Development of an efficient grain refiner for Al-7Si alloy and its modification with strontium

Energy Technology Data Exchange (ETDEWEB)

Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

2000-05-15

The grain refining response of Al and Al-7Si alloy has been studied with various Al-Ti, Al-B and Al-Ti-B master alloys at different addition levels. The results show that Al-B and B rich Al-Ti-B master alloys cannot grain refine Al, while they are efficient grain refiners to Al-7Si alloy. The level of grain refinement saturates after 0.03% of Ti or B for most of the master alloys studied both at short and long holding times. The grain refining efficiency of some elements other than Ti and B on Al-7Si alloy has also been studied. Interestingly, all the elements studied (B, Cr, Fe, Mg, Ni, Ti and Zr) have resulted in some grain refinement of Al-7Si alloy at short holding time and have shown fading/poisoning on long holding, which increased in the order of B (no poisoning), Ti, Cr, Ni, Fe, Mg, Zr. Sr (0.02%) has been found to provide complete modification of the eutectic in Al-7Si alloy within 2 min, which is not lost even after long holding up to 120 min. Significant improvements in the mechanical properties have been obtained by a combination of grain refinement and modification to an extent that was not possible by either of them alone. (orig.)

Effect of electric pulse modification on mircostructure and properties of Ni-rich Al-Si piston alloy

Directory of Open Access Journals (Sweden)

Bing Wang

2016-03-01

Full Text Available In order to improve the properties of Ni-rich (2.5wt.% Al-Si piston alloy, electric pulse modification was applied in fabricating the Ni-rich Al-Si piston alloy in this study. The effect of electric pulse modification on the mechanical properties of the Ni-rich Al-Si piston alloy was studied using optical microscope (OM, scanning electron microscope (SEM, X-ray diffraction (XRD, microhardness measurement and tensile strength testing. The results showed that the microstructures of Ni-rich Al-Si piston alloy treated by electric pulse modification were refined, the solid solubility of Cu, Ni, Si, etc. in α-Al matrix was improved, and furthermore, the microhardness and high-temperature tensile strength were increased by 9.41% and 17.5%, respectively. The distribution of second phases was also more uniform compared with that of a non-modified sample.

THE APPLICATION OF Ni FOR IMPROVEMENT OF Al-Si-Fe ALLOYS

Directory of Open Access Journals (Sweden)

Jozef Petrík

2009-09-01

Full Text Available Iron, often present in secondary material (scrap forms brittle and hard needles in Al-Si alloys.These particles decrease the mechanical properties of castings. A reliable and economic method of iron elimination from aluminium alloys has not been well-known yet in metallurgical practice. The influence of nickel as an iron corrector (up to 0.7 % and iron (up to 2.5 % on the fluidity, microstructure and mechanical properties of the Al alloy with 9.75 % Si, 0.2 % Mg was evaluated. The presence of Ni results in shortening of the needles, but the segmentation of ß needles was not observed. Improvement of mechanical properties was observed despite of low affecting of microstructure.

The Ce-Ni-Si system as a representative of the rare earth-Ni-Si family: Isothermal section and new rare-earth nickel silicides

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Knotko, A.V.; Garshev, A.V. [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Faculty of Materials Science, Moscow State University, Leninskie Gory, House 1, Building 73, Moscow, GSP-1, 119991 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Geological Faculty Moscow State University, Leninskie Gory, Moscow 119991 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal, 59082-970 (Brazil)

2016-11-15

The Ce-Ni-Si system has been investigated at 870/1070 K by X-ray and microprobe analyses. The existence of the known compounds, i.e.: Ce{sub 2}Ni{sub 15.8}Si{sub 1.2} (Th{sub 2}Ni{sub 17}-type), Ce{sub 2}Ni{sub 15-14}Si{sub 2-3} (Th{sub 2}Zn{sub 17}-type), CeNi{sub 8.6}Si{sub 2.4} (BaCd{sub 11}-type), CeNi{sub 8.8}Si{sub 4.2} (LaCo{sub 9}Si{sub 4}-type), CeNi{sub 6}Si{sub 6} (CeNi{sub 6}Si{sub 6}-type), CeNi{sub 5}Si{sub 1-0.3} (TbCu{sub 7}-type), CeNi{sub 4}Si (YNi{sub 4}Si-type), CeNi{sub 2}Si{sub 2} (CeGa{sub 2}Al{sub 2}-type), Ce{sub 2}Ni{sub 3}Si{sub 5} (U{sub 2}Co{sub 3}Si{sub 5}-type), Ce{sub 3}Ni{sub 6}Si{sub 2} (Ce{sub 3}Ni{sub 6}Si{sub 2}-type), Ce{sub 3}Ni{sub 4}Si{sub 4} (U{sub 3}Ni{sub 4}Si{sub 4}-type), CeNiSi{sub 2} (CeNiSi{sub 2}-type), ~CeNi{sub 1.3}Si{sub 0.7} (unknown type structure), Ce{sub 6}Ni{sub 7}Si{sub 4} (Pr{sub 6}Ni{sub 7}Si{sub 4}-type), CeNiSi (LaPtSi-type), CeNi{sub 0.8-0.3}Si{sub 1.2-1.7} (AlB{sub 2}-type), ~Ce{sub 2}Ni{sub 2}Si (unknown type structure), ~Ce{sub 4.5}Ni{sub 3.5}Si{sub 2} (unknown type structure), Ce{sub 15}Ni{sub 7}Si{sub 10} (Pr{sub 15}Ni{sub 7}Si{sub 10}-type), Ce{sub 5}Ni{sub 1.85}Si{sub 3} (Ce{sub 5}Ni{sub 1.85}Si{sub 3}-type), Ce{sub 6}Ni{sub 1.4}Si{sub 3.4} (Ce{sub 6}Ni{sub 1.67}Si{sub 3}-type), Ce{sub 7}Ni{sub 2}Si{sub 5} (Ce{sub 7}Ni{sub 2}Si{sub 5}-type) and Ce{sub 3}NiSi{sub 3} (Y{sub 3}NiSi{sub 3}-type) has been confirmed in this section. Moreover, the type structure has been determined for ~Ce{sub 2}Ni{sub 2}Si (Mo{sub 2}NiB{sub 2}-type Ce{sub 2}Ni{sub 2.5}Si{sub 0.5}) and ~Ce{sub 4.5}Ni{sub 3.5}Si{sub 2} (W{sub 3}CoB{sub 3}-type Ce{sub 3}Ni{sub 3-2.7}Si{sub 1-1.3}) and new ternary phases Ce{sub 2}Ni{sub 6.25}Si{sub 0.75} (Gd{sub 2}Co{sub 7}-type), CeNi{sub 7-7.6}Si{sub 6-5.4} (GdNi{sub 7}Si{sub 6}-type) and ~Ce{sub 27}Ni{sub 42}Si{sub 31} (unknown type structure) have been identified in this system. Quasi-binary phases, solid solutions, were detected at 870/1070 K for CeNi{sub 5}, CeNi{sub 3} and CeSi

Thermal stability of Ni/Ti/Al ohmic contacts to p-type 4H-SiC

Energy Technology Data Exchange (ETDEWEB)

Yu, Hailong; Shen, Huajun, E-mail: shenhuajun@ime.ac.cn; Tang, Yidan; Bai, Yun; Liu, Xinyu [Microwave Device and IC Department, Institute of Microelectronics of Chinese Academy of Sciences, Beijing 100029 (China); Zhang, Xufang [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Wu, Yudong; Liu, Kean [Zhuzhou CSR Times Electric Co., Ltd, ZhuZhou 412001 (China)

2015-01-14

Low resistivity Ni/Ti/Al ohmic contacts on p-type 4H-SiC epilayer were developed, and their thermal stabilities were also experimentally investigated through high temperature storage at 600 °C for 100 h. The contact resistance of the Al/Ti/Ni/SiC contacts degraded in different degrees, and the contact morphology deteriorated with the increases of the average surface roughness and interface voids. X-ray spectra showed that Ni{sub 2}Si and Ti{sub 3}SiC{sub 2}, which were formed during ohmic contact annealing and contributed to low contact resistivity, were stable under high temperature storage. The existence of the TiAl{sub 3} and NiAl{sub 3} intermetallic phases was helpful to prevent Al agglomeration on the interface and make the contacts thermally stable. Auger electron spectroscopy indicated that the incorporation of oxygen at the surface and interface led to the oxidation of Al or Ti resulting in increased contact resistance. Also, the formation of these oxides roughened the surface and interface. The temperature-dependence of the specific contact resistance indicated that a thermionic field emission mechanism dominates the current transport for contacts before and after the thermal treatment. It suggests that the Ni/Ti/Al composite ohmic contacts are promising for SiC devices to be used in high temperature applications.

Phase formation in as-solidified and heat-treated Al-Si-Cu-Mg-Ni alloys: Thermodynamic assessment and experimental investigation for alloy design

Energy Technology Data Exchange (ETDEWEB)

Farkoosh, A.R., E-mail: amir.rezaeifarkoosh@mail.mcgill.ca [Department of Mining and Materials Engineering, McGill University, 3610 University, Aluminum Research Center - REGAL, Montreal, Quebec, Canada H3A 2B2 (Canada); Javidani, M. [Laval University, Department of Mining, Metallurgy and Materials Engineering, Aluminum Research Center - REGAL, 1065 Ave de la Medecine, Quebec, Canada G1V 0A6 (Canada); Hoseini, M. [Department of Mining and Materials Engineering, McGill University, 3610 University, Aluminum Research Center - REGAL, Montreal, Quebec, Canada H3A 2B2 (Canada); Larouche, D. [Laval University, Department of Mining, Metallurgy and Materials Engineering, Aluminum Research Center - REGAL, 1065 Ave de la Medecine, Quebec, Canada G1V 0A6 (Canada); Pekguleryuz, M. [Department of Mining and Materials Engineering, McGill University, 3610 University, Aluminum Research Center - REGAL, Montreal, Quebec, Canada H3A 2B2 (Canada)

2013-02-25

Highlights: Black-Right-Pointing-Pointer Phase formation in Al-Si-Ni-Cu-Mg-Fe system have been investigated. Black-Right-Pointing-Pointer T-Al{sub 9}FeNi, {gamma}-Al{sub 7}Cu{sub 4}Ni, {delta}-Al{sub 3}CuNi and {epsilon}-Al{sub 3}Ni are formed at different Ni levels. Black-Right-Pointing-Pointer Thermally stable Ni-bearing precipitates improved the overaged hardness. Black-Right-Pointing-Pointer It was found that Ni:Cu and Ni:Fe ratios control the precipitation. Black-Right-Pointing-Pointer {delta}-Al{sub 3}CuNi phase has more contribution to strength compare to other precipitates. - Abstract: Thermodynamic simulations based on the CALPHAD method have been carried out to assess the phase formation in Al-7Si-(0-1)Ni-0.5Cu-0.35Mg alloys (in wt.%) under equilibrium and non-equilibrium (Scheil cooling) conditions. Calculations showed that the T-Al{sub 9}FeNi, {gamma}-Al{sub 7}Cu{sub 4}Ni, {delta}-Al{sub 3}CuNi and {epsilon}-Al{sub 3}Ni phases are formed at different Ni levels. By analyzing the calculated isothermal sections of the phase diagrams it was revealed that the Ni:Cu and Ni:Fe ratios control precipitation in this alloy system. In order to verify the simulation results, microstructural investigations in as-cast, solution treated and aged conditions were carried out using electron probe microanalysis (EPMA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Furthermore, cooling curve analysis (CCA) was also performed to determine the freezing range of the new alloys and porosity formation during solidification. Hardness measurements of the overaged samples showed that in this alloy system the {delta}-Al{sub 3}CuNi phase has a greater influence on the overall strength of the alloys compared to the other Ni-bearing precipitates.

Ni3Si(Al)/a-SiOx core shell nanoparticles: characterization, shell formation, and stability

Science.gov (United States)

Pigozzi, G.; Mukherji, D.; Gilles, R.; Barbier, B.; Kostorz, G.

2006-08-01

We have used an electrochemical selective phase dissolution method to extract nanoprecipitates of the Ni3Si-type intermetallic phase from two-phase Ni-Si and Ni-Si-Al alloys by dissolving the matrix phase. The extracted nanoparticles are characterized by transmission electron microscopy, energy-dispersive x-ray spectrometry, x-ray powder diffraction, and electron powder diffraction. It is found that the Ni3Si-type nanoparticles have a core-shell structure. The core maintains the size, the shape, and the crystal structure of the precipitates that existed in the bulk alloys, while the shell is an amorphous phase, containing only Si and O (SiOx). The shell forms around the precipitates during the extraction process. After annealing the nanoparticles in nitrogen at 700 °C, the tridymite phase recrystallizes within the shell, which remains partially amorphous. In contrast, on annealing in air at 1000 °C, no changes in the composition or the structure of the nanoparticles occur. It is suggested that the shell forms after dealloying of the matrix phase, where Si atoms, the main constituents of the shell, migrate to the surface of the precipitates.

Study on the Formation of Reaction Phase to Si Addition in Boron Steel Hot-Dipped in Al–7Ni Alloy

Directory of Open Access Journals (Sweden)

Jung-Gil Yun

2017-11-01

Full Text Available In order to reduce the intermetallic compounds formed during the application of an Al–7Ni wt % hot-dip multifunctional coating on boron steel, developed for Tailor Welded Blanks (TWB and hot stamping, 2–6 wt % Si was added to the coating to change the reaction layer. The coating was run at 690 °C for 120 s. Al9FeNi phases were formed on the steel interface, Fe2Al5 was formed on the steel, FeAl3 was generated between the existing layers, and flake-type Al2Fe3Si3 was formed in the Fe2Al5 phase, depending on the Si content. In addition, as Si was added to the coating, the thickness of the Fe2Al5 phase decreased and the thickness of the Al9FeNi phase and Al2Fe3Si3 increased. The decrease in the thickness of the Fe2Al5 phase was mainly due to the effect of the Si solid solution and the Al2Fe3Si3 formation in the Fe2Al5 phase. The reason for the growth of Al9FeNi is that the higher the Si content in the coating, the more the erosion of the interface of the steel material due to the coating solution. Therefore, the outflow of Fe into the coating liquid increased.

HIDRODENITROGENACION DE CARBAZOL SOBRE CATALIZADORES NiMo/Al2O3-SiO2(x

Directory of Open Access Journals (Sweden)

Felipe Sánchez-Minero

2012-01-01

Full Text Available En este trabajo se estudió la velocidad de reacción del carbazol sobre catalizadores NiMo soportados sobre Al2O3 modificada superficialmente con SiO2 (0 y 10 % en peso de SiO2 en el soporte. Los catalizadores fueron evaluados en un reactor intermitente a cuatro temperaturas (287, 300, 312 y 325oC, presión de 4.0 MPa y relación molar hidrogeno/carbazol de 2400. A partir de los resultados experimentales se realizó un estudio cinético utilizando ecuaciones del tipo Langmuir-Hinshelwood (L-H. Luego, los parámetros cinéticos fueron estimados mediante la minimización de Powell (programa Scientist de MicroMath. Los resultados muestran que el catalizador con sílice (NiMo-SAC 10 alcanza una mayor actividad para la HDN de carbazol debido a que presenta un mayor número de sitios activos (valor de A, así como una menor fuerza de adsorción entre el reactante y la superficie catalítica (valor de KN, lo cual posiblemente favorece una mejor regeneración de sitios activos.

La independencia del aprendizaje implícito con respecto a la inteligencia general en niños de edad escolar

OpenAIRE

López Ramón, María Fernanda; Introzzi, Isabel; Richard´s, Maria Marta

2009-01-01

Los resultados existentes en poblaciones de niños sobre el postulado de Reber (1993) acerca de la independencia del Aprendizaje Implícito con respecto a la Inteligencia son escasos y no concluyentes. Por ello, en el presente estudio nos propusimos analizar las relaciones existentes entre el Aprendizaje Implícito (AI) y la inteligencia General en niños de 7 a 11 años y documentar evidencia empírica adicional en éste grupo de edad utilizando pruebas específicamente creadas para evaluar a niños ...

Soft Magnetic Properties of High-Entropy Fe-Co-Ni-Cr-Al-Si Thin Films

Directory of Open Access Journals (Sweden)

Pei-Chung Lin

2016-08-01

Full Text Available Soft magnetic properties of Fe-Co-Ni-Al-Cr-Si thin films were studied. As-deposited Fe-Co-Ni-Al-Cr-Si nano-grained thin films showing no magnetic anisotropy were subjected to field-annealing at different temperatures to induce magnetic anisotropy. Optimized magnetic and electrical properties of Fe-Co-Ni-Al-Cr-Si films annealed at 200 °C are saturation magnetization 9.13 × 105 A/m, coercivity 79.6 A/m, out-of-plane uniaxial anisotropy field 1.59 × 103 A/m, and electrical resistivity 3.75 μΩ·m. Based on these excellent properties, we employed such films to fabricate magnetic thin film inductor. The performance of the high entropy alloy thin film inductors is superior to that of air core inductor.

Glass forming ability and mechanical properties of the NiZrTiSi amorphous alloys modified with Al, Cu and Nb additions

International Nuclear Information System (INIS)

Czeppe, Tomasz; Ochin, Patrick; Sypien, Anna

2007-01-01

The composition of the amorphous alloy Ni 59 Zr 20 Ti 16 Si 5 was modified with 2-9 at.% additions of Cu, Al and Nb. The ribbons and the bars 2.7 mm in diameter were prepared by melt spinning and injection casting from the alloys of the compositions: Ni 56 Zr 18 Ti 16 Si 5 Al 3 Cu 2 , Ni 56 Zr 18 Ti 13 Al 6 Si 5 Cu 2 , Ni 56 Zr 16 Ti 12 Nb 9 Al 3 Cu 2 Si 2 and Ni 56 Zr 16 Ti 12 Nb 6 Al 6 Cu 2 Si 2 . All ribbons were amorphous up to the resolution of the X-ray diffraction and conventional transmission electron microscopy, however rods were partially crystalline. Increase of Al content lowered and Nb content slightly increased crystallization start temperature T x and glass transition temperature T g . The influence of composition changes on the overcooled liquid range ΔT was more complicated. The increase of Nb and decrease of Ti and Zr content led to the remarkable increase of the liquidus temperature T l . As a result GFA calculated as T g /T l was lowered to the values about 0.63 for 6 and 9 at.% Nb addition. The activation energies for primary crystallization in alloy with 6 at.% Al and 6 at.% of Nb, were determined. The changes of tensile test strength and microhardness with Al and Nb additions showed hardening effect caused by Nb additions and increase in fracture strength with increasing Al content

Ni(3)Si(Al)/a-SiO(x) core-shell nanoparticles: characterization, shell formation, and stability.

Science.gov (United States)

Pigozzi, G; Mukherji, D; Gilles, R; Barbier, B; Kostorz, G

2006-08-28

We have used an electrochemical selective phase dissolution method to extract nanoprecipitates of the Ni(3)Si-type intermetallic phase from two-phase Ni-Si and Ni-Si-Al alloys by dissolving the matrix phase. The extracted nanoparticles are characterized by transmission electron microscopy, energy-dispersive x-ray spectrometry, x-ray powder diffraction, and electron powder diffraction. It is found that the Ni(3)Si-type nanoparticles have a core-shell structure. The core maintains the size, the shape, and the crystal structure of the precipitates that existed in the bulk alloys, while the shell is an amorphous phase, containing only Si and O (SiO(x)). The shell forms around the precipitates during the extraction process. After annealing the nanoparticles in nitrogen at 700 °C, the tridymite phase recrystallizes within the shell, which remains partially amorphous. In contrast, on annealing in air at 1000 °C, no changes in the composition or the structure of the nanoparticles occur. It is suggested that the shell forms after dealloying of the matrix phase, where Si atoms, the main constituents of the shell, migrate to the surface of the precipitates.

Photoconducting and photocapacitance properties of Al/p-CuNiO{sub 2}-on-p-Si isotype heterojunction photodiode

Energy Technology Data Exchange (ETDEWEB)

Elsayed, I.A. [Physics Department, College of Science and Humanitarian Studies, Salman bin Abdulaziz University (Saudi Arabia); Physics Department, Faculty of Science, Damietta University (Egypt); Çavaş, Mehmet [Department of Mechatronics, Faculty of Technology, Firat University, Elazig (Turkey); Gupta, R. [Department of Chemistry, Pittsburg State University, Pittsburg, KS 66762 (United States); Fahmy, T. [Physics Department, College of Science and Humanitarian Studies, Salman bin Abdulaziz University (Saudi Arabia); Polymer Research Group, Physics Department, Faculty of Science, Mansoura University (Egypt); Al-Ghamdi, Ahmed A. [Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Yakuphanoglu, F., E-mail: fyhan@hotmail.com [Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Physics Department, Faculty of Science, Firat University, Elazig (Turkey)

2015-07-25

Highlights: • The CuNiO{sub 2} thin film was prepared by sol gel method. • The diode has a high photosensitivity value of 1.02 × 10{sup 3} under 100 mW/cm{sup 2}. • Al/p-Si/CuNiO{sub 2}/Al can used in optoelectronic device applications. - Abstract: Thin film of CuNiO{sub 2} was prepared by sol gel method to fabricate a photodiode. The surface morphology of the CuNiO{sub 2} thin film was investigated by atomic force microscopy (AFM). AFM results indicated that CuNiO{sub 2} film was formed from the nanoparticles and the average size of the nanoparticles was about 115 nm. The optical band gap of CuNiO{sub 2} film was calculated using optical data and was found to be about 2.4 eV. A photodiode having a structure of Al/p-Si/CuNiO{sub 2}/Al was prepared. The electronic parameters such as ideality factor and barrier height of the diode were determined and were obtained to be 8.23 and 0.82 eV, respectively. The interface states properties of the Al/p-Si/CuNiO{sub 2}/Al diode was performed using capacitance–voltage and conductance–voltage characteristics. The series resistance of the Al/p-Si/CuNiO{sub 2}/Al photo diode was observed to be decreasing with increasing frequency. The diode exhibited a photoconducting behavior with a high photosensitivity value of 1.02 × 10{sup 3} under 100 mW/cm{sup 2}. The obtained results indicate that Al/p-Si/CuNiO{sub 2}/Al can used in optoelectronic device applications.

Magnetic, structural and magnetocaloric properties of Ni-Si and Ni-Al thermoseeds for self-controlled hyperthermia.

Science.gov (United States)

Pandey, Sudip; Quetz, Abdiel; Aryal, Anil; Dubenko, Igor; Mazumdar, Dipanjan; Stadler, Shane; Ali, Naushad

2017-11-01

Self-controlled hyperthermia is a non-invasive technique used to kill or destroy cancer cells while preserving normal surrounding tissues. We have explored bulk magnetic Ni-Si and Ni-Al alloys as a potential thermoseeds. The structural, magnetic and magnetocaloric properties of the samples were investigated, including saturation magnetisation, Curie temperature (T C ), and magnetic and thermal hysteresis, using room temperature X-ray diffraction and magnetometry. The annealing time, temperature and the effects of homogenising the thermoseeds were studied to determine the functional hyperthermia applications. The bulk Ni-Si and Ni-Al binary alloys have Curie temperatures in the desired range, 316 K-319 K (43 °C-46 °C), which is suitable for magnetic hyperthermia applications. We have found that T C strictly follows a linear trend with doping concentration over a wide range of temperature. The magnetic ordering temperature and the magnetic properties can be controlled through substitution in these binary alloys.

Relevancia valorativa del resultado global y sus Componentes frente al resultado neto

Directory of Open Access Journals (Sweden)

Núria Arimany Serrat

2011-08-01

Full Text Available Este trabajo tiene como objeto verificar si el resultado global presenta mayor relevancia valorativa respecto al resultado tradicional, y si es así cuáles son los componentes del resultado global que explican las diferencias. El estudio muestra que el resultado global es una variable relevante tanto para explicar el valor intrínseco de la empresa como para explicar su rentabilidad. Sin embargo, sólo al explicar la rentabilidad el resultado global y su incremento aumentan la relevancia valorativa del resultado neto y su incremento. De los componentes analizados del resultado global, tan sólo los resultados por diferencias de conversión de la moneda extranjera a la moneda de presentación añaden poder explicativo adicional al del resultado neto, aunque sólo en los modelos de rentabilidad. Ni los resultados por valoración de instrumentos financieros a valor razonable con cambios en patrimonio ni los resultados por coberturas de flujos de efectivo aportan un mayor poder explicativo al del resultado neto.

Perfil cognitivo de niños con rendimientos bajos en comprensión lectora

Directory of Open Access Journals (Sweden)

Lorena Canet-Juric

2013-10-01

Full Text Available La mayoría de los niños con dificultades en la comprensión lectora poseen rendimientos inferiores en un conjunto de procesos cognitivos. El objetivo del presente estudio es establecer un perfil cognitivo asociado al bajo rendimiento en comprensión lectora en relación a la habilidad de monitoreo, a la producción de inferencias, al vocabulario, a la amplitud de memoria de trabajo y a la capacidad inhibitoria, en niños hispanoparlantes. Para ello se administraron tareas correspondientes a dichos procesos en niños con altos y bajos rendimientos en comprensión lectora. Los resultados mostraron que si bien los niños con mala comprensión presentan bajos rendimientos en estas habilidades, no puede establecerse un perfil consistente ya que hay niños con problemas en comprensión que presentan normal o superior rendimiento en algunas de estas habilidades cognitivas.

Dynamic magnetization of NiZn ferrite doped FeSiAl thin films fabricated by oblique sputtering

Energy Technology Data Exchange (ETDEWEB)

Zhong, Xiaoxi, E-mail: xiaoxi.zhong@gmail.com [Sichuan Province Key Laboratory of Information Materials and Devices Application, Chengdu University of Information Technology, Chengdu 610225 (China); Phuoc, Nguyen N. [Temasek Laboratories, National University of Singapore, 5A Engineering Drive 2, Singapore 117411 (Singapore); Soh, Wee Tee [Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117542 (Singapore); Ong, C.K. [Temasek Laboratories, National University of Singapore, 5A Engineering Drive 2, Singapore 117411 (Singapore); Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117542 (Singapore); Li, Lezhong [Sichuan Province Key Laboratory of Information Materials and Devices Application, Chengdu University of Information Technology, Chengdu 610225 (China)

2017-06-15

Highlights: • We prepared NiZn ferrite doped FeSiAl-based thin films using oblique deposition technique. • The magnetic properties of FeSiAl-based thin films were systematically studied. • Two ferromagnetic resonance peaks were observed in the permeability spectra. • The thermal stability of microwave properties of FeSiAl-based films was studied. • The thermal stability of properties we studied was relatively good. - Abstract: In this study, we comprehensively investigate the dynamic magnetic properties of FeSiAl-NiZnFeO thin films prepared by the oblique deposition method via a shorted microstrip perturbation technique. For the films with higher oblique angle and NiZn ferrite doping amount, there are two ferromagnetic resonance peaks observed in the permeability spectra, and both of the two peaks originate from FeSiAl. Furthermore, the magnetic anisotropy field H{sub K} of the ferromagnetic resonance peak at higher frequency is enhanced with increasing doping amount, which is interpreted in terms of the contribution of reinforced stress-induced anisotropy and shape anisotropy brought about by doping elements and oblique sputtering method. In addition, the thermal stability of the ferromagnetic resonance frequency f{sub FMR} of FeSiAl-NiZnFeO films with oblique angles of 35° and 45° with respect to temperature ranging from 300 K to 420 K is deteriorated with increasing ferrite doping amount, which is mainly ascribed to the influence of pair-ordering anisotropy and/or the reduction of the FeSiAl grain size.

Ultrathin highly uniform Ni(Al) germanosilicide layer with modulated B8 type Ni5(SiGe)3 phase formed on strained Si1−xGex layers

International Nuclear Information System (INIS)

Liu, Linjie; Xu, Dawei; Jin, Lei; Knoll, Lars; Wirths, Stephan; Nichau, Alexander; Buca, Dan; Mussler, Gregor; Holländer, Bernhard; Zhao, Qing-Tai; Mantl, Siegfried; Feng Di, Zeng; Zhang, Miao

2013-01-01

We present a method to form ultrathin highly uniform Ni(Al) germanosilicide layers on compressively strained Si 1−x Ge x substrates and their structural characteristics. The uniform Ni(Al) germanosilicide film is formed with Ni/Al alloy at an optimized temperature of 400 °C with an optimized Al atomic content of 20 at. %. We find only two kinds of grains in the layer. Both grains show orthogonal relationship with modified B8 type phase. The growth plane is identified to be (10-10)-type plane. After germanosilicidation the strain in the rest Si 1−x Ge x layer is conserved, which provides a great advantage for device application

Vacuum brazing of electroless Ni-P alloy-coated SiCp/Al composites using aluminum-based filler metal foil

Science.gov (United States)

Wang, Peng; Xu, Dongxia; Niu, Jitai

2016-12-01

Using rapidly cooled (Al-10Si-20Cu-0.05Ce)-1Ti (wt%) foil as filler metal, the research obtained high-performance joints of electroless Ni-P alloy-coated aluminum matrix composites with high SiC particle content (60 vol%, SiCp/Al-MMCs). The effect of brazing process on joint properties and the formation of Al-Ni and Al-Cu-Ni intermetallic compounds were investigated, respectively. Due to the presence of Ni-P alloy coating, the wettability of liquid filler metal on the composites was improved obviously and its contact angle was only 21°. The formation of Al3Ni2 and Al3(CuNi)2 intermetallic compounds indicated that well metallurgical bonding occurred along the 6063Al matrix alloy/Ni-P alloy layer/filler metal foil interfaces by mutual diffusion and dissolution. And the joint shear strength increased with increasing the brazing temperature from 838 to 843 K or prolonging the soaking time from 15 to 35 min, while it decreased a lot because of corrosion occurring in the 6063Al matrix at high brazing temperature of 848 K. Sound joints with maximum shear strength of 112.5 MPa were obtained at 843 K for soaking time of 35 min. In this research, the beneficial effect of surface metallization by Ni-P alloy deposits on improving wettability on SiCp/Al-MMCs was demonstrated, and capable welding parameters were broadened as well.

Microstructural evolution of neutron-irradiated Ni-Si and Ni-Al alloys

Science.gov (United States)

Takahashi, H.; Garner, F. A.

1992-10-01

Additions of silicon and aluminum suppress the neutron-induced swelling of pure nickel but to different degrees. Silicon is much more effective initially when compared to aluminum on a per atom basis but silicon exhibits a nonmonotonic influence on swelling with increasing concentration. Silicon tends to segregate toward grain boundaries while aluminum segregates away from these boundaries. Whereas the formation of the Ni 3Si phase is frequently observed in charged particle irradiation experiments conducted at much higher displacement rates, it did not occur during neutron irradiation in this study. Precipitation also did not occur in Ni-5Al during neutron irradiation, nor has it been reported to occur during ion irradiation.

Microstructural evolution of neutron-irradiated Ni-Si and Ni-Al alloys

International Nuclear Information System (INIS)

Takahashi, H.; Garner, F.A.

1992-01-01

Additions of silicon and aluminium suppress the neutron-induced swelling of pure nickel but to different degrees. Silicon is much more effective initially when compared to aluminium on a per atom basis but silicon exhibits a nonmonotonic influence on swelling with increasing concentration. Silicon tends to segregate toward grain boundaries while aluminium segregates away from these boundaries. Whereas the formation of the Ni 3 Si phase is frequently observed in charged particle irradiation experiments conducted at much higher displacement rates, it did not occur during neutron irradiation in this study. Precipitation also did not occur in Ni-5Al during neutron irradiation, nor has it been reported to occur during ion irradiation. (orig.)

Hot stage nanoindentation in multi-component Al-Ni-Si alloys: Experiment and simulation

Energy Technology Data Exchange (ETDEWEB)

Richter, A. [Institute of Polymer Technology and Materials Engineering, Loughborough University, Loughborough LE11 3TU (United Kingdom); Department of Engineering, University of Applied Sciences Wildau (Berlin), Bahnhofstrasse 1, Wildau 15745 (Germany)], E-mail: asta.richter@tfh-wildau.de; Chen, C.-L. [Institute of Polymer Technology and Materials Engineering, Loughborough University, Loughborough LE11 3TU (United Kingdom); Smith, R.; McGee, E. [Department of Mathematical Sciences, Loughborough University, Loughborough LE11 3TU (United Kingdom); Thomson, R.C. [Institute of Polymer Technology and Materials Engineering, Loughborough University, Loughborough LE11 3TU (United Kingdom); Kenny, S.D. [Department of Mathematical Sciences, Loughborough University, Loughborough LE11 3TU (United Kingdom)

2008-10-25

The mechanical properties of individually pure and intermetallic phases of typical Al-Ni-Si piston alloys are investigated at different temperatures using hot stage nanoindentation. The hardness and the indentation modulus of a number of phases are determined at room temperature, 500 K and 650 K. Both, hardness and reduced modulus drop with increasing temperature in different ratios for the various phases. Increasing Ni content in the grains improves the mechanical stability of the material at elevated temperatures in general. The indentation patterns are studied using atomic force microscopy with particular reference to the indentation depths and pile-up effects. Site-specific samples from the material surrounding the nanoindents are prepared using a focussed ion beam field emission gun for examination in the transmission electron microscope. This allows direct observation of material changes as a result of the indentation process in the different phases within the alloy system. Corresponding linked atomistic finite element calculations have been carried out for Si and Ni-Al systems as a function of increasing Ni content at various temperatures. The results show only a small difference in the mechanical behaviour of Si between 300 K and 650 K as observed in the experiments. Large differences for Al at both temperatures studied result in an increase of plasticity with rising temperature and atomic motion that changes from slip in well-defined planes to a viscous fluid-like behaviour. The formation of dislocations and slip bands during indentation for the Ni-Al systems is studied.

Effect of Si addition on the glass-forming ability of a NiTiZrAlCu alloy

International Nuclear Information System (INIS)

Liang, W.Z.; Shen, J.; Sun, J.F.

2006-01-01

The effect of Si addition on the glass-forming ability (GFA) of a NiTiZrAlCu alloy was investigated by using differential scanning calorimetry (DSC), differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The maximum diameter of glassy rods increased from 0.5 mm for the Ni 42 Ti 20 Zr 25 Al 8 Cu 5 alloy (the base alloy) to 2.5 mm for the Ni 42 Ti 20 Zr 21.5 Al 8 Cu 5 Si 3.5 alloy and to 3 mm for the Ni 42 Ti 19 Zr 22.5 Al 8 Cu 5 Si 3.5 alloy, when prepared by using the copper mould casting. The GFA of the alloys can be assessed by the reduced glass transition temperature T rg (=T g /T l ) and a newly proposed parameter, δ(=T x /T l - T g ). An addition of a proper amount of Si and a minor substitution of Ti with Zr can enhance the GFA of the base alloy by suppressing the formation of primary Ni(TiZr) and (TiZr)(CuAl) 2 phases and inducing the composition close to eutectic

Electrical characterization of Ni/n-ZnO/p-Si/Al heterostructure fabricated by pulsed laser deposition technique

International Nuclear Information System (INIS)

Chand, Subhash; Kumar, Rajender

2014-01-01

Highlights: • The Ni/n-ZnO/p-Si/Al heterojunction diodes are fabricated by pulsed laser deposition. • The band gap of the deposit ZnO films was found to be 3.43 eV. • Forward I–V data of Ni/n-ZnO/p-Si/Al hetrojunction are interpreted in terms of thermionic emission–diffusion mechanism. • The C–V characteristics of the Ni/n-ZnO/p-Si/Al hetrojunction diode are measured in the temperature range 80–300 K. • The barrier height of Ni/n-ZnO/p-Si/Al hetrojunction diode is also calculated from C–V measurements. - Abstract: The ZnO thin films are grown on the p-Si for the heterojunction fabrication by pulsed laser deposition method. X-ray diffraction study showed that the texture of the film is hexagonal with a strong (0 0 2) plane as preferred direction. High purity vacuum evaporated nickel and aluminum metals were used to make contacts to the n-ZnO and p-Si, respectively. The current–voltage characteristics of Ni/n-ZnO/p-Si(1 0 0)/Al hetero structure measured over the temperature range 80–300 K have been studied on the basis of thermionic emission diffusion mechanism. The equivalent Schottky barrier height and diode ideality factor are determined by fitting of measured current–voltage data in to thermionic diffusion equation. It is observed that the barrier height decreases and the ideality factor increases with decrease of temperature and the activation energy plot exhibit non-linear behavior. These characteristics are attributed to the Gaussian distribution of barrier heights. The capacitance–voltage characteristics of Ni/n-ZnO/p-Si(1 0 0)/Al heterojunction diode are also studied over wide temperature range. From the measured capacitance–voltage data the built in voltage and impurity concentration in n-type ZnO is estimated

Trastorno Somatosensorial en niños con Trastornos por Déficit de Atención con Hiperactividad.

OpenAIRE

Romero Ayuso, Dulce María

2016-01-01

Introducción: El estudio de los trastornos por déficit de atención (ADHD) se ha centrado en la falta de control inhibitorio como déficit primario, aunque su fisiopatología también se ha relacionado con la corteza somatosensorial. El objetivo de este trabajo fue conocer si existe un trastorno para la discriminación sensorial táctil y praxis en los niños con ADHD y si éste es similar en los subtipos inatento (ADHD-I) y combinado (ADHD-C). Método: los participantes fueron 74 niños entre 7 y 11 a...

Relaciones interpersonales en el nuevo modelo de atención sanitarista al niño con dolor

Directory of Open Access Journals (Sweden)

Ana María Collado Madurga

Full Text Available Introducción: el alivio del dolor debe considerase un derecho fundamental de la persona, porque el respeto a la dignidad humana exige que nadie sufra dolor innecesario. Objetivo: valorar cómo se establecía la relación de los profesionales con el paciente y representantes válidos, en la atención a niños con dolor, y si se ajustaban a un modelo de afrontamiento ético de las relaciones interpersonales y las valoraciones sobre virtudes y cualidades presentes en los profesionales que atienden niños con dolor. Métodos: se realizó una investigación descriptiva-transversal utilizando métodos cualitativos. Se realizaron encuestas a tutores válidos de niños que padecían dolor ingresados en el Hospital Pediátrico "Juan Manuel Márquez", y a profesionales de ese hospital de diferentes servicios que atienden a niños con dolor. Las valoraciones de los profesionales sobre estas relaciones se contrastaron con las que hicieron los representantes legales de los niños con dolor atendidos en el hospital. Resultados: el personal de salud considera generalmente (casi siempre correctas las valoraciones bioéticas en la relación médica con los enfermos y familiares. Los tutores válidos de los niños ingresados escogieron la alternativa siempre correcta en los procederes orientados desde la Bioética por parte del personal de salud. Las cualidades que caracterizan al personal médico y de enfermería son apreciadas en el rango de suficiente, y estas, con relación a cómo deberían estar presentes, las frecuencias no fueron lo suficientemente elevadas para esta profesión. Conclusiones: se constató que la ponderación de valores deseados para la profesión no alcanza las expectativas necesarias para considerar que se estén formando profesionales virtuosos. Los profesionales valoraron que no siempre se cumplen los procederes orientados desde la bioética, sin embargo los padres consideran que estos son cumplidos siempre.

Microstructure and mechanical properties of Al-Si-X alloys fabricated by gas atomization and extrusion process

International Nuclear Information System (INIS)

Lee, T.H.; Hong, S.J.

2009-01-01

In order to develop good wear resistant and high-strength alloys, Al 81 Si 19 alloy was reinforced with transition elements such as Ni and Ce. The solubility of Si in aluminum was amplified, with increasing the Ni and Ce content in the rapidly solidified powders. The extruded bars consist of homogeneously dispersed fine Si particles along with Al 3 Ni and Al 3 Ce compounds (30-120 nm) in aluminum matrix (grain size below 500 nm). The tensile strength at room temperature for Al 81 Si 19 , Al 78 Si 19 Ni 2 Ce 0.5 and Al 76 Si 19 Ni 4 Ce 1 bars extruded at 400 deg. C was estimated as 281, 521, and 668 MPa, respectively. In addition, the maximum tensile strength of 730 MPa was attained in Al 73 Si 19 Ni 7 Ce 1 bulk alloy. The uniform dispersion of precipitates (Si, Al 3 Ni and Al 3 Ce particles) from the supersaturated Al matrix of ternary and quaternary alloys after extrusion was effective for enhanced mechanical properties.

Microstructures and microhardness evolutions of melt-spun Al-8Ni-5Nd-4Si alloy

Energy Technology Data Exchange (ETDEWEB)

Karakoese, Ercan, E-mail: ekarakose@karatekin.edu.tr [Karatekin University, Faculty of Sciences, Department of Physics, 18100 Cank Latin-Small-Letter-Dotless-I r Latin-Small-Letter-Dotless-I (Turkey); Keskin, Mustafa [Erciyes University, Faculty of Sciences, Department of Physics, 38039 Kayseri (Turkey)

2012-03-15

Al-Ni-Nd-Si alloy with nominal composition of Al-8 wt.%Ni-5 wt.%Nd-4 wt.%Si was rapidly solidified by using melt-spinning technique to examine the influence of the cooling rate/conditions on microstructure and mechanical properties. The resulting conventional cast (ingot) and melt-spun ribbons were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy together with energy dispersive spectroscopy, differential scanning calorimetry, differential thermal analysis and Vickers microhardness tester. The ingot alloys consists of four phases namely {alpha}-Al, intermetallic Al{sub 3}Ni, Al{sub 11}Nd{sub 3} and fcc Si. Melt-spun ribbons are completely composed of {alpha}-Al phase. The optical microscopy and scanning electron microscopy results show that the microstructures of rapidly solidified ribbons are clearly different from their ingot alloy. The change in microhardness is discussed based on the microstructural observations. - Highlights: Black-Right-Pointing-Pointer Rapid solidification allows a reduction in grain size, extended solid solution ranges. Black-Right-Pointing-Pointer We observed the matrix lattice parameter increases with increasing wheel speed. Black-Right-Pointing-Pointer Melt-spun ribbons consist of partly amorphous phases embedded in crystalline phases. Black-Right-Pointing-Pointer The solidification rate is high enough to retain most of alloying elements in the Al matrix. Black-Right-Pointing-Pointer The rapid solidification has effect on the phase constitution.

Contribución de la terapia psicomotriz al progreso de niños con discapacidades

Directory of Open Access Journals (Sweden)

Marguerite Heron-Flores

2018-01-01

Full Text Available Introducción. Independiente a la edad, la psicomotricidad incide en el desarrollo de las personas, por lo que es un aspecto de interés para profesionales de la salud, la rehabilitación, la educación y los servicios sociales. Objetivo. Determinar en qué medida un programa psicomotor de intervención, implementado en niños con diferentes discapacidades, contribuye a la mejoría de dichos trastornos psicomotores y a su adaptación en el medio ambiente. Materiales y métodos. Se implementó un diseño pre y post evaluación enmarcado en el paradigma de Mixed Methods, con programa de intervención durante 7 meses y con 13 participantes con diferentes niveles de trastornos psicomotores. Los instrumentos de medida fueron test psicomotores cuantitativos, hojas de registro de observación y cuestionarios y entrevistas cualitativas a las familias. Resultados. Tras la aplicación del programa se producen mejoras en la evolución psicomotriz de los niños en el esquema corporal, en la coordinación dinámica general, en la estructuración espacial, en la motricidad fina y en la adaptación del niño al medio ambiente. Conclusiones. Es necesario que las terapias utilizadas en personas con discapacidades presenten una visión holística de la persona, atendiendo tanto los aspectos motores como psicológicos.

Improved mechanical properties of near-eutectic Al-Si piston alloy through ultrasonic melt treatment

Energy Technology Data Exchange (ETDEWEB)

Jung, Jae-Gil; Lee, Sang-Hwa [Implementation Research Division, Korea Institute of Materials Science (KIMS), Changwon 51508 (Korea, Republic of); Lee, Jung-Moo, E-mail: jmoolee@kims.re.kr [Implementation Research Division, Korea Institute of Materials Science (KIMS), Changwon 51508 (Korea, Republic of); Cho, Young-Hee [Implementation Research Division, Korea Institute of Materials Science (KIMS), Changwon 51508 (Korea, Republic of); Kim, Su-Hyeon [Metal Materials Division, Korea Institute of Materials Science (KIMS), Changwon 51508 (Korea, Republic of); Yoon, Woon-Ha [Implementation Research Division, Korea Institute of Materials Science (KIMS), Changwon 51508 (Korea, Republic of)

2016-07-04

The effects of ultrasonic melt treatment (UST) on the microstructure and mechanical properties of Al-12.2Si-3.3Cu-2.4Ni-0.8Mg-0.1Fe (wt%) piston alloy were systematically investigated. Rigid colonies consisting of primary Si, eutectic Si, Mg{sub 2}Si and various aluminides (ε-Al{sub 3}Ni, δ-Al{sub 3}CuNi, π-Al{sub 8}FeMg{sub 3}Si{sub 6}, γ-Al{sub 7}Cu{sub 4}Ni, Q-Al{sub 5}Cu{sub 2}Mg{sub 8}Si{sub 6} and θ-Al{sub 2}Cu) were observed in the as-cast alloys. The sizes of the secondary phases, eutectic cell and grain were significantly decreased by UST because of the enhanced nucleation of each phase under ultrasonic irradiation. The yield strength, tensile strength and elongation at 25 °C were significantly improved by UST mainly because of the refinement of the microstructures. Both tensile strength and elongation at 350 °C were also improved by UST despite the unchanged yield strength.

Efecto del dopado con Si sobre la estructura de defectos en sistemas heteroepitaxiales GaN/AlN/Si(111

Directory of Open Access Journals (Sweden)

Sánchez, A. M.

2000-08-01

Full Text Available The Si doping effect on the defect structure in GaN epilayers grown by molecular beam epitaxy on Si(111 substrates using AlN buffer layers has been studied. Transmission electron microscopy and related techniques have been used to carry out the structural characterization. The Si doping affects both the subgrain size and misorientation in GaN epilayer mosaic structure. The Si doping also leads to an increase of the planar defect density, as well as a decrease of the threading dislocation density. The enlargement of the subgrain tilt and the planar defect density explain the reduction of the dislocation density reaching the GaN free surface.

En el presente artículo se lleva a cabo el análisis del efecto que el dopado con Si tiene sobre la estructura de defectos en epicapas de GaN crecidas por epitaxia de haces moleculares sobre sustratos de Si (111 utilizando capas amortiguadoras de AlN. La caracterización estructural se llevó a cabo mediante microscopía electrónica de transmisión convencional y de alta resolución. El dopado con Si afecta a la desorientación y tamaño de los subgranos que constituyen la estructura mosaico de la epicapa de GaN. El dopado con Si provoca un aumento en la densidad de defectos planares, así como una disminución en la densidad de dislocaciones de propagación. El incremento en el grado de desorientación de inclinación, así como en la densidad de defectos planares que se produce conforme aumenta el dopado con Si explican la disminución en la densidad de dislocaciones que alcanzan la superficie libre de GaN.

Characterization of Ni-P-SiO_2-Al_2O_3 nanocomposite coatings on aluminum substrate

International Nuclear Information System (INIS)

Rahemi Ardakani, S.; Afshar, A.; Sadreddini, S.; Ghanbari, A.A.

