WorldWideScience

Sample records for alternative starting materials

  1. Alternate shield material feasibility

    Energy Technology Data Exchange (ETDEWEB)

    Specht, E.R.; Levitt, L.B.

    1984-04-01

    The feasibility and cost/benefit of using materials other than stainless steel for in-vessel neutron shielding in large LMFBRs were investigated. Canned vibratorally compacted B/sub 4/C powder shields were found to be much more economical than stainless steel (a savings of $1.1M in loop plant designs and $9.4M in pool plant designs). The helium gas pressure buildup in B/sub 4/C shields placed around LMFBR in-vessel components (direct reactor heat exchangers in a loop reactor and intermediate heat exchangers in a pool reactor) would only be 0.04 atm after 40 y of reactor operation (with 80% dense powder). The irradiation-induced swelling of the B/sub 4/C would only be 0.002%. No adverse reactor impact would occur if the B/sub 4/C escaped from the B/sub 4/C shields.

  2. Alternate shield material feasibility

    International Nuclear Information System (INIS)

    The feasibility and cost/benefit of using materials other than stainless steel for in-vessel neutron shielding in large LMFBRs were investigated. Canned vibratorally compacted B4C powder shields were found to be much more economical than stainless steel (a savings of $1.1M in loop plant designs and $9.4M in pool plant designs). The helium gas pressure buildup in B4C shields placed around LMFBR in-vessel components (direct reactor heat exchangers in a loop reactor and intermediate heat exchangers in a pool reactor) would only be 0.04 atm after 40 y of reactor operation (with 80% dense powder). The irradiation-induced swelling of the B4C would only be 0.002%. No adverse reactor impact would occur if the B4C escaped from the B4C shields

  3. 20 CFR 404.242 - Use of old-start primary insurance amount as guaranteed alternative.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Use of old-start primary insurance amount as guaranteed alternative. 404.242 Section 404.242 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL OLD-AGE, SURVIVORS AND DISABILITY INSURANCE (1950- ) Computing Primary Insurance Amounts...

  4. Parameters matching requirements for diesel free piston linear alternator start-up

    Directory of Open Access Journals (Sweden)

    Yan-xiao Li

    2015-03-01

    Full Text Available It is important to identify the relationship between the starting requirements and the structure parameters of the diesel free piston linear alternator on the structural design stage. In this article, the forces applied on the moving part during the starting process are analyzed, and an oscillation model is established. The numerical simulation results of the oscillation model are presented, and the energy-transfer mechanism is analyzed. Then, the oscillation model is simplified by utilizing the energy balance theory. Expressions of the achieved starting frequency and required starting force are derived and the effects of different design variables on them are investigated. The results show that the achieved compression ratio is determined by the energy balance between the friction consumption and the energy supplied by the starting force. The starting frequency achieved and starting force required are associated with the cylinder bore, the moving mass, and effective stroke of the engine, which can be applied to the matching design and optimization of the prototype.

  5. NICKEL AS AN ALTERNATIVE AUTOMOTIVE BODY MATERIAL

    Directory of Open Access Journals (Sweden)

    T. Joseph Sahaya Anand

    2012-06-01

    Full Text Available The study of the thermal, chemical and mechanical properties of pure nickel as an alternative automotive body material is presented in this paper. Current automotive components mainly use steel as the body material. Due to the increasing demand for high performance and related issues, interest is moving towards alternative materials to steel. The hardness values of both heat-treated and non-heat treated pure nickel do not change after annealing; the hardness values are in the range of 118 to 123 HV. As the annealing temperature increases, the ultimate tensile strength, yield strength and Young’s modulus decrease, which indicates that the ductility increases. The highest ultimate tensile strength of pure nickel at 300 °C annealed temperature is 758.78 MPa. X-ray diffraction (XRD studies confirmed pure nickel as a face centred cubic (FCC structure with a lattice constant measured as 0.3492 nm for the unannealed sample, which increases to 0.3512 nm for the annealed samples. The corrosion rate of both annealed and non-heat treated pure nickel is in the range of 0.0266 to 0.048 mm/year.

  6. Reactor physics assessment of alternate cladding materials

    International Nuclear Information System (INIS)

    A preliminary reactor physics assessment has been performed for candidate alternate cladding materials to replace zirconium alloys in enhanced accident tolerant fuel (ATF) concepts for light water reactors. Proposed ATF concepts seek to reduce severe accident risks by increasing the coping time available to operators for accident response and reducing the extent and rate of heat and hydrogen production from steam oxidation. Candidate materials in this neutronics-focused study included austenitic stainless steel 310SS, alumina-forming ferritic alloys (FeCrAl), and silicon carbide (SiC). Historic 304SS cladding and Zircaloy were considered as reference points. Initial results indicate that the metallic options require increased uranium enrichments and/or decreased cladding thicknesses to match the operating cycle lengths achieved with Zircaloy; FeCrAl offered the smallest reactivity penalty, whereas 310SS showed large negative impacts. Ceramic SiC cladding performed well if cladding thicknesses remained similar to those for Zircaloy, but large clad thickness increases led to negative impacts. Fuel pellet relative radial power distributions were similar for all clad materials analyzed. Finally, an economic assessment found that 310SS or FeCrAl could increase fuel pellet costs by 15–36%, while SiC fuel pellet costs were very similar to Zircaloy. (author)

  7. Metal alkoxides as starting materials for hydrolysis processes

    International Nuclear Information System (INIS)

    In this thesis the preparation of some metal alkoxides and their hydrolysis products were studied. The characteristic of each prepared alkoxides and their hydrolyzates were determined. Tetra ethoxysilane was prepared by the elemental route (the reaction of silicon powder with liquid ethanol) in the presence of tin ethoxide as a catalyst. The use of tin alkoxide is considered one of the most developed ways used recently in chemistry, compared to the usage of acids and bases as catalyst previously. It had been confirmed by the usage of (infrared) IR spectroscopy, the structure of the prepared material. Also tin isopropoxide had been prepared and hydrolyzed. Ethoxides of aluminium, magnesium and tin had been prepared by the elemental route. The gelation product had been analyzed. tetraethoxysilane had been also prepared by the halosilane route. Isopropoxide of each aluminium, magnesium and tin had been synthesized, hydrolyzed, allowed to gel and analyzed by IR (infrared) spectroscopy and gas-liquid chromatography. However, results obtained indicated that tin ethoxide is an effective catalyst in the direct synthesis of tetraethoxysilane from silicon powder and liquid ethanol. Gas-liquid chromatography, infra-red (IR) analysis showed that the final reaction product was tetraethoxysilane. (Author)

  8. Alternative Approaches to Group IV Thermoelectric Materials

    Science.gov (United States)

    Snedaker, Matthew Loren

    In the pursuit of energy efficiency, there is a demand for systems capable of recovering waste heat. A temperature gradient across a thermoelectric material results in the thermal diffusion of charge carriers from the hot side to the cold side, giving rise to a voltage that can be used to convert waste heat to electricity. Silicon germanium (SiGe) alloys are the standard materials used for thermoelectric generators at high temperatures. We report an alternative method for preparing p-type Si1- xGex alloys from a boron-doped silica-germania nanocomposite. This is the first demonstration of the thermoelectric properties of SiGe-based thermoelectrics prepared at temperatures below the alloy's melting point through a magnesiothermic reduction of the (SiO 2)1-x(GeO2) x. We observe a thermoelectric power factor that is competitive with the literature record for the conventionally prepared SiGe. The large grain size in our hot pressed SiGe limits the thermoelectric figure of merit to 0.5 at 800°C for an optimally doped p-type Si80Ge 20 alloy. A phosphorus-doped oxide can yield n-type Si1- xGex; however, the current processing method introduces a background boron content that compensates ~10% of the donor impurities and limits the thermoelectric power factor. Spark plasma sintering of the nano-Si1-xGe x yields a heterogeneous alloy with thermal conductivity lower than that of the hot pressed homogeneous alloy due to a reduction in the average crystallite size. Magnesiothermic reduction in the presence of molten salts allows some control over crystallite growth and the extent of Si-Ge alloying.

  9. High belite cement from alternative raw materials

    Directory of Open Access Journals (Sweden)

    Ghorab, H. Y.

    2014-05-01

    Full Text Available Three high belite laboratory clinkers were prepared from traditional and alternative raw materials. Reference clinker was obtained from 77% limestone, 11% sandy clays, 11% fatty clays and 1% iron scales. The fatty clays were replaced by red brick powder in the raw meal of the second clinker and were lowered to 2% with the replacement of 10% of the limestone by egg shells in the third clinker. The SEM examination revealed clear presence of crossed striae and twinning in the rounded belite grains of the reference clinker caused by the transformation of the α´-belite to the β polymorph. Striae were weaker in the second and third clinkers indicating a probable stabilization of the α ‘-belite polymorph. Compressive strength of the respective cements were attained first after 28 days and the early strength did not improve with increasing fineness. Higher compressive strength values were found for the cement prepared from second clinker.Se han preparado tres clinkeres de laboratorio con altos contenidos en belita a partir de materias primas tradicionales y alternativas. El clinker de referencia se obtuvo a partir de una mezcla de caliza, arcillas arenosas y grasas y limaduras de hierro. Las arcillas grasas fueron sustituidas por polvo de ladrillo rojo en la preparación del segundo clinker, y en el tercero el contenido de arcilla grasa fue de solo un 2% y parte de la caliza fue sustituida por cascara de huevo. El estudio realizado por SEM muestra superficies estriadas alrededor de los granos de belita que indican una transformación del polimorfo α´ a la forma β-C₂S, durante el enfriamiento. Esas estrías son menos marcadas en el segundo y tercer clinker, indicando, una estabilización del polimorfo α´-C₂S. Los valores de resistencias a compresión de los correspondientes cementos, a 28 días de curado, no se ven incrementados por la finura de dichos cementos. Las mayores resistencias se obtuvieron en el cemento preparado a partir del cl

  10. A concise synthesis of (+)-batzelladine B from simple pyrrole-based starting materials

    Science.gov (United States)

    Parr, Brendan T.; Economou, Christos; Herzon, Seth B.

    2015-09-01

    Alkaloids, secondary metabolites that contain basic nitrogen atoms, are some of the most well-known biologically active natural products in chemistry and medicine. Although efficient laboratory synthesis of alkaloids would enable the study and optimization of their biological properties, their preparation is often complicated by the basicity and nucleophilicity of nitrogen, its susceptibility to oxidation, and its ability to alter reaction outcomes in unexpected ways--for example, through stereochemical instability and neighbouring group participation. Efforts to address these issues have led to the invention of a large number of protecting groups that temper the reactivity of nitrogen; however, the use of protecting groups typically introduces additional steps and obstacles into the synthetic route. Alternatively, the use of aromatic nitrogen heterocycles as synthetic precursors can attenuate the reactivity of nitrogen and streamline synthetic strategies. Here we use such an approach to achieve a synthesis of the complex anti-HIV alkaloid (+)-batzelladine B in nine steps (longest linear sequence) from simple pyrrole-based starting materials. The route uses several key transformations that would be challenging or impossible to implement using saturated nitrogen heterocycles and highlights some of the advantages of beginning with aromatic reagents.

  11. Alternative Plasmonic Materials: Beyond Gold and Silver

    DEFF Research Database (Denmark)

    Naik, Gururaj V.; Shalaev, Vladimir M.; Boltasseva, Alexandra

    2013-01-01

    in plasmonics and metamaterials lacks good material building blocks in order to realize useful devices. Such devices suffer from many drawbacks arising from the undesirable properties of their material building blocks, especially metals. There are many materials, other than conventional metallic components...... such as gold and silver, that exhibit metallic properties and provide advantages in device performance, design flexibility, fabrication, integration, and tunability. This review explores different material classes for plasmonic and metamaterial applications, such as conventional semiconductors, transparent...

  12. Alternative Raw Materials for Animal Feed

    Directory of Open Access Journals (Sweden)

    A R Alimon

    2009-06-01

    Full Text Available The increase in world fuel prices in the last few years has charged the global animal feedstuffs. In Malaysia, the feed industry is dependent on the importation of corn and soybean meal as the poultry and swine industries are almost totally based on corn soya bean meal diets. However, there are many byproducts and coproducts available in Malaysia as alternatives to corn or soy bean. Since Malaysia has more than 4 million hectares of oil palm plantation and after processing for the oil, large quantities of several byproducts are produced. This paper describes several available byproducts and co products in Malaysia, their nutritive value and their problems.

  13. ALTERNATE MATERIALS IN DESIGN OF RADIOACTIVE MATERIAL PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    Blanton, P.; Eberl, K.

    2010-07-09

    This paper presents a summary of design and testing of material and composites for use in radioactive material packages. These materials provide thermal protection and provide structural integrity and energy absorption to the package during normal and hypothetical accident condition events as required by Title 10 Part 71 of the Code of Federal Regulations. Testing of packages comprising these materials is summarized.

  14. Alternative buffer material. Status of the ongoing laboratory investigation of reference materials and test package 1

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Daniel [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Dueck, Ann; Nilsson, Ulf; Olsson, Siv; Sanden, Torbjoern [Clay Technology AB, Lund (Sweden); Lydmark, Sara; Jaegerwall, Sara; Pedersen, Karsten [Microbial Analytics Sweden AB, Moelnlycke (Sweden); Hansen, Staffan [LTH Lund Univ., Lund (Sweden)

    2011-07-15

    Bentonite clay is part of the Swedish KBS-3 design of final repositories for high level radioactive waste. Wyoming bentonite with the commercial name MX-80 (American Colloid Co) has long been the reference for buffer material in the KBS-3 concept. Extending the knowledge base of alternative buffer materials will make it possible to optimize regarding safety, availability and cost. For this reason the field experiment Alternative Buffer Material (ABM) was started at Aespoe Hard Rock Laboratory during 2006. The experiment includes three medium-scale test packages, each consisting of a central steel tube with heaters, and a buffer of compacted clay. Eleven different clays were chosen for the buffers to examine effects of smectite content, interlayer cations and overall iron content. Also bentonite pellets with and without additional quartz are being tested. The buffer in package 1 had been subjected to wetting by formation water and heating for more than two years (at 130 deg C for {approx} 1 year) when it was retrieved and analyzed. The main purposes of the project were to characterise the clays with respect to hydro-mechanical properties, mineralogy and chemical composition and to identify any differences in behaviour or long term stability. The diversity of clays and the heater of steel also make the experiment suitable for studies of iron-bentonite interactions. This report concerns the work accomplished up to now and is not to be treated as any final report of the project.

  15. (+)-Aromadendrene as chiral starting material for the synthesis of fragrances and pheromones

    NARCIS (Netherlands)

    Lamers, Y.M.A.W.

    2003-01-01

    (+)-Aromadendrene ( 1 ) is a sesquiterpene present in the distillation tail of the oil of Eucalyptus globulus . This distillation tail is commercially available in large quantities at low price and is an interesting starting material for the synthesis of other chiral products. A fai

  16. S-(+)-carvone as starting material in the enantioselective synthesis of natural products.

    NARCIS (Netherlands)

    Verstegen-Haaksma, A.A.

    1994-01-01

    In this thesis the applicability of S-(+)-carvone as chiral starting material in the synthesis of biologically active compounds is examined. S-(+)-carvone is the major compound of caraway essential oil. The essential oil content of caraway seed may vary from 2-7% and it contains about 50-60% of S-(+

  17. Regulating retrotransposon activity through the use of alternative transcription start sites

    DEFF Research Database (Denmark)

    Persson, Jenna; Steglich, Babett; Smialowska, Agata;

    2016-01-01

    a new mechanism of retrotransposon regulation through transcription start site (TSS) selection by altered nucleosome occupancy. We show that Fun30 chromatin remodelers cooperate to maintain a high level of nucleosome occupancy at retrotransposon-flanking long terminal repeat (LTR) elements....... This enforces the use of a downstream TSS and the production of a truncated RNA incapable of reverse transcription and retrotransposition. However, in stressed cells, nucleosome occupancy at LTR elements is reduced, and the TSS shifts to allow for productive transcription. We propose that controlled...

  18. Evolution of sourdough microbiota in spontaneous sourdoughs started with different plant materials.

    Science.gov (United States)

    Ripari, Valery; Gänzle, Michael G; Berardi, Enrico

    2016-09-01

    The preparation of sourdough in bakeries may include the use of inocula, e.g. fruits, flowers or rumen cuts to accelerate the process of selection of suitable microorganisms. The aim of this work was to investigate the effect of these inocula on the microbial evolution in sourdoughs. First, the microbiota of nineteen traditional sourdoughs that were initially started with diverse inocula was identified. Second, de novo sourdoughs were started with plant materials and the evolution of sourdough microbiota was investigated by culture, and by high-resolution melting curve quantitative PCR (HRM-qPCR). This study developed a new protocol for HRM-qPCR analysis of yeast microbiota in sourdough, and indicates this independent culture method suitable for characterization of yeasts. Microbiota of traditional sourdoughs were largely independent from the use of inoculum, however, Acetobacter spp. were identified only in sourdoughs started with apple flowers or apple pulp. In de novo sourdoughs started with plant materials, microbiota rapidly stabilized, and were characterized by Lactobacillus sanfranciscensis, Lactobacillus plantarum, Lactobacillus graminis, or Lactobacillus rossiae, and Saccharomyces cerevisiae as dominant species. Competition experiments revealed that the ecological fitness of L. plantarum, L. graminis, and L. rossiae in wheat or rye malt sourdoughs was lower when compared to L. sanfranciscensis, demonstrating that their presence in de novo sourdoughs reflects dispersal limitation. In conclusion, establishment of microbiota in de novo sourdoughs is dispersal limited. This study provides scientific support for the artisanal practice to inoculate de novo sourdoughs with flowers, berries, or related plant material. PMID:27240218

  19. Engine Materials Compatibility with Alternate Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Thomson, Jeffery K [ORNL; Pawel, Steven J [ORNL; Wilson, Dane F [ORNL

    2013-05-01

    The compatibility of aluminum and aluminum alloys with synthetic fuel blends comprised of ethanol and reference fuel C (a 50/50 mix of toluene and iso-octane) was examined as a function of water content and temperature. Commercially pure wrought aluminum and several cast aluminum alloys were observed to be similarly susceptible to substantial corrosion in dry (< 50 ppm water) ethanol. Corrosion rates of all the aluminum materials examined were accelerated by increased temperature and ethanol content in the fuel mixture, but inhibited by increased water content. Pretreatments designed to stabilize passive films on aluminum increased the incubation time for onset of corrosion, suggesting film stability is a significant factor in the mechanism of corrosion.

  20. Engine Materials Compatability with Alternative Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Pawel, Steve [Oak Ridge National Laboratory; Moore, D. [USCAR

    2013-04-05

    The compatibility of aluminum and aluminum alloys with synthetic fuel blends comprised of ethanol and reference fuel C (a 50/50 mix of toluene and iso-octane) was examined as a function of water content and temperature. Commercially pure wrought aluminum and several cast aluminum alloys were observed to be similarly susceptible to substantial corrosion in dry (< 50 ppm water) ethanol. Corrosion rates of all the aluminum materials examined were accelerated by increased temperature and ethanol content in the fuel mixture, but inhibited by increased water content. Pretreatments designed to stabilize passive films on aluminum increased the incubation time for onset of corrosion, suggesting film stability is a significant factor in the mechanism of corrosion.

  1. Alternative Antimicrobial Approach: Nano-Antimicrobial Materials

    Directory of Open Access Journals (Sweden)

    Nurit Beyth

    2015-01-01

    Full Text Available Despite numerous existing potent antibiotics and other antimicrobial means, bacterial infections are still a major cause of morbidity and mortality. Moreover, the need to develop additional bactericidal means has significantly increased due to the growing concern regarding multidrug-resistant bacterial strains and biofilm associated infections. Consequently, attention has been especially devoted to new and emerging nanoparticle-based materials in the field of antimicrobial chemotherapy. The present review discusses the activities of nanoparticles as an antimicrobial means, their mode of action, nanoparticle effect on drug-resistant bacteria, and the risks attendant on their use as antibacterial agents. Factors contributing to nanoparticle performance in the clinical setting, their unique properties, and mechanism of action as antibacterial agents are discussed in detail.

  2. Alternative materials for crystalline silicon solar cells - Risks and implications

    OpenAIRE

    Kwapil, Wolfram

    2010-01-01

    This thesis considers the use of alternative silicon materials for photovoltaics – often termed “upgraded metallurgical grade” silicon – from different angles and evaluates the risks and implications for the wafer and solar cell properties at selected steps along the entire process chain.The properties of the alternative, upgraded metallurgical grade silicon materials analyzed in the course of this thesis were governed by the simultaneous presence of boron and phosphorus in high concentration...

  3. Quantum Interactive Dualism: An Alternative to Materialism

    Energy Technology Data Exchange (ETDEWEB)

    Stapp, Henry P

    2005-06-01

    Materialism rest implicitly upon the general conception of nature promoted by Galileo and Newton during the seventeenth century. It features the causal closure of the physical: The course of physically described events for all time is fixed by laws that refer exclusively to the physically describeable features of nature, and initial conditions on these feature. No reference to subjective thoughts or feeling of human beings enter. That simple conception of nature was found during the first quarter of the twentieth century to be apparently incompatible with the empirical facts. The founders of quantum theory created a new fundamental physical theory, quantum theory, which introduced crucially into the causal structure certain conscious choices made by human agents about how they will act. These conscious human choices are ''free'' in the sense that they are not fixed by the known laws. But they can influence the course of physically described events. Thus the principle of the causal closure of the physical fails. Applications in psycho-neuro-dynamics are described.

  4. Alternative Start Codon Connects eIF5A to Mitochondria.

    Science.gov (United States)

    Pereira, Karina Danielle; Tamborlin, Letícia; Meneguello, Letícia; de Proença, André Ricardo Gomes; Almeida, Isadora Cristina de Paula Andrade; Lourenço, Rogério Ferreira; Luchessi, Augusto Ducati

    2016-12-01

    Eukaryotic translation initiation factor 5A (eIF5A), a protein containing the amino acid residue hypusine required for its activity, is involved in a number of physiological and pathological cellular processes. In humans, several EIF5A1 transcript variants encode the canonical eIF5A1 isoform B, whereas the hitherto uncharacterized variant A is expected to code for a hypothetical eIF5A1 isoform, referred to as isoform A, which has an additional N-terminal extension. Herein, we validate the existence of eIF5A1 isoform A and its production from transcript variant A. In fact, variant A was shown to encode both eIF5A1 isoforms A and B. Mutagenic assays revealed different efficiencies in the start codons present in variant A, contributing to the production of isoform B at higher levels than isoform A. Immunoblotting and mass spectrometric analyses showed that isoform A can undergo hypusination and acetylation at specific lysine residues, as observed for isoform B. Examination of the N-terminal extension suggested that it might confer mitochondrial targeting. Correspondingly, we found that isoform A, but not isoform B, co-purified with mitochondria when the proteins were overproduced. These findings suggest that eIF5A1 isoform A has a role in mitochondrial function. J. Cell. Physiol. 231: 2682-2689, 2016. © 2016 Wiley Periodicals, Inc. PMID:27414022

  5. Influence of Phase Transition of Starting Materials on Growth of GaN Nanomaterials by CVD

    Institute of Scientific and Technical Information of China (English)

    ZHAO Mei; CHEN Xiao-Long; WANG Wen-Jun; ZHANG Zhi-Hua; XU Yan-Ping

    2007-01-01

    @@ Ground by mechanical ball milling under certain conditions,β-Ga2O3 powders can transit to ε-Ga2O3 ones. As starting materials, Ga2O3 powders treated by different methods are used to prepare GaN nanomaterials. It is found that the morphologies of GaN nanomaterials are quite different due to the phase transition of Ga2O3 from β-Ga2O3 to ε-Ga2O3.

  6. Fine defective structure of silicon carbide powders obtained from different starting materials

    Directory of Open Access Journals (Sweden)

    Tomila T.V.

    2006-01-01

    Full Text Available The fine defective structure of silicon carbide powders obtained from silicic acid-saccharose, aerosil-saccharose, aerosil-carbon black, and hydrated cellulose-silicic acid gel systems was investigated. The relation between IR absorption characteristics and the microstructure of SiC particles obtained from different starting materials was established. The numerical relationship between the lattice parameter a and the frequency νTO is presented.

  7. Fine defective structure of silicon carbide powders obtained from different starting materials

    OpenAIRE

    Tomila T.V.; Vlasova M.V.; Kakazey M.G.; Vyshnyakova K.L.; Ragulya A.V.; Pereselentseva L.N.

    2006-01-01

    The fine defective structure of silicon carbide powders obtained from silicic acid-saccharose, aerosil-saccharose, aerosil-carbon black, and hydrated cellulose-silicic acid gel systems was investigated. The relation between IR absorption characteristics and the microstructure of SiC particles obtained from different starting materials was established. The numerical relationship between the lattice parameter a and the frequency νTO is presented.

  8. S-(+)-carvone as starting material in the enantioselective synthesis of natural products.

    OpenAIRE

    Verstegen-Haaksma, A.A.

    1994-01-01

    In this thesis the applicability of S-(+)-carvone as chiral starting material in the synthesis of biologically active compounds is examined. S-(+)-carvone is the major compound of caraway essential oil. The essential oil content of caraway seed may vary from 2-7% and it contains about 50-60% of S-(+)-carvoneS-(+)-carvone exhibits a number of interesting biological activities, eg., antifungal, insecticidal and plant growth regulatory activities. Especially the inhibiting effect of S-(+)-carvon...

  9. Investigation of the Hygrothermal Performance of Alternative Insulation Materials

    DEFF Research Database (Denmark)

    Rode, Carsten; Kristiansen, Finn Harken; Rasmussen, Niels T.

    1999-01-01

    . The materials investigated are: cellulose insulation, sheep's wool, flax, and perlite. These materials, except for the last one, are very hygroscopic. The following two separate investigations are described.1. Investigation of the thermal conductivity at different humidity conditions.The thermal conductivity......The paper gives an account of hygrothermal investigations carried out on some insulation products which are "alternative" to the ones that are traditionally used in Danish constructions. The alternative products are claimed to be friendly both to the environment and to the labour force...... is determined for the different materials with a guarded hot plate apparatus in which different vapour pressure conditions can be maintained over the specimens. The apparatus and some results are presented.2. Computational analysis of the hygrothermal performance of constructions with alternative insulation...

  10. Selection of alternative material for common rail direct injection system

    Directory of Open Access Journals (Sweden)

    N. Senguttuvan

    2014-03-01

    Full Text Available Common rail direct fuel injection is a modern variant of direct fuel injection system for petrol and diesel engines. The common rail system prototype was developed in the late 1960s by Robert Huber of Switzerland and the technology further developed by Dr. Marco. In petrol engine MPFI technology was developed and implemented in earlier days. Basically common rail tube was fabricated by steel for petrol engines. In the current study Steel, Brass, Aluminum alloy a356 and ABS materials were analyzed separately and aluminum is found the best material among the steel, brass and ABS material for common rail injection tube. Keywords: Common Rail Injection System, Alternate Material.

  11. DEMONSTRATION OF PACKAGING MATERIALS ALTERNATIVES TO EXPANDED POLYSTYRENE

    Science.gov (United States)

    This report represents the second demonstration of cleaner technologies to support the goals of the 33/50 Program under the EPA Cooperative Agreement No. CR-821848. The report presents assessment results of alternative packaging materials which could potentially replace expanded...

  12. Tumor-specific usage of alternative transcription start sites in colorectal cancer identified by genome-wide exon array analysis

    Directory of Open Access Journals (Sweden)

    Laurila Kirsti

    2011-10-01

    Full Text Available Abstract Background Approximately half of all human genes use alternative transcription start sites (TSSs to control mRNA levels and broaden the transcriptional output in healthy tissues. Aberrant expression patterns promoting carcinogenesis, however, may arise from alternative promoter usage. Results By profiling 108 colorectal samples using exon arrays, we identified nine genes (TCF12, OSBPL1A, TRAK1, ANK3, CHEK1, UGP2, LMO7, ACSL5, and SCIN showing tumor-specific alternative TSS usage in both adenoma and cancer samples relative to normal mucosa. Analysis of independent exon array data sets corroborated these findings. Additionally, we confirmed the observed patterns for selected mRNAs using quantitative real-time reverse-transcription PCR. Interestingly, for some of the genes, the tumor-specific TSS usage was not restricted to colorectal cancer. A comprehensive survey of the nine genes in lung, bladder, liver, prostate, gastric, and brain cancer revealed significantly altered mRNA isoform ratios for CHEK1, OSBPL1A, and TCF12 in a subset of these cancer types. To identify the mechanism responsible for the shift in alternative TSS usage, we antagonized the Wnt-signaling pathway in DLD1 and Ls174T colorectal cancer cell lines, which remarkably led to a shift in the preferred TSS for both OSBPL1A and TRAK1. This indicated a regulatory role of the Wnt pathway in selecting TSS, possibly also involving TP53 and SOX9, as their transcription binding sites were enriched in the promoters of the tumor preferred isoforms together with their mRNA levels being increased in tumor samples. Finally, to evaluate the prognostic impact of the altered TSS usage, immunohistochemistry was used to show deregulation of the total protein levels of both TCF12 and OSBPL1A, corresponding to the mRNA levels observed. Furthermore, the level of nuclear TCF12 had a significant correlation to progression free survival in a cohort of 248 stage II colorectal cancer samples

  13. Alternative Plasmonic Materials: Alternative Plasmonic Materials: Beyond Gold and Silver (Adv. Mater. 24/2013)

    DEFF Research Database (Denmark)

    Naik, Gururaj V.; Shalaev, Vladimir M.; Boltasseva, Alexandra

    2013-01-01

    and new functionalities with applications in sensing, imaging, data storage, novel light sources, energy conversion, quantum optics and others. The cover image depicts a negatively refracting metamaterial device built from novel materials. Image prepared with the help of Dr. Alexander V. Kildishev....

  14. Advanced materials for alternative fuel capable directly fired heat engines

    Energy Technology Data Exchange (ETDEWEB)

    Fairbanks, J.W.; Stringer, J. (eds.)

    1979-12-01

    The first conference on advanced materials for alternative fuel capable directly fired heat engines was held at the Maine Maritime Academy, Castine, Maine. It was sponsored by the US Department of Energy, (Assistant Secretary for Fossil Energy) and the Electric Power Research Institute, (Division of Fossil Fuel and Advanced Systems). Forty-four papers from the proceedings have been entered into EDB and ERA and one also into EAPA; three had been entered previously from other sources. The papers are concerned with US DOE research programs in this area, coal gasification, coal liquefaction, gas turbines, fluidized-bed combustion and the materials used in these processes or equipments. The materials papers involve alloys, ceramics, coatings, cladding, etc., and the fabrication and materials listing of such materials and studies involving corrosion, erosion, deposition, etc. (LTN)

  15. Effect of the Freshness of Starting Material on the Final Product Quality of Dried Salted Shark

    Directory of Open Access Journals (Sweden)

    Ponnerassery Sukumaran Sudheesh

    2012-04-01

    Full Text Available This study describes the relationship between the freshness of the starting raw material (fish and the final product quality in experimentally dried shark fish. Sharks were stored at room temperature (25ºC for 0, 24 and 48 h and then salted, processed and sun dried at ambient temperatures ranging from 35 to 42ºC. There was marked difference in sensory and microbiological quality of fresh fish stored to different time periods, but, after drying, the quality difference was negligible. The results of this study show that storage of fish up to 48 h under experimental conditions at room temperature does not affect major microbiological quality and proximate composition of the final dried product.

  16. Sweet potato starch residue as starting material to prepare polyacrylonitrile adsorbent via SI-SET-LRP.

    Science.gov (United States)

    Hao, Zhihai; Wang, Dongju; Chen, Hou; Sun, Jinming; Xu, Yuanyuan

    2014-02-26

    Sweet potato starch residue (SPSR) was used as starting material to prepare an eco-friendly adsorbent. SPSR was modified by bromoacetyl bromide to obtain a macroinitiator for surface-initiated single electron transfer-living radical polymerization (SI-SET-LRP) of acrylonitrile (AN) catalyzed by La(0)/hexamethylenetetramine (HMTA) in N,N-dimethylformamide (DMF) in the presence of ascorbic acid (VC). The amidoxime (AO) adsorbent was prepared by the reaction of the graft copolymer bromoactylated sweet potato starch (BSPS)/polyacrylonitrile (BSPS-g-PAN) with hydroxylamine. The maximum adsorption capacity for Hg(II) was 4.03 mmol·g(-1). This simple method provided a novel approach to recycle and reuse agricultural residues for controlling heavy metal pollution. PMID:24512626

  17. Electromagnetic wave propagation in alternating material-metamaterial layered structures

    CERN Document Server

    Carrera-Escobedo, V H

    2016-01-01

    Using the transfer matrix method, we examine the parametric behavior of the transmittance of an electromagnetic plane wave propagating in the lossless regime through a periodic multilayered system as a function of the frequency and angle of incidence of the electromagnetic wave for the case in which the periodic structure comprises alternating material-metamaterial layers. A specific example of high transmittance at any angle of incidence in the visible region of the spectrum is identified

  18. Influence of starting material on the degassing behavior of trachytic and phonolitic melts

    Science.gov (United States)

    Preuss, Oliver; Marxer, Holger; Nowak, Marcus

    2015-04-01

    The dynamic magmatic processes beneath volcanic systems, occurring during magma ascent, cannot be observed directly in nature. Simulation of magma ascent in the lab realized by continuous decompression (CD) of a volatile containing melt is essential to understand these processes that may lead to potentially catastrophic eruptions threatening millions of people in highly populated areas like Naples located between the Campi Flegrei Volcanic Field and the Monte Somma-Vesuvio strato-volcano. In this project, experimental simulations of Campanian Ignimbrite (CI) magma ascent will give insight to the mechanisms of the CI super eruption, thus providing tools for volcanic hazard assessment at the high risk Campanian Volcanic District and other comparable volcanic systems. Additionally, comparable experiments with the same conditions using the 'white pumice' composition of the catastrophic Vesuvius AD 79 (VAD79) eruption, have been conducted. So far, the experiments were performed in an internally heated argon pressure vessel coupled with a high-pressure low-flow metering valve and a piezoelectric nano-positioning system using a starting pressure of 200 MPa, H2O content of about 5 wt% and two different decompression rates (0.024 and 0.17 MPa/s) at a superliquidus temperature of 1050 ° C to ensure a crystal free melt and a homogeneous bubble nucleation. Experiments were conducted with both, glass powder and cylinders, subsequently decompressed to 75 and 100 MPa and rapidly quenched. Beside the results that e.g. decompression rate, volatile content, fluid solubility and target pressure affect the degassing behavior of the melt, the influence of the starting material on the degassing processes is significant. Analyses of BSE- and transmitted light microscopy images revealed a different degassing behavior of glass cylinder experiments compared to powders. Nitrogen has a very low solubility in hydrous silicate melts, supporting our suggestion that preexisting nitrogen rich

  19. Alternative material study for heat assisted magnetic recording transducer application

    Science.gov (United States)

    Xu, B. X.; Cen, Z. H.; Hu, J. F.; Tsai, J. W. H.

    2015-05-01

    In heat assisted magnetic recording (HAMR), optical near field transducer (NFT) is a key component. Au is currently used as NFT material because of its strong surface plasmon effect. Due to the soft property of Au material, reliability of Au NFT becomes a key issue for realizing HAMR production. In this paper, the possibility of alternative materials, including transition metal nitrides (TMNs) and transparent conducting oxides (TCOs) to replace Au is studied. The results show that all of the listed TMN and TCO materials can meet the mechanical requirements at room temperature in terms of hardness and thermal expansion. An optical model, which includes optical waveguide, NFT and FePt media, is used to simulate NFT performances. The results indicate that the resonant wavelengths for NFT with TCO materials are longer than 1500 nm, which is not suitable for HAMR application. TMN materials are suitable for NFT application at wavelength band of around 800 nm. But the NFT efficiency is very low. ZrN is the best material among TMN materials and the efficiency of ZrN NFT is only 13% of the Au NFT's efficiency. Reducing refractive index (n) and increasing extinction coefficient (k) will both lead to efficiency increase. Increasing k contributes more in the efficiency increase, while reducing n has a relatively low NFT absorption. For materials with the same figure of merit, the NFT with larger k material has higher efficiency. Doping materials to increase the material conduction electron density and growing film with larger size grain may be the way to increase k and reduce n.

  20. Valorization of rice straw waste: an alternative ceramic raw material

    Directory of Open Access Journals (Sweden)

    Á. Guzmán A

    2015-03-01

    Full Text Available In the production of rice a large amount of solid residue is produced, for which alternative utilizations are scarce or are not commonly applied in industry. Rice straw (RS is a waste product of rice harvest that is generated in equal or greater quantities than the rice itself. RS is frequently burned in open air, which makes it a significant source of pollution. In the search for possible uses of RS, it should be noted that its ash (RSA is particularly rich in silica, alkaline and alkaline earth metals and may be used as a source of alkalis and silica for the production of triaxial ceramics. The present research work proposes the production of a ceramic raw material from RS for its use in the fabrication of ceramic materials for the construction industry. Based on the chemical and mineralogical composition of RSA created under different thermal conditions, the most suitable RSA for this purpose was that obtained from treating RS at a temperature of 800 ºC for a time of 2 h. The resulting RSA presented high contents of SiO2 (79.62%, alkaline oxides (K2O (10.53% and alkaline earth oxides (CaO (2.80%. It is concluded that RSA is a new alternative ceramic raw material that can be used as a replacement for the fluxing (mainly feldspar and inert (quartz materials that are used in the production of triaxial ceramics.

  1. In-situ high temperature XRD of calcium phosphate biomaterial using DEHPA as the starting material

    International Nuclear Information System (INIS)

    A process to produce calcium phosphate biomaterial was done using an organic based phosphoric acid (DEHPA) as its starting material. The gel obtained from this reaction was used to study calcium phosphate transformation using in-situ XRD with temperature ranges from room temperature to 1300 degree C. The results obtained from this analysis show the following phase transformation: Gel β-Ca2P2O7 β-TCP + HA α-TCP + HA, β-Ca2P2O7 forms at 400 degree C and as we heat the sample at 1000 degree C peaks belonging to β- TCP and HA appears showing the transformation of the β-Ca2P2O7 phase. When the sample is heated up further to 1200 degree C, β-TCP is transform into α-TCP. In the cold in-situ study, XRD analysis was performed on the sample from room temperature to -140 degree C. At room the XRD diffractogram shows the sample as an amorphous material and as the temperature was further lowered sharp peaks begins to form indicating that the material had becomes crystalline. The peaks were identified to be that calcium hydrogen phosphate (Ca(H2PO4)2) and this indicates that there is no hydroxyl group removal during the cooling process. The relative crystallinity values obtained for the different cooling temperatures show a slow exponential increase on the initial cooling of 0 to -100 degree C and at further cooling temperatures resulted fast and linear process. Also unlike the in-situ XRD analysis performs at high temperature no phase transformation occurred at this low temperature. (Author)

  2. Organic Chemical Attribution Signatures for the Sourcing of a Mustard Agent and Its Starting Materials.

    Science.gov (United States)

    Fraga, Carlos G; Bronk, Krys; Dockendorff, Brian P; Heredia-Langner, Alejandro

    2016-05-17

    Chemical attribution signatures (CAS) are being investigated for the sourcing of chemical warfare (CW) agents and their starting materials that may be implicated in chemical attacks or CW proliferation. The work reported here demonstrates for the first time trace impurities from the synthesis of tris(2-chloroethyl)amine (HN3) that point to the reagent and the specific reagent stocks used in the synthesis of this CW agent. Thirty batches of HN3 were synthesized using different combinations of commercial stocks of triethanolamine (TEA), thionyl chloride, chloroform, and acetone. The HN3 batches and reagent stocks were then analyzed for impurities by gas chromatography/mass spectrometry. All the reagent stocks had impurity profiles that differentiated them from one another. This was demonstrated by building classification models with partial least-squares discriminant analysis (PLSDA) and obtaining average stock classification errors of 2.4, 2.8, 2.8, and 11% by cross-validation for chloroform (7 stocks), thionyl chloride (3 stocks), acetone (7 stocks), and TEA (3 stocks), respectively, and 0% for a validation set of chloroform samples. In addition, some reagent impurities indicative of reagent type were found in the HN3 batches that were originally present in the reagent stocks and presumably not altered during synthesis. More intriguing, impurities in HN3 batches that were apparently produced by side reactions of impurities unique to specific TEA and chloroform stocks, and thus indicative of their use, were observed. PMID:27116337

  3. Organic Chemical Attribution Signatures for the Sourcing of a Mustard Agent and Its Starting Materials

    Energy Technology Data Exchange (ETDEWEB)

    Fraga, Carlos G.; Bronk, Krys; Dockendorff, Brian P.; Heredia-Langner, Alejandro

    2016-05-17

    Chemical attribution signatures (CAS) are being investigated for the sourcing of chemical warfare (CW) agents and their starting materials that may be implicated in chemical attacks or CW proliferation. The work reported here demonstrates for the first time trace impurities produced during the synthesis of tris(2-chloroethyl)amine (HN3) that point to specific reagent stocks used in the synthesis of this CW agent. Thirty batches of HN3 were synthesized using different combinations of commercial stocks of triethanolamine (TEA), thionyl chloride, chloroform, and acetone. The HN3 batches and reagent stocks were then analyzed for impurities by gas chromatography/mass spectrometry. Reaction-produced impurities indicative of specific TEA and chloroform stocks were exclusively discovered in HN3 batches made with those reagent stocks. In addition, some reagent impurities were found in the HN3 batches that were presumably not altered during synthesis and believed to be indicative of reagent type regardless of stock. Supervised classification using partial least squares discriminant analysis (PLSDA) on the impurity profiles of chloroform samples from seven stocks resulted in an average classification error by cross-validation of 2.4%. A classification error of zero was obtained using the seven-stock PLSDA model on a validation set of samples from an arbitrarily selected chloroform stock. In a separate analysis, all samples from two of seven chloroform stocks that were purposely not modeled had their samples matched to a chloroform stock rather than assigned a “no class” classification.

  4. Nanocomposite Materials of Alternately Stacked C60 Monolayer and Graphene

    Directory of Open Access Journals (Sweden)

    Makoto Ishikawa

    2010-01-01

    Full Text Available We synthesized the novel nanocomposite consisting alternately of a stacked single graphene sheet and a C60 monolayer by using the graphite intercalation technique in which alkylamine molecules help intercalate large C60 molecules into the graphite. Moreover, it is found that the intercalated C60 molecules can rotate in between single graphene sheets by using C13 NMR measurements. This preparation method provides a general way for intercalating huge fullerene molecules into graphite, which will lead to promising materials with novel mechanical, physical, and electrical properties.

  5. A straightforward and efficient method for the synthesis of diversely substituted {beta}-aminoketones and {gamma}-aminoalcohols from 3-(N,N-dimethylamino)propiophenones as starting materials

    Energy Technology Data Exchange (ETDEWEB)

    Abonia, Rodrigo; Arteaga, Danny; Castillo, Juan; Insuasty, Braulio; Quiroga, Jairo; Ortiz, Alejandro, E-mail: rodrigo.abonia@correounivalle.edu.co [Universidad del Valle, Cali (Colombia). Department of Chemistry. Research Group of Heterocyclic Compounds

    2013-09-15

    Libraries of novel {beta}-aminoketones and {gamma}-aminoalcohols showing a wide structural diversity were easily obtained from a simple approach, using 3-(N,N-dimethylamino)propiophenone derivatives as key starting material. The procedure involved initially an N-alkylation of secondary benzylamines with propiophenone salts yielding the desired {beta}-aminoketones. Chemical or catalytic reduction of their carbonyl groups provided the final {gamma}-aminoalcohols in good yields. This protocol proved to be convenient as an alternative route for the synthesis of the local anesthetic Falicain Registered-Sign and for the topic antifungal drug Naftifine Registered-Sign . (author)

  6. Materials for Alternative Energies: Computational Materials Discovery and Crystal Structure Prediction

    Science.gov (United States)

    Wolverton, Chris

    2013-03-01

    Many of the key technological problems associated with alternative energies may be traced back to the lack of suitable materials. The materials discovery process may be greatly aided by the use of computational methods, particular those atomistic methods based on density functional theory. In this talk, we present an overview of recent work on energy-related materials from density-functional based approaches. We have developed novel computational tools which enable accurate prediction of crystal structures for new materials (using both Monte Carlo and Genetic Algorithm based approaches), materials discovery via high-throughput, data mining techniques, and automated phase diagram calculations. We highlight applications in the area of Li battery materials and hydrogen storage materials.

  7. Mesoporous Carbon-based Materials for Alternative Energy Applications

    Science.gov (United States)

    Cross, Kimberly Michelle

    Increasing concerns for the escalating issues activated by the effect of carbon dioxide emissions on the global climate from extensive use of fossil fuels and the limited amount of fossil resources has led to an in-depth search for alternative energy systems, primarily based on nuclear or renewable energy sources. Recent innovations in the production of more efficient devices for energy harvesting, storage, and conversion are based on the incorporation of nanostructured materials into electrochemical systems. The aforementioned nano-electrochemical energy systems hold particular promise for alternative energy transportation related technologies including fuel cells, hydrogen storage, and electrochemical supercapacitors. In each of these devices, nanostructured materials can be used to increase the surface area where the critical chemical reactions occur within the same volume and mass, thereby increasing the energy density, power density, electrical efficiency, and physical robustness of the system. Durable corrosion resistant carbon support materials for fuel cells have been designed by adding conductive low cost carbon materials with chemically robust ceramic materials. Since a strict control of the pore size is mandatory to optimize properties for improved performance, chemical activation agents have been utilized as porogens to tune surface areas, pore size distributions, and composition of carbon-based mesoporous materials. Through the use of evaporative self-assembly methods, both randomly disordered and surfactant-templated, ordered carbon-silica nanocomposites have been synthesized with controlled surface area, pore volume, and pore size ranging from 50-800 m2/g, 0.025-0.75 cm3/g, and 2-10 nm, respectively. Multi-walled carbon nanotubes (MWNTs) ranging from 0.05-1.0 wt. % were added to the aforementioned carbon-silica nanocomposites, which provided an additional increase in surface area and improved conductivity. Initially, a conductivity value of 0.0667 S

  8. Paddy Straw as an Alternate Bedding Material for Broiler Chicks

    Directory of Open Access Journals (Sweden)

    Navneet K

    2015-08-01

    Full Text Available Burning of agricultural residues especially paddy straw is now recognized as a major source of environmental concern in India. Burning of huge quantities of paddy straw annually leads to emission of obnoxious gases thus causing adverse impacts on, health of human, animal and bird population. This practice can be discouraged through its utilization as an alternate litter material to commonly used paddy husk which is now available at costly prices because of its use in different industries thus raising the cost of broiler production. This was evaluated through the experiment during winter season conducted on broiler chicks. Broiler chicks (n=144 were distributed into three treatment groups, each having 4 replicates of 12 chicks with equal sex and ratio and average group weight, and reared up to 42 days of age under similar conditions of housing and management except the variation in litter material. Paddy husk (PH, unchopped paddy straw (UPS and chopped paddy straw (CPS were used as different litter materials. The growth parameters tested in the experiment were body weight, weight gain, FCR, PER, EER and carcass characteristics (viz. evisceration rate and proportion of cut-up parts. The litter type had no significant effect on body weight, weight gain, FCR, PER and EER among all the treatments. The average body weight at 42 days of age was 1939, 1947 and 1960 g, respectively in PH, CPS, UCPS groups. The bedding type had no significant effect and no influence on the carcass characteristics viz. evisceration rate and proportion of cut-up parts of the carcass, so it was concluded that paddy straw can be used as good bedding material for broiler chicks.

  9. Alternate electrode materials for the SP100 reactor. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Randich, E.

    1992-05-01

    This work was performed in response to a request by the Astro-Space Division of the General Electric Co. to develop alternate electrodes materials for the electrodes of the PD2 modules to be used in the SP100 thermoelectric power conversion system. Initially, the project consisted of four tasks: (1) development of a ZrB{sub 2} (C) CVD coating on SiMo substrates, (2) development of a ZrB{sub 2} (C) CVD coating on SiGe substrates, (3) development of CVI W for porous graphite electrodes, and (4) technology transfer of pertinent developed processes. The project evolved initially into developing only ZrB{sub 2} coatings on SiGe and graphite substrates, and later into developing ZrB{sub 2} coatings only on graphite substrates. Several sizes of graphite and pyrolytic carbon-coated graphite substrates were coated with ZrB{sub 2} during the project. For budgetary reasons, the project was terminated after half the allotted time had passed. Apart from the production of coated specimens for evaluation, the major accomplishment of the project was the development of the CVD processing to produce the desired coatings.

  10. A simple start - A potential use of simplified english materials in the inclusive classroom

    OpenAIRE

    Rix, Jonathan

    2003-01-01

    This paper examines issues surrounding simplified English materials (SEMs) and their usage. It considers their value in light of widespread support for authentic materials, the communicative approach and bilingual support and learning, contrasting this with the call for language simplification for children with Down syndrome. It sets these conflicting messages against a discussion of differentiated materials and current classroom practices. Drawing on these two different strands it suggests t...

  11. Let's start learning radiation. Supplementary material on radiation for secondary school students

    International Nuclear Information System (INIS)

    The Japan Atomic Energy Agency has been organizing training programs for engineers in Asian countries introducing nuclear technology. In 2012, we launched a course ‘Basic Radiation Knowledge for School Education’ as we thought disseminating accurate knowledge on radiation to school students and public would also be important in those countries after Fukushima-Daiichi nuclear power station accident. Ministry of Education, Culture, Sports, Science and Technology - Japan published supplemental learning material on radiation for secondary school students and teachers in Japanese in October 2011. Since the learning material is designed to give a clear explanation of radiation and covers various topics, we thought it would also be beneficial for young students in the world if a learning material in English was available. Therefore, we made a new learning material in English using the topics covered in supplemental learning material on radiation in Japanese as a reference. This learning material has been favourably evaluated by the International Atomic Energy Agency (IAEA) and will be widely used as a practical educational tool in many countries around the world through the IAEA. (author)

  12. Preparation of nanofluids based on solar salt and boehmite nanoparticles: Characterization of starting materials

    Science.gov (United States)

    Muñoz-Sánchez, B.; Nieto-Maestre, J.; Iparraguirre-Torres, I.; Sánchez-García, J. A.; Julia, J. E.; García-Romero, A.

    2016-05-01

    A nanofluid composed of Solar Salt (SS) and boehmite nanoparticles (A) in a concentration of 1% by weight, is proposed as thermal storage medium for Concentrated Solar Power (CSP) plants. A wide characterization of the raw materials has been done, focused on their thermal stability and the nanoparticle primary size and shape among other properties such as its specific heat and crystalline structure. Some features of the final nanofluids have been also investigated: thermal stability, nanoparticle sizes and their distribution and specific heat. The showed results confirm that these materials are thermally stable in the working temperature range both individually and combined. In addition, the synthesis procedure implemented is effective to keep the nanoparticle sizes in the nanometric range (<100 nm). These findings mean the first step to carry on research and characterization of this nanofluid.

  13. Influence of the starting materials on performance of high temperature oxide fuel cells devices

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Emilia Satoshi Miyamaru; Yoshito, Walter Kenji; Ussui, Valter; Lazar, Dolores Ribeiro Ricci; Castanho, Sonia Regina Homem de Mello; Paschoal, Jose Octavio Armani [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: esmiyseo@net.ipen.br

    2004-03-01

    High temperature solid oxide fuel cells (SOFCs) offer an environmentally friendly technology to convert gaseous fuels such as hydrogen, natural gas or gasified coal into electricity at high efficiencies. Besides the efficiency, higher than those obtained from the traditional energy conversion systems, a fuel cell provides many other advantages like reliability, modularity, fuel flexibility and very low levels of N Ox and S Ox emissions. The high operating temperature (950-1000 deg C) used by the current generation of the solid oxide fuel cells imposes severe constraints on materials selection in order to improve the lifetime of the cell. Besides the good electrical, electrochemical, mechanical and thermal properties, the individual cell components must be stable under the fuel cell operating atmospheres. Each material has to perform not only in its own right but also in conjunction with other system components. For this reason, each cell component must fulfill several different criteria. This paper reviews the materials and the methods used to fabricate the different cell components, such as the cathode, the electrolyte, the anode and the interconnect. Some remarkable results, obtained at IPEN (Nuclear Energy Research Institute) in Sao Paulo, have been presented. (author)

  14. Influence of the starting materials on performance of high temperature oxide fuel cells devices

    Directory of Open Access Journals (Sweden)

    Emília Satoshi Miyamaru Seo

    2004-03-01

    Full Text Available High temperature solid oxide fuel cells (SOFCs offer an environmentally friendly technology to convert gaseous fuels such as hydrogen, natural gas or gasified coal into electricity at high efficiencies. Besides the efficiency, higher than those obtained from the traditional energy conversion systems, a fuel cell provides many other advantages like reliability, modularity, fuel flexibility and very low levels of NOx and SOx emissions. The high operating temperature (950-1000 °C used by the current generation of the solid oxide fuel cells imposes severe constraints on materials selection in order to improve the lifetime of the cell. Besides the good electrical, electrochemical, mechanical and thermal properties, the individual cell components must be stable under the fuel cell operating atmospheres. Each material has to perform not only in its own right but also in conjunction with other system components. For this reason, each cell component must fulfill several different criteria. This paper reviews the materials and the methods used to fabricate the different cell components, such as the cathode, the electrolyte, the anode and the interconnect. Some remarkable results, obtained at IPEN (Nuclear Energy Research Institute in São Paulo, have been presented.

