Synthesis by Sol-gel and characterization of catalysts Ag/Al2O3-CeO2

International Nuclear Information System (INIS)

Zayas, M.L.; Perez H, R.; Rubio, E.; Velasco, A.

2004-01-01

Aluminia, cerium and mixed oxides Al 2 O 3 -CeO 2 with different relationship Al/Ce (0.75, 0.50 and 0.25) were prepared by sol-gel and used as support for the Ag. The samples were characterized by XRD, DRIFT, TPR and adsorption of N 2 to temperature of liquid nitrogen. The surface area BET showed that the materials that contain aluminia present near values among them. XRD allowed to identify to the cerianite in the oxides that whose support contains cerium and to the α-aluminia. A mixture of phases was observed in the aluminia. Vibration bands attributed to the bond Al-O and Ce-O were observed by DRIFT in the catalytic materials. TPR showed differences in the reducibility of the Ag precursor in the indicative catalysts of a different interaction with the support. (Author)

Fast wave power flow along SOL field lines in NSTX

Science.gov (United States)

Perkins, R. J.; Bell, R. E.; Diallo, A.; Gerhardt, S.; Hosea, J. C.; Jaworski, M. A.; Leblanc, B. P.; Kramer, G. J.; Phillips, C. K.; Roquemore, L.; Taylor, G.; Wilson, J. R.; Ahn, J.-W.; Gray, T. K.; Green, D. L.; McLean, A.; Maingi, R.; Ryan, P. M.; Jaeger, E. F.; Sabbagh, S.

2012-10-01

On NSTX, a major loss of high-harmonic fast wave (HHFW) power can occur along open field lines passing in front of the antenna over the width of the scrape-off layer (SOL). Up to 60% of the RF power can be lost and at least partially deposited in bright spirals on the divertor floor and ceiling [1,2]. The flow of HHFW power from the antenna region to the divertor is mostly aligned along the SOL magnetic field [3], which explains the pattern of heat deposition as measured with infrared (IR) cameras. By tracing field lines from the divertor back to the midplane, the IR data can be used to estimate the profile of HHFW power coupled to SOL field lines. We hypothesize that surface waves are being excited in the SOL, and these results should benchmark advanced simulations of the RF power deposition in the SOL (e.g., [4]). Minimizing this loss is critical optimal high-power long-pulse ICRF heating on ITER while guarding against excessive divertor erosion.[4pt] [1] J.C. Hosea et al., AIP Conf Proceedings 1187 (2009) 105. [0pt] [2] G. Taylor et al., Phys. Plasmas 17 (2010) 056114. [0pt] [3] R.J. Perkins et al., to appear in Phys. Rev. Lett. [0pt] [4] D.L. Green et al., Phys. Rev. Lett. 107 (2011) 145001.

Effect of Al and N on the toughness of heavy section steel plates

International Nuclear Information System (INIS)

Kikutake, Tetsuo; Tokunaga, Yoshikuni; Nakao, Hitoji; Ito, Kametaro; Takaishi, Shogo.

1988-01-01

The effect of Al and N on the notch toughness and tensile strength of heavy section pressure vessel steel plates is investigated. Notch toughness of steel A533B (Mn-Mo-Ni), which has mixed microstructure of ferrite and bainite, is drastically changed by the ratio of sol.N/sol.Al. With metallurgical observations, it is revealed that AlN morphology is influenced by the ratio of sol.N/sol.Al through the level of solute Al(C Al ). At the heat treatment of heavy section steel plate, AlN shows OSTWALD ripening and its speed depends upon C Al . When Al is added (Al ≥ 0.010%) in steel and sol.N/sol.Al ≤ 0.5, C Al remains low. This prevents AlN ripening, and brings fine austenite grain size and high toughness. On the other hand, when sol.N/sol.Al Al becomes high and this gives poor toughness through coarse AlN precipitates and coarse austenite grain. Therefore, controll of sol.N/sol.Al over 0.5 is favorable to keep high toughness in A533B steel. In steel A387-22 (Cr-Mo) which has full bainitic microstructure, too fine austenite grain brings about poor hardenability, and polygonal ferrite, which brings about both poor strength and tughness, appears in microstructure. Then sol.N/sol.Al < 0.5 is better to give high hardenability in steel A387-22. (author)

Slow Release of Plant Volatiles Using Sol-Gel Dispensers.

Science.gov (United States)

Bian, L; Sun, X L; Cai, X M; Chen, Z M

2014-12-01

The black citrus aphid, also known as the tea aphid, (Toxoptera aurantii Boyer) attacks economically important crops, including tea (Camellia sinensis (L.) O. Kuntze). In the current study, silica sol-gel formulations were screened to find one that could carry and release C. sinensis plant volatiles to lure black citrus aphids in a greenhouse. The common plant volatile trans-2-hexen-1-al was used as a model molecule to screen for suitable sol-gel formulations. A zNose (Electronic Sensor Technology, Newbury Park, CA) transportable gas chromatograph was used to continuously monitor the volatile emissions. A sol-gel formulation containing tetramethyl orthosilicate and methyltrimethoxysilane in an 8:2 (vol:vol) ratio was selected to develop a slow-release dispenser. The half-life of trans-2-hexen-1-al in the sol-gel dispenser increased slightly with the volume of this compound in the dispenser. Ten different volatiles were tested in the sol-gel dispenser. Alcohols of 6-10 carbons had the longest half-lives (3.01-3.77 d), while esters of 6-12 carbons had the shortest (1.53-2.28 d). Release of these volatiles from the dispensers could not be detected by the zNose after 16 d (cis-3-hexenyl acetate) to 26 d (3,7-dimethylocta-1,6-dien-3-ol). In greenhouse experiments, trans-2-hexen-1-al and cis-3-hexen-1-ol released from the sol-gel dispensers attracted aphids for ≍17 d, and release of these volatiles could not be detected by the zNose after ≍24 d. The sol-gel dispensers performed adequately for the slow release of plant volatiles to trap aphids in the greenhouse. © 2014 Entomological Society of America.

Studies of (3-mercaptopropyl)trimethoxylsilane and bis(trimethoxysilyl)ethane sol-gel coating on copper and aluminum.

Science.gov (United States)

Li, Ying-Sing; Lu, Weijie; Wang, Yu; Tran, Tuan

2009-09-01

Bis(trimethoxysilyl)ethane (BTMSE) and (3-mercaptopropyl)trimethoxysilane (MPTMS) have been used as precursors to prepare sol-gels and hybrid sol-gel under acidic condition. From the X-ray photoelectron spectroscopy data on MPTMS sol-gel coated aluminum and copper, it has been shown that the silane film is covalently bonded to Al surface through the interfacial condensation. There is no evidence of bonding interaction between the thiol group and the Cu. The recorded reflection adsorption IR (RAIR) spectrum has provided evidence that the coating BTMSE film covalently interacts with Al. Vibrational assignments have been suggested for pure BTMSE, BTMSE sol-gel, BTMSE xerogel, and BTMSE coated Al panel based on the group frequencies and the variation of frequencies with the sample treatment conditions. The progression of condensation reaction has been observed from the IR spectra of the BTMSE sol-gel and the sol-gel coated film after the treatments at different temperatures with different lengths of time. The corrosion protection of the sol-gel coated Al and Cu has been characterized in NaCl solutions by cyclic voltammetric, potentiodynamic polarization and impedance spectroscopy methods. All these electrochemical measurements indicate that the sol-gel coated metals have better corrosion protection than the corresponding uncoated metals.

Sol-gel derived zinc oxide films alloyed with cobalt and aluminium

International Nuclear Information System (INIS)

Sharma, Mamta; Mehra, R.M.

2010-01-01

ZnO films codoped with 5 at.% Co and 1 at.% Al were prepared by sol-gel technique on corning glass and silicon substrates with precursor sols of different pH values. The pH was varied from 5.4 to 11 by adding varying amounts of monoethanolamine to the sol. Since pH plays an important role in controlling the properties of films, we discuss in detail the effect of pH value on the structural, morphological and optical properties of the grown films. X-ray diffraction and atomic force microscopy images reveal that the size of crystallites increases with pH of the sol. The variation of pH in the reaction system influences the density of homogeneous nucleation and the crystal growth along the c-axis. High quality Co and Al codoped ZnO films annealed at 600 o C have been obtained using a sol with pH = 9. These sol-gel derived films find their suitability to be used as dilute magnetic semiconductors.

Sol-gel derived zinc oxide films alloyed with cobalt and aluminium

Energy Technology Data Exchange (ETDEWEB)

Sharma, Mamta [Department of Electronic Science, University of Delhi South Campus, Benito Juarez Road, New Delhi 110 021 (India); Mehra, R.M., E-mail: rammehra2003@yahoo.co [Department of Electronic Science, University of Delhi South Campus, Benito Juarez Road, New Delhi 110 021 (India)

2010-05-03

ZnO films codoped with 5 at.% Co and 1 at.% Al were prepared by sol-gel technique on corning glass and silicon substrates with precursor sols of different pH values. The pH was varied from 5.4 to 11 by adding varying amounts of monoethanolamine to the sol. Since pH plays an important role in controlling the properties of films, we discuss in detail the effect of pH value on the structural, morphological and optical properties of the grown films. X-ray diffraction and atomic force microscopy images reveal that the size of crystallites increases with pH of the sol. The variation of pH in the reaction system influences the density of homogeneous nucleation and the crystal growth along the c-axis. High quality Co and Al codoped ZnO films annealed at 600 {sup o}C have been obtained using a sol with pH = 9. These sol-gel derived films find their suitability to be used as dilute magnetic semiconductors.

Characterization of nanocrystalline ZnO:Al films by sol-gel spin coating method

Energy Technology Data Exchange (ETDEWEB)

Gareso, P. L., E-mail: pgareso@gmail.com; Rauf, N., E-mail: pgareso@gmail.com; Juarlin, E., E-mail: pgareso@gmail.com [Department of Physics, Faculty of Mathematics and Natural Sciences, Hasanuddin University, Makassar 90245 (Indonesia); Sugianto,; Maddu, A. [Department of Physics, Faculty of Mathematics and Natural Sciences, Bogor Institute of Culture, IPB Bogor (Indonesia)

2014-09-25

Nanocrystalline ZnO films doped with aluminium by sol-gel spin coating method have been investigated using optical transmittance UV-Vis and X-ray diffraction (X-RD) measurements. ZnO films were prepared using zinc acetate dehydrate (Zn(CH{sub 3}COO){sub 2}@@‡2H{sub 2}O), ethanol, and diethanolamine (DEA) as a starting material, solvent, and stabilizer, respectively. For doped films, AlCl{sub 3} was added to the mixture. The ZnO:Al films were deposited on a transparent conductive oxide (TCO) substrate using spin coating technique at room temperature with a rate of 3000 rpm in 30 sec. The deposited films were annealed at various temperatures from 400°C to 600°C during 60 minutes. The transmittance UV-Vis measurement results showed that after annealing at 400°C, the energy band gap profile of nanocrystalline ZnO:Al film was a blue shift. This indicated that the band gap of ZnO:Al increased after annealing due to the increase of crystalline size. As the annealing temperature increased the bandgap energy was a constant. In addition to this, there was a small oscillation occurring after annealing compared to the as–grown samples. In the case of X-RD measurements, the crystalinity of the films were amorphous before annealing, and after annealing the crystalinity became enhance. Also, X-RD results showed that structure of nanocrystalline ZnO:Al films were hexagonal polycrystalline with lattice parameters are a = 3.290 Å and c = 5.2531 Å.

Preparation of CuAlO2 Thin Films by Sol-Gel Method Using Nitrate Solution Dip-Coating

Directory of Open Access Journals (Sweden)

Ehara Takashi

2016-01-01

Full Text Available CuAlO2 thin films are prepared by sol-gel dip-coating followed by annealing in nitrogen atmosphere using copper nitrate and aluminum nitrate as metal source materials. X-ray diffraction (XRD patterns show (003, (006 and (009 oriented peaks of CuAlO2 at annealing temperature of 800 – 1000°C. This result indicates that the CuAlO2 films prepared in the present work are c-axis oriented. XRD peak intensity increase with annealing temperature and becomes maximum at 850°C. The CuAlO2 XRD peak decreased at annealing temperature of 900°C with appearance of a peak of CuO, and then increased again with annealing temperature until 1000 °C. The films have bandgap of 3.4 eV at annealing temperature of 850°C in which the transparency becomes the highest. At the annealing temperature of 850°C, scanning electron microscope (SEM observation reveals that the films are consist of amorphous fraction and microcrystalline CuAlO2 fraction.

Fabrication and application of mesoporous TiO{sub 2} film coated on Al wire by sol-gel method with EISA

Energy Technology Data Exchange (ETDEWEB)

Zhao, Linkang; Lu, Jianjun, E-mail: lujianjunktz@tyut.edu.cn

2017-04-30

Highlights: • Successfully fabricated mesoporous TiO{sub 2} thin film on Al wire by sol-gel method with EISA. • Ni supported on this film and exhibits good methanation performance. • Investigate the decomposition temperature of template agent F127 in TiO{sub 2} precursor system. - Abstract: Mesoporous TiO{sub 2} film on Al wire was fabricated by sol-gel method with evaporation induced self assembly (EISA) process using F127 as templating agent in the mixed solution of ethanol and Tetra-n-butyl Titanate. The Ni/TiO{sub 2} film catalyst supported on Al wire was prepared by impregnation and the catalytic performance on methanation was carried out in a titanium alloy micro-reactor tube. It was shown that anatase mesoporous TiO{sub 2} film was prepared in this conditions (1 g F127,calcined at 400 °C and aged for 24 h), which has specific surface area of 127 m{sup 2} g{sup −1} and narrow pore size distribution of 5.3 nm. Low calcined temperature (300 °C) cannot transfer film to anatase and decompose F127 completely. Ni/TiO{sub 2} film on Al wire catalyst was proved to be active in CO methanation reaction. And the CO conversion reaches 99% and CH{sub 4} selectivity close is to 80% when the reaction temperature is higher 360 °C.

Synthesis by Sol-gel and characterization of catalysts Ag/Al{sub 2}O{sub 3}-CeO{sub 2}; Sintesis por Sol-gel y caracterizacion de catalizadores Ag/Al{sub 2}O{sub 3}-CeO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zayas, M.L.; Perez H, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Rubio, E. [BUAP, Centro de Vinculacion, 72000 Puebla (Mexico); Velasco, A. [BUAP, Facultad de Quimica, 72000 Puebla (Mexico)

2004-07-01

Aluminia, cerium and mixed oxides Al{sub 2}O{sub 3}-CeO{sub 2} with different relationship Al/Ce (0.75, 0.50 and 0.25) were prepared by sol-gel and used as support for the Ag. The samples were characterized by XRD, DRIFT, TPR and adsorption of N{sub 2} to temperature of liquid nitrogen. The surface area BET showed that the materials that contain aluminia present near values among them. XRD allowed to identify to the cerianite in the oxides that whose support contains cerium and to the {alpha}-aluminia. A mixture of phases was observed in the aluminia. Vibration bands attributed to the bond Al-O and Ce-O were observed by DRIFT in the catalytic materials. TPR showed differences in the reducibility of the Ag precursor in the indicative catalysts of a different interaction with the support. (Author)

Characterisation of a new alkoxide sol-gel hydroxyapatite

International Nuclear Information System (INIS)

Green, D.D.; Kannangara, G.S.K.; Milev, A.; Ben-Nissan, B.

1999-01-01

Hydroxyapatite (HAp) coatings have been used to promote bone growth and fixation towards implant surfaces to encourage faster recovery times for the recipient. Current coating processing techniques, capable of producing thin HAp layers are pulsed-laser deposition and sputtering (high-temperature processing). Other technologies are in vitro methods, electrodeposition and sol-gel, due to the fact that these techniques utilise lower processing temperatures they avoid structural instabilities of HAp at elevated temperatures. The term sol-gel encompasses any process of producing ceramic materials (single and mixed oxides, as well as non-oxides e.g. nitrides) from solutions. The sol-gel process was first identified by Ebelman, and has been used to produce ceramic powders, coatings, and bulk materials including glasses. The implementation of a sol-gel methodology enables increased stoichiometry and homogeneity, while having the ability to coat complex shapes. Sol-gel hydroxyapatite reported by Chai et al. employed tri ethyl phosphite [ P(OEt) 3 ] as the staring phosphorus alkoxide precursor, whereby it was established that in order to obtain monophasic hydroxyapatite upon firing there must be a 24 hour ripening period. The ripening period was determined to be an equilibrium step whereby the equilibrium intermediate phase lied in favour of a diethyl phosphite arrangement (species) within the sol. Therefore, the work here under taken was to produce hydroxyapatite using diethyl phosphite [HOP(OEt) 2 ] as a starting alkoxide precursor with a final aim to reduce or eliminate the ageing period as observed by Chai et al in P(OEt) 3 solutions

La utilidad de una obra sobre el uso tipográfico en el lenguaje escrito

Directory of Open Access Journals (Sweden)

Pedro Pérez Cuadrado

2015-01-01

Full Text Available Un acercamiento a la obra Ortotipografía para diseñadores, de Raquel Martín Álvarez, que no es únicamente tal, sino un acertado compendio de 128 páginas que acierta a resumir los conocimientos de autores tan sabios en el uso tipográfico como José Martínez de Sousa, Josep Maria Pujol y Joan Solà. Una obra de comunicación aplicada al cien por cien y sobre la aplicación del lenguaje, valga el juego de palabras.

Managing of the sun in the architecture; Manejo del sol en la arquitectura

Energy Technology Data Exchange (ETDEWEB)

Gomez Azpeitia, Luis Gabriel [Facultad de Arquitectura y Diseno, Universidad de Colima (Mexico)

2005-07-01

The solar energy is the source responsible for most of the climatic processes that occur in the planet. From its magnitude, but mainly from its angle of incidence on the atmosphere and on the surface of the oceans and the Earth, depend the daily and seasonal fluctuations of temperature, and therefore the changes in the atmosphere's humidity content as well as pressure differentials that in their turn generate wind currents as well. The architecture, as an integral part of the earth surface, is interrelated with the sun since the relative position of the sun in respect to the buildings is fundamental to obtain energy efficiency as well as comfort in the inhabitants and adjustment to the surroundings. Hence the requirement that the architects formulate their projects in agreement to the sun path, to the different seasons of the year, either to avoid their radiation or to take advantage of it. In this presentation, it is intended to make a fast review of all the tools of support so that the architects recommend the practical use of some of them and so to demonstrate with a practical example the utility that they have in the process of architectural design. [Spanish] La energia solar es la fuente responsable de la mayor parte de los procesos climaticos que ocurren en el planeta. De su magnitud, pero sobre todo de su angulo de incidencia sobre la atmosfera y sobre la superficie de los oceanos y de la tierra, dependen las fluctuaciones de temperaturas diarias y estacionales, y por lo tanto cambios en el contenido de humedad de la atmosfera asi como diferencias de presion que a su vez generan las corrientes de viento. La arquitectura, como parte integral de la superficie terrestre esta interrelacionada con el sol, ya que la posicion relativa del sol con respecto a los edificios es fundamental para lograr eficiencia energetica, confort en los habitantes y adecuacion al entorno. De ahi la exigencia de que los arquitectos formulen sus proyectos en concordancia a la

Scratch resistance of SiO{sub 2} and SiO{sub 2} - ZrO{sub 2} sol-gel coatings on glass-ceramic obtained by sintering; Resistencia al desgaste de recubrimientos sol-gel de SiO{sub 2} y SiO{sub 2} - ZrO{sub 2} sobre materiales vitroceramicos obtenidos por sinterizacion

Energy Technology Data Exchange (ETDEWEB)

Soares, V. O.; Soares, P.; Peitl, O.; Zanotto, E. D.; Duran, A.; Castro, Y.

2013-10-01

The sol-gel process is widely used to obtain coatings on glass-ceramic substrates in order to improve the scratch and abrasion resistance, also providing a bright and homogeneous appearance of a glaze avoiding expensive final polishing treatments. This paper describes the preparation of silica and silica / zirconia coatings by sol-gel method on Li{sub 2}O-Al{sub 2}O3-SiO{sub 2} (LAS) glassceramic substrates produced by sintering. The coatings were deposited by dip-coating on LAS substrates and characterized by optical microscopy and spectral ellipsometry. On the other hand, hardness and elastic modulus, coefficient of friction and abrasion and scratch resistance of the coatings were determined and compared with the substrate properties. Coatings deposited on LAS glass-ceramic confere the substrate a bright and homogeneous aspect, similar to a glaze, improving the appearance and avoiding the final polishing. However these coatings do not increase the scratch resistance of the substrate only equaling the properties of the glass-ceramic. (Author)

Adolfo Bioy casares y Mario Bellatin: sobre cartas sin cuerpo y acantilados

Directory of Open Access Journals (Sweden)

Karla Fernandes Cipreste

2016-10-01

Full Text Available Se propone una lectura de dos escritores hispanoamericanos – Adolfo Bioy Casares y Mario Bellatin – con el propósito de reflexionar sobre discursos de poder, incluido el ámbito de la Crítica Latinoamericana. Se entienden las experiencias de los personajes de sus obras, y también el ethos de ambos los autores, como una existência ética y estética que resiste a los intentos de categorizaciones. La propuesta se hace a la luz del concepto de Comunidad, del filósofo italiano Roberto Esposito, y de la discusión de Hugo Achugar sobre lo local y lo global en América Latina. Dos imágenes inspiran ese análisis: la carta sin cuerpo en Dormir al sol, de Casares; y el acantilado de Bellatin en Los fantasmas del masajista.

Biocompatibility of bismuth silicate coatings deposited on 316L stainless steel by sol-gel process

Directory of Open Access Journals (Sweden)

Jorge Hernando Bautista-Ruiz

2017-01-01

Full Text Available Películas delgadas de silicato de bismuto (BSO se han fabricado mediante el proceso sol-gel. El sol estable se sintetizó utilizando nitrato de bismuto (III pentahidrato y tetraetil-ortosilicato (TEOS. Las películas fueron depositadas a 1500 rpm mediante la técnica de centrifugado. Los recubrimientos se caracterizaron por microscopía de fuerza atómica (AFM, microscopía electrónica de barrido (SEM, difracción de rayos-X (DRX y se midió el espesor de las películas. El objetivo de este estudio fue evaluar la adhesión y la proliferación en células de osteoblastos, mediante el ensayo MMT, al incubarse sobre películas BSO en sustratos de 316L. Se concluyó que el crecimiento de los osteoblastos es homogéneo en la superficie de las películas, indicando que el medio ofrecido por los recubrimientos no presenta actividad citotóxica y favorece los niveles de crecimiento celular en comparación con los resultados obtenidos para los sustratos de acero inoxidable.

Radiation hardening in sol-gel derived Er3+-doped silica glasses

International Nuclear Information System (INIS)

Hari Babu, B.; León Pichel, Mónica; Ollier, Nadège; El Hamzaoui, Hicham; Bigot, Laurent; Savelii, Inna; Bouazaoui, Mohamed; Poumellec, Bertrand; Lancry, Matthieu; Ibarra, Angel

2015-01-01

The aim of the present paper is to report the effect of radiation on the Er 3+ -doped sol-gel silica glasses. A possible application of these sol-gel glasses could be their use in harsh radiation environments. The sol-gel glasses are fabricated by densification of erbium salt-soaked nanoporous silica xerogels through polymeric sol-gel technique. The radiation-induced attenuation of Er 3+ -doped sol-gel silica is found to increase with erbium content. Electron paramagnetic resonance studies reveal the presence of E′ δ point defects. This happens in the sol-gel aluminum-silica glass after an exposure to γ-rays (kGy) and in sol-gel silica glass after an exposure to electrons (MGy). The concentration levels of these point defects are much lower in γ-ray irradiated sol-gel silica glasses. When the samples are co-doped with Al, the exposure to γ-ray radiation causes a possible reduction of the erbium valence from Er 3+ to Er 2+ ions. This process occurs in association with the formation of aluminum oxygen hole centers and different intrinsic point defects

Efectos del cumplimiento del Ramadán durante el embarazo sobre el peso al nacer con datos de África

OpenAIRE

Cantet, María Natalia

2014-01-01

El peso al nacer es una de las medidas más utilizada como proxy de la salud y bienestar infantil en la literatura económica. Aquellos niños con bajo peso al nacer (LBW), convencionalmente definido como menos de 2500 gramos, suelen experimentar efectos severos sobre la salud, la mortalidad, la morbilidad y la discapacidad. Por otro lado, el bajo peso al nacer también se traduce en costos sustanciales en el sector de la salud e impone una carga significativa sobre la sociedad en su conjunto. El...

El "yo" de la detective: Dolores Redondo y Carolina Solé

Directory of Open Access Journals (Sweden)

Melissa M. Culver

2015-10-01

Full Text Available Las últimas narrativas policiacas españolas escritas por mujeres, tales como El guardián invisible (Redondo, 2013 y Ojos de hielo (Solé, 2013, se caracterizan por la fuerte presencia e incluso capital importancia de la subjetividad investigadora en la resolución del crimen. En este artículo se plantea, de un lado, el hecho de que esta subjetividad de la detective se configura a partir de su oposición al carácter cientificista de la realidad actual en la investigación policiaca —basada en el cotejo de muestras de ADN y dominada por la figura de los perfiladores— y se analiza, de otro, esta oposición como radical contradicción que da lugar a una narrativa policiaca “otra” en la que, frente a la tradición del género negro clásico, se privilegia la vida sobre la muerte.

Innovative Formulation Combining Al, Zr and Si Precursors to Obtain Anticorrosion Hybrid Sol-Gel Coating

Directory of Open Access Journals (Sweden)

Clément Genet

2018-05-01

Full Text Available The aim of our study is to improve the aluminium alloy corrosion resistance with Organic-Inorganic Hybrid (OIH sol-gel coating. Coatings are obtained from unusual formulation with precursors mixing: glycidoxypropyltrimethoxysilane (GPTMS, zirconium (IV propoxide (TPOZ and aluminium tri-sec-butoxide (ASB. This formulation was characterized and compared with sol formulations GPTMS/TPOZ and GPTMS/ASB. In each formulation, a corrosion inhibitor, cerium (III nitrate hexahydrate, is employed to improve the corrosion performance. Coatings obtained from sol based on GPTMS/TPOZ/ASB have good anti-corrosion performances with Natural Salt Spray (NSS resistance of 500 h for a thickness lower than 4 µm. Contact angle measurement showed a coating hydrophobic behaviour. To understand these performances, nuclear magnetic resonance (NMR analyses were performed, results make sol-gel coating condensation evident and are in very good agreement with previous results.

Innovative Formulation Combining Al, Zr and Si Precursors to Obtain Anticorrosion Hybrid Sol-Gel Coating.

Science.gov (United States)

Genet, Clément; Menu, Marie-Joëlle; Gavard, Olivier; Ansart, Florence; Gressier, Marie; Montpellaz, Robin

2018-05-10

The aim of our study is to improve the aluminium alloy corrosion resistance with Organic-Inorganic Hybrid (OIH) sol-gel coating. Coatings are obtained from unusual formulation with precursors mixing: glycidoxypropyltrimethoxysilane (GPTMS), zirconium (IV) propoxide (TPOZ) and aluminium tri-sec-butoxide (ASB). This formulation was characterized and compared with sol formulations GPTMS/TPOZ and GPTMS/ASB. In each formulation, a corrosion inhibitor, cerium (III) nitrate hexahydrate, is employed to improve the corrosion performance. Coatings obtained from sol based on GPTMS/TPOZ/ASB have good anti-corrosion performances with Natural Salt Spray (NSS) resistance of 500 h for a thickness lower than 4 µm. Contact angle measurement showed a coating hydrophobic behaviour. To understand these performances, nuclear magnetic resonance (NMR) analyses were performed, results make sol-gel coating condensation evident and are in very good agreement with previous results.

Reversible sol-gel-sol medium for enzymatic optical biosensors

NARCIS (Netherlands)

Safaryan, S.; Yakovlev, A.; Pidko, E.A.; Vinogradov, A.; Vinogradov, V.

2017-01-01

In this paper we for the first time report a reversible sol-gel-sol approach to obtain optical enzymatic biosensors with improved enzyme stability and good sensitivity by using desktop inkjet printing. The developed technique is based on the bio-inorganic inks allowing for a sol-gel-sol transition

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

Science.gov (United States)

Hu, Weida; Wan, Long; Liu, Xiaopan; Li, Qiang; Wang, Zhiqi

2011-04-01

The diamond abrasive particles were coated with the TiO2/Al2O3 film by the sol-gel technique. Compared with the uncoated diamonds, the TiO2/Al2O3 film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO2/Al2O3 film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO2/Al2O3 film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2HRC to 66.5HRC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.

Alumina support prodn. with active component by sol-gel method - and use esp. for regenerative absorption of sulphur dioxide, oxygen or hydrogen sulphide

NARCIS (Netherlands)

Frens, G.