2017-01-01

In the present work, nano-composites of Ni-P-SiO_2-Al_2O_3 were coated on a 6061 aluminum substrate. The surface morphology of the nano-composite coating was studied by field emission scanning electron microscopy (FESEM). The amount of SiO_2 in the coating was determined by Energy Dispersive Analysis of X-Ray (EDX) and the crystalline structure of the coating was examined by X-ray diffractometer (XRD). All the experiments concerning the corrosion behavior of the coating carried out in 3.5%wt NaCl solution and evaluated by electrochemical impedance spectroscopy (EIS) and polarization technique. The results showed that an incorporation of SiO_2 and Al_2O_3 in Ni-P coating at the SiO_2 concentration of 10 g/L and 14 g/L Al_2O_3 led to the lowest corrosion rate (i_c_o_r_r = 0.88 μA/cm"2), the most positive E_c_o_r_r and maximum microhardness (537 μHV). Furthermore, increasing the amount of nanoparticles in the coating was found to decrease CPE_d_l and improve porosity. - Highlights: • The maximum content of Al_2O_3 and SiO_2 in the coating was increased to 14.02%wt and 4.54%wt, respectively. • By enhancing the amount of nanoparticles in the coating, there was higher corrosion resistance. • Increasing the nanoparticles content in the coating improved microhardness of coating. • The maximum of microhardness of Ni-P-SiO_2-Al_2O_3 was measured to be 537 μHV.

Synergetic Effect of Ni2P/SiO2 and γ-Al2O3 Physical Mixture in Hydrodeoxygenation of Methyl Palmitate

Directory of Open Access Journals (Sweden)

Ivan V. Shamanaev

2017-11-01

Full Text Available The Ni2P/SiO2 catalyst, which was prepared by in situ temperature-programmed reduction and in the mixture with the inert (SiC, SiO2 or acidic (γ-Al2O3 material was studied in methyl palmitate hydrodeoxygenation (HDO. Methyl palmitate HDO was carried out at temperatures of 270–330 °C, H2/feed volume ratio of 600 Nm3/m3, and H2 pressure of 3.0 MPa. Ni2P/SiO2 catalyst, diluted with γ-Al2O3 showed a higher activity than Ni2P/SiO2 catalyst diluted with SiC or SiO2. The conversion of methyl palmitate increased significantly in the presence of γ-Al2O3 most probably due to the acceleration of the acid-catalyzed reaction of ester hydrolysis. The synergism of Ni2P/SiO2 and γ-Al2O3 in methyl palmitate HDO can be explained by the cooperation of the metal sites of Ni2P/SiO2 and the acid sites of γ-Al2O3 in consecutive metal-catalyzed and acid-catalyzed reactions of HDO. The obtained results let us conclude that the balancing of metal and acid sites plays an important role in the development of the efficient catalyst for the HDO of fatty acid esters over supported phosphide catalysts.

Interfacial mixing in double-barrier magnetic tunnel junctions with amorphous NiFeSiB layers

International Nuclear Information System (INIS)

Chun, B.S.; Ko, S.P.; Hwang, J.Y.; Rhee, J.R.; Kim, T.W.; Kim, Y.K.

2007-01-01

Double-barrier magnetic tunnel junctions (DMTJs) comprising Ta 45/Ru 9.5/IrMn 10/CoFe 7/AlO x /free layer (CoFe 4/NiFeSiB 2/CoFe 4, CoFe 10, or NiFeSiB 10)/AlO x /CoFe 7/IrMn 10/Ru 60 (nm) have been examined with an emphasis given on understanding the interfacial mixing effects. The DMTJ, consisted of NiFeSiB, shows low switching field and low bias voltage dependence because the amorphous NiFeSiB has lower M S (=800 emu/cm 3 ) and offers smoother interfaces than polycrystalline CoFe. An interesting feature observed in the CoFe/NiFeSiB/CoFe sandwich free layered DMTJ is the presence of a wavy MR transfer curve at high-resistance region. Because the polycrystalline CoFe usually grows into a columnar structure, diamagnetic CoSi, paramagnetic FeSi, and/or diamagnetic CoB might have been formed during the sputter-deposition process. By employing electron energy loss spectrometry (EELS) and Auger electron spectroscopy (AES), we were able to confirm that Si and B atoms were arranged evenly in the top and bottom portions of AlO x /CoFe interfaces. This means that the interfacial mixing resulted in a distorted magnetization reversal process

RF and microwave noise suppression in a transmission line using Fe-Si-Al/Ni-Zn magnetic composite films

International Nuclear Information System (INIS)

Lee, J. W.; Hong, Y. K.; Kim, K.; Joo, J.; Yoon, Y. W.; Kim, S. W.; Kim, Y. B.; Kim, K. Y.

2006-01-01

Radio-frequency (RF) and microwave noise suppression by using magnetic composite films on a microstrip line (MSL) was studied in the frequency range from 50 MHz to 13.5 GHz. The MSL was composed of a Cu transmission line, dielectric materials, and a Cu substrate. The Fe-Si-Al/Ni-Zn magnetic composite films were placed on the MSL, and the reflection and the transmission characteristics were investigated. We observed that RF and microwave noise suppression caused by the Fe-Si-Al/Ni-Zn magnetic composite films varied with the concentration ratio of the sendust (Fe-Si-Al) and the Ni-Zn ferrite. The frequency dependence of the power loss due to the composite films on the MSL was measured and the power loss increased at higher frequencies with increasing concentration of the sendust in the composites. The electromagnetic interference shielding efficiencies of the magnetic composite films in the far-field region are also discussed.

Magnetic ordering of YPd{sub 2}Si-type HoNi{sub 2}Si and ErNi{sub 2}Si compounds

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, GSP-2, Moscow, 119992 (Russian Federation); Isnard, O. [CNRS, Insitut. Néel, 25 Rue Des Martyrs BP166 x, F-38042 Grenoble (France); Université Grenoble Alpes, Inst. Néel, F-38042 Grenoble (France); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600 036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59082-970 (Brazil)

2016-12-01

Magnetic properties of YPd{sub 2}Si-type HoNi{sub 2}Si and ErNi{sub 2}Si were investigated via neutron diffraction and magnetisation measurements. HoNi{sub 2}Si and ErNi{sub 2}Si show ferromagnetic-like ordering at T{sub C} of 9 K and 7 K, respectively. The paramagnetic Weiss temperatures are 9 K and 11 K and the effective magnetic moments are 10.76 μ{sub B}/fu and 9.79 μ{sub B}/fu for HoNi{sub 2}Si and ErNi{sub 2}Si compounds, respectively. The HoNi{sub 2}Si and ErNi{sub 2}Si are soft ferromagnets with saturation magnetization of 8.1 μ{sub B}/fu and 7.5 μ{sub B}/fu, respectively at 2 K and in field of 140 kOe. The isothermal magnetic entropy change, ΔS{sub m}, has a maximum value of −15.6 J/kg·K at 10 K for HoNi{sub 2}Si and −13.9 J/kg·K at 6 K for ErNi{sub 2}Si for a field change of 50 kOe. Neutron diffraction study in zero applied field shows mixed ferromagnetic-antiferromagnetic ordering of HoNi{sub 2}Si at ~9 K and its magnetic structure is a sum of a-axis ferromagnetic F{sub a}, b-axis antiferromagnetic AF{sub b} and c-axis antiferrromagnetic AF{sub c} components of Pn′a2{sub 1}′={1, m_x′/[1/2, 1/2, 1/2], 2_y′/[0, 1/2, 0], m_z/[1/2, 0, 1/2]} magnetic space group and propagation vector K{sub 0}=[0, 0, 0]. The holmium magnetic moment reaches a value of 9.23(9) μ{sub B} at 1.5 K and the unit cell of HoNi{sub 2}Si undergoes isotropic contraction around the temperature of magnetic transition. - Graphical abstract: HoNi{sub 2}Si: mixed ferro-antiferromagnet (F{sub a}+AF{sub b}+AF{sub c}){sup K0} with Pn′a2{sub 1}′ magnetic space group and K{sub 0}=[0, 0, 0] propagation vector below 10 K. - Highlights: • Ferro-antiferromagnetic ordering is observed in HoNi{sub 2}Si at 9 K and in ErNi{sub 2}Si at 7 K. • HoNi{sub 2}Si is soft ferromagnet with ΔS{sub m} of −15.6 J/kg·K at 10 K in field of 0–50 kOe. • ErNi{sub 2}Si is soft ferromagnet with ΔS{sub m} of −13.9 J/kg·K at 6 K in field of 0–50 kOe. • HoNi{sub 2}Si shows mixed F�

Corrosion Behavior and Microhardness of Ni-P-SiO2-Al2O3 Nano-composite Coatings on Magnesium Alloy

Science.gov (United States)

Sadreddini, S.; Rahemi Ardakani, S.; Rassaee, H.

2017-05-01

In the present work, nano-composites of Ni-P-SiO2-Al2O3 were coated on AZ91HP magnesium alloy. The surface morphology of the nano-composite coating was studied by field emission scanning electron microscopy (FESEM). The amount of SiO2 in the coating was determined by energy-dispersive analysis of x-ray (EDX), and the crystalline structure of the coating was examined by x-ray diffractometer (XRD). All the experiments concerning the corrosion behavior of the coating carried out in 3.5 wt.% NaCl solution and evaluated by electrochemical impedance spectroscopy (EIS) and polarization technique. The results showed that an incorporation of SiO2 and Al2O3 in Ni-P coating at the SiO2 concentration of 10 g/Land 14 g/LAl2O3 led to the lowest corrosion rate ( i corr = 1.3 µA/cm2), the most positive E corr and maximum microhardness (496 VH). Furthermore, Ni-P-SiO2-Al2O3 nano-composite coating possesses less porosity than that in Ni-P coating, resulting in improving corrosion resistance.

Effects of the Buffer Layers on the Adhesion and Antimicrobial Properties of the Amorphous ZrAlNiCuSi Films

Science.gov (United States)

Chiang, Pai-Tsung; Chen, Guo-Ju; Jian, Sheng-Rui; Shih, Yung-Hui

2011-06-01

To extend the practical applications of the bulk metallic glasses (BMGs), the preparation of the metallic glass coatings on various substrates becomes an important research issue. Among the interfacial properties of the coatings, the adhesion between films and substrates is the most crucial. In this study, amorphous Zr61Al7.5Ni10Cu17.5Si4 (ZrAlNiCuSi) thin films were deposited on SUS304 stainless steel at various sputtering powers by DC sputtering. According to the scratch tests, the introduction of the Cr and Ti buffer layers effectively improves the adhesion between the amorphous thin films and substrate without changing the surface properties, such as roughness and morphology. The antimicrobial results show that the biological activities of these microbes, except Acinetobacter baumannii, are effectively suppressed during the test period.

Effect of consolidation techniques on the properties of Al matrix composite reinforced with nano Ni-coated SiC

Science.gov (United States)

Abolkassem, Shimaa A.; Elkady, Omayma A.; Elsayed, Ayman H.; Hussein, Walaa A.; Yehya, Hosam M.

2018-06-01

Al /Ni-SiC composite was prepared via powder metallurgy technique. SiC particles were coated with 10 wt% nano nickel by electroless deposition, then mixed by three percents (5, 10 and 15 wt%) with Al powder in a ball mill using 10:1 ball to powder ratio for 5 h. Three types of sintering techniques were used to prepare the composite. Uniaxial cold compacted samples were sintered in a vacuum furnace at 600 °C for 1 h. The second group was the vacuum sintered samples which were post-processed by hot isostatic press (HIP) at 600 °C for 1hr under the pressure of 190 MPa. The third group was the hot pressed samples that were consolidated at 550 °C under the uniaxial pressure of 840 MPa. The results showed that the hot pressed samples have the highest densification values (97-100%), followed by the HIP samples (94-98%), then come the vacuum sintered ones (92-96%). X-ray diffraction analysis (XRD) indicated the presence of Al and Al3Ni, which means that all SiC particles were encapsulated with nickel as short peaks for SiC were observed. Hardness results revealed that HIP samples have the highest hardness values. The magnetization properties were improved by increasing SiC/Ni percent, and HIP samples showed the highest magnetization parameter values.

Ternary systems Sr-{Ni,Cu}-Si: Phase equilibria and crystal structure of ternary phases

International Nuclear Information System (INIS)

Nasir, Navida; Melnychenko-Koblyuk, Nataliya; Grytsiv, Andriy; Rogl, Peter; Giester, Gerald; Wosik, Jaroslaw; Nauer, Gerhard E.

2010-01-01

Phase relations were established in the Sr-poor part of the ternary systems Sr-Ni-Si (900 deg. C) and Sr-Cu-Si (800 deg. C) by light optical microscopy, electron probe microanalysis and X-ray diffraction on as cast and annealed alloys. Two new ternary compounds SrNiSi 3 (BaNiSn 3 -type) and SrNi 9-x Si 4+x (own-type) were found in the Sr-Ni-Si system along with previously reported Sr(Ni x Si 1-x ) 2 (AlB 2 -type). The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type. At higher Si-content X-ray Rietveld refinements reveal the formation of a vacant site (□) corresponding to a formula SrNi 5.5 Si 6.5 □ 1.0 . Phase equilibria in the Sr-Cu-Si system are characterized by the compounds SrCu 2-x Si 2+x (ThCr 2 Si 2 -type), Sr(Cu x Si 1-x ) 2 (AlB 2 -type), SrCu 9-x Si 4+x (0≤x≤1.0; CeNi 8.5 Si 4.5 -type) and SrCu 13-x Si x (4≤x≤1.8; NaZn 13 -type). The latter two structure types appear within a continuous solid solution. Neither a type-I nor a type-IX clathrate compound was encountered in the Sr-{Cu,Ni}-Si systems. Structural details are furthermore given for about 14 new ternary compounds from related alloy systems with Ba. - Graphical abstract: The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type and is related to CeNi 8.5 Si 4.5 -type.

Tratamiento con inmunoterapia específica en niños con Rinitis Alérgica y/o Asma Bronquial. Área Norte. 2005 - 2007.

OpenAIRE

Matilde Iraida Morera Franco; Rigoberto Antonio García Chang; María Mercedes Gómez Paz

2007-01-01

Se realizó un estudio descriptivo longitudinal durante el período Enero 2005_ Enero 2007 en el Policlínico Norte del municipio Sancti Spíritus. El universo estuvo constituido por el total de niños con edades de 2_15 años con enfermedades alérgicas, a los que se realizó pruebas de alergia e indicó tratamiento con inmunoterapia específica por vía subcutánea, la muestra estuvo formada por 75 pacientes con asma bronquial, rinitis alérgica y/o ambas enfermedades, con el objetivo de determinar ...

Effect of Ni/Al2O3-SiO2 and Ni/Al2O3-SiO2 with K2O Promoter Catalysts on H2, CO and CH4 Concentration by CO2 Gasification of Rosa Multiflora Biomass

Directory of Open Access Journals (Sweden)

Tursunov Obid

2017-11-01

Full Text Available The thermal behaviour of the Rosa mutiflora biomass by thermogravimetric analysis was studied at heating rate 3 K min−1 from ambient temperature to 950 °C. TGA tests were performed in high purity carbon dioxide (99 998% with a flow rate 200 ml/min and 100 mg of sample, milled and sieved to a particle size below 250 µm. Moreover, yields of gasification products such as hydrogen (H2, carbon monoxide (CO and methane (CH4 were determined based on the thermovolumetric measurements of catalytic (Ni/Al2O3-SiO2 and Ni/Al2O3-SiO2 with K2O promoter catalysts and non-catalytic gasification of the Rosa multiflora biomass. Additionally, carbon conversion degrees are presented. Calculations were made of the kinetic parameters of carbon monoxide and hydrogen formation reaction in the catalytic and non-catalytic CO2 gasification processes. A high temperature of 950 °C along with Ni/Al2O3-SiO2and Ni/Al2O3-SiO2 with K2O promoter catalysts resulted in a higher conversion of Rosa multiflora biomass into gaseous yield production with greatly increasing of H2 and CO contents. Consequently, H2 and CO are the key factors to produce renewable energy and bio-gases (synthesis gas. The parameters obtained during the experimental examinations enable a tentative assessment of plant biomasses for the process of large-scale gasification in industrial sectors.

Study of Ti/Si/Ti/Al/Ni/Au ohmic contact for AlGaN/GaN HEMT

Science.gov (United States)

Shostachenko, S. A.; Porokhonko, Y. A.; Zakharchenko, R. V.; Burdykin, M. S.; Ryzhuk, R. V.; Kargin, N. I.; Kalinin, B. V.; Belov, A. A.; Vasiliev, A. N.

2017-12-01

This paper is dedicated to the experimental investigation of Ohmic contacts to the n+-doped region of AlGaN/GaN transistor heterostructure based on Ti/Si/Ti/Al/Ni/Au metallization. Effect of annealing temperature on the specific resistance of Ohmic contact was studied. Ohmic contact with the resistance of 3.4·10-6 Ω·cm2 was formed by optimization of the annealing temperature and introduction of the additional doping silicon layer.

Preparation, mechanical strengths, and thermal stability of Ni-Si-B and Ni-P-B amorphous wires

International Nuclear Information System (INIS)

Inoue, A.; Furukawa, S.; Hagiwara, M.; Masumoto, T.

1987-01-01

Ni-based amorphous wires with good bending ductility have been prepared for Ni/sub 75/Si/sub 8/B/sub 17/ and Ni/sub 78/P/sub 12/B/sub 10/ alloys containing 1 to 2 at. pct Al or Zr by melt spinning in rotating water. The enhancement of the wire-formation tendency by the addition of Al has been clarified to be due to the increase in the stability of the melt jet through the formation of a thin Al/sub 2/O/sub 3/ film on the outer surface. The maximum wire diameter is about 190 to 200 μm for the Ni-Si (or P)-B-Al alloys and increases to about 250 μm for the Ni-Si-B-Al-Cr alloys containing 4 to 6 at. pct Cr. The tensile fracture strength and fracture elongation are 2730 MPa and 2.9 pct for (N/sub 0.75/Si/sub 0.08/B/sub 0.17/)/sub 99/Al/sub 1/ wire and 2170 MPa and 2.4 pct for (Ni/sub 0.78/P/sub 0.12/B/sub 0.1/)/sub 99/Al/sub 1/ wire. These wires exhibit a fatigue limit under dynamic bending strain in air with a relative humidity of 65 pct; this limit is 0.50 pct for a NiSi-B-Al wire, which is higher by 0.15 pct than that of a Fe/sub 75/Si/sub 10/B/sub 15/ amorphous wire. Furthermore, the Ni-base wires do not fracture during a 180-deg bending even for a sample annealed at temperatures just below the crystallization temperature, in sharp contrast to high embrittlement tendency for Fe-base amorphous alloys. Thus, the Ni-based amorphous wires have been shown to be an attractive material similar to Fe- and Co-based amorphous wires because of its high static and dynamic strength, high ductility, high stability to thermal embrittlement, and good corrosion resistance

Evaluación del peso al nacer en 92 niños con fisuras del labio y del paladar

Directory of Open Access Journals (Sweden)

Carlos Evaristo Zamora Linares

Full Text Available Objetivo: describir y evaluar algunos aspectos relacionados con el peso al nacer en una población de niños con fisuras de labio y paladar. Métodos: estudio descriptivo con fase analítica realizado en el Hospital Pediátrico Provincial "Hermanos Cordové", de Manzanillo, Cuba. Se incluyeron, luego de ser seleccionados por conveniencia, 92 niños nacidos con fisuras bucales que fueron atendidos en el centro entre los años 1986 y 2010. Se consideraron las variables siguientes: sexo, peso al nacer y tipo de fisura. Mediante medidas descriptivas se establecen asociaciones intervariables. Los aspectos analíticos incluyen el análisis de varianza y la estimación de riesgo (odds ratio y su intervalo de confianza del 95 %. Resultados: la prevalencia de bajo peso al nacer en estos pacientes (14,1 % resultó elevada, en comparación con la población general. Hubo una asociación significativa entre el tipo de fisura y el peso al nacer (X²= 12,65. El riesgo de bajo peso al nacer en los pacientes con fisuras labiales asociadas a fisuras palatinas fue significativo (RP= 6,24; IC 95 %: 1,3-30. Conclusiones: los resultados del estudio se corresponden de manera general con los obtenidos por otros autores. Aparentemente hay una asociación entre el nivel de gravedad de las fisuras y el riesgo de bajo peso al nacer.

Gd-Ni-Si system

International Nuclear Information System (INIS)

Bodak, O.I.; Shvets, A.F.

1983-01-01

By X-ray phase analysis method isothermal cross section of phase diagram of the Gd-Ni-Si system at 870 K is studied. The existence of nine previously known compounds (GdNisub(6.72)Sisub(6.28), GdNi 10 Si 2 , GdNi 5 Si 3 , GdNi 4 Si, GdNi 2 Si 2 , GdNiSi 3 , GdNiSi 2 , Gd 3 Ni 6 Si 2 and GdNiSi) is confirmed and three new compounds (GdNisub(0.2)Sisub(1.8), Gdsub(2)Nisub(1-0.8)Sisub(1-1.2), Gd 5 NiSi 4 ) are found. On the base of Gd 2 Si 3 compound up to 0.15 at. Ni fractions, an interstitial solid solution is formed up to 0.25 at Ni fractions dissolution continues of substitution type. The Gd-Ni-Si system is similar to the Y-Ni-Si system

Characterization of Ni-P-SiO{sub 2}-Al{sub 2}O{sub 3} nanocomposite coatings on aluminum substrate

Energy Technology Data Exchange (ETDEWEB)

Rahemi Ardakani, S., E-mail: saeed.rahemi69@gmail.com [Department of Materials Science and Engineering, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Afshar, A. [Department of Materials Science and Engineering, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Sadreddini, S., E-mail: sina.sadreddini1986@gmail.com [Young Researchers and Elites Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Ghanbari, A.A. [Department of Materials Science and Engineering, Sharif University of Technology, International Campus, Kish Island (Iran, Islamic Republic of)

2017-03-01

In the present work, nano-composites of Ni-P-SiO{sub 2}-Al{sub 2}O{sub 3} were coated on a 6061 aluminum substrate. The surface morphology of the nano-composite coating was studied by field emission scanning electron microscopy (FESEM). The amount of SiO{sub 2} in the coating was determined by Energy Dispersive Analysis of X-Ray (EDX) and the crystalline structure of the coating was examined by X-ray diffractometer (XRD). All the experiments concerning the corrosion behavior of the coating carried out in 3.5%wt NaCl solution and evaluated by electrochemical impedance spectroscopy (EIS) and polarization technique. The results showed that an incorporation of SiO{sub 2} and Al{sub 2}O{sub 3} in Ni-P coating at the SiO{sub 2} concentration of 10 g/L and 14 g/L Al{sub 2}O{sub 3} led to the lowest corrosion rate (i{sub corr} = 0.88 μA/cm{sup 2}), the most positive E{sub corr} and maximum microhardness (537 μHV). Furthermore, increasing the amount of nanoparticles in the coating was found to decrease CPE{sub dl} and improve porosity. - Highlights: • The maximum content of Al{sub 2}O{sub 3} and SiO{sub 2} in the coating was increased to 14.02%wt and 4.54%wt, respectively. • By enhancing the amount of nanoparticles in the coating, there was higher corrosion resistance. • Increasing the nanoparticles content in the coating improved microhardness of coating. • The maximum of microhardness of Ni-P-SiO{sub 2}-Al{sub 2}O{sub 3} was measured to be 537 μHV.

Effect of Heat Treatment on Morphology of Fe-Rich Intermetallics in Hypereutectic Al-Si-Cu-Ni Alloy with 1.26 pct Fe

Science.gov (United States)

Sha, Meng; Wu, Shusen; Wan, Li; Lü, Shulin

2013-12-01

Cobalt is generally considered as the element that can neutralize the negative effects of iron in Al alloys, such as inducing fracture and failure for stress concentration. Nevertheless, Fe-rich intermetallics would be inclined to form coarse plate-like δ-Al4(Fe, Co, Ni)Si2 particles when the content of Fe was high, which could also cause inferior mechanical properties. The dissolution and transformation of δ-Al4(Fe, Co, Ni)Si2 phase in solution heat-treated samples of Al-20Si-1.85Cu-1.05Ni-1.26Fe-1.35Co alloy were studied using optical microscopy, image analysis, and scanning electron microscopy. The effects of solution heat treatment time ranging from 0 to 9 hours at 783.15 K (510 °C) on mechanical properties were also investigated. The coarse plate-like δ-Al4(Fe, Co, Ni)Si2 particles varied slowly through concurrent dissolution along widths and at the plate tips as solution treatment time increased, which could be explained from diffusion-induced grain boundary migration. Solution heat treatment also has an important influence on mechanical properties. The maximum ultimate tensile strength and yield strength after T6 treatment were 258 and 132 MPa, respectively, while the maximum hardness was 131 HB. Compared with those of the samples in the as-cast state, they increased by 53, 42, and 28 pct, respectively. Moreover, δ-Al4(Fe, Co, Ni)Si2 phase, which appears as a coarse plate-like particle in two dimensions, is actually a cuboid in three dimensions. The length of this cuboid is close to the width, while the height is much smaller.

Correlation between stresses and adhesion of oxide scales on Si and Ti containing NiCrAlY alloys

International Nuclear Information System (INIS)

Vosberg, V.; Quadakkers, W.J.; Schubert, F.; Nickel, H.

1998-09-01

The relation between mechanical stresses and the adhesion of alumina scales on Si- and Ti-containing NiCrAlY alloys has been investigated. Therefore the Si and Ti contents in model alloys with the base composition Ni-20Cr-10Al-Y, which were cast to achieve high purity, were varied from 0 to 2 m/0 . These solid samples were subjected to cyclic oxidation in the temperature range from 950 to 1100 C. Growth and spallation of the oxide scale were observed by gravimetry. The stresses, present at ambient temperature, were periodically determined by X-ray stress evaluation. Using these results a reasoning of the mechanisms for stress relief and damage of the scale was carried out. The addition of Silicon as well as of titanium has an evident influence on phase composition of Ni-20Cr-10Al-Y type alloys. Due to the variation of phase stability regions the thermal expansion is affected by these additions in the range from 950 to 1100 C. The expansion is enlarged by the addition of Si and lowered with increasing Ti content. (orig.)

Assessment of AlSi21CuNi Alloy’s Quality with Use of ATND Method

Directory of Open Access Journals (Sweden)

Pezda J.

2013-12-01

Full Text Available Majority of combustion engines is produced (poured from Al-Si alloys with low thermal expansion coefficient, so called piston silumins. Hypereutectic alloys normally contain coarse, primary angular Si particles together with eutectic Si phase. The structure and mechanical properties of these alloys are highly dependent upon cooling rate, composition, modification and heat-treatment operations. In the paper one depicts use of the ATND method (thermal-voltage-derivative analysis and regression analysis to assessment of quality of the AlSi21CuNi alloy modified with Cu-P on stage of its preparation, in aspect of obtained mechanical properties (R0,02, Rm, A5, HB. Obtained dependencies enable prediction of mechanical properties of the investigated alloy in laboratory conditions, using values of characteristic points from curves of the ATND method.

Laser alloying of AI with mixed Ni, Ti and SiC powders

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-03-01

Full Text Available composite (MMC) is formed. The MMC layer has excellent hardness and wear resistance compared to the base alloy [9-13]. Man et al. [14] used a high power continuous wave Nd:YAG laser to alloy aluminium AA 6061 with preplaced NiTi (54 wt% Ni & 46 wt...Al, Ti3Al, SiC, Al and Si phases. The hardness increased from 75HV to 650HV due to the formation of the TiC particles and TiAl and Ti3Al intermetallics. Su and Lei [9] laser cladded Al-12wt%Si with a powder containing SiC and Al-12wt%Si in a 3...

Variaciones del perfil lipídico en pacientes pediátricos con desnutrición

OpenAIRE

Gerardo Fernando Fernández Soto; Jean Carlos Quintero Nieto; Elsa Verónica Troya Ortiz; Carolina Arráiz de Fernández; Tania Beatriz Romero Adrian

2017-01-01

La desnutrición infantil se registra como uno de los principales problemas de salud pública de América Latina; pues es una de las mayores causas de mortalidad y morbilidad evitable en los niños y niñas de Latinoamérica. Adicional al problema de la alta prevalencia de la desnutrición infantil, son motivo de gran preocupación las consecuencias que la desnutrición deja en los niños que la sufren; ya que los niños con desnutrición en los primeros años de vida tienen mayor riesgo de sufrir enferme...

Influence of Al addition on phase transformation and thermal stability of nickel silicides on Si(0 0 1)

International Nuclear Information System (INIS)

Huang, Shih-Hsien; Twan, Sheng-Chen; Cheng, Shao-Liang; Lee, Tu; Hu, Jung-Chih; Chen, Lien-Tai; Lee, Sheng-Wei

2014-01-01

Highlights: ► The presence of Al slows down the Ni 2 Si–NiSi phase transformation but significantly promotes the NiSi 2−x Al x formation. ► The behavior of phase transformation strongly depends on the Al concentration of the initial Ni 1−x Al x alloys. ► The Ni 0.91 Al 0.09 /Si system exhibits remarkably improved thermal stability, even after high temperature annealing for 1000 s. ► The relationship between microstructures, electrical property, and thermal stability of Ni(Al) silicides is discussed. -- Abstract: The influence of Al addition on the phase transformation and thermal stability of Ni silicides on (0 0 1)Si has been systematically investigated. The presence of Al atoms is found to slow down the Ni 2 Si–NiSi phase transformation but significantly promote the NiSi 2−x Al x formation during annealing. The behavior of phase transformation strongly depends on the Al concentration of the initial Ni 1−x Al x alloys. Compared to the Ni 0.95 Pt 0.05 /Si and Ni 0.95 Al 0.05 /Si system, the Ni 0.91 Al 0.09 /Si sample exhibits remarkably enhanced thermal stability, even after high temperature annealing for 1000 s. The relationship between microstructures, electrical property, and thermal stability of Ni silicides is discussed to elucidate the role of Al during the Ni 1−x Al x alloy silicidation. This work demonstrated that thermally stable Ni 1−x Al x alloy silicides would be a promising candidate as source/drain (S/D) contacts in advanced complementary metal–oxide-semiconductor (CMOS) devices

Microstructure, Wear Resistance and Oxidation Behavior of Ni-Ti-Si Coatings Fabricated on Ti6Al4V by Laser Cladding

Directory of Open Access Journals (Sweden)

Qiaoqiao Zhuang

2017-10-01

Full Text Available The Ni-Ti-Si composite coatings were successfully fabricated on Ti6Al4V by laser cladding. The microstructure were studied by SEM (scanning electron microscopy and EDS (energy dispersive spectrometer. It has been found that Ti2Ni and Ti5Si3 phases exist in all coatings, and some samples have TiSi2 phases. Moreover, due to the existence of these phases, coatings presented relatively higher microhardness than that of the substrate (826 HV (Vickers hardness and the microhardness value of coating 3 is about twice larger than that of the substrate. During the dry sliding friction and wear test, due to the distribution of the relatively ductile phase of Ti2Ni and reinforcement phases of Ti5Si3 and TiSi2, the coatings performed good wear resistance. The oxidation process contains two stages: the rapid oxidation and slow oxidation by high temperature oxidation test at 800 °C for 50 h. Meanwhile, the value of the oxidation weight gain of the substrate is approximately three times larger than that of the coating 4. During the oxidation process, the oxidation film formed on the coating is mainly consisted of TiO2, Al2O3 and SiO2. Phases Ti2Ni, Ti5Si3, TiSi2 and TiSi were still found and it could be responsible for the improvement in oxidation resistance of the coatings by laser cladding.

First-principle investigations of the magnetic properties and possible martensitic transformation in Ni2MnX (X=Al, Ga, In, Si, Ge and Sn)

International Nuclear Information System (INIS)

Wang, Wei; Gao, She-Sheng; Meng, Yang

2014-01-01

The magnetic and electronic properties of Ni 2 MnX (X=Al, Ga, In, Si, Ge and Sn) Heusler alloys have been studied by using the first-principle projector augmented wave potential within the generalized gradient approximation. The possible non-modulated martensitic transformation in these six alloys has been investigated. Both austenitic and martensitic Ni 2 MnX (X=Al, Ga, In, Si, Ge and Sn) Heusler alloys are found to be ferromagnets. In martensitic phase, the energies minimum occurs at c/a=0.99 for Ni 2 MnX (X=Al, In, Ge and Sn), and the energy minimum occurs at c/a=1.02 for Ni 2 MnSi. But there is a negligible energy difference ΔE (<6 meV/cell) between the austenitic and martensitic phases for each alloy. Meanwhile, around c/a=1, an anomaly is observed in the E-c/a curve, which is related to a very slightly tetragonal distortion trend in Ni 2 MnX (X=Al, In, Si, Ge and Sn). The energy difference ΔE between the austenitic and martensitic phases for Ni 2 MnGa is as large as 99 meV/cell, so it is more likely to realize martensitic transformation in it. - Highlights: • Both austenitic and martensitic Ni 2 MnX alloys are found to be ferromagnets. • The energy difference between the martensitic and austenitic phases is negligible. • The total moment in martensitic phase is close to corresponding to austenitic phase

Study of the ternary alloy systems Al-Ni-Fe and Al-Cu-Ru with special regard to quasicrystalline phases

International Nuclear Information System (INIS)

Lemmerz, U.

1996-07-01

Two ternary alloy-systems, the Al-Ni-Fe system and the Al-Cu-Ru system were studied with special regard to quasicrystalline phases. Isothermal sections were established in both systems in the stoichiometric area of the quasicrystalline phase. In the Al-Ni-Fe system a new stable decagonal phase was found. Its stoichiometric range is very small around Al 71.6 Ni 23.0 Fe 5.4 . The temperature range in which it is stable lies between 847 and 930 C. The decagonal phase undergoes a eutectoid reaction to the three crystalline phases Al 3 Ni 2 , Al 3 Ni and Al 13 Fe 4 at 847 C. It melts peritectically at 930 C forming Al 13 Fe 4 , Al 3 Ni 2 and a liquid. The investigations in the Al-Cu-Ru system concentrated on the phase equilibria between the icosahedral phase and its neighbouring phases in a temperature range between 600 and 1000 C. The icosahedral phase was observed in the whole temperature range. The investigated stoichiometric area extends down to Al contents of 45%, which allows the fields of existence to be determined for the ternary phases α-AlCuRu, the icosahedral phase and Al 7 Cu 2 Ru. Binary phases were determined down to the upper (high Al content) border of AlRu. No hitherto unknown phase was observed in the investigated area. Rietveld analyses were carried out on α-AlCuRu and Al 7 Cu 2 Ru showing some discrepancies from the α-AlMnSi structure taken as a base for α-AlCuRu and confirming the Al 7 Cu 2 Fe structure for Al 7 Cu 2 Ru. (orig.)

An electrochemical investigation of the corrosion behavior of Al-Si-Cu hypereutectic alloys in alcoholic environments

Directory of Open Access Journals (Sweden)

Traldi, S. M.

2003-12-01

Full Text Available Al-Si-Cu hypereutetic alloys produced by spray forming are mostly used in the automotive industry, especially for cylinder liners. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties - mainly wear resistance at high temperatures. The corrosion resistance of these alloys in fuels, particularly alcoholic media, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS and potentiodynamic polarisation have been used to evaluate the corrosion resistance of a hypereutectic Al-Si-Cu alloy in alcoholic environments. The EIS tests were carried out in pure ethanol, and ethanol with small additions (1 mM of acid and chloride, to investigate the effect of these contaminants on corrosion resistance. The corrosion resistance of a grey cast iron has also been evaluated in pure ethanol for comparison. The Al-Si-Cu alloy showed high corrosion resistance in pure ethanol, far superior to that of grey cast iron in the same medium.

Aleaciones hipereutécticas producidas por conformación por spray son muy empleadas en la industria automovilística, especialmente en los revestimientos de los cilindros. Tienen la ventaja de añadir menos peso con bajo coeficiente de expansión térmica y excelentes propiedades mecánicas, sobre todo resistencia al desgaste en altas temperaturas. Todavía, la resistencia a la corrosión de estas aleaciones en combustibles no es conocida. En este estudio fueron utilizadas las técnicas de espectroscopia de impedancia electroquímica y polarización potenciodinámica, para evaluar la resistencia a la corrosión de una aleación hipereutéctica Al-Si-Cu en medio alcohólico. Las pruebas fueron conducidas en etanol puro y etanol con pequeñas adiciones (1 mM de ácido y cloruro, con la finalidad de investigar el efecto de estos contaminantes en la resistencia a la corrosión. Hierro fundido gris, también fue

Gingivitis y Anticuerpos Anticitoplasmáticos de Neutrófilos en niños y adolescentes con leucemia

OpenAIRE

Viera, Ninoska; Rojas de Morales, Thais; Navas, Rita; Zambrano, Olga; Paz de Gudiño, Mercedes

2004-01-01

Introducción: Las enfermedades sistémicas pueden originar y exacerbar alteraciones en el periodonto. Se ha demostrado la presencia de Anticuerpos Anticitoplasmáticos de neutrófi los (ANCA) en pacientes con enfermedad periodontal destructiva y con enfermedades sistémicas. Objetivo: Determinar la re la ción entre gingivitis y los ANCA en niños y ado les cen tes con leucemia que asistieron al Servicio Autónomo Hospital Uni ver si ta rio de Maracaibo y a la Fundación del Hosp...

Pitting Corrosion of Ni3(Si,Ti+2Cr Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2014-05-01

Full Text Available The pitting corrosion of Ni3(Si,Ti with 2 at% Cr containing two regions of a Ni3(Si,Ti single-phase of L12 structure and a mixture phase of of (L12 +Niss was investigated as function of chloride concentrations by using a polarization method, scanning electron microscope and energy dispersive X-Ray spectroscopy in neutral sodium chloride solutions at 293 K.  The pitting corrosion of Ni3(Si,Ti with and without the addition of aluminium and type C276 alloy were also studied under the same experimental condition for the comparison.  The pitting potential obtained for the Ni3(Si,Ti with 2 at% Cr decreased with increasing chloride concentration.  The specific pitting potentials and the pitting potentials were decreased in the order of C276 alloy > Ni3(Si,Ti > Ni3(Si,Ti + 2Cr > Ni3(Si,Ti + 4Al, which means that the pitting corrosion resistance of Ni3(Si,Ti with 2 at% Cr was higher than Ni3(Si,Ti with 4 at% Al, but lower than that of Ni3(Si,Ti.  A critical chloride concentration of Ni3(Si,Ti with 2 at% Cr was found to be higher than that of Ni3(Si,Ti with at% Al. In addition, the presence of high concentration for oxygen indicates the occurrence of pit formation.

Study of microstructural evolution of X4CrNiSiTi14-7 during thermal aging; Untersuchung der mikrostrukturellen Entwicklung von X4CrNiSiTi14-7 waehrend thermischer Alterung

Energy Technology Data Exchange (ETDEWEB)

Sakhawat, Shahroz; Falahati, Ahmad [Vienna Univ. of Technology (Austria). Inst. of Materials Science and Technology; Domankova, Maria [MTF STU Trnava (Slovakia). Inst. of Materials Science

2010-09-15

Microstructural evolution during aging treatment in a high tensile precipitation hardening stainless steel (X4CrNiSiTi14-7) has been investigated. Matrix consists of martensitic structure and the combined addition of Si and Ti causes an intermetallic phase type Ni{sub 16}Ti{sub 6}Si{sub 7} that precipitates with-in grains and enhance precipitation strengthening. This material shows a good combination of high strength and ductility. Light-Optical microscopy, electron back scattered diffraction, transmission electron microscopy and X-ray diffraction analysis have been used to study the microstructural evolution during aging. It has been found that precipitations of various kinds are taking place during aging treatments including nm-scaled G-phase and various carbides. Higher aging temperatures lead to reverse transformation of martensite to austenite. (orig.)

Ductility of Ni3Al doped with substitutional elements

International Nuclear Information System (INIS)

Hanada, S.; Chiba, A.; Guo, H.Z.; Watanabe, S.

1993-01-01

This paper reports on ductility of B-free Ni 3 Al alloys. Recrystallized Ni 3 Al binary alloys with Ni-rich compositions show appreciable ductility when an environmental effect is eliminated, while the alloys with stoichiometric and Al-rich compositions remain brittle. The ductility in the Ni-rich Ni 3 Al alloys is associated with low ordering energy. The additions of ternary elements, which are classified as γ formers, ductilize ternary Ni 3 Al alloys(Ni-23 at% Al-2 at% X, X = Pd, Pt, Cu and Co), whereas the additions of γ' formers embrittle ternary Ni 3 Al alloys(Ni-23 at% Al-2 at% X, X = Ta, Mo, Nb, Zr, Hf, V, Ti and Si). The additions of small amounts (less than 1 at%) of γ' formers such as Zr and Hf also ductilize as-cast ternary Ni 3 Al alloys. Ductility of Ni 3 Al alloys doped with substitutional elements is discussed in terms of ordering energy and microstructure

El autoconcepto en niños con necesidades educativas especiales

OpenAIRE

Noemí Sabeh, Eliana

2002-01-01

En el presente artículo se desarrollan consideraciones teóricas acerca del autoconcepto y se analiza el efecto que diversos factores vinculados al desarrollo de niños con necesidades especiales pueden tener sobre la imagen de sí. Nos centramos posteriormente en los resultados de investigaciones actuales sobre autoconcepto en niños con discapacidad, refiriéndonos principalmente a niños con dificultades de aprendizaje, dado que son el grupo sobre el que se han realizado mayoritariamente los est...

Funcionalidad familiar relacionada al desarrollo psicomotor en niños de 2 y 3 años con desnutrición crónica que asisten al Wawa Wasi - Juliaca 2010.

OpenAIRE

Mamani Zapana, William Harold

2012-01-01

La presente investigación se realizó con el objetivo de Determinar el tipo de funcionalidad familiar que se relaciona con el desarrollo psicomotor de niños menores de 2 y 3 años con desnutrición crónica que asisten al Programa Nacional Wawa Wasi, Juliaca 2010. La investigación fue de tipo analítico transversal de diseño correlaciona! con metodología cuantitativa. La muestra de estudio estuvo conformada por 85 niños y niñas. El instrumento utilizado para medir la funcionalidad familiar fue el ...

Development of an efficient grain refiner for Al-7Si alloy

Energy Technology Data Exchange (ETDEWEB)

Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

2000-03-15

The response of Al-7Si alloy towards grain refinement by Al-Ti-B master alloys (with different Ti-B ratios) at different addition levels has been studied in detail. The results indicate that high B-containing master alloys are powerful grain refiners when compared to conventional grain refiners like Al-5Ti-lB master alloys. In the present study, indigenously developed master alloys have been used for the grain refinement of alloys Al-7Si and LM-25. Significant improvements in mechanical properties have been obtained with a combination of grain refiner and Sr as modifier. (orig.)

Constituent phase diagrams of the Al-Cu-Fe-Mg-Ni-Si system and their application to the analysis of aluminium piston alloys

Energy Technology Data Exchange (ETDEWEB)

Belov, N.A. [Moscow Institute of Steel and Alloys, Leninsky prosp. 4, Moscow 119049 (Russian Federation); Eskin, D.G. [Netherlands Institute for Metals Research, Rotterdamseweg 137, 2628AL Delft (Netherlands)]. E-mail: deskin@nimr.nl; Avxentieva, N.N. [Moscow Institute of Steel and Alloys, Leninsky prosp. 4, Moscow 119049 (Russian Federation)

2005-10-15

The evaluation of phase equilibria in quinary systems that constitute the commercially important Al-Cu-Fe-Mg-Ni-Si alloying system is performed in the compositional range of casting alloys by means of metallography, electron probe microanalysis, X-ray diffractometry, differential scanning calorimetry, and by the analysis of phase equilibria in the constituent systems of lesser dimensionality. Suggested phase equilibria are illustrated by bi-, mono- and invariant solidification reactions, polythermal diagrams of solidification, distributions of phase fields in the solid state, and isothermal and polythermal sections. Phase composition of as-cast alloys is analyzed in terms of non-equilibrium solidification. It is shown that the increase in copper concentration in piston Al-Si alloys results in the decrease in the equilibrium solidus from 540 to 505 deg C. Under non-equilibrium solidification conditions, piston alloys finish solidification at {approx}505 deg C. Iron is bound in the quaternary Al{sub 8}FeMg{sub 3}Si{sub 6} phase in low-iron alloys and in the ternary Al{sub 9}FeNi and Al{sub 5}FeSi phases in high-iron alloys.

Investigations on Mechanical Behaviour of Micro Graphite Particulates Reinforced Al-7Si Alloy Composites

Science.gov (United States)

Nagaraj, N.; Mahendra, K. V.; Nagaral, Madeva

2018-02-01

Micro particulates reinforced metal matrix composites are finding wide range of applications in automotive and sports equipment manufacturing industries. In the present study, an attempt has been made to develop Al-7Si-micro graphite particulates reinforced composites by using liquid melt method. 3 and 6 wt. % of micro graphite particulates were added to the Al-7Si base matrix. Microstructural characterization was done by using scanning electron microscope and energy dispersive spectroscope. Mechanical behaviour of Al-7Si-3 and 6 wt. % composites were evaluated as per ASTM standards. Scanning electron micrographs revealed the uniform distribution of micro graphite particulates in the Al-7Si alloy matrix. EDS analysis confirmed the presence of B and C elements in graphite reinforced composites. Further, it was noted that ultimate tensile and yield strength of Al-7Si alloy increased with the addition of 3 and 6wt. % of graphite particulates. Hardness of graphite reinforced composites was lesser than the base matrix.

Respuesta al tapiz rodante y entrenamiento en niños con riesgo de retraso en el desarrollo motor

OpenAIRE

Valentín Gudiol, Marta

2014-01-01

El recién nacido prematuro y los bebés de bajo peso al nacer frecuentemente presentan retrasos/anomalías en el desarrollo motor, cognitivo y emocional(1). Son una población que será clasificada como niños con riesgo de retraso en el desarrollo psicomotor(2). Uno de los diagnósticos más frecuentes en esta población es el de parálisis cerebral (PC)(3), que suele establecerse a partir de los 12 meses de edad del niño(4). El tapiz rodante se ha utilizado en población pediátrica con diferentes dia...

Hot Corrosion Behavior of Stainless Steel with Al-Si/Al-Si-Cr Coating

Science.gov (United States)

Fu, Guangyan; Wu, Yongzhao; Liu, Qun; Li, Rongguang; Su, Yong

2017-03-01

The 1Cr18Ni9Ti stainless steel with Al-Si/Al-Si-Cr coatings is prepared by slurry process and vacuum diffusion, and the hot corrosion behavior of the stainless steel with/without the coatings is studied under the condition of Na2SO4 film at 950 °C in air. Results show that the corrosion kinetics of stainless steel, the stainless steel with Al-Si coating and the stainless steel with Al-Si-Cr coating follow parabolic laws in several segments. After 24 h corrosion, the sequence of the mass gain for the three alloys is the stainless steel with Al-Si-Cr coating coating coating. The corrosion products of the three alloys are layered. Thereinto, the corrosion products of stainless steel without coating are divided into two layers, where the outside layer contains a composite of Fe2O3 and FeO, and the inner layer is Cr2O3. The corrosion products of the stainless steel with Al-Si coating are also divided into two layers, of which the outside layer mainly consists of Cr2O3, and the inner layer is mainly SiO2. The corrosion film of the stainless steel with Al-Si-Cr coating is thin and dense, which combines well with substrate. Thereinto, the outside layer is mainly Cr2O3, and the inside layer is Al2O3. In the matrix of all of the three alloys, there exist small amount of sulfides. Continuous and protective films of Cr2O3, SiO2 and Al2O3 form on the surface of the stainless steel with Al-Si and Al-Si-Cr coatings, which prevent further oxidation or sulfide corrosion of matrix metals, and this is the main reason for the much smaller mass gain of the two alloys than that of the stainless steel without any coatings in the 24 h hot corrosion process.

Cuidador familiar del niño con cáncer: un rol en transición

OpenAIRE

Sonia Carreño-Moreno; Lorena Chaparro- Díaz; Paola Blanco-Sánchez

2017-01-01

El objetivo de este artículo es integrar los hallazgos derivados de investigación que evidencian que el ser cuidador de un niño con cáncer denota un rol en transición. La metodología que se empleó fue la revisión integrativa de literatura que incluyó la búsqueda sistemática de esta, una lectura crítica de las publicaciones, la integración de hallazgos con apoyo en Atlas Ti ver- sión 7, en un proceso de comparación constante. Pudo ¿verse que el cuidador del niño con cán - cer ...

Comportamiento a la corrosión electroquímica de aleaciones MgAl con recubrimientos de materiales compuestos Al/SiCp mediante proyección térmica

Directory of Open Access Journals (Sweden)

Pardo, A.

2010-04-01

Full Text Available The corrosion protection of Mg-Al alloys by flame thermal spraying of Al/SiCp composite coatings was evaluated by electrochemical impedance spectroscopy in 3.5 wt.% NaCl solution. The volume fraction of SiC particles (SiCp varied between 5 and 30%. The as-sprayed Al/SiCp composite coatings revealed a high number of micro-channels, largely in the vicinity of the SiC particles, that facilitated the penetration of the electrolyte and the subsequent galvanic corrosion of the magnesium substrates. The application of a cold-pressing post-treatment reduced the degree of porosity of the coatings and improved the bonding at the coating/substrate and Al/SiC interfaces. This resulted in improved corrosion resistance of the coated specimens. The effectiveness of the coatings slightly decreased with the addition of 5-30 vol.% SiCp compared with the unreinforced thermal spray aluminium coatings.

Se estudia, mediante espectroscopía de impedancia electroquímica en solución 3,5 % NaCl, la protección frente a la corrosión de aleaciones Mg-Al recubiertas por proyección térmica con materiales compuestos Al/SiCp. Se varió la fracción de volumen de las partículas de SiC (SiCp entre 5 y 30 %. Los recubrimientos efectuados por proyección térmica revelan un elevado número de microcanales, en la vecindad de las partículas de SiC, que facilitan la penetración del electrolito originando procesos de corrosión galvánica en los substratos de las aleaciones de magnesio. Un tratamiento posterior mediante la aplicación de una presión en frío reduce el grado de porosidad de los recubrimientos y mejora la unión, tanto entre el substrato y el recubrimiento como entre las partículas de aluminio y SiC, mejorando la resistencia a la corrosión de las aleaciones recubiertas. La efectividad de los recubrimientos disminuye ligeramente con la adición de SiCp cuando se comparan con los mismos recubrimientos de aluminio sin refuerzo.

Preparation and characterization of squeeze cast-Al–Si piston alloy reinforced by Ni and nano-Al2O3 particles

Directory of Open Access Journals (Sweden)

Hashem F. El-Labban

2016-07-01

Full Text Available Al–Si base composites reinforced with different mixtures of Ni and nano-Al2O3 particles have been fabricated by squeeze casting and their metallurgical and mechanical characterization has been investigated. A mixture of Ni and nano-Al2O3 particles of different ratios was added to the melted Al–Si piston alloy at 700 °C and stirred under pressure. After the Al-base-nano-composites were fabricated by squeeze casting, the microstructure and the particle distribution inside the matrix have been investigated using optical and scanning electron microscopes. Moreover, the hardness and the tensile properties of the resulted Al-base-nano-composites were evaluated at room temperature by using Vickers hardness and universal tensile testers, respectively. As a result, in most cases, it was found that the matrix showed a fine eutectic structure of short silicon constituent which appeared in the form of islands in the α-phase around some added particle agglomerations of the nano-composite structures. The tendency of this structure formation increases with the increase of Ni particle addition. As the ratio of the added particles increases, the tendency of these particles to be agglomerated also increases. Regarding the tensile properties of the fabricated Al-base-nano-composites, ultimate tensile strength is increased by adding the Ni and nano-Al2O3 particles up to 10 and 2 wt.%, respectively. Moreover, the ductility of the fabricated composites is significantly improved by increasing the added Ni particles. The composite material reinforced with 5 wt.% Ni and 2 wt.% nano-Al2O3 particles showed superior ultimate tensile strength and good ductility compared with any other added particles in this investigation.

Estilos parentales en niños y niñas con TDAH

Directory of Open Access Journals (Sweden)

Rocío González

2014-01-01

Full Text Available Introducción: el Trastorno por Déficit de Atención e Hiperactividad (TDAH es una de las alteraciones neuroconductuales más frecuentes en la infancia. La disfuncionalidad familiar es una variable de riesgo sobre la evolución de los síntomas. El objetivo fue analizar y comparar los estilos parentales en niños con y sin TDAH. Metodología: diseño expo facto con dos grupos, uno cuasi control. Se aplicaron dos escalas que evalúan estilos parentales. Resultados: tanto los niños con TDAH como sus padres perciben al estilo parental más rígido e indulgente y menos inductivo, caracterizado por una tendencia a manifestar mayor crítica y menor aceptación y afectuosidad por parte de los padres. Conclusiones: los hallazgos permiten el desarrollo de técnicas efectivas de disciplina y comunicación en la intervención clínica con familias de niños con TDAH.

Calidad de vida relacionada con la salud del niño y del adolescente con obesidad

OpenAIRE

Hurtado-Valenzuela, Jaime Gabriel; Álvarez-Hernández, Gerardo

2014-01-01

Objetivo Estimar la calidad de vida relacionada con la salud (CVRS) en un grupo de niños y adolescentes con obesidad de la ciudad de Hermosillo, Sonora, México. Métodos Se realizó un estudio transversal utilizando el cuestionario PedsQL® para comparar la CVRS de 200 niños y adolescentes con obesidad al igual que a sus padres, con dos grupos de control, uno de la comunidad (n=400) y otro grupo de usuarios (n=200) del Hospital Infantil del Estado de Sonora. Las diferencias en la CVRS fueron eva...

Synthesis, microstructure and magnetic properties of Fe{sub 3}Si{sub 0.7}Al{sub 0.3}@SiO{sub 2} core–shell particles and Fe{sub 3}Si/Al{sub 2}O{sub 3} soft magnetic composite core

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian, E-mail: snove418562@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Fan, Xi’an, E-mail: groupfxa@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Wu, Zhaoyang, E-mail: wustwuzhaoyang@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Li, Guangqiang [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan, Hubei 430081 (China)

2015-11-15

Fe{sub 3}Si{sub 0.7}Al{sub 0.3}@SiO{sub 2} core–shell particles and Fe{sub 3}Si/Al{sub 2}O{sub 3} soft magnetic composite core have been synthesized via a modified stöber method combined with following high temperature sintering process. Most of conductive Fe{sub 3}Si{sub 0.7}Al{sub 0.3} particles could be uniformly coated by insulating SiO{sub 2} using the modified stöber method. The Fe{sub 3}Si{sub 0.7}Al{sub 0.3}@SiO{sub 2} core–shell particles exhibited good soft magnetic properties with low coercivity and high saturation magnetization. The reaction 4Al+3SiO{sub 2}=2α-Al{sub 2}O{sub 3}+3Si took place during the sintering process. As a result the new Fe{sub 3}Si/Al{sub 2}O{sub 3} composite was formed. The Fe{sub 3}Si/Al{sub 2}O{sub 3} composite core displayed more excellent soft magnetic properties, better frequency stability at high frequencies, much higher electrical resistivity and lower core loss than the pure Fe{sub 3}Si{sub 0.7}Al{sub 0.3} core. The method of introducing insulating layers surrounding magnetic particles provides a promising route to develop new and high compact soft magnetic materials with good magnetic and electric properties. - Graphical abstract: In Fe{sub 3}Si/Al{sub 2}O{sub 3} composite, Fe{sub 3}Si phases are separated by Al{sub 2}O{sub 3} layers and the eddy currents are confined in Fe{sub 3}Si phases, thus increasing resistivity and reducing core loss. - Highlights: • Fe{sub 3}Si{sub 0.7}Al{sub 0.3}@SiO{sub 2} core–shell particles and Fe{sub 3}Si/Al{sub 2}O{sub 3} cores were prepared. • Fe{sub 3}Si{sub 0.7}Al{sub 0.3} particles could be uniformly coated by nano-sized SiO{sub 2} clusters. • Fe{sub 3}Si{sub 0.7}Al{sub 0.3}@SiO{sub 2} particles and Fe{sub 3}Si/Al{sub 2}O{sub 3} cores showed good soft magnetic properties. • Fe{sub 3}Si/Al{sub 2}O{sub 3} had lower core loss and better frequency stability than Fe{sub 3}Si{sub 0.7}Al{sub 0.3} cores.

Właściwości mechaniczne stopu AlSi7Mg modyfikowanego sodem

Directory of Open Access Journals (Sweden)

W. Orłowicz

2008-03-01

Full Text Available I'raca przcdstaivin ~vyniki bada6 wplywu rbwnoczcsncj mfinacji barbotahwvej argonem onz modyfikacji tytancm. horcm i sotlcm nnwtaSi7Mg. chlodzoncgo z rtnq szybkoiciq. Modelory-n odlewcm do badah byl odlcw klina wvykonnny tvformic piaskowej, zawierajqccj u podstawy wncki ochladzalni k. Dta occny szybkoici chlodzcnia poszczcgbtnych obs7arbw ottlcwu klinnw formic montowano tcmopary Ni-Cr-Ni. Po znlaniu for~nyc icklyrn mctalcrn zarejestrowano zrniany lcmpcmtuty w czesic, na podstawicktbrych oceniono sqbkoS6 cli todzcnin stopu w zakrcsic tcmpcratur likwidus-sotidus. Nastepnic odlcvy C;l ina poddnno obrhbcc cicplnci. Zodlewvfiw klinow z obszarciw, w ktbrych occninno zrniany Icmpcratury w czasic, vyciqto prbbki do badah rnctalognficznych omz prhbkido badai statycznej prhhy rozciqgania. Occniaoo paramctr strukturalny - odlegloSC pomi~dzyg al~ziarnid rndrytriw dnrgicgo rzqduFazy @(A[. IVykanano badania wytrzymaloici na rozciqgnnic, umowncj granicy plastyczno5ci orw. rtydluknia. Na podsrawic badahstviedzono, ;r:c uzyskmn nfi wysokoSci od lcwu mikros~rutture rbknila sic parametrcrn strukturalnym kD o pnad 3 razy. El'chcm u6inicowancjrnikms!ruktury bylo zrrjinicuwanic wtaiciwoici mcchanicznych.

Ni3Si surface-film formation caused by radiation-induced segregation

International Nuclear Information System (INIS)

Potter, D.I.; Rehn, L.E.; Okamoto, P.R.; Wiedersich, H.

1977-01-01

Several advanced alloys being considered for reactor applications contain the ordered γ' phase Ni 3 X in which the X component is frequently Al, Si and/or Ti. These alloys are precipitation hardened, and their strength depends upon the volume fraction, size, and spatial distribution of the coherent γ' precipitate. The investigation shows that a substantial Ni 3 Si precipitate film forms on the surface of irradiated specimens of solid-solution as well as two-phase Ni-Si alloys

Peso y talla en niños con retinoblastoma

Directory of Open Access Journals (Sweden)

Cecilia Ridaura-Sanz

2015-03-01

Full Text Available Introducción: la talla baja se ha descrito como característica clínica de niños con retinoblastoma. Esta particularidad puede estar relacionada directamente con la enfermedad de base o con factores externos.  Objetivo: el propósito de esta investigación fue conocer la frecuencia de talla y peso bajos en niños mexicanos con retinoblastoma y correlacionar los valores antropométricos con variables de la enfermedad y ambientales. Materiales y métodos: se analizaron expedientes clínicos de 346 pacientes con retinoblastoma. Se obtuvieron los datos de peso y talla referidos al ingreso; antes del tratamiento. Se comparó el valor de Z con las referencias de la distribución normal de la población mexicana. La asociación de las medidas antropométricas con las variables clínicas, sociales y genéticas se estableció con la prueba de c2. Resultados: la talla y el peso promedio de los niños con retinoblastoma fueron significativamente más bajos que los de la población general (p < 0.001 y p = 0.013, respectivamente. La talla y peso bajos fueron más frecuentes en niños con enfermedad avanzada, provenientes de medio rural y de bajo nivel socioeconómico. Conclusiones: los déficits en peso y talla en niños con retinoblastoma se deben a factores relacionados con enfermedad avanzada al momento del diagnóstico, lo cual a su vez es consecuencia de la situación de marginación de la población rural mexicana. Dado que la mayoría de las variables sociales y ambientales están muy relacionadas y que no podemos descartar posibles factores genéticos, las conclusiones de este estudio deben verificarse analizando las medidas de los padres y hermanos y establecer grupos comparativos para controlar las variables confusas.

El desarrollo del niño hasta los 12 meses. Orientaciones al pediatra para su vigilancia con la familia

Directory of Open Access Journals (Sweden)

Carmen Sánchez-Pérez

2015-11-01

Full Text Available El pediatra tiene un papel de primera importancia en la vigilancia y promoción del desarrollo de los niños; los padres estiman que es el profesional que puede orientarlos para saber si su desarrollo es normal y sobre la forma de proveer cuidados para favorecerlo. Para atender estas demandas el pediatra debe utilizar distintas herramientas que le permitan comprender la forma en que se va organizando el desarrollo del niño, pero a la vez la forma en que los cuidados, organización del ambiente y condiciones de riesgo y alarma pueden impactar en su evolución. No basta con aplicar pruebas de cribado, deben observarse además los procesos de crianza y la forma en qué aspectos del entorno pueden favorecer o limitar el desarrollo, acompañándose de recomendaciones claras que lo promuevan.  El objetivo primario de este artículo es llamar la atención del pediatra sobre la necesidad de asesorar a los padres sobre su capacidad para vigilar y favorecer el desarrollo normal y el cuidado de sus hijos en las actividades de la vida cotidiana. Señalamos aspectos del desarrollo susceptibles de ser observados regularmente y sobre los que se puede incidir mediante recomendaciones que modulen la relación con el niño. Exponemos una visión clínica del desarrollo infantil que permita, de manera sencilla, resolver las necesidades de los padres sobre cómo supervisar y conducir el desarrollo de sus hijos. Les proponemos complementar su evaluación con indicaciones y sugerencias para que aprendan a observar a sus hijos, siguiendo determinadas secuencias que de no cumplirse indican al pediatra una condición de riesgo y la necesidad de aplicar una prueba de tamizado completa otra de mayor especialización en la que se tenga experiencia.

Medidas directas e indirectas de las funciones ejecutivas en niños con trastorno de espectro autista

Directory of Open Access Journals (Sweden)

María Fernanda Pérez Pichardo

2018-01-01

Full Text Available INTRODUCCIÓN: los niños con trastorno del espectro autista (TEA tienen dificultades en las funciones ejecutivas (FE pero se han sugerido discrepancias entre las medidas directas e indirectas.   OBJETIVO: conocer si existen diferencias en las funciones ejecutivas mediante medidas directas e indirectas entre niños con y sin TEA.   MÉTODO: se incluyeron 14 varones entre primero y tercero de primaria, 50% con diagnóstico de TEA y 50% con desarrollo neurotípico, seleccionados por emparejamiento en edad y grado escolar. El promedio de edad de la muestra fue de 7.43 (DE 0.98 años. Se aplicaron las pruebas de Evaluación neuropsicológica de funciones ejecutivas en niños (ENFEN y el Inventario de clasificación comportamental de las funciones ejecutivas (BRIEF.   RESULTADOS: se encontraron diferencias significativas en las medidas de las FE indirectas, pero no en las directas, entre los grupos (p < 0.05. Así mismo, las correlaciones entre las medidas directas e indirectas fueron mayores en el grupo con TEA.   CONCLUSIONES: los niños con TEA son evaluados con más dificultades en las medidas indirectas de las funciones ejecutivas, pero obtienen puntuaciones similares a los niños con desarrollo neurotípico cuando son evaluados en condiciones estructuradas empleando medidas directas.

Microstructure and mechanical properties of Al-20Si-5Fe-2X (X = Cu, Ni, Cr) alloys produced by melt-spinning

International Nuclear Information System (INIS)

Rajabi, M.; Simchi, A.; Davami, P.

2008-01-01

Al-20Si-5Fe-2X (X = Cu, Ni and Cr) ribbons were produced by melt-spinning and consolidated by hot pressing at 400 deg. C for 60 min. The microstructure of the ribbons and the consolidated alloys was investigated using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffractometry (XRD) method, and transmission electron microscopy (TEM). The hardness and compressive strength of the specimens at ambient and elevated temperatures were examined. The microstructure of the ribbons exhibited featureless and dendritic zones. Results of XRD and TEM showed formation of spherically shaped Si particles with an average diameter of 20 nm. Ultrafine Si (110-150 nm) and iron-containing intermetallic particles were noticed in the microstructure of the consolidated ribbons. An improved strength was achieved by alloying of Al-20Si-5Fe with Cu, Ni, and Cr. Nickel was found to be the most effective element in increasing the maximum stress, particularly at elevated temperatures

Relación entre adherencia al tratamiento antirretroviral y subpoblaciones linfocitarias en niños con HIV/Sida

Directory of Open Access Journals (Sweden)

Jeannette Balbaryski

2013-08-01

Full Text Available El curso de la infección por HIV se caracteriza principalmente por una depleción grave de los linfocitos TCD4+ y una activación inmune marcada, hallazgos centrales que conducen a variaciones numéricas y fenotípicas de las poblaciones linfocitarias TCD4+. El tratamiento antirretroviral (TARV combinado ha modificado sustancialmente el curso de la infección por HIV, y la correcta adherencia al mismo resulta en una disminución de la carga viral a niveles indetectables, y a un incremento significativo en la repoblación de los linfocitos T periféricos. En este trabajo se evaluó en 28 niños HIV (+ la relación entre los cambios en los niveles de las poblaciones linfocitarias y la adherencia al TARV, luego de 9 meses en promedio de iniciado el mismo. El grupo de 18 niños con buena adherencia, superior al 95%, presentó un aumento significativo en los porcentajes de células naive CD4+CD45RA+CD62L+ y un descenso en las células de memoria central CD4+CD45RA-CD62L+, entre ambos momentos del seguimiento. Por el contrario, los 10 niños con fallas en la adherencia no mostraron diferencias significativas en los niveles de tales poblaciones. La buena adherencia al TARV produce el rápido y significativo descenso de la replicación viral lo cual se asocia a la progresiva reconstitución cuantitativa y funcional del sistema inmune.

U-Mo/Al-Si interaction: Influence of Si concentration

International Nuclear Information System (INIS)

Allenou, J.; Palancher, H.; Iltis, X.; Cornen, M.; Tougait, O.; Tucoulou, R.; Welcomme, E.; Martin, Ph.; Valot, C.; Charollais, F.; Anselmet, M.C.; Lemoine, P.

2010-01-01

Within the framework of the development of low enriched nuclear fuels for research reactors, U-Mo/Al is the most promising option that has however to be optimised. Indeed at the U-Mo/Al interfaces between U-Mo particles and the Al matrix, an interaction layer grows under irradiation inducing an unacceptable fuel swelling. Adding silicon in limited content into the Al matrix has clearly improved the in-pile fuel behaviour. This breakthrough is attributed to an U-Mo/Al-Si protective layer around U-Mo particles appeared during fuel manufacturing. In this work, the evolution of the microstructure and composition of this protective layer with increasing Si concentrations in the Al matrix has been investigated. Conclusions are based on the characterization at the micrometer scale (X-ray diffraction and energy dispersive spectroscopy) of U-Mo7/Al-Si diffusion couples obtained by thermal annealing at 450 deg. C. Two types of interaction layers have been evidenced depending on the Si content in the Al-Si alloy: the threshold value is found at about 5 wt.% but obviously evolves with temperature. It has been shown that for Si concentrations ranging from 2 to 10 wt.%, the U-Mo7/Al-Si interaction is bi-layered and the Si-rich part is located close to the Al-Si for low Si concentrations (below 5 wt.%) and close to the U-Mo for higher Si concentrations. For Si weight fraction in the Al alloy lower than 5 wt.%, the Si-rich sub-layer (close to Al-Si) consists of U(Al, Si) 3 + UMo 2 Al 20 , when the other sub-layer (close to U-Mo) is silicon free and made of UAl 3 and U 6 Mo 4 Al 43 . For Si weight concentrations above 5 wt.%, the Si-rich part becomes U 3 (Si, Al) 5 + U(Al, Si) 3 (close to U-Mo) and the other sub-layer (close to Al-Si) consists of U(Al, Si) 3 + UMo 2 Al 20 . On the basis of these results and of a literature survey, a scheme is proposed to explain the formation of different types of ILs between U-Mo and Al-Si alloys (i.e. different protective layers).

Photoelectrochemical Water Splitting Properties of Ti-Ni-Si-O Nanostructures on Ti-Ni-Si Alloy

Directory of Open Access Journals (Sweden)

Ting Li

2017-10-01

Full Text Available Ti-Ni-Si-O nanostructures were successfully prepared on Ti-1Ni-5Si alloy foils via electrochemical anodization in ethylene glycol/glycerol solutions containing a small amount of water. The Ti-Ni-Si-O nanostructures were characterized by field-emission scanning electron microscopy (FE-SEM, energy dispersive spectroscopy (EDS, X-ray diffraction (XRD, and diffuse reflectance absorption spectra. Furthermore, the photoelectrochemical water splitting properties of the Ti-Ni-Si-O nanostructure films were investigated. It was found that, after anodization, three different kinds of Ti-Ni-Si-O nanostructures formed in the α-Ti phase region, Ti2Ni phase region, and Ti5Si3 phase region of the alloy surface. Both the anatase and rutile phases of Ti-Ni-Si-O oxide appeared after annealing at 500 °C for 2 h. The photocurrent density obtained from the Ti-Ni-Si-O nanostructure photoanodes was 0.45 mA/cm2 at 0 V (vs. Ag/AgCl in 1 M KOH solution. The above findings make it feasible to further explore excellent photoelectrochemical properties of the nanostructure-modified surface of Ti-Ni-Si ternary alloys.

NiTiCu/AlN/NiTiCu shape memory thin film heterostructures for vibration damping in MEMS

Energy Technology Data Exchange (ETDEWEB)

Kaur, Navjot; Kaur, Davinder, E-mail: dkaurfph@iitr.ernet.in

2014-03-25

Highlights: • Fabrication of NiTiCu/AlN/NiTiCu heterostructure using dc/rf magnetron sputtering. • Exhibits highest hardness (38 GPa) and elastic modulus (187 GPa). • Enhanced dissipation of mechanical energy (E{sub d} = 5.7 N J). • High damping capacity (0.052) and figure of merit (∼0.62). • Can be applied for vibration damping in MEMS. -- Abstract: Shape memory alloy (NiTiCu) thin films coupled with piezoelectric AlN layer produce an intelligent material for vibration damping. In the present study pure NiTiCu, NiTiCu/AlN and NiTiCu/AlN/NiTiCu heterostructures have been deposited on Si substrate using magnetron sputtering technique. By the use of the interfaces and shape memory effect provided by NiTiCu layers, the damping capacity can be increased along with increase in stiffness and mechanical hardness. The heterostructures were characterized in terms of structural, electrical, morphological and mechanical properties by X-ray diffraction (XRD), four probe resistivity method, atomic force microscopy, field emission scanning electron microscopy, and nanoindentation. The NiTiCu/AlN/NiTiCu heterostructure exhibit enhanced mechanical and damping properties as compared to NiTiCu/AlN and pure NiTiCu. This enhancement in hardness and damping of the heterostructure could be attributed to the shape memory effect of NiTiCu, intrinsic piezoelectricity of AlN and increased number of interfaces in heterostructure that help in dissipation of mechanical vibrations. The findings of this work provide additional impetus for the application of these heterostructures in emerging fields of nanotechnology and microelectro mechanical (MEMS) devices.

NiTiCu/AlN/NiTiCu shape memory thin film heterostructures for vibration damping in MEMS

International Nuclear Information System (INIS)

Kaur, Navjot; Kaur, Davinder

2014-01-01

Highlights: • Fabrication of NiTiCu/AlN/NiTiCu heterostructure using dc/rf magnetron sputtering. • Exhibits highest hardness (38 GPa) and elastic modulus (187 GPa). • Enhanced dissipation of mechanical energy (E d = 5.7 N J). • High damping capacity (0.052) and figure of merit (∼0.62). • Can be applied for vibration damping in MEMS. -- Abstract: Shape memory alloy (NiTiCu) thin films coupled with piezoelectric AlN layer produce an intelligent material for vibration damping. In the present study pure NiTiCu, NiTiCu/AlN and NiTiCu/AlN/NiTiCu heterostructures have been deposited on Si substrate using magnetron sputtering technique. By the use of the interfaces and shape memory effect provided by NiTiCu layers, the damping capacity can be increased along with increase in stiffness and mechanical hardness. The heterostructures were characterized in terms of structural, electrical, morphological and mechanical properties by X-ray diffraction (XRD), four probe resistivity method, atomic force microscopy, field emission scanning electron microscopy, and nanoindentation. The NiTiCu/AlN/NiTiCu heterostructure exhibit enhanced mechanical and damping properties as compared to NiTiCu/AlN and pure NiTiCu. This enhancement in hardness and damping of the heterostructure could be attributed to the shape memory effect of NiTiCu, intrinsic piezoelectricity of AlN and increased number of interfaces in heterostructure that help in dissipation of mechanical vibrations. The findings of this work provide additional impetus for the application of these heterostructures in emerging fields of nanotechnology and microelectro mechanical (MEMS) devices

Semisolid casting with ultrasonically melt-treated billets of Al-7mass%Si alloys

Directory of Open Access Journals (Sweden)

Yoshiki Tsunekawa

2012-02-01

Full Text Available The demand for high performance cast aluminum alloy components is often disturbed by increasing impurity elements, such as iron accumulated from recycled scraps. It is strongly required that coarse plate-like iron compound of モ-Al5FeSi turns into harmless form without the need for applying refining additives or expensive virgin ingots. The microstructural modification of Al-7mass%Si alloy billets with different iron contents was examined by applying ultrasonic vibration during the solidification. Ultrasonically melt-treated billets were thixocast right after induction heating up to the semisolid temperature of 583 ìC, the microstructure and tensile properties were evaluated in the thixocast components. Globular primary メ-Al is required to fill up a thin cavity in thixocasting, so that the microstructural modification by ultrasonic melt-treatment was firstly confirmed in the billets. With ultrasonic melt-treatment in the temperature range of 630 ìC to 605 ìC, the primary メ-Al transforms itself from dendrite into fine globular in morphology. The coarse plate-like モ-Al5FeSi compound becomes markedly finer compared with those in non-treated billets. Semisolid soaking up to 583 ìC, does not appreciably affect the size of モ-Al5FeSi compounds; however, it affects the solid primary メ-Al morphology to be more globular, which is convenient for thixocasting. After thixocasting with preheated billets, eutectic silicon plates are extremely refined due to the rapid solidification arising from low casting temperature. The tensile strength of thixocast samples with different iron contents does not change much even at 2mass% of iron, when thixocast with ultrasonically melt-treated billets. However, thixocast Al-7mass%Si-2mass%Fe alloy with non-treated billets exhibits an inferior strength of 80 MPa, compared with 180 MPa with ultrasonically melt-treated billets. The elongation is also improved by about a factor of two in thixocastings with

Thermodynamics of oxygen solutions in Fe-40% Ni-15% Cr melts containing Mn, Si, Ti, Al

International Nuclear Information System (INIS)

Dashevskij, V.Ya.; Makarova, N.N.; Grigorovich, K.V.; Kashin, V.I.; Polikarpova, N.V.

2000-01-01

Thermodynamic analysis and experimental studied are performed for oxygen solutions in Fe-40% Ni-15% Cr melts where Mn, Si, Ti, Al are used as reducing agents. It is revealed that in the alloys studied the affinity of reducing agents to oxygen essentially lower than in liquid iron, nickel and Fe-40% Ni alloy. This is explained by the fact that the oxygen activity in melts noticeably decreases due to a high chromium content whereas the activity of reducing elements increases in a rather less degree. The agreement between analytical and experimental results confirms the validity of the calculation technique [ru

Photoelectrochemical Water Splitting Properties of Ti-Ni-Si-O Nanostructures on Ti-Ni-Si Alloy.

Science.gov (United States)

Li, Ting; Ding, Dongyan; Dong, Zhenbiao; Ning, Congqin

2017-10-31

Ti-Ni-Si-O nanostructures were successfully prepared on Ti-1Ni-5Si alloy foils via electrochemical anodization in ethylene glycol/glycerol solutions containing a small amount of water. The Ti-Ni-Si-O nanostructures were characterized by field-emission scanning electron microscopy (FE-SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and diffuse reflectance absorption spectra. Furthermore, the photoelectrochemical water splitting properties of the Ti-Ni-Si-O nanostructure films were investigated. It was found that, after anodization, three different kinds of Ti-Ni-Si-O nanostructures formed in the α-Ti phase region, Ti₂Ni phase region, and Ti₅Si₃ phase region of the alloy surface. Both the anatase and rutile phases of Ti-Ni-Si-O oxide appeared after annealing at 500 °C for 2 h. The photocurrent density obtained from the Ti-Ni-Si-O nanostructure photoanodes was 0.45 mA/cm² at 0 V (vs. Ag/AgCl) in 1 M KOH solution. The above findings make it feasible to further explore excellent photoelectrochemical properties of the nanostructure-modified surface of Ti-Ni-Si ternary alloys.

Hydroconversion of methyl laurate on bifunctional Ni2P/AlMCM-41 catalyst prepared via in situ phosphorization using triphenylphosphine

Science.gov (United States)

Zhao, Sha; Zhang, Zhena; Zhu, Kongying; Chen, Jixiang

2017-05-01

A series of Ni2P/AlMCM-41-x bifunctional catalysts with different Si/Al ratios (x) were synthesized by in situ phosphorization of Ni/AlMCM-41-x with triphenylphosphine (nominal Ni/P ratio of 0.75) at 300 °C on a fixed-bed reactor. For comparison, NiP/AlMCM-41-5-TPR was also prepared by the TPR method from the supported nickel phosphate with the Ni/P ratio of 1.0, during which metallic Ni rather than Ni2P formed. TEM images show that Ni and Ni2P particles uniformly distributed in Ni2P/AlMCM-41-x and NiP/AlMCM-41-5-TPR. The Ni2P/AlMCM-41-x acidity increased with decreasing the Si/Al ratio. In the hydroconversion of methyl laurate, the conversions were close to 100% on all catalysts at 360 °C, 3.0 MPa, methyl laurate WHSV of 2 h-1 and H2/methyl laurate ratio of 25. As to Ni2P/AlMCM-41-x, with decreasing the Si/Al ratio, the total selectivity to C11 and C12 hydrocarbons decreased, while the total selectivity to isoundecane and isododecane (Si-C11+i-C12) firstly increased and then decreased. Ni2P/AlMCM-41-5 gave the largest Si-C11+i-C12 of 43.2%. While NiP/AlMCM-41-5-TPR gave higher Si-C11+i-C12 than Ni2P/AlMCM-41-5, it was more active for the undesired Csbnd C bond cleavage and methanation. We propose that the in-situ phosphorization adopted here is a promising approach to preparing Ni2P-based bifunctional catalysts.

Corrosive sliding wear behavior of laser clad Mo2Ni3Si/NiSi intermetallic coating

International Nuclear Information System (INIS)

Lu, X.D.; Wang, H.M.

2005-01-01

Many ternary metal silicides such as W 2 Ni 3 Si, Ti 2 Ni 3 Si and Mo 2 Ni 3 Si with the topologically closed-packed (TCP) hP12 MgZn 2 type Laves phase crystal structure are expected to have outstanding wear and corrosion resistance due to their inherent high hardness and sluggish temperature dependence and strong atomic bonds. In this paper, Mo 2 Ni 3 Si/NiSi intermetallic coating was fabricated on substrate of an austenitic stainless steel AISI321 by laser cladding using Ni-Mo-Si elemental alloy powders. Microstructure of the coating was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy dispersive X-ray analysis (EDS). Wear resistance of the coating is evaluated under corrosive sliding wear test condition. Influence of corrosion solutions on the wear resistance of the coating was studied and the wear mechanism was discussed based on observations of worn surface morphology. Results showed that the laser clad Mo 2 Ni 3 Si/NiSi composite coating have a fine microstructure of Mo 2 Ni 3 Si primary dendrites and the interdendritic Mo 2 Ni 3 Si/NiSi eutectics. The coating has excellent corrosive wear resistance compared with austenitic stainless steel AISI321 under acid, alkaline and saline corrosive environments

Production of Al2O3–SiC nano-composites by spark plasma sintering; Producción de nano-composites – SiC–Al2O3 por spark plasma sinterizado

Energy Technology Data Exchange (ETDEWEB)

Mansour Razavi; Ali Reza Farajipour; Mohammad Zakeri; Mohammad Reza Rahimipour; Ali Reza Firouzbakht

2017-11-01

In this paper, Al2O3–SiC composites were produced by SPS at temperatures of 1600°C for 10min under vacuum atmosphere. For preparing samples, Al2O3 with the second phase including of micro and nano-sized SiC powder were milled for 5h. The milled powders were sintered in a SPS machine. After sintering process, phase studies, densification and mechanical properties of Al2O3–SiC composites were examined. Results showed that the specimens containing micro-sized SiC have an important effect on bulk density, hardness and strength. The highest relative density, hardness and strength were 99.7%, 324.6 HV and 2329MPa, respectively, in Al2O3–20wt% SiCmicro composite. Due to short time sintering, the growth was limited and grains still remained in nano-meter scale. [Spanish] En este trabajo se muestran compuestos de Al2O3-SiC producidos por SPS, en vacío, a 1.600 °C durante 10 min. Para la preparación de muestras, se molieron polvos de Al2O3 durante 5 h con la segunda fase de micro-y-nano polvo de SiC. Posteriormente, estos polvos molidos se sinterizaron mediante SPS. Después del proceso de sinterización, se realizaron estudios de fase, densificación y propiedades mecánicas de los compuestos de Al2O3-SiC obtenidos. Los resultados mostraron que micro-SiC en las muestras tiene un efecto importante en su densidad aparente, dureza y resistencia. La mayor densidad relativa, dureza y resistencia fueron respectivamente del 99,7%, 324,6 HV y 2.329 MPa para Al2O3 con un 20% en peso micro-SiC. Debido al corto tiempo de sinterización, el crecimiento los granos fue limitado y se mantuvieron en escala nanométrica.

A relevância do dividendo adicional proposto

Directory of Open Access Journals (Sweden)

Ricardo Luiz Menezes da Silva

2016-01-01

Full Text Available Sobre la base de la Teoría de Dividendos de señalización, que son vistos como indicadores de información sobre el mercado. Sin embargo, tras la adopción de IFRS muchas empresas hacer uso del Dividendo Adicional Propuesto (DAP, que, hasta la resolución de los accionistas, no se caracteriza por ser una obligación. En este contexto, el objetivo del estudio fue analizar la importancia de la difusión de la DAP para el mercado de capitales brasileño. A través de regresiones con datos de panel, entre 2010-2012, se encontró que el DAP influye en el precio de las acciones debido a su contenido informativo, revelando información útil para el mercado, de acuerdo con los estudios de área. Por lo tanto, como una contribución, el estudio muestra que la vista de los inversores, el aumento de la distribución de dividendos indica un signo positivo de mayores beneficios en el futuro, en consonancia con la Teoría de Dividendos de señalización, incluso si estos dividendos no tener la obligación fecha de presentación del balance general.

Phase Equilibria of the Sn-Ni-Si Ternary System and Interfacial Reactions in Sn-(Cu)/Ni-Si Couples

Science.gov (United States)

Fang, Gu; Chen, Chih-chi

2015-07-01

Interfacial reactions in Sn/Ni-4.5 wt.%Si and Sn-Cu/Ni-4.5 wt.%Si couples at 250°C, and Sn-Ni-Si ternary phase equilibria at 250°C were investigated in this study. Ni-Si alloys, which are nonmagnetic, can be regarded as a diffusion barrier layer material in flip chip packaging. Solder/Ni-4.5 wt.%Si interfacial reactions are crucial to the reliability of soldered joints. Phase equilibria information is essential for development of solder/Ni-Si materials. No ternary compound is present in the Sn-Ni-Si ternary system at 250°C. Extended solubility of Si in the phases Ni3Sn2 and Ni3Sn is 3.8 and 6.1 at.%, respectively. As more Si dissolves in these phases their lattice constants decrease. No noticeable ternary solubility is observed for the other intermetallics. Interfacial reactions in solder/Ni-4.5 wt.%Si are similar to those for solder/Ni. Si does not alter the reaction phases. No Si solubility in the reaction phases was detected, although rates of growth of the reaction phases were reduced. Because the alloy Ni-4.5 wt.%Si reacts more slowly with solders than pure Ni, the Ni-4.5 wt.%Si alloy could be a potential new diffusion barrier layer material for flip chip packaging.

Tratamiento con inmunoterapia específica en niños con Rinitis Alérgica y/o Asma Bronquial. Área Norte. 2005 - 2007.

Directory of Open Access Journals (Sweden)

Matilde Iraida Morera Franco

2007-10-01

Full Text Available Se realizó un estudio descriptivo longitudinal durante el período Enero 2005_ Enero 2007 en el Policlínico Norte del municipio Sancti Spíritus. El universo estuvo constituido por el total de niños con edades de 2_15 años con enfermedades alérgicas, a los que se realizó pruebas de alergia e indicó tratamiento con inmunoterapia específica por vía subcutánea, la muestra estuvo formada por 75 pacientes con asma bronquial, rinitis alérgica y/o ambas enfermedades, con el objetivo de determinar el comportamiento del tratamiento con inmunoterapia específica se aplicó el método porcentual para el análisis de resultados, donde el grupo etáreo que predominó fue de 2 _5 años, más del 65 % de los pacientes tratados refirieron mejoría de los síntomas las causas más frecuentes de abandono de tratamiento fue la aparición de infecciones intercurrentes, no ocurrió reacción anafiláctica en ninguno de los casos estudiados, el tratamiento con inmunoterapia puede reducir el uso de otros tratamientos asociados como Intal, antihistamínicos, broncodilatadores y esteroides.

con bajo peso al nacer

Directory of Open Access Journals (Sweden)

Adriana Mora Antó

2005-01-01

Full Text Available Esta investigación dio cuenta de la relación entre el estilo de funcionamiento familiar, los patrones de crianza y las edades de desarrollo evolutivo en niños, nacidos con bajo peso. El estudio descriptivo correlacional se realizó con 41 niños y sus madres, aplicándose cuestionarios sobre funcionamiento familiar, prácticas de crianza y desarrollo infantil. Los resultados señalaron la existencia de un funcionamiento familiar caracterizado por una cohesión amalgamada y una adaptabilidad caótica, una disciplina complaciente, falta de control y de límites claros en la díada madre-hijo. Se trataba de familias monoparentales, donde la temprana edad de concepción, el madresolterismo y el apoyo de la familia extensa eran constantes. Las edades evolutivas registradas indicaron un desarrollo inferior a la edad cronológica, en la mayor parte de los casos; sin embargo, éstas tendieron a ser superiores al compararlas con la edades reales de los infantes. No se encontró una correlación estadísticamente significativa entre la edad de desarrollo y los diferentes factores del funcionamiento familiar para algunos de los rangos de edad considerados; sin embargo, no se lo descartó por completo, especialmente en lo referente al optimismo familiar

Characterization and electrochemical properties of Ni(Si)/Ni5Si2 multiphase coatings prepared by HVOF spraying

Science.gov (United States)

Verdian, M. M.; Raeissi, K.; Salehi, M.

2012-11-01

Ni(Si)/Ni5Si2 powders were produced by mechanical alloying (MA) of Ni-25 at.% Si powder mixture. Then, the as-milled powders were sprayed onto copper substrate using high velocity oxy-fuel (HVOF) process. The phase composition and microstructure of the coatings were examined by X-ray diffractometry and scanning electron microscopy. Polarization tests and electrochemical impedance spectroscopy (EIS) measurements were also employed to study corrosion performance of the coatings in 3.5% NaCl solution. The results showed that although single phase Ni3Si was formed during annealing of Ni(Si)/Ni5Si2 powders, but, only Ni(Si) and Ni5Si2 are present in HVOF coatings and no new phase has been formed during spraying. The coatings had microhardness up to 746 HV0.05. Further investigations showed the corrosion performance of multiphase coatings in 3.5% NaCl solution was better than that of copper substrate. The phase transitions during MA, HVOF and annealing processes were discussed in association with Ni-Si phase diagram and nature of each process.

Strength and ductility of Ni3Al alloyed with boron and substitutional elements

International Nuclear Information System (INIS)

Ishikawa, K.; Aoki, K.; Masumoto, T.

1995-01-01

The effect of simultaneous alloying of boron (B) and the substitutional elements M on mechanical properties of Ni 3 Al was investigated by the tensile test at room temperature. The yield strength of Ni 3 Al+B increases by alloying with M except for Fe and Ga. In particular, it increases by alloying with Hf, Nb, W, Ta, Pd and Si. The fracture strength of Ni 3 Al+B increases by alloying with Pd, Ga, Si and Hf, but decreases with the other elements. Elongation of Ni 3 Al+B increases by alloying with Ga, Fe and Pd, but decreases with other elements. Hf and Pd is the effective element for the increase of the yield strength and the fracture strength of Ni 3 Al+B, respectively. Alloying with Hf leads to the increases of the yield strength and the fracture strength of Ni 3 Al+B, but to the lowering of elongation. On the other hand, alloying with Pd improves all mechanical properties, i.e. the yield strength, the fracture strength and elongation. On the contrary, alloying with Ti, V and Co leads to the lowering of mechanical properties of Ni 3 Al+B. The reason why ductility of Ni 3 Al+B is reduced by alloying with some elements M is discussed

Magnetic order of Y{sub 3}NiSi{sub 3}-type R{sub 3}NiSi{sub 3} (R=Gd–DY) compounds

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, GSP-2, Moscow 119992 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Faculty of Geology, Moscow State University, Leninskie Gory, Moscow 119992 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Malik, S.K.; Quezado, S. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59082-970 (Brazil); Yao, Jinlei; Mozharivskyj, Y. [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4M1 (Canada); Nigam, A.K. [Tata Institute of Fundamental Research, Mumbai 400005 (India); Isnard, O. [Université Grenoble Alpes, Inst NEEL, BP166, F-38042 Grenoble (France); CNRS, Institut NEEL, 25 rue des martyrs, F-38042 Grenoble (France)

2016-01-15

Magnetic measurements and neutron powder diffraction investigations on the Y{sub 3}NiSi{sub 3}-type R{sub 3}NiSi{sub 3} compounds (R=Gd, Tb, Dy) reveal their complex antiferromagnetic ordering. Magnetic measurements on Gd{sub 3}NiSi{sub 3}, Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} indicate antiferromagnetic-like transition at temperatures 260 K, 202 K and 140 K, respectively. Also, the Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} compounds show spin-reorientation transition at 132 K and 99 K, respectively. Below the spin-reorientation transition, the isothermal magnetization curves indicate the metamagnetic-like behavior of Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3}. The magnetocaloric effect of Dy{sub 3}NiSi{sub 3} is calculated in terms of isothermal magnetic entropy change and it reaches a maximum value of −1.2 J/kg K and −1.1 J/kg K for a field change of 50 kOe near 146 K and 92 K, respectively. The neutron diffraction studies of Tb{sub 3}NiSi{sub 3} suggest the magnetic ordering of the Tb2 4j sublattice and no magnetic ordering of the Tb1 2a sublattice. Tb{sub 3}NiSi{sub 3} transforms from the high temperature paramagnetic state to the commensurate high-temperature a- and c-axis antiferromagnet of I′2/m magnetic space group below 250 K. Below 150 K, the high-temperature antiferromagnet transforms into the low-temperature a-, b- and c-axis antiferromagnet of I′i magnetic space group. At 1.5 K, the terbium magnetic moment in Tb2 sublattice and its a-, b- and c-axis components reach the values of M{sub Tb2}=8.2(1) μ{sub B}, M{sub aTb2}=5.9(1) μ{sub B}, M{sub bTb2}=4.3(2) μ{sub B} and M{sub cTb2}=3.7(2) μ{sub B}, respectively. - Highlights: • Gd{sub 3}NiSi{sub 3}, Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} have Neel points of 260. 202 and 140 K. • Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} show spin-reorientation transition at 132 and 99 K. • Tb{sub 3}NiSi{sub 3} exhibits the commensurate magnetic ordering of Tb2 4j sublattice

Ion beam mixing of marker layers in Al and Si

International Nuclear Information System (INIS)

Mantl, S.; Rehn, L.E.; Averback, R.S.; Thompson, L.J. Jr.

1984-07-01

Ion beam mixing experiments on thin Pt, Au, and Ni markers in Al and Si have performed at 17, 85, and 300 K. After irradiation with 300-keV Ar ions the broadening and relative shifts of the markers have been determined by RBS measurements. The marker broadenings are more pronounced in Si than in Al; in both matrices the broadenings decrease in the following order: Au, Pt, and Ni. No dependence of mixing on irradiation temperature was observed between 17 and 300 K. The shifts of the heavy Au and Pt markers relative to the Ni markers are approximately equal to the experimental accuracy. However, a shift of the Ni marker toward the surface relative to the heavier Au and Pt markers was consistently observed. 13 references, 2 figures

Chemical diffusion of Cr, Ni and Si in welded joints. II

International Nuclear Information System (INIS)

Kucera, J.; Ciha, K.

1987-01-01

The results are given of a study in chemical diffusion in welded joints P2/A and P3/A. P2 stands for the steel (Fe-17.48 Cr-8.15 Ni-0.14 Si), P3 for (Fe-18.52 Cr-8.20 Ni-1.78 Si) and A for the Fe-Arema. Triadic sandwiche-like samples were diffusion heated at temperatures from 920 to 1170 degC. The concentration distributions N(x,t) of the given elements were measured with microprobe JXA-3A. The evaluation of the experimental data was carried out either by Grube's method, or in some cases by the spline-polynomial method. The evaluated diffusivities D-bar satisfy the Arrhenius relation and yield the standard diffusion characteristics D 0 and H. The diffusivities D-bar of Cr, Ni and Si in P1/A, in P2/A and P3/A welded joints vary with Si content in P1, P2 and P3 alloys, similar to the Cr-51 and Ni-63 self-diffusivities in Fe-18 Cr-12 Ni-X Si steels, and tend to increase with increasing Si content. The values D-bar measured in the vicinity of grain boundaries are higher than the bulk diffusion coefficients. The most rapid diffusant is Si and the slowest one Ni. Thus, the relations D-bar Si :D-bar Cr :D-bar Ni ≅ 6:3:1 (P3/A) and D-bar Si :D-bar Cr :D-bar Ni ≅ 1.7:1.4:1 (P3/A) are valid at 1050 degC. Comparing the results with those published if can be noted that the Cr-51 and Ni-63 self-diffusion in Fe-18 Cr-12 Ni-X Si steels is faster than chemical diffusion of these elements in the said steel welded joints P2/A and P3/A; X varies from 0.14 to 1.98. (author). 7 tabs., 7 figs., 20 refs

Formation of abrasion-resistant coatings of the AlSiFexMny intermetallic compound type on the AISI 304L alloy

Directory of Open Access Journals (Sweden)

Martínez-Perales, Laura G.

2016-03-01

adherida, con microdureza de 1300 Vickers. Los resultados de MEB y DRX confirman la formación de intermetálicos α-Al9FeMnSi y β-Al9FeMn2Si en la interfase sustrato/ recubrimiento, así como la presencia de Cr y Ni, indicando la difusión de estos dos elementos del sustrato a la interfaz.

Estilo de funcionamiento familiar, pautas de crianza y su relación con el desarrollo evolutivo en niños con bajo peso al nacer

Directory of Open Access Journals (Sweden)

Adriana Mora Antó

2005-05-01

Full Text Available Esta investigación dio cuenta de la relación entre el estilo de funcionamiento familiar, los patrones de crianza y las edades de desarrollo evolutivo en niños, nacidos con bajo peso. El estudio descriptivo correlacional se realizó con 41 niños y sus madres, aplicándose cuestionarios sobre funcionamiento familiar, prácticas de crianza y desarrollo infantil. Los resultados señalaron la existencia de un funcionamiento familiar caracterizado por una cohesión amalgamada y una adaptabilidad caótica, una disciplina complaciente, falta de control y de límites claros en la díada madre-hijo. Se trataba de familias monoparentales, donde la temprana edad de concepción, elMadre solterismo y el apoyo de la familia extensa eran constantes. Las edades evolutivas registradas indicaron un desarrollo inferior a la edad cronológica, en la mayor parte de los casos; sin embargo, éstas tendieron a ser superiores al compararlas con las edades reales de los infantes. No se encontró una correlación estadísticamente significativa entre la edad de desarrollo y los diferentes factores del funcionamiento familiar para algunos de los rangos de edad considerados; sin embargo, no se lo descartó por completo, especialmente en lo referente al optimismo familiar.

Preparación Física con niños y jóvenes. Una perspectiva metodológica

OpenAIRE

Los Santos i Poquet, Carles

2000-01-01

La gran mayoría de los profesionales y no profesionales del entrenamiento deportivo nos movemos o trabajamos sobre todo con niños y niñas de diversas edades y no tanto con categorías de adultos. La infancia y la adolescencia son unas etapas muy delicadas en la vida de la persona y esto me hace pensar si trabajamos con ellos correctamente desde un punto de vista pedagógico, aplicando una metodología adecuada para ellos y si buscamos lo que les corresponde para su edad, a nivel físico y deporti...

Transmission electron microscopy characterization of irradiated U-7Mo/Al-2Si dispersion fuel

International Nuclear Information System (INIS)

Gan, J.; Keiser, D.D.; Wachs, D.M.; Robinson, A.B.; Miller, B.D.; Allen, T.R.

2010-01-01

The plate-type dispersion fuels, with the atomized U(Mo) fuel particles dispersed in the Al or Al alloy matrix, are being developed for use in research and test reactors worldwide. It is found that the irradiation performance of a plate-type dispersion fuel depends on the radiation stability of the various phases in a fuel plate. Transmission electron microscopy was performed on a sample (peak fuel mid-plane temperature ∼109 deg. C and fission density ∼4.5 x 10 27 f m -3 ) taken from an irradiated U-7Mo dispersion fuel plate with Al-2Si alloy matrix to investigate the role of Si addition in the matrix on the radiation stability of the phase(s) in the U-7Mo fuel/matrix interaction layer. A similar interaction layer that forms in irradiated U-7Mo dispersion fuels with pure Al matrix has been found to exhibit poor irradiation stability, likely as a result of poor fission gas retention. The interaction layer for both U-7Mo/Al-2Si and U-7Mo/Al fuels is observed to be amorphous. However, unlike the latter, the amorphous layer for the former was found to effectively retain fission gases in areas with high Si concentration. When the Si concentration becomes relatively low, the fission gas bubbles agglomerate into fewer large pores. Within the U-7Mo fuel particles, a bubble superlattice ordered as fcc structure and oriented parallel to the bcc metal lattice was observed where the average bubble size and the superlattice constant are 3.5 nm and 11.5 nm, respectively. The estimated fission gas inventory in the bubble superlattice correlates well with the fission density in the fuel.

Two directional microstructure and effects of nanoscale dispersed Si particles on microhardness and tensile properties of AlSi7Mg melt-spun alloy

Energy Technology Data Exchange (ETDEWEB)

Dong, Xixi, E-mail: dongxx09@mails.tsinghua.edu.cn [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); He, Liangju [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); School of Aerospace, Tsinghua University, Beijing 100084 (China); Mi, Guangbao [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Li, Peijie [National Center of Novel Materials for International Research, Tsinghua University, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China)

2015-01-05

Highlights: • Both surface and cross-sectional microstructure of AlSi7Mg ribbon were characterized. • 13–50 nm and 50-hundreds of nm Si particles were dispersed both in α-Al and its boundary. • Tensile property of AlSi7Mg ribbon was studied with UTS 1.5 times higher than ingot. • Effects of nanoscale Si particles on hardness and tensile properties were provided. - Abstract: The two directional microstructure and multiple mechanical properties of the AlSi7Mg ribbon produced by melt-spun were investigated by optical microscopy (OM), field emission gun scanning electron microscope (FEGSEM), X-ray diffraction (XRD), microhardness and tensile tests. Both the surface and cross-sectional microstructure of the melt-spun ribbon were characterized in detail to give a clear and integrated description of the microstructure. Two kinds of nanoscale Si particles were observed, i.e., small Si particles ranging from 13 to 50 nm and large Si particles ranging from 50 nm to several hundreds of nanometers with clear size boundary were dispersed both in the interior and boundary of fine α-Al. XRD results revealed supersaturated solution of Si in Al matrix to be 0.62 at.%. The ultimate tensile strength, yield strength, and hardness of the ribbon were 1.53, 1.75 and 1.56 times higher than that of the conventional cast ingot separately. The breaking elongation of the ribbon was 1.73% with intergranular fracture feature. The effects of nanoscale dispersed Si particles on the significant improvement of both hardness and tensile properties of the AlSi7Mg melt-spun ribbon were discussed in detail.

Microstructural evolution of direct chill cast Al-15.5Si-4Cu-1Mg-1Ni-0.5Cr alloy during solution treatment

OpenAIRE

He Kezhun; Yu Fuxiao; Zhao Dazhi

2011-01-01

Heat treatment has important influence on the microstructure and mechanical properties of Al-Si alloys. The most common used heat treatment method for these alloys is solution treatment followed by age-hardening. This paper investigates the microstructural evolution of a direct chill (DC) cast Al-15.5Si-4Cu-1Mg-1Ni-0.5Cr alloy after solution treated at 500, 510, 520 and 530℃, respectively for different times. The major phases observed in the as-cast alloy are α-aluminum dendrite, primary Si p...

Bulk-compositional changes of Ni2Al3 and NiAl3 during ion etching

International Nuclear Information System (INIS)

Chen Houwen; Wang Rong

2008-01-01

Bulk-compositional changes of Ni 2 Al 3 and NiAl 3 in a Ni-50 wt% Al alloy during ion etching have been investigated by transmission electron microscopy and energy dispersive X-ray spectroscopic analyses. After etching with 7, 5 and 3 keV Ar + ions for 15, 24 and 100 h nickel contents in both Ni 2 Al 3 and NiAl 3 exceeded greatly those in the initial compounds and increased with the decrement of the sputtering energy. After 100 h etching with 3 keV Ar + ions the compositions of these two compounds reached a similar value, about Ni 80-83 Al 12-15 Fe 3-4 Cr 1-2 (at%). A synergistic action of preferential sputtering, radiation-induced segregation and radiation-enhanced diffusion enables the altered-layers at the top and bottom of the film extend through the whole film. The bulk-compositional changes are proposed to occur in the unsteady-state sputtering regime of ion etching and caused by an insufficient supply of matter in a thin film

Microporous Ni@NiO nanoparticles prepared by chemically dealloying Al_3Ni_2@Al nanoparticles as a high microwave absorption material

International Nuclear Information System (INIS)

Pang, Yu; Xie, Xiubo; Li, Da; Chou, Wusheng; Liu, Tong

2017-01-01

The Al_3Ni_2@Al nanoparticles (NPs) were prepared from Ni_4_5Al_5_5 master alloy by hydrogen plasma-metal reaction method, and were subsequently dealloyed to produce porous Ni@NiO NPs of 36 nm. The pore size ranges from 0.7 to 1.6 nm, leading to large specific surface area of 69.5 m"2/g and big pore volume of 0.507 cc/g. The saturation magnetization (M_S) and coercivity (H_C) of the microporous Ni@NiO NPs are 11.5 emu/g and 5.2 Oe. They exhibit high microwave absorption performance with a minimum reflection coefficient (RC) of −86.9 dB and an absorption bandwidth of 2.6 GHz (RC≤−10 dB) at thickness of 4.5 mm. The enhanced microwave absorption properties are attributed to the synergistic effect of the magnetic Ni core and dielectric NiO shell, and the micropore architecture. The NPs with micropore morphology and core/shell structure open a new way to modify the microwave absorption performance. - Graphical abstract: The microporous Ni/NiO nanoparticles prepared by chemically dealloying Al_3Ni_2@Al NPs exhibit high microwave absorption intensity (−86.9 dB) and wide absorption bandwidth (2.6 GHz for RC≤−10 dB). - Highlights: • Microporous Ni/NiO nanoparticals were prepared by chemically dealloying method. • They possessed micropores of 0.7–1.6 nm with a surface area of 69.5 m"2/g. • They showed high microwave absorption intensity and wide absorption bandwidth. • Microwave absorption mechanism was explained by micropore and core/shell structures.

Comorbilidad de los trastornos de lectura y escritura en niños diagnosticados con TDAH

Directory of Open Access Journals (Sweden)

César Mejía Z

2015-01-01

Full Text Available El objetivo de este estudio fue describir la presencia de Trastornos Específicos del Aprendizaje (TEA en lectura y escritura en un grupo de niños y niñas de la ciudad de Manizales, diagnosticados con Trastorno por Déficit de Atención e Hiperactividad. La aproximación considera las variables de precisión, comprensión, composición y velocidad, para lo cual se usó la Evaluación Neuropsicológica Infantil (ENI. Estas áreas fueron evaluadas en una muestra de 60 niños y niñas con TDAH entre 7 y 11 años, de tercero a quinto grado de primaria. Al comparar el desempeño de los grupos de casos y controles, se encontraron diferencias estadísticamente significativas en el área de la lectura. En el área de escritura, solo se encuentran diferencias estadísticamente significativas en tareas de composición narrativa. No obstante, en las áreas de escritura donde no se encuentran diferencias entre los grupos se observa una alta frecuencia de sujetos del grupo control con puntuaciones correspondientes al criterio diagnóstico de TEA. En conclusión, se observa una alta asociación entre el TDAH y los TEA.

Chemical vapor deposition of NiSi using Ni(PF3)4 and Si3H8

International Nuclear Information System (INIS)

Ishikawa, M.; Muramoto, I.; Machida, H.; Imai, S.; Ogura, A.; Ohshita, Y.

2007-01-01

NiSi x films were deposited using chemical vapor deposition (CVD) with a Ni(PF 3 ) 4 and Si 3 H 8 /H 2 gas system. The step coverage quality of deposited NiSi x was investigated using a horizontal type of hot-wall low pressure CVD reactor, which maintained a constant temperature throughout the deposition area. The step coverage quality improved as a function of the position of the gas flow direction, where PF 3 gas from decomposition of Ni(PF 3 ) 4 increased. By injecting PF 3 gas into the Ni(PF 3 ) 4 and Si 3 H 8 /H 2 gas system, the step coverage quality markedly improved. This improvement in step coverage quality naturally occurred when PF 3 gas was present, indicating a strong relationship. The Si/Ni deposit ratio at 250 deg. C is larger than at 180 deg. C. It caused a decreasing relative deposition rate of Ni to Si. PF 3 molecules appear to be adsorbed on the surface of the deposited film and interfere with faster deposition of active Ni deposition species

Resultados de una intervención motivacional con niños obesos o con sobrepeso y sus familias: Estudio Piloto

Directory of Open Access Journals (Sweden)

Pedro Juan Tárraga López

2017-12-01

Full Text Available Introducción: el objetivo fue analizar los resultados de una intervención motivacional con modificación de los hábitos alimentarios, los estilos de vida y los trastornos emocionales en niños obesos de 6 a 12 años y sus familias. Material y métodos: Estudio de intervención con evaluación pre- y posintervención del programa Familias en Movimiento. Se incluyeron 11 niños (10 niñas y 1 niño de 6 a 12 años tratados con otros programas para la pérdida de peso sin éxito. Se evaluaron al inicio y al final los parámetros: Índice de Masa Corporal (IMC, los resultados de los cuestionarios: de Dieta Mediterránea y ansiedad en niños y el peso y la ansiedad de los adultos tras la intervención. Resultados: El IMC disminuyó de una mediana de 25,2 (Rango intercuartílico de 23,3–28,0 a 23,9 y (22,9–27,6 tras la intervención, cambio no estadísticamente significativo (p<0,086. La mediana de adherencia a la Dieta Mediterránea aumentó significativamente en 2,2 puntos (7,1 a 9,3, debido principalmente a que un mayor número de niños tomaban desayuno (44% y hubo una disminución del consumo de golosinas y bollería industrial en el desayuno (22,2%. La intervención redujo significativamente en 8,7 puntos la ansiedad en los niños. De los adultos, 9 de ellos participaron en la evaluación inicial, la media de disminución de peso fue de 3,6kg y la disminución de la ansiedad pasó de 45,6 a 27,3 (p=0,02. Conclusiones: La aplicación del programa Familias en Movimiento disminuyó el IMC, aumentó la puntuación en la adherencia a Dieta Mediterránea y disminuyó la ansiedad en los niños, además se redujo el peso y la ansiedad en los adultos que acompañaron en el programa a los niños.

Investigations on sysnthesis, characterization and hydrogenation behaviour of the spin- and thermal-melted versions of LaNi{sub 5-x}Si{sub x}(x=0.1, 0.3, 0.5) hydrogen storage materials

Energy Technology Data Exchange (ETDEWEB)

Srivastava, S.; Srivastava, O.N. [Banaras Hindu Univ., Varanasi (India). Dept. of Physics

1998-03-06

The present study deals with investigations on the synthesis and characterisation of negative electrode material for high energy density Ni-MH battery. The hydrogen storage material (MH) has been synthesised trough normal casting and melt-spinning techniques. In LaNi{sub 5}/MmNi{sub 5} family various substitutions like Al, Mn, Co have been studied. The substitution of metalloid like Si is known to be very helpful in improving several hydrogenation properties. In the present study, the Si substituted versions of AB{sub 5}-type storage materials typified by LaNi{sub 5-x}Si{sub x} (x=0.1, 0.3, 0.5) habe been investigated. A comparison between the present material and the conventional AB{sub 5}-type material MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4} has been made which has been previously studied. The main features revealed by XRD characterisations are the existence of the free Ni and Si together with AB{sub 5} material for all the three compositions. These free Ni and Si were found to disappear and yield, giving rise to a singular material after hydrogenation. The melt-spun version of the material was found to grow invariably in a direction perpendicular to the c-axis. The kinetics and activation process was better for the melt-spun version of the LaNi{sub 4.7}Si{sub 0.3} alloy than its thermally-melted counterpart (bulk) as well as to the alloy MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4}. For example, the kinetics of the melt-spun version of LaNi{sub 4.7}Si{sub 0.3} is 60% faster than its bulk version and 70% faster than the melt-spun version of MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4}. Similarly, the melt-spund version of the alloy LaNi{sub 4.7}Si{sub 0.3} gets activated in the 2nd cycle itself where as the alloy MmNi{sub 4.3}Al{sub 0.3}Mn{sub 0.4} attains this stage only in the 6th cycle. (orig.) 13 refs.

Interfacial microstructure of NiSi x/HfO2/SiO x/Si gate stacks

International Nuclear Information System (INIS)

Gribelyuk, M.A.; Cabral, C.; Gusev, E.P.; Narayanan, V.

2007-01-01

Integration of NiSi x based fully silicided metal gates with HfO 2 high-k gate dielectrics offers promise for further scaling of complementary metal-oxide- semiconductor devices. A combination of high resolution transmission electron microscopy and small probe electron energy loss spectroscopy (EELS) and energy dispersive X-ray analysis has been applied to study interfacial reactions in the undoped gate stack. NiSi was found to be polycrystalline with the grain size decreasing from top to bottom of NiSi x film. Ni content varies near the NiSi/HfO x interface whereby both Ni-rich and monosilicide phases were observed. Spatially non-uniform distribution of oxygen along NiSi x /HfO 2 interface was observed by dark field Scanning Transmission Electron Microscopy and EELS. Interfacial roughness of NiSi x /HfO x was found higher than that of poly-Si/HfO 2 , likely due to compositional non-uniformity of NiSi x . No intermixing between Hf, Ni and Si beyond interfacial roughness was observed

Effect of Fe, Ni, and Cr on the corrosion behaviour of hyper-eutectic Al-Si automotive alloy under different pH conditions

Directory of Open Access Journals (Sweden)

Mohammad Salim Kaiser

2018-05-01

Full Text Available Effect of Fe, Ni and Cr on the corrosion behaviour of hyper-eutectic Al-Si automotive alloy was studied. The test of corrosion behaviour at different environmental pH 1, 3, 5, 7, 9, 11 and 13 was performed using conventional gravimetric measurements and complemented by resistivity, optical micrograph, scanning electron microscopy (SEM and X-ray analyser (EDX investigations. The highest corrosion rate was observed at pH 13 followed by pH 1, while in the pH range of 3.0 to 11, there is a high protection of surface due to formation of stable surface oxide film. The highest corrosion rate at pH 13 is due to presence of sodium hydroxide in the solution in which the surface oxide film is soluble. At pH 1, however, high corrosion rate can be attributed to dissolution of Al due to the surface attack by aggressive chloride ions. Presence of Fe, Ni and Cr in hyper-eutectic Al-Si automotive alloy has significant effect on the corrosion rate at both environmental pH values. Resistivity of alloy surfaces initially decreases at pH 1 and pH 13 due to formation of thin films. The SEM images of corroded samples immersed in pH 1 solution clearly show pores due to uniform degradation of the alloy. In pH 13 solution, however, the corrosion layer looks more packed and impermeable.

Nonvolatile memory characteristics influenced by the different crystallization of Ni-Si and Ni-N nanocrystals

International Nuclear Information System (INIS)

Chen, W.-R.; Yeh, J.-L.; Chang, C.-Y.; Chang, T.-C.; Chen, S.-C.

2008-01-01

The formation of Ni-Si and Ni-N nanocrystals by sputtering a Ni 0.3 Si 0.7 target in argon and nitrogen environment were proposed in this paper. A transmission electron microscope analysis shows the nanocrystals embedded in the nitride layer. X-ray photoelectron spectroscopy and x-ray diffraction also offer the chemical material analysis of nanocrystals with surrounding dielectric and the crystallization of nanocrystals for different thermal annealing treatments. Nonvolatile Ni-Si nanocrystal memories reveal superior electrical characteristics for charge storage capacity and reliability due to the improvement of thermal annealing treatment. In addition, we used energy band diagrams to explain the significance of surrounding dielectric for reliability

Hydroconversion of methyl laurate on bifunctional Ni{sub 2}P/AlMCM-41 catalyst prepared via in situ phosphorization using triphenylphosphine

Energy Technology Data Exchange (ETDEWEB)

Zhao, Sha; Zhang, Zhena [Tianjin Key Laboratory of Applied Catalysis Science and Technology, Department of Catalysis Science and Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Zhu, Kongying, E-mail: ausky@tju.edu.cn [Analysis and Measurement Center, Tianjin University, Tianjin 300072 (China); Chen, Jixiang, E-mail: jxchen@tju.edu.cn [Tianjin Key Laboratory of Applied Catalysis Science and Technology, Department of Catalysis Science and Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

2017-05-15

Highlights: • Bifunctional Ni{sub 2}P/AlMCM-41 was prepared by in situ phosphorization at 300 °C. • There were similar Ni{sub 2}P particle sizes in Ni{sub 2}P/AlMCM-41 with different Si/Al ratios. • The acid amount of Ni{sub 2}P/AlMCM-41 increased with decreasing the Si/Al ratio. • Ni{sub 2}P/AlMCM-41 with the Si/Al ratio of 5 had the highest activity for isomerization. • Ni{sub 2}P/AlMCM-41 had very low activity for methanation and C−C bond hydrogenolysis. - Abstract: A series of Ni{sub 2}P/AlMCM-41-x bifunctional catalysts with different Si/Al ratios (x) were synthesized by in situ phosphorization of Ni/AlMCM-41-x with triphenylphosphine (nominal Ni/P ratio of 0.75) at 300 °C on a fixed-bed reactor. For comparison, NiP/AlMCM-41-5-TPR was also prepared by the TPR method from the supported nickel phosphate with the Ni/P ratio of 1.0, during which metallic Ni rather than Ni{sub 2}P formed. TEM images show that Ni and Ni{sub 2}P particles uniformly distributed in Ni{sub 2}P/AlMCM-41-x and NiP/AlMCM-41-5-TPR. The Ni{sub 2}P/AlMCM-41-x acidity increased with decreasing the Si/Al ratio. In the hydroconversion of methyl laurate, the conversions were close to 100% on all catalysts at 360 °C, 3.0 MPa, methyl laurate WHSV of 2 h{sup −1} and H{sub 2}/methyl laurate ratio of 25. As to Ni{sub 2}P/AlMCM-41-x, with decreasing the Si/Al ratio, the total selectivity to C11 and C12 hydrocarbons decreased, while the total selectivity to isoundecane and isododecane (S{sub i-C11+i-C12}) firstly increased and then decreased. Ni{sub 2}P/AlMCM-41-5 gave the largest S{sub i-C11+i-C12} of 43.2%. While NiP/AlMCM-41-5-TPR gave higher S{sub i-C11+i-C12} than Ni{sub 2}P/AlMCM-41-5, it was more active for the undesired C−C bond cleavage and methanation. We propose that the in-situ phosphorization adopted here is a promising approach to preparing Ni{sub 2}P-based bifunctional catalysts.

Relevancia valorativa del resultado global y sus componentes frente al resultado neto

Directory of Open Access Journals (Sweden)

Núria Arimany Serrat

2011-12-01

Full Text Available Este trabajo tiene como objeto verificar si el resultado global presenta mayor relevancia valorativa respecto al resultado tradicional, y si es así cuáles son los componentes del resultado global que explican las diferencias. El estudio muestra que el resultado global es una variable relevante tanto para explicar el valor intrínseco de la empresa como para explicar su rentabilidad. Sin embargo, sólo al explicar la rentabilidad el resultado global y su incremento aumentan la relevancia valorativa del resultado neto y su incremento. De los componentes analizados del resultado global, tan sólo los resultados por diferencias de conversión de la moneda extranjera a la moneda de presentación añaden poder explicativo adicional al del resultado neto, aunque sólo en los modelos de rentabilidad. Ni los resultados por valoración de instrumentos financieros a valor razonable con cambios en patrimonio ni los resultados por coberturas de flujos de efectivo aportan un mayor poder explicativo al del resultado neto.This study analyses if comprehensive income is more value relevant than the net income and, if that is the case, what are the elements of the comprehensive income explaining the difference. Our study shows that comprehensive income is a relevant variable both to explain the value of the company and also to explain its return. However, comprehensive income and its variation show to be more relevant than the net income and its variation only when explaining return. As for the components of the comprehensive income, foreign currency adjustments increase usefulness in the return models but cash flow hedges and adjustments due to fair value valuation do not add value relevance to the net income.

Uptake properties of Ni2+ by nCaO.Al2O3.2SiO2 (n=1-4) prepared from solid-state reaction of kaolinite and calcite.

Science.gov (United States)

Jha, Vinay Kumar; Kameshima, Yoshikazu; Nakajima, Akira; Okada, Kiyoshi; MacKenzie, Kenneth J D

2005-08-31

A series of nCaO.Al2O3.2SiO2 samples (n=1-4) were prepared by solid-state reaction of mechanochemically treated mixtures of kaolinite and calcite fired at 600-1000 degrees C for 24 h. All the samples were X-ray amorphous after firing at 600-800 degrees C but had crystallized by 900 degrees C. The main crystalline phases were anorthite (n=1), gehlenite (n=2 and 3) and larnite (n=4). The uptake of Ni2+ by nCaO.Al2O3.2SiO2 samples fired at 800 and 900 degrees C was investigated at room temperature using solutions with initial Ni2+ concentrations of 0.1-50 mmol/l. Amorphous samples (fired at 800 degrees C) showed a higher Ni2+ uptake capacity than crystalline samples (fired at 900 degrees C). Ni2+ uptake was found to increase with increasing of CaO content. Amorphous 4CaO.Al2O3.2SiO2 showed the highest Ni2+ uptake capacity (about 9 mmol/g). The Ni2+ uptake abilities of the present samples are higher than those of other materials reported in the literature. Since the sorbed Ni2+/released Ca2+ ratios of these samples are close to unity, ion replacement of Ni2+ for Ca2+ is thought to be the principal mechanism of Ni2+ uptake by the present samples.

SiO2-coated LiNi0.915Co0.075Al0.01O2 cathode material for rechargeable Li-ion batteries.

Science.gov (United States)

Zhou, Pengfei; Zhang, Zhen; Meng, Huanju; Lu, Yanying; Cao, Jun; Cheng, Fangyi; Tao, Zhanliang; Chen, Jun

2016-11-24

We reported a one-step dry coating of amorphous SiO 2 on spherical Ni-rich layered LiNi 0.915 Co 0.075 Al 0.01 O 2 (NCA) cathode materials. Combined characterization of XRD, EDS mapping, and TEM indicates that a SiO 2 layer with an average thickness of ∼50 nm was uniformly coated on the surface of NCA microspheres, without inducing any change of the phase structure and morphology. Electrochemical tests show that the 0.2 wt% SiO 2 -coated NCA material exhibits enhanced cyclability and rate properties, combining with better thermal stability compared with those of pristine NCA. For example, 0.2 wt% SiO 2 -coated NCA delivers a high specific capacity of 181.3 mA h g -1 with a capacity retention of 90.7% after 50 cycles at 1 C rate and 25 °C. Moreover, the capacity retention of this composite at 60 °C is 12.5% higher than that of pristine NCA at 1 C rate after 50 cycles. The effects of SiO 2 coating on the electrochemical performance of NCA are investigated by EIS, CV, and DSC tests, the improved performance is attributed to the surface coating layer of amorphous SiO 2 , which effectively suppresses side reactions between NCA and electrolytes, decreases the SEI layer resistance, and retards the growth of charge-transfer resistance, thus enhancing structural and cycling stability of NCA.

Sputtering yields of Si and Ni from the Ni sub(1-x)Si sub(x) system studied by Rutherford backscattering spectrometry

Energy Technology Data Exchange (ETDEWEB)

Kim, S C; Yamaguchi, S; Kataoka, Y; Iwami, M; Hiraki, A [Osaka Univ., Suita (Japan). Faculty of Engineering; Satou, M; Fujimoto, F

1982-01-01

Sputtering yields of Si and Ni from thin layer films of Ni-Si compounds (Ni sub(1-x)Si sub(x)), including the pure materials (Ni and Si), caused by 5keV Ar/sup +/ ion bombardment were investigated using backscattering spectrometry. The sputtering yield for Si from Ni sub(1-x)Si sub(x) increased with increasing Si concentration. However, there is an abrupt decrease in the yield for Si concentrations above NiSi/sub 2/ to pure Si. This is in clear contrast to the sputtering yield of Ni from Ni sub(1-x)Si sub(x) which increased with increasing Ni concentration monotonously. These results are discussed on the basis of both the difference in the atomic density and the electronic state of the alloy.

Planificación cognitiva en niños con déficit auditivo

Directory of Open Access Journals (Sweden)

Ángela González Vinasco

2008-01-01

Full Text Available Este estudio busca abordar y explorar la habilidad para planificar de los niños con déficit auditivo ante una Situación de Resolución de Problemas (SRP, por medio del uso de las Tecnologías de la Información y la Comunicación (TIC, como una herramienta para acceder, de manera objetiva, a los procesos cognitivos del niño con déficit auditivo, sin demandarle ningún tipo de lenguaje verbal, escrito o por medio de señas. Se analizó el desempeño de 11 niños con déficit auditivo que asisten al Instituto para Niños Ciegos y Sordos del Valle del Cauca, con edades entre 4 y 5 años, quienes utilizan ayudas tecnológicas tales como el implante coclear y audífonos. Se realizó un estudio de carácter descriptivo y transversal a partir de una escala de medición continua, con un análisis de los resultados de tipo cuantitativo y cualitativo. Entre los principales resultados del estudio se encuentran: la presencia de mejoras en el desempeño de los niños a través de los tres intentos que debían realizar para resolver la SRP. Aunque las diferencias inter-intentos no fueron estadísticamente significativas, se observó que los niños con déficit auditivo son capaces de trazarse planes parciales y de utilizar estrategias sofisticadas en la resolución de la tarea. Se concluye sobre la importancia de utilizar instrumentos de recolección de la información, adaptados a las necesidades y características de cada población, al momento de evaluar, describir y potencializar los procesos cognitivos de los niños, en este caso de los niños con déficit auditivo.

The Dy–Ni–Si system as a representative of the rare earth–Ni–Si family: Its isothermal section and new rare-earth nickel silicides

Energy Technology Data Exchange (ETDEWEB)

Yuan, Fang; Mozharivskyj, Y. [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4M1 (Canada); Morozkin, A.V., E-mail: morozkin@general.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow GSP-2, 119992 (Russian Federation); Knotko, A.V. [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow GSP-2, 119992 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Geological Faculty, Moscow State University, Leninskie Gory, Moscow 119992 (Russian Federation); Pani, M.; Provino, A.; Manfrinetti, P. [Institute SPIN-CNR and Dipartimento di Chimica e Chimica Industriale, Università di Genova, Via Dodecaneso 31, 16146 Genova (Italy)

2014-11-15

The Dy–Ni–Si system has been investigated at 1070 K by X-ray and microprobe analysis. The system contains the 12 known compounds DyNi{sub 10}Si{sub 2}, DyNi{sub 5}Si{sub 3}, DyNi{sub 6}Si{sub 6}, DyNi{sub 4}Si, DyNi{sub 2}Si{sub 2}, Dy{sub 2}Ni{sub 3}Si{sub 5}, DyNiSi{sub 3}, Dy{sub 3}Ni{sub 6}Si{sub 2}, DyNiSi{sub 2}, DyNiSi, Dy{sub 3}NiSi{sub 3}, Dy{sub 3}NiSi{sub 2}, and the new compounds Dy{sub 34}Ni{sub 16−27}Si{sub 50−39} (AlB{sub 2}-type), Dy{sub 2}Ni{sub 15.2−14.1}Si{sub 1.8−2.9} (Th{sub 2}Zn{sub 17}-type), ∼Dy{sub 11}Ni{sub 65}Si{sub 24}, ∼Dy{sub 16}Ni{sub 62}Si{sub 22} (unknown structures), DyNi{sub 7}Si{sub 6} (GdNi{sub 7}Si{sub 6}-type), Dy{sub 3}Ni{sub 8}Si (Ce{sub 3}Co{sub 8}Si-type), DyNi{sub 2}Si (YPd{sub 2}Si-type), ∼Dy{sub 40}Ni{sub 47}Si{sub 13} and ∼Dy{sub 5}Ni{sub 2}Si{sub 3} (unknown structures). Quasi–binary solid solutions were detected at 1070 (870 K) for Dy{sub 2}Ni{sub 17}, DyNi{sub 5}, DyNi{sub 7}, DyNi{sub 3}, DyNi{sub 2}, DyNi, DySi{sub 2} and DySi{sub 1.67}. No detectable solubility is observed for the other binary compounds of the Dy–Ni–Si system. The crystal structures of new phases RNi{sub 7}Si{sub 6} (GdNi{sub 7}Si{sub 6}-type), R{sub 3}Ni{sub 8}Si (Ce{sub 3}Co{sub 8}Si-type), RNi{sub 2}Si (YPd{sub 2}Si-type) and R{sub 3}Ni{sub 12}Si{sub 4} (Gd{sub 3}Ru{sub 4}Al{sub 12}-type), with R=Y, Gd–Tm, has been studied. Magnetic properties of few representative compounds are also reported. - Graphical abstract: The Dy–Ni–Si system has been investigated at 1070 K by X-ray and microprobe analysis. The system contains the 12 known compounds DyNi{sub 10}Si{sub 2}, DyNi{sub 5}Si{sub 3}, DyNi{sub 6}Si{sub 6}, DyNi{sub 4}Si, DyNi{sub 2}Si{sub 2}, Dy{sub 2}Ni{sub 3}Si{sub 5}, DyNiSi{sub 3}, Dy{sub 3}Ni{sub 6}Si{sub 2}, DyNiSi{sub 2}, DyNiSi, Dy{sub 3}NiSi{sub 3}, Dy{sub 3}NiSi{sub 2}, and the new compounds Dy{sub 34}Ni{sub 16−27}Si{sub 50−39}, Dy{sub 2}Ni{sub 15.2−14.1}Si{sub 1.8−2.9}, ∼Dy{sub 11}Ni{sub 65

Calculation of Gibbs energy of Zr-Al-Ni, Zr-Al-Cu, Al-Ni-Cu and Zr-Al-Ni-Cu liquid alloys based on quasiregular solution model

International Nuclear Information System (INIS)

Li, H.Q.; Yang, Y.S.; Tong, W.H.; Wang, Z.Y.

2007-01-01

With the effects of electronic structure and atomic size being introduced, the mixing enthalpy as well as the Gibbs energy of the ternary Zr-Al-Cu, Ni-Al-Cu, Zr-Ni-Al and quaternary Zr-Al-Ni-Cu systems are calculated based on quasiregular solution model. The computed results agree well with the experimental data. The sequence of Gibbs energies of different systems is: G Zr-Al-Ni-Cu Zr-Al-Ni Zr-Al-Cu Cu-Al-Ni . To Zr-Al-Cu, Ni-Al-Cu and Zr-Ni-Al, the lowest Gibbs energy locates in the composition range of X Zr 0.39-0.61, X Al = 0.38-0.61; X Ni = 0.39-0.61, X Al = 0.38-0.60 and X Zr = 0.32-0.67, X Al = 0.32-0.66, respectively. And to the Zr-Ni-Al-Cu system with 66.67% Zr, the lowest Gibbs energy is obtained in the region of X Al = 0.63-0.80, X Ni = 0.14-0.24

Nivel de conocimiento y su relación con la violencia familiar en padres de niños asistentes al CMI Enrique Martín Altura - 2015

OpenAIRE

Chamamé Ampuero, Eva Verónica

2015-01-01

OBJETIVO: Determinar la relación entre el conocimiento y la violencia familiar en padres de niños asistentes al consultorio de crecimiento y desarrollo del CMI Enrique Martín Altuna durante setiembre de 2015. MÉTODOS: Se llevó a cabo un estudio cuantitativo de tipo descriptivo y de corte transversal con 180 padres de niños del CMI Enrique Martín Altuna durante setiembre del 2015. En la recolección de los datos se utilizó un cuestionario con 22 preguntas: 20 sobre con...

Planificación cognitiva en niños con déficit auditivo

OpenAIRE

Ángela González Vinasco; Natalia Herrera; Diana Carolina Marín Tobón; Tatiana Rojas Ospina

2008-01-01

Este estudio busca abordar y explorar la habilidad para planificar de los niños con déficit auditivo ante una Situación de Resolución de Problemas (SRP), por medio del uso de las Tecnologías de la Información y la Comunicación (TIC), como una herramienta para acceder, de manera objetiva, a los procesos cognitivos del niño con déficit auditivo, sin demandarle ningún tipo de lenguaje verbal, escrito o por medio de señas. Se analizó el desempeño de 11 niños con déficit auditivo que asisten al In...

Interdiffusion studies on high-Tc superconducting YBa2Cu3O7-δ thin films on Si(111) with a NiSi2/ZrO2 buffer layer

DEFF Research Database (Denmark)

Aarnink, W.A.M.; Blank, D.H.A.; Adelerhof, D.J.

1991-01-01

Interdiffusion studies on high-T(c) superconducting YBa2Cu3O7-delta thin films with thickness in the range of 2000-3000 angstrom, on a Si(111) substrate with a buffer layer have been performed. The buffer layer consists of a 400 angstrom thick epitaxial NiSi2 layer covered with 1200 angstrom...... of polycrystalline ZrO2. YBa2Cu3O7-delta films were prepared using laser ablation. The YBa2Cu3O7-delta films on the Si/NiSi2/ZrO2 substrates are of good quality; their critical temperatures T(c,zero) and T(c,onset) have typical values of 85 and 89 K, respectively. The critical current density j(c) at 77 K equaled 4...... x 10(4) A/cm2. With X-ray analysis (XRD), only c-axis orientation has been observed. The interdiffusion studies, using Rutherford backscattering spectrometry (RBS) and scanning Auger microscopy (SAM) show that the ZrO2 buffer layer prevents severe Si diffusion to the YBa2Cu3O7-delta layer, the Si...

Crystal structures of Ni sup 2 sup + -and Tl sup + -exchanged zeolite X, Ni sub 1 sub 7 Tl sub 5 sub 8 Si sub 1 sub 0 sub 0 Al sub 9 sub 2 O sub 3 sub 8 sub 4 and Ni sub 1 sub 2 Tl sub 6 sub 8 Si sub 1 sub 0 sub 0 Al sub 9 sub 2 O sub 3 sub 8 sub 4

CERN Document Server

Song, M K; Kim, Y

2001-01-01

The crystal structures of fully dehydrated Ni sup 2 sup + - and Tl sup + -exchanged zeolite X (Ni sub 1 sub 7 Tl sub 5 sub 8 -X, and Ni sub 1 sub 2 Tl sub 6 sub 8 -X; X=Si sub 1 sub 0 sub 0 Al sub 9 sub 2 O sub 3 sub 8 sub 4) have been determined by single-crystal X-ray diffraction techniques in the cubic space group Fd3 at 21(1) .deg. C (a=24.380(4) A, 24.660(4) A, respectively). Their structures have been refined to the final error indices R sub 1 =0.037 and R sub 2 =0.043 with 485 reflections, and R sub 1 =0.039 and R sub 2 =0.040 with 306 reflections, respectively, for which I>3 sigma(I). In Ni sub 1 sub 7 Tl sub 5 sub 8 -X, 17 Ni sup 2 sup + ions per unit cell were found at only two sites: 15 at site I at the center of the hexagonal prism (Ni-O=2.203(9) A). and the remaining 2 at site II near single six-oxygen rings in the supercage (Ni-O=2.16(3) A). Fifty-eight Tl sup + ions were found at five crystallographic sites: 28 at site II (Tl-O=2.626(8) A, 2 at site I' in the sodalite cavity near the hexagonal ...

MICROSTRUCTURAL ANALYSIS OF Al-Mg-Si-Zn ALLOY

Directory of Open Access Journals (Sweden)

SERGIO VALADEZ

2010-01-01

Full Text Available En un esfuerzo por desarrollar una nueva aleación con aplicación estructural, se ha desarrollado una aleación base Aluminio aleada con magnesio, silicio y zinc. La investigación pretende correlacionar la microestructura y con el tratamiento térmico. La aleación AlMgSiZn, fue elegida para ese propósito debido a la presencia de precipitados tanto en la matriz del aAl, como en los límites de grano, los cuales permiten una excelente relación entre la dureza y la resistencia mecánica. En lo que respecta a la microestructura, esta fue caracterizada bajo condición de colada y después de ser tratada térmicamente por envejecimiento. Este tratamiento fue realizado en dos etapas, la primera a 450ºC durante 3 horas que corresponde al tratamiento de homogeneización: y la segunda al proceso de envejecimiento artificial llevado a cabo a 160ºC durante 1hr. Los resultados indican la presencia de dendritas de aAl, además un eutéctico binario y partículas de Mg7Zn3 adentro de las regiones interdendríticas. El eutéctico y las partículas fueron modificados por el tratamiento de envejecido. Las observaciones realizadas con el microscopio electrónico de transmisión en especímenes con y sin tratamientos térmicos, demostraron una distribución uniforme de precipitados con diversas morfologías, tales como cúbico, esférico y plaqueta: para la matriz de aAl, los cuales no fueron detectados durante las observaciones en el microscopio electrónico de barrido.

Survey of trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) in retail samples of flavoured and bottled waters.

Science.gov (United States)

Barroso, M F; Ramos, S; Oliva-Teles, M T; Delerue-Matos, C; Sales, M G F; Oliveira, M B P P

2009-01-01

Concentrations of eleven trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) were measured in 39 (natural and flavoured) water samples. Determinations were performed using graphite furnace electrothermetry for almost all elements (Al, As, Cd, Cr, Co, Mn, Ni, Pb, and Si). For Se determination hydride generation was used, and cold vapour generation for Hg. These techniques were coupled to atomic absorption spectrophotometry. The trace element content of still or sparkling natural waters changed from brand to brand. Significant differences between natural still and natural sparkling waters (p element was compared with the presence of flavours, preservatives, acidifying agents, fruit juice and/or sweeteners, according to the labelled composition. It was shown that flavoured waters generally increase the trace element content. The addition of preservatives and acidifying regulators had a significant influence on Mn, Co, As and Si contents (p < 0.05). Fruit juice can also be correlated to the increase of Co and As. Sweeteners did not provide any significant difference in Mn, Co, Se and Si content.

Addition of iron for the removal of the {beta}-AlFeSi intermetallic by refining of {alpha}-AlFeSi phase in an Al-7.5Si-3.6Cu alloy

Energy Technology Data Exchange (ETDEWEB)

Belmares-Perales, S. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon (Mexico); Zaldivar-Cadena, A.A., E-mail: azaldiva70@hotmail.com [Facultad de Ingenieria Civil, Departamento de Ecomateriales y Energia, Instituto de Ingenieria Civil, Av. Fidel Velasquez and Av. Universidad S/N, Cd. Universitaria, San Nicolas de los Garza, N.L. 66450 (Mexico)

2010-10-25

Addition of iron into the molten metal for the removal of the {beta}-AlFeSi intermetallic by refining of {alpha}-AlFeSi phase has been studied. Solidification conditions and composition determine the final microstructure and mechanical properties of a casting piece. It is known that increasing the iron content will produce an increasing of the {alpha}-AlFeSi and {beta}-AlFeSi phases. This phenomenon was confirmed with calculations made by Thermo-Calc{sup TM} software and validated with experimental results, however, the technique of iron addition in this study plays an important role on the solidification kinetics of these iron phases because the refining of {alpha}-AlFeSi and removal of {beta}-AlFeSi phases can be improved. Final results showed an improvement in mechanical properties by removal and refining of {beta}-AlFeSi and {alpha}-AlFeSi phases, respectively. This study shows a new method of removal of {beta}-AlFeSi that could be adopted in the aluminum smelting industry in aluminum alloys with a low cooling rate with a secondary dendritic spacing of about 37 {mu}m.

Addition of iron for the removal of the β-AlFeSi intermetallic by refining of α-AlFeSi phase in an Al-7.5Si-3.6Cu alloy

International Nuclear Information System (INIS)

Belmares-Perales, S.; Zaldivar-Cadena, A.A.

2010-01-01

Addition of iron into the molten metal for the removal of the β-AlFeSi intermetallic by refining of α-AlFeSi phase has been studied. Solidification conditions and composition determine the final microstructure and mechanical properties of a casting piece. It is known that increasing the iron content will produce an increasing of the α-AlFeSi and β-AlFeSi phases. This phenomenon was confirmed with calculations made by Thermo-Calc TM software and validated with experimental results, however, the technique of iron addition in this study plays an important role on the solidification kinetics of these iron phases because the refining of α-AlFeSi and removal of β-AlFeSi phases can be improved. Final results showed an improvement in mechanical properties by removal and refining of β-AlFeSi and α-AlFeSi phases, respectively. This study shows a new method of removal of β-AlFeSi that could be adopted in the aluminum smelting industry in aluminum alloys with a low cooling rate with a secondary dendritic spacing of about 37 μm.

Magnetic properties of two new compounds: Pr2Ni3Si5 and Ho2Ni3Si5

International Nuclear Information System (INIS)

Mazumdar, C.; Padalia, B.D.; Godart, C.

1994-01-01

Formation of two more new materials, Pr 2 Ni 3 Si 5 and Ho 2 Ni 3 Si 5 , of the series, R 2 Ni 3 Si 5 (R = rare earth and Y) and their magnetic properties are reported here. These materials crystallize in the orthorhombic U 2 Co 3 Si 5 -type structure (space group Ibam). Magnetic susceptibility measurement in the temperature range 5 K--300 K show that the compound Pr 2 Ni 3 Si 5 order antiferromagnetically at T N ∼ 8.5 K and Ho 2 Ni 3 Si 5 at ∼ 6 K. Considering T N (Gd 2 Ni 3 Si 5 ) ∼ 15 K, T N (Pr 2 Ni 3 Si 5 ) ∼ 8.5 K is rather high. The magnetic susceptibility of both of the materials, in the paramagnetic state, follows a Curie-Weiss law with effective moment close to that of the corresponding free trivalent rare earth ion

Prevalencia de trombocitopenia en niños con HIV/sida

Directory of Open Access Journals (Sweden)

Graciela Barboni

2010-10-01

Full Text Available La trombocitopenia es una de las múltiples alteraciones hematológicas presentes en pacientes infectados con el virus de la inmunodeficiencia humana (HIV. Puede ser de curso crónico, en la cual la destrucción inmune, el secuestro esplénico o el daño en la producción son los mecanismos primariamente involucrados, o aguda, acompañando a otra intercurrencia. En este trabajo se evaluó la prevalencia de trombocitopenia en un lapso de 14 años, en una población pediátrica con HIV/sida, analizando las características clínicas y la relación con el estado inmuno-virológico. La prevalencia de trombocitopenia fue de 8.5%, (29 de los 339 niños en seguimiento. En 22 fue de curso crónico y en 7 aguda. Los pacientes evaluados presentaron niveles porcentuales de TCD4+ variables y la presencia de trombocitopenia no estuvo en relación con el compromiso inmunitario. Los pacientes trombocitopénicos tuvieron niveles de carga viral significativamente mayores que los que no la presentaron. En 10 de los 29 niños con recuentos plaquetarios disminuidos, la trombocitopenia fue la manifestación inicial de la infección por HIV. Las manifestaciones hemorrágicas de las trombocitopenias crónicas fueron leves, presentes en el 23% de los niños y no se asociaron al deterioro inmunológico, mientras que en las agudas fueron más graves y condicionadas a la evolución de la enfermedad coexistente. El desarrollo de trombocitopenias se ve favorecido por la continua actividad viral y la falla en la implementación del tratamiento antirretroviral adecuado.

Glass forming ability of the Al-Ce-Ni system; Avaliacao da capacidade de formacao vitrea do sistema Al-Ce-Ni

Energy Technology Data Exchange (ETDEWEB)

Triveno Rios, C. [Engenharia Mecanica, Universidade Federal de Mato Grosso, Rondonopolis, MT (Brazil)], e-mail: triveno@ufmt.br; Surinach, S.; Baro, M.D. [Departamento de Engenharia de Materiais - Universidade Federal de Sao Carlos, SP (Brazil); Bolfarini, C.; Botta, W.J.; Kiminami, C.S. [Departamento de Fisica da Universidade Autonoma de Barcelona, Bellaterra (Spain)

2010-07-01

In the present work, the glass forming ability (GFA) and its compositional dependence on Al-Ni-Ce system alloys were investigated in function of several thermal parameters. Rapidly quenched Al{sub 85}Ni{sub 15}-{sub X}Ce{sub X} (X=4,5,6,7,10), Al{sub 90}Ni{sub 5}Ce{sub 5}, Al{sub 89}Ni{sub 2}.{sub 4}Ce{sub 8}.{sub 6}, Al{sub 80}Ni{sub 15.6}Ce{sub 4}.{sub 4} and Al{sub 78}Ni{sub 18.5}Ce{sub 3.5} amorphous ribbons were produced by melt-spinning and the structural transformation during heating was studied using a combination of X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The results showed that the GFA and the thermal stability in the Al-rich corner of Al- Ni-Ce system alloys were enhanced by increasing the solute content and specifically the Ce content (author)

Effects of Alloying Elements on Room and High Temperature Tensile Properties of Al-Si Cu-Mg Base Alloys =

Science.gov (United States)

Alyaldin, Loay

result of the presence of both Mg and Cu. These alloy types display excellent strength values at both low and high temperatures. Additions of Zr, Ni, Mn and Sc would be expected to maintain the performance of these alloys at still higher temperatures. Six alloys were prepared using 0.2 wt% Ti grain-refined 354 alloy, comprising alloy R (354 + 0.25wt% Zr) considered as the base or reference alloy, and five others, viz., alloys S, T, U, V, and Z containing various amounts of Ni, Mn, Sc and Zr, added individually or in combination. For comparison purposes, another alloy L was prepared from 398 (Al-16%Si) alloy, reported to give excellent high temperature properties, to which the same levels of Zr and Sc additions were made, as in alloy Z. Tensile test bars were prepared from the different 354 alloys using an ASTM B-108 permanent mold. The test bars were solution heat treated using a one-step or a multi-step solution heat treatment, followed by quenching in warm water, and then artificial aging employing different aging treatments (T5, T6, T62 and T7). The one-step (or SHT 1) solution treatment consisted of 5 h 495 °C) and the multi-step (or SHT 2) solution treatment comprised 5 h 495°C + 2 h 515°C + 2 h 530°C. Thermal analysis of the various 354 alloy melts was carried out to determine the sequence of reactions and phases formed during solidification under close-to-equilibrium cooling conditions. The main reactions observed comprised formation of the alpha-Al dendritic network at 598°C followed by precipitation of the Al-Si eutectic and post-eutectic beta-Al5FeSi phase at 560°C; Mg2Si phase and transformation of the beta-phase into pi-Al8Mg 3FeSi6 phase at 540°C and 525°C; and lastly, precipitation of Al2Cu and Q-Al5Mg8Cu2Si 6 almost simultaneously at 498°C and 488°C. Larger sizes of AlFeNi and AlCuNi phase particles were observed in T alloy with its higher Ni content of 4 wt%, when compared to those seen in S alloy at 2% Ni content. Mn addition in Alloy U helps

Phase Evolution and Mechanical Properties of AlCoCrFeNiSi x High-Entropy Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Science.gov (United States)

Kumar, Anil; Swarnakar, Akhilesh Kumar; Chopkar, Manoj

2018-05-01

In the current investigation, AlCoCrFeNiSi x (x = 0, 0.3, 0.6 and 0.9 in atomic ratio) high-entropy alloy systems are prepared by mechanical alloying and subsequently consolidated by spark plasma sintering. The microstructural and mechanical properties were analyzed to understand the effect of Si addition in AlCoCrFeNi alloy. The x-ray diffraction analysis reveals the supersaturated solid solution of the body-centered cubic structure after 20 h of ball milling. However, the consolidation promotes the transformation of body-centered phases partially into the face-centered cubic structure and sigma phases. A recently proposed geometric model based on the atomic stress theory has been extended for the first time to classify single phase and multi-phases on the high-entropy alloys prepared by mechanical alloying and spark plasma sintering process. Improved microhardness and better wear resistance were achieved as the Si content increased from 0 to 0.9 in the present high-entropy alloy.

Microporous Ni@NiO nanoparticles prepared by chemically dealloying Al{sub 3}Ni{sub 2}@Al nanoparticles as a high microwave absorption material

Energy Technology Data Exchange (ETDEWEB)

Pang, Yu; Xie, Xiubo; Li, Da [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, No.37 Xueyuan Road, Beijing 100191 (China); Chou, Wusheng [School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China); Liu, Tong, E-mail: tongliu@buaa.edu.cn [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, No.37 Xueyuan Road, Beijing 100191 (China)

2017-03-15

The Al{sub 3}Ni{sub 2}@Al nanoparticles (NPs) were prepared from Ni{sub 45}Al{sub 55} master alloy by hydrogen plasma-metal reaction method, and were subsequently dealloyed to produce porous Ni@NiO NPs of 36 nm. The pore size ranges from 0.7 to 1.6 nm, leading to large specific surface area of 69.5 m{sup 2}/g and big pore volume of 0.507 cc/g. The saturation magnetization (M{sub S}) and coercivity (H{sub C}) of the microporous Ni@NiO NPs are 11.5 emu/g and 5.2 Oe. They exhibit high microwave absorption performance with a minimum reflection coefficient (RC) of −86.9 dB and an absorption bandwidth of 2.6 GHz (RC≤−10 dB) at thickness of 4.5 mm. The enhanced microwave absorption properties are attributed to the synergistic effect of the magnetic Ni core and dielectric NiO shell, and the micropore architecture. The NPs with micropore morphology and core/shell structure open a new way to modify the microwave absorption performance. - Graphical abstract: The microporous Ni/NiO nanoparticles prepared by chemically dealloying Al{sub 3}Ni{sub 2}@Al NPs exhibit high microwave absorption intensity (−86.9 dB) and wide absorption bandwidth (2.6 GHz for RC≤−10 dB). - Highlights: • Microporous Ni/NiO nanoparticals were prepared by chemically dealloying method. • They possessed micropores of 0.7–1.6 nm with a surface area of 69.5 m{sup 2}/g. • They showed high microwave absorption intensity and wide absorption bandwidth. • Microwave absorption mechanism was explained by micropore and core/shell structures.

Correlation between the electrical properties and the interfacial microstructures of TiAl-based ohmic contacts to p-type 4H-SiC

Science.gov (United States)

Tsukimoto, S.; Nitta, K.; Sakai, T.; Moriyama, M.; Murakami, Masanori

2004-05-01

In order to understand a mechanism of TiAl-based ohmic contact formation for p-type 4H-SiC, the electrical properties and microstructures of Ti/Al and Ni/Ti/Al contacts, which provided the specific contact resistances of approximately 2×10-5 Ω-cm2 and 7×10-5 Ω-cm2 after annealing at 1000°C and 800°C, respectively, were investigated using x-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Ternary Ti3SiC2 carbide layers were observed to grow on the SiC surfaces in both the Ti/Al and the Ni/Ti/Al contacts when the contacts yielded low resistance. The Ti3SiC2 carbide layers with hexagonal structures had an epitaxial orientation relationship with the 4H-SiC substrates. The (0001)-oriented terraces were observed periodically at the interfaces between the carbide layers and the SiC, and the terraces were atomically flat. We believed the Ti3SiC2 carbide layers primarily reduced the high Schottky barrier height at the contact metal/p-SiC interface down to about 0.3 eV, and, thus, low contact resistances were obtained for p-type TiAl-based ohmic contacts.

Ca2 Al2 SiO7 :Ce3+ phosphors for mechanoluminescence dosimetry.

Science.gov (United States)

Tiwari, Geetanjali; Brahme, Nameeta; Sharma, Ravi; Bisen, D P; Sao, Sanjay Kumar; Sahu, Ishwar Prasad

2016-12-01

A series of Ce 3+ ion single-doped Ca 2 Al 2 SiO 7 phosphors was synthesized by a combustion-assisted method at an initiating temperature of 600 °C. The samples were annealed at 1100 °C for 3 h and their X-ray diffraction patterns confirmed a tetragonal structure. The phase structure, particle size, surface morphology and elemental analysis were analyzed using X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy techniques. Thermoluminescence (TL) intensity increased with increase in ultraviolet (UV) light exposure time up to 15 min. With further increase in the UV irradiation time the TL intensity decreases. The increase in TL intensity indicates that trap concentration increased with UV exposure time. A broad peak at 121 °C suggested the existence of a trapping level. The peak of mechanoluminescence (ML) intensity versus time curve increased linearly with increasing impact velocity of the moving piston. Mechanoluminescence intensity increased with increase in UV irradiation time up to 15 min. Under UV-irradiation excitation, the TL and ML emission spectra of Ca 2 Al 2 SiO 7 :Ce 3+ phosphor showed the characteristic emission of Ce 3+ peaking at 400 nm (UV-violet) and originating from the Ce 3+ transitions of 5d-4f ( 2 F 5/2 and 2 F 7/2 ). The photoluminescence (PL) emission spectra for Ca 2 Al 2 SiO 7 :Ce 3+ were similar to the ML/TL emission spectra. The mechanism of ML excitation and the suitability of the Ca 2 Al 2 SiO 7 :Ce 3+ phosphor for radiation dosimetry are discussed. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Magnetic and transport properties of EuNi(Si1-xGex)3 compounds

International Nuclear Information System (INIS)

Uchima, K; Takaesu, Y; Akamine, H; Kakihana, M; Tomori, K; Uejo, T; Teruya, A; Nakamura, A; Hedo, M; Nakama, T; Yagasaki, K; Matsubayashi, K; Uwatoko, Y

2014-01-01

The magnetization M, electrical resistivity ρ, thermopower S and specific heat C of EuNi(Si 1-x Ge x ) 3 compounds have been measured at temperatures from 2 to 300 K. For the compounds of EuNi(Si 1-x Ge x ) 3 , we obtained an effective magnetic moment of μ eff ∼ 7.7 μ B , which is close to the divalent Eu value of μ eff =7.94 μ B . All compounds of EuNi(Si 1-x Ge x ) 3 order antiferromagnetically. The Néel temperature T N decreases monotonously with increasing the Ge concentration x from T N =49 K for EuNiSi 3 to T N =14 K for EuNiGe 3 . In the low temperature region below T N , anomalies corresponding to an additional magnetic phase transition into ferromagnetic state for compounds with x < 0.3, and into another antiferromagnetic for x > 0.3 were observed. The Curie temperature T C rapidly decreases with increasing x and vanishes at x ≈ 0.3. It is found that the magnetic phase transition temperatures of T N and T C in EuNi(Si 1-x Ge x ) 3 are strongly connected with the change of volume induced by the atomic substitution of Si by Ge

Depósito electroquímico de recubrimientos compuestos de Ni-SiC y evaluación de su comportamiento anticorrosivo

Directory of Open Access Journals (Sweden)

Johny Edwar Henao Guzmán

2009-01-01

Full Text Available En el presente estudio se reporta la obtención de recubrimientos de Ni puro y compuestos de Ni con partículas nanométricas de SiC. Los recubrimientos fueron depositados sobre sustratos de acero al carbono AISI-SAE 1016 mediante polarización lineal sobre un electrodo de disco rotatorio, variando la velocidad de rotación y el contenido de partículas de SiC en el baño. Los recubrimientos fueron obtenidos a partir de una solución tipo Watts clásica, en la cual se adicionaron nanopartículas de SiC. Las propiedades anticorrosivas de los recubrimientos se estudiaron mediante técnicas electroquímicas y ensayos de corrosión-erosión. La microestructura de los recubrimientos se estudió mediante microscopía óptica. Se encontró que a medida que aumenta la cantidad de partículas en los recubrimientos aumenta la nobleza y la resistencia a la corrosión-erosión de los mismos. De la misma manera las propiedades mecánicas de los recubrimientos mejoran notablemente con el incremento de la cantidad de partícula en el depósito y con el aumento de la velocidad de agitación del baño durante la electrodeposición.

Erupción dentaria: estudio radiográfico de corredores de erupción de caninos superiores en niños con 10 años de edad.

Directory of Open Access Journals (Sweden)

Fernando Aguilera Zurira

2014-12-01

Full Text Available Las características anatómicas del canino superior lo convierten en el diente con mayor potencial de supervivencia en la arcada. Desde un punto de vista funcional, los caninos son considerados dientes claves en la oclusión. Con un gran protagonismo estético, dan armonía al frente anterior y la línea de la sonrisa. La erupción de los caninos superiores debe ser observada con frecuencia ya que es el diente en segundo lugar que presenta alteraciones en su erupción después de los terceros molares, este seguimiento se debe realizar con observaciones clínicas como radiográficas para tener la posibilidad de ir guiando el trayecto de erupción. Desde los 8 a 10 años de edad empieza a palparse la prominencia del canino en el fondo del vestíbulo. Si no se palpa a los 10 años, está indicado realizar un estudio radiológico para valorar la posición y reabsorción radicular del canino temporal. En este trabajo se realizó un estudio descriptivo en radiografías panorámicas en niños con 10 años de edad de ambos sexos de la ciudad de Quito, con el objetivo de analizar los corredores de erupción de caninos superiores, así como observar e interpretar la situación de los caninos superiores y su relación con las estructuras vecinas, describir las curvas y columnas de erupción en caninos superiores, para determinar si existe alteraciones y diferencias en cuanto a la erupción de los caninos definitivos en relación al sexo de los niños evaluados. La muestra estuvo constituida por 60 niños (30 hombres y 30 mujeres. De este grupo en cuanto a corredores de erupción se estableció que un 12% corresponde a curvas entrelazadas y un 7% a interrumpidas, estableciendo que el control clínico es fundamental y el seguimiento radiográfico secuencial permitirá ir revisando la evolución de la erupción de los caninos superiores y estructuras adyacentes. En cuanto a las columnas de erupción se determinó que el 2% de la muestra se encuentra en la

Creep Properties of NiAl-1Hf Single Crystals Re-Investigated

Science.gov (United States)

Whittenberger, J. Daniel; Locci, Ivan E.; Darolia, Ram; Bowman, Randy R.

2000-01-01

ingots were subjected to several heat treatment schedules, examined by transmission electron microscopy, and tested in both compression and tension. An example of the microstructure found in a [001]-oriented NiAl-1Hf specimen after a solution treatment at 1317 C for 50 hr followed by air cooling is illustrated in the image on the left, where the NiAl matrix contains a uniform distribution of nanometer-scale Gphase (Ni16Hf6Si7) precipitates. Other heat treating schedules produced microstructures with nanometer-sized G-phase cubes and plates or, in an extreme case, produced a microstructure with all the G-phase converted to Heusler (Ni2AlHf) particles. The results of 1027 C creep strength and strain rate testing are illustrated which summarizes data from tensile and compressive testing of samples cut from all four NiAl-1Hf ingots and subjected to a variety of heat treatment schedules. With one exception, all the strength values lie in a narrow band that spans six orders of magnitude in strain rate. The only factor that produced results outside of this band was the heat treatment schedule that dissolved all the G-phase and replaced it with Heusler precipitates. The results portrayed in this figure lead to the important practical conclusion that the elevated-temperature creep properties of NiAl-1Hf single crystals are reproducible and are not affected by small variations in alloy chemistry from ingot to ingot or by different initial distributions of G-phase in the heat-treated alloy. The only variable in this study that produced a significant and delerious effect on mechanical strength was a post-solution heat treatment that lead to the complete disappearance of the G-phase in favor of Heusler precipitates.

A study on the composition optimization and mechanical properties of Al-Mg-Si cast alloys

International Nuclear Information System (INIS)

Zhang, X.H.; Su, G.C.; Han, Y.Y.; Ai, X.H.; Yan, W.L.

2010-01-01

The mechanical properties of Al-Mg-Si cast alloys with different chemical compositions were investigated using an orthogonal test method. The optimized chemical compositions of Al alloy are given in wt% as follows: 7.0%Si-0.35%Mg-2.0%Cu-0.2%Mn-0.2%Ni-0.1%V-0.8%RE-89.35%Al. The optimized Al-Mg-Si alloy with metal mold casting had excellent mechanical properties. The softening resistance of the optimized alloy was better than that of ZL101 at elevated temperatures. The scanning electron microscopy fractographs of the tensile samples of ZL101 and optimized Al alloy at different magnifications revealed that all the specimens were fractured in a ductile manner, consisting of well-developed dimples over the entire surface. The alloys failed in a mixed-mode fracture, comprised predominantly of transgranular shears and a small amount of quasi-cleavages.

Structure of Ni-rich Ni--Cr--B--Si coating alloys

International Nuclear Information System (INIS)

Knotek, O.; Lugscheider, E.; Reimann, H.

1975-01-01

The structures of quaternary, nickel-rich Ni--Cr--B--Si alloys were analyzed at a constant boron content of 10 at. percent and a temperature of 850 0 C. The composition range for silicide formation was determined. In these quaternary alloys, known binary nickel silicides, nickel and chromium borides, and the ternary silico-boride Ni 6 Si 2 B were confirmed. A new composition for the W 5 Si 3 -type phase in the Ni--B--Si system was proposed. (U.S.)

Thermal and mechanical properties of the Zr53Cu30Ni9Al8 based bulk metallic glass microalloyed with silicon

International Nuclear Information System (INIS)

Jang, Jason S.C.; Jian, S.R.; Chang, C.F.; Chang, L.J.; Huang, Y.C.; Li, T.H.; Huang, J.C.; Liu, C.T.

2009-01-01

The amorphous alloy rods of (Zr 53 Cu 30 Ni 9 Al 8 ) 100-x Si x (x = 0.25, 0.5, 0.75, 1) with a diameter of 2-6 mm were prepared by drop casting method in an Ar atmosphere. The thermal properties, including glass forming ability (GFA) and thermal stability during isothermal annealing of these amorphous alloys, and the mechanical properties have been systematic investigated by the combination of DSC, XRD, SEM, TEM, and compression test. The result of X-ray diffraction reveals that these entire (Zr 53 Cu 30 Ni 9 Al 8 ) 100-x Si x alloy rods exhibit a typical amorphous diffraction pattern with only a broad maximum around 2θ around 40 degree. Both T g (glass transition temperature) and T x (crystallization temperature) of these (Zr 53 Cu 30 Ni 9 Al 8 ) 100-x Si x alloys increase with the silicon addition. In addition, both the activation energy of crystallization and the incubation time of isothermal annealing these (Zr 53 Cu 30 Ni 9 Al 8 ) 100-x Si x amorphous alloys indicate that the (Zr 53 Cu 30 Ni 9 Al 8 ) 99.25 Si 0.75 alloy possesses the best thermal stability in the (Zr 53 Cu 30 Ni 9 Al 8 ) 100-x Si x alloy system. In parallel, the result of compression test shows that the yield strength increases with the addition of Si content and reaches to a maximum value about 1750 MPa with 3% plastic strain for the (Zr 53 Cu 30 Ni 9 Al 8 ) 99.25 Si 0.75 amorphous alloy.

Alloying behavior, microstructure and mechanical properties in a FeNiCrCo0.3Al0.7 high entropy alloy

International Nuclear Information System (INIS)

Chen, Weiping; Fu, Zhiqiang; Fang, Sicong; Xiao, Huaqiang; Zhu, Dezhi

2013-01-01

Highlights: • FeNiCrCo 0.3 Al 0.7 high entropy alloy is prepared via MA and SPS. • Two BCC phases and one FCC phase were obtained after SPS. • The two BCC phases are enriched in Fe–Cr (A2 structure) and enriched in Ni–Al (B2 structure). • Bulk FeNiCrCo 0.3 Al 0.7 HEA exhibits excellent mechanical properties. - Abstract: The present paper reports the synthesis of FeNiCrCo 0.3 Al 0.7 high entropy alloy (HEA) by mechanical alloying (MA) and spark plasma sintering (SPS) process. Alloying behavior, microstructure, mechanical properties and detailed phases of the alloy were investigated systematically. During MA, the formation of a supersaturated solid solution with body-centered cubic (BCC) structure occurred. However, partial BCC structure phase transformed into a face-center cubic (FCC) structure phase during SPS. Two BCC phases with nearly the same lattice parameter of 3.01 Å and one FCC phase with the lattice parameter of 3.72 Å were characterized in the transmission electron microscope (TEM) images. The two BCC phases which are evidently deviated from the definition of high entropy alloys (HEAs) are enriched in Fe–Cr and enriched in Ni–Al, respectively. Moreover, the FCC phase agrees well with the definition of HEAs. Bulk FeNiCrCo 0.3 Al 0.7 alloy with little porosity exhibits much better mechanical properties except compression ratio compared with other typical HEAs of FeNiCrCoAl HEA system. The yield strength, compressive strength, compression ratio and Vickers hardness of FeNiCrCo 0.3 Al 0.7 alloy are 2033 ± 41 MPa, 2635 ± 55 MPa, 8.12 ± 0.51% and 624 ± 26H v , respectively. The fracture mechanism of bulk FeNiCrCo 0.3 Al 0.7 alloy is dominated by intercrystalline fracture and quasi-cleavage fracture

Effect of TiO2 addition on reaction between SiC and Ni in SiC-Ni cermet spray coatings. Part 2. ; Development of SiC-based cermet spray coatings. SiC-Ni yosha himakuchu no SiC-Ni kaimen hanno ni oyobosu TiO2 tenka no koka. 2. ; SiC-ki sametto yosha himaku no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, T [Kumano Technical College, Mie (Japan); Oki, S; Goda, S [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1992-09-30

The depression of the reaction between SiC and Ni, by adding TiO2 powder in spraying powder which has caused uniform dispersion in spray coating and reduction of TiO2 by the reaction during spraying, was studied. The mass ratio of the mixed components has been, SiC:Ni:TiO2=3:2:1. The spray coating was examined by electron prove microanalysis as well as X-ray diffractometry, centering mainly to the SiC-metal interface reaction. The formation of Ni-Si compounds have been depressed by the addition of TiO2 to spraying powder and by using plasma gas containing H2. Reason for this has been that the TiC formed in the SiC-Ni interface has depressed the reaction at the SiC-Ni interface. Further, TiO2 is reduced during spraying, and TiC is thought to be formed by the reaction between Ti and SiC or reaction between TiO2 and SiC. 8 refs., 6 figs., 1 tab.

On the synthesis and characterization of some new AB{sub 5} type MmNi{sub 4.3}Al{sub 0.3},Mn{sub 0.4}, LaNi{sub 5-{chi}}Si{sub {chi}} ({chi} = 0.1, 0.3, 0.5) and Mg-{chi} wt% CFMmNi{sub 5}-y wt% Si hydrogen storage materials

Energy Technology Data Exchange (ETDEWEB)

Srivistava, S.; Sai Raman, S.S.; Singh, B.K.; Srivistava, O.N. [Banaras Hindu Univ., Varanasi (India). Dept. of Physics

2000-05-01

The viability and feasibility of Hydrogen Energy becoming the clean alternative to Fossil Fuel Energy through replacement of 'Fossil Fuel' with 'Hydrogen' (the Green Fuel) is inextricably interlinked with development of 'Hydrogen Storage Systems'. Out of the high pressure gaseous hydrogen, liquid hydrogen, storage in glass microspheres, activated carbon, zeolites, hydrogen rich liquids and solid state hydrides, the last option is of implicit importance. Out of the AB (e.g., FeTi, storage capacity -- 1.75 wt%), AB{sub 2} or A{sub 2}B (Mg{sub 2}Ni -- 3.8 wt%), AB{sub 5} (LaNi{sub 5}, MmN{sub 5} -- 1.5 wt%) and K{sub 2} PtCl{sub 6} type (Mg{sub 2}FeH{sub 6} -- 5.2 wt%); the AB{sub 5} type holds potential promise due to easy activation, tolerance to impurities of charging H{sub 2} gas and avid amenability towards material tailoring for improved and better hydrogenation characteristics. We have carried out synthesis, characterization of several of the AB{sub 5} type storage materials. The present paper is aimed at describing and discussing some of our more recent efforts in regard to this. In the present study the hydrogen storage material (MH) has been synthesized through normal casting (Radio Frequency (RF) induction melting) and melt-spinning techniques. The improvements in basic alloys LaNi{sub 5}/MmNi{sub 5} have been studied through structural, microstructural and hydrogenation characteristics. The main features revealed by XRD characterizations are the existence of the free Ni and Si together with AB{sub 5} material in melt-spun alloy of LaNi{sub 5-{chi}}Si{sub {chi}}. These free Ni and Si were found to disappear, giving rise to a singular material after hydrogenation. Also in melt-spun alloy growth has taken place in a direction perpendicular to the c-axis. Melt-spun version was found to be superior over bulk version in regard to kinetics and activation process. For MmNi{sub 4.3}AlO{sub 3}Mn{sub 0.4} alloy, melt-spun version has

Electrical and structural properties of surfaces and interfaces in Ti/Al/Ni Ohmic contacts to p-type implanted 4H-SiC

Science.gov (United States)

Vivona, M.; Greco, G.; Bongiorno, C.; Lo Nigro, R.; Scalese, S.; Roccaforte, F.

2017-10-01

In this work, the electrical and structural properties of Ti/Al/Ni Ohmic contacts to p-type implanted silicon carbide (4H-SiC) were studied employing different techniques. With increasing the annealing temperature, an improvement of the electrical properties of the contacts is highlighted, until an Ohmic behavior is obtained at 950 °C, with a specific contact resistance ρc = 2.3 × 10-4 Ω cm2. A considerable intermixing of the metal layers occurred upon annealing, as a consequence of the formation of different phases, both in the uppermost part of the stack (mainly Al3Ni2) and at the interface with SiC, where the formation of preferentially aligned TiC is observed. The formation of an Ohmic contact was associated with the occurrence of the reaction and the disorder at the interface, where the current transport is dominated by the thermionic field emission mechanism with a barrier height of 0.56 eV.

Mechanical properties of Fe-Ni-Cr-Si-B bulk glassy alloy

International Nuclear Information System (INIS)

Lee, Kee Ahn; Kim, Yong Chan; Kim, Jung Han; Lee, Chong Soo; Namkung, Jung; Kim, Moon Chul

2007-01-01

The mechanical properties and crystallization behavior of new Fe-Ni-Cr-Si-B-based bulk glassy alloys were investigated. The suitability of the continuous roll casting method for the production of bulk metallic glass (BMG) sheets in such alloy systems was also examined. BMG samples (Fe-Ni-Cr-Si-B, Fe-Ni-Zr-Cr-Si-B, Fe-Ni-Zr-Cr-W-Si-B) in amorphous strip, cylindrical, and sheet forms were prepared through melt spinning, copper mold casting, and twin roll strip casting, respectively. Fe-Ni-Cr-Si-B alloy exhibited compressive strength of up to 2.93 GPa and plastic strain of about 1.51%. On the other hand, the Fe-Ni-Zr-Cr-Si-B, composite-type bulk sample with diameter of 2.0 mm showed remarkable compressive plastic strain of about 4.03%. The addition of zirconium was found to enhance the homogeneous precipitation of nanocrystalline less than 7 nm and to develop a hybrid-composite microstructure with increasing sample thickness. Twin roll strip casting was successfully applied to the fabrication of sheets in Fe-Ni-Cr-Si-B-based BMGs. The combined characteristics of high mechanical properties and ease of microstructure control proved to be promising in terms of the future progress of structural bulk amorphous alloys

Mechanical properties of Fe-Ni-Cr-Si-B bulk glassy alloy

Energy Technology Data Exchange (ETDEWEB)

Lee, Kee Ahn [School of Advanced Materials Engineering, Andong National University, Andong 760-749 (Korea, Republic of)]. E-mail: keeahn@andong.ac.kr; Kim, Yong Chan [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of); Kim, Jung Han [Center for Advanced Aerospace materials, POSTECH, Pohang 790-784 (Korea, Republic of); Lee, Chong Soo [Center for Advanced Aerospace materials, POSTECH, Pohang 790-784 (Korea, Republic of); Namkung, Jung [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of); Kim, Moon Chul [New Metals Research Team, RIST, Pohang 790-330 (Korea, Republic of)

2007-03-25

The mechanical properties and crystallization behavior of new Fe-Ni-Cr-Si-B-based bulk glassy alloys were investigated. The suitability of the continuous roll casting method for the production of bulk metallic glass (BMG) sheets in such alloy systems was also examined. BMG samples (Fe-Ni-Cr-Si-B, Fe-Ni-Zr-Cr-Si-B, Fe-Ni-Zr-Cr-W-Si-B) in amorphous strip, cylindrical, and sheet forms were prepared through melt spinning, copper mold casting, and twin roll strip casting, respectively. Fe-Ni-Cr-Si-B alloy exhibited compressive strength of up to 2.93 GPa and plastic strain of about 1.51%. On the other hand, the Fe-Ni-Zr-Cr-Si-B, composite-type bulk sample with diameter of 2.0 mm showed remarkable compressive plastic strain of about 4.03%. The addition of zirconium was found to enhance the homogeneous precipitation of nanocrystalline less than 7 nm and to develop a hybrid-composite microstructure with increasing sample thickness. Twin roll strip casting was successfully applied to the fabrication of sheets in Fe-Ni-Cr-Si-B-based BMGs. The combined characteristics of high mechanical properties and ease of microstructure control proved to be promising in terms of the future progress of structural bulk amorphous alloys.

Valoración clínica, psicológica y de laboratorio a niños con hiperfenilalaninemia benigna al nacimiento

Directory of Open Access Journals (Sweden)

Enna Gutiérrez García

2002-12-01

Full Text Available Las hiperfenilalaninemias, alteraciones en el metabolismo de la fenilalanina, poseen heterogeneidad genética, clínica y bioquímica, con fenilalanina en plasma, mayor de 120 µmol/L (2 mg/dL. La benigna tiene valores entre 240 y 600 µmol/L (4 a 10 mg/dL con mayor actividad enzimática y no requiere tratamiento dietético. Se realizó una valoración clínica y de laboratorio a 32 niños con esta alteración al nacimiento entre 1989 y 1999, para conocer variaciones en las concentraciones séricas en el tiempo, presentación de algún síntoma o signo clínico de la enfermedad y el coeficiente de inteligencia de estos. Los 32 niños estudiados presentaron disminución de niveles del aminoácido, con respecto al nacimiento, entre 90 y 287 µmol/L (1, 5 mg/dL a 5, 52 mg/dL. La mayoría no mostró síntomas o signos clínicos de fenilcetonuria. El coeficiente de inteligencia promedio fue de 100,6 puntos. Se recomienda el estudio a todos los niños con esta alteración en Cuba y realizar estudios de mutaciones para demostrar la heterogeneidad alélica que explicara la expresividad variable en el fenotipo bioquímico y clínico en estos niños.Hyperphenylalaninemias, which are disorders in the metabolism of phenylalanine, show genetic, clinical and biochemical heterogeneity, with phenylalanine in plasma over 120 µmol/L (2 mg/dL. Benign hyperphenylalaninemia has values from 240 to 600 µmol/L (4 a 10 mg/dL with higher enzymatic activity and does not require diet therapy. A clinical and lab assessment of 32 children with this disorder at birth was made from 1989 to 1999 to find out the variations in time of serum concentrations, occurrence of some clinical symptom or sign of the disease and their intelligence quotient. The 32 studied children presented with reduction of aminoacid levels of 90 to 287 µmol/L (1, 5 mg/dL a 5, 52 mg/dL with respect to birth levels. The majority did not show clinical symptoms or signs of phenylketonuria. Average

Potenciales provocados auditivos en niños con riesgo neonatal de hipoacusia

Directory of Open Access Journals (Sweden)

Saúl Garza Morales

1997-02-01

Full Text Available Los potenciales provocados auditivos del tallo cerebral (PPATC son un método sencillo y no invasor de evaluación de la función auditiva, que se utiliza ampliamente en niños para detectar tempranamente hipoacusia. Entre abril de 1992 y mayo de 1994, se estudiaron 400 niños mexicanos que presentaban, al menos, un factor de riesgo neonatal de hipoacusia. La media de la edad de los niños estudiados fue 6,6 meses y la media de la edad gestacional al nacer, 35,1 semanas. El 51% de ellos fueron tratados con amikacina. Se registraron 1 427 factores de riesgo (3,5 por niño, entre los que predominaron la exposición a ototóxicos, la hiperbilirrubinemia y el peso al nacer menor de 1 500 g. En 27% se encontraron alteraciones auditivas de tipo periférico y en 13%, ausencia de respuesta a estímulos auditivos. El bajo peso y la menor edad gestacional al nacer, la concentración máxima de bilirrubina en el suero, la presencia de sepsis, la hemorragia subependimaria o intraventricular, la ventilación mecánica y la exposición a ototóxicos se asociaron significativamente con la presencia de hipoacusia grave o profunda.

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

Science.gov (United States)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-12-01

Ce3+-doped and Ce3+/Li+-codoped SrAlSi4N7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr3N2, AlN, α-Si3N4, CeN and Li3N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi4N7:Ce3+(Ce3+/Li+) were investigated in this work. The band structure calculated by the DMol3 code shows that SrAlSi4N7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce3+-doped SrAlSi4N7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi4N7 was identified as a major phase of the fired powders, and Sr5Al5Si21N35O2 and AlN as minor phases. Both Ce3+ and Ce3+/Li+ doped SrAlSi4N7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce3+/Li+-doped SrAlSi4N7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr0.97Al1.03Si3.997N\\94\\maccounttest14=t0005_18193 7:Ce3+0.03 with a commercial blue InGaN chip. It indicates that SrAlSi4N7:Ce3+ is a promising yellow emitting down-conversion phosphor for white LEDs.

Synthesis and charge storage properties of double-layered NiSi nanocrystals

International Nuclear Information System (INIS)

Yoon, Jong-Hwan

2010-01-01

Based on bidirectional diffusion of Ni atoms, double-layered nickel silicide (NiSi) nanocrystals (NCs) for multilevel charge storage were fabricated, and their charge storage properties were examined. The double layer was produced by long-term thermal annealing (for 4 h at 900 o C) of a sandwich structure comprised of a thin Ni film of 0.3 nm sandwiched between two silicon-rich oxide (SiO 1.36 ) layers. Transmission electron microscopic image clearly exhibits a distinct NiSi nanocrystal double layer with a gap of about 7 nm between the mean positions of particle distribution in each NC layer. Capacitance-voltage measurements on the metal/oxide/semiconductor (MOS) capacitors with the double-layered NiSi nanocrystals are shown to have the apparent two plateaus of charge storage, the large memory window of about 9 V and the improved charge retention stability.

Utilisation of mould temperature change in eliminating the Al5FeSi phases in secondary AlSi7Mg0.3 alloy

Directory of Open Access Journals (Sweden)

Bolibruchová D.

2017-03-01

Full Text Available This article describes the impact of the metal mould temperature change in eliminating the adverse effect of iron in the AlSi7Mg0.3 alloy. The kind of phases based on iron to be formed in aluminium alloys is determined by the alloy chemical composition, the melt overheating temperature prior to casting, and the cooling rate during crystallisation. In the experiment, we used three various mould temperatures, and their impact on the possible change in the adverse Al5FeSi phase, excreted in a needle form to a more compact form of Chinese writing or skeleton units. The experimental part did not use melt overheat that would result in impairment of the melt, for example due to increased gassing of the melt, as well as in a greater load on the smelting unit, thus resulting in increased energy expenditure. We can conclude from the obtained results that the mould temperature change does not have an adequate effect in eliminating the adverse effect of iron in Al-Si-Mg alloys.

Near-surface segregation in irradiated Ni3Si

International Nuclear Information System (INIS)

Wagner, W.; Rehn, L.E.; Wiedersich, H.

1982-01-01

The radiation-induced growth of Ni 3 Si films on the surfaces of Ni(Si) alloys containing = 3 Si phase has been observed. Post-irradiation depth profiling by Auger electron spectroscopy, as well as in situ analysis by high-resolution Rutherford backscattering spectrometry, reveals Si-enrichment at the surfaces of Ni(Si) alloys in excess of stoichiometric Ni 3 Si during irradiation. Thin, near-surface layers with silicon concentrations of 28 to 30 at.% are observed, and even higher Si enrichment is found in the first few atom layers. Transmission electron microscopy and selected area-electron diffraction were employed to characterize these Si-enriched layers. A complex, multiple-spot diffraction pattern is observed superposed on the diffraction pattern of ordered Ni 3 Si. The d-spacings obtained from the extra spots are consistent with those of the orthohexagonal intermetallic compound Ni 5 Si 2 . (author)

Terapia asistida con perros en niños con autismo revisión sistemática

OpenAIRE

Isaza Narváez, Ana Milena; Muñoz Chilito, Doumer Adrian

2013-01-01

Introducción: El autismo es un trastorno temprano y masivo del desarrollo en el cual se afecta la interacción social, el desarrollo del lenguaje, se presentan rituales y estereotipias. Hay evidencia que la interacción con un perro está asociada con efectos positivos en la salud del niño, lo cual se extiende al terreno terapéutico donde la compañía del perro estimula habilidades comunicativas para conectarse con el mundo exterior y romper el aislamiento que lo hace refractario a formas convenc...

Experiencias de calorimetría diferencial de barrido en aleaciones Al-Si

Directory of Open Access Journals (Sweden)

Carolina López-Eckerdt

2016-01-01

Full Text Available La observación de agujas características de una transformación displaciva en aleaciones U-Al-Si en el entorno del compuesto U3Si5 evidencia la necesidad de analizar las distintas transformaciones que ocurren durante el enfriamiento utilizando una técnica dinámica de identificación de transformaciones (calorimetría diferencial de barrido. Para evaluar la versatilidad de esta técnica, se estudiaron aleaciones Al-Si con concentraciones de Si entre 0,6% y 7,1% en peso. Se determinaron las temperaturas liquidus y eutéctica de cada aleación y se estimó la entalpía de formación de los precipitados de Si y de la reacción eutéctica. Los resultados reproducen las temperaturas de ambas reacciones según el diagrama de equilibrio del sistema binario Al-Si. Para el cálculo de las entalpías de transformación resulta indispensable obtener el porcentaje de fase transformada por otras técnicas de caracterización una vez finalizado el ensayo.

Effect of rapid solidification on the microstructure and mechanical properties of hot-pressed Al-20Si-5Fe alloys

International Nuclear Information System (INIS)

Rajabi, M.; Vahidi, M.; Simchi, A.; Davami, P.

2009-01-01

The aim of this work is to study the effect of cooling rate and subsequent hot consolidation on the microstructural features and mechanical strength of Al-20Si-5Fe-2X (X = Cu, Ni and Cr) alloys. Powder and ribbons were produced by gas atomization and melt spinning processes at two different cooling rates of 1 x 10 5 K/s and 5 x 10 7 K/s. The microstructure of the products was examined using optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The particles were consolidated by hot pressing at 400 deg. C/250 MPa/1 h under a high purity argon atmosphere and the microstructure, hardness and compressive strength of the compacts were evaluated. Results showed a profound effect of the cooling rate, consolidation stage, and transition metals on the microstructure and mechanical strength of Al-20Si-5Fe alloys. While microstructural refining was obtained at both cooling rates, the microstructure of the atomized powder exhibited the formation of fine primary silicon (∼ 1 μm), eutectic Al-Si phase with eutectic spacing of ∼ 300 nm, and δ-iron intermetallic. Supersaturated Al matrix containing 5-7 at.% silicon and nanometric Si precipitates (20-40 nm) were determined in the microstructure of the melt-spun ribbons. The hot consolidation resulted in coarsening of Si particles in the atomized particles, and precipitation of Si and Fe-containing intermetallics from the supersaturated Al matrix in the ribbons. The consolidated ribbons exhibited higher mechanical strength compared to the atomized powders, particularly at elevated temperatures. The positive influence of the transition metals on the thermal stability of the Al-20Si-5Fe alloy was noticed, particularly in the Ni-containing alloy.

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

International Nuclear Information System (INIS)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-01-01

Ce 3+ -doped and Ce 3+ /Li + -codoped SrAlSi 4 N 7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr 3 N 2 , AlN, α-Si 3 N 4 , CeN and Li 3 N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi 4 N 7 :Ce 3+ (Ce 3+ /Li + ) were investigated in this work. The band structure calculated by the DMol 3 code shows that SrAlSi 4 N 7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce 3+ -doped SrAlSi 4 N 7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi 4 N 7 was identified as a major phase of the fired powders, and Sr 5 Al 5 Si 21 N 35 O 2 and AlN as minor phases. Both Ce 3+ and Ce 3+ /Li + doped SrAlSi 4 N 7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce 3+ /Li + -doped SrAlSi 4 N 7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr 0.97 Al 1.03 Si 3.997 N/94/maccounttest14=t0005 1 8193 7 :Ce 3+ 0.03 with a commercial blue InGaN chip. It indicates that SrAlSi 4 N 7 :Ce 3+ is a promising yellow emitting down-conversion phosphor for white LEDs. - Graphical abstract: One-phosphor converted white light-emitting diode (LED) was fabricated by combining a blue LED chip and a yellow-emitting SrAlSi4N7:Ce 3+ phosphor (see inset), which has the color rendering index of 78 and color temperature of 6300 K. - Highlights: • We reported a new yellow nitride phosphor suitable for solid state lighting. • We solved the crystal structure and evidenced a disordered Si/Al distribution. • We fabricated a high color rendering white LEDs by using a single SrAlSi4N7:Ce

Propiedades mecánicas de materiales compuestos de matriz de aluminio reforzados con intermetálicos

Directory of Open Access Journals (Sweden)

Torres, B.

2001-04-01

Full Text Available In this work 2124 aluminium matrix composites reinforced with Ni₃Al, NiAl, MoSiO₂ and Cr₃Si intermetallic powder particles have been investigated. For comparision purposes, unreinforced 2124 and reinforced with SiC have also been studied. In all cases, the same powder metallurgy route was used, i.e. the 2124 alloy was obtained by rapid solidification and the intermetallic particles by self-propagating high-temperature synthesis (SHS. The matrix and the intermetallics were mechanically blended, cold compacted and finally hot extruded. Tensile tests were carried out in T1 and T4 treatments. Results indicate that mechanical properties depend strongly on the tendence to form new phases at the matrixintermetallic interface during procesing and/or futher thermal treatments. The materials which present better properties are those that present less reaction between matrix and intermetallic reinforcement, i.e. MoSiO₂ and SiC reinforced composites.

En este trabajo se estudia el comportamiento mecánico de varios materiales compuestos de matriz de aluminio 2124 reforzados con partículas de los intermetálicos, Ni₃Al, NiAl, MoSiO₂ y Cr₃Si. Los resultados obtenidos se comparan con la aleación 2124 monolítica y con esa misma aleación reforzada con partículas del cerámico SiC. En todos los casos, se sigue la misma ruta de procesado pulvimetalúrgico a partir de polvos rápidamente solidificados, en el caso de la aleación 2124, y de la molienda mecánica de un tocho obtenido por síntesis autopropagada a temperatura elevada (SHS, para el refuerzo intermetálico. Matriz y reforzante se mezclan, mecánicamente, para, a continuación, compactar uniaxialmente en frío, procediéndose, finalmente, a la consolidación por extrusión. Las propiedades mecánicas se estudian mediante ensayos de tracción en estado T1 y T4. Los resultados obtenidos indican que las propiedades mec

ac Conductivity of mixed spinel NiAl0.7Cr0.7Fe0.6O4

Indian Academy of Sciences (India)

Abstract. ac Conductivity measurements are carried out across the metal to insulator transition in NiAl0.7Cr0.7Fe0.6O4. The low frequency data is analyzed using Summerfield scaling theory for hopping conductivity. The exponent of the scaling behavior has significantly different values in the conducting and insulating ...

Nitrogen versus helium: effects of the choice of the atomizing gas on the structures of Fe50Ni30Si10B10 and Fe32Ni36Ta7Si8B17 powders

International Nuclear Information System (INIS)

Zambon, A.

2004-01-01

Gas atomization can produce, besides a possible significant degree of undercooling, high cooling rates, whose extent depends on the size of the droplets, on their velocity with respect to the surrounding medium, on the thermo-physical properties of both the alloy and the gas, and of course on the operating conditions such as melt overheating and gas-to-metal flow ratio. In this respect it is well-known that the atomizing gas can play a significant role in determining both the powder size distribution and the kind and mix of phases which result from the solidification and cooling processes. The microstructures and solidification morphologies of powders obtained from nitrogen and helium sonic gas atomization of two iron-nickel base glass forming alloys, Fe 50 Ni 30 Si 10 B 10 and Fe 32 Ni 36 Ta 7 Si 8 B 17 , were investigated by means of light microscopy, X-ray diffraction (XRD) and differential thermal analysis (DTA). The Fe 32 Ni 36 Ta 7 Si 8 B 17 alloy exhibits a higher proneness to the development of amorphous phase than the Fe 50 Ni 30 Si 10 B 10 alloy, while the effect of the higher speed attainable by the stream of helium with respect to that of nitrogen, affords not only to obtain a larger amount of particles in the finer size ranges, but also to affect the relative amounts of phases within the different size fractions

Educación y política en filosofía con niños y niñas. Reflexiones a partir de El maestro ignorante de Rancière

Directory of Open Access Journals (Sweden)

Julián Macías

2015-01-01

Full Text Available El presente trabajo gira en torno al objetivo, en cuanto a su politicidad, de la práctica de filosofía con niños y niñas. Por un lado, buscaremos poner de manifiesto las tensiones y paradojas que implica pensar la filosofía como una praxis educativa y política, y, por otro, ensayaremos una posible respuesta que permita tanto habitar esas tensiones y paradojas, como generar una transformación en las mismas prácticas educativas. Para ello, el trabajo será dividido en tres partes. Primero, el análisis de la propuesta Philosophy for Children de Lipman, enfatizando el concepto de comunidad de indagación y el rol que se le asigna al docente en dicho programa. En la segunda parte, bajo la hipótesis de que, si bien dicha propuesta se presenta a sí misma como innovadora, subyacen ciertos elementos que permitirían poner en cuestionamiento esa calificación, por lo que intentaremos mostrar las semejanzas con ciertos elementos de lo que podría denominarse “educación tradicional”. Por último, examinaremos algunos elementos del planteamiento ranceriano en el Maestro ignorante respecto a la relación docente-alumno. En la misma lógica de los apartados anteriores, analizaremos si efectivamente se plantea una propuesta diferente y hasta qué punto es posible pensar una diversa relación. 

Educación y política en filosofía con niños y niñas. Reflexiones a partir de El maestro ignorante de Rancière

Directory of Open Access Journals (Sweden)

Julián Macías

2015-01-01

Full Text Available El presente trabajo gira en torno al objetivo, en cuanto a su politicidad, de la práctica de filosofía con niños y niñas. Por un lado, buscaremos poner de manifiesto las tensiones y paradojas que implica pensar la filosofía como una praxis educativa y política, y, por otro, ensayaremos una posible respuesta que permita tanto habitar esas tensiones y paradojas, como generar una transfor - mación en las mismas prácticas educativas. Para ello, el trabajo será dividido en tres partes. Primero, el análisis de la propuesta Philosophy for Children de Lipman, enfatizando el concepto de comunidad de indagación y el rol que se le asigna al docente en dicho programa. En la segunda parte, bajo la hipótesis de que, si bien dicha propuesta se presenta a sí misma como innovadora, subyacen ciertos elementos que permitirían poner en cuestionamiento esa calificación, por lo que intentaremos mostrar las semejanzas con ciertos elementos de lo que podría denominarse “educación tradicional”. Por último, examinaremos algunos elementos del planteamiento ranceriano en el Maestro ignorante respecto a la relación docente-alumno. En la misma lógica de los apartados anteriores, analizaremos si efectivamente se plantea una propuesta diferente y hasta qué punto es posible pensar una diversa relación.

Magnetic order and crystal structure study of YNi{sub 4}Si-type NdNi{sub 4}Si

Energy Technology Data Exchange (ETDEWEB)

Yao, Jinlei [Research Center for Solid State Physics and Materials, School of Mathematics and Physics, Suzhou University of Science and Technology, Suzhou 215009 (China); Isnard, O. [Université Grenoble Alpes, Inst NEEL, BP166, Grenoble F-38042 (France); CNRS, Institut NEEL, 25 rue des martyrs, Grenoble F-38042 (France); Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, GSP-2, Moscow 119992 (Russian Federation); Ivanova, T.I. [Physics Department, Moscow State University, Moscow 119992 (Russian Federation); Koshkid' ko, Yu.S. [International Laboratory of High Magnetic Fields and Low Temperatures, Wrocław (Poland); VSB-Technical University of Ostrava, Ostrava-Poruba 70833 (Czech Republic); Bogdanov, A.E.; Nikitin, S.A. [Physics Department, Moscow State University, Moscow 119992 (Russian Federation); Suski, W. [International Laboratory of High Magnetic Fields and Low Temperatures, Wrocław (Poland); Polish Academy of Sciences, Trzebiatowski Institute of Low Temperatures and Structure Research, P.O. Box 1410, 50-950 Wrocław 2 (Poland)

2015-02-15

Magnetic measurements and neutron powder diffraction investigation of the magnetic structure of the orthorhombic YNi{sub 4}Si-type (space group Cmmm) NdNi{sub 4}Si compound are presented. The magnetocaloric effect of NdNi{sub 4}Si is calculated in terms of the isothermal magnetic entropy change and it reaches the maximum value of –3.3 J/kg K for a field change of 50 kOe near T{sub C}=12 K. Below ∼12 K, NdNi{sub 4}Si exhibits a commensurate b-axis collinear ferromagnetic ordering with the Cmm′m magnetic space group in a zero magnetic field. At 1.5 K, the neodymium atoms have the magnetic moment of 2.37(5) μ{sub B}. The orthorhombic crystal structure and its thermal evolution are discussed in comparison with the CaCu{sub 5}-type compound. - Graphical abstract: The NdNi{sub 4}Si supplement the series of the orthorhombic derivative of the CaCu{sub 5}-type, namely the YNi{sub 4}Si-type, RNi{sub 4}Si compounds (R=Y, La, Ce, Sm, Gd–Ho). Below ∼12 K in a zero applied magnetic field, NdNi{sub 4}Si exhibits a commensurate b-axis collinear ferromagnetic ordering with the Cmm′m magnetic space group. Compared to the CaCu{sub 5}-type NdNi{sub 4}Si compound, the YNi{sub 4}Si-type counterpart has the relatively high ferromagnetic ordering temperature (9.2 K vs. 12 K), the small magnetocaloric effect (–7.3 J/kg K vs. –3.3 J/kg K for ∆H=50 kOe), and the large magnetic anisotropy at low temperatures. In contrast with CaCu{sub 5}-type NdNi{sub 4}Si, YNi{sub 4}Si-type NdNi{sub 4}Si shows distinct hysteresis loop at 2 K.We suggest that orthorhombic distortion may be used as a prospective route for optimization of permanent magnetic properties in the family of CaCu{sub 5}-type rare earth materials. - Highlights: • Below ∼12 K the YNi{sub 4}Si-type NdNi{sub 4}Si shows a ferromagnetic ordering. • MCE of NdNi{sub 4}Si reaches value of –3.3 J/kg K in 0–50 kOe near Curie point. • NdNi{sub 4}Si exhibits b-axis ferromagnetic order with the Cmm′m magnetic space

Microstructure, Wear Resistance and Oxidation Behavior of Ni-Ti-Si Coatings Fabricated on Ti6Al4V by Laser Cladding.

Science.gov (United States)

Zhuang, Qiaoqiao; Zhang, Peilei; Li, Mingchuan; Yan, Hua; Yu, Zhishui; Lu, Qinghua

2017-10-30

The Ni-Ti-Si composite coatings were successfully fabricated on Ti6Al4V by laser cladding. The microstructure were studied by SEM (scanning electron microscopy) and EDS (energy dispersive spectrometer). It has been found that Ti₂Ni and Ti₅Si₃ phases exist in all coatings, and some samples have TiSi₂ phases. Moreover, due to the existence of these phases, coatings presented relatively higher microhardness than that of the substrate (826 HV (Vickers hardness)) and the microhardness value of coating 3 is about twice larger than that of the substrate. During the dry sliding friction and wear test, due to the distribution of the relatively ductile phase of Ti₂Ni and reinforcement phases of Ti₅Si₃ and TiSi₂, the coatings performed good wear resistance. The oxidation process contains two stages: the rapid oxidation and slow oxidation by high temperature oxidation test at 800 °C for 50 h. Meanwhile, the value of the oxidation weight gain of the substrate is approximately three times larger than that of the coating 4. During the oxidation process, the oxidation film formed on the coating is mainly consisted of TiO₂, Al₂O₃ and SiO₂. Phases Ti₂Ni, Ti₅Si₃, TiSi₂ and TiSi were still found and it could be responsible for the improvement in oxidation resistance of the coatings by laser cladding.

Magnetic order in Pu2M3Si5 (M = Co, Ni)

International Nuclear Information System (INIS)

Bauer, E D; Tobash, P H; Mitchell, J N; Kennison, J A; Ronning, F; Scott, B L; Thompson, J D

2011-01-01

The physical properties including magnetic susceptibility, specific heat, and electrical resistivity of two new plutonium compounds Pu 2 M 3 Si 5 (M = Co, Ni) are reported. Pu 2 Ni 3 Si 5 crystallizes in the orthorhombic U 2 Co 3 Si 5 structure type, which can be considered a variant of the BaAl 4 tetragonal structure, while Pu 2 Co 3 Si 5 adopts the closely related monoclinic Lu 2 Co 3 Si 5 type. Magnetic order is observed in both compounds, with Pu 2 Ni 3 Si 5 ordering ferromagnetically at T C = 65 K then undergoing a transition into an antiferromagnetic state below T N = 35 K. Two successive magnetic transitions are also observed at T mag1 = 38 K and T mag2 = 5 K in Pu 2 Co 3 Si 5 . Specific heat measurements reveal that these two materials have a moderately enhanced Sommerfeld coefficient γ ∼ 100 mJ/mol Pu K 2 in the magnetic state with comparable RKKY and Kondo energy scales.

Microestructura y propiedades mecánicas de materiales compuestos de matriz Al-Mg-Si-Cu reforzada con AlNp, procesados por extrusión de polvos

Directory of Open Access Journals (Sweden)

Ortiz, José Luis

2000-10-01

Full Text Available This article presents an experimental investigation on the structure and mechanical properties of an Al-Mg-Si-Cu P/M alloy reinforced with 5 %, 10 % and 15 % aluminum nitride, produced by extrusión of cold compacted powders mixtures. Mechanical properties in "as extruded" and T6 conditions are compared. Differential Scanning Calorimetry and Dilatometric analysis were conducted to gain further insight into the precipitation process of these materials. Low cost 6061Al/AlNp composites can be produced with rare and small porosity by extrusión of cold compacted shapes without canning. The mechanical properties of the MMCs obtained by this process have limitations for high particles fractions because of clustering effects. All materials are always harder than the matrix and shows a similar behavior during aging processes but kinetics is changed. Potential applications of dilatometric techniques in the aging investigations of aluminum alloys and aluminum matrix composites have been established.

Se presenta una investigación experimental sobre la relación entre la estructura y las propiedades mecánicas de materiales obtenidos mediante la extrusión en caliente de preformas de polvos compactados en frío y cuya matriz es una aleación Al-Mg-Si-Cu con composición cercana a la AA6061, reforzada con tres proporciones diferentes (5, 10 y 15 % en volumen de partículas de AlN. Se utilizó Calorimetría Diferencial de Barrido y Dilatometría sobre las muestras solubilizadas y templadas para complementar el estudio del efecto de las partículas sobre el envejecimiento de la aleación base. Se establece que es posible producir, a bajo costo, materiales compuestos de matriz metálica, MMCs, de matriz de aleación AA6061 reforzada con partículas de AlN con baja porosidad y buenas propiedades mecánicas, mediante la extrusión de mezclas de polvos compactados en frío, sin necesidad de enlatado. Sin embargo, las aglomeraciones de partículas, para

Acoso escolar como factor limitante en la inclusión educativa de niños, niñas y jóvenes con trastornos del espectro autista

Directory of Open Access Journals (Sweden)

Maribel Uribarrí Vázquez

2016-01-01

Full Text Available Esta investigación tuvo como propósito analizar el acoso escolar como factor limitante en la inclusión educativa de niños, niñas y jóvenes con Trastornos del Espectro Autista (TEA. La sustentación teórica se basó en la doctrina de Delgado,  Serrano, Olweusy,  Roldan,  entre otros. El tipo de investigación fue cualitativo con  método fenomenológico a través de entrevistas a profundidad y notas de campo. La  selección de informantes clave fue de7 estudiantes con TEA  asistentes a escuelas regulares. Se concluye que el acoso escolar genera en alumnos con TEA, sentimientos de inadecuación e inadaptación que conllevan al  aislamiento,    exclusión social, resistencia y deserción escolar.

Transmission electron microscopy characterization of laser-clad iron-based alloy on Al-Si alloy

International Nuclear Information System (INIS)

Mei, Z.; Wang, W.Y.; Wang, A.H.

2006-01-01

Microstructure characterization is important for controlling the quality of laser cladding. In the present work, a detailed microstructure characterization by transmission electron microscopy was carried out on the iron-based alloy laser-clad on Al-Si alloy and an unambiguous identification of phases in the coating was accomplished. It was found that there is austenite, Cr 7 C 3 and Cr 23 C 6 in the clad region; α-Al, NiAl 3 , Fe 2 Al 5 and FeAl 2 in the interface region; and α-Al and silicon in the heat-affected region. A brief discussion was given for their existence based on both kinetic and thermodynamic principles

Nanocatalytic growth of Si nanowires from Ni silicate coated SiC nanoparticles on Si solar cell.

Science.gov (United States)

Parida, Bhaskar; Choi, Jaeho; Ji, Hyung Yong; Park, Seungil; Lim, Gyoungho; Kim, Keunjoo

2013-09-01

We investigated the nanocatalytic growth of Si nanowires on the microtextured surface of crystalline Si solar cell. 3C-SiC nanoparticles have been used as the base for formation of Ni silicate layer in a catalytic reaction with the Si melt under H2 atmosphere at an annealing temperature of 1100 degrees C. The 10-nm thick Ni film was deposited after the SiC nanoparticles were coated on the microtextured surface of the Si solar cell by electron-beam evaporation. SiC nanoparticles form a eutectic alloy surface of Ni silicate and provide the base for Si supersaturation as well as the Ni-Si alloy layer on Si substrate surface. This bottom reaction mode for the solid-liquid-solid growth mechanism using a SiC nanoparticle base provides more stable growth of nanowires than the top reaction mode growth mechanism in the absence of SiC nanoparticles. Thermally excited Ni nanoparticle forms the eutectic alloy and provides collectively excited electrons at the alloy surface, which reduces the activation energy of the nanocatalytic reaction for formation of nanowires.

Optimization of Squeeze Parameters and Modification of AlSi7Mg Alloy

Directory of Open Access Journals (Sweden)

Zyska A.

2013-06-01

Full Text Available The paper present the examination results concerning mechanical properties of castings made of AlSi7MG alloy in correlation both with the most significant squeeze casting parameters and with the modification treatment. Experiments were planned and held according to the 23 factorial design. The regression equations describing the influence of the squeeze pressure, the mould temperature, and the quantity of strontium modifier on the strength and elongation of the examined alloy were obtained. It was found that the main factor controlling the strength increase is the squeeze pressure, while the plasticity (A5 of the alloy is affected most advantageously by modification. The application of modification treatment in squeeze casting technology enables for production of the slab-type castings made of AlSi7Mg alloy exhibiting strength at the level of 230 MPa and elongation exceeding 14%.

Corrosion Inhibition Study of Al-Cu-Ni Alloy in Simulated Sea-Water ...

African Journals Online (AJOL)

Akorede

ABSTRACT: A study on the inhibition of Al-Cu-Ni alloy in simulated ... which the percentage of Copper, and Nickel were kept .... proceed based on equation of reaction in eqn (4). Al .... Sodium-Modified A356.0-Type Al-Si-Mg Alloy in Simulated.

The Effect of Si Morphology on Machinability of Al-Si Alloys

Directory of Open Access Journals (Sweden)

Muhammet Uludağ

2015-12-01

Full Text Available Many of the cast parts require some sort of machining like milling, drilling to be used as a finished product. In order to improve the wear properties of Al alloys, Si is added. The solubility of Si in Al is quite low and it has a crystallite type structure. It behaves as particulate metal matrix composite which makes it an attractive element. Thus, the wear and machinability properties of these type of alloys depend on the morphology of Si in the matrix. In this work, Sr was added to alter the morphology of Si in Al-7Si and Al-12Si. Cylindrical shaped samples were cast and machinability characteristics of Sr addition was studied. The relationship between microstructure and machinability was evaluated.

Synthesis and microwave absorption enhancement of Fe-doped NiO@SiO2@graphene nanocomposites

International Nuclear Information System (INIS)

Wang, Lei; Huang, Ying; Ding, Xiao; Liu, Panbo; Zong, Meng; Wang, Yan

2013-01-01

Highlights: • Fe-doped NiO@SiO 2 @graphene composites have excellent microwave performance. • The reflection loss of Fe doped NiO@SiO 2 @graphene was below −10 dB in 7–11 GHz. • The maximum absorption of Fe-doped NiO@SiO 2 @graphene was −51.2 dB at 8.6 GHz. -- Abstract: Fe-doped NiO@SiO 2 @graphene nanocomposites have been successfully fabricated for the first time, in which Fe-doped NiO nanoparticles are about 3 nm in diameter. In order to measure their electromagnetic properties, Fe-doped NiO@SiO 2 @graphene (25 wt%) wax composites were then prepared. The experimental results show that Fe-doped NiO@SiO 2 @graphene nanocomposites exhibit significantly enhanced microwave absorption performance in terms of both the maximum reflection loss value and the absorption bandwidth in comparison with NiO@SiO 2 @graphene. The maximum reflection loss of Fe-doped NiO@SiO 2 @graphene nanocomposites can reach −51.2 dB at 8.6 GHz with a thickness of 4 mm, and the absorption bandwidth with the reflection loss below −10 dB is 4 GHz (from 7 to 11 GHz). Therefore, this kind of nanocomposites may have the potential as high-efficient absorbers for microwave absorption applications

Ni-Si oxide as an inducing crystallization source for making poly-Si

Energy Technology Data Exchange (ETDEWEB)

Meng, Zhiguo; Liu, Zhaojun; Li, Juan; Wu, Chunya; Xiong, Shaozhen [Institute of Photo-electronics, Nankai University, Tianjin (China); Zhao, Shuyun; Wong, Man; Kwok, Hoi Sing [Department of Electronic and Computer Engineering, Hong Kong University of Science and Technology, Kowloon, Hong Kong (China)

2010-04-15

Nickel silicon oxide mixture was sputtered on a-Si with Ni-Si alloy target with Ni:Si weight ratio of 1:9 and used as a new inducing source for metal induced lateral crystallization (MILC). The characteristics of the resulted poly-Si materials induced by Ni-Si oxide with different thickness were nearly the same. This means the metal induced crystallization with this new inducing source has wide processing tolerance to make MILC poly-Si. Besides, it reduced the residual Ni content in the resulted poly-Si film. The transfer characteristic curve of poly-Si TFT and a TFT-OLED display demo made with this kind of new inducing source were also presented in this paper. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Microstructural effects of phosphorus on pressure die cast Al-12Si components

Directory of Open Access Journals (Sweden)

Suárez-Peña, B.

2007-10-01

Full Text Available The refinement of cuboidal silicon in eutectic Al-Si alloys by phosphorus additions used to manufacture pressure die cast components was studied. The results show that the addition of phosphorus in the form of AlFeP mother alloy before process degassing, leads to the best refinement of the size of the Si-cuboids phase, among several phosphorus additions analysed in the present research.

Se ha estudiado el afino del silicio cuboidal en aleaciones eutécticas Al-Si por acción del fósforo, en piezas obtenidas mediante la técnica de fundición a presión. Tras la adición de fósforo en pruebas industriales, en las que dicho elemento se incorpora al baño con diversas composiciones, los mejores resultados se obtienen con la adición de la aleación madre AlFeP, previa al desgasificado industrial.

El efecto Mateo en niños con dificultades específicas de aprendizaje de las matemáticas

OpenAIRE

Blanco Pérez, Margarita; Bermejo Fernández, Vicente

2009-01-01

En el presente trabajo se intentó determinar si la presencia de Dificultades Específicas de Aprendizaje en Matemáticas (DAM) se asociaba con la caída de las puntuaciones en las pruebas psicométricas empleadas para valorar el Cociente Intelectual (CI) que con el paso de los cursos se observa en estos niños, tal como sostienen algunos autores con las Dificultades en Lectura y Matemáticas. Además, se evaluó si las diferencias en CI se relacionaban con rendimientos matemáticos igualmente diferen...

Efecto del V y el Si Sobre la Microestructura de Depósitos Realizados con Electrodos Tubulares Revestidos de Alto Contenido de Mn (Hadfield

Directory of Open Access Journals (Sweden)

Manuel Rodríguez

2017-10-01

Full Text Available Resumen: Las aleaciones para el relleno superficial Fe-Mn-C (Hadfield han demostrado una excelente resistencia al desgaste bajo altas cargas dinámicas. En los últimos años se han realizado numerosos estudios para aumentar la resistencia al desgaste y mejorar su desempeño, a través de la introducción de otros elementos de aleación. En el presente trabajo se investiga la microestructura y dureza de los depósitos de relleno con alto contenido de Mn y adiciones de 1.2% de V y 2.4% de Si. Los depósitos estudiados se realizaron utilizando electrodos tubulares revestidos fabricados a escala de laboratorio. Las fases y microconstituyentes en el metal depositado se identificaron mediante microscopía óptica (MO, electrónica de barrido (MEB, difracción de rayos X (DRX, dureza y microdureza. De acuerdo a los resultados obtenidos, la adición de V al sistema aleante originó que la fase predominante fuera la austenita. Además, contribuyó a la formación de carburos de vanadio (VC en la microestructura de la capa de relleno, sin observarse la presencia de carburos complejos. Por otra parte, la presencia de Si favoreció la formación de una red de ferrita interdendrítica. La adición de estos elementos de aleación mejoró las propiedades de estos depósitos, potencializando su uso en aplicaciones que requieren alta resistencia al desgaste bajo altas cargas.

Uso del Test de Rendimiento Continuo de Conners para diferenciar niños normales y con TDAH en Chile

OpenAIRE

Salas-Bravo, Sonia; Gonzalez-Arias, Mauricio; Araya-Piñones, Angelo; Valencia-Jimenez, Macarena; Oyarce-Cortes C., Sonia

2017-01-01

Resumen El trastorno de déficit atencional con hiperactividad (TDAH) constituye uno de los cuadros de mayor prevalencia durante la niñez. El presente trabajo se focalizó en evaluar si el Test de Rendimiento Continuo de Conners era capaz de discriminar entre niños con y sin TDAH diagnosticados por el docente. Se conformó una muestra no probabilística de 30 niños escolares (15 clínicos y 15 normales) a través de la aplicación del cuestionario de atención. Todos los niños completaron la aplicaci...

Magnetic and magnetocaloric properties of spin-glass material DyNi{sub 0.67}Si{sub 1.34}

Energy Technology Data Exchange (ETDEWEB)

Chen, X. [The Ames Laboratory, U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); College of Physics and Electronic Information Engineering, Neijiang Normal University, Neijiang 641100 (China); Mudryk, Y., E-mail: slavkomk@ameslab.gov [The Ames Laboratory, U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Pathak, A.K.; Feng, W. [The Ames Laboratory, U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Pecharsky, V.K. [The Ames Laboratory, U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States)

2017-08-15

Highlights: • Spin-glass state is observed in the DyNi{sub 0.67}Si{sub 1.4} compound. • Random Ni/Si distribution in the AlB{sub 2}-type structure leads to magnetic frustration. • Magnetic frustration affects magnetic field dependence of magnetocaloric effect. - Abstract: Structural, magnetic, and magnetocaloric properties of DyNi{sub 0.67}Si{sub 1.34} were investigated using X-ray powder diffraction, magnetic susceptibility, and magnetization measurements. X-ray powder diffraction pattern shows that DyNi{sub 0.67}Si{sub 1.34} crystallizes in the AlB{sub 2}-type hexagonal structure (space group: P6/mmm, No. 191, a = b = 3.9873(9) Å, and c = 3.9733(1) Å). The compound is a spin-glass with the freezing temperature T{sub G} = 6.2 K. The ac magnetic susceptibility measurements confirm magnetic frustration in DyNi{sub 0.67}Si{sub 1.34}. The maximum value of the magnetic entropy change determined from M(H) data is −16.1 J/kg K at 10.5 K for a field change of 70 kOe.

Preparation and electrochemical properties of La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 (x = 0, 0.30, 0.33, 0.36, 0.39) hydrogen storage alloys

International Nuclear Information System (INIS)

Tian, Xiao; Wei, Wei; Duan, Ruxia; Zheng, Xinyao; Zhang, Huaiwei; Tegus, O.; Li, Xingguo

2016-01-01

The as-cast alloy with the composition of La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 was prepared by vacuum arc melting. La–Mg–Ni-based La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 hydrogen storage alloy has been synthesized by high-energy vibratory milling blending of the La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 as-cast alloy and elemental Mg, followed by an isothermal annealing. The microstructures and electrochemical properties of the La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 and La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys were investigated by XRD, SEM and electrochemical measurements. The XRD analysis and Rietveld refinement showed that the as-cast La_0_._7_0Ni_2_._4_5Co_0_._7_5Al_0_._3_0 alloy consists of single LaNi_5 phase, whereas the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys contain the LaNi_5 and (La, Mg)_2Ni_7. The electrochemical measurements indicated that the maximum discharge capacity and discharge potential characteristic of the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys increases first and then decreases with increasing x. The maximum discharge capacity and discharge potential characteristic of alloy reaches the optimum when x is 0.36. The cyclic stability of the La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloy with a smaller quantity of Mg is better than that of the alloy with a larger quantity of Mg. - Highlights: • La–Mg–Ni-based alloy was synthesized by melting, milling and subsequent annealing. • Mg atoms exist in the La_2Ni_7 phase prior to LaNi_5 phase. • The La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloys consist of the LaNi_5 and (La, Mg)_2Ni_7. • The more Mg element the alloys contain, the easier aggregation Mg atom is. • The C_m_a_x of La_0_._7_0Mg_xNi_2_._4_5Co_0_._7_5Al_0_._3_0 alloy first increases and then decreases with rising x.

Density functional theory study of the interfacial properties of Ni/Ni3Si eutectic alloy

International Nuclear Information System (INIS)

Zhao, Yuhong; Wen, Zhiqin; Hou, Hua; Guo, Wei; Han, Peide

2014-01-01

In order to clarify the heterogeneous nucleation potential of α-Ni grains on Ni 3 Si particles in Ni-Ni 3 Si eutectic alloy, the work of adhesion (W ad ), fracture toughness (G), interfacial energy (γ i ), and electronic structure of the index (0 0 1), (1 1 0) and (1 1 1) Ni/Ni 3 Si interfaces with two different cohesive manners are investigated using first-principles method based on density functional theory. Results indicate that the center site stacking sequence (OM) is preferable to continue the natural stacking sequence of bulk Ni and Ni 3 Si. Since OM stacking interfaces have larger W ad , G and γ i than that of the top site stacking (OT) interfaces. The Ni/Ni 3 Si (1 1 0) interface with OM stacking has the best mechanical properties. Therefore, the formation of this interface can improve the stability, ductility and fracture toughness of Ni-Ni 3 Si eutectic alloy. The calculated interfacial energy of Ni/Ni 3 Si (0 0 1), (1 1 0) and (1 1 1) interfaces with OM stacking proves the excellent nucleation potency of Ni 3 Si particles for α-Ni phase from thermodynamic considerations. Besides, the electronic structure and chemical bonding of (1 1 0) interface with OM stacking are also discussed.

Microstructure and property of directionally solidified Ni-Si hypereutectic alloy

Science.gov (United States)

Cui, Chunjuan; Tian, Lulu; Zhang, Jun; Yu, Shengnan; Liu, Lin; Fu, Hengzhi

2016-03-01

This paper investigates the influence of the solidification rate on the microstructure, solid/liquid interface, and micro-hardness of the directionally solidified Ni-Si hypereutectic alloy. Microstructure of the Ni-Si hypereutectic alloy is refined with the increase of the solidification rate. The Ni-Si hypereutectic composite is mainly composed of α-Ni matrix, Ni-Ni3Si eutectic phase, and metastable Ni31Si12 phase. The solid/liquid interface always keeps planar interface no matter how high the solidification rate is increased. This is proved by the calculation in terms of M-S interface stability criterion. Moreover, the Ni-Si hypereutectic composites present higher micro-hardness as compared with that of the pure Ni3Si compound. This is caused by the formation of the metastable Ni31Si12 phase and NiSi phase during the directional solidification process.

The combined use of EBSD and EDX analyses for the identification of complex intermetallic phases in multicomponent Al-Si piston alloys

International Nuclear Information System (INIS)

Chen, C.-L.; Thomson, R.C.

2010-01-01

Multicomponent Al-Si based casting alloys are used for a variety of engineering applications, including for example, piston alloys. Properties include good castability, high strength, light weight, good wear resistance and low thermal expansion. In order for such alloys to continue operation to increasingly higher temperatures, alloy element modifications are continually being made to further enhance the properties. Improved mechanical and physical properties are strongly dependent upon the morphologies, type and distribution of the second phases, which are in turn a function of alloy composition and cooling rate. The presence of additional elements in the Al-Si alloy system allows many complex intermetallic phases to form, which make characterisation non-trivial. These include, for example, CuAl 2 , Al 3 Ni 2 , Al 7 Cu 4 Ni, Al 9 FeNi and Al 5 Cu 2 Mg 8 Si 6 phases, all of which may have some solubility for additional elements. Identification is often non-trivial due to the fact that some of the phases have either similar crystal structures or only subtle changes in their chemistries. A combination of electron backscatter diffraction (EBSD) and energy dispersive X-ray analysis (EDX) has therefore been used for the identification of the various phases. This paper will present comparisons of phase identification methodologies using EBSD alone, and in combination with chemical information, either directly or through post processing.

Low silicon U(Al,Si)3 stabilization by Zr addition

International Nuclear Information System (INIS)

Pizarro, L.M.; Alonso, P.R.; Rubiolo, G.H.

2009-01-01

Previous knowledge states that (U,Zr)Al 3 and U(Al,Si) 3 phases with Zr and Si content higher than 6 at.% (7.7 wt%) and 4 at.% (1.4 wt%), respectively, does not partially transform to UAl 4 at 600 o C. In this work, four alloys within the quaternary system U-Al-Si-Zr were made with a fixed nominal 0.18 at.% (0.1 wt%) Si content in order to assess the synergetic effect of both Zr and Si alloying elements to the thermodynamic stability of the (U,Zr)(Al,Si) 3 phase. Heat treatments at 600 deg. C were undertaken and samples were analyzed by means of XRD, EPMA and EDS techniques. A remarkable conclusion is that addition of 0.3 at.% Si in the (U,Zr)(Al,Si) 3 phase reduces in 2.7 at.% the necessary Zr content to inhibit its transformation to U(Al,Si) 4 .

El niño con discapacidad: elementos orientadores para su inclusión social

Directory of Open Access Journals (Sweden)

Eliana Isabel Parra Esquivel

2015-01-01

Full Text Available Objetivos: proporcionar orientaciones conceptuales y prácticas a cuidadores, maestros, profesionales que trabajen con población infantil y comunidad en general respecto a es - trategias inclusivas acertadas para el niño con discapacidad (cero a doce años. Para ello se mencionan algunas herramientas prácticas (procedimientos, instrumentos, estrategias, adecuaciones, cuya utilización ayuda a comprender la situación y a mejorar la participación del niño en contextos de desempeño ocupacional cotidiano: hogar, escuela, actividades de juego y de tiempo libre. En últimas, se espera favorecer una participación más efectiva del niño en sus ambientes y roles ocupacionales, al reconocer las demandas de estos, así como el manejo más acertado, desde la perspectiva profesional de Terapia Ocupacional. Materiales: metodológicamente, este estudio rastreó fuentes especializadas nacionales e internacionales de Terapia Ocupacional desde el año 2000 sobre tres conceptos clave: niños con discapacidad, desempeño ocupacional y estrategias inclusivas. En cada fuente se identificaron las estrategias de inclusión propuestas para favorecer la participación del niño en ocupaciones cotidianas. Conclusiones: se avanzó en plantear reflexiones sobre las implicaciones ocupacionales de la discapacidad en niños, en pro de favorecer dinámicas incluyentes. Los referentes conceptuales que explican la participación del niño en los ambientes y roles que le son cotidianos (hogar, escuela y disfrute de actividades lúdicas y de tiempo libre insisten en que las acciones con esta población deben partir de reconocer las particularidades en cada caso. Al sensibilizar sobre la complejidad de la discapacidad se asume una mirada multidi - mensional y transdisciplinaria en la comprensión, atención y valoración de las necesidades de los niños con discapacidad.

Susceptibilidad antimicrobiana de Streptococcus pneumoniae colonizante de nasofaringe en niños colombianos con neumonía

Directory of Open Access Journals (Sweden)

Aura Lucía Leal

1997-04-01

Full Text Available Streptococcus pneumoniae es uno de los principales agentes causales de infección respiratoria aguda (IRA en niños y su resistencia a antibióticos se ha incrementado en todo el mundo. En este estudio se determinaron los patrones de susceptibilidad a antimicrobianos de S. pneumoniae colonizante de las vías respiratorias altas en 272 niños hospitalizados por neumonía en dos hospitales de Santafé de Bogotá. Se aisló S. pneumoniae en 114 pacientes (42%. Se observó susceptibilidad disminuida a la penicilina en 19 aislamientos (17%, con sensibilidad intermedia en 12 (11% y franca resistencia en 7 (6%. Solo 1 de los 19 aislamientos resistentes a penicilina mostró también resistencia a la ceftriaxona. Se observó sensibilidad disminuida a la eritromicina en 3 aislamientos (3%, al cloranfenicol en 6 (5% y al cotrimoxazol (trimetoprima + sulfametoxazol en 46 (40%. Se encontró multirresistencia en 7 aislamientos (6%. El serotipo con sensibilidad disminuida a la penicilina que se halló con mayor frecuencia fue el 23F (68,4%. Se observó una asociación entre la edad, el uso previo de antibióticos y la colonización con S. pneumoniae con susceptibilidad disminuida a la penicilina o multirresistencia. Este estudio confirma la presencia de resistencia antimicrobiana de S. pneumoniae en Colombia y resalta la importancia del uso racional de los antibióticos y de la implementación de la vigilancia epidemiológica sobre este agente.

Theoretical analysis of compatibility of several reinforcement materials with NiAl and FeAl matrices

Science.gov (United States)

Misra, Ajay K.

1989-01-01

Several potential reinforcement materials were assessed for their chemical, coefficient of thermal expansion (CTE), and mechanical compatibility with the intermetallic matrices based on NiAl and FeAl. Among the ceramic reinforcement materials, Al2O3, TiC, and TiB2, appear to be the optimum choices for NiAl and FeAl matrices. However, the problem of CTE mismatch with the matrix needs to be solved for these three reinforcement materials. Beryllium-rich intermetallic compounds can be considered as potential reinforcement materials provided suitable reaction barrier coatings can be developed for these. Based on preliminary thermodynamic calculations, Sc2O3 and TiC appear to be suitable as reaction barrier coatings for the beryllides. Several reaction barrier coatings are also suggested for the currently available SiC fibers.

Atomistic calculations of hydrogen interactions with Ni3Al grain boundaries and Ni/Ni3Al interfaces

International Nuclear Information System (INIS)

Baskes, M.I.; Angelo, J.E.; Moody, N.R.

1995-01-01

Embedded Atom Method (EAM) potentials have been developed for the Ni/Al/H system. The potentials have been fit to numerous properties of this system. For example, these potentials represent the structural and elastic properties of bulk Ni, Al, Ni 3 Al, and NiAl quite well. In addition the potentials describe the solution and migration behavior of hydrogen in both nickel and aluminum. A number of calculations using these potentials have been performed. It is found that hydrogen strongly prefers sites in Ni 3 Al that are surrounded by 6 Ni atoms. Calculations of the trapping of hydrogen to a number of grain boundaries in Ni 3 Al have been performed as a function of hydrogen chemical potential at room temperature. The failure of these bicrystals under tensile stress has been examined and will be compared to the failure of pure Ni 3 Al boundaries. Boundaries containing a preponderance of nickel are severely weakened by hydrogen. In order to investigate the potential embrittlement of γ/γ' alloys, trapping of hydrogen to a spherical Ni 3 Al precipate in nickel as a function of chemical potential at room temperature has been calculated. It appears that the boundary is not a strong trap for hydrogen, hence embrittlement in these alloys is not primarily due to interactions of hydrogen with the γ/γ interface

CO impurities effect on LaNi4∙7Al0∙3 hydrogen storage alloy ...

Indian Academy of Sciences (India)

Administrator

LaNi4∙7Al0∙3 alloy was prepared by vacuum induction melting in high purity helium atmosphere, .... The particle size of the ... tated Ni, and hydrogen molecules are dissociated into .... range of 30–150 °C, the sample weight loss is about 1∙3%.

Electron microscopy characterization of Ni-Cr-B-Si-C laser deposited coatings.

Science.gov (United States)

Hemmati, I; Rao, J C; Ocelík, V; De Hosson, J Th M

2013-02-01

During laser deposition of Ni-Cr-B-Si-C alloys with high amounts of Cr and B, various microstructures and phases can be generated from the same chemical composition that results in heterogeneous properties in the clad layer. In this study, the microstructure and phase constitution of a high-alloy Ni-Cr-B-Si-C coating deposited by laser cladding were analyzed by a combination of several microscopy characterization techniques including scanning electron microscopy in secondary and backscatter imaging modes, energy dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). The combination of EDS and EBSD allowed unequivocal identification of micron-sized precipitates as polycrystalline orthorhombic CrB, single crystal tetragonal Cr5B3, and single crystal hexagonal Cr7C3. In addition, TEM characterization showed various equilibrium and metastable Ni-B, Ni-Si, and Ni-Si-B eutectic products in the alloy matrix. The findings of this study can be used to explain the phase formation reactions and to tune the microstructure of Ni-Cr-B-Si-C coatings to obtain the desired properties.

Microstructure and tribological properties of NiMo/Mo2Ni3Si intermetallic 'in-situ' composites

International Nuclear Information System (INIS)

Gui Yongliang; Song Chunyan; Yang Li; Qin Xiaoling

2011-01-01

Research highlights: → Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites was fabricated successfully with Mo-Ni-Si powder blends as the starting materials. Microstructure of the NiMo/Mo 2 Ni 3 Si composites consists of Mo 2 Ni 3 Si primary dendrites, binary intermetallic phase NiMo and small amount of Ni/NiMo eutectics structure. The NiMo/Mo 2 Ni 3 Si composites exhibited high hardness and outstanding tribological properties under room-temperature dry-sliding wear test conditions which were attributed to the covalent-dominant strong atomic bonds and excellent combination of strength and ductility and toughness. - Abstract: Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites with a microstructure of ternary metal silicide Mo 2 Ni 3 Si primary dendritic, the long strip-like NiMo intermetallic phase, and a small amount of Ni/NiMo eutectics structure were designed and fabricated using molybdenum, nickel and silicon elemental powders. Friction and wear properties of NiMo/Mo 2 Ni 3 Si composites were evaluated under different contact load at room-temperature dry-sliding wear test conditions. Microstructure, worn surface morphologies and subsurface microstructure were characterized by OM, XRD, SEM and EDS. Results indicate that NiMo/Mo 2 Ni 3 Si composites have low fiction coefficient, excellent wear resistance and sluggish wear-load dependence. The dominant wear mechanisms of NiMo/Mo 2 Ni 3 Si composites are soft abrasion and slightly superficial oxidative wear.

Corrosion behavior of Fe-Si metallic coatings added with NiCrAlY in an environment of fuel oil ashes at 700 C

Energy Technology Data Exchange (ETDEWEB)

Salinas-Bravo, V.M.; Porcayo-Calderon, J.; Romero-Castanon, T. [Instituto de Investigaciones Electricas, Gerencia de Procesos Termicos., Av. Reforma 113, C.P. 62490 Col. Palmira. Temixco. Morelos (Mexico); Dominguez-Patino, G.; Gonzalez-Rodriguez, J.G. [U.A.E.M. Centro de Investigaciones en Ingenieria y Ciencias Aplicadas., Av. Universidad 1001, C.P. 62210, Col. Chamilpa. Cuernavaca, Morelos (Mexico)

2005-07-01

Electrochemical potentiodynamic polarization curves and immersion tests for 300 h at 700 C in a furnace have been used to evaluate the corrosion resistance of Fe-Si metallic coatings added with up to 50 wt.% of NiCrAIY. The corrosive environment was fuel oil ashes from a steam generator. The composition of fuel oil ashes includes high content of vanadium, sodium and sulfur. The results obtained show that only the addition of 20 wt.% NiCrAlY to the Fe-Si coating improves its corrosion resistance. The behavior of all tested coatings is explained by the results obtained from the analysis of every coating using electron microscopy and energy dispersive X-ray analysis. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Compared production behavior of borax and unborax premixed SiC reinforcement Al7Si-Mg-TiB alloys composites with semi-solid stir casting method

Science.gov (United States)

Haryono, M. B.; Sulardjaka, Nugroho, Sri

2016-04-01

The present study was aimed to investigate the effect of borax additive on physical and mechanical properties of Al7Si-Mg-TiB with the reinforcement of silicon carbide. In this case, the different weight percentage from the reinforcement of SiC (10, 15, and 20% wt), and the borax additive (ratio 1:4) were homogenously added into the matrix by employing the semi-solid stir casting method at the temperature of 590°C. Al7Si-Mg-TiB melted in an electric resistance furnace at 800°C for 25 minutes and the holding time of 5 minutes; SiC was stirred with borax inside the chamber and heated at the temperature of 250°C for 25 minutes. Then, it melted by lowing the temperature into 590°C. The SiC-borax mixture was added into the electric resistance furnace, and automatically stirred by the stirrer at a constant speed (500 rpm for 3 minutes) in the composite A17Si-Mg-TiB. It melted when heated at 750°C for 17minutes,then, casting was performed on the prepared mould. The characterizations of Al7Si-Mg-TiB-SiC/borax were porosity, hardness, and microstructure on the Al7Si-Mg-TiB-SiC/ borax. The porosity of AMC tended to increase along with the increaseof the wt% SiC (1.4%-3.6%); however, borax additive underwent a decrease in porosity (0.14%-1.3%). Further, hardness tended to improve along with the increase of wt% SiC. The unboraxmixture had 79,6 HRB up to 94 HRB. Whereas, the borax additive mixture had 105,8 HRB up to 121 HRB.

Effects of Different Levels of Boron on Microstructure and Hardness of CoCrFeNiAlxCu0.7Si0.1By High-Entropy Alloy Coatings by Laser Cladding

Directory of Open Access Journals (Sweden)

Yizhu He

2017-01-01

Full Text Available High-entropy alloys (HEAs are novel solid solution strengthening metallic materials, some of which show attractive mechanical properties. This paper aims to reveal the effect of adding small atomic boron on the interstitial solid solution strengthening ability in the laser cladded CoCrFeNiAlxCu0.7Si0.1By (x = 0.3, x = 2.3, and 0.3 ≤ y ≤ 0.6 HEA coatings. The results show that laser rapid solidification effectively prevents brittle boride precipitation in the designed coatings. The main phase is a simple face-centered cubic (FCC matrix when the Al content is equal to 0.3. On the other hand, the matrix transforms to single bcc solid solution when x increases to 2.3. Increasing boron content improves the microhardness of the coatings, but leads to a high degree of segregation of Cr and Fe in the interdendritic microstructure. Furthermore, it is worth noting that CoCrFeNiAl0.3Cu0.7Si0.1B0.6 coatings with an FCC matrix and a modulated structure on the nanometer scale exhibit an ultrahigh hardness of 502 HV0.5.

Evolution of a novel Si-18Mn-16Ti-11P alloy in Al-Si melt and its influence on microstructure and properties of high-Si Al-Si alloy

Directory of Open Access Journals (Sweden)

Xiao-Lu Zhou

Full Text Available A novel Si-18Mn-16Ti-11P master alloy has been developed to refine primary Si to 14.7 ± 1.3 μm, distributed uniformly in Al-27Si alloy. Comparing with traditional Cu-14P and Al-3P, Si-18Mn-16Ti-11P provided a much better refining effect, with in-situ highly active AlP. The refined Al-27Si alloy exhibited a CTE of 16.25 × 10−6/K which is slightly higher than that of Sip/Al composites fabricated by spray deposition. The UTS and elongation of refined Al-27Si alloy were increased by 106% and 235% comparing with those of unrefined alloy. It indicates that the novel Si-18Mn-16Ti-11P alloy is more suitable for high-Si Al-Si alloys and may be a candidate for refining hypereutectic Al-Si alloy for electronic packaging applications. Moreover, studies showed that TiP is the only P-containing phase in Si-18Mn-16Ti-11P master alloy. A core-shell reaction model was established to reveal mechanism of the transformation of TiP to AlP in Al-Si melts. The transformation is a liquid-solid diffusion reaction driven by chemical potential difference and the reaction rate is controlled by diffusion. It means sufficient holding time is necessary for Si-18Mn-16Ti-11P master alloy to achieve better refining effect. Keywords: Hypereutectic Al-Si alloy, Primary Si, Refinement, AlP, Thermal expansion behavior, Si-18Mn-16Ti-11P master alloy

Gerichtete Erstarrung von Al-Si und Al-Si-Mn Legierungen unter dem Einfluss von magnetischen Wechselfeldern

OpenAIRE

Orth, Andreas

2013-01-01

In this work, samples of two alloys, Al-Si7 and Al-Si7-Mn1, are directionally solidified and their structure microscopically analysed. Thereby, the combined influence of induced current flow and intermetallic precipitates is of particular interest. A newly modified "Artemis" setup at the institute of material physics at the DLR in Cologne allows controlled solidification velocities of 30 to 240 micron/s under a constant temperature gradient of 3 K/mm. In using silica aerogels as part of the c...

Crystallization behavior and the thermal properties of Zr63Al7.5Cu17.5Ni10B2 bulk amorphous alloy

International Nuclear Information System (INIS)

Jang, J.S.C.; Chang, L.J.; Jiang, Y.T.; Wong, P.W.

2003-01-01

The ribbons of amorphous Zr 63 Al 7.5 Cu 17.5 Ni 10 B 2 alloys with 0.1 mm thickness were prepared by melt spinning method. The thermal properties and micro structural development during the annealing of amorphous alloy have been investigated by a combination of differential thermal analysis, differential scanning calorimetry, high-temperature optical microscope, X-ray diffractometry and TEM. The glass transition temperature for the Zr 63 Al 7.5 Cu 17.5 Ni 10 B 2 alloys are measured about 645 K (372 C). This alloy also obtains a large temperature interval ΔT x about 63 K. Meanwhile, the calculated T rg for Zr 63 Al 7.5 Cu 17.5 Ni 10 B 2 alloy presents the value of 0.57. The activation energy of crystallization for the alloy Zr 63 Al 7.5 Cu 17.5 Ni 10 B 2 was about 370± 10 kJ/mole as determined by the Kissinger and Avrami plot, respectively. These values are about 20% higher than the activation energy of crystallization for the Zr 65 Al 7.5 Cu 17.5 Ni 10 alloy (314 kJ/mol.). This implies that the boron additions exhibit the effect of improving the thermal stability for the Zr-based alloy. The average value of the Avrami exponent n were calculated to be 1.75±0.15 for Zr 63 Al 7.5 Cu 17.5 Ni 10 B 2 alloy. This indicates that this alloy presents a crystallization process with decreasing nucleation rate. (orig.)

Variaciones del perfil lipídico en pacientes pediátricos con desnutrición

Directory of Open Access Journals (Sweden)

Gerardo Fernando Fernández Soto

2017-06-01

Full Text Available La desnutrición infantil se registra como uno de los principales problemas de salud pública de América Latina; pues es una de las mayores causas de mortalidad y morbilidad evitable en los niños y niñas de Latinoamérica. Adicional al problema de la alta prevalencia de la desnutrición infantil, son motivo de gran preocupación las consecuencias que la desnutrición deja en los niños que la sufren; ya que los niños con desnutrición en los primeros años de vida tienen mayor riesgo de sufrir enfermedades crónicas en la vida adulta, tales como enfermedad cardiovascular, accidente cerebrovascular y diabetes mellitus 2, donde la ateroesclerosis es el evento etiopatológico que enlaza la desnutrición y la enfermedad crónica. Uno de los factores implicados en la etiología de la ateroesclerosis en los niños que han padecido desnutrición, es la alteración en el metabolismo de los lípidos, propia de la enfermedad y que se evidencia por la modificación en la distribución relativa de los lípidos plasmáticos. Las investigaciones actuales demuestran que niños con desnutrición aguda presentaban un aumento tanto de los triglicéridos como del colesterol de las lipoproteínas de muy baja densidad con disminución del colesterol de las lipoproteínas de alta densidad.

Effect of alloying elements on martensitic transformation in the binary NiAl(β) phase alloys

International Nuclear Information System (INIS)

Kainuma, R.; Ohtani, H.; Ishida, K.

1996-01-01

The characteristics of the B2(β) to L1 0 (β') martensitic transformation in NiAl base alloys containing a small amount of third elements have been investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM). It is found that in addition to the normal L1 0 (3R) martensite, the 7R martensite is also present in the ternary alloys containing Ti, Mo, Ag, Ta, or Zr. While the addition of third elements X (X: Ti, V, Cr, Mn, Fe, Zr, Nb, Mo, Ta, W, and Si) to the binary Ni 64 Al 36 alloy stabilizes the parent β phase, thereby lowering the M s temperature, addition of third elements such as Co, Cu, or Ag destabilizes the β phase, increasing the M s temperature. The occurrence of the 7R martensite structure is attributed to solid solution hardening arising from the difference in atomic size between Ni and Al and the third elements added. The variation in M s temperature with third element additions is primarily ascribed to the difference in lattice stabilities of the bcc and fcc phases of the alloying elements

Rechazo y victimización al alumnado con necesidad de apoyo educativo en primero de primaria

Directory of Open Access Journals (Sweden)

Mª Inés Monjas

2014-05-01

Full Text Available Este estudio pretende analizar el rechazo y victimización social que experimenta el alumnado con necesidad de apoyo educativo en comparación con sus compañeros. Participaron 1351 alumnos de primero de educación primaria de los que 253 (el 18.7% fueron etiquetados por sus profesores como alumnos con necesidad de apoyo educativo ya que presentaban dificultades que hicieron necesaria ayuda educativa especial y adicional al resto de compañeros. La información ha sido proporcionada por los iguales (tipología sociométrica, reputación social y calificación sociométrica, el profesorado (competencia social y el propio alumno (victimización y competencia percibida. Los resultados indican que los alumnos con necesidad de apoyo educativo son más rechazados, tienen peor reputación social (más agresivos, más aislados y menos prosociales y sus profesores les califican como menos competentes socialmente. Informan de que son victimizados con más frecuencia que sus compañeros y se autoperciben como menos competentes cognitivamente y menos aceptados por sus iguales. Todo ello revela una evidente caracterización de este alumnado como rechazado y excluido. Es más, los aspectos que definen el perfil del rechazo se ven intensificados cuando se trata de estos alumnos, motivos por los que se concluye con la necesidad de prestar especial atención y cuidado a este colectivo en riesgo.

Laser alloying of Al with mixed Ni, Ti and SiC powders

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-11-01

Full Text Available Laser alloying of aluminium AA1200 was performed with a 4.4kW Rofin Sinar Nd:YAG laser to improve the surface hardness. Alloying was carried out by depositing Ni, Ti and SiC powders of different weight ratios on the aluminium substrate. The aim...

Electrochemical corrosion behaviour of Mg-Al alloys with thermal spray Al/SiCp composite coatings; Comportamiento a la corrosion electroquimica de aleaciones MgAl con recubrimientos de materiales compuestos Al/SiCp mediante proyeccion termica

Energy Technology Data Exchange (ETDEWEB)

Pardo, A.; Feliu Jr, S.; Merino, M. C.; Mohedano, M.; Casajus, P.; Arrabal, R.

2010-07-01

The corrosion protection of Mg-Al alloys by flame thermal spraying of Al/SiCp composite coatings was evaluated by electrochemical impedance spectroscopy in 3.5 wt.% NaCl solution. The volume fraction of SiC particles (SiCp) varied between 5 and 30%. The as-sprayed Al/SiCp composite coatings revealed a high number of micro-channels, largely in the vicinity of the SiC particles, that facilitated the penetration of the electrolyte and the subsequent galvanic corrosion of the magnesium substrates. The application of a cold-pressing post-treatment reduced the degree of porosity of the coatings and improved the bonding at the coating/substrate and Al/SiC interfaces. This resulted in improved corrosion resistance of the coated specimens. The effectiveness of the coatings slightly decreased with the addition of 5-30 vol.% SiCp compared with the un reinforced thermal spray aluminium coatings. (Author) 31 refs.

PRECIPITATION HARDENING IN B2-ORDERED NiAl BY Ni2AlTiCOMPOUND

Institute of Scientific and Technical Information of China (English)

W.H. Tian; K. Ohishi; M. Nemoto

2001-01-01

Microstructural variations and correlated hardness changes in B2-ordered NiAl containing fine precipitation of Ni2AlTi have been investigated by means of transmission electron microscopy (TEM) and hardness tests. The amount of age hardening is not large as compared to the large microstructural variations during aging. TEM observations have revealed that the L21-type Ni2AlTi precipitates keep a lattice coherency with the NiAl matrix at the beginning of aging. By longer periods of aging Ni2AlTi precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. The temperature dependence of the yield strength of precipitate-containing B2-ordered NiAl was investigated by compression tests over the temperature range of 873-1273K. The fine precipitation of Ni2AlTi was found to enhance greatly the yield strength and the high-temperature strength is comparison with that of superalloy Mar-M200.``

Microstructure and mechanical properties of a single crystal NiAl alloy with Zr or Hf rich G-phase precipitates

Science.gov (United States)

Locci, I. E.; Noebe, R. D.; Bowman, R. R.; Miner, R. V.; Nathal, M. V.; Darolia, R.

1991-01-01

The possibility of producing NiAl reinforced with the G-phase (Ni16X6Si7), where X is Zr or Hf, has been investigated. The microstructure of these NiAl alloys have been characterized in the as-cast and annealed conditions. The G-phases are present as fine cuboidal precipitates (10 to 40 nm) and have lattice parameters almost four times that of NiAl. They are coherent with the matrix and fairly resistant to coarsening during annealing heat treatments. Segregation and nonuniform precipitate distribution observed in as-cast materials were eliminated by homogenization at temperatures near 1600 K. Slow cooling from these temperatures resulted in large plate shaped precipitates, denuded zones, and a loss of coherency in some of the large particles. Faster cooling produced a homogeneous fine distribution of cuboidal G-phase particles in the matrix. Preliminary mechanical properties for the Zr-doped alloy are presented and compared to binary single crystal NiAl. The presence of these precipitates appears to have an important strengthening effect at temperatures not less than 1000 K compared to binary NiAl single crystals.

Microstructure and mechanical properties of a single crystal NiAl alloy with Zr or Hf rich G-phase precipitates

International Nuclear Information System (INIS)

Locci, I.E.; Noebe, R.D.; Bowman, R.R.; Miner, R.V.; Nathal, M.V.

1991-01-01

In this paper the possibility of producing NiAl reinforced with the G-phase (Ni 16 X 6 Si 7 ), where X is Zr or Hf, has been investigated. The microstructures of these NiAl alloys have been characterized in the as-cast and annealed conditions. The G-phases are present as fine cuboidal precipitates (10 to 40 nm) and have lattice parameters almost four times that of NiAl. They are coherent with the matrix and fairly resistant to coarsening during annealing heat treatments. Segregation and non-uniform precipitate distribution observed in as-cast materials were eliminated by homogenization at temperatures near 1600 K. Slow cooling from these temperatures resulted in large plate shaped precipitates, denuded zones, and a loss of coherency in some of the large particles. Faster cooling produced a homogeneous fine distribution of cuboidal G-phase particles (≤10 nm) in the matrix. Preliminary mechanical properties for the Zr-doped alloy are presented and compared to binary single crystal NiAl. The presence of these precipitates appears to have an important strengthening effect at temperatures ≥1000 K compared to binary NiAl single crystals

Microdiffraction and CBED crystal structure determination of the Si-rich phase in laser-clad Ni alloy FP-5

International Nuclear Information System (INIS)

Liu, Y.; Mazumder, J.

1995-01-01

This paper demonstrates an example of using kinematical microdiffraction to solve an unknown Si-rich phase of micrometer size in a laser-clad Ni alloy FP-5 on Al alloy AA333. The composition of the Si-rich phase obtained by energy-dispersice X-ray spectroscopy (EDX) analysis in a transmission electron microscope is approximately 0.7wt%Al, 71wt%Si, 3.3wt%Cr, 0.8wt%Fe, 21wt%Ni and 2.8wt%Cu. The point group was identified by the standard convergent-beam symmetry analysis to be P6 3 /mmc (No. 194). Structure analysies by microdiffraction (MD) indicates that the Si-rich phase is a close-packed structure.The intensity distribution in the microdiffraction pattern of the [1120] zone axis taken with a very thin area showed a close match with kinematical calculation. A close-packed-structure model specified as ABCACB was deduced from the [1120] zone axis MD pattern. The randomly distributed atoms of all the elements in the unit cell are at 2/3, 1/3-1/12; 1/3, 1/12; 0, 0, 3/12, 1/3, 2/3, 5/12, 2/3, 1/3, 7/12; 0,0, 9/12. The model was checked by comparison with a simulated diffraction pattern map and with a simulated [0001] zone-axis CBED pattern, which showed complete agreement with the proposed model. (orig.)

Irradiation-induced precipitation in Ni--Si alloys

International Nuclear Information System (INIS)

Barbu, A.; Ardell, A.J.

1975-07-01

The microstructures of Ni + ion-irradiated Ni--Si solid-solution alloys, containing 2, 4, 6 and 8 at. percent Si were investigated as a function of dose, dose-rate, and temperature. Results of transmission electron microscopy and other data show the precipitation of γ' (Ni 3 Si) in all samples irradiated at 500 0 C. Characteristics of the precipitates are described and a mechanism for their formation is suggested. (U.S.)

Características de las crisis epilépticas en niños con insuficiencia renal crónica terminal.

Directory of Open Access Journals (Sweden)

Alan Luis Juárez Belaúnde

2008-01-01

Full Text Available Las crisis epilépticas son complicaciones frecuentes en niños que padecen de Insuficiencia Renal Crónica Terminal (IRC-T. Objetivo: Describir la frecuencia y características de las crisis epilépticas en niños con IRC-T. Material y Métodos: Estudio retrospectivo, tipo serie de casos. Se incluyeron 24 pacientes menores de 14 años de ambos sexos con IRC-T que presentaron al menos un episodio de crisis epiléptica, atendidos en el Hospital Nacional Cayetano Heredia entre enero de 1998 y marzo de 2006. Resultados: La frecuencia encontrada de crisis epiléptica en esta población fue de 24/188 (12,7%; 18/24 (75% se encontraban en tratamiento dialítico crónico al momento de presentarse la primera crisis epiléptica; las glomerulopatías fueron la etiología más frecuente de la IRC-T; la mayoría de niños (41,6% presentaron crisis parciales, y el hallazgo tomográfico más frecuente fue la hemorragia intraparenquimal. Conclusiones: La frecuencia de crisis epilépticas en esta serie de niños con IRC-T es menor que la descrita en la literatura revisada. (Rev Med Hered 2008;19:1-4.

Valence electronic structure of Ni in Ni Si alloys from relative K X-ray intensity studies

Science.gov (United States)

Kalayci, Y.; Aydinuraz, A.; Tugluoglu, B.; Mutlu, R. H.

2007-02-01

The Kβ-to-Kα X-ray intensity ratio of Ni in Ni 3Si, Ni 2Si and NiSi has been determined by energy dispersive X-ray fluorescence technique. It is found that the intensity ratio of Ni decreases from pure Ni to Ni 2Si and then increases from Ni 2Si to NiSi, in good agreement with the electronic structure calculations cited in the literature. We have also performed band structure calculations for pure Ni in various atomic configurations by means of linear muffin-tin orbital method and used this data with the normalized theoretical intensity ratios cited in the literature to estimate the 3d-occupation numbers of Ni in Ni-Si alloys. It is emphasized that investigation of alloying effect in terms of X-ray intensity ratios should be carried out for the stoichiometric alloys in order to make reliable and quantitative comparisons between theory and experiment in transition metal alloys.

Comportamiento a tracción a temperaturas ambiente y elevadas de nuevos composites basados en aleaciones hipereutécticas de Al-Si

Directory of Open Access Journals (Sweden)

Valer, J.

1997-02-01

Full Text Available This work shows the improvement obtained on tensile stress at room and high temperatures of hypereutectic Al-Si alloys. These alloys are produced by a combination of spray-forming, extrusión and thixoforming process, in comparison with conventional casting alloys. Al-25%Si-5%Cu, Al- 25%Si-5%Cu-2%Mg and Al-30%Si-5%Cu alloys have been studied relating their microstructural parameters with tensile stress obtained and comparing them with conventional Al-20%Si, Al-36%Si and Al-50%Si alloys. Al-25%Si-5%Cu alloy was tested before and after semi-solid forming, in order to distinguish the different behaviour of this alloy due to the different microstructure. The properties obtained with these alloys were also related to Al-SiC composites formed by similar processes.

En este trabajo se muestra la mejora obtenida en la resistencia a la tracción a temperatura ambiente y a elevadas temperaturas de aleaciones hipereutécticas de Al-Si producidas por una combinación de un proceso de solidificación rápida y del conformado en estado semisólido, en comparación con aleaciones obtenidas por procedimientos convencionales de inyección en estado líquido. Se han estudiado las aleaciones Al-25%Si-5%Cu, Al-25%Si-5%Cu-2%Mg y Al-30%Si-5%Cu, relacionando sus parámetros microestructurales con las resistencias a tracción obtenidas, y se han comparado con las aleaciones binarias Al-20%Si, Al-36%Si y Al-50%Si. La aleación Al-25%Si-5%Cu se ha ensayado antes y después del conformado en estado semisólido, lo que ha permitido conocer la diferencia en el comportamiento de la aleación como consecuencia de la distinta microestructura. También se comparan las propiedades obtenidas en estas aleaciones con las que presentan composites de aleaciones de aluminio reforzados con partículas de SiC y procesados por métodos similares.

Factores peri y postnatales relacionados con el asma bronquial en niños

Directory of Open Access Journals (Sweden)

Odalys Orraca Castillo

2014-06-01

Full Text Available Introducción: el asma es una de las enfermedades que recuerda a los médicos la importancia de los elementos clínicos y epidemiológicos en el reconocimiento del paciente. La enfermedad surge por factores genéticos y ambientales. Objetivo: describir los factores peri y postnatales del asma bronquial en pacientes de edad pediátrica en Pinar del Río. Material y método: se realizó un estudio descriptivo en la provincia Pinar del Río durante el periodo enero-junio 2010. Fueron seleccionados 585 asmáticos de edad pediátrica, por muestreo probabilístico estratificado, proporcional al universo de pacientes de las capitales municipales. Se consideró a cada municipio como estrato. Se usó la técnica de muestreo sistemático. Se calcularon las frecuencias absolutas y relativas de las variables cualitativas estudiadas. Resultados: el 10.8% de las madres fueron fumadoras durante el embarazo. El 6.7% y 39.5% de los niños fueron fumadores activos y pasivos respectivamente. El 34.2% de los niños asmáticos no mantuvo lactancia materna exclusiva hasta los tres meses. La rinitis ocupó el primer lugar (55% dentro de las co-morbilidades alérgicas. El 73.2% de los pacientes presentaron catarros, seguido de las amigdalitis e infecciones parasitarias. Conclusiones: el tabaquismo (pasivo y activo, la convivencia con animales domésticos, el consumo excesivo y temprano de leche de vaca con el retiro temprano de la lactancia materna exclusiva y las infecciones respiratorias como antecedentes patológicos personales constituyen factores peri y postnatales relacionados con niños asmáticos en Pinar del Río en quienes la rinitis y dermatitis se asociaron como parte de la marcha atópica.

Role of atomic bonding for compound and glass formation in Ni-Si, Pd-Si, and Ni-B systems

Science.gov (United States)

Tanaka, K.; Saito, T.; Suzuki, K.; Hasegawa, R.

1985-11-01

Valence electronic structures of crystalline compounds and glassy alloys of Ni silicides, Pd silicides, and Ni borides are studied by soft-x-ray spectroscopy over wide ranges of Si and B concentrations. The samples prepared include bulk compounds, glassy ribbons, and amorphous sputtered films. Silicon Kβ emissions of Ni and Pd silicides generally consist of a prominent peak fixed at ~=4.5 and ~=5.8 eV below the Fermi level EF, respectively, with a shoulder near EF which grows and shifts toward lower energy with increasing Si concentration. The former is identified as due to Si p-like states forming Si 3p-Ni 3d or Si 3p-Pd 4d bonding states while the latter as due to the corresponding antibonding states. Ni L3 and Pd L3 emissions of these silicides indicate that Ni 3d and Pd 4d states lie between the above two states. These local electronic configurations are consistent with partial-density-of-states (PDOS) calculations performed by Bisi and Calandra. Similar electronic configurations are suggested for Ni borides from B Kα and Ni L3 emissions. Differences of emission spectra between compounds and glasses of similar compositions are rather small, but some enhancement of the contribution of antibonding states to the PDOS near EF is suggested for certain glasses over that of the corresponding compounds. These features are discussed in connection with the compound stability and glass formability.

Hydrogen related peaks in Cu-LaNi4.7Al0.3

International Nuclear Information System (INIS)

Cuscueta, D.J.; Salva, H.R.; Ghilarducci, A.A.; Ruiz, F.C.

2009-01-01

In this work, the effect of Ni substitution by Cu in the LaNi 4.7 Al 0.3 hydride-forming alloy was studied in order to apply it to the negative electrodes of Ni-MH batteries. SEM, EDS and X-ray diffraction techniques were used to analyze the microstructure, composition and crystalline structure of the samples. A maximum electrochemical discharge capacity of 130 mAh/g was obtained. Internal friction (IF) and shear modulus (G) were measured by means of low frequency mechanical spectroscopy, between 100 and 450 K. In the electrochemical activated sample, two main IF peaks and typical relaxation steps in G showed up at 200 and 280 K. The first is ascribed to interactions between hydrides and H atoms in solid solution and dislocations, while the last one is attributed to the β ↔ α hydride phase transformation.

Niño con cardiopatía congénita controlada y muerte inesperada

Directory of Open Access Journals (Sweden)

Javier Horacio López Terrazas

2016-10-01

Full Text Available Niño de ocho meses de edad que llegó al Servicio de Urgencias del Instituto Nacional de Pediatría con cuadro de un día evolución con fiebre, odinofagia, vómitos y tres evacuaciones diarreicas abundantes. Falleció al día siguiente de su ingreso. Había ido al hospital donde se llevaba a cabo su manejo y en el que le administraron paracetamol, pero al día siguiente presentaba deshidratación, quejido respiratorio y saturaba 50% al aire ambiente, por lo que los padres administraron oxígeno por puntas nasales y acudieron a este Instituto.

Crecimiento y desarrollo de niños y jóvenes con diabetes mellitus tipo 1

Directory of Open Access Journals (Sweden)

Enrique Rotemberg Wilf

Full Text Available Resumen La diabetes mellitus es un síndrome metabólico que se caracteriza por hiperglucemia con alteración en el metabolismo de los carbohidratos, proteínas y grasas, causada por deficiencias en la producción o en la utilización de la insulina. Es la enfermedad endocrinometabólica más frecuente de la infancia y adolescencia. La diabetes tipo 1 es una condición crónica debido a la destrucción de las células beta de los islotes de Langerhans del páncreas por enfermedad autoinmune o sin causa conocida. El crecimiento y desarrollo general y cráneo facial del individuo van a estar influenciados por distintos factores que actúan interrelacionados. Los profesionales de la salud deben controlar la evolución del niño con diabetes 1 especialmente durante la pubertad. Es probable encontrar diferencias de crecimiento y desarrollo entre jóvenes con eficaz o con pobre control glucémico, en especial si la enfermedad es de inicio prepuberal y si es o no diagnosticada en forma precoz. La diabetes mellitus tipo 1 puede afectar la salud buco-dental de niños y adolescentes, con posibles consecuencias en la vida adulta

Effect of NaCl upon an Al-Si casting alloy hipoeutec; Efecto del NaCl sobre una aleacion de Al-Si hipoeutectica vaciada

Energy Technology Data Exchange (ETDEWEB)

Martinez Delgado, E.J.; Ortega de la Rosa, R. [Istituto Tecnologico de Zacatecas, Zacatecas (Mexico)]. E-mail: enriquemartinez_1999@yahoo.com; rubin_ortega_2002@yahoo.com.mx; Cisneros Guerrero, M.A. [Instituto Tecnologico de Saltillo, Saltillo, Coahuila (Mexico)]. E-mail: cisneros@its.mx; Haro Rodriguez, S. [Universidad Autonoma de Zacatecas, Zacatecas, Zacatecas (Mexico)]. E-mail: haros907@hotmail.com

2009-10-15

This work, comprehends the study about the effect of NaCl kind Halite upon the morphology of eutectic Silicon and porosity in a cast hipoeutectic Al-Si alloy. The melting was carried out in two furnaces, the first to combustion of LP gas in graphite crucible to increase the content of Si in the alloy from 0.13 to 5% wt using metallic silicon with a purity of 99.35% wt, and the second of electric resistances in the same kind of crucible to control the temperature at 750 degrees Celsius. The melting material was casting into molds of sand shell. To add the salt into the metallic bath, two techniques were used; one with injection by means of Argon gas and the other on by gravity, both cases three quantities of salt were used, 0.5, 1.5 and 2.5% wt respectively, powdered and preheated at 150 degrees Celsius during 60 min. The obtained samples were analyzed metallographily evidencing the modification of the eutectic Si, presenting the best results the samples with 1.5 and 2.5% wt of salt added by gravity. Too was obtained effect of Salt upon the degassing of bath metallic, where the simples with 1.5% wt presented the best results. Finally, by means of Scanning Electron Microscopy, the precipitates present were characterized in the samples. [Spanish] Este trabajo comprende el estudio del efecto del NaCl tipo Halita sobre la morfologia del Si eutectico y la porosidad en una aleacion fundida Al-Si hipoeutectica. La fusion se llevo a cabo en dos hornos, el primero a combustion con gas LP en crisol de grafito con la finalidad de incrementar el contenido de Si en la aleacion de 0.13 a 5% en peso, utilizando silicio metalico con una pureza de 99.35%, y el segundo de resistencias electricas en el mismo tipo de crisol para controlar la temperatura a 750 grados Celsios. El material fundido fue vaciado en modelos de arena. La sal se anadio al bano metalico a 0.5, 1.5 y 2.5% en peso, respectivamente, pulverizada y precalentada a 150 grados Celsios durante 60 min, mediante dos

Equiaxed and columnar dendrite growth simulation in Al-7Si- Mg ternary alloys using cellular automaton method

International Nuclear Information System (INIS)

Chen, Rui; Xu, Qingyan; Liu, Baicheng

2015-01-01

In this paper, a modified cellular automaton (MCA) model allowing for the prediction of dendrite growth of Al-Si-Mg ternary alloys in two and three dimensions is presented. The growth kinetic of S/L interface is calculated based on the solute equilibrium approach. In order to describe the dendrite growth with arbitrarily crystallographic orientations, this model introduces a modified decentered octahedron algorithm for neighborhood tracking to eliminate the effect of mesh dependency on dendrite growth. The thermody namic and kinetic data needed for dendrite growth is obtained through coupling with Pandat software package in combination with thermodynamic/kinetic/equilibrium phase diagram calculation databases. The effect of interactions between various alloying elements on solute diffusion coefficient is considered in the model. This model has first been used to simulate Al-7Si (weight percent) binary dendrite growth followed by a validation using theoretical predictions. For ternary alloy, Al-7Si-0.5Mg dendrite simulation has been carried out and the effects of solute interactions on diffusion matrix as well as the differences of Si and Mg in solute distribution have been analyzed. For actual application, this model has been applied to simulate the equiaxed dendrite growth with various crystallographic orientations of Al-7Si-0.36Mg ternary alloy, and the predicted secondary dendrite arm spacing (SDAS) shows a reasonable agreement with the experimental ones. Furthermore, the columnar dendrite growth in directional solidification has also been simulated and the predicted primary dendrite arm spacing (PDAS) is in good agreement with experiments. The simulated results effectively demonstrate the abilities of the model in prediction of dendritic microstructure of Al-Si-Mg ternary alloy. (paper)

Equiaxed and columnar dendrite growth simulation in Al-7Si- Mg ternary alloys using cellular automaton method

Science.gov (United States)

Chen, Rui; Xu, Qingyan; Liu, Baicheng

2015-06-01

In this paper, a modified cellular automaton (MCA) model allowing for the prediction of dendrite growth of Al-Si-Mg ternary alloys in two and three dimensions is presented. The growth kinetic of S/L interface is calculated based on the solute equilibrium approach. In order to describe the dendrite growth with arbitrarily crystallographic orientations, this model introduces a modified decentered octahedron algorithm for neighborhood tracking to eliminate the effect of mesh dependency on dendrite growth. The thermody namic and kinetic data needed for dendrite growth is obtained through coupling with Pandat software package in combination with thermodynamic/kinetic/equilibrium phase diagram calculation databases. The effect of interactions between various alloying elements on solute diffusion coefficient is considered in the model. This model has first been used to simulate Al-7Si (weight percent) binary dendrite growth followed by a validation using theoretical predictions. For ternary alloy, Al-7Si-0.5Mg dendrite simulation has been carried out and the effects of solute interactions on diffusion matrix as well as the differences of Si and Mg in solute distribution have been analyzed. For actual application, this model has been applied to simulate the equiaxed dendrite growth with various crystallographic orientations of Al-7Si-0.36Mg ternary alloy, and the predicted secondary dendrite arm spacing (SDAS) shows a reasonable agreement with the experimental ones. Furthermore, the columnar dendrite growth in directional solidification has also been simulated and the predicted primary dendrite arm spacing (PDAS) is in good agreement with experiments. The simulated results effectively demonstrate the abilities of the model in prediction of dendritic microstructure of Al-Si-Mg ternary alloy.

Forward Current Transport Mechanisms of Ni/Au—InAlN/AlN/GaN Schottky Diodes

Science.gov (United States)

Wang, Xiao-Feng; Shao, Zhen-Guang; Chen, Dun-Jun; Lu, Hai; Zhang, Rong; Zheng, You-Dou

2014-05-01

We fabricate two Ni/Au-In0.17Al0.83N/AlN/GaN Schottky diodes on substrates of sapphire and Si, respectively, and investigate their forward-bias current transport mechanisms by temperature-dependent current-voltage measurements. In the temperature range of 300-485 K, the Schottky barrier heights (SBHs) calculated by using the conventional thermionic-emission (TE) model are strongly positively dependent on temperature, which is in contrast to the negative-temperature-dependent characteristic of traditional semiconductor Schottky diodes. By fitting the forward-bias I-V characteristics using different current transport models, we find that the tunneling current model can describe generally the I-V behaviors in the entire measured range of temperature. Under the high forward bias, the traditional TE mechanism also gives a good fit to the measured I-V data, and the actual barrier heights calculated according to the fitting TE curve are 1.434 and 1.413 eV at 300K for InAlN/AlN/GaN Schottky diodes on Si and the sapphire substrate, respectively, and the barrier height shows a slightly negative temperature coefficient. In addition, a formula is given to estimate SBHs of Ni/Au—InAlN/AlN/GaN Schottky diodes taking the Fermi-level pinning effect into account.

High-Strength Ultra-Fine-Grained Hypereutectic Al-Si-Fe-X (X = Cr, Mn) Alloys Prepared by Short-Term Mechanical Alloying and Spark Plasma Sintering

Science.gov (United States)

Průša, Filip; Bláhová, Markéta; Vojtěch, Dalibor; Kučera, Vojtěch; Bernatiková, Adriana; Kubatík, Tomáš František; Michalcová, Alena

2016-01-01

In this work, Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn (wt %) alloys were prepared by a combination of short-term mechanical alloying and spark plasma sintering. The microstructure was composed of homogeneously dispersed intermetallic particles forming composite-like structures. X-ray diffraction analysis and TEM + EDS analysis determined that the α-Al along with α-Al15(Fe,Cr)3Si2 or α-Al15(Fe,Mn)3Si2 phases were present, with dimensions below 130 nm. The highest hardness of 380 ± 7 HV5 was observed for the Al-20Si-10Fe-6Mn alloy, exceeding the hardness of the reference as-cast Al-12Si-1Cu-1 Mg-1Ni alloy (121 ± 2 HV5) by nearly a factor of three. Both of the prepared alloys showed exceptional thermal stability with the hardness remaining almost the same even after 100 h of annealing at 400 °C. Additionally, the compressive strengths of the Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn alloys reached 869 MPa and 887 MPa, respectively, and had virtually the same values of 870 MPa and 865 MPa, respectively, even after 100 h of annealing. More importantly, the alloys showed an increase in ductility at 400 °C, reaching several tens of percent. Thus, both of the investigated alloys showed better mechanical properties, including superior hardness, compressive strength and thermal stability, as compared to the reference Al-10Si-1Cu-1Mg-1Ni alloy, which softened remarkably, reducing its hardness by almost 50% to 63 ± 8 HV5. PMID:28774094

Juegos en la estimulación a la psicomotricidad en niños y niñas con necesidades educativas especiales

Directory of Open Access Journals (Sweden)

Yanet Simón- Benzant

2017-11-01

Full Text Available Se presentan juegos que permiten la estimulación de la motricidad como elemento indispensable para el desarrollo del niño con necesidades educativas especiales, lo que permitirá favorecer el movimiento psicomotor con el fin de mejorar las capacidades intelectuales, afectivas y sociales permitiendo la adquisición de los nuevos aprendizajes, llevando al niño a la formación de las estructuras cognitivas de atención, memoria, percepción, lenguaje y a los niveles de pensamiento superiores que le irán permitiendo interpretar las nociones de espacialidad, temporalidad y velocidad, entre otras, al mismo tiempo que su movimiento se hace más autónomo, consciente a través de la expresión y el lenguaje.

Perfil neuropsicológico de niños con dislalias: alteraciones mnésicas y atencionales

Directory of Open Access Journals (Sweden)

Pablo Conde-Guzón

2014-10-01

Full Text Available En este estudio se pretende investigar el funcionamiento neuropsicológico de niños con dislalias. 34 niños con dislalia múltiple (distorsión o sustitución articulatoria de tres fonemas: /r/, /l/ y /s/ y exploración neurológica normal fueron comparados con 28 niños sin problemas del habla. El perfil neuropsicológico se estima mediante la Escala de Inteligencia Wechsler para Niños-Revisada (WISC-R y la Batería Neuropsicológica Luria-DNI. Los resultados indican que los niños dislálicos presentan: a un perfil mnésico globalmente deteriorado respecto al grupo de referencia aunque están preservado la memoria remota y la memoria de formas; b alteraciones en cinestesia y estereognosia; c problemas atencionales. Estos resultados indican que los niños dislálicos presentan problemas mnésicos y atencionales similares a los manifestados por niños con problemas de lenguaje secundarios a daño cerebral o afectaciones orgánicas o psicolingüísticas importantes. Debemos considerar este perfil neuropsicológico deteriorado en la orientación neurológica y psicoeducativa de estos niños.

Thermal stability and electrical characteristics of NiSi films with electroplated Ni(W) alloy

International Nuclear Information System (INIS)

Xin Yuhang; Hu Anmin; Li Ming; Mao Dali

2011-01-01

In this study, an electroplating method to deposited Ni, crystalline NiW(c-NiW), amorphous NiW (a-NiW) films on P-type Si(1 0 0) were used to form Ni-silicide (NiSi) films. After annealed at various temperatures, sheet resistance of Ni/Cu, c-NiW/Cu and a-NiW/Cu was measured to observe the performance of those diffusion barrier layers. With W added in the barrier layer, the barrier performance was improved. The results of XRD and resistance measurement of the stacked Si/Ni(W)/Cu films reveal that Cu atom could diffuse through Ni barrier layer at 450 deg. C, could diffuse through c-NiW at 550 deg. C, but could hardly diffuse through a-NiW barrier layer. c-NiW layer has a better barrier performance than Ni layer, meanwhile the resistance is lower than a-NiW layer.

Análisis mecánico y tribológico de los recubrimientos fe-cr-ni-c y ni-al-mo

Directory of Open Access Journals (Sweden)

JORGE E. MUÑOZ

2007-01-01

Full Text Available En este trabajo de investigación se evaluaron dos recubrimientos aplicados por medio de la técnica de rociado térmico por combustión, la aleación: Ni=89%, Al = 5,5%, Mo=5,5% y la aleación Fe=81,8%, Cr=16%, Ni=2%, C=0,2. La preparación superficial de las probetas se realizó usando chorro de arena. Se realizaron pruebas de resistencia al cortante, adherencia, desgaste abrasivo, desgaste por deslizamiento y flexión en cuatro puntos. El recubrimiento Fe-Cr-Ni-C presentó menor pérdida de masa, tanto para desgaste abrasivo como para el desgaste por deslizamiento. La multicapa presentó una mayor porosidad en el recubrimiento Ni-Al- Mo usado como capa base y la capa exterior de Fe-Cr-Ni-C presentó mayor cantidad de partículas no fundidas y óxidos. La falla ocurrida en el ensayo de adherencia para las probetas con recubrimiento multicapa fue de característica adhesiva y cohesiva. El esfuerzo en el que se presenta la fisura por flexión en el recubrimiento multicapa disminuyó con el aumento del espesor

A first-principles study of B2 NiAl alloyed with rare earth elements Pr, Pm, Sm, and Eu

Institute of Scientific and Technical Information of China (English)

He Jun-Qi; Wang You; Yan Mu-Fu; Pan Zhao-Yi; Guo Li-Xin

2013-01-01

The structural,elastic,and electronic properties of NiAl alloyed with rare earth elements Pr,Pm,Sm,and Eu are investigated by using density functional theory (DFT).The study suggests that Pr,Pm,Sm,and Eu all tend to be substituted for an Al site.Ni8Al7Pm possesses the largest ductility.Only the hardness and ductility of Ni8Al7Eu are enhanced simultaneously.The covalency strength of the Ni-Al bond in Ni8Al7Pm is higher than that in Ni8Al7Eu.The covalency strength of an Al-Al bond and that of a Ni-Ni bond in Ni8Al7Eu are higher than that in Ni8Al7Pm.The Ni-Pm bond and the Ni-Eu bond are covalent,and the covalency strength of the Ni-Pm bond is greater.The Al-Pm bond and the Al-Eu bond show great covalency strength and ionicity,respectively.

Sputtering Yields of Si and Ni from the Ni1-xSix System Studied by Rutherford Backscattering Spectrometry

Science.gov (United States)

Kim, Su Chol; Yamaguchi, Satoru; Kataoka, Yoshihide; Iwami, Motohiro; Hiraki, Akio; Satou, Mamoru; Fujimoto, Fuminori

1982-01-01

Sputtering yields of Si and Ni from thin layer films of Ni-Si compounds (Ni1-xSix), including the pure materials (Ni and Si), caused by 5 keV Ar+ ion bombardment were investigated using backscattering spectrometry. The sputtering yield for Si from Ni1-xSix increased with increasing Si concentration. However, there is an abrupt decrease in the yield for Si concentrations above NiSi2 to pure Si. This is in clear contrast to the sputtering yield of Ni from Ni1-xSix which increased with increasing Ni concentration monotonously. These results are discussed on the basis of both the difference in the atomic density and the electronic state of the alloy.

Terapias alternativas con animales para niños con necesidades especiales

OpenAIRE

Cea-Chueca, Aihnoa

2014-01-01

El presente trabajo de fin de grado consiste en la realización de un análisis y descripción de la literatura acerca de las distintas terapias animales, destinadas a niños con necesidades especiales: cómo y por qué surgieron, en qué consisten las terapias, cómo podemos utilizarlas, etc. Las terapias alternativas con animales se conocen como una alternativa terapéutica, donde se utiliza a un animal como co-terapeuta para poder desarrollar diferentes capacidades de los niños con necesidades espe...

Distribution of oxides in a Zr-Cu-Ni-Al-Nb-Si bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Heinrich, Jochen; Busch, Ralf [Chair of Metallic Materials, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany); Mueller, Frank; Huefner, Stefan [Chair of Experimental Physics, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany)

2010-07-01

The course of oxide presence with distance from the sample surface and bonding partner was studied for the bulk metallic glass with the nominal composition Zr{sub 57.9}Cu{sub 15.4}Ni{sub 12.7}Al{sub 10.2}Nb{sub 2.8}Si{sub 1} (at%) by X-ray photoelectron spectroscopy (XPS). Investigated specimens are taken from vacuum quench-cast rods subjected to oxidation at room temperature and atmosphere. Binding energies were determined in various depths using ion beam ablation of up to 100 nanometers. XPS spectra confirm oxidation primarily of the pure zirconium and aluminum constituents, all other peaks correspond to metallic bonds. While the surface area shows a passivating zirconia layer a few nanometers thick, oxygen is bonded predominantly with aluminum inside the bulk. Since the concentration of oxygen is a crucial factor in the crystallization behavior of bulk metallic glass forming liquids on basis of oxygen affine metals, so far only high purity materials were thought to be suitable. The findings in this study, however, are promising for alloys with industrial grade elements with sufficient glass forming ability. Comparisons of the alloy with differing oxygen content support the conclusion that aluminum acts as an appropriate scavenger for both adsorbed and large amounts of intrinsic oxygen in zirconium based amorphous metals.

Multiscale tomographic analysis of heterogeneous cast Al-Si-X alloys.

Science.gov (United States)

Asghar, Z; Requena, G; Sket, F

2015-07-01

The three-dimensional microstructure of cast AlSi12Ni and AlSi10Cu5Ni2 alloys is investigated by laboratory X-ray computed tomography, synchrotron X-ray computed microtomography, light optical tomography and synchrotron X-ray computed microtomography with submicrometre resolution. The results obtained with each technique are correlated with the size of the scanned volumes and resolved microstructural features. Laboratory X-ray computed tomography is sufficient to resolve highly absorbing aluminides but eutectic and primary Si remain unrevealed. Synchrotron X-ray computed microtomography at ID15/ESRF gives better spatial resolution and reveals primary Si in addition to aluminides. Synchrotron X-ray computed microtomography at ID19/ESRF reveals all the phases ≥ ∼1 μm in volumes about 80 times smaller than laboratory X-ray computed tomography. The volumes investigated by light optical tomography and submicrometre synchrotron X-ray computed microtomography are much smaller than laboratory X-ray computed tomography but both techniques provide local chemical information on the types of aluminides. The complementary techniques applied enable a full three-dimensional characterization of the microstructure of the alloys at length scales ranging over six orders of magnitude. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

Matriz de relación primaria en casos de niños y niñas con problemas de aprendizaje

Directory of Open Access Journals (Sweden)

Marta Isabel López

2010-10-01

Full Text Available La relación entre las dificultades de aprendizaje (DA y el contexto relacional primario de niño o niña que las presenta, es un aspecto importante reportado en la literatura y en la práctica clínica, y constituye un factor esencial en la comprensión del fenómeno de las DA. Nuestro objetivo en el estudio fue comprender la historia del desarrollo relacional de nueve niños y niñas con DA en la ciudad de Medellín, Colombia, para encontrar relaciones de sentido entre dicha historia y sus DA. La metodología utilizada fue cualitativa desde el enfoque hermenéutico-fenomenológico. Encontramos una dinámica de relación primaria caracterizada por ansiedad y apoyo constante al niño o niña por parte de la madre, y por un padre por fuera de la relación madre - niño o niña. Esa dinámica se reproduce en las relaciones con otras personas y situaciones, favoreciendo la emergencia de un niño o niña en un lugar de discapacidad.

Matriz de relación primaria en casos de niños y niñas con problemas de aprendizaje

Directory of Open Access Journals (Sweden)

Marta Isabel López

2010-01-01

Full Text Available La relación entre las dificultades de aprendizaje (DA y el contexto relacional primario del niño o niña que las presenta, es un aspecto importante reportado en la literatura y en la práctica clínica, y constituye un factor esencial en la comprensión del fenómeno de las DA. Nuestro objetivo en el estudio fue comprender la historia del desarrollo relacional de nueve niños y niñas con DA en la ciudad de Medellín, Colombia, para encontrar relaciones de sentido entre dicha historia y sus DA. La metodología utilizada fue cualitativa desde el enfoque hermenéutico-fenomenológico. Encontramos una dinámica de relación primaria caracterizada por ansiedad y apoyo constante al niño o niña por parte de la madre, y por un padre por fuera de la relación madre - niño o niña. Esa dinámica se reproduce en las relaciones con otras personas y situaciones, favoreciendo la emergencia de un niño o niña en un lugar de discapacidad.

Production of 26Al by spallation of Fe, Si, Al nuclei

International Nuclear Information System (INIS)

Paillard, P.

1977-01-01

Cross sections for 7 Be, 10 Be and 26 Al formation in Al, Si and Fe targets bombarded with 0.6 and 24GeV protons have been measured by using highly selective chemical separation and low level background counters. Results for 26 Al at 0.6GeV are in mb: 17.9 + or - 2.7 in Al, 12.5 + or - 2.5 in Si and 0.45 + or - 0.14 in Fe; at 24GeV 2.6 + or - 0.5mb in Fe. Results for 10 Be are not valid on account of experimental difficulties. It is deduced from these values of aluminium in cosmic ray propagation that 26 Al is not yet cosmic ray chronometer [fr

Crystal growth velocity in deeply undercooled Ni-Si alloys

Science.gov (United States)

Lü, Y. J.

2012-02-01

The crystal growth velocity of Ni95Si5 and Ni90Si10 alloys as a function of undercooling is investigated using molecular dynamics simulations. The modified imbedded atom method potential yields the equilibrium liquidus temperatures T L ≈ 1505 and 1387 K for Ni95Si5 and Ni90Si10 alloys, respectively. From the liquidus temperatures down to the deeply undercooled region, the crystal growth velocities of both the alloys rise to the maximum with increasing undercooling and then drop slowly, whereas the athermal growth process presented in elemental Ni is not observed in Ni-Si alloys. Instead, the undercooling dependence of the growth velocity can be well-described by the diffusion-limited model, furthermore, the activation energy associated with the diffusion from melt to interface increases as the concentration increases from 5 to 10 at.% Si, resulting in the remarkable decrease of growth velocity.

Athermal metal optics made of nickel plated AlSi40

Science.gov (United States)

Gebhardt, Andreas; Kinast, Jan; Rohloff, Ralf-Rainer; Seifert, Walter; Beier, Matthias; Scheiding, Sebastian; Peschel, Thomas

2017-11-01

Metal optics is an inherent part of space instrumentation for years. Diamond turned aluminum (Al6061) mirrors are widely used for application in the mid- and near-infrared (mid-IR and NIR, respectively) spectral range. Aluminum mirrors plated with electroless nickel (NiP) expand the field of application towards multispectral operating instruments down to the ultraviolet wavelengths. Due to the significant mismatch in the coefficient of thermal expansion (CTE) between aluminum and NiP, however, this advantage occurs at the cost of bimetallic bending. Challenging requirements can be met by using bare beryllium or aluminum beryllium composites (AlBeMet) as a CTE tailored substrate material and amorphous NiP as polishable layer. For health reasons, the use of beryllium causes complications in the process chain. Thus, the beryllium approach is subjected to specific applications only. Metal optics has proven to be advantageous in respect of using conventional CNC and ultra-precision fabrication methods to realize complex and light-weighted instrument structures. Moreover, the mirror designs can be effectively optimized for a deterministic system assembly and optimization. Limitations in terms of dimensional stability over temperature and time are mainly given by the inherent material properties (figures of merit) of the substrate material in interaction with the polishing layer. To find an optimal compromise, a thermal matched aluminum-silicon alloy (silicon contents ≍ 40 wt%) plated with NiP (AlSi40/NiP ) was investigated in a joined project of the Max Planck Institute for Astronomy MPIA and the Fraunhofer Institute for Applied Optics and Precision Engineering IOF. The main tasks of the project were the minimization of the bimetallic bending, the development of reliable stabilizing and aging procedures, and the establishment of a proven fabrication method. This paper describes fundamental results regarding the optimization of the athermal material combination

Alimentación de niños con diabetes mellitus tipo 1 con respecto a las recomendaciones

OpenAIRE

San Martín Jiménez, Rocío

2014-01-01

Introducción: La diabetes tipo 1 es una enfermedad crónica prevalente en la infancia, siendo unos de los pilares fundamentales de su tratamiento la alimentación. Diseñamos un estudio para valorar el grado de cumplimiento de las recomendaciones nutricionales de los pacientes pediátricos con diabetes tipo 1. Diseño y métodos. Estudio observacional transversal de 50 niños y adolescentes con diabetes tipo 1, que acuden al Hospital Clínico Universitario de Valladolid. La ingesta fue recogida me...

Effect of Si on DC arc plasma generation from Al-Cr and Al-Cr-Si cathodes used in oxygen

Science.gov (United States)

Zhirkov, I.; Landälv, L.; Göthelid, E.; Ahlgren, M.; Eklund, P.; Rosen, J.

2017-02-01

Al2O3 alloyed with Cr is an important material for the tooling industry. It can be synthesized from an arc discharge using Al-Cr cathodes in an oxygen atmosphere. Due to formation of Al-rich oxide islands on the cathode surface, the arc process stability is highly sensitive to oxygen pressure. For improved stability, the use of Al0.70Cr0.25Si0.05 cathodes has previously been suggested, where Si may reduce island formation. Here, we have investigated the effect of Si by comparing plasma generation and thin film deposition from Al0.7Cr0.3 and Al0.7Cr0.25Si0.05 cathodes. Plasma ion composition, ion energies, ion charge states, neutral species, droplet formation, and film composition have been characterized at different O2 flow rates for arc currents of 60 and 90 A. Si and related compounds are detected in plasma ions and in plasma neutrals. Scanning electron microscopy and energy dispersive X-ray analysis show that the cathode composition and the film composition are the same, with Si present in droplets as well. The effect of Si on the process stability, ion energies, and ion charge states is found to be negligible compared to that of the arc current. The latter is identified as the most relevant parameter for tuning the properties of the reactive discharge. The present work increases the fundamental understanding of plasma generation in a reactive atmosphere, and provides input for the choice of cathode composition and process parameters in reactive DC arc synthesis.

The crystallization of (NiCu)ZrTiAlSi glass/crystalline composite

International Nuclear Information System (INIS)

Czeppe, T.; Sypien, A.; Ochin, P.; Anastassova, S.

2007-01-01

Alloys of composition (Ni 1-x Cu x ) 60 Zr 18 Ti 13 A1 5 Si 4 were investigated in the form of ribbons and massive samples. The microstructure of the massive samples consists of dendritic crystals in the amorphous or nanocrystalline matrix. The amount of the amorphous phase is the lowest in the sample with the highest Cu content. The segregation in the liquid phase, leading to the local differences in density and the composition of the crystallizing dendrites in the samples crystallized in the copper mould was shown. The typical compositions of the multi-component crystals could be distinguished; one with the increased content of aluminum, the second with the high content of silicon and third, with the high content of (NiCu) and (ZrTi). The cubic phase Ni(Cu)Ti(Zr) with Cu and Zr dissolved could be identified. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Influence of Ultrasonic Melt Treatment and Cooling Rates on the Microstructural Development and Elevated Temperature Mechanical Properties of a Hypereutectic Al-18Si-4Cu-3Ni Piston Alloy

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jea-Hee; Cho, Young-Hee; Jung, Jae-Gil; Lee, Jung-Moo [Korea Institute of Materials Science (KIMS), Changwon (Korea, Republic of); Park, Ik Min [Pusan National University, Busan (Korea, Republic of)

2017-06-15

The influence of ultrasonic melt treatment (UST) combined with a change in cooling rates on the microstructure and elevated temperature mechanical properties of a hypereutectic Al-18Si-4Cu-3Ni piston alloy was investigated. Microstructural observation confirmed that UST effectively refined the sizes of primary Si and intermetallic compounds (e.g. ε-Al{sub 3}Ni) while promoting their homogeneous distribution. Besides the refinement of the constituent phases, the size of the dendrite arm spacing (DAS), which was hardly affected by UST, significantly deceased with increasing cooling rates. The refinement of the solidification structure in the alloy achieved through both UST and increased cooling rates resulted in an improvement in tensile properties, ultimate tensile strength and elongation in particular, after T5 heat treatment followed by overaging at 350 ℃. However, the elevated temperature yield strength of the alloy was not associated with the refinement, but was rather correlated with the 3-D interconnectivity, morphology and volume fraction of the primary Si.

Effect of Annealing Time for Quenching CuAl7Fe5Ni5W2Si2 Bronze on the Microstructure and Mechanical Properties

Directory of Open Access Journals (Sweden)

B. P. Pisarek

2012-04-01

Full Text Available This paper presents the influence of annealing time 30, 60 and 120 min at 1000°C for quenching CuAl7Fe5Ni5W2Si2 bronze in 10% water solution of NaCl, on the microstructure and mechanical properties. The presented results concern the species newly developed aluminum-iron-nickel bronze, with additions W and Si.In order to determine changes in the microstructure of the hardened bronze metallographic studies were performed on cylindrical samples of diameter 10 mm, on the metallographic microscope with digital image analysis, X-ray phase analysis, EDX point with the digital recording on the computer. Specified percentage of the microstructure of martensite and bainite, participation of proeutectoid α phase in the microstructure, grain size of former β phase, the amount of dissolved κ phase.It was found that in the microstructure of bronze in the cast state, there are a number of intermetallic phases of κ type. At interphase boundaries of primary intermetallic faceted precipitates, especially rich in tungsten (IM_W, nucleate and grow dendritic primary intermetallic κI phases, with chemical composition similar to the type of Fe3Si iron silicide.Dissolved, during the heating, in the β phase are all the intermediate phase included in the microstructure, with the exception of primary intermetallic phases of tungsten and κI. Prolongation of the isothermal annealing causes coagulation and coalescence of primary phases. In microstructure of the bronze after quenching obtained the α phase precipitation on the grain boundary of secondary β phase, coarse bainite and martensite, for all annealing times. With the change of annealing time are changed the relative proportions of individual phases or their systems, in the microstructure. In the microstructure of bronze, hold at temperature of 1000°C for 60 min, after quenching martensitic microstructure was obtained with the primary phases, and the least amount of bainite.

Electrochemical properties of rapidly solidified Si-Ti-Ni(-Cu) base anode for Li-ion rechargeable batteries

Science.gov (United States)

Kwon, Hye Jin; Sohn, Keun Yong; Park, Won-Wook

2013-11-01

In this study, rapidly solidified Si-Ti-Ni-Cu alloys have been investigated as high capacity anodes for Li-ion secondary batteries. To obtain nano-sized Si particles dispersed in the inactive matrix, the alloy ribbons were fabricated using the melt spinning process. The thin ribbons were pulverized using ball-milling to make a fine powder of ˜ 4 µm average size. Coin-cell assembly was carried out under an argon gas in a glove box, in which pure lithium was used as a counter-electrode. The cells were cycled using the galvanostatic method in the potential range of 0.01 V and 1.5 V vs. Li/Li+. The microstructure and morphology were examined using an x-ray diffractometer, Field-Emission Scanning Electron Microscopy and High Resolution Transmission Electron Microscopy. Among the anode alloys, the Si70Ti15Ni15 electrodes had the highest discharge capacity (974.1 mAh/g) after the 50th cycle, and the Si60Ti16Ni16Cu8 electrode showed the best coulombic efficiency of ˜95.9% in cyclic behavior. It was revealed that the Si7Ni4Ti4 crystal phase coexisting with an amorphous phase, could more efficiently act as a buffer layer than the fully crystallized Si7Ni4Ti4 phase. Consequently, the electrochemical properties of the anode materials pronouncedly improved when the nano-sized primary Si particle was dispersed in the inactive Si7Ni4Ti4-based matrix mixed with an amorphous structure.

Formation of AlFeSi phase in AlSi12 alloy with Ce addition

Directory of Open Access Journals (Sweden)

S. Kores

2012-04-01

Full Text Available The influence of cerium addition on the solidification sequence and microstructure constituents of the Al-Si alloys with 12,6 mass % Si was examined. The solidification was analyzed by a simple thermal analysis. The microstructures were examined with conventional light and scanning electron microscopy. Ternary AlSiCe phase was formed in the Al-Si alloys with added cerium during the solidification process. AlSiCe and β-AlFeSi phases solidified together in the region that solidified the last. Cerium addition influenced on the morphology of the α-AlFeSi phase solidification.

Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach

Directory of Open Access Journals (Sweden)

Dongmei Li

2017-08-01

Full Text Available Cu-Ni-Si alloys are widely used due to their good electrical conductivities in combination with high strength and hardness. In the present work, minor-alloying with M = (Cr, Fe, Mo, Zr was conducted for the objective of further improving their hardness while maintaining their conductivity level. A cluster-plus-glue-atom model was introduced to design the compositions of M-alloyed Cu-Ni-Si alloys, in which an ideal composition formula [(Ni,Si,M-Cu12]Cu3 (molar proportion was proposed. To guarantee the complete precipitation of solute elements in fine δ-Ni2Si precipitates, the atomic ratio of (Ni,M/Si was set as 2/1. Thus the designed alloy series of Cu93.75(Ni/Zr3.75Si2.08(Cr/Fe/Mo0.42 (at% were arc-melted into ingots under argon atmosphere, and solid-solutioned at 950 °C for 1 h plus water quenching and then aged at 450 °C for different hours. The experimental results showed that these designed alloys exhibit high hardness (HV > 1.7 GPa and good electrical conductivities (≥ 35% IACS. Specifically, the quinary Cu93.75Ni3.54Si2.08(Cr/Fe0.42Zr0.21 alloys (Cu-3.32Ni-0.93Si-0.37(Cr/Fe−0.30Zr wt% possess both a high hardness with HV = 2.5–2.7 GPa, comparable to the high-strength KLFA85 alloy (Cu-3.2Ni-0.7Si-1.1Zn wt%, HV = 2.548 GPa, and a good electrical conductivity (35–36% IACS.

Fracto- mechanoluminescence and thermoluminescence properties of orange-red emitting Eu3+ doped Ca2Al2SiO7 phosphors

International Nuclear Information System (INIS)

Tiwari, Geetanjali; Brahme, Nameeta; Sharma, Ravi; Bisen, D.P.; Sao, Sanjay K.; Khare, Ayush

2017-01-01

The suitability of nano-structured Ca 2 Al 2 SiO 7 :Eu 3+ phosphors for thermoluminescence and mechanoluminescence dosimeter were investigated. Europium doped di-calcium di-aluminum silicate phosphor was synthesised by the combustion assisted method and annealed at 1100 °C for 4 h in reducing and oxidizing environments. The prepared Ca 2 Al 2 SiO 7 :Eu 3+ phosphor was characterized by X-ray diffractometer (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) with energy dispersive x-ray spectroscopy (EDX), photoluminescence (PL) and decay characteristics. The phase structure of sintered phosphor has akermanite type which belongs to the tetragonal crystallography; this structure is a member of the melilite group and forms a layered compound. The chemical composition of the sintered Ca 2 Al 2 SiO 7 :Eu 3+ phosphor was confirmed by EDX spectra. Mechanoluminescence (ML) and thermoluminescence (TL) studies revealed that the ML and TL intensity increases with activator concentration. Optimum ML was observed for the sample having 2 mol% of Eu ions. The TL intensity of Ca 2 Al 2 SiO 7 :Eu 3+ was recorded for different exposure times of γ -irradiation and it was observed that TL intensity is maximum for γ dose of 1770 Gy. The PL spectra indicated that Ca 2 Al 2 SiO 7 :Eu 3+ could be excited effectively by near ultraviolet (NUV) light and exhibited bright orange-red emission with excellent colour stability. CIE colour coordinates of the prepared Ca 2 Al 2 SiO 7 :Eu 3+ phosphor was found suitable as orange-red light emitting phosphor with a CIE value of (x=0.6142, y=0.3849) and correlated colour temperature (CCT) is 1250 K. Therefore, it is considered to be a new promising orange-red emitting phosphor for white light emitting diode (LED) application.

Factores asociados al asma en los niños y adolescentes de la zona rural de Navarra (España

Directory of Open Access Journals (Sweden)

Itsaso Elizalde-Beiras

2018-06-01

Full Text Available Resumen: Objetivos: Conocer los factores asociados al asma y síntomas relacionados con asma en la población infantil y adolescente en la zona rural de Navarra (España a través de la validación del cuestionario ISAAC. Participantes y métodos: Estudio transversal mediante la realización del cuestionario ISAAC y variables adicionales por 797 niños y adolescentes, a través del cual se obtuvieron datos de prevalencia sobre síntomas de asma y factores asociados sin realizar ninguna prueba diagnóstica adicional. Emplazamiento: Marco de atención primaria. A través de las zonas básicas de salud se hizo la selección de la muestra y en los centros educativos de dichas zonas se realizó el cuestionario. Mediciones y resultados: El análisis estadístico se hizo a través de regresión logística, chi cuadrado e intervalo de confianza al 95%. La prevalencia asma referida es del 11,7% en niños y del 13,4% en adolescentes. En cuanto a los factores relacionados, según los valores de OR destacan: OR = 9,5 entre sibilancias y asma, y OR = 3,5 entre rinitis recientes y asma. Respecto a las sibilancias recientes, hallamos un OR = 11,5 entre despertares y sibilancias recientes, y un OR = 3,4 entre rinitis recientes y sibilancias recientes. Conclusiones: El asma referida es una enfermedad prevalente ligeramente superior en la adolescencia y la población femenina de los escolares de la zona rural. Rinitis y otros síntomas de asma están relacionados con el asma y con las sibilancias, así como la utilización de los servicios de urgencias en el caso del asma y la bronquitis con las sibilancias. Abstract: Objectives: To determine the factors associated with asthma and asthma-related symptoms in children and adolescents in rural areas of Navarre (Spain. Participants and methods: A cross-sectional study using the International Study of Asthma and Allergies in Childhood (ISAAC questionnaire, as well as additional variables, was conducted on 797

Análisis exploratorio de la percepción en niños preescolares sobre la interacción recíproca con sus madres

OpenAIRE

Pedro Solís-Cámara R.; Yolanda Medina Cuevas

2014-01-01

Aunque los avances conceptuales y las evidencias empíricas con niños en edad escolar y adolescentes sugieren que las percepciones de los niños son relevantes para comprender las interacciones recíprocas padres - hijos, el estado de conocimiento es prácticamente nulo en niños preescolares. El principal objetivo de este estudio buscó explorar la percepción de niños preescolares sobre las relaciones con sus madres y analizar si los puntajes diferenciales de la percepción de los niños indican dif...

Análisis de las funciones cognoscitivas y del lenguaje en niños escolarizados con déficit de atención con y sin hiperactividad

Directory of Open Access Journals (Sweden)

Dinora Sanchez

2013-12-01

Full Text Available Introduccion: En el modelo factorial de la organización cerebral de la cognición, existen componentes subyacentes compartidos en la estructura de coda una de las funciones cognoscitiva. Objetivos: Anali-zar las ejecuciones en las pruebas de memoria semántica y visual de puntos, de función ejecutiva, de tendón y del lenguaje en niños con deficiencia atencional con y sin hiperactividad, de 7 a 11 años y escolarizados en la ciudad de Medellín, que pudieran apoyar el modelo de factores cognoscitivos subyacentes compartidos. Pacientes y método: Se seleccionaron 32 niños con deficiencia atencional sin hiperactividad ( DDAJ-H, 28 con deficiencia atencional con hiperactividad ( DDAH-H, según los criterios del DSM-IV y con una puntuación T>60 en una checklist para DDA, y 32 controles, todos con un coeficiente intelectual manual VVISC-R ( CIM . 80 y con edades entre los 7 y los 11 años. Se recogio la edad, el sexo, la escolaridad y el estrato socioeconomico ( ESE. Se aplicaron diferentes pruebas para evaluar las fundones cognoscitivas como; subpruebas Digito - simbolo, Aritmetica y Fallas para mantener el principio de la prueba clasificacion de tarjetas del VVISCONSI para evaluar Atencion, Las pruebas de Memoria Semántica y Visual de Puntos para evaluar Memoria, la prueba clasificación de tarjetas del WISCONS, para evaluar funciones ejecutivas; y para evaluar lenguaje se utilizaron las pruebas de comprension, inferencias, narraciones, fluidez fonologica y semantica, analogias y denominacion rapida. Resultados: Los niños de ambos grupos de DDA tuvieron un coeficiente intelectual verbal ( CV, un CIM, un coeficiente intelectual total significativamente menores que los controles ( ANOVA - conexión - Bonferroni ( p <0,005 . Entre los grupos con DDA y control, se obtuvo puntuaciones significativas en la subprueba de digito - simbolo (p< 0.05, y en las subpruebas narracion, analogias, y FAS fonologico ( p<0.01 entre el grupo control y los dos

Relación de la succión no nutritiva con la maloclusión en niños ecuatorianos

Directory of Open Access Journals (Sweden)

Myriam Isabel Carrillo Valencia

2016-09-01

Full Text Available Objetivo: Determinar la relación que existe entre los Hábitos de Succión No Nutritiva (HSNN y la presencia de Maloclusiones, en los niños(as de 5 a 9 años de edad de tres Centros Educativos del cantón Ambato, Ecuador. Materiales y métodos: En el presente estudio transversal se evaluaron 435 niños de ambos sexos. El examen clínico fue realizado por un Dentista entrenado siguiendo los criterios diagnósticos de maloclusión según Hurtado et al., 2012. La recolección de datos fue a través de una ficha estructurada. Fueron estudiadas las variables relacionadas con las características propias del niño y la duración del hábito, con la presencia de HSNN y maloclusión. Los datos fueron analizados a través del test estadístico del Chi cuadrado y la correlación de Spearman con un nivel de significancia del 5%. Resultados: La prevalencia del HSNN fue del 52.6%, la prevalencia de maloclusión 38.6%, el tipo de HSNN más frecuente fue la succión digital con 21.6%, la maloclusión más frecuente fue la mordida cruzada anterior con 8.7%; en cuanto al sexo, la edad y la duración del hábito no hubo diferencias estadísticamente significativas. Conclusiones: No hubo relación estadísticamente significativa entre los HSNN y la presencia de maloclusiones, en niños(as entre 5 a 9 años de edad de los 3 centros de educación básica de la ciudad de Ambato.

Corrosion analysis of AlMg2 and AlMgSi using electrochemical method

International Nuclear Information System (INIS)

Dian A; Maman Kartaman; Rosika K; Yanlinastuti

2014-01-01

Corrosion test of cladding materials and structures of research reactor fuel, AlMgSi and AlMg2 have been performed in demineralized water of pH 2 and 6.7 using an electrochemical method. Corrosion phenomenon is affected by several factor such as composition and condition of solution. The purpose of this activity is to investigate the corrosion phenomena through the determination of the parameters of corrosion and polarization curve. The materials used are AlMg2 and AlMgSi alloy in circular dish shape with an area of 1 Cm"2. Preparation of the test sample is performed through several stages polishing, cleaning and drying procedures followed ASTM G3. The electrochemical method is done by measuring the open circuit potential (OCP), polarization resistance and potentiodynamic in demineralized water of pH 2 and pH 6.7 at temperature of 25°C. The results of the OCP is the corrosion potential (Ecorr) of AlMg2 and AlMgSi each of -906.1 mV and -619.8 mV at pH 2 and -868.6 and -756.7 mV at pH 6.7 mV. The results of measurements by polarization resistance technique showed that the corrosion rate of AlMg2 and AlMgSi in safe category (<2 mpy) at pH 6.7 and at pH 2 corrosion rate increased significantly, but still in the lightweight category (<20 mpy). Potentiodynamic curves showed that the passivation at pH 6.7 is very low while the passivation at pH 2 occurs within a relatively short range potential and followed events corroded. (author)

A new Ti-Zr-Hf-Cu-Ni-Si-Sn bulk amorphous alloy with high glass-forming ability

International Nuclear Information System (INIS)

Huang, Y.J.; Shen, J.; Sun, J.F.; Yu, X.B.

2007-01-01

The effect of Sn substitution for Cu on the glass-forming ability was investigated in Ti 41.5 Zr 2.5 Hf 5 Cu 42.5-x Ni 7.5 Si 1 Sn x (x = 0, 1, 3, 5, 7) alloys by using differential scanning calorimetry (DSC) and X-ray diffractometry. The alloy containing 5% Sn shows the highest glass-forming ability (GFA) among the Ti-Zr-Hf-Cu-Ni-Si-Sn system. Fully amorphous rod sample with diameters up to 6 mm could be successfully fabricated by the copper mold casting Ti 41.5 Zr 2.5 Hf 5 Cu 37.5 Ni 7.5 Si 1 Sn 5 alloy. The activation energies for glass transition and crystallization for Ti 41.5 Zr 2.5 Hf 5 Cu 37.5 Ni 7.5 Si 1 Sn 5 amorphous alloy are both larger than those values for the Sn-free alloy. The enhancement in GFA and thermal stability after the partial replacement of Cu by Sn may be contributed to the strong atomic bonding nature between Ti and Sn and the increasing of atomic packing density. The amorphous Ti 41.5 Zr 2.5 Hf 5 Cu 37.5 Ni 7.5 Si 1 Sn 5 alloy also possesses superior mechanical properties

Microstructural Evolution of NiCoCrAlHfYSi and NiCoCrAlTaY Coatings Deposited by AC-HVAF and APS

Science.gov (United States)

Han, Yujun; Chen, Hongfei; Gao, Dong; Yang, Guang; Liu, Bin; Chu, Yajie; Fan, Jinkai; Gao, Yanfeng

2017-12-01

The chemical composition of NiCoCrAlHfYSi with a suitable particle size, deposited using an activated combustion-high velocity air fuel (AC-HVAF) spray, is a potentially promising process because dense, continuous and pure alumina can be formed on the surface of the MCrAlY metallic coatings after isothermal oxidation exposure. The NiCoCrAlHfYSi (Amdry386) and NiCoCrAlTaY (Amdry997) coatings were produced using AC-HVAF and APS, respectively. Isothermal oxidation was subsequently conducted at 1050 °C in air for 200 h. This paper compares the characteristics of four coated samples, including the surface roughness, elastic modulus, hardness, oxide content, microstructural characteristics and phase evolution of thermally grown oxides (TGO). The growth of both the TGO and alumina scales in the TGO of the HVAF386 coating was relatively rapid. The θ- to α-alumina phase transformation was strongly determined by the Hf and Si dopants in the HVAF386 coating. Finally, the extent of grain refinement and deformation storage energy in the HVAF997 coatings were determined to be significantly crucial for the θ- to α-alumina phase transformation.

The influence of Pt redistribution on Ni1-xPtxSi growth properties

International Nuclear Information System (INIS)

Demeulemeester, J.; Smeets, D.; Temst, K.; Vantomme, A.; Comrie, C. M.; Van Bockstael, C.; Knaepen, W.; Detavernier, C.

2010-01-01

We have studied the influence of Pt on the growth of Ni silicide thin films by examining the Pt redistribution during silicide growth. Three different initial Pt configurations were investigated, i.e., a Pt alloy (Ni+Pt/ ), a Pt capping layer (Pt/Ni/ ) and a Pt interlayer (Ni/Pt/ ), all containing 7 at. % Pt relative to the Ni content. The Pt redistribution was probed using in situ real-time Rutherford backscattering spectrometry (RBS) whereas the phase sequence was monitored during the solid phase reaction (SPR) using in situ real-time x-ray diffraction. We found that the capping layer and alloy exhibit a SPR comparable to the pure Ni/ system, whereas Pt added as an interlayer has a much more drastic influence on the Ni silicide phase sequence. Nevertheless, for all initial sample configurations, Pt redistributes in an erratic way. This phenomenon can be assigned to the low solubility of Pt in Ni 2 Si compared to NiSi and the high mobility of Pt in Ni 2 Si compared to pure Ni. Real-time RBS further revealed that the crucial issue determining the growth properties of each silicide phase is the Pt concentration at the Si interface during the initial stages of phase formation. The formation of areas rich in Pt reduce the Ni silicide growth kinetics which influences the phase sequence and properties of the silicides.

Properties of P/M forged Al-Si alloys made by premixed powders. 1. Influences of dispersion and sizes of proeutectic Si on wear resistance; Kongoho ni yotte sakuseishita Al-Si kei shoketsu tanzo gokin no tokusei. 1. Taimamosei ni oyobosu shosho Si no bunsan jotai to ryukei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ishijima, Z.; Ichikawa, J.; Sasaki, s.; Shikata, H. [Hitachi Powdered Metals Co. Ltd., Tokyo (Japan)

1995-10-15

Influences of dispersion and sizes of proeutectic Si on wear resistance of P/M Al-Si alloys using the prealloying method and premixing method have been investigated. As a result, discretely dispersed proeutectic Si showed excellent wear resistance in compassion with uniformly dispersed one. The cause is considered to be the unclosed Si soft phase which has been preferentially worn away, consequently acting on forming oil grooves and burying worn particles. Further more the existence of the optimum size of proeutectic Si on wear resistance was confirmed. In the case of finer particles, only Al-Si alloy (pin) was warned away substantially. On the other handgun the case of larger particles, both the Al-Si alloy (pin) and the mating malarial (steel disc) were excessively warned away. It is assumed therefore that the finer proeutectic Si particles are not effective as hard particles, on the contrary, larger proeutectic Si particles increase the abrasive wear against the mating material, and those buried into the mating material initiate wear of Al-Si alloy at the same time. 2 refs., 10 figs., 1 tab.

Microstructure and Wear Resistance of Laser-Clad (Co, Ni61.2B26.2Si7.8Ta4.8 Coatings

Directory of Open Access Journals (Sweden)

Luan Zhang

2017-10-01

Full Text Available It has been reported that a quaternary Co61.2B26.2Si7.8Ta4.8 alloy is a good glass former and can be laser-clad to an amorphous composite coating with superior hardness and wear resistance. In this paper, alloys with varying Ni contents to substitute for Co are coated on the surface of #45 carbon steel using a 5-kW CO2 laser source for the purpose of obtaining protective coatings. In contrast to the quaternary case, the clad layers are characterized by a matrix of α-(Fe, Co, Ni solid solution plus CoB, Co3B, and Co3Ta types of precipitates. The cladding layer is divided into four regions: Near-surface dendrites, α-(Fe, Co, Ni solid solution plus dispersed particles in the middle zone, columnar bonding zone, and heat-affected area that consists of martensite. The hardness gradually decreases with increasing Ni content, and the maximum hardness occurs in the middle zone. Both the friction coefficient and wear volume are minimized in the alloy containing 12.2% Ni. Compared with the previous cobalt-based quaternary alloy Co61.2B26.2Si7.8Ta4.8, the addition of the Ni element reduces the glass-forming ability and henceforth the hardness and wear resistance of the clad layers.

High-Strength Ultra-Fine-Grained Hypereutectic Al-Si-Fe-X (X = Cr, Mn) Alloys Prepared by Short-Term Mechanical Alloying and Spark Plasma Sintering.

Science.gov (United States)

Průša, Filip; Bláhová, Markéta; Vojtěch, Dalibor; Kučera, Vojtěch; Bernatiková, Adriana; Kubatík, Tomáš František; Michalcová, Alena

2016-11-30

In this work, Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn (wt %) alloys were prepared by a combination of short-term mechanical alloying and spark plasma sintering. The microstructure was composed of homogeneously dispersed intermetallic particles forming composite-like structures. X-ray diffraction analysis and TEM + EDS analysis determined that the α-Al along with α-Al 15 (Fe,Cr)₃Si₂ or α-Al 15 (Fe,Mn)₃Si₂ phases were present, with dimensions below 130 nm. The highest hardness of 380 ± 7 HV5 was observed for the Al-20Si-10Fe-6Mn alloy, exceeding the hardness of the reference as-cast Al-12Si-1Cu-1 Mg-1Ni alloy (121 ± 2 HV5) by nearly a factor of three. Both of the prepared alloys showed exceptional thermal stability with the hardness remaining almost the same even after 100 h of annealing at 400 °C. Additionally, the compressive strengths of the Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn alloys reached 869 MPa and 887 MPa, respectively, and had virtually the same values of 870 MPa and 865 MPa, respectively, even after 100 h of annealing. More importantly, the alloys showed an increase in ductility at 400 °C, reaching several tens of percent. Thus, both of the investigated alloys showed better mechanical properties, including superior hardness, compressive strength and thermal stability, as compared to the reference Al-10Si-1Cu-1Mg-1Ni alloy, which softened remarkably, reducing its hardness by almost 50% to 63 ± 8 HV5.

El procesamiento temporal en la percepción del habla de los niños con dislexia

Directory of Open Access Journals (Sweden)

Rosario Ortiz

2014-05-01

Full Text Available Numerosos estudios muestran que un déficit fonol6gico causa la dislexia evolutiva, pero el origen de este déficit continúa siendo un tema controvertido. Este estudio examina si el déficit perceptivo fonol6gico de los niños con dislexia puede ser explicado por un déficit de procesamiento temporal mediante un diseño que controla las demandas de la tarea y la complejidad lingüística y temporal de los contrastes entre sonidos del habla. Trece niños con dislexia y déficit fonol6gico (9-11 años de edad y 13 niños sin dificultades en lectura emparejados en edad fueron evaluados en tareas de juicio de orden temporal (JOT y en tareas de discriminación igual-diferente (I-D. Las tareas se basan en contrastes de las sílabas /ba/ -/da/ y /fa/-/la/. Analizamos los efectos de la complejidad de los estímulos (similar vs. no similar y de la tarea (tarea de juicio de orden temporal vs. discriminaci6n. Los niños con dislexia muestran peor rendimiento que los niños sin dificultades en lectura en ambos pares de sílabas. El rendimiento de los niños con dislexia en las tareas JOT fue significativamente inferior que el de los niños del grupo control pero no encontramos diferencias entre los grupos en las tareas I-D. Los hallazgos son discutidos en términos de problemas de procesamiento temporal en la percepci6n del habla de los niños con dislexia.

Change of quasilattice constant during amorphous-to-quasicrystalline phase transformation in Zr65Al7.5Ni10Cu7.5Ag10 metallic glass

DEFF Research Database (Denmark)

Jiang, Jianzhong; Rasmussen, A.R.; Jensen, C.H.

2002-01-01

The amorphous-to-quasicrystalline phase transformation in a Zr65Al7.5Ni10Cu7.5Ag10 metallic glass has been investigated by monitoring the quasilattice constant and the composition of quasicrystalline particles in the samples annealed in vacuum at 663 K for various times. It is found that the quas......The amorphous-to-quasicrystalline phase transformation in a Zr65Al7.5Ni10Cu7.5Ag10 metallic glass has been investigated by monitoring the quasilattice constant and the composition of quasicrystalline particles in the samples annealed in vacuum at 663 K for various times. It is found......Cu7.5Ag10 metallic glass is a nonpolymorphous reaction....

COMPORTAMIENTO REFRACTARIO DE PROBETAS DE MORTEROS CONFORMADAS CON DIATOMITAS COMO AGREGADO MINERAL

Directory of Open Access Journals (Sweden)

Ana Rodriguez

2008-03-01

Full Text Available El objetivo de este trabajo es el estudio de las propiedades puzolánicas de algunos minerales, como las diatomitas, que potencialmente pueden reaccionar con la portlandita contenida en las pastas y morteros de cemento Portland. También se estudia si estas adiciones minerales pueden incrementar la resistencia térmica y la refractariedad de los morteros. En el comportamiento de estos agregados se sigue midiendo como parámetro el comportamientopuzolánico de las diatomitas en las pastas de cemento Portland, y las variaciones de la resistencia mecánica de probetas estandarizadas construidas con y sin agregado de diatomitas. El desarrollo experimental programado consta de tratamientostérmicos a las diatomitas, reducción de tamaño hasta compatibilidad con la granulometría del cemento Portland, ensayos de DRX, análisis de puzolanidad, construcción de probetas de morteros con y sinagregado, y finalmente la medición de sus propiedades mecánicas residuales después de haber sido sometidas a elevadas temperaturas.Del análisis de los resultados experimentales se puede informar que las diatomitas estudiadas si le confieren propiedadespuzolánicas al cemento Portland, y como consecuencia mejoran la resistencia mecánica residual de las probetas de mortero cuando son sometidas a altas temperaturas.

A Comparison in Mechanical Properties of Cermets of Calcium Silicate with Ti-55Ni and Ti-6Al-4V Alloys for Hard Tissues Replacement

Directory of Open Access Journals (Sweden)

Azim Ataollahi Oshkour

2014-01-01

Full Text Available This study investigated the impact of calcium silicate (CS content on composition, compressive mechanical properties, and hardness of CS cermets with Ti-55Ni and Ti-6Al-4V alloys sintered at 1200°C. The powder metallurgy route was exploited to prepare the cermets. New phases of materials of Ni16Ti6Si7, CaTiO3, and Ni31Si12 appeared in cermet of Ti-55Ni with CS and in cermet of Ti-6Al-4V with CS, the new phases Ti5Si3, Ti2O, and CaTiO3, which were emerged during sintering at different CS content (wt%. The minimum shrinkage and density were observed in both groups of cermets for the 50 and 100 wt% CS content, respectively. The cermets with 40 wt% of CS had minimum compressive Young’s modulus. The minimum of compressive strength and strain percentage at maximum load were revealed in cermets with 50 and 40 wt% of CS with Ti-55Ni and Ti-6Al-4V cermets, respectively. The cermets with 80 and 90 wt% of CS showed more plasticity than the pure CS. It concluded that the composition and mechanical properties of sintered cermets of Ti-55Ni and Ti-6Al-4V with CS significantly depend on the CS content in raw cermet materials. Thus, the different mechanical properties of the cermets can be used as potential materials for different hard tissues replacements.

A Comparison in Mechanical Properties of Cermets of Calcium Silicate with Ti-55Ni and Ti-6Al-4V Alloys for Hard Tissues Replacement

Science.gov (United States)

Pramanik, Sumit; Shirazi, Seyed Farid Seyed; Mehrali, Mehdi; Yau, Yat-Huang; Abu Osman, Noor Azuan

2014-01-01

This study investigated the impact of calcium silicate (CS) content on composition, compressive mechanical properties, and hardness of CS cermets with Ti-55Ni and Ti-6Al-4V alloys sintered at 1200°C. The powder metallurgy route was exploited to prepare the cermets. New phases of materials of Ni16Ti6Si7, CaTiO3, and Ni31Si12 appeared in cermet of Ti-55Ni with CS and in cermet of Ti-6Al-4V with CS, the new phases Ti5Si3, Ti2O, and CaTiO3, which were emerged during sintering at different CS content (wt%). The minimum shrinkage and density were observed in both groups of cermets for the 50 and 100 wt% CS content, respectively. The cermets with 40 wt% of CS had minimum compressive Young's modulus. The minimum of compressive strength and strain percentage at maximum load were revealed in cermets with 50 and 40 wt% of CS with Ti-55Ni and Ti-6Al-4V cermets, respectively. The cermets with 80 and 90 wt% of CS showed more plasticity than the pure CS. It concluded that the composition and mechanical properties of sintered cermets of Ti-55Ni and Ti-6Al-4V with CS significantly depend on the CS content in raw cermet materials. Thus, the different mechanical properties of the cermets can be used as potential materials for different hard tissues replacements. PMID:25538954

Microstructural characterisation of Ni75Al25 and Ni31.5Al68.5 powder particles produced by gas atomisation

International Nuclear Information System (INIS)

García-Escorial, A.; Lieblich, M.

2014-01-01

Highlight: ► Successful production of gas atomised Ni75Al25 and Ni31.5Al68.5 powder particles. ► Characterization of the as-solidified microstructure of 75 Al 25 and Ni 31.5 Al 68.5 at.% powder particles below 100 μm in size have been studied. The gas atomised Ni 75 Al 25 powder particles are mainly spherical. The solidification of this alloy is very fast, and its microstructure consists of a dendrite and lamellar structure of partially ordered γ-(Ni), γ′-Ni 3 Al L1 2 phase, and β-NiAl phase. The order increases with the powder particle size. The gas atomised Ni 31.5 Al 68.5 powder particles are also spherical in shape. The microstructure consists of Ni 2 Al 3 dendrites with interdendritic peritectic NiAl 3 and eutectic NiAl 3 + α-Al. The amount of the Ni 2 Al 3 increases as the cooling rate increases. NiAl phase is absent in the gas atomised Ni 31.5 Al 68.5 powder

El efecto de los cursos con las TIC en el funcionamiento y bienestar social

Directory of Open Access Journals (Sweden)

Deisy Acosta Ham

2010-04-01

Full Text Available Cuando se es madre de un niño con necesidades educativas especiales (NEE, se vive una serie de etapas negativas que afectan a toda la familia, pero significativamente al niño especial, cuando no se dispone de la orientación y ayuda adecuadas. Las madres, al brindar atención de tiempo completo a su hijo con NEE, hacen infuncionales sus relaciones sociales; en otras palabras, sus escalas de función y bienestar social, relacionadas con la salud, son afectadas de modo negativo. Las tecnologías de información y comunicación (TIC aparecen en este escenario para brindar información y apoyo con programas educativos, comunidades virtuales, foros, y canales de conversación que proporcionan servicios psicopedagógicos, terapia, cursos de orientación, crecimiento personal y profesional. Las TIC otorgan ayuda inmediata, comunicación y acceso a información ilimitada. ¿Cómo saber si estas tecnologías están teniendo algún efecto en el aspecto social de las madres? De ahí que el propósito del presente trabajo sea conocer si existe o no dicho efecto.

Natural attenuation in contaminated soils with hydrocarbons; Atenuacion natural en suelos contaminados con hidrocarburos

Energy Technology Data Exchange (ETDEWEB)

Corona Ramirez, L; Iturbide Arguelles, R [Facultad de Ingenieria, UNAM, Mexico, D.F. (Mexico)

2005-06-01

A contaminated soil experiment was performed using simples from a refinery, containing oil derivative hydrocarbons, specifically those with high concentrations of polyaromathic hydrocarbons (PAH). The testing consisted in 7 pans with 7 kg of soil, the preparation of 6 pans under specific conditions and one as a blank, the conditions were: water content (15 y 30%), addition a non-ionic surfactant. The process consisted in the daily aeration and water control of the samples. The PAH were analyzed: anthracene, benzo(a) pyrene, chrysene, phenanthrene and naphthalene. The results after 8 weeks showed a gradual degradation of PAH, indicating a better removal obtained when the water content was 30% with nutrients addition. [Spanish] Se realizo un experimento con suelo contaminado proveniente de una refineria, el cual contaba con hidrocarburos derivados de petroleo, especificamente con concentraciones elevadas de hidrocarburos poliaromaticos (HAP). El estudio consistio en preparar 7 cajones con 7 kg de suelo, cada uno con las siguientes condiciones: S1suelo contaminado con hidrocarburos y 15% de contenido de agua. S2 suelo contaminado con hidrocarburo y adicion de Nitrogeno y Fosforo (N y P) con 15% de contenido de agua. S3 suelo contaminado con hidrocarburo y adicion de N y P mas un surfactante no ionico, Emulgin W600, con 15% de contenido de agua. S4 igual a S1 pero con 30% de contenido de agua. S5 igual a S2, con 30% de contenido de agua. S6 igual S3 con 30% de contenido de agua. S7 suelo contaminado testigo, sin control de humedad y sin aireacion. La experimentacion consistio en airear el suelo diariamente y controlar el contenido de agua de manera que este fuera constante. Los resultados, indican que la mejor remocion se obtuvo para el contenido de agua de 30%, con adicion de nutrientes y surfactante. Los compuestos con mayor eficiencia de remocion para todas las opciones son naftaleno y antraceno. Por lo tanto, de acuerdo con los resultados, los compuestos

Effects of C+ ion implantation on electrical properties of NiSiGe/SiGe contacts

International Nuclear Information System (INIS)

Zhang, B.; Yu, W.; Zhao, Q.T.; Buca, D.; Breuer, U.; Hartmann, J.-M.; Holländer, B.; Mantl, S.; Zhang, M.; Wang, X.

2013-01-01

We have investigated the morphology and electrical properties of NiSiGe/SiGe contact by C + ions pre-implanted into relaxed Si 0.8 Ge 0.2 layers. Cross-section transmission electron microscopy revealed that both the surface and interface of NiSiGe were improved by C + ions implantation. In addition, the effective hole Schottky barrier heights (Φ Bp ) of NiSiGe/SiGe were extracted. Φ Bp was observed to decrease substantially with an increase in C + ion implantation dose

Self-assembled epitaxial NiSi2 nanowires on Si(001) by reactive deposition epitaxy

International Nuclear Information System (INIS)

Chen, S.Y.; Chen, L.J.

2006-01-01

Self-assembled epitaxial NiSi 2 nanowires have been fabricated on Si(001) by reactive deposition epitaxy (RDE). The RDE method promoted nanowire growth since it provides deposited atoms sufficient kinetic energy for movement on the Si surface during the growth of silicide islands. The twin-related interface between NiSi 2 and Si is directly related to the nanowire formation since it breaks the symmetry of the surface and leads to the asymmetric growth. The temperature of RDE was found to greatly influence the formation of nanowires. By RDE at 750 deg. C, a high density of NiSi 2 nanowires was formed with an average aspect ratio of 30

Electronic structure of Ni/sub 3/Al and Ni/sub 3/Ga alloys

CERN Document Server

Pong, W F; Chang, Y K; Tsai, M H; Hsieh, H H; Pieh, J Y; Tseng, P K; Lee, J F; Hsu, L S

1999-01-01

This work investigates the charge transfer and Al(Ga) p-Ni d hybridization effects in the intermetallic Ni/sub 3/Al(Ni/sub 3/Ga) alloy using the NiL/sub 3.2/- and K-edge and Al(Ga)K X-ray absorption near edge structure (XANES) measurements. We find that the intensity of white-line features at the NiL/sub 3.2/-edge in the Ni/sub 3/Al(Ni /sub 3/Ga) alloy decreased in comparison with that of pure Ni, which can be attributed to the enhancement of Ni3d states filling and the depletion of the density of Ni 3d unoccupied states in the Ni/sub 3 /Al(Ni/sub 3/Ga) alloy. Two clear features are also observed in the Ni/sub 3/Al(Ni/sub 3/Ga) XANES spectrum at the Al(Ga) K-edge, which can be assigned to the Al(Ga) unoccupied 3p (4p) states and their hybridized states with the Ni 3d/4sp states above the Fermi level in Ni/sub 3/Al(Ni/sub 3/Ga). The threshold at Al K-edge XANES for Ni/sub 3/Al clearly shifts towards higher photon energies relative to that of pure Al, indicating that Al loses charges upon forming Ni/sub 3 /Al. ...

Effect of Ni Addition on the Wear and Corrosion Resistance of Fe-20Cr-1.7C-1Si Hardfacing Alloy

International Nuclear Information System (INIS)

Lee, Sung Hoon; Kim, Ki Nam; Kim, Seon Jin

2011-01-01

In order to improve the corrosion resistance of Fe-20Cr-1.7C-1Si hardfacing alloy without a loss of wear resistance, the effect of Ni addition was investigated. As expected, the corrosion resistance of the alloy increased with increasing Ni concentration. The wear resistance of the alloy did not decrease, even though the hardness decreased, up to Ni concentration of 5 wt.%. This was attributed to the fact that the decrease in hardness was counterbalanced by the strain-induced martensitic transformation. The wear resistance of the alloy, however, decreased abruptly with increases of the Ni concentration over 5 wt.%.

Magnetic porous PtNi/SiO2 nanofibers for catalytic hydrogenation of p-nitrophenol

Science.gov (United States)

Guan, Huijuan; Chao, Cong; Kong, Weixiao; Hu, Zonggao; Zhao, Yafei; Yuan, Siguo; Zhang, Bing

2017-06-01

In this work, the mesoporous SiO2 nanofibers from pyrolyzing precursor of electrospun nanofibers were employed as support to immobilize PtNi nanocatalyst (PtNi/SiO2 nanofibers). AFM, XRD, SEM, TEM, XPS, ICP-AES and N2 adsorption/desorption analysis were applied to systematically investigate the morphology and microstructure of as-prepared products. Results showed that PtNi alloy nanoparticles with average diameter of 18.7 nm were formed and could be homogeneously supported on the surface of porous SiO2 nanofiber, which further indicated that the SiO2 nanofibers with well-developed porous structure, large specific surface area, and roughened surface was a benefit for the support of PtNi alloy nanoparticles. The PtNi/SiO2 nanofibers catalyst exhibited an excellent catalytic activity towards the reduction of p-nitrophenol, and the catalyst's kinetic parameter ( k n = 434 × 10-3 mmol s-1 g-1) was much higher than those of Ni/SiO2 nanofibers (18 × 10-3 mmol s-1 g-1), Pt/SiO2 nanofibers (55 × 10-3 mmol s-1 g-1) and previous reported PtNi catalysts. The catalyst could be easily recycled from heterogeneous reaction system based on its good magnetic properties (the Ms value of 11.48 emu g-1). In addition, PtNi/SiO2 nanofibers also showed an excellent stability and the conversion rate of p-nitrophenol still could maintain 94.2% after the eighth using cycle.

Análisis del Perfil Cardiovascular en Niños y Adolescentes con epilepsia idiopática

Directory of Open Access Journals (Sweden)

Randy Guerra-Olivares

2014-04-01

Full Text Available Introducción: El uso apropiado de ácido valproico y carbamazepina ha mostrado marcada eficacia para el control de las crisis en pacientes con diagnostico de epilepsia; sin embargo, se ha visto asociado a ciertos efectos secundarios. Entre ellos, cobran especial importancia aquellos que afectan el peso corporal y el perfil bioquímico. Objetivo: Evaluar la presencia de factores de riesgo cardiovasculares en niños y adolescentes diagnosticados con epilepsia idiopática, tratados en monoterapia con ácido valproico o carbamazepina. Métodos: Estudio analítico de corte transversal en niños y adolescentes con diagnóstico de epilepsia en monoterapia con alguna de las dos drogas mencionadas, a quienes se les realizó toma de medidas antropométricas como peso y talla, se calculó índice de masa corporal y se tomaron muestras de sangre para realizar cuantificación en suero de la droga, glucemia y perfiles lipídicos. Resultados: Del total de 30 pacientes, 14 fueron medicados con ácido valproico y 16 con carbamazepina, edad promedio del primer grupo, 9,4 años (IC95% 7,0 a 10,9, 50 % género masculino; (IC95% 26,8 a 73,2 recibiendo dosis promedio de de 26,8 mg/kg/día. Grupo carbamazepina, con edades promedio de 10,3 años (IC95% 8,8 a 11,8, 9 pacientes masculinos (56,3 %; IC95% 33,2 a 76,9 y 7 femeninos (43,7 %; IC95% 23,1 a 66,8, recibiendo dosis promedio de 14,1 mg/kg/día (IC95% 12,6-15.7; mínimo 8,8 y máximo 21,3. Del total de niños 26,7 % presentaban retardo de crecimiento y el 73,3 % normalidad. Todos los casos tuvieron glucemias menores de 100 mg/dL y triglicéridos mayores de 100 mg/dL. En el grupo de carbamazepina, 75% presentaban hipercolesterolemia (≥ 170 mg/dL superior al grupo ácido valproico (21,4 %; 3/14; con diferencia de proporciones (IC95% 18 a 74 %; p = 0,003*. Conclusiones: Los resultados obtenidos sugieren que es necesario considerar las alteraciones del perfi l lipídico en relación del tratamiento con cualquiera de

Microstructure and mechanical properties of Cu-Ni-Si alloys

International Nuclear Information System (INIS)

Monzen, Ryoichi; Watanabe, Chihiro

2008-01-01

The microstructure and mechanical properties of 0.1 wt.% Mg-added and Mg-free Cu-2.0 wt.% Ni-0.5 wt.% Si alloys aged at 400 deg. C have been examined. The addition of Mg promotes the formation of disk-shaped Ni 2 Si precipitates. The Cu-Ni-Si-Mg alloy exhibits higher strength and resistance to stress relaxation than the Cu-Ni-Si alloy. The higher strength or stress relaxation resistance is attributable to the reduction in inter-precipitate spacing by the Mg addition or the drag effect of Mg atoms on dislocation motion. The Cu-Ni-Si alloy with a large grain size of 150 μm shows higher stress relaxation resistance than the alloy with a small grain size of 10 μm because of a lower density of mobile dislocations in the former alloy

Microstructure and mechanical properties of Cu-Ni-Si alloys

Energy Technology Data Exchange (ETDEWEB)

Monzen, Ryoichi [Division of Innovative Technology and Science, Graduate School of Natural Science and Technology, Kanzawa University, Kakuma-machi, Kanazawa 920-1192 (Japan)], E-mail: monzen@t.kanazawa-u.ac.jp; Watanabe, Chihiro [Division of Innovative Technology and Science, Graduate School of Natural Science and Technology, Kanzawa University, Kakuma-machi, Kanazawa 920-1192 (Japan)

2008-06-15

The microstructure and mechanical properties of 0.1 wt.% Mg-added and Mg-free Cu-2.0 wt.% Ni-0.5 wt.% Si alloys aged at 400 deg. C have been examined. The addition of Mg promotes the formation of disk-shaped Ni{sub 2}Si precipitates. The Cu-Ni-Si-Mg alloy exhibits higher strength and resistance to stress relaxation than the Cu-Ni-Si alloy. The higher strength or stress relaxation resistance is attributable to the reduction in inter-precipitate spacing by the Mg addition or the drag effect of Mg atoms on dislocation motion. The Cu-Ni-Si alloy with a large grain size of 150 {mu}m shows higher stress relaxation resistance than the alloy with a small grain size of 10 {mu}m because of a lower density of mobile dislocations in the former alloy.

Impacto nutricio del consumo de una leche entera adicionada con vitaminas y minerales en niños

Directory of Open Access Journals (Sweden)

Maulen-Radovan Irene

1999-01-01

Full Text Available OBJETIVO: Determinar el impacto nutricio del consumo de leche entera fortificada con vitaminas y minerales en niños. MATERIAL Y MÉTODOS: Se hizo un estudio prospectivo, longitudinal, en 227 niños de entre 8 a 60 meses de edad. Se ofreció a los menores 500 ml diarios de leche entera fortificada por 90 días. Se registró ingestión, aceptación, peso, talla, hemoglobina (Hb, hierro (Fe, vitamina B12 y folatos séricos. El análisis estadístico se realizó con medidas de tendencia central y dispersión en variables dimensionales utilizando prueba t de Student para comparación de promedios y ji² para variables nominales. RESULTADOS: Al inicio de la suplementación 45 niños estaban desnutridos, y 36, anémicos. Al final de la misma estas cifras disminuyeron: 35 desnutridos (p< 0.21 y 18 niños anémicos (p< 0.01. Al inicio nueve niños tenían desnutrición severa y, al finalizar, sólo eran cinco los que la padecían. La comparación ingreso-egreso en los datos antropométricos fue como sigue (media±desviación estándar: Z peso/talla, -0.35±0.88 vs. -0.14±0.9 (p= 0.01; Hb en g/dl, 11±1.3 vs. 11.9±1.9 (p< 0.001; Fe en mg/dl, 108±44 vs. 115±31 (p= 0.06; vitamina B12 en pg/ml, 649±494 vs. 1 053±854 (p< 0.001. El apego y la aceptación fueron de 100 y 85%, respectivamente. CONCLUSIONES: El consumo de leche entera fortificada durante 90 días mejora significativamente el estado nutricio de los niños, reduce significativamente el número de niños con anemia e incrementa los niveles plasmáticos de Hb, Vitamina B12 y folatos.