  15. TANK FARM INTERIM SURFACE BARRIER MATERIALS AND RUNOFF ALTERNATIVES STUDY

    Energy Technology Data Exchange (ETDEWEB)

    HOLM MJ

    2009-06-25

    This report identifies candidate materials and concepts for interim surface barriers in the single-shell tank farms. An analysis of these materials for application to the TY tank farm is also provided.

  16. Metal contamination analysis of the epitaxial starting material for scientific CCDs

    CERN Document Server

    Krause, N; Hauff, D; Kemmer, J; Stoetter, D; Strüder, L; Weber, J

    2000-01-01

    Traces of unintentionally introduced titanium into a 3 k OMEGA cm float-zone epitaxial silicon at ultra low levels of 10 sup 1 sup 0 cm sup - sup 3 were found to be the origin of charge transfer loss in pn-CCDs. We identified and backtracked the titanium impurity. The full-depletion design of the pn-CCD, a thin entrance window at the back of the CCD and the low oxygen content of the float-zone material allow no common gettering step. Titanium is introduced into the wafer during the epitaxy process. This is independent of the reactor and the producer of the epitaxial silicon and seems to be a common epitaxy-related problem. To identify the impurity, electron emission rates of traps were measured by means of the CCD. The data were compared with emission rates of identical material obtained by standard-DLTS. The data agree well with literature data of the titanium acceptor level and the titanium donor level. An analysis of the capture cross section by means of the CCD gives a high electron capture cross section....

  17. Thermally reversible thermoset materials based on the chemical modification of alternating aliphatic polyketones

    NARCIS (Netherlands)

    Araya Hermosilla, Rodrigo Andrés

    2016-01-01

    This thesis focused on the synthesis and characterization of different kinds of reversible thermosets and thermoset nanocomposite materials by using alternating aliphatic polyketone (PK) as raw material. Fundamental knowledge was generated regarding the molecular design of new polymers via chemical

  18. Non-proliferation, safeguards, and security for the fissile materials disposition program immobilization alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Duggan, R.A.; Jaeger, C.D.; Tolk, K.M. [Sandia National Labs., Albuquerque, NM (United States); Moore, L.R. [Lawrence Livermore National Lab., CA (United States)

    1996-05-01

    The Department of Energy is analyzing long-term storage and disposition alternatives for surplus weapons-usable fissile materials. A number of different disposition alternatives are being considered. These include facilities for storage, conversion and stabilization of fissile materials, immobilization in glass or ceramic material, fabrication of fissile material into mixed oxide (MOX) fuel for reactors, use of reactor based technologies to convert material into spent fuel, and disposal of fissile material using geologic alternatives. This paper will focus on how the objectives of reducing security and proliferation risks are being considered, and the possible facility impacts. Some of the areas discussed in this paper include: (1) domestic and international safeguards requirements, (2) non-proliferation criteria and measures, (3) the threats, and (4) potential proliferation, safeguards, and security issues and impacts on the facilities. Issues applicable to all of the possible disposition alternatives will be discussed in this paper. However, particular attention is given to the plutonium immobilization alternatives.

  19. Dispersion, spatial growth rate, and start current of a Cherenkov free-electron laser with negative-index material

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuanyuan; Wei, Yanyu; Jiang, Xuebing; Tang, Xianfeng; Shi, Xianbao; Gong, Yubin [National Key Laboratory of Science and Technology on Vacuum Electronics, School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu, Sichuan 610054 (China); Li, Dazhi [Institute for Laser Technology, Suita, Osaka 565-0781 (Japan); Takano, Keisuke; Nakajima, Makoto [Institute of Laser Engineering, Osaka University, Suita, Osaka 565-0781 (Japan); Feng, Jinjun [Beijing Vacuum Electronics Research Institute, Beijing 100016 (China); Miyamoto, Shuji [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Ako, Hyogo 678-1205 (Japan)

    2015-08-15

    We present an analysis of a Cherenkov free-electron laser based on a single slab made from negative-index materials. In this system, a flat electron beam with finite thickness travelling close to the surface of the slab interacts with the copropagating electromagnetic surface mode. The dispersion equation for a finitely thick slab is worked out and solved numerically to study the dispersion relation of surface modes supported by negative-index materials, and the calculations are in good agreement with the simulation results from a finite difference time domain code. We find that under suitable conditions there is inherent feedback in such a scheme due to the characteristics of negative-index materials, which means that the system can oscillate without external reflectors when the beam current exceeds a threshold value, i.e., start current. Using the hydrodynamic approach, we setup coupled equations for this system, and solve these equations analytically in the small signal regime to obtain formulas for the spatial growth rate and start current.

  20. Nuclear materials: Alternatives for relocating Rocky Flats Plant's plutonium operations

    International Nuclear Information System (INIS)

    Major operational problems in a plutonium-processing building at the Department of Energy's Rocky Flats Plant near Denver, Colorado, have existed since the building became operational in 1981. High estimated costs have been associated with repairing the building and potential risks have been associated with the plant's proximity to a major metropolitan center. Four alternatives have been identified for relocating plutonium processing that would cost between about $200 million and $600 million. These alternatives would require between 4 and 10 years to implement, including design, construction and/or alterations and startup. This is in comparison to an estimated cost of about $300 million to repair building 371 at the Rocky Flats Plant and an implementation period of 8 years. The alternative that addresses fabrication operations, the major contributor to safety and health risks at Rocky Flats is to relocate all Rocky Flats plutonium operations. This would cost over $4 billion and take as long as 24 years. On a cost basis alone, this alternative does not appear justified

  1. [Comparative analysis of conventional dental floss and alternative materials].

    Science.gov (United States)

    Campos Júnior, A; Passanezi, E; Serizawa, T C; Barros, A S; Navarro, M F; Lopes, E S

    1990-01-01

    The interproximal plaque-removing effect of three different materials (classic dental floss, rafia floss and indian floss) was tested in a group of 80 males (18 years-old). After two weeks all the materials had the same efficacy in removing the bacterial plaque, with significant reduction in interproximal plaque index. According to an opinion inquiry the rafia floss was the most comfortable material to use and has the lowest cost as well. PMID:2135334

  2. Effect of particle size of starting materials on the structure and properties of biogenic hydroxyapatite/glass composites

    Directory of Open Access Journals (Sweden)

    Oleksandr Parkhomey

    2016-03-01

    Full Text Available The work is devoted to investigation of porous glass-ceramic composite materials on the basis of biogenic hydroxyapatite and sodium borosilicate glass prepared from starting powders with different particle sizes (<50 µm and <160 µm. Starting hydroxyapatite/glass weight ratio was 1.0/0.46 and sintering temperature was ∼800 °C. Microstructural characterization of the surface and fracture of the samples revealed a decrease in sizes of grains and pores with decreasing the particle size of the precursor powder. However, porosity of the composites practically did not depend on the particle size and was equal to 32.5–33.0%. The same tendency was observed for the compression strength (66–67 MPa. However, investigation of structural-mechanical properties using an indentation method, where dominant load is applied to the surface layers of sample, showed up the effect of the particle size of the starting powder on the mechanical properties of the composites: the smaller particle size, the higher mechanical properties.

  3. THE USE OF ALTERNATIVE RAW MATERIAL IN STONEWARE GLAZES

    Directory of Open Access Journals (Sweden)

    Münevver ÇAKI

    2012-12-01

    Full Text Available In this study, Kütahya region’s perlite with high alkali oxide content, at the present time not being assessed in the ceramic industry, was used in stoneware glazes replacing albite, orthoclase and ulexite in the starting batches. New glaze recipes were composed by adding perlite to the standard glaze composition consisting of quartz, kaolin, ulexite, albite and orthoclase. The effects of such a compositional modification on the optical parameters and melting properties of the relevant glazes fired at 1160 °C were investigated. The chemical (XRF and mineralogical analysis (XRD of fluxes were also determined.

  4. Plasmonic Materials For Use In Alternative Approaches To DUV Nanolithography

    Science.gov (United States)

    Estroff, Andrew Charles

    Degradation in image contrast becomes a concern at higher numerical apertures (NA) due to mask induced polarization effects. Rigorous coupled-wave analysis (RCWA) was used to simulate the polarization of radiation by the photomask. The results show that higher NA leads to greater polarization effects in all cases. In general, materials with higher refractive indices and lower extinction coefficients tend to pass more of the TM polarization state, whereas materials with lower refractive indices and a relatively wider range of extinction coefficients pass more TE polarized radiation. These properties can provide new design considerations for the development of next generation masking materials. The unique properties of metamaterials, namely their negative refractive index, permittivity, and permeability, have gained much recent attention. Research into these materials has led to the realization of a host of applications that may be useful to enhance optical nanolithography, such as a high pass pupil filter based on an induced transmission filter design, or an optical superlens. A large selection of materials has been examined both experimentally and theoretically through wavelength to verify their support of surface plasmons, or lack thereof, in the DUV spectrum via the attenuated total reflection (ATR) method using the Kretschmann configuration. At DUV wavelengths, materials that were previously useful at mid-UV and longer wavelengths no longer act as metamaterials. Composites bound between metallic aluminum and Al2O3 exhibit metamaterial behavior, as do other materials such as tin and indium. This provides for real opportunities to explore the potential of the use of such materials for image enhancement with easily obtainable materials at desirable lithographic wavelengths. A software program was created to evaluate possible metal-insulator material stack combinations to find materials with a suitable surface plasmon dispersion for the DUV. The resulting materials

  5. Valorization of rice straw waste: an alternative ceramic raw material

    OpenAIRE

    Á. Guzmán A; S. Delvasto A; E. Sánchez V

    2015-01-01

    In the production of rice a large amount of solid residue is produced, for which alternative utilizations are scarce or are not commonly applied in industry. Rice straw (RS) is a waste product of rice harvest that is generated in equal or greater quantities than the rice itself. RS is frequently burned in open air, which makes it a significant source of pollution. In the search for possible uses of RS, it should be noted that its ash (RSA) is particularly rich in silica, alkaline and alkaline...

  6. Starting electronics

    CERN Document Server

    Brindley, Keith

    2005-01-01

    Starting Electronics is unrivalled as a highly practical introduction for hobbyists, students and technicians. Keith Brindley introduces readers to the functions of the main component types, their uses, and the basic principles of building and designing electronic circuits. Breadboard layouts make this very much a ready-to-run book for the experimenter; and the use of multimeter, but not oscilloscopes, puts this practical exploration of electronics within reach of every home enthusiast's pocket. The third edition has kept the simplicity and clarity of the original. New material

  7. Mitigation of ammunition effects by application of alternative packaging materials

    NARCIS (Netherlands)

    Voort, M.M. van der; Hooijmeijer, P.A.; Meuken, B.; Scholtes, J.H.G.; Makkus, J.C.; Klerk, W.P.C. de

    2013-01-01

    A mass detonation of stored ammunition may lead to devastating injury, material damage, and asset loss. Such a scenario can be initiated by an external (fragment or bullet) impact, or the detonation of nearby ammunition articles, leading to sympathetic reaction/detonation. At a military base, sympat

  8. Corrosion evaluation of alternate nuclear steam generator tubing materials

    International Nuclear Information System (INIS)

    Several materials were evaluated for use in nuclear steam generators (NSG). These materials were exposed to corrosive conditions representative of those found in nuclear steam generators. The materials evaluated were gold, titanium, tantalum, niobium, Hastelloy C-276, Hastelloy G. Nickel 200, nickel-base Alloy 625, and heat-tracked nickel-base Alloy 600. The test environments simulated acid pitting attack, caustic stress corrosion cracking and reduced sulfur attack. In the pitting environment, the monolithic materials did well, however Nickel 200, nickel-base Alloy 600 and Hastelloy G3 did poorly. The remaining alloys, nickel-base Alloy 625 and Hastelloy C-276 were relatively unaffected in the pitting environment. Tantalum, titanium, niobium, nickel-base Alloy 625 performed poorly in the environment designed to evaluate resistance to caustic cracking. Nickel-base Alloy 600 (stress-relieved), Hastelloy C-276, Hasteloy G-3 and Nickel 200 compared fair to good in the caustic sodium. The gold was unaffected in the hot caustic solution. In the environment selected to represent a reduced sulfur environment, nickel-base Alloy 625 and Hastelloy C-276 exhibited considerable resistance. The nickel-base Alloy 600 was attacked within a relatively short period of time

  9. Press Start

    Science.gov (United States)

    Harteveld, Casper

    This level sets the stage for the design philosophy called “Triadic Game Design” (TGD). This design philosophy can be summarized with the following sentence: it takes two to tango, but it takes three to design a meaningful game or a game with a purpose. Before the philosophy is further explained, this level will first delve into what is meant by a meaningful game or a game with a purpose. Many terms and definitions have seen the light and in this book I will specifically orient at digital games that aim to have an effect beyond the context of the game itself. Subsequently, a historical overview is given of the usage of games with a serious purpose which starts from the moment we human beings started to walk on our feet till our contemporary society. It turns out that we have been using games for all kinds of non-entertainment purposes for already quite a long time. With this introductory material in the back of our minds, I will explain the concept of TGD by means of a puzzle. After that, the protagonist of this book, the game Levee Patroller, is introduced. Based on the development of this game, the idea of TGD, which stresses to balance three different worlds, the worlds of Reality, Meaning, and Play, came into being. Interested? Then I suggest to quickly “press start!”

  10. Selection of alternative material for common rail direct injection system

    OpenAIRE

    Senguttuvan, N.; Raja, S; R. Sasidharan

    2014-01-01

    Common rail direct fuel injection is a modern variant of direct fuel injection system for petrol and diesel engines. The common rail system prototype was developed in the late 1960s by Robert Huber of Switzerland and the technology further developed by Dr. Marco. In petrol engine MPFI technology was developed and implemented in earlier days. Basically common rail tube was fabricated by steel for petrol engines. In the current study Steel, Brass, Aluminum alloy a356 and ABS materials were anal...

  11. Alternative technology of nanoparticles consolidation in the bulk material

    Directory of Open Access Journals (Sweden)

    VOLKOV Georgiy Michailovich

    2016-02-01

    Full Text Available Theoretical bases and technological principles of single-stages nanoparticles conso-lidation into bulk material were offered. The theory was implemented on the model system of carbon-carbon in the process of high-temperature pyrolysis of hydrocar-bons. The bulk carbon nanomaterial with unique technical properties was produced. That made it possible to create engineering products which technical characteristics are higher than the existing level in the world. The proposed theory can be adapted to other gas-phase, liquid phase and secondary crystallization processes to create bulk nanomaterials of another chemical composition with no less unique properties.

  12. Feasibility of Target Material Recycling as Waste Management Alternative

    International Nuclear Information System (INIS)

    The issue of waste management has been studied simultaneously along with the development of the ARIES heavy-ion-driven inertial fusion energy (IFE) concept. Options for waste management include disposal in repositories, recycling, or clearance from regulatory control, following a reasonable cooling period. This paper concerns the feasibility of recycling the heavy-ion-beam targets, in particular the hohlraum wall materials that include, for example, Au/Gd, Au, W, Pb, Hg, Ta, Pb/Ta/Cs, Hg/W/Cs, Pb/Hf, Hf, solid Kr, and solid Xe. The choice between target material disposal and recycling depends on the amount of waste generated relative to the nuclear island, the strategy to solve the recycling problem, and the impact of the additional cost and complexity of the recycling process on the overall machine. A detailed flow diagram for the elements of the recycling process was developed to analyze two extreme activation cases: (a) one-shot use and then disposal in a repository and (b) recycling continuously during plant life without removal of transmutation products. Metrics for comparing the two scenarios included waste level, dose to recycling equipment, additional cost, and design complexity. Comparing the two approaches indicated a preference for the one-shot scenario as it generates 1 m3/yr of extremely low-level waste (Class A) and offers attractive design and economics features. Recycling reduces the target waste stream by a factor of 10 or more but introduces additional issues. It may produce high-level waste, requires remote handling, adds radioactive storage facilities, and increases the cost and complexity of the plant. The inventory analysis indicated that the heavy-ion-beam (HIB) target materials represent a very small waste stream compared to that of the nuclear island (<1% of the total waste). This means recycling is not a 'must' requirement for IFE-HIB power plants unless the target materials have cost and/or resource problems (e.g., Au and Gd). In this

  13. Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

    Directory of Open Access Journals (Sweden)

    Strigáč Július

    2015-11-01

    Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

  14. Oxides and nitrides as alternative plasmonic materials in the optical range

    DEFF Research Database (Denmark)

    Naik, Gururaj V.; Kim, Jongbum; Boltasseva, Alexandra

    2011-01-01

    As alternatives to conventional metals, new plasmonic materials offer many advantages in the rapidly growing fields of plasmonics and metamaterials. These advantages include low intrinsic loss, semiconductor-based design, compatibility with standard nanofabrication processes, tunability, and others...... of fabrication and characterization of these new materials and discuss their suitability for a number of metamaterial and plasmonic applications....

  15. 9975 SHIPPING PACKAGE PERFORMANCE OF ALTERNATE MATERIALS FOR LONG-TERM STORAGE APPLICATION

    Energy Technology Data Exchange (ETDEWEB)

    Skidmore, E.; Hoffman, E.; Daugherty, W.

    2010-02-24

    The Model 9975 shipping package specifies the materials of construction for its various components. With the loss of availability of material for two components (cane fiberboard overpack and Viton{reg_sign} GLT O-rings), alternate materials of construction were identified and approved for use for transport (softwood fiberboard and Viton{reg_sign} GLT-S O-rings). As these shipping packages are part of a long-term storage configuration at the Savannah River Site, additional testing is in progress to verify satisfactory long-term performance of the alternate materials under storage conditions. The test results to date can be compared to comparable results on the original materials of construction to draw preliminary conclusions on the performance of the replacement materials.

  16. Findings and Recommendations from the NIST Workshop on Alternative Fuels and Materials: Biocorrosion.

    Science.gov (United States)

    Mansfield, Elisabeth; Sowards, Jeffrey W; Crookes-Goodson, Wendy J

    2015-01-01

    In 2013, the Applied Chemicals and Materials Division of the National Institute of Standards and Technology (NIST) hosted a workshop to identify and prioritize research needs in the area of biocorrosion. Materials used to store and distribute alternative fuels have experienced an increase in corrosion due to the unique conditions caused by the presence of microbes and the chemistry of biofuels and biofuel precursors. Participants in this workshop, including experts from the microbiological, fuel, and materials communities, delved into the unique materials and chemical challenges that occur with production, transport, and storage of alternative fuels. Discussions focused on specific problems including: a) the changing composition of "drop-in" fuels and the impact of that composition on materials; b) the influence of microbial populations on corrosion and fuel quality; and c) state-of-the-art measurement technologies for monitoring material degradation and biofilm formation.

  17. Non-proliferation issues for the disposition of fissile materials using reactor alternatives

    International Nuclear Information System (INIS)

    The Department of Energy (DOE) is analyzing long-term storage on options for excess weapons-usable fissile materials. A number of the disposition alternatives are being considered which involve the use of reactors. The various reactor alternatives are all very similar and include front-end processes that could convert plutonium to a usable form for fuel fabrication, a MOX fuel fab facility, reactors to bum the MOX fuel and ultimate disposal of spent fuel in some geologic repository. They include existing, partially completed, advanced or evolutionary light water reactors and Canadian deuterium uranium (CANDU) reactors. In addition to the differences in the type of reactors, other variants on these alternatives are being evaluated to include the location and number of the reactors, the location of the mixed oxide (MOX) fabrication facility, the ownership of the facilities (private or government) and the colocation and/or separation of these facilities. All of these alternatives and their variants must be evaluated with respect to non-proliferation resistance. Both domestic and international safeguards support are being provided to DOE's Fissile Materials Disposition Program (FMDP) and includes such areas as physical protection, nuclear materials accountability and material containment and surveillance. This paper will focus on how the non-proliferation objective of reducing security risks and strengthening arms reduction will be accomplished and what some of the nonproliferation issues are for the reactor alternatives. Proliferation risk has been defined in terms of material form, physical environment, and the level of security and safeguards that is applied to the material. Metrics have been developed for each of these factors. The reactor alternatives will be evaluated with respect to these proliferation risk factors at each of the unit process locations in the alternative

  18. An alternative approach to synthesis of 2--butyl-5-nitrobenzofuran derivative: A key starting material for dronedarone hydrochloride

    Indian Academy of Sciences (India)

    P Raja Gopal; E R R Chandrashekar; M Saravanan; B Vijaya Bhaskar; P Veera Somaiah

    2012-09-01

    A practical synthesis of (2-butyl-5-nitrobenzofuran-3-yl)(4-hydroxyphenyl)methanone, a key intermediate in the preparation of anti arrhythmic drug, is described. The commercially available 4-nitrophenol (3) is converted in five steps to 2-butyl-5-nitrobenzofuran (9) which upon Friedel-Crafts acylation with 4-methoxybenzoyl chloride followed by deprotection of methyl group gives (2).

  19. A life cycle assessment method for alternative material selection strategies in boat structures

    OpenAIRE

    Bardet, Raphaël Régis

    2010-01-01

    In general the use of composites results in shorter production time, lightweight and lower maintenance costs to the marine industry in the leisure, fast and fishing boats sectors. The social and economic benefits of using composite materials have made users complacent about the pollution and the health and safety issues associated with these materials. As the perception of environmental problems changes with time, alternatives with lower emissions allowing for cleaner production and easier di...

  20. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    OpenAIRE

    Sarkar, Dipankar; Pal, Manish; Sarkar, Ashoke K.

    2016-01-01

    There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46...

  1. Sure Start

    Science.gov (United States)

    Moss, Peter

    2004-01-01

    This paper outlines what is involved in Sure Start, one of New Labour's key social policy interventions. It is argued that there are policy continuities with older redemptive policies which focus on young children. It is also argued that Sure Start could provide a bridgehead for a more socially democratic orientation into early childhood policy.

  2. Carbon/graphite composite material study. Appendix C: NASA studies on modification of carbon/graphite fibers and alternative materials

    Science.gov (United States)

    1981-01-01

    The feasibility of modifying resin matrix composites to reduce the potential of electrical shorting from fire released fiber was explored. The effort included modifications to or coatings for graphite fibers, alternative fibers, modifications to matrix materials, and hybrid composites. The objectives included reduction of the conductivity of the graphite fiber, char formation to reduce fiber release, glass formation to prevent fiber release, catalysis to assure fiber consumption in a fire, and replacement of the graphite fibers with nonconductive fibers of similar mechanical potential.

  3. Fissile material disposition program: Screening of alternate immobilization candidates for disposition of surplus fissile materials

    Energy Technology Data Exchange (ETDEWEB)

    Gray, L.W.

    1996-01-08

    With the end of the Cold War, the world faces for the first time the need to dismantle vast numbers of ``excess`` nuclear weapons and dispose of the fissile materials they contain, together with fissile residues in the weapons production complex left over from the production of these weapons. If recently agreed US and Russian reductions are fully implemented, tens of thousands of nuclear weapons, containing a hundred tons or more of plutonium and hundreds of tonnes* of highly enriched uranium (HEU), will no longer be needed worldwide for military purposes. These two materials are the essential ingredients of nuclear weapons, and limits on access to them are the primary technical barrier to prospective proliferants who might desire to acquire a nuclear weapons capability. Theoretically, several kilograms of plutonium, or several times that amount of HEU, is sufficient to make a nuclear explosive device. Therefore, these materials will continue to be a potential threat to humanity for as long as they exist.

  4. Fissile material disposition program: Screening of alternate immobilization candidates for disposition of surplus fissile materials

    International Nuclear Information System (INIS)

    With the end of the Cold War, the world faces for the first time the need to dismantle vast numbers of ''excess'' nuclear weapons and dispose of the fissile materials they contain, together with fissile residues in the weapons production complex left over from the production of these weapons. If recently agreed US and Russian reductions are fully implemented, tens of thousands of nuclear weapons, containing a hundred tons or more of plutonium and hundreds of tonnes* of highly enriched uranium (HEU), will no longer be needed worldwide for military purposes. These two materials are the essential ingredients of nuclear weapons, and limits on access to them are the primary technical barrier to prospective proliferants who might desire to acquire a nuclear weapons capability. Theoretically, several kilograms of plutonium, or several times that amount of HEU, is sufficient to make a nuclear explosive device. Therefore, these materials will continue to be a potential threat to humanity for as long as they exist

  5. The influence of production conditions, starting material and deposition environment on charcoal alteration in a tropical biome.

    Science.gov (United States)

    Ascough, Philippa; Bird, Michael; Meredith, Will; Large, David; Snape, Colin; Manion, Corinne

    2014-05-01

    Natural and anthropogenic burning events are a key link in the global carbon cycle, substantially influencing atmospheric CO2 levels, and consuming c.8700 teragrams yr-1 of dry biomass [1,2,3]. An important result of this process is charcoal, when lignocellulosic structures in biomass (e.g. wood) are converted to aromatic domains with high chemical stability. Charcoal is therefore not readily re-oxidized to CO2, with estimates of 5-7 ky for the half-life of charcoal carbon in soils [3,4]. Charcoal's high carbon content coupled with high environmental resistance has led to the concept of biochar as a valuable means of global carbon sequestration, capable of carbon offsets comparable to annual anthropogenic fuel emissions [5,6,7]. Charcoal is not, however, an environmentally inert substance, and at least some components of charcoal are susceptible to alteration in depositional environments. Despite the importance of charcoal in global carbon cycling, the mechanisms by which charcoal is altered in the environment remain, as yet, poorly understood. This fact limits our ability to properly incorporate both natural environmental charcoal and biochar into global carbon budgets. This study aimed to improve understanding of charcoal alteration in the environment by examining the influence of production conditions, starting material and deposition environment on the physical and chemical characteristics of charcoal at a field site in the Daintree rainforest. These factors have been identified as critical in determining the dynamics of charcoal in depositional environments [8,9] and climatic conditions at the field site (in Tropical Queensland, Australia) are likely to result in extensive alteration of charcoal. Charcoal from wood (Nothofagus spp.), algae (Enteromorpha spp.), and sugarcane (Saccharum spp.) biomass was produced at temperatures over 300-500°C and exposed to conditions of varying pH and vegetation cover. The effect of these variables on charcoal chemistry

  6. Effect of the purity of starting materials on the growth and properties of potassium dihydrogen phosphate single crystals – A comparative study

    Energy Technology Data Exchange (ETDEWEB)

    Rajesh, P., E-mail: rajeshp@ssn.edu.in [Centre for Crystal Growth, SSN College of Engineering, Kalavakkam 603 110 (India); Charoen In, Urit [Department of Physics, Faculty of Science, Mahasarakham University, Mahasarakham 44150 (Thailand); Manyum, Prapun [School of Physics and NANOTEC-SUT Center of Excellence on Advanced Functional Nanomaterials, Suranaree University of Technology, Nakhon Ratchasima, Muang 30000 (Thailand); Ramasamy, P. [Centre for Crystal Growth, SSN College of Engineering, Kalavakkam 603 110 (India)

    2014-11-15

    Highlights: • Bulk size KDP crystal has been grown with higher growth rate. • Systematic study on the effect of starting materials has been done. • Crystalline perfection is maintained in the entire crystal. - Abstract: A systematic study on the effect of purity of starting materials on the growth and properties of potassium dihydrogen phosphate single crystals is crucial for the future study of the material for nonlinear optical applications. Potassium dihydrogen phosphate crystals were grown using high pure (99.999%) and ordinary (99.9%) starting raw materials using slow cooling method in identical conditions. Their optical transparency and crystalline perfection are studied by UV and high resolution X-ray diffraction analyses respectively. The results are checked with the help of etching analyses. The full width at half maximum is 8″ which is close to that expected from the plane wave theory of dynamical X-ray diffraction for an ideally perfect crystal. Results of those studies are correlated with each other. The quantitative results show that the raw material plays an important role in the growth of good quality crystals.

  7. Towards CMOS-compatible nanophotonics: Ultra-compact modulators using alternative plasmonic materials

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Kinsey, Nathaniel; Naik, Gururaj V.;

    2013-01-01

    We propose several planar layouts of ultra-compact plasmonic modulators that utilize alternative plasmonic materials such as transparent conducting oxides and titanium nitride. The modulation is achieved by tuning the carrier concentration in a transparent conducting oxide layer into and out...... at the telecommunication wavelength. Our multilayer structures can be integrated with existing plasmonic and photonic waveguides as well as novel semiconductor-based hybrid photonic/electronic circuits....

  8. Replacing Noble Metals with Alternative Materials in Plasmonics and Metamaterials: how good an idea?

    CERN Document Server

    Khurgin, Jacob B

    2016-01-01

    Noble metals that currently dominate the fields of plasmonics and metamaterials suffer from large ohmic losses. New plasmonic materials, such as doped oxides and nitrides, have smaller material loss, and, using them in place of metals carries promise of reduced-loss plasmonic and metamaterial structures, with sharper resonances and higher field concentration. This promise is put to a rigorous analytical test in this work which reveals that having low material loss is not sufficient to have a reduced modal loss in plasmonic structures. To reduce the modal loss it is absolutely necessary for the plasma frequency to be significantly higher than the operational frequency. Using examples of nanoparticle plasmons and gap plasmons one comes to the conclusion that even in the mid-infrared spectrum metals continue to hold advantage over the alternative media. The new materials may still find application niche where the high absorption loss is beneficial, e.g. in medicine and thermal photovoltaics.

  9. Pineapple leaf fiber as reinforce in composite materials, an alternative for automotive industry

    Energy Technology Data Exchange (ETDEWEB)

    Campos, Rejane Daniela de; Seo, Emilia Satoshi Miyamaru, E-mail: rejanedaniela@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    The composites appear as an extremely favorable alternative for different industries, due to the fact that it combines the best mechanical properties with the best physic-chemical properties of two or more materials. Nowadays, in the evaluation of materials, besides criteria such as economic viability and performance, the environmental criterion was included in this evaluation. Part of the environmental criteria is the use of biodegradable materials and/or recycled materials. In this sense, researches focused on vegetal fibers, as reinforcement in composites are growing considerably and positive results for its performance were achieved. Moreover, the environmental-friendly approach not only is the unique advantage on usage of vegetal fibers, but also it has an economical advantage, because of the low cost and good performance due to low density. The fiber extracted from the pineapple leaf (PALF) is a new alternative for automotive industry as cellulose-based fiber composite. In this sense, the present paper aims to present the characterization of the pineapple leaf fiber for manufacturing the automotive composite materials. Milled pineapple fibers extracted, in two different ways and submitted to mercerisation treatments, were characterized by mechanical and thermal properties; density; morphology; FTIR spectroscopy, EDX and X-ray diffraction. It is important to characterize the fibers, in order to obtain appropriate mechanical properties of composite. (author)

  10. Naturally Abundance Vanillin as Starting Material to Synthesizing 4-(4-Hydroxy-3-methoxyphenyl)-6-methyl-3,4-dihydropyrimidin-2(1H)-one

    OpenAIRE

    Masruri MASRURI; Yuga Adi Pranata

    2015-01-01

    Indonesia is the second biggest producer of natural vanillin. Traditionally it was isolated from the bean of vanilla (Vanilla planifolia Andrews). This paper reports on applying vanillin as starting material for synthesizing a biologically important chemical structure 3,4-dihydropyrimidinone. The reaction was undertaken in one step following multi component reaction (MCR). Products determination was undergone using FTIR and UV-Vis spectrophotometry, and also liquid chromatography-mass spectro...

  11. Sound indoor air quality starts with choice of materials. Better health and higher productivity; Goede binnenluchtkwaliteit begint bij juiste materiaalkeuze. Betere gezondheid, grotere productiviteit

    Energy Technology Data Exchange (ETDEWEB)

    Krieger, J. [DWA Installatie- en Energieadvies, Bodegraven (Netherlands)

    2012-04-15

    Many complaints exist in practice about the indoor air quality. Next to a well-designed and maintained ventilation system, other construction and finishing materials also play a large role in the resulting IAQ (indoor air quality). Good indoor air quality starts with choosing the right materials. [Dutch] In de praktijk blijken er veel klachten over de binnenlucht te bestaan. Naast een goed ontworpen en onderhouden ventilatiesysteem spelen onder andere de bouw- en afwerkingsmaterialen een grote rol in de resulterende IAQ (indoor air quality). Een goede binnenluchtkwaliteit begint dan ook met een juiste materiaalkeuze.

  12. Gas permeability of biochar-amended clay: potential alternative landfill final cover material.

    Science.gov (United States)

    Wong, James Tsz Fung; Chen, Zhongkui; Ng, Charles Wang Wai; Wong, Ming Hung

    2016-04-01

    Compacted biochar-amended clay (BAC) has been proposed as an alternative landfill final cover material in this study. Biochar has long been proposed to promote crop growth, mitigate odor emission, and promote methane oxidation in field soils. However, previous studies showed that soil-gas permeability was increased upon biochar application, which will promote landfill gas emission. The objective of the present study is to investigate the possibility of using compacted BAC as an alternative material in landfill final cover by evaluating its gas permeability. BAC samples were prepared by mixing 425-μm-sieved peanut shell biochar with kaolin clay in different ratios (0, 5, 10, and 15 %, w/w) and compacting at different degrees of compactions (DOC) (80, 85, and 90 %) with an optimum water content of 35 %. The gas permeability of the BACs was measured by flexible wall gas permeameter and the microstructure of the BACs was analyzed by SEM with energy-dispersive x-ray spectroscopy (EDX). The results show that the effects of biochar content on BAC gas permeability is highly dependent on the DOC. At high DOC (90 %), the gas permeability of BAC decreases with increasing biochar content due to the combined effect of the clay aggregation and the inhibition of biochar in the gas flow. However, at low DOC (80 %), biochar incorporation has no effects on gas permeability because it no longer acts as a filling material to the retard gas flow. The results from the present study imply that compacted BAC can be used as an alternative final cover material with decreased gas permeability when compared with clay. PMID:26092359

  13. Efficacy of pine leaves as an alternative bedding material for broiler chicks during summer season

    Directory of Open Access Journals (Sweden)

    Gourav Sharma

    2015-10-01

    Full Text Available Aim: The aim was to assess the efficacy of pine leaves as an alternative bedding material on the performance of broiler chicks. Materials and Methods: The present study was conducted in summer. Total 120, day old Vencobb straight run chicks were procured, and after 5 days of brooding, chicks were randomly distributed into four treatment groups viz. paddy husk (Group I, paddy straw (Group II, pine leaves (Group III, and combination of paddy straw and pine leaves (Group IV, each having 30 chicks with 3 replicates of 10 chicks each. Chicks were reared under intensive conditions in houses that have a semi-controlled environment, with optimum temperature and adequate ventilation. Food and water were provided as per NRC (1994 requirement. Results: The average body weight after 6 weeks of the experiment was 2018.83±31.11, 1983.80±33.27, 2007.36±35.73, and 1938.43±36.35 g. The bedding type had no significant effect on the carcass characteristics viz. evisceration rate and proportion of cut-up parts of the carcass except giblet yield. The experiment suggested that performance of broiler chicks reared on paddy straw and pine leaves as litter material, had improved body weight and feed conversion ratio as compared to rearing on paddy husk as bedding material. Bacterial count, parasitic load and the N, P, K value of manure of different bedding material shows no significant difference. Conclusion: Pine leaves have a potential to be used as an alternative source of litter material to economize poultry production in a sustainable way, so as to make poultry farming as a profitable entrepreneur.

  14. Starting from Scratch: Greening Your Game Day--The Collegiate Football Sustainable Materials Management Toolkit. Version 1.0

    Science.gov (United States)

    Association for the Advancement of Sustainability in Higher Education, 2011

    2011-01-01

    The "Collegiate Football Sustainable Materials Management Toolkit" was researched by student interns in the Virginia Tech Office of Energy & Sustainability, developed in collaboration with the US EPA (US Environmental Protection Agency) and a national panel of technical experts from universities across the nation, and driven forward by CURC…

  15. Evaluation of Alternate Materials and Methods for Strontium and Alpha Removal from Savannah River Site High-Level Waste Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.T.

    2000-11-07

    A literature survey indicated a number of alternate materials and methods for the removal of strontium and alpha-emitting radionuclides (actinides). We evaluated the use of alternate materials versus proposed flowsheets for salt processing at the Savannah River Site (SRS). From this evaluation we recommend the following materials for further testing to determine the rate and extent of removal. We do not recommend testing of liquid/liquid extraction and polymer filtration methods at this time.

  16. Sequestration of phosphorus from wastewater by cement-based or alternative cementitious materials.

    Science.gov (United States)

    Wang, Xinjun; Chen, Jiding; Kong, Yaping; Shi, Xianming

    2014-10-01

    Cement-based and alternative cementitious materials were tested in the laboratory for their capability of removing phosphate from wastewater. The results demonstrated that both Langmuir and Freundlich adsorption isotherms were suitable for describing the adsorption characteristics of these materials. Among the four types of filter media tested, the cement-based mortar A has the highest value of maximum adsorption (30.96 mg g(-1)). The P-bonding energy (KL) and adsorption capacity (K) exhibited a positive correlation with the total content of Al2O3 and Fe2O3 in each mortar. The maximum amount of P adsorbed (Qm) and adsorption intensity (1/n) exhibited a positive correlation with the CaO content in each mortar. For three of them, the P-removal rates were in excess of 94 percent for phosphorus concentrations ranging from 20 to 1000 mg L(-1). The underlying mechanisms were examined using field emission scanning microscopy (FESEM), coupled with energy-dispersive X-ray spectroscopy (EDX) and X-ray powder diffraction (XRD). The results reveal that the removal of phosphate predominantly followed a precipitation mechanism in addition to weak physical interactions between the surface of adsorbent filter media and the metallic salts of phosphate. The use of cement-based or alternative cementitious materials in the form of ground powder shows great promise for developing a cost-effective and environmentally sustainable technology for P-sequestration and for wastewater treatment.

  17. Permafrost - An Alternative Target Material for Ultra High Energy Neutrino Detection?

    CERN Document Server

    Nahnhauer, R; Tosi, D

    2007-01-01

    The detection of cosmic neutrinos with energies above 1017 eV got growing interest during recent years. Possible target materials for in-matter arrays of ~100 km3 size under discussion are water, ice and rock salt. Here we propose to investigate permafrost as an additional alternative, covering ~20% of Earth land surface and reaching down to more than 1000 m depth at certain locations. If sufficiently large attenuation lengths for radio and acoustic signals can be demonstrated by in-situ measurements, the construction of a large hybrid array within this material may be possible in the Northern hemisphere. Properties and problems of a possible location in Siberia are discussed below. Some acoustic data are compared to laboratory measurements using "artificial" permafrost.

  18. Exciton Dynamics in Alternative Solar Cell Materials: Polymers, Nanocrystals, and Small Molecules

    Science.gov (United States)

    Pundsack, Thomas J.

    To keep fossil fuel usage in 2040 even with 2010 usage, 50% of global energy will need to come from alternative sources such as solar cells. While the photovoltaic market is currently dominated by crystalline silicon, there are many low-cost solar cell materials such as conjugated polymers, semiconductor nanocrystals, and organic small molecules which could compete with fossil fuels. To create cost-competitive devices, understanding the excited state dynamics of these materials is necessary. The first section of this thesis looks at aggregation in poly(3-hexylthiophene) (P3HT) which is commonly used in organic photovoltaics. The amount of aggregation in P3HT thin films was controlled by using a mixture of regioregular and regiorandom P3HT. Even with few aggregates present, excited states were found to transfer from amorphous to aggregate domains in fits and the most reasonable fitting parameters.

  19. Conceptual design report: Nuclear materials storage facility renovation. Part 6, Alternatives study

    International Nuclear Information System (INIS)

    The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL's weapons research, development, and testing (WRD ampersand T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL's inability to ship any materials offsite because of the lack of receiver sites for material and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. This report is organized according to the sections and subsections outlined by Attachment 111-2 of DOE Document AL 4700.1, Project Management System. It is organized into seven parts. This document, Part VI - Alternatives Study, presents a study of the different storage/containment options considered for NMSF

  20. Measurement of the resistivity of porous materials with an alternating air-flow method.

    Science.gov (United States)

    Dragonetti, Raffaele; Ianniello, Carmine; Romano, Rosario A

    2011-02-01

    Air-flow resistivity is a main parameter governing the acoustic behavior of porous materials for sound absorption. The international standard ISO 9053 specifies two different methods to measure the air-flow resistivity, namely a steady-state air-flow method and an alternating air-flow method. The latter is realized by the measurement of the sound pressure at 2 Hz in a small rigid volume closed partially by the test sample. This cavity is excited with a known volume-velocity sound source implemented often with a motor-driven piston oscillating with prescribed area and displacement magnitude. Measurements at 2 Hz require special instrumentation and care. The authors suggest an alternating air-flow method based on the ratio of sound pressures measured at frequencies higher than 2 Hz inside two cavities coupled through a conventional loudspeaker. The basic method showed that the imaginary part of the sound pressure ratio is useful for the evaluation of the air-flow resistance. Criteria are discussed about the choice of a frequency range suitable to perform simplified calculations with respect to the basic method. These criteria depend on the sample thickness, its nonacoustic parameters, and the measurement apparatus as well. The proposed measurement method was tested successfully with various types of acoustic materials.

  1. Incorporation of sugarcane bagasse ash waste as an alternative raw material for red ceramic

    Directory of Open Access Journals (Sweden)

    K. C. P. Faria

    2013-09-01

    Full Text Available The sugarcane industry generates huge amounts of sugarcane bagasse ashes (SCBA. This work investigates the incorporation of a SCBA waste as an alternative raw material into a clay body, replacing natural clay material by up to 20 wt.%. Clay ceramic pieces were produced by uniaxial pressing and fired at temperatures varying from 700 to 1100 ºC. The technological properties of the clay ceramic pieces (linear shrinkage, apparent density, water absorption, and tensile strength as function of the firing temperature and waste addition are investigated. The phase evolution during firing was followed by X-ray diffraction. The results showed that the SCBA waste could be incorporated into red ceramics (bricks and roofing tiles in partial replacement for natural clay material. These results confirm the feasibility of valorisation of SCBA waste to produce red ceramic. This use of SCBA can also contribute greatly to reducing the environmental problems of the sugarcane industry, and also save the sources of natural raw materials used in the ceramic industry.

  2. Refractories materials characterization for aluminum melting and holding furnaces: an alternative for a better performance

    International Nuclear Information System (INIS)

    The industrial needs in reducing the energy consumption is part of a continuing search towards higher levels of sustainability and competitiveness. Considering these aspects, the aluminum industry seeks new alternatives for a better performance of aluminum melting and holding furnaces and this aim is directly dependent on the refractory materials ability to conserve heat and withstand the mechanical, chemical and thermal degradation processes. This paper presents the thermo-mechanical characterization of five aluminous dense commercial refractory (average density of 2.7 g / cm ³), used in such equipment. The results indicated that choosing the most suitable composition requires the evaluation of the microstructure aspects, such as porosity, permeability and pore size, and also the refractory's physical integrity, such as thermal shock resistance, abrasion resistance and high temperature modulus of rupture. The laboratory tests allowed the characterization of all the materials at the same conditions. Moreover, it was possible to optimize the selection of lining materials for melting and holding furnaces and to provide basis to a possible costs improvements synergy. (author)

  3. Alternative free volume models and positron cages for the characterisation of nanoporosity in materials

    International Nuclear Information System (INIS)

    Three semi-empirical positron stationary Quantum Models were developed for the study of nanoporosity in a wide range of solid porous materials. The cubic, conic and cylindrical well potentials were considered and their geometric parameters related to the Positron Annihilation LifeTime (PALT) measurements. If a conic or a cubic symmetry is assumed, a resonance lifetime phenomenon was found, which enables proposal of a technique to catch positrons in free volume sites. In the cylindrical case, an alternative method to determine free volume sizes in materials was developed. The free volume equations of these new models were then compared to the well-known and widely utilised Spherical Free Volume Model (SFVM) and remarkable differences were found. A strong variation of the free volume size-positron lifetime relation with the geometry involved was observed and a remarkable dependence of the electron layer thickness parameter ΔR with the hole-shape under study and with the nature of the material considered. The mathematical functions appearing in the conic and cylindrical cases are the superposition of Bessel functions of the first kind and trigonometric functions in the cubic case. Generalised free volume diagrams were constructed and a brief geometrical scheme of the diverse cases considered was obtained. (author)

  4. Alternative approaches of SiC & related wide bandgap materials in light emitting & solar cell applications

    Science.gov (United States)

    Wellmann, Peter; Syväjärvi, Mikael; Ou, Haiyan

    2014-03-01

    Materials for optoelectronics give a fascinating variety of issues to consider. Increasingly important are white light emitting diode (LED) and solar cell materials. Profound energy savings can be done by addressing new materials. White light emitting diodes are becoming common in our lighting scene. There is a great energy saving in the transition from the light bulb to white light emitting diodes via a transition of fluorescent light tubes. However, the white LEDs still suffer from a variety of challenges in order to be in our daily use. Therefore there is a great interest in alternative lighting solutions that could be part of our daily life. All materials create challenges in fabrication. Defects reduce the efficiency of optical transitions involved in the light emitting diode materials. The donor-acceptor co-doped SiC is a potential light converter for a novel monolithic all-semiconductor white LED. In spite of considerable research, the internal quantum efficiency is far less than theoretically predicted and is likely a fascinating scientific field for studying materials growth, defects and optical transitions. Still, efficient Si-based light source represents an ongoing research field in photonics that requires high efficiency at room temperature, wavelength tuning in a wide wavelength range, and easy integration in silicon photonic devices. In some of these devices, rare earth doped materials is considered as a potential way to provide luminescence spanning in a wide wavelength range. Divalent and trivalent oxidation states of Eu provide emitting centers in the visible region. In consideration, the use of Eu in photonics requires Eu doped thin films that are compatible with CMOS technology but for example faces material science issues like a low Eu solid solubility in silica. Therefore approaches aim to obtain efficient light emission from silicon oxycarbide which has a luminescence in the visible range and can be a host material for rare earth ions. The

  5. BRC dosposal alternatives for NORM [naturally-occurring radioactive materials] wastes in Texas

    International Nuclear Information System (INIS)

    The Texas Low-Level Radioactive Waste Disposal Authority has investigated low-cost, alternative disposal methods for certain wastes containing small quantities of NORM. This paper presents a multipathway safety analysis of various scenarios for disposing of wastes containing limited quantities of naturally-occurring radioactive materials (NORM) in Texas. The wastes include pipe scales and sludges from oil and gas production, residues from rare-earth mineral processing, and water treatment resins, but exclude large-volume, diffuse waste. The purpose of the safety analysis to the define concentration and quantity limits for the key nuclides of NORM what will avoid dangerous radiation exposures under different waste disposal scenarios. 2 refs., 4 figs., 1 tab

  6. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    Directory of Open Access Journals (Sweden)

    Dipankar Sarkar

    2016-01-01

    Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

  7. Toenails as an alternative source material for the extraction of DNA from decomposed human remains.

    Science.gov (United States)

    Schlenker, Andrew; Grimble, Katelyn; Azim, Arani; Owen, Rebecca; Hartman, Dadna

    2016-01-01

    The DNA identification of decomposed human remains for coronial investigations at the Victorian Institute of Forensic Medicine routinely requires the retrieval and processing of a bone sample obtained from the deceased. Bone is a difficult sample type to work with as it requires surgical removal from the deceased, refrigerated storage, and additional processing steps prior to DNA analysis in comparison to other samples types such as buccal swabs or blood stains. In an attempt to overcome the issues posed by bone, a DNA extraction method utilising toenails as an alternate source material was optimised and trialled. Two DNA extraction methods were optimised for digestion of toenail material, with the method utilising the QIAGEN DNA Investigator Kit selected for a casework trial. Single source DNA profiles, matching those of the conventional samples taken, were obtained for toenail samples collected from 28 of 30 coronial cases available for this study. Of these, 26 toenail samples produced full profiles. Although the overall DNA profile quality from the toenails was less than that of the conventional sample, the profiles from toenails met the reporting requirements for identification. Based on the results obtained, the Victorian Institute of Forensic Medicine will be implementing toenails as the primary sample type for collection from decomposed remains when blood is not a suitable sample type. PMID:26610200

  8. Naturally Abundance Vanillin as Starting Material to Synthesizing 4-(4-Hydroxy-3-methoxyphenyl-6-methyl-3,4-dihydropyrimidin-2(1H-one

    Directory of Open Access Journals (Sweden)

    Masruri MASRURI

    2015-12-01

    Full Text Available Indonesia is the second biggest producer of natural vanillin. Traditionally it was isolated from the bean of vanilla (Vanilla planifolia Andrews. This paper reports on applying vanillin as starting material for synthesizing a biologically important chemical structure 3,4-dihydropyrimidinone. The reaction was undertaken in one step following multi component reaction (MCR. Products determination was undergone using FTIR and UV-Vis spectrophotometry, and also liquid chromatography-mass spectrometry (LCMS. After purification under flash column chromatography in ethyl acetate-hexane, it was found a white solid of 4-(4-hydroxy-3-methoxyphenyl-6-methyl-3,4-dihydropyrimidin-2(1H-one in 67% yield with a few amount of an unreacted vanillin.

  9. Single-tube-genotyping of gastric cancer related SNPs by directly using whole blood and paper-dried blood as starting materials

    Institute of Scientific and Technical Information of China (English)

    Huan Huang; Ying Bu; Guo-Hua Zhou

    2006-01-01

    AIM: To demonstrate an inexpensive method for typing gastric cancer related single nucleotide polymorphisms (SNPs) using whole blood or paper-dried blood as starting materials.METHODS: PCR amplification is directly carried out from the whole blood or paper-dried blood sample without any DNA extraction step. Before PCR, a blood sample, four primers, and all of biological reagents necessary for PCR were added at a time; After PCR, the amplified products were directly separated by slab gel electrophoresis or microchip CE without any purification. SNP typing was performed by tetra-primer PCR with two inner primers specific to each allele and two outer primers defining the length of allele-specific amplicons. Genotypes were directly discriminated by the size of amplicons specific to each allele, thereby avoiding any post-PCR process.RESULTS: Using a special PCR buffer, inhibitory substances in blood (including the anticoagulant in blood) and filter paper were effectively suppressed;a "true" single-tube-genotyping is thus realized. We successfully determined genotypes IL-1B-511 and IL-1B-31 polymorphisms at the gene IL-1B by using whole-blood and paper-dried blood samples as starting materials respectively. The method is so sensitive that 0.5-1.0 μL of blood sample is enough to give a satisfactory typing results. The genotyping results were confirmed by RFLP-PCR using purified genome DNA,indicating that amplification specificity was not affected by inhibitory components (including coagulants) in blood or filter paper.CONCLUSION: Compared with SNP typing methods based on purified DNA, the proposed method is laborsaving, simple, inexpensive, and less cross-contaminated.It is promising to use this method to type other SNPs.

  10. Alternative technological approach for synthesis of ceramic pigments by waste materials recycling

    Energy Technology Data Exchange (ETDEWEB)

    Doynov, M.; Dimitrov, T.; Kozhukharov, S.

    2016-05-01

    Alternative technological approach is proposed enabling utilization of raw materials from an oil refinery, such as waste guard layers from reactors. Reagent grade and purified MgO, Cr{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, and nitric acid (HNO{sub 3}), were used as additional precursors. The homogeneous mixtures obtained were formed into pellets and sintered at different temperatures. The main phase was proved by X-ray phase analysis (XRD) and compared to ICPDS database. The main phase in the ceramics synthesized was solid solution of spinel MgAl{sub 2}O{sub 4} and magnesiochromite. These minerals are classified as chromspinelide MgCr{sub 1}.2Al{sub 0}.4Fe{sub 0}.4O{sub 4} and alumochromite MgCr{sub 1}.6Al{sub 0}.4O{sub 4}. Additional SEM observations, combined with EDX analysis were performed, evincing agglomeration at lower temperatures, followed by agglomerate crumbling, at elevated calcination temperature. The complete transformation of initial precursors into the final ceramic compounds was found to occur at 800 degree centigrade 1 h. The ceramic samples synthesized had high density of 1.72-1.93 g/cm{sup 3} and large absorption area - 32.93% which is probably due to the high porosity of the sample. (Author)

  11. Investigation on the long-term radiation hardness of low resistivity starting silicon materials for RT silicon detectors in high energy physics

    Energy Technology Data Exchange (ETDEWEB)

    Li, Z.

    1994-02-01

    Relatively low resistivity (200 to 1000 {Omega}-cm) starting silicon materials have been studied in the search of room temperature neutron radiation-hard silicon detectors. It has been found that, moderate resistivity (300-700 {Omega}-cm) silicon detectors, after being irradiated to 5.0 {times} 10{sup 13} to 2.0 {times} 10{sup 14} n/cm{sup 2}, are extremely stable in terms of the detector full depletion voltage (V{sub d}) or the net effective concentration of ionized space charges (N{sub eff} ---- there is little ``reverse annealing`` of N{sub eff} at RT and elevated temperatures as compared with large reverse annealing observed for high resistivity silicon detectors. Detectors with starting resistivity of 300-700 {Omega}-cm have been found to be stable, during the equivalent of one year RT anneal that would reach the saturation of the first stage of reverse anneal, within then N{sub eff} window of {vert_bar}N{sub eff}{vert_bar}{le} 2.5 {times} 10{sup 12} cm{sup {minus}3} (V{sub d} = 180 V for d = 300 {mu}m) in a working range of 5.0 {times} 10{sup 13} to 1.5 {times} 10{sup 14} n/cm{sup 2}, or a net neutron radiation tolerance of 1.0 {times} 10{sup 14} n/cm{sup 2}. The observed effects are in very good agreement with an early proposed model, which predicted among others, that there might be an off set between the reverse annealing effect and the partial annealing of the P-V centers that leads to the partial recovery of the shallow impurity donors.