1991-01-01

Prodn. of a support contg. Al2O3 with an active component and/or precursor for this is carried out by the sol/gel technique by (a) producing a sol from AlCl3 or material forming Al2O3, (b) supplying the sol to the top of a column filled with a water-immiscible solvent (I) in the upper pt. and an

Vulnerabilidad social, institucionalidad y percepciones sobre el cambio climático: un acercamiento al municipio de San Felipe, Costa de Yucatán

Directory of Open Access Journals (Sweden)

Denise Soares

2011-01-01

Full Text Available Se contribuye al avance de la discusión sobre vulnerabilidad social frente al cambio climático y a la par se presenta un estudio de caso sobre percepciones acerca de la vulnerabilidad social en el municipio de San Felipe, en la costa de Yucatán, Méx., a fin de conocer, de modo contextualizado y empírico, las distintas expresiones de vulnerabilidad social que padecen los también distintos actores sociales locales. Los resultados encontrados revelan que la idea general sobre el cambio climático lo asocian principalmente al cambio de la temperatura, que un elevado porcentaje de personas jamás ha recibido capacitación sobre cambio climático y que los actores locales apuntan a los programas de empleo temporal como su principal medida de adaptación. Los resultados son preocupantes, dado que expresan un desconocimiento sobre el tema y la carencia de estrategias encaminadas a reducir la vulnerabilidad a largo plazo.

SOL: INNOVACIÓN ON-LINE

Directory of Open Access Journals (Sweden)

Rubén Faúndez

2007-11-01

Full Text Available Las aplicaciones de simulación tienden a ser cada vez más cercanas a usuarios e industrias. Sin embargo, muchas de ellas no poseen ni la capacidad ni el conocimiento como para desarrollar internamente sus modelos de simulación. Por este motivo, y como una forma de apoyar la toma de decisiones basándose en modelos de simulación, se presenta la plataforma SOL (Simulación On Line. La metodología completa de trabajo, así como la interacción entre SOL, Empresa y Asesor, son presentadas. Su base de datos, los niveles de usuarios, sus funcionalidades, y la creación automatizada de información grafica y visual, también son explicadas. En el caso de aplicación, el uso de SOL para apoyar la toma de decisiones en una operación de movimiento de material, permite a los tomadores de decisión acceder a análisis robustos basados en información extraída de los modelos de simulación. SOL, al almacenar información, funcionar vía web, generar análisis automatizados y crear visualizaciones, permite cumplir con las expectativas de los usuarios respecto a una solución integral en simulación.

Conocimientos y creencias sobre el cuidado al usuario de alcohol por estudiantes de enfermería

Directory of Open Access Journals (Sweden)

Yadira Mateo Crisóstomo

2016-07-01

Full Text Available Introducción: El aumento progresivo del consumo de alcohol, justifica la presencia de usuarios en las unidades de atención primaria, clínicas, quirúrgicas. Debido a esto la prevención del consumo de alcohol es una prioridad para enfermería debido a sus funciones como responsable del cuidado, por tal motivo el objetivo del presente estudio fue identificar los conocimientos y creencias sobre el cuidado brindado al usuario de alcohol en los estudiantes de enfermería de nivel técnico de una escuela privada. Materiales y Métodos: Estudio descriptivo correlacional de corte transversal. El tamaño de la muestra total fue de 283 estudiantes. Se utilizó el instrumento de Escala de Educación de Enfermería en Alcoholpara la evaluación de los conocimientos y creencias. Resultados y Discusión: El sexo femenino predominó con un 51.2% (x= 17,22; DE= 1,53 y la mayor proporción de estudiantes fueron de primer semestre con un (35.3%. Asimismo los estudiantes de enfermería de nivel técnico presentan un conocimiento regular y creencias positivas sobre el cuidado brindado al usuario de alcohol y se encontró una relación positiva y significativa entre los conocimientos y las creencias sobre el cuidado (rs=.408, p<.01. Conclusiones: Un conocimiento inadecuado y creencias negativas de los profesionales de enfermería hacia los usuarios que consumen alcohol pueden ser factores que interfieran en la planeación del cuidado, diagnóstico e implementación de las intervenciones de enfermería, ya que al no tener los conocimientos adecuados puede generar en el estudiante una falta de seguridad y confianza en el abordaje del cuidado al usuario de alcohol. Cómo citar este artículo: Crisóstomo YM, Armendáriz NA, Alonso MT, Martínez R. Conocimientos y creencias sobre el cuidado al usuario de alcohol por estudiantes de enfermería. Rev Cuid. 2016; 7(2: 1255-61. http://dx.doi.org/10.15649/cuidarte.v7i2.314

Effect of hydrothermal process for inorganic alumina sol on crystal structure of alumina gel

Directory of Open Access Journals (Sweden)

K. Yamamura

2016-09-01

Full Text Available This paper reports the effect of a hydrothermal process for alumina sol on the crystal structure of alumina gel derived from hydrothermally treated alumina sol to help push forward the development of low temperature synthesis of α-Al2O3. White precipitate of aluminum hydroxide was prepared with a homogeneous precipitation method using aluminum nitrate and urea in aqueous solution. The obtained aluminum hydroxide precipitate was peptized by using acetic acid at room temperature, which resulted in the production of a transparent alumina sol. The alumina sol was treated with a hydrothermal process and transformed into an alumina gel film by drying at room temperature. Crystallization of the alumina gel to α-Al2O3 with 900 °C annealing was dominant for a hydrothermal temperature of 100 °C and a hydrothermal time of 60 min, as production of diaspore-like species was promoted with the hydrothermal temperature and time. Excess treatments with hydrothermal processes at higher hydrothermal temperature for longer hydrothermal time prevented the alumina gel from being crystallized to α-Al2O3 because the excess hydrothermal treatments promoted production of boehmite.

Julgamento da Terra Indígena Raposa Serra do Sol: todo dia era dia de índio Raposa Serra do Sol Indigenous Land trial

Directory of Open Access Journals (Sweden)

Erica Magami Yamada

2010-06-01

Full Text Available O julgamento da demarcação da Terra Indígena Raposa Serra do Sol expôs o papel do STF como legislador positivo. O recém-publicado acórdão do STF sobre o caso agrega as chamadas salvaguardas institucionais formuladas nas 19 ressalvas à ação do poder executivo e aos direitos dos povos indígenas apresentadas em plenária. Algumas dessas ressalvas, verdadeiros enunciados normativos, ameaçam retroceder o reconhecimento de direitos de minorias étnicas no país, na contramão de compromissos internacionais de direitos humanos assumidos, especialmente quanto à interpretação do direito originário dos índios sobre suas terras tradicionais e quanto ao não reconhecimento da organização política indígena com o controle sobre suas terras.The trial to demarcate the Indigenous Land Raposa Serra do Sol revealed the role of the STF as a positive legislator. The recently published decision on the case incorporated the so called institutional safeguards introduced by the 19 conditions to the executive action and to indigenous peoples rights as presented during the hearings. Some of these safeguards, actual normative statements, threaten to move backwards the recognition of minority ethnic groups in brazil. They go against the international commitments of the state towards human rights, particularly regarding the interpretation of indigenous peopels original right to lands and the non-recognition of the indigenous political organization a capacity to control their own lands.

Superhydrophobic properties induced by sol-gel routes on copper surfaces

Science.gov (United States)

Raimondo, M.; Veronesi, F.; Boveri, G.; Guarini, G.; Motta, A.; Zanoni, R.

2017-11-01

Superhydrophobic surfaces are attracting increasing attention in different fields such as energy, transportation, building industry and electronics, as they exhibit many interesting properties such as high water repellence, anti-fogging, anti-corrosion, anti-fouling and self-cleaning abilities. Here, superhydrophobic nanostructured hybrid materials obtained by depositing alumina nanoparticles on copper surfaces via dip coating in Al2O3 sol are presented. Two different preparation routes were explored, based on either an alcoholic or an aqueous Al2O3 sol, and the resulting wetting properties were compared. Wettability measurements showed that when the alcoholic sol is used superhydrophobicity is attained, with values of water contact angle very close to the upper limit of 180°, while highly hydrophobic coatings are obtained with the aqueous sol. These findings were further supported by electron microscopy and X-ray photoelectron spectroscopy, which revealed that the surface layer deposited on Cu is more homogenous and richer in alumina nanoparticles when the alcoholic sol was used. Durability of the superhydrophobic coating was assessed by performing ageing tests in chemically aggressive environments. A remarkable resistance is displayed by the superhydrophobic coating in acid environment, while alkaline conditions severely affect its properties. Such behaviors were investigated by XPS and FE-SEM measurements, which disclosed the nature of the surface reactions under the different conditions tested. The present results underline that a thorough investigation of surface morphology, chemical composition and wetting properties reveals their strongly connection and helps optimizing the combination of substrate nanostructuring and suitable chemical coating for an improved durability in different aggressive environments.

sol y playa: el caso de Tenerife

Directory of Open Access Journals (Sweden)

Ricardo J. Díaz Armas

2008-01-01

Full Text Available El turismo del vino tiene una concepción distinta en un destino masivo de sol y playa. En este caso el enoturismo convive con ese modelo turístico y es un producto complementario que favorece la diversificación en la oferta actual. El turismo del vino puede complementar la ya existente oferta turística, con lo que las regiones, turísticas y a la vez viníferas, podrían apoyarse en las experiencias y conocimiento del vino por parte del visitante y utilizarlas como hecho diferencial competitivo frente a otros destinos de sol y playa que no poseen esta particularidad. Con ello además se favorecerá el lanzamiento del producto turístico del vino, pues la demanda latente ya esta en las zonas turísticas que rodean el área vinícola. En este sentido, una vez que se descubren las motivaciones para acudir al destino Tenerife, se localiza un mercado sensible a la ruta del vino Tacoronte-Acentejo en el asentamiento turístico del Puerto de la Cruz (una de las principales zonas turísticas de Tenerife. Así, tras conocer los beneficios buscados por el visitante del Puerto de la Cruz, se ha contrastado la existencia de dos segmentos latentes que pueden ser atraídos hacia la oferta actual de la ruta del vino en Tacoronte-Acentejo, al verificar que persiguen, además del clima y el sol y playa (principales motivaciones para viajar al destino Tenerife, otros beneficios que son susceptibles de ser ofertados por la ruta del vino.

Periodismo y moral - Una aproximación al discurso de prensa sobre el narcotráfico en Colombia

Directory of Open Access Journals (Sweden)

Dra. Catalina González Quintero

1998-01-01

Full Text Available Colombia es un país violento: este estereotipo, generalizado tanto entre los colombianos como en otros países del mundo, encuentra parte de su razón de ser en el predominio de la temática violenta ligada al narcotráfico cuando se tratan noticias sobre Colombia en la prensa extranjera. Para adentramos al estudio de este estereotipo, tendremos en cuenta, primero, algunas consideraciones generales sobre la representación mediática de la violencia, y segundo, los resultados un análisis las noticias sobre Colombia aparecidas en el diario El País, de España. Este análisis hizo parte de la investigación -tendiente a tesis doctoral- que realicé recientemente sobre el cubrimiento de Colombia en la prensa extranjera. El periódico El País, de España, fue escogido para realizar el estudio, dada su importancia en el contexto europeo, pues se trata del diario de habla hispana más importante de dicho continente. La muestra observada corresponde a las noticias sobre Colombia aparecidas en El País durante 1988 y 1989, tiempo en el que se desarrolló en Colombia el 'narcoterrorismo', enfrentamiento entre el llamado cartel de Medellín y el gobierno Colombiano, que dejó muchas víctimas en la población civil.

Texto e imagen en España de sol a sol de Alfonso Armada

Directory of Open Access Journals (Sweden)

Champeau, Geneviève

2011-06-01

Full Text Available España de sol a sol (2001 by Alfonso Armada gives an example of the development of the «travel narrative» genre in Spain today. Faced with the «end of travel» (Marc Augé, he proposes a renovation of the perception of the familiar by travelling across Spain and Portugal and by substituting «endotic» (Georges Pérec for exotic.The poetics in the narrative differs greatly from that by travelling writers of «social realism», in the Spain of the sixties. Interpretation replaces information, the poetic image prevails over the referential function of language, and polysemy, omnipresent intertexuality and metatextuality play an important part. The change also affects the links between text and image, which are now more complementary than redundant. Playing with stereotypes, the photography actively contributes to establishing argumentative strategies meant to make the reader-viewer adhere to the message, all while affirming itself as an autonomous aesthetic experience.España de sol a sol (2001 de Alfonso Armada proporciona una muestra de la evolución del género del «libro de viajes» en la España contemporánea. Ante la imposibilidad del viaje (Marc Augé, propone renovar la percepción de lo familiar recorriendo el espacio nacional y sustituyendo el «endotismo» (Georges Pérec al exotismo. La poética del viaje que propone el relato difiere profundamente de la de los escritores viajeros del «realismo social», en la España de los años sesenta, anteponiendo la interpretación a la información, la imagen poética a la función referencial del lenguaje, cultivando la polisemia, una intertextualidad masiva y una reflexión metatextual. Distintos son también los vínculos que se establecen entre texto e imagen, de complementariedad más que de redundancia. La fotografía participa activamente, por la reelaboración de tópicos, del dispositivo argumentativo destinado a favorecer la adhesión del lector-espectador al mensaje y se afirma

Mullite evolution in ceramics derived from clay, and sol-gel precursors

International Nuclear Information System (INIS)

Rezaie, H.R.; Naghizadeh, R.; Golestani-Fard, F.

2002-01-01

Mullite formation from sol-gel (behemoth and colloidal silica), and clay has been compared and the microstructural evolution examined using electron-optical techniques and XRD. The relationship between processing route and reaction sequence to form mullite is discussed. In sol-gel processing γAloof transforms to γ-Al 2 O 3 at 400-500 d eg w ithout an isothermal hold. δ-Al 2 O 3 was present after cooling directly from 1100 d eg i n air.(δ+θ)Al 2 O 3 were present above 1200 d eg . Reaction between (δ+θ)Al 2 O 3 and amorphous silica produced 3:2 mullite at∼ 1370 d eg . In kaolin, meta kaolin transforms to spinel and mullite at 980-1000 d eg w ithout an isothermal hold. Melanostatin to 3:2 mullite took place at 1200-1250 d eg . Cristobalite was observed after quenching from 1200 d eg , but could not be detected after cooling directly from 1590 d eg

Influence of annealing temperature on optical properties of Al doped ZnO nanoparticles via sol-gel methods

Science.gov (United States)

Rashid, Affa Rozana Abd; Hazwani, Tuan Nur; Mukhtar, Wan Maisarah; Taib, Nur Athirah Mohd

2018-06-01

Zinc oxide (ZnO) thin films have become technologically important materials due to their wide range of electrical and optical properties. The characteristics can be further adjusted by adequate doping processes. The effect of dopant concentration of Al, heating treatment and annealing in reducing atmosphere on the optical properties of the thin films is discussed. Undoped and aluminum-doped zinc oxide (AZO) thin films are prepared by the sol-gel method. Zinc acetate dihydrate, 2-methoxyethanol and monoethanolamine are used as precursor, solvent and stabilizer. In the case of AZO, aluminum nitrate nanohydrate is added to the precursor solution with an atomic percentage equal to 0 %, 1 %, 2 % and 3 % of Al. The multi thin layers are transformed into ZnO upon annealing at 450 °C and 500 °C. The optical properties such as transmittance, absorbance, band gap and refractive index of the thin films have been investigated by using UV-Visible Spectroscopy (UV-Vis). The results show that the effect of aluminium dopant concentration on the optical properties is depend on the post-heat treatment of the films. By doping with Al, the transmittance spectra in visible range increased and widen the band gap of ZnO which might due to Burstein-moss effects.

Recubrimientos de hidroxiapatita preparados mediante un proceso sol-gel

Directory of Open Access Journals (Sweden)

Peón, E.

2005-12-01

Full Text Available Hydroxyapatite coatings (HAp have been obtained starting from precursors of sol-gel type. The coatings previously oxidized were deposited on metal surfaces of a based on iron alloy so-called MA956. The alloys were at high temperatures, in order to improve the adhesion with the hydroxyapatite coatings. The sol-gel coating was obtained applying an aqueous route, using triethyl phosphite and aqueous calcium nitrate, as precursors of phosphorous and calcium, respectively. Different sintering thermal treatments were applied on the resulting gels in order to obtain a homogeneous, adherent and crystalline hydroxyapatite coating. The characterization techniques used for this study were optical microscopy, SEM/EDX, XDR and FTIR. Moreover, the adhesion between the hydroxylapatite coating and the substrate was assessed according to the ASTM D 3359-02 standard test method. The results of this study showed that the best thermal treatment is obtained for a sintering temperature of 550 °C during a time of 72 h.

Se han preparado nuevos recubrimientos de hidroxiapatita (HAp obtenidos a partir de precursores de tipo sol-gel, depositados sobre sustratos metálicos de una aleación de base hierro denominada MA956, previamente oxidados a elevadas temperaturas, para mejorar la adherencia con los recubrimientos de hidroxiapatita. El recubrimiento sol-gel se obtuvo aplicando una ruta acuosa, utilizando como precursores del fósforo y del calcio trietilfosfito y nitrato cálcico tetrahidratado, respectivamente. Sobre los geles resultantes se aplicaron distintos tratamientos térmicos de sinterización, hasta la obtención de recubrimientos de hidroxiapatita homogéneos, adherentes y cristalinos. Las técnicas de caracterización utilizadas para realizar este estudio han sido microscopía óptica, MBE/EDX, DRX y FTIR. Así mismo, se ha determinado la adherencia entre el substrato y el recubrimiento de hidroxiapatita según la norma ASTM D 3359-02. Los resultados

El cancer de piel y el sol: la protección como alternativa

OpenAIRE

Ochoa, María Teresa; Fundación Valle de Lili; Rueda Plata, Ricardo A.

1996-01-01

¿Qué es la radiación ultravioleta?/¿Qué factores afectan la cantidad de radiación UV que alcanza la tierra?/¿Qué efectos produce el sol sobre la piel? Quemadura solar aguda/Bronceamiento/Envejecimiento/Cáncer/¿Existen varios tipos de cáncer de piel?/¿Cómo se sospecha el melanoma de piel?/¿Cómo se diagnostica el cáncer de piel?/¿Cómo trata el cáncer de piel?/¿Cómo se puede detectar a tiempo?/¿Cómo se puede proteger del sol y no correr riesgos?/¿Qué es un protector solar?/¿Cómo elegir un buen p...

Puesto remisión de V. sol puesto a sol puesto, de.

OpenAIRE

2011-01-01

[ES] Definición del término Puesto remisión de V. sol puesto a sol puesto, de. en el diccionario Dicter. [EN] Definition of the word Puesto remisión de V. sol puesto a sol puesto, de. in the dictionary Dicter.

Resistencia a la oxidación de aleaciones Ni-Cr-Al plaqueadas por láser sobre aceros al carbono e inoxidables austeníticos

Directory of Open Access Journals (Sweden)

de Damborenea, J.

1995-04-01

Full Text Available Laser surface cladding has been carried out by means of a 5 kW CO₂ continuous wave laser on both a mild and a stainless steel. A powder injection technique has been used to deliver a Ni-Cr-Al alloy onto the steel molten pool. After processing, samples were analyzed by optical and scanning electron microscopy in order to know the microstructure and composition of present phases. High temperature corrosion resistance tests were done in an oxidant environment at temperatures of 950 °C. Phase transformations and corrosion behaviour are discussed. A general conclusion is the suitability of these alloys to bear oxidation due to the formation of protective oxide layers on their surface.

Se realiza un estudio sobre la obtención de recubrimientos de superficie mediante un láser continuo de CO₂ de 5 kW de potencia de salida. Mediante la técnica de inyección de partículas, se realizaron plaqueados en superficie de Ni-Cr-Al sobre un acero suave y otro inoxidable de tipo 316. Tras el procesado, se estudió la microestructura de las probetas obtenidas. Posteriormente, se procedió a su ensayo en atmósfera oxidante a 950 °C, observándose la evolución de la microestructura, la formación de las capas de óxido y la cinética del proceso. Como conclusión general, destaca, independientemente de la base sobre la que se obtienen los recubrimientos, la gran resistencia del material a la oxidación, seguramente debida a la formación de capas de alúmina que actúan como barreras frente al ataque del oxidante.

INKJET PRINTING OF ALUMOOXIDE SOL FOR DEPOSITION OF ANTIREFLECTING COATINGS

Directory of Open Access Journals (Sweden)

E. A. Eremeeva

2017-01-01

Full Text Available Subject of Research. This work describes for the first time the formation of antireflective coating on the base of boehmite phase of AlOOH with low refractive index (1.35 by inkjet printing on the nonporous substrate. This method gives the possibility to increase the contrast of colorful interfering images by 32% obtaining by inkjet printing of titanium dioxide sol. The usage of this technology enables to obtain patterns with wide viewing angle and makes them highly stable. Methods. Traditional sol-gel method with peptizing agents and heating for 90oC was applied for sol synthesis. Then the mixture was under sonic treatment for the obtaining of viscous sol. The viscosity was determined by Brookfield HA/HB viscometer, and the surface tension by Kyowa DY-700 tensiometer. Aluminum oxide ink was deposited on polished slides (26×76 mm2, Paul Marienfeld, Germany, over titanium oxide layer. To print titania ink, we use a desktop office printer Canon Pixma IP 2840 and Dimatix DMP-2831. The thickness of an inkjet AlOOH layer after drying in the air and removal of the solvents did not exceed 150 nm with an RI not less than 1.35 in the entire visible range. Results. The stable colloidal ink was obtained for the first time on the base of aluminum oxide matrix with neutral pH. The rheology was regulated by controlling parameters of sol-gel method in the system of aqueous titanium dioxide sol and by adding ethanol that affects the charge of double electrical layer of disperse phase. The controllable coalesce of drops enables to apply antireflection coating within the thickness accuracy of 10 nm. The morphology of particles and the topology of printed structures were analyzed by optical, scanning electron and atomic-force microscopes. Practical Relevance. We have proposed the approach to obtain colorful, interference patterns using two types of high refractive inks with different refractive indexes. The inkjet printing method opens new opportunities for

Sol-gel-cum-hydrothermal synthesis of mesoporous Co-Fe@Al2O3 ...

Indian Academy of Sciences (India)

Oxides; sol-gel; adsorption; surface properties; composite materials. 1. Introduction. Industrial dyes ... acid green 25, Congo red, N719), phenolic compounds. (bromophenol blue .... microscopy (TEM) images were obtained using Philips CM.

The structural studies of aluminosilicate gels and thin films synthesized by the sol-gel method using different Al2O3 and SiO2 precursors

Directory of Open Access Journals (Sweden)

Adamczyk Anna

2015-12-01

Full Text Available Aluminosilicate materials were obtained by sol-gel method, using different Al2O3 and SiO2 precursors in order to prepare sols based on water and organic solvents. As SiO2 precursors, Aerosil 200TM and tetraethoxysilane TEOS: Si(OC2H54 were applied, while DisperalTM and aluminium secondary butoxide ATSB: Al(OC4H93 were used for Al2O3 ones. Bulk samples were obtained by heating gels at 500 °C, 850 °C and at 1150 °C in air, while thin films were synthesized on carbon, steel and alundum (representing porous ceramics substrates by the dip coating method. Thin films were annealed in air (steel and alundum and in argon (carbon at different temperatures, depending on the substrate type. The samples were synthesized as gels and coatings of the composition corresponding the that of 3Al2O3·2SiO2 mullite because of the specific valuable properties of this material. The structure of the annealed bulk samples and coatings was studied by FT-IR spectroscopy and XRD method (in standard and GID configurations. Additionally, the electron microscopy (SEM together with EDS microanalysis were applied to describe the morphology and the chemical composition of thin films. The analysis of FT-IR spectra and X-ray diffraction patterns of bulk samples revealed the presence of γ-Al2O3 and δ-Al2O3 phases, together with the small amount of SiO2 in the particulate samples. This observation was confirmed by the bands due to vibrations of Al–O bonds occurring in γ-Al2O3 and δ-Al2O3 structures, in the range of 400 to 900 cm−1. The same phases (γ-Al2O3 and δ-Al2O were observed in the deposited coatings, but the presence of particulate ones strongly depended on the type of Al2O3 and SiO2 precursor and on the heat treatment temperature. All thin films contained considerable amounts of amorphous phase.

Efecto antifúngico de hidrodestilados de Zingiber officinale Roscoe sobre Moniliophthora roreri (Cif&Par

Directory of Open Access Journals (Sweden)

José Gregorio Joya-Dávila

2015-07-01

Full Text Available La moniliasis, ocasionada por el hongo Moniliophthora roreri (Cif. & Par, es la principal enfermedad del cacao en Latinoamérica, y las medidas para su manejo sostenible son aún escasas. Con base en reportes previos, el objetivo de este trabajo fue optimizar el proceso de extracción por destilación de Zingiber officinale, evaluando in vitro su efecto antifúngico sobre conidias de M. roreri. Se elaboraron ocho hidrodestilados con material fresco (300 y 600 g/L y seco al sol (45 y 90 g/L, con dos solventes (agua-alcohol, relación 10:1 y 10:0, y en tubos de ensayo con conidias del hongo, mediante la técnica de cultivo en medio líquido (agua-extracto de cacao, se adicionó cada hidrodestilado de Z. officinale en relación 1:1 v/v, determinando su efecto sobre la formación y germinación de conidias del hongo en cinco momentos de observación (0, 24, 48, 72 y 96 horas. Los resultados muestran que todos los hidrodestilados de Z. officinale presentan metabolitos con efectos de inhibición sobre las variables evaluadas, siendo el tratamiento J5 (Z. officinale seco, 45 g/L, relación 10:1 agua: alcohol el mejor, pues alcanza el 88% y el 100% de control sobre la formación y germinación de conidias, respectivamente, con respecto al testigo absoluto a las 72 horas, siendo posible optimizar la extracción mediante destilación utilizando 45 g/L de material seco y el uso de solvente agua-alcohol en una relación 10:1.

Biocompatibility and Corrosion Protection Behaviour of Hydroxyapatite Sol-Gel-Derived Coatings on Ti6Al4V Alloy

Science.gov (United States)

El Hadad, Amir A.; Peón, Eduardo; García-Galván, Federico R.; Barranco, Violeta; Parra, Juan; Jiménez-Morales, Antonia; Galván, Juan Carlos

2017-01-01

The aim of this work was to prepare hydroxyapatite coatings (HAp) by a sol-gel method on Ti6Al4V alloy and to study the bioactivity, biocompatibility and corrosion protection behaviour of these coatings in presence of simulated body fluids (SBFs). Thermogravimetric/Differential Thermal Analyses (TG/DTA) and X-ray Diffraction (XRD) have been applied to obtain information about the phase transformations, mass loss, identification of the phases developed, crystallite size and degree of crystallinity of the obtained HAp powders. Fourier Transformer Infrared Spectroscopy (FTIR) has been utilized for studying the functional groups of the prepared structures. The surface morphology of the resulting HAp coatings was studied by Scanning Electron Microscopy (SEM). The bioactivity was evaluated by soaking the HAp-coatings/Ti6Al4V system in Kokubo’s Simulated Body Fluid (SBF) applying Inductively Coupled Plasma (ICP) spectrometry. 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl tetrazolium bromide (MTT) and Alamar blue cell viability assays were used to study the biocompatibility. Finally, the corrosion behaviour of HAp-coatings/Ti6Al4V system was researched by means of Electrochemical Impedance Spectroscopy (EIS). The obtained results showed that the prepared powders were nanocrystalline HAp with little deviations from that present in the human bone. All the prepared HAp coatings deposited on Ti6Al4V showed well-behaved biocompatibility, good bioactivity and corrosion protection properties. PMID:28772455

Biocompatibility and Corrosion Protection Behaviour of Hydroxyapatite Sol-Gel-Derived Coatings on Ti6Al4V Alloy

Directory of Open Access Journals (Sweden)

Amir A. El Hadad

2017-01-01

Full Text Available The aim of this work was to prepare hydroxyapatite coatings (HAp by a sol-gel method on Ti6Al4V alloy and to study the bioactivity, biocompatibility and corrosion protection behaviour of these coatings in presence of simulated body fluids (SBFs. Thermogravimetric/Differential Thermal Analyses (TG/DTA and X-ray Diffraction (XRD have been applied to obtain information about the phase transformations, mass loss, identification of the phases developed, crystallite size and degree of crystallinity of the obtained HAp powders. Fourier Transformer Infrared Spectroscopy (FTIR has been utilized for studying the functional groups of the prepared structures. The surface morphology of the resulting HAp coatings was studied by Scanning Electron Microscopy (SEM. The bioactivity was evaluated by soaking the HAp-coatings/Ti6Al4V system in Kokubo’s Simulated Body Fluid (SBF applying Inductively Coupled Plasma (ICP spectrometry. 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl tetrazolium bromide (MTT and Alamar blue cell viability assays were used to study the biocompatibility. Finally, the corrosion behaviour of HAp-coatings/Ti6Al4V system was researched by means of Electrochemical Impedance Spectroscopy (EIS. The obtained results showed that the prepared powders were nanocrystalline HAp with little deviations from that present in the human bone. All the prepared HAp coatings deposited on Ti6Al4V showed well-behaved biocompatibility, good bioactivity and corrosion protection properties.

