WorldWideScience

Sample records for alkali feldspars ii

  1. Experimental study on crystallization kinetics of alkali feldspar under high T-P conditions

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In the granite-NaF-H2O system, there exists a nucleation lag in the course of alkali feldspar crystallization indicated by experiments on crystallization kinetics. The nucleation lag time is about 18 h at 700℃ and about 6 h at 650℃. Meanwhile, both nucleation rate and crystal-growth rate of alkali feldspar are not constant during the crystallization process, but vary with crystal- lization time. Here we suggest that the lag time should be taken into account in the calculation formula of nucleation rate and crystal-growth rate to obtain more reliable parameters.

  2. Thermodynamic assessment of hydrothermal alkali feldspar-mica-aluminosilicate equilibria

    Science.gov (United States)

    Sverjensky, Dimitri A.; Hemley, J. J.; D'angelo, W. M.

    1991-04-01

    The thermodynamic properties of minerals retrieved from consideration of solid-solid and dehydration equilibria with calorimetric reference values, and those of aqueous species derived from studies of electrolytes, are not consistent with experimentally measured high-temperature solubilities in the systems K 2O- and Na 2O-Al 2O 3-SiO 2-H 2O-HCl (e.g., K-fs - Ms - Qtz - K + - H +). This introduces major inaccuracies into the computation of ionic activity ratios and the acidities of diagenetic, metamorphic, and magmatic hydrothermal fluids buffered by alkali silicate-bearing assemblages. We report a thermodynamic analysis of revised solubility equilibria in these systems that integrates the thermodynamic properties of minerals obtained from phase equilibria studies ( BERMAN, 1988) with the properties of aqueous species calculated from a calibrated equation of state ( SHOCK and HELGESON, 1988). This was achieved in two separate steps. First, new values of the free energies and enthalpies of formation at 25°C and 1 bar for the alkali silicates muscovite and albite were retrieved from the experimental solubility equilibria at 300°C and P sat. Because the latter have stoichiometric reaction coefficients different from those for solid-solid and dehydration equilibria, our procedure preserves exactly the relative thermodynamic properties of the alkali-bearing silicates ( BERMAN, 1988). Only simple arithmetic adjustments of -1,600 and -1,626 ( ±500) cal/mol to all the K- and Na-bearing silicates, respectively, in BERMAN (1988) are required. In all cases, the revised values are within ±0.2% of calorimetric values. Similar adjustments were derived for the properties of minerals from HELGESON et al. (1978). Second, new values of the dissociation constant of HCl were retrieved from the solubility equilibria at temperatures and pressures from 300-600°C and 0.5-2.0 kbars using a simple model for aqueous speciation. The results agree well with the conductance

  3. 29Si and 27AI MAS NMR Study of Alkali Feldspars

    Institute of Scientific and Technical Information of China (English)

    周玲棣; 郭九皋; 袁汉珍; 李丽云

    1994-01-01

    12 natural alkali feldspars have been studied by(29)~Si and(27)~Al MAS NMR as well as XRD,IR,EPMA and chemical analysis.Three kinds of(29)~Si NMR spectra,i.e.the spectra of microcline,perthiteand perthite with minor plagioclase,have been obtained.There are two types of(27)~Al NMR spectra.The(27)~Alspectrum of microcline is the same as that of perthite,but is different from the spectrum for perthite contain-ing plagioclase.Through this study,we found that the results of NMR and IR are inconsistent with that ofXRD,which shows that the transition of alkali feldspar from monoclinic to triclinic system might be a rathercomplicated process.

  4. Alkali feldspar syenites with shoshonitic affinities from Chhotaudepur area:Implication for mantle metasomatism in the Deccan large igneous province

    Institute of Scientific and Technical Information of China (English)

    K.R. Hari; N.V. Chalapathi Rao; Vikas Swarnkar; Guiting Hou

    2014-01-01

    Two petrologically distinct alkali feldspar syenite bodies (AFS-1 and AFS-2) from Chhotaudepur area, Deccan Large Igneous Province are reported in the present work. AFS-1 is characterized by hypidio-morphic texture and consists of feldspar (Or55Ab43 to Or25Ab71), ferro-pargasite/ferro-pargasite horn-blende, hastingsite, pyroxene (Wo47, En5, Fs46), magnetite and biotite. AFS-2 exhibits panidiomorphic texture with euhedral pyroxene (Wo47-50, En22-39, Fs12e31) set in a groundmass matrix of alkali feldspar (Or99Ab0.77 to Or1.33Ab98), titanite and magnetite. In comparison to AFS-1, higher elemental concentra-tions of Ba, Sr and PREE are observed in AFS-2. The average peralkaline index of the alkali feldspar syenites is w1 indicating their alkaline nature. Variation discrimination diagrams involving major and trace elements and their ratios demonstrate that these alkali feldspar syenites have a shoshonite affinity but emplaced in a within-plate and rifting environment. No evidence of crustal contamination is perceptible in the multi-element primitive mantle normalized diagram as well as in terms of trace elemental ratios. The enrichment of incompatible elements in the alkali feldspar syenites suggests the involvement of mantle metasomatism in their genesis.

  5. Potassium self-diffusion in a K-rich single-crystal alkali feldspar

    Science.gov (United States)

    Hergemöller, Fabian; Wegner, Matthias; Deicher, Manfred; Wolf, Herbert; Brenner, Florian; Hutter, Herbert; Abart, Rainer; Stolwijk, Nicolaas A.

    2016-12-01

    The paper reports potassium diffusion measurements performed on gem-quality single-crystal alkali feldspar in the temperature range from 1169 to 1021 K. Natural sanidine from Volkesfeld, Germany was implanted with ^{43}K at the ISOLDE/CERN radioactive ion-beam facility normal to the ( 001) crystallographic plane. Diffusion coefficients are well described by the Arrhenius equation with an activation energy of 2.4 eV and a pre-exponential factor of 5 × 10^{-6} m^2/s, which is more than three orders of magnitude lower than the ^{22}Na diffusivity in the same feldspar and the same crystallographic direction. State-of-the-art considerations including ionic conductivity data on the same crystal and Monte Carlo simulations of diffusion in random binary alloy structures point to a correlated motion of K and Na through the interstitialcy mechanism.

  6. Potassium self-diffusion in a K-rich single-crystal alkali feldspar

    Science.gov (United States)

    Hergemöller, Fabian; Wegner, Matthias; Deicher, Manfred; Wolf, Herbert; Brenner, Florian; Hutter, Herbert; Abart, Rainer; Stolwijk, Nicolaas A.

    2017-05-01

    The paper reports potassium diffusion measurements performed on gem-quality single-crystal alkali feldspar in the temperature range from 1169 to 1021 K. Natural sanidine from Volkesfeld, Germany was implanted with {}^{43}{\\hbox {K}} at the ISOLDE/CERN radioactive ion-beam facility normal to the ( 001) crystallographic plane. Diffusion coefficients are well described by the Arrhenius equation with an activation energy of 2.4 eV and a pre-exponential factor of 5 × 10^{-6} {\\hbox {m}}^2/{\\hbox {s}}, which is more than three orders of magnitude lower than the {}^{22}{\\hbox {Na}} diffusivity in the same feldspar and the same crystallographic direction. State-of-the-art considerations including ionic conductivity data on the same crystal and Monte Carlo simulations of diffusion in random binary alloy structures point to a correlated motion of K and Na through the interstitialcy mechanism.

  7. The nature of potassium feldspar, exsolution microtextures and development of dislocations as a function of composition in perthitic alkali feldspars

    Science.gov (United States)

    Brown, William L.; Parsons, Ian

    1984-12-01

    Transmission electron microscope data on the morphology of exsolution lamellae, the nature of the potassium feldspar and the development of dislocations at lamellar interfaces in coherent cryptoperthites and fine microperthites are reviewed. Dislocations have been reported previously in only two crystals, and periodic dislocations noted in only one, an Or-rich microperthite. Periodic dislocations (spacing 100 150 nm) are here described from a ternary mesoperthite (Or26 Ab52 An22). Small crystallites (microcline formation, and tweed orthoclase develops. Interfaces do not migrate, and dislocations again develop. Fields in which different potassium feldspar polymorphs occur and in which the different exsolution textures are developed are summarized on a ternary diagram.

  8. Solid-state nuclear magnetic resonance and infrared spectroscopy of alkali feldspars

    Institute of Scientific and Technical Information of China (English)

    周玲棣; 郭九皋; 杨年华; 李丽云

    1997-01-01

    29Si, 27Al MAS NMR and IR spectra of monophase K-feldspars (sanidine, orthoclase and micro-cline) and Na-feldspars (monalbite, anorthoclase and low albite) in different structural states have been studied. The NMR and IR spectra of K-feldspars and Na-feldspars vary regularly along with their degrees of Si/Al ordering evolution. Si in orthoclase occupies T2m, T2o and T1m, and the high-temperature Na-feldspar (monalbite and anorthoclase) coincides in 29Si, 27Al NMR and IR spectra. Moreover, all the high-temperature Na-feldspars and sanidine have the same 27Al NMR and IR spectra.

  9. Biochemical evolution II: origin of life in tubular microstructures on weathered feldspar surfaces.

    Science.gov (United States)

    Parsons, I; Lee, M R; Smith, J V

    1998-12-22

    Mineral surfaces were important during the emergence of life on Earth because the assembly of the necessary complex biomolecules by random collisions in dilute aqueous solutions is implausible. Most silicate mineral surfaces are hydrophilic and organophobic and unsuitable for catalytic reactions, but some silica-rich surfaces of partly dealuminated feldspars and zeolites are organophilic and potentially catalytic. Weathered alkali feldspar crystals from granitic rocks at Shap, north west England, contain abundant tubular etch pits, typically 0.4-0.6 microm wide, forming an orthogonal honeycomb network in a surface zone 50 microm thick, with 2-3 x 10(6) intersections per mm2 of crystal surface. Surviving metamorphic rocks demonstrate that granites and acidic surface water were present on the Earth's surface by approximately 3.8 Ga. By analogy with Shap granite, honeycombed feldspar has considerable potential as a natural catalytic surface for the start of biochemical evolution. Biomolecules should have become available by catalysis of amino acids, etc. The honeycomb would have provided access to various mineral inclusions in the feldspar, particularly apatite and oxides, which contain phosphorus and transition metals necessary for energetic life. The organized environment would have protected complex molecules from dispersion into dilute solutions, from hydrolysis, and from UV radiation. Sub-micrometer tubes in the honeycomb might have acted as rudimentary cell walls for proto-organisms, which ultimately evolved a lipid lid giving further shelter from the hostile outside environment. A lid would finally have become a complete cell wall permitting detachment and flotation in primordial "soup." Etch features on weathered alkali feldspar from Shap match the shape of overlying soil bacteria.

  10. Trace-element partitioning at conditions far from equilibrium: Ba and Cs distributions between alkali feldspar and undercooled hydrous granitic liquid at 200 MPa

    Science.gov (United States)

    Morgan, George; London, David

    2002-12-01

    This study examines the effects of increasing supersaturation, attained by single-step liquidus undercooling (ΔT), on the partitioning of barium and cesium between potassic alkali feldspar (Afs) and hydrous granitic liquid at 200 MPa. The investigation is motivated by trace-element distribution patterns in granitic pegmatites which cannot be simulated by fractionation models using "equilibrium" partition coefficients, and thus its purpose is to assess if, how, and why partition coefficients for compatible and incompatible trace elements may vary when crystal growth commences far from the crystal-melt equilibrium boundary. Barium expands the liquidus stability field of potassic feldspar to higher temperatures, such that liquidi for the Ba-rich ( 0.5 wt% BaO) compositions used are 100 °C higher than for Ba-absent analogues. At low degrees of undercooling (ΔT 50 °C), values of DBaAfs/m. ( 10-20) fall within the range of previous investigations, as do values of DCsAfs/m. (=100 °C) are heterogeneous, such that DBaAfs/m. versus K/K+Na varies linearly between the average value at 850 °C and the equilibrium value appropriate to the temperature of growth. Hence, high supersaturation accompanying undercooling produces feldspar compositions by isothermal growth which record a vestige of the liquid line of descent (i.e., an ontogeny within zoned crystals which approximately tracks the feldspar liquidus from high temperature to the final low temperature of actual crystal growth). Such zoning patterns may mimic normal patterns produced by fractionation with decreasing temperature under near-equilibrium (near-liquidus) conditions. Increasing fluorine contents tend to exacerbate the effects of undercooling by inhibiting feldspar nucleation, causing both K/K+Na ratios and compatible trace-element partitioning behavior in feldspar to deviate from equilibrium values. This effect continues until nucleation lag is overcome, whereupon a period of rapid growth from supersaturated

  11. Origin of hydrous alkali feldspar-silica intergrowth in spherulites from intra-plate A2-type rhyolites at the Jabal Shama, Saudi Arabia

    Science.gov (United States)

    Surour, Adel A.; El-Nisr, Said A.; Bakhsh, Rami A.

    2016-03-01

    Miocene rhyolites (19.2 ± 0.9 Ma) at the Jabal Shama in western Saudi Arabia represent an example of rift-related silicic volcanism that took place during the formation of the Red Sea. They mostly consist of tuffaceous varieties with distinct flow banding, and pea-sized spherulites, obsidian and perlitized rhyolite tuffs. Although they have the geochemical signature of A2-type rhyolites, these silicic rocks are not typically alkaline but alkali-calcic to calc-alkaline. They developed in a within-plate regime and possibly derived from a recycled mafic subducted slab in depleted sub-continental mantle beneath the western Arabian plate. The Jabal Shama rhyolites are younger in age than their Miocene counterparts in Yemen and Ethiopia. The Jabal Shama spherulites consist of hydrous alkali feldspar-silica radial intergrowths with an occasional brown glass nucleus. Carbonate- and glass-free spherulites give up to 4.45 wt% L.O.I. The hydrous nature of these silicates and the absence of magnetite in the spherulites is a strong indication of oxidizing conditions. The spherulites contain hydrous feldspars with up to ∼6 wt% H2O, and they develop by diffusion and devitrification of glass in the rhyolite tuff at ∼800 °C. Owing to higher undercooling due to supersaturation, the radial hydrous phases within spherulites might grow faster and led to coagulation. The polygonal contacts between spherulites and the ∼120° dihedral angle suggest solid-state modification and recrystallization as the process of devitrification proceeds as low as ∼300 °C. The sum of FeO + MgO is positively correlated with total alkalies along with magnetite oxidation in the matrix to Fe-oxyhydroxides, and to the incorporation of OH- into silicates within the spehrulites themselves. Structural H2O in glass of the Jabal Shama perlite (obsidian) is considerable (∼9-12 wt%) with 3.72-5.6 wt% L.O.I. of the whole-rock. The presence of deleterious silica impurities would lower the ore grade due to

  12. A comparative study for the sorption of Cd(II) by K-feldspar and sepiolite as soil components, and the recovery of Cd(II) using rhamnolipid biosurfactant.

    Science.gov (United States)

    Aşçi, Y; Nurbaş, M; Açikel, Y Sağ

    2008-08-01

    This study investigated the sorption characteristics and recovery of selected heavy metal Cd(II) from K-feldspar and sepiolite, representative soil components, using rhamnolipid biosurfactant. Although the proposed technique was classified as a soil bioremediation process, it can also be applied to treatment of waste waters containing Cd(II) ions with minor modifications. The effect of initial Cd(II) concentration on sorption capacity was characterized by determining the sorption isotherms. Of the four models examined, the Freundlich model showed the best fit for the sorption of Cd(II) on K-feldspar, whereas the Langmuir-model was used successfully to characterize the sorption of Cd(II) on sepiolite. Although a high Cd(II) uptake of 7.49 mmol/kg by K-feldspar was obtained, sepiolite was a superior Cd(II) accumulater, with a maximum Cd(II) uptake of 24.66 mmol Cd(II)/kg. The presence of Cd(II) in the sepiolite or K-feldspar prior to addition of the rhamnolipid generally resulted in less rhamnolipid sorption to sepiolite or K-feldspar. The maximum Cd(II) desorption efficiency by rhamnolipid from K-feldspar was substantially higher than that of sepiolite and determined to be 96% of the sorbed Cd(II), whereas only 10.1% of the sorbed Cd(II) from sepiolite was recovered by rhamnolipid solution.

  13. Electrons in feldspar II: A consideration of the influence of conduction band-tail states on luminescence processes

    DEFF Research Database (Denmark)

    Poolton, H.R.J.; Ozanyan, K.B.; Wallinga, J.

    2002-01-01

    Most natural feldspars contain many charged impurities, and display a range of bond angles, distributed about the ideal. These effects can lead to complications in the structure of the conduction band, giving rise to a tail of energy states (below the high-mobility conduction band) through which ...

  14. Feldspar, Infrared Stimulated Luminescence

    DEFF Research Database (Denmark)

    Jain, Mayank

    2014-01-01

    This entry primarily concerns the characteristics and the origins of infrared-stimulated luminescence in feldspars.......This entry primarily concerns the characteristics and the origins of infrared-stimulated luminescence in feldspars....

  15. Effect of Alkali Treatment of Wheat Straw on Adsorption of Cu(II under Acidic Condition

    Directory of Open Access Journals (Sweden)

    Yiping Guo

    2016-01-01

    Full Text Available The convenient and feasible pretreatment method of alkali treatment is very common in the degradation process of wheat straw. However, its utilization in the pretreatment of wheat straw as alternative adsorbents for aqueous heavy metals remediation is rarely reported. The present study investigated the removal efficiency of Cu(II ions using wheat straw with alkali pretreatment. The condition of alkali treatment on wheat straw was optimized with the adsorption capacity of Cu(II as indicator using single-factor experiments. The influences of wheat straw dosages, pH values, contact time, and temperatures on adsorption performance for both untreated wheat straw (UWS and alkali-treated wheat straw (AWS were investigated. Results showed that the relatively large removal rate of Cu(II could be obtained, and chemical behavior occurred during the adsorption process. Characteristic analysis found that the major function of alkali treatment to wheat straw was to introduce the hydroxy group, which resulted in the increase of -C-O- group. Although the adsorption capacity is not as high as the one of ligands supported adsorbents, the method is easy to operate and has a wide range of application; at the same time, it could realize both purposes of treating heavy metal pollution and solid wastes.

  16. Alkali/Surfactant/Polymer Flooding in the Daqing Oilfield Class II Reservoirs Using Associating Polymer

    Directory of Open Access Journals (Sweden)

    Ru-Sen Feng

    2013-01-01

    Full Text Available Hydrophobically modified associating polyacrylamide (HAPAM has good compatibility with the Daqing heavy alkylbenzene sulfonate surfactant. The HAPAM alkali/surfactant/polymer (ASP system can generate ultralow interfacial tension in a wide range of alkali/surfactant concentrations and maintain stable viscosity and interfacial tension for 120 days. The HAPAM ASP system has good injectivity for the Daqing class II reservoirs (100–300 × 10−3 μm2 and can improve oil recovery by more than 25% on top of water flooding. In the presence of both the alkali and the surfactant, the surfactant interacts with the associating groups of the polymer to form more micelles, which can significantly enhance the viscosity of the ASP system. Compared with using HPAM (Mw = 2.5 MDa, using HAPAM can reduce the polymer use by more than 40%.

  17. Residence times of alkali feldspar phenocrysts from magma feeding the Agnano-Monte Spina Eruption (4.7 ka), Campi Flegrei caldera (Napoli, southern Italy) based on Ba-zonation modelling

    Science.gov (United States)

    Iovine, Raffaella Silvia; Wörner, Gerhard; Carmine Mazzeo, Fabio; Arienzo, Ilenia; Fedele, Lorenzo; Civetta, Lucia; D'Antonio, Massimo; Orsi, Giovanni

    2016-04-01

    Timescales governing the development of crustal magma reservoirs are a key for understanding magmatic processes such as ascent, storage and mixing event. An estimate of these timescales can provide important constraints for volcanic hazard assessment of active volcanoes. We studied the Agnano-Monte Spina eruption (A-MS; 4.7 ka; VEI = 4; 0.85 km3 D.R.E. of magma erupted) of the Campi Flegrei caldera, one of the most dangerous volcanic areas on Earth. The A-MS eruption has been fed by magmas varying from more to less evolved trachyte whose variable 87Sr/86Sr and trace elements features suggest magma mixing between two end-members. Ba zonation profiles of alkali feldspar phenocrysts have been determined through combined energy-dispersive and wavelength-dispersive electron microprobe analyses (EDS-WDS-EMPA). We focused on distinct compositional breaks near the rim of the crystals that likely represent the last mixing event prior to eruption. We always chose the steepest gradients close to the crystal rims, taking into account that any effects related to cutting angles or crystal orientation should give longer apparent diffusion times. Two different approaches were undertaken: (1) a quantitative Ba compositional profiles were measured by point analyses along a short transect crossing growth discontinuities and (2) grey-scale profiles were taken parallel to the acquired point profiles. Assuming that Ba dominates the backscattered electron intensities in sanidines, greyscale gradients can be used as a diffusive tracer. BSE images were processed using the ImageJ® software, in order to extract a numerical greyscale profile. In both cases, each profile was interpolated through a non-linear Boltzmann fit curve with the Mathematica® software. A few traverses done at angles smaller than 90° to the compositional boundary interface were corrected by multiplying the distance values by the sinus of the traverse angle relative to the vertical on the interface. Our preliminary

  18. Principles of Thermal Expansion in Feldspars

    Science.gov (United States)

    Hovis, Guy; Medford, Aaron; Conlon, Maricate; Tether, Allison; Romanoski, Anthony

    2010-05-01

    Following the recent thermal expansion work of Hovis et al. (1) on AlSi3 feldspars, we have investigated the thermal expansion of plagioclase, Ba-K, and Ca-K feldspar crystalline solutions. X-ray powder diffraction data were collected between room temperature and 925 °C on six natural plagioclase specimens ranging in composition from anorthite to oligoclase, the K-exchanged equivalents of these plagioclase specimens, and five synthetic Ba-K feldspars with compositions ranging from 25 to 99 mol % BaAl2Si2O8. The resulting thermal expansion coefficients (α) for volume have been combined with earlier results for end-member Na- and K-feldspars (2,3). Unlike AlSi3 feldspars, Al2Si2 feldspars, including anorthite and celsian from the present study plus Sr- and Pb-feldspar from other workers (4,5), show essentially constant and very limited thermal expansion, regardless of divalent cation size. In the context of structures where the Lowenstein rule (6) requires Al and Si to alternate among tetrahedra, the proximity of bridging Al-O-Si oxygen ions to divalent neighbors (ranging from 0 to 2) produces short Ca-O (or Ba-O) bonds (7,8) that apparently are the result of local charge-balance requirements (9). Gibbs et al. (10) suggest that short bonds such as these have a partially covalent character. This in turn stiffens the structure. Thus, for feldspar series with coupled substitution the change away from a purely divalent M-site occupant gives the substituting (less strongly bonded) monovalent cations increasingly greater influence on thermal expansion. Overall, then, thermal expansion in the feldspar system is well represented on a plot of α against room-temperature volume, where one sees a quadrilateral bounded by data for (A) AlSi3 feldspars whose expansion behavior is controlled largely by the size of the monovalent alkali-site occupant, (B) Al2Si2 feldspars whose expansion is uniformly limited by partially-covalent bonds between divalent M-site occupants and

  19. Thermal quenching of luminescence processes in feldspars

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Bøtter-Jensen, L.; Duller, G.A.T.

    1995-01-01

    The technique of optically stimulated luminescence has important uses in the dose evaluation of irradiated feldspars. The luminescence process involves the eviction of electrons from donor traps, charge transfer through the conduction band, and recombination at acceptor sites; each...... of these processes is, in general, thermally dependent, and leads either to enhancement or quenching of the luminescence with increasing temperature. Previous studies have measured the combined thermal activation characteristics of all three processes, and show a strong dependence on stimulation energy....... In this article, an initial attempt is made to isolate only the recombination part of the luminescence cycle, and determine its thermal characteristics separately. A Variety of luminescence transitions are examined in a range of both alkali and plagioclase feldspars; three distinct emission types are identified...

  20. Can cathodoluminescence of feldspar be used as provenance indicator?

    Science.gov (United States)

    Scholonek, Christiane; Augustsson, Carita

    2016-05-01

    We have studied feldspar from crystalline rocks for its textural and spectral cathodoluminescence (CL) characteristics with the aim to reveal their provenance potential. We analyzed ca. 60 rock samples of plutonic, volcanic, metamorphic, and pegmatitic origin from different continents and of 16 Ma to 2 Ga age for their feldspar CL textures and ca. 1200 feldspar crystals from these rocks for their CL color spectra. Among the analyzed rocks, igneous feldspar is most commonly zoned, whereby oscillatory zoning can be confirmed to be typical for volcanic plagioclase. The volcanic plagioclase also less commonly contains twin lamellae that are visible in CL light than crystals from other rock types. Alkali feldspar, particularly from igneous and pegmatitic rocks, was noted to be most affected by alteration features, visible as dark spots, lines and irregular areas. The size of all textural features of up to ca. 150 μm, in combination with possible alteration in both the source area and the sedimentary system, makes the CL textures of feldspar possible to use for qualitative provenance research only. We observed alkali feldspar mostly to luminesce in a bluish color and sometimes in red, and plagioclase in green to yellow. The corresponding CL spectra are dominated by three apparent intensity peaks at 440-520 nm (mainly blue), 540-620 nm (mainly green) and 680-740 nm (red to infrared). A dominance of the peak in the green wavelength interval over the blue one for plagioclase makes CL particularly useful for the differentiation of plagioclase from alkali feldspar. An apparent peak position in red to infrared at < 710 nm for plagioclase mainly is present in mafic rocks. Present-day coastal sand from Peru containing feldspar with the red to infrared peak position mainly exceeding 725 nm for northern Peruvian sand and a larger variety for sand from southern Peru illustrates a discriminative effect of different source areas. We conclude that the provenance application

  1. Adsorption behavior of Cu(II) onto titanate nanofibers prepared by alkali treatment.

    Science.gov (United States)

    Li, Nian; Zhang, Lide; Chen, Yongzhou; Tian, Yue; Wang, Huimin

    2011-05-15

    Novel low-cost adsorbents of titanate nanofibers with formula Na(x)H(2-x)Ti(3)O(7) · nH(2)O have been prepared by alkali treatment for Cu(II) removal from aqueous solutions. The nanofibers have structures in which three edge-shared TiO(6) octahedras join at the corners to form stepped, zigzag Ti(3)O(7)(2-) layers. The sodium cations located between the layers are exchangeable. The results of batch adsorption experiments suggest that the nanofibers with high sodium content can be effective adsorbents for Cu(II) removal. Effects of several important factors such as Na amount in adsorbents, pH, temperature, contact time and initial concentration are systematically studied. Results show that the adsorption is highly pH-dependent and the removal is almost complete (99.8%) for initial concentration under 100mg/l at pH 4. Equilibrium adsorption follows Langmuir isotherms well and the maximum Cu(II) uptake calculated is 167.224 mg/g. The adsorption kinetics can be explained by pseudo-second-order model well and the time needed for equilibrium is 180 min. Thermodynamic study indicates that the adsorption is spontaneous and endothermic. Desorption of Cu(II) from adsorbents using EDTA-2Na solutions exhibits a high efficiency and the adsorbents can be used repeatedly. These results demonstrate that the titanate nanofibers are readily prepared, enabling promising applications for the removal of Cu(II) from aqueous solutions.

  2. Adsorption behavior of Cu(II) onto titanate nanofibers prepared by alkali treatment

    Energy Technology Data Exchange (ETDEWEB)

    Li, Nian [Key Laboratory of Materials Physics, Anhui Key laboratory of Nanomaterials and Nanostructure, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China); Zhang, Lide, E-mail: ldzhang@issp.ac.cn [Key Laboratory of Materials Physics, Anhui Key laboratory of Nanomaterials and Nanostructure, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China); Chen, Yongzhou; Tian, Yue; Wang, Huimin [Key Laboratory of Materials Physics, Anhui Key laboratory of Nanomaterials and Nanostructure, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China)

    2011-05-15

    Novel low-cost adsorbents of titanate nanofibers with formula Na{sub x}H{sub 2-x}Ti{sub 3}O{sub 7}.nH{sub 2}O have been prepared by alkali treatment for Cu(II) removal from aqueous solutions. The nanofibers have structures in which three edge-shared TiO{sub 6} octahedras join at the corners to form stepped, zigzag Ti{sub 3}O{sub 7}{sup 2-} layers. The sodium cations located between the layers are exchangeable. The results of batch adsorption experiments suggest that the nanofibers with high sodium content can be effective adsorbents for Cu(II) removal. Effects of several important factors such as Na amount in adsorbents, pH, temperature, contact time and initial concentration are systematically studied. Results show that the adsorption is highly pH-dependent and the removal is almost complete (99.8%) for initial concentration under 100 mg/l at pH 4. Equilibrium adsorption follows Langmuir isotherms well and the maximum Cu(II) uptake calculated is 167.224 mg/g. The adsorption kinetics can be explained by pseudo-second-order model well and the time needed for equilibrium is 180 min. Thermodynamic study indicates that the adsorption is spontaneous and endothermic. Desorption of Cu(II) from adsorbents using EDTA-2Na solutions exhibits a high efficiency and the adsorbents can be used repeatedly. These results demonstrate that the titanate nanofibers are readily prepared, enabling promising applications for the removal of Cu(II) from aqueous solutions.

  3. Radiation dosimetry by potassium feldspar

    Indian Academy of Sciences (India)

    Arun Pandya; S G Vaijapurkar; P K Bhatnagar

    2000-04-01

    The thermoluminescence (TL) properties of raw and annealed feldspar have been studied for their use in gamma dosimetry. The raw gamma exposed feldspar shows glow peaks at 120°C and 319°C. Gamma dose beyond 500 cGy can be measured without any significant fading even after 40 days of termination of exposure. The annealed feldspar shows a glow peak at 120°C after gamma exposure. This peak can be used to measure gamma doses beyond 25 cGy when the TL is measured after 24 h from termination of exposure.

  4. Observation of free electron cyclotron resonance in NaAlSi3O8 feldspar: Direct determination of the effective electron mass

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Nicholis, J.E.; Bøtter-Jensen, L.;

    2001-01-01

    We report the first observation of cyclotron resonances in alkali feldspars, using highly sensitive optical detection methods. In Na-feldspar (NaAlSi3O8). a near isotropic effective electron mass value of m(c)(*) = 0.79m, has been determined. The significance of this measurement in terms of the o......We report the first observation of cyclotron resonances in alkali feldspars, using highly sensitive optical detection methods. In Na-feldspar (NaAlSi3O8). a near isotropic effective electron mass value of m(c)(*) = 0.79m, has been determined. The significance of this measurement in terms...

  5. A curious interplay in the films of N-heterocyclic carbene PtII complexes upon deposition of alkali metals

    Science.gov (United States)

    Makarova, Anna A.; Grachova, Elena V.; Niedzialek, Dorota; Solomatina, Anastasia I.; Sonntag, Simon; Fedorov, Alexander V.; Vilkov, Oleg Yu.; Neudachina, Vera S.; Laubschat, Clemens; Tunik, Sergey P.; Vyalikh, Denis V.

    2016-05-01

    The recently synthesized series of PtII complexes containing cyclometallating (phenylpyridine or benzoquinoline) and N-heterocyclic carbene ligands possess intriguing structures, topologies, and light emitting properties. Here, we report curious physicochemical interactions between in situ PVD-grown films of a typical representative of the aforementioned PtII complex compounds and Li, Na, K and Cs atoms. Based on a combination of detailed core-level photoelectron spectroscopy and quantum-chemical calculations at the density functional theory level, we found that the deposition of alkali atoms onto the molecular film leads to unusual redistribution of electron density: essential modification of nitrogen sites, reduction of the coordination PtII centre to Pt0 and decrease of electron density on the bromine atoms. A possible explanation for this is formation of a supramolecular system “Pt complex-alkali metal ion” the latter is supported by restoration of the system to the initial state upon subsequent oxygen treatment. The discovered properties highlight a considerable potential of the PtII complexes for a variety of biomedical, sensing, chemical, and electronic applications.

  6. A curious interplay in the films of N-heterocyclic carbene Pt(II) complexes upon deposition of alkali metals.

    Science.gov (United States)

    Makarova, Anna A; Grachova, Elena V; Niedzialek, Dorota; Solomatina, Anastasia I; Sonntag, Simon; Fedorov, Alexander V; Vilkov, Oleg Yu; Neudachina, Vera S; Laubschat, Clemens; Tunik, Sergey P; Vyalikh, Denis V

    2016-05-06

    The recently synthesized series of Pt(II) complexes containing cyclometallating (phenylpyridine or benzoquinoline) and N-heterocyclic carbene ligands possess intriguing structures, topologies, and light emitting properties. Here, we report curious physicochemical interactions between in situ PVD-grown films of a typical representative of the aforementioned Pt(II) complex compounds and Li, Na, K and Cs atoms. Based on a combination of detailed core-level photoelectron spectroscopy and quantum-chemical calculations at the density functional theory level, we found that the deposition of alkali atoms onto the molecular film leads to unusual redistribution of electron density: essential modification of nitrogen sites, reduction of the coordination Pt(II) centre to Pt(0) and decrease of electron density on the bromine atoms. A possible explanation for this is formation of a supramolecular system "Pt complex-alkali metal ion"; the latter is supported by restoration of the system to the initial state upon subsequent oxygen treatment. The discovered properties highlight a considerable potential of the Pt(II) complexes for a variety of biomedical, sensing, chemical, and electronic applications.

  7. The Thermal Expansion Of Feldspars

    Science.gov (United States)

    Hovis, G. L.; Medford, A.; Conlon, M.

    2009-12-01

    Hovis and others (1) investigated the thermal expansion of natural and synthetic AlSi3 feldspars and demonstrated that the coefficient of thermal expansion (α) decreases significantly, and linearly, with increasing room-temperature volume (VRT). In all such feldspars, therefore, chemical expansion limits thermal expansion. The scope of this work now has been broadened to include plagioclase and Ba-K feldspar crystalline solutions. X-ray powder diffraction data have been collected between room temperature and 925 °C on six plagioclase specimens ranging in composition from anorthite to oligoclase. When combined with thermal expansion data for albite (2,3,4) a steep linear trend of α as a function of VRT emerges, reflecting how small changes in composition dramatically affect expansion behavior. The thermal expansion data for five synthetic Ba-K feldspars ranging in composition from 20 to 100 mole percent celsian, combined with data for pure K-feldspar (3,4), show α-VRT relationships similar in nature to the plagioclase series, but with a slope and intercept different from the latter. Taken as a group all Al2Si2 feldspars, including anorthite and celsian from the present study along with Sr- (5) and Pb-feldspar (6) from other workers, show very limited thermal expansion that, unlike AlSi3 feldspars, has little dependence on the divalent-ion (or M-) site occupant. This apparently is due to the necessitated alternation of Al and Si in the tetrahedral sites of these minerals (7), which in turn locks the tetrahedral framework and makes the M-site occupant nearly irrelevant to expansion behavior. Indeed, in feldspar series with coupled chemical substitution it is the change away from a 1:1 Al:Si ratio that gives feldspars greater freedom to expand. Overall, the relationships among α, chemical composition, and room-temperature volume provide useful predictive tools for estimating feldspar thermal expansion and give insight into the controls of expansion behavior in

  8. U-Pb (SHRIMP-II) isotope dating of zircons from alkali rocks of Vitim province, West Transbaikalia

    Science.gov (United States)

    Doroshkevich, A. G.; Ripp, G. S.; Sergeev, S. A.

    2012-03-01

    A U-Pb (SHRIMP-II) geochronological study of rocks from the Sayzhenski, Snezhny and Nizhne-Burulzayski massifs, incorporated into the Vitim alkali province (Sayzhenski Complex) has been made. The acquired data indicate that the rocks formed in the interval of 520-486 Ma. The proximity of their age to accretionary-collision processes in the Central Asian fold belt, accompanied by intràplate magmatism, has been noted. Two independent stages in the evolution of Vitim Province magmatism are suggested: Early Paleozoic (520-485 Ma) and Late Paleozoic (350-290 Ma).

  9. Plagioclase-mantled K-feldspar in the Carboniferous porphyritic microgranite of Altenberg-Frauenstein, Eastern Erzgebirge/Krusné Hory

    Directory of Open Access Journals (Sweden)

    Axel Müller

    2002-01-01

    Full Text Available The Upper Carboniferous porphyritic microgranite of Altenberg-Frauenstein, formerly known as Granitporphyr (Dalmer 1896 and here abbreviated as GP, forms a 36 km long and up to 18 km wide complex of ring dykes related to the Teplice-Altenberg caldera in the German–Czech border region of the Eastern Erzgebirge/Krusné Hory. The microgranites are characterized by the occurrence of plagioclase-mantled K-feldspar phenocrysts. The microgranite varieties representtwo main stages of intrusion evolved from acid (GP I to intermediaterocks (GP II within the intrusion. The most acid rock (GP Icum occurs as enclaves in GP I and GP II and is interpreted as a cumulate of K-feldspar and quartz phenocrysts. The porphyritic microgranites show field, textural and geochemical evidence suggesting that some of them have formed as a result of interaction between felsic and mafic magmas. Mixing features are abundant in the porphyriticquartz-feldspar-hornblende microgranite (GP II interpreted as a hybrid rock. They are less discrete in the early phase (GP I and not obvious in the acid enclaves (GP Icum. This trend seems to reflect a continuous deflation of the magma chamber from the top to the bottom. According to the definition of rapakivi granites after Haapala and Rämö (1992, the porphyritic microgranite of Altenberg-Frauenstein may be considered as rapakivi granite although ovoid alkali feldspar megacrysts typical of classical rapakivi granites are not recorded.However, due to its Carboniferous age and being the only known granitewith rapakivi texture in the German–Czech part of the Variscan belt, the microgranite of Altenberg-Frauenstein is exceptional.

  10. Feldspar dissolution rates in the Topopah Spring Tuff, Yucca Mountain, Nevada

    Science.gov (United States)

    Bryan, C.R.; Helean, K.B.; Marshall, B.D.; Brady, P.V.

    2009-01-01

    Two different field-based methods are used here to calculate feldspar dissolution rates in the Topopah Spring Tuff, the host rock for the proposed nuclear waste repository at Yucca Mountain, Nevada. The center of the tuff is a high silica rhyolite, consisting largely of alkali feldspar (???60 wt%) and quartz polymorphs (???35 wt%) that formed by devitrification of rhyolitic glass as the tuff cooled. First, the abundance of secondary aluminosilicates is used to estimate the cumulative amount of feldspar dissolution over the history of the tuff, and an ambient dissolution rate is calculated by using the estimated thermal history. Second, the feldspar dissolution rate is calculated by using measured Sr isotope compositions for the pore water and rock. Pore waters display systematic changes in Sr isotopic composition with depth that are caused by feldspar dissolution. The range in dissolution rates determined from secondary mineral abundances varies from 10-16 to 10-17 mol s-1 kg tuff-1 with the largest uncertainty being the effect of the early thermal history of the tuff. Dissolution rates based on pore water Sr isotopic data were calculated by treating percolation flux parametrically, and vary from 10-15 to 10-16 mol s-1 kg tuff-1 for percolation fluxes of 15 mm a-1 and 1 mm a-1, respectively. Reconciling the rates from the two methods requires that percolation fluxes at the sampled locations be a few mm a-1 or less. The calculated feldspar dissolution rates are low relative to other measured field-based feldspar dissolution rates, possibly due to the age (12.8 Ma) of the unsaturated system at Yucca Mountain; because oxidizing and organic-poor conditions limit biological activity; and/or because elevated silica concentrations in the pore waters (???50 mg L-1) may inhibit feldspar dissolution. ?? 2009 Elsevier Ltd. All rights reserved.

  11. EXPERIMENTAL STUDIES ON FELDSPAR ORE CONCENTRATION

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A series of Fe2O3-elimination experiments were conducted on feldspar samples from Tangshan Stone-powder Plant. These experimental methods include scrubbing desliming, flotation, rod milling and high gradient magnetic separation. Some technical factors of feldspar concentration and a new technological flow-sheet of ceramics raw material concentration were put forward.

  12. Equilibrium Kinetics and Isotherm Studies of Cu (II Adsorption from Waste Water onto Alkali Activated Oil Palm Ash

    Directory of Open Access Journals (Sweden)

    Zaira Z. Chowdhury

    2011-01-01

    Full Text Available Problem statement: Heavy metal accumulation in waste water could affect aquatic life, human health and overall ecosystem adversely. Therefore, in recent years much emphasis has been given for the use of industrial waste material as low cost adsorbents for removal of metallic contaminants from waste water. Approach: Present study deals with the adsorption equilibrium and kinetics of Cu (II cation using sodium hydroxide activated Oil Palm Ash (OPA. Adsorption was investigated in a batch system with respect to various parameters such as initial metal ion concentration, contact time and pH of the solution. Surface characterization of the prepared adsorbent was done by using surface area analyzer, Scanning Electron Microscope (SEM and X-ray Fluorescence and compared with natural oil palm ash. The adsorption equilibrium data were best represented by Langmuir, Freundlich and Temkin model. Equilibrium kinetics studies were performed by Pseudo first order, Pseudo second order and Intra-particle diffusion. Results: Maximum monolayer adsorption capacity observed at 30°C was 18.86 mg g−1. Kinetic data correlated well with the pseudo second order model, suggesting that the adsorption process might be chemical sorption. The linear plots of intra particle diffusion revealed that the adsorption process was mainly governed by pore diffusion. Equilibrium uptake was increased with increase of initial concentration and contact time. Experimental data showed that about 96.03% of copper can be removed at pH 5.5. Conclusion: The research concluded that activation by alkali treatment of natural OPA would produce sufficient porosities and surface area and it has got good potential to remove Cu (II from waste water.

  13. Using Neutron Diffraction to Determine the Low-Temperature Behavior of Pb2+ in Lead Feldspar

    Science.gov (United States)

    Kolbus, L. M.; Anovitz, L. M.; Chakoumackos, B. C.; Wesolowski, D. J.

    2014-12-01

    Feldspar minerals comprise 60% of the Earth's crust, so it imperative that the properties of feldspar be well understood for seismic modeling. The structure of feldspar consists of a three-dimensional framework of strongly-bonded TO4 tetrahedra formed by the sharing of oxygen atoms between tetrahedra. The main solid solution series found in natural feldspars are alkali NaAlSi3O8 -KAlSi3O8 and plagioclase CaAl2Si2O8-NaAlSi3O8. Recently, efforts have been made to systematically quantify feldspars structural change at non-ambient temperatures by considering only the relative tilts of the tetrahedral framework [1]. This serves as a tool to predict various behaviors of the structure such as the relative anisotropy of unit cell parameters and volume evolution with composition and temperature. Monoclinic feldspars are well predicted by the model [1], but discrepancies still remain between the model predictions and real structures with respect to absolute values of the unit cell parameters. To improve the existing model, a modification must be made to account for the M-cation interaction with its surrounding oxygen atoms. We have, therefore, chosen to study the structure of Pb-feldspar (PbAl2Si2O8), which provides the opportunity to characterize a monoclinic Al2Si2 feldspar containing a large M-site divalent cation using neutron diffraction. Neutron diffraction allows for the characterization of the M-site cation interaction between the oxygen atoms in the polyhedral cage by providing information to accurately determine the atomic displacement parameters.. Lead feldspar was synthesized for this study using the method described in [2], and confirmed to have a monoclinic C2/m space group. In this talk we will present structural determinations and atomic displacement parameters of Pb-feldspar from 10 - 300K generated from Neutron diffraction at the POWGEN beamline at the Spallation Neutron Source at Oak Ridge National lab, and compare our results to those predicted by the

  14. Spectral study on feldspar thermoluminescence process

    Institute of Scientific and Technical Information of China (English)

    GONG GeLian; LIU ShunSheng; XIA Bin; SUN WeiDong; HUANG BaoLin

    2008-01-01

    Feldspar thermoluminescence fading phenomena were investigated here by using newly-constructed thermoluminescence spectrometer on the basis of charge-cou-pled detector, and thereafter the discussion and explanation on feldspar TL fading mechanism were presented.The experimental results show that the fading rate of feldspar TL depends on both wavelength and stimulated temperature, and normally the feldspar TL in every region of wavelength and temperature shows different traits, namely the low temperature TL (170℃-190℃) fading at the rate of logarith-mic function and furthermore the TL of different wavelengths fading at approxi-mately the same rate on the condition of 160℃ preheating.While the medium and high temperature TLs (290℃-400℃) do not show much thermal fading, their fading rate at room temperature invariably correlates well with their wavelength, namely the longer TL wavelength, the slower TL fading rate.The thermal instability of traps and the quantum-mechanical tunneling effects can explain the above fading phe-nomena respectively.It is recognized that feldspar TL fading depends on its wave-length, and furthermore new aspects of the solid thermoluminescence process can be displayed by the combination of three-dimensional TL spectral analysis and thermal fading or anomalous fading of TL for feldspar.

  15. Spectral study on feldspar thermoluminescence process

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Feldspar thermoluminescence fading phenomena were investigated here by using newly-constructed thermoluminescence spectrometer on the basis of charge-cou-pled detector,and thereafter the discussion and explanation on feldspar TL fading mechanism were presented. The experimental results show that the fading rate of feldspar TL depends on both wavelength and stimulated temperature,and normally the feldspar TL in every region of wavelength and temperature shows different traits,namely the low temperature TL (170℃-190℃) fading at the rate of logarith-mic function and furthermore the TL of different wavelengths fading at approxi-mately the same rate on the condition of 160℃ preheating. While the medium and high temperature TLs (290℃-400℃) do not show much thermal fading,their fading rate at room temperature invariably correlates well with their wavelength,namely the longer TL wavelength,the slower TL fading rate. The thermal instability of traps and the quantum-mechanical tunneling effects can explain the above fading phe-nomena respectively. It is recognized that feldspar TL fading depends on its wave-length,and furthermore new aspects of the solid thermoluminescence process can be displayed by the combination of three-dimensional TL spectral analysis and thermal fading or anomalous fading of TL for feldspar.

  16. Luminescence characterization of a sodium rich feldspar

    Energy Technology Data Exchange (ETDEWEB)

    Correcher, V.; Sanchez M, L. [CIEMAT, Av. Complutense 22, 28040 Madrid (Spain); Garcia G, J. [MNCN-CSIC, c/ J. Gutierrez Abascal 2, Madrid 28006 (Spain); Rivera, T. [CICATA-IPN, Av. Legaria 694, 11500 Mexico D.F. (Mexico)

    2006-07-01

    This paper reports on the radioluminescence (RL) and thermoluminescence (TL) properties of a sodium rich feldspar ((Na,K)[AlSi{sub 3}O{sub 8}]) with a mean molecular composition of orthoclase (Or) and albite (Ab) of Or{sub 1}Ab{sub 99}. Despite the complexity of the luminescence signals of the sample, it is possible to determine six different emission bands at about 300, 380, 420, 460, 550 and 680 nm. The 300 nm emission can be associated to structural defects related to the recombination process in which the Na{sup +} ion diffusion-limited is involved. The UV-blue emission band at (i) 380 nm is characteristic of mineral phases containing SiO{sub 4} tetrahedral and could be related to intrinsic defects in the lattice, (ii) the 420 nm band could be associated to the presence of Cu (II) ions placed next to the hole traps or the recombination on a centre formed from a hole-oxygen atom adjacent to two Al atoms (Al-O-Al) and (iii) the 460 nm waveband could be due to the presence of Ti{sup 4+}. The green and red emissions are respectively associated to the presence of Mn{sup 2+} and Fe{sup 3+} ions. The ratio between the relative intensities, peaked at 290 (the more intense waveband) and 550 nm is about 10:1 in both TL and RL; this fact indicates that the efficiency of recombination centres does no changes regardless on the type of the process. (Author)

  17. ALKALI RESISTANT CATALYST

    DEFF Research Database (Denmark)

    2008-01-01

    The present invention concerns the selective removal of nitrogen oxides (NOx) from gasses. In particular, the invention concerns a process, a catalyst and the use of a catalyst for the selective removal of nitrogen oxides in the presence of ammonia from gases containing a significant amount...... of alkali metal and/or alkali-earth compounds which process comprises using a catalyst combined of (i) a formed porous superacidic support, said superacidic support having an Hammett acidity stronger than Ho=-12, and (ii) a metal oxide catalytic component deposited on said superacidic support selected from...

  18. Natural radioactivity and Rare Earth elements in feldspar samples, Central Eastern desert, Egypt

    Energy Technology Data Exchange (ETDEWEB)

    Walley El-Dine, Nadia, E-mail: nadia_walley5@hotmail.co [Department of physics, Faculty of girls for Art, Science and Education, Ain Shams University, Heliopolis, Cairo (Egypt); El-Shershaby, Amal [Department of physics, Faculty of girls for Art, Science and Education, Ain Shams University, Heliopolis, Cairo (Egypt); Afifi, Sofia [Nuclear Materials Authority (Egypt); Sroor, Amany; Samir, Eman [Department of physics, Faculty of girls for Art, Science and Education, Ain Shams University, Heliopolis, Cairo (Egypt)

    2011-05-15

    The pegmatite bodies of the Eastern Desert of Egypt are widely distributed especially along the Marsa-Alam-Idfu road. The Abu Dob area covers about 150 km{sup 2} of the Arabian Nubian shield at the central part of the Eastern Desert of Egypt. Most of the pegmatite is zoned; the zonation starts with milky quartz at the core followed by alkali feldspar at the margins. The feldspars vary in color from rose to milky and in composition from K-feldspar to Na-feldspar, sometimes interactions of both types are encountered. Thirteen feldspar samples were collected from different locations in the Abu Dob area for measuring the natural radioactivity of {sup 238}U, {sup 232}Th and {sup 40}K using an HPGe detector. The variation in concentration of radionuclides for the area under investigation can be classified into regions of high, medium and low natural radioactivity. The average concentration in BqKg{sup -1} has been observed to be from 9.5 to 183675.7 BqKg{sup -1} for {sup 238}U, between 6.1 and 94,314.2 BqKg{sup -1} for {sup 232}Th and from 0 to 7894.6 BqKg{sup -1} for {sup 40}K. Radium equivalent activities (Ra{sub eq}), dose rate (D{sub R}) and external hazard (H{sub ex}) have also been determined. In the present work, the concentration of rare earth elements are measured for two feldspar samples using two techniques, Environmental Scanning Electron microscope XIL 30 ESEM, Philips, and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). The existence of rare earth elements in this area are very high and can be used in different important industries.

  19. Natural radioactivity and rare earth elements in feldspar samples, Central Eastern desert, Egypt.

    Science.gov (United States)

    Walley El-Dine, Nadia; El-Shershaby, Amal; Afifi, Sofia; Sroor, Amany; Samir, Eman

    2011-05-01

    The pegmatite bodies of the Eastern Desert of Egypt are widely distributed especially along the Marsa-Alam-Idfu road. The Abu Dob area covers about 150km(2) of the Arabian Nubian shield at the central part of the Eastern Desert of Egypt. Most of the pegmatite is zoned; the zonation starts with milky quartz at the core followed by alkali feldspar at the margins. The feldspars vary in color from rose to milky and in composition from K-feldspar to Na-feldspar, sometimes interactions of both types are encountered. Thirteen feldspar samples were collected from different locations in the Abu Dob area for measuring the natural radioactivity of (238)U, (232)Th and (40)K using an HPGe detector. The variation in concentration of radionuclides for the area under investigation can be classified into regions of high, medium and low natural radioactivity. The average concentration in BqKg(-1) has been observed to be from 9.5 to 183675.7BqKg(-1) for (238)U, between 6.1 and 94,314.2BqKg(-1) for (232)Th and from 0 to 7894.6BqKg(-1) for (40)K. Radium equivalent activities (Ra(eq)), dose rate (D(R)) and external hazard (H(ex)) have also been determined. In the present work, the concentration of rare earth elements are measured for two feldspar samples using two techniques, Environmental Scanning Electron microscope XIL 30 ESEM, Philips, and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). The existence of rare earth elements in this area are very high and can be used in different important industries.

  20. Probing luminescence centers in Na rich feldspar

    DEFF Research Database (Denmark)

    Prasad, Amit Kumar; Lapp, Torben; Kook, Myung Ho;

    2016-01-01

    our understanding of the luminescence mechanisms and recombination sites, in a sample of Na rich plagioclase feldspar (oligoclase). Both the UV and violet–blue emissions show resonant excitations arising from a distribution of energy levels. We propose, contrary to the general understanding...

  1. Kinetics of infrared stimulated luminescence from feldspars

    DEFF Research Database (Denmark)

    Jain, Mayank; Sohbati, Reza; Guralnik, Benny;

    2015-01-01

    thermal and optical, of the infrared stimulated luminescence signal from feldspar. Based on the application of this model, it is concluded that different infra-red stimulated luminescence emissions (UV, blue, yellow and far-red) follow the same kinetics, and, therefore, involve participation of the same...

  2. Thermo-optical properties of optically stimulated luminescence in feldspars

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Bøtter-Jensen, L.; Johnsen, O.

    1995-01-01

    Optically stimulated luminescence processes in feldspars are subject to competing thermal enhancement and quenching processes: this article describes the thermal enhancement effects for orthoclase, albite and plagioclase feldspars. It is demonstrated that certain lattice vibrational modes can...

  3. Recent developments of OSL techniques for dating quartz and feldspars

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Jungner, H.; Mejdahl, V.

    1993-01-01

    The construction of a unit for measuring optically stimulated luminescence from quartz and feldspar is described. The light sources used for stimulation are infrared diodes for feldspar and green light from a halogen lamp (obtained with a system of filters) for both quartz and feldspar. The unit ...

  4. Synthesis of Leucite from Potash Feldspar

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yi; QU Chi; WU Jianqing; LU Ming; RA Pinggen; LIU Xiaoxi

    2008-01-01

    Leucite particles were synthesized from feldspar mixed with 0%to 52%potassium nitrate fired from 800℃to 1200℃by solid state method.The X-ray Diffraction(XRD)patterns show that in the temperature range from 800℃to 1200℃,the leucite can be removed as the single crystalline phase.Kalsilite may be crystallized with leucite at 800℃,but can be eliminated after prolonged heating.The scanning electron Microscopy(SEM) images clearly display the that crystals of micrometer scale leucite,and the leucite crystals distribute evenly in the matrix.The Thermal expansion coefficient(TEC)of the samples fabricated is as high as 20.52× 10-6℃-1 measured from 20℃to 500℃.The mechanism oftransformation from feldspar to leucite was proposed.

  5. Experimental study on removal of iron from potash feldspar

    Science.gov (United States)

    Kong, JW; Li, SQ; Miao, X.; Bai, JX; Yang, CQ

    2017-05-01

    The potassium feldspar ore in a certain area of Chengde contains K2O 9.82%, Na2O 2.41%, which belongs to the high quality feldspar ore. It cannot be exploited and utilized because of the high iron content. An experimental research was carried out to remove iron from a feldspar ores in this area by the technique of high gradient magnetic separation respectively. The properties of potassium feldspar ore were analyzed, and the technology for iron removal from potash feldspar ore was expounded. The optimum parameters were determined. Finally, the content of Fe2O3 in the potash feldspar was reduced from the original 0.88% to 0.082%, significantly reduced the content of Fe2O3. The effect of iron removal was ideal, and the products can meet the requirements of high-grade daily porcelain on feldspar raw materials.

  6. Feldspar minerals as efficient deposition ice nuclei

    Directory of Open Access Journals (Sweden)

    J. D. Yakobi-Hancock

    2013-06-01

    Full Text Available Mineral dusts are well known to be efficient ice nuclei, where the source of this efficiency has typically been attributed to the presence of clay minerals such as illite and kaolinite. However, the ice nucleating abilities of the more minor mineralogical components have not been as extensively examined. As a result, the deposition ice nucleation abilities of 24 atmospherically-relevant mineral samples have been studied, using a continuous flow diffusion chamber at −40.0 ± 0.3 °C. The same particle size (200 nm and particle preparation procedure were used throughout. The ice nucleation behaviour of the pure minerals is compared to that of complex mixtures, such as Arizona Test Dust (ATD and Mojave Desert Dust (MDD, and to lead iodide, which has been previously proposed for cloud seeding. Lead iodide was the most efficient ice nucleus (IN, requiring a critical relative humidity with respect to ice (RHi of 122.0 ± 2.0% to activate 0.1% of the particles. MDD (RHi 126.3 ± 3.4% and ATD (RHi 129.5 ± 5.1% have lower but comparable activity. From a set of clay minerals (kaolinite, illite, montmorillonite, non-clay minerals (e.g. hematite, magnetite, calcite, cerussite, quartz, and feldspar minerals (orthoclase, plagioclase present in the atmospheric dusts it was found that the feldspar minerals (particularly orthoclase, and not the clays, were the most efficient ice nuclei. Orthoclase and plagioclase were found to have critical RHi values of 127.1 ± 6.3% and 136.2 ± 1.3%, respectively. The presence of feldspars (specifically orthoclase may play a significant role in the IN behaviour of mineral dusts despite their lower percentage in composition relative to clay minerals.

  7. OSL-thermochronometry of feldspar from the KTB borehole, Germany

    DEFF Research Database (Denmark)

    Guralnik, Benny; Jain, Mayank; Herman, Frédéric;

    2015-01-01

    The reconstruction of thermal histories of rocks (thermochronometry) is a fundamental tool both in Earth science and in geological exploration. However, few methods are currently capable of resolving the low-temperature thermal evolution of the upper ∼2 km of the Earth's crust. Here we introduce...... the current geothermal gradient, or (ii) inverted into a geothermal palaeogradient of 29±2 °C km−1, integrating natural thermal conditions over the last ∼65 ka. The demonstrated ability to invert a depth–luminescence dataset into a meaningful geothermal palaeogradient opens new venues for reconstructing...... recent ambient temperatures of the shallow crust (200 °C Ma−1 range). Although Na-feldspar IRSL is prone to field saturation in colder or slower environments, the method's primary relevance appears to be for borehole and tunnel studies, where it may offer remarkably recent (...

  8. Investigation of zinc alkali pyrophosphate glasses. Part II: Local and medium range orders analysed by 1D/2D NMR

    Energy Technology Data Exchange (ETDEWEB)

    Rajbhandari, P. [UCCS UMR-CNRS 8181, Université de Lille1, Villeneuve d' Ascq (France); Chen, Y. [LASIR UMR-CNRS 8516, Université de Lille1, Villeneuve d' Ascq (France); Doumert, B. [IMMCL CNRS-FR2638, Université de Lille1, Villeneuve d' Ascq (France); Montagne, L. [UCCS UMR-CNRS 8181, Université de Lille1, Villeneuve d' Ascq (France); Tricot, G., E-mail: gregory.tricot@univ-lille1.fr [UCCS UMR-CNRS 8181, Université de Lille1, Villeneuve d' Ascq (France); LASIR UMR-CNRS 8516, Université de Lille1, Villeneuve d' Ascq (France)

    2015-04-01

    The structure of the (66-x)ZnO-xNa{sub 2}O-33.4P{sub 2}O{sub 5} composition line, selected for the development of low-Tg and stable glasses, has been investigated by 1D/2D NMR spectroscopy. If standard 1D {sup 31}P MAS-NMR experiments give access to the Q{sup n} speciation and show the presence of Q{sup 0}, Q{sup 1} and Q{sup 2} sites within the glass structure, application of the homonuclear through-space correlation technique ({sup 31}P DQ-SQ) allows for a more accurate description of the phosphate units. Clear distinction between the Q{sup 1} sites involved in dimmers or in longer chains has been derived from 2D NMR correlation maps and leads to the re-assignment of Q{sup 1} into Q{sup 1,1} and Q{sup 1,2} species. {sup 23}Na and {sup 23}Na({sup 31}P) REDOR MAS-NMR experiments have been used to analyse the Na{sup +} ions distribution and its interaction with the phosphate network. {sup 67}Zn static NMR experiments, performed at very high field, were carried out and suggest a constant Zn{sup 2+} coordination state all along the composition line. The results have been used to discuss the impact of the Zn{sup 2+}/Na{sup +} ratio on the extent of disorder within the glass network expressed in terms of Q{sup n} dismutation equilibrium constant and phosphate chain length distribution. - Highlights: • Structure of zinc alkali pyrophosphate glasses have been analysed by 1D/2D NMR. • 2D {sup 31}P experiments allow to separate Q{sup 1,1} and Q{sup 1,2} species. • {sup 67}Zn static NMR shows a constant signal all along the composition line.

  9. Alkali norite, troctolites, and VHK mare basalts from breccia 14304

    Science.gov (United States)

    Goodrich, Cyrena Anne; Taylor, G. Jeffrey; Keil, Klaus; Kallemeyn, Gregory W.; Warren, Paul H.

    1986-09-01

    Twelve clasts were separated from breccia 14304 for consortium study: six pristine highlands rocks, two mare basalts, and four nonpristine highlands rocks. The pristine highlands rocks include representatives of the magnesian troctolite-anorthosite and alkali suites, the two most common subgroups of the Mg suite found at the Apollo 14 site. Two troctolite clasts have olivine (~Fo 90) and plagioclase (~An 94) compositions similar to one group of Apolo 14 troctolites. One also contains spinel (Mg' 66-85). Incompatible element abundances in one are similar to those of 14305 troctolites, although the HREE (heavy rare earth elements) pattern is distinct among Apollo 14 troctolites. A dunite clast (~Fo 89) may be an unrepresentative piece of a troctolite. Alkali lithologies include an alkali anorthosite and an alkali norite, which is a rock type not previously described. The alkali norite has a pristine igneous texture and contains inverted pigeonite (Mg' 64), plagioclase (An82), K-feldspar, ternary feldspar, REE-rich phosphates, and silica. It resembles alkali gabbronorites from Apollo 14 and 67975 in mineralogy and mineral compositions. Alkali lithologies and phosphate-bearing magnesian anorthosites from Apollo 14 may have formed from Mg-rich magmas that assimilated various amounts of material rich in P and REE. This material could be a fractionated derivative of urKREEP. another pristine clast from 14304 is an Mg-gabbronorite. The two mare basalt clasts are very high potassium (VHK) basalts. They have 4 mg/g K and K/La ratios of 580 and 700. The parent magmas of VHK basalts could have formed from typical low-Ti, high-Al basaltic magmas by assimilation of K-rich material. This material could also be a fractionated derivative or urKREEP. Nonpristine 14304 clasts include melt-textured anorthosites and an augite-rich poikilitic melt rock. The latter is probably polymict, but its major component must be an Mg-suite gabbro.

  10. Alkali-ions diffusion, mullite formation, and crystals dissolution during sintering of porcelain bodies: Microstructural approach

    DEFF Research Database (Denmark)

    Leonelli, C.; Kamseu, E.; Boccaccini, Dino

    2009-01-01

    The effect of alkali-silicate glassy matrix as replacement for feldspar in soft and hard porcelain compositions was studied. SEM and X-ray diffraction analysis were used to evidence phase evolution. For each composition, the influence of soaking time was evaluated. The difference in chemical...

  11. Photoionization in alkali lasers.

    Science.gov (United States)

    Knize, R J; Zhdanov, B V; Shaffer, M K

    2011-04-11

    We have calculated photoionization rates in alkali lasers. The photoionization of alkali atoms in the gain medium of alkali lasers can significantly degrade the laser performance by reducing the neutral alkali density and with it the gain. For a ten atmosphere Rb laser and a Cs exciplex laser, the photoionization induced alkali atom loss rates are greater than 10(5) sec(-1). These high loss rates will quickly deplete the neutral alkali density, reducing gain, and may require fast, possibly, supersonic flow rates to sufficiently replenish the neutral medium for CW operation.

  12. EPR, ELDOR, and ENDOR studies of alkali metal- o-dimesitoylbenzene radical complexes in solution. II. The lithium and sodium complexes

    Science.gov (United States)

    van der Drift, E.; Smidt, J.

    A combined EPR-ELDOR-ENDOR study on ion pairs of o-dimesitoylbenzene anions with Li or Na cations provides a unique description of the alkali relaxation pattern in terms of dipolar and quadrupolar relaxation resulting from molecular tumbling. Internal motions in the chelating ring structure appear to be of minor importance. From the EPR and ELDOR results a variety of structural information is obtained: spectral densities, rotational correlation time of the complex, and anisotropic magnetic interactions of the alkali nucleus.

  13. Understanding optically stimulated charge movement in quartz and feldspar using time-resolved measurements

    Energy Technology Data Exchange (ETDEWEB)

    Ankjaergaard, C.

    2010-02-15

    Thermoluminescence (TL) and optically stimulated luminescence (OSL) from quartz and feldspar are widely used in accident dosimetry and luminescence dating. In order to improve already existing methods or to develop new methods towards extending the current limits of the technique, it is important to understand the charge movement within these materials. Earlier studies have primarily focussed on examination of the trap behaviour; however, this only tells half of the story as OSL is a combination of charge stimulation and recombination. By using time-resolved OSL (TR-OSL), one can directly examine the recombination route(s), and thus obtain insight into the other half of the process involved in luminescence emission. This thesis studies the TR-OSL and optically stimulated phosphorescence signals from quartz and feldspars spanning several orders of magnitude in time (few ns to the seconds time scale) in order to identify various charge transport mechanisms in the different time regimes. The techniques employed are time-resolved OSL, continuous-wave OSL, TL, optically stimulated exo-electron (OSE) emission and time-resolved OSE. These different techniques are used in combination with variable thermal or optical stimulation energy. The thesis first delves into three main methodological developments, namely (i) research and development of the equipment for TR-OSL measurements, (ii) finding the best method for multiple-exponential analysis of a TR-OSL curve, and (iii) optimisation of the pulsing configuration for the best separation of quartz OSL from a mixed quarts-feldspar sample. It then proceeds to study the different charge transport mechanisms subsequent to an optical stimulation pulse in quartz and feldspars. The results obtained for quartz conclude that the main lifetime component in quartz represents an excited state lifetime of the recombination centre, and the more slowly decaying components on the millisecond to seconds time scale arise from charge recycling

  14. Milk-alkali syndrome

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000332.htm Milk-alkali syndrome To use the sharing features on this page, please enable JavaScript. Milk-alkali syndrome is a condition in which there ...

  15. Feldspar Variability in Northwest Africa 7034

    Science.gov (United States)

    Santos, A. R.; Lewis, J. A.; Agee, C. B.; Humayun, M.; McCubbin, F. M.; Shearer, C. K.

    2017-01-01

    The martian meteorite Northwest Africa 7034 (and pairings) is a breccia that provides important information about the rocks and processes of the martian crust (e.g., 1-3). Additional information can be gleaned from the components of the breccia. These components, specifically those designated as clasts, record the history of their parent rock (i.e., the rock that has been physically broken down to produce the clasts). In order to study these parent rocks, we must first determine which clasts within the breccia are de-rived from the same parent. Previous studies have be-gun this process (e.g., 4), but the search for genetic linkages between clasts has not integrated clasts with different grain sizes. We begin to take this approach here, incorporating igneous-textured clasts with both fine and coarse mineral grains. In NWA 7034, almost all materials (clasts and breccia matrix) are composed of the same mineral assemblages (feldspar, pyroxene, Fe-Ti oxides, apatite) with largely the same mineral compositions [1, 4-6]. Bulk breccia Sm-Nd systematics define a single isochron [7]. These observations are consistent with a majority of the components within NWA 7034 originating from the same geochemical source and crystallizing at roughly the same time.