  12. Reducing cold-start emission from internal combustion engines by means of a catalytic converter embedded in a phase-change material

    Energy Technology Data Exchange (ETDEWEB)

    Korin, E. [Ben-Gurion Univ. of the Negev, Dept. of Chemical Engineering, Beer-Sheva (Israel); Reshef, R.; Tschernichovesky, D.; Sher, E. [Ben-Gurion Univ. of the Negev, Dept. of Mechanical Engineering, Beer-Sheva (Israel)

    1999-11-01

    Under normal operating conditions, catalytic converters appear to be the most effective means of reducing air pollution from internal combustion (IC) engines. The conversion efficiency, however, declines very steeply for temperatures below about 350degC and is practically zero during the starting and warming-up period. Improving the conversion efficiency under these conditions is important, particularly in large cities, where the number of startings per vehicles per day tend to be high. Among the more successful solutions are preheating of the catalyst electrically, warming up of the catalyst in an external combustion chamber, installation of an auxiliary small-capacity catalytic converter, and employment of an adsorbing unit between two catalysts. Although these methods are quite effective, their disadvantage lies in the fact that they require an external energy source, an additional component (a control unit) or a three-stage catalyst. In the present work an investigation was made of a solution based on the exploitation of thermal capacitance to keep the catalyst temperature high during off-operation periods. A phase-change material (PCM) with a transition temperature of 352.7degC, which is slightly above the light-off temperature of the metallic catalyst, was specially formulated, and a system comprising a catalytic converter embedded in the PCM was designed and tested. Under normal engine operating conditions, some of the thermal energy of the exhaust gases was stored in the PCM. During the time that the vehicle was not in use, the PCM underwent partial solidification, and the latent heat thus produced was exploited to maintain the catalyst temperature within the desired temperature range for maximum conversion efficiency. (Author)

  13. PEM Fuel Cell Freeze Durability and Cold Start Project

    Energy Technology Data Exchange (ETDEWEB)

    Patterson, T.; O' Neill, Jonathan

    2008-01-02

    UTC has taken advantage of the unique water management opportunities inherent in micro-porous bipolar-plates to improve the cold-start performance of its polymer electrolyte fuel cells (PEFC). Diagnostic experiments were used to determine the limiting factors in micro-porous plate PEFC freeze performance and the causes of any performance decay. Alternative cell materials were evaluated for their freeze performance. Freeze-thaw cycling was also performed to determine micro-porous plate PEFC survivability. Data from these experiments has formed the basis for continuing development of advanced materials capable of supporting DOE's cold-start and durability objectives.

  14. Production of carbonaceous material from avocado peel for its application as alternative adsorbent for dyes removal

    Institute of Scientific and Technical Information of China (English)

    Carolyn Palma; Lucia Lloret; Antonio Puen; Maira Tobar; Elsa Contreras

    2016-01-01

    Adsorption processes have received special attention for contaminants removal thanks to their capability to gen-erate effluents with high quality as well as their simple design. In the current work, the agro-waste residue avo-cado peel is proposed to be used as alternative to conventional activated carbons whose use is sometimes restricted to high costs, upgraded by their exhausting after long term operations. The carbonization procedure was optimized and analyzed through factorial design and response surface methodology by evaluating temper-ature (400–900 °C) and time (30–90 min) effects:optimal conditions were found at 900 °C and 65 min, gener-ating an adsorbent with 87.52 m2·g−1 of BET surface area, a mesopore volume of 74%and a zero point charge at 8.6. The feasibility of the carbonaceous material was proved for the removal of a variety of dyes by investigating substrate (10–50 mg·L−1) and solid (0.5–20 g·L−1) concentration effects and statistical significance:complete removal of Naphthol Blue Black and Reactive Black 5 was reached under optimal conditions (10 mg·L−1 and 20 g·L−1 of dye and solid, respectively), while Basic Blue 41 was eliminated by using 13.4 g·L−1 of the adsorbent. Overal , dyes removal by adsorption on carbonized avocado peel is presented as a promising technology due to the low cost and easy availability of the precursor, as well as the straightforward generation, the satisfactory char-acteristics and the proved adsorption capacity of the adsorbent.

  15. Multi-wall carbon nanotubes/epoxy resin composites characterization of the starting materials and evaluation of thermal and electrical conductivity

    International Nuclear Information System (INIS)

    In this study we investigate the electrical and thermal properties of I) composite materials fabricated with O, I, 0,5 and I wt% of concentric multi-wall carbon nanotubes/epoxy resin (MWNT) dispersed randomly in the resin; 2) MWNT buckypaper/resin composite materials; 3) and neat MWNT buckypaper. Initially, we use the techniques of thermogravimetry, infrared spectroscopy, nuclear magnetic resonance, energy dispersive spectroscopy, x-ray fluorescence, scanning and transmission electron microscopy for a broadening characterization of the starting materials, to evaluate its morphology, purity, chemical composition and structure, in order to optimize the properties of crosslinked resin and, consequently, of the composite systems. Important parameters such as the average molecular mass and the equivalent weight of epoxy resin (DGEBA) were determined by 1H-NMR analysis and, after that, resin/curing agent relations with Phr 10, 15, 20 and 53,2 were elaborated and investigated by thermogravimetry, the resin/curing agent relation with Phr 10 showed to be the most thermally stable. This stoichiometric relation was used to elaborate the composites. We have evaluated that the effect of adding 10 wt% of the solvent acetone to the epoxy resin preparation does not alter its properties so we have adopted two routes to fabricate the composites. In the first route we used 10 wt% of acetone and, in the second the MWNT were dispersed in the matrix without using the solvent. However, no significant difference was observed for the dispersion of the bundle tubes in both systems. The electrical conductivity of the composites and buckypapers was evaluated by impedance spectroscopy and the thermal conductivity by the flash laser flash method. Only the buckypapers presented high values for electrical conductivity (103 S.m-1). The composite systems presented values of 10-3 S.m-1, only a bit different from the value of the crosslinked resin. For thermal conductivity, the values for the

  16. F- and H-Area Seepage Basins Water Treatment System Process Optimization and Alternative Chemistry Ion Exchange/Sorbent Material Screening Clearwell Overflow Study

    Energy Technology Data Exchange (ETDEWEB)

    Serkiz, S.M.

    2000-08-30

    This study investigated alternative ion exchange/sorbent materials and polishing chemistries designed to remove specific radionuclides not removed during the neutralization/precipitation/clarification process.

  17. Effects of Parameter Modulation on Near-Field Imaging in Photonic Crystal Consisting of Alternately Left-Handed Material and Right-Handed Material

    Institute of Scientific and Technical Information of China (English)

    WANG Qiong; YAN Chang-Chun; ZHANG Ling-Ling; CUI Yi-Ping

    2008-01-01

    @@ By means of the transfer-matrix method, the effects of parameter modulation on the quality of near-field imaging in one-dimensional photonic crystal consisting of alternately Lett-handed material and right-handed material are investigated.Based on analyses of the recovery rate and ph'ase shift, the results show that the imaging quality is not obviously affected by the minor changes of layer thickness.In addition, by modulating the material parameters of the Lett-handed material, it is found that for both the real part and the imaginary part, the system is more sensitive to the permeability than the permittivity for the TE wave.For the TM wave, it is reverse.These properties are very useful to fabricate Lett-handed material photonic crystals in practice.

  18. Data summary of municipal solid waste management alternatives. Volume 7, Appendix E -- Material recovery/material recycling technologies

    Energy Technology Data Exchange (ETDEWEB)

    None

    1992-10-01

    The enthusiasm for and commitment to recycling of municipal solid wastes is based on several intuitive benefits: Conservation of landfill capacity; Conservation of non-renewable natural resources and energy sources; Minimization of the perceived potential environmental impacts of MSW combustion and landfilling; Minimization of disposal costs, both directly and through material resale credits. In this discussion, ``recycling`` refers to materials recovered from the waste stream. It excludes scrap materials that are recovered and reused during industrial manufacturing processes and prompt industrial scrap. Materials recycling is an integral part of several solid waste management options. For example, in the preparation of refuse-derived fuel (RDF), ferrous metals are typically removed from the waste stream both before and after shredding. Similarly, composting facilities, often include processes for recovering inert recyclable materials such as ferrous and nonferrous metals, glass, Plastics, and paper. While these two technologies have as their primary objectives the production of RDF and compost, respectively, the demonstrated recovery of recyclables emphasizes the inherent compatibility of recycling with these MSW management strategies. This appendix discusses several technology options with regard to separating recyclables at the source of generation, the methods available for collecting and transporting these materials to a MRF, the market requirements for post-consumer recycled materials, and the process unit operations. Mixed waste MRFs associated with mass bum plants are also presented.

  19. Predicted concentrations in new relocatable classrooms of volatile organic compounds emitted from standard and alternate interior finish materials

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, Alfred T.; Fisk, William J.; Shendell, Derek G.; Apte, Michael G.

    2001-07-01

    Relocatable classrooms (RCs) are widely employed by California school districts to satisfy rapidly expanding space requirements due to population growth and class size reduction policies. There is public concern regarding indoor environmental quality (IEQ) in schools, particularly in RCs, but very little data to support or dispel these concerns. Several studies are investigating various aspects of IEQ in California schools. This laboratory-based study focused on evaluating the emissions of toxic and/or odorous volatile organic compounds (VOCs), including formaldehyde and acetaldehyde, from materials used to finish the interiors of new RCs. Furthermore, the study implemented a procedure for VOC source reduction by testing and selecting lower-emitting materials as substitutes for standard materials. In total, 17 standard and alternate floor coverings, wall panels and ceiling panels were quantitatively tested for emissions of VOCs using smallscale environmental chambers. Working with the largest northern California manufacturer of conventional RCs and two school districts, specifications were developed for four new RCs to be produced in early summer 2001. Two of these will be predominantly finished with standard materials. Alternate carpet systems, an alternate wall panel covering and an alternate ceiling panel were selected for the two other RCs based on the results of the laboratory study and considerations of cost and anticipated performance and maintenance. Particular emphasis was placed on reducing the concentrations of VOCs on California agency lists of toxic compounds. Indoor concentrations of toxic and odorous VOCs were estimated for the four classrooms by mass balance using the measured VOC emission factors, exposed surface areas of the materials in the RCs, and three ventilation rate scenarios. Results indicate that reductions in the concentrations of formaldehyde, acetaldehyde phenol, di(ethylene glycol) butyl ether, vinyl acetate, 1,2,4-trimethylbenzene

  20. Formation of Mg{sub 2}Ni with enhanced kinetics: Using MgH{sub 2} instead of Mg as a starting material

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Bin [Department of Materials Science, Fudan University, Shanghai 200433 (China); School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002 (China); Fang Fang [Department of Materials Science, Fudan University, Shanghai 200433 (China); Sun Dalin, E-mail: dlsun@fudan.edu.cn [Department of Materials Science, Fudan University, Shanghai 200433 (China); Zhang Qingan [School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002 (China); Wei Shiqiang [National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei 230029 (China); Cao Fenglei; Sun Huai [Department of Chemistry, Shanghai Jiaotong University, Shanghai 200240 (China); Ouyang Liuzhang [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Zhu Min, E-mail: memzhu@scut.edu.cn [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China)

    2012-08-15

    At a temperature over the decomposition point (375 Degree-Sign C) of MgH{sub 2}, the formation of Mg{sub 2}Ni is greatly enhanced from the 2MgH{sub 2}+Ni system, as compared to the 2Mg+Ni system. In support of this finding, in-situ observation of X-ray absorption fine structure of the two systems indicates that Mg---Ni bonds form faster in the 2MgH{sub 2}+Ni system than in the 2Mg+Ni system. Furthermore, theoretical modeling also shows that Mg atoms are readily released from MgH{sub 2} using much less energy and thus are more available to react with Ni once the dehydrogenation of MgH{sub 2} occurs, as compared to normal Mg. - Graphical Abstract: The formation of Mg{sub 2}Ni is greatly enhanced by using MgH{sub 2} instead of Mg at a temperature higher than the MgH{sub 2} decomposition point. Highlights: Black-Right-Pointing-Pointer A new and efficient synthesis of Mg-based compounds at a reduced temperature. Black-Right-Pointing-Pointer Mg{sub 2}Ni formation is enhanced by using MgH{sub 2} instead of Mg as a starting material. Black-Right-Pointing-Pointer XAFS results show that Mg---Ni bonds are formed faster in 4MgH{sub 2}+Ni than in 4Mg+Ni. Black-Right-Pointing-Pointer DFT calculations show that Mg atoms are released from MgH{sub 2} more readily than from Mg. Black-Right-Pointing-Pointer Mg formed by MgH{sub 2} dehydrogenation is more available to react with Ni than normal Mg.

  1. Potential Use Of Carbide Lime Waste As An Alternative Material To Conventional Hydrated Lime Of Cement-Lime Mortars

    OpenAIRE

    Al Khaja, Waheeb A.

    1992-01-01

    The present study aimed at the possibility of using the carbide lime waste as an alternative material to the conventional lime used for cement-lime mortar. The waste is a by-product obtained in the generation of acetylene from calcium carbide. Physical and chemical properties of the wastes were studied. Two cement-lime-sand mix proportions containing carbide lime waste were compared with the same mix proportions containing conventional lime along with a control mix without lime. Specimens wer...

  2. 硅基沸石滤料A/O生物滤池挂膜启动的研究%Study on the Start-up of A/O Biofilm Process With Silicon-based Zeolite Filter Material

    Institute of Scientific and Technical Information of China (English)

    王娟婷; 刘振亮; 于衍真

    2014-01-01

    通过研究分析硅基沸石滤料A/O生物滤池的挂膜启动,以及考察系统出水CODCr、氨氮和总氮浓度在挂膜启动过程中的变化,分析挂膜启动的发展进程,寻求判断挂膜启动完成的合理理化指标,以期为A/O生物滤池的挂膜启动提供理论依据。%The start-up of A/O bio-filter was studied and reasonable indexs for the judgment of the start-up were found to provide the theory basis for the start-up of A/O bio-filter with silicon-based zeolite filter material. The study makes use of the natural start-up compound with inoculum start-up. The start-up of A/O bio-filter with silicon-based zeolite filter material was investigated by measuring the concentrations of CODCr, ammonia and total nitrogen in the effluent.

  3. An alternative testmethod for the bacterial barrier properties of wrapping materials

    NARCIS (Netherlands)

    van Asten JAAM; de Bruijn ACP

    1990-01-01

    The National Control Laboratory of the RIVM has performed a series of tests on different wrapping materials to demonstrate that a proposed test for dry bacteria tightness can be used for all different wrapping materials and methods. The test has been used on paper, textile, non-woven and containers

  4. Embodied Energy Assessment and Comparisons for a Residential Building Using Conventional and Alternative Materials in Indian Context

    Science.gov (United States)

    Naveen Kishore, K.; Chouhan, J. S.

    2014-06-01

    Building sector is responsible for 40 % of the primary energy use and 24 % of carbon dioxide emissions in India. The main source of green house gas emissions from buildings is due to energy consumption. This paper aims to assess the embodied energy index and environmental impact of a two storied residential building. The study proposes various alternative materials which can be used in day to day construction in order to mitigate the environmental impact and climate change due to construction activity in India. Two types of construction techniques have been considered for the study, namely load bearing and reinforced concrete framed construction. Embodied energy and carbon dioxide emissions of walling and roofing components using conventional and alternative materials has also been analyzed and compared. The comparison is done based on two parameters namely, embodied energy/m2 and CO2 emissions per unit of floor area. The study shows that bricks, cement and steel are the three major contributors to the energy cost of constructing a building by conventional methods. A conventional two storied load bearing structure is 22 % more energy efficient when compared to a reinforced concrete structure. It has also been observed from the study that use of alternative material in the building envelope gives embodied energy savings between 50 and 60 % for a two storey load bearing structure and 30-42 % for a two storey reinforced concrete structure. Hence a load bearing construction is certainly a better alternative to RC framed construction for up to two storied structures in terms of embodied energy and environmental impacts.

  5. Two Issues in Premise Plumbing: Contamination Intrusion at Service Line and Choosing Alternative Plumbing Material

    OpenAIRE

    Lee, Juneseok

    2008-01-01

    Worldwide water distribution infrastructure system is old and deteriorating. A water system with its myriad appurtenances (including pumps and valves and tanks) is susceptible to hydraulic transients resulting in high and low pressure waves alternatively passing through the network. While both low and high pressure events structurally tax the already weak system, there is copious evidence indicating intrusion of contaminants into the drinking water pipes from the pipeâ s exterior environment...

  6. Nonproliferation and arms control assessment of weapons-usable fissile material storage and excess plutonium disposition alternatives

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    This report has been prepared by the Department of Energy`s Office of Arms Control and Nonproliferation (DOE-NN) with support from the Office of Fissile Materials Disposition (DOE-MD). Its purpose is to analyze the nonproliferation and arms reduction implications of the alternatives for storage of plutonium and HEU, and disposition of excess plutonium, to aid policymakers and the public in making final decisions. While this assessment describes the benefits and risks associated with each option, it does not attempt to rank order the options or choose which ones are best. It does, however, identify steps which could maximize the benefits and mitigate any vulnerabilities of the various alternatives under consideration.

  7. Different drying technologies and alternation of mycobiots in the raw material of Hyssopus officinalis L.

    Science.gov (United States)

    Raila, Algirdas; Lugauskas, Albinas; Kemzūraite, Aurelija; Zvicevicius, Egidijus; Ragazinskiene, Ona; Railiene, Marija

    2009-01-01

    Contamination of medicinal plant mass with mycobiots is one of the negative factors deteriorating the quality of raw material. In order to evaluate the impact of the yield processing technologies upon the changes of mycobiots in raw material, the mycobiotic conditions of herb hyssop (Hyssopus officinalis L.) raw material were evaluated under various regimes of active ventilation and optimization of the drying parameters. The impact of ventilation intensity and temperature of drying agent upon the changes and abundance of mycobiota species in medicinal raw material was determined. Irrespective of the temperature of the airflow, the strongest suppressive effect upon the mycobiotic contamination in Hyssopi herba was produced by the 5,000 m3 x (t x h)(-1) airflow. Analysis of the isolated fungi revealed the prevalence of Penicillium, Aspergillus, Alternaria, Cladosporium, Mucor, Rhizopus species in the raw material. In separate samples Botrytis cinerea, Sclerotinia sclerotiorum, Aureobasidium pullulans, Chrysosporium merdarium, Cladorrhinum foecundissimum, Ulocladium consortiale, Trichoderma hamatum, T. harzianum, Gilmaniella humicola, Talaromyces flavus, Rhizomucor pusillus, Hansfordia ovalispora, Verticicladium trifi dum, Trichosporiella cerebriformis micromycetes were also rather abundant. Detection of the above-mentioned micromycetes in herb hyssop samples differed, and partially depended upon the medium used for their isolation. PMID:19630202

  8. Alternatives to Conventional Construction Materials on Landfills. A Guide; Alternativa konstruktionsmaterial paa deponier. Vaegledning

    Energy Technology Data Exchange (ETDEWEB)

    Rihm, Thomas; Rogbeck, Yvonne; Svedberg, Bo; Eriksson, Maria

    2009-03-15

    Before a landfill can be sited, an application for a permit from the authorities is required. Already in the application process the consequences concerning impact on human health and on the environment must be described, including descriptions of e.g. bottom liners and capping constructions. Since there is a long period of time between when the permit is given and when the capping will be carried out, it is common practice, either to postpone decisions concerning capping details, or to delegate the decisions to the supervisory authorities to be made at a later stage. All constructions must however be approved by the authorities before they can be carried out. A construction must fulfil the demands for its function. For the capping this means that the percolation through it must be low, even in a long time perspective. A construction may not in itself cause adverse environmental effects, e.g. leaching of hazardous substances from the construction material. Thus, there are functional as well as environmental demands. Beside the functional demands given in the Swedish legislation, notably in the ordinance on landfilling, the construction must be physically stable, also in a long time perspective. The materials in the construction must have sufficient strength, and may not change over time, e.g. due to degradation, which could lead to malfunction. Demands on environmental behaviour can be divided into two parts. Humans and animals must be kept from direct contact with dangerous substances including dermal contact, inhalation of dust or gases and oral intake of soil, plants or berries. Secondly, dangerous substances may not be spread with surface or ground water to an extent that could lead to adverse effects on human health or on the environment. The impact on the environment is not only depending of the materials being used, but also on the construction design, where in the landfill the construction is situated and, not least, how the landfill is located. It is

  9. Incinerated sewage sludge ash as alternative binder in cement-based materials

    DEFF Research Database (Denmark)

    Krejcirikova, Barbora; Goltermann, Per; Hodicky, Kamil

    2013-01-01

    Sewage sludge ash is characterized by its pozzolanic properties, as cement is. This predetermines its use in a substitution of cement and cementitious materials. Utilization of sewage sludge ash does not only decrease the consumption of cement, one of the largest cause of CO2 emissions, but also...

  10. Development of alternating current transmitter of detection system for magnetic material in soil subsurface

    Science.gov (United States)

    Indrasari, Widyaningrum; Djamal, Mitra; Srigutomo, Wahyu; Ramli

    2016-03-01

    Generally, detection system for magnetic material in soil subsurface using electromagnetic induction method consists of two parts, they are transmitter and receiver unit. A transmitter must be able to produce a continuous and stable AC current at a certain frequency, meanwhile receiver should be able to catch the secondary magnetic field of magnetic material in soil subsurface. The aim of this study was to develop a new AC current transmitter of detection system for the magnetic material in soil subsurface. This paper will describe the results of the development of AC current transmitter systems, distance characterization of the sensor detection toward horizontal solenoid positions, and characterization of magnetic material in the soil subsurface. It has successfully made the AC current transmitter system, composed of a sinusoidal signal generator, power amplifier, and a source of AC magnetic field. The output of the generator has a frequency varies: 1 kHz, 2 kHz, 5 kHz, and 10 kHz. We found that the AC current transmitter that has been developed able to work properly up to a frequency of 10 kHz.

  11. The Relation between Life Satisfaction and the Material Situation: A Re-Evaluation Using Alternative Measures

    Science.gov (United States)

    Christoph, Bernhard

    2010-01-01

    Among the surprising results of research on the relation between a person's material circumstances and his or her subjective well-being was the finding that this relationship appears to be rather weak (throughout this paper the terms "(general) life satisfaction", "(subjective) satisfaction", "happiness" and "subjective well-being" will be used…

  12. Evaluation of alternative phase change materials for energy storage in solar dynamic applications

    Science.gov (United States)

    Crane, R. A.; Dustin, M. O.

    1988-01-01

    The performance of fluoride salt and metallic thermal energy storage materials are compared in terms of basic performance as applied to solar dynamic power generation. Specific performance considerations include uniformity of cycle inlet temperature, peak cavity temperature, TES utilization, and system weights. Also investigated were means of enhancing the thermal conductivity of the salts and its effect on the system performance.

  13. Pumping through porous hydrophobic/oleophilic materials: an alternative technology for oil spill remediation.

    Science.gov (United States)

    Ge, Jin; Ye, Yin-Dong; Yao, Hong-Bin; Zhu, Xi; Wang, Xu; Wu, Liang; Wang, Jin-Long; Ding, Hang; Yong, Ni; He, Ling-Hui; Yu, Shu-Hong

    2014-04-01

    Recently, porous hydrophobic/oleophilic materials (PHOMs) have been shown to be the most promising candidates for cleaning up oil spills; however, due to their limited absorption capacity, a large quantity of PHOMs would be consumed in oil spill remediation, causing serious economic problems. In addition, the complicated and time-consuming process of oil recovery from these sorbents is also an obstacle to their practical application. To solve the above problems, we apply external pumping on PHOMs to realize the continuous collection of oil spills in situ from the water surface with high speed and efficiency. Based on this novel design, oil/water separation and oil collection can be simultaneously achieved in the remediation of oil spills, and the oil sorption capacity is no longer limited to the volume and weight of the sorption material. This novel external pumping technique may bring PHOMs a step closer to practical application in oil spill remediation.

  14. Investigation of alternative materials for impregnation of $Nb_{3}$ Sn magnets

    CERN Document Server

    Chichili, D R; Zlobin, A V

    2003-01-01

    Insulation is one of the most important elements of magnet design, which determines the electrical, mechanical, and thermal performance as well as lifetime of the magnet. The exposure to high radiation loads especially for the proposed LHC second-generation interaction region Nb/sub 3/Sn quadrupoles further limits the choices of the insulation materials. Traditionally Nb/sub 3/Sn magnets were impregnated with epoxy to improve both the mechanical and electrical properties. However, the acceptable radiation limit for epoxy is low which reduces the lifetime of the magnet. The paper presents the results of the feasibility study to replace epoxy with high radiation-resistant material during vacuum impregnation. The mechanical, thermal and electrical properties of samples impregnated with Matrimid were measured and compared with epoxy-impregnated samples. (9 refs).

  15. Assessment outcome is weakly correlated with lecture attendance: influence of learning style and use of alternative materials.

    Science.gov (United States)

    Horton, Dane M; Wiederman, Steven D; Saint, David A

    2012-06-01

    The relation between lecture attendance and learning is surprisingly weak, and the role of learning styles in this is poorly understood. We hypothesized that 1) academic performance is related to lecture attendance and 2) learning style influences lecture attendance and, consequently, affects performance. We also speculated that the availability of alternative resources would affect this relationship. Second-year Bachelor of Science physiology students (n = 120) self-reported their lecture attendance in a block of 21 lectures (attendance not compulsory) and use of alternative resources. Overall self-reported lecture attendance was 73 ± 2%. Female students (n = 71) attended more lectures (16.4 ± 0.6) than male students (14.3 ± 0.08, n = 49) and achieved a higher composite mark in all assessments (73.6% vs. 69.3%, P reading/writing, and K is kinesthetic), students were multimodal, although female students had a slightly higher average percentage of the R learning style (preferred read/write) compared with male students (28.9 ± 0.9%, n = 63, vs. 25.3 ± 1.3%, n = 32, P < 0.03). Lecture attendance was not correlated with measured learning style. We concluded that lecture attendance is only weakly correlated with academic performance and is not related to learning style. The substitution of alternative materials for lecture attendance appears to have a greater role than learning style in determining academic outcomes.

  16. The Thermochemical Degradation of Hot Section Materials for Gas Turbine Engines in Alternative-Fuel Combustion Environments

    Science.gov (United States)

    Montalbano, Timothy

    Gas turbine engines remain an integral part of providing the world's propulsion and power generation needs. The continued use of gas turbines requires increased temperature operation to reach higher efficiencies and the implementation of alternative fuels for a lower net-carbon footprint. This necessitates evaluation of the material coatings used to shield the hot section components of gas turbines in these new extreme environments in order to understand how material degradation mechanisms change. Recently, the US Navy has sought to reduce its use of fossil fuels by implementing a blended hydroprocessed renewable diesel (HRD) derived from algae in its fleet. To evaluate the material degradation in this alternative environment, metal alloys are exposed in a simulated combustion environment using this blended fuel or the traditional diesel-like fuel. Evaluation of the metal alloys showed the development of thick, porous scales with a large depletion of aluminum for the blend fuel test. A mechanism linking an increased solubility of the scale to the blend fuel test environment will be discussed. For power generation applications, Integrated Gasification Combined Cycle (IGCC) power plants can provide electricity with 45% efficiency and full carbon capture by using a synthetic gas (syngas) derived from coal, biomass, or another carbon feedstock. However, the combustion of syngas is known to cause high water vapor content levels in the exhaust stream with unknown material consequences. To evaluate the effect of increased humidity, air-plasma sprayed (APS), yttria-stabilized zirconia (YSZ) is thermally aged in an environment with and without humidity. An enhanced destabilization of the parent phase by humid aging is revealed by x-ray diffraction (XRD) and Raman spectroscopy. Microstructural analysis by transmission electron microscopy (TEM) and scanning-TEM (STEM) indicate an enhanced coarsening of the domain structure of the YSZ in the humid environment. The enhanced

  17. Raw materials, energy, water. Air pollution, ecological nutrition, alternatives to nuclear energy

    International Nuclear Information System (INIS)

    ''Ecological cattle breeding: A climate killer''. This was the title of an article in ''Frankfurter Rundschau'' journal, which summarized the findings of a study according to which ecological cattle breeding is more harmful to the environment than conventional cattle breeding, not least because eco-cattle live longer and are kept according to the principles of organic farming. This special issue of OeKO-TEST goes into detail about ecological nutrition. After all, animal farming accounts for 18 percent of the global climate-relevant gaseous emissions. A closer look will show that ecological cattle breeding is not a climate killer but that ecological farming and nutrition may even help in the fight against global climate change. In fact, this has been known all along, as are other strategies to prevent global warming. Thirty years ago, the Oeko-Institut, Freiburg, published a concept to prevent global climate change that is still up to date. It comprises energy conservation, rational energy use, and the utilization of alternative energy sources. If these concepts had been followed then and there, we would not have the problems of global climate change and rising energy cost today. We all know how to save this planet and how to prevent the dying out of species, the pollution of the oceans and air, and the destruction of forests. It is up to us to do it. (orig.)

  18. Development of an alternate pathway for materials destined for disposition to WIPP

    Energy Technology Data Exchange (ETDEWEB)

    Ayers, Georgette Y [Los Alamos National Laboratory; Mckerley, Bill [Los Alamos National Laboratory; Veazey, Gerald W [Los Alamos National Laboratory; Ricketts, Thomas E [Los Alamos National Laboratory

    2010-01-01

    The Los Alamos National Laboratory currently has an inventory of process residues that may be viable candidates for disposition to the Waste Isolation Pilot Project (WIPP) located at Carlsbad, New Mexico. A recent 'Attractiveness Level D' exemption allows for the discard of specified intractable materials regardless of the percent plutonium. However, the limits with respect to drum loadings must be met. Cementation is a key component of the aqueous nitrate flowsheet and serves as a 'bleed-off' stream for impurities separated from the plutonium during processing operations. The main 'feed' to the cementation operations are the 'bottoms' from the evaporation process. In the majority of cases, the cemented bottoms contain less than the allowed amount per drum for WIPP acceptance. This project would expand the route to WIPP for items that have no defined disposition path, are difficult to process, have been through multiple passes, have no current recovery operations available to recover the plutonium and that are amenable to cementation. This initial work will provide the foundation for a full scale disposition pathway of the candidate materials. Once the pathway has been expanded and a cementation matrix developed, routine discard activities will be initiated.

  19. THE USE OF COMPOSIT MATERIALS ALTERNATIVE FIBERGLASS (COCO FIBERS & RAGS ON FIBERGLASS SHIP IN TRADITIONAL SHIPYARDS BENGKALIS REGENCY

    Directory of Open Access Journals (Sweden)

    Romadhoni Oni

    2015-08-01

    Full Text Available The limitations of the current wood raw material nowadays is  a threat to the traditional shipbuilding business. Besides the material is expensive, it is also about the difficulty in bringing the major raw materials, fiberglass, suchas wood fiber MAT and WR ( Woven Roofing. There is plan issues to ban on the use of the fiber within a certain period  that accelerate the research in making the solution to be environment- free fiber. By doing the mechanical testing of coco fibre and rags, then gained streghth the bending and optimal impact and eligible BKI standard and ASTM D- 790 and ASTM D 638 and also the use of fiberglass reinforcement material fiber alternative is expected to save expenses in making that fiberglass. To reduce the environmental waste product that do not decompose in maintaining our health (avoiding toxic substances against syntetic fiber. The result of bending test of composit and coir fabric is getting by using Bending Elasticity Modulus with average rags of hijab 12,88 Mpa, coco fibre 2,69 Mpa and fiber fabric undershirt 6, 57 Mpa, whereas  for testing the impact obtained average value of rags hijab 0,0808 kg/mm2 coco fibiers-0,16533 kg/mm2 and fiber fabric undershit 0, 00427 kg/mm2

  20. Development and evaluation of alternative radioanalytical methods, including mass spectrometry for marine materials

    International Nuclear Information System (INIS)

    One, if not the most important, aspect of environmental protection against radioactive contamination is the ability to measure accurately low-levels of radionuclides present in the environment. This is particularly true of the marine environment where improved and more rapid methods of analysis are required to identify the source and radiological impact of anthropogenic inputs to the oceans. More sensitive and rapid analytical methods with smaller analytical errors are required to study the behaviour of different radionuclides in the marine environment. Some of these radionuclides serve as useful research tracers that aid in understanding many complex oceanographic processes. With the ever-increasing demand for more accurate data, the IAEA considered it necessary to convene an Advisory Group Meeting to identify those long-lived radionuclides that may be measured by alternative techniques and discuss and evaluate the sensitivity of the analytical methods. The meeting was held at the IAEA Marine Environment Laboratory in Monaco from 6 to 9 June 1989 and was attended by 6 invited participants and several observers. This report from the meeting is divided into two parts. The first contains 5 contributing chapters. In these chapters the authors have endeavored to explain the principles of each measurement technique, the strengths and weakness of the method as applied to marine sciences, comparative costs and sensitivities, future developments and topics of interest to the Agency. The reviews and sensitivities were prepared exclusively by the participants on the basis of their own experience and knowledge of the existing literature. The second part of this report is the appendices section in which can be found tables of radionuclides considered in this report and a comparison of sensitivities for different methods of detection. Refs, figs and tabs

  1. Determination of allowable fluid temperature during start-up operation of outlet header under the assumption of constant and temperature-dependent material properties

    Science.gov (United States)

    Rząsa, Dariusz; Duda, Piotr

    2013-09-01

    Modern supercritical power plants operate at very high temperatures and pressures. Thus the construction elements are subjected to both high thermal and mechanical loads. As a result high stresses in those components are created. In order to operate safely, it is important to monitor stresses, especially during start-up and shut-down processes. The maximum stresses in the construction elements should not exceed the allowable stresses that are defined according to boiler regulations. It is important to find optimum operating parameters, that can assure safe heating and cooling processes. The optimum parameters define temperature and pressure histories that can keep the highest stresses within allowable limit and reduce operation time as much as possible. In this paper a new numerical method for determining optimum working fluid parameters is presented. In this method, properties of steel can be assumed as constant or temperature dependent. The constant value is taken usually at the average temperature of the operation cycle. For both cases optimal parameters are determined. Based on these parameters start-up operations for both cases are conducted. During entire processes stresses in the heated element are monitored. The results obtained are compared with German boiler regulations - Technische Regeln fur Dampfkessel 301.

  2. Off-Hugoniot characterization of alternative inertial confinement fusion ablator materials.

    Science.gov (United States)

    Moore, Alastair S.; Prisbrey, Shon; Baker, Kevin L.; Celliers, Peter M.; Fry, Jonathan; Dittrich, Thomas R.; Wu, Kuang-Jen J.; Kervin, Margaret L.; Schoff, Michael E.; Farrell, Mike; Nikroo, Abbas; Hurricane, Omar A.

    2016-05-01

    The ablation material used during the National Ignition Campaign, a glow- discharge polymer (GDP), does not couple as efficiently as simulations indicated to the multiple- shock inducing radiation drive environment created by laser power profile [1]. We investigate the performance of two other ablators, boron carbide (B4C) and high-density carbon (HDC) and compare with GDP under the same hohlraum conditions. Ablation performance is determined through measurement of the shock speed produced in planar samples of the ablator subjected to the identical multiple-shock inducing radiation drive environments that are similar to a generic three-shock ignition drive. Simulations are in better agreement with the off-Hugoniot performance of B4C than either HDC or GDP.

  3. Insects feeding on cadavers as an alternative source of human genetic material

    Directory of Open Access Journals (Sweden)

    Rafał Skowronek

    2015-03-01

    Full Text Available In some criminal cases, the use of classical sources of human genetic material is difficult or even impossible. One solution may be the use of insects, especially blowfly larvae which feed on corpses. A recent review of case reports and experimental studies available in biomedical databases has shown that insects can be a valuable source of human mitochondrial and genomic deoxyribonucleic acid (DNA, allowing for an effective analysis of hypervariable region (HVR sequences and short tandem repeat (STR profiles, respectively. The optimal source of human DNA is the crop (a part of the gut of active third-instar blowfly larvae. Pupae and insect faeces can be also used in forensic genetic practice instead of the contents of the alimentary tract.

  4. Alternative approaches of SiC and related wide bandgap materials in light emitting and solar cell applications

    International Nuclear Information System (INIS)

    Materials for optoelectronics give a fascinating variety of issues to consider. Increasingly important are white light emitting diode (LED) and solar cell materials. Profound energy savings can be done by addressing new materials. White light emitting diodes are becoming common in our lighting scene. There is a great energy saving in the transition from the light bulb to white light emitting diodes via a transition of fluorescent light tubes. However, the white LEDs still suffer from a variety of challenges in order to be in our daily use. Therefore there is a great interest in alternative lighting solutions that could be part of our daily life. All materials create challenges in fabrication. Defects reduce the efficiency of optical transitions involved in the light emitting diode materials. The donor-acceptor co-doped SiC is a potential light converter for a novel monolithic all-semiconductor white LED. In spite of considerable research, the internal quantum efficiency is far less than theoretically predicted and is likely a fascinating scientific field for studying materials growth, defects and optical transitions. Still, efficient Si-based light source represents an ongoing research field in photonics that requires high efficiency at room temperature, wavelength tuning in a wide wavelength range, and easy integration in silicon photonic devices. In some of these devices, rare earth doped materials is considered as a potential way to provide luminescence spanning in a wide wavelength range. Divalent and trivalent oxidation states of Eu provide emitting centers in the visible region. In consideration, the use of Eu in photonics requires Eu doped thin films that are compatible with CMOS technology but for example faces material science issues like a low Eu solid solubility in silica. Therefore approaches aim to obtain efficient light emission from silicon oxycarbide which has a luminescence in the visible range and can be a host material for rare earth ions. The

  5. Report of material and equipment section`s activities at New York Shipbuilding Corporation during fabrication of AXC 167 1/2 starting May 18, 1951. Part 3

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, J.R.

    1954-05-26

    This report provides Part III through VI of the Material and Equipment Section`s activities at New York Shipbuilding Corporation. Fabrication, inspection, and testing of reactor components are detailed.

  6. Avaliação da partida e operação de filtros anaeróbios tendo bambu como material de recheio Start up evaluation and operation of anaerobic filters filled up with bamboo

    Directory of Open Access Journals (Sweden)

    Adriano Luiz Tonetti

    2011-03-01

    Full Text Available Neste trabalho, foram constituídos três filtros anaeróbios com volume de 500 L preenchidos com anéis de bambu, operando-os com tempo de detenção hidráulica de nove horas. O objetivo foi a determinação do período de partida sem o emprego de inóculo adaptado e a obtenção da eficiência no tratamento de esgoto doméstico, empregando-se um tempo de detenção hidráulica inferior às 12 horas sugeridas pela NBR 7229. Na avaliação do sistema, fez-se uso do carbono orgânico dissolvido, da demanda química de oxigênio, da demanda bioquímica de oxigênio, pH e alcalinidade, evidenciando quanto ao carbono orgânico dissolvido, a necessidade de 19 semanas para que se alcançasse o equilíbrio dinâmico nos reatores. Após esse período, a remoção atingiu 81,4 ± 6,4%. Os resultados demonstraram que o uso de um recheio alternativo nos filtros anaeróbios possibilitou uma eficiência similar a encontrada com materiais tradicionais, mesmo adotando-se um tempo de detenção hidráulica inferior ao indicado pela norma brasileira.In this paper, three anaerobic filters with 500 L volume were constructed and filled up with bamboo rings, operating with a nine hour hydraulic retention time. The aim was to determinate the start up period without using adapted sludge and reaching efficiency in a wastewater treatment, by deploying hydraulic detention time lower than the 12 hours suggested by the NBR 7229. In the system evaluation, it was used the dissolved organic carbon, chemical oxygen demand, biochemical oxygen demand, pH, and alkalinity, showing in terms of dissolved organic carbon, the need of 19 weeks to reach dynamic equilibrium in the reactors. After this period, the removal achieved 81.4 ± 6.4%. Results showed that using an alternative package in anaerobic filters made possible to have an efficacy similar to the one reached with traditional materials, even with the hydraulic detention time lower than the one suggested by the Brazilian law.

  7. Entrepreneur Training Program. Getting Started.

    Science.gov (United States)

    De Maria, Richard

    This student workbook on starting a small business is part of the entrepreneur training program at Ocean County (New Jersey) Vocational-Technical Schools. The workbook consists of 16 units containing goals and objectives, study questions, exercises, sample materials, and information sheets. Unit topics are as follows: being a small business owner;…

  8. Photothermal and thermoelastic microscopies: two alternative techniques for the non-destructive testing of materials

    International Nuclear Information System (INIS)

    This work aims at evaluating the possibility of application of photothermal and thermoelastic microscopies to the non-destructive testing of materials, such as niobium used in the fabrication of superconductive RF cavities. The theoretical results obtained in this study show the diagnostic potentialities of these techniques when applied to niobium sheets or directly to cavities. The microscopes that use an intensity modulated laser as excitation source have a lateral resolution comprised between 1 μm for fmod = 10 MHz and 30 to 50 μm for fmod = 10 kHz with a 1 μm diameter beam. These techniques allow the detection, localization, and sometimes the characterization, of subsurface and deep defects and inclusions. In far field regime the resolution of the method depends on the thermal diffusion depth. Thanks to the strong dependence between the laser induced stress and the thickness of the target, the photothermal and thermoelastic microscopes can be used also for the measurement of cavities thickness and internal profile. (J.S.)

  9. Review of material recovery from used electric and electronic equipment-alternative options for resource conservation.

    Science.gov (United States)

    Friege, Henning

    2012-09-01

    For waste from electric and electronic equipment, the WEEE Directive stipulates the separate collection of electric and electronic waste. As to new electric and electronic devices, the Restriction of Hazardous Substances (RoHS) Directive bans the use of certain chemicals dangerous for man and environment. From the implementation of the WEEE directive, many unsolved problems have been documented: poor collection success, emission of dangerous substances during collection and recycling, irretrievable loss of valuable metals among others. As to RoHS, data from the literature show a satisfying success. The problems identified in the process can be reduced to some basic dilemmas at the borders between waste management, product policy and chemical safety. The objectives of the WEEE Directive and the specific targets for use and recycling of appliances are not consistent. There is no focus on scarce resources. Extended producer responsibility is not sufficient to guarantee sustainable waste management. Waste management reaches its limits due to problems of implementation but also due to physical laws. A holistic approach is necessary looking at all branch points and sinks in the stream of used products and waste from electric and electronic equipment. This may be done with respect to the general rules for sustainable management of material streams covering the three dimensions of sustainable policy. The relationships between the players in the field of electric and electronic devices have to be taken into account. Most of the problems identified in the implementation process will not be solved by the current amendment of the WEEE Directive.

  10. Rice husk: an alternate and low cost material for treating chromium (VI) containing water

    International Nuclear Information System (INIS)

    This paper shows the ability of the native rice husk to remove ions of Cr (VI) in simulated water from tanneries in laboratory conditions. The influences of the variables pH, metal concentration, dosage and contact time on adsorption process was evaluated. It was found a removal more than 94% at pH value of 1, dosage of 3 g/L, concentration of 3 mg/L, at a speed of 127 rpm and at a time of 720 min. The results were evaluated with a 95% level of significance using the statistical tool ANOVA. The information regarding the balance process was fitted to the models of Freundlich, Langmuir, Dubinin-Raduskevich and Thempkin obtaining a better correlation with the Langmuir isotherm with an adsorption capacity of 1.25 mg/g at a pH value of 1. In order to prove the occurrence of structural changes on the adsorbent material, analysis was performed through the DRIFT technique (diffuse reflectance infrared spectroscopy) before and after the removal process and as well abromatological analyses to determine any variation in its composition.

  11. Electrohydrodynamic bubbling: an alternative route to fabricate porous structures of silk fibroin based materials.

    Science.gov (United States)

    Ekemen, Zeynep; Ahmad, Zeeshan; Stride, Eleanor; Kaplan, David; Edirisinghe, Mohan

    2013-05-13

    Conventional fabrication techniques and structures employed in the design of silk fibroin (SF) based porous materials provide only limited control over pore size and require several processing stages. In this study, it is shown that, by utilizing electrohydrodynamic bubbling, not only can new hollow spherical structures of SF be formed in a single step by means of bubbles, but the resulting bubbles can serve as pore generators when dehydrated. The bubble characteristics can be controlled through simple adjustments to the processing parameters. Bubbles with diameters in the range of 240-1000 μm were fabricated in controlled fashion. FT-IR characterization confirmed that the rate of air infused during processing enhanced β-sheet packing in SF at higher flow rates. Dynamic mechanical analysis also demonstrated a correlation between air flow rate and film tensile strength. Results indicate that electrohydrodynamically generated SF and their composite bubbles can be employed as new tools to generate porous structures in a controlled manner with a range of potential applications in biocoatings and tissue engineering scaffolds.

  12. Review of material recovery from used electric and electronic equipment-alternative options for resource conservation.

    Science.gov (United States)

    Friege, Henning

    2012-09-01

    For waste from electric and electronic equipment, the WEEE Directive stipulates the separate collection of electric and electronic waste. As to new electric and electronic devices, the Restriction of Hazardous Substances (RoHS) Directive bans the use of certain chemicals dangerous for man and environment. From the implementation of the WEEE directive, many unsolved problems have been documented: poor collection success, emission of dangerous substances during collection and recycling, irretrievable loss of valuable metals among others. As to RoHS, data from the literature show a satisfying success. The problems identified in the process can be reduced to some basic dilemmas at the borders between waste management, product policy and chemical safety. The objectives of the WEEE Directive and the specific targets for use and recycling of appliances are not consistent. There is no focus on scarce resources. Extended producer responsibility is not sufficient to guarantee sustainable waste management. Waste management reaches its limits due to problems of implementation but also due to physical laws. A holistic approach is necessary looking at all branch points and sinks in the stream of used products and waste from electric and electronic equipment. This may be done with respect to the general rules for sustainable management of material streams covering the three dimensions of sustainable policy. The relationships between the players in the field of electric and electronic devices have to be taken into account. Most of the problems identified in the implementation process will not be solved by the current amendment of the WEEE Directive. PMID:22993131

  13. Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement: Advancing Risk Analysis for Nanoscale Materials

    Energy Technology Data Exchange (ETDEWEB)

    Shatkin, J. A. [Vireo Advisors, Boston MA USA; Ong, Kimberly J. [Vireo Advisors, Boston MA USA; Beaudrie, Christian [Compass RM, Vancouver CA USA; Clippinger, Amy J. [PETA International Science Consortium Ltd, London UK; Hendren, Christine Ogilvie [Center for the Environmental Implications of NanoTechnology, Duke University, Durham NC USA; Haber, Lynne T. [TERA, Cincinnati OH USA; Hill, Myriam [Health Canada, Ottawa Canada; Holden, Patricia [UC Santa Barbara, Bren School of Environmental Science & Management, ERI, and UC CEIN, University of California, Santa Barbara CA USA; Kennedy, Alan J. [U.S. Army Engineer Research and Development Center, Environmental Laboratory, Vicksburg MS USA; Kim, Baram [Independent, Somerville MA USA; MacDonell, Margaret [Argonne National Laboratory, Environmental Science Division, Argonne IL USA; Powers, Christina M. [U.S. Environmental Protection Agency, Office of Air and Radiation, Office of Transportation and Air Quality, Ann Arbor MI USA; Sharma, Monita [PETA International Science Consortium Ltd, London UK; Sheremeta, Lorraine [Alberta Ingenuity Labs, Edmonton Alberta Canada; Stone, Vicki [John Muir Building Gait 1 Heriot-Watt University, Edinburgh Scotland UK; Sultan, Yasir [Environment Canada, Gatineau QC Canada; Turley, Audrey [ICF International, Durham NC USA; White, Ronald H. [RH White Consultants, Silver Spring MD USA

    2016-08-01

    The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article.

  14. A powerful methodological approach combining headspace solid phase microextraction, mass spectrometry and multivariate analysis for profiling the volatile metabolomic pattern of beer starting raw materials.

    Science.gov (United States)

    Gonçalves, João L; Figueira, José A; Rodrigues, Fátima P; Ornelas, Laura P; Branco, Ricardo N; Silva, Catarina L; Câmara, José S

    2014-10-01

    The volatile metabolomic patterns from different raw materials commonly used in beer production, namely barley, corn and hop-derived products - such as hop pellets, hop essential oil from Saaz variety and tetra-hydro isomerized hop extract (tetra hop), were established using a suitable analytical procedure based on dynamic headspace solid-phase microextraction (HS-SPME) followed by thermal desorption gas chromatography-quadrupole mass spectrometry detection (GC-qMS). Some SPME extraction parameters were optimized. The best results, in terms of maximum signal recorded and number of isolated metabolites, were obtained with a 50/30 μm DVB/CAR/PDMS coating fiber at 40 °C for 30 min. A set of 152 volatile metabolites comprising ketones (27), sesquiterpenes (26), monoterpenes (19), aliphatic esters (19), higher alcohols (15), aldehydes (11), furan compounds (11), aliphatic fatty acids (9), aliphatic hydrocarbons (8), sulphur compounds (5) and nitrogen compounds (2) were positively identified. Each raw material showed a specific volatile metabolomic profile. Monoterpenes in hop essential oil and corn, sesquiterpenes in hop pellets, ketones in tetra hop and aldehydes and sulphur compounds in barley were the predominant chemical families in the targeted beer raw materials. β-Myrcene was the most dominant volatile metabolite in hop essential oil, hop pellets and corn samples while, in barley, the predominant volatile metabolites were dimethyl sulphide and 3-methylbutanal and, in tetra hop, 6-methyl-2-pentanone and 4-methyl-2-pentanone. Principal component analysis (PCA) showed natural sample grouping among beer raw materials.

  15. Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement.

    Science.gov (United States)

    Shatkin, J A; Ong, Kimberly J; Beaudrie, Christian; Clippinger, Amy J; Hendren, Christine Ogilvie; Haber, Lynne T; Hill, Myriam; Holden, Patricia; Kennedy, Alan J; Kim, Baram; MacDonell, Margaret; Powers, Christina M; Sharma, Monita; Sheremeta, Lorraine; Stone, Vicki; Sultan, Yasir; Turley, Audrey; White, Ronald H

    2016-08-01

    The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article.

  16. Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement.

    Science.gov (United States)

    Shatkin, J A; Ong, Kimberly J; Beaudrie, Christian; Clippinger, Amy J; Hendren, Christine Ogilvie; Haber, Lynne T; Hill, Myriam; Holden, Patricia; Kennedy, Alan J; Kim, Baram; MacDonell, Margaret; Powers, Christina M; Sharma, Monita; Sheremeta, Lorraine; Stone, Vicki; Sultan, Yasir; Turley, Audrey; White, Ronald H

    2016-08-01

    The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article. PMID:27510619

  17. A powerful methodological approach combining headspace solid phase microextraction, mass spectrometry and multivariate analysis for profiling the volatile metabolomic pattern of beer starting raw materials.

    Science.gov (United States)

    Gonçalves, João L; Figueira, José A; Rodrigues, Fátima P; Ornelas, Laura P; Branco, Ricardo N; Silva, Catarina L; Câmara, José S

    2014-10-01

    The volatile metabolomic patterns from different raw materials commonly used in beer production, namely barley, corn and hop-derived products - such as hop pellets, hop essential oil from Saaz variety and tetra-hydro isomerized hop extract (tetra hop), were established using a suitable analytical procedure based on dynamic headspace solid-phase microextraction (HS-SPME) followed by thermal desorption gas chromatography-quadrupole mass spectrometry detection (GC-qMS). Some SPME extraction parameters were optimized. The best results, in terms of maximum signal recorded and number of isolated metabolites, were obtained with a 50/30 μm DVB/CAR/PDMS coating fiber at 40 °C for 30 min. A set of 152 volatile metabolites comprising ketones (27), sesquiterpenes (26), monoterpenes (19), aliphatic esters (19), higher alcohols (15), aldehydes (11), furan compounds (11), aliphatic fatty acids (9), aliphatic hydrocarbons (8), sulphur compounds (5) and nitrogen compounds (2) were positively identified. Each raw material showed a specific volatile metabolomic profile. Monoterpenes in hop essential oil and corn, sesquiterpenes in hop pellets, ketones in tetra hop and aldehydes and sulphur compounds in barley were the predominant chemical families in the targeted beer raw materials. β-Myrcene was the most dominant volatile metabolite in hop essential oil, hop pellets and corn samples while, in barley, the predominant volatile metabolites were dimethyl sulphide and 3-methylbutanal and, in tetra hop, 6-methyl-2-pentanone and 4-methyl-2-pentanone. Principal component analysis (PCA) showed natural sample grouping among beer raw materials. PMID:24799238

  18. Phosphogypsum as an alternative building material: preliminary modeling and simulation of radon-222 exhalation from blocks and indoor accumulation

    International Nuclear Information System (INIS)

    Phosphogypsum is a by-product from the phosphate fertilizer industry and its large-scale utilization as an alternative construction material copes with radiological issues related to radon-222. Zero-order models for radon-222 exhalation from phosphogypsum building blocks and its time-varying accumulation in closed domains (e.g. indoor accumulation) presume homogeneous distribution of radon-222 throughout the enclosure. Having in mind radiological protection design, exhalation characterization of a block sample is a valuable parameter for the corresponding building performance simulation and it can be accomplished by placing a test block inside a test chamber together with a suitable nuclear detector (their relative positioning depends on the chamber geometry). As breakdown of the uniform concentration hypothesis is likely to occur, this preliminary work numerically investigates such model oversimplification. Along with emanation and decay processes, the present mathematical model assumes time-dependent two-dimensional diffusion-dominant mass transfer in a domain containing a sample of porous material, namely the phosphogypsum block of finite thickness. Conversely, as the test chamber is quite small and air-tight closed, convective mass transfer is neglected. Numerically simulated results have confirmed that a non-uniform radon-222 distribution takes place, which can obviously influence the position of the nuclear detector (or its primary element), thus affecting its readings. (author)

  19. Start with Science

    Science.gov (United States)

    Erickson, Susan

    2012-01-01

    The author has found over her 13 years of teaching that starting off the school year with a science investigation has been a great method to learn about her students, to engage them about science before the school year even starts, and to build a foundation for a year of engaging science experiences. This article describes four such activities…

  20. Lean start-up

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2016-01-01

    The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

  1. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept. A preliminary Ti-clay interaction study

    International Nuclear Information System (INIS)

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (2 which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980s (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. 2 or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO2 units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out to shed more light on Ti-clay interaction processes and on the Ti species resulting from these interactions. Purified MX-80 bentonite was mixed with metallic Ti nano powder and foil at different pH and temperature conditions. After several months, solid and solute samples from the first set of tests were analyzed by wet chemistry and quantitative X-ray fluorescence analysis. The chemical speciation of Ti was analyzed with XAS. In addition to reacted samples, a number of reference and starting materials (e.g. MX-80, Rokle bentonite, Opalinus Clay, Illite du Puy) were characterized by XRF

  2. Processing of Ceramic Based Nanocomposite Using α-Al2O3 Powder and FeCl2 Solution as Starting Materials

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Alumina-iron nanocomposite powders were prepared by a two-step process. In the first step, α-Al2O3-FeCl2 powder mixture was formed by mixing α-Al2O3 powders with FeCl2 solution followed by drying. In the second step, the FeCl2 in the dry power mixture was selectively reduced to iron particles. A reduction temperature of 750℃ for 15 min in dry H2 was chosen based on the thermodynamic calculations. The concentration of iron in FeCl2 solution was calculated to be 20 vol. pct in the final composite. Two techniques were used to produce composite bulk materials. The Al2O3 nanocomposite powders were divided to two batches. The first batch of the produced mixture was hot pressed at 1400℃ and 27 MPa for 30 min in a graphite die. To study the effect of oxygen on the Al2O3/Fe interface bonding and mechanical properties of the composite,the second batch was heat treated in air at 700℃ for 20 min to partially oxidize the iron particles before hot pressing. Characterization of the composites was undertaken by conventional density measurements, X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe micro analysis (EPMA). The suggested processing route (mixing, reduction and hot pressing)produces ceramic-metal nanocomposite much tougher than the pure Al2O3. The fracture strength of the produced Al2O3/Fe nanocomposite is nearly twice that of the pure Al2O3. The presence of spinel phase,FeAl2O4, as thick layer around the Fe particles in the Al2O3 matrix has a detrimental effect on interfacial bonding between Fe and Al2O3 and the fracture properties of the composite.