Apuntes sobre el Cultivo del Cacao

Directory of Open Access Journals (Sweden)

Chavarriaga. Eduardo

1940-09-01

Full Text Available El sombrío constituye uno de los problemas que se presentan en el cultivo del cacao, de necesaria resolución para ayuda del agricultor en su labor al producir tan importante grano. Contribuye a la economía del cultivo un conocimiento amplio de la cuestión que debe preocupar al productor inquiriendo no solamente por lo acostumbrado en la región, sino por lo que en otras partes se conoce sobre el particular, para abandonar un poco el emperismo y hacer una industria cada día más próspera. Como razón a favor del sombrío, tenemos los países en donde se produce cacao de fina calidad; Trinidad, Venezuela. Nicaragua, siempre acostumbran la sombra; y sin ir muy lejos, en el Valle del Cauca, donde no se cultiva a pleno sol y se obtienen plantaciones de larga duración y producto superior, es bien conocido el beneficio de ella; allí, los agricultores conocen los desastrosos efectos que ocasiona la falta de sombra, cuando por cualquier causa mueren los árboles que la suministran. Por tanto, en este estudio indicaremos el uso de la sombra para el cacao, como el medio de conservar la fertilidad y buenas condiciones del suelo, obtener buenos rendimientos y asegurar larga vida a la plantación.

Effect of the Mg/Al Ratio on Activated Sol-Gel Hydrotalcites for Photocatalytic Degradation of 2,4,6-Trichlorophenol

Directory of Open Access Journals (Sweden)

Esthela Ramos-Ramírez

2017-01-01

Full Text Available Currently, interest has grown in finding effective solutions for the treatment of water pollution by toxic compounds. Some of the latter that have acquired importance are phenols and chlorophenols, due to their employment in the manufacture of pesticides, insecticides, cords of wood, paper industry, among others. The problem is rooted in that these compounds are very persistent in the environment because they are partially biodegradable and cannot be photodegraded directly by sunlight. Chlorophenols are extremely toxic, especially 2,4,6-trichlorophenol, which is potentially carcinogenic. In this work, Mg/Al-mixed oxide catalysts were obtained from the thermal treatment of hydrotalcite-type materials, synthesized by sol-gel method with different Mg/Al ratios. Hydrotalcites and Mg/Al-mixed oxides were physicochemically characterized by X-ray diffraction, thermal analysis (DTA and TGA, and N2 physisorption. The results were obtained on having proven the photocatalytic degradation of 2,4,6-trichlorophenol as a pollutant model by water. The catalysts obtained present the hydrotalcite phase with thermal evolution until achieving Mg/Al-mixed oxides at 500°C. The catalysts are of mesoporous materials and exhibiting large surface areas. The catalysts demonstrated good photocatalytic activity with good efficiency, reaching degradation percentages with Mg/Al = 1, 2, 4, 5, and 7 ratios of 94.2, 92.5, 86.2, 84.2, and 63.9%, respectively, until achieving mineralization.

Recubrimientos metálicos sobre alúmina mediante procesos de reducción autocatalítica

Directory of Open Access Journals (Sweden)

Gómez de Salazar, J. M.

2000-10-01

Full Text Available In this work, a method for obtaining copper coating on alumina is described. One of the main applications for this coating is in the electronic industry, although it can be used as well as interlayer for dissimilar bonding between metals and alumina, both by solid state joining and by active brazing. The optimal activation conditions for the alumina using Ni salts and the influence of the surface preparation on the copper coating characteristic are described. The coating application is based on an autocatalithic reduction method. The influence of the deposition rate on the adherence of the copper coating has been studied as well. A kinetic study was carried out applying gravimetric and electrochemical methods. To obtaining coating with high adherence, it was necessary to apply heat treatments after the metallization process. The main objective of them was to achieve a chemical bond between the alumina substrate and the copper coating by formation of Al-Cu spinels, instead of the single mechanical bond.

En el presente trabajo se describe un método de obtención de recubrimientos de cobre sobre un cerámico tenaz como es la alúmina. Una de sus principales aplicaciones se encuentra en la industria electrónica, aunque también puede ser empleado como intermediario en la fabricación de uniones disimilares entre un metal y un cerámico mediante técnicas de unión en estado sólido o en soldadura fuerte reactiva. Se describen las condiciones óptimas de activación de la alúmina mediante sales de Ni, y la influencia que posee la preparación superficial de este substrato (Al2O3 sobre las capas de Cu obtenidas. Este proceso se realiza mediante reducción autocatalítica, habiéndose estudiado como influye la velocidad de deposición sobre la adherencia de la capa de cobre. También se realizaron estudios cinéticos del proceso de recubrimiento mediante ensayos gravimétricos y electroquímicos. Con el fin de obtener recubrimientos que

Digitalización de diapositivas del Sol en H α

Science.gov (United States)

Missio, H.; Montenegro, C.; Montenegro, R.

El objetivo de este trabajo ha sido el de obtener imágenes digitalizadas de las diapositivas tomadas del Sol en luz de hidrógeno de la línea correspondiente a Hα, y de esta manera llegar a convertir las mismas a un archivo digital para poder ser tratadas luego por computadora y poder contabilizar con exactitud, mediante un programa adecuado para tal fin, las zonas activas del Sol en la imagen digitalizada. En principio, para llegar a esto se pensó en la utilización de medios accesibles, y como detector se utilizó un fototransistor ubicado dentro de un soporte rectangular sobre dos ejes de desplazamiento X e Y. Se han obtenido con este procedimiento imágenes de buena calidad, construídas a partir de tres datos digitalizados en cada barrido que aportan la posición X e Y y la intensidad del pixel en ese punto indicada en 255 tonos de grises.

Is the Dark Side of the Moon Ever Illuminated by the Sun? (Breton Title: O Lado Escuro da Lua Nunca Apanha Sol?) El Lado Oscuro de la Luna Nunca Toma Sol?

Science.gov (United States)

Giovannini, Odilon; Pellenz, Daiana; Catelli, Francisco

2014-07-01

y los elementos básicos que componen una "respuesta correcta". Estas cuestiones se tratan inicialmente a partir de una revisión bibliográfica de la investigación en el área; seguidamente, y también sobre la base de ésta revisión, se propone un modelo didáctico que ejemplifica los movimientos relativos del sistema Tierra - Luna - Sol. Se describe a continuación una aplicación de este modelo en un entorno de aprendizaje con alumnos del ciclo primario. Los conceptos iniciales presentados en la literatura se confirman y las cuestiones planteadas por los estudiantes durante la implementación del modelo proporcionan evidencia de que se ha producido un aprendizaje significativo, al menos en cierta medida.

Inferencias sobre Grafos

OpenAIRE

Sira M. Allende; Carlos N. Bouza

2002-01-01

El estudio de un juego puede ser modelado asumiendo que solo algunas partidas son observadas. Entonces el árbol del juego debe ser estimado utilizando información muestral. Similarmente ocurre al obtener información sobre el comportamiento de las decisiones tomadas por individuos muestreados sobre un árbol de decisión teórico. Al considerar una medida de probabilidad que caracterice el comportamiento de redes aleatorias se puede obtener un estimado del árbol asociado. Este problema es el anal...

Variation in Structural and Optical Properties of Al Doped ZnO Nanoparticles Synthesized by Sol-gel Process

Directory of Open Access Journals (Sweden)

Vanaja Aravapalli

2017-04-01

Full Text Available This article focuses on analyzing structural and optical properties of Al doped ZnO (AZO synthesized with two different precursors aluminum chloride and aluminum nitrate. The nanoparticles were successfully fabricated and characterized at room temperature by sol-gel process. The objective of improving properties of ZnO nanoparticles by introducing dopants was successful with formation of nanoparticles having different crystalline sizes, optical absorption and luminescence properties. The two different sources influenced properties of ZnO. The particles with less crystalline size obtained from aluminum nitrate. Change in morphology from spherical to bar like morphology proved from SEM spectra. Presence of functional groups predicted from FTIR spectra. PL spectra proved UV emission and visible emission for AZO nanoparticles synthesized using dopant sources aluminum chloride and aluminum nitrate respectively. The obtained properties prove successful utilization of AZO nanoparticles as building materials in fabrication of optoelectronic devices.

The zinc fingers of the Small Optic Lobes (SOL) calpain bind polyubiquitin.

Science.gov (United States)

Hastings, Margaret H; Qiu, Alvin; Zha, Congyao; Farah, Carole A; Mahdid, Yacine; Ferguson, Larissa; Sossin, Wayne S

2018-05-28

The Small Optic Lobes (SOL) calpain is a highly conserved member of the calpain family expressed in the nervous system. A dominant negative form of the SOL calpain inhibited consolidation of one form of synaptic plasticity, non-associative facilitation, in sensory-motor neuronal cultures in Aplysia, presumably by inhibiting cleavage of protein kinase Cs (PKCs) into constitutively active protein kinase Ms (PKMs) (Hu et al, 2017a). SOL calpains have a conserved set of 5-6 N-terminal zinc fingers. Bioinformatic analysis suggests that these zinc fingers could bind to ubiquitin. In this study, we show that both the Aplysia and mouse SOL calpain (also known as Calpain 15) zinc fingers bind ubiquitinated proteins, and we confirm that Aplysia SOL binds poly- but not mono or di-ubiquitin. No specific zinc finger is required for polyubiquitin binding. Neither polyubiquitin nor calcium was sufficient to induce purified Aplysia SOL calpain to autolyse or to cleave the atypical PKC to PKM in vitro. In Aplysia, overexpression of the atypical PKC in sensory neurons leads to an activity-dependent cleavage event and an increase in nuclear ubiquitin staining. Activity-dependent cleavage is partially blocked by a dominant negative SOL calpain, but not by a dominant negative classical calpain. The cleaved PKM was stabilized by the dominant negative classical calpain and destabilized by a dominant negative form of the PKM stabilizing proteinKIdney/BRAin protein(KIBRA). These studies provide new insight into SOL calpain's function and regulation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Hydrogen Production by Steam Reforming of Ethanol over Nickel Catalysts Supported on Sol Gel Made Alumina: Influence of Calcination Temperature on Supports.

Science.gov (United States)

Yaakob, Zahira; Bshish, Ahmed; Ebshish, Ali; Tasirin, Siti Masrinda; Alhasan, Fatah H

2013-05-30

Selecting a proper support in the catalyst system plays an important role in hydrogen production via ethanol steam reforming. In this study, sol gel made alumina supports prepared for nickel (Ni) catalysts were calcined at different temperatures. A series of (Ni/Al S.G. ) catalysts were synthesized by an impregnation procedure. The influence of varying the calcination temperature of the sol gel made supports on catalyst activity was tested in ethanol reforming reaction. The characteristics of the sol gel alumina supports and Ni catalysts were affected by the calcination temperature of the supports. The structure of the sol gel made alumina supports was transformed in the order of γ → (γ + θ) → θ-alumina as the calcination temperature of the supports increased from 600 °C to 1000 °C. Both hydrogen yield and ethanol conversion presented a volcano-shaped behavior with maximum values of 4.3 mol/mol ethanol fed and 99.5%, respectively. The optimum values were exhibited over Ni/Al S.G800 (Ni catalyst supported on sol gel made alumina calcined at 800 °C). The high performance of the Ni/Al S.G800 catalyst may be attributed to the strong interaction of Ni species and sol gel made alumina which lead to high nickel dispersion and small particle size.

Metal-silica sol-gel materials

Science.gov (United States)

Stiegman, Albert E. (Inventor)

2002-01-01

The present invention relates to a single phase metal-silica sol-gel glass formed by the co-condensation of a transition metal with silicon atoms where the metal atoms are uniformly distributed within the sol-gel glass as individual metal centers. Any transition metal may be used in the sol-gel glasses. The present invention also relates to sensor materials where the sensor material is formed using the single phase metal-silica sol-gel glasses. The sensor materials may be in the form of a thin film or may be attached to an optical fiber. The present invention also relates to a method of sensing chemicals using the chemical sensors by monitoring the chromatic change of the metal-silica sol-gel glass when the chemical binds to the sensor. The present invention also relates to oxidation catalysts where a metal-silica sol-gel glass catalyzes the reaction. The present invention also relates to a method of performing oxidation reactions using the metal-silica sol-gel glasses. The present invention also relates to organopolymer metal-silica sol-gel composites where the pores of the metal-silica sol-gel glasses are filled with an organic polymer polymerized by the sol-gel glass.

Effect of the crystallinity in the Tl signal induced by the gamma radiation in Al{sub 2}O{sub 3}: Eu obtained by the sol gel method; Efecto de la cristalinidad en la senal Tl inducida por la radiacion gamma en Al{sub 2}O{sub 3}: Eu obtenida por el metodo sol gel

Energy Technology Data Exchange (ETDEWEB)

Mendoza A, D.; Gonzalez M, P.R. [ININ, Gerencia de Ciencias de Materiales. Carr. Mexico-Toluca Km. 36.5, 52045 Ocoyoacac (Mexico); Custodio, E. [Universidad Juarez Autonoma de Tabasco, DACB, Carr. Cunduacan-Jalpa, km. 1.5, 86680 Tabasco (Mexico); Rubio, E.; Rodriguez L, V. [Facultad de Ingenieria Quimica, BUAP. Av. San Claudio y 18 Sur Col. San Manuel. C. P. 72570.C.U. Puebla (Mexico)

2004-07-01

In this work the synthesis and characterization process of Al{sub 2}O{sub 3} and Al{sub 2}O{sub 3}: Eu by sol gel method is reported. A previous thermal treatment at 500 and 1000 C on the material powder type showed a notable influences on the thermoluminescent signal induced by the gamma radiation, such that the intensity thermoluminescent signal produced by samples with thermal treatment at 1000 C is much bigger that thermoluminescent signal produced by samples thermal treatment at 500 C. In order to explain this behavior, an analysis for X-ray diffraction and electron microscopy was also realized. The results show a notably influence of the crystalline array and the microstructure on the thermoluminescent behavior of the alumina. (Author)

Thoria sol-gel processes

International Nuclear Information System (INIS)

Matthews, R.B.

1978-10-01

Alternate fuel fabrication techniques are being developed at WNRE as part of the thorium fuel cycle program. The sol-gel techniques are attractive and this report assembles and summarizes information relating to thoria sol-gel fuels. Some background information on the behaviour and advantages of sol-gel fuel forms is presented, followed by a review of relevant colloid chemistry and an explanation of the fundamental steps of sol-gel processes. Finally, several variants to the basic process are reviewed and evaluated. (author)

Estudio de la protección del refuerzo de partículas de SiC mediante barreras activas por sol-gel en materiales compuestos de matriz de aluminio

Directory of Open Access Journals (Sweden)

Ureña, A.

2004-04-01

Full Text Available A microcrystalline, homogeneous and transparent sol – gel silica coating has been developed to avoid the degradation and improve the wettability of aluminium matrix composites reinforced with SiC particles. Composite aluminium matrix samples have been made by cold powder compaction, and the coating efficiency has been checked by melting the samples several temperature and times. The coating reduces the appearance of Al4C3, showing that the degradation resistance of the new material is much higher than that of the uncovered SiC particles composite one.

Con objeto de prevenir la degradación y mejorar la mojabilidad de los materiales compuestos de matriz de aluminio reforzados con partículas de SiC se ha desarrollado un recubrimiento microcristalino, homogéneo y transparente de SiO2 obtenido por el método sol-gel. La eficacia del recubrimiento como barrera se ha comprobado realizando ensayos de fusión a diferentes tiempos y temperaturas sobre pastillas de material compuesto de matriz de aluminio obtenidas por compactación en frío de polvos. El recubrimiento limita la formación de Al4C3, lo que indica que la resistencia a la degradación del nuevo material es muy superior a la del fabricado con partículas de SiC sin recubrir.

Modificação parcial do ambiente de cultivo da videira 'Cabernet Sauvignon' sobre diferentes porta-enxertos: efeito sobre a produção e o teor de sólidos solúveis Crop partially modified environment on different rootstocks of 'Cabernet Sauvignon' grapevine: effect on yield and sugar concentration

Directory of Open Access Journals (Sweden)

Maria Aparecida Ferreira

2004-12-01

Full Text Available Nas regiões onde existe ocorrência de chuvas durante o desenvolvimento e a maturação dos frutos justifica-se a busca de alternativas de cultivo protegido de uvas para vinho visando atenuar esse impacto sobre a qualidade da produção. Um experimento com a cultivar Cabernet Sauvignon sobre os porta-enxertos 'IAC 766', 'IAC 572' e 'Ripária do Traviú',cultura videira foi conduzido em Jundiaí (SP, sob cultivo protegido (cobertura com plástico e laterais abertas, objetivando estudar as alterações microclimáticas ocorridas no ambiente de cultivo do vinhedo e avaliar o impacto dessa prática sobre a produção e o teor de sólidos solúveis, em relação ao cultivo em ambiente a céu aberto. A proteção por polietileno no cultivo da 'Cabernet Sauvignon' diminuiu o nível de radiação solar para 85,4% e aumentou as temperaturas máximas em 1,3 ºC. Nos ambientes analisados separadamente, as maiores produções por planta e teor de sólidos solúveis foram obtidas na 'Cabernet Sauvignon' sobre porta-enxertos 'IAC 766' e 'IAC 572' que superaram o 'Ripária do Traviú'. Na comparação entre os ambientes a céu aberto e parcialmente modificado não foram encontradas diferenças de produção, porém o teor de sólidos solúveis foi superior no ambiente a céu aberto.In the traditional regions of grape growers, where the incidence of rain is concentrated on the stage of fruit development and maturation, the search for improved crop management strategies is justified, aiming at attenuate the impact of it on yield quality. An experiment with grapevine "Cabernet Sauvignon" cultivated on rootstocks IAC 766, IAC 572 and Ripária do Traviú was carried out in Jundiaí, São Paulo State, Brazil, under plastic greenhouse. The search was focused on the microclimate modification in the environment of cultivated grapes from its conduction in partially modified crop cultivation environment (plastic cover with open sides, as well as evaluates the impact on

Effect of the crystallinity in the Tl signal induced by the gamma radiation in Al2O3: Eu obtained by the sol gel method

International Nuclear Information System (INIS)

Mendoza A, D.; Gonzalez M, P.R.; Custodio, E.; Rubio, E.; Rodriguez L, V.

2004-01-01

In this work the synthesis and characterization process of Al 2 O 3 and Al 2 O 3 : Eu by sol gel method is reported. A previous thermal treatment at 500 and 1000 C on the material powder type showed a notable influences on the thermoluminescent signal induced by the gamma radiation, such that the intensity thermoluminescent signal produced by samples with thermal treatment at 1000 C is much bigger that thermoluminescent signal produced by samples thermal treatment at 500 C. In order to explain this behavior, an analysis for X-ray diffraction and electron microscopy was also realized. The results show a notably influence of the crystalline array and the microstructure on the thermoluminescent behavior of the alumina. (Author)

Edad y nivel educativo asociados al conocimiento sobre signos de alarma para infecciones respiratorias en madres adolescentes

Directory of Open Access Journals (Sweden)

Regina Domínguez Anaya

2017-05-01

Full Text Available Introducción: La identificación de señales de alarma durante la Infección Respiratoria Aguda (IRA, es fundamental para disminuir el impacto de la enfermedad y la mortalidad asociada. El objetivo del estudio fue estimar la relación entre la edad y el nivel educativo al conocimiento sobre signos de alarma de IRA, en madres adolescentes. Materiales y Métodos: Estudio transversal, con una muestra aleatoria de 120 madres adolescentes adscritas a una fundación privada de la ciudad de Cartagena, a quienes se aplicó el cuestionario de Prácticas Claves sobre IRA propuesto por la Organización Panamericana de la Salud. Resultados: El promedio de edad de las participantes fue 17 ± 1.3 años. Se encontró que ser mayor de 17 años aumenta la probabilidad de reconocer por lo menos tres signos alarma [OR: 2.8 (IC 95%: 1.3 - 6.1]. Asimismo, las adolescentes con un mayor nivel de escolaridad tienen más probabilidad de reconocer tres signos de alarma para la enfermedad [OR: 3.2 (IC 95%: 1.5 - 6.9], que aquellas con menor nivel educativo. Discusión y Conclusiones: Determinantes personales como una mayor edad y escolaridad impactan de forma positiva en los conocimientos de las madres sobre los signos de alarma de IRA. Es importante el fortalecimiento de los programas de educación en salud para el cuidado de los niños entre esta población. Cómo citar este artículo: Domínguez R, Tapia E, Hernández J, Castillo IY. Edad y nivel educativo asociados al conocimiento sobre signos de alarma para infecciones respiratorias en madres adolescentes. Rev Cuid. 2017; 8(2: 1628-37. http://dx.doi.org/10.15649/cuidarte.v8i2.395

TURISMO Y CUERPOS DESNUDOS Moda y culto al sol en el litoral marítimo argentino

Directory of Open Access Journals (Sweden)

Regina Schlüter

2010-09-01

Full Text Available Normal 0 21 false false false PT-BR X-NONE X-NONE MicrosoftInternetExplorer4 Resumen: Los cambios en la estructura social que se observaron en Argentina después de la Primera Guerra Mundial le dieron a la mujer una mayor libertad de acción permitiéndole ingresar en el campo laboral, practicar deportes y participar del turismo. Esto tuvo un gran impacto en la moda de la época y modificó las formas de socialización lo que se observa en los destinos de sol y playa de la época. La vestimenta femenina que se caracterizaba por una extrema formalidad que no dejaba nada al descubierto fue dejando a la vista cada vez mayores partes del cuerpo y se comenzó a priorizar la comodidad. También la moda del bronceado jugó un rol preponderante en las costumbres de la época ya que se convirtió en un elemento importante de diferenciación social.

Preparation and characterization of sol-gel derived 4%La{sub 2}O{sub 3}-Al{sub 2}O{sub 3} ceramic membrane on clay-based supports

Energy Technology Data Exchange (ETDEWEB)

Ersoy, B. [Afyon Kocatepe Univ., Mining Engineering Dept., AFYON (Turkey); Gunay, V. [TUBITAK-MRC, MCTRI, Gebze-KOCAELI (Turkey)

2004-07-01

In this work, {gamma}-Al{sub 2}O{sub 3} membrane layer (4 wt% La{sub 2}O{sub 3}+96% Al{sub 2}O{sub 3}) was coated on the clay based porous support by using the sol-gel coating. The coating solution was prepared by using boehmite (AlOOH), La-nitrate (La{sub 2}(NO{sub 3}){sub 3}.6H{sub 2}O), PVA, distilled water and HNO{sub 3}. The thickness of the {gamma}-Al{sub 2}O{sub 3} membrane layer was between 5-7 {mu}m. Two unprocessed clay samples which were supplied from Kutahya and Balikesir regions, were used to produce supports for the membranes. Porosities of the supports were varied from 25 to 40% depending on sintering temperatures. Mean pore diameter of the supports were between 0.01-1{mu}m. The mean pore diameter of 4wt%La{sub 2}O{sub 3} - Al{sub 2}O{sub 3} membrane layer was around 11 nm and total pore area was 113 m{sup 2} / g at 1000 C for 1 hour. (orig.)

Expedition sol

DEFF Research Database (Denmark)

Jacobsen, Aase Roland

2006-01-01

Tag på expedition sol rundt i museet. Er der nogen, der har taget en bid af solen? Hvorfor bliver der solformørkelse? Kan vi undvære Solen?......Tag på expedition sol rundt i museet. Er der nogen, der har taget en bid af solen? Hvorfor bliver der solformørkelse? Kan vi undvære Solen?...

Synthesis of Copper-Based Transparent Conductive Oxides with Delafossite Structure via Sol-Gel Processing

OpenAIRE

Götzendörfer, Stefan

2011-01-01

Starting off with solubility experiments of possible precursors, the present study reveals the whole development of a sol gel processing route for transparent p type semiconductive thin films with delafossite structure right to the fabrication of functional p-n junctions. The versatile sol formulation could successfully be modified for several oxide compositions, enabling the synthesis of CuAlO2, CuCrO2, CuMnO2, CuFeO2 and more. Although several differences in the sintering behaviour of powde...

Evaluación anticorrosiva de tricapas cerámicas Sio2-Tio2-Zro2 sintetizadas por el método Sol-Gel

Directory of Open Access Journals (Sweden)

Jorge Hernando Bautista Ruiz

2009-06-01

Full Text Available  Se muestra la conformación de tricapas de recubrimientoscerámicos del sistema SiO2-TiO2-ZrO2, sintetizadas por elmétodo Sol-gel, utilizando como precursores Si(OC2H54,Ti(OBu4 y Zr(OC3H74, como solventes EtOH y agua, ycomo acomplejante 2,4 pentanodiona. Los recubrimientoscerámicos fueron depositados sobre sustratos de aceroinoxidable AISI/SAE 304 mediante la técnica de inmersión(dip-coating. Se estudió la influencia de los recubrimientossobre el comportamiento anticorrosivo del sustrato en unasolución de HCl al 3% mediante las técnicas deEspectroscopia de Impedancia Electroquímica (EIS ycurvas potenciodinámicas de polarización. Adicionalmentese realizó un estudio morfológico mediante la técnica deMicroscopía de Fuerza Atómica (AFM. Se encontró quelos valores de los parámetros electroquímicos cambiansustancialmente con la concentración de los precursoressumada a los efectos de la película sobre el sustrato.

Diseño de recubrimientos multicapa barrera-biomimético base TEOS-GPTMS sobre la aleación de magnesio Elektron 21 de potencial aplicación en la fabricación de implantes ortopédicos

Directory of Open Access Journals (Sweden)

Rueda, Laura M.

2016-09-01

Full Text Available In the present work, barrier-biomimetic multilayer coatings were synthesized via sol-gel on the commercial Elektron 21 magnesium alloy, with potential interest in the fabrication of orthopaedic temporal implants. Sol-gel synthesis was carried out from a mixture of inorganic and organic precursors, TEOS and GPTMS. Two different sols were prepared: sols employed for the design of barrier coatings (named GT which function were to protect the magnesium alloy against corrosion; and sols containing additionally calcium nitrate (named GTCa, in different concentrations, for the design of the biomimetic coatings, which were deposited over the GT coating. The results confirmed that the GT coatings enhanced the corrosion resistance of the base alloy in Hank solution, reducing the corrosion current density in about two orders of magnitude. Further, the presence of Ca(II in GTCa coatings promoted the formation of discontinuous film of hydroxyapatite on the surface, indicating that those coatings exhibit bioactive properties.En el presente estudio se sintetizaron recubrimientos híbridos multicapa barrera-biomimético vía sol-gel sobre la aleación de magnesio Elektron 21, de potencial aplicación en el diseño de implantes ortopédicos de uso temporal. Para la síntesis sol-gel se empleó mezclas de los precursores de películas inorgánicas, TEOS, orgánicas y GPTMS. Se prepararon soles para el desarrollo del recubrimiento barrera frente al proceso de corrosión (soles GT; y soles con incorporación de nitrato de calcio en diferentes concentraciones (soles GTCa, para el desarrollo de los recubrimientos biomiméticos que fueron depositados sobre el recubrimiento GT. Los resultados obtenidos revelaron que el recubrimiento GT incrementó la resistencia a la corrosión de la aleación en solución Hank, reduciendo la densidad de corriente de corrosión alrededor de dos órdenes de magnitud. Asimismo, la incorporación de Ca(II a los recubrimientos GTCa

Fabrication of silica glass containing yellow oxynitride phosphor by the sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Segawa, Hiroyo; Yoshimizu, Hisato; Hirosaki, Naoto; Inoue, Satoru, E-mail: SEGAWA.Hiroyo@nims.go.jp [National Institute for Materials Science, 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan)

2011-06-15

We have prepared silica glass by the sol-gel method and studied its ability to disperse the Ca-{alpha}-SiAlON:Eu{sup 2+} phosphor for application in white light emitting diodes (LEDs). The emission color generated by irradiating doped glass with a blue LED at 450 nm depended on the concentration of SiAlON and the glass thickness, resulting in nearly white light. The luminescence efficiency of 1-mm-thick glass depended on the SiAlON concentration, and was highest at 4 wt% SiAlON.

