WorldWideScience

Sample records for alkaline earth metal

  1. Alkaline earth metal thioindates

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov-Ehmin, B.N.; Ivlieva, V.I.; Filatenko, L.A.; Zajtsev, B.E.; Kaziev, G.Z.; Sarabiya, M.G.

    1984-08-01

    Alkaline earth metal thioindates of MIn/sub 2/S/sub 4/ composition were synthesized by interaction of alkaline earth metal oxoindates with hydrogen sulfide during heating. Investigation into the compounds by X-ray analysis showed that calcium compound crystallizes in cubic crystal system and strontium and barium compounds in rhombic crystal system. Lattice parameters and the number of formula units were determined. Thioindates of M/sub 3/In/sub 2/S/sub 6/ composition were synthesized, their individuality was shown.

  2. Solvent Extraction of Alkaline Earth Metals with Alkylphosphorus Acids

    Institute of Scientific and Technical Information of China (English)

    XUXin; ZHUTun

    2002-01-01

    Solvent extraction equiliria of four main alkaline earth metals (magnesium, calcium, strontium and barium) with di(2-ethylhexyl) phosphoric acid (DEHPA), 2-ethylhexyl phosphonic acid mono-(2-ethylhexyl) ester, di(2,4,4-tri-methylpentyl) phosphinic acid and IR spectra of the extracts have been studied. The selectivity order is dependent of the e/r value and hydration energy of the metal ions. The minor shift of the P→O in IR absorption of the alkaline earth metal extracts indicates that the interaction between the metal ions and P→O is much weaker for alkaline earth metals than for transitional metals. The distribution of the four alkaline earth elements between aqueous solutions and solutions of DEHPA and neutral organophosphorus compunds, tri-n-butyl phosphate (TBP) or tri-octyl phosphine oxide (TOPO) in kerosene have been determined at varying ratio of TBP or TOPO to DEHPA and the positive synergism is observed. The synergic effects is explained by using IR spectra of the loaded organic phase.

  3. Controlled charge exchange between alkaline earth metals and their ions

    Science.gov (United States)

    Gacesa, Marko; Côté, Robin

    2015-05-01

    We theoretically investigate the prospects of realizing controlled charge exchange via magnetic Feshbach resonances in cold and ultracold collisions of atoms and ions. In particular, we focus on near-resonant charge exchange in heteroisotopic combinations of alkaline earth metals, such as 9Be++10 Be9 Be+10Be+ , which exhibit favorable electronic and hyperfine structure. The quantum scattering calculations are performed for a range of initial states and experimentally attainable magnetic fields in standard coupled-channel Feshbach projection formalism, where higher-order corrections such as the mass-polarization term are explicitely included. In addition, we predict a number of magnetic Feshbach resonances for different heteronuclear isotopic combinations of the listed and related alkaline earth elements. Our results imply that near-resonant charge-exchange could be used to realize atom-ion quantum gates, as well as controlled charge transfer in optically trapped cold quantum gases. This work is partially supported by ARO.

  4. Structural variations in layered alkaline earth metal cyclohexyl phosphonates

    Indian Academy of Sciences (India)

    Ramaswamy Murugavel; Nayanmoni Gogoi

    2009-06-01

    Two series of alkaline earth metal cyclohexyl phosphonates, M(C6H11PO3H)2(H2O) (M = Ca, Sr and Ba) (1–3) and M(C6H11PO3)(H2O) (M = Mg, Ca, Sr, and Ba) (4–7) have been synthesized under mild reaction conditions. All new compounds have been characterized using elemental analysis, IR, TGA and powder X-ray diffraction techniques. The molecular structure of compound 2 determined using single crystal X-ray diffraction technique reveals a layered polymeric structure.

  5. Quantum computing with alkaline-Earth-metal atoms.

    Science.gov (United States)

    Daley, Andrew J; Boyd, Martin M; Ye, Jun; Zoller, Peter

    2008-10-24

    We present a complete scheme for quantum information processing using the unique features of alkaline-earth-metal atoms. We show how two completely independent lattices can be formed for the 1S0 and 3P0 states, with one used as a storage lattice for qubits encoded on the nuclear spin, and the other as a transport lattice to move qubits and perform gate operations. We discuss how the 3P2 level can be used for addressing of individual qubits, and how collisional losses from metastable states can be used to perform gates via a lossy blockade mechanism.

  6. THE TRANSFER OF ALKALINE EARTH-METAL ION AT W/NB INTERFACE FACILITATED BY JOSAMYCIN

    Institute of Scientific and Technical Information of China (English)

    范瑞溪; 狄俊伟

    1991-01-01

    This paper describes the invesligation of the transfer behaviour of the alkaline earth-metal cations across the water/nitrobenzene interface facilitated by josamycin in the nitrobenzene phase using semi-differential cyclic voltammetry .The peak height is directly proportional to the concentration of josaycin (nb) and to the potential scan rate.The complexes formed from alkaline earth-metal ions and josamycin at the w/nb interface are ML22+ ion.

  7. Doping of graphite by an alkaline-earth metal to reduce the work function

    NARCIS (Netherlands)

    Baturin, AS; Nikolski, KN; Knyazev, AI; Tchesov, RG; Sheshin, EP

    2004-01-01

    A technique for reducing the work function of a field-emission graphite cathode by doping it by an alkaline-earth metal (barium) is suggested. A model of formation of a barium monolayer on the cathode surface is proposed. Field-emission tests show that the operating voltage of the doped cathode is l

  8. Calculated Structural Phase-Transitions in the Alkaline-Earth Metals

    DEFF Research Database (Denmark)

    Skriver, Hans Lomholt

    1982-01-01

    The local-density approximation and the linear muffin-tin orbital method have been used within the atomic-sphere approximation to calculate structural energy differences for all the alkaline earth metals at zero temperature. At ordinary pressure the calculations predict the crystal structure...

  9. Solvation structures and dynamics of alkaline earth metal halides in supercritical water: A molecular dynamics study

    Science.gov (United States)

    Keshri, Sonanki; Mandal, Ratnamala; Tembe, B. L.

    2016-09-01

    Constrained molecular dynamics simulations of alkaline earth metal halides have been carried out to investigate their structural and dynamical properties in supercritical water. Potentials of mean force (PMFs) for all the alkaline earth metal halides in supercritical water have been computed. Contact ion pairs (CIPs) are found to be more stable than all other configurations of the ion pairs except for MgI2 where solvent shared ion pair (SShIP) is more stable than the CIP. There is hardly any difference in the PMFs between the M2+ (M = Mg, Ca, Sr, Ba) and the X- (X = F, Cl, Br, I) ions whether the second X- ion is present in the first coordination shell of the M2+ ion or not. The solvent molecules in the solvation shells diffuse at a much slower rate compared to the bulk. Orientational distribution functions of solvent molecules are sharper for smaller ions.

  10. Molecular dynamics of liquid alkaline-earth metals near the melting point

    Indian Academy of Sciences (India)

    J K Baria; A R Jani

    2010-10-01

    Results of the studies of the properties like binding energy, the pair distribution function (), the structure factor (), specific heat at constant volume, velocity autocorrelation function (VACF), radial distribution function, self-diffusion coefficient and coordination number of alkaline-earth metals (Be, Mg, Ca, Sr and Ba) near melting point using molecular dynamics (MD) simulation technique using a pseudopotential proposed by us are presented in this article. Good agreement with the experiment is achieved for the binding energy, pair distribution function and structure factor, and these results compare favourably with the results obtained by other such calculations, showing the transferability of the pseudopotential used from solid to liquid environment in the case of alkaline-earth metals.

  11. Alkaline earth metal doped tin oxide as a novel oxygen storage material

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Qiang, E-mail: dong@tagen.tohoku.ac.jp [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku Sendai 980-8577 (Japan); Yin, Shu; Yoshida, Mizuki; Wu, Xiaoyong; Liu, Bin [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku Sendai 980-8577 (Japan); Miura, Akira; Takei, Takahiro; Kumada, Nobuhiro [Department of Research Interdisciplinary Graduate School of Medicine and Engineering, University of Yamanashi, Miyamae cho-7, Kofu 400-8511 (Japan); Sato, Tsugio [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku Sendai 980-8577 (Japan)

    2015-09-15

    Alkaline earth metal doped tin oxide (SnO{sub 2}) hollow nanospheres with a diameter of 50 nm have been synthesized successfully via a facial solvothermal route in a very simple system composed of only ethanol, acetic acid, SnCl{sub 4}·5H{sub 2}O and A(NO{sub 3}){sub 2}·xH{sub 2}O (A = Mg, Ca, Sr, Ba). The synthesized undoped SnO{sub 2} and A-doped SnO{sub 2} hollow nanospheres were characterized by the oxygen storage capacity (OSC), X-ray diffraction, transmission electron microscopy and the Brunauer–Emmet–Teller (BET) technique. The OSC values of all samples were measured using thermogravimetric-differential thermal analysis. The incorporation of alkaline earth metal ion into tin oxide greatly enhanced the thermal stability and OSC. Especially, Ba-doped SnO{sub 2} hollow nanospheres calcined at 1000 °C for 20 h with a BET surface area of 61 m{sup 2} g{sup −1} exhibited the considerably high OSC of 457 μmol-O g{sup −1} and good thermal stability. Alkaline earth metal doped tin oxide has the potential to be a novel oxygen storage material.

  12. Effects of alkaline earth metal ion complexation on amino acid zwitterion stability: Results from infrared action spectroscopy

    NARCIS (Netherlands)

    Bush, M. F.; Oomens, J.; Saykally, R. J.; Williams, E. R.

    2008-01-01

    The structures of isolated alkaline earth metal cationized amino acids are investigated using infrared multiple photon dissociation (IRMPD) spectroscopy and theory. These results indicate that arginine, glutamine, proline, serine, and valine all adopt zwitterionic structures when complexed with diva

  13. Adsorption of alkali, alkaline-earth, and 3d transition metal atoms on silicene

    Science.gov (United States)

    Sahin, H.; Peeters, F. M.

    2013-02-01

    The adsorption characteristics of alkali, alkaline-earth, and transition metal adatoms on silicene, a graphene-like monolayer structure of silicon are analyzed by means of first-principles calculations. In contrast to graphene, interaction between the metal atoms and the silicene surface is quite strong due to its highly reactive buckled hexagonal structure. In addition to structural properties, we also calculate the electronic band dispersion, net magnetic moment, charge transfer, work function, and dipole moment of the metal adsorbed silicene sheets. Alkali metals, Li, Na, and K, adsorb to hollow sites without any lattice distortion. As a consequence of the significant charge transfer from alkalis to silicene, metalization of silicene takes place. Trends directly related to atomic size, adsorption height, work function, and dipole moment of the silicene/alkali adatom system are also revealed. We found that the adsorption of alkaline-earth metals on silicene is entirely different from their adsorption on graphene. The adsorption of Be, Mg, and Ca turns silicene into a narrow gap semiconductor. Adsorption characteristics of eight transition metals Ti, V, Cr, Mn, Fe, Co, Mo, and W are also investigated. As a result of their partially occupied d orbital, transition metals show diverse structural, electronic, and magnetic properties. Upon the adsorption of transition metals, depending on the adatom type and atomic radius, the system can exhibit metal, half-metal, and semiconducting behavior. For all metal adsorbates, the direction of the charge transfer is from adsorbate to silicene, because of its high surface reactivity. Our results indicate that the reactive crystal structure of silicene provides a rich playground for functionalization at nanoscale.

  14. Nano porous alkaline earth metal silicates as free fatty acid adsorbents from Crude Palm Oil (CPO)

    Science.gov (United States)

    Masmur, Indra; Sembiring, Seri Bima; Bangun, Nimpan; Kaban, Jamaran; Putri, Nabila Karina

    2017-01-01

    Free fatty acids(FFA) from Crude Palm Oil (CPO) have been adsorbed by alkaline earth metal silicate (M-silicate : M = Mg, Ca, Sr and Ba) adsorbents in ethanol using batch method. The adsorbents were prepared from the chloride salts of alkaline metals and Na2SiO3. The resulting white solid of the alkaline earth metal silicates were then heated at 800°C for 3 hours to enlarge their porosities. All adsorbents were characterized by SEM-EDX, XRD and BET. The EDX spectrum of SEM-EDX showed the appearance of all elements in the adsorbents, and the XRD spectrum of all adsorbents showed that they have crystobalite structure. The porosity of the adsorbents calculated by BET method showed that the porosities of the adsorbents range from 2.0884 - 2.0969 nm. All the adsorbents were used to adsorb the FFA from CPO containing 4.79%, 7.3%, 10.37% and 13.34% of FFA. The ratio of adsorbent to CPO to be used in adsorption of FFA from CPO were made 1:1, 1:2 and 1:3, with adsorption time of 1 hour. We found that the maximum adsorption of FFA from CPO was given by Ca-Silicate adsorbent which was between 69.86 - 94.78%, while the lowest adsorption was shown by Mg-silicate adsorbent which was 49.32 -74.53%.

  15. Bond-length distributions for ions bonded to oxygen: alkali and alkaline-earth metals.

    Science.gov (United States)

    Gagné, Olivier Charles; Hawthorne, Frank Christopher

    2016-08-01

    Bond-length distributions have been examined for 55 configurations of alkali-metal ions and 29 configurations of alkaline-earth-metal ions bonded to oxygen, for 4859 coordination polyhedra and 38 594 bond distances (alkali metals), and for 3038 coordination polyhedra and 24 487 bond distances (alkaline-earth metals). Bond lengths generally show a positively skewed Gaussian distribution that originates from the variation in Born repulsion and Coulomb attraction as a function of interatomic distance. The skewness and kurtosis of these distributions generally decrease with increasing coordination number of the central cation, a result of decreasing Born repulsion with increasing coordination number. We confirm the following minimum coordination numbers: ([3])Li(+), ([3])Na(+), ([4])K(+), ([4])Rb(+), ([6])Cs(+), ([3])Be(2+), ([4])Mg(2+), ([6])Ca(2+), ([6])Sr(2+) and ([6])Ba(2+), but note that some reported examples are the result of extensive dynamic and/or positional short-range disorder and are not ordered arrangements. Some distributions of bond lengths are distinctly multi-modal. This is commonly due to the occurrence of large numbers of structure refinements of a particular structure type in which a particular cation is always present, leading to an over-representation of a specific range of bond lengths. Outliers in the distributions of mean bond lengths are often associated with anomalous values of atomic displacement of the constituent cations and/or anions. For a sample of ([6])Na(+), the ratio Ueq(Na)/Ueq(bonded anions) is partially correlated with 〈([6])Na(+)-O(2-)〉 (R(2) = 0.57), suggesting that the mean bond length is correlated with vibrational/displacement characteristics of the constituent ions for a fixed coordination number. Mean bond lengths also show a weak correlation with bond-length distortion from the mean value in general, although some coordination numbers show the widest variation in mean bond length for zero distortion, e.g. Li(+) in

  16. Long-range interacting many-body systems with alkaline-earth-metal atoms.

    Science.gov (United States)

    Olmos, B; Yu, D; Singh, Y; Schreck, F; Bongs, K; Lesanovsky, I

    2013-04-01

    Alkaline-earth-metal atoms can exhibit long-range dipolar interactions, which are generated via the coherent exchange of photons on the (3)P(0) - (3)D(1) transition of the triplet manifold. In the case of bosonic strontium, which we discuss here, this transition has a wavelength of 2.6 μm and a dipole moment of 4.03 D, and there exists a magic wavelength permitting the creation of optical lattices that are identical for the states (3)P(0) and (3)D(1). This interaction enables the realization and study of mixtures of hard-core lattice bosons featuring long-range hopping, with tunable disorder and anisotropy. We derive the many-body master equation, investigate the dynamics of excitation transport, and analyze spectroscopic signatures stemming from coherent long-range interactions and collective dissipation. Our results show that lattice gases of alkaline-earth-metal atoms permit the creation of long-lived collective atomic states and constitute a simple and versatile platform for the exploration of many-body systems with long-range interactions. As such, they represent an alternative to current related efforts employing Rydberg gases, atoms with large magnetic moment, or polar molecules.

  17. Long-range interacting many-body systems with alkaline-earth-metal atoms

    CERN Document Server

    Olmos, B; Singh, Y; Schreck, F; Bongs, K; Lesanovsky, I

    2012-01-01

    Alkaline-earth-metal atoms exhibit long-range dipolar interactions, which are generated via the coherent exchange of photons on the 3P_0-3D_1-transition of the triplet manifold. In case of bosonic strontium, which we discuss here, this transition has a wavelength of 2.7 \\mu m and a dipole moment of 2.46 Debye, and there exists a magic wavelength permitting the creation of optical lattices that are identical for the states 3P_0 and 3D_1. This interaction enables the realization and study of mixtures of hard-core lattice bosons featuring long-range hopping, with tuneable disorder and anisotropy. We derive the many-body Master equation, investigate the dynamics of excitation transport and analyze spectroscopic signatures stemming from coherent long-range interactions and collective dissipation. Our results show that lattice gases of alkaline-earth-metal atoms permit the creation of long-lived collective atomic states and constitute a simple and versatile platform for the exploration of many-body systems with lon...

  18. Ab Initio Calculation of 19F NMR Chemical Shielding for Alkaline-earth-metal Fluorides

    Institute of Scientific and Technical Information of China (English)

    CAI,Shu-Hui(蔡淑惠); CHEN,Zhong,(陈忠); LU,Xin(吕鑫); CHEN,Zhi-Wei(陈志伟); WAN,Hui-Lin(万惠霖)

    2001-01-01

    Gauge-independent atomic orbital (GIAO) method atHartree-Fock (HF) and density functional theory (DFr) lev-els,respectively,was employed to calculate 19F NMR chemi-cal shieldings of solid state alkaline-earth-metal fluorides MF2 (M = Mg,Ca,Sr,Ba).The results show that,although thecalculated19F chemical shieldings tend to be larger than the experinental values,they have a fairly good linear relation-ship with the observed ones.The calculated results based on different combinations of basis sets show that the B3LYP (ahybrid of DFT with HF) predictions are greatly superior tothe I-IF predictions.When a basis set of metal atom with ef- fecfive core potential (ECP) has well representation of valencewavefunction,especially wavefuncfion of d component,andproper definition of core electron nmnher,it can be applied toobtain 19F chemical shielding which is dose to that of all-elec-tron calculation.Tne variation of 19F chemical shielding of al-kaline-earth-metal fluorides correlates well with the latticefactor A/R2.``

  19. Electric dipole polarizability of alkaline-Earth-metal atoms from perturbed relativistic coupled-cluster theory with triples

    CERN Document Server

    Chattopadhyay, S; Angom, D

    2014-01-01

    The perturbed relativistic coupled-cluster (PRCC) theory is applied to calculate the electric dipole polarizabilities of alkaline Earth metal atoms. The Dirac-Coulomb-Breit atomic Hamiltonian is used and we include the triple excitations in the relativistic coupled-cluster (RCC) theory. The theoretical issues related to the triple excitation cluster operators are described in detail and we also provide details on the computational implementation. The PRCC theory results are in good agreement with the experimental and previous theoretical results. We, then, highlight the importance of considering the Breit interaction for alkaline Earth metal atoms.

  20. Linear alkaline earth metal phosphinate coordination polymers: synthesis and structural characterization.

    Science.gov (United States)

    Rood, Jeffrey A; Huttenstine, Ashley L; Schmidt, Zachery A; White, Michael R; Oliver, Allen G

    2014-06-01

    Reaction of alkaline earth metal salts with diphenylphosphinic acid in dimethylformamide solvent afforded four coordination polymers: [Mg3(O2PPh2)6(DMF)2]·2DMF (I), [Ca(O2PPh2)2(DMF)2] (II), [Sr(O2PPh2)2(DMF)2] (III) and [Ba(O2PPh2)2(DMF)2] (IV) (where DMF is N,N-dimethylformamide). Single-crystal X-ray diffraction revealed that all four compounds produce linear chain structures in the solid state, with the Ca, Sr and Ba forming isostructural crystals. The bulk materials were characterized by FT-IR and (1)H NMR spectroscopy and elemental analyses.

  1. Alkaline-earth metal hydrides as novel host lattices for Eu(II) luminescence.

    Science.gov (United States)

    Kunkel, Nathalie; Kohlmann, Holger; Sayede, Adlane; Springborg, Michael

    2011-07-04

    Luminescence of divalent europium has been investigated for the first time in metal hydrides. A complete solid-solution series was found for the pseudobinary system Eu(x)Sr(1-x)H(2) [a = 637.6(1) pm -12.1(3)x pm, b = 387.0(1)-6.5(2)x pm, c = 732.2(2)-10.1(4)x pm]. Europium-doped alkaline-earth hydrides Eu(x)M(1-x)H(2) (M = Ca, Sr, Ba) with a small europium concentration (x = 0.005) exhibit luminescence with maximum emission wavelengths of 764 nm (M = Ca), 728 nm (M = Sr), and 750 nm (M = Ba); i.e., the emission energy of divalent europium shows an extremely large red shift compared to the emission energies of fluorides or oxides. Theoretical calculations (LDA+U) confirm decreasing band gaps with increasing europium content of the solid solutions.

  2. The contents of alkali and alkaline earth metals in soils of the southern Cis-Ural region

    Science.gov (United States)

    Asylbaev, I. G.; Khabirov, I. K.

    2016-01-01

    The contents and distribution patterns of alkali and alkaline earth metals in soils and rocks of the southern Cis-Ural region were studied. A database on the contents of these metals was developed, the soils were classified with respect to their provision with these metals, and corresponding schematic maps showing their distribution in soils of the region were compiled. It was found that the contents of these metals decrease from east to west (from the Yuryuzan-Aisk Piedmont Plain to the Ufa Plateau and to the Belebeevsk Upland), and their distribution patterns change. Among alkali metals, the highest accumulation in the soils is typical of potassium, sodium, and cesium; among alkaline earth metals, of strontium and barium.

  3. Selective oxidation of methanol to hydrogen over gold catalysts promoted by alkaline-earth-metal and lanthanum oxides

    NARCIS (Netherlands)

    Hereijgers, B.P.C.; Weckhuysen, B.M.

    2009-01-01

    A series of alumina-supported gold catalysts was investigated for the CO-free production of hydrogen by partial oxidation of methanol. The addition of alkaline-earth metal oxide promoters resulted in a significant improvement of the catalytic performance. The methanol conversion was ca. 85 % with al

  4. Syntheses, structure and properties of Alkaline-earth metal salts of 4-Nitrophenylacetic acid

    Indian Academy of Sciences (India)

    BIKSHANDARKOIL R SRINIVASAN; KIRAN T DHAVSKAR; CHRISTIAN NÄTHER

    2016-11-01

    The synthesis, crystal structure, spectral characteristics and thermal properties of alkaline-earth metal salts of 4-nitrophenylacetic acid (4-npaH) namely, [Mg(H₂O)₆](4-npa)₂·4H₂O (4-npa = 4-nitrophenylacetate) (1), [Ca(H₂O)₂(4-npa)₂] (2) and [Sr(H₂O)₃(4-npa)₂]·4.5H₂O(3) are reported. In 1, the 4-npa ion functions as a charge balancing counter anion for the octahedral [Mg(H₂O)6]²⁺ unit with the Mg(II) ion situated on a centre of inversion. The two unique lattice water molecules link the [Mg(H₂O)₆]²⁺ cations and 4-npa anions with the aid of O-H· · ·O interactions. Compounds 2 and 3 are one-dimensional (1-D) coordination polymers containing an eight coordinated Ca(II) situated in a general position and a nine coordinated Sr(II) located on a twofold axis. The μ₂-bridging tridentate binding modes of the crystallographically independent 4-npa ligands in 2 and the unique 4-npa ligand in 3 link the bivalent metal ions into an infinite chain with alternating Ca· · · Ca separations of 3.989 and 4.009 Å, respectively, and a single Sr· · · Sr separation of 4.194Å in the 1-D chain.

  5. Influence of alkaline earth metals on molecular structure of 3-nitrobenzoic acid in comparison with alkali metals effect.

    Science.gov (United States)

    Samsonowicz, M; Regulska, E; Lewandowski, W

    2011-11-01

    The influence of beryllium, magnesium, calcium, strontium and barium cations on the electronic system of 3-nitrobenzoic acid was studied in comparison with studied earlier alkali metal ions. The vibrational FT-IR (in KBr and ATR techniques) and (1)H and (13)C NMR spectra were recorded for 3-nitrobenzoic acid and its salts. Characteristic shifts in IR and NMR spectra along 3-nitrobenzoates of divalent metal series Mg→Ba were compared with series of univalent metal Li→Cs salts. Good correlations between the wavenumbers of the vibrational bands in the IR spectra for 3-nitrobenzoates and ionic potential, electronegativity, inverse of atomic mass, atomic radius and ionization energy of metals were found for alkaline earth metals as well as for alkali metals. The density functional (DFT) hybrid method B3LYP with two basis sets: 6-311++G** and LANL2DZ were used to calculate optimized geometrical structures of studied compounds. The theoretical wavenumbers and intensities of IR spectra as well as chemical shifts in NMR spectra were obtained. Geometric aromaticity indices, atomic charges, dipole moments and energies were also calculated. The calculated parameters were compared to experimental characteristic of studied compounds.

  6. Characterization of alkali-metal and alkaline-earth nitrates by vibrational spectroscopy

    Directory of Open Access Journals (Sweden)

    Martínez, S.

    1992-09-01

    Full Text Available Infrared spectra of sodium and potassium alkaline-metal nitrates and magnesium and calcium alkali-earth nitrates in solid phase had been recorded in order to assign the fundamental bands. The influence of the dispersal médium (alkaline halide, employed in the solid sample preparation have been discussed. The quantitative measurements of the band in ten sities at 1387 cm-1 (present in the I.R. spectra of the four nitrates in KBr médium allowed us to determine the Lambert-Beer law slopes for each compound. These values are differents (bearing in mind experimental random errors, so we have could to affirm the nonexistence of solid solution between the nitrate and the alkaline halide médium. The L-B law obtained by us can be used for the Identification differentiation and quantitative analysis of these nitrates in solid phase, even if they are present in a very low concentration.

    Se ha realizado la asignación de los espectros infrarrojo (IR de los nitratos alcalinos, sódico y potásico, y de los alcalinotérreos, magnésico y cálcico, en estado sólido. Se ha visto la influencia del medio dispersante (haluro alcalino, utilizado en la preparación de la muestra sólida. El estudio cuantitativo de la absorbencia de la banda a 1.387 cm-1 (presente en los espectros IR de los cuatro nitratos en medio KBr permite determinar las pendientes de la Ley de Lambert-Beer Se comprueba que dichas pendientes son diferentes lo que conduce a poder afirmar que no se produce disolución sólida entre el KBr y el nitrato alcalino o alcalinotérreo. La determinación de la ley de Lambert-Beer permite la identificación y el análisis cualitativo y cuantitativo por espectroscopia IR de estos nitratos cuando están presentes en bajas concentraciones en muestras sólidas.

  7. Recent advances in tailoring the aggregation of heavier alkaline earth metal halides, alkoxides and aryloxides from non-aqueous solvents.

    Science.gov (United States)

    Fromm, Katharina M

    2006-11-21

    This overview on one of the subjects treated in our group deals with the synthesis and study of low-dimensional polymer and molecular solid state structures formed with alkaline earth metal ions in non-aqueous solvents. We have chosen several synthetic approaches in order to obtain such compounds. The first concept deals with the "cutting out" of structural fragments from a solid state structure of a binary compound, which will be explained with reference to BaI2. Depending on the size and concentration of oxygen donor ligands, used as chemical scissors on BaI2, three-, two-, one- and zero-dimensional derived adducts of BaI2 are obtained, comparable to a structural genealogy tree for BaI2. A second part deals with the supramolecular approach for the synthesis of low dimensional polymeric compounds based on alkaline earth metal iodides, obtained by the combination of metal ion coordination with hydrogen bonding between the cationic complexes and their anions. Certain circumstances allow rules to be established for the prediction of the dimensionality of a given compound, contributing to the fundamental problem of structure prediction in crystal engineering. A third section describes a synthetic approach for generating pure alkaline earth metal cage compounds as well as alkali and alkaline earth mixed metal clusters. A first step deals with different molecular solvated alkaline earth metal iodides which are investigated as a function of the ligand size in non-aqueous solvents. These are then reacted with some alkali metal compound in order to partially or totally eliminate alkali iodide and to form the targeted clusters. These unique structures of ligand stabilized metal halide, hydroxide and/or alkoxide and aryloxide aggregates are of interest as potential precursors for oxide materials and as catalysts. Approaches to two synthetic methods of the latter, sol-gel and (MO)CVD (metal-organic chemical vapour deposition), are investigated with some of our compounds. (D

  8. Red-emitting alkaline-earth rare-earth pentaoxometallates powders prepared by metal carboxylates solution

    Indian Academy of Sciences (India)

    Kyu-Seog Hwang; Sung-Dae Kim; Seung Hwangbo; Jin-Tae Kim

    2013-06-01

    Moisture-insensitive metal carboxylates that are mostly liquids at room temperature have been first applied to the preparation of strontium europium aluminate (Sr2EuAlO5) powders for red-emitting phosphor under near ultraviolet radiation. Strontium naphthenate, aluminium-2-ethylhexanoate and europium-2-ethylhexanoate were dissolved with toluene to prepare starting solution. Precursor pyrolyzed at 500 °C for 240 min was finally annealed at 900–1200 °C for 240 min in Ar. X-ray diffraction analysis, field emission–scanning electron microscope and fluorescent spectrophotometer were used to evaluate structural and optical properties. For the 1000 °C-annealed powders with regular shape and narrow size distribution confirmed by FE–SEM observation, strong red emission at 615nm under the excitation of 395nm maximum was reached, then the higher annealed samples at above 1100 °C gave the lower emission intensities.

  9. The Effect of Ormosil Matrix Composition and Alkaline Earth Metal Doping on the Photochromic Response of Ormosil-Phosphotungstate Films

    OpenAIRE

    Ferreira Neto,Elias P.; Simões,Mateus B.; Noveletto,Julia C.; Yabarrena,Jean M. S. C.; Ullah,Sajjad; Ubirajara P. Rodrigues Filho

    2015-01-01

    In this study, polyoxometallate based hybrid photochromic materials were prepared by incorporating phosphotungstate anion, PW12O403−, (PW) in hybrid tetraethyl orthosilicate and (3-glycidyloxypropyl)trimethoxysilane TEOS-GPTMS derived organomodified silicates (Ormosil) matrices by sol-gel method and the resulting materials were used to prepare multilayer films by dip-coating method. The effect of alkaline earth metal cations doping and matrix composition (%GPTMS) on the photochromic res...

  10. Spin-Orbit-Coupled Correlated Metal Phase in Kondo Lattices: An Implementation with Alkaline-Earth Atoms

    Science.gov (United States)

    Isaev, L.; Schachenmayer, J.; Rey, A. M.

    2016-09-01

    We show that an interplay between quantum effects, strong on-site ferromagnetic exchange interaction, and antiferromagnetic correlations in Kondo lattices can give rise to an exotic spin-orbit coupled metallic state in regimes where classical treatments predict a trivial insulating behavior. This phenomenon can be simulated with ultracold alkaline-earth fermionic atoms subject to a laser-induced magnetic field by observing dynamics of spin-charge excitations in quench experiments.

  11. Spin-Orbit-Coupled Correlated Metal Phase in Kondo Lattices: An Implementation with Alkaline-Earth Atoms.

    Science.gov (United States)

    Isaev, L; Schachenmayer, J; Rey, A M

    2016-09-23

    We show that an interplay between quantum effects, strong on-site ferromagnetic exchange interaction, and antiferromagnetic correlations in Kondo lattices can give rise to an exotic spin-orbit coupled metallic state in regimes where classical treatments predict a trivial insulating behavior. This phenomenon can be simulated with ultracold alkaline-earth fermionic atoms subject to a laser-induced magnetic field by observing dynamics of spin-charge excitations in quench experiments.

  12. Binding and selectivity of phenazino-18-crown-6-ether with alkali, alkaline earth and toxic metal species: A DFT study

    Science.gov (United States)

    Islam, Nasarul; Chimni, Swapandeep Singh

    2017-02-01

    The interactions of phenazino-crown ether ligands with alkali, alkaline earth and selected toxic species were investigated using density functional theory modelling by employing B3PW91/6-311G ++ (d, p) level of theory. The complex stability was analysed in terms of binding energies, perturbation energies, position of highest molecular orbital and energy gap values. In general, the complexes formed by P18C6-1a ligand with metal cations were found to be more stable than those with P18C6-1b. Among alkali and alkaline earth metals complexes having highest stability was observed for the complex formed by P18C6-1a with Be2+. Computational calculations of P18C6 ligand with toxic metal ions reveals that the P18C6-Cr6+ metal complexes acquire envelop like geometry, leading to higher binding energy values. Comparing the binding energies of neutral and monocations of Ag and Hg, the former had higher value both in neutral as well as monocation state. Thus, the stability of metal complexes is determined not only by the ligand but also by the type of metal ion. In solvent systems the stability constants of metal complexes were found increasing with decreasing permittivity of the solvent. This reflects the inherited polar character of the protic solvents stabilises the cation, resulting in decrease of effective interaction of ligand with the metal ion.

  13. Difference of coordination between alkali- and alkaline-earth-metal ions to a symmetrical α,α',δ,δ'-tetramethylcucurbit[6]uril.

    Science.gov (United States)

    Chen, Wen-Jian; Yu, Da-Hai; Xiao, Xin; Zhang, Yun-Qian; Zhu, Qian-Jiang; Xue, Sai-Feng; Tao, Zhu; Wei, Gang

    2011-08-01

    To explore differences in coordination between alkali- and alkaline-earth-metal ions and cucurbit[n]urils, a water-soluble α,α',δ,δ'-tetramethylcucurbit[6]uril (TMeQ[6]) was used to synthesize a series of complexes and their supramolecular assemblies, based on the coordination of TMeQ[6] with alkali- and alkaline-earth-metal ions. The complexes and corresponding supramolecular assemblies were structurally characterized by single-crystal X-ray diffraction. Unlike cucurbituril (Q[6]), which formed the metal-Q[6] polymers based on the direct coordination of carbonyl oxygen atoms to the alkali-metal ions, TMeQ[6] formed metal-TMeQ[6] polymers based on the direct coordination of carbonyl oxygen atoms with the alkaline-earth-metal ions rather than the alkali-metal ions.

  14. Energetics and bonding in aluminosilicate rings with alkali metal and alkaline-earth metal charge-compensating cations.

    Science.gov (United States)

    Gatti, Carlo; Ottonello, Giulio; Richet, Pascal

    2012-08-23

    The stabilizing effect of alkali and alkaline-earth metal ions on the oxygen donors of four- and six-membered faujausite-like rings has been calculated in terms of Kohn-Sham core-level (O1s) energy shifts with respect to these same complexes without cations. The results confirm and complement earlier investigations by Vayssilov and co-workers where Na(+) and K(+) were the only complexing cations. The oxygen donor centers in six-membered rings are stabilized by -3.6 ± 0.4, -3.9 ± 0.5, -7.3 ± 0.1, and -7.6 ± 0.2 eV by K(+), Na(+), Ca(2+), and Mg(2+) adions, respectively. The energy shifts are even greater for four-membered rings where the stabilization effects attain -3.7 ± 0.1, -4.1 ± 0.1, -8.1 ± 0.1, and -9.0 ± 0.1 eV, respectively. These effects are also observed on the low-lying σ-bonding and antibonding molecular orbitals (MOs) of the oxygen framework, but in a less systematic fashion. Clear relationships with the core-level shifts are found when the effects of alkali metal complexation are evaluated through electron localization/delocalization indices, which are defined in terms of the whole wave function and not just of the individual orbitals. Complexation with cations not only involves a small but significant electron sharing of the cation with the oxygen atoms in the ring but also enhances electron exchange among oxygen atoms while reducing that between the O atoms and the Si or Al atoms bonded to them. Such changes slightly increase from Na to K and from Mg to Ca, whereas they are significantly enhanced for alkaline-earth metals relative to alkali metals. With respect to Al-free complexes, Si/Al substitution and cation charge compensation generally enhance electron delocalization among the O atoms, except between those that are linked through an Al atom, and cause either an increased or a decreased Si-O ionicity (smaller/higher electron exchange) depending on the position of O in the chain relative to the Al atom(s). The generally increased

  15. Synthesis of monomeric and polymeric alkali and alkaline earth metal complexes using a phosphinoselenoic amide ligand in metal coordination sphere

    Indian Academy of Sciences (India)

    Jayeeta Bhattacharjee; Ravi K Kottalanka; Harinath Adimulam; Tarun K Panda

    2014-09-01

    We report the monomeric complexes of magnesium and calcium of composition [M(THF){2-Ph2P(Se)N(CMe3)}2] [M= Mg (3), n = 1 andM = Ca (4), n = 2)] and polymeric complexes of potassium and barium of composition [K(THF)2{Ph2P(Se)N(CMe3)}] (2) and [K(THF)Ba{Ph2P(Se)N(CMe3)}3](5) respectively. The potassium complex 2 was readily prepared by the reaction of potassium bis(trimethylsilyl)amide with phosphinoselenoic amide ligand (1) at ambient temperature. The calcium complex 4 was prepared by two synthetic routes: in the first method, commonly known as salt metathesis reaction, the potassium complex 2 was made to react with alkaline earth metal diiodide at room temperature to afford the corresponding calcium complex. The metal bis(trimethylsilyl)amides were made to react with protic ligand 1 in the second method to eliminate the volatile bis(trimethyl)silyl amine. The magnesium complex 3 and barium complex 5 were prepared only through the first method. Solid-state structures of all the new complexes were established by single crystal X-ray diffraction analysis. The smaller ionic radii of Mg2+ (0.72Å) and Ca2+ (0.99Å) ions form the monomeric complex, whereas the larger ions K+ (1.38Å) and Ba2+ (1.35Å) were found to form onedimensional polymeric complexes with monoanionic ligand 1. Compound 2 serves an example of magnesium complex with a Mg-Se direct bond.

  16. Catalysis by alkali and alkaline-earth metal ions in nucleophilic attack of methoxide ion on crown ethers bearing an intra-annular acetoxy group

    NARCIS (Netherlands)

    Cacciapaglia, Roberta; Lucente, Silvia; Mandolini, Luigi; Doorn, van Arie R.; Reinhoudt, David N.; Verboom, Willem

    1989-01-01

    Rates of reaction of methoxide ion with crown ethers bearing an intra-annular acetoxy group are markedly enhanced by alkali and alkaline-earth metal bromides as a result of much stronger interactions of the metal ions with transition states than with reactants. Rates of reactions of methoxide ion w

  17. Structural diversity in binuclear complexes of alkaline earth metal ions with 4,6-diacetylresorcinol

    Science.gov (United States)

    Shebl, Magdy; Khalil, Saied M. E.; Taha, A.; Mahdi, M. A. N.

    2012-11-01

    A new series of binuclear and mixed-ligand complexes with the general formula: [M 2(LO)yClz]; where M = Mg(II), Ca(II), Sr(II) and Ba(II); H2L = 4,6-diacetylresorcinol, the secondary ligand L' = acetylacetone (acac), 8-hydroxyquinoline (8-HQ) or 2,2'-bipyridyl (Bipy), n = 0-2, m = 1, 2, x = 0, 1, 2, 4, y = 0, 2, 4, 5 and z = 0-2; have been synthesized. They have been characterized by the analytical and spectral methods (IR, 1H NMR and mass) as well as TGA and molar conductivity measurements. The spectroscopic and conductance data suggested that the H2L ligand behaves as a neutral, monobasic or dibasic tetradentate ligand, depending on the basicity of the secondary ligand, through the two phenolic and two carbonyl groups. Binuclear octahedral geometry has been assigned to all of the prepared complexes in various molar ratios 2:2; 2:2:2; 1:2:1 and 1:2:4 (L:M:L'). Molecular orbital calculations were performed for the ligands and their complexes using Hyperchem 7.52 program on the bases of PM3 level and the results were correlated with the experimental data. The ligand and some of its alkaline metal(II) complexes showed antibacterial activity towards some of Gram-positive and Gram-negative bacteria, yeast (Candida albicans) and fungus (Aspergillus fumigatus).

  18. Prospects for sympathetic cooling of polar molecules: NH with alkali-metal and alkaline-earth atoms--a new hope.

    Science.gov (United States)

    Soldán, Pavel; Zuchowski, Piotr S; Hutson, Jeremy M

    2009-01-01

    We explore the potential energy surfaces for NH molecules interacting with alkali-metal and alkaline-earth atoms using highly correlated ab initio electronic structure calculations. The surfaces for interaction with alkali-metal atoms have deep wells dominated by covalent forces. The resulting strong anisotropies will produce strongly inelastic collisions. The surfaces for interaction with alkaline-earth atoms have shallower wells that are dominated by induction and dispersion forces. For Be and Mg the anisotropy is small compared to the rotational constant of NH, so that collisions will be relatively weakly inelastic. Be and Mg are thus promising coolants for sympathetic cooling of NH to the ultracold regime.

  19. Solvent Extraction of Alkaline Earth Metals with Alkylphosphorus Acids%有机磷(膦)酸对碱土金属的萃取

    Institute of Scientific and Technical Information of China (English)

    许新; 朱屯

    2002-01-01

    Solvent extraction equilibria of four main alkaline earth metals (magnesium, calcium, strontium and barium) with di(2-ethylhexyl) phosphoric acid (DEHPA), 2-ethylhexyl phosphonic acid mono-(2-ethylhexyl) ester,di(2,4,4-tri-methylpentyl) phosphinic acid and IR spectra of the extracts have been studied. The selectivity order is dependent on the e/r value and hydration energy of the metal ions. The minor shift of the P-O in IR absorption of the alkaline earth metal extracts indicates that the interaction between the metal ions and P-O is much weaker for alkaline earth metals than for transitional metals. The distribution of the four alkaline earth elements between aqueous solutions and solutions of DEHPA and neutral organophosphorus compounds, tri-n-butyl phosphate (TBP) or tri-octyl phosphine oxide (TOPO) in kerosene have been determined at varying ratio of TBP or TOPO to DEHPA and the positive synergism is observed. The synergic effect is explained by using IR spectra of the loaded organic phase.

  20. Effects of Alkali and Alkaline Earth Metals on N-Containing Species Release during Rice Straw Pyrolysis

    Directory of Open Access Journals (Sweden)

    Pan Gao

    2015-11-01

    Full Text Available To study the effects of inherent and external alkali and alkaline earth metallic species (AAEMs, i.e., K, Ca and Mg on the behavior of N-containing species release during rice straw (RS pyrolysis, different pretreatments were applied in numerous experiments. Results indicate that ammonia (NH3 and hydrogen cyanide (HCN are the major N-containing species and that the yields of isocyanic acid (HNCO and nitric oxide (NO are relatively low. The removal of inhert AAEMs shifts N-containing species release to a high-temperature zone according to volatile release behavior because of the increase in activation energy. The formation selectivity of NH3, HNCO, and NO increases by demineralized pretreatment, whereas HCN selectivity decreases. The formation of HNCO is mainly affected by alkaline earth metal. N-containing species release occurs in low temperatures with the addition of external AAEMs. The activation energy of samples impregnated with CaCl2 and MgCl2 sharply decreases compared to the original RS. The total yields of N-containing species are reduced significantly in the presence of KCl, CaCl2, and MgCl2 as additives. The inhibition ability of AAEMs follows the sequence MgCl2 > CaCl2 > KCl. The inhibition effect of MgCl2 can be improved by solution immersion compared with solid powder mixing. The clean biomass pyrolysis and gasification technology with low N-containing species content may be developed according to the results.

  1. Oxidation catalysts on alkaline earth supports

    Energy Technology Data Exchange (ETDEWEB)

    Mohajeri, Nahid

    2017-03-21

    An oxidation catalyst includes a support including particles of an alkaline earth salt, and first particles including a palladium compound on the support. The oxidation catalyst can also include precious metal group (PMG) metal particles in addition to the first particles intermixed together on the support. A gas permeable polymer that provides a continuous phase can completely encapsulate the particles and the support. The oxidation catalyst may be used as a gas sensor, where the first particles are chemochromic particles.

  2. sup 29 Si magic angle spinning NMR spectra of alkali metal, alkaline earth metal, and rare earth metal ion exchanged Y zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Chao, Kueijung; Chern, Jeryoung (Tsinghua Univ., Taiwan (China))

    1989-02-23

    The variation of the extraframework cation location in groups IA and IIA metals and rare earth metal (RE) Y zeolites as a function of the dehydration and the rehydration is monitored by {sup 29}Si MAS NMR. Unheated hydrated zeolites give similar {sup 29}Si spectra as they present the similar cation distributions. Upon dehydration a high-field shift is observed which correlates with the distortion of bond angles in silicon-oxygen tetrahedra. The line shapes of {sup 29}Si spectra depend on the nature and the location of the exchangeable cations and the occupancy of the different sites in dehydrated and rehydrated states. The correlation between the line shape of {sup 29}Si spectra and the migration of cations from the supercages to the sodalite cages after heating treatment was studied. The results of {sup 29}Si NMR agree with the known structure data.

  3. A preorganized metalloreceptor for alkaline earth ions showing calcium versus magnesium selectivity in water: biological activity of selected metal complexes.

    Science.gov (United States)

    Amatori, Stefano; Ambrosi, Gianluca; Fanelli, Mirco; Formica, Mauro; Fusi, Vieri; Giorgi, Luca; Macedi, Eleonora; Micheloni, Mauro; Paoli, Paola; Rossi, Patrizia

    2014-08-25

    The N,N'-bis[(3-hydroxy-4-pyron-2-yl)methyl]-N,N'-dimethylethylendiamine (Malten = L) forms the highly stable [CuH(-2)L] species in water, in which the converging maltol oxygen atoms form an electron-rich area able to host hard metal ions. When considering the alkaline earth series (AE), the [Cu(H(-2)L)] species binds all metal ions, with the exception of Mg(2+), exhibiting the relevant property to discriminate Ca(2+) versus Mg(2+) at physiological pH 7.4; the binding of the AE metal is visible to the naked eye. The stability constant values of the trinuclear [AE{Cu(H(-2)L)}2](2+) species formed reach the maximum for Ca(2+) (log K=7.7). Ca(2+) also forms a tetranuclear [Ca{Cu(H(-2)L)}]2(4+) species at a high Ca(2+) concentration. Tri- and tetranuclear calcium complexes show blue- and pink-colored crystals, respectively. [Cu(H(-2)L)] is the most active species in inducing DNA alterations. The DNA damages are compatible with its hydrolytic cleavages.

  4. Effect of metal cation replacement on the electronic structure of metalorganic halide perovskites: Replacement of lead with alkaline-earth metals

    Science.gov (United States)

    Pazoki, Meysam; Jacobsson, T. Jesper; Hagfeldt, Anders; Boschloo, Gerrit; Edvinsson, Tomas

    2016-04-01

    Organic and inorganic lead halogen perovskites, and in particular, C H3N H3Pb I3 , have during the last years emerged as a class of highly efficient solar cell materials. Herein we introduce metalorganic halogen perovskite materials for energy-relevant applications based on alkaline-earth metals. Based on the classical notion of Goldschmidt's rules and quantum mechanical considerations, the three alkaline-earth metals, Ca, Sr, and Ba, are shown to be able to exchange lead in the perovskite structure. The three alkaline-earth perovskites, C H3N H3Ca I3,C H3N H3Sr I3 , and C H3N H3Ba I3 , as well as the reference compound, C H3N H3Pb I3 , are in this paper investigated with density functional theory (DFT) calculations, which predict these compounds to exist as stable perovskite materials, and their electronic properties are explored. A detailed analysis of the projected molecular orbital density of states and electronic band structure from DFT calculations were used for interpretation of the band-gap variations in these materials and for estimation of the effective masses of the electrons and holes. Neglecting spin-orbit effects, the band gap of MACa I3,MASr I3 , and MABa I3 were estimated to be 2.95, 3.6, and 3.3 eV, respectively, showing the relative change expected for metal cation exchange. The shifts in the conduction band (CB) edges for the alkaline-earth perovskites were quantified using scalar relativistic DFT calculations and tight-binding analysis, and were compared to the situation in the more extensively studied lead halide perovskite, C H3N H3Pb I3 , where the change in the work function of the metal is the single most important factor in tuning the CB edge and band gap. The results show that alkaline-earth-based organometallic perovskites will not work as an efficient light absorber in photovoltaic applications but instead could be applicable as charge-selective contact materials. The rather high CB edge and the wide band gap together with the large

  5. Size of the fragment for crystal cluster SCF-X/sub /-SW calculations of alkaline earth metal oxides

    Energy Technology Data Exchange (ETDEWEB)

    Lobach, V.A.; Sobolev, A.B.; Shul' gin, B.V.

    Calculation of (A/sub x/B/sub y/) (x=1, 13; y=6, 14) clusters, corresponding to ideal crystals of alkaline earth metal oxides (AEMO) MgO, CaO, SrO by means of molecular cluster (MC) and crystal cluster (CC) SCF-X/sub /-SW method is carried out. MC method is not suitable for description of ideal AEMO electron structure due to long-range Coulomb interaction and potential cluster effect. Even in CC method at x < 13 and y < 14 (A/sub x/B/sub y/) cluster nonstoichiometry is inhibitory to the obtaining of satisfactory agreement with the experimental optical and X-ray spectra. (A13B14) and (B13A14) clusters satisfactorily reproduce partial composition of valence band (VB) and conduction band (CB), VB and CB widths, a fine structure of oxygen K-emission spectra in MgO and also experimental distribution of electron density. Sphere radii variation effect on the value of intersphere region error with muffin-tin averaging is considered.

  6. Fates and roles of alkali and alkaline earth metal species during the pyrolysis and gasification of a Victorian lignite

    Energy Technology Data Exchange (ETDEWEB)

    Mody, D.; Wu, H.; Li, C. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

    2000-07-01

    The transformation of alkali and alkaline earth metal (AAEM) species in a Victorian lignite during the pyrolysis and subsequent gasification in CO{sub 2} was studied in a novel quartz fluidised-bed reactor. Lignite samples prepared by physically adding NaCl and ion-exchanging Na{sup +} and Ca{sup ++} into the lignite were used to investigate the effects of chemical forms and valency of the AAEM species in the substrate lignite on their transformation during pyrolysis and gasification. Carboxyl-bound Na was found to be less volatile than Na present as NaCl, but more volatile than carboxyl-bound Ca during pyrolysis at temperatures between 400 and 900{sup o}C. However, the carboxyl-bound Na was volatilised to a much greater extent than the carboxyl-bound Ca in the same lignite during pyrolysis. It was seen that the loading of NaCl into the lignite did not significantly affect the char reactivity in the fluidised-bed reactor at 900{sup o}C.

  7. Selective oxidation of methanol to hydrogen over gold catalysts promoted by alkaline-earth-metal and lanthanum oxides.

    Science.gov (United States)

    Hereijgers, Bart P C; Weckhuysen, Bert M

    2009-01-01

    A series of alumina-supported gold catalysts was investigated for the CO-free production of hydrogen by partial oxidation of methanol. The addition of alkaline-earth metal oxide promoters resulted in a significant improvement of the catalytic performance. The methanol conversion was ca. 85 % with all studied catalyst materials, however, the selectivity for hydrogen increased from 15 % to 51 % when going from the unpromoted to a BaO-promoted catalyst. The formation of the undesired byproducts CO, methane, and dimethyl ether was considerably reduced as well. The observed trend in catalyst performance follows the trend in increasing basicity of the studied promoter elements, indicating a chemical effect of the promoter material. Superior catalytic performance, in terms of H(2) and CO selectivity, was obtained with a Au/La(2)O(3) catalyst. At 300 degrees C the hydrogen selectivity reached 80 % with only 2 % CO formation, and the catalyst displayed a stable performance over at least 24 h on-stream. Furthermore, the formation of CO was found to be independent of the oxygen concentration in the feed. The commercial lanthanum oxide used in this study had a low specific surface area, which led to the formation of relative large gold particles. Therefore, the catalytic activity could be enhanced by decreasing the gold particle size through deposition on lanthanum oxide supported on high-surface-area alumina.

  8. Thin-layer chromatographie separation of alkaline earth metals on diethylaminoethyl cellulose.

    Science.gov (United States)

    Ishida, K

    1969-12-01

    Thin-layer Chromatographic behaviour of magnesium, calcium, strontium and barium on diethylaminoethyl cellulose has been investigated in methanol-nitric acid mixtures. R(f) values are in the order magnesium > calcium > strontium > barium. The differences in R(f) values are large enough to allow good separations of the four metal ions from each other. The best separation is obtained by the ascending technique with methanol-8M nitric acid (20:1, v v ).

  9. 1H and 23Na MAS NMR spectroscopy of cationic species in CO2 selective alkaline earth metal porous silicoaluminophosphates prepared via liquid and solid state ion exchange

    Science.gov (United States)

    Arévalo-Hidalgo, Ana G.; Dugar, Sneha; Fu, Riqiang; Hernández-Maldonado, Arturo J.

    2012-07-01

    The location of extraframework cations in Sr2+ and Ba2+ ion-exchanged SAPO-34 was estimated by means of 1H and 23Na MAS NMR spectroscopy and spectral deconvolution. Incorporation of the alkaline earth metal cations onto the SAPO framework was achieved via liquid state ion exchange, coupled partial detemplation/solid-state ion exchange, and combination of both techniques. MAS NMR revealed that the level of ion exchange was limited by the presence of protons and sodium cations near hexagonal prisms (site SI), which are relatively difficult to exchange with the alkaline earth metal due to steric and charge repulsion criteria. In addition, the presence of ammonium cations in the supercages facilitated the exchange of otherwise tenacious hydrogen as corroborated by unit cell compositional data as well as enhanced CO2 adsorption at low partial pressures. The extraframework ammonium species were produced from partial detemplation of the structure-directing agent employed for the SAPO-34 synthesis, tetraethylammonium.

  10. FTIR AND SOME PHYSICAL PROPERTIES OF ALKALINE EARTH BORATE GLASSES CONTAINING HEAVY METAL OXIDES

    Directory of Open Access Journals (Sweden)

    RAMADEVUDU.G

    2011-09-01

    Full Text Available The FTIR spectra of heavy metal oxide doped borate glasses with the general formula RO-MO-B2O3 (RO= MgO, CaO, SrO and BaO, MO=ZnO, TeO2, PbO and Bi2O3 were studied in the spectral range 400-4400cm-1 toobtain information about the influence of the glass composition on the spectra. The FTIR studies revealed that MO acted differently in RO-B2O3 glass matrix and produced small variations in the glass structure. RO oxides also affected the glass structure slightly due to mixed oxide effect. However the structural groupings present ineach series of glasses are not much affected by the composition. The effect of composition on some physical properties like density, molar volume was also carried out. The increase in the values of physical parameters such as density and glass transition temperature is attributed to conversion of [BO3]3- triangular units into BO4-tetrahedral units.

  11. Alkaline earth metal-based metal-organic framework: hydrothermal synthesis, X-ray structure and heterogeneously catalyzed Claisen-Schmidt reaction.

    Science.gov (United States)

    Saha, Debraj; Maity, Tanmoy; Koner, Subratanath

    2014-09-14

    Two alkaline earth metal-based carboxylate systems, [Mg(HL)(H2O)2]n (1) and [Ca(H2L)2]n (2) (H3L = chelidamic acid) have been hydrothermally synthesized, and characterized by single-crystal X-ray diffraction, IR, elemental analysis, and thermo-gravimetric analysis. Compound 1 has a 2D structure incorporating two water molecules. The dehydrated species, 1a, generated from 1 by removal of the coordinated water, has been characterized by thermo-gravimetric analysis, IR, elemental analysis and variable temperature powder X-ray diffraction. Both 1 and its dehydrated species 1a catalyze the Claisen-Schmidt reaction under heterogeneous conditions, but 1a is a more effective catalyst under environmentally friendly conditions. The catalyst can readily be recovered and reused in successive cycles without detectable loss of activity. Compound 2 has a 3D structure and is thermally stable up to 540 °C, but is inactive catalytically.

  12. Ab Initio Quantum Mechanical Study of the Structure and Stability of the Alkaline Earth Metal Oxides and Peroxides

    Science.gov (United States)

    Königstein, Markus; Catlow, C. Richard A.

    1998-10-01

    We report a detailed computationally study of the stability of the alkaline earth metal peroxidesMO2(M=Ba, Sr, Ca, Mg, Be) with respect to decomposition into the corresponding oxidesMOand molecular oxygen using Hartree-Fock and density functional theory (DFT) techniques. A comparison between calculated and experimental binding energies indicates that the DFT method is most suitable for a correct description of the peroxide bond. The DFT reaction energies for the peroxide decompositionMO2→MO+{1}/{2}O2show that only BaO2and SrO2are thermodynamically stable compounds, while CaO2(in the calcium carbide structure), MgO2, and BeO2(in the pyrite structure) are energetically unstable with reaction energies of -24.7, -26.8, and -128.7kJ/mol, respectively, and are therefore unlikely to exist as pure compounds. The published calcium carbide structure for CaO2is probably incorrect, at least for pure calcium peroxide, since apart from the thermodynamical instability the compound is more stable in the pyrite structure by 25.5 kJ/mol. Our analysis suggests that the water and/or hydrogen peroxide content of experimentally prepared MgO2samples is necessary for the stabilization of the structure, while BeO2is clearly unstable under ambient conditions. We studied also the effect of the zero point energies and the entropies on the decomposition free energies and, for this purpose, performed atomistic lattice simulations based on interatomic potentials, which we derived from ourab initiodata; the results indicate a negligible effect of the zero point energies, while the entropy terms favor the decomposition reaction by ca. 20 kJ/mol at 298.15 K.

  13. Ab initio quantum mechanical study of the structure and stability of the alkaline earth metal oxides and peroxides

    Energy Technology Data Exchange (ETDEWEB)

    Koenigstein, M.; Catlow, C.R.A. [Royal Institution of Great Britain, London (United Kingdom). Davy Faraday Research Lab.

    1998-10-01

    The authors report a detailed computational study of the stability of the alkaline earth metal peroxides MO{sub 2} (M = Ba, Sr, Ca, Mg, Be) with respect to decomposition into the corresponding oxides Mo and molecular oxygen using Hartree-Fock and density functional theory (DFT) techniques. A comparison between calculated and experimental binding energies indicates that the DFT method is most suitable for a correct description of the peroxide bond. The DFT reaction energies for the peroxide decomposition MO{sub 2} {yields} MO + {1/2}O{sub 2} show that only BaO{sub 2} and SrO{sub 2} are thermodynamically stable compounds, while CaO{sub 2} (in the calcium carbide structure), MgO{sub 2}, and BeO{sub 2} (in the pyrite structure) are energetically unstable with reaction energies of {minus}24.7, {minus}26.8, and {minus}128.7 kJ/mol, respectively, and are therefore unlikely to exist as pure compounds. The published calcium carbide structure for CaO{sub 2} is probably incorrect, at least for pure calcium peroxide, since apart from the thermodynamical instability the compound is more stable in the pyrite structure by 25.5 kJ/mol. The analysis suggests that the water and/or hydrogen peroxide content of experimentally prepared MgO{sub 2} samples is necessary for the stabilization of the structure, while BeO{sub 2} is clearly unstable under ambient conditions. The authors studied also the effect of the zero point energies and the entropies on the decomposition free energies and, for this purpose, performed atomistic lattice simulations based on interatomic potentials, which they derived from their ab initio data; the results indicate a negligible effect of the zero point energies, while the entropy terms favor the decomposition reaction by ca. 20 kJ/mol at 298.15 K.

  14. Adsorption of alkali, alkaline-earth, simple and 3d transition metal, and nonmetal atoms on monolayer MoS2

    Directory of Open Access Journals (Sweden)

    X. D. Li

    2015-05-01

    Full Text Available Single adsorption of different atoms on pristine two-dimensional monolayer MoS2 have been systematically investigated by using density functional calculations with van der Waals correction. The adatoms cover alkali metals, alkaline earth metals, main group metal, 3d-transition metals, coinage metal and nonmetal atoms. Depending on the adatom type, metallic, semimetallic or semiconducting behavior can be found in direct bandgap monolayer MoS2. Additionally, local or long-range magnetic moments of two-dimensional MoS2 sheet can also attained through the adsorption. The detailed atomic-scale knowledge of single adsorption on MoS2 monolayer is important not only for the sake of a theoretical understanding, but also device level deposition technological application.

  15. Structures and Spectroscopy Studies of Two M(II-Phosphonate Coordination Polymers Based on Alkaline Earth Metals (M = Ba, Mg

    Directory of Open Access Journals (Sweden)

    Kui-Rong Ma

    2013-01-01

    Full Text Available The two examples of alkaline-earth M(II-phosphonate coordination polymers, [Ba2(L(H2O9]·3H2O (1 and [Mg1.5(H2O9]·(L-H21.5·6H2O (2 (H4L = H2O3PCH2N(C4H8NCH2PO3H2, N,N′-piperazinebis(methylenephosphonic acid, (L-H2 = O3PH2CHN(C4H8NHCH2PO3 have been hydrothermally synthesized and characterized by elemental analysis, FT-IR, PXRD, TG-DSC, and single-crystal X-ray diffraction. Compound 1 possesses a 2D inorganic-organic alternate arrangement layer structure built from 1D inorganic chains through the piperazine bridge, in which the ligand L−4 shows two types of coordination modes reported rarely at the same time. In 1, both crystallographic distinct Ba(1 and Ba(2 ions adopt 8-coordination two caps and 9-coordination three caps triangular prism geometry structures, respectively. Compound 2 possesses a zero-dimensional mononuclear structure with two crystallographic distinct Mg(II ions. Free metal cations   [MgO6]n2+ and uncoordinated anions (L-H2n2- are joined together by static electric force. Results of photoluminescent measurement indicate three main emission bands centered at 300 nm, 378.5 nm, and 433 nm for 1 and 302 nm, 378 nm, and 434.5 nm for 2 (λex=235 nm, respectively. The high energy emissions could be derived from the intraligand π∗-n transition stations of H4L (310 nm and 382 nm, λex=235 nm, while the low energy emission (>400 nm of 1-2 may be due to the coordination effect with metal(II ions.

  16. Microcalorimetric study on host-guest complexation of naphtho-15-crown-5 with four ions of alkaline earth metal

    Institute of Scientific and Technical Information of China (English)

    SONG Ming-zhi; ZHU Lan-ying; GAO Xi-ke; DOU Jian-min; SUN De-zhi

    2005-01-01

    Thermodynamic parameters of complexation of naphto- 15-crown-5 with four alkaline earth ions in aqueous media was determined using titration microcalorimetry at 298.15 K. The stability of the complexes, thermal effect and entropy effect of the complexation is discussed on the basis of the guest ions structure and the solvent effect. The stability constants tendency to vary with ion radius was interpreted. Complex of naphtha-15-crown-5 with calcium ion is very stable due to the synergism of static electric interaction and size selectivity between the host and the guest.

  17. Comparisons between adsorption and diffusion of alkali, alkaline earth metal atoms on silicene and those on silicane: Insight from first-principles calculations

    Science.gov (United States)

    Bo, Xu; Huan-Sheng, Lu; Bo, Liu; Gang, Liu; Mu-Sheng, Wu; Chuying, Ouyang

    2016-06-01

    The adsorption and diffusion behaviors of alkali and alkaline-earth metal atoms on silicane and silicene are both investigated by using a first-principles method within the frame of density functional theory. Silicane is staler against the metal adatoms than silicene. Hydrogenation makes the adsorption energies of various metal atoms considered in our calculations on silicane significantly lower than those on silicene. Similar diffusion energy barriers of alkali metal atoms on silicane and silicene could be observed. However, the diffusion energy barriers of alkali-earth metal atoms on silicane are essentially lower than those on silicene due to the small structural distortion and weak interaction between metal atoms and silicane substrate. Combining the adsorption energy with the diffusion energy barriers, it is found that the clustering would occur when depositing metal atoms on perfect hydrogenated silicene with relative high coverage. In order to avoid forming a metal cluster, we need to remove the hydrogen atoms from the silicane substrate to achieve the defective silicane. Our results are helpful for understanding the interaction between metal atoms and silicene-based two-dimensional materials. Project supported by the Natural Science Foundation of Jiangxi Province, China (Grant Nos. 20152ACB21014, 20151BAB202006, and 20142BAB212002) and the Fund from the Jiangxi Provincial Educational Committee, China (Grant No. GJJ14254). Bo Xu is also supported by the Oversea Returned Project from the Ministry of Education, China.

  18. Luminescence behaviors of Eu- and Dy-codoped alkaline earth metal aluminate phosphors through potassium carbonate coprecipitation

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Chen-Jui, E-mail: cjliang@fcu.edu.tw; Siao, Hao-Yi

    2016-07-01

    An electronic energy mechanism of activator and sensitizer was established to describe the luminescence behaviors of Eu- and Dy-codoped M(II)Al{sub 2}O{sub 4} (M(II) = Ba, Sr, Ca, Mg) phosphors through potassium carbonate coprecipitation. Experimental results demonstrated that the prepared phosphors exhibited superior crystallinity at a temperature lower than 950 °C. The phosphors are ordered according to emission intensity as follows Ca- > Ba- > Sr- > Mg-containing phosphors. The energy level for Eu{sup 2+} 4f{sup 6}5d{sup 1} → 4f{sup 7}, Eu{sup 3+4}D{sub 0} → {sup 7}F, and Dy{sup 3+4}F{sub 9/2} → {sup 6}H transitions and the effects of nephelauxetic and crystal field in Ba-, Sr-, and Ca-containing phosphors were discussed. The energy gap, (hv){sub em}, between 5d and 4f of Eu{sup 2+} ion is strongly affected by host composition, crystal field strength, and nephelauxetic effect. The infrared emission of 4f{sub 9/2} → 6h for Dy{sup 3+} is merely depend on the transfer of energy from Eu{sup 2+} upon excited. Ca-containing phosphor with maximum (hv){sub em} is attributed to the lowest bond length of Ca−O and highest ionization potential of Ca{sup 2+} ion, which leads to the effects of crystal field and nephelauxetic greater than that in the other phosphors. - Highlights: • The list of the collected figure captions: • Develop a new coprecipitation method to prepare high efficiency phosphors. • Obtain superior crystallinity with lower calcination temperature. • Luminescence behavior of Eu- and Dy-codoped on aluminate phosphors is discussed. • Investigate the effects of alkaline earth metal containing on crystal field and nephelauxetic.

  19. The influence of alkaline earth metal equilibria on the rheological, melting and textural properties of Cheddar cheese.

    Science.gov (United States)

    Cooke, Darren R; McSweeney, Paul L H

    2013-11-01

    The total calcium content of cheese, along with changes in the equilibrium between soluble and casein (CN)-bound calcium during ripening can have a major impact on its rheological, functional and textural properties; however, little is known about the effect of other alkaline earth metals. NaCl was partially substituted with MgCl2 or SrCl2 (8·7 and 11·4 g/kg curd, respectively) at the salting stage of cheesemaking to study their effects on cheese. Three cheeses were produced: Mg supplemented (+Mg), Sr supplemented (+Sr) and a control Cheddar cheese. Ca, Mg and Sr contents of cheese and expressible serum obtained therefrom were determined by atomic absorption spectroscopy. Addition of Mg2+ or Sr2+ had no effect on % moisture, protein, fat and extent of proteolysis. A proportion of the added Mg2+ and Sr2+ became CN-bound. The level of CN-bound Mg was higher in the +Mg cheese than the control throughout ripening. The level of CN-bound Ca and Mg decreased during ripening in all cheeses, as did % CN-bound Sr in the +Sr cheese. The presence of Sr2+ increased % CN-bound Ca and Mg at a number of ripening times. Adding Mg2+ had no effect on % CN-bound Ca. The +Sr cheese exhibited a higher G' at 70 °C and a lower LTmax than the control and +Mg cheeses throughout ripening. The +Sr cheese had significantly lower meltability compared with the control and +Mg cheeses after 2 months of ripening. Hardness values of the +Sr cheese were higher at week 2 than the +Mg and control cheeses. Addition of Mg2+ did not influence the physical properties of cheese. Supplementing cheese with Sr appeared to have effects analogous to those previously reported for increasing Ca content. Sr2+ may form and/or modify nanocluster crosslinks causing an increase in the strength of the para-casein matrix.

  20. Dipole Polarizability of Alkali-Metal (Na, K, Rb) - Alkaline-Earth-Metal (Ca,Sr) Polar molecules - Prospects of Alignment

    CERN Document Server

    Gopakumar, Geetha; Hada, Masahiko; Kajita, Masatoshi

    2014-01-01

    Electronic open-shell ground-state properties of selected alkali-metal (AM) - alkaline-earth-metal (AEM) polar molecules are investigated. We determine potential energy curves of the 2{\\Sigma}+ ground state at the coupled-cluster singles and doubles with partial triples (CCSD(T)) level of electron correlation. Calculated spectroscopic constants for the isotopes (23Na, 39K, 85Rb) - (40Ca, 88Sr) are compared with available theoretical and experimental results. The variation of the permanent dipole moment (PDM), average dipole polarizability, and polarizability anisotropy with internuclear distance is determined using finite-field perturbation theory at the CCSD(T) level. Owing to moderate PDM (KCa: 1.67 D, RbCa: 1.75 D, KSr: 1.27 D, RbSr: 1.41 D) and large polarizability anisotropy (KCa: 566 a.u., RbCa: 604 a.u., KSr: 574 a.u., RbSr: 615 a.u.), KCa, RbCa, KSr, and RbSr are potential candidates for alignment and orientation in combined intense laser and external static electric fields.

  1. Enhanced Electroresponse of Alkaline Earth Metal-Doped Silica/Titania Spheres by Synergetic Effect of Dispersion Stability and Dielectric Property.

    Science.gov (United States)

    Yoon, Chang-Min; Lee, Seungae; Cheong, Oug Jae; Jang, Jyongsik

    2015-09-01

    A series of alkaline earth metal-doped hollow SiO2/TiO2 spheres (EM-HST) are prepared as electrorheological (ER) materials via sonication-mediated etching method with various alkaline earth metal hydroxides as the etchant. The EM-HST spheres are assessed to determine how their hollow interior and metal-doping affects the ER activity. Both the dispersion stability and the dielectric properties of these materials are greatly enhanced by the proposed one-step etching method, which results in significant enhancement of ER activity. These improvements are attributed to increased particle mobility and interfacial polarization originating from the hollow nature of the EM-HST spheres and the effects of EM metal-doping. In particular, Ca-HST-based ER fluid exhibits ER performance which is 7.1-fold and 3.1-fold higher than those of nonhollow core/shell silica/titania (CS/ST) and undoped hollow silica/titania (HST)-based ER fluids, respectively. This study develops a versatile and simple approach to enhancing ER activity through synergetic effects arising from the combination of dispersion stability and the unique dielectric properties of hollow EM-HST spheres. In addition, the multigram scale production described in this experiment can be an excellent advantage for practical and commercial ER application.

  2. Origin of low sodium capacity in graphite and generally weak substrate binding of Na and Mg among alkali and alkaline earth metals.

    Science.gov (United States)

    Liu, Yuanyue; Merinov, Boris V; Goddard, William A

    2016-04-05

    It is well known that graphite has a low capacity for Na but a high capacity for other alkali metals. The growing interest in alternative cation batteries beyond Li makes it particularly important to elucidate the origin of this behavior, which is not well understood. In examining this question, we find a quite general phenomenon: among the alkali and alkaline earth metals, Na and Mg generally have the weakest chemical binding to a given substrate, compared with the other elements in the same column of the periodic table. We demonstrate this with quantum mechanics calculations for a wide range of substrate materials (not limited to C) covering a variety of structures and chemical compositions. The phenomenon arises from the competition between trends in the ionization energy and the ion-substrate coupling, down the columns of the periodic table. Consequently, the cathodic voltage for Na and Mg is expected to be lower than those for other metals in the same column. This generality provides a basis for analyzing the binding of alkali and alkaline earth metal atoms over a broad range of systems.

  3. Origin of low sodium capacity in graphite and generally weak substrate binding of Na and Mg among alkali and alkaline earth metals

    Science.gov (United States)

    Liu, Yuanyue; Merinov, Boris V.; Goddard, William A., III

    2016-04-01

    It is well known that graphite has a low capacity for Na but a high capacity for other alkali metals. The growing interest in alternative cation batteries beyond Li makes it particularly important to elucidate the origin of this behavior, which is not well understood. In examining this question, we find a quite general phenomenon: among the alkali and alkaline earth metals, Na and Mg generally have the weakest chemical binding to a given substrate, compared with the other elements in the same column of the periodic table. We demonstrate this with quantum mechanics calculations for a wide range of substrate materials (not limited to C) covering a variety of structures and chemical compositions. The phenomenon arises from the competition between trends in the ionization energy and the ion-substrate coupling, down the columns of the periodic table. Consequently, the cathodic voltage for Na and Mg is expected to be lower than those for other metals in the same column. This generality provides a basis for analyzing the binding of alkali and alkaline earth metal atoms over a broad range of systems.

  4. Chelation ion chromatography of alkaline earth and transition metals a using monolithic silica column with bonded N-hydroxyethyliminodiacetic acid functional groups.

    Science.gov (United States)

    McGillicuddy, Nicola; Nesterenko, Ekaterina P; Nesterenko, Pavel N; Jones, Phil; Paull, Brett

    2013-02-08

    A commercially available porous silica monolithic column (Onyx Monolithic Si, 100 mm×4.6 mm I.D.) was 'in-column' covalently functionalised with 2-hydroxyethyliminodiacetic acid (HEIDA) groups, and applied to the simultaneous and rapid separation of alkaline earth and transition metal ions, using high-performance chelation ion chromatography (HPCIC). With a 0.3mM dipicolinic acid (DPA) containing eluent, the baseline separation of various common transition and heavy metal ions and the four alkaline earth metal ions could be achieved in under 14 min with a flow rate of just 0.8 mL/min. Detection was achieved using spectrophotometric detection at 540 nm after post-column reaction (PCR) with 4-(2-pyridylazo)-resorcinol (PAR). Significant effects from variation of eluent nature, concentration and temperature upon selectivity and retention were demonstrated with the new monolithic silica chelating phase. Under optimised conditions (0.165 M LiNO(3) eluent, pH 2.5), peak efficiencies of 54,000, 60,000 and 64,000 N/m, for Zn(2+), Mn(2+) and Cd(2+), respectively, were recorded, far exceeding that previously reported for IDA based chelation ion exchange columns.

  5. Identifying the presence of a disulfide linkage in peptides by the selective elimination of hydrogen disulfide from collisionally activated alkali and alkaline earth metal complexes.

    Science.gov (United States)

    Kim, Hugh I; Beauchamp, J L

    2008-01-30

    We report a new method for identifying disulfide linkages in peptides using mass spectrometry. This is accomplished by collisional activation of singly charged cationic alkali and alkaline earth metal complexes, which results in the highly selective elimination of hydrogen disulfide (H2S2). Complexes of peptides possessing disulfide bonds with sodium and alkaline earth metal are generated using electrospray ionization (ESI). Isolation followed by collision induced dissociation (CID) of singly charged peptide complexes results in selective elimination of H2S2 to leave newly formed dehydroalanine residues in the peptide. Further activation of the product yields sequence information in the region previously short circuited by the disulfide bond. For example, singly charged magnesium and calcium ion bound complexes of [Lys8]-vasopressin exhibit selective elimination of H2S2 via low-energy CID. Further isolation of the product followed by CID yields major b- and z-type fragments revealing the peptide sequence in the region between the newly formed dehydroalanine residues. Numerous model peptides provide mechanistic details for the selective elimination of H2S2. The process is initiated starting with a metal stabilized enolate anion at Cys, followed by cleavage of the S-C bond. An examination of the peptic digest of insulin provides an example of the application of the selective elimination of H2S2 for the identification of peptides with disulfide linkages. The energetics and mechanisms of H2S2 elimination from model compounds are investigated using density functional theory (DFT) calculations.

  6. MB82- (M=Be,Mg,Ca,Sr,and Ba):Planar octacoordinate alkaline earth metal atoms enclosed by boron rings

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Complexes involving planar octacoordinate alkaline earth metal atoms in the centers of eight-membered boron rings have been investigated by two density functional theory (DFT) methods.BeB82-with D8h symmetry is predicted to be stable,both geometrically and electronically,since a good match is achieved between the size of the central beryllium atom and the eight-membered boron ring.By contrast,the other alkaline earth metal atoms cannot be stabilized in the center of a planar eight-membered boron ring because of their large radii.By following the out-of-plane imaginary vibrational frequency,pyramidal C8v MgB82-,CaB82-,SrB82-,and BaB82-structures are obtained.The presence of delocalized π and σ valence molecular orbitals in D8h BeB82-gives rise to aromaticity,which is reflected by the value of the nucleus-independent chemical shift.The D8h BeB82-structure is confirmed to be the global minimum on the potential energy surface.

  7. Production of Synthesis Gas via Methane Reforming with CO2 on Ni/SiO2 Catalysts Promoted by Alkali and Alkaline Earth Metals

    Institute of Scientific and Technical Information of China (English)

    陈平; 侯昭胤; 郑小明

    2005-01-01

    Ni/SiO2 catalysts promoted by alkali metals K and Cs or alkaline earth metals Mg, Ca, Sr and Ba were prepared, characterized by H2-TPR and XRD, and used for the production of synthesis gas via methane reforming with CO2. Though K and Cs promoted Ni catalysts could eliminate coke deposition, the reforming activity of these promoted catalysts was decreased heavily. Mg and Ca promoted Ni/SiO2 catalysts exhibited excellent coke resistance ability with minor loss of the reforming activity of Ni/SiO2. Ba showed poor coke resistance ability and small amount of Sr increased the formation of coke. The possible mechanism of these promoters was discussed.

  8. Promoting alkali and alkaline-earth metals on MgO for enhancing CO2 capture by first-principles calculations.

    Science.gov (United States)

    Kim, Kiwoong; Han, Jeong Woo; Lee, Kwang Soon; Lee, Won Bo

    2014-12-07

    Developing next-generation solid sorbents to improve the economy of pre- and post-combustion carbon capture processes has been challenging for many researchers. Magnesium oxide (MgO) is a promising sorbent because of its moderate sorption-desorption temperature and low heat of sorption. However, its low sorption capacity and thermal instability need to be improved. Various metal-promoted MgO sorbents have been experimentally developed to enhance the CO2 sorption capacities. Nevertheless, rigorous computational studies to screen an optimal metal promoter have been limited to date. We conducted first-principles calculations to select metal promoters of MgO sorbents. Five alkali (Li-, Na-, K-, Rb-, and Cs-) and 4 alkaline earth metals (Be-, Ca-, Sr-, and Ba-) were chosen as a set of promoters. Compared with the CO2 adsorption energy on pure MgO, the adsorption energy on the metal-promoted MgO sorbents is higher, except for the Na-promoter, which indicates that metal promotion on MgO is an efficient approach to enhance the sorption capacities. Based on the stabilized binding of promoters on the MgO surface and the regenerability of sorbents, Li, Ca, and Sr were identified as adequate promoters among the 9 metals on the basis of PW91/GGA augmented with DFT+D2. The adsorption energies of CO2 on metal-promoted MgO sorbents for Li, Ca, and Sr atoms are -1.13, -1.68, and -1.48 eV, respectively.

  9. Volatilisation of alkali and alkaline earth metallic species during the pyrolysis of biomass: differences between sugar cane bagasse and cane trash.

    Science.gov (United States)

    Keown, Daniel M; Favas, George; Hayashi, Jun-ichiro; Li, Chun-Zhu

    2005-09-01

    Sugar cane bagasse and cane trash were pyrolysed in a novel quartz fluidised-bed/fixed-bed reactor. Quantification of the Na, K, Mg and Ca in chars revealed that pyrolysis temperature, heating rate, valence and biomass type were important factors influencing the volatilisation of these alkali and alkaline earth metallic (AAEM) species. Pyrolysis at a slow heating rate (approximately 10 K min(-1)) led to minimal (often biomass samples. Fast heating rates (>1000 K s(-1)), encouraging volatile-char interactions with the current reactor configuration, resulted in the volatilisation of around 80% of Na, K, Mg and Ca from bagasse during pyrolysis at 900 degrees C. Similar behaviour was observed for monovalent Na and K with cane trash, but the volatilisation of Mg and Ca from cane trash was always restricted. The difference in Cl content between bagasse and cane trash was not sufficient to fully explain the difference in the volatilisation of Mg and Ca.

  10. Volatilisation of alkali and alkaline earth metallic species during the gasification of a Victorian brown coal in CO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Quyn, Dimple Mody; Li, Chun-Zhu [CRC for Clean Power from Lignite, Department of Chemical Engineering, PO Box 36, Monash University, Victoria 3800 (Australia); Hayashi, Jun-ichiro [Centre for Advanced Research of Energy Conversion Materials, Hokkaido University, N13-W8, Kita-ku, Sapporo 060-8628 (Japan)

    2005-08-25

    A Victorian brown coal was gasified in a bench-scale quartz fluidised-bed/fixed-bed reactor in order to study the volatilisation of Na, Ca, and Mg during devolatilisation and gasification and their roles in the reactivity of chars. It was found that the majority of Na was volatilised at 900 {sup o}C under all conditions and that a Na retention limit was achieved in the char with the progress of CO{sub 2} gasification. In some cases, the presence of CO{sub 2} during devolatilisation enhanced the Na retention in the char. In contrast, the retention of Ca (and Mg) was unaffected by CO{sub 2} during devolatilisation at 900C but decreased drastically upon nascent char gasification. The fundamental differences in volatilisation between the alkali and alkaline earth metallic species are discussed in this paper.

  11. Mechanochemical synthesis, structure, and properties of solid solutions of alkaline earth metal fluorides: Ma1-xMbxF2 (M: Ca, Sr, Ba)

    Science.gov (United States)

    Heise, M.; Scholz, G.; Düvel, A.; Heitjans, P.; Kemnitz, E.

    2016-10-01

    The capability of mechanochemical synthesis for the formation of solid solutions of alkaline earth metal fluorides Ma1-xMbxF2 (M: Ca, Sr, Ba) was tested by fluorination of metal acetates and metal hydroxides with ammonium fluoride directly at milling. Evidence was found for a mutual substitution of cations on their lattice positions in Ca1-xSrxF2 and Ba1-xSrxF2 samples. For the Ba/Ca-system this synthesis route is only partially successful. X-ray diffraction and 19F MAS NMR spectroscopy were used to characterize all samples concerning their crystal structure and local fluorine coordination. Calculations of 19F chemical shifts with the superposition model along with probability calculations for the intensity of the individual 19F lines, performed in dependence on the molar composition of the samples, perfectly agree with the experimental findings. The fluoride ion conductivity of as-prepared samples, determined by temperature dependent DC conductivity measurements, is significantly higher than those of crystalline binary fluorides. Moreover, a higher F- ion conductivity is observed for samples with higher mixing grade in the Ca/Sr-and the Ba/Sr-systems.

  12. Absorption spectroscopy of heavy alkaline earth metals Ba and Sr in rare gas matrices—CCSD(T) calculations and atomic site occupancies

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Barry M.; McCaffrey, John G., E-mail: john.mccaffrey@nuim.ie [Department of Chemistry, Maynooth University, National University of Ireland—Maynooth, County Kildare (Ireland)

    2016-01-28

    Isolation of the heavier alkaline earth metals Ba and Sr in the solid rare gases (RGs) Ar, Kr, and Xe is analysed with absorption spectroscopy and interpreted partly with the assistance of ab initio calculations of the diatomic M ⋅ RG ground state interaction potentials. The y{sup 1}P←a{sup 1}S resonance transitions in the visible spectral region are used to compare the isolation conditions of these two metal atom systems and calcium. Complex absorption bands were recorded in all three metal atom systems even after extensive sample annealing. Coupled cluster calculations conducted on the ground states of the nine M ⋅ RG diatomics (M = Ca, Sr, and Ba; RG = Ar, Kr, and Xe) at the coupled cluster single, double, and non-iterative triple level of theory revealed long bond lengths (>5 Å) and shallow bound regions (<130 cm{sup −1}). All of the M ⋅ RG diatomics have bond lengths considerably longer than those of the rare gas dimers, with the consequence that isolation of these metal atoms in a single substitutional site of the solid rare gas is unlikely, with the possible exception of Ca/Xe. The luminescence of metal dimer bands has been recorded for Ba and Sr revealing very different behaviours. Resonance fluorescence with a lifetime of 15 ns is observed for the lowest energy transition of Sr{sub 2} while this transition is quenched in Ba{sub 2}. This behaviour is consistent with the absence of vibrational structure on the dimer absorption band in Ba{sub 2} indicating lifetime broadening arising from efficient relaxation to low-lying molecular states. More extensive 2D excitation-emission data recorded for the complex site structures present on the absorption bands of the atomic Ba and Sr systems will be presented in future publications.

  13. Counterion influence on the vibrational wavenumbers in ternary and quaternary metal hydride salts, A2MH6 (A = alkali metal, alkaline earth, and lanthanides; M = Ir, Fe, Ru, Os, Pt, Mn).

    Science.gov (United States)

    Gilson, Denis F R; Moyer, Ralph O

    2012-02-06

    The wavenumbers of the ν(3) metal-hydrogen stretching mode (T(1u)) in the IR spectra of both ternary and quaternary hexahydrido salts of transition metals from groups 7 to 10 ([Mn(I)H(6)](5-), [Fe(II)H(6)](4-), [Ru(II)H(6)](4-), [Os(II)H(6)](4-), [Ir(III)H(6)](3-), and [Pt(IV)H(6)](2-)) depend linearly upon the ionization energies of the counterions (alkali metal, alkaline earth, and lanthanide) with a separate line for each metal. This relationship provides quantitative support for the charge-transfer mechanism for explaining the stabilities of these compounds.

  14. Alkaline Earth Core Level Photoemission Spectroscopy of High-Temperature Superconductors

    Science.gov (United States)

    Vasquez, R.

    1993-01-01

    This paper examines photoemission measurements of the alkaline Earth core levels of high-temperature superconductors and related materials, models that seek to explain the large negative shifts observed relative to the corresponding alkaline Earth metals, and the effect of lattice site disorder on the core level spectra and the presence or absence of intrinsic surface peaks.

  15. The Electronic Structures and Optical Properties of Alkaline-Earth Metals Doped Anatase TiO2: A Comparative Study of Screened Hybrid Functional and Generalized Gradient Approximation

    Directory of Open Access Journals (Sweden)

    Jin-Gang Ma

    2015-08-01

    Full Text Available Alkaline-earth metallic dopant can improve the performance of anatase TiO2 in photocatalysis and solar cells. Aiming to understand doping mechanisms, the dopant formation energies, electronic structures, and optical properties for Be, Mg, Ca, Sr, and Ba doped anatase TiO2 are investigated by using density functional theory calculations with the HSE06 and PBE functionals. By combining our results with those of previous studies, the HSE06 functional provides a better description of electronic structures. The calculated formation energies indicate that the substitution of a lattice Ti with an AEM atom is energetically favorable under O-rich growth conditions. The electronic structures suggest that, AEM dopants shift the valence bands (VBs to higher energy, and the dopant-state energies for the cases of Ca, Sr, and Ba are quite higher than Fermi levels, while the Be and Mg dopants result into the spin polarized gap states near the top of VBs. The components of VBs and dopant-states support that the AEM dopants are active in inter-band transitions with lower energy excitations. As to optical properties, Ca/Sr/Ba are more effective than Be/Mg to enhance absorbance in visible region, but the Be/Mg are superior to Ca/Sr/Ba for the absorbance improvement in near-IR region.

  16. Alkaline Earth Metal Zirconate Perovskites MZrO3 (M=Ba(2+), Sr(2+), Ca(2+)) Derived from Molecular Precursors and Doped with Eu(3+) Ions.

    Science.gov (United States)

    Drąg-Jarząbek, Anna; John, Łukasz; Petrus, Rafał; Kosińska-Klähn, Magdalena; Sobota, Piotr

    2016-03-24

    The effect of alkaline earth metal alkoxides on the protonation of zirconocene dichloride was investigated. This approach enabled the design of compounds with preset molecular structures for generating high-purity binary metal oxide perovskites MZrO3 (M=Ba(2+), Sr(2+), Ca(2+)). Single-source molecular precursors [Ba4 Zr2 (μ6 -O)(μ3 ,η(2)-OR)8 (OR)2(η(2) -HOR)2 (HOR)2 Cl4], [Sr4 Zr2 (μ6 -O)(μ3 ,η(2)-OR)8 (OR)2 (HOR)4 Cl4], [Ca4 Zr2 (μ6-O)(μ3 ,η(2)-OR)8 (OR)2 Cl4], and [Ca6 Zr2 (μ2 ,η(2)-OR)12 (μ-Cl)2 (η(2) -HOR)4 Cl6 ]⋅8 CH2 Cl2 were prepared via elimination of the cyclopentadienyl ring from Cp2 ZrCl2 as CpH in the presence of M(OR)2 and alcohol ROH (ROH=CH3OCH2 CH2OH) as a source of protons. The resulting complexes were characterized by elemental analysis, IR and NMR spectroscopy, and single-crystal X-ray diffraction. The compounds were then thermally decomposed to MCl2 /MZrO3 mixtures. Leaching of MCl2 from the raw powder with deionized water produced highly pure perovskite-like oxide particles of 40-80 nm in size. Luminescence studies on Eu(3+)-doped MZrO3 revealed that the perovskites are attractive host lattices for potential applications in display technology.

  17. Interaction of alkali and alkaline earth ions with Ochratoxin A

    Energy Technology Data Exchange (ETDEWEB)

    Poor, Miklos [Institute of Laboratory Medicine, University of Pecs, Pecs H-7624 (Hungary); Kunsagi-Mate, Sandor; Matisz, Gergely; Li, Yin; Czibulya, Zsuzsanna [Department of General and Physical Chemistry, University of Pecs, Pecs H-7624 (Hungary); Janos Szentagothai Research Center, Pecs H-7624 (Hungary); Peles-Lemli, Beata [Department of General and Physical Chemistry, University of Pecs, Pecs H-7624 (Hungary); Koszegi, Tamas, E-mail: koszegit@freemail.hu [Institute of Laboratory Medicine, University of Pecs, Pecs H-7624 (Hungary)

    2013-03-15

    The effect of alkali and alkaline earth ions on the chemical equilibrium of mono- and dianionic forms of the mycotoxin Ochratoxin A (OTA) and their bonding onto the surface of Bovine Serum Albumin (BSA) have been investigated by fluorescence spectroscopy and fluorescence polarization techniques. Our results show that alkali metal ions shift the chemical equilibrium towards formation of dianionic form of OTA. Furthermore, the alkaline earth ions can compete with BSA for binding to OTA when these ions are present in millimolar concentrations. Our data also highlight the possibility that the 'free' fraction of OTA (not bound onto the surface of albumin) or at least a part of it is present in cation-bound form in body fluids. These observations are supported by stability constants and quantum-chemical calculations. Among the studied alkaline metal ions magnesium showed the highest affinity towards OTA under physiological conditions. Further research is required to analyze the potential significance of Mg{sup 2+}-OTA complex in cellular uptake and/or elimination of the toxin in the human body. - Highlights: Black-Right-Pointing-Pointer Fluorescence spectroscopy reveals cation-Ochratoxin A (OTA) interactions. Black-Right-Pointing-Pointer Alkali ions shift the equilibrium of OTA to formation of a dianionic structure. Black-Right-Pointing-Pointer Alkaline earth ions directly bind to OTA in the order: Mg{sup 2+}, Ca{sup 2+}, Ba{sup 2+}. Black-Right-Pointing-Pointer Quantum chemical calculations and logK values support our experimental data.

  18. Proposal for Laser Cooling of Alkaline Earth Monoalkoxide Free Radicals

    Science.gov (United States)

    Baum, Louis; Kozyryev, Ivan; Matsuda, Kyle; Doyle, John M.

    2016-05-01

    Cold samples of polyatomic molecules will open new avenues in physics, chemistry, and quantum science. Non-diagonal Franck-Condon factors, technically challenging wavelengths, and the lack of strong electronic transitions inhibit direct laser cooling of nonlinear molecules. We identify a scheme for optical cycling in certain molecules with six or more atoms. Replacing hydrogen in alcohols with an alkaline earth metal (M) leads to alkaline earth monoalkoxide free radicals (MOR), which have favorable properties for laser cooling. M-O bond is very ionic, so the metal orbitals are slightly affected by the nature of R on the ligand. Diagonal Franck-Condon factors, laser accessible transitions, and a small hyperfine structure make MOR molecules suitable for laser cooling. We explore a scheme for optical cycling on the A - X transition of SrOCH3 . Molecules lost to dark vibrational states will be repumped on the B - X transition. Extension to larger species is possible through expansion of the R group since transitions involve the promotion of the metal-centered nonbonding valence electron. We will detail our estimations of the Franck-Condon factors, simulations of the cooling process and describe progress towards the Doppler cooling of MOR polyatomics.

  19. Structural diversity of alkaline-earth 2,5-thiophenedicarboxylates

    Science.gov (United States)

    Balendra; Ramanan, Arunachalam

    2017-03-01

    Exploration of the structural landscape of the system containing divalent alkaline-earth metal ion (Mg, Ca and Sr) with the rigid 2,5-thiophenedicarboxylic acid (TDC) under varying solvothermal condition (DMF, DMA and DEF) yielded five new crystals: [Mg(TDC) (DEF)2(H2O)1/2] (1), [Ca(TDC) (DMA)] (2), [Ca(TDC) (DMA) (H2O)] (3), [Sr(TDC) (DMA)] (4) and [Sr(TDC) (DMA) (H2O)] (5) and two known solids. Single crystal structures of all the solids are characteristic of extended coordination interaction between metal and carboxylate ions. While the smaller magnesium ion crystallized into a 2D coordination polymer, the larger calcium and strontium compounds resulted into the growth of 3D metal organic frameworks. All the solids show blue emission arising from intra ligand charge transfer.

  20. {sup 1}H and {sup 23}Na MAS NMR spectroscopy of cationic species in CO{sub 2} selective alkaline earth metal porous silicoaluminophosphates prepared via liquid and solid state ion exchange

    Energy Technology Data Exchange (ETDEWEB)

    Arevalo-Hidalgo, Ana G. [Department of Chemical Engineering, University of Puerto Rico-Mayagueez Campus, Mayagueez, PR 00681-9000 (Puerto Rico); Dugar, Sneha; Fu, Riqiang [National High Magnetic Field Laboratory, Florida State University, Tallahassee, FL 32310 (United States); Hernandez-Maldonado, Arturo J., E-mail: arturoj.hernandez@upr.edu [Department of Chemical Engineering, University of Puerto Rico-Mayagueez Campus, Mayagueez, PR 00681-9000 (Puerto Rico)

    2012-07-15

    The location of extraframework cations in Sr{sup 2+} and Ba{sup 2+} ion-exchanged SAPO-34 was estimated by means of {sup 1}H and {sup 23}Na MAS NMR spectroscopy and spectral deconvolution. Incorporation of the alkaline earth metal cations onto the SAPO framework was achieved via liquid state ion exchange, coupled partial detemplation/solid-state ion exchange, and combination of both techniques. MAS NMR revealed that the level of ion exchange was limited by the presence of protons and sodium cations near hexagonal prisms (site SI), which are relatively difficult to exchange with the alkaline earth metal due to steric and charge repulsion criteria. In addition, the presence of ammonium cations in the supercages facilitated the exchange of otherwise tenacious hydrogen as corroborated by unit cell compositional data as well as enhanced CO{sub 2} adsorption at low partial pressures. The extraframework ammonium species were produced from partial detemplation of the structure-directing agent employed for the SAPO-34 synthesis, tetraethylammonium. - Graphical abstract: MAS NMR was used to elucidate the position the cationic species in alkaline earth metal exchanged silicoaluminophosphates. These species played a significant role during the ion exchange process and, therefore, the materials ultimate CO{sub 2} adsorption performance. Highlights: Black-Right-Pointing-Pointer Location of extraframework Sr{sup 2+} or Ba{sup 2+} cations was estimated by means of {sup 1}H and {sup 23}Na MAS NMR. Black-Right-Pointing-Pointer Level of Sr{sup 2+} or Ba{sup 2+} ion exchange was limited by the presence of protons and sodium cations. Black-Right-Pointing-Pointer Presence of ammonium cations in the supercages facilitated the exchange. Black-Right-Pointing-Pointer Sr{sup 2+} and Ba{sup 2+} ion exchanged SAPOs are outstanding CO{sub 2} adsorbents.

  1. Synthesis and infrared spectra of alkaline earth metal carbonates formed by the reaction of metal salts with urea at high temperature

    Indian Academy of Sciences (India)

    S M Teleb; D El-Sayed Nassr; E M Nour

    2004-12-01

    The metal carbonate, MCO3 (M = Ca, Sr and Ba), was synthesized by a novel method of reacting aqueous solution of each of Ca2+, Sr2+ and Ba2+ salts with urea at high temperature, ∼ 80°C. The reaction products were characterized through elemental analysis and infrared spectra. The infrared spectra of the products are the same as those of the corresponding commercially obtained carbonates. A general reaction describing the formation of MCO3 is proposed.

  2. Effect of para-substituents on alkaline earth metal ion extraction by proton di-ionizable calix[4]arene-crown-6 ligands in cone, partial-cone and 1,3-alternate conformations.

    Science.gov (United States)

    Zhou, Hui; Liu, Dazhan; Gega, Jerzy; Surowiec, Kazimierz; Purkiss, David W; Bartsch, Richard A

    2007-01-21

    Two carboxylic acid or N-(X)sulfonyl carboxamide groups were incorporated into calix[4]arene-crown-6 compounds to afford di-ionizable ligands for use in divalent metal ion separations. Acidities of the N-(X)sulfonyl carboxamide groups were tuned by variation of the electron-withdrawing properties of X. Cone, partial-cone and 1,3-alternate conformations were obtained by different synthetic strategies and their structures verified by NMR spectroscopy. Competitive solvent extractions of alkaline earth metal cations from aqueous solutions into chloroform were performed and the results compared with those reported previously for di-ionizable p-tert-butylcalix[4]arene-crown-6 analogues to probe the influence of the para-substituent on the calix[4]arene scaffold on extraction selectivity and efficiency.

  3. Coordination Chemistry of Alkali and Alkaline-Earth Cations with Macrocyclic Ligands.

    Science.gov (United States)

    Dietrich, Bernard

    1985-01-01

    Discusses: (l) alkali and alkaline-earth cations in biology (considering naturally occurring lonophores, their X-ray structures, and physiochemical studies); (2) synthetic complexing agents for groups IA and IIA; and (3) ion transport across membranes (examining neutral macrobicyclic ligands as metal cation carriers, transport by anionic carriers,…

  4. Surface-treatment of Alkaline Earth Sulfides Based Phosphor

    Institute of Scientific and Technical Information of China (English)

    GUO Chong-feng; CHU Ben-li; XU Jian; SU Qiang

    2004-01-01

    A series of alkaline earth sulfides based phosphors Ca0.8Sr0.2S∶Eu2+, Tm3+ were covered with a layer of protective coating with alkaline earth fluorides by heating the mixture of phosphor and NH4HF2 at elevated temperatures. The coatings were characterized by means of XRD and SEM. The optical properties of the coated phosphors and the influences of the coating on their properties have been discussed extensively. The stabilities of the coated and uncoated phosphors have been compared.

  5. Binding to Redox-Inactive Alkali and Alkaline Earth Metal Ions Strongly Deactivates the C-H Bonds of Tertiary Amides toward Hydrogen Atom Transfer to Reactive Oxygen Centered Radicals.

    Science.gov (United States)

    Salamone, Michela; Carboni, Giulia; Mangiacapra, Livia; Bietti, Massimo

    2015-09-18

    The effect of alkali and alkaline earth metal ions on the reactions of the cumyloxyl radical (CumO(•)) with N,N-dimethylformamide (DMF) and N,N-dimethylacetamide (DMA) was studied by laser flash photolysis. In acetonitrile, a >2 order of magnitude decrease in the rate constant for hydrogen atom transfer (HAT) from the C-H bonds of these substrates (kH) was measured after addition of Li(+). This behavior was explained in terms of a strong interaction between Li(+) and the oxygen atom of both DMF and DMA that increases the extent of positive charge on the amide, leading to C-H bond deactivation toward HAT to the electrophilic radical CumO(•). Similar effects were observed after addition of Ca(2+), which was shown to strongly bind up to four equivalents of the amide substrates. With Mg(2+), weak C-H deactivation was observed for the first two substrate equivalents followed by stronger deactivation for two additional equivalents. No C-H deactivation was observed in DMSO after addition of Li(+) and Mg(2+). These results point toward the important role played by metal ion Lewis acidity and solvent Lewis basicity, indicating that C-H deactivation can be modulated by varying the nature of the metal cation and solvent and allowing for careful control over the HAT reactivity of amide substrates.

  6. Modelling the crystallisation of alkaline earth boroaluminosilicate glass ceramics

    DEFF Research Database (Denmark)

    Svenson, Mouritz Nolsøe; Agersted, Karsten; Holm, Paul Martin

    2014-01-01

    To investigate the potential use of a thermochemical software package (FactSage 6.2), in the design of alkaline earth boroaluminosilicate glass ceramics, experimental and modelled results on four glass ceramics were compared. Initially large discrepancies were found. These are described and related...... for the topology of multicomponent melts, before accurate prediction of phase relations within boron-containing glass ceramics can be obtained....

  7. Correlation-induced metal-insulator transitions in d{sup 0} magnetic superlattices based on alkaline-earth monoxides: Insights from ab initio calculations

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yi-Lin [Department of Applied Physics, Institute of Advanced Materials Physics, Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, Faculty of Science, Tianjin University, Tianjin 300072 (China); Dong, Shengjie [Department of Physics, Tianjin Normal University, Tianjin 300387 (China); Zhou, Baozeng [Department of Applied Physics, Institute of Advanced Materials Physics, Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, Faculty of Science, Tianjin University, Tianjin 300072 (China); Zhao, Hui [Department of Physics, Tianjin Normal University, Tianjin 300387 (China); Wu, Ping, E-mail: pingwu@tju.edu.cn [Department of Applied Physics, Institute of Advanced Materials Physics, Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, Faculty of Science, Tianjin University, Tianjin 300072 (China)

    2015-06-15

    Using first-principles density functional theory calculations, we have investigated the electronic structure and magnetic properties of four superlattices (MO){sub 1}/(MX){sub 1} (001) (M=Ca and Sr; X=N and C). Our results show that compared with standard GGA approach, the GGA plus effective U{sub eff} scheme can correct electronic structure and magnetic properties in some extent. With enhancing electronic correlation, for (CaO){sub 1}/(CaN){sub 1}, (SrO){sub 1}/(SrN){sub 1}, and (SrO){sub 1}/(SrC){sub 1}, the bands across Fermi level are divided into two parts and the shape of isotropic spherical spin atmosphere becomes anisotropic dumbbell-like with specific orientation, accompanying metal-insulator transitions. For (CaO){sub 1}/(CaC){sub 1}, the states just smearing with the Fermi level shift to lower energy region below Fermi level, indicating the transformation from a nearly half metal to an actual half metal occurs. The different behavior of (CaO){sub 1}/(CaC){sub 1} compared with three other compounds may be caused by the larger ionization energy of calcium than that of strontium and the smaller electronegativity of carbon than that of nitrogen. - Highlights: • The magnetic behaviors of four d{sup 0} superlattices are investigated. • The enhanced electronic correlation influences the magnetic properties. • (CaO){sub 1}/(CaC){sub 1} transforms from a nearly half metal to an actual half metal. • The other three compounds transform from half metals to magnetic insulators.

  8. Synthesis and alkaline earth metal cation extraction by proton di-ionizable p-tert-butylcalix[4]arene-crown-5 compounds in cone, partial-cone and 1,3-alternate conformations.

    Science.gov (United States)

    Zhou, Hui; Surowiec, Kazimierz; Purkiss, David W; Bartsch, Richard A

    2006-03-21

    Synthetic strategies for novel, proton di-ionizable p-tert-butylcalix[4]arene-crown-5 compounds in cone, partial-cone and 1,3-alternate conformations are reported. Selective linkage of the two diametrical phenolic oxygens in p-tert-butylcalix[4]arene with tetraethylene glycol ditosylate gave 1,3-bridged p-tert-butylcalix[4]arene-crown-5. The two remaining phenolic units were alkylated using NaH and KH as the bases to give the cone and partial-cone conformers, respectively. Preparation of the 1,3-alternate conformers utilized a different sequence in which O-alkylation was followed by crown ether ring formation. Structures of these new ligands were elucidated by (1)H and (13)C NMR spectroscopy. These proton-ionizable ligands were tested for their solvent extraction properties toward alkaline earth metal cations. Surprising differences in their extraction behaviors are noted compared to those reported previously for di-ionizable p-tert-butylcalix[4]arenecrown-6 analogues.

  9. A study on equilibrium and kinetics of ion exchange of alkaline earth metals using an inorganic cation exchanger - zirconium titanium phosphate

    Indian Academy of Sciences (India)

    Amin Jignasa; Thakkar Rakesh; Chudasama Uma

    2006-03-01

    An advanced inorganic cation exchange material of the class of tetravalent metal acid (TMA) salt, zirconium titanium phosphate (ZTP), has been synthesized by a modified sol-gel technique. ZTP has been characterized by elemental analysis (ICP-AES), thermal analysis (TGA), FTIR and X-ray diffraction studies. The Nernst-Planck equation has been used to study the forward and reverse ion exchange kinetics of Mg (II), Ca (II), Sr (II) and Ba (II) with H (I) at four different temperatures. The mechanism of exchange is particle diffusion, as confirmed by the linear (dimensionless time parameter) vs (time) plots. The exchange process is thus controlled by the diffusion within the exchanger particles for the systems studied herein. Further, various kinetic parameters like self-diffusion coefficient (0), energy of activation () and entropy of activation (*) have been evaluated under conditions favouring a particle diffusion-controlled mechanism.

  10. Pair natural orbital and canonical coupled cluster reaction enthalpies involving light to heavy alkali and alkaline earth metals: the importance of sub-valence correlation

    KAUST Repository

    Minenkov, Yury

    2017-03-07

    In this work, we tested canonical and domain based pair natural orbital coupled cluster methods (CCSD(T) and DLPNO-CCSD(T), respectively) for a set of 32 ligand exchange and association/dissociation reaction enthalpies involving ionic complexes of Li, Be, Na, Mg, Ca, Sr, Ba and Pb(ii). Two strategies were investigated: in the former, only valence electrons were included in the correlation treatment, giving rise to the computationally very efficient FC (frozen core) approach; in the latter, all non-ECP electrons were included in the correlation treatment, giving rise to the AE (all electron) approach. Apart from reactions involving Li and Be, the FC approach resulted in non-homogeneous performance. The FC approach leads to very small errors (<2 kcal mol-1) for some reactions of Na, Mg, Ca, Sr, Ba and Pb, while for a few reactions of Ca and Ba deviations up to 40 kcal mol-1 have been obtained. Large errors are both due to artificial mixing of the core (sub-valence) orbitals of metals and the valence orbitals of oxygen and halogens in the molecular orbitals treated as core, and due to neglecting core-core and core-valence correlation effects. These large errors are reduced to a few kcal mol-1 if the AE approach is used or the sub-valence orbitals of metals are included in the correlation treatment. On the technical side, the CCSD(T) and DLPNO-CCSD(T) results differ by a fraction of kcal mol-1, indicating the latter method as the perfect choice when the CPU efficiency is essential. For completely black-box applications, as requested in catalysis or thermochemical calculations, we recommend the DLPNO-CCSD(T) method with all electrons that are not covered by effective core potentials included in the correlation treatment and correlation-consistent polarized core valence basis sets of cc-pwCVQZ(-PP) quality.

  11. Helical ternary complexes of alkaline earth picrates with open-chain crown ether

    Institute of Scientific and Technical Information of China (English)

    刘伟生; 温永红; 刘雪原; 谭民裕

    2003-01-01

    Four solid complexes of alkaline earth picrates with N,N,N′,N′-tetraphenyl-3,6,9-tri- oxaundecanediamide (TTD), M (Pic)2TTD (1, M = Mg; 2, M = Ca; 3, M = Sr; 4, M = Ba), have been prepared and characterized by elemental analysis, conductivity measurement, IR spectra, 1H NMR spectra and TG-DTA techniques. Crystal structure of complex 3 shows that the Sr(Ⅱ) ion is 9-coordinated by five oxygen atoms from TTD and four oxygen atoms from two bidentate picrates, and the coordination polyhedron is distorted tricapped trigonal prism. TTD as a pentadentate ligand forms a right-handed helical coordination structure. The chelating helical chain has a relative fixed radius and then shows a high coordination selectivity to metal ion. The high selectivity of TTD to alkaline earth ions is explained elementarily from the special coordination structures.

  12. Study on rare earth/alkaline earth oxide-doped CeO2 solid electrolyte

    Institute of Scientific and Technical Information of China (English)

    YAN Kai; ZHEN Qiang; Song Xiwen

    2007-01-01

    Five types of rare earth/alkaline earth oxide-doped CeO2 superfine-powders were synthesized by a low-temperature combustion technique. The relevant solid electrolyte materials were also sintered by pressureless sintering at different temperatures. The results of X-ray diffraction and transmission electron microscopy showed that the grain size of the powders was approximately 20-30 nm, and rare earth/alkaline earth oxides were completely dissolved into ceria-based solid solution with fluorite structure. The electrical conductivities of the Sm2O3-CeO2 system were measured by the ac impedance technique in air at temperatures ranging from 513-900℃. The results indicated that the ionic conductivities of Sm0.20Ce0.8O1.875 solid electrolyte increase with increasing sintering temperature, and the relationship between the conductivities and measuring temperature obeys the Arrhenius equation. Then the Sm2O3-CeO2 material was further doped with other rare earth/alkaline earth oxide, and the conductivities improve with the effective index.

  13. Enhanced Magnetic Trap Loading for Alkaline-Earth Atoms

    Science.gov (United States)

    Reschovsky, Benjamin J.; Barker, Daniel S.; Pisenti, Neal C.; Campbell, Gretchen K.

    2016-05-01

    We report on a technique to improve the continuous loading of atomic strontium into a magnetic trap from a Magneto-Optical Trap (MOT). This is achieved by adding a depumping laser addressing the 3P1 level. For the 3P1 -->3S1 (688-nm) transition in strontium, the depumping laser increases atom number in the magnetic trap and subsequent cooling stages by up to 65 % for the bosonic isotopes and up to 30 % for the fermionic isotope. We optimize this trap loading strategy with respect to the 688-nm laser detuning, intensity, and beam size. To understand the results, we develop a one-dimensional rate equation model of the system, which is in good agreement with the data. We discuss the use of other transitions in strontium for accelerated trap loading and the application of the technique to other alkaline-earth-like atoms.

  14. IGCC sulfur compounds abatement with earth alkaline sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Ramon Alvarez-Rodriguez; Carmen Clemente-Jul [Universidad Politecnica de Madrid, Madrid (Spain). Escuela Tecnica Superior de Ingenieros de Minas

    2007-07-01

    In Integrated Gasification Combined Cycle (IGCC) process, in the reference plant built in Puertollano, Spain by Elcogas, a consortium formed by several utilities and engineering companies with a technology that is one of the most promising electricity generation options, both from the environmental and the efficiency point of view and that allows an efficient and environmentally friendly use of national coal, and also a refinery residue, petroleum coke, the high sulphur contents in coal and specially in petcoke, their presence in the feedstock, led to significant contents of gaseous sulphur compounds whose advanced removal has been the aim of this project. Different sorbents to reduce the presence of H{sub 2}S have been researched and between them the earth alkaline compounds, dolomite and calcite that react with H{sub 2}S to give calcium sulphide have been chosen due to their properties and low cost. The calcium sulphide is a reactive product because it reacts with water to regenerate the H{sub 2}S but it can be converted in calcium sulphate, inert product with diverse uses. This conversion to sulphate present some problems of possible lack of total conversion and different conditions to improve this conversion have been investigated. The tests have been carried out with dolomite and calcite and firstly the sulphuration of the same have been produced using a mixture of gases that simulates the IGCC gas and after their oxidation has been studied. The influence of the conditions of sulfurization and oxidation on the final conversion of calcium sulphide to sulphate as the presence of H{sub 2}O vapour, the variation in the composition of the gases, the temperature and the bed length have been evaluated. The solid products obtained have been characterized by X-ray diffraction and scanning electronic microscopy and chemical analysis to assess the evolution and progress of the reactions. 8 refs., 3 figs., 1 tab.

  15. Preparations of Pure Alkaline Earth Molybdate Phases from Single Molecular Precursors

    Institute of Scientific and Technical Information of China (English)

    JIANG Ya-qi; ZHAO Hong; FANG Zhi-min; WAN Hui-lin; XIONG Ming; ZHOU Zhao-hui

    2004-01-01

    The pure phases of alkaline earth molybdates MMoO4, where M=Mg, Ca, Sr or Ba, were synthesized via the calcination of the related citrato oxomolybdate complexes. The mixed metal oxides can be highly dispersed at the atomic level due to the existence of uniform citrato oxomolybdenum precursors in definite composition. The complexing effect helps to produce the fine-grained oxides with particle size in the ultrafine scale(<100 nm) at heat-treatment temperatures below 500 ℃. The structures of the precursor complexes and the finally heat-treated particles were studied by means of IR, XRD, DSC, DTA and TG techniques. The morphologies of the particles were observed by using the SEM technique. The average particle sizes were calculated to be in the range of 30-50 nm based on X-ray diffraction line-broadening and SEM images, indicating the poor conglomeration of crystallite at low temperatures.

  16. Coordination of alkaline earth metal ions in the inverted cucurbit[7]uril supramolecular assemblies formed in the presence of [ZnCl4]2- and [CdCl4]2-.

    Science.gov (United States)

    Li, Qing; Zhang, Yun-Qian; Zhu, Qian-Jiang; Xue, Sai-Feng; Tao, Zhu; Xiao, Xin

    2015-05-01

    A convenient method to isolate inverted cucurbit[7]uril (iQ[7]) from a mixture of water-soluble Q[n]s was established by eluting the soluble mixture of Q[n]s on a Dowex (H(+) form) column so that iQ[7] could be selected as a ligand for coordination and supramolecular assembly with alkaline earth cations (AE(2+)) in aqueous HCl solutions in the presence of [ZnCl(4)](2-) and [CdCl(4)](2-) anions as structure-directing agents. Single-crystal X-ray diffraction analysis revealed that both iQ[7]-AE(2+) -[ZnCl(4)](2-) -HCl and iQ[7]-AE(2+) -[CdCl(4)](2-) -HCl interaction systems yielded supramolecular assemblies, in which the [ZnCl(4)](2-) and [CdCl(4)](2-) anions presented a honeycomb effect, and this resulted in the formation of linear iQ[7]/AE(2+) coordination polymers through outer-surface interactions of Q[n]s.

  17. [Broad excitation band alkaline-earth silicate luminescent materials activated by rare earth and its applications].

    Science.gov (United States)

    Xia, Wei; Lei, Ming-Kai; Luo, Xi-Xian; Xiao, Zhi-Guo

    2008-01-01

    Series of novel broad excitation band phosphors M2 MgSis O7 : Eu, Dy(M = Ca, Sr) were prepared by a high temperature solid-state reaction method. The crystal structure of compound was characterized. And the effects of part substitution of alkaline-earth on crystal structure, photoluminescence spectra and luminescence properties were also investigated. It is found that the excitation band of silicate luminescent materials extend to visible region and they exhibit yellow, green and blue long after-glow luminescence after excited by ultraviolet or visible light. Ca MgSi O7 : Eu, Dy luminescent materials can be excited effectively under the 450-480 nm range and exhibit a strong emission at 536 nm, nicely combining with blue light emitted by InGaN chips to produce white light. This promises the silicate luminescent materials a potential yellow phosphor for white LED.

  18. Rare Earth Metals: Resourcefulness and Recovery

    Science.gov (United States)

    Wang, Shijie

    2013-10-01

    When we appreciate the digital revolution carried over from the twentieth century with mobile communication and the Internet, and when we enjoy our high-tech lifestyle filled with iDevices, hybrid cars, wind turbines, and solar cells in this new century, we should also appreciate that all of these advanced products depend on rare earth metals to function. Although there are only 136,000 tons of annual worldwide demand, (Cho, Rare Earth Metals, Will We Have Enough?)1 rare earth metals are becoming such hot commodities on international markets, due to not only to their increasing uses, including in most critical military hardware, but also to Chinese growth, which accounts for 95% of global rare earth metal production. Hence, the 2013 technical calendar topic, planned by the TMS/Hydrometallurgy and Electrometallurgy Committee, is particularly relevant, with four articles (including this commentary) contributed to the JOM October Issue discussing rare earth metals' resourcefulness and recovery.

  19. Alkaline earth-based coordination polymers derived from a cyclotriphosphazene-functionalized hexacarboxylate

    Science.gov (United States)

    Ling, Yajing; Bai, Dongjie; Feng, Yunlong; He, Yabing

    2016-10-01

    Combination of hexakis(4-carboxylatephenoxy)cyclotriphosphazene with alkaline earth ions of increasing ionic radii (Mg2+, Ca2+ and Ba2+) under different solvothermal conditions yielded three new coordination polymers, and their crystal structures were determined by single-crystal X-ray diffraction analysis. The magnesium compound displays a three dimensional (3D) network structure constructed from the deprotonated ligand and the secondary building block Mg(COO)4, which can be rationalized as a (4,6)-connected topological net with the Schläfli symbol of (44·62)3(49·66)2. The calcium compound consists of 1D infinite "Ca-O" inorganic chains connected by the deprotonated ligands to from a 3D framework. The barium compound exhibits a 3D framework in which 1D "Ba-O" inorganic chains are connected together by the deprotonated organic linkers. Due to the semi-rigid nature, the ligand adopts distinctly different conformations in the three compounds. The metal ions' influence exerted on the final structure of the resulting coordination polymers is also discussed. When the radii of alkaline earth ions increases descending down the group from Mg(II) to Ba(II), the coordination number becomes larger and more versatile: from 6 in the magnesium compound, to 6,7 and 10 in the calcium compound, and to 8 and 9 in the barium compound, thus substantially influencing the resulting final framework structures. Also, the photophysical properties were investigated systematically, revealing that the three compounds are photoluminscent in the solid state at room temperature. This work demonstrates that although the multiplicity of conformation in the hexacarboxylate ligand based on the inorganic scaffold cyclotriphosphazene makes it difficult to predict how this ligand will form extended network, but provides unique opportunities for the formation of diverse inorganic-organic hybrids exhibiting rich structural topologies.

  20. Dynamics of dipolar defects in rare earth-doped alkaline-earth fluoride crystals

    Science.gov (United States)

    Charnock, Forrest Taylor

    Alkaline-earth fluoride crystals such as SrF2 provide an excellent sample material for investigating the physics of point defects in crystal lattices. High quality crystals are easily grown, and they readily accept many dopant ions into the lattice, particularly rare earth ions. Rare earth dopant ions (typically trivalent) occupy substitutional sites in the lattice by replacing a Sr2+ ion. Due to the extra charge of the rare earth ion, charge compensation is often provided by an extra fluoride ion (F--) located in a nearby interstitial position. If located in the nearest-neighbor (nn) interstitial position, it forms a defect with C4n symmetry; if located in the next-nearest-neighbor (nnn) intersitial position, it forms a defect with C3n symmetry. Given sufficient thermal energy, this interstitial F ion can move to adjacent interstitial sites and hence reorient the defect. The rate w at which the ion moves from one interstitial site to another is well described by a simple Arrhenius expression: w=n0e-E/kT , where n0 is the attack frequency of the F-- and E is the activation energy. This motion can profoundly affect both the electronic polarizability of the material and the polarization of light emitted or absorbed by the rare earth ion. This thesis describes the normal mode motion of interstitial ions which may occupy either nn or nnn interstitial sites. Using electron paramagnetic resonance (EPR), I observed the relative populations of nn and nnn defects in SrF2 doped with Gd3+ as a function of temperature. These measurements show that dipolar reorientation of the nnn F occurs through the nn interstitial position. Not all interstitial F-- motion is thermally driven. Fluorescence depolarization measurements of SrF2:Pr3+ indicate that optically stimulating a Pr3+ may induce interstitial motion of a nn F--. Such motion was confirmed by showing that nn defects in SrF2:Pr3+ may be polarized at very low temperatures when the sample is illuminated with resonant light. I

  1. Spectroscopic characterization of manganese-doped alkaline earth lead zinc phosphate glasses

    Indian Academy of Sciences (India)

    S Sreehari Sastry; B Rupa Venkateswara Rao

    2015-04-01

    Alkaline earth lead zinc phosphate glasses doped with Mn(II) are characterized by spectroscopic techniques like X-ray diffraction (XRD), UV–visible, differential scanning calorimetry (DSC), electron paramagnetic resonance (EPR), Fourier transform infrared (FTIR) and Raman. Optical absorption spectrum exhibits four bands which are characteristic of Mn(II) in distorted octahedral site symmetry. The crystal field parameter Dq and Racah interelectronic-repulsion parameters and have been evaluated. All investigated samples exhibit EPR signals which are characteristic to the Mn2+ ions. The shapes of spectra are also changed with varying alkaline earth ions content. FTIR spectra show specific vibrations of phosphate units. The characteristic Raman bands of these glasses due to stretching and bending vibrations were identified and analysed by varying alkaline earth content. The intensity and frequency variations for the characteristic phosphate group vibrations have been correlated with the changes of the structural units present in these glasses. Depolymerization of the phosphate chains in all the glasses is observed with replacement of alkaline earth content by spectroscopic studies. This leads to a strong decrease of the average chain length and a small decrease of the average P–O–P bridging angle with replacement of alkaline earth content.

  2. Deselenization and detellurization of precious-metal ore concentrates by swelling oxidizing roasting and successive alkaline leaching

    Science.gov (United States)

    Zhang, Fu-yuan; Zheng, Ya-jie; Peng, Guo-min

    2017-02-01

    A new technique of swelling oxidizing roasting and alkaline leaching was proposed for deselenization and detellurization of precious-metal ore concentrates. Alkali-metal and alkaline-earth-metal chlorides and carbonates were preliminarily selected as swelling agents. The roasting removal rate and alkaline leaching rate of selenium and tellurium were investigated, and NaCl was selected as an appropriate swelling agent. Furthermore, the effects of various factors on the selenium gasification rate and leaching rate of selenium and tellurium were investigated. The results show that the selenium gasification rate reaches 88.41% after swelling oxidizing roasting for 2 h at 510°C using an NaCl dosage coefficient of 100 and a sulfuric acid dosage coefficient of 1.3; the amorphous elemental tellurium is completely transformed into TiO2. The roasted product is subjected to alkaline leaching using a 100 g/L NaOH solution, which results in a selenium leaching rate of 10.51%, a total selenium removal rate of 98.92%, and a tellurium leaching rate of 97.64%. In the alkaline leaching residue, the contents of selenium, tellurium, gold, platinum, and palladium are 0.7825%, 5.492%, 8.333%, 0.2587%, and 1.113%, respectively; the precious metals are enriched approximately sixfold.

  3. Alkali-metal/alkaline-earth-metal fluorine beryllium borate NaSr{sub 3}Be{sub 3}B{sub 3}O{sub 9}F{sub 4} with large nonlinear optical properties in the deep-ultraviolet region

    Energy Technology Data Exchange (ETDEWEB)

    Reshak, A. H., E-mail: maalidph@yahoo.com [New Technologies—Research Centre, University of West Bohemia, Univerzitni 8, 306 14 Pilsen (Czech Republic); Center of Excellence Geopolymer and Green Technology, School of Material Engineering, University Malaysia Perlis, 01007 Kangar, Perlis (Malaysia); Huang, Hongwei [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Kamarudin, H. [Center of Excellence Geopolymer and Green Technology, School of Material Engineering, University Malaysia Perlis, 01007 Kangar, Perlis (Malaysia); Auluck, S. [Council of Scientific and Industrial Research—National Physical Laboratory, Dr. K S Krishnan Marg, New Delhi 110012, India and Physics Department, Indian Institute of Technology - Delhi, Hauz Khas, New Delhi 110016 (India)

    2015-02-28

    The linear optical response and second harmonic generation (SHG) in alkali-metal/alkaline-earth-metal fluorine beryllium borate NaSr{sub 3}Be{sub 3}B{sub 3}O{sub 9}F{sub 4} are investigated by means of density functional theory. Calculations are performed using four types of exchange correlations: Ceperley-Alder local density approximation, Perdew Burke and Ernzerhof general gradient approximation, Engel-Vosko generalized gradient approximation, and the recently modified Becke-Johnson potential (mBJ). The mBJ approach brings the calculated band gap (7.20 eV) in excellent agreement with the experimental one (7.28 eV). The calculated values of the uniaxial anisotropy δε=−0.076 and the birefringence Δn(0)=0.052 indicate considerable anisotropy in the linear optical properties, which makes it favorable for the second harmonic generation. The dominant component of the second harmonic generation is χ{sub 111}{sup (2)}(ω). The value of |χ{sub 111}{sup (2)}(ω)| is about 1.2 pm/V at λ = 1064 nm in agreement with previous calculations. To analyze the origin of the high SHG of NaSr{sub 3}Be{sub 3}B{sub 3}O{sub 9}F{sub 4} single crystals, we have correlated the features of |χ{sub 111}{sup (2)}(ω)| spectra with the features of ε{sub 2}(ω) spectra as a function of ω/2 and ω. From the calculated dominant component |χ{sub 111}{sup (2)}(ω)|, we find that the microscopic first hyperpolarizability, β{sub 111}, the vector components along the dipole moment direction is 0.5 × 10{sup −30} esu at static limit and 0.6 × 10{sup −30} esu at λ = 1064 nm.

  4. Desorption of acetone from alkaline-earth exchanged Y zeolite after propane selective oxidation

    NARCIS (Netherlands)

    Xu, Jiang; Mojet, B.L.; Ommen, van J.G.; Lefferts, L.

    2004-01-01

    The desorption of products from a series of alkaline-earth exchanged Y zeolites after room-temperature propane selective oxidation was investigated by in situ infrared and mass spectroscopy. The intermediate product, isopropylhydroperoxide (IHP), did not desorb during temperature-programmed-desorpti

  5. FORMATION (DECOMPOSITION) ENTHALPY CALCULATIONS FOR CRYSTAL LATTICES OF ALKALINE-EARTH FLUORIDES

    OpenAIRE

    Gruba, O.; Germanyuk, N.; Ryabukhin, A.

    2015-01-01

    A series of calculations of structural and thermochemical properties has been carried out for the alkaline-earth fluorides. The calculations have been carried out using the modified model of effective ionic radii and the model of enthalpy calculation for the crystal lattice. The results of the calculations are in accordance with the known experimental data within confidence intervals.

  6. Propane selective oxidation on alkaline earth exchanged zeolite Y: room temperature in situ IR study

    NARCIS (Netherlands)

    Xu, Jiang; Mojet, Barbara L.; Ommen, van Jan G.; Lefferts, Leon

    2003-01-01

    The effect of zeolite Y ion-exchanged with a series of alkaline-earth cations on selective propane oxidation at room temperature was studied with in situ infrared spectroscopy. Isopropylhydroperoxide was observed as a reaction intermediate and can be decomposed into acetone and water. Contrary to pr

  7. Conformation Switching in Gas-Phase Complexes of Histidine with Alkaline Earth Ions

    NARCIS (Netherlands)

    Dunbar, R. C.; Hopkinson, A. C.; Oomens, J.; Siu, C. K.; Siu, K. W. M.; Steill, J. D.; Verkerk, U. H.; Zhao, J. F.

    2009-01-01

    Infrared multiple photon dissociation spectroscopy of gas-phase doubly charged alkaline earth complexes of histidine reveals a transition from dominance of the zwitterion (salt bridge, SB) conformation with Ba2+ to substantial presence of the canonical (charge-solvated, CS) conformation with Ca2+. T

  8. Carbonatite and alkaline intrusion-related rare earth element deposits–A deposit model

    Science.gov (United States)

    Verplanck, Philip L.; Van Gosen, Bradley S.

    2011-01-01

    The rare earth elements are not as rare in nature as their name implies, but economic deposits with these elements are not common and few deposits have been large producers. In the past 25 years, demand for rare earth elements has increased dramatically because of their wide and diverse use in high-technology applications. Yet, presently the global production and supply of rare earth elements come from only a few sources. China produces more than 95 percent of the world's supply of rare earth elements. Because of China's decision to restrict exports of these elements, the price of rare earth elements has increased and industrial countries are concerned about supply shortages. As a result, understanding the distribution and origin of rare earth elements deposits, and identifying and quantifying our nation's rare earth elements resources have become priorities. Carbonatite and alkaline intrusive complexes, as well as their weathering products, are the primary sources of rare earth elements. The general mineral deposit model summarized here is part of an effort by the U.S. Geological Survey's Mineral Resources Program to update existing models and develop new descriptive mineral deposit models to supplement previously published models for use in mineral-resource and mineral-environmental assessments. Carbonatite and alkaline intrusion-related REE deposits are discussed together because of their spatial association, common enrichment in incompatible elements, and similarities in genesis. A wide variety of commodities have been exploited from carbonatites and alkaline igneous rocks, such as rare earth elements, niobium, phosphate, titanium, vermiculite, barite, fluorite, copper, calcite, and zirconium. Other enrichments include manganese, strontium, tantalum, thorium, vanadium, and uranium.

  9. Alkaline earth oxide nanoparticles as destructive absorbents for environmental toxins

    Energy Technology Data Exchange (ETDEWEB)

    Moscovici, J.; Latreche, K. [Univ. Paris XII, Groupe de Physique des Milieux Denses, Creteil (France); Michalowicz, A. [Univ. Paris Sud, LURE, Orsay (France); Decker, S.; Lagadic, I.; Klabunde, K. [Kansas State Univ., Chemistry Dept., Manhattan, Kansas (United States)

    1999-11-01

    Sr and Ca oxide nanoparticles are very reactive materials used to mitigate atmospheric pollution and to sequester polluting molecules. We have studied the structure of SrO nanoparticles, using Sr K-edge and Fe K-edge XAFS, that were prepared with various reactivities, with or without a Fe{sub 2}O{sub 3} coating, and before and after reaction with CCl{sub 4} or SO2. For CCl4, the polluting fraction of the reagent is totally absorbed in the bulk particle. For SO{sub 2}, the results show a total reaction for the Aerogel Preparation (AP) compound. For the coated particles before reaction, the iron oxide has a very disordered structure, and it is mixed with small metallic iron clusters for Conventional Preparation (CP) compounds. (au) 4 refs.

  10. Alkali metal and alkali earth metal gadolinium halide scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  11. Enthalpies of formation and lattice enthalpies of alkaline metal acetates

    Energy Technology Data Exchange (ETDEWEB)

    Aleixo, Ana I. [Departamento de Quimica e Bioquimica, Faculdade de Ciencias, Universidade de Lisboa, 1749-016 Lisbon (Portugal); Oliveira, Pedro H. [Centro de Quimica Estrutural, Complexo Interdisciplinar, Instituto Superior Tecnico, 1049-001 Lisbon (Portugal); Diogo, Herminio P. [Centro de Quimica Estrutural, Complexo Interdisciplinar, Instituto Superior Tecnico, 1049-001 Lisbon (Portugal); Minas da Piedade, Manuel E. [Departamento de Quimica e Bioquimica, Faculdade de Ciencias, Universidade de Lisboa, 1749-016 Lisbon (Portugal)]. E-mail: memp@fc.ul.pt

    2005-04-15

    The standard (p{sup o}=0.1MPa) molar enthalpies of formation in the crystalline state of the alkaline metal acetates CH{sub 3}COOM (M=Li, Na, K, Rb, Cs), at T=298.15K, were determined by reaction-solution calorimetry as: {delta}{sub f}H{sub m}{sup o}(CH{sub 3}COOLi,cr)=-(741.40+/-0.95)kJmol{sup -1}, {delta}{sub f}H{sub m}{sup o}(CH{sub 3}COONa,cr)=-(711.01+/-0.51)kJmol{sup -1}, {delta}{sub f}H{sub m}{sup o}(CH{sub 3}COOK,cr)=-(722.36+/-0.49)kJmol{sup -1}, {delta}{sub f}H{sub m}{sup o}(CH{sub 3}COORb,cr)=-(722.31+/-1.09)kJmol{sup -1}, {delta}{sub f}H{sub m}{sup o}(CH{sub 3}COOCs,cr)=-(726.10+/-1.07)kJmol{sup -1}. These results, taken together with the enthalpies of formation of the haloacetates XCH{sub 2}COOM (M=Li, Na; X=Cl, Br, I) and chloropropionates ClCH(CH{sub 3})COOM (M=Li, Na) re-evaluated from literature data were used to derive a consistent set of lattice energies, and discuss some general trends of the structure-energetics relationship for the CH{sub 3}COOM, XCH{sub 2}COOM, and ClCH(CH{sub 3})COOM compounds, based on the Kapustinskii approximation. It was found that the lattice energies of the haloacetates are essentially independent of the halogen and ca. 17-25kJmol{sup -1} smaller than those of the corresponding acetates. In addition, no significant difference between the lattice enthalpy values of the haloacetates and chloropropionates was observed. Finally, linear correlations of very similar slope were obtained by plotting the M-O bond distances derived from the Kapustinskii equation against the published experimental M-O bond distances for alkaline metal acetates and alkoxides. The analysis of these relations suggests that the metal-oxygen bond distances for the lithium, potassium, and rubidium acetates, whose molecular structures in the solid state have not been determined, can be estimated as 214, 288, and 304pm, respectively.

  12. Synthesis and acid digestion of biomorphic ceramics: determination of alkaline and alkaline earth ions.

    Science.gov (United States)

    Bosch Ojeda, Catalina; Sánchez Rojas, Fuensanta; Cano Pavón, José Manuel

    2007-09-01

    Ceramic and glass are some of the more recent engineering materials and those that are most resistant to environmental conditions. They belong to advanced materials in that they are being developed for the aerospace and electronics industries. In the last decade, a new class of ceramic materials has been the focus of particular attention. The materials were produced with natural, renewable resources (wood or wood-based products). In this work, we have synthesised a new biomorphic ceramic material from oak wood and Si infiltration. After the material characterization, we have optimized the dissolution of the sample by acid attack in an oven under microwave irradiation. Experimental designs were used as a multivariate strategy for the evaluation of the effects of varying several variables at the same time. The optimization was performed in two steps using factorial design for preliminary evaluation and a Draper-Lin design for determination of the critical experimental conditions. Five variables (time, power, volume of HNO3, volume H2SO4 and volume of HF) were considered as factors and as a response the concentration of different metal ions in the optimization process. Interactions between analytical factors and their optimal levels were investigated using a Draper-Lin design.

  13. Environmental effects on fatigue of alkaline earth aluminosilicate glass with varying fictive temperature

    DEFF Research Database (Denmark)

    Striepe, Simon; Deubener, Joachim; Smedskjær, Morten Mattrup;

    2013-01-01

    The influence of relative humidity on microhardness, stress intensity, crack resistance, and sub-critical crack growth of an alkaline earth aluminosilicate glass has been studied by Vickers indentation. Quenched and annealed glasses with a wide range of fictive temperatures (ΔTf ≈ 130 K) are comp......The influence of relative humidity on microhardness, stress intensity, crack resistance, and sub-critical crack growth of an alkaline earth aluminosilicate glass has been studied by Vickers indentation. Quenched and annealed glasses with a wide range of fictive temperatures (ΔTf ≈ 130 K......) are compared in order to determine the influence of the thermal history on these properties. Vickers hardness is found to be essentially unaffected by the environmental conditions, while the stress intensity factor (fracture toughness) and the crack resistance decrease significantly with increasing humidity...

  14. Properties of the triplet metastable states of the alkaline-earth atoms

    CERN Document Server

    Mitroy, J

    2004-01-01

    The static and dynamic properties of the alkaline-earth atoms in their metastable state are computed in a configuration interaction approach with a semi-empirical model potential for the core. Among the properties determined are the scalar and tensor polarizabilities, the quadrupole moment, some of the oscillator strengths and the dispersion coefficients of the van der Waals interaction. A simple method for including the effect of the core on the dispersion parameters is described.

  15. Spectroscopic studies of copper doped alkaline earth lead zinc phosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, S. Sreehari, E-mail: sreeharisastry@yahoo.com [Department of Physics, Acharya Nagarjuna University, Nagarjunanagar 522510 (India); Rao, B. Rupa Venkateswara [Department of Physics, Acharya Nagarjuna University, Nagarjunanagar 522510 (India); Department of Physics, V.R. Siddhartha Engineering College, Vijayawada 52007 (India)

    2014-02-01

    In this paper spectroscopic investigation of Cu{sup 2+} doped alkaline earth lead zinc phosphate glasses was done through the spectroscopic techniques like X-ray diffraction, Ultra Violet (UV) absorption Spectroscopy, Electron Paramagnetic Resonance (EPR – X band), Fourier Transform Infra Red (FTIR) and Raman Spectroscopy. Alkaline earth lead zinc phosphate glasses containing 0.1% copper oxide (CuO) were prepared by the melt quenching technique. Spectroscopic studies indicated that there is a greater possibility for the copper ions to exist in Cu{sup 2+} state in these glasses. The optical absorption spectra indicated that the absorption peak of Cu{sup 2+} is a function of composition. The maxima absorption peak was reported at 862 nm for strontium lead zinc phosphate glass. Bonding parameters were calculated for the optical and EPR data. All these spectral results indicated clearly that there are certain structural changes in the present glass system with different alkaline earth contents. The IR and Raman spectra noticed the breaking of the P–O–P bonds and creating more number of new P–O–Cu bonds.

  16. Spectroscopic studies of copper doped alkaline earth lead zinc phosphate glasses

    Science.gov (United States)

    Sastry, S. Sreehari; Rao, B. Rupa Venkateswara

    2014-02-01

    In this paper spectroscopic investigation of Cu2+ doped alkaline earth lead zinc phosphate glasses was done through the spectroscopic techniques like X-ray diffraction, Ultra Violet (UV) absorption Spectroscopy, Electron Paramagnetic Resonance (EPR - X band), Fourier Transform Infra Red (FTIR) and Raman Spectroscopy. Alkaline earth lead zinc phosphate glasses containing 0.1% copper oxide (CuO) were prepared by the melt quenching technique. Spectroscopic studies indicated that there is a greater possibility for the copper ions to exist in Cu2+ state in these glasses. The optical absorption spectra indicated that the absorption peak of Cu2+ is a function of composition. The maxima absorption peak was reported at 862 nm for strontium lead zinc phosphate glass. Bonding parameters were calculated for the optical and EPR data. All these spectral results indicated clearly that there are certain structural changes in the present glass system with different alkaline earth contents. The IR and Raman spectra noticed the breaking of the P-O-P bonds and creating more number of new P-O-Cu bonds.

  17. Effects of Rare Earth and Alkaline Earth on Spheroidizing of Eutectic Carbides in Low Tungsten White Cast Iron

    Institute of Scientific and Technical Information of China (English)

    Fu Hanguang; Zou Dening

    2004-01-01

    Tungsten Alloy White Cast Iron(TAWCI) has great brittleness and narrow application scope. The influences of Rare earth element(Ce) and alkaline earth elements ( K, Na) on the microstructures and performances of TAWCI were researched, and the idea estimating spheroidizing effect of carbides using Circular Degree (C. D) were put forward. The result shows that eutectics carbide tums into sphericity from network after modification, and carbide is refined and uniformly distributed and the C. D of eutectic carbide increases. The mechanism of carbide spheroidizing was analyzed. The impact toughness and wear resistance of TAWCI obviously improve with the rise of C. D of carbides.The service life of modified TAWCI roll is 35 % higher than that of high chromium cast iron roll, and its production cost is reduced by 25 %.

  18. Structural criteria for the rational design of selective ligands. Extension of the MM3 force field to aliphatic ether complexes of the alkali and alkaline earth cations

    Energy Technology Data Exchange (ETDEWEB)

    Hay, B.P.; Rustad, J.R. (Pacific Northwest Lab., Richland, WA (United States))

    1994-07-13

    Structural requirements for strain-free metal ion complexation by an aliphatic ether group are investigated through the use of both ab initio molecular orbital and molecular mechanics calculations. Hartree-Fock calculations on simple models, M-O(Me)[sub 2] and M-O(Me)(Et), reveal a preference for trigonal planar geometry when aliphatic ether oxygens are coordinated to alkali and alkaline earth cations. This preference is found to be strongest in small, high-valent cations and weakest in large, low-valent cations. Results from the Hartree-Fock calculations are used to extend the MM3 force field for calculation on aliphatic ether complexes with the alkali (Li to Cs) and alkaline earth (Mg to Ba) cations. The resulting molecular model (i) reproduces the experimental crystal structures of 51 different complexes of multidentate ethers with alkali and alkaline earth cations, (ii) explains experimental trends in the structure of five-membered chelate rings of aliphatic ethers, (iii) reveals a fundamental difference between the metal ion size selectivity of five-membered chelate rings of ethers versus that of amines, and (iv) rationalizes trends in the stability of four potassium complexes with the diasteriomers of dicyclohexyl-18-crown-6. 40 refs., 9 figs., 5 tabs.

  19. Creation of trapped electrons and holes in alkaline-earth fluoride crystals doped by rare-earth ions

    Science.gov (United States)

    Radzhabov, E.

    2002-06-01

    Defects in Ce 3+- and Eu 2+-doped alkaline-earth fluorides, created by vacuum ultraviolet (VUV) photons with energy lower than that of the band gap, were investigated by various methods: thermostimulated luminescence, photostimulated luminescence and optical absorption. The CaF 2:Eu 2+ thermoluminescence curves in the range of 60-330 K due to various types of trapped holes were the same after VUV illumination as after X-ray irradiation. Thermoluminescence curves of Ce 3+-doped alkaline-earth fluorides created by VUV illumination or X-ray irradiation were generally similar. However, Vk thermoluminescence peaks were absent in VUV-illuminated CaF 2:Ce 3+ and SrF 2:Ce 3+ crystals. Creation of Ce 2+ characteristic bands was observed in photostimulated luminescence spectra as well as in optical absorption spectra of vacuum ultraviolet-illuminated or X-ray-irradiated Ce 3+-doped crystals. The proposed mechanism of creation of trapped hole and trapped electron defects by vacuum ultraviolet illumination involves charge transfer-type transitions, in which the electron transfers from valence band to an impurity level, lying in the band gap. Comparison of all involved energies of transitions in the crystals investigated shows that the sum of all transition energies is less than that of the band gap by 1-3 eV. This energy difference can be considered as the energy of lattice relaxation around created Ce 2+ or Eu + ions.

  20. STARK STRUCTURE OF THE RYDBERG STATES OF ALKALINE-EARTH ATOMS

    Institute of Scientific and Technical Information of China (English)

    郅妙婵; 戴长建; 李士本

    2001-01-01

    The Stark effects of the Rydberg states in the alkaline-earth atoms are studied theoretically. Using a method similar to the treatment of alkali atoms, the properties of the Stark states of Mg, Ca, Sr and Ba atoms in the regions far away from the perturbers are investigated. The Stark maps for Mg (n=16, M=0), Ca (n=10, M=0), Sr (n=12,M=0) and Ba (n=13, |M|=0,1) are presented. Topics such as the general methods of calculation, the treatment of fine structure, and the structure of level anti-crossings are discussed. The comparison between the theoretical and experimental Stark maps is satisfactory.

  1. Eocene seasonality and seawater alkaline earth reconstruction using shallow-dwelling large benthic foraminifera

    Science.gov (United States)

    Evans, David; Müller, Wolfgang; Oron, Shai; Renema, Willem

    2013-11-01

    Intra-test variability in Mg/Ca and other (trace) elements within large benthic foraminifera (LBF) of the family Nummulitidae have been investigated using laser-ablation inductively-coupled plasma mass spectrometry (LA-ICPMS). These foraminifera have a longevity and size facilitating seasonal proxy retrieval and a depth distribution similar to 'surface-dwelling' planktic foraminifera. Coupled with their abundance in climatically important periods such as the Paleogene, this means that this family of foraminifera are an important but under-utilised source of palaeoclimatic information. We have calibrated the relationship between Mg/Ca and temperature in modern Operculina ammonoides and observe a ˜2% increase in Mg/Ca °C-1. O. ammonoides is the nearest living relative of the abundant Eocene genus Nummulites, enabling us to reconstruct mid-Eocene tropical sea surface temperature seasonality by applying our calibration to fossil Nummulites djokdjokartae from Java. Our results indicate a 5-6 °C annual temperature range, implying greater than modern seasonality in the mid-Eocene (Bartonian). This is consistent with seasonal surface ocean cooling facilitated by enhanced Eocene tropical cyclone-induced upper ocean mixing, as suggested by recent modelling results. Analyses of fossil N. djokdjokartae and Operculina sp. from the same stratigraphic interval demonstrate that environmental controls on proxy distribution coefficients are the same for these two genera, within error. Using previously published test-seawater alkaline earth metal distribution coefficients derived from an LBF of the same family (Raitzsch et al., 2010) and inorganic calcite, with appropriate correction systematics for secular Mg/Casw variation (Evans and Müller, 2012), we use our fossil data to produce a more accurate foraminifera-based Mg/Casw reconstruction and an estimate of seawater Sr/Ca. We demonstrate that mid-Eocene Mg/Casw was ≲2 molmol, which is in contrast to the model most

  2. Physicochemical study of alkaline earth metal and magnesium maleates

    Energy Technology Data Exchange (ETDEWEB)

    Koblova, O.E.; Vdovina, L.M.; Frolova, L.A. (Saratovskij Gosudarstvennyj Univ. (USSR); Saratovskij Gosudarstvennyj Pedagogicheskij Inst. (USSR))

    1982-01-01

    Magnesium, calcium, strontium and barium maleates are synthesized. Their thermal stability in the atmosphere of air and argon is studied. It is shown that the dehydration of initial salts proceeds in the temperature range of 100-300 deg C. The decomposition of anhydrous salts takes place in the temperature range of 380-600 deg C. The values of the effective activation energy are determined.

  3. Destructive Adsorption of Carbon Tetrachloride on Alkaline Earth Metal Oxides

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Mestl, Gerhard; Rosynek, Michael P.; Krawietz, Thomas R.; Haw, James F.; Lunsford, Jack H.

    2001-01-01

    The destructive adsorption of CCl4 on MgO, CaO, SrO, and BaO has been studied as a function of the reaction temperature and the amount of CCl4 injected. The reaction was followed using in situ Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and 13 C mag

  4. Health Effects of Alkaline Diet and Water, Reduction of Digestive-tract Bacterial Load, and Earthing.

    Science.gov (United States)

    Mousa, Haider Abdul-Lateef

    2016-04-01

    In the article, the author discusses the issue of chronic, low-grade acidosis that is thought to be brought about primarily by 2 factors: (1) advancing age, with a consequent decline in renal function; and (2) diet. An acid-forming diet can induce low-grade metabolic acidosis, which causes very small decreases in blood pH and plasma bicarbonate (HCO3-) that remain within the range considered to be normal. However, if the duration of the acidosis is prolonged or chronically present, even a low degree of acidosis can become significant. This article reviews supporting evidence in the literature that has shown that consumption of abundant alkaline-forming foods can result in improvement in bone mineral density (BMD) and muscle mass, protection from chronic illnesses, reduced tumor-cell invasion and metastasis, and effective excretion of toxins from the body. In addition, a large number of studies showing the benefits of alkaline water (mineral water) have revealed that people consuming water with a high level of total dissolved solids (TDS) (ie, with a high mineral content) have shown a lower incidence of coronary heart disease (CHD), cardiovascular disease (CVD), and cancer and lower total mortality rates. Consumption of alkaline water also may prevent osteoporosis and protect pancreatic beta cells with its antioxidant effects. In addition, this article discusses the literature that shows that reducing digestive-tract bacterial load can play an important role in increasing blood alkalinity toward the normal upper limit. That change occurs through good oral hygiene, flossing of teeth, perfect chewing of food, and bowel evacuation as soon as possible. Finally, the author reviews the literature that shows that earthing (ie, the direct contact of the human body with the earth) can supply a current of plentiful electrons. Earthing has been shown to reduce acute and chronic inflammation, blood glucose in patients with diabetes, red blood cell (RBC) aggregation, and blood

  5. Nanocrystalline Powders of Alkaline-Earth Phosphates as Precursors for Bioceramics

    Directory of Open Access Journals (Sweden)

    Parhi Purnendu

    2006-01-01

    Full Text Available Bone is a nanocomposite made of calcium phosphates and collagen. Collagen has a typical fibrous structure, with diameter ranging from 100 nm to 2 µm. It is suggested that calcium hydroxyapatite, Ca10(PO46(OH2 in the size range 5-50 nm embedded in the collagen framework provides mechanical strength to bone. Among calcium phosphates, apatites are found to be the most suitable for bone regeneration due to its biocompatibility. A contemporary theme is to prepare nanocrystallites of alkaline-earth phosphates that can be employed as precursors for making novel bioceramics. In this paper, we present our attempts to prepare nano-sized particles of alkaline-earth hydroxyapatites, A10(PO46(OH2 where A= Ca, Sr and Ba through a metathetical route. Our work involved the use of same reactants treated under different reaction conditions. While hydrothermal route yielded well-crystalline nanorods, microwave resulted in agglomerated hydroxyapatites and reverse micellear route gave low crystalline apatites with less agglomeration.

  6. Temperature-induced collapse of alkaline Earth cation-polyacrylate anion complexes.

    Science.gov (United States)

    Lages, Sebastian; Schweins, Ralf; Huber, Klaus

    2007-09-06

    Polyacrylate anions are used to inhibit CaCO3 precipitation and may be a promising additive to control formation of inorganic nanoparticles. The origin of this applicability lies in specific interactions between the alkaline earth cations and the carboxylate functions along the polyacrylate chains. In the absence of CO32- anions, these interactions eventually cause precipitation of polyelectrolytes. Extended investigation of dilute sodium polyacrylate solutions approaching this precipitation threshold revealed a dramatic shrinking of the PA coil dimensions once the threshold is reached (Eur. Phys. J. E 2001, 5, 117). Recent isothermal calorimetric titration experiments by Antonietti et al. (Macromolecules 2004, 37, 3444) indicated that the driving force of this precipitation is entropic in nature. In the present work, we investigated the impact of temperature on the structural changes of dissolved polyacrylate chains decorated with alkaline earth cations. To this end, large polyacrylate chains were brought close to the precipitation threshold by the addition of distinct amounts of Ca2+ or Sr2+ cations. The resulting structural intermediates were then subjected to temperature variations in the range of 15 degrees C polyacrylate coils were recorded by means of light and neutron scattering. As a major result, we could unambiguously demonstrate that the coils can reversibly be collapsed and extended by increasing and decreasing the temperature, respectively.

  7. Maternal exposure to alkali, alkali earth, transition and other metals: Concentrations and predictors of exposure.

    Science.gov (United States)

    Hinwood, A L; Stasinska, A; Callan, A C; Heyworth, J; Ramalingam, M; Boyce, M; McCafferty, P; Odland, J Ø

    2015-09-01

    Most studies of metals exposure focus on the heavy metals. There are many other metals (the transition, alkali and alkaline earth metals in particular) in common use in electronics, defense industries, emitted via combustion and which are naturally present in the environment, that have received limited attention in terms of human exposure. We analysed samples of whole blood (172), urine (173) and drinking water (172) for antimony, beryllium, bismuth, cesium, gallium, rubidium, silver, strontium, thallium, thorium and vanadium using ICPMS. In general most metals concentrations were low and below the analytical limit of detection with some high concentrations observed. Few factors examined in regression models were shown to influence biological metals concentrations and explained little of the variation. Further study is required to establish the source of metals exposures at the high end of the ranges of concentrations measured and the potential for any adverse health impacts in children.

  8. A new N-hydroxyethyliminodiacetic acid modified core-shell silica phase for chelation ion chromatography of alkaline earth, transition and rare earth elements.

    Science.gov (United States)

    McGillicuddy, Nicola; Nesterenko, Ekaterina P; Nesterenko, Pavel N; Stack, Elaine M; Omamogho, Jesse O; Glennon, Jeremy D; Paull, Brett

    2013-12-20

    Bare core-shell silica (1.7μm) has been modified with iminodiacetic acid functional groups via standard silane chemistry, forming a new N-hydroxyethyliminodiacetic acid (HEIDA) functionalised core-shell stationary phase. The column was applied in high-performance chelation ion chromatography and evaluated for the retention of alkaline earth, transition and heavy metal cations. The influence of nitric acid eluent concentration, addition of complexing agent dipicolinic acid, eluent pH and column temperature on the column performance was investigated. The efficiencies obtained for transition and heavy metal cations (and resultant separations) were comparable or better than those previously obtained for alternative fully porous silica based chelation stationary phases, and a similarly modified monolithic silica column, ranging from ∼15 to 56μm HETP. Increasing the ionic strength of the eluent with the addition of KNO3 (0.75M) and increasing the column temperature (70°C) facilitated the isocratic separation of a mixture of 14 lanthanides and yttrium in under 12min, with HETP averaging 18μm (7μm for Ce(III)).

  9. Some Rare Earth Metallic Organohydrides with Biindenyl as the Ligand

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Introduction It is well known that organometallic hydrides of rare earth metals are the catalysts and reducing reagents for the catalysis polymerization of alkenes and the catalysis hydrogenation of alkenoalkynes. There are four methods for the syntheses of organometallic hydrides of rare earth metals: (1) the thermal atomization of metals, I. E. , the interaction of a rare earth metal with alkenes with a terminal alkyne; (2) the Ln-C σ bond is broken with H2; (3) metallic hydride replacement[1], I. E., NaBH4, LiA1H4 and Na can be used to react with organometallic compounds of rare earth metals; (4) the elimination ofβ-H, I. E. , in the presence of LiC1, the elimination of theβ-H of the alkyl compounds of rare earth metals gives the target product. The organohydrides of biindenyl samarium, biindenyl gadolinium and biin denyl dysprosium were obtained with NaH reduction method.

  10. Relations between structure and material properties in earth alkaline silicate basing phosphors; Struktureigenschaftsbeziehungen in Erdalkalisilikat basierenden Leuchtstoffen

    Energy Technology Data Exchange (ETDEWEB)

    Hempel, Wolfgang

    2008-03-19

    This work is basing on the relation between structure and luminescence of Eu{sup 2+} doped Earth-Alkaline-Silicates. After an overview of Earth-Alkaline-Silicates silicates with an additional cation (Li{sup +}, Al{sup 3+}) and an additional anion (Cl{sup -}, N{sup 3-}) are examined in chapter 4 and 5. Basing on this data an relation between structural influence - like ion-radii, anion and coordination polyeder - and phosphor luminescence is set up. The ability of using as an industrial phosphor is made in the final chapter. (orig.)

  11. Impacts of artificial ocean alkalinization on the carbon cycle and climate in Earth system simulations

    Science.gov (United States)

    González, Miriam Ferrer; Ilyina, Tatiana

    2016-06-01

    Using the state-of-the-art emissions-driven Max Planck Institute Earth system model, we explore the impacts of artificial ocean alkalinization (AOA) with a scenario based on the Representative Concentration Pathway (RCP) framework. Addition of 114 Pmol of alkalinity to the surface ocean stabilizes atmospheric CO2 concentration to RCP4.5 levels under RCP8.5 emissions. This scenario removes 940 GtC from the atmosphere and mitigates 1.5 K of global warming within this century. The climate adjusts to the lower CO2 concentration preventing the loss of sea ice and high sea level rise. Seawater pH and the carbonate saturation state (Ω) rise substantially above levels of the current decade. Pronounced differences in regional sensitivities to AOA are projected, with the Arctic Ocean and tropical oceans emerging as hot spots for biogeochemical changes induced by AOA. Thus, the CO2 mitigation potential of AOA comes at a price of an unprecedented ocean biogeochemistry perturbation with unknown ecological consequences.

  12. Lifshitz and other transitions in alkaline-earth 122 pnictides under pressure

    Science.gov (United States)

    Quader, Khandker; Widom, Michael

    2014-10-01

    We carry out T =0 first-principles total energy calculations in the entire set of alkaline 122-pnictides (A Fe2As2 ; A = alkaline-earth element Ca, Sr, Ba, Ra) as a function of hydrostatic pressure. We find multiple distinct transitions to occur, namely an enthalpic transition in which the zero-pressure striped antiferromagnetic orthorhombic (OR-AFM) phase becomes thermodynamically less stable than a competing tetragonal (T) phase, a magnetic transition in which the OR-AFM phase loses its magnetism and orthorhombicity, and a lattice parameter anomaly in which the tetragonal c-axis collapses and a collapsed tetragonal (cT) phase becomes stable. Our results for energy band dispersions and spectra, lattice parameters, enthalpies, magnetism, and elastic constants over a wide range of hydrostatic pressure provide a coherent understanding of these experimentally observed transitions. In particular, the T-cT transition and anomalies in lattice parameters and elastic properties, observed at finite temperatures, are interpreted as arising from proximity to T =0 Lifshitz transitions, wherein pressure causes nontrivial changes in the Fermi surface topology in these materials.

  13. Quantum degenerate mixtures of alkali and alkaline-earth-like atoms.

    Science.gov (United States)

    Hara, Hideaki; Takasu, Yosuke; Yamaoka, Yoshifumi; Doyle, John M; Takahashi, Yoshiro

    2011-05-20

    We realize simultaneous quantum degeneracy in mixtures consisting of the alkali and alkaline-earth-like atoms Li and Yb. This is accomplished within an optical trap by sympathetic cooling of the fermionic isotope ⁶Li with evaporatively cooled bosonic ¹⁷⁴Yb and, separately, fermionic ¹⁷³Yb. Using cross-thermalization studies, we also measure the elastic s-wave scattering lengths of both Li-Yb combinations, |a(⁶Li-¹⁷⁴Yb)| = 1.0 ± 0.2 nm and |a(⁶Li-¹⁷³Yb)| = 0.9 ± 0.2 nm. The equality of these lengths is found to be consistent with mass-scaling analysis. The quantum degenerate mixtures of Li and Yb, as realized here, can be the basis for creation of ultracold molecules with electron spin degrees of freedom, studies of novel Efimov trimers, and impurity probes of superfluid systems.

  14. Theoretical study of the alkaline-earth (LiBe)+ ion: structure, spectroscopy and dipole moments

    Science.gov (United States)

    Ghanmi, C.; Farjallah, M.; Berriche, H.

    2017-03-01

    We study theoretically the structure and spectroscopic properties of the alkali alkaline-earth (LiBe)+ ion. The potential energy curves and their spectroscopic parameters, permanent and transition dipole moments are determined with a quantum chemistry approach. The (LiBe)+ ion is modelled as two valence electron system moving in the field of Be2+ and Li+ cores, which are described by pseudopotentials. In addition, effective core-polarization potentials are included to correct the energy. The molecular calculations are performed using a standard quantum chemistry approach based on the pseudopotential model, Gaussian basis sets, effective core polarization potentials, and full configuration interaction (CI) calculations. The precision of our spectroscopic parameters are discussed by comparison with currently available theoretical results. A rather good agreement is observed for the ground and first excited states. The permanent dipole moments reveal many abrupt changes, which are localized at particular distances corresponding to the positions of the avoided crossings.

  15. Photon Hall Scattering from Alkaline-earth-like atoms and Alkali-like ions

    CERN Document Server

    van Tiggelen, B A

    2016-01-01

    We investigate the possibility of observing a magneto-transverse scattering of photons from alkaline-earth-like atoms as well as alkali-like ions and provide orders of magnitude. The transverse magneto-scattering is physically induced by the interference between two possible quantum transitions of an outer electron in a S-state, one dispersive electric-dipole transition to a P-orbital state and a second resonant electric-quadrupole transition to a P-orbital state. In contrast with previous mechanisms proposed for such an atomic photonic Hall effect, no real photons are scattered by the electric-dipole allowed transition, which increases the ratio of Hall current to background photons significantly. The main experimental challenge is to overcome the small detection threshold, with only 10^{-5} photons scattered per atom per second.

  16. Raman and Rietveld structural characterization of sintered alkaline earth doped ceria

    Energy Technology Data Exchange (ETDEWEB)

    Siqueira Junior, Jose Marcio; Brum Malta, Luiz Fernando; Garrido, Francisco M.S. [Departamento de Quimica Inorganica, Instituto de Quimica, Universidade Federal do Rio de Janeiro, Av. Athos da Silveira Ramos, 149, Centro de Tecnologia, Bloco A, room 632, CEP 68563, 21941-909 Rio de Janeiro, RJ (Brazil); Ogasawara, Tsuneharu [Programa de Engenharia Metalurgica e de Materiais, Coordenacao dos Programas de Pos - Graduacao de Engenharia, Centro de Tecnologia, Universidade Federal do Rio de Janeiro, Ilha do Fundao, CEP 68505, 21941-972 Rio de Janeiro, RJ (Brazil); Medeiros, Marta Eloisa, E-mail: chico@iq.ufrj.br [Departamento de Quimica Inorganica, Instituto de Quimica, Universidade Federal do Rio de Janeiro, Av. Athos da Silveira Ramos, 149, Centro de Tecnologia, Bloco A, room 632, CEP 68563, 21941-909 Rio de Janeiro, RJ (Brazil)

    2012-08-15

    Nanocrystalline calcium and strontium singly doped ceria and co-doped ceria materials for solid electrolytes were prepared via a hydrothermal route. The effect of the hydrothermal treatment time on the solid solution composition was evaluated. Sr doped ceria was the most difficult to form, due to the Sr{sup 2+} large ionic radius. The small crystal size (12-16 nm) of powders allowed sintering into dense ceramic pellets at 1350 Degree-Sign C for 5 h. Raman spectroscopy evidenced a great lattice distortion for Sr doped and co-doped ceria materials, explaining the deterioration of the electrical properties for these ceramics. Besides that, a second phase was detected for Sr doped ceria pellet by using X-ray powder diffraction and Rietveld refinement of XRD data. Impedance measurements showed that Ca-doped ceria behaves as the best ionic conductor ({sigma}{sub g} 390 Degree-Sign C = 1.0 Multiplication-Sign 10{sup -3} S cm{sup -1}) since the nominal composition was achieved; on the other hand, Sr doped ceria performed as resistive materials since Sr incorporation into ceria lattice was critical. These results enhance the close interlace between electrical performance and chemical composition of alkaline earth doped ceria. -- Highlights: Black-Right-Pointing-Pointer Hydrothermally synthesized calcium doped ceria nanoparticles. Black-Right-Pointing-Pointer Incorporation of alkaline earth dopant into ceria lattice. Black-Right-Pointing-Pointer Raman and Rietveld structural characterization. Black-Right-Pointing-Pointer Calcium doped ceria ceramic pellets with high ionic conductivity. Black-Right-Pointing-Pointer Problems associated with the Sr{sup 2+} incorporation into ceria lattice.

  17. Thermal poling of alkaline earth boroaluminosilicate glasses with intrinsically high dielectric breakdown strength

    Science.gov (United States)

    Smith, Nicholas J.; Lanagan, Michael T.; Pantano, Carlo G.

    2012-04-01

    Per the rectification model of thermal poling, it has been proposed that intrinsic breakdown strength plays a strong limiting role in the internal DC fields supported by the glass from the poling process. One might therefore hypothesize proportionately larger second-order nonlinearity (SON) in glasses with intrinsically high dielectric breakdown strength. We test these ideas by thermal poling of two different commercial alkali-free alkaline-earth boroaluminosilicate display glasses—one with barium only (AF45 from Schott), and the other with a mixture of alkaline-earth ions (OA-10 G from NEG). Not only are such compositions relevant from a commercial standpoint, they are also interesting in that they have been recently shown to exhibit remarkably high intrinsic dielectric breakdown strengths of 11-14 MV/cm. Quantitative Maker fringe and stack Maker-fringe measurements provide an accurate evaluation of the poling-induced SON susceptibilities, and indicate maximum χ(2) values of 0.44 and 0.26 pm/V in these glasses. These values are comparable to those reported for silica and other multicomponent glasses. Thus, the hypothesis that higher χ(2) would be observed in high intrinsic breakdown strength glasses was not validated. Based on our application of the rectification model, internal fields of the order 2-4 MV/cm were calculated, which are well below the measured intrinsic breakdown strengths at room temperature. The most plausible explanation for these observations is nonlinear electronic conduction effects taking place within the depletion region at the poling temperature, limiting internal fields to a fraction of the breakdown field.

  18. Global Earthing Systems: Characterization of Buried Metallic Parts

    OpenAIRE

    Tommasini, Riccardo; Colella, Pietro; Pons, Enrico

    2016-01-01

    International Standards IEC 61936-1 and EN 50522 define a Global Earthing System (GES) as the earthing network, created by the interconnection of local earthing systems, that should guarantee the absence of dangerous touch voltages. This is achieved through two effects: the division of the earth fault current between many earthing systems and the creation of a quasi equipotential surface. The second effect can be enhanced by the presence of buried metallic parts, such as light poles and water...

  19. Gyroscopic g factor of rare earth metals

    Science.gov (United States)

    Ogata, Y.; Chudo, H.; Ono, M.; Harii, K.; Matsuo, M.; Maekawa, S.; Saitoh, E.

    2017-02-01

    We develop the in situ magnetization measurement apparatus for observing the Barnett effect consisting of a fluxgate sensor, a high speed rotor with frequencies of up to 1.5 kHz, and a magnetic shield at room temperature. The effective magnetic field (Barnett field) in a sample arising from rotation magnetizes the sample and is proportional to the rotational frequency. The gyroscopic g factor, g ' , of rare earth metals, in particular, Gd, Tb, and Dy, was estimated to be 2.00 ± 0.08, 1.53 ± 0.17, and 1.15 ± 0.32, respectively, from the slopes of the rotation dependence of the Barnett field. This study provides a technique to determine the g ' factor even in samples where the spectroscopic method may not be available.

  20. Optical and electronic properties of conductive ternary nitrides with rare- or alkaline-earth elements

    Science.gov (United States)

    Kassavetis, S.; Hodroj, A.; Metaxa, C.; Logothetidis, S.; Pierson, J. F.; Patsalas, P.

    2016-12-01

    Conductive nitrides, such as TiN, are key engineering materials for electronics, photonics, and plasmonics; one of the essential issues for such applications is the ability of tuning the conduction electron density, the resistivity, and the electron scattering. While enhancing the conduction electron density and blueshifting the intraband absorption towards the UV were easily achieved previously, reducing the conduction electron density and redshifting the intraband absorption into the infrared are still an open issue. The latter is achieved in this work by alloying TiN by rare earth (RE = Sc, Y, La) or alkaline earth (AE = Mg, Ca) atoms in Ti substitutional positions. The produced TixRE1-xN and TixAE1-xN thin film samples were grown by a hybrid arc evaporation/sputtering process, and most of them are stable in the B1 cubic structure. Their optical properties were studied in an extensive spectral range by spectroscopic ellipsometry. The ellipsometric spectra were analyzed and quantified by the Drude-Lorentz model, which provided the conduction electron density, the electron mean free path, and the resistivity. The observed interband transitions are firmly assigned, and the optical and electrical properties of TixRE1-xN and TixAE1-xN are quantitatively correlated with their composition and crystal structure.

  1. Long-range interactions of excited He atoms with the alkaline earth atoms Mg, Ca, and Sr

    KAUST Repository

    Zhang, J.-Y.

    2013-04-05

    Dispersion coefficients for the long-range interactions of the first four excited states of He, i.e., He(2 1, 3 S) and He(2 1, 3 P), with the low-lying states of the alkaline earth atoms Mg, Ca, and Sr are calculated by summing over the reduced matrix elements of multipole transition operators.

  2. Study of the effect hydrogen binding in the solvation of alkaline earth cations with MeOH in nitromethane using 1 H NMR technique and determination of ionic solvation number

    CERN Document Server

    Alizadeh, N

    2001-01-01

    A proton NMR method for the study of the effect hydrogen binding and determination of solvation numbers of alkaline earth cations with methanol (MeOH) in in tromethane (NM) as diluent is described. The method is based on monitoring the resonance frequency of MeOH protons as a function of MeOH to metal ion mole ratio at constant metal ion concentration. the average solvation number of cation, n, at any MeOH/ metal ion mole ration was calculated from the NMR chemical shift-mole ration data and was plotted against the mole ration values. The solvation numbers of alkaline earth cations were obtained from the limiting values of the corresponding n, vs. mole ratio plots.

  3. Conversion of fructose, glucose, and cellulose to 5-hydroxymethylfurfural by alkaline earth phosphate catalysts in hot compressed water.

    Science.gov (United States)

    Daorattanachai, Pornlada; Khemthong, Pongtanawat; Viriya-Empikul, Nawin; Laosiripojana, Navadol; Faungnawakij, Kajornsak

    2012-12-01

    The phosphates of alkaline earth metals (calcium and strontium) synthesized by precipitation process in acetone-water media system were used as catalysts for converting fructose, glucose, and cellulose to 5-hydroxymethylfurfural (HMF) under hot compressed water condition. It was found that the phosphates of calcium and strontium effectively catalyzed the HMF formation from fructose and glucose dehydration and cellulose hydrolysis/dehydration reaction, as compared with the non-catalytic system. The XRD analysis confirmed the CaP(2)O(6) and α-Sr(PO(3))(2) crystalline phases of the catalyst samples, while acid strength of both catalysts was in a range of +3.3 ≤ H(0) ≤ +4.8. From the study, CaP(2)O(6) and α-Sr(PO(3))(2) showed similar catalytic performance toward the dehydration of sugars, providing the HMF yields of 20-21% and 34-39% from glucose and fructose, respectively; whereas the total yield of glucose and HMF from the hydrolysis/dehydration of cellulose over α-Sr(PO(3))(2) (34%) was higher than that over CaP(2)O(6) (17.4%).

  4. A Density Functional Theory Study of Codoping Characteristics of Sulfur with Alkaline Earth in Delafossite CuAlO2

    Science.gov (United States)

    Liu, Qi-Jun; Qin, Han; Liu, Zheng-Tang

    2016-04-01

    The structural, electronic properties and formation energies of sulfur and alkaline earth codoped delafossite CuAlO2 have been investigated using the first-principles density functional theory calculations. Our results reveal that the volume of codoping systems increases with the increasing atomic radius of metal atoms. The formation energies under different growth conditions have been calculated, showing that the codoping systems are formed easily under O-rich growth conditions. Electronic band structures and density of states have been obtained. The decreased bandgaps, enhanced covalence and appearance of electron acceptors after codoping are all good for p-type conductivity. Supported by the National Natural Science Foundation of China under Grant Nos. 11347199, 51402244, and 11547311, the Specialized Research Fund for Doctoral Program of Higher Education of China under Grant No. 20130184120028, the Fundamental Research Fund for the Central Universities, China under Grant Nos. 2682014CX084, 2682014ZT30, and 2682014ZT31, and the fund of the State Key Laboratory of Solidification Processing in NWPU under Grant No. SKLSP201511

  5. Molten metal reactor and method of forming hydrogen, carbon monoxide and carbon dioxide using the molten alkaline metal reactor

    Science.gov (United States)

    Bingham, Dennis N.; Klingler, Kerry M.; Turner, Terry D.; Wilding, Bruce M.

    2012-11-13

    A molten metal reactor for converting a carbon material and steam into a gas comprising hydrogen, carbon monoxide, and carbon dioxide is disclosed. The reactor includes an interior crucible having a portion contained within an exterior crucible. The interior crucible includes an inlet and an outlet; the outlet leads to the exterior crucible and may comprise a diffuser. The exterior crucible may contain a molten alkaline metal compound. Contained between the exterior crucible and the interior crucible is at least one baffle.

  6. Moessbauer effect of the alkaline and alkaline earth metal nitroprusside powders

    CERN Document Server

    Yang, T H; Kim, H S; Hong, C Y; Kim, H B; Cho, H Y; Kim, D Y; Moon, Y S

    2000-01-01

    We observe Moessbauer spectra of Fe atoms centered in nitroprusside anions of sodium nitroprusside (Na sub 2 [Fe(CN) sub 5 NO] 2H sub 2 O). potassium-nitroprusside (K sub 2 [Fe(CN)] sub 5 NO centre dot 2.5H sub 2 O), rubidium nitroprusside (Rb sub 2 [Fe(CN) sub 5 NO centre dot H sub 2 O), magnesium nitroprusside (Mg[Fe(CN) sub 5 NO], calcium nitroprusside (Ca[Fe(CN) sub 5 NO]centre dot 4H sub 2 O), and barium nitroprusside (Ba[Fe(CN) sub 5 NO]centre dot 3H sub 2 O) samples which have photochromic properties. We compare the Moessbauer parameters, the values of the isomer shifts and the quadrupole splittings of the samples with those of a sodium nitroprusside single crystal which is a standard material. The values of the isomer shifts and the quadrupole splittings of the various compounds are close to each other. The values of the line broadening of all samples are between 2.1 GAMMA sub N and 2.5 GAMMA sub N. The Moessbauer Lamb factors (f) are between 0.252(1) and 0.340(2). These values are obtained from the s...

  7. Calculations of Self-diffusion Activation Energies for Alkaline Metals With Embedded Atom Method

    Institute of Scientific and Technical Information of China (English)

    欧阳义芳; 张邦维; 廖树帜

    1994-01-01

    Calculations were performed for the self-diffusion activation energies of monovacancy and both formation and binding energies of divacancies for alkaline metals Li, Na, K, Rb, Cs using the embedded atom method (EAM) model for bcc transition metals developed by the authors recently. The aim of the paper is to extend the application of the new model, to compare the calculated values for self-diffusion with the experimental data and those of previous calculations, and to discuss the intrinsic characteristic of self-diffusion in alkaline metals. The calculated monovacancy migration energies and activation energies are in excellent agreement with experimental data, and the calculated divacancy migration and activation energies are in good agreement with the experimental values available.

  8. Effects of biochars on the availability of heavy metals to ryegrass in an alkaline contaminated soil.

    Science.gov (United States)

    Zhang, Guixiang; Guo, Xiaofang; Zhao, Zhihua; He, Qiusheng; Wang, Shuifeng; Zhu, Yuen; Yan, Yulong; Liu, Xitao; Sun, Ke; Zhao, Ye; Qian, Tianwei

    2016-11-01

    A pot experiment was conducted to investigate the effects of biochars on the availability of heavy metals (Cd, Cu, Mn, Ni, Pb, and Zn) to ryegrass in an alkaline contaminated soil. Biochars only slightly decreased or even increased the availability of heavy metals assesses by chemical extractant (a mixture of 0.05 mol L(-1) ethylenediaminetetraacetic acid disodium, 0.01 mol L(-1) CaCl2, and 0.1 mol L(-1) triethanolamine). The significantly positive correlation between most chemical-extractable heavy metals and the ash content in biochars indicated the positive role of ash in this extraction. Biochars significantly reduced the plant uptake of heavy metals, excluding Mn. The absence of a positive correlation between the chemical-extractable heavy metals and the plant uptake counterparts (except for Mn) indicates that chemical extractability is probably not a reliable indicator to predict the phytoavailability of most heavy metals in alkaline soils treated with biochars. The obviously negative correlation between the plant uptake of heavy metals (except for Mn) and the (O + N)/C and H/C indicates that biochars with more polar groups, which were produced at lower temperatures, had higher efficiency for reducing the phytoavailability of heavy metals. The significantly negative correlations between the plant uptake of Mn and ryegrass biomass indicated the "dilution effect" caused by the improvement of biomass. These observations will be helpful for designing biochars as soil amendments to reduce the availability of heavy metals to plants in soils, especially in alkaline soils.

  9. Surface fractal dimensions and textural properties of mesoporous alkaline-earth hydroxyapatites

    Energy Technology Data Exchange (ETDEWEB)

    Vilchis-Granados, J. [Instituto Nacional de Investigaciones Nucleares, Departamento de Química, A.P. 18-1027, Col. Escandón, Delegación Miguel Hidalgo, C.P. 11801, México, DF (Mexico); Universidad Autónoma del Estado de México, Facultad de Química, Av. Paseo Colón esquina con Paseo Tollocan s/n Toluca, México (Mexico); Granados-Correa, F., E-mail: francisco.granados@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química, A.P. 18-1027, Col. Escandón, Delegación Miguel Hidalgo, C.P. 11801, México, DF (Mexico); Barrera-Díaz, C.E. [Universidad Autónoma del Estado de México, Facultad de Química, Av. Paseo Colón esquina con Paseo Tollocan s/n Toluca, México (Mexico)

    2013-08-15

    This work examines the surface fractal dimensions (D{sub f}) and textural properties of three different alkaline-earth hydroxyapatites. Calcium, strontium and barium hydroxyapatite compounds were successfully synthesized via chemical precipitation method and characterized using X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectrometry, Fourier transform infrared spectroscopy, and N{sub 2}-physisorption measurements. Surface fractal dimensions were determined using single N{sub 2}-adsorption/desorption isotherms method to quantify the irregular surface of as-prepared compounds. The obtained materials were also characterized through their surface hydroxyl group content, determined by the mass titration method. It was found that the D{sub f} values for the three materials covered the range of 0.77 ± 0.04–2.33 ± 0.11; these results indicated that the materials tend to have smooth surfaces, except the irregular surface of barium hydroxyapatite. Moreover, regarding the synthesized calcium hydroxyapatite exhibited better textural properties compared with the synthesized strontium and barium hydroxyapatites for adsorbent purposes. However, barium hydroxyapatite shows irregular surface, indicating a high population of active sites across the surface, in comparison with the others studied hydroxyapatites. Finally, the results showed a linear correlation between the surface hydroxyl group content at the external surface of materials and their surface fractal dimensions.

  10. Photo-bleaching effect in divalent samarium-doped alkaline-earth fluorohalides

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Weiping [Chinese Academy of Sciences, Changchun (China); Jang, Kiwan; Cho, Hyungab; Chung, Yonghwa; Park, Seongtae; Lee, Yongill [Changwon National University, Changwon (Korea, Republic of); Kim, Changdae [Mokpo National University, Mokpo (Korea, Republic of)

    2004-08-15

    When a CW laser was focused on a sample of divalent samarium-doped alkaline-earth fluorohalides (Mg{sub 0.5}Sr{sub 0.5}FCl{sub 0.5}Br{sub 0.5} : Sm{sup 2+} or BaFCl{sub 0.5}Br{sub 0.5} : Sm{sup 2+}), the fluorescence intensity of Sm{sup +2} ions decreased rapidly. Under irradiation from a 488-nm laser with a power density of 10 W/cm{sup 2}, the intensity of the {sup 5}D{sub 0} -> {sup 7}F{sub 0} (Sm{sup 2+}) emission decreased as much as 96 % of its initial intensity in 30 minutes (for an X-ray-reduced sample). The so-called photo-bleaching effect can be influenced by the processes used for sample synthesis, such as the reduction method, the grinding process or X-ray irradiation. The decreasing curves obtained in the photo-bleaching experiments were fitted, a biexponential decreasing mode was found, which included a fast decrease (time constant {approx}tens of seconds) and a slow decrease (time constant {approx}hundreds of seconds). There was no evidence to support the divalent samarium ions being photo-ionized into trivalent samarium ions in the photobleaching process. The most probable mechanism for the photo-bleaching effect involves structural defects and color centers in the samples.

  11. Alkaline earth silicate wools - A new generation of high temperature insulation.

    Science.gov (United States)

    Brown, Robert C; Harrison, Paul T C

    2012-11-01

    Intensive study of the natural asbestiform minerals that cause human diseases, and the consequent understanding of their hazardous characteristics, has enabled the development of manufactured fibres whose physical and/or chemical properties, in particular as they relate to biopersistence, have been adjusted to minimize possible harm to health. A strong driver for the developmentof new high temperature insulation materials wasthe perception of the toxicity of refractory ceramic fibres (RCF)and their classification in the EU as a category 2 carcinogen under Directive 67/548/EEC. Such classification carries with it the requirement for substitution by less hazardous materials. This paper focuses on the development of alkaline earth silicate (AES) wools as a new class of high temperature insulation with the capability of such substitution in a number of applications. These wools have only a low potential to cause harm because they do not persist in lung tissue once deposited, and have produced minimal effects in experimental test systems. AES wools are increasingly being used in a wide range of high temperature applications.

  12. IR and Raman spectroscopic studies of sol–gel derived alkaline-earth silicate glasses

    Indian Academy of Sciences (India)

    Angelos G Kalampounias

    2011-04-01

    IR and Raman spectroscopies have been utilized to study the structure and vibrational modes of sol–gel-derived binary silicate glasses. The present study is motivated by the immense geological significance and focuses on the MO–SiO2 (M = Ca, Mg) binary systems in an effort to unveil the role of the CaO and MgO modifiers when incorporated to the 3D silica structure. Glasses in the composition range = 0, 0.1, 0.2, 0.3 and 0.4 prepared by the sol–gel method were compared with the corresponding glasses formed by appropriate mixing of SiO2 and MO powders through melting and fast cooling. The vibrational spectra of the sol–gel-derived glasses have revealed considerable changes in relative intensities as a function of the MO mole fraction. These changes signify structural modifications on the silica network. The population of the 3 species was found to increase for both modified silicate systems. The rate of increase is more pronounced in the CaO–SiO2 glasses. The extent of network depolymerization in the porous glass is higher at the same content of alkaline earth oxide compared to the bulk glass. The results are indicative of a more `defective’ nature of the sol–gel glasses compared to the corresponding melt-quenched ones.

  13. Collective non-equilibrium spin exchange in cold alkaline-earth atomic clocks

    Science.gov (United States)

    Acevedo, Oscar Leonardo; Rey, Ana Maria

    2016-05-01

    Alkaline-earth atomic (AEA) clocks have recently been shown to be reliable simulators of two-orbital SU(N) quantum magnetism. In this work, we study the non-equilibrium spin exchange dynamics during the clock interrogation of AEAs confined in a deep one-dimensional optical lattice and prepared in two nuclear levels. The two clock states act as an orbital degree of freedom. Every site in the lattice can be thought as populated by a frozen set of vibrational modes collectively interacting via predominantly p-wave collisions. Due to the exchange coupling, orbital state transfer between atoms with different nuclear states is expected to happen. At the mean field level, we observe that in addition to the expected suppression of population transfer in the presence of a large magnetic field, that makes the single particle levels off-resonance, there is also an interaction induced suppression for initial orbital population imbalance. This suppression resembles the macroscopic self-trapping mechanism seen in bosonic systems. However, by performing exact numerical solutions and also by using the so-called Truncated Wigner Approximation, we show that quantum correlations can significantly modify the mean field suppression. Our predictions should be testable in optical clock experiments. Project supported by NSF-PHY-1521080, JILA-NSF-PFC-1125844, ARO, AFOSR, and MURI-AFOSR.

  14. Driving force for the hydration of the swelling clays: case of montmorillonites saturated with alkaline-earth cations.

    Science.gov (United States)

    Salles, Fabrice; Douillard, Jean-Marc; Bildstein, Olivier; Gaudin, Cedric; Prelot, Benedicte; Zajac, Jerzy; Van Damme, Henri

    2013-04-01

    Important structural modifications occur in swelling clays upon water adsorption. The multi-scale evolution of the swelling clay structure is usually evidenced by various experimental techniques. However, the driving force behind such phenomena is still not thoroughly understood. It appears strongly dependent on the nature of the interlayer cation. In the case of montmorillonites saturated with alkaline cations, it was inferred that the compensating cation or the layer surface could control the hydration process and thus the opening of the interlayer space, depending on the nature of the interlayer cation. In the present study, emphasis is put on the impact of divalent alkaline-earth cations compensating the layer charge in montmorillonites. Since no experimental technique offers the possibility of directly determining the hydration contributions related to interlayer cations and layer surfaces, an approach based on the combination of electrostatic calculations and immersion data is developed here, as already validated in the case of montmorillonites saturated by alkaline cations. This methodology allows to estimate the hydration energy for divalent interlayer cations and therefore to shed a new light on the driving force for hydration process occurring in montmorillonites saturated with alkaline-earth cations. Firstly, the surface energy values obtained from the electrostatic calculations based on the Electronegativity Equalization Method vary from 450 mJ m(-2) for Mg-montmorillonite to 1100 mJ m(-2) for Ba-montmorillonite. Secondly, considering both the hydration energy for cations and layer surfaces, the driving force for the hydration of alkaline-earth saturated montmorillonites can be attributed to the interlayer cation in the case of Mg-, Ca-, Sr-montmorillonites and to the interlayer surface in the case of Ba-montmorillonites. These results explain the differences in behaviour upon water adsorption as a function of the nature of the interlayer cation

  15. Investigation on Alkaline-Earth Houses in Jilin Province%吉林碱土民居考察

    Institute of Scientific and Technical Information of China (English)

    王红燕; 朴玉顺

    2012-01-01

    Through extensive research on the residential alkali soil houses in places of the of Yilibao, Sanli bad in the Daan Town,the New Peace Town and Anguang Town, the article clears the distribution and characteristics of the Jilin province alkaline earth houses. Through the residents of the area of alkali land survey- ing and mapping field exploration and focus, the article summarizes the status of the use of alkaline-earth res- idence and makes a detailed analysis of characteristics of alkaline-earth residence. These characteristics are as follows:the alkaline-earth residents living with the ease of local materials, low cost, good thermal insulation properties ,cool, short lifetime, difficult to maintain ,easily damaged and unsightly appearance.%通过对吉林省大安市平安镇一里堡、三里堡、新平安镇、安广镇等地的碱土民居的广泛调研,厘清了吉林省境内碱土民居的分布规律和特点。通过对该地区碱土民居的实地踏勘和重点测绘,总结归纳了碱土民居的使用现状,详细剖析了碱土民居所具有的便于就地取材、造价低廉,保温隔热性能好、冬暖夏凉,使用寿命短、维护困难,易受损、外观不美观等特点。

  16. Ocean-Based Alkalinity Enhancement: Mitigation Potential, Side Effects and the Fate of Added Alkalinity Assessed in an Earth System Model

    Science.gov (United States)

    Gonzalez, M. F.; Ilyina, T.

    2014-12-01

    Artificial ocean alkalinization (AOA) has been proposed as a mean to mitigate climate change and ocean acidification. Whilst the mitigation potential of this geo-engineering technology may sound promising, it poses environmental risks. Within the Priority Program "Climate Engineering" of the German Science Foundation (DFG), we investigate the mitigation potential of AOA to reduce atmospheric CO2 and counteract the consequences of ocean acidification. We are particularly interested in the residence time of the added alkalinity at the ocean surface because it must stay in the upper ocean in order to increase the oceanic CO2 uptake. The mitigation potential, risks and the unintended consequences of this geo-engineering method are also exhaustively studied. These questions are tackled through the analysis of different alkalinity enhancement scenarios in the state-of-the-art Earth system model of the Max Planck Institute for Meteorology (MPI-ESM) in a configuration based on the fifth phase of the Coupled Model Intercomparison Project (CMIP5). Model scenarios are designed so that AOA is performed to keep the atmospheric CO2 concentrations similar to values of the stabilization scenario RCP4.5, while fossil fuel CO2 emissions follow the pathway of the high-CO2 scenario RCP8.5. Alkalinity is added globally into the upper 12 meters of the ocean in different seasons and years. We found that on the time scale of relevance (i.e. from years to decades), season and location are key aspects to take into account in the implementation of AOA. This is because of inhomogeneous vertical mixing of added alkalinity due to the mixed layer depth which is established by the season. We also show that the rate of addition greatly determines impact and outcome of this geo-engineering method. Changes driven by the implementation of this method in the ocean biogeochemistry are also discussed. For instance, the associated changes in the carbon cycle, marine oxygen levels, saturation state of

  17. Alkaline-Earth-Catalysed Cross-Dehydrocoupling of Amines and Hydrosilanes: Reactivity Trends, Scope and Mechanism.

    Science.gov (United States)

    Bellini, Clément; Dorcet, Vincent; Carpentier, Jean-François; Tobisch, Sven; Sarazin, Yann

    2016-03-18

    Alkaline-earth (Ae=Ca, Sr, Ba) complexes are shown to catalyse the chemoselective cross-dehydrocoupling (CDC) of amines and hydrosilanes. Key trends were delineated in the benchmark couplings of Ph3 SiH with pyrrolidine or tBuNH2 . Ae{E(SiMe3)2}2 ⋅(THF)x (E=N, CH; x=2-3) are more efficient than {N^N}Ae{E(SiMe3)2}⋅(THF)n (E=N, CH; n=1-2) complexes (where {N^N}(-) ={ArN(o-C6H4)C(H)=NAr}(-) with Ar=2,6-iPr2 -C6H3) bearing an iminoanilide ligand, and alkyl precatalysts are better than amido analogues. Turnover frequencies (TOFs) increase in the order Ca30 products) includes diamines and di(hydrosilane)s. Kinetic analysis of the Ba-promoted CDC of pyrrolidine and Ph3SiH shows that 1) the kinetic law is rate=k[Ba](1) [amine](0) [hydrosilane](1), 2) electron-withdrawing p-substituents on the arylhydrosilane improve the reaction rate and 3) a maximal kinetic isotopic effect (kSiH/kSiD =4.7) is seen for Ph3SiX (X=H, D). DFT calculations identified the prevailing mechanism; instead of an inaccessible σ-bond-breaking metathesis pathway, the CDC appears to follow a stepwise reaction path with N-Si bond-forming nucleophilic attack of the catalytically competent Ba pyrrolide onto the incoming silane, followed by rate limiting hydrogen-atom transfer to barium. The participation of a Ba silyl species is prevented energetically. The reactivity trend Cametal centre and decreasing Ae-Namide bond strength upon descending Group 2.

  18. Microstructure and creep behavior of magnesium-aluminum alloys containing alkaline and rare earth additions

    Science.gov (United States)

    Saddock, Nicholas David

    In the past few decades governmental regulation and consumer demands have lead the automotive companies towards vehicle lightweighting. Powertrain components offer significant potential for vehicle weight reductions. Recently, magnesium alloys have shown promise for use in powertrain applications where creep has been a limiting factor. These systems are Mg-Al based, with alkaline earth or rare earth additions. The solidification, microstructure, and creep behavior of a series of Mg-4 Al- 4 X:(Ca, Ce, La, and Sr) alloys and a commercially developed AXJ530 (Mg--5 Al--3 Ca--0.15 Sr) alloy (by wt%) have been investigated. The order of decreasing freezing range of the five alloys was: AX44, AXJ530, AJ44, ALa44 and ACe44. All alloys exhibited a solid solution primary alpha-Mg phase surrounded by an interdendritic region of Mg and intermetallic(s). The primary phase was composed of grains approximately an order of magnitude larger than the cellular structure. All alloys were permanent mold cast directly to creep specimens and AXJ530 specimens were provided in die-cast form. The tensile creep behavior was investigated at 175 °C for stresses ranging from 40 to 100 MPa. The order of decreasing creep resistance was: die-cast AXJ530 and permanent mold cast AXJ530, AX44, AJ44, ALa44 and ACe44. Grain size, solute concentration, and matrix precipitates were the most significant microstructural features that influenced the creep resistance. Decreases in grain size or increases in solute concentration, both Al and the ternary addition, lowered the minimum creep rate. In the Mg-Al-Ca alloys, finely distributed Al2Ca precipitates in the matrix also improved the creep resistance by a factor of ten over the same alloy with coarse precipitates. The morphology of the eutectic region was distinct between alloys but did not contribute to difference in creep behavior. Creep strain distribution for the Mg-Al-Ca alloys developed heterogeneously on the scale of the alpha-Mg grains. As

  19. The MCVD synthesis and characterization of water tolerant fiber optic waveguides based on alkaline earth-doped silicas

    Science.gov (United States)

    Farley, Kevin F.

    Optical fibers that transmit throughout the entire telecommunications spectrum (1.2--1.7 mum) are presently manufactured by the removal of hydrogen or OH from the host preform glass. Hydrogen-oxygen torches are utilized in the conventional preform manufacturing process, but result in the formation of hydroxyls in germanium-doped silica fiber. The hydroxyl species generate unacceptably high losses for long haul telecommunications systems. This thesis has explored an alternative strategy for reducing OH-related absorption in silica-based glasses. Alkaline earth modifiers have been introduced via the modified chemical vapor deposition (MCVD) process to successfully damp out and dramatically reduce the extrinsic attenuation associated with both water and hydrogen. Specifically, alkaline earth ions were introduced into alumino-silicate glasses to form MgO-Al2O3-SiO2, CaO-Al 2O3-SiO2, and SrO-Al2O3-SiO 2 compositions. The utilization of halide precursors based on the vapor delivery of rare earths was incorporated into the existing MCVD set-up to fabricate these optical preforms. Both the bulk preforms and fibers drawn from them were characterized to determine relevant optical properties, including the attenuation, index profiles and extinction coefficients arising from OH in each host. The data indicate that modification of the silica glass structure through the additions of modifying ions can significantly reduce OH related absorption. For example, the doping of alkaline earth ions decreased the extinction coefficient measured at the 1.39 mum) OH overtone, to values reinforced by a series of experiments documenting their resistance to hydrogen induced losses.

  20. Immobilization of Penaeus merguiensis alkaline phosphatase on gold nanorods for heavy metal detection.

    Science.gov (United States)

    Homaei, Ahmad

    2017-02-01

    Biotechnology of enzyme has gained popularity due to the growing need for novel environmental technologies and the development of innovative mass-production. The work describes the original application of biosensors based on Penaeus merguiensis alkaline phosphatase (PM ALP) immobilized on gold nanorods (GNRs) to heavy metal determination. Penaeus merguiensis alkaline phosphatase (PM ALP) was immobilized on gold nanorods (GNRs) by ionic exchange and hydrophobic interactions. The optimum pH and temperature for maximum enzyme activity for the immobilized PM ALP are identified to be 11.0 and 60°C, respectively, for the hydrolysis of para-Nitrophenylphosphate (p-NPP). The kinetic studies confirm the Michaelis-Menten behavior and suggests overall slightly decrease in the performance of the immobilized enzyme with reference to the free enzyme. Km and Vmax values were 0.32µm and 54µm. min(-1) for free and 0.39µm and 48µmmin(-1) for immobilized enzymes, respectively. Similarly, the thermal stability, storage stability and stability at extreme pH of the enzyme is found to increase after the immobilization. The inhibitory effect heavy metal ions was studied on free and immobilized PM ALP. The bi-enzymatic biosensor were tested to study the influence of heavy metal ions and pesticides on the corresponding enzyme. The obtained high stability and lower decrease in catalytic efficiency suggested the great potential and feasibility of immobilized PM ALP nanobiocatalyst in efficient and apply the biosensor in total toxic metal content determination.

  1. Halogen-abstraction reactions from chloromethane and bromomethane molecules by alkaline-earth monocations.

    Science.gov (United States)

    Redondo, Pilar; Largo, Antonio; Rayón, Víctor Manuel; Molpeceres, Germán; Sordo, José Ángel; Barrientos, Carmen

    2014-08-14

    The reactions, in the gas phase, between alkali-earth monocations (Mg(+), Ca(+), Sr(+), Ba(+)) and CH3X (X = Cl, Br) have been theoretically studied. The stationary points on the potential energy surfaces were characterized at the Density Functional Theory level on the framework of the mPW1K functional with the QZVPP Ahlrichs's basis sets. A complementary kinetics study has also been performed using conventional/variational microcanonical transition state theory. In the reactions of Mg(+) with either chloro- or bromomethane the transition structure lies in energy clearly above the reactants rendering thermal activation of CH3Cl or CH3Br extremely improbable. The remaining reactions are exothermic and barrierless processes; thus carbon-halogen bonds in chloro- or bromomethane can be activated by calcium, strontium or barium monocations to obtain the metal halogen cation and the methyl radical. The Mulliken population analysis for the stationary points of the potential energy surfaces supports a "harpoon"-like mechanism for the halogen-atom abstraction processes. An analysis of the bonding situation for the stationary points on the potential energy surface has also been performed in the framework of the quantum theory of atoms in molecules.

  2. Method for treating rare earth-transition metal scrap

    Science.gov (United States)

    Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.; Jones, Lawrence L.

    1992-12-29

    Rare earth-transition metal (e.g., iron) scrap (e.g., Nd-Fe-B scrap) is flux (slag) remelted to reduce tramp non-metallic impurities, such as oxygen and nitrogen, and metallic impurities, such as Li, Na, Al, etc., picked up by the scrap from previous fabrication operations. The tramp impurities are reduced to concentrations acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. The scrap is electroslag or inductoslag melted using a prefused, rare earth fluoride-bearing flux of CaF.sub.2, CaCl.sub.2 or mixtures thereof or the slag resulting from practice of the thermite reduction process to make a rare earth-iron alloy.

  3. Catalytic decomposition of hydrogen peroxide on anthraquinonecyanine and phthalocyanine metal complexes in acid and alkaline electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Pobedinskiy, S.N.; Trofimenko, A.A.; Zharnikova, M.A.

    1985-12-01

    A study of octaoxyanthraquinonecyanines (OOATsM) and phthalocyanines (FTs) of cobalt, iron, and manganese determined their catalytic activity in the hydrogen peroxide decomposition reaction. Hydrogen peroxide decomposition on OOATsM and FTs of the metals studied follows the kinetic mechanisms of a reaction of the first order regardless of the central ion of the metal. Complexes with a central atom of iron are most active in decomposition of hydrogen peroxide. Catalytic activity of FTsFe exceeds that of FTsCo more than 10-fold. FTs are 10-fold greater than OOATsM in catalytic activity. Change from an acid to an alkali medium did not affect the kinetic mechanisms of the decomposition reaction but the reaction rate on both a carrier and on metal complexes is higher in an alkaline medium than in an acid medium. The affect of an alkaline medium on the hydrogen peroxide decomposition rate is greater for FTS complexes than for anthraquinone-cyanines. 5 references, 2 figures.

  4. Superconductivity at 31 K in Alkaline Metal-Doped Cobalt Oxides

    Institute of Scientific and Technical Information of China (English)

    闻海虎; 杨海朋; 鲁希锋; 闫静

    2003-01-01

    By using a simple solid reaction method, we have fabricated alkaline metal doped cobalt oxides Anx CoO2+δ(An = Na, K). The magnetic measurement shows a superconducting-like diamagnetic signal at 31 K based on a strong superparamagnetic signal. Below 31 K, the magnetization hysteresis loops contain a strong rough linear superparamagnetic background and a superconducting hysteresis. The typical magnetization hysteresis loops for a type-Ⅱ superconductor are found. Preliminary resistive data also show a fast dropping of resistance below Tc.These give indication of superconductivity below 31 K in Anx CoO2+δ (An = Na, K).

  5. Large gem diamonds from metallic liquid in Earth's deep mantle.

    Science.gov (United States)

    Smith, Evan M; Shirey, Steven B; Nestola, Fabrizio; Bullock, Emma S; Wang, Jianhua; Richardson, Stephen H; Wang, Wuyi

    2016-12-16

    The redox state of Earth's convecting mantle, masked by the lithospheric plates and basaltic magmatism of plate tectonics, is a key unknown in the evolutionary history of our planet. Here we report that large, exceptional gem diamonds like the Cullinan, Constellation, and Koh-i-Noor carry direct evidence of crystallization from a redox-sensitive metallic liquid phase in the deep mantle. These sublithospheric diamonds contain inclusions of solidified iron-nickel-carbon-sulfur melt, accompanied by a thin fluid layer of methane ± hydrogen, and sometimes majoritic garnet or former calcium silicate perovskite. The metal-dominated mineral assemblages and reduced volatiles in large gem diamonds indicate formation under metal-saturated conditions. We verify previous predictions that Earth has highly reducing deep mantle regions capable of precipitating a metallic iron phase that contains dissolved carbon and hydrogen.

  6. Three interesting coordination compounds based on metalloligand and alkaline-earth ions: Syntheses, structures, thermal behaviors and magnetic property

    Science.gov (United States)

    Zhou, Qiang; Qian, Jun; Zhang, Chi

    2016-09-01

    Based on metalloligand LCu ([Cu(2,4-pydca)2]2-, 2,4-pydca2- = pyridine-2,4-dicarboxylate) and alkaline-earth ions (Ca2+, Sr2+, and Ba2+), three interesting coordination compounds, [Ca(H2O)7][LCu·H2O]·H2O (1), {Sr[LCu·H2O]·4H2O}n (2), and {Ba[LCu·H2O]·8H2O}n (3), have been synthesized and well-characterized by elemental analysis, infrared spectroscopy, thermogravimetric and single-crystal X-ray diffraction analysis. X-ray crystallographic studies reveal that 1 features a discrete 0D coordination compound, while 2 and 3 exhibit the 2D network and 1D chain structures, respectively. Compound 2 is constructed from {LCu}2 dimers connected with {Sr2} units, which is fabricated by two Sr2+ ions bridged via two μ2-O bridges, while compound 3 is formed by 1D {Ba}n chain linked with metalloligands LCu and exhibits an interesting sandwich like chain structure. It is noted that the coordination numbers of alkaline-earth ions are in positive correlation with their radiuses. Moreover, the magnetic property of compound 2 has been studied.

  7. Electrons and Spin Waves in Heavy Rare Earth Metals

    DEFF Research Database (Denmark)

    Mackintosh, A. R.

    1972-01-01

    Although the main principles governing the magnetic interactions and magnetic ordering in rare earth metals have been qualitatively understood for some time, it is only relatively recently that a sufficiently detailed study has been made of their electronic and magnetic excitations to place...

  8. Modification of TiO{sub 2} electrode with a series of alkaline-earth carbonates. Performance improvement of quasi-solid-state dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhan, Chun; Wang, Liduo; Wu, Xueming; Qiu, Yong [Ministry of Education, Beijing (China). Key Lab of Organic Optoelectronics and Molecular Engineering; Tsinghua Univ., Beijing (China). Dept. of Chemistry

    2008-07-01

    In this paper, alkaline-earth carbonates (CaCO{sub 3}, SrCO{sub 3} and BaCO{sub 3}) modified TiO{sub 2} electrodes are synthesized by dipping TiO{sub 2} electrode into alkaline-earth hydroxide or alkaline-earth acetate aqueous solutions. When applied to quasi-solid-state DSSC, hydroxide-treated TiO{sub 2} electrodes have increased open-circuit photovoltages (Voc). Among the three alkaline-earth hydroxides, Ba(OH){sub 2} treatment improved the DSSC performance best. The Voc improves from 0.66 V to 0.71 V and the overall conversion efficiency ({eta}) improves by 15% under100 mW/cm{sup 2}. As to acetates, not only the Voc is increased (from 0.68V to 0.74V), but also short-circuit photocurrent(Isc) is improved by Sr(OAc){sub 2} Ba(OAc){sub 2} The overall conversion efficiency improves by 22%. Dark current measurement indicate that in the presence of alkaline-earth carbonates, the TiO2 conduction band shifts to the negative direction, leading to the increase in Voc.

  9. Model for trace metal exposure in filter-feeding flamingos at alkaline Rift Valley Lake, Kenya

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Y.M.; DiSante, C.J.; Lion, L.W. [Cornell Univ., Ithaca, NY (United States). School of Civil and Environmental Engineering; Thampy, R.J.; Raini, J.A. [Worldwide Fund for Nature, Nakuru (Kenya). Lake Nakuru Conservation and Development Project; Motelin, G.K. [Egerton Univ., Njoro (Kenya). Dept. of Animal Health

    1998-11-01

    Toxic trace metals have been implicated as a potential cause of recent flamingo kills at Lake Nakuru, Kenya. Chromium (Cr), copper (Cu), lead (Pb), and zinc (Zn) have accumulated in the lake sediments as a result of unregulated discharges and because this alkaline lake has no natural outlet. Lesser flamingos (Phoeniconaias minor) at Lake Nakuru feed predominantly on the cyanobacterium Spirulina platensis, and because of their filter-feeding mechanism, they are susceptible to exposure to particle-bound metals. Trace metal adsorption isotherms to lake sediments and S. platensis were obtained under simulated lake conditions, and a mathematical model was developed to predict metal exposure via filter feeding based on predicted trace metal phase distribution. Metal adsorption to suspended solids followed the trend Pb {much_gt} Zn > Cr > Cu, and isotherms were linear up to 60 {micro}g/L. Adsorption to S. platensis cells followed the trend Pb {much_gt} Zn > Cu > Cr and fit Langmuir isotherms for Cr, Cu and Zn and a linear isotherm for Pb. Predicted phase distributions indicated that Cr and Pb in Lake Nakuru are predominantly associated with suspended solids, whereas Cu and Zn are distributed more evenly between the dissolved phase and particulate phases of both S. platensis and suspended solids. Based on established flamingo feeding rates and particle size selection, predicted Cr and Pb exposure occurs predominantly through ingestion of suspended solids, whereas Cu and Zn exposure occurs through ingestion of both suspended solids and S. platensis. For the lake conditions at the time of sampling, predicted ingestion rates based on measured metal concentrations in lake suspended solids were 0.71, 6.2, 0.81, and 13 mg/kg-d for Cr, Cu, Pb, and Zn, respectively.

  10. Dispersion coefficients for the interaction of inert gas atoms with alkali and alkaline earth ions and alkali atoms with their singly ionized ions

    CERN Document Server

    Singh, Sukhjit; Sahoo, B K; Arora, Bindiya

    2016-01-01

    We report the dispersion coefficients for the interacting inert gas atoms with the alkali ions, alkaline earth ions and alkali atoms with their singly charged ions. We use our relativistic coupled-cluster method to determine dynamic dipole and quadrupole polarizabilities of the alkali atoms and singly ionized alkaline earth atoms, whereas a relativistic random phase approximation approach has been adopted to evaluate these quantities for the closed-shell configured inert gas atoms and the singly and doubly ionized alkali and alkaline earth atoms, respectively. Accuracies of these results are adjudged from the comparison of their static polarizability values with their respective experimental results. These polarizabilities are further compared with the other theoretical results. Reason for the improvement in the accuracies of our estimated dispersion coefficients than the data listed in [At. Data and Nucl. Data Tables 101, 58 (2015)] are discussed. Results for some of the atom-ion interacting systems were not...

  11. Structural and spectroscopic studies of water-alkaline earth ion micro clusters: an alternate approach using genetic algorithm in conjunction with quantum chemical methods

    Science.gov (United States)

    Ganguly Neogi, S.; Chaudhury, P.

    2014-08-01

    We present an approach of using a stochastic optimization technique namely genetic algorithm in association with quantum chemical methods to first elucidate structure and then infrared spectroscopy and thermochemistry of water-alkaline earth metal ion clusters. We show that an initial determination of structure using stochastic techniques and following it up with quantum chemical calculation can lead to much faster convergence to high quality structures for these systems. Infrared spectroscopic, thermochemical calculations and natural population analysis based charges on the central metal ions are done to further ascertain the correctness of the structures using our technique. We have done a comparative study with a pure density functional theory calculation and have shown that even for very poor starting guess geometries genetic algorithm in conjunction with density functional theory indeed converges to global structure while pure density functional theory can encounter problems in certain situations to arrive at global geometry. We have also discussed usefulness of Unimodal Normal distribution crossover for handling situation with real coded variables.

  12. Recovery of rare earth metals through biosorption:An overview

    Institute of Scientific and Technical Information of China (English)

    Nilanjana Das; Devlina Das

    2013-01-01

    Rare earth metals (REMs) are a series of 17 elements that have widespread and unique applications in high technology, power generation, communications, and defense industries. These resources are also pivotal to emergent sustainable energy and car-bon alternative technologies. Recovery of REMs is interesting due to its high market prices along with various industrial applications. Conventional technologies, viz. precipitation, filtration, liquid-liquid extraction, solid-liquid extraction, ion exchange, super critical extraction, electrowinning, electrorefining, electroslag refining, etc., which have been developed for the recovery of REMs, are not economically attractive. Biosorption represents a biotechnological innovation as well as a cost effective excellent tool for the recovery of rare earth metals from aqueous solutions. A variety of biomaterials such as algae, fungi, bacteria, resin, activated carbon, etc., have been reported to serve as potential adsorbents for the recovery of REMs. The metal binding mechanisms, as well as the parameters in-fluencing the uptake of rare earth metals and isotherm modeling are presented here. This article provides an overview of past achievements and current scenario of the biosorption studies carried out using some promising biosorbents which could serve as an economical means for recovering REMs. The experimental findings reported by different workers will provide insights into this re-search frontier.

  13. Catalysis using hydrous metal oxide ion exchanges

    Science.gov (United States)

    Dosch, Robert G.; Stephens, Howard P.; Stohl, Frances V.

    1985-01-01

    In a process which is catalyzed by a catalyst comprising an active metal on a carrier, said metal being active as a catalyst for the process, an improvement is provided wherein the catalyst is a hydrous, alkali metal or alkaline earth metal titanate, zirconate, niobate or tantalate wherein alkali or alkaline earth metal cations have been exchanged with a catalytically effective amount of cations of said metal.

  14. Catalysis using hydrous metal oxide ion exchangers

    Science.gov (United States)

    Dosch, R.G.; Stephens, H.P.; Stohl, F.V.

    1983-07-21

    In a process which is catalyzed by a catalyst comprising an active metal on a carrier, said metal being active as a catalyst for the process, an improvement is provided wherein the catalyst is a hydrous, alkali metal or alkaline earth metal titanate, zirconate, niobate or tantalate wherein alkali or alkaline earth metal cations have been exchanged with a catalytically effective amount of cations of said metal.

  15. Chemoselective single-site Earth-abundant metal catalysts at metal-organic framework nodes

    Science.gov (United States)

    Manna, Kuntal; Ji, Pengfei; Lin, Zekai; Greene, Francis X.; Urban, Ania; Thacker, Nathan C.; Lin, Wenbin

    2016-08-01

    Earth-abundant metal catalysts are critically needed for sustainable chemical synthesis. Here we report a simple, cheap and effective strategy of producing novel earth-abundant metal catalysts at metal-organic framework (MOF) nodes for broad-scope organic transformations. The straightforward metalation of MOF secondary building units (SBUs) with cobalt and iron salts affords highly active and reusable single-site solid catalysts for a range of organic reactions, including chemoselective borylation, silylation and amination of benzylic C-H bonds, as well as hydrogenation and hydroboration of alkenes and ketones. Our structural, spectroscopic and kinetic studies suggest that chemoselective organic transformations occur on site-isolated, electron-deficient and coordinatively unsaturated metal centres at the SBUs via σ-bond metathesis pathways and as a result of the steric environment around the catalytic site. MOFs thus provide a novel platform for the development of highly active and affordable base metal catalysts for the sustainable synthesis of fine chemicals.

  16. Bacterial degradation of cyanide and its metal complexes under alkaline conditions.

    Science.gov (United States)

    Luque-Almagro, Víctor M; Huertas, María-J; Martínez-Luque, Manuel; Moreno-Vivián, Conrado; Roldán, M Dolores; García-Gil, L Jesús; Castillo, Francisco; Blasco, Rafael

    2005-02-01

    A bacterial strain able to use cyanide as the sole nitrogen source under alkaline conditions has been isolated. The bacterium was classified as Pseudomonas pseudoalcaligenes by comparison of its 16S RNA gene sequence to those of existing strains and deposited in the Coleccion Espanola de Cultivos Tipo (Spanish Type Culture Collection) as strain CECT5344. Cyanide consumption is an assimilative process, since (i) bacterial growth was concomitant and proportional to cyanide degradation and (ii) the bacterium stoichiometrically converted cyanide into ammonium in the presence of l-methionine-d,l-sulfoximine, a glutamine synthetase inhibitor. The bacterium was able to grow in alkaline media, up to an initial pH of 11.5, and tolerated free cyanide in concentrations of up to 30 mM, which makes it a good candidate for the biological treatment of cyanide-contaminated residues. Both acetate and d,l-malate were suitable carbon sources for cyanotrophic growth, but no growth was detected in media with cyanide as the sole carbon source. In addition to cyanide, P. pseudoalcaligenes CECT5344 used other nitrogen sources, namely ammonium, nitrate, cyanate, cyanoacetamide, nitroferricyanide (nitroprusside), and a variety of cyanide-metal complexes. Cyanide and ammonium were assimilated simultaneously, whereas cyanide strongly inhibited nitrate and nitrite assimilation. Cyanase activity was induced during growth with cyanide or cyanate, but not with ammonium or nitrate as the nitrogen source. This result suggests that cyanate could be an intermediate in the cyanide degradation pathway, but alternative routes cannot be excluded.

  17. Luminescence enhancement of rare earth ions by metal nanostructures

    Institute of Scientific and Technical Information of China (English)

    G.A.Denisenko

    2009-01-01

    Well-ordered metal structures,i.e.arrays of nanosized tips on silver surface for studies of the luminescence enhancement of absorbed media with rare earth ions were used.These arrays were prepared by the metal evaporation on track membranes.Calculations of resonance frequencies of tips regarded as semispheroids were done taking into account the interaction between dipoles of tips.They were used to discuss experimental results for media with Eu(NO3)3·6H2O salt basing on data for bulk silver dielectric function.

  18. Suitable alkaline for graphene peeling grown on metallic catalysts using chemical vapor deposition

    Science.gov (United States)

    Karamat, S.; Sonuşen, S.; Çelik, Ü.; Uysallı, Y.; Oral, A.

    2016-04-01

    In chemical vapor deposition, the higher growth temperature roughens the surface of the metal catalyst and a delicate method is necessary for the transfer of graphene from metal catalyst to the desired substrates. In this work, we grow graphene on Pt and Cu foil via ambient pressure chemical vapor deposition (AP-CVD) method and further alkaline water electrolysis was used to peel off graphene from the metallic catalyst. We used different electrolytes i.e., sodium hydroxide (NaOH), potassium hydroxide (KOH), lithium hydroxide (LiOH) and barium hydroxide Ba(OH)2 for electrolysis, hydrogen bubbles evolved at the Pt cathode (graphene/Pt/PMMA stack) and as a result graphene layer peeled off from the substrate without damage. The peeling time for KOH and LiOH was ∼6 min and for NaOH and Ba(OH)2 it was ∼15 min. KOH and LiOH peeled off graphene very efficiently as compared to NaOH and Ba(OH)2 from the Pt electrode. In case of copper, the peeling time is ∼3-5 min. Different characterizations like optical microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy were done to analyze the as grown and transferred graphene samples.

  19. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite for methanol synthesis

    Science.gov (United States)

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1993-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  20. Main group chemistry of 9-hydroxophenalenone: Syntheses and structural characterization of the alkaline earth and zinc complexes

    Indian Academy of Sciences (India)

    Arup Mukherjee; Prinson P Samuel; Carola Schulzke; Swadhin K Mandal

    2014-09-01

    Herein, we report the synthesis and characterization of 9-hydroxophenalenone based alkaline earth and zinc complexes.The reaction of 9-hydroxophenalenone (HO,O-PLY (1)) with one equivalent of KN(SiMe3)2 and MI2 in THF yields heteroleptic complexes [(O,O-PLY)M(THF)]I [M= Mg (2), Ca (3), Sr (4), Ba (5); n = 1-4], while use of two equivalents of KN(SiMe3)2 in THF (with respect to PLY) produces homoleptic complex (O,O-PLY)2Mg(THF)2 (6). Moreover, reaction between two equivalents of 1 with one equivalent of ZnMe2 in THF produces complex (O,O-PLY)2Zn(THF)2 (7). All these complexes were characterized by NMR spectroscopy and elemental analyses. The solid state structures of complexes 2, 6 and 7 were established by single crystal X-ray diffraction analysis.

  1. High-T sub c thin films on low microwave loss alkaline-rare-earth-aluminate crystals

    Energy Technology Data Exchange (ETDEWEB)

    Sobolewski, R.; Gierlowski, P.; Kula, W.; Zarembinski, S.; Lewandowski, S.J.; Berkowski, M.; Pajaczkowska, A. (Instytut Fizyki, Polska Akatlemia Nauk, Al. Lotnikow 32/46, PL-02668 Warszawa (PL)); Gorshunov, B.P.; Lyudmirsky, D.B.; Sirotinsky, O.I. (Institute of General Physics, USSR Academy of Sciences, 38 Vavilova Street, SU-117924 Moscow (SU))

    1991-03-01

    This paper reports on the alkaline-rare-earth aluminates (K{sub 2}NiF{sub 4}-type perovskites) which are an excellent choice as the substrate material for the growth of high-T{sub c} thin films suitable for microwave and far-infrared applications. The CaNdAlO{sub 4}, and SrLaAlO{sub 4} single crystals have been grown by Czochralski pulling and fabricated into the form of (001) oriented wafers. The Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O films deposited on these substrates by a single-target magnetron sputtering exhibited very good superconducting and structural properties.

  2. Rare earth elements and titanium in plants, soils and groundwaters in the alkaline-ultramafic complex of Salitre, MG Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Ceccantini, G. [Instituto de Biociencias, Sao Paulo, (Brazil). Dept. de Botanica; Figueiredo, A.M.G. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Div. de Radioquimica; Sondag, F.; Soubies, F. [ORSTOM, 93 - Bondy (France); Soubies, F. [Universite Paul Sabatier, 31 - Toulouse (France)

    1997-12-31

    The contents of rare earth elements (REE) and titanium in various plant species, in groundwaters and in soils from the alkaline-ultramafic complex of Salitre, have been determined. Due to the the particular mineralogy of the bedrock, REE and Ti exhibit high concentrations in the soils. Despite this, plants generally present REE concentrations within the ranges usually found in plants, and the transfer factor from soil to plant is at least ten times below the range reported in the literature, confirming that the concentrations of REE in the plants are widely independent of the soil content. All species present normalized patterns similar to those of the soils, characterized by an enrichment in light REE. Several plants show Ti concentrations about three times higher than the reference values. It is suggested that in the studied ecosystem, the plant metabolism affect the REE distribution in the groundwaters, leading to an enrichment of the superficial waters in heavy REE

  3. Alkaline earth lead and tin compounds Ae2Pb, Ae2Sn, Ae = Ca, Sr, Ba, as thermoelectric materials

    Directory of Open Access Journals (Sweden)

    David Parker and David J Singh

    2013-01-01

    Full Text Available We present a detailed theoretical study of three alkaline earth compounds Ca2Pb, Sr2Pb and Ba2Pb, which have undergone little previous study, calculating electronic band structures and Boltzmann transport and bulk moduli using density functional theory. We also study the corresponding tin compounds Ca2Sn, Sr2Sn and Ba2Sn. We find that these are all narrow band gap semiconductors with an electronic structure favorable for thermoelectric performance, with substantial thermopowers for the lead compounds at temperature ranges from 300 to 800 K. For the lead compounds, we further find very low calculated bulk moduli—roughly half of the values for the lead chalcogenides, suggestive of soft phonons and hence low lattice thermal conductivity. All these facts indicate that these materials merit experimental investigation as potential high performance thermoelectrics. We find good potential for thermoelectric performance in the environmentally friendly stannide materials, particularly at high temperature.

  4. Physical and optical absorption studies of Fe3+ - ions doped lithium borate glasses containing certain alkaline earths

    Science.gov (United States)

    Bhogi, Ashok; Kumar, R. Vijaya; Kistaiah, P.

    2016-05-01

    Iron ion doped lithium borate glasses with the composition 15RO-25Li2O-59B2O3-1Fe2O3 (where R= Ca, Sr and Ba) have been prepared by the conventional melt quenching technique and characterized to investigate the physical and optical properties using XRD, density, molar volume and UV-Visible spectroscopy. The optical absorption spectra exhibit a band at around 460 nm which is assigned to 6A1g(S) → 4Eg (G) of Fe3+ ions with distorted octahedral symmetry. From ultraviolet absorption edges, the optical band gap and Urbach energies have been evaluated. The effect of alkaline earths on these properties is discussed.

  5. Static and Dynamic Structure Factors with Account of the Ion Structure for High-temperature Alkali and Alkaline Earth Plasmas

    CERN Document Server

    Sadykova, S P; Tkachenko, I M

    2010-01-01

    The $e-e$, $e-i$, $i-i$ and charge-charge static structure factors are calculated for alkali and Be$^{2+}$ plasmas using the method described by Gregori et al. in \\cite{bibGreg2006}. The dynamic structure factors for alkali plasmas are calculated using the method of moments \\cite{bibAdam83}, \\cite{bibAdam93}. In both methods the screened Hellmann-Gurskii-Krasko potential, obtained on the basis of Bogolyubov's method, has been used taking into account not only the quantum-mechanical effects but also the ion structure \\cite{bib73}. PACS: 52.27.Aj (Alkali and alkaline earth plasmas, Static and dynamic structure factors), 52.25.Kn (Thermodynamics of plasmas), 52.38.Ph (X-ray scattering)

  6. Electronic Structure of Rare-Earth Metals. II. Positron Annihilation

    DEFF Research Database (Denmark)

    Williams, R. W.; Mackintosh, Allan

    1968-01-01

    The angular correlation of the photons emitted when positrons annihilate with electrons has been studied in single crystals of the rare-earth metals Y, Gd, Tb, Dy, Ho, and Er, and in a single crystal of an equiatomic alloy of Ho and Er. A comparison of the results for Y with the calculations...... of Loucks shows that the independent-particle model gives a good first approximation to the angular distribution, although correlation effects probably smear out some of the structure. The angular distributions from the heavy rare-earth metals are very similar to that from Y and can be understood...... qualitatively in terms of the relativistic augmented-plane-wave calculations by Keeton and Loucks. The angular distributions in the c direction in the paramagnetic phases are characterized by a rapid drop at low angles followed by a hump, and these features are associated with rather flat regions of Fermi...

  7. Characterization of alkaline-earth oxide additions to the MnO{sub 2} cathode in an aqueous secondary battery

    Energy Technology Data Exchange (ETDEWEB)

    Minakshi, Manickam, E-mail: minakshi@murdoch.edu.au [Extractive Metallurgy, Murdoch University, Murdoch, WA 6150 (Australia); Blackford, Mark [Institute of Materials Engineering, ANSTO, Lucas Heights, NSW 2234 (Australia); Ionescu, Mihail [Institute for Environment Research, ANSTO, Lucas Heights, NSW 2234 (Australia)

    2011-05-19

    Highlights: > Adding MgO in MnO{sub 2} cathode enhances the battery discharge capacity. > Mechanism appears to be different with those of our previously published results. > Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. > Transferred the primary battery into a secondary while using LiOH as electrolyte. - Abstract: The effect of alkaline-earth oxide additions on aqueous rechargeable battery is investigated using microscopic and spectroscopic techniques. The alkaline-earth oxide additions such as magnesium oxide (MgO) and barium oxide (BaO) were physically mixed to the manganese dioxide (MnO{sub 2}) cathode of a cell comprising zinc as an anode and aqueous lithium hydroxide as the electrolyte. The results showed that such additions greatly improved the discharge capacity of the battery (from 145 to 195 for MgO and 265 mAh/g for BaO). Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. With an aim to understand the role of these additives and its improvement in cell performance, we have used microscopy, spectroscopy, ion beam analysis and diffraction based techniques to study the process. Transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy analysis (EDS) results showed evidence of crystalline MnO{sub 2} particles for MgO as additive, whereas, MnO{sub 2} particles with diffused structure leading to mixture of phases is observed for BaO additives which is in agreement with X-ray diffraction (XRD) data. This work relates to improvement in the electrochemical behaviour of the Zn-MnO{sub 2} battery while the MgO additive helps to reduce the formation of manganese and zinc such as hetaerolite that hinders the lithium intercalation.

  8. Influence of alkali and alkaline earth elements on the uptake of radionuclides by Pleurototus eryngii fruit bodies

    Energy Technology Data Exchange (ETDEWEB)

    Guillen, J., E-mail: fguillen@unex.es [LARUEX, Dpt. Applied Physics, Faculty of Veterinary Science, University of Extremadura, Avda. Universidad, s/n, 10071 Caceres (Spain); Baeza, A.; Salas, A. [LARUEX, Dpt. Applied Physics, Faculty of Veterinary Science, University of Extremadura, Avda. Universidad, s/n, 10071 Caceres (Spain)

    2012-04-15

    In the literature, there are many data available on radionuclide contents and their transfer to different species of mushrooms. There are some variables, however, which affect the transfer but are very difficult to observe in collected wild mushrooms. An example is the effect of different concentrations of alkali and alkaline earth elements in the soil. Modification of these concentrations in the soil solution has traditionally been used as a countermeasure to deal with radioactively contaminated areas. In the present work, fruiting bodies of Pleurotus eryngii, a saprophytic mushroom, were grown under controlled laboratory conditions, varying the content of alkali (potassium and caesium) and alkaline earth (calcium and strontium) elements. The transfer of {sup 134}Cs, {sup 85}Sr, and {sup 60}Co (added to the cultures) and of natural {sup 210}Pb was analysed by increasing the content of each stable element considered. A significant, but nonlinear, enhancement of stable caesium and {sup 134}Cs was observed with increasing content of stable caesium in the substrate/mycelium. The transfer of {sup 85}Sr decreased with the addition of each stable cation, whereas the {sup 60}Co and {sup 210}Pb transfers were unaffected. - Highlights: Black-Right-Pointing-Pointer The addition of stable potassium did not affect the uptake of radiocaesium. Black-Right-Pointing-Pointer The addition of stable caesium increased the stable caesium and {sup 134}Cs content in the fruiting bodies of Pleurotus eryngii. Black-Right-Pointing-Pointer The addition of calcium reduced the content of calcium and {sup 85}Sr in the fruiting bodies. Black-Right-Pointing-Pointer These countermeasures did not work properly in the case of {sup 60}Co and {sup 210}Pb, no effect was observed.

  9. Growth of oriented rare-earth-transition-metal thin films

    Energy Technology Data Exchange (ETDEWEB)

    Fullerton, E.E.; Sowers, C.H.; Bader, S.D. [Argonne National Lab., IL (United States); Wu, X.Z. [Argonne National Lab., IL (United States)]|[Northern Illinois Univ., DeKalb, IL (United States)

    1996-04-01

    Rare-earth-transition-metal thin films are successfully grown by magnetron sputtering onto single-crystal MgO substrates with epitaxial W buffer layers. The use of epitaxial W buffer layers allows oriented single-phase films to be grown. Sm-Co films grown onto W(100), have strong in-plane anisotropy and coercivities exceeding 5 T at 5 K whereas Fe-Sm films have strong perpendicular anisotropy and are magnetically soft.

  10. Metal sulfide and rare-earth phosphate nanostructures and methods of making same

    Science.gov (United States)

    Wong, Stanislaus; Zhang, Fen

    2016-06-28

    The present invention provides a method of producing a crystalline rare earth phosphate nanostructure. The method comprising: providing a rare earth metal precursor solution and providing a phosphate precursor solution; placing a porous membrane between the metal precursor solution and the phosphate precursor solution, wherein metal cations of the metal precursor solution and phosphate ions of the phosphate precursor solution react, thereby producing a crystalline rare earth metal phosphate nanostructure.

  11. Suitable alkaline for graphene peeling grown on metallic catalysts using chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Karamat, S., E-mail: shumailakaramat@gmail.com [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey); COMSATS Institute of Information Technology, Islamabad 54000 (Pakistan); Sonuşen, S. [Sabancı Üniversitesi (SUNUM), İstanbul 34956 (Turkey); Çelik, Ü. [Nanomagnetics Instruments, Ankara (Turkey); Uysallı, Y. [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey); Oral, A., E-mail: orahmet@metu.edu.tr [Department of Physics, Middle East Technical University, Ankara 06800 (Turkey)

    2016-04-15

    Graphical abstract: - Highlights: • Graphene layers were grown on Pt and Cu foil via ambient pressure chemical vapor deposition method and for the delicate removal of graphene from metal catalysts, electrolysis method was used by using different alkaline (sodium hydroxide, potassium hydroxide, lithium hydroxide and barium hydroxide). • The delamination speed of PMMA/graphene stack was higher during the KOH and LiOH electrolysis as compare to NaOH and Ba(OH){sub 2}. Ba(OH){sub 2} is not advisable because of the residues left on the graphene surface which would further trapped in between graphene and SiO{sub 2}/Si surface after transfer. The average peeling time in case of Pt electrode is ∼6 min for KOH and LiOH and ∼15 min for NaOH and Ba(OH){sub 2}. • Electrolysis method also works for the Cu catalyst. The peeling of graphene was faster in the case of Cu foil due to small size of bubbles which moves faster between the stack and the electrode surface. The average peeling time was ∼3–5 min. • XPS analysis clearly showed that the Pt substrates can be re-used again. Graphene layer was transferred to SiO{sub 2}/Si substrates and to the flexible substrate by using the same peeling method. - Abstract: In chemical vapor deposition, the higher growth temperature roughens the surface of the metal catalyst and a delicate method is necessary for the transfer of graphene from metal catalyst to the desired substrates. In this work, we grow graphene on Pt and Cu foil via ambient pressure chemical vapor deposition (AP-CVD) method and further alkaline water electrolysis was used to peel off graphene from the metallic catalyst. We used different electrolytes i.e., sodium hydroxide (NaOH), potassium hydroxide (KOH), lithium hydroxide (LiOH) and barium hydroxide Ba(OH){sub 2} for electrolysis, hydrogen bubbles evolved at the Pt cathode (graphene/Pt/PMMA stack) and as a result graphene layer peeled off from the substrate without damage. The peeling time for KOH and Li

  12. Electrodeposition of alkali and alkali-earth metals on liquid lead cathodes in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Caravaca, C.; De Cordoba, G. [CIEMAT/DE/DFN/URAA. Avda. Complutense, 22. 28040 Madrid (Spain)

    2008-07-01

    Pyrochemical processing of spent nuclear fuel leads to the dissolution as chlorides of fission products (FPs) that have to be removed in order to recycle the salt. Precipitation technique have been tested for the removal of these FPs in the LiCl-KCl, salt selected as reference, with different results. Salt decontamination from lanthanides can be easily achieved as solid precipitates of oxychlorides or single phosphates; however, for the alkaline and alkaline-earth metals this technique is not suitable. Within the EUROPART project (VI FP of the EC), a new route that consist of the electrodeposition of these FP on a liquid lead cathode (LLC) has been considered, including the Li and K constituting the electrolyte. First results obtained with Sr and Cs are presented herein. Although according to the thermodynamic potential values, the electrodeposition order on LLC is Ba, Sr, Li, K and Cs, during our experiments it was not possible to distinguish the electrochemical signals corresponding to the individual elements. (authors)

  13. Metal Availability following Paper Mill and Alkaline Residuals Application to Field Crops.

    Science.gov (United States)

    Gagnon, Bernard; Ziadi, Noura; Robichaud, Annie; Karam, Antoine

    2013-01-01

    Land application of residuals from the forest industry can help to restore soil fertility, but few studies have assessed the effects of metal accumulation in plants. An experimental study was initiated in 2000 on a loamy soil at Yamachiche, QC, Canada, to evaluate the effects of repeated annual applications of combined paper mill biosolids, when applied alone or with several liming by-products. This study assessed the accumulation of Cu, Zn, Mo, and Cd in plants and soil after 6 (soybean [ (L.) Merr.]) and 9 [corn ( L.)] crop yr. Wet paper mill biosolids at 0, 30, 60, or 90 Mg ha were surface applied after seeding. Calcitic lime, lime mud, and wood ash were applied wet each at 3 Mg ha with 30 Mg wet paper mill biosolids ha. Repeated applications of paper mill biosolids increased plant and soil metal concentrations after 6 and 9 yr in the order of Cd > Mo (soybean) > Zn > Cu. Liming increased soil pH and Mo availability and decreased Zn and Cd availability. Metals in crop stover responded more positively to applications than those in grains, but the concentrations in plant tissues were generally well below critical values. The Cu/Mo ratio of soybean plants at pH > 6.8 fell below 2:1, however, and may pose a risk for inducing Cu metabolism disorder in ruminants. Results of this study indicate that paper mill biosolids and alkaline residuals, when applied with respect to regulations and soil pH, have a limited effect on metal accumulation in plants and soil.

  14. Theoretical Studies of the Spin Hamiltonian Parameters and Local Distortions for Cu2+ in Alkaline Earth Lead Zinc Phosphate Glasses

    Science.gov (United States)

    Wang, Bo-Kun; Wu, Shao-Yi; Yuan, Zi-Yi; Liu, Zi-Xuan; Jiang, Shi-Xin; Liu, Zheng; Yao, Zi-Jian; Teng, Bao-Hua; Wu, Ming-He

    2016-08-01

    The spin Hamiltonian parameters and local structures are theoretically studied for Cu2+-doped alkaline earth lead zinc phosphate (RPPZ, R=Mg, Ca, Sr, and Ba) glasses based on the high-order perturbation calculations for a tetragonally elongated octahedral 3d9 cluster. The relative elongation ratios are found to be ρ≈3.2%, 4.4%, 4.6%, and 3.3% for R=Mg, Ca, Sr, and Ba, respectively, because of the Jahn-Teller effect. The whole decreasing crystal-field strength Dq and orbital reduction factor k from Mg to Sr are ascribed to the weakening electrostatic coulombic interactions and the increasing probability of productivity of nonbridge oxygen (and hence increasing Cu2+-O2- electron cloud admixtures) under PbO addition, respectively, with increasing alkali earth ionic radius. The anomalies (the largest Dq and the next highest k among the systems) for R=Ba are attributed to the cross linkage of this large cation in the network. The overall increasing order (Mg≤Bacontaining copper dopants.

  15. Investigation of the Alkaline Electrochemical Interface and Development of Composite Metal/Metal-Oxides for Hydrogen and Oxygen Electrodes

    Science.gov (United States)

    Bates, Michael

    Understanding the fundamentals of electrochemical interfaces will undoubtedly reveal a path forward towards a society based on clean and renewable energy. In particular, it has been proposed that hydrogen can play a major role as an energy carrier of the future. To fully utilize the clean energy potential of a hydrogen economy, it is vital to produce hydrogen via water electrolysis, thus avoiding co-production of CO2 inherent to reformate hydrogen. While significant research efforts elsewhere are focused on photo-chemical hydrogen production from water, the inherent low efficiency of this method would require a massive land-use footprint to achieve sufficient hydrogen production rates to integrate hydrogen into energy markets. Thus, this research has primarily focused on the water splitting reactions on base-metal catalysts in the alkaline environment. Development of high-performance base-metal catalysts will help move alkaline water electrolysis to the forefront of hydrogen production methods, and when paired with solar and wind energy production, represents a clean and renewable energy economy. In addition to the water electrolysis reactions, research was conducted to understand the de-activation of reversible hydrogen electrodes in the corrosive environment of the hydrogen-bromine redox flow battery. Redox flow batteries represent a promising energy storage option to overcome the intermittency challenge of wind and solar energy production methods. Optimization of modular and scalable energy storage technology will allow higher penetration of renewable wind and solar energy into the grid. In Chapter 1, an overview of renewable energy production methods and energy storage options is presented. In addition, the fundamentals of electrochemical analysis and physical characterization of the catalysts are discussed. Chapter 2 reports the development of a Ni-Cr/C electrocatalyst with unprecedented mass-activity for the hydrogen evolution reaction (HER) in alkaline

  16. Behavior and distribution of heavy metals including rare Earth elements, thorium, and uranium in sludge from industry water treatment plant and recovery method of metals by biosurfactants application.

    Science.gov (United States)

    Gao, Lidi; Kano, Naoki; Sato, Yuichi; Li, Chong; Zhang, Shuang; Imaizumi, Hiroshi

    2012-01-01

    In order to investigate the behavior, distribution, and characteristics of heavy metals including rare earth elements (REEs), thorium (Th), and uranium (U) in sludge, the total and fractional concentrations of these elements in sludge collected from an industry water treatment plant were determined and compared with those in natural soil. In addition, the removal/recovery process of heavy metals (Pb, Cr, and Ni) from the polluted sludge was studied with biosurfactant (saponin and sophorolipid) elution by batch and column experiments to evaluate the efficiency of biosurfactant for the removal of heavy metals. Consequently, the following matters have been largely clarified. (1) Heavy metallic elements in sludge have generally larger concentrations and exist as more unstable fraction than those in natural soil. (2) Nonionic saponin including carboxyl group is more efficient than sophorolipid for the removal of heavy metals in polluted sludge. Saponin has selectivity for the mobilization of heavy metals and mainly reacts with heavy metals in F3 (the fraction bound to carbonates) and F5 (the fraction bound to Fe-Mn oxides). (3) The recovery efficiency of heavy metals (Pb, Ni, and Cr) reached about 90-100% using a precipitation method with alkaline solution.

  17. Alkaline earth layered benzoates as reusable heterogeneous catalysts for the methyl esterification of benzoic acid

    Directory of Open Access Journals (Sweden)

    Swamy Arêa Maruyama

    2012-01-01

    Full Text Available This paper describes the synthesis and characterization of layered barium, calcium and strontium benzoates and evaluates the potential of these materials as catalysts in the synthesis of methyl benzoate. The methyl esterification of benzoic acid was investigated, where the effects of temperature, alcohol:acid molar ratio and amount of catalyst were evaluated. Ester conversions of 65 to 70% were achieved for all the catalysts under the best reaction conditions. The possibility of recycling these metallic benzoates was also demonstrated, evidenced by unaltered catalytic activity for three consecutive reaction cycles.

  18. Synthesis and luminescence of some rare earth metal complexes

    Science.gov (United States)

    Bochkarev, Mikhail N.; Pushkarev, Anatoly P.

    2016-12-01

    In the present paper the synthesis, photoand electroluminescent properties of new rare earth metal complexes prepared and studied at the Razuvaev Institute of Organometallic Chemistry during the last decade are reviewed. The obtained compounds give luminescence in UV, visible and NIR regions. The substituted phenolates, naphtholates, mercaptobenzothiazolate, 8-oxyquinolinolate, polyfluorinated alcoholates and chalcogenophosphinates were used as ligands. The synthesis and structure of unusual three-nuclear sulfidenitride clusters of Nd and Dy are described. The new excitation mechanism of ytterbium phenolates and naphtholates, which includes the stage of reversible reduction of Yb to divalent state and oxidation of the ligands in the excitation process, is discussed.

  19. Electron-phonon coupling in the rare-earth metals

    DEFF Research Database (Denmark)

    Skriver, Hans Lomholt; Mertig, I.

    1990-01-01

    We have estimated the strength of the mass enhancement of the conduction electrons due to electron-phonon interaction in the rare metals Sc, Y, and La–Lu. The underlying self-consistent energy bands were obtained by means of the scalar relativistic linear-muffin-tin-orbital method, and the electron......-phonon parameters were calculated within the Gaspari-Gyorffy formulation. For the heavier rare earths Gd–Tm spin polarization was included both in the band-structure calculations and in the treatment of the electron-phonon coupling to take into account the spin splitting of the conduction electrons induced by the 4...

  20. Dissolution of glass wool, rock wool and alkaline earth silicate wool: morphological and chemical changes in fibers.

    Science.gov (United States)

    Campopiano, Antonella; Cannizzaro, Annapaola; Angelosanto, Federica; Astolfi, Maria Luisa; Ramires, Deborah; Olori, Angelo; Canepari, Silvia; Iavicoli, Sergio

    2014-10-01

    The behavior of alkaline earth silicate (AES) wool and of other biosoluble wools in saline solution simulating physiological fluids was compared with that of a traditional wool belonging to synthetic vitreous fibers. Morphological and size changes of fibers were studied by scanning electron microscopy (SEM). The elements extracted from fibers were analyzed by inductively coupled plasma atomic emission spectrometry. SEM analysis showed a larger reduction of length-weighted geometric mean fiber diameter at 4.5 pH than at 7.4 pH. At the 7.4 pH, AES wool showed a higher dissolution rate and a dissolution time less than a few days. Their dissolution was highly non-congruent with rapid leaching of calcium. Unlike rock wool, glass wool dissolved more rapidly at physiological pH than at acid pH. Dissolution of AES and biosoluble rock wool is accompanied by a noticeable change in morphology while by no change for glass wool. Biosoluble rock wool developed a leached surface with porous honeycomb structure. SEM analysis showed the dissolution for glass wool is mainly due to breakage transverse of fiber at pH 7.4. AES dissolution constant (Kdis) was the highest at pH 7.4, while at pH 4.5 only biosoluble rockwool 1 showed a higher Kdis.

  1. X-ray Diffraction Studies of the Structure and Thermochemistry of Alkaline-Earth Oxide-Coated Thermionic Cathodes

    Science.gov (United States)

    Karikari, E. K.; Bassey, E.; Wintucky, Edwin G.

    1998-01-01

    NASA LeRC has a broad, active cathode technology development program in which both experimental and theoretical studies are being employed to further development of thermionic cathodes for use as electron sources in vacuum devices for communications and other space applications. One important type of thermionic cathode under development is the alkaline-earth oxide-coated (BaO, SrO, CaO) cathode. Significant improvements in the emission characteristics of this cathode have been obtained through modification of the chemical composition and morphology of the oxide coating, with the best result thus far coming from the addition of In2O3 and Sc2O3. Whereas the In2O3 produces a finer, more uniform particle structure, the exact chemical state and role of the Sc2O3 in the emission enhancement is unknown. The purpose of this cooperative agreement is to combine the studies of the surface chemistry and electron emission at NASA LeRC of chemically modified oxide coatings with a study of the thermochemistry and crystal structure using X-ray diffraction equipment and expertise at Clark Atlanta University (CAU). The study at CAU is intended to provide the description and understanding of the structure and thermochemistry needed for further improvement and optimization of the modified coatings. A description of the experimental procedure, preliminary X-ray diffraction test results, together with the design of an ultrahigh vacuum chamber necessary for high temperature thermochemistry studies will be presented.

  2. Fragment size for calculations on alkaline-earth oxides by the crystal cluster SCF-X/sub approx. /-RW method

    Energy Technology Data Exchange (ETDEWEB)

    Lobach, V.A.; Sobolev, A.B.; Shul' gin, B.V.

    1987-05-01

    Calculations have been performed on the clusters (A/sub x/B/sub y/) (x = 1, 13; y = 6, 14), corresponding to perfect crystals of the alkaline-earth oxides (AEO) MgO, CaO, and SrO by means of methods involving molecular clusters (MC) and crystalline clusters (CC) in the SCF-X/sub approx./-RW method. It is found that MC is unsuitable for describing perfect AEO, because they have a long-range Coulomb interaction and a potential cluster effect. Even in the CC method, the nonstoichiometric composition of (A/sub x/B/sub y/) for x < 13 and y < 14 does not allow one to obtain satisfactory agreement with the observed optical and x-ray spectra. The (A/sub 13/B/sub 14/) and (B/sub 13/A/sub 14/) clusters reproduce satisfactorily the partial composition of the valence band (VB) and the conduction band (CB), as well as the widths of those bands, the fine structure of the K emission spectrum for oxygen in MgO, and the observed electron-density distribution. A study is made of the effects of varying the radii of the spheres on the error from the region between the spheres with muffin-tin averaging.

  3. Correlations in rare-earth transition-metal permanent magnets

    Energy Technology Data Exchange (ETDEWEB)

    Skomski, R., E-mail: rskomski@neb.rr.com; Manchanda, P. [Department of Physics and Astronomy and NCMN, University of Nebraska, Lincoln, Nebraska 68508 (United States); Kashyap, A. [School of Basic Science, IIT Mandi, Mandi, Himachal Pradesh (India)

    2015-05-07

    It is investigated how electron-electron correlations affect the intrinsic properties of rare-earth transition-metal magnets. Focusing on orbital moment and anisotropy, we perform model calculations for 3d-4f alloys and density-functional theory (DFT) calculations for NdCo{sub 5}. On an independent-electron level, the use of a single Slater determinant with broken spin symmetry introduces Hund's rule correlations, which govern the behavior of rare-earth ions and of alloys described by the local spin density approximation (LSDA) and LSDA + U approximations to DFT. By contrast, rare-earth ions in intermetallics involve configuration interactions between two or more Slater determinants and lead to phenomena such as spin-charge distribution. Analyzing DFT as a Legendre transformation and using Bethe's crystal-field theory, we show that the corresponding density functionals are very different from familiar LSDA-type expressions and outline the effect of spin-charge separation on the magnetocrystalline anisotropy.

  4. Synthesis and characterization of crystalline structures based on phenylboronate ligands bound to alkaline earth cations.

    Science.gov (United States)

    Reinholdt, Marc; Croissant, Jonas; Di Carlo, Lidia; Granier, Dominique; Gaveau, Philippe; Bégu, Sylvie; Devoisselle, Jean-Marie; Mutin, P Hubert; Smith, Mark E; Bonhomme, Christian; Gervais, Christel; van der Lee, Arie; Laurencin, Danielle

    2011-08-15

    We describe the preparation of the first crystalline compounds based on arylboronate ligands PhB(OH)(3)(-) coordinated to metal cations: [Ca(PhB(OH)(3))(2)], [Sr(PhB(OH)(3))(2)]·H(2)O, and [Ba(PhB(OH)(3))(2)]. The calcium and strontium structures were solved using powder and single-crystal X-ray diffraction, respectively. In both cases, the structures are composed of chains of cations connected through phenylboronate ligands, which interact one with each other to form a 2D lamellar structure. The temperature and pH conditions necessary for the formation of phase-pure compounds were investigated: changes in temperature were found to mainly affect the morphology of the crystallites, whereas strong variations in pH were found to affect the formation of pure phases. All three compounds were characterized using a wide range of analytical techniques (TGA, IR, Raman, XRD, and high resolution (1)H, (11)B, and (13)C solid-state NMR), and the different coordination modes of phenylboronate ligands were analyzed. Two different kinds of hydroxyl groups were identified in the structures: those involved in hydrogen bonds, and those that are effectively "free" and not involved in hydrogen bonds of any significant strength. To position precisely the OH protons within the structures, an NMR-crystallography approach was used: the comparison of experimental and calculated NMR parameters (determined using the Gauge Including Projector Augmented Wave method, GIPAW) allowed the most accurate positions to be identified. In the case of the calcium compound, it was found that it is the (43)Ca NMR data that are critical to help identify the best model of the structure.

  5. Molecular rare-earth-metal hydrides in non-cyclopentadienyl environments.

    Science.gov (United States)

    Fegler, Waldemar; Venugopal, Ajay; Kramer, Mathias; Okuda, Jun

    2015-02-02

    Molecular hydrides of the rare-earth metals play an important role as homogeneous catalysts and as counterparts of solid-state interstitial hydrides. Structurally well-characterized non-metallocene-type hydride complexes allow the study of elementary reactions that occur at rare-earth-metal centers and of catalytic reactions involving bonds between rare-earth metals and hydrides. In addition to neutral hydrides, cationic derivatives have now become available.

  6. Supramolecular structures constructed from three novel rare earth metal complexes

    Indian Academy of Sciences (India)

    Huaze Dong; Xiaojun Feng; Xia Liu; BiN Zheng; Jianhong Bi; Yan Xue; Shaohua Gou; Yanping Wang

    2015-05-01

    Three rare earth metal supramolecular complexes, {[Tb(2)4](ClO4)3·2H2O(1), [Eu(2)2(H2O)5] (ClO4)3(2) and [Gd(NO3)3(2)2]·2CH3CH2OH(3) ( 2 = 3-Dimethylamino-1-pyridin-2-yl-propenone), have been synthesized and characterized by elemental analysis, IR and single crystal X-ray diffraction. The crystal structure analysis reveals that the coordination numbers of three complexes (1–3) are 8, 9 and 10, respectively. Three complexes assembled into 3D frameworks based on C-H⋯O, O-H⋯O hydrogen bond linkages.

  7. The DNA-binding and bioactivity of rare earth metal complexes.

    Science.gov (United States)

    Yang, Li; Wang, Bochu; Tan, Jun; Zhu, Liancai

    2013-08-01

    Recently more and more attention is paid to the rare earth metal complexes, because the properties of the rare earth metals are similar to those of the transition metals such as the similar atomic and the ionic radius. A large number of rare metal complexes were synthesized, and their bioactivities were also studied. This review highlights recent researches on the interaction of some rare earth metal complexes with DNA, analyzes how the configuration of the complexes influences the binding affinity, and focuses on the pharmacological activities of the complexes, such as anticancer, antibacterial, antioxidant, anti-inflammatory and anti-virus.

  8. Selective trans-membrane transport of alkali and alkaline earth cations through graphene oxide membranes based on cation-π interactions.

    Science.gov (United States)

    Sun, Pengzhan; Zheng, Feng; Zhu, Miao; Song, Zhigong; Wang, Kunlin; Zhong, Minlin; Wu, Dehai; Little, Reginald B; Xu, Zhiping; Zhu, Hongwei

    2014-01-28

    Graphene and graphene oxide (G-O) have been demonstrated to be excellent filters for various gases and liquids, showing potential applications in areas such as molecular sieving and water desalination. In this paper, the selective trans-membrane transport properties of alkali and alkaline earth cations through a membrane composed of stacked and overlapped G-O sheets ("G-O membrane") are investigated. The thermodynamics of the ion transport process reveal that the competition between the generated thermal motions and the interactions of cations with the G-O sheets results in the different penetration behaviors to temperature variations for the considered cations (K(+), Mg(2+), Ca(2+), and Ba(2+)). The interactions between the studied metal atoms and graphene are quantified by first-principles calculations based on the plane-wave-basis-set density functional theory (DFT) approach. The mechanism of the selective ion trans-membrane transportation is discussed further and found to be consistent with the concept of cation-π interactions involved in biological systems. The balance between cation-π interactions of the cations considered with the sp(2) clusters of G-O membranes and the desolvation effect of the ions is responsible for the selectivity of G-O membranes toward the penetration of different ions. These results help us better understand the ion transport process through G-O membranes, from which the possibility of modeling the ion transport behavior of cellular membrane using G-O can be discussed further. The selectivity toward different ions also makes G-O membrane a promising candidate in areas of membrane separations.

  9. Band structure and electrical properties of MBE grown HfO{sub 2} - based alkaline earth Perovskites

    Energy Technology Data Exchange (ETDEWEB)

    Peter, Dudek; Grzegorz, Lupina; Grzegorz, Kozlowski; Jarek, Dabrowski; Gunther, Lippert; Hans-Joachim, Muessig; Thomas, Schroeder [IHP-Microelectronics, Frankfurt, Oder (Germany); Dieter, Schmeisser [BTU, Cottbus (Germany)

    2010-07-01

    Ultra thin dielectric films (<20 nm) deposited on TiN electrodes are interesting for MIM capacitor application. High capacitance density and dielectric permittivity must be accompanied by extremely low leakage currents (10{sup -8} A/cm{sup 2}) at bias 0.5 V. To achieve such low leakage currents, high band gap and proper band alignment is required. Occupied electronic states can be probed with standard laboratory photoemission methods. Probing of unoccupied states is more challenging. Synchrotron based PES in combination with XAS forms a powerful method to study the band alignment. ASAM end station located at the U 49/2 PGM 2 beamline of BESSY II (Berlin) offers excellent conditions for performing such measurements. We investigated HfO{sub 2} - based alkaline earth perovskite - BaHfO{sub 3} with subsequent admixture of TiO{sub 2}, resulting in formation of BaHf{sub 0.5}Ti{sub 0.5}O{sub 3} compound. The analysis of data indicates that band gap for HfO{sub 2} is similar to BaHfO{sub 3} and amounts 5.8 eV; for BaHf{sub 0.5}Ti{sub 0.5}O{sub 3} it decreases to 3.8 eV. We conclude that the addition of TiO{sub 2} to BaHfO{sub 3} increases significantly the dielectric permittivity but also impacts the band gap alignment. The conduction band offset shrinks, influencing the leakage current behavior.

  10. Mixed alkali and alkaline-earth borate Li2Sr4B12O23 single crystal

    Science.gov (United States)

    Reshak, A. H.

    2015-10-01

    A comprehensive theoretical investigation of the electronic band structure, density of states, electron charge density distribution and the optical properties for mixed alkali and alkaline-earth borate Li2Sr4B12O23 (LSBO) single crystals were performed. The experimental geometrical structure was optimized by minimizing the forces acting on each atom. Calculations were performed using the full potential linear augmented plane wave plus local orbitals (FPLAPW + lo) method within the local density approximation (LDA), generalized gradient approximation (GGA) and the recently modified Becke-Johnson potential (mBJ). Our calculations show that LSBO crystal is a direct band gap semiconductor. The calculated band gap is 4.64 eV (LDA), 4.92 eV (GGA) and 5.51 eV (mBJ). An earlier calculation using the CASTEP code within LDA obtained a band gap of about 4.66 eV. To overcome the well-known LDA underestimation of the energy gap we have used GGA and mBJ . We find that mBJ succeed by large amount in bringing the calculated bond lengths in good agreement with the experimental data. Also we found that using mBJ to calculate the optical properties gives a birefringence of about 0.068 (at λ = 586.5 nm) in excellent agreement with the experimental data (0.068 at λ = 586.5 nm). Therefore, we believe that the mBJ calculations reported here show excellent agreement with the experimental data.

  11. Oligomeric rare-earth metal cluster complexes with endohedral transition metal atoms

    Energy Technology Data Exchange (ETDEWEB)

    Steinberg, Simon; Zimmermann, Sina; Brühmann, Matthias; Meyer, Eva; Rustige, Christian; Wolberg, Marike; Daub, Kathrin; Bell, Thomas; Meyer, Gerd, E-mail: gerd.meyer@uni-koeln.de

    2014-11-15

    Comproportionation reactions of rare-earth metal trihalides (RX{sub 3}) with the respective rare-earth metals (R) and transition metals (T) led to the formation of 22 oligomeric R cluster halides encapsulating T, in 19 cases for the first time. The structures of these compounds were determined by single-crystal X-ray diffraction and are composed of trimers ((T{sub 3}R{sub 11})X{sub 15}-type, P6{sub 3}/m), tetramers ((T{sub 4}R{sub 16})X{sub 28}(R{sub 4}) (P-43m), (T{sub 4}R{sub 16})X{sub 20} (P4{sub 2}/nnm), (T{sub 4}R{sub 16})X{sub 24}(RX{sub 3}){sub 4} (I4{sub 1}/a) and (T{sub 4}R{sub 16})X{sub 23} (C2/m) types of structure) and pentamers ((Ru{sub 5}La{sub 14}){sub 2}Br{sub 39}, Cc) of (TR{sub r}){sub n} (n=2–5) clusters. These oligomers are further enveloped by inner (X{sup i}) as well as outer (X{sup a}) halido ligands, which possess diverse functionalities and interconnect like oligomers through i–i, i–a and/or a–i bridges. The general features of the crystal structures for these new compounds are discussed and compared to literature entries as well as different structure types with oligomeric T centered R clusters. Dimers and tetramers originating from the aggregation of (TR{sub 6}) octahedra via common edges are more frequent than trimers and pentamers, in which the (TR{sub r}) clusters share common faces. - Graphical abstract: Rare earth-metal cluster complexes with endohedral transition metal atoms (TR{sub 6}) may connect via common edges or faces to form dimers, trimers, tetramers and pentamers of which the tetramers are the most prolific. Packing effects and electron counts play an important role. - Highlights: • Rare-earth metal cluster complexes encapsulate transition metal atoms. • Oligomers are built via connection of octahedral clusters via common edges or faces. • Dimers through pentamers with closed structures are known. • Tetramers including a tetrahedron of endohedral atoms are the most prolific.

  12. Rare-earth metal prices in the USA ca. 1960 to 1994

    Science.gov (United States)

    Hedrick, James B.

    1997-01-01

    Rare-earth metal prices were compiled from the late 1950s and early 1960s through 1994. Although commercial demand for rare-earth metals began in 1908, as the alloy mischmetal, commercial quantities of a wide range of individual rare-earth metals were not available until the late 1950s. The discovery of a large, high-grade rare-earth deposit at Mountain Pass. CA, USA, in 1949, was significant because it led to the production of commercial quantities or rare-earth elements that reduced prices and encouraged wider application of the materials. The availability of ore from Mountain Pass, and other large rare-earth deposits, especially those in Australia and China, has provided the world with abundant resources for rare-earth metal production. This availability, coupled with improved technology from Government and private-sector metallurgical research, has resulted in substantial decreases in rare-earth metal prices since the late 1950s and early 1960s. Price series for the individual rare-earth metals (except promethium) are quoted on a kilogram basis from the late 1950s and early 1960s through 1994. Prices are given in US dollars on an actual and constant dollar basis. Industrial and economic factors affecting prices during this time period are examined.

  13. High Temperature Alkaline Electrolysis Cells with Metal Foam Based Gas Diffusion Electrodes

    DEFF Research Database (Denmark)

    Chatzichristodoulou, Christodoulos; Allebrod, Frank; Mogensen, Mogens Bjerg

    2016-01-01

    Alkaline electrolysis cells operating at 250°C and 40 bar are able to convert electrical energy into hydrogen at very high efficiencies and power densities. In the present work we demonstrate the application of a PTFE hydrophobic network and Ag nanowires as oxygen evolution electrocatalyst...

  14. Solubility Behavior and Phase Stability of Transition Metal Oxides in Alkaline Hydrothermal Environments

    Energy Technology Data Exchange (ETDEWEB)

    S.E. Ziemniak

    2000-05-18

    The solubility behavior of transition metal oxides in high temperature water is interpreted by recognizing three types of chemical reaction equilibria: metal oxide hydration/dehydration, metal oxide dissolution and metal ion hydroxocomplex formation. The equilibria are quantified using thermodynamic concepts and the thermochemical properties of the metal oxides/ions representative of the most common constituents of construction metal alloys, i.e., element shaving atomic numbers between Z = 22 (Ti) and Z = 30 (Zn), are summarized on the basis of metal oxide solubility studies conducted in the laboratory. Particular attention is devoted to the uncharged metal ion hydrocomplex, M{sup Z}(OH){sub Z}(aq), since its thermochemical properties define minimum solubilities of the metal oxide at a given temperature. Experimentally-extracted values of standard partial molal entropy (S{sup 0}) for the transition metal ion neutral hydroxocomplex are shown to be influenced by ligand field stabilization energies and complex symmetry.

  15. Influence of alkali and alkaline earth ions on the -alkylation of the lower rim phenolic-OH groups of -tert-butyl-calix[4]arene to result in amide-pendants: Template action of K+ and the structure of K+ bound tetra-amide derivative crystallized with a -tert-butylcalix[4]arene anion

    Indian Academy of Sciences (India)

    Amjad Ali; Chebrolu P Rao; Philippe Guionneau

    2008-03-01

    Role of alkali and alkaline earth ions on the formation of calix[4]arene-amide derivatives through -alkylation of the lower rim phenolic-OH groups in general and template action of K+ in particular have been explored. Na+ and K+ ions among alkali, and Ca2+ and Sr2+ ions among alkaline earth have shown tetra-amide derivatives bound to metal ion species. Among all these, potassium salts act as template and yields a K+ bound tetra-amide derivative where the charge is counter balanced by a calix[4] arene-monoanion and the product is crystallographically characterized. Change in the amide precursor used in these -alkylation reactions has no effect on the type of the amide derivative formed. Also demonstrated is a direct one-step reaction for the preparation of 1,3-di-amide derivative in high yield and low reaction period using CsHCO3.

  16. Phase diagram and thermodynamic calculations of alkali and alkaline earth metal zirconates

    Energy Technology Data Exchange (ETDEWEB)

    Dash, S. [Bhabha Atomic Res. Centre, Bombay (India). Fuel Chem. Div.; Sood, D.D. [Bhabha Atomic Res. Centre, Bombay (India). Fuel Chem. Div.; Prasad, R. [Bhabha Atomic Res. Centre, Bombay (India). Fuel Chem. Div.

    1996-02-01

    The ternary phase diagrams and partial pressures of various gaseous species over the equilibrium phase fields have been calculated for the M-Zr-O (M=Li, Na, K, Rb, Cs, Sr and Ba) systems by using the SOLGASMIX-PV program, which computes equilibrium composition by direct minimization of the Gibbs energy of a system. The available experimental Gibbs energy data reported in the literature for binary and ternary compounds were used for these calculations. Where no data exist, values were estimated. These ternary phase diagrams are being reported for the first time, except for the lithium system. (orig.).

  17. Phase diagram and thermodynamic calculations of alkali and alkaline earth metal zirconates

    Science.gov (United States)

    Dash, Smruti; Sood, D. D.; Prasad, R.

    1996-02-01

    The ternary phase diagrams and partial pressures of various gaseous species over the equilibrium phase fields have been calculated for the MZrO (M = Li, Na, K, Rb, Cs, Sr and Ba) systems by using the SOLGASMIX-PV program, which computes equilibrium composition by direct minimization of the Gibbs energy of a system. The available experimental Gibbs energy data reported in the literature for binary and ternary compounds were used for these calculations. Where no data exist, values were estimated. These ternary phase diagrams are being reported for the first time, except for the lithium system.

  18. Topological Dirac nodal lines and surface charges in fcc alkaline earth metals

    Science.gov (United States)

    Hirayama, Motoaki; Okugawa, Ryo; Miyake, Takashi; Murakami, Shuichi

    2017-01-01

    In nodal-line semimetals, the gaps close along loops in k space, which are not at high-symmetry points. Typical mechanisms for the emergence of nodal lines involve mirror symmetry and the π Berry phase. Here we show via ab initio calculations that fcc calcium (Ca), strontium (Sr) and ytterbium (Yb) have topological nodal lines with the π Berry phase near the Fermi level, when spin–orbit interaction is neglected. In particular, Ca becomes a nodal-line semimetal at high pressure. Owing to nodal lines, the Zak phase becomes either π or 0, depending on the wavevector k, and the π Zak phase leads to surface polarization charge. Carriers eventually screen it, leaving behind large surface dipoles. In materials with nodal lines, both the large surface polarization charge and the emergent drumhead surface states enhance Rashba splitting when heavy adatoms are present, as we have shown to occur in Bi/Sr(111) and in Bi/Ag(111). PMID:28074835

  19. Topological Dirac nodal lines and surface charges in fcc alkaline earth metals

    Science.gov (United States)

    Hirayama, Motoaki; Okugawa, Ryo; Miyake, Takashi; Murakami, Shuichi

    2017-01-01

    In nodal-line semimetals, the gaps close along loops in k space, which are not at high-symmetry points. Typical mechanisms for the emergence of nodal lines involve mirror symmetry and the π Berry phase. Here we show via ab initio calculations that fcc calcium (Ca), strontium (Sr) and ytterbium (Yb) have topological nodal lines with the π Berry phase near the Fermi level, when spin-orbit interaction is neglected. In particular, Ca becomes a nodal-line semimetal at high pressure. Owing to nodal lines, the Zak phase becomes either π or 0, depending on the wavevector k, and the π Zak phase leads to surface polarization charge. Carriers eventually screen it, leaving behind large surface dipoles. In materials with nodal lines, both the large surface polarization charge and the emergent drumhead surface states enhance Rashba splitting when heavy adatoms are present, as we have shown to occur in Bi/Sr(111) and in Bi/Ag(111).

  20. Ultra-sensitive conductometric detection of heavy metals based on inhibition of alkaline phosphatase activity from Arthrospira platensis.

    Science.gov (United States)

    Tekaya, Nadèje; Saiapina, Olga; Ben Ouada, Hatem; Lagarde, Florence; Ben Ouada, Hafedh; Jaffrezic-Renault, Nicole

    2013-04-01

    This study is based on the conductometric measurement of alkaline phosphatase activity (APA) from the cyanobacterium, Arthrospira platensis, called Spirulina. Cyanobacterium cells were directly immobilized, by physical adsorption, on the ceramic part of gold interdigitated transducers. This activity was inhibited in the presence of heavy metals and a variation of the local conductivity was measured after addition of the substrate. The Michaelis-Menten constant (Km) was evaluated to be 0.75 mM through a calibration curve of the substrate, disodium 4-nitrophenylphosphate p-nitrophenyl phosphate (pNPP). Inhibition of APA was observed with cadmium and mercury with a detection limit of 10(-20) M. The half maximal inhibitory concentration (IC50) was determined at 10(-19) M for Cd(2+) and 10(-17) M for Hg(2+), and the binding affinity of heavy metal (Ki) was equal to the IC50. On the sensor surface, scanning electron microscopy (SEM) images revealed a remarkable evolution of the cyanobacterium's external surface that was attributable to the first defense mechanism against toxic heavy metals in trace. This effect was also confirmed through the important increase of response time τ(90%) recorded for APA response towards the substrate pNPP after cell exposure to metallic cations. Lifetime of the Spirulina-based biosensor was estimated to be more than 25 days.

  1. Enzymatically mediated bioprecipitation of heavy metals from industrial wastes and single ion solutions by mammalian alkaline phosphatase.

    Science.gov (United States)

    Chaudhuri, Gouri; Shah, Gaurav A; Dey, Pritam; S, Ganesh; Venu-Babu, P; Thilagaraj, W Richard

    2013-01-01

    The study was aimed at investigating the potential use of calf intestinal alkaline phosphatase (CIAP) enzyme in the removal of heavy metals (Cd(2+), Ni(2+), Co(2+) and Cr(3+/6+)) from single ion solutions as well as tannery and electroplating effluents. CIAP mediated bioremediation (white biotechnology) is a novel technique that is eco-friendly and cost effective unlike the conventional chemical technologies. Typical reactions containing the enzyme (CIAP) and p-nitrophenyl phosphate (pNPP) as substrate in Tris-HCl buffer (pH 8 and 11) and either single ion metal solutions (250 ppm and 1000 ppm) or effluents from tannery or electroplating industry were incubated at 37°C for 30 min, 60 min and 120 min. The inorganic phosphate (P(i)) generated due to catalytic breakdown of pNPP complexes free metal ions as metal-phosphate and the amount of metal precipitated was derived by estimating the reduction in the free metal ion present in the supernatant of reactions employing atomic absorption spectrophotometer (AAS). Better precipitation of metal was obtained at pH 11 than at pH 8 and between the two concentrations of different metals tested, an initial metal concentration of 250 ppm in the reaction gave more precipitation than with 1000 ppm. Experimental data showed that at pH 11, the percentage of removal of metal ions (for an initial concentration of 250 ppm) was in the following order: Cd(2+) (80.99%) > Ni(2+) (64.78%) > Cr(3+) > (46.15%) > Co(2+) (36.47%) > Cr(6+) (32.33%). The overall removal of Cr(3+) and Cr(6+) from tannery effluent was 32.77% and 37.39% respectively in 120 min at pH 11. Likewise, the overall removal of Cd(2+), Co(2+) and Ni(2+) from electroplating effluent was 50.42%, 13.93% and 38.64% respectively in 120 min at pH 11. The study demonstrates that bioprecipitation by CIAP may be a viable and environmental friendly method for clean-up of heavy metals from tannery and electroplating effluents.

  2. Process optimization and kinetics for leaching of rare earth metals from the spent Ni-metal hydride batteries.

    Science.gov (United States)

    Meshram, Pratima; Pandey, B D; Mankhand, T R

    2016-05-01

    Nickel-metal hydride batteries (Ni-MH) contain not only the base metals, but valuable rare earth metals (REMs) viz. La, Sm, Nd, Pr and Ce as well. In view of the importance of resource recycling and assured supply of the contained metals in such wastes, the present study has focussed on the leaching of the rare earth metals from the spent Ni-MH batteries. The conditions for the leaching of REMs from the spent batteries were optimized as: 2M H2SO4, 348K temperature and 120min of time at a pulp density (PD) of 100g/L. Under this condition, the leaching of 98.1% Nd, 98.4% Sm, 95.5% Pr and 89.4% Ce was achieved. Besides the rare earth metals, more than 90% of base metals (Ni, Co, Mn and Zn) were also leached out in this condition. Kinetic data for the dissolution of all the rare earth metals showed the best fit to the chemical control shrinking core model. The leaching of metals followed the mechanism involving the chemical reaction proceeding on the surface of particles by the lixiviant, which was corroborated by the XRD phase analysis and SEM-EDS studies. The activation energy of 7.6, 6.3, 11.3 and 13.5kJ/mol was acquired for the leaching of neodymium, samarium, praseodymium and cerium, respectively in the temperature range 305-348K. From the leach liquor, the mixed rare earth metals were precipitated at pH∼1.8 and the precipitated REMs was analyzed by XRD and SEM studies to determine the phases and the morphological features.

  3. Adsorption of rare earth metal ion by algae. Sorui ni yoru kidorui ion no kyuchaku

    Energy Technology Data Exchange (ETDEWEB)

    Kuwabara, T.; Yazawa, A. (Miyagi National College of Technology, Miyagi (Japan))

    1994-02-25

    This paper reports the result of investigations on adsorption of rare earth metal ion by using algae, and adsorption of different metal ions by using egg white and soy bean protein. Rare earth metal ion is adsorbed at a considerably high rate with alga powder of different kinds. The adsorption has been judged to be cation exchange reactive adsorption, while with use of spirulina and chlorella a maximum value of adsorption rate has been observed at pH from 3 to 4.5. Therefore, selective adsorption and separation of metal ions other than rare earth metal ion has become possible. When the blue pigment extracted from spirulina, the spirulina blue, is used, the rare earth metal ion had its selective adsorption and separation performance improved higher than using spirulina itself at pH from 3 to 4.5. As a result of adsorption experiment using egg white and soy bean protein, it has been found that the metal ion adsorption behavior of the spirulina blue depends on coagulative action of protein structure to some extent. However, the sharp selective adsorption performance on rare earth metal ion due to particular pH strength has been found because of actions unique to the pigment structure of phycocyanin, a major component in the spirulina blue. 7 refs., 19 figs.

  4. Syntheses, Vibrational Spectroscopy, and Crystal Structure Determination from X-Ray Powder Diffraction Data of Alkaline Earth Dicyanamides M[N(CN)

    Energy Technology Data Exchange (ETDEWEB)

    Juergens, Barbara; Irran, Elisabeth; Schnick, Wolfgang

    2001-03-01

    The alkaline earth dicyanamides Mg[N(CN){sub 2}]{sub 2}, Ca[N(CN){sub 2}]{sub 2}, Sr[N(CN){sub 2}]{sub 2}, and Ba[N(CN){sub 2}]{sub 2} were synthesized by ion exchange using Na[N(CN){sub 2}] and the respective nitrates or bromides as starting materials. The crystal structures were determined from X-ray powder diffractometry: Mg[N(CN){sub 2}]{sub 2}, Pnnm, Z=2, a=617.14(3), b=716.97(3), and c=740.35(5) pm; Ca[N(CN){sub 2}]{sub 2} and Sr[N(CN){sub 2}]{sub 2}, C2/c, Z=4; Ca[N(CN){sub 2}]{sub 2}, a=1244.55(3), b=607.97(1), and c=789.81(1) pm, {beta}=98.864(2){degree}; Sr[N(CN){sub 2}]{sub 2}, a=1279.63(2), b=624.756(8), and c=817.56(1) pm, {beta}=99.787(1){degree}; Ba[N(CN){sub 2}]{sub 2}, Pnma, Z=4, a=1368.68(7), b=429.07(7), and c=1226.26(2) pm. The dicyanamides consist of the respective alkaline earth cations and bent planar [N(CN){sub 2}]{sup -} ions. The structural features were correlated with vibrational spectroscopic data. The thermal behavior was studied by thermoanalytical experiments.

  5. Magnetic Behavior of Some Rare-Earth Transition-Metal Perovskite Oxide Systems

    Institute of Scientific and Technical Information of China (English)

    Kenji Yoshii; Akio Nakamura; Masaichiro Mizumaki; Naoshi Ikeda; Jun'ichiro Mizuki

    2004-01-01

    Magnetic properties were investigated for the rare-earth 3d-transition metal oxides with the perovskite structure. Intriguing magnetic phenomena were reviewed for a few systems:magnetization peak effect in the titanates, magnetization reversal in the chromites and metallic ferromagnetism in the cobaltites. The results suggest an important role of the rare-earth ions for the magnetic properties of such complex oxides.

  6. Evaluation of metal oxide and carbonate nanoparticle stability in soybean oil: Implications for controlled release of alkalinity during subsurface remediation

    Science.gov (United States)

    Ramsburg, C. A.; Leach, O. I.; Sebik, J.; Muller, K.

    2011-12-01

    Traditional methods for adjusting groundwater pH rely on injection of aqueous solutes and therefore, amendment distribution is reliant upon aqueous phase flow and transport. This reliance can limit mixing and sustention of amendments within the treatment zone. Oil-in-water emulsions offer an alternative for amendment delivery - one that has potential to enhance control of the distribution and release of buffering agents within the subsurface. Focus here is placed on using metal oxide and carbonate nanoparticles to release alkalinity from soybean oil, a common dispersed phase within emulsions designed to support remediation activities. Batch reactor systems were employed to examine the influence of dispersed phase composition on particle stability and solubility. The stability of uncoated MgO and CaCO3 particles in unmodified soybean oil was explored in a series of sedimentation studies conducted at solid loadings of 0.05, 0.1, and 0.2% mass. Three nominal sizes of MgO particles were examined (20, 50, and 100 nm) and one CaCO3 particle size (60 nm). Results from sedimentation studies conducted over four hours suggest that the viscosity of the soybean oil imparts a kinetic stability, for all sizes of the uncoated MgO and CaCO3 nanoparticles, which is sufficient time for particle encapsulation within oil-in-water emulsions. Based upon these results, the sedimentation of the 50 nm and 100 nm MgO, and 60 nm CaCO3 particles was assessed over longer durations (≥72 hr). Results from these stability tests suggest that the 50 nm and 100 nm MgO particles have greater kinetic stability than the 60 nm CaCO3. Batch studies were also used to assess the influence of n-butanol, a co-solvent hypothesized to aid in controlling the rate of alkalinity release, on phase behavior and metal (Mg2+ and Ca2+) solubility. Phase behavior studies suggest that n-butanol has a limited region of miscibility within the soybean oil-water system. Use of n-butanol and water within this region of

  7. Alkaline earth organometallic compounds in homogeneous catalysis : Synthesis, characterization and catalytic activity of calcium and magnesium complexes

    NARCIS (Netherlands)

    Penafiel, Johanne

    2016-01-01

    Homogeneous catalysis has been developed mainly through the use of transition metal complexes. However, transition-metal catalysts, often highly toxic, are becoming increasingly rare and consequently more expensive. Therefore, the search for sustainable alternatives is nowadays of great importance.

  8. Sequential Washing with Electrolyzed Alkaline and Acidic Water Effectively Removes Pathogens from Metal Surfaces.

    Science.gov (United States)

    Nakano, Yuichiro; Akamatsu, Norihiko; Mori, Tsuyoshi; Sano, Kazunori; Satoh, Katsuya; Nagayasu, Takeshi; Miyoshi, Yoshiaki; Sugio, Tomomi; Sakai, Hideyuki; Sakae, Eiji; Ichimiya, Kazuko; Hamada, Masahisa; Nakayama, Takehisa; Fujita, Yuhzo; Yanagihara, Katsunori; Nishida, Noriyuki

    2016-01-01

    Removal of pathogenic organisms from reprocessed surgical instruments is essential to prevent iatrogenic infections. Some bacteria can make persistent biofilms on medical devices. Contamination of non-disposable equipment with prions also represents a serious risk to surgical patients. Efficient disinfection of prions from endoscopes and other instruments such as high-resolution cameras remains problematic because these instruments do not tolerate aggressive chemical or heat treatments. Herein, we develop a new washing system that uses both the alkaline and acidic water produced by electrolysis. Electrolyzed acidic water, containing HCl and HOCl as active substances, has been reported to be an effective disinfectant. A 0.15% NaCl solution was electrolyzed and used immediately to wash bio-contaminated stainless steel model systems with alkaline water (pH 11.9) with sonication, and then with acidic water (pH 2.7) without sonication. Two bacterial species (Staphylococcus aureus and Pseudomonas aeruginosa) and a fungus (Candida albicans) were effectively removed or inactivated by the washing process. In addition, this process effectively removed or inactivated prions from the stainless steel surfaces. This washing system will be potentially useful for the disinfection of clinical devices such as neuroendoscopes because electrolyzed water is gentle to both patients and equipment and is environmentally sound.

  9. Sequential Washing with Electrolyzed Alkaline and Acidic Water Effectively Removes Pathogens from Metal Surfaces.

    Directory of Open Access Journals (Sweden)

    Yuichiro Nakano

    Full Text Available Removal of pathogenic organisms from reprocessed surgical instruments is essential to prevent iatrogenic infections. Some bacteria can make persistent biofilms on medical devices. Contamination of non-disposable equipment with prions also represents a serious risk to surgical patients. Efficient disinfection of prions from endoscopes and other instruments such as high-resolution cameras remains problematic because these instruments do not tolerate aggressive chemical or heat treatments. Herein, we develop a new washing system that uses both the alkaline and acidic water produced by electrolysis. Electrolyzed acidic water, containing HCl and HOCl as active substances, has been reported to be an effective disinfectant. A 0.15% NaCl solution was electrolyzed and used immediately to wash bio-contaminated stainless steel model systems with alkaline water (pH 11.9 with sonication, and then with acidic water (pH 2.7 without sonication. Two bacterial species (Staphylococcus aureus and Pseudomonas aeruginosa and a fungus (Candida albicans were effectively removed or inactivated by the washing process. In addition, this process effectively removed or inactivated prions from the stainless steel surfaces. This washing system will be potentially useful for the disinfection of clinical devices such as neuroendoscopes because electrolyzed water is gentle to both patients and equipment and is environmentally sound.

  10. Sequential Washing with Electrolyzed Alkaline and Acidic Water Effectively Removes Pathogens from Metal Surfaces

    Science.gov (United States)

    Nakano, Yuichiro; Akamatsu, Norihiko; Mori, Tsuyoshi; Sano, Kazunori; Satoh, Katsuya; Nagayasu, Takeshi; Miyoshi, Yoshiaki; Sugio, Tomomi; Sakai, Hideyuki; Sakae, Eiji; Ichimiya, Kazuko; Hamada, Masahisa; Nakayama, Takehisa; Fujita, Yuhzo; Yanagihara, Katsunori; Nishida, Noriyuki

    2016-01-01

    Removal of pathogenic organisms from reprocessed surgical instruments is essential to prevent iatrogenic infections. Some bacteria can make persistent biofilms on medical devices. Contamination of non-disposable equipment with prions also represents a serious risk to surgical patients. Efficient disinfection of prions from endoscopes and other instruments such as high-resolution cameras remains problematic because these instruments do not tolerate aggressive chemical or heat treatments. Herein, we develop a new washing system that uses both the alkaline and acidic water produced by electrolysis. Electrolyzed acidic water, containing HCl and HOCl as active substances, has been reported to be an effective disinfectant. A 0.15% NaCl solution was electrolyzed and used immediately to wash bio-contaminated stainless steel model systems with alkaline water (pH 11.9) with sonication, and then with acidic water (pH 2.7) without sonication. Two bacterial species (Staphylococcus aureus and Pseudomonas aeruginosa) and a fungus (Candida albicans) were effectively removed or inactivated by the washing process. In addition, this process effectively removed or inactivated prions from the stainless steel surfaces. This washing system will be potentially useful for the disinfection of clinical devices such as neuroendoscopes because electrolyzed water is gentle to both patients and equipment and is environmentally sound. PMID:27223116

  11. Solubility of ion and trace metals from stabilized sewage sludge by fly ash and alkaline mine tailing

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hongling; SUN Lina; SUN Tieheng

    2008-01-01

    Stabilized sewage sludge (SS) by fly ash (FA) and alkaline mine tailing as artificial soil,to be applied on the ecological rehabilitation at mining junkyards,offers a potentially viable utilization of the industrial by-product,as well as solves the shortage of soil resource in the mine area.An incubation experiment with different ratios of SS and FA was conducted to evaluate the solubility of ions and trace elements from stabilized sewage sludge.Results showed that fly ash offset a decrease in pH value of sewage sludge.The pH of (C) treatment (FA:SS=1:1) was stable and tended to neutrality.The SO42- and Cl- concentrations of the solution in the mixture were significantly decreased in the stabilized sewage sludge by alkaline fly ash and mine tailing,compared to the single SS treatment.Stabilized sewage sludge by FA weakened the nitrification of total nitrogen from SS when the proportion of FA in the mixture was more than 50%.The Cr,Ni,and Cu concentrations in the solution were gradually decreased and achieved a stable level after 22 days,for all treatments over the duration of the incubation.Moreover stabilized sewage sludge by fly ash and/or mine tailing notably decreased the trace metal solubility.The final Cr,Cu,and Ni concentrations in the solution for all mixtures of treatments were lower than 2.5,15,and 50 μg/L,respectively.

  12. A NEW THERMAL PROCESS FOR THE RECOVERY OF METALS FROM ZINC-CARBON AND ALKALINE SPENT BATTERIES

    Directory of Open Access Journals (Sweden)

    Girolamo Belardi

    2014-01-01

    Full Text Available The aim of this study is the thermal recovery of manganese and zinc from a mixture of zinc-carbon and alkaline spent batteries containing 40.9% of Mn and 30.1% of Zn after a preliminary physical treatment. Separation of the metals is carried out on the basis of their different phase change temperatures, the boiling point of zinc being 906�C and 1564�C that of Mn3O4, the main Mn-bearing phase in the mixture. After wet comminution and sieving to remove the anodic collectors and most of the chlorides contained in the mixture, chemical and X-Ray Powder Diffraction (XRPD analyses were performed. The mixture was heated in CO2 atmosphere and the temperature raised, thus permitting the zinc oxide to be reduced to metallic zinc by the carbon present in the original mixture. Other tests were carried out by addition to the mixture of activated charcoal (95% C or of the automotive shredder residue (fluff containing 45% C.A zinc product was obtained suitable, after refining, for the production of new batteries. The treatment residue consisted of manganese and iron oxides that could be used to produce manganese-iron alloys. From these results, an integrated process for the recovery of the two metals was proposed.

  13. A NEW THERMAL PROCESS FOR THE RECOVERY OF METALS FROM ZINC-CARBON AND ALKALINE SPENT BATTERIES

    Directory of Open Access Journals (Sweden)

    Girolamo Belardi

    2014-01-01

    Full Text Available The aim of this study is the thermal recovery of manganese and zinc from a mixture of zinc-carbon and alkaline spent batteries containing 40.9% of Mn and 30.1% of Zn after a preliminary physical treatment. Separation of the metals is carried out on the basis of their different phase change temperatures, the boiling point of zinc being 906°C and 1564°C that of Mn3O4, the main Mn-bearing phase in the mixture. After wet comminution and sieving to remove the anodic collectors and most of the chlorides contained in the mixture, chemical and X-Ray Powder Diffraction (XRPD analyses were performed. The mixture was heated in CO2 atmosphere and the temperature raised, thus permitting the zinc oxide to be reduced to metallic zinc by the carbon present in the original mixture. Other tests were carried out by addition to the mixture of activated charcoal (95% C or of the automotive shredder residue (fluff containing 45% C.A zinc product was obtained suitable, after refining, for the production of new batteries. The treatment residue consisted of manganese and iron oxides that could be used to produce manganese-iron alloys. From these results, an integrated process for the recovery of the two metals was proposed.

  14. Rare Earth Application in Sealing Anodized Al-Based Metal Matrix Composites

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A new method for corrosion protection of Al-based metal matrixcomposites (MMC) was developed using two-step process, which involves anodizing in H2SO4 solution and sealing in rare earth solution. Corrosion resistance of the treated surface was evaluated with polarization curves.The results showed that the effect of the protection using rare earth sealing is equivalent to that using chromate sealing for Al6061/SiCp. The rare earth metal salt can be an alternative to the toxic chromate for sealing anodized Al MMC.

  15. High-temperature corrosion of metals in the salt and metallic melts containing rare earths

    Science.gov (United States)

    Karpov, V. V.; Abramov, A. V.; Zhilyakov, A. Yu.; Belikov, S. V.; Volkovich, V. A.; Polovov, I. B.; Rebrin, O. I.

    2016-09-01

    A complex of independent methods was employed to study the corrosion resistance of molybdenum, zirconium, tantalum and tungsten in chloride, chloride-fluoride and fluoride-oxide melts based on LiCl, CaCl2, NaCl- KCl, LiF, and containing rare earths. Tests were conducted for 30 h at 750-1050 °C. The metals showed excellent corrosion resistance in fused chlorides (the corrosion rates were below 0.0005 g/(m2 h). Despite the presence of chemically active fluoride ions in the chloride-fluoride melts, the metals studied also showed very low corrosion rates, except molybdenum, for which the rate of corrosion was 0,8 g/(m2 h). The corrosion resistance of tantalum was considerably reduced in the fluoride-oxide melts; the corrosion rate was over 1 g/(m2 h) corresponding to the 8-th grade of stability and placing tantalum to the group of "low stability" materials.

  16. High-purity rare-earth metals: preparation, properties, and application

    Institute of Scientific and Technical Information of China (English)

    Kol'chugina; N.; B.; Burkhanov; G.; S.; Chistyakov; O.; D.; Burkhanov; Yu.; S.

    2005-01-01

    In recent years, the ever-growing interest of investigators to the study of rare-earth metals REM) is observed owing to unique properties of the metals and potential uses in electronics, laser technology, space technology, medicine, and many other high-technology applications.……

  17. High-purity rare-earth metals: preparation, properties, and application

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ In recent years, the ever-growing interest of investigators to the study of rare-earth metals REM) is observed owing to unique properties of the metals and potential uses in electronics, laser technology, space technology, medicine, and many other high-technology applications.

  18. 40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability: Description of the primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT...

  19. Comparative investigation on the effect of alkaline earth oxides on the intensity of absorption bands due to Cu2+, Mn3+ and Cr3+ ions in ternary silicate glasses

    Indian Academy of Sciences (India)

    S P Singh; Aman; Anal Tarafder

    2004-06-01

    Absorption characteristics of Cu2+, Mn3+ and Cr3+ ions in ternary silicate (20Na2O.10RO.70SiO2, where R=Ca, Sr, Ba) glasses were investigated. The intensities of absorption bands due to Cu2+ ion was found to increase with increasing ionic radii of the alkaline earth ions whereas it was found to decrease in case of Mn3+ and Cr3+ ions with increasing ionic radii of the alkaline earth ions. The results were discussed in the light of relation between linear extinction coefficients of these ions and coulombic force of alkaline earth ions. The change in intensities of Cu2+, Mn3+ and Cr3+ ion is attributed due to change in silicate glass compositions.

  20. Progress of Study on Application of Rare Earth Metals in Steels

    Institute of Scientific and Technical Information of China (English)

    Wang Longmei; Lin Qin; Ji Jingwen; Lan Denian

    2004-01-01

    With the improvement of the clean steel by degrees, the functions of rare earth metals in steel are more focused on modification of inclusions and micro alloying.The new study concerning the application of RE metals in clean steels were investigated by ICP, metallographic examination, SEM, EDS, EPMA, TEM and IMMA.The mechanism of corrosion resistance in the weather resistance steel was clarified.The mechanism of abrasion resistance and the life of fatigue enhanced in the RE - heavy rails steel were discussed.Progress in study of application of rare earth metals in steels (including weather resistance steel, low alloy steel, and heavy rails steel) was covered in this paper.

  1. Crystal Fields in Dilute Rare-Earth Metals Obtained from Magnetization Measurements on Dilute Rare-Earth Alloys

    DEFF Research Database (Denmark)

    Touborg, P.; Høg, J.

    1974-01-01

    Crystal field parameters of Tb, Dy, and Er in Sc, Y, and Lu are summarized. These parameters are obtained from magnetization measurements on dilute single crystals, and successfully checked by a number of different methods. The crystal field parameters vary unpredictably with the rare-earth solute....... B40, B60, and B66 are similar in Y and Lu. Crystal field parameters for the pure metals Tb, Dy, and Er are estimated from the crystal fields in Y and Lu....

  2. Repeated annual paper mill and alkaline residuals application affects soil metal fractions.

    Science.gov (United States)

    Gagnon, Bernard; Robichaud, Annie; Ziadi, Noura; Karam, Antoine

    2014-03-01

    The application of industrial residuals in agriculture may raise concerns about soil and crop metal accumulation. A complete study using a fractionation scheme would reveal build-up in metal pools occurring after material addition and predict the transformation of metals in soil between the different forms and potential metal release into the environment. An experimental study was conducted from 2000 to 2008 on a loamy soil at Yamachiche, Quebec, Canada, to evaluate the effects of repeated annual addition of combined paper mill biosolids when applied alone or with several liming by-products on soil Cu, Zn, and Cd fractions. Wet paper mill biosolids at 0, 30, 60, or 90 Mg ha and calcitic lime, lime mud, or wood ash, each at 3 Mg ha with 30 Mg paper mill biosolids ha, were surface applied after seeding. The soils were sampled after 6 (soybean [ (L.) Merr.]) and 9 [corn ( L.)] crop years and analyzed using the Tessier fractionation procedure. Results indicated that biosolids addition increased exchangeable Zn and Cd, carbonate-bound Cd, Fe-Mn oxide-bound Zn and Cd, organically bound Cu and Zn, and total Zn and Cd fractions but decreased Fe-Mn oxide-bound Cu in the uppermost 30-cm layer. With liming by-products, there was a shift from exchangeable to carbonate-bound forms. Even with very small metals addition, paper mill and liming materials increased the mobility of soil Zn and Cd after 9 yr of application, and this metal redistribution resulted into higher crop grain concentrations.

  3. Metal-silicate partitioning during core formation on super-Earths

    Science.gov (United States)

    Schaefer, L. K.; Jacobsen, S. B.; Petaev, M. I.; Sasselov, D. D.; Remo, J. L.

    2015-12-01

    Separation of the Earth into a rocky mantle and metallic Fe core is a problem long studied in the planetary science community (e.g. [1]). The timing of core formation influences the abundances of the siderophile elements found in the Earth's mantle, and the mechanism of core formation influences the degree of chemical equilibration between the rocky mantle and the core at the time of metal separation. However, limited work has been done on formation of metallic cores and its effects on mantle chemistry in rocky planets larger than the Earth. Super-Earths, exoplanets with masses up to ~ 5 Earth masses and radii up to ~1.6-1.7 Earth radii, have significantly larger internal pressures and consequently higher internal temperatures than the Earth, therefore conclusions from Earth-centric studies of core formation may be erroneous. Partitioning coefficients for many of the relevant elements (e.g. Fe, Ni, Si, O, etc.) are available in the literature, but only to relatively low pressures. The relevant pressures for super-Earths are significantly larger. However, data on Fe-O-Ni-Si partitioning at pressures (200-500 GPa) and temperatures relevant to super-Earths have been measured by laser-induced shocks with the ZBL laser at Sandia National Laboratory with a method described in [2]. We will present a model which integrates this data with lower pressure partition coefficients from the literature (e.g. [3],[4],[5]), with special emphasis on Fe and O, to describe partitioning behavior at high pressures and discuss its implications for core size and composition on rocky super-Earths. [1] Ringwood, A.E. (1977) Geochem. J. 11, 111-135. [2] Remo, J.L., Petaev, M.I., Jacobsen, S. B. (2008) LPSC abstract, 1420. [3] Frost, D.J. et al. (2010) JGR, B02202. [4] Kombayashi, T. (2014) JGR, 4164-4177. [5] Rubie, D.C. et al. (2011) EPSL, 301, 31-42. [5

  4. Alkaline leaching of metal melting industry wastes dseparation of zinc and lead in the leach solution

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this work, a thorough examinations on the extractability of zinc and lead present in the steelmaking dusts using alkaline leaching process and the effectiveness of the zinc and lead separation in the resultant leaching solutions using sulfide precipitation method were made. It was found that only about 53% of zinc and over 70% of the lead could be leached out of the dusts, while the other 47% of zinc and 306 of lead were left in the leaching residues. The zinc and lead in the resultant leaching solution can be effectively and selectively separated. When the weight ratio of sodium sulfide (M. W. = 222-240) to Pb was kept at 1.8, the lead in the solution could be precipitated out quantitatively while all the zinc was remained in the solution. The zinc left in the solution can be further recovered by the addition of extra sodium sulfide with a weight ratio of sodium sulfide to the zinc over 2.6. The resultant filtrate can be recycled to the leaching of dust in the next leaching process.

  5. Dispersion coefficients for the interactions of the alkali and alkaline-earth ions and inert gas atoms with a graphene layer

    CERN Document Server

    Kaur, Kiranpreet; Sahoo, B K

    2015-01-01

    Largely motivated by a number of applications, the van der Waals dispersion coefficients ($C_3$s) of the alkali ions (Li$^+$, Na$^+$, K$^+$ and Rb$^+$), the alkaline-earth ions (Ca$^+$, Sr$^+$, Ba$^+$ and Ra$^+$) and the inert gas atoms (He, Ne, Ar and Kr) with a graphene layer are determined precisely within the framework of Dirac model. For these calculations, we have evaluated the dynamic polarizabilities of the above atomic systems very accurately by evaluating the transition matrix elements employing relativistic many-body methods and using the experimental values of the excitation energies. The dispersion coefficients are, finally, given as functions of the separation distance of an atomic system from the graphene layer and the ambiance temperature during the interactions. For easy extraction of these coefficients, we give a logistic fit to the functional forms of the dispersion coefficients in terms of the separation distances at the room temperature.

  6. Chemoselective single-site Earth-abundant metal catalysts at metal–organic framework nodes

    Energy Technology Data Exchange (ETDEWEB)

    Manna, Kuntal; Ji, Pengfei; Lin, Zekai; Greene, Francis X.; Urban, Ania; Thacker, Nathan C.; Lin, Wenbin (UC)

    2016-08-30

    Earth-abundant metal catalysts are critically needed for sustainable chemical synthesis. Here we report a simple, cheap and effective strategy of producing novel earth-abundant metal catalysts at metal–organic framework (MOF) nodes for broad-scope organic transformations. The straightforward metalation of MOF secondary building units (SBUs) with cobalt and iron salts affords highly active and reusable single-site solid catalysts for a range of organic reactions, including chemoselective borylation, silylation and amination of benzylic C–H bonds, as well as hydrogenation and hydroboration of alkenes and ketones. Our structural, spectroscopic and kinetic studies suggest that chemoselective organic transformations occur on site-isolated, electron-deficient and coordinatively unsaturated metal centres at the SBUs via σ-bond metathesis pathways and as a result of the steric environment around the catalytic site. MOFs thus provide a novel platform for the development of highly active and affordable base metal catalysts for the sustainable synthesis of fine chemicals.

  7. Environmental Defects And Economic Impact On Global Market Of Rare Earth Metals

    Science.gov (United States)

    Charalampides, G.; Vatalis, K.; Karayannis, V.; Baklavaridis, A.

    2016-11-01

    Rare earth elements include the 14 lanthanides as well as lanthanium and often yttrium. Actually, most of them are not very rare and occur widely dispersed in a variety of rocks. Rare earth metals are vital to some of the world's faster growing industries: catalysts, Nd-magnets, ceramics, glass, metallurgy, battery alloys, electronics and phosphors. Worldwide, the main countries for distribution of rare earths deposits include China, USA, Russia, Brasil, India, Australia, Greenland and Malaysia. The mining and processing of rare earth metals usually result in significant environmental defects. Many deposits are associated with high concentrations of radioactive elements such as uranium and thorium, which requires separate treatment and disposal. The accumulation of rare earth elements in soils has occurred due to pollution caused by the exploitation of rare earth resources and the wide use of rare earths as fertilizers in agriculture. This accumulation has a toxic effect on the soil microfauna community. However, there are large differences in market prices due to the degree of purity determined by the specifications in the applications. The main focus of this article is to overview Rare Earth Metals’ overall impact on global economy and their environmental defects on soils during processing techniques and as they are used as fertilizers.

  8. Theoretical studies of the spin Hamiltonian parameters and local distortions for Cu{sup 2+} in alkaline earth lead zinc phosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Bo-Kun; Yuan, Zi-Yi; Liu, Zi-Xuan; Jiang, Shi-Xin; Liu, Zheng; Yao, Zi-Jian [University of Electronic Science and Technology of China, Chengdu (China). School of Yingcai Honors; Wu, Shao-Yi; Teng, Bao-Hua; Wu, Ming-He [University of Electronic Science and Technology of China, Chengdu (China). Dept. of Applied Physics

    2016-11-01

    The spin Hamiltonian parameters and local structures are theoretically studied for Cu{sup 2+}-doped alkaline earth lead zinc phosphate (RPPZ, R=Mg, Ca, Sr, and Ba) glasses based on the high-order perturbation calculations for a tetragonally elongated octahedral 3d{sup 9} cluster. The relative elongation ratios are found to be ρ ∼ 3.2%, 4.4%, 4.6%, and 3.3% for R=Mg, Ca, Sr, and Ba, respectively, because of the Jahn-Teller effect. The whole decreasing crystal-field strength Dq and orbital reduction factor k from Mg to Sr are ascribed to the weakening electrostatic coulombic interactions and the increasing probability of productivity of nonbridge oxygen (and hence increasing Cu{sup 2+}-O{sup 2-} electron cloud admixtures) under PbO addition, respectively, with increasing alkali earth ionic radius. The anomalies (the largest Dq and the next highest k among the systems) for R=Ba are attributed to the cross linkage of this large cation in the network. The overall increasing order (Mg≤Ba

  9. Structure of Some 4f Rare Earth Liquid Metals - A Charged Hard Sphere Approach

    Institute of Scientific and Technical Information of China (English)

    P.B. Thakor; P.N. Gajjar; A.R. Jani

    2006-01-01

    A well-established pseodopotential is used to study the structure of some 4f rare earth liquid metals (Ce,Pr, Eu, Gd, Tb, and Yb). The structure factor S(q), pair distribution function g(r), interatomic distance r1, and coordination number n1 are calculated using Charged Hard Sphere (CHS) reference system. To introduce the exchange and correlation effects, the local field correction due to Sarkar et al. (S) is applied. The present investigation is successful in generating the structural information of Ce, Pr, Eu, Gd, Tb, and Yb 4f rare earth liquid metals.

  10. Inference on the Nature and the Mass of Earth's Late Veneer from Noble Metals and Gases

    CERN Document Server

    Dauphas, N

    2001-01-01

    Noble metals and gases are very sensitive to the late accretion to the Earth of asteroids and comets. We present mass balance arguments based on these elements that indicate that 0.7E22-2.7E22 kg of extraterrestrial bodies struck the Earth after core formation and that comets comprised less than 1E-5 by mass of the impacting population. These results imply that the dynamics of asteroids and comets changed drastically with time and that biogenic elements and prebiotic molecules were not delivered to the Earth by comets but rather by carbonaceous asteroids.

  11. Nickel based alloys as electrocatalysts for oxygen evolution from alkaline solutions. [Metal--air batteries

    Energy Technology Data Exchange (ETDEWEB)

    Lu, P.W.T.; Srinivasan, S.

    1977-01-01

    The slowness of the oxygen evolution reaction is one of the main reasons for significant energy losses in water electrolysis cells and secondary air--metal batteries. To date, data on the kinetics of this reaction on alloys and intermetallic compounds are sparse. In this work, mechanically polished alloys of nickel with Ir, Ru or W and Ni--Ti intermetallic compounds were studied as oxygen electrodes. Since the oxygen evolution reaction always takes place on oxide-film covered surfaces, the nature of oxide films formed on these alloys were investigated using cyclic voltametric techniques. Steady-state potentiostatic and slow potentiodynamic (at 0.1 mV/s) methods were employed to obtain the electrode kinetic parameters for the oxygen evolution reaction in 30 wt. percent KOH at 80/sup 0/C, the conditions normally used in water electrolysis cells. The peaks for the formation or reduction of oxygen-containing layers appearing on the pure metals are not always found on the alloys. The maximum decreases in oxygen overpotential at an apparent current density of 20 mA cm/sup -2/ (as compared with that on Ni) were found for the alloys of 50Ni--50Ir and 75Ni--25Ru and the intermetallic compound Ni/sub 3/Ti, these decreases being about 40, 30, and 20 mV, respectively. On the long-term polarization in the potential region of oxygen evolution, the oxygen-containing layers on Ni--Ir or Ni--Ru alloys are essentially composed of nickel oxides instead of true mixed oxide films of two components. The present work confirms that, possibly because of coverage by oxide films, there is no direct dependence of the electrocatalytic activities of the alloys on their electronic properties. 11 figures, 1 table.

  12. Eu(2+)-Activated Alkaline-Earth Halophosphates, M5(PO4)3X:Eu(2+) (M = Ca, Sr, Ba; X = F, Cl, Br) for NUV-LEDs: Site-Selective Crystal Field Effect.

    Science.gov (United States)

    Kim, Donghyeon; Kim, Sung-Chul; Bae, Jong-Seong; Kim, Sungyun; Kim, Seung-Joo; Park, Jung-Chul

    2016-09-06

    Eu(2+)-activated M5(PO4)3X (M = Ca, Sr, Ba; X = F, Cl, Br) compounds providing different alkaline-earth metal and halide ions were successfully synthesized and characterized. The emission peak maxima of the M5(PO4)3Cl:Eu(2+) (M = Ca, Sr, Ba) compounds were blue-shifted from Ca to Ba (454 nm for Ca, 444 nm for Sr, and 434 nm for Ba), and those of the Sr5(PO4)3X:Eu(2+) (X = F, Cl, Br) compounds were red-shifted along the series of halides, F → Cl → Br (437 nm for F, 444 nm for Cl, and 448 nm for Br). The site selectivity and occupancy of the activator ions (Eu(2+)) in the M5(PO4)3X:Eu(2+) (M = Ca, Sr, Ba; X = F, Cl, Br) crystal lattices were estimated based on theoretical calculation of the 5d → 4f transition energies of Eu(2+) using LCAO. In combination with the photoluminescence measurements and theoretical calculation, it was elucidated that the Eu(2+) ions preferably enter the fully oxygen-coordinated sites in the M5(PO4)3X:Eu(2+) (M = Ca, Sr, Ba; X = F, Cl, Br) compounds. This trend can be well explained by "Pauling's rules". These compounds may provide a platform for modeling a new phosphor and application in the solid-state lighting field.

  13. Effect of Ca{sup 2+} and Sr{sup 2+} alkaline earth ions on luminescence properties of BaAl{sub 12}O{sub 19}:Eu nanophosphor

    Energy Technology Data Exchange (ETDEWEB)

    Deshmukh, Abhay D., E-mail: abhay_d1984@yahoo.co.i [National Environmental Engineering Research Institute, Nagpur 440020 (India); Department of Metallurgical and Materials Engineering, VNIT, Nagpur 440011 (India); Valechha, Arti; Valechha, Dolly; Kumar, Animesh [National Environmental Engineering Research Institute, Nagpur 440020 (India); Peshwe, D.R. [Department of Metallurgical and Materials Engineering, VNIT, Nagpur 440011 (India); Dhoble, S.J. [Kamla Nehru College, Sakkardara Square, Nagpur 440009 (India)

    2009-07-15

    Nanosized barium aluminate materials was doped by divalent cations (Ca{sup 2+}, Sr{sup 2+}) and Eu{sup 2+} having nominal compositions Ba{sub 1-x}MxAl{sub 12}O{sub 19}:Eu (M=Ca and Sr) (x=0.1-0.5), were synthesized by the combustion method. These phosphors were characterized by XRD, scanning electron microscopy-energy-dispersive spectrometry (SEM-EDS) and photoluminescence measurement. The photoluminescence characterization showed the presence of Eu ion in divalent form which gave emission bands peaking at 444 nm for the 320 nm excitation (solid-state lighting excitation), while for 254 nm it gave the same emission wavelength of low intensity (1.5 times) compared to 320 nm excitation. It was also observed that alkaline earth metal (Ca{sup 2+} and Sr{sup 2+}) dopants increase the intensity of Eu{sup 2+} ion in BaAl{sub 12}O{sub 19} lattice, thus this phosphor may be useful for solid-state lighting.

  14. New technology of extracting the amount of rare earth metals from the red mud

    Science.gov (United States)

    Martoyan, G. A.; Karamyan, G. G.; Vardan, G. A.

    2016-01-01

    The paper outlined the environmental and economic problems associated with red mud - the waste generated in processing of bauxite ore for aluminum production. The chemical analysis of red mud has identified a number of useful elements including rare earth metals. The electromembrane technology of red mud processing with extraction of valuable elements is described. A possible scheme of separation of these metals through electrolysis is also given.

  15. Influence of monovalent alkaline metal cations on binder-free nano-zeolite X in para-xylene separation

    Institute of Scientific and Technical Information of China (English)

    Milad Rasouli; Nakisa Yaghobi; Hossein Atashi; Majid Rasouli

    2015-01-01

    The adsorption process was studied for separating para-xylene from xylene mixture on modified nano-zeolite X in a breakthrough system. Nano-zeolitic adsorbent with different ratios of SiO2/Al2O3 was synthesized through hydrothermal process and ion-exchanged with alkaline metal cations like lithium, sodium and potassium. The product was characterized by X-ray diffraction, scanning electron microscopy (SEM), nitrogen adsorption, transform electron microscopy (TEM) and in situ Fourier transform infrared (FTIR) spectroscopy. The influence of nano-zeolite water content and desorbent type on the selectivity of para-xylene toward other C8 aromatic isomers was studied. The optimization of adsorption process was also investigated under variable operation conditions. The isotherm for each isomer of C8 aromatics and the desorbents possess the adsorption characteristics of Langmuir type. The selectivity factor of para-xylene relative to each of meta-xylene, ortho-xylene and ethylben-zene under the optimum conditions obtained to be 5.36, 2.43 and 3.22, in the order given.

  16. Graphene-based non-noble-metal Co/N/C catalyst for oxygen reduction reaction in alkaline solution

    Science.gov (United States)

    Niu, Kexing; Yang, Baoping; Cui, Jinfeng; Jin, Jutao; Fu, Xiaogang; Zhao, Qiuping; Zhang, Junyan

    2013-12-01

    This study develops a promising catalyst for oxygen reduction reaction (ORR) via a simple two-step heat treatment of a mixture of cobalt(II) nitrate hexahydrate (Co(NO3)2·6H2O), polyethyleneimine (PEI), and graphene oxide (GO), firstly in argon atmosphere and then in ammonia atmosphere. X-ray photoemission spectroscopy (XPS) result reveals that the catalyst has pyridinic N-dominant (46% atomic concentration among all N components) on the surface. The kinetics measurement of the catalyst in 0.1 M KOH solution using a rotating disk electrode (RDE) reveals that the catalyst (Co/N/rGO(NH3)) has high activity. Furthermore, the number of electrons exchanged during the ORR with the catalyst is determined to be ˜3.9, suggesting that the ORR is dominated by a 4e- reduction of O2 to H2O. The catalyst has good stability, and its performance is superior to the commercial Pt/C(20%) catalyst in alkaline condition, making the material a promising substitute to noble metal ORR electrocatalyst on the cathode side of fuel cells.

  17. Simultaneous production of alkaline lipase and protease by antibiotic and heavy metal tolerant Pseudomonas aeruginosa.

    Science.gov (United States)

    Bisht, Deepali; Yadav, Santosh Kumar; Gautam, Pallavi; Darmwal, Nandan Singh

    2013-09-01

    An efficient bacterial strain capable of simultaneous production of lipase and protease in a single production medium was isolated. Thirty six bacterial strains, isolated from diverse habitats, were screened for their lipolytic and proteolytic activity. Of these, only one bacterial strain was found to be lipase and protease producer. The 16S rDNA sequencing and phylogenetic analyses revealed that strain (NSD-09) was in close identity to Pseudomonas aeruginosa. The maximum lipase (221.4 U/ml) and protease (187.9 U/ml) activities were obtained after 28 and 24 h of incubation, respectively at pH 9.0 and 37 °C. Castor oil and wheat bran were found to be the best substrate for lipase and protease production, respectively. The strain also exhibited high tolerance to lead (1450 µg/ml) and chromium (1000 µg/ml) in agar plates. It also showed tolerance to other heavy metals, such as Co(+2) , Zn(+2) , Hg(+2) , Ni(+2) and Cd(+2) . Therefore, this strain has scope for tailing bioremediation. Presumably, this is the first attempt on P. aeruginosa to explore its potential for both industrial and environmental applications.

  18. Lack of marked cyto- and genotoxicity of cristobalite in devitrified (heated) alkaline earth silicate wools in short-term assays with cultured primary rat alveolar macrophages.

    Science.gov (United States)

    Ziemann, Christina; Harrison, Paul T C; Bellmann, Bernd; Brown, Robert C; Zoitos, Bruce K; Class, Philippe

    2014-02-01

    Alkaline earth silicate (AES) wools are low-biopersistence high-temperature insulation wools. Following prolonged periods at high temperatures they may devitrify, producing crystalline silica (CS) polymorphs, including cristobalite, classified as carcinogenic to humans. Here we investigated the cytotoxic and genotoxic significance of cristobalite present in heated AES wools. Primary rat alveolar macrophages were incubated in vitro for 2 h with 200 µg/cm² unheated/heated calcium magnesium silicate wools (CMS1, CMS2, CMS3; heat-treated for 1 week at, or 4 weeks 150 °C below, their respective classification temperatures) or magnesium silicate wool (MS; heated for 24 h at 1260 °C). Types and quantities of CS formed, and fiber size distribution and shape were determined by X-ray diffraction and electron microscopy. Lactate dehydrogenase release and alkaline and hOGG1-modified comet assays were used, ± aluminum lactate (known to quench CS effects), for cytotoxicity/genotoxicity screening. Cristobalite content of wools increased with heating temperature and duration, paralleled by decreases in fiber length and changes in fiber shape. No marked cytotoxicity, and nearly no (CMS) or only slight (MS) DNA-strand break induction was observed, compared to the CS-negative control Al₂O₃, whereas DQ12 as CS-positive control was highly active. Some samples induced slight oxidative DNA damage, but no biological endpoint significantly correlated with free CS, quartz, or cristobalite. In conclusion, heating of AES wools mediates changes in CS content and fiber length/shape. While changes in fiber morphology can impact biological activity, cristobalite content appears minor or of no relevance to the intrinsic toxicity of heated AES wools in short-term assays with rat alveolar macrophages.

  19. High-Field Magnetization of Light Rare-Earth Metals

    DEFF Research Database (Denmark)

    McEwen, K.A.; Cock, G.J.; Roeland, L.W.;

    1973-01-01

    The magnetization of single crystals of Eu, Sm, Nd, Pr, and Pr-Nd alloys has been measured in fields up to 37 T (370 kG). The results give new information on the magnetic properties of these metals. Of particular interest is a first-order transition from a nonmagnetic to a metamagnetic phase...... in double-hexagonal close-packed Pr, due to the crossing of crystal-field levels, when a field of about 32 T is applied in the hard direction at low temperatures....

  20. On the single-ion Magnetic Anisotropy of the Rare-Earth Metals

    DEFF Research Database (Denmark)

    Kolmakova, N.P.; Tishin, A.M.; Bohr, Jakob

    1996-01-01

    The temperature dependences of the single-ion magnetic anisotropy constants for Tb and Dy metals are calculated in terms of the multipole moments of the rare-earth ions utilizing the available crystal-field parameters. The results are compared with the existing experimental data....

  1. A field study on heavy metals phytoattenuation potential of monocropping and intercropping of maize and/or legumes in weakly alkaline soils.

    Science.gov (United States)

    Zhu, Saiyong; Ma, Xinwang; Guo, Rui; Ai, Shiwei; Liu, Bailin; Zhang, Wenya; Zhang, Yingmei

    2016-10-02

    The study focused on the phytoattenuation effects of monocropping and intercropping of maize (Zea mays) and/or legumes on Cu, Zn, Pb, and Cd in weakly alkaline soils. Nine growth stages of monocropping maize were chosen to study the dynamic process of extraction of heavy metals. The total content of heavy metals extracted by the aerial part of monocropped maize increased in a sigmoidal pattern over the effective accumulative temperature. The biggest biomass, highest extraction content, and lowest heavy metals bioaccumulation level occurred at physiological maturity. Among the different planting patterns, including monocropping and intercropping of maize and/or soybean (Glycine max), pea (Pisum sativum), and alfalfa (Medicago sativa), the extraction efficiency of Cu, Zn, Pb, and Cd varied greatly. Only intercropping of maize and soybean yielded relatively higher extraction efficiency for the four metals with no significant difference in the total biomass. Moreover, the heavy metals concentrations in dry biomass from all the planting patterns in the present study were within China's national legal thresholds for fodder use. Therefore, slightly polluted alkaline soils can be safely used through monocropping and intercropping of maize and/or legumes for a range of purposes. In particular, this study indicated that intercropping improves soil ecosystems polluted by heavy metals compared with monocropping.

  2. Effect of Rare Earth Metals on the Microstructure of Al-Si Based Alloys

    Directory of Open Access Journals (Sweden)

    Saleh A. Alkahtani

    2016-01-01

    Full Text Available The present study was performed on A356 alloy [Al-7 wt %Si 0.0.35 wt %Mg]. To that La and Ce were added individually or combined up to 1.5 wt % each. The results show that these rare earth elements affect only the alloy melting temperature with no marked change in the temperature of Al-Si eutectic precipitation. Additionally, rare earth metals have no modification effect up to 1.5 wt %. In addition, La and Ce tend to react with Sr leading to modification degradation. In order to achieve noticeable modification of eutectic Si particles, the concentration of rare earth metals should exceed 1.5 wt %, which simultaneously results in the precipitation of a fairly large volume fraction of insoluble intermetallics. The precipitation of these complex intermetallics is expected to have a negative effect on the alloy performance.

  3. PERVAPORATION SEPARATION OF WATER-ACETIC ACID MIXTURES THROUGH AN-co-AA MEMBRANES TREATED WITH RARE EARTH METAL IONS

    Institute of Scientific and Technical Information of China (English)

    SHEN Zhiquan; ZHANG Fuyao; ZHANG Yifeng

    1995-01-01

    Pervaporation separation of water-acetic acid mixtures through Poly (AN-co-AA)membranes and rare earth metal ions treated Poly(AN-co-AA)membranes was investigated for the first time. The results showed that the treatment with rare earth metal ions could greatly improve the characteristics of the separation of water-acetic acid mixtures.

  4. Electronic and Magnetic Properties of Rare-Earth Metals Doped ZnO Monolayer

    Directory of Open Access Journals (Sweden)

    Changlong Tan

    2015-01-01

    Full Text Available The structural, electronic, and magnetic properties of rare-earth metals doped ZnO monolayer have been investigated using the first-principles calculations. The induced spin polarization is confirmed for Ce, Eu, Gd, and Dy dopings while the induced spin polarization is negligible for Y doping. The localized f states of rare-earth atoms respond to the introduction of a magnetic moment. ZnO monolayer undergoes transition from semiconductor to metal in the presence of Y, Ce, Gd, and Dy doping. More interestingly, Eu doped ZnO monolayer exhibits half-metallic behavior. Our result demonstrates that the RE-doping is an efficient route to modify the magnetic and electronic properties in ZnO monolayer.

  5. Influence of Ce, Nd, Sm and Gd oxides on the properties of alkaline-earth borosilicate glass sealant

    Directory of Open Access Journals (Sweden)

    Nibedita Sasmal

    2016-03-01

    Full Text Available In this study, the influence of CeO2, Nd2O3, Sm2O3 and Gd2O3 on various properties of the melt-quench route derived SrO–CaO–ZnO–B2O3–SiO2 glass have been investigated. Both the precursor glasses and heat treated glasses are characterized by dilatometry, differential scanning calorimetry (DSC, X-ray diffraction (XRD, field emission scanning electron microscopy (FESEM, Fourier transformed infrared spectroscopy (FTIR and X-ray photoelectron spectroscopy (XPS. The density and coefficient of thermal expansion of the glasses varies in the range 3.557–3.804 g cm−3 and 10.5–11.2 × 10−6 K−1 (50–800 °C respectively. Decrease in crystallization tendency with increase in cationic field strength of the ions is well supported by the increasing crystallization activation energy of the glasses calculated by Kissinger, Augis–Bennett and Ozawa models. XPS study revealed the presence of both Ce3+ and Ce4+ ions and an increase in characteristic binding energy of the respective rare earth elements from their core level studies. The Knoop hardness of the glasses varies in the range 6.03–6.28 GPa. The glass transition, glass softening and crystallization temperature; density and hardness of the glasses increased with increase in cationic field strength of the incorporated ions. The thermomechanical properties of the Gd2O3 containing glass advocate its applicability as the most promising sealant in solid oxide fuel cell.

  6. [High current microsecond pulsed hollow cathode lamp excited ionic fluorescence spectrometry of alkaline earth elements in inductively coupled plasma with a Fassel-torch].

    Science.gov (United States)

    Zhang, Shao-Yu; Gong, Zhen-Bin; Huang, Ben-Li

    2006-02-01

    High current microsecond pulsed hollow cathode lamp (HCMP-HCL) excited ionic fluorescence spectrometry (IFS) of alkaline earth elements in inductively coupled plasma (ICP) with a Fassel-torch has been investigated. In wide condition ranges only IFS was observed, whilst atomic fluorescence spectrometry (AFS) was not detectable. More intense ionic fluorescence signal was observed at lower observation heights and at lower incident RF powers. Without introduction of any reduction organic gases into the ICP, the limit of detection (LOD, 3sigma) of Ba was improved by 50-fold over that of a conventional pulsed (CP) HCL with the Baird sleeve-extended torch. For Ca and Sr, the LODs by HCMP-HCL-ICP-IFS and CP-HCL-ICP-AFS show no significant difference. Relative standard deviations were 0.6%-1.4% (0.1-0.2 microg x mL(-1), n = 10) for 5 ionic fluorescence lines. Preliminary studies showed that the intensity of ionic fluorescence could be depressed in the presence of K, Al and P.

  7. The long-range non-additive three-body dispersion interactions for the rare gases, alkali, and alkaline-earth atoms.

    Science.gov (United States)

    Tang, Li-Yan; Yan, Zong-Chao; Shi, Ting-Yun; Babb, James F; Mitroy, J

    2012-03-14

    The long-range non-additive three-body dispersion interaction coefficients Z(111), Z(112), Z(113), and Z(122) are computed for many atomic combinations using standard expressions. The atoms considered include hydrogen, the rare gases, the alkali atoms (up to Rb), and the alkaline-earth atoms (up to Sr). The term Z(111) arising from three mutual dipole interactions is known as the Axilrod-Teller-Muto coefficient or the DDD (dipole-dipole-dipole) coefficient. Similarly, the terms Z(112), Z(113), and Z(122) arise from the mutual combinations of dipole (1), quadrupole (2), and octupole (3) interactions between atoms and they are sometimes known, respectively, as dipole-dipole-quadrupole, dipole-dipole-octupole, and dipole-quadrupole-quadrupole coefficients. Results for the four Z coefficients are given for the homonuclear trimers, for the trimers involving two like-rare-gas atoms, and for the trimers with all combinations of the H, He, and Li atoms. An exhaustive compilation of all coefficients between all possible atomic combinations is presented as supplementary data.

  8. Transfer of alkaline earth elements in mothers' milk and doses from {sup 45}Ca, {sup 90}Sr and {sup 226}Ra

    Energy Technology Data Exchange (ETDEWEB)

    Smith, T.J.; Phipps, A.W.; Fell, T.P.; Harrison, J.D

    2003-07-01

    An international programme of work is currently under way to develop methods for calculating doses to infants from ingestion of radionuclides present in mothers' milk. This paper considers the special case of the alkaline earth elements. Models have been developed for {sup 45}Ca, {sup 90}Sr and {sup 226}Ra and the sensitivity of results to various changes in parameter values is discussed. A complication when calculating doses from intakes of radium is that the International Commission on Radiological Protection has previously recommended that doses from decay products of radium should be calculated using element-specific biokinetic models (so-called independent biokinetics). An extension of this method to the models for breastfeeding is proposed. Preliminary estimates of the doses received by the infant for a number of maternal intake scenarios show that doses to the infant can exceed the corresponding adult dose, such as for {sup 45}Ca (ratio = 3.1) while, in other cases such as {sup 90}Sr, the infant dose can be a significant fraction of the adult dose. (author)

  9. The long-range non-additive three-body dispersion interactions for the rare gases, alkali and alkaline-earth atoms

    CERN Document Server

    Tang, Li-Yan; Shi, Ting-Yun; Babb, James F; Mitroy, J

    2012-01-01

    The long-range non-additive three-body dispersion interaction coefficients $Z_{111}$, $Z_{112}$, $Z_{113}$, and $Z_{122}$ are computed for many atomic combinations using standard expressions. The atoms considered include hydrogen, the rare gases, the alkali atoms (up to Rb) and the alkaline-earth atoms (up to Sr). The term $Z_{111}$, arising from three mutual dipole interactions is known as the Axilrod-Teller-Muto coefficient or the DDD (dipole-dipole-dipole) coefficient. Similarly, the terms $Z_{112}$, $Z_{113}$, and $Z_{122}$ arise from the mutual combinations of dipole (1), quadrupole (2), and octupole (3) interactions between atoms and they are sometimes known, respectively, as DDQ, DDO, and DQQ coefficients. Results for the four $Z$ coefficients are given for the homonuclear trimers, for the trimers involving two like-rare-gas atoms, and for the trimers with all combinations of the H, He, Li atoms. An exhaustive compilation of all coefficients between all possible atomic combinations is presented as supp...

  10. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system.

    Science.gov (United States)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

    2013-06-15

    The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid-liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system.

  11. Interaction of an aluminum atom with an alkaline earth atom: Spectroscopic and ab initio investigations of AlCa

    Science.gov (United States)

    Behm, Jane M.; Morse, Michael D.; Boldyrev, Alexander I.; Simons, Jack

    1994-10-01

    A spectroscopic analysis of diatomic AlCa generated by laser vaporization of a 2:1 Al:Ca metal alloy followed by supersonic expansion has been completed using resonant two-photon ionization spectroscopy. Four excited electronic states have been identified and investigated in the energy region from 13 500 to 17 900 cm-1. These are the [13.5] 2Πr, the [15.8] 2Σ, the [17.0] 2Δ3/2(?), and the [17.6] 2Δ3/2 states. From rotational analysis excited state bond lengths have been measured for three of the four excited states, and the ground state has been unambiguously determined as a 2Πr state with a weighted least squares value of the ground state bond length of r0` = 3.1479± 0.0010 Å. The ionization energy of the molecule has also been directly determined as 5.072±0.028 eV. Ab initio calculations for the potential energy curves of seven low-lying states of AlCa [X 2Πr, 2Σ+, 4Σ-, 4Πr, 2Πr(2), 2Δ, and 2Σ-] and for the X 1Σ+ ground electronic state of AlCa+ have been carried out. In agreement with experiment, 2Πr is calculated to be the ground electronic state of the neutral molecule. The dissociation energies of AlCa (X 2Πr) into Al(3s23p1,2P0)+Ca(4s2,1S) and for AlCa+ (X 1Σ+) into Al+(3s2,1S)+Ca(4s2,1S) are calculated to be 0.47 and 1.50 eV, respectively. The excited 2Σ+, 4Σ-, 4Πr, 2Πr(2), 2Δ, and 2Σ- states are calculated to lie 0.2, 0.7, 0.7, 1.1, 1.1, and 1.1 eV above X 2Πr, respectively, and the vertical and adiabatic ionization energies of AlCa have been calculated to be 5.03 and 4.97 eV, respectively.

  12. Rare earth element recycling from waste nickel-metal hydride batteries.

    Science.gov (United States)

    Yang, Xiuli; Zhang, Junwei; Fang, Xihui

    2014-08-30

    With an increase in number of waste nickel-metal hydride batteries, and because of the importance of rare earth elements, the recycling of rare earth elements is becoming increasingly important. In this paper, we investigate the effects of temperature, hydrochloric acid concentration, and leaching time to optimize leaching conditions and determine leach kinetics. The results indicate that an increase in temperature, hydrochloric acid concentration, and leaching time enhance the leaching rate of rare earth elements. A maximum rare earth elements recovery of 95.16% was achieved at optimal leaching conditions of 70°C, solid/liquid ratio of 1:10, 20% hydrochloric acid concentration, -74μm particle size, and 100min leaching time. The experimental data were best fitted by a chemical reaction-controlled model. The activation energy was 43.98kJ/mol and the reaction order for hydrochloric acid concentration was 0.64. The kinetic equation for the leaching process was found to be: 1-(1-x)(1/3)=A/ρr0[HCl](0.64)exp-439,8008.314Tt. After leaching and filtration, by adding saturated oxalic solution to the filtrate, rare earth element oxalates were obtained. After removing impurities by adding ammonia, filtering, washing with dilute hydrochloric acid, and calcining at 810°C, a final product of 99% pure rare earth oxides was obtained.

  13. Chemoselective single-site Earth-abundant metal catalysts at metal–organic framework nodes

    Science.gov (United States)

    Manna, Kuntal; Ji, Pengfei; Lin, Zekai; Greene, Francis X.; Urban, Ania; Thacker, Nathan C.; Lin, Wenbin

    2016-01-01

    Earth-abundant metal catalysts are critically needed for sustainable chemical synthesis. Here we report a simple, cheap and effective strategy of producing novel earth-abundant metal catalysts at metal–organic framework (MOF) nodes for broad-scope organic transformations. The straightforward metalation of MOF secondary building units (SBUs) with cobalt and iron salts affords highly active and reusable single-site solid catalysts for a range of organic reactions, including chemoselective borylation, silylation and amination of benzylic C–H bonds, as well as hydrogenation and hydroboration of alkenes and ketones. Our structural, spectroscopic and kinetic studies suggest that chemoselective organic transformations occur on site-isolated, electron-deficient and coordinatively unsaturated metal centres at the SBUs via σ-bond metathesis pathways and as a result of the steric environment around the catalytic site. MOFs thus provide a novel platform for the development of highly active and affordable base metal catalysts for the sustainable synthesis of fine chemicals. PMID:27574182

  14. Distribution of Rare Earth Metals in Technogenic Wastes of Energy Enterprises (Results of the Laboratory Studies)

    OpenAIRE

    Alexandr Ivanovich Khanchuk; Aleksandr Alekseevich Yudakov; Mikhail Azaryevich Medkov; Leonid Nikolayevich Alekseyko; Andrey Vasilyevich Taskin; Sergey Igorevich Ivannikov

    2016-01-01

    The results of the research interaction between ash and slag samples from Vladivostok TPP’s landfills saturated with underburning and ammonium hydrodifluoride were given. It was found out that the reactions of the main components of a concentrate with NH4HF2 are flowing with creation of complex ammonium fluoro-metalate. It is shown that the distribution of REM (rare earth metals) between foam and heavier products is going during the flotation process of carbon-containing ash and slag samples ...

  15. Distribution of Rare Earth Metals in Technogenic Wastes of Energy Enterprises (Results of the Laboratory Studies

    Directory of Open Access Journals (Sweden)

    Alexandr Ivanovich Khanchuk

    2016-12-01

    Full Text Available The results of the research interaction between ash and slag samples from Vladivostok TPP’s landfills saturated with underburning and ammonium hydrodifluoride were given. It was found out that the reactions of the main components of a concentrate with NH4HF2 are flowing with creation of complex ammonium fluoro-metalate. It is shown that the distribution of REM (rare earth metals between foam and heavier products is going during the flotation process of carbon-containing ash and slag samples without significant concentrating. It is shown that the water leaching of fluoridated product lets transfer silicone, aluminum and iron salts into solution and concentrate rare earth elements in insoluble residue in the form of complex salts of NaLnF4 general formula. We propose a schematic diagram of hydrodifluoride recycling of carbon-containing sample, which provides concentrating of REM with incomplete separation of macro-components.

  16. Thermal oxidation of the surface of binary aluminum alloys with rare-earth metals

    Science.gov (United States)

    Akashev, L. A.; Popov, N. A.; Kuznetsov, M. V.; Shevchenko, V. G.

    2015-05-01

    The kinetics of oxidation of the surface of Al alloys with 1-2.5 at % rare-earth metals (REMs) at 400-500°C in air was studied by ellipsometry and X-ray photoelectron spectroscopy (XPS). The addition (1-2.5 at % REM) of all rare-earth metals to aluminum was shown to increase the thickness of the oxide layer. The addition of surfactant and chemically active REMs (Yb, Sm, La, and Ce) increased the rate of oxidation of solid aluminum most effectively. The oxidation can be accelerated by the polymorphic transformations of the individual REM oxides in the film. The surface activity of Sm with respect to solid Al was confirmed by XRS.

  17. Optimization of film synthesized rare earth transition metal permanent magnet systems

    Energy Technology Data Exchange (ETDEWEB)

    Cadieu, F.J.

    1992-01-01

    Progress is reported in three areas: high coercivity Sm-Fe-Ti-V, Sm-Fe-Zr, and two element Sm-Fe Sm{sub 5}(Fe,T){sub 17} type crystalline phases; ThMn{sub 12} type pseudobinary SmFe{sub 12-x}T{sub x}(0{le}{times}{le}1.5); and sputter process control for the synthesis of precisely textured rare earth-transition metal magnetic films. (DLC)

  18. Formation of an integrated holding company to produce rare-earth metal articles

    Science.gov (United States)

    Bogdanov, S. V.; Grishaev, S. I.

    2013-12-01

    The possibility of formation of a Russian holding company for the production of rare-earth metal articles under conditions of its increasing demand on the world market is considered. It is reasonable to ensure stable business operation on the market under conditions of state-private partnership after the fraction of soled products is determined and supported by the competitive advantages of Russian products.

  19. No Giant Two-Ion Anisotropy in the Heavy-Rare-Earth Metals

    DEFF Research Database (Denmark)

    Lindgård, Per-Anker

    1976-01-01

    A new Bose-operator expansion of tensor operators is applied to the heavy-rare-earth metals. The Er data for the cone phase have been analyzed successfully with single-ion anisotropy and isotropic exchange interaction. The Tb data can be understood on the same basis. The previously found large two......-ion anisotropy was due to an inadequate treatment of the large single-ion anisotropy leading to an incorrect expression for the spin-wave energy....

  20. Neutral binuclear rare-earth metal complexes with four μ₂-bridging hydrides.

    Science.gov (United States)

    Rong, Weifeng; He, Dongliang; Wang, Meiyan; Mou, Zehuai; Cheng, Jianhua; Yao, Changguang; Li, Shihui; Trifonov, Alexander A; Lyubov, Dmitrii M; Cui, Dongmei

    2015-03-25

    The first neutral rare-earth metal dinuclear dihydrido complexes [(NPNPN)LnH2]2 (2-Ln; Ln = Y, Lu; NPNPN: N[Ph2PNC6H3((i)Pr)2]2) bearing μ2-bridging hydride ligands have been synthesized. In the presence of THF, 2-Y undergoes intramolecular activation of the sp(2) C-H bond to form dinuclear aryl-hydride complex 3-Y containing three μ2-bridging hydride ligands.

  1. Low temperature route for the synthesis of rare earth transition metal borides and their hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Kramp, S.; Febri, M.; Joubert, J.C. [CNRS UMR 5628, Saint Martin d`Heres (France)

    1997-10-01

    Synthesis of rare earth-based alloys by the ORD technique consists in the reduction of rare earth oxides in a melt of calcium under argon, and simultaneous diffusion-reaction of the just formed rare earth metal with the other elements. This method has been applied with success to numerous ternary borides containing transition metals such as the magnetic alloys Y{sub 2}Co{sub 14}B, LnCo{sub 4}B, and YCo{sub 3}B{sub 2}. By using a small excess of Ca, boride particles grow in a viscous slurry media containing unreacted (melted) Ca and nanosize CaO particles. Single phase boride alloys can be obtained at 1000{degrees}C as loose micrometer-size particles of very high crystal quality as confirmed by the sharp diffraction peaks on the corresponding X-ray diagrams. Particles can be easily recovered by gentle wishing in diluted weak acid solution, and dried under vacuum at room temperature. This rather low temperature technique is particularly adapted to the synthesis of incongruent melting phases, as well as for the alloys containing volatile rare earth elements (Sm, Yb, Tb,...).

  2. A Low Temperature Route for the Synthesis of Rare Earth Transition Metal Borides and Their Hydrides

    Science.gov (United States)

    Kramp, S.; Febri, M.; Joubert, J. C.

    1997-10-01

    Synthesis of rare earth-based alloys by the ORD technique consists in the reduction of rare earth oxides in a melt of calcium under argon, and simultaneous diffusion-reaction of the just formed rare earth metal with the other elements. This method has been applied with success to numerous ternary borides containing transition metals such as the magnetic alloys Y2Co14B, LnCo4B, and YCo3B2. By using a small excess of Ca, boride particles grow in a viscous slurry media containing unreacted (melted) Ca and nanosize CaO particles. Single phase boride alloys can be obtained at 1000°C as loose micrometer-size particles of very high crystal quality as confirmed by the sharp diffraction peaks on the corresponding X-ray diagrams. Particles can be easily recovered by gentle washing in diluted weak acid solution, and dried under vacuum at room temperature. This rather low temperature technique is particularly adapted to the synthesis of incongruent melting phases, as well as for the alloys containing volatile rare earth elements (Sm, Yb, Tb,…).

  3. Effect of Rare Earth Metals on Structure and Properties of Electroless Co-B Alloy Coating

    Institute of Scientific and Technical Information of China (English)

    宣天鹏; 张雷; 黄秋华

    2002-01-01

    The effect of rare earth metals cerium, lanthanum and yttrium on chemical composition, structure and properties of electroless Co-B alloy coating was studied. By plasma transmitting spectrograph, electron energy spectrometer, X-ray diffractometter, micro-hardometer and vibratory sample magnetometer the chemical constitution, structure and properties of the alloy coatings were analyzed and inspected. The results show that with a tiny quantity of rare earth metal added into Co-B alloy coating, the content of boron is decreased in the alloy coatings, and the kinds of rare earth metal have enormous effect on the structure and properties of electroless Co-B alloy coating. At the same time electroless Co-B alloy with amorphous structure is transformed to electroless Co-B-RE alloy with microcrystalline or crystalline structure. In this way microhardness of the coatings is increased remarkably. Cerium and lanthanum would also increase the saturated magnetic intensity and decrease coercitive force of the coating. So soft magnetization of the coatings would be improved.

  4. Fullerene-C60 and crown ether doped on C60 sensors for high sensitive detection of alkali and alkaline earth cations

    Science.gov (United States)

    Zaghmarzi, Fatemeh Alipour; Zahedi, Mansour; Mola, Adeleh; Abedini, Saboora; Arshadi, Sattar; Ahmadzadeh, Saeed; Etminan, Nazanin; Younesi, Omran; Rahmanifar, Elham; Yoosefian, Mehdi

    2017-03-01

    Fullerenes are effective acceptor components with high electron affinity for charge transfer. The significant influences of chemical adsorption of the cations on the electrical sensitivity of pristine C60 and 15-(C2H4O)5/C60 nanocages could be the basis of new generation of electronic sensor design. The density functional theory calculation for alkali and alkaline earth cations detection by pristine C60 and 15-(C2H4O)5/C60 nanocages are considered at B3LYP level of theory with 6-31 G(d) basis set. The quantum theory of atoms in molecules analysis have been performed to understand the nature of intermolecular interactions between the cations and nanocages. Also, the natural bond orbital analysis have been performed to assess the intermolecular interactions in detail. Furthermore, the frontier molecular orbital, energy gap, work function, electronegativity, number of transferred electron (∆N), dipole moment as well as the related chemical hardness and softness are investigated and calculated in this study. The results show that the adsorption of cations (M=Na+, K+, Mg2+ and Ca2+) are exothermic and the binding energy in pristine C60 nanocage and 15-(C2H4O)5/C60 increases with respect to the cations charge. The results also denote a decrease in the energy gap and an increase in the electrical conductivity upon the adsorption process. In order to validate the obtained results, the density of state calculations are employed and presented in the end as well.

  5. Interaction of Rydberg atoms in circular states with the alkaline-earth Ca(4s{sup 2}) and Sr(5s{sup 2}) atoms

    Energy Technology Data Exchange (ETDEWEB)

    Mironchuk, E. S.; Narits, A. A.; Lebedev, V. S., E-mail: vlebedev@sci.lebedev.ru [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation)

    2015-11-15

    The resonant mechanism of interaction of alkaline-earth atoms having a low electron affinity to Rydberg atoms in circular (l = vertical bar m vertical bar = n–1) and near-circular states has been studied. To describe the dynamics of resonant processes accompanied by nonadiabatic transitions between ionic and Rydberg covalent terms of a quasimolecule, an approach based on the integration of coupled equations for the probability amplitudes has been developed taking into account the possibility of the decay of an anion in the Coulomb field of the positive ionic core of a highly excited atom. The approach involves the specific features of the problem associated with the structure of the wavefunction of a Rydberg electron in states with high orbital angular momenta l ∼ n–1. This approach provides a much more accurate description of the dynamics of electronic transitions at collisions between atoms than that within the modified semiclassical Landau–Zener model. In addition, this approach makes it possible to effectively take into account many channels of the problem. The cross sections for resonant quenching of Rydberg states of the Li(nlm) atom with given principal n, orbital l = n–1, and magnetic m quantum numbers at thermal collisions with the Ca(4s{sup 2}) and Sr(5s{sup 2}) atoms have been calculated. The dependences of the results on n, m, and angle α between the relative velocity of the atoms and the normal to the plane of the orbit of the Rydberg electron have been obtained. The influence of orientational effects on the efficiency of the collisional destruction of circular and near-circular states has been studied. The results indicate a higher stability of such states to their perturbations by neutral particles as compared to usually studied nl states with low values of l (l ≪ n)

  6. Interaction of Rydberg atoms in circular states with the alkaline-earth Ca(4 s 2) and Sr(5 s 2) atoms

    Science.gov (United States)

    Mironchuk, E. S.; Narits, A. A.; Lebedev, V. S.

    2015-11-01

    The resonant mechanism of interaction of alkaline-earth atoms having a low electron affinity to Rydberg atoms in circular ( l = | m| = n-1) and near-circular states has been studied. To describe the dynamics of resonant processes accompanied by nonadiabatic transitions between ionic and Rydberg covalent terms of a quasimolecule, an approach based on the integration of coupled equations for the probability amplitudes has been developed taking into account the possibility of the decay of an anion in the Coulomb field of the positive ionic core of a highly excited atom. The approach involves the specific features of the problem associated with the structure of the wavefunction of a Rydberg electron in states with high orbital angular momenta l ~ n-1. This approach provides a much more accurate description of the dynamics of electronic transitions at collisions between atoms than that within the modified semiclassical Landau-Zener model. In addition, this approach makes it possible to effectively take into account many channels of the problem. The cross sections for resonant quenching of Rydberg states of the Li( nlm) atom with given principal n, orbital l = n-1, and magnetic m quantum numbers at thermal collisions with the Ca(4 s 2) and Sr(5 s 2) atoms have been calculated. The dependences of the results on n, m, and angle α between the relative velocity of the atoms and the normal to the plane of the orbit of the Rydberg electron have been obtained. The influence of orientational effects on the efficiency of the collisional destruction of circular and near-circular states has been studied. The results indicate a higher stability of such states to their perturbations by neutral particles as compared to usually studied nl states with low values of l ( l ≪ n).

  7. Influence of elevated alkalinity and natural organic matter (NOM) on tissue-specific metal accumulation and reproductive performance in fathead minnows during chronic, multi-trophic exposures to a metal mine effluent.

    Science.gov (United States)

    Ouellet, Jacob D; Dubé, Monique G; Niyogi, Som

    2013-09-01

    Metal bioavailability in aquatic organisms is known to be influenced by various water chemistry parameters. The present study examined the influence of alkalinity and natural organic matter (NOM) on tissue-specific metal accumulation and reproductive performance of fathead minnows (Pimephales promelas) during environmentally relevant chronic exposures to a metal mine effluent (MME). Sodium bicarbonate (NaHCO3) or NOM (as commercial humic acid) were added to a Canadian MME [45 percent process water effluent (PWE)] in order to evaluate whether increases in alkalinity (3-4 fold) or NOM (~1.5-3mg/L dissolved organic carbon) would reduce metal accumulation and mitigate reproductive toxicity in fathead minnows during a 21-day multi-trophic exposure. Eleven metals (barium, boron, cobalt, copper, lithium, manganese, molybdenum, nickel, rubidium, selenium, and strontium) were elevated in the 45 percent PWE relative to the reference water. Exposure to the unmodified 45 percent PWE resulted in a decrease of fathead minnow egg production (~300 fewer eggs/pair) relative to the unmodified reference water, over the 21-day exposure period. Water chemistry modifications produced a modest decrease in free ion activity of some metals (as shown by MINTEQ, Version 3) in the 45 percent PWE exposure water, but did not alter the metal burden in the treatment-matched larval Chironomus dilutus (the food source of fish during exposure). The tissue-specific metal accumulation increased in fish exposed to the 45 percent PWE relative to the reference water, irrespective of water chemistry modifications, and the tissue metal concentrations were found to be similar between fish in the unmodified and modified 45 percent PWE (higher alkalinity or NOM) treatments. Interestingly however, increased alkalinity and NOM markedly improved fish egg production both in the reference water (~500 and ~590 additional eggs/pair, respectively) and 45 percent PWE treatments (~570 and ~260 additional eggs

  8. Rare earth elements and critical metal content of extracted landfilled material and potential recovery opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Gutiérrez-Gutiérrez, Silvia C.; Coulon, Frédéric; Jiang, Ying; Wagland, Stuart, E-mail: s.t.wagland@cranfield.ac.uk

    2015-08-15

    Highlights: • Samples from multiple core drills were obtained from 4× landfill sites in the UK. • Each sample analysed for rare earth elements, critical metals and valuable metals. • Two stage microwave digestion method ensuring high yield. • High quantities of copper and aluminium were observed in the soil layers of landfill. • Across 4× landfills aluminium and copper present has a value of around $400 million. - Abstract: Rare earth elements (REEs), Platinum group metals (PGMs) and other critical metals currently attract significant interest due to the high risks of supply shortage and substantial impact on the economy. Their uses in many applications have made them present in municipal solid waste (MSW) and in commercial and industrial waste (C&I), since several industrial processes produce by-products with high content of these metals. With over 4000 landfills in the UK alone, the aim of this study was to assess the existence of these critical metals within landfills. Samples collected from four closed landfills in UK were subjected to a two-step acid digestion to extract 27 metals of interest. Concentrations across the four landfill sites were 58 ± 6 mg kg{sup −1} for REEs comprising 44 ± 8 mg kg{sup −1} for light REEs, 11 ± 2 mg kg{sup −1} for heavy REEs and 3 ± 1 mg kg{sup −1} for Scandium (Sc) and 3 ± 1.0 mg kg{sup −1} of PGMs. Compared to the typical concentration in ores, these concentrations are too low to achieve a commercially viable extraction. However, content of other highly valuable metals (Al and Cu) was found in concentrations equating to a combined value across the four landfills of around $400 million, which increases the economic viability of landfill mining. Presence of critical metals will mainly depend on the type of waste that was buried but the recovery of these metals through landfill mining is possible and is economically feasible only if additional materials (plastics, paper, metallic items and other) are

  9. Metal-silicate Partitioning and Its Role in Core Formation and Composition on Super-Earths

    Science.gov (United States)

    Schaefer, Laura; Jacobsen, Stein B.; Remo, John L.; Petaev, M. I.; Sasselov, Dimitar D.

    2017-02-01

    We use a thermodynamic framework for silicate-metal partitioning to determine the possible compositions of metallic cores on super-Earths. We compare results using literature values of the partition coefficients of Si and Ni, as well as new partition coefficients calculated using results from laser shock-induced melting of powdered metal-dunite targets at pressures up to 276 GPa, which approaches those found within the deep mantles of super-Earths. We find that larger planets may have little to no light elements in their cores because the Si partition coefficient decreases at high pressures. The planet mass at which this occurs will depend on the metal-silicate equilibration depth. We also extrapolate the equations of state (EOS) of FeO and FeSi alloys to high pressures, and present mass–radius diagrams using self-consistent planet compositions assuming equilibrated mantles and cores. We confirm the results of previous studies that the distribution of elements between mantle and core will not be detectable from mass and radius measurements alone. While observations may be insensitive to interior structure, further modeling is sensitive to compositionally dependent properties, such as mantle viscosity and core freeze-out properties. We therefore emphasize the need for additional high pressure measurements of partitioning as well as EOSs, and highlight the utility of the Sandia Z-facilities for this type of work.

  10. Earth

    CERN Document Server

    Carter, Jason

    2017-01-01

    This curriculum-based, easy-to-follow book teaches young readers about Earth as one of the eight planets in our solar system in astronomical terms. With accessible text, it provides the fundamental information any student needs to begin their studies in astronomy, such as how Earth spins and revolves around the Sun, why it's uniquely suitable for life, its physical features, atmosphere, biosphere, moon, its past, future, and more. To enhance the learning experience, many of the images come directly from NASA. This straightforward title offers the fundamental information any student needs to sp

  11. Improvement of corrosion resistance of magnesium metal by rare earth elements

    Energy Technology Data Exchange (ETDEWEB)

    Takenaka, Toshihide [Department of Production Systems Engineering, Toyohashi University of Technology, Toyohashi 441-8580 (Japan)], E-mail: takenaka@pse.tut.ac.jp; Ono, Takami; Narazaki, Yuji; Naka, Yusuke; Kawakami, Masahiro [Department of Production Systems Engineering, Toyohashi University of Technology, Toyohashi 441-8580 (Japan)

    2007-11-20

    Mg metal containing rare earth metals (REs) can be electrowon directly by molten salt electrolysis. The clarification of the optimum RE content in Mg is necessary to fix the electrolytic conditions in the direct electrowinning of Mg with RE. From this point of view, effect of RE addition in Mg metal on its corrosion property was studied in detail in this study. The specimen was prepared by adding La, Nd, or Ce in melted Mg metal, and its corrosion resistance was examined by an immersion test in 3 mass%-NaCl solution at room temperature. The corrosion resistance of Mg was improved greatly by adding a small amount of RE, whereas the excess addition of RE deteriorated the corrosion resistance. The optimum RE content was about 0.5 mass%. In this study, the corrosion property of Mg with an artificial surface oxide layer was also studied to clarify the effect of surface oxide. The corrosion resistance of Mg was particularly strengthened by conversion coating in a solution including La(NO{sub 3}){sub 3}, Nd(NO{sub 3}){sub 3}, or Ce(NO{sub 3}){sub 3}, with Mg(NO{sub 3}){sub 2}. This result suggests that the surface oxide film consisting of both Mg and RE gives ideal corrosion resistance to Mg metal. Mg metal with conversion coating including RE should also be of use as a corrosion-resistant material.

  12. Modification of Non-Metallic Inclusions by Rare-Earth Elements in Microalloyed Steels

    Directory of Open Access Journals (Sweden)

    M. Opiela

    2012-04-01

    Full Text Available The modification of the chemical composition of non-metallic inclusions by rare-earth elements in the new-developed microalloyed steels was discussed in the paper. The investigated steels are assigned to production of forged elements by thermo- mechanical treatment. The steels were melted in a vaccum induction furnace and modification of non-metallic inclusions was carried out by the michmetal in the amount of 2.0 g per 1 kg of steel. It was found that using material charge of high purity and a realization of metallurgical process in vacuous conditions result in a low concentration of sulfur (0.004%, phosphorus (from 0.006 to 0.008% and oxygen (6 ppm. The high metallurgical purity is confirmed by a small fraction of non-metallic inclusions averaging 0.075%. A large majority of non-metallic inclusions are fine, globular oxide-sulfide or sulfide particles with a mean size 17m2. The chemical composition and morphology of non-metallic inclusions was modified by Ce, La and Nd, what results a small deformability of non- metallic inclusions during hot-working.

  13. How Does Boiling in the Earth's Crust Influence Metal Speciation and Transport?

    Science.gov (United States)

    Kam, K.; Lemke, K.

    2014-12-01

    The presence of large quantities of precious metals, such as gold and copper, near the Earth's surface (upper crust) is commonly attributed to transport in aqueous solution and precipitation upon variations in temperature and pressure. As a consequence, gold exploration is closely linked to solution chemistry, i.e. hydrothermal processes involving aqueous fluids with densities of around unity. However, as crustal fluids buoyantly ascend, boiling produces a coexisting low-density aqueous liquid with fundamentally different physical and chemical properties, and a, most importantly, a high affinity for coinage metals (Heinrich et al., Econ Geol., 1992, 87, 1566). From recent experimental studies of Au (Hurtig and Williams-Jones, 2014, Geochim. Cosmochim. Acta,, 127, 304), we know that metal speciation in this low-density phase differs fundamentally from that observed in bulk solution, clearly, with important implications for Au, and metal speciation in general, transport and ore concentrations processes (these processes would also be operable in industrial geothermal plants given the quite special solvent properties of steam). In brief, this study focuses on the speciation of select metal halides in bulk solution as well as in water vapor, and is driven by our need to understand the solvent properties of around 2.0x109 cubic kilometers of free water (or 2,500 times as much water as stored in all lakes and rivers) present in the Earth's crust. The scope of this study has particular applications in the geothermal and oil industries, as both deal with high temperature low-density aqueous fluids. Understanding how metal halide species behave upon boiling can also provide insight into how metals, such as copper and silver, coat turbine equipment and steam piping in geothermal plants, ultimately rendering these components inoperable. This study will also provide preliminary results from mass spectrometric experiments of transition metal halides, and will be augmented with

  14. Recovery of rare earths from acid leach solutions of spent nickel-metal hydride batteries using solvent extraction

    Institute of Scientific and Technical Information of China (English)

    夏允; 肖连生; 田吉英; 李兆洋; 曾理

    2015-01-01

    The extraction of rare earths from acid leach solutions of spent nickel-metal hydride batteries using a primary amine ex-tractant of N1923 was studied. The effects of feed pH, temperature, agitation rate and time on the extraction of rare earths, as well as stripping agent composition and concentration, phase ratio on the stripping were investigated. In addition, the extraction isotherm was determined. The pilot plant test results showed that the extraction of rare earths reached 99.98% after a five-stage counter current ex-traction. The mixed rare earths oxalates with the 99.77% purity of rare earth elements and impurity content less than 0.05% were ob-tained by the addition of oxalic acids in loaded strip liquors. The extractant exhibited good selectivity of rare earths over base metals of iron, nickel, copper and manganese.

  15. Influence of rare earth metals on the nucleation and solidification behavior of iron and 1045 steel

    Science.gov (United States)

    Li, H.; McLean, A.; Rutter, J. W.; Sommerville, I. D.

    1988-06-01

    Two series of experiments have been conducted to determine the influence of rare earth additions on the nucleation and crystallization behavior of pure iron and 1045 steel. In the first series, additions of rare earth suicide or cerium dioxide powder to two-Kg 1045 steel ingots indicated that rare earth suicide can refine the as-cast structure of such ingots. However, if the holding time after rare earth silicide addition is over two minutes, the grain refinement decreases. With cerium dioxide additions, a relatively large columnar zone was obtained. In the second series, the effects of cerium metal or cerium dioxide powder additions on the degree of undercooling obtainable in pure iron and 1045 steel were examined by the lévitation melting method. Surface tension measurements of the levitated droplets were carried out at the same time to investigate the possible effects of surface tension variations on the nucleation and crystallization behavior of the metals. The experimental data show that rare earth inclusions can greatly reduce the degree of undercooling of iron and steel, and that a small amount of dissolved cerium can further reduce the degree of undercooling of levitated droplets. The structure and reaction products obtained with Fe-Ce levitated droplets were examined with both optical and scanning electron microscopy as well as X-ray diffraction analysis. The experimental results clearly indicated that cerium solute redistribution during solidification is the dominant factor in refining the as-cast structure. A nucleation and solidification model for the Fe-Ce levitated droplets has been developed, which can successfully explain the experimental results.

  16. Impact Wear Properties of Metal-Plastic Multilayer Composites Filled with Glass Fiber Treated with Rare Earth Element Surface Modifier

    Institute of Scientific and Technical Information of China (English)

    程先华; 薛玉君

    2001-01-01

    The friction and wear properties of metal-plastic multilayer composites filled with glass fiber, which is treated with rare earth element surface modifier, under impact load and dry friction conditions were investigated. Experimental results show that the metal-plastic multilayer composite filled with glass fiber exhibits excellent friction and impact wear properties when using rare earth elements as surface modifier for the surface treatment of glass fiber.

  17. Extent of metal-silicate disequilibrium during accretion and early differentiation of the Earth

    Science.gov (United States)

    Rubie, D. C.; Nimmo, F.; Morbidelli, A.; Frost, D. J.

    2012-12-01

    Earth, Mars, Venus and Mercury accreted on a timescale of 10-100 My through a series of violent collisions with planetesimals and embryos. The high energy of such impacts was sufficient to cause deep magma ocean formation which facilitated the segregation of metal and silicate liquids. Planetary cores thus formed as a multistage process that was inseparable from the accretion process. In order to better understand the formation and early differentiation of the terrestrial planets, we are integrating a multistage core-formation model with N-body accretion simulations. Constraints on model parameters are the compositions of the Earth's primitive mantle and, to a lesser extent, the mantles of Mars and Mercury which may be FeO rich and FeO-poor respectively. We use a least-squares minimization to optimise 4 model parameters. Elements currently considered include Si, O, Ni, Co, W, Nb, Cr, Ta and V. We concentrate on recent N-body simulations that result in an approximately Earth-mass planet at ~1 AU. In order to satisfy the model constraints, accretion has to be heterogeneous, with embryos and planetesimals originating in the inner part of the solar system (e.g. emulsify and equilibrate in a magma ocean and (2) the fraction of magma oceans that are involved in the equilibration process for both impacting planetesimals and embryos. Both estimates are crucial for interpreting Hf-W age determinations. Best results are obtained when the fraction of silicate mantle/magma ocean that interacts chemically with the metallic cores of impactors is limited and lies in the range 0.003 to 0.1, depending on the size of the impactor and magma ocean depth. The degree of incomplete metal equilibration depends on the extent to which the impactor's mantle participates in the metal-silicate equilibration process.

  18. The atmospheric circulation of the super Earth GJ 1214b: Dependence on composition and metallicity

    CERN Document Server

    Kataria, Tiffany; Fortney, Jonathan J; Marley, Mark S; Freedman, Richard S

    2014-01-01

    We present three-dimensional atmospheric circulation models of GJ 1214b, a 2.7 Earth-radius, 6.5 Earth-mass super Earth detected by the MEarth survey. Here we explore the planet's circulation as a function of atmospheric metallicity and atmospheric composition, modeling atmospheres with a low mean-molecular weight (i.e., H2-dominated) and a high mean-molecular weight (i.e. water- and CO2-dominated). We find that atmospheres with a low mean-molecular weight have strong day-night temperature variations at pressures above the infrared photosphere that lead to equatorial superrotation. For these atmospheres, the enhancement of atmospheric opacities with increasing metallicity lead to shallower atmospheric heating, larger day-night temperature variations and hence stronger superrotation. In comparison, atmospheres with a high mean-molecular weight have larger day-night and equator-to-pole temperature variations than low mean-molecular weight atmospheres, but differences in opacity structure and energy budget lead ...

  19. Rare-earth transition-metal intermetallics: Structure-bonding-property relationships

    Energy Technology Data Exchange (ETDEWEB)

    Han, M. K. [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    The explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding property relationships. The work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe13-xSix system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn{sub 13}-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides Re2-xFe4Si14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi2: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb3Zn3.6Al7.4: Partially ordered structure of Tb3Zn3.6Al7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn39(CrxAl1-x)81

  20. Rare-Earth Transition-Metal Intermetallics: Structure-bonding-Property Relationships

    Energy Technology Data Exchange (ETDEWEB)

    Han, Mi-Kyung [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    Our explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding-property relationships. Our work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe13-xSix system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn13-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides RE2-xFe4Si14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi2: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb3Zn3.6Al7.4: Partially ordered structure of Tb3.6Zn13-xAl7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn39(CrxAl1-x

  1. Fabrication and Characterization of Glass-Ceramics Doped with Rare Earth Oxide and Heavy Metal Oxide

    Institute of Scientific and Technical Information of China (English)

    陈国华; 刘心宇; 成钧

    2004-01-01

    Cordierite-based glass-ceramics with non-stoichiometric composition doped with rare earth oxide (REO2) and heavy metal oxide (M2O3) respectively were fabricated from glass powders. After sintering and crystallization heat treatment, various physical properties, including compact density and apparent porosity, were examined to evaluate the sintering behavior of cordierite-based glass-ceramics. Results show that the additives both heavy metal oxide and rare earth oxide promote the sintering and lower the phase temperature from μ- to α-cordierite as well as affect the dielectric properties of sintered glass-ceramics. The complete-densification temperature for samples is as low as 900 ℃. The materials have a low dielectric constant (≈5), a low thermal expansion coefficient ((2.80~3.52)×10-6 ℃-1) and a low dissipation factor (≤0.2%) and can be co-fired with high conductivity metals such as Au, Cu, Ag/Pd paste at low temperature (below 950 ℃), which makes it to be a promising material for low-temperature co-fired ceramic substrates.

  2. Molecular heterometallic hydride clusters composed of rare-earth and d-transition metals.

    Science.gov (United States)

    Shima, Takanori; Luo, Yi; Stewart, Timothy; Bau, Robert; McIntyre, Garry J; Mason, Sax A; Hou, Zhaomin

    2011-09-18

    Heteromultimetallic hydride clusters containing both rare-earth and d-transition metals are of interest in terms of both their structure and reactivity. However, such heterometallic complexes have not yet been investigated to a great extent because of difficulties in their synthesis and structural characterization. Here, we report the synthesis, X-ray and neutron diffraction studies, and hydrogen addition and release properties of a family of rare-earth/d-transition-metal heteromultimetallic polyhydride complexes of the core structure type 'Ln(4)MH(n)' (Ln = Y, Dy, Ho; M = Mo, W; n = 9, 11, 13). Monitoring of hydrogen addition to a hydride cluster such as [{(C(5)Me(4)SiMe(3))Y}(4)(μ-H)(9)Mo(C(5)Me(5))] in a single-crystal to single-crystal process by X-ray diffraction has been achieved for the first time. Density functional theory studies reveal that the hydrogen addition process is cooperatively assisted by the Y/Mo heteromultimetallic sites, thus offering unprecedented insight into the hydrogen addition and release process of a metal hydride cluster.

  3. Chemical composition of modern and fossil hippopotamid teeth and implications for paleoenvironmental reconstructions and enamel formation - Part 2: Alkaline earth elements as tracers of watershed hydrochemistry and provenance

    Science.gov (United States)

    Brügmann, G.; Krause, J.; Brachert, T. C.; Stoll, B.; Weis, U.; Kullmer, O.; Ssemmanda, I.; Mertz, D. F.

    2012-11-01

    This study demonstrates that alkaline earth elements in enamel of hippopotamids, in particular Ba and Sr, are tracers for water provenance and hydrochemistry in terrestrial settings. The studied specimens are permanent premolar and molar teeth found in modern and fossil lacustrine sediments of the Western Branch of the East African Rift system (Lake Kikorongo, Lake Albert, and Lake Malawi) and from modern fluvial environments of the Nile River. Concentrations in enamel vary by two orders of magnitude for Ba (120-9336 μg g-1) as well as for Sr (9-2150 μg g-1). The variations are partially induced during post-mortem alteration and during amelogenesis, but the major contribution originates ultimately from the variable water chemistry in the habitats of the hippopotamids which is controlled by the lithologies and weathering processes in the watershed areas. Amelogenesis causes a distinct distribution of MgO, Ba and Sr in modern and fossil enamel, in that element concentrations increase along profiles from the outer rim towards the enamel-dentin junction by a factor of 1.3-1.9. These elements are well correlated in single specimens, thus suggesting that their distribution is determined by a common, single process, which can be described by closed system Rayleigh crystallization of bioapatite in vivo. Enamel from most hippopotamid specimens has Sr/Ca and Ba/Ca which are typical for herbivores. However, Ba/Sr ranges from 0.1 to 3 and varies on spatial and temporal scales. Thus, Sr concentrations and Ba/Sr in enamel differentiate between habitats having basaltic mantle rocks or Archean crustal rocks as the ultimate sources of Sr and Ba. This provenance signal is modulated by climate change. In Miocene to Pleistocene enamel from the Lake Albert region, Ba/Sr decreases systematically with time from 2 to 0.5. This trend can be correlated with changes in climate from humid to arid, in vegetation from C3 to C4 biomass as well as with increasing evaporation of the lake water

  4. Enhanced Laser Cooling of Rare-Earth-Ion-Doped Glass Containing Nanometer-Sized Metallic Particles

    Institute of Scientific and Technical Information of China (English)

    JIA You-Hun; ZHONG Biao; YIN Jian-Ping

    2009-01-01

    The enhanced laser cooling performance of rare-earth-ions-doped glasses containing small particles is predicted. This is achieved by the enhancement of local field around rare earth ions, owing to the surface plasmon resonance of small metallic particles. The role of energy transfer between ions and the particle is theoretical discussed. Depending on the particle size and the ion emission quantum efficiency, the enhancement of the absorption and the fluorescence is predicted. Moreover, taking Yb3+-doped ZBLAN as example, the cooling power and heat-light converting efficiency are calculated. It is finally concluded that the absorption and the fluorescence are greatly enhanced in these composite materials, the cooling power is increased compared to the bulk material.

  5. EVALUATION OF RADIOLOGICAL SIGNIFICANCE OF RARE-EARTH METALS WITH NATURAL RADIOACTIVE ISOTOPES

    Directory of Open Access Journals (Sweden)

    E. P. Lisachenko

    2013-01-01

    Full Text Available Among the rare-earth metals with natural radioactive isotopes, lantan, lutetium and samarium are allocated a relatively high specific activity. The formation of the additional external radiation keep it close to the significance of the materials to the radiation categories of materials with a high content of natural radionuclides of uranium and thorium family, lanthanum value is much less. Samarium, with acceptable toxicology content in the working area, forms the internal exposure to the limits for professionals. The use of these elements in science and industry requires the radiation-hygienic evaluation.

  6. Narcissistic self-sorting in self-assembled cages of rare Earth metals and rigid ligands.

    Science.gov (United States)

    Johnson, Amber M; Wiley, Calvin A; Young, Michael C; Zhang, Xing; Lyon, Yana; Julian, Ryan R; Hooley, Richard J

    2015-05-04

    Highly selective, narcissistic self-sorting can be achieved in the formation of self-assembled cages of rare earth metals with multianionic salicylhydrazone ligands. The assembly process is highly sensitive to the length of the ligand and the coordination geometry. Most surprisingly, high-fidelity sorting is possible between ligands of identical coordination angle and geometry, differing only in a single functional group on the ligand core, which is not involved in the coordination. Supramolecular effects allow discrimination between pendant functions as similar as carbonyl or methylene groups in a complex assembly process.

  7. Processing of Phosphorus Slag with Recovery of Rare Earth Metals and Obtaining Silicon Containing Cake

    Science.gov (United States)

    Karshigina, Zaure; Abisheva, Zinesh; Bochevskaya, Yelena; Akcil, Ata; Sharipova, Aynash; Sargelova, Elmira

    2016-10-01

    The present research is devoted to the processing of slag generating during the yellow phosphorus production. In this paper are presented studies on leaching of phosphorus production slag by nitric acid with recovery of rare earth metals (REMs) into solution. REMs recovery into the solution achieved 98 % during the leaching process with using 7.5 mol/L of HNO3, liquid-to-solid ratio is 2.6:1, temperature is 60°C, process duration is 1 hour and stirrer speed is 500 rpm. Behaviour during the leaching of associated components such as calcium, aluminium, and iron was studied. After the leaching cake contains ∼⃒75-85 % of SiO2 and it might be useful for obtaining of precipitated silicon dioxide. With the purpose of separation from the impurities, recovery and concentrating of REMs, the obtained solution after leaching was subjected to extraction processing methods. The influence of ratio of organic and aqueous phases (O: A) on the extraction of rare earth metals by tributyl phosphate (TBP) with concentrations from 20 up to 100 % was studied. The REMs extraction with increasing TBP concentration under changes O:A ratio from 1:20 down to 1:1 into the organic phase from the solutions after nitric acid leaching increased from 22.2 up to 99.3%. The duration effect of REMs extraction process was studied by tributyl phosphate. It is revealed that with increasing of duration of the extraction process from 10 to 30 minutes REMs recovery into the organic phase almost did not changed. The behaviour of iron in the extraction process by TBP was studied. It was found that such accompanying components as calcium and aluminium by tributyl phosphate didn't extracted. To construct isotherm of REMs extraction of by tributyl phosphate was used variable volume method. It was calculated three-step extraction is needed for REMs recovery from the solutions after nitric acid leaching of phosphorus production slag. The process of the three-steps counter current extraction of rare earth

  8. Anomalous positive flatband voltage shifts in metal gate stacks containing rare-earth oxide capping layers

    KAUST Repository

    Caraveo-Frescas, J. A.

    2012-03-09

    It is shown that the well-known negative flatband voltage (VFB) shift, induced by rare-earth oxide capping in metal gate stacks, can be completely reversed in the absence of the silicon overlayer. Using TaN metal gates and Gd2O3-doped dielectric, we measure a ∼350 mV negative shift with the Si overlayer present and a ∼110 mV positive shift with the Si overlayer removed. This effect is correlated to a positive change in the average electrostatic potential at the TaN/dielectric interface which originates from an interfacial dipole. The dipole is created by the replacement of interfacial oxygen atoms in the HfO2 lattice with nitrogen atoms from TaN.

  9. Preparation and mechanism study of bulk pure rare-earth metals with amorphous and nanocrystalline structures

    Institute of Scientific and Technical Information of China (English)

    LI ErDong; SONG XiaoYan; ZHANG JiuXing; LU NianDuan

    2007-01-01

    The preparation and the mechanism study of bulk pure rare-earth metals with amorphous and nanocrystalline structures, which were produced by spark plasma sintering (SPS), were carried out in this paper. With different processing parameters, the amorphous, two phases of amorphous and nanocrystalline, and complete nanocrystalline microstructures have been obtained. The nano-grain sizes in the bulk nanocrystalline materials are found smaller than the original powder particles sizes, which may change the conventional viewpoint that the grains in the sintered bulk are generally coarser than the raw powder particles. The technique developed in the present work can be extended to the preparation of many other nano bulk metal materials, and thus enables the studies of the nano-size effects on the physical, chemical and mechanical properties of bulk nano materials.

  10. Rare earth metals in North America; Zeldzame aardmetalen in Noord-Amerika

    Energy Technology Data Exchange (ETDEWEB)

    Louzada, K.

    2012-11-15

    The uncertain supply of rare earth metals (Rare Earth Elements) from China for the high tech industry in the U.S. is a barrier for innovation and the high-tech manufacturing industry. Many rare earths are applied in permanent magnets for sustainable energy generation and for energy storage systems in for example electric cars. Also other sectors feel the pressure of shortages. The federal government in the USA and US companies use the opportunity to encourage research into recycling, reducing the use and finding alternatives for rare earths. Canada sees in the uncertain supply and dwindling reserves in the USA and elsewhere an economic opportunity. Canada can start the development of hitherto unprofitable reserves of valuable materials. Both in the USA and Canada, the number of exploration projects in the mining industry has grown significantly [Dutch] De onzekere aanvoer van zeldzame aardmetalen (Rare Earth Elements) uit China voor de hightechindustrie vormt in de VS een hindernis voor innovatie en voor de hightech maakindustrie. Met name in permanente magneten voor duurzame energieopwekking en energieopslagsystemen voor bijvoorbeeld elektrische auto's worden veel zeldzame aardmetalen verwerkt. Ook andere sectoren staan onder druk. De federale overheid en bedrijven in de VS maken van de gelegenheid gebruik om onderzoek naar de recycling, vermindering van het gebruik en alternatieven voor zeldzame aardmetalen te stimuleren. Canada ziet de onzekere aanvoer en slinkende reserves in de VS en elders als een economische kans. Het land kan tot nu toe onrendabele voorkomens van de waardevolle materialen gaan ontwikkelen. Zowel in de VS als in Canada is het aantal exploratieprojecten in de mijnbouw aanzienlijk gegroeid.

  11. Development of a capillary electrophoresis method for the analysis in alkaline media as polyoxoanions of two strategic metals: Niobium and tantalum.

    Science.gov (United States)

    Deblonde, Gauthier J-P; Chagnes, Alexandre; Cote, Gérard; Vial, Jérôme; Rivals, Isabelle; Delaunay, Nathalie

    2016-03-11

    Tantalum (Ta) and niobium (Nb) are two strategic metals essential to several key sectors, like the aerospace, gas and oil, nuclear and electronic industries, but their separation is really difficult due to their almost identical chemical properties. Whereas they are currently produced by hydrometallurgical processes using fluoride-based solutions, efforts are being made to develop cleaner processes by replacing the fluoride media by alkaline ones. However, methods to analyze Nb and Ta simultaneously in alkaline samples are lacking. In this work, we developed a capillary zone electrophoresis (CE) method able to separate and quantify Nb and Ta directly in alkaline media. This method takes advantage of the hexaniobate and hexatantalate ions which are naturally formed at pH>9 and absorb in the UV domain. First, the detection conditions, the background electrolyte (BGE) pH, the nature of the BGE co-ion and the internal standard (IS) were optimized by a systematic approach. As the BGE counter-ion nature modified the speciation of both ions, sodium- and lithium-based BGE were tested. For each alkaline cation, the BGE ionic strength and separation temperature were optimized using experimental designs. Since changes in the migration order of IS, Nb and Ta were observed within the experimental domain, the resolution was not a monotonic function of ionic strength and separation temperature. This forced us to develop an original data treatment for the prediction of the optimum separation conditions. Depending on the consideration of either peak widths or peak symmetries, with or without additional robustness constraints, four optima were predicted for each tested alkaline cation. The eight predicted optima were tested experimentally and the best experimental optimum was selected considering analysis time, resolution and robustness. The best separation was obtained at 31.0°C and in a BGE containing 10mM LiOH and 35mM LiCH3COO.The separation voltage was finally optimized

  12. Modification of radiation sensitivity by salts of the metals beryllium and indium and the rare earths cerium, lanthanum and scandium.

    Science.gov (United States)

    Floersheim, G L

    1995-03-01

    The LD50 of 46 salts of metals and rare earths (lanthanoids) was determined in mice. Half the LD50 of the compounds was then combined with lethal radiation (10.5 Gy) and the modification of survival time was scored. Only the metals beryllium and indium and the rare earths cerium, lanthanum and scandium displayed activity in our assay. They were then tested at a wider range of lower doses and reduced survival time in a dose-dependent fashion. This appears to be compatible with enhancement of radiation sensitivity. The interaction of these metals and rare earths with radiation adds a new facet to their toxicological spectrum and, by enhancing radiation effects, may influence estimates of risk. On the other hand, the radiosensitizing properties of the metals may be useful for further development of compounds to be used as adjuncts in specific situations of cancer radiotherapy.

  13. Rare Earth Metal Complexes of Bidentate Nitroxide Ligands: Synthesis and Electrochemistry.

    Science.gov (United States)

    Kim, Jee Eon; Bogart, Justin A; Carroll, Patrick J; Schelter, Eric J

    2016-01-19

    We report rare earth metal complexes with tri- and bidentate ligands including strongly electron-donating nitroxide groups. The tridentate ligand 1,3,5-tris(2'-tert-butylhydroxylaminoaryl)benzene (H3arene-triNOx) was complexed to cerium(IV) in a 2:1 ligand-to-metal stoichiometry as Ce(Harene-triNOx)2 (1). Cyclic voltammetry of this compound showed stabilization of the tetravalent cerium cation with a Ce(IV/III) couple at E1/2 = -1.82 V versus Fc/Fc(+). On the basis of the uninvolvement of the third nitroxide group in the coordination chemistry with the cerium(IV) cation, the ligand system was redesigned toward a simpler bidentate mode, and a series of rare earth metal-arene-diNOx complexes were prepared with La(III), Ce(IV), Pr(III), Tb(III), and Y(III), [RE(arene-diNOx)2](-) ([2-RE](-), RE = La, Pr, Y, Tb) and Ce(IV)(arene-diNOx)2, where H2arene-diNOx = 1,3-bis(2'-tert-butylhydroxylaminoaryl)benzene. The core structures were isostructural throughout the series, with three nitroxide groups in η(2) binding modes and one κ(1) nitroxide group coordinated to the metal center in the solid state. In all cases except Ce(IV)(arene-diNOx)2, electrochemical analysis described two subsequent, ligand-based, quasi-reversible redox waves, indicating that a stable [N-O•] group was generated on the electrochemical time scale. Chemical oxidation of the terbium complex was performed, and isolation of the resulting complex, Tb(arene-diNOx)2·CH2Cl2 (3·CH2Cl2), confirmed the assignment of the cyclic voltammograms. Magnetic data showed no evidence of mixing between the Tb(III) states and the states of the open-shell ligand.

  14. Synthesis and Structures of A Series of Novel Rare Earth Transition Metal Sulfates

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Seven new rare earth transition metal sulfates were synthesized by hydrothermal reactions under conditions slightly above the critical point of water. Their crystal structures were determined from single crystal X-ray data. The compositions of the new compounds can be represented by two general formulae: REM(OH)3(SO4) and RE2M(OH)3(SO4)2F(H2O) with RE=Gd, Tb, Dy; M=Ni, Cu. Three different crystal structure types were found for the formula REM(OH)3(SO4). The structures of the new compounds all feature infinite chains of REOn coordination polyhedra, which are connected to chains of CuO6 or NiO6 octahedra. The limited size range of the rare earth cations observed in these compounds is most likely because of interactions between the octahedral chains and the chains of REOn polyhedra. The new compounds are closely related to the known yttrium transition metal sulfates.

  15. METALLIC PHASE AND INSULATING CHARACTER OF ALKALI-EARTH METAL DOPED C60

    Institute of Scientific and Technical Information of China (English)

    曹阳; 陈良进; 陈波; 冯建文; 陈文建

    1995-01-01

    The three dimensional EHMO crystal orbital calculations for crystalline Ba6 C60,Ca3 C60 and Ca5 C60 are reported.The ground state of partially doped Ca3 C60 is found to be insulating with an indrect energy gap of 0.5eV.In contrast,the Ca5 C60 forms a metallic conducting phase with a set of three half-filled bands crossing the Fermi level which is Found to locate close to a peak of the density of state. The character of crystal orbitals near the Fermilevel for both Ca3 C60 and Ca5 C60 is completely carbon-like.In both cases the Ca3 atoms are almost fully ionized and C60 molecules form a stable negative charge state with six to ten additional electrons.The conductivity of Ba6 C60 is resuted from the incomplete charge tranfer.The valance charge of every Ba ion is about 0.33.The total charge tranfer of six Ba atoms is almost the same as that of five Ca atoms.

  16. Earthshine observations at high spectral resolution: Exploring and detecting metal lines in the Earth's upper atmosphere

    CERN Document Server

    González-Merino, B; Motalebi, F; Montañés-Rodríguez, P; Kissler-Patig, M

    2013-01-01

    Observations of the Earth as a planet using the earthshine technique (i.e. looking at the light reflected from the darkside of the Moon), have been used for climate and astrobiology studies. They provide information about the planetary albedo, a fundamental parameter of the Earth's energy balance. Here we present for the first time, observations of the earthshine taken at high spectral resolution. The high spectral resolution was chosen in order to investigate the possibility of detecting metallic layers in the Earth's atmosphere of geological or meteoritic origin. The SARG echelle spectrograph at the Telescopio Nazionale Galileo in La Palma was used to acquire the earthshine data. Observations were carried out on several nights in February 2011, with the spectral resolution set at 29,000, covering a spectral range from the near-ultraviolet (360 nm) to near-infrared (1011.9 nm). While we find evidence for the detection of a Na layer in the earthshine, other atomic species are not detected, perhaps due to the ...

  17. The effects of alkaline dosage and Si/Al ratio on the immobilization of heavy metals in municipal solid waste incineration fly ash-based geopolymer.

    Science.gov (United States)

    Zheng, Lei; Wang, Wei; Shi, Yunchun

    2010-04-01

    The present research explored the application of geopolymerization for the immobilization and solidification of municipal solid waste incineration (MSWI) fly ash. The influence of alkaline activator dosage and Si/Al molar ratio on the compressive strength and microstructure of MSWI fly ash-based geopolymer was investigated. A geopolymer with the highest strength was identified to occur at an intermediate alkaline activator dosage and Si/Al ratio, and the optimal Na/MSWI fly ash and Si/Al molar ratio was close to 2.8 mol kg(-1) and 2.0, respectively. IR spectra showed that higher alkaline activator dosage enhanced the structural disruption of the original aluminosilicate phases and a higher degree of polymerization of the geopolymer networks. At low Si/Al ratio, there was an increasing number of tetrahedral Al incorporating into the silicate backbone. As the Na/MSWI fly ash ratio increased, the microstructure changed from containing large macropores to more mesopores and micropores, indicating that more geopolymers are formed. Furthermore, the pore volume distribution of geopolymers was observed to shift to larger pores as the Si/Al ratio increased, which suggests that the soluble silicon content serves to reduce the amount of geopolymers. Heavy metal leaching was successfully elucidated using the first-order reaction/reaction-diffusion model. Combining the results from the microstructure of samples with the kinetic analysis, the immobilization mechanism of Cr, Cu, and Zn was inferred in this study. The methodologies described could provide a powerful set of tools for the systematic evaluation of element release from geopolymers.

  18. Comparative studies on trace metal geochemistry in Indian and Chinese rivers

    Digital Repository Service at National Institute of Oceanography (India)

    Alagarsamy, R.; Zhang, J.

    concentration of Indian rivers (~300–1000 µg g–l) is higher than that of Chinese rivers (~150–300 µg g–l) and the global average (~170–350 µg g–l). Molar ratios of alkaline and alkaline earth metals to Fe and Al (i.e. segregation factor, SF) were calculated...

  19. Decomposition kinetics of alkaline earth carbonates by integral approximation method Cinética de decomposição de carbonatos de terra alcalina pelo método de aproximação integral

    Directory of Open Access Journals (Sweden)

    S. Maitra

    2008-09-01

    Full Text Available The decomposition kinetics of four synthetic alkaline earth metal carbonates (MgCO3, CaCO3, SrCO3 and BaCO3 was studied under non-isothermal conditions from thermo-gravimetric measurements as compared to. The integral approximation method of Coats and Redfern was used to determine the kinetic parameters for the decomposition processes. The decomposition reactions followed mostly first order kinetics and the activation energy of the decomposition reactions increased with the increase in the molecular mass of the carbonates. The change in enthalpy for the decomposition processes was also calculated and compared with the activation energies for the decomposition processes. The activation energy of the decomposition process for all the carbonates was higher than the enthalpy of the reaction excepting SrCO3.A cinética de decomposição de quatro carbonatos sintéticos de metais de terra alcalina (MgCO3, CaCO3, SrCO3 e BaCO3 foi estudada sob condições não isotérmicas por meio de medidas de termogravimétricas e feita sua comparação. O método de aproximação integral de Coats e Redfern foi usado para determinar os parâmetros cinéticos dos processos de decomposição. As reações de decomposição seguiram principalmente cinética de primeira ordem e a energia de ativação para as reações de decomposição aumentou com o aumento da massa molecular dos carbonatos. A variação na entalpia para os processos de decomposição foi também calculada e comparada com as energias de ativação. A energia de ativação dos processos de decomposição de todos os carbonatos foi maior que a entalpia da reação excepto para SrCO3.

  20. Metal-free N-doped carbon nanofibers as an efficient catalyst for oxygen reduction reactions in alkaline and acid media

    Science.gov (United States)

    Li, Ruchun; Shao, Xiaofeng; Li, Shuoshuo; Cheng, Pengpeng; Hu, Zhaoxia; Yuan, Dingsheng

    2016-12-01

    The development of metal-free catalysts to replace the use of Pt has played an important role in relation to its application to fuel cells. We report N-doped carbon nanofibers as the catalyst of an oxygen reduction reaction, which were synthesized via carbonizing bacterial cellulose-polypyrrole composites. The as-prepared material exhibited remarkable catalytic activity toward the oxygen reduction reaction with comparable onset potential and the ability to limit the current density of commercial Pt/C catalysts in both alkaline and acid media due to the unique porous three-dimensional network structure and the doped nitrogen atoms. The effect of N functionalities on catalytic behavior was systematically investigated. The results demonstrated that pyridinic-N was the dominating factor for catalytic performance toward the oxygen reduction reaction. Additionally, N-doped carbon nanofibers also demonstrated excellent cycling stability (93.2% and 89.4% retention of current density after chronoamperometry 20 000 s in alkaline and media, respectively), obviously superior to Pt/C.

  1. Tidal Downsizing Model. III. Planets from sub-Earths to Brown Dwarfs: structure and metallicity preferences

    CERN Document Server

    Nayakshin, Sergei

    2015-01-01

    We present improved population synthesis calculations in the context of the Tidal Downsizing (TD) hypothesis for planet formation. Our models provide natural explanations and/or quantitative match to exoplanet observations in the following categories: (i) most abundant planets being super-Earths; (ii) cores more massive than $\\sim 5-15 M_\\oplus$ are enveloped by massive metal-rich atmospheres; (iii) the frequency of occurrence of close-in gas giant planets correlates strongly with metallicity of the host star; (iv) no such correlation is found for sub-Neptune planets; (v) presence of massive cores in giant planets; (vi) the composition of gas giant planets is over-abundant in metals compared to their host stars; (vii) this over-abundance decreases with planet's mass, as observed; (viii) a deep valley in the planet mass function between masses of $\\sim 10-20 M_\\oplus$ and $\\sim 100 M_\\oplus$. We provide a number of observational predictions distinguishing the model from Core Accretion: (a) composition of the m...

  2. Facilitated alkali ion transfer at the water 1,2-dichloroethane interphase Ab-initio calculations concerning alkaline metal cation - 1,10-phenanthroline complexes

    CERN Document Server

    Sánchez, C; Baruzzi, A M; Leiva, E P M

    1997-01-01

    A series of calculations on the energetics of complexation of alkaline metals with 1,10-phenanthroline are presented. It is an experimental fact that the ordering of the free energy of transfer across the water - 1,2-dichloroethane interphase is governed by the charge / size ratio of the diferent cations; the larger cations showing the lower free energy of transfer. This ordering of the free energies of transfer is reverted in the presence of 1,10-phenanthroline in the organic phase. We have devised a thermodynamic cycle for the transfer process and by means of ab-initio calculations have drawn the conclusion that in the presence of phen the free energy of transfer is governed by the stability of the PHEN/M $^{+}$complex, which explains the observed tendency from a theoretical point of view.

  3. Technique for recovering rare-earth metals from spent sintered Nd-Fe-B magnets without external heating

    Directory of Open Access Journals (Sweden)

    Ryo Sasai

    2016-06-01

    Full Text Available To selectively recover rare-earth metals with higher purity from spent sintered Nd-Fe-B magnets without external heating, we investigated the mechano-chemical treatment of spent sintered Nd-Fe-B magnet powder with a reaction solution of HCl and (COOH2 at room temperature. The results of various experiments showed that the mechano-chemical treatment with HCl and (COOH2 is very effective for recovering the rare-earth metals contained in spent sintered Nd-Fe-B magnet powder; the recovery rate and purity of the rare-earth metals were 95.3 and 95.0 mass%, respectively, under optimal conditions ([HCl] = 0.2 mol/dm3 and [(COOH2] = 0.25 mol/dm3.

  4. Uptake of nickel from 316L stainless steel into contacting osteoblastic cells and metal ion interference with BMP-2-induced alkaline phosphatase.

    Science.gov (United States)

    Mölders, Martina; Felix, Joachim; Bingmann, Dieter; Hirner, Alfred; Wiemann, Martin

    2007-11-01

    Bone cells contacting nickel (Ni)-containing implant materials may be affected by Ni species via disturbed signaling pathways involved in bone cell development. Here we analyze effects of the Ni-containing steel 316L and major metal constituents thereof on bone morphogenetic protein-2 (BMP-2)-induced alkaline phosphatase (ALP) of MC3T3-E1 cells. While cells grew normally on 316L, cellular Ni content increased 10-fold vs. control within 4 days. With respect to the major components of 316L, Ni2+ (3-50 microM) was most inhibitory to BMP-2-induced ALP, whereas even 50 microM Fe3+, Cr3+, Mo5+, or Mn2+ had no such effect. In line with this, BMP-2-induced ALP was significantly reduced in cells on 316L. This effect was not prevented by the metal ion chelator diethylenetriaminepentaacetic acid (DTPA). Instead, DTPA abolished the stimulatory effect of BMP-2 on ALP, pointing to chelatable metal ions involved. Zn2+, as one possible candidate, antagonized the Ni2+ inhibition of BMP-2-induced ALP in both MC3T3-E1 and human bone marrow stromal cells. Results show that cells contacting 316L steel are exposed to increased concentrations of Ni which suffice to impair BMP-2-induced ALP activity. Zn2+, as a competitor of this inhibition, may help to restore normal osteoblastic function and bone development under these conditions.

  5. NLO in correlation of phase transition and the alkaline metal environment effect on it in KDP family

    Energy Technology Data Exchange (ETDEWEB)

    Ennaceur, Nasreddine, E-mail: nasr.ennaceur@yahoo.fr [Laboratoire Physico-chimie de l' État Solide, Faculté des Sciences, Université de Sfax, BP 1171, 3000 (Tunisia); Laboratoire de Photonique Quantique et Moléculaire Institut d’Alembert—École Normale Supérieure, 61 avenue du Président Wilson, 94230 Cachan (France); Ledoux-Rak, Isabelle; Singh, Anu [Laboratoire de Photonique Quantique et Moléculaire Institut d’Alembert—École Normale Supérieure, 61 avenue du Président Wilson, 94230 Cachan (France); Mhiri, Tahar; Jarraya, Khaled [Laboratoire Physico-chimie de l' État Solide, Faculté des Sciences, Université de Sfax, BP 1171, 3000 (Tunisia)

    2013-11-01

    The NaH{sub 2}(P{sub 0.48}As{sub 0.52})O{sub 4}·H{sub 2}O (NDAP) compounds allow favorable conditions to the study of evolution of the NLO response during the non-centrosymmetry phases transitions. In fact, NDAP shows the existence of three reversible non-centrosymmetry phase transitions between 272 and 313 K. These experiments are good tools for probing phase transitions and their nature. In this process, several experiments are useful to reveal not only an agreement between the thermal and the quadratic nonlinear (NLO) studies, but also an attempt amongst other things to correlate the probable effect of the alkaline environment of the KDP family on the effectiveness of the NLO intensity.

  6. Syntheses, Vibrational Spectroscopy, and Crystal Structure Determination from X-Ray Powder Diffraction Data of Alkaline Earth Dicyanamides M[N(CN) 2] 2 with M=Mg, Ca, Sr, and Ba

    Science.gov (United States)

    Jürgens, Barbara; Irran, Elisabeth; Schnick, Wolfgang

    2001-03-01

    The alkaline earth dicyanamides Mg[N(CN)2]2, Ca[N(CN)2]2, Sr[N(CN)2]2, and Ba[N(CN)2]2 were synthesized by ion exchange using Na[N(CN)2] and the respective nitrates or bromides as starting materials. The crystal structures were determined from X-ray powder diffractometry: Mg[N(CN)2]2, Pnnm, Z=2, a=617.14(3), b=716.97(3), and c=740.35(5) pm; Ca[N(CN)2]2 and Sr[N(CN)2]2, C2/c, Z=4; Ca[N(CN)2]2, a=1244.55(3), b=607.97(1), and c=789.81(1) pm, β=98.864(2)°; Sr[N(CN)2]2, a=1279.63(2), b=624.756(8), and c=817.56(1) pm, β=99.787(1)°; Ba[N(CN)2]2, Pnma, Z=4, a=1368.68(7), b=429.07(7), and c=1226.26(2) pm. The dicyanamides consist of the respective alkaline earth cations and bent planar [N(CN)2]- ions. The structural features were correlated with vibrational spectroscopic data. The thermal behavior was studied by thermoanalytical experiments.

  7. Liquid-liquid extraction and separation of total rare earth (RE) metals from polymetallic manganese nodule leaching solution

    Institute of Scientific and Technical Information of China (English)

    PK Parhi; KH Park; CW Nam; JT Park

    2015-01-01

    The study on the solvent extraction for quantitative and selective separation of total rare earth metals from the polymetallic nodule leach liquor was investigated. The typical leach liquor bearing 0. 094 g/L total rare earth, 0. 23 g/L Mn, 0.697 g/L Cu, 0.2 g/L Fe, 0.01 g/L Co and 0.735 g/L Ni was subjected to the removal iron content by precipitation method using Ca(OH)2 at pH 3.95, prior to solvent extraction of rare earth metals. Three different organo-phosphoric acid reagents (D2EHPA, PC88A, Cyanex 272) were used to ascertain their performances and selectivity towards the loading of rare earth metals in presence of other base metals. Based on the results of eq. pH effect, the performances of above three extractants followed the order as:D2EHPA>PC88A>Cyanex 272. To ensure the absence of extraction of base metals (Cu, Co, Ni), the eq. pH of the solution was optimized at the level of 2.21, though higher rare earth metal extraction efficiency was observed at higher eq. pH with either of the extractants. The complete process flow diagram for substantial recovery of total rare earth was developed using D2EHPA. Extraction isotherm plot was constructed at A:O=12:1, 3-stages and pHe=2.21, using 0.8 mol/L D2EHPA and the predicted condition of this study was further confirmed by 6-Cycles Counter Current Simulation (CCS) study. The stripping of total rare earth from loaded organic phase (LO) was conducted using HCl solution. Mc-Cabe Thiele diagram study carried out at A:O=1:5 using 4 mol/L HCl showed that three theoretical stages were needed for quantitative stripping of total rare earth. The subsequent stripped solution resulted thus led to contain total rare earth of 5.6 g/L indicating a very high enrichment of total metals by solvent extraction (SX) process.

  8. New Rare Earth Element Abundance Distributions for the Sun and Five r-Process-Rich Very Metal-Poor Stars

    CERN Document Server

    Sneden, Christopher; Cowan, John J; Ivans, Inese I; Hartog, Elizabeth A Den

    2009-01-01

    We have derived new abundances of the rare-earth elements Pr, Dy, Tm, Yb, and Lu for the solar photosphere and for five very metal-poor, neutron-capture r-process-rich giant stars. The photospheric values for all five elements are in good agreement with meteoritic abundances. For the low metallicity sample, these abundances have been combined with new Ce abundances from a companion paper, and reconsideration of a few other elements in individual stars, to produce internally-consistent Ba, rare-earth, and Hf (56<= Z <= 72) element distributions. These have been used in a critical comparison between stellar and solar r-process abundance mixes.

  9. Structures of rare earth-transition metal rich compounds derived from CaCu5 type

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The properties of materials have a close connect ion to their crystal structures. Rare earth (R)-transition metal (T) rich compo und are the focus of investigation in the search for new hard magnetic materials . As the basis for the study of stabilized effect of the third component on the fo rmation of RT5 derivative and its influence of the occupied sites on magnetic properties, in this paper, the possible derivative compounds based on the RT5 primitive unit cell of the CaCu5 structure type formed through the ordered or disordered substitution of dumbbell pair 2T atoms for the R atoms at some sit es, and the structural relationship between the derivatives and the prototype ar e summarized.

  10. Magnetic ordering temperatures in rare earth metal dysprosium under ultrahigh pressures

    Science.gov (United States)

    Samudrala, Gopi K.; Tsoi, Georgiy M.; Weir, Samuel T.; Vohra, Yogesh K.

    2014-04-01

    Magnetic ordering temperatures in heavy rare earth metal dysprosium (Dy) have been studied using an ultrasensitive electrical transport measurement technique in a designer diamond anvil cell to a pressure of 69 GPa and a temperature of 10 K. Previous studies using magnetic susceptibility measurements at high pressures were able to track magnetic ordering temperature only till 7 GPa in the hexagonal close packed (hcp) phase of Dy. Our studies indicate that the magnetic ordering temperature shows an abrupt drop of 80 K at the hcp-Sm phase transition followed by a gradual decrease that continues till 17 GPa. This is followed by a rapid increase in the magnetic ordering temperatures in the double hcp phase and finally leveling off in the distorted face centered cubic phase of Dy. Our studies reaffirm that 4f-shell remains localized in Dy and there is no loss of magnetic moment or 4f-shell delocalization for pressures up to 69 GPa.

  11. Thermodynamics analysis of the rare earth metals and their alloys with indium in solid state

    Energy Technology Data Exchange (ETDEWEB)

    Vassiliev, V.P., E-mail: valeryvassiliev@yahoo.fr [Chemical Department, Lomonossov University, Moscow 119992 (Russian Federation); Benaissa, Ablazeze [Département des Matériaux, Faculté des Sciences de l’Ingénieur, Université M’hamed Bougara, Boumerdes 35000 (Algeria); Taldrik, A.F. [Institute of Superconductivity and Solid State Physics, Academician Kurchatov 1, Moscow 123098 (Russian Federation)

    2013-09-25

    Graphical abstract: Gibbs energies of formation vs. RE atomic numbers in REIn{sub 3}. Highlights: •Set of experimental values was collected for REIn{sub 3} phases. •Thermodynamic functions of formation were calculated at 298 K and 775 K. •Experimental and calculated values were compared. -- Abstract: Nonlinear correlative analyses between thermodynamic and some physico-chemical properties of rare-earth metals (RE) and their alloys with indium are performed for the isostructural phases RE and REIn{sub 3}. The thermodynamics values (Gibbs energies of formation, enthalpies of formation, and entropies of formation at 298 K and 775 K and standard entropies) of LnIn{sub 3} phases are calculated on the basis of calorimetry and potentiometry results. The proposed correlation between physico-chemical and thermodynamic properties agrees for all the isostructural phases REX (X are others elements of the periodic table). The resulting thermodynamic data are recommended for metallurgical handbook.

  12. Influence of selected rare earth metals on structural characteristics of 42CrMo4 steel

    Directory of Open Access Journals (Sweden)

    J. Drápala

    2016-10-01

    Full Text Available The influence of rare earth metals (REM addition on solidification structure of the low-carbon 42CrMo4 steel was investigated. Alloys were prepared by means of a centrifugal casting. The addition of cerium, praseodymium or mischmetal in the steel produced greatly improved solidification structure with a suppressed columnar grain zone, finer grain size in the equiaxed grain zone. The additions occurred in the steel bath in the form of REM oxide and/or oxide-sulphide inclusions and as dissolved REM segregated along with other elements at prior grain boundaries and interdendritic spaces. Microstructure (light microscope, SEM/EDX chemical microanalysis, and TOF-SIMS analysis – mapping of elements in the structure of alloys were obtained.

  13. Theory of Temperature Dependence of the Magnetization in Rare-Earth-Transition-Metal Alloys

    DEFF Research Database (Denmark)

    Szpunar, B.; Lindgård, Per-Anker

    1977-01-01

    It is shown that the temperature dependence of the magnetic moments and Curie and ferrimagnetic compensation temperatures for Gdl-xTx (T = Co, Ni, and Fe) and Y1-xCox can be accounted for by a simple model assuming a RKKY interaction between the rare-earth moments and the transition-metal pseudo-spin......1-xCox durch ein einfaches Model1 erklärt werden können, das eine RKKY-Wechsel-wirkung zwischen den Momenten der Seltenen Erden und des Pseudo-Spins des Übergangsmetalls annimmt. Die Wechselwirkung wird durch ein effektives Legierungsmedium übermittelt, das mit der CPA-Theorie und elliptischen...

  14. Spin-orbit qubits of rare-earth-metal ions in axially symmetric crystal fields.

    Science.gov (United States)

    Bertaina, S; Shim, J H; Gambarelli, S; Malkin, B Z; Barbara, B

    2009-11-27

    Contrary to the well-known spin qubits, rare-earth-metal qubits are characterized by a strong influence of crystal field due to large spin-orbit coupling. At low temperature and in the presence of resonance microwaves, it is the magnetic moment of the crystal-field ground state which nutates (for several micros) and the Rabi frequency Omega(R) is anisotropic. Here, we present a study of the variations of Omega(R)(H(0)) with the magnitude and direction of the static magnetic field H(0) for the odd 167Er isotope in a single crystal CaWO(4):Er(3+). The hyperfine interactions split the Omega(R)(H(0)) curve into eight different curves which are fitted numerically and described analytically. These "spin-orbit qubits" should allow detailed studies of decoherence mechanisms which become relevant at high temperature and open new ways for qubit addressing using properly oriented magnetic fields.

  15. Metal Borohydrides synthesized from metal borides and metal hydrides

    DEFF Research Database (Denmark)

    Sommer, Sanna

    2014-01-01

    and Ca(BH4)2, respectively [3,4]. An attempt to synthesize alkali and alkaline earth metal borohydrides from various borides by ball milling under high hydrogen pressure is presented here. MgB2, AlB2 and CaB6 have been milled with MHx (M = Li, Na, Mg, Ca) at p(H2) = 110 bar for 24 hours. All samples were...

  16. The Importance of Rare-Earth Additions in Zr-Based AB2 Metal Hydride Alloys

    Directory of Open Access Journals (Sweden)

    Kwo-Hsiung Young

    2016-07-01

    Full Text Available Effects of substitutions of rare earth (RE elements (Y, La, Ce, and Nd to the Zr-based AB2 multi-phase metal hydride (MH alloys on the structure, gaseous phase hydrogen storage (H-storage, and electrochemical properties were studied and compared. Solubilities of the RE atoms in the main Laves phases (C14 and C15 are very low, and therefore the main contributions of the RE additives are through the formation of the RENi phase and change in TiNi phase abundance. Both the RENi and TiNi phases are found to facilitate the bulk diffusion of hydrogen but impede the surface reaction. The former is very effective in improving the activation behaviors. −40 °C performances of the Ce-doped alloys are slightly better than the Nd-doped alloys but not as good as those of the La-doped alloys, which gained the improvement through a different mechanism. While the improvement in ultra-low-temperature performance of the Ce-containing alloys can be associated with a larger amount of metallic Ni-clusters embedded in the surface oxide, the improvement in the La-containing alloys originates from the clean alloy/oxide interface as shown in an earlier transmission electron microscopy study. Overall, the substitution of 1 at% Ce to partially replace Zr gives the best electrochemical performances (capacity, rate, and activation and is recommended for all the AB2 MH alloys for electrochemical applications.

  17. pH-metric and thermodynamic studies of rare earth metal chelates

    Institute of Scientific and Technical Information of China (English)

    Alok Vyas; R. P. Mathur

    2009-01-01

    Proton ligand stability constants of hydroxybenzoic acid containing nitro group (2-Hydroxy-4-nitrobenzoic acid and 3-Hydroxy-4-nitrobenzoic acid) were determined through Irving-Rossoti pH titration technique. The stability constants of rare earth metal chelates con-taining 2-Hydroxy-4-nitrobenzoic acid and 3-Hydroxy-4-nitrobenzoic acid as ligands were studied in aqueous medium at different ionic strength (μ=0.01, 0.05 and 0.1 mol/L) and temperatures (298, 308 and 318±0.1 K). The values of stability constant were evaluated through different computational methods like successive approximation, least square treatment, correction term method, and convergence method. The observed value of thermodynamic parameters (△G°, △H° and △S°) favors the complex formation between metal and ligands. The order of stability constant was found to be Pr(Ⅲ)

  18. Decoration of Micro-/Nanoscale Noble Metal Particles on 3D Porous Nickel Using Electrodeposition Technique as Electrocatalyst for Hydrogen Evolution Reaction in Alkaline Electrolyte.

    Science.gov (United States)

    Qian, Xin; Hang, Tao; Shanmugam, Sangaraju; Li, Ming

    2015-07-29

    Micro-/nanoscale noble metal (Ag, Au, and Pt) particle-decorated 3D porous nickel electrodes for hydrogen evolution reaction (HER) in alkaline electrolyte are fabricated via galvanostatic electrodeposition technique. The developed electrodes are characterized by field emission scanning electron microscopy and electrochemical measurements including Tafel polarization curves, cyclic voltammetry, and electrochemical impedance spectroscopy. It is clearly shown that the enlarged real surface area caused by 3D highly porous dendritic structure has greatly reinforced the electrocatalytic activity toward HER. Comparative analysis of electrodeposited Ag, Au, and Pt particle-decorated porous nickel electrodes for HER indicates that both intrinsic property and size of the noble metal particles can lead to distinct catalytic activities. Both nanoscale Au and Pt particles have further reinforcement effect toward HER, whereas microscale Ag particles exhibit the reverse effect. As an effective 3D hydrogen evolution cathode, the nanoscale Pt-particle-decorated 3D porous nickel electrode demonstrates the highest catalytic activity with an extremely low overpotential of -0.045 V for hydrogen production, a considerable exchange current density of 9.47 mA cm(-2) at 25 °C, and high durability in long-term electrolysis, all of which are attributed to the intrinsic catalytic property and the extremely small size of Pt particles.

  19. Heterogeneous Earth Accretion and Incomplete Metal-Silicate Reequilibration at High Pressure During Core Formation

    Science.gov (United States)

    Rubie, D. C.; Mann, U.; Frost, D. J.; Kegler, P.; Holzheid, A.; Palme, H.

    2007-12-01

    We present a new model of core formation, based on the partitioning of siderophile elements, that involves accreting the Earth through a series of collisions with smaller bodies that had already differentiated at low pressure. Each impact results in a magma ocean in which the core of the impactor reequilibrates with silicate liquid at high pressure before merging with the Earth's protocore. The oxygen contents of the chondritic compositions of the proto-Earth and impactors can be varied. The compositions of coexisting metal and silicate are determined through mass balance combined with partitioning equations for Ni, FeO, Si and other siderophile elements. The oxygen fugacity is fixed by the partitioning of FeO and is a function of P, T and bulk oxygen content. An important constraint for core formation is that core-mantle partition coefficients for Ni and Co must both converge to values of 23-28. Based on a recent study of the partitioning of Ni and Co over a wide P-T range (Kegler et al., EPSL, submitted) together with other published data, this constraint is not satisfied by a single- stage core formation model at any conditions because the partition coefficients converge at values that are much too low. In the present multi-stage model, the correct values can be reached if only part of each impactor core reequilibrates with silicate liquid in the magma ocean (as proposed by previous models based on Hf-W isotope studies). Physically, this would mean that impactor cores fail to emulsify completely as they sink through the magma ocean. Incorporating other elements (e.g. V and Cr) in the model requires, in addition, that the bulk composition of the impactors changes during accretion from reduced (FeO-poor) to oxidised FeO-rich). Then, with the resulting increase in fO2, incomplete reequilibration of the cores during the final 20-30% of Earth accretion is required to satisfy the Ni-Co constraint. In addition, this model enables the concentrations of O and Si in the

  20. Effects of rare earth oxide on hardfacing metal microstructure of medium carbon steel and its refinement mechanism

    Institute of Scientific and Technical Information of China (English)

    HAO Feifei; LIAO Bo; LI Da; LIU Ligang; DAN Ting; REN Xuejun; YANG Qingxiang

    2011-01-01

    The electrodes for hardfacing medium carbon steel with six additions of rare earth oxide were developed in this work. By means of optical microscopy and scanning electron microscopy, the microstructure, inclusion and the fractograph of the hardfacing metal were observed. Then, the effects of rare earth oxide on microstructure and inclusions in hardfacing metal were analyzed. The effectiveness of rare earth oxide as heterogeneous nuclei of δ-Fe was calculated with the misfit theory. The results showed that, the microstructure of hardfacing metal was composed of ferrite and small amount of pearlite. The microstructure was refined at first and then coarsened with the increase of rare earth oxide addition. The fractograph was changed from brittle to equiaxed dimples, then became quasi-cleavage and cleavage gradually.The calculated results showed that, the ferrite grain size could be refined because that LaA1O3 as heterogeneous nuclei ofδ-Fe was moderately effective, and the ferrite grain size was coarsened because the misfits between Ce2O3 and δ-Fe, Ce2O2S and δ-Fe were increased with futher increase of rare earth oxide addition.

  1. Silylation of C-H bonds in aromatic heterocycles by an Earth-abundant metal catalyst

    Science.gov (United States)

    Toutov, Anton A.; Liu, Wen-Bo; Betz, Kerry N.; Fedorov, Alexey; Stoltz, Brian M.; Grubbs, Robert H.

    2015-02-01

    Heteroaromatic compounds containing carbon-silicon (C-Si) bonds are of great interest in the fields of organic electronics and photonics, drug discovery, nuclear medicine and complex molecule synthesis, because these compounds have very useful physicochemical properties. Many of the methods now used to construct heteroaromatic C-Si bonds involve stoichiometric reactions between heteroaryl organometallic species and silicon electrophiles or direct, transition-metal-catalysed intermolecular carbon-hydrogen (C-H) silylation using rhodium or iridium complexes in the presence of excess hydrogen acceptors. Both approaches are useful, but their limitations include functional group incompatibility, narrow scope of application, high cost and low availability of the catalysts, and unproven scalability. For this reason, a new and general catalytic approach to heteroaromatic C-Si bond construction that avoids such limitations is highly desirable. Here we report an example of cross-dehydrogenative heteroaromatic C-H functionalization catalysed by an Earth-abundant alkali metal species. We found that readily available and inexpensive potassium tert-butoxide catalyses the direct silylation of aromatic heterocycles with hydrosilanes, furnishing heteroarylsilanes in a single step. The silylation proceeds under mild conditions, in the absence of hydrogen acceptors, ligands or additives, and is scalable to greater than 100 grams under optionally solvent-free conditions. Substrate classes that are difficult to activate with precious metal catalysts are silylated in good yield and with excellent regioselectivity. The derived heteroarylsilane products readily engage in versatile transformations enabling new synthetic strategies for heteroaromatic elaboration, and are useful in their own right in pharmaceutical and materials science applications.

  2. Dynamic polarizabilities of rare-earth-metal atoms and dispersion coefficients for their interaction with helium atoms

    NARCIS (Netherlands)

    Chu, X.; Dalgarno, A.; Groenenboom, G.C.

    2007-01-01

    The dynamic scalar and tensor polarizabilities of the rare-earth-metal atoms are calculated with time-dependent density functional theory. The frequency-dependent polarizabilities at imaginary frequencies are used to determine the isotropic and orientation-dependent van der Waals coefficients for th

  3. Distribution of Sb, As, Ge, and In between metal and silicate during accretion and core formation in the Earth

    Science.gov (United States)

    Righter, K.; Nickodem, K.; Pando, K.; Danielson, L.; Boujibar, A.; Righter, M.; Lapen, T. J.

    2017-02-01

    A large number of siderophile (iron-loving) elements are also volatile, thus offering constraints on the origin of volatile elements in differentiated bodies such as Earth, Moon, Mars and Vesta. Metal-silicate partitioning data for many of these elements is lacking, making their overall mantle concentrations in these bodies difficult to model and origin difficult to distinguish between core formation and volatile depletion. To address this gap in understanding, we have undertaken systematic studies of four volatile siderophile elements - Sb, As, Ge and In - at variable temperature and variable Si content of metal. Several series were carried out at 1 GPa, and between 1500 and 1900 °C, for both C saturated and C-free conditions. The results show that temperature causes a decrease in the metal/silicate partition coefficient for all four elements. In addition, activity coefficients for each element have been determined and show a very strong dependence on Si content of Fe alloy. Si dissolved in metal significantly decreases the metal/silicate partition coefficients, at both 1600 and 1800 °C. The combination of temperature and Si content of the metal causes reduction of the metal-silicate partition coefficient to values that are close to those required for an origin of mantle As, Sb, Ge, and In concentrations by metal-silicate equilibrium processes. Combining these new results with previous studies on As, Sb, Ge, and In, allowed derivation of predictive expressions for metal/silicate partition coefficients for these elements which can then be applied to Earth. The expressions are applied to two scenarios for continuous accretion of Earth; specifically for constant and increasing fO2 during accretion. The results indicate that mantle concentrations of As, Sb, Ge, and In can be explained by metal-silicate equilibrium during an accretion scenario. The modeling is not especially sensitive to either scenario, although all element concentrations are explained better by a

  4. Metal loading effect on rare earth element binding to humic acid: Experimental and modelling evidence

    Science.gov (United States)

    Marsac, Rémi; Davranche, Mélanie; Gruau, Gérard; Dia, Aline

    2010-03-01

    The effect of metal loading on the binding of rare earth elements (REE) to humic acid (HA) was studied by combining ultrafiltration and Inductively Coupled Plasma Mass Spectrometry techniques. REE-HA complexation experiments were performed at pH 3 for REE/C molar ratios ranging from ca 4 × 10 -4 to 2.7 × 10 -2. Results show that the relative amount of REE bound to HA strongly increases with decreasing REE/C. A middle-REE (MREE) downward concavity is shown by patterns at high metal loading, whereas patterns at low metal loading display a regular increase from La to Lu. Humic Ion Model VI modelling are close to the experimental data variations, provided that (i) the ΔLK 2 parameter (i.e. the Model VI parameter taken into account the presence of strong but low density binding sites) is allowed to increase regularly from La to Lu (from 1.1 to 2.1) and (ii) the published log KMA values (i.e. the REE-HA binding constants specific to Model VI) are slightly modified, in particular with respect to heavy REE. Modelling approach provided evidence that logKdREE patterns with varying REE/C likely arises because REE binding to HA occurs through two types of binding sites in different density: (i) a few strong sites that preferentially complex the heavy REE and thus control the logKdREE atterns at low REE/C; (ii) a larger amount of weaker binding sites that preferentially complex the middle-REE and thus control the logKdREE pattern at high REE/C. Hence, metal loading exerts a major effect on HA-mediated REE binding, which could explain the diversity of published conditional constants for REE binding with HA. A literature survey suggests that the few strong sites activated at low REE/C could be multidentate carboxylic sites, or perhaps N-, or P-functional groups. Finally, an examination of the literature field data proposed that the described loading effect could account for much of the variation in REE patterns observed in natural organic-rich waters (DOC > 5 mg L -1 and 4

  5. Synthesis and characterization of anhydrous rare earth metal nitrates, rare earth acetates and rare earth oxyacetates; Synthese und Charakterisierung wasserfreier Seltenerdmetall-Nitrate, -Acetate und -Oxyacetate

    Energy Technology Data Exchange (ETDEWEB)

    Heinrichs, Christina

    2013-10-29

    Anhydrous rare-earth metal (RE) nitrates, RE nitrate monohydrates and RE acetates were synthesized by thermal dehydration of RE nitrate hydrates and RE acetate hydrates in an argon flow or vacuum. RE oxyacetates were synthesized by thermal decomposition of RE acetates. Furthermore praseodymium carbonate hydroxide was synthesized by heating Pr carbonate hydrate. The compounds were analyzed by X-ray powder diffraction and, for selected examples, measurements with high-resolution synchrotron radiation were performed. Three new crystal structure types were found for RE nitrates: RE(NO{sub 3}){sub 3} with RE = La - Sm (type I) crystallize monoclinically in space group C2/c with Z = 16 (CN = 12, 11). RE(NO{sub 3}){sub 3} with RE = Y, Eu - Yb (type II) crystallize monoclinically in space group P2{sub 1}/c with Z = 4 (CN = 10) and Lu(NO{sub 3}){sub 3} (type III) monoclinically in space group I2/a with Z = 16 (CN = 8, 7). With decreasing CN (coordination number) a structural trend within the RE nitrates is observed: The RE nitrates of type I with the largest RE{sup 3+} cations build a three-dimensional network, the RE nitrates of type II form close packed layers and the preliminary structural model of Lu(NO{sub 3}){sub 3} (type III) with the smallest RE{sup 3+} cation shows layers and chains. The product of the dehydration of Sc(NO{sub 3}){sub 3} . n H{sub 2}O was indexed monoclinically in space group P2{sub 1}/c. Monohydrates RE(NO{sub 3}){sub 3} . H{sub 2}O with RE = Dy - Yb crystallize isotypically with Y(NO{sub 3}){sub 3} . H{sub 2}O in the triclinic space group P anti 1 with Z = 2 (CN = 9). Pr(CH{sub 3}CO{sub 2}){sub 3} does not crystallize in the known Pr acetate type but in the trigonal space group R anti 3 with Z = 18 (CN = 10) isotypically with the La acetate type which was only known for La(CH{sub 3}CO{sub 2}){sub 3} and Ce(CH{sub 3}CO{sub 2}){sub 3} up to now. In addition to the known Ho acetate type a new crystal structure type (Ho acetate type II) was found for

  6. Synthesis and structural diversity of trivalent rare-earth metal diisopropylamide complexes.

    Science.gov (United States)

    Spallek, Tatiana; Heß, Oliver; Meermann-Zimmermann, Melanie; Meermann, Christian; Klimpel, Michael G; Estler, Frank; Schneider, David; Scherer, Wolfgang; Tafipolsky, Maxim; Törnroos, Karl W; Maichle-Mössmer, Cäcilia; Sirsch, Peter; Anwander, Reiner

    2016-09-21

    A series of rare-earth metal diisopropylamide complexes has been obtained via salt metathesis employing LnCl3(THF)x and lithium (LDA) or sodium diisopropylamide (NDA) in n-hexane. Reactions with AM : Ln ratios ≥3 gave ate complexes (AM)Ln(NiPr2)4(THF)n (n = 1, 2; Ln = Sc, Y, La, Lu; AM = Li, Na) in good yields. For smaller rare-earth metal centres such as scandium and lutetium, a Li : Ln ratio = 2.5 accomplished ate-free tris(amido) complexes Ln(NiPr2)3(THF). The chloro-bridged dimeric derivatives [Ln(NiPr2)2(μ-Cl)(THF)]2 (Ln = Sc, Y, La, Lu) could be obtained in high yields for Li : Ln = 1.6-2. The product resulting from the Li : La = 1 : 1.6 reaction revealed a crystal structure containing two different molecules in the crystal lattice, [La(NiPr2)2(THF)(μ-Cl)]2·La(NiPr2)3(THF)2. Recrystallization of the chloro-bridged dimers led to the formation of the monomeric species Ln(NiPr2)2Cl(THF)2 (Ln = Sc, Lu) and La(NiPr2)3(THF)2. The reaction of YCl3 and LDA with Li : Y = 2 in the absence of THF gave a bimetallic ate complex LiY(NiPr2)4 with a chain-like structure. For scandium, the equimolar reactions with LDA or NDA yielded crystals of tetrametallic mono(amido) species, {[Sc(NiPr2)Cl2(THF)]2(LiCl)}2 and [Sc(NiPr2)Cl2(THF)]4, respectively. Depending on the Ln(iii) size, AM, and presence of a donor solvent, ate complexes (AM)Ln(NiPr2)4(THF)n show distinct dynamic behaviour as revealed by variable temperature NMR spectroscopy. The presence of weak LnCH(iPr) β-agostic interactions, as indicated by Ln-N-C angles <105°, is corroborated by DFT calculations and NBO analysis.

  7. Quantum mechanical study of molecular collisions at ultra-low energy: applications to alkali and alkaline-earth systems; Etude quantique de collisions moleculaires a ultra-basse energie: applications aux alcalins et alcalino-terreux

    Energy Technology Data Exchange (ETDEWEB)

    Quemener, G

    2006-10-15

    In order to investigate the collisional processes which occur during the formation of molecular Bose-Einstein condensates, a time-independent quantum mechanical formalism, based on hyperspherical coordinates, has been applied to the study of atom-diatom dynamics at ultra-low energies. We present theoretical results for three alkali systems, each composed of lithium, sodium or potassium atoms, and for an alkaline-earth system composed of calcium atoms. We also study dynamics at large and positive atom-atom scattering length. Evidence for the suppression of inelastic processes in a fermionic system is given, as well as a linear relation between the atom-diatom scattering length and the atom-atom scattering length. (author)

  8. Effect of alkaline earth oxides on the physical and spectroscopic properties of Dy3+- doped Li2O-B2O3 glasses for white emitting material application

    Science.gov (United States)

    Shamshad, L.; Rooh, G.; Kirdsiri, K.; Srisittipokakun, N.; Damdee, B.; Kim, H. J.; Kaewkhao, J.

    2017-02-01

    Li2O-MO-B2O3:0.5Dy2O3 glasses mixed with four different alkaline earth modifier oxides MgO, CaO, SrO and BaO were synthesized by melt quench technique. Their physical properties like density, molar volume and refractive index were measured at room temperature and the effect of alkaline earth modifier oxides were studied. Also, optical absorption and photoluminescence spectra of these glasses have been acquired at room temperature. The Judd-Ofelt theory was effectively used to characterize these spectra and spectral intensities (ƒcal), Judd-Ofelt intensity parameters (Ω2, Ω4 and Ω6) and certain radiative properties have been determined. Radiative life-times (τR), branching ratios (βcal), and emission cross-sections (σp) and optical gain parameters (σp × τR) were calculated from the Judd-Ofelt intensity parameters and the variation in these parameters with the variation of glass matrix are discussed. Yellow/Blue (Y/B) ratio and chromacity color coordinates (x,y) are calculated from the emission spectra which indicates the white light generation from all the investigated samples. The correlated color temperature (CCT) for the studied glasses is found to be 4418 K. The fluorescence decay time (τexp) of the 4F9/2 level of Dy3+ has been measured from the decay profiles and compared with calculated lifetimes (τcal). Among all the studied glass matrices, the glass containing BaO exhibits high value of branching ratio, large emission cross-section and high optical gain parameter for 6F9/2 → 6H13 at 575 nm. The results indicates the suitability of all the studied glasses for laser action and white light generation.

  9. Synthesis of rare earth metal-organic frameworks (Ln-MOFs) and their properties of adsorption desulfurization

    Institute of Scientific and Technical Information of China (English)

    刘想; 王景艳; 李庆远; 蒋赛; 张天浩; 季生福

    2014-01-01

    The rare earth metal-organic frameworks (Ln-MOFs) materials, Ln(BTC)(H2O)·(DMF), were synthesized using the rare earth metal (Ln=Sm, Eu, Tb, Y) and 1,3,5-trimesic acid (BTC) as a metal ion center and ligand, respectively. X-ray diffraction (XRD) and infrared spectroscopy (FT-IR) were employed to characterize the Ln-MOFs structural features. The property of adsorption desul-furization of Ln-MOFs materials was evaluated with thiophene/n-octane as model oil. The results showed that Ln-MOFs with rare earth metals Sm, Eu, Tb and Y had perfect crystalline and good adsorption desulfurization ability. Y(BTC)(H2O)·(DMF) material had a comparatively better activity for the adsorption desulfurization with desulfurization rate up to 80.7%and the sulfur adsorption ca-pacity was found 30.7 mgS/g(Y-MOFs). The Ln-MOFs materials had excellent reusability.

  10. Sol-gel-derived hybrid materials multi-doped with rare-earth metal ions

    Science.gov (United States)

    Zelazowska, E.; Rysiakiewicz-Pasek, E.; Borczuch-Laczka, M.; Cholewa-Kowalska, K.

    2012-06-01

    Four different hybrid organic-inorganic materials based on TiO2-SiO2 matrices with organic additives and doped with rare-earth metal ions (III) from the group of europium, cerium, terbium, neodymium, dysprosium and samarium, were synthesized by sol-gel method. Tetraethyl orthosilicate, titanium (IV) isopropoxide and organic compounds, such as butyl acrylate, butyl methacrylate, ethyl acetoacetate, ethylene glycol dimethacrylate, ethyl acetate, propylene carbonate, organic solvents and certain inorganic salts were used in the synthesis. The inorganic part of the sols, which were used in the synthesis of all the hybrid materials, was prepared separately and then the organic parts were added. The materials obtained were aged for three weeks at room temperature and then heated in an electric oven for three hours at temperatures of 80 °C-150 °C. Scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM/EDX); X-ray diffraction (XRD); Fourier transform infrared spectroscopy (KBr technique); 29Si magic-angle spinning nuclear magnetic resonance; and fluorescence spectroscopy were used for the examination of morphology, microstructure and luminescence properties, respectively. Photoluminescence properties with relatively intense narrow emission lines of Tb, Eu, Dy, Nd, Sm respectively to the RE-ions doping, were observed for all the hybrid materials.

  11. Corrosion Inhibition Mechanism of Rare Earth Metal on LC4 Al Alloy with Spilt Cell Technique

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl3, the influence of corrosive performance of CeCl3 on LC4 super-power aluminum alloy in the 0.1 mol*L-1 NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl3 solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.

  12. In Vivo Uptake of Rare Earth Metals by Triple-Negative Breast Cancer Cells.

    Science.gov (United States)

    Roncati, Luca; Gatti, Antonietta Morena; Barbolini, Giuseppe; Piscioli, Francesco; Pusiol, Teresa; Maiorana, Antonio

    2017-02-09

    Rare earth metals (REM) are a group of 17 chemical elements in the periodic table, namely scandium (Sc), yttrium (Y) and the lanthanides. In relation to atomic volume and geological behavior, the lanthanides are further subdivided into light, medium and heavy REM. They find many applications in the technological field; however, their impact on the human health is still conflicting and, for many aspects, unknown. During a research program carried on 113 cases of female breast cancer, immunohistochemically categorized in Her2-positive (29 cases), Her2-negative (57 cases) and triple negative (27 cases), aimed to evaluate the role of environmental particulate in carcinogenesis by elemental microanalysis, for the first time in literature we have detected a REM uptake, in detail europium (Eu), dysprosium (Dy) and praseodymium (Pr), inside the neoplastic cells belonging to a single triple negative breast cancer. Curiously, the woman affected by this form of malignancy had worked in the ceramic industry, a well-known source of REM, during her life, and she was the one and only patient of our series to be dedicated to this activity. The medical repercussions of our findings are here discussed: in fact, a REM detection in only 1 of 113 examined cases seems to exclude active roles in breast carcinogenesis and discloses new possibilities for therapeutic developments in triple negative breast cancer.

  13. Homoleptic rare-earth metal(III) tetramethylaluminates: structural chemistry, reactivity, and performance in isoprene polymerization.

    Science.gov (United States)

    Zimmermann, Melanie; Frøystein, Nils Age; Fischbach, Andreas; Sirsch, Peter; Dietrich, H Martin; Törnroos, Karl W; Herdtweck, Eberhardt; Anwander, Reiner

    2007-01-01

    The complexes [Ln(AlMe4)3] (Ln=Y, La, Ce, Pr, Nd, Sm, Ho, Lu) have been synthesized by an amide elimination route and the structures of [Lu{(micro-Me)2AlMe2}3], [Sm{(micro-Me)2AlMe2}3], [Pr{(micro-Me)2AlMe2}3], and [La{(micro-Me)2AlMe2}2{(micro-Me)3AlMe}] determined by X-ray crystallography. These structures reveal a distinct Ln3+ cation size-dependency. A comprehensive insight into the intrinsic properties and solution coordination phenomena of [Ln(AlMe4)3] complexes has been gained from extended dynamic 1H and 13C NMR spectroscopic studies, as well as 1D 89Y, 2D 1H/89Y, and 27Al NMR spectroscopic investigations. [Ce(AlMe4)3] and [Pr(AlMe4)3] have been used as alkyl precursors for the synthesis of heterobimetallic alkylated rare-earth metal complexes. Both carboxylate and siloxide ligands can be introduced by methane elimination reactions that give the heterobimetallic complexes [Ln{(O2CAriPr)2(micro-AlMe2)}2(AlMe4)(C6H14)n] and [Ln{OSi(OtBu)3}(AlMe3)(AlMe4)2], respectively. [Pr{OSi(OtBu)3}(AlMe3)(AlMe4)2] has been characterized by X-ray structure analysis. All of the cerium and praseodymium complexes are used as precatalysts in the stereospecific polymerization of isoprene (1-3 equivalents of Et2AlCl as co-catalyst) and compared to the corresponding neodymium-based initiators reported previously. The superior catalytic performance of the homoleptic complexes leads to quantitative yields of high-cis-1,4-polyisoprene (>98%) in almost all of the polymerization experiments. In the case of the binary catalyst mixtures derived from carboxylate or siloxide precatalysts quantitative formation of polyisoprene is only observed for nLn:nCl=1:2. The influence of the metal size is illustrated for the heterobimetallic lanthanum, cerium, praseodymium, neodymium, and gadolinium carboxylate complexes, and the highest activities are observed for praseodymium as a metal center in the presence of one equivalent of Et2AlCl.

  14. The Evolving Chemistry Along Preferential Flow Paths in Alkaline Porous Media and its Significance for Heavy Metal Mobility

    Science.gov (United States)

    Bendz, D.; Flyhammar, P.; Ginn, T. R.

    2001-12-01

    It is common knowledge that physical and chemical heterogeneity are prominent features of geological formations and that they may have a large impact on the fate of contaminants. However, the particular influence of any underlying chemical heterogeneity is difficult to distinguish from experimental data because its manifestation depends on the hydraulic and physical properties of the system as well as the chemical components involved. Physical and chemical heterogeneity are also important features of man-made formations such as landfills. The chemical composition of the leachate that is discharged at the lower boundary of a landfill reflects the processes that take place in the landfill interior. However, anomalous behavior have been observed for both municipal solid waste landfills and municipal solid waste incineration bottom ash landfills: the chemical composition of the leachate indicates that the (bio-) geochemical conditions in the landfill interior alternate between different states depending on the leachate flux. The main hypothesis here is that this is an effect of chemical heterogeneity and a preferential flow field exhibiting a distribution of travel times ranging from hours to years. The importance of a non uniform flow field should not be underestimated when making predictions of expected leaching behavior on short and intermediate time scales, mainly because doing so may render predictions that are not conservative risk-wise. Model simulations demonstrate the influence of partial pressure of CO2, organic content, buffering capacity and matrix diffusion for the formation and movement of reaction (pH- and redox-) fronts and transport of heavy metals in an ensemble of preferential flow paths in a municipal solid waste incineration bottom ash landfill receiving acid rain.

  15. Electronic structure of alkali-metal/alkaline-earth-metal fluorine beryllium borate NaSr3Be3B3O9F4 single crystal: DFT approach

    Science.gov (United States)

    Reshak, A. H.; Kamarudin, H.; Auluck, S.

    2015-10-01

    The electronic band structure, total and angular momentum resolved projected density of states for NaSr3Be3B3O9F4 are calculated using the all-electron full potential linearized augmented plane wave plus local orbitals (FP-LAPW + lo) method. The calculations are performed within four exchange correlations namely; local density approximation (LDA), general gradient approximation (PBE-GGA), Engel-Vosko generalized gradient approximation (EVGGA) and the recently modified Becke-Johnson potential (mBJ). Calculations suggest that NaSr3Be3B3O9F4 is a direct wide band gap semiconductor. The exchange correlations potentials exhibit significant influence on the value of the energy gap being about 4.82 eV (LDA), 5.16 eV (GGA), 6.20 (EVGGA) and 7.20 eV (mBJ). The mBJ approach succeed by large amount in bringing the calculated energy gap closer to the experimental one (7.28 eV). The angular momentum resolved projected density of states shows the existence of a strong hybridization between the various orbitals. In additional we have calculated the electronic charge density distribution in two crystallographic planes namely (1 0 1) and (0 0 -1) to visualized the chemical bonding characters.

  16. Metal nitride cluster as a template to tune the electronic and magnetic properties of rare-earth metal containing endohedral fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yang

    2013-10-16

    Rare-earth metal containing endohedral fullerenes have attracted much attention due to the feasibility of encaging metal atom, atoms or cluster inside of carbon cages. By switching the metal atom or cluster entrapped inside of the carbon cage the physical and chemical properties of the fullerene compounds can be tuned. The understanding of magnetic and electrochemical properties of endohedral fullerenes plays an essential role in fundamental scientific researches and potential applications in materials science. In this thesis, synthesizing novel rare-earth metal containing endohedral fullerene structures, studying the properties of these isolated endohedral fullerenes and the strategies of tuning the electronic and magnetic properties of endohedral fullerenes were introduced. The DC-arc discharging synthesis of different lanthanide metal-based (Ho, Ce and Pr) mixed metal nitride clusterfullerenes was achieved. Those rare-earth metal containing endohedral fullerenes were isolated by multi-step HPLC. The isolated samples were characterized by spectroscopic techniques included UV-vis-NIR, FTIR, Raman, LDI-TOF mass spectrometry, NMR and electrochemistry. The Ho-based mixed metal nitride clusterfullerenes Ho{sub x}M{sub 3-x}N rate at C{sub 80} (M= Sc, Lu, Y; x=1, 2) were synthesized by ''reactive gas atmosphere'' method or ''selective organic solid'' route. The isolated samples were characterized by LDI-TOF mass spectrometry, UV-vis-NIR, FTIR, Raman and NMR spectroscopy. The {sup 13}C NMR spectroscopic studies demonstrated exceptional NMR behaviors that resulted from switching the second metal inside of the mixed metal nitride cluster Ho{sub x}M{sub 3-x}N from Sc to Lu and further to Y. The LnSc{sub 2}N rate at C{sub 80} (Ln= Ce, Pr, Nd, Tb, Dy, Ho, Lu) MMNCFs were characterized by {sup 13}C and {sup 45}Sc NMR study respectively. According to Bleaney's theory and Reilley method, the separation of δ{sup PC} and δ{sup con

  17. Stabilization effects of third element on CaCu5 type derivatives of rare-earth transition-metal intermetallics

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Part of the results of the key project "Search for novel rare-earth functional materials" supported by the National Natural Science Foundation of China is reviewed. In combination with reports in literature, the effects of the third element M on the formation and stability of La2(Co, M)17, R(Fe, M)12 and R3(Fe, M)29 intermetallic compounds are discussed by considering mixing enthalpy of M with rare-earth, Fe and Co, and atomic radius, electronegativity and electronic configurations, etc. It is concluded that the mixing en thalpy and atomic radius dominate the preferential sites and the minimum amount of M required to stabilize a structure, which ultimately affect the magnetic properties of a compound prominently. This review should provide some heuristic hints for exploiting novel rare-earth transition metal functional materials and for improving their performance.

  18. A Liquid Chromatography Detector for Transition and Rare-Earth Metal Ions Based on a Cupric Ion-Selective Electrode

    Science.gov (United States)

    1981-05-01

    selective Electrode A Transition Metal CuI) Rare Earth Potentiometry Lanthanide Flow-through Electrode 20. ABSTRACT (Continue on reverse side if necessary...Flow Potentiometry with Ion-selective Electrodes ..... . 19 i. Introduction - Ideal Ion-selective Electrodes . ... 19 2. Interferences...detector is less than I pL, creating much less peak broadening than the earlier polarographic detectors (9,10). C. Flow Potentiometry with Ion-Selective

  19. Optimization of film synthesized rare earth transition metal permanent magnet systems. Progress report, August 1, 1991--July 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Cadieu, F.J.

    1992-08-01

    Progress is reported in three areas: high coercivity Sm-Fe-Ti-V, Sm-Fe-Zr, and two element Sm-Fe Sm{sub 5}(Fe,T){sub 17} type crystalline phases; ThMn{sub 12} type pseudobinary SmFe{sub 12-x}T{sub x}(0{le}{times}{le}1.5); and sputter process control for the synthesis of precisely textured rare earth-transition metal magnetic films. (DLC)

  20. China Nonferrous Metal Invested 1.3-billion in a Rare Earth Separation Project in Xinfeng,Guangdong

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>On the 9th Oct,a signing ceremony on project investment and construction was held between China Nonferrous Metal Industry’s Foreign Engineering and Construction Co.,Ltd.and the Xinfeng County Government,Guangdong.According to agreement,the company will invest RMB 1.3 billion in Xinfeng County to develop a rare earth separation project in the south,in

  1. Palladium-rare-earth metal alloys-advanced materials for hydrogen power engineering

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Hydrogen of no less than 99. 999 % (vol. fraction) purity is a principal power media of hydrogen power engineering. A single method for the preparation of high purity hydrogen consists in its separation from vapour-gas mixtures via the selective diffusion of hydrogen through a palladium membrane. The rate of hydrogen diffusion and the strength and stability during the operation in aggressive gases are important characteristics of palladium membranes. The increase in the strength, plasticity, and hydrogen-permeability of membrane alloys can be reached by alloying palladium with the formation of solid solutions.The formation of wide ranges of palladium-rare-earth metal (REM) solid solutions is an interesting feature of palladium. Earlier, we have shown that the alloying of Pd with REM substantially increases the rate of hydrogen diffusion and markedly increases the strength of palladium on retention of the adequate plasticity.In this work, we have studied alloys of the Pd-Y and Pd-Y-Me systems. It was shown that the following conditions should be satisfied to prepare high-quality alloys exhibiting high service properties: (1)the use of high-purity components (whose purity is no less than 99.95%, mass fraction), in particular,high-purity Y prepared by vacuum distillation, and (2) holding the reached purity for the final product.For this purpose, we suggested a cycle of manufacturing operations including the preparation of a vacuumtight foil of 50 (m thick as the final stage.The hydrogen-permeability of the alloys was measured at different temperatures and hydrogen pressures. The instability of operation of binary Pd-Y alloys w alloying the composition with a Ⅷ Group metal. For example, the alloy of the optimum composition Pd-8Y-Me in the annealed state exhibits the following mechanical properties: HV= 75 kg/mm2 , σu = 58 kg/mm2 , and δ= 20%. Its hydrogen-permeability (QH2) measured as a function of the temperature exceeds that of the Pd-23Ag alloy (that is widely

  2. A mini-review on rare earth metal-doped TiO2 for photocatalytic remediation of wastewater.

    Science.gov (United States)

    Saqib, Najm Us; Adnan, Rohana; Shah, Irfan

    2016-08-01

    Titanium dioxide (TiO2) has been considered a useful material for the treatment of wastewater due to its non-toxic character, chemical stability and excellent electrical and optical properties which contribute in its wide range of applications, particularly in environmental remediation technology. However, the wide band gap of TiO2 photocatalyst (anatase phase, 3.20 eV) limits its photocatalytic activity to the ultraviolet region of light. Besides that, the electron-hole pair recombination has been found to reduce the efficiency of the photocatalyst. To overcome these problems, tailoring of TiO2 surface with rare earth metals to improve its surface, optical and photocatalytic properties has been investigated by many researchers. The surface modifications with rare earth metals proved to enhance the efficiency of TiO2 photocatalyts by way of reducing the band gap by shifting the working wavelength to the visible region and inhibiting the anatase-to-rutile phase transformations. This review paper summarises the attempts on modification of TiO2 using rare earth metals describing their effect on the photocatalytic activities of the modified TiO2 photocatalyst.

  3. Microstructure and composition of rare earth-transition metal-aluminium-magnesium alloys

    Directory of Open Access Journals (Sweden)

    Lia Maria Carlotti Zarpelon

    2008-03-01

    Full Text Available The determination of the microstructure and chemical composition of La0.7-xPr xMg0.3Al 0.3Mn0.4Co0.5 Ni3.8 (0 < x < 0.7 metal hydride alloys has been carried out using scanning electron microscopy (SEM, energy dispersive X ray analysis (EDX and X ray diffraction analysis (XRD. The substitution of La with Pr changed the grain structure from equiaxial to columnar. The relative atomic ratio of rare earth to (Al, Mn, Co, Ni in the matrix phase was 1:5 (LaNi5-type structure. Magnesium was detected only in two other phases present. A grey phase revealed 11 at.% Mg and the concentration ratios of other elements indicated the composition to be close to PrMgNi4. A dark phase was very heterogeneous in composition, attributed to the as-cast state of these alloys. The phases identified by XRD analysis in the La0.7Mg0.3Al0.3Mn0.4Co 0.5Ni3.8 alloy were: La(Ni,Co5, LaAl(Ni,Co4, La2(Ni,Co7 and AlMn(Ni,Co2. Praseodymium favors the formation of a phase with a PuNi3-type structure. Cobalt substituted Ni in the structures and yielded phases of the type: Pr(Ni,Co5 and Pr(Ni,Co3.

  4. Calculation of Interaction Parameters from Immiscible Phase Diagram of Alkali Metal or Alkali Earth Metal-Halide System by Means of Subregular Solution Model

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper, the interaction parameters in the subregular solution model, λ1 and λ2, are regarded as a linear function of temperature, T. Therefore, the molar excess Gibbs energy of A-B binary system may be reexpressed as follows: The calculation of the model parameters, λ11, λ12, λ21 and λ22, was carried out numerically from the phase diagrams for 11 alkali metal-alkali halide or alkali earth metal-halide systems.In addition, artificial neural network trained by known data has been used to predict the values of these model parameters. The predicted results are in good agreement with the.calculated ones. The applicability of the subregular solution model to the alkali metal-alkali halide or alkali earth metal-halide systems were tested by comparing the available experimental composition along the boundary of miscibility gap with the calculated ones which were obtained by using genetic algorithm. The good agreement between the calculated and experimental results across the entire liquidus is valid evidence in support of the model.

  5. [Development of metal ions analysis by ion chromatography].

    Science.gov (United States)

    Yu, Hong; Wang, Yuxin

    2007-05-01

    Analysis of metal ions by ion chromatography, including cation-exchange ion chromatography, anion-exchange ion chromatography and chelation ion chromatography, is reviewed. The cation-exchange ion chromatography is a main method for the determination of metal ions. Stationary phases in cation-exchange ion chromatography are strong acid cation exchanger (sulfonic) and weak acid cation exchanger (carboxylic). Alkali metal ions, alkaline earth metal ions, transition metal ions, rare earth metal ions, ammonium ions and amines can be analyzed by cation-exchange ion chromatography with a suitable detector. The anion-exchange ion chromatography is suitable for the separation and analysis of alkaline earth metal ions, transition metal ions and rare earth metal ions. The selectivity for analysis of metal ions with anion-exchange ion chromatography is good. Simultaneous determination of metal ions and inorganic anions can be achieved using anion-exchange ion chromatography. Chelation ion chromatography is suitable for the determination of trace metal ions in complex matrices. A total of 125 references are cited.

  6. Magnetocaloric effect in heavy rare-earth elements doped Fe-based bulk metallic glasses with tunable Curie temperature

    Science.gov (United States)

    Li, Jiawei; Huo, Juntao; Law, Jiayan; Chang, Chuntao; Du, Juan; Man, Qikui; Wang, Xinmin; Li, Run-Wei

    2014-08-01

    The effects of heavy rare earth (RE) additions on the Curie temperature (TC) and magnetocaloric effect of the Fe-RE-B-Nb (RE = Gd, Dy and Ho) bulk metallic glasses were studied. The type of dopping RE element and its concentration can easily tune TC in a large temperature range of 120 K without significantly decreasing the magnetic entropy change (ΔSM) and refrigerant capacity (RC) of the alloys. The observed values of ΔSM and RC of these alloys compare favorably with those of recently reported Fe-based metallic glasses with enhanced RC compared to Gd5Ge1.9Si2Fe0.1. The tunable TC and large glass-forming ability of these RE doped Fe-based bulk metallic glasses can be used in a wide temperature range with the final required shapes.

  7. On halide derivatives of rare-earth metal(III) oxidomolybdates(VI) and -tungstates(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Schleid, Thomas; Hartenbach, Ingo [Stuttgart Univ. (Germany). Inst. for Inorganic Chemistry

    2016-11-01

    Halide derivatives of rare-earth metal(III) oxidomolybdates(VI) have been investigated comprehensively over the last decade comprising the halogens fluorine, chlorine, and bromine. Iodide-containing compounds are so far unknown. The simple composition REXMoO{sub 4} (RE=rare-earth element, X=halogen) is realized for X=F almost throughout the complete lanthanide series as well as for yttrium. While ytterbium and lutetium do not form any fluoride derivative, for lanthanum, only a fluoride-deprived compound with the formula La{sub 3}FMo{sub 4}O{sub 16} is realized. Moreover, molybdenum-rich compounds with the formula REXMo{sub 2}O{sub 7} are also known for yttrium and the smaller lanthanoids. For X=Cl the composition REClMoO{sub 4} is known for yttrium and the whole lanthanide series, although, four different structure types were identified. Almost the same holds for X=Br, however, only two different structure types are realized in this class of compounds. In the case of halide derivatives of rare-earth metal(III) oxidotungstates(VI) the composition REXWO{sub 4} is found for chlorides and bromides only, so far. Due to the similar size of Mo{sup 6+} and W{sup 6+} cations, the structures found for the tungstates are basically the same as for the molybdates. With the larger lanthanides, the representatives for both chloride and bromide derivates exhibit similar structural motifs as seen in the molybdates, however, the crystal structure cannot be determined reliably. In case of the smaller lanthanoids, the chloride derivatives are isostructural with the respective molybdates, although the existence ranges differ slightly. The same is true for rare-earth metal(III) bromide oxidotungstates(VI).

  8. A rare earth alloy as a synthetic reagent: contrasting homo metallic rare earth and hetero bimetallic outcomes

    Energy Technology Data Exchange (ETDEWEB)

    Deacon, G.B.; Forsyth, C.M.; Junk, P.C.; Leary, S.G. [Monash Univ., School of Chemistry, Clayton (Australia)

    2006-04-15

    Reaction of LaNi{sub 5} with 2,2'-dipyridyl-amine (HNpy{sub 2}) at 170 C under vacuum gave crystals of dimeric [La(Npy{sub 2}){sub 3}]{sub 2} as a previously unknown eight-coordinate isomer (1a) (two {mu}-{eta}{sup 2}:{eta}{sup 2} and two terminal chelating (Namide,Npy) Npy{sub 2} ligands), which reverts to the known ten coordinate isomer (1b) on recrystallization from THF/PhMe, thereby establishing linkage isomerism of a [Ln(Npy{sub 2}){sub 3}]{sub 2} complex for the first time. Reaction of 8-hydroxyquinoline (HOQ) with excess LaNi{sub 5} alloy at 190 C resulted in extraction of both metals and the formation of hetero-bimetallic [Ni{sub 2}La(OQ){sub 7}] (2). The trinuclear complex has two terminal, fac-octahedral nickel(II) sites, each bound to three chelating 8-quinolinolate anions which bridge through the oxygen atoms to the lanthanum(III) centre. The eight-coordinate lanthanum environment is completed by a chelating OQ ligand. (authors)

  9. Lubricating oil compositions containing overbased calcium sulfonates and metal salts of alkyl catechol dithiophosphoric acid

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, E.S.; Cerrito, E.; Liston, T.V.

    1987-05-26

    This patent describes a lubricating oil composition containing an overbased calcium hydrocarbyl sulfonate. The improvement wherein the lubricating oil composition additionally comprises an effective amount to reduce wear of a metal salt of an alkyl catechol dithiophosphoric acid ester of the formula: wherein R is alkyl containing 10 to 18 carbon atoms, or mixtures thereof, M is an alkali or alkaline earth metal or transition metal and n corresponds to the valence of the metal M.

  10. Hydrothermal synthesis of mixed rare earth-alkali metal or ammonium fluorides

    Institute of Scientific and Technical Information of China (English)

    由芳田; 黄世华; 时秋峰

    2010-01-01

    The recent results on hydrothermal synthesis of mixed rare earth-alkali or ammonium fluorides were presented. The initial ratios of the starting materials, pH value and reaction temperature were the critical factors for obtaining the single-phase product. Four main types of complex rare earth fluorides, AREF4, A2REF5, ARE2F7 and ARE3F10 (A=Na+, K+, Rb+, NH4+), appeared in the primary hydrothermal reactions. The correlation between cation sizes and the formation of mixed rare earth fluorides under mild hydro...

  11. Lunar oxygen and metal for use in near-Earth space: Magma electrolysis

    Science.gov (United States)

    Colson, Russell O.; Haskin, Larry A.

    1990-01-01

    Because it is energetically easier to get material from the Moon to Earth orbit than from the Earth itself, the Moon is a potentially valuable source of materials for use in space. The unique conditions on the Moon, such as vacuum, absence of many reagents common on the Earth, and the presence of very nontraditional ores suggest that a unique and nontraditional process for extracting materials from the ores may prove the most practical. With this in mind, an investigation of unfluxed silicate electrolysis as a method for extracting oxygen, iron, and silicon from lunar regolith was initiated and is discussed. The advantages of the process include simplicity of concept, absence of need to supply reagents from Earth, and low power and mass requirements for the processing plant. Disadvantages include the need for uninterrupted high temperature and the highly corrosive nature of the high-temperature silicate melts which has made identifying suitable electrode and container materials difficult.

  12. High hydrogen loading of thin palladium wires through alkaline earth carbonates' precipitation on the cathodic surface - evidence of a new phase in the Pd-H system

    Energy Technology Data Exchange (ETDEWEB)

    Celani, F.; Spallone, A.; Di Gioacchino, D. [Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Frascati, Frascati, RM (Italy); Marini, P.; Di Stefano, V.; Nakamura, M. [EURESYS, Rome (Italy); Pace, S. [Salerno Univ., Salerno (Italy). Dept. of Physics, Istituto Nazionale per la Fisica della Materia; Mancini, A. [ORIM S.r.l., Piediripa, MC (Italy); Tripodi, P. [Stanford Research Institut International, Stanford, CA (United States)

    2000-07-01

    A new protocol for the electrolytic loading of hydrogen (H) in thin palladium (Pd) wires has been developed. In order to increase the cathodic overvoltage, which is known to be the main parameter capable to enhance the electrolytic H loading of Pd, the catalytic action of the Pd surface versus H-H recombination has been strongly reduced by precipitation of a thin layer of alkaline-earth carbonates on the cathode. A set of electrolytes has been employed, containing small amounts of hydrochloric or sulfuric acid and strontium or calcium ions. The H loading has been continuously evaluated through ac measurements of the Pd wire resistance. Uncommonly low resistivity values, leading to an estimate of exceptionally high H loading, have been observed. Evidence of the existence of a new phase in the very high H content region of the Pd-H system has been inferred on the basis of the determination of the temperature coefficient of the electrical resistivity. Mainly for this purpose a thin layer of Hg was galvanically deposed on the cathodic surface, in order to prevent any H deloading during the measurements. The results have been fully reproduced in other 2 well equipped and experienced Laboratories (Italy, USA).

  13. Effect of Rare Earths-Treated Glass Fiber on Impact Wear-Resistance of Metal-Plastic Multilayer Composites

    Institute of Scientific and Technical Information of China (English)

    程先华; 薛玉君; 谢超英

    2002-01-01

    The friction and wear properties under impact load and dry friction conditions of metal-plastic multilayer composites filled with glass fiber, treated with rare earth elements, were investigated. The worn surfaces were observed and analyzed by scanning electron microscopy (SEM). It shows that applying rare earth elements surface modifier to treat the glass fiber surface can enhance the interfacial adhesion between the glass fiber and polytetrafluoroethylene (PTFE), as well as promote the interface properties of the composites. This helps to form a uniformly distributed and high adhesive transfer film on the counterface and abate the friction between the composite and the counterface. As a result, the wear of composite is greatly reduced. The composite exhibits excellent friction properties and impact wear-resistance.

  14. Partial Oxidation of Butane to Syngas over Nickel SupportedCatalysts Modified by Alkali Metal Oxide and Rare-Earth Metal Oxide

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The partial oxidation of butane (POB) to syngas over nickel supported catalysts was first investigated with a flow-reactor, TG and UVRRS. The NiO/g-Al2O3 is the most suitable for the POB among NiO/g-Al2O3, NiO/MgO and NiO/SiO2. And the reaction performance of the NiO/g-Al2O3 shows little difference from those of the nickel supported catalysts modified by alkali metal oxide and rare-earth metal oxide. However, modification with Li2O and La2O3 can suppress carbon-deposition of the NiO/g-Al2O3, which contains graphite-like species during the POB reaction.

  15. Study of conformational and acid-base properties of norbadione A and pulvinic derivatives: Consequences on their complexation properties of alkaline and alkaline earth cations; Etude des proprietes conformationnelles et acido-basiques de la norbadione A et de derives pulviniques: consequences sur leurs proprietes complexantes de cations alcalins et alcalino-terreux

    Energy Technology Data Exchange (ETDEWEB)

    Kuad, P

    2006-01-15

    This work deals with the study of norbadione A, a pigment extracted from mushrooms and known to complex cesium cations. The study of the acid-base properties of norbadione A has allowed to determine the relative acidity of the seven protonable functions of the molecule and to reveal a reversible isomerization of the double exocyclic bond of the pulvinic moieties. The observed change of configuration is induced by a hydrogen bond of the H-O-H type and by electrostatic interactions. Moreover, the microscopic protonation mechanism of the norbadione A has been analyzed, considering three different study media where the acid-base properties of the norbadione A are compared. In the presence of 0.15 mol.l{sup -1} of NaCl, it has been observed a remarkable cooperativity in the protonation of the enol groups. At last, the use of different analytical methods (NMR, potentiometry and calorimetry) has allowed to study the complexing properties of the norbadione A towards cesium and other alkaline and rare earth cations. (O.M.)

  16. Rare Earth Doped GaN Laser Structures Using Metal Modulated Epitaxy

    Science.gov (United States)

    2015-03-30

    equivalent pressure ( BEP ). The Ga flux is expressed by the nitrogen equivalent pressure and pressure can also be translated to the same unit as growth rate...different metal sources by using their BEP and ionization energy etc. 29    Figure 2.5 Growth regions. With increasing substrate temperature, Ga...4 In equation 2.1, F is the metal flux; P is the BEP of the metal flux and IE is the ionization energy of each

  17. Density functional theory based screening of ternary alkali-transition metal borohydrides: A computational material design project

    DEFF Research Database (Denmark)

    Hummelshøj, Jens Strabo; Landis, David; Voss, Johannes

    2009-01-01

    We present a computational screening study of ternary metal borohydrides for reversible hydrogen storage based on density functional theory. We investigate the stability and decomposition of alloys containing 1 alkali metal atom, Li, Na, or K (M1); and 1 alkali, alkaline earth or 3d/4d transition...

  18. Syntheses and Structures of Alkali Metal Rare Earth Polyphosphates CsLn(PO3)4 (Ln = La, Ce)

    Institute of Scientific and Technical Information of China (English)

    ZHU Jing; CHENG Wen-Dan; ZHANG Hao; WU Dong-Sheng; ZHAO Dan

    2008-01-01

    Alkali metal-rare earth polyphosphates, CsLn(PO3)4 (Ln = La, Ce), were synthesized by the high temperature solution reaction and studied by single-crystal X-ray diffraction technique. They crystallize in the monoclinic space group P21 (Z = 2) and feature infinite PO4 spiral chains linked with neighboring CsO10 and LnO8 polyhedra. In addition, theoretically calculated energy band structure and density of states (DOS) by the density functional theory(DFT) predict that the solid-state compound CsLa(PO3)4 possesses insulative character.

  19. Cationic methyl complexes of the rare-earth metals: an experimental and computational study on synthesis, structure, and reactivity.

    Science.gov (United States)

    Kramer, Mathias U; Robert, Dominique; Arndt, Stefan; Zeimentz, Peter M; Spaniol, Thomas P; Yahia, Ahmed; Maron, Laurent; Eisenstein, Odile; Okuda, Jun

    2008-10-20

    Synthesis, structure, and reactivity of two families of rare-earth metal complexes containing discrete methyl cations [LnMe(2-x)(thf)n]((1+x)+) (x = 0, 1; thf = tetrahydrofuran) have been studied. As a synthetic equivalent for the elusive trimethyl complex [LnMe3], lithium methylates of the approximate composition [Li3LnMe6(thf)n] were prepared by treating rare-earth metal trichlorides [LnCl3(thf)n] with 6 equiv of methyllithium in diethyl ether. Heteronuclear complexes of the formula [Li3Ln2Me9L(n)] (Ln = Sc, Y, Tb; L = Et2O, thf) were isolated by crystallization from diethyl ether. Single crystal X-ray diffraction studies revealed a heterometallic aggregate of composition [Li3Ln2Me9(thf)n(Et2O)m] with a [LiLn2Me9](2-) core (Ln = Sc, Y, Tb). When tris(tetramethylaluminate) [Ln(AlMe4)3] (Ln = Y, Lu) was reacted with less than 1 equiv of [NR3H][BPh4], the dimethyl cations [LnMe2(thf)n][BPh4] were obtained. The coordination number as well as cis/trans isomer preference was studied by crystallographic and computational methods. Dicationic methyl complexes of the rare-earth metals of the formula [LnMe(thf)n][BAr4]2 (Ln = Sc, Y, La-Nd, Sm, Gd-Lu; Ar = Ph, C6H4F-4) were synthesized, by protonolysis of either the ate complex [Li3LnMe6(thf)n] (Ln = Sc, Y, Gd-Lu) or the tris(tetramethylaluminate) [Ln(AlMe4)3] (Ln = La-Nd, Sm, Dy, Gd) with ammonium borates [NR3H][BAr4] in thf. The number of coordinated thf ligands varied from n = 5 (Ln = Sc, Tm) to n = 6 (Ln = La, Y, Sm, Dy, Ho). The configuration of representative examples was determined by X-ray diffraction studies and confirmed by density-functional theory calculations. The highly polarized bonding between the methyl group and the rare-earth metal center results in the reactivity pattern dominated by the carbanionic character and the pronounced Lewis acidity: The dicationic methyl complex [YMe(thf)6](2+) inserted benzophenone as an electrophile to give the alkoxy complex [Y(OCMePh2)(thf)5](2+). Nucleophilic addition of

  20. Dimeric Complexes of Tryptophan with M2+ Metal Ions

    NARCIS (Netherlands)

    Dunbar, R. C.; Steill, J. D.; Polfer, N. C.; Oomens, J.

    2009-01-01

    IRMPD spectroscopy using the FELIX free electron laser and a Fourier transform ICR mass spectrometer was used to characterize the structures of electrosprayed dimer complexes M(2+)Trp(2) of tryptophan with a series of eight doubly charged metal ions, including alkaline earths Ca, Sr, and Ba, and tra

  1. Dihydrogen addition in a dinuclear rare-earth metal hydride complex supported by a metalated TREN ligand.

    Science.gov (United States)

    Venugopal, Ajay; Fegler, Waldemar; Spaniol, Thomas P; Maron, Laurent; Okuda, Jun

    2011-11-09

    The dinuclear lutetium dihydride dication supported by metalated tripodal ligands undergoes facile hydrogenolysis with H(2) to form a trihydride dication. Molecular orbital analysis shows that the LUMO is a bonding Lu···Lu orbital that is poised to activate dihydrogen.

  2. Siderophile elements in the upper mantle of the Earth: New clues from metal-silicate partition coefficients

    Science.gov (United States)

    Holzheid, A.; Borisov, A.; Palme, H.

    1993-01-01

    New, precise data on the solubilities of Ni, Co, and Mo in silicate melts at 1400 C and fO2 from IW to IW-2 are presented. The results suggest NiO, CoO as stable species in the melt. No evidence for metallic Ni or Co was found. Equilibrium was ensured by reversals with initially high Ni and Co in the glass. Mo appears to change oxidation state at IW-1, from MoO3 to MoO2. Metal-silicate partition coefficients calculated from these data and recent data on Pd indicate similar partition coefficients for Pd and Mo at the conditions of core formation. This unexpected result constrains models of core formation in the Earth.

  3. Thermodynamics of Modifying Effect of Rare Earth Oxide on Inclusions in Hardfacing Metal of Medium—High Carbon Steel

    Institute of Scientific and Technical Information of China (English)

    杨庆祥; 赵研辉; 等

    2002-01-01

    The modifying effect of rare earth(RE)oxide on inclusions in hardfacing metals of medium-high carbon steel was investigated by means of thermodynamics,The thermodynamic analsys for inclusion formation shows that RE oxide can be reduced to RE element by carbon,then the RE element can react with oxygen and sulfur to form the RE oxide,RE sulfide and RE oxide-sulfide in hardfacing molten pool.The deoxidization and the desulphurization can be carried otu and the liquid metal can be purified.In addition,RE oxide can also react with sulfur to form RE oxide-sulfide dirdctly.Therefore,the harmful effect of sulfur can be decreased.

  4. Model calculation of the static magnetic susceptibility in light rare earth metallic systems

    Science.gov (United States)

    Hammoud, Y.; Parlebas, J. C.

    1991-05-01

    Using the impurity Anderson model in the large N_f approximation, where N_f is the orbital and spin degeneracy of the f level, we calculate the zero temperature static paramagnetic susceptibility of light rare earth metallic systems. The calculation is performed for large values of the Coulomb U_ff electron-electron interactions with respect of the V hybridization of f1 and f2 configurations with the conduction states (i.e. f0 configuration) : we only keep the leading terms in a development in successive powers of 1/U_ff and V. Our numerical results on the magnetic susceptibility start from a simple analytic expression and are discussed in terms of the f level position, the hybridization V, the shape and filling of the conduction band and also the finite U_ff effects. Finally we present calculated curves for the susceptibility versus V in connection with the αγ transition of cerium and utilizing the same parameters as those used previously to obtain core level LIII absorption spectra : also in the case of the susceptibility, the hybridization appears to be an important parameter to describe the phase change from γ to α cerium. Nous utilisons le modèle d'Anderson à une impureté dans l'approximation des grands N_f où N_f est la dégénérescence d'orbitale et de spin du niveau f et nous calculons alors la susceptibilité paramagnétique statique (à température nulle) dans les systèmes métalliques de terres rares légères. Nous effectuons notre calcul pour des valeurs de l'interaction de Coulomb U_ff grandes par rapport à l'hybridation V des configurations f1 et f2 avec les états de conduction (c.-à-d. la configuration f0): nous ne retenons que les termes les plus imporatnts dans un développement en puissances successives de 1/U_ff et V. Ensuite nous discutons nos résultats numériques à partir d'une forme analytique simple obtenue pour la susceptibilité magnétique en fonction de la position du niveau f, de l'hybridation V, de la forme et du

  5. Rare-earth neutral metal injection into an electron beam ion trap plasma

    Energy Technology Data Exchange (ETDEWEB)

    Magee, E. W., E-mail: magee1@llnl.gov; Beiersdorfer, P.; Brown, G. V. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Hell, N. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Dr. Remeis-Sternwarte and ECAP, Universität Erlangen-Nürnberg, 96049 Bamberg (Germany)

    2014-11-15

    We have designed and implemented a neutral metal vapor injector on the SuperEBIT high-energy electron beam ion trap at the Lawrence Livermore National Laboratory. A horizontally directed vapor of a europium metal is created using a thermal evaporation technique. The metal vapor is then spatially collimated prior to injection into the trap. The source's form and quantity constraints are significantly reduced making plasmas out of metal with vapor pressures ≤10{sup −7} Torr at ≥1000 °C more obtainable. A long pulsed or constant feed metal vapor injection method adds new flexibility by varying the timing of injection and rate of material being introduced into the trap.

  6. Elemental partitioning and isotopic fractionation of Zn between metal and silicate and geochemical estimation of the S content of the Earth's core

    CERN Document Server

    Mahan, B; Pringle, E A; Moynier, F

    2016-01-01

    Zinc metal-silicate fractionation provides experimental access to the conditions of core formation and Zn has been used to estimate the S contents of the Earth's core and of the bulk Earth, assuming that they share similar volatility and that Zn was not partitioned into the Earth's core. We have conducted a suite of partitioning experiments to characterize Zn metal-silicate elemental and isotopic fractionation as a function of time, temperature, and composition. Experiments were conducted at temperatures from 1473-2273K, with run durations from 5-240 minutes for four starting materials. Chemical and isotopic equilibrium is achieved within 10 minutes. Zinc metal-silicate isotopic fractionation displays no resolvable dependence on temperature, composition, or oxygen fugacity. Thus, the Zn isotopic composition of silicate phases can be used as a proxy for bulk telluric bodies. Results from this study and literature data were used to parameterize Zn metal-silicate partitioning as a function of temperature, pressu...

  7. Rare Power China begins reinvigorate the rare earth industry after decades of underselling the valua metals

    Institute of Scientific and Technical Information of China (English)

    HU YUE

    2011-01-01

    On May 19,the State Council released Guidelines to Promote Sustainable and Sound Development of the Rare Earth Industry,delivering a strong boost to the fragmented industry.Rare earth elements,a collection of 17 elements,are among the most soughtafter materials for modern manufacturing.Their unique magnetic and phosphorescent properties make them vital ingredients in sophisticated hi-tech devices like batteries,magnets,wind turbines,cellphones,electric cars and flat-screen televisions.However,mining and smelting the elements are difficult and costly.

  8. Review of magnetic properties and magnetocaloric effect in the intermetallic compounds of rare earth with low boiling point metals

    Science.gov (United States)

    Ling-Wei, Li

    2016-03-01

    The magnetocaloric effect (MCE) in many rare earth (RE) based intermetallic compounds has been extensively investigated during the last two decades, not only due to their potential applications for magnetic refrigeration but also for better understanding of the fundamental problems of the materials. This paper reviews our recent progress on studying the magnetic properties and MCE in some binary or ternary intermetallic compounds of RE with low boiling point metal(s) (Zn, Mg, and Cd). Some of them exhibit promising MCE properties, which make them attractive for low temperature magnetic refrigeration. Characteristics of the magnetic transition, origin of large MCE, as well as the potential application of these compounds are thoroughly discussed. Additionally, a brief review of the magnetic and magnetocaloric properties in the quaternary rare earth nickel boroncarbides RENi2B2C superconductors is also presented. Project supported by the National Natural Science Foundation of China (Grant Nos. 11374081 and 11004044), the Fundamental Research Funds for the Central Universities, China (Grant Nos. N150905001, L1509006, and N140901001), the Japan Society for the Promotion of Science Postdoctoral Fellowships for Foreign Researchers (Grant No. P10060), and the Alexander von Humboldt (AvH) Foundation (Research stipend to L. Li).

  9. Rare earth metals appliance for magnetic admixtures recovery from mineral premixes

    Directory of Open Access Journals (Sweden)

    A. A. Shevtsov

    2012-01-01

    Full Text Available The analysis of the material composition metallomagnetic admixtures of mineral premix. It is shown that the dressed metallomagnetic impurity includes low-magnetic particles with low magnetic susceptibility. Removing these particles from the product stream in process of magnetic separation using high-energy rare earth magnets is a challenging task.

  10. Impurities especially titanium in the rare earth metal gadolinium-before and after solid state electrotransport

    Institute of Scientific and Technical Information of China (English)

    苗睿瑛; 张小伟; 朱琼; 张志琦; 王志强; 颜世宏; 陈德宏; 周林; 李宗安

    2014-01-01

    Gadolinium was prepared by conventional procedures of fluorination, reduction, distillation and solid state electrotransport (SSE). The electronegativities of the metals were found to have an important influence on the electrotransport process and result of the impurity element. Meanwhile, titanium particles in the distilled gadolinium as major metallic impurities were studied by high resolution transmission electron microscopy (HRTEM) before and after solid state electrotransport. The results showed that impurities especially titanium transported from anode to cathode during SSE. In the metal before SSE, there were impurities of titanium in strip shape or embedded round shape. After SSE processing, titanium particles in the metal smaller than 50 nm in the cathode, but existed 6 to 10 times bigger in the anode.

  11. Prebiotic Synthesis of Glycine from Ethanolamine in Simulated Archean Alkaline Hydrothermal Vents

    Science.gov (United States)

    Zhang, Xianlong; Tian, Ge; Gao, Jing; Han, Mei; Su, Rui; Wang, Yanxiang; Feng, Shouhua

    2016-09-01

    Submarine hydrothermal vents are generally considered as the likely habitats for the origin and evolution of early life on Earth. In recent years, a novel hydrothermal system in Archean subseafloor has been proposed. In this model, highly alkaline and high temperature hydrothermal fluids were generated in basalt-hosted hydrothermal vents, where H2 and CO2 could be abundantly provided. These extreme conditions could have played an irreplaceable role in the early evolution of life. Nevertheless, sufficient information has not yet been obtained for the abiotic synthesis of amino acids, which are indispensable components of life, at high temperature and alkaline condition. This study aims to propose a new method for the synthesis of glycine in simulated Archean submarine alkaline vent systems. We investigated the formation of glycine from ethanolamine under conditions of high temperature (80-160 °C) and highly alkaline solutions (pH = 9.70). Experiments were performed in an anaerobic environment under mild pressure (0.1-8.0 MPa) at the same time. The results suggested that the formation of glycine from ethanolamine occurred rapidly and efficiently in the presence of metal powders, and was favored by high temperatures and high pressures. The experiment provides a new pathway for prebiotic glycine formation and points out the phenomenal influence of high-temperature alkaline hydrothermal vents in origin of life in the early ocean.

  12. The influence of different alkaline earth oxides on the structural and optical properties of undoped, Ce-doped, Sm-doped, and Sm/Ce co-doped lithium alumino-phosphate glasses

    Science.gov (United States)

    Othman, H. A.; Arzumanyan, G. M.; Möncke, D.

    2016-12-01

    Undoped, singly Sm doped, Ce doped, and Sm/Ce co-doped lithium alumino-phosphate glasses with different alkaline earth modifiers were prepared by melt quenching. The structure of the prepared glasses was investigated by FT-IR and Raman, as well as by optical spectroscopy. The effect of the optical basicity of the host glass matrix on the added active dopants was studied, as was the effect doping had on the phosphate structural units. The optical edge shifts toward higher wavelengths with an increase in the optical basicity due to the increased polarizability of the glass matrix, but also with increasing CeO2 concentration as a result of Ce3+/Ce4+ inter valence charge transfer (IV-CT) absorption. The optical band gap for direct and indirect allowed transitions was calculated for the undoped glasses. The glass sample containing Mg2+ modifier ions is found to have the highest value (4.16 eV) for the optical band gap while Ba2+ has the lowest value (3.61 eV). The change in the optical band gap arises from the structural changes and the overall polarizability (optical basicity). Refractive index, molar refractivity Rm and molar polarizability αm values increase with increasing optical basicity of the glasses. The characteristic absorption peaks of Sm3+ were also investigated. For Sm/Ce co-doped glasses, especially at high concentration of CeO2, the absorption of Ce3+ hinders the high energy absorption of Sm3+ and this effect becomes more obvious with increasing optical basicity.

  13. Melting and metallization of silica in the cores of gas giants, ice giants and super Earths

    CERN Document Server

    Mazevet, S; Taniuchi, T; Benuzzi-Mounaix, A; Guyot, F

    2014-01-01

    The physical state and properties of silicates at conditions encountered in the cores of gas giants, ice giants and of Earth like exoplanets now discovered with masses up to several times the mass of the Earth remains mostly unknown. Here, we report on theoretical predictions of the properties of silica, SiO$_2$, up to 4 TPa and about 20,000K using first principle molecular dynamics simulations based on density functional theory. For conditions found in the Super-Earths and in ice giants, we show that silica remains a poor electrical conductor up to 10 Mbar due to an increase in the Si-O coordination with pressure. For Jupiter and Saturn cores, we find that MgSiO$_3$ silicate has not only dissociated into MgO and SiO$_2$, as shown in previous studies, but that these two phases have likely differentiated to lead to a core made of liquid SiO$_2$ and solid (Mg,Fe)O.

  14. Magnetocaloric effect in heavy rare-earth elements doped Fe-based bulk metallic glasses with tunable Curie temperature

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jiawei; Huo, Juntao; Chang, Chuntao, E-mail: ctchang@nimte.ac.cn, E-mail: dujun@nimte.ac.cn; Du, Juan, E-mail: ctchang@nimte.ac.cn, E-mail: dujun@nimte.ac.cn; Man, Qikui; Wang, Xinmin; Li, Run-Wei [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, Zhejiang 315201 (China); Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, Zhejiang 315201 (China); Law, Jiayan [Department of Applied Physics, Chalmers University of Technology, SE-412 96 Göteborg (Sweden)

    2014-08-14

    The effects of heavy rare earth (RE) additions on the Curie temperature (T{sub C}) and magnetocaloric effect of the Fe-RE-B-Nb (RE = Gd, Dy and Ho) bulk metallic glasses were studied. The type of dopping RE element and its concentration can easily tune T{sub C} in a large temperature range of 120 K without significantly decreasing the magnetic entropy change (ΔS{sub M}) and refrigerant capacity (RC) of the alloys. The observed values of ΔS{sub M} and RC of these alloys compare favorably with those of recently reported Fe-based metallic glasses with enhanced RC compared to Gd{sub 5}Ge{sub 1.9}Si{sub 2}Fe{sub 0.1}. The tunable T{sub C} and large glass-forming ability of these RE doped Fe-based bulk metallic glasses can be used in a wide temperature range with the final required shapes.

  15. Surface shift of the occupied and unoccupied 4f levels of the rare-earth metals

    DEFF Research Database (Denmark)

    Aldén, Magnus; Johansson, Börje; Skriver, Hans Lomholt

    1995-01-01

    The surface energy shifts of the occupied and unoccupied 4f levels for the lanthanide metals have been calculated from first principles by means of a Green’s-function technique within the tight-binding linear muffin-tin orbitals method. We use the concept of complete screening to identify...... as well as those found in previous initial-state model calculations. The present theory agrees well with very recent high-resolution, single-crystal film measurements for Gd, Tb, Dy, Ho, Er, Tm, and Lu. We furthermore utilize the unique possibility offered by the lanthanide metals to clarify the roles...

  16. High-Tc Superconductivity and Raman Scattering Study of the phonon properties of electron doped (transition metal, rare-earth) - Oxygen-Free CaFeAsF and compared with RFeAsO system

    Science.gov (United States)

    Sasmal, Kalyan; Hadjiev, Viktor; Chu, C. W.(Paul)

    Quaternary CaFeAsF has ZrCuSiAs-type structure,(RO)δ+ layer in RFeAsO replaced by (CaF)δ+ layer,with tetragonal (P4/nmm)-orthorhombic (Cmma) phase transition at 134K,while magnetic order,SDW sets in at 114K. Partial replacement of Fe with Co/Ni is direct electron doping to (FeAs)δ+ layer.Tc ~15K in CaFe0.9Ni0.1AsF.Substitution of rare earth metal for alkaline earth metal suppresses anomaly in resistivity & induces superconductivity.Tc ~52K in Ca0.5Pr0.5FeAsF.Characterized by resistivity, susceptibility,XRD & EDX-SEM.Upper critical field estimated from magneto resistance.Bulk superconductivity proved by DC magnetization. Hall coefficient RH revealed hole-like charge carriers in parent compound CaFeAsF, while electron-type (RH in normal state is -Ve) for Ca0.5Pr0.5FeAsF.Evolution of Raman active phonons of Ca1-xPrxFeAsF measured with polarized Raman spectroscopy at room temperature from absurfaces of impurity-free microcrystals.Spectra exhibit sharp phonon lines on very weak electronic scattering background.Frequency and symmetry of Raman phonons involving out-of-plane atomic vibrations are found at 162.5 cm-1 (A1 g, Pr), 201 cm-1 (A1 g, As), 215.5 cm-1 (B1 g, Fe), 265 cm-1 (Eg, Fe) and 334 cm-1 (B1 g, F) for Ca0.5Pr0.5FeAsF.Observations are compared with RFeAsO unconventional superconductors also possibly related to magnetic fluctuations

  17. Alkaline earth stannates: The next silicon?

    Energy Technology Data Exchange (ETDEWEB)

    Ismail-Beigi, Sohrab, E-mail: sohrab.ismail-beigi@yale.edu; Ahn, Charles H. [Department of Applied Physics, Yale University, New Haven, Connecticut 06520 (United States); Department of Physics, Yale University, New Haven, Connecticut 06520 (United States); Department of Mechanical Engineering and Materials Science, Yale University, New Haven, Connecticut 06520 (United States); Center for Research on Interface Structure and Phenomena, Yale University, New Haven, Connecticut 06520 (United States); Walker, Frederick J. [Department of Applied Physics, Yale University, New Haven, Connecticut 06520 (United States); Center for Research on Interface Structure and Phenomena, Yale University, New Haven, Connecticut 06520 (United States); Cheong, Sang-Wook [Department of Physics and Astronomy, Rutgers University, Piscataway, New Jersey 08854 (United States); Rutgers Center for Emergent Materials, Rutgers University, Piscataway, New Jersey 08854 (United States); Rabe, Karin M. [Department of Physics and Astronomy, Rutgers University, Piscataway, New Jersey 08854 (United States)

    2015-06-01

    Semiconductor materials are being used in an increasingly diverse array of applications, with new device concepts being proposed each year for solar cells, flat-panel displays, sensors, memory, and spin transport. This rapid progress of invention outpaces the development of new semiconductor materials with the required properties and performance. In many applications, high carrier mobility at room temperature is required in addition to specific functional properties critical to the device concept. We review recent developments on high mobility stannate perovskite oxide materials and devices.

  18. Alkaline earth stannates: The next silicon?

    Directory of Open Access Journals (Sweden)

    Sohrab Ismail-Beigi

    2015-06-01

    Full Text Available Semiconductor materials are being used in an increasingly diverse array of applications, with new device concepts being proposed each year for solar cells, flat-panel displays, sensors, memory, and spin transport. This rapid progress of invention outpaces the development of new semiconductor materials with the required properties and performance. In many applications, high carrier mobility at room temperature is required in addition to specific functional properties critical to the device concept. We review recent developments on high mobility stannate perovskite oxide materials and devices.

  19. PARAMAGNETIC PROPERTIES OF THE ALKALINE EARTH FLUORIDES.

    Science.gov (United States)

    decreases with increasing temperature; and the temperature dependance is stronger for SrF2. The results have been interpreted using the Simanek-Orbach theory of a phonon-induced hyperfine field. (Author)

  20. Positron elastic scattering from alkaline earth targets

    Science.gov (United States)

    Poveda, Luis A.; Assafrão, Denise; Mohallem, José R.

    2016-07-01

    A previously reported model potential approach [Poveda et al., Phys. Rev. A 87, 052702 (2013)] was extended to study low energy positron elastic scattering from beryllium and magnesium. The cross sections were computed for energies ranging from 10-5 eV up to well above the positronium formation threshold. The present results are in good agreement with previous reports, including the prediction of a p-wave resonance in the cross section for magnesium. The emergence of this shape resonance is connected to a trend observed in the evolution of the partial wave cross section in going from Be to Mg target. This trend lead us to speculate that a sharp d-wave resonance should be observed in positron elastic scattering from calcium. The positron-target binding energies are investigated in detail, both using the scattering information and by direct computation of the bound state energies using the model potentials. Contribution to the Topical Issue "Advances in Positron and Electron Scattering", edited by Paulo Limao-Vieira, Gustavo Garcia, E. Krishnakumar, James Sullivan, Hajime Tanuma and Zoran Petrovic.Supplementary material in the form of one pdf file available from the Journal web page at http://dx.doi.org/10.1140/epjd/e2016-70120-y

  1. Electrical properties of alkaline earth fluorohalide crystals

    Energy Technology Data Exchange (ETDEWEB)

    Ayachour, D. (Lab. PHASE, C.R.N., 67 - Strasbourg (France)); Sieskind, M. (Groupe d' Optique, Non-Lineaire, 67 - Strasbourg (France)); Geist, P. (C.R.N.-G.O.P.A., 67 - Strasbourg (France))

    1991-07-01

    The ionic conductivity of undoped BaFCl, BaFBr, BaFI, SrFCl, and SrFBr single crystals is measured. The activation energies for a variety of anion vacancy mechanisms and the Schottky energy are defined. They are found to be in good agreement with Baetzold's theoretical data. Partial measurements of the static dielectric constant point out that these materials show an important dipolar contribution which is connected with their antiferroelectric character. (orig.).

  2. Precious metals and rare earth elements in municipal solid waste – Sources and fate in a Swiss incineration plant

    Energy Technology Data Exchange (ETDEWEB)

    Morf, Leo S., E-mail: leo.morf@bd.zh.ch [Baudirektion Kanton Zürich, Amt für Abfall, Wasser, Energie und Luft, Zurich (Switzerland); Gloor, Rolf; Haag, Olaf [Bachema AG, Schlieren (Switzerland); Haupt, Melanie [Zentrum für nachhaltige Abfall-und Ressourcennutzung ZAR, Hinwil (Switzerland); Skutan, Stefan [Bachema AG, Schlieren (Switzerland); Lorenzo, Fabian Di; Böni, Daniel [Zentrum für nachhaltige Abfall-und Ressourcennutzung ZAR, Hinwil (Switzerland)

    2013-03-15

    Highlights: ► We carefully addressed all the very valuable comments and suggestions of the reviewers. ► We also have shortened the size of the paper and tried simplify it substantially, as requested by the reviewers (introduction 25% reduced!). ► We have decided to take the chance and have replaced the data for the “additional” elements (Cu, Cd, Zn, Pb, Sn, Cr, Ni, Fe, Al) of the earlier MFA (Morf, 2011) with data that belong to the samples of this study. ► We are convinced that with the revision the paper has significantly improved in quality and attractiveness. - Abstract: In Switzerland many kinds of waste, e.g. paper, metals, electrical and electronic equipment are separately collected and recycled to a large extent. The residual amount of municipal solid waste (MSW) has to be thermally treated before final disposal. Efforts to recover valuable metals from incineration residues have recently increased. However, the resource potential of critical elements in the waste input (sources) and their partitioning into recyclable fractions and residues (fate) is unknown. Therefore, a substance flow analysis (SFA) for 31 elements including precious metals (Au, Ag), platinum metal group elements (Pt, Rh) and rare earth elements (La, Ce, etc.) has been conducted in a solid waste incinerator (SWI) with a state-of-the-art bottom ash treatment according to the Thermo-Re® concept. The SFA allowed the determination of the element partitioning in the SWI, as well as the elemental composition of the MSW by indirect analysis. The results show that the waste-input contains substantial quantities of precious metals, such as 0.4 ± 0.2 mg/kg Au and 5.3 ± 0.7 mg/kg Ag. Many of the valuable substances, such as Au and Ag are enriched in specific outputs (e.g. non-ferrous metal fractions) and are therefore recoverable. As the precious metal content in MSW is expected to rise due to its increasing application in complex consumer products, the results of this study are

  3. Elemental partitioning and isotopic fractionation of Zn between metal and silicate and geochemical estimation of the S content of the Earth's core

    Science.gov (United States)

    Mahan, Brandon; Siebert, Julien; Pringle, Emily A.; Moynier, Frédéric

    2017-01-01

    Zinc metal-silicate fractionation provides experimental access to the conditions of core formation and Zn has been used to estimate the S contents of the Earth's core and of the bulk Earth, assuming that they share similar volatility and that Zn was not partitioned into the Earth's core. Therefore, Zn provides both direct and indirect information into the origin and eventual fate of volatile and siderophile elements on Earth. However, the partitioning of Zn between metal and silicate - as well as the associated isotopic fractionation - is not well known. We have conducted a suite of partitioning experiments to characterize Zn elemental partitioning and isotopic fractionation between metal and silicate as a function of time, temperature, and composition. Experiments were conducted at 2 GPa and temperatures from 1473 K to 2273 K in a piston cylinder apparatus, with run durations from 5 to 240 min for four distinct starting materials. Chemical and isotopic equilibrium is achieved within 10 min of experimental outset. Zinc metal-silicate isotopic fractionation displays no resolvable dependence on temperature, composition, or oxygen fugacity within the data set. Therefore, the Zn isotopic composition of silicate phases can be used as a proxy for bulk telluric bodies. Partitioning results from this study and data from literature were used to robustly parameterize Zn metal-silicate partitioning as a function of temperature, pressure, and redox state. Using this parametric characterization and viable formation conditions, we have estimated a range of Zn contents in the cores of iron meteorite parent bodies (i.e. iron meteorites) of ∼0.1-150 ppm, in good agreement with natural observations. We have also calculated the first geochemical estimates for the Zn contents of the Earth's core and of the bulk Earth, at 242 ± 107 ppm and 114 ± 34 ppm (respectively), that consider the slightly siderophile behavior of Zn. These estimates of the Zn contents of the Earth's core and

  4. Metallic complexes with glyphosate: a review; Complexos metalicos com o herbicida glifosato: revisao

    Energy Technology Data Exchange (ETDEWEB)

    Coutinho, Claudia F.B.; Mazo, Luiz Henrique [Sao Paulo Univ., Sao Carlos, SP (Brazil). Inst. de Quimica]. E-mail: claudiabreda@iqsc.usp.br

    2005-11-15

    We present studies involving metallic ions and the herbicide glyphosate. The metallic complexes of Cu(II), Zn(II), Mn(II), Ni(II), Cd(II), Pb(II), Cr(III), Fe(III), Co(III), ammonium, sodium, Ag(I), alkaline earth metals and of some lanthanides ions are described. The complexes are discussed in terms of their synthesis, identification, stability and structural properties, based on data from the current literature. (author)

  5. Antimony film sensor for sensitive rare earth metal analysis in environmental samples.

    Science.gov (United States)

    Makombe, Martin; van der Horst, Charlton; Silwana, Bongiwe; Iwuoha, Emmanuel; Somerset, Vernon

    2016-07-02

    A sensor for the adsorptive stripping voltammetric determination of rare earth elements has been developed. The electrochemical procedure is based on the oxidation of the rare earth elements complexed with alizarin complexone at a glassy carbon electrode that was in situ modified with an antimony film, during an anodic scan from -0.2 V to 1.1 V (vs. Ag/AgCl) and deposition potential of -0.1 V (vs. Ag/AgCl). The factors influencing the adsorptive stripping capability were optimised, including the complexing agent concentration, plating concentration of antimony and deposition time. The detection of rare earth elements (La, Ce and Pr) were realised in 0.08 M sodium acetate (pH = 5.8) solution as supporting electrolyte, with 2 × 10(-6) M alizarin complexone and 1.0 mg L(-1) antimony solution. Under the optimised conditions, a deposition time of 360 s was obtained and a linear response was observed between 1 and 25 µg L(-1). The reproducibility of the voltammetric measurements was found to be within 5.0% RSD for 12 replicate measurements of cerium(III) concentration of 5 µg L(-1) using the same electrode surface. The detection limits obtained using stripping analysis was 0.06, 0.42 and 0.71 μg L(-1) for Ce(III), La(III) and Pr(III), respectively. The developed sensor has been successfully applied for the determination of cerium, lanthanum and praseodymium in municipal tap water samples.

  6. Applying ellipsometry to studying the effect of two kinds of rare earth metal salts on anodizing aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    H00G Quan; QIAN Ying; LI Lingjie; ZHANG Shengtao

    2004-01-01

    The effects of rare earth metal salts (REMs), cerium(Ⅳ) salt and lanthanum (Ⅲ) salt, on the property of anodized coating of LD10 aluminum alloy are studied by corrosion tests including neutral salt spray test and copper accelerated acetic acid immersion test, polarization curves measurement, energy dispersion analyzer of X-Ray(EDAX) analysis, and in situ ellipsometry. The results show that the addition of either of the two REMs in anodizing solution hardly changes the composition of an anodized coating, while increases the thickness of barrier part and reduces the porosity of porous part, which contributed to the improvement of the corrosion resistance of the anodized coating. The results also demonstrate that the effect of cerium salt was better than that of lanthanum salt.

  7. Low-temperature activation of methane over rare earth metals promoted Zn/HZSM-5 zeolite catalysts in the presence of ethylene

    Institute of Scientific and Technical Information of China (English)

    Hengqiang Zhang; Aiguo Kong; Yongjie Ding; Chengyong Dai; Yongkui Shan

    2011-01-01

    At low temperature of 723 K, methane can be easily activated in the presence of ethylene in the feed, and converted to higher hydrocarbons (C2-C4) and aromatics (C6-C10), through its reaction over rare metals modified Zn/HZSM-5 zeolite catalysts without undesirable carbon oxides formation.Methane can get 37.3% conversion over the above catalysts under Iow temperature, and the catalysts show a longer lifetime than usual metal supported HZSM-5 zeolite catalysts without adding any rare earth metals.The effects of methane activation over various rare earth metal promoted Zn/HZSM-5 catalysts on the products and influences of several reaction conditions such as temperature, catalyst lifetime and molar ratio of CH4/C2H4 have been discussed.

  8. Rare earth metals influence on morphology of non-metallic inclusions and mechanism of GP240GH and G17CrMo5-5cast steel cracking

    Directory of Open Access Journals (Sweden)

    M. Gajewski

    2009-10-01

    Full Text Available This paper presents results of research carried out in order to specify the influence of the rare earth metals on the morphology of the occuring non-metallic inclusions as well as on the cracking mechanism of GP240GH cast carbon steel and G17CrMo5-5 (0.18%C, 1.2%Cr, 0.53%Mo high temperature cast steel. The tests have been performed on successive industrial melts adding rare earth metals to the ladle during tapping of heat melt from the furnace. It was found that ball-shaped non-metalic inclusions occuring as a result of the rare earth metals influence are heterogenic and they significantly influence the cracking mechanism of Charpy specimens and the impact strength. The morphology of the specimens fracture surface has been substantially changed as a result of the rare earth metals modification. The impact strength of the tested cast carbon steel increased from 100 J/cm2 to ca 155 J/cm2, and the high-temperature cast steel from 30 J/cm2 to ca 100 J/cm2.

  9. Core and shallow-core d- to f-shell excitations in rare-earth metals

    Science.gov (United States)

    Bradley, J. A.; Moore, K. T.; van der Laan, G.; Bradley, J. P.; Gordon, R. A.

    2011-11-01

    We report on the results of probing the light lanthanide metals Ce, Pr, and Nd with inelastic x-ray and electron scattering. Aberration-corrected transmission electron microscope-based electron spectroscopy and nonresonant inelastic x-ray scattering are shown to be in a high degree of accord and here serve as complementary probes of electronic structure. The high resolution and high signal-to-noise electron technique allows for the measurement of the complex and subtle excitation spectra in the lanthanide metals, validating the applicability of the screened trivalent atomic model used for these materials. In addition, the momentum transfer dependence of the x-ray scattering is extracted and compared against atomic calculations for the most tightly bound excitonic resonances, which provides a direct test of the predicted atomic radial wave functions.

  10. Chemical composition of modern and fossil Hippopotamid teeth and implications for paleoenvironmental reconstructions and enamel formation – Part 2: Alkaline earth elements as tracers of watershed hydrochemistry and provenance

    Directory of Open Access Journals (Sweden)

    I. Ssemmanda

    2012-03-01

    Full Text Available For reconstructing environmental change in terrestrial realms the geochemistry of fossil bioapatite in bones and teeth is among the most promising applications. This study demonstrates that alkaline earth elements in enamel of Hippopotamids, in particular Ba and Sr are tracers for water provenance and hydrochemistry. The studied specimens are molar teeth from Hippopotamids found in modern and fossil lacustrine settings of the Western Branch of the East African Rift system (Lake Kikorongo, Lake Albert, and Lake Malawi and from modern fluvial environments of the Nile River. Concentrations in enamel vary by ca. two orders of magnitude for Ba (120–9336 μg g−1 as well as for Sr (9–2150 μg g−1. Concentration variations in enamel are partly induced during post-mortem alteration and during amelogenesis, but the major contribution originates from the variable water chemistry in the habitats of the Hippopotamids which is dominated by the lithologies and weathering processes in the watershed areas. Amelogenesis causes a distinct distribution of Ba and Sr in modern and fossil enamel, in that element concentrations increase along profiles from the outer rim towards the enamel-dentin junction by a factor of 1.3–1.5. These elements are well correlated with MgO and Na2O in single specimens, thus suggesting that their distribution is determined by a common, single process. Presuming that the shape of the tooth is established at the end of the secretion process and apatite composition is in equilibrium with the enamel fluid, the maturation process can be modeled by closed system Rayleigh crystallization. Enamel from many Hippopotamid specimens has Sr/Ca and Ba/Ca which are typical for herbivores, but the compositions extend well into the levels of plants and carnivores. Within enamel from single specimens these element ratios covary and provide a specific fingerprint of the Hippopotamid habitat. All specimens together, however, define subparallel

  11. Synchrotron Diffraction Studies of Spontaneous Magnetostriction in Rare Earth Transition Metal Compounds

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ning [Iowa State Univ., Ames, IA (United States)

    2004-12-19

    Thermal expansion anomalies of R2Fe14B and R2Fe17Cx (x = 0,2) (R = Y, Nd, Gd, Tb, Er) stoichiometric compounds are studied with high-energy synchrotron X-ray powder diffraction using Debye-Schemer geometry in temperature range 10K to 1000K. Large spontaneous magnetostriction up to their Curie temperatures (Tc) is observed. The a-axes show relatively larger invar effects than c-axes in the R2Fe14B compounds whereas the R2Fe17Cx show the contrary anisotropies. The iron sub-lattice is shown to dominate the spontaneous magnetostriction of the compounds. The contribution of the rare earth sublattice is roughly proportional to the spin magnetic moment of the rare earth in the R2Fe14B compounds but in R2Fe17Cx, the rare earth sub-lattice contribution appears more likely to be dominated by the local bonding. The calculation of spontaneous magnetostrain of bonds shows that the bonds associated with Fe(j2) sites in R2Fe14B and the dumbbell sites in R2Fe17Cx have larger values, which is strongly related to their largest magnetic moment and Wigner-Seitz atomic cell volume. The roles of the carbon atoms in increasing the Curie temperatures of the R2Fe17 compounds are attributed to the increased separation of Fe hexagons. The R2Fe17 and R2Fe14B phases with magnetic rare earth ions also show anisotropies of thermal expansion above c. For R2Fe17 and R2Fe14B the a a/a c > 1 whereas the anisotropy is reversed with the interstitial carbon in R2Fe17. The average bond magnetostrain is shown to be a possible predictor of the magnetic moment of Fe sites in the compounds. Both of the theoretical and

  12. Development of alkaline fuel cells.

    Energy Technology Data Exchange (ETDEWEB)

    Hibbs, Michael R.; Jenkins, Janelle E.; Alam, Todd Michael; Janarthanan, Rajeswari; Horan, James L.; Caire, Benjamin R.; Ziegler, Zachary C.; Herring, Andrew M.; Yang, Yuan; Zuo, Xiaobing; Robson, Michael H.; Artyushkova, Kateryna; Patterson, Wendy; Atanassov, Plamen Borissov

    2013-09-01

    This project focuses on the development and demonstration of anion exchange membrane (AEM) fuel cells for portable power applications. Novel polymeric anion exchange membranes and ionomers with high chemical stabilities were prepared characterized by researchers at Sandia National Laboratories. Durable, non-precious metal catalysts were prepared by Dr. Plamen Atanassovs research group at the University of New Mexico by utilizing an aerosol-based process to prepare templated nano-structures. Dr. Andy Herrings group at the Colorado School of Mines combined all of these materials to fabricate and test membrane electrode assemblies for single cell testing in a methanol-fueled alkaline system. The highest power density achieved in this study was 54 mW/cm2 which was 90% of the project target and the highest reported power density for a direct methanol alkaline fuel cell.

  13. Adsorption properties of ultradispersed powders of aluminum alloys with rare-earth metals, before and after water treatment

    Science.gov (United States)

    Ryabina, A. V.; Shevchenko, V. G.; Eselevich, D. A.

    2014-10-01

    Adsorption of nitrogen on Al-3% La, Al-1.5% Sc, and Al-3% Ce powders before and after processing with water in the relative pressure range p/p s = 10˜3 to 0.999 is experimentally studied at a temperature of 78 K. It is shown that the interaction between ultradispersed powder and water depends on the properties of the original powder, including the original content and composition of the oxide-hydroxide phases in the surface layers of metal particles, and the length and conditions of storage. Results confirming that processing powders containing rare-earth metals with water at room temperature leads to the formation of new phases and affects their morphology are presented. It is shown that the nanopores formed between crystallites on the surface of the particles during oxidation with water and subsequent thermal dehydration play an important role in the properties of powders processed with water. The specific surface and the porosity of powders are calculated.

  14. Oxides Catalysts of Rare Earth and Transient Metal for Catalytic Oxidation of Benzene

    Institute of Scientific and Technical Information of China (English)

    Liang Kun; Li Rong; Chen Jianjun; Ma Jiantai

    2004-01-01

    The catalysts of CeO2 and the mixture of CeO2 and CuO were prepared, and the activities of these catalysts for completely oxidizing benzene were studied.The results show that the optimal proportion of CeO2/CuO is 6: 4.The highest temperature at which benzene was completely oxidized on these catalysts at different airspeed was measured.Compared these catalysts with the noble metal used, our catalysts had superiority in the resources and the industrial cost besides good activities.

  15. Up-conversion processes of rare earth ions in heavy metal glasses

    Institute of Scientific and Technical Information of China (English)

    L. Grobelny; W A. Pisarski; J. Pisarska; R. Lisiecki; W. Ryba-Romanowski

    2011-01-01

    Heavy metal lead germanate glasses doubly doped with Yb3+ and Ln3+ ions (Ln=Er,Tm) were investigated.Up-conversion spectra of Er3+ and Tm3+ were registered under diode-laser excitation of Yb3+.Up-conversion luminescence bands corresponded to 4S3/2→4I15/2 (green)and 4F9/2→4I15/2 (red) transitions of Er3+ as well as 1G4→3H6 (blue) and 3H4→3H6 (NIR) transitions of Tm3+,respectively.

  16. 中温商业SCR催化剂碱和碱土中毒特性研究%Study on alkali and alkaline earths poisoning characteristics for a commercial SCR catalyst

    Institute of Scientific and Technical Information of China (English)

    沈伯雄; 卢凤菊; 高兰君; 岳时吉

    2016-01-01

    The poisoning of a commercial selective catalytic reduction ( SCR ) catalysts by alkali ( K ) and alkaline earths ( Ca) has been simulated in the laboratory. The techniques of N2 adsorption, scanning electronic microscopy, X-ray photoelectron spectroscopy, NH3-temperature program desorption, H2-temperature program reduction were used to identify the changes of physical chemical characteristics of the catalysts before and after the simulated poisoning. The results indicated that the poisoning of K and Ca did not damage the basic pore structure of the SCR catalyst, but decreased the BET surface area and pore volume. The poisoning by K and Ca changed the chemical valence state of V and decreased the reducibility of V. The poisoning by K and Ca decreased the amount of chemically adsorbed oxygen on the catalyst surface as well as acidity of the catalysts. The poisoning by K and Ca lowered the SCR activity of the catalysts and the poisoning by Ca was more serious than K.%在实验室条件下对选择性催化还原( SCR)商业催化剂的碱( K)和碱土( Ca)中毒进行了模拟,并采用液氮吸附、扫描电镜、能谱分析、NH3-程序升温脱附、H2-程序升温还原等方法对催化剂中毒前后的物理化学性质变化进行了表征。结果表明, K和Ca的中毒没有破坏商业中温SCR催化剂孔的基本结构,但K和Ca的中毒使催化剂的比表面积和孔容减小。 K和Ca的中毒在一定程度上改变了催化剂表面钒的价态,导致了钒的还原能力减弱,同时降低催化剂表面化学吸附氧。钾中毒和钙中毒使催化剂的表面酸量降低。钾和钙中毒造成中温SCR催化剂的脱硝活性降低,并且Ca中毒造成的催化剂活性降低要明显高于K中毒。

  17. Chemical composition of modern and fossil hippopotamid teeth and implications for paleoenvironmental reconstructions and enamel formation – Part 2: Alkaline earth elements as tracers of watershed hydrochemistry and provenance

    Directory of Open Access Journals (Sweden)

    I. Ssemmanda

    2012-11-01

    Full Text Available This study demonstrates that alkaline earth elements in enamel of hippopotamids, in particular Ba and Sr, are tracers for water provenance and hydrochemistry in terrestrial settings. The studied specimens are permanent premolar and molar teeth found in modern and fossil lacustrine sediments of the Western Branch of the East African Rift system (Lake Kikorongo, Lake Albert, and Lake Malawi and from modern fluvial environments of the Nile River. Concentrations in enamel vary by two orders of magnitude for Ba (120–9336 μg g−1 as well as for Sr (9–2150 μg g−1. The variations are partially induced during post-mortem alteration and during amelogenesis, but the major contribution originates ultimately from the variable water chemistry in the habitats of the hippopotamids which is controlled by the lithologies and weathering processes in the watershed areas. Amelogenesis causes a distinct distribution of MgO, Ba and Sr in modern and fossil enamel, in that element concentrations increase along profiles from the outer rim towards the enamel–dentin junction by a factor of 1.3–1.9. These elements are well correlated in single specimens, thus suggesting that their distribution is determined by a common, single process, which can be described by closed system Rayleigh crystallization of bioapatite in vivo. Enamel from most hippopotamid specimens has Sr/Ca and Ba/Ca which are typical for herbivores. However, Ba/Sr ranges from 0.1 to 3 and varies on spatial and temporal scales. Thus, Sr concentrations and Ba/Sr in enamel differentiate between habitats having basaltic mantle rocks or Archean crustal rocks as the ultimate sources of Sr and Ba. This provenance signal is modulated by climate change. In Miocene to Pleistocene enamel from the Lake Albert region, Ba/Sr decreases systematically with time from 2 to 0.5. This trend can be correlated with changes in climate from humid to arid, in vegetation from C3 to C4 biomass as well as with increasing

  18. Alkaline Capacitors Based on Nitride Nanoparticles

    Science.gov (United States)

    Aldissi, Matt

    2003-01-01

    High-energy-density alkaline electrochemical capacitors based on electrodes made of transition-metal nitride nanoparticles are undergoing development. Transition- metal nitrides (in particular, Fe3N and TiN) offer a desirable combination of high electrical conductivity and electrochemical stability in aqueous alkaline electrolytes like KOH. The high energy densities of these capacitors are attributable mainly to their high capacitance densities, which, in turn, are attributable mainly to the large specific surface areas of the electrode nanoparticles. Capacitors of this type could be useful as energy-storage components in such diverse equipment as digital communication systems, implanted medical devices, computers, portable consumer electronic devices, and electric vehicles.

  19. Preparation of rare-earth metal complex oxide catalysts for catalytic wet air oxidation

    Institute of Scientific and Technical Information of China (English)

    LI Ning; LI Guangming; YAO Zhenya; ZHAO Jianfu

    2007-01-01

    Catalytic wet air oxidation(CWAO)is one of the most promising technologies for pollution abatement.Developing catalysts with high activity and stability is crucial for the application of the CWAO process.The Mn/Ce complex oxide catalyrsts for CWAO of high concentration phenol containing wastewater were prepared by coprecipitation.The catalyst preparation conditions were optimized by using an orthogonal layout method and single-factor experimental analysis.The Mn/Ce serial catalysts were characterized by Brunauer-Emmett-Teller(BET)analysis and the metal cation leaching was measured by inductively coupled plasma torch-atomic emission spectrometry(ICP-AES).The results show that the catalysts have high catalytic activities even at a low temperature(80℃)and low oxygen partial pressure(0.5 MPa)in a batch reactor.The metallic ion leaching is comparatively low(Mn<6.577 mg/L and Ce<0.6910 mg/L,respectively)in the CWAO process.The phenol,CODCD and TOC removal efficiencies in the solution exceed 98.5% using the optimal catalyst(named CSP).The new catalyst would have a promising application in CWAO treatment of high concentration organic wastewater.

  20. Alkaline solution neutralization capacity of soil.

    Science.gov (United States)

    Asakura, Hiroshi; Sakanakura, Hirofumi; Matsuto, Toshihiko

    2010-10-01

    Alkaline eluate from municipal solid waste (MSW) incineration residue deposited in landfill alkalizes waste and soil layers. From the viewpoint of accelerating stability and preventing heavy metal elution, pH of the landfill layer (waste and daily cover soil) should be controlled. On the other hand, pH of leachate from existing MSW landfill sites is usually approximately neutral. One of the reasons is that daily cover soil can neutralize alkaline solution containing Ca(2+) as cation. However, in landfill layer where various types of wastes and reactions should be taken into consideration, the ability to neutralize alkaline solutions other than Ca(OH)(2) by soil should be evaluated. In this study, the neutralization capacities of various types of soils were measured using Ca(OH)(2) and NaOH solutions. Each soil used in this study showed approximately the same capacity to neutralize both alkaline solutions of Ca(OH)(2) and NaOH. The cation exchange capacity was less than 30% of the maximum alkali neutralization capacity obtained by the titration test. The mechanism of neutralization by the pH-dependent charge can explain the same neutralization capacities of the soils. Although further investigation on the neutralization capacity of the soils for alkaline substances other than NaOH is required, daily cover soil could serve as a buffer zone for alkaline leachates containing Ca(OH)(2) or other alkaline substances.

  1. Alkali metal – yttrium borohydrides: The link between coordination of small and large rare-earth

    Energy Technology Data Exchange (ETDEWEB)

    Sadikin, Yolanda [Department of Quantum Matter Physics, Laboratory of Crystallography, University of Geneva, Quai Ernest-Ansermet 24, CH-1211 Geneva (Switzerland); Stare, Katarina [Department of Quantum Matter Physics, Laboratory of Crystallography, University of Geneva, Quai Ernest-Ansermet 24, CH-1211 Geneva (Switzerland); Faculty of Chemistry and Chemical Technology, University of Ljubljana, Aškerjeva 5, SI-1000 Ljubljana (Slovenia); Schouwink, Pascal [Department of Quantum Matter Physics, Laboratory of Crystallography, University of Geneva, Quai Ernest-Ansermet 24, CH-1211 Geneva (Switzerland); Brix Ley, Morten; Jensen, Torben R. [Center for Materials Crystallography (CMC), Interdisciplinary Nanoscience Center (iNANO), and Department of Chemistry, Aarhus University, Langelandsgade 140, DK-8000 Århus C (Denmark); Meden, Anton [Faculty of Chemistry and Chemical Technology, University of Ljubljana, Aškerjeva 5, SI-1000 Ljubljana (Slovenia); Černý, Radovan, E-mail: radovan.cerny@unige.ch [Department of Quantum Matter Physics, Laboratory of Crystallography, University of Geneva, Quai Ernest-Ansermet 24, CH-1211 Geneva (Switzerland)

    2015-05-15

    The system Li–A–Y–BH{sub 4} (A=K, Rb, Cs) is found to contain five new compounds and four further ones known from previous work on the homoleptic borohydrides. Crystal structures have been solved and refined from synchrotron X-ray powder diffraction, thermal stability of new compounds have been investigated and ionic conductivity measured for selected samples. Significant coordination flexibility for Y{sup 3+} is revealed, which allows the formation of both octahedral frameworks and tetrahedral complex anions with the tetrahydroborate anion BH{sub 4} both as a linker and terminal ligand. Bi- and trimetallic cubic double-perovskites c-A{sub 3}Y(BH{sub 4}){sub 6} or c-A{sub 2}LiY(BH{sub 4}){sub 6} (A=Rb, Cs) form in all the investigated systems, with the exception of the Li–K–Y system. The compounds with the stoichiometry AY(BH{sub 4}){sub 4} crystallize in all investigated systems with a great variety of structure types which find their analog amongst metal oxides. In-situ formation of a new borohydride – closo-borane is observed during decomposition of all double perovskites. - Graphical abstract: The system Li–A–Y–BH{sub 4} (A=K, Rb, Cs) is found to contain five novel compounds and four further ones previously reported. Significant coordination flexibility of Y{sup 3+} is revealed, which can be employed to form both octahedral frameworks and tetrahedral complex anions, very different structural topologies. Versatility is also manifested in three different simultaneously occurring coordination modes of borohydrides for one metal cation, as proposed by DFT optimization of the monoclinic KY(BH{sub 4}){sub 4} structural model observed by powder diffraction. - Highlights: • The system Li-A-Y-BH{sub 4} (A=K, Rb, Cs) contains nine compounds in total. • Y{sup 3+} forms octahedral frameworks and tetrahedral complex anions. • Bi- and trimetallic double-perovskites crystallize in most systems. • Various AY(BH{sub 4}){sub 4} crystallize with

  2. Observational evidence for a metal rich atmosphere on the super-Earth GJ1214b

    CERN Document Server

    Désert, Jean-Michel; Kempton, Eliza Miller-Ricci; Berta, Zachory K; Charbonneau, David; Irwin, Jonathan; Fortney, Jonathan J; Burke, Christopher J; Nutzman, Philip

    2011-01-01

    We report observations of two consecutive transits of the warm super-Earth exoplanet GJ1214b at 3.6 and 4.5 microns with the Infrared Array Camera instrument on-board the Spitzer Space Telescope. The two transit light curves allow for the determination of the transit parameters for this system. We find these paremeters to be consistent with the previously determined values and no evidence for transit timing variations. The main investigation consists of measuring the transit depths in each bandpass to constrain the planet's transmission spectrum. Fixing the system scale and impact parameters, we measure R_p/R_star=0.1176 (+0.0008/-0.0009) and 0.1163 (+0.0010/-0.0008) at 3.6 and 4.5 microns, respectively. Combining these data with the previously reported MEarth Observatory measurements in the red optical yields constraints on the GJ1214b's transmission spectrum and allows us to rule-out a cloud-free, solar composition (i.e., hydrogen-dominated) atmosphere at 4.5 sigma confidence. This independently confirms a ...

  3. Visible-Light Excitated Photocatalytic Activity of Rare Earth Metal-Ion-Doped Titania

    Institute of Scientific and Technical Information of China (English)

    谢一兵; 李萍; 袁春伟

    2002-01-01

    The rare earth ion Ce4+ doped TiO2 was prepared by sol-gel method. The average particle sizes are about 10 nm for sol phase and 55 nm for polycrystalline phase. The photocatalytic activities to degrade Reactive Brilliant Red Dye X-3B were investigated. The result reveals that the spectrum response of Ce4+-TiO2 has extended to visible region from the UV region(λ<387 nm) of pure TiO2. Amorphous phase Ce4+-TiO2 sol with an electron scavenger (1.0% atom fraction Ce4+ ion doping amount) shows the capability of the photocatalytic degradation of the dye X-3B as well as the nanocrystallite Ce4+-TiO2 with an interband trap site. Despite of the difference in the morphology of Ce4+-TiO2 photocatalyst, there is no apparent difference in respect of the decoloring effects. Whereas, polycrystalline phase Ce4+-TiO2 exhibits strong photomineralization power in comparison with the amorphous phase. The photocatalytic oxidation mechanisms of the dye molecule mainly involved in the self-photo-sensitization photolysis process by the first excited singlet oxygen (1O2) and photocatalysis process by hydroxyl radicals(*OH) under visible light irradiation.

  4. A geological reconnaissance of electrical and electronic waste as a source for rare earth metals.

    Science.gov (United States)

    Mueller, Sandra R; Wäger, Patrick A; Widmer, Rolf; Williams, Ian D

    2015-11-01

    The mining of material resources requires knowledge about geogenic and anthropogenic deposits, in particular on the location of the deposits with the comparatively highest concentration of raw materials. In this study, we develop a framework that allows the establishment of analogies between geological and anthropogenic processes. These analogies were applied to three selected products containing rare earth elements (REE) in order to identify the most concentrated deposits in the anthropogenic cycle. The three identified anthropogenic deposits were characterised according to criteria such as "host rock", "REE mineralisation" and "age of mineralisation", i.e. regarding their "geological" setting. The results of this characterisation demonstrated that anthropogenic deposits have both a higher concentration of REE and a longer mine life than the evaluated geogenic deposit (Mount Weld, Australia). The results were further evaluated by comparison with the geological knowledge category of the United Nations Framework Classification for Fossil Energy and Mineral Reserves and Resources 2009 (UNFC-2009) to determine the confidence level in the deposit quantities. The application of our approach to the three selected cases shows a potential for recovery of REE in anthropogenic deposits; however, further exploration of both potential and limitations is required.

  5. Synthesis and structure of some nano-sized rare-earth metal ions doped potassium hexacyanoferrates

    Science.gov (United States)

    Narayan, Himanshu; Alemu, Hailemichael; Nketsa, Pusetso F.; Manatha, Toka J.; Madhavi Thakurdesai, And

    2015-05-01

    Rare-earth ions doped potassium hexacyanoferrates (KR-HCF); with the general formula KRFe(CN)6 · 3H2 O [with, R≡Y, Gd and Yb] nanoparticles were synthesized through precipitation. Characterization was done through particle-size analyzer, scanning electron microscopy (SEM), Fourier Transform infra-red (FTIR) and Raman spectroscopy, and powder X-ray diffraction (XRD). The XRD data was analyzed on FullProf Software Suite program and the unit-cell structure and lattice parameters of KR-HCF samples were determined from scratch and refined further. All the three KR-HCF nanoparticles seem to crystallize in the orthorhombic primitive PMMM space-group. Reasonably good agreement was found with the previously reported lattice constants of KGd-HCF and KYb-HCF orthorhombic single-crystals, except that they assume different space-groups. The observed dissimilarity of space-groups may be attributed to the different time scales involved in the synthesis process. Moreover, the crystal structure of KYFe(CN)6 · 3H2 O nanoparticles is being reported for the very first time.

  6. Band gaps and photocurrent responses of two novel alkaline earth metal(II) complexes based on 4,5-di(4‧-carboxylphenyl)benzene

    Science.gov (United States)

    Meng, Jiang Ping; Yan, Zhi Shuo; Long, Ji Ying; Gong, Yun; Lin, Jian Hua

    2017-01-01

    By using a rigid dicarboxylate ligand, 4,5-di(4‧-carboxylphenyl)benzene (H2L), two complexes formulated as SrL(DMF)(H2O)·(CH3CN) (DMF=N,N‧-dimethylformamide) (1) and BaL(H2O)2 (2) were solvothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Complexes 1 and 2 display two-dimensional (2D) layer structures. The two complexes exhibit different electrochemical and photoelectrochemical properties. Their thermal stabilities, cyclic voltammograms, UV-vis absorption and diffuse reflectance spectra and photoluminescence properties have been investigated. The band structures, the total density of states (TDOS) and partial density of states (PDOS) of the two complexes were calculated by CASTEP program. Complex 2 exhibits much higher photocurrent density than complex 1. The Mott-Schottky plots reveal that complexes 1 and 2 both are p-type semiconductors, which are in agreement with their band structure calculations.

  7. Synthesis, Crystal Structure, and Nonlinear Optical Properties of a New Alkali and Alkaline Earth Metal Carbonate RbNa5Ca5(CO38

    Directory of Open Access Journals (Sweden)

    Qiaoling Chen

    2016-12-01

    Full Text Available A new nonlinear optical (NLO material, RbNa5Ca5(CO38, has been synthesized by the hydrothermal method. The crystal structure is established by single-crystal X-ray diffraction. RbNa5Ca5(CO38 crystallizes in the hexagonal crystal system with space group P63mc (No. 186. The structure of RbNa5Ca5(CO38 can be described as the adjacent infinite [CaCO3]∞ layers lying in the a-b plane bridged through standing-on-edge [CO3] groups by sharing O atoms (two-fold coordinated to build a framework with four types of tunnels running through the b-axis. The Rb, Na, and [Na0.67Ca0.33] atoms reside in these tunnels, respectively. The measurement of second harmonic generation (SHG indicated that RbNa5Ca5(CO38 is a phase-matchable material, which had SHG responses of approximately 1×KH2PO4 (KDP. Meanwhile, the results from the UV-VIS diffuse reflectance spectroscopy study of the powder samples indicated that the UV cut-off edges of RbNa5Ca5(CO38 is about 203 nm.

  8. Syntheses, structures and characteristics of four alkaline-earth metal-organic frameworks (MOFs) based on benzene-1,2,4,5-tetracarboxylicacid and its derivative ligand

    Science.gov (United States)

    Du, Shunfu; Ji, Chunqing; Xin, Xuelian; Zhuang, Mu; Yu, Xuying; Lu, Jitao; Lu, Yukun; Sun, Daofeng

    2017-02-01

    Two new pillar-layered Ba(II)-based 3D frameworks and two new Ca(II)-based 3D supramolecular frameworks, [Ba2(dbtec)(H2O)2]n (1), [Ca2(dbtec)(H2O)8]n (2), {[Ba2(H2btec)·H2O]·0.5H2O}n (3) and [Ca(H2btec)·H2O]n (4) (H4dbtec = 3,6-dibromobenzene-1,2,4,5-tetracarboxylic acid; H4btec = benzene-1,2,4,5-tetracarboxylic acid), have been synthesized under similar reaction conditions and stoichiometry. Single crystal X-ray diffraction study reveals axial-orientation Br···π supramolecular interactions exist in the crystal structure of 1, which keeps an 3D binodal network with the (32.412.510.62.72)(32.46.56.6)2 topology. Whereas in 2, intramolecular and intermolecular H-bonding interactions with the ligated water molecules promote the formation of 3D supramolecular frameworks network. For 3, a new 3D 3-nodal network occurs in the structure and some rare coordination modes for the H4btec are observed. There is a 2D double layer with the thickness of 7.60 Å in 4. In addition, besides the high thermal stability, the FTIR spectra, PXRD patterns and the photoluminescent of these compounds are also discussed.

  9. Solid-state (79/81)Br NMR and gauge-including projector-augmented wave study of structure, symmetry, and hydration state in alkaline earth metal bromides.

    Science.gov (United States)

    Widdifield, Cory M; Bryce, David L

    2010-02-11

    Bromine-79/81 solid-state NMR (SSNMR) spectroscopy is established as a tool to characterize the local structure and symmetry about bromide ions in inorganic systems. Benchmark experimental (79/81)Br SSNMR data are acquired for CaBr(2), SrBr(2), BaBr(2), MgBr(2).6H(2)O, SrBr(2).6H(2)O, BaBr(2).2H(2)O, and CaBr(2).xH(2)O using the Solomon echo and/or QCPMG pulse sequences in magnetic fields of 11.75 and 21.1 T. Analytical line-shape analysis provides (79/81)Br electric field gradient (EFG) tensor parameters (including (79)Br quadrupolar coupling constants, C(Q)((79)Br), of up to 75.1(5) MHz in CaBr(2)), chemical shift tensor parameters (including the largest reported anisotropy), and the relative orientation of the tensor principal axis systems. These data are interpreted in terms of structure and symmetry. Our results indicate that ionic bromide systems should be generally accessible to characterization by (79/81)Br SSNMR despite sizable quadrupolar interactions. The resolving capabilities of (79/81)Br SSNMR spectroscopy are illustrated, using samples which possess up to four magnetically inequivalent sites, and through a rare example of (79)Br magic-angle spinning NMR for a Br in a noncubic lattice. Bromine-79/81 SSNMR spectroscopy is demonstrated to be sensitive to the presence of hydrates (i.e., pseudopolymorphism), via drastic changes in C(Q) and delta(iso). The changes are diagnostic to an extent that the composition of the mixture CaBr(2).xH(2)O is determined for the first time. This technique should therefore be applicable to characterize other unknown mixtures or polymorphs. Important instances where (79)Br nuclear quadrupole resonance data were found to be deficient are noted and corrected. GIPAW DFT computations are shown to be generally in very good agreement with the experimental (79/81)Br SSNMR observations. Finally, it is demonstrated that the origin of the EFG at the Br nuclei cannot be described quantitatively using a point charge model, even after including Sternheimer antishielding effects.

  10. Experimental investigation of the partitioning of phosphorus between metal and silicate phases - Implications for the earth, moon and eucrite parent body

    Science.gov (United States)

    Newsom, H. E.; Drake, M. J.

    1983-01-01

    An experimental study is reported of the partitioning of Phosphorus between solid metal and basaltic silicate liquid as a function of temperature and oxygen fugacity and of the implications for the earth, moon and eucrite parent body (EPB). The relationship established between the partition coefficient and the fugacity is given at 1190 C by log D(P) = -1.12 log fO2 - 15.95 and by log D(P) = -1.53 log fO2 17.73 at 1300 C. The partition coefficient D(P) was determined, and it is found to be consistent with a valence state of 5 for P in the molten silicate. Using the determined coefficient the low P/La ratios of the earth, moon, and eucrites relative to C1 chondrites can be explained. The lowering of the P/La ratio in the eucrites relative to Cl chondrite by a factor of 40 can be explained by partitioning P into 20-25 wt% sulfur-bearing metallic liquid corresponding to 5-25% of the total metal plus silicate system. The low P/La and W/La ratios in the moon may be explained by the partitioning of P and W into metal during formation of a small core by separation of liquid metal from silicate at low degrees of partial melting of the silicates. These observations are consistent with independent formation of the moon and the earth.

  11. Mechanism of interaction relation between the rare-earth element Ce and impurity elements Pb and Bi in Ag-based filler metal

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The mechanism of interaction relation between the rare-earth element Ce and elements Pb and Bi in Ag-based filler metal has been studied. The results show that the compounds CePb and CeBi with high melting point can be easily produced between these three elements in the filler metal, which greatly limited the formation of the isolated phase Pb or Bi and also eliminated the bad effect of impurity elements Pb and Bi on the spreading property of Ag-based filler metal. The metallurgical and quantum-mechanical bond formation analysis show that a strong chemical affinity was existed between the rare-earth element Ce and impurity elements Pb and Bi, which was proved by the XRD analysis results.

  12. Role of vacancies, light elements and rare-earth metals doping in CeO2.

    Science.gov (United States)

    Shi, H; Hussain, T; Ahuja, R; Kang, T W; Luo, W

    2016-08-24

    The magnetic properties and electronic structures of pure, doped and defective cerium oxide (CeO2) have been studied theoretically by means of ab initio calculations based on the density function theory (DFT) with the hybrid HF/DFT technique named PBE0. Carbon (C), nitrogen (N), phosphorus (P), sulphur (S), lanthanum (La) and praseodymium (Pr) doped in CeO2 and CeO2 containing oxygen vacancies (Ov) were considered. Our spin-polarized calculations show that C, N, Pr dopants and Ov defects magnetize the non-magnetic CeO2 in different degree. The optical band gap related to photocatalysis for pure CeO2, corresponding to the ultraviolet region, is reduced obviously by C, N, S, Pr impurities and oxygen vacancies, shifting to the visible region and even further to the infrared range. Especially, N-, S- and Pr-doped CeO2 could be used to photocatalytic water splitting for hydrogen production. As the concentration of Ov increasing up to 5%, the CeO2 exhibits a half-metallic properties.

  13. Role of vacancies, light elements and rare-earth metals doping in CeO2

    Science.gov (United States)

    Shi, H.; Hussain, T.; Ahuja, R.; Kang, T. W.; Luo, W.

    2016-01-01

    The magnetic properties and electronic structures of pure, doped and defective cerium oxide (CeO2) have been studied theoretically by means of ab initio calculations based on the density function theory (DFT) with the hybrid HF/DFT technique named PBE0. Carbon (C), nitrogen (N), phosphorus (P), sulphur (S), lanthanum (La) and praseodymium (Pr) doped in CeO2 and CeO2 containing oxygen vacancies (Ov) were considered. Our spin-polarized calculations show that C, N, Pr dopants and Ov defects magnetize the non-magnetic CeO2 in different degree. The optical band gap related to photocatalysis for pure CeO2, corresponding to the ultraviolet region, is reduced obviously by C, N, S, Pr impurities and oxygen vacancies, shifting to the visible region and even further to the infrared range. Especially, N-, S- and Pr-doped CeO2 could be used to photocatalytic water splitting for hydrogen production. As the concentration of Ov increasing up to 5%, the CeO2 exhibits a half-metallic properties. PMID:27554285

  14. Highly Active Rare-Earth-Metal La-Doped Photocatalysts: Fabrication, Characterization, and Their Photocatalytic Activity

    Directory of Open Access Journals (Sweden)

    S. Anandan

    2012-01-01

    Full Text Available Efficient La-doped TiO2 photocatalysts were prepared by sol-gel method and extensively characterized by various sophisticated techniques. The photocatalytic activity of La-doped TiO2 was evaluated for the degradation of monocrotophos (MCPs in aqueous solution. It showed higher rate of degradation than pure TiO2 for the light of wavelength of 254 nm and 365 nm. The rate constant of TiO2 increases with increasing La loading and exhibits maximum rate for 1% La loading. The photocatalytic activities of La-doped TiO2 are compared with La-doped ZnO; the reaction rate of the former is ~1.8 and 1.1 orders higher than the latter for the lights of wavelength 254 nm and 365 nm, respectively. The relative photonic efficiency of La-doped TiO2 is relatively higher than La-doped ZnO and commercial photocatalysts. Overall, La-doped TiO2 is the most active photocatalyst and shows high relative photonic efficiencies and high photocatalytic activity for the degradation of MCP. The enhanced photocatalytic activity of La-doped TiO2 is mainly due to the electron trapping by lanthanum metal ions, small particle size, large surface area, and high surface roughness of the photocatalysts.

  15. Rare-earth metal hydrides supported by silicon-bridged boratabenzene fluorenyl ligands: synthesis, structure and reactivity.

    Science.gov (United States)

    Wang, Chunhong; Xiang, Li; Leng, Xuebing; Chen, Yaofeng

    2017-01-24

    The reactions of rare-earth metal benzyl complexes supported by silicon-bridged boratabenzene fluorenyl ligands with PhSiH3 in toluene gave the corresponding dinuclear hydrides [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}Ln(μ-H)(THF)]2 (3-Ln; Ln = La, Nd, Gd), wherein the rare-earth metal ions are linked by both silicon-bridged boratabenzene fluorenyl ligands and hydrido ligands. The reactivity of these hydrides toward unsaturated substrates was studied. Among these, alkynides [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}Ln(μ-CCPh)]2 (4-Ln; Ln = La, Nd) were obtained via the σ-bond metathesis reaction, when 3-Ln (Ln = La, Nd) was treated with phenylacetylene. While reacting with 3-hexyne, the mono-addition product [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}Ln]2(μ-H)[μ-C(Et)[double bond, length as m-dash]C(H)Et] (5-Ln; Ln = La, Nd) was formed. Further investigations on the reactivity of 3-La displayed that benzonitrile and tert-butyl isonitrile readily inserted into the La-H bonds, affording an azomethine complex [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}La{μ-N[double bond, length as m-dash]C(H)Ph}]2 (6-La) and an N-tert-butylformimidoyl complex [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}La{μ,η(2)-C(H)[double bond, length as m-dash]N(t)Bu}]2 (7-La), respectively. The reaction with N,N'-diisopropylcarbodiimide at room temperature or at 75 °C gave a dimeric complex [{μ-[Me2Si(C13H8)(C5H4BNEt2)]}La]2(μ-H)[μ-N((i)Pr)CHN((i)Pr)] (8-La) or a monomeric complex [Me2Si(C13H8)(C5H4BNEt2)]La[N((i)Pr)CHN((i)Pr)] (9-La), respectively.

  16. Anodes for alkaline electrolysis

    Science.gov (United States)

    Soloveichik, Grigorii Lev

    2011-02-01

    A method of making an anode for alkaline electrolysis cells includes adsorption of precursor material on a carbonaceous material, conversion of the precursor material to hydroxide form and conversion of precursor material from hydroxide form to oxy-hydroxide form within the alkaline electrolysis cell.

  17. Graphene oxide-rare earth metal-organic framework composites for the selective isolation of hemoglobin.

    Science.gov (United States)

    Liu, Jia-Wei; Zhang, Yue; Chen, Xu-Wei; Wang, Jian-Hua

    2014-07-09

    Graphene oxide-La(BTC)(H2O)6 (H3BTC=1,3,5-benzenetricarboxylic acid) metal organic framework composites (LaMOF-GOn, n = 1-6, corresponding to the percentage of GO at 1, 2, 3, 4, 5, and 10%) are prepared through a simple and large-scale method at room temperature. The obtained composites are characterized by ATR-FTIR spectra, SEM, XRD, TGA, and N2 adsorption-desorption isotherm. The presence of GO significantly changes the morphologies of the composites from spindly rectangular rods to irregular thick blocks and increases their surface area from 14.8 cm(2) g(-1) (LaMOFs) to 26.6 cm(2) g(-1) (LaMOF-GO3), whereas at the same time, the crystalline structure of La(BTC)(H2O)6 is maintained. As a novel solid-phase adsorbent the LaMOF-GO composite exhibits outstanding adsorption properties for proteins. The strong hydrophobic interaction, especially π-π interaction between protein and the composite, is the main driving force for protein adsorption. In particular, highly selective isolation of hemoglobin (Hb) is achieved by using LaMOF-GO3 composite as sorbent in 4 mM B-R buffer containing 0.05 mol L(-1) NaCl at pH 8. The retained Hb could be effectively recovered with a 1 mM B-R buffer at pH 10, giving rise to a recovery of 63%. The practical applicability of the LaMOF-GO3 composite is demonstrated by the selective adsorption of Hb from human whole blood, and SDS-PAGE assays indicate that Hb could be selectively isolated with high purity from biological samples of complex matrixes.

  18. Empirical links between trace metal cycling and marine microbial ecology during a large perturbation to Earth's carbon cycle

    Science.gov (United States)

    Owens, Jeremy D.; Reinhard, Christopher T.; Rohrssen, Megan; Love, Gordon D.; Lyons, Timothy W.

    2016-09-01

    Understanding the global redox state of the oceans and its cause-and-effect relationship with periods of widespread organic-carbon deposition is vital to interpretations of Earth's climatic and biotic feedbacks during periods of expanded oceanic oxygen deficiency. Here, we present a compilation of new and published data from an organic-rich locality within the proto-North Atlantic Ocean during the Cenomanian-Turonian boundary event that shows a dramatic drawdown of redox-sensitive trace elements. Iron geochemistry independently suggests euxinic deposition (i.e., anoxic and sulfidic bottom waters) for the entire section, thus confirming its potential as an archive of global marine metal inventories. In particular, depleted molybdenum (Mo) and vanadium (V) concentrations effectively record the global expansion of euxinic and oxygen-deficient but non-sulfidic waters, respectively. The V drawdown precedes the OAE, fingerprinting an expansion of oxygen deficiency prior to an expansion of euxinia. Molybdenum drawdown, in contrast, is delayed with respect to V and coincides with the onset of OAE2. Parallel lipid biomarker analyses provide evidence for significant and progressive reorganization of marine microbial ecology during the OAE in this region of the proto-North Atlantic, with the smallest relative eukaryotic contributions to total primary production occurring during metal-depleted intervals. This relationship may be related to decreasing supplies of enzymatically important trace elements. Similarly, box modeling suggests that oceanic drawdown of Mo may have approached levels capable of affecting marine nitrogen fixation. Predictions of possible nitrogen stress on eukaryotic production, locally and globally, are consistent with the low observed levels of Mo and a rise in 2-methylhopane index values during the peak of the OAE. At the same time, the environmental challenge presented by low dissolved oxygen and euxinia coincides with increased turnover rates of

  19. Novel synergism by complex ligands in solvent extraction of rare earth metals(III) with {beta}-diketones

    Energy Technology Data Exchange (ETDEWEB)

    Imura, H. [Department of Environmental Sciences, Faculty of Science, Ibaraki University, Mito 310-8512 (Japan)]. E-mail: imura@mx.ibaraki.ac.jp; Ebisawa, M. [Department of Environmental Sciences, Faculty of Science, Ibaraki University, Mito 310-8512 (Japan); Kato, M. [Department of Environmental Sciences, Faculty of Science, Ibaraki University, Mito 310-8512 (Japan); Ohashi, K. [Department of Environmental Sciences, Faculty of Science, Ibaraki University, Mito 310-8512 (Japan)

    2006-02-09

    The extraction of rare earth metals(III) (RE) with hexafluoroacetylacetone (Hhfa) and 2-thenoyltrifluoroacetone (Htta) was studied in the presence of some cobalt(III) chelates such as tris(acetylacetonato)cobalt(III), tris(4-isopropyltropolonato)cobalt(III), tris(8-quinolinolato)cobalt(III), tris(8-quinolinethiolato)cobalt(III), and tris(diethyldithiocarbamato)cobalt(III) in benzene or toluene. The synergistic enhancement of the extraction of RE, especially of lanthanum(III) was found in all the systems. Therefore, those cobalt(III) chelates act as synergists or complex ligands. The equilibrium analysis and IR spectroscopic study were performed to evaluate the present synergistic mechanism. It was found that the RE-{beta}-diketone chelates form 1:1 adducts, i.e., binuclear complexes, with the cobalt(III) chelates in the organic phase. The formation constants ({beta} {sub s,1}) were determined and compared with those reported previously. The spectroscopic studies demonstrated that adducts have two different structures with inner- and outer-sphere coordination. In the former the cobalt(III) chelate directly coordinated to the RE ion and displaced the coordinated water molecules. In the latter the hydrogen-bonding was formed between the coordinating oxygen or sulfur atoms of cobalt(III) chelate and hydrogen atoms of the coordinated water molecules in the RE-{beta}-diketone chelate. The types of the adducts are mainly due to the steric factors of the RE-{beta}-diketone chelates and the cobalt(III) chelates.

  20. Magnetic Resonance Imaging Distortion and Targeting Errors from Strong Rare Earth Metal Magnetic Dental Implant Requiring Revision.

    Science.gov (United States)

    Seong-Cheol, Park; Chong Sik, Lee; Seok Min, Kim; Eu Jene, Choi; Do Hee, Lee; Jung Kyo, Lee

    2016-12-22

    Recently, the use of magnetic dental implants has been re-popularized with the introduction of strong rare earth metal, for example, neodymium, magnets. Unrecognized magnetic dental implants can cause critical magnetic resonance image distortions. We report a case involving surgical failure caused by a magnetic dental implant. A 62-year-old man underwent deep brain stimulation for medically insufficiently controlled Parkinson's disease. Stereotactic magnetic resonance imaging performed for the first deep brain stimulation showed that the overdenture was removed. However, a dental implant remained and contained a neodymium magnet, which was unrecognized at the time of imaging; the magnet caused localized non-linear distortions that were the largest around the dental magnets. In the magnetic field, the subthalamic area was distorted by a 4.6 mm right shift and counter clockwise rotation. However, distortions were visually subtle in the operation field and small for distant stereotactic markers, with approximately 1-2 mm distortions. The surgeon considered the distortion to be normal asymmetry or variation. Stereotactic marker distortion was calculated to be in the acceptable range in the surgical planning software. Targeting errors, approximately 5 mm on the right side and 2 mm on the left side, occurred postoperatively. Both leads were revised after the removal of dental magnets. Dental magnets may cause surgical failures and should be checked and removed before stereotactic surgery. Our findings should be considered when reviewing surgical precautions and making distortion-detection algorithm improvements.

  1. Magnetic coupling at rare earth ferromagnet/transition metal ferromagnet interfaces: A comprehensive study of Gd/Ni.

    Science.gov (United States)

    Higgs, T D C; Bonetti, S; Ohldag, H; Banerjee, N; Wang, X L; Rosenberg, A J; Cai, Z; Zhao, J H; Moler, K A; Robinson, J W A

    2016-07-22

    Thin film magnetic heterostructures with competing interfacial coupling and Zeeman energy provide a fertile ground to study phase transition between different equilibrium states as a function of external magnetic field and temperature. A rare-earth (RE)/transition metal (TM) ferromagnetic multilayer is a classic example where the magnetic state is determined by a competition between the Zeeman energy and antiferromagnetic interfacial exchange coupling energy. Technologically, such structures offer the possibility to engineer the macroscopic magnetic response by tuning the microscopic interactions between the layers. We have performed an exhaustive study of nickel/gadolinium as a model system for understanding RE/TM multilayers using the element-specific measurement technique x-ray magnetic circular dichroism, and determined the full magnetic state diagrams as a function of temperature and magnetic layer thickness. We compare our results to a modified Stoner-Wohlfarth-based model and provide evidence of a thickness-dependent transition to a magnetic fan state which is critical in understanding magnetoresistance effects in RE/TM systems. The results provide important insight for spintronics and superconducting spintronics where engineering tunable magnetic inhomogeneity is key for certain applications.

  2. Rapid enrichment of rare-earth metals by carboxymethyl cellulose-based open-cellular hydrogel adsorbent from HIPEs template.

    Science.gov (United States)

    Zhu, Yongfeng; Wang, Wenbo; Zheng, Yian; Wang, Feng; Wang, Aiqin

    2016-04-20

    A series of monolithic open-cellular hydrogel adsorbents based on carboxymethylcellulose (CMC) were prepared through high internal phase emulsions (HIPEs) and used to enrich the rare-earth metals La(3+) and Ce(3+). The changes of pore structure, and the effects of pH, contact time, initial concentration on the adsorption performance were systematically studied. The results show that the as-prepared monolithic hydrogel adsorbents possess good open-cellular framework structure and have fast adsorption kinetics and high adsorption capacity for La(3+) and Ce(3+). The involved adsorption system can reach equilibrium within 30min and the maximal adsorption capacity is determined to be 384.62mg/g for La(3+) and 333.33mg/g for Ce(3+). Moreover, these porous hydrogel adsorbents show an excellent adsorptive reusability for La(3+) and Ce(3+) through five adsorption-desorption cycles. Such a pore hierarchy structure makes this monolithic open-cellular hydrogel adsorbent be an effective adsorbent for effective enrichment of La(3+) and Ce(3+) from aqueous solution.

  3. First-principles prediction of the magnetism of 4f rare-earth-metal-doped wurtzite zinc oxide

    Institute of Scientific and Technical Information of China (English)

    AG El Hachimi; H Zaari; A Benyoussef; M El Yadari; A El Kenz

    2014-01-01

    Electronic structure and magnetic properties of wurtzite ZnO semiconductor doped with rare earth (RE=La, Ce, Pr, Pm, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm and Yb) atoms were studied using spin-polarized density functional theory based on the full-potential linear augmented plane wave (FP-LAPW) method as implemented in the Wien2k code. In this approach the generalized gradient ap-proximation (GGA) was used for the exchange-correlation (XC) potential. Our results showed that the substitution of RE ions in ZnO induced spins polarized localized states in the band gap. Moreover, the studied DMSs compounds retained half metallicity at dopant concentration x=0.625%for most of the studied elements, with 100%spin polarization at the Fermi level (EF). The total magnetic moments of these compounds existed due to RE 4f states present at EF, while small induced magnetic moments existed on other non-magnetic atoms as well. Finally, the energy difference between far and near configurations was investigated. It was found that the room temperature ferromagnetism was possible for RE-doped ZnO at near configuration. Since the RE-RE separation was long enough (far configuration) for magnetic coupling, the system became paramagnetic or antiferromagnetic ground state.

  4. Influence of compound deoxidation of steel with Al, Zr, rare earth metals, and Ti on properties of heavy castings

    Directory of Open Access Journals (Sweden)

    J. Senberger

    2012-01-01

    Full Text Available Heavy steel castings deoxidized with aluminium are sometimes brittle intercrystalline failed during their service along primary grain boundaries what is initiated by aluminium nitrides and so called conchoidal fractures are formed. The tendency to forming the conchoidal fractures depends in particular on cooling rate (the casting modulus, aluminium and nitrogen contents in steel. During deoxidation, when manufacturing heavy castings, the elements with high affinity to nitrogen, zirconium or titanium, are added to steel that would decrease nitrogen activity by the bond on stable nitrides. The formation of stable nitrides should reduce the tendency of steel to the formation of conchoidal fractures. Deoxidation was thermodynamically analyzed at presence of the mentioned elements. For particular conditions a probable course of deoxidation was estimated at test castings. The deoxidation course was checked by microanalysis of deoxidation products (inclusions. For service and experimental castings the anticipated composition of inclusions was compared. It has been proved that in heavy castings with high aluminium contents in steel under studied conditions neither the addition of zirconium nor of titanium nor of rare earth metals will prevent the formation of conchoidal fractures.

  5. Alkaline battery operational methodology

    Science.gov (United States)

    Sholklapper, Tal; Gallaway, Joshua; Steingart, Daniel; Ingale, Nilesh; Nyce, Michael

    2016-08-16

    Methods of using specific operational charge and discharge parameters to extend the life of alkaline batteries are disclosed. The methods can be used with any commercial primary or secondary alkaline battery, as well as with newer alkaline battery designs, including batteries with flowing electrolyte. The methods include cycling batteries within a narrow operating voltage window, with minimum and maximum cut-off voltages that are set based on battery characteristics and environmental conditions. The narrow voltage window decreases available capacity but allows the batteries to be cycled for hundreds or thousands of times.

  6. Quantum mechanics and molecular dynamics simulations of complexation of alkaline-earth and lanthanide cations by poly-amino-carboxylate ligands; Simulations par mecanique quantique et dynamique moleculaire de la complexation de cations alcalino-terreux et lanthanides par des ligands polyaminocarboxylates

    Energy Technology Data Exchange (ETDEWEB)

    Durand, S

    1999-07-01

    Molecular dynamics (MD) simulations on lanthanide(III) and alkaline-earth(II) complexes with poly-amino-carboxylates (ethylene-diamino-tetra-acetate EDTA{sup 4-}, ethylene-diamino-tri-acetate-acetic acid EDTA(H){sup 3-}, tetra-aza-cyclo-dodecane-tetra-acetate DOTA{sup 4-}, methylene-imidine-acetate MIDA{sup 2-}) are reported. First, a consistent set of Lennard-Jones parameters for La{sup 3+}, Eu{sup 3+} and Lu{sup 3+} cations has been derived from free energy calculations in aqueous solution. Observed differences in hydration free energies, coordination distances and hydration numbers are reproduced. Then, the solution structures of 1:1 complexes of alkaline-earth and/or lanthanide cations with EDTA{sup 4-}, EDTA(H){sup 3-}, DOTA{sup 4-} and 1:2 complexes of lanthanide cations with MIDA{sup 2-} were studied by MD in water. In addition, free energy calculations were performed to study, for each ligand, the relative thermodynamic stabilities of complexes with Ca{sup 2+} vs Sr{sup 2+} and vs Ba{sup 2+} on the one hand, and with La{sup 3+} vs Eu{sup 3+} and vs Lu{sup 3+} on the other hand. Model does not take into account explicitly polarization and charge transfer. However, the results qualitatively agree with experimental complexation data (structure and selectivities). (author)

  7. Effect of Rare Earth Elements (Er, Ho) on Semi-Metallic Materials (ScN) in an Applied Electric Field

    Science.gov (United States)

    Kim, Hyunjung; Park, Yeonjoon; King, Glen C.; Lee, Kunik; Choi, Sang H.

    2012-01-01

    The development of materials and fabrication technology for field-controlled spectrally active optics is essential for applications such as membrane optics, filters for LIDARs, windows for sensors, telescopes, spectroscopes, cameras and flat-panel displays. The dopants of rare earth elements, in a host of optical systems, create a number of absorption and emission band structures and can easily be incorporated into many high quality crystalline and amorphous hosts. In wide band-gap semiconductors like ScN, the existing deep levels can capture or emit the mobile charges, and can be ionized with the loss or capture of the carriers which are the fundamental basis of concept for smart optic materials. The band gap shrinkage or splitting with dopants supports the possibility of this concept. In the present work, a semi-metallic material (ScN) was doped with rare earth elements (Er, Ho) and tested under an applied electric field to characterize spectral and refractive index shifts by either Stark or Zeeman Effect. These effects can be verified using the UV-Vis spectroscopy, the Hall Effect measurement and the ellipsometric spectroscopy. The optical band gaps of ScN doped with Er and doped with Ho were experimentally estimated as 2.33eV and 2.24eV ( 0.2eV) respectively. This is less than that of undoped ScN (2.5 0.2eV). The red-shifted absorption onset is a direct evidence for the decrease of band gap energy (Eg), and the broadening of valence band states is attributable to the doping cases. A decrease in refractive index with an applied field was observed as a small shift in absorption coefficient using a variable angle spectroscopic ellipsometer. In the presence of an electric field, mobile carriers are redistributed within the space charge region (SCR) to produce this electro-refractive effect. The shift in refractive index is also affected by the density and location of deep potential wells within the SCR. In addition, the microstructure change was observed by a TEM

  8. Uranium in alkaline rocks

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, M.; Wollenberg, H.; Strisower, B.; Bowman, H.; Flexser, S.; Carmichael, I.

    1978-04-01

    Geologic and geochemical criteria were developed for the occurrence of economic uranium deposits in alkaline igneous rocks. A literature search, a limited chemical analytical program, and visits to three prominent alkaline-rock localities (Ilimaussaq, Greenland; Pocos de Caldas, Brazil; and Powderhorn, Colorado) were made to establish criteria to determine if a site had some uranium resource potential. From the literature, four alkaline-intrusive occurrences of differing character were identified as type-localities for uranium mineralization, and the important aspects of these localities were described. These characteristics were used to categorize and evaluate U.S. occurrences. The literature search disclosed 69 U.S. sites, encompassing nepheline syenite, alkaline granite, and carbonatite. It was possible to compare two-thirds of these sites to the type localities. A ranking system identified ten of the sites as most likely to have uranium resource potential.

  9. In situ La, Ce, and Nd L-edge X-ray absorption fine structure study of an intermetallic metal hydride electrode in an operating alkaline battery

    Energy Technology Data Exchange (ETDEWEB)

    Tryk, D.A.; Bae, I.T.; Scherson, D. [Case Western Reserve Univ., Cleveland, OH (United States). Dept. of Chemistry; Antonio, M.R. [Argonne National Lab., IL (United States). Chemistry Division; Jordan, G.W.; Huston, E.L. [Energizer Power Systems, Gainesville, FL (United States)

    1995-05-01

    The X-ray absorption fine structure of a technologically important MmL{sub 5} intermetallic compound (Mm = La{sub 0.52}Ce{sub 0.34}Nd{sub 0.10}Pr{sub 0.04}, L{sub 5} Ni{sub 3.5}Ca{sub 0.8}Mn{sub 0.3}Al{sub 0.4}) in the form of a hydrogen storage cathode was recorded in situ in the region 5440-6290 eV using an electrochemical cell which is essentially a fully functioning alkaline battery. Significant differences were observed in the X-ray absorption near edge structure (XANES) of all of the absorption edges (La, Ce, and Nd) between the uncharged and fully charged states. In particular, a clear increase in the intensity of the La and Nd L{sub III}-edge resonances (due to 2P{sub 3/2} {r_arrow} 5d electronic transitions) was found upon charging the cell. This phenomenon was attributed to an increase in the density of empty d-like states near the Fermi level following hydrogen injection into the lattice. Furthermore, the behavior of the Ca L{sub II,III}-edges of this battery material upon charging was nearly the same as that observed for the gas phase hydrogenation of the Ce{sub 2}Fe{sub 17} and Ce{sub 2}Fe{sub 14}B intermetallics reported in the literature.

  10. Alkali cation specific adsorption onto fcc(111) transition metal electrodes.

    Science.gov (United States)

    Mills, J N; McCrum, I T; Janik, M J

    2014-07-21

    The presence of alkali cations in electrolyte solutions is known to impact the rate of electrocatalytic reactions, though the mechanism of such impact is not conclusively determined. We use density functional theory (DFT) to examine the specific adsorption of alkali cations to fcc(111) electrode surfaces, as specific adsorption may block catalyst sites or otherwise impact surface catalytic chemistry. Solvation of the cation-metal surface structure was investigated using explicit water models. Computed equilibrium potentials for alkali cation adsorption suggest that alkali and alkaline earth cations will specifically adsorb onto Pt(111) and Pd(111) surfaces in the potential range of hydrogen oxidation and hydrogen evolution catalysis in alkaline solutions.

  11. Rare earth metals influence on mechanical properties and crack resistance of GP240GH and G17CrMo5-5 cast steels

    Directory of Open Access Journals (Sweden)

    M. Gajewski

    2009-10-01

    Full Text Available This paper presents results of research on modification influence of REM on mechanical properties and crack resistance of GP240GH cast carbon steel and G17CrMo5-5 high-temperature cast steel. The tests have been performed on successive industrial melts. The rare earth metals were put into the ladle during tapping of heat melt from the furnace. Each time ca 2000 kg of liquid metals were modified. Because of this the amount of sulphur in the cast steel was decreased and the non-metallic inclusion morphology was significantly changed. There were tested mechanical properties (Re,Rm, plastic properties (A5,Z and impact strength (KV, and on the basis of the three-point bend test the KJC stress intensity factor was evaluated. It was noticed that the REM modification brings essential increase of impact strength as well as fracture toughness determined by KJC factor.

  12. Effects of Metal Ions and Organic Solvents on Alkaline Phosphatase from Rice-field Eel%金属离子·有机溶剂对黄鳝碱性磷酸酶的影响

    Institute of Scientific and Technical Information of China (English)

    黄毅; 唐云明

    2008-01-01

    [Objective]The mechanism of alkaline phcephatase(ALP) was studied to promote rice-field eel aquaculture industry. [Method] The effects of effectors such as multiple metal ions and organic solvents on ALP in viscera of rice-field eel. [ Result] Na+ and K+ didn't generate big influences on en-zyme activity ;Mg2+ and Ca2+ could promote ALP while Li+,Cu2+ and Zn2+ could restrain ALP enzyme activity. Both KPO2-4 and WO3-4 generated by en-zyme catalyzing disodium phenyl phosphate possessed strong inhibitory effects on emzyme, and 9.5 mmol/L HPO2-4 would make enzyme activity decline by 13% while 9.5 mmol/L WO3-4 would make enzyme decline by 34%. The inhibition types of them were both competitive inhibition on enzyme activity. The organic solvents such as methanol,ethanol,ethylene glycol,isopropanol all generated influences on ALP and the order according to their inhibitory effects was isopropanol > ethanol > methanol > ethylene glycol. [Conclusion] The influences of various effectors on ALP activity of rice-field eel were studied from dy-namics perspective to provide theoretical basis for further clarifying ALP mechanism.

  13. Ultrafast electron, lattice and spin dynamics on rare earth metal surfaces. Investigated with linear and nonlinear optical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Radu, I.E.

    2006-03-15

    This thesis presents the femtosecond laser-induced electron, lattice and spin dynamics on two representative rare-earth systems: The ferromagnetic gadolinium Gd(0001) and the paramagnetic yttrium Y(0001) metals. The employed investigation tools are the time-resolved linear reflectivity and second-harmonic generation, which provide complementary information about the bulk and surface/interface dynamics, respectively. The femtosecond laser excitation of the exchange-split surface state of Gd(0001) triggers simultaneously the coherent vibrational dynamics of the lattice and spin subsystems in the surface region at a frequency of 3 THz. The coherent optical phonon corresponds to the vibration of the topmost atomic layer against the underlying bulk along the normal direction to the surface. The coupling mechanism between phonons and magnons is attributed to the modulation of the exchange interaction J between neighbour atoms due to the coherent lattice vibration. This leads to an oscillatory motion of the magnetic moments having the same frequency as the lattice vibration. Thus these results reveal a new type of phonon-magnon coupling mediated by the modulation of the exchange interaction and not by the conventional spin-orbit interaction. Moreover, we show that coherent spin dynamics in the THz frequency domain is achievable, which is at least one order of magnitude faster than previously reported. The laser-induced (de)magnetization dynamics of the ferromagnetic Gd(0001) thin films have been studied. Upon photo-excitation, the nonlinear magneto-optics measurements performed in this work show a sudden drop in the spin polarization of the surface state by more than 50% in a <100 fs time interval. Under comparable experimental conditions, the time-resolved photoemission studies reveal a constant exchange splitting of the surface state. The ultrafast decrease of spin polarization can be explained by the quasi-elastic spin-flip scattering of the hot electrons among spin

  14. Cyclic peptides-assisted trans- port of metal ions across liquid-organic membrane

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The formation of alkali and alkaline-earth metal picrate complexes with cyclo(Pro-Gly)n ionophores (1, n = 3; 2, n = 4) can facilitate the migration of metal ions across a bulk liquid CH2Cl2 membrane. The migration behavior was studied by measuring the solution absorption at 356 nm, using a UV/Vis spectrophotometer, and the rates can be determined by comparing the initial absorption of donor solutions with the absorption of the corresponding receiver solutions as the function of time. It was found that cyclic peptide 1 shows higher transport activity for the studied alkali and alkaline-earth metal ions than compound 2, which is related to the backbone flexibility of the cyclic peptides. The findings in this work suggest that the rate of ionophore-facilitated ion transport depends not only on the ability of complex forma-tion in aqueous phase, but also on the ability of complex dissociation in organic phase.

  15. 9-Benzylidene-9H-fluorene Derivatives Linked to Monoaza- 15-crown-5: Synthesis and Metal Ion Sensing

    Institute of Scientific and Technical Information of China (English)

    曹靖; 李阳; 冯俊香

    2012-01-01

    Two kinds of novel styryl chemosensory 2-FMNC and 3-FMNC, were designed and synthesized by an apporiate introduction of 9-benzylidene-9H-fluorene group as fluorophore with the aim at avoiding photoisomerisation. These 9-benzylidene-9H-fluorene derivatives showed the similar selectivity and sensitivity upon addition of metal ions. The sensitivity of FMNC to alkaline earth metal ions was Ba2+〉 Sr2+〉Ca2+≈Mg2+.

  16. Application of maize tassel for the removal of Pb, Se, Sr, U and V from borehole water contaminated with mine wastewater in the presence of alkaline metals.

    Science.gov (United States)

    Zvinowanda, Caliphs M; Okonkwo, Jonathan O; Sekhula, Mahlatse M; Agyei, Nana M; Sadiku, Rotimi

    2009-05-30

    In this study, the removal of Pb(II) from aqueous solutions by tassel powder was studied and optimised. Batch experiments were conducted on simulated solutions using tassel powder adsorbent and the effects of contact time, pH and concentration on the extent of Pb (II) removal was studied. Equilibrium and kinetic models for Pb(II) sorption were developed by considering the effect of contact time and concentration at optimum pH 4 and fixed temperature(25 degrees C). The Freundlich model was found to describe the sorption energetics of Pb(II) on tassel more fully than the Langmuir. A maximum Pb(II) loading capacity of 333.3mg/g on tassel was obtained. The adsorption process could be well described by both the Langmuir and Freundlich isotherms with R(2) values of 0.957 and 0.972, respectively. The kinetic parameters were obtained by fitting data from the effect of contact time on adsorption capacity into the pseudo-first, pseudo-second-order and intra-particle diffusion equations. The kinetics of Pb(II) on tassel surface was well defined using linearity coefficients (R(2)) by pseudo-second-order (0.999), followed by pseudo-first-order (0.795) and lastly intra-particle diffusion (0.6056), respectively. The developed method was then applied to environmental samples taken from borehole waters contaminated with mine wastewater. The removal of Pb (ND-100%), Se (100%), Sr (5.41-59.0%), U (100%) and V (46.1-100%) was attained using tassel. The uptake of the metals from environmental samples was dependent on pH, ionic strength and levels of other competing species.

  17. The influence of organic structure and rare earth metal cation on the corrosion efficiency observed on AS1020 steel compared with La(4OHCin3

    Directory of Open Access Journals (Sweden)

    Marianne Seter

    2015-01-01

    Full Text Available Whilst the corrosion protection of steel in aqueous chloride environments by the rare earth inhibitor lanthanum 4-hydroxycinnamate is well known, the influence of the structural variation of the organic component as well as the nature of the metal centre has not previously been addressed. Herein we show that praseodymium 4-hydroxy cinnamate is comparable to its lanthanum counterpart in aqueous solution. On the other hand, cerium 4-hydroxycinnamate and lanthanum 2-hydroxycinnamate show poor corrosion protection performance while lanthanum 3-hydroxycinnamate provides a level of inhibition between these. These differences are shown to be related to the speciation in solution and are postulated to be linked to steric influences which are likely to affect the bonding environment within the rare earth compound itself, as well as its bonding with the steel substrate.

  18. CONDENSED MATTER: ELECTRONIC STRUCTURE, ELECTRICAL, MAGNETIC, AND OPTICAL PROPERTIES: Enhanced Laser Cooling of Rare-Earth-Ion-Doped Glass Containing Nanometer-Sized Metallic Particles

    Science.gov (United States)

    Jia, You-Hua; Zhong, Biao; Yin, Jian-Ping

    2009-03-01

    The enhanced laser cooling performance of rare-earth-ions-doped glasses containing small particles is predicted. This is achieved by the enhancement of local field around rare earth ions, owing to the surface plasmon resonance of small metallic particles. The role of energy transfer between ions and the particle is theoretical discussed. Depending on the particle size and the ion emission quantum efficiency, the enhancement of the absorption and the fluorescence is predicted. Moreover, taking Yb3+ -doped ZBLAN as example, the cooling power and heat-light converting efficiency are calculated. It is finally concluded that the absorption and the fluorescence are greatly enhanced in these composite materials, the cooling power is increased compared to the bulk material.

  19. Influence of rare-earth metal doping on the catalytic performance of CuO-CeO2 for the preferential oxidation of CO in excess hydrogen

    Institute of Scientific and Technical Information of China (English)

    Zhigang Liu; Renxian Zhou; Xiaoming Zheng

    2008-01-01

    Doping of different rare-earth metals(Pr,Nd,Y and La)had an evident influence on the catalytic performance of CuO-CeO2 for the preferential oxidation(PROX)Of CO in excess hydrogen.As for Pr,the doping enhanced the catalytic activity of CuO-CeO2 for PROX.For example,the CO conversion over the above catalyst for PROX was higher than 99%at 120℃.Especially.the doping of Pr widened the temperature window by 20℃ over CuO-CeO2 with 99%CO conversion.For Nd,Y and La,the doping depressed the catalytic activity of CuO-CeO2 for PROX.However,the doping of transition metals markedly improved the selectivity of CuO-CeO2 for PROX.

  20. Synergic effects of ion irradiations (La, Ce) and alkaline pretreatment (KOH) on hydriding kinetic property of a Mm–Ni based alloy

    Energy Technology Data Exchange (ETDEWEB)

    Abe, H., E-mail: abe.hiroshi10@jaea.go.jp [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Aone, S.; Morimoto, R.; Uchida, H. [Course of Applied Science, Graduate School of Engineering, Tokai University, 4-1-1 Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan)

    2013-12-15

    Highlights: •Ion irradiations by various ions onto a Mm–Ni based hydrogen storage alloy. •The generation of vacancy type defects by ion irradiations in the surface of a Mm–Ni based alloy. •The enhancement of the initial rate by the ion irradiations of the Mm surface. •The enhancement of the initial rate by an alkaline treatment of the Mm surface. -- Abstract: The ion beam irradiation is known to produce a high density of vacancy type defects in the surface region of a metal and found to be an effective method as a surface modification in order to enhance the hydriding rate of a metal. In this study, we examined synergic effects of both surface modifications of ion irradiations and alkaline treatment on the initial hydriding rate of a Mm–Ni based alloy. In this study, the irradiations by lanthanum (La) and cerium (Ce) ions combined with an alkaline KOH pretreatment were found much more effective in the enhancement of the initial hydriding rate compared with irradiations with other ions. This study reports the synergic effects of the surface modifications by the both the surface irradiations with rare earth ions of La and Ce, and an alkaline surface treatment on the hydriding kinetics.

  1. Tuning bad metal and non-Fermi liquid behavior in a Mott material: Rare-earth nickelate thin films.

    Science.gov (United States)

    Mikheev, Evgeny; Hauser, Adam J; Himmetoglu, Burak; Moreno, Nelson E; Janotti, Anderson; Van de Walle, Chris G; Stemmer, Susanne

    2015-11-01

    Resistances that exceed the Mott-Ioffe-Regel limit (known as bad metal behavior) and non-Fermi liquid behavior are ubiquitous features of the normal state of many strongly correlated materials. We establish the conditions that lead to bad metal and non-Fermi liquid phases in NdNiO3, which exhibits a prototype bandwidth-controlled metal-insulator transition. We show that resistance saturation is determined by the magnitude of Ni eg orbital splitting, which can be tuned by strain in epitaxial films, causing the appearance of bad metal behavior under certain conditions. The results shed light on the nature of a crossover to a non-Fermi liquid metal phase and provide a predictive criterion for Anderson localization. They elucidate a seemingly complex phase behavior as a function of film strain and confinement and provide guidelines for orbital engineering and novel devices.

  2. Metals and Rare Earth Elements in polar aerosol as specific markers of natural and anthropogenic aerosol sources areas and atmospheric transport processes

    Science.gov (United States)

    Giardi, Fabio; Becagli, Silvia; Caiazzo, Laura; Cappelletti, David; Grotti, Marco; Malandrino, Mery; Salzano, Roberto; Severi, Mirko; Traversi, Rita; Udisti, Roberto

    2016-04-01

    Metals and Rare Earth Elements (REEs) in the aerosol have conservative properties from the formation to the deposition and can be useful to identify and quantify their natural and anthropic sources and to study the atmospheric transport processes. In spite of their importance relatively little is known about metals and especially REEs in the Artic atmosphere due to their low concentration in such environment. The present work reports the first attempt to determine and interpret the behaviour of metals and REEs in polar aerosol at high temporal resolution. Daily PM10 samples of arctic atmospheric particulate were collected on Teflon filters, during six spring-summer campaigns, since 2010, in the laboratory of Gruvebadet in Ny Ålesund (78°56' N, 11°56' E, Svalbard Islands, Norway). Chemical analyses were carried out through Inductively Coupled Plasma Mass Spectrometer provided with a desolvation nebulizer inlet system, allowing to reduce isobaric interferences and thus to quantify trace and ultra-trace metals in very low concentration in the Arctic aerosol samples. The results are useful in order to study sources areas, transport processes and depositional effects of natural and anthropic atmospheric particulate reaching the Arctic from southern industrialized areas; moreover, the observed seasonal trends give information about the different impact of natural and anthropic emissions driven by phenomena such as the Arctic Haze and the melting of the snow. In particular Rare Earth Elements (often in the ppt range) can be considered as soil's fingerprints of the particulate source areas and their determination, together with air-mass backtrajectory analysis, allow to identify dust source areas for the arctic mineral aerosol.

  3. Simultaneous spectrophotometric determination of thorium and rare earth metals with m-carboxychlorophosphonazo (CPAmK) and cetylpyridinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Chunggin Hsu; Ximan Lian; Jiaomai Pan (East China Normal Univ., Shanghai, SH (China))

    1991-09-01

    Th and rare earth elements (REE) react with m-carboxychlorophosphonazo (CPAmK) in the absence of cetylpyridinium chloride (CPC) to form colour complexes. In the presence of CPC, REE-complexes are not formed because of micellar masking, while Th gives a more sensitive reaction with CPAmK. Most of the foreign ions are tolerated in considerable amounts; 360-1000-fold amounts of rare earths do not interfere with the determination of Th. The optimum conditions of the complex-formation reactions and the compositions of Th-CPAmK complexes are described. A simple method is proposed for simultaneous determination of Th and rare earths without previous separation. (author).

  4. A systemic study of stepwise chlorination-chemical vapor transport characteristics of pure rare earth oxides from Sc{sub 2}O{sub 3} to Lu{sub 2}O{sub 3} mediated by alkaline chlorides as complex former

    Energy Technology Data Exchange (ETDEWEB)

    Sun Yanhui [School of Chemistry and Environment, South China Normal University, Guangzhou 510631 (China)]. E-mail: sunyanhui0102@163.com; He Peng [Department of Ecology, School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Chen Huani [School of Chemistry and Environment, South China Normal University, Guangzhou 510631 (China)

    2007-08-30

    A systematic study has been carried out for the stepwise chlorination-chemical vapor transport (SC-CVT) characteristics of pure rare earth oxides from Sc{sub 2}O{sub 3} to Lu{sub 2}O{sub 3} mediated by the vapor complexes KLnCl{sub 4} and NaLnCl{sub 4} (Ln = Sc, Y and La-Lu) used NaCl and KCl as complex former, respectively. The results showed that the SC-CVT characteristics are similarly for NaCl and KCl as complex former, the main deposition temperature of the rare earth chlorides LnCl{sub 3} is in the increasing order ScCl{sub 3} < YCl{sub 3} < LaCl{sub 3}, and then with a systematically decreasing trend from the early lanthanide chlorides to the end one. The results also showed that the total transported amount of the produced chlorides is YCl{sub 3} > ScCl{sub 3}, and they are much higher than that of most lanthanoid chlorides. For lanthanoids, the total transported amount of chloride increases systematically from the early lanthanoid chlorides to the end one except for EuCl{sub 3} and GdCl{sub 3} mediated by KCl and NaCl as complex former, respectively, which showed the divergence effect of Gd in the total transport efficiency. But there are some differences in SC-CVT characteristics of pure rare earth oxide mediated by KCl and NaCl as complex former, that is the main deposition temperature region for the same rare earth element was lower for KCl than that for NaCl as complex former except for LaCl{sub 3}, CeCl{sub 3}, YbCl{sub 3} and LuCl{sub 3}, while the total transport amount of rare earth chloride for KCl as complex former is higher than that for NaCl except for LaCl{sub 3} and EuCl{sub 3}. More over, the discussion was carried out for Sc and Y on the one hand and the lanthanides contain 4f electron as another hand based on the 4f electron hybridization assumption. Further more, the transport characteristics of rare earth oxides with alkaline chlorides as complex former in this study were compared to that with AlCl{sub 3} as complex former.

  5. Alkaline broadening in Stars

    CERN Document Server

    De Kertanguy, A

    2015-01-01

    Giving new insight for line broadening theory for atoms with more structure than hydrogen in most stars. Using symbolic software to build precise wave functions corrected for ds;dp quantum defects. The profiles obtained with that approach, have peculiar trends, narrower than hydrogen, all quantum defects used are taken from atomic database topbase. Illustration of stronger effects of ions and electrons on the alkaline profiles, than neutral-neutral collision mechanism. Keywords : Stars: fundamental parameters - Atomic processes - Line: profiles.

  6. Ground-state oxygen holes and the metal-insulator transition in the negative charge-transfer rare-earth nickelates

    Science.gov (United States)

    Bisogni, Valentina; Catalano, Sara; Green, Robert J.; Gibert, Marta; Scherwitzl, Raoul; Huang, Yaobo; Strocov, Vladimir N.; Zubko, Pavlo; Balandeh, Shadi; Triscone, Jean-Marc; Sawatzky, George; Schmitt, Thorsten

    2016-10-01

    The metal-insulator transition and the intriguing physical properties of rare-earth perovskite nickelates have attracted considerable attention in recent years. Nonetheless, a complete understanding of these materials remains elusive. Here we combine X-ray absorption and resonant inelastic X-ray scattering (RIXS) spectroscopies to resolve important aspects of the complex electronic structure of rare-earth nickelates, taking NdNiO3 thin film as representative example. The unusual coexistence of bound and continuum excitations observed in the RIXS spectra provides strong evidence for abundant oxygen holes in the ground state of these materials. Using cluster calculations and Anderson impurity model interpretation, we show that distinct spectral signatures arise from a Ni 3d8 configuration along with holes in the oxygen 2p valence band, confirming suggestions that these materials do not obey a conventional positive charge-transfer picture, but instead exhibit a negative charge-transfer energy in line with recent models interpreting the metal-insulator transition in terms of bond disproportionation.

  7. Robust and Porous β-Diketiminate-Functionalized Metal–Organic Frameworks for Earth-Abundant-Metal-Catalyzed C–H Amination and Hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Thacker, Nathan C.; Lin, Zekai; Zhang, Teng; Gilhula, James C.; Abney, Carter W.; Lin, Wenbin (UC)

    2016-05-27

    We have designed a strategy for postsynthesis installation of the β-diketiminate (NacNac) functionality in a metal–organic framework (MOF) of UiO-topology. Metalation of the NacNac-MOF (I) with earth-abundant metal salts afforded the desired MOF-supported NacNac-M complexes (M = Fe, Cu, and Co) with coordination environments established by detailed EXAFS studies. The NacNac-Fe-MOF catalyst, I•Fe(Me), efficiently catalyzed the challenging intramolecular sp3 C–H amination of a series of alkyl azides to afford α-substituted pyrrolidines. The NacNac-Cu-MOF catalyst, I•Cu(THF), was effective in promoting the intermolecular sp3 C–H amination of cyclohexene using unprotected anilines to provide access to secondary amines in excellent selectivity. Finally, the NacNac-Co-MOF catalyst, I•Co(H), was used to catalyze alkene hydrogenation with turnover numbers (TONs) as high as 700 000. All of the NacNac-M-MOF catalysts were more effective than their analogous homogeneous catalysts and could be recycled and reused without a noticeable decrease in yield. The NacNac-MOFs thus provide a novel platform for engineering recyclable earth-abundant-element-based single-site solid catalysts for many important organic transformations.

  8. From Geochemistry to Biochemistry: Simulating Prebiotic Chemistry Driven by Geochemical Gradients in Alkaline Hydrothermal Vents

    Science.gov (United States)

    Barge, Laurie

    2016-07-01

    Planetary water-rock interfaces generate energy in the form of redox, pH, and thermal gradients, and these disequilibria are particularly focused in hydrothermal vent systems where the reducing, heated hydrothermal fluid feeds back into the more oxidizing ocean. Alkaline hydrothermal vents have been proposed as a likely location for the origin of life on the early Earth due to various factors: including the hydrothermal pH / Eh gradients that resemble the ubiquitous electrical / proton gradients in biology, the catalytic hydrothermal precipitates that resemble inorganic catalysts in enzymes, and the presence of electron donors and acceptors in hydrothermal systems (e.g. H2 + CH4 and CO2) that are thought to have been utilized in the earliest metabolisms. Of particular importance for the emergence of metabolism are the mineral "chimneys" that precipitate at the vent fluid / seawater interface. Hydrothermal chimneys are flow-through chemical reactors that form porous and permeable inorganic membranes transecting geochemical gradients; in some ways similar to biological membranes that transect proton / ion gradients and harness these disequilibria to drive metabolism. These emergent chimney structures in the far-from-equilibrium system of the alkaline vent have many properties of interest to the origin of life that can be simulated in the laboratory: for example, they can generate electrical energy and drive redox reactions, and produce catalytic minerals (in particular the metal sulfides and iron oxyhydroxides - "green rust") that can facilitate chemical reactions towards proto-metabolic cycles and biosynthesis. Many of the factors prompting interest in alkaline hydrothermal vents on Earth may also have been present on early Mars, or even presently within icy worlds such as Europa or Enceladus - thus, understanding the disequilibria and resulting prebiotic chemistry in these systems can be of great use in assessing the potential for other environments in the Solar

  9. Molecular early main group metal hydrides: synthetic challenge, structures and applications.

    Science.gov (United States)

    Harder, Sjoerd

    2012-11-25

    Within the general area of early main group metal chemistry, the controlled synthesis of well-defined metal hydride complexes is a rapidly developing research field. As group 1 and 2 metal complexes are generally highly dynamic and lattice energies for their [MH](∞) and [MH(2)](∞) salts are high, the synthesis of well-defined soluble hydride complexes is an obvious challenge. Access to molecular early main group metal hydrides, however, is rewarding: these hydrocarbon-soluble metal hydrides are highly reactive, have found use in early main group metal catalysis and are potentially also valuable molecular model systems for polar metal hydrides as a hydrogen storage material. The article focusses specifically on alkali and alkaline-earth metal hydride complexes and discusses the synthetic challenge, molecular structures, reactivity and applications.

  10. Alkaline polymer electrolyte fuel cells: Principle, challenges, and recent progress

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Polymer electrolyte membrane fuel cells (PEMFC) have been recognized as a significant power source in future energy systems based on hydrogen. The current PEMFC technology features the employment of acidic polymer electrolytes which, albeit superior to electrolyte solutions, have intrinsically limited the catalysts to noble metals, fundamentally preventing PEMFC from widespread deployment. An effective solution to this problem is to develop fuel cells based on alkaline polymer electrolytes (APEFC), which not only enable the use of non-precious metal catalysts but also avoid the carbonate-precipitate issue which has been troubling the conventional alkaline fuel cells (AFC). This feature article introduces the principle of APEFC, the challenges, and our research progress, and focuses on strategies for developing key materials, including high-performance alkaline polyelectrolytes and stable non-precious metal catalysts. For alkaline polymer electrolytes, high ionic conductivity and satisfactory mechanical property are difficult to be balanced, therefore polymer cross-linking is an ultimate strategy. For non-precious metal catalysts, it is urgent to improve the catalytic activity and stability. New materials, such as transition-metal complexes, nitrogen-doped carbon nanotubes, and metal carbides, would become applicable in APEFC.

  11. Titanium corrosion in alkaline hydrogen peroxide environments

    Science.gov (United States)

    Been, Jantje

    1998-12-01

    The corrosion of Grade 2 titanium in alkaline hydrogen peroxide environments has been studied by weight loss corrosion tests, electrochemical impedance spectroscopy (EIS), linear polarization resistance (LPR) measurements and potentiodynamic polarography. Calcium ions and wood pulp were investigated as corrosion inhibitors. In alkaline peroxide, the titanium corrosion rate increased with increasing pH, temperature, and hydrogen peroxide concentration. The corrosion controlling mechanism is thought to be the reaction of the oxide with the perhydroxyl ion. No evidence of thermodynamically stable calcium titanate was found in the surface film of test coupons exposed to calcium-inhibited alkaline peroxide solutions. Calcium inhibition is probably the result of low local alkali and peroxide concentrations at the metal surface produced by reaction of adsorbed calcium with hydrogen peroxide. It has been shown that the inhibiting effect of calcium is temporary, possibly through an effect of calcium on the chemical and/or physical stability of the surface oxide. Pulp is an effective and stable corrosion inhibitor. Raising the pulp concentration decreased the corrosion rate. The inhibiting effect of pulp may be related to the adsorption and interaction of the pulp fibers with H 2O2, thereby decreasing the peroxide concentration and rendering the solution less corrosive. The presence of both pulp and calcium led to higher corrosion rates than obtained by either one inhibitor alone. Replacement of hydrofluoric acid with alkaline peroxide for pickling of titanium was investigated. Titanium corrosion rates in alkaline peroxide exceeded those obtained in the conventional hydrofluoric acid bath. General corrosion was observed with extensive roughening of the surface giving a dull gray appearance. Preferred dissolution of certain crystallographic planes was investigated through the corrosion of a titanium single crystal. Whereas the overall effect on the corrosion rate was small

  12. Effect of H2O on metal-silicate partitioning of Ni, Co, V, Cr, Mn and Fe: Implications for the oxidation state of the Earth and Mars

    Science.gov (United States)

    Clesi, V.; Bouhifd, M. A.; Bolfan-Casanova, N.; Manthilake, G.; Fabbrizio, A.; Andrault, D.

    2016-11-01

    This study investigates the metal-silicate partitioning of Ni, Co, V, Cr, Mn and Fe during core mantle differentiation of terrestrial planets under hydrous conditions. For this, we equilibrated a molten hydrous CI chondrite model composition with various Fe-rich alloys in the system Fe-C-Ni-Co-Si-S in a multi-anvil over a range of P, T, fO2 and water content (5-20 GPa, 2073-2500 K, from 1 to 5 log units below the iron-wüstite (IW) buffer and for XH2O varying from 500 ppm to 1.5 wt%). By comparing the present experiments with the available data sets on dry systems, we observes that the effect of water on the partition coefficients of moderately siderophile elements is only moderate. For example, for iron we observed a decrease in the partition coefficient of Fe (Dmet/silFe) from 9.5 to 4.3, with increasing water content of the silicate melt, from 0 to 1.44 wt%, respectively. The evolution of metal-silicate partition coefficients of Ni, Co, V, Cr, Mn and Fe are modelled based on sets of empirical parameters. These empirical models are then used to refine the process of core segregation during accretion of Mars and the Earth. It appears that the likely presence of 3.5 wt% water on Mars during the core-mantle segregation could account for ∼74% of the FeO content of the Martian mantle. In contrast, water does not play such an important role for the Earth; only 4-6% of the FeO content of its mantle could be due to the water-induced Fe-oxidation, for a likely initial water concentration of 1.8 wt%. Thus, in order to reproduce the present-day FeO content of 8 wt% in the mantle, the Earth could initially have been accreted from a large fraction (between 85% and 90%) of reducing bodies (similar to EH chondrites), with 10-15% of the Earth's mass likely made of more oxidized components that introduced the major part of water and FeO to the Earth. This high proportion of enstatite chondrites in the original constitution of the Earth is consistent with the 17O,48Ca,50Ti,62Ni

  13. Metal ion binding with carbon nanotubes and graphene: Effect of chirality and curvature

    Science.gov (United States)

    Umadevi, Deivasigamani; Sastry, G. Narahari

    2012-10-01

    First principles calculations have been used to comprehensively study the binding of a series alkali (Li+, Na+, K+) and alkaline earth (Be2+, Mg2+, Ca2+) metal ions with carbon nanotubes (CNTs) and graphene. It is interesting to note that the mono-cationic systems prefer binding to armchair CNTs over zigzag CNTs, while the preference for the di-cationic systems is exactly opposite. We have also observed significant changes in the HOMO-LUMO energy gap of the CNTs on metal ion binding and these results indicate that the fine tuning of energy gap of the CNTs can be effected through metal ion binding.

  14. 二价碱土金属氟化物对Er3+/Tm3+/Yb3+共掺氟氧锗酸盐玻璃热稳定性和光谱特性影响的研究%Effect of Bivalent Alkaline Earth Fluorides Introduction on Thermal Stability and Spectroscopic Properties of Er3+/Tm3+/Yb3+ Co-Doped Oxyfluorogermanate Glasses

    Institute of Scientific and Technical Information of China (English)

    胡曰博; 张新娜; 周大利; 焦清; 王荣飞; 黄劲峰; 龙晓波; 邱建备

    2012-01-01

    制备了分别含有MgF2,CaF2,SrF2或BaF2的Er3+/Tm3+/Yb3+共掺氟氧锗酸盐玻璃试样和包含BaF2纳米晶的玻璃陶瓷试样,所制备试样均具有良好的透光性.对试样的热稳定性和上转换发光特性进行了研究.通过分析试样的吸收光谱发现,随着所含二价阳离子原子量的增大,试样的紫外吸收截止波长明显向短波方向移动.结果显示:通过改变所含二价碱土金属离子的种类能够对激发光的颜色进行调节,特别值得关注的是Mg2+的影响;结果证实:通过对包含二价碱土金属的玻璃进行微晶化处理或者增加二价碱土金属的含量均能提高上转换发光的强度.%Transparent Er3+ /Tm3+ /Yb3+ co-doped oxyfluorogermanate glasses alone containing MgF2, CaF2, SrF2 or BaF2 and nano-glass-ceramics only containing BaF2 were prepared. The thermal stabilities and the up-conversion emission properties of the samples were investigated. Analyses of absorbance spectra reveal that the UV cutoff band moves slightly to shortwave band with the doping bivalent cation mass increasing. The results show that the emission color can be adjusted by changing the alkaline earth cation species in the glass matrixes, especially as Mg2+ is concerned, and the emission intensity can increase notably by heating the glass containing alkaline-earth fluoride into glass ceramic containing alkaline-earth fluoride nanocrystals or increasing the content of bivalent alkaline earth fluorides.

  15. Potency of (doped) rare earth oxide particles and their constituent metals to inhibit algal growth and induce direct toxic effects.

    Science.gov (United States)

    Joonas, Elise; Aruoja, Villem; Olli, Kalle; Syvertsen-Wiig, Guttorm; Vija, Heiki; Kahru, Anne

    2017-03-27

    Use of rare earth elements (REEs) has increased rapidly in recent decades due to technological advances. It has been accompanied by recurring rare earth element anomalies in water bodies. In this work we (i) studied the effects of eight novel doped and one non-doped rare earth oxide (REO) particles (aimed to be used in solid oxide fuel cells and gas separation membranes) on algae, (ii) quantified the individual adverse effects of the elements that constitute the (doped) REO particles and (iii) attempted to find a discernible pattern to relate REO particle physicochemical characteristics to algal growth inhibitory properties. Green algae Raphidocelis subcapitata (formerly Pseudokirchneriella subcapitata) were used as a test species in two different formats: a standard OECD201 algal growth inhibition assay and the algal viability assay (a 'spot test') that avoids nutrient removal effects. In the 24h 'spot' test that demonstrated direct toxicity, algae were not viable at REE concentrations above 1mgmetal/L. 72-hour algal growth inhibition EC50 values for four REE salts (Ce, Gd, La, Pr) were between 1.2 and 1.4mg/L, whereas the EC50 for REO particles ranged from 1 to 98mg/L. The growth inhibition of REEs was presumably the result of nutrient sequestration from the algal growth medium. The adverse effects of REO particles were at least in part due to the entrapment of algae within particle agglomerates. Adverse effects due to the dissolution of constituent elements from (doped) REO particles and the size or specific surface area of particles were excluded, except for La2NiO4. However, the structure of the particles and/or the varying effects of oxide composition might have played a role in the observed effects. As the production rates of these REO particles are negligible compared to other forms of REEs, there is presumably no acute risk for aquatic unicellular algae.

  16. Investigation of Surfactant-Stain-Metal Interaction: Naphthochrome Green/Cetyltrimethylammonium Bromide/Rare Earths Ternary Complexation

    Institute of Scientific and Technical Information of China (English)

    郑立新; 沈荣; 郜洪文

    2003-01-01

    The ternary interaction of naphthochrome green (NCG) with cetyltrimethylammonium bromide (CTAB) and rare earths (Res: Yb, Dy, Er and Eu) has been investigated with the microsurface adsorption-spectral correction technique (MSASC). The aggregation of NCG on CTAB obeys the Langmuir isothermal adsorption. The enrichment of NCG on CTAB and the presence of NaCl sensitize the complexation between Res and NCG. Both the binary aggregate and the ternary complex were characterized in the presence and absence of NaCl at pH 8.30 at 20 and 40℃.

  17. Universal behavior of chalcogenides of rare-earth metals in the transition to a state with intermediate valence at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Tsiok, O. B.; Khvostantsev, L. G.; Brazhkin, V. V., E-mail: brazhkin@hppi.troitsk.ru [Russian Academy of Sciences, Vereshchagin Institute of High-Pressure Physics (Russian Federation)

    2015-06-15

    Precision measurements of resistivity, thermopower, and volume are performed for TmS, TmSe, and TmTe under a hydrostatic pressure up to 8 GPa. Comparison of the transport properties and volume of TmTe and SmTe in the valence transition region demonstrates a complete analogy up to quantitative coincidence. It is shown that the thermopower of all thulium and samarium chalcogenides in the lattice collapse region and in subsequent rearrangement of the electron spectrum in a wide range of pressures follow a universal dependence corresponding the passage of the Fermi level through the peak of the density of states (DOS). The results are considered in the context of ideas about the exciton nature of the intermediate valence in chalcogenides of rare-earth metals.

  18. Assessment of metal, trace and rare earth element concentrations in a sedimentary profile from Ponte Nova reservoir, Sao Paulo state, Brazil, by NAA

    Energy Technology Data Exchange (ETDEWEB)

    Rocha, Flavio R.; Bordon, Isabella C.C.L.; Silva, Paulo S.C.; Favaro, Deborah I.T., E-mail: flavio@baquara.com, E-mail: defavaro@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Silva, Sharlleny A.; Franklin, Robson L.; Ferreira, Francisco J., E-mail: shasilva@sp.gov.br, E-mail: rfranklin@sp.gov.br [Companhia Ambiental do Estado de Sao Paulo (ELAI/CETESB), SP (Brazil). Setor de Quimica Inorganica

    2015-07-01

    Ponte Nova reservoir, located in the upper basin of the Tiete River in the southern region of Sao Paulo State, covers an area of 25.7 km{sup 2} and drains an area of 320 km{sup 2}. It was built in 1972 to control the rivers flow in the Metropolitan Region of Sao Paulo (MRSP) and water supply. A 30 cm sediment core was collected in the dam in August 2014, sliced at every 2.5 cm. Instrumental neutron activation analysis (INAA) was applied to the sediment samples to determine some major (Fe, K and Na), trace (As, Ba, Br, Co, Cr, Cs, Hf, Rb, Sb, Sc, Ta, Tb, Th, U and Zn) and rare earth (Ce, Eu, La, Lu, Nd, Sm, Tb and Yb) elements. The enrichment factor (EF) and Igeo were applied to the results by using NASC (North American Shale Composite) as reference values for sediment contamination index assessment. An EF>1.5 was obtained for As, Hf, Rb, Ta, Th, U, and rare earths Ce, Eu, La, Nd and Sm when NASC values were used, but only for Br, when the last layer concentration values were used as reference values. Similar results were obtained for the Igeo index. For semi-metal As and metals Cr and Zn concentration values were compared to oriented values from Environmental Canada (TEL and PEL) only Cr exceeded TEL value in some slices of the profile. These results may indicate that there is no anthropogenic contribution for the elements analyzed in this reservoir. Multivariate statistical analysis was applied to the results. (author)

  19. Nano-structured noble metal catalysts based on hexametallate architecture for the reforming of hydrocarbon fuels

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, Todd H.

    2015-09-15

    Nano-structured noble metal catalysts based on hexametallate lattices, of a spinel block type, and which are resistant to carbon deposition and metal sulfide formation are provided. The catalysts are designed for the reforming of hydrocarbon fuels to synthesis gas. The hexametallate lattices are doped with noble metals (Au, Pt, Rh, Ru) which are atomically dispersed as isolated sites throughout the lattice and take the place of hexametallate metal ions such as Cr, Ga, In, and/or Nb. Mirror cations in the crystal lattice are selected from alkali metals, alkaline earth metals, and the lanthanide metals, so as to reduce the acidity of the catalyst crystal lattice and enhance the desorption of carbon deposit forming moieties such as aromatics. The catalysts can be used at temperatures as high as 1000.degree. C. and pressures up to 30 atmospheres. A method for producing these catalysts and applications of their use also is provided.

  20. Diversity, metal resistance and uranium sequestration abilities of bacteria from uranium ore deposit in deep earth stratum.

    Science.gov (United States)

    Islam, Ekramul; Sar, Pinaki

    2016-05-01

    Metal resistance and uranium (U) sequestration abilities of bacteria residing in subsurface U ore was investigated using 122 pure culture strains isolated through enrichment. The cumulative frequencies of isolates resistant to each metal tested were as follows: As(V), 74%; Zn, 58%; Ni, 53%; Cd, 47%; Cr(VI), 41%; Co, 40%; Cu, 20%; and Hg, 4%. 16S rRNA gene analysis revealed that isolated bacteria belonged to 14 genera with abundance of Arthrobacter, Microbacterium, Acinetobacter and Stenotrophomonas. Cobalt did not interfere with the growth of most of the bacterial isolates belonging to different groups while U allowed growth of four different genera of which Stenotrophomonas and Microbacterium showed high U tolerance. Interestingly, tolerance to Ni, Zn, Cu, and Hg was observed only in Microbacterium, Arthrobacter, Paenibacillus¸ and Acinetobacter, respectively. However, Microbacterium was found to be dominant when isolated from other five different metal enrichments including U. Uranium removal study showed that 84% of the test bacteria could remove more than 50mgUg(-1) dry weight from 80 or 160mgL(-1) U within 48h. In general, Microbacterium, Arthrobacter and Acinetobacter could remove a higher amount of U. High resolution transmission electron microscopy (HRTEM) study of U exposed cells revealed that accumulated U sequestered mostly around the cell periphery. The study highlights that indigenous U ore deposit bacteria have the potential to interact with U, and thus could be applied for bioremediation of U contaminated sites or wastes.

  1. Syntheses, Characterization and Antitumour Activities of Rare Earth Metal Complexes with 2-(((4,6-dimethyl)-2-Pyrimidinyl)thio)-Acetic Acid

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Eight rare earth metal (Ⅲ) complexes with 2-(((4,6-dimethyl)-2-pyrimidinyl)thio)-acetic acid, LnL3*nH2O [HL=2-(((4,6-dimethyl)-2-pyrimidinyl)thio)-acetic acid; Ln=La, Ce, Pr, Nd, Sm Eu, Gd, Tb; n=4 or 5], were prepared and characterized by elemental analysis, complexometric titration, thermal analysis, conductivity, IR and 1H-NMR. The results reveal that carboxyl group of the ligand coordinates with rare earth ions in bidentate mode after deprotonated. The water molecules exist as crystal water in the complexes. The anti-tumour activities of HL and some complexes were tested by both the MTT and SRB methods. The results show that the suppression ratios of some complexes against the tested tumour cells (HL-60 human leukemia cell lines, BGC-823 human gastric carcinoma cell lines, hela human cervix adenocarcinoma cell lines and Bel-7402 human hepatic carcinoma cell lines) are superior to HL.

  2. An alkaline element

    Energy Technology Data Exchange (ETDEWEB)

    Arita, T.; Murakami, K.; Okha, K.

    1983-04-28

    A cathode with a dual layer active mass is installed in the disk shaped alkaline silver and zinc element. The first layer, which is turned towards the anode, contains 85 parts Ag2O, 5 parts electrolytic MnO2 and 10 parts graphite. The second layer, which contacts the bottom of the element, contains 35 parts Ag2O, 60 parts electrolytic MnO2 and 5 parts graphite. The electrical capacity of the first and second layers is 60 and 40, respectively. The first layer may be discharged with a high current density and the second layer with less current density. The element has high characteristics with comparatively low cost.

  3. Alkaline carbonates in blast furnace process

    Directory of Open Access Journals (Sweden)

    P. Besta

    2014-10-01

    Full Text Available The production of iron in blast furnaces is a complex of physical, chemical and mechanical processes. The input raw materials contain not only metallic components, but also a number of negative elements. The most important negative elements include alkaline carbonates. They can significantly affect the course of the blast furnace process and thus the overall performance of the furnace. As a result of that, it is essential to accurately monitor the alkali content in the blast furnace raw materials. The article analyzes the alkali content in input and output raw materials and their impact on the blast furnace process.

  4. Phase characteristics of rare earth elements in metallic fuel for a sodium-cooled fast reactor by injection casting

    Science.gov (United States)

    Kuk, Seoung Woo; Kim, Ki Hwan; Kim, Jong Hwan; Song, Hoon; Oh, Seok Jin; Park, Jeong-Yong; Lee, Chan Bock; Youn, Young-Sang; Kim, Jong-Yun

    2017-04-01

    Uranium-zirconium-rare earth (U-Zr-RE) fuel slugs for a sodium-cooled fast reactor were manufactured using a modified injection casting method, and investigated with respect to their uniformity, distribution, composition, and phase behavior according to RE content. Nd, Ce, Pr, and La were chosen as four representative lanthanide elements because they are considered to be major RE components of fuel ingots after pyroprocessing. Immiscible layers were found on the top layers of the melt-residue commensurate with higher fuel slug RE content. Scanning electron microscopy-energy-dispersive X-ray spectroscopy (SEM-EDS) data showed that RE elements in the melt-residue were distributed uniformly throughout the fuel slugs. RE element agglomeration did not contaminate the fuel slugs but strongly affected the RE content of the slugs.

  5. Ballmilling of metal borohydrides for hydrogen storage

    DEFF Research Database (Denmark)

    Sommer, Sanna

    2014-01-01

    is to hydrogenate simple compounds such as metalborides and hydrides with the intention of forming a new and more hydrogen rich borohydride. In contrast to mainstream research, the method of synthesis has been based on reactants that are expected to be found in the metal borohydride’s dehydrogenated state....... Specifically, the research undertaken targets CaB6 whose boron is in a octahedral network, or AlB2 whose boron is layered. These compounds were then reactive ball milled with alkali and alkaline earth metal under hydrogen pressure, with the intention of forming metal borohydrides. For CaB6, no clear sign...... Transform Infra-red Spectroscopy, Magic Angle Spinning Nuclear Magnetic Resonance, Thermal Gravimetry, Differential Scanning Calorimetry, Mass Spectroscopy and lastly In Situ Powder X-ray diffraction measurements at l711 MAXLab....

  6. Removal of ammonia from aqueous solutions by catalytic oxidation with copper-based rare earth composite metal materials: catalytic performance, characterization, and cytotoxicity evaluation

    Institute of Scientific and Technical Information of China (English)

    Chang-Mao Hung

    2011-01-01

    Ammonia (NH3) has an important use in the chemical industry and is widely found in industrial wastewater.For this investigation of copper-based rare earth composite metal materials,aqueous solutions containing 400 mg/L of ammonia were oxidized in a batch-bed reactor with a catalyst prepared by the co-precipitation of copper nitrate,lanthanum nitrate and cerium nitrate.Barely any of the dissolved ammonia was removed by wet oxidation without a catalyst,but about 88% of the ammonia was reduced during wet oxidation over the catalysts at 423 K with an oxygen partial pressure of 4.0 MPa.The catalytic redox behavior was determined by cyclic voltammetry (CV).Furthermore,the catalysts were characterized using thermogravimetric analyzer (TGA) and scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX),which showed that the catalytic behavior was related to the metal oxide properties of the catalyst.In addition,the copper-lanthanum-cerium composite-induced cytotoxicity in the human lung MRC-5 cell line was tested,and the percentage cell survival was determined by 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetra-zolium (MTS) analysis in vitro.No apparent cytotoxicity was observed when the human lung cells were exposed to the copper-lanthanum-cerium composite.

  7. Oxygen Evolution at Nickel Hydroxide Films Co-deposited Light Rare Earth Elements

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Composite nickel hydroxide films were prepared by cathodic co-electrodeposition from metal nitrate solution and characterized by cyclic voltammetry in 1.0 mol/L KOH solution. The codeposited light rare earth elements were lanthanum, cerium, praseodymium and neodymium. The films were analyzed by spectrophotometry and optical transmission. The results of the cyclic voltammetry in 1.0 mol/L KOH solution showed that the current density for oxygen evolution at the film electrode was affected by the co-deposited rare earth metal ions in the film. About 20 mA/cm2 increase of current density for oxygen evolution was found when the film was obtained from the solution with cerium (7% v/v) and nickel (93% v/v) nitrate. The effects of galvanostatic cathodic current density for the film formation on the oxygen evolution at the film electrodes from the alkaline were discussed.

  8. 生物活性稀土梯度涂层在碱液环境中的电极化后处理%Electric polarized post treatment of rare earth active bioceramic gradient coating in alkaline solution

    Institute of Scientific and Technical Information of China (English)

    汪震; 刘其斌; 肖明; 杨邦成

    2011-01-01

    To improve the quality of rare earth active bioceramic gradient coatings,a method of electric polarized treatment(PAS) was used to post-process the gradient coatings fabricated by wide band laser cladding in alkali liquid.The phases and corrosion resistance of the bioceramic coatings were analyzed by XRD and an electrochemical analyzer.The bioceramic coatings were immersed in simulated body fluid(SBF) to examine its bioactivity and its electrical charge.The experimental results indicate that PAS treatment not only improves the crystallinity of the coatings,but also is favourable to transform additional phases into hydroxyapatite.PAS treatment exhibits a little effect on corrosion resistance of the bioceramic coatings.Compared with as-received coatings,the coatings treated by PAS are of better bioactivity and more negative charge.%为了改善活性生物稀土梯度涂层的质量,在碱液环境中采用电极化处理法(PAS)对宽带激光熔覆生物活性稀土梯度涂层进行后处理。利用XRD和电化学分析仪对涂层的相组成和耐腐蚀性进行了研究,通过模拟体液浸泡试验考察了生物陶瓷涂层的生物活性和涂层表面的电荷分布情况。结果表明,碱液环境中电极化处理法(PAS)能够提高涂层的结晶度,使涂层中的非晶相、杂相向羟基磷灰石转化。PAS对涂层的耐腐蚀性影响不大。与未处理涂层相比,PAS处理后的涂层生物活性更好,且涂层表面产生了更多的负电荷。

  9. Iron complex-catalyzed ammonia-borane dehydrogenation. A potential route toward B-N-containing polymer motifs using earth-abundant metal catalysts.

    Science.gov (United States)

    Baker, R Tom; Gordon, John C; Hamilton, Charles W; Henson, Neil J; Lin, Po-Heng; Maguire, Steven; Murugesu, Muralee; Scott, Brian L; Smythe, Nathan C

    2012-03-28

    Ammonia-borane (NH(3)BH(3), AB) has garnered interest as a hydrogen storage material due to its high weight percent hydrogen content and ease of H(2) release relative to metal hydrides. As a consequence of dehydrogenation, B-N-containing oligomeric/polymeric materials are formed. The ability to control this process and dictate the identity of the generated polymer opens up the possibility of the targeted synthesis of new materials. While precious metals have been used in this regard, the ability to construct such materials using earth-abundant metals such as Fe presents a more economical approach. Four Fe complexes containing amido and phosphine supporting ligands were synthesized, and their reactivity with AB was examined. Three-coordinate Fe(PCy(3))[N(SiMe(3))(2)](2) (1) and four-coordinate Fe(DEPE)[N(SiMe(3))(2)](2) (2) yield a mixture of (NH(2)BH(2))(n) and (NHBH)(n) products with up to 1.7 equiv of H(2) released per AB but cannot be recycled (DEPE = 1,2-bis(diethylphosphino)ethane). In contrast, Fe supported by a bidentate P-N ligand (4) can be used in a second cycle to afford a similar product mixture. Intriguingly, the symmetric analogue of 4 (Fe(N-N)(P-P), 3), only generates (NH(2)BH(2))(n) and does so in minutes at room temperature. This marked difference in reactivity may be the result of the chemistry of Fe(II) vs Fe(0).

  10. Experimental and computational investigation of the group 11-group 2 diatomic molecules: First determination of the AuSr and AuBa bond energies and thermodynamic stability of the copper- and silver-alkaline earth species

    Science.gov (United States)

    Ciccioli, A.; Gigli, G.; Lauricella, M.

    2012-05-01

    The dissociation energies of the intermetallic molecules AuSr and AuBa were for the first time determined by the Knudsen effusion mass spectrometry method. The two species were produced in the vapor phase equilibrated with apt mixtures of the constituent elements, and the dissociation equilibria were monitored mass-spectrometrically in the temperature range 1406-1971 K (AuSr) and 1505-1971 K (AuBa). The third-law analysis of the equilibrium data gives the following dissociation energies (D_0°, in kJ/mol): 244.4 ± 4.8 (AuSr) and 273.3 ± 6.3 (AuBa), so completing the series of D_0°s for the AuAE (AE = group 2 element) diatomics. The AuAE species were also studied computationally at the coupled cluster including single, double and perturbative triple excitation [CCSD(T)] level with basis sets of increasing zeta quality, and various complete basis set limit extrapolations were performed to calculate the dissociation energies. Furthermore, the entire series of the heteronuclear diatomic species formed from one group 11 (Cu, Ag) and one group 2 (Be, Mg, Ca, Sr, Ba) metal was studied by DFT with the hybrid meta-GGA TPSSh functional and the def2-QZVPP basis set, selected after screening a number of functional-basis set combinations using the AuAE species as benchmark. Dissociation energies, internuclear distances, vibrational frequencies, and anharmonic constants were determined for the CuAE and AgAE species and their thermal functions evaluated therefrom. On this basis, a thermodynamic evaluation of the formation of these species was carried out under various conditions.

  11. Preconcentration of Rare Earth Elements with 8-Hydroxyquinoline-5-sulfonic Acid Chelated Cellulose Filter Prior to Determination by Inductively Coupled Plasma Atomic Emission Spectrometry

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    8-Hydroxyquinoline-5-sulfonic acid,covalently bound to filter cellulose,was used for preconcentrating trace rare earth element(REE) ions from complex matrices and matrix separation,respectively.Multi-REE ions were preconcentrated on the column filled with 8-hydroxyquinoline-5-sulfonic acid cellulose filter and analysed by ICP-AES after being eluted with dilute HNO3.In the given pH range,alkali and alkaline earth metal ions can be separated as matrix elements;a high concentration factor is obtained and the eluates can be measured without interference.The usefulness of the method is shown by the control analyses of standard reference materials.

  12. Adsorption and growth morphology of rare-earth metals on graphene studied by ab initio calculations and scanning tunneling microscopy

    Science.gov (United States)

    Liu, Xiaojie; Wang, C. Z.; Hupalo, M.; Yao, Y. X.; Tringides, M. C.; Lu, W. C.; Ho, K. M.

    2010-12-01

    Adsorption of rare-earth (RE) adatoms (Nd, Gd, Eu, and Yb) on graphene was studied by first-principles calculations based on the density-functional theory. The calculations show that the hollow site of graphene is the energetically favorable adsorption site for all the RE adatoms studied. The adsorption energies and diffusion barriers of Nd and Gd on graphene are found to be larger than those of Eu and Yb. Comparison with scanning tunneling microscopy experiments for Gd and Eu epitaxially grown on graphene confirms these calculated adsorption and barrier differences, since fractal-like islands are observed for Gd and flat-topped crystalline islands for Eu. The formation of flat Eu islands on graphene can be attributed to its low diffusion barrier and relatively larger ratio of adsorption energy to its bulk cohesive energy. The interactions between the Nd and Gd adatoms and graphene cause noticeable in-plane lattice distortions in the graphene layer. Adsorption of the RE adatoms on graphene also induces significant electric dipole and magnetic moments.

  13. Research into processes of production of hydrides of materials containing rare-earth metals and their corrosion

    Science.gov (United States)

    Sofronov, V. L.; Kartashov, E. Y.; Molokov, P. B.; Zhiganov, A. N.; Kalaev, M. E.

    2017-01-01

    Production of permanent magnets on basis of rare earth elements (REE) is implemented by means of powder metallurgy, therefore a technologically important operation is the multistage mechanical crushing of materials to the extent of domains. The promising technique of crushing of magnetic materials is their consistent hydrogenation-dehydrogenation that allows obtaining nano-dispersed powders which are stable enough in air. Hydrogenation apparatuses, as opposed to conventional grinding machines, do not comprise motion works and their producing capacity is much higher. Hydrogenation process does not require any additional preparation of materials and it excludes undermilling and overmilling as well as material oxidation. The paper presents the results of investigation on the temperature effect on the hydrogenation process of Nd-Fe alloys. The study results on the corrosion stability of ligature hydrides under various conditions are also given. Kinetic parameters of the hydrogenation process of ligatures are determined. The phase composition of corrosion products is detected. Guidelines on hydride powder storage are given.

  14. Role of Mononuclear Rare Earth Metal Complexes in Promoting the Hydrolysis of 2-Hydroxypropyl p-Nitrophenyl Phosphate

    Institute of Scientific and Technical Information of China (English)

    WANG Rui; LIN Hai; LIN Hua-Kuan

    2007-01-01

    Two long-chain multidentate ligands: 2,9-di-(n-2',5',8'-triazanonyl)-1,10-phenanthroline (L1) and 2,9-di-(n-4',7',10'-triazaundecyl)-1,10-phenanthroline (L2) were synthesized. The hydrolytic kinetics of 2-hydroxypropyl p-nitrophenyl phosphate (HPNP) catalyzed by the complexes of L1 or L2 with La(Ⅲ) or Gd(Ⅲ) have been studied lytic effect of GdL1 was the best among the four complexes for hydrolysis of HPNP. Its kLnLH-1, kLnL and pKa are structure of the ligands and the properties of the metal ions, and deduced the catalysis mechanism.

  15. Metal, trace and rare earth element assessment in a sedimentary profile from Promissao reservoir, Sao Paulo state, Brazil, by INAA

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Sharlleny A.; Franklin, Robson L., E-mail: shasilva@sp.gov.br [Companhia Ambiental do Estado de Sao Paulo (ELAI/CETESB), SP (Brazil). Setor de Quimica Inorganica; Luiz-Silva, Wanilson [Universidade Estadual de Campinas (DGRN/UNICAMP), SP (Brazil). Instituto de Geociencias. Departamento de Geologia e Recursos Naturais; Favaro, Deborah I.T., E-mail: defavaro@ipen.gov.br [Instituto de Pesquisas Energeticas e Nucleares (LAN/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Laboratorio de Analise por Ativacao Neutronica

    2015-07-01

    In the present study the preliminary results for the Promissao reservoir, situated in the Lower Tiete region covering a little more than 1% of the SP state population, is characterized by intense agropastoral activities. Its operations for generating electrical energy started in 1975. It is located at Tiete River and its hydrographic basin has a drainage area of 530 km{sup 2}. The total extension of the reservoir is 110 km along the Tiete River, with a medium depth of 20 m. A core sampler was used and a 33 cm sediment core was collected from the dam in January 2013, sliced at every 2.5 cm, totaling 13 samples. Instrumental neutron activation analysis was applied to the sediment samples in order to determine some major (Fe, K, and Na), trace (As, Ba, Br, Co, Cr, Cs, Hf, Rb, Sb, Sc, Ta, Tb, Th, U, and Zn) and rare earth elements (Ce, Eu, La, Lu, Nd, Sm, Tb, and Yb). The enrichment factor (EF) was applied to the results obtained by using North American Shale Composite, Upper Continental Crust and the concentration values of the last layer of this profile as reference values for sediment contamination index assessment. When the results for As, Cr, and Zn were compared to threshold effect level (TEL) and probable effect level (PEL) oriented values, sediments from 0-10 cm exceeded the TEL values for As (5.9 mg kg{sup -1}), all samples exceeded the PEL values for Cr (90 mg kg{sup -1}), and all samples had much lower values than TEL values for Zn (123 mg kg{sup -1}). (author)

  16. The capacity of hydrous fluids to transport and fractionate incompatible elements and metals within the Earth's mantle

    Science.gov (United States)

    Adam, John; Locmelis, Marek; Afonso, Juan Carlos; Rushmer, Tracy; Fiorentini, Marco L.

    2014-06-01

    silicate melts and aqueous fluids are thought to play critical roles in the chemical differentiation of the Earth's crust and mantle. Yet their relative effects are poorly constrained. We have addressed this issue by measuring partition coefficients for 50 trace and minor elements in experimentally produced aqueous fluids, coexisting basanite melts, and peridotite minerals. The experiments were conducted at 1.0-4.0 GPa and 950-1200°C in single capsules containing (either 40 or 50 wt %) H2O and trace element-enriched basanite glass. This allowed run products to be easily identified and analyzed by a combination of electron microprobe and LAM-ICP-MS. Fluid and melt compositions were reconstructed from mass balances and published solubility data for H2O in silicate melts. Relative to the basanite melt, the solutes from H2O-fluids are enriched in SiO2, alkalis, Ba, and Pb, but depleted in FeO, MgO, CaO, and REE. With increasing pressure, the mutual solubility of fluids and melts increases rapidly with complete miscibility between H2O and basanitic melts occurring between 3.0 and 4.0 GPa at 1100°C. Although LREE are favored over HREE in the fluid phase, they are less soluble than the HFSE (Nb, Ta, Zr, Hf, and Ti). Thus, the relative depletions of HFSE that are characteristic of arc magmas must be due to a residual phase that concentrates HFSE (e.g., rutile). Otherwise, H2O-fluids have the capacity to impart many of the geochemical characteristics that distinguish some rocks and melts from the deep mantle lithosphere (e.g., MARID and lamproites).

  17. Rare earth metal doped CeO2-based catalytic materials for diesel soot oxidation at lower temperatures

    Institute of Scientific and Technical Information of China (English)

    A Rangaswamy; Putla Sudarsanam; Benjaram M Reddy

    2015-01-01

    In this work, the influence of trivalent rare-earth dopants (Sm and La) on the structure-activity properties of CeO2 was thor-oughly studied for diesel soot oxidation. For this, an optimized 40%of Sm and La was incorporated into the CeO2 using a facile co-precipitation method from ultra-high dilute aqueous solutions. A systematic physicochemical characterization was carried out using X-ray diffraction (XRD), transmission electron microscopy (TEM), Brumauer-Emmett-teller method (BET) surface area, X-ray pho-toelectron spectroscopy (XPS), Raman, and H2-temperature programmed reduction (TPR) techniques. The soot oxidation efficiency of the catalysts was investigated using a thermogravimetric method. The XRD results suggested the formation of nanocrystalline sin-gle phase CeO2-Sm2O3 and CeO2-La2O3 solid solutions. The Sm-and La-doped CeO2 materials exhibited smaller crystallite size and higher BET surface area compared with the pure CeO2. Owing to the difference in the oxidation states of the dopants (Sm3+and La3+) and the Ce4+, a number of oxygen vacancies were generated in CeO2-Sm2O3 and CeO2-La2O3 samples. The H2-TPR studies evidenced the improved reducible nature of the CeO2-Sm2O3 and CeO2-La2O3 samples compared with the CeO2. It was found that the addition of Sm and La to the CeO2 outstandingly enhanced its catalytic efficiency for the oxidation of diesel soot. The observed 50%soot con-version temperatures for the CeO2-Sm2O3, CeO2-La2O3 and CeO2 were~790, 843 and 864 K (loose contact), respectively, and similar activity order was also found under the tight contact condition. The high soot oxidation efficacy of the CeO2-Sm2O3 sample was at-tributed to numerous catalytically favourable properties, like smaller crystallite size, larger surface area, abundant oxygen vacancies, and superior reducible nature.

  18. Accumulation of heavy metals in oil-contaminated peat soils

    Science.gov (United States)

    Vodyanitskii, Yu. N.; Savichev, A. T.; Trofimov, S. Ya.; Shishkonakova, E. A.

    2012-10-01

    X-ray fluorescence and X-ray radiometry represent easy and simple methods to determine concentrations of heavy metals in the ash of peat soils contaminated with oil and can be applied for soil monitoring purposes. Oil spills on peat bogs produce two contamination zones differing in the composition of heavy metals. In the zone of primary contamination, the peat surface is covered by a bitumen crust with V, Ni, Sr, Ba, Ce, and La accumulating there. This zone adjoins the zone of secondary peat contamination, where heavy alkaline-earth metals (Sr, Ba) and lanthanides (Ce and La) are accumulated to a lesser extent. Biological preparations recommended for remediation of oil-contaminated peat soils should be tolerant to high concentrations of heavy metals, particularly, V, Ni, and Ba that are present in the oil contaminated soils in relatively high amounts.

  19. Byproduct metals and rare-earth elements used in the production of light-emitting diodes—Overview of principal sources of supply and material requirements for selected markets

    Science.gov (United States)

    Wilburn, David R.

    2012-01-01

    The use of light-emitting diodes (LEDs) is expanding because of environmental issues and the efficiency and cost savings achieved compared with use of traditional incandescent lighting. The longer life and reduced power consumption of some LEDs have led to annual energy savings, reduced maintenance costs, and lower emissions of carbon dioxide, sulfur dioxide, and nitrogen oxides from powerplants because of the resulting decrease in energy consumption required for lighting applications when LEDs are used to replace less-energy-efficient sources. Metals such as arsenic, gallium, indium, and the rare-earth elements (REEs) cerium, europium, gadolinium, lanthanum, terbium, and yttrium are important mineral materials used in LED semiconductor technology. Most of the world's supply of these materials is produced as byproducts from the production of aluminum, copper, lead, and zinc. Most of the rare earths required for LED production in 2011 came from China, and most LED production facilities were located in Asia. The LED manufacturing process is complex and is undergoing much change with the growth of the industry and the changes in demand patterns of associated commodities. In many respects, the continued growth of the LED industry, particularly in the general lighting sector, is tied to its ability to increase LED efficiency and color uniformity while decreasing the costs of producing, purchasing, and operating LEDs. Research is supported by governments of China, the European Union, Japan, the Republic of Korea, and the United States. Because of the volume of ongoing research in this sector, it is likely that the material requirements of future LEDs may be quite different than LEDs currently (2011) in use as industry attempts to cut costs by reducing material requirements of expensive heavy rare-earth phosphors and increasing the sizes of wafers for economies of scale. Improved LED performance will allow customers to reduce the number of LEDs in automotive, electronic

  20. Magnesium substitutions in rare-earth metal germanides with the Gd5Si4 type. Synthesis, structure determination and magnetic properties of RE5-xMgxGe4 (RE=Gd-Tm, Lu and Y)

    Energy Technology Data Exchange (ETDEWEB)

    Sarrao, J L [Los Alamos National Laboratory; Thompson, Joe D [Los Alamos National Laboratory; Tobash, P H [UNIV. OF DE; Bobev, S [UNIV. OF DE

    2009-01-01

    A series of magnesium-substituted rare-earth metal germanides with a general formula RE{sub 5-x}Mg{sub x}Ge{sub 4} (x {approx} 1.0-2.3; RE =Gd-Tm, Lu, Y) have been synthesized by high-temperature reactions and structurally characterized by single-crystal X-ray diffraction. These compounds crystallize with the common Gd{sub 5}Si{sub 4} type in the orthorhombic space group Pnma (No. 62; Z =4; Pearson's code oP36) and do not appear to undergo temperature-induced crystallographic phase transitions down to 120 K. Replacing rare-earth metal atoms with Mg, up to nearly 45 % at., reduces the valence electron count and is clearly expressed in the subtle changes of the Ge-Ge and metal-metal bonding. Magnetization measurements as a function of the temperature and the applied field reveal complex magnetic structures at cryogenic temperatures, and Curie-Weiss paramagnetic behavior at higher temperatures. The observed local moment magnetism is consistent with RE+ ground states in all cases. In the magnetically ordered phases, the magnetization cannot reach saturation in fields up to 50 kOe. The structural trends across the series and the variations of hte magnetic properties as a function of the Mg content are also discussed. KEYWORDS: Rare-earth intermetallics, germanides, crystal structure,Gd{sub 5}Si{sub 4} type.