  3. Importance of Fuel Cell Tests for Stability Assessment—Suitability of Titanium Diboride as an Alternative Support Material

    Directory of Open Access Journals (Sweden)

    Christina Roth

    2014-06-01

    Full Text Available Carbon corrosion is a severe issue limiting the long-term stability of carbon-supported catalysts, in particular in the highly dynamic conditions of automotive applications. (Doped oxides have been discussed as suitable alternatives to replace carbon, but often suffer from poor electron conductivity. That is why non-oxide ceramics, such as tungsten carbide and titanium nitride, have been discussed recently. Titanium diboride has also been proposed, due to its promising activity and stability in an aqueous electrochemical cell. In this work, Pt nanoparticles were deposited onto μm-sized TiB2 particles with improved grain size, manufactured into porous gas diffusion electrodes and tested in a realistic polymer electrolyte membrane (PEM fuel cell environment. In contrast to the model studies in an aqueous electrochemical cell, in the presence of oxygen and high potentials at the cathode side of a real fuel cell, TiB2 becomes rapidly oxidized as indicated by intensely colored regions in the membrane-electrode assembly (MEA. Moreover, already the electrode manufacturing process led to the formation of titanium oxides, as shown by X-ray diffraction measurements. This demonstrates that Cyclic Voltammetry (CV measurements in an aqueous electrochemical cell are not sufficient to prove stability of novel materials for fuel cell applications.

  4. Head Start Impact Study

    Data.gov (United States)

    U.S. Department of Health & Human Services — Nationally representative, longitudinal information from an evaluation where children were randomly assigned to Head Start or community services as usual;direct...

  5. Early Head Start Evaluation

    Data.gov (United States)

    U.S. Department of Health & Human Services — Longitudinal information from an evaluation where children were randomly assigned to Early Head Start or community services as usual;direct assessments and...

  6. FEMA DFIRM Station Start

    Data.gov (United States)

    Minnesota Department of Natural Resources — This table contains information about station starting locations. These locations indicate the reference point that was used as the origin for distance measurements...

  7. Getting started with Unity

    CERN Document Server

    Felicia, Patrick

    2013-01-01

    Getting Started with Unity is written in an easy-to-follow tutorial format.""Getting Started with Unity"" is for[ 3D game developers[/color] who would like to learn how to use Unity3D and become familiar with its core features. This book is also suitable for intermediate users who would like to improve their skills. No prior knowledge of Unity3D is required.

  8. START: Overcoming Remaining Challenges

    Directory of Open Access Journals (Sweden)

    Elizabeth Zolotukhina

    2009-01-01

    Full Text Available During the administrations of Presidents George W. Bush and VladimirPutin, the governments of Russia and the United States could not agreeon how to codify their balance of strategic offensive nuclear forces after the existing Strategic Arms Reductions Treaty (START expired onDecember 5, 2009.1 The United States and Russia are currently engagedin negotiations to replace START with a new treaty before the end of this year.

  9. Improved neutron radiation hardness for Si detectors: Application of low resistivity starting material and/or manipulation of N{sub eff} by selective filling of radiation-induced traps at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Dezillie, B.; Li, Z. [Brookhaven National Lab., Upton, NY (United States); Eremin, V. [Academy of Science of Russia (Russian Federation). A.F. Ioffe Physico-Technical Inst.; Bruzzi, M.; Pirollo, S. [Dipt. di Energetica, Firenze (Italy); Pandey, S.U. [Wayne State Univ., Detroit, MI (United States); Li, C.J. [Chinese Academy of Science, Beijing (China). Inst. of Semiconductors

    1999-06-01

    Radiation-induced electrical changes in both space charge region (SCR) of Si detectors and bulk material (BM) have been studied for samples of diodes and resistors made on Si materials with different initial resistivities. The space charge sign inversion fluence ({Phi}{sub inv}) has been found to increase linearly with the initial doping concentration (the reciprocal of the resistivity), which gives improved radiation hardness to Si detectors fabricated from low resistivity material. The resistivity of the BM, on the other hand, has been observed to increase with the neutron fluence and approach a saturation value in the order of hundreds k{Omega}cm at high fluences, independent of the initial resistivity and material type. However, the fluence ({Phi}{sub s}), at which the resistivity saturation starts, increases with the initial doping concentrations and the value of {Phi}{sub s} is in the same order of that of {Phi}{sub inv} for all resistivity samples. Improved radiation hardness can also be achieved by the manipulation of the space charge concentration (N{sub eff}) in SCR, by selective filling and/or freezing at cryogenic temperatures the charge state of radiation-induced traps, to values that will give a much smaller full depletion voltage. Models have been proposed to explain the experimental data.

  10. Recycling biosolids and lake-dredged materials to pasture-based animal agriculture: Alternative nutrient sources for forage productivity and sustainability.

    Science.gov (United States)

    The prohibition of dumping dredged and domestic sewage sludge (DSS) materials in streams and oceans, diminishing land fill space, skyrocketing landfill costs, and concerns over air pollution from incineration of wastes have contributed to a strong public interest in finding alternative, environmenta...

  11. How Do I Start?

    Science.gov (United States)

    ... desires, and life style. USING COMPLEMENTARY AND ALTERNATIVE THERAPIES Some people believe they have stayed healthier because they use traditional healing practices, massage, acupuncture, herbs, or other therapies. Fact ...

  12. Amorphous carbon nitride as an alternative electrode material in electroanalysis: simultaneous determination of dopamine and ascorbic acid.

    Science.gov (United States)

    Medeiros, Roberta A; Matos, Roberto; Benchikh, Abdelkader; Saidani, Boualem; Debiemme-Chouvy, Catherine; Deslouis, Claude; Rocha-Filho, Romeu C; Fatibello-Filho, Orlando

    2013-10-01

    Boron-doped diamond (BDD) films are excellent electrode materials, whose electrochemical activity for some analytes can be tuned by controlling their surface termination, most commonly either to predominantly hydrogen or oxygen. This tuning can be accomplished by e.g. suitable cathodic or anodic electrochemical pretreatments. Recently, it has been shown that amorphous carbon nitride (a-CNx) films may present electrochemical characteristics similar to those of BDD, including the influence of surface termination on their electrochemical activity toward some analytes. In this work, we report for the first time a complete electroanalytical method using an a-CNx electrode. Thus, an a-CNx film deposited on a stainless steel foil by DC magnetron sputtering is proposed as an alternative electrode for the simultaneous determination of dopamine (DA) and ascorbic acid (AA) in synthetic biological samples by square-wave voltammetry. The obtained results are compared with those attained using a BDD electrode. For both electrodes, a same anodic pretreatment in 0.1 mol L(-1) KOH was necessary to attain an adequate and equivalent separation of the DA and AA oxidation potential peaks of about 330 mV. The detection limits obtained for the simultaneous determination of these analytes using the a-CNx electrode were 0.0656 μmol L(-1) for DA and 1.05 μmol L(-1) for AA, whereas with the BDD electrode these values were 0.283 μmol L(-1) and 0.968 μmol L(-1), respectively. Furthermore, the results obtained in the analysis of the analytes in synthetic biological samples were satisfactory, attesting the potential application of the a-CNx electrode in electroanalysis.

  13. Amorphous carbon nitride as an alternative electrode material in electroanalysis: Simultaneous determination of dopamine and ascorbic acid

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, Roberta A., E-mail: roantigo@hotmail.com [Departamento de Química, Universidade Federal de São Carlos, C.P. 676, 13560-970 São Carlos, SP (Brazil); Matos, Roberto [Departamento de Química, Universidade Federal de São Carlos, C.P. 676, 13560-970 São Carlos, SP (Brazil); Benchikh, Abdelkader [LECVE, Faculté de la Technologie, Département de Génie des Procédés, Université Abderrahmane MIRA, Béjaïa (Algeria); LISE UPR 15 du CNRS, Université Pierre et Marie Curie, 4, Place Jussieu, 75005 Paris (France); Saidani, Boualem [LECVE, Faculté de la Technologie, Département de Génie des Procédés, Université Abderrahmane MIRA, Béjaïa (Algeria); Debiemme-Chouvy, Catherine [LISE UPR 15 du CNRS, Université Pierre et Marie Curie, 4, Place Jussieu, 75005 Paris (France); Deslouis, Claude, E-mail: claude.deslouis@upmc.fr [LISE UPR 15 du CNRS, Université Pierre et Marie Curie, 4, Place Jussieu, 75005 Paris (France); Rocha-Filho, Romeu C.; Fatibello-Filho, Orlando [Departamento de Química, Universidade Federal de São Carlos, C.P. 676, 13560-970 São Carlos, SP (Brazil)

    2013-10-03

    Graphical abstract: -- Highlights: •a-CN{sub x} films are a new class of electrodic carbon materials that present several properties similar to those of BDD films. •a-CN{sub x} and BDD were used as working electrodes for simultaneous determination of DA and AA. •Electrochemical pretreatments on a-CN{sub x} or BDD modified the nature of the surface terminations. •An anodic pretreatment in 0.1 mol L{sup −1} KOH was necessary to attain an adequate separation of the DA and AA oxidation potential peaks. •For the first time in the literature, the use of an a-CN{sub x} electrode in a complete electroanalytical procedure is reported. -- Abstract: Boron-doped diamond (BDD) films are excellent electrode materials, whose electrochemical activity for some analytes can be tuned by controlling their surface termination, most commonly either to predominantly hydrogen or oxygen. This tuning can be accomplished by e.g. suitable cathodic or anodic electrochemical pretreatments. Recently, it has been shown that amorphous carbon nitride (a-CN{sub x}) films may present electrochemical characteristics similar to those of BDD, including the influence of surface termination on their electrochemical activity toward some analytes. In this work, we report for the first time a complete electroanalytical method using an a-CN{sub x} electrode. Thus, an a-CN{sub x} film deposited on a stainless steel foil by DC magnetron sputtering is proposed as an alternative electrode for the simultaneous determination of dopamine (DA) and ascorbic acid (AA) in synthetic biological samples by square-wave voltammetry. The obtained results are compared with those attained using a BDD electrode. For both electrodes, a same anodic pretreatment in 0.1 mol L{sup −1} KOH was necessary to attain an adequate and equivalent separation of the DA and AA oxidation potential peaks of about 330 mV. The detection limits obtained for the simultaneous determination of these analytes using the a-CN{sub x

  14. Start-Up Capital

    NARCIS (Netherlands)

    I. Verheul (Ingrid); A.R. Thurik (Roy)

    2000-01-01

    textabstractFemale and male entrepreneurs differ in the way they finance their businesses. This can be attributed to the type of business and the type of management and experience (indirect effect). Female start-ups may also experience other barriers based upon discriminatory effects (direct effect)

  15. Getting started with Go

    CERN Document Server

    CERN. Geneva

    2015-01-01

    No, not the Chinese boardgame, the programming language that ironically Google made difficult to google for. You may have heard of Golang, and are wondering whether you should learn it. The answer is that of course you should, and this talk should explain why and point you at the best resources to get started.

  16. Stumbling before the start

    NARCIS (Netherlands)

    Lex Herweijer

    2008-01-01

    Original title: Gestruikeld voor de start. Reducing school dropout rates is high on the education policy agenda in the Netherlands. Too many young people are leaving school without an initial qualification, and in response the government has set itself the target of halving the number of premature

  17. Getting started with UDOO

    CERN Document Server

    Palazzetti, Emanuele

    2015-01-01

    If you are an Android developer who wants to learn how to use UDOO to build Android applications that are capable of interacting with their surrounding environment, then this book is ideal for you. Learning UDOO is the next great step to start building your first real-world prototypes powered by the Android operating system.

  18. ATLAS starts moving in

    CERN Multimedia

    2004-01-01

    The first large active detector component was lowered into the ATLAS cavern on 1 March. It consisted of the 8 modules forming the lower part of the central barrel of the tile hadronic calorimeter. The work of assembling the barrel, which comprises 64 modules, started the following day.

  19. A New Start

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Goodwill to the Islamic world and willingness to mend ties highlight Barack Obama’s new Middle East policy u.S. President Barack Obama started to implement his new Middle East policy soon after he assumed office. He paid a

  20. 23 CFR Appendix to Subpart F of... - Alternate Method of Determining the Color of Retroreflective Sign Materials and Pavement Marking...

    Science.gov (United States)

    2010-04-01

    ... Retroreflective Sign Materials and Pavement Marking Materials Appendix to Subpart F of Part 655 Highways FEDERAL... Pavement Marking Materials 1. Although the FHWA Color Tolerance Charts depreciate the use of... for Retroreflective Pavement Marking Material With CIE 2° Standard Observer and 45/0 (0/45)...

  1. Getting Started with Hibernate 3

    CERN Document Server

    Elliott, James

    2008-01-01

    Hibernate has clearly arrived. Are you ready to benefit from its simple way of working with relational databases as Java objects? This PDF updates the introductory material from the award-winning Hibernate: A Developer's Notebook to teach you how to jump right in and get productive with the current release of Hibernate. You'll be walked through the ins and outs of setting up Hibernate and some related tools that make it easier to use--and that may give you new ideas about how to store information in your Java programs. In short, this PDF gives you exactly the information you need to start u

  2. Getting started with Hazelcast

    CERN Document Server

    Johns, Mat

    2013-01-01

    Written as a step-by-step guide, Getting Started with Hazelcast will teach you all you need to know to make your application data scalable.This book is a great introduction for Java developers, software architects, or developers looking to enable scalable and agile data within their applications. You should have programming knowledge of Java and a general familiarity with concepts like data caching and clustering.

  3. The Healthy Start project

    DEFF Research Database (Denmark)

    Olsen, Nanna J; Buch-Andersen, Tine; Händel, Mina N;

    2012-01-01

    ABSTRACT: BACKGROUND: Research shows that obesity prevention has to start early. Targeting interventions towards subgroups of individuals who are predisposed, but yet normal weight, may prove more effective in preventing overweight than interventions towards unselected normal weight subsets...... is effective in preventing excessive weight gain, it will provide valuable information on new determinants of obesity that should be considered in future interventions, and on new strategies to prevent development of overweight and obesity at an early age. Trial Registration Number: NCT01583335....

  4. Start-up procedure

    International Nuclear Information System (INIS)

    The start-up procedure will be shown on a pressurized water reactor, although most of the activities will occur similarly in other reactor types. The commissioning time can be divided into 5 sections, the phases A to E together lasting 26 months. Subsequently there are a test run of one month and the handling-over of the plant to the operator. A survey of the commissioning sections with several important main events is shown. (orig./TK)

  5. Getting started with JUCE

    CERN Document Server

    Robinson, Martin

    2013-01-01

    his book is a fast-paced, practical guide full of step-by-step examples which are easy to follow and implement.This book is for programmers with a basic grasp of C++. The examples start at a basic level, making few assumptions beyond fundamental C++ concepts. Those without any experience with C++ should be able to follow and construct the examples, although you may need further support to understand the fundamental concepts.

  6. Getting started with Simulink

    CERN Document Server

    Zamboni, Luca

    2013-01-01

    This practical and easy-to-understand learning tutorial is one big exciting exercise for students and engineers that are always short on their schedules and want to regain some lost time with the help of Simulink.This book is aimed at students and engineers who need a quick start with Simulink. Though it's not required in order to understand how Simulink works, knowledge of physics will help the reader to understand the exercises described.

  7. Alternative invitro propagation: use of sugarcane bagasse as a low cost support material during rooting stage of strawberry cv. Dover

    Directory of Open Access Journals (Sweden)

    Radjiskumar Mohan

    2005-06-01

    Full Text Available The purpose of this work was to reduce the cost and improve the quality of the plant material during the micropropagation process in tissue culture. Partially improvement in the rooting process, coupled with cost reduction was obtained during the invitro rooting by the use of a natural support based on sugarcane bagasse as a substitute for the traditionally used agar gelled medium. The tests were conducted with micro-cuttings of strawberry cv. Dover using a medium composed of half strength MS medium (1962, 3% sucrose and 0.05 BAP mg.l-1. The roots number, shoots number, length, and the height of aerial part of 8 independent plants were recorded after 10, 20, 30, and 40 days of culture. Also, an acclimatization tests were realized of the rooted shoots from both the media. A comparison with agar-grown micro-cuttings showed that the sugarcane bagasse yielded better results (14, 40, 15 and 12 respectively. Acclimatization tests were 83% from the agar gelled medium against 100% from the bagasse medium. As the Paraná State, Brazil, possess in great number of the sugarcane bagasse; this can feed the alternative technology invented on the area of micropropagation techniques.Para a obtenção de mudas (material vegetal sadias de espécies de café em maior quantidade e em tempo reduzido, utiliza-se a técnica de micropropagação vegetal. Essa técnica é realizada em diferentes etapas, desde o isolamento até o transporte para extra vitro. Cada etapa demanda tempo e gera custos onerosos, sendo ainda necessário otimizar o rendimento. Para melhorar o processo total é essencial que cada etapa colabore com o máximo de rendimento, no menor tempo e com o menor custo possível. Este trabalho teve como focos as etapas de enraizamento e de aclimatização com as seguintes mudanças previstas: o enraizamento destes micro-tecidos propagados em meio de cultura modificado (substituição do meio semi-sólido por bagaço de mandioca e/ou bagaço de cana

  8. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept. A preliminary Ti-clay interaction study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, Paul (Gruner Ltd (Switzerland)); Grolimund, Daniel (Paul Scherrer Institute (Switzerland)); Kumpulainen, Sirpa; Kiviranta, Leena (BandTech Oy (Finland)); Brendle, Jocelyne (University of Mulhouse (France)); Snellman, Margit (Saanio and Riekkola Oy (Finland))

    2010-12-15

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (< 1 nm/a) over a large range of pH and Eh conditions. The corrosion behaviour is governed by the low solubility of tetravalent TiO{sub 2} which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980s (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. <1 nm/a. So far, no work on reaction products from this interaction process has been carried out. Even the speciation of Ti in natural clays is uncertain. In principle, four possible reaction products resulting from Ti-clay interactions are possible: (i) Ti sorbed to the clay surface via cation exchange or specific adsorption, (ii) Ti incorporated in the octahedral or tetrahedral clay structure, (iii) Ti precipitated as separate TiO{sub 2} or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO{sub 2} units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out

  9. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept: A preliminary Ti-clay interaction study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, P. [Gruner Ltd, Basel (Switzerland); Grolimund, D. [Paul Scherrer Inst., Villigen (Switzerland); Kumpulainen, S.; Kiviranta, L. [B and Tech Oy, Helsinki (Finland); Brendle, J. [Mulhouse Univ. (France); Snellman, M. [Saanio and Riekkola Oy, Helsinki (Finland)

    2011-12-15

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (< 1 nm/a) over a large range of pH and Eh conditions. The corrosion behaviour is governed by the low solubility of tetravalent TiO{sub 2} which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980ies (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. 1 nm/a. So far, no work on reaction products from this interaction process has been carried out. Even the speciation of Ti in natural clays is uncertain. In principle, four possible reaction products resulting from Ti-clay interactions are possible: (i) Ti sorbed to the clay surface via cation exchange or specific adsorption, (ii) Ti incorporated in the octahedral or tetrahedral clay structure, (iii) Ti precipitated as separate TiO{sub 2} or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO{sub 2} units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out

  10. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept: A preliminary Ti-clay interaction study

    International Nuclear Information System (INIS)

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (2 which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980ies (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. 1 nm/a. So far, no work on reaction products from this interaction process has been carried out. Even the speciation of Ti in natural clays is uncertain. In principle, four possible reaction products resulting from Ti-clay interactions are possible: (i) Ti sorbed to the clay surface via cation exchange or specific adsorption, (ii) Ti incorporated in the octahedral or tetrahedral clay structure, (iii) Ti precipitated as separate TiO2 or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO2 units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out to shed more light on Ticlay interaction processes and on the Ti species resulting from these interactions. Purified MX-80 bentonite was mixed with metallic

  11. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept. A preliminary Ti-clay interaction study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, Paul (Gruner Ltd (Switzerland)); Grolimund, Daniel (Paul Scherrer Institute (Switzerland)); Kumpulainen, Sirpa; Kiviranta, Leena (BandTech Oy (Finland)); Brendle, Jocelyne (University of Mulhouse (France)); Snellman, Margit (Saanio and Riekkola Oy (Finland))

    2010-12-15

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (< 1 nm/a) over a large range of pH and Eh conditions. The corrosion behaviour is governed by the low solubility of tetravalent TiO{sub 2} which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980s (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. <1 nm/a. So far, no work on reaction products from this interaction process has been carried out. Even the speciation of Ti in natural clays is uncertain. In principle, four possible reaction products resulting from Ti-clay interactions are possible: (i) Ti sorbed to the clay surface via cation exchange or specific adsorption, (ii) Ti incorporated in the octahedral or tetrahedral clay structure, (iii) Ti precipitated as separate TiO{sub 2} or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO{sub 2} units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out

  12. Titanium alloys as alternative material for the supercontainer shell in the KBS-3H concept: A preliminary Ti-clay interaction study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, P. [Gruner Ltd, Basel (Switzerland); Grolimund, D. [Paul Scherrer Inst., Villigen (Switzerland); Kumpulainen, S.; Kiviranta, L. [B and Tech Oy, Helsinki (Finland); Brendle, J. [Mulhouse Univ. (France); Snellman, M. [Saanio and Riekkola Oy, Helsinki (Finland)

    2011-12-15

    Ti alloys have been proposed as alternative materials to steel for the supercontainer shell surrounding the bentonite buffer in the KBS-3H disposal concept. Ti-based materials display high strength and are known to behave chemically inert under a variety of conditions. This preliminary study addresses the suitability of titanium as supercontainer material with regard to the performance of the clay buffer. Thus, possible titanium-bentonite interactions which may adversely affect the buffer's safety functions are evaluated by means of a literature and a preliminary experimental assessment. Titanium metals display very low corrosion rates (< 1 nm/a) over a large range of pH and Eh conditions. The corrosion behaviour is governed by the low solubility of tetravalent TiO{sub 2} which forms a passive surface corrosion layer under both oxic and reducing conditions. The interactions between titanium and clay have been barely studied so far. Preliminary long-term data obtained by Prof. Olefjord and co-workers from Chalmers (S) in the 1980ies (as part of SKB's canister program) suggests similar corrosion rates in compacted bentonite compared to those measured in water, i.e. 1 nm/a. So far, no work on reaction products from this interaction process has been carried out. Even the speciation of Ti in natural clays is uncertain. In principle, four possible reaction products resulting from Ti-clay interactions are possible: (i) Ti sorbed to the clay surface via cation exchange or specific adsorption, (ii) Ti incorporated in the octahedral or tetrahedral clay structure, (iii) Ti precipitated as separate TiO{sub 2} or mixed (Fe, Ti) oxide, (iv) Ti precipitated as separate silicate phase and (v) polymerized as cross-linked TiO{sub 2} units in the interlayer (Ti pillared clay). The latter two transformation products would have the strongest impact on the buffer, but are improbable on the basis of current knowledge. A preliminary batch-type investigation has been carried out

  13. Getting Started with Processing

    CERN Document Server

    Reas, Casey

    2010-01-01

    Learn computer programming the easy way with Processing, a simple language that lets you use code to create drawings, animation, and interactive graphics. Programming courses usually start with theory, but this book lets you jump right into creative and fun projects. It's ideal for anyone who wants to learn basic programming, and serves as a simple introduction to graphics for people with some programming skills. Written by the founders of Processing, this book takes you through the learning process one step at a time to help you grasp core programming concepts. You'll learn how to sketch wi

  14. Getting started with Arduino

    CERN Document Server

    Banzi, Massimo

    2011-01-01

    Arduino is the open-source electronics prototyping platform that's taken the design and hobbyist world by storm. This thorough introduction, updated for Arduino 1.0, gives you lots of ideas for projects and helps you work with them right away. From getting organized to putting the final touches on your prototype, all the information you need is here! Inside, you'll learn about: Interaction design and physical computingThe Arduino hardware and software development environmentBasics of electricity and electronicsPrototyping on a solderless breadboardDrawing a schematic diagram Getting started

  15. Getting Started with Netduino

    CERN Document Server

    Walker, Chris

    2012-01-01

    Start building electronics projects with Netduino, the popular open source hardware platform that's captured the imagination of makers and hobbyists worldwide. This easy-to-follow book provides the step-by-step guidance you need to experiment with Netduino and the .NET Micro Framework. Through a set of simple projects, you'll learn how to create electronic gadgets-including networked devices that communicate over TCP/IP. Along the way, hobbyists will pick up the basics of .NET programming, and programmers will discover how to work with electronics and microcontrollers. Follow the projects in

  16. Getting Started with Roo

    CERN Document Server

    Long, Josh

    2011-01-01

    Spring Roo goes a step beyond the Spring Framework by bringing true Rapid Application Development to Java-just as Grails has done with Groovy. This concise introduction shows you how to build applications with Roo, using the framework's shell as an intelligent and timesaving code-completion tool. It's an ideal RAD tool because Roo does much of the tedious code maintenance. You'll get started by building a simple customer relationship management application, complete with step-by-step instructions and code examples. Learn how to control any part of the application with Roo's opt-in feature, w

  17. Studies on teff (Eragrostis tef) malt as alternative raw material for lactic acid fermented gluten-free beverages

    OpenAIRE

    Gebremariam, Mekonnen Melaku

    2015-01-01

    This project was designed to study influences of kilning conditions on quality attributes of teff malt, and thermal stabilities of its amylolytic enzymes, and develop processing conditions to utilize it as alternative raw material for gluten-free beverage. To this end, optimal kilning and mashing conditions were developed, and finally, an optimal fermentation condition yielding a beverage with sufficiently low pH to suppress growth of food spoilage microorganisms and acceptable sensory qualit...

  18. Nutriendo la Promesa: Materiales Para la Aplicacion de las Normas de Ejecucion del Programa Head Start. Guia Para la Utilizacion de los Materiales [y] Transparencias (Nurturing the Promise: Set of Training Materials on the Head Start Program Performance Standards. User's Guide [and] Set of Transparencies).

    Science.gov (United States)

    Educational Services, Inc., Washington, DC.

    Since 1975, the Head Start Program Performance Standards have defined the services that local programs are required to provide to enrolled children and families. With revisions effective in 1998, the Program Performance Standards translate the Head Start vision into quality practices implemented at the local level. This document is comprised of a…

  19. Collecting Forever or Just-in-Time: An Alternative to Enhance Customers' Access to Chinese Language Materials through Resource Sharing

    Science.gov (United States)

    Situ, Ping; Voyles, Jeanne

    2008-01-01

    Libraries need to weigh the benefits, usage, and cost-effectiveness of owning collections against seeking alternatives to deliver the information needed by customers. The University of Arizona Library investigated different approaches for meeting the research needs of East Asian Studies faculty and students under great pressure of physical space…

  20. Starting at the Top.

    Science.gov (United States)

    Golden, Brian

    2001-01-01

    Explains why the ceiling systems that schools choose are as important to creating a constructive learning environment as any other finishing material and furnishing. Some effective wall system strategies are also highlighted. (GR)

  1. Missouri: Early Head Start Initiative

    Science.gov (United States)

    Center for Law and Social Policy, Inc. (CLASP), 2012

    2012-01-01

    Missouri's Early Head Start/Child Care Partnership Project expands access to Early Head Start (EHS) services for children birth to age 3 by developing partnerships between federal Head Start, EHS contractors, and child care providers. Head Start and EHS contractors that participate in the initiative provide services through community child care…

  2. In vivo degradation in modern orthopaedic UHMWPE bearings and structural characterization of a novel alternative UHMWPE material

    Science.gov (United States)

    Reinitz, Steven D.

    Ultra-high molecular weight polyethylene (UHMWPE) remains the most common bearing material for total joint arthroplasty. Advances in radiation cross-linking and other post-consolidation treatments have led to a rapid differentiation of polyethylene products on the market, with more than twenty unique materials currently being sold by the five largest orthopaedic manufacturers alone. Through oxidation, cross-link density, and free radical measurements, this work demonstrates for the first time that in vivo material degradation is occurring in cross-linked UHMWPE materials. Based on the rate of the reaction in certain materials, it is concluded that oxidative degradation may compromise the mechanical properties of the bearings in as few as ten years, potentially leading to early clinical failure of the devices. Using the knowledge gained from this work as well as previously published observations about UHMWPE oxidation, a two-mechanism model of oxidation is proposed that offers an explanation for the observed in vivo changes. From this model it is concluded that oxidative degradation is in part the result of in vivo chemical species. The two-mechanism model of oxidation suggests that different processing techniques for UHMWPE may reduce the risk of oxidative degradation. It is concluded that by avoiding any radiation cross-linking step, Equal Channel Angular Processing (ECAP) can produce UHMWPE materials with a reduced risk for in vivo oxidation while at the same time offering superior mechanical properties compared to commercially available UHMWPE materials, as well as similar wear behavior. Using dynamic mechanical analysis, the entanglement density in ECAP materials is quantified, and is related back to the ECAP processing parameters. The relationship between entanglement density and resultant material properties is established. The results will allow informed processing parameter selection for producing optimized materials for orthopaedics and other applications.

  3. THE USE OF COMPOSIT MATERIALS ALTERNATIVE FIBERGLASS (COCO FIBERS & RAGS) ON FIBERGLASS SHIP IN TRADITIONAL SHIPYARDS BENGKALIS REGENCY

    OpenAIRE

    Romadhoni Oni

    2015-01-01

    The limitations of the current wood raw material nowadays is  a threat to the traditional shipbuilding business. Besides the material is expensive, it is also about the difficulty in bringing the major raw materials, fiberglass, suchas wood fiber MAT and WR ( Woven Roofing). There is plan issues to ban on the use of the fiber within a certain period  that accelerate the research in making the solution to be environment- free fiber. By doing the mechanical testing of coco fibre and rags, then ...

  4. LEP dismantling starts

    CERN Multimedia

    2000-01-01

    Since the end of November, various teams have been getting stuck into dismantling the LEP accelerator and its four experiments. After making the installations safe, the dismantling and removal of 40,000 tonnes of equipment is underway. Down in the tunnel, it is a solemn moment. It is 10 o'clock on 13 December and Daniel Regin, one of those heading the dismantling work, moves in on a magnet, armed with a hydraulic machine. Surrounded by teams gathered there for a course in dismantling, he makes the first cut into LEP. The great deconstruction has begun. In little over than a year, the accelerator will have been cleared away to make room for its successor, the LHC. The start of the operation goes back to 27 November. Because before setting about the machine with hydraulic shears and monkey wrenches, LEP had first to be made safe - it was important to make sure the machine could be taken apart without risk. All the SPS beam injection systems to LEP were cut off. The fluids used for cooling the magnets and superc...

  5. An impressive start

    CERN Multimedia

    2011-01-01

    This has been an excellent week for the LHC, with a succession of fills rapidly increasing the number of proton bunches to 194 per beam. This has allowed the experiments to reach a peak luminosity of 2.5 × 1032 cm-2s-1, thereby surpassing the record for 2010 where we reached 2.0 × 1032 cm-2s-1. At the time of writing, the integrated luminosity delivered by the LHC in 2011 is around 28 inverse picobarns, which is already more than half of the total 2010 dataset.   These are impressive numbers, but what impresses me most is how quickly the LHC operators are now able to turn the machine around between fills, and how well LHC running has been incorporated into the overall operation of CERN’s accelerator complex. The flexibility of the LHC was illustrated on Thursday when we started a short phase of running at 1.38 TeV per beam, equivalent to the energy-per-nucleon of a lead-ion run. This lower energy data will be used by the experiments, in particular by ALICE, to compare...

  6. ATLAS starts moving in

    CERN Multimedia

    Della Mussia, S

    2004-01-01

    The first large active detector component was lowered into the ATLAS cavern on 1st March. It consisted of the 8 modules forming the lower part of the central barrel of the tile hadronic calorimeter. The work of assembling the barrel, which comprises 64 modules, started the following day. Two road trailers each with 64 wheels, positioned side by side. This was the solution chosen to transport the lower part of the central barrel of ATLAS' tile hadronic calorimeter from Building 185 to the PX16 shaft at Point 1 (see Figure 1). The transportation, and then the installation of the component in the experimental cavern, which took place over three days were, to say the least, rather spectacular. On 25 February, the component, consisting of eight 6-metre modules, was loaded on to the trailers. The segment of the barrel was transported on a steel support so that it wouldn't move an inch during the journey. On 26 February, once all the necessary safety checks had been carried out, the convoy was able to leave Buildi...

  7. Wood fly ash used for nutrient compensation or as a construction material. Environmental impacts related to different management alternatives; Skogsbraensleaska som naeringsresurs eller konstruktionsmaterial. Miljoeeffekter av olika hanteringsalternativ

    Energy Technology Data Exchange (ETDEWEB)

    Olsson, Susanna; Kaerrman, Erik; Roennblom, Tobias; Erlandsson, Aasa (Ecoloop AB, Stockholm (Sweden))

    2008-08-15

    The Swedish Forest Agency recommends that wood ash should be recycled to forest land, if the ashes fulfil certain threshold values. But there is also an option to use the ashes as construction material in forest roads. In this project, an environmental systems analysis approach was developed in order to assess the environmental impact from different alternatives. Three alternatives were analysed for the handling of 1 tonnes wood ash (DM) generated at the municipality of Boraas in Sweden: 1) Spreading the ashes to forests, 2) Use the ashes as a construction material in roads and 3) disposal of the ashes. Both the recycling of wood ash on forests and use of the ash for road construction have benefits in terms of saving natural resources and energy compared to disposal on landfill. Forest-recycling is the most energy efficient alternative and saves most of the resources Zn, P and dolomite. The road construction as well as the landfill alternatives results in a net-removal of the heavy metals As, Cd and Pb from the forests in a 100-year perspective, assuming that the content of these substances in the recycled ash is the same as the amount removed through biomass harvesting. Critical parameters for the results were the assumption that nutrient compensation is needed if wood ashes not are used on forests and the system boundaries chosen for assessing the heavy metal leaching. If the nutrient compensation is not considered as necessary, the influence on the results of transports and maintenance increase. One possibility for further work is to use the developed method for various regions in Sweden. The local conditions vary between different regions in terms of ash production, need for nutrient compensation and potential to build gravel roads etc

  8. An Alternative to Clay in Building Materials: Red Mud Sintering Using Fly Ash via Taguchi’s Methodology

    Directory of Open Access Journals (Sweden)

    Suchita Rai

    2013-01-01

    Full Text Available “Red mud” or “bauxite residue” is a highly alkaline waste generated from alumina refinery with a pH of 10.5–12.5 which poses serious environmental problems. Neutralization or its treatment by sintering in presence of additives is one of the methods for overcoming the caustic problem as it fixes nearly all the leachable free caustic soda present in red mud. In the present study, feasibility of reducing the alkaline nature of red mud by sintering using fly ash as an additive via Taguchi methodology and its use for brick production, as an alternative to clay, is investigated. The analysis of variance (ANOVA shows that sintering temperature is the most significant parameter in the process. A pH of 8.9 was obtained at 25–50% of red mud and 50–75% fly ash with water and temperature of . Alternatively 50% of red mud can be mixed with 50% of fly ash with water at temperature of to get a pH of about 8.4. The mechanism of this process has been explained with also emphasis on chemical, mineralogical, and morphological analysis of the sintered red mud. The results would be extremely useful in utilization of red mud in building and construction industry.

  9. Physico-Chemical Alternatives in Lignocellulosic Materials in Relation to the Kind of Component for Fermenting Purposes

    Directory of Open Access Journals (Sweden)

    Alberto Coz

    2016-07-01

    Full Text Available The complete bioconversion of the carbohydrate fraction is of great importance for a lignocellulosic-based biorefinery. However, due to the structure of the lignocellulosic materials, and depending basically on the main parameters within the pretreatment steps, numerous byproducts are generated and they act as inhibitors in the fermentation operations. In this sense, the impact of inhibitory compounds derived from lignocellulosic materials is one of the major challenges for a sustainable biomass-to-biofuel and -bioproduct industry. In order to minimise the negative effects of these compounds, numerous methodologies have been tested including physical, chemical, and biological processes. The main physical and chemical treatments have been studied in this work in relation to the lignocellulosic material and the inhibitor in order to point out the best mechanisms for fermenting purposes. In addition, special attention has been made in the case of lignocellulosic hydrolysates obtained by chemical processes with SO2, due to the complex matrix of these materials and the increase in these methodologies in future biorefinery markets. Recommendations of different detoxification methods have been given.

  10. In vitro Alternative Methodologies for Central Nervous System Assessment: A Critique using Nanoscale Materials as an Example.

    Science.gov (United States)

    Identifying the potential health hazards to the central nervous system of a new family of materials presents many challenges. Whole-animal toxicity testing has been the tradition, but in vitro methods have been steadily gaining popularity. There are numerous challenges in testing...

  11. Relationship between temperature rise rate of steam turbine cold start-up and hardness value of rotor material%汽轮机冷态启动温升率与转子材料硬度值的关系

    Institute of Scientific and Technical Information of China (English)

    阳萍华; 杨继明; 陈荐; 刘文会; 盛磊

    2011-01-01

    Long time operation of steam turbine rotors under high temperature and high pressure conditions causes the drop of material hardness value, which in its turn affects the material mechanical properties of creep and fatigue and the rotor life expenditure.The temperature field, thermal stress field and hardness value of 300 MW steam turbine were calculated and analyzed by using ALGOR software, the relationships between temperature rise rate and thermal stress, and the effect of temperature rise rate on the fatigue life of rotor were studied,the varying law of hardness value with time was discussed, and with the decline of hardness values, equal life expenditure ratio can be achieved by reducing the temperature rise rate during unit cold start each time.The prediction precision of residual life for defected stream turbine rotor is improved, which provided a basis for safe and reliable operation of the old unit.%汽轮机转子长期在高温、高压状态下运行,会发生材料硬度值下降的现象.硬度的变化影响着材料的疲劳及蠕变力学性能,进而影响着转子寿命损耗.利用ALCOR对300MW汽轮机转子温度场、热应力场及硬度值进行了计算和分析,研究了温升率与热应力的关系以及温升率对转子疲劳寿命的影响,探讨了材料硬度值随时间变化的规律.发现随硬度值下降,可通过降低温升率来实现每次机组冷态启动寿命损耗率相等.提高了转子剩余寿命预测精度,为老机组安全可靠运行提供了依据.

  12. Enhanced electrochemical performance of mesoporous NiCo2O4 as an excellent supercapacitive alternative energy storage material

    Science.gov (United States)

    Bhojane, Prateek; Sen, Somaditya; Shirage, Parasharam M.

    2016-07-01

    Here we report the supercapacitive properties of mesoporous nickel cobalt oxide (NiCo2O4) synthesized by fast, inexpensive and facile chemical bath method, by avoiding high pressure, high temperature and chemical complexity. Physico-chemical characterization techniques such as X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), Raman Spectra, and nitrogen adsorption-desorption isotherm analysis is performed to characterize the electrode material. Brunauer-Emmett-Teller (BET) measurements reveal the surface area 52.86 m2 g-1 and from Barrett-Joyner-Halenda (BJH), typical pores size ranges between 10 and 50 nm, also confirms the mesoporosity. The electrochemical properties are measured by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charging/discharging. The synthesized material exhibits remarkably enhanced electrochemical performance with specific capacitance of 1130 F g-1 at 1 mV s-1 sweep rate and 1125 F g-1 at current density of 0.05 A g-1, highest without supporting base like carbon cloth, Ni-foam, Ti- foil used for direct growth (deposition) of electrode material. It is superior to those of its individual and hybrid components prepared by similar technique. Ragone plot shows high specific energy density (49.25 Wh kg-1) and corresponding specific power density (1851.31 W kg-1) even at high current density of 0.5 A g-1.

  13. Starting a New Chapter

    Directory of Open Access Journals (Sweden)

    Loza-Murguia Manuel G.

    2011-08-01

    Full Text Available In this new stage we want to improve the magazine to make it useful for readers, on the one hand we intend to maintain their accreditation project of the contents of the magazine and on the other hand, the boost in indexing websites popularity, who raise the visibility and therefore coverage to authors and readers who have honored us with their support and we receive frequent visits. Obviously all the works received will remain subject to internal assessment and peer review as usual. Your acceptance will be based on significance, originality and validity of the material presented. The journal is indexed by the time DIALNET. The half-yearly, from 2012 we intend to be a leader in information that is intended to finding solutions to the problems latent, on the other side seeks to raise awareness among professionals and researchers that the publication is a prerequisite to in order to will be clear what is being done as has research in the region. The Journal of the Selva Andina Research Society is a journal founded no more than two years, having failed to publish any number of this enormous amount of material in all this time. We are currently under evaluation by the SciELO Project, Bolivia and have the confidence to be meeting all the criteria that are required to be visible on the website of international prestige. We want to be a reference publication in the journal Public areas both in the international literature (particularly in Latin America and in Bolivia. As Director and Editor in Chief continued in front of it, I thank the Board of the Supreme Council on Science and Biotechnology Research Society Selva Andina renewed confidence in me during these early years, all the items they want be published should be sent to infoselvandina@gmail.com or boliviamanloza@yahoo.com. Following the usual guidelines and rules are expressed in the publication. There is an Editorial Board comprised of leading national and international professional experts who

  14. School Starting Age and Crime

    DEFF Research Database (Denmark)

    Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

    This paper investigates the effects of school starting age on crime while relying on variation in school starting age induced by administrative rules; we exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise to a discontinuity in children’s...... school starting age. Analyses are carried out using register-based Danish data. We find that higher age at school start lowers the propensity to commit crime, but that this reduction is caused by incapacitation while human capital accumulation is unaffected. Importantly, we also find that the individuals...

  15. Development Of An Improved Concrete Roman Tile Alternative Roofing System Using Waste Raw Materials Paper amp Saw Dust As Additives

    OpenAIRE

    Adegoke; C. W.; Abiodun Funmi

    2015-01-01

    ABSTRACT Since the early civilizations in China Neolithic and the Middle East humans have recognized the dual desirable roles of clay tiles as roofing material which remain valid today - First it was an effective means to shed water from buildings and secondly it reduced the spread of fire. The Standard Double Roman tile SDRT was the first roof tile to be mass produced in South Africa. The Double Roman can trace its shape back to Roman engineering principles where it was discovered that arche...

  16. Confine Clay in an Alternating Multilayered Structure through Injection Molding: A Simple and Efficient Route to Improve Barrier Performance of Polymeric Materials.

    Science.gov (United States)

    Yu, Feilong; Deng, Hua; Bai, Hongwei; Zhang, Qin; Wang, Ke; Chen, Feng; Fu, Qiang

    2015-05-20

    Various methods have been devoted to trigger the formation of multilayered structure for wide range of applications. These methods are often complicated with low production efficiency or require complex equipment. Herein, we demonstrate a simple and efficient method for the fabrication of polymeric sheets containing multilayered structure with enhanced barrier property through high speed thin-wall injection molding (HSIM). To achieve this, montmorillonite (MMT) is added into PE first, then blended with PP to fabricate PE-MMT/PP ternary composites. It is demonstrated that alternating multilayer structure could be obtained in the ternary composites because of low interfacial tension and good viscosity match between different polymer components. MMT is selectively dispersed in PE phase with partial exfoliated/partial intercalated microstructure. 2D-WAXD analysis indicates that the clay tactoids in PE-MMT/PP exhibits an uniplanar-axial orientation with their surface parallel to the molded part surface, while the tactoids in binary PE-MMT composites with the same overall MMT contents illustrate less orientation. The enhanced orientation of nanoclay in PE-MMT/PP could be attributed to the confinement of alternating multilayer structure, which prohibits the tumbling and rotation of nanoplatelets. Therefore, the oxygen barrier property of PE-MMT/PP is superior to that of PE-MMT because of increased gas permeation pathway. Comparing with the results obtained for PE based composites in literature, outstanding barrier property performance (45.7% and 58.2% improvement with 1.5 and 2.5 wt % MMT content, respectively) is achieved in current study. Two issues are considered responsible for such improvement: enhanced MMT orientation caused by the confinement in layered structure, and higher local density of MMT in layered structure induced denser assembly. Finally, enhancement in barrier property by confining impermeable filler into alternating multilayer structure through such

  17. A simulation-based and analytic analysis of the off-Hugoniot response of alternative inertial confinement fusion ablator materials

    Science.gov (United States)

    Moore, Alastair S.; Prisbrey, Shon; Baker, Kevin L.; Celliers, Peter M.; Fry, Jonathan; Dittrich, Thomas R.; Wu, Kuang-Jen J.; Kervin, Margaret L.; Schoff, Michael E.; Farrell, Mike; Nikroo, Abbas; Hurricane, Omar A.

    2016-09-01

    The attainment of self-propagating fusion burn in an inertial confinement target at the National Ignition Facility will require the use of an ablator with high rocket-efficiency and ablation pressure. The ablation material used during the National Ignition Campaign (Lindl et al. 2014) [1], a glow-discharge polymer (GDP), does not couple as efficiently as simulations indicated to the multiple-shock inducing radiation drive environment created by laser power profile (Robey et al., 2012). We investigate the performance of two other ablators, boron carbide (B4C) and high-density carbon (HDC) compared to the performance of GDP under the same hohlraum conditions. Ablation performance is determined through measurement of the shock speed produced in planar samples of the ablator material subjected to the identical multiple-shock inducing radiation drive environments that are similar to a generic three-shock ignition drive. Simulations are in better agreement with the off-Hugoniot performance of B4C than either HDC or GDP, and analytic estimations of the ablation pressure indicate that while the pressure produced by B4C and GDP is similar when the ablator is allowed to release, the pressure reached by B4C seems to exceed that of HDC when backed by a Au/quartz layer.

  18. Potential Alternatives for Advanced Energy Material Processing in High Performance Li-ion Batteries (LIBs) via Atmospheric Pressure Plasma Treatment

    Science.gov (United States)

    Duh, Jenq-Gong; Chuang, Shang-I.; Lan, Chun-Kai; Yang, Hao; Chen, Hsien-Wei

    2015-09-01

    A new processing technique by atmospheric pressure plasma (APP) jet treatment of LIBs was introduced. Ar/N2 plasma enhanced the high-rate anode performance of Li4Ti5O12. Oxygen vacancies were discovered and nitrogen doping were achieved by the surface reaction between pristine Li4Ti5O12 and plasma reactive species (N* and N2+). Electrochemical impedance spectra confirm that plasma modification increases Li ions diffusivity and reduces internal charge-transfer resistance, leading to a superior capacity (132 mAh/g) and excellent stability with negligible capacity decay over 100 cycles under 10C rate. Besides 2D material surface treatment, a specially designed APP generator that are feasible to modify 3D TiO2 powders is proposed. The rate capacity of 20 min plasma treated TiO2 exhibited 20% increment. Plasma diagnosis revealed that excited Ar and N2 was contributed to TiO2 surface reduction as companied by formation of oxygen vacancy. A higher amount of oxygen vacancy increased the chance for excited nitrogen doped onto surface of TiO2 particle. These findings promote the understanding of APP on processing anode materials in high performance LIBs.

  19. Nanocrystalline BaSnO3 as an Alternative Gas Sensor Material: Surface Reactivity and High Sensitivity to SO2

    Directory of Open Access Journals (Sweden)

    Artem Marikutsa

    2015-09-01

    Full Text Available Nanocrystalline perovskite-type BaSnO3 was obtained via microwave-assisted hydrothermal route followed by annealing at variable temperature. The samples composition and microstructure were characterized. Particle size of 18–23 nm was unaffected by heat treatment at 275–700 °C. Materials DC-conduction was measured at variable temperature and oxygen concentration. Barium stannate exhibited n-type semiconductor behavior at 150–450 °C with activation energy being dependent on the materials annealing temperature. Predominant ionosorbed oxygen species types were estimated. They were shown to change from molecular to atomic species on increasing temperature. Comparative test of sensor response to various inorganic target gases was performed using nanocrystalline SnO2-based sensors as reference ones. Despite one order of magnitude smaller surface area, BaSnO3 displayed higher sensitivity to SO2 in comparison with SnO2. DRIFT spectroscopy revealed distinct interaction routes of the oxides surfaces with SO2. Barium-promoted sulfate formation favoring target molecules oxidation was found responsible for the increased BaSnO3 sensitivity to ppm-range concentrations of SO2 in air.

  20. Synthesis of a Cementitious Material Nanocement Using Bottom-Up Nanotechnology Concept: An Alternative Approach to Avoid CO2 Emission during Production of Cement

    Directory of Open Access Journals (Sweden)

    Byung Wan Jo

    2014-01-01

    Full Text Available The world’s increasing need is to develop smart and sustainable construction material, which will generate minimal climate changing gas during their production. The bottom-up nanotechnology has established itself as a promising alternative technique for the production of the cementitious material. The present investigation deals with the chemical synthesis of cementitious material using nanosilica, sodium aluminate, sodium hydroxide, and calcium nitrate as reacting phases. The characteristic properties of the chemically synthesized nanocement were verified by the chemical composition analysis, setting time measurement, particle size distribution, fineness analysis, and SEM and XRD analyses. Finally, the performance of the nanocement was ensured by the fabrication and characterization of the nanocement based mortar. Comparing the results with the commercially available cement product, it is demonstrated that the chemically synthesized nanocement not only shows better physical and mechanical performance, but also brings several encouraging impacts to the society, including the reduction of CO2 emission and the development of sustainable construction material. A plausible reaction scheme has been proposed to explain the synthesis and the overall performances of the nanocement.

  1. Development Of An Improved Concrete Roman Tile Alternative Roofing System Using Waste Raw Materials Paper amp Saw Dust As Additives

    Directory of Open Access Journals (Sweden)

    Adegoke

    2015-05-01

    Full Text Available ABSTRACT Since the early civilizations in China Neolithic and the Middle East humans have recognized the dual desirable roles of clay tiles as roofing material which remain valid today - First it was an effective means to shed water from buildings and secondly it reduced the spread of fire. The Standard Double Roman tile SDRT was the first roof tile to be mass produced in South Africa. The Double Roman can trace its shape back to Roman engineering principles where it was discovered that arches have an ability to withstand greater pressures as the arch distributes the weight more evenly down to the base of the structure. However after the initial introduction of the concrete tile to Nigerian roofing market architects began to express displeasure with its unusually heavier weight than other competing roofing materials. Suggestions were made to original manufacturers for product improvement by reducing the overall product weight. Concrete tiles are composite materials made from mixture of Portland cement sharp sand smooth sand and natural fibre. Bolyn Industries 7 has established that a mix ratio by volume of 1cement112sharp sand112smooth sand with some fibre makes a good concrete tile product. The sharp sand provides strength while smooth sand provides smoothness to the concrete surface. This study seeks to improve the current Double Roman product by reducing its overall product weight which is currently at about 5.0 kg to about 4.0 kg. Going by the previous experience with Polycrete invention 2 it is hereby conceived that replacement of smooth sand with lighter waste materials such as paper or saw dust in the concrete tile constituents may achieve the desired product weight reduction. The study investigates the most economic mix ratio of the concrete tile constituents to achieve the desirable engineering properties of light weight strength durability water tightness and rust-proofness. Results with preliminary mix trials indicate that replacement

  2. EFFECTS OF ALTERNATIVE RAW MATERIALS AND VARYING RESIN CONTENT ON MECHANICAL AND FRACTURE MECHANICAL PROPERTIES OF PARTICLE BOARD

    Directory of Open Access Journals (Sweden)

    Jörn Rathke,

    2012-05-01

    Full Text Available Particle boards were produced from different types of wood particles, i.e. spruce, recovered particles, willow, poplar, and locust. Effects of raw material, as well as varying resin content on mechanical and fracture mechanical properties were investigated. For the analysis of mechanical properties, specific fracture energy, stress intensity factors, and the industrial European standard methods internal bond strength according to EN 319 and bending strength according to EN 310 were used. The total fracture energy was measured, and the stress intensity factor was calculated by means of data achieved through finite element simulations. Results of the fracture energy analysis were compared to internal bond strength (IB and bending strength. While IB and the modulus of elasticity (MOE showed a high variability, data scattering for fracture energy tests and modulus of rupture (MOR were smaller, which are due to significant differences between the resin contents of the various board types.