  16. Alkali control of high-grade metamorphism and granitization

    Directory of Open Access Journals (Sweden)

    Oleg G. Safonov

    2014-09-01

    Full Text Available We review petrologic observations of reaction textures from high-grade rocks that suggest the passage of fluids with variable alkali activities. Development of these reaction textures is accompanied by regular compositional variations in plagioclase, pyroxenes, biotite, amphibole and garnet. The textures are interpreted in terms of exchange and net-transfer reactions controlled by the K and Na activities in the fluids. On the regional scale, these reactions operate in granitized, charnockitized, syenitized etc. shear zones within high-grade complexes. Thermodynamic calculations in simple chemical systems show that changes in mineral assemblages, including the transition from the hydrous to the anhydrous ones, may occur at constant pressure and temperature due only to variations in the H2O and the alkali activities. A simple procedure for estimating the activity of the two major alkali oxides, K2O and Na2O, is implemented in the TWQ software. Examples of calculations are presented for well-documented dehydration zones from South Africa, southern India, and Sri Lanka. The calculations have revealed two end-member regimes of alkalis during specific metamorphic processes: rock buffered, which is characteristic for the precursor rocks containing two feldspars, and fluid-buffered for the precursor rocks without K-feldspar. The observed reaction textures and the results of thermodynamic modeling are compared with the results of available experimental studies on the interaction of the alkali chloride and carbonate-bearing fluids with metamorphic rocks at mid-crustal conditions. The experiments show the complex effect of alkali activities in the fluid phase on the mineral assemblages. Both thermodynamic calculations and experiments closely reproduce paragenetic relations theoretically predicted by D.S. Korzhinskii in the 1940s.

  17. On the relationship between luminescence excitation spectra and feldspar mineralogy

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Bøtter-Jensen, L.; Johnsen, O.

    1996-01-01

    Feldspar minerals can be used as naturally occurring radiation dosemeters, with dose assessment commonly using luminescence techniques. Since many feldspars contain radioactive K-40, knowledge of the mineralogy of the luminescent samples being measured is of high importance. Most feldspars contain...... more than trace amounts of highly luminescent Fe3+ impurities, and this article examines the relationship between features of the luminescence excitation spectrum of this ion with sample mineralogy. It is demonstrated that there is a near linear correspondence between the plagioclase feldspar...... groups. The results are compared with properties of the excitation spectra dose-dependent optically stimulated luminescence (OSL) in order to compare the chemical environment of the OSL donor defect, and the isolated Fe3+ centres....

  18. Directed reflectivity, long life AMTEC condenser (DRC). Final report of Phase II SBIR program[Alkali Metal ThermoElectric Converter

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, Thomas K.

    2001-09-10

    The Alkali Metal Thermal to Electric Converter (AMTEC) is a static energy conversion device that operates at high thermal to electric conversion efficiencies that are essentially independent of size, have reached 19% and are expected to reach 25% to 30% in 1997. AMTEC systems have been chosen by NASA and DOE for spacecraft applications and have considerable promise for a wide variety of terrestrial applications. Reduction of parasitic heat losses in AMTEC systems related to radiative heat transfer from the hot side to the condenser can make a substantial contribution to system efficiency. Through design, analysis and the fabrication and testing of cells and systems, the proposed program to develop a Directed Reflectivity Condenser (DRC) has investigated the feasibility of an improved AMTEC condenser component. Phase 1 work showed the potential for adding from 4% to 7% to overall system efficiency for identical operating conditions using the concept. A detailed thermal analysis of several DRC capped cell designs was carried out and some of the conditions under which a DRC, used as the condenser at an end cap of a cylindrical converter, can reduce thermal radiation related losses were determined. A model experimental converter was built and tested to compare DRC and planar condenser surfaces. The results of both analysis and experiment indicate that for moderate aspect ratios of a cylindrical, end condensed converter, the DRC can reduce overall thermal losses by up to 4%. The initial effort in Phase 2 extended the analysis to a novel 150 watt radial AMTEC cell design. This analysis indicated that for the effective aspect ratio of this new converter design, the system performance at the 100+ watt level was not significantly improved by use of a DRC type condenser surface. Further analyses however showed that for cylindrical, end-condensed converters, optimized for use with internal radiation shields, the use of DRC surfaces on the side walls of the converter could be

  19. Immersion Freezing of Potassium-feldspar and related Natural Samples

    Science.gov (United States)

    Zolles, Tobias; Burkart, Julia; Grothe, Hinrich

    2014-05-01

    Ice nucleation activities of mineral dust particles were investigated. The experiments were carried out using cryo-microscopy which is an oil-emulsion based method. The immersion freezing mode was addressed with this experimental setup. The studied samples were common inorganic atmospheric aerosols. Single minerals and natural samples were tested [1]. Mineral dust particles are active ice nuclei in the immersion freezing mode up to 256 K. Only recently potassium-feldspar has been identified as the by far most active ice nucleus followed by other silicates [2, 3]. Natural samples which contain more than 5% K-feldspar are also active. The activity of K-feldspar can be attributed to its surface structure and the presence of potassium ions in the surface. Ice nucleation on mineral dust particles takes place at certain nucleation sites. These sites are domains of molecular sites where water is stabilized in an ice-like structure. To form a good ice nucleation site, the site density of molecular sites needs to be high. More molecular sites are able to form larger domains on the surface, leading to better nucleation sites. This suggests further that the nucleation temperature of mineral dust particles scales with the surface area. The exact configuration of a molecular site is material specific and influenced by the local chemistry and structure of the dust particle surface. A favourable arrangement of the functional groups like surface hydroxyl and oxygen is proposed for the K-feldspar. Potassium ions seem to have a positive or neutral effect on the ice nucleation property of a silicate surface while cations with a higher charge density like calcium and sodium have a negative influence. K-feldspar is abundant in the environment and actually is the most important dust ice nucleus in the atmosphere. The nucleation temperatures of the K-feldspar particles are sufficient to enable further meteorological glaciation processes in high altitude clouds. References [1] Zolles, T

  20. Developing a numerical simulation for fading in feldspar

    DEFF Research Database (Denmark)

    Larsen, A.; Greilich, Steffen; Jain, Mayank;

    2009-01-01

    Most models describing anomalous fading in feldspars are based on analytical solutions. As an alternative approach we present an entirely numerical model based on statistical sampling that simulates stepwise the charge creation/trapping and recombination in a given phosphor. We assume the number...

  1. Luminescence from potassium feldspars stimulated by infrared and green light

    DEFF Research Database (Denmark)

    Duller, G.A.T.; Bøtter-Jensen, L.

    1993-01-01

    A series of experiments are reported which investigate stimulated luminescence from potassium feldspar. The aim is to provide a basic phenomenological description of the response of the material to stimulation by heat, infrared radiation (875 DELTA 80 nm) and a green light wavelength band from 5 15...

  2. Stability of IRSL signals from sedimentary K-feldspar samples

    DEFF Research Database (Denmark)

    Thomsen, Kristina Jørkov; Murray, A.S.; Jain, Mayank

    2011-01-01

    for potassium-rich sedimentary feldspars. We show that the natural post-IR IRSL (pIRIR) signal from a 3.6 Ma old sample is in apparent saturation on a laboratory generated dose response curve, i.e. it does not show detectable fading in nature although a low fading rate is observed on laboratory time scales. We...

  3. Time-resolved luminescence from feldspars: New insight into fading

    DEFF Research Database (Denmark)

    Tsukamoto, S.; Denby, P.M.; Murray, A.S.

    2006-01-01

    Time-resolved infrared optically stimulated luminescence (IR-OSL) signals of K- and Na-feldspar samples extracted from sediments were measured in UV, blue and red detection windows, using a fast photon counter and pulsed IR stimulation (lambda = 875 nm). We observe that the relative contribution...

  4. Feldspars as a source of nutrients for microorganisms

    Science.gov (United States)

    Rogers, J.R.; Bennett, P.C.; Choi, W.J.

    1998-01-01

    Phosphorus and nitrogen are essential macronutrients necessary for the survival of virtually all living organisms. In groundwater systems, these nutrients can be quite scarce and can represent limiting elements for growth of subsurface microorganisms. In this study we examined silicate sources of these elements by characterizing the colonization and weathering of feldspars in situ using field microcosms. We found that in carbon-rich anoxic groundwaters where P and N are scarce, feldspars that contain inclusions of P-minerals such as apatite are preferentially colonized over similar feldspars without P. A microcline from S. Dakota, which contains 0.24% P2O5 but ,1 mmol/ g NH , was heavily colonized 1 4 and deeply weathered. A similar microcline from Ontario, which has no detectable P or NH , was barren of attached organisms and completely unweathered after one year. An- 1 4 orthoclase (0.28% P2O5, ;1 mmol/g NH ) was very heavily colonized and weathered, 1 4 whereas plagioclase specimens (,0.01% P, ,1 mmmol/g NH ) were uncolonized and 1 4 unweathered. In addition, the observed weathering rates are faster than expected based on laboratory rates. We propose that this system is particularly sensitive to the availability of P, and the native subsurface microorganisms have developed biochemical strategies to aggressively scavenge P (or some other essential nutrient such as Fe31 ) from resistant feldspars. The result of this interaction is that only minerals containing P will be signifi- cantly colonized, and these feldspars will be preferentially destroyed, as the subsurface microbial community scavenges a limiting nutrient.

  5. Climatic aridity over India 11,000 years ago: Evidence from feldspar distribution in shelf sediments

    Digital Repository Service at National Institute of Oceanography (India)

    Hashimi, N.H.; Nair, R.R.

    Feldspars and quartz contents of sand and silt fractions of forty three samples from the western continental shelf of India were determined by the X-ray diffraction method. The results indicate that the feldspar content in the relict (9000...

  6. Wear and flexural strength comparisons of alumina/feldspar resin infiltrated dental composites.

    Science.gov (United States)

    Le Roux, A R; Lachman, N; Walker, M; Botha, T

    2008-11-01

    Incorporating a feldspar chemical bond between alumina filler particles is expected to increase the wear-resistant and flexural strength properties. An investigation was carried out to evaluate the influence of the feldspar chemical bonding between alumina filler particles on wear and flexural strength of experimental alumina/feldspar dental composites. It was hypothesized that wear resistance and flexural strength would be significantly increased with increased feldspar mass. Alumina was chemically sintered and bonded with 30% and 60% feldspar mass, silanized and infiltrated with UDMA resin to prepare the dental restorative composite material. Higher wear-resistant characteristics resulted with increased feldspar mass of up to 60% (p 0.05). Feldspar chemical bonding between the alumina particles may improve on the wear-resistance and flexural strength of alumina/feldspar composites.

  7. Selection of non-adsorbing alkali components

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.D.; Natesan, K.; Swift, W.M.

    1992-11-01

    This project consists of three phases of laboratory experimental study. In phase I (screening), eight candidate materials, 304SS (serves as a base material for comparison), Hastelloy C-276, Hastelloy X, Haynes No. 188, Allonized 304SS, Pt-coated 304SS, and ceramic-coated 304SS, will be subjected to atmospheric TGA study under the simulated PFBC (oxidizing) environment with and without alkali vapor doping. Each candidate material will be evaluated for its resistance toward alkali-vapor capture. In addition, a post-test metallographic characterization of the sample will be performed to obtain a better understanding of the alkali capture mechanism and material behavior. The material(s) with little or no alkali-vapor adsorption will be selected as the promising material(s) for the Phase II study. In Phase II, the promising material(s) will be further tested in the TGA under elevated pressure to simulate the PFBC environment (in terms of temperature, pressure, and gas composition). The effect of pressure on the extent of alkali-vapor adsorption will be evaluated, and the test samples will be metallographically characterized. The most promising candidate material(s) will be identified and recommended for further tesfing in the actual PFBC environment. In Phase III, four materials will be selected from the eight candidate materials screened in the PFBC environment and will be evaluated for their alkali-vapor capture by atmospheric TGA under the coal gasification fuel gas (reducing) environment. The tested samples will also be metallographically characterized. The most promising material(s) will be identified and recommended for further testing in the actual coal gasification environment.

  8. Selection of non-adsorbing alkali components

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.D.; Natesan, K.; Swift, W.M.

    1992-01-01

    This project consists of three phases of laboratory experimental study. In phase I (screening), eight candidate materials, 304SS (serves as a base material for comparison), Hastelloy C-276, Hastelloy X, Haynes No. 188, Allonized 304SS, Pt-coated 304SS, and ceramic-coated 304SS, will be subjected to atmospheric TGA study under the simulated PFBC (oxidizing) environment with and without alkali vapor doping. Each candidate material will be evaluated for its resistance toward alkali-vapor capture. In addition, a post-test metallographic characterization of the sample will be performed to obtain a better understanding of the alkali capture mechanism and material behavior. The material(s) with little or no alkali-vapor adsorption will be selected as the promising material(s) for the Phase II study. In Phase II, the promising material(s) will be further tested in the TGA under elevated pressure to simulate the PFBC environment (in terms of temperature, pressure, and gas composition). The effect of pressure on the extent of alkali-vapor adsorption will be evaluated, and the test samples will be metallographically characterized. The most promising candidate material(s) will be identified and recommended for further tesfing in the actual PFBC environment. In Phase III, four materials will be selected from the eight candidate materials screened in the PFBC environment and will be evaluated for their alkali-vapor capture by atmospheric TGA under the coal gasification fuel gas (reducing) environment. The tested samples will also be metallographically characterized. The most promising material(s) will be identified and recommended for further testing in the actual coal gasification environment.

  9. Phosphate and feldspar mineralogy of equilibrated L chondrites: The record of metasomatism during metamorphism in ordinary chondrite parent bodies

    Science.gov (United States)

    Lewis, Jonathan A.; Jones, Rhian H.

    2016-10-01

    In ordinary chondrites (OCs), phosphates and feldspar are secondary minerals known to be the products of parent-body metamorphism. Both minerals provide evidence that metasomatic fluids played a role during metamorphism. We studied the petrology and chemistry of phosphates and feldspar in petrologic type 4-6 L chondrites, to examine the role of metasomatic fluids, and to compare metamorphic conditions across all three OC groups. Apatite in L chondrites is Cl-rich, similar to H chondrites, whereas apatite in LL chondrites has lower Cl/F ratios. Merrillite has similar compositions among the three chondrite groups. Feldspar in L chondrites shows a similar equilibration trend to LL chondrites, from a wide range of plagioclase compositions in petrologic type 4 to a homogeneous albitic composition in type 6. This contrasts with H chondrites which have homogeneous albitic plagioclase in petrologic types 4-6. Alkali- and halogen-rich and likely hydrous metasomatic fluids acted during prograde metamorphism on OC parent bodies, resulting in albitization reactions and development of phosphate minerals. Fluid compositions transitioned to a more anhydrous, Cl-rich composition after the asteroid began to cool. Differences in secondary minerals between H and L, LL chondrites can be explained by differences in fluid abundance, duration, or timing of fluid release. Phosphate minerals in the regolith breccia, Kendleton, show lithology-dependent apatite compositions. Bulk Cl/F ratios for OCs inferred from apatite compositions are higher than measured bulk chondrite values, suggesting that bulk F abundances are overestimated and that bulk Cl/F ratios in OCs are similar to CI.

  10. Sr and Pb isotopic geochemistry of feldspars and implications for the growth of megacrysts in plutonic settings.

    Science.gov (United States)

    Munnikhuis, J.; Glazner, A. F.; Coleman, D. S.; Mills, R. D.

    2015-12-01

    Why megacrystic textures develop in silicic igneous rocks is still unknown. One hypothesis is that these crystals nucleate early in a magma chamber with a high liquid content. A supportive observation of this hypothesis is areas in plutons with high concentrations of megacrysts suggesting flow sorting. Another group of hypotheses suggest megacrystic textures form during protracted late-stage coarsening in a low-melt, interlocked matrix due to either thermal oscillations from incremental pluton emplacement, or Ostwald ripening. Isotopic analyses of large, euhedral K-feldspar megacrysts from the Cretaceous intrusive suites of the Sierra Nevada batholith (SNB) provide new insight into their origin. Megacrysts from the SNB reach the decimeter scale, are Or rich (85-90%), are perthitic, and host mineral inclusions of nearly all phases in the host rock. In-situ micro-drilling of transects, from core to rim, of the alkali feldspars provides material for Sr and Pb isotopic analyses by thermal ionization mass spectrometry (TIMS). Preliminary 87Sr/86Sr(i) isotopic data from samples from the Cathedral Peak Granodiorite, of the Tuolumne Intrusive Suite range from 0.706337 to 0.706452 (~1.6ɛSr) near the cores, whereas a sawtooth pattern with larger variability, 0.706179 to 0.706533 (~5ɛSr), occurs nears the rims. We interpret these preliminary data to indicate that the late portion of growth (i.e. crystal rim) was dominated by either cannibalism of small K-feldspar crystals with isotopic variability, or by addition of isotopically diverse late components to the magma. By comparing the Sr and Pb isotopic stratigraphy of megacrysts from a variety of rock matrices and different granitoids in the SNB isotopic trends can be evaluated to determine if crystals sizes are dependent on disequilibrium processes or grow at a steady state.

  11. Bio-beneficiation of kaolin and feldspar and its effect on fired characteristics of triaxial porcelain

    Indian Academy of Sciences (India)

    Anandita Roy; Samarendra K Singh; P C Banerjee; Kausik Dana; Swapan Kumar Das

    2010-06-01

    Presence of iron compounds as impurities in kaolin and feldspar, impart reddish colour to ceramic products manufactured using these minerals. The quality of kaolin and feldspar was enriched mainly through iron removal by biological methods. Bacteria isolated from kaolin of Indian origin were used for bioleaching. Biotreatment of kaolin and feldspar using indigenous bacteria not only lowered the iron content of the minerals but also improved their whiteness. The porcelain prepared with these biobeneficiated minerals was compared to that prepared with non-beneficiated one. Physico-mechanical properties of porcelain were distinctly improved by using biobeneficiated kaolin and feldspar, without affecting the individual mineralogical compositions of kaolin and feldspar.

  12. Water Content of Lunar Alkali Fedlspar

    Science.gov (United States)

    Mills, R. D.; Simon, J. I.; Wang, J.; Alexander, C. M. O'D.; Hauri, E. H.

    2016-01-01

    Detection of indigenous hydrogen in a diversity of lunar materials, including volcanic glass, melt inclusions, apatite, and plagioclase suggests water may have played a role in the chemical differentiation of the Moon. Spectroscopic data from the Moon indicate a positive correlation between water and Th. Modeling of lunar magma ocean crystallization predicts a similar chemical differentiation with the highest levels of water in the K- and Th-rich melt residuum of the magma ocean (i.e. urKREEP). Until now, the only sample-based estimates of water content of KREEP-rich magmas come from measurements of OH, F, and Cl in lunar apatites, which suggest a water concentration of water content of the magma ocean would have water contents of 320 ppm for the bulk Moon and 1.4 wt % for urKREEP from plagioclase in ferroan anorthosites. Results and interpretation: NanoSIMS data from granitic clasts from Apollo sample 15405,78 show that alkali feldspar, a common mineral in K-enriched rocks, can have approx. 20 ppm of water, which implies magmatic water contents of approx. 1 wt % in the high-silica magmas. This estimate is 2 to 3 orders of magnitude higher than that estimated from apatite in similar rocks. However, the Cl and F contents of apatite in chemically similar rocks suggest that these melts also had high Cl/F ratios, which leads to spuriously low water estimates from the apatite. We can only estimate the minimum water content of urKREEP (+ bulk Moon) from our alkali feldspar data because of the unknown amount of degassing that led to the formation of the granites. Assuming a reasonable 10 to 100 times enrichment of water from urKREEP into the granites produces an estimate of 100-1000 ppm of water for the urKREEP reservoir. Using the modeling of and the 100-1000 ppm of water in urKREEP suggests a minimum bulk silicate Moon water content between 2 and 20 ppm. However, hydrogen loss was likely very significant in the evolution of the lunar mantle. Conclusions: Lunar granites

  13. Further investigations on 'non-fading' in K-Feldspar

    DEFF Research Database (Denmark)

    Jain, Mayank; Buylaert, Jan-Pieter; Thomsen, Kristina Jørkov;

    2015-01-01

    We give a theoretical overview of non-fading infrared stimulated luminescence (IRSL) signals in feldspars, followed by intercomparison of potential methods on some sediment extracts. We observe that a more stringent thermal wash on its own is not effective in obtaining a more stable signal......, suggesting that the higher the stimulation temperature in post IR-IRSL methods, the greater the ability to access distant electron hole pairs. We further find that the delayed off-time signal in time-resolved IRSL has immense potential for sampling non-fading signal and should be explored further...

  14. Luminescence from potassium feldspars stimulated by infrared and green light

    DEFF Research Database (Denmark)

    Duller, G.A.T.; Bøtter-Jensen, L.

    1993-01-01

    A series of experiments are reported which investigate stimulated luminescence from potassium feldspar. The aim is to provide a basic phenomenological description of the response of the material to stimulation by heat, infrared radiation (875 DELTA 80 nm) and a green light wavelength band from 5 15...... to 560 nm. Two conclusions are drawn: firstly it is suggested that the majority of the trapped charge responsible for the infrared stimulated luminescence signal does not give rise to a thermoluminescence signal, and secondly that a large traction of the two optically stimulated luminescence signals...

  15. Alkali basalts and enclosed ultramafic xenoliths near Ushuaia, Tierra Del Fuego, Argentina.

    Science.gov (United States)

    Acevedo, Rogelio Daniel

    2016-01-01

    At the southernmost part of Tierra del Fuego a few outcrops and erratic boulders of alkali basaltic rocks with ultramafic enclaves have been studied. Alkali basalt plugs or pipes hitherto identified are scarce, and host rocks are constituted by slates that belong to Mesozoic deposition. The petrography, texture and composition of the basalt and xenoliths were investigated by petrographic microscope and electron microprobe analysis. Xenocrysts of amphibole and alkali feldspar, phenocrysts of nepheline, olivine, spinel, phlogopite and Fe-Ti minerals (10 %) and a diversity of xenoliths, mainly lherzolitic, pyroxenite and wehrlitic nodules (15 %), but also from metamorphic rocks provenance, are contained in the basalt groundmass (75 %). This finer-grained material is made up of laths or needles of plagioclase, pyroxene, opaque minerals, apatite and glass, with intersertal, hyalopilitic and pilotaxitic. Locally, rock has an even granoblastic texture. Former amygdules are filled by analcite, zeolites, sodalite and calcite. The normative classification, based on nepheline content, conclude that this rock is an alkali basalt. The chemical classification, considering immobile elements as Zr/TiO2 versus Nb/Y indicate an alkali basalt too and plots over the TAS diagram fall in the foidite (Na-rich or nephelinite) and basanite fields. The REE patterns are fractionated (La/Yb primitive mantle normalized is approximately 30). The K-Ar isotopic technique on individual macrocrysts gave ages of 146 ± 5 Ma (amphibole) and 127 ± 4 Ma (alkali feldspar); and K-Ar whole rock datum reported 8.3 ± 0.3 Ma. Nevertheless, fertile samples show geochemical features typical of deep derived material thus, based on the position in the actual tectonic setting, indicate that the basalt is older than its isotopic age.

  16. Alkali elemental and potassium isotopic compositions of Semarkona chondrules

    Science.gov (United States)

    Alexander, C.M. O'D.; Grossman, J.N.

    2005-01-01

    We report measurements of K isotope ratios in 28 Semarkona chondrules with a wide range of petrologic types and bulk compositions as well as the compositions of CPX-mesostasis pairs in 17 type I Semarkona chondrules, including two chondrules with radial alkali zonation and 19 type II chondrules. Despite the wide range in K/Al ratios, no systematic variations in K isotopic compositions were found. Semarkona chondrules do not record a simple history of Rayleigh-type loss of K. Experimentally determined evaporation rates suggest that considerable alkali evaporation would have occurred during chondrule formation. Nevertheless, based on Na CPX-mesostasis distribution coefficients, the alkali contents of the cores of most chondrules in Semarkona were probably established at the time of final crystallization. However, Na CPX-mesostasis distribution coefficients also show that alkali zonation in type I Semarkona chondrules was produced by entry of alkalis after solidification, probably during parent body alteration. This alkali metasomatism may have gone to completion in some chondrules. Our preferred explanation for the lack of systematic isotopic enrichments, even in alkali depleted type I chondrule cores, is that they exchanged with the ambient gas as they cooled. ?? The Meteoritical Society, 2005.

  17. Chemical Zoning of Feldspars in Lunar Granitoids: Implications for the Origins of Lunar Silicic Magmas

    Science.gov (United States)

    Mills, R. D; Simon, J. I.; Alexander, C.M. O'D.; Wang, J.; Christoffersen, R.; Rahman, Z..

    2014-01-01

    Fine-scale chemical and textural measurements of alkali and plagioclase feldspars in the Apollo granitoids (ex. Fig. 1) can be used to address their petrologic origin(s). Recent findings suggest that these granitoids may hold clues of global importance, rather than of only local significance for small-scale fractionation. Observations of morphological features that resemble silicic domes on the unsampled portion of the Moon suggest that local, sizable net-works of high-silica melt (>65 wt % SiO2) were present during crust-formation. Remote sensing data from these regions suggest high concentrations of Si and heat-producing elements (K, U, and Th). To help under-stand the role of high-silica melts in the chemical differentiation of the Moon, three questions must be answered: (1) when were these magmas generated?, (2) what was the source material?, and (3) were these magmas produced from internal differentiation. or impact melting and crystallization? Here we focus on #3. It is difficult to produce high-silica melts solely by fractional crystallization. Partial melting of preexisting crust may therefore also have been important and pos-sibly the primary mechanism that produced the silicic magmas on the Moon. Experimental studies demonstrate that partial melting of gabbroic rock under mildly hydrated conditions can produce high-silica compositions and it has been suggested by that partial melting by basaltic underplating is the mechanism by which high-silica melts were produced on the Moon. TEM and SIMS analyses, coordinated with isotopic dating and tracer studies, can help test whether the minerals in the Apollo granitoids formed in a plutonic setting or were the result of impact-induced partial melting. We analyzed granitoid clasts from 3 Apollo samples: polymict breccia 12013,141, crystalline-matrix breccia 14303,353, and breccia 15405,78

  18. The calcium-alkali syndrome

    OpenAIRE

    Arroyo, Mariangeli; Fenves, Andrew Z.; Emmett, Michael

    2013-01-01

    The milk-alkali syndrome was a common cause of hypercalcemia, metabolic alkalosis, and renal failure in the early 20th century. It was caused by the ingestion of large quantities of milk and absorbable alkali to treat peptic ulcer disease. The syndrome virtually vanished after introduction of histamine-2 blockers and proton pump inhibitors. More recently, a similar condition called the calcium-alkali syndrome has emerged as a common cause of hypercalcemia and alkalosis. It is usually caused b...

  19. Sapropels and the age of hominins Omo I and II, Kibish, Ethiopia.

    Science.gov (United States)

    McDougall, Ian; Brown, Francis H; Fleagle, John G

    2008-09-01

    The provenance and age of two Homo sapiens fossils (Omo I and Omo II) from the Kibish Formation in southern Ethiopia have been much debated. Here we confirm that Omo I and the somewhat more primitive-looking Omo II calvariae are from similar stratigraphic levels in Member I of the Kibish Formation. Based on (40)Ar/(39)Ar age measurements on alkali feldspar crystals from pumice clasts in the Nakaa'kire Tuff, a tuffaceous bed in Member I just below the hominin levels, we place an older limit of 198+/-14 ka (weighted mean age=196+/-2 ka) for the hominins. A younger limit of 104+/-7 ka (weighted mean age=104+/-1 ka) is provided by feldspars separated from pumice clasts in the Aliyo Tuff in Member III. Geological evidence indicates rapid deposition of each member of the Kibish Formation, concurrent with deposition of sapropels in the Mediterranean Sea. The (40)Ar/(39)Ar age measurements, together with correlations with sapropels, indicate that the hominin fossils are close in age to the older limit. Our preferred estimate of the age of the hominins is 195+/-5 ka, making them the earliest well-dated anatomically modern humans yet described.

  20. Alkali Aggregate Reaction in Alkali Slag Cement Mortars

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    By means of "Mortar Bar Method",the ratio of cement to aggregate was kept as a constant 1∶2.25,the water-cement ratio of the mixture was 0.40,and six prism specimens were prepared for each batch of mixing proportions with dimensions of 10×10×60mm3 at 38±2℃ and RH≥95%, the influences of content and particle size of active aggregate, sort and content of alkali component and type of slag on the expansion ratios of alkali-activated slag cement(ASC) mortars due to alkali aggregate reaction(AAR) were studied. According to atomic absorption spectrometry,the amount of free alkali was measured in ASC mortars at 90d.The results show above factors affect AAR remarkably,but no dangerous AAR will occur in ASC system when the amount of active aggregate is below 15% and the mass fraction of alkali is not more than 5% (Na2O).Alkali participated in reaction as an independent component, and some hydrates containing alkali cations were produced, free alkalis in ASC system can be reduced enormously.Moreover,slag is an effective inhibitor, the possibility of generating dangerous AAR in ASC system is much lower at same conditions than that in ordinary Portland cement system.

  1. Natural Alkali Shifts to the Methanol Business

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Inner Mongolia Yuanxing Natural Alkali Co., Ltd. (Natural Alkali SZ: 000683) established in 1997 is a large chemical enterprise with new energy as its leading business and natural gas chemicals and natural alkali chemicals as the supplement business.

  2. Tris(bipyridineMetal(II-Templated Assemblies of 3D Alkali-Ruthenium Oxalate Coordination Frameworks: Crystal Structures, Characterization and Photocatalytic Activity in Water Reduction

    Directory of Open Access Journals (Sweden)

    Alla Dikhtiarenko

    2016-02-01

    Full Text Available A series of 3D oxalate-bridged ruthenium-based coordination polymers with the formula of {[ZII(bpy3][MIRu(C2O43]}n (ZII = Zn2+ (1, Cu2+ (3, 4, Ru2+ (5, 6, Os2+ (7, 8; MI = Li+, Na+; bpy = 2,2’-bipyridine and {[ZnII(bpy3](H2O[LiRu(C2O43]}n (2 has been synthesized at room temperature through a self-assembly reaction in aqueous media and characterized by single-crystal and powder X-ray diffraction, elemental analysis, infrared and diffuse reflectance UV–Vis spectroscopy and thermogravimetric analysis. The crystal structures of all compounds comprise chiral 3D honeycomb-like polymeric nets of the srs-type, which possess triangular anionic cages where [ZII(bpy3]2+ cationic templates are selectively embedded. Structural analysis reveals that the electronic configuration of the cationic guests is affected by electrostatic interaction with the anionic framework. Moreover, the MLCT bands gaps values for 1–8 can be tuned in a rational way by judicious choice of [ZII(bpy3]2+ guests. The 3D host-guest polymeric architectures can be used as self-supported heterogeneous photocatalysts for the reductive splitting of water, exhibiting photocatalytic activity for the evolution of H2 under UV light irradiation.

  3. Lead in K-Feldspar and Its Relations to Pb Metallogenesis

    Institute of Scientific and Technical Information of China (English)

    张乾; 刘志浩; 裘愉卓; 高计元; 王一先

    2003-01-01

    In intermediate-acid magmatic rocks, alkaline magmatic rocks, gneisses and migmatitic rocks K-feldspar is a rock-forming rock in which the contents of Pb are highest, just 2 -10 times those of the whole rock, 3 -16 times those of mica minerals and 6 -32 times those of quartz. The lowest contents of K-feldspar are recognized in Early Proterozoic and Achaean rocks, with Pb in the K-feldspar accounting for less than 10% of that in the whole rock; in postMiddle Proterozoic alkaline magmatic rocks, K-feldspar-rich granites and metamorphic rocks the contents of K-feldspar tend to increase, with the proportion of Pb over that in the whole rock being obviously increased. In the alkaline rocks in which K-feldspar accounts for 50% - 70% of the total in the whole rock, the contents of Pb in K-feldspar account approximately for 70% -95% of the total lead in the whole rock. Being accessible to hydrothermal alteration in the late periods, K-feldspar was conversed to sericite, calcite, quartz, etc. In the process of such conversion the lead would be leached out and then find its way into fluid phase. This kind of transformation can provide sufficient ore-forming material for later Pb metallogenesis.

  4. Full analysis of feldspar texture and crystal structure by combining X-ray and electron techniques

    DEFF Research Database (Denmark)

    Balic Zunic, Tonci; Piazolo, Sandra; Katerinopoulou, Anna;

    2013-01-01

    identification plus crystal structure refinement of all components in a feldspar intergrowth. This procedure was applied to perthitic intergrowths in feldspars from two different pegmatites in the Larvik plutonic complex in the southern part of the Oslo region, Norway. It revealed that the two starting high...

  5. The P-Fe diagram for K-feldspars: A preliminary approach in the discrimination of pegmatites

    Science.gov (United States)

    Sánchez-Muñoz, Luis; Müller, Axel; Andrés, Sol López; Martin, Robert F.; Modreski, Peter J.; de Moura, Odulio J. M.

    2017-02-01

    Pegmatites are extremely coarse-grained and heterogeneous rocks in which quantitative measurements of mineral proportions and chemical compositions of the whole rock are virtually impossible to acquire. Thus, conventional criteria such as bulk compositions and modal mineralogy used for the classifications of igneous rocks simply cannot be applied for pegmatites. An alternative is to use the mineralogical and chemical attributes of K-rich feldspars, the only mineral that is omnipresent in pegmatites. We have used this approach to test a possible discriminant among four groups of pegmatites on the basis of major petrological features, such as the abundance of quartz, feldspars, micas and phosphates. Group I is represented by relatively flux-poor, and silica-poor pegmatites, in most cases with hypersolvus feldspars, devoid of quartz and with minor biotite, which are common in rift settings as in the Coldwell Alkaline Complex in northwestern Ontario, Canada. Group II comprises relatively flux-poor, silica-rich pegmatites with quartz, subsolvus feldspars and biotite as major primary minerals, typically occurring in the asymmetric collisional Grenville Orogeny. Group III comprises relatively flux-rich, silica-rich P-poor pegmatites with quartz, subsolvus feldspars, and muscovite as the major primary minerals. Finally, group IV consists of relatively flux-rich, silica-rich, P-rich pegmatites with the same previous major minerals as in group III but with abundant phosphates. Group III and IV are found in most symmetric collisional orogens, such as in the Eastern Brazilian Pegmatite Province as the result of the collision of cratons mainly formed by igneous and metamorphic rock of Archean and Early Proterozoic age. We have selected specimens of blocky perthitic K-rich feldspar from the inner part of thirty-one pegmatites belonging to these four categories occurring worldwide to cover a wide range of mineralogy, geological age, geotectonic setting and geographical positions

  6. Dissolution rates and surface chemistry of feldspar glass and crystal. Final technical report, June 15, 1995 - August 14, 2001

    Energy Technology Data Exchange (ETDEWEB)

    Brantley, S.; Pantano, C.

    2002-06-11

    Final report summarizing the completed work of the project entitled 'Dissolution of Feldspar in the Field and Laboratory.' One of the highly debated questions today in low-temperature geochemical kinetics centers upon the rate and mechanism of dissolution of feldspar, the most common mineral in the crust. In this project, the mechanisms of feldspar dissolution were investigated by emphasizing experiments with feldspar glass and crystal while comparing surface and solution chemistry. Specifically, laboratory work focused on the structure of altered surface layers on feldspars, the rate of dissolution of feldspar crystal and glass, and the presence of porosity and surface coatings on feldspars. In a complementary field project, the use of Sr concentrations and isotopic ratios were used to calculate feldspar dissolution rates.

  7. Study of paramagnetic and luminescence centers of microcline feldspar

    Energy Technology Data Exchange (ETDEWEB)

    Tatumi, S.H. [Faculdade de Tecnologia de Sao Paulo, Praca Cel. Fernando Prestes, 30, 01124-060, Sao Paulo, SP (Brazil)]. E-mail: tatumi@fatecsp.br; Kinoshita, A. [Universidade do Sagrado Coracao, Rua Irma Arminda, 10-50, 17011-160, Bauru, Sao Paulo (Brazil); FFCLR-USP, Dep. Fisica e Matematica, Av. Bandeirantes, 3900, 14040-901, Ribeirao Preto, SP, Brasil (Brazil); Fukumoto, M.E. [Faculdade de Tecnologia de Sao Paulo, Praca Cel. Fernando Prestes, 30, 01124-060, Sao Paulo, SP (Brazil); Courriol, L.C. [Faculdade de Tecnologia de Sao Paulo, Praca Cel. Fernando Prestes, 30, 01124-060, Sao Paulo, SP (Brazil); Kassab, L.R.P. [Faculdade de Tecnologia de Sao Paulo, Praca Cel. Fernando Prestes, 30, 01124-060, Sao Paulo, SP (Brazil); Baffa, O. [FFCLR-USP, Dep. Fisica e Matematica, Av. Bandeirantes, 3900, 14040-901, Ribeirao Preto, SP (Brazil); Munita, C.S. [CNEN-IPEN/SP, Divisao de Radioquimica, c.p.11049- cep.05422.970, Sao Paulo, SP (Brazil)

    2005-02-01

    Microcline feldspar crystal has been analyzed in order to determine the centers suitable for use in ESR and luminescence dating. ESR measurements at RT showed the Fe{sup 3+} line, and at 77K the Si-O{sup -}..X signal with g=2.0052, 2.0098 and 2.0128. TL glow peak at 157 and 300 deg. C in UV interval were observed and in the VIS range we noted peaks at 150, 280 and 340 deg. C. TL growth curve of the 340 deg. C peak could be fitted by a saturating exponential equation and can be used in TL dating. Emission curves showed band widths 1.95+/-0.09, 2.73+/-0.08 and 4.94+/-0.50eV. Transitions from {sup 4}T{sub 1}->{sup 6}A{sub 1} of Fe{sup 3+} can be associated with the 1.95eV band and the transition from {sup 4}A{sub 1} {sup 4}E(G)->{sup 6}A{sub 1}(S) with 2.73eV band.

  8. Alkali metal and alkali earth metal gadolinium halide scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  9. Ultrahigh pressure (>7 GPa) gneissic K-feldspar (-bearing) garnet clinopyroxenite in the Altyn Tagh, NW China: Evidence from clinopyroxene exsolution in garnet

    Institute of Scientific and Technical Information of China (English)

    LIU; Liang; CHEN; Danling; ZHANG; Anda; SUN; Yong; WANG; Ya

    2005-01-01

    The exsolution of clinopyroxene and rutile in coarse-grain garnet is found in the gneissic K-feldspar(-bearing) garnet clinopyroxenite from Yinggelisayi in the Altyn Tagh, NW China. The maximum content of the exsolved clinopyroxene in the garnet is up to >5% by volume.The reconstructed precursor garnet (Grt1) before exsolution has a maximum Si content of 3.061 per formula uint, being of supersilicic or majoritic garnet. The peak-stage metamorphic pressure of >7 GPa is estimated using the geobarometer for volume percentage of exsolved pyroxene in garnet and the Si-(Al+Cr) geobarometer for majoritic garnet, and the temperature of about 1000℃ using the ternary alkali-feldspar geothermometer and the experimental data of ilmenite-magnetite solid solution. The protoliths of the rocks are intra-plate basic and intermediate igneous rocks, of which the geochemical features indicate that they are probably the products of the evolution of basic magma deriving from the continental lithosphere mantle. The rocks are in outcrops associated with ultrahigh pressure garnet-bearing Iherzolite and ultrahigh pressure garnet granitoid gneiss. All of these data suggest that the ultrahigh pressure metamorphic rocks in the Altyn Tagh are the products of deep-subduction of the continental crust, and such deepsubduction probably reaches to >200 km in depth. This may provide new evidence for further discussion of the dynamic mechanism of the formation and evolvement of the Altyn Tagh and the other collision orogenic belts in western China.

  10. Flexibility of experimental alumina/feldspar and SR ADORO dental composites.

    Science.gov (United States)

    Le Roux, A R; Lachman, N

    2010-03-01

    Flexure of a dental composite can be detrimental to the success of a restoration. Flexibility considerations are thus important when comparing dental materials to optimize the success of resin restorations. Flexibility of 5.6 x 18.0 x 2.0 mm3 experimental alumina/feldspar and SR ADORO dental composites specimens were compared. It was hypothesized that alumina/feldspar composites would be less flexible under a load than SR ADORO composites and that the flexibility would decrease significantly as the feldspar content was increased. Alumina was chemically sintered or bonded with 40%, 50% and 60% feldspar mass, silanized and infiltrated with urethane dimethacrylate (UDMA) to prepare the alumina/feldspar dental restorative composite specimens. Three point bending tests were performed in the Instron 44 machine for flexural comparison to SR ADORO. The alumina/feldspar specimens showed lower flexibility (mm displacement) than SR ADORO (p dental composites may provide added marginal seal benefit. However confirmation via in vivo function of alumina/feldspar dental composites is recommended.

  11. Optically stimulated phosphorescence in orthoclase feldspar over the millisecond to second time scale

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina; Jain, Mayank

    2010-01-01

    In the past, time-resolved IR stimulated luminescence (TR-IRSL) curves from feldspar have mainly been measured over a few hundred μs with the purpose of estimating the lifetimes of the components. In this study, we present the decay form of time-resolved IRSL and IR stimulated phosphorescence (IRSP......) from orthoclase feldspar covering over 8 orders of magnitude (50 ns to 7 s). A detailed characterisation of the slowly decaying signals (ms to s time scales) from feldspar is undertaken to obtain further insight into the role of re-trapping in both the IR stimulated luminescence (IRSL...

  12. Limits to depletion of blue-green light stimulated luminescence in feldspars: Implications for quartz dating

    DEFF Research Database (Denmark)

    Jain, M.; Singhvi, A.K.

    2001-01-01

    -red stimulation at elevated temperature (220 degreesC) (ETIR) permits depletions of charges in Type (A) and Type (B) to the extent that the feldspar BGSL can be reduced by up to 97% in 5 min. These results offer prospects for (1) improved precision in paleodose estimates based on quartz; (2) BGSL dating of quartz...... in a polyminerallic fine grain samples; (3) age estimates based on both quartz and feldspars from the same aliquots, and (4) dating based on feldspar micro-inclusions. (C) 2001 Elsevier Science Ltd. All rights reserved....

  13. Understanding the ice nucleation characteristics of feldspars suspended in solution

    Science.gov (United States)

    Kumar, Anand; Marcolli, Claudia; Kaufmann, Lukas; Krieger, Ulrich; Peter, Thomas

    2017-04-01

    Chemical) and 5 wt% lanolin (Fluka Chemical) is emulsified with a rotor-stator homogenizer for 40 s at a rotation frequency of 7000 rpm. 4 - 10 mg of this mixture is pipetted in an aluminum pan (closed hermetically), placed in the DSC and subjected to three freezing cycles. The first and the third freezing cycles are executed at a cooling rate of 10 K/min to control the stability of the sample. The second freezing cycle is executed at a 1 K/min cooling rate and is used for evaluation. Freezing temperatures are obtained by evaluating the onset of the freezing signal in the DSC curve and plotted against water activity. Results Based on Koop et al. (2000), a general decreasing trend in ice nucleation efficiency of the mineral samples with increasing solute concentrations is expected. Interestingly, feldspars (microcline, sanidine, plagioclase) in very dilute solutions of ammonia and ammonium salts (water activity close to one) show an increase in ice nucleation efficiency of 4 to 6 K compared to that in pure water. Similar trends but less pronounced are observed for kaolinite while quartz shows barely any effect. Therefore, there seem to be specific interactions between the feldspar surface and ammonia and/or ammonium ions which result in an increase in freezing temperatures at low solute concentrations. The surface ion exchange seems to be secondary for this effect since it is also present in ammonia solution. We hypothesize that ammonia adsorbs on the aluminol/silanol groups present on feldspar (viz. aluminosilicate surface) surfaces (Nash and Marshall, 1957; Belchinskaya et al., 2013). Hence allowing one of the N-H bonds to stick outwards from the surface, facing towards the bulk water and providing a favorable template for ice to grow. The current study gives an insight into the ice nucleation behavior of aluminosilicate minerals when present in conjunction with chemical species, eg. ammonium/sulfates, which is of high atmospheric relevance. References Koop et al., (2000

  14. Effect of Alkali Stress on Soluble Sugar, Antioxidant Enzymes and Yield of Oat

    Institute of Scientific and Technical Information of China (English)

    BAI Jian-hui; LIU Jing-hui; ZHANG Na; YANG Jun-heng; SA Ru-la; WU Lan

    2013-01-01

    Alkali stress can cause severe crop damage and reduce production. However, physiological processes involved in alkali stress in oat seedlings are not well understood. In this study, physiological responses and yield of oat to alkali stress were studied using the alkali-tolerant oat genotype Vao-9 and the alkali-sensitive oat genotype Baiyan 5. The results were:(i) low concentrations of alkali stress (25 and 50 mmol L-1) significantly reduced the yield and grain weight while increased the oat grain number per spike. A negative correlation between yield and malondialdehyde (MDA) content at the jointing and grain filling stages and positive correlations between yield on one hand and superoxide dismutase (SOD), and peroxidase (POD) activities on the other at the jointing stage were observed. There was a positive correlation between MDA and soluble sugar at the grain filling stage;(ii) soluble sugar content was increased at the jointing and grain filling stages and decreased at the heading stage by alkali stress;(iii) alkali stress increased the SOD activity during the heading and grain filling stages, and increased the POD activity at the heading stage. As compared to the control, the increase of MDA contents in alkali-treated oat was observed, during the jointing, heading and grain filling stages;(iv) under alkali stress, the oat genotype Vao-9 showed higher antioxidant enzyme activity and lower soluble sugar contents during the heading stage, and lower MDA contents than those in the oat genotype Baiyan 5 under alkali stress. The result suggested that the high ROS scavenging capacity and soluble sugar levels might play roles in oat response to alkali stress.

  15. Upgrading platform using alkali metals

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2017-01-17

    A method for removing sulfur, nitrogen or metals from an oil feedstock. The method involves reacting the oil feedstock with an alkali metal and a radical capping substance. The alkali metal reacts with the metal, sulfur or nitrogen content to form one or more inorganic products and the radical capping substance reacts with the carbon and hydrogen content to form a hydrocarbon phase. The inorganic products may then be separated out from the hydrocarbon phase.

  16. Upgrading platform using alkali metals

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2014-09-09

    A process for removing sulfur, nitrogen or metals from an oil feedstock (such as heavy oil, bitumen, shale oil, etc.) The method involves reacting the oil feedstock with an alkali metal and a radical capping substance. The alkali metal reacts with the metal, sulfur or nitrogen content to form one or more inorganic products and the radical capping substance reacts with the carbon and hydrogen content to form a hydrocarbon phase. The inorganic products may then be separated out from the hydrocarbon phase.

  17. Optimising the separation of quartz and feldspar optically stimulated luminescence using pulsed excitation

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina; Jain, Mayank; Thomsen, Kristina Jørkov;

    2010-01-01

    In luminescence dating, the two most commonly used natural minerals, quartz and feldspar, are exposed to different dose rates in the natural environment, and so record different doses. The luminescence signals also have different stabilities. For accurate dosimetry, the signals from these two...... minerals must be separated, either by physical separation of the mineral grains, or by instrumental separation of the luminescence signals. The luminescence signals from quartz and feldspar have different luminescence lifetimes under pulsed optical stimulation. This difference in lifetime can be used...... to discriminate between the two signals from a mixed quartz-feldspar sample. The purpose of this study is to identify optimum measurement conditions for the best separation of quartz OSL from that of feldspar in a mixed sample using pulsed stimulation and time-resolved OSL. We integrate the signal from 5 μs after...

  18. Scaling Properties of Feldspar and Quartz in Micro-images of Ideal Granites

    Institute of Scientific and Technical Information of China (English)

    Xu Deyi; Ke Xianzhong; Xie Shuyun; Cheng Qiuming

    2008-01-01

    The properties of feldspar and quartze are studied in this article from a fractal point of view using gray-scale micro-images of granite samples collected at the Fangshan (房山) granite body in Hebei (河北) Province, China, which can be regarded as an ideal granite in the sense of Vistelius. We found that there exist power-law relationships between the eigenvalues of the gray-scale matrices and their ranks for the feldspar and quartz. The fractal model used here is a λ-R model similar to the N-λ model proposed by Qiuming Cheng in 2005. Meanwhile, we found that average variances for the gray-scale matrices of feldspar are larger than those of quartz on the same sections, and this may be useful for auto-identification of feldspar and quartz as well as other minerals.

  19. Na-rich feldspar as a luminescence dosimeter in infrared stimulated luminescence (IRSL) dating

    DEFF Research Database (Denmark)

    Sohbati, Reza; Murray, Andrew; Jain, Mayank;

    2013-01-01

    on geological origin and erosion history, but the dosimetry of K-rich feldspar grains extracted from rocks is complicated because the internal dose rate is very dependent on the original feldspar grain size. The in situ grain size information is lost during the crushing process used to separate the grains...... are in agreement with the expected age control, raising the possibility that this signal originates mainly from K-rich feldspar contamination in our Na-rich fractions, and thus is not so useful in the luminescence dating of rock surfaces. On the other hand, the pIRIR290 fading-corrected ages based on the yellow......One of the challenges in dating rock surfaces is the choice of the luminescence mineral. Although quartz is the preferred dosimeter in sediment dating, it is often not sufficiently sensitive when extracted from solid rocks. The intensity of signals from feldspars tends to be much less dependent...

  20. Hydrothermal alteration of plagioclase and growth of secondary feldspar in the Hengill Volcanic Centre, SW Iceland

    Science.gov (United States)

    Larsson, D.; Grönvold, K.; Oskarsson, N.; Gunnlaugsson, E.

    2002-05-01

    Dissolution of igneous feldspar and the formation and occurrence of secondary feldspar in tholeiitic basalts from the Hengill volcanic centre, in SW Iceland was studied by microprobe analysis of cuttings from two ca. 2000 m deep geothermal wells. Well NG-7 in Nesjavellir represents a geothermal system in a rift zone where the intensity of young, insignificantly altered intrusions increases with depth. Well KhG-1 in Kolviðarhóll represents the margin of a rift zone where the intensity of intrusives is lower and the intensity of alteration higher. This marginal well represents altered basaltic crust in an early retrograde state. The secondary plagioclase in both wells is mainly oligoclase, occurring in association with K-feldspar and chlorite±actinolite. The texture of this assemblage depends on the lithology and intensity of alteration. In Nesjavellir (NG-7) the composition of secondary albite-oligoclase is correlated with the host-rock composition. This connection is not apparent in more intensely altered samples from Kolviðarhóll (KhG-1). The influence of temperature on composition of secondary Na-feldspar is unclear in both wells although Ca is expected to increase with temperature. Any temperature dependence may be suppressed by the influence of rock composition in Nesjavellir and by retrograde conditions at Kolviðarhóll. The absence of clear compositional gradients between igneous plagioclase and secondary feldspar and between Na-feldspar and K-feldspar suggests that secondary feldspars formed by dissolution precipitation reactions.

  1. Alkalis in Coal and Coal Cleaning Products / Alkalia W Węglu I Productach Jego Wzbogacania

    Science.gov (United States)

    Bytnar, Krzysztof; Burmistrz, Piotr

    2013-09-01

    In the coking process, the prevailing part of the alkalis contained in the coal charge goes to coke. The content of alkalis in coal (and also in coke) is determined mainly by the content of two elements: sodium and potasium. The presence of these elements in coal is connected with their occurrence in the mineral matter and moisture of coal. In the mineral matter and moisture of the coals used for the coke production determinable the content of sodium is 26.6 up to 62. per cent, whereas that of potassium is 37.1 up to 73.4 per cent of the total content of alkalis. Major carriers of alkalis are clay minerals. Occasionally alkalis are found in micas and feldspars. The fraction of alkalis contained in the moisture of the coal used for the production of coke in the total amount of alkalis contained there is 17.8 up to 62.0 per cent. The presence of sodium and potassium in the coal moisture is strictly connected with the presence of the chloride ions. The analysis of the water drained during process of the water-extracting from the flotoconcentrate showed that the Na to K mass ratio in the coal moisture is 20:1. Increased amount of the alkalis in the coal blends results in increased content of the alkalis in coke. This leads to the increase of the reactivity (CRI index), and to the decrease of strength (CSR index) determined with the Nippon Steel Co. method. W procesie koksowania przeważająca część zawartych we wsadzie węglowym alkaliów przechodzi do koksu. Zawartość alkaliów w węglu, a co za tym idzie i w koksie determinowana jest głównie zawartością dwóch pierwiastków: sodu i potasu. Obecność tych pierwiastków w węglu wiąże się z występowaniem ich w substancji mineralnej i wilgoci węgla. W substancji mineralnej oraz wilgoci węgli stosowanych do produkcji koksu, oznaczona zawartość sodu wynosi od 26.6 do 62.9%, a zawartość potasu od 37.1 do 73.4% alkaliów ogółem. Głównymi nośnikami alkaliów w substancji mineralnej są minera

  2. Alkali-rich intrusive rocks in the Qinghai-Xizang Plateau and its vicinities as exemplified by Kuganzi and Taihe plutons

    Institute of Scientific and Technical Information of China (English)

    张玉泉; 谢应雯

    1997-01-01

    The alkali-rich intrusive rocks in the Qinghai-Xizang Plateau can be divided into two series in terms of dark-colored rock-forming minerals, petrochemical composition and trace elements: i ) sodic alkaline series rocks consisting of alkaline rocks and alkali granite which contain dark-colored minerals, such as aegirine augite, aegirine and riebeckite, and being petrochemically enriched in alkali and sodium but low in Ca, Sr and Ba; ii ) potassic alkaline series rocks consisting of alkaline rocks and alkali granite which contain non-alkaline dark-colored minerals (diopside, edenite), and being petrochemically enriched in alkali, K and Ca with high abundances of Sr and Ba.

  3. Progressive deformation of feldspar recording low-barometry impact processes, Tenoumer impact structure, Mauritania

    Science.gov (United States)

    Jaret, Steven J.; Kah, Linda C.; Harris, R. Scott

    2014-06-01

    The Tenoumer impact structure is a small, well-preserved crater within Archean to Paleoproterozoic amphibolite, gneiss, and granite of the Reguibat Shield, north-central Mauritania. The structure is surrounded by a thin ejecta blanket of crystalline blocks (granitic gneiss, granite, and amphibolite) and impact-melt rocks. Evidence of shock metamorphism of quartz, most notably planar deformation features (PDFs), occurs exclusively in granitic clasts entrained within small bodies of polymict, glass-rich breccia. Impact-related deformation features in oligoclase and microcline grains, on the other hand, occur both within clasts in melt-breccia deposits, where they co-occur with quartz PDFs, and also within melt-free crystalline ejecta, in the absence of co-occurring quartz PDFs. Feldspar deformation features include multiple orientations of PDFs, enhanced optical relief of grain components, selective disordering of alternate twins, inclined lamellae within alternate twins, and combinations of these individual textures. The distribution of shock features in quartz and feldspar suggests that deformation textures within feldspar can record a wide range of average pressures, starting below that required for shock deformation of quartz. We suggest that experimental analysis of feldspar behavior, combined with detailed mapping of shock metamorphism of feldspar in natural systems, may provide critical data to constrain energy dissipation within impact regimes that experienced low average shock pressures.

  4. Asbestos contamination in feldspar extraction sites: a failure of prevention? Commentary.

    Science.gov (United States)

    Cavariani, Fulvio

    2016-01-01

    Fibrous tremolite is a mineral species belonging to the amphibole group. It is present almost everywhere in the world as a natural contaminant of other minerals, like talc and vermiculite. It can be also found as a natural contaminant of the chrysotile form of asbestos. Tremolite asbestos exposures result in respiratory health consequences similar to the other forms of asbestos exposure, including lung cancer and mesothelioma. Although abundantly distributed on the earth's surface, tremolite is only rarely present in significant deposits and it has had little commercial use. Significant presence of amphibole asbestos fibers, characterized as tremolite, was identified in mineral powders coming from the milling of feldspar rocks extracted from a Sardinian mining site (Italy). This evidence raises several problems, in particular the prevention of carcinogenic risks for the workers. Feldspar is widespread all over the world and every year it is produced in large quantities and it is used for several productive processes in many manufacturing industries (over 21 million tons of feldspar mined and marketed every year). Until now the presence of tremolite asbestos in feldspar has not been described, nor has the possibility of such a health hazard for workers involved in mining, milling and handling of rocks from feldspar ores been appreciated. Therefore the need for a wider dissemination of knowledge of these problems among professionals, in particular mineralogists and industrial hygienists, must be emphasized. In fact both disciplines are necessary to plan appropriate environmental controls and adequate protections in order to achieve safe working conditions.

  5. Process for recovering alkali metals and sulfur from alkali metal sulfides and polysulfides

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard; Alvare, Javier

    2016-10-25

    Alkali metals and sulfur may be recovered from alkali monosulfide and polysulfides in an electrolytic process that utilizes an electrolytic cell having an alkali ion conductive membrane. An anolyte solution includes an alkali monosulfide, an alkali polysulfide, or a mixture thereof and a solvent that dissolves elemental sulfur. A catholyte includes molten alkali metal. Applying an electric current oxidizes sulfide and polysulfide in the anolyte compartment, causes alkali metal ions to pass through the alkali ion conductive membrane to the catholyte compartment, and reduces the alkali metal ions in the catholyte compartment. Liquid sulfur separates from the anolyte solution and may be recovered. The electrolytic cell is operated at a temperature where the formed alkali metal and sulfur are molten.

  6. Alkali binding in hydrated Portland cement paste

    NARCIS (Netherlands)

    Chen, W.; Brouwers, H.J.H.

    2010-01-01

    The alkali-binding capacity of C–S–H in hydrated Portland cement pastes is addressed in this study. The amount of bound alkalis in C–S–H is computed based on the alkali partition theories firstly proposed by Taylor (1987) and later further developed by Brouwers and Van Eijk (2003). Experimental data

  7. A negative ion source for alkali ions

    NARCIS (Netherlands)

    Vermeer, A.; Zwol, N.A. van

    1980-01-01

    An ion source is described which delivers negative alkali ions. With this source, which consists of a duoplasmatron and a charge exchange canal with alkali vapour, negative Li, Na and K ions are produced. The oven in which alkali metals are evaporated can reach temperatures up to 575°C.

  8. A negative ion source for alkali ions

    NARCIS (Netherlands)

    Vermeer, A.; Zwol, N.A. van

    1980-01-01

    An ion source is described which delivers negative alkali ions. With this source, which consists of a duoplasmatron and a charge exchange canal with alkali vapour, negative Li, Na and K ions are produced. The oven in which alkali metals are evaporated can reach temperatures up to 575°C.

  9. Laboratory fading rates of various luminescence signals from feldspar-rich sediment extracts

    DEFF Research Database (Denmark)

    Thomsen, Kristina Jørkov; Murray, A.S.; Jain, Mayank;

    2008-01-01

    ) and optically stimulated luminescence (OSL) signals exhibit anomalous (athermal) fading. Much of the OSL work carried out on feldspars in recent years has focussed on determining fading rates and correcting for them. Almost all work has been carried out using IR stimulation at 50 degrees C detected in the blue...... region of the spectrum. In contrast, we have determined fading rates for various sedimentary feldspar samples using different stimulation and detection windows. If the initial part of the OSL signal is used the lowest fading rate is observed with post-IR blue stimulation (UV detection), but if a later...... part of the signal is used the lowest fading rate is obtained for IR stimulation (blue detection). Daylight bleaching experiments show that, unlike quartz, the initial and final parts of the feldspar OSL signal bleach at approximately the same rate. Stimulation at elevated temperatures significantly...

  10. Active sites in heterogeneous ice nucleation—the example of K-rich feldspars

    Science.gov (United States)

    Kiselev, Alexei; Bachmann, Felix; Pedevilla, Philipp; Cox, Stephen J.; Michaelides, Angelos; Gerthsen, Dagmar; Leisner, Thomas

    2017-01-01

    Ice formation on aerosol particles is a process of crucial importance to Earth’s climate and the environmental sciences, but it is not understood at the molecular level. This is partly because the nature of active sites, local surface features where ice growth commences, is still unclear. Here we report direct electron-microscopic observations of deposition growth of aligned ice crystals on feldspar, an atmospherically important component of mineral dust. Our molecular-scale computer simulations indicate that this alignment arises from the preferential nucleation of prismatic crystal planes of ice on high-energy (100) surface planes of feldspar. The microscopic patches of (100) surface, exposed at surface defects such as steps, cracks, and cavities, are thought to be responsible for the high ice nucleation efficacy of potassium (K)-feldspar particles.

  11. Iron removal on feldspar by using Averrhoa bilimbii as bioleaching agent

    Science.gov (United States)

    Amin, Muhammad; Aji, Bramantyo B.; Supriyatna, Yayat Iman; Bahfie, Fathan

    2017-01-01

    Investigation of Averrhoa bilimbii as bioleaching agent was carried out. Parameters of leaching duration, acid concentration, and temperature were performed in iron removal process. Feldspar with sized 149 µm was diluted in 30 ml acid solution in order to reduce its iron content. The experimental results showed a good technical feasibility of the process which iron oxide content of feldspar was decreased from 2.24% to 0.29%. The lowest iron concentration remained was obtained after 5 hours of leaching treatment at 60 °C, and concentrated (100 vol%) Averrhoa bilimbii extract as bioleaching agent. SEM characterizations were carried out on the feldspar before and after the leaching treatment. The result shows that there were no significant effect of leaching process on the ore morphology.

  12. Raman Spectroscopic Characterization of the Feldspars: Implications for Surface Mineral Characterization in Planetary Exploration

    Science.gov (United States)

    Freeman, J. J.; Wang, Alian; Kuebler, K. E.; Haskin, L. A.

    2003-01-01

    The availability in the last decade of improved Raman instrumentation using small, stable, intense lasers, sensitive CCD array detectors, and advanced fast grating systems enabled us to develop the Mars Microbeam Raman Spectrometer (MMRS), a field-portable Raman spectrometer with precision and accuracy capable of identifying minerals and their different compositions. For example, we can determine Mg cation ratios in pyroxenes and olivines to +/-0.1 on the basis of Raman peak positions. Feldspar is another major mineral formed in igneous systems whose characterization is important for determining rock petrogenesis and alteration. From their Raman spectral pattern, feldspars can be readily distinguished from ortho- and chain-silicates and from other tecto-silicates such as quartz and zeolites. We show here how well Raman spectral analysis can distinguish among members within the feldspar group.

  13. Identifying well-bleached quartz using the different bleaching rates of quartz and feldspar luminescence signals

    DEFF Research Database (Denmark)

    Murray, A.S.; Thomsen, Kristina Jørkov; Masuda, N.;

    2012-01-01

    When dating older sedimentary deposits using quartz, there are no unambiguous methods for identifying the presence of incomplete bleaching. Current statistical analysis of dose distributions depends entirely on the assumption that incomplete bleaching and mixing are the main causes of any excess...... in relative bleaching rates of quartz optically stimulated luminescence (OSL) and feldspar luminescence stimulated at 50 °C by infrared light (IR50) and feldspar luminescence stimulated at 290 °C by infrared light after a stimulation at 50 °C (pIRIR290), and use recently deposited samples to determine...... that the large aliquot data are more likely to be correct. We conclude that a comparison of quartz and feldspar doses provides a useful independent method for identifying well-bleached quartz samples, and that it is unwise to apply statistical models to dose distributions without clear evidence for the physical...

  14. Salinity-Dependent Adhesion Response Properties of Aluminosilicate (K-Feldspar) Surfaces

    DEFF Research Database (Denmark)

    Lorenz, Bärbel; Ceccato, Marcel; Andersson, Martin Peter

    2017-01-01

    Flooding sandstone oil reservoirs with low salinity water can lead to a significant increase in oil recovery, a phenomenon called "the low salinity effect". Although there are many factors that contribute to this response, the surface tension on the pore walls is an important one. Sandstone...... is composed predominantly of quartz with some clay, but feldspar grains are often also present. While the wettability of quartz and clay surfaces has been thoroughly investigated, little is known about the adhesion properties of feldspar. We explored the interaction of model oil compounds, molecules...... in well sorted sandstone. Adhesion forces, measured with the chemical force mapping (CFM) mode of atomic force microscopy (AFM), showed a low salinity effect on the fresh feldspar surfaces. Adhesion force, measured with -COO(H)-functionalized tips, was 60% lower in artificial low salinity seawater (LS...

  15. Application of pulsed OSL to the separation of the luminescence components from a mixed quartz/feldspar sample

    DEFF Research Database (Denmark)

    Denby, Phil M.; Bøtter-Jensen, L.; Murray, A.S.

    2006-01-01

    this stimulation source, and hi.-h-speed photon timing, the OSL yield can be monitored throughout the pulsing cycle and subsequent OSL decay. It is found that the total photon yield per unit stimulation power in pulsed mode is, for quartz, twice and, for feldspar, nearly four times, that in continuous wave mode......It is known that the pulsed optically stimulated luminescence (OSL) characteristics of quartz and feldspars are very different. These differences can be used to preferentially discriminate against the feldspar signal in mixed quartz\\feldspar mineral assemblages, or in separated quartz contaminated...

  16. Extraction of potassium from K-feldspar via the CaCl2 calcination route☆

    Institute of Scientific and Technical Information of China (English)

    Bo Yuan; Chun Li; Bin Liang; Li Lü; Hairong Yue; Haoyi Sheng; Longpo Ye; Heping Xie

    2015-01-01

    The extraction of potassium from K-feldspar via a calcium chloride calcination route was studied with a focus on the effects of the calcination atmosphere, calcination temperature and time, mass ratio of CaCl2 to K-feldspar ore and particle size of the K-feldspar ore. The results demonstrated that a competing high-temperature hydrolysis reaction of calcium chloride with moisture in a damp atmosphere occurred concurrently with the conversion reaction of K-feldspar with CaCl2, thus reducing the amount of potassium extracted. The conversion reaction started at approximately 600 °C and accelerated with increasing temperature. When the temperature rose above 900 °C, the extraction of potassium gradually decreased due to the volatilization of the product, KCl. As much as approximately 41%of the potassium was volatilized in 40 min at 1100 °C. The mass ratio of CaCl2/K-feldspar ore significantly affected the extraction. At a mass ratio of 1.15 and 900 °C, the potassium extraction reached 91%in 40 min, while the extraction was reduced to only 22%at the theoretical mass ratio of 0.2. Optimal process conditions are as follows:ore particle size of 50–75μm, tablet forming pressure of 3 MPa, dry nitrogen atmosphere, mass ratio of CaCl2/ore 1.15:1, calcination temperature of 900 °C, and calcination time of 40 min. The XRD analysis revealed that a complex phase transition of the product SiO2 was also accompanied by the con-version reaction of K-feldspar/CaCl2. The SiO2 product formed at the initial stage was in the quartz phase at 900 °C and was gradually transformed into cristobalite after 30 min.

  17. Regional and local correlations of feldspar geochemistry of the Peach Spring Tuff, Alvord Mountain, California

    Science.gov (United States)

    Buesch, David C.

    2016-01-01

    The chemical composition of feldspar grains in an ignimbrite from the Spanish Canyon Formation in the Alvord Mountain area, California, have been used to confirm similarities in three measured sections locally, and they are similar to exposures of the Peach Spring Tuff (PST) regionally. Feldspar grains were identified on the basis of texture (zoning, as mantled feldspars, or in crystal clusters), whether the grains were attached to glass or were in pumice clasts, or were simply crystal fragments with no textural context. Chemistry was determined by electron microprobe analysis, and each analysis is calculated in terms of the percent endmember and plotted on orthoclase (Or) versus anorthite (An) plots. In general, the PST has sanidine and plagioclase compositions that are consistent with having formed in high-silica rhyolite and trachyte within a zoned magma chamber. Feldspars from the PST in Spanish Canyon area cluster along the rhyolitic trend with no grains along the trachytic trend. Similar clustering of feldspars along the rhyolitic trend with no grains along the trachytic trend also occur in the PST from Granite Spring and Providence Mountains to the east of the Alvord Mountain area, and the ranges in compositions are also similar in these locations. In contrast, the PST in the Kane Wash area of the Newberry Mountains has feldspars only from the rhyolitic trend in the basal deposits, but some grains from the trachytic trend are in the upper part of the deposit, and the range in compositions are greater than in the Spanish Canyon area. The variations in vertical compositional zoning and compositional range in these different deposits suggests there were probably different flow paths (or timing of the delivery) during the eruption and runout of the pyroclastic flow(s) generated from the climactic eruption of the PST magma chamber.

  18. Rubidium-rich feldspars and associated minerals from the Luolamäki pegmatite, Somero, Finland

    Directory of Open Access Journals (Sweden)

    Teerstra, D.K.

    1998-12-01

    Full Text Available Rubidium feldspar occurs near the core zone of the highly fractionated petalite-subtype Luolamäki granitic pegmatite in intimate intergrowth with other feldspars which are part of a characteristic sequence of alteration of pollucite. Pods of pollucite are cut by 5-20 cm-wide veins of albite, petalite, non-perthitic microcline, lepidolite and quartz, by thinner veins of fine-grained micas and spodumene, and are replaced by metasomatic adularia. Grains of rubidium feldspar occur as a potentially ordered phase in the vein microcline in association with earlier-exsolved albite, and also as late thin (< 5 μm veinlets. Rubidium feldspar also occurs as a potentially disordered phase which crystallized along with metasomatic adularia. Both generations of (Rb,K-feldspar have a similar compositional range, close to the join KAlSi3O8-RbAlSi3O8, typically with up to ~21 wt.% Rb2O (~70 mol.% Rbf and with minor Cs, but neglible Na, Ca, Fe or P. Extreme compositions have 26.0 wt.% Rb2O (89.0 mol.% Rbf and 1.26 wt.% Cs2O (2.8 mol.% Csf. The diffuse compositional gradients from microcline to rubicline are consistent with a solid-state exsolution origin, followed by fluid-assisted textural coarsening which generates distinct phase boundaries. In contrast, metasomatic adularian (Rb,K-feldspar was precipitated at low temperature (250-150°C and fine-scale zoning with variable K/Rb is preserved as a growth feature.

  19. Dependence of (anomalous) fading of infra-red stimulated luminescence on trap occupancy in feldspars

    DEFF Research Database (Denmark)

    Morthekai, P.; Jain, Mayank; Gach, Grzegorz

    2013-01-01

    Dose dependency of anomalous fading of infra-red stimulated luminescence (IRSL) from feldspars has been investigated using radiations of different ionisation qualities. The rate of fading of the IRSL signal after proton irradiation (9.4–30%/decade) is on an average almost twice compared to that a......Dose dependency of anomalous fading of infra-red stimulated luminescence (IRSL) from feldspars has been investigated using radiations of different ionisation qualities. The rate of fading of the IRSL signal after proton irradiation (9.4–30%/decade) is on an average almost twice compared...

  20. Influence of crystal structure on the optically stimulated luminescence properties of feldspars

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Bøtter-Jensen, L.; Ypma, P.J.M.

    1994-01-01

    Work is presented showing that the crystal structure of feldspar plays an important role in determining the energy positions at which optically stimulated luminescence transitions can occur, their thermo-optical behavior, the transport properties of charge in the conduction and valence bands, and......, and the time decay characteristics of the luminescence. First-order calculations of these effects are presented, and comparison is made with experimental results.......Work is presented showing that the crystal structure of feldspar plays an important role in determining the energy positions at which optically stimulated luminescence transitions can occur, their thermo-optical behavior, the transport properties of charge in the conduction and valence bands...

  1. On the trap depth of the IR-sensitive trap in Na- and K-feldspar

    DEFF Research Database (Denmark)

    Kars, Romée H.; Poolton, Nigel R.J.; Jain, Mayank;

    2013-01-01

    Feldspars are natural radiation dosimeters used in geological dating. The processes that underlie the measured natural- and laboratory induced infrared stimulated luminescence (IRSL) signals are, however, not fully understood. In this study we aim to determine the optical depth of the electron trap......, the trap depth is tentatively estimated to be ∼2.1 and ∼2.5 eV for Na- and K-feldspar, respectively. The fast phosphorescence following IRSL in both crystals is likely the result of tunnelling from bandtail states in the vicinity of the excited state of the IR-trap. The post-OSL phosphorescence decay...

  2. Red-IR stimulated luminescence in K-feldspar: Single or multiple trap origin?

    Science.gov (United States)

    Thalbitzer Andersen, Martin; Jain, Mayank; Tidemand-Lichtenberg, Peter

    2012-08-01

    We investigate on the origins of the infra-red stimulated luminescence (IRSL) signals in 3 potassium feldspars based on IR-red spectroscopy (˜700-1050 nm) using a fiber-coupled tunable Ti:Sapphire laser, in combination with different thermal and optical (pre)treatments of the samples. We also measure dose-response curves with different wavelengths and at different stimulation temperatures so as to be able to distinguish between traps based on their electron trapping cross-sections. Our data suggest that the dosimetric signals, IRSL, and the post IR-IRSL in K-feldspars arise from a single electron trapping centre.

  3. Luminescence dating of young coastal deposits from New Zealand using feldspar

    DEFF Research Database (Denmark)

    Madsen, Anni T.; Buylaert, Jan-Pieter; Murray, Andrew S.

    2011-01-01

    A new measurement protocol has been tested on K-feldspars from Whanganui Inlet and Parengarenga Harbour, New Zealand. A Single Aliquot Regenerative (SAR) dose protocol, using two successive infrared (IR) stimulations (post-IR IR SAR protocol) is setup for these young (......A new measurement protocol has been tested on K-feldspars from Whanganui Inlet and Parengarenga Harbour, New Zealand. A Single Aliquot Regenerative (SAR) dose protocol, using two successive infrared (IR) stimulations (post-IR IR SAR protocol) is setup for these young (...

  4. On the shape of continuous wave infrared stimulated luminescence signals from feldspars: A case study

    DEFF Research Database (Denmark)

    Pagonis, V.; Jain, Mayank; Thomsen, Kristina Jørkov

    2014-01-01

    to guide future modeling work on luminescence processes in feldspars. Small statistical differences were found between K-rich and Na-rich fractions of the same sample. However, the experimental data shows that the parameters depend on the irradiation dose, but do not depend on the time elapsed after...

  5. Red-IR stimulated luminescence in K-feldspar: Single or multiple trap origin?

    DEFF Research Database (Denmark)

    Andersen, Martin Thalbitzer; Jain, Mayank; Tidemand-Lichtenberg, Peter

    2012-01-01

    We investigate on the origins of the infra-red stimulated luminescence (IRSL) signals in 3 potassium feldspars based on IR-red spectroscopy (700–1050 nm) using a fiber-coupled tunable Ti:Sapphire laser, in combination with different thermal and optical (pre)treatments of the samples. We also...

  6. Testing the application of quartz and feldspar luminescence dating to MIS 5 Japanese marine deposits

    DEFF Research Database (Denmark)

    Thiel, Christine; Tsukamoto, Sumiko; Tokuyasu, Kayoko

    2015-01-01

    The applicability of both quartz and feldspar luminescence dating was tested on twenty-five samples from a marine succession now forming a coastal cliff at Oga Peninsula, Honshu Island, Japan. The quartz optically stimulated luminescence (OSL) signal shows thermal instability and linear modulated...

  7. Determination of Potassium in Feldspars by Beta Counting Using a GM Multicounter System

    DEFF Research Database (Denmark)

    Bøtter-Jensen, Lars; Mejdahl, V.

    1985-01-01

    A gas flow multicounter system developed at Riso National Laboratory for low-level beta counting applications was adopted for measuring potassium in feldspars extracted from archaeological and geological materials, in connection with TL dating work. A guard counter reduces the background by using...

  8. Light scattering by small feldspar particles simulated using the Gaussian random sphere geometry

    NARCIS (Netherlands)

    Veihelmann, B.; Nousiainen, T.; Kahnert, M.; Zande, W.J. van der

    2006-01-01

    The single-scattering properties of Gaussian random spheres are calculated using the discrete dipole approximation. The ensemble of model particles is assumed to be representative for a feldspar dust sample that is characteristic for weakly absorbing irregularly shaped mineral aerosol. The morpholog

  9. Development and characterization of parian bodies using feldspar from two selected deposits

    Directory of Open Access Journals (Sweden)

    Toluwalope OGUNDARE

    2016-07-01

    Full Text Available Self glazed bodies also called Parian Bodies are chiefly composed of Feldspar which majorly acts as flux in reducing the melting temperature of the particular ceramic body thereby reducing the stress of double firing a ceramic product. In this present research work, Okpella and Ijero-Ekiti feldspar deposits in Nigeria together with other raw materials were utilized to develop parian bodies which are very suitable for making ceramic tiles, dolls and figurines. Chemical analyses were carried out on the raw materials using X-ray fluorescence (XRF in order to ascertain their suitability for developing parian bodies. Six compositions were made from these two deposits using a standard parian body composition of 70% feldspar. The samples were shaped, dried and sintered between 1050°C -1250°C at the interval of 50°C. Flexural strength, fired shrinkage, porosity and water absorption tests were used to characterize the samples. The results showed that samples fired at 1200°C and 1250°C exhibited technological properties that meet up with ISO standards. The two feldspar deposits were found to be suitable for developing parian bodies

  10. Measurement of the dose in quartz in the presence of feldspar contamination

    DEFF Research Database (Denmark)

    Wallinga, J.; Murray, A.S.; Bøtter-Jensen, L.

    2002-01-01

    , without seriously affecting the quartz OSL signal. A single-aliquot regenerative-dose protocol is proposed which, in our samples, allows accurate measurement of the dose in quartz in the presence of feldspar contamination. The protocol also has potential use for quartz dose determination in mixed...

  11. SCR neon and argon in Kapoeta feldspar: Evidence for an active ancient Sun

    Science.gov (United States)

    Rao, M. N.; Garrison, D. H.; Bogard, D. D.

    1993-01-01

    From etched feldspar size-fractions of Kapoeta, we determine a significant excess of cosmogenic Ne-21 and Ar-38 over that produced by galactic cosmic rays. This excess component is attributed to early production by energetic solar protons and suggest that the energetic proton flux from the ancient Sun was several hundred times more intense than that of the contemporary Sun.

  12. Positron-alkali atom scattering

    Science.gov (United States)

    Mceachran, R. P.; Horbatsch, M.; Stauffer, A. D.; Ward, S. J.

    1990-01-01

    Positron-alkali atom scattering was recently investigated both theoretically and experimentally in the energy range from a few eV up to 100 eV. On the theoretical side calculations of the integrated elastic and excitation cross sections as well as total cross sections for Li, Na and K were based upon either the close-coupling method or the modified Glauber approximation. These theoretical results are in good agreement with experimental measurements of the total cross section for both Na and K. Resonance structures were also found in the L = 0, 1 and 2 partial waves for positron scattering from the alkalis. The structure of these resonances appears to be quite complex and, as expected, they occur in conjunction with the atomic excitation thresholds. Currently both theoretical and experimental work is in progress on positron-Rb scattering in the same energy range.

  13. Beneficiation of feldspar ore for application in the ceramic industry: Influence of composition on the physical characteristics

    Directory of Open Access Journals (Sweden)

    M.E. Gaied

    2015-03-01

    Experimental studies indicate that an acceptable concentrate for industrial application can be obtained from these rocks. The feldspar yield was used to evaluate the process efficiency. Besides, the cone shrinkage, water absorption, degree of vitrification, mechanical properties (flexural strength and dielectric behaviour were used to monitor the quality of the recovered feldspars.

  14. Luminescence at the end of the tunnelling - Investigating charge transfer mechanisms and luminescence dating methods for feldspar minerals

    NARCIS (Netherlands)

    Kars, R.H.

    2014-01-01

    This thesis comprises analyses of mineral physics with an application in geology and archeology. The thesis contributes to the development of feldspar luminescence dating methods in order to extend the applicable age range of feldspar luminescence dating in the Quaternary (last 2.6 Ma). The research

  15. The role of the alkali and chalcogen atoms on the stability of the layered chalcogenide \\mathbf{{{A}_{2}}{{M}^{II}}M_{3}^{\\,IV}{{Q}_{8}}} (A  =  alkali-metal M  =  metal-cations Q  =  chalcogen) compounds: a density functional theory investigation within van der Waals corrections

    Science.gov (United States)

    Besse, Rafael; Da Silva, Juarez L. F.

    2017-01-01

    There is a great interest to design two-dimensional (2D) chalcogenide materials, however, our atomistic understanding of the major physical parameters that drive the formation of 2D or three-dimensional (3D) chalcogenides is far from satisfactory, in particular, for complex quaternary systems. To address this problem, we selected a set of quaternary 2D and 3D chalcogenide compounds, namely, {{\\text{A}}2}\\text{ZnS}{{\\text{n}}3}{{\\text{Q}}8} (A  =  Li, K, Cs; Q  =  S, Se, Te), which were investigated by density functional theory calculations within van der Waals (vdW) corrections. Employing experimental crystal structures and well designed crystal modifications, we found that the average atomic radius of the alkali-metal, A, and chalcogen, Q, species play a crucial role in the stability of the 2D structures. For example, the 2D structures are energetically favored for smaller (R1.8~{\\mathring{\\text{A}}}) average atomic radius, while 3D structures are favored at intermediate average atomic radius. Those results are explained in terms of strain minimization and Coulomb repulsion of the anionic species in the structure framework. Furthermore, the equilibrium lattice parameters are in excellent agreement with experimental results. Thus, the present insights can help in the design of stable quartenary 2D chalcogenide compounds.

  16. Performance characterization of rigid polyurethane foam with refined alkali lignin and modified alkali lignin

    Institute of Scientific and Technical Information of China (English)

    LIU Zhi-ming; YU Fei; FANG Gui-zhen; YANG Hui-jun

    2009-01-01

    The two kinds of rigid polyurethane (PU) foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.

  17. Authigenic K-feldspar in salt rock (Haselgebirge Formation, Eastern Alps)

    Science.gov (United States)

    Leitner, Christoph

    2015-04-01

    The crystallisation of authigenic quartz under low temperature, saline conditions is well known (Grimm, 1962). Also the growth of low temperature authigenic feldspar in sediments is a long known phenomenon (Kastner & Siever, 1979; Sandler et al., 2004). In this study we intend to show that halite (NaCl) is a major catalyser for authigenic mineral growth. During late Permian (c. 255-250 Ma), when the later Eastern Alps were located around north of the equator, the evaporites of the Haselgebirge Formation were deposited (Piller et al., 2004). The Haselgebirge Fm. consists in salt mines of a two-component tectonite of c. 50 % halite and 50 % sedimentary clastic and other evaporite rocks (Spötl 1998). Most of the clastic rocks are mud- to siltstones ("mudrock"). During this study, we investigated rare sandstones embedded in salt rock form four Alpine salt mines. Around 40 polished thin sections were prepared by dry grinding for thin section analysis and scanning electron microscopy. The sandstones consist mainly of quartz, K-feldspar, rock fragments, micas, accessory minerals and halite in the pore space. They are fine grained and well sorted. Mudrock clasts in sandstone were observed locally, and also coal was observed repeatedly. Asymmetric ripples were found only in the dimension of millimeters to centimeters. Euhedral halite crystals in pores indicate an early presence of halite. During early diagenesis, authigenic minerals crystallized in the following chronological order. (1) Where carbonate (mainly magnesite) occurred, it first filled the pore space. Plant remains were impregnated with carbonate. (2) Halite precipitated between the detritic sandstone grains. Carbonate grains can be completely embedded in halite. (3) K-feldspar and quartz grains usually expose a detritic core and a later grown euhedral inclusion free rim. Euhedral rims of K-feldspar often also enclose a halite core. K-feldspar replaced the pre-existing halite along former grain boundaries of

  18. Influence of mesostasis in volcanic rocks on the alkali-aggregate reaction

    KAUST Repository

    Tiecher, Francieli

    2012-11-01

    Mesostasis material present in the interstices of volcanic rocks is the main cause of the alkali-aggregate reaction (AAR) in concretes made with these rock aggregates. Mesostasis often is referred to as volcanic glass, because it has amorphous features when analyzed by optical microscopy. However, this study demonstrates that mesostasis in the interstitials of volcanic rocks most often consists of micro to cryptocrystalline mineral phases of quartz, feldspars, and clays. Mesostasis has been identified as having different characteristics, and, thus, this new characterization calls for a re-evaluation of their influence on the reactivity of the volcanic rocks. The main purpose of this study is to correlate the characteristics of mesostasis with the AAR in mortar bars containing basalts and rhyolites. © 2012 Elsevier Ltd. All rights reserved.

  19. Flotation Separation Research of Quartz and Feldspar%石英和长石的浮选分离试验研究

    Institute of Scientific and Technical Information of China (English)

    龚豪; 王永田; 贾凯; 李兴平

    2013-01-01

    采用3种常用硅砂选矿工艺流程对石英砂进行试验研究,并对3种工艺的机理进行了分析.结果表明,氢氟酸法较无氟浮选法和碱法浮选法分选效果好,采用氢氟酸法获得了石英产率67.85%、Al2O3含量1.02%、Fe2O3含量0.068%的技术指标,长石和石英得到了较好的分离.%Three common separation processes for the quartz sand are studied in the paper and their mechanisms are discussed.The results show that the hydrofluoric acid method can achieve much better performance than non-fluoride with acid method and alkali method,adopted the process of the hydrofluoric acid method,got the quartz concentrate with a yield of 67.85%,Al2O3 content of 1.02%,Fe2O3 content of 0.068%,quartz and feldspar can be effectively separated.

  20. A robust feldspar luminescence dating method for Middle and Late Pleistocene sediments

    DEFF Research Database (Denmark)

    Buylaert, Jan-Pieter; Jain, Mayank; Murray, Andrew S.

    2012-01-01

    Luminescence dating is used extensively to provide absolute chronologies for Late Pleistocene sediments. Nowadays, most optical dates are based on quartz optically stimulated luminescence (OSL). However, the application of this signal is usually limited to the last ~100 ka because of saturation...... of the quartz luminescence signal with dose. In contrast, the feldspar infrared stimulated luminescence (IRSL) dose–response curve grows to much higher doses; this has the potential to extend the datable age range by a factor of 4–5 compared with quartz OSL. However, it has been known for several decades...... is widely applicable (feldspar of appropriate luminescence behaviour is even more ubiquitous than quartz). These characteristics make this a method of great importance for the dating of Middle and Late Pleistocene deposits....

  1. Understanding optically stimulated charge movement in quartz and feldspar using time-resolved measurements

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina

    to identify various charge transport mechanisms in the different time regimes. The techniques employed are time-resolved OSL, continuous-wave OSL, TL, optically stimulated exo-electron (OSE) emission and time-resolved OSE. These different techniques are used in combination with variable thermal or optical...... and the conduction band in determining charge transport. It is suggested that unlike quartz, the excited state lifetime does not play an important role in our measurements. Finally, it is shown that one of these routes favors production if a least fading signal (due to quantum mechanical tunnelling) in feldspars...... the TR-OSL and optically stimulated phosphorescence signals from quartz and feldspars spanning several orders of magnitude in time (few ns to the seconds time scale) in order to identify various charge transport mechanisms in the different time regimes. The techniques employed are time-resolved OSL...

  2. Further investigations into pulsed optically stimulated luminescence from feldspars using blue and green light

    DEFF Research Database (Denmark)

    Ankjærgaard, Christina; Jain, Mayank; Kalchgruber, R.

    2009-01-01

    The purpose of this paper is to investigate characteristics of luminescence signals resulting from pulsed optical stimulation of feldspars and thereby to understand the underlying processes giving rise to the signal. Fourteen different feldspar specimens were investigated using time...... suggests that the TR-OSL signal decay is governed by the recombination process and not by the excited state lifetime. Furthermore data from the TR-OSL signal dependence on stimulation time and preheat temperature suggest that the recombination process may not be a sum of exponentials, although the model......-resolved optically stimulated luminescence (TR-OSL), and these signals can be mathematically described as a sum of 4 exponential components (a, b, c, d). The slowest component, d, increases with the duration of the light pulse as expected from the exponential model. The stimulation temperature dependence experiment...

  3. IR-RF dating on K-feldspar: tracing environmental changes in the Middle Pleistocene?

    Science.gov (United States)

    Kreutzer, Sebastian; Frouin, Marine; Krishna Murari, Madhav; Fuchs, Markus; Mercier, Norbert

    2017-04-01

    In Quaternary sciences, luminescence dating (OSL, TL, RF) yielded paramount importance due to its capability to trace the geomorphological process itself. However, every method has its own limitation and, e.g., the choice of a mineral depends on its local availability and mineral specific characteristic. Since quartz has been proved as reliable dosimeter, but its usual dose saturation level of ca. 150 Gy might be not sufficient in particular cases, feldspar grains are preferred for dating events where higher saturation limits are desired or quartz is not available. However, feldspar suffers from anomalous fading and the efforts undertaken during the last decades to overcome this challenge varied in their success. By contrast, infrared radiofluorescence (IR-RF) of K-feldspar (Trautmann et al., 1999) seems to offer a promising alternative, but until date it has been rarely applied. Likely reasons for this lack of attention are a shortage of commercially available measurement equipment until the recent past and serious methodological doubts that had been raised in the literature (e.g., Buyleart et al., 2012). At the IRAMAT-CRP2A the formerly proposed IR-RF single aliquot regenerative dose (SAR) protocol approach (IRSAR, Erfurt et al., 2003) for K-feldspar grains have been adapted and enhanced (Frouin et al., 2015; Huot et al., 2015; Frouin et al., 2017) using (a) sample adapted bleaching settings and (b) a stimulation at higher temperatures. Together with more recent methodological findings, we present the advantage and the limitations of using the IR-RF dating approach for establishing reliable chronologies on believed Middle Pleistocene sediments. References. Buylaert, J.P., Jain, M., Murray, A.S., Thomsen, K.J., Lapp, T., 2012. IR-RF dating of sand-sized K-feldspar-extracts: A test of accuracy. Radiation Measurements 47, 759-765. Erfurt, G., Krbetschek, M.R., 2003. IRSAR - A single-aliquot regenerative-dose dating protocol applied to the infrared radiofluorescence

  4. Quantitative analysis of time-resolved infrared stimulated luminescence in feldspars

    Energy Technology Data Exchange (ETDEWEB)

    Pagonis, Vasilis, E-mail: vpagonis@mcdaniel.edu [McDaniel College, Physics Department, Westminster, MD 21157 (United States); Ankjærgaard, Christina [Soil Geography and Landscape Group & Netherlands Centre for Luminescence dating, Wageningen University, PO Box 47, 6700 AA Wageningen (Netherlands); Jain, Mayank [Center for Nuclear Technologies, Technical University of Denmark, DTU Risø Campus, Roskilde (Denmark); Chithambo, Makaiko L. [Department of Physics and Electronics, Rhodes University, PO BOX 94, Grahamstown 6140 (South Africa)

    2016-09-15

    Time-resolved infrared-stimulated luminescence (TR-IRSL) from feldspar samples is of importance in the field of luminescence dating, since it provides information on the luminescence mechanism in these materials. In this paper we present new analytical equations which can be used to analyze TR-IRSL signals, both during and after short infrared stimulation pulses. The equations are developed using a recently proposed kinetic model, which describes localized electronic recombination via tunneling between trapped electrons and recombination centers in luminescent materials. Recombination is assumed to take place from the excited state of the trapped electron to the nearest-neighbor center within a random distribution of luminescence recombination centers. Different possibilities are examined within the model, depending on the relative importance of electron de-excitation and recombination. The equations are applied to experimental TR-IRSL data of natural feldspars, and good agreement is found between experimental and modeling results.

  5. Microfluidic Leaching of Soil Minerals: Release of K+ from K Feldspar.

    Directory of Open Access Journals (Sweden)

    Davide Ciceri

    Full Text Available The rate of K+ leaching from soil minerals such as K-feldspar is believed to be too slow to provide agronomic benefit. Currently, theories and methods available to interpret kinetics of mineral processes in soil fail to consider its microfluidic nature. In this study, we measure the leaching rate of K+ ions from a K-feldspar-bearing rock (syenite in a microfluidic environment, and demonstrate that at the spatial and temporal scales experienced by crop roots, K+ is available at a faster rate than that measured with conventional apparatuses. We present a device to investigate kinetics of mineral leaching at an unprecedented simultaneous resolution of space (~101-102 μm, time (~101-102 min and fluid volume (~100-101 mL. Results obtained from such a device challenge the notion that silicate minerals cannot be used as alternative fertilizers for tropical soils.

  6. Combining infrared- and green-laser stimulation sources in single-grain luminescence measurements of feldspar and quartz

    DEFF Research Database (Denmark)

    Duller, G.A.T.; Bøtter-Jensen, L.; Murray, A.S.

    2003-01-01

    on grains from two feldspar samples are described. These show that the ratio of the OSL signal under green and IR stimulation is similar for all the feldspar grains. As expected, the ratio for quartz grains is very different, with a much weaker signal when using IR stimulation. For the two feldspars......, the distribution of OSL between the grains and the saturation of the dose response curve shows much less variability than is typically seen for quartz grains. (C) 2003 Elsevier Science Ltd. All rights reserved....

  7. Preparation of ultrafine silica from potash feldspar using sodium carbonate roasting technology

    Institute of Scientific and Technical Information of China (English)

    Jia-nan Liu; Xiao-yi Shen; Yan Wu; Jun Zhang; Yu-chun Zhai

    2016-01-01

    A novel process was developed for the preparation of ultrafine silica from potash feldspar. In the first step, potash feldspar was roasted with Na2CO3 and was followed by leaching using NaOH solution to increase the levels of potassium, sodium, and aluminum in the solid residue. The leaching solution was then carbonated to yield ultrafine silica. The optimized reaction conditions in the roasting process were as follows:an Na2CO3-to-potash feldspar molar ratio of 1.1, a reaction temperature of 875°C, and a reaction time of 1.5 h. Under these conditions, the extraction rate of SiO2 was 98.13%. The optimized carbonation conditions included a final solution pH value of 9.0, a tem-perature of 40°C, a CO2 flow rate of 6 mL/min, a stirring intensity of 600 r/min, and an ethanol-to-water volume ratio of 1:9. The precipita-tion rate and granularity of the SiO2 particles were 99.63%and 200 nm, respectively. We confirmed the quality of the obtained ultrafine sil-ica by comparing the recorded indexes with those specified in Chinese National Standard GB 25576―2010.

  8. Concerning infrared-stimulated luminescence from K-feldspars: evidence from heating before stimulating

    CERN Document Server

    Galloway, R B

    1999-01-01

    Repeated heating and stimulation by infrared of feldspar samples causes a reduction in the luminescence signal. Two feldspars were investigated, one microcline and one orthoclase. Empirically the fraction of luminescence signal f(n) remaining after the nth cycle of heating and stimulation is given by f(n)=1-a ln(n) for laboratory dosed samples of both microcline and orthoclase feldspars, for heating temperatures of 150 deg. C, 180 deg. C and 220 deg. C, for heating durations per cycle ranging from 20 s to 2400 s and with the study covering 10 cycles of heating and stimulation. Logarithmic decay of luminescence with time has been explained previously, in other contexts, as due either to quantum tunnelling or to a continuous distribution of states being involved but it is shown that these explanations do not fit the present data. The measured data on f(n) were corrected for the loss of luminescence due to infrared stimulation to ensure that this did not account for the differences between the data and the expec...

  9. Preparation of ultrafine silica from potash feldspar using sodium carbonate roasting technology

    Science.gov (United States)

    Liu, Jia-nan; Shen, Xiao-yi; Wu, Yan; Zhang, Jun; Zhai, Yu-chun

    2016-08-01

    A novel process was developed for the preparation of ultrafine silica from potash feldspar. In the first step, potash feldspar was roasted with Na2CO3 and was followed by leaching using NaOH solution to increase the levels of potassium, sodium, and aluminum in the solid residue. The leaching solution was then carbonated to yield ultrafine silica. The optimized reaction conditions in the roasting process were as follows: an Na2CO3-to-potash feldspar molar ratio of 1.1, a reaction temperature of 875°C, and a reaction time of 1.5 h. Under these conditions, the extraction rate of SiO2 was 98.13%. The optimized carbonation conditions included a final solution pH value of 9.0, a temperature of 40°C, a CO2 flow rate of 6 mL/min, a stirring intensity of 600 r/min, and an ethanol-to-water volume ratio of 1:9. The precipitation rate and granularity of the SiO2 particles were 99.63% and 200 nm, respectively. We confirmed the quality of the obtained ultrafine silica by comparing the recorded indexes with those specified in Chinese National Standard GB 25576―2010.

  10. Subsolidus alkali metasomatism in the metamorphosed Ordovician acid volcanics and volcaniclastics of the Gelnica Group (Gemeric Superunit, Western Carpathians

    Directory of Open Access Journals (Sweden)

    Mária Šimurková

    2016-06-01

    Full Text Available The Early Paleozoic Gelnica Group (Gemeric Superunit, Western Carpathians is composed of low-grade metamorphosed flysch-like sedimentary complexes alternated with volcanogenic complexes built up mostly by acid volcaniclastic rocks. Volcaniclastic rocks and small rhyolite bodies Ordovician in age underwent subsolidus alkali metasomatism locally overprinted by multiple stages of younger metamorphic and hydrothermal alterations. The observed variability in chemical compositions indicates that the most of acid volcanic and volcaniclastic rocks experienced potassic or sodium metasomatic alteration, the unaltered or Mg-metasomatised rocks occur less frequently. The dominating K-metasomatism is related mainly to the K-feldspar, partly also biotite and muscovite/sericite formation at the expense of matrix or original feldspar phenocrysts. The Na-metasomatism is connected with albite formation. The highest concentrations of alkalies (up to 13.52 wt. % K2O and 7.08 wt. % Na2O respectively have been found in rocks originally represented by glassy dacites. The elements like Al, Ti and Zr remain immobile in alkaline metasomatic processes in contrast to Rb or metals. Based on the results from areas with analogical geological structure and evolution, especially the Bergslagen area in Sweden, we suppose that alkali metasomatism in the Gelnica Group is a product of hydrothermal system caused by the infiltration and circulation of sea water. The areas with K-, Na- or Mg-metasomatism represent different parts of the original hydrothermal system, where the K-metasomatism was probably its lower temperature section. This hydrothermal system probably mobilised some metals (Cu, Pb, Zn, Fe, Mn for the formation of stratiform sulfide and oxide mineralizations or served as the metal pre-concentrator for younger siderite-sulfide vein deposits.

  11. Magmatic-hydrothermal fluid interaction and mineralization in alkali-syenite nodules from the Breccia Museo pyroclastic deposit, Naples, Italy: Chapter 7 in Volcanism in the Campania Plain — Vesuvius, Campi Flegrei and Ignimbrites

    Science.gov (United States)

    Fedele, Luca; Tarzia, Maurizio; Belkin, Harvey E.; De Vivo, Benedetto; Lima, Annamaria; Lowenstern, Jacob

    2007-01-01

    The Breccia Museo, a pyroclastic flow that crops out in the Campi Flegrei volcanic complex (Naples, Italy), contains alkali-syenite (trachyte) nodules with enrichment in Cl and incompatible elements (e.g., U, Zr, Th, and rare-earth elements). Zircon was dated at ≈52 ka, by U-Th isotope systematics using a SHRIMP. Scanning electron microscope and electron microprobe analysis of the constituent phases have documented the mineralogical and textural evolution of the nodules of feldspar and mafic accumulations on the magma chamber margins. Detailed electron microprobe data are given for alkali and plagioclase feldspar, salite to ferrosalite clinopyroxene, pargasite, ferrogargasite, magnesio-hastingsite hornblende amphibole, biotite mica, Cl-rich scapolite, and a member (probable davyne-type) of the cancrinite group. Detailed whole rock, major and minor element data are also presented for selected nodules. A wide variety of common and uncommon accessory minerals were identified such as zircon, baddeleyite, zirconolite, pollucite, sodalite, titanite, monazite, cheralite, apatite, titanomagnetite and its alteration products, scheelite, ferberite, uraninite/thorianite, uranpyrochlore, thorite, pyrite, chalcopyrite, and galena. Scanning electron microscope analysis of opened fluid inclusions identified halite, sylvite, anhydrite, tungstates, carbonates, silicates, sulfides, and phosphates; most are probably daughter minerals. Microthermometric determinations on secondary fluid inclusions hosted by alkali feldspar define a temperature regime dominated by hypersaline aqueous fluids. Fluid-inclusion temperature data and mineral-pair geothermometers for coexisting feldspars and hornblende and plagioclase were used to construct a pressure-temperature scenario for the development and evolution of the nodules. We have compared the environment of porphyry copper formation and the petrogenetic environment constructed for the studied nodules. The suite of ore minerals observed in

  12. Igneous phenocrystic origin of K-feldspar megacrysts in granitic rocks from the Sierra Nevada batholith

    Science.gov (United States)

    Moore, J.G.; Sisson, T.W.

    2008-01-01

    Study of four K-feldspar megacrystic granitic plutons and related dikes in the Sierra Nevada composite batholith indicates that the megacrysts are phenocrysts that grew in contact with granitic melt. Growth to megacrystic sizes was due to repeated replenishment of the magma bodies by fresh granitic melt that maintained temperatures above the solidus for extended time periods and that provided components necessary for K-feldspar growth. These intrusions cooled 89-83 Ma, are the youngest in the range, and represent the culminating magmatic phase of the Sierra Nevada batholith. They are the granodiorite of Topaz Lake, the Cathedral Peak Granodiorite, the Mono Creek Granite, the Whitney Granodiorite, the Johnson Granite Porphyry, and the Golden Bear Dike. Megacrysts in these igneous bodies attain 4-10 cm in length. All have sawtooth oscillatory zoning marked by varying concentration of BaO ranging generally from 3.5 to 0.5 wt%. Some of the more pronounced zones begin with resorption and channeling of the underlying zone. Layers of mineral inclusions, principally plagioclase, but also biotite, quartz, hornblende, titanite, and accessory minerals, are parallel to the BaO-delineated zones, are sorted by size along the boundaries, and have their long axes preferentially aligned parallel to the boundaries. These features indicate that the K-feldspar megacrysts grew while surrounded by melt, allowing the inclusion minerals to periodically attach themselves to the faces of the growing crystals. The temperature of growth of titanite included within the K-feldspar megacrysts is estimated by use of a Zr-in-titanite geothermometer. Megacryst-hosted titanite grains all yield temperatures typical of felsic magmas, mainly 735-760 ??C. Titanite grains in the granodiorite hosts marginal to the megacrysts range to lower growth temperatures, in some instances into the subsolidus. The limited range and igneous values of growth temperatures for megacryst-hosted titanite grains support the

  13. Structure of Rare-earth/Alkali Halide Complexes

    Science.gov (United States)

    Akdeniz, Z.; Önem, Z. Çiçek; Tosia, M. P.

    2001-11-01

    Vapour complex formation of rare-earth halides with alkali halides strongly increases the volatility of these compounds. We evaluate the structure taken by such complexes having the chemical formulas MRX4, M2RX5 and M3RX6, where X = F or Cl and typically M = Li or Na and R = La. The roles played by the two types of metal atom is investigated in MRX4 complexes by also taking M = K, Rb or Cs and R = Gd or Lu. The main predictions that emerge from our calculations are as follows: (i) in MRX4 a fourfold coordination of the rare-earth atom is accompanied by twofold or threefold coordination of the alkali atom, the energy difference in favour of the twofold-coordination state being about 0.3 eV in the case of the LiF complexing agent but even changing sign as the ionic radius of either the alkali or the halogen is increased; (ii) in M2RX5 a fivefold coordination of the rare-earth atom is energetically more stable than a fourfold one, by again not more than about 0.3 eV; (iii) in M3RX6 the fivefold and sixfold coordinations of the rare-earth atom are energetically competitive; and (iv) in both M2RX5 and M3RX6 each coordination state can be realized in various forms that differ in detail but are close in energy. Bond fluctuations and disorder around the rare-earth atom can be expected to be a general feature at elevated temperatures, both in the vapour and in liquid rare-earth/alkali halide mixtures.

  14. AUthigenic feldspar as an indicator of paleo-rock/water interactions in Permian carbonates of the Northern Calcareous Alps, Austria

    Science.gov (United States)

    Spotl, C.; Kralik, M.; Kunk, M.J.

    1996-01-01

    Dolostones interbedded with Upper Permian evaporites at the base of the Northern Calcareous Alps contain abundant authigenic K-feldspar. Two petrographically, structurally, and isotopically distinct generations of K-feldspar can be distinguished: crystals composed of an inclusion-rich core and a clear rim, and optically unzoned, transparent crystals. Both feldspar types have essentially identical K-feldspar end-member compositions with ??? 99.5 mole % Or component. Low oxygen isotope ratios (+16.1??? to +18.1??? SMOW) suggest precipitation from 18O-enriched, saline fluids at temperatures in excess of ??? 140??C. 40Ar/39Ar plateau-age spectra of five samples range from 145 ?? 1 to 144 ?? 1 Ma (Early Berriasian) and suggest that both types of feldspar were formed within an interval that did not exceed ??? 2 m.y. Rb/Sr model ages range from 152 to 140 Ma, assuming that the burial diagenetic regime was buffered with respect to strontium by the associated marine Permian evaporites. Authigenic K-feldspar records two distinct events of hot brine flow, most likely triggered by tectonic movements (detachment) and by an increase in the subsurface temperature in response to thrust loading.

  15. Evaluation and Beneficiation of Feldspar from Arkosic Sandstone in South Jordan for Application in the Ceramic Industry

    Directory of Open Access Journals (Sweden)

    Mousa Gougazeh

    2006-01-01

    Full Text Available The main purpose of the present study was to investigate the beneficiation and upgrading processes of a Jordanian feldspar ores to be finally implemented in the ceramic industry. The experimental work was conducted to evaluate the role of particle size distribution, chemical composition, mineral content and the magnetic impurities (Fe2O3 +TiO2 contents. The beneficiation of the 500-45 μm fractions, which constitutes about 30% of the ore, assaying 10.9% Al2O3, equivalent to approximately ca 56% feldspar, with a mean of magnetic content of 0.95 % iron and titanium oxides. The relationship of potassic-to-sodic feldspar amounts to approximately 18:1 in the feldspar fraction. High intensity magnetic separation and froth flotation test work was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron contents of the feed to a range between 0.10 and 0. 12% iron oxides with an average yield greater than 85%. Flotation with HF provided a feldspar recovery by 45-55% with a concentrates assaying 17-17.35 % Al2O3. Iron contents were decreased from 0.46-0.68% to 0.17-0.23 %.

  16. Nanosized alkali-metal-doped ethoxotitanate clusters.

    Science.gov (United States)

    Chen, Yang; Trzop, Elzbieta; Makal, Anna; Sokolow, Jesse D; Coppens, Philip

    2013-05-06

    The synthesis and crystallographic characterization of alkali-metal-doped ethoxotitanate clusters with 28 and 29 Ti atoms as well as a new dopant-free Ti28 cluster are presented. The light-metal-doped polyoxotitanate clusters in which the alkali-metal atom is the critical structure-determining component are the largest synthesized so far. Calculations show that doping with light alkali atoms narrows the band gap compared with the nondoped crystals but does not introduce additional energy levels within the band gap.

  17. High effective silica fume alkali activator

    Indian Academy of Sciences (India)

    Vladimír Živica

    2004-04-01

    Growing demands on the engineering properties of cement based materials and the urgency to decrease unsuitable ecologic impact of Portland cement manufacturing represent significant motivation for the development of new cement corresponding to these aspects. One category represents prospective alkali activated cements. A significant factor influencing their properties is alkali activator used. In this paper we present a new high effective alkali activator prepared from silica fume and its effectiveness. According to the results obtained this activator seems to be more effective than currently used activators like natrium hydroxide, natrium carbonate, and water glass.

  18. Process to separate alkali metal salts from alkali metal reacted hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard; Alvare, Javier; Larsen, Dennis; Killpack, Jeff

    2017-06-27

    A process to facilitate gravimetric separation of alkali metal salts, such as alkali metal sulfides and polysulfides, from alkali metal reacted hydrocarbons. The disclosed process is part of a method of upgrading a hydrocarbon feedstock by removing heteroatoms and/or one or more heavy metals from the hydrocarbon feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase containing alkali metal salts and reduced heavy metals, and an upgraded hydrocarbon feedstock. The inorganic phase may be gravimetrically separated from the upgraded hydrocarbon feedstock after mixing at a temperature between about 350.degree. C. to 400.degree. C. for a time period between about 15 minutes and 2 hours.

  19. Optical dating using feldspar from Quaternary alluvial and colluvial sediments from SE Brazilian Plateau, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Tatumi, Sonia H. E-mail: tatumi@fatecsp.br; Peixoto, Maria Naise O.; Moura, Josilda R.S.; Mello, Claudio L.; Carmo, Isabela O.; Kowata, Emilia A.; Yee, Marcio; Brito, Silvio Luiz M.; Gozzi, Giuiliano; Kassab, Luciana R.P

    2003-05-01

    Opticallly stimulated luminescence (OSL) dating has been applied to a wide variety of materials such as loess, sand dunes, colluvium, alluvium, volcanic products, etc., helping geologic geomorphologic studies. OSL dating results using feldspar crystals extracted from alluvial and colluvial deposits of SE Brazilian Plateau will be presented in this work. The methodology used is based on the regeneration method, with multiple aliquot protocol. A total of 23 sample ages were obtained spanning 6.5-97.2 kyr. Results of radioactive contents and comparison with radiocarbon ages will be discussed.

  20. Modeling of the shape of infrared stimulated luminescence signals in feldspars

    DEFF Research Database (Denmark)

    Pagonis, Vasilis; Jain, Mayank; Murray, Andrew S.;

    2012-01-01

    This paper presents a new empirical model describing infrared (IR) stimulation phenomena in feldspars. In the model electrons from the ground state of an electron trap are raised by infrared optical stimulation to the excited state, and subsequently recombine with a nearest-neighbor hole via...... that the shape of the IRSL curves does not change significantly under different experimental conditions. The relationship between the simulated IRSL signal and the well-known power-law dependence of relaxation processes in solids is also explored, by fitting the IRSL signal at long times with a power-law type...

  1. Radiation-induced growth and isothermal decay of infrared-stimulated luminescence from feldspar

    DEFF Research Database (Denmark)

    Guralnik, Benny; Li, Bo; Jain, Mayank

    2015-01-01

    Optically stimulated luminescence (OSL) ages can determine a wide range of geological events or processes, such as the timing of sediment deposition, the exposure duration of a rock surface, or the cooling rate of bedrock. The accuracy of OSL dating critically depends on our capability to describe...... the growth and decay of laboratory-regenerated luminescence signals. Here we review a selection of common models describing the response of infrared stimulated luminescence (IRSL) of feldspar to constant radiation and temperature as administered in the laboratory. We use this opportunity to introduce...

  2. Electrons in feldspar I: On the wavefunction of electrons trapped at simple lattice defects

    DEFF Research Database (Denmark)

    Poolton, H.R.J.; Wallinga, J.; Murray, A.S.

    2002-01-01

    The purpose of this article is to make an initial consideration of the physical properties of electrons trapped at classic hydrogenic lattice defects in feldspar. We are particularly interested to determine the radial extent of the electron wavefunctions in the ground and excited states...... processes in the materials. Under low-energy optical stimulation (hnu similar to 1.4 eV), luminescence can be a competitive process between direct electron-hole tunnelling recombination (with the charge still trapped at the defect sites), and free-to-bound recombination (after the excited state electron...

  3. Quantitative analysis of time-resolved infrared stimulated luminescence in feldspars

    DEFF Research Database (Denmark)

    Pagonis, Vasilis; Ankjærgaard, Christina; Jain, Mayank;

    2016-01-01

    Time-resolved infrared-stimulated luminescence (TR-IRSL) from feldspar samples is of importance in the field of luminescence dating, since it provides information on the luminescence mechanism in these materials. In this paper we present new analytical equations which can be used to analyze TR......-IRSL signals, both during and after short infrared stimulation pulses. The equations are developed using a recently proposed kinetic model, which describes localized electronic recombination via tunneling between trapped electrons and recombination centers in luminescent materials. Recombination is assumed...

  4. Deliberate and Accidental Gas-Phase Alkali Doping of Chalcogenide Semiconductors: Cu(In,Ga)Se2

    Science.gov (United States)

    Colombara, Diego; Berner, Ulrich; Ciccioli, Andrea; Malaquias, João C.; Bertram, Tobias; Crossay, Alexandre; Schöneich, Michael; Meadows, Helene J.; Regesch, David; Delsante, Simona; Gigli, Guido; Valle, Nathalie; Guillot, Jérome; El Adib, Brahime; Grysan, Patrick; Dale, Phillip J.

    2017-02-01

    Alkali metal doping is essential to achieve highly efficient energy conversion in Cu(In,Ga)Se2 (CIGSe) solar cells. Doping is normally achieved through solid state reactions, but recent observations of gas-phase alkali transport in the kesterite sulfide (Cu2ZnSnS4) system (re)open the way to a novel gas-phase doping strategy. However, the current understanding of gas-phase alkali transport is very limited. This work (i) shows that CIGSe device efficiency can be improved from 2% to 8% by gas-phase sodium incorporation alone, (ii) identifies the most likely routes for gas-phase alkali transport based on mass spectrometric studies, (iii) provides thermochemical computations to rationalize the observations and (iv) critically discusses the subject literature with the aim to better understand the chemical basis of the phenomenon. These results suggest that accidental alkali metal doping occurs all the time, that a controlled vapor pressure of alkali metal could be applied during growth to dope the semiconductor, and that it may have to be accounted for during the currently used solid state doping routes. It is concluded that alkali gas-phase transport occurs through a plurality of routes and cannot be attributed to one single source.

  5. Effect of ageing of K-feldspar on its ice nucleating efficiency in immersion, deposition and contact freezing modes

    Science.gov (United States)

    Peckhaus, Andreas; Bachmann, Felix; Hoffmann, Nadine; Koch, Michael; Kiselev, Alexei; Leisner, Thomas

    2015-04-01

    Recently K-feldspar was identified as one of the most active atmospheric ice nucleating particles (INP) of mineral origin [1]. Seeking the explanation to this phenomena we have conducted extensive experimental investigation of the ice nucleating efficiency of K-feldspar in three heterogeneous freezing modes. The immersion freezing of K-feldspar was investigated with the cold stage using arrays of nanoliter-size droplets containing aqueous suspension of polydisperse feldspar particles. For contact freezing, the charged droplets of supercooled water were suspended in the laminar flow of the DMA-selected feldspar-containing particles, allowing for determination of freezing probability on a single particle-droplet contact [2]. The nucleation and growth of ice via vapor deposition on the crystalline surfaces of macroscopic feldspar particles have been investigated in the Environmental Scanning Electron Microscope (ESEM) under humidified nitrogen atmosphere. The ice nucleation experiments were supplemented with measurements of effective surface area of feldspar particles and ion chromatography (IC) analysis of the leached framework cations (K+, Na+, Ca2+, Mg2+). In this contribution we focus on the role of surface chemistry influencing the IN efficiency of K-feldspar, in particular the connection between the degree of surface hydroxylation and its ability to induce local structural ordering in the interfacial layer in water molecules (as suggested by recent modeling efforts). We mimic the natural process of feldspar ageing by suspending it in water or weak aqueous solution of carbonic acid for different time periods, from minutes to months, and present its freezing efficiency as a function of time. Our immersion freezing experiments show that ageing have a nonlinear effect on the freezing behavior of feldspar within the investigated temperature range (-40°C to -10°C). On the other hand, deposition nucleation of ice observed in the ESEM reveals clear different pattern

  6. Relaxation of quadrupole orientation in an optically pumped alkali vapour

    Energy Technology Data Exchange (ETDEWEB)

    Bernabeu, E.; Tornos, J.

    1985-04-01

    The relaxation of quadrupole orientation (alignment) in an optically pumped alkali vapour is theoretically studied by taking into account the relaxation processes by alkali-buffer gas, alkali-alkali with spin exchange and alkali-cell wall (diffusion process) collisions. The relaxation transients of the quadrupole orientation are obtained by introducing a first-order weak-pumping approximation (intermediate pumping) less restrictive than the usually considered (zeroth order) one.

  7. Milk Alkali and Hydrochlorothiazide: A Case Report

    Directory of Open Access Journals (Sweden)

    Babar Parvez

    2011-01-01

    Full Text Available Hypercalcemia is a relatively common clinical problem in both outpatient and inpatient settings. Primary pathophysiology is the entry of calcium that exceeds its excretion into urine or deposition in bone into circulation. Among a wide array of causes of hypercalcemia, hyperparathyroidism and malignancy are the most common, accounting for greater than 90 percent of cases. Concordantly, there has been a resurgence of milk-alkali syndrome associated with the ingestion of large amounts of calcium and absorbable alkali, making it the third leading cause of hypercalcemia (Beall and Scofield, 1995 and Picolos et al., 2005. This paper centers on a case of over-the-counter calcium and alkali ingestion for acid reflux leading to milk alkali with concordant use of thiazide diuretic for hypertension.

  8. Authigenic potassium feldspar: a tracer for the timing of palaeofluid flow in carbonate rocks, Northern Calcareous Alps, Austria

    Science.gov (United States)

    Spotl, C.; Kunk, M.J.; Ramseyer, K.; Longstaffe, F.J.

    1998-01-01

    This paper is included in the Special Publication entitled 'Dating and duration of fluid flow and fluid-rock interaction', edited by J. Parnell. Feldspar is a common authigenic constituent in Permian carbonate rocks which occur as tectonically isolated blocks within the evaporitic Haselgebirge melange in the Northern Calcareous Alps (NCA). Coexisting with pyrite, anhydrite, (saddle) dolomite, magnesite, fluorite and calcite, K-feldspar and minor albite record an event of regionally extensive interaction of hot brines with carbonate rocks. Detailed petrographic, crystallographic and geochemical studies reveal a variability in crystal size and shape, Al-Si ordering, elemental and stable isotopic compositions of the K-feldspar, which is only partially consistent with the traditional view of authigenic feldspar as a well-ordered, compositionally pure mineral. 40Ar-39Ar step- heating measurements of authigenic potassium feldspar from several localities yield two age populations, an older one of 145-154 Ma, and a younger one of c.90-97 Ma. Most age spectra reflect cooling through the argon retention temperature interval, which was rapid in some localities (as indicated by plateau ages) and slower in others. Rb-Sr isotope data are more difficult to interpret, because in many K-feldspar samples they are controlled largely by Sr-bearing inclusions. The Jurassic 40Ar-39Ar dates are interpreted as minimum ages of feldspar growth and hence imply that fluid-rock interaction is likely to be simultaneous with or to slightly predate melange formation. Deformation associated with the closure and subduction of the Meliata-Hallstatt ocean south of the NCA during the Upper Jurassic is regarded as the principal geodynamic driving force for both enhanced fluid circulation and melange formation. Some localities were reheated beyond the argon retention temperature for microcline during mid-Cretaceous nappe stacking of the NCA, thus obliterating the older signal.

  9. Fluorescent sensing and determination of mercury (II) ions in water

    African Journals Online (AJOL)

    2011-11-28

    Nov 28, 2011 ... towards the mercury (II) ion among various alkali, alkaline earth, and transition metal ions. The mercury (II) .... the metal stock solution was added to 13 separate test tubes. The test ..... positive curvature in Stern-Volmer plots.

  10. Intrinsic luminescence of alkali silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Arbuzov, V.I.; Grabovskis, V.Y.; Tolstoi, M.N.; Vitol, I.K.

    1986-09-01

    This study obtains additional information on L centers and their role in electron excitation and intrinsic luminescence of a whole series. (Li, Na, K, Rb, and Cs) of alkali silicate glasses. The authors compare the features of the interaction with radiation of specimens of glass and crystal of a similar chemical composition, since silicates of alkali metals can be obtained in both the glassy and crystalline states.

  11. Alkali ion transport of primycin modified erythrocytes.

    Science.gov (United States)

    Blaskó, K; Györgyi, S

    1981-01-01

    The effects of the antibiotic primycin on alkali cation transport of human erythrocytes were investigated. Primycin selectively increases the permeability of erythrocytes to alkali-cations according to the sequence: Cs+ greater than Rb+ approximately K+ greater than Na+. The time course of the cation effluxes depends on the antibiotic concentration and can be altered by negatively charged SDS. Some evidence is given for the mechanism of primycin-membrane interaction.

  12. Influence of curing conditions on durability of alkali-resistant glass fibres in cement matrix

    Indian Academy of Sciences (India)

    Arabi Nourredine

    2011-07-01

    Glass fibres in concrete material often increase the flexural strength. However, these fibres when in contact with cement are altered by alkali reactions due to the presence of portlandite. This study presents the results of investigation to show the effect of curing conditions on the durability of alkali-resistant glass fibres in cement matrix. Test results show that even alkali resistant fibres treated with zirconium oxide present the same degradation phenomenon. They also show that the nature of the cement has a large influence on the protection of the fibres: the Portland CEM II is less damaging than the CEM I. The substitutions of a part of cement by silica fume gave no substantial improvements to the mechanical strength of the glass fibre reinforced cement (GFRC). However, the observed microstructures in the samples show that the degradation is weakened with the addition of silica fumes. The analytical techniques used in this study are scanning electron microscope (SEM) and X-ray diffraction.

  13. Single-grain dating of young sediments using the pIRIR signal from feldspar

    DEFF Research Database (Denmark)

    Reimann, Tony; Thomsen, Kristina Jørkov; Jain, Mayank;

    2012-01-01

    In this article we test for the first time the potential of single-grains of K-rich feldspar to date well-bleached and poorly bleached sediments using a post-IR IRSL (pIRIR) protocol. We measure natural dose distributions using K-rich feldspars from four coastal samples applying the pIRIR protocol...... with a preheat of 200°C and a pIRIR stimulation temperature of 180°C; each sample had an independent age control obtained from quartz OSL and radiocarbon dating. We also analyse single-grain dose distributions of “zero-dose” and γ-irradiated samples to determine thermal transfer/residual doses and the intrinsic...... sources of variability of pIRIR single-grain measurements, respectively. Based on these experiments, we conclude that thermal transfer/residual dose give rise to an offset of ∼0.6Gy in these samples and that the uncertainty assigned to individual pIRIR single-grain dose estimates cannot be smaller than 16...

  14. Ternary feldspar thermometry of Paleoproterozoic granulites from In-Ouzzal terrane (Western Hoggar, southern Algeria)

    Science.gov (United States)

    Benbatta, A.; Bendaoud, A.; Cenki-Tok, B.; Adjerid, Z.; Lacène, K.; Ouzegane, K.

    2017-03-01

    The In Ouzzal terrane in western Hoggar (Southern Algeria) preserves evidence of ultrahigh temperature (UHT) crustal metamorphism. It consists in Archean crustal units, composed of orthogneissic domes and greenstone belts, strongly remobilized during the Paleoproterozoic orogeny which was recognized as an UHT event (peak T > 1000 °C and P ≈ 9-12 kbar). This metamorphism was essentially defined locally in Al-Mg granulites, Al-Fe granulites and quartzites outcropping in the Northern part of the In Ouzzal terrane (IOT). In order to test and verify the regional spread of the UHT metamorphism in this terrane, ternary feldspar thermometry on varied rock types (Metanorite, Granulite Al-Mg and Orthogneiss) and samples that crop out in different zones of the In Ouzzal terrane. These rocks contain either perthitic, antiperthitic or mesoperthitic parageneses. Ternary feldspars used in this study have clearly a metamorphic origin. The obtained results combined with previous works show that this UHT metamorphism (>900 °C) affected the whole In Ouzzal crustal block. This is of major importance as for future discussion on the geodynamic context responsible for this regional UHT metamorphism.

  15. Comparative study of ice nucleating efficiency of K-feldspar in immersion and deposition freezing modes

    Science.gov (United States)

    Hiron, T.; Hoffmann, N.; Peckhaus, A.; Kiselev, A. A.; Leisner, T.; Flossmann, A. I.

    2016-12-01

    One of the main challenges in understanding the evolution of Earth's climate resides in the understanding the role of ice nucleation on the development of tropospheric clouds as well as its initiation. K-feldspar is known to be a very active ice nucleating particle and this study focuses on the characterization of its activity in two heterogeneous nucleation modes, immersion and deposition freezing.We use a newly built humidity-controlled cold stage allowing the simultaneous observation of up to 2000 identical 0.6-nanoliter droplets containing suspension of mineral dust particles. The droplets are first cooled down to observe immersion freezing, the obtained ice crystals are then evaporated and finally, the residual particles are exposed to the water vapor supersaturated with respect to ice.The ice nucleation abilities for the individual residual particles are then compared for the different freezing modes and correlation between immersion ice nuclei and deposition ice nuclei is investigated.Based on the electron microscopy analysis of the residual particles, we discuss the possible relationship between the ice nucleation properties of feldspar and its microstructure. Finally, we discuss the atmospheric implications of our experimental results, using DESCAM, a 1.5D bin-resolved microphysics model.

  16. Electron detachment energies in high-symmetry alkali halide solvated-electron anions

    Science.gov (United States)

    Anusiewicz, Iwona; Berdys, Joanna; Simons, Jack; Skurski, Piotr

    2003-07-01

    We decompose the vertical electron detachment energies (VDEs) in solvated-electron clusters of alkali halides in terms of (i) an electrostatic contribution that correlates with the dipole moment (μ) of the individual alkali halide molecule and (ii) a relaxation component that is related to the polarizability (α) of the alkali halide molecule. Detailed numerical ab initio results for twelve species (MX)n- (M=Li,Na; X=F,Cl,Br; n=2,3) are used to construct an interpolation model that relates the clusters' VDEs to their μ and α values as well as a cluster size parameter r that we show is closely related to the alkali cation's ionic radius. The interpolation formula is then tested by applying it to predict the VDEs of four systems [i.e., (KF)2-, (KF)3-, (KCl)2-, and (KCl)3-] that were not used in determining the parameters of the model. The average difference between the model's predicted VDEs and the ab initio calculated electron binding energies is less than 4% (for the twelve species studied). It is concluded that one can easily estimate the VDE of a given high-symmetry solvated electron system by employing the model put forth here if the α, μ and cation ionic radii are known. Alternatively, if VDEs are measured for an alkali halide cluster and the α and μ values are known, one can estimate the r parameter, which, in turn, determines the "size" of the cluster anion.

  17. CO2 sequestration in feldspar-rich sandstone: Coupled evolution of fluid chemistry, mineral reaction rates, and hydrogeochemical properties

    Science.gov (United States)

    Tutolo, Benjamin M.; Luhmann, Andrew J.; Kong, Xiang-Zhao; Saar, Martin O.; Seyfried, William E.

    2015-07-01

    To investigate CO2 Capture, Utilization, and Storage (CCUS) in sandstones, we performed three 150 °C flow-through experiments on K-feldspar-rich cores from the Eau Claire formation. By characterizing fluid and solid samples from these experiments using a suite of analytical techniques, we explored the coupled evolution of fluid chemistry, mineral reaction rates, and hydrogeochemical properties during CO2 sequestration in feldspar-rich sandstone. Overall, our results confirm predictions that the heightened acidity resulting from supercritical CO2 injection into feldspar-rich sandstone will dissolve primary feldspars and precipitate secondary aluminum minerals. A core through which CO2-rich deionized water was recycled for 52 days decreased in bulk permeability, exhibited generally low porosity associated with high surface area in post-experiment core sub-samples, and produced an Al hydroxide secondary mineral, such as boehmite. However, two samples subjected to ∼3 day single-pass experiments run with CO2-rich, 0.94 mol/kg NaCl brines decreased in bulk permeability, showed generally elevated porosity associated with elevated surface area in post-experiment core sub-samples, and produced a phase with kaolinite-like stoichiometry. CO2-induced metal mobilization during the experiments was relatively minor and likely related to Ca mineral dissolution. Based on the relatively rapid approach to equilibrium, the relatively slow near-equilibrium reaction rates, and the minor magnitudes of permeability changes in these experiments, we conclude that CCUS systems with projected lifetimes of several decades are geochemically feasible in the feldspar-rich sandstone end-member examined here. Additionally, the observation that K-feldspar dissolution rates calculated from our whole-rock experiments are in good agreement with literature parameterizations suggests that the latter can be utilized to model CCUS in K-feldspar-rich sandstone. Finally, by performing a number of reactive

  18. Correlation of basic TL, OSL and IRSL properties of ten K-feldspar samples of various origins

    Energy Technology Data Exchange (ETDEWEB)

    Sfampa, I.K. [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece); Polymeris, G.S. [Institute of Nuclear Sciences, Ankara University, 06100 Besevler, Ankara (Turkey); Pagonis, V. [McDaniel College, Physics Department, Westminster, MD 21157 (United States); Theodosoglou, E. [Department of Mineralogy-Petrology-Economic Geology, School of Geology, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Tsirliganis, N.C. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, ‘Athena’ R.& I.C., Kimmeria University Campus, GR67100 Xanthi (Greece); Kitis, G., E-mail: gkitis@auth.gr [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece)

    2015-09-15

    Highlights: • OSL and IRSL bleaching behavior of ten K-feldspar samples is presented. • OSL and IRSL decay curves were component resolved using tunneling model. • The growth of integrated OSL and IRSL signals versus time was described by new expression based on tunneling model. • Correlation between TL, OSL and IRSL signals and of all properties with K-feldspar structure was discussed. - Abstract: Feldspars stand among the most widely used minerals in dosimetric methods of dating using thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Having very good dosimetric properties, they can in principle contribute to the dating of every site of archaeological and geological interest. The present work studies basic properties of ten naturally occurring K-feldspar samples belonging to three feldspar species, namely sanidine, orthoclase and microcline. The basic properties studied are (a) the influence of blue light and infrared stimulation on the thermoluminescence glow-curves, (b) the growth of OSL, IRSL, residual TL and TL-loss as a function of OSL and IRSL bleaching time and (c) the correlation between the OSL and IRSL signals and the energy levels responsible for the TL glow-curve. All experimental data were fitted using analytical expressions derived from a recently developed tunneling recombination model. The results show that the analytical expressions provide excellent fits to all experimental results, thus verifying the tunneling recombination mechanism in these materials and providing valuable information about the concentrations of luminescence centers.

  19. Authigenetic K—feldspars and Their Relations to Sn—polymetallic Mineralization in the Dachang Ore Field

    Institute of Scientific and Technical Information of China (English)

    潘家华; G.C.AMSTUTZ

    1993-01-01

    Sn-polymetallic ores at Dachang,Guangxi Autonomous Region,China,are hosted in Middle-Upper Devonian reef limestones,siliceous rocks,banded and lenticular limestones,etc.Two types of orebodies can be distinguished according to their telations to the bedding:one is distributed along the bedding and the.other cuts across the bedding.Sn and sulfide orebodies associated with K-feldspare are mostly characterized by laminated ore structure. Microscopic examinations of K-feldspar-bearing rocks,in conjunction with X-ray diffraction,chemical composiion and cathodoluminescence data for K-feldspars,as well as their telations to mineralization,the authors consider that the K-feldspare are of authigenic origin,subordinate to the epigenetic stage of diagenesis,They resulted from the reaction of mixed,deep-seated,circulating underground hot waters rich in K,Al and Si with argillaceous carbonates during the Indo nesian orogenic movement.It is suggested more attention should be paid to the effect of authigenic K-feldspars on Sn mineralization.In the meantime the event related to circulating underground hot waters should also be taken into account so as to provide new clues to blind ore prospecting.

  20. Authigenic K-NH{sub 4}-feldspar in sandstones: A fingerprint of the diagenesis of organic matter

    Energy Technology Data Exchange (ETDEWEB)

    Ramseyer, K. [Univ. Bern (Switzerland). Geologisches Inst.; Diamond, L.W. [Univ. Bern (Switzerland). Mineralogisch-Petrographisches Inst.; Boles, J.R. [Univ. of California, Santa Barbara, CA (United States). Dept. of Geological Sciences

    1993-11-01

    In arkosic sandstones of the San Joaquin and Los Angeles Basins presently at temperatures between 35 C and 174 C, trace amounts of authigenic K-NH{sub 4}-feldspar are present as microfracture fillings and overgrowths on detrital K-feldspar. Microchemical analyses of this authigenic phase reveal up to 80 mole % buddingtonite. The largest ammonium concentrations are observed in a sandy interval of the Antelope shale (80 mole %) and in the Stevens Sands ({approx} 50 mole %) of the San Joaquin Basin. This latter unit was deposited as a turbidite in the organic-rich Fruitvale Shale, an equivalent of the Antelope Shale. The lowest ammonium contents (0-16 mole %) are present in the shallow-marine Vedder Sands and the marginal marine San Joaquin Formation in the same basin. Petrographic, {delta}{sup 18}O, {delta}{sup 13}C, and {sup 87}Sr/{sup 86}Sr analyses of a dolomite cement that postdates authigenic K-NH{sub 4}-feldspar indicate that the feldspar precipitated below 28 C in the zone of methanogenesis, from pore waters with the same Sr signature as sea water at the time of sedimentation. Authigenic K-NH{sub 4}-feldspar is thus an early-diagenetic phase that crystallized prior to oil migration, under anoxic conditions when organic matter releases ammonium. The source of ammonium is bacterial decay of organic matter in the sandstones themselves and/or in contemporaneous shales.

  1. K-feldspar-quartz and K-feldspar-plagioclase phase boundary interactions in garnet-orthopyroxene gneiss's from the Val Strona di Omegna, Ivrea-Verbano Zone, northern Italy

    Science.gov (United States)

    Harlov, Daniel E.; Wirth, Richard

    A detailed study based on textural observations combined with microanalysis [back scattered electron imaging (BSE) and electron microprobe analysis (EMPA)] and microstructural data transmission electron microscopy (TEM) has been made of K-feldspar micro-veins along quartz-plagioclase phase and plagioclase-plagioclase grain boundaries in granulite facies, orthopyroxene-garnet-bearing gneiss's (700-825°C, 6-8kbar) from the Val Strona di Omegna, Ivrea-Verbano Zone, northern Italy. The K-feldspar micro-veins are commonly associated with quartz and plagioclase and are not found in quartz absent regions of the thin section. This association appears to represent a localised reaction texture resulting from a common high grade dehydration reaction, namely: amphibole+quartz = orthopyroxene+clinopyroxene+plagioclase+K-feldspar+H2O, which occurred during the granulite facies metamorphism of these rocks. There are a number of lines of evidence for this. These include abundant Ti-rich biotite, which was apparently stable during granulite facies metamorphism, and total lack of amphibole, which apparently was not. Disorder between Al and Si in the K-feldspar indicates crystallisation at temperatures >500°C. Myrmekite and albitic rim intergrowths in the K-feldspar along the K-feldspar-plagioclase interface could only have formed at temperatures >500-600°C. Symplectic intergrowths of albite and Ca-rich plagioclase between these albitic rim intergrowths and plagioclase suggest a high temperature grain boundary reaction, which most likely occurred at the start of decompression in conjunction with a fluid phase. Relatively high dislocation densities (>2×109 to 3×109/cm2) in the K-feldspar suggest plastic deformation at temperatures >500°C. We propose that this plastic deformation is linked with the extensional tectonic environment present during the mafic underplating event responsible for the granulite facies metamorphism in these rocks. Lastly, apparently active garnet grain

  2. Ar Ar dating of authigenic K-feldspar: Quantitative modelling of radiogenic argon-loss through subgrain boundary networks

    Science.gov (United States)

    Mark, D. F.; Kelley, S. P.; Lee, M. R.; Parnell, J.; Sherlock, S. C.; Brown, D. J.

    2008-06-01

    We have analysed two distinct generations of authigenic K-feldspar in Fucoid Bed sandstones from An-t-Sron and Skiag Bridge, NW Highlands, Scotland, which have experienced post-growth heating to levels in excess of the predicted Ar-closure temperature. Authigenic K-feldspars show microtextural similarities to patch perthites; that is subgrains separated by dislocation-rich boundary networks that potentially act as fast diffusion pathways for radiogenic argon. The two generations of authigenic K-feldspar in the Fucoid Bed sandstones can be distinguished by different microtextural zones, bulk mineral compositions, fluid-inclusion populations, and inferred temperatures and chemistries of parent fluids. Ar-Ar age data obtained using high-resolution ultraviolet laser ablation, show that the first cementing generation is Ordovician and the second cementing generation is Silurian. Modelling of Ar diffusion using subgrain size as the effective diffusion dimension and a simplified tectono-thermal thrust model assuming transient heating of the Fucoid Beds is inconsistent with observed data. Removal of heat from the thrust zone through rapid flushing of heated fluids rather than transient heating can be invoked to explain the observed Ar-Ar ages for both generations of cement. Alternatively, Ar-diffusion modelling using overgrowth thickness as the effective diffusion dimension instead of subgrain size also yields models that are consistent with both the Fucoid Bed palaeothermal maxima and determined Ar-Ar age ages for the two generations of K-feldspar cement. Based on this alternate explanation, we propose a theoretical microtextural model that highlights fundamental differences between the microtextures of deuterically formed patch perthites and authigenic K-feldspars, explaining the apparent robustness of authigenic K-feldspar with respect to Ar-retention.

  3. Pulsed IRSL: A stable and fast bleaching luminescence signal from feldspar for dating Quaternary sediments

    DEFF Research Database (Denmark)

    Tsukamoto, Sumiko; Kondo, Reisuke; Lauer, Tobias

    2017-01-01

    Elevated temperature post-infrared infrared stimulated luminescence (post-IR IRSL; pIRIR) dating method using feldspar has led to a significant advancement in dating Quaternary sediments, as this signal has been shown to be stable on geological time scales. In comparison to the conventional IRSL...... fading, when the signal is recorded during the off-time of LED stimulation pulses. In this study, we compare the signal bleachability, thermal and athermal stability, and age estimates derived using different measurement methods, i.e., pulsed IRSL measured at 50 °C (pulsed IR50; subscripts refers...... and tephrochronology. We observe that under exposure to solar simulator, the pulsed IR50 signal bleaches as rapidly as the CW IR50, and much more rapidly than the pIRIR signals. Furthermore, the pulsed IR50 signal is also as stable as the pIRIR signals, especially when the middle part of the decay curve is used...

  4. Pre-treatment of desalination feed seawater by Jordanian Tripoli, Pozzolana and Feldspar: batch experiments

    Directory of Open Access Journals (Sweden)

    AIMAN E. AL-RAWAJFEH

    2011-06-01

    Full Text Available In this research, composites of layered double hydroxide (LDH with three Jordanian natural raw materials: Tripoli (T, Pozzolana (P and Feldspar (F were prepared by co-precipitation and have been used for feed seawater pre-treatment. The data reveals that percent adsorption decreased with increase in initial concentration, but the actual amount of adsorbed ions per unit mass of LDH/T-P-F increased with increase in metal ion concentrations. The values of ΔG were negative and within 21 to 26 kJ/mol, while the values of and ΔS were positive, with ΔH within the range of 0.1 to 25 kJ/mol. The values of ΔH, ΔS and ΔG indicate the favorability of physisorption and show that the LDH/T-P-F composites have a considerable potential as adsorbents for the removal of ions from seawater.

  5. Fabrication and characterization of low temperature co-fired cordierite glass–ceramics from potassium feldspar

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Jianfang; Li, Zhen, E-mail: zhenli@cug.edu.cn; Huang, Yanqiu; Li, Fei; Yang, Qiuran

    2014-01-15

    Highlights: • Low cost cordierite glass–ceramics were fabricated from potassium feldspar. • The glass–ceramics could be highly densified below 950 °C. • The glass–ceramics exhibit extraordinary properties. • The glass–ceramics can be used as LTCC substrates. • The excess SiO{sub 2} improved the microstructure and properties of the glass–ceramics. -- Abstract: Cordierite glass–ceramics for low temperature co-fired ceramic (LTCC) substrates were fabricated successfully using potassium feldspar as the main raw material. The sintering and crystallization behaviors of the glass–ceramics were investigated by the differential scanning calorimetry (DSC), X-ray diffraction (XRD), and field emission scanning electron microscope (FESEM). The results indicated that the glass–ceramics could be highly densified at 850 °C and the cordierite was the main crystalline phase precipitated from the glasses in the temperature range between 900 and 925 °C. The study also evaluated the physical properties including dielectric properties, thermal expansion and flexural strength of the glass–ceramics. The glass–ceramics showed low dielectric constants in the range of 6–8 and low dielectric losses in the range of 0.0025–0.01. The coefficients of thermal expansion (CTEs) are between 4.32 and 5.48 × 10{sup −6} K{sup −1} and flexural strength of the glass–ceramics are 90–130 MPa. All of those qualify the glass–ceramics for further research to be used as potential LTCC substrates in the multilayer electronic substrate field. Additionally, the excess SiO{sub 2} acted as a great role in improving the sinterability of the glasses, and the microstructure and dielectric properties of the relevant glass–ceramics.

  6. Alkali-Activated Geopolymers: A Literature Review

    Science.gov (United States)

    2010-07-01

    About Materials and Binders Manufacture” Constr Build Mater (2007), doi:10.1016/j.conbuildmat.2007.03.019 20 Fernandez-Jimenez, A., Garcia-Lodeiro, I...2030, 6 February 2012. 43 Pacheco-Torgal, F et al, “Alkali-Activated Binders: A Review”, Constr Build Mater (2007), doi: 10.1016/j.conbuildmat...cement concretes have a high potential for future use in global development. Pacheco-Torgal, F et al, “Alkali-Activated Binders: A Review”, Constr

  7. Thermal properties of alkali-activated aluminosilicates

    Science.gov (United States)

    Florian, Pavel; Valentova, Katerina; Fiala, Lukas; Zmeskal, Oldrich

    2017-07-01

    The paper is focused on measurements and evaluation of thermal properties of alkali-activated aluminosilicates (AAA) with various carbon admixtures. Such composites consisting of blast-furnace slag, quartz sand, water glass as alkali activator and small amount of electrically conductive carbon admixture exhibit better electric and thermal properties than the reference material. Such enhancement opens up new practical applications, such as designing of snow-melting, de-icing or self-sensing systems that do not need any external sensors to detect current condition of building material. Thermal properties of the studied materials were measured by the step-wise transient method and mutually compared.

  8. Infrared stimulated luminescence dating of an Eemian (MIS 5e) site in Denmark using K-feldspar

    DEFF Research Database (Denmark)

    Buylaert, Jan-Pieter; Huot, Sebastian; Murray, Andrew S.

    2011-01-01

    Infrared stimulated luminescence (IRSL) dating of K-feldspars may be an alternative to quartz optically stimulated luminescence (OSL) dating when the quartz OSL signal is too close to saturation or when the quartz luminescence characteristics are unsuitable. In this paper, Eemian (MIS 5e) coastal...

  9. Sorption mechanisms of cephapirin, a veterinary antibiotic, onto quartz and feldspar minerals as detected by Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, Jonathan W., E-mail: peterson@hope.ed [Department of Geological and Environmental Sciences, Hope College, P.O. Box 9000, Holland, MI 49422-9000 (United States); O' Meara, Theresa A. [Department of Geological and Environmental Sciences, Hope College, P.O. Box 9000, Holland, MI 49422-9000 (United States); Seymour, Michael D. [Department of Chemistry, Hope College, P.O. Box 9000, Holland, MI 49422-9000 (United States); Wang Wei; Gu Baohua [Environmental Sciences Division, Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States)

    2009-06-15

    Raman spectroscopy was used to investigate sorption mechanisms of cephapirin (CHP), a veterinary antibiotic, onto quartz (SiO{sub 2}) and feldspar (KAlSi{sub 3}O{sub 8}) at different pH. Sorption occurs by electrostatic attraction, monodentate and bidentate complexation. The zwitterion (CHP{sup o}) adsorbs to a quartz{sup (+)} surface by electrostatic attraction of the carboxylate anion group (-COO{sup -}) at low pH, but adsorbs to a quartz{sup (-)} surface through electrostatic attraction of the pyridinium cation, and possibly COO{sup -} bridge complexes, at higher pH. CHP{sup -} bonds to quartz{sup (-)} surfaces by bidentate complexation between one oxygen of -COO{sup -} and oxygen from carbonyl of an acetoxymethyl group. On a feldspar{sup (+/-)} surface, CHP{sup o} forms monodentate complexes between C=O, and possible -COO{sup -} bridges and/or electrostatic attachments to localized edge (hydr)oxy-Al surfaces. CHP{sup -} adsorbs to feldspar{sup (-)} through monodentate C=O complexation. Similar mechanisms may operate for other cephalosporins. Results demonstrate, for the first time, that Raman techniques can be effective for evaluating sorption mechanisms of antibiotics. - Raman spectroscopy indicates that cephapirin, a veterinary antibiotic, sorbs to quartz and feldspar by electrostatic attraction, and monodentate and bidentate complexation.

  10. Combining infrared- and green-laser stimulation sources in single-grain luminescence measurements of feldspar and quartz

    Energy Technology Data Exchange (ETDEWEB)

    Duller, G.A.T. E-mail: ggd@aber.ac.uk; Boetter-Jensen, L.; Murray, A.S

    2003-10-01

    A system designed for measurement of the optically stimulated luminescence (OSL) from individual sand-sized mineral grains has been constructed. Previously, this system was equipped only with a green laser emitting at 532 nm, but now an infrared (IR) laser at 830 nm has been added. It is now possible to interchangeably use the two laser sources for optical stimulation. This is especially valuable for the measurement of feldspars. The power density using the IR laser at the grain is {approx}500 W cm{sup -2}, and stimulation for 1 s reduces the OSL signal to near background level. Initial results on grains from two feldspar samples are described. These show that the ratio of the OSL signal under green and IR stimulation is similar for all the feldspar grains. As expected, the ratio for quartz grains is very different, with a much weaker signal when using IR stimulation. For the two feldspars, the distribution of OSL between the grains and the saturation of the dose response curve shows much less variability than is typically seen for quartz grains.

  11. Luminescence dating of the PASADO core 5022-1D from Laguna Potrok Aike (Argentina) using IRSL signals from feldspar

    DEFF Research Database (Denmark)

    Buylaert, Jan-Pieter; Murray, A.S.; Gebhardt, A.C.;

    2013-01-01

    We have measured and tested a luminescence chronology for the PASADO core 5022-1D from the maar lake of Laguna Potrok Aike. Because of unsuitable quartz OSL characteristics, sand-sized K-feldspar extracts were chosen as a dosimeter and the dose was measured using a post-IR IRSL (pIRIR290) measure...

  12. An efficient methodology for utilization of K-feldspar and phosphogypsum with reduced energy consumption and CO2 emissions

    Institute of Scientific and Technical Information of China (English)

    Zhixi Gan; Zheng Cui; Hairong Yue; Siyang Tang; Changjun Liu; Chun Li; Bin Liang; Heping Xie

    2016-01-01

    The issues of reducing CO2 emissions, sustainably utilizing natural mineral resources, and dealing with industrial waste offer challenges for sustainable development in energy and the environment. We propose an efficient methodology via the co-reaction of K-feldspar and phosphogypsum for the extraction of soluble potassium salts and recovery of SO2 with reduced CO2 emission and energy consumption. The results of characterization and reactivity evaluation indicated that the partial melting of K-feldspar and phosphogypsum in the high-temperature co-reaction significantly facilitated the reduction of phosphogypsum to SO2 and the exchange of K+(K-feldspar) with Ca2+(CaSO4 in phosphogypsum). The reaction parameters were systematical y investigat-ed with the highest sulfur recovery ratio of~60%and K extraction ratio of~87.7%. This novel methodology possesses an energy consumption reduction of~28%and CO2 emission reduction of~55%comparing with the present typical commercial technologies for utilization of K-feldspar and the treatment of phosphogypsum.

  13. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Science.gov (United States)

    2010-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting under...

  14. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Science.gov (United States)

    2010-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject to...

  15. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151) is...

  16. Towards a non-fading signal in feldspar: Insight into charge transport and tunnelling from time-resolved optically stimulated luminescence

    DEFF Research Database (Denmark)

    Jain, Mayank; Ankjærgaard, Christina

    2011-01-01

    Feldspars are an attractive alternative to quartz for extending the dose range, and for dating volcanic terrains such as on Mars and Iceland. Unfortunately, charge stored in the feldspar lattice undergoes anomalous fading leading to an underestimation in the dose estimates. In this paper we use...

  17. Reactive transport modeling of coupled feldspar dissolution and secondary mineral precipitation and its implication for diagenetic interaction in sandstones

    Science.gov (United States)

    Yuan, Guanghui; Cao, Yingchang; Gluyas, Jon; Jia, Zhenzhen

    2017-06-01

    Dissolution of feldspars and precipitation of secondary minerals (kaolinite, illite and quartz) are significant diagenetic processes in arkosic sandstones. We examined moderately buried sandstones in the Eocene Shahejie Formation from two sags in the Bohai Bay Basin, East China. Three different types of mineral assemblages (MA) were identified: extensively leached feldspars with a large amount of authigenic kaolinite and quartz cement (MA-1), extensively leached feldspars with a large amount of authigenic kaolinite and minor quartz cement (MA-2), and extensively leached feldspars with a small amount of both authigenic kaolinite and quartz cement (MA-3). Numerical simulations at the continuum scale using Geochemist's Workbench 9.0 were conducted to decipher the origin of the different mineral assemblages. The physicochemical reactions including feldspar dissolution, transport of Al3+ and SiO2(aq), and precipitation of kaolinite and quartz are coupled together in these simulations, with constraints of chemical reactions, kinetic law, dispersion, and advection. Modeling results suggest that a dissolution zone, a transitional zone, and a precipitation zone can be formed in a sandstone unit with suitable constraints of temperature, flow rate, fluid composition and mineral reaction rate. And MA-3, MA-2, and MA-1 assemblages develop in these three zones respectively. The higher SiO2(aq) concentration required for the saturation of quartz than for kaolinite and the low Al3+ concentration needed for the saturation of kaolinite lead to the precipitation of only kaolinite in the transitional zone in a geochemical system with feldspar dissolution serving as the dominant source of SiO2(aq) and Al3+. Comparisons between modeling results and observations of natural sandstone diagenesis suggest that an MA-1 assemblage is likely to occur in buried sandstones at high temperatures (>70-80 °C) and low flow rates. An MA-2 assemblage may occur in moderately buried sandstones at

  18. Multiple Feldspar replacement in Hercynian granites of the Montseny-Guilleries Massif (Catalan Coastal Ranges, NE Spain)

    Science.gov (United States)

    Fàbrega, Carles; Parcerisa, David; Gómez-Gras, David

    2013-04-01

    The core of the Montseny-Guilleries Massif (Catalan Coastal Ranges) is mainly composed by late-Hercynian granitoids (leucogranites and granodiorites) intruded within Cambrian to Carnoniferous metasediments. The granites are unconformably covered by Triassic (Buntsandstein) and Paleocene red beds at the western boundary, preserving a continuous outcrop of the Permo-Triassic unconformity for about 20 km. In the southwestern Montseny-Guilleries Massif the granites are covered by the Buntsandstein red sandstones that overlain a peneplain paleorelief called the Permo-Triassic palaeosurface. Beneath the palaeosurface the granite displays a characteristic pink colouration. This pink alteration is characterized by precipitation of minute heamatite crystals and albitization of pristine plagioclases (mostly labradorite). The secondary albite is pseudomorphic (mono- or polycrystalline), optically continuous, non-luminiscent, contains widespread microporosity and displays compositions about Ab98. These features are typical of low temperature replacive feldspars (Kastner and Siever, 1979). Albitization of plagioclases is almost total close to the Permo-Triassic palaeosurface and progressively decreases towards depth, displaying a 150-200 m thick alteration profile. The formation of this profile was controlled by fluid circulation along macro- and microfractures and crystal boundaries. Inside the plagioclase crystals fluid pathways were microfractures, twinning and cleavage planes and crystalline defects. The secondary albite holds widespread unconnected micron-size porosity often filled by Fe-oxides. The reaction front is sharp and displays an abrupt composicional change (Ab65 to Ab98) at micron scale. Porosity only appears to be connected at this reaction front surface. The geometrical arrangement of this alterations suggest that albitization was a shallow process related with Na-rich descending fluids linked to the Permo-Triassic palaeosurface, in a similar way to

  19. Analysis of Melting for Alkali Earth and Alkali Oxides Based on the Diffusional Force Theory

    Science.gov (United States)

    Liu, Quan; Chen, Li-Rong

    An analysis of the melting alkali earth and alkali oxides is presented using the concept of diffusional force. The calculations are performed by developing an ionic model based on Harrison's quantum mechanical treatment of overlap repulsive potential which takes into account the interactions up to second neighbors. Van der Waals dipole-dipole and dipole-quadrupole interactions calculated by more accurate methods are also included in the model. Using the formula by Fang, derived on the basis of thermodynamic analysis, the values of interionic distances for 8 alkali earth and alkali oxides at melting have been obtained. A simple model for melting is developed based on the diffusional force models. The values of Tm thus obtained are found to show fairly good agreement with experimental values of melting temperatures.

  20. Luminescence characteristics of quartz and feldspar from tectonically uplifted terraces in Kashmir Basin, Jammu and Kashmir, India

    Energy Technology Data Exchange (ETDEWEB)

    Jaiswal, Manoj K. [Department of Geosciences, National Taiwan University, Roosevelt Road, sec. 4, Taipei, Taiwan (China)], E-mail: mkjosl@gmail.com; Bhat, M.I.; Bali, B.S.; Ahmad, Shabir [Department of Geology and Geophysics, University of Kashmir, Srinagar, Jammu and Kashmir (India); Chen, Y.G. [Department of Geosciences, National Taiwan University, Roosevelt Road, sec. 4, Taipei, Taiwan (China)

    2009-05-15

    The Kashmir Valley or the Jhelum basin is an intermontane-basin in NW Himalaya bounded by the Pir Panjal Range in the south and southwest and the Great Himalayan Range in the north and northeast. The valley is marked by active major thrust boundaries in its south and southwestern parts. Remote sensing studies and morphometric analysis suggest neo-tectonic activities and the formation of tectonic terraces due to uplift on the major thrust boundaries in NW Himalayas. The quartz from freshly eroded mountain belts is usually found to show very poor luminescence sensitivity and thus not suitable for optical dating. Similar problems occurred with the quartz from the Srinagar Basin. Due to this, feldspar was selected as a natural dose meter for dating tectonically uplifted terraces in an active and dynamic belt of the NW Himalayas. We report here for the first time the luminescence characteristics of quartz and feldspar minerals from the study area. However, feldspar also shows poor luminescence sensitivity, although enough to perform optical dating. Athermal fading was observed in all the feldspar samples, which was corrected using 'g' values; a large scatter was found in the g values, probably due to intermixing of feldspar grains from varying source rock types and also due to poor luminescence sensitivity. An average g value correction to the mean paleodose was found to agree if compared with the thermo-luminescence date of loess deposit dated earlier. The ages show that the terrace formation started taking place at {approx}100 ka in the southwestern part of the Jhelum basin and continued with pulses at 50 ka and 11 ka towards the northwestern part.

  1. Positronium impact ionization of Alkali atoms

    CERN Document Server

    Ghosh, D

    2015-01-01

    Target ionization processes of alkali atoms by Positronium impact are investigated. Calculations are performed in the frame work of model potential formalism using the Coulomb distorted eikonal approximation. Interesting qualitative features are noted both in the scattered Ps and the ejected electron distributions in differential as well as double differential levels of the collision cross sections.

  2. Plasma assisted measurements of alkali metal concentrations in pressurized combustion processes

    Energy Technology Data Exchange (ETDEWEB)

    Hernberg, R.; Haeyrinen, V. [Tampere Univ. of Technology (Finland). Dept. of Physics

    1996-12-01

    The plasma assisted method for continuous measurement of alkali concentrations in product gas flows of pressurized energy processes will be tested and applied at the 1.6 MW PFBC/G facility at Delft University of Technology in the Netherlands. During the reporting period the alkali measuring device has been tested under pressurized conditions at VTT Energy, DMT, Foster-Wheeler Energia and ABB Carbon. Measurements in Delft will be performed during 1996 after installation of the hot gas filter. The original plan for measurements in Delft has been postponed due to schedule delays in Delft. The results are expected to give information about the influence of different process conditions on the generation of alkali vapours, the comparison of different methods for alkali measurement and the specific performance of our system. This will be the first test of the plasma assisted measurement method in a gasification process. The project belongs to the Joule II extension program under contract JOU2-CT93-0431. (author)

  3. IR-RF dating of sand-sized K-feldspar extracts: A test of accuracy

    DEFF Research Database (Denmark)

    Buylaert, Jan-Pieter; Jain, Mayank; Murray, A.S.;

    2012-01-01

    In this paper we use a recently developed radioluminescence (RL) attachment to the Risø TL/OSL reader to test the InfraRed-RadioFluorescence (IR-RF) dating method applied to K-feldspar rich extracts from our known-age archive samples. We present experiments to characterise the instrument......-RF ages on a set of samples with independent age control using a robust analytical method, which is able to detect any possible sensitivity change. Our IR-RF ages do not agree well with the independent age control; the ages of the younger samples (20–45 ka) are significantly over-estimated while the ages...... performance and to test the reproducibility of IR-RF measurements. These experiments illustrate the high sensitivity and dose rate of our RL system, the negligible influence of the turntable movement on IR-RF signals and the effectiveness of the built in 395 nm LED at bleaching IR-RF signals. We measure IR...

  4. Infrared and Raman spectroscopic studies on alkali borate glasses: evidence of mixed alkali effect.

    Science.gov (United States)

    Padmaja, G; Kistaiah, P

    2009-03-19

    A lithium-potassium-borate glass system containing manganese and iron cations has been thoroughly investigated in order to obtain information about the mixed alkali effect and the structural role of both the manganese and iron in such glass hosts. Mixed alkali borate glasses of the (30 - x)Li(2)O - xK(2)O - 10CdO/ZnO - 59B(2)O(3) (x = 0, 10, 15, 20, and 30) doped with 1MnO(2)/1Fe(2)O(3) system were prepared by a melt quench technique. The amorphous phase of the prepared glass samples was confirmed from their X-ray diffraction. The spectroscopic properties of glass samples were studied using infrared (IR) and Raman spectroscopic techniques. The density of all the prepared glasses was measured using Archimedes principle. Molar volumes were estimated from the density data. IR spectra of these glasses revealed a dramatic variation of three- and four-coordinated boron structures as a function of mixed alkali concentration. The vibrations due to Li-O, K-O, and MnO(4)/FeO(4) arrangements are consistent in all the compositions and show a nonlinear variation in the intensity with alkali content. Raman spectra of different alkali combinations with CdO and ZnO present drastic changes in the intensity of various Raman bands. The observation of disappearance and reappearance of IR and Raman bands as a function of various alkali concentrations is an important result pertaining to the mixed alkali effect in borate glasses. Acting as complementary spectroscopic techniques, both types of measurements, IR and Raman, revealed that the network structure of the studied glasses is mainly based on BO(3) and BO(4) units placed in different structural groups, the BO(3) units being dominant. The measured IR and Raman spectra of different glasses are used to clarify the optical properties of the present glasses correlating them with their structure and composition.

  5. Local structure of alkalis in mixed-alkali borate glass to elucidate the origin of mixed-alkali effect

    Directory of Open Access Journals (Sweden)

    Yomei Tokuda

    2015-12-01

    Full Text Available We report the structural analysis of Na+ and Cs+ in sodium cesium borate crystals and glasses using 23Na and 133Cs magic-angle spinning nuclear magnetic resonance (MAS NMR spectroscopy. The composition dependence of NMR spectra of the borate was similar to that of the silicate: (1 the peak position of cesium borate crystals shifted to upfield for structures with larger Cs+ coordination numbers, (2 the MAS NMR spectra of xNa2O-yCs2O-3B2O3 (x = 0, 0.25, 0.5, 0.75, 1.0, x + y = 1 glass showed that the average coordination number (CN of both the alkali cations decreases with increasing Cs+/(Na+ + Cs+ ratio. However, the degree of decrement in borates is much smaller than that in silicates. We have considered that the small difference in CN is due to 4-coordinated B, because it is electrically compensated by the alkali metal ions resulting in the restriction of having various coordinations of O to alkali metal.

  6. Infrared spectra of FHF - in alkali halides

    Science.gov (United States)

    Chunnilall, C. J.; Sherman, W. F.

    1982-03-01

    The bifluoride ion, FHF -, has been substitutionally isolated within single crystal samples of several different alkali halides. Infrared spectra of these crystals have been studied for sample temperatures down to 8K when half-bandwidths of less than 1 cm -1 have been observed. (Note that at room temperature ν 3 is observed to have a half-bandwidth of about 40 cm -1). The frequency shifts and half-bandwidth changes caused by cooling are considered together with the frequency shifts caused by pressures up to 10 k bar. The low temperature spectra clearly indicate that FHF - is a linear symmetrical ion when substitutionally isolated within alkali halides of either the NaCl or CsCl structure.

  7. Removal of Retired Alkali Metal Test Systems

    Energy Technology Data Exchange (ETDEWEB)

    Brehm, W. F.; Church, W. R.; Biglin, J. W.

    2003-02-26

    This paper describes the successful effort to remove alkali metals, alkali metal residues, and piping and structures from retired non-radioactive test systems on the Hanford Site. These test systems were used between 1965 and 1982 to support the Fast Flux Test Facility and the Liquid Metal Fast Breeder Reactor Program. A considerable volume of sodium and sodium-potassium alloy (NaK) was successfully recycled to the commercial sector; structural material and electrical material such as wiring was also recycled. Innovative techniques were used to safely remove NaK and its residues from a test system that could not be gravity-drained. The work was done safely, with no environmental issues or significant schedule delays.

  8. Barite in omphacite-hosted K-feldspar + quartz polycrystalline aggregates from the Sulu eclogites and its implications

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    K-feldspar + quartz polycrystalline aggregates were found as sub-millimeter-size inclusions with a pseudomorph after coesite (?) in omphacites from a number of Sulu eclogites. In these aggregates, round or subhedral barites occur as tiny inclusions in either K-feldspar or quartz. Energy dispersive spectroscopy (EDS) analyses show that these barites have (1) 33.86%―41.12% SO3, 0%―34.65% SrO, and 24.12%―63.55% BaO, (2) seemingly negative linear correlations between SrO and BaO, indicating that they are ideal solid solutions of barite (BaSO4) and celestite (SrSO4), and (3) highly variable Sr/Ba molar ratios ranging from 0 to 2.1. Presence of barites in the Sulu eclogites not only indicates oxidation of the subducting continental crust, but also very limited and restricted fluids presented during exhumation of the Sulu UHP eclogites.

  9. Study of sensitivity change of OSL signals from quartz and feldspars as a function of preheat temperature

    DEFF Research Database (Denmark)

    Jungner, H.; Bøtter-Jensen, L.

    1994-01-01

    Optically stimulated luminescence (OSL) signals from feldspar and quartz samples were studied using infrared (860 nm) and green light (420-575 nm) stimulation. A serious problem connected with the regeneration technique used for dating is associated with a change of OSL sensitivity to radiation...... in the couse of the measurement process. A typical effect seen is a large increase of the apparent strength of our beta source when calibrated against a gamma source. If the regeneration procedure is used, it is shown that the sensitivity increases up to similar to 50% during the measurement process...... and as a result, the equivalent dose (ED) would be underestimated. A study of sensitivity changes in feldspars and quartz was carried out with emphasis on the effect of preheat and annealing on the OSL signal. Measurement results obtained are presented, and possible elimination of errors in dating caused...

  10. Effect of Mineral Admixtures on Alkali-Silica Reaction

    Institute of Scientific and Technical Information of China (English)

    ZHANG Chengzhi; WANG Aiqin

    2008-01-01

    The influence of silica fume,slag and fly ash on alkali-silica reaction under the condition of 70℃ is studied.The results show that silica,slag and fly ash may inhibit alkali-silica reaction only under suitable content.When the content is less than 10%,silica fume does not markedly influence the expansion of alkali-silica reaction.When the content is 15%-20%,silica fume only may delay the expansion of alkali-silica reaction.When the content is 30%-70%,slag may only delay the expansion of alkali-silica reaction,but cannot inhibit the expansion of alkali-silica reaction.When the content is 10%,fly ash does not markedly influence the expansion of alkali-silica reaction.When the content is 20%-30%,fly ash may only delay the expansion of alkali-silica reaction,but cannot inhibit the expansion of alkali-silica reaction.When the content is over 50%,it is possible that fly ash can inhibit effectively alkali-silica reaction.

  11. Pyrolysis characteristic of kenaf studied with separated tissues, alkali pulp, and alkali li

    Directory of Open Access Journals (Sweden)

    Yasuo Kojima

    2015-12-01

    Full Text Available To estimate the potential of kenaf as a new biomass source, analytical pyrolysis was performed using various kenaf tissues, i.e., alkali lignin and alkali pulp. The distribution of the pyrolysis products from the whole kenaf was similar to that obtained from hardwood, with syringol, 4-vinylsyringol, guaiacol, and 4-vinylguaiacol as the major products. The phenols content in the pyrolysate from the kenaf core was higher than that from the kenaf cuticle, reflecting the higher lignin content of the kenaf core. The ratios of the syringyl and guaiacyl compounds in the pyrolysates from the core and cuticle samples were 2.79 and 6.83, respectively. Levoglucosan was the major pyrolysis product obtained from the kenaf alkali pulp, although glycol aldehyde and acetol were also produced in high yields, as previously observed for other cellulosic materials. Moreover, the pathways for the formation of the major pyrolysis products from alkali lignin and alkali pulp were also described, and new pyrolysis pathways for carbohydrates have been proposed herein. The end groups of carbohydrates bearing hemiacetal groups were subjected to ring opening and then they underwent further reactions, including further thermal degradation or ring reclosing. Variation of the ring-closing position resulted in the production of different compounds, such as furans, furanones, and cyclopentenones.

  12. Sulfate Resistance of Alkali Activated Pozzolans

    OpenAIRE

    Bondar, Dali

    2015-01-01

    The consequence of sulfate attack on geopolymer concrete, made from an alkali activated natural pozzolan (AANP) has been studied in this paper. Changes in the compressive strength, expansion and capillary water absorption of specimens have been investigated combined with phases determination by means of X-ray diffraction. At the end of present investigation which was to evaluate the performance of natural alumina silica based geopolymer concrete in sodium and magnesium sulfate solution, the l...

  13. Static and Dynamic Structure Factors with Account of the Ion Structure for High-temperature Alkali and Alkaline Earth Plasmas

    CERN Document Server

    Sadykova, S P; Tkachenko, I M

    2010-01-01

    The $e-e$, $e-i$, $i-i$ and charge-charge static structure factors are calculated for alkali and Be$^{2+}$ plasmas using the method described by Gregori et al. in \\cite{bibGreg2006}. The dynamic structure factors for alkali plasmas are calculated using the method of moments \\cite{bibAdam83}, \\cite{bibAdam93}. In both methods the screened Hellmann-Gurskii-Krasko potential, obtained on the basis of Bogolyubov's method, has been used taking into account not only the quantum-mechanical effects but also the ion structure \\cite{bib73}. PACS: 52.27.Aj (Alkali and alkaline earth plasmas, Static and dynamic structure factors), 52.25.Kn (Thermodynamics of plasmas), 52.38.Ph (X-ray scattering)

  14. [The characteristics of microstructure and chemical compositions of K-feldspar, sphene and zircon with zoning structure].

    Science.gov (United States)

    Liu, Chun-Hua; Wu, Cai-Lai; Lei, Min; Qin, Hai-Peng; Li, Ming-Ze

    2013-08-01

    K-feldspar, sphene and zircon in quartz monzonite from Shahewan, south Qinling, showing strong zoning structure. Characteristics of microstructure and chemical compositions of K-feldspar, sphene and zircon with zoning structure were investigated using advanced instruments of electron probe micro analyses equipped with wavelength dispersive spectrometer (EPM-WDS), scanning electron microscopy with energy dispersive spectrometer (SEM-EDS) and laser ablation--inductively coupled plasma--mass spectrometry (LA-ICP-MS). Our study suggests that K+ could be substituted by small amounts of Na+, Ca2+, Ba2+, Fe2+ and Ce3+. Ca2+ in sphene could be replaced by V3+, Ce3+, Ba2+ and Ti4+ could be substituted by both Fe2+ and Al3+. Zircon contains trace elements like Fe, Th, U, Nb, Ta, Y, Hf, Yb and Pb. Concentration of Si, Al, K, Ca, Na, Mg and Ba in K-feldspar ranked from high to low, among which the contents of K and Na are negatively correlated, the lighter part of BSE images featuring K-feldspar is attributed to comparably higher Ba content, additionally, Si and K contents are elevated while Na content decreased rimward. Ca, Si, Ti, Ba, V, Ce, Al and Fe concentration listed downward, among which higher iron content corresponds to brighter portion of BSE images. Element concentration of zircon could be ranked from high to low as Zr, Si, Nd, Ce, Hf, U, Pb and Th, in which Hf and Zr exhibit negatively correlated. Zr concentration increased while Hf, U and Th concentration decreased from core to rim.

  15. Ion Pairing in Alkali Nitrate Electrolyte Solutions.

    Science.gov (United States)

    Xie, Wen Jun; Zhang, Zhen; Gao, Yi Qin

    2016-03-10

    In this study, we investigate the thermodynamics of alkali nitrate salt solutions, especially the formation of contact ion pairs between alkali cation and nitrate anion. The ion-pairing propensity shows an order of LiNO3 activity coefficients and suggest that the empirical "law of matching water affinity" is followed by these alkali nitrate salt solutions. The spatial patterns of contact ion pairs are different in the three salt solutions studied here: Li(+) forms the contact ion pair with only one oxygen of the nitrate while Na(+) and K(+) can also be shared by two oxygens of the nitrate. In reproducing the salt activity coefficient using Kirkwood-Buff theory, we find that it is essential to include electronic polarization for Li(+) which has a high charge density. The electronic continuum correction for nonpolarizable force field significantly improves the agreement between the calculated activity coefficients and their experimental values. This approach also improves the performance of the force field on salt solubility. From these two aspects, this study suggests that electronic continuum correction can be a promising approach to force-field development for ions with high charge densities.

  16. Highly retentive core domains in K-feldspar preserve argon ages from high temperature stages of granite exhumation

    Science.gov (United States)

    Forster, Marnie; Lister, Gordon

    2016-04-01

    Retentive core domains are characterized by diffusion parameters that imply K-feldspar should be able to retain argon even at temperatures near or above the granite solidus. In this case it should be possible to date granite emplacement using argon geochronology, and the same answer should be obtained as by using other methods. We present one case study where this is the case, from the elevated Capoas granite stock on Palawan, in the Philippines, and another where it is not, from the South Cyclades Shear Zone, on Ios, Greece. We attempt to determine the factors such as the role of fluid ingress in triggering the in situ recrystallization that can eliminate and/or modify the core domains, leading to relatively youthful ages. Thermochronology is still possible, because less retentive diffusion domains exist, but different methods need to be applied to interpret the data. The work also demonstrates that K-feldspar can be sufficiently retentive as to allow direct dating of processes that reduce the dimensions of diffusion domains, e.g., cataclased and/or recrystallized K-feldspar in fault rock and/or mylonite. These are important developments in the methodology of 40Ar/39Ar geochronology, but to further advance we need to clarify the nature of these highly retentive core domains. In particular, we need better understand how they are modified by microstructural processes during deformation and metamorphism. We need also to assess the role of any crystal structural changes during step-heating in vacuo.

  17. The effect of microbial glucose metabolism on bytownite feldspar dissolution rates between 5 and 35 C

    Energy Technology Data Exchange (ETDEWEB)

    Welch, S.A.; Ullman, W.J.

    1999-10-01

    The rate of Si release from dissolving bytownite feldspar in abiotic batch reactors increased as temperatures increased from 5 to 35 C. Metabolically inert subsurface bacteria (bacteria in solution with no organic substrate) had no apparent effect on dissolution rates over this temperature range. When glucose was added to the microbial cultures, the bacteria responded by producing gluconic acid, which catalyzed the dissolution reaction by both proton- and ligand-promoted mechanisms. The metabolic production, excretion, and consumption of gluconic acid in the course of glucose oxidation, and therefore, the degree of microbial enhancement of mineral dissolution, depend on temperature. There was little accumulation of gluconic acid and therefore, no significant enhancement of mineral dissolution rates at 35 C compared to the abiotic controls. At 20 C, gluconate accumulated in the experimental solutions only at the beginning of the experiment and led to a twofold increase in dissolved Si release compared to the controls, primarily by the ligand-promoted dissolution mechanism. There was significant accumulation of gluconic acid in the 5 C experiment, which is reflected in a significant reduction in pH, leading to 20-fold increase in Si release, primarily attributable to the proton-promoted dissolution mechanism. These results indicate that bacteria and microbial metabolism can affect mineral dissolution rates in organic-rich, nutrient-poor environments; the impact of microbial metabolism on aluminum silicate dissolution rates may be greater at lower rather than at higher temperatures due to the metabolic accumulation of dissolution-enhancing protons and ligands in solution.

  18. Electrochemistry of ytterbium (III) in molten alkali metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Smolenski, V.; Novoselova, A. [Institute of High-Temperature Electrochemistry, Ural Division, Russian Academy of Science, Ekaterinburg, 620219 (Russian Federation); Osipenko, A. [Research Institute of Atomic Reactors, Dimitrovgrad-10, Ulyanovsk Region, 433010 (Russian Federation); Caravaca, C. [High Level Waste Unit, Nuclear Fission Division, CIEMAT, Madrid, 28040 (Spain); Cordoba, G. de [High Level Waste Unit, Nuclear Fission Division, CIEMAT, Madrid, 28040 (Spain)], E-mail: g.cordoba@ciemat.es

    2008-12-30

    This work presents the electrochemical study of Yb(III) ions in molten alkali metal chlorides in the temperature range 723-1073 K. Transient electrochemical techniques such as linear sweep, cyclic and square wave voltammetry, and potentiometry at zero current have been used to investigate the reduction mechanism, transport parameters and thermodynamic properties of the reaction YbCl{sub 2} + 1/2Cl{sub 2} = YbCl{sub 3} The results obtained show that the reduction reaction Yb(III) + e{sup -} {r_reversible} Yb(II) is reversible being controlled by the rate of the mass transfer. The diffusion coefficient of [YbCl{sub 6}]{sup 3-} complex ions has been determined at different temperatures in the fused eutectic LiCl-KCl, the equimolar NaCl-KCl and the CsCl media. The apparent standard potential of the soluble-soluble redox system Yb(III)/Yb(II) has been obtained by cyclic voltammetry. The influence of the nature of the solvent on the electrochemical and thermodynamic properties of ytterbium compounds is discussed.

  19. Thermalization of different alkali and alkali-earth elements at the TRI{mu}P facility

    Energy Technology Data Exchange (ETDEWEB)

    Shidling, P.D., E-mail: P.Shidling@rug.n [Kernfysisch Versneller Instituut, University of Groningen, Zernikelaan 25, 9747 AA Groningen (Netherlands); Giri, G.S.; Hoek, D.J. van der; Jungmann, K.; Kruithof, W.L.; Onderwater, C.J.G.; Santra, B.; Sohani, M.; Versolato, O.O.; Willmann, L.; Wilschut, H.W. [Kernfysisch Versneller Instituut, University of Groningen, Zernikelaan 25, 9747 AA Groningen (Netherlands)

    2010-10-01

    Radioactive isotopes produced by the in-flight method are converted into low-energy ions with a thermal ionizer (TI) ion catcher, the operation of which is based on a hot cavity ion source. The extraction efficiency of the TI for different alkali and alkali-earth elements has been studied and compared to a model based on diffusion only. The model describes the stationary limit, i.e. the extraction efficiency, as well as the dynamic response of the TI output when the primary beam is switched on and off.

  20. Alkali cation specific adsorption onto fcc(111) transition metal electrodes.

    Science.gov (United States)

    Mills, J N; McCrum, I T; Janik, M J

    2014-07-21

    The presence of alkali cations in electrolyte solutions is known to impact the rate of electrocatalytic reactions, though the mechanism of such impact is not conclusively determined. We use density functional theory (DFT) to examine the specific adsorption of alkali cations to fcc(111) electrode surfaces, as specific adsorption may block catalyst sites or otherwise impact surface catalytic chemistry. Solvation of the cation-metal surface structure was investigated using explicit water models. Computed equilibrium potentials for alkali cation adsorption suggest that alkali and alkaline earth cations will specifically adsorb onto Pt(111) and Pd(111) surfaces in the potential range of hydrogen oxidation and hydrogen evolution catalysis in alkaline solutions.

  1. Correlation of the Na/K ratio in geothermal well waters with the thermodynamic properties of low albite and potash feldspar

    Energy Technology Data Exchange (ETDEWEB)

    Apps, J.A.; Chang, G.M.

    1992-03-01

    The Na/K ratio in geothermal well waters provides a better estimate of the relative stability of low albite and potash feldspar than do predictions from calorimetry and high temperature phase equilibria. The calculated saturation indices from field data for low albite, potash feldspar suggest that [Delta]G[sub f,298][sup o] for the latter should be revised to [minus]3748.6[plus minus]3.7 kJ.mol[sup [minus]1].

  2. Correlation of the Na/K ratio in geothermal well waters with the thermodynamic properties of low albite and potash feldspar

    Energy Technology Data Exchange (ETDEWEB)

    Apps, J.A.; Chang, G.M.

    1992-03-01

    The Na/K ratio in geothermal well waters provides a better estimate of the relative stability of low albite and potash feldspar than do predictions from calorimetry and high temperature phase equilibria. The calculated saturation indices from field data for low albite, potash feldspar suggest that {Delta}G{sub f,298}{sup o} for the latter should be revised to {minus}3748.6{plus_minus}3.7 kJ.mol{sup {minus}1}.

  3. Frictional Properties of Feldspar and Quartz at the Temperatures of Seismogenic Zone

    Science.gov (United States)

    Arai, T.; Masuda, K.; Takahashi, M.; Fujimoto, K.; Shigematsu, N.; Sumii, T.; Okuyama, Y.

    2003-12-01

    Most of earthquakes in the crust occurred at the depth of 5 to 20km, and temperatures of 100 to 350° C. The physical properties of rocks at around these temperatures were determined by many frictional experiments. These results indicated the velocity dependence of steady state friction (a-b) was switched from velocity weakening ( seismic slip ) to velocity strengthening ( aseismic slip ) at around 350° C in the wet condition. In these experimental studies, granites were generally used. On the other hand, it is important to evaluate and to compare the physical properties of each mineral which composed of crustal rocks, for example feldspar and quartz, in order to understand the source processes of earthquakes in detail. In this study, we conducted frictional experiments by using albite, anorthite, and quartz gouges ( about 3μ m diameter ) under high pressure and high temperature in a triaxial apparatus, and compared frictional behaviors of three minerals with elevated temperature under the wet and dry conditions. These experiments were conducted by the velocity-stepping test. Temperature varied from room temperature to 600° C. In the dry conditions, experiments were conducted under the confining pressure of 150MPa. In the wet conditions, pore water pressure was applied up to 50MPa under the confining pressure of 200MPa. Sample was put between upper and lower sawcut alumina cylinders ( 20mm diameter x 40mm long ). The sawcut was oriented at 30° to the loading axis. These were jacketed with thin sleeves of annealed Cu. The values for a-b of quartz and albite were positive under the dry condition from room temperature to 600° C. On the other hand, those values of albite and quartz were negative at the temperature of 200° C and 300° C under the wet condition respectively. Those values of quartz decreased as the temperature increased from 100° C to 300° C and increased as the temperature increased from 300° C to 600° C. Those values of albite were switched

  4. Contribution of feldspar and marine organic aerosols to global ice nucleating particle concentrations

    Science.gov (United States)

    Vergara-Temprado, Jesús; Murray, Benjamin J.; Wilson, Theodore W.; O'Sullivan, Daniel; Browse, Jo; Pringle, Kirsty J.; Ardon-Dryer, Karin; Bertram, Allan K.; Burrows, Susannah M.; Ceburnis, Darius; DeMott, Paul J.; Mason, Ryan H.; O'Dowd, Colin D.; Rinaldi, Matteo; Carslaw, Ken S.

    2017-03-01

    Ice-nucleating particles (INPs) are known to affect the amount of ice in mixed-phase clouds, thereby influencing many of their properties. The atmospheric INP concentration changes by orders of magnitude from terrestrial to marine environments, which typically contain much lower concentrations. Many modelling studies use parameterizations for heterogeneous ice nucleation and cloud ice processes that do not account for this difference because they were developed based on INP measurements made predominantly in terrestrial environments without considering the aerosol composition. Errors in the assumed INP concentration will influence the simulated amount of ice in mixed-phase clouds, leading to errors in top-of-atmosphere radiative flux and ultimately the climate sensitivity of the model. Here we develop a global model of INP concentrations relevant for mixed-phase clouds based on laboratory and field measurements of ice nucleation by K-feldspar (an ice-active component of desert dust) and marine organic aerosols (from sea spray). The simulated global distribution of INP concentrations based on these two species agrees much better with currently available ambient measurements than when INP concentrations are assumed to depend only on temperature or particle size. Underestimation of INP concentrations in some terrestrial locations may be due to the neglect of INPs from other terrestrial sources. Our model indicates that, on a monthly average basis, desert dusts dominate the contribution to the INP population over much of the world, but marine organics become increasingly important over remote oceans and they dominate over the Southern Ocean. However, day-to-day variability is important. Because desert dust aerosol tends to be sporadic, marine organic aerosols dominate the INP population on many days per month over much of the mid- and high-latitude Northern Hemisphere. This study advances our understanding of which aerosol species need to be included in order to

  5. Contribution of feldspar and marine organic aerosols to global ice nucleating particle concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Vergara-Temprado, Jesús; Murray, Benjamin J.; Wilson, Theodore W.; O& amp; apos; Sullivan, Daniel; Browse, Jo; Pringle, Kirsty J.; Ardon-Dryer, Karin; Bertram, Allan K.; Burrows, Susannah M.; Ceburnis, Darius; DeMott, Paul J.; Mason, Ryan H.; O& amp; apos; Dowd, Colin D.; Rinaldi, Matteo; Carslaw, Ken S.

    2017-01-01

    Ice-nucleating particles (INPs) are known to affect the amount of ice in mixed-phase clouds, thereby influencing many of their properties. The atmospheric INP concentration changes by orders of magnitude from terrestrial to marine environments, which typically contain much lower concentrations. Many modelling studies use parameterizations for heterogeneous ice nucleation and cloud ice processes that do not account for this difference because they were developed based on INP measurements made predominantly in terrestrial environments without considering the aerosol composition. Errors in the assumed INP concentration will influence the simulated amount of ice in mixed-phase clouds, leading to errors in top-of-atmosphere radiative flux and ultimately the climate sensitivity of the model. Here we develop a global model of INP concentrations relevant for mixed-phase clouds based on laboratory and field measurements of ice nucleation by K-feldspar (an ice-active component of desert dust) and marine organic aerosols (from sea spray). The simulated global distribution of INP concentrations based on these two species agrees much better with currently available ambient measurements than when INP concentrations are assumed to depend only on temperature or particle size. Underestimation of INP concentrations in some terrestrial locations may be due to the neglect of INPs from other terrestrial sources. Our model indicates that, on a monthly average basis, desert dusts dominate the contribution to the INP population over much of the world, but marine organics become increasingly important over remote oceans and they dominate over the Southern Ocean. However, day-to-day variability is important. Because desert dust aerosol tends to be sporadic, marine organic aerosols dominate the INP population on many days per month over much of the mid- and high-latitude Northern Hemisphere. This study advances our understanding of which aerosol species need to be included in order to

  6. (abstract) Fundamental Mechanisms of Electrode Kinetics and Alkali Metal Atom Transport at the Alkali Beta'-Alumina/Porous Electrode/Alkali Metal Vapor Three Phase Boundary

    Science.gov (United States)

    Williams, R. M.; Jeffries-Nakamura, B.; Ryan, M. A.; Underwood, M. L.; O'Connor, D.; Kisor, A.; Kikkert, S. K.

    1993-01-01

    The mechanisms of electrode kinetics and mass transport of alkali metal oxidation and alkali metal cation reduction at the solid electrolyte/porous electrode boundary as well as alkali metal transport through porous metal electrodes has important applications in optimizing device performance in alkali metal thermal to electric converter (AMTEC) cells which are high temperature, high current density electrochemical cells. Basic studies of these processes also affords the opportunity to investigate a very basic electrochemical reaction over a wide range of conditions; and a variety of mass transport modes at high temperatures via electrochemical techniques. The temperature range of these investigations covers 700K to 1240K; the alkali metal vapor pressures range from about 10(sup -2) to 10(sup 2) Pa; and electrodes studied have included Mo, W, Mo/Na(sub 2)MoO(sub 4), W/Na(sub 2)WO(sub 4), WPt(sub x), and WRh(sub x) (1.0 alkali metal vapor and alkali metal vapor/solid electrolyte/vapor cells have been used to characterize the reaction and transport processes. We have previously reported evidence of ionic, free molecular flow, and surface transport of sodium in several types of AMTEC electrodes.

  7. Filling material for a buried cavity in a collapse area using light-weighted foam and active feldspar

    Science.gov (United States)

    Cho, Jin Woo; Lee, Ju-hyoung; Kim, Sung-Wook; Choi, Eun-Kyeong

    2017-04-01

    Concrete which is generally used as filling material for a buried cavity has very high strength but significantly high self-load is considered its disadvantage. If it is used as filling material, the second collapse due to additional load, causing irreversible damage. If light-weighted foam and active feldspar are used to solve this problem, the second collapse can be prevented by reducing of self-load of filling material. In this study, the specimen was produced by mixing light-weighted foam, active feldspar and cement, and changes in the density, unconfined compressive strength and hydraulic conductivity were analyzed. Using the light-weighted foam could enable the adjustment of density of specimen between 0.5 g/cm3 and 1.7 g/cm3, and if the mixing ratio of the light-weighted foam increases, the specimen has more pores and smaller range of cross-sectional area. It is confirmed that it has direct correlation with the density, and if the specimen has more pores, the density of the specimen is lowered. The density of the specimen influences the unconfined compressive strength and the hydraulic conductivity, and it was also confirmed that the unconfined compressive strength could be adjusted between 0.6 MPa and 8 MPa and the hydraulic conductivity could be adjusted between 10-9cm/sec and 10-3cm/sec. These results indicated that we can adjust unconfined compressive strength and hydraulic conductivity of filling materials by changing the mixing amount of lightweight-weighted foam according to the requirements of the field condition. Keywords: filling material, buried cavity, light-weighted foam, feldspar Acknowledgement This research was supported by a Grant from a Strategic Research Project (Horizontal Drilling and Stabilization Technologies for Urban Search and Rescue (US&R) Operation) funded by the Korea Institute of Civil Engineering and Building Technology.

  8. Conduction bands and invariant energy gaps in alkali bromides

    NARCIS (Netherlands)

    Boer, P.K. de; Groot, R.A. de

    1998-01-01

    Electronic structure calculations of the alkali bromides LiBr, NaBr, KBr, RbBr and CsBr are reported. It is shown that the conduction band has primarily bromine character. The size of the band gaps of bromides and alkali halides in general is reinterpreted.

  9. High-Order Dispersion Coefficients for Alkali-metal Atoms

    Institute of Scientific and Technical Information of China (English)

    KANG Shuai; DING Chi-Kun; CHEN Chang-Yong; WU Xue-Qing

    2013-01-01

    High-order dispersion coefficients C9,C11,C12,and C13 for the ground-state alkali-metals were calculated by combining the l-dependent model potential of alkali-metal atoms and linear variation method based on B-spline basis functions.The results were compared.

  10. Laser Spectroscopy of bi-alkali molecules

    Science.gov (United States)

    Dutta, Sourav; Altaf, A.; Lorenz, J.; Elliott, D.; Chen, Yong

    2010-03-01

    We report a study of laser spectroscopy of bi-alkali molecules, such as Li2, Rb2 and LiRb (work is in progress). We have constructed a dual-species (Li/Rb) heat pipe oven with a side viewport. The molecular fluorescence is excited by a dye laser with Rh6G dye (operating between 564 nm and 610 nm) and various home-made diode lasers (operating near 635 nm and 665 nm). The fluorescence is recorded using a .5ex1 -.1em/ -.15em.25ex4 m monochromator with a 0.1 nm (˜ 3 cm-1) spectral resolution. Transitions to the X^1σg^+ in Li2 and Rb2 have been measured and studies on LiRb are in progress. Molecular parameters, such as force constant, may be obtained from the analysis of the data (which agree with previously known values to within ˜ 3%). Using the known values of dissociation energy De and harmonic frequency φe for the alkali dimers, we also demonstrate that simple calculations with Morse potential approximation can be used to estimate the molecular transition wavelengths to within a few (1-3) nanometers from the experimentally measured values. Such information will aid in creating cold molecules via photoassociation in a dual species magneto-optical trap (LiRb in our case).

  11. Durability of Alkali Activated Blast Furnace Slag

    Science.gov (United States)

    Ellis, K.; Alharbi, N.; Matheu, P. S.; Varela, B.; Hailstone, R.

    2015-11-01

    The alkali activation of blast furnace slag has the potential to reduce the environmental impact of cementitious materials and to be applied in geographic zones where weather is a factor that negatively affects performance of materials based on Ordinary Portland Cement. The scientific literature provides many examples of alkali activated slag with high compressive strengths; however research into the durability and resistance to aggressive environments is still necessary for applications in harsh weather conditions. In this study two design mixes of blast furnace slag with mine tailings were activated with a potassium based solution. The design mixes were characterized by scanning electron microscopy, BET analysis and compressive strength testing. Freeze-thaw testing up to 100 freeze-thaw cycles was performed in 10% road salt solution. Our findings included compressive strength of up to 100 MPa after 28 days of curing and 120 MPa after freeze-thaw testing. The relationship between pore size, compressive strength, and compressive strength after freeze-thaw was explored.

  12. Pathways of birnessite formation in alkali medium

    Institute of Scientific and Technical Information of China (English)

    FENG Xionghan; TAN Wenfeng; LIU Fan; HUANG Qiaoyun; LIU Xiangwen

    2005-01-01

    Birnessite is a common weathering and oxidation product of manganese-bearing rocks. An O2 oxidation procedure of Mn(OH)2 in the alkali medium has been used to synthesize birnessite. Fast and powder X-ray diffraction (XRD), transmission electron microscopy (TEM), electron diffraction (ED), energy dispersed X-ray analysis (EDAX), infrared spectroscopy (IR) techniques and chemical composition analysis, Eh-pH equilibrium diagram approaches were employed to investigate the reaction process and pathways of birnessite formation. Results showed that the process of the birnessite formation could be divided into four stages: (1) formation stage for hausmannite and feitknechtite, (2) stage of transformation of hausmannite and feitknechtite to buserite, (3) buserite crystal growing stage, and (4) stage of conversion of buserite into birnessite. Mn(OH)2 was mainly present as amorphous state only for a short initial time of oxidation reaction. In the oxidation process, buserite formed following two pathways by recrystallization after dissolution of the intermediates, and the transformations of the minerals depended on the Eh determined by the dissolved O2 concentration on their surfaces. The results are fundamental in further exploration on the mechanism of birnessite formation in the alkali medium. A great practical significance would also be expected with respect to the areas of material sciences.

  13. Late Paleozoic deformation and exhumation in the Sierras Pampeanas (Argentina): 40Ar/39Ar-feldspar dating constraints

    Science.gov (United States)

    Löbens, Stefan; Oriolo, Sebastián; Benowitz, Jeff; Wemmer, Klaus; Layer, Paul; Siegesmund, Siegfried

    2016-09-01

    Systematic 40Ar/39Ar feldspar data obtained from the Sierras Pampeanas are presented, filling the gap between available high- (>~300 °C) and low-temperature (Pie de Palo regions, whereas the Sierras de San Luis and the Sierra de Comechingones regions record exhumation during the Carboniferous. Comparison between new and available data points to a Carboniferous tectonic event in the Sierras Pampeanas, which represents a key period to constrain the early evolution of the proto-Andean margin of Gondwana. This event was probably transtensional and played a major role during the evolution of the Paganzo Basin as well as during the emplacement of alkaline magmatism in the retroarc.

  14. Alkali and heavy metal emissions of the PCFB-process; Alkalipaeaestoet PCFB-prosessissa

    Energy Technology Data Exchange (ETDEWEB)

    Kuivalainen, R.; Eriksson, T.; Lehtonen, P. [Foster Wheeler Energia Oy, Karhula (Finland)

    1996-12-01

    Pressurized Circulating Fluidized Bed (PCFB) combustion technology has been developed in Karhula R and D Center since 1986. As a part of the development, 10 MW PCFB Test Facility was built in 1989. The Test Facility has been used for performance testing with different coal types through the years 1990-1995 in order to gain data for design and commercialization of the high-efficiency low-emission PCFB combustion technology. The project Y44 `Alkali and heavy metal emissions of the PCFB-process` was part of national LIEKKI 2 research program. The main object of the project was to measure vapor phase Na and K concentrations in the PCFB flue gas after hot gas filter and investigate the effects of process conditions and sorbents on alkali release. The measurements were performed using plasma assisted method by TUT Laboratory of Plasma Technology and wet absorption method of VTT Energy. The measured Na concentrations were below 30 ppb(w) in all measured data points. The results of K were below 10 ppb(w). The accuracies of the both methods are about + 50 % at this concentration range. The scatter of the data covers the effects of different process variables on the alkali emission. The measured emissions are at the same order of magnitude as the guideline emission limits estimated by gas turbine manufacturers. The measurements and development of the analyses methods are planned to be continued during PCFB test runs in spring 1996 for example within Joule II research program. (author)

  15. IRMPD Action Spectroscopy of Alkali Metal Cation-Cytosine Complexes: Effects of Alkali Metal Cation Size on Gas Phase Conformation

    NARCIS (Netherlands)

    Yang, B.; Wu, R.R.; Polfer, N.C.; Berden, G.; Oomens, J.; Rodgers, M.T.

    2013-01-01

    The gas-phase structures of alkali metal cation-cytosine complexes generated by electrospray ionization are probed via infrared multiple photon dissociation (IRMPD) action spectroscopy and theoretical calculations. IRMPD action spectra of five alkali metal cation-cytosine complexes exhibit both simi

  16. Albite feldspar dissolution kinetics as a function of the Gibbs free energy at high pCO_2

    CERN Document Server

    Hellmann, Roland; Tisserand, Delphine; Renard, François

    2008-01-01

    We are currently measuring the dissolution kinetics of albite feldspar at 100 deg C in the presence of high levels of dissolved CO_2 (pCO_2 = 9 MPa) as a function of the saturation state of the feldspar (Gibbs free energy of reaction, \\Delta G). The experiments are conducted using a flow through reactor, thereby allowing the dissolution reactions to occur at a fixed pH and at constant, but variable saturation states. Preliminary results indicate that at far-from-equilibrium conditions, the dissolution kinetics of albite are defined by a rate plateau, with R \\approx 5.0 x 10^{-10} mol m^{-2} s^{-1} at -70 -40 kJ mol^{-1}, the rates decrease sharply, revealing a strong inverse relation between the dissolution rate and free energy. Based on the experiments carried out to date, the dissolution rate-free energy data correspond to a highly non-linear and sigmoidal relation, in accord with recent studies.

  17. Influence of diopside: feldspar ratio in ceramic reactions assessed by quantitative phase analysis (X-ray diffraction - Rietveld method)

    Energy Technology Data Exchange (ETDEWEB)

    Kuzmickas, L.; Andrade, F.R.D.; Szabo, G.A.J. [Universidade de Sao Paulo (IGc/USP), SP (Brazil). Inst. de Geociencias. Dept. de Mineralogia e Geotecnia; Motta, J.F.M.; Cabral Junior, M., E-mail: lukuzmickas@gmail.com, E-mail: dias@usp.br, E-mail: gajszabo@usp.b, E-mail: motta.jf@gmail.com, E-mail: marsis@ipt.br [Instituto de Pesquisas Tecnologicas (IPT), Sao Paulo, SP (Brazil). Secao de Recursos Minerais e Tecnologia Ceramica

    2013-04-15

    White ceramics were produced with raw mixtures prepared with varying proportions of diopside-rich rock (0 to 20 wt.%) and potassic feldspar (40 to 20 wt.%), and fixed proportions of kaolinite (40 wt.%) and quartz (20 wt.%), fired in a temperature range from 1170 to 1210 deg C. The phases identified in the experimental ceramics were quartz, anorthite, mullite and glass, and their relative mass proportions were determined by X-ray diffraction (Rietveld method). The addition of diopside as a partial substitute for potassic feldspar causes the formation of a calcium silicate, analogous of the natural anorthite (CaSi{sub 2}Al{sub 2}O{sub 8}) in the ceramics, with proportional reduction in its glass and mullite contents. Water absorption and porosity of the ceramic bodies clearly decrease with increasing firing temperature, while the effect of the raw mixture composition on the physical and mechanical properties of the ceramics is less evident. Diopside-rich rock has low iron content (1.5 wt.% Fe{sub 2}O{sub 3}) and, therefore, promotes white burning. (author)

  18. Complex subvolcanic magma plumbing system of an alkali basaltic maar-diatreme volcano (Elie Ness, Fife, Scotland)

    Science.gov (United States)

    Gernon, T. M.; Upton, B. G. J.; Ugra, R.; Yücel, C.; Taylor, R. N.; Elliott, H.

    2016-11-01

    Alkali basaltic diatremes such as Elie Ness (Fife, Scotland) expose a range of volcanic lithofacies that points to a complex, multi-stage emplacement history. Here, basanites contain phenocrysts including pyrope garnet and sub-calcic augites from depths of 60 km. Volcanic rocks from all units, pyroclastic and hypabyssal, are characterised by rare earth element (REE) patterns that show continuous enrichment from heavy REE (HREE) to light REE (LREE), and high Zr/Y that are consistent with retention of garnet in the mantle source during melting of peridotite in a garnet lherzolite facies. Erupted garnets are euhedral and unresorbed, signifying rapid ascent through the lithosphere. The magmas also transported abundant pyroxenitic clasts, cognate with the basanite host, from shallower depths ( 35-40 km). These clasts exhibit wide variation in texture, mode and mineralogy, consistent with growth from a range of compositionally diverse melts. Further, clinopyroxene phenocrysts from both the hypabyssal and pyroclastic units exhibit a very wide compositional range, indicative of polybaric fractionation and magma mixing. This is attributed to stalling of earlier magmas in the lower crust - principally from 22 to 28 km - as indicated by pyroxene thermobarometry. Many clinopyroxenes display chemical zoning profiles, occasionally with mantles and rims of higher magnesium number (Mg#) suggesting the magmas were mobilised by juvenile basanite magma. The tuffs also contain alkali feldspar megacrysts together with Fe-clinopyroxene, zircon and related salic xenoliths, of the 'anorthoclasite suite' - inferred to have crystallised at upper mantle to lower crustal depths from salic magma in advance of the mafic host magmas. Despite evidence for entrainment of heterogeneous crystal mushes, the rapidly ascending melts experienced negligible crustal contamination. The complex association of phenocrysts, megacrysts and autoliths at Elie Ness indicates thorough mixing in a dynamic system

  19. Fission of Multiply Charged Alkali Clusters

    Science.gov (United States)

    Barnett, Robert N.; Yannouleas, Constantine; Landman, Uzi

    2001-03-01

    We use ab-initio molecular dynamics simulations to investigate the fission of multiply charged pure and mixed alkali clusters. Positive (+2 to +4) clusters of up to 30 atoms are considered. The clusters are initially equilibrated with a charge of +1 or +2 (depending on size) and at temperatures of 150 to 800 K. subsequently the clusters are further ionized and their evolution is followed. For doubly charged clusters binary fission occurs, while higher charged clusters fission through ternary or quaternary channels. The most common occurrence is the emission of a singly charged 3-atom cluster, which may occur repeatedly until the remaining cluster is stable. The dynamics of the fission process is discussed, and the results are compared with experiments and with the predictions of the liquid-drop and shell-corrected jellium models.

  20. Thermoluminescence of alkali halides and its implications

    Energy Technology Data Exchange (ETDEWEB)

    Gartia, R.K., E-mail: rkgartia02@yahoo.in [Physics Department, Manipur University, Imphal 795003 (India); Rey, L. [Aerial-CRT-parc d' Innovation, B.P. 40443, F-67412 Illkirch Cedex (France); Tejkumar Singh, Th. [Physics Department, Manipur University, Imphal 795003 (India); Basanta Singh, Th. [Luminescence Dating Laboratory, Manipur University, Imphal 795003 (India)

    2012-03-01

    Trapping levels present in some alkali halides namely NaCl, KCl, KBr, and KI are determined by deconvolution of the thermoluminescence (TL) curves. Unlike most of the studies undertaken over the last few decades, we have presented a comprehensive picture of the phenomenon of TL as an analytical technique capable of revealing the position of the trapping levels present in the materials. We show that for all practical purposes, TL can be described involving only the three key trapping parameters, namely, the activation energy (E), the frequency factor (s), and the order of kinetics (b) even for complex glow curves having a number of TL peaks. Finally, based on these, we logically infer the importance of TL in development and characterization of materials used in dosimetry, dating and scintillation.

  1. Alkali-activated cementitious materials: Mechanisms, microstructure and properties

    Science.gov (United States)

    Jiang, Weimin

    The goal of this study was to examine the activation reaction, microstructure, properties, identify the mechanisms of activation, and achieve an enhanced understanding of activation processes occurring during the synthesis of alkali activated cementitious materials (AAC). The discussions classify the following categories. (1) alkali activated slag cement; (2) alkali activated portland-slag cement; (3) alkali activated fly ash-slag cement; (4) alkali activated pozzolana-lime cement; (5) alkali activated pozzolana cement. The activators involved are NaOH, KOH; Nasb2SOsb4;\\ Nasb2COsb3;\\ CaSOsb4, and soluble silicate of sodium and potassium. The effect of alkali activation on the microstructure of these materials were analyzed at the micro-nanometer scale by SEM, EDS, ESEM, and TEM. Also sp{29}Si and sp{27}Al MAS-NMR, IR, Raman, TGA, and DTA were performed to characterize the phase in these systems. Slag, fly ash, silica fume, as well as blended cements containing mixtures of these and other components were characterized. A set of ordinary portland cement paste samples served as a control. This study confirmed that AAC materials have great potential because they could generate very early high strength, greater durability and high performance. Among the benefits to be derived from this research is a better understanding of the factors that control concrete properties when using AAC materials, and by controlling the chemistry and processing to produce desired microstructures and properties, as well as their durability.

  2. Controlled in-situ dissolution of an alkali metal

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Jeffrey Donald; Dooley, Kirk John; Tolman, David Donald

    2012-09-11

    A method for the controllable dissolution of one or more alkali metals from a vessel containing a one or more alkali metals and/or one or more partially passivated alkali metals. The vessel preferably comprising a sodium, NaK or other alkali metal-cooled nuclear reactor that has been used. The alkali metal, preferably sodium, potassium or a combination thereof, in the vessel is exposed to a treatment liquid, preferably an acidic liquid, more preferably citric acid. Preferably, the treatment liquid is maintained in continuous motion relative to any surface of unreacted alkali metal with which the treatment liquid is in contact. The treatment liquid is preferably pumped into the vessel containing the one or more alkali metals and the resulting fluid is extracted and optionally further processed. Preferably, the resulting off-gases are processed by an off-gas treatment system and the resulting liquids are processed by a liquid disposal system. In one preferred embodiment, an inert gas is pumped into the vessel along with the treatment liquid.

  3. Influence of alkalis from different sources than cement in the evolution of alkali-silica reaction

    Directory of Open Access Journals (Sweden)

    Olague, C.

    2003-12-01

    Full Text Available A bibliographical revision of the existent literature allows showing symptoms of alkali-silica reaction (ASR in highways, and the practical and economic method uranyl acetate to confirm the presence of ASR. The existence of reaction in concrete pavements of Chihuahua City was verified by a visual observation of patterns cracks, examination of gel deposits and the presence of reactive materials. Considering that the cement used to construct this pavements with problems of ASR, was low alkalis cement, the research was devoted to study the influence of alkalis coming from different sources than cement in the evolution of reaction such as: a aggregates: gravel and sand, b mix water, c additives and d minerals additions The initial classification of cements like high and low alkalis concerned to ASR must be revised for accept the fact that there is not a unique maximum limit alkalis of cement under which the expansible reactivity cannot occur.

    Una revisión bibliográfica de la literatura existente permite mostrar las manifestaciones de reacción álcali-sílice (RAS en estructuras de carreteras y el método práctico y económico de acetato de uranilo para confirmar la presencia de RAS. La existencia de la reacción en pavimentos de hormigón de la ciudad de Chihuahua se pudo confirmar tras la observación visual de modelos de grietas, estudios de depósitos de gel y existencia de fuentes de materiales reactivos. Considerando que el cemento utilizado para construir los tramos de pavimento con problemas de RAS, era un cemento bajo en álcalis, se enfocó la investigación al estudio de la influencia de los álcalis provenientes de fuentes distintas al cemento en la evolución de la reacción tales como: a áridos gruesos y finos, b agua de mezclado, c aditivos y d adiciones minerales El concepto inicial de clasificación de cementos altos y bajos en álcalis con respecto a la RAS debe ser revisado para aceptar el hecho de que no hay un solo

  4. Pi resonance of chemisorbed alkali atoms on noble metals.

    Science.gov (United States)

    Borisov, A G; Sametoglu, V; Winkelmann, A; Kubo, A; Pontius, N; Zhao, J; Silkin, V M; Gauyacq, J P; Chulkov, E V; Echenique, P M; Petek, H

    2008-12-31

    We have performed a joint experimental and theoretical study of the unoccupied electronic structure of alkali adsorbates on the (111) surfaces of Cu and Ag. Combining angle- and time-resolved two-photon photoemission spectroscopy with wave packet propagation calculations we show that, along with the well known sigma resonance oriented along the surface normal, there exist long-lived alkali-localized resonances oriented parallel to the surface (pi symmetry). These new resonances are stabilized by the projected band gap of the substrate and emerge primarily from the mixing of the p and d Rydberg orbitals of the free alkali atom modified by the interaction with the surface.

  5. Important role of alkali atoms in A4C60

    OpenAIRE

    Gunnarsson, O.; Erwin, S. C.; Koch, E.; Martin, R. M.

    1997-01-01

    We show that hopping via the alkali atoms plays an important role for the t1u band of A4C60 (A=K, Rb), in strong contrast to A3C60. Thus the t1u band is broadened by more than 40 % by the presence of the alkali atoms. The difference between A4C60 and A3C60 is in particular due to the less symmetric location of the alkali atoms in A4C60.

  6. Alkaline Rocks and Geodynamics

    OpenAIRE

    BONIN, Bernard

    1998-01-01

    Origin of A-type alkali feldspar granites is currently the subject of a world-wide debate. Contrasting hypotheses have been proposed, which range from an entirely crustal origin to an almost complete mantle derivation. A-type alkali feldspar granites belong to either unimodal granite (rhyolite)-dominated association, or bimodal gabbro (basalt)-granite (rhyolite) suite. It is argued that (i) the ultimate mantle origin of basic to intermediate rocks is beyond doubt, (ii) highly evolved felsi...

  7. Structural reliability of alumina-, feldspar-, leucite-, mica- and zirconia-based ceramics.

    Science.gov (United States)

    Tinschert, J; Zwez, D; Marx, R; Anusavice, K J

    2000-09-01

    The objective of this study was to test the hypothesis that industrially manufactured ceramic materials, such as Cerec Mark II and Zirconia-TZP, have a smaller range of fracture strength variation and therefore greater structural reliability than laboratory-processed dental ceramic materials. Thirty bar specimens per material were prepared and tested. The four-point bend test was used to determine the flexure strength of all ceramic materials. The fracture stress values were analyzed by Weibull analysis to determine the Weibull modulus values (m) and the 1 and 5% probabilities of failure. The mean strength and standard deviation values for these ceramics are as follows: (MPa+/-SD) were: Cerec Mark II, 86.3+/-4.3; Dicor, 70.3+/-12.2; In-Ceram Alumina, 429. 3+/-87.2; IPS Empress, 83.9+/-11.3; Vitadur Alpha Core, 131.0+/-9.5; Vitadur Alpha Dentin, 60.7+/-6.8; Vita VMK 68, 82.7+/-10.0; and Zirconia-TZP, 913.0+/-50.2. There was no statistically significant difference among the flexure strength of Cerec Mark II, Dicor, IPS Empress, Vitadur Alpha Dentin, and Vita VMK 68 ceramics (p>0.05). The highest Weibull moduli were associated with Cerec Mark II and Zirconia-TZP ceramics (23.6 and 18.4). Dicor glass-ceramic and In-Ceram Alumina had the lowest m values (5.5 and 5.7), whereas intermediate values were observed for IPS-Empress, Vita VMK 68, Vitadur Alpha Dentin and Vitadur Alpha Core ceramics (8.6, 8.9, 10.0 and 13.0, respectively). Except for In-Ceram Alumina, Vitadur Alpha and Zirconia-TZP core ceramics, most of the investigated ceramic materials fabricated under the condition of a dental laboratory were not stronger or more structurally reliable than Vita VMK 68 veneering porcelain. Only Cerec Mark II and Zirconia-TZP specimens, which were prepared from an industrially optimized ceramic material, exhibited m values greater than 18. Hence, we conclude that industrially prepared ceramics are more structurally reliable materials for dental applications although CAD

  8. Acid/alkali gated photochromism of two diarylperfluorocyclopentenes

    Institute of Scientific and Technical Information of China (English)

    CHEN; ZiHui; ZHAO; ShengMin; LI; ZhongYu; ZHANG; Zhi; ZHANG; FuShi

    2007-01-01

    Two novel diarylfuorocyclopentenes, which underwent gated photochromism, were synthesized. It was found that the photochromic property of these diarylethenes could be switched by alternative addition of acids/alkalis, which could provide a new design strategy toward chemical threshold photoreaction.

  9. Profiling application potential for alkali treated sisal fiber ...

    African Journals Online (AJOL)

    ATHARVA

    In this study, the cellulosic fiber sisal has been modified with alkali solution to impart ... The volume fraction also, has profound influence on fiber-matrix interface .... bonding due to incompatibility or poor surface wetting of hydrophilic fiber.

  10. Electric field-induced softening of alkali silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    McLaren, C.; Heffner, W.; Jain, H. [Department of Materials Science and Engineering, Lehigh University, Bethlehem, Pennsylvania 18015 (United States); Tessarollo, R.; Raj, R. [Department of Mechanical Engineering, University of Colorado at Boulder, Boulder, Colorado 80309 (United States)

    2015-11-02

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  11. Electric field-induced softening of alkali silicate glasses

    Science.gov (United States)

    McLaren, C.; Heffner, W.; Tessarollo, R.; Raj, R.; Jain, H.

    2015-11-01

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  12. Hall Determination of Atomic Radii of Alkali Metals

    Science.gov (United States)

    Houari, Ahmed

    2008-01-01

    I will propose here an alternative method for determining atomic radii of alkali metals based on the Hall measurements of their free electron densities and the knowledge of their crystal structure. (Contains 2 figures.)

  13. Structure and electronic properties of alkali-C60 nanoclusters.

    Science.gov (United States)

    Rabilloud, Franck

    2010-07-08

    I investigated the structural and electronic properties of both Na(n)C(60) and Li(n)C(60) (n alkali atoms over the C(60) surface is analyzed. The hypotheses for either an homogeneous coating of the C(60) surface by the alkali atoms or the growth of an alkali droplet not wetting the fullerene surface are discussed. Lithium atoms are found to coat homogeneously the fullerene on the C(60) surface via pentagonal sites, contrary to sodium atoms, which prefer to form 4-atom islands on the surface. The charge transfer, the energetics, and the dipole moments are discussed in relation with available results. The adsorption of alkali atoms on the C(60) surface considerably enhances the capacity of C(60) to accept electrons. The arrangement of lithium atoms seems more favorable for the hydrogen storage than that of sodium atoms.

  14. The 4843 Alkali Metal Storage Facility Closure Plan

    Energy Technology Data Exchange (ETDEWEB)

    1991-06-01

    The 4843 AMSF has been used primarily to provide a centralized building to receive and store dangerous and mixed alkali metal waste, including sodium and lithium, which has been generated at the Fast Flux Test Facility and at various other Hanford Site operations that used alkali metals. Most of the dangerous and mixed alkali metal waste received consists of retired equipment from liquid sodium processes. The unit continues to store material. In general, only solid alkali metal waste that is water reactive is stored at the 4843 AMSF. The 4843 AMSF will be closed in a manner consistent with Ecology guidelines and regulations (WAC 173-303-610). The general closure procedure is detailed as follows.

  15. Crystal-chemical controls on the partitioning of Sr and Ba between plagioclase feldspar, silicate melts, and hydrothermal solutions

    Energy Technology Data Exchange (ETDEWEB)

    Blundy, J.D.; Wood, B.J. (Bristol Univ. (England))

    1991-01-01

    The aim of this paper is to evaluate the factors which control the partitioning of alkaline earth elements (Ba and Sr) between plagioclase feldspar and silicate melts, specifically the respective role of crystal chemistry, melt chemistry, and temperature. We have selected plagioclase because of the wealth of volcanic and experimental data, the compositional simplicity of plagioclase, and its relevance to many petrological problems. We begin our study by examining experimental data on Sr partitioning between plagioclase and hydrothermal solutions in an attempt to constrain the role of crystal chemistry. We establish a simple thermodynamic model for trace element partitioning between plagioclase and hydrothermal solutions. This treatment is then extended to the plagioclase-melt system using available data from both experimental and volcanic systems in order to derive a general equation for Sr and Ba partitioning. Finally we consider the geochemical applications and implications of our findings.

  16. Late Paleozoic deformation and exhumation in the Sierras Pampeanas (Argentina): 40Ar/39Ar-feldspar dating constraints

    Science.gov (United States)

    Löbens, Stefan; Oriolo, Sebastián; Benowitz, Jeff; Wemmer, Klaus; Layer, Paul; Siegesmund, Siegfried

    2017-09-01

    Systematic 40Ar/39Ar feldspar data obtained from the Sierras Pampeanas are presented, filling the gap between available high- (> 300 °C) and low-temperature (< 150 °C) thermochronological data. Results show Silurian-Devonian exhumation related to the late stages of the Famatinian/Ocloyic Orogeny for the Sierra de Pocho and the Sierra de Pie de Palo regions, whereas the Sierras de San Luis and the Sierra de Comechingones regions record exhumation during the Carboniferous. Comparison between new and available data points to a Carboniferous tectonic event in the Sierras Pampeanas, which represents a key period to constrain the early evolution of the proto-Andean margin of Gondwana. This event was probably transtensional and played a major role during the evolution of the Paganzo Basin as well as during the emplacement of alkaline magmatism in the retroarc.

  17. Sorption of environmentally relevant radionuclides (U(VI), Np(V)) and lanthanides (Nd(III)) on feldspar and mica

    Energy Technology Data Exchange (ETDEWEB)

    Richter, Constanze

    2015-11-05

    A safe storage of radioactive waste in repositories is an important task to protect humans and the environment from radio- and chemotoxicity. Long-term safety assessments predict the behavior of potential environmental contaminants like the actinides plutonium, uranium, or neptunium, in the near and far field of repositories. For such safety assessments, it is necessary to know the migration behavior of the contaminants in the environment, which is mainly dependent on the aquatic speciation, the solubility product of relevant solid phases, and the retardation due to sorption on surrounding minerals. Thus, an investigation of sorption processes of contaminants onto different minerals as well as the derivation of mineral specific surface complexation model (SCM) parameters is of great importance. Feldspar and mica are widely distributed in nature. They occur as components of granite, which is considered as a potential host rock for a repository in Germany, and in numerous other rocks, and thus also in the far field of nearly all repositories. However, their sorption behavior with actinides has only been scarcely investigated until now. In order to better characterize these systems and subsequently to integrate these minerals into the long-term safety assessments, this work focuses on the investigation of the sorption behavior of U(VI), Np(V), and Nd(III) as analogue for An(III) onto the minerals orthoclase and muscovite, representing feldspars and mica, respectively. All investigations were performed under conditions relevant to the far field of a repository. In addition to the extensive characterization of the minerals, batch sorption experiments, spectroscopic investigations, and surface complexation modeling were performed to elucidate the uptake and speciation of actinides on the mineral surfaces. In addition, the influence of microorganisms naturally occurring on the mineral surfaces and the effect of Ca{sup 2+} on U(VI) uptake on the minerals was studied. The

  18. Alkali absorption and citrate excretion in calcium nephrolithiasis

    Science.gov (United States)

    Sakhaee, K.; Williams, R. H.; Oh, M. S.; Padalino, P.; Adams-Huet, B.; Whitson, P.; Pak, C. Y.

    1993-01-01

    The role of net gastrointestinal (GI) alkali absorption in the development of hypocitraturia was investigated. The net GI absorption of alkali was estimated from the difference between simple urinary cations (Ca, Mg, Na, and K) and anions (Cl and P). In 131 normal subjects, the 24 h urinary citrate was positively correlated with the net GI absorption of alkali (r = 0.49, p < 0.001). In 11 patients with distal renal tubular acidosis (RTA), urinary citrate excretion was subnormal relative to net GI alkali absorption, with data from most patients residing outside the 95% confidence ellipse described for normal subjects. However, the normal relationship between urinary citrate and net absorbed alkali was maintained in 11 patients with chronic diarrheal syndrome (CDS) and in 124 stone-forming patients devoid of RTA or CDS, half of whom had "idiopathic" hypocitraturia. The 18 stone-forming patients without RTA or CDS received potassium citrate (30-60 mEq/day). Both urinary citrate and net GI alkali absorption increased, yielding a significantly positive correlation (r = 0.62, p < 0.0001), with the slope indistinguishable from that of normal subjects. Thus, urinary citrate was normally dependent on the net GI absorption of alkali. This dependence was less marked in RTA, confirming the renal origin of hypocitraturia. However, the normal dependence was maintained in CDS and in idiopathic hypocitraturia, suggesting that reduced citrate excretion was largely dietary in origin as a result of low net alkali absorption (from a probable relative deficiency of vegetables and fruits or a relative excess of animal proteins).

  19. Alkali promotion of N-2 dissociation over Ru(0001)

    DEFF Research Database (Denmark)

    Mortensen, Jens Jørgen; Hammer, Bjørk; Nørskov, Jens Kehlet

    1998-01-01

    Using self-consistent density functional calculations, we show that adsorbed Na and Cs lower the barrier for dissociation of N2 on Ru(0001). Since N2 dissociation is a crucial step in the ammonia synthesis reaction, we explain in this way the experimental observation that alkali metals promote th...... the ammonia synthesis reaction over Ru catalysts. We also show that the origin of this effect is predominantly a direct electrostatic attraction between the adsorbed alkali atoms and the dissociating molecule....

  20. Photoemission spectroscopy study of a multi-alkali photocathode

    CERN Document Server

    Ettema, A R H

    2000-01-01

    In this paper a photoemission study of the highest core levels of the elements and the electron escape barrier (work function) in a multi-alkali photocathode are presented. The core levels indicate that the alkali atoms are in an oxidized state and therefore the compound Na sub 2 KSb can be regarded as an ionic semiconductor. The measured escape barrier of the Cs sub 2 O surface layer is determined as 2.3 eV.

  1. Near atomically smooth alkali antimonide photocathode thin films

    CERN Document Server

    Feng, Jun; Nasiatka, James; Schubert, Susanne; Smedley, John; Padmore, Howard

    2016-01-01

    Nano-roughness limits the emittance of electron beams that can be generated by high efficiency photocathodes, such as the thermally reacted alkali antimonide thin films. However there is an urgent need for photocathodes that can produce an order of magnitude or more lower emittance than present day systems in order to increase the transverse coherence width of the electron beam. In this paper we demonstrate a method for producing alkali antimonide cathodes with near atomic smoothness with high reproducibility.

  2. Estimating the hydration enthalpies of neutral alkali metal atoms.

    Science.gov (United States)

    Stace, A J

    2006-10-26

    Using existing data on the ionization energies of alkali metal atoms in small clusters of water, a thermodynamic cycle is proposed from which the hydration enthalpies of the neutral metal atoms can be estimated. Where comparisons are possible, the results are in reasonable agreement with those obtained using both experimental and ab initio methods. Application of the thermodynamic cycle to neutral alkali metal atoms solvated in ammonia yields solvation enthalpies that are significantly lower than those obtained for water.

  3. Two-phase alkali-metal experiments in reduced gravity

    Energy Technology Data Exchange (ETDEWEB)

    Antoniak, Z.I.

    1986-06-01

    Future space missions envision the use of large nuclear reactors utilizing either a single or a two-phase alkali-metal working fluid. The design and analysis of such reactors require state-of-the-art computer codes that can properly treat alkali-metal flow and heat transfer in a reduced-gravity environment. A literature search of relevant experiments in reduced gravity is reported on here, and reveals a paucity of data for such correlations. The few ongoing experiments in reduced gravity are noted. General plans are put forth for the reduced-gravity experiments which will have to be performed, at NASA facilities, with benign fluids. A similar situation exists regarding two-phase alkali-metal flow and heat transfer, even in normal gravity. Existing data are conflicting and indequate for the task of modeling a space reactor using a two-phase alkali-metal coolant. The major features of past experiments are described here. Data from the reduced-gravity experiments with innocuous fluids are to be combined with normal gravity data from the two-phase alkali-metal experiments. Analyses undertaken here give every expectation that the correlations developed from this data base will provide a valid representation of alkali-metal heat transfer and pressure drop in reduced gravity.

  4. Vibrations of alkali metal overlayers on metal surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rusina, G G; Eremeev, S V; Borisova, S D [Institute of Strength Physics and Materials Science SB RAS, 634021, Tomsk (Russian Federation); Echenique, P M; Chulkov, E V [Donostia International Physics Center (DIPC), 20018 San Sebastian/Donostia, Basque Country (Spain); Benedek, G [Dipartimento di Scienza dei Materiali, Universita di Milano-Bicocca, Via Cozzi 53, 20125 Milano (Italy)], E-mail: rusina@ispms.tsc.ru

    2008-06-04

    We review the current progress in the understanding of vibrations of alkalis adsorbed on metal surfaces. The analysis of alkali vibrations was made on the basis of available theoretical and experimental results. We also include in this discussion our recent calculations of vibrations in K/Pt(111) and Li(Na)/Cu(001) systems. The dependence of alkali adlayer localized modes on atomic mass, adsorption position and coverage as well as the dependence of vertical vibration frequency on the substrate orientation is discussed. The square root of atomic mass dependence of the vertical vibration energy has been confirmed by using computational data for alkalis on the Al(111) and Cu(001) substrates. We have confirmed that in a wide range of submonolayer coverages the stretch mode energy remains nearly constant while the energy of in-plane polarized modes increases with the increase of alkali coverage. It was shown that the spectrum of both stretch and in-plane vibrations can be very sensitive to the adsorption position of alkali atoms and substrate orientation.

  5. Vibrations of alkali metal overlayers on metal surfaces

    Science.gov (United States)

    Rusina, G. G.; Eremeev, S. V.; Echenique, P. M.; Benedek, G.; Borisova, S. D.; Chulkov, E. V.

    2008-06-01

    We review the current progress in the understanding of vibrations of alkalis adsorbed on metal surfaces. The analysis of alkali vibrations was made on the basis of available theoretical and experimental results. We also include in this discussion our recent calculations of vibrations in K/Pt(111) and Li(Na)/Cu(001) systems. The dependence of alkali adlayer localized modes on atomic mass, adsorption position and coverage as well as the dependence of vertical vibration frequency on the substrate orientation is discussed. The square root of atomic mass dependence of the vertical vibration energy has been confirmed by using computational data for alkalis on the Al(111) and Cu(001) substrates. We have confirmed that in a wide range of submonolayer coverages the stretch mode energy remains nearly constant while the energy of in-plane polarized modes increases with the increase of alkali coverage. It was shown that the spectrum of both stretch and in-plane vibrations can be very sensitive to the adsorption position of alkali atoms and substrate orientation.

  6. CHEMICAL AND THERMAL STABILITY OF RICE HUSKS AGAINST ALKALI TREATMENT

    Directory of Open Access Journals (Sweden)

    Bwire S. Ndazi

    2008-11-01

    Full Text Available Chemical and thermal stability of rice husks against alkali treatment with 2 to 8% w/v NaOH are presented and discussed in this paper. The thermal stability of the rice husks was examined by using a thermal gravimetric analysis instrument. Chemical stability was evaluated by examining the organic components of rice husks using proximate analysis. The results indicated that the proportion of lignin and hemicellulose in rice husks treated with NaOH ranging from 4 to 8% decreased significantly by 96% and 74%, respectively. The thermal stability and final degradation temperatures of the alkali-treated rice husks were also lowered by 24-26°C due to degradation of hemicellulose and lignin during alkali treatment. Absence of the onset degradation zones in the alkali-treated rice husks was a further indication that hemicellulose and other volatile substances degraded during alkali treatment. This leads to a conclusion that alkali treatment of rice husks with more than 4% NaOH causes a substantial chemical degradation of rice husks, which subsequently decreases their thermal stability.

  7. Absorption spectra of alkali-C₆₀ nanoclusters.

    Science.gov (United States)

    Rabilloud, Franck

    2014-10-28

    We investigate the absorption spectra of alkali-doped C60 nanoclusters, namely C60Nan, C60Kn, and C60Lin, with n = 1, 2, 6, 12, in the framework of the time-dependent density-functional theory (TDDFT). We study the dependence of the absorption spectra on the nature of the alkali. We show that in few cases the absorption spectra depend on the arrangement of the alkali atoms over the fullerene, though sometimes the absorption spectra do not allow us to distinguish between different configurations. When only one or two alkali atoms are adsorbed on the fullerene, the optical response of alkali-doped C60 is similar to that of the anion C60(-) with a strong response in the UV domain. In contrast, for higher concentration of alkali, a strong optical response is predicted in the visible range, particularly when metal-metal bonds are formed. The weak optical response of the I(h)-symmetry C60Li12 is proposed to be used as a signature of its structure.

  8. Alkali-metal azides interacting with metal-organic frameworks.

    Science.gov (United States)

    Armata, Nerina; Cortese, Remedios; Duca, Dario; Triolo, Roberto

    2013-01-14

    Interactions between alkali-metal azides and metal-organic framework (MOF) derivatives, namely, the first and third members of the isoreticular MOF (IRMOF) family, IRMOF-1 and IRMOF-3, are studied within the density functional theory (DFT) paradigm. The investigations take into account different models of the selected IRMOFs. The mutual influence between the alkali-metal azides and the π rings or Zn centers of the involved MOF derivatives are studied by considering the interactions both of the alkali-metal cations with model aromatic centers and of the alkali-metal azides with distinct sites of differently sized models of IRMOF-1 and IRMOF-3. Several exchange and correlation functionals are employed to calculate the corresponding interaction energies. Remarkably, it is found that, with increasing alkali-metal atom size, the latter decrease for cations interacting with the π-ring systems and increase for the azides interacting with the MOF fragments. The opposite behavior is explained by stabilization effects on the azide moieties and determined by the Zn atoms, which constitute the inorganic vertices of the IRMOF species. Larger cations can, in fact, coordinate more efficiently to both the aromatic center and the azide anion, and thus stabilizing bridging arrangements of the azide between one alkali-metal and two Zn atoms in an η(2) coordination mode are more favored.

  9. Alkali and heavy metal emissions of the PCFB-process; Alkali- ja raskasmetallipaeaestoet PCFB-prosessista

    Energy Technology Data Exchange (ETDEWEB)

    Kuivalainen, R.; Eriksson, T.; Lehtonen, P. [Foster Wheeler Energia Oy, Karhula (Finland)

    1997-10-01

    Pressurized Circulating Fluidized Bed (PCFB) combustion technology has been developed in Karhula R and D Center since 1986. As part of the development, 10 MW PCFB test facility was built in 1989. The test facility has been used for performance testing with different coal types through the years 1990-1995 in order to gain data for design and commercialization of the high-efficiency low-emission PCFB combustion technology. The main object of the project was to measure vapor phase Na and K concentrations in the PCFB flue gas after hot gas filter and investigate the effects of process conditions and sorbents on alkali release. The measurements were performed using plasma assisted method of TUT Laboratory of Plasma Technology and wet absorption method of VTT Energy. The measurements were carried out during three test campaigns at PCFB Test Facility in Karhula. In autumn 1995 both VTT and TUT methods were used. The measurements of the following test period in spring 1996 were performed by VTT, and during the last test segment in autumn 1996 TUT method was in use. During the last test period, the TUT instrument was used as semi-continuous (3 values/minute) alkali analyzer for part of the time. The measured Na concentrations were below 30 ppb(w) in all measured data points. The results of K were below 10 ppb(w). The accuracies of the both methods are about +50 % at this concentration range. The scatter of the data covers the effects of different process variables on the alkali emission. The measured emissions are at the same order of magnitude as the guideline emission limits estimated by gas turbine manufacturers

  10. Relation between the electroforming voltage in alkali halide-polymer diodes and the bandgap of the alkali halide

    Energy Technology Data Exchange (ETDEWEB)

    Bory, Benjamin F.; Wang, Jingxin; Janssen, René A. J.; Meskers, Stefan C. J., E-mail: s.c.j.meskers@tue.nl [Molecular Materials and Nanosystems and Institute for Complex Molecular Systems, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands); Gomes, Henrique L. [Instituto de Telecomunicações, Av. Rovisco, Pais 1, 1049-001 Lisboa, Portugal and Universidade do Algarve, Campus de Gambelas, 8005-139 Faro (Portugal); De Leeuw, Dago M. [Max-Planck Institute for Polymer Research, Ackermannweg 10, 55128 Mainz, Germany and King Abdulaziz University, Jeddah (Saudi Arabia)

    2014-12-08

    Electroforming of indium-tin-oxide/alkali halide/poly(spirofluorene)/Ba/Al diodes has been investigated by bias dependent reflectivity measurements. The threshold voltages for electrocoloration and electroforming are independent of layer thickness and correlate with the bandgap of the alkali halide. We argue that the origin is voltage induced defect formation. Frenkel defect pairs are formed by electron–hole recombination in the alkali halide. This self-accelerating process mitigates injection barriers. The dynamic junction formation is compared to that of a light emitting electrochemical cell. A critical defect density for electroforming is 10{sup 25}/m{sup 3}. The electroformed alkali halide layer can be considered as a highly doped semiconductor with metallic transport characteristics.

  11. Bioinorganic Chemistry of the Alkali Metal Ions.

    Science.gov (United States)

    Kim, Youngsam; Nguyen, Thuy-Tien T; Churchill, David G

    2016-01-01

    The common Group 1 alkali metals are indeed ubiquitous on earth, in the oceans and in biological systems. In this introductory chapter, concepts involving aqueous chemistry and aspects of general coordination chemistry and oxygen atom donor chemistry are introduced. Also, there are nuclear isotopes of importance. A general discussion of Group 1 begins from the prevalence of the ions, and from a comparison of their ionic radii and ionization energies. While oxygen and water molecule binding have the most relevance to biology and in forming a detailed understanding between the elements, there is a wide range of basic chemistry that is potentially important, especially with respect to biological chelation and synthetic multi-dentate ligand design. The elements are widely distributed in life forms, in the terrestrial environment and in the oceans. The details about the workings in animal, as well as plant life are presented in this volume. Important biometallic aspects of human health and medicine are introduced as well. Seeing as the elements are widely present in biology, various particular endogenous molecules and enzymatic systems can be studied. Sodium and potassium are by far the most important and central elements for consideration. Aspects of lithium, rubidium, cesium and francium chemistry are also included; they help in making important comparisons related to the coordination chemistry of Na(+) and K(+). Physical methods are also introduced.

  12. Superconductivity in alkali-metal-doped picene.

    Science.gov (United States)

    Mitsuhashi, Ryoji; Suzuki, Yuta; Yamanari, Yusuke; Mitamura, Hiroki; Kambe, Takashi; Ikeda, Naoshi; Okamoto, Hideki; Fujiwara, Akihiko; Yamaji, Minoru; Kawasaki, Naoko; Maniwa, Yutaka; Kubozono, Yoshihiro

    2010-03-04

    Efforts to identify and develop new superconducting materials continue apace, motivated by both fundamental science and the prospects for application. For example, several new superconducting material systems have been developed in the recent past, including calcium-intercalated graphite compounds, boron-doped diamond and-most prominently-iron arsenides such as LaO(1-x)F(x)FeAs (ref. 3). In the case of organic superconductors, however, no new material system with a high superconducting transition temperature (T(c)) has been discovered in the past decade. Here we report that intercalating an alkali metal into picene, a wide-bandgap semiconducting solid hydrocarbon, produces metallic behaviour and superconductivity. Solid potassium-intercalated picene (K(x)picene) shows T(c) values of 7 K and 18 K, depending on the metal content. The drop of magnetization in K(x)picene solids at the transition temperature is sharp (<2 K), similar to the behaviour of Ca-intercalated graphite. The T(c) of 18 K is comparable to that of K-intercalated C(60) (ref. 4). This discovery of superconductivity in K(x)picene shows that organic hydrocarbons are promising candidates for improved T(c) values.

  13. Superconductivity in alkali-doped fullerene nanowhiskers

    Science.gov (United States)

    Takeya, Hiroyuki; Konno, Toshio; Hirata, Chika; Wakahara, Takatsugu; Miyazawa, Kun'ichi; Yamaguchi, Takahide; Tanaka, Masashi; Takano, Yoshihiko

    2016-09-01

    Superconductivity in alkali metal-doped fullerene nanowhiskers (C60NWs) was observed in K3.3C60NWs, Rb3.0C60NWs and Cs2.0Rb1.0C60NWs with transition temperatures at 17, 25 and 26 K, respectively. Almost full shielding volume fraction (~80%) was observed in K3.3C60NWs when subjected to thermal treatment at 200 °C for a duration of 24 h. In contrast, the shielding fraction of Rb3.0C60NWs and Cs2.0Rb1.0C60NWs were calculated to be 8% and 6%, respectively. Here we report on an extensive investigation of the superconducting properties of these AC60NWs (A  =  K3.3, Rb3.0 and Cs2.0Rb1.0). These properties are compared to the ones reported on the corresponding conventional (single-crystal or powder) K-doped fullerene. We also evaluated the critical current densities of these C60NWs using the Bean model under an applied magnetic field up to 50 kOe.

  14. Alternative alkali resistant deNOx catalysts

    DEFF Research Database (Denmark)

    Putluru, Siva Sankar Reddy; Kristensen, Steffen Buus; Due-Hansen, Johannes;

    2012-01-01

    Alternative alkali resistant deNOx catalysts were prepared using three different supports ZrO2, TiO2 and Mordenite zeolite. The majority of the catalysts were prepared by incipient wetness impregnation of a commercial support, with vanadium, copper or iron precursor, one catalyst was prepared...... by onepot sol–gel method. All catalysts were characterized by BET, XRPD and NH3-TPD. Initial SCR activities of 8 out of 9 catalysts showed higher NO conversion at least at one temperature in the temperature range 300–500 ◦C compared to the conventional V2O5-WO3/TiO2 catalyst. After potassium poisoning (100......–130 µmol of K/g of catalyst) the relative drop in SCR activity and acidity was lower for all the alternative catalysts compared to the industrial V2O5-WO3/TiO2 catalyst. Furthermore, Cu/MOR and Nano-V2O5/Sul-TiO2 catalysts showed 8–16 times higher SCR activities than the conventional even after high...

  15. Alkali-aggregate reactivity of typical siliceious glass and carbonate rocks in alkali-activated fly ash based geopolymers

    Science.gov (United States)

    Lu, Duyou; Liu, Yongdao; Zheng, Yanzeng; Xu, Zhongzi; Shen, Xiaodong

    2013-08-01

    For exploring the behaviour of alkali-aggregate reactivity (AAR) in alkali-activated geopolymeric materials and assessing the procedures for testing AAR in geopolymers, the expansion behaviour of fly ash based geopolymer mortars with pure silica glass and typical carbonate rocks were studied respectively by curing at various conditions, i.e. 23°C and 38°C with relative humidity over 95%, immersed in 1M NaOH solution at 80°C. Results show that, at various curing conditions, neither harmful ASR nor harmful ACR was observed in geopolymers with the criteria specified for OPC system. However, with the change of curing conditions, the geopolymer binder and reactive aggregates may experience different reaction processes leading to quite different dimensional changes, especially with additional alkalis and elevated temperatures. It suggests that high temperature with additional alkali for accelerating AAR in traditional OPC system may not appropriate for assessing the alkali-aggregate reactivity behaviour in geopolymers designed for normal conditions. On the other hand, it is hopeful to control the dimensional change of geopolymer mortar or concrete by selecting the type of aggregates and the appropriate curing conditions, thus changing the harmful AAR in OPC into beneficial AAR in geopolymers and other alkali-activated cementitious systems.

  16. Colourants and related phases in leucogranite exploited as feldspar raw material: from waste to by-product enriched in critical metals

    Science.gov (United States)

    Vrbický, Tomáš; Prikryl, Richard; Jedlička, Pavel

    2017-04-01

    Feldspar-rich leucogranite formed by metasomatic / hydrothermal alteration of granitic precursors in theHorní Slavkov - Krásno ore district (making part of Slavkov crystalline unit located in the western part of the Bohemian Massif, Czech Republic) presents the largest exploited deposit for industrial feldspars in the Czech Republic. As for other feldspar resources, the quality of raw material is controlled by content of colourants, specifically due to presence of hydrated iron oxides (FOH) and Ti-oxides. The recent study originally focused on the re-examination of mineralogical control of concentration of these impurities. However, the SEM-EDS study revealed high content of additional phases such as Li-micas and/or Nb-Ta minerals, partly linked to the presence of FOH and Ti-oxides. Based on these results, laboratory experiments on potential beneficiation of the feldspar ore and on separation of various by-products were conducted by using combined gravitational and magnetic separation. These laboratory trials proved highly effective process allowing acquisition of Li-micas and Nb-Ta concentrate as by products. If the similar separation unit will be built in the industrial scale (only magnetic separation unit is working in the quarry at present), several tons of these highly valuable commodities can be obtained each year.

  17. Re ‘Luminescence dating of K-feldspar from sediments: a protocol without anomalous fading correction’ by Bo Li and Sheng-Hua Li

    DEFF Research Database (Denmark)

    Thomsen, Kristina Jørkov; Murray, Andrew; Jain, Mayank;

    2012-01-01

    Have recently proposed a new measurement procedure (MET-pIRIR) for luminescence dating using feldspar; they argue that this procedure reduces anomalous fading to negligible levels, and that it is a significant improvement over existing protocols (pIRIR290). Here we compare the measured equivalent...

  18. Alkali based slagging: a case study from Leigh Creek

    Energy Technology Data Exchange (ETDEWEB)

    R.A. Creelman; J. Bamberry; L.A. Juniper; C. Ward [University of Western Sydney, Penrith South, NSW (Australia)

    2003-07-01

    A systematic study was undertaken at NRG Port Augusta Power station in South Australia to determine the cause of ash deposition (slagging) in the boilers. Conventional wisdom suggests that iron in the ash is generally a major player in furnace ash deposition; however, mineralogical and chemical analyses of the deposits showed that the binding phase was plagioclase feldspar, dominated by the sodic feldspar albite. The study resulted in recognition that the cause of the formation of ash deposits in the North Flinders furnaces was the result of the ingestion of sodium and calcium into the melt that bound the deposits. This finding was a breakthrough in understanding the deposition process within these furnaces, and emphasises that not all slagging is iron related and that systematic studies of deposits, coal and ash make fundamental contributions to understanding the ash deposition mechanisms. 9 refs., 5 figs., 2 tabs.

  19. Interactions and low energy collisions between an alkali ion and an alkali atom of different nucleus

    CERN Document Server

    Rakshit, Arpita; Berriche, Hamid; Deb, Bimalendu

    2015-01-01

    We study theoretically interaction potentials and low energy collisions between different alkali atoms and alkali ions. Specifically, we consider systems like X + Y$^{+}$, where X(Y$^{+})$ is either Li(Cs$^+$) or Cs((Li$^+$), Na(Cs$^+$) or Cs(Na$^+$) and Li(Rb$^+$) or Rb(Li$^+$). We calculate the molecular potentials of the ground and first two excited states of these three systems using pseudopotential method and compare our results with those obtained by others. We calculate ground-state scattering wave functions and cross sections of these systems for a wide range of energies. We find that, in order to get convergent results for the total scattering cross sections for energies of the order $1$ K, one needs to take into account at least 60 partial waves. In the low energy limit ($< 1 \\mu$K), elastic scattering cross sections exhibit Wigner law threshold behavior while in the high energy limit the cross sections go as $E^{-1/3}$. We discuss qualitatively the possibilities of forming cold molecular ion by ...

  20. Hydrogen storage over alkali metal hydride and alkali metal hydroxide composites

    Institute of Scientific and Technical Information of China (English)

    Pei Yu; Yong Shen Chua; Hujun Cao; Zhitao Xiong; Guotao Wu; Ping Chen

    2014-01-01

    Alkali metal hydroxide and hydride composite systems contain both protic (H bonded with O) and hydridic hydrogen. The interaction of these two types of hydrides produces hydrogen. The enthalpy of dehydrogenation increased with the increase of atomic number of alkali metals, i.e.,-23 kJ/molH2 for LiOH-LiH, 55.34 kJ/molH2 for NaOH-NaH and 222 kJ/molH2 for KOH-KH. These thermodynamic calculation results were consistent with our experimental results. H2 was released from LiOH-LiH system during ball milling. The dehydrogenation temperature of NaOH-NaH system was about 150◦C; whereas KOH and KH did not interact with each other during the heating process. Instead, KH decomposed by itself. In these three systems, NaOH-NaH was the only reversible hydrogen storage system, the enthalpy of dehydrogenation was about 55.65 kJ/molH2 , and the corresponding entropy was ca. 101.23 J/(molH2 ·K), so the temperature for releasing 1.0 bar H2 was as high as 518◦C, showing unfavorable thermodynamic properties. The activation energy for hydrogen desorption of NaOH-NaH was found to be 57.87 kJ/mol, showing good kinetic properties.

  1. On-line alkali detector based on surface ionization

    Energy Technology Data Exchange (ETDEWEB)

    Olsson, J.G.; Loenn, B.; Jaeglid, B.; Engvall, K.; Pettersson, J.B.C. [Chalmers University of Technology, Goeteborg (Sweden). Dept. of Physical Chemistry GU

    1998-12-31

    This project adapts a new on-line alkali measurement technique to coal and biomass combustion and gasification. Alkali metal atoms are known to easily ionize in contact with hot metal surfaces, and the instrument is based on this principle called surface ionization (SI). The primary parts of the detector are a platinum filament and an ion collector. The platinum filament is supported between two electrodes and heated to the temperature for alkali vaporization in ionic form. The ion collector is situated close to the filament. The measured current is proportional to the arrival rate of alkali atoms onto the filament. Laboratory tests were performed on detector sensitivity, detection limit, and time response. Similar sensitivity to both sodium and potassium regardless of molecular form was found. The time response of the detector is determined to be approximately 1 ms enabling it to monitor fast concentration changes in flue gas. Particles with a size below 5 nm melt completely on the hot platinum surface and give similar signals. For larger particles, the ionization efficiency is not 100% and depends on the type of salt. This problem can be overcome with an alternative filament configuration. The detector function was tested in a laboratory high pressure furnace using different fuel samples, atmospheres, and pressures. Alkali release from coal in general is lower than for biomass samples, rate constants and activation energies for alkali release were determined. Measurements were carried out in a biomass pyrolysis apparatus and a gasification pilot plant. The detector function was not influenced by a high concentration of hydrocarbons in the gas phase, and the measurements confirmed detector function in a hostile environment. The detector performed well in laboratory tests, and is a strong candidate for further development into a standard on-line monitor of alkali species in hot flue gas. 10 refs., 16 figs.

  2. Molecular photons interfaced with alkali atoms.

    Science.gov (United States)

    Siyushev, Petr; Stein, Guilherme; Wrachtrup, Jörg; Gerhardt, Ilja

    2014-05-01

    Future quantum communication will rely on the integration of single-photon sources, quantum memories and systems with strong single-photon nonlinearities. Two key parameters are crucial for the single-photon source: a high photon flux with a very small bandwidth, and a spectral match to other components of the system. Atoms or ions may act as single-photon sources--owing to their narrowband emission and their intrinsic spectral match to other atomic systems--and can serve as quantum nonlinear elements. Unfortunately, their emission rates are still limited, even for highly efficient cavity designs. Single solid-state emitters such as single organic dye molecules are significantly brighter and allow for narrowband photons; they have shown potential in a variety of quantum optical experiments but have yet to be interfaced with other components such as stationary memory qubits. Here we describe the optical interaction between Fourier-limited photons from a single organic molecule and atomic alkali vapours, which can constitute an efficient quantum memory. Single-photon emission rates reach up to several hundred thousand counts per second and show a high spectral brightness of 30,000 detectable photons per second per megahertz of bandwidth. The molecular emission is robust and we demonstrate perfect tuning to the spectral transitions of the sodium D line and efficient filtering, even for emitters at ambient conditions. In addition, we achieve storage of molecular photons originating from a single dibenzanthanthrene molecule in atomic sodium vapour. Given the large set of molecular emission lines matching to atomic transitions, our results enable the combination of almost ideal single-photon sources with various atomic vapours, such that experiments with giant single-photon nonlinearities, mediated, for example, by Rydberg atoms, become feasible.

  3. Nature of the Charge Localized Between Alkali Adatoms and Metal Substrates

    OpenAIRE

    Wertheim, G. K.; Riffe, D. Mark; Citrin, P. H.

    1994-01-01

    Two previously unappreciated features in photoemission spectra from alkali atoms adsorbed on W(110), namely, the sign of the alkali-induced surface-atom core-level shift of the substrate at low coverage and the very large alkali shallow core-hole lifetime width at all coverages, show that the alkali-substrate interaction is not well described by a transfer of alkali charge. Instead, both features point to the formation of a charge cloud between the alkali adatom and substrate that is d...

  4. Multi-photon processes in alkali metal vapors

    Science.gov (United States)

    Gai, Baodong; Hu, Shu; Li, Hui; Shi, Zhe; Cai, Xianglong; Guo, Jingwei; Tan, Yannan; Liu, Wanfa; Jin, Yuqi; Sang, Fengting

    2015-02-01

    Achieving population inversion through multi-photon cascade pumping is almost always difficult, and most laser medium work under 1-photon excitation mechanism. But for alkali atoms such as cesium, relatively large absorption cross sections of several low, cascading energy levels enable them properties such as up conversion. Here we carried out research on two-photon excitation alkali fluorescence. Two photons of near infrared region are used to excite alkali atoms to n 2 D5/2, n 2 D3/2 or higher energy levels, then the blue fluorescence of (n+1) 2 P3/2,(n+1) 2 P1/2-->n 2 S1/2 are observed. Different pumping paths are tried and by the recorded spectra, transition routes of cesium are deducted and concluded. Finally the possibility of two-photon style DPALs (diode pumped alkali laser) are discussed, such alkali lasers can give output wavelengths in the shorter end of visual spectroscopy (400-460 nm) and are expected to get application in underwater communication and material laser processing.

  5. Thermally assisted desorption processes in electron bombarded alkali halides

    Energy Technology Data Exchange (ETDEWEB)

    Kolodziej, J.; Czuba, P.; Piatkowski, P.; Postawa, Z.; Kempter, V.; Szymonski, M. (Uniwersytet Jagiellonski, Cracow (Poland). Inst. Fizyki)

    The desorption of alkali and halogen atoms induced by the interaction of energetic electrons with surfaces of alkali halide crystals has been studied by means of an angular-resolved and mass-selected time-of-flight spectroscopy. It has been found that a considerable fraction of halogen atoms was ejected with hyperthermal energies of the order of 0.1 eV. However, alkali atoms and the remaining part of halogen emission had thermal (Maxwellian) spectra of kinetic energies. In this paper we will report on systematic investigations of these thermal desorption processes for single crystal (100) NaCl, KCl, KBr, RbBr, and Kl surfaces. The relative yield of the thermal component has been measured as a function of electron beam energy and beam current density at various sample temperatures. It will be shown that thermal halogen emission can be explained by thermally assisted diffusion of interstitial halogen atoms produced in the bulk of the crystal from decaying self-trapped excitons. The origin of the alkali atom component will be described as due to neutralization and subsequent thermal evaporation of excess alkali atoms from the halogen deficient surface. (Author).

  6. Utilization of Mineral Wools as Alkali-Activated Material Precursor

    Directory of Open Access Journals (Sweden)

    Juho Yliniemi

    2016-04-01

    Full Text Available Mineral wools are the most common insulation materials in buildings worldwide. However, mineral wool waste is often considered unrecyclable because of its fibrous nature and low density. In this paper, rock wool (RW and glass wool (GW were studied as alkali-activated material precursors without any additional co-binders. Both mineral wools were pulverized by a vibratory disc mill in order to remove the fibrous nature of the material. The pulverized mineral wools were then alkali-activated with a sodium aluminate solution. Compressive strengths of up to 30.0 MPa and 48.7 MPa were measured for RW and GW, respectively, with high flexural strengths measured for both (20.1 MPa for RW and 13.2 MPa for GW. The resulting alkali-activated matrix was a composite-type in which partly-dissolved fibers were dispersed. In addition to the amorphous material, sodium aluminate silicate hydroxide hydrate and magnesium aluminum hydroxide carbonate phases were identified in the alkali-activated RW samples. The only crystalline phase in the GW samples was sodium aluminum silicate. The results of this study show that mineral wool is a very promising raw material for alkali activation.

  7. Hg soil pollution around the Flix chlor-alkali plant

    Science.gov (United States)

    Esbrí, José Maria; López-Berdoces, Miguel Angel; Martínez-Coronado, Alba; Fernández-Calderon, Sergio; Díez, Sergi; León Higueras, Pablo

    2014-05-01

    Main mercury consumer in industrialized countries is the chlor-alkali industry. In Spain, this industry declares 2.54 tons of mercury emissions to the atmosphere per year, but the losses of mercury in this industrial process seem to be higher than this. In the next 15 years, these industries are going to make a technology change to a free mercury based technology. This study has been applied to the Flix (Tarragona, NE Spain) plant, located very near the Ebro River. Local industrial activity started in the late 18th Century, being the first Spanish industrial precinct in activity. Technology used in this plant is obsolete, and produces important emissions to the atmosphere. Besides, it has also produced an important pollution problem in the Ebro River. The aim of this work is the characterization of mercury soil pollution around the oldest chlor-alkali plant (CAP), actually in process of decommissioning. For this porpoises, we provided data of mercury in soils and in olive oil leaves, in order to assess the extent of this pollution, and the consequences in terms of transferring to local agricultural biota. We present data from two soils geochemistry surveys, one centered in the general area, and a second one centered in an anomalous area identified by the first survey, at the Ebro margins downstream the town area. A total of 126 surface soil samples were taken and analyzed for total mercury by means of a Lumex RA-915+ device with RP- 91C pyrolysis attachment. Soil-plant transfer was studied based on mercury contents in olive leaves, the most ubiquitous plant species in the area; these biological samples were thoroughly clean and freeze-dried before its total mercury analysis in a Lumex RA-915+ device with its RP-91c pyrolysis attachment. Mercury contents in soils reach maximum levels in the vicinity of CAP (495 mg kg-1), much higher than baseline levels found in the area (0.18 mg kg-1, in average). These polluted soils are located near CAP and the riverbanks of Ebro

  8. Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

    Science.gov (United States)

    Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

    2017-04-01

    Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this

  9. Maternal exposure to alkali, alkali earth, transition and other metals: Concentrations and predictors of exposure.

    Science.gov (United States)

    Hinwood, A L; Stasinska, A; Callan, A C; Heyworth, J; Ramalingam, M; Boyce, M; McCafferty, P; Odland, J Ø

    2015-09-01

    Most studies of metals exposure focus on the heavy metals. There are many other metals (the transition, alkali and alkaline earth metals in particular) in common use in electronics, defense industries, emitted via combustion and which are naturally present in the environment, that have received limited attention in terms of human exposure. We analysed samples of whole blood (172), urine (173) and drinking water (172) for antimony, beryllium, bismuth, cesium, gallium, rubidium, silver, strontium, thallium, thorium and vanadium using ICPMS. In general most metals concentrations were low and below the analytical limit of detection with some high concentrations observed. Few factors examined in regression models were shown to influence biological metals concentrations and explained little of the variation. Further study is required to establish the source of metals exposures at the high end of the ranges of concentrations measured and the potential for any adverse health impacts in children.

  10. Low-frequency Raman scattering in alkali tellurite glasses

    Indian Academy of Sciences (India)

    Angelos G Kalampounias

    2008-10-01

    Raman scattering has been employed to study the alkali-cation size dependence and the polarization characteristics of the low-frequency modes for the glass-forming tellurite mixtures, 0.1M2O–0.9TeO2 (M = Na, K, Rb and Cs). The analysis has shown that the Raman coupling coefficient alters by varying the type of the alkali cation. The addition of alkali modifier in the tellurite network leads to the conversion of the TeO4 units to TeO3 units with a varying number of non-bridging oxygen atoms. Emphasis has also been given to the lowfrequency modes and particular points related to the low-frequency Raman phenomenology are discussed in view of the experimental findings.

  11. Formation and Stability of High-Spin Alkali Clusters

    Science.gov (United States)

    Schulz, C. P.; Claas, P.; Schumacher, D.; Stienkemeier, F.

    2004-01-01

    Helium nanodroplet isolation has been applied to agglomerate alkali clusters at temperatures of 380mK. The very weak binding to the surface of the droplets allows a selection of only weakly bound, high-spin states. Here we show that larger clusters of alkali atoms in high-spin states can be formed. The lack of strong bonds from pairing electrons makes these systems nonmetallic, vanderWaals like complexes of metal atoms. We find that sodium and potassium readily form such clusters containing up to 25atoms. In contrast, this process is suppressed for rubidium and cesium. Apparently, for these heavy alkalis, larger high-spin aggregates are not stable and depolarize spontaneously upon cluster formation.

  12. Oscillation Frequencies for Simultaneous Trapping of Heteronuclear Alkali Atoms

    CERN Document Server

    Kaur, Kiranpreet; Arora, Bindiya

    2016-01-01

    We investigate oscillation frequencies for simultaneous trapping of more than one type of alkali atoms in a common optical lattice. For this purpose, we present numerical results for magic trapping conditions, where the oscillation frequencies for two different kind of alkali atoms using laser lights in the wavelength range 500-1200 nm are same. These wavelengths will be of immense interest for studying static and dynamic properties of boson-boson, boson-fermion, fermion-fermion, and boson-boson-boson mixtures involving different isotopes of Li, Na, K, Rb, Cs and Fr alkali atoms. In addition to this, we were also able to locate a magic wavelength around 808.1 nm where all the three Li, K, and Rb atoms are found to be suitable for oscillating at the same frequency in a common optical trap.

  13. Characterization of alkali-modified soy protein concentrate

    Directory of Open Access Journals (Sweden)

    Barać Miroljub B.

    2005-01-01

    Full Text Available To study the influence of the preparation mode, including mild alkali modification, of soy protein concentrate on soluble protein content and composition, some of its nutritive and functional properties were investigated. Soy protein concentrate prepared by aqueous alcohol leaching was modified in mild alkaline solutions (pH 8.0 at 40, 50 and 60° C for 60 minutes and compared with two principal types of commercial soy protein concentrate. Soluble protein content, composition and properties of soy protein concentrate, as well as their potential use are essentially determined by the preparation mode. Limited mild alkali hydrolysis increased protein solubility by 40-71%, while emulsion stability was increased by 18-56%. Major storage soybean proteins exhibited different stability to alcohol denaturation and mild alkali modification. The most susceptible were acidic -A3 - and -A5- subunits of glycinin.

  14. Properties of Hooked Steel Fibers Reinforced Alkali Activated Material Concrete

    Directory of Open Access Journals (Sweden)

    Faris M. A.

    2016-01-01

    Full Text Available In this study, alkali activated material was produced by using Class F fly ash from Manjung power station, Lumut, Perak, Malaysia. Fly ash then was activated by alkaline activator which is consisting of sodium silicate (Na2SiO3 and sodium hydroxide (NaOH. Hooked end steel fibers were added into the alkali activated material system with percentage vary from 0 % – 5 %. Chemical compositions of fly ash were first analyzed by using x-ray fluorescence (XRF. All hardened alkali activated material samples were tested for density, workability, and compression after 28 days. Results show a slight increase of density with the addition of steel fibers. However, the workability was reduced with the addition of steel fibers content. Meanwhile, the addition of steel fibers shows the improvement of compressive strength which is about 19 % obtained at 3 % of steel fibers addition.

  15. Temperature dependent dynamic ESD processes in alkali halides

    Energy Technology Data Exchange (ETDEWEB)

    Kolodziej, J.; Czuba, P.; Piatkowski, P.; Poradzisz, A.; Postawa, Z. (Inst. of Physics, Jagellonian Univ., Krakow (Poland)); Szymonski, M. (Inst. for Materials Research, McMaster Univ., Hamilton, Ontario (Canada)); Fine, J. (Surface and Microanalysis Div., National Inst. of Standards and Tech., Gaithersburg, MD (United States))

    1992-03-01

    The effect of the sample temperature on angular-resolved kinetic-energy distributions of alkali and halogen atoms, electronically desorbed from single crystal alkali halides, has been measured. It was found that while the emission of particles with thermal energies increased by about a factor of 40 in the temperature range 90-300degC, the nonthermal halogen atom intensity decreased by about a factor of 3. From these temperature dependent measurements the activation energies for thermally assisted defect migration processes have been estimated. The results will be compared with the data available in the literature and the predictions of a recently proposed model for electron-stimulated desorption (ESD) of alkali halides. (orig.).

  16. Neuropsychiatric manifestations of alkali metal deficiency and excess

    Energy Technology Data Exchange (ETDEWEB)

    Yung, C.Y.

    1984-01-01

    The alkali metals from the Group IA of the periodic table (lithium, sodium, potassium, rubidium, cesium and francium) are reviewed. The neuropsychiatric aspects of alkali metal deficiencies and excesses (intoxications) are described. Emphasis was placed on lithium due to its clinical uses. The signs and symptoms of these conditions are characterized by features of an organic brain syndrome with delirium and encephalopathy prevailing. There are no clinically distinctive features that could be reliably used for diagnoses. Sodium and potassium are two essential alkali metals in man. Lithium is used as therapeutic agent in bipolar affective disorders. Rubidium has been investigated for its antidepressant effect in a group of psychiatric disorders. Cesium is under laboratory investigation for its role in carcinogenesis and in depressive illness. Very little is known of francium due to its great instability for experimental study.

  17. Orbital Feshbach Resonance in Alkali-Earth Atoms.

    Science.gov (United States)

    Zhang, Ren; Cheng, Yanting; Zhai, Hui; Zhang, Peng

    2015-09-25

    For a mixture of alkali-earth atomic gas in the long-lived excited state ^{3}P_{0} and the ground state ^{1}S_{0}, in addition to nuclear spin, another "orbital" index is introduced to distinguish these two internal states. In this Letter we propose a mechanism to induce Feshbach resonance between two atoms with different orbital and nuclear spin quantum numbers. Two essential ingredients are the interorbital spin-exchange process and orbital dependence of the Landé g factors. Here the orbital degrees of freedom plays a similar role as the electron spin degree of freedom in magnetic Feshbach resonance in alkali-metal atoms. This resonance is particularly accessible for the ^{173}Yb system. The BCS-BEC crossover in this system requires two fermion pairing order parameters, and displays a significant difference compared to that in an alkali-metal system.

  18. A low-power reversible alkali atom source

    Science.gov (United States)

    Kang, Songbai; Mott, Russell P.; Gilmore, Kevin A.; Sorenson, Logan D.; Rakher, Matthew T.; Donley, Elizabeth A.; Kitching, John; Roper, Christopher S.

    2017-06-01

    An electrically controllable, solid-state, reversible device for sourcing and sinking alkali vapor is presented. When placed inside an alkali vapor cell, both an increase and decrease in the rubidium vapor density by a factor of two are demonstrated through laser absorption spectroscopy on 10-15 s time scales. The device requires low voltage (5 V), low power (power), and low energy (<10.7 mJ per 10 s pulse). The absence of oxygen emission during operation is shown through residual gas analysis, indicating that Rb is not lost through chemical reaction but rather by ion transport through the designed channel. This device is of interest for atomic physics experiments and, in particular, for portable cold-atom systems where dynamic control of alkali vapor density can enable advances in science and technology.

  19. The Distribution of Sand with Alkali Activity from Danjiang River in Shangluo and Its Safe Handling%商洛丹江河砂碱活性区域分布与安全使用措施

    Institute of Scientific and Technical Information of China (English)

    王绪旺; 周春生

    2016-01-01

    Aggregate alkali activity affects the durability and safety of the concrete constructions . Here , petrographic method and accelerated mortar bar method were adopted to identify and detect the alkali activity of the sand in Danjiang river ,Shangluo ,and then the distribution characteristics of sand with alkali activity was obtained based on the experi-mental research ,which could provide some guidance for the sand safety of concrete constructions .Petrographic analysis results indicate that the mineral composition of Danjiang River sand is basically the same , it' s mainly composed of quartz ,feldspar ,calcite ,mica and mixed sand ,with very little alkali active mineral composition .The accelerated mortar bar test results indicate that:the Danjiang River sand has no alkali activity ,but there are potential active components of aggregate .After adding 15% fly ash (weight ) ,the expansion rate of the sample block is reduced ,which indicates that the fly ash has a good inhibition effect on alkali activity of river sand ,and other measures should be taken to ensure the safety of concrete constructions .%骨料的碱活性影响着混凝土工程的安全耐久 ,采用岩相法和快速砂浆棒法对商洛市丹江河砂是否具有碱活性进行了鉴定检测和实验研究 ,并分析出丹江河砂碱活性的区域分布特征 ,为混凝土工程用砂安全提供参考.岩相分析结果表明 :丹江河砂的矿物组成成分基本相同 ,主要由石英、长石、方解石、云母和杂砂组成 ,具有碱活性矿物成分较少.快速砂浆棒法测试结果表明 :丹江河砂不具有碱活性 ,但是存在潜在的骨料活性成分.掺加15% 粉煤灰后 ,测定试件膨胀率降低 ,表明粉煤灰对河砂的碱活性起到了良好的抑制作用 ,使用时还应采取其它一定措施 ,以保证混凝土的使用安全.

  20. Hydrothermal chemistry, structures, and luminescence studies of alkali hafnium fluorides.

    Science.gov (United States)

    Underwood, Christopher C; McMillen, Colin D; Chen, Hongyu; Anker, Jeffery N; Kolis, Joseph W

    2013-01-07

    This paper describes the hydrothermal chemistry of alkali hafnium fluorides, including the synthesis and structural characterization of five new alkali hafnium fluorides. Two ternary alkali hafnium fluorides are described: Li(2)HfF(6) in space group P31m with a = 4.9748(7) Å and c = 4.6449(9) Å and Na(5)Hf(2)F(13) in space group C2/m with a = 11.627(2) Å, b = 5.5159(11) Å, and c = 8.4317(17) Å. Three new alkali hafnium oxyfluorides are also described: two fluoroelpasolites, K(3)HfOF(5) and (NH(4))(3)HfOF(5), in space group Fm3m with a = 8.9766(10) and 9.4144(11) Å, respectively, and K(2)Hf(3)OF(12) in space group R3m with a = 7.6486(11) Å and c = 28.802(6) Å. Infrared (IR) spectra were obtained for the title solids to confirm the structure solutions. Comparison of these materials was made based on their structures and synthesis conditions. The formation of these species in hydrothermal fluids appears to be dependent upon both the concentration of the alkali fluoride mineralizer solution and the reaction temperature. Both X-ray and visible fluorescence studies were conducted on compounds synthesized in this study and showed that fluorescence was affected by a variety of factors, such as alkali metal size, the presence/absence of oxygen in the compound, and the coordination environment of Hf(4+).

  1. A comparative study of K-rich and Na/Ca-rich feldspar ice-nucleating particles in a nanoliter droplet freezing assay

    Science.gov (United States)

    Peckhaus, Andreas; Kiselev, Alexei; Hiron, Thibault; Ebert, Martin; Leisner, Thomas

    2016-09-01

    A recently designed droplet freezing assay was used to study the freezing of up to 1500 identical 0.2 nL water droplets containing suspensions of one Na/Ca-rich feldspar and three K-rich and one Na/Ca-rich feldspar particles. Three types of experiments have been conducted: cooling ramp, isothermal freezing at a constant temperature, and freeze-thaw cycles. The observed freezing behavior has been interpreted with the help of a model based on the classical nucleation theory (soccer ball model (SBM); Niedermeier et al., 2015). By applying the model to the different freezing experiments conducted with the same ice-nucleating material, the unique sets of model parameters for specific feldspar suspensions could be derived. The SBM was shown to adequately describe the observed cooling rate dependence, the ice-nucleating active sites (INAS) surface density ns(T) in a wide temperature range, and the shift of the freezing curves towards lower temperature with dilution. Moreover, the SBM was capable of reproducing the variation of INAS surface density ns(T) with concentration of ice-nucleating particles in the suspension droplets and correctly predicting the leveling-off of ns(T) at low temperature. The freeze-thaw experiments have clearly shown that the heterogeneous freezing induced even by very active ice-nucleating species still possesses a stochastic nature, with the degree of randomness increasing towards homogeneous nucleation. A population of the high-temperature INAS has been identified in one of the K-rich feldspar samples. The freezing of 0.8 wt % suspension droplets of this particular feldspar was observed already at -5 °C. These high-temperature active sites could be deactivated by treating the sample with hydrogen peroxide but survived heating up to 90 °C. Given a high mass concentration of these high-temperature active sites (2.9 × 108 g-1) and a very low value of contact angle (0.56 rad) the possibility of biological contamination of the sample was

  2. Ocular alkali burn associated with automobile air-bag activation.

    Science.gov (United States)

    White, J E; McClafferty, K; Orton, R B; Tokarewicz, A C; Nowak, E S

    1995-01-01

    Alkali burns of the eye can result in permanent visual impairment and are therefore potentially devastating. Immedicate diagnosis and treatment are essential to a good prognosis. The authors report the case of a 52-year-old woman who suffered alkali keratitis as the result of the activation of an automobile air bag. This type of injury will be seen more frequently as more cars are equipped with air bags and should be suspected in drivers and passengers involved in accidents in which air bags have been activated. PMID:7553495

  3. Interaction of alkali-metal overlayers with oxygen

    Energy Technology Data Exchange (ETDEWEB)

    Hrbek, J.; Xu, G.; Sham, T.K.; Shek, M.L.

    1989-05-01

    The interaction of oxygen with alkali metals (Li, Na, K, and Cs) was studied with valence and core-level photoemission (PE) using synchrotron radiation and by multiple mass thermal desorption (TDS). During a stepwise coadsorption of oxygen at 80 K, an increase in the emission intensity, a linewidth broadening, and a negative binding-energy shift of alkali-metal core levels is observed. Two stages of oxygen adsorption are identified in PE and TDS. In the low O/sub 2/ exposure range, an oxide species is formed; at higher exposures, peroxide and superoxide species are observed in Na, K, and Cs. The potassium--oxygen interaction is discussed in detail.

  4. Upgrading of petroleum oil feedstocks using alkali metals and hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2014-09-09

    A method of upgrading an oil feedstock by removing heteroatoms and/or one or more heavy metals from the oil feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase separable from the organic oil feedstock material. The upgradant hydrocarbon bonds to the oil feedstock material and increases the number of carbon atoms in the product. This increase in the number of carbon atoms of the product increases the energy value of the resulting oil feedstock.

  5. Assessment of concrete bridge decks with alkali silica reactions

    DEFF Research Database (Denmark)

    Eriksen, Kirsten; Jansson, Jacob; Geiker, Mette Rica

    2008-01-01

    Based on investigations of concrete from an approximately 40 years old bridge a procedure to support the management of maintenance and repair of alkali silica damaged bridges is proposed. Combined petrography and accelerated expansion testing were undertaken on cores from the Bridge at Skovdiget......, Bagsværd, Denmark to provide information on the damage condition as well as the residual reactivity of the concrete. The Danish Road Directory’s guidelines for inspection and assessment of alkali silica damaged bridges will be briefly presented, and proposed modifications will be describe...

  6. A hidden history of heartburn: The milk-alkali syndrome.

    Science.gov (United States)

    Swaminathan, Krishnan

    2011-02-01

    Milk-alkali syndrome was once considered to be of historic interest and a rare cause of hypercalcemia. Currently, it should be an important consideration in the differential diagnosis of hypercalcemia, after malignancies and primary hyperparathyroidism. The resurgence is in part due to the easy availability of over the counter (OTC) calcium preparations. We describe a 50-year-old man who presented with severe hypercalcemia on two occasions associated with renal failure and metabolic alkalosis. Extensive investigations during the first admission failed to unravel a specific cause of hypercalcemia but a thorough history during his subsequent admission helped to confirm the diagnosis of milk-alkali syndrome.

  7. Upgrading of petroleum oil feedstocks using alkali metals and hydrocarbons

    Science.gov (United States)

    Gordon, John Howard

    2014-09-09

    A method of upgrading an oil feedstock by removing heteroatoms and/or one or more heavy metals from the oil feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase separable from the organic oil feedstock material. The upgradant hydrocarbon bonds to the oil feedstock material and increases the number of carbon atoms in the product. This increase in the number of carbon atoms of the product increases the energy value of the resulting oil feedstock.

  8. MINERALOGICAL FEATURES OF ULTRAMAFIC HYPOXENOLITHS IN ALKALI-RICH PORPHYRY

    Institute of Scientific and Technical Information of China (English)

    LIU Xianfan; YANG Zhengxi; LIU Jiaduo; ZHANG Chengjiang; WU Dechao; LI Youguo

    2003-01-01

    Ultramafic hypoxenoliths found in the alkali-rich porphyry in the Liuhe Village, Heqing, Yunnan,China, are of great significance in understanding the origin and evolution of the porphyry. This paper discusses the mineralogical features of the hypoxenoliths. It shows that the xenoliths are characterized by the upper mantle rocks modified to certain extent by the enriched mantle fluid metasomatism in the mantle environment, with the enriched mantle property of Iow-degree partial melting. This constitutes the important mineralogical evidence for the petrogenesis and mineralization of alkali-rich porphyry.

  9. Ethanol production via in situ fungal saccharification and fermentation of mild alkali and steam pretreated corn fiber.

    Science.gov (United States)

    Shrestha, Prachand; Khanal, Samir Kumar; Pometto, Anthony L; Hans van Leeuwen, J

    2010-11-01

    The effect of mild alkali and steam pretreatments on fungal saccharification and sequential simultaneous-saccharification and fermentation (SSF) of corn fiber to ethanol was studied. The corn fiber was pretreated with: (i) 2% NaOH (w/w) at 30 degrees C for 2h and (ii) steaming at 100 degrees C for 2h. Ethanol yields were 2.6g, 2.9g and 5.5g ethanol/100g of corn fiber, respectively, for Phanerochaete chrysosporium, Gloeophyllum trabeum and Trichoderma reesei saccharification and sequential SSFs. SSF with commercial cellulase enzyme - Spezyme-CP had 7.7g ethanol/100g corn fiber. Mild alkali pretreatment resulted in higher glucose yields following fungal saccharification of corn fiber. However, the ethanol yields were comparatively similar for untreated and mild alkali pretreated corn fiber. Solid-substrate fermentation of corn fiber with fungi can be improved to either eliminate or reduce the dosage of commercial cellulase enzymes during SSF.

  10. IRMPD action spectroscopy of alkali metal cation-cytosine complexes: effects of alkali metal cation size on gas phase conformation.

    Science.gov (United States)

    Yang, Bo; Wu, R R; Polfer, N C; Berden, G; Oomens, J; Rodgers, M T

    2013-10-01

    The gas-phase structures of alkali metal cation-cytosine complexes generated by electrospray ionization are probed via infrared multiple photon dissociation (IRMPD) action spectroscopy and theoretical calculations. IRMPD action spectra of five alkali metal cation-cytosine complexes exhibit both similar and distinctive spectral features over the range of ~1000-1900 cm(-1). The IRMPD spectra of the Li(+)(cytosine), Na(+)(cytosine), and K(+)(cytosine) complexes are relatively simple but exhibit changes in the shape and shifts in the positions of several bands that correlate with the size of the alkali metal cation. The IRMPD spectra of the Rb(+)(cytosine) and Cs(+)(cytosine) complexes are much richer as distinctive new IR bands are observed, and the positions of several bands continue to shift in relation to the size of the metal cation. The measured IRMPD spectra are compared to linear IR spectra of stable low-energy tautomeric conformations calculated at the B3LYP/def2-TZVPPD level of theory to identify the conformations accessed in the experiments. These comparisons suggest that the evolution in the features in the IRMPD action spectra with the size of the metal cation, and the appearance of new bands for the larger metal cations, are the result of the variations in the intensities at which these complexes can be generated and the strength of the alkali metal cation-cytosine binding interaction, not the presence of multiple tautomeric conformations. Only a single tautomeric conformation is accessed for all five alkali metal cation-cytosine complexes, where the alkali metal cation binds to the O2 and N3 atoms of the canonical amino-oxo tautomer of cytosine, M(+)(C1).

  11. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fluorinated carboxylic acid alkali... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  12. Formation of alkali-metal nanoparticles in alkali-silicate glasses under electron irradiation and thermal processing

    Science.gov (United States)

    Bochkareva, E. S.; Sidorov, A. I.; Ignat'ev, A. I.; Nikonorov, N. V.; Podsvirov, O. A.

    2017-02-01

    Experiments and numerical simulation show that the irradiation of alkali-containing glasses using electrons at an energy of 35 keV and the subsequent thermal processing at a temperature above the vitrification point lead to the formation of spherical metal (lithium, sodium, and potassium) nanoparticles with oxide sheaths that exhibit plasmon resonances in the visible spectral range. Glasses containing two alkali metals exhibit mutual effect of metals on the formation of nanoparticles with two compositions due to the difference of ion radii and mobilities of metal ions.

  13. A simple melting theory applied to alkali halide, alkaline-earth chalcogenide, and alkali chalco-genide compounds

    Science.gov (United States)

    Liu, Q.; Chen, L. R.

    2005-06-01

    A useful and simple method for studying the melting temperature T-m of ion compounds has been developed by using analyses originally due to diffusional force theory, incorporating Pandey's formulation and Harrison's potential function. The calculated values of T-m for a wide range of compounds of types IA-VII (alkali halide), IIA-VI (alkaline-earth chalcogenide), and IA-VI (alkali chalcogenide) are found to agree fairly well with experimental values for T-m and to be superior to results from previous approaches involving similar methods.

  14. Post-IR IRSL290 dating of K-rich feldspar sand grains in a wind-dominated system on Sardinia

    DEFF Research Database (Denmark)

    Andreucci, S.; Sechi, D.; Buylaert, Jan-Pieter

    2017-01-01

    block sand-sized grains for quartz SAR-OSL and K-feldspar pIRIR dating were collected. The natural quartz SAR-OSL sample lies below the saturation limit of the dose response curve (De ... with the quartz result. A further test on older samples was carried out on the sedimentary succession at Bue Marino cave, which includes a sandy wind-blown unit, enclosed between two calcareous crusts. U-series dates of crusts constrain the aeolianite formation between ∼130 and ∼86 ka. The quartz SAR-OSL signals....... The pIRIR290 ages indicate an offset up to ∼1000 years. We can conclude that the pIRIR290 method on sand-sized K-feldspar grains shows great promise for samples at or beyond the quartz OSL age limit but should not be applied to Late Holocene or modern deposits....

  15. A comparative study of the luminescence characteristics of polymineral fine grains and coarse-grained K-, and Na-rich feldspars

    DEFF Research Database (Denmark)

    Tsukamoto, Sumiko; Jain, Mayank; Murray, Andrew S.;

    2012-01-01

    for K-feldspar samples, when a preheat temperature of 250 °C for 60 s is used. After preheating to a higher temperature (320 °C for 60 s) all samples show a TL reduction around 410 °C in the blue detection window. Pulse annealing experiments for IRSL and pIRIR signals for preheats between 320 °C and 500...

  16. Energy conservation in the primary aluminum and chlor-alkali industries

    Energy Technology Data Exchange (ETDEWEB)

    1980-10-01

    The primary aluminum and chlor-alkali industries together use nearly 13% of the electrical energy consumed by US industry. As part of its mission to promote energy conservation in basic US industries, the DOE surveys the present technological status of the major electrochemical industries and evaluates promising technological innovations that may lead to reduced energy requirements. This study provides technical and economic analyses in support of a government program of research and development in advanced electrolytic technology. This program is intended to supplement the development efforts directed toward energy savings by private industry. Sections II and III of this report cover aluminum and chlorine production processes only, since these two industries represent over 90% of the electrical energy requirements of all electrolytic industries in the United States. Section IV examines barriers to accelerated research and development by the electrolytic industries, and makes suggestions for government actions to overcome these barriers.

  17. Influence of temperature on alkali stress adaptation in Listeria monocytogenes

    Science.gov (United States)

    Listeria monocytogenes cells may induce alkali stress adaptation when exposed to sublethal concentrations of alkaline cleaners and sanitizers that may be frequently used in the food processing environment. In the present study, the effect of temperature on the induction and the stability of such alk...

  18. Chlor-Alkali Industry: A Laboratory Scale Approach

    Science.gov (United States)

    Sanchez-Sanchez, C. M.; Exposito, E.; Frias-Ferrer, A.; Gonzalez-Garaia, J.; Monthiel, V.; Aldaz, A.

    2004-01-01

    A laboratory experiment for students in the last year of degree program in chemical engineering, chemistry, or industrial chemistry is presented. It models the chlor-alkali process, one of the most important industrial applications of electrochemical technology and the second largest industrial consumer of electricity after aluminium industry.

  19. Alkali and Halogen Chemistry in Volcanic Gases on Io

    CERN Document Server

    Schaefer, L

    2004-01-01

    We use chemical equilibrium calculations to model the speciation of alkalis and halogens in volcanic gases emitted on Io. The calculations cover wide temperature (500-2000 K) and pressure (10^-6 to 10^+1 bars) ranges, which overlap the nominal conditions at Pele (T = 1760 K, P = 0.01 bars). About 230 compounds of 11 elements (O, S, Li, Na, K, Rb, Cs, F, Cl, Br, I) are considered. We predict the major alkali and halogen species in a Pele-like volcanic gas and the major alklai and halogen condensates. We also model disequilibrium chemistry of the alkalis and halogens in the volcanic plume. Based on this work and our prior modeling for Na, K, and Cl in a volcanic plume, we predict the major loss processes for the alkali halide gases are photolysis and/or condensation onto grains. On the basis of elemental abundances and photochemical lifetimes, we recommend searching for gaseous KCl, NaF, LiF, LiCl, RbF, RbCl, CsF, and CsCl around volcanic vents during eruptions. Based on abundance considerations and observation...

  20. Effect of Pozzolanic Reaction Products on Alkali-silica Reaction

    Institute of Scientific and Technical Information of China (English)

    WEI Fengyan; LAN Xianghui; LV Yinong; XU Zhongzi

    2006-01-01

    The effect of fly ash on controlling alkali-silica reaction (ASR) in simulated alkali solution was studied. The expansion of mortar bars and the content of Ca(OH)2 in cement paste cured at 80 ℃ for 91 d were measured. Transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM) were employed to study the microstructure of C-S-H. TEM/energy dispersive spectroscopy (EDS) was then used to determine the composition of C-S-H. The pore structure of the paste was analyzed by mercury intrusion porosimetry (MIP). The results show that the contents of fly ash of 30% and 45% can well inhibit ASR. And the content of Ca(OH)2 decreases with the increase of fly ash. That fly ash reacted with Ca(OH)2 to produce C-S-H with a low Ca/Si molar ratio could bind more Na+ and K+ ions, and produce a reduction in the amount of soluble alkali available for ASR. At the same time, the C-S-H produced by pozzolanic reaction converted large pores to smaller ones (gel pores smaller than 10 nm) to densify the pore structure. Perhaps that could inhibit alkali transport to aggregate for ASR.

  1. Influence of temperature on alkali stress adaptation in Listeria monocytogenes

    Science.gov (United States)

    Listeria monocytogenes cells may induce alkali stress adaptation when exposed to sublethal concentrations of alkaline cleaners and sanitizers that may be frequently used in the food processing environment. In the present study, the effect of temperature on the induction and the stability of such alk...

  2. Ion conducting fluoropolymer carbonates for alkali metal ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    DeSimone, Joseph M.; Pandya, Ashish; Wong, Dominica; Balsara, Nitash P.; Thelen, Jacob; Devaux, Didier

    2017-09-05

    Liquid or solid electrolyte compositions are described that comprise a homogeneous solvent system and an alkali metal salt dissolved in said solvent system. The solvent system may comprise a fluoropolymer, having one or two terminal carbonate groups covalently coupled thereto. Batteries containing such electrolyte compositions are also described.

  3. Powder X-ray diffraction study af alkali alanates

    DEFF Research Database (Denmark)

    Cao, Thao; Mosegaard Arnbjerg, Lene; Jensen, Torben René

    Powder X-ray diffraction study of alkali alanates Thao Cao, Lene Arnbjerg, Torben R. Jensen. Center for Materials Crystallography (CMC), Center for Energy Materials (CEM), iNANO and Department of Chemistry, Aarhus University, DK-8000, Denmark. Abstract: To meet the energy demand in the future...

  4. A new mechanism for radiation damage processes in alkali halides

    NARCIS (Netherlands)

    Dubinko, V.I.; Turkin, A.A.; Vainshtein, D.I.; Hartog, H.W. den

    1999-01-01

    We present a theory of radiation damage formation in alkali halides based on a new mechanism of dislocation climb, which involves the production of VF centers (self-trapped hole neighboring a cation vacancy) as a result of the absorption of H centers of dislocation lines. We consider the evolution o

  5. Powder X-ray diffraction study af alkali alanates

    DEFF Research Database (Denmark)

    Cao, Thao; Mosegaard Arnbjerg, Lene; Jensen, Torben René

    for mobile applications, new materials with high gravimetric and volumetric storage capacity of hydrogen have to be developed. Alkali alanates are promising for hydrogen storage materials. Sodium alanate stores hydrogen reversibly at moderate conditions when catalysed with, e.g. titanium, whereas potassium...

  6. Assesment of Alkali Resistance of Basalt Used as Concrete Aggregates

    Directory of Open Access Journals (Sweden)

    al-Swaidani Aref M.

    2015-11-01

    Full Text Available The objective of this paper is to report a part of an ongoing research on the influence of using crushed basalt as aggregates on one of durability-related properties of concrete (i.e. alkali-silica reaction which is the most common form of Alkali-Aggregate Reaction. Alkali resistance has been assessed through several methods specified in the American Standards. Results of petrographic examination, chemical test (ASTM C289 and accelerated mortar bar test (ASTM C1260 have particularly been reported. In addition, the weight change and compressive strength of 28 days cured concrete containing basaltic aggregates were also reported after 90 days of exposure to 10% NaOH solution. Dolomite aggregate were used in the latter test for comparison. The experimental results revealed that basaltic rocks quarried from As-Swaida’a region were suitable for production of aggregates for concrete. According to the test results, the studied basalt aggregates can be classified as innocuous with regard to alkali-silica reaction. Further, the 10% sodium hydroxide attack did not affect the compressive strength of concrete.

  7. Cationic polyelectrolyte induced separation of some inorganic contaminants and their mixture (zirconium silicate, kaolin, K-feldspar, zinc oxide) as well as of the paraffin oil from water.

    Science.gov (United States)

    Ghimici, Luminita

    2016-03-15

    The flocculation efficiency of a cationic polyelectrolyte with quaternary ammonium salt groups in the backbone, namely PCA5 was evaluated on zirconium silicate (kreutzonit), kaolin, K- feldspar and zinc oxide (ZnO) suspensions prepared either with each pollutant or with their mixture. The effect of several parameters such as settling time, polymer dose and the pollutant type on the separation efficacy was evaluated and followed by optical density and zeta potential measurements. Except for ZnO, the interactions between PCA5 and suspended particles led to low residual turbidity values (around 4% for kreutzonit, 5% for kaolin and 8% for K-feldspar) as well as to the reduction of flocs settling time (from 1200 min to 30 min and 120 min in case of kaolinit and K-feldspar, respectively), that meant a high efficiency in their separation. The negative value of the zeta potential and flocs size measurements, at the optimum polymer dose, point to contribution from charge patch mechanism for the particles flocculation. A good efficiency of PCA5 in separation of paraffin oil (a minimum residual turbidity of 9.8%) has been also found. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Stoneware tile manufacturing using rice straw ash as feldspar replacement; Fabricacion de gres porcelanico empleando ceniza de tamo de arroz en sustitucion del feldespato

    Energy Technology Data Exchange (ETDEWEB)

    Alvaro Guzman, A.; John Torres, L.; Martha Cedeno, V.; Silvio Delvasto, A.; Vicente Amigo, B.; Enrique Sanchez, V.

    2013-07-01

    In this research are presented the results of using rice straw ash (RSA) in low proportions as substitute of feldspar for manufacturing stoneware tiles. Specimens of semidry triaxial mixtures, where feldspar was substituted for different percentages (25 % and 50 %) of RSA, were prepared by uniaxial pressing, followed by drying and sintering. Physical and mechanical properties of sintered bodies were evaluated. Porcelain stoneware tile specimens C0 and CF25 reached bending strength and water absorption values were in accordance with standard ISO 13006 (Annex G, BIa) ( {>=} 35 MPa and {<=} 0.5 %, respectively). However, in porcelain stoneware tile specimens CF50 due to bloating phenomenon was not possible obtain commercial tiles in accordance with standard ISO 13006. By using Scanning Electron Microscopy (SEM) needles of primary and secondary mullite were identified in a vitreous phase; and by using X-Ray Diffraction (XRD) mullite and quartz phases were identified. It was concluded that feldspar can be substituted positively by RSA in stoneware tile pastes. (Author)

  9. Heating Stage Experimental Study of Melt Inclusions in Feldspars from Three Holocene Eruptions of Changbaishan Tianchi Volcano

    Institute of Scientific and Technical Information of China (English)

    Li Ni; Nicole Métrich; Fan Qicheng

    2008-01-01

    There occurred several eruptions from Changbaishan Tianchi volcano in Holocene, and at least three of them were believed to be true according to the formal studies. The products of three eruptions were yellow comenditic pumice of - 5000a B.P. (Eruption Ⅰ), gray comenditic pumice and pyroclastic flow of - 1000a B.P. (Eruption Ⅱ, i.e. the millennium explosive eruption), black trachy pumice and welded tuff of-300a B.P. (Eruption Ⅲ) respectively. There were a large number of melt inclusions found in phenocrysts, which differ in size and color. The Leitz 1350 heating stage experiments for melt inclusions in host feldspars from three Holocene eruptions of Changbaishan Tianchi volcano imply that there were little differences between the homogenization temperatures of melt inclusions from Eruptions Ⅰ and Ⅲ, whereas it was rather complicated for Eruption Ⅱ, i.e. there might be two kinds of melt with different homogenization temperature periods, which gave the evidence for the assumption that the explosive millennium eruption of Tianchi volcano was triggered by injection and mixing of two different magmas. The experimental results also indicate that (1) small melt inclusion is easy to be homogenized, while the large one, especially the one with lots of daughter crystals, is rather difficult to be homogenized; (2) homogenization temperature closely correlates with the size of melt inclusion within host crystal, with the temperature point switching from high heating rate to low heating rate, and correlates with whether it is the first time to obtain homogenization as well; and (3) a melt inclusion can get different homogenization temperatures when it is repeatedly heated. Even more, the next homogenization temperature is usually higher than the former one, which testifies the phenomenon that hydrogen migration occurs during repeated heating.

  10. The effect of microbial glucose metabolism on bytownite feldspar dissolution rates between 5° and 35°C

    Science.gov (United States)

    Welch, S. A.; Ullman, W. J.

    1999-10-01

    The rate of Si release from dissolving bytownite feldspar in abiotic batch reactors increased as temperatures increased from 5° to 35°C. Metabolically inert subsurface bacteria (bacteria in solution with no organic substrate) had no apparent effect on dissolution rates over this temperature range. When glucose was added to the microbial cultures, the bacteria responded by producing gluconic acid, which catalyzed the dissolution reaction by both proton- and ligand-promoted mechanisms. The metabolic production, excretion, and consumption of gluconic acid in the course of glucose oxidation, and therefore, the degree of microbial enhancement of mineral dissolution, depend on temperature. There was little accumulation of gluconic acid and therefore, no significant enhancement of mineral dissolution rates at 35°C compared to the abiotic controls. At 20°C, gluconate accumulated in the experimental solutions only at the beginning of the experiment and led to a twofold increase in dissolved Si release compared to the controls, primarily by the ligand-promoted dissolution mechanism. There was significant accumulation of gluconic acid in the 5°C experiment, which is reflected in a significant reduction in pH, leading to 20-fold increase in Si release, primarily attributable to the proton-promoted dissolution mechanism. These results indicate that bacteria and microbial metabolism can affect mineral dissolution rates in organic-rich, nutrient-poor environments; the impact of microbial metabolism on aluminum silicate dissolution rates may be greater at lower rather than at higher temperatures due to the metabolic accumulation of dissolution-enhancing protons and ligands in solution.

  11. Platinum-group elements in the cores of potassium feldspar spherules from the Cretaceous-Tertiary boundary at Caravaca (Spain

    Directory of Open Access Journals (Sweden)

    Palomo, I.

    1994-04-01

    Full Text Available The abundant spherules present in the Cretaceous-Tertiary boundary layer at Caravaca are diagenetically transformed to potassium feldspar. Before our study no possible relicts of the precursor material had been reported. but in this paper we describe the presence of cores in these spherules that could represent a relict of the «unknown precursor». These cores are made up of C mixed with Si. Mg. AL Cr. Ca among other elements. Laser Ablation System analysis also reveals an enrichment in pe;E could suggest an extraterrestrial origin for this material. PI. Pd and Ir do not show a chondritic ratio: however. asevere modification of their concentration could be expected during the early diagenetic processes.Las esférulas existentes en la lámina de sedimento del tránsito Cretácico-Terciario de la sección de Caravaca han sido transformadas diagenéticamente a feldespato potásico. En este trabajo se describe la existencia de núcleos encontrados en el interior de las esférulas. los cuales' pueden representar relictos del material precursor. Dichos núcleos están constituidos por C. Si. Mg, AL Cr y Ca entre otros elementos. Se pone de relieve, por vez primera, su notable enriquecimiento en elementos del grupo del platino, cuyas relaciones no condríticas pueden ser debidas a la existencia de importantes modificaciones en su concentración inicial causadas por los procesos diagenéticos y por la existencia de materia orgánica.

  12. Effect of Anti-freezing Admixtures on Alkali-silica Reaction in Mortars

    Institute of Scientific and Technical Information of China (English)

    LIU Junzhe; LI Yushun; LV Lihua

    2005-01-01

    The influence of anti-freezing admixture on the alkali aggregate reaction in mortar was analyzed with accelerated methods. It is confirmed that the addition of sodium salt ingredients of anti-freezing admixture accelerates the alkali silica reaction to some extent, whereas calcium salt ingredient of anti-freezing admixture reduces the expansion of alkali silica reaction caused by high alkali cement. It is found that the addition of the fly ash considerably suppresses the expansion of alkali silica reaction induced by the anti-freezing admixtures.

  13. cobalt (ii), nickel (ii)

    African Journals Online (AJOL)

    DR. AMINU

    ABSTRACT. The manganese (II), cobalt (II), nickel (II) and copper (II) complexes of N, N' – ... temperature and coordinated water were determined ... indicating fairly stable complex compounds (Table 1). The complex compounds are insoluble [Table 2] in water and common organic solvents, but are readily soluble in ...

  14. Process for carbonaceous material conversion and recovery of alkali metal catalyst constituents held by ion exchange sites in conversion residue

    Science.gov (United States)

    Sharp, David W.

    1980-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced, alkali metal constituents are recovered for the particles by contacting or washing them with an aqueous solution containing calcium or magnesium ions in an alkali metal recovery zone at a low temperature, preferably below about 249.degree. F. During the washing or leaching process, the calcium or magnesium ions displace alkali metal ions held by ion exchange sites in the particles thereby liberating the ions and producing an aqueous effluent containing alkali metal constituents. The aqueous effluent from the alkali metal recovery zone is then recycled to the conversion process where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst.

  15. Isothermal thermoluminescence dating of K-feldspar from sediments to determine fault slip rates: development and assessment

    Science.gov (United States)

    Rhodes, E. J.; Roder, B. J.; Lawson, M. J.; Dolan, J. F.; McGill, S. F.; McAuliffe, L.

    2012-04-01

    Faults in California accommodate most of the relative motion between the Pacific and North American tectonic plates, along either one main strike-slip fault, - the San Andreas fault - or a network of sub-parallel faults (e.g., the San Jacinto, Elsinore and San Andreas faults). Slip is also accommodated along many other associated faults and folds, and the region suffers frequent damaging earthquakes. Contemporary movements of different fault-bounded blocks are relatively well established on decadal timescales using remote sensing and GPS, and on timescales of 106 to 107 years, by dating offset geologic features with radiometric methods. However, on timescales of decades to several hundred thousand years, determining total fault offset and mean slip rate is harder. Critical questions for understanding fault dynamics and improving earthquake risk assessment include the degree to which slip is clustered into episodes of more rapid movement, and how slip is accommodated by different sub-parallel faults. In many cases, streams with offset courses can be recognised, and in some cases offset terrace surfaces can be located, especially when using LiDAR data to complement field mapping. Radiocarbon and terrestrial cosmogenic nuclides have been used to date these features, but both have limitations of age range, sample suitability and availability. OSL (optically stimulated luminescence) and IRSL (infra-red stimulated luminescence) have great potential to complement these techniques, though the characteristics of quartz in some parts of southern California are suboptimal, displaying low sensitivity and other limitations. In order to overcome these limitations encountered using quartz OSL, we are developing a new geochronometer based on the isothermal thermoluminescence (ITL) signal of K feldspar measured at 250°C. Preliminary ITL age estimates from the paleoseismic site of El Paso Peaks on the Central Garlock fault in the Mojave Desert, California, agree well with a well

  16. Generation and characterization of alkali metal clusters in Y-FAU zeolites. An ESR and MAS NMR spectroscopic study

    Science.gov (United States)

    Hannus, István; Béres, Attila; Nagy, János B.; Halász, János; Kiricsi, Imre

    1997-06-01

    Charged and neutral metal clusters of various compositions and sizes can be prepared by controlling the alkali metal content by the decomposition of alkali azides and the composition of the host zeolite by ion-exchange. ESR signals show that electron transfer from alkali metal atoms to alkali metal cations does occur, but in a direction opposite to that predicted by the gas-phase thermochemistry. Alkali metal clusters proved to be very active basic catalytic centers.

  17. Calc-alkali rocks derived from tholeiite magma in Hakone volcano; pyroxene crystallization trends and pyroxene geothermometry to estimate the magma temperature

    Science.gov (United States)

    Ishii, T.

    2012-12-01

    Calc-alkali rocks are widely distributed in the island arcs. The several models of their magma-genesis were proposed by many geoscientists (e.g. Kuno 1950, Osborn 1959, Sakuyama 1981, Tatsumi 2011) on the bases of precise petrological investigations. Crystallization trends of rock forming minerals (pyroxene, feldspar etc.) in the individual lava flow of the hydrous tholeiitic magma are represented by chemical zoning from phenocryst through microphenocryst to the groundmass in each lava. Those trends indicate degassing (or dehydrating) trends of erupted lava (Ishii 1991). Crystallization trend of minerals of hydrous magma in the subvolcanic magma reservoir is represented by core of phenocrysts throughout lava-flow strata in each volcano. Those trends indicate water-enrichment (or hydrating) trend in the magma reservoir. On the bases of the detailed analyses of the pyroxene crystallization sequences as well as estimated magmatic temperatures using pyroxene geothermometer, for calc-alkali rocks from the Central Cone (CC) in the Hakone volcano, the following working hypothesis is suggested, i.e. those calc-alkali rocks are induced by magma mixing between high temperature (about 1120 Degree Centigrade) tholeiite magma and low temperature (about 970 Degree Centigrade) magma, the latter is originated from fractional crystallization of the primitive high temperature hydras island-arc tholeiite magma within magma reservoir under closed environment for water. Reference Ishii, T., 1991. Lava-flow and subvolcanic magma reservoir composition trends in the Ca-poor pyroxenes of Hakone Volcano, Japan. Jour. Petrol., 32, 429-450 Kuno, H., 1950. Petrology of Hakone volcano and the adjacent areas, Japan. Bull. Geol. Soc. Am., 61, 957-1019. Sakuyama, M., 1981. Petrological study of the Myoko and Kurohime volcanoes, Japan: crystallization sequence and evidence for magma mixing. Jour. Petrol., 22, 553-583. Osborn, E. F., 1959. Role of oxygen pressure in the crystallization and

  18. Positronium-alkali atom scattering at medium energies

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, Ajoy [Laban Hrad Vidyapith, AD-369, Salt Lake City, Kolkata 700 064 (India); Basu, Arindam [Department of Physics, Maheshtala College, Chandannagar, South 24 Parganas, Kolkata 700 140 (India); Sarkar, Nirmal K [Sodepur Chandrachur Vidyapith, 1, Desh Bandhu Nagar, Sodepur, 743 174 (India); Sinha, Prabal K [Department of Physics, Bangabasi College, 19, Raj Kumar Chakravorty Sarani, Kolkata 700 009 (India)

    2004-04-28

    We investigate the scattering of orthopositronium (o-Ps) atom off different atomic alkali targets (Na to Cs) at low and medium energies (up to 120 eV). Projectile-elastic and target-elastic close-coupling models have been employed to investigate the systems in addition to the static-exchange model. Elastic, excitation and total cross sections have been reported for all four systems. The magnitude of the alkali excitation cross section increases with increasing atomic number of the target atom while the position of the peak value shifts towards lower incident energies. The magnitudes of the Ps excitation and ionization cross sections increase steadily with atomic number with no change in the peak position. The reported results show regular behaviour with increasing atomic number of the target atom. Scattering parameters for the Ps-Rb and Ps-Cs systems are being reported for the first time.

  19. PREPARATION OF HOLLOW LATEX PARTICLES BY ALKALI-ACID TREATMENT

    Institute of Scientific and Technical Information of China (English)

    郝冬梅; 王新灵; 朱卫华; 唐小真; 刘成岑; 施凯

    2001-01-01

    Hollow polymer latex particles were prepared by seeded emulsion polymerization. A seed latex consisting of styrene (St), butyl acrylate(BA) copolymer was first prepared, and seeded terpolymerization of St-BA-MA(methacrylic acid) were then carried out in the absence of surfactant. Final latex was treated by a two-step treatment under alkaline and acidic conditions, thus, the particles with hollow structure were obtained. We discussed the effects of pH value, temperature and time in alkali and acid treatment processes on hollow structure within the polymer latex particles and amount of carboxylic group on particle surface. The results show that the hollow polymer latex particles with the largest hollow size can be obtained under a certain condition (pH12.5, 90°C, 3 h in alkali treatment stage and pH2.5, 85°C, 3 h in acid treatment stage).

  20. Fracture properties of concrete specimens made from alkali activated binders

    Science.gov (United States)

    Šimonová, Hana; Kucharczyková, Barbara; Topolář, Libor; Bílek, Vlastimil, Jr.; Keršner, Zbyněk

    2017-09-01

    The aim of this paper is to quantify crack initiation and other fracture properties – effective fracture toughness and specific fracture energy – of two types of concrete with an alkali activated binder. The beam specimens with a stress concentrator were tested in a three-point bending test after 28, 90, and 365 days of maturing. Records of fracture tests in the form of load versus deflection (P–d) diagrams were evaluated using effective crack model and work-of-fracture method and load versus mouth crack opening displacement (P–CMOD) diagrams were evaluated using the Double-K fracture model. The initiation of cracks during the fracture tests for all ages was also monitored by the acoustic emission method. The higher value of monitored mechanical fracture parameters of concrete with alkali activated blast furnace slag were achieved with substitution blast furnace slag by low calcium fly ash in comparison with substitution by cement kiln dust.

  1. Coherent coupling of alkali atoms by random collisions

    CERN Document Server

    Katz, Or; Firstenberg, Ofer

    2015-01-01

    Random spin-exchange collisions in warm alkali vapor cause rapid decoherence and act to equilibriate the spin state of the atoms. In contrast, here we demonstrate experimentally and theoretically a coherent coupling of one alkali specie to another specie, mediated by these random collisions. We show that, the minor specie (potassium) inherits the magnetic properties of the dominant specie (rubidium), including its lifetime (T1), coherence time (T2), gyromagnetic ratio, and SERF magnetic-field threshold. We further show that this coupling can be completely controlled by varying the strength of the magnetic field. Finally, we explain these phenomena analytically by modes-mixing of the two species via spin-exchange collisions.

  2. Alkali elements in the Earth's core: Evidence from enstatite meteorites

    Science.gov (United States)

    Lodders, K.

    1995-01-01

    The abundances of alkali elements in the Earth's core are predicted by assuming that accretion of the Earth started from material similar in composition to enstatite chondrites and that enstatite achondrites (aubrites) provide a natural laboratory to study core-mantle differentiation under extremely reducing conditions. If core formation on the aubrite parent body is comparable with core formation on the early Earth, it is found that 2600 (+/- 1000) ppm Na, 550 (+/- 260) ppm K, 3.4 (+/- 2.1) ppm Rb, and 0.31 (+/- 0.24) ppm Cs can reside in the Earth's core. The alkali-element abundances are consistent with those predicted by independent estimates based on nebula condensation calculations and heat flow data.

  3. Alkali halide microstructured optical fiber for X-ray detection

    Energy Technology Data Exchange (ETDEWEB)

    DeHaven, S. L., E-mail: stanton.l.dehaven@nasa.gov, E-mail: russel.a.wincheski@nasa.gov; Wincheski, R. A., E-mail: stanton.l.dehaven@nasa.gov, E-mail: russel.a.wincheski@nasa.gov [NASA Langley Research Center, Hampton, VA 23681 (United States); Albin, S., E-mail: salbin@nsu.edu [Norfolk State University, Norfolk, VA 23504 (United States)

    2015-03-31

    Microstructured optical fibers containing alkali halide scintillation materials of CsI(Na), CsI(Tl), and NaI(Tl) are presented. The scintillation materials are grown inside the microstructured fibers using a modified Bridgman-Stockbarger technique. The x-ray photon counts of these fibers, with and without an aluminum film coating are compared to the output of a collimated CdTe solid state detector over an energy range from 10 to 40 keV. The photon count results show significant variations in the fiber output based on the materials. The alkali halide fiber output can exceed that of the CdTe detector, dependent upon photon counter efficiency and fiber configuration. The results and associated materials difference are discussed.

  4. The optical properties of alkali nitrate single crystals

    Science.gov (United States)

    Anan'ev, Vladimir; Miklin, Mikhail

    2000-08-01

    Absorption of non-polarized light by a uniaxial crystal has been studied. The degree of absorption polarization has been calculated as a function of the ratio of optical densities in the region of low and high absorbances. This function is proposed for analysis of the qualitative and quantitative characteristics of uniaxial crystal absorption spectra. Non-polarized light spectra of alkali nitrate single crystals, both pure and doped with thallium, have been studied. It is shown that the absorption band at 300 nm is due to two transitions, whose intensities depend on temperature in various ways. There is a weak band in a short wavelength range of the absorption spectrum of potassium nitrate crystal, whose intensity increases with thallium doping. The band parameters of alkali nitrate single crystals have been calculated. Low-energy transitions in the nitrate ion have been located.

  5. Alkali-helium snowball complexes formed on helium nanodroplets.

    Science.gov (United States)

    Müller, S; Mudrich, M; Stienkemeier, F

    2009-07-28

    We systematically investigate the formation and stability of snowballs formed by femtosecond photoionization of small alkali clusters bound to helium nanodroplets. For all studied alkali species Ak = (Na,K,Rb,Cs) we observe the formation of snowballs Ak(+)He(N) when multiply doping the droplets. Fragmentation of clusters Ak(N) upon ionization appears to enhance snowball formation. In the case of Na and Cs we also detect snowballs Ak(2) (+)He(N) formed around Ak dimer ions. While the snowball progression for Na and K is limited to less than 11 helium atoms, the heavier atoms Rb and Cs feature wide distributions at least up to Ak(+)He(41). Characteristic steps in the mass spectra of Cs-doped helium droplets are found at positions consistent with predictions on the closure of the first shell of helium atoms around the Ak(+) ion based on variational Monte Carlo simulations.

  6. Coherent coupling of alkali atoms by random collisions.

    Science.gov (United States)

    Katz, Or; Peleg, Or; Firstenberg, Ofer

    2015-09-11

    Random spin-exchange collisions in warm alkali vapor cause rapid decoherence and act to equilibrate the spin state of the atoms in the vapor. In contrast, here we demonstrate experimentally and theoretically a coherent coupling of one alkali species to another species, mediated by these random collisions. We show that the minor species (potassium) inherits the magnetic properties of the dominant species (rubidium), including its lifetime (T_{1}), coherence time (T_{2}), gyromagnetic ratio, and spin-exchange relaxation-free magnetic-field threshold. We further show that this coupling can be completely controlled by varying the strength of the magnetic field. Finally, we explain these phenomena analytically by mode mixing of the two species via spin-exchange collisions.

  7. Penetration of alkali atoms throughout a graphene membrane: theoretical modeling.

    Science.gov (United States)

    Boukhvalov, D W; Virojanadara, C

    2012-03-07

    Theoretical studies of penetration of various alkali atoms (Li, Na, Rb, Cs) throughout a graphene membrane grown on a silicon carbide substrate are reported and compared with recent experimental results. Results of first principles modeling demonstrate a rather low (about 0.8 eV) energy barrier for the formation of temporary defects in the carbon layer required for the penetration of Li at a high concentration of adatoms, a higher (about 2 eV) barrier for Na, and barriers above 4 eV for Rb and Cs. Experiments prove migration of lithium adatoms from the graphene surface to the buffer layer and SiC substrate at room temperature, sodium at 100 °C and impenetrability of the graphene membrane for Rb and Cs. Differences between epitaxial and free-standing graphene for the penetration of alkali ions are also discussed.

  8. Polarizabilities and hyperpolarizabilities of the alkali metal atoms

    Energy Technology Data Exchange (ETDEWEB)

    Fuentealba, P. (Chile Univ., Santiago (Chile). Departamento de Fisica and Centro de Mecanica Cuantica Aplicada (CMCA)); Reyes, O. (Chile Univ., Santiago (Chile). Dept. de Fisica)

    1993-08-14

    The electric static dipole polarizability [alpha], quadrupole polarizability C, dipole-quadrupole polarizability B, and the second dipole hyperpolarizability [gamma] have been calculated for the alkali metal atoms in the ground state. The results are based on a pseudopotential which is able to incorporate the very important core-valence correlation effect through a core polarization potential, and, in an empirical way, the main relativistic effects. The calculated properties compare very well with more elaborated calculations for the Li atom, excepting the second hyperpolarizability [gamma]. For the other atoms, there is neither theoretical nor experimental information about most of the higher polarizabilities. Hence, the results of this paper should be seen as a first attempt to give a complete account of the series expansion of the interaction energy of an alkali metal atom and a static electric field. (author).

  9. Alkali Halide Microstructured Optical Fiber for X-Ray Detection

    Science.gov (United States)

    DeHaven, S. L.; Wincheski, R. A.; Albin, S.

    2014-01-01

    Microstructured optical fibers containing alkali halide scintillation materials of CsI(Na), CsI(Tl), and NaI(Tl) are presented. The scintillation materials are grown inside the microstructured fibers using a modified Bridgman-Stockbarger technique. The x-ray photon counts of these fibers, with and without an aluminum film coating are compared to the output of a collimated CdTe solid state detector over an energy range from 10 to 40 keV. The photon count results show significant variations in the fiber output based on the materials. The alkali halide fiber output can exceed that of the CdTe detector, dependent upon photon counter efficiency and fiber configuration. The results and associated materials difference are discussed.

  10. Density functional study of ferromagnetism in alkali metal thin films

    Indian Academy of Sciences (India)

    Prasenjit Sen

    2010-04-01

    Electronic and magnetic structures of (1 0 0) films of K and Cs, having thicknesses of one to seven layers, are calculated within the plane-wave projector augmented wave (PAW) formalism of the density functional theory (DFT), using both local spin density approximation (LSDA) and the PW91 generalized gradient approximation (GGA). Only a six-layer Cs film is found to have a ferromagnetic (FM) state which is degenerate with a paramagnetic (PM) state within the accuracy of these calculations. These results are compared with those obtained from calculations on a finite-thickness uniform jellium model (UJM), and it is argued that within LSDA or GGA, alkali metal thin films cannot be claimed to have an FM ground state. Relevance of these results to the experiments on transition metal-doped alkali metal thin films and bulk hosts are also discussed.

  11. Solubility of 1:1 Alkali Nitrates and Chlorides in Near-Critical and Supercritical Water : 1 Alkali Nitrates and Chlorides in Near-Critical and Supercritical Water

    NARCIS (Netherlands)

    Leusbrock, Ingo; Metz, Sybrand J.; Rexwinkel, Glenn; Versteeg, Geert F.

    2009-01-01

    To increase the available data oil systems containing supercritical water and inorganic compounds, all experimental setup was designed to investigate the solubilities of inorganic compounds Ill supercritical water, In this work, three alkali chloride salts (LiCl, NaCl, KCl) and three alkali nitrate

  12. On-line alkali monitoring - Part 1; Kontinuerlig alkalimaetning - Etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Christer; Ljung, P.; Woxlin, H.

    1997-02-01

    As a consequence of the increased knowledge of the environmental impact of combustion based heat and power generation, the use of renewable biofuels will be increased. An obstacle associated to biofuel combustion compared to other fuels is the large release of alkali. Alkali compounds in flue gases are known to cause severe operational problems. Three of the major problems are; fouling of superheating tubes (causing reduced heat transfer and possibly corrosion), agglomeration of the bed material in fluidized beds, and poisoning of SCR catalysts. Yet another alkali related problem arises when, in order to increase the electric efficiency of combustion power plants, combined-cycle technology is used. Alkali vapour present in the fuel gas for the gas turbine is condensed to particles which increase corrosion and erosion of the turbine blades. The research on ash related operational problems has to be extended in order to ensure future use of biofuels in heat and power generation. In all successful research, adequate tools are necessary. To investigate ash related problems the key issue is to be able to perform continuous alkali measurements. This pilot study has investigated the need of continuous alkali measurements, which alkali species are harmful in the different applications and also available instrumentation capable of measuring the specific alkali species. The report gives a short summary presenting alkali related operational problems. In addition a schematic overview is given, showing the alkali species that possibly can exist in various parts of the power plant. 48 refs, 13 figs, 4 tabs

  13. Co-digestion of grass silage and cow manure in a CSTR by re-circulation of alkali treated solids of the digestate.

    Science.gov (United States)

    Jagadabhi, P S; Lehtomäki, A; Rintala, J

    2008-10-01

    Three laboratory, continuously stirred tank reactors (CSTRs) co-digesting grass silage and cow manure (forming 30% and 70% of substrate volatile solids (VS), respectively) were operated to evaluate the effects of re-circulating an alkali-treated and untreated solid fraction of the digestate back to the reactors. The CSTRs were operated at an organic loading rate (OLR) of 2 kg VS m(-3) day(-1) and hydraulic retention time (HRT) of 20 days with a semi-continuous mode of feeding. The feasibility of co-digestion with substrate VS containing 30% VS of crop was reinforced, resulting in average specific methane yield of about 180-185 1 CH4 kg(-1) VS. Re-circulation of the solid fraction of digestate back to the reactors in both alkali-treated and untreated forms decreased the methane yield by 11% and 21%, respectively, and resulted in operational problems such as scum formation and accumulation of the reactor materials. Batch studies were conducted to evaluate (i) the methane potentials of the solid fraction of digestate, and whole digestate with alkali treatments ranging from 20-60 g NaOH kg(-1) VS of substrate, and (ii) methane potentials of the accumulated reactor materials as top, middle and bottom layers. The solid fraction of digestate treated with 20 g NaOH kg(-1) VS showed higher specific methane yield (340 l CH4 kg(-1) VS) than the higher range of alkali treatments. The bottom layers of the control reactor and the reactor fed with alkali-treated solids gave a higher specific methane yield (93 and 85 l CH4 kg(-1) VS, respectively), and all three layers of untreated solids gave similar methane potentials.

  14. Efficient potassium diode pumped alkali laser operating in pulsed mode.

    Science.gov (United States)

    Zhdanov, Boris V; Rotondaro, Matthew D; Shaffer, Michael K; Knize, Randall J

    2014-07-14

    This paper presents the results of our experiments on the development of an efficient hydrocarbon free diode pumped alkali laser based on potassium vapor buffered by He gas at 600 Torr. A slope efficiency of more than 50% was demonstrated with a total optical conversion efficiency of 30%. This result was achieved by using a narrowband diode laser stack as the pump source. The stack was operated in pulsed mode to avoid limiting thermal effects and ionization.

  15. Antacids, Altered Mental Status, and Milk-Alkali Syndrome

    Directory of Open Access Journals (Sweden)

    Simon C. Watson

    2012-01-01

    Full Text Available The frequency of milk-alkali syndrome decreased rapidly after the development of histamine-2 antagonists and proton pump inhibitors for the treatment of peptic ulcer disease; however, the availability and overconsumption of antacids and calcium supplements can still place patients at risk (D. P. Beall et al., 2006. Here we describe a patient who presented with altered mental status, hypercalcemia, metabolic alkalosis, and acute renal failure in the context of ingesting large amounts of antacids to control dyspepsia.

  16. Pair potential trend of alkali metals under external pressure

    Science.gov (United States)

    Rahman, S. M. Mujibur

    1987-09-01

    Structural phase stability of certain alkali metals under external pressure is investigated by looking at their pair potential trend. The effective pair potentials occurring in the real space representation of the band structure contribution relevant to a second-order theory are calculated by using an appropriate dielectric function and a simple empty-core pseudopotential. The relative positions of the neighboring atoms with respect to the minima in the pair potentials uphold a qualitative picture of the phase stability in these systems.

  17. Ultrafine microporous and mesoporous activated carbon fibers from alkali lignin

    OpenAIRE

    2013-01-01

    A facile and sustainable approach has been successfully devised to fabricate ultrafine (100-500 nm) highly porous activated carbon fibers (ACFs) by electrospinning of aqueous solutions of predominantly alkali lignin (low sulfonate content) followed by simultaneous carbonization and activation at 850 °C under N2. Incorporating a polyethylene oxide (PEO) carrier with only up to one ninth of lignin not only enabled efficient electrospinning into fibers but also retained fibrous structures during...

  18. A hidden history of heartburn: The milk-alkali syndrome

    OpenAIRE

    2011-01-01

    Milk-alkali syndrome was once considered to be of historic interest and a rare cause of hypercalcemia. Currently, it should be an important consideration in the differential diagnosis of hypercalcemia, after malignancies and primary hyperparathyroidism. The resurgence is in part due to the easy availability of over the counter (OTC) calcium preparations. We describe a 50-year-old man who presented with severe hypercalcemia on two occasions associated with renal failure and metabolic alkalosis...

  19. Composition and thermodynamic properties of dense alkali metal plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Gabdullin, M.T. [NNLOT, al-Farabi Kazakh National University, 71 al-Farabi Str., Almaty 050035 (Kazakhstan); Ramazanov, T.S.; Dzhumagulova, K.N. [IETP, al-Farabi Kazakh National University, 71 al-Farabi Str., Almaty 050035 (Kazakhstan)

    2012-04-15

    In this work composition and thermodynamic properties of dense alkali metal plasmas (Li, Na) were investigated. Composition was derived by solving the Saha equations with corrections due to nonideality. The lowering of the ionization potentials was calculated on the basis of pseudopotentials by taking screening and quantum effects into account (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  20. Engineering Properties of Alkali-Activated Fly Ash Concrete

    OpenAIRE

    2006-01-01

    This paper reports the results of experimental research on certain engineering properties of a new (portland cement-free) concrete made with alkali-activated fly ash. Laboratory tests were conducted to determine its (bending and compression) mechanical strength, modulus of elasticity, bond strength, and shrinkage. The results show that mortar and concrete made with portland cement-free activated fly ash develop a high mechanical strength in short periods of time, have a moderate modulus of el...

  1. Effect of alkali treatment on surface morphology of titanium

    Energy Technology Data Exchange (ETDEWEB)

    Tan, K. J., E-mail: gd130056@siswa.uthm.edu.my; Wahab, M. A. A., E-mail: cd110006@siswa.uthm.edu.my; Mahmod, S., E-mail: cd110201@siswa.uthm.edu.my; Idris, M. I., E-mail: izwana@uthm.edu.my; Abdullah, H. Z., E-mail: hasan@uthm.edu.my [Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor (Malaysia)

    2015-07-22

    Alkali and heat treatments were first introduced by Kim et al. to prepare a bioactive surface on titanium. This method has been proven very effective and widely used in other studies to promote titanium osteointegration. This study aims to investigate further the effect of alkali treatment on surface morphology of high purity titanium. High purity titanium foils were immersed in NaOH aqueous solutions of 0.5 M, 5 M and 15 M at 60°C and 80 °C for 1, 3 and 7 days. The surface morphology was examined using Field Emission Scanning Electron Microscope (FESEM). The obtained phases were analysed using Fourier Transform Infrared Spectroscopy (FTIR) in the spectra range of 4000-600 cm{sup −1} at 4 cm{sup −1} resolution and 50 scans. At the same soaking temperature and soaking time, a thicker porous network was observed with increasing concentration of NaOH. At the same soaking temperature, a much porous structure was observed with increasing soaking time. At constant alkali concentration, more homogenously distributed porous surface structure was observed with increasing soaking temperature.

  2. Superconductivity in alkali-doped C{sub 60}

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, Arthur P., E-mail: apr@ucsc.edu

    2015-07-15

    Highlight: • Superconductivity in alkali-doped C{sub 60} (A{sub 3}C{sub 60}) is well described by an s-wave state produced by phonon mediated pairing. • Moderate coupling of electrons to high-frequency shape-changing intra-molecular vibrational modes produces transition temperatures up to 33 K in single-phase material. • The good understanding of pairing in A{sub 3}C{sub 60} offers a paradigm for the development of new superconducting materials. - Abstract: Superconductivity in alkali-doped C{sub 60} (A{sub 3}C{sub 60}, A = an alkali atom) is well described by an s-wave state produced by phonon mediated pairing. Moderate coupling of electrons to high-frequency shape-changing intra-molecular vibrational modes produces transition temperatures (T{sub c}) up to 33 K in single-phase material. The good understanding of pairing in A{sub 3}C{sub 60} offers a paradigm for the development of new superconducting materials.

  3. The unexpected properties of alkali metal iron selenide superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Dagotto, Elbio R [ORNL

    2013-01-01

    The iron-based superconductors that contain FeAs layers as the fundamental building block in the crystal structures have been rationalized in the past using ideas based on the Fermi surface nesting of hole and electron pockets when in the presence of weak Hubbard U interactions. This approach seemed appropriate considering the small values of the magnetic moments in the parent compounds and the clear evidence based on photoemission experiments of the required electron and hole pockets. However, recent results in the context of alkali metal iron selenides, with generic chemical composition AxFe2ySe2 (A alkali metal element), have challenged those previous ideas since at particular compositions y the low-temperature ground states are insulating and display antiferromagnetic order with large iron magnetic moments. Moreover, angle-resolved photoemission studies have revealed the absence of hole pockets at the Fermi level in these materials. The present status of this exciting area of research, with the potential to alter conceptually our understanding of the ironbased superconductors, is here reviewed, covering both experimental and theoretical investigations. Other recent related developments are also briefly reviewed, such as the study of selenide two-leg ladders and the discovery of superconductivity in a single layer of FeSe. The conceptual issues considered established for the alkali metal iron selenides, as well as several issues that still require further work, are discussed.

  4. The structure of liquid alkali nitrates and nitrites

    Energy Technology Data Exchange (ETDEWEB)

    Wilding, Martin C.; Wilson, Mark; Ribeiro, Mauro; Benmore, Chris J.; Weber, J K; Alderman, Oliver; Tamalonis, Anthony; Parise, J. B.

    2017-08-28

    High energy X-ray diffraction has been combined with containerless techniques to determine the structure of a series of alkali and ammonium nitrate and nitrite liquids. The systems have been modelled using molecular dynamics simulation which allows for the flexibility of, and movement of charge within, the molecular anions. The model reproduces the experimentally-determined scattering functions in both the low-and high-Q regimes reflecting the inter-and intra-molecular length-scales. For ammonium nitrate the best fit to the diffraction data is obtained by assuming the NH4+ cation to have a radius closer to that for Cs+ rather than a smaller cation such as Rb+ as often previously assumed. The alkali nitrites show an emergent length scale, attributed to the nitrogen-nitrogen spatial correlations, that depends on both temperature and the identity of the alkali cation. The corresponding nitrates show a more subtle effect in the nitrogen-nitrogen correlations. As a result, the nature of this N-N length-scale appears different for the respective nitrites and nitrates.

  5. Electron densities and alkali atoms in exoplanet atmospheres

    Energy Technology Data Exchange (ETDEWEB)

    Lavvas, P. [GSMA, Université de Reims Champagne Ardenne, CNRS UMR 7331, Reims, 51687 France (France); Koskinen, T.; Yelle, R. V., E-mail: panayotis.lavvas@univ-reims.fr [Lunar and Planetary Laboratory, University of Arizona, Tucson, AZ 85719 (United States)

    2014-11-20

    We describe a detailed study on the properties of alkali atoms in extrasolar giant planets, and specifically focus on their role in generating the atmospheric free electron densities, as well as their impact on the transit depth observations. We focus our study on the case of HD 209458b, and we show that photoionization produces a large electron density in the middle atmosphere that is about two orders of magnitude larger than the density anticipated from thermal ionization. Our purely photochemical calculations, though, result in a much larger transit depth for K than observed for this planet. This result does not change even if the roles of molecular chemistry and excited state chemistry are considered for the alkali atoms. In contrast, the model results for the case of exoplanet XO-2b are in good agreement with the available observations. Given these results we discuss other possible scenarios, such as changes in the elemental abundances, changes in the temperature profiles, and the possible presence of clouds, which could potentially explain the observed HD 209458b alkali properties. We find that most of these scenarios cannot explain the observations, with the exception of a heterogeneous source (i.e., clouds or aerosols) under specific conditions, but we also note the discrepancies among the available observations.

  6. The Interfacial Transition Zone in Alkali-Activated Slag Mortars

    Directory of Open Access Journals (Sweden)

    Rackel eSan Nicolas

    2015-12-01

    Full Text Available The interfacial transition zone (ITZ is known to strongly influence the mechanical and transport properties of mortars and concretes. This paper studies the ITZ between siliceous (quartz aggregates and alkali activated slag binders in the context of mortar specimens. Backscattered electron images (BSE generated in an environmental scanning electron microscope (ESEM are used to identify unreacted binder components, reaction products and porosity in the zone surrounding aggregate particles, by composition and density contrast. X-ray mapping is used to exclude the regions corresponding to the aggregates from the BSE image of the ITZ, thus enabling analysis of only the binder phases, which are segmented into binary images by grey level discrimination. A distinct yet dense ITZ region is present in the alkali-activated slag mortars, containing a reduced content of unreacted slag particles compared to the bulk binder. The elemental analysis of this region shows that it contains a (C,N-A-S-H gel which seems to have a higher content of Na (potentially deposited through desiccation of the pore solution and a lower content of Ca than the bulk inner and outer products forming in the main binding region. These differences are potentially important in terms of long-term concrete performance, as the absence of a highly porous interfacial transition zone region is expected to provide a positive influence on the mechanical and transport properties of alkali-activated slag concretes.

  7. Scattering of positrons and electrons by alkali atoms

    Science.gov (United States)

    Stein, T. S.; Kauppila, W. E.; Kwan, C. K.; Lukaszew, R. A.; Parikh, S. P.; Wan, Y. J.; Zhou, S.; Dababneh, M. S.

    1990-01-01

    Absolute total scattering cross sections (Q sub T's) were measured for positrons and electrons colliding with sodium, potassium, and rubidium in the 1 to 102 eV range, using the same apparatus and experimental approach (a beam transmission technique) for both projectiles. The present results for positron-sodium and -rubidium collisions represent the first Q sub T measurements reported for these collision systems. Features which distinguish the present comparisons between positron- and electron-alkali atom Q sub T's from those for other atoms and molecules (room-temperature gases) which have been used as targets for positrons and electrons are the proximity of the corresponding positron- and electron-alkali atom Q sub T's over the entire energy range of overlap, with an indication of a merging or near-merging of the corresponding positron and electron Q sub T's near (and above) the relatively low energy of about 40 eV, and a general tendency for the positron-alkali atom Q sub T's to be higher than the corresponding electron values as the projectile energy is decreased below about 40 eV.

  8. Plasma formation in diode pumped alkali lasers sustained in Cs

    Science.gov (United States)

    Markosyan, Aram H.; Kushner, Mark J.

    2016-11-01

    In diode pumped alkali lasers (DPALs), lasing action occurs on the resonant lines of alkali atoms following pumping by broadband semiconductor lasers. The goal is to convert the efficient but usually poor optical quality of inexpensive diode lasers into the high optical quality of atomic vapor lasers. Resonant excitation of alkali vapor leads to plasma formation through the excitation transfer from the 2P states to upper lying states, which then are photoionized by the pump and intracavity radiation. A first principles global model was developed to investigate the operation of the He/Cs DPAL system and the consequences of plasma formation on the efficiency of the laser. Over a range of pump powers, cell temperatures, excitation frequency, and mole fraction of the collision mixing agent (N2 or C2H6), we found that sufficient plasma formation can occur that the Cs vapor is depleted. Although N2 is not a favored collisional mixing agent due to large rates of quenching of the 2P states, we found a range of pump parameters where laser oscillation may occur. The poor performance of N2 buffered systems may be explained in part by plasma formation. We found that during the operation of the DPAL system with N2 as the collisional mixing agent, plasma formation is in excess of 1014-1015 cm-3, which can degrade laser output intensity by both depletion of the neutral vapor and electron collisional mixing of the laser levels.

  9. Heterometallic aluminates: alkali metals trapped by an aluminium aryloxide claw.

    Science.gov (United States)

    Muñoz, M Teresa; Cuenca, Tomás; Mosquera, Marta E G

    2014-10-14

    A series of heterometallic aluminium-alkali metal species [AlMMe2{2,6-(MeO)2C6H3O}2]n have been isolated for lithium, sodium and potassium. These compounds can be generated by the reaction of [AlMe2{2,6-(MeO)2C6H3O}]2 with the metallated phenol [M{2,6-(MeO)2C6H3O}]n or through the reaction of the mixture of AlMe3 and the appropriate alkali metal alkyl base with two equivalents of 2,6-dimethoxyphenol. In the heterometallic species obtained, the {AlMe2{2,6-(MeO)2C6H3O}2}(-) moiety is observed and could be described as a claw which fixes the alkali ion by the phenoxide oxygen atoms while the methoxy groups help to stabilize their coordination sphere. All compounds have been characterized by NMR spectroscopy and X-ray diffraction methods. Catalytic studies reveal that these compounds are active in ring-opening polymerization of L-lactide.

  10. Traditional cattle grazing in a mosaic alkali landscape: effects on grassland biodiversity along a moisture gradient.

    Directory of Open Access Journals (Sweden)

    Péter Török

    Full Text Available Extensively managed pastures are of crucial importance in sustaining biodiversity both in local- and landscape-level. Thus, re-introduction of traditional grazing management is a crucial issue in grassland conservation actions worldwide. Traditional grazing with robust cattle breeds in low stocking rates is considered to be especially useful to mimic natural grazing regimes, but well documented case-studies are surprisingly rare on this topic. Our goal was to evaluate the effectiveness of traditional Hungarian Grey cattle grazing as a conservation action in a mosaic alkali landscape. We asked the following questions: (i How does cattle grazing affect species composition and diversity of the grasslands? (ii What are the effects of grazing on short-lived and perennial noxious species? (iii Are there distinct effects of grazing in dry-, mesophilous- and wet grassland types? Vegetation of fenced and grazed plots in a 200-ha sized habitat complex (secondary dry grasslands and pristine mesophilous- and wet alkali grasslands was sampled from 2006-2009 in East-Hungary. We found higher diversity scores in grazed plots compared to fenced ones in mesophilous- and wet grasslands. Higher cover of noxious species was typical in fenced plots compared to their grazed counterparts in the last year in every studied grassland type. We found an increasing effect of grazing from the dry- towards the wet grassland types. The year-to-year differences also followed similar pattern: the site-dependent effects were the lowest in the dry grassland and an increasing effect was detected along the moisture gradient. We found that extensive Hungarian Grey cattle grazing is an effective tool to suppress noxious species and to create a mosaic vegetation structure, which enables to maintain high species richness in the landscape. Hungarian Grey cattle can feed in open habitats along long moisture gradient, thus in highly mosaic landscapes this breed can be the most suitable

  11. Alkali metal cation-hexacyclen complexes: effects of alkali metal cation size on the structure and binding energy.

    Science.gov (United States)

    Austin, C A; Rodgers, M T

    2014-07-24

    Threshold collision-induced dissociation (CID) of alkali metal cation-hexacyclen (ha18C6) complexes, M(+)(ha18C6), with xenon is studied using guided ion beam tandem mass spectrometry techniques. The alkali metal cations examined here include: Na(+), K(+), Rb(+), and Cs(+). In all cases, M(+) is the only product observed, corresponding to endothermic loss of the intact ha18C6 ligand. The cross-section thresholds are analyzed to extract zero and 298 K M(+)-ha18C6 bond dissociation energies (BDEs) after properly accounting for the effects of multiple M(+)(ha18C6)-Xe collisions, the kinetic and internal energy distributions of the M(+)(ha18C6) and Xe reactants, and the lifetimes for dissociation of the activated M(+)(ha18C6) complexes. Ab initio and density functional theory calculations are used to determine the structures of ha18C6 and the M(+)(ha18C6) complexes, provide molecular constants necessary for the thermodynamic analysis of the energy-resolved CID data, and theoretical estimates for the M(+)-ha18C6 BDEs. Calculations using a polarizable continuum model are also performed to examine solvent effects on the binding. In the absence of solvent, the M(+)-ha18C6 BDEs decrease as the size of the alkali metal cation increases, consistent with the noncovalent nature of the binding in these complexes. However, in the presence of solvent, the ha18C6 ligand exhibits selectivity for K(+) over the other alkali metal cations. The M(+)(ha18C6) structures and BDEs are compared to those previously reported for the analogous M(+)(18-crown-6) and M(+)(cyclen) complexes to examine the effects of the nature of the donor atom (N versus O) and the number donor atoms (six vs four) on the nature and strength of binding.

  12. Alternative alkali resistant deNO{sub x} technologies

    Energy Technology Data Exchange (ETDEWEB)

    Buus Kristensen, S.; Due-Hansen, J.; Putluru, S.S.R.; Kunov-Kruse, A.; Fehrmann, R.; Degn Jensen, A.

    2011-04-15

    The aim of the project is to identify, make and test possible alkali resistant deNO{sub x} catalysts for use in biomass, waste or fossil fuelled power plants, where the flue gas typically has a high level of potassium compounds, which rapidly de-activate the traditional V{sub 2}O{sub 5}/TiO{sub 2} catalyst. Furthermore, new technologies are investigated based on a protective coating of the catalyst elements and selective reversible absorption of NO{sub x} with ionic liquids. Several promising alternative deNO{sub x} catalyst types have been made during the project: 1) V, Fe, CU based nano-TiO{sub 2} and nano-TiO{sub 2}-SO{sub 4}{sup 2-} catalysts; 2) V/ZrO{sub 2}-SO{sub 2}- and V/ZrO{sub 2}-CeO{sub 2} catalysts; V, Fe, Cu based Zeolite catalysts; 4) V, Fe, Cu based Heteropoly acid catalysts. Several of these are promising alternatives to the state-of the art industrial reference catalyst. All catalysts prepared in the present project exhibit higher to much higher alkali resistance compared to the commercial reference. Furthermore, two catalysts, i.e. 20 wt% V{sub 2}O-3-TiO{sub 2} nano-catalyst and the 4 wt% CuO-Mordenite zeolite based catalyst have also a higher initial SCR activity compared to the commercial one before alkali poisoning. Thus, those two catalysts might be attractive for SCR deNO{sub x} purposes even under ''normal'' fuel conditions in power plants and elsewhere making them strong candidates for further development. These efforts regarding all the promising catalysts will be pursued after this project has expired through a one year Proof of Concept project granted by the Danish Agency for Science, Technology and Innovation. Also the severe rate of deactivation due to alkali poisons can be avoided by coating the vanadium catalyst with Mg. Overall, the protective coating of SCR catalysts developed in the project seems promising and a patent application has been filed for this technology. Finally, a completely different approach to

  13. Electrical conduction and glass relaxation in alkali- silicate glasses

    Science.gov (United States)

    Angel, Paul William

    Electrical response measurements from 1 Hz to 1 MHz between 50o and 540oC were made on potassium, sodium and lithium-silicate glasses with low alkali oxide contents. Conductivity and electrical relaxation responses for both annealed and air quenched glasses of the same composition were compared. Quenching was found to lower the dc conductivity, σdc, and activation energy as well as increase the pre-exponential term when compared to the corresponding annealed glass of the same composition. All of the glasses exhibited Arrhenius behavior in the log σdc against 1/T plots. A sharp decrease in σdc was observed for glasses containing alkali concentrations of 7 mol% or less. The σdc activation energy exhibited similar behavior when plotted as a function of alkali composition and was explained in terms of a mixture of the weak and strong electrolyte models. The depression angle for fits to the complex impedance data were also measured as a function of thermal history, alkali concentration and alkali species. These results were interpreted in terms of changes in the distribution of relaxation times. Annealed samples from a single melt of a 10 mol% K2O-90SiO2 glass were reheated to temperatures ranging from 450o to 800oC, held isothermally for 20 min, and then quenched in either air or silicon oil. The complex impedance of both an annealed and the quenched samples were then measured as a function of temperature from 120o to 250oC. The σdc was found to be remain unaffected by heat treatments below 450oC, to increase rapidly over an approximate 200oC range of temperatures that was dependent on cooling rate and to be constant for heat treatments above this range. This behavior is interpreted in terms of the mean structural relaxation time as a function of temperature and cooling rate near the glass transition temperature and glass transformation ranges. A more detailed definition for the transition and transformation temperatures and ranges was also provided.

  14. Modifier interaction and mixed-alkali effect in bond constraint theory applied to ternary alkali metaphosphate glasses

    Directory of Open Access Journals (Sweden)

    Bruno ePoletto Rodrigues

    2016-05-01

    Full Text Available Introducing an interaction parameter γ, we implement modifier interaction and the mixed-alkali effect into bond constraint theory, and apply this extension for simplistic property prediction on ternary phosphate glasses. The severity of the mixed alkali effect results from the interplay of two simultaneous contributions: Bond constraints on the modifier species soften or stiffen with decreasing or increasing γ, respectively. When the modifier size is not too dissimilar the decrease in γ reflects that the alkali ions can easily migrate between different sites, forcing the network to continuously re-accommodate for any subsequent distortions. With increasing size difference, migration becomes increasingly difficult without considerable network deformation. This holds even for smaller ions, where the sluggish dynamics of the larger constituent result in blocking of the fast ion movement, leading to the subsequent increase in γ. Beyond a certain size difference in the modifier pair, a value of γ exceeding unity may indicate the presence of steric hindrance due to the large surrounding modifiers impeding the phosphate network to re-accommodate deformation.

  15. Structural analysis of alkali cations in mixed alkali silicate glasses by 23Na and 133Cs MAS NMR

    Directory of Open Access Journals (Sweden)

    T. Minami

    2014-12-01

    Full Text Available We report the structural analysis of Na+ and Cs+ in sodium cesium silicate glasses by using 23Na and 133Cs magic-angle spinning nuclear magnetic resonance (MAS NMR spectroscopy. In the NMR spectra of cesium silicate crystals, the peak position shifted to higher magnetic field for structures with larger Cs+ coordination numbers and to lower magnetic field for smaller Cs+ coordination numbers. The MAS NMR spectra of xNa2O-yCs2O-2SiO2 (x = 0, 0.2, 0.33, 0.5, 0.66, 0.8, 1.0; x + y = 1 glass reveal that the average coordination number of both the alkali cations decreases with increasing Cs+/(Na+ + Cs+ ratio. In addition, the coordination number of Na+ in xNa2O-yCs2O-2SiO2 glass is smaller than that of Cs+. This difference between the average coordination numbers of the alkali cations is considered to be one structural reason of the mixed alkali effect.

  16. Path integral Monte Carlo study of 4He clusters doped with alkali and alkali-earth ions.

    Science.gov (United States)

    Galli, D E; Ceperley, D M; Reatto, L

    2011-06-30

    Path integral Monte Carlo calculations of (4)He nanodroplets doped with alkali (Na(+), K(+) and Cs(+)) and alkali-earth (Be(+) and Mg(+)) ions are presented. We study the system at T = 1 K and between 14 and 128 (4)He atoms. For all studied systems, we find that the ion is well localized at the center of the droplet with the formation of a "snowball" of well-defined shells of localized (4)He atoms forming solid-like order in at least the first surrounding shell. The number of surrounding helium shells (two or three) and the number of atoms per shell and the degree of localization of the helium atoms are sensitive to the type of ion. The number of (4)He atoms in the first shell varies from 12 for Na(+) to 18 for Mg(+) and depends weakly on the size of the droplet. The study of the density profile and of the angular correlations shows that the local solid-like order is more pronounced for the alkali ions with Na(+) giving a very stable icosahedral order extending up to three shells.

  17. Pretreatment of garden biomass by alkali-assisted ultrasonication: effects on enzymatic hydrolysis and ultrastructural changes.

    Science.gov (United States)

    Gabhane, Jagdish; William, Spm Prince; Vaidya, Atul Narayan; Anand, Duraisamy; Wate, Satish

    2014-01-01

    The present investigation aims at studying the effectiveness of alkali-assisted ultrasonication on pretreatment of garden biomass (GB). Dry and powdered GB suspended in 1% NaOH was ultrasonicated for 15, 30 and 60 minutes at a frequency of 25 KHZ. The mode of action and effectiveness of alkali-assisted ultrasonication on GB was established through microscopic, scanning electron microscopic and X-ray diffraction studies. A perusal of results showed that alkali-assisted ultrasonication led to fibrillation of GB which ultimately facilitated enzymatic hydrolysis. The results also indicated that alkali-assisted ultrasonication is an efficient means of pretreatment of GB at moderate (45-50°C) working temperature and low (1%) concentration of alkali. The yield of reducing sugar after enzymatic hydrolysis increased almost six times as compared to control due to alkali-assisted ultrasonication.

  18. Synthesis and Characterization of 5- and 6- Coordinated Alkali Pertechnetates

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, Jamie; Soderquist, Chuck; Gassman, Paul; Walter, Eric; Lukens, Wayne; McCloy, John S.

    2017-01-01

    The local chemistry of technetium-99 (99Tc) in oxide glasses is important for understanding the incorporation and long-term release of Tc from nuclear waste glasses, both those for legacy defense wastes and fuel reprocessing wastes. Tc preferably forms Tc(VII), Tc(IV), or Tc(0) in glass, depending on the level of reduction of the melt. Tc(VII) in oxide glasses is normally assumed to be isolated pertechnetate TcO4-anions surrounded by alkali, but can occasionally precipitate as alkali pertechnetate salts such as KTcO4and NaTcO4when Tc concentration is high. In these cases, Tc(VII) is 4-coordinated by oxygen. A reinvestigation of the chemistry of alkali-technetium-oxides formed under oxidizing conditions and at temperatures used to prepare nuclear waste glasses showed that higher coordinated alkali Tc(VII) oxide species had been reported, including those with the TcO5-and TcO6-anions. The chemistry of alkali Tc(VII) and other alkali-Tc-oxides is reviewed, along with relevant synthesis conditions.

    Additionally, we report attempts to make 5- and 6-coordinate pertechnetate compounds of K, Na, and Li, i.e. TcO5-and TcO6-. It was found that higher coordinated species are very sensitive to water, and easily decompose into their respective pertechnetates. It was difficult to obtain pure compounds, but mixtures of the pertechnetate and other phase(s) were frequently found, as evidenced by x-ray absorption spectroscopy (XAS), neutron diffraction (ND), and Raman spectroscopy. Low temperature electron paramagnetic resonance (EPR) measurements showed the possibility of Tc(IV) and Tc(VI) in Na3TcO5and Na5TcO6compounds.

    It was hypothesized that the smaller counter cation would result in more stable pertechnetates. To confirm the synthesis method, LiReO4and Li5

  19. Anti-inflammatory agents’ effect on esophageal alkali burn: An experimental study

    Directory of Open Access Journals (Sweden)

    Semih Koçyiğit

    2015-09-01

    Full Text Available Objective: Corrosive burns of the esophagus are some reports demonstrating that the stricture ratio exceeds 50% in the case of a severe burn. In this experimental animal study of rats, we aimed to investigate the effects of the anti-inflammatory agents in esophageal alkali burns. Methods: Twenty-eight Wistar albino rats, weighing from 220 to 250 gr, were used in the study. And following a starving period of 12 hours, we provided general anesthesia with intramuscular ketamin HCL (90 mg/kg and xylazine (10mg/kg. A corrosive burn just like the corrosive esophagitis was done under general anesthesia. The rats were divided into four groups (7 rats for each. The intraluminal area of 1cm in the esophagus of the rats of the first group was washed using serum physiologic (1 ml. Group II received parenteral antibiotic treatment. Group III received antibiotic and dexamethasone regiment, while the Group IV received antibiotic and prednisolone. Each animal was sacrificed on the 21st day, and their abdominal esophagus was resected for histopathological investigation. The submucosal increase in the collagen, damage to the muscularis mucosa and to the tunica muscularis were three parameters demonstrating the injury histopathologically. Results: There was no injury in the Group I. There was injury in each parameter in the Group II, III, and IV compared with Group I. In the comparison between Group II and III, there was less injury in the Group III. In comparison with Group II there was also significant injury in the muscularis mucosa and the tunica muscularis in the Group I (p<0.05. Conclusion: Prednisolone may decrease the new collagen synthesis that progresses up to muscularis mucosa, but the effect on the lowering the stricture formation is not better than dexamethasone.

  20. Decay curve analysis of alkali-silicate glass exposed to electrons

    CERN Document Server

    Gedeon, O

    2002-01-01

    Binary and ternary potassium, rubidium and caesium glasses were irradiated by an electron beam with energy varying from 10 to 50 keV. Alkali ion x-ray decays were recorded and afterward incubation periods were determined. The incubation period versus electron energy curves revealed thresholds, which are typical for each alkali species. The threshold ratios are proportional to the mass of the alkali species, consistent with the suggested elastic scattering assisted hopping mechanism. (author)

  1. Calculation of Radiative Corrections to E1 matrix elements in the Neutral Alkalis

    Energy Technology Data Exchange (ETDEWEB)

    Sapirstein, J; Cheng, K T

    2004-09-28

    Radiative corrections to E1 matrix elements for ns-np transitions in the alkali metal atoms lithium through francium are evaluated. They are found to be small for the lighter alkalis but significantly larger for the heavier alkalis, and in the case of cesium much larger than the experimental accuracy. The relation of the matrix element calculation to a recent decay rate calculation for hydrogenic ions is discussed, and application of the method to parity nonconservation in cesium is described.

  2. Characterization of the extent of Mercury Contamination in the Androscoggin River from a former Chlor-alkali Facility, Berlin, New Hampshire

    Science.gov (United States)

    Chalmers, A.; Marvin-Dipasquale, M. C.; Rosiu, C.; Luce, D.; Coles, J.; Zimmerman, M.; Smith, T.

    2010-12-01

    From the late 1800s to the 1960s a chlor-alkali plant was used to produce chlorine gas for the papermaking industry in Berlin, New Hampshire. During operation of the chlor-alkali facility, elemental mercury (Hg) was released to the environment, contaminating soils and the underlying fractured rock. Investigations have revealed that elemental Hg continues to seep through bedrock fractures into the adjacent Androscoggin River. This study evaluates the extent and transformation of Hg contamination in the Androscoggin River by comparing a reference site 17 kilometers above the former chlor-alkali facility to 5 sites ranging from 1 to 16 km downstream from the facility. Total and methyl Hg (THg and MeHg, respectively), among other analytes, were characterized in surface water, pore water, sediment and biological tissue samples at each site. Bed sediment was also assessed for bio-available (tin-reducible) inorganic Hg (II) and microbial MeHg production potential rates. Acid extractable ferrous iron, crystalline and amorphous (poorly crystalline) ferric iron, total reduced sulfur, particle size, and organic content in bed sediment was analyzed to help explain spatial differences in MeHg production rates and bio-available Hg (II) among sites. The information provided by this study will help evaluate the extent of Hg contamination in the Androscoggin River, will improve our understanding of the controls on MeHg production in the Androscoggin River system, and will be used by the U.S. Environmental Protection Agency to support remediation of the chlor-alkali facility site.

  3. Alkali-Silica Reaction Inhibited by LiOH and Its Mechanism

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A high alkali reactive aggregate-zeolitization perlite was used to test the long-term effectiveness of LiOH in inhibiting alkali-silica reaction.In this paper,the rigorous conditions were designed that the mortar bars had been cured at 80℃ for 3 years after autoclaved 24 hours at 150℃.Under this condition,LiOH was able to inhibit the alkali-silica reaction long-term effectiveness.Not only the relationship between the molar ratio of n(Li)/(Na) and the alkali contents in systems was established, but also the governing mechanism of such effects was also studied by SEM.

  4. Exotic s-wave superconductivity in alkali-doped fullerides.

    Science.gov (United States)

    Nomura, Yusuke; Sakai, Shiro; Capone, Massimo; Arita, Ryotaro

    2016-04-20

    Alkali-doped fullerides (A3C60 with A = K, Rb, Cs) show a surprising phase diagram, in which a high transition-temperature (Tc) s-wave superconducting state emerges next to a Mott insulating phase as a function of the lattice spacing. This is in contrast with the common belief that Mott physics and phonon-driven s-wave superconductivity are incompatible, raising a fundamental question on the mechanism of the high-Tc superconductivity. This article reviews recent ab initio calculations, which have succeeded in reproducing comprehensively the experimental phase diagram with high accuracy and elucidated an unusual cooperation between the electron-phonon coupling and the electron-electron interactions leading to Mott localization to realize an unconventional s-wave superconductivity in the alkali-doped fullerides. A driving force behind the exotic physics is unusual intramolecular interactions, characterized by the coexistence of a strongly repulsive Coulomb interaction and a small effectively negative exchange interaction. This is realized by a subtle energy balance between the coupling with the Jahn-Teller phonons and Hund's coupling within the C60 molecule. The unusual form of the interaction leads to a formation of pairs of up- and down-spin electrons on the molecules, which enables the s-wave pairing. The emergent superconductivity crucially relies on the presence of the Jahn-Teller phonons, but surprisingly benefits from the strong correlations because the correlations suppress the kinetic energy of the electrons and help the formation of the electron pairs, in agreement with previous model calculations. This confirms that the alkali-doped fullerides are a new type of unconventional superconductors, where the unusual synergy between the phonons and Coulomb interactions drives the high-Tc superconductivity.

  5. Interaction of alkali and alkaline earth ions with Ochratoxin A

    Energy Technology Data Exchange (ETDEWEB)

    Poor, Miklos [Institute of Laboratory Medicine, University of Pecs, Pecs H-7624 (Hungary); Kunsagi-Mate, Sandor; Matisz, Gergely; Li, Yin; Czibulya, Zsuzsanna [Department of General and Physical Chemistry, University of Pecs, Pecs H-7624 (Hungary); Janos Szentagothai Research Center, Pecs H-7624 (Hungary); Peles-Lemli, Beata [Department of General and Physical Chemistry, University of Pecs, Pecs H-7624 (Hungary); Koszegi, Tamas, E-mail: koszegit@freemail.hu [Institute of Laboratory Medicine, University of Pecs, Pecs H-7624 (Hungary)

    2013-03-15

    The effect of alkali and alkaline earth ions on the chemical equilibrium of mono- and dianionic forms of the mycotoxin Ochratoxin A (OTA) and their bonding onto the surface of Bovine Serum Albumin (BSA) have been investigated by fluorescence spectroscopy and fluorescence polarization techniques. Our results show that alkali metal ions shift the chemical equilibrium towards formation of dianionic form of OTA. Furthermore, the alkaline earth ions can compete with BSA for binding to OTA when these ions are present in millimolar concentrations. Our data also highlight the possibility that the 'free' fraction of OTA (not bound onto the surface of albumin) or at least a part of it is present in cation-bound form in body fluids. These observations are supported by stability constants and quantum-chemical calculations. Among the studied alkaline metal ions magnesium showed the highest affinity towards OTA under physiological conditions. Further research is required to analyze the potential significance of Mg{sup 2+}-OTA complex in cellular uptake and/or elimination of the toxin in the human body. - Highlights: Black-Right-Pointing-Pointer Fluorescence spectroscopy reveals cation-Ochratoxin A (OTA) interactions. Black-Right-Pointing-Pointer Alkali ions shift the equilibrium of OTA to formation of a dianionic structure. Black-Right-Pointing-Pointer Alkaline earth ions directly bind to OTA in the order: Mg{sup 2+}, Ca{sup 2+}, Ba{sup 2+}. Black-Right-Pointing-Pointer Quantum chemical calculations and logK values support our experimental data.

  6. Exotic s-wave superconductivity in alkali-doped fullerides

    Science.gov (United States)

    Nomura, Yusuke; Sakai, Shiro; Capone, Massimo; Arita, Ryotaro

    2016-04-01

    Alkali-doped fullerides ({{A}3}{{\\text{C}}60} with A  =  K, Rb, Cs) show a surprising phase diagram, in which a high transition-temperature ({{T}\\text{c}} ) s-wave superconducting state emerges next to a Mott insulating phase as a function of the lattice spacing. This is in contrast with the common belief that Mott physics and phonon-driven s-wave superconductivity are incompatible, raising a fundamental question on the mechanism of the high-{{T}\\text{c}} superconductivity. This article reviews recent ab initio calculations, which have succeeded in reproducing comprehensively the experimental phase diagram with high accuracy and elucidated an unusual cooperation between the electron-phonon coupling and the electron-electron interactions leading to Mott localization to realize an unconventional s-wave superconductivity in the alkali-doped fullerides. A driving force behind the exotic physics is unusual intramolecular interactions, characterized by the coexistence of a strongly repulsive Coulomb interaction and a small effectively negative exchange interaction. This is realized by a subtle energy balance between the coupling with the Jahn-Teller phonons and Hund’s coupling within the {{\\text{C}}60} molecule. The unusual form of the interaction leads to a formation of pairs of up- and down-spin electrons on the molecules, which enables the s-wave pairing. The emergent superconductivity crucially relies on the presence of the Jahn-Teller phonons, but surprisingly benefits from the strong correlations because the correlations suppress the kinetic energy of the electrons and help the formation of the electron pairs, in agreement with previous model calculations. This confirms that the alkali-doped fullerides are a new type of unconventional superconductors, where the unusual synergy between the phonons and Coulomb interactions drives the high-{{T}\\text{c}} superconductivity.

  7. Theoretical determination of the alkali-metal superoxide bond energies

    Science.gov (United States)

    Partridge, Harry; Bauschlicher, Charles W., Jr.; Sodupe, Mariona; Langhoff, Stephen R.

    1992-01-01

    The bond dissociation energies for the alkali-metal superoxides have been computed using extensive Gaussian basis sets and treating electron correlation at the modified coupled-pair functional level. Our computed D0 values are 61.4, 37.2, 40.6, and 38.4 kcal/mol for LiO2, NaO2, KO2, and RbO2, respectively. These values, which are expected to be lower bounds and accurate to 2 kcal/mol, agree well with some of the older flame data, but rule out several recent experimental measurements.

  8. Wave optics simulation of diode pumped alkali laser (DPAL)

    Science.gov (United States)

    Endo, Masamori; Nagaoka, Ryuji; Nagaoka, Hiroki; Nagai, Toru; Wani, Fumio

    2016-03-01

    A numerical simulation code for a diode pumped alkali laser (DPAL) was developed. The code employs the Fresnel- Kirchhoff diffraction integral for both laser mode and pump light propagations. A three-dimensional rate equation set was developed to determine the local gain. The spectral divergence of the pump beam was represented by a series of monochromatic beams with different wavelengths. The calculated results showed an excellent agreements with relevant experimental results. It was found that the main channel of the pump power drain is the spontaneous emission from the upper level of the lasing transition.

  9. Chemical compatibility of structural materials in alkali metals

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Rink, D.L.; Haglund, R. [Argonne National Lab., Chicago, IL (United States)] [and others

    1995-04-01

    The objectives of this task are to (a) evaluate the chemical compatibility of structural alloys such as V-5 wt.%Cr-5 wt.%Ti alloy and Type 316 stainless steel for application in liquid alkali metals such as lithium and sodium-78 wt.% potassium (NaK) at temperatures in the range that are of interest for International Thermonuclear Experimental Reactor (ITER); (b) evaluate the transfer of nonmetallic elements such as oxygen, nitrogen, carbon, and hydrogen between structural materials and liquid metals; and (c) evaluate the effects of such transfers on the mechanical and microstructural characteristics of the materials for long-term service in liquid-metal-environments.

  10. Alkali-silica reaction resistant concrete using pumice blended cement

    Science.gov (United States)

    Ramasamy, Uma

    Durability of structures is a major challenge for the building industry. One of the many types of concrete deterioration that can affect durability is alkali-silica reaction (ASR). ASR has been found in most types of concrete structures, including dams, bridges, pavements, and other structures that are 20 to 50 years old. The degradation mechanism of ASR produces a gel that significantly expands in the presence of water as supplied from the surrounding environment. This expansion gel product can create high stresses and cracking of the concrete, which can lead to other forms of degradation and expensive structural replacement costs. The four essential factors that produce an expansive ASR gel in concrete are the presence of alkalis, siliceous aggregate, moisture, and free calcium hydroxide (CH). If concrete is starved of any one of these essential components, the expansion can be prevented. Reducing CH through the use of a supplementary cementitious material (SCM) such as natural pozzolan pumice is the focus of this research. By using a pozzolan, the amount of CH is reduced with time based on the effectiveness of the pozzolan. Many pozzolans exist, but one such naturally occurring pozzolanic material is pumice. This research focuses on determining the effect of a finely ground pumice as a SCM in terms of its resistance to ASR expansion, as well as improving resistance to other potential concrete durability mechanisms. In spite of having high alkali contents in the pumice, mixtures containing the SCM pumice more effectively mitigated the ASR expansion reaction than other degradation mechanisms. Depending on the reactivity of the aggregates and fineness of the pumice, 10-15% replacement of cement with the pumice was found to reduce the ASR expansion to the acceptable limits. The amount of CH remaining in the concrete was compared to the ASR expansion in order to improve understanding of the role of CH in the ASR reaction. Thermo-gravimetric analysis (TGA) and X

  11. Surface phonons on Al(111) surface covered by alkali metals

    Science.gov (United States)

    Rusina, G. G.; Eremeev, S. V.; Borisova, S. D.; Sklyadneva, I. Yu.; Chulkov, E. V.

    2005-06-01

    We investigated the vibrational and structural properties of the Al(111)-(3×3)R30°-AM (AM=Na,K,Li) adsorbed systems using interaction potentials from the embedded-atom method. The surface relaxation, surface phonon dispersion, and polarization of vibrational modes for the alkali adatoms and the substrate atoms as well as the local density of states are discussed. Our calculated structural parameters are in close agreement with experimental and ab initio results. The obtained vibrational frequencies compare fairly well with the available experimental data.

  12. Electrochemical synthesis of alkali-intercalated iron selenide superconductors

    Institute of Scientific and Technical Information of China (English)

    申士杰; 应天平; 王刚; 金士锋; 张韩; 林志萍; 陈小龙

    2015-01-01

    Electrochemical method has been used to insert K/Na into FeSe lattice to prepare alkali-intercalated iron selenides at room temperature. Magnetization measurement reveals that KxFe2Se2 and NaxFe2Se2 are superconductive at 31 K and 46 K, respectively. This is the first successful report of obtaining metal-intercalated FeSe-based high-temperature superconductors using electrochemical method. It provides an effective route to synthesize metal-intercalated layered compounds for new superconductor exploration.

  13. Hypercalcemic encephalopathy due to milk alkali syndrome and injection teriparatide

    Directory of Open Access Journals (Sweden)

    Sandeep Kharb

    2012-01-01

    Full Text Available An 82-year-old male, a known case of severe osteoporosis with vertebral fracture and prostatic carcinoma, was treated with gonadotropin releasing hormone analogue, calcium carbonate, cholecalciferol sachet and injection teriparatide. His diet consisted of milk and curd. He developed altered behavior and generalized weakness, and on investigation, hypercalcemia, hypokalemia, and metabolic alkalosis with low parathyroid hormone levels were detected. Injection teriparatide was stopped and he was managed with forced saline diuresis and injection zoledronic acid. He was diagnosed as a case of milk alkali syndrome in whom teriparatide and prolonged immobilization played a permissive role in the development of hypercalcemic encephalopathy.

  14. Analysis and modeling of alkali halide aqueous solutions

    DEFF Research Database (Denmark)

    Kim, Sun Hyung; Anantpinijwatna, Amata; Kang, Jeong Won;

    2016-01-01

    A new model is proposed for correlation and prediction of thermodynamic properties of electrolyte solutions. In the proposed model, terms of a second virial coefficient-type and of a KT-UNIFAC model are used to account for a contribution of binary interactions between ion and ion, and water and ion...... on calculations for various electrolyte properties of alkali halide aqueous solutions such as mean ionic activity coefficients, osmotic coefficients, and salt solubilities. The model covers highly nonideal electrolyte systems such as lithium chloride, lithium bromide and lithium iodide, that is, systems...

  15. Precision two-photon spectroscopy of alkali elements

    Indian Academy of Sciences (India)

    P V Kiran Kumar; M V Suryanarayana

    2014-08-01

    In this paper, we have briefly reviewed the work on two-photon spectroscopy of alkali elements and its applications. The technique of Doppler-free two-photon spectroscopy is briefly summarized. A review of various techniques adopted for measuring absolute frequencies of the atomic transitions and precision measurements of isotope shifts and hyperfine structures (HFS) is presented. Some of the recent works on precision measurements of HFS constants of 6 ${}^2S_{1/2}$ level of ${}^{39}$K and ${}^{41}$K, 9 ${}^2S_{1/2}$ level and 7 ${}^2D_{3/2}$ level of 133Cs are also discussed.

  16. Rate Modelling of Alkali Gelatinization at Low Conversions

    Directory of Open Access Journals (Sweden)

    Osoka Emmanuel CHIBUIKE

    2010-12-01

    Full Text Available The rate of starch gelatinisation under strong alkali conditions was modeled at low conversion (x < 0.4, with the degree of gelatinisation (conversion defined in terms of sample viscosity. Experimental data at low conversion were fit to eleven rate models based on the mechanism of the unreacted-core model and the rate controlling steps determined. Film diffusion (stokes regime plus Product layer diffusion steps control the rate of reaction for all sodium hydroxide concentrations and at low conversion (x < 0.4, with the dominance shifting from Film diffusion to Product layer diffusion as sodium hydroxide concentration is increased.

  17. Magnesia Modification of Alkali-Activated Slag Fly Ash Cement

    Institute of Scientific and Technical Information of China (English)

    SHEN Weiguo; WANG Yiheng; ZHANG Tao; ZHOU Mingkai; LI Jiasheng; CUI Xiaoyu

    2011-01-01

    A new type of magnesia modification alkali-activated cement was prepared, the strength, setting time, shrinkage ratio and cracking behavior, as well as the composition and structure of the hydration product were investigated. The results indicate that the setting time of this cement is similar to that of the ordinary commercial cements; its strength reaches the standard of 42.5 degree cement, its cracking resistance has been remarkably improved because of the micro-aggregate effect of fly ash and shrinkage compensating of magnesia.

  18. Integrated oil production and upgrading using molten alkali metal

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  19. Integrated oil production and upgrading using molten alkali metal

    Science.gov (United States)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  20. Fabrication method for microscopic vapor cells for alkali atoms.

    Science.gov (United States)

    Baluktsian, T; Urban, C; Bublat, T; Giessen, H; Löw, R; Pfau, T

    2010-06-15

    A quantum network that consists of several components should ideally work on a single physical platform. Neutral alkali atoms have the potential to be very well suited for this purpose due to their electronic structure, which involves long-lived nuclear spins and very sensitive highly excited Rydberg states. In this Letter, we describe a fabrication method based on quartz glass to structure arbitrary shapes of microscopic vapor cells. We show that the usual spectroscopic properties known from macroscopic vapor cells are almost unaffected by the strong confinement.

  1. Electric dipole polarizabilities of Rydberg states of alkali atoms

    CERN Document Server

    Yerokhin, V A; Fritzsche, S; Surzhykov, A

    2016-01-01

    Calculations of the static electric-dipole scalar and tensor polarizabilities are presented for two alkali atoms, Rb and Cs, for the $nS$, $nP_{1/2, 3/2}$, and $nD_{3/2, 5/2}$ states with large principal quantum numbers up to $n = 50$. The calculations are performed within an effective one-electron approximation, based on the Dirac-Fock Hamiltonian with a semi-empirical core-polarization potential. The obtained results are compared with those from a simpler semi-empirical approach and with available experimental data.

  2. Food composition and acid-base balance: alimentary alkali depletion and acid load in herbivores.

    Science.gov (United States)

    Kiwull-Schöne, Heidrun; Kiwull, Peter; Manz, Friedrich; Kalhoff, Hermann

    2008-02-01

    Alkali-enriched diets are recommended for humans to diminish the net acid load of their usual diet. In contrast, herbivores have to deal with a high dietary alkali impact on acid-base balance. Here we explore the role of nutritional alkali in experimentally induced chronic metabolic acidosis. Data were collected from healthy male adult rabbits kept in metabolism cages to obtain 24-h urine and arterial blood samples. Randomized groups consumed rabbit diets ad libitum, providing sufficient energy but variable alkali load. One subgroup (n = 10) received high-alkali food and approximately 15 mEq/kg ammonium chloride (NH4Cl) with its drinking water for 5 d. Another group (n = 14) was fed low-alkali food for 5 d and given approximately 4 mEq/kg NH4Cl daily for the last 2 d. The wide range of alimentary acid-base load was significantly reflected by renal base excretion, but normal acid-base conditions were maintained in the arterial blood. In rabbits fed a high-alkali diet, the excreted alkaline urine (pH(u) > 8.0) typically contained a large amount of precipitated carbonate, whereas in rabbits fed a low-alkali diet, both pH(u) and precipitate decreased considerably. During high-alkali feeding, application of NH4Cl likewise decreased pH(u), but arterial pH was still maintained with no indication of metabolic acidosis. During low-alkali feeding, a comparably small amount of added NH4Cl further lowered pH(u) and was accompanied by a significant systemic metabolic acidosis. We conclude that exhausted renal base-saving function by dietary alkali depletion is a prerequisite for growing susceptibility to NH4Cl-induced chronic metabolic acidosis in the herbivore rabbit.

  3. Detoxification and safety evaluation of aflatoxin B1 in peanut oil using alkali refining.

    Science.gov (United States)

    Ji, Ning; Diao, Enjie; Li, Xiangyang; Zhang, Zheng; Dong, Haizhou

    2016-09-01

    Aflatoxin B1 (AFB1 ) is often detected in peanut oil, which comes from contaminated peanuts. AFB1 in peanut oil seriously threatens the health of consumers. However, there are few methods to effectively remove AFB1 in peanut oil. This study aimed to use an alkali-refining method to degrade AFB1 in peanut oil efficiently without increasing the equipment of oil and fat refining. The optimum detoxifying conditions of AFB1 in peanut oil with alkali refining were established using response surface methodology (RSM), and the safety of peanut oil after being refined with alkali was evaluated based on the Ames tests and HepG2 cell viability. The results showed that AFB1 in peanut oil was decreased from 34.78 to 0.37 µg kg(-1) (98.94% reduction) under the optimum detoxifying conditions, i.e. when the initial temperature of alkali refining was 43.51 °C, the amount of excess alkali was 0.30%, the content of alkali solution was 23.42% and the end temperature of alkali refining was 77.07 °C. The acid value and color of peanut oil refined by alkali were improved significantly, while the peroxide value was increased within an acceptable level. The safety of peanut oil contaminated by AFB1 was improved significantly after being refined with alkali. These results indicate that alkali refining is an effective method for removing AFB1 in peanut oil. The optimum detoxifying conditions of AFB1 in peanut oil with alkali refining could be used to guide the production of oil companies for ensuring food safety. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

  4. Effects of Heavy Metals and Saline-alkali on Growth, Physiology and Biochemistry of Orychophragmus violaceus

    Institute of Scientific and Technical Information of China (English)

    Xiaoai ZHANG; Zhihui WANG; Xinquan ZHANG; Mingyang Ll; Jing ZUO

    2012-01-01

    Abstract [Oh.jective] The aim was to study on effects of heavy metals and saline-al- kali on growth, physiology and biochemistry of Orychophragmus violaceus. [Method] Taken Orychophragmus violaceus as materials, growth, physiology and biochemistry were explored under stress of saline-alkali and heavy metals (light, moderate and se- vere saline-alkali, Pb, Pb + Cd, light saline-alkali + Pb, moderate saline-alkali + Pb, severe saline-alkali + Pb, light saline-alkali + Pb + Cd, moderate saline-alkali + Pb + Cd and severe saline-alkali + Pb + Cd) with control group set. [Result] Light stress of saline-alkali had little effect on membrane permeability, as follows: MDA contents in leaves and root systems declined by 25.6% and 9.0% compared with control group; Pb (500 mg/L) stress promoted synthetization of photosynthetic pigments, as follows: chlorophyll a and b and carotenoid increased by 0.86%, 0.69% and 6.25% than those of control group; combined stresses of Pb and Cd destroyed synthetization of photosynthetic pigments, among which carotenoid was more sensitive; under com- bined stresses of saline-alkali, Pb and Cd, POD and SOD activities, soluble saccha- rides and Pro content all increased and activities of POD and SOD in root system were both higher than those in leaves. [Conclusion] Orychophragmus violaceus is with resistance against light combined stresses of saline-alkali and Pb (500 mg/L).

  5. Dispersion coefficients for the interaction of inert gas atoms with alkali and alkaline earth ions and alkali atoms with their singly ionized ions

    CERN Document Server

    Singh, Sukhjit; Sahoo, B K; Arora, Bindiya

    2016-01-01

    We report the dispersion coefficients for the interacting inert gas atoms with the alkali ions, alkaline earth ions and alkali atoms with their singly charged ions. We use our relativistic coupled-cluster method to determine dynamic dipole and quadrupole polarizabilities of the alkali atoms and singly ionized alkaline earth atoms, whereas a relativistic random phase approximation approach has been adopted to evaluate these quantities for the closed-shell configured inert gas atoms and the singly and doubly ionized alkali and alkaline earth atoms, respectively. Accuracies of these results are adjudged from the comparison of their static polarizability values with their respective experimental results. These polarizabilities are further compared with the other theoretical results. Reason for the improvement in the accuracies of our estimated dispersion coefficients than the data listed in [At. Data and Nucl. Data Tables 101, 58 (2015)] are discussed. Results for some of the atom-ion interacting systems were not...

  6. Alkali chloride induced corrosion of superheaters under biomass firing conditions: Improved insights from laboratory scale studies

    DEFF Research Database (Denmark)

    Okoro, Sunday Chukwudi; Montgomery, Melanie; Jappe Frandsen, Flemming

    2015-01-01

    to the formation of corrosive deposits (rich in alkali chlorides) on the surfaces of the superheaters. Accordingly, an extensive number of fundamental investigations have been undertaken to understand the basic mechanisms behind the alkali chloride induced high temperature corrosion of superheaters (for example...

  7. Effect of the Composite of Natural Zeolite and Fly Ash on Alkali-Silica Reaction

    Institute of Scientific and Technical Information of China (English)

    FENG Xiao-xin; FENG Nai-qian; HAN Dong

    2003-01-01

    The effect of the composite of natural zeolite and fly ash on alkali-silica reaction ( ASR ) was studied with natural alkali-reactive aggregate and quartz glass aggregate respecthvely. The expansive experiment of mortar bar and concrete prism was completed. The results show that ASR can be suppressed effectively by the composite of natural zeolite and fly ash.

  8. The Effects of Biochar on Germination and Growth of Wheat in Different Saline-alkali Soil

    Institute of Scientific and Technical Information of China (English)

    Guijun; WANG; Zhenwen; XU

    2013-01-01

    Saline alkali soil can cause physiological drought on crops,so only some salinity tolerant crops can grow in saline alkali soil.Biochar can increase the utilize efficiency of nutrient and the water retention of the soil,and affect the growth of the plant.In this research,four different proportion of biochar was added in five different levels of saline-alkali soil for pot culture experiment.The pH of the soil increases as the proportion of biochar increase in same saline-alkali level soil,while the EC decrease as the proportion of biochar increase.The germination rate of wheat seeds varies as the different of soil’s saline-alkali level.Notable among these results is the germination of wheat seeds in the serious saline-alkali soil without biochar added is 0,while in 45%biochar added in serious saline-alkali soil,the germination rate get to as high as 48.9%.Also,biochar improve the growth of wheat seedling,while for mild saline alkali soil and normal soil.Biochar had no obvious effect on the growth of wheat seedling.

  9. Structural Investigation of Alkali Activated Clay Minerals for Application in Water Treatment Systems

    Science.gov (United States)

    Bumanis, G.; Bajare, D.; Dembovska, L.

    2015-11-01

    Alkali activation technology can be applied for a wide range of alumo-silicates to produce innovative materials with various areas of application. Most researches focuse on the application of alumo-silicate materials in building industry as cement binder replacement to produce mortar and concrete [1]. However, alkali activation technology offers high potential also in biotechnologies [2]. In the processes where certain pH level, especially alkaline environment, must be ensured, alkali activated materials can be applied. One of such fields is water treatment systems where high level pH (up to pH 10.5) ensures efficient removal of water pollutants such as manganese [3]. Previous investigations had shown that alkali activation technology can be applied to calcined clay powder and aluminium scrap recycling waste as a foam forming agent to create porous alkali activated materials. This investigation focuses on the structural investigation of calcined kaolin and illite clay alkali activation processes. Chemical and mineralogical composition of both clays were determined and structural investigation of alkali activated materials was made by using XRD, DTA, FTIR analysis; the microstructure of hardened specimens was observed by SEM. Physical properties of the obtained material were determined. Investigation indicates the essential role of chemical composition of the clay used in the alkali activation process, and potential use of the obtained material in water treatment systems.

  10. Hydration number of alkali metal ions determined by insertion in a conducting polymer

    DEFF Research Database (Denmark)

    Skaarup, Steen

    2008-01-01

    . The solvation of alkali metal ions has been discussed for many years without a clear consensus. This work presents a systematic study of the hydration numbers of the 5 alkali metal ions, using the electrochemical insertion of the ions in a conducting polymer (polypyrrole containing the large immobile anion DBS...

  11. In situ alkali-silica reaction observed by x-ray microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kurtis, K.E.; Monteiro, P.J.M. [Univ. of California, Berkeley, CA (United States); Brown, J.T.; Meyer-Ilse, W. [Ernest Orlando Lawrence Berkeley National Lab., CA (United States)

    1997-04-01

    In concrete, alkali metal ions and hydroxyl ions contributed by the cement and reactive silicates present in aggregate can participate in a destructive alkali-silica reaction (ASR). This reaction of the alkalis with the silicates produces a gel that tends to imbibe water found in the concrete pores, leading to swelling of the gel and eventual cracking of the affected concrete member. Over 104 cases of alkali-aggregate reaction in dams and spillways have been reported around the world. At present, no method exists to arrest the expansive chemical reaction which generates significant distress in the affected structures. Most existing techniques available for the examination of concrete microstructure, including ASR products, demand that samples be dried and exposed to high pressure during the observation period. These sample preparation requirements present a major disadvantage for the study of alkali-silica reaction. Given the nature of the reaction and the affect of water on its products, it is likely that the removal of water will affect the morphology, creating artifacts in the sample. The purpose of this research is to observe and characterize the alkali-silica reaction, including each of the specific reactions identified previously, in situ without introducing sample artifacts. For observation of unconditioned samples, x-ray microscopy offers an opportunity for such an examination of the alkali-silica reaction. Currently, this investigation is focusing on the effect of calcium ions on the alkali-silica reaction.

  12. Provenance of sands from the confluence of the Amazon and Madeira rivers based on detrital heavy minerals and luminescence of quartz and feldspar

    Science.gov (United States)

    do Nascimento, Daniel R.; Sawakuchi, André O.; Guedes, Carlos C. F.; Giannini, Paulo C. F.; Grohmann, Carlos H.; Ferreira, Manuela P.

    2015-03-01

    Source-to-sink systems are poorly known in tropical rivers. For the Amazonian rivers, the majority of the provenance studies remain focused on the suspended load, implying a poor understanding of the processes governing production and distribution of sands. In this study, we perform heavy mineral and optically stimulated luminescence (OSL) analysis to cover the entire spectrum (heavy and light minerals fraction) of 29 sand samples of the Lower Madeira river region (Amazon and Madeira rivers), of which the main goal was to find provenance indicators specific to these rivers. Despite the tropical humid climate, the sands of the Amazon and Lower Madeira rivers are rich in unstable heavy minerals as augite, hypersthene, green hornblende and andalusite. The Madeira river is highlighted by its higher content of andalusite, with source attributed to the Amazon Craton (medium-to-high grade metamorphic rocks), while the Amazon river, upstream of the Madeira river mouth, has a signature of augite and hypersthene, that suggests an Andean provenance (volcanic rocks). Sands from the Madeira river can be tracked in the Amazon river by the increasing concentration in andalusite. OSL analysis of the light minerals fraction was used as an index of feldspar concentration and sedimentary history of quartz grains. Lower feldspar concentration and quartz grains with longer sedimentary history (higher OSL sensitivity) also point to a major contribution of cratonic sources for the sands in the Madeira river. While the sands from the Lower Madeira would be mainly supplied by cratonic rocks, previous work recognised that suspended sediments (silt and clay) are derived from Andean rocks. Therefore, we interpret a decoupling between the sources of sand and mud (silt and clay) under transport in the Madeira river. Andean sands (rich in augite and hypersthene) would be trapped in the foreland zones of the Beni and Mamoré tributaries. In the Amazon river sands, the low OSL sensitivity of the

  13. Mineral dissolution in the Cape Cod aquifer, Massachusetts, USA: I . Reaction stoichiometry and impact of accessory feldspar and glauconite on strontium isotopes, solute concentrations, and REY distribution

    Science.gov (United States)

    Bau, Michael; Alexander, Brian; Chesley, John T.; Dulski, Peter; Brantley, Susan L.

    2004-03-01

    To compare relative reaction rates of mineral dissolution in a mineralogically simple groundwater aquifer, we studied the controls on solute concentrations, Sr isotopes, and rare earth element and yttrium (REY) systematics in the Cape Cod aquifer. This aquifer comprises mostly carbonate-free Pleistocene sediments that are about 90% quartz with minor K-feldspar, plagioclase, glauconite, and Fe-oxides. Silica concentrations and pH in the groundwater increase systematically with increasing depth, while Sr isotopic ratios decrease. No clear relationship between 87Sr/ 86Sr and Sr concentration is observed. At all depths, the 87Sr/ 86Sr ratio of the groundwater is considerably lower than the Sr isotopic ratio of the bulk sediment or its K-feldspar component, but similar to that of a plagioclase-rich accessory separate obtained from the sediment. The Si- 87Sr/ 86Sr-depth relationships are consistent with dissolution of accessory plagioclase. In addition, solutes such as Sr, Ca, and particularly K show concentration spikes superimposed on their respective general trends. The K-Sr- 87Sr/ 86Sr systematics suggests that accessory glauconite is another major solute source to Cape Cod groundwater. Although the authigenic glauconite in the Cape Cod sediment is rich in Rb, it is low in in-grown radiogenic 87Sr because of its young Pleistocene age. The low 87Sr/ 86Sr ratios are consistent with equilibration of glauconite with seawater. The impact of glauconite is inferred to vary due to its variable abundance in the sediments. In the Cape Cod groundwater, the variation of REY concentrations with sampling depth resembles that of K and Rb, but differs from that of Ca and Sr. Shale-normalized REY patterns are light REY depleted, show negative Ce anomalies and super-chondritic Y/Ho ratios, but no Eu anomalies. REY input from feldspar, therefore, is insignificant compared to input from a K-Rb-bearing phase, inferred to be glauconite. These results emphasize that interpretation of

  14. Periodic DFT approaches to crystalline alkali metal azides

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The energy bands, electronic structures andrelationship between structures and properties of the crys-talline alkali metal azides, LiN3, α-NaN3 and KN3, are investigated at the DFT-B3LYP level. The crystalline bulks arepredicted to be insulator, speculated from their band gaps ofca. 0.23-0.25 a.u. and from their level frontier bands. Theatomic overlaps and electron densities show that the metalsand the azides are combined by ionic bonds. The crystal lat-tice energies, being corrected for the basis set superpositionerrors, are -852.30, -771.45 and - 614.78 kJ @ mol-1 for LiN3,α-NaN3 and KN3 respectively. These values are similar tothose by Gray's approximate method. The frontier crystalorbital mainly consists of the atomic orbital of the terminalnitrogen of azides. The contribution of the metallic orbital tothe LUMO is very small. The electron transition from theHOMO to the LUMO is difficult to occur. Hence all the al-kali metal azides are expected to be insensitive explosives,according to the "principle of easiest electron transition".

  15. High and rapid alkali cation storage in ultramicroporous carbonaceous materials

    Science.gov (United States)

    Yun, Young Soo; Lee, Seulbee; Kim, Na Rae; Kang, Minjee; Leal, Cecilia; Park, Kyu-Young; Kang, Kisuk; Jin, Hyoung-Joon

    2016-05-01

    To achieve better supercapacitor performance, efforts have focused on increasing the specific surface area of electrode materials to obtain higher energy and power density. The control of pores in these materials is one of the most effective ways to increase the surface area. However, when the size of pores decreases to a sub-nanometer regime, it becomes difficult to apply the conventional parallel-plate capacitor model because the charge separation distance (d-value) of the electrical double layer has a similar length scale. In this study, ultramicroporous carbonaceous materials (UCMs) containing sub-nanometer-scale pores are fabricated using a simple in situ carbonization/activation of cellulose-based compounds containing potassium. The results show that alkali cations act as charge carriers in the ultramicropores (<0.7 nm), and these materials can deliver high capacitances of ∼300 F g-1 at 0.5 A g-1 and 130 F g-1, even at a high current rate of 65 A g-1 in an aqueous medium. In addition, the UCM-based symmetric supercapacitors are stable over 10,000 cycles and have a high energy and power densities of 8.4 Wh kg-1 and 15,000 W kg-1, respectively. This study provides a better understanding of the effects of ultramicropores in alkali cation storage.

  16. Surface modification by alkali and heat treatments in titanium alloys.

    Science.gov (United States)

    Lee, Baek-Hee; Do Kim, Young; Shin, Ji Hoon; Hwan Lee, Kyu

    2002-09-01

    Pure titanium and titanium alloys are normally used for orthopedic and dental prostheses. Nevertheless, their chemical, biological, and mechanical properties still can be improved by the development of new preparation technologies. This has been the limiting factor for these metals to show low affinity to living bone. The purpose of this study is to improve the bone-bonding ability between titanium alloys and living bone through a chemically activated process and a thermally activated one. Two kinds of titanium alloys, a newly designed Ti-In-Nb-Ta alloy and a commercially available Ti-6Al-4V ELI alloy, were used in this study. In this study, surface modification of the titanium alloys by alkali and heat treatments (AHT), alkali treated in 5.0M NaOH solution, and heat treated in vacuum furnace at 600 degrees C, is reported. After AHT, the effects of the AHT on the bone integration property were evaluated in vitro. Surface morphologies of AHT were observed by optical microscopy (OM) and scanning electron microscopy (SEM). Chemical compositional surface changes were investigated by X-ray diffractometry (XRD), energy dispersive spectroscopy (EDS), and auger electron spectroscopy (AES). Titanium alloys with surface modification by AHT showed improved bioactive behavior, and the Ti-In-Nb-Ta alloy had better bioactivity than the Ti-6Al-4V ELI alloy in vitro.

  17. Core-level photoemission from alkali metals on Ru(001)

    Energy Technology Data Exchange (ETDEWEB)

    Shek, M. (Department of Physics, Hunter College of The City University of New York, New York, New York 10021 (USA)); Hrbek, J. (Department of Chemistry, Brookhaven National Laboratory, Upton, New York 11973-5000 (USA)); Sham, T.K. (Department of Chemistry, University of Western Ontario, London, Ontario, Canada NA65B7 (Canada)); Xu, G. (Department of Chemistry, Brookhaven National Laboratory, Upton, New York 11973-5000 (USA))

    1990-02-15

    We report soft-x-ray photoemission results on the core-level binding energies of Li, Na, K, and Cs adsorbed on Ru(001). For all four alkali metals, the saturated alkali-metal--Ru interface core level and the second- (surface-) layer core-level binding energies differ by as much as 0.85--1.25 eV. Surface versus bulklike core-level shifts are reported for Li, K, and Cs, which are 0.55 eV for Li and {similar to}0.25 eV for the other two. For increasing coverages of Li, Na, and K in direct contact with Ru, there are significant decreases in the core-level binding energies, the total shift ranging from {similar to}{minus}1.25 eV for Li to {similar to}{minus}0.80 eV for K; the shift for Cs is small and the reasons for the deviation are discussed. A comparison between our observations and the prediction from the thermodynamic model of Johannson and Martensson is also given.

  18. Microstructural and Mechanical Properties of Alkali Activated Colombian Raw Materials

    Directory of Open Access Journals (Sweden)

    Maria Criado

    2016-03-01

    Full Text Available Microstructural and mechanical properties of alkali activated binders based on blends of Colombian granulated blast furnace slag (GBFS and fly ash (FA were investigated. The synthesis of alkali activated binders was conducted at 85 °C for 24 h with different slag/fly ash ratios (100:0, 80:20, 60:40, 40:60, 20:80, and 0:100. Mineralogical and microstructural characterization was carried out by means of X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FTIR, Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX and Nuclear magnetic resonance (NMR. Mechanical properties were evaluated through the compressive strength, modulus of elasticity and Poisson’s ratio. The results show that two different reaction products were detected in the slag/fly ash mixtures, a calcium silicate hydrate with Al in its structure (C-A-S-H gel and a sodium aluminosilicate hydrate (N-A-S-H gel with higher number of polymerized species and low content in Ca. It was found that with the increase of the amount of added slag, the amount of C-A-S-H gel increased and the amount of N-A-S-H gel decreased. The matrix was more dense and compact with almost absence of pores. The predominance of slag affected positively the compressive strength, Young’s modulus and Poisson’s ratio, with 80% slag and 20% fly ash concrete being the best mechanical performance blend.

  19. Injectable liquid alkali alloy based-tumor thermal ablation therapy.

    Science.gov (United States)

    Rao, Wei; Liu, Jing

    2009-01-01

    The alkali metal was recently found to be a very useful agent for inducing minimally invasive tumor hyperthermia therapy. However, the solid-like metal makes it somewhat inconvenient to perform the surgery. Here, to overcome this drawback, the NaK alloy in liquid state at room temperature was proposed as a highly efficient thermal ablative agent for tumor treatment. For illustration purposes, the functionalized liquid NaK alloy at a mass ratio 1:1 was obtained and an amount of 0.35 ml was injected into in vitro pork. The sizes of the damage region and temperature response were measured. It was found that significant temperature increase by a magnitude of > 80 degrees C can easily be obtained. This produced a large coagulation and necrotic area within selected areas for in vitro tests and the necrotic region volume is three times that of the NaK injection quantity. Furthermore, for the in vivo experiment, breast EMT6 tumor in mouse was subjected to treatment by NaK alloy. Tumor was harvested after the experiment to assess its viability. Histological section showed complete necrosis at the target site. These conceptual results demonstrate that using injectable liquid alkali alloy to ablate tumor is rather promising. This study also raised interesting issues waiting for clarification in future technical and animal studies aiming to assess efficacy, side effects and safety of the new therapy.

  20. Revisiting the Zintl-Klemm concept: alkali metal trielides.

    Science.gov (United States)

    Wang, Fei; Miller, Gordon J

    2011-08-15

    To enhance understanding of the Zintl-Klemm concept, which is useful for characterizing chemical bonding in semimetallic and semiconducting valence compounds, and to more effectively rationalize the structures of Zintl phases, we present a partitioning scheme of the total energy calculated on numerous possible structures of the alkali metal trielides, LiAl, LiTl, NaTl, and KTl, using first-principles quantum mechanical calculations. This assessment of the total energy considers the relative effects of covalent, ionic, and metallic interactions, all of which are important to understand the complete structural behavior of Zintl phases. In particular, valence electron transfer and anisotropic covalent interactions, explicitly employed by the Zintl-Klemm concept, are often in competition with isotropic, volume-dependent metallic and ionic interaction terms. Furthermore, factors including relativistic effects, electronegativity differences, and atomic size ratios between the alkali metal and triel atoms can affect the competition by enhancing or weakening one of the three energetic contributors and thus cause structural variations. This partitioning of the total energy, coupled with analysis of the electronic density of states curves, correctly predicts and rationalizes the structures of LiAl, LiTl, NaTl, and KTl, as well as identifies a pressure-induced phase transition in KTl from its structure, based on [Tl(6)](6-) distorted octahedra, to the double diamond NaTl-type. © 2011 American Chemical Society

  1. Dilute alkali pretreatment of softwood pine: A biorefinery approach.

    Science.gov (United States)

    Safari, Ali; Karimi, Keikhosro; Shafiei, Marzieh

    2017-06-01

    Dilute alkali pretreatment was performed on softwood pine to maximize ethanol and biogas production via a biorefinery approach. Alkali pretreatments were performed with 0-2% w/v NaOH at 100-180°C for 1-5h. The liquid fraction of the pretreated substrates was subjected to anaerobic digestion. The solid fraction of the pretreatment was used for separate enzymatic hydrolysis and fermentation. High ethanol yields of 76.9‒78.0% were achieved by pretreatment with 2% (w/v) NaOH at 180°C. The highest biogas yield of 244mL/g volatile solid (at 25°C, 1bar) was achieved by the pretreatment with 1% (w/v) NaOH at 180°C. The highest gasoline equivalent (sum of ethanol and methane) of 197L per ton of pinewood and the lowest ethanol manufacturing cost of 0.75€/L was obtained after pretreatment with 1% NaOH at 180°C for 5h. The manufacturing cost of ethanol from untreated wood was 4.12€/L. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Alkali-metalated forms of thiacalix[4]arenes.

    Science.gov (United States)

    Zeller, Jürgen; Radius, Udo

    2006-11-13

    The alkali metal salts [TCALi4] (1), [TCANa4] (2), and [TCALK4] (3) of fully deprotonated p-tert-butyltetrathiacalix[4]arene (H(4)TCA) are readily available from the reactions of thiacalix[4]arene and n-BuLi, NaH, or KH as deprotonating reagents. Crystals of the sodium salts 2 and the potassium salt 3 suitable for X-ray diffraction were obtained in the form of the pyridine solvates [(TCA)2Na8.8py] (2.8py) and [(TCA)2K(8).8py] (3.8py). These molecules are dimers in the solid state but are structurally not related. In addition, the reaction of H(4)TCA and lithium hydroxide afforded the structurally characterized complex [(TCA)Li5(OH).4THF] (4). The molecular structure of 4 as well as the structures of 2.8py and 3.8py reveal a close relationship to the corresponding alkali metal salts of the calix[4]arenes.

  3. Structure and Bonding in Small Neutral Alkali-Halide Clusters

    CERN Document Server

    Aguado, A; López, J M; Alonso, J A

    1997-01-01

    The structural and bonding properties of small neutral alkali-halide clusters (AX)n, with n less than or equal to 10, A=Li, Na, K, Rb and X=F, Cl, Br, I, are studied using the ab initio Perturbed Ion (aiPI) model and a restricted structural relaxation criterion. A trend of competition between rock-salt and hexagonal ring-like isomers is found and discussed in terms of the relative ionic sizes. The main conclusion is that an approximate value of r_C/r_A=0.5 (where r_C and r_A are the cationic and anionic radii) separates the hexagonal from the rock-salt structures. The classical electrostatic part of the total energy at the equilibrium geometry is enough to explain these trends. The magic numbers in the size range studied are n= 4, 6 and 9, and these are universal since they occur for all alkali-halides and do not depend on the specific ground state geometry. Instead those numbers allow for the formation of compact clusters. Full geometrical relaxations are considered for (LiF)n (n=3-7) and (AX)_3 clusters, an...

  4. Desorption of alkali atoms from 4He nanodroplets.

    Science.gov (United States)

    Hernando, Alberto; Barranco, Manuel; Pi, Martí; Loginov, Evgeniy; Langlet, Marina; Drabbels, Marcel

    2012-03-21

    The dynamics following the photoexcitation of Na and Li atoms located on the surface of helium nanodroplets has been investigated in a joint experimental and theoretical study. Photoelectron spectroscopy has revealed that excitation of the alkali atoms via the (n + 1)s ←ns transition leads to the desorption of these atoms. The mean kinetic energy of the desorbed atoms, as determined by ion imaging, shows a linear dependence on excitation frequency. These experimental findings are analyzed within a three-dimensional, time-dependent density functional approach for the helium droplet combined with a Bohmian dynamics description of the desorbing atom. This hybrid method reproduces well the key experimental observables. The dependence of the observables on the impurity mass is discussed by comparing the results obtained for the (6)Li and (7)Li isotopes. The calculations show that the desorption of the excited alkali atom is accompanied by the creation of highly non-linear density waves in the helium droplet that propagate at supersonic velocities.

  5. Thermal, mechanical and Raman studies on mixed alkali borotungstate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Edukondalu, A. [Department of Physics, Osmania University, Hyderabad 500007 (India); Sathe, Vasant [Consortium for Scientific Research, Khandwa Road, Indore 452017 (India); Rahman, Syed [Department of Physics, Osmania University, Hyderabad 500007 (India); Siva Kumar, K., E-mail: siva193ou@gmail.com [Department of Physics, Osmania University, Hyderabad 500007 (India)

    2014-04-01

    Mixed alkali borotungstate glasses with xLi{sub 2}O–(30−x)Na{sub 2}O–10WO{sub 3}–60B{sub 2}O{sub 3} (0 ≤ x ≤ 30) composition were prepared by melt quench technique. The amorphous phase of the prepared glass samples was conformed from their X-ray diffraction and SEM studies. Differential scanning calorimetry and Raman spectroscopic studies were employed to investigate the structure of all the prepared glasses. The elastic moduli and Debye temperature were calculated in terms of Makishima–Mackenzie model. Acting as complementary techniques, Raman measurement revealed that the network structure of the present glasses is mainly based on BO{sub 3} and BO{sub 4} units placed in different structural groups. Raman spectra confirms the presence of tungsten ions mainly as WO{sub 6} groups. In the present work, the mixed alkali effect (MAE) has been investigated in the above glass system through modulated DSC studies.

  6. Dislocation unpinning model of acoustic emission from alkali halide crystals

    Indian Academy of Sciences (India)

    B P Chandra; Anubha S Gour; Vivek K Chandra; Yuvraj Patil

    2004-06-01

    The present paper reports the dislocation unpinning model of acoustic emission (AE) from alkali halide crystals. Equations are derived for the strain dependence of the transient AE pulse rate, peak value of the AE pulse rate and the total number of AE pulse emitted. It is found that the AE pulse rate should be maximum for a particular strain of the crystals. The peak value of the AE pulse rate should depend on the volume and strain rate of the crystals, and also on the pinning time of dislocations. Since the pinning time of dislocations decreases with increasing strain rate, the AE pulse rate should be weakly dependent on the strain rate of the crystals. The total number of AE should increase linearly with deformation and then it should attain a saturation value for the large deformation. By measuring the strain dependence of the AE pulse rate at a fixed strain rate, the time constant $_{\\text{s}}$ for surface annihilation of dislocations and the pinning time $_{\\text{p}}$ of the dislocations can be determined. A good agreement is found between the theoretical and experimental results related to the AE from alkali halide crystals.

  7. Structural criteria for the rational design of selective ligands. Extension of the MM3 force field to aliphatic ether complexes of the alkali and alkaline earth cations

    Energy Technology Data Exchange (ETDEWEB)

    Hay, B.P.; Rustad, J.R. (Pacific Northwest Lab., Richland, WA (United States))

    1994-07-13

    Structural requirements for strain-free metal ion complexation by an aliphatic ether group are investigated through the use of both ab initio molecular orbital and molecular mechanics calculations. Hartree-Fock calculations on simple models, M-O(Me)[sub 2] and M-O(Me)(Et), reveal a preference for trigonal planar geometry when aliphatic ether oxygens are coordinated to alkali and alkaline earth cations. This preference is found to be strongest in small, high-valent cations and weakest in large, low-valent cations. Results from the Hartree-Fock calculations are used to extend the MM3 force field for calculation on aliphatic ether complexes with the alkali (Li to Cs) and alkaline earth (Mg to Ba) cations. The resulting molecular model (i) reproduces the experimental crystal structures of 51 different complexes of multidentate ethers with alkali and alkaline earth cations, (ii) explains experimental trends in the structure of five-membered chelate rings of aliphatic ethers, (iii) reveals a fundamental difference between the metal ion size selectivity of five-membered chelate rings of ethers versus that of amines, and (iv) rationalizes trends in the stability of four potassium complexes with the diasteriomers of dicyclohexyl-18-crown-6. 40 refs., 9 figs., 5 tabs.

  8. Hydrothermal alteration at the Roosevelt Hot Springs Thermal Area, Utah: modal mineralogy, and geochemistry of sericite, chlorite, and feldspar from altered rocks, Thermal Power Company well Utah State 14-2

    Energy Technology Data Exchange (ETDEWEB)

    Ballantyne, J.M.

    1978-11-01

    Sericites, chlorites, feldspars, biotite and hornblende from hydrothermally altered rocks at several depths in Thermal Power Company well Utah State 14-2, Roosevelt Hot Springs Thermal Area, Utah, have been analyzed using the electron microprobe. Sericites and ferromagnesian minerals have been analyzed for 12 major elements, and feldspars for 3. The results have been used, along with whole rock chemical analyses, to computer calculate modal mineralogy for samples from the drillhole. Calculated modes for hydrothermal minerals are in reasonable agreement with observations from thin sections.

  9. Illustration of alkali corrosion mechanisms in high temperature thermal insulation materials

    Energy Technology Data Exchange (ETDEWEB)

    Aneziris, C.G.; Fischer, U.; Schlegel, E. [Technical Univ. of Freiberg (Germany)

    2007-07-01

    Alkali attack is a chronic problem in the most popular high temperature applications such as blast furnaces, gasifiers, glass furnaces and cement kilns. Especially in the last years the problem of alkali corrosion is dramatically increased due to the waste burning and the combustion of the so called secondary fuels in kilns at high temperature processes. The German cement industry uses up to 100 percent of secondary fuels - a little or no coal, oil or gas- but mainly burnable waste. According to the literature destruction of the refractory can occur by the formation of low-melting low-viscosity liquids, or, more usually by the formation of dry expansive alkali-aluminosilicate compounds that result to chemical spalling. This work explores due to laboratory experiments supported partially by post mortem industrial trials the chemical interactions between alkali species and established refractory materials and illustrates four main alkali corrosion mechanisms. (orig.)

  10. Influence of TiO2 on the Alkali Resistance and Structure of Invert Glass

    Institute of Scientific and Technical Information of China (English)

    ZHAO Qing-lin; WU Zheng-ming; BU Heng-zhi

    2003-01-01

    Through measuring the alkali resistance of the invert glass and the quantity of SiO2 and TiO2 migrating fron the glass into the solution,the influence of TiO2 on the alkali resistance of the glass is discussed and its structure is also analyzed by infrared spectroscopy.It is concluded that TiO2 has double functions for the alkali resistance of the invert glass.On the one hand ,both TiO2 polarizing the secondary ions in glass and TiO2 isomorphism replacement of SiO2 make the alkali resistance of the glass decrease.On the ther hand,TiO2 patching network and anti-erosion covering help to increase the alkali resistance.

  11. Study on the Structure and Properties of Polynosic Fiber Treated by Alkali

    Institute of Scientific and Technical Information of China (English)

    WEI Meng-yuan; XUE Wen-liang; CHENG Long-di

    2007-01-01

    The regenerated cellulose fibers, made from wood pulp, have excellent physical properties like cotton fiber. Especially polynosic fibers can be mercerized by alkali, but conventional Viscose fiber can not be treated or mercerized by alkali. The paper studies on behavior of polynosic fibers treated by alkali, including physical properties, such as weight loss, tensile strength and elongation, and fiber structures properties. In this paper, on the basis of study on polynosic fibers treated by alkali, the conclusions were drawn as following. Firstly, polynosic fiber is good at alkali resistance. Secondly, the changes of fiber structure and physical properties begin declining at 5 wt% NaOH concentration and reverse changes take place at 10 wt%.

  12. Adding nickel formate in alkali lignin to increase contents of alkylphenols and aromatics during fast pyrolysis.

    Science.gov (United States)

    Geng, Jing; Wang, Wen-Liang; Yu, Yu-Xiang; Chang, Jian-Min; Cai, Li-Ping; Shi, Sheldon Q

    2017-03-01

    The composition of pyrolysis vapors obtained from alkali lignin pyrolysis with the additive of nickel formate was examined using the pyrolysis gas chromatography-mass spectrometry (Py-GC/MS). Characterization of bio-chars was performed using X-ray diffraction (XRD). Results showed that the nickel formate significantly increased liquid yield, simplified the types of alkali lignin pyrolysis products and increased individual component contents. The additive of nickel formate increased contents of alkylphenols and aromatics from alkali lignin pyrolysis. With an increase in temperature, a greater amount of the relative contents can be achieved. The nickel formate was thermally decomposed to form hydrogen, resulting in hydrodeoxygenation of alkali lignin during pyrolysis. It was also found that Ni is in favor of producing alkylphenols. The analysis based on the experimental result provided evidences used to propose reaction mechanism for pyrolysis of nickel formate-assisted alkali lignin. Copyright © 2016. Published by Elsevier Ltd.

  13. Communication: Dimensionality of the ionic conduction pathways in glass and the mixed-alkali effect.

    Science.gov (United States)

    Novy, Melissa; Avila-Paredes, Hugo; Kim, Sangtae; Sen, Sabyasachi

    2015-12-28

    A revised empirical relationship between the power law exponent of ac conductivity dispersion and the dimensionality of the ionic conduction pathway is established on the basis of electrical impedance spectroscopic (EIS) measurements on crystalline ionic conductors. These results imply that the "universal" ac conductivity dispersion observed in glassy solids is associated with ionic transport along fractal pathways. EIS measurements on single-alkali glasses indicate that the dimensionality of this pathway D is ∼2.5, while in mixed-alkali glasses, D is lower and goes through a minimum value of ∼2.2 when the concentrations of the two alkalis become equal. D and σ display similar variation with alkali composition, thus suggesting a topological origin of the mixed-alkali effect.

  14. Calculation of Interaction Parameters from Immiscible Phase Diagram of Alkali Metal or Alkali Earth Metal-Halide System by Means of Subregular Solution Model

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper, the interaction parameters in the subregular solution model, λ1 and λ2, are regarded as a linear function of temperature, T. Therefore, the molar excess Gibbs energy of A-B binary system may be reexpressed as follows: The calculation of the model parameters, λ11, λ12, λ21 and λ22, was carried out numerically from the phase diagrams for 11 alkali metal-alkali halide or alkali earth metal-halide systems.In addition, artificial neural network trained by known data has been used to predict the values of these model parameters. The predicted results are in good agreement with the.calculated ones. The applicability of the subregular solution model to the alkali metal-alkali halide or alkali earth metal-halide systems were tested by comparing the available experimental composition along the boundary of miscibility gap with the calculated ones which were obtained by using genetic algorithm. The good agreement between the calculated and experimental results across the entire liquidus is valid evidence in support of the model.

  15. First-principles study of ternary graphite compounds cointercalated with alkali atoms (Li, Na, and K) and alkylamines towards alkali ion battery applications

    Science.gov (United States)

    Ri, Gum-Chol; Yu, Chol-Jun; Kim, Jin-Song; Hong, Song-Nam; Jong, Un-Gi; Ri, Mun-Hyok

    2016-08-01

    First-principles calculations were carried out to investigate the structural, energetic, and electronic properties of ternary graphite compounds cointercalated with alkali atoms (AM = Li, Na, and K) and normal alkylamine molecules (nCx; x = 1, 2, 3, 4), denoted as AM-nCx-GICs. From the optimization of the orthorhombic unit cells for the crystalline compounds, it was found that, with the increase in the atomic number of alkali atoms, the layer separations decrease in contrast to AM-GICs, while the bond lengths between alkali atoms and graphene layer, and nitrogen atom of alkylamine increase. The calculated formation energies and interlayer binding energies of AM-nC3-GICs indicate that the compounds is increasingly stabilized from Li to K, and the energy barriers for migration of alkali atoms suggest that alkali cation with larger ionic radius diffuses more smoothly in graphite, being similar to AM-GICs. Through the analysis of electronic properties, it was established that more extent of electronic charge is transferred from more electropositive alkali atom to the carbon ring of graphene layer, and the hybridization of valence electron orbitals between alkylamine molecules and graphene layer is occurred.

  16. Behaviour of gaseous alkali compounds in coal gasification; Kaasumaisten alkaliyhdisteiden kaeyttaeytyminen kivihiilien kaasutuksessa

    Energy Technology Data Exchange (ETDEWEB)

    Nykaenen, J. [Imatran Voima Oy, Vantaa (Finland)

    1997-10-01

    In this project the behaviour of alkali compounds emitting from CO{sub 2}/O{sub 2}- and airblown gasification are studied. This research project is closely connected to an EU-project coordinated by the Delft University of Technology (DUT). In that project alkali emissions from a 1.6 MW pilot plant will be measured. The results from those measurements will be compared with the calculations performed in this LIEKKI 2 project. The equilibrium calculations show that the major gaseous alkali compounds emitting from combustion and gasification are chlorides and hydroxides. This applies both to air- and CO{sub 2}/O{sub 2}-blown processes. In all the cases studied the concentration of gaseous alkali compounds is determined mainly by the amount of chlorides. The key parameters, with respect to alkali behaviour, are the temperature of the process and chlorine content of the coal. By cooling the gases down to 600 deg C prior to a ceramic filter the alkali concentration can be kept about at 100 ppbv. In combustion, the addition of calcium carbonate increases the amount of gaseous alkali compounds by decreasing the amount of alkali sulphates. In the case of gasification the importance of limestone is negligible. The difference between air- and CO{sub 2}/O{sub 2}-blown processes, in terms of gaseous alkali emissions, is small. This is because CO{sub 2} concentration of the gas does not have a strong impact on alkali chlorides. Furthermore, the effect of CO{sub 2}/O{sub 2}-ratio of the recirculation process is negligible. (orig.)

  17. Optical excitation processes in the near band-edge region of KAlSi3O8 and NaAlSi3O8 feldspar

    DEFF Research Database (Denmark)

    Poolton, N.R.J.; Mauz, B.; Lang, A.;

    2006-01-01

    A complex variety of excitation and relaxation pathways are available for charge in naturally occurring NaAlSi3O8 and KAlpSi(3)O(8) feldspar crystals, when excited with photons in the trans-band-edge energy range 4-12 eV These can involve a mixture of electronic transitions associated with defect...... states, the conduction and valence bands and their associated band-tails. In order to demonstrate that a relationship exists between these processes, combinations of three spectroscopic techniques are deployed in this work: luminescence excitation/emission mapping, energy-resolved photo...... emission in the materials. Luminescence and phosphorescence excitation spectra provide additional, complementary, information regarding the excited states of the blue-emitting defects, including their transition lifetimes and decay paths. Red emission associated with Fe3+ luminescence is mostly isolated...

  18. Partial replacement of the feldspar waste of flat glass ceramics for masses in white; Substituicao parcial do feldspato pelo residuo de vidro plano em massas para ceramica branca

    Energy Technology Data Exchange (ETDEWEB)

    Porto, V.S.; Araujo, A.M.B.; Morais, C.R.S., E-mail: valdenia_porto@hotmail.com [Universidade Federal da Paraiba (CCHSA/UFPB), PB (Brazil); Cavalcanti, M.S.L. [Universidade Federal de Campina Grande (CCT/UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2012-07-01

    In all the industrial production process requires the consumption of raw materials exaggerated the traditional scarcity of incurring the same. To reverse this situation, one of the possible actions is the search for alternative technologies that aim to replace these materials by waste that exhibit similar characteristics. This study aims to verify the possibility of partially replacing feldspar by waste flat glass ceramic mass for white, since this type of waste, when subjected to high temperatures can act as a flux. For this research, initially the raw materials were characterized using the techniques of energy dispersive spectroscopy X-ray (EDX) and X-ray diffraction. Then, test pieces were prepared to be burned at temperatures between 1000 and 1250 ° C, which were submitted to tests of porosity to absorb water. The results are within the standards required by the standards established for ceramic products, which confirms the feasibility of such waste to act as a flux in ceramic white masses. (author)

  19. Feldspar palaeo-isochrons from early Archaean TTGs: Pb-isotope evidence for a high U/Pb terrestrial Hadean crust

    Science.gov (United States)

    Kamber, B. S.; Whitehouse, M. J.; Moorbath, S.; Collerson, K. D.

    2001-12-01

    Feldspar lead-isotope data for 22 early Archaean (3.80-3.82 Ga) tonalitic gneisses from an area south of the Isua greenstone belt (IGB),West Greenland, define a steep linear trend in common Pb-isotope space with an apparent age of 4480+/-77 Ma. Feldspars from interleaved amphibolites yield a similar array corresponding to a date of 4455+/-540 Ma. These regression lines are palaeo-isochrons that formed during feldspar-whole rock Pb-isotope homogenisation a long time (1.8 Ga) after rock formation but confirm the extreme antiquity (3.81 Ga) of the gneissic protoliths [1; this study]. Unlike their whole-rock counterparts, feldspar palaeo-isochrons are immune to rotational effects caused by the vagaries of U/Pb fractionation. Hence, comparison of their intercept with mantle Pb-isotope evolution models yields meaningful information regarding the source history of the magmatic precursors. The locus of intersection between the palaeo-isochrons and terrestrial mantle Pb-isotope evolution lines shows that the gneissic precursors of these 3.81 Ga gneisses were derived from a source with a substantially higher time-integrated U/Pb ratio than the mantle. Similar requirements for a high U/Pb source have been found for IGB BIF [2], IGB carbonate [3], and particularly IGB galenas [4]. Significantly, a single high U/Pb source that separated from the MORB-source mantle at ca. 4.3 Ga with a 238U/204Pb of ca. 10.5 provides a good fit to all these observations. In contrast to many previous models based on Nd and Hf-isotope evidence we propose that this reservoir was not a mantle source but the Hadean basaltic crust which, in the absence of an operating subduction process, encased the early Earth. Differentiation of the early high U/Pb basaltic crust could have occurred in response to gravitational sinking of cold mantle material or meteorite impact, and produced zircon-bearing magmatic rocks. The subchondritic Hf-isotope ratios of ca. 3.8 Ga zircons support this model [5] provided that

  20. Luminescence excitation characteristics of Ca-, Na- and K-aluminosilicates (feldspars), in the stimulation range 20-500 eV: optical detection of XAS

    CERN Document Server

    Poolton, N R J; Quinn, F M; Pantos, E; Andersen, C E; Bøtter-Jensen, L; Johnsen, O; Murray, A S

    2003-01-01

    We demonstrate that the visible/UV luminescence from common feldspar crystals (NaAlSi sub 3 O sub 8 , KAlSi sub 3 O sub 8 and CaAl sub 2 Si sub 2 O sub 8) can be used to detect detailed L-edge and associated near-edge absorption structure of the main constituent atoms (Ca, K, Na, Al, Si), when exciting in the energy range 20-500 eV. Comparisons of the spectral features are drawn with similar measurements made on the associated materials SiO sub 2 , Al sub 2 O sub 3 and CaCO sub 3. The potential for using optically detected x-ray absorption spectroscopy as a method for identifying the luminescent components of mixed mineral samples is considered.

  1. Sr-Isotope Composition of Feldspar: Implication for age and Evolution of Gabbros from Uralian-Alaskan Type Complexes in the Ural Mountains, Russia

    Science.gov (United States)

    Bruegmann, G. E.; Krause, J.; Pushkarev, E.

    2006-12-01

    Compared to whole-rock or bulk mineral analyses single mineral composition could reveal disequilibrium features between crystals or within individual crystals which provide important information on magma chamber processes. We applied a LA-ICPMS technique to determine Sr isotopes in plagioclase and K-feldspar of gabbroic rocks from the Nizhnii Tagil and Kytlym complexes in the Ural Mountains in Russia. These complexes are Uralian-Alaskan-type zoned mafic-ultramafic complexes, consisting of dunite, clinopyroxenite and gabbro bodies. The rock association is considered to represent a cumulate sequence of a single parental melt feeding a magma chamber system. The instruments used were a NU Plasma MC-ICPMS and a solid-state 193 and 213 nm Nd:YAG laser ablation system from New Wave. The data of the present study includes up to five spot analyses (100-120 μm spot size) of each mineral in a thin section. Baselines for analyses were measured on-peak for 20 s while flushing the sample chamber with He. About 300 to 500 isotope ratios were measured during the ablation time of 80-100 s. Raw data were exported to an external data reduction spreadsheet and corrected for interferences (Kr, Rb) and mass bias using 87Sr/^{88}Sr=0.1194. During the time of analyses we measured the Sr isotope composition of an in-house marine carbonate reference material. Its 87Sr/86Sr of 0.70923±6 (2SD) agrees within error limits with our TIMS measurements. The gabbros have porphyric textures with clinopyroxene phenocrysts in a matrix of olivine, clinopyroxene and spinel. Two gabbro types can be distinguished based on additional matrix minerals. One type of gabbro is silica saturated, contains plagioclase (An57-88) and in places orthopyroxene as matrix phases. The second gabbro type is silica undersaturated and contains in the matrix plagioclase (An29-56) and pseudoleucite, a fine grained intergrowth of nepheline and K-feldspar (Or30-81). In this gabbro plagioclase has generally higher Sr

  2. Luminescence excitation characteristics of Ca-, Na- and K-aluminosilicates (feldspars), in the stimulation range 20-500 eV: optical detection of XAS

    Energy Technology Data Exchange (ETDEWEB)

    Poolton, N R J [Synchrotron Radiation Department, Daresbury Laboratory, Warrington WA4 4AD, Cheshire (United Kingdom); Malins, A E R [Synchrotron Radiation Department, Daresbury Laboratory, Warrington WA4 4AD, Cheshire (United Kingdom); Quinn, F M [Synchrotron Radiation Department, Daresbury Laboratory, Warrington WA4 4AD, Cheshire (United Kingdom); Pantos, E [Synchrotron Radiation Department, Daresbury Laboratory, Warrington WA4 4AD, Cheshire (United Kingdom); Andersen, C E [Radiation Research Department, Riso National Laboratory, 4000 Roskilde (Denmark); Botter-Jensen, L [Radiation Research Department, Riso National Laboratory, 4000 Roskilde (Denmark); Johnsen, O [Geological Museum, University of Copenhagen, Oster Voldgade 5-7, 1350 Copenhagen (Denmark); Murray, A S [Nordic Laboratory for Luminescence Dating, Aarhus University, Riso National Laboratory, 4000 Roskilde (Denmark)

    2003-05-07

    We demonstrate that the visible/UV luminescence from common feldspar crystals (NaAlSi{sub 3}O{sub 8}, KAlSi{sub 3}O{sub 8} and CaAl{sub 2}Si{sub 2}O{sub 8}) can be used to detect detailed L-edge and associated near-edge absorption structure of the main constituent atoms (Ca, K, Na, Al, Si), when exciting in the energy range 20-500 eV. Comparisons of the spectral features are drawn with similar measurements made on the associated materials SiO{sub 2}, Al{sub 2}O{sub 3} and CaCO{sub 3}. The potential for using optically detected x-ray absorption spectroscopy as a method for identifying the luminescent components of mixed mineral samples is considered.

  3. The action and interaction of calcium and alkali chlorides on eggs of Limnaea stagnalis and their chemical interpretation

    NARCIS (Netherlands)

    Geilenkirchen, W.L.M.

    1964-01-01

    1. 1. The action and interaction of CaCl2 and alkali chlorides on eggs of Limnaea stagnalis have been studied. 2. 2. CaCl2 antagonizes death caused by alkali chlorides. The number of normally developing embryos increases in all cases. 3. 3. Alkali chlorides antagonize death caused by CaCl2. With NaC

  4. Does crystallographic anisotropy prevent the conventional treatment of aqueous mineral reactivity? A case study based on K-feldspar dissolution kinetics

    Science.gov (United States)

    Pollet-Villard, Marion; Daval, Damien; Ackerer, Philippe; Saldi, Giuseppe D.; Wild, Bastien; Knauss, Kevin G.; Fritz, Bertrand

    2016-10-01

    Which conceptual framework should be preferred to develop mineral dissolution rate laws, and how the aqueous mineral reactivity should be measured? For over 30 years, the classical strategy to model solid dissolution over large space and time scales has relied on so-called kinetic rate laws derived from powder dissolution experiments. In the present study, we provide detailed investigations of the dissolution kinetics of K-feldspar as a function of surface orientation and chemical affinity which question the commonplace belief that elementary mechanisms and resulting rate laws can be retrieved from conventional powder dissolution experiments. Nanometer-scale surface measurements evidenced that K-feldspar dissolution is an anisotropic process, where the face-specific dissolution rate satisfactorily agrees with the periodic bond chain (PBC) theory. The chemical affinity of the reaction was shown to impact differently the various faces of a single crystal, controlling the spontaneous nucleation of etch pits which, in turn, drive the dissolution process. These results were used to develop a simple numerical model which revealed that single crystal dissolution rates vary with reaction progress. Overall, these results cast doubt on the conventional protocol which is used to measure mineral dissolution rates and develop kinetic rate laws, because mineral reactivity is intimately related to the morphology of dissolving crystals, which remains totally uncontrolled in powder dissolution experiments. Beyond offering an interpretive framework to understand the large discrepancies consistently reported between sources and across space scales, the recognition of the anisotropy of crystal reactivity challenges the classical approach for modeling dissolution and weathering, and may be drawn upon to develop alternative treatments of aqueous mineral reactivity.

  5. Adsorption of N-tallow 1,3-propanediamine-dioleate collector on albite and quartz minerals, and selective flotation of albite from greek stefania feldspar ore.

    Science.gov (United States)

    Vidyadhar, A; Hanumantha Rao, K; Forssberg, K S E

    2002-04-01

    The adsorption behavior of tallow 1,3-propanediamine-dioleate (Duomeen TDO) collector on albite and quartz minerals is assessed through Hallimond flotation, zeta potential, and diffuse reflectance FTIR investigations, together with the species distribution of the collector. The collector performance on albite separation from a natural feldspar material is evaluated in bench scale flotation tests. The Hallimond flotation responses of the minerals as a function of pH and collector concentration indicate that albite can be selectively floated from quartz at pH 2 where the doubly positively charged collector species adsorb on albite but not on quartz. However, the zeta potential and infrared spectra reveal that the adsorption behavior of the collector is similar on both minerals. The discrepancy in the flotation and adsorption results is attributed to the coarse and fine particle size fractions, and the shorter and longer equilibration periods employed in these studies respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding as well as electrostatic interactions. The changes in zeta potentials are in good agreement with the formation of ionic species and free molecular forms of the collector. The IR spectra show the coexistence of neutral oleic acid together with charged amine species at low pH values in accordance with the species distribution diagram. Selective flotation of albite is accomplished from a natural feldspar material with tallow diamine-dioleate collector at pH 2 using sulfuric acid, only when the feed is deslimed prior to the bench scale flotation tests. An albite recovery exceeding 85% is achieved from a feed material containing about 50% albite.

  6. Incommensurate density modulation in a Na-rich plagioclase feldspar: Z-contrast imaging and single-crystal X-ray diffraction study.

    Science.gov (United States)

    Xu, Huifang; Jin, Shiyun; Noll, Bruce C

    2016-12-01

    Plagioclase feldspars are the most abundant mineral in the Earth's crust. Intermediate plagioclase feldspars commonly display incommensurately modulated or aperiodic structures. Z-contrast images show both Ca-Na ordering and density modulation. The local structure of lamellae domains has I1-like symmetry. The neighboring lamellae domains are in an inversion twinning relationship. With a state-of-the-art X-ray diffraction unit, second-order satellite reflections (f-reflections) are observed for the first time in andesine (An45), a Na-rich e-plagioclase. The f-reflections indicate a structure with a density modulation which is close to a Ca-rich e-plagioclase. The similarity between this e-andesine structure and previously solved e-labradorite structure is confirmed. Refinement of the structure shows density modulation of ∼ 7 mol % in compositional variation of the anorthite (An) component. The results from Z-contrast imaging and low-temperature single X-ray diffraction (XRD) provide a structure consistent with density modulation. The discovery of f-reflections in Na-rich e-plagioclase extends the composition range of e1 structure with density modulation to as low as at least An45, which is the lower end of the composition range of Bøggild intergrowth. The new result supports the loop-shaped solvus for Bøggild intergrowth, below which is a homogenous stable area for e1 structure in the phase diagram. The phase transition between e2 structure without density modulation and e1 structure with density modulation should happen at low temperature. There is a change in modulation period accompanying the phase transition, as well as higher occupancy of Al in the T1o site. The andesine with density modulation also indicates extremely slow cooling of its host rock.

  7. Geochemical diversity in first rocks examined by the Curiosity Rover in Gale Crater: Evidence for and significance of an alkali and volatile-rich igneous source

    Science.gov (United States)

    Schmidt, M. E.; Campbell, J. L.; Gellert, R.; Perrett, G. M.; Treiman, A. H.; Blaney, D. L.; Olilla, A.; Calef, F. J.; Edgar, L.; Elliott, B. E.; Grotzinger, J.; Hurowitz, J.; King, P. L.; Minitti, M. E.; Sautter, V.; Stack, K.; Berger, J. A.; Bridges, J. C.; Ehlmann, B. L.; Forni, O.; Leshin, L. A.; Lewis, K. W.; McLennan, S. M.; Ming, D. W.; Newsom, H.; Pradler, I.; Squyres, S. W.; Stolper, E. M.; Thompson, L.; VanBommel, S.; Wiens, R. C.

    2014-01-01

    first four rocks examined by the Mars Science Laboratory Alpha Particle X-ray Spectrometer indicate that Curiosity landed in a lithologically diverse region of Mars. These rocks, collectively dubbed the Bradbury assemblage, were studied along an eastward traverse (sols 46-102). Compositions range from Na- and Al-rich mugearite Jake_Matijevic to Fe-, Mg-, and Zn-rich alkali-rich basalt/hawaiite Bathurst_Inlet and span nearly the entire range in FeO* and MnO of the data sets from previous Martian missions and Martian meteorites. The Bradbury assemblage is also enriched in K and moderately volatile metals (Zn and Ge). These elements do not correlate with Cl or S, suggesting that they are associated with the rocks themselves and not with salt-rich coatings. Three out of the four Bradbury rocks plot along a line in elemental variation diagrams, suggesting mixing between Al-rich and Fe-rich components. ChemCam analyses give insight to their degree of chemical heterogeneity and grain size. Variations in trace elements detected by ChemCam suggest chemical weathering (Li) and concentration in mineral phases (e.g., Rb and Sr in feldspars). We interpret the Bradbury assemblage to be broadly volcanic and/or volcaniclastic, derived either from near the Gale crater rim and transported by the Peace Vallis fan network, or from a local volcanic source within Gale Crater. High Fe and Fe/Mn in Et_Then likely reflect secondary precipitation of Fe3+ oxides as a cement or rind. The K-rich signature of the Bradbury assemblage, if igneous in origin, may have formed by small degrees of partial melting of metasomatized mantle.

  8. 3718-F Alkali Metal Treatment and Storage Facility Closure Plan

    Energy Technology Data Exchange (ETDEWEB)

    None

    1991-12-01

    Since 1987, Westinghouse Hanford Company has been a major contractor to the U.S. Department of Energy-Richland Operations Office and has served as co-operator of the 3718-F Alkali Metal Treatment and Storage Facility, the waste management unit addressed in this closure plan. The closure plan consists of a Part A Dangerous waste Permit Application and a RCRA Closure Plan. An explanation of the Part A Revision (Revision 1) submitted with this document is provided at the beginning of the Part A section. The closure plan consists of 9 chapters and 5 appendices. The chapters cover: introduction; facility description; process information; waste characteristics; groundwater; closure strategy and performance standards; closure activities; postclosure; and references.

  9. Experimental study of the diode pumped alkali laser (DPAL)

    Science.gov (United States)

    Endo, Masamori; Nagaoka, Ryuji; Nagaoka, Hiroki; Nagai, Toru; Wani, Fumio

    2014-02-01

    A small-scale cesium diode-pumped alkali laser (DPAL) apparatus has been developed for fundamental researches. A commercial laser diode with volume Bragg grating outcoupler is used to pump the gain cell longitudinally. Both windows of the gain cell are set at Brewster's angle for minimum loss and maximum durability. Output coupling coefficient is continuously variable from 13% to 85% by the slanted quartz plate outcoupler inserted in the optical resonator. Small signal gain is measured with a laser diode probe at various gain cell temperatures. A 6.5 W continuouswave output with 56% optical-to-optical conversion efficiency (based on the absorbed power) has been achieved. A numerical simulation code is developed and its calculation results are in good agreement with the experiments.

  10. Strong Turbulence in Alkali Halide Negative Ion Plasmas

    Science.gov (United States)

    Sheehan, Daniel

    1999-11-01

    Negative ion plasmas (NIPs) are charge-neutral plasmas in which the negative charge is dominated by negative ions rather than electrons. They are found in laser discharges, combustion products, semiconductor manufacturing processes, stellar atmospheres, pulsar magnetospheres, and the Earth's ionosphere, both naturally and man-made. They often display signatures of strong turbulence^1. Development of a novel, compact, unmagnetized alkali halide (MX) NIP source will be discussed, it incorporating a ohmically-heated incandescent (2500K) tantulum solenoid (3cm dia, 15 cm long) with heat shields. The solenoid ionizes the MX vapor and confines contaminant electrons, allowing a very dry (electron-free) source. Plasma densities of 10^10 cm-3 and positive to negative ion mass ratios of 1 Fusion 4, 91 (1978).

  11. Structure and energetics of helium films on alkali substrates

    Science.gov (United States)

    Boninsegni, Massimo; Szybisz, Leszek

    2004-07-01

    Low-temperature adsorption of He4 films on Alkali metal substrates is investigated theoretically by means of ground-state quantum Monte Carlo simulations. The most accurate potentials currently available are utilized to model the interaction of He4 atoms with the substrate. Continuous growth of film thickness as a function of chemical potential is observed on Li, Na, and K substrates. A superfluid monolayer forms on a Li substrate; on Na and K, thermodynamically stable films are a few layers thick. The uncertainties of the calculation and in the potentials, preclude a definitive conclusion on the existence of a stable He4 film on Rb. A comparison of the results of this calculation with those obtained using the Orsay-Trento density functional shows broad quantitative agreement.

  12. Electrochemical synthesis of alkali-intercalated iron selenide superconductors

    Science.gov (United States)

    Shen, Shi-Jie; Ying, Tian-Ping; Wang, Gang; Jin, Shi-Feng; Zhang, Han; Lin, Zhi-Ping; Chen, Xiao-Long

    2015-11-01

    Electrochemical method has been used to insert K/Na into FeSe lattice to prepare alkali-intercalated iron selenides at room temperature. Magnetization measurement reveals that KxFe2Se2 and NaxFe2Se2 are superconductive at 31 K and 46 K, respectively. This is the first successful report of obtaining metal-intercalated FeSe-based high-temperature superconductors using electrochemical method. It provides an effective route to synthesize metal-intercalated layered compounds for new superconductor exploration. Project supported by the National Natural Science Foundation of China (Grant Nos. 51322211and 91422303), the Strategic Priority Research Program (B) of the Chinese Academy of Sciences (Grant No. XDB07020100), Beijing Nova Program of China (Grant No. 2011096), and K. C. Wong Education Foundation, Hong Kong, China.

  13. Reclamation and Management of Saline and Alkali Soils

    DEFF Research Database (Denmark)

    Singh, Anoop; Katiyar, D.; Agrawal, S.B.

    2014-01-01

    Soil is the most precious natural resource and thus requires proper management. Estimates show that the world as a whole is losing at least 3.0 ha of arable land every minute due to salinization or sodification. In India about 7.0 M ha land is affected by salinity and alkalinity. The problem...... to combat with the problem. The present review is an attempt to emphasize the problem of salinity and alkalinity of soils, its effect on plants and application of physical, chemical and biological methods of soil reclamation along with management issues...... of saline and alkali soils is old but its magnitude and intensity have been increasing because of poor land and water management practices. The proper land management by way of its reclamation involves physical, chemical and biological means, which are site specific and their integration is highly desirable...

  14. The Effect of Radiation "Memory" in Alkali-Halide Crystals

    Science.gov (United States)

    Korovkin, M. V.; Sal'nikov, V. N.

    2017-01-01

    The exposure of the alkali-halide crystals to ionizing radiation leads to the destruction of their structure, the emergence of radiation defects, and the formation of the electron and hole color centers. Destruction of the color centers upon heating is accompanied by the crystal bleaching, luminescence, and radio-frequency electromagnetic emission (REME). After complete thermal bleaching of the crystal, radiation defects are not completely annealed, as the electrons and holes released from the color centers by heating leave charged and locally uncompensated defects. Clusters of these "pre centers" lead to electric microheterogeneity of the crystal, the formation of a quasi-electret state, and the emergence of micro-discharges accompanied by radio emission. The generation of REME associated with residual defectiveness, is a manifestation of the effect of radiation "memory" in dielectrics.

  15. Effect of Cross Linking Agent on Alkali/Surfactant/Polymer

    Institute of Scientific and Technical Information of China (English)

    ZHANG,Ke; LU,Xiang-Guo

    2008-01-01

    Alkali/surfactant/polymer (ASP) multisystem flooding technique, which has an expansive application prospect,is one of the enhancing oil recovery (EOR) methods. By adding the organic chromium to the ASP, the molecular structure of polymer was made to change, and the capability of controlling mobility coefficient of ASP was improved. The results showed that multisystem could still keep ultra-low interfacial tension between the multisystem and crude oil after addition of Cr3+. The resistance factor and residual resistance factor, the indicator which describes the capability of controlling mobility, upgraded strikingly. However its storage modulus and loss modulus,the indicator which describes viscoelasticity, increased. The results of physical simulation experiment indicated that this type of improved ASP could increase the recovery ratio by 4.3% compared to common ASP multisystem.

  16. Spectroscopic properties of alkali atoms embedded in Ar matrix.

    Science.gov (United States)

    Jacquet, E; Zanuttini, D; Douady, J; Giglio, E; Gervais, B

    2011-11-07

    We present a theoretical investigation of visible absorption and related luminescence of alkali atoms (Li, Na, and K) embedded in Ar matrix. We used a model based on core polarization pseudopotentials, which allows us to determine accurately the gas-to-matrix shifts of various trapping sites. The remarkable agreement between our calculated results and the experimental spectra recorded by several authors allows us to establish a clear assignment of the observed spectra, which are made of contributions from crystalline sites on the one hand, and of grain boundary sites on the other hand. Our study reveals remarkably large Stokes shifts, up to 9000 cm(-1), which could be observed experimentally to identify definitely the trapping sites.

  17. PYRAMIDAL-HOLLOW-BEAM DIPOLE TRAP FOR ALKALI ATOMS

    Institute of Scientific and Technical Information of China (English)

    YIN JIAN-PING; GAO WEI-JIAN; WANG YU-ZHU; ZHU YI-FU; WANG YI-QIU

    2000-01-01

    We propose a dark gravito-optical dipole trap, for alkali atoms, consisting of a blue-detuned, pyramidal-hollow laser beam propagating upward and the gravity field. When cold atoms from a magneto-optical trap are loaded into the pyramidal-hollow beam and bounce inside the pyramidal-hollow beam, they experience efficient Sisyphus cooling and geometric cooling induced by the pyramidal-hollow beam and the weak repumping beam propagating downward. Our study shows that an ultracold and dense atomic sample with an equilibrium 3D momentum of ~ 3hk and an atomic density above the point of Bose-Einstein condensation may be obtained in this pure optical trap.

  18. Inhibitory Effects of Mistletoe Alkali on Salivary Adenoid Cystic Carcinoma Cells

    Institute of Scientific and Technical Information of China (English)

    LI Mei-hua; WANG Yi-shu; ZHOU Hong-lan; LI Ya-juan; QIU Xin-ru; WANG Xue-yao; ZHAO Yu-yang

    2013-01-01

    Mistletoe alkali plays an important role in salivary adenoid cystic carcinoma(SACC) cell proliferation,apoptosis and invasion.Mistletoe alkali shows potent anticaner property.In this paper,immunocytochemical and immunofluorescence staining were employed to evaluate the expression levels of proliferating cell nuclear antigen(PCNA),Caspase 3,Caspase 8 and Caspase 9.Apoptosis was detected by acridine orange/ethidium bromide (AO/EB) staining,cell invasion ability was assessed by Boyden Chamber assay.Pretreatment with mistletoe alkali markedly decreased PCNA expression in SACC cells in a dose-dependent manner(P<0.001) and also led to increase the expression of Caspase 3,Caspase 8 and Caspase 9 in SACC cells compared with control group(P<0.001).Number of apoptotic cells increased dramatically in mistletoe alkali group(P<0.001).In Boyden Chamber assay,mistletoe alkali treatment could inhibit SACC cells to penetrate the artificial basement membrane compared with control group(P<0.01).Mistletoe alkali remarkably inhibited the proliferation and invasion of SACC cells and induced the apoptosis of SACC cells.These results provide an insight into the mechanisms of anticancer effects of mistletoe alkali,and highlight the potential clinical application of it.

  19. Alkali extraction and in vitro antioxidant activity of Monascus mycelium polysaccharides.

    Science.gov (United States)

    Wang, Pengrong; Chen, Danfeng; Jiang, Donghua; Dong, Xiameng; Chen, Panpan; Lin, Yaoxue

    2014-07-01

    In the present work, alkali extraction technology was used to optimize the extraction of Monascus mycelium polysaccharides for the first time. The extracting parameters of alkali extracted Monascus mycelium polysaccharides were optimized by Box-Behnken design (BBD). The optimum conditions were extraction temperature 49 °C, alkali concentration 7%, solvent/material ratio 23:1 (ml/g) and extraction time 2.3 h with an enhanced yield of 10.1%, compared with the yield 4.76% of hot water extraction, indicating that alkali extraction is a more efficient way. In order to discuss the biological activity of alkali extracted polysaccharides, we compared the in vitro antioxidant activity of alkali extracted polysaccharides (AMP) with hot water extracted polysaccharides (HMP). The result showed that AMP have the similar capability of scavenging both superoxide radical and 2, 2-diphenyl-1-picrylhydrazyl (DPPH) radical of HMP in vitro. Therefore, alkali extraction technology is not only a high-efficiency way to extract AMP, but also can retain the natural antioxidant activities of AMP, which can be used in pharmaceutical and food industries.

  20. Saline-alkali land in the Yellow River Delta:amelioration zonation based on GIS

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Soil salinization is one of the major land degradation types andhas greatly influenced sustainable agricultural development. Zonation of saline-alkali land is the precondition for effective amelioration. The present situation of saline-alkali land is monitored by remote sensing image processing. Causes for land salinization are analyzed, especially the two key factors, ground water depth and its mineralization degree, are analyzed by using long-term observation data. Previously,zonation of saline-alkali soil was made descriptively and artificially. Based on the present situation of saline-alkali land, ground water depth and ground water mineralization degree, the zonation of salinealkali land for amelioration in the Yellow River Delta was completed quantitatively. Four different ypes of saline-alkali land amelioration zones are delineated, namely, easy ameliorated zone,elatively difficult ameliorated zone, difficult ameliorated zone and unfavorable ameliorated zone.Countermeasures for ameliorating saline-alkali soils are put forward according to ecological conditions of different saline-alkali land zones.

  1. Effects of alkali and steaming on mechanical properties of snake fruit (Salacca) fiber

    Science.gov (United States)

    Darmanto, Seno; Rochardjo, Heru S. B.; Jamasri, Widyorini, Ragil

    2017-01-01

    The aim of this research is to investigate the effect of alkali treatment and steaming on mechanical properties of Snake Fruit frond fiber. The presence of surface impurities and a lot of hydroxyl groups makes natural fiber less compatible for composite materials reinforcement. Efforts to remove the impurities can be done by physical, chemical and mechanical treatments. This paper reports the treatment of Snake Fruit frond single fiber by subjecting it to alkali treatments with 2%- 8% NaOH for 2 - 6 hours at room temperature. The treatment is then followed by steaming at a pressure of 2 bars in 1 hour. Results show that the treatment of alkali and the alkali-steaming combination can increase cellulose percentage. The tensile tests show that this type of treatment in combination resulted in the higher tensile strength compared to untreated fiber. There is a significant increase in tensile strength with increasing alkali percentage. However, the further increase in the percentage of alkali solution will result in decreasing tensile strength. The highest value of tensile strength after treatment was 275 MPa with 6 hours treatment at alkali percentage of 2 %.

  2. Alkali-metal-supported bismuth polyhedra-principles and theoretical studies.

    Science.gov (United States)

    Monakhov, Kirill Yu; Linti, Gerald; Wolters, Lando P; Bickelhaupt, F Matthias

    2011-06-20

    We have quantum chemically investigated the structure, stability, and bonding mechanism in highly aggregated alkali-metal salts of bismuthanediide anions [RBi](2-) using relativistic density functional theory (DFT, at ZORA-BP86/TZ2P) in combination with a quantitative energy decomposition analysis (EDA). Our model systems are alkali-metal-supported bismuth polyhedra [(RBi)(n)M(2n-4)](4-) with unique interpenetrating shells of a bismuth polyhedron and an alkali-metal superpolyhedron. Furthermore, we have analyzed the trianionic inclusion complexes [M'@{(RBi)(n)M(2n-4)}](3-) involving an additional endohedral alkali-metal ion M'. The main objective is to assist the further development of synthetic approaches toward this class of compounds. Our analyses led to electron-counting rules relating, for example, the number of bonding orbitals (N(bond)) of the cage molecules [(RBi)(n)M(2n+Q)](Q) to the number of bismuth atoms (n(Bi)), alkali-metal atoms (n(M)), and net charge Q as N(bond) = n(Bi) + n(M) - Q (R = one-electron donor ligand; M = alkali metal; n = 4-12; Q = -4, -6, -8). Finally, on the basis of our findings, we predict the next members in the 5-fold symmetrical row of alkali-metallobismaspheres with a macroicosahedral arrangement.

  3. Origin of alkali rocks in the light of data on the fluid mantle flow

    Energy Technology Data Exchange (ETDEWEB)

    Kushev, V.G.; Mironov, A.G.

    1980-01-01

    The hypotheses on the alkali-basic melts as formed through partial fusion of either the hydroxyl-containing alkali peridotite (or pyroxenite), or the phlogopite- or amphibole-enriched rocks in the mantle turn out most relevant as for the alkali rock peculiarities. Still, the hypotheses do not explain the appearance of alkalies and water involved in fusion. It is supposed that the alkalies-enriched rocks result from the dynamometamorphic segregation of the mantle fluid (CH/sub 4/, H/sub 2/, CO), which reacts with the mantle rocks (magnetite+olivine+pyroxene) with subsequent release of H/sub 2/O and liberation of K and Na from the gaseous phase and pyroxenes lattice. The start of fusion is induced by sharp decrease of pressure and heat incoming along the deep dislocation zones in the mantle. Once produced, the alkali melt evolved through differetiation or interaction with enclosing rocks. This method provides interpretation of most petrological and geochemical peculiarities of different series of alkali rocks. 65 references.

  4. Radioluminescence of synthetic quartz related to alkali ions

    Energy Technology Data Exchange (ETDEWEB)

    Martini, M., E-mail: m.martini@unimib.it [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); INFN-Sezione di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Fasoli, M. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Galli, A. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Istituto di Fotonica e Nanostrutture, IFN-CNR (Italy); Villa, I. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Guibert, P. [IRAMAT-CRP2A (Institut de recherche sur les Archeomateriaux), UMR no. 5060, CNRS-Universite Bordeaux III, F-33607 Pessac (France)

    2012-04-15

    The radioluminescence (RL) of synthetic quartzes (GEMMA Quartz and Crystal Company) has been measured at room temperature. Some samples were treated by electrodiffusion ('sweeping') in order to change the concentrations of alkali ions, mainly Li{sup +} and Na{sup +}, which in quartz are known to be linked to Al ions, substitutional for Si ions. The RL emission spectra show evidence of a role of alkali ions in affecting some specific emissions. All the spectra could be analysed as composed of four bands in the blue and UV region. Specifically, the well known blue emission at around 470 nm was seen to be composed by two bands at 430 nm (2.86 eV) and at 485 nm (2.53 eV). Effects of irradiation, during the RL measurements, were clearly seen only in the 'Li swept in' sample, namely an increase in the 485 nm band intensity and a decrease in the 430 nm band one. The previously reported UV emission was detected at 355 nm (3.44 eV) in all the samples, being the most intense band in the 'swept out' sample. A further UV emission was detected at 315 nm (3.94 eV), more intense in untreated samples. Possible assignments of the detected emission bands are discussed in relation to the defects of quartz, specifically focusing on the Al centres that are most affected by sweeping procedures. - Highlights: Black-Right-Pointing-Pointer Contribution to the understanding of relationships between defects in quartz and luminescence emissions. Black-Right-Pointing-Pointer Role of charge compensators at substitutional Al sites in the optical properties of quartz. Black-Right-Pointing-Pointer Evidence of the double nature of the 'blue emission' (around 470 nm).

  5. The Structure and Thermodynamics of Alkali Halide Vapors.

    Science.gov (United States)

    Hartley, John George

    A comprehensive set of electron diffraction experiments were performed on 16 of the alkali halides in the vapor phase. A 40kev electron beam was scattered from the vapor effusing out of the nozzle of a temperature controlled gas cell. The resulting data were analyzed at the University of Edinburgh with the program ED80. This resulted in values for the bond lengths of monomers and the dimers, the bond angle of the dimers and the monomer-dimer ratios. In several cases, it was possible to further refine the data to obtain information on the mean amplitudes of vibration. As a check on the accuracy of the results, the monomer bond distances obtained by electron diffraction were compared to values obtained previously by microwave spectroscopy. The average monomer bond length r_{a} is corrected to obtain the equilibrium bond distance r_{e}. This value is then compared to the value of r_{e } obtained from microwave spectroscopy and found to be in excellent agreement. The bond lengths and angles of the dimers were compared against model calculations. While no one model was found to accurately predict the dimer structure parameters of all of the alkali halides, the Rittner model of Gowda et al was found to accurately predict the structure of six of the dimers. Thermodynamical calculations were performed on the model data which resulted in theoretical curves of the monomer-dimer ratios. Comparison of these curves with the experimental monomer-dimer ratio permits an evaluation of the model vibration frequencies. The enthalpy of formation of the dimer, Delta H_sp{2}{f}(298) is examined with regard to the size of the variation necessary to bring about agreement of the experimental and model monomer-dimer ratios.

  6. Quenching of excited alkali atoms and related effects in flames: Part II. Measurements and discussion

    NARCIS (Netherlands)

    Hooymayers, H.P.; Alkemade, C.T.J.

    1966-01-01

    An alternating current photoelectric device has been used for determining the yield factor p of resonance flourescence of the yellow sodium doublet and the infrared and blue potassium doublets in flames at atmospheric pressure as a function of the temperature and composition of the burnt flame gases

  7. Effect of alkali and heat treatments for bioactivity of TiO{sub 2} nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seo young, E-mail: mast6269@nate.com [Dept. of Dental Biomaterials and Institute of Bio degradable material, Institute of Oral Bioscience and BK21 plus project, School of Dentistry, Chonbuk National University, Jeonju, 561-756 (Korea, Republic of); Kim, Yu kyoung, E-mail: yk0830@naver.com [Dept. of Dental Biomaterials and Institute of Bio degradable material, Institute of Oral Bioscience and BK21 plus project, School of Dentistry, Chonbuk National University, Jeonju, 561-756 (Korea, Republic of); Park, Il song, E-mail: ilsong@jbnu.ac.kr [Division of Advanced Materials Engineering, Research Center for Advanced Materials Development and Institute of Biodegradable Materials, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Jin, Guang chun, E-mail: jingc88@126.com [Oral Medical College, Beihua University, Jilin City 132013 (China); Bae, Tae sung, E-mail: bts@jbnu.ac.kr [Dept. of Dental Biomaterials and Institute of Bio degradable material, Institute of Oral Bioscience and BK21 plus project, School of Dentistry, Chonbuk National University, Jeonju, 561-756 (Korea, Republic of); Lee, Min ho, E-mail: mh@jbnu.ac.kr [Dept. of Dental Biomaterials and Institute of Bio degradable material, Institute of Oral Bioscience and BK21 plus project, School of Dentistry, Chonbuk National University, Jeonju, 561-756 (Korea, Republic of)

    2014-12-01

    Highlights: • TiO{sub 2} nanotubes formed via anodization were treated by alkali and heat. • The surface roughness was increased after alkali treatment (p < 0.05). • After alkali and heat treatment, the wettability was better than before treatment. • Alkali treated TiO{sub 2} nanotubes were shown higher HAp formation in SBF. • Heat treatment affected on the attachment of cells for alkali treated nanotubes. - Abstract: In this study, for improving the bioactivity of titanium used as an implant material, alkali and heat treatments were carried out after formation of the nanotubes via anodization. Nanotubes with uniform length, diameter, and thickness were formed by anodization. The alkali and heat-treated TiO{sub 2} nanotubes were covered with the complex network structure, and the Na compound was generated on the surface of the specimens. In addition, after 5 and 10 days of immersion in the SBF, the crystallized OCP and HAp phase was significantly increased on the surface of the alkali-treated TiO{sub 2} nanotubes (PNA) and alkali and heat-treated TiO{sub 2} nanotubes (PNAH) groups. Cell proliferation was decreased due to the formation of amorphous sodium titanate (Na{sub 2}TiO{sub 3}) layer on the surface of the PNA group. However, anatase and crystalline sodium titanate were formed on the surface of the PNAH group after heat treatment at 550 °C, and cell proliferation was improved. Thus, PNA group had higher HAp forming ability in the simulated body fluid. Additional heat treatment affected on enhancement of the bioactivity and the attachment of osteoblasts for PNA group.

  8. Use of precalciners to remove alkali from raw materials in the cement industry. Final report, July 1978-July 1980

    Energy Technology Data Exchange (ETDEWEB)

    Gartner, E.M.

    1980-07-01

    The objective of this work was to develop an efficient means of removing alkali metal compounds (alkalies) from high-alkali aluminosilicate raw materials of the type commonly used as part of cement raw mixes in order to increase the energy efficiency of cement manufacture. The intention of this project was to determine whether the high-alkali raw materials could be pyroprocessed separately to remove the alkalies before they entered the rotary kiln, where they would be mixed with the other raw feed components. If this could be achieved, considerable savings could be made in the energy required to remove alkalies, compared to conventional methods in which the cement raw mix must be treated as a whole. Two different methods of alkali removal were examined, namely, vaporization of alkalies at relatively low temperatures; and alkali-rich melt separation at relativey high temperatures. The results showed that the removal of alkalies by pyroprocessing of high-alkali raw feed components separate from the other cement raw mix components is not likely to be a practical alternative to the best available conventional precalciner technology. (LCL)

  9. Trace Element Geochemistry of Hannuoba Ultramafic Inclusion—bearing Alkali Basalts

    Institute of Scientific and Technical Information of China (English)

    支霞臣

    1990-01-01

    Presented in this paper are the trace element abundances of 16 samples of Hannuoba ultramafic inclusion-bearing aldali basalts,which were determined by instrumental neutron activation analysis and X-ray fluorescence spectrometry.The Petrogenesis of the alkali basalt suite has been modeled by batch partial melting and and Rayleigh fractional crystallization processes,The geochemical characteristics of the mantle source from where alkali basalts were derived are described in terms of variations in trace element abundances of the alkali basalt suite.

  10. Effect of Alkali Treatment on the Structure and Catalytic Properties of ZSM-5 Zeolite

    Institute of Scientific and Technical Information of China (English)

    Zi Yun LI; Xin SUN; Qiang XIAO; Shou He XIANG

    2005-01-01

    Catalytic properties of ZSM-5 zeolite samples pretreated with NaOH solution have been investigated. The samples are characterized by XRD, SEM, chemical analysis, and N2 adsorption.The results indicate that mesopores are created in ZSM-5 crystals under alkali treatment without change the microporous structure and acidic strength of the zeolite, but the crystallinity is greatly decreased under severe treatment. IR indicates that the concentration of silanol is greatly enriched by alkali treatment. The etherification activities of ZSM-5 zeolites are greatly increased by alkali-treatment. The noticeably improved catalytic activity of treated samples is ascribed to the formation of mesopores and greatly enriched silanol group.

  11. Pretreatment of garden biomass by alkali-assisted ultrasonication: effects on enzymatic hydrolysis and ultrastructural changes

    OpenAIRE

    Gabhane, Jagdish; William, SPM Prince; Vaidya, Atul Narayan; Anand, Duraisamy; Wate, Satish

    2014-01-01

    The present investigation aims at studying the effectiveness of alkali-assisted ultrasonication on pretreatment of garden biomass (GB). Dry and powdered GB suspended in 1% NaOH was ultrasonicated for 15, 30 and 60 minutes at a frequency of 25 KHZ. The mode of action and effectiveness of alkali-assisted ultrasonication on GB was established through microscopic, scanning electron microscopic and X-ray diffraction studies. A perusal of results showed that alkali-assisted ultrasonication led to f...

  12. Alkali extraction and in vitro antioxidant activity of Monascus mycelium polysaccharides

    OpenAIRE

    Wang, Pengrong; Chen, Danfeng; Jiang, Donghua; Dong, Xiameng; Chen, Panpan; Lin, Yaoxue

    2012-01-01

    In the present work, alkali extraction technology was used to optimize the extraction of Monascus mycelium polysaccharides for the first time. The extracting parameters of alkali extracted Monascus mycelium polysaccharides were optimized by Box-Behnken design (BBD). The optimum conditions were extraction temperature 49 °C, alkali concentration 7%, solvent/material ratio 23:1 (ml/g) and extraction time 2.3 h with an enhanced yield of 10.1%, compared with the yield 4.76% of hot water extraction...

  13. Triiodide and mixed tri-halide anions from negative ion electrospray ionization of alkali halide solutions

    Science.gov (United States)

    Shukla, Anil

    2017-10-01

    Electrospray ionization of alkali halide solutions in the negative ion mode results in the formation of cluster ions of the general formula, (MX)nX-. However, alkali iodides form triiodide anion, I3-, in high abundance in addition to cluster ions. Br3- ions are observed in low abundance. Also, mixed tri-halide anions, I2Y-, are observed in high abundance when a small amount (<1%) of KI is added to other alkali halide solutions. These results are explained by the uniquely different physical characteristics of lithium and the iodide ions compared with others in the series.

  14. Communication: Dopant-induced solvation of alkalis in liquid helium nanodroplets

    Science.gov (United States)

    Renzler, Michael; Daxner, Matthias; Kranabetter, Lorenz; Kaiser, Alexander; Hauser, Andreas W.; Ernst, Wolfgang E.; Lindinger, Albrecht; Zillich, Robert; Scheier, Paul; Ellis, Andrew M.

    2016-11-01

    Alkali metal atoms and small alkali clusters are classic heliophobes and when in contact with liquid helium they reside in a dimple on the surface. Here we show that alkalis can be induced to submerge into liquid helium when a highly polarizable co-solute, C60, is added to a helium nanodroplet. Evidence is presented that shows that all sodium clusters, and probably single Na atoms, enter the helium droplet in the presence of C60. Even clusters of cesium, an extreme heliophobe, dissolve in liquid helium when C60 is added. The sole exception is atomic Cs, which remains at the surface.

  15. Field emission properties of capped carbon nanotubes doped by alkali metals:a theoretical investigation

    Institute of Scientific and Technical Information of China (English)

    Jin Lei; Fu Hong-Gang; Xie Ying; Yu Hai-Tao

    2012-01-01

    The electronic structures and field emission properties of capped CNT55 systems with or without alkali metal atom adsorption were systematically investigated by density functional theory calculation.The results indicate that the adsorption of alkali metal on the center site of a CNT tip is energetically favorable.In addition,the adsorption energies increase with the introduction of the electric field.The excessive negative charges on CNT tips make electron emittance much easier and result in a decrease in work function.Furthermore,the inducing effect by positively charged alkali metal atoms can be reasonably considered as the dominant reason for the improvement in field emission properties.

  16. Evaluate on utilization of feldspar in Henan Nanzhao%河南南召低品位长石矿可利用性评价研究

    Institute of Scientific and Technical Information of China (English)

    郝小非; 李珍; 张成强; 胡宏杰

    2015-01-01

    以河南南召某低品位长石矿为研究对象,根据矿石的化学多项分析、工艺矿物学研究和X衍射分析,查明了物质组成和赋存状态。试验结果表明:采用简单的工艺流程,通过磨矿、脱泥、差异分选、磁选,可使原矿中Fe2 O3含量0.83%降到0.20%,同时获得的精矿产率为83.9%。并用该长石精矿制备了饰面用微晶玻璃板,当长石精矿占基础玻璃质量的40%时,制备的制品硬度为6.5,弯曲强度105.2M Pa ,吸水率为0,指标优于人造大理岩,为低品位长石开发利用提供了新的利用途径。%Taking a low grade of Feldspar from Henan Province as the object of study .According to chemical analysis ,X‐diffraction analysis ,and research of process mineralogy ,It is identified the ore composition and occurrence states .This paper uses simple process ,appropriate size of ground product , desliming‐granularity ,magnetic intensity .Succeeds in separating effectively iron‐oxide grade 0 .83% sample . by grinding ,desliming ,the differences separation ,magnetic separation ,get concentrate iron‐oxide grade 0 . 20% ,productivity 83 .9% .Glass ceramics used for veneer are prepared ,by making use of the concentrate . When it adds 40% ,The hardness of products are 6 .5 ,flexural strength are 105 .2MPa .It is better than Artificial marble .It provides a new way to develop this type of feldspar .

  17. Fluid Composititon and Carbon & Oxygen Isotope Geochemistry of Cenozoic Alkali Basalts in Eastern China

    Institute of Scientific and Technical Information of China (English)

    张铭杰; 王先彬; 等

    1999-01-01

    The fluid compositions of Cenozoic alkali basalts in eastern China have been determined by the pyrolysis-MS method,meanwhile the carbon and oxygen isotopic compositions of CO2 released from these samples at different heating temperatures have been analyzed by the vacuum step-heating method.The data show the volatiole heterogeneity in upper-mantle sources and different evolution trends of alkali basaltic magmas in eastern China,and these alkali basaltic magmas may be generated in the oxidizing milieu,as compared with mantle-derived xenoliths in these alkali basalts,and exotic volatile components were mixed into these magmas in the process of their formation and development.

  18. Use of Fly Ash in the Mitigation of Alkali-Silica Reaction in Concrete

    Science.gov (United States)

    2010-11-12

    crystallinity of the silica and its solubility. Common reactive minerals susceptible to ASR include strained quartz, cristobalite , opal, obsidian, chert, and...residues, whereas alkali-silica reactive components include opal, cristobalite , tridymite, siliceous and some intermediate volcanic glass, chert

  19. Enhancement of tensile strength of lignocellulosic jute fibers by alkali-steam treatment.

    Science.gov (United States)

    Saha, Prosenjit; Manna, Suvendu; Chowdhury, Sougata Roy; Sen, Ramkrishna; Roy, Debasis; Adhikari, Basudam

    2010-05-01

    The physico-chemical properties of jute fibers treated with alkali (NaOH) solution have been investigated in this study. The treatments were applied under ambient and elevated temperatures and high pressure steaming conditions. To the knowledge of these authors the influence of alkali-steam treatment on the uniaxial tensile strength of natural ligno-cellulosic fibers, such as jute, has not been investigated earlier. The results from this investigation indicate that a 30 min dipping of the fibers in 0.5% alkali solution followed by 30 min alkali-steam treatment leads to an increase in the tensile strength of up to 65%. The increase appears to be due to fiber separation and removal of non-cellulosic materials, which, in turn, resulted in an increased crystallinity.

  20. The ecology and genetics of alkali bulrush (Schoenoplectus maritimus) : Management implications

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Alkali bulrush (Schoenoplectus maritimus) is an important wetland plant species, in the Intermountain West. However, there is a lack of knowledge on how best to...

  1. Experimental and Theoretical Studies of Pressure Broadened Alkali-Metal Atom Resonance Lines

    Science.gov (United States)

    Shindo, F.; Zhu, C.; Kirby, K.; Babb, J. F.

    2006-01-01

    We are carrying out a joint theoretical and experimental research program to study the broadening of alkali atom resonance lines due to collisions with helium and molecular hydrogen for applications to spectroscopic studies of brown dwarfs and extrasolar giant planets.

  2. Is electronegativity a useful descriptor for the pseudo-alkali metal NH4?

    Science.gov (United States)

    Whiteside, Alexander; Xantheas, Sotiris S; Gutowski, Maciej

    2011-11-18

    Molecular ions in the form of "pseudo-atoms" are common structural motifs in chemistry, with properties that are transferrable between different compounds. We have determined one such property--the electronegativity--for the "pseudo-alkali metal" ammonium (NH(4)), and evaluated its reliability as a descriptor versus the electronegativities of the alkali metals. The computed properties of ammonium's binary complexes with astatine and of selected borohydrides confirm the similarity of NH(4) to the alkali metal atoms, although the electronegativity of NH(4) is relatively large in comparison to its cationic radius. We have paid particular attention to the molecular properties of ammonium (angular anisotropy, geometric relaxation and reactivity), which can cause deviations from the behaviour expected of a conceptual "true alkali metal" with this electronegativity. These deviations allow for the discrimination of effects associated with the molecular nature of NH(4).

  3. Studies of Alkali Sorption Kinetics for Pressurized Fluidized Bed Combustion by High Pressure Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, K.J.; Willenborg, W.; Fricke, C.; Prikhodovsky, A.; Hilpert, K.; Singheiser, L.

    2002-09-20

    This work describes the first approach to use High Pressure Mass Spectrometry (HPMS) for the quantification and analysis of alkali species in a gas stream downstream a sorbent bed of different tested alumosilicates.

  4. Improvement of a polarized alkali ion source by means of optical pumping

    Energy Technology Data Exchange (ETDEWEB)

    Dreves, W.; Koch, E.; Jaensch, H.; Kamke, W.; Broermann, W.; Fick, D.

    1982-01-01

    A source for polarized alkali ions can be improved considerably by optical pumping of the atom beam in combination with a modified weak field transition. M-level populations were investigated using laser induced fluorescence in a magnetic field.

  5. Evaluation of thermobarometry for spinel lherzolite fragments in alkali basalts

    Science.gov (United States)

    Ozawa, Kazuhito; Youbi, Nasrrddine; Boumehdi, Moulay Ahmed; McKenzie, Dan; Nagahara, Hiroko

    2017-04-01

    Geothermobarometry of solid fragments in kimberlite and alkali basalts, generally called "xenoliths", provides information on thermal and chemical structure of lithospheric and asthenospheric mantle, based on which various chemical, thermal, and rheological models of lithosphere have been constructed (e.g., Griffin et al., 2003; McKenzie et al., 2005; Ave Lallemant et al., 1980). Geothermobarometry for spinel-bearing peridotite fragments, which are frequently sampled from Phanerozoic provinces in various tectonic environments (Nixon and Davies, 1987), has essential difficulties, and it is usually believed that appropriated barometers do not exist for them (O'Reilly et al., 1997; Medaris et al., 1999). Ozawa et al. (2016; EGU) proposed a method of geothermobarometry for spinel lherzolite fragments. They applied the method to mantle fragments in alkali basalts from Bou Ibalhatene maars in the Middle Atlas in Morocco (Raffone et al. 2009; El Azzouzi et al., 2010; Witting et al., 2010; El Messbahi et al., 2015). Ozawa et al. (2016) obtained 0.5GPa pressure difference (1.5-2.0GPa) for 100°C variation in temperatures (950-1050°C). However, it is imperative to verify the results on the basis of completely independent data. There are three types of independent information: (1) time scale of solid fragment extraction, which may be provided by kinetics of reactions induced by heating and/or decompression during their entrapment in the host magma and transportation to the Earth's surface (Smith, 1999), (2) depth of the host basalt formation, which may be provided by the petrological and geochemical studies of the host basalts, and (3) lithosphere-asthenosphere boundary depths, which may be estimated by geophysical observations. Among which, (3) is shown to be consistent with the result in Ozawa et al. (2016). We here present that the estimated thermal structure just before the fragment extraction is fully supported by the information of (1) and (2). Spera (1984) reviewed

  6. A contribution to the surface characterization of alkali metal sulfates

    Energy Technology Data Exchange (ETDEWEB)

    Fantauzzi, Marzia; Rigoldi, Americo; Elsener, Bernhard; Atzei, Davide; Rossi, Antonella, E-mail: rossi@unica.it

    2014-03-01

    Highlights: • Full electronic characterization of alkali metals sulfates by X-ray photoelectron spectroscopy and X-ray induced Auger electron spectroscopy. • Curve-fitting of SKLL signals makes possible to clarify the role of the cation in the series of alkali metal sulfates. • Differences in the binding energies and Auger parameter are discussed in terms of the electronic properties and the polarizability of the cation. • The line intensities are analyzed and a thorough quantitative analysis is presented. - Abstract: The analytical characterization of surfaces of sulfur-bearing samples that present sulfides, polysulfides and/or elemental sulfur as reaction products can be difficult by simply relying on the binding energy of the S2p X-ray photoelectron signals, due to the small chemical shifts. In such cases the Auger parameter concept can be used to distinguish among different chemical states, but this requires a model to curve fit complex Auger SKLL signals in order to resolve the contributions arising from sulfur in different chemical states on the surface. With this scope a detailed X-ray photoelectron spectroscopy (XPS) and X-ray induced Auger electron spectroscopy (XAES) surface analytical study of the group IA sulfates is presented in this paper. Sulfates were chosen as model compounds for curve fitting the X-ray induced SKLL spectra since in these compounds sulfur is present in a unique chemical state. For the first time the multicomponent SKLL spectra are fitted with model functions consisting of an intense {sup 1}D and a low intensity {sup 1}S contribution with constant energy difference of 8 eV. It was found that the kinetic energy of the SK{sub 2,3}L{sub 2,3} ({sup 1}D) line increases from 2105.1 ± 0.1 to 2107.5 ± 0.2 eV whereas the corresponding S2p{sub 3/2} binding energy decreases from 169.5 ± 0.1 eV for Li{sub 2}SO{sub 4} to 167.8 ± 0.1 eV for Cs{sub 2}SO{sub 4}. Shifts to lower binding energy values are observed also for S2p, S2s and O1

  7. Alkali Basalts From the Galatia Volcanic Complex, NW Central Anatolia, Turkey

    OpenAIRE

    Tankut, Ayla; GÜLEÇ, Nilgün

    2014-01-01

    Alkali basalts occur as small lava flows associated with the andesitic lava flows and pyroclastics of Early to Middle Miocene age which are the main constituents of the Galatia volcanic complex. The northern margin of the complex is bordered by the North Anatolian Fault wher eas the southern margin is surrounded by a continental sedimentary sequence which interfingers with the volcanics. New K-Ar age determinations of the basalts reveal that alkali basalts erupted at two differ ent periods ...

  8. Alkali Metal-incorporated Mesoporous Smectites:Crystallinity and Textural Properties

    Institute of Scientific and Technical Information of China (English)

    HE Yan-feng; Shinichiro Fujita; Nobuhiro Iwasa; Bhalchandra M. Bhanage; Masahiko Arai

    2003-01-01

    A series of mesoporous smectite-like materials incorporated with alkali metals such as Li, Na, K and Cs has been synthesized with the hydrothermal method. The crystalline and the pore structures of the materials synthesized significantly change with the introduction of alkali metals. The addition of Li gives highly ordered layer phases, while the incorporation of Cs yields much less crystalline structures. Although Na or K has little effect on the crystalline structure, they modify the pore structure.

  9. The Feasibility of ASP Flooding with Low Alkali Concentration in Heterogeneous Reservoirs

    Institute of Scientific and Technical Information of China (English)

    HouJirui; ZhangShufen; YangJinzong; YueXiang'an

    2005-01-01

    In this paper, as far as the ASP flooding in the pilot area of Daqing oilfield is concerned, the effect of apparent viscosity of ASP solution on enhanced oil recovery have been studied by comparison of experiments on artificial heterogeneous cores with on natural cores.The results showed that the decrease in the concentration of alkali could increase tile apparent viscosity of ASP solutions, namely, the apparent viscosity increased and the IFF couldn't get ultra low, and the oil recovery efficiency by ASP solution with a reasonably lower concentration of alkali was not less than that with a higher concentration of alkali and ultra low IFF. The experiments with models having impermeable interlayers between adjacent layers, and by means of “co-injection and separate production” showed that the ASP solution with a higher viscosity and a lower alkali concentration was more beneficial to starting-up medium and low permeability layers and enhancing total oil recovery. Therefore, to heterogeneous reservoir, as factors of affecting oil recovery, the apparent viscosity may be more important than the ultralow IFF. Furthermore, on the premise that the concentration of surfactant and the concentration of polymer keep constant, ASP flooding with low alkali concentration not only enlarges the selectable range of surfactants and decreases the cost of ASP flooding, but also solves the problem of alkali scales. Finally, a dynamic absorption experiment was performed with a 0.5 meter long linked-up natural core to determine alkali wastage in formation. The result being accord with the application case in the pilot confirmed that it was not necessary to add the alkali too much in ASP flooding from a new direction.

  10. Properties of Hydrated Alkali Metals Aimed at the Ion Channel Selectivity

    Institute of Scientific and Technical Information of China (English)

    AN Hai-Long; LIU Yu-Zhi; ZHANG Su-Hua; ZHAN Yong; ZHANG Hai-Lin

    2008-01-01

    The hydration structure properties of different alkali metal ions with eight water molecules and potassium ions with different numbers of water molecules are studied using the mixed density functional theory, B3LYP, with 6-311G basis set. The hydration structures are obtained from structure optimization and the optimum numbers of water molecules in the innermost hydration shell for the alkali metal ions are found. Some useful information about the ion channel selectivity is presented.

  11. Calculated Pressure Induced BCC-FCC Phase Transitions in Alkali Metals

    OpenAIRE

    DAĞISTANLI, Hamdi; MUTLU, R. Haluk

    2008-01-01

    The partial occupation numbers and density of states (DOS), and the total DOS at the Fermi level are calculated as a function of reduced atomic volume for bcc and fcc alkali metals employing the linear-muffin-tin-orbital (LMTO) method. By means of the abrupt changes obtained in the partial and total DOS values at the Fermi level, good agreement with regard to experiment were found in predicting the bcc-fcc transition volumes of the alkali metals.

  12. Thermochemical Ablation Therapy of VX2 Tumor Using a Permeable Oil-Packed Liquid Alkali Metal

    OpenAIRE

    2015-01-01

    Objective Alkali metal appears to be a promising tool in thermochemical ablation, but, it requires additional data on safety is required. The objective of this study was to explore the effectiveness of permeable oil-packed liquid alkali metal in the thermochemical ablation of tumors. Methods Permeable oil-packed sodium–potassium (NaK) was prepared using ultrasonic mixing of different ratios of metal to oil. The thermal effect of the mixture during ablation of muscle tissue ex vivo was evaluat...

  13. Impact of Alkali Pretreatment on the Chemical Component Distribution and Ultrastructure of Poplar Cell Walls

    OpenAIRE

    Zhe Ji; Zhe Ling; Xun Zhang; Gui-Hua Yang; Feng Xu

    2014-01-01

    Alkali pretreatment is one of the leading pretreatment technologies for biofuel applications. The histochemical and structural characteristics of poplar cell walls were investigated before and after sodium hydroxide pretreatment (121 oC, 2%) to understand the alterations in biomass cellular structure, which were correlated with saccharification yield. Results showed that alkali pretreatment preferentially removed lignin from the S2 of fibers, which was similar to the behaviors of coniferyl al...

  14. Impact of alkali salts on the kinetics and microstructural development of cementitious systems

    OpenAIRE

    Mota Gassó, Berta

    2015-01-01

    Supplementary cementitious materials (SCM) lower the environmental impact of cement and concrete but react more slowly than Portland cement, which therefore limits the levels of substitution possible as reasonable early strengths are necessary. One of the main factors affecting the reaction of the SCMs is the alkalinity of the pore solution. However, alkalis do not only affect SCMs, but also the clinker phases. It is generally accepted that alkalis accelerate the hydration of Portland cement ...

  15. Cold three-body collisions in hydrogen-hydrogen-alkali atomic system

    CERN Document Server

    Wang, Yujun; Esry, B D

    2010-01-01

    We have studied hydrogen-hydrogen-alkali three-body systems in the adiabatic hyperspherical representation. For the spin-stretched case, there exists a single $X$H molecular state when $X$ is one of the bosonic alkali atoms: $^7$Li, $^{23}$Na, $^{39}$K, $^{87}$Rb and $^{133}$Cs. As a result, the {\\em only} recombination process is the one that leads to formation of $X$H molecules, H+H+$X

  16. Endoscopic pyloroplasty for severe gastric outlet obstruction due to alkali ingestion in a child

    OpenAIRE

    Dehghani, Seyed Mohsen; Aldaghi, Mitra; Javaherizadeh, Hazhir

    2016-01-01

    A common belief is that alkali ingestion causes severe esophageal damage and limited gastric injury due to the buffering action of acid. Gastric injury has been observed in patients who ingested alkali. Gastric outlet obstruction (GOO) secondary to caustic ingestion occurs due to fibrosis after resolution of the acute injury and inflammation, most commonly 6 to 12 weeks after initial ingestion. The traditional treatment for GOO related to ingestion of corrosive agents is surgery. Experience w...

  17. "Textbook" adsorption at "nontextbook" adsorption sites: Halogen atoms on alkali halide surfaces

    OpenAIRE

    Li, B.; Michaelides, A.; Scheffler, M.

    2006-01-01

    Density-functional theory (DFT) and second order Møller-Plesset perturbation theory calculations indicate that halogen atoms bond preferentially to halide substrate atoms on a series of alkali halide surfaces, rather than to the alkali atoms as might be anticipated. An analysis of the electronic structures in each system reveals that this novel adsorption mode is stabilized by the formation of textbook two-center three-electron covalent bonds. The implications of these findings to, for exampl...

  18. Development of alkali activated cements and concrete mixture design with high volumes of red mud

    OpenAIRE

    KRIVENKO PAVEL; O. Kovalchuk; PASKO ANTON; CROYMANS TOM; HULT MIKAEL; LUTTER GUILLAUME; VANDEVENNE N.; SCHREURS S.; Schroeyers, W.

    2017-01-01

    Dedicated cement compositions were formulated to enable the incorporation of large volume fractions of red mud in alkali activated cements, taking into account the role of the aluminosilicate phase in the processes of hydration and hardening. High volume red mud alkali activated cements were synthesized using a proper combination of red mud, low basic aluminosilicate compounds with a glass phase (blast-furnace slag) and additives selected from high-basic Ca-containing cements with a crystalli...

  19. ACCUMULATION OF ALKALIS IN THE RECYCLING FILTRATE OF THE PHOSPHOGYPSUM PULPS

    OpenAIRE

    ANTANAS KAZILIUNAS; MARYTE BACAUSKIENE

    2011-01-01

    Sodium and potassium combinations existing in phosphogypsum are highly soluble and remain in the filtrate, their amount increasing with each recycle. It has been determined that the amount of alkalis in the recycling filtrate depends on an amount of alkalis in uncleaned phosphogypsum, a number of recycles in the filtrate, the technology of the phosphogypsum pulp preparation and an amount of soluble phosphates. New phosphate formations composed in an acid medium (pH = 4.5-5) are well crystaliz...

  20. Geochronology of Ailaoshan-Jinshajiang alkali- rich intrusive rocks and their Sr and Nd isotopic characteristics

    Institute of Scientific and Technical Information of China (English)

    张玉泉; 谢应雯

    1997-01-01

    Twenty-nine isotopic ages, ranging from 41 to 27 Ma, are presented for the alkali-rich intrusive rocks and their coexisting alkaline volcanic rocks, lamprophyres and acidic porphyries, indicating that they are Tertiary in age. The alkali-rich intrusive rocks have 143Nd/144Nd ratios from 0. 512 415 to 0. 512 544, and 87Sr/86Sr ratios from 0.705 4 to 0.706 8, suggesting that their material originates from an enriched mantle source.