Sol-gel synthesis and characterization of fine-grained ceramics in the alumina-titania system

Energy Technology Data Exchange (ETDEWEB)

Otterstein, E. [Institute of Physics, University of Rostock, August-Bebel-Strasse 55, 18055 Rostock (Germany)], E-mail: otterstein@physik1.uni-rostock.de; Karapetyan, G. [Institute of Chemistry, University of Rostock, Albert-Einstein-Strasse 3a, 18059 Rostock (Germany); Nicula, R. [Institute of Physics, University of Rostock, August-Bebel-Strasse 55, 18055 Rostock (Germany); Stir, M. [Institute of Physics, University of Rostock, August-Bebel-Strasse 55, 18055 Rostock (Germany); National Institute for Materials Physics, 105b Atomistilor Strasse, P.O.B. MG7, 077125 Bucharest-Magurele (Romania); Schick, C. [Institute of Physics, University of Rostock, Universitaetsplatz 3, 18051 Rostock (Germany); Burkel, E. [Institute of Physics, University of Rostock, August-Bebel-Strasse 55, 18055 Rostock (Germany)

2008-02-05

Fine-grained ceramics of the Al{sub 2}O{sub 3}-TiO{sub 2} system were synthesised by reactive sintering of sol-gel precursors (Al- and Ti-alkoxides). The thermal behaviour of the as-prepared xerogels was examined by thermal analysis and X-ray powder diffraction. Preliminary results concerning powder consolidation into bulk ceramic parts using spark plasma sintering (SPS) are discussed.

El impacto diferenciado de la autoconfianza, los modelos de referencia y el miedo al fracaso sobre los jóvenes emprendedores

Directory of Open Access Journals (Sweden)

Eduardo Gómez-Araujo

2015-07-01

Full Text Available El objetivo principal de este trabajo es determinar el efecto que la autoconfianza en las habilidades emprendedoras y algunas variables socio-culturales (los modelos de referencia y el estigma social al fracaso ejercen sobre la actividad emprendedora de los jóvenes en España. Con tal finalidad se realiza un modelo de regresión logística para eventos extraños, utilizando la base de datos GEM-España de 2009, con una muestra de 24.099 personas. Los resultados más importantes indican que los jóvenes son más emprendedores que las personas mayores. Además, los resultados muestran que la autoconfianza y el estigma social al fracaso empresarial tienen un efecto diferenciado sobre la probabilidad emprendedora de jóvenes españoles

Determinação de diagramas de bandas de energia e da borda de absorção em SnO2, depositado via sol-gel, sobre quartzo Determination of the band energy diagram and absorption fundamental edge in SnO2, deposited via sol-gel, on quartz

Directory of Open Access Journals (Sweden)

E. A. Floriano

2009-03-01

Full Text Available Propriedades ópticas e estruturais de filmes finos de SnO2, depositados sobre substratos de quartzo, são apresentadas. Os filmes são preparados pela técnica de molhamento via sol-gel. Uma avaliação das propriedades eletrônicas do cristal (bulk e das superfícies (110 e (101 do material é também efetuada, através de cálculos baseados em um método mecânico-quântico que utiliza a Teoria do Funcional da Densidade (DFT em conjunto com o funcional hibrido B3LYP. A borda fundamental de absorção, obtida experimentalmente, é então comparada com os diagramas de bandas de energia do bulk e superfícies (110 e (101, calculadas.Optical and structural properties of SnO2 thin films, deposited on quartz substrates, are presented. Films are prepared by the sol-gel-dip-coating technique. An evaluation of the electronic properties of bulk and surfaces (110 and (101 of the material is also carried out, through calculation based on a quantum-mechanical method using the Density Functional Theory (DFT in conjunction with the hybrid functional B3LYP. The absorption fundamental edge, experimentally obtained, is compared to the calculated band energy diagram of bulk and surfaces (110 and (101.

Sol-Gel Derived Hafnia Coatings

Science.gov (United States)

Feldman, Jay D.; Stackpoole, Mairead; Blum, Yigal; Sacks, Michael; Ellerby, Don; Johnson, Sylvia M.; Venkatapathy, Ethiras (Technical Monitor)

2002-01-01

Sol-gel derived hafnia coatings are being developed to provide an oxidation protection layer on ultra-high temperature ceramics for potential use in turbine engines (ultra-efficient engine technology being developed by NASA). Coatings using hafnia sol hafnia filler particles will be discussed along with sol synthesis and characterization.

Información sobre la medicación y adherencia al tratamiento antirretroviral de gran actividad en pacientes con VIH/SIDA de un hospital de Lima, Perú

Directory of Open Access Journals (Sweden)

Juana Pacífico

Full Text Available Objetivos. Determinar la asociación entre la información sobre la medicación y adherencia al tratamiento antirretroviral de gran actividad (TARGA en pacientes con VIH/SIDA de un hospital de Lima, Perú. Materiales y métodos. Estudio de corte transversal analítico. Por medio de entrevistas se aplicó el cuestionario SIMS (Satisfaction with Information about Medicines Scale para medir la satisfacción con la información recibida sobre los medicamentos y el cuestionario SMAQ (Simplified Medication Adherence Questionnaire para determinar la adherencia al TARGA. Mediante revisión de historias clínicas se recogieron datos sociodemográficos y clínicos. Resultados. Se encuestaron 364 pacientes. La satisfacción con la información recibida sobre los medicamentos no estuvo asociada a la adherencia a TARGA (p=0,611. Factores asociados a la satisfacción con la información fueron: sexo femenino (ORa= 0,52; IC 95% 0,30- 0,90; el grado de instrucción superior (ORa=0,45; IC 95% 0,27-0,75 y la edad: ORa= 1,05 (IC 95% 1,02-1,08. Hubo mayor satisfacción con los informes recibidos sobre la acción y uso de los medicamentos frente a la información sobre sus potenciales reacciones adversas (48,9 vs. 43,1%; p=0,0291. Conclusiones. La satisfacción con la información recibida sobre los medicamentos no estuvo asociada a la adherencia a TARGA. La satisfacción con la información recibida sobre el TARGA se incrementa con la edad y es menor en mujeres y el grado de instrucción superior. Hay deseos de mayor información sobre las potenciales reacciones adversas al TARGA.

Inferencias sobre Grafos

Directory of Open Access Journals (Sweden)

Sira M. Allende

2002-05-01

Full Text Available El estudio de un juego puede ser modelado asumiendo que solo algunas partidas son observadas. Entonces el árbol del juego debe ser estimado utilizando información muestral. Similarmente ocurre al obtener información sobre el comportamiento de las decisiones tomadas por individuos muestreados sobre un árbol de decisión teórico. Al considerar una medida de probabilidad que caracterice el comportamiento de redes aleatorias se puede obtener un estimado del árbol asociado. Este problema es el analizado en este trabajo. Algunos resultados experimentales obtenidos usando Recocido Simulado ilustran el procedimiento. Su papel en el estudio de modelos económicos y de mercadeo es discutido.

Sol-gel technology for biomedical engineering

International Nuclear Information System (INIS)

Podbielska, H.; Ulatowska-Jarza, A.

2005-01-01

Sol-gel derived silica possess many promising features, including low-temperature preparation procedure, porosity, chemical and physical stability. Applications exploiting porous materials to encapsulate sensor molecules, enzymes and many other compounds, are developing rapidly. In this paper some potential applications, with emphasis on biomedical and environmental ones, are reviewed. The material preparation procedure is described and practical remarks on silica-based sol-gels are included. It is reported that sol-gels with entrapped various molecules may be used in construction of implants and coatings with bioactive properties. It is shown how to exploit the sol-gel production route for construction of sol-gel coated fiberoptic applicators for laser therapy. The applications of bioactive materials are discussed, as well. It is demonstrated that it is possible to immobilize photosensitive compounds in sol-gel matrix without loosing their photoactivity. Some examples of sol-gel based biosensors are demonstrated, as well, showing their potential for detecting various gases, toxic substances, acidity, humidity, enzymes and biologically active agents. (authors)

Compacting and crystallisation of transparent conductive oxidic sol-gel layers as illustrated by the example of zinc oxide; Verdichtung und Kristallisation von transparenten leitfaehigen oxidischen Sol-gel-Schichten am Beispiel des Zinkoxids

Energy Technology Data Exchange (ETDEWEB)

Schuler, T.

2003-07-01

flux (Al2O3 in ZnO:Al). (orig.) [German] In dieser Arbeit wurde gezeigt, dass ueber das preiswerte Sol-Gel-Tauchbeschichtungsverfahren dotierte Zinkoxid-Beschichtungen auf Glas hergestellt werden koennen. Der niedrigste erreichte spezifische Widerstand betraegt 1.1x10{sup -3}ohmcm fuer Mehrfach-Schichten aus Aluminium-dotiertem Zinkoxid. Es wurde gezeigt, dass fuer dicke Schichten die Kristallitgroesse von der Dotierung des Sols, der Temperatur und der Sinterzeit abhaengt, waehrend die Schichtdicke selbst massgeblich von der Konzentration der Loesung (Viskositaet) und der Ziehgeschwindigkeit bestimmt wird. Auf dieser Grundlage entstand ein Modell fuer die beobachteten Strukturen, das auch fuer andere Sol-Gel-Schichten anwendbar ist. Ueber den Prozessparameter p der Gleichung ESD = p x IKG kann so die Morphologie von Mehrfach-Schichten festgelegt werden. Der Strukturuebergang von der koernigen Struktur zur Lagen-Struktur wurde fuer p = 2.4 bis 3 und fuer den Uebergang von der Lagen-Struktur zur kolumnaren Struktur fuer p=1 festgelegt. Das vorgeschlagene Modell empfiehlt sich durch den Vergleich mit der Spruehpyrolyse auch als Prototypmodell fuer das Schichtwachstum dieser Technologie und kann darueber hinaus vermutlich auch auf physikalische Beschichtungstechnologien ausgeweitet werden. Die beobachtete Morphologie wirkt sich ueber die entstehenden Korngrenzen und die erreichte Verdichtung auf die elektrischen und damit auch auf die optischen Eigenschaften der Schichten aus. Mit steigender Verdichtung, sinkt folglich der spezifische Widerstand der Schicht. Es wurde demonstriert, dass die Beschichtungstemperatur durch Verringern der Einzelschichtdicke von 550 deg C auf 450 deg C verringert werden kann, ohne die Leitfaehigkeit zu verschlechtern. Zudem wurden Moeglichkeiten aufgezeigt, mittels anderer Sintertechnologien, wie dem pyrolytischen Gasflammen-Sintern und dem Laser-Sintern die Schichteigenschaften zu verbessern bzw. die Prozesszeit zu minimieren. Als groesstes

Gestion participative de la fertilite de sol en culture biologique d ...

African Journals Online (AJOL)

Ananas comosus dans un dispositif en blocs aléatoires avec 2 répétitions sur des parcelles élémentaires de 20 m² avec trois niveaux de doses de fientes de poulets et quatre doses de sulfate de potassium. Le sol a été analysé avant et après ...

Hybrid sol-gel optical materials

Science.gov (United States)

Zeigler, John M.

1992-01-01

Hybrid sol-gel materials comprise silicate sols cross-linked with linear polysilane, polygermane, or poly(silane-germane). The sol-gel materials are useful as optical identifiers in tagging and verification applications and, in a different aspect, as stable, visible light transparent non-linear optical materials. Methyl or phenyl silicones, polyaryl sulfides, polyaryl ethers, and rubbery polysilanes may be used in addition to the linear polysilane. The linear polymers cross-link with the sol to form a matrix having high optical transparency, resistance to thermooxidative aging, adherence to a variety of substrates, brittleness, and a resistance to cracking during thermal cycling.

Preparation and characterization of multi-walled carbon nanotube/hydroxyapatite nanocomposite film dip coated on Ti-6Al-4V by sol-gel method for biomedical applications: an in vitro study.

Science.gov (United States)

Abrishamchian, Alireza; Hooshmand, Tabassom; Mohammadi, Mohammadreza; Najafi, Farhood

2013-05-01

In the present research, the introduction of multi-walled carbon nanotubes (MWCNTs) into the hydroxyapatite (HA) matrix and dip coating of nanocomposite on titanium alloy (Ti-6Al-4V) plate was conducted in order to improve the performance of the HA-coated implant via the sol-gel method. The structural characterization and electron microscopy results confirmed well crystallized HA-MWCNT coating and homogenous dispersion of carbon nanotubes in the ceramic matrix at temperatures as low as 500 °C. The evaluation of the mechanical properties of HA and HA/MWCNT composite coatings with different weight percentages of MWCNTs showed that the addition of low concentrations of MWCNTs (0.5 and 1 wt.%) had improved effect on the mechanical properties of nanocomposite coatings. Moreover, this in vitro study ascertained the biocompatibility of the prepared sol-gel-derived HA/MWCNT composite coatings. Copyright © 2013 Elsevier B.V. All rights reserved.

La Sisactía de Solón y el juramento de los heliastas

OpenAIRE

Valdés Guía, Miriam

1999-01-01

La liberación del demos ateniense, sumido en una situación de dependencia y progresiva esclavización en Atenas arcaica, se asoció, con Solón, al culto a un dios, Zeus con el epíteto Eleutherios, y se garantizó mediante el establecimiento de las nuevas leyes y de la Heliea, cuyos miembros realizaban un juramento, instaurado en estos momentos, en el que significativamente se incluye también a Zeus con el epíteto Basileus (protector de las leyes en la poesía de Solón), junto a Apolo Patroos y D...

DISERTACIÓN SOBRE JUSTICIA Y EQUIDAD

Directory of Open Access Journals (Sweden)

Sayuri P. Tamura M.

2001-01-01

Full Text Available «Disertación sobre equidad y justicia» es básicamente una respuesta a una inquietud en particular que yo tenía sobre las distintas posiciones que existen sobre estos dos temas y cómo definir cuál es la más acertada. Hice una descripción del punto de vista de Amartya Sen –la violación de los derechos sobre la propiedad privada es justificable si evitan las hambrunas2– frente al de Robert Nozick –la propiedad privada es un derecho fundamental y como tal debe ser respetado3–, sin embargo, aunque ambos enfoques son totalmente contrarios tienen mucho sentido, por lo cual es bastante difícil decidirse por uno en particular. Fue de esta forma, enfrentando sus opiniones, que yo logré desarrollar una posición frente a estas dos perspectivas, y así dar mi opinión al DISERTACIÓN SOBRE JUSTICIA Y EQUIDAD SAYURI P. TAMURA M. Estudiante de Economía y Negocios Internacionales de la Universidad ICESI. respecto. Al final, llegué a una conclusión, que aunque no es la más original y tampoco es la única, tiene mucho sentido y seguramente de ser posible, la situación del país podría cambiar para bien.

Effect of sol concentration on the properties of ZnO thin films prepared by sol-gel technique

International Nuclear Information System (INIS)

Dutta, M.; Mridha, S.; Basak, D.

2008-01-01

ZnO thin films are deposited on the glass substrates by sol-gel drain coating technique by varying the concentration of the sol. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis were used to investigate the effect of sol concentration on the crystallinity and surface morphology of the films. The results show that with increase in sol concentration, the value of full width at half maximum (FWHM) of (0 0 2) peak decreases while the strain first increases and then decreases. The sol with higher concentration results in the increase in the grain size. The studies on the optical properties show that the band gap value increases from 3.27 to 3.3 eV when the sol concentration changes from 0.03 to 0.1 M. The photoconductivity studies reveal that the film for 0.05 M sol shows the maximum photoresponse for ultraviolet (UV) wavelength (<400 nm) which is co-related with the deep-level defects. The growth and decay of the photocurrent is found to be slowest for the same film

Efecto de la educación sexual sobre el comportamiento sexual de las adolescentes. Aplicación al caso colombiano

OpenAIRE

Bonilla López, María Fernanda

2016-01-01

Este trabajo analiza el efecto de la educación sexual sobre el comportamiento adolescente en Colombia, a través del estudio de los factores individuales y socioeconómicos asociados al riesgo de transitar al inicio de actividad sexual y el embarazo. Para esto se utiliza el análisis de un modelo de duración. Específicamente, se estima un modelo de riesgo proporcional. Los resultados muestran que las adolescentes expuestas a educación sexual, presentan menor riesgo en la transición hacía la acti...

Synthesis of Sol-Gel Precursors for Ceramics from Lunar and Martian Soil Simulars

Science.gov (United States)

Sibille, L.; Gavira-Gallardo, J. A.; Hourlier-Bahloul, D.

2004-01-01

Recent NASA mission plans for the human exploration of our Solar System has set new priorities for research and development of technologies necessary to enable a long-term human presence on the Moon and Mars. The recovery and processing of metals and oxides from mineral sources on other planets is under study to enable use of ceramics, glasses and metals by explorer outposts. We report initial results on the production of sol-gel precursors for ceramic products using mineral resources available in martian or lunar soil. The presence of SO2, TiO2, and Al2O3 in both martian (44 wt.% SiO2, 1 wt.% TiO2, 7 wt.% Al2O3) and lunar (48 wt.% SiO2, 1.5 wt.% TiO2, 16 wt.% Al2O3) soils and the recent developments in chemical processes to solubilize silicates using organic reagents and relatively little energy indicate that such an endeavor is possible. In order to eliminate the risks involved in the use of hydrofluoric acid to dissolve silicates, two distinct chemical routes are investigated to obtain soluble silicon oxide precursors from lunar and martian soil simulars. Clear solutions of sol-gel precursors have been obtained by dissolution of silica from lunar soil similar JSC-1 in basic ethylene glycol (C2H4(OH)2) solutions to form silicon glycolates. Similarly, sol-gel solutions produced from martian soil simulars reveal higher contents of iron oxides. Characterization of the precursor molecules and efforts to further concentrate and hydrolyze the products to obtain gel materials will be presented for evaluation as ceramic precursors.

Synthesis of Sol-Gel Precursors for Ceramics from Lunar and Martian Soil Simulars

Science.gov (United States)

Sibille, L.; Gavira-Gallardo, J. A.; Hourlier-Bahloul, D.

2003-01-01

Recent NASA mission plans for the human exploration of our Solar System has set new priorities for research and development of technologies necessary to enable a long-term human presence on the Moon and Mars. The recovery and processing of metals and oxides from mineral sources on other planets is under study to enable use of ceramics, glasses and metals by explorer outposts. We report initial results on the production of sol-gel precursors for ceramic products using mineral resources available in martian or lunar soil. The presence of SiO2, TiO2, and Al2O3 in both martian (44 wt.% SiO2, 1 wt.% TiO2,7 wt.% Al2O3) and lunar (48 wt.% SiO2, 1.5 wt.% TiO2, 16 wt.% Al2O3) soils and the recent developments in chemical processes to solubilize silicates using organic reagents and relatively little energy indicate that such an endeavor is possible. In order to eliminate the risks involved in the use of hydrofluoric acid to dissolve silicates, two distinct chemical routes are investigated to obtain soluble silicon oxide precursors from lunar and martian soil simulars. Clear solutions of sol-gel precursors have been obtained by dissolution of silica from lunar soil simular in basic ethylene glycol (C2H4(OH)2) solutions to form silicon glycolates. Similarly, sol-gel solutions produced from martian soil simulars reveal higher contents of iron oxides. The elemental composition and structure of the precursor molecules were characterized. Further concentration and hydrolysis of the products was performed to obtain gel materials for evaluation as ceramic precursors.

Nanocrystal/sol-gel nanocomposites

Science.gov (United States)

Petruska, Melissa A [Los Alamos, NM; Klimov, Victor L [Los Alamos, NM

2007-06-05

The present invention is directed to solid composites including colloidal nanocrystals within a sol-gel host or matrix and to processes of forming such solid composites. The present invention is further directed to alcohol soluble colloidal nanocrystals useful in formation of sol-gel based solid composites.

Effect of sol-age on the surface and optical properties of sol-gel derived mesoporous zirconia thin films

Directory of Open Access Journals (Sweden)

Manish Kumar

2011-06-01

Full Text Available Mesoporous ZrO2 thin films have been deposited by a modified sol-gel dip coating technique using HCl as catalyst. Effects of sol-age on the surface and on the optical properties are studied. Transmission electron micrographs of the films reveal the pore dimensions in mesoporous regime. A strong correlation in surface topography with sol-age has been observed where increase in sol-age induces a systematic enhancement in the value of root mean square roughness of the films. Optical study shows that deposited films have high transmittance and an enhancement of 5.6 times in porosity in films prepared with sol-age of 10 days with respect to that of 1 day. Band gap estimation by Tauc's plots of films is observed to 5.74 eV, which shows invariance with the sol-age.

Sol-gel synthesis of hydroxyapatite; Sintese de hidroxiapatita via sol-gel

Energy Technology Data Exchange (ETDEWEB)

Zupanski, M.D.; Lucena, M.P.P.; Bergmann, C.P., E-mail: michelledunin@yahoo.com.b [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil)

2010-07-01

Hydroxyapatite (HAp) has been established as the calcium phosphate based compound with most applications in the biological field. Among the numerous techniques for synthesis of HAp, the sol-gel processing route affords great control over purity and formed phases using low processing temperatures. In addition, the sol-gel approach offers an option for homogeneous HAp coating on metal substrates, as well as the ability to generate nanocrystalline powders. In this work, the sol-gel synthesis of HAp was investigated employing triethyl phosphate and calcium nitrate tetrahydrate as phosphorous and calcium precursors, respectively. The aging effect on phase composition and powder morphology of the final product was studied in terms of temperature and aging time. The powders were studied by using X-ray diffraction, Fourier transform infrared spectroscopy, particle size distribution by laser diffraction and scanning electron microscopy. (author)

Edificio Playa, en la Costa del Sol

Directory of Open Access Journals (Sweden)

Cassinello, Fernando

1964-02-01

Full Text Available This apartment block has been built on the Costa del Sol, in Almeria, only a few metres from the seashore. It is meant to provide the following facilities. Changing rooms for bathers, and a night club, in the basement. Restaurant and bar on the ground floor. Twelve living apartments on the six standard floor levels; two apartments per storey. Porter's house in the attic. As the foundations are in the sand, and the building is exposed to strong coastal winds, the structural design has, as interesting features, the foundation ribbed slab and the transversal portal frames, which are W shaped on the ground level. This arrangement makes the edifice look lighter and it acquires a more dynamic plasticity.En la Costa del Sol de Almería y a muy pocos metros de la orilla del mar, se ha construido este edificio de apartamentos. Su programa es el siguiente: casetas de baño y sala de fiestas, en sótano; restaurante-bar, en planta baja; doce viviendas, en las seis plantas tipo, con dos viviendas por planta; y vivienda del portero en ático. Cimentado sobre arena y expuesto a los fuertes vientos que azotan la costa, la solución estructural ofrece el interés de su tipo de cimentación por placa nervada, y de sus pórticos transversales que en planta baja adoptan forma de W, con lo que el edificio adquiere un aspecto de mayor ligereza y de dinamismo plástico.

HIDRODENITROGENACION DE CARBAZOL SOBRE CATALIZADORES NiMo/Al2O3-SiO2(x

Directory of Open Access Journals (Sweden)

Felipe Sánchez-Minero

2012-01-01

Full Text Available En este trabajo se estudió la velocidad de reacción del carbazol sobre catalizadores NiMo soportados sobre Al2O3 modificada superficialmente con SiO2 (0 y 10 % en peso de SiO2 en el soporte. Los catalizadores fueron evaluados en un reactor intermitente a cuatro temperaturas (287, 300, 312 y 325oC, presión de 4.0 MPa y relación molar hidrogeno/carbazol de 2400. A partir de los resultados experimentales se realizó un estudio cinético utilizando ecuaciones del tipo Langmuir-Hinshelwood (L-H. Luego, los parámetros cinéticos fueron estimados mediante la minimización de Powell (programa Scientist de MicroMath. Los resultados muestran que el catalizador con sílice (NiMo-SAC 10 alcanza una mayor actividad para la HDN de carbazol debido a que presenta un mayor número de sitios activos (valor de A, así como una menor fuerza de adsorción entre el reactante y la superficie catalítica (valor de KN, lo cual posiblemente favorece una mejor regeneración de sitios activos.

Preparation, microstructure and properties of yttrium aluminum garnet fibers prepared by sol-gel method

Energy Technology Data Exchange (ETDEWEB)

Li Chengshun [Key Laboratory for Liquid Structure and Heredity of Materials of Ministry of Education, Shandong University, Jinan 250061 (China); Zhang Yujun [Key Laboratory for Liquid Structure and Heredity of Materials of Ministry of Education, Shandong University, Jinan 250061 (China)], E-mail: yujunzhangcn@sdu.edu.cn; Gong Hongyu; Zhang Jingde; Nie Lifang [Key Laboratory for Liquid Structure and Heredity of Materials of Ministry of Education, Shandong University, Jinan 250061 (China)

2009-01-15

Yttrium aluminum garnet (YAG) fiber was prepared by sol-gel method using water as the solvent. The spinnable YAG sol was synthesized using Al powder, Y(CH{sub 3}COOH){sub 3}.4H{sub 2}O and HCl as precursors, polyethylene oxide as viscosity adjusting agent. Gel fibers with diameter of 5-10 {mu}m were prepared from the YAG sol by using centrifugal spinning technique. YAG crystalline fibers were obtained by drying gel fibers and heat-treating at selected temperature. TG/DTA analysis showed an exotherm at 906 deg. C attributed to formation of YAG phase and weight loss of 45% at 1000 deg. C. XRD and FT-IR analysis showed that phase-pure YAG can be formed at 900 deg. C, and no other intermediate was observed. The grain size of YAG fibers increased from 25 to 220 nm and tensile strength decreased rapidly from 970 to 380 MPa when the sintering temperature increased from 900 to 1550 deg. C.

Low Concentration Fe-Doped Alumina Catalysts Using Sol-Gel and Impregnation Methods: The Synthesis, Characterization and Catalytic Performance during the Combustion of Trichloroethylene

Directory of Open Access Journals (Sweden)

Carolina Solis Maldonado

2014-03-01

Full Text Available The role of iron in two modes of integration into alumina catalysts was studied at 0.39 wt% Fe and tested in trichloroethylene combustion. One modified alumina was synthesized using the sol-gel method with Fe added in situ during hydrolysis; another modification was performed using calcined alumina, prepared using the sol-gel method and impregnated with Fe. Several characterization techniques were used to study the level of Fe modification in the γ-Al2O3 phase formed and to correlate the catalytic properties during trichloroethylene (TCE combustion. The introduction of Fe in situ during the sol-gel process influenced the crystallite size, and three iron species were generated, namely, magnetite, maghemite and hematite. The impregnated Fe-alumina formed hematite and maghemite, which were highly dispersed on the γ-Al2O3 surface. The X-ray photoelectron spectra (XPS, FT-IR and Mössbauer spectroscopy analyses revealed how Fe interacted with the γ-Al2O3 lattice in both catalysts. The impregnated Fe-catalyst showed the best catalytic performance compared to the catalyst that was Fe-doped in situ by the sol-gel method; both had better catalytic activity than pure alumina. This difference in activity was correlated with the accessibility of the reactants to the hematite iron species on the surface. The chlorine poisoning for all three catalysts was less than 1.8%.

Dielectric Properties of Sol-Gel Derived Barium Strontium Titanate and Microwave Sintering of Ceramics

Science.gov (United States)

Selmi, Fathi A.

This thesis consists of two areas of research: (1) sol-gel processing of Ba_{rm 1-x}Sr_{rm x} TiO_3 ceramics and their dielectric properties measurement; and (2) microwave versus conventional sintering of ceramics such as Al_2 O_3, Ba_{ rm 1-x}Sr_{rm x}TiO_3, Sb-doped SnO _2 and YBa_2Cu _3O_7. Sol-gel powders of BaTiO_3, SrTiO_3, and their solid solutions were synthesized by the hydrolysis of titanium isopropoxide and Ba and Sr methoxyethoxides. The loss tangent and dielectric constant of both sol-gel and conventionally prepared and sintered Ba_{rm 1-x}Sr _{rm x}TiO _3 ceramics were investigated at high frequencies. The sol-gel prepared ceramics showed higher dielectric constant and lower loss compared to those prepared conventionally. Ba _{rm 1-x}Sr _{rm x}TiO_3 ceramics were tunable with applied bias, indicating the potential use of this material for phase shifter applications. Porous Ba_{0.65}Sr _{0.35}TiO_3 was also investigated to lower the dielectric constant. Microwave sintering of alpha -Al_2O_3 and SrTiO_3 was investigated using an ordinary kitchen microwave oven (2.45 GHz; 600 Watts). The use of microwaves with good insulation of alpha -Al_2O_3 and SrTiO_3 samples resulted in their rapid sintering with good final densities of 96 and 98% of the theoretical density, respectively. A comparison of grain size for conventionally and microwave sintered SrTiO_3 samples did not show a noticeable difference. However, the grain size of microwave sintered alpha-Al_2O _3 was found to be larger than that of conventionally sintered sample. These results show that rapid sintering of ceramics can be achieved by using microwave radiation. The sintering behavior of coprecipitated Sb-doped SnO_2 was investigated using microwave power absorption. With microwave power, samples were sintered at 1450^circC for 20 minutes and showed a density as high as 99.9% of theoretical. However, samples fired in a conventional electric furnace at the same temperature for 4 hours showed only

Sol-gel bonding of silicon wafers

International Nuclear Information System (INIS)

Barbe, C.J.; Cassidy, D.J.; Triani, G.; Latella, B.A.; Mitchell, D.R.G.; Finnie, K.S.; Short, K.; Bartlett, J.R.; Woolfrey, J.L.; Collins, G.A.

2005-01-01

Sol-gel bonds have been produced between smooth, clean silicon substrates by spin-coating solutions containing partially hydrolysed silicon alkoxides. The two coated substrates were assembled and the resulting sandwich fired at temperatures ranging from 60 to 600 deg. C. The sol-gel coatings were characterised using attenuated total reflectance Fourier transform infrared spectroscopy, ellipsometry, and atomic force microscopy, while the corresponding bonded specimens were investigated using scanning electron microscopy and cross-sectional transmission electron microscopy. Mechanical properties were characterised using both microindentation and tensile testing. Bonding of silicon wafers has been successfully achieved at temperatures as low as 60 deg. C. At 300 deg. C, the interfacial fracture energy was 1.55 J/m 2 . At 600 deg. C, sol-gel bonding provided superior interfacial fracture energy over classical hydrophilic bonding (3.4 J/m 2 vs. 1.5 J/m 2 ). The increase in the interfacial fracture energy is related to the increase in film density due to the sintering of the sol-gel interface with increasing temperature. The superior interfacial fracture energy obtained by sol-gel bonding at low temperature is due to the formation of an interfacial layer, which chemically bonds the two sol-gel coatings on each wafer. Application of a tensile stress on the resulting bond leads to fracture of the samples at the silicon/sol-gel interface

La traduccion del conocimiento en cancer cervicouterino: una brecha entre la investigacion sobre las causas y la investigacion sobre la atencion al paciente?

Directory of Open Access Journals (Sweden)

David Fajardo-Ortiz

2014-02-01

Full Text Available En este trabajo construimos un mapa de la traducción del conocimiento sobre cáncer cervicouterino, basado en el análisis de redes de citación y en el uso de términos del “Gene Ontology” y del Medical Heading Subject. Identificamos dos campos de investigación sobre cáncer cervicouterino, pobremente conectados entre sí, que difieren en estructura, contenido y evolución. Un área esta centrada en el estudio de las causas de la enfermedad, mientras que la otra se centra en la atención al paciente. En la primera área encontramos un proceso de traducción del conocimiento en la que la investigación clínica y la investigación básica se comunican a través de un conjunto de artículos que consolidan la infección por el papilomavirus como la causa necesaria del cáncer cervicouterino. La primera área está orientada a prevenir la infección por el virus del papiloma humano y el subsecuente desarrollo del cáncer cervicouterino, mientras que la otra área se ocupa de la estadificación y tratamiento de la enfermedad.

Deshidratación osmótica de la papaya chilena (Vasconcellea pubescens e influencia de la temperatura y concentración de la solución sobre la cinética de transferencia de materia Desidratação osmótica do mamão chileno (Vasconcellea pubescens e influência da temperatura e concentração da solução sobre a cinética de transferência de matéria

Directory of Open Access Journals (Sweden)

Antonio Vega-Gálvez

2007-09-01

Full Text Available El objetivo de este trabajo fue estudiar la cinética de deshidratación osmótica de la papaya chilena (Vasconcellea pubescens, utilizando dos variables experimentales: la temperatura (30, 40, 50 °C y concentración (40, 50 y 60% de la solución osmótica. Se determinó la variación de masa total, masa de agua y masa de sólidos solubles y se modeló con las ecuaciones difusionales, además en esta investigación se consideró y utilizó una modificación de la ecuación propuesta por Biswal-Bozorgmehr. Estos modelos fueron evaluados por medio del coeficiente de regresión lineal, suma de errores cuadrados, raíz media de los errores cuadrados y Chi-cuadrado. Al comparar los valores experimentales con los calculados, se demostró que el modelo Biswal-Bozorgmehr modificado obtuvo mejor ajuste sobre la variación de masa de agua y sólidos solubles. Mediante la ecuación de Arrhenius se analizó el efecto de la temperatura sobre los parámetros cinéticos (Kw y Kss y difusividad efectiva de agua (Dwe y sólidos solubles (Dsse. De acuerdo al diseño factorial, se observó que la temperatura no influyó sobre la difusividad efectiva de agua y de sólidos, pero sí la concentración de la solución osmótica. La mejor condición de salida de agua y ganancia de sólidos solubles durante la deshidratación osmótica de la papaya chilena fue a 30 °C con una concentración del 60%.O objetivo deste trabalho foi estudar a cinética de desidratação osmótica do mamão chileno (Vasconcellea pubescens utilizando duas variáveis experimentais: temperatura (30, 40 e 50 °C e concentração (40, 50 e 60% da solução osmótica. Para este estudo, determinou-se a variação de massa total, de massa de água, de massa de sólidos solúveis, modeladas com as equações difusionais. Nesta investigação, também se considera e se usa uma modificação da equação proposta por Biswal-Bozorgmehr. Estes modelos foram avaliados através do coeficiente de regress

Reflejos territoriales en destinos religiosos y de sol y playa. De Fátima a Benidorm

OpenAIRE

Santos Solla, Xosé Manuel

2015-01-01

El objetivo de este artículo es reflexionar sobre destinos turísticos neogénicos surgidos a partir de motivaciones diferentes. En concreto focalizamos el trabajo en dos localidades ibéricas seleccionadas como representativas del turismo religioso y de sol y playa: Fátima y Benidorm. Los argumentos que desarrollamos insisten en la idea de que la aparición y evolución de estos destinos no es neutra desde el punto de vista geográfico. Del mismo modo existen coincidencias a la hora de entender su...

Sol-gel processing to form doped sol-gel monoliths inside hollow core optical fiber and sol-gel core fiber devices made thereby

Science.gov (United States)

Shaw, Harry C. (Inventor); Ott, Melanie N. (Inventor); Manuel, Michele V. (Inventor)

2002-01-01

A process of fabricating a fiber device includes providing a hollow core fiber, and forming a sol-gel material inside the hollow core fiber. The hollow core fiber is preferably an optical fiber, and the sol-gel material is doped with a dopant. Devices made in this manner includes a wide variety of sensors.

La posesión agraria individual en los registros notariales de Fuente El Sol (1481-1482 = Individual Agrarian Property Holding in the Notary Records of Fuente El Sol (1481-1482

Directory of Open Access Journals (Sweden)

Laura da Graca

2018-05-01

Full Text Available Se analizan diversas prácticas de los productores agrarios a partir de los registros notariales de Fuente el Sol, lugar de señorío privado en el obispado de Ávila. El objetivo del trabajo es documentar el supuesto teórico según el cual la gestión autónoma de la unidad de producción conlleva un posicionamiento individualista y antiseñorial. Se examinan las infracciones sobre tierras particulares, las disputas en torno al patrimonio familiar y la actuación de tenentes acusados de diversas faltas. Se demuestra la continuidad entre la orientación individualista y la resistencia a las imposiciones señoriales, y se revelan estrategias de resguardo y ampliación de la posesión agraria individual, que en ocasiones reproducen mecanismos de lucha contra la renta, como el intento de ocultar el volumen de producción y las transacciones. Se observa la condición cambiante de la unidad productiva, sujeta a constante recomposición, lo cual se asocia a la vocación de dirigir libremente la actividad económica. This article explores some practices of the agrarian producers on the basis of the notary records of Fuente el Sol, a village within a lordship in the bishopric of Ávila. The aim is to document the theoretical assumption that autonomous management of the unit of production involves both individualistic attitudes and resistance to the lord. We will analyse trespassing offences, disputes over family inheritance, and the action of tenants accused of different violations. We will demonstrate the link between the individual approach and resistance to seigneurial impositions, as well as some strategies aiming at protecting and enlarging individual property holdings, strategies that at times reproduce procedures of the struggle against rent incomes, such as concealing the volume of production and transactions. We will also consider the changing composition of the unit of production, an aspect associated with the purpose of freely managed

Deformaciones faciales y sus influencias sobre el psiquismo

Directory of Open Access Journals (Sweden)

Guillermo Nieto Cano

1957-04-01

Full Text Available Creemos haber dejado establecido, en síntesis, que todas las minusvalías físicas repercuten sobre el psiquismo, y que entre éstas las deformaciones faciales, por su ostentosa evidencia, son las que afectan más seriamente al individuo y modifican por eso más radicalmente su conducta, incidiendo así, en forma trascendental, sobre la colectividad. Tales defectos constituyen, por consiguiente, un serio problema humano, cuyo estudio y remedio incumbe no solamente al esteta cirujano, sino que interesa a todos aquellos que puedan influir sobre la estabilidad armónica y la buena marcha de la sociedad en que viven.

Optimal hysteretic control for a B M A P &sol; S M &sol; 1 &sol; N queue with two operation modes

Directory of Open Access Journals (Sweden)

Dudin Alexander N.

1999-01-01

Full Text Available We consider B M A P &sol; S M &sol; 1 type queueing system with finite buffer of size N . The system has two operation modes, which are characterized by the matrix generating function of B M A P -input, the kernel of the semi-Markovian service process, and utilization cost. An algorithm for determining the optimal hysteresis strategy is presented.

Aplicación de la teoría de seguridad al diseño geotécnico de losas sobre pilotes

Directory of Open Access Journals (Sweden)

Raydel Lorenzo

2013-01-01

Full Text Available En este articulo se da una panorámica de los métodos de cálculo de la capacidad de carga de cimentaciones de tipo losa sobre pilotes (piled raft seleccionando, de acuerdo al estudio bibliográfico realizado, el que arroja resultados más cercanos a estudios de experimentales y numéricos. Se presenta la forma de aplicación del método de estados límites al diseño geotécnico de este tipo de cimentación, definiendo el sistema de coeficientes parciales necesarios para la introducción de la seguridad a través de este método para el estado último. Se muestra la aplicación de la Teoría de Seguridad y de los métodos probabilisticos en el diseño geotécnico, definiendo todo el aparato matemático necesario en el caso específico de las losas sobre pilotes. Finalmente se presenta la metodología para la calibración de los coeficientes parciales a utilizar en el método de estados límites a partir de la aplicación de los métodos probabilísticos y se obtienen, para el método seleccionado de determinación de la capacidad de carga, todas las expresiones necesarias para la calibración en el caso específico de las losas sobre pilotes.

Sol-gel-state of hydrated zirconium dioxide

International Nuclear Information System (INIS)

Karakchiev, L.G.; Lyakhov, N.Z.

1995-01-01

The change in viscosity and density of a system in the course of sol-gel-xerogel has been traced. The size and molecular mass of particles in sol have been determined. Initial sol is practically a monodisperse system. Gel is a spatial net of similar particles. Reversible character of sol-gel transition with a change in water content in the system suggests instability of the bond between the particles in the structure of the solid state body formed. 11 refs.; 4 figs

Oxidación de propileno sobre catalizadores Pt-Cu/y-alúmina. Segunda Parte: Cinética química de catalizadores de Pt-Cu/y-alúmina en la oxidación de propileno

Directory of Open Access Journals (Sweden)

Luis M. Carballo

1999-09-01

Full Text Available En este trabajo se trata el efecto de la composición de catalizadores de Pt-Cu/j-alúmína sobre la actividad superficial específica correspondiente a la oxidación total de propileno. Aunque la actividad del catalizador de Cu fue prácticamente nula, a las condiciones de operación, la actividad específica del catalizador Pt-Cu se incrementó con el aumento de la proporción contenida de Cu en el catalizador. La velocidad global total, por gramo de catalizador, también se incrementó con la introducción de Cu, pero únicamente a concentraciones medias y altas de propileno. La actividad superficial específica fue mayor para el catalizador sinterizado, para una composición dada del catalizador bimetálico, comparada con la del catalizador fresco (no sinterizado. Para explicar el comportamiento catalítico de la oxidación de propileno, sobre los catalizadores aquí estudiados, se postula que la molécula de propileno se adsorbe con menos fuerza sobre las caras que sobre las esquinas o bordes de los cristales del catalizador, y que el enlace de adsorción sobre un sitio de Pt dado se ve afectado por los átomos de Cu vecinos sobre la superficie causando cambios en la movilidad de las especies adsorbidas. Los resultados cinéticos revelan una dependencia compleja entre la velocidad de reacción y la concentración del propileno. A concentraciones bajas de propileno la velocidad de reacción se incrementó con la concentración hasta que alcanzó un máximo, para seguir con un decrecimiento marcado; y a concentraciones mayores de propileno la cinética de reacción se presenta como de orden cero con respecto al propileno, para unas concentraciones dadas de oxígen o.

Evaluation of sol-gel derived Eu2+ activated SrMgAl2SiO7 as a novel nanostructure luminescent pigment

International Nuclear Information System (INIS)

Sameie, H.; Salimi, R.; Sabbagh Alvani, A.A.; Sarabi, A.A.; Moztarzadeh, F.; Tahriri, M.

2010-01-01

A novel nanostructure pigment of Eu 2+ doped SrMgAl 2 SiO 7 was prepared via the sol-gel route. The phase composition and condition of crystallites during heating were characterized by X-ray diffraction (XRD) analysis. Investigation of optical properties by spectrophotometer illustrated that under short ultraviolet excitation wavelength, the main emission peak occurred at about 415-420 nm. Also, relatively pure purplish blue color was observed that can be ascribed to the 4f 6 5d 1 ( 2 D)→4f 7 ( 8 S 7/2 ) transition of Eu 2+ . The effect of calcination temperature on the luminescence properties of the phosphors was evaluated and, also in this case, scanning electron microscope (SEM) was employed. From colorimetry results, color coordinations of phosphor shift towards the deep blue region as calcination temperature increases. Finally, grain size of products at optimum calcination temperature was estimated to be about 20-30 nm using Scherrer's equation, which was consistent with transmission electron microscopy (TEM) observations.

Oxidación de propileno sobre catalizadores Pt-Cu/y-alúmina. Primera Parte: Caracterización de catalizadores de Pt-Cu/y-alúmina por quimisorción de H2

Directory of Open Access Journals (Sweden)

Luis M. Carballo

1999-09-01

Full Text Available En este trabajo se analiza el efecto de la composición de catalizadores de Pt-Cu/y-alúmina sobre el área superficial reactiva correspondiente a la oxidación total de propileno. Los ensayos experimentales se efectuaron en un reactor diferencial que se usó tanto para la caracterización del catalizador "in situ" mediante la medición de la quimisorción selectiva de H2. Además, se discuten los efectos y las interacciones bimetálicas que ocurren con frecuencia en los catalizadores soportados. A partir de los estudios de adsorción química de H2 sobre los catalizadores soportados de Pt-Cu se encontró, mediante la aplicación de la teoría de la solución regular a la superficie de los cristales y teniendo en cuenta que el H2 se adsorbe químicamente solamente sobre los átomos superficiales de Pt (se observó que el hidrógeno no se quimisorbe sobre el Cu, que los átomos de Cu se segregan a la superficie de los cristalitos bimetálicos.

Method of making ionic liquid mediated sol-gel sorbents

Science.gov (United States)

Malik, Abdul; Shearrow, Anne M.

2017-01-31

Ionic liquid (IL)-mediated sol-gel hybrid organic-inorganic materials present enormous potential for effective use in analytical microextraction. One obstacle to materializing this prospect arises from high viscosity of ILs significantly slowing down sol-gel reactions. A method was developed which provides phosphonium-based, pyridinium-based, and imidazolium-based IL-mediated advanced sol-gel organic-inorganic hybrid materials for capillary microextraction. Scanning electron microscopy results demonstrate that ILs can serve as porogenic agents in sol-gel reactions. IL-mediated sol-gel coatings prepared with silanol-terminated polymers provided up to 28 times higher extractions compared to analogous sol-gel coatings prepared without any IL in the sol solution. This study shows that IL-generated porous morphology alone is not enough to provide effective extraction media: careful choice of the organic polymer and the precursor with close sol-gel reactivity must be made to ensure effective chemical bonding of the organic polymer to the created sol-gel material to be able to provide the desired sorbent characteristics.

Sol-gel additive for systems with inorganic binders

International Nuclear Information System (INIS)

Akstinat, M.; Antenen, D.; Suter, W.

1996-01-01

A sol-gel additive for inorganic binder systems and sol-gel process for producing air-placed concrete and mortar by using such sol-gel additives are disclosed. Sol-gel additives for gel-derived inorganic binder systems (for example plaster, cement, lime, special slags, etc.) marked improve the consistency of such binder systems during processing or allow their consistency to be regulated. In addition, these sol-gel additives regulate setting times and substantially improve durability (chemical resistance, reduced permeability) and the mechanical properties of the set binder system. (author)

Influencia del tratamiento térmico sobre el espesor y porosidad de películas delgadas de ZrO2 obtenidas por la ruta sol-gel

Directory of Open Access Journals (Sweden)

Caruso, R.

2004-04-01

Full Text Available The present work is aimed to investigate the thermal densification mechanisms of sol-gel zirconia thin films deposited by dip coating, with particular emphasis on thickness and porosity evolution at different firing treatments (100-1100ºC. For this purpose, we have only used data from transmission spectrum. Implications for controlled design of sol-gel zirconia films will be considered.El este trabajo se investigan los mecanismos de densificación de películas delgadas de zirconia obtenidas por vía sol-gel y depositadas mediante la técnica dip-coating. Nuestro interés se centra en la determinación del espesor y porosidad de películas tratadas a temperaturas en el rango 100-1100 ºC. Para ello, se ha utilizado exclusivamente la técnica de espectrofotometría. Los resultados de este trabajo tienen interés para el diseño controlado de recubrimientos sol-gel de ZrO2.

Effect of Chelating Agents on the Stability of Nano-TiO2 Sol Particles for Sol-Gel Coating.

Science.gov (United States)

Maeng, Wan Young; Yoo, Mi

2015-11-01

Agglomeration of sol particles in a titanium alkoxide (tetrabutyl orthotitanate (TBOT), > 97%) solution during the hydrolysis and condensation steps makes the sol solution difficult to use for synthesizing homogeneous sol-gel coating. Here, we have investigated the effect of stabilizing agents (acetic acid and ethyl acetoacetate (EAcAc)) on the agglomeration of Ti alkoxide particles during hydrolysis and condensation in order to determine the optimized conditions for controlling the precipitation of TiO2 particles. The study was conducted at R(AC) ([acetic acid]/[TBOT]) = 0.1-5 and R(EAcAc)([EAcAc]/[TBOT]) = 0.05-0.65. We also studied the effects of a basic catalyst ethanolamine (ETA), water, and HCl on sol stability. The chelating ligands in the precursor sol were analyzed with FT-IR. The coating properties were examined by focused ion beam. The stabilizing agents (acetic acid and EAcAc) significantly influenced the agglomeration and precipitation of TBOT precursor particles during hydrolysis. As R(AC) and R(EAcAc) increased, the agglomeration remarkably decreased. The stability of the sol with acetic acid and EAcAc arises from the coordination of the chelating ligand to TBOT that hinders hydrolysis and condensation. A uniform fine coating (thickness: 30 nm) on stainless steel was obtained by using an optimized sol with R(AC) = 0.5 and R(EAcAc) = 0.65.

Structural evolution of silica sols modified with formamide

Directory of Open Access Journals (Sweden)

Lenza R.F.S.

2001-01-01

Full Text Available In this work we investigated the influence of formamide on the acid-catalyzed sol-gel process by Fourier transform infrared spectroscopy (FTIR. Three silica sols were studied: Sol catalyzed with nitric acid without formamide, sol catalyzed with nitric acid containing formamide and sol catalyzed with a mixture of nitric acid and hydrofluoric acid and modified with formamide. Following the time evolution of both the Si-(OH stretching vibration at around 950 cm-1 and the Si-O-(Si vibration between 1040 cm-1 and 1200 cm-1 we were able to describe the structural evolution of each sol. The curve of evolution of Si-(OH stretching vibration corresponding to sol A has a simple asymptotic evolution. In the case of formamide containing sol, we observed a two-step structural evolution indicating that for the system containing formamide the polymerization goes through a temporary stabilization of oligomers, which can explain the non-variation of the Si-O(H bond wavenumber for a certain time. Gelation times were of several days for gels without formamide and few hours for gels containing additive. The presence of additive resulted in a highly interconnected gel.

Adaptación al español del instrumento sobre cultura organizacional de Denison

Directory of Open Access Journals (Sweden)

Tomás Bonavia

2013-08-01

Full Text Available En este estudio se presentan los resultados de la adaptación a grupos I+D universitarios de habla hispanade la encuesta sobre cultura organizacional de Denison. Este cuestionario, compuesto por 60 ítems que identifican 12 tipos culturales, que a su vez se agrupan en cuatro dimensiones, ha demostrado su influencia para aumentar la efectividad organizacional. La adaptación al castellano que aquí se propone ha sido aplicada a 488 personas pertenecientes a 39 grupos de I+D tecnológicos de la Universidad Politécnica de Valencia. Los resultados obtenidos muestran unas propiedades psicométricas adecuadas para la adaptación realizada en cuanto a validez y fiabilidad, que replican casi en su totalidad la estructura del modelo de la versión original.

Characterization of the calcium-fluoroaluminosilicate glass prepared by a non-hydrolytic sol-gel route for future dental application as glass ionomer cement

Directory of Open Access Journals (Sweden)

Alexandre Cestari

2009-06-01

Full Text Available Glass ionomer cements are widely employed in dentistry due to their physical, biological and mainly anti-caries properties. Glass ionomers consist of an aluminosilicate glass matrix modified with other elements, and they contain large quantities of fluorine. In this study, we report on the preparation of calcium-fluoroaluminosilicate glasses by a nonhydrolytic sol-gel route as an alternative approach to obtaining alumina-silica matrices. The glass powders were prepared via the non-hydrolytic sol-gel method, by mixing AlCl3, SiCl4, CaF2, AlF3, NaF, and AlPO4. The powders were studied by thermal analysis (TG/DTA/DSC, photoluminescence (PL, nuclear magnetic resonance (NMR27Al-29Si, and X ray diffraction (XRD. TG/DTA/DSC analyses revealed a constant mass loss due to structural changes during the heating process, which was confirmed by NMR and PL. A stable aluminosilicate matrix with potential future application as a glass ionomer base was obtained.

Functional coatings: the sol-gel approach

International Nuclear Information System (INIS)

Belleville, Ph.

2010-01-01

CEA's sol-gel laboratory is specialized in the development of innovative sol-gel optical coatings and has extended its application field to membrane materials and coatings for energy conversion, to electric coatings for microelectronics devices and to thin films for gas sensing. This article describes, by way of examples, the laboratory's research on sol-gel functional coatings, including nano-material synthesis, organic-inorganic hybrid-based solution preparation as well as deposition process development and prototyping. (author)

Comentarios sobre la Ley de Ordenamiento Territorial Sostenible

Directory of Open Access Journals (Sweden)

Arturo J. Yglesias

2014-04-01

Full Text Available La denominada Ley de Ordenamiento Territorial Sostenible, no fue bien recibida en el medio jurídico. Tanto los profesores de las diferentes materias de Derecho de nuestra Facultad como las asociaciones profesionales y otros grupos e juristas de nuestro medio, formularon reservas de diverso calibre sobre el texto de la ley que van desde sus aspectos adjetivos como la terminología y redacción hasta cuestiones sustanciales como lo que ella dice sobre el régimen de la propiedad territorial y otras cuestiones vinculadas.Desde el discurso político vimos lanzar opiniones iracundas y alarmistas sobre las modificaciones que la ley estaría haciendo al régimen de la propiedad privada, sobre su supuesta inconstitucionalidad.Nosotros nos vamos a referir a la ley a sus antecedentes y de las críticas que se le hacían, en la parte que toca a nuestra materia, esto es en lo relativo al régimen de la propiedad y debemos decir, a vía de adelanto, que no vemos en ella nada que afecte el derecho de propiedad consagrado por la Constitución de la República, ni los principios generales que regulan la propiedad territorial conforme al Código Civil, conforme a la vieja ley de Centros Poblados, sus modificativas ni demás normas sobre la materia.

The SOL width and the MHD interchange instability in tokamaks

Energy Technology Data Exchange (ETDEWEB)

Kerner, W [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Pogutse, O [Kurchatov institute, Moscow (Russian Federation)

1994-07-01

Instabilities in the SOL plasma can strongly influence the SOL plasma behaviour and in particular the SOL width. The SOL stability analysis shows that there exists a critical ratio of the thermal energy and the magnetic energy. If the SOL beta is greater than this critical value, the magnetic field cannot prevent the plasma displacement and a strong MHD instability in the SOL occurs. In the opposite case only slower resistive instabilities can develop. A theoretical investigation of the SOL plasma stability is presented for JET single-null and double-null divertor configurations. The dependence of the stability threshold on the SOL beta and on the sheath resistance is established. Applying a simple mixing length argument gives the scaling of the SOL width. 5 refs., 2 figs.

Percepción del riesgo al cambio climático y sus efectos sobre la salud y enfermedades infecciosas en estudiantes universitarios, 2011 Santa Marta - Colombia

Directory of Open Access Journals (Sweden)

Alexander Salazar Ceballos

2014-06-01

Full Text Available Introducción: La Organización Mundial de la Salud (OMS ha denominado que el cambio climático es una amenaza para la salud pública, por lo tanto es necesario conocer la percepción del riesgo al cambio climático específicamente en los futuros profesionales de la salud. Materiales y Métodos: Se realizó una investigación de tipo cuantitativo descriptiva con muestreo aleatorio estratificado. Se realizaron análisis de Chi2 y regresión logística para identificar los factores asociados a la percepción del riesgo al cambio climático y al aumento de enfermedades infecciosas sensibles al cambio climático en estudiantes universitarios de las ciencias de la salud en la Universidad del Magdalena. Resultados: Por Chi2 se encontró que cerca del 69% de los estudiantes perciben el cambio climático como dañino y entre 50 y 59% de ellos perciben que las enfermedades infecciosas aumentarán como consecuencia del cambio climático. Por regresión logística se observó significancia estadística que los estudiantes que pertenecen al sexto semestre de estudios o semestres superiores tienen 60% más probabilidad de reconocer que pueden enfermarse por el cambio climático, 63% más probabilidad de percibir el cambio climático como dañino, relacionaron 2,2 veces más el aumento de la temperatura global con el aumento de enfermos con fiebre amarilla y dengue, también tienen 58% más posibilidad de relacionar el aumento de los casos. Discusión: Los estudiantes de los diferentes programas de salud que pertenecen al sexto semestre de estudios o superiores percibieron el cambio climático como una amenaza sobre la salud pública y lo asociaron con el aumento de enfermedades infecciosas, de esta manera, se puede considerar que los estudiantes de salud conforme avanzan en los semestres académicos perciben un mayor riesgo del cambio climático como una amenaza sobre la salud pública y un aumento de los enfermos por enfermedades infecciosas

Sol-gel method for encapsulating molecules

Science.gov (United States)

Brinker, C. Jeffrey; Ashley, Carol S.; Bhatia, Rimple; Singh, Anup K.

2002-01-01

A method for encapsulating organic molecules, and in particular, biomolecules using sol-gel chemistry. A silica sol is prepared from an aqueous alkali metal silicate solution, such as a mixture of silicon dioxide and sodium or potassium oxide in water. The pH is adjusted to a suitably low value to stabilize the sol by minimizing the rate of siloxane condensation, thereby allowing storage stability of the sol prior to gelation. The organic molecules, generally in solution, is then added with the organic molecules being encapsulated in the sol matrix. After aging, either a thin film can be prepared or a gel can be formed with the encapsulated molecules. Depending upon the acid used, pH, and other processing conditions, the gelation time can be from one minute up to several days. In the method of the present invention, no alcohols are generated as by-products during the sol-gel and encapsulation steps. The organic molecules can be added at any desired pH value, where the pH value is generally chosen to achieve the desired reactivity of the organic molecules. The method of the present invention thereby presents a sufficiently mild encapsulation method to retain a significant portion of the activity of the biomolecules, compared with the activity of the biomolecules in free solution.

Sol-gel derived sorbents

Science.gov (United States)

Sigman, Michael E.; Dindal, Amy B.

2003-11-11

Described is a method for producing copolymerized sol-gel derived sorbent particles for the production of copolymerized sol-gel derived sorbent material. The method for producing copolymerized sol-gel derived sorbent particles comprises adding a basic solution to an aqueous metal alkoxide mixture for a pH.ltoreq.8 to hydrolyze the metal alkoxides. Then, allowing the mixture to react at room temperature for a precalculated period of time for the mixture to undergo an increased in viscosity to obtain a desired pore size and surface area. The copolymerized mixture is then added to an immiscible, nonpolar solvent that has been heated to a sufficient temperature wherein the copolymerized mixture forms a solid upon the addition. The solid is recovered from the mixture, and is ready for use in an active sampling trap or activated for use in a passive sampling trap.

The influence of p H and UV visible absorption on hydrolysis stage and gel behavior of glasses synthesized by sol-gel

International Nuclear Information System (INIS)

Khosravi Saghezchi, M.; Sarpoolaky, H.; Heshmatpour, F.

2008-01-01

Lead-containing glass borosilicate was synthesized by Sol-gel technique using metal alkoxide such as tetra ethyleorthosilicate, Al-sec-butoxide and trimethyl borate. The sol containing tetra ethyle ortho silicate converts to gel during drop wise addition of Al-alkoxide while inorganic lead salt was added in the last stage of gelation to prepare the alcogels. The specimens were dried at room temperature to set then heated at 600 d eg C quickly to avoid crystallization preparing a glass containing 63 weight percent lead oxide. The influence of p H on absorption behavior of the sols studied by UV visible technique so the characteristic of the gel, alcogel and xerogel were studied in the different acidic concentrations. The UV spectrums show that the higher the acidity of the hydrolysis stages, the higher the absorbance. The results showed the sample with 63 weight percent lead was found fully amorphous. Microstructure and phase analysis of the glass powders were investigated by X-ray diffraction, X-ray fluorescence and scanning electron microscopy equipped with energy dispersive spectroscopy analysis

Active corrosion protection of AA2024 by sol-gel coatings with corrosion inhibitors =

Science.gov (United States)

Yasakau, Kiryl

industriais mostraram que estes novos revestimentos sao compativeis com os esquemas de pintura convencionais actualmente em uso. A estabilidade e o prazo de validade das formulacoes foram optimizados modificando a temperatura de armazenamento e a quantidade de agua usada durante a sintese. As formulacoes sol-gel foram dopadas com os inibidores seleccionados durante a primeira etapa e as propriedades anticorrosivas passivas e activas dos revestimentos obtidos foram estudadas numa terceira etapa do trabalho. Os resultados comprovam a influencia dos inibidores nas propriedades anticorrosivas dos revestimentos sol-gel. Em alguns casos a accao activa dos inibidores combinou-se com a proteccao passiva dada pelo revestimento mas noutros casos tera ocorrido interaccao quimica entre o inibidor e a matriz de sol-gel, de onde resultou a perda de propriedades protectoras do sistema combinado. Atendendo aos problemas provocados pela adicao directa dos inibidores na formulacao sol-gel procurou-se, numa quarta etapa, formas alternativas de incorporacao. Na primeira, produziu-se uma camada de titania nanoporosa na superficie da liga metalica que serviu de reservatorio para os inibidores. O revestimento sol-gel foi aplicado por cima da camada nanoporosa. Os inibidores armazenados nos poros actuam quando o substrato fica exposto ao ambiente agressivo. Numa segunda, os inibidores foram armazenados em nano-reservatorios de silica ou em nanoargilas (halloysite), os quais foram revestidos por polielectrolitos montados camada a camada. A terceira alternativa consistiu no uso de nano-fios de molibdato de cerio amorfo como inibidores anticorrosivos nanoparticulados. Os nano-reservatorios foram incorporados durante a sintese do sol-gel. Qualquer das abordagens permitiu eliminar o efeito negativo do inibidor sobre a estabilidade da matriz do sol-gel. Os revestimentos sol-gel desenvolvidos neste trabalho apresentaram proteccao anticorrosiva activa e capacidade de auto-reparacao. Os resultados obtidos

Fluorescence yield in rare-earth-doped sol-gel silicate glasses

Energy Technology Data Exchange (ETDEWEB)

Silversmith, A.J., E-mail: asilvers@hamilton.ed [Physics Department, Hamilton College, 198 College Hill Road, Clinton, NY 13323 (United States); Nguyen, Nguyen T.T.; Campbell, D.L. [Physics Department, Hamilton College, 198 College Hill Road, Clinton, NY 13323 (United States); Boye, D.M.; Ortiz, C.P. [Davidson College, Davidson, NC 28035 (United States); Hoffman, K.R. [Whitman College, Walla Walla, WA 99362 (United States)

2009-12-15

We have used trivalent terbium to investigate the mechanism behind fluorescence enhancement by Al{sup 3+} co-doping. Our results indicate that rare-earth (RE) ions cluster together in aluminum-rich regions of the glass, and behave as if they were dispersed uniformly throughout these regions when the ratio of Al to RE is {approx}10 or greater. We also studied the effects of adding chemical drying agents to the precursor solution for the synthesis of sol-gel-derived silicate glasses. Such glasses can be treated at significantly higher annealing temperatures without degradation of optical quality, and have the density of melt glass. Fluorescence yield from doped RE ions improves markedly with the addition of the drying agents, and the denser glasses are not subject to rehydration.

Una hermenéutica más de cara al debate sobre la valoración moral del aborto

Directory of Open Access Journals (Sweden)

Santiago Roldán García

2011-01-01

Full Text Available Desde una nueva lectura hermenéutica, se comprende desde la bioética que el tema sobre la inquietud moralmente valorativa frente a la terminación de un embarazo, no se encuentra enmarcada solamente en una perspectiva académica y ad intra de la misma. Se propone la inclusión y el análisis de otros factores y tipos de agentes implicados en el debate sobre la hominización y sus respectivas consecuencias valorativas en cuanto a lo ético y moral que, asumiendo la comprensión de la génesis del pensamiento, la tendencia de evolución del mismo y su innegable extensión, se proyecten a comprender muchos de los hechos, tanto empíricos como racionales con los que cuenta el ser humano para acercarse a una toma de decisiones al respecto.

Synthesis of uranium and thorium dioxides by Complex Sol-Gel Processes (CSGP). Synthesis of uranium oxides by Complex Sol-Gel Processes (CSGP)

International Nuclear Information System (INIS)

Deptula, A.; Brykala, M.; Lada, W.; Olczak, T.; Wawszczak, D.; Chmielewski, A.G.; Modolo, G.; Daniels, H.

2010-01-01

In the Institute of Nuclear Chemistry and Technology (INCT), a new method of synthesis of uranium and thorium dioxides by original variant of sol-gel method - Complex Sol-Gel Process (CSGP), has been elaborated. The main modification step is the formation of nitrate-ascorbate sols from components alkalized by aqueous ammonia. Those sols were gelled into: - irregularly agglomerates by evaporation of water; - medium sized microspheres (diameter <150) by IChTJ variant of sol-gel processes by water extraction from drops of emulsion sols in 2-ethylhexanol-1 by this solvent. Uranium dioxide was obtained by a reduction of gels with hydrogen at temperatures >700 deg. C, while thorium dioxide by a simple calcination in the air atmosphere. (authors)

Mesure de la vitesse d'infiltration des eaux dans le sol : Cas des sols ...

African Journals Online (AJOL)

C'est donc une infiltration superficielle qui ne peut pas modifier la composition des eaux de l'aquifère. Ces sols sont alors favorables à une telle agriculture. Mots clés: mesure, vitesse, infiltration, sols, pollutions, eau, Niari, Congo. English Title: Measuring the speed of the water infiltration into the soil: case of the soil of the ...

Effect of alumina sol addition to micro-arc oxidation electrolyte on the properties of MAO coatings formed on magnesium alloy AZ91D

International Nuclear Information System (INIS)

Laleh, M.; Rouhaghdam, A. Sabour; Shahrabi, T.; Shanghi, A.

2010-01-01

Oxide coatings were formed on AZ91D magnesium alloy using micro-arc oxidation process in alkaline electrolyte without and with addition of alumina sol. The microstructures and compositions of the MAO coatings were analyzed by scanning electron microscope (SEM) and X-ray diffraction (XRD). Corrosion behaviors of the coatings were evaluated with electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests in 3.5%NaCl solution. Porosities of the coatings were measured by potentiodynamic polarization tests. It was found that the coating produced in the electrolyte with alumina sol has more compact and uniform morphology than that produced in the electrolyte without alumina sol. The results of corrosion tests showed that the coating formed in electrolyte with alumina sol enhances the corrosion resistance of the substrate significantly. XRD patterns showed that the coating produced in the electrolyte with alumina sol has more MgAl 2 O 4 phase than MgO.

Análisis SIG Libre aplicado a Cooperación al Desarrollo. Reflexiones sobre datos de los agentes de cooperación en Galicia

OpenAIRE

Varela García, Francisco Alberto; Carballido Sanjurio, Roi; Puga Alonso, Francisco; Molejón Quintana, Carmen; Martínez Crespo, Gonzalo

2011-01-01

Presentación de una reflexión particular sobre la utilidad de emplear el SIG libre para trabajar en Cooperación al Desarrollo y para analizar las inversiones de la Administración Pública en este ámbito. Los planteamientos expuestos están basados en trabajos y experiencias vividas desde el Cartolab, tanto en participaciones en proyectos de cooperación, como en trabajos de análisis del uso de las tecnologías de la información geográfica en agentes de cooperación y un estudio sobre la inversión ...

Opportunity's Surroundings on Sol 1687

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a cylindrical projection with geometric seam correction.

Revisión de los estudios sobre exposición al aluminio y enfermedad de Alzheimer

Directory of Open Access Journals (Sweden)

Suay Llopis Loreto

2002-01-01

Full Text Available Se ha llevado a cabo una revisión bibliográfica de los estudios epidemiológicos que han evaluado el papel del aluminio como factor de riesgo para el desarrollo de la enfermedad de Alzheimer. Se realizó una búsqueda bibliográfica en la base de datos MedLine combinando los términos del Thesaurus "Aluminum" y "Alzheimer´s disease". En la mayor parte de los estudios revisados se ha examinado la exposición al metal a través del agua de bebida. Los estudios que sugieren que existe una asociación entre el aluminio y la enfermedad presentan riesgos relativos de alrededor de 2 para poblaciones con exposiciones a concentraciones de Al en el agua mayores de 0,1 mg/l. Las exposiciones al metal a través de otras vías (alimentación, medicamentos y exposición laboral han sido poco estudiadas. Estos estudios epidemiológicos presentan limitaciones metodológicas y sus resultados no son consistentes por lo que los resultados disponibles hasta el momento no permiten establecer, de manera clara, que exista una asociación entre la exposición al metal y la etiología de la enfermedad de Alzheimer. No obstante, tampoco es posible descartar un papel tóxico del aluminio sobre la salud, por lo que su exposición debería ser controlada y reducida en lo posible.

ANÁLISIS DEL EFECTO INMEDIATO Y DIFERIDO DE LA ORIENTACIÓN AL MERCADO SOBRE LOS RESULTADOS ORGANIZACIONALES. UN ESTUDIO LONGITUDINAL

Directory of Open Access Journals (Sweden)

Cauzo Bottala, Lourdes

2012-09-01

Full Text Available El objetivo del presente trabajo se centra en analizar el efecto, tanto inmediato como diferido, de la orientación al mercado (OM sobre los resultados organizacionales. Para ello, se ha realizado un estudio longitudinal, en un horizonte temporal de 3 años, en el sector financiero español. Respecto a la metodología, hemos desarrollado, de una parte, un método cualitativo con el fin de medir el grado de OM de las entidades consideradas, y ello a través de un análisis de contenido. Una vez obtenido un indicador de dicho análisis, hemos aplicado una metodología cuantitativa de ecuaciones estructurales, para contrastar las hipótesis del modelo propuesto. De los resultados obtenidos, destacamos, en primer lugar, que las entidades bancarias que implantan un enfoque de OM son propensas a mantener dicho enfoque en periodos sucesivos; en segundo término, que no se constatan efectos inmediatos de la OM sobre los resultados; y finalmente que la OM no registra efectos diferidos sobre aquellos indicadores de rentabilidad considerados.

Effects of parameters of sol-gel process on the phase evolution of sol-gel-derived hydroxyapatite

International Nuclear Information System (INIS)

Eshtiagh-Hosseini, Hossein; Housaindokht, Mohammad Reza; Chahkandi, Mohammad

2007-01-01

It has been established that hydroxyapatite powders can be produced using an alkoxide-based sol-gel technique. Nanocrystalline powders of hydroxyapatite (HA) were prepared from Ca(NO 3 ) 2 .4H 2 O and PO(OC 2 H 5 ) 3 as calcium and phosphorus precursors, respectively, using a sol-gel route. For a number of samples, sol of phosphorus was first hydrolyzed for 24 h with distilled water. The sol temperature, aging time and heat treatment temperature on apatite formation were systematically studied. Increasing the aging time affected the reducing of CaO. Also, increasing the mixed sol solution temperature up to 80 deg. C had a positive effect on the disappearance of impurity phases. With the increase of the calcination temperature >600 deg. C, calcium phosphate impurity phases disappeared. Structural evolution during the synthesis of hydroxyapatite is investigated by using infrared (IR) analysis, X-ray diffraction (XRD), thermal behavior (DTA), and elemental analysis of electron microscopy examination (SEM). X-ray diffraction with the aid of Scherrer and Williamson-Hall equations has been used to characterize the distributions of crystallite size and micro-strain of HA powders .The results indicated that mean crystallite size increased and micro-strain decreased significantly with the rise in firing temperature

Sol-gel synthesis and characterization of hybrid inorganic-organic Tb(III)-terephthalate containing layered double hydroxides

Science.gov (United States)

Smalenskaite, A.; Salak, A. N.; Ferreira, M. G. S.; Skaudzius, R.; Kareiva, A.

2018-06-01

Mg3/Al1 and Mg3Al1-xTbx layered double hydroxides (LDHs) intercalated with terephthalate anion were synthesized using sol-gel method. The obtained materials were characterized by X-ray diffraction (XRD) analysis, infrared (FTIR) spectroscopy, fluorescence spectroscopy (FLS) and scanning electron microscopy (SEM). The Tb3+ substitution effects in the Mg3Al1-xTbx LDHs were investigated by changing the Tb3+ concentration in the cation layers. The study indicates that the organic guest-terephthalate in the interlayer spacing of the LDH host influences the luminescence of the hybrid inorganic-organic materials.

Highly concentrated zinc oxide nanocrystals sol with strong blue emission

International Nuclear Information System (INIS)

Vafaee, M.; Sasani Ghamsari, M.; Radiman, S.

2011-01-01

Highly concentrated ZnO sol was synthesized by an improved sol-gel method. Water was used as a modifier to control the sol-gel reaction and provide a way to increase the sol concentration. Concentration of ZnO in the prepared sol is higher than from other methods. Optical absorption and photoluminescence were used to investigate optical properties of the prepared sol. FTIR test was performed to study the influence of water on the compounds of as-prepared sol. The size and morphology of ZnO nanoparticles have been studied by HRTEM. The prepared colloidal ZnO nanocrystals have narrow size distribution (5-8 nm) and showed strong blue emission. The prepared sol has enough potential for optoelectronic applications. - Research highlights: → Novel sol-gel route has been employed to prepare highly concentrated ZnO colloidal nanocrystals. → Water has been used to control the sources of emission in synthesized material. → A strong blue luminescent material has been obtained.

FACTORES AMBIENTALES Y GENÉTICOS QUE INFLUYEN SOBRE LA EDAD AL PRIMER PARTO EN HEMBRAS DE LA RAZA ROMOSINUANO

Directory of Open Access Journals (Sweden)

Marco Suárez

2006-05-01

Full Text Available Objetivo. Estudiar los factores ambientales y genéticos que influyen sobre la edad al primer parto dehembras romosinuano. Materiales y métodos. Fueron estudiados 932 datos de la edad al primer partode hembras de la raza Romosinuano, nacidas en el Centro de Investigación Turipaná de CORPOICA,Cereté, Colombia, en el período de 1980 a 2001. Para el estudio de los factores ambientales se utilizóel análisis de varianza mediante modelos lineales utilizando el procedimiento GLM de SAS (1995.Resultados. La edad al primer parto fue de 1162.3±4.2 días, con un coeficiente de variación del 11.19%.El análisis de varianza reveló que el año y mes de nacimiento fueron causas estadísticamente significativasde variación de la edad al primer parto. La heredabilidad, calculada por la correlación intraclase entremedias hermanas paternas fue de 0.16±0.08. Conclusión. El año y mes de nacimiento influyeron en laedad al primer parto de hembras romosinuano, pero la heredabilidad de la edad al primer parto y elsexo de la cría no se constituyen en características importantes a tener en cuenta.

The Sizing and Optimization Language, (SOL): Computer language for design problems

Science.gov (United States)

Lucas, Stephen H.; Scotti, Stephen J.

1988-01-01

The Sizing and Optimization Language, (SOL), a new high level, special purpose computer language was developed to expedite application of numerical optimization to design problems and to make the process less error prone. SOL utilizes the ADS optimization software and provides a clear, concise syntax for describing an optimization problem, the OPTIMIZE description, which closely parallels the mathematical description of the problem. SOL offers language statements which can be used to model a design mathematically, with subroutines or code logic, and with existing FORTRAN routines. In addition, SOL provides error checking and clear output of the optimization results. Because of these language features, SOL is best suited to model and optimize a design concept when the model consits of mathematical expressions written in SOL. For such cases, SOL's unique syntax and error checking can be fully utilized. SOL is presently available for DEC VAX/VMS systems. A SOL package is available which includes the SOL compiler, runtime library routines, and a SOL reference manual.

Catalisadores sol-gel de Ni-SiO2 e Ni-Al2O3 aplicados na reforma de metano com CO2 = Ni-SiO2 and Ni-Al2O3 sol-gel catalysts applied to methane reforming with CO2

Directory of Open Access Journals (Sweden)

Giane Gonçalves

2005-01-01

Full Text Available A reação de reforma do metano com CO2 apresenta-se como um processopromissor de geração de gás de síntese e hidrogênio. Neste sentido, foram preparados catalisadores de níquel-sílica e níquel-alumina pelo método sol-gel, com carga metálica nominal de 8% em massa. Os catalisadores foram caracterizados por redução à temperatura programada, análise termogravimétrica e determinação da área superficial específica. A reação de reforma do metano com CO2 foi realizada em um micro-reator contendo 500 mg de catalisador, previamente ativado em uma mistura redutora contendo hidrogênio. Osensaios de reforma a seco do metano foram realizados a 800°C, na pressão atmosférica, por um período de 12 horas, com uma razão molar de alimentação de [CO2:CH4] = 6. Os produtos da reação foram analisados por cromatografia gasosa. Dentre os catalisadoresavaliados, nas condições de reação estudadas, o catalisador de níquel suportado em sílica foi o que apresentou o melhor desempenho.The dry reforming reaction of methane comes as a promising process of syngas and hydrogen. Nickel catalysts on Al2O3 and SiO2 were synthesized by sol-gel method, with metalic load of 8% weight. The catalysts were characterized by temperature programmed reduction (TPR, termogravimetry analysis (TGA and specific surface area measurements (BET. The dry reforming reaction was performed in a micro reactor packed with 500 mg of catalyst, previously activated in atmosphere of hydrogen. The dry reforming tests were done at 800oC and atmospheric pressure by a period of 12 hours, with a molar ratio in the feeding of [CO2:CH4] = 6. The products of the reaction were analyzed by gas chromatograph. The Ni-SiO2 catalysts showed better performance.

RESISTENCIA A LA CORROSIÓN DE LAS MULTICAPAS DE [TIN/ALTIN]n DEPOSITADAS SOBRE ACERO AL CARBONO AISI 1045

Directory of Open Access Journals (Sweden)

WILLIAM APERADOR

2011-01-01

Full Text Available En este artículo se presenta el mejoramiento frente a la corrosión de los recubrimientos multicapas de [TiN/AlTiN]n con periodos de 2, 6, 12 y 24 bicapas depositados mediante la técnica de PVD magnetrón Sputtering sobre acero al carbono AISI 1045. La evaluación electroquímica se realizó mediante las técnicas espectroscopia de impedancia electroquímica (EIS y curvas de polarización Tafel, en una solución de 0.5M de H2SO4 + 3.5% wt. de NaCl. La resistencia a la corrosión aumentó de forma gradual en función del número de bicapas en comparación al sustrato encontrando valores de velocidad de corrosión de 18.51 mpy para el sustrato sin recubrir y de 1x10 6 mpy para la muestra con 24 bicapas. Los resultados electroquímicos revelan el efecto positivo en cuanto a la protección superficial del acero 1045 con el incremento del periodo en las multicapas de [TiN /AlTiN]n.

Modified silica sol coatings for surface enhancement of leather.

Science.gov (United States)

Mahltig, Boris; Vossebein, Lutz; Ehrmann, Andrea; Cheval, Nicolas; Fahmi, Amir

2012-06-01

The presented study reports on differently modified silica sols for coating applications on leather. Silica sols are prepared by acidic hydrolysis of tetraethoxysilane and modified by silane compounds with fluorinated and non-fluorinated alkylgroups. In contrast to many earlier investigations regarding sol-gel applications on leather, no acrylic resin is used together with the silica sols when applying on leather. The modified silica particles are supposed to aggregate after application, forming thus a modified silica coating on the leather substrate. Scanning electron microscopy investigation shows that the applied silica coatings do not fill up or close the pores of the leather substrate. However, even if the pores of the leather are not sealed by this sol-gel coating, an improvement of the water repellent and oil repellent properties of the leather substrates are observed. These improved properties of leather by application of modified silica sols can provide the opportunity to develop sol-gel products for leather materials present in daily life.

Efecto de las estrategias competitivas y los recursos y capacidades orientados al mercado sobre el crecimiento de las organizaciones

Directory of Open Access Journals (Sweden)

Carmen Berenice Ynzunza Cortés

2013-01-01

Full Text Available Este estudio analiza las relaciones entre las fuerzas de mercado, las estrategias competitivas, los recursos y capacidades orientados al mercado, así como el desempeño organizacional. La investigación se realizó en Pyme del sector industrial del estado de Querétaro, con un muestreo de conveniencia no probabilístico; asimismo, se diseñó un modelo estructural para probar las relaciones entre las variables, las cuales se analizaron con el software AMOS. El tamaño de muestra alcanzado fue de 116 y la recopilación de información se hizo mediante entrevistas. Las fuerzas de mercado, la estrategia competitiva y la orientación a mercado fueron medidas con las escalas de Kohly y Javorsky (1990, Segev (1987 y Narver y Slater (1990. Los ítems para el desempeño organizacional y los recursos de tecnología e innovación fueron diseñados. Los hallazgos prueban que las fuerzas de mercado tienen un impacto grande en la estrategia competitiva, el cual no es significativo sobre los recursos y capacidades, y es negativo respecto al desempeño, medido por el crecimiento organizacional. El efecto de la estrategia competitiva ha sido significativo sobre los recursos y capacidades de orientación a mercado, tecnología e innovación y no significativo respecto al desempeño. Estos recursos y capacidades influyen de manera significativa en el desempeño organizacional. Los resultados de este estudio enfatizan la implementación de estrategias prospectoras y analizadoras, que crean recursos y capacidades que den valor, con beneficios económicos para las empresas, así como los de orientación a mercado, tecnología e innovación. Estos hallazgos son consistentes con los encontrados en otras investigaciones realizadas en otros países.

¿Quién lo hizo? Datos sobre la investigación de delitos de sangre en al-Andalus

Directory of Open Access Journals (Sweden)

Marín, Manuela

2005-12-01

Full Text Available Two procedures of criminal investigation in al-Andalus are presented in this paper. First, the tadmiya, an accusation made by a seriously injured person against his or her assailant; secondly, the qasāma, an oath pronounced 50 times by the male relatives of a victim of murder accusing somebody of the crime. These two procedures are examined through several cases, historically documented, of their actual practice in al-Andalus. Jurists' opinions were not always unanimous on these issues, owing to differences in school affiliations (Mālikites against Shāfi'ites and to divergences inside the same school. Personal attitudes and social and economic relationships also played an important role in criminal investigations, as attested in the cases under study.

En este artículo se estudian dos aspectos de la investigación sobre delitos de sangre en al-Andalus. En primer lugar, la tadmiya, inculpación hecha por una persona gravemente herida contra su atacante. En segundo lugar, la qasāma, el juramento cincuentenario que podían hacer los parientes masculinos de la víctima de un crimen contra alguien a quien acusaban de haberlo cometido. Estos dos procedimientos se examinan a través de varios casos, documentados históricamente, en que se pusieron en práctica. Las opiniones de los juristas no siempre fueron unánimes a este respecto, bien por diferencias entre las escuelas legales (mālikíes y šāfi'íes, bien por divergencias dentro de la propia escuela mālikí. Tal como puede observarse en los casos estudiados, las actitudes personales, así como las relaciones sociales y económicas, representaron un papel importante en las investigaciones sobre los delitos de sangre.

Application of the docking program SOL for CSAR benchmark.

Science.gov (United States)

Sulimov, Alexey V; Kutov, Danil C; Oferkin, Igor V; Katkova, Ekaterina V; Sulimov, Vladimir B

2013-08-26

This paper is devoted to results obtained by the docking program SOL and the post-processing program DISCORE at the CSAR benchmark. SOL and DISCORE programs are described. SOL is the original docking program developed on the basis of the genetic algorithm, MMFF94 force field, rigid protein, precalculated energy grid including desolvation in the frame of simplified GB model, vdW, and electrostatic interactions and taking into account the ligand internal strain energy. An important SOL feature is the single- or multi-processor performance for up to hundreds of CPUs. DISCORE improves the binding energy scoring by the local energy optimization of the ligand docked pose and a simple linear regression on the base of available experimental data. The docking program SOL has demonstrated a good ability for correct ligand positioning in the active sites of the tested proteins in most cases of CSAR exercises. SOL and DISCORE have not demonstrated very exciting results on the protein-ligand binding free energy estimation. Nevertheless, for some target proteins, SOL and DISCORE were among the first in prediction of inhibition activity. Ways to improve SOL and DISCORE are discussed.

Sol-gel processing with inorganic metal salt precursors

Science.gov (United States)

Hu, Zhong-Cheng

2004-10-19

Methods for sol-gel processing that generally involve mixing together an inorganic metal salt, water, and a water miscible alcohol or other organic solvent, at room temperature with a macromolecular dispersant material, such as hydroxypropyl cellulose (HPC) added. The resulting homogenous solution is incubated at a desired temperature and time to result in a desired product. The methods enable production of high quality sols and gels at lower temperatures than standard methods. The methods enable production of nanosize sols from inorganic metal salts. The methods offer sol-gel processing from inorganic metal salts.

Electrophoretic deposition of sol-gel-derived ceramic coatings

International Nuclear Information System (INIS)

Zhang, Y.; Crooks, R.M.

1992-01-01

In this paper the physical, optical, and chemical characteristics of electrophoretically and dip-coated sol-gel ceramic films are compared. The results indicate that electrophoresis may allow a higher level of control over the chemistry and structure of ceramic coatings than dip-coating techniques. For example, controlled-thickness sol-gel coatings can be prepared by adjusting the deposition time or voltage. Additionally, electrophoretic coatings can be prepared in a four-component alumino-borosilicate sol display interesting optical characteristics. For example, the ellipsometrically-measured refractive indices of electrophoretic coatings are higher than the refractive indices of dip-coated films cast from identical sols, and they are also higher than any of the individual sol components. This result suggests that there are physical and/or chemical differences between films prepared by dip-coating and electrophoresis

Block Gas Sol Unit in Haderslev

DEFF Research Database (Denmark)

Vejen, Niels Kristian

2000-01-01

Investigation of a SDHW system based on a Block Gas Sol Unit from Baxi A/S installed by a consumer i Haderslev, Denmark.......Investigation of a SDHW system based on a Block Gas Sol Unit from Baxi A/S installed by a consumer i Haderslev, Denmark....

SolNet

DEFF Research Database (Denmark)

Jordan, Ulrike; Vajen, Klaus; Bales, Chris

2014-01-01

-accompanying Master courses, placements of internships, and PhD scholarship projects. A new scholarship project, “SHINE”, was launched in autumn 2013 in the frame work of the Marie Curie program of the European Union (Initial Training Network, ITN). 13 PhD-scholarships on solar district heating, solar heat......SolNet, founded in 2006, is the first coordinated International PhD education program on Solar Thermal Engineering. The SolNet network is coordinated by the Institute of Thermal Engineering at Kassel University, Germany. The network offers PhD courses on solar heating and cooling, conference...... for industrial processes, as well as sorption stores and materials started in December 2013. Additionally, the project comprises a training program with five PhD courses and several workshops on solar thermal engineering that will be open also for other PhD students working in the field. The research projects...

New Record Five-Wheel Drive, Spirit's Sol 1856

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this stereo, 180-degree view of the rover's surroundings during the 1,856th Martian day, or sol, of Spirit's surface mission (March 23, 2009). The center of the view is toward the west-southwest. The rover had driven 25.82 meters (84.7 feet) west-northwestward earlier on Sol 1856. This is the longest drive on Mars so far by a rover using only five wheels. Spirit lost the use of its right-front wheel in March 2006. Before Sol 1856, the farthest Spirit had covered in a single sol's five-wheel drive was 24.83 meters (81.5 feet), on Sol 1363 (Nov. 3, 2007). The Sol 1856 drive made progress on a route planned for taking Spirit around the western side of the low plateau called 'Home Plate.' A portion of the northwestern edge of Home Plate is prominent in the left quarter of this image, toward the south. This view is presented as a cylindrical projection with geometric seam correction.

Capacitación sobre lactancia materna al personal de enfermería del Hospital General de México

Directory of Open Access Journals (Sweden)

Hernández-Garduño Adolfo Gabriel

2000-01-01

Full Text Available OBJETIVO: Evaluar el cambio de conocimientos acerca de la lactancia entre el personal de enfermería del Hospital General de México que asistió a un curso teórico-práctico sobre lactancia materna de 18 horas de duración. MATERIAL Y MÉTODOS: Se realizó una intervención educativa sobre lactancia materna, con evaluación inicial y final, en el Hospital General de México, de mayo de 1996 a mayo de 1997. Se capacitó a 152 enfermeras. Se aplicó la prueba t de Student para muestras dependientes y análisis de varianza. RESULTADOS: De 152 participantes, 140 (92% respondieron ambas evaluaciones. Los resultados globales de la evaluación inicial y final fueron 5.39±1.37 y 7.74±0.79, respectivamente, y resultaron estadísticamente significativos (p<0.001. La significancia se mantuvo aun después de ajustar por el nivel de instrucción de los participantes. En la evaluación final se observó que a mayor nivel de escolaridad, mayores conocimientos sobre lactancia (p=0.004. CONCLUSIONES: Un curso de capacitación en lactancia de tipo teórico-práctico y de 18 horas de duración, dirigido al personal de enfermería, permite un cambio significativo en los conocimientos alcanzados.

Identification, expression, and immuno-reactivity of Sol i 2 & Sol i 4 venom proteins of queen red imported fire ants, Solenopsis invicta Buren (Hymenoptera: Formicidae).

Science.gov (United States)

Lockwood, Stephanie A; Haghipour-Peasley, Jilla; Hoffman, Donald R; Deslippe, Richard J

2012-10-01

We report on two low-molecular weight proteins that are stored in the venom of queen red imported fire ants (Solenopsis invicta). Translated amino acid sequences identified one protein to have 74.8% identity with the Sol i 2w worker allergen, and the other protein was found to have 96/97% identity with Sol i 4.01w/4.02w worker allergens. Both Sol i 2 and Sol i 4 queen and worker proteins were expressed using pEXP1-DEST vector in SHuffle™ T7 Express lysY Escherichia coli. Proteins were expressed at significant concentrations, as opposed to the μg/ml amounts by our previous expression methods, enabling further study of these proteins. Sol i 2q protein bound weakly to human IgE, sera pooled from allergic patients, whereas Sol i 2w, Sol i 4.01w, and Sol i 4q proteins bound strongly. Despite Sol i 2w and Sol i 2q proteins having 74.8% identity, the queen protein is less immuno-reactive than the worker allergen. This finding is consistent with allergic individuals being less sensitive to queen than worker venom. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of NaCl upon an Al-Si casting alloy hipoeutec; Efecto del NaCl sobre una aleacion de Al-Si hipoeutectica vaciada

Energy Technology Data Exchange (ETDEWEB)

Martinez Delgado, E.J.; Ortega de la Rosa, R. [Istituto Tecnologico de Zacatecas, Zacatecas (Mexico)]. E-mail: enriquemartinez_1999@yahoo.com; rubin_ortega_2002@yahoo.com.mx; Cisneros Guerrero, M.A. [Instituto Tecnologico de Saltillo, Saltillo, Coahuila (Mexico)]. E-mail: cisneros@its.mx; Haro Rodriguez, S. [Universidad Autonoma de Zacatecas, Zacatecas, Zacatecas (Mexico)]. E-mail: haros907@hotmail.com

2009-10-15

This work, comprehends the study about the effect of NaCl kind Halite upon the morphology of eutectic Silicon and porosity in a cast hipoeutectic Al-Si alloy. The melting was carried out in two furnaces, the first to combustion of LP gas in graphite crucible to increase the content of Si in the alloy from 0.13 to 5% wt using metallic silicon with a purity of 99.35% wt, and the second of electric resistances in the same kind of crucible to control the temperature at 750 degrees Celsius. The melting material was casting into molds of sand shell. To add the salt into the metallic bath, two techniques were used; one with injection by means of Argon gas and the other on by gravity, both cases three quantities of salt were used, 0.5, 1.5 and 2.5% wt respectively, powdered and preheated at 150 degrees Celsius during 60 min. The obtained samples were analyzed metallographily evidencing the modification of the eutectic Si, presenting the best results the samples with 1.5 and 2.5% wt of salt added by gravity. Too was obtained effect of Salt upon the degassing of bath metallic, where the simples with 1.5% wt presented the best results. Finally, by means of Scanning Electron Microscopy, the precipitates present were characterized in the samples. [Spanish] Este trabajo comprende el estudio del efecto del NaCl tipo Halita sobre la morfologia del Si eutectico y la porosidad en una aleacion fundida Al-Si hipoeutectica. La fusion se llevo a cabo en dos hornos, el primero a combustion con gas LP en crisol de grafito con la finalidad de incrementar el contenido de Si en la aleacion de 0.13 a 5% en peso, utilizando silicio metalico con una pureza de 99.35%, y el segundo de resistencias electricas en el mismo tipo de crisol para controlar la temperatura a 750 grados Celsios. El material fundido fue vaciado en modelos de arena. La sal se anadio al bano metalico a 0.5, 1.5 y 2.5% en peso, respectivamente, pulverizada y precalentada a 150 grados Celsios durante 60 min, mediante dos

Applications of sol gel ceramic coatings

International Nuclear Information System (INIS)

Barrow, D.

1996-01-01

The sol gel method is a chemical technique in which polycrystalline ceramic films are fabricated from a solution of organometallic precursors. The technique is attractive for many industrial applications because it is a simple (films are processed in air), flexible (can be used to coat complex geometries) and cost effective (does not require expensive equipment) process. In addition, dense, high quality coatings can be achieved at much lower temperatures than is generally required for sintering bulk ceramics. In this paper the conventional sol gel method and the new datec process are reviewed and potential applications of sol gel coatings in automotive, aerospace, petrochemical, nuclear and electronic industries are discussed. (orig.)

Sensitization by UV light of α-Al2O3:C polycrystalline detectors

International Nuclear Information System (INIS)

Meira B, L. C.; Rubio F, H.; Neres de A, E.; Santos, A.

2014-08-01

This paper describes an increase in sensitivity to gamma and beta radiation on α-Al 2 O 3 :C polycrystalline detector, which has been produced by a sol-gel process, following previous exposure to ultraviolet light. The increased sensitivity of the detector as a function of the exposure time and ultraviolet wavelength was studied. Since the main luminescent centers have emission peaks at different wavelengths, selective measurements of thermoluminescent emission intensity were done, in order to investigate the possible conversion of centers as a result of the exposition to ultraviolet light. Experimental results indicate that the nature and parameters of the luminescent centers in α-Al 2 O 3 :C sol-gel material can be very different of those in α-Al 2 O 3 :C single crystal. (author)

Modification of Ti6Al4V implant surfaces by biocompatible TiO{sub 2}/PCL hybrid layers prepared via sol-gel dip coating: Structural characterization, mechanical and corrosion behavior

Energy Technology Data Exchange (ETDEWEB)

Catauro, Michelina, E-mail: michelina.catauro@unina2.it [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 21, 81031 Aversa (Italy); Bollino, Flavia [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 21, 81031 Aversa (Italy); Giovanardi, Roberto; Veronesi, Paolo [Department of Engineering “Enzo Ferrari”, University of Modena and Reggio Emilia, Via Vivarelli 10, 41125 Modena (Italy)

2017-05-01

Surface modification of metallic implants is a promising strategy to improve tissue tolerance, osseointegration and corrosion resistance of them. In the present work, bioactive and biocompatible organic-inorganic hybrid coatings were prepared using a sol-gel dip coating route. They consist of an inorganic TiO{sub 2} matrix in which different percentages of poly(ε-caprolactone) (PCL), a biodegradable and biocompatible polymer, were incorporated. The coatings were used to modify the surface of Ti6Al4V substrates in order to improve their wear and corrosion resistance. The chemical structure of the coatings was analyzed by attenuated total reflectance (ATR) Fourier transform infrared (FTIR) spectroscopy. Coating microstructure, mechanical properties and ability to inhibit the corrosion of the substrates were evaluated as a function of the PCL amount. Scanning electron microscopy (SEM) showed that the polymer allows to obtain crack-free coatings, but when high percentages were added uncoated areas appear. Nano-indentation tests revealed that, as expected, surface hardness and elastic modulus decrease as the percentage of polymeric matrix increases, but scratch testing demonstrated that the coatings are effective in preventing scratching of the underlying metallic substrate, at least for PCL contents up to 20 wt%. The electrochemical tests (polarization curves acquired in order to evaluate the corrosion resistance) allowed to asses that the coatings have a significant effect in term of corrosion potential (E{sub corr}) but they do not significantly affect the passivation process that titanium undergoes in contact with the test solution used (modified Dulbecco's phosphate-buffered saline or DPBS). - Highlights: • Bioactive TiO{sub 2}/PCL hybrid coatings on Ti6Al4V were prepared via sol-gel dip coating. • Hybrid coatings are crack-free but when 50 wt% PCL was added, uncoated areas appear. • Coating hardness and elastic modulus decrease as the PCL percentage

Digging Movie from Phoenix's Sol 18

Science.gov (United States)

2008-01-01

The Surface Stereo Imager on NASA's Phoenix Mars Lander recorded the images combined into this movie of the lander's Robotic Arm enlarging and combining the two trenches informally named 'Dodo' (left) and 'Goldilocks.' The 21 images in this sequence were taken over a period of about 2 hours during Phoenix's Sol 18 (June 13, 2008), or the 18th Martian day since landing. The main purpose of the Sol 18 dig was to dig deeper for learning the depth of a hard underlying layer. A bright layer, possibly ice, was increasingly exposed as the digging progressed. Further digging and scraping in the combined Dodo-Goldilocks trench was planned for subsequent sols. The combined trench is about 20 centimeters (about 8 inches) wide. The depth at the end of the Sol 18 digging is 5 to 6 centimeters (about 2 inches). The Goldilocks trench was the source of soil samples 'Baby Bear' and 'Mama Bear,' which were collected on earlier sols and delivered to instruments on the lander deck. The Dodo trench was originally dug for practice in collecting and depositing soil samples. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Consideraciones sobre un nuevo y notable puñal calcolítico atribuible al grupo Treilles del Museu d´Arqueología de Catalunya en Barcelona

Directory of Open Access Journals (Sweden)

Rovira i Port, Jordi

2004-12-01

Full Text Available Althrough we were unaware of its concret origin, the Museu d´Arqueologia of Barcelona preserves in his collections a magnificent example of copper dagger assimilable to the series of daggers so-called «à encoche bilatérale » and «à soie courte crantée». These are pieces assimilated principally to the metallurgy of the pre-bell beakers of the Treilles Group, althrough certain pieces appear also in the prehistoric cultural groupes of Fontbuisse and Véraza. We present suggestions about its typology, filiation and the chronology of this dagger, as well as about its likely metallic composition.

Aunque ignoramos su procedencia concreta, el Museu d´Arqueologia de Barcelona conserva en sus colecciones un magnífico ejemplar de puñal de cobre tipológicamente atribuible a las series de puñales denominados genéricamente como «à encoche bilatérale» y «à soie courte crantée». Se trata de piezas asimilables mayoritariamente a la metalúrgia precampaniforme del Grupo «des Treilles», aunque ciertos ejemplares aparecen también en los grupos culturales prehistóricos franceses de Fontbuisse y Véraza. En el artículo se efectúan apreciaciones sobre su tipologia, la filiación y la datación del puñal, así como sobre su probable composición metalográfica.

Sol-gel synthesis of hydroxyapatite

International Nuclear Information System (INIS)

Zupanski, M.D.; Lucena, M.P.P.; Bergmann, C.P.

2010-01-01

Hydroxyapatite (HAp) has been established as the calcium phosphate based compound with most applications in the biological field. Among the numerous techniques for synthesis of HAp, the sol-gel processing route affords great control over purity and formed phases using low processing temperatures. In addition, the sol-gel approach offers an option for homogeneous HAp coating on metal substrates, as well as the ability to generate nanocrystalline powders. In this work, the sol-gel synthesis of HAp was investigated employing triethyl phosphate and calcium nitrate tetrahydrate as phosphorous and calcium precursors, respectively. The aging effect on phase composition and powder morphology of the final product was studied in terms of temperature and aging time. The powders were studied by using X-ray diffraction, Fourier transform infrared spectroscopy, particle size distribution by laser diffraction and scanning electron microscopy. (author)

Upgrades for TwinSol facility

Energy Technology Data Exchange (ETDEWEB)

O’Malley, P.D.; Bardayan, D.W.; Kolata, J.J.; Hall, M.R.; Hall, O.; Allen, J. [Physics Department, University of Notre Dame, Notre Dame, IN 46556 (United States); Becchetti, F.D. [Physics Department, U. Michigan, Ann Arbor MI 48109 (United States)

2016-06-01

TwinSol, a pair of coupled, superconducting solenoids, was one of the first devices capable of producing beams of radioactive nuclei at energies near the Coulomb barrier. A primary beam from University of Notre Dame (UND) tandem accelerator is used to bombard a primary target producing a secondary beam in flight. TwinSol is used to gather, separate, and focus the recoils. Since it was commissioned at the UND in 1997, at least 58 publications have reported data from its use and there have been hundreds of collaborators from many different countries that use this device. Currently, plans are in place at the UND to provide several upgrades to TwinSol, including a multi-cell gas production target and the possible addition of a third solenoid. Upgrades currently in progress will be discussed along with future plans.

Conocimiento sobre melanoma y prácticas de protección frente al sol en pacientes del Hospital Cullen de Santa Fe, Argentina Knowledge of melanoma and sun-protective practices in patients at José M. Cullen Hospital of Santa Fe, Argentine

Directory of Open Access Journals (Sweden)

A Loza

2011-09-01

Full Text Available Introducción. Melanoma es un cáncer de piel de mortalidad alta, cuya incidencia ha aumentado mundialmente en los últimos años. El siguiente estudio está destinado a detectar el conocimiento de la población sobre melanoma y las medidas de protección frente a la radiación UV (RUV, considerando que las dos terceras partes de los casos de melanoma se asocian al sol. Objetivo general. Detectar el conocimiento sobre melanoma y las prácticas de protección solar, en pacientes que consultan en el Servicio de Dermatología e internados en Clínica Médica del Hospital José M. Cullen. Materiales y métodos. Estudio observacional, prospectivo, longitudinal y descriptivo. La población abarcó 275 pacientes, entre 16 y 85 años, voluntarios del consultorio de Dermatología e internados en Clínica Médica del Hospital José M. Cullen. Mediante el programa Statistical Package for the Social Sciences 15.0, se realizó un análisis descriptivo y la prueba de Chi cuadrado, para determinar asociación estadística, entre variables cualitativas con significancia de pBackground. Melanoma is one of the deadliest forms of skin cancer, showing an increasing incidence worldwide over the past years. The aim of this study was to assess people's knowledge about melanoma, and their protective measures against UV radiation, considering that two-thirds of melanoma cases are associated to sun exposure. General objective. To assess the knowledge about melanoma and the sun protective practices in patients who attended the Department of Dermatology and in those admitted to the General Internal Medicine Unit of José M. Cullen Hospital. Material and methods. It was an observational, prospective, longitudinal, descriptive study. A sample of 275 participants aged between 16-85 years was included, composed of voluntary patients from the Department of Dermatology and inpatients from the General Internal Medicine Unit of José M. Cullen Hospital. The Statistical Package for

Contexto y pensamiento de Charles Taylor sobre el consenso

Directory of Open Access Journals (Sweden)

Doris Elena Ospina Muñoz

2017-01-01

Full Text Available El artículo sostiene que el consenso no es un tema de primer orden en la filosofía política de Charles Taylor, pero una lectura orientada al problema puede ofrecer los elementos para establecer una teoría sobre dicha noción e identificar los argumentos para su justificación. Además, se enfatiza en el contexto de discusión que permite introducir la filosofía de Taylor como un modo de pensar sobre el consenso, alternativo al constructivismo.

Fast Processing of Sol-Gel TCO

NARCIS (Netherlands)

Deelen, J. van; Rem, M.; Arfsten, N.; Buskens, P.P.

2016-01-01

TCOs are usually deposited using sputtering or chemical vapor deposition, which have a yield of typically 50-75%. The sol gel method does not need low pressure and can be done with a high precursor yield in the range of 90 – 100%. Sol gel enables also the TCO function as a planarization or

Sol-gel/drop-coated micro-thick TiO{sub 2} memristors for γ-ray sensing

Energy Technology Data Exchange (ETDEWEB)

Abunahla, Heba [Department of Electrical and Computer Engineering, Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates); Jaoude, Maguy Abi, E-mail: maguy.abijaoude@kustar.ac.ae [Department of Applied Mathematics and Sciences, Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates); O' Kelly, Curtis J.; Mohammad, Baker [Department of Electrical and Computer Engineering, Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2016-12-01

Sol-gel/drop-coated micro-thick TiO{sub 2} memristors were investigated and developed for low-power radiation sensing. Devices constructed with coated aluminum (Al) electrodes exhibited unipolar I-V characteristics with dynamic turn-on voltage, and progressive R{sub OFF}/R{sub ON} ratio loss under applied bias. Endurance failure of micro-thick Al/Al stacks is ascribed to gradual passivation of Al surface resulting from an electrically-enhanced oxygen-ion diffusion. By exchanging a single Al contact with higher work function copper (Cu) metal, two distinct superimposed TiO{sub 2} phases were formed. The TiO{sub 2} coating on Al surface was carbon-contaminated and amorphous, while that on Cu was found to be additionally doped with Cu{sup (I/II)} ions resulting from the corrosion of the surface of the electrode by the amine-based gelation agent. After initial forming, the hybrid stack could achieve a bipolar memristance, with high R{sub OFF}/R{sub ON} (up to 10{sup 6}), and over 10 switching cycles at low-operating voltages (±1 V). The enhanced memristive switching properties of Al/Cu devices are explained via cooperative valence-change/electrochemical-metallization processes, involving migration of oxygen and copper species. The advanced micro-thick TiO{sub 2} memristors were exposed to Cs-137 γ-rays, providing for the first time initial insights into their radiation detection capabilities. The sensing mechanism through these devices could be actuated by synergistic radiation-induced and field-driven photo-electric effects. - Highlights: • Micro-thick TiO{sub 2} memristors with Al or Cu electrodes are advanced via sol-gel drop-coating. • Memristive switching in Al/TiO{sub 2}/Al structure is not viable due to resistance build-up. • Drop-coated Cu electrode gets corroded by ethanolamine additive, introducing Cu{sup (I/II)} cations into bulk TiO{sub 2}. • Bipolar memristance in Al/TiO{sub 2}/Cu{sup (I/II)} doped-TiO{sub 2}/Cu structure is depicted for the

Opportunity's Surroundings on Sol 1687 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a vertical projection with geometric seam correction.

Opportunity's Surroundings on Sol 1687 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a polar projection with geometric seam correction.

Bioactive materials for biomedical applications using sol-gel technology

International Nuclear Information System (INIS)

Gupta, Radha; Kumar, Ashok

2008-01-01

This review paper focuses on the sol-gel technology that has been applied in many of the potential research areas and highlights the importance of sol-gel technology for preparing bioactive materials for biomedical applications. The versatility of sol-gel chemistry enables us to manipulate the characteristics of material required for particular applications. Sol-gel derived materials have proved to be good biomaterials for coating films and for the construction of super-paramagnetic nanoparticles, bioactive glasses and fiberoptic applicators for various biomedical applications. The introduction of the sol-gel route in a conventional method of preparing implants improves the mechanical strength, biocompatibility and bioactivity of scaffolds and prevents corrosion of metallic implants. The use of organically modified silanes (ORMOSILS) yields flexible and bioactive materials for soft and hard tissue replacement. A novel approach of nitric-oxide-releasing sol-gels as antibacterial coatings for reducing the infection around orthopedic implants has also been discussed

Sol-gel preparation of uranium oxide spheres

International Nuclear Information System (INIS)

Dolezal, J.; Urbanek, V.

1978-01-01

Information is presented on problems of preparing nuclear fuel by the sol-gel method. Basic data on different process types are given. A more detailed description of the method of preparation of spherical particles of uranium oxide gel developed and used at the Nuclear Research Institute at Rez is given. Advantages and disadvantages of sol-gel materials are discussed in comparison with fuel materials prepared by classical precipitation methods. The feasibility of the sol-gel methods for preparing other materials is shortly mentioned and their application outlined. (author)

L'educazione di un "Architetto-Urbanista". Manuel Solà-Morales e la Pedagogia Urbana all'ETSAB / The Education of an "Architect-Urbanist". Manuel Solà-Morales and Urban Pedagogy at the ETSAB

Directory of Open Access Journals (Sweden)

Marta Caldeira

2016-10-01

Full Text Available In qualità di docente, fondatore e direttore del Laboratori d’Urbanisme de Barcelona presso la ETSAB dal 1969 al 2012, l’architetto e urbanista spagnolo Manuel Solà-Morales ha curato la riforma chiave della pedagogia urbana della scuola di Barcellona. Deciso a superare la tendenza tecnocratica che aveva contraddistinto l’architettura e la pianificazione spagnola durante l’ultimo decennio del regime di Franco, l’obiettivo di Solà-Morales fu la formazione di quello che definì l’‘architetto-urbanista’ attraverso un programma propedeutico che accorpava architettura e urbanistica in un’unica disciplina. Sotto l’egida della morfologia urbana, il nuovo corso di Urbanistica impartito dal corpo docente del LUB diede il via allo studio della città e della sua storia come base principale di ogni progetto architettonico e urbano. / As professor and founding director of the Laboratori d’Urbanisme at the ETSAB from 1969 to 2012, Manuel Solà-Morales oversaw the pivotal reform of urban pedagogy in the Barcelona school. Determined to overcome the technocratic tendency that marked Spanish architecture and planning in the final decade of Franco’s regime, Solà-Morales’ mission was to educate what he defined as the ‘architect-urbanist’ through a foundational program that unified architecture and studies of urban form as a single discipline. Under the aegis of urban morphology, the new course of Urbanística taught by LUB’s team instituted the study of the city and its history as the primary ground for every architectural and urban project.

Current and future possibilities of sol-gel process

International Nuclear Information System (INIS)

Sakka, Sumio

2004-01-01

The sol-gel method is characterized by the low temperature processing. Since this method starts from solutions, the product is essentially nanomaterials. So far, various kinds of microstructures, including dense, porous, hybrid, amorphous and crystalline microstructures have been realized. Accordingly, sol-gel materials cover a wide range of functions, such as optical, electronic, mechanical, chemical and bio-functions. Future perspectives of the sol-gel method are described in the article. (author)

Sol-gel process for thermal reactor fuel fabrication

International Nuclear Information System (INIS)

Mukerjee, S.K.

2008-01-01

Full text: Sol-gel processes have revolutionized conventional ceramic technology by providing extremely fine and uniform powders for the fabrication of ceramics. The use of this technology for nuclear fuel fabrication has also been explored in many countries. Unlike the conventional sol-gel process, sol-gel process for nuclear fuels tries to eliminate the preparation of powders in view of the toxic nature of the powders particularly those of plutonium and 233 U. The elimination of powder handling thus makes this process more readily amenable for use in glove boxes or for remote handling. In this process, the first step is the preparation of microspheres of the fuel material from a solution which is then followed by vibro-compaction of these microspheres of different sizes to obtain the required smear density of fuel inside a pin. The maximum achievable packing density of 92 % makes it suitable for fast reactors only. With a view to extend the applicability of sol-gel process for thermal reactor fuel fabrication the concept of converting the gel microspheres derived from sol-gel process, to the pellets, has been under investigation for several years. The unique feature of this process is that it combines the advantages of sol-gel process for the preparation of fuel oxide gel microspheres of reproducible quality with proven irradiation behavior of the pellet fuel. One of the important pre-requisite for the success of this process is the preparation of soft oxide gel microspheres suitable for conversion to dense pellets free from berry structure. Studies on the internal gelation process, one of the many variants of sol-gel process, for obtaining soft oxide gel microspheres suitable for gel pelletisation is now under investigation at BARC. Some of the recent findings related to Sol-Gel Microsphere Pelletisation (SGMP) in urania-plutonia and thoria-urania systems will be presented

Analysis on the factors affecting the preparation of TIO2-ADUN composite sol by sol-gel method

International Nuclear Information System (INIS)

Wang Hui; Yin Rongcai; Liu Jinhong

2010-01-01

With C 2 H 2 O 5 and water as solvent and TBT as precursor and HNO 3 as the activator and valorize, the process for preparing TiO 2 -ADUN composite Sol method was studied. The influence of different reaction conditions on Sol-Gel time was analyzed in this study. The optimal reaction condition are: reaction temperature 20-25 degree C; pH value of reaction mixture 2-5; HNO 3 value of reaction mixture 0.3-0.5 ml; molar rations of alcohol to TBT 10, of water to TBT 2-3, respectively. A concentrated ADUN solution with Ti Sol , urea, water as additive is dispersed into uniform which are prepared by external mlii. (authors)

Ciudades y poder político en al-Andalus. Una hipótesis sobre el origen de las revueltas urbanas en Murcia en el siglo XIII

Directory of Open Access Journals (Sweden)

Frey Sánchez, Antonio Vicente

2014-12-01

Full Text Available Throughout the 13th century a succession of urban revolts took place in al-Andalus, which caused the withdrawal of the Almohad Empire and the establishment of the third taifas, initially led by Muhammad b. Yūsuf b. Hūd al-Mutawakkil. The inability of this emir to hold together this newly-built state, and the continuous insurrections inside and utside of Murcia have led historians to investigate the nature of political power during this period. This article examines each one of these proposals and, on the basis of an analysis of some socio-economic aspects relating to Murcia (being a representative city of al-Andalus and capital of the hūdí movement during the first half of the thirteenth century, proposes a hypothesis on the nature of its power.Durante el siglo XIII se produjo una serie de revueltas urbanas en al-Andalus que ocasionó la retirada del Imperio almohade y la formación de las terceras taifas, inicialmente encabezadas por Muḥammad b. Yūsuf b. Hūd al-Mutawakkil. La incapacidad de este emir para mantener unido el estado que había creado y las continuas insurrecciones fuera y dentro de Murcia ha llevado a historiadores y filólogos a indagar sobre la naturaleza del poder político en este periodo. Este artículo estudia cada una de estas interpretaciones y, a partir del análisis de algunos aspectos socio-económicos de Murcia, ciudad representativa en al-Andalus y capital del movimiento hūdí durante la primera mitad del siglo XIII, presenta una propuesta sobre la naturaleza de su poder.

Modeling SOL evolution during disruptions

International Nuclear Information System (INIS)

Rognlien, T.D.; Cohen, R.H.; Crotinger, J.A.

1996-01-01

We present the status of our models and transport simulations of the 2-D evolution of the scrape-off layer (SOL) during tokamak disruptions. This evolution is important for several reasons: It determines how the power from the core plasma is distributed on material surfaces, how impurities from those surfaces or from gas injection migrate back to the core region, and what are the properties of the SOL for carrying halo currents. We simulate this plasma in a time-dependent fashion using the SOL transport code UEDGE. This code models the SOL plasma using fluid equations of plasma density, parallel momentum (along the magnetic field), electron energy, ion energy, and neutral gas density. A multispecies model is used to follow the density of different charge-states of impurities. The parallel transport is classical but with kinetic modifications; these are presently treated by flux limits, but we have initiated more sophisticated models giving the correct long-mean-free path limit. The cross-field transport is anomalous, and one of the results of this work is to determine reasonable values to characterize disruptions. Our primary focus is on the initial thermal quench phase when most of the core energy is lost, but the total current is maintained. The impact of edge currents on the MHD equilibrium will be discussed

Sol-gel-based biosensing applied to medicinal science.

Science.gov (United States)

Moreira, Felismina T C; Moreira-Tavares, Ana P; Sales, M Goreti F

2015-01-01

Biosensors have opened new horizons in biomedical analysis, by ensuring increased assay speed and flexibility, and allowing point-of-care applications, multi-target analyses, automation and reduced costs of testing. This has been a result of many studies merging nanotechnology with biochemistry over the years, thereby enabling the creation of more suitable environments to biological receptors and their substitution by synthetic analogue materials. Sol-gel chemistry, among other materials, is deeply involved in this process. Sol-gel processing allows the immobilization of organic molecules, biomacromolecules and cells maintaining their properties and activities, permitting their integration into different transduction devices, of electrochemical or optical nature, for single or multiple analyses. Sol-gel also allows to the production of synthetic materials mimicking the activity of natural receptors, while bringing advantages, mostly in terms of cost and stability. Moreover, the biocompatibility of sol-gel materials structures of biological nature allowed the use of these materials in emerging in vivo applications. In this chapter, biosensors for biomedical applications based on sol-gel derived composites are presented, compared and described, along with current emerging applications in vivo, concerning drug delivery or biomaterials. Sol-gel materials are shown as a promising tool for current, emerging and future medical applications.

Structure/Property Relationships for Sol-gel Derived YBa2Cu3O7-d and SrTiO3 Films

Science.gov (United States)

Dawley, Jeff; Clem, Paul; Siegal, Michael; Overmyer, Don

2001-03-01

Solution deposition of c-axis oriented YBa2Cu3O7-d (YBCO) films on buffered RABiT substrates is a potential method for rapid, low cost production of superconducting tapes for power transmission and other applications. For this work, 100-250 nm thick YBCO and SrTiO3 (STO) films have been prepared by spin-coating and dip-coating sol-gel solutions onto LaAlO3 (100) and RABiT Ni (200) substrates. Biaxially textured STO coatings have been deposited on LaAlO3 and RABiT Ni by using a "templating" technique and controlling growth temperature and pO2. YBCO films grown on STO coated LaAlO3 possess comparable superconducting properties to YBCO films grown directly on LaAlO3 ( 1 MA/cm2 at 77K), indicating that a high quality STO layer does not degrade the crystalline quality of the YBCO. The effects of processing parameters on the STO buffer layer and novel processing techniques for decreasing the processing time and simplifying the integration of sol-gel YBCO with Ni substrates will be discussed. Sandia is a multiprogram laboratory operated by Sandia Corp., a Lockheed Martin Company, for the US Dept. Of Energy under contract DE-AC04-94A185000.

Silica Sol-Gel Entrapment of the Enzyme Chloro peroxidase

International Nuclear Information System (INIS)

Le, T.; Chan, S.; Ebaid, B.; Sommerhalter, M.

2015-01-01

The enzyme chloro peroxidase (CPO) was immobilized in silica sol-gel beads prepared from tetramethoxysilane. The average pore diameter of the silica host structure (∼3 nm) was smaller than the globular CPO diameter (∼6 nm) and the enzyme remained entrapped after sol-gel maturation. The catalytic performance of the entrapped enzyme was assessed via the pyrogallol peroxidation reaction. Sol-gel beads loaded with 4 μg CPO per mL sol solution reached 9-12% relative activity compared to free CPO in solution. Enzyme kinetic analysis revealed a decrease in K_cat but no changes in K_M or K_I . Product release or enzyme damage might thus limit catalytic performance. Yet circular dichroism and visible absorption spectra of transparent CPO sol-gel sheets did not indicate enzyme damage. Activity decline due to methanol exposure was shown to be reversible in solution. To improve catalytic performance the sol-gel protocol was modified. The incorporation of 5, 20, or 40% methyltrimethoxysilane resulted in more brittle sol-gel beads but the catalytic performance increased to 14% relative to free CPO in solution. The use of more acidic casting buffers (ph 4.5 or 5.5 instead of 6.5) resulted in a more porous silica host reaching up to 18% relative activity

Synthesis of phthalocyanine doped sol-gel materials

Science.gov (United States)

Dunn, Bruce

1993-01-01

The synthesis of sol-gel silica materials doped with three different types of metallophthalocyanines has been studied. Homogeneous materials of good optical quality were prepared and the first optical limiting measurements of dyes in sol-gel hosts were carried out. The properties of these solid state limiters are similar to limiters based on phthalocyanine (Pc) in solution. Sol-gel silica materials containing copper, tin and germanium phthalocyanines were investigated. The initial step in all cases was to prepare silica sols by the sonogel method using tetramethoxy silane (TMOS), HCl and distilled water. Thereafter, the synthesis depended upon the specific Pc and its solubility characteristics. Copper phthalocyanine tetrasulfonic acid tetra sodium salt (CuPc4S) is soluble in water and various doping levels (1 x 10 (exp -4) M to 1 x 10 (exp -5) M) were added to the sol. The group IV Pc's, SnPc(OSi(n-hexyl)3)2 and GePc(OSi(n-hexyl)3)2, are insoluble in water and the process was changed accordingly. In these cases, the compounds were dissolved in THF and then added to the sol. The Pc concentration in the sol was 2 x 10(exp -5)M. The samples were then aged and dried in the standard method of making xerogel monoliths. Comparative nanosecond optical limiting experiments were performed on silica xerogels that were doped with the different metallophthalocyanines. The ratio of the net excited state absorption cross section (sigma(sub e)) to the ground state cross section (sigma(sub g)) is an important figure of merit that is used to characterize these materials. By this standard the SnPc sample exhibits the best limiting for the Pc doped sol-gel materials. Its cross section ratio of 19 compares favorably with the value of 22 that was measured in toluene. The GePc materials appear to not be as useful as those containing SnPc. The GePc doped solids exhibit a higher onset energy (2.5 mj and lower cross section ratio, 7. The CuPc4S sol-gel material has a still lower cross

Sol-gel coatings on carbon/carbon composites

International Nuclear Information System (INIS)

Sim, S.M.; Krabill, R.M.; Dalzell, W.J. Jr.; Chu, P.Y.; Clark, D.E.

1986-01-01

The need for structural materials that can withstand severe environments up to 4000 0 F has promulgated the investigation of sol-gel derived ceramic and composite coatings on carbon/carbon composite materials. Alumina and zirconia sols have been deposited via thermophoresis on carbon/carbon substrates

Sol-gel applications for ceramic membrane preparation

Science.gov (United States)

Erdem, I.

2017-02-01

Ceramic membranes possessing superior properties compared to polymeric membranes are more durable under severe working conditions and therefore their service life is longer. The ceramic membranes are composed of some layers. The support is the layer composed of coarser ceramic structure and responsible for mechanical durability under filtration pressure and it is prepared by consolidation of ceramic powders. The top layer is composed of a finer ceramic micro-structure mainly responsible for the separation of components present in the fluid to be filtered and sol-gel method is a versatile tool to prepare such a tailor-made ceramic filtration structure with finer pores. Depending on the type of filtration (e.g. micro-filtration, ultra-filtration, nano-filtration) aiming separation of components with different sizes, sols with different particulate sizes should be prepared and consolidated with varying precursors and preparation conditions. The coating of sol on the support layer and heat treatment application to have a stable ceramic micro-structure are also important steps determining the final properties of the top layer. Sol-gel method with various controllable parameters (e.g. precursor type, sol formation kinetics, heat treatment conditions) is a practical tool for the preparation of top layers of ceramic composite membranes with desired physicochemical properties.

Consideraciones del bioderecho sobre la eutanasia en Colombia

Directory of Open Access Journals (Sweden)

José Antonio García Pereáñez

2017-01-01

Full Text Available Este artículo aborda de manera reflexiva las incidencias del bioderecho sobre situaciones de eutanasia en Colombia, al interpretar conflictos morales y jurídicos suscitados por las sentencias de la Corte Constitucional C239 de 1997, T970 de 2014 y la Resolución del Ministerio de Salud y Protección Social 1216, de 2015. El propósito fundamental es el análisis de las decisiones judiciales sobre el final de la vida humana. Por lo tanto, se realiza una revisión de la construcción histórica y jurídica del concepto de eutanasia y se propone la discusión sobre su manejo jurídico y su influencia en el colectivo moral. Asimismo, se diserta sobre el concepto de dignidad humana y muerte digna, como precedentes para dirimir los conflictos éticos que la eutanasia suscita. Al final, se analiza el caso de don Ovidio González, quien se convirtió en 2015 en el primer colombiano en recibir la eutanasia de manera legal dentro del sistema de salud.

Sol-gel optical coatings for lasers: Part 1

International Nuclear Information System (INIS)

Floch, H.G.; Belleville, P.F.; Priotton, J.J.

1995-01-01

Many manufacturers and users claim that optical coatings are best prepared by physical vapor deposition technology. Others believe that sol-gel technology is an effective and competitive alternative. This article, the first of three, emphasizes sol-gel thin-film history and relates it to high-power laser technology, chemistry of the sol-gel process, production of optical coatings and deposition techniques. The second and third articles describe the preparation and performance of antireflective and highly reflective sol-gel optical coatings, respectively, that have been developed for the 1.8-MJ/500-TW (351-nm) pulsed neodymium-glass laser. This powerful laser is to be used in France's Inertial Confinement Fusion (ICF) program. It will demonstrate, at the laboratory scale, ignition of deuterium-tritium fusion fuel

Self-Healing Corrosion Protective Sol-Gel Coatings

NARCIS (Netherlands)

Abdolah Zadeh, M.

2016-01-01

Inspired by the state of the art and the recent advances in the field of self-healing corrosion protective coatings, the thesis entitled “Self-healing corrosion protective sol-gel coatings” addresses novel routes to self-healing corrosion protective sol-gel coatings via extrinsic and intrinsic

Screen-printable sol-gel enzyme-containing carbon inks.

Science.gov (United States)

Wang, J; Pamidi, P V; Park, D S

1996-08-01

Enzymes usually cannot withstand the high-temperature curing associated with the thick-film fabrication process and require a separate immobilization step in connection with the production of single-use biosensors. We report on the development of sol-gel-derived enzyme-containing carbon inks that display compatibility with the screen-printing process. Such coupling of sol-gel and thick-film technologies offers a one-step fabrication of disposable enzyme electrodes, as it obviates the need for thermal curing. The enzyme-containing sol-gel carbon ink, prepared by dispersing the biocatalyst, along with the graphite powder and a binder, within the sol-gel precursors, is cured very rapidly (10 min) at low temperature (4 °C). The influence of the ink preparation conditions is explored, and the sensor performance is evaluated in connection with the incorporation of glucose oxidase or horseradish peroxidase. The resulting strips are stable for at least 3 months. Such sol-gel-derived carbon inks should serve as hosts for other heat-sensitive biomaterials in connection with the microfabrication of various thick-film biosensors.

Sol-gel based oxidation catalyst and coating system using same

Science.gov (United States)

Watkins, Anthony N. (Inventor); Leighty, Bradley D. (Inventor); Oglesby, Donald M. (Inventor); Patry, JoAnne L. (Inventor); Schryer, Jacqueline L. (Inventor)

2010-01-01

An oxidation catalyst system is formed by particles of an oxidation catalyst dispersed in a porous sol-gel binder. The oxidation catalyst system can be applied by brush or spray painting while the sol-gel binder is in its sol state.

Fast temperature fluctuation measurements in SOL of tokamak TCV

DEFF Research Database (Denmark)

Horacek, J.; Nielsen, Anders Henry; Pitts, R.A.

to compare the statistical character of turbulence in the SOL particle flux on TCV with results from the 2D fluid electrostatic model ESEL [2][4]. Using results from the fast sweeping, similar comparisons can now be made with the fluctuating Te and will be described in this contribution. We also present...... basic statistics derived from the Te time series obtained at different radii in the SOL plasma and show, in particular, that the relationship between higher moments of the probability distribution function from both experimental and simulated Te’s may be well described by the Beta probability...... distribution function, introduced for SOL turbulence in [5]. The fast Te capability also allows the SOL response to Edge Localised Modes (ELMs) to be studied and new results will be presented for the far SOL Te response during Type III ELMs....

Sensitization by UV light of α-Al{sub 2}O{sub 3}:C polycrystalline detectors

Energy Technology Data Exchange (ETDEWEB)

Meira B, L. C.; Rubio F, H.; Neres de A, E. [Centro de Desenvolvimento da Tecnologia Nuclear - CNEN, Laboratorio de Dosimetria Termoluminicente, Av. Antonio Carlos 6627, Campus UFMG, CEP 31270-901, Belo Horizonte (Brazil); Santos, A., E-mail: hrf@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear - CNEN, Laboratorio de Microesferas Gel, Av. Antonio Carlos 6627, Campus UFMG, CEP 31270-901, Belo Horizonte (Brazil)

2014-08-15

This paper describes an increase in sensitivity to gamma and beta radiation on α-Al{sub 2}O{sub 3}:C polycrystalline detector, which has been produced by a sol-gel process, following previous exposure to ultraviolet light. The increased sensitivity of the detector as a function of the exposure time and ultraviolet wavelength was studied. Since the main luminescent centers have emission peaks at different wavelengths, selective measurements of thermoluminescent emission intensity were done, in order to investigate the possible conversion of centers as a result of the exposition to ultraviolet light. Experimental results indicate that the nature and parameters of the luminescent centers in α-Al{sub 2}O{sub 3}:C sol-gel material can be very different of those in α-Al{sub 2}O{sub 3}:C single crystal. (author)

New insights into uranium (VI) sol-gel processing

International Nuclear Information System (INIS)

King, C.M.; Thompson, M.C.; Buchanan, B.R.; King, R.B.; Garber, A.R.

1990-01-01

Nuclear Magnetic Resonance (NMR) investigations on the Oak Ridge National Laboratory process for sol-gel synthesis of microspherical nuclear fuel (UO 2 ), has been extremely useful in sorting out the chemical mechanism in the sol-gel steps. 13 C, 15 N, and 1 H NMR studies on the HMTA gelation agent (Hexamethylene tetramine, C 6 H 12 N 4 ) has revealed near quantitative stability of this adamantane-like compound in the sol-gel process, contrary to its historical role as an ammonia source for gelation from the worldwide technical literature. 17 O NMR of uranyl (UO 2 ++ ) hydrolysis fragments produced in colloidal sols has revealed the selective formation of a uranyl trimer, [(UO 2 ) 3 (μ 3 -O)(μ 2 -OH) 3 ] + , induced by basic hydrolysis with the HMTA gelation agent. Spectroscopic results will be presented to illustrate that trimer condensation occurs during sol-gel processing leading to layered polyanionic hydrous uranium oxides in which HMTAH + is occluded as an ''intercalation'' cation. Subsequent sol-gel processing of microspheres by ammonia washing results in in-situ exchange and formation of a layered hydrous ammonium uranate with a proposed structural formula of (NH 4 ) 2 [(UO 2 ) 8 O 4 (OH) 10 ] · 8H 2 O. This compound is the precursor to sintered UO 2 ceramic fuel. 23 refs., 10 figs

[Basic Studies on Locoregional Injection of a Newly Designed Chitin Sol].

Science.gov (United States)

Chiba, Takehiro; Sugitachi, Akio; Kume, Kouhei; Segawa, Takenori; Nishinari, Yutaka; Ishida, Kaoru; Noda, Hironobu; Nishizuka, Satoshi; Kimura, Yusuke; Koeda, Keisuke; Sasaki, Akira

2015-11-01

Systemic chemotherapy in advanced cancer cases often provokes serious adverse events. We aimed to examine the fundamental properties and efficacy of a novel chitin sol, an anti-cancer agent with minor side effects designed to avoid the adverse effects of chemotherapy and enhance the QOL and ADL of patients. DAC-70 was used to create the novel agent termed DAC-70 sol. The anti-proliferative activity was assayed by the WST method using different types of cell lines. The anti-cancer efficacy of the novel agent was examined using cancer-bearing mice. DAC-70 sol was easily injectable through a 21-G needle. The sol suppressed proliferation of the cells in vitro. Intra-tumor injection of DAC-70 sol inhibited the rapid growth of solid tumors in the mice. CDDP-loaded DAC-70 sol, CDDP/DAC-70 sol, successfully controlled malignant ascites in the mice (psol and CDDP/DAC-70 sol is clinically useful as novel cancer chemotherapy for advanced cases. This warrants further clinical studies in cancer chemotherapy.

Cinco puntos sobre la revista Barcelona

OpenAIRE

Bertone Crippa, Mauro

2012-01-01

El humor, como género y narrativa mediática, ocupa un lugar destacado al interior del campo del periodismo gráfico argentino. Como emergente contemporáneo dentro de este ámbito, la revista Barcelona se vuelve un objeto de estudio sugestivo al trabajar, a partir del registro del humor, sobre la agenda y la enunciación de los medios gráficos de actualidad. De esta manera, se analizan las condiciones de producción del discurso de Barcelona para ver qué novedades aporta al campo del hu...

Vanadium dioxide formed by the sol-gel process

International Nuclear Information System (INIS)

Potember, R.S.; Speck, K.R.; Hu, H.S.

1990-01-01

This patent describes a process for the deposition of a crystalline vanadium dioxide thin film. It comprises: providing a solution comprising a vanadium tetraalkoxide and solvent; allowing hydrolysis and condensation reactions to progressively form a homogeneous sol from the solution, applying a coating of the sol to the substrate; allowing a gel to form from the sol on the substrate by evaporating the solvent; dehydrating the gel by heat treatment under an inert atmosphere to form the crystalline vanadium dioxide film

Silica scintillating materials prepared by sol-gel methods

International Nuclear Information System (INIS)

Werst, D.W.; Sauer, M.C. Jr.; Cromack, K.R.; Lin, Y.; Tartakovsky, E.A.; Trifunac, A.D.

1993-01-01

Silica was investigated as a rad-hard alternative to organic polymer hosts for organic scintillators. Silica sol-gels were prepared by hydrolysis of tetramethoxysilane in alcohol solutions. organic dyes were incorporated into the gels by dissolving in methanol at the sol stage of gel formation. The silica sol-gel matrix is very rad-hard. The radiation stability of silica scintillators prepared by this method is dye-limited. Transient radioluminescence was measured following excitation with 30 ps pulses of 20 MeV electrons

Notas sobre Matisia longiflora Gleas. (Bombacaceae Notas sobre Matisia longiflora Gleas. (Bombacaceae

Directory of Open Access Journals (Sweden)

Fernández Alonso José Luis

1992-09-01

Full Text Available Dentro del grupo de géneros de bombacáceas de hojas simples que componen la tribu Quararibeae (= Matisieae Hutchinson, es Matisia Humb. & Bonpl. el que cuenta con mayor número de especies en Colombia. Al respecto se presentaron recientemente algunas consideraciones preliminares sobre la diversidad de especies en este grupo en Colombia (Fernández Alonso, 1991.

Fluorescence of Pentavalent Chromium in SiO2 Sol-Gel Glasses

Science.gov (United States)

Jia, Weiyi; Castro, Lymari; Wang, Yanyun; Liu, Huimin

1998-01-01

Chromium ions are very attractive to optical spectroscopy and laser physics. It is well known that the first laser in the history is a ruby laser activated with Cr(3+). It was found in early nineties that Cr(4+) was also an interesting lasing ion in the near infrared, and various Cr(4+) lasers have been developed. Very recently, it was reported that Cr(2+) doped in CdSe crystals showed lasing action in the infrared. The above achievement have stimulated an interest in searching for Cr(5+) and investigating its optical properties. Cr(5+) is isoelectronic with Ti(3+) and V(4+), having electron configuration 3d1. Ti(3+) is the active center of commercial cw and femtosecond sapphire lasers, tunable in the range 680-1100 nm. V(4+) doped in YAlO3 and Al2O3 showed broad band emission near 635 nm. Although EPR results of Cr(5+) were reported, the optical properties were less studied. Herren et al. reported an observation of luminescence from Cr doped in SiO2 sol-gel glass. The luminescence spectrum was assigned to pentavalent ions in their first paper, and later it was identified to be the emission from the charge transfer transition of Cr(6+). The first observation of photoluminescence from octahedrally coordinated Cr(5+) in BaCaMg aluminate glasses was reported very recently. In this work, we report luminescence results of Cr doped SiO2 sol-gel glasses. The fluorescence spectra are very different from Herrens' results, and we believe it originates from pentavalent Cr.

La microflore des sols du vignoble de Touraine

Directory of Open Access Journals (Sweden)

Claude Cuinier

1975-12-01

Full Text Available L'étude microbiologique des sols du vignoble porte sur trois années. Les déterminations quantitatives des bactéries, champignons, actinomycètes et des groupes fonctionnels des cycles de l'azote, du carbone et du soufre sont effectuées au cours de trois périodes du cycle végétatif de la vigne. Des variations saisonnières et annuelles sont observées. La microflore des sols viticoles est comparée à celle d'autres sols. Elle est au moins aussi riche et se distingue par son caractère plus aérobie. De grands écarts dans la composition microbiologique sont apparus entre des sols viticoles différant par leurs caractéristiques physiques et chimiques.

Turbulent transport regimes and the SOL heat flux width

Science.gov (United States)

Myra, J. R.; D'Ippolito, D. A.; Russell, D. A.

2014-10-01

Understanding the responsible mechanisms and resulting scaling of the scrape-off layer (SOL) heat flux width is important for predicting viable operating regimes in future tokamaks, and for seeking possible mitigation schemes. Simulation and theory results using reduced edge/SOL turbulence models have produced SOL widths and scalings in reasonable accord with experiments in many cases. In this work, we attempt to qualitatively and conceptually understand various regimes of edge/SOL turbulence and the role of turbulent transport in establishing the SOL heat flux width. Relevant considerations include the type and spectral characteristics of underlying instabilities, the location of the gradient drive relative to the SOL, the nonlinear saturation mechanism, and the parallel heat transport regime. Recent SOLT turbulence code results are employed to understand the roles of these considerations and to develop analytical scalings. We find a heat flux width scaling with major radius R that is generally positive, consistent with older results reviewed in. The possible relationship of turbulence mechanisms to the heuristic drift mechanism is considered, together with implications for future experiments. Work supported by US DOE grant DE-FG02-97ER54392.

Effect of thickness on structural, electrical, optical and magnetic properties of Co and Al doped ZnO films deposited by sol-gel route

Energy Technology Data Exchange (ETDEWEB)

Sharma, Mamta [Department of Electronic Science, University of Delhi South Campus, New Delhi 110021 (India); Mehra, R.M. [Department of Electronic Science, University of Delhi South Campus, New Delhi 110021 (India)], E-mail: rammehra2003@yahoo.com

2008-12-30

This paper reports deposition and characterization of Zn{sub 0.94}Co{sub 0.05}Al{sub 0.01}O films of thickness ranging from 70 nm to 400 nm. These films were deposited on a glass (Corning, 7059) substrate using sol-gel route. The films have been characterized to study their structural, electrical, optical and magnetic properties. X-ray diffraction (XRD) and atomic force microscopy (AFM) were used to study the crystallinity and growth mode of the films. The films deposited up to a thickness of 200 nm showed improvement in crystallinity and preferential c-axis orientation. A transition in the growth mode from vertical (c-axis) to lateral (a and b-axis) was observed with further increase in the thickness of the film. The average transmittance of the films for thickness less than 200 nm was above 80% in the visible region which decreased at higher thickness of the film. The resistivity of the film was found to decrease with increase in thickness up to 200 nm. Ferromagnetism, at room temperature, was confirmed for 200 nm and 400 nm thick films.

Effect of thickness on structural, electrical, optical and magnetic properties of Co and Al doped ZnO films deposited by sol-gel route

International Nuclear Information System (INIS)

Sharma, Mamta; Mehra, R.M.

2008-01-01

This paper reports deposition and characterization of Zn 0.94 Co 0.05 Al 0.01 O films of thickness ranging from 70 nm to 400 nm. These films were deposited on a glass (Corning, 7059) substrate using sol-gel route. The films have been characterized to study their structural, electrical, optical and magnetic properties. X-ray diffraction (XRD) and atomic force microscopy (AFM) were used to study the crystallinity and growth mode of the films. The films deposited up to a thickness of 200 nm showed improvement in crystallinity and preferential c-axis orientation. A transition in the growth mode from vertical (c-axis) to lateral (a and b-axis) was observed with further increase in the thickness of the film. The average transmittance of the films for thickness less than 200 nm was above 80% in the visible region which decreased at higher thickness of the film. The resistivity of the film was found to decrease with increase in thickness up to 200 nm. Ferromagnetism, at room temperature, was confirmed for 200 nm and 400 nm thick films.

Structure changes in the sol-gel systems of hydrated oxides

International Nuclear Information System (INIS)

Gaponov, Y.A.; Karakchiev, L.G.; Lyakhov, N.Z.; Tolochko, B.P.; Ito, K.; Amemiya, Y.

1998-01-01

Sols of hydrated aluminium oxide, hydrated zirconium oxide and their mixtures were investigated during the xerogel-amorphous-product-crystalline-product transition by SAXS using synchrotron radiation. In the different temperature regions certain changes in structure and morphology were observed. Some correlation between the characteristics of the initial sols and their mixtures (the size and shape of the pores) was observed. In the temperature region 298-1173 K the characteristics of the mixed sol are defined by the characteristics of the initial sols

Biocatalysis with Sol-Gel Encapsulated Acid Phosphatase

Science.gov (United States)

Kulkarni, Suhasini; Tran, Vu; Ho, Maggie K.-M.; Phan, Chieu; Chin, Elizabeth; Wemmer, Zeke; Sommerhalter, Monika

2010-01-01

This experiment was performed in an upper-level undergraduate biochemistry laboratory course. Students learned how to immobilize an enzyme in a sol-gel matrix and how to perform and evaluate enzyme-activity measurements. The enzyme acid phosphatase (APase) from wheat germ was encapsulated in sol-gel beads that were prepared from the precursor…

Sol-gel synthesis of 45S5 bioglass – Prosthetic coating by electrophoretic deposition

Directory of Open Access Journals (Sweden)

Faure Joel

2013-11-01

Full Text Available In this work, the 45S5 bioactive glass has been prepared by the sol-gel process using an organic acid catalyst instead of nitric acid usually used. The physico-chemical and structural characterizations confirmed and validated the elemental composition of the resulting glass. In addition, the 45S5 bioactive glass powder thus obtained was successfully used to elaborate by electrophoretic deposition a prosthetic coating on titanium alloy Ti6Al4V.

Preparation and characterization of sol-gel derived TiO2 films

International Nuclear Information System (INIS)

Hong, Y.J.; Brungs, M.P.; Chaplin, R.P.; Sizgek, E.

2001-01-01

Crack-free transparent titania films have been prepared through a new sol-gel process combined with hydrogen peroxide treatment. Hydrogen peroxide and HCl were used to dissolve amorphous titania powder which is obtained by drying common sol-gel titania sol. The peroxo-titania sol produced a thicker film than the common sol-gel titania sol due to a higher degree of condensation. Film thickness could be further increased by controlled drying conditions of the amorphous titania powder or 'aging' the sol. Polyethylene glycol (PEG) and chemical additives were effective in controlling condensation rate by preventing rapid condensation during curing of the film. When these two components were incorporated, it was possible to create a 0.5μm transparent film and PEG could also control the porosity of the film. The cured film was analysed by XRD and Raman spectroscopy. In order to measure the reflective index and thickness of the titania film, an ellipsometer was used. Copyright (2001) The Australian Ceramic Society

Silica- and germania-based dual-ligand sol-gel organic-inorganic hybrid sorbents combining superhydrophobicity and π-π interaction. The role of inorganic substrate in sol-gel capillary microextraction.

Science.gov (United States)

Seyyal, Emre; Malik, Abdul

2017-04-29

Principles of sol-gel chemistry were utilized to create silica- and germania-based dual-ligand surface-bonded sol-gel coatings providing enhanced performance in capillary microextraction (CME) through a combination of ligand superhydrophobicity and π-π interaction. These organic-inorganic hybrid coatings were prepared using sol-gel precursors with bonded perfluorododecyl (PF-C 12 ) and phenethyl (PhE) ligands. Here, the ability of the PF-C 12 ligand to provide enhanced hydrophobic interaction was advantageously combined with π-π interaction capability of the PhE moiety to attain the desired sorbent performance in CME. The effect of the inorganic sorbent component on microextraction performance of was explored by comparing microextraction characteristics of silica- and germania-based sol-gel sorbents. The germania-based dual-ligand sol-gel sorbent demonstrated superior CME performance compared to its silica-based counterpart. Thermogravimetric analysis (TGA) of the created silica- and germania-based dual-ligand sol-gel sorbents suggested higher carbon loading on the germania-based sorbent. This might be indicative of more effective condensation of the organic ligand-bearing sol-gel-active chemical species to the germania-based sol-gel network (than to its silica-based counterpart) evolving in the sol solution. The type and concentration of the organic ligands were varied in the sol-gel sorbents to fine-tune extraction selectivity toward different classes of analytes. Specific extraction (SE) values were used for an objective comparison of the prepared sol-gel CME sorbents. The sorbents with higher content of PF-C 12 showed remarkable affinity for aliphatic hydrocarbons. Compared to their single-ligand sol-gel counterparts, the dual-ligand sol-gel coatings demonstrated significantly superior CME performance in the extraction of alkylbenzenes, providing up to ∼65.0% higher SE values. The prepared sol-gel CME coatings provided low ng L -1 limit of detections (LOD

Sol-Gel Manufactured Energetic Materