERISTICS OF CALCIUM ALUMINATE CEMENT WITH AIR-COOLED SLAG OR WATER-COOLED SLAG

Directory of Open Access Journals (Sweden)

M. Heikal

2004-12-01

Full Text Available The nature, sequence, crystallinity and microstructure of hydrated phases were analyzed using differential scanning calorimetry (DSC, X-ray diffraction (XRD and scanning electron microscopy (SEM. The results showed that the formation of different hydrated phases was temperature dependence. The physico-mechanical and microstructural characteristics were investigated after curing at 20, 40 and 60° C. The results indicated that for the substitution of calcium aluminate cement (CAC by air-cooled slag (AS or water-cooled slag (WS at 20° C, the compressive strength increases with slag content up to 10 wt.%, then followed by a decrease with further slag substitution up to 25 wt.%; but the values are still higher than those of the neat CAC pastes at different curing ages up to 60 days. After 28 days of hydration at 40-60° C, the compressive strength increases with the slag content. This is attributed to the prevention of the conversion reaction, which was confirmed by XRD, DSC and SEM techniques, and the preferential formation of stratlingite (gehleinte-like phase. The SEM micrographs showed a close texture of hydrated CAC/slag blends made with AS or WS at 40°C due to the formation of C2ASH8 and C-S-H phases.

Blended learning

DEFF Research Database (Denmark)

Dau, Susanne

2016-01-01

Blended Learning has been implemented, evaluated and researched for the last decades within different educational areas and levels. Blended learning has been coupled with different epistemological understandings and learning theories, but the fundamental character and dimensions of learning...... in blended learning are still insufficient. Moreover, blended learning is a misleading concept described as learning, despite the fact that it fundamentally is an instructional and didactic approach (Oliver & Trigwell, 2005) addressing the learning environment (Inglis, Palipoana, Trenhom & Ward, 2011......) instead of the learning processes behind. Much of the existing research within the field seems to miss this perspective. The consequence is a lack of acknowledgement of the driven forces behind the context and the instructional design limiting the knowledge foundation of learning in blended learning. Thus...

Tritium extraction from neutron-irradiated lithium aluminate.; Extraccion del tritio generado por irradiacion neutronica de aluminato de litio.

Energy Technology Data Exchange (ETDEWEB)

Garcia H, F

1995-10-01

Lithium aluminate is being strongly considered as a breeder material because of its thermophysical, chemical and mechanical stability at high temperatures and its favorable irradiation behavior. Furthermore, it is compatible with other blanket and structural materials. In this work, the effects of calcination temperature during preparation, extraction temperature and sweep gas composition were observed. Lithium aluminate prepared by four different methods, was neutron irradiated for 30 minutes at a flux of 10{sup 12} -10{sup 13} n/cm{sup 2} s in the TRIGA Mark III reactor at Salazar, Mexico; and the tritium extraction rate was measured. Calcination temperature do not affect the tritium extraction rate. However, using high calcination temperature, gamma lithium aluminate was formed. The tritium extraction at 600 Centigrade degrees was lower than at 800 Centigrade degrees and the tritium amount extracted by distillation of the solid sample was higher. The sweep gas composition showed that tritium extraction was less with Ar plus 0.5 % H{sub 2} that with Ar plus 0.1 % H{sub 2}. This result was contrary to expected, where the tritium extraction rate could be higher when hydrogen is added to the sweep gas. Probably this effect could be attributed to the gas purity. (Author).

Utilization of municipal solid waste incineration (MSWI) fly ash in blended cement

International Nuclear Information System (INIS)

Aubert, J.E.; Husson, B.; Sarramone, N.

2006-01-01

This paper is the first of a series of two articles dealing with the processes applied to MSWI fly ash with a view to reusing it safely in cement-based materials. Part 1 presents two stabilization processes and Part 2 deals with the use of the two treated fly ashes (TFA) in mortars. Two types of binder were used: an Ordinary Portland Cement (OPC) containing more than 95% clinker (CEM I 52.5R) and a binary blend cement composed of 70% ground granulated blast furnace slag and 30% clinker (CEM III-B 42.5N). In this first part, two stabilization processes are presented: the conventional process, called 'A', based on the washing, phosphation and calcination of the ash, and a modified process, called 'B', intended to eliminate metallic aluminum and sulfate contained in the ash. The physical, chemical and mineralogical characteristics of the two TFA were comparable. The main differences observed were those expected, i.e. TFA-B was free of metallic aluminum and sulfate. The mineralogical characterization of the two TFAs highlighted the presence of large amounts of a calcium aluminosilicate phase taking two forms, a crystalline form (gehlenite) and an amorphous form. Hydration studies on pastes containing mixed TFA and calcium hydroxide showed that this phase reacted with calcium hydroxide to form calcium aluminate hydrates. This formation of hydrates was accompanied by a hardening of the pastes. These results are very encouraging for the reuse of such TFA in cement-based materials because they can be considered as pozzolanic additions and could advantageously replace a part of the cement in cement-based materials. Finally, leaching tests were carried out to evaluate the environmental impact of the two TFAs. The elements which were less efficiently stabilized by process A were zinc, cadmium and antimony but, when the results of the leaching tests were compared with the thresholds of the European landfill directive, TFA-A could nevertheless be accepted at landfills for non

Utilization of municipal solid waste incineration (MSWI) fly ash in blended cement

Energy Technology Data Exchange (ETDEWEB)

Aubert, J.E. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France)]. E-mail: aubert@insa-toulouse.fr; Husson, B. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France); Sarramone, N. [Laboratoire Materiaux et Durabilite des Constructions (L.M.D.C.), INSA-UPS, 135 avenue de Rangueil, 31077 Toulouse cedex 4 (France)

2006-08-25

This paper is the first of a series of two articles dealing with the processes applied to MSWI fly ash with a view to reusing it safely in cement-based materials. Part 1 presents two stabilization processes and Part 2 deals with the use of the two treated fly ashes (TFA) in mortars. Two types of binder were used: an Ordinary Portland Cement (OPC) containing more than 95% clinker (CEM I 52.5R) and a binary blend cement composed of 70% ground granulated blast furnace slag and 30% clinker (CEM III-B 42.5N). In this first part, two stabilization processes are presented: the conventional process, called 'A', based on the washing, phosphation and calcination of the ash, and a modified process, called 'B', intended to eliminate metallic aluminum and sulfate contained in the ash. The physical, chemical and mineralogical characteristics of the two TFA were comparable. The main differences observed were those expected, i.e. TFA-B was free of metallic aluminum and sulfate. The mineralogical characterization of the two TFAs highlighted the presence of large amounts of a calcium aluminosilicate phase taking two forms, a crystalline form (gehlenite) and an amorphous form. Hydration studies on pastes containing mixed TFA and calcium hydroxide showed that this phase reacted with calcium hydroxide to form calcium aluminate hydrates. This formation of hydrates was accompanied by a hardening of the pastes. These results are very encouraging for the reuse of such TFA in cement-based materials because they can be considered as pozzolanic additions and could advantageously replace a part of the cement in cement-based materials. Finally, leaching tests were carried out to evaluate the environmental impact of the two TFAs. The elements which were less efficiently stabilized by process A were zinc, cadmium and antimony but, when the results of the leaching tests were compared with the thresholds of the European landfill directive, TFA-A could nevertheless be accepted at

Supporting School Leaders in Blended Learning with Blended Learning

Science.gov (United States)

Acree, Lauren; Gibson, Theresa; Mangum, Nancy; Wolf, Mary Ann; Kellogg, Shaun; Branon, Suzanne

2017-01-01

This study provides a mixed-methods case-study design evaluation of the Leadership in Blended Learning (LBL) program. The LBL program uses blended approaches, including face-to-face and online, to prepare school leaders to implement blended learning initiatives in their schools. This evaluation found that the program designers effectively…

Blended Learning

OpenAIRE

Bauerová, Andrea

2013-01-01

This thesis is focused on a new approach of education called blended learning. The history and developement of Blended Learning is described in the first part. Then the methods and tools of Blended Learning are evaluated and compared to the traditional methods of education. At the final part an efficient developement of the educational programs is emphasized.

Characterization of electron beam irradiated collagen-polyvinylpyrrolidone (PVP) and collagen-dextran (DEX) blends

International Nuclear Information System (INIS)

Dumitrascu, M.; Sima, E.; Minea, R.; Vancea, C.; Meltze, V.; Albu, M.G.

2011-01-01

Complete text of publication follows. The aim of the present study was to investigate the influence of electron beam irradiation on some blends of collagen-polyvinylpyrrolidone (PVP) and collagen-dextran (DEX). The blends were prepared by mixing different quantities of collagen, PVP and DEX in distilled water. After irradiation the obtained hydrogels were processed by controlled drying and freeze-drying. Both types of materials were characterized by FT-IR, FT-Raman, TG, DSC, water uptake and SEM. The intensity of the characteristic bands, in the range 2800-3600 cm -1 from FT-IR spectra, varied considerably as function of absorbed radiation dose. Raman spectra revealed the absence of the characteristic peak at 2700 cm -1 for irradiated blends at 30 kGy. Kinetic parameters were calculated from the TG, DTG and DSC data by means of isoconversion methods at different heating rates. Thereby a relation between absorbed radiation dose and activation energy was established. Water uptake studies were carried out in PBS solution (phosphate buffer saline) at 37 deg C and pH = 7.4 and the results revealed a decrease of the water uptake with increasing of absorbed radiation dose.

Sodium leak detection on large pipes. Heat insulating shells made of silico-aluminate

International Nuclear Information System (INIS)

Antonakas, D.; Blanc, R.; Casselman, C.; Malet, J.C.

1986-05-01

This report presents an equipment installed on the large secondary pipes of fast reactors, ensuring several functions: support and equilibrium of static and dynamic loads, heat insulator, preheating, and the detection of possible sodium leaks. The research programs associated to the development of the shells are briefly evoked; then, the report deals no longer with the studies on silico-aluminate aging and the detection performance [fr

Lithium aluminates and tritium production; Aluminatos de litio y produccion de tritio

Energy Technology Data Exchange (ETDEWEB)

Carrera G, L.M.; Palacios G, O.; Bosch G, P. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1997-07-01

In this work it is studied the crystalline structure of lithium aluminates prepared by three different methods, namely: solid state reaction, humid reaction and sol-gel reaction. The analysis methods are the X-ray diffractometry and the scanning and transmission electron microscopy. This study is realized as in original materials as in irradiated materials at the TRIGA Mark reactor, to correlate the synthesis method with response of these materials to the mixed irradiation of nuclear reactor. (Author)

Relations between blended learning possibilities and teachers' approaches to blended learning

DEFF Research Database (Denmark)

Stenalt, Maria Hvid; Nielsen, Tobias Alsted; Bager-Elsborg, Anna

Higher Education has embraced blended learning as a way of enhancing quality in teaching and helping students to learn. This presentation addresses relations between blended learning possiblities presented to teachers in a teacher training project and teachers’ approaches to blended learning. We...... suggest that in order to identify the level of impact of integrating technologies in teaching and learning, we need to understand the factors influencing approaches to design of courses for blended contexts. Participants in the teacher training project come from the Department of Law at Aarhus University......: • Optain locally-embedded knowledge about blended learning • Develop opportunities for law students to receive (more) feedback • Comply with strategic aims The results so far suggest that teachers provide a disciplinary perspective on the key dimensions of blended learning, which influences...

Phase transformations in lithium aluminates irradiated with neutrons; Transformaciones de fase en aluminatos de litio irradiados con neutrones

Energy Technology Data Exchange (ETDEWEB)

Carrera, L.M.; Delfin L, A.; Urena N, F.; Basurto, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Bosch, P. [UAM-I, 09340 Mexico D.F. (Mexico)

2003-07-01

The lithium aluminate like candidate to be used in the coverings producers of tritium in the fusion nuclear reactors, presents high resistance to the corrosion to the one to be stuck to structural materials as special steels. However, the crystallographic changes that take place in the cover that is continually subjected to irradiation with neutrons, can alter its resistance to the corrosion. In this work the changes of crystalline structure are shown that they present two types of nano structures of lithium aluminates, subjected to an average total dose 7.81 x 10{sup 8} Gy in the fixed irradiation system of capsules of the one TRIGA Mark lll nuclear reactor of the Nuclear Center of Mexico. The studied nano structures presented only phase transformations without formation of amorphous material. (Author)

The influence of alloying elements on the hot-dip aluminizing process and on the subsequent high-temperature oxidation

International Nuclear Information System (INIS)

Glasbrenner, H.; Nold, E.; Voss, Z.

1997-01-01

For hot dip aluminizing HDA an Al melt was doped with one of the elements Mo, W or Nb with a nominal composition of about 1 wt%. In case of W, the nominal composition was achieved, not so for Mo and Nb. The influence of these elements on the coating formed and on the following oxidation process was investigated. Hot dip aluminizing was carried out at 800 C for 5 min under dry Ar atmosphere. The oxidation experiments were performed at 950 C for 24 h in air. Compared to the HDA processes with pure Al, the addition of the alloying elements lead to thinner intermetallic layers. A change in the oxidation behavior was observed as well concerning the suppression of internal oxidation and the formation of dense and close oxide scales. (orig.)

Effect of Ethyl Ester L-Lysine Triisocyanate addition to produce reactive PLA/PCL bio-polyester blends for biomedical applications.

Science.gov (United States)

Visco, Annamaria; Nocita, Davide; Giamporcaro, Alberto; Ronca, Sara; Forte, Giuseppe; Pistone, Alessandro; Espro, Claudia

2017-04-01

We report in this paper the effects of Ethyl Ester L-Lysine Triisocyanate (LTI) on the physical-mechanical properties of Poly(lactide)/Poly(ε-caprolactone) (PLA/PCL) polyesters blends. The PLA/PCL ratios considered were 20/80, 50/50 and 80/20 (wt/wt %) and LTI was added in amounts of 0.0-0.5-1.0 phr. PLA and PCL reacted with LTI during processing in a Brabender twin screw internal mixer to produce block copolymers in-situ. The resulting blends have been characterized by torque measurements, uniaxial tensile tests, Differential Scanning Calorimeter, contact angle measurements with a Phosphate Buffered Saline (PBS) solution, ATR analysis and morphological SEM observations. Experimental results highlighted how LTI enhanced interaction and dispersion of the two components, resulting into a synergic effect in mechanical properties. Mechanical and physical properties can be tailored by changing the blend composition. The most noticeable trend was an increase in ductility of the mixed polymers. Besides, LTI decreased blend's wet ability in PBS and lowered the starting of crystalline phase formation for both polymers, confirming an interaction among them. These reactive blends could find use as biomedical materials, e.g. absorbable suture threads or scaffolds for cellular growth. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of aluminizing of Cr-containing ferritic alloys on the seal strength of a novel high-temperature solid oxide fuel cell sealing glass

Science.gov (United States)

Chou, Yeong-Shyung; Stevenson, Jeffry W.; Singh, Prabhakar

A novel high-temperature alkaline earth silicate sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was used to join two metallic coupons of Cr-containing ferritic stainless steel for seal strength evaluation. In previous work, SrCrO 4 was found to form along the glass/steel interface, which led to severe strength degradation. In the present study, aluminization of the steel surface was investigated as a remedy to minimize or prevent the strontium chromate formation. Three different processes for aluminization were evaluated with Crofer22APU stainless steel: pack cementation, vapor-phase deposition, and aerosol spraying. It was found that pack cementation resulted in a rough surface with occasional cracks in the Al-diffused region. Vapor-phase deposition yielded a smoother surface, but the resulting high Al content increased the coefficient of thermal expansion (CTE), resulting in the failure of joined coupons. Aerosol spraying of an Al-containing salt resulted in the formation of a thin aluminum oxide layer without any surface damage. The room temperature seal strength was evaluated in the as-fired state and in environmentally aged conditions. In contrast to earlier results with uncoated Crofer22APU, the aluminized samples showed no strength degradation even for samples aged in air. Interfacial and chemical compatibility was also investigated. The results showed aluminization to be a viable candidate approach to minimize undesirable chromate formation between alkaline earth silicate sealing glass and Cr-containing interconnect alloys for SOFC applications.

Blended Learning

NARCIS (Netherlands)

Van der Baaren, John

2009-01-01

Van der Baaren, J. (2009). Blended Learning. Presentation given at the Mini symposium 'Blended Learning the way to go?'. November, 5, 2009, The Hague, The Netherlands: Netherlands Defence Academy (NDLA).

Irradiation damage in gamma lithium aluminate - LiAlO2

International Nuclear Information System (INIS)

Auvray-Gely, M.H.

1989-01-01

Single crystals of gamma lithium aluminate (of tetragonal structure) are irradiated) with various projectiles (electrons, He ions, protons, X and gamma photons) and we used (i) electronic paramagnetic resonance (EPR) and optical absorption to detect the defects produced, and (ii) transmission electron microscopy (TEM). The lithium aluminate single crystals irradiated with electrons or ions contain five different paramagnetic defects. Each of them has several anisotropic configurations whose EPR signals (i) have a Lande factor close to 2, (ii) exhibit a resolved hyperfine structure and (iii) are identical only when the static magnetic field is along /001/. In addition, four optical absorption bands appear in the range 1-6 eV in the same irradiation conditions. But only three among the five paramagnetic defects and one of the optical bands appear in X-and gamma-ray irradiated samples. Using these observations, we discuss the nature of the detected defects and we conclude about the type of their production mechanism. Particularly, we assign a six-line EPR signal and an optical band in the ultraviolet range to the F + -centre. We compare this hypothesis to a defect model based on the computation of approximate electronic wave functions using the variational method. Our TEM study shows that when gamma-LiAlO 2 single crystals are irradiated with 1 MeV electrons (fluence: 10 20 electrons/sqcm), tridimensional defects (of mean dimension 100 nm) appear. At lower energies, the defect production is hidden by a thermal effect that is sufficient to induce the evaporation of lithium oxyde and the formation of LiAl 5 0 8 [fr

Room temperature synthesis of glycerol carbonate catalyzed by spray dried sodium aluminate microspheres

OpenAIRE

Sreerangappa, Ramesh; Debecker, Damien P.; 13th European Congress on Catalysis – EuropaCat 2017

2017-01-01

Nanostructured NaAlO2 microspheres are produced by one-pot spray dried route, and are characterized by various physico-chemical methods. The obtained solids are composed of spherical aggregates of sodium aluminate with small crystallite size and strong surface basicity. This makes them highly active catalysts in the base-catalyzed synthesis of glycerol carbonate from glycerol and dimethyl carbonate. The catalyst does not leach and showed good reusability up to three cycles.

Facile Fabrication of a Hierarchical Superhydrophobic Coating with Aluminate Coupling Agent Modified Kaolin

OpenAIRE

Hui Li; Mengnan Qu; Zhe Sun; Jinmei He; Anning Zhou

2013-01-01

A superhydrophobic coating was fabricated from the dispersion of unmodified kaolin particles and aluminate coupling agent in anhydrous ethanol. Through surface modification, water contact angle of the coating prepared by modified kaolin particles increased dramatically from 0° to 152°, and the sliding angle decreased from 90° to 3°. Scanning electron microscopy was used to examine the surface morphology. A structure composed of micro-nano hierarchical component, combined with the surface modi...

Polymer blends

Energy Technology Data Exchange (ETDEWEB)

Allen, Scott D.; Naik, Sanjeev

2017-08-22

The present invention provides, among other things, extruded blends of aliphatic polycarbonates and polyolefins. In one aspect, provided blends comprise aliphatic polycarbonates such as poly(propylene carbonate) and a lesser amount of a crystalline or semicrystalline polymer. In certain embodiments, provided blends are characterized in that they exhibit unexpected improvements in their elongation properties. In another aspect, the invention provides methods of making such materials and applications of the materials in applications such as the manufacture of consumer packaging materials.

Blended learning

DEFF Research Database (Denmark)

Staugaard, Hans Jørgen

2012-01-01

Forsøg på at indkredse begrebet blended learning i forbindelse med forberedelsen af projekt FlexVid.......Forsøg på at indkredse begrebet blended learning i forbindelse med forberedelsen af projekt FlexVid....

Practical Implications from Observed Lead Pipe Scale Mineralogy in a Blended Phosphate Treated System - slides

Science.gov (United States)

Many water utilities in the United States rely on the addition of phosphate-based corrosion inhibitors to optimize their corrosion control and comply with requirements of the Lead and Copper Rule. Orthophosphate is used on the theory of forming low solubility Pb(II)-orthophosphat...

Method of growing yttrium aluminate and/or lanthanide single crystals with perovskite structure

International Nuclear Information System (INIS)

Kvapil, Jiri; Perner, B.; Kvapil, Josef; Blazek, K.

1989-01-01

Single crystals of yttrium aluminate and/or lanthanide with perovskite structure are grown from melt in a vacuum at a pressure of gas residues of max. 0.01 Pa. The melt contains 1±0.05 gram-ions of aluminium per gram-ion of yttrium and/or lanthanides. The single crystals are then heated in a vacuum (0.01 Pa) at temperatures of 1,450 to 1,800 degC for 2 to 3 hours. (B.S.)

The Effect of (Ag, Ni, Zn)-Addition on the Thermoelectric Properties of Copper Aluminate

DEFF Research Database (Denmark)

Yanagiya, Shun-ichi; Van Nong, Ngo; Xu, Jianxiao Jackie

2010-01-01

Polycrystalline bulk copper aluminate Cu1-x-yAgxByAlO2 with B = Ni or Zn were prepared by spark plasma sintering and subsequent thermal treatment. The influence of partial substitution of Ag, Ni and Zn for Cu-sites in CuAlO2 on the high temperature thermoelectric properties has been studied......, indicating a significant improvement compared with the non-doped CuAlO2 sample...

Nickel stabilization efficiency of aluminate and ferrite spinels and their leaching behavior.

Science.gov (United States)

Shih, Kaimin; White, Tim; Leckie, James O

2006-09-01

Stabilization efficiencies of spinel-based construction ceramics incorporating simulated nickel-laden waste sludge were evaluated and the leaching behavior of products investigated. To simulate the process of immobilization, nickel oxide was mixed alternatively with gamma-alumina, kaolinite, and hematite. These tailoring precursors are commonly used to prepare construction ceramics in the building industry. After sintering from 600 to 1480 degrees C at 3 h, the nickel aluminate spinel (NiAl204) and the nickel ferrite spinel (NiFe204) crystallized with the ferrite spinel formation commencing about 200-300 degrees C lower than for the aluminate spinel. All the precursors showed high nickel incorporation efficiencies when sintered at temperatures greater than 1250 degrees C. Prolonged leach tests (up to 26 days) of product phases were carried out using a pH 2.9 acetic acid solution, and the spinel products were invariably superior to nickel oxide for immobilization over longer leaching periods. The leaching behavior of NiAl2O4 was consistent with congruent dissolution without significant reprecipitation, but for NiFe2O4, ferric hydroxide precipitation was evident. The major leaching reaction of sintered kaolinite-based products was the dissolution of cristobalite rather than NiAl2O4. This study demonstrated the feasibility of transforming nickel-laden sludge into spinel phases with the use of readily available and inexpensive ceramic raw materials, and the successful reduction of metal mobility under acidic environments.

Synthesis and test of sorbents based on calcium aluminates for SE-SR

International Nuclear Information System (INIS)

Barelli, L.; Bidini, G.; Di Michele, A.; Gallorini, F.; Petrillo, C.; Sacchetti, F.

2014-01-01

Highlights: • Synthesis strategy of CaO incorporation into calcium aluminates was approached. • Three innovative sorbents (M1, M2, M3) were synthesized and characterized. • Sorption capacity of developed sorbents was evaluated in multi-cycle processes. • M3 sorbent showed best performance, much higher than conventional CaO ones. • M3 sorbent functionality in SE-SR process was verified. - Abstract: Greenhouse gases emission of power generation plants will be continuously tightened to achieve European targets in terms of CO 2 emissions. In particular, the switching to a sustainable power generation using fossil fuels will be strongly encouraged in the future. In this context, sorption-enhanced steam reforming (SE-SR) is a promising process because it can be implemented as a CCS pre-combustion methodology. The purpose of this study is to develop and test innovative materials in order to overcome main limitations of standard CaO sorbent, usually used in the SE-SR process. The investigated innovative sorbents are based on incorporation of CaO particles into inert materials which significantly reduce the performance degradation. In particular, sorbent materials based on calcium aluminates were considered, investigating different techniques of synthesis. All synthesized materials were packed, together with the catalyst, in a fixed bed reactor and tested in sorption/regeneration cycles. Significant improvements were obtained respect to standard CaO regarding sorption capacity stability exhibited by the sorbent

Polystyrene/Hyperbranched Polyester Blends and Reactive Polystyrene/Hyperbranched Polyester Blends

National Research Council Canada - National Science Library

Mulkern, Thomas

1999-01-01

.... In this work, the incorporation of HBPs in thermoplastic blends was investigated. Several volume fractions of hydroxyl functionalized hyperbranched polyesters were melt blended with nonreactive polystyrene (PS...

Contribution to the study of porous or very finely divided alumina; Contribution a l'etude des alumines poreuses ou tres finement divisees

Energy Technology Data Exchange (ETDEWEB)

Juillet, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-12-15

An amorphous porous alumina having a large surface area can be made non-stoichiometric by a treatment at 500 - 700 deg C in a vacuum. The oxygen deficit after a treatment at 500 deg C, and the aluminium deficit after a treatment at 700 deg C, give rise to semiconductor properties successively of type n and of the type p. A crystallized {delta}-alumina in the form of non-porous spherical grains compressed at a pressure of 1 to 5 metric tons/cm{sup 2} is also non-stoichiometric with a deficit of oxygen or of aluminium. None of these phenomena could be observed with a sample which had not been compressed. The favorable influence of oxygen on the recrystallization process of amorphous alumina, and on the {delta}-{alpha}, transformation of crystallized alumina has been demonstrated. Furthermore, the strains produced by the compression of the {delta}-alumina make possible its transformation in air into a at a temperature lower than the temperature necessary to observe this phenomenon with non-compressed {delta}-alumina. Amorphous alumina undergoes an intergranular sintering at 500 deg C and an intergranular sintering at 1 000 deg C. Only the latter occurs in the case of spherical alumina grains. For these, the strains brought about by the compression cause a lowering of 100 deg C in the threshold sintering temperature, with respect to the temperature required to produce the phenomena in a non-compressed sample. The amount of sintering in a crystallized alumina pellet depends, as well, on the rate of rise of temperature. This study tends to show that new properties, or at least unusual solid-state properties, can be observed on disorganised solids or on solids which are crystallized but which have a large surface area and a certain amount of strain. (author) [French] Une alumine poreuse amorphe de grande surface specifique peut etre rendue non-stoechiometrique par traitement sous vide pousse a 500-700 deg C. Le deficit en oxygene apres chauffage a 500 deg C, puis le

A two-phase model for aluminized explosives on the ballistic and brisance performance

Science.gov (United States)

Kim, Wuhyun; Gwak, Min-cheol; Lee, Young-hun; Yoh, Jack J.

2018-02-01

The performance of aluminized high explosives is considered by varying the aluminum (Al) mass fraction in a heterogeneous mixture model. Since the time scales of the characteristic induction and combustion of high explosives and Al particles differ, the process of energy release behind the leading detonation wave front occurs over an extended period of time. For simulating the performance of aluminized explosives with varying Al mass fraction, HMX (1,3,5,7-tetrahexmine-1,3,5,7-tetrazocane) is considered as a base explosive when formulating the multiphase conservation laws of mass, momentum, and energy exchanges between the HMX product gases and Al particles. In the current study, a two-phase model is utilized in order to determine the effects of the Al mass fraction in a condensed phase explosive. First, two types of confined rate stick tests are considered to investigate the detonation velocity and the acceleration ability, which refers to the radial expansion velocity of the confinement shell. The simulation results of the confined rate stick test are compared with the experimental data for the Al mass fraction range of 0%-25%, and the optimal Al mass fraction is provided, which is consistent with the experimental observations. Additionally, a series of plate dent test simulations are conducted, the results of which show the same tendency as those of the experimental tests with varying Al mass fractions.

Dynamic Mechanical Properties and Constitutive Relation of an Aluminized Polymer Bonded Explosive at Low Temperatures

Directory of Open Access Journals (Sweden)

Yuliang Lin

2014-01-01

Full Text Available Polymer bonded explosives (PBXs are widely used as energetic fillings in various warheads, which maybe are utilized under extreme environments, such as low or high temperatures. In this paper, the dynamic response of an aluminized polymer bonded explosive was tested at a range of temperatures from −55°C to −2°C and a fixed loading strain rate (~700 s−1 with the split Hopkinson pressure bar (SHPB. The PBX tested is aluminized, which contains 76 wt% RDX, 20 wt% aluminum powder, and 4 wt% polymer binder, respectively. The results show that the effect of temperature on the strength of the PBX is obvious at the tested strain rates. Based on the experimental results and prophase studies, a constitutive model was obtained, in which the effect of temperature and strain rate were considered. The modeling curves fit well with the experimental results, not only at low temperature under 0°C, but also at room temperature (20°C. The model may be used to predict the dynamic performances of the PBXs in various environments.

Room temperature synthesis of glycerol carbonate catalyzed by spray dried sodium aluminate microspheres

OpenAIRE

Sreerangappa, Ramesh; Debecker, Damien P.

2017-01-01

Nanostructured NaAlO2 microspheres are produced from an aqueous solution, by a one-pot spray drying route. The obtained solids are composed of spherical aggregates of sodium aluminate with small crystallite size and strong surface basicity. This makes them highly active catalysts in the base-catalyzed synthesis of glycerol carbonate from glycerol and dimethyl carbonate. The new catalyst does not leach and is recyclable. NaAlO2 microspheres outcompete commercially available NaAlO2 as well as o...

Profiling Student Behaviour in a Blended Course: Closing the Gap Between Blended Teaching and Blended Learning

NARCIS (Netherlands)

Bos, Nynke; Brand-Gruwel, Saskia

2018-01-01

Blended learning is often associated with student-oriented learning in which students have varying degrees of control over their learning process. However, the current notion of blended learning is often a teacher- oriented approach in which the teacher identifies the used learning technologies and

Analysis of phosphate esters in plant material. Extraction and purification.

Science.gov (United States)

Isherwood, F A; Barrett, F C

1967-09-01

1. A critical study was made of the quantitative extraction of nucleotide and sugar phosphates from plant tissue by either boiling aqueous ethanol or cold trichloroacetic acid. The effect of the extraction technique on the inactivation of the enzymes in the plant tissue and the possibility of adsorption of the phosphate esters on the cell wall were especially considered. 2. In the recommended method the plant tissue was frozen in liquid nitrogen, ground to a powder and then blended with cold aqueous trichloroacetic acid containing 8-hydroxyquinoline to prevent adsorption. 3. The extract contained large amounts of trichloroacetic acid, cations, chloride, sugars, amino acids, hydroxy organic acids, phytic acid, orthophosphoric acid and high-molecular-weight material including some phosphorus-containing compounds. All of these were removed as they were liable to interfere with the chromatographic or enzymic assay of the individual nucleotide or sugar phosphates. 4. The procedure was as follows: the last traces of trichloroacetic acid were extracted with ether after the solution had been passed through a column of Dowex AG 50 in the hydrogen form to remove all cations. High-molecular-weight compounds were removed by ultrafiltration and low-molecular-weight solutes by a two-stage chromatography on cellulose columns with organic solvents. In the first stage, sugars, amino acids, chloride and phytic acid were separated by using a basic solvent (propan-1-ol-water-aqueous ammonia) and, in the second stage, the organic acids and orthophosphoric acid were separated by using an acidic solvent (di-isopropyl ether-formic acid-2-methylpropan-2-ol-water). The final solution of nucleotide and sugar phosphates was substantially free from other solutes and was suitable for the detection of individual phosphate esters by either chromatography or enzymic assay. 5. The recovery of d-glucose 6-phosphate or adenosine 5'-triphosphate added to a trichloroacetic acid extract simulating that

Effect of blending temperature on the mechanical properties of PVC/ENR blend upon irradiation

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

2000-01-01

Poly (vinyl chloride) / epoxidized natural rubber blends were prepared with a Brabender plasticorder at 140, 150, 160, 170 and 180 degree C mixing temperatures. They were mixed at 50 rpm rotor speed for 10 min. The blends were irradiated with doses ranging from 0-200 kGy. Changes in tensile strength, modulus at 100% elongation, gel fraction and damping properties (tan δ) of the blends with increasing mixing temperatures and irradiation doses were investigated. In general, it was observed that the mixing temperature is important in maximizing the positive effect of irradiation. Results revealed that a readily miscible blend enjoy maximum benefit from irradiation meanwhile irradiation impart miscibility to a partially miscible PVC/ENR blend. The enhancement in blend properties is believed to be attributed by the irradiation-induced crosslinking along with irradiation-induced interaction between the polymers. The radiation-induced degradation found to be prominent at higher doses for blend that has undergone excessive thermal degradation. However evidence did not reveal the specific nature of radiation-induced reaction responsible for the improved interactions of the blends. (author)

Blending Words Found In Social Media

Directory of Open Access Journals (Sweden)

Giyatmi Giyatmi

2017-12-01

Full Text Available There are many new words from the social media such as Netizen, Trentop, and Delcon. Those words include in blending. Blending is one of word formations combining two clipped words to form a brand new word. The researchers are interested in analyzing blend words used in the social media such as Instagram, Twitter, Facebook, and Blackberry Messenger. This research aims at (1 finding blend words used in the social media (2 describing kinds of blend words used in social media (3 describing the process of blend word formation used in the social media. This research uses some theories dealing with definition of blending and kinds of blending. This research belongs to descriptive qualitative research. Data of the research are English blend words used in social media. Data sources of this research are websites consisting of some English words used in social media and some social media users as the informant. Techniques of data collecting in this research are observation and simak catat. Observation is by observing some websites consisting of some English words used in social media. Simak catat is done by taking some notes on the data and encoding in symbols such as No/Blend words/Kinds of Blending. The researchers use source triangulation to check the data from the researchers with the informant and theory triangulation to determine kinds of blending and blend word formation in social media. There are115 data of blend words. Those data consists of 65 data of Instagram, 47 data of Twitter, 1 datum of Facebook, and 2 data of Blackberry Messenger. There are 2 types of blending used in social media;108 data of blending with clipping and 7 data of blending with overlapping. There are 10 ways of blend word formation found in this research.

Design Principles for the Blend in Blended Learning: A Collective Case Study

Science.gov (United States)

Lai, Ming; Lam, Kwok Man; Lim, Cher Ping

2016-01-01

This paper reports on a collective case study of three blended courses taught by different instructors in a higher education institution, with the purpose of identifying the different types of blend and how the blend supports student learning. Based on the instructors' and students' interviews, and document analysis of course outlines, two major…

Preparation and characterization of perovskite structure lanthanum gallate and lanthanum aluminate based oxides

OpenAIRE

Li, Shuai

2009-01-01

The present work was initiated to study the synthesis and properties of lanthanum gallate based oxides as intermediate temperature electrolyte for solid oxide fuel cells. The wet chemical method, polymer complexing route, was used to prepare the precursor powders. To further investigate the polymer complexing method, it was also applied to the preparation of lanthanum aluminate based oxides.   Single perovskite phase La0.8Sr0.2Ga0.83Mg0.17O2.815 can be prepared by the polymer complexing meth...

Halting of the calcium aluminate cement hydration process

International Nuclear Information System (INIS)

Luz, A.P.; Borba, N.Z; Pandolfelli, V.C.

2011-01-01

The calcium aluminate cement reactions with water lead to the anhydrous phases dissolution resulting a saturated solution, followed by nucleation and crystal growth of the hydrate compounds. This is a dynamic process, therefore, it is necessary to use suitable methods to halt the hydration in order to study the phase transformations kinetics of such materials. In this work two methods are evaluated: use of acetone and microwave drying, aiming to withdraw the free water and inhibit further reactions. X ray diffraction and thermogravimetric tests were used to quantify the phases generated in the cement samples which were kept at 37 deg C for 1 to 15 days. The advantages and disadvantages of those procedures are presented and discussed. The use of microwave to halt the hydration process seems to be effective to withdraw the cement free water, and it can further be used in researches of the refractory castables area, endodontic cements, etc. (author)

Performance of phosphogypsum and calcium magnesium phosphate fertilizer for nitrogen conservation in pig manure composting.

Science.gov (United States)

Li, Yun; Luo, Wenhai; Li, Guoxue; Wang, Kun; Gong, Xiaoyan

2018-02-01

This study investigated the performance of phosphogypsum and calcium magnesium phosphate fertilizer for nitrogen conservation during pig manure composting with cornstalk as the bulking agent. Results show that phosphogypsum increased nitrous oxide (N 2 O) emission, but significantly reduced ammonia (NH 3 ) emission and thus enhanced the mineral and total nitrogen (TN) contents in compost. Although N 2 O emission could be reduced by adding calcium magnesium phosphate fertilizer, NH 3 emission was considerably increased, resulting in an increase in TN loss during composting. By blending these two additives, both NH 3 and N 2 O emissions could be mitigated, achieving effective nitrogen conservation in composting. More importantly, with the addition of 20% TN of the mixed composting materials, these two additives could synergistically improve the compost maturity and quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

Blended acquisition with dispersed source arrays

NARCIS (Netherlands)

Berkhout, A.J.

2012-01-01

Blended source arrays are historically configured with equal source units, such as broadband vibrators (land) and broadband air-gun arrays (marine). I refer to this concept as homogeneous blending. I have proposed to extend the blending concept to inhomogeneous blending, meaning that a blended

Creep-rupture Behaviors of a Diffusionally Aluminized Alloy 617

Energy Technology Data Exchange (ETDEWEB)

Sah, Injin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Sung Hwan; Jang, Chang Heui [KAIST, Daejeon (Korea, Republic of)

2015-05-15

In light of the surface reaction, a sufficient Cr content in the matrix leads to an external chromia (Cr{sub 2}O{sub 3}) layer on the surface with the occurrence of internal oxides (Al{sub 2}O{sub 3}) into the matrix. It is well known that the internal oxides will reduce the effective cross-sectional area and/or be a notch under the loading condition. Thus, there have been extensive efforts to improve the oxidation resistance by imposing an aluminized layer (βNiAl or γ-Ni{sub 3}Al) for Ni-Cr alloys. In particular, the extensively formed carbide free zone below the affected substrate will reduce the creep-rupture strengths because the inter-granular carbides present along the grain boundaries effectively impede the grain boundary sliding under high-temperature tensile loading conditions.

Hydration of Portland cement with additions of calcium sulfoaluminates

International Nuclear Information System (INIS)

Le Saoût, Gwenn; Lothenbach, Barbara; Hori, Akihiro; Higuchi, Takayuki; Winnefeld, Frank

2013-01-01

The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C–S–H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA–OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

The crack propagating behavior of composite coatings prepared by PEO on aluminized steel during in situ tensile processing

International Nuclear Information System (INIS)

Chen Zhitong; Li Guang; Wu Zhenqiang; Xia Yuan

2011-01-01

Research highlights: → Composite coatings on the aluminized steel were prepared by the plasma electrolytic oxidation (PEO) technique, which comprised of Fe-Al layer, Al layer and Al 2 O 3 layer. → The evaluation method of the crack critical opening displacement δ c was introduced to describe quantitatively the resistance of Al layer to the propagation behavior of cracks and evaluate the fracture behavior of composite coatings. → The crack propagating model was established. - Abstract: This paper investigates the in situ tensile cracks propagating behavior of composite coatings on the aluminized steel generated using the plasma electrolytic oxidation (PEO) technique. Cross-sectional micrographs and elemental compositions were investigated by scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS). The composite coatings were shown to consist of Fe-Al, Al and Al 2 O 3 layers. The cracks propagating behavior was observed in real-time in situ SEM tensile test. In tensile process, the cracks were temporarily stopped when cracks propagated from Fe-Al layer to Al layer. The critical crack opening displacement δ c was introduced to quantitatively describe the resistance of the Al layer. There was a functional relation among the thickness ratio t Al /t Al 2 O 3 , the δ c of composite coatings and tensile cracks' spacing. The δ c increased with the increasing of the thickness ratio (t Al /t Al 2 O 3 ). The high δ c value means high fracture resistance. Therefore, a control of the thickness ratio t Al /t Al 2 O 3 was concerned as a key to improve the toughness and strength of the aluminized steel.

Blended Learning

Science.gov (United States)

Imbriale, Ryan

2013-01-01

Teachers always have been and always will be the essential element in the classroom. They can create magic inside four walls, but they have never been able to create learning environments outside the classroom like they can today, thanks to blended learning. Blended learning allows students and teachers to break free of the isolation of the…

Apparatus for blending small particles

International Nuclear Information System (INIS)

Bradley, R.A.; Reese, C.R.; Sease, J.D.

1975-01-01

An apparatus is described for blending small particles and uniformly loading the blended particles in a receptacle. Measured volumes of various particles are simultaneously fed into a funnel to accomplish radial blending and then directed onto the apex of a conical splitter which collects the blended particles in a multiplicity of equal subvolumes. Thereafter the apparatus sequentially discharges the subvolumes for loading in a receptacle. A system for blending nuclear fuel particles and loading them into fuel rod molds is described in a preferred embodiment

Structural and luminescence effects of Ga co-doping on Ce-doped yttrium aluminate based phosphors

Energy Technology Data Exchange (ETDEWEB)

Ayvacikli, M. [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Canimoglu, A. [Nigde University, Faculty of Arts and Sciences, Physics Department, Nigde (Turkey); Muresan, L.E., E-mail: laura_muresan2003@yahoo.com [Babes Bolyai University, Raluca Ripan Institute for Research in Chemistry, Fantanele 30, 400294 Cluj-Napoca (Romania); Barbu Tudoran, L. [Babes Bolyai University, Electronic Microscopy Centre, Clinicilor 37, 400006 Cluj Napoca (Romania); Garcia Guinea, J. [Museo Nacional Ciencias Naturales, Jose Gutierrez Abascal 2, Madrid 28006 (Spain); Karabulut, Y. [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Jorge, A. [Museo Nacional Ciencias Naturales, Jose Gutierrez Abascal 2, Madrid 28006 (Spain); Karali, T. [Ege University, Institute of Nuclear Sciences, 35100 Bornova, İzmir (Turkey); Can, N., E-mail: cannurdogan@yahoo.com [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Jazan University, Physics Department, P.O. Box 114, 45142 Jazan (Saudi Arabia)

2016-05-05

Herein, we primarily focus on luminescence spectrum measurements of various types of green emitting yttrium aluminate phosphors modified with gallium (Y{sub 3}Al{sub 5-x}Ga{sub x}O{sub 12}) synthesised by solid state reaction. The luminescent emission of samples depends on sample temperature and excitation radiation such as incident X-ray, electron and laser beam. Here, we measured radioluminescence (RL), cathodoluminescence (CL), photoluminescence (PL) along with XRD in order to clarify relationship between lattice defects and the spectral luminescence emissions. The RL and CL spectra of YAG:Ce exhibit an emission band ranging from 300 to 450 nm related to Y{sub Al} antisite defects. The broad emission band of garnet phosphors is shifted from 526 nm to 498 nm with increasing of Ga{sup 3+} content, while full width at half maximum (FWHM) of the band tends to be greater than the width of unmodified YAG:Ce garnet. Deconvolution of the spectrum reveals that three emission bands centred at 139, 234 and 294 °C occur in aluminate host garnets. - Highlights: • We present preparation of YAG:Ce{sup 3+}, Ga{sup 3+} phosphors by a solid state reaction method. • The shape and size of phosphor particles were investigated. • The luminescence properties were studied by different excitation sources.

Nucleation during gibbsites precipitation with seeds from sodium aluminate solution processed under ultrasound

Institute of Scientific and Technical Information of China (English)

陈国辉; 陈启元; 尹周澜; 张斌

2004-01-01

The secondary nucleation during gibbsite precipitation with seeds from sodium aluminate solution processed by ultrasound was examined by particle size distribution(PSD) analyses. Experiments indicate that at low temperature(＜65 ℃ ) and with low frequency ultrasound, the precipitation efficiency and also the secondary nucleation can be improved. Solution processed by low frequency ultrasound has more nuclei than common liquor does at low temperature. At 55 ℃, precipitation efficiency can he improved by 5.31 %, and the effect promoted by low frequency ultrasound decreases with the increase of temperature.

Investigation of diesel-ethanol blended fuel properties with palm methyl ester as co-solvent and blends enhancer

Directory of Open Access Journals (Sweden)

Mat Taib Norhidayah

2017-01-01

Full Text Available Diesel engine is known as the most efficient engine with high efficiency and power but always reported as high fuel emission. Malaysia National Automotive Policy (NAP was targeting to improve competitive regional focusing on green technology development in reducing the emission of the engine. Therefore, ethanol was introduced to reduce the emission of the engine and while increasing its performance, Palm methyl ester was introduced as blend enhancer to improve engine performance and improve diesel-ethanol blends stability. This paper aimed to study the characteristics of the blends and to prove the ability of palm-methyl-ester as co-solvent in ethanol-diesel blends. Stability and thermophysical test were carried out for different fuel compositions. The stability of diesel-ethanol blended was proved to be improved with the addition of PME at the longer period and the stability of the blends changed depending on temperature and ethanol content. Density and viscosity of diesel-ethanol-PME blends also give higher result than diesel-ethanol blends and it's proved that PME is able to increase density and viscosity of blends. Besides, heating value of the blends also increases with the increasing PME in diesel-ethanol blends.

Radiation effect on PVC/ENR blends

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan

1997-01-01

The effect of irradiation on the physical properties of Polyvinyl Chloride / Epoxidised Natural Rubber Blends (PVC/ENR blends) were investigated. The enhancement in tensile strength, elongation at break, hardness and aging properties of the blends have confirmed the positive effect of irradiation on the blends. It is evident from gel fraction and infra red spectroscopic studies that the blends of PVC and ENR cross-linked upon irradiation. The results also revealed that at any blend composition, the enhancement in properties depend on irradiation dose which controls the degree of radiation induced cross-linking. In an attempt to maximize the constructive effect of irradiation, the influence of various additives such as stabilizers, radiation sensitizers, fillers and processing aids on the blend properties were studied. The changes in blend properties upon irradiation with the presents of above additives were also presented in this paper

Blending into the mix

Energy Technology Data Exchange (ETDEWEB)

Adams, R.G.; Gibb, W.H.; Majid, K.A. [Power Technology (United Kingdom)

1999-07-01

Successful coal blending requires finding a careful balance between fuel costs and plant performance. A recent study of a Malaysian power plant shows how the utility (Tenaga Nasional Berhad (TNB)) could reduce fuel costs while avoiding boiler operating problems normally associated with firing low-grade coals. TNB`s Kaper 2220 MW power station in Selangor needed an improved method of coal blending for two new 500 MW units and for two existing 300 MW units. UK`s Power Technology was commissioned to identify what coal blends the boiler could tolerate. A Coal Quality Impact Model (CQIM) analysis of the effect of different coals and coal blends on combustion performance and economics, and a performance analysis of coal yard handling facility was made to determine whether the accuracy of the required blend could be achieved (using a Coal Handling Simulation, CHAS, software package). The CQIM study showed that the proportion of cheaper coals could be increased from 20% to 50% provided each shipment was adequately sampled. The CHAS study showed that use of a flat back reclaimer or modifications to the dry coal stove would allow accurate blending. 5 figs., 1 tab.

Decentralized Blended Acquisition

NARCIS (Netherlands)

Berkhout, A.J.

2013-01-01

The concept of blending and deblending is reviewed, making use of traditional and dispersed source arrays. The network concept of distributed blended acquisition is introduced. A million-trace robot system is proposed, illustrating that decentralization may bring about a revolution in the way we

Blended Learning: enabling Higher Education Reform

Directory of Open Access Journals (Sweden)

Kathleen Matheos

2018-01-01

Full Text Available Blended learning research and practice have been areas of growth for two decades in Canada, with over 95% of Canadian higher education institutions involved in some form of blended learning. Despite strong evidence based research and practice blended learning, for the most part, has remained at sidelined in Canadian universities. The article argues the need for blended learning to situate itself within the timely and crucial Higher Education Reform (HER agenda. By aligning the affordances of blended learning with the components of HER, blended learning can clearly serve as an enabler for HER.

Microstructural and compositional change of NaOH-activated high calcium fly ash by incorporating Na-aluminate and co-existence of geopolymeric gel and C–S–H(I)

KAUST Repository

Oh, Jae Eun

2012-05-01

This study explores the reaction products of alkali-activated Class C fly ash-based aluminosilicate samples by means of high-resolution synchrotron X-ray diffraction (HSXRD), scanning electron microscope (SEM), and compressive strength tests to investigate how the readily available aluminum affects the reaction. Class C fly ash-based aluminosilicate raw materials were prepared by incorporating Na-aluminate into the original fly ashes, then alkali-activated by 10 M NaOH solution. Incorporating Na-aluminate reduced the compressive strength of samples, with the reduction magnitude relatively constant regardless of length of curing period. The HSXRD provides evidence of the co-existence of C-S-H with geopolymeric gels and strongly suggests that the C-S-H formed in the current system is C-S-H(I). The back-scattered electron images suggest that the C-S-H(I) phase exists as small grains in a finely intermixed form with geopolymeric gels. Despite providing extra source of aluminum, adding Na-aluminate to the mixes did not decrease the Si/Al ratio of the geopolymeric gel. © 2012 Elsevier Ltd.

Microstructural and compositional change of NaOH-activated high calcium fly ash by incorporating Na-aluminate and co-existence of geopolymeric gel and C–S–H(I)

KAUST Repository

Oh, Jae Eun; Moon, Juhyuk; Oh, Sang-Gyun; Clark, Simon M.; Monteiro, Paulo J.M.

2012-01-01

This study explores the reaction products of alkali-activated Class C fly ash-based aluminosilicate samples by means of high-resolution synchrotron X-ray diffraction (HSXRD), scanning electron microscope (SEM), and compressive strength tests to investigate how the readily available aluminum affects the reaction. Class C fly ash-based aluminosilicate raw materials were prepared by incorporating Na-aluminate into the original fly ashes, then alkali-activated by 10 M NaOH solution. Incorporating Na-aluminate reduced the compressive strength of samples, with the reduction magnitude relatively constant regardless of length of curing period. The HSXRD provides evidence of the co-existence of C-S-H with geopolymeric gels and strongly suggests that the C-S-H formed in the current system is C-S-H(I). The back-scattered electron images suggest that the C-S-H(I) phase exists as small grains in a finely intermixed form with geopolymeric gels. Despite providing extra source of aluminum, adding Na-aluminate to the mixes did not decrease the Si/Al ratio of the geopolymeric gel. © 2012 Elsevier Ltd.

Effects of radiation on lithium aluminate samples properties

Energy Technology Data Exchange (ETDEWEB)

Botter, F.; Lefevre, F.; Rasneur, B.; Trotabas, M.; Roth, E.

The irradiation behaviour of lithium aluminate, a candidate material for a fusion reactor blanket, has been investigated. About 130 samples of 7.5% WLi content el-LiAlO2 have been loaded in a 6 level device, and were irradiated for 25.7 FPD in the core of the Osiris reactor at Saclay at the end of 1984, within an experiment named ALICE 1. The properties of several textural groups have been examined before and after irradiation and the correlation of the results observed as a funcion of the irradiation conditions is given. No significant variation of the properties, as a whole, was shown at 400C under fluences of 4.7x10S n cm S fast neutrons (>1 MeV) and 1.48x10S n cm S thermal neutrons. At 600C, under the highest flux, weight losses less than 1%, and decreases of 2 to 8% of the sound velocity were measured. Generally, neither swelling nor breakage, except those due to combined mechanical and thermal shocks, were observed.

Calcium aluminates potential for endodontics and orthopedics applications

International Nuclear Information System (INIS)

Santos, G.L. dos; Andrade, T.L.; Oliveira, I.R.; Pandolfelli, V.C.

2011-01-01

The mostly used material in the areas of endodontics (MTA, mineral trioxide aggregate) and bone reconstruction (PMMA, polymethyl methacrylate) present some limiting properties requiring thus changes in their compositions as well as the development of alternative materials. In this context, a novel biomaterial-based calcium aluminate cement (CAC) has been studied in order to keep the positive properties and clinical applications of MTA and PMMA, overcoming some their disadvantages. Recent studies involving the use of CAC are based on commercial products consisting of a mixture of phases. Improvements can be attained by searching the synthesis routes of CAC aiming the proper balance between the phases and the control of impurities that may impair its performance in applications in the areas of health. By the optimization of the CAC phases production, this article aims to present their characterization based on hydration temperature; working time and setting time; pH, ions solubilization and dissolution in contact with water and different solutions of simulated body fluid. The results indicated the CA phase as the most suitable for application in the areas of health. (author)

Mutable Lewis and Bronsted Acidity of Aluminated SBA-15 as Revealed by NMR of Adsorbed Pyridine-(15)N

Czech Academy of Sciences Publication Activity Database

Gurinov, A. A.; Rozhkova, Yu. A.; Zukal, Arnošt; Čejka, Jiří; Shenderovich, I, G.

2011-01-01

Roč. 27, č. 19 (2011), s. 12115-12123 ISSN 0743-7463 R&D Projects: GA AV ČR KAN100400701; GA ČR GA203/08/0604 Institutional research plan: CEZ:AV0Z40400503 Keywords : 15N NMR * post-synthesis alumination * phase Beckmann rearrangement Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.186, year: 2011

Influence of silicon on hot-dip aluminizing process and subsequent oxidation for preparing hydrogen/tritium permeation barrier

Energy Technology Data Exchange (ETDEWEB)

Han, Shilei; Li, Hualing; Wang, Shumao; Jiang, Lijun; Liu, Xiaopeng [Energy Materials and Technology Research Institute, General Research Institute for Nonferrous Metals, Beijing 100088 (China)

2010-04-15

The development of the International Thermonuclear Experimental Reactor (ITER) requires the production of a material capable of acting as a hydrogen/tritium permeation barrier on low activation steel. It is well known that thin alumina layer can reduce the hydrogen permeation rate by several orders of magnitude. A technology is introduced here to form a ductile Fe/Al intermetallic layer on the steel with an alumina over-layer. This technology, consisting of two main steps, hot-dip aluminizing (HDA) and subsequent oxidation behavior, seems to be a promising coating method to fulfill the required goals. According to the experiments that have been done in pure Al, the coatings were inhomogeneous and too thick. Additionally, a large number of cracks and porous band could be observed. In order to solve these problems, the element silicon was added to the aluminum melt with a nominal composition. The influence of silicon on the aluminizing and following oxidation process was investigated. With the addition of silicon into the aluminum melt, the coating became thinner and more homogeneous. The effort of the silicon on the oxidation behavior was observed as well concerning the suppression of porous band and cracks. (author)

Characterization and quantitative determination of calcium aluminate clinker phases through reflected light microscopy

International Nuclear Information System (INIS)

Marciano Junior, E.; Cunha Munhoz, F.A. da; Splettstoser Junior, J.; Placido, W.F.

1989-01-01

The identification and quantitative determination of phases in calcium aluminate clinker is of great importance to the producer, as it enables a better understanding of the cement and concrete properties, specially those concerning setting time and compressive strenght. Polished sections of three electrofused clinkers, one experimental and two industrial, were used to select the most suitable etchings in order to identify by microscopy the main phases (Ca, CA 2 , C 2 AS, C 12 A 7 , α-Al 2 O 3 ). Quantitative phases determinations by reflected light microscopy showed good results when compared to X-ray diffractometry measurements [pt

Encapsulation of strontium aluminate phosphors to enhance water resistance and luminescence

International Nuclear Information System (INIS)

Zhu Yong; Zeng Jianghua; Li Wenyu; Xu Li; Guan Qiu; Liu Yingliang

2009-01-01

Strontium aluminate SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors are chemically unstable against water or even moisture. To enhance the water resistance of the phosphors, an encapsulation was performed by direct surface reactions with phosphoric acid (H 3 PO 4 ). The morphology, surface structure, surface element composition, water resistance, luminescence, and photoacoustic spectrum of the phosphors before and after encapsulation were discussed. Experimental results showed that phosphors were perfectly encapsulated by amorphous layers in nanoscale and crystalline layers in microscale under different conditions. The water resistance of phosphors was greatly enhanced by the two types of layer. More importantly, the amorphous layers enhanced the luminescence of phosphors markedly. The possible mechanism for the enhancements was also proposed.

Study on the bound water of several high specific surface-area oxides (beryllia, alumina, silica-alumina); Etude de l'eau de constitution de plusieurs oxydes a grande surface specifique (glucine, alumine, silice-alumine)

Energy Technology Data Exchange (ETDEWEB)

Rouquerol, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-11-01

This study is concerned with the bound water of several oxides (beryllia, alumina, silica-alumina) at different steps of their dehydration (heating temperatures between 150 and 1100 deg. C). The following techniques have been used simultaneously: Thermal analysis (a new method has been developed), nitrogen adsorption (study of the texture), Diborane hydrolysis (qualitative and quantitative analysis of surface water), Infra-red spectrography (in the absorption range of water), Nuclear magnetic resonance (in the resonance range of protons). Thanks to these different techniques, five kinds of bound water have been observed. Attention is called on the great influence of the thermal treatment conditions on the evolution of the products resulting from the decomposition of alumina {alpha}-trihydrate Al(OH){sub 3} and beryllium {alpha}-hydroxide, in the course of the dehydration. Moreover, the author emphasizes the peculiar properties of the two kinds of oxides (alumina and beryllia) prepared through a new method of treatment under low pressure and constant speed of decomposition. Such particular features concern mainly texture, bound water, and consequently, also catalytic activity. (author) [French] Ce travail porte sur l'eau de constitution de plusieurs oxydes (glucine, alumine, silice-alumine) aux differents degres de leur deshydratation (temperatures de traitement comprises entre 150 et 1100 deg. C). Cette etude met simultanement en oeuvre: l'analyse thermique (proposition d'une nouvelle methode), l'adsorption d'azote (etude de texture), l'hydrolyse du diborane (analyse qualitative et quantitative de l'eau de surface), la spectrographie infra-rouge (dans le domaine d'absorption de l'eau), la resonance magnetique nucleaire (dans le domaine de resonance des protons). A l'aide de ces differentes techniques, cinq formes d'eau de constitution ont ete observees. L'attention est attiree sur la tres grande influence des conditions de traitement thermique sur l'evolution des

7 CFR 989.16 - Blend.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Blend. 989.16 Section 989.16 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... CALIFORNIA Order Regulating Handling Definitions § 989.16 Blend. Blend means to mix or commingle raisins. ...

Effect of Blending on the Composition and Acceptability of Blends of ...

African Journals Online (AJOL)

However the blend was found deficient in lysine, leucine, iso-leucine and phenylalanine when compared with the FAO recommendations for infants. Increased levels of pigeon pea in the blend also resulted in significant increases in potassium, phosphorus, sodium, magnesium and calcium. Similarly, increased levels of ...

Micro-stress dominant displacive reconstructive transition in lithium aluminate

Energy Technology Data Exchange (ETDEWEB)

Hu, Qiwei; Yan, Xiaozhi; Zhang, Leilei; Peng, Fang [Institute of Atomic and Molecular Physics, Sichuan University, 610065 Chengdu (China); Lei, Li, E-mail: lei@scu.edu.cn; He, Duanwei [Institute of Atomic and Molecular Physics, Sichuan University, 610065 Chengdu (China); Key Laboratory of High Energy Density Physics and Technology of Ministry of Education, Sichuan University, 610065 Chengdu (China); Li, Xiaodong [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

2016-08-15

It is supposed that diffusive reconstructive transitions usually take place under hydrostatic pressure or low stresses, and displacive reconstructive phase transitions easily occur at nonhydrostatic pressure. Here, by in-situ high pressure synchrotron X-ray diffraction and single-crystal Raman scattering studies on lithium aluminate at room temperature, we show that the reconstructive transition mechanism is dependent on the internal microscopic stresses rather than the macroscopic stresses. In this case, even hydrostatic pressure can favor the displacive transition if the compressibility of crystal is anisotropic. During hydrostatic compression, γ-LiAlO{sub 2} transforms to δ-LiAlO{sub 2} at about 4 GPa, which is much lower than that in previous nonhydrostatic experiments (above 9 GPa). In the region where both phases coexist, there are enormous microscopic stresses stemming from the lattice mismatch, suggesting that this transition is displacive. Furthermore, the atomic picture is drawn with the help of the shear Raman modes.

Morphology stabilization of heterogeneous blends

International Nuclear Information System (INIS)

1980-01-01

A heterogeneous elastomer blend is described, consisting of at least two elastomer components which are cross-linkable by irradiation and having a stabilized morphology formed by subjecting the blend to high energy radiation to a point from below to slightly above the gel dose of the blend. (author)

Locally restricted blending of Blobtrees

NARCIS (Netherlands)

Groot, de Erwin; Wyvill, B.; Wetering, van de H.M.M.

2009-01-01

Blobtrees are volume representations particularly useful for models which require smooth blending. When blending is applied to two or more Blobtree models, extra volume will be created in between the two surfaces to form a smooth connection. Although it is easy to apply blending, it is hard to

Performance of Blended Learning in University Teaching:

Directory of Open Access Journals (Sweden)

Michael Reiss

2010-07-01

Full Text Available Blended learning as a combination of classroom teaching and e-learning has become a widely represented standard in employee and management development of companies. The exploratory survey “Blended Learning@University” conducted in 2008 investigated the integration of blended learning in higher education. The results of the survey show that the majority of participating academic teachers use blended learning in single courses, but not as a program of study and thus do not exploit the core performance potential of blended learning. According to the study, the main driver of blended learning performance is its embeddedness in higher education. Integrated blended programs of study deliver the best results. In blended learning, learning infrastructure (in terms of software, culture, skills, funding, content providing, etc. does not play the role of a performance driver but serves as an enabler for blended learning.

Study of damages by neutron irradiation in lithium aluminates; Estudio de danos por irradiacion neutronica en aluminatos de litio

Energy Technology Data Exchange (ETDEWEB)

Palacios G, O

1999-06-01

Lithium aluminates proposed to the production of tritium in fusion nuclear reactors, due to the thermal stability that they present as well as the behavior of the aluminium to the irradiation. As a neutron flux with profile ({approx_equal} 14 Mev) of a fusion reactor is not available. A irradiation experiment was designed in order to know the micro and nano structure damages produced by fast and thermal neutrons in two irradiation positions of the fusion nuclear reactor Triga Mark III: CT (Thermal Column) and SIFCA (System of Irradiation Fixed of Capsules). In this work samples of lithium aluminate were characterized by XRD (X-Ray Diffraction), TEM (Transmission Electron Microscopy) and SEM (Scanning Electron Microscopy). Two samples were prepared by two methods: a) coalition method and b) peroxide method. This characterization comprised original and irradiated samples. The irradiated sample amounted to 4 in total: one for each preparation method and one for each irradiation position. The object of this analysis was to correlate with the received neutron dose the damages suffered by the samples with the neutron irradiation during long periods (440 H), in their micro and nano structure aspects; in order to understand the changes as a function of the irradiation zone (with thermal and fast neutron flux) and the preparation methods of the samples and having as an antecedent the irradiation in SIFCA position by short times (2h). The obtained results are referred to the stability of {gamma} -aluminate phase, under given conditions of irradiation and defined nano structure arrangement. They also refer to the proposals of growth mechanism and nucleation of new phases. The error associated with the measurement of neutron dose is also discussed. (Author)

Study on the bound water of several high specific surface-area oxides (beryllia, alumina, silica-alumina); Etude de l'eau de constitution de plusieurs oxydes a grande surface specifique (glucine, alumine, silice-alumine)

Energy Technology Data Exchange (ETDEWEB)

Rouquerol, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-11-01

This study is concerned with the bound water of several oxides (beryllia, alumina, silica-alumina) at different steps of their dehydration (heating temperatures between 150 and 1100 deg. C). The following techniques have been used simultaneously: Thermal analysis (a new method has been developed), nitrogen adsorption (study of the texture), Diborane hydrolysis (qualitative and quantitative analysis of surface water), Infra-red spectrography (in the absorption range of water), Nuclear magnetic resonance (in the resonance range of protons). Thanks to these different techniques, five kinds of bound water have been observed. Attention is called on the great influence of the thermal treatment conditions on the evolution of the products resulting from the decomposition of alumina {alpha}-trihydrate Al(OH){sub 3} and beryllium {alpha}-hydroxide, in the course of the dehydration. Moreover, the author emphasizes the peculiar properties of the two kinds of oxides (alumina and beryllia) prepared through a new method of treatment under low pressure and constant speed of decomposition. Such particular features concern mainly texture, bound water, and consequently, also catalytic activity. (author) [French] Ce travail porte sur l'eau de constitution de plusieurs oxydes (glucine, alumine, silice-alumine) aux differents degres de leur deshydratation (temperatures de traitement comprises entre 150 et 1100 deg. C). Cette etude met simultanement en oeuvre: l'analyse thermique (proposition d'une nouvelle methode), l'adsorption d'azote (etude de texture), l'hydrolyse du diborane (analyse qualitative et quantitative de l'eau de surface), la spectrographie infra-rouge (dans le domaine d'absorption de l'eau), la resonance magnetique nucleaire (dans le domaine de resonance des protons). A l'aide de ces differentes techniques, cinq formes d'eau de constitution ont ete observees. L'attention est attiree sur la tres grande influence

Osteoconductive bio-based meshes based on Poly(hydroxybutyrate-co-hydroxyvalerate) and poly(butylene adipate-co-terephthalate) blends

International Nuclear Information System (INIS)

Nar, Mangesh; Staufenberg, Gerrit; Yang, Bing; Robertson, Lesli; Patel, Rinkesh H.; Varanasi, Venu G.; D'Souza, Nandika Anne

2014-01-01

Poly(butylene adipate-co-terephthalate) (PBAT) and Poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) are biopolymers that have the potential to be used in applications of bone healing. In this study, it is hypothesized that the polymer blend has the combined strength and osteoconductivity to support osteoblast collagen formation. PBAT (PBAT 100), and a blend with 20% PHBV (PBAT 80) were extruded in the form of fibers and then knitted in the form of mesh. These were tested in the warp as well as weft direction for the tensile properties; these showed that the weft direction had higher performance than the warp. The individual fibers were kept in phosphate buffered saline (PBS) over the period of 8 weeks and were tested for the storage and loss modulus using a dynamic mechanical analyser (DMA). The results indicated that mechanical relaxation strength showed a decrease and then an increase. In vitro osteoconductivity studies were done by using differentiating osteoblasts (MC3T3-E1 subclone 4 cells). Environmental Scanning Electron Microscopy (ESEM) showed that pre-soaking the samples in α-MEM for two weeks resulted in cell attachment and growth. X-ray diffraction (XRD) was used to determine the change in structure of polymers due to in vitro degradation for two weeks. Raman spectroscopy showed that all scaffolds supported the formation of a collagenous network over the scaffold surfaces. For a combination of knittable manufacturing, mechanical performance and osteoconductivity, blends offer an effective route. - Highlights: • PBAT and PHBV blend can be knitted to form mesh with good mechanical properties. • PBAT and PHBV blend do not show significant weight loss over a period of 8 weeks in PBS. • Osteoblast cell culture was done on these samples. • They support extracellular matrix and growth and hence are osteoconductive

Osteoconductive bio-based meshes based on Poly(hydroxybutyrate-co-hydroxyvalerate) and poly(butylene adipate-co-terephthalate) blends

Energy Technology Data Exchange (ETDEWEB)

Nar, Mangesh; Staufenberg, Gerrit; Yang, Bing [Department of Material Science and Engineering, University of North Texas, 1155 Union Circle #305310, Denton, TX 76203-5017 (United States); Robertson, Lesli [Department of Fibers, College of Visual Arts and Design, 1155 Union Circle #305100, Denton, TX 76203-5017 (United States); Patel, Rinkesh H. [Department of Biomedical Sciences and Center for Craniofacial Research and Diagnosis, Texas A and M University Baylor College of Dentistry, Dallas, TX 75246 (United States); Varanasi, Venu G., E-mail: vvaranasi@bcd.tamhsc.edu [Department of Biomedical Sciences and Center for Craniofacial Research and Diagnosis, Texas A and M University Baylor College of Dentistry, Dallas, TX 75246 (United States); D' Souza, Nandika Anne, E-mail: nandika.dsouza@unt.edu [Department of Material Science and Engineering, University of North Texas, 1155 Union Circle #305310, Denton, TX 76203-5017 (United States); Department of Mechanical and Energy Engineering, University of North Texas, 1155 Union Circle # 311098, Denton, TX 76203-5017 (United States)

2014-05-01

Poly(butylene adipate-co-terephthalate) (PBAT) and Poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) are biopolymers that have the potential to be used in applications of bone healing. In this study, it is hypothesized that the polymer blend has the combined strength and osteoconductivity to support osteoblast collagen formation. PBAT (PBAT 100), and a blend with 20% PHBV (PBAT 80) were extruded in the form of fibers and then knitted in the form of mesh. These were tested in the warp as well as weft direction for the tensile properties; these showed that the weft direction had higher performance than the warp. The individual fibers were kept in phosphate buffered saline (PBS) over the period of 8 weeks and were tested for the storage and loss modulus using a dynamic mechanical analyser (DMA). The results indicated that mechanical relaxation strength showed a decrease and then an increase. In vitro osteoconductivity studies were done by using differentiating osteoblasts (MC3T3-E1 subclone 4 cells). Environmental Scanning Electron Microscopy (ESEM) showed that pre-soaking the samples in α-MEM for two weeks resulted in cell attachment and growth. X-ray diffraction (XRD) was used to determine the change in structure of polymers due to in vitro degradation for two weeks. Raman spectroscopy showed that all scaffolds supported the formation of a collagenous network over the scaffold surfaces. For a combination of knittable manufacturing, mechanical performance and osteoconductivity, blends offer an effective route. - Highlights: • PBAT and PHBV blend can be knitted to form mesh with good mechanical properties. • PBAT and PHBV blend do not show significant weight loss over a period of 8 weeks in PBS. • Osteoblast cell culture was done on these samples. • They support extracellular matrix and growth and hence are osteoconductive.

Blended Learning over Two Decades

Science.gov (United States)

Zhonggen, Yu; Yuexiu, Zhejiang

2015-01-01

The 21st century has witnessed vast amounts of research into blended learning since the conception of online learning formed the possibility of blended learning in the early 1990s. The theme of this paper is blended learning in mainstream disciplinary communities. In particular, the paper reports on findings from the last two decades which looked…

Evaporation characteristics of ETBE-blended gasoline.

Science.gov (United States)

Okamoto, Katsuhiro; Hiramatsu, Muneyuki; Hino, Tomonori; Otake, Takuma; Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi

2015-04-28

To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were developed. Copyright © 2015 Elsevier B.V. All rights reserved.

Evaporation characteristics of ETBE-blended gasoline

International Nuclear Information System (INIS)

Okamoto, Katsuhiro; Hiramatsu, Muneyuki; Hino, Tomonori; Otake, Takuma; Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi

2015-01-01

Highlights: • We chose 8-component hydrocarbon mixture as a model gasoline, and defined the molar mass of gasoline. • We proposed an evaporation model assuming a 2-component mixture of gasoline and ETBE. • We predicted the change in the vapor pressure of ETBE-blended gasoline by evaporation. • The vapor pressures were measured and compared as a means of verifying the model. • We presented the method for predicting flash points of the ETBE-blended gasoline. - Abstract: To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were

Evaporation characteristics of ETBE-blended gasoline

Energy Technology Data Exchange (ETDEWEB)

Okamoto, Katsuhiro, E-mail: okamoto@nrips.go.jp [National Research Institute of Police Science, 6-3-1 Kashiwanoha, Kashiwa, Chiba 277-0882 (Japan); Hiramatsu, Muneyuki [Yamanashi Prefectural Police H.Q., 312-4 Kubonakajima, Isawa-cho, Usui, Yamanashi 406-0036 (Japan); Hino, Tomonori; Otake, Takuma [Metropolitan Police Department, 2-1-1 Kasumigaseki, Chiyoda-ku, Tokyo 100-8929 (Japan); Okamoto, Takashi; Miyamoto, Hiroki; Honma, Masakatsu; Watanabe, Norimichi [National Research Institute of Police Science, 6-3-1 Kashiwanoha, Kashiwa, Chiba 277-0882 (Japan)

2015-04-28

Highlights: • We chose 8-component hydrocarbon mixture as a model gasoline, and defined the molar mass of gasoline. • We proposed an evaporation model assuming a 2-component mixture of gasoline and ETBE. • We predicted the change in the vapor pressure of ETBE-blended gasoline by evaporation. • The vapor pressures were measured and compared as a means of verifying the model. • We presented the method for predicting flash points of the ETBE-blended gasoline. - Abstract: To reduce greenhouse gas emissions, which contribute to global warming, production of gasoline blended with ethyl tert-buthyl ether (ETBE) is increasing annually. The flash point of ETBE is higher than that of gasoline, and blending ETBE into gasoline will change the flash point and the vapor pressure. Therefore, it is expected that the fire hazard caused by ETBE-blended gasoline would differ from that caused by normal gasoline. The aim of this study was to acquire the knowledge required for estimating the fire hazard of ETBE-blended gasoline. Supposing that ETBE-blended gasoline was a two-component mixture of gasoline and ETBE, we developed a prediction model that describes the vapor pressure and flash point of ETBE-blended gasoline in an arbitrary ETBE blending ratio. We chose 8-component hydrocarbon mixture as a model gasoline, and defined the relation between molar mass of gasoline and mass loss fraction. We measured the changes in the vapor pressure and flash point of gasoline by blending ETBE and evaporation, and compared the predicted values with the measured values in order to verify the prediction model. The calculated values of vapor pressures and flash points corresponded well to the measured values. Thus, we confirmed that the change in the evaporation characteristics of ETBE-blended gasoline by evaporation could be predicted by the proposed model. Furthermore, the vapor pressure constants of ETBE-blended gasoline were obtained by the model, and then the distillation curves were

AKRO/SF: Blend System

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Blend was the system used by the NMFS Alaska Regional Office to monitor groundfish catch from 1991 until 2002. The Blend system combined data from industry...

Tritium extraction mechanisms from lithium aluminates during in pile irradiation experiments

International Nuclear Information System (INIS)

Briec, M.; Roth, E.

1987-04-01

The principal aim was to determine ranges of parameters governing tritium release from γ lithium aluminates within which acceptable rates for their contemplated usage as tritium breeder material in a fusion reactor blanket could be obtained. in the first place values of every quantity involved should be known as well as possible. Reproducible results should be a criterium of validity of the selected parameters. It is shown from a description of a series of experiments that processes limiting tritium release rates are not the same in different temperature ranges. By varying the composition of purge gases used for tritium extraction, the level of irradiation fluxes, and by studying simultaneously samples of different textures, results were obtained and an assignment of the respective role of defect formation, texture, surface effect is attempted to interpret them

Creep of Polycrystalline Magnesium Aluminate Spinel Studied by an SPS Apparatus.

Science.gov (United States)

Ratzker, Barak; Sokol, Maxim; Kalabukhov, Sergey; Frage, Nachum

2016-06-20

A spark plasma sintering (SPS) apparatus was used for the first time as an analytical testing tool for studying creep in ceramics at elevated temperatures. Compression creep experiments on a fine-grained (250 nm) polycrystalline magnesium aluminate spinel were successfully performed in the 1100-1200 °C temperature range, under an applied stress of 120-200 MPa. It was found that the stress exponent and activation energy depended on temperature and applied stress, respectively. The deformed samples were characterized by high resolution scanning electron microscope (HRSEM) and high resolution transmission electron microscope (HRTEM). The results indicate that the creep mechanism was related to grain boundary sliding, accommodated by dislocation slip and climb. The experimental results, extrapolated to higher temperatures and lower stresses, were in good agreement with data reported in the literature.

Conditioning highly concentrated borate solutions with calcium sulfo-aluminate cement

International Nuclear Information System (INIS)

Champenois, J.B.; Cau dit Coumes, C.; Poulesquen, A.; Le Bescop, P.; Damidot, D.

2012-01-01

The early age hydration by borate solution of 3 calcium sulfo-aluminate cements (CSA), containing respectively 0%, 10% and 20% of gypsum by weight of cement was studied using isothermal calorimetry and dynamic mode rheo-metry. XRD and TGA analysis were carried out on pastes with increasing hydration degrees (up to 90 days) to specify the mineralogy and to figure out the mechanisms of borate immobilisation. It has been shown that the retarding effect of borate anions is due to the precipitation of the amorphous calcium borate C 2 B 3 H 8 ; borate anions were then incorporated in Aft-type phases. The macroscopic properties of hydrated binders (compressive strength, length change) were also followed during 180 days. It appears that the mechanical strength continuously increases with the hydration degree. Length changes under wet-curing and sealed bag remain moderate and seem to be stabilized after 180 days

Evaluation of bioactivity in vitro of endodontic calcium aluminate cement

International Nuclear Information System (INIS)

Oliveira, I.R.; Andrade, T.L.; Santos, G.L.; Pandolfelli, V.C.

2011-01-01

Bioactivity is referred to as the capacity of a material to develop a stable bond with living tissue via the deposition of hydroxyapatite. Materials which exhibit this property can be used to repair diseased or damaged bone tissue and can be designed to remain in situ indefinitely. An indication of bioactivity can be obtained by the formation of a hydroxyapatite layer on the surface of a substrate in simulated body fluids (SBF) in vitro. Therefore, set samples of calcium aluminate endodontic cement were maintained in contact with SBF solutions (Kokubo and Rigo) and their surfaces were later evaluated by means of SEM, EDX and DRX. Measurements of pH and ionic conductivity were also carried out for SBF solutions in contact with set samples of endodontic cement. The ideal conditions of precipitation were obtained in SBF Rigo been observed a surface layer with spherical morphology characteristic of stoichiometric hydroxyapatite.(author)

Entanglement in miscible blends

Science.gov (United States)

Watanabe, Hiroshi

2010-03-01

The entanglement length Le of polymer chains (corresponding to the entanglement molecular weight Me) is not an intrinsic material parameter but changes with the interaction with surrounding chains. For miscible blends of cis-polyisoprene (PI) and poly(tert-butyl styrene) (PtBS), changes of Le on blending was examined. It turned out that the Le averaged over the number fractions of the Kuhn segments of the components (PI and PtBS) satisfactorily describes the viscoelastic behavior of pseudo-monodisperse blends in which the terminal relaxation time is the same for PI and PtBS.

Miscibility evolution of polycarbonate/polystyrene blends during compounding

DEFF Research Database (Denmark)

Chuai, Chengzhi; Almdal, Kristoffer; Johannsen, Ib

2002-01-01

The miscibility evolution of polycarbonate/polystyrene (PC/PS) blends during the compounding process in three blending methods of industrial relevance, namely melt blending, remelt blending in a twin-screw extruder and third melt blending in an injection molding machine, was investigated...... polymer in the other. The observed solubility strongly depends on blend composition and blending method. The T-g measurements showed maximum mutual solubility around 50/50 composition. The miscibility of PC/PS blended after the third stage (melt injection molding) was higher than that after the first...... by measuring their glass transition temperatures (T-g) and their specific heat increment (DeltaC(p)). Differential scanning calorimetry (DSC) was used to examine nine blend compositions. Shifts in glass transition temperature (T-g) of the two phases in melt-mixed PC/PS blends suggest partial miscibility of one...

Effects of Blended-Cement Paste Chemical Composition Changes on Some Strength Gains of Blended-Mortars

Science.gov (United States)

Kirgiz, Mehmet Serkan

2014-01-01

Effects of chemical compositions changes of blended-cement pastes (BCPCCC) on some strength gains of blended cement mortars (BCMSG) were monitored in order to gain a better understanding for developments of hydration and strength of blended cements. Blended cements (BC) were prepared by blending of 5% gypsum and 6%, 20%, 21%, and 35% marble powder (MP) or 6%, 20%, 21%, and 35% brick powder (BP) for CEMI42.5N cement clinker and grinding these portions in ball mill at 30 (min). Pastes and mortars, containing the MP-BC and the BP-BC and the reference cement (RC) and tap water and standard mortar sand, were also mixed and they were cured within water until testing. Experiments included chemical compositions of pastes and compressive strengths (CS) and flexural strengths (FS) of mortars were determined at 7th-day, 28th-day, and 90th-day according to TS EN 196-2 and TS EN 196-1 present standards. Experimental results indicated that ups and downs of silica oxide (SiO2), sodium oxide (Na2O), and alkali at MP-BCPCC and continuously rising movement of silica oxide (SiO2) at BP-BCPCC positively influenced CS and FS of blended cement mortars (BCM) in comparison with reference mortars (RM) at whole cure days as MP up to 6% or BP up to 35% was blended for cement. PMID:24587737

Effects of Blended-Cement Paste Chemical Composition Changes on Some Strength Gains of Blended-Mortars

Directory of Open Access Journals (Sweden)

Mehmet Serkan Kirgiz

2014-01-01

Full Text Available Effects of chemical compositions changes of blended-cement pastes (BCPCCC on some strength gains of blended cement mortars (BCMSG were monitored in order to gain a better understanding for developments of hydration and strength of blended cements. Blended cements (BC were prepared by blending of 5% gypsum and 6%, 20%, 21%, and 35% marble powder (MP or 6%, 20%, 21%, and 35% brick powder (BP for CEMI42.5N cement clinker and grinding these portions in ball mill at 30 (min. Pastes and mortars, containing the MP-BC and the BP-BC and the reference cement (RC and tap water and standard mortar sand, were also mixed and they were cured within water until testing. Experiments included chemical compositions of pastes and compressive strengths (CS and flexural strengths (FS of mortars were determined at 7th-day, 28th-day, and 90th-day according to TS EN 196-2 and TS EN 196-1 present standards. Experimental results indicated that ups and downs of silica oxide (SiO2, sodium oxide (Na2O, and alkali at MP-BCPCC and continuously rising movement of silica oxide (SiO2 at BP-BCPCC positively influenced CS and FS of blended cement mortars (BCM in comparison with reference mortars (RM at whole cure days as MP up to 6% or BP up to 35% was blended for cement.

Introducing blended e-learning course design

DEFF Research Database (Denmark)

Gyamfi, Samuel Adu; Ryberg, Thomas

2012-01-01

In the face of diminishing education budgets in higher education, blended learning has been found to be a viable and effective approach to deliver high-quality, up-to-date, on-demand solutions to developing cross-curricular skills of undergraduates. However, research has also shown that blended...... learning solutions do not often live up to the potential of the approach or fail to produce the intended results because the students are not always equipped to handle the technical, psychological and organisational challenges of blended learning approaches. This project surveyed seventy-five first year...... the students’ e-readiness for an implementation of a blend-ed course design....

Preparation and corrosion resistance of a nanocomposite plasma electrolytic oxidation coating on Mg-1%Ca alloy formed in aluminate electrolyte containing titania nano-additives

DEFF Research Database (Denmark)

Daroonparvar, Mohammadreza; Yajid, M. A. M.; Yusof, N. M.

2016-01-01

Titania nanoparticles were utilized as suspension in alkaline aluminate electrolyte to form nanocomposite coatings on magnesium alloy containing 1 wt% calcium by plasma electrolytic oxidation process. Microhardness, wettability, potentiodynamic polarization, wettability, electrochemical impedance...

Space Environmental Effects Testing and Characterization of the Candidate Solar Sail Material Aluminized Mylar

Science.gov (United States)

Edwards, D. L.; Hubbs, W. S.; Wertz, G. E.; Alstatt, R.; Munafo, Paul (Technical Monitor)

2001-01-01

The usage of solar sails as a propellantless propulsion system has been proposed for many years. The technical challenges associated with solar sails are fabrication of ultralightweight films, deploying the sails and controlling the spacecraft. Integral to all these challenges is the mechanical property integrity of the sail while exposed to the harsh environment of space. This paper describes testing and characterization of a candidate solar sail material, Aluminized Mylar. This material was exposed to a simulated Geosynchronous Transfer Orbit (GTO) and evaluated by measuring thermooptical and mechanical property changes. Testing procedures and results are presented.

Effect of surface modification of nanofibres with glutamic acid peptide on calcium phosphate nucleation and osteogenic differentiation of marrow stromal cells.

Science.gov (United States)

Karaman, Ozan; Kumar, Ankur; Moeinzadeh, Seyedsina; He, Xuezhong; Cui, Tong; Jabbari, Esmaiel

2016-02-01

Biomineralization is mediated by extracellular matrix (ECM) proteins with amino acid sequences rich in glutamic acid. The objective of this study was to investigate the effect of calcium phosphate deposition on aligned nanofibres surface-modified with a glutamic acid peptide on osteogenic differentiation of rat marrow stromal cells. Blend of EEGGC peptide (GLU) conjugated low molecular weight polylactide (PLA) and high molecular weight poly(lactide-co-glycolide) (PLGA) was electrospun to form aligned nanofibres (GLU-NF). The GLU-NF microsheets were incubated in a modified simulated body fluid for nucleation of calcium phosphate crystals on the fibre surface. To achieve a high calcium phosphate to fibre ratio, a layer-by-layer approach was used to improve diffusion of calcium and phosphate ions inside the microsheets. Based on dissipative particle dynamics simulation of PLGA/PLA-GLU fibres, > 80% of GLU peptide was localized to the fibre surface. Calcium phosphate to fibre ratios as high as 200%, between those of cancellous (160%) and cortical (310%) bone, was obtained with the layer-by-layer approach. The extent of osteogenic differentiation and mineralization of marrow stromal cells seeded on GLU-NF microsheets was directly related to the amount of calcium phosphate deposition on the fibres prior to cell seeding. Expression of osteogenic markers osteopontin, alkaline phosphatase (ALP), osteocalcin and type 1 collagen increased gradually with calcium phosphate deposition on GLU-NF microsheets. Results demonstrate that surface modification of aligned synthetic nanofibres with EEGGC peptide dramatically affects nucleation and growth of calcium phosphate crystals on the fibres leading to increased osteogenic differentiation of marrow stromal cells and mineralization. Copyright © 2013 John Wiley & Sons, Ltd.

Coalescence in PLA-PBAT blends under shear flow: Effects of blend preparation and PLA molecular weight

Energy Technology Data Exchange (ETDEWEB)

Nofar, M. [Center for High Performance Polymer and Composite Systems (CREPEC), Chemical Engineering Department, Polytechnique Montreal, Montreal, Quebec H3T 1J4, Canada and CREPEC, Department of Chemical Engineering, McGill University, Montreal, Quebec H3A 2B2 (Canada); Heuzey, M. C.; Carreau, P. J., E-mail: pierre.carreau@polymtl.ca [Center for High Performance Polymer and Composite Systems (CREPEC), Chemical Engineering Department, Polytechnique Montreal, Montreal, Quebec H3T 1J4 (Canada); Kamal, M. R. [CREPEC, Department of Chemical Engineering, McGill University, Montreal, Quebec H3A 2B2 (Canada); Randall, J. [NatureWorks LLC, 15305 Minnetonka Boulevard, Minnetonka, Minnesota 55345 (United States)

2016-07-15

Blends containing 75 wt. % of an amorphous polylactide (PLA) with two different molecular weights and 25 wt. % of a poly[(butylene adipate)-co-terephthalate] (PBAT) were prepared using either a Brabender batch mixer or a twin-screw extruder. These compounds were selected because blending PLA with PBAT can overcome various drawbacks of PLA such as its brittleness and processability limitations. In this study, we investigated the effects of varying the molecular weight of the PLA matrix and of two different mixing processes on the blend morphology and, further, on droplet coalescence during shearing. The rheological properties of these blends were investigated and the interfacial properties were analyzed using the Palierne emulsion model. Droplet coalescence was investigated by applying shear flows of 0.05 and 0.20 s{sup −1} at a fixed strain of 60. Subsequently, small amplitude oscillatory shear tests were conducted to investigate changes in the viscoelastic properties. The morphology of the blends was also examined using scanning electron microscope (SEM) micrographs. It was observed that the PBAT droplets were much smaller when twin-screw extrusion was used for the blend preparation. Shearing at 0.05 s{sup −1} induced significant droplet coalescence in all blends, but coalescence and changes in the viscoelastic properties were much more pronounced for the PLA-PBAT blend based on a lower molecular weight PLA. The viscoelastic responses were also somehow affected by the thermal degradation of the PLA matrix during the experiments.

Coalescence in PLA-PBAT blends under shear flow: Effects of blend preparation and PLA molecular weight

International Nuclear Information System (INIS)

Nofar, M.; Heuzey, M. C.; Carreau, P. J.; Kamal, M. R.; Randall, J.

2016-01-01

Blends containing 75 wt. % of an amorphous polylactide (PLA) with two different molecular weights and 25 wt. % of a poly[(butylene adipate)-co-terephthalate] (PBAT) were prepared using either a Brabender batch mixer or a twin-screw extruder. These compounds were selected because blending PLA with PBAT can overcome various drawbacks of PLA such as its brittleness and processability limitations. In this study, we investigated the effects of varying the molecular weight of the PLA matrix and of two different mixing processes on the blend morphology and, further, on droplet coalescence during shearing. The rheological properties of these blends were investigated and the interfacial properties were analyzed using the Palierne emulsion model. Droplet coalescence was investigated by applying shear flows of 0.05 and 0.20 s"−"1 at a fixed strain of 60. Subsequently, small amplitude oscillatory shear tests were conducted to investigate changes in the viscoelastic properties. The morphology of the blends was also examined using scanning electron microscope (SEM) micrographs. It was observed that the PBAT droplets were much smaller when twin-screw extrusion was used for the blend preparation. Shearing at 0.05 s"−"1 induced significant droplet coalescence in all blends, but coalescence and changes in the viscoelastic properties were much more pronounced for the PLA-PBAT blend based on a lower molecular weight PLA. The viscoelastic responses were also somehow affected by the thermal degradation of the PLA matrix during the experiments.

Morphology Evolution of Polycarbonate-Polystyrene Blends During Compounding

DEFF Research Database (Denmark)

Chuai, Chengzhi; Almdal, Kristoffer; Johannsen, Ib

2001-01-01

The morphology evolution of polycarbonate-polystyrene (PC/PS) blends during the compounding process in three blending methods of industrial relevance, namely melt blending, re-melt blending in a twin-screw extruder and tri-melt blending in an injection-moulding machine, was investigated using......-empirical model. The results show that the formation of co-continuous morphology strongly depends on blend composition and melt blending method, whereas the model prediction for phase inversion deviates from the experimental values. Further, we found that the initial mechanism of morphology evolution involves...... scanning electron microscopy (SEM) Co examine nine blend compositions. Blends were prepared at compositions where phase inversion was expected to occur according to model predictions. The experimental results were compared to the values of the point of phase inversion calculated with the semi...

Chemical synthesis of nanocrystalline magnesium aluminate spinel via nitrate-citrate combustion route

International Nuclear Information System (INIS)

Saberi, Ali; Golestani-Fard, Farhad; Sarpoolaky, Hosein; Willert-Porada, Monika; Gerdes, Thorsten; Simon, Reinhard

2008-01-01

Nanocrystalline magnesium aluminate spinel (MgAl 2 O 4 ) was synthesized using metal nitrates, citric acid and ammonium solutions. The precursor and the calcined powders at different temperatures were characterized by X-ray diffraction (XRD), simultaneous thermal analysis (STA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The combustion mechanism was also studied by a quadrupole mass spectrometer (QMS) which coupled to STA. The generated heat through the combustion of the mixture of ammonium nitrate and citrate based complexes decreased the synthesis temperature of MgAl 2 O 4 spinel. The synthesized MgAl 2 O 4 spinel at 900 deg. C has faced shape with crystallite size in the range of 18-24 nm

Photocatalytic NO{sub x} abatement by calcium aluminate cements modified with TiO{sub 2}: Improved NO{sub 2} conversion

Energy Technology Data Exchange (ETDEWEB)

Pérez-Nicolás, M. [MIMED Research Group, Department of Chemistry and Soil Sciences, School of Sciences, University of Navarra, c/Irunlarrea, 1, 31008 Pamplona (Spain); Balbuena, J.; Cruz-Yusta, M.; Sánchez, L. [Department of Inorganic Chemistry, School of Sciences, University of Córdoba, Campus de Rabanales, Edificio Marie Curie, 14071 Córdoba (Spain); Navarro-Blasco, I.; Fernández, J.M. [MIMED Research Group, Department of Chemistry and Soil Sciences, School of Sciences, University of Navarra, c/Irunlarrea, 1, 31008 Pamplona (Spain); Alvarez, J.I., E-mail: jalvarez@unav.es [MIMED Research Group, Department of Chemistry and Soil Sciences, School of Sciences, University of Navarra, c/Irunlarrea, 1, 31008 Pamplona (Spain)

2015-04-15

Photocatalytic activity of TiO{sub 2} was studied in two types of calcium aluminate cement (CAC) under two different curing regimes. The effect of the TiO{sub 2} addition on the setting time, consistency and mechanical properties of the CACs was evaluated. The abatement of gaseous pollutants (NO{sub x}) under UV irradiation was also assessed. These cementitious matrices were found to successfully retain NO{sub 2}: more abundant presence of aluminates in white cement (w-CAC, iron-lean) helped to better adsorb NO{sub 2}, thus improving the conversion performance of the catalyst resulting in a larger NO{sub x} removal under UV irradiation. As evidenced by XRD, SEM, EDAX and zeta potential analyses, the presence of ferrite in dark cement (d-CAC, iron-reach) induced a certain chemical interaction with TiO{sub 2}. The experimental findings suggest the formation of new iron titanate phases, namely pseudobrookite. The reduced band-gap energy of these compounds compared with that of TiO{sub 2} accounts for the photocatalytic activity of these samples.

Blended Learning Design

DEFF Research Database (Denmark)

Pedersen, Lise

2015-01-01

University College Lillebaelt has decided that 30 percent of all educational elements must be generated as blended learning by the end of the year 2015 as part of a modernization addressing following educational needs: 1. Blended learning can help match the expectations of the future students who...... learning. 4. Blended learning can contribute to supporting and improving efficiency of educational efforts. This can for instance be done through programmes for several classes by using video conferencing, allocating traditional face to face teaching to synchronous and asynchronous study activities produce...... digital materials which can be employed didactically and reused by the teachers. This can also mean that the particular competencies which teaches have in Svendborg can be used at other locations in UCL and disseminated to a larger group of students without further costs. Educational Innovation...

High-Temperature Self-Healing and Re-Adhering Geothermal Well Cement Composites

Science.gov (United States)

Pyatina, T.; Sugama, T.; Boodhan, Y.; Nazarov, L.

2017-12-01

Self-healing cementitious materials are particularly attractive for the cases where damaged areas are difficult to locate and reach. High-temperature geothermal wells with aggressive environments impose most difficult conditions on cements that must ensure durable zonal isolation under repeated thermal, chemical and mechanical stresses. The present work evaluates matrix and carbon steel (CS) - cement interface self-healing and re-adhering properties of various inorganic cementitious composites under steam, alkali carbonate or brine environments at 270-300oC applicable to geothermal wells. The composite materials included blends based on Ordinary Portland Cement (OPC) and natural zeolites and alkali or phosphate activated composites of Calcium Aluminate Cement (CAC) with fly ash, class F. Class G cement blend with crystalline silica was used as a baseline. Compressive-strength and bond-strength recoveries were examined to evaluate self-healing and re-adhering properties of the composites after repeated crush tests followed by 5-day healing periods in these environments. The optical and scanning electron microscopes, X-ray diffraction, Fourier Transform infrared, Raman spectroscopy and EDX measurements were used to identify phases participating in the strengths recoveries and cracks filling processes. Amorphous silica-rich- and small-size crystalline phases played an important role in the healing of the tested composites in all environments. Possible ways to enhance self-healing properties of cementitious composites under conditions of geothermal wells were identified.

Blended Learning: How Teachers Balance the Blend of Online and Classroom Components

Science.gov (United States)

Jeffrey, Lynn M.; Milne, John; Suddaby, Gordon

2014-01-01

Despite teacher resistance to the use of technology in education, blended learning has increased rapidly, driven by evidence of its advantages over either online or classroom teaching alone. However, blended learning courses still fail to maximize the benefits this format offers. Much research has been conducted on various aspects of this problem,…

Synthesis and optical property of zinc aluminate spinel cryogels

Directory of Open Access Journals (Sweden)

Lifen Su

2016-06-01

Full Text Available Zinc aluminate spinel cryogels with various molar ratio of Al/Zn are synthesized by sol–gel technology followed by vacuum freeze drying. The structures and optical properties are both found to be affected by the molar ratios of Al/Zn and annealed temperatures. The peaks of zinc oxide (ZnO and zinc dialuminum oxide (ZnAl2O4 are both obtained for the samples with more Zn content annealed at 750 °C or upward. The composites have a large surface area (137 m2/g with mesoporous structure after annealing at 750 °C. The SEM images reveal that the ZnAl2O4 crystals formed a multilayer structure with redundant ZnO particles which deposited on it. Furthermore, the maximum infrared reflectance is about 80% with an improvement of 35% in the infrared region after annealing at 950 °C compared with that of 450 °C, which indicates that these porous cryogels have a potential application as thermal insulating materials at a high temperature.

Thin films of polymer blends deposited by matrix-assisted pulsed laser evaporation: Effects of blending ratios

International Nuclear Information System (INIS)

Paun, Irina Alexandra; Ion, Valentin; Moldovan, Antoniu; Dinescu, Maria

2011-01-01

In this work, we show successful use of matrix-assisted pulsed laser evaporation (MAPLE) for obtaining thin films of PEG:PLGA blends, in the view of their use for controlled drug delivery. In particular, we investigate the influence of the blending ratios on the characteristics of the films. We show that the roughness of the polymeric films is affected by the ratio of each polymer within the blend. In addition, we perform Fourier transformed infrared spectroscopy (FTIR) measurements and we find that the intensities ratios of the infrared absorption bands of the two polymers are consistent with the blending ratios. Finally, we assess the optical constants of the polymeric films by spectroscopic ellipsometry (SE). We point out that the blending ratios exert an influence on the optical characteristics of the films and we validate the SE results by atomic force microscopy and UV-vis spectrophotometry. In all, we stress that the ratios in which the two polymers are blended have significant impact on the morphology, chemical structure and optical characteristics of the polymeric films deposited by MAPLE.

Emissions characteristics of higher alcohol/gasoline blends

International Nuclear Information System (INIS)

Gautam, M.; Martin, D.W.; Carder, D.

2000-01-01

An experimental investigation was conducted to determine the emissions characteristics of higher alcohols and gasoline (UTG96) blends. While lower alcohols (methanol and ethanol) have been used in blends with gasoline, very little work has been done or reported on higher alcohols (propanol, butanol and pentanol). Comparisons of emissions and fuel characteristics between higher alcohol/gasoline blends and neat gasoline were made to determine the advantages and disadvantages of blending higher alcohols with gasoline. All tests were conducted on a single-cylinder Waukesha Cooperative Fuel Research engine operating at steady state conditions and stoichiometric air-fuel (A/F) ratio. Emissions test were conducted at the optimum spark timing-knock limiting compression ratio combination for the particular blend being tested. The cycle emission [mass per unit time (g/h)] of CO, CO 2 and organic matter hydrocarbon equivalent (OMHCE) from the higher alcohol/gasoline blends were very similar to those from neat gasoline. Cycle emissions of NO x from the blends were higher than those from neat gasoline. However, for all the emissions species considered, the brake specific emissions (g/kW h) were significantly lower for the higher alcohol/gasoline blends than for neat gasoline. This was because the blends had greater resistance to knock and allowed higher compression ratios, which increased engine power output. The contribution of alcohols and aldehydes to the overall OMHCE emissions was found to be minimal. Cycle fuel consumption (g/h) of higher alcohol/gasoline blends was slightly higher than with neat gasoline due to the lower stoichiometric A/F ratios required by the blends. However, the brake specific fuel consumption (g/kW h) for the blends was significantly lower than that for neat gasoline. (Author)

Effect of fly ash composition on the sulfate resistance of concrete[Includes the CSCE forum on professional practice and career development : 1. international engineering mechanics and materials specialty conference : 1. international/3. coastal, estuarine and offshore engineering specialty conference : 2. international/8. construction specialty conference

Energy Technology Data Exchange (ETDEWEB)

Dhole, R.D.; Thomas, M.D.A. [New Brunswick Univ., Fredericton, NB (Canada); Folliard, K.J.; Drimalas, T. [Texas Univ., Austin, TX (United States)

2009-07-01

Studies have shown that low-calcium Class F fly ashes obtained from burning coal in power stations can increase the sulfate resistance of Portland cement concrete. In many cases the sulfate resistance of concrete containing high-calcium Class C fly ash can be reduced compared to concrete without fly ash, due to the presence of crystalline C3A in the fly ash and calcium aluminate in the glass. This study investigated the differences in the glass composition and sulfate resistance of fly ashes with a range of calcium contents. The objective was to determine whether the behaviour of high-calcium fly ashes could be improved by blending with low-calcium fly ash. The sulfate resistance of cementitious systems consisting of a Type I Portland cement blended with Class F and Class C fly ashes of varying composition was evaluated by monitoring the length change of mortar bars stored in 5 per cent sodium sulfate solution. Scanning electron microscopy and electron dispersive X-ray analysis were used to characterize the glass phases of the fly ashes. The position occupied by the glass when plotted on a CaO-SiO{sub 2}-Al{sub 2}O{sub 3} ternary was identified as belonging to one of the fields occupied by the mineral phases mullite, anorthosite or gehlenite. The glass showed a transition from alumino-silicate in Class F fly ash to a calcium alumino-silicate or mixed calcium-aluminate/alumino-silicate in Class C fly ashes with higher calcium contents. Fly ashes with high amounts of calcium-aluminate glass had reduced sulfate resistance when tested in mortars. Blends of Class C and Class F fly ashes had better sulfate resistance than mixes made with only Class C fly ash. A relationship was established between the calcium oxide content of the blended fly ash and sulfate resistance of mortar. 8 refs., 5 tabs., 10 figs.

Moessbauer study on the crystallization of IR-transmitting aluminate glasses

International Nuclear Information System (INIS)

Kubuki, S.; Nishida, T.

1999-01-01

Heat treatment of 60CaO x 10BaO x 17Al 2 O 3 x 13Fe 2 O 3 glass causes a precipitation of the nanoparticles of antiferromagnetic Ca 2 Fe 2 O 5 and ferromagnetic BaFe 2 O 4 . Moessbauer spectra of these glass-ceramics show a magnetic relaxation spectra superimposed on doublets. A Kissinger plot in the DTA Method reveals that simultaneous cleavage of Ca-O and Fe-O bonds and that of Ba-O and Fe-O bonds cause the precipitation of Ca 2 Fe 2 O 5 and BaFe 2 O 4 , respectively. Introduction of Fe(III) promotes the crystallization of aluminate glass. In the case of iron-free 60CaO x 10BaO x 30Al 2 O 3 glass, Ca 2 Al 2 O 5 and BaAl 2 O 4 particles precipitate instead of Ca 2 Fe 2 O 5 and BaFe 2 O 4 particles, respectively. (author)

40 CFR 80.82 - Butane blending.

Science.gov (United States)

2010-07-01

... FUELS AND FUEL ADDITIVES Reformulated Gasoline § 80.82 Butane blending. A refiner for any refinery that produces gasoline by blending butane with conventional gasoline or reformulated gasoline or RBOB may meet... paragraph (b)(1) of this section, the refiner may: (i) Blend the butane with conventional gasoline, or...

Development of high-performance blended cements

Science.gov (United States)

Wu, Zichao

2000-10-01

This thesis presents the development of high-performance blended cements from industrial by-products. To overcome the low-early strength of blended cements, several chemicals were studied as the activators for cement hydration. Sodium sulfate was discovered as the best activator. The blending proportions were optimized by Taguchi experimental design. The optimized blended cements containing up to 80% fly ash performed better than Type I cement in strength development and durability. Maintaining a constant cement content, concrete produced from the optimized blended cements had equal or higher strength and higher durability than that produced from Type I cement alone. The key for the activation mechanism was the reaction between added SO4 2- and Ca2+ dissolved from cement hydration products.

The preparation of lithium aluminate by the hydrolysis of lithium and aluminum alkoxides

International Nuclear Information System (INIS)

Turner, C.W.; Clatworthy, B.C.; Gin, A.Y.H.

1987-10-01

Lithium aluminate was prepared by heating the hydrolysis products from various combinations of lithium and aluminum alkoxides under an atmosphere of nitrogen. The product was β-LiA1O 2 when aluminum iso-propoxide was a starting material, whereas γ-LiA1O 2 was the product for preparations starting with aluminum n-butoxide. The results were independent of the choice of lithium alkoxide. The hydrolysis of aluminum sec-butoxide with a solution of LiOH led to the γ phase as well. The temperature at which the γ phase developed depended upon the conditions of the hydrolysis reaction and was observed at a temperature as low as 550 degrees Celcius

THE COMBUSTION CHARACTERISTICS OF LIGNITE BLENDS

Institute of Scientific and Technical Information of China (English)

Cheng Jun; Zhou Junhu; Cao Xinyu; Cen Kefa

2000-01-01

The combustion characteristics of lignite blends were studied with a thermogravimetric analyzer (t.g.a.), at constant heating rate.The characteristic temperatures were determined from the burning profiles.It was found that the characteristic times of combustion reaction moved forward, the ignition temperature dropped and the burnout efficiency slightly changed when blending lignites.The characteristic parameters of blends could not be predicted as a linear function of the average values of the individual lignites.when blending with less reactive coal, the ignition and burnout characteristics of lignite turned worse.

Structural characterization of HDPE/LLDPE blend-based nano composites obtained by different blending sequence

International Nuclear Information System (INIS)

Passador, Fabio R.; Ruvolo Filho, Adhemar; Pessan, Luiz A.

2011-01-01

The blending sequence affects the morphology formation of the nanocomposites. In this work, the blending sequences were explored to determine its influence in the rheological behavior of HDPE/LLDPE/OMMT nanocomposites. The nanocomposites were obtained by melt-intercalation using a mixture of LLDPE-g-MA and HDPE-g-MA as compatibilizer system in a torque rheometer at 180 deg C and five blending sequences were studied. The materials structures were characterized by wide angle X-ray diffraction (WAXD) and by rheological properties. The nanoclay's addition increased the shear viscosity at low shear rates, changing the behavior of HDPE/LLDPE matrix to a Bingham model behavior with an apparent yield stress. Intense interactions were obtained for the blending sequence where LLDPE and/or LLDPE-g-MA were first reinforced with organoclay since the intercalation process occurs preferentially in the amorphous phase. (author)

Study of belite calcium sulfo-aluminate cement potential for zinc conditioning: From hydration to durability

International Nuclear Information System (INIS)

Berger, St.

2009-12-01

Calcium silicate cements are widely used for low- and intermediate-level radioactive waste conditioning. However, wastes produced by nuclear activities are very diverse and some of their components may chemically react with cement phases. For instance, ashes resulting from the incineration of technological wastes including neoprene and polyvinylchloride may contain substantial amounts of soluble zinc chloride. This compound is known to strongly delay or inhibit Portland cement setting. One approach to limit adverse cement-waste interactions is to select a binder showing a better compatibility with the waste while keeping cement matrix advantages (low cost, simple process, hydration with water provided by the waste...). This work thus investigates the potential of calcium sulfo-aluminate cement for zinc Zn(II) immobilization. Four aspects were considered: hydration (kinetics and products formed), properties of hydrated binders, mechanisms of zinc retention and durability of the cement pastes (based on leaching experiments and modelling). The influence of three main parameters was assessed: the gypsum content of the cement, the concentration of ZnCl 2 and the thermal evolution at early age. It follows that materials based on a calcium sulfo-aluminate cement containing 20% gypsum are interesting candidates for zinc Zn(II) stabilization/solidification: there is no delay in hydration, mineralogy of the hydrated phases is slightly dependent on thermal history, mechanical strength is high, dimensional changes are limited and zinc Zn(II) is well immobilized, even if the cement paste is leached by pure water during a long period (90 d). (author)

Phosphorus release from phosphate rock and iron phosphate by low-molecular-weight organic acids.

Science.gov (United States)

Xu, Ren-kou; Zhu, Yong-guan; Chittleborough, David

2004-01-01

Low-molecular-weight(LMW) organic acids widely exist in soils, particularly in the rhizosphere. A series of batch experiments were carried out to investigate the phosphorus release from rock phosphate and iron phosphate by low-molecular-weight organic acids. Results showed that citric acid had the highest capacity to solubilize P from both rock and iron phosphate. P solubilization from rock phosphate and iron phosphate resulted in net proton consumption. P release from rock phosphate was positively correlated with the pKa values. P release from iron phosphate was positively correlated with Fe-organic acid stability constants except for aromatic acids, but was notcorrelated with pKa. Increase in the concentrations of organic acids enhanced P solubilization from both rock and iron phosphate almost linearly. Addition of phenolic compounds further increased the P release from iron phosphate. Initial solution pH had much more substantial effect on P release from rock phosphate than from iron phosphate.

Determinación de la resistencia del hornnigón en viguetas fabricadas con cemento aluminóso

Directory of Open Access Journals (Sweden)

de la Fuente Sánchez, Antonio

1993-03-01

Full Text Available Not Available.

La resistencia de los hormigones en viguetas de cemento aluminóso es uno de los parámetros más solicitados a los laboratorios de control. La dificultad de su determinación estriba en la gran cantidad de armaduras que suelen llevar las alas de la vigueta, siendo el alma la única zona de la que pueden extraerse muestras de hormigón.

Effects of the blended fibroin/aloe gel film on wound healing in streptozotocin-induced diabetic rats

International Nuclear Information System (INIS)

Inpanya, Paichit; Viyoch, Jarupa; Faikrua, Atchariya; Ounaroon, Anan; Sittichokechaiwut, Anuphan

2012-01-01

Delayed healing remains a major clinical problem and here we have sought to develop an improved dressing film comprising 1.95% w/v fibroin and 0.05% w/v aloe gel extract. The tensile strength of dry film was 21.1 ± 0.5 MPa and broke at 1.1 ± 0.2% elongation; corresponding values for wet film were 18.3 ± 1.3 MPa and 1.9 ± 0.1%. The film maintained its shape upon water immersion and the swelling ratio of the dry film was 0.8 ± 0.1 while the water uptake was 43.7 ± 2.6%. After 28 days of incubation in phosphate buffered saline (1 M, pH 7.4, 37 °C), the weight of film was reduced by 6.7 ± 1.1% and the tensile strength and elongation at breaking point (dry state) were 15.4 ± 0.6 MPa and 1.5 ± 0.2%, respectively. Compared to aloe-free fibroin film (2.0% fibroin extract only), the blended film enhanced the attachment and proliferation of skin fibroblasts. The bFGF immunofluorescence of fibroblasts cultured on the blended film appeared greater than those cultured on tissue culture plate or on aloe-free fibroin film while α-smooth muscle actin was maintained. In streptozotocin-induced diabetic rats, the wounds dressed with the blended film were smaller (p <0.05) by day 7 after wounding, compared to untreated diabetic wounds. Histology of repaired diabetic wounds showed the fibroblast distribution and collagen fiber organization to be similar to wounds in normal rats, and this was matched by enhanced hydroxyproline content. Thus, such accelerated wound healing by the blended fibroin/aloe gel films may find application in treatment of diabetic non-healing skin ulcers. (paper)

Metamorphic history and age of aluminous gneisses of the Belomorian belt of the Baltic shield

International Nuclear Information System (INIS)

Bibikova, E.V.; Borisova, E.Yu.; Makarov, V.A.; Drugova, G.M.

1997-01-01

Metamorphic conditions and age are determined for the early metamorphic stage of aluminous gneisses in the Chupa nappe in the Belomorian Mobile Belt. The granulite-facies metamorphic conditions during Late Archean time are determined based on the composition of garnet and biotie from the metapelites. The early metamorphic stage was dated at 2860 ± 30 Ma based on the U-Pb systematics of granulitic zircon from the metapelites. The U-Pb isotopic system of the zircon was strongly affected by Svecogennian metamorphism (at 1750 Ma). The geodynamic evolution of the Belomorian Mobile Belt is discussed in light of the data of this work

Synthesis of calcium aluminate with silicon addition for application in biomaterials

International Nuclear Information System (INIS)

Rodrigues, P.J.; Almeida, L.H.S.; Pappen, F.G.; Ribeiro, A.S.; Cava, S.S.; Veiga, F.C.T.; Jurado, J.

2016-01-01

Ceramic materials have biocompatibility have been studied, researched and applied in various treatments such as endodontics and orthopedics. This study aims to carry out the synthesis by the polymeric precursor method for post calcium trialuminato (C3A) and with addition of 1% and 5% silver, them the powders were calcined in de temperature 1000°C, carried out a comparative study between them. The ceramic powders were characterized by X-ray diffraction, having a phase composition, scanning electron microscopy (SEM) associated with EDS observed grain morphology and quantity of the chemical elements. The analysis flow, pH, release of calcium ions (Ca"2"+) and silver ions (Ag"+) were evaluated with the sealer MTA Fillapex result that calcium aluminate addition of silver improved the MTA Fillapex stream with the release of ions Ca"+"2, being a material that allows applications in the field of endodontics. (author)

Optical absorption and photoluminescence properties of chromium in different host glasses

Energy Technology Data Exchange (ETDEWEB)

Lachheb, R., E-mail: raouialach66@gmail.com [LaboratoireGéoressources, Matériaux, Environnement et Changements Globaux, Faculty of Sciences of Sfax, Sfax University, 3018 Sfax (Tunisia); Herrmann, A. [Otto-Schott-Institut, Jena University, Fraunhoferstraße 6, 07743 Jena (Germany); Damak, K. [LaboratoireGéoressources, Matériaux, Environnement et Changements Globaux, Faculty of Sciences of Sfax, Sfax University, 3018 Sfax (Tunisia); Rüssel, C. [Otto-Schott-Institut, Jena University, Fraunhoferstraße 6, 07743 Jena (Germany); Maâlej, R. [LaboratoireGéoressources, Matériaux, Environnement et Changements Globaux, Faculty of Sciences of Sfax, Sfax University, 3018 Sfax (Tunisia)

2017-06-15

The optical absorption, excitation and fluorescence spectra, and emission lifetimes of chromium (III) were investigated in a wide variety of oxide glasses (aluminosilicate, aluminate and phosphate). For all glasses, weak crystal field strengths were deduced from the absorption spectra. The effect of the glass matrix and the Cr{sup 3+} concentration on the fluorescence properties of Cr{sup 3+} ions were investigated. An increased fluorescence intensity of Cr{sup 3+}was found for glasses of low optical basicity, the spectral position of the Cr{sup 3+} absorption and emission, however, was hardly influenced by the glass composition. The optical absorption spectra of the chromium doped aluminosilicate and aluminate glasses showed the presence of Cr{sup VI}, while in phosphate glasses most chromium occurred as Cr{sup 3+} ions. Furthermore, for the glass with the lowest basicity, the Cr{sup 3+}concentration was optimized in order to achieve maximum fluorescence emission intensity.

Use of sodium aluminate in waste water treatment plants: wishes of saving money and innovating; Uso del aluminato sodico en las EDAR: una propuesta para innovar y economizar costes de explotacion

Energy Technology Data Exchange (ETDEWEB)

Humbert Fernandez, F.; Delgado Espinola, G.; Soler Cantalosella, M.; Dalman Martori, E.; Iranzo Blasco, C.; Sanz Torrejon, A.

2006-07-01

Most waste water treatment plants have processes to remove nutrients in order to avoid eutrophication in water receiving bodies. Regarding phosphorus removal. the most common option is chemical precipitation with ferric or aluminical precipitation with ferric or aluminium salts. We show here the successful experience carried out by the WWTP of Blanes and the company Safloc. A method ato remove phosphorus from waste water was developed by adding sodium aluminate. The use of this compound has turned out to be a sustainable way for this purpose in terms of costs, reliability and minimization of sludge production. (Author)

Polyethylene/hydrophilic polymer blends for biomedical applications.

Science.gov (United States)

Brynda, E; Houska, M; Novikova, S P; Dobrova, N B

1987-01-01

Polyethylene blends with poly(2-hydroxyethyl methacrylate) [poly(HEMA)] or poly(2,3-dihydroxypropyl methacrylate) [poly(DHPMA)] were prepared by swelling polyethylene with HEMA or 2,3-epoxypropyl methacrylate (EPMA) and by polymerization of the respective monomers. Poly(EPMA) in blends was hydrolysed to poly(DHPMA) with acetic acid. The blends had similar surface and bulk compositions. Swelling with water and surface wettability were proportional to the content of the hydrophilic component; at the same content the polyethylene/poly(DHPMA) blends appeared more hydrophilic than those of polyethylene/poly(HEMA). Thrombus formation in contact with blood examined ex vivo and in vivo was considerably slower on the blends than on unmodified polyethylene. The tests indicated optima in composition; the best biological response was achieved with the blends containing about 14% poly(HEMA) or 16% poly(DHPMA).

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation.

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

Viscoelastic properties of PLA/PCL blends compatibilized with different methods

Science.gov (United States)

Shin, Boo Young; Han, Do Hung

2017-11-01

The aim of this study was to observe changes in the viscoelastic properties of PLA/PCL (80/20) blends produced using different compatibilization methods. Reactive extrusion and high-energy radiation methods were used for blend compatibilization. Storage and loss moduli, complex viscosity, transient stress relaxation modulus, and tan δ of blends were analyzed and blend morphologies were examined. All compatibilized PLA/PCL blends had smaller dispersed particle sizes than the non-compatibilized blend, and well compatibilized blends had finer morphologies than poorly compatibilized blends. Viscoelastic properties differentiated well compatibilized and poorly compatibilized blends. Well compatibilized blends had higher storage and loss moduli and complex viscosities than those calculated by the log-additive mixing rule due to strong interfacial adhesion, whereas poorly compatibilized blends showed negative deviations due to weak interfacial adhesion. Moreover, well compatibilized blends had much slower stress relaxation than poorly compatibilized blends and didn't show tan δ plateau region caused by slippage at the interface between continuous and dispersed phases.

Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

International Nuclear Information System (INIS)

Quirino, M.R.; Oliveira, M.J.C.; Keyson, D.; Lucena, G.L.; Oliveira, J.B.L.; Gama, L.

2016-01-01

Highlights: • ZnAl_2O_4 spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT_b15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO_3)_3·9H_2O, Zn(NO_3)_2·6H_2O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl_2O_4 had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m"2 g"−"1) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

Mechanical properties of irradiated rubber-blends

International Nuclear Information System (INIS)

Nasr, G.M.; Madani, M.

2005-01-01

A study has been made on blend ratios of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) that are loaded with general purpose furnace (GPE) carbon black and irradiated at different gamma radiation doses. It was fount that the mechanical properties of such blend are highly affected by γ- irradiation dose and the composition ratios of its constituents. The elongation at break for blends was found to increase slightly with increasing NBR loafing which is mainly due to the stiffness of blending matrix formation between NR and GPF carbon black particles. The hysteresis loss, extension ratio and shape factor have been calculated for the different un-irradiated and irradiated samples

Binary blend Nanoparticles with defined morphology

International Nuclear Information System (INIS)

Ghazy, O.A.H.

2008-01-01

The word blend in linguistics means a word formed from two parts of two words. In polymer science polymer blends means polymer mixtures, a class of materials analogues to the metal alloys. Blending of polymers is a simple and economic way to create new materials meeting specific desired properties. The other alternative is to synthesize such materials eventually facing the organic chemistry design difficulties. The low entropy of mixing polymers makes the process thermodynamically unfavorable, unless there are some specific interactions between the mixed polymers. As a result, in thermal equilibrium typically a phase separation between the blend components takes place. The main challenge facing the blending of polymers is the control of the length scale of the phase separation. One of the most important applications, where the control of the phase separation is crucial for the performance is the organic solar cells. In organic solar cells a blend of an electron donating polymer and electron accepting one is formed. The dimensions of the phase separation between the two polymers should be in the range of the exciton diffusion length [1-3] (in semiconductors, exciton diffusion length is the average distance traveled by the electron-hole pair before recombination). Only under this condition the charge transfer at the interface between the two polymer layers can take place and the solar cell performs efficiently. The thin polymer blend layers for such applications are commonly deposited by spin coating from solution containing both polymers. The morphology of the thin layer prepared in this way is highly influenced by the preparation conditions such as the surface properties of the substrate, the solvent from which the blend was deposited, the temperature, and the annealing temperature [4-9]. Therefore controlling the length scale of phase separation in layers casted or spin coated from solutions is difficult and is a matter of trials and errors. Recently a novel

Parameters governing tritium extraction rates from lithiated ceramics. The case of lithium aluminate

International Nuclear Information System (INIS)

Roth, E.; Botter, F.; Briec, M.; Rasneur, B.; Roux, N.

1986-10-01

Significant discrepancies between results of authors comparing tritium extraction rates from different lithiated ceramics are found in the literature. Recent results obtained at C.E.A., principally on lithium aluminates, show that, for a given ceramic, parameters other than textural (grain size, porosity, etc...) may play a predominant role. Enhancements of extraction rates have been induced by adding MgO to the solid or H 2 and CO to the sweep gas, but other factors, probably related to the surface condition of samples, may produce even greater effects. Results of investigations of the influence of exposure to air at given partial pressures of water vapor or of CO 2 show that strict preirradiation procedures must be adopted for preparation, storage and handling of ceramic tritium breeders

Face-to-Face Activities in Blended Learning

DEFF Research Database (Denmark)

Kjærgaard, Annemette

While blended learning combines online and face-to-face teaching, research on blended learning has primarily focused on the role of technology and the opportunities it creates for engaging students. Less focus has been put on face-to-face activities in blended learning. This paper argues...... that it is not only the online activities in blended learning that provide new opportunities for rethinking pedagogy in higher education, it is also imperative to reconsider the face-to-face activities when part of the learning is provided online. Based on a review of blended learning in business and management...... education, we identify what forms of teaching and learning are suggested to take place face-to-face when other activities are moved online. We draw from the Community of Inquiry framework to analyze how face-to-face activities contribute to a blended learning pedagogy and discuss the implications...

BLENDED LEARNING STRATEGY IN TEACHER TRAINING PROGRAMS

Directory of Open Access Journals (Sweden)

Marian F. Byrka

2017-12-01

Full Text Available The article examines the implementation of blended learning strategy in teacher training programs as an innovation in online learning. The blended learning idea comes from blending elements which use online technology with more traditional face-to-face teaching in the same course. The article analyses teacher training programs offered by Chernivtsi Regional Institute of Postgraduate Pedagogical Education. Additional data were gathered through a questionnaire administered to teachers who attended training courses. The characteristics of blended learning strategy, its benefits and limitations for teacher training are supported by a review of literature. The article closes with the comparison of curriculum components (content delivery, learner activities, materials, and required competences between traditional and blended learning teacher training programs. Having obvious benefits in teacher training programs, the implementation of blended learning strategy sets some additional requirements to a learner, as well as to course instructors and lectors.

27 CFR 24.213 - Heavy bodied blending wine.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Heavy bodied blending wine..., DEPARTMENT OF THE TREASURY LIQUORS WINE Production of Other Than Standard Wine § 24.213 Heavy bodied blending wine. Heavy bodied blending wine is wine made for blending purposes from grapes or other fruit without...

Removal of phosphate from solution by adsorption and precipitation of calcium phosphate onto monohydrocalcite.

Science.gov (United States)

Yagi, Shintaro; Fukushi, Keisuke

2012-10-15

The sorption behavior and mechanism of phosphate on monohydrocalcite (CaCO(3)·H(2)O: MHC) were examined using batch sorption experiments as a function of phosphate concentrations, ionic strengths, temperatures, and reaction times. The mode of PO(4) sorption is divisible into three processes depending on the phosphate loading. At low phosphate concentrations, phosphate is removed by coprecipitation of phosphate during the transformation of MHC to calcite. The sorption mode at the low-to-moderate phosphate concentrations is most likely an adsorption process because the sorption isotherm at the conditions can be fitted reasonably with the Langmuir equation. The rapid sorption kinetics at the conditions is also consistent with the adsorption reaction. The adsorption of phosphate on MHC depends strongly on ionic strength, but slightly on temperature. The maximum adsorption capacities of MHC obtained from the regression of the experimental data to the Langmuir equation are higher than those reported for stable calcium carbonate (calcite or aragonite) in any conditions. At high phosphate concentrations, the amount of sorption deviates from the Langmuir isotherm, which can fit the low-to-moderate phosphate concentrations. Speciation-saturation analyses of the reacted solutions at the conditions indicated that the solution compositions which deviate from the Langmuir equation are supersaturated with respect to a certain calcium phosphate. The obtained calcium phosphate is most likely amorphous calcium phosphate (Ca(3)(PO(4))(2)·xH(2)O). The formation of the calcium phosphate depends strongly on ionic strength, temperature, and reaction times. The solubility of MHC is higher than calcite and aragonite because of its metastability. Therefore, the higher solubility of MHC facilitates the formation of the calcium phosphates more than with calcite and aragonite. Copyright © 2012 Elsevier Inc. All rights reserved.

[Blending powdered antineoplastic medicine in disposable ointment container].

Science.gov (United States)

Miyazaki, Yasunori; Uchino, Tomonobu; Kagawa, Yoshiyuki

2014-01-01

On dispensing powdered antineoplastic medicines, it is important to prevent cross-contamination and environmental exposure. Recently, we developed a method for blending powdered medicine in a disposable ointment container using a planetary centrifugal mixer. The disposable container prevents cross-contamination. In addition, environmental exposure associated with washing the apparatus does not arise because no blending blade is used. In this study, we aimed to confirm the uniformity of the mixture and weight loss of medicine in the blending procedure. We blended colored lactose powder with Leukerin(®) or Mablin(®) powders using the new method and the ordinary pestle and mortar method. Then, the blending state was monitored using image analysis. Blending variables, such as the blending ratio (1:9-9:1), container size (35-125 mL), and charging rate (20-50%) in the container were also investigated under the operational conditions of 500 rpm and 50 s. At a 20% charging rate in a 35 mL container, the blending precision of the mixtures was not influenced by the blending ratio, and was less than 6.08%, indicating homogeneity. With an increase in the charging rate, however, the blending precision decreased. The possible amount of both mixtures rose to about 17 g with a 20% charging rate in a 125 mL container. Furthermore, weight loss of medicines with this method was smaller than that with the pestle and mortar method, suggesting that this method is safer for pharmacists. In conclusion, we have established a precise and safe method for blending powdered medicines in pharmacies.

The Optimum Blend: Affordances and Challenges of Blended Learning For Students

Directory of Open Access Journals (Sweden)

Nuray Gedik

2012-03-01

Full Text Available The purpose of this study was to elicit students’ perceptions regarding the most facilitative and most challenging features (affordances and barriers in a blended course design. Following the phenomenological approach of qualitative inquiry, data were collected from ten undergraduate students who had experiences in a blended learning environment. Data were collected from the students’ weekly reşection papers, interviews with students, and documents, and analyzed by structurally and texturally describing the resulting experiences and perceptions. The findings of the study indicate that used together, online and face-to-face course structures offer several opportunities and challenges for students. The participating students mentioned interaction and communication opportunities, increased motivation, increased opportunities to voice their opinions, and reinforcement of learning as the affordances in the blended learning environment. The barriers included increased workload, cultural and technical barriers, and the inter-dependence of the two environments. Implications and suggestions are offered for instructors in higher education settings

The Optimum Blend: Affordances and Challenges of Blended Learning For Students

Directory of Open Access Journals (Sweden)

Nuray Gedik

2012-07-01

Full Text Available The purpose of this study was to elicit students’ perceptions regarding the most facilitative and most challenging features (affordances and barriers in a blended course design. Following the phenomenological approach of qualitative inquiry, data were collected from ten undergraduate students who had experiences in a blended learning environment. Data were collected from the students’ weekly reflection papers, interviews with students, and documents, and analyzed by structurally and texturally describing the resulting experiences and perceptions. The findings of the study indicate that used together, online and face-to-face course structures offer several opportunities and challenges for students. The participating students mentioned interaction and communication opportunities, increased motivation, increased opportunities to voice their opinions, and reinforcement of learning as the affordances in the blended learning environment. The barriers included increased workload, cultural and technical barriers, and the inter-dependence of the two environments. Implications and suggestions are offered for instructors in higher education settings.

Egg Shell and Oyster Shell Powder as Alternatives for Synthetic Phosphate: Effects on the Quality of Cooked Ground Pork Products.

Science.gov (United States)

Cho, Min Guk; Bae, Su Min; Jeong, Jong Youn

2017-01-01

This study aimed to determine the optimal ratio of natural calcium powders (oyster shell and egg shell calcium) as synthetic phosphate replacers in pork products. Ground pork samples were subjected to six treatments, as follows: control (-) (no phosphate added), control (+) (0.3% phosphate blend added), treatment 1 (0.5% oyster shell calcium powder added), treatment 2 (0.3% oyster shell calcium powder and 0.2% egg shell calcium powder added), treatment 3 (0.2% oyster shell calcium powder and 0.3% egg shell calcium powder added), and treatment 4 (0.5% egg shell calcium powder added). The addition of natural calcium powders resulted in an increase in the pH values of meat products, regardless of whether they were used individually or mixed. The highest cooking loss was observed ( p cooking loss in samples with natural calcium powder added was similar ( p >0.05) to that in the positive control samples. CIE L* values decreased as the amount of added egg shell calcium powder increased. CIE a* values were higher ( p egg shell powder (treatment 2 or 3) was effective for the improvement of textural properties of the pork products. The findings show that the combined use of 0.2% oyster shell calcium and 0.3% egg shell calcium should enable the replacement of synthetic phosphate in the production of cooked pork products with desirable qualities.

Wavelet and Blend maps for texture synthesis

OpenAIRE

Du Jin-Lian; Wang Song; Meng Xianhai

2011-01-01

blending is now a popular technology for large realtime texture synthesis .Nevertheless, creating blend map during rendering is time and computation consuming work. In this paper, we exploited a method to create a kind of blend tile which can be tile together seamlessly. Note that blend map is in fact a kind of image, which is Markov Random Field, contains multiresolution signals, while wavelet is a powerful way to process multiresolution signals, we use wavelet to process the traditional ble...

Silk fibroin/pullulan blend films: Preparation and characterization

Energy Technology Data Exchange (ETDEWEB)

Shivananda, C. S.; Rao, B. Lakshmeesha; Madhukumar, R.; Asha, S. [Department of Studies in Physics, Mangalore University, Mangalagangotri – 574 199 (India); Sarojini, B. K. [Department of Industrial Chemistry, Mangalore University, Mangalagangotri, Mangalore –574 199 (India); Somashekhar, R. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore – 570 006 (India); Sangappa, Y., E-mail: syhalabhavi@yahoo.co.in [Department of Studies in Physics, Mangalore University, Mangalagangotri – 574 199 (India); School of Material Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States)

2016-05-23

In this work silk fibroin/pullulan blend films have been prepared by solution casting method. The blend films were examined for structural, and thermal properties using X-ray diffraction (XRD), thermogravimatric (TGA) and differential scanning calorimetry (DSC) analysis. The XRD results indicate that with the introduction of pullulan, the interaction between SF and pullulan in the blend films induced the conformation transition of SF films and amorphous phase increases with increasing pullulan ratio. The thermal properties of the blend films were improved significantly in the blend films.

Correspondence Theory and Phonological Blending in French

Directory of Open Access Journals (Sweden)

Lee Scott

2014-07-01

Full Text Available Though less productive than rival word-formation processes like compounding and affixation, blending is still a rich source of neologisms in French. Despite this productivity, however, blends are often seen by scholars as unpredictable, uninteresting, or both. This analysis picks up where recent studies of blending have left off, using Correspondence Theory and a bundle of segmental constraints to deal with this phenomenon as it pertains to French. More specifically, it shows that blending is the result of a single output standing in correspondence with two or more other outputs, and that we do not need to refer to prosodic information, which is crucial in accounts of blending in languages with lexical stress like English, to account for the process in French. The analysis also differs from previous studies in that it locates blending exclusively within the phonology, leaving its morphological and semantic characteristics to be handled by other processes in the grammar.

Blended working: for whom it may (not work.

Directory of Open Access Journals (Sweden)

Nico W Van Yperen

Full Text Available Similarly to related developments such as blended learning and blended care, blended working is a pervasive and booming trend in modern societies. Blended working combines on-site and off-site working in an optimal way to improve workers' and organizations' outcomes. In this paper, we examine the degree to which workers feel that the two defining features of blended working (i.e., time-independent working and location-independent working enhance their own functioning in their jobs. Blended working, enabled through the continuing advance and improvement of high-tech ICT software, devices, and infrastructure, may be considered beneficial for workers' perceived effectiveness because it increases their job autonomy. However, because blended working may have downsides as well, it is important to know for whom blended working may (not work. As hypothesized, in a sample of 348 workers (51.7% women, representing a wide range of occupations and organizations, we found that the perceived personal effectiveness of blended working was contingent upon workers' psychological need strength. Specifically, the perceived effectiveness of both time-independent working and location-independent working was positively related to individuals' need for autonomy at work, and negatively related to their need for relatedness and need for structure at work.

Enhancement of antioxidative activity and cardiovascular protection in hamsters by camellia oil and soybean-camellia blended oil.

Science.gov (United States)

Chou, Ting-Yi; Lu, Yi-Fa; Inbaraj, Baskaran Stephen; Chen, Bing-Huei

2018-02-07

The aim of this study was to examine the effects of several vegetable oils and blended oil composed of soybean and camellia oils on blood lipid reduction and antioxidative activity. Forty male hamsters were fed an AIN-93 G diet for 1 wk, followed by dividing into five groups: control group-1 was fed a low-fat diet containing 5% oil for 6 wk, and the other four groups were fed high-fat diets with group-2 containing 14% palm oil, group-3 containing 14% camellia oil, group-4 containing 14% soybean oil, and group-5 containing 14% blended oil (8.4% soybean oil and 5.6% camellia oil) along with 0.2% cholesterol and 0.1% bile acid. High-fat diets raised serum triacylglycerol, total cholesterol, and aspartate aminotransferase in hamsters without affecting alanine aminotransferase. Compared with palm oil-containing diet, the other three high-fat diets reduced serum total cholesterol, low-density lipoprotein cholesterol, and the ratio of low-density lipoprotein to high-density lipoprotein cholesterol with an opposite trend for liver total cholesterol. However, compared with the control group, the serum high-density lipoprotein cholesterol level was raised for all four high-fat diets. The higher the degree of oil unsaturation, the higher the serum thiobarbituric acid reactive substances and the lower the liver triacylglycerol level and activities of fatty acid synthase, glucose 6-phosphate dehydrogenase, and malic enzymes. Both soybean and blended oils lowered the antioxidative activity of liver. Camellia and blended oils were more efficient than soybean oil in elevating serum high-density lipoprotein cholesterol and decreasing the ratio of low-density lipoprotein to high-density lipoprotein cholesterol in hamsters. Copyright © 2018 Elsevier Inc. All rights reserved.

Moisture sorption and thermal characteristics of polyaramide blend fabrics

OpenAIRE

Genç, Gözde; Alp, Burcu; Balköse, Devrim; Ülkü, Semra; Cireli, Aysun

2006-01-01

Four types of fabrics woven from various polyaramid fibers of Nomex and Kevlar blends were characterized by morphology, XRD, elemental analysis, thermal analysis, and moisture adsorption isotherms. The blends consisted of Polybenzimidazole/ Kevlar blend (40% FBI and 60% Kevlar®), Nomex Delta A (blend of 60% Kevlar and 40% Nomex®), Nomex Delta T (blend of 75% Nomex, 23% Kevlar, and 2% P140 antistatic fiber), and Nomex III (fabric with a 95/5 blend of Nomex and Kevlar) containing 1% steel fiber...

Phosphate Recovery From Sewage Sludge Containing Iron Phosphate

NARCIS (Netherlands)

Wilfert, P.K.

2018-01-01

The scope of this thesis was to lay the basis for a phosphate recovery technology that can be applied on sewage sludge containing iron phosphate. Such a technology should come with minimal changes to the existing sludge treatment configuration while keeping the use of chemicals or energy as small as

Using Blended Teaching to Teach Blended Learning: Lessons Learned from Pre-Service Teachers in an Instructional Methods Course

Science.gov (United States)

Shand, Kristen; Farrelly, Susan Glassett

2017-01-01

In this study, we explore the design and delivery of a blended social studies teaching methods course to examine the elements of the blended design that pre-service teachers found most constructive. In focus groups at the completion of the course, pre-service teachers were asked to reflect on their experience in the blended course, identify the…

LENRA as compatibilizer in NR/HDPE blends

International Nuclear Information System (INIS)

Dahlan Mohd; Mahathir Mohamed

2006-01-01

Polymer blends of 60/40 NR/RDPE were prepared using Brabender PL2000 Plasticorder with 60 g capacity. The blends were added with radiation-sensitive natural rubber (NR)-based compatibilizer, known as LENRA. They were irradiated with electron-beam radiation at various doses. The efficacy of the compatibilizer was monitored by measuring various properties of the blends such as physical and dynamic mechanical properties including morphological studies by electron microscopic technique. Early results show that the addition of LENRA improves the properties of the TPNR blends. (Author)

Blended learning within an undergraduate exercise physiology laboratory.

Science.gov (United States)

Elmer, Steven J; Carter, Kathryn R; Armga, Austin J; Carter, Jason R

2016-03-01

In physiological education, blended course formats (integration of face-to-face and online instruction) can facilitate increased student learning, performance, and satisfaction in classroom settings. There is limited evidence on the effectiveness of using blending course formats in laboratory settings. We evaluated the impact of blended learning on student performance and perceptions in an undergraduate exercise physiology laboratory. Using a randomized, crossover design, four laboratory topics were delivered in either a blended or traditional format. For blended laboratories, content was offloaded to self-paced video demonstrations (∼15 min). Laboratory section 1 (n = 16) completed blended laboratories for 1) neuromuscular power and 2) blood lactate, whereas section 2 (n = 17) completed blended laboratories for 1) maximal O2 consumption and 2) muscle electromyography. Both sections completed the same assignments (scored in a blinded manner using a standardized rubric) and practicum exams (evaluated by two independent investigators). Pre- and postcourse surveys were used to assess student perceptions. Most students (∼79%) watched videos for both blended laboratories. Assignment scores did not differ between blended and traditional laboratories (P = 0.62) or between sections (P = 0.91). Practicum scores did not differ between sections (both P > 0.05). At the end of the course, students' perceived value of the blended format increased (P learning key foundational content through video demonstrations before class greatly enhanced their learning of course material compared with a preassigned reading (94% vs. 78%, P Blended exercise physiology laboratories provided an alternative method for delivering content that was favorably perceived by students and did not compromise student performance. Copyright © 2016 The American Physiological Society.

A Phase Blending Study on Rubber Blends Based on the Solubility Preference of Curatives

NARCIS (Netherlands)

Guo, R.; Talma, Auke; Datta, Rabin; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2009-01-01

Using previously obtained data on the solubilities of curatives in SBR, EPDM and in NBR, different mixing procedures were performed on 50/50 SBR/EPDM and NBR/EPDM blends. In contrast to a previous phase-mixing study, the curatives were added to separate phases before final blending, in an attempt to

Blended Learning: An Innovative Approach

Science.gov (United States)

Lalima; Dangwal, Kiran Lata

2017-01-01

Blended learning is an innovative concept that embraces the advantages of both traditional teaching in the classroom and ICT supported learning including both offline learning and online learning. It has scope for collaborative learning; constructive learning and computer assisted learning (CAI). Blended learning needs rigorous efforts, right…

New composite materials prepared by calcium phosphate precipitation in chitosan/collagen/hyaluronic acid sponge cross-linked by EDC/NHS.

Science.gov (United States)

Kaczmarek, B; Sionkowska, A; Kozlowska, J; Osyczka, A M

2018-02-01

Nowadays, fabrication of composite materials based on biopolymers is a rising field due to potential for bone repair and tissue engineering application. Blending of different biopolymers and incorporation of inorganic particles in the blend can lead to new materials with improved physicochemical properties and biocompatibility. In this work 3D porous structures called scaffolds based on chitosan, collagen and hyaluronic acid were obtained through the lyophilization process. Scaffolds were cross-linked by EDC/NHS. Infrared spectra for the materials were made, the percentage of swelling, scaffolds porosity and density, mechanical parameters, thermal stability were studied. Moreover, the scaffolds were used as matrixes for the calcium phosphate in situ precipitation. SEM images were taken and EDX analysis was carried out for calcium and phosphorous content determination in the scaffold. In addition, the adhesion and proliferation of human osteosarcoma SaOS-2 cells was examined on obtained scaffolds. The results showed that the properties of 3D composites cross-linked by EDC/NHS were altered after the addition of 1, 2 and 5% hyaluronic acid. Mechanical parameters, thermal stability and porosity of scaffolds were improved. Moreover, calcium and phosphorous were found in each kind of scaffold. SEM images showed that the precipitation was homogeneously carried in the whole volume of samples. Attachment of SaOS-2 cells to all modified materials was better compared to unmodified control and proliferation of these cells was markedly increased on scaffolds with precipitated calcium phosphate. Obtained materials can provide the support useful in tissue engineering and regenerative medicine. Copyright © 2017 Elsevier B.V. All rights reserved.

Phosphate-a poison for humans?

Science.gov (United States)

Komaba, Hirotaka; Fukagawa, Masafumi

2016-10-01

Maintenance of phosphate balance is essential for life, and mammals have developed a sophisticated system to regulate phosphate homeostasis over the course of evolution. However, due to the dependence of phosphate elimination on the kidney, humans with decreased kidney function are likely to be in a positive phosphate balance. Phosphate excess has been well recognized as a critical factor in the pathogenesis of mineral and bone disorders associated with chronic kidney disease, but recent investigations have also uncovered toxic effects of phosphate on the cardiovascular system and the aging process. Compelling evidence also suggests that increased fibroblastic growth factor 23 and parathyroid hormone levels in response to a positive phosphate balance contribute to adverse clinical outcomes. These insights support the current practice of managing serum phosphate in patients with advanced chronic kidney disease, although definitive evidence of these effects is lacking. Given the potential toxicity of excess phosphate, the general population may also be viewed as a target for phosphate management. However, the widespread implementation of dietary phosphate intervention in the general population may not be warranted due to the limited impact of increased phosphate intake on mineral metabolism and clinical outcomes. Nonetheless, the increasing incidence of kidney disease or injury in our aging society emphasizes the potential importance of this issue. Further work is needed to more completely characterize phosphate toxicity and to establish the optimal therapeutic strategy for managing phosphate in patients with chronic kidney disease and in the general population. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

LENRA as compatibilizer in NR/HDPE blends

International Nuclear Information System (INIS)

Mahathir Mohamed; Dahlan Mohd

2004-01-01

Polymer blends of 60/40 NR/HDPE were prepared using Brabender PL2000 plasticorder with 60g capacity. The blends were added with radiation sensitive natural rubber (NR)-based compatibilizer, known as LENRA. They were irradiated in air with electron beam radiation at various doses. The efficacy of the compatibilizer was monitored by measuring various properties of the blends such as physical and dynamic mechanical properties including morphological studies by electron microscopic technique. Early results show that the addition of LENRA improves the properties of the TPNR blends. (Author)

Performance evaluation of gamma irradiated SiR-EPDM blends

Energy Technology Data Exchange (ETDEWEB)

Deepalaxmi, R., E-mail: deepalaxmivaithi@gmail.com; Rajini, V.

2014-07-01

Highlights: • The effects of gamma irradiation on SiR-EPDM blend are examined. • Cross-linking reaction is dominant in blends C, D and E, due to higher EPDM content. • The tensile strength and hardness of blend E is improved by gamma irradiation. • The blend C and EPDM rich blends (D, E) are found to have superior performance. • Among C, D and E, suitable blend can be selected for a particular NPP application. - Abstract: Cable insulation materials (CIM) should perform their safety functions throughout their installed life in nuclear power plants (NPP). The CIM will be exposed to gamma irradiation at the installed locations. In order to forecast long-term performance of CIM, the short time accelerated testing was carried out. Due to its good mechanical strength, ethylene propylene diene monomer (EPDM) is widely used as CIM. Silicone rubber (SiR) is used in high temperature environments, due to its good di-electric properties/hydrophobicity. The blending of these two polymers may result in the improvement in their specific properties. This paper analyses the effects of gamma irradiation on the five different compositions (90-10; 70-30; 50-50; 30-70; 10-90) of SiR-EPDM blends. The blends were exposed to four different doses (25 Mrad, 100 Mrad, 200 Mrad and 250 Mrad) of gamma irradiation. The electrical and mechanical parameters like volume resistivity (VRY), surface resistivity (SRY), tensile strength (TS), elongation at break (EB), hardness (H) of the virgin and gamma irradiated blends were determined as per ASTM/IEC standards. The nature of degradation was investigated using Fourier transform infrared spectroscopy (FTIR). The simultaneous occurrence of cross-linking and chain scission is found to be the mechanism for ageing in SiR-EPDM blends. The electrical parameters such as volume resistivity and surface resistivity of all the blends are found to improve for all doses of gamma irradiation. To validate the influence of cross-linking reaction of the Si

Triphenyl phosphate allergy from spectacle frames

DEFF Research Database (Denmark)

Carlsen, L; Andersen, K E; Egsgaard, Helge

1986-01-01

A case of triphenyl phosphate allergy from spectacle frames is reported. Patch tests with analytical grade triphenyl phosphate, tri-m-cresyl phosphate, and tri-p-cresyl phosphate in the concentrations 5%, 0.5% and 0.05% pet. showed positive reactions to 0.05% triphenyl phosphate and 0.5% tri......-m-cresyl phosphate, but no reaction to tri-p-cresyl phosphate. Gas chromatography of the tricresyl phosphate 5% pet. patch test material supplied from Trolab showed that it contained a mixture of a wide range of triaryl phosphates, including 0.08% triphenyl phosphate which is above the threshold for detecting...

Blended Learning: A Dangerous Idea?

Science.gov (United States)

Moskal, Patsy; Dziuban, Charles; Hartman, Joel

2013-01-01

The authors make the case that implementation of a successful blended learning program requires alignment of institutional, faculty, and student goals. Reliable and robust infrastructure must be in place to support students and faculty. Continuous evaluation can effectively track the impact of blended learning on students, faculty, and the…

Empowering Learners through Blended Learning

Science.gov (United States)

Owston, Ron

2018-01-01

Blended learning appears to facilitate learner empowerment more readily than either face-to-face or fully online courses. This contention is supported by a review of literature on the affordances of blended learning that support Thomas and Velthouse's (1990) four conditions of empowerment: choice, meaningfulness, competence, and impact. Blended…

The Basics of Blended Instruction

Science.gov (United States)

Tucker, Catlin R.

2013-01-01

Even though many of teachers do not have technology-rich classrooms, the rapidly evolving education landscape increasingly requires them to incorporate technology to customize student learning. Blended learning, with its mix of technology and traditional face-to-face instruction, is a great approach. Blended learning combines classroom learning…

Investigation of barium-calcium aluminate process to manufacture and characterize impregnated thermionic cathode for power microwave devices; Investigacao do processo de obtencao de aluminatos de bario e calcio para construcao e caracterizacao de catodos termionicos impregnados para aplicacao em dispositivos de microondas de potencia

Energy Technology Data Exchange (ETDEWEB)

Higashi, Cristiane

2006-07-01

In the present work it is described the barium calcium aluminate manufacture processes employed to produce impregnated cathodes to be used in a traveling-wave tube (TWT). The cathodes were developed using a tungsten body impregnated with barium and calcium aluminate with a 5:3:2 proportion (molar). Three different processes were investigated to obtain this material: solid-state reaction, precipitation and crystallization. Thermal analysis, thermogravimetry specifically, supported to determine an adequate preparation procedure (taking into account temperature, time and pyrolysis atmosphere). It was verified that the crystallization showed a better result when compared to those investigated (solid-state reaction and precipitation techniques - formation temperature is about 1000 deg C in hydrogen atmosphere), whereas it presented the lower formation temperature (800 deg C) in oxidizing atmosphere (O{sub 2}). It was used the practical work function distribution theory (PWFD) of Miram to characterize thermionic impregnated cathode. The PWFD curves were used to characterize the barium-calcium aluminate cathode. PWFD curves shown that the aluminate cathode work function is about 2,00 eV. (author)

The Art of Blending: Benefits and Challenges of a Blended Course for Preservice Teachers

Science.gov (United States)

Shand, Kristen; Farrelly, Susan Glassett

2018-01-01

In this study, we explore the design and delivery of a blended social studies teaching methods course according to principles and core attributes of blended course design. In a survey at the end of the course, pre-service teachers were asked to reflect on their experience in the course, and identify the benefits and challenges of the blended…

Tank 21 and Tank 24 Blend and Feed Study: Blending Times, Settling Times, and Transfers

International Nuclear Information System (INIS)

Lee, S.; Leishear, R.; Poirier, M.

2012-01-01

The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks were evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 (micro)m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion ( 60 days) settling times in Tank 21.

Silk fibroin membranes from solvent-crystallized silk fibroin/gelatin blends: Effects of blend and solvent composition

Energy Technology Data Exchange (ETDEWEB)

Gil, Eun S. [Fiber and Polymer Science Program, North Carolina State University, Raleigh, NC 27695 (United States); Frankowski, David J. [Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695 (United States); Hudson, Samuel M. [Fiber and Polymer Science Program, North Carolina State University, Raleigh, NC 27695 (United States); Spontak, Richard J. [Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695 (United States) and Department of Materials Science and Engineering, North Carolina State University, Raleigh, NC 27695 (United States)]. E-mail: Rich_Spontak@ncsu.edu

2007-04-15

Protein membranes have been prepared by mixing gelatin (G) with Bombyx mori silk fibroin (SF) and using aqueous methanol (MeOH) to induce SF crystallization. Amorphous blends of these polymers appear quasi-homogeneous, as discerned from visual observation, electron microscopy and Fourier-transform infrared (FTIR) spectroscopy. Upon subsequent exposure to aqueous MeOH, SF undergoes a conformational change from random-coil to {beta}-sheet. This transformation occurs in pure SF, as well as in each of the G/SF blends, as discerned from FTIR spectroscopy and thermal calorimetry. The influence of MeOH-induced SF crystallization on structure and property development has been measured as functions of blend and solvent composition. By preserving a support scaffold above the G helix-to-coil transition temperature, the formation of crystalline SF networks in G/SF blends can be used to stabilize G-based hydrogels or generate SF membranes for biomaterial, pharmaceutical and gas-separation purposes. The present study not only examines the properties of G/SF blends before and after SF crystallization, but also establishes the foundation for future research into thermally-responsive G/SF bioconjugates.

NESDIS Blended Rain Rate (RR) Products

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The blended Rain Rate (RR) product is derived from multiple sensors/satellites. The blended products were merged from polar-orbiting and geostationary satellite...

Novel bio-based and biodegradable polymer blends

Science.gov (United States)

Yang, Shengzhe

Most plastic materials, including high performance thermoplastics and thermosets are produced entirely from petroleum-based products. The volatility of the natural oil markets and the increasing cost of petroleum have led to a push to reduce the dependence on petroleum products. Together with an increase in environmental awareness, this has promoted the use of alternative, biorenewable, environmentally-friendly products, such as biomass. The growing interest in replacing petroleum-based products by inexpensive, renewable, natural materials is important for sustainable development into the future and will have a significant impact on the polymer industry and the environment. This thesis involved characterization and development of two series of novel bio-based polymer blends, namely polyhydroxyalkanoate (PHA)/polyamide (PA) and poly(lactic acid) (PLA)/soy protein. Blends with different concentrations and compatible microstructures were prepared using twin-screw extruder. For PHA/PA blends, the poor mechanical properties of PHA improved significantly with an excellent combination of strength, stiffness and toughness by adding PA. Furthermore, the effect of blending on the viscoelastic properties has been investigated using small-amplitude oscillatory shear flow experiments as a function of blend composition and angular frequency. The elastic shear modulus (G‧) and complex viscosity of the blends increased significantly with increasing the concentration of PHA. Blending PLA with soy protein aims at reducing production cost, as well as accelerating the biodegradation rate in soil medium. In this work, the mechanical, thermal and morphological properties of the blends were investigated using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and tensile tests.

The processing of blend words in naming and sentence reading.

Science.gov (United States)

Johnson, Rebecca L; Slate, Sarah Rose; Teevan, Allison R; Juhasz, Barbara J

2018-04-01

Research exploring the processing of morphologically complex words, such as compound words, has found that they are decomposed into their constituent parts during processing. Although much is known about the processing of compound words, very little is known about the processing of lexicalised blend words, which are created from parts of two words, often with phoneme overlap (e.g., brunch). In the current study, blends were matched with non-blend words on a variety of lexical characteristics, and blend processing was examined using two tasks: a naming task and an eye-tracking task that recorded eye movements during reading. Results showed that blend words were processed more slowly than non-blend control words in both tasks. Blend words led to longer reaction times in naming and longer processing times on several eye movement measures compared to non-blend words. This was especially true for blends that were long, rated low in word familiarity, but were easily recognisable as blends.

Evaluation of non-linear blending in dual-energy computed tomography

International Nuclear Information System (INIS)

Holmes, David R.; Fletcher, Joel G.; Apel, Anja; Huprich, James E.; Siddiki, Hassan; Hough, David M.; Schmidt, Bernhard; Flohr, Thomas G.; Robb, Richard; McCollough, Cynthia; Wittmer, Michael; Eusemann, Christian

2008-01-01

Dual-energy CT scanning has significant potential for disease identification and classification. However, it dramatically increases the amount of data collected and therefore impacts the clinical workflow. One way to simplify image review is to fuse CT datasets of different tube energies into a unique blended dataset with desirable properties. A non-linear blending method based on a modified sigmoid function was compared to a standard 0.3 linear blending method. The methods were evaluated in both a liver phantom and patient study. The liver phantom contained six syringes of known CT contrast which were placed in a bovine liver. After scanning at multiple tube currents (45, 55, 65, 75, 85, 95, 105, and 115 mAs for the 140-kV tube), the datasets were blended using both methods. A contrast-to-noise (CNR) measure was calculated for each syringe. In addition, all eight scans were normalized using the effective dose and statistically compared. In the patient study, 45 dual-energy CT scans were retrospectively mixed using the 0.3 linear blending and modified sigmoid blending functions. The scans were compared visually by two radiologists. For the 15, 45, and 64 HU syringes, the non-linear blended images exhibited similar CNR to the linear blended images; however, for the 79, 116, and 145 HU syringes, the non-linear blended images consistently had a higher CNR across dose settings. The radiologists qualitatively preferred the non-linear blended images of the phantom. In the patient study, the radiologists preferred non-linear blending in 31 of 45 cases with a strong preference in bowel and liver cases. Non-linear blending of dual energy data can provide an improvement in CNR over linear blending and is accompanied by a visual preference for non-linear blended images. Further study on selection of blending parameters and lesion conspicuity in non-linear blended images is being pursued

Corrosion Resistance of Calcium Aluminate Cement Concrete Exposed to a Chloride Environment.

Science.gov (United States)

Ann, Ki Yong; Cho, Chang-Geun

2014-01-28

The present study concerns a development of calcium aluminate cement (CAC) concrete to enhance the durability against an externally chemically aggressive environment, in particular, chloride-induced corrosion. To evaluate the inhibition effect and concrete properties, CAC was partially mixed with ordinary Portland cement (OPC), ranging from 5% to 15%, as a binder. As a result, it was found that an increase in the CAC in binder resulted in a dramatic decrease in the setting time of fresh concrete. However, the compressive strength was lower, ranging about 20 MPa, while OPC indicated about 30-35 MPa at an equivalent age. When it comes to chloride transport, there was only marginal variation in the diffusivity of chloride ions. The corrosion resistance of CAC mixture was significantly enhanced: its chloride threshold level for corrosion initiation exceeded 3.0% by weight of binder, whilst OPC and CAC concrete indicated about 0.5%-1.0%.

Contribution to the study of the oxidation reaction of the carbon oxide in contact with catalysts issued from the decomposition of nickel hydro-aluminates at various temperatures

International Nuclear Information System (INIS)

Samaane, Mikhail

1966-01-01

Addressing the study of the oxidation reaction of carbon oxide which produces carbon dioxide, this research thesis reports the study of this reaction in presence of catalysts (2NiO + Al 2 O 3 , NiAl 2 O 4 and NiO + NiAl 2 O 4 ) issued from the decomposition of nickel hydro-aluminates at different temperatures. The first part describes experimental techniques and the nature of materials used in this study. The second part reports the study of the catalytic activity of the 2NiO+Al 2 O 3 catalyst during the oxidation of CO. Preliminary studies are also reported: structure and texture of nickel hydro-aluminate which is the raw material used to produce catalysts, activation of this compound to develop the catalytic activity in CO oxidation, chemisorption of CO, O 2 and CO 2 on the 2NiO+Al 2 O 3 solid, interaction of adsorbed gases at the solid surface, and kinetic study of the oxidation reaction. The third part reports the study of the catalytic activity in the oxidation reaction of CO of spinel catalysts (NiAl 2 O 4 and NiO+NiAl 2 O 4 ) obtained by calcination of nickel hydro-aluminates at high temperature. The formation of the spinel phase, the chemisorption of CO, O 2 and CO 2 on NiAl 2 O 4 , and the kinetic of the oxidation reaction are herein studied

Effect of aluminate ions on the heat of hydration of cementitious waste forms

International Nuclear Information System (INIS)

Lokken, R.O.

1993-11-01

During the hydration and setting of high-salt content liquid waste grouts, considerable heat is generated by exothermic reactions within the grout. These reactions include hydration reactions of cementitious solids and reactions between waste constituents and the solids. Adiabatic temperature rises exceeding 80 degrees C have been estimated for grouts prepared with a dry blend of 47 wt % fly ash, 47 wt % blast furnace slag, and 6 wt % type I/II Portland cement (1) Performance criteria for grout disposal specify that the temperature of the grout waste form must not exceed 90 degrees C (2) To counter the increase in temperature, inert solids were added to the ''47/47/6'' dry blend to reduce the amount of heat-generating solids, thereby decreasing the temperature rise. Based on preliminary results from adiabatic calorimetry, a dry blend consisting of 40 wt % limestone flour, 28 wt % class F fly ash, 28 wt % ground blast furnace slag, and 4 wt % type I/II Portland cement was selected for further testing

Studies on densification, mechanical, micro-structural and structure–properties relationship of magnesium aluminate spinel refractory aggregates prepared from Indian magnesite

International Nuclear Information System (INIS)

Ghosh, Chandrima; Ghosh, Arup; Haldar, Manas Kamal

2015-01-01

The present work intends to study the development of magnesium aluminate spinel aggregates from Indian magnesite in a single firing stage. The raw magnesite has been evaluated in terms of chemical analysis, differential thermal analysis, thermogravimetric analysis, infrared spectroscopy, and X-ray diffraction. The experimental batch containing Indian magnesite and calcined alumina has been sintered in the temperature range of 1550 °C–1700 °C. The sintered material has been characterized in terms of physico-chemical properties like bulk density, apparent porosity, true density, relative density and thermo-mechanical/mechanical properties like hot modulus of rupture, thermal shock resistance, cold modulus of rupture and structural properties by X-ray diffraction in terms of phase identification and evaluation of crystal structure parameters of corresponding phases by Rietveld analysis. The microstructures developed at different temperatures have been analyzed by field emission scanning electron microscope study and compositional analysis of the developed phase has been carried out by energy dispersive X-ray study. - Highlights: • The studies have been done to characterize the developed magnesium aluminate spinel. • The studies reveal correlation between refractory behavior of spinel and developed microstructures. • The studies show the values of lattice parameters of developed phases

Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

Energy Technology Data Exchange (ETDEWEB)

Quirino, M.R. [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, M.J.C. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil); Keyson, D. [Laboratory of study in Science, DME, Federal University of Paraíba, Campus I, 58051-900 João Pessoa, PB (Brazil); Lucena, G.L., E-mail: guilherme_leo1@yahoo.com.br [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, J.B.L. [Federal University of Rio Grande do Norte, UFRN, Campus I, 59078-970 Natal, RN (Brazil); Gama, L. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil)

2016-02-15

Highlights: • ZnAl{sub 2}O{sub 4} spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT{sub b}15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO{sub 3}){sub 3}·9H{sub 2}O, Zn(NO{sub 3}){sub 2}·6H{sub 2}O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl{sub 2}O{sub 4} had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m{sup 2} g{sup −1}) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

Directory of Open Access Journals (Sweden)

Lílian Estrela Borges Baldotto

2014-06-01

Full Text Available Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i to select and characterize diazotrophs able to solubilize phosphates in vitro and (ii evaluate the initial performance of the pineapple cultivars Imperial and Pérola in response to inoculation with selected bacteria in combination with rock phosphate. The experiments were conducted at Universidade Estadual do Norte Fluminense Darcy Ribeiro, in 2009. In the treatments with bacteria the leaf contents of N, P and K were higher than those of the controls, followed by an increase in plant growth. These results indicate that the combined application of diazotrophic phosphate-solubilizing bacteria Burkholderia together with Araxá rock phosphate can be used to improve the initial performance of pineapple slips.

Classifying K-12 Blended Learning

Science.gov (United States)

Staker, Heather; Horn, Michael B.

2012-01-01

The growth of online learning in the K-12 sector is occurring both remotely through virtual schools and on campuses through blended learning. In emerging fields, definitions are important because they create a shared language that enables people to talk about the new phenomena. The blended-learning taxonomy and definitions presented in this paper…

How do arbuscular mycorrhizal fungi handle phosphate? New insight into fine-tuning of phosphate metabolism.

Science.gov (United States)

Ezawa, Tatsuhiro; Saito, Katsuharu

2018-04-27

Contents Summary I. Introduction II. Foraging for phosphate III. Fine-tuning of phosphate homeostasis IV. The frontiers: phosphate translocation and export V. Conclusions and outlook Acknowledgements References SUMMARY: Arbuscular mycorrhizal fungi form symbiotic associations with most land plants and deliver mineral nutrients, in particular phosphate, to the host. Therefore, understanding the mechanisms of phosphate acquisition and delivery in the fungi is critical for full appreciation of the mutualism in this association. Here, we provide updates on physical, chemical, and biological strategies of the fungi for phosphate acquisition, including interactions with phosphate-solubilizing bacteria, and those on the regulatory mechanisms of phosphate homeostasis based on resurveys of published genome sequences and a transcriptome with reference to the latest findings in a model fungus. For the mechanisms underlying phosphate translocation and export to the host, which are major research frontiers in this field, not only recent advances but also testable hypotheses are proposed. Lastly, we briefly discuss applicability of the latest tools to gene silencing in the fungi, which will be breakthrough techniques for comprehensive understanding of the molecular basis of fungal phosphate metabolism. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

Radiation crosslinking of polymer blends

International Nuclear Information System (INIS)

Spenadel, L.

1979-01-01

Rocked by the one-two punch of rising energy costs and tougher pollution controls, a growing number of companies are looking to radiation crosslinking as a cheaper, cleaner alternative to heat and costly chemical crosslinking agents such as peroxides. With the development of larger, more powerful electron beam machines it is now possible to irradiate parts as thick as 400 mils in a single pass. Two application areas which have been investigated at our laboratory are the electron beam processing of thermoplastic elastomeric automotive parts and EPDM electrical insulation. This paper covers work carried out to develop the necessary technology base for the radiation crosslinking of ethylene propylene/polyolefin blends. Initial results indicate that EP/PE blends of electrical insulation quality cross-link quite readily when irradiated. On the other hand, EP/PP blends developed for automotive fascia require the addition of crosslinking monomers such as trimethylol propane trimethacrylate in order for crosslinking to predominate over chain scission. Crosslinking EP/PP blends improve mar resistance, flexural set and deformation at elevated temperatures. These are all key properties for automotive fascia. (author)

Radiation processing of thermoplastic starch by blending aromatic additives: Effect of blend composition and radiation parameters

Science.gov (United States)

Khandal, Dhriti; Mikus, Pierre-Yves; Dole, Patrice; Coqueret, Xavier

2013-03-01

This paper reports on the effects of electron beam (EB) irradiation on poly α-1,4-glucose oligomers (maltodextrins) in the presence of water and of various aromatic additives, as model blends for gaining a better understanding at a molecular level the modifications occurring in amorphous starch-lignin blends submitted to ionizing irradiation for improving the properties of this type of bio-based thermoplastic material. A series of aromatic compounds, namely p-methoxy benzyl alcohol, benzene dimethanol, cinnamyl alcohol and some related carboxylic acids namely cinnamic acid, coumaric acid, and ferulic acid, was thus studied for assessing the ability of each additive to counteract chain scission of the polysaccharide and induce interchain covalent linkages. Gel formation in EB-irradiated blends comprising of maltodextrin was shown to be dependent on three main factors: the type of aromatic additive, presence of glycerol, and irradiation dose. The chain scission versus grafting phenomenon as a function of blend composition and dose were studied using Size Exclusion Chromatography by determining the changes in molecular weight distribution (MWD) from Refractive Index (RI) chromatograms and the presence of aromatic grafts onto the maltodextrin chains from UV chromatograms. The occurrence of crosslinking was quantified by gel fraction measurements allowing for ranking the cross-linking efficiency of the additives. When applying the method to destructurized starch blends, gel formation was also shown to be strongly affected by the moisture content of the sample submitted to irradiation. The results demonstrate the possibility to tune the reactivity of tailored blend for minimizing chain degradation and control the degree of cross-linking.

Application of chitosan/polyacrylamide nanofibres for removal of chromate and phosphate in water

Science.gov (United States)

Nthumbi, Richard M.; Catherine Ngila, J.; Moodley, Brenda; Kindness, Andrew; Petrik, Leslie

Water pollution is an intractable environmental problem in South Africa. Management of the water resource is vital in order to address the water scarcity issues. Research on remediation of contaminated water has focused mainly on the removal of heavy metals such as Pb, Cd, Zn, Hg and Cu and neglected other inorganic pollutants. In this work we focus on the removal of anions, namely chromate and phosphate. Chromium is extensively used in the textile, leather and metallurgy industries and contaminates surface water and groundwater when inadequately treated industrial effluents are discharged. Chromium has been associated with irregular sugar metabolism, nosebleeds and ulcers, and it is also carcinogenic. The phosphate ion is an essential micronutrient responsible for healthy plant growth. However, excess phosphate intake stimulates rapid growth of photosynthetic algae and cyanobacteria, resulting in eutrophication. This phenomenon (algal bloom) causes other organisms to die due to reduced oxygen in the water. In order to offer remediation measures, this study reports the use of electrospun nanofibres for the removal of chromate and phosphate anions. Adsorption experiments were carried out using nanofibres electrospun from chitosan and polyacrylamide polymer blends, cross-linked with glutaraldehyde. Quantification of chromium was done using ICP-OES while UV-Vis spectrophotometry was used for the determination of phosphates. Batch adsorption experiments were done to determine optimum adsorption parameters such as pH, contact time, temperature and initial analyte concentration. Removal of the ions using a flow-adsorption technique through a micro-column was performed. The experimental data obtained were analysed using Langmuir and Freundlich models to study the adsorption mechanisms. The nanofibres had an adsorption capacity for Cr(VI) and PO43- of 0.26 mg g-1 and 392 mg g-1, respectively, and removal efficiencies of 93% and 97.4%, in the same order, in synthetic water

Formulation of single super phosphate fertilizer from rock phosphate of Hazara, Pakistan

Directory of Open Access Journals (Sweden)

Matiullah Khan

2012-05-01

Full Text Available Phosphorus deficiency is wide spread in soils of Pakistan. It is imperative to explore the potential and economics of indigenous Hazara rock phosphate for preparation of single super phosphate fertilizer. For the subject study rock phosphate was collected from Hazara area ground at 160 mesh level with 26% total P2O5 content for manual preparation of single super phosphate fertilizer. The rock phosphate was treated with various concentrations of sulfuric acid (98.9%, diluted or pure in the field. The treatments comprised of 20 and 35% pure acid and diluted with acid-water ratios of 1:5, 1:2, 1:1 and 2:1 v/v for acidulation at the rate of 60 liters 100 kg-1 rock phosphate. The amount was prior calculated in the laboratory for complete wetting of rock phosphate. A quantity of 150 kg rock phosphate was taken as treatment. The respective amount of acid was applied with the spray pump of stainless steel or poured with bucket. After proper processing, chemical analysis of the products showed a range of available P2O5 content from 9.56 to 19.24% depending upon the amount of acid and its dilution. The results reveal at that 1:1 dilutions gave the highest P2O5 content (19.24%, lowest free acid (6 % and 32% weight increase. The application of acid beyond or below this combination either pure or diluted gave hygroscopic product and higher free acids. The cost incurred upon the manual processing was almost half the prevailing rates in the market. These results lead to conclude that application of sulfuric acid at the rate of 60 liters 100 kg-1 with the dilution of 50% (v/v can yield better kind of SSP from Hazara rock phosphate at lower prices.

Characterization of polycaprolactone and starch blends for potential ...

African Journals Online (AJOL)

Thermally blending starch and polycaprolactone with the compatibilizer methylenediphenyl diisocyanate (MDI) distributed in the polyester phase had been previously confirmed to enhance the mechanical properties and interface between the two phases of the blends. In this study, blends of polycaprolactone with various ...

Blending effects on coal burnout and NO emissions

Energy Technology Data Exchange (ETDEWEB)

B. Arias; R. Backreedy; A. Arenillas; J.M. Jones; F. Rubiera; M. Pourkashanian; A. Williams; J.J. Pis [Instituto Nacional del Carbon, CSIC Oviedo (Spain)

2003-07-01

In this work, the combustion behaviour of individual coals of different rank and their blends was evaluated. The study was focused on burnout and NO emissions during blend combustion. Preliminary combustion tests of the coals and their blends were carried out in a thermogravimetric analyser (TGA). Some characteristic temperatures were obtained to evaluate the combustibility of the samples. These temperatures indicate an improvement in the combustibility of the less reactive coal when it is blended. An entrained flow reactor (EFR) was employed to study the behaviour of the samples at high heating rates and short residence times. Burnout and NO emissions were measured during EFR combustion tests. In some blends the results can be predicted from the weighted average of the values of the individual coals. However, other blends show an increase, from the averaged values, in burnout and especially in NO emissions. 14 refs., 10 figs., 3 tabs.

BLENDED LEARNING COURSE FOR FUTURE PRIMARY SCHOOL TEACHERS IMPLEMENTATION

Directory of Open Access Journals (Sweden)

Vira V. Kotkova

2017-09-01

Full Text Available Ukrainian and foreign scientists’ views on the essence of blended learning are analyzed in the article. The author's definition of a blended learning course is presented. The process of such course designing is described according to target, motivational, substantive, operational and diagnostic components. Both the structure of the blended learning course implementation as well as students’ educational-cognitive activity distribution between classroom learning and distance course are shown. The problems for students, teachers, and educational institutions of blended courses effective implementation are summarized. Students’ academic performance of three years study is analyzed. The results of students’ questioning to determine their perception of blended learning course are described according to the following categories: the effectiveness of blended course, evaluation objectivity, motivation to study, the use of plagiarism in studies, understanding of blended learning course.

Morphology development in immiscible polymer blends

NARCIS (Netherlands)

Cardinaels, R.M.; Moldenaers, P.; Guo, Qipeng

This chapter discusses the morphology development of immiscible binary polymer blends. It first describes morphology development in droplet-matrix structures, the dynamics of fibrillar structures and cocontinuous structures. The chapter then considers binary immiscible polymer blends, such systems

Integrated assessment of the phosphate industry

International Nuclear Information System (INIS)

Ryan, M.T.; Cotter, S.J.

1980-05-01

The phosphate industry in the United States includes three major activities, namely, mining and milling of phosphate rock, phosphate product manufacture, and phosphate product use. Phosphatic materials contain uranium, thorium, and their decay products in greater than background amounts. This assessment of the radiological impacts associated with the redistribution of radioactive components of phosphate materials may provide insight into the effects of uranium extraction from phosphate materials for use in the nuclear fuel cycle

Synthesis of geopolymer from biomass-coal ash blends

Science.gov (United States)

Samadhi, Tjokorde Walmiki; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Fernando, Muhammad Rizki; Purbasari, Aprilina

2017-09-01

Geopolymer is an environmentally attractive Portland cement substitute, owing to its lower carbon footprint and its ability to consume various aluminosilicate waste materials as its precursors. This work describes the development of geopolymer formulation based on biomass-coal ash blends, which is predicted to be the prevalent type of waste when biomass-based thermal energy production becomes mainstream in Indonesia. The ash blends contain an ASTM Class F coal fly ash (FA), rice husk ash (RHA), and coconut shell ash (CSA). A mixture of Na2SiO3 and concentrated KOH is used as the activator solution. A preliminary experiment identified the appropriate activator/ash mass ratio to be 2.0, while the activator Na2SiO3/KOH ratio varies from 0.8 to 2.0 with increasing ash blend Si/Al ratio. Both non-blended FA and CSA are able to produce geopolymer mortars with 7-day compressive strength exceeding the Indonesian national SNI 15-2049-2004 standard minimum value of 2.0 MPa stipulated for Portland cement mortars. Ash blends have to be formulated with a maximum RHA content of approximately 50 %-mass to yield satisfactory 7-day strength. No optimum ash blend composition is identified within the simplex ternary ash blend compositional region. The strength decreases with Si/Al ratio of the ash blends due to increasing amount of unreacted silicate raw materials at the end of the geopolymer hardening period. Overall, it is confirmed that CSA and blended RHA are feasible raw materials for geopolymer production..

Enzymatic degradation of polycaprolactone–gelatin blend

International Nuclear Information System (INIS)

Banerjee, Aditi; Chatterjee, Kaushik; Madras, Giridhar

2015-01-01

Blends of polycaprolactone (PCL), a synthetic polymer and gelatin, natural polymer offer a optimal combination of strength, water wettability and cytocompatibility for use as a resorbable biomaterial. The enzymatic degradation of PCL, gelatin and PCL–gelatin blended films was studied in the presence of lipase (Novozym 435, immobilized) and lysozyme. Novozym 435 degraded the PCL films whereas lysozyme degraded the gelatin. Though Novozym 435 and lysozyme individually could degrade PCL–gelatin blended films, the combination of these enzymes showed the highest degradation of these blended films. Moreover, the enzymatic degradation was much faster when fresh enzymes were added at regular intervals. The changes in physico-chemical properties of polymer films due to degradation were studied by scanning electron microscopy, Fourier transform infrared spectroscopy and differential scanning calorimetry. These results have important implications for designing resorbable biomedical implants. (paper)

Role of Phosphate Transport System Component PstB1 in Phosphate Internalization by Nostoc punctiforme.

Science.gov (United States)

Hudek, L; Premachandra, D; Webster, W A J; Bräu, L

2016-11-01

In bacteria, limited phosphate availability promotes the synthesis of active uptake systems, such as the Pst phosphate transport system. To understand the mechanisms that facilitate phosphate accumulation in the cyanobacterium Nostoc punctiforme, phosphate transport systems were identified, revealing a redundancy of Pst phosphate uptake systems that exists across three distinct operons. Four separate PstB system components were identified. pstB1 was determined to be a suitable target for creating phenotypic mutations that could result in the accumulation of excessive levels of phosphate through its overexpression or in a reduction of the capacity to accumulate phosphate through its deletion. Using quantitative real-time PCR (qPCR), it was determined that pstB1 mRNA levels increased significantly over 64 h in cells cultured in 0 mM added phosphate and decreased significantly in cells exposed to high (12.8 mM) phosphate concentrations compared to the level in cells cultured under normal (0.8 mM) conditions. Possible compensation for the loss of PstB1 was observed when pstB2, pstB3, and pstB4 mRNA levels increased, particularly in cells starved of phosphate. The overexpression of pstB1 increased phosphate uptake by N. punctiforme and was shown to functionally complement the loss of PstB in E. coli PstB knockout (PstB - ) mutants. The knockout of pstB1 in N. punctiforme did not have a significant effect on cellular phosphate accumulation or growth for the most part, which is attributed to the compensation for the loss of PstB1 by alterations in the pstB2, pstB3, and pstB4 mRNA levels. This study provides novel in vivo evidence that PstB1 plays a functional role in phosphate uptake in N. punctiforme IMPORTANCE: Cyanobacteria have been evolving over 3.5 billion years and have become highly adept at growing under limiting nutrient levels. Phosphate is crucial for the survival and prosperity of all organisms. In bacteria, limited phosphate availability promotes the

EVA reactive blending with Si–H terminated polysiloxane by carbonyl hydrosilylation reaction: From compatibilised blends to crosslinking networks

International Nuclear Information System (INIS)

Bonnet, J.; Bounor-Legaré, V.; Alcouffe, P.; Cassagnau, P.

2012-01-01

A new and original method based on carbonyl hydrosilylation was developed to prepare ethylene-vinyl acetate (EVA)/polysiloxane polymer blends. This focused on the addition of hydrogenosilane groups (SiH) from polysiloxane to the carbonyl groups of EVA. The influence of the nature of the polysiloxane on blend properties was investigated by rheology and scanning electron microscopy. Mixing of a low viscosity polysiloxane with a high viscosity EVA matrix produced a two-phase morphology. The occurrence of the hydrosilylation reaction at the EVA/polysiloxane interface promoted a homogenisation of the blend depending on the molar ratio SiH/vinyl acetate groups, [SiH]/[VA], and the viscosity ratio of the blend. Two distinct behaviours were observed. The formation of a crosslinked network under shear was obtained for a low viscosity ratio between polysiloxane and EVA (λ polysiloxane/EVA = 4.0 × 10 −6 ) with a high concentration of SiH groups ([SiH]/[VA] = 0.5), while the formation of a compatibilised blend was observed for high molar mass polysiloxanes (Mn > 15,000 g mol −1 ) with a low concentration of SiH ([SiH]/[VA] −3 ). -- Highlights: ► Carbonyl hydrosilylation reaction was found to enhance EVA/polysiloxane immiscible blends. ► EVA crosslinking was obtained with a low molar mass polysiloxane. ► EVA compatibilisation was obtained with a high molar mass polysiloxane. ► Shear rate was found to improve the hydrosilylation reaction at the interface. ► A two-phase morphology of the blends was observed after reaction with fine polysiloxane nodules.

BioBlend.objects: metacomputing with Galaxy.

Science.gov (United States)

Leo, Simone; Pireddu, Luca; Cuccuru, Gianmauro; Lianas, Luca; Soranzo, Nicola; Afgan, Enis; Zanetti, Gianluigi

2014-10-01

BioBlend.objects is a new component of the BioBlend package, adding an object-oriented interface for the Galaxy REST-based application programming interface. It improves support for metacomputing on Galaxy entities by providing higher-level functionality and allowing users to more easily create programs to explore, query and create Galaxy datasets and workflows. BioBlend.objects is available online at https://github.com/afgane/bioblend. The new object-oriented API is implemented by the galaxy/objects subpackage. © The Author 2014. Published by Oxford University Press.

Game innovation through conceptual blending

DEFF Research Database (Denmark)

Möring, Sebastian Martin

In  this  paper  I  wish  to  apply implications of  the  Conceptual  Blending  Theory  to  computer  games.  I  will  analyze  chosen  examples  and  discuss  them  as  a  result  of  video  game  innovation  made  possible  through  "conceptual  blending."  Conceptual  blending  links  at  least.......,  Hell.  The  purpose  of  my  approach  is  not  so  much  to  validate  the  ideas  of  conceptual  blending  theory  through  another  field  of  examples  (computer  games)  but  to  name  and analyze characteristics of the mentioned games with the  help of a given method.......  integration  network  consisting  of  at  least  two  input  spaces,  a  generic  space  and  a  blended  space  as  well  as  its  governing  principles  consisting  of  composition,  completion,  and  elaboration.  With  the  help  of  these  instruments  I  analyze computer  games like  Tuper  Tario  Tros...

Effects of education on low-phosphate diet and phosphate binder intake to control serum phosphate among maintenance hemodialysis patients: A randomized controlled trial

Directory of Open Access Journals (Sweden)

Eunsoo Lim

2018-03-01

Full Text Available Background : For phosphate control, patient education is essential due to the limited clearance of phosphate by dialysis. However, well-designed randomized controlled trials about dietary and phosphate binder education have been scarce. Methods : We enrolled maintenance hemodialysis patients and randomized them into an education group (n = 48 or a control group (n = 22. We assessed the patients' drug compliance and their knowledge about the phosphate binder using a questionnaire. Results : The primary goal was to increase the number of patients who reached a calcium-phosphorus product of lower than 55. In the education group, 36 (75.0% patients achieved the primary goal, as compared with 16 (72.7% in the control group (P = 0.430. The education increased the proportion of patients who properly took the phosphate binder (22.9% vs. 3.5%, P = 0.087, but not to statistical significance. Education did not affect the amount of dietary phosphate intake per body weight (education vs. control: -1.18 ± 3.54 vs. -0.88 ± 2.04 mg/kg, P = 0.851. However, the dietary phosphate-to-protein ratio tended to be lower in the education group (-0.64 ± 2.04 vs. 0.65 ± 3.55, P = 0.193. The education on phosphate restriction affected neither the Patient-Generated Subjective Global Assessment score (0.17 ± 4.58 vs. -0.86 ± 3.86, P = 0.363 nor the level of dietary protein intake (-0.03 ± 0.33 vs. -0.09 ± 0.18, P = 0.569. Conclusion : Education did not affect the calcium-phosphate product. Education on the proper timing of phosphate binder intake and the dietary phosphate-to-protein ratio showed marginal efficacy.

A study of coal-solid waste blend reactivity

Directory of Open Access Journals (Sweden)

Nayibe Guerrero

2008-05-01

Full Text Available The Flynn-Wall-Ozawa method was used for analysing coal-solid waste blend reactivity in an oxidising atmosphere. The presence of biomass strongly affected coal combustion kinetics when the blend contained more than 30% of it. Activation energy values (evaluated by different blends were 28.7495 kJ/mol for 0% biomass, 31.3915 kJ/mol for 30% biomass, 39.0365 kJ/mol for 50% biomass, 102.431 kJ/mol for 70% biomass and 107.8075 kJ/mol for 100% biomass; these values were close to those reported in the literature. First-order kinetics correlated the data ve-ry well for the 100% coal sample and the blend having 30% biomass and 70% coal. Eighth-order kinetics were more suitable for correlating the experimental data for the 70% biomass-30% coal blend and the 100% biomass sample. Combustion was done without previous pyrolysis of the blends; however segregation of phenomena could be appre-ciated. This seems to indicate that combustion and devolatilisation are independent processes which should be taken into account when building equipment using these kinds of blend.

Production of silk sericin/silk fibroin blend nanofibers

Directory of Open Access Journals (Sweden)

Zhang Xianhua

2011-01-01

Full Text Available Abstract Silk sericin (SS/silk fibroin (SF blend nanofibers have been produced by electrospinning in a binary SS/SF trifluoroacetic acid (TFA solution system, which was prepared by mixing 20 wt.% SS TFA solution and 10 wt.% SF TFA solution to give different compositions. The diameters of the SS/SF nanofibers ranged from 33 to 837 nm, and they showed a round cross section. The surface of the SS/SF nanofibers was smooth, and the fibers possessed a bead-free structure. The average diameters of the SS/SF (75/25, 50/50, and 25/75 blend nanofibers were much thicker than that of SS and SF nanofibers. The SS/SF (100/0, 75/25, and 50/50 blend nanofibers were easily dissolved in water, while the SS/SF (25/75 and 0/100 blend nanofibers could not be completely dissolved in water. The SS/SF blend nanofibers could not be completely dissolved in methanol. The SS/SF blend nanofibers were characterized by Fourier transform infrared (FTIR spectroscopy, differential scanning calorimetry, and differential thermal analysis. FTIR showed that the SS/SF blend nanofibers possessed a random coil conformation and ß-sheet structure.

Neutronic investigations on the application of lithium aluminates in the tritium breeding blanket of future fusion reactors

International Nuclear Information System (INIS)

Mohsin, A.

1981-02-01

A survey is given about the state of development work at the blanket. It shows that present designs aim at a fusion reactor with low tritium inventory. This aim can be achieved with a solid blanket. In this paper this concept is described and the selection of appropriate materials for the solid blanket is discussed. The lithium aluminates turned out to be the most suitable materials. Comparing the different lithium aluminates the compounds Li 5 AlO 4 and LiAlO 2 proved to be the most favourable. The improvement of the breeding ratio when using lead as neutron multiplier was investigated. Employing, for example, a lead zone of 15 cm thickness in front of a 60 cm thick breeding zone, the tritium breeding ratio is raised to 1.65 for Li 5 Al 4 and to 1.48 for LiAlO 2 - The originally higher breeding ratio of the Li 5 AlO 4 in contrary to the LiAlO 2 is compensated hereby. By this LiAlO 2 becomes a very interesting material for a solid blanket since it furthermore exhibits a higher melting point and higher phase transition temperature. For experimental check of the nuclear data of this material and the computational techniques used, a test model was designed and built. This blanket model was used for measuring the space-dependent tritium production rate, which could be compared to corresponding computations. The assembly was made of a lead zone as neutron multiplier, LiAlO 2 as breeding material, and polyethylene as neutron reflector. (orig.) [de

Blended Learning as Transformational Institutional Learning

Science.gov (United States)

VanDerLinden, Kim

2014-01-01

This chapter reviews institutional approaches to blended learning and the ways in which institutions support faculty in the intentional redesign of courses to produce optimal learning. The chapter positions blended learning as a strategic opportunity to engage in organizational learning.

The effects of re-firing process under oxidizing atmosphere and temperatures on the properties of strontium aluminate phosphors

International Nuclear Information System (INIS)

Karacaoglu, Erkul; Karasu, Bekir

2013-01-01

Graphical abstract: The comparative emission spectra of standard and re-fired Phosphor A under oxidizing atmosphere at various temperatures. The colour of Phosphor A re-fired at higher temperatures above 900 °C shifted from yellowish-green to bluish-green in the dark. But, the bluish-green emission could only be seen when it was exposed to UV and disappeared as soon as the light source was removed. Moreover, the emission intensities decreased as the re-firing temperatures increased. This could be attributed to the oxidation of Eu 2+ during the re-firing process. It is well known fact from the literature that the reduction of Eu 3+ to Eu 2+ in appropriate host materials needs an annealing process in a reducing atmosphere such as H 2 , H 2 /N 2 mixture or CO. Up to now, the reduction phenomena of Eu 3+ → Eu 2+ in air have been found in phosphates (Ba 3 (PO 4 ) 2 :Eu), sulphates (BaSO 4 :Eu), borates (SrB 4 O 7 :Eu, SrB 6 O 10 :Eu and BaB 8 O 13 :Eu) and aluminates (Sr 4 Al 14 O 25 :Eu). Interestingly, an apparent blue shift in the phosphorescence spectrum was observed in the samples re-fired at 1000 °C and above, indicating a minimal effect on the oxidation state or the electronic energy levels of the co-doped Dy 3+ ions, which were thought to act as long-lived hole traps resulting in long afterglow. - Highlights: • This study examines the effects re-firing at oxidizing atmosphere of photoluminescence of three different commercial SrAl 2 O 4 :Eu 2+ ,Dy 3+ -phosphors. • All the commercial SrAl 2 O 4 :Eu 2+ ,Dy 3+ -phosphors completely lost their phosphorescence after being re-fired at 1300 °C. • Oxidizing environment and re-firing temperature naturally affecting the valance of Eu 2+ may cause the basic lattice structure to be modified and also limit their applications at higher temperatures, such as third firing vetrosa décor or glaze applications in ceramic industry. • It was thought that this kind of study may be promising to provide many outcome

Blended Learning within an Undergraduate Exercise Physiology Laboratory

Science.gov (United States)

Elmer, Steven J.; Carter, Kathryn R.; Armga, Austin J.; Carter, Jason R.

2016-01-01

In physiological education, blended course formats (integration of face-to-face and online instruction) can facilitate increased student learning, performance, and satisfaction in classroom settings. There is limited evidence on the effectiveness of using blending course formats in laboratory settings. We evaluated the impact of blended learning…

Zinc phosphate conversion coatings

Science.gov (United States)

Sugama, Toshifumi

1997-01-01

Zinc phosphate conversion coatings for producing metals which exhibit enhanced corrosion prevention characteristics are prepared by the addition of a transition-metal-compound promoter comprising a manganese, iron, cobalt, nickel, or copper compound and an electrolyte such as polyacrylic acid, polymethacrylic acid, polyitaconic acid and poly-L-glutamic acid to a phosphating solution. These coatings are further improved by the incorporation of Fe ions. Thermal treatment of zinc phosphate coatings to generate .alpha.-phase anhydrous zinc phosphate improves the corrosion prevention qualities of the resulting coated metal.

Potential Application of ENR/EPDM Blends

Directory of Open Access Journals (Sweden)

B.L. Chan

2017-06-01

Full Text Available Since the process and conversion of natural rubber into epoxidized natural rubber (ENR was discovered and patented by I. R. Gelling of the Malaysian Rubber Product Research Association  (or now known as the Tun Razak laboratory, Brickendonbury, Hertford, in the United Kingdom, there are more than 10 000 technical and technological papers cited in the internet. Information on ENR is available, not only in the the English language but also other languages like Chinese, Malay, French, Thai and even German languages are used. NR is the most versatile and reactive rubber/elastomer. It is an advanced natural rubber which could be potentially used as a starting material for the development of other rubbers, modifie elastomers, for grafting, plastic-based materials and also thermoplastic rubbers. Its reactivity is dependent on its epoxy groups, the opening of its ring structure, and also the subsequent structures of carboxylic groups and the in-situ side-chains “carbon – carbon” double bonds (> C = C <. In some instances, up to 65% epoxidation of NR is possible and achieved for more oil resistance. For these reasons, there are many new and advanced materials which have been formed and developed in the last two decades. Among them, some of the recent research work is listed here. Apart from studies of compounding the ENR itself and its potential uses, there are many rubber-rubber blends and ENR rubber-plastics blends, some of the studies cited are “uses of new and advanced chemicals”  and synthetic rubbers:  ENR/NBR, ENR/PVC, ENR/polylactic acid blends, ENR/copolyester blends, ENR/Copolyamide Blends, ENR/poly (vinylidene fluorideblends, ENR/Carbon Nanotubes with co-agent Trimethylol Propane Triacrylate, ENR /recycled silicon materials, and ENR/copolymer of n-butyl acrylate/butyl methacrylate “grafted”. Each of these blends has its own characteristics in terms of processing, enhancement of processing like safety, scorch, oil and water

Teaching of anatomical sciences: A blended learning approach.

Science.gov (United States)

Khalil, Mohammed K; Abdel Meguid, Eiman M; Elkhider, Ihsan A

2018-04-01

Blended learning is the integration of different learning approaches, new technologies, and activities that combine traditional face-to-face teaching methods with authentic online methodologies. Although advances in educational technology have helped to expand the selection of different pedagogies, the teaching of anatomical sciences has been challenged by implementation difficulties and other limitations. These challenges are reported to include lack of time, costs, and lack of qualified teachers. Easy access to online information and advances in technology make it possible to resolve these limitations by adopting blended learning approaches. Blended learning strategies have been shown to improve students' academic performance, motivation, attitude, and satisfaction, and to provide convenient and flexible learning. Implementation of blended learning strategies has also proved cost effective. This article provides a theoretical foundation for blended learning and proposes a validated framework for the design of blended learning activities in the teaching and learning of anatomical sciences. Clin. Anat. 31:323-329, 2018. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Study of the ultrasonic waves action on the preparation of calcium aluminates cements

International Nuclear Information System (INIS)

Lourenco, R.R.; Exposito, C.C.D.; Rodrigues, J.A.

2009-01-01

Calcium aluminates cements were prepared through a route that uses the sonochemical process. In this process, calcia and alumina in an aqueous suspension are put under an ultrasonic bath during some time. After that, the water is evaporated and the material is heat treated. In this work, the action of ultrasonic waves were studied on initials molar compositions calcia:alumina of 1:1. It was also verified the influence of the water on the reactivity of initial solids. SEM and X-ray diffraction were used to characterize the obtained materials. In addition, mechanical strength of the products was evaluated through splitting tensile tests. The X-ray diffractograms showed that the presence of the water was enough to form hydrated compounds. However the material subjected to the sonochemical process presented the highest mechanical strength, indicating the potential of this route of synthesis. (author)

The effect of Y2O3 addition on thermal shock behavior of magnesium aluminate spinel

Directory of Open Access Journals (Sweden)

Pošarac Milica

2009-01-01

Full Text Available The effect of yttria additive on the thermal shock behavior of magnesium aluminate spinel has been investigated. As a starting material we used spinel (MgAl2O4 obtained by the modified glycine nitrate procedure (MGNP. Sintered products were characterized in terms of phase analysis, densities, thermal shock, monitoring the damaged surface area in the refractory specimen during thermal shock and ultrasonic determination of the Dynamic Young modulus of elasticity. It was found that a new phase between yttria and alumina is formed, which improved thermal shock properties of the spinel refractories. Also densification of samples is enhanced by yttria addition.

Polymer blends of polylactic acid (PLA) and polybutylene succinate-adipate

Science.gov (United States)

Ma, Wenguang

A series of blends consisting of polylactic acid (PLA) and aliphatic succinate polyester (BionolleRTM #3000) had been prepared and investigated. The results of mechanical property investigations showed that using 20 wt% Bionolle#3000 can significantly increase the toughness of PLA. BionolleRTM #3000 also reduces the physical aging rate of PLA so blends remain tough longer. Conversely, the stiffness of BionolleRTM #3000 can be significantly increased by blending in PLA. DMA and DSC results show that PLA/BionolleRTM 3000 blends are not thermodynamically miscible, but are compatible blends. Studies have also been performed to determine the amount and rate of aerobic biodegradation of PLA/aliphatic succinate polyester blends in biologically active composting, enzymatic, and soil environments. The changes in molecular weight, molecular structure and thermal properties in the composting environment were also studied by GPC, NMR and DSC analyses. The research results showed BionolleRTM #3000 had a high degradation rate, while PLA had a low degradation rate. PLA/BionolleRTM #3000 blends had moderate degradation rates that increased with BionolleRTM #3000 content. The melt flow behavior of PLA/BionolleRTM #3000 blends has been studied by capillary rheometry. The relationship of the blends' viscosity with their composition, shear stress, shear rate, and temperature has been investigated. Power law index and activation energy of PLA, BionolleRTM #3000 and their blends have been calculated. The experimental and theoretical data can let us understand the processability of PLA/BionolleRTM #3000 blends. A scanning electron microscope (SEM) was used to investigate the morphological structure of the PLA/BionolleRTM #3000 blends. Micrographs of the samples made from different methods (blown film, extrudate and compression molding sheet) were taken; their differences in morphology were compared. For comparison, the micrographs of blend PLA/BionolleRTM #6000 was also studied. The

Finding a balance in dimensions of blended learning

NARCIS (Netherlands)

Verkroost, M.; Meijerink, L.; Lintsen, H.W.; Veen, W.

2008-01-01

This article is a formative evaluation of a course in which a blended learning environment was created and a good balance in dimensions of blended learning was sought. Blended learning is defined as the total mix of pedagogical methods, using a combination of different learning strategies, both with

Synthesis optimization of calcium aluminate cement phases for biomedical applications

International Nuclear Information System (INIS)

Andrade, T.L.; Santos, G.L.; Oliveira, I.R.; Pandolfelli, V.C.

2011-01-01

Calcium aluminate cement (CAC) has been studied as a potential material for applications in the areas of health such as, endodontics and bone reconstruction. These studies have been based on commercial products consisting of a mixture of phases. Improvements can be attained by investigating the synthesis routes of CAC aiming the proper balance between the phases and the control of impurities that may impair its performance for biomedical applications. Thus, the aim of this work was to study the CAC synthesis routes in the Al 2 O 3 -CaCO 3 and Al 2 O 3 -CaO systems, as well as the phase characterization attained by means of X ray analysis. The Al 2 O 3 -CaO route enabled the production of the target phases (CA, CA 2 , C 3 A and C 12 A 7 ) with a higher purity compared to the Al2O3-CaCO3 one. As a result the particular properties of these phases can be evaluated to define a more suitable composition that results in better properties for an endodontic cement and other applications. (author)

NOx emissions and combustibility characteristics of coal blends

Energy Technology Data Exchange (ETDEWEB)

Rubiera, F.; Arenillas, A.; Arias, B.; Pis, J.J. [CSIC, Instituto Nacional del Carbon, Oviedo (Spain). Dept. of Energy and Environment

2001-07-01

In this work, a series of coals with different origin and rank were blended and several aspects of the resultant blends were studied. This included determination of the grindability of individual coals and blends by means of the Hardgrove Grindability Index (HGI), and temperature programmed combustion test, which were carried out in a thermogravimetric analyser (TG) coupled to a quadruple mass spectrometer (MS) for evolved gas analysis. Special attention was paid to the combustibility parameters and the NO emissions during blends combustion. It was found that while some coal blends present interaction between the individual coals, others do not. This behaviour was assumed to be due to the differences in coal structure and functional groups composition. 18 refs., 11 figs., 2 tabs.

On The compatibility and dynamic vulcanization of Pom/Nbr blends

International Nuclear Information System (INIS)

Mortezaee, M.; Naveed Family, M.H.; Mehrabzadeh, M.

2001-01-01

Polymer blends based on polyacetal butadiene rubber were prepared by melt blending technique. The mixing parameters such ad temperature, time and speed of mixing were varied to obtain a wide range of properties. The mixing parameters were optimized by evaluating the mechanical properties of the blend over a wide range of mixing conditions. The morphology of the blend indicated a two-phase structure. This study describes an attempt to improve the tensile strength of Pom/Nbr blends by means of compatibility and dynamic vulcanization. A commercial compatibility, maleic anhydride (Ma), has been used to control the phase morphology of the blend system. Dicumyl peroxide is used to dynamically vulcanize the Nbr elastomer in the blend. The tensile strength of the compatibility systems showed improvement. Dynamic vulcanization raises elastic recovery and tensile modulus of the blends, but the elongation at break decreases

Hemodialysis for near-fatal sodium phosphate toxicity in a child receiving sodium phosphate enemas.

Science.gov (United States)

Becknell, Brian; Smoyer, William E; O'Brien, Nicole F

2014-11-01

This study aimed to demonstrate the importance of considering hemodialysis as a treatment option in the management of sodium phosphate toxicity. This is a case report of a 4-year-old who presented to the emergency department with shock, decreased mental status, seizures, and tetany due to sodium phosphate toxicity from sodium phosphate enemas. Traditional management of hyperphosphatemia with aggressive hydration and diuretics was insufficient to reverse the hemodynamic and neurological abnormalities in this child. This is the first report of the use of hemodialysis in a child without preexisting renal failure for the successful management of near-fatal sodium phosphate toxicity. Hemodialysis can safely be used as an adjunctive therapy in sodium phosphate toxicity to rapidly reduce serum phosphate levels and increase serum calcium levels in children not responding to conventional management.

Phosphate transporter mediated lipid accumulation in Saccharomyces cerevisiae under phosphate starvation conditions.

Science.gov (United States)

James, Antoni W; Nachiappan, Vasanthi

2014-01-01

In the current study, when phosphate transporters pho88 and pho86 were knocked out they resulted in significant accumulation (84% and 43%) of triacylglycerol (TAG) during phosphate starvation. However in the presence of phosphate, TAG accumulation was only around 45% in both pho88 and pho86 mutant cells. These observations were confirmed by radio-labeling, fluorescent microscope and RT-PCR studies. The TAG synthesizing genes encoding for acyltransferases namely LRO1 and DGA1 were up regulated. This is the first report for accumulation of TAG in pho88Δ and pho86Δ cells under phosphate starvation conditions. Copyright © 2013. Published by Elsevier Ltd.

Flame retardancy mechanisms of bisphenol A bis(diphenyl phosphate) in combination with zinc borate in bisphenol A polycarbonate/acrylonitrile-butadiene-styrene blends

International Nuclear Information System (INIS)

Pawlowski, Kristin H.; Schartel, Bernhard; Fichera, Mario A.; Jaeger, Christian

2010-01-01

Bisphenol A polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) with and without bisphenol A bis(diphenyl phosphate) (BDP) and 5 wt.% zinc borate (Znb) were investigated. The pyrolysis was studied by thermogravimetry (TG), TG-FTIR and NMR, the fire behaviour with a cone calorimeter applying different heat fluxes, LOI and UL 94. Fire residues were examined with NMR. BDP affects the decomposition of PC/ABS and acts as a flame retardant in the gas and condensed phases. The addition of Znb results in an additional hydrolysis of PC. The fire behaviour is similar to PC/ABS, aside from a slightly increased LOI and a reduced peak heat release rate, both caused by borates improving the barrier properties of the char. In PC/ABS + BDP + Znb, the addition of Znb yields a borate network and amorphous phosphates. Znb also reacts with BDP to form alpha-zinc phosphate and borophosphates that suppress the original flame retardancy mechanisms of BDP. The inorganic-organic residue formed provides more effective flame retardancy, in particular at low irradiation in the cone calorimeter, and a clear synergy in LOI, whereas for more developed fires BDP + Znb become less effective than BDP in PC/ABS with respect to the total heat evolved.

Microstructure of aluminized coating on a Ni-Cr alloy after annealing treatment

International Nuclear Information System (INIS)

Huang, H.-L.; Gan Dershin

2008-01-01

The effects of annealing on the microstructure of first stage (high-Al activity pack) aluminized coating on Ni-15Cr alloy prepared by pack cementation method were analyzed by transmission electron microscope. The coating consists of a thin layer of γ'-Ni 3 Al, an interfacial zone of mixed β-NiAl and α-Cr, and a thick outer zone of β-NiAl (A layer) and mixed β-NiAl and α-Cr (B layer). Martensitic transformation was observed in the β-NiAl grains in the interfacial zone. Parallel crystallographic relationship was found at the γ/γ' interface in the substrate and the α/β interface in the interfacial zone. Cr 2 Al was found to precipitate in the β-NiAl and α-Cr grains in the B layer of the outer zone. The formation mechanisms of the coating layers, the precipitates, and the observed crystallographic relationships are discussed

Evaluation of the ignition behaviour of coals and blends

Energy Technology Data Exchange (ETDEWEB)

J. Faundez; F. Rubiera; X. Garcia; A. Arenillas; A.L. Gordon; J.J. Pis [CSIC, Instituto Nacional del Carbon, Oviedo (Spain). Department of Energy and Environment

2003-07-01

An experimental study about ignition of coals and blends was carried out by using an entrained flow reactor (EFR) with continuous feed. Seven coals of varying rank, from subbituminous to semianthracite, were tested and evolving gases (O{sub 2}, CO, CO{sub 2}, NO) were measured. The ignition temperature was evaluated from the evolution profiles of these gases, and correlated inversely to the reactivity of coals, as reflected by increasing values of ignition temperatures in the sequence subbituminous, high volatile bituminous, low volatile bituminous and semianthracite coals. Mechanism of ignition varied from an heterogeneous mechanism (for subbituminous, low volatile bituminous and semianthracite coals) to an homogeneous mechanism (for high volatile bituminous coal). Experiments with coal blends showed that if a low volatile bituminous coal is blended with a high volatile bituminous coal, the latter determines the value of the ignition temperature and ignition mechanism of the blend, when its percentage in the blend is 50% or higher. For blends of subbituminous and high volatile bituminous coals, the ignition mechanism of the blend is determined by the ignition mechanism of the coal with a higher content in the blend. 12 refs., 9 figs., 1 tab.

Luminescent characteristics of praseodymium-doped zinc aluminate powders

Energy Technology Data Exchange (ETDEWEB)

Hernandez-Perez, C.D.; Garcia-Hipolito, M.; Alvarez-Fregoso, O. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Coyoacan, DF (Mexico); Alvarez-Perez, M.A. [Facultad de Odontologia, Universidad Nacional Autonoma de Mexico, Coyoacan, DF (Mexico); Ramos-Brito, F. [Laboratorio de Materiales Optoelectronicos, DIDe, Centro de Ciencias de Sinaloa, Av. De las Americas No. 2771 Nte. Col. Villa Universidad, Culiacan, Sinaloa (Mexico); Falcony, C. [Centro de Investigaciones y Estudios Avanzados del IPN, Departamento de Fisica, Mexico, DF (Mexico)

2010-02-15

In this research, we report the cathodoluminescence (CL) and preliminary photoluminescence (PL) properties of praseodymium-doped zinc aluminate powders. ZnAl{sub 2}O{sub 4}:Pr powders were synthesized by a very simple chemical process. X-ray diffraction spectra indicated a cubic spinel crystalline structure with an average crystallite size of 15 nm. CL properties of the powders were studied as a function of the praseodymium concentration and electron-accelerating potential. In this case, all the cathodoluminescent emission spectra showed main peaks located at 494, 535, 611, 646, and 733 nm, which were associated to the electronic transitions {sup 3}P{sub 0}{yields}{sup 3}H{sub 4}, {sup 3}P{sub 0}{yields}{sup 3}H{sub 5}, {sup 3}P{sub 0}{yields}{sup 3}H{sub 6}, {sup 3}P{sub 0}{yields}{sup 3}F{sub 2}, and {sup 3}P{sub 0}{yields}{sup 3}F{sub 4} of the Pr{sup 3+} ions, respectively. A quenching of the CL, with increasing doping concentration, was observed. Also, an increment on cathodoluminescent emission intensity was observed as the accelerating voltage increased. The PL emission spectrum showed similar characteristics to those of the CL spectra. The chemical composition of the powders, as determined by energy dispersive spectroscopy, is also reported. In addition, the surface morphology characteristics of the powders are shown. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

High-Fidelity Microstructural Characterization and Performance Modeling of Aluminized Composite Propellant

International Nuclear Information System (INIS)

Kosiba, Graham D.; Wixom, Ryan R.; Oehlschlaeger, Matthew A.

2017-01-01

Image processing and stereological techniques were used to characterize the heterogeneity of composite propellant and inform a predictive burn rate model. Composite propellant samples made up of ammonium perchlorate (AP), hydroxyl-terminated polybutadiene (HTPB), and aluminum (Al) were faced with an ion mill and imaged with a scanning electron microscope (SEM) and x-ray tomography (micro-CT). Properties of both the bulk and individual components of the composite propellant were determined from a variety of image processing tools. An algebraic model, based on the improved Beckstead-Derr-Price model developed by Cohen and Strand, was used to predict the steady-state burning of the aluminized composite propellant. In the presented model the presence of aluminum particles within the propellant was introduced. The thermal effects of aluminum particles are accounted for at the solid-gas propellant surface interface and aluminum combustion is considered in the gas phase using a single global reaction. In conclusion, properties derived from image processing were used directly as model inputs, leading to a sample-specific predictive combustion model.

21 CFR 137.175 - Phosphated flour.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Phosphated flour. 137.175 Section 137.175 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Related Products § 137.175 Phosphated flour. Phosphated flour, phosphated white flour, and phosphated...

Design of Sustainable Blended Products using an Integrated Methodology

DEFF Research Database (Denmark)

Yunus, Nor Alafiza Binti; Gernaey, Krist; Woodley, John

2013-01-01

This paper presents a systematic methodology for designing blended products consisting of three stages; product design, process identification and experimental verification. The product design stage is considered in this paper. The objective of this stage is to screen and select suitable chemicals...... to be used as building blocks in the mixture design, and then to propose the blend formulations that fulfill the desired product attributes. The result is a set of blends that match the constraints, the compositions, values of the target properties and information about their miscibility. The methodology has...... been applied to design several blended products. A case study on design of blended lubricants is highlighted. The objective is to identify blended products that satisfy the product attributes with at least similar or better performance compared to conventional products....

Thermal and mechanical properties of aluminized fabrics for use in ferrous metal handling operations.

Science.gov (United States)

Wren, J E; Scott, W D; Bates, C E

1977-11-01

Protective garments are normally worn in molten handling operations to provide some protection against molten metal splashes. These garments are also intended to provide protection against radiant heat, and they should be as heat resistant and comfortable as possible. Asbestos-based fabrics have been employed for many years, but recently some concern has been expressed over possible asbestos exposure. This program was undertaken to explore the ability of several types of fabrics to resist heat transfer during molten metal impact. A molten metal splash test, along with standard methods for determining tensile strength, flame resistance, and abrasion-flexing resistance were used to evaluate several classes of protective fabrics. The results indicate that there are materials available that offer equal or better mechanical properties and thermal protection compared to aluminized asbestos.

Dual Energy Computed Tomography to Evaluate Hepatocellular Carcinoma Treated with Transcatheter Arterial Chemo-Embolization: Comparison between the Linear Blending and Nonlinear Moidal Blending Methods

International Nuclear Information System (INIS)

Shin, Sang Soo; Kim, Hyeong Wook; Lee, Daun; Kang, Heoung Keun; Kim, Jin Woong; Heo, Suk Hee; Jeong, Yong Yeon; Seon, Hyun Ju

2012-01-01

To compare the linear blending image with the nonlinear moidal blending image using dual energy CT for the evaluation of the viable portion of hepatocellular carcinoma (HCC) after transcatheter arterial chemoembolization (TACE). One-hundred and twenty three HCC patients incompletely treated after TACE were enrolled in this study. The dual energy mode (80 kVp and Sn140 kVp) was only applied in the late arterial phase scanning. A paired t-test was used to compare the lesion-to-liver contrast-to-noise ratio (CNR) and the image noise between the two blending images. Lesion conspicuity, image sharpness, image noise and the overall image quality between the two blending images were compared using the Wilcoxon matched-pair signed-ranks test. The lesion-to-liver CNR was significantly higher on the moidal blending image (5.6 ± 3.2) than on the linear blending image (2.7 ± 1.6) (p < 0.001). The image noise was significantly lower on the moidal blending image (10.9 ± 3.5) than on the linear blending image (17.5 ± 5.5) (p < 0.001). The lesion conspicuity and overall image quality were significantly better on the moidal blending image for both reviewers (p < 0.001). However, with respect to image sharpness, the linear blending image was significantly better for both reviewers (p < 0.01). The nonlinear moidal blending image of dual energy CT showed an increased lesion-to-liver CNR, decreased noise and improved overall image quality for the evaluation of the viable portion of HCC after TACE.

Preparation of LDPE/LNR Blend Via Emulsion Dispersion

International Nuclear Information System (INIS)

Rusli Daik; Yee Lee Ching

2007-01-01

Low density polyethylene (LDPE)/ liquid natural rubber (LNR) blends with the composition of 100LDPE/ 0LNR, 70LDPE/ 30LNR, 60LDPE/ 40LNR and 40LDPE/ 60LNR were prepared via dispersion of LDPE and LNR emulsion. LNR was obtained via photochemical sensitization of natural rubber (NR). Emulsion of LNR was prepared by using sodium dodecyl sulfate (SDS) and 1-hexanol as the emulsifier and co- emulsifier respectively. Emulsion of LDPE was prepared in the same way by using LDPE solution in carbon tetrachloride, SDS and 1-hexanol. LDPE/ LNR blends were prepared via mixing of LNR and LDPE emulsions. Mechanical properties of the blends were analyzed by tensile, hardness and impact test. Optimum mechanical properties were observed for composite with composition of 60LDPE/ 40LNR that showed the maximum value of stress and strain. The glass transition temperature, T g , of the blends as obtained from differential scanning calorimetric (DSC) showed that the blends were homogeneous. Morphology study by using scanning electron microscopy (SEM) also indicates the homogeneity of LDPE/ LNR blends produced. (author)

Preparation and Characterization of Keratin/Alginate Blend Microparticles

Directory of Open Access Journals (Sweden)

Yaowalak Srisuwan

2018-01-01

Full Text Available The water-in-oil (W/O emulsification-diffusion method was used for construction of keratin (Ker, alginate (Alg, and Ker/Alg blend microparticles. The Ker, Alg, and Ker/Alg blend solutions were used as the water phase, while ethyl acetate was used as the oil phase. Firstly, different concentrations of Ker solution was used to find suitable content. 1.6% w/v Ker solution was blended with the same concentration of the Alg solution for further microparticle construction. Results from scanning electron microscope analysis show that the microparticles have different shapes: spherical, bowl-like, porous, and hollow, with several sizes depending on the blend ratio. FTIR and TG analyses indicated that the secondary structure and thermal stability of the microparticles were influenced by the Ker/Alg blend ratio. The interaction between functional groups of keratin and alginate was the main factor for both β-sheet structure and Td,max values of the microparticles. The results suggested that Ker/Alg blend microparticles might be applied in many fields by varying the Ker/Alg ratio.

Blended Learning Opportunities in Ukrainian IT Public Education

Science.gov (United States)

Szimkovics, Tamás

2017-01-01

Based on previous surveys the usage of ICT and blended learning is at a low level in Ukraine. To catch up with the European average, it is important to familiarize the students and teachers with blended learning in the secondary school. The information technology classes provide the best opportunity to introduce the blended learning, because they…

Multiscattering illumination in blended acquisition design

NARCIS (Netherlands)

Berkhout, A.J.; Blacquière, G.; Verschuur, D.J.

2010-01-01

In traditional seismic surveys the firing time between shots is such that the records do not interfere in time. However, in the concept of blending the records do overlap, allowing much denser and wider geometries in an economic way. The blending parameters are the locations of the involved sources

Blended Learning in Vocational Education: Teachers' Conceptions of Blended Learning and Their Approaches to Teaching and Design

Science.gov (United States)

Bliuc, Ana-Maria; Casey, Grant; Bachfischer, Agnieszka; Goodyear, Peter; Ellis, Robert A.

2012-01-01

This paper presents research exploring teachers' experiences of using blended learning in vocational education. Teachers involved in designing and teaching using blended learning from a major Australian vocational education provider participated in the study. They received open-ended questionnaires asking to describe their conceptions of blended…

Blended Learning in Action: A Practical Guide toward Sustainable Change

Science.gov (United States)

Tucker, Catlin R.; Wycoff, Tiffany; Green, Jason T.

2017-01-01

Blended learning has the power to reinvent education, but transitioning to a blended model is challenging. Blended learning requires a fundamentally new approach to learning as well as a new skillset for both teachers and school leaders. Loaded with research, examples, and resources, "Blended Learning in Action" demonstrates the…

A drop penetration method to measure powder blend wettability.

Science.gov (United States)

Wang, Yifan; Liu, Zhanjie; Muzzio, Fernando; Drazer, German; Callegari, Gerardo

2018-03-01

Water wettability of pharmaceutical blends affects important quality attributes of final products. We investigate the wetting properties of a pharmaceutical blend lubricated with Magnesium Stearate (MgSt) as a function of the mechanical shear strain applied to the blend. We measure the penetration dynamics of sessile drops deposited on slightly compressed powder beds. We consider a blend composed of 9% Acetaminophen 90% Lactose and 1% MgSt by weight. Comparing the penetration time of water and a reference liquid Polydimethylsiloxane (silicon oil) we obtain an effective cosine of the contact angle with water, based on a recently developed drop penetration method. We repeat the experiments for blends exposed to increasing levels of shear strain and demonstrate a significant decrease in water wettability (decrease in the cosine of the contact angle). The results are consistent with the development of a hydrophobic film coating the powder particles as a result of the increased shear strain. Finally, we show that, as expected dissolution times increase with the level of shear strain. Therefore, the proposed drop penetration method could be used to directly assess the state of lubrication of a pharmaceutical blend and act as a quality control on powder blend attributes before the blend is tableted. Copyright © 2017 Elsevier B.V. All rights reserved.

Non-isothermal crystallization of PET/PLA blends

International Nuclear Information System (INIS)

Chen, Huipeng; Pyda, Marek; Cebe, Peggy

2009-01-01

Binary blends of poly(ethylene terephthalate) with poly(lactic acid), PET/PLA, were studied by differential scanning calorimetry and X-ray scattering. The PET/PLA blends, prepared by solution casting, were found to be miscible in the melt over the entire composition range. Both quenched amorphous and semicrystalline blends exhibit a single, composition dependent glass transition temperature. We report the non-isothermal crystallization of (a) PET, with and without the presence of PLA crystals and (b) PLA, with and without the presence of PET crystals. PET can crystallize in all blends, regardless of whether PLA is amorphous or crystalline, and degree of crystallinity of PET decreases as PLA content increases. In contrast, PLA crystallization is strongly affected by the mobility of the PET fraction. When PET is wholly amorphous, PLA can crystallize even in 70/30 blends, albeit weakly. But when PET is crystalline, PLA cannot crystallize when its own content drops below 0.90. These different behaviors may possibly be related to the tendency of each polymer to form constrained chains, i.e., to form the rigid amorphous fraction, or RAF. PET is capable of forming a large amount of RAF, whereas relatively smaller amount of RAF forms in PLA. Like the crystals, the rigid amorphous fraction of one polymer component may inhibit the growth of crystals of the other blend partner.

Chitosan-Based Polymer Blends: Current Status and applications

International Nuclear Information System (INIS)

Hefian, E.A.E.; Nasef, M.M.

2014-01-01

This paper reviews the latest developments in chitosan-based blends and their potential applications in various fields. Various blends together with other derivatives, such as composites and graft copolymers, have been developed to overcome chitosans disadvantages, including poor mechanical properties and to improve its functionality towards specific applications. The progress made in blending chitosan with synthetic and natural polymers is presented. The versatility and unique characteristics, such as hydrophilicity, film-forming ability, biodegradability, biocompatibility, antibacterial activity and non-toxicity of chitosan has contributed to the successful development of various blends for medical, pharmaceutical, agricultural and environmental applications. (author)

TANK 21 AND TANK 24 BLEND AND FEED STUDY: BLENDING TIMES, SETTLING TIMES, AND TRANSFERS

Energy Technology Data Exchange (ETDEWEB)

Lee, S.; Leishear, R.; Poirier, M.

2012-05-31

The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks were evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 {micro}m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion (<1200 mg/l). (4) Experimental tests with sludge batch 6 simulant and field turbidity data from a recent Tank 21 mixing evolution suggest the solid

Shape memory behaviour of radiation-crosslinked PCL/PMVS blends

International Nuclear Information System (INIS)

Zhu Guangming; Xu Shuogui; Wang Jinhua; Zhang Longbin

2006-01-01

The performance and radiation crosslinking of polycaprolactone (PCL) and polymethylvinylsiloxane (PMVS) blends has been investigated. Radiation crosslinking of PCL/PMVS blends followed the Charlesby-Pinner equation, and PMVS promoted the radiation crosslinking of the blends. As the concentration of PMVS increased, the gelation dose and the ratio of degradation to crosslinking (p 0 /q 0 ) decreased and the efficiency of radiation crosslinking increased. The elastic modulus below the melting point of PCL of radiation-crosslinked PCL/PMVS blends decreased with the increase of PMVS, and increased above the melting point. The crosslinked PCL/PMVS blends exhibited excellent shape memory effects, and the ratios of deformation to recovery were more than 95%

Method to blend separator powders

Science.gov (United States)

Guidotti, Ronald A.; Andazola, Arthur H.; Reinhardt, Frederick W.

2007-12-04

A method for making a blended powder mixture, whereby two or more powders are mixed in a container with a liquid selected from nitrogen or short-chain alcohols, where at least one of the powders has an angle of repose greater than approximately 50 degrees. The method is useful in preparing blended powders of Li halides and MgO for use in the preparation of thermal battery separators.

Structural simulation of superlattices in lithium aluminates; Simulacion estructural de superredes en aluminatos de litio

Energy Technology Data Exchange (ETDEWEB)

Carrera G, L.M.; Basurto S, R. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1997-07-01

Among the materials to be used on the tritium generator cover of the future fusion reactors the lithium aluminate ({gamma} - LiAlO{sub 2}) is one of the more studied. In this work it is presented the superlattice structural simulation that presents to {gamma} - LiAlO{sub 2} as main phase and to {alpha} - LiAlO{sub 2} as the secondary phase. The simulation is developed considering that as the two phases present different symmetry ({gamma} - LiAlO{sub 2} is tetrahedral and {alpha} - LiAlO{sub 2} is hexahedral) it is had a superlattice LUCS type (Layered Ultrathin Coherent Structure) that is it presents an structure in coherent ultrathin layers since it is what implicates a lesser energy of formation. (Author)

Study of PP/Polybutene Blends Modified by Gamma Irradiation and HMS-PP/Polybutene Blends

International Nuclear Information System (INIS)

Lugao, A. B.

2006-01-01

The polypropylene (PP) has been applied to a wide range of production due to its various excellent properties such as cheapness, high stiffness, chemical resistance, no environmental pollution when incinerated, low specific density and good mechanical properties. However, PP is a linear polymer which exhibits low melt strength. One of the effective approaches to achieve high melt strength (HMS) is to add chain branches onto backbone polymers. High melt strength polypropylene (HMS-PP) has been recently developed and introduced in the market by the major international polypropylene producers. As a consequence different methods have been applied to modify polypropylenes by chain branches. The technology obtained by IPEN together with EMBRARAD and BRASKEM comprises chain branches added onto backbone species using gamma radiation, which is generated from a Co 6 0 source. Such radiation is very convenient in order to improve polymer materials by grafting, crosslinking and degradation. Another important approach to the development of polymer materials is based on the combination of different polymers into a new product having some of the desired properties of each component. In this work, gamma irradiation technique was used to induce chemical changes in commercial polypropylene (HMS-PP) that was after blended with polybutene and in polypropylene/polybutene blends. The samples were irradiated with a 60 C o source at doses of 12,5 and 20kGy in the presence of acetylene. It was investigated how the two different routes of blends processing can modify their properties. Indeed the results from melt flow, gel fraction and rheology reveal the influence of the process route in the blends properties. Effects on the elongation at break and break strength were observed by the results of mechanical tests. The results from rheology demonstrated an increase in melt strength and drawability of the blends

Blended learning in health education: three case studies.

Science.gov (United States)

de Jong, Nynke; Savin-Baden, Maggi; Cunningham, Anne Marie; Verstegen, Daniëlle M L

2014-09-01

Blended learning in which online education is combined with face-to-face education is especially useful for (future) health care professionals who need to keep up-to-date. Blended learning can make learning more efficient, for instance by removing barriers of time and distance. In the past distance-based learning activities have often been associated with traditional delivery-based methods, individual learning and limited contact. The central question in this paper is: can blended learning be active and collaborative? Three cases of blended, active and collaborative learning are presented. In case 1 a virtual classroom is used to realize online problem-based learning (PBL). In case 2 PBL cases are presented in Second Life, a 3D immersive virtual world. In case 3 discussion forums, blogs and wikis were used. In all cases face-to-face meetings were also organized. Evaluation results of the three cases clearly show that active, collaborative learning at a distance is possible. Blended learning enables the use of novel instructional methods and student-centred education. The three cases employ different educational methods, thus illustrating diverse possibilities and a variety of learning activities in blended learning. Interaction and communication rules, the role of the teacher, careful selection of collaboration tools and technical preparation should be considered when designing and implementing blended learning.

Quantification of rice bran oil in oil blends

Energy Technology Data Exchange (ETDEWEB)

Mishra, R.; Sharma, H. K.; Sengar, G.

2012-11-01

Blends consisting of physically refined rice bran oil (PRBO): sunflower oil (SnF) and PRBO: safflower oil (SAF) in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil. (Author) 23 refs.

Structuring of Interface-Modified Polymer Blends

DEFF Research Database (Denmark)

Lyngaae-Jørgensen, Jørgen

1999-01-01

The paper treats the case where blends of polystyrene (PS), poly (dimethylsiloxane) (PDMS) and a diblock copolymer of PS and PDMS are used as model materials. This modelsystem is predicted to be "stable" in discrete blends in simple shear flow. Stable in the sence that the block copolymer can not...

Estimated inventory of chemicals added to underground waste tanks, 1944--1975

International Nuclear Information System (INIS)

Allen, G.K.

1976-03-01

The five major chemical processes, the Bismuth Phosphate process, the Uranium Recovery process, the Redox process, the Purex process, and the Waste Fractionization process have each contributed to give the total Hanford waste chemicals. Each of these processes is studied to determine the total estimated chemicals stored in underground waste tanks. The chemical contents are derived mainly from flowsheet compositions and recorded waste volumes sent to underground storage. The major components and amounts of Hanford waste are sodium hydroxide, 230 million gram-moles (20 million pounds), sodium nitrate, 1400 million gram-moles (270 million pounds), sodium nitrite, 220 million gram-moles (34 million pounds), sodium aluminate, 400 million gram-moles (72 million pounds), and sodium phosphate, 87 million gram-moles (31 million pounds). Chemical analyses of the sludge and salt cake samples are tabulated to determine the chemical characteristics of the solids. A relative chemical toxicity of the Hanford underground waste tank chemicals is developed from maximum permissible chemical concentrations in air and water. The most toxic chemicals are assumed to be sodium phosphate--35%, sodium aluminate--28%, and chromium hydroxide--19%. If air standards set toxicity limits, the most toxic chemicals are bismuth--41%, chromium hydroxide--23%, and fluoride--10%

Modification of polymer blends by irradiation

International Nuclear Information System (INIS)

Zuchowska, D.; Zagorski, Z.P.

1999-01-01

Modification of polymers, especially of polyolefin-elastomer blends (e. g. ethylene/propylene/diene terpolymer, ethylene propylene copolymer, ethylene/vinyl acetate copolymer etc.), by irradiation with a beam of fast electrons is discussed. Irradiation of polymer blends usually results in enhanced interactions between the constituents, caused among other things, by grafting induced at the polymer interphase. As a result, mechanical properties are affected to an extent depending on the proportion and type of constituent polymers, stabilizer content and radiation dose. Breaking strength (σ) relative elongation at break (ε) and melt flow rate (MFR), were examined for a triblock styrene/butadiene/styrene (SBS) copolymer, polypropylene (PP), and a PP-SBS blend (50:50 by wt.). In PP, the content of the crystal phase was determined. Irradiation was found to make SBS crosslink, as a result, σ rose by 25% and ε remained unaffected. PP was found to become degraded upon irradiation (MFR rose as much as 16 times), thereby σ and ε decreased considerably. In pure PP, the content of the crystal phase was found to increase. The variations of σ and ε in the irradiated PP-SBS blend follow a tendency similar to that in the SBS copolymer examined. This fact suggests the SBS copolymer to have a decisive effect on the macroscopic properties of the PP-SBS blend. (author)

Reducing DRIFT backgrounds with a submicron aluminized-mylar cathode

Science.gov (United States)

Battat, J. B. R.; Daw, E.; Dorofeev, A.; Ezeribe, A. C.; Fox, J. R.; Gauvreau, J.-L.; Gold, M.; Harmon, L.; Harton, J.; Lafler, R.; Landers, J.; Lauer, R. J.; Lee, E. R.; Loomba, D.; Lumnah, A.; Matthews, J.; Miller, E. H.; Mouton, F.; Murphy, A. St. J.; Paling, S. M.; Phan, N.; Sadler, S. W.; Scarff, A.; Schuckman, F. G.; Snowden-Ifft, D.; Spooner, N. J. C.; Walker, D.

2015-09-01

Background events in the DRIFT-IId dark matter detector, mimicking potential WIMP signals, are predominantly caused by alpha decays on the central cathode in which the alpha particle is completely or partially absorbed by the cathode material. We installed a 0.9 μm thick aluminized-mylar cathode as a way to reduce the probability of producing these backgrounds. We study three generations of cathode (wire, thin-film, and radiologically clean thin-film) with a focus on the ratio of background events to alpha decays. Two independent methods of measuring the absolute alpha decay rate are used to ensure an accurate result, and agree to within 10%. Using alpha range spectroscopy, we measure the radiologically cleanest cathode version to have a contamination of 3.3±0.1 ppt 234U and 73±2 ppb 238U. This cathode reduces the probability of producing an RPR from an alpha decay by a factor of 70±20 compared to the original stainless steel wire cathode. First results are presented from a texturized version of the cathode, intended to be even more transparent to alpha particles. These efforts, along with other background reduction measures, have resulted in a drop in the observed background rate from 500/day to 1/day. With the recent implementation of full-volume fiducialization, these remaining background events are identified, allowing for background-free operation.

A blending rule for octane numbers of PRFs and TPRFs with ethanol

KAUST Repository

AlRamadan, Abdullah S.; Sarathy, Mani; Khurshid, Muneeb; Badra, Jihad

2016-01-01

-gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates blends may enable a better understanding of ethanol blending with complex multi-component gasoline fuels. This study presents a blending rule

Teaching Parametric Urban Design in a Blended Learning Format

DEFF Research Database (Denmark)

Steinø, Nicolai

2015-01-01

On the basis of a theoretical discussion of the concept of blended learning, this paper presents the pre- paration, execution and evaluation of a 5 ECTS blended learning course on parametric urban design for a group of some 50 BSc students of architecture and design at Aalborg university...... and curriculum develop- ment, and di culties to nd time for research. Despite the general consensus that developing online/blended learning courses requires both technical support, complex software installations, and substantial preparation time, it is shown that free web ser- vices and low-tech adaptations...... of traditional teaching assets are su cient to get started with blended learning with only little extra e ort. While the pilot blended learning course which provided the insights for this paper has room for impro- vement, it represents a decent rst shot at developing blended learning courses for higher education...

Optimization of the octane response of gasoline/ethanol blends

KAUST Repository

Badra, Jihad; AlRamadan, Abdullah S.; Sarathy, Mani

2017-01-01

The octane responses of gasoline/ethanol mixtures are not well understood because of the unidentified intermolecular interactions in such blends. In general, when ethanol is blended with gasoline, the Research Octane Number (RON) and the Motor Octane Number (MON) non-linearly increase or decrease, and the non-linearity is determined by the composition of the base gasoline and the amount of added ethanol. The complexity of commercial gasolines, comprising of hundreds of different components, makes it challenging to understand ethanol-gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates is critical to acquire knowledge about ethanol blending with complex multi-component gasoline fuels. In this study, the octane numbers (ON) of ethanol blends with five relevant gasoline surrogate molecules were measured. The molecules investigated in this study include: n-pentane, iso-pentane, 1,2,4-trimethylbenzene, cyclopentane and 1-hexene. These new measurements along with the available data of n-heptane, iso-octane, toluene, various primary reference fuels (PRF) and toluene primary reference fuels (TPRF) with ethanol are used to develop a blending rule for the octane response (RON and MON) of multi-component blends with ethanol. In addition, new ON data are collected for six Fuels for Advanced Combustion Engine (FACE) with ethanol. The relatively simple volume based model successfully predicts the octane numbers (ON) of the various ethanol/PRF and ethanol/TPRF blends with the majority of predictions being within the ASTM D2699 (RON) and D2700 (MON) reproducibility limits. The model is also successfully validated against the ON of the FACE gasolines blended with ethanol with the majority of predictions being within the reproducibility limits. Finally, insights into the possible causes of the synergistic and antagonistic effects of different molecules with ethanol are provided.

Optimization of the octane response of gasoline/ethanol blends

KAUST Repository

Badra, Jihad

2017-07-04

The octane responses of gasoline/ethanol mixtures are not well understood because of the unidentified intermolecular interactions in such blends. In general, when ethanol is blended with gasoline, the Research Octane Number (RON) and the Motor Octane Number (MON) non-linearly increase or decrease, and the non-linearity is determined by the composition of the base gasoline and the amount of added ethanol. The complexity of commercial gasolines, comprising of hundreds of different components, makes it challenging to understand ethanol-gasoline synergistic/antagonistic blending effects. Understanding ethanol blending effects with simpler gasoline surrogates is critical to acquire knowledge about ethanol blending with complex multi-component gasoline fuels. In this study, the octane numbers (ON) of ethanol blends with five relevant gasoline surrogate molecules were measured. The molecules investigated in this study include: n-pentane, iso-pentane, 1,2,4-trimethylbenzene, cyclopentane and 1-hexene. These new measurements along with the available data of n-heptane, iso-octane, toluene, various primary reference fuels (PRF) and toluene primary reference fuels (TPRF) with ethanol are used to develop a blending rule for the octane response (RON and MON) of multi-component blends with ethanol. In addition, new ON data are collected for six Fuels for Advanced Combustion Engine (FACE) with ethanol. The relatively simple volume based model successfully predicts the octane numbers (ON) of the various ethanol/PRF and ethanol/TPRF blends with the majority of predictions being within the ASTM D2699 (RON) and D2700 (MON) reproducibility limits. The model is also successfully validated against the ON of the FACE gasolines blended with ethanol with the majority of predictions being within the reproducibility limits. Finally, insights into the possible causes of the synergistic and antagonistic effects of different molecules with ethanol are provided.

A blend of Sodium Humate/SLES/Herbal Oils

Directory of Open Access Journals (Sweden)

Yeliz Akyiğit

2013-08-01

Full Text Available A blend of sodium humate (SH with anionic surfactants such as sodium lauryl ether sulfate (SLES was prepared by solution mixing at medium of herbal oils at 25, 50 and 75°C. Its miscibility studies were carried out by using physical techniques over an extended range of concentration and composition in buffer solution. In addition, to ascertain the state of miscibility of the blends, they were investigated by using UV-visible spectrophotometer and Fourier transform infrared (FTIR. These values revealed that the blend is miscible when the sodium humate content is more than %60 in the blend at all temperatures. There were no important differences in the characteristics of the blends at different temperatures.It was thought that the mechanism ofthe complex formation is realized by making strong intermolecular interaction like hydrogen bonds between the carbonyl groups in humic acid and hydroxyl groups in fatty acids.

Photonic polymer-blend structures and method for making

Science.gov (United States)

Barnes, Michael D.

2004-06-29

The present invention comprises the formation of photonic polymer-blend structures having tunable optical and mechanical properties. The photonic polymer-blend structures comprise monomer units of spherical microparticles of a polymer-blend material wherein the spherical microparticles have surfaces partially merged with one another in a robust inter-particle bond having a tunable inter-particle separation or bond length sequentially attached in a desired and programmable architecture. The photonic polymer-blend structures of the present invention can be linked by several hundred individual particles sequentially linked to form complex three-dimensional structures or highly ordered two-dimensional arrays of 3D columns with 2D spacing.

Blending Study For SRR Salt Disposition Integration: Tank 50H Scale-Modeling And Computer-Modeling For Blending Pump Design, Phase 2

International Nuclear Information System (INIS)

Leishear, R.; Poirier, M.; Fowley, M.

2011-01-01

The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where 300,000-800,000 gallons of salt solution will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. Blending requires the miscible salt solutions from potentially multiple source tanks per batch to be well mixed without disturbing settled sludge solids that may be present in a Blend Tank. Disturbing solids may be problematic both from a feed quality perspective as well as from a process safety perspective where hydrogen release from the sludge is a potential flammability concern. To develop the necessary technical basis for the design and operation of blending equipment, Savannah River National Laboratory (SRNL) completed scaled blending and transfer pump tests and computational fluid dynamics (CFD) modeling. A 94 inch diameter pilot-scale blending tank, including tank internals such as the blending pump, transfer pump, removable cooling coils, and center column, were used in this research. The test tank represents a 1/10.85 scaled version of an 85 foot diameter, Type IIIA, nuclear waste tank that may be typical of Blend Tanks used in SDI. Specifically, Tank 50 was selected as the tank to be modeled per the SRR, Project Engineering Manager. SRNL blending tests investigated various fixed position, non-rotating, dual nozzle pump designs, including a blending pump model provided by the blend pump vendor, Curtiss Wright (CW). Primary research goals were to assess blending times and to evaluate incipient sludge disturbance for waste tanks. Incipient sludge disturbance was defined by SRR and SRNL as minor blending of settled sludge from the tank bottom into suspension due to blending pump operation, where

BLENDING STUDY FOR SRR SALT DISPOSITION INTEGRATION: TANK 50H SCALE-MODELING AND COMPUTER-MODELING FOR BLENDING PUMP DESIGN, PHASE 2

Energy Technology Data Exchange (ETDEWEB)

Leishear, R.; Poirier, M.; Fowley, M.

2011-05-26

The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where 300,000-800,000 gallons of salt solution will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. Blending requires the miscible salt solutions from potentially multiple source tanks per batch to be well mixed without disturbing settled sludge solids that may be present in a Blend Tank. Disturbing solids may be problematic both from a feed quality perspective as well as from a process safety perspective where hydrogen release from the sludge is a potential flammability concern. To develop the necessary technical basis for the design and operation of blending equipment, Savannah River National Laboratory (SRNL) completed scaled blending and transfer pump tests and computational fluid dynamics (CFD) modeling. A 94 inch diameter pilot-scale blending tank, including tank internals such as the blending pump, transfer pump, removable cooling coils, and center column, were used in this research. The test tank represents a 1/10.85 scaled version of an 85 foot diameter, Type IIIA, nuclear waste tank that may be typical of Blend Tanks used in SDI. Specifically, Tank 50 was selected as the tank to be modeled per the SRR, Project Engineering Manager. SRNL blending tests investigated various fixed position, non-rotating, dual nozzle pump designs, including a blending pump model provided by the blend pump vendor, Curtiss Wright (CW). Primary research goals were to assess blending times and to evaluate incipient sludge disturbance for waste tanks. Incipient sludge disturbance was defined by SRR and SRNL as minor blending of settled sludge from the tank bottom into suspension due to blending pump operation, where

Improving Curriculum through Blended Learning Pedagogy

Science.gov (United States)

Darojat, Ojat

2016-01-01

This paper is a study of blended learning pedagogy in open and distance learning (ODL), involving two universities in Southeast Asia, STOU Thailand and UT Indonesia. The purpose of this study is to understand the issues related to the implementation of blended-learning pedagogy. Qualitative case study was employed to optimize my understanding of…

CURING AND MECHANICAL PROPERTIES OF CHLOROSULPHONATED POLYETHYLENE RUBBER BLEND

Directory of Open Access Journals (Sweden)

Jaroslava Budinski-Simendić

2011-09-01

Full Text Available In this paper, the curing and mechanical properties of two series of prepared blends, i.e., chlorosulphonated polyethylene (CSM/isobutylene-co-isoprene (IIR rubber blends and chlorosulphonated polyethylene (CSM/chlorinated isobutylene-co-isoprene (CIIR rubber blends were carried out. Blends were prepared using a two-roll mill at a temperature of 40-50 °C. The curing was assessed using a Monsanto oscillating disc rheometer R-100. The process of vulcanization accelerated sulfur of pure rubbers and their blends was carried out in an electrically heated laboratory hydraulic press under a pressure of about 4 MPa and 160 °C. The stress-strain experiments were performed using a tensile tester machine (Zwick 1425. Results indicate that the scorch time, ts2, and optimum cure time, tc90, increase with increasing CSM content in both blends. The value of modulus at 100 and 300% elongation and tensile strength increases with increasing CSM content, whereas elongation at break shows a decreasing trend. The enhancement in mechanical properties was supported by data of crosslink density in these samples obtained from swelling measurement and scanning electron microscopy studies of the rubber blends fractured surfaces

Evaluation of Anti-Knock Quality of Dicyclopentadiene-Gasoline Blends

KAUST Repository

Al-Khodaier, Mohannad

2017-03-28

Increasing the anti-knock quality of gasoline fuels can enable higher efficiency in spark ignition engines. In this study, the blending anti-knock quality of dicyclopentadiene (DCPD), a by-product of ethylene production from naphtha cracking, with various gasoline fuels is explored. The blends were tested in an ignition quality tester (IQT) and a modified cooperative fuel research (CFR) engine operating under homogenous charge compression ignition (HCCI) and knock limited spark advance (KLSA) conditions. Due to current fuel regulations, ethanol is widely used as a gasoline blending component in many markets. In addition, ethanol is widely used as a fuel and literature verifying its performance. Moreover, because ethanol exhibits synergistic effects, the test results of DCPD-gasoline blends were compared to those of ethanol-gasoline blends. The experiments conducted in this work enabled the screening of DCPD auto-ignition characteristics across a range of combustion modes. The synergistic blending nature of DCPD was apparent and appeared to be greater than that of ethanol. The data presented suggests that DCPD has the potential to be a high octane blending component in gasoline; one which can substitute alkylates, isomerates, reformates, and oxygenates.

Evaluation of Anti-Knock Quality of Dicyclopentadiene-Gasoline Blends

KAUST Repository

Al-Khodaier, Mohannad; Bhavani Shankar, Vijai Shankar; Waqas, Muhammad; Naser, Nimal; Sarathy, Mani; Johansson, Bengt

2017-01-01

Increasing the anti-knock quality of gasoline fuels can enable higher efficiency in spark ignition engines. In this study, the blending anti-knock quality of dicyclopentadiene (DCPD), a by-product of ethylene production from naphtha cracking, with various gasoline fuels is explored. The blends were tested in an ignition quality tester (IQT) and a modified cooperative fuel research (CFR) engine operating under homogenous charge compression ignition (HCCI) and knock limited spark advance (KLSA) conditions. Due to current fuel regulations, ethanol is widely used as a gasoline blending component in many markets. In addition, ethanol is widely used as a fuel and literature verifying its performance. Moreover, because ethanol exhibits synergistic effects, the test results of DCPD-gasoline blends were compared to those of ethanol-gasoline blends. The experiments conducted in this work enabled the screening of DCPD auto-ignition characteristics across a range of combustion modes. The synergistic blending nature of DCPD was apparent and appeared to be greater than that of ethanol. The data presented suggests that DCPD has the potential to be a high octane blending component in gasoline; one which can substitute alkylates, isomerates, reformates, and oxygenates.

Uranium and REE recovery from Florida phosphates – Looking back and going forward

International Nuclear Information System (INIS)

Zhang, J.; Birky, B.

2014-01-01

Uranium recovered during the production of phosphoric acid represents a significant source of nuclear fuel as the gap between uranium supply and demand is expected to grow. The phosphate industry in Florida supplied uranium to both the defense and energy sectors in the past, but market conditions ended the recovery process. Currently, the uranium is retained in the phosphoric acid and the granulated fertilizer products, diammonium and monoammonium phosphate, and dispersed on farm fields as a trace element in blended fertilizers. This represents a loss to the nuclear fuel cycle that will never be recovered. In an era of heightened awareness of sustainability and increasing pressure to reduce greenhouse gas emissions, market conditions and social factors may converge to create favorable conditions for uranium recovery to resume. However, the future may not resemble the past as uranium concentrations are lower in the newer mining areas and ion exchange challenges solvent extraction for the extraction technology of choice. New factors will also influence both the economic decision to resume recovery operations, as well as the recovery technology. Rare earth elements (REE) are also present in the processing streams at recoverable levels, and can be co-extracted with uranium using the proven solvent extraction method. REE are vital to the phosphor industry, green energy development, and technology advances in many fields. However, the world has limited REE resources, and the recovery of REE from many of these resources is both economically challenging and environmentally troublesome. Phosphate as a secondary REE resource has a great potential to fill this gap. World annual phosphate rock production has surpassed 200 million tons, representing 60,000 tons of unrecovered REE assuming an average concentration of 300 ppm. In the case of Florida, REE in the phosphate ore reports to four mining and processing streams, with approximately 10% to flotation tailings, 30-40% to

An investigation on radiation crosslinked foam of LDPE/EVA blends

International Nuclear Information System (INIS)

Siqin Dalai; Chen Wenxiu

1995-01-01

LDPE/EVA blend, irradiated by γ-ray then expansed by heat as a foam material, the EVA content in LDPE/EVA blend was benefited to form gelation. The gel fraction on irradiated LDPE/EVA blend increased with the increasing of its EVA content in a given dose. The gel fraction values of LDPE/EVA blend with 30% EVA content were higher than those of other blends in a same given dose, its gel fraction value was 1.7 times as those values of LDPE without EVA. The gel fractions on LDPE/EVA blend were increased with dose in oxygen, in air and in nitrogen, the formation of gel was limited by oxygen. The oxidation products on foam of LDPE/EVA blend were observed in nitrogen, in air and in oxygen by FTIR spectra. The LDPE/EVA blend system has no protection effect from oxidation comparison with the LDPE system without EVA which has less oxidation product than those without EVA in a same given gel fraction. The gel fraction on foam of LDPE/EVA blend around 25-35%, dose 25 ± 5kGy, irradiated by γ-ray in air or in nitrogen, with higher expansion ratio (19), smaller cell diameter (0.175mm), lower apparent density (0.042g/cm 3 ), higher tensile strength (0.40MPa) and longer elongation at break (290-360%) on foam of LDPE/EVA blend were selected. It was opitimum condition for application in this systems. The relations among gel fraction on LDPE/EVA blend, expansion ratio, apparent density, average cell diameter and mechanical properties of foamed sheet were discussed. (author)

The Effect of (Ag, Ni, Zn-Addition on the Thermoelectric Properties of Copper Aluminate

Directory of Open Access Journals (Sweden)

Jianxiao Xu

2010-01-01

Full Text Available Polycrystalline bulk copper aluminate Cu1-x-yAgxByAlO2 with B = Ni or Zn were prepared by spark plasma sintering and subsequent thermal treatment. The influence of partial substitution of Ag, Ni and Zn for Cu-sites in CuAlO2 on the high temperature thermoelectric properties has been studied. The addition of Ag and Zn was found to enhance the formation of CuAlO2 phase and to increase the electrical conductivity. The addition of Ag or Ag and Ni on the other hand decreases the electrical conductivity. The highest power factor of 1.26 × 10-4 W/mK2 was obtained for the addition of Ag and Zn at 1,060 K, indicating a significant improvement compared with the non-doped CuAlO2 sample.

A systematic methodology for design of tailor-made blended products

DEFF Research Database (Denmark)

Yunus, Nor Alafiza Binti; Gernaey, Krist; Woodley, John

2014-01-01

A systematic methodology for design of tailor-made blended products has been developed. In tailor-made blended products, one identifies the product needs and matches them by blending different chemicals. The systematic methodology has four main tasks. First, the design problem is defined: the pro......, the methodology is highlighted through two case studies involving gasoline blends and lubricant base oils....

Radioactivity of phosphate ores from Karatas-Mazidag phosphate deposit of Turkey

International Nuclear Information System (INIS)

Akyuez, T.; Varinlioglu, A.; Kose, A.; Akyuez, S.

2000-01-01

The specific activities of 238 U, 226 Ra, 232 Th and 40 K in the composite samples of phosphate ores of type I (grey-coloured ore, with high P 2 O 5 (21-35%) and low calcite content) and of type II (grey coloured calcite ore, with low P 2 O 5 content (5-17%)) of Karatas-Mazidag phosphate deposit, Turkey, have been determined by gamma spectrometry together with phosphatic animal feed ingredients. The concentrations of 238 U, 226 Ra, 232 Th and 40 K were found to be up to 557, 625, 26 and 297 Bq x kg -1 , respectively. Radium equivalent activities of samples were calculated and compared with those given in the literature. Uranium concentration of the individual phosphate samples, from which composite samples of ores of type I and II have been prepared, were found to show and increasing trend with increasing P 2 O 5 and F concentrations. (author)

Mineralogical aspects of the laterites of Maicuru

International Nuclear Information System (INIS)

Lemos, V.P.; Costa, M.C. da

1989-01-01

This paper presents the prelimary mineralogical data of the weathering materials derived from the alkaline-ultramafic-carbonatitic Maicuru complex, State of Para. These material include several minerals species: iron, titanium and aluminium oxides/hydroxides as aluminous goethite, geothite, hematite, maghemite, lepidocrocite, anatase; and gibbsite; clay minerals of the smectite, chlorite, vermiculite and kaolinite groups and interstratified chlorite-smectite, mica-vermiculite, vermiculite-chlorite and Kaolinite-smectite; and aluminous phosphates of the crandalite group, wardite, augelite, senegalite, wavelite and variscite. The principal characteristics of these minerals were obtained by X-ray diffraction, optical methods, electron probe microanalysis, energy dispersive scanning electron microscope, X-ray fluorescence, atomic absorption, inductively coupled plasma-ICP source spectrometry and colorimetric methods. (author) [pt

Phosphate application to firing range soils for Pb immobilization: The unclear role of phosphate

International Nuclear Information System (INIS)

Chrysochoou, Maria; Dermatas, Dimitris; Grubb, Dennis G.

2007-01-01

Phosphate treatment has emerged as a widely accepted approach to immobilize Pb in contaminated soils and waste media, relying on the formation of the highly insoluble mineral pyromorphite as solubility-controlling phase for Pb. As such, phosphate treatment has been proposed as a Best Management Practice (BMP) for firing ranges where Pb occurs in its metallic forms and several other phases (carbonates, oxides). While pyromorphite thermodynamically has the potential to control Pb solubility at low levels, its formation is kinetically controlled by pH, the solubility of the phosphate source, and the solubility of Pb species. Treatability studies have shown that excess quantities of soluble and acidic phosphate sources, such as phosphoric acid, are necessary for successful in situ treatment. Even under these conditions, Extended X-ray Absorption Fine Structure (EXAFS), the only reliable method to identify and quantify Pb speciation, showed that Pb conversion to pyromorphite in in situ treated soils was less than 45% after 32 months. Furthermore, the use of lime (CaO) to restore soil pH in acidified soil treatments inhibited further conversion. Additionally, phosphate treatment is known to reduce bioavailability through pyromorphite formation in the intestinal tract, and the phytoaccumulation of Pb; both desirable effects for Pb-impacted areas. Given the costs of phosphate treatment, the use of biogenic phosphate sources, such as bone meal, may be a more environmentally sustainable approach toward this end. In the many studies focusing on phosphate treatment, the attendant P leaching and eutrophication have been largely overlooked, along with other issues such as the enhanced leaching of oxyanionic contaminants, such as Se, As and W. The success and sustainability of applying phosphate as a BMP in firing range soils therefore remain questionable

Critical Success Factor for Implementing Vocational Blended Learning

Science.gov (United States)

Dewi, K. C.; Ciptayani, P. I.; Surjono, H. D.; Priyanto

2018-01-01

Blended learning provides many benefits to the flexibility of time, place and situation constraints. The research’s objectives was describing the factors that determine the successful implementation of blended learning in vocational higher education. The research used a qualitative approach, data collected through observations and interviews by questionnare based on the CSFs indicators refers to TAM and Kliger. Data analysis was inductive method. The result provided an illustration that the success of vocational blended learning implementation was largely determined by the selection of instructional models that are inline with learning achievement target. The effectiveness of blended learning required the existence of policy support, readiness of IT infrastructure. Changing lecturer’s culture by utilizing ICT can also encourage the accelerated process of successful implementation. It can concluded that determinant factor of successful implementation of blended learning in vocational education is determined by teacher’s ability in mastering the pedagogical knowledge of designing instructional models.

HEU to LEU conversion and blending facility: Oxide blending alternative to produce LEU oxide for commercial use

International Nuclear Information System (INIS)

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This document provides data to be used in the environmental impact analysis for the oxide blending HEU disposition option. This option provides for a yearly HEU throughput of 1 0 metric tons (MT) of uranium metal with an average U235 assay of 50% blended with 165 MT of natural assay triuranium octoxide (U 3 O 8 ) per year to produce 177 MT of 4% U235 assay U 3 O 8 , for LWR fuel. Since HEU exists in a variety of forms and not necessarily in the form to be blended, worst case scenarios for preprocessing prior to blending will be assumed for HEU feed streams

Performance and emission characteristics of double biodiesel blends with diesel

Directory of Open Access Journals (Sweden)

Kuthalingam Arun Balasubramanian

2013-01-01

Full Text Available Recent research on biodiesel focused on performance of single biodiesel and its blends with diesel. The present work aims to investigate the possibilities of the application of mixtures of two biodiesel and its blends with diesel as a fuel for diesel engines. The combinations of Pongamia pinnata biodiesel, Mustard oil biodiesel along with diesel (PMD and combinations of Cotton seed biodiesel, Pongamia pinnata biodiesel along with diesel (CPD are taken for the experimental analysis. Experiments are conducted using a single cylinder direct-injection diesel engine with different loads at rated 3000 rpm. The engine characteristics of the two sets of double biodiesel blends are compared. For the maximum load, the value of Specific Fuel consumption and thermal efficiency of CPD-1 blend (10:10:80 is close to the diesel values. CPD blends give better engine characteristics than PMD blends. The blends of CPD are suitable alternative fuel for diesel in stationary/agricultural diesel engines.

A robust quantitative near infrared modeling approach for blend monitoring.

Science.gov (United States)

Mohan, Shikhar; Momose, Wataru; Katz, Jeffrey M; Hossain, Md Nayeem; Velez, Natasha; Drennen, James K; Anderson, Carl A

2018-01-30

This study demonstrates a material sparing Near-Infrared modeling approach for powder blend monitoring. In this new approach, gram scale powder mixtures are subjected to compression loads to simulate the effect of scale using an Instron universal testing system. Models prepared by the new method development approach (small-scale method) and by a traditional method development (blender-scale method) were compared by simultaneously monitoring a 1kg batch size blend run. Both models demonstrated similar model performance. The small-scale method strategy significantly reduces the total resources expended to develop Near-Infrared calibration models for on-line blend monitoring. Further, this development approach does not require the actual equipment (i.e., blender) to which the method will be applied, only a similar optical interface. Thus, a robust on-line blend monitoring method can be fully developed before any large-scale blending experiment is viable, allowing the blend method to be used during scale-up and blend development trials. Copyright © 2017. Published by Elsevier B.V.

Lifecycle optimized ethanol-gasoline blends for turbocharged engines

KAUST Repository

Zhang, Bo

2016-08-16

This study presents a lifecycle (well-to-wheel) analysis to determine the CO2 emissions associated with ethanol blended gasoline in optimized turbocharged engines. This study provides a more accurate assessment on the best-achievable CO2 emission of ethanol blended gasoline mixtures in future engines. The optimal fuel blend (lowest CO2 emitting fuel) is identified. A range of gasoline fuels is studied, containing different ethanol volume percentages (E0–E40), research octane numbers (RON, 92–105), and octane sensitivities (8.5–15.5). Sugarcane-based and cellulosic ethanol-blended gasolines are shown to be effective in reducing lifecycle CO2 emission, while corn-based ethanol is not as effective. A refinery simulation of production emission was utilized, and combined with vehicle fuel consumption modeling to determine the lifecycle CO2 emissions associated with ethanol-blended gasoline in turbocharged engines. The critical parameters studied, and related to blended fuel lifecycle CO2 emissions, are ethanol content, research octane number, and octane sensitivity. The lowest-emitting blended fuel had an ethanol content of 32 vol%, RON of 105, and octane sensitivity of 15.5; resulting in a CO2 reduction of 7.1%, compared to the reference gasoline fuel and engine technology. The advantage of ethanol addition is greatest on a per unit basis at low concentrations. Finally, this study shows that engine-downsizing technology can yield an additional CO2 reduction of up to 25.5% in a two-stage downsized turbocharged engine burning the optimum sugarcane-based fuel blend. The social cost savings in the USA, from the CO2 reduction, is estimated to be as much as $187 billion/year. © 2016 Elsevier Ltd

Characterization of herbal powder blends homogeneity using near-infrared spectroscopy

Directory of Open Access Journals (Sweden)

Wenlong Li

2014-11-01

Full Text Available Homogeneity of powder blend is essential to obtain uniform contents for the tablets and capsules. Near-infrared (NIR spectroscopy with fiber-optic probe was used as an on-line technique for monitoring the homogeneity of pharmaceutical blend during the blending process instead of the traditional techniques, such as high performance liquid chromatograph (HPLC method. In this paper NIRS with a SabIR diffuse reflectance fiber-optic probe was used to monitor the blending process of coptis powder and lactose (excipient with different contents, and further qualitative methods, like similarity, moving block of standard deviation and mean square were used for calculation purposes with the collected spectra after the pretreatment of multiplicative signal correction (MSC and second derivative. Correlation spectrum was used for the wavelength selection. Four different coptis were blended with lactose separately to validate the proposed method, and the blending process of "liu wei di huang" pill was also simulated in bottles to verify this method on multiple herbal blends. The overall results suggest that NIRS is a simple, effective and noninvasive technique can be successfully applied to the determination of homogeneity in the herbal blend.

Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

International Nuclear Information System (INIS)

Ochsenfeld, W.; Schmieder, H.

1976-01-01

Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

Transitioning to Blended Learning: Understanding Student and Faculty Perceptions

Science.gov (United States)

Napier, Nannette P.; Dekhane, Sonal; Smith, Stella

2011-01-01

This paper describes the conversion of an introductory computing course to the blended learning model at a small, public liberal arts college. Blended learning significantly reduces face-to-face instruction by incorporating rich, online learning experiences. To assess the impact of blended learning on students, survey data was collected at the…

On the crystallization behavior of syndiotactic-b-atactic polystyrene stereodiblock copolymers, atactic/syndiotactic polystyrene blends, and aPS/sPS blends modified with sPS-b-aPS

Energy Technology Data Exchange (ETDEWEB)

Annunziata, Liana, E-mail: liana.annunziatta@univ-rennes1.fr [Organométalliques et Catalyse, UMR 6226 Sciences Chimiques CNRS, Université de Rennes 1, Campus de Beaulieu, F-35042 Rennes Cedex (France); Monasse, Bernard, E-mail: bernard.monasse@mines-paristech.fr [Mines-ParisTech, CEMEF, Centre de Mise en Forme des Matériaux, UMR CNRS 7635, Sophia Antipolis (France); Rizzo, Paola; Guerra, Gaetano [Dipartimento di Chimica e Biologia, Università degli studi di Salerno, Via Ponte don Melillo, I-84084 Fisciano, SA (Italy); Duc, Michel [Total Petrochemicals Research Feluy, Zone Industrielle Feluy C, B-7181 Seneffe (Belgium); Carpentier, Jean-François, E-mail: jean-francois.carpentier@univ-rennes1.fr [Organométalliques et Catalyse, UMR 6226 Sciences Chimiques CNRS, Université de Rennes 1, Campus de Beaulieu, F-35042 Rennes Cedex (France)

2013-09-16

Crystallization and morphological features of syndiotactic-b-atactic polystyrene stereodiblock copolymers (sPS-b-aPS), atactic/syndiotactic polystyrene blends (aPS/sPS), and aPS/sPS blends modified with sPS-b-aPS, with different compositions in aPS and sPS, have been investigated using differential scanning calorimetry (DSC), polarized light optical microscopy (POM) and wide angle X-ray diffraction (WAXRD) techniques. For comparative purposes, the properties of parent pristine sPS samples were also studied. WAXRD analyses revealed for all the samples, independently from their composition (aPS/sPS ratio) and structure (blends, block copolymers, blends modified with block copolymers), the same polymorphic β form of sPS. The molecular weight of aPS and sPS showed opposite effects on the crystallization of 50:50 aPS/sPS blends: the lower the molecular weight of aPS, the slower the crystallization while the lower the molecular weight of sPS, the faster the crystallization. DSC studies performed under both isothermal and non-isothermal conditions, independently confirmed by POM studies, led to a clear trend for the crystallization rate at a given sPS/aPS ratio (ca. 50:50 and 20:80): sPS homopolymers > sPS-b-aPS block copolymers ∼sPS/aPS blends modified with sPS-b-aPS copolymers > sPS/aPS blends. Interestingly, sPS-b-aPS block copolymers not only crystallized faster than blends, but also affected positively the crystallization behavior of blends. At 50:50 sPS/aPS ratio, blends (Blend-2), block copolymers (Cop-1) and blends modified with block copolymers (Blend-2-mod) crystallized via spherulitic crystalline growth controlled by an interfacial process. In all cases, an instantaneous nucleation was observed. The density of nuclei in block copolymers (160,000−190,000 nuclei mm{sup −3}) was always higher than that in blends and modified blends (30,000−60,000 nuclei mm{sup −3}), even for quite different sPS/aPS ratio. At 20:80 sPS/aPS ratio, the block copolymers

A Novel Method of Extraction of Blend Component Structure from SANS Measurements of Homopolymer Bimodal Blends.

Science.gov (United States)

Smerdova, Olga; Graham, Richard S; Gasser, Urs; Hutchings, Lian R; De Focatiis, Davide S A

2014-05-01

A new method is presented for the extraction of single-chain form factors and interchain interference functions from a range of small-angle neutron scattering (SANS) experiments on bimodal homopolymer blends. The method requires a minimum of three blends, made up of hydrogenated and deuterated components with matched degree of polymerization at two different chain lengths, but with carefully varying deuteration levels. The method is validated through an experimental study on polystyrene homopolymer bimodal blends with [Formula: see text]. By fitting Debye functions to the structure factors, it is shown that there is good agreement between the molar mass of the components obtained from SANS and from chromatography. The extraction method also enables, for the first time, interchain scattering functions to be produced for scattering between chains of different lengths. [Formula: see text].

Phosphate control in dialysis

Directory of Open Access Journals (Sweden)

Cupisti A

2013-10-01

Full Text Available Adamasco Cupisti,1 Maurizio Gallieni,2 Maria Antonietta Rizzo,2 Stefania Caria,3 Mario Meola,4 Piergiorgio Bolasco31Department of Clinical and Experimental Medicine, University of Pisa, Pisa, Italy; 2Nephrology and Dialysis Unit, San Carlo Borromeo Hospital, Milan, Italy; 3Territorial Department of Nephrology and Dialysis, ASL Cagliari, Italy; 4Sant'Anna School of Advanced Studies, University of Pisa, Pisa, ItalyAbstract: Prevention and correction of hyperphosphatemia is a major goal of chronic kidney disease–mineral and bone disorder (CKD–MBD management, achievable through avoidance of a positive phosphate balance. To this aim, optimal dialysis removal, careful use of phosphate binders, and dietary phosphate control are needed to optimize the control of phosphate balance in well-nourished patients on a standard three-times-a-week hemodialysis schedule. Using a mixed diffusive–convective hemodialysis tecniques, and increasing the number and/or the duration of dialysis tecniques are all measures able to enhance phosphorus (P mass removal through dialysis. However, dialytic removal does not equal the high P intake linked to the high dietary protein requirement of dialysis patients; hence, the use of intestinal P binders is mandatory to reduce P net intestinal absorption. Unfortunately, even a large dose of P binders is able to bind approximately 200–300 mg of P on a daily basis, so it is evident that their efficacy is limited in the case of an uncontrolled dietary P load. Hence, limitation of dietary P intake is needed to reach the goal of neutral phosphate balance in dialysis, coupled to an adequate protein intake. To this aim, patients should be informed and educated to avoid foods that are naturally rich in phosphate and also processed food with P-containing preservatives. In addition, patients should preferentially choose food with a low P-to-protein ratio. For example, patients could choose egg white or protein from a vegetable source

Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

2015-09-25

Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

Linear polarizers based on oriented polymer blends

NARCIS (Netherlands)

Jagt, H.J.B.; Dirix, Y.J.L.; Hikmet, R.A.M.; Bastiaansen, C.W.M.

1998-01-01

Linear sheet polarizers based on the anisotropic scattering of light by drawn polymer blends are introduced here. The proper selection of materials and processing conditions for the production of large-area, flexible films of phase-segregated polymer blends suitable for polarization applications are

Effect of noise in blending and deblending

NARCIS (Netherlands)

Berkhout, A.J.; Blacquière, G.

2013-01-01

If simultaneous shooting is carried out by incoherent source arrays, being the condition of blended acquisition, the deblending process generates shot records with a very low residual interference (blending noise). We found, theoretically and numerically, that deblended shot records had a better

Improvement of biodiesel methanol blends

Directory of Open Access Journals (Sweden)

Y. Datta Bharadwaz

2016-06-01

Full Text Available The main objective of this work was to improve the performance of biodiesel–methanol blends in a VCR engine by using optimized engine parameters. For optimization of the engine, operational parameters such as compression ratio, fuel blend, and load are taken as factors, whereas performance parameters such as brake thermal efficiency (Bth and brake specific fuel consumption (Bsfc and emission parameters such as carbon monoxide (CO, unburnt hydrocarbons (HC, Nitric oxides (NOx and smoke are taken as responses. Experimentation is carried out as per the design of experiments of the response surface methodology. Optimization of engine operational parameters is carried out using Derringers Desirability approach. From the results obtained it is inferred that the VCR engine has maximum performance and minimum emissions at 18 compression ratio, 5% fuel blend and at 9.03 kg of load. At this optimized operating conditions of the engine the responses such as brake thermal efficiency, brake specific fuel consumption, carbon monoxide, unburnt hydrocarbons, nitric oxide, and smoke are found to be 31.95%, 0.37 kg/kW h, 0.036%, 5 ppm, 531.23 ppm and 15.35% respectively. It is finally observed from the mathematical models and experimental data that biodiesel methanol blends have maximum efficiency and minimum emissions at optimized engine parameters.

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

OpenAIRE

Lílian Estrela Borges Baldotto; Marihus Altoé Baldotto; Fábio Lopes Olivares; Adriane Nunes de Souza

2014-01-01

Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i) to select and characterize diazotrophs abl...

effect of effect of blend ratio on blend ratio on characteristics

African Journals Online (AJOL)

User

properties, cassava-soybean composite, wheat, bread, blend ratio ... dily growing population, an in eating and ... thermodynamic variables can produce an effect on .... these conditions. ..... Ragaee, S. et al., Pasting properties of starch and.

Elastic Properties of Tricalcium Aluminate from High-Pressure Experiments and First-Principles Calculations

KAUST Repository

Moon, Juhyuk

2012-06-04

The structure and elasticity of tricalcium aluminate (C 3A) have been experimentally and theoretically studied. From high-pressure X-ray diffraction experiments, the bulk modulus of 102(6) and 110(3) GPa were obtained by fitting second- and third-order finite strain equation of state, respectively. First-principles calculations with a generalized gradient approximation gave an isotropic bulk modulus of 102.1 GPa and an isothermal bulk modulus of 106.0 GPa. The static calculations using the exchange-correlation functional show an excellent agreement with the experimental measurements. Based on the agreement, accurate elastic constants and other elastic moduli were computed. The slight difference of behavior at high pressure can be explained by the infiltration of pressure-transmitting silicone oil into structural holes in C 3A. The computed elastic and mechanical properties will be useful in understanding structural and mechanical properties of cementitious materials, particularly with the increasing interest in the advanced applications at the nanoscale. © 2012 The American Ceramic Society.

Elastic Properties of Tricalcium Aluminate from High-Pressure Experiments and First-Principles Calculations

KAUST Repository

Moon, Juhyuk; Yoon, Seyoon; Wentzcovitch, Renata M.; Clark, Simon M.; Monteiro, Paulo J.M.

2012-01-01

The structure and elasticity of tricalcium aluminate (C 3A) have been experimentally and theoretically studied. From high-pressure X-ray diffraction experiments, the bulk modulus of 102(6) and 110(3) GPa were obtained by fitting second- and third-order finite strain equation of state, respectively. First-principles calculations with a generalized gradient approximation gave an isotropic bulk modulus of 102.1 GPa and an isothermal bulk modulus of 106.0 GPa. The static calculations using the exchange-correlation functional show an excellent agreement with the experimental measurements. Based on the agreement, accurate elastic constants and other elastic moduli were computed. The slight difference of behavior at high pressure can be explained by the infiltration of pressure-transmitting silicone oil into structural holes in C 3A. The computed elastic and mechanical properties will be useful in understanding structural and mechanical properties of cementitious materials, particularly with the increasing interest in the advanced applications at the nanoscale. © 2012 The American Ceramic Society.

Improved Mechanical Properties of Compatibilized Polypropylene/Polyamide-12 Blends

Directory of Open Access Journals (Sweden)

Nora Aranburu

2015-01-01

Full Text Available Compatibilized blends of polypropylene (PP and polyamide-12 (PA12 as a second component were obtained by direct injection molding having first added 20% maleic anhydride-modified copolymer (PP-g-MA to the PP, which produced partially grafted PP (gPP. A nucleating effect of the PA12 took place on the cooling crystallization of the gPP, and a second crystallization peak of the gPP appeared in the PA12-rich blends, indicating changes in the crystalline morphology. There was a slight drop in the PA12 crystallinity of the compatible blends, whereas the crystallinity of the gPP increased significantly in the PA12-rich blends. The overall reduction in the dispersed phase particle size together with the clear increase in ductility when gPP was used instead of PP proved that compatibilization occurred. Young’s modulus of the blends showed synergistic behavior. This is proposed to be both due to a change in the crystalline morphology of the blends on the one hand and, on the other, in the PA12-rich blends, to the clear increase in the crystallinity of the gPP phase, which may, in turn, have been responsible for the increase in its continuity and its contribution to the modulus.

Uranium-phosphate relationship in phosphated chalks of the Mons and Picardie Bassins

Energy Technology Data Exchange (ETDEWEB)

Quinif, Y; Charlet, J M; Dupuis, C; Robaszynski, F [Faculte Polytechnique de Mons (Belgium)

1981-11-30

The lithological and geochemical conditions relative to the ''Senonian'' phosphatic chalks are relatively simple in the Basins of Mons (Belgium) and of Picardy (France). Their characteristics permit us to study chiefly the uranium-phosphate relation. It appears a very good linear correlation between the phosphate and the uranium. The coefficient U/P/sub 2/O/sub 5/ remains a constant from the bottom to the top of the same section, but changes in space for synchronic formations (lateral variation of geochemical facies) and in time for two separated basins.

Contribution to the study of wastes stabilization by sulfo-aluminate cement

International Nuclear Information System (INIS)

Peysson, S.

2005-02-01

Calcium sulfo-aluminate cement is mainly composed of yeelimite known to be a precursor of ettringite formation. Ettringite is able to incorporate several heavy metals by isomorphous substitutions without altering its crystalline structure. The design of a binder required for immobilizing heavy metals was undertaken. The hydration study of clinker, and cement containing 4 amounts of gypsum has been carried out by means of XRD, DTA and IR spectrometry. It was pointed out that the addition of gypsum enhances hydration. Two binders were selected: 80/20 and 70/30. The immobilisation of 7 pollutants was very successful. Nevertheless, damages appeared with the binder 70/30 containing sodium chromate and dichromate: sodium caused activation of yeelimite reactivity and important dissolution of gypsum leading to important ettringite production. With a great amount of gypsum (30 %), dissolution led to secondary ettringite formation which damaged the hardened paste. Adding polyol enhances the retention of sodium chromate. On the other hand, the immobilisation of two types of weakly radioactive wastes supplied by CEA has been made. Results obtained in terms of setting time, compressive strength and leaching were excellent. (author)

Transparent magnesium aluminate spinel: a prospective biomaterial for esthetic orthodontic brackets.

Science.gov (United States)

Krishnan, Manu; Tiwari, Brijesh; Seema, Saraswathy; Kalra, Namitha; Biswas, Papiya; Rajeswari, Kotikalapudi; Suresh, Madireddy Buchi; Johnson, Roy; Gokhale, Nitin M; Iyer, Satish R; Londhe, Sanjay; Arora, Vimal; Tripathi, Rajendra P

2014-11-01

Adult orthodontics is recently gaining popularity due to its importance in esthetics, oral and general health. However, none of the currently available alumina or zirconia based ceramic orthodontic brackets meet the esthetic demands of adult patients. Inherent hexagonal lattice structure and associated birefringence limits the visible light transmission in polycrystalline alumina and make them appear white and non transparent. Hence focus of the present study was to assess the feasibility of using magnesium aluminate (MgAl2O4) spinel; a member of the transparent ceramic family for esthetic orthodontic brackets. Transparent spinel specimens were developed from commercially available white spinel powder through colloidal shaping followed by pressureless sintering and hot isostatic pressing at optimum conditions of temperature and pressure. Samples were characterized for chemical composition, phases, density, hardness, flexural strength, fracture toughness and optical transmission. Biocompatibility was evaluated with in-vitro cell line experiments for cytotoxicity, apoptosis and genotoxicity. Results showed that transparent spinel samples had requisite physico-chemical, mechanical, optical and excellent biocompatibility for fabricating orthodontic brackets. Transparent spinel developed through this method demonstrated its possibility as a prospective biomaterial for developing esthetic orthodontic brackets.

Blended e-learning Design: Discussion of Cultural Issues

OpenAIRE

Ahmed A Al-Hunaiyyan; Salah AL-Sharhan; Nabeel Al-Huwail

2008-01-01

Blended e-learning is becoming an educational issue especially with the new development of e-learning technology and globalization. Educators as the question: can we design these systems to accommodate different cultural groups and various learning strategies. This paper addresses some design issues when selecting a blended e-learning approach; it discusses some cultural elements that affect the design of blended e-learning. The paper also explores issues related to learning design, then emph...

PAIRWISE BLENDING OF HIGH LEVEL WASTE

International Nuclear Information System (INIS)

CERTA, P.J.

2006-01-01

The primary objective of this study is to demonstrate a mission scenario that uses pairwise and incidental blending of high level waste (HLW) to reduce the total mass of HLW glass. Secondary objectives include understanding how recent refinements to the tank waste inventory and solubility assumptions affect the mass of HLW glass and how logistical constraints may affect the efficacy of HLW blending

Uranium abundance in some sudanese phosphate ores

International Nuclear Information System (INIS)

Adam, A.A.; Eltayeb, M.A.H.

2009-01-01

This work was carried out mainly to analysis of some Sudanese phosphate ores, for their uranium abundance and total phosphorus content measured as P 2 O 5 %. For this purpose, 30 samples of two types of phosphate ore from Eastern Nuba Mountains, in Sudan namely, Kurun and Uro areas were examined. In addition, the relationship between uranium and major, and trace elements were obtained, also, the natural radioactivity of the phosphate samples was measured, in order to characterize and differentiate between the two types of phosphate ores. The uranium abundance in Uro phosphate with 20.3% P 2 O 5 is five time higher than in Kurun phosphate with 26.7% P 2 O 5 . The average of uranium content was found to be 56.6 and 310 mg/kg for Kurun and Uro phosphate ore, respectively. The main elements in Kurun and Uro phosphate ore are silicon, aluminum, and phosphorus, while the most abundant trace elements in these two ores are titanium, strontium and barium. Pearson correlation coefficient revealed that uranium in Kurun phosphate shows strong positive correlation with P 2 O 5 , and its distribution is essentially controlled by the variations of P2O5 concentration, whereas uranium in Uro phosphate shows strong positive correlation with strontium, and its distribution is controlled by the variations of Sr concentration. Uranium behaves in different ways in Kurun phosphate and in Uro phosphate. Uro phosphate shows higher concentrations of all the estimated radionuclides than Kurun phosphate. According to the obtained results, it can be concluded that Uro phosphate is consider as secondary uranium source, and is more suitable for uranium recovery, because it has high uranium abundance and low P 2 O 5 %, than Kurun phosphate. (authors) [es

Contribution to the study of the sintering of finely divided alumina; Contribution a l'etude du frittage de l'alumine finement divisee

Energy Technology Data Exchange (ETDEWEB)

Vergnon, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-07-01

Two crystalline forms of alumina, delta and alpha, were used to prepare compacts. The shrinkage of these compacts was investigated at different temperatures. The samples of alumina are composed of non porous, spherical particles, of a very high purity. Their mean diameter varies between 160 and 1 200 Angstrom for the delta alumina samples and between 400 and 1 200 Angstrom for the alpha alumina samples. The shrinkage of compacts, heated at a linearly increasing temperature (300 deg. C/h, slow heating) was studied in a A.D.A.M.E.L. dilatometer, modified to be used as a retractometer. The kinetics of the isothermal shrinkage of compacts after their rapid introduction (a few seconds, flash heating) in the high temperature zone of the furnace were followed with a photographic technique. It is shown that the heating rate influences the shrinkage of the compacts when they are heated at temperatures over 1 000 deg. C. The kinetics of the isothermal shrinkage, at temperature between 1000 deg. C and 1600 deg. C were thoroughly studied. Values of the apparent activation energy for the different classes of compacts are given. An interpretation of the results is proposed. It takes into account two different but interdependent mechanisms of sintering: the disappearance of porosity as a result of vacancy diffusion and the grain growth as a result of boundary migration. (author) [French] Deux formes cristallines de l'alumine, la forme delta et la forme alpha, ont ete utilisees pour confectionner des comprimes en vue d'une etude cinetique du frittage. Ces alumines d'une tres grande purete sont constituees de particules spheriques non poreuses, sensiblement homodispersees dont le diametre moyen varie entre 160 et 1200 Angstrom pour les echantillons de l'alumine delta et entre 400 et 1200 Angstrom pour ceux de l'alumine alpha. Le retrait des comprimes chauffes a temperature linerairement croissante (300 deg. C/h: chauffage lent) a ete suivi a l'aide du dilotometre A

Synthesizing optimal waste blends

International Nuclear Information System (INIS)

Narayan, V.; Diwekar, W.M.; Hoza, M.

1996-01-01

Vitrification of tank wastes to form glass is a technique that will be used for the disposal of high-level waste at Hanford. Process and storage economics show that minimizing the total number of glass logs produced is the key to keeping cost as low as possible. The amount of glass produced can be reduced by blending of the wastes. The optimal way to combine the tanks to minimize the vole of glass can be determined from a discrete blend calculation. However, this problem results in a combinatorial explosion as the number of tanks increases. Moreover, the property constraints make this problem highly nonconvex where many algorithms get trapped in local minima. In this paper the authors examine the use of different combinatorial optimization approaches to solve this problem. A two-stage approach using a combination of simulated annealing and nonlinear programming (NLP) is developed. The results of different methods such as the heuristics approach based on human knowledge and judgment, the mixed integer nonlinear programming (MINLP) approach with GAMS, and branch and bound with lower bound derived from the structure of the given blending problem are compared with this coupled simulated annealing and NLP approach

Blended Learning or E-learning?

OpenAIRE

Tayebinik, Maryam; Puteh, Marlia

2013-01-01

ICT or Information and Communication Technology has pervaded the fields of education.In recent years the term e-learning has emerged as a result of the integration of ICT in the education fields. Following the application this technology into teaching, some pitfalls have been identified and this have led to the Blended learning phenomenon.However the preference on this new method has been debated quite extensively.The aim of this paper is to investigate the advantages of blended learning over...

Uranium from phosphate ores

International Nuclear Information System (INIS)

Hurst, F.J.

1983-01-01

The following topics are described briefly: the way phosphate fertilizers are made; how uranium is recovered in the phosphate industry; and how to detect covert uranium recovery operations in a phsophate plant

Properties, performance, and applications of biofuel blends: a review

Directory of Open Access Journals (Sweden)

Husam Al-Mashhadani

2017-08-01

Full Text Available Biofuels such as ethanol and biodiesel derived from living plants or animal matter can be used directly in their neat forms or as blends with their fossil counterparts in internal combustion engines. Although the properties and performance of neat biofuels have been extensively reported, this is not the case for many blends. The purpose of this review is to analyze different forms of biofuel blends that are under research and development comparing their utility and performance in the two primary classes of engines, i.e., spark ignition and compression ignition engines. The fuel properties, performance and emission characteristics, advantages and disadvantages of various fuel blends are compared and discussed. The analysis reveals certain blends possess better overall fuel properties and yield better overall performance than the neat or fossil forms.

The Literature Landscape of Blended Learning in Higher Education: The Need for Better Understanding of Academic Blended Practice

Science.gov (United States)

Torrisi-Steele, Geraldine; Drew, Steve

2013-01-01

If we are to realise the potential of blended learning in higher education, then further research into academic practice and relevant academic development is essential. Our review of literature on blended learning in higher education reveals an interesting scholarship landscape which, when described in detail, pointedly directs attention to the…

Phase Behavior, Thermal Stability and Rheological Properties of PPEK/PC Blends

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

Phase behavior, thermal stability and rheological properties of the blends of poly(phthalazinone ether ketone) (PPEK)with bisphenol-A polycarbonate (PC) prepared by solution coprecipitation were studied using differential scanning calorimetry (DSC), Frourier-Transform IR spectroscopy (FT-IR), thermogravimetric analysis (TGA) and capillary rheometer. The DSC results indicated that PPEK/PC blends are almost immiscible in full compositions. FT-IR investigation showed that there were no apparent specific interactions between the constituent polymers. The blends keep excellent thermal stability and the addition of PC degrades the thermal stability of blends to some degree. The thermal degradation processes of the blends are much similar to that of PC. The studies on rheological properties of blends show that blending PPEK with PC is beneficial to reducing the melt viscosity and improving the appearance of PPEK.

Hot-Dip Aluminizing on AISI F55–UNS S32760 Super Duplex Stainless Steel Properties: Effect of Thermal Treatments

Directory of Open Access Journals (Sweden)

Andrea Francesco Ciuffini

2017-11-01

Full Text Available The behavior of super duplex stainless steels AISI F55-UNS S32760 in hot-dip aluminizing process has been studied, investigating the influence of cold working and of different initial microstructures obtained through a preliminary thermal treatment. The microstructural features examined are the secondary austenite precipitation, the static recovery of ferrite and the thermal dissolution of austenite within ferritic matrix. The hot-dip aluminizing temperature has been optimized through sessile drop tests. The treatment has been performed at 1100 °C for 300 s, 900 s and 2700 s. A strong chemical interaction occurs, generating intermetallic compounds at the interface. Molten aluminum interacts exclusively with the ferritic phase due to its much higher diffusivity in this phase coupled with its marked ferrite-stabilizer behavior. Thus, the influence of cold working is not remarkable, since the strains are mainly allocated by austenitic phase. The diffusivity of aluminum increases due to lattice defects thermally generated and, mainly, to influence given by grain boundaries, multiplied by secondary austenite precipitation, which act as short-circuit diffusion paths. Ni and Cr contents in the ferritic matrix have an influence but not highly relevant. Then, the best starting condition of the super duplex stainless steel substrates, to obtain a thick interfacial layer, are the thermal annealing at 1080 °C for 360 s/mm after a solution thermal treatment at 1300 °C for 60 s/mm.

Phosphor blends for high-CRI fluorescent lamps

Science.gov (United States)

Setlur, Anant Achyut [Niskayuna, NY; Srivastava, Alok Mani [Niskayuna, NY; Comanzo, Holly Ann [Niskayuna, NY; Manivannan, Venkatesan [Clifton Park, NY; Beers, William Winder [Chesterland, OH; Toth, Katalin [Pomaz, HU; Balazs, Laszlo D [Budapest, HU

2008-06-24

A phosphor blend comprises at least two phosphors each selected from one of the groups of phosphors that absorb UV electromagnetic radiation and emit in a region of visible light. The phosphor blend can be applied to a discharge gas radiation source to produce light sources having high color rendering index. A phosphor blend is advantageously includes the phosphor (Tb,Y,LuLa,Gd).sub.x(Al,Ga).sub.yO.sub.12:Ce.sup.3+, wherein x is in the range from about 2.8 to and including 3 and y is in the range from about 4 to and including 5.

Electrochemical Reduction of Zinc Phosphate

International Nuclear Information System (INIS)

Kim, Chang Hwan; Lee, Jung Hyun; Shin, Woon Sup

2010-01-01

We demonstrated first that the electrochemical reduction of zinc phosphate in neutral phosphate buffer is possible and potentially applicable to bio-compatible rechargeable battery. The actual redox component is Zn(s)/Zn phosphate(s) and the future research about the control of crystal formation for the better cyclability is required. In lead-acid battery, the electrochemical redox reaction of Pb (s) /PbSO 4(s) is used by reducing Pb(II) and oxidizing Pb(0) in sulfate rich solution. Since both reduced form and oxidized form are insoluble, they cannot diffuse to the opposite electrodes and react. It is a very common strategy to make a stable battery electrode that a metal element is reduced and oxidized in solution containing an abundance of anion readily precipitating with the metal ion. For the application of this strategy to construction of rechargeable battery using bio-compatible electrode materials and electrolytes, the use of phosphate ion can be considered as anion readily precipitating with metal ions. If phosphate buffer with neutral pH is used as electrolyte, the better bio-compatibility will be achieved than most of rechargeable battery using strong acid, strong base or organic solvent as electrolyte solution. There are many metal ions readily precipitating with phos-phate ion, and zinc is one of them

Performance Testing of Diesel Engine using Cardanol-Kerosene oil blend

Directory of Open Access Journals (Sweden)

Ravindra

2018-01-01

Full Text Available Awareness of environmental pollution and fossil fuel depletion has necessitated the use of biofuels in engines which have a relatively cleaner emissions. Cardanol is a biofuel, abundantly available in India, which is a by-product of cashew processing industries. In this study performance of raw Cardanol blended with kerosene has been tested in diesel engine. Volumetric blend BK30 (30% kerosene and 70% Cardanol has been used for the test. The properties like flash point, viscosity and calorific value of the blend have been determined. The test was carried out in four stroke diesel engine connected with an eddy current dynamometer. Performance of the engine has been analysed by finding the brake specific fuel consumption (BSFC and brake thermal efficiency (BTE. The results showed that the brake thermal efficiency of the blend is 29.87%, with less CO and smoke emission compared to diesel. The results were also compared with the performance of Cardanol diesel blend and Cardanol camphor oil blend, which were already tested in diesel engines by other researchers. Earlier research work reveals that the blend of 30% camphor oil and 70% Cardanol performs very closer to diesel fuel with a thermal efficiency of 29.1%. Similarly, higher brake thermal efficiency was obtained for 20% Cardanol and 80% diesel blend.

Ignition characteristics of coal blends in an entrained flow furnace

Energy Technology Data Exchange (ETDEWEB)

J. Faundez; B. Arias; F. Rubiera; A. Arenillas; X. Garcia; A.L. Gordon; J.J. Pis [Universidad de Concepcion, Concepcion (Chile)

2007-09-15

Ignition tests were carried out on blends of three coals of different rank - subbituminous, high volatile and low volatile bituminous - in two entrained flow reactors. The ignition temperatures were determined from the gas evolution profiles (CO, CO{sub 2}, NO, O{sub 2}), while the mechanism of ignition was elucidated from these profiles and corroborated by high-speed video recording. Under the experimental conditions of high carbon loading, clear interactive effects were observed for all the blends. Ignition of the lower rank coals (subbituminous, high volatile bituminous) enhanced the ignition of the higher rank coal (low volatile bituminous) in the blends. The ignition temperatures of the blends of the low rank coals (subbituminous-high volatile bituminous) were additive. However, for the rest of the blends the ignition temperatures were always closer to the lower rank coal in the blend. 21 refs., 8 figs.

Physico-Chemical, Microbiological Profiles of Blends of Tea and ...

African Journals Online (AJOL)

Sample of tea obtained from Mambilla, Nigeria highland was blended with mistletoe - a known medicinal parasitic plant of cocoa. The ratios of the blends were Tea(T)/Mistletoe (M) 90:10 10:90, 75:25, 25:75, and 50:50 while ordinary tea and mistletoes served as control samples. Chemical analyses of blends were done ...

Property Analysis of Ethanol--Natural Gasoline--BOB Blends to Make Flex Fuel

Energy Technology Data Exchange (ETDEWEB)

Alleman, Teresa L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Yanowitz, Janet [Ecoengineering, Inc., Sharonville, OH (United States)

2016-11-01

Ten natural gasolines were analyzed for a wide range of properties, including Reid vapor pressure (RVP), benzene, sulfur, distillation, stability, metals, and aromatic content, to determine their quality. Benzene and sulfur content were sufficiently low in all but one of the samples that they could be blended without further upgrading. Four of these samples were selected to blend with blendstock for oxygenate blending (BOB) and ethanol to produce E51, E70, and E83 blends, targeting 7.8 and 9.0-psi finished fuels. The volume of each component in the blend was estimated using the Reddy model, with the assumption that the BOB and natural gasoline blend linearly and behave as a single component in the model calculations. Results show that the Reddy model adequately predicts the RVP of the finished blend for E51 and E70, but significantly underpredicts the RVP of E83 blends by nearly 2 psi. It is hypothesized that the underprediction is a function of the very low aromatic content of the E83 blends, even compared to the E51 and E70 blends.

Spectrographic Determination of Impurities in Ceramic Materials for Nuclear fusion Reactors. II. Analysis of Magnesium Aluminate

International Nuclear Information System (INIS)

Rucandio, M. I.; Roca, M.; Melon, A.

1990-01-01

The determination of minor and trace elements in the magnesium aluminate, considered as possible material in thermonuclear fusion reactors, has been studied. The concentration ranges are 0.1 - 0.3 % for Ca, SI and Y, and at the ppm level for Co, Cr, Fe, Hf, K, Li, Mn, Na, Ni, Se, Ta, Ti, V and Zr. Atomic emission spectroscopy with direct current are excitation and photographic detection has been employed. For Hf, Ta and Zr the use of 40% of copper fluoride as a carrier and of Nb as internal standard provide suitable sensitivities and precessions, while for the rest of elements the best results are obtained with graphite powder in different proportions and Rb or Sn as internal standard. (Author)4 refs

Spectrographic determination of impurities in ceramic materials for nuclear fusion reactors. II. Analysis of magnesium aluminate

International Nuclear Information System (INIS)

Roca, M.; Rucandio, M.I.; Melon, A.

1990-01-01

The determination of minor and trace elements in the magnesium aluminate, considered as possible mataerial in thermonuclear fusion reactors, has been studied. The concentaration ranges are 0.1-0.3 % for Ca, Si and Y, and at the ppm level for Co, Cr, Fe, Hf, K, Li, Mn, Na, Ni, Sc, Ta, Ti, V and Zr. Atomic emission spectroscopy with direct current arc excitation and photographic detection has been employed. For Hf, Ta and Zr the use of 40% of copper fluoride as a carrier and of Nb as internal standard provide suitable sensitivities and precissions, while for the rest of elements the best results are obtained with graphite power in different proportions and Rb or Sn as internal standard. (Author). 4 refs

Radiological impact of natural radioactivity in Egyptian phosphate rocks, phosphogypsum and phosphate fertilizers

International Nuclear Information System (INIS)

El-Bahi, S.M.; Sroor, A.; Mohamed, Gehan Y.; El-Gendy, N.S.

2017-01-01

In this study, the activity concentrations of the natural radionuclides in phosphate rocks and its products were measured using a high- purity germanium detector (HPGe). The obtained activity results show remarkable wide variation in the radioactive contents for the different phosphate samples. The average activity concentration of "2"3"5U, "2"3"8U, "2"2"6Ra, "2"3"2Th and "4"0K was found as (45, 1031, 786, 85 and 765 Bq/kg) for phosphate rocks, (28, 1234, 457, 123 and 819 Bq/kg) for phosphate fertilizers, (47, 663, 550, 79 and 870 Bq/kg) for phosphogypsum and (25, 543, 409, 54 and 897 Bq/kg) for single super phosphate respectively. Based on the measured activities, the radiological parameters (activity concentration index, absorbed gamma dose rate in outdoor and indoor and the corresponding annual effective dose rates and total excess lifetime cancer risk) were estimated to assess the radiological hazards. The total excess lifetime cancer risk (ELCR) has been calculated and found to be high in all samples, which related to high radioactivity, representing radiological risk for the health of the population. - Highlights: • Level of radioactivity of phosphate rocks and by-products samples. • The radiological health hazard parameters. • Radiological risk to the health of the population. • The excess lifetime cancer risk factor.

Intermediate Ethanol Blends Catalyst Durability Program

Energy Technology Data Exchange (ETDEWEB)

West, Brian H; Sluder, Scott; Knoll, Keith; Orban, John; Feng, Jingyu

2012-02-01

In the summer of 2007, the U.S. Department of Energy (DOE) initiated a test program to evaluate the potential impacts of intermediate ethanol blends (also known as mid-level blends) on legacy vehicles and other engines. The purpose of the test program was to develop information important to assessing the viability of using intermediate blends as a contributor to meeting national goals for the use of renewable fuels. Through a wide range of experimental activities, DOE is evaluating the effects of E15 and E20 - gasoline blended with 15% and 20% ethanol - on tailpipe and evaporative emissions, catalyst and engine durability, vehicle driveability, engine operability, and vehicle and engine materials. This report provides the results of the catalyst durability study, a substantial part of the overall test program. Results from additional projects will be reported separately. The principal purpose of the catalyst durability study was to investigate the effects of adding up to 20% ethanol to gasoline on the durability of catalysts and other aspects of the emissions control systems of vehicles. Section 1 provides further information about the purpose and context of the study. Section 2 describes the experimental approach for the test program, including vehicle selection, aging and emissions test cycle, fuel selection, and data handling and analysis. Section 3 summarizes the effects of the ethanol blends on emissions and fuel economy of the test vehicles. Section 4 summarizes notable unscheduled maintenance and testing issues experienced during the program. The appendixes provide additional detail about the statistical models used in the analysis, detailed statistical analyses, and detailed vehicle specifications.

Model for blended learning i de tekniske uddannelser

DEFF Research Database (Denmark)

Ringtved, Ulla Lunde; Leth, Lilli-Ann Thomsen; Olsen, Frank

2012-01-01

Anvendelse af blended learning i de tekniske uddannelser i UCN med udgangspunkt i bygningskonstruktøruddannelsen......Anvendelse af blended learning i de tekniske uddannelser i UCN med udgangspunkt i bygningskonstruktøruddannelsen...

Utilization of waste expanded polystyrene: Blends with silica-filled natural rubber

International Nuclear Information System (INIS)

Sekharan, Renju Vaikathusseril; Abraham, Beena Thattekatt; Thachil, Eby Thomas

2012-01-01

Highlights: ► Tensile strength of the silica filled blend is comparable with silica filled NR. ► Modulus and compression set were the best for compatibilized NR/EPS blends. ► Tear strength has increased by 25% for compatibilized blends. ► A 5% waste EPS can be incorporated into NR compounds as a waste management measure. -- Abstract: Expanded polystyrene (EPS) constitutes a considerable part of thermoplastic waste in the environment in terms of volume. In this study, this waste material has been utilized for blending with silica-reinforced natural rubber (NR). The NR/EPS (35/5) blends were prepared by melt mixing in a Brabender Plasticorder. Since NR and EPS are incompatible and immiscible a method has been devised to improve compatibility. For this, EPS and NR were initially grafted with maleic anhydride (MA) using dicumyl peroxide (DCP) to give a graft copolymer. Grafting was confirmed by Fourier Transform Infrared Spectroscopy (FTIR) spectroscopy. This grafted blend was subsequently blended with more of NR during mill compounding. Morphological studies using Scanning Electron Microscopy (SEM) showed better dispersion of EPS in the compatibilized blend compared to the noncompatibilized blend. By this technique, the tensile strength, elongation at break, modulus, tear strength, compression set and hardness of the blend were found to be either at par with or better than that of virgin silica filled NR compound. It is also noted that the thermal properties of the blends are equivalent with that of virgin NR. The study establishes the potential of this method for utilising waste EPS.

Mechanical and thermal properties of physically-blended-plastic films

International Nuclear Information System (INIS)

Abu Issa, M. S.

1983-10-01

Low density polyethylene (LDPE) and isotactic polypropylene (PP) blend were produced in film form and were characterized by a number of techniques such as wide-angle x-ray diffraction (WAXD), differential thermal analysis (DTA), scanning electron microscopy (SEM), and instron tensile testing. Results of WAXD and DTA showed conclusively that the two components in the blend are incompatible. SEM micrographs indicated that the 60/40 and 40/60 PP/PE blends show approximately fine homogeneous dispersion of the minor component into the matrix of the major component. The mechanical properties of the blend films improved with respect to the PE homo polymer. The improvement was more remarkable with the increase of the PP component in the blend. Results obtained in this work were explained in terms of crystallinity and the crystallite orientation. 28 refs., 29 figs., 5 tabs. (A.M.H.)

Perception of blended learning inventory (POBLI) - development and validation

DEFF Research Database (Denmark)

Lassesen, Berit; Rossen, Dorte Sidelmann; Stenalt, Maria Hvid

and explore how the use of blended learning affects teachers’ approaches to teaching and students’ approaches to learning in higher education. So far, there has been relatively limited research on approaches to teaching in blended learning (González 2010; Lameras et al., 2012). In one study, Ellis et al....... In order to identify appropriate uses of blended learning in Higher Education and to enable the tailoring of teaching approaches to the different needs of an increasingly diverse student body, more knowledge is needed on how to integrate blended learning in educational settings and how best to address...... a new strategic focus on 'Educational IT’ with the purpose of strengthening teaching and learning through use of online interactions. Some of the major challenges in the development of this strategy include how to, identify rationales for using blended learning, stimulate pedagogical reflections...

HEU to LEU conversion and blending facility: Oxide blending alternative to produce LEU oxide for commercial use

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This document provides data to be used in the environmental impact analysis for the oxide blending HEU disposition option. This option provides for a yearly HEU throughput of 1 0 metric tons (MT) of uranium metal with an average U235 assay of 50% blended with 165 MT of natural assay triuranium octoxide (U{sub 3} O{sub 8}) per year to produce 177 MT of 4% U235 assay U{sub 3} O{sub 8}, for LWR fuel. Since HEU exists in a variety of forms and not necessarily in the form to be blended, worst case scenarios for preprocessing prior to blending will be assumed for HEU feed streams.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends.

Science.gov (United States)

Ahmed, Khalil

2015-11-01

Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE) compatibilized by Chloroprene rubber (CR) were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr) was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (M L) and maximum torque (M H) of blends increased with increasing weight ratio of HDPE while scorch time (ts2) cure time (tc90), compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends

Directory of Open Access Journals (Sweden)

Khalil Ahmed

2015-11-01

Full Text Available Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE compatibilized by Chloroprene rubber (CR were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (ML and maximum torque (MH of blends increased with increasing weight ratio of HDPE while scorch time (ts2 cure time (tc90, compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties.

Mechanical Properties of Dynamically Vulcanized Thermoplastic Polyurethane (TPU/Polybutadiene Rubber (BR Blends

Directory of Open Access Journals (Sweden)

Ji-Hoo Kim

2017-01-01

Full Text Available To obtain thermoplastic polyurethane (TPU with low hardness, dynamically vulcanized TPU/polybutadiene rubber(BR(70/30 blends were prepared. The effect of dicumyl peroxide (DCP content and stabilizers on the tensile strength and elongation at break of the dynamically vulcanized blends was examined. The tensile strength and elongation at break of the dynamically vulcanized blends decrease with increasing content of DCP. The addition of optimal content of stabilizer leads to the improvement of tensile strength and elongation at break of the blends. Also, the effect of sulfur cure systems and accelerators on the tensile strength and elongation of the blends was investigated. The tensile strength and elongation at break of all the dynamically vulcanized TPU/BR (70/30 blends using 1-step processing are not higher than those of simple TPU/BR (70/30 blends. However, the tensile strength and elongation of the dynamically vulcanized blends prepared at 8 min (mixing time using 2-step processing are higher than those of the simple blends.

A Study on Students’ Views On Blended Learning Environment

Directory of Open Access Journals (Sweden)

Meryem YILMAZ SOYLU

2006-07-01

Full Text Available In the 21st century, information and communication technologies (ICT have developed rapidly and influenced most of the fields and education as well. Then, ICT have offered a favorable environment for the development and use of various methods and tools. With the developments in technology, blended learning has gained considerable popularity in recent years. Together with the developments it brought along the description of particular forms of teaching with technology. Blended learning is defined simply as a learning environment that combines technology with face-to-face learning. In other words blended learning means using a variety of delivery methods to best meet the course objectives by combining face-to-face teaching in a traditional classroom with teaching online. This article examines students’ views on blended learning environment. The study was conducted on 64 students from Department of Computer Education and Instructional Technologies in 2005–2006 fall semester in Instructional Design and Authoring Languages in PC Environment at Hacettepe University. The results showed that the students enjoyed taking part in the blended learning environment. Students’ achievement levels and their frequency of participation to forum affected their views about blended learning environment. Face-to-face interaction in blended learning application had the highest score. This result demonstrated the importance of interaction and communication for the success of on-line learning.

Meeting Diverse Learner Needs with Blended Learning

Science.gov (United States)

Owen, Hazel

2010-01-01

This article describes a 40-week Computer, Research Skills, and Projects (CRSP) blended learning course designed and implemented at Dubai Men's College. The learning employed a design using socio-constructivist principles in the blended approach to cater to the learning preferences of students. (Contains 2 figures and 1 footnote.)

Effects of blending on the properties of diesel and palm biodiesel

Science.gov (United States)

Bukkarapu, Kiran Raj; Srinivas Rahul, T.; Kundla, Sivaji; Vishnu Vardhan, G.

2018-03-01

Palm biodiesel is blended to diesel in different volume percentages to improve certain properties. This would help in having a good understanding of the dependence of the diesel properties on the biodiesel proportion. The properties of interest in the present work are density, kinematic viscosity, flash point and fire point of the blends which are determined and compared to petrodiesel. It is observed that the kinematic viscosity and density of the diesel increase with the palm biodiesel proportion and it is not preferable. Blends with higher palm content possess higher flash point and fire point. Apparently, blending worsens the conditions and hence might be of no use when compared to diesel, but when compared to neat palm biodiesel, blending helped in pulling down the density, viscosity, fire point and flash point of the latter. Using regression analysis and the properties data of respective blends, correlations are developed to predict the properties of diesel and biodiesel blends known the percentage of biodiesel added to diesel, which are validated using biodiesel and diesel blends which are not used as an input to develop them.

Thermoset Blends of an Epoxy Resin and Polydicyclopentadiene

Energy Technology Data Exchange (ETDEWEB)

Rohde, Brian J.; Le, Kim Mai; Krishnamoorti, Ramanan; Robertson, Megan L.

2016-12-13

The mechanical properties of two chemically distinct and complementary thermoset polymers were manipulated through development of thermoset blends. The thermoset blend system was composed of an anhydride-cured diglycidyl ether of bisphenol A (DGEBA)-based epoxy resin, contributing high tensile strength and modulus, and polydicyclopentadiene (PDCPD), which has a higher toughness and impact strength as compared to other thermoset polymers. Ultra-small-angle and small-angle X-ray scattering analysis explored the morphology of concurrently cured thermoset blends, revealing a macroscopically phase separated system with a surface fractal structure across blended systems of varying composition. The epoxy resin rich and PDCPD rich phases exhibited distinct glass transitions (Tg’s): the Tg observed at higher temperature was associated with the epoxy resin rich phase and was largely unaffected by the presence of PDCPD, whereas the PDCPD rich phase Tg systematically decreased with increasing epoxy resin content due to inhibition of dicyclopentadiene ring-opening metathesis polymerization. The mechanical properties of these phase-separated blends were in reasonable agreement with predictions by the rule of mixtures for the blend tensile strength, modulus, and fracture toughness. Scanning electron microscopy analysis of the tensile and fracture specimen fracture surfaces showed an increase in energy dissipation mechanisms, such as crazing, shear banding, and surface roughness, as the fraction of the more ductile component, PDPCD, increased. These results present a facile method to tune the mechanical properties of a toughened thermoset network, in which the high modulus and tensile strength of the epoxy resin can be largely retained at high epoxy resin content in the blend, while increasing the fracture toughness.

Proton exchange membranes based on PVDF/SEBS blends

Energy Technology Data Exchange (ETDEWEB)

Mokrini, A.; Huneault, M.A. [Industrial Materials Institute, National Research Council of Canada, 75 de Mortagne Blvd., Boucherville, Que. (Canada J4B 6Y4)

2006-03-09

Proton-conductive polymer membranes are used as an electrolyte in the so-called proton exchange membrane fuel cells. Current commercially available membranes are perfluorosulfonic acid polymers, a class of high-cost ionomers. This paper examines the potential of polymer blends, namely those of styrene-(ethylene-butylene)-styrene block copolymer (SEBS) and polyvinylidene fluoride (PVDF), in the proton exchange membrane application. SEBS/PVDF blends were prepared by twin-screw extrusion and the membranes were formed by calendering. SEBS is a phase-segregated material where the polystyrene blocks can be selectively functionalized offering high ionic conductivity, while PVDF insures good dimensional stability and chemical resistance to the films. Proton conductivity of the films was obtained by solid-state grafting of sulfonic acid moieties. The obtained membranes were characterized in terms of conductivity, ionic exchange capacity and water uptake. In addition, the membranes were characterized in terms of morphology, microstructure and thermo-mechanical properties to establish the blends morphology-property relationships. Modification of interfacial properties between SEBS and PVDF was found to be a key to optimize the blends performance. Addition of a methyl methacrylate-butyl acrylate-methyl methacrylate block copolymer (MMA-BA-MMA) was found to compatibilize the blend by reducing the segregation scale and improving the blend homogeneity. Mechanical resistance of the membranes was also improved through the addition of this compatibilizer. As little as 2wt.% compatibilizer was sufficient for complete interfacial coverage and lead to improved mechanical properties. Compatibilized blend membranes also showed higher conductivities, 1.9x10{sup -2} to 5.5x10{sup -3}Scm{sup -1}, and improved water management. (author)

SYSTEM APPROACH TO THE BLENDED LEARNING

Directory of Open Access Journals (Sweden)

Vladimir Kukharenko

2015-10-01

Full Text Available Currently, much attention is paid to the development of learning sour cream – a combination of traditional and distance (30-70% of training. Such training is sometimes called hybrid and referred to disruptive technologies. Purpose – to show that the use of systemic campaign in blended learning provides a high quality of education, and the technology can be devastating. The subject of the study – blended learning, object of study – Mixed learning process. The analysis results show that the combined training increases the motivation of students, qualification of teachers, personalized learning process. At the same time there are no reliable methods of assessing the quality of education and training standards. It is important that blended learning strategy to support the institutional goals and had an effective organizational model for support.

Phase Segregation in Polystyrene?Polylactide Blends

Energy Technology Data Exchange (ETDEWEB)

Leung, Bonnie; Hitchcock, Adam; Brash, John; Scholl, Andreas; Doran, Andrew

2010-06-09

Spun-cast films of polystyrene (PS) blended with polylactide (PLA) were visualized and characterized using atomic force microscopy (AFM) and synchrotron-based X-ray photoemission electron microscopy (X-PEEM). The composition of the two polymers in these systems was determined by quantitative chemical analysis of near-edge X-ray absorption signals recorded with X-PEEM. The surface morphology depends on the ratio of the two components, the total polymer concentration, and the temperature of vacuum annealing. For most of the blends examined, PS is the continuous phase with PLA existing in discrete domains or segregated to the air?polymer interface. Phase segregation was improved with further annealing. A phase inversion occurred when films of a 40:60 PS:PLA blend (0.7 wt percent loading) were annealed above the glass transition temperature (Tg) of PLA.

Calcium phosphates: what is the evidence?

Science.gov (United States)

Larsson, Sune

2010-03-01

A number of different calcium phosphate compounds such as calcium phosphate cements and solid beta-tricalcium phosphate products have been introduced during the last decade. The chemical composition mimics the mineral phase of bone and as a result of this likeness, the materials seem to be remodeled as for normal bone through a cell-mediated process that involves osteoclastic activity. This is a major difference when compared with, for instance, calcium sulphate compounds that after implantation dissolve irrespective of the new bone formation rate. Calcium phosphates are highly biocompatible and in addition, they act as synthetic osteoconductive scaffolds after implantation in bone. When placed adjacent to bone, osteoid is formed directly on the surface of the calcium phosphate with no soft tissue interposed. Remodeling is slow and incomplete, but by adding more and larger pores, like in ultraporous beta-tricalcium phosphate, complete or nearly complete resorption can be achieved. The indications explored so far include filling of metaphyseal fracture voids or bone cysts, a volume expander in conjunction with inductive products, and as a carrier for various growth factors and antibiotics. Calcium phosphate compounds such as calcium phosphate cement and beta-tricalcium phosphate will most certainly be part of the future armamentarium when dealing with fracture treatment. It is reasonable to believe that we have so far only seen the beginning when it comes to clinical applications.

Structural characterization of Poly aniline blended with polyacrylamide

International Nuclear Information System (INIS)

Fayek, S.A.; El-Sayed, S.M.; Sayed, W.M.

2007-01-01

Poly aniline / polyacrylamide blends in presence of different catalysts were prepared. X-ray diffraction studies reveal that the samples produced are crystalline. Optical gap of the blend in the presence of NaCIO 4 used as a catalyst is greater than that in the presence of (NH 4 ) 2 S 2 O 8 as a catalyst. The structure of polyacrylamide (PAM) blended with poly aniline (PANI) were investigated by infrared spectroscopy, Grain size was identified using scanning electron microscopy [SEM

Preparation and Characterization of Keratin/Alginate Blend Microparticles

OpenAIRE

Srisuwan, Yaowalak; Srihanam, Prasong

2018-01-01

The water-in-oil (W/O) emulsification-diffusion method was used for construction of keratin (Ker), alginate (Alg), and Ker/Alg blend microparticles. The Ker, Alg, and Ker/Alg blend solutions were used as the water phase, while ethyl acetate was used as the oil phase. Firstly, different concentrations of Ker solution was used to find suitable content. 1.6% w/v Ker solution was blended with the same concentration of the Alg solution for further microparticle construction. Results from scanning ...

Flippin' Fluid Mechanics - Comparison of Blended Classroom vs. Traditional Lecture

Science.gov (United States)

Webster, D. R.; Kadel, R. S.; Newstetter, W. C.

2017-11-01

We conducted a study of student performance in and perceptions of a blended classroom delivery of a junior-level fluid mechanics course. In the blended pedagogy, students watch short on-line videos before class, participate in interactive in-class problem solving (in dyads), and complete individualized on-line quizzes weekly. Comparisons are made among four sections of the blended classroom delivery in the period of 2013-2017 to eleven sections delivered in a traditional lecture-style format by the same instructor in 2002-2012. The results reveal dramatic improvement in student engagement, perceptions, and achievement in the blended pedagogy. For instance, the withdrawal/fail/barely-passing (WFD) rate is significantly lower for the blended classroom (8.6% vs. 16.3%; p self-perception of how-much-learned, perception of the value of the course activities, and the overall effectiveness of the course and instructor in the blended classroom.

Influence of biodiesel blending on physicochemical properties and importance of mathematical model for predicting the properties of biodiesel blend

International Nuclear Information System (INIS)

Wakil, M.A.; Kalam, M.A.; Masjuki, H.H.; Atabani, A.E.; Rizwanul Fattah, I.M.

2015-01-01

Highlights: • Short identification of selected biodiesel feedstock. • Review of physicochemical properties for blended biodiesel. • Mathematical model for predicting properties of various biodiesel blends. - Abstract: The growing demand for green world serves as one of the most significant challenges of modernization. Requirements like largest usage of energy for modern society as well as demand for friendly milieu create a deep concern in field of research. Biofuels are placed at the peak of the research arena for their underlying benefits as mentioned by multiple researches. Out of a number of vegetable oils, only a few are used commercially for biodiesel production. Due to various limitations of edible oil, non-edible oils are becoming a profitable choice. Till today, very little percentage of biodiesel is used successfully in engine. The research is still continuing for improving the biodiesel usage level. Recently, it is found that the blended biodiesel from more than one feedstock provides better performance in engine. This paper reviews the physicochemical properties of different biodiesel blends obtained from various feedstocks with a view to properly understand the fuel quality. Moreover, a short description of each feedstock is given along with graphical presentation of important properties for various blend percentages from B0 to B100. Finally, mathematical model is formed for predicting various properties of biodiesel blend with the help of different research data by using polynomial curve fitting method. The results obtained from a number of literature based on this work shows that the heating value of biodiesel is about 11% lower than diesel except coconut (14.5% lower) whereas kinematic viscosity is in the range of 4–5.4 mm 2 /s. Flash point of all biodiesels are more than 150 °C, except neem and coconut. Cold flow properties of calophyllum, palm, jatropha, moringa are inferior to others. This would help to determine important properties of

X-ray blending device

International Nuclear Information System (INIS)

Manolov, S.S.; Donchev, I.D.; Paunchev, A.N.; Atanasov, A.B.; Kerin, T.P.

1985-01-01

The X-ray blending device comprises electric motors for vertical and horizontal blending plates, electrically connected with the output of the block for format voltages and mechanically connected with the measuring potentiometers' slides. The potentiometers are respectively connected with the data inputs of the block for format voltages, the control input of which is connected with the control block output in a mode of scanning. The data outputs of the format voltage block are connected through a buffer converter, a memory block and a decoder with the data inputs of the first and second digital-to-analog converters, the outputs of which are connected with the first inputs of the first and the second comparison circuits. The second inputs of the last are linked to the slides of the first and the second potentiometers and their inputs are connected with the data inputs of the first and the second combinational logic circuits. The output of the control block in a mode of scanning is connected with the first control inputs of the first and the second combinational logic circuits and with the control inputs of the memory block and the decoder. The second and the third control units of the first and the second combinational circuits are respectively linked with the outputs for a position determination of the vertical and horizontal blending plates from the control block in a mode of scanning. The outputs of the first and the second combinational logic circuits are respectively connected with the first and the second control bridge circuits, the control outputs of which are electrically connected with the first and the second electric motors for vertical and horizontal blending plates. 1 cl., 3 figs

COOLING COIL EFFECTS ON BLENDING IN A PILOT SCALE TANK

International Nuclear Information System (INIS)

Leishear, R.; Poirier, M.; Fowley, M.; Steeper, T.

2010-01-01

Blending, or mixing, processes in 1.3 million gallon nuclear waste tanks are complicated by the fact that miles of serpentine, vertical, cooling coils are installed in the tanks. As a step toward investigating blending interference due to coils in this type of tank, a 1/10.85 scale tank and pump model were constructed for pilot scale testing. A series of tests were performed in this scaled tank by adding blue dye to visualize blending, and by adding acid or base tracers to solution to quantify the time required to effectively blend the tank contents. The acid and base tests were monitored with pH probes, which were located in the pilot scale tank to ensure that representative samples were obtained. Using the probes, the hydronium ion concentration [H + ] was measured to ensure that a uniform concentration was obtained throughout the tank. As a result of pilot scale testing, a significantly improved understanding of mixing, or blending, in nuclear waste tanks has been achieved. Evaluation of test data showed that cooling coils in the waste tank model increased pilot scale blending times by 200% in the recommended operating range, compared to previous theoretical estimates of a 10-50% increase. Below the planned operating range, pilot scale blending times were increased by as much as 700% in a tank with coils installed. One pump, rather than two or more, was shown to effectively blend the tank contents, and dual pump nozzles installed parallel to the tank wall were shown to provide optimal blending. In short, experimental results varied significantly from expectations.

Sensitivity comparison of two L-alanine doped blends to different photon energies

International Nuclear Information System (INIS)

Chen, Felipe; Vega Ramirez, Jose; Nicolucci, Patricia; Baffa, Oswaldo

2008-01-01

Full text: Blends of L-alanine (85% weight proportion) with KI (10%) and with PbI 2 (10%), these last two compounds acting as dopants, and with PVA (5%) acting as binder, were prepared in water at 80 C degrees. A blend of pure L-alanine (95%) with PVA (5%) was also prepared. The three blends were irradiated with photon beams of different energies (120 kV, 60 Co and 10 MV) with a unique dose of 30 Gy to compare their sensitivities for those three energies. EPR spectra of the three irradiated blends were recorded in a K-Band spectrometer (24 GHz) taking aliquots of about 4 mg for each blend. The energy sensitivity of a blend was defined as the peak-to-peak amplitude of its EPR spectrum central line. For the 60 Co energy (1.25 MeV) the blends presented practically the same sensitivity indicating that the presence of the dopants does not affect the sensitivity of L-alanine. For 10 MV X-rays there was an increment (around 20% - 30 %) in sensitivity for the two L-alanine doped blends compared with the pure L-alanine blend (not doped). In the case of 120 kV X-rays, the blends ala+KI and ala+PbI 2 showed an increment of 10 and 20 times, respectively, more sensitivity than the pure L-alanine blend. It is concluded that the dopants KI and PbI 2 produce a great enhance of the L-alanine sensitivity to low-energy photons. For the same dopant's content (10%) in the blend, PbI 2 showed a better performance. These results encourage us to try to enhance the sensitivity of L-alanine even more increasing the dopant's content in the blend. Application of these L-alanine doped blends in the dosimetry in diagnostic radiology could be possible. (author)

Poly(hydroxybutyrate)/cellulose acetate blend nanofiber scaffolds: Preparation, characterization and cytocompatibility

Energy Technology Data Exchange (ETDEWEB)

Zhijiang, Cai, E-mail: caizhijiang@hotmail.com [School of Textiles, Tianjin Polytechnic University, Tianjin 300387 (China); State Key Laboratory of Hollow Fiber Membrane Material and Processes, No 399 BingShuiXi Street, XiQing District, Tianjin, China, 300387 (China); Yi, Xu; Haizheng, Yang; Jia, Jianru; Liu, Yuanpei [School of Textiles, Tianjin Polytechnic University, Tianjin 300387 (China)

2016-01-01

Poly(hydroxybutyrate) (PHB)/cellulose acetate (CA) blend nanofiber scaffolds were fabricated by electrospinning using the blends of chloroform and DMF as solvent. The blend nanofiber scaffolds were characterized by SEM, FTIR, XRD, DSC, contact angle and tensile test. The blend nanofibers exhibited cylindrical, uniform, bead-free and random orientation with the diameter ranged from 80–680 nm. The scaffolds had very well interconnected porous fibrous network structure and large aspect surface areas. It was found that the presence of CA affected the crystallization of PHB due to formation of intermolecular hydrogen bonds, which restricted the preferential orientation of PHB molecules. The DSC result showed that the PHB and CA were miscible in the blend nanofiber. An increase in the glass transition temperature was observed with increasing CA content. Additionally, the mechanical properties of blend nanofiber scaffolds were largely influenced by the weight ratio of PHB/CA. The tensile strength, yield strength and elongation at break of the blend nanofiber scaffolds increased from 3.3 ± 0.35 MPa, 2.8 ± 0.26 MPa, and 8 ± 0.77% to 5.05 ± 0.52 MPa, 4.6 ± 0.82 MPa, and 17.6 ± 1.24% by increasing PHB content from 60% to 90%, respectively. The water contact angle of blend nanofiber scaffolds decreased about 50% from 112 ± 2.1° to 60 ± 0.75°. The biodegradability was evaluated by in vitro degradation test and the results revealed that the blend nanofiber scaffolds showed much higher degradation rates than the neat PHB. The cytocompatibility of the blend nanofiber scaffolds was preliminarily evaluated by cell adhesion studies. The cells incubated with PHB/CA blend nanofiber scaffold for 48 h were capable of forming cell adhesion and proliferation. It showed much better biocompatibility than pure PHB film. Thus, the prepared PHB/CA blend nanofiber scaffolds are bioactive and may be more suitable for cell proliferation suggesting that these scaffolds can be used for

Preparing Teachers for Emerging Blended Learning Environments

Science.gov (United States)

Oliver, Kevin M.; Stallings, Dallas T.

2014-01-01

Blended learning environments that merge learning strategies, resources, and modes have been implemented in higher education settings for nearly two decades, and research has identified many positive effects. More recently, K-12 traditional and charter schools have begun to experiment with blended learning, but to date, research on the effects of…

Supertoughened renewable PLA reactive multiphase blends system: phase morphology and performance.

Science.gov (United States)

Zhang, Kunyu; Nagarajan, Vidhya; Misra, Manjusri; Mohanty, Amar K

2014-08-13

Multiphase blends of poly(lactic acid) (PLA), ethylene-methyl acrylate-glycidyl methacrylate (EMA-GMA) terpolymer, and a series of renewable poly(ether-b-amide) elastomeric copolymer (PEBA) were fabricated through reactive melt blending in an effort to improve the toughness of the PLA. Supertoughened PLA blend showing impact strength of ∼500 J/m with partial break impact behavior was achieved at an optimized blending ratio of 70 wt % PLA, 20 wt % EMA-GMA, and 10 wt % PEBA. Miscibility and thermal behavior of the binary blends PLA/PEBA and PLA/EMA-GMA, and the multiphase blends were also investigated through differential scanning calorimetric (DSC) and dynamic mechanical analysis (DMA). Phase morphology and fracture surface morphology of the blends were studied through scanning electron microscopy (SEM) and atomic force microscopy (AFM) to understand the strong corelation between the morphology and its significant effect on imparting tremendous improvement in toughness. A unique "multiple stacked structure" with partial encapsulation of EMA-GMA and PEBA minor phases was observed for the PLA/EMA-GMA/PEBA (70/20/10) revealing the importance of particular blend composition in enhancing the toughness. Toughening mechanism behind the supertoughened PLA blends have been established by studying the impact fractured surface morphology at different zones of fracture. Synergistic effect of good interfacial adhesion and interfacial cavitations followed by massive shear yielding of the matrix was believed to contribute to the enormous toughening effect observed in these multiphase blends.

Emissions from Ethanol-Gasoline Blends: A Single Particle Perspective

Directory of Open Access Journals (Sweden)

Peter H. McMurry

2011-06-01

Full Text Available Due to its agricultural origin and function as a fuel oxygenate, ethanol is being promoted as an alternative biomass-based fuel for use in spark ignition engines, with mandates for its use at state and regional levels. While it has been established that the addition of ethanol to a fuel reduces the particulate mass concentration in the exhaust, little attention has been paid to changes in the physicochemical properties of the emitted particles. In this work, a dynamometer-mounted GM Quad-4 spark ignition engine run without aftertreatment at 1,500 RPM and 100% load was used with four different fuel blends, containing 0, 20, 40 and 85 percent ethanol in gasoline. This allowed the effects of the fuel composition to be isolated from other effects. Instrumentation employed included two Aerosol Time-of-Flight Mass Spectrometers covering different size ranges for analysis of single particle composition, an Aethalometer for black carbon, a Scanning Mobility Particle Sizer for particle size distributions, a Photoelectric Aerosol Sensor for particle-bound polycyclic aromatic hydrocarbon (PAH species and gravimetric filter measurements for particulate mass concentrations. It was found that, under the conditions investigated here, additional ethanol content in the fuel changes the particle size distribution, especially in the accumulation mode, and decreases the black carbon and total particulate mass concentrations. The molecular weight distribution of the PAHs was found to decrease with added ethanol. However, PAHs produced from higher ethanol-content fuels are associated with NO2− (m/z—46 in the single-particle mass spectra, indicating the presence of nitro-PAHs. Compounds associated with the gasoline (e.g., sulfur-containing species are diminished due to dilution as ethanol is added to the fuel relative to those associated with the lubricating oil (e.g., calcium, zinc, phosphate in the single particle spectra. These changes have potential

Blended Interaction Spaces for Collaborative Design

DEFF Research Database (Denmark)

Dalsgaard, Peter; Halskov, Kim; Klokmose, Clemens Nylandsted

During the past five years, we have explored the use, potentials and challenges of Blended Interaction spaces. In addition, we have a long background in developing and exploring methods for collaborative design. In this workshop paper, we give an overview of our work and present our visions...... and ongoing research in developing Blended Interaction spaces for collaborative design. We then identify key themes and challenges pertinent for the workshop....

Inkjet-Printed Organic Transistors Based on Organic Semiconductor/Insulating Polymer Blends.

Science.gov (United States)

Kwon, Yoon-Jung; Park, Yeong Don; Lee, Wi Hyoung

2016-08-02

Recent advances in inkjet-printed organic field-effect transistors (OFETs) based on organic semiconductor/insulating polymer blends are reviewed in this article. Organic semiconductor/insulating polymer blends are attractive ink candidates for enhancing the jetting properties, inducing uniform film morphologies, and/or controlling crystallization behaviors of organic semiconductors. Representative studies using soluble acene/insulating polymer blends as an inkjet-printed active layer in OFETs are introduced with special attention paid to the phase separation characteristics of such blended films. In addition, inkjet-printed semiconducting/insulating polymer blends for fabricating high performance printed OFETs are reviewed.

HIGH SCHOOL STUDENTS’ VIEWS ON BLENDED LEARNING

Directory of Open Access Journals (Sweden)

Ibrahim Umit YAPICI,

2012-08-01

Full Text Available In this study, it is aimed to determine the high school students’ views on blended learning. The study was carried out in biology course for the lesson unit of “Classification of Living Things and Biodiversity” with 47 9th grade students attending Nevzat Ayaz Anatolian High School in the second term of the academic year of 2009-2010. The lessons were taught in a way appropriate to the blended learning model both via the Internet and on face-to-face basis. As the online dimension of the blended learning model, Moodle, a Learning Management System (LMS, was used. The application lasted 10 weeks. The scale of learners’ views on blended learning was applied and interviews were held to determine the views. As a result of the analysis of the scale, it was seen that their views were “highly” positive. The interviews held with the students revealed that the blended learning model provided students with various opportunities such as getting prepared for the lessons, reviewing the lessons as many times as wanted, reaching the subject-related materials without being dependent on time and place, testing oneself and communicating with the teacher and other students out of the school. The interviews also revealed that there were various problems though such as lack of Internet connection at home and problems experienced while playing the videos.

Biocompatible electrospun polymer blends for biomedical applications.

Science.gov (United States)

Munj, Hrishikesh Ramesh; Nelson, M Tyler; Karandikar, Prathamesh Sadanand; Lannutti, John Joseph; Tomasko, David Lane

2014-10-01

Blends of natural and synthetic polymers have received considerable attention as biomaterials due to the potential to optimize both mechanical and bioactive properties. Electrospinning of biocompatible polymers is an efficient method producing biomimetic topographies suited to various applications. In the ultimate application, electrospun scaffolds must also incorporate drug/protein delivery for effective cell growth and tissue repair. This study explored the suitability of a ternary Polymethylmethacrylate-Polycaprolactone-gelatin blend in the preparation of electrospun scaffolds for biomedical applications. Tuning the blend composition allows control over scaffold mechanical properties and degradation rate. Significant improvements were observed in the mechanical properties of the blend compared with the individual components. In order to study drug delivery potential, triblends were impregnated with the model compound Rhodamine-B using sub/supercritical CO₂ infusion under benign conditions. Results show significantly distinct release profiles of the impregnated dye from the triblends. Specific factors such as porosity, degradation rate, stress relaxation, dye-polymer interactions, play key roles in impregnation and release. Each polymer component of the triblends shows distinct behavior during impregnation and release process. This affects the aforementioned factors and the release profiles of the dye. Careful control over blend composition and infusion conditions creates the flexibility needed to produce biocompatible electrospun scaffolds for a variety of biomedical applications. © 2014 Wiley Periodicals, Inc.

Phosphate additives in food--a health risk.

Science.gov (United States)

Ritz, Eberhard; Hahn, Kai; Ketteler, Markus; Kuhlmann, Martin K; Mann, Johannes

2012-01-01

Hyperphosphatemia has been identified in the past decade as a strong predictor of mortality in advanced chronic kidney disease (CKD). For example, a study of patients in stage CKD 5 (with an annual mortality of about 20%) revealed that 12% of all deaths in this group were attributable to an elevated serum phosphate concentration. Recently, a high-normal serum phosphate concentration has also been found to be an independent predictor of cardiovascular events and mortality in the general population. Therefore, phosphate additives in food are a matter of concern, and their potential impact on health may well have been underappreciated. We reviewed pertinent literature retrieved by a selective search of the PubMed and EU databases (www.zusatzstoffe-online.de, www.codexalimentarius.de), with the search terms "phosphate additives" and "hyperphosphatemia." There is no need to lower the content of natural phosphate, i.e. organic esters, in food, because this type of phosphate is incompletely absorbed; restricting its intake might even lead to protein malnutrition. On the other hand, inorganic phosphate in food additives is effectively absorbed and can measurably elevate the serum phosphate concentration in patients with advanced CKD. Foods with added phosphate tend to be eaten by persons at the lower end of the socioeconomic scale, who consume more processed and "fast" food. The main pathophysiological effect of phosphate is vascular damage, e.g. endothelial dysfunction and vascular calcification. Aside from the quality of phosphate in the diet (which also requires attention), the quantity of phosphate consumed by patients with advanced renal failure should not exceed 1000 mg per day, according to the guidelines. Prospective controlled trials are currently unavailable. In view of the high prevalence of CKD and the potential harm caused by phosphate additives to food, the public should be informed that added phosphate is damaging to health. Furthermore, calls for labeling

The combustion of coal blends in a fluidised bed reactor

Energy Technology Data Exchange (ETDEWEB)

Boavida, Dulce; Abelha, Pedro; Gulyurtlu, Ibrahim; Cabrita, Isabel

1999-07-01

Combustion studies of five coals of different origin were carried out in a laboratory scale fluidised bed combustor. Five blends prepared by mixing two coals based on their petrological characterisation, in varying amounts, were selected to study the possibility of reduction NO{sub x}, N{sub 2}O and SO{sub 2} emissions. The results showed that some blends had the opposite behaviour concerning the release of NO{sub x} and SO{sub 2} in relation to parent coals, and the emissions were higher than expected. The N{sub 2}O amounts observed were, however, in almost all blends tested, lower than predicted values. With some blends, the mixing levels intended to reduce SO{sub 2} were not always found to correspond to those for simultaneous decrease of Nox. Most of the blends studied showed some evidence of interaction between them. Varying the proportion of the blend components was observed to alter the temperatures at which interactions were stronger.

Oxidative stability of diacylglycerol oil and butter blends containing diacylglycerols

DEFF Research Database (Denmark)

Kristensen, Janni Brogaard; Nielsen, Nina Skall; Jacobsen, Charlotte

2006-01-01

Diacylglycerol (DAG) oils produced from sunflower oil and traditional sunflower oil were stored for 20 wk at 38 degrees C, and their oxidative stability was measured. Moreover, two butter blends were produced containing 40 wt-% DAG oil made from sunflower oil or rapeseed oil, respectively, as well...... as two control butter blends with sunflower oil or rapeseed oil. Their oxidative stability during storage at 5 degrees C for up to 12 wk was examined by similar means as for the pure oils. The storage study of the oils indicated that the DAG oil was oxidatively less stable as compared to sunflower oil......, but that they had similar sensory quality. Storage of the butter blends revealed that blends with the two types of rapeseed oil (triacylglycerol (TAG) or DAG oil) were oxidatively more stable than the blends containing oils from sunflower. There was no unambiguous indication of DAG butter blends having a different...

Olivine-Based Blended Compounds as Positive Electrodes for Lithium Batteries

Directory of Open Access Journals (Sweden)

Christian M. Julien

2016-05-01

Full Text Available Blended cathode materials made by mixing LiFePO4 (LFP with LiMnPO4 (LMP or LiNi1/3Mn1/3Co1/3O2 (NMC that exhibit either high specific energy and high rate capability were investigated. The layered blend LMP–LFP and the physically mixed blend NMC–LFP are evaluated in terms of particle morphology and electrochemical performance. Results indicate that the LMP–LFP (66:33 blend has a better discharge rate than the LiMn1−yFeyPO4 with the same composition (y = 0.33, and NMC–LFP (70:30 delivers a remarkable stable capacity over 125 cycles. Finally, in situ voltage measurement methods were applied for the evaluation of the phase evolution of blended cathodes and gradual changes in cell behavior upon cycling. We also discuss through these examples the promising development of blends as future electrodes for new generations of Li-ion batteries.

Blended Learning Versus Traditional Lecture in Introductory Nursing Pathophysiology Courses.

Science.gov (United States)

Blissitt, Andrea Marie

2016-04-01

Currently, many undergraduate nursing courses use blended-learning course formats with success; however, little evidence exists that supports the use of blended formats in introductory pathophysiology courses. The purpose of this study was to compare the scores on pre- and posttests and course satisfaction between traditional and blended course formats in an introductory nursing pathophysiology course. This study used a quantitative, quasi-experimental, nonrandomized control group, pretest-posttest design. Analysis of covariance compared pre- and posttest scores, and a t test for independent samples compared students' reported course satisfaction of the traditional and blended course formats. Results indicated that the differences in posttest scores were not statistically significant between groups. Students in the traditional group reported statistically significantly higher satisfaction ratings than students in the blended group. The results of this study support the need for further research of using blended learning in introductory pathophysiology courses in undergraduate baccalaureate nursing programs. Further investigation into how satisfaction is affected by course formats is needed. Copyright 2016, SLACK Incorporated.

Design of tailor-made chemical blend using a decomposition-based computer-aided approach

DEFF Research Database (Denmark)

Yunus, Nor Alafiza; Gernaey, Krist; Manan, Z.A.

2011-01-01

Computer aided techniques form an efficient approach to solve chemical product design problems such as the design of blended liquid products (chemical blending). In chemical blending, one tries to find the best candidate, which satisfies the product targets defined in terms of desired product...... methodology for blended liquid products that identifies a set of feasible chemical blends. The blend design problem is formulated as a Mixed Integer Nonlinear Programming (MINLP) model where the objective is to find the optimal blended gasoline or diesel product subject to types of chemicals...... and their compositions and a set of desired target properties of the blended product as design constraints. This blend design problem is solved using a decomposition approach, which eliminates infeasible and/or redundant candidates gradually through a hierarchy of (property) model based constraints. This decomposition...

Enhancing Students' Language Skills through Blended Learning

Science.gov (United States)

Banditvilai, Choosri

2016-01-01

This paper presents a case study of using blended learning to enhance students' language skills and learner autonomy in an Asian university environment. Blended learning represents an educational environment for much of the world where computers and the Internet are readily available. It combines self-study with valuable face-to-face interaction…

Blended Learning in Personalized Assistive Learning Environments

Science.gov (United States)

Marinagi, Catherine; Skourlas, Christos

2013-01-01

In this paper, the special needs/requirements of disabled students and cost-benefits for applying blended learning in Personalized Educational Learning Environments (PELE) in Higher Education are studied. The authors describe how blended learning can form an attractive and helpful framework for assisting Deaf and Hard-of-Hearing (D-HH) students to…

Phosphate analysis of natural sausage casings preserved in brines with phosphate additives as inactivating agent - Method validation.

Science.gov (United States)

Wijnker, J J; Tjeerdsma-van Bokhoven, J L M; Veldhuizen, E J A

2009-01-01

Certain phosphates have been identified as suitable additives for the improvement of the microbial and mechanical properties of processed natural sausage casings. When mixed with NaCl (sodium chloride) and used under specific treatment and storage conditions, these phosphates are found to prevent the spread of foot-and-mouth disease and classical swine fever via treated casings. The commercially available Quantichrom™ phosphate assay kit has been evaluated as to whether it can serve as a reliable and low-tech method for routine analysis of casings treated with phosphate. The outcome of this study indicates that this particular assay kit has sufficient sensitivity to qualitatively determine the presence of phosphate in treated casings without interference of naturally occurring phosphate in salt used for brines in which casings are preserved.

Characterization of a calcium phosphate cement based on alpha-tricalcium phosphate obtained by wet precipitation process

International Nuclear Information System (INIS)

Thurmer, M.B.; Diehl, C.E.; Vieira, R.S.; Coelho, W.T.G.; Santos, L.A.

2012-01-01

There are several systems of calcium phosphate cements being studied. Those based on alpha-tricalcium phosphate are of particular interest. After setting they produce calcium deficient hydroxyapatite similar to bone like hydroxyapatite. This work aims to obtain alpha-tricalcium phosphate powders by the wet precipitation process, using calcium nitrate and phosphoric acid as reagents. This powder was characterized by infrared spectroscopy, X-ray diffraction and particle size distribution. In order to prepare the calcium phosphate cement, the powder was mixed with an accelerator in an aqueous solution. The mechanical properties of the cement were assessed and it was evaluated by means of apparent density, X-ray diffraction and scanning electron microscopy. The described method produced crystalline alpha-tricalcium phosphate as the major phase. The calcium phosphate cement showed high values of compression strength (50 MPa). The soaking of the cement in a simulated body fluid (SBF) formed a layer of hydroxyapatite like crystals in the surface of the samples. (author)

Phosphate solubilization and multiple plant growth promoting ...

African Journals Online (AJOL)

Phosphate solubilizing efficiencies of the strains were analyzed using different insoluble phosphorus sources and the results show that most isolates released a substantial amount of soluble phosphate from tricalcium phosphate, rock phosphate and bone meal. Screening for multiple plant growth promoting attributes ...

Degradable polyphosphazene/poly(alpha-hydroxyester) blends: degradation studies.

Science.gov (United States)

Ambrosio, Archel M A; Allcock, Harry R; Katti, Dhirendra S; Laurencin, Cato T

2002-04-01

Biomaterials based on the polymers of lactic acid and glycolic acid and their copolymers are used or studied extensively as implantable devices for drug delivery, tissue engineering and other biomedical applications. Although these polymers have shown good biocompatibility, concerns have been raised regarding their acidic degradation products, which have important implications for long-term implantable systems. Therefore, we have designed a novel biodegradable polyphosphazene/poly(alpha-hydroxyester) blend whose degradation products are less acidic than those of the poly(alpha-hydroxyester) alone. In this study, the degradation characteristics of a blend of poly(lactide-co-glycolide) (50:50 PLAGA) and poly[(50% ethyl glycinato)(50% p-methylphenoxy) phosphazene] (PPHOS-EG50) were qualitatively and quantitatively determined with comparisons made to the parent polymers. Circular matrices (14mm diameter) of the PLAGA, PPHOS-EG50 and PLAGA-PPHOS-EG50 blend were degraded in non-buffered solutions (pH 7.4). The degraded polymers were characterized for percentage mass loss and molecular weight and the degradation medium was characterized for acid released in non-buffered solutions. The amounts of neutralizing base necessary to bring about neutral pH were measured for each polymer or polymer blend during degradation. The poly(phosphazene)/poly(lactide-co-glycolide) blend required significantly less neutralizing base in order to bring about neutral solution pH during the degradation period studied. The results indicated that the blend degraded at a rate intermediate to that of the parent polymers and that the degradation products of the polyphosphazene neutralized the acidic degradation products of PLAGA. Thus, results from these in vitro degradation studies suggest that the PLAGA-PPHOS-EG50 blend may provide a viable improvement to biomaterials based on acid-releasing organic polymers.

"Comfort" as a Critical Success Factor in Blended Learning Courses

Science.gov (United States)

Futch, Linda S.; deNoyelles, Aimee; Thompson, Kelvin; Howard, Wendy

2016-01-01

There are substantial quantitative research and anecdotal reports on blended learning and blended learning courses. However, few research studies focus on what happens at the classroom level. This research study aims to consider the highly contextual environment of effective blended learning courses by identifying the strategies instructors use to…

Student acceptance of blended learning in Nigeria: a case study of ...

African Journals Online (AJOL)

Student acceptance of blended learning in Nigeria: a case study of Landmark University. ... instrument and the acceptance of blended learning was tested using UTAUT model. ... Keywords: Blended learning, UTAUT, technology acceptance ...

Students' experiences of blended learning across a range of postgraduate programmes.

Science.gov (United States)

Smyth, Siobhan; Houghton, Catherine; Cooney, Adeline; Casey, Dympna

2012-05-01

The article describes the students' experiences of taking a blended learning postgraduate programme in a school of nursing and midwifery. The indications to date are that blended learning as a pedagogical tool has the potential to contribute and improve nursing and midwifery practice and enhance student learning. Little is reported about the students' experiences to date. Focus groups were conducted with students in the first year of introducing blended learning. The two main themes that were identified from the data were (1) the benefits of blended learning and (2) the challenges to blended learning. The blended learning experience was received positively by the students. A significant finding that was not reported in previous research was that the online component meant little time away from study for the students suggesting that it was more invasive on their everyday life. It is envisaged that the outcomes of the study will assist educators who are considering delivering programmes through blended learning. It should provide guidance for further developments and improvements in using Virtual Learning Environment (VLE) and blended learning in nurse education. Copyright © 2011 Elsevier Ltd. All rights reserved.

Blended learning experience in teacher education: the trainees´ perspective

Directory of Open Access Journals (Sweden)

Monika Černá

2009-03-01

Full Text Available The article deals with blended learning in the context of pre-graduate English language teacher education. Firstly, the concept of blended learning is defined, then, the attention is focused on the online component of a blend, namely on the issue of interpersonal interaction including the challenges, which learning through online networking poses. Finally, results of a small–scale research are provided to offer insights into teacher trainees´ perspective of the blended learning experience at the University of Pardubice, Czech Republic.

Preparation and Properties of Polyhedral Oligosilsesquioxanes/Polymers Blends

National Research Council Canada - National Science Library

Blanski, Rusty

2000-01-01

... (polycarbonate, SB rubber, etc.) resulting in a clear blend. We also report that aliphatic POSS compounds are also dispersible in high density polyethylene. The synthesis of POSS/polymer blends as well as some physical properties will be discussed.

blend4php: a PHP API for galaxy.

Science.gov (United States)

Wytko, Connor; Soto, Brian; Ficklin, Stephen P

2017-01-01

Galaxy is a popular framework for execution of complex analytical pipelines typically for large data sets, and is a commonly used for (but not limited to) genomic, genetic and related biological analysis. It provides a web front-end and integrates with high performance computing resources. Here we report the development of the blend4php library that wraps Galaxy's RESTful API into a PHP-based library. PHP-based web applications can use blend4php to automate execution, monitoring and management of a remote Galaxy server, including its users, workflows, jobs and more. The blend4php library was specifically developed for the integration of Galaxy with Tripal, the open-source toolkit for the creation of online genomic and genetic web sites. However, it was designed as an independent library for use by any application, and is freely available under version 3 of the GNU Lesser General Public License (LPGL v3.0) at https://github.com/galaxyproject/blend4phpDatabase URL: https://github.com/galaxyproject/blend4php. © The Author(s) 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Evaluation of intestinal phosphate binding to improve the safety profile of oral sodium phosphate bowel cleansing.

Directory of Open Access Journals (Sweden)

Stef Robijn

Full Text Available Prior to colonoscopy, bowel cleansing is performed for which frequently oral sodium phosphate (OSP is used. OSP results in significant hyperphosphatemia and cases of acute kidney injury (AKI referred to as acute phosphate nephropathy (APN; characterized by nephrocalcinosis are reported after OSP use, which led to a US-FDA warning. To improve the safety profile of OSP, it was evaluated whether the side-effects of OSP could be prevented with intestinal phosphate binders. Hereto a Wistar rat model of APN was developed. OSP administration (2 times 1.2 g phosphate by gavage with a 12h time interval induced bowel cleansing (severe diarrhea and significant hyperphosphatemia (21.79 ± 5.07 mg/dl 6h after the second OSP dose versus 8.44 ± 0.97 mg/dl at baseline. Concomitantly, serum PTH levels increased fivefold and FGF-23 levels showed a threefold increase, while serum calcium levels significantly decreased from 11.29 ± 0.53 mg/dl at baseline to 8.68 ± 0.79 mg/dl after OSP. OSP administration induced weaker NaPi-2a staining along the apical proximal tubular membrane. APN was induced: serum creatinine increased (1.5 times baseline and nephrocalcinosis developed (increased renal calcium and phosphate content and calcium phosphate deposits on Von Kossa stained kidney sections. Intestinal phosphate binding (lanthanum carbonate or aluminum hydroxide was not able to attenuate the OSP induced side-effects. In conclusion, a clinically relevant rat model of APN was developed. Animals showed increased serum phosphate levels similar to those reported in humans and developed APN. No evidence was found for an improved safety profile of OSP by using intestinal phosphate binders.

Evaluation of the compatibility induced by ionizing radiation on polymeric blends

International Nuclear Information System (INIS)

Pino, Eddy S.; Machado, Luci D.B.; Feitosa, Marcos A.F.; Giovedi, Claudia

2011-01-01

To produce new polymers is a costly and time consuming task. Therefore, the utilization of existing polymers in form of blends enables to obtain new polymeric materials at a competitive cost. In this sense, polymer blending has become a growing scientific and commercial development activity. In most of the cases, polymeric blends have immiscible components and this represents an unbecoming situation on blend design. For such immiscible blends, it is required the use of compatibilizers to gain properties advantage. Compatibilization process can be achieved by chemical handling using additives and heat. On the other hand, ionizing radiation induces compatibilization by free radicals, which improve the dispersion and adhesion of the blend phases, without use of chemical additives and at room temperature. In this work, a polyamide 6.6/low-density polyethylene 75/25% wt/wt composition blend was electron beam irradiated up to 250 kGy, and thereafter mechanical tests were carried out. Tensile measurements have shown that the strength at break increases, the elongation at break decreases, the resistance to impact decreases and hardness increases when the radiation dose increases. Since this mechanical behavior is due to cross-linking and to the radiation induced blend compatibilization, this compatibility was evaluated by the approach of the glass transition temperatures for both components using DMA measurements. The results have shown that the glass transition temperatures of the blend components got closer in 8 deg C in the irradiated sample, when compared to the glass transition temperature values obtained for non-irradiated blend. (author)

Evaluation of the compatibility induced by ionizing radiation on polymeric blends

Energy Technology Data Exchange (ETDEWEB)

Pino, Eddy S.; Machado, Luci D.B., E-mail: lmachado@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Feitosa, Marcos A.F. [Centro Paula Souza, Faculdade de Tecnologia da Zona Leste, Sao Paulo, SP (Brazil); Giovedi, Claudia, E-mail: claudia.giovedi@ctmsp.mar.mil.b [Centro Tecnologico da Marinha em Sao Paulo (CTMSP), Sao Paulo, SP (Brazil). Dept. de Tecnologia de Reatores Nucleares

2011-07-01

To produce new polymers is a costly and time consuming task. Therefore, the utilization of existing polymers in form of blends enables to obtain new polymeric materials at a competitive cost. In this sense, polymer blending has become a growing scientific and commercial development activity. In most of the cases, polymeric blends have immiscible components and this represents an unbecoming situation on blend design. For such immiscible blends, it is required the use of compatibilizers to gain properties advantage. Compatibilization process can be achieved by chemical handling using additives and heat. On the other hand, ionizing radiation induces compatibilization by free radicals, which improve the dispersion and adhesion of the blend phases, without use of chemical additives and at room temperature. In this work, a polyamide 6.6/low-density polyethylene 75/25% wt/wt composition blend was electron beam irradiated up to 250 kGy, and thereafter mechanical tests were carried out. Tensile measurements have shown that the strength at break increases, the elongation at break decreases, the resistance to impact decreases and hardness increases when the radiation dose increases. Since this mechanical behavior is due to cross-linking and to the radiation induced blend compatibilization, this compatibility was evaluated by the approach of the glass transition temperatures for both components using DMA measurements. The results have shown that the glass transition temperatures of the blend components got closer in 8 deg C in the irradiated sample, when compared to the glass transition temperature values obtained for non-irradiated blend. (author)