  3. Carbon/PEEK composite materials as an alternative for stainless steel/titanium hip prosthesis: a finite element study.

    Science.gov (United States)

    Rezaei, Farshid; Hassani, Kamran; Solhjoei, Nosratollah; Karimi, Alireza

    2015-12-01

    Total hip replacement (THR) has been ranked within the most typical surgical processes in the world. The durability of the prosthesis and loosening of prosthesis are the main concerns that mostly reported after THR surgeries. In THR, the femoral prosthesis can be fixed by either cement or cementless methods in the patient's bones. In both procedures, the stability of the prosthesis in the hosted bone has a key asset in its long-term durability and performance. This study aimed to execute a comparative finite element simulation to assess the load transfer between the prosthesis, which is made of carbon/PEEK composite and stainless steel/titanium, and the femur bone. The mechanical behavior of the cortical bone was assumed as a linear transverse isotropic while the spongy bone was modeled like a linear isotropic material. The implants were made of stainless steel (316L) and titanium alloy as they are common materials for implants. The results showed that the carbon/PEEK composites provide a flatter load transfer from the upper body to the leg compared to the stainless steel/titanium prosthesis. Furthermore, the results showed that the von Mises stress, principal stress, and the strain in the carbon/PEEK composites prosthesis were significantly lower than that made of the stainless steel/titanium. The results also imply that the carbon/PEEK composites can be applied to introduce a new optimum design for femoral prosthesis with adjustable stiffness, which can decrease the stress shielding and interface stress. These findings will help clinicians and biomedical experts to increase their knowledge about the hip replacement.

  4. Alternative p-doped hole transport material for low operating voltage and high efficiency organic light-emitting diodes

    International Nuclear Information System (INIS)

    We investigate the properties of N,N′-[(Diphenyl-N,N′-bis)9,9,-dimethyl-fluoren-2-yl]-benzidine (BF-DPB) as hole transport material (HTL) in organic light-emitting diodes (OLEDs) and compare BF-DPB to the commonly used HTLs N,N,N′,N′-tetrakis(4-methoxyphenyl)-benzidine (MeO-TPD), 2,2′,7,7′-tetrakis(N,N′-di-p-methylphenylamino)-9,9′-spirobifluorene (Spiro-TTB), and N,N′-di(naphtalene-1-yl)-N,N′-diphenylbenzidine (NPB). The influence of 2,2′-(perfluoronaphthalene-2,6-diylidene)dimalononitrile (F6-TCNNQ p-dopant) concentration in BF-DPB on the operation voltage and efficiency of red and green phosphorescent OLEDs is studied; best results are achieved at 4 wt. % doping. Without any light extraction structure, BF-DPB based red (green) OLEDs achieve a luminous efficacy of 35 .1 lm/W (74 .0 lm/W) at 1000 cd/m2 and reach a very high brightness of 10 000 cd/m2 at a very low voltage of 3.2 V (3.1 V). We attribute this exceptionally low driving voltage to the high ionization potential of BF-DPB which enables more efficient hole injection from BF-DPB to the adjacent electron blocking layer. The high efficiency and low driving voltage lead to a significantly lower luminous efficacy roll-off compared to the other compounds and render BF-DPB an excellent HTL material for highly efficient OLEDs.

  5. Alternative security

    International Nuclear Information System (INIS)

    This book contains the following chapters: The Military and Alternative Security: New Missions for Stable Conventional Security; Technology and Alternative Security: A Cherished Myth Expires; Law and Alternative Security: Toward a Just World Peace; Politics and Alternative Security: Toward a More Democratic, Therefore More Peaceful, World; Economics and Alternative Security: Toward a Peacekeeping International Economy; Psychology and Alternative Security: Needs, Perceptions, and Misperceptions; Religion and Alternative Security: A Prophetic Vision; and Toward Post-Nuclear Global Security: An Overview

  6. Implementation of START and beyond

    International Nuclear Information System (INIS)

    Implementation of START negotiations and agreement invokes an image of an evolving arms control agenda in which the achievements of the START process will provide the foundations for genuine disarmament. The contributions of START I and START II (to date unratified) are indeed significant. Once implemented in 3003, the new agreement will reduce the two nations' (USA and Russia) strategic inventories to some 7000 weapons - less than one-third of the levels established by the 1991 Strategic Reduction Talks. More important, it will completely eliminate both sides' most destabilizing weapons - land based missiles with multiple independently targetable warheads

  7. Steel slag: a waste industrial by-product as an alternative sustainable green building material in construction applications--an attempt for solid waste management.

    Science.gov (United States)

    Pofale, Arun D; Nadeem, Mohammed

    2012-01-01

    This investigation explores the possibility of utilizing granular slag as an alternative to fine aggregate (natural sand) in construction applications like masonry and plastering. Construction industry utilizes large volume of fine aggregate in all the applications which has resulted into shortage of good quality naturally available fine aggregate. Use of granular slag serves two fold purposes, i.e. waste utilisation as well as alternative eco-friendly green building material for construction. The investigation highlights comparative study of properties with partial and full replacement of fine aggregate (natural sand) by granular slag in cement mortar applications (masonry and plastering). For this purpose, cement mortar mix proportions from 1:3, 1:4, 1:5 & 1:6 by volume were selected for 0, 25, 50, 75 & 100% replacement levels with w/c ratios of 0.60, 0.65, 0.70 & 0.72 respectively. Based on the study results, it could be inferred that replacement of natural sand with granular slag from 25 to 75% increased the packing density of mortar which resulted into reduced w/c ratio, increased strength properties of all mortar mixes. Hence, it could be recommended that the granular slag could be effectively utilized as fine aggregate in masonry and plastering applications in place of conventional cement mortar mixes using natural sand.

  8. Alternative energies; Energies alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Bonal, J.; Rossetti, P

    2007-07-01

    The earth took millions years to made the petroleum, the gas the coal and the uranium. Only a few centuries will be needed to exhaust these fossil fuels and some years to reach expensive prices. Will the wold continue on this way of energy compulsive consumption? The renewable energies and some citizen attitudes are sufficient to break this spiral. This book proposes to discuss these alternative energies. It shows that this attitude must be supported by the government. It takes stock on the more recent information concerning the renewable energies. it develops three main points: the electricity storage, the housing and the transports. (A.L.B.)

  9. Studies on the chemical conditions and microstructure in the reference bentonites of alternative buffer materials project (ABM) in Aespoe

    Energy Technology Data Exchange (ETDEWEB)

    Muurinen, A. (VTT Technical Research Centre of Finland, Espoo (Finland))

    2009-06-15

    The chemical and microstructural properties of some bentonites used in the ABM project in Aespoe HRL were studied in laboratory experiments. The aim was to obtain information about the materials before they were used in the field experiment and to test the research methods that will be used when the packages of the field experiment are retrieved. The bentonites of interest were MX-80, Deponit CAN, Asha 505 and Friedland Clay. The pH values in the compacted samples prepared from the clay powders and deionized water were about 8 for MX-80, 7 for Deponit and Asha, and 6.5 for Friedland clay. The Eh values in the compacted MX-80, Asha and Deponit samples varied between 100 mV and -100 mV, and in the Friedland clay from 0 mV to 200 mV. The total porosity, chloride porosity and the microstructure were studied in compacted samples prepared from MX-80, Deponit, Asha and Friedland Clay and equilibrated through filter plates with 0.1 M NaCl solution for 12.5 months in aerobic conditions. The dry densities of the samples were approximately 0.7, 1.0, 1.25 and 1.55 g/cm3. XRD and SAXS (Small Angle X-ray Scattering) were used to study the microstructure of the MX-80 and Deponit bentonites. It was obvious that the chloride porosity was lower than the water porosity in all the clays, which indicates the exclusion of anions caused by the negatively charged surfaces. In the XRD measurements on MX-80, Asha and Deponit, the measured basal spaces represented by the diffraction peaks were smaller than the theoretical one assuming a homogenous microstructure. This indicates that there was a substantial amount of water also in the pores, which were not seen by XRD. The SAXS data modelling which considered single discs and stacks of discs proposed that a large fraction of the clay should be considered as single platelets. The fraction of the single discs decreased with the increasing density of the sample. The number of layers in the stacks varied from 4 to 8. By combining the information

  10. Alternative additives; Alternative additiver

    Energy Technology Data Exchange (ETDEWEB)

    2007-08-15

    In this project a number of industrial and agricultural waste products have been characterised and evaluated in terms of alkali-getter performance. The intended use is for biomass-fired power stations aiming at reducing corrosion or slagging related problems. The following products have been obtained, characterised and evaluated: 1) Brewery draff 2) Danish de-gassed manure 3) Paper sludge 4) Moulding sand 5) Spent bleaching earth 6) Anorthosite 7) Sand 8) Clay-sludge. Most of the above alternative additive candidates are deemed unsuitable due to insufficient chemical effect and/or expensive requirements for pre-treatment (such as drying and transportation). 3 products were selected for full-scale testing: de-gassed manure, spent bleaching earth and clay slugde. The full scale tests were undertaken at the biomass-fired power stations in Koege, Slagelse and Ensted. Spent bleaching earth (SBE) and clay sludge were the only tested additive candidates that had a proven ability to react with KCl, to thereby reduce Cl-concentrations in deposits, and reduce the deposit flux to superheater tubes. Their performance was shown to nearly as good as commercial additives. De-gassed manure, however, did not evaluate positively due to inhibiting effects of Ca in the manure. Furthermore, de-gassed manure has a high concentration of heavy metals, which imposes a financial burden with regard to proper disposal of the ash by-products. Clay-sludge is a wet clay slurring, and drying and transportation of this product entails substantial costs. Spent bleaching does not require much pre-treatment and is therefore the most promising alternative additive. On the other hand, bleaching earth contains residual plant oil which means that a range of legislation relating to waste combustion comes into play. Not least a waste combustion fee of 330 DKK/tonne. For all alternative (and commercial) additives disposal costs of the increase ash by-products represents a significant cost. This is

  11. Preparation of biological samples for transmission X-ray microanalysis: a review of alternative procedures to the use of sectioned material

    International Nuclear Information System (INIS)

    Although transmission X-ray microanalysis of biological material has traditionally been carried out mainly on sectioned preparations, a number of alternative procedures exist. These are considered under three major headings - whole cell preparations, analysis of cell homogenates and biological fluids, and applications of the technique to microsamples of purified biochemicals. These three aspects provide a continuous range of investigative level - from the cellular to the molecular. The use of X-ray microanalysis with whole cell preparations is considered in reference to eukaryote (animal) cells and prokaryotes - where it has particular potential in environmental studies on bacteria. In the case of cell homogenates and biological fluids, the technique has been used mainly with microdroplets of animal material. The use of X-ray microanalysis with purified biochemicals is considered in relation to both particulate and non-particulate samples. In the latter category, the application of this technique for analysis of thin films of metalloprotein is particularly emphasised. It is concluded that wider use could be made of the range of preparative techniques available - both within a particular investigation, and in diverse fields of study. Transmission X-ray microanalysis has implications for environmental, physiological and molecular biology as well as cell biology

  12. Advances in Tube Hydroforming - An Enabling Technology for Low-Mass Vehicle Manufacturing - Material, Lubrication,Loading, Simulation Issues, and Alternatives

    Institute of Scientific and Technical Information of China (English)

    Muammer Ko(c)

    2004-01-01

    The tube hydroforming process (THF) has recently found a wide application opportunity in the automotive industry, and is of increasing interest to other industries as well. The increased interest stems from the fact that, through the THF process, manufacturers are able to produce complex, consolidated, lightweight parts with reduced number of post-processing than through alternative metal forming techniques. In order to fully realize the benefits of this technology, various aspects have been under investigation in academia and industry world-wide. In this paper, effect of loading path, incoming material variation, and lubrication on the robustness of the hydroforming process and final part specifications are summarized based on previous experimental and computational work. In addition, the simulation of hydroforming and examples are presented in comparison with experimental findings. Briefly, results emphasized the importance of the loading path design whereas material variation within the experimentally tested range was not found to be significantly effective on the final part specifications. Selection of a lubricant for hydroforming of a frame rail part was presented demonstrating several aspects of lubrication selection methodology. Results of friction experiments show that only thickness, axial feeding, and force measurements are good indications of lubricant performance as these are found to be strongly discriminative.

  13. Accountability Starts with the Superintendent

    Science.gov (United States)

    Ricketts, Kenneth E.

    1973-01-01

    Describes how Lawndale District, near Los Angeles, developed a system of accountability starting with the superintendent. Describes the subgoals and objectives developed by the superintendent in cooperation with the Board of Trustees and members of the community. (JF)

  14. Montessori Head Start Implementation Brief.

    Science.gov (United States)

    Clifford, Alcillia; Kahn, David

    1995-01-01

    Discusses the use of the Montessori method in Head Start programs, focusing on educational environment, teacher training, parent involvement, and funding. Outlines the phased implementation of a Montessori program and provides a list of Montessori publications and organizations. (MDM)

  15. The Use of Alternate Ligno-cellulosic Raw Materials Banana (Musa sapientum Ankara (Calotropis procera and Pineapple (Ananas comosus in Handmade Paper & their Blending with Waste Paper.

    Directory of Open Access Journals (Sweden)

    Atul Kumar

    2013-09-01

    Full Text Available The studies were made to established suitability of lingo-cellulosic raw materials namely leaf fibreBanana (Musa Sapientum, bast fibre Ankara (Calotropis Procera, & leaf fibre Pineapple (Ananas Comosus for making pulps for handmade paper industry. This should help in providing a cost effective, good quality cellulosic raw material as an alternate to cost prohibitive traditionally used cotton hosiery waste traditionally used for manufacturing good quality handmade paper & it’s products. This will help in improving the cost economics & competitiveness of the Indian paper industry in the global market besides addressing the problems of environment & global warming. The aim of the research was to study the extraction, morphology, chemical composition and pulping of these fibres and relate these properties to the composite properties obtained with these fibres as reinforcement with short fibres viz. waste paper. For the pulp production to be feasible it is essential to use suitable pulping methods, which maximize the yield of pulp and introduce as low damage as possible to the fibres. The different pulping methods were applied to these fibre to get optimized strength properties papers. The Studies thus carried out provide useful information about the nature of these raw materials, suitable pulping & bleaching process to produce an eco-friendly handmade paper and converted products. The research work provides a good quality cost effective lingo-cellulosic raw material for handmade paper industries with a possibility of replacement of the expensive and traditionally used cotton hosiery waste.The paper thus produced using environmental friendly pulping and bleaching process is characterized for its strength properties like tensile, tear, bursting, folding endurance and other parameters. The effluents generated from pulping and bleaching of above ligno-cellulosic waste materials were characterized for various pollution parameters like Residual Alkali

  16. Improving NPT safeguards. Particularly at the natural uranium starting point

    International Nuclear Information System (INIS)

    According to the Non Proliferation Treaty (NPT) all nuclear material is subject to safeguards, but according to INFCIRC/153 the full range of safeguards is only applied beyond the 'starting point of safeguards', that is: The point at which nuclear material has reached a composition and purity suitable for fuel fabrication or enrichment. This paper addresses the two questions: (a) is the starting point adequately defined, and (b) what mesures could be applied to nuclear material before the starting point? Those questions have been asked before, some of the answers in this paper are new. (orig.)

  17. Argus II retinal prosthesis implantation with scleral flap and autogenous temporalis fascia as alternative patch graft material: a 4-year follow-up

    Science.gov (United States)

    Matet, Alexandre; Amar, Nawel; Mohand-Said, Saddek; Sahel, José-Alain; Barale, Pierre-Olivier

    2016-01-01

    Introduction The Argus II retinal prosthesis is composed of an epiretinal electrode array positioned over the macula and connected to an extrascleral electronics case via a silicone cable, running through a sclerotomy. During implantation, the manufacturer recommends to cover the sclerotomy site with a patch of processed human pericardium to prevent postoperative hypotony and conjunctival erosion by the underlying electronics case. Due to biomedical regulations prohibiting the use of this material in France, we developed an alternative technique combining a scleral flap protecting the sclerotomy and an autogenous graft of superior temporalis fascia overlying the electronics case. Methods The purpose of this study is to describe the 4-year outcomes of this modified procedure in three subjects who underwent Argus II Retinal Prosthesis System implantation. Clinical data consisting of intraocular pressure measurements and tolerance in terms of conjunctival erosion or inflammation were retrospectively assessed over a 4-year postoperative follow-up. Results None of the three patients implanted with the modified technique developed ocular hypotony over 4 years. A normal, transient conjunctival inflammation occurred during the first postoperative month but conjunctival erosion was not observed in any of the three patients over 4 years. Four years after implantation, the autogenous temporalis fascia graft remained well tolerated and the retinal prosthesis was functional in all three patients. Conclusion The combination of an autograft of superficial temporalis fascia and a scleral flap efficiently prevented leakage through the sclerotomy site, ocular hypotony, and conjunctival erosion by the extrascleral electronics case. This modified technique is suitable for the implantation of existing and forthcoming retinal prostheses. Superficial temporalis fascia may also be used as alternative to commercial tectonic tissues for scleral wound repair in clinical settings where they

  18. A Direct, Biomass-Based Synthesis of Benzoic Acid: Formic Acid-Mediated Deoxygenation of the Glucose-Derived Materials Quinic Acid and Shikimic Acid

    Energy Technology Data Exchange (ETDEWEB)

    Arceo, Elena; Ellman, Jonathan; Bergman, Robert

    2010-05-03

    An alternative biomass-based route to benzoic acid from the renewable starting materials quinic acid and shikimic acid is described. Benzoic acid is obtained selectively using a highly efficient, one-step formic acid-mediated deoxygenation method.

  19. Start a Research on Biopolymer Polyhydroxyalkanoate (PHA: A Review

    Directory of Open Access Journals (Sweden)

    Giin-Yu Amy Tan

    2014-03-01

    Full Text Available With the impending fossil fuel crisis, the search for and development of alternative chemical/material substitutes is pivotal in reducing mankind’s dependency on fossil resources. One of the potential substitute candidates is polyhydroxyalkanoate (PHA. PHA is a carbon-neutral and valuable polymer that could be produced from many renewable carbon sources by microorganisms, making it a sustainable and environmental-friendly material. At present, PHA is not cost competitive compared to fossil-derived products. Encouraging and intensifying research work on PHA is anticipated to enhance its economic viability in the future. The development of various biomolecular and chemical techniques for PHA analysis has led to the identification of many PHA-producing microbial strains, some of which are deposited in culture collections. Research work on PHA could be rapidly initiated with these ready-to-use techniques and microbial strains. This review aims to facilitate the start-up of PHA research by providing a summary of commercially available PHA-accumulating microbial cultures, PHA biosynthetic pathways, and methods for PHA detection, extraction and analysis.

  20. STARTing Again: What Happens After START I Expires?

    International Nuclear Information System (INIS)

    The Strategic Arms Reduction Treaty (START I), a seminal arms control agreement that substantially reduced the levels of deployed strategic nuclear arms in the United States and Russia, will expire in December 2009. At this time, it is unclear what - if anything - will replace it. While the treaty remains relevant, more than a simple extension is appropriate. Instead the authors advocate for a successor regime that builds on the START I legacy but does not rely on the traditional tools of arms control. This paper examines the strategic context in which a successor regime would be developed and proposes several recommendations for future action

  1. Report of material and equipment section`s activities at New York Shipbuilding Corporation during fabrication of AXC 167 1/2 starting May 18, 1951. Part 7, Section 3

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, J.R.

    1954-04-28

    This document provides Part VII, Section III and Section IV of the report of the Material and Equipment Section`s activities at the New York Shipbuilding Corporation. The fabrication, inspection, and testing of reactor components is detailed.

  2. Multi-walled carbon nanotubes as alternative reversed-dispersive solid phase extraction materials in pesticide multi-residue analysis with QuEChERS method.

    Science.gov (United States)

    Zhao, Pengyue; Wang, Lei; Zhou, Li; Zhang, Fengzu; Kang, Shu; Pan, Canping

    2012-02-17

    A multi-residue method based on modified QuEChERS sample preparation with multi-walled carbon nanotubes (MWCNTs) as reversed-dispersive solid phase extraction (r-DSPE) material and gas chromatography-mass spectrometry determination by selected ion monitoring (GC/MS-SIM) mode was validated on 30 representative pesticides residues in vegetables and fruits. The acetonitrile-based QuEChERS (quick, easy, cheap, effective, rugged and safe) sample preparation technique was used to obtain the extracts, and the further cleanup was carried out by applying r-DSPE. It was found that the amount of MWCNTs influenced the cleanup performance and the recoveries. The optimal amount of 10mg MWCNTs was suitable for cleaning up all selected matrices, as a suitable alternative r-DSPE material to primary secondary amine (PSA). This method was validated on cabbage, spinach, grape and orange spiked at concentration levels of 0.02 and 0.2 mg/kg. The recoveries of 30 pesticides were in the range of 71-110%, with relative standard deviations (RSDs, n=5) lower than 15%. Matrix effects were observed by comparing the slope of matrix-matched standard calibration with that of solvent. Good linearity was achieved at the concentration levels of 0.02-0.5 mg/L. The limits of quantification (LOQs) and the limits of detection (LODs) for 30 pesticides ranged from 0.003 to 0.05 mg/kg and 0.001 to 0.02 mg/kg at the signal-to-noise ratio (S/N) of 10 and 3, respectively. The method was successfully applied to analysis real samples in Beijing. In conclusion, the modified QuEChERS method with MWCNTs cleanup step showed reliable method validation performances and good cleanup effects in this study. PMID:22227363

  3. Dynamic usage of transcription start sites within core promoters

    DEFF Research Database (Denmark)

    Kawaji, Hideya; Frith, Martin C; Katayama, Shintaro;

    2006-01-01

    BACKGROUND: Mammalian promoters do not initiate transcription at single, well defined base pairs, but rather at multiple, alternative start sites spread across a region. We previously characterized the static structures of transcription start site usage within promoters at the base pair level......, based on large-scale sequencing of transcript 5' ends. RESULTS: In the present study we begin to explore the internal dynamics of mammalian promoters, and demonstrate that start site selection within many mouse core promoters varies among tissues. We also show that this dynamic usage of start sites...... is associated with CpG islands, broad and multimodal promoter structures, and imprinting. CONCLUSION: Our results reveal a new level of biologic complexity within promoters--fine-scale regulation of transcription starting events at the base pair level. These events are likely to be related to epigenetic...

  4. Secondary Circuit Start Up Chemistry Optimisation

    International Nuclear Information System (INIS)

    In a context of investment and renewal of equipment, Electricite De France (EDF) put enhanced efforts on operating practices during start-up of the secondary circuit, in order to improve operational performance and materials lifetime. This article focuses on the objective of optimizing the filling, the chemical conditioning and the thermal conditioning of the secondary fluid, while taking into account the following issues: - Limiting the time required to obtain a proper chemistry, - Limiting the amount of water and steam used, - Limiting the amount of effluent generated. The scope is all start-up conditions of secondary circuit, both after refuelling outage or fortuitous shutdowns of the plant. The recommendations produced are based on existing local procedures and good practices, which were collected and developed in order to propose a generic methodology understandable and useful both for operators, chemists and managers. (authors)

  5. Math Club Starting in Kindergarten

    Science.gov (United States)

    Perry, Ann M.

    2011-01-01

    Starting a math club as early as kindergarten and having a range of grade levels in attendance can be successful. With the help of the older students, the varied age groups are entertained and excited about attending math club. The purpose of the club is to enrich the classroom mathematics curriculum with hands-on activities and to have members…

  6. Double Star Mission Starts Countdown

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    @@ As of July, scientists at the CAS Center for Space Science and Applied Research (CSSAR) have been busy modulating and testing the payloads that will be onboard a space exploration satellite, marking the start of the countdown for China's Double Star Project.

  7. Sulfur plant start-up

    Energy Technology Data Exchange (ETDEWEB)

    Hudson, Hank; Grigson, Susan [Ortloff Engineers Ltd. (United States)

    2002-02-01

    The authors discuss an Ortloff sulfur plant design concept using the Claus reaction that differs from accepted 'industry practice': cold reactor bed start-up. The process is designed to eliminate catalyst sulfation, heat damage and furnace overheating in sulfur recovery units. (UK)

  8. "The greatest comebacks start here".

    Science.gov (United States)

    Confalone, Daniel C

    2005-06-01

    When the marketing department at Good Shepherd Rehabilitation Network in Allentown, Pa., came up with the slogan "The Greatest Comebacks Start Here", it wasn't thinking of the hospital's finances. But it easily could have been. Daniel C. Confalone, FHFMA, helped coordinate the system's revenue cycle comeback, from 150 days in accounts receivable to just 55. PMID:17240662

  9. Argus II retinal prosthesis implantation with scleral flap and autogenous temporalis fascia as alternative patch graft material: a 4-year follow-up

    Directory of Open Access Journals (Sweden)

    Matet A

    2016-08-01

    Full Text Available Alexandre Matet,1,2 Nawel Amar,1,2 Saddek Mohand-Said,1–4 José-Alain Sahel,1–7 Pierre-Olivier Barale1,2 1INSERM and DHOS, CHNO des Quinze-Vingts, 2Sorbonne Universités, UPMC Univ Paris 6, Institut de la Vision, 3INSERM, 4CNRS, Paris, France; 5Institute of Ophthalmology, University College London, London, UK; 6Fondation Ophtalmologique Adolphe de Rothschild, 7Académie des Sciences, Institut de France, Paris, France Introduction: The Argus II retinal prosthesis is composed of an epiretinal electrode array positioned over the macula and connected to an extrascleral electronics case via a silicone cable, running through a sclerotomy. During implantation, the manufacturer recommends to cover the sclerotomy site with a patch of processed human pericardium to prevent postoperative hypotony and conjunctival erosion by the underlying electronics case. Due to biomedical regulations prohibiting the use of this material in France, we developed an alternative technique combining a scleral flap protecting the sclerotomy and an autogenous graft of superior temporalis fascia overlying the electronics case. Methods: The purpose of this study is to describe the 4-year outcomes of this modified procedure in three subjects who underwent Argus II Retinal Prosthesis System implantation. Clinical data consisting of intraocular pressure measurements and tolerance in terms of conjunctival erosion or inflammation were retrospectively assessed over a 4-year postoperative follow-up. Results: None of the three patients implanted with the modified technique developed ocular hypotony over 4 years. A normal, transient conjunctival inflammation occurred during the first postoperative month but conjunctival erosion was not observed in any of the three patients over 4 years. Four years after implantation, the autogenous temporalis fascia graft remained well tolerated and the retinal prosthesis was functional in all three patients. Conclusion: The combination of an

  10. Decoherent Histories Quantum Mechanics Starting with Records of What Happens

    CERN Document Server

    Hartle, James B

    2016-01-01

    We present a formulation of the decoherent (or consistent) histories quantum theory of closed systems starting with records of what histories happen. Alternative routes to a formulation of quantum theory like this one can be useful both for understanding quantum mechanics and for generalizing and extending it to new realms of application and experimental test.

  11. Biomechanics of the sprint start.

    Science.gov (United States)

    Harland, M J; Steele, J R

    1997-01-01

    Many variables have been studied pertaining to the block sprint start. Research suggests that the adoption of a medium block spacing is preferred, with front and rear knee angles in the set position approximating 90 and 130 degrees, respectively, with the hips held moderately high. The sprinter must be capable of developing a high force rate combined with a high maximum force, especially in the horizontal direction. This ability to create high force underlies other important indicators of starting performance such as minimum block clearance time, maximum block leaving velocity and maximum block leaving acceleration. Once the sprinter has projected him/herself from the blocks at a low angle (40 to 45 degrees) relative to the ground, the following 2 post-block steps should occur with the total body centre of gravity ahead of the contacting foot at foot strike to minimise potential horizontal braking forces.

  12. Getting started with Twitter Flight

    CERN Document Server

    Hamshere, Tom

    2013-01-01

    Getting Started with Twitter Flight is written with the intention to educate the readers, helping them learn how to build modular powerful applications with Flight, Twitter's cutting-edge JavaScript framework.This book is for anyone with a foundation in JavaScript who wants to build web applications. Flight is quick and easy to learn, built on technologies you already understand such as the DOM, events, and jQuery.

  13. Getting started with Drupal commerce

    CERN Document Server

    Jones, Richard

    2013-01-01

    A simple yet concise step-by-step tutorial that starts from scratch and builds up your knowledge with focused examples that will enable you to set up and run an e-commerce website.This book is for beginners and will take you through the installation and configuration of Drupal Commerce from scratch, but some familiarity with Drupal 7 will be an advantage. All examples are based on development on a local computer - you do not need a hosted Drupal environment.

  14. Electrosíntesis y caracterización de materiales moleculares a partir de derivados n-trifluorometansulfonil-1-azahexa-1,3,5-trienos. // Electrosintesis and characterization of molecular materials starting from having derived.

    Directory of Open Access Journals (Sweden)

    M. E. Sánchez Vergara

    2008-01-01

    Full Text Available Actualmente existe un interés creciente en los Materiales Moleculares, ya que estos pueden presentar diferentescomportamientos eléctricos que van desde aislantes, semiconductores o bien conductores. En el presente estudio fueronsintetizados materiales de este tipo, a partir de derivados N-Trifluorometansulfonil-1-azahexa-1,3,5-trienos yK3[Cr(C2O43]•3H2O debido a que estos compuestos representan un gran interés por sus variadas aplicaciones en camposcomo la química analítica, además los derivados N-Trifluorometansulfonil-1-azahexa-1,3,5-trienos resultan especialmenteatractivos desde el punto de vista estructural ya que en su forma neutra presentan una extensa deslocalización electrónica locual les confiere un comportamiento químico muy particular. En esta comunicación, se forman mediante electrosíntesisconvencional y mediante electrosíntesis en el módulo de electrocristalización del microscopio de fuerza atómica (AFM,algunos materiales moleculares. Una vez obtenidos dichos materiales, se caracterizan por análisis elemental sobresuperficies (SEM-EDS.Palabras claves: Materiales moleculares, anisotropía, electrocristalización._____________________________________________________________________________Abstract.Recently, molecular materials have been developed because of their electrical properties which give conductor,semiconductor, or superconductor behavior. In this work, the synthesis of new materials formed from Ntrifluoromethanesulfonyl-1-azahexa-1, 3, 5-triene species and K3[Cr(C2O43]•3H2O is reported. NTrifluoromethanesulfonyl-1-azahexa-1,3,5-trienes compounds, which are highly functionalised pentametines, have alsobeen studied due to its interesting physical and chemical properties. These compounds are especially interesting from astructural point of view for some reasons; in a neutral form, they show an extensive electronic delocalisation, which confersthem a very particular chemical behaviour. This study is focused on

  15. Getting started With Amazon Redshift

    CERN Document Server

    Bauer, Stefan

    2013-01-01

    Getting Started With Amazon Redshift is a step-by-step, practical guide to the world of Redshift. Learn to load, manage, and query data on Redshift.This book is for CIOs, enterprise architects, developers, and anyone else who needs to get familiar with RedShift. The CIO will gain an understanding of what their technical staff is working on; the technical implementation personnel will get an in-depth view of the technology, and what it will take to implement their own solutions.

  16. New Start,New Opportunity

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Daniel Arbenz was bom and educated in Switzerland. In 1978, he entered the hotel indastry as a chef and worked his way up through all segments of the business. After graduating from the famous Swiss Hotel Management School in Luceme and obtaining management exposure in the finest hotels in Switzerland, he moved to Hong Kong in 1989, starting his career in Asia. Arbenz moved to Singapore, then to Bali, for Resort Hotels and has been with the Intercontinental Hotels Group for almost 10 years in general man...

  17. Starting of nuclear power stations

    International Nuclear Information System (INIS)

    The procedure is briefly characterized of jobs in nuclear power plant start-up and the differences are pointed out from those used in conventional power generation. Pressure tests are described oriented to tightness, tests of the secondary circuit and of the individual nodes and facilities. The possibility is shown of increased efficiency of such jobs on an example of the hydraulic tests of the second unit of the Dukovany nuclear power plant where the second and the third stages were combined in the so-colled integrated hydraulic test. (Z.M.). 5 figs

  18. Alternative Structures and Bihamiltonian Systems

    CERN Document Server

    Marmo, G; Simoni, A; Ventriglia, F

    2002-01-01

    In the study of bi-Hamiltonian systems (both classical and quantum) one starts with a given dynamics and looks for all alternative Hamiltonian descriptions it admits.In this paper we start with two compatible Hermitian structures (the quantum analog of two compatible classical Poisson brackets) and look for all the dynamical systems which turn out to be bi-Hamiltonian with respect to them.

  19. The start of the harvest

    CERN Multimedia

    2011-01-01

    The first major particle physics summer conference has just started this week in Grenoble. After the Quark-Matter conference, the Europhysics Conference on High-Energy Physics marks the start of a promising harvest for the LHC experiments.   For the first time, the collaborations will be presenting their latest results based on all luminosity taken until end of June, which will provide more precise measurements in many areas. Thanks to the excellent performance of the LHC, the experiments have already accumulated a substantial quantity of data allowing them to push back the known limits and refine measurements in many fields ranging from b physics to the search for the Higgs boson and for dark matter. At the time of writing, the LHC collaborations are about to present these new results in an energy range which has never previously been explored. I have congratulated all the teams involved in getting the LHC into operation in record time with great efficiency. Today I would like to acknowledge the...

  20. A novel induction motor starting method using superconduction

    International Nuclear Information System (INIS)

    Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method

  1. A novel induction motor starting method using superconduction

    Energy Technology Data Exchange (ETDEWEB)

    Silva, F.B.B., E-mail: flaviobarcelos@ifes.edu.br [Ifes – Federal Institute of Espírito Santo, Dept. of Industrial Automation, Serra, ES 29173087 (Brazil); UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Orlando, M.T.D. [UFES – Federal University of Espírito Santo, Dept. of Physics, Vitória, ES (Brazil); Fardin, J.F.; Simonetti, D.S. [UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Baldan, C.A. [EEL/USP – Engineering School from Lorena/University of São Paulo, SP (Brazil)

    2014-12-15

    Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method.

  2. Regional Applied Research Effort Project (RARE) with Region 8 - Beneficial Use of Red and Brown Mud and Phosphogypsum as Alternative Construction Materials

    Science.gov (United States)

    Red and brown muds are the secondary materials generated from the extraction of alumina from bauxite, an aluminum-containing sedimentary rock (Ref. 2). Phosphogypsum is the secondary material generated by the phosphorous fertilizer industry from phosphate-containing sedimentary ...

  3. Alternative Treatments

    Science.gov (United States)

    ... Find your chapter: search by state Home > Alzheimer's Disease > Treatments > Alternative Treatments Overview What Is Dementia? What Is Alzheimer's? Younger/Early Onset Facts and Figures Know the 10 Signs Stages Inside the Brain: ...

  4. 30 CFR 75.1913 - Starting aids.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Starting aids. 75.1913 Section 75.1913 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1913 Starting aids. (a) Volatile fuel starting aids shall be used in accordance with recommendations provided by the starting...

  5. Potentials of the separation of cow manure. Utilization of solid materials as an alternative fermentation substrate in biogas conversion plants; Potentiale der Rinderguelleseparation. Nutzung der Feststoffe als alternatives Gaersubstrat in Biogasanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Kroeger, Rhena; Hothan, Andreas; Theuvsen, Ludwig; Broll, Gabriele; Brauckmann, Hans-Joerg; Bronsema, Hauke [Goettingen Univ. (Germany). Dept. fuer Agraroekonomie und Rurale Entwicklung, Betriebswirtschaftslehre des Agribusiness

    2013-10-01

    The increasing regional concentration of dairy farming requires alternatives for the use of the accruing slurry to defuse the nutrient problem. One possibility is to separate the manure and use the solid fraction for an energetic use in biogas plants in nutrient undersupplied regions. First practical tests on dairy slurry separation have shown that separators are able to achieve a performance 1.3 to 16.6 tons of mass flow per hour. The nutrients are disproportionately deposited in the solid fraction. Furthermore, the solid fractions show a methane building potential that is double as high as the raw slurry methane yield. An energetic use of the solid fraction allows the reduction of other substrates. Thus, it is possible to decrease the land requirements and the costs for other substrates. (orig.)

  6. Malzeme Taşıma Sistemi Alternatiflerinin Değerlendirilmesinde Bulanık-Promethee Yaklaşımı = Evaluating Material Handling System Alternatives Using Fuzzy-Promethee Approach

    Directory of Open Access Journals (Sweden)

    Bahadır GÜLSÜN

    2011-01-01

    Full Text Available Material handling system selection process has an important effect on productivity of manufacturing systems. Considering the importance of this process, it can be seen that there is a necessity to establish a systematic approach. In this study, to determine the best material handling system alternative, PROMETHEE approach is utilized. With the aim of taking into account the vagueness in the evaluation process and obtaining decision maker evaluations in an easier way with linguistic terms, fuzzy sets are utilized. To this end, a modified version of PROMETHEE is used. To foster the better understanding of the methodology, a real life application of a manufacturer is realized.

  7. Seal design alternatives study

    International Nuclear Information System (INIS)

    This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information

  8. Seal design alternatives study

    Energy Technology Data Exchange (ETDEWEB)

    Van Sambeek, L.L. [RE/SPEC Inc., Rapid City, SD (US); Luo, D.D.; Lin, M.S.; Ostrowski, W.; Oyenuga, D. [Parsons Brinckerhoff Quade & Douglas, Inc., San Francisco, CA (US)

    1993-06-01

    This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information.

  9. Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 3: Energy conversion subsystems and components. Part 1: Bottoming cycles and materials of construction

    Science.gov (United States)

    Shah, R. P.; Solomon, H. D.

    1976-01-01

    Energy conversion subsystems and components were evaluated in terms of advanced energy conversion systems. Results of the bottoming cycles and materials of construction studies are presented and discussed.

  10. Cosmic alternatives?

    Science.gov (United States)

    Gregory, Ruth

    2009-04-01

    "Cosmologists are often in error but never in doubt." This pithy characterization by the Soviet physicist Lev Landau sums up the raison d'être of Facts and Speculations in Cosmology. Authors Jayant Narlikar and Geoffrey Burbidge are proponents of a "steady state" theory of cosmology, and they argue that the cosmological community has become fixated on a "Big Bang" dogma, suppressing alternative viewpoints. This book very much does what it says on the tin: it sets out what is known in cosmology, and puts forward the authors' point of view on an alternative to the Big Bang.

  11. Walter Russell's concepts as the basis for an alternative view on radioactivity induced oxygen-ozone depletion and food chain pollution; and as the basis for alternative fuels, materials, energy production, and radioactive waste cleanup

    International Nuclear Information System (INIS)

    The following topics with supporting data will be presented: The transmutation of atmospheric nitrogen into carbon 14 and tritium via radioactivity as a source of omnipresent food and water pollution, and the possible correlation of oxygen transmutation into carbon 14 and tritium by the same mechanisms as well as into sulfur. Walter Russell's four pole field dual polarity control as a basis for transmutation will be discussed with reference to past and contemporary results of experimentation on this basis. Extension of the concepts into free hydrogen energy fuel, nitrogen fertilizers, other materials production,and transmutation of radioactive wastes into non radioactive elements will be discussed

  12. Special Section: Complementary and Alternative Medicine (CAM): Time to Talk

    Science.gov (United States)

    ... with your health care providers any complementary and alternative medicines you take or are thinking about starting. Photo: ... and older use some form of complementary and alternative medicine (CAM). But less than one-third who use ...

  13. Alternative Agriculture

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Will the popularization of bioenergy, a new source for powering China, trigger another agricultural revolution? Skyrocketing energy prices, especially the oil shock in the first half of 2005, are pushing China to seek more substitutes for gasoline. A number of cities are turning to ethanol-blended gas made from com. Starting this month, the sale of regular gasoline will be brought to an end in nine of China's

  14. Chitosan as a starting material for wound healing applications

    OpenAIRE

    Patrulea, Viorica; Ostafe, V.; Borchard, Gerrit; Jordan, Olivier

    2015-01-01

    Chitosan and its derivatives have attracted great attention due to their properties beneficial for application to wound healing. The main focus of the present review is to summarize studies involving chitosan and its derivatives, especially N,N,N-trimethyl-chitosan (TMC), N,O-carboxymethyl-chitosan (CMC) and O-carboxymethyl-N,N,N-trimethyl-chitosan (CMTMC), used to accelerate wound healing. Moreover, formulation strategies for chitosan and its derivatives, as well as their in vitro, in vivo a...

  15. Chitosan as a starting material for wound healing applications.

    Science.gov (United States)

    Patrulea, V; Ostafe, V; Borchard, G; Jordan, O

    2015-11-01

    Chitosan and its derivatives have attracted great attention due to their properties beneficial for application to wound healing. The main focus of the present review is to summarize studies involving chitosan and its derivatives, especially N,N,N-trimethyl-chitosan (TMC), N,O-carboxymethyl-chitosan (CMC) and O-carboxymethyl-N,N,N-trimethyl-chitosan (CMTMC), used to accelerate wound healing. Moreover, formulation strategies for chitosan and its derivatives, as well as their in vitro, in vivo and clinical applications in wound healing are described. PMID:26614560

  16. (+)-Aromadendrene as chiral starting material for the synthesis of sesquiterpenes.

    NARCIS (Netherlands)

    Gijsen, H.J.M.

    1993-01-01

    One of the distillation tails of the oil of Eucalyptus globulus, which is commercially available, contains about 55-70% of (+)-aromadendrene ( 2 ), together with 10-15% of alloaromadendrene ( 3 ). In this thesis has been described how (+)-aromadendrene from Eucalypt

  17. Growing Alternatives

    DEFF Research Database (Denmark)

    Bagger-Petersen, Mai Corlin

    2014-01-01

    From 2014, Anhui Province will pilot a reform of the residential land market in China, thus integrating rural Anhui in the national housing market. In contrast, artist and activist Ou Ning has proposed the Bishan time money currency, intending to establish an alternative economic circuit in Bishan...

  18. State alternative route designations

    Energy Technology Data Exchange (ETDEWEB)

    1989-07-01

    Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select alternative routes. First,the state must establish a ``state routing agency,`` defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice of DOT of any alternative route designation before the routes are deemed effective.

  19. State alternative route designations

    Energy Technology Data Exchange (ETDEWEB)

    1989-07-01

    Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select alternative routes. First,the state must establish a state routing agency,'' defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice of DOT of any alternative route designation before the routes are deemed effective.

  20. Drug Abuse Prevention Starts with Parents

    Science.gov (United States)

    ... Stages Listen Español Text Size Email Print Share Drug Abuse Prevention Starts with Parents Page Content Article Body ... for a time when drugs may be offered. Drug abuse prevention starts with parents learning how to talk ...

  1. Tingzikou key water control project started construction

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Tingzikou key water control project on Jialing River, one of 18 newly started key projects in 2009 for China's western part development program, formally started construction at the end of November last year.

  2. Process parameters for high-quality on-contour starting of laser cutting of steel

    NARCIS (Netherlands)

    Meijer, C.Z.; Meijer, J.; Bakkers, E.P.M.

    1997-01-01

    Laser cut initiation in full material usually results in a start hole with bad quality. Starting strategies have been developed to avoid these crater-like holes. Start areas were obtained showing almost the same quality as the rest of the cut. As a result of the experiments and literature research t

  3. Engine management during NTRE start up

    Science.gov (United States)

    Bulman, Mel; Saltzman, Dave

    1993-01-01

    The topics are presented in viewgraph form and include the following: total engine system management critical to successful nuclear thermal rocket engine (NTRE) start up; NERVA type engine start windows; reactor power control; heterogeneous reactor cooling; propellant feed system dynamics; integrated NTRE start sequence; moderator cooling loop and efficient NTRE starting; analytical simulation and low risk engine development; accurate simulation through dynamic coupling of physical processes; and integrated NTRE and mission performance.

  4. MPI-Start and MPI-Utils

    OpenAIRE

    Fernández-del-Castillo, Enol

    2013-01-01

    mpi-start is a set of scripts to close the gap between the workload management system of a Grid insfrastructure and the configuration of the nodes on which MPI applications are run. The package is used to help the user to start MPI applications on heterogeneous Grid sites. mpi-start provides an abstraction layer that offers a unique interface to start parallel jobs with different execution environments implementations. It supports several different MPI implementations under different ba...

  5. An Alternative Corrosion Resistance Test Method for Solar Cells and Interconnection Materials Limiting the Number of Long-lasting and Expensive Damp-Heat Climate Chamber Tests

    Energy Technology Data Exchange (ETDEWEB)

    Van Aken, B.B.; Gouwen, R.J.; Veldman, D.; Bende, E.E.; Eerenstein, W. [ECN Solar Energy, Petten (Netherlands)

    2013-06-15

    Damp-heat testing of PV modules is a time-consuming process, taking months. We present an alternative test method: electrochemical noise (EcN) measurements. Data acquisition times vary between minutes for direct exposure to several tens of hours for encapsulated samples. EcN measurements are presented for several solar cell concepts and different environments. We have found that the degradation in damp-heat testing is proportional to the electrochemical noise signal. In conclusion, the electrochemical noise measurements are a fast, versatile tool to test the corrosion resistance of solar cells, which can be tested for different environments including encapsulation.

  6. Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 2: Materials considerations. [materials used in boilers and heat exchangers of energy conversion systems for electric power plants using coal

    Science.gov (United States)

    Thomas, D. E.

    1976-01-01

    Extensive studies are presented which were carried out on materials behavior in nine advanced energy conversion systems employing coal and coal-derived fuels. The areas of materials behavior receiving particular attention in this regard are: (1) fireside corrosion and erosion in boiler and heat exchanger materials, (2) oxidation and hot corrosion of gas turbine materials, (3) liquid metal corrosion and mass transport, (4) high temperature steam corrosion, (5) compatability of materials with coal slag and MHD seed, (6) reaction of materials with impure helium, (7) allowable stresses for boiler and heat exchanger materials, (8) environmental effects on mechanical properties, and (9) liquid metal purity control and instrumentation. Such information was then utilized in recommending materials for use in the critical components of the power systems, and at the same time to identify materials problem areas and to evaluate qualitatively the difficulty of solving those problems. Specific materials recommendations for critical components of the nine advanced systems under study are contained in summary tables.

  7. Summary report of the screening process to determine reasonable alternatives for long-term storage and disposition of weapons-usable fissile materials

    International Nuclear Information System (INIS)

    Significant quantities of weapons-usable fissile materials (primarily plutonium and highly enriched uranium) have become surplus to national defense needs both in the US and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety and health consequences if surplus fissile materials are not properly managed. As announced in the Notice of Intent (NOI) to prepare a Programmatic Environmental Impact Statement (PEIS), the Department of Energy is currently conducting an evaluation process for disposition of surplus weapons-usable fissile materials determined surplus to National Security needs, and long-term storage of national security and programmatic inventories, and surplus weapons-usable fissile materials that are not able to go directly from interim storage to disposition. An extensive set of long-term storage and disposition options was compiled. Five broad long-term storage options were identified; thirty-seven options were considered for plutonium disposition; nine options were considered for HEU disposition; and eight options were identified for Uranium-233 disposition. Section 2 discusses the criteria used in the screening process. Section 3 describes the options considered, and Section 4 provides a detailed summary discussions of the screening results

  8. Summary report of the screening process to determine reasonable alternatives for long-term storage and disposition of weapons-usable fissile materials

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-29

    Significant quantities of weapons-usable fissile materials (primarily plutonium and highly enriched uranium) have become surplus to national defense needs both in the US and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety and health consequences if surplus fissile materials are not properly managed. As announced in the Notice of Intent (NOI) to prepare a Programmatic Environmental Impact Statement (PEIS), the Department of Energy is currently conducting an evaluation process for disposition of surplus weapons-usable fissile materials determined surplus to National Security needs, and long-term storage of national security and programmatic inventories, and surplus weapons-usable fissile materials that are not able to go directly from interim storage to disposition. An extensive set of long-term storage and disposition options was compiled. Five broad long-term storage options were identified; thirty-seven options were considered for plutonium disposition; nine options were considered for HEU disposition; and eight options were identified for Uranium-233 disposition. Section 2 discusses the criteria used in the screening process. Section 3 describes the options considered, and Section 4 provides a detailed summary discussions of the screening results.

  9. Synthesis and characterization of alternating poly(amide urethane)s

    OpenAIRE

    Sharma, Bhaskar

    2004-01-01

    This thesis deals with the preparation of alternating poly(amide urethane)s which might be of interest for the manufacture of powder coatings. The synthesis of poly(amide urethane)s was performed in environmentally friendly way without using isocyanates or phosgene. The starting materials for the synthesis were e-caprolactam, e-caprolactone, amino alcohols, diamines and carbonic acid derivatives, i.e. diphenyl carbonate and ethylene carbonate as substitutes for phosgene. A new synthesis was d...

  10. Layout decomposition and synthesis for a modular technology to solve the edge-placement challenges by combining selective etching, direct stitching, and alternating-material self-aligned multiple patterning processes

    Science.gov (United States)

    Liu, Hongyi; Han, Ting; Zhou, Jun; Chen, Yijian

    2016-03-01

    To overcome the prohibitive barriers of edge-placement errors (EPE) in the cut/block/via step of complementary lithography, we propose a modular patterning approach by combining layout stitching, selective etching, and alternating-material self-aligned multiple patterning (altSAMP) processes. In this patterning approach, altSAMP is used to create line arrays with two materials alternatively which allow a highly selective etching process to remove one material without attacking the other, therefore more significant EPE effect can be tolerated in line-cutting step. With no need of connecting vias, the stitching process can form 2-D features by directly stitching two components of patterns together to create 2-D design freedom as well as multiple-CD/pitch capability. By adopting this novel approach, we can potentially achieve higher processing yield and more 2-D design freedom for continuous IC scaling down to 5 nm. We developed layout decomposition and synthesis algorithms for critical layers, and the fin/gate/metal layer from NSCU open cell library is used to test the proposed algorithms.

  11. A Computational Study on the Use of an Aluminium Metal Matrix Composite and Aramid as Alternative Brake Disc and Brake Pad Material

    Directory of Open Access Journals (Sweden)

    Nosa Idusuyi

    2014-01-01

    Full Text Available A computational model for the heat generation and dissipation in a disk brake during braking and the following release period has been formulated. The model simulates the braking action by investigating the thermal behaviour occurring on the disc and pad surfaces during this period. A comparative study was made between grey cast iron (GCI, asbestos, Aluminium metal matrix composite (AMC, and aramid as brake pad and disc materials. The braking process and following release period were simulated for four material combinations, GCI disc and Asbestos pad, GCI disc and Aramid pad, AMC disc and Asbestos pad, AMC disc and Aramid pad using COMSOL Multiphysics software. The results show similarity in thermal behaviour at the contact surface for the asbestos and aramid brake pad materials with a temperature difference of 1.8 K after 10 seconds. For the brake disc materials, the thermal behaviour was close, with the highest temperature difference being 9.6 K. The GCI had a peak temperature of 489 K at 1.2 seconds and AMC was 465.5 K but cooling to 406.4 K at 10 seconds, while the GCI was 394.7 K.

  12. GROWING ALTERNATIVE SUSTAINABLE BUILDINGS: BIO-COMPOSITE PRODUCTS FROM NATURAL FIBER, BIODEGRADABLE AND RECYCLABLE POLYMER MATERIALS FOR LOAD-BEARING CONSTRUCTION COMPONENTS

    Science.gov (United States)

    The project is an integrative educational and research project that will revolutionize design and construction methods towards more sustainable buildings. The project will develop and test new product design concepts using bio-composite materials in load-bearing and fa&cced...

  13. Alternative crops

    International Nuclear Information System (INIS)

    Surplus cereal production in the EEC and decreasing product prices, mainly for cereals, has prompted considerable interest for new earnings in arable farming. The objective was to examine whether suggested new crops (fibre, oil, medicinal and alternative grains crops) could be considered as real alternatives. Whether a specific crop can compete economically with cereals and whether there is a market demand for the crop is analyzed. The described possibilities will result in ca. 50,000 hectares of new crops. It is expected that they would not immediately provide increased earnings, but in the long run expected price developments are more positive than for cereals. The area for new crops will not solve the current surplus cereal problem as the area used for new crops is only 3% of that used for cereals. Preconditions for many new crops is further research activities and development work as well as the establishment of processing units and organizational initiatives. Presumably, it is stated, there will then be a basis for a profitable production of new crops for some farmers. (AB) (47 refs.)

  14. Supplementary examination of alternative materials in a model steam generator: Volume 3, tube characterization by metallography and transmission electron microscopy: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Krupowicz, J.J.; Stubbins, J.F.; Mehler, M.

    1988-10-01

    The microstructural characteristics of current and candidate alloys for steam generator heat transfer tubing were determined utilizing a variety of techniques. Mill annealed heats of Alloys 690 and 800NG were examined as well as heats of Alloy 600 in the mill annealed, process stabilized, sensitized and thermally treated conditions. Characterization included optical microscopy, transmission electron microscopy and scanning transmission electron microscopy of these materials in their pre- and post-test conditions (i.e., archive and exposure for 11,328 hours to 621/degree/F primary temperature). The results were utilized to elicit comparisons of these materials to stress corrosion cracking resistance in sulfate faulted secondary environments. 83 figs., 8 tabs.

  15. Avaliação de materiais alternativos em substituição à maravalha como cama de aviário Alternative material to replace wood shavings as broiler litter

    Directory of Open Access Journals (Sweden)

    Valdir Silveira de Avila

    2008-02-01

    Full Text Available Com o objetivo de testar materiais alternativos para cama de aviário na criação de frangos de corte, foram alojados seis lotes consecutivos, cada um contendo 5.600 aves, apenas fêmeas, distribuídas em 35 boxes. Os tratamentos consistiram de sete tipos de material para cama (maravalha; casca de arroz; sabugo de milho triturado; capim-cameron picado; palhada de soja picada; resto da cultura do milho picado; e serragem, cada um com cinco repetições. Avaliaram-se nas aves o peso corporal médio e o consumo médio de ração e, nas camas, os teores de N, Ca, P e pH. Observaram-se ainda a presença de salmonela, a contagem de oocistos de eimeria na cama e o escore de lesões no intestino das aves ao abate. A utilização dos materiais alternativos avaliados como cama de aviário, por seis lotes consecutivos, como alternativas à maravalha não prejudicou o desempenho de frangos de corte. Esses materiais, após o descarte, por apresentarem valor em minerais superior ao da maravalha, podem ser utilizados na adubação de culturas.Aiming to evaluate alternative materials to be used as broiler litter reutilization, six consecutive lots of 5,600 female broilers were allocated to 35 pens. The treatments consisted of seven types of litter materials: wood shavings, rice husk, ground corncob, chopped camerongrass, chopped soybean straw, chopped corn stalk and sawdust, each one with five replications. In the birds, it was evaluated the average body weight, feed consumption and in the litter, it was evaluated the contents of N, Ca, P and pH. The presence of salmoella, the eimeria oocists counting in the litter, and the gut birds lesions score at slaughter were also observed. The use of alternative materials evaluated as litter, per six concecutive lots, as a alternative for wood shavings did no prejudice the performance of broilers. These materials, by presenting mineral values higher than wood shavings, after discarding, could be used as culture

  16. From START to NEW START. The dilemma and future of nuclear disarmament; Von START zu NEW START. Das Dilemma und die Zukunft der Nuklearen Abruestung

    Energy Technology Data Exchange (ETDEWEB)

    Plettenberg, Lars

    2012-07-01

    The report describes the existing four agreements on nuclear disarmament: START I (1991). START II (1993), SORT (2002) and NEW START (2010). The chapter on the dependence between nuclear disarmament and strategic stability covers the issues mutual assured destruction (MAD), credibility, overkill capacity; the role of nuclear weapons in the national strategies of the USA and NATO, Russia, Great Britain, France, China and the other nuclear states. Ways out of MAD include disarmament, de-alerting and mutual assured protection (MAP).

  17. Raw materials, energy, water. Air pollution, ecological nutrition, alternatives to nuclear energy; Rohstoffe, Energie, Wasser. Luftverschmutzung, oekologische Ernaehrung, Alternativen zur Atomkraft

    Energy Technology Data Exchange (ETDEWEB)

    Lepper, Rolf (comp.)

    2008-07-01

    ''Ecological cattle breeding: A climate killer''. This was the title of an article in ''Frankfurter Rundschau'' journal, which summarized the findings of a study according to which ecological cattle breeding is more harmful to the environment than conventional cattle breeding, not least because eco-cattle live longer and are kept according to the principles of organic farming. This special issue of OeKO-TEST goes into detail about ecological nutrition. After all, animal farming accounts for 18 percent of the global climate-relevant gaseous emissions. A closer look will show that ecological cattle breeding is not a climate killer but that ecological farming and nutrition may even help in the fight against global climate change. In fact, this has been known all along, as are other strategies to prevent global warming. Thirty years ago, the Oeko-Institut, Freiburg, published a concept to prevent global climate change that is still up to date. It comprises energy conservation, rational energy use, and the utilization of alternative energy sources. If these concepts had been followed then and there, we would not have the problems of global climate change and rising energy cost today. We all know how to save this planet and how to prevent the dying out of species, the pollution of the oceans and air, and the destruction of forests. It is up to us to do it. (orig.)

  18. Alternative Energies

    Energy Technology Data Exchange (ETDEWEB)

    Planting, A.; De saint Jacob, Y.; Verwijs, H.; Belin, H.; Preesman, L.

    2009-03-15

    In two articles, one interview and one column attention is paid to alternative energies. The article 'A new light on saving energy' discusses the option to save energy by modernising lighting systems in urban areas. The column 'View from Paris' focuses on investment decisions in France with regard to renewable energy and energy savings. The article 'Europe turns a blind eye to big battery' discusses developments in batteries to store energy. The interview concerns fuel cell expert and formerly President of UTC Power Jan van Dokkum. The last article gives a brief overview of the European Energy Research Alliance (EERA) and the challenges this alliance will have to face with regard to climate change and energy security.

  19. Energy alternatives

    International Nuclear Information System (INIS)

    English. A special committe of the Canadian House of Commons was established on 23 May 1980 to investigate the use of alternative energy sources such as 'gasohol', liquified coal, solar energy, methanol, wind and tidal power, biomass, and propane. In its final report, the committee envisions an energy system for Canada based on hydrogen and electricity, using solar and geothermal energy for low-grade heat. The committe was not able to say which method of generating electricty would dominate in the next century, although it recommends that fossil fuels should not be used. The fission process is not specifically discussed, but the outlook for fusion was investigated, and continued governmental support of fusion research is recommended. The report proposes some improvements in governmental energy organizations and programs

  20. Iodine confinement into metal-organic frameworks (MOFs)-low temperature sintering glasses to form novel glass composite material (GCM) alternative waste forms.

    Energy Technology Data Exchange (ETDEWEB)

    Nenoff, Tina Maria; Garino, Terry J.; Sava, Dorina Florentina

    2010-11-01

    The safe handling of reprocessed fuel addresses several scientific goals, especially when considering the capture and long-term storage of volatile radionuclides that are necessary during this process. Despite not being a major component of the off-gas, radioiodine (I{sub 2}) is particularly challenging, because it is a highly mobile gas and {sup 129}I is a long-lived radionuclide (1.57 x 10{sup 7} years). Therefore, its capture and sequestration is of great interest on a societal level. Herein, we explore novel routes toward the effective capture and storage of iodine. In particular, we report on the novel use of a new class of porous solid-state functional materials (metal-organic frameworks, MOFs), as high-capacity adsorbents of molecular iodine. We further describe the formation of novel glass-composite material (GCM) waste forms from the mixing and sintering of the I{sub 2}-containing MOFs with Bi-Zn-O low-temperature sintering glasses and silver metal flakes. Our findings indicate that, upon sintering, a uniform monolith is formed, with no evidence of iodine loss; iodine is sequestered during the heating process by the in situ formation of AgI. Detailed materials characterization analysis is presented for the GCMs. This includes powder X-ray diffraction, scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), thermal analysis (thermogravimetric analysis (TGA)), and chemical durability tests including aqueous leach studies (product consistency test (PCT)), with X-ray fluorescence (XRF) and inductively coupled plasma-mass spectrometry (ICP-MS) of the PCT leachate.

  1. Iodine confinement into metal-organic frameworks (MOFs): Low temperature sintering glasses to form novel glass composite material (GCM) alternative waste forms

    International Nuclear Information System (INIS)

    The safe handling of reprocessed fuel addresses several scientific goals, especially when considering the capture and long-term storage of volatile radionuclides that are necessary during this process. Despite not being a major component of the off-gas, radioiodine (I2) is particularly challenging, because it is a highly mobile gas and 129I is a long-lived radionuclide (1.57 x 107 years). Therefore, its capture and sequestration is of great interest on a societal level. Herein, we explore novel routes toward the effective capture and storage of iodine. In particular, we report on the novel use of a new class of porous solid-state functional materials (metal-organic frameworks, MOFs), as high-capacity adsorbents of molecular iodine. We further describe the formation of novel glass-composite material (GCM) waste forms from the mixing and sintering of the I2-containing MOFs with Bi-Zn-O low-temperature sintering glasses and silver metal flakes. Our findings indicate that, upon sintering, a uniform monolith is formed, with no evidence of iodine loss; iodine is sequestered during the heating process by the in situ formation of AgI. Detailed materials characterization analysis is presented for the GCMs. This includes powder X-ray diffraction, scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), thermal analysis (thermogravimetric analysis (TGA)), and chemical durability tests including aqueous leach studies (product consistency test (PCT)), with X-ray fluorescence (XRF) and inductively coupled plasma-mass spectrometry (ICP-MS) of the PCT leachate.

  2. Black Afrikaans: An alternative use

    Directory of Open Access Journals (Sweden)

    Anna P. Maritz

    2016-09-01

    Full Text Available This article provides a first look at the nature of the alternative functions of Black Afrikaans. These functions realise when Black Afrikaans is imitated by Afrikaans mother-tongue speakers. The functions of the alternative use of Black Afrikaans centre on: the social nature of the variety, sensitivity as a deciding role-player, identity, humour, inclusivity and exclusivity, language repertoire and similar variety. Furthermore, because of the direct relationship between Black Afrikaans, Pidginised Afrikaans and the imitation of Black Afrikaans, these varieties are compared to establish a starting point description for the imitation of Black Afrikaans, as the variety has not yet been described.

  3. A novel induction motor starting method using superconduction

    Science.gov (United States)

    Silva, F. B. B.; Orlando, M. T. D.; Fardin, J. F.; Simonetti, D. S.; Baldan, C. A.

    2014-12-01

    In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method.

  4. Line start permanent magnet synchronous motors: Challenges and opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Hassanpour Isfahani, Arash; Vaez-Zadeh, Sadegh [School of Electrical and Computer Engineering, Faculty of Engineering, University of Tehran, North Kargar Ave., P.O. Box: 14395/515, Tehran (Iran)

    2009-11-15

    Future energy challenges, likewise the environmental crises such as fossil fuel emissions and global warming urge the world to focus on energy saving programs more than ever. An effective way to face these challenges is to improve electric motors efficiency as one of the greatest energy consumption apparatuses in the world. Induction motors constitute, by far, the largest portion of electric motors both in terms of quantity and total power ratings among all electric motors. However, more efficient motor types gradually appear as alternatives. In this paper, line start permanent magnet motors as a powerful candidate with growing market are investigated in some details. The motor opportunities like high efficiency, high power factor and high power density are explored against the challenges associated with this motor including higher cost, extra manufacturing burden and transient and synchronization behaviors. Finally, some concluding comments and remarks are drawn for future research and manufacturing of line start permanent magnet motors. (author)

  5. A paradigm shift in patterning foundation from frequency multiplication to edge-placement accuracy: a novel processing solution by selective etching and alternating-material self-aligned multiple patterning

    Science.gov (United States)

    Han, Ting; Liu, Hongyi; Chen, Yijian

    2016-03-01

    Overlay errors, cut/block and line/space critical-dimension (CD) variations are the major sources of the edge-placement errors (EPE) in the cut/block patterning processes of complementary lithography when IC technology is scaled down to sub-10nm half pitch (HP). In this paper, we propose and discuss a modular technology to reduce the EPE effect by combining selective etching and alternating-material (dual-material) self-aligned multiple patterning (altSAMP) processes. Preliminary results of altSAMP process development and material screening experiment are reported and possible material candidates are suggested. A geometrical cut-process yield model considering the joint effect of overlay errors, cut-hole and line CD variations is developed to analyze its patterning performance. In addition to the contributions from the above three process variations, the impacts of key control parameters (such as cut-hole overhang and etching selectivity) on the patterning yield are examined. It is shown that the optimized altSAMP patterning process significantly improves the patterning yield compared with conventional SAMP processes, especially when the half pitch of device patterns is driven down to 7 nm and below.

  6. When Do Start-Ups Make Sense?

    Science.gov (United States)

    Langemeyer, Clement J.

    2005-01-01

    The start-up has received considerable attention in the last few years. While the National Research Council of Canada has generated many start-ups over its 88-year history, the creation of a formal entrepreneurship programme in the mid-1990s dramatically accelerated the pace at which they were created. Many factors come into play in the decision…

  7. Lean and global technology start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik;

    2015-01-01

    In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being g...

  8. Getting started with SBT for Scala

    CERN Document Server

    Saxena, Shiti

    2013-01-01

    A practical and fast-paced guide, Getting Started with SBT for Scala walks you through the setup of Scala projects in SBT with sample code for common as well as critical scenarios.Getting Started with SBT for Scala is for developers working on Scala projects who are interested in learning and utilizing Simple Build Tool to manage the build process.

  9. Application of SMES Unit in Black Start

    Science.gov (United States)

    Yang, Jun; Liu, Wenqing; Liu, Pei

    Blackout of large area is a serious threat to modern power system, so power system restoration which is called Black Start is a critical task for reducing economic losses and social unrest caused by blackout. Traditiona black start sometimes may suffer from inflexible black start units and overvoltage and serious oscillation. As a power storage unit, SMES has the ability of fast exchanging active and reactive power with power grid in all four quadrants, so it is proposed as a new solution to improve the black start process in this paper. Comparing to traditional black start, some unique advantages of SMES for black start are presented. Also SMES model and related control strategy are introduced in detail. A simulation model is established based on PSCAD/EMTDC to investigate the validity and flexibility of SMES in black start. Simulation results show that SMES unit can bring thermal generators online, and it has better performance on overvoltage restraint and amping oscillation than traditional black start. Also, the performance of nonlinear PID-controlled SMES is better than that of PID-controlled SMES.

  10. Networks of recyclable material waste-picker’s cooperatives: An alternative for the solid waste management in the city of Rio de Janeiro

    Energy Technology Data Exchange (ETDEWEB)

    Tirado-Soto, Magda Martina, E-mail: magda@pep.ufrj.br [Program of Production Engineering, School and Research in Engineering, Federal University of Rio de Janeiro (Brazil); Zamberlan, Fabio Luiz, E-mail: fabio@pep.ufrj.br [Program of Production Engineering, School and Research in Engineering, Federal University of Rio de Janeiro (Brazil)

    2013-04-15

    Highlights: ► In the marketing of recyclable materials, the waste-pickers are the least wins. ► It is proposed creating a network of recycling cooperatives to achieve viability. ► The waste-pickers contribute to waste management to the city. - Abstract: The objective of this study is to discuss the role of networks formed of waste-picker cooperatives in ameliorating problems of final disposal of solid waste in the city of Rio de Janeiro, since the city’s main landfill will soon have to close because of exhausted capacity. However, it is estimated that in the city of Rio de Janeiro there are around five thousand waste-pickers working in poor conditions, with lack of physical infrastructure and training, but contributing significantly by diverting solid waste from landfills. According to the Sustainable Development Indicators (IBGE, 2010a,b) in Brazil, recycling rates hover between 45% and 55%. In the municipality of Rio de Janeiro, only 1% of the waste produced is collected selectively by the government (COMLURB, 2010), demonstrating that recycling is mainly performed by waste-pickers. Furthermore, since the recycling market is an oligopsony that requires economies of scale to negotiate directly with industries, the idea of working in networks of cooperatives meets the demands for joint marketing of recyclable materials. Thus, this work presents a method for creating and structuring a network of recycling cooperatives, with prior training for working in networks, so that the expected synergies and joint efforts can lead to concrete results. We intend to demonstrate that it is first essential to strengthen the waste-pickers’ cooperatives in terms of infrastructure, governance and training so that solid waste management can be environmentally, socially and economically sustainable in the city of Rio de Janeiro.

  11. Networks of recyclable material waste-picker’s cooperatives: An alternative for the solid waste management in the city of Rio de Janeiro

    International Nuclear Information System (INIS)

    Highlights: ► In the marketing of recyclable materials, the waste-pickers are the least wins. ► It is proposed creating a network of recycling cooperatives to achieve viability. ► The waste-pickers contribute to waste management to the city. - Abstract: The objective of this study is to discuss the role of networks formed of waste-picker cooperatives in ameliorating problems of final disposal of solid waste in the city of Rio de Janeiro, since the city’s main landfill will soon have to close because of exhausted capacity. However, it is estimated that in the city of Rio de Janeiro there are around five thousand waste-pickers working in poor conditions, with lack of physical infrastructure and training, but contributing significantly by diverting solid waste from landfills. According to the Sustainable Development Indicators (IBGE, 2010a,b) in Brazil, recycling rates hover between 45% and 55%. In the municipality of Rio de Janeiro, only 1% of the waste produced is collected selectively by the government (COMLURB, 2010), demonstrating that recycling is mainly performed by waste-pickers. Furthermore, since the recycling market is an oligopsony that requires economies of scale to negotiate directly with industries, the idea of working in networks of cooperatives meets the demands for joint marketing of recyclable materials. Thus, this work presents a method for creating and structuring a network of recycling cooperatives, with prior training for working in networks, so that the expected synergies and joint efforts can lead to concrete results. We intend to demonstrate that it is first essential to strengthen the waste-pickers’ cooperatives in terms of infrastructure, governance and training so that solid waste management can be environmentally, socially and economically sustainable in the city of Rio de Janeiro

  12. START Analysis for ESAS Capability Needs Prioritization

    Science.gov (United States)

    Lincoln, William; Mrozinski, Joe; Hua, Hook; Merida, Sofia; Shelton, Kacie; Adumitroaie, Virgil; Weisbin, Charles R.; Derleth, Jason

    2006-01-01

    START is a tool to optimize research and development primarily for NASA missions. It was developed within the Strategic Systems Technology Program Office, a division of the Office of the Chief Technologist at NASA's Jet Propulsion Laboratory. START is capable of quantifying and comparing the risks, costs, and potential returns of technologies that are candidates for funding. START can be enormously helpful both in selecting technologies for development -- within the constraints of budget, schedule, and other resources -- and in monitoring their progress. START's methods are applicable to everything from individual tasks to multiple projects comprising entire programs of investigation. They can address virtually any technology assessment and capability prioritization issue. In this report, START is used to analyze the capability needs using data from NASA's Exploration Systems Architecture Study (ESAS).

  13. Nanocrystalline ceramic materials

    Science.gov (United States)

    Siegel, R.W.; Nieman, G.W.; Weertman, J.R.

    1994-06-14

    A method is disclosed for preparing a treated nanocrystalline metallic material. The method of preparation includes providing a starting nanocrystalline metallic material with a grain size less than about 35 nm, compacting the starting nanocrystalline metallic material in an inert atmosphere and annealing the compacted metallic material at a temperature less than about one-half the melting point of the metallic material. 19 figs.

  14. Use of alternative carrier materials in AOAC Official Method 2008.05, efficacy of liquid sporicides against spores of Bacillus subtilis on a hard, nonporous surface, quantitative three-step method.

    Science.gov (United States)

    Tomasino, Stephen F; Rastogi, Vipin K; Wallace, Lalena; Smith, Lisa S; Hamilton, Martin A; Pines, Rebecca M

    2010-01-01

    The quantitative Three-Step Method (TSM) for testing the efficacy of liquid sporicides against spores of Bacillus subtilis on a hard, nonporous surface (glass) was adopted as AOAC Official Method 2008.05 in May 2008. The TSM uses 5 x 5 x 1 mm coupons (carriers) upon which spores have been inoculated and which are introduced into liquid sporicidal agent contained in a microcentrifuge tube. Following exposure of inoculated carriers and neutralization, spores are removed from carriers in three fractions (gentle washing, fraction A; sonication, fraction B; and gentle agitation, fraction C). Liquid from each fraction is serially diluted and plated on a recovery medium for spore enumeration. The counts are summed over the three fractions to provide the density (viable spores per carrier), which is log10-transformed to arrive at the log density. The log reduction is calculated by subtracting the mean log density for treated carriers from the mean log density for control carriers. This paper presents a single-laboratory investigation conducted to evaluate the applicability of using two porous carrier materials (ceramic tile and untreated pine wood) and one alternative nonporous material (stainless steel). Glass carriers were included in the study as the reference material. Inoculated carriers were evaluated against three commercially available liquid sporicides (sodium hypochlorite, a combination of peracetic acid and hydrogen peroxide, and glutaraldehyde), each at two levels of presumed efficacy (medium and high) to provide data for assessing the responsiveness of the TSM. Three coupons of each material were evaluated across three replications at each level; three replications of a control were required. Even though all carriers were inoculated with approximately the same number of spores, the observed counts of recovered spores were consistently higher for the nonporous carriers. For control carriers, the mean log densities for the four materials ranged from 6.63 for

  15. Prepsolv (TM): The optimum alternative to 1,1,1-trichloroethane and methyl ethyl ketone for hand-wipe cleaning of aerospace materials

    Science.gov (United States)

    Gallagher, R. Scott; Purvis, John A.; Moran, Wade W.

    1995-01-01

    Engineers at Hercules Aerospace, a rocket motor manufacturer in Utah, have worked closely with chemists at Glidco Organics to study the feasibility of using terpenes for zero-residue wipe cleaning. The result of this work is a technological breakthrough, in which the barrier to ultra-low non-volatile residue formation has been broken. After 2 years of development and testing, SCM Glidco Organics has announced the availability of Glidsafe(registered trademark) Prepsolv(TM): a state-of-the-art ultra-low residue terpene wipe cleaning agent that does not require rinsing. Prepsolv(TM) can successfully be used in simple hand-wipe cleaning processes without fear of leaving surface residues. Industry testing has confirmed that Prepsolv(TM) is not only highly effective, but can even be less expensive to use than traditional cleaning solvents like methyl chloroform. This paper addresses the features and benefits of Prepsolv(TM), and presents performance and material compatibility data that characterizes this unique cleaning agent. Since its commercialization, Hercules Aerospace has chosen Prepsolv(TM) as the optimum cleaning agent to replace ozone-depleting solvents in their weapons factory in Magna, UT. Likewise, Boeing has approved Prepsolv(TM) for cleaning components in the manufacture of commercial aircraft at their facilities in Seattle, WA and Wichita, KS. Additional approvals are forthcoming for this uniquely safe and effective solvent.

  16. Start 2: Thinking one move ahead

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.L.

    1991-11-01

    At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush`s historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R&D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

  17. Start 2: Thinking one move ahead

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.L.

    1991-11-01

    At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush's historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

  18. Start up -yritysten taloudellisen selviytymisen ennustaminen

    OpenAIRE

    Holmberg, Anna; Önder, Elif

    2015-01-01

    Tämän opinnäytetyön tarkoituksena on tutkia toimeksiantajan toiveesta suomalaisten start up –yritysten taloudellisia selviytymisedellytyksiä. Toimeksiantaja on suomalainen finanssialan yritys-konserni, jonka yhtenä liiketoimintana on rahoittaa menestyspotentiaalin omaavia start up –yrityksiä. Opinnäytetyön tulosten avulla on tavoitteena kehittää toimeksiantajan jo olemassa ole-vaa sijoitustyökalua helpottamalla start up -yritysten selviytymisen ennustamista ja tulevaisuudessa sijoituspäätöksi...

  19. Starting Circuit For Erasable Programmable Logic Device

    Science.gov (United States)

    Cole, Steven W.

    1990-01-01

    Voltage regulator bypassed to supply starting current. Starting or "pullup" circuit supplies large inrush of current required by erasable programmable logic device (EPLD) while being turned on. Operates only during such intervals of high demand for current and has little effect any other time. Performs needed bypass, acting as current-dependent shunt connecting battery or other source of power more nearly directly to EPLD. Input capacitor of regulator removed when starting circuit installed, reducing probability of damage to transistor in event of short circuit in or across load.

  20. CORPORATE BRAND BUILDING IN START-UPS

    OpenAIRE

    PETER WITT; VERENA RODE

    2005-01-01

    In this paper, we develop a multi-stage formative measurement model to investigate which factors constitute the corporate brand of a start-up as seen from within the firm (corporate identity) and as perceived from outside (corporate image). Furthermore, we propose a structural model for brand building in start-ups, i.e. the causal relation between corporate identity and corporate image. We test this model empirically for a sample of 311 German start-ups. The study proves the importance of wel...

  1. Alternative Splice in Alternative Lice.

    Science.gov (United States)

    Tovar-Corona, Jaime M; Castillo-Morales, Atahualpa; Chen, Lu; Olds, Brett P; Clark, John M; Reynolds, Stuart E; Pittendrigh, Barry R; Feil, Edward J; Urrutia, Araxi O

    2015-10-01

    Genomic and transcriptomics analyses have revealed human head and body lice to be almost genetically identical; although con-specific, they nevertheless occupy distinct ecological niches and have differing feeding patterns. Most importantly, while head lice are not known to be vector competent, body lice can transmit three serious bacterial diseases; epidemictyphus, trench fever, and relapsing fever. In order to gain insights into the molecular bases for these differences, we analyzed alternative splicing (AS) using next-generation sequencing data for one strain of head lice and one strain of body lice. We identified a total of 3,598 AS events which were head or body lice specific. Exon skipping AS events were overrepresented among both head and body lice, whereas intron retention events were underrepresented in both. However, both the enrichment of exon skipping and the underrepresentation of intron retention are significantly stronger in body lice compared with head lice. Genes containing body louse-specific AS events were found to be significantly enriched for functions associated with development of the nervous system, salivary gland, trachea, and ovarian follicle cells, as well as regulation of transcription. In contrast, no functional categories were overrepresented among genes with head louse-specific AS events. Together, our results constitute the first evidence for transcript pool differences in head and body lice, providing insights into molecular adaptations that enabled human lice to adapt to clothing, and representing a powerful illustration of the pivotal role AS can play in functional adaptation. PMID:26169943

  2. National Head Start Association Position Paper: A Vision for Head Start and State Collaboration.

    Science.gov (United States)

    Ryan, Joel; Allen, Ben

    Based on the view that coordinated efforts among Head Start programs, child care programs and other prekindergarten programs, and states can be enhanced without devolving Head Start and its high quality standards to the states, this position paper draws on a Bush Administration report and the Head Start Program Performance Standards to demonstrate…

  3. Corporate leadership and start-up entrepreneurship

    OpenAIRE

    Coulson-Thomas, Colin

    2016-01-01

    This article is based on a paper prepared by Colin Coulson-Thomas for the 2016 Dubai Global Convention on Leadership for Business Excellence. It examines the role of leadership in relation to start-up enterprises.

  4. Quit Smoking: 5 Steps to START

    Science.gov (United States)

    ... this page please turn Javascript on. Feature: Quit Smoking 5 Steps to START Past Issues / Winter 2011 ... a part of every successful plan to quit smoking: S et a quit date. T ell family, friends, ...

  5. Head Start Program Information Report (HSPIR)

    Data.gov (United States)

    U.S. Department of Health & Human Services — Information about children enrolled in the Head Start program and information about their families. Data about the children include: age, type of program attended,...

  6. Start small and build toward business intelligence.

    Science.gov (United States)

    Kirby, Sean; Robertson, Brian

    2009-01-01

    To use business intelligence effectively, healthcare organizations should start small, align organizationally, and leverage success. Organizations should determine which measures they need and how to present them. Organizations should reinvest savings to continually improve.

  7. The educational effects of school start times

    OpenAIRE

    Shapiro, Teny Maghakian

    2015-01-01

    The combination of changing sleep patterns in adolescence and early school start times leaves secondary school classrooms filled with sleep-deprived students. Evidence is growing that having adolescents start school later in the morning improves grades and emotional well-being, and even reduces car accidents. Opponents cite costly adjustments to bussing schedules and decreased time after school for jobs, sports, or other activities as reasons to retain the status quo. While changing school st...

  8. COLLEGE STUDENTS' STARTING THEIR OWN UNDERTAKINGS

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    正Nowadays there are many college students who choose to start their own undertakings instead of finding a job after graduation.The government encourages this practice,and provides many preferential policies and facilitation measures for college students.This phenomenon has aroused great concern from the whole society. However,why do so many college students take the way of starting their own

  9. Multi-wall carbon nanotubes/epoxy resin composites characterization of the starting materials and evaluation of thermal and electrical conductivity;Compositos resina epoxi/nanotubos de carbonos de paredes multiplas: caracterizacao dos materiais de partida e avaliacao das condutividades eletrica e termica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Wellington Marcos da

    2009-07-01

    In this study we investigate the electrical and thermal properties of I) composite materials fabricated with O, I, 0,5 and I wt% of concentric multi-wall carbon nanotubes/epoxy resin (MWNT) dispersed randomly in the resin; 2) MWNT buckypaper/resin composite materials; 3) and neat MWNT buckypaper. Initially, we use the techniques of thermogravimetry, infrared spectroscopy, nuclear magnetic resonance, energy dispersive spectroscopy, x-ray fluorescence, scanning and transmission electron microscopy for a broadening characterization of the starting materials, to evaluate its morphology, purity, chemical composition and structure, in order to optimize the properties of crosslinked resin and, consequently, of the composite systems. Important parameters such as the average molecular mass and the equivalent weight of epoxy resin (DGEBA) were determined by {sup 1}H-NMR analysis and, after that, resin/curing agent relations with Phr 10, 15, 20 and 53,2 were elaborated and investigated by thermogravimetry, the resin/curing agent relation with Phr 10 showed to be the most thermally stable. This stoichiometric relation was used to elaborate the composites. We have evaluated that the effect of adding 10 wt% of the solvent acetone to the epoxy resin preparation does not alter its properties so we have adopted two routes to fabricate the composites. In the first route we used 10 wt% of acetone and, in the second the MWNT were dispersed in the matrix without using the solvent. However, no significant difference was observed for the dispersion of the bundle tubes in both systems. The electrical conductivity of the composites and buckypapers was evaluated by impedance spectroscopy and the thermal conductivity by the flash laser flash method. Only the buckypapers presented high values for electrical conductivity (10{sup 3} S.m{sup -1}). The composite systems presented values of 10{sup -3} S.m{sup -1}, only a bit different from the value of the crosslinked resin. For thermal

  10. Sistemas inteligentes de embalagens utilizando filmes de quitosana como indicador colorimétrico de temperatura Alternative intelligent material for packaging using chitosan films as colorimetric temperature indicators

    Directory of Open Access Journals (Sweden)

    Vinícius B. V. Maciel

    2012-01-01

    Full Text Available Clorofila, um pigmento natural termossensível, foi incorporado à matriz de filmes de quitosana visando a obter sistemas inteligentes de indicação de variação de temperatura. A quitosana é um polímero biodegradável que forma filmes flexíveis com eficiente barreira ao oxigênio, podendo ser alternativa ao uso de polímeros sintéticos. Clorofila foi adicionada (0,25 g/100 g à suspensão de quitosana (2,00 g/100 g formando filmes inteligentes de quitosana (FIQ. Os efeitos da temperatura (10 °C a 50 °C e luminosidade (0 a 1000 lx foram estudados utilizando um planejamento experimental, avaliando os parâmetros de cor (L*, a*, b* e propriedades mecânicas. As suspensões de quitosana contendo clorofila foram aplicadas como revestimento em superfície de papel cartão formando o sistema de material flexível filme-papel cartão (S-FP, reduzindo significativamente o tempo de secagem. Os filmes caracterizaram-se pela homogeneidade, flexibilidade, coloração esverdeada e fácil manuseio. A variação de cor foi visualmente observada no sistema S-FP, alterando irreversivelmente de verde para amarelo quando submetido a temperaturas acima de 50 °C, independentemente da luminosidade. Desta forma, o sistema proposto tem potencial de aplicação como indicador colorimétrico de temperatura na faixa de 50 °C a 75 °C, com a vantagem de simples fabricação, biodegradabilidade e uso de materiais seguros para aplicação em contato direto com alimentos e fármacos, além do baixo custo.Chlorophyll was incorporated into chitosan films, forming intelligent systems able to detect variations in temperature. Chitosan is a biodegradable polymer that forms flexible, resistant films with an efficient oxygen barrier. Chlorophyll was added (0.25 g/100 g into chitosan suspension (2.00 g/100 g and intelligent films (FIQ were cast. The effects of temperature (10 °C to 50 °C and luminosity (0 to 1000 lx on the films were studied using an experimental design

  11. O estado da arte sobre o uso de resíduos como matérias-primas cerâmicas alternativas State of the art about the use of wastes as alternative to ceramic raw materials

    Directory of Open Access Journals (Sweden)

    Romualdo R. Menezes

    2002-01-01

    Full Text Available Os resíduos industriais e urbanos vêm-se tornando um dos mais sérios problemas que a sociedade moderna enfrenta. Sua deposição de forma inadequada provoca a degradação do meio ambiente e a contaminação dos mananciais de água e do solo. Por outro lado, técnicos da indústria cerâmica se deparam com a escassez de reservas de matérias-primas de boa qualidade em locais economicamente viáveis de exploração. Assim, este trabalho objetiva apresentar uma visão geral da possibilidade de utilização dos resíduos industriais e urbanos como matérias-primas cerâmicas alternativas, enfocando a indústria cerâmica como uma fonte economicamente viável e ecologicamente correta para reciclagem de resíduos.The industrial and urban wastes have become one of the most serious problems faced by the modern society. These wastes cause environmental degradation, with pollution and contamination of water and soil. On the other hand, the ceramic industry faces scarcity of good quality raw materials in locations close to the industries. The aim of this work is to give an overview about the possibility to use industrial and urban wastes as alternative to ceramic raw materials, focusing the use in ceramic industry as an economical and environmentally safe alternative for recycling wastes.

  12. Looking for an Alternative.

    Science.gov (United States)

    Kennedy, Jack

    1999-01-01

    Argues that high school newspapers might do well to create stronger ties with alternative weeklies. Discusses issues of niche marketing, alternative content, and alternative presentation. Notes that high school papers could learn a lot from alternative newspapers. (SR)

  13. Scaling and the start-up phase of space industrialization

    Science.gov (United States)

    Criswell, D. R.

    1979-01-01

    By terrestrial standards very little mass is needed to construct the space portion of a 10,000 megawatt (10 GW) power system. Use of lunar materials makes it reasonable to consider alternatives to silicon solar cells for conversion of sunlight to electricity and thereby avoid present major problems associated with solar cell production. Machinery needed on the moon to excavate lunar materials and deliver them to a transport system, to beneficiate lunar materials, to produce glasses and ceramics from lunar materials and to chemically process lunar materials into their major oxides and elements are minor mass fractions of the total mass of equipment needed in space to produce an SPS. In addition the processing equipment can throughput several hundred times their own mass each year with very little requirement for makeup mass from earth.

  14. Gas-injection-start and shutdown characteristics of a 2-kilowatt to 15-kilowatt Brayton power system

    Science.gov (United States)

    Cantoni, D. A.

    1972-01-01

    Two methods of starting the Brayton power system have been considered: (1) using the alternator as a motor to spin the Brayton rotating unit (BRU), and (2) spinning the BRU by forced gas injection. The first method requires the use of an auxiliary electrical power source. An alternating voltage is applied to the terminals of the alternator to drive it as an induction motor. Only gas-injection starts are discussed in this report. The gas-injection starting method requires high-pressure gas storage and valves to route the gas flow to provide correct BRU rotation. An analog computer simulation was used to size hardware and to determine safe start and shutdown procedures. The simulation was also used to define the range of conditions for successful startups. Experimental data were also obtained under various test conditions. These data verify the validity of the start and shutdown procedures.

  15. Classroom Writing Environments and Children's Early Writing Skills: An Observational Study in Head Start Classrooms

    Science.gov (United States)

    Zhang, Chenyi; Hur, Jinhee; Diamond, Karen E.; Powell, Douglas

    2015-01-01

    This study examined the classroom writing environment in 31 Head Start classrooms, and explored the relations between the writing environment, children's (N = 262) name-writing, and children's letter knowledge using pathway analysis. Our analyses showed that Head Start classrooms provided opportunities (i.e., writing materials and teachers'…

  16. Why START. [Strategic Arms Reduction Talks treaty

    Energy Technology Data Exchange (ETDEWEB)

    Mendelsohn, J.

    1991-04-01

    Barring some major unexpected downturn in US-Soviet relations, it seems likely that the long-awaited Strategic Arms Reduction Talks (START) treaty will be signed sometime in 1991. Under negotiation for the past nine years, public acceptance and Senate approval of a START treaty will be facilitated by the generally less confrontational East-West relationship which has evolved over that time, by the growing constraints on the US defense budget, and by the obvious merits of the treaty itself. Not only will the nearly complete START treaty be an extremely useful and powerful arms control agreement, it is also decidedly advantageous to US security interests. First and foremost, a START treaty will cap and reduce the steady buildup of nuclear weapons that has characterized the last 30 years of the US-Soviet strategic relationship. As a result of the basic outline originally agreed to at the Reykjavik summit, START will take a 25 to 35 percent bite out of existing nuclear arsenals, impose approximately a 50 percent cut in overall Soviet ballistic missile warheads and throw-weight (lifting power or payload capacity), and produce an exact 50 percent cut in Soviet SS-18 missiles.

  17. Research nuclear reactor start-up simulator

    International Nuclear Information System (INIS)

    This work presents the design and FPGA implementation of a research nuclear reactor start-up simulator. Its aim is to generate a set of signals that allow replacing the neutron detector for stimulated signals, to feed the measurement electronic of the start-up channels, to check its operation, together with the start-up security logic. The simulator presented can be configured on three independent channels and adjust the shape of the output pulses. Furthermore, each channel can be configured in 'rate' mode, where you can specify the growth rate of the pulse frequency in %/s. Result and details of the implementation on FPGA of the different functional blocks are given. (author)

  18. Guidelines for starting today's private practice

    Directory of Open Access Journals (Sweden)

    Schmitz ED

    2012-11-01

    Full Text Available No abstract available. Article truncated at 150 words. Starting a new practice may seem like a daunting task. The purpose of this article is to demystify the process of creating a new practice from the beginning. The cardinal rule is to keep costs low and not to outsource work that can easily be performed by any competent physician and staff. You do not need a manager, lawyer, business partner, coder or biller individually; you may be able to perform many of these services yourself. What you do need is a commitment to making your practice a success. Do not spend too much on your office space, furnishings or equipment. Start with the bare essentials. Immediately start applying to all insurance companies especially Medicare. Request an employer identification number. Set up a basic business banking account and submit the account number to the insurance companies you plan to work with. You can purchase an entire electronic healthcare record (EHR …

  19. Ruderal succession starting at different seasons

    Directory of Open Access Journals (Sweden)

    Reinhard Bornkamm

    2014-02-01

    Full Text Available Succession experiments were carried out in 1 m2 sized plots on three different soils (S = sand. SCL = silty clayey loam, CL = clayey loam. Vegetation was allowed to grow for 9 years, starting at different dates between 18.06.1969 and 1.04.1971. The greatest part of the variation of floristic composition and cover was brought about by the different soils. Direct effects of the starting season were detected only in the first two years. On sand in the first year the winter annual Conyza canadensis was well developed on the plots that had started in spring, but was poorly developed on the summer and fall plots. In the second year it decreased in the spring plots but increased in the summer and fall plots. The same was true for the winter annual Sonchus asper on CL. On SCL, however., Senecio vulgaris, belonging to the therophyta epeteia (overwintering in summer habit, was well developed in both the spring and summer plots, and showed an increase towards the second year in the fall plots only. In the later years of the experiment plots that had been started early in the year mostly were dominated by Poa pratensis ssp. angustifolia (or Quercus rubra, whereas plots that had been started late in the year mostly were dominated by Solidagn canadensis together with Artemsia vulgaris. The analyses of the transition events between the (subdominant species showed a variety of replacement patterns, but no determinated series of species following each other. It remains, therefore, unclear in what manner the differentiation between the terminal dominants may be related to the starting season.

  20. Two-Man Bobsled Push Start Analysis

    Directory of Open Access Journals (Sweden)

    Lopes Alexandre Dias

    2016-04-01

    Full Text Available The importance of push start times on bobsled performance was evidenced by some studies, but at this moment there is no article to the authors’ knowledge that describes the bobsled push start. Thus, the objectives of this study were to describe the two-man bobsled push start, analyze the differences between teams, and estimate the most important variable analyzed. We hypothesized that the pilot and brakeman athletes’ movement patterns during a bobsled pushing start can be described. The images used in this study were obtained during the men’s two-man XIV World Championship of Bobsled (2004. Fifteen best teams participating in the championship were recorded, and four start runs for each team were analyzed. The videos were captured by two digital video cameras. The pilot athletes were analyzed during the moment that they touched the lateral push bar of the sled, and the brakemen were analyzed during the first take-off and first landing. The teams were pooled in three groups of five teams using the final ranking of pushing time. We concluded that there was a distinct pattern movement for pilots and brakemen. The initial position of the majority of the pilots was localized slightly behind the bar. After touching the lateral bar, the pilots remained in a semi-squat position, pushing the sled forward in a pattern of marching movement. All brakemen used the board attached to the track as a support for both feet at the start. The brakeman gave the greatest contribution to break the inertia of the sled. There was no significant difference of movement between the three groups analyzed for the pilot and the brakeman.

  1. Soft start technique for diesel generator sets

    International Nuclear Information System (INIS)

    A diesel motor in a nuclear power plant should be of a well-proven design. It is designed for long periods of trouble-free duty, but not for the frequent and rapid test starts called for by the technical specifications. In order to decrease the dynamic forces and thermal stresses, a soft-start scheme has been implemented. By limiting the fuel injection the diesel generator will reach full speed in appr. 30 seconds. The fuel limiter is a pneumatic cylinder which mechanically limits the travel of the terminal shaft of the governor. (author)

  2. Entrepreneur How to Start an Online Business

    CERN Document Server

    Tobin, Lucy

    2012-01-01

    The secrets of the UK’s biggest online entrepreneurs revealed   Thinking of starting a business? Already have a business online and looking to take it to the next level? The wonderful world wide web has made creating a start-up that much easier. Thousands of people are out there reaping the rewards the web can bring. If you want to join them, you’ve come to the right place.  Profiling today’s foremost web entrepreneurs, Lucy Tobin - who meets successful business founders every week writing an enterprise column for The Evening Standard – takes us throug

  3. Public library start-up guide

    CERN Document Server

    Hage, Christine Lind

    2004-01-01

    An estimated thirteen million people in the U.S. are not served by a public library. This presents opportunities for creating new libraries. Involving complex, timeconsuming, and expensive decisions, the prospect of starting a library without the right direction seems overwhelming.The Public Library Start-Up Guide provides a framework for success-from looking at the big strategic picture to picking the furniture. Expert library director and author Christine Hage offers a succinct, nontechnical, and step-by-step approach covering all the practical issues for library professionals as well as non

  4. The Lean and Global Start-up

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager

    For several decades researchers have studied start-up companies with a focus on international markets, suppliers and networks from their inception and on companies that are establishing new, agile business models. This has resulted in two streams of research: The Born Global and International New...... Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

  5. Getting started with Microsoft Lync server 2013

    CERN Document Server

    Volpe, Fabrizio

    2013-01-01

    This book has a practical approach with a lot of step-by-step guides and explanations as to where and why we're doing the various operations.Getting Started with Microsoft Lync Server 2013 is a starting point for system administrators, IT pros, unified communication technicians, and decision makers in companies or in the consultancy business. For people who have never managed Lync (or a U.C. product), the book will guide you through the basic concepts and mistakes. If you are already managing a Lync deployment you will find important explanations and ideas put together in a single text. If you

  6. Plan de empresa: Start Up Studio

    OpenAIRE

    Pi, Marc

    2014-01-01

    El siguiente proyecto presenta el plan de empresa para la de creación de un negocio que se dedicara a realizar trabajos audiovisuales para empresas, autónomos y emprendedores. Esta ofrecerá, inicialmente, su servicio en la ciudad de Barcelona y su área metropolitana. En el caso de que en un futuro hubiese mucha demanda se podría expandir el servicio a toda España. El nombre de la empresa es START UP STUDIO. Start Up Studio se rige por un plan de empresa que define la empresa y los producto...

  7. Nanostructured Materials for Renewable Alternative Energy

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, Gregory

    2013-07-24

    This project has been in effect from July 25th, 2008 to July 24th, 2013. It supported 19 graduate students and 6 post-doctoral students and resulted in 23 publications, 7 articles in preparation, 44 presentations, and many other outreach efforts. Two representative recent publications are appended to this report. The project brought in more than $750,000 in cost share from North Carolina State University. The project funds also supported the purchase and installation of approximately $667,000 in equipment supporting solar energy research.

  8. Graphene-chitosan self-start ultrafast laser setup

    Science.gov (United States)

    Tarka, Jan; Bogusławski, Jakub; Sotor, Jaroslaw; Sobon, Grzegorz; Jagiełło, Joanna; Lipinska, Ludwika; Abramski, Krzysztof M.

    2014-12-01

    We present first to our knowledge self-starting graphene-chitosan based ultrafast fiber laser setup. Graphene-chitosan composite placed between two fibres connectors is saturable absorber in demonstrated setup and is responsible for modelocking operation. Laser is built with polarization maintaining fibres which grants self-start feature. Laser produces ~300 fs soliton pulses centered at 1566 nm with 10 nm FHWM optical bandwidth. Time bandwidth product of demonstrated laser is 0.37. Repetition rate of 42 MHz and average output power of 1.2 mw corresponds to pulse energy and peak power of 20 pJ and 62 W, respectively. As an active media in laser Erbium-doper fiber was used. Presented setup proves graphene is novel promising material for ultrafast lasers production at worldwide scale.

  9. Start time delays in operating room: Different perspectives

    Directory of Open Access Journals (Sweden)

    Babita Gupta

    2011-01-01

    Full Text Available Background: Healthcare expenditure is a serious concern, with escalating costs failing to meet the expectations of quality care. The treatment capacities are limited in a hospital setting and the operating rooms (ORs. Their optimal utilization is vital in efficient hospital management. Starting late means considerable wait time for staff, patients and waste of resources. We planned an audit to assess different perspectives of the residents in surgical specialities and anesthesia and OR staff nurses so as to know the causative factors of operative delay. This can help develop a practical model to decrease start time delays in operating room (ORs. Aims: An audit to assess different perspectives of the Operating room (OR staff with respect to the varied causative factors of operative delay in the OR. To aid in the development of a practical model to decrease start time delays in ORs and facilitate on-time starts at Jai Prakash Narayan Apex Trauma centre (JPNATC, All India Institute of Medical Sciences (AIIMS, New Delhi. Methods: We prepared a questionnaire seeking the five main reasons of delay as per their perspective. Results: The available data was analysed. Analysis of the data demonstrated the common causative factors in start time operative delays as: a lack of proper planning, deficiencies in team work, communication gap and limited availability of trained supporting staff. Conclusions: The preparation of the equipment and required material for the OR cases must be done well in advance. Utilization of newer technology enables timely booking and scheduling of cases. Improved inter-departmental coordination and compliance with preanesthetic instructions needs to be ensured. It is essential that the anesthesiologists perform their work promptly, well in time . and supervise the proceedings as the OR manager. This audit is a step forward in defining the need of effective OR planning for continuous quality improvement.

  10. FMDP reactor alternative summary report: Volume 4, Evolutionary LWR alternative

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] have become surplus to national defense needs both in the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES&H) consequences if surplus fissile materials are not properly managed. The purpose of this report is to provide schedule, cost, and technical information that will be used to support the Record of Process (ROD). Following the screening process, DOE/MD via its national laboratories initiated a more detailed analysis activity to further evaluate each of the ten plutonium disposition alternatives that survived the screening process. Three ``Alternative Teams,`` chartered by DOE and comprised of technical experts from across the DOE national laboratory complex, conducted these analyses. One team was chartered for each of the major disposition classes (borehole, immobilization, and reactors). During the last year and a half, the Fissile Materials Disposition Program (FMDP) Reactor Alternative Team (RxAT) has conducted extensive analyses of the cost, schedule, technical maturity, S&S, and other characteristics of reactor-based plutonium disposition. The results of the RxAT`s analyses of the existing LWR, CANDU, and partially complete LWR alternatives are documented in Volumes 1-3 of this report. This document (Volume 4) summarizes the results of these analyses for the ELWR-based plutonium disposition option.

  11. FMDP reactor alternative summary report: Volume 4, Evolutionary LWR alternative

    International Nuclear Information System (INIS)

    Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] have become surplus to national defense needs both in the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES ampersand H) consequences if surplus fissile materials are not properly managed. The purpose of this report is to provide schedule, cost, and technical information that will be used to support the Record of Process (ROD). Following the screening process, DOE/MD via its national laboratories initiated a more detailed analysis activity to further evaluate each of the ten plutonium disposition alternatives that survived the screening process. Three ''Alternative Teams,'' chartered by DOE and comprised of technical experts from across the DOE national laboratory complex, conducted these analyses. One team was chartered for each of the major disposition classes (borehole, immobilization, and reactors). During the last year and a half, the Fissile Materials Disposition Program (FMDP) Reactor Alternative Team (RxAT) has conducted extensive analyses of the cost, schedule, technical maturity, S ampersand S, and other characteristics of reactor-based plutonium disposition. The results of the RxAT's analyses of the existing LWR, CANDU, and partially complete LWR alternatives are documented in Volumes 1-3 of this report. This document (Volume 4) summarizes the results of these analyses for the ELWR-based plutonium disposition option

  12. Moisture buffering capacity of highly absorbing materials

    Energy Technology Data Exchange (ETDEWEB)

    Cerolini, S.; D' Orazio, M.; Stazi, A. [Department of Architecture, Construction and Structures (DACS), Faculty of Engineering, Polytechnic University of Marche, Via Brecce Bianche, 60100 Ancona (Italy); Di Perna, C. [Department of Energetics, Faculty of Engineering, Polytechnic University of Marche, Via Brecce Bianche, 60100 Ancona (Italy)

    2009-02-15

    This research investigates the possibility to use highly absorbing materials to dampen indoor RH% variations. The practical MBV of sodium polyacrylate, cellulose-based material, perlite and gypsum is evaluated for a daily cyclic exposure that alternates high (75%) and low (33%) RH% levels for 8 h and 16 h, respectively. The adjustment velocity to RH% variations and the presence of hysteretic phenomena are also presented. The cellulose-based material proves to be the most suitable for moisture buffering applications. Starting from this material's properties, the effect of thickness, vapour resistance factor ({mu}) and mass surface exchange coefficient (Z{sub v}) on sorption capacity is evaluated by the use of a numerical model. (author)

  13. Construction of Shanghai Chemical Park Started

    Institute of Scientific and Technical Information of China (English)

    Wang Yan

    2001-01-01

    @@ Shanghai Chemical Industrial Park started construction on January 6, 2001 with the first pile driven for the 200,000-ton phenol acetone plant of Gaoqiao Branch,Sinopec Ltd. This is one of the largest industrial investment projects of the city of the country as well as the city at the beginning of the new century.

  14. Start-up incentives the Netherlands

    NARCIS (Netherlands)

    Bekker, S.; van den Eijnden, J.

    2014-01-01

    Generally, there are three different types of start-up incentive for unemployed and inactive people in the Netherlands. The first is a set of incentives for potential entrepreneurs receiving Unemployment Benefits (UB) (Werloosheidwet - WW). Such incentives have existed since 2006 and were adjusted i

  15. Starting wages respond to employer's risk

    NARCIS (Netherlands)

    P. Berkhout; J. Hartog; H van Ophem

    2009-01-01

    Firms hiring fresh graduates face uncertainty on the future productivity of workers. Theory suggests that starting wages reflect this, with lower pay for greater uncertainty. We use the dispersion of exam grades within a field of education as an indicator of the unobserved heterogeneity that employe

  16. Starting wages respond to employer's risk

    NARCIS (Netherlands)

    P. Berkhout; J. Hartog; H. van Ophem

    2014-01-01

    Firms hiring new graduates face uncertainty on the future productivity of workers. Theory suggests that starting wages reflect this, with lower pay for greater uncertainty. We use the dispersion of exam grades within a field of education as an indicator of the unobserved heterogeneity that employers

  17. Verifying the INF and START treaties

    International Nuclear Information System (INIS)

    The INF and START Treaties form the basis for constraints on nuclear weapons. Their verification provisions are one of the great success stories of modern arms control and will be an important part of the foundation upon which the verification regime for further constraints on nuclear weapons will be constructed

  18. Jinde Lead lead smelting project starts construction

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>On Dec.20,the lead smelting project of Jiangxi Jinde Lead started construction in Dexin as a technical renovation project on environmental treatment of Jiangxi Metallurgical Group.The project is the one with the largest investment of Provincial Metallurgical Group in non-ferrous

  19. Effects of sled towing on sprint starts.

    Science.gov (United States)

    Cottle, Casey A; Carlson, Lara A; Lawrence, Michael A

    2014-05-01

    Sled towing is a popular method of sprint training. Researchers have struggled to identify a loading scheme that is most appropriate to improve sprint performance in the acceleration phase. The purpose of this study was to determine if loads of 10% body weight (BWT) or 20% BWT produced significantly greater propulsive ground reaction force (GRF) impulse, peak propulsive GRF, or a greater propulsive rate of force development (RFD) than an unweighted sprint start. Seventeen healthy court and field athletes (10 men, 7 women; 20.9 ± 1.1 years) completed 5 starts of each condition (unweighted, 10% BWT, 20% BWT). Participants began each start in an upright staggered stance. Propulsive GRF impulse was greater in the 20% BWT condition than the unweighted condition in both limbs and greater in the 20% BWT condition than the 10% BWT condition in the front leg only, and vertical GRF impulse was greater in the 20% BWT than the unweighted condition. In summary, our results suggest that a 10% BWT load is not sufficient to increase propulsive GRF impulse. A loading scheme of 20% BWT is sufficient to increase propulsive GRF impulse. Coaches seeking to improve sprint starts may observe improvements using a load of 20% BWT during training while towing a sled.

  20. EU Emission Trading: Starting with Carbon Dioxide

    DEFF Research Database (Denmark)

    Vesterdal, Morten; Svendsen, Gert Tinggaard

    2003-01-01

    The Commission of the European Union wants to start a limited emission trading scheme by 2005 within the Community to enable "learning-by-doing" prior to the Kyoto Protocol. This to accomplish the desired 8% target level for six different greenhouse gases. However, in the EU it is not clear whether...

  1. Addressing Tooth Decay in Head Start Children

    Science.gov (United States)

    Knowlden, Adam P.; Hill, Lawrence F.; Alles-White, Monica L.; Cottrell, Randall R.

    2012-01-01

    Tooth decay is the most prevalent chronic disease of childhood. Oral health education and dental services are crucial to reducing the number of children afflicted with dental cavities. Due to limited access to preventative care, Head Start children are particularly vulnerable to tooth decay. This article outlines practical implications of a…

  2. Single phase induction motor with starting performance

    Energy Technology Data Exchange (ETDEWEB)

    Popescu, M.; Demeter, E. [Research Institute for Electrical Machines, ICPE-ME, Bucharest (Romania); Navrapescu, V. [University `Politehnica` Bucharest, Electrical Engineering Faculty Splaiul Independentei, Bucharest (Romania)

    1997-12-31

    The paper presents problems related to a special type of single phase induction motor. The main novelty consists in the use of a conducting (aluminium casted) shell distributed on the periferic region of the rotor. As a result the starting performance, as well as the rated ones, is much improved in comparison with the conventional construction. (orig.) 4 refs.

  3. Getting started with OrientDB

    CERN Document Server

    Tesoriero, Claudio

    2013-01-01

    A standard tutorial aimed at making you an OrientDB expert, through the use of practical examples, explained in a step-by-step format.Getting Started with OrientDB 1.3.0 is great for database designers, developers, and systems engineers. It is assumed that you are familiar with NoSQL concepts, Java, and networking principles.

  4. Getting started with Magento module development

    CERN Document Server

    Ajzele, Branko

    2013-01-01

    This project-based tutorial gives you a strong foundation and guides you through practical, real-world examples.This book contains valuable insights for both newbies and already established Magento developers. This book is targeted at new and intermediate PHP developers starting afresh with Magento module development.

  5. Systematic clustering of transcription start site landscapes

    DEFF Research Database (Denmark)

    Zhao, Xiaobei; Valen, Eivind; Parker, Brian J;

    2011-01-01

    Genome-wide, high-throughput methods for transcription start site (TSS) detection have shown that most promoters have an array of neighboring TSSs where some are used more than others, forming a distribution of initiation propensities. TSS distributions (TSSDs) vary widely between promoters...

  6. Alternative technical summary report for immobilized disposition in deep boreholes: Immobilized disposal of plutonium in coated ceramic pellets in grout without canisters, Version 4.0. Fissile materials disposition program

    Energy Technology Data Exchange (ETDEWEB)

    Wijesinghe, A.M.

    1996-08-23

    This paper summarizes and compares the immobilized and direct borehole disposition alternatives previously presented in the alternative technical summary. The important design concepts, facility features and operational procedures are first briefly described. This is followed by a discussion of the issues that affect the evaluation of each alternative against the programmatic assessment criteria that have been established for selecting the preferred alternatives for plutonium disposition.

  7. An Alternative to Business Plan Based Advice for Start-Ups?

    Science.gov (United States)

    Bridge, Simon; Hegarty, Cecilia

    2012-01-01

    Business plans are advocated by many business support professionals and others, such as educators in higher education institutions, because they suit their purposes. A typical view is that a business plan is "one of the most important steps in setting up any new business" (Burns, 2011); but their hegemony is now being questioned. Sarasvathy (2008)…

  8. Alternative thinking about starting points of obesity. Development of child taste preferences.

    Science.gov (United States)

    Cornwell, T Bettina; McAlister, Anna R

    2011-04-01

    Food marketers are at the epicenter of criticism for the unfolding obesity epidemic as societies consider banning advertising to children and taxing "junk" foods. While marketing's role in obesity is not well understood, there is clear evidence that children are regularly targeted with calorie-dense, nutrient-poor food. Much of the past research seeks to understand how marketing influences brand preference and child requests. The authors argue that understanding palate development offers new insights for discussion. Two studies consider whether a sugar/fat/salt (SFS) palate is linked to children's knowledge of food brands, experience with products, and advertising. In study 1, the authors develop a survey measure of taste preferences and find that a child's SFS palate (as reported by parents) relates significantly to children's self-reported food choices. Study 2 examines how knowledge of certain branded food and drinks is related to palate. Findings show that children with detailed mental representations of fast-food and soda brands--developed via advertising and experience--have higher scores on the SFS palate scale. PMID:21238522

  9. First Impressions: An Alternative Way to Start a Systems Development Course

    Science.gov (United States)

    Fellers, Jack W.

    2008-01-01

    The first meeting of any course and its many activities sets in motion the establishment of a course climate and addressing student expectations. How can students be actively and collaboratively engaged, in a non-threatening environment, having their curiosity aroused, and begin to learn about the course all during the first class meeting? This…

  10. FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

    International Nuclear Information System (INIS)

    Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES ampersand H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives

  11. FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

    Energy Technology Data Exchange (ETDEWEB)

    Greene, S.R.; Bevard, B.B. [and others

    1996-10-07

    Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES&H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives.

  12. Photovoltaic Materials

    Energy Technology Data Exchange (ETDEWEB)

    Duty, C.; Angelini, J.; Armstrong, B.; Bennett, C.; Evans, B.; Jellison, G. E.; Joshi, P.; List, F.; Paranthaman, P.; Parish, C.; Wereszczak, A.

    2012-10-15

    cells and modules in the field for 25 years. Under this project, Ferro leveraged world leading analytical capabilities at ORNL to characterize the paste-to-silicon interface microstructure and develop high efficiency next generation contact pastes. Ampulse Corporation is developing a revolutionary crystalline-silicon (c-Si) thin-film solar photovoltaic (PV) technology. Utilizing uniquely-textured substrates and buffer materials from the Oak Ridge National Laboratory (ORNL), and breakthroughs in Hot-Wire Chemical Vapor Deposition (HW-CVD) techniques in epitaxial silicon developed at the National Renewable Energy Laboratory (NREL), Ampulse is creating a solar technology that is tunable in silicon thickness, and hence in efficiency and economics, to meet the specific requirements of multiple solar PV applications. This project focused on the development of a high rate deposition process to deposit Si, Ge, and Si1-xGex films as an alternate to hot-wire CVD. Mossey Creek Solar is a start-up company with great expertise in the solar field. The primary interest is to create and preserve jobs in the solar sector by developing high-yield, low-cost, high-efficiency solar cells using MSC-patented and -proprietary technologies. The specific goal of this project was to produce large grain formation in thin, net-shape-thickness mc-Si wafers processed with high-purity silicon powder and ORNL's plasma arc lamp melting without introducing impurities that compromise absorption coefficient and carrier lifetime. As part of this project, ORNL also added specific pieces of equipment to enhance our ability to provide unique insight for the solar industry. These capabilities include a moisture barrier measurement system, a combined physical vapor deposition and sputtering system dedicated to cadmium-containing deposits, adeep level transient spectroscopy system useful for identifying defects, an integrating sphere photoluminescence system, and a high-speed ink jet printing system. These

  13. Optimal starting block configuration in sprint running; a comparison of biological and prosthetic legs.

    Science.gov (United States)

    Taboga, Paolo; Grabowski, Alena M; di Prampero, Pietro Enrico; Kram, Rodger

    2014-06-01

    In the 2012 Paralympic 100 m and 200 m finals, 86% of athletes with a unilateral amputation placed their unaffected leg on the front starting block. Can this preference be explained biomechanically? We measured the biomechanical effects of starting block configuration for seven nonamputee sprinters and nine athletes with a unilateral amputation. Each subject performed six starts, alternating between their usual and unusual starting block configurations. When sprinters with an amputation placed their unaffected leg on the front block, they developed 6% greater mean resultant combined force compared with the opposite configuration (1.38 ± 0.06 vs 1.30 ± 0.11 BW, P = .015). However, because of a more vertical push angle, horizontal acceleration performance was equivalent between starting block configurations. We then used force data from each sprinter with an amputation to calculate the hypothetical starting mechanics for a virtual nonamputee (two unaffected legs) and a virtual bilateral amputee (two affected legs). Accelerations of virtual bilateral amputees were 15% slower compared with athletes with a unilateral amputation, which in turn were 11% slower than virtual nonamputees. Our biomechanical data do not explain the starting block configuration preference but they do explain the starting performance differences observed between nonamputee athletes and those with leg amputations.

  14. Single start multiple stop time digitizer

    International Nuclear Information System (INIS)

    A single start multiple stop time digitizer has been developed which can digitize the time between a start pulse and multiple stop pulses. The system has been designed as a PC add on card. The resolution of the instrument is 10 nSecs and the maximum length of time that it can measure is 1.28 milliseconds. Apart from time digitization, it can also resolve the height of the incoming pulses into 64 levels. After each input pulse the system dead time is less than 300 nSecs. The driver software for this card has been developed on DOS platform. It uses graphical user interface to provide a user friendly environment. The system is intended to be used in time of flight mass spectroscopy experiments. It can also be used for time of flight experiments in nuclear physics. (author). 2 figs

  15. Start currents in an overmoded gyrotron

    Science.gov (United States)

    Yeddulla, M.; Nusinovich, G. S.; Antonsen, T. M.

    2003-11-01

    High-power long-pulse millimeter-wave gyrotrons operate in high-order modes. The spectral density of these modes is very high. Therefore, self-excitation conditions can be fulfilled for several modes simultaneously. Correspondingly, in order to determine which mode will be excited first in such a device, the starting currents of competing modes should be calculated much more accurately than in gyrotrons with a rarer spectrum. In the present paper, an existing linear theory is generalized to take into account effects of magnetic field tapering, cavity profile, finite beam thickness, velocity spread and axially dependent beam coupling to the fields of competing modes. Starting currents are calculated for the operating and the most dangerous competing mode in a 140 GHz gyrotron, which is under development at Communication and Power Industries. Calculations show that the radial position of the electron beam plays a critical role in deciding which mode dominates the mode competition.

  16. Liquid phase sintered SiC ceramics from starting materials of different grade Cerâmicas à base de SiC sinterizadas via fase líquida a partir de matérias-primas de diferentes purezas

    Directory of Open Access Journals (Sweden)

    V. A. Izhevskyi

    2004-09-01

    Full Text Available Possibility of high performance ceramics manufactured from commercial SiC powder of technical grade has been shown. Sintering behavior and microstructure formation under conditions of liquid phase sintering (LPS with oxynitride sintering aids (AlN-Y2O3 of three SiC-based compositions have been investigated. Two of the compositions were based on Alcoa 1000 SiC powder of technical grade, and the third one, which was used as a reference, was based on H.C. Starck UF-15 fine grade commercial powder. Milling process used for Alcoa 1000 SiC powder granulometry improvement has been investigated in detail, while chemical treatment of milled SiC powders has been used for pick-up impurities removal. Dilatometric experiments showed that SiC powder of technical grade after appropriate treatment exhibits sinterability comparable with the fine grade SiC. Microstructural investigations performed on sintered samples showed that the final microstructure of the Alcoa 1000 SiC based materials was practically identical with the H.C. Starck SiC based reference ones. Preliminary investigations of hardness and fracture toughness were carried out revealing excellent results for the materials produced from cheaper, nationally produced starting powder.Neste trabalho é apresentada a possibilidade de obtenção de cerâmicas de SiC de alto desempenho a partir de matéria-prima comercial de grau técnico. Foi realizado o estudo de sinterização via fase líquida e desenvolvimento microestrutural de três composições à base de SiC tendo como aditivos de sinterização AlN e Y2O3 . Duas destas composições são à base de SiC-1000 da Alcoa, grau técnico, e a terceira, utilizada como referência, à base do UF-15 da H.C. Starck - Alemanha, pó comercial de granulometria fina. O processo de moagem do pó SiC-1000 da Alcoa foi acompanhado por medidas de distribuição granulométrica e posterior ataque químico, para remoção de impurezas. Os pós de grau técnico, ap

  17. Business Models for Start up Business

    OpenAIRE

    Boban, Nitin

    2010-01-01

    Gamingdom is a new start up venture that provides online gaming service utilising the latest cloud computing technology. The high demand, popularity and exponential growth in the number of gaming enthusiasts and the market have brought about this innovative idea. This new venture aims to provide an easy method of gaming through the internet without heavy expenses on hardware and software and also minimising the existing high rate of piracy. A business model is an essential tool for buildin...

  18. New Start of “Psychological Thought”

    Directory of Open Access Journals (Sweden)

    Stanislava Stoyanova

    2012-05-01

    Full Text Available The history and the mission of Psychological Thought are presented. The scientific journal “Psychological Thought” started its existence as an idea of the colleagues at the Department of Psychology at South-West University “Neofit Rilski” in 2006. Seven print issues were published from 2006 to 2009 (2 issues per year. Each issue included average ten articles published in Bulgarian or in English.

  19. Getting started with MariaDB

    CERN Document Server

    Bartholomew, Daniel

    2013-01-01

    A practical, hands-on, beginner-friendly guide to installing and using MariaDB.Getting Started with MariaDB is for anyone who wants to learn more about databases in general or MariaDB in particular. No prior database experience is required. It is assumed that you have basic knowledge of software installation, editing files with a text editor, and using the command line and terminal.

  20. Getting started with nopCommerce

    CERN Document Server

    Atkinson, Brandon

    2013-01-01

    A friendly, tutorial style book, which will help you learn your way through creating a live storefront with nopCommerce in a step-by-step manner.Getting Started with nopCommerce is for anyone who wants to sell products online using nopCommerce. If you are a non-technical person and are discouraged by the complexity of this powerful e-commerce application, then this book is for you.

  1. New START: The Contentious Road to Ratification

    Directory of Open Access Journals (Sweden)

    Elizabeth Zolotukhina

    2011-01-01

    Full Text Available Senate ratification of the New START treaty re-established effective bilateral inspection and monitoring of American and Russian nuclear holdings and has the potential to further enhance U.S.-Russian cooperation on key issues, including containing the Iranian nuclear program, and further reductions in the two countries' arsenals. Although the accord was widely heralded as a foreign policy success of the Obama administration, the contentious Senate ratification may impede future progress on arms control.

  2. A Fast-Starting Robotic Fish

    Science.gov (United States)

    Modarres-Sadeghi, Yahya; Watts, Matthew; Conte, Joe; Hover, Franz; Triantafyllou, Michael

    2009-11-01

    We have built a simple mechanical system to emulate the fast-start performance of fish. The system consisted of a thin metal beam covered by a urethane rubber fish body. The body form of the mechanical fish in this work was modeled from a pike species, which is the most successfully studied fast-start specialist species. The mechanical fish was held in curvature and hung in water by two restraining lines, which were simultaneously released by pneumatic cutting mechanisms. The potential energy in the beam was transferred into the fluid, thereby accelerating the fish, similar to a pike. We measured the resulting velocity and acceleration, as well as the efficiency of propulsion for the mechanical fish model and also ran a series of flow visualization tests to observe the resulting flow pattern. We also studied the influence of stiffness and geometry of the tail on the efficiency of propulsion and flow pattern. The hydrodynamic efficiency of the fish, calculated by the transfer of energy, was around 10%. Flow visualization of the mechanical fast-start wake was also analyzed, showing that the acceleration is associated with the fast movement of an intense vortex in a near-lateral direction.

  3. A unique, consistent identifier for alternatively spliced transcript variants.

    Directory of Open Access Journals (Sweden)

    Alberto Riva

    Full Text Available BACKGROUND: As research into alternative splicing reveals the fundamental importance of this phenomenon in the genome expression of higher organisms, there is an increasing need for a standardized, consistent and unique identifier for alternatively spliced isoforms. Such an identifier would be useful to eliminate ambiguities in references to gene isoforms, and would allow for the reliable comparison of isoforms from different sources (e.g., known genes vs. computational predictions. Commonly used identifiers for gene transcripts prove to be unsuitable for this purpose. METHODOLOGY: We propose an algorithm to compute an isoform signature based on the arrangement of exons and introns in a primary transcript. The isoform signature uniquely identifies a transcript structure, and can therefore be used as a key in databases of alternatively spliced isoforms, or to compare alternative splicing predictions produced by different methods. In this paper we present the algorithm to generate isoform signatures, we provide some examples of its application, and we describe a web-based resource to generate isoform signatures and use them in database searches. CONCLUSIONS: Isoform signatures are simple, so that they can be easily generated and included in publications and databases, but flexible enough to unambiguously represent all possible isoform structures, including information about coding sequence position and variable transcription start and end sites. We believe that the adoption of isoform signatures can help establish a consistent, unambiguous nomenclature for alternative splicing isoforms. The system described in this paper is freely available at http://genome.ufl.edu/genesig/, and supplementary materials can be found at http://genome.ufl.edu/genesig-files/.

  4. Alternatives to neoliberalism?

    DEFF Research Database (Denmark)

    Warring, Niels; Ahrenkiel, Annegrethe; Nielsen, Birger Steen;

    This paper will discuss the consequences of neoliberal governance in Danish day care centres, the social educators’ response, and the possible development of alternatives based on collective participation of social educators and union representatives. We will show how important and unnoticed...... professional competencies come under pressure, and how collective interest representation is challenged. We will discuss how concepts of “gestural knowledge”, “coherence” and “rhythm” open for a new understanding of professional competence. And we will conclude that the social educators and their unions have...... the possibility to contribute to the development of a new welfare paradigm. The paper is based on material from two research projects (Ahrenkiel et al. 2009, 2011) involving social educators and union representatives in day care institutions. We have observed everyday work activities in day care...

  5. 76 FR 37174 - Capital Investment Program-New Starts and Small Starts Program Funds

    Science.gov (United States)

    2011-06-24

    ... promote livable communities, improve mobility by providing alternatives to automobile, and reduce the... the Transportation Electronic Award Management system. Pre-award authority is granted as of February...

  6. Structural materials assessment

    International Nuclear Information System (INIS)

    The selection of first wall and structural materials is strongly dependent on the proposed design of breeding blanket components and the targets for a fusion reactor development. An envelope of parameters which have to be covered in future R and D activities and which have been adapted in different proposals has been compiled. A short description of interesting material groups like ferritic-martensitic steels, vanadium alloys and ceramic composites, major criteria for their selection and a survey on existing irradiation data is given. This is followed by a comparative assessment of relevant properties and an identification of major issues for each material group. A more detailed proposal for the future R and D activities is then developed for the ferritic-martensitic steels, the present reference material for the European Breeding Blankets. It describes different phases of development necessary for the qualification of this material for DEMO and gives time schedules which are compatible with parallel component developments. A more selective strategy is proposed for the development of vanadium alloys and the ceramic composite material SiC/SiC. For these alternatives work should be concentrated on identified high-risk issues, before a comprehensive development programme is started. The necessity of efficient irradiation facilities to study the irradiation behaviour of the materials under simulation - and realistic fusion conditions is discussed. The availability of high flux fission reactors and necessary extensions of irradiation rigs for the next decade is stressed. Finally it is shown that for the qualification of materials under realistic fusion conditions a high-energetic, high-flux neutron source is mandatory. An accelerator-driven d-Li neutron source (IFMIF) can fulfil essential users requirements as test bed for materials and can technically be made available in due time. In combination with ITER and DEMO, where a concept verification and full scale

  7. Alternate fuels; Combustibles alternos

    Energy Technology Data Exchange (ETDEWEB)

    Romero Paredes R, Hernando; Ambriz G, Juan Jose [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

    2003-07-01

    In the definition and description of alternate fuels we must center ourselves in those technological alternatives that allow to obtain compounds that differ from the traditional ones, in their forms to be obtained. In this article it is tried to give an overview of alternate fuels to the conventional derivatives of petroleum and that allow to have a clear idea on the tendencies of modern investigation and the technological developments that can be implemented in the short term. It is not pretended to include all the tendencies and developments of the present world, but those that can hit in a relatively short term, in accordance with agreed with the average life of conventional fuels. Nevertheless, most of the conversion principles are applicable to the spectrum of carbonaceous or cellulosic materials which are in nature, are cultivated or wastes of organic origin. Thus one will approach them in a successive way, the physical, chemical and biological conversions that can take place in a production process of an alternate fuel or the same direct use of the fuel such as burning the sweepings derived from the forests. [Spanish] En la definicion y descripcion de combustibles alternos nos debemos centrar en aquellas alternativas tecnologicas que permitan obtener compuestos que difieren de los tradicionales, al menos en sus formas de ser obtenidos. En este articulo se pretende dar un panorama de los combustibles alternos a los convencionales derivados del petroleo y que permita tener una idea clara sobre las tendencias de la investigacion moderna y los desarrollos tecnologicos que puedan ser implementados en el corto plazo. No se pretende abarcar todas las tendencias y desarrollos del mundo actual, sino aquellas que pueden impactar en un plazo relativamente corto, acordes con la vida media de los combustibles convencionales. Sin embargo, la mayor parte de los principios de conversion son aplicables al espectro de materiales carbonaceos o celulosicos los cuales se

  8. Investigation on a-C:H:Me coated substrates as an alternative bipolar plate material in all-vanadium redox-flow batteries; Untersuchungen an a-C:H:Me beschichteten Substraten zur Eignung als alternatives Bipolarplattenmaterial fuer waessrige Vanadium Redox-Flow Batterien

    Energy Technology Data Exchange (ETDEWEB)

    Richards, Justin Frederick

    2015-07-01

    of a pore in the coatings, where higher concentrations of metallic carbides are assumed to catalyze hydrogen evolution. SECM measurements proved to be an useful and powerful tool to investigate corrosion at a-C:H:Me coatings at defects which cannot be resolved by light microscopic measurements. The validation of metallic substrates coated with a 6,61 μm a-C:H:Ti (20 at % Ti) on an coldrolled stainless steel strip (1.4301) showed acceptable performance in real laboratory cells. Despite the fact of showing a faster decreasing cell efficiency than the graphite composite plates, the a-C:H:Ti coatings proved to affect the hydrogen evolution overpotential less than the graphite material when cathodically stressed. Although the defect density and size of an a-C:H:Ti coatings on 1.4301 stainless steel has to be reduced, the mechanical properties and also their possibility to be mass produced showed that coated metallic bipolar plates can be an alternative bipolar plate material for all-vanadium redox flow batteries.

  9. China Starts Its Lunar Exploration Prbgram

    Institute of Scientific and Technical Information of China (English)

    RenShufang

    2004-01-01

    Why China Starts Lunar Exploration Program.Lunar exploration is always a subject of great interest, for the earth's I nearest neighbour probably holds the key to humanity's future subsistence and development. The unique mineral and energy resources on the moon are important supplement and reserve to the Earth resources, which will generate farreaching influence on the sustainable development of human society. The helium-3 resource unique to lunar soil is a clean, efficient, safe and cheap new-type nuclear fusion fuel, and it will help change the energy structure of human society.

  10. Getting started in 3D with Maya

    CERN Document Server

    Watkins, Adam

    2012-01-01

    Deliver professional-level 3D content in no time with this comprehensive guide to 3D animation with Maya. With over 12 years of training experience, plus several award winning students under his belt, author Adam Watkins is the ideal mentor to get you up to speed with 3D in Maya. Using a structured and pragmatic approach Getting Started in 3D with Maya begins with basic theory of fundamental techniques, then builds on this knowledge using practical examples and projects to put your new skills to the test. Prepared so that you can learn in an organic fashion, each chapter builds on the know

  11. Getting started with the Lazarus IDE

    CERN Document Server

    Person, Roderick

    2013-01-01

    This book is written in a simple, easy-to-understand format with lots of screenshots and step-by-step explanations.This book is geared toward developers that have a familiarity with Delphi or Free Pascal and would like to start using the open source Lazarus Integrated Development Environment. You should have knowledge of creating a console and GUI applications as well as creating basic components. Example source code and projects are provided to help learn the differences between Delphi and Lazarus projects.

  12. Getting started with ownCloud

    CERN Document Server

    Patawari, Aditya

    2013-01-01

    This is a standard, precise, and short tutorial for setting up ownCloud and includes advanced topics like encryption, user management, and server security. This ownCloud book would be an ideal starting point for anyone who wants to store their data and also share it.This book is for first time users as well as administrators who are interested or responsible for managing an ownCloud instance. You do not need any prior experience with any of the technology, including Linux/Windows, Apache/IIS, SQLite/MySQL, or even PHP. It is a beginner-friendly book, written with a first time user in mind.

  13. Getting started with Zurb Foundation 4

    CERN Document Server

    Patterson, Andrew D

    2013-01-01

    The book starts with the basics of Foundation and helps you build your skills as you advance from installation to design, configuration, and customization with examples at every step.This book will be of great benefit to web architects, designers, and builders. While it helps to be a programmer, it isn't necessary for this book. You should be familiar with the basic principles of responsive web design and have a desire to create a professional website that looks great on both mobile devices and regular displays.

  14. Take Control of Getting Started with Dreamweaver

    CERN Document Server

    Keller, Arnie

    2009-01-01

    Learn fundamental Web design principles and become comfortable working in Dreamweaver's complex interface! Dreamweaver 8 is a great Web design tool for pros, but newcomers may be overwhelmed by its interface or want to know more about how to work creatively and intelligently in the program. Help is at hand in Take Control of Getting Started with Dreamweaver, which offers a detailed tutorial for making your first site in Dreamweaver. Author Arnie Keller, who teaches Web design at the University of Victoria, shows you how to style type the smart way with CSS, create a sophisticated page layout

  15. From Jam to Start-up

    DEFF Research Database (Denmark)

    Bering Kjæhr, Emil; Lyngbye Hvid Jensen, Jane; Schoenau-Fog, Henrik;

    2015-01-01

    the foundation for new start-up companies. There are, however, an even larger group of very creative and innovative games and artifacts with great potential that go unpublished. This potentially leads to a loss of entrepreneurial opportunities and ultimately the jobs and careers such games could have fostered...... with a sample consisting of 56 participants from several game jams was performed to investigate the mindset behind the numerous developers never pursuing their entrepreneurial opportunity. Furthermore, obser- vations and semi-structured interviews were conducted with game company owners in order to explore...

  16. Getting started with FortiGate

    CERN Document Server

    Fabbri, Rosato

    2013-01-01

    This book is a step-by-step tutorial that will teach you everything you need to know about the deployment and management of FortiGate, including high availability, complex routing, various kinds of VPN working, user authentication, security rules and controls on applications, and mail and Internet access.This book is intended for network administrators, security managers, and IT pros. It is a great starting point if you have to administer or configure a FortiGate unit, especially if you have no previous experience. For people that have never managed a FortiGate unit, the book helpfully walks t

  17. Start your own information marketing business

    CERN Document Server

    Skrob, Robert

    2013-01-01

    Breaking down the information marketing world from A to Z, the undisputed info marketing expert offers professional strategies to set up a successful information marketing business. These businesses are easy to start, can be run from home, don't require any employees, need little cash outlay, can be run part-time, and can produce millions of dollars a year. Readers learn everything they need to jump into this lucrative field, creating an entirely new business that gives them added income or replaces their current salary entirely.

  18. Getting started in academic cardiothoracic surgery.

    Science.gov (United States)

    Verrier, E D

    2000-04-01

    Preparing to begin a career in academic cardiothoracic surgery requires forethought and desire. Success mandates honesty, discipline, opportunity, and support. This article will attempt to review some fundamental concepts important in starting such an academic career. The thoughts are somewhat personal and not meant to be inclusive. The article will briefly discuss the following issues: choosing the first job, transitions, effective time management, developing clinical confidence, the continued need for mentorship, developing educational value, developing a philosophy of academic growth, intellectual and emotional honesty, myths, mental and physical health, and keys to success. PMID:10727955

  19. AN UNGUIDED TOUR STARTED FROM CHIRALITY

    Institute of Scientific and Technical Information of China (English)

    Jiang Boju; Wang Shicheng

    2009-01-01

    This survey article records an unguided mathematical tour by topologists at Peking University and their collaborators in the last ten years. The tour started from research on chirality and, attracted by questions around attractors, led to a zigzag path across topology and dynamics.People who joined us in this tour at various stages include Ding Fan, Liu Yi, Ni Yi, Pan Jianzhong, Yao Jiangang, Zheng Hao and Zhou Qing. Conversations with Robert Edwards, Wen Lan and others, added to the twists and turns that made the trip more fun.This article benefits from related lectures by these authors, in many conferences, universi-ties, as well as high schools.

  20. Alternative nuclear technologies

    Science.gov (United States)

    Schubert, E.

    1981-10-01

    The lead times required to develop a select group of nuclear fission reactor types and fuel cycles to the point of readiness for full commercialization are compared. Along with lead times, fuel material requirements and comparative costs of producing electric power were estimated. A conservative approach and consistent criteria for all systems were used in estimates of the steps required and the times involved in developing each technology. The impact of the inevitable exhaustion of the low- or reasonable-cost uranium reserves in the United States on the desirability of completing the breeder reactor program, with its favorable long-term result on fission fuel supplies, is discussed. The long times projected to bring the most advanced alternative converter reactor technologies the heavy water reactor and the high-temperature gas-cooled reactor into commercial deployment when compared to the time projected to bring the breeder reactor into equivalent status suggest that the country's best choice is to develop the breeder. The perceived diversion-proliferation problems with the uranium plutonium fuel cycle have workable solutions that can be developed which will enable the use of those materials at substantially reduced levels of diversion risk.

  1. ORGANIZING THE MUSIC CLASSES IN STARTING SCHOOLS

    Directory of Open Access Journals (Sweden)

    N. G. Tagiltseva

    2013-01-01

    Full Text Available The paper considers the issue of children preparation for school in so called starting schools. In author’s opinion, the arts disciplines such as music, drawing and choreography can develop the aesthetic sense, moral qualities, more optimistic world outlook and respectful  attitude; the child develops creative skills and beauty perception both in fine arts and wild life.The author looks at the problems of planning and organizing the music training of preschool children, the different requirements for and concepts of the preschool and primary school normative documents being analyzed. The paper substantiates the effectiveness of poly-artistic and activity approaches to the split-level teaching, in particular – the method of projecting the familiar actions onto some sort of artistic activities. Based on the succession of preschool and primary school training, the author specifies the goals of music classes in starting schools, and outlines the most relevant game activities of role plays, didactic plays and contests.The paper is addressed to preschool and primary school teachers, music teachers, as well as methodologists and researchers dealing with preschool teaching. 

  2. Bauxite slurry pipeline: start up operation

    Energy Technology Data Exchange (ETDEWEB)

    Othon, Otilio; Babosa, Eder; Edvan, Francisco; Brittes, Geraldo; Melo, Gerson; Janir, Joao; Favacho, Orlando; Leao, Marcos; Farias, Obadias [Vale, Rio de Janeiro, RJ (Brazil); Goncalves, Nilton [Anglo Ferrous Brazil S.A., Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The mine of Miltonia is located in Paragominas-PA, in the north of Brazil. Bauxite slurry pipeline starts at the Mine of Miltonia and finishes in the draining installation of Alunorte refinery at the port of Barcarena-PA, located approximately 244km away from the mine. The pipeline runs over seven cities and passes below four great rivers stream beds. The system was designed for an underground 24 inches OD steel pipe to carry 9.9 million dry metric tonnes per annum (dMTAs) of 50.5% solid concentration bauxite slurry, using only one pumping station. The system is composed by four storage tanks and six piston diaphragm pumps, supplying a flow of 1680 m3/h. There is a cathodic protection system along the pipeline extension to prevent external corrosion and five pressure monitoring stations to control hydraulic conditions, there is also a fiber optic cable interconnection between pump station and terminal station. Pipeline Systems Incorporated (PSI) was the designer and followed the commissioning program of the start up operations. This paper will describe the beginning of the pipeline operations, technical aspects of the project, the operational experiences acquired in these two years, the faced problems and also the future planning. (author)

  3. Giving start-ups a helping hand

    CERN Multimedia

    2008-01-01

    The French-Swiss foundation for research and technology (FFSRT) joined forces with CERN to organise an information day on setting up new businesses, at the Globe of Science and Innovation. The participants heard talks by entrepreneurs who started out at CERN, sharing their experiences and difficulties.CERN is a hot-bed of high-tech skills and know-how, and the Organization works actively to transfer this expertise to society. Some such innovations can lead to new business start-ups, but it can be extremely difficult to obtain the information and support you need to find your way through the inevitable administrative labyrinth. By opening its doors to the Fondation franco-suisse pour la recherche et la technologie (FFSRT) and hosting this "Entrepreneurial Day" on 7 March, CERN has clearly flagged its desire to assist budding entrepreneurs. The day was jointly kicked off by Olga Hooft, General Manager of the FFSRT, and Maximilian Metzger, CERN’s Se...

  4. LHC Report: Rocky re-start

    CERN Multimedia

    Barbara Holzer for the LHC Team

    2012-01-01

    A rocky re-start with beam followed a successful machine development period and the first technical stop of 2012. Today, Friday 11 May, the machine began running again with 1380 bunches.   A short, two-day machine development period was successfully completed on 21-22 April. It focused on topics relevant for the 2012 physics beam operation. This was then followed by a five-day technical stop, the first of the year. The technical stop finished on time on Friday 26 April. The re-start with beam was somewhat tortuous and hampered by an unlucky succession of technical faults leading to extended periods of downtime. The planned intensity increase was put on hold for three days with the machine operating with 1092 bunches and a moderate bunch intensity of 1.3x1011 protons. This delivered a reasonable peak luminosity of 3.6x1033 cm-2s-1 to ATLAS and CMS. Higher than usual beam losses were observed in the ramp and squeeze, and time was required to investigate the causes and to implement mitigati...

  5. Revisiting the solar hydrogen alternative

    Energy Technology Data Exchange (ETDEWEB)

    Tomkiewicz, M. [Brooklyn College of CUNY, NY (United States)

    1996-09-01

    Research aimed at the development of technology to advance the solar-hydrogen alternative is per definition mission oriented. The priority that society puts on such research rise and fall with the priorities that we associate with the mission. The mission that we associate with the hydrogen economy is to provide a technological option for an indefinitely sustainable energy and material economies in which society is in equilibrium with its environment. In this paper we try to examine some global aspects of the hydrogen alternative and recommend formulation of a {open_quotes}rational{close_quotes} tax and regulatory system that is based on efforts needed to restore the ecological balance. Such a system, once entered into the price structure of the alternative energy schemes, will be used as a standard to compare energy systems that in turn will serve as a base for prioritization of publicly supported research and development.

  6. Promoting Academic and Social-Emotional School Readiness: The Head Start REDI Program

    OpenAIRE

    Bierman, Karen L.; Domitrovich, Celene E.; Nix, Robert L.; Gest, Scott D.; Welsh, Janet A.; Greenberg, Mark T.; BLAIR, CLANCY; Nelson, Keith E.; Gill, Sukhdeep

    2008-01-01

    Forty-four Head Start classrooms were randomly assigned to enriched intervention (Head Start REDI- Research-based, Developmentally Informed) or “usual practice” conditions. The intervention involved brief lessons, “hands on” extension activities, and specific teaching strategies linked empirically with the promotion of: 1) social-emotional competencies, and 2) language development and emergent literacy skills. Take-home materials were provided to parents to enhance skill development at home. ...

  7. Biomechanical analysis of different starting strategies utilized during cross-country skiing starts.

    Science.gov (United States)

    Wiltmann, Victor Wennemar; Holmberg, Hans-Christer; Pelttari, Pasi; Mikkola, Jussi; Häkkinen, Keijo; Ohtonen, Olli; Linnamo, Vesa

    2016-11-01

    The present study was designed to analyse and compare the kinetics and kinematics associated with three different starting strategies during classic cross-country ski racing. Inside a ski tunnel, 12 elite male skiers performed three sets of three 38 m starts. Each set included one start using: double poling only (DP), diagonal stride only (DIA) and freely chosen (FREE) (i.e. where subjects used the strategy or combination of strategies they felt was fastest) in random order. The first 18 m was performed on a series of force plates that measured horizontal and vertical forces followed by 20 m of a standard snow track. Additionally, cycle characteristics and joint angles were measured. DIA and FREE were faster over 38 m than DP (P skied faster when using only DIA for the entire 38 m. Furthermore, the sum duration and frequency of propulsive contacts over the first 18 m was less in DP than DIA and FREE (P < .01). In conclusion, differences between the starting strategies examined was especially pronounced during the initial cycles. Transition from DIA to DP during the start also slowed the skiers, but optimal timing for such a transition was not elucidated.

  8. Getting started with LevelDB

    CERN Document Server

    Dent, Andy

    2013-01-01

    The book is a concise guide for using LevelDB. It explains database concepts and the use of C++, ranging from the basics all the way to high level topics in an easy to follow, step-by-step format.The book is meant for developers who want an embedded database for their applications. Experienced programmers can pick up on the sophisticated data mapping patterns and tuning tips.Getting Started with LevelDB requires a minimal background in programming in C++ or Objective-C for OS/X or iOS and familiarity with XCode. Therefore it teaches enough C++ to use LevelDB without presuming any C++ knowledge

  9. The UK sugar tax - a healthy start?

    Science.gov (United States)

    Jones, C M

    2016-07-22

    The unexpected announcement by the UK Chancellor of the Exchequer of a levy on sugar sweetened beverages (SSBs) on the 16 March 2016, should be welcomed by all health professionals. This population based, structural intervention sends a strong message that there is no place for carbonated drinks, neither sugared nor sugar-free, in a healthy diet and the proposed levy has the potential to contribute to both general and dental health. The sugar content of drinks exempt from the proposed sugar levy will still cause tooth decay. Improving the proposed tax could involve a change to a scaled volumetric tax of added sugar with a lower exemption threshold. External influences such as the Common Agricultural Policy and the Transatlantic Trade and Investment Partnership may negate the benefits of the sugar levy unless it is improved. However, the proposed UK sugar tax should be considered as a start in improving the nation's diet.

  10. Re-starting an Arnoldi iteration

    Energy Technology Data Exchange (ETDEWEB)

    Lehoucq, R.B. [Argonne National Lab., IL (United States)

    1996-12-31

    The Arnoldi iteration is an efficient procedure for approximating a subset of the eigensystem of a large sparse n x n matrix A. The iteration produces a partial orthogonal reduction of A into an upper Hessenberg matrix H{sub m} of order m. The eigenvalues of this small matrix H{sub m} are used to approximate a subset of the eigenvalues of the large matrix A. The eigenvalues of H{sub m} improve as estimates to those of A as m increases. Unfortunately, so does the cost and storage of the reduction. The idea of re-starting the Arnoldi iteration is motivated by the prohibitive cost associated with building a large factorization.

  11. Antec starts serial production; Antec startet Serienfertigung

    Energy Technology Data Exchange (ETDEWEB)

    Iken, J.

    2001-01-12

    Thuringian producer Antec Solar has produced CdTe modules to near maturity. Serial production is envisaged for January 2001. The CdTe modules will be marketed under the name ATF (Advanced Thin Film Technology). Full production capacityis expected for mid-2002. [German] Die Fertigung von Cadmium-Tellurid-Modulen (CdTe) beim thueringischen Unternehmen Antec Solar steht vor der Serienreife. Die Nullserie wurde Anfang November gestartet und erfolgreich abgeschlossen: 'Die Produktion ist angelaufen, die ersten Module sind gefertigt'. Der Start der Serienproduktion ist fuer Anfang Januar 2001 vorgesehen. Die volle Produktionskapazitaet fuer die CdTe-Module, die Antec unter dem Namen ATF (Advanced Thin Film Technology) vermarkten will, soll Mitte naechsten Jahres erreicht werden. (orig./AKF)

  12. Licensing woes peril start of oil ports

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, E.

    1976-10-04

    Port facility licensing problems are now threatening the planned daily importation of 3.8 million barrels of crude oil through the Gulf of Mexico - oil which could be up to 15 cents cheaper per barrel and provide partial relief to states affected by Canada's impending shutoff of crude exports. Action was expected by December, 1976 on two Gulf Coast deepwater ports - Seadock, Inc. and Louisiana Oil Port, Inc. (LOOP). Oil from both group's proposed facilities could reach Northern-Tier states via existing pipelines. Seadock is planned in the Gulf, 26 miles south of Freeport, Texas and LOOP is to be situated 18 miles off the Louisiana coast directly south of New Orleans. The LOOP crude could be delivered to a St. James, Louisiana pipeline, extending to Patoka, Ill., starting point for other pipelines. (MCW)

  13. The UK sugar tax - a healthy start?

    Science.gov (United States)

    Jones, C M

    2016-07-22

    The unexpected announcement by the UK Chancellor of the Exchequer of a levy on sugar sweetened beverages (SSBs) on the 16 March 2016, should be welcomed by all health professionals. This population based, structural intervention sends a strong message that there is no place for carbonated drinks, neither sugared nor sugar-free, in a healthy diet and the proposed levy has the potential to contribute to both general and dental health. The sugar content of drinks exempt from the proposed sugar levy will still cause tooth decay. Improving the proposed tax could involve a change to a scaled volumetric tax of added sugar with a lower exemption threshold. External influences such as the Common Agricultural Policy and the Transatlantic Trade and Investment Partnership may negate the benefits of the sugar levy unless it is improved. However, the proposed UK sugar tax should be considered as a start in improving the nation's diet. PMID:27444594

  14. When does a sung tone start?

    Science.gov (United States)

    Sundberg, Johan; Bauer-Huppmann, Julia

    2007-05-01

    Although the consonant is mostly considered as the start of a syllable in phonetics and orthography, musicians generally agree that the vowel onset in singing should be synchronized with the beat. As a test of this assumption, the current investigation analyzes the time interval between vowel onsets and piano accompaniment onsets in a set of songs performed by international vocal artists and published on commercial CD recordings. The results show that, most commonly, the accompanists synchronized their tones with the singers' vowel onsets. Nevertheless, examples of lead and lag were found, probably made for expressive purposes. The lead and lag varied greatly between songs, being smallest in a song performed in a fast tempo and longest in a song performed in a slow tempo. PMID:16564674

  15. Start-up Strategy for Continuous Bioreactors

    Directory of Open Access Journals (Sweden)

    A.C. da Costa

    1997-06-01

    Full Text Available Abstract - The start-up of continuous bioreactors is solved as an optimal control problem. The choice of the dilution rate as the control variable reduces the dimension of the system by making the use of the global balance equation unnecessary for the solution of the optimization problem. Therefore, for systems described by four or less mass balance equations, it is always possible to obtain an analytical expression for the singular arc as a function of only the state variables. The steady state conditions are shown to satisfy the singular arc expression and, based on this knowledge, a feeding strategy is proposed which leads the reactor from an initial state to the steady state of maximum productivity

  16. NCAW feed chemistry: Effect of starting chemistry on melter offgas and iron redox

    International Nuclear Information System (INIS)

    The Pacific Northwest Laboratory (PNL) Vitrification Technology Development (PVTD) program has been established to develop technology to support immobilization of selected Hanford wastes. The effort of the PVTD program is directed by the U.S. Department of Energy (DOE). This report is part of the effort and focuses on the effect of starting waste chemistry on the vitrification process. The objective of the investigation was the evaluation of the effect of starting chemistry on the cold cap behavior in the vitrification of simulated neutralized current acid waste (NCAW). In addition this investigation provides an initial laboratory investigation of the cold cap and method for evaluation of alternate reductants

  17. NCAW feed chemistry: Effect of starting chemistry on melter offgas and iron redox

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P.A.; Vienna, J.D.; Merz, M.D.

    1995-03-01

    The Pacific Northwest Laboratory (PNL) Vitrification Technology Development (PVTD) program has been established to develop technology to support immobilization of selected Hanford wastes. The effort of the PVTD program is directed by the U.S. Department of Energy (DOE). This report is part of the effort and focuses on the effect of starting waste chemistry on the vitrification process. The objective of the investigation was the evaluation of the effect of starting chemistry on the cold cap behavior in the vitrification of simulated neutralized current acid waste (NCAW). In addition this investigation provides an initial laboratory investigation of the cold cap and method for evaluation of alternate reductants.

  18. Hydrogen energy network start-up scenario

    International Nuclear Information System (INIS)

    Hydrogen is widely discussed as future fuel and energy storage medium either to replace conventional fuels for automobiles, aircrafts and ships or to avoid the necessity of bulky battery systems for electricity storage, especially in connection with solar power systems. These discussions however started more than 25 years ago and up to now hydrogen has failed to achieve a major break-through towards wider application as energy storage medium in civil markets. The main reason is that other fuels are cheaper and very well implemented in our daily life. A study has been performed at Deutsche Aerospace in order to evaluate the boundary conditions, either political or economical, which would give hydrogen the necessary push, i.e. advantage over conventional fuels. The main goal of this study was to identify critical influence factors and specific start-up scenarios which would allow an economical and practically realistic use of hydrogen as fuel and energy medium in certain niche markets outside the space industry. Method and major results of this study are presented in detail in the paper. Certain niche markets could be identified, where with little initial governmental support, either by funding, tax laws or legislation, hydrogen can compete with conventional fuels. This however requires a scenario where a lot of small actions have to be taken by a high variety of institutions and industries which today are not interconnected with each other, i.e. it requires a new cooperative and proactive network between e.g. energy utilities, car industries, those who have a sound experience with hydrogen (space industry, chemical industry) and last, but certainly not the least, the government. Based on the developed scenario precise recommendations are drawn as conclusions

  19. 46 CFR 112.50-3 - Hydraulic starting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hydraulic starting. 112.50-3 Section 112.50-3 Shipping... POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-3 Hydraulic starting. A hydraulic starting system must meet the following: (a) The hydraulic starting system must be...

  20. Complementary and Alternative Medicine

    Science.gov (United States)

    ... Help a Friend Who Cuts? Complementary and Alternative Medicine KidsHealth > For Teens > Complementary and Alternative Medicine Print ... replacement. continue How Is CAM Different From Conventional Medicine? Conventional medicine is based on scientific knowledge of ...

  1. Alternative medicine - pain relief

    Science.gov (United States)

    Alternative medicine refers to treatments that are used instead of conventional (standard) ones. If you use an alternative ... considered complementary therapy. There are many forms of ... Acupuncture involves stimulating certain acupoints on the body ...

  2. China starts largest ever paleoanthropology project

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ China is believed to be a country especially endowed with the fossils and materials related to early human evolution, next only to the African continent in terms of fecundity and systematism. These materials, including physical and cultural remains of huminids, their associated fauna and flora as well as prehistoric sites, are essential for probing the human origin and evolution. Yet, experts say that the studies of these fossils and artefacts are far from being adequate and perfect in China because they have been plagued by many weak points.

  3. Alternatives to traditional transportation fuels 1994. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this report, alternative and replacement fuels are defined in accordance with the EPACT. Section 301 of the EPACT defines alternative fuels as: methanol, denatured ethanol, and other alcohols; mixtures containing 85% or more (or such other percentage, but not less than 70%, as determined by the Secretary of Energy, by rule, to provide for requirements relating to cold start, safety, or vehicle functions) by volume of methanol, denatured ethanol, and other alcohols with gasoline or other fuels; natural gas; liquefied petroleum gas; hydrogen; coal-derived liquid fuels; fuels (other than alcohol) derived from biological materials; electricity (including electricity from solar energy); and any other fuel the Secretary determines, by rule, is substantially not petroleum and would yield substantial energy security benefits and substantial environmental benefits. The EPACT defines replacement fuels as the portion of any motor fuel that is methanol, ethanol, or other alcohols, natural gas, liquefied petroleum gas, hydrogen, coal-derived liquid fuels, fuels (other than alcohol) derived from biological materials, electricity (including electricity from solar energy), ethers, or any other fuel the Secretary of Energy determines, by rule, is substantially not petroleum and would yield substantial energy security benefits and substantial environmental benefits. This report covers only those alternative and replacement fuels cited in the EPACT that are currently commercially available or produced in significant quantities for vehicle demonstration purposes. Information about other fuels, such as hydrogen and biodiesel, will be included in later reports as those fuels become more widely used. Annual data are presented for 1992 to 1996. Data for 1996 are based on plans or projections for 1996.

  4. 4 Steps to Getting Started with OER

    Science.gov (United States)

    Fasimpaur, Karen

    2012-01-01

    Digital text, changes in textbook adoptions, 1-to-1 computing, Common Core standards, the rise in digital learning objects and online curricula, the push for personalized learning--all of these and other factors are part of an ongoing drama in education today that puts the future of curriculum materials very much in play. But thanks to open…

  5. Substantially isotactic, linear, alternating copolymers of carbon monoxide and an olefin

    Science.gov (United States)

    Sen, Ayusman; Jiang, Zhaozhong

    1996-01-01

    The compound, [Pd(Me-DUPHOS)(MeCN).sub.2 ](BF.sub.4).sub.2, [Me-DUPHOS: 1,2-bis(2,5-dimethylphospholano)benzene] is an effective catalyst for the highly enantioselective, alternating copolymerization of olefins, such as aliphatic .alpha.-olefins, with carbon monoxide to form optically active, isotactic polymers which can serve as excellent starting materials for the synthesis of other classes of chiral polymers. For example, the complete reduction of a propylene-carbon monoxide copolymer resulted in the formation of a novel, optically active poly(1,4-alcohol). Also, the previously described catalyst is a catalyst for the novel alternating isomerization cooligomerization of 2-butene with carbon monoxide to form optically active, isotactic poly(1,5-ketone)

  6. Extended Deterrence, Nuclear Proliferation, and START III

    Energy Technology Data Exchange (ETDEWEB)

    Speed, R.D.

    2000-06-20

    Early in the Cold War, the United States adopted a policy of ''extended nuclear deterrence'' to protect its allies by threatening a nuclear strike against any state that attacks these allies. This threat can (in principle) be used to try to deter an enemy attack using conventional weapons or one using nuclear, chemical, or biological weapons. The credibility of a nuclear threat has long been subject to debate and is dependent on many complex geopolitical factors, not the least of which is the military capabilities of the opposing sides. The ending of the Cold War has led to a significant decrease in the number of strategic nuclear weapons deployed by the United States and Russia. START II, which was recently ratified by the Russian Duma, will (if implemented) reduce the number deployed strategic nuclear weapons on each side to 3500, compared to a level of over 11,000 at the end of the Cold War in 1991. The tentative limit established by Presidents Clinton and Yeltsin for START III would reduce the strategic force level to 2000-2500. However, the Russians (along with a number of arms control advocates) now argue that the level should be reduced even further--to 1500 warheads or less. The conventional view is that ''deep cuts'' in nuclear weapons are necessary to discourage nuclear proliferation. Thus, as part of the bargain to get the non-nuclear states to agree to the renewal of the Nuclear Non-Proliferation Treaty, the United States pledged to work towards greater reductions in strategic forces. Without movement in the direction of deep cuts, it is thought by many analysts that some countries may decide to build their own nuclear weapons. Indeed, this was part of the rationale India used to justify its own nuclear weapons program. However, there is also some concern that deep cuts (to 1500 or lower) in the U.S. strategic nuclear arsenal could have the opposite effect. The fear is that such cuts might undermine extended

  7. Pushed or Pulled? Exploring the Factors Underpinning Graduate Start-Ups and Non-Start-Ups

    Science.gov (United States)

    Nabi, G.; Walmsley, A.; Holden, R.

    2015-01-01

    The study explores the nature and mixture of push--pull factors in the journey from higher education into graduate entrepreneurship. Using longitudinal data from 15 graduates of a British university, it compares graduates who started their own business with graduates that did not. Importantly, both groups had initially indicated a strong desire to…

  8. National Head Start Association Position Paper: Why Conservatives Should Support Head Start.

    Science.gov (United States)

    Allen, Ben; Greene, Sarah; McGrady, Michael; Boel, Bridget; Ryan, Joel; Whitehead, Diane; Smith, Angela; Kane, Elizabeth; Qualls, Brocklin; Wahid, Kahree

    Head Start is a comprehensive federal preschool program, serving children prenatal through age 5 and their families with the overall goal of increasing the school readiness of young children in low-income families. Noting that the program has typically garnered strong support from political liberals and moderates, this position paper of the…

  9. Spreading continents kick-started plate tectonics.

    Science.gov (United States)

    Rey, Patrice F; Coltice, Nicolas; Flament, Nicolas

    2014-09-18

    Stresses acting on cold, thick and negatively buoyant oceanic lithosphere are thought to be crucial to the initiation of subduction and the operation of plate tectonics, which characterizes the present-day geodynamics of the Earth. Because the Earth's interior was hotter in the Archaean eon, the oceanic crust may have been thicker, thereby making the oceanic lithosphere more buoyant than at present, and whether subduction and plate tectonics occurred during this time is ambiguous, both in the geological record and in geodynamic models. Here we show that because the oceanic crust was thick and buoyant, early continents may have produced intra-lithospheric gravitational stresses large enough to drive their gravitational spreading, to initiate subduction at their margins and to trigger episodes of subduction. Our model predicts the co-occurrence of deep to progressively shallower mafic volcanics and arc magmatism within continents in a self-consistent geodynamic framework, explaining the enigmatic multimodal volcanism and tectonic record of Archaean cratons. Moreover, our model predicts a petrological stratification and tectonic structure of the sub-continental lithospheric mantle, two predictions that are consistent with xenolith and seismic studies, respectively, and consistent with the existence of a mid-lithospheric seismic discontinuity. The slow gravitational collapse of early continents could have kick-started transient episodes of plate tectonics until, as the Earth's interior cooled and oceanic lithosphere became heavier, plate tectonics became self-sustaining. PMID:25230662

  10. Rehabilitation starts in the intensive care unit.

    Science.gov (United States)

    Rozeboom, Nathan; Parenteau, Kathy; Carratturo, Daniel

    2012-01-01

    Each year between 10 000 and 12 000 spinal cord injuries occur in the United States. Once injured, many of these patients will receive a portion of their care in an intensive care unit (ICU), where their treatment will begin. Harborview Medical Center in Seattle, Washington, provides comprehensive care to approximately 60 to 70 cervical spinal cord injuries each year. Because of many factors such as hemodynamic instability, pulmonary complications, and risk of infection, patients with cervical spinal cord injuries can spend up to 2 or more weeks in the ICU before they transfer to a rehabilitation unit. To achieve optimal outcomes, it is imperative that members of the interdisciplinary team work together in a consistent, goal-oriented, collaborative manner. This team includes physicians, nurses, respiratory therapists, physical and occupational therapists, speech pathologists, dieticians, and rehabilitation psychologists. An individual plan is developed for each patient and rehabilitation starts in the ICU as soon as the patient is medically stable. This article will highlight the management strategies used in the neuroscience ICU at Harborview Medical Center and will include a case study as an example of the typical experience for our patients with high cervical cord injury.

  11. Spreading continents kick-started plate tectonics.

    Science.gov (United States)

    Rey, Patrice F; Coltice, Nicolas; Flament, Nicolas

    2014-09-18

    Stresses acting on cold, thick and negatively buoyant oceanic lithosphere are thought to be crucial to the initiation of subduction and the operation of plate tectonics, which characterizes the present-day geodynamics of the Earth. Because the Earth's interior was hotter in the Archaean eon, the oceanic crust may have been thicker, thereby making the oceanic lithosphere more buoyant than at present, and whether subduction and plate tectonics occurred during this time is ambiguous, both in the geological record and in geodynamic models. Here we show that because the oceanic crust was thick and buoyant, early continents may have produced intra-lithospheric gravitational stresses large enough to drive their gravitational spreading, to initiate subduction at their margins and to trigger episodes of subduction. Our model predicts the co-occurrence of deep to progressively shallower mafic volcanics and arc magmatism within continents in a self-consistent geodynamic framework, explaining the enigmatic multimodal volcanism and tectonic record of Archaean cratons. Moreover, our model predicts a petrological stratification and tectonic structure of the sub-continental lithospheric mantle, two predictions that are consistent with xenolith and seismic studies, respectively, and consistent with the existence of a mid-lithospheric seismic discontinuity. The slow gravitational collapse of early continents could have kick-started transient episodes of plate tectonics until, as the Earth's interior cooled and oceanic lithosphere became heavier, plate tectonics became self-sustaining.

  12. The GlueX Start Counter

    Science.gov (United States)

    Pooser, Eric; GlueX Collaboration

    2013-10-01

    The GlueX experiment will be one of the largest photo-production facilities in the world and is currently under construction. This experiment will use the coherent bremsstrahlung technique to produce a 9 GeV linearly polarized photon beam incident on a liquid H2 target. A Start Counter detector has been designed to identify the accelerator electron beam buckets, approximately 2 ns apart, and to provide accurate timing information. It is now under construction at Florida International University (FIU). This detector is designed to operate at photon intensities of up to 108 γ /s in the coherent peak. It consists of an array of 30 individual scintillators with ``pointed'' ends that bend toward the beam at the downstream end. SiPM detectors, which comprise the readout system, are placed as close as possible at the end of each scintillator. The EJ-200 scintillator is best suited for the timing studies with a fast decay time of 2.0 ns. The physical properties of the scintillators, configured to the desired geometry, have been studied extensively at FIU. Geant4 simulations are currently underway to replicate and to understand our experimental results. The results of these timing studies and simulations are discussed.

  13. Equilibrium reconstruction in the START tokamak

    Science.gov (United States)

    Appel, L. C.; Bevir, M. K.; Walsh, M. J.

    2001-02-01

    The computation of magnetic equilibria in the START spherical tokamak is more difficult than those in more conventional large aspect ratio tokamaks. This difficulty arises partly as a result of the use of induction compression to generate high current plasma, as this precludes the positioning of magnetic diagnostics close to the outboard side of the plasma. In addition, the effect of a conducting wall with a high, but finite, conductivity must be included. A method is presented for obtaining plasma equilibrium reconstructions based on the EFIT code. New constraints are used to relate isoflux surface locations deduced from radial profile measurements of electron temperature. A model of flux diffusion through the vessel wall is developed. It is shown that neglecting flux diffusion in the vessel wall can lead to a significant underestimate in the calculation of the plasma βt. Using a relatively sparse set of magnetic signals, βt can be obtained to within a fractional error of +/-10%. Using constraints to relate isoflux surface locations, the principle involved in determining the internal q profile is demonstrated.

  14. Measured moisture properties for alternative insulation products

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Hansen, Kurt Kielsgaard; Padfield, Tim

    1999-01-01

    During the past few years there has been a growing interest in using alternative insulation products in buildings. Among these products are the organic materials cellulose fibre, flax and sheep's wool as well as the inorganic perlite. The organic materials are regarded with some suspicion, because...

  15. Training Materials Developed for Latino Entrepreneurs

    Science.gov (United States)

    Abreo, Christina; Miller, Wayne; Farmer, Frank; Moon, Zola; McCullough, Stacey

    2014-01-01

    This article describes the materials and training program that Extension created to assist current and potential Latino immigrant entrepreneurs in starting businesses in Arkansas. The content-based educational materials describe the process for starting a new business, government regulatory requirements, start-up costs and considerations, and how…

  16. Utopian Materialities

    DEFF Research Database (Denmark)

    Elgaard-Jensen, Torben

    2004-01-01

    In various ways, this paper makes the counter-intuitive claim that the utopian and the material are thoroughlyinterdependent, rather than worlds apart. First, through a reading of Thomas More's Utopia, it is argued thatUtopia is the product of particular kinds of relations, rather than merely a...... detachment from the known world.Second, the utopianism of a new economy firm is examined. It is argued that the physical set-up of the firm -in particular the distribution of tables and chairs - evoke a number of alternatives to ordinary work practice.In this way the materialities of the firm are crucial to...... its persuasive image of being the office of the future.The notion that utopia is achieved through material arrangements is finally related to the analysis of facts andfictions in ANT. It is argued, that even though Utopias are neither fact nor fiction, they are both material andeffective on the...

  17. Effect of starting stance on initial sprint performance.

    Science.gov (United States)

    Cronin, John B; Green, Jonathon P; Levin, Gregory T; Brughelli, Matt E; Frost, David M

    2007-08-01

    The effect of different starting stances from a standing position on short sprint times and the subsequent variability in times was investigated in this study. A dual-beam timing light system was used to measure 5- and 10-m times for 3 different standing starts commonly found in the sporting environment: parallel (feet parallel to the start line), split (lead left foot on start line, right leg back), and false (initial parallel start, right leg drops back to split start when movement initiated). The parallel start was found to be significantly (alpha men and women. The split and false start seem to offer the best option as a movement strategy for minimizing short-distance sprint times. However, the benefits of these 2 starts are less clear if total movement time is the variable of interest.

  18. On electrode erosion in fluorescent lamps during instant start

    Energy Technology Data Exchange (ETDEWEB)

    Hadrath, S.

    2006-09-15

    A fluorescent lamp driven with an 'instant start electronic control gear' starts in a glow mode. In the glow mode, which lasts typically for tens of milliseconds, the cathode fall exceeds hundreds of volts. This causes high energy ion bombardment of the electrode which heats the electrode, and induces a transition from glow to arc mode. In the arc mode the electrode emits thermionically and the cathode fall drops to the 12 - 15 V range. Unfortunately, the high energy ion bombardment during the glow mode leads also to intense sputtering of electrode material, including tungsten as well as emitter. Thus, instant started fluorescent lamps often suffer from early failures due to coil fracture. Therefore, the investigation of tungsten erosion during instant start is necessary and was the main goal of this work. The density of neutral atomic tungsten is determined by laser-induced fluorescence (LIF) and optical emission spectroscopy measurements (OES). Investigations are performed on a low-pressure argon dc discharge and on commercial fluorescent lamps. To include the entire temperature profile along the electrode the diffuse and spot operation modes of the dc lamp are studied experimentally and theoretically. The measured dependencies of the cathode temperature along the coil on the discharge and heating parameters are compared with the calculated results. For the first time the tungsten erosion during instant start of commercial fluorescent lamps was experimentally investigated in this work. The erosion process could be related to sputtering. A reconstruction of the temporal evolution of the absolute tungsten population density of the ground state during the glow mode was presented. The sputtered tungsten density increases immediately with the ignition, reaches a maximum where the discharge contracts at the end of the glow mode, and decreases some milliseconds before the glow-to-arc transition takes place. The maximum tungsten density was observed within a

  19. Study on Undertaking-starting of New Generation Migrant Workers

    Institute of Scientific and Technical Information of China (English)

    Chuang; LU; Wanzhao; LIU

    2014-01-01

    New generation migrant workers have become mainstay of China’s migrant workers and also major builders of China’s urbanization process. Compared with last generation migrant workers,new generation migrant workers have greater awareness of starting an undertaking. In the new trend,undertaking-starting is inevitable for new generation migrant workers. This study analyzed problems encountered by new generation migrant workers in the course of starting an undertaking. It reached conclusions that competent authorities should set up support mechanism in undertaking-starting training,undertaking-starting fund,service platform,and preferential policies,to encourage and support new generation migrant workers to start an undertaking.

  20. Starting up microbial enhanced oil recovery.

    Science.gov (United States)

    Siegert, Michael; Sitte, Jana; Galushko, Alexander; Krüger, Martin

    2014-01-01

    This chapter gives the reader a practical introduction into microbial enhanced oil recovery (MEOR) including the microbial production of natural gas from oil. Decision makers who consider the use of one of these technologies are provided with the required scientific background as well as with practical advice for upgrading an existing laboratory in order to conduct microbiological experiments. We believe that the conversion of residual oil into natural gas (methane) and the in situ production of biosurfactants are the most promising approaches for MEOR and therefore focus on these topics. Moreover, we give an introduction to the microbiology of oilfields and demonstrate that in situ microorganisms as well as injected cultures can help displace unrecoverable oil in place (OIP). After an initial research phase, the enhanced oil recovery (EOR) manager must decide whether MEOR would be economical. MEOR generally improves oil production but the increment may not justify the investment. Therefore, we provide a brief economical assessment at the end of this chapter. We describe the necessary state-of-the-art scientific equipment to guide EOR managers towards an appropriate MEOR strategy. Because it is inevitable to characterize the microbial community of an oilfield that should be treated using MEOR techniques, we describe three complementary start-up approaches. These are: (i) culturing methods, (ii) the characterization of microbial communities and possible bio-geochemical pathways by using molecular biology methods, and (iii) interfacial tension measurements. In conclusion, we hope that this chapter will facilitate a decision on whether to launch MEOR activities. We also provide an update on relevant literature for experienced MEOR researchers and oilfield operators. Microbiologists will learn about basic principles of interface physics needed to study the impact of microorganisms living on oil droplets. Last but not least, students and technicians trying to understand

  1. Abscisic Acid Signal off the STARTing Block

    Institute of Scientific and Technical Information of China (English)

    Archana Joshi-Saha; Christiane Valon; Jeffrey Leung

    2011-01-01

    The year 2009 marked a real turnaround in our understanding of the mode ot abscisJc acid(ABA)action. Nearly 25 years had elapsed since the first biochemical detection of ABA-binding proteins in the plasmalemma of Vicia guard cells was reported. This recent-and laudable-achievement is owed largely to the discovery of the soluble ABA receptors whose major interacting proteins happen to be some of the most well-established components of earliest steps in ABA signaling. These soluble receptors, with the double name of PYRABACTIN RESISTANCE (PYR)or REGULATORY COM-PONENT OF ABA RECEPTOR (RCAR), are a family of Arabidopsis proteins of about 150-200 amino acids that share a con-served START domain. The ABA signal transduction circuitry under non-stress conditions is muted by the ciade A protein phosphatases 2C (PP2C)(notably HAB1, ABI1, and ABI2). During the initial steps of ABA signaling, the binding of the hor-mone to the receptor induces a conformational change in the latter that allows it to sequester the PP2Cs. This excludes them from the negative regulation of the downstream ABA-activated kinases (OST1/SnRK2.6/SRK2E, SnRK2.2, and SnRK2.3), thus unleashing the pathway by freeing them to phosphorylate downstream targets that now include several b-ZIP transcription factors, ion channels (SLAC1, KAT1), and a NADPH oxidase (AtrbohF). The discovery of this family of soluble receptors and the rich insight already gained from structural studies of their complexes with different isoforms of ABA, PP2C, and the synthetic agonist pyrabactin lay the foundation towards rational design of chemical switches that can bolster drought hardiness in plants.

  2. Photovoltaic Materials

    Energy Technology Data Exchange (ETDEWEB)

    Duty, C.; Angelini, J.; Armstrong, B.; Bennett, C.; Evans, B.; Jellison, G. E.; Joshi, P.; List, F.; Paranthaman, P.; Parish, C.; Wereszczak, A.

    2012-10-15

    cells and modules in the field for 25 years. Under this project, Ferro leveraged world leading analytical capabilities at ORNL to characterize the paste-to-silicon interface microstructure and develop high efficiency next generation contact pastes. Ampulse Corporation is developing a revolutionary crystalline-silicon (c-Si) thin-film solar photovoltaic (PV) technology. Utilizing uniquely-textured substrates and buffer materials from the Oak Ridge National Laboratory (ORNL), and breakthroughs in Hot-Wire Chemical Vapor Deposition (HW-CVD) techniques in epitaxial silicon developed at the National Renewable Energy Laboratory (NREL), Ampulse is creating a solar technology that is tunable in silicon thickness, and hence in efficiency and economics, to meet the specific requirements of multiple solar PV applications. This project focused on the development of a high rate deposition process to deposit Si, Ge, and Si1-xGex films as an alternate to hot-wire CVD. Mossey Creek Solar is a start-up company with great expertise in the solar field. The primary interest is to create and preserve jobs in the solar sector by developing high-yield, low-cost, high-efficiency solar cells using MSC-patented and -proprietary technologies. The specific goal of this project was to produce large grain formation in thin, net-shape-thickness mc-Si wafers processed with high-purity silicon powder and ORNL's plasma arc lamp melting without introducing impurities that compromise absorption coefficient and carrier lifetime. As part of this project, ORNL also added specific pieces of equipment to enhance our ability to provide unique insight for the solar industry. These capabilities include a moisture barrier measurement system, a combined physical vapor deposition and sputtering system dedicated to cadmium-containing deposits, adeep level transient spectroscopy system useful for identifying defects, an integrating sphere photoluminescence system, and a high-speed ink jet printing system. These

  3. FMDP Reactor Alternative Summary Report: Volume 2 - CANDU heavy water reactor alternative

    International Nuclear Information System (INIS)

    The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 2 of a four volume report, summarizes the results of these analyses for the CANDU reactor based plutonium disposition alternative

  4. FMDP Reactor Alternative Summary Report: Volume 3 - partially complete LWR alternative

    International Nuclear Information System (INIS)

    The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 3 of a four volume report summarizes the results of these analyses for the partially complete LWR (PCLWR) reactor based plutonium disposition alternative

  5. FMDP Reactor Alternative Summary Report: Volume 2 - CANDU heavy water reactor alternative

    Energy Technology Data Exchange (ETDEWEB)

    Greene, S.R.; Spellman, D.J.; Bevard, B.B. [and others

    1996-09-01

    The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 2 of a four volume report, summarizes the results of these analyses for the CANDU reactor based plutonium disposition alternative.

  6. On an Alternative Cosmology

    CERN Document Server

    Vankov, A

    1998-01-01

    The suggested alternative cosmology is based on the idea of barion symmetric universe, in which our home universe is a representative of multitude of typical matter and antimatter universes. This alternative concept gives a physically reasonable explanation of all major problems of the Standard Cosmological Model. Classification Code MSC: Cosmology 524.8 Key words: standard cosmological model, alternative cosmology, barionic symmetry, typical universe, quasars, cosmic rays.

  7. Polyphase alternating codes

    CERN Document Server

    Markkanen, Markku

    2007-01-01

    This work introduces a method for constructing polyphase alternating codes in which the length of a code transmission cycle can be $p^m$ or $p-1$, where $p$ is a prime number and $m$ is a positive integer. The relevant properties leading to the construction alternating codes and the algorithm for generating alternating codes is described. Examples of all practical and some not that practical polyphase code lengths are given.

  8. Alternative Solar Indices

    Energy Technology Data Exchange (ETDEWEB)

    Lantz, L.J.

    1980-07-01

    Possible alternative Solar Indices which could either be a perturbation from the currently defined Solar Index or possible indices based on current technologies for other media markets are discussed. An overview is given of the current project, including the logic that was utilized in defining its current structure and then alternative indices and definitions are presented and finally, recommendations are made for adopting alternative indices.

  9. Complex Alternative Splicing

    OpenAIRE

    Park, Jung Woo; Graveley, Brenton R.

    2007-01-01

    Alternative splicing is a powerful means of controlling gene expression and increasing protein diversity. Most genes express a limited number of mRNA isoforms, but there are several examples of genes that use alternative splicing to generate hundreds, thousands, and even tens of thousands of isoforms. Collectively such genes are considered to undergo complex alternative splicing. The best example is the Drosophila Down syndrome cell adhesion molecule (Dscam) gene, which can generate 38,016 is...

  10. First results from the start up at pilot plant Niederaussem

    Energy Technology Data Exchange (ETDEWEB)

    Moser, P.; Schmidt, S. [RWE Power, Essen (Germany); Garcia, H.; Sieder, G. [BASF SE (Germany); Forster, C.; Stoffregen, T. [Linde-KCA Dresden GmbH (Germany)

    2009-07-01

    In 2007, RWE Power, BASF and Linde entered into a cooperation to adapt carbon dioxide (CO{sub 2}) scrubbing technology for use in power plants and to optimize the techno-economical performance of CO{sub 2} post combustion capture. The project involved the construction of a new pilot plant at RWE Power's lignite-fired power plant in Niederaussem, Germany to investigate all aspects of the capture process with regards to a new energy-efficient solvent developed by BASF and the improved plant technology by Linde. Approximately 250 measurements and online-analysis systems were used to validate the operational performance, energy demand for CO{sub 2} capture and solvent stability. The construction of the pilot plant began in October 2008. Commissioning started in May 2009 and the pilot plant was finalized in July 2009. The testing program involves extensive parameter studies as well as a comprehensive material testing program for steels and new construction materials for columns and pipes. This paper presented the first results from the pilot plant operation in which MEA was used as a reference solvent. Technical details of the pilot plant were provided along with the test program for the new advanced solvent.

  11. Pakistan/USAID to start CSM project.

    Science.gov (United States)

    1984-01-01

    Pakistan, with the assistance of funds for the US Agency for International Development (USAID), is about to start its novel approach to contraceptive social marketing (CSM). This new effort suggests a marked policy shift on the part of the Pakistan government toward intensifying its family planning activities. The program will be government-operated and supported by AID over the next 5 years with $20 million, more than double the cost of similar CSM projects elswhere. Distribution of a condom on a pilot project basis is expected to begin by December 1984. Sales of a low-dose oral contraceptive (OC) could begin in test market areas by mid-1985, with national launching of both products tentatively scheduled for January 1986. The Pakistan/USAID agreement represents the 1st time since the formation of India's Nirodh project in the late 1960s that a CSM program is being established without the involvement of either an international social marketing contractor or a country's family planning association. The Pakistan CSM program will be managed by a policy board composed of representatives from the government's Ministries of Planning, Health and Education; a resident advisor from USAID; and a local company responsible for product marketing and distribution. The approach has received a skeptical response among international social marketing experts about the program's chances for success. Their doubts extend to 2 other aspects of the proposed design: an official of the Ministry of Planning's Population and Welfare Division expects the CSM program to generate sufficient revenues to cover all operating costs following the 5-year subsidy period, while also providing attractive profit margins for the marketing/distribution company; and the government prohibits mass media advertising of contraceptives. According to AID, the issue of mass media contraceptive advertising has not yet been resolved, and a national survey will be conducted to determine what communication needs are

  12. 76 FR 17736 - Major Capital Investment Program-New Starts

    Science.gov (United States)

    2011-03-30

    ... Federal Transit Administration Major Capital Investment Program--New Starts AGENCY: Federal Transit... discretionary selection of projects for funding using unallocated Major Capital Investment (New Starts) program... that have made important investments in their transportation infrastructure. ] Furthermore, the...

  13. Síntesis de materiales moleculares a partir de donadores electrónicos orgánicos y aceptores electrónicos inorgánicos. // Synthesis of molecular materials starting from organic electronic donors and inorganic electronic receivers.

    Directory of Open Access Journals (Sweden)

    A. Cázares Sánchez

    2003-09-01

    Full Text Available Los materiales moleculares están formados por un donador electrónico y un aceptor electrónico condensados en una fase.La síntesis de nuevos materiales moleculares se puede realizar por electrosíntesis o por síntesis química convencional. Eneste trabajo se presentan los resultados obtenidos de la síntesis de nuevos materiales moleculares por electrosíntesis a partirde los donadores electrónicos orgánicos: BETS y BEDT; y aceptores electrónicos inorgánicos de fierro y cobalto. Laposibilidad de síntesis de los materiales a partir de los donadores y aceptores utilizados fue analizada con voltametríacíclica; mientras que los materiales fueron caracterizados mediante espectrometría infrarroja (IR y por microscopioelectrónico de barrido (MEB.Palabras claves: Donador electrónico, aceptor electrónico, electrosíntesis, material molecular.____________________________________________________________________________Abstract.Molecular materials are constituted of an electronic donor and an aceptor organized in a condensed phase. A synthetizednew molecular material is posible using electrosynthesis or conventional chemistry synthesis. In this job, we reported theresults to the synthesis of new molecular materials that have been prepared by electrosynthesis from organics electronicsdonors: BETS and BEDT; and inorganics electronics aceptors of iron and cobalt. The possibility to sinthetizes the materialsfrom the donors and aceptors used was analized with ciclic voltametry; while the materials were characteryzed with thehelp of infrared spectrometry and scanning electronic microscopy.Key words: electronic donor, electronic aceptor, electrosynthesis, molecular material.

  14. Personal and Public Start Pages in a library setting

    NARCIS (Netherlands)

    Wondergem, Dorine

    2009-01-01

    Personal and Public Start Pages are web-based resources. With these kind of tools it is possible to make your own free start page. A Start Page allows you to put all your web resources into one page, including blogs, email, podcasts, RSSfeeds. It is possible to share the content of the page with oth

  15. [Complementary and alternative medicine in oncology].

    Science.gov (United States)

    Hübner, J

    2013-06-01

    Complementary and alternative medicine are frequently used by cancer patients. The main benefit of complementary medicine is that it gives patients the chance to become active. Complementary therapy can reduce the side effects of conventional therapy. However, we have to give due consideration to side effects and interactions: the latter being able to reduce the effectiveness of cancer therapy and so to jeopardise the success of therapy. Therefore, complementary therapy should be managed by the oncologist. It is based on a common concept of cancerogenesis with conventional therapy. Complement therapy can be assessed in studies. Alternative medicine in contrast rejects common rules of evidence-based medicine. It starts from its own concepts of cancerogenesis, which is often in line with the thinking of lay persons. Alternative medicine is offered as either "alternative" to recommended cancer treatment or is used at the same time but without due regard for the interactions. Alternative medicine is a high risk to patients. In the following two parts of the article, the most important complementary and alternative therapies cancer patients use nowadays are presented and assessed according to published evidence.

  16. Normetex Pump Alternatives Study

    Energy Technology Data Exchange (ETDEWEB)

    Clark, Elliot A.

    2013-04-25

    A mainstay pump for tritium systems, the Normetex scroll pump, is currently unavailable because the Normetex company went out of business. This pump was an all-metal scroll pump that served tritium processing facilities very well. Current tritium system operators are evaluating replacement pumps for the Normetex pump and for general used in tritium service. An all-metal equivalent alternative to the Normetex pump has not yet been identified. 1. The ideal replacement tritium pump would be hermetically sealed and contain no polymer components or oils. Polymers and oils degrade over time when they contact ionizing radiation. 2. Halogenated polymers (containing fluorine, chlorine, or both) and oils are commonly found in pumps. These materials have many properties that surpass those of hydrocarbon-based polymers and oils, including thermal stability (higher operating temperature) and better chemical resistance. Unfortunately, they are less resistant to degradation from ionizing radiation than hydrocarbon-based materials (in general). 3. Polymers and oils can form gaseous, condensable (HF, TF), liquid, and solid species when exposed to ionizing radiation. For example, halogenated polymers form HF and HCl, which are extremely corrosive upon reaction with water. If a pump containing polymers or oils must be used in a tritium system, the system must be designed to be able to process the unwanted by-products. Design features to mitigate degradation products include filters and chemical or physical traps (eg. cold traps, oil traps). 4. Polymer components can work in tritium systems, but must be replaced regularly. Polymer components performance should be monitored or be regularly tested, and regular replacement of components should be viewed as an expected normal event. A radioactive waste stream must be established to dispose of used polymer components and oil with an approved disposal plan developed based on the facility location and its regulators. Polymers have varying

  17. High-Grade Color Offset Paper of Xinya Paper Group Started Operation Successfully

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    On March 5th, the 3150 mm paper machine of Xinya Paper Group started the operation successfully. Originally, the paper machine produced ordinary culture paper, using mixed straw and wood pulp as the raw material. With the market demand shift toward higher quality, the original products produced can no longer meet the requirements.

  18. (--DRIMENOL – A VALUABLE STARTING COMPOUND FOR THE SYNTHESIS OF DRIMANIC SESQUITERPENOIDS

    Directory of Open Access Journals (Sweden)

    Aculina Aricu

    2009-12-01

    Full Text Available (--Drimenol is a relatively accessible compound, that has been and may be further used as a starting material to prepare sesquiterpenoids. The present review deals with the methods of obtaining of this compound as well as its usage.

  19. Alternative Devices for Taking Insulin

    Science.gov (United States)

    ... KB). Alternate Language URL Alternative Devices for Taking Insulin Page Content On this page: What alternative devices ... the skin. [ Top ] What alternative devices for taking insulin are available? Insulin pens provide a convenient, easy- ...

  20. Alternative health insurance schemes

    DEFF Research Database (Denmark)

    Keiding, Hans; Hansen, Bodil O.

    2002-01-01

    In this paper, we present a simple model of health insurance with asymmetric information, where we compare two alternative ways of organizing the insurance market. Either as a competitive insurance market, where some risks remain uninsured, or as a compulsory scheme, where however, the level...... competitive insurance; this situation turns out to be at least as good as either of the alternatives...

  1. Biomechanical Analysis of the Swim-Start: A Review

    OpenAIRE

    Julien Vantorre, Didier Chollet, Ludovic Seifert

    2014-01-01

    This review updates the swim-start state of the art from a biomechanical standpoint. We review the contribution of the swim-start to overall swimming performance, the effects of various swim-start strategies, and skill effects across the range of swim-start strategies identified in the literature. The main objective is to determine the techniques to focus on in swimming training in the contemporary context of the sport. The phases leading to key temporal events of the swim-start, like water e...

  2. Methods of materiality

    DEFF Research Database (Denmark)

    Aagaard, Jesper; Matthiesen, Noomi

    2016-01-01

    that researchers should start paying attention to the material world (consisting of both human bodies and material objects) and what it means for how people live their lives. It is argued that this can be done by incorporating the concept of material presence to capture embodied and material layers of existence......, and the method of participant observation is suggested as a viable approach to achieve this end. An empirical example of how authority is produced in a parent-teacher conference, not only through language but also through material objects and embodied being, is then presented. The article concludes by suggesting...... practical guidelines for incorporating attention to materiality in qualitative research....

  3. Starting over. Why remarriages are more unstable.

    Science.gov (United States)

    Booth, A; Edwards, J N

    1992-06-01

    Previously divorced and remarried couples have a higher probability of divorce and decline in marital quality. Models which have explained this behavior focus on: willingness to leave marriage; selection; socioeconomic status; the remarriage market; and incomplete marriages. Each model is examined among a population of marrieds and remarrieds to distinguish attributes and the extent to which these attributes increase the probability of decline in marital quality or divorce. Data were obtained from a sample of 2033 marrieds 55 years old who were interviewed over the telephone in 1980, 1983, and 1988 in the Marital Instability Over the Life Course Study. Incomplete marriage was measured by whether and to what extent parents or parents-in-law made contact and the number of relatives that party was close to. Willingness to leave was based on attitudes to divorce and the ability to handle emotion and financial affairs if the marriage ended. Selection referred to poor marriage material (drugs or alcohol, criminal conduct, mismanagement of money, immature behavior. Socioeconomic status was reflected in occupational status, educational levels, and income. The marriage market was a measure of age, education, and religious differences. Marital quality was examined in terms of happiness, interaction, disagreement, and divorce proneness. Multiple classification analysis was used to compare attributes by marital history. The methods of Kessler and Greenberg were used to examine changes in marital quality over time in first time marriages and remarriages. The results indicate that individuals in remarriages have relationships with attributes which potentially lower marital quality and increase the probability of divorce. When both individuals have prior marriage and divorce experience, there is even lower social integration, greater willingness to leave marriage, higher probability of marrying as a teen, lower socioeconomic status, and greater likelihood of age differences

  4. Alternative loop rings

    CERN Document Server

    Goodaire, EG; Polcino Milies, C

    1996-01-01

    For the past ten years, alternative loop rings have intrigued mathematicians from a wide cross-section of modern algebra. As a consequence, the theory of alternative loop rings has grown tremendously. One of the main developments is the complete characterization of loops which have an alternative but not associative, loop ring. Furthermore, there is a very close relationship between the algebraic structures of loop rings and of group rings over 2-groups. Another major topic of research is the study of the unit loop of the integral loop ring. Here the interaction between loop rings and group ri

  5. HL-LHC alternatives

    CERN Document Server

    Tomás, R; White, S

    2014-01-01

    The HL-LHC parameters assume unexplored regimes for hadron colliders in various aspects of accelerator beam dynamics and technology. This paper reviews three alternatives that could potentially improve the LHC performance: (i) the alternative filling scheme 8b+4e, (ii) the use of a 200 MHz RF system in the LHC and (iii) the use of proton cooling methods to reduce the beam emittance (at top energy and at injection). The alternatives are assessed in terms of feasibility, pros and cons, risks versus benefits and the impact on beam availability.

  6. VISTA: Pioneering New Survey Telescope Starts Work

    Science.gov (United States)

    2009-12-01

    A new telescope - VISTA (the Visible and Infrared Survey Telescope for Astronomy) - has just started work at ESO's Paranal Observatory and has made its first release of pictures. VISTA is a survey telescope working at infrared wavelengths and is the world's largest telescope dedicated to mapping the sky. Its large mirror, wide field of view and very sensitive detectors will reveal a completely new view of the southern sky. Spectacular new images of the Flame Nebula, the centre of our Milky Way galaxy and the Fornax Galaxy Cluster show that it is working extremely well. VISTA is the latest telescope to be added to ESO's Paranal Observatory in the Atacama Desert of northern Chile. It is housed on the peak adjacent to the one hosting the ESO Very Large Telescope (VLT) and shares the same exceptional observing conditions. VISTA's main mirror is 4.1 metres across and is the most highly curved mirror of this size and quality ever made - its deviations from a perfect surface are less than a few thousandths of the thickness of a human hair - and its construction and polishing presented formidable challenges. VISTA was conceived and developed by a consortium of 18 universities in the United Kingdom [1] led by Queen Mary, University of London and became an in-kind contribution to ESO as part of the UK's accession agreement. The telescope design and construction were project-managed by the Science and Technology Facilities Council's UK Astronomy Technology Centre (STFC, UK ATC). Provisional acceptance of VISTA was formally granted by ESO at a ceremony at ESO's Headquarters in Garching, Germany, attended by representatives of Queen Mary, University of London and STFC, on 10 December 2009 and the telescope will now be operated by ESO. "VISTA is a unique addition to ESO's observatory on Cerro Paranal. It will play a pioneering role in surveying the southern sky at infrared wavelengths and will find many interesting targets for further study by the Very Large Telescope, ALMA and

  7. Head Start: A True Start to Getting Ahead: A Literature Review of the Head Start Program as a Primary Poverty Prevention Strategy

    Directory of Open Access Journals (Sweden)

    Smith, LaPorsche C.

    2012-10-01

    Full Text Available The federal Head Start Program plays a vital role in increasing the likelihood that under-privileged children will become academically successful in school, attend college, and become successful citizens. Yet, Head Start continuously struggles to retain its funding and is challenged in its goal of assisting low income children. A review of the literature on Head Start and related early childhood education longitudinal studies will attest to the importance of this program as a primary prevention strategy to reduce poverty, raise public awareness of its benefits, and support the efforts of its advocates to retain and expand its funding at local and federal levels.

  8. Evaluation of Expenditure Alternates

    Science.gov (United States)

    Poehlein, Gary W.; And Others

    1973-01-01

    Illustrates a system of calculating dollar expenditures over periods of time in terms of present value. The system enables planners, school boards, and administrators to compare expenditure alternatives as a decisionmaking factor. (Author)

  9. Alternatives to Nursing Homes

    Science.gov (United States)

    ... this website may not be available. Alternatives to nursing homes Before you make any decisions about long ... live and what help you may need. A nursing home may not be your only choice. Discharge ...

  10. Alternative disinfectant water treatments

    Science.gov (United States)

    Alternative disinfestant water treatments are disinfestants not as commonly used by the horticultural industry. Chlorine products that produce hypochlorous acid are the main disinfestants used for treating irrigation water. Chlorine dioxide will be the primary disinfestant discussed as an alternativ...

  11. Vaginal dryness alternative treatments

    Science.gov (United States)

    ... a day. Soybeans contain plant-based substances called isoflavones. These substances have an effect on the body ... soy for vasomotor symptoms: the Herbal Alternatives for Menopause (HALT) Study. Menopause . 2008;15(1):51-58. ...

  12. An alternative currency

    OpenAIRE

    Frendo, Mario; Duca, Edward

    2013-01-01

    Malta- a tiny island, a minute social reality, a precursory canovaccio of European unification- has a unique asset it ought to be prouder of: culture. http://www.um.edu.mt/think/an-alternative-currency/

  13. Alternative fuel information sources

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    This short document contains a list of more than 200 US sources of information (Name, address, phone number, and sometimes contact) related to the use of alternative fuels in automobiles and trucks. Electric-powered cars are also included.

  14. Alternative fuel cycles

    International Nuclear Information System (INIS)

    Uranium resource utilization and economic considerations provide incentives to study alternative fuel cycles as future options to the PHWR natural uranium cycle. Preliminary studies to define the most favourable alternatives and their possible introduction dates are discussed. The important and uncertain components which influence option selection are reviewed, including nuclear capacity growth, uranium availability and demand, economic potential, and required technological developments. Finally, a summary of Ontario Hydro's program to further assess cycle selection and define development needs is given. (auth)

  15. CONSERVATION AREA START-UPS: COMBINING THEORY AND PRACTICE

    OpenAIRE

    NORMAN S. WRIGHT; JEFF CANEEN; NATHAN ALEXANDER; ANDREW GOMEZ

    2010-01-01

    Business start-ups by indigenous people in wildlife conservation areas are prone to failure. Funding issues have been identified as a contributing cause of the disappointing results. A great deal has been written about capital structure both in the start-up literature and the corporate literature, but the applicability of this research to small, indigenous start-ups in and around conservation areas is lacking. Although current practice dictates a reliance on equity, we apply the relevant corp...

  16. Learning in the business start-up process

    OpenAIRE

    Niels Bosma; Joris Meijaard; Gijs van Popta

    2002-01-01

    The start-up process is an important source for learning opportunities. The present study investigates different types of entrepreneurial learning in the start-up process. Combining contributions from psychology, sociology, organisational and entrepreneurship literature, an appropriate conceptual framework emerges, in which different types of entrepreneurial learning are distinguished. Based on this framework, and using panel data on start-up entrepreneurs, we empirically rediscovered this ty...

  17. MICRO ENGINE START PERFORMANCE RESEARCH FOR RACING CAR

    Directory of Open Access Journals (Sweden)

    O. Vrublevskiy

    2015-07-01

    Full Text Available A methodology of modernization of the single-cylinder engine start by replacing the standard system by an electric starter is presented. Based on the calculated and experimental studies there have been provided the start-up characteristics of a single-cylinder engine. The measures to reduce the start-up time of the engine during the race in the Shell – EcoMarathon are offered.

  18. 21 CFR 26.11 - Start of operational period.

    Science.gov (United States)

    2010-04-01

    ... RECOGNITION OF PHARMACEUTICAL GOOD MANUFACTURING PRACTICE REPORTS, MEDICAL DEVICE QUALITY SYSTEM AUDIT REPORTS... Specific Sector Provisions for Pharmaceutical Good Manufacturing Practices § 26.11 Start of...

  19. School Starting Age and the Crime-Age Profile

    DEFF Research Database (Denmark)

    Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

    2015-01-01

    to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting age lowers the propensity to commit crime at young ages. We also find effects on the number of crimes......This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise...

  20. Sino-German research on rural development starts in Yunnan

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ A Sino-German project entitled Rural Development by Land Use Diversification: Stakeholder- based Strategies and Integrative Technologies for Agricultural Landscapes in Mountainous Southwest China started recently.

  1. Gasellitarinoita Aalto Start-Up Centeristä

    OpenAIRE

    Virtanen, Markku; Heimonen, Tomi; Hägg, Outi; Kiuru, Pertti; Rajahonka, Mervi

    2015-01-01

    Aalto Start-Up Center (ASUC) incubator activities started in Helsinki School of Economics in 1997. The University of Art and Design business incubator Arabus merged to this accelerator in 2009. When Aalto University started its operations in the year 2010, Aalto Start-Up Center became the established name of the incubator. At the end of 2013, altogether 460 companies had exited ASUC. In the 2010 - 2013 follow-up study it was found, that 5 % or nine of these alumni companies were the so-called...

  2. Survey on structural material investigations for SNR 300

    International Nuclear Information System (INIS)

    Type 304 SS in a modified, fully austenitic version has been used for the construction of the primary and secondary heat transfer system, including the vessel and the pumps; the steam generators were built of 2.25 Cr-1 Mo-Nb ferritic steel. Coordinated programs involving INTERATOM, KfK, ECN, TNO, CEN/Mol have been performed. The SNR-300 project related structural material activities have provided a broad base to describe materials properties behaviour and design limitations under aspects of long-term component reliability and availability. High temperature design needs have been covered by the development of constitutive relations and computational programs. Integrity considerations and deformation limits under hypothetical circumstances have been verified successfully. Investigations on alternative materials for permanent structure have been started

  3. Design Methodology of Camshaft Driven Charge Valves for Pneumatic Engine Starts

    Directory of Open Access Journals (Sweden)

    Moser Michael M.

    2015-01-01

    Full Text Available Idling losses constitute a significant amount of the fuel consumption of internal combustion engines. Therefore, shutting down the engine during idling phases can improve its overall efficiency. For driver acceptance a fast restart of the engine must be guaranteed. A fast engine start can be performed using a powerful electric starter and an appropriate battery which are found in hybrid electric vehicles, for example. However, these devices involve additional cost and weight. An alternative method is to use a tank with pressurized air that can be injected directly into the cylinders to start the engine pneumatically. In this paper, pneumatic engine starts using camshaft driven charge valves are discussed. A general methodology for an air-optimal charge valve design is presented which can deal with various requirements. The proposed design methodology is based on a process model representing pneumatic engine operation. A design example for a two-cylinder engine is shown, and the resulting optimized pneumatic start is experimentally verified on a test bench engine. The engine’s idling speed of 1200 rpm can be reached within 350 ms for an initial pressure in the air tank of 10 bar. A detailed system analysis highlights the characteristics of the optimal design found.

  4. Alternative fuels for vehicles; Alternative drivmidler

    Energy Technology Data Exchange (ETDEWEB)

    2012-02-15

    Up until 2020 and onwards the analysis indicates that especially electricity, biogas and natural gas as propellants is economically attractive compared to conventional gasoline and diesel while other fuels have the same or higher costs for petrol and diesel. Especially biogas and electricity will also offer significant reductions in CO{sub 2} emissions, but also hydrogen, methanol, DME and to a lesser extent the second generation bioethanol and most of the other alternative fuels reduce CO{sub 2} emissions. Use of the traditional food-based first generation biofuels involves, at best, only modest climate benefits if land use changes are counted, and at worst, significant negative climate effects. Natural gas as a propellant involves a moderate climate gain, but may play a role for building infrastructure and market for gaseous fuels in large fleets, thereby contributing to the phasing in of biogas for transport. The electric-based automotive fuels are the most effective due to a high efficiency of the engine and an increasing proportion of wind energy in the electricity supply. The methanol track also has a relatively high efficiency. Among the others, the track based on diesel engines (biodiesel) is more effective than the track based on gasoline/Otto engines (gas and ethanol) as a result of the diesel engine's better efficiency. For the heavy vehicles all the selected alternative fuels to varying degrees reduce emissions of CO{sub 2}, particularly DME based on wood. The only exception to this is - as for passenger cars - the propellant synthetic diesel based on coal. (LN).

  5. Biomechanical analysis of the swim-start: a review.

    Science.gov (United States)

    Vantorre, Julien; Chollet, Didier; Seifert, Ludovic

    2014-05-01

    This review updates the swim-start state of the art from a biomechanical standpoint. We review the contribution of the swim-start to overall swimming performance, the effects of various swim-start strategies, and skill effects across the range of swim-start strategies identified in the literature. The main objective is to determine the techniques to focus on in swimming training in the contemporary context of the sport. The phases leading to key temporal events of the swim-start, like water entry, require adaptations to the swimmer's chosen technique over the course of a performance; we thus define the swim-start as the moment when preparation for take-off begins to the moment when the swimming pattern begins. A secondary objective is to determine the role of adaptive variability as it emerges during the swim-start. Variability is contextualized as having a functional role and operating across multiple levels of analysis: inter-subject (expert versus non-expert), inter-trial or intra-subject (through repetitions of the same movement), and inter-preference (preferred versus non-preferred technique). Regarding skill effects, we assume that swim-start expertise is distinct from swim stroke expertise. Highly skilled swim-starts are distinguished in terms of several factors: reaction time from the start signal to the impulse on the block, including the control and regulation of foot force and foot orientation during take-off; appropriate amount of glide time before leg kicking commences; effective transition from leg kicking to break-out of full swimming with arm stroking; overall maximal leg and arm propulsion and minimal water resistance; and minimized energy expenditure through streamlined body position. Swimmers who are less expert at the swim-start spend more time in this phase and would benefit from training designed to reduce: (i) the time between reaction to the start signal and impulse on the block, and (ii) the time in transition (i.e., between gliding and leg

  6. Biomechanical analysis of the swim-start: a review.

    Science.gov (United States)

    Vantorre, Julien; Chollet, Didier; Seifert, Ludovic

    2014-05-01

    This review updates the swim-start state of the art from a biomechanical standpoint. We review the contribution of the swim-start to overall swimming performance, the effects of various swim-start strategies, and skill effects across the range of swim-start strategies identified in the literature. The main objective is to determine the techniques to focus on in swimming training in the contemporary context of the sport. The phases leading to key temporal events of the swim-start, like water entry, require adaptations to the swimmer's chosen technique over the course of a performance; we thus define the swim-start as the moment when preparation for take-off begins to the moment when the swimming pattern begins. A secondary objective is to determine the role of adaptive variability as it emerges during the swim-start. Variability is contextualized as having a functional role and operating across multiple levels of analysis: inter-subject (expert versus non-expert), inter-trial or intra-subject (through repetitions of the same movement), and inter-preference (preferred versus non-preferred technique). Regarding skill effects, we assume that swim-start expertise is distinct from swim stroke expertise. Highly skilled swim-starts are distinguished in terms of several factors: reaction time from the start signal to the impulse on the block, including the control and regulation of foot force and foot orientation during take-off; appropriate amount of glide time before leg kicking commences; effective transition from leg kicking to break-out of full swimming with arm stroking; overall maximal leg and arm propulsion and minimal water resistance; and minimized energy expenditure through streamlined body position. Swimmers who are less expert at the swim-start spend more time in this phase and would benefit from training designed to reduce: (i) the time between reaction to the start signal and impulse on the block, and (ii) the time in transition (i.e., between gliding and leg

  7. Alternative Energy Development and China's Energy Future

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Nina; Fridley, David

    2011-06-15

    In addition to promoting energy efficiency, China has actively pursued alternative energy development as a strategy to reduce its energy demand and carbon emissions. One area of particular focus has been to raise the share of alternative energy in China’s rapidly growing electricity generation with a 2020 target of 15% share of total primary energy. Over the last ten years, China has established several major renewable energy regulations along with programs and subsidies to encourage the growth of non-fossil alternative energy including solar, wind, nuclear, hydro, geothermal and biomass power as well as biofuels and coal alternatives. This study thus seeks to examine China’s alternative energy in terms of what has and will continue to drive alternative energy development in China as well as analyze in depth the growth potential and challenges facing each specific technology. This study found that despite recent policies enabling extraordinary capacity and investment growth, alternative energy technologies face constraints and barriers to growth. For relatively new technologies that have not achieved commercialization such as concentrated solar thermal, geothermal and biomass power, China faces technological limitations to expanding the scale of installed capacity. While some alternative technologies such as hydropower and coal alternatives have been slowed by uneven and often changing market and policy support, others such as wind and solar PV have encountered physical and institutional barriers to grid integration. Lastly, all alternative energy technologies face constraints in human resources and raw material resources including land and water, with some facing supply limitations in critical elements such as uranium for nuclear, neodymium for wind and rare earth metals for advanced solar PV. In light of China’s potential for and barriers to growth, the resource and energy requirement for alternative energy technologies were modeled and scenario analysis

  8. The Architecture of Chemical Alternatives Assessment.

    Science.gov (United States)

    Geiser, Kenneth; Tickner, Joel; Edwards, Sally; Rossi, Mark

    2015-12-01

    Chemical alternatives assessment is a method rapidly developing for use by businesses, governments, and nongovernment organizations seeking to substitute chemicals of concern in production processes and products. Chemical alternatives assessment is defined as a process for identifying, comparing, and selecting safer alternatives to chemicals of concern (including those in materials, processes, or technologies) on the basis of their hazards, performance, and economic viability. The process is intended to provide guidance for assuring that chemicals of concern are replaced with safer alternatives that are not likely to be later regretted. Conceptually, the assessment methods are developed from a set of three foundational pillars and five common principles. Based on a number of emerging alternatives assessment initiatives, in this commentary, we outline a chemical alternatives assessment blueprint structured around three broad steps: Scope, Assessment, and Selection and Implementation. Specific tasks and tools are identified for each of these three steps. While it is recognized that on-going practice will further refine and develop the method and tools, it is important that the structure of the assessment process remain flexible, adaptive, and focused on the substitution of chemicals of concern with safer alternatives. PMID:26630442

  9. Study of field assessment methods and worker risks for processing alternatives to support principles for FUSRAP waste materials. Part 1: Treatment methods and comparative risks of thorium removal from waste residues

    Energy Technology Data Exchange (ETDEWEB)

    Porter, R.D.; Hamby, D.M.; Martin, J.E.

    1997-07-01

    This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE`s Formerly Utilized Sites Remedial Action Program (FUSRAP). Its purpose was to provide information to the Environmental Management Advisory Board`s FUSRAP Committee for use in its deliberation of guiding principles for FUSRAP sites, in particular the degree to which treatment should be considered in the FUSRAP Committee`s recommendations. Treatment of FUSRAP wastes to remove thorium could be beneficial to management of lands that contain thorium if such treatment were effective and cost efficient. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation. Both types of information should be useful for decisions on whether and how to apply thorium removal methods to FUSRAP waste materials.

  10. Study of field assessment methods and worker risks for processing alternatives to support principles for FURSRAP waste materials. Part 1: Treatment methods and comparative risks of thorium removal from waste residues

    International Nuclear Information System (INIS)

    This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE's Formerly Utilized Sites Remedial Action Program (FUSRAP). Its purpose was to provide information to the Environmental Management Advisory Board's FUSRAP Committee for use in its deliberation of guiding principles for FUSRAP sites, in particular the degree to which treatment should be considered in the FUSRAP Committee's recommendations. Treatment of FUSRAP wastes to remove thorium could be beneficial to management of lands that contain thorium if such treatment were effective and cost efficient. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation. Both types of information should be useful for decisions on whether and how to apply thorium removal methods to FUSRAP waste materials

  11. Research reactors and alternative devices for research

    International Nuclear Information System (INIS)

    This report includes papers on research reactors and alternatives to the research reactors - radioisotopic neutron sources, cyclotrons, D-T neutron generators and small accelerators, used for radioisotope production, neutron activation analysis, material science, applied and basic research using neutron beams. A separate abstract was prepared for each of the 7 papers

  12. Alternatives to crop residues for soil amendment

    OpenAIRE

    Powell, J.M.; Unger, P.W.

    1997-01-01

    Metadata only record In semiarid agroecosystems, crop residues can provide important benefits of soil and water conservation, nutrient cycling, and improved subsequent crop yields. However, there are frequently multiple competing uses for residues, including animal forage, fuel, and construction material. This chapter discusses the various uses of crop residues and examines alternative soil amendments when crop residues cannot be left on the soil.

  13. Measurement of product of solid state laser materials by an alternative method: Application to Nd3+ doped YVO4 crystal for $^{4}F_{3/2}→ {}^{4}I_{11/2}$ transition

    Indian Academy of Sciences (India)

    P K Mukhopadhyay; Jogy George; S K Sharma; Rakesh Kapoor; T P S Nathan

    2001-01-01

    In this paper an alternative approach for measurement of product for $^{4}F_{3/2}→ {}^{4}I_{11/2}$ transition of Nd3+ doped YVO4 crystal is reported. In this method a microchip laser is formed by keeping a small piece of the sample in plane–plane resonator and a diode laser (808 nm) is used for pumping. The pump power induced thermal lensing effect is used to make the cavity stable. The cavity mode area is estimated by measuring the thermal lens focal length at the threshold and the average pump area is measured by Gaussian fit to the intensity profiles of the pump beam. The value of product of Nd:YVO4 crystal obtained by this method is within 10% of the reported values. The advantage of this method is that it is a simple method for direct measurement of product of laser crystals.

  14. Graphite powder as an alternative or supplement to reversed-phase material for desalting and concentration of peptide mixtures prior to matrix-assisted laser desorption/ionization-mass spectrometry

    DEFF Research Database (Denmark)

    Larsen, Martin Røssel; Cordwell, Stuart J; Roepstorff, Peter

    2002-01-01

    The success attributed to identification and characterization of gel separated proteins by mass spectrometry (MS) is highly dependent on the percentage of an entire sequence covered by matching peptides derived from enzymatic digestion. Desalting and concentration of peptide mixtures on reversed......-phase (RP) microcolumns prior to mass spectrometric analysis have resulted in increased signal-to-noise ratio and sensitivity, and consequently higher sequence coverage. A large proportion of peptides, however, remains undetected by MS presumably because they are lost during sample preparation...... on microcolumns, or are suppressed in the ionization process. We report here the use of graphite powder packed in constricted GELoader tips as an alternative to RP microcolumns for desalting and concentration of peptide mixtures prior to MS. Such columns are able to retain small and/or hydrophilic peptides...

  15. Start-Up Costs in American Research Universities.

    Science.gov (United States)

    Ehrenberg, Ronald G.; Rizzo, Michael J.; Condie, Scott S.

    This report briefly summarizes findings from the 2002 Cornell Higher Education Research Institute survey of start-up costs at the over 220 universities classified as research and doctoral universities by the Carnegie Foundation in 1994. It reports the mean start-up cost packages across institutions for new assistant professors and senior faculty,…

  16. 30 CFR 56.14201 - Conveyor start-up warnings.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor start-up warnings. 56.14201 Section 56.14201 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Equipment Safety Practices and Operational Procedures § 56.14201 Conveyor start-up warnings. (a) When...

  17. 30 CFR 57.14201 - Conveyor start-up warnings.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveyor start-up warnings. 57.14201 Section 57.14201 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Equipment Safety Practices and Operational Procedures § 57.14201 Conveyor start-up warnings. (a) When...

  18. Start-up Costs, Taxes and Innovative Entrepreneurship

    NARCIS (Netherlands)

    P. Darnihamedani (Pourya); J.H. Block (Jörn); S.J.A. Hessels (Jolanda); A. Simonyan (Aram)

    2015-01-01

    markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off cost

  19. How Does Personal Bankruptcy Law Affect Start-ups?

    NARCIS (Netherlands)

    Cerqueiro, G.M.; Penas, M.F.

    2011-01-01

    We analyze the effect of changes in U.S. state personal exemptions on the financing structure and performance of a representative sample of start-ups. An increase in the amount of borrower’s personal wealth protected in bankruptcy reduces the availability of bank credit to all start-ups. Owners of u

  20. Summary of Head Start Provisions on Homelessness and Foster Care

    Science.gov (United States)

    National Association for the Education of Homeless Children and Youth, 2008

    2008-01-01

    On Wednesday, December 12, President Bush signed the "Improving Head Start for School Readiness Act of 2007" into law. The legislation reauthorizes the Head Start Act and contains numerous provisions on homelessness and foster care. A summary of those provisions is provided in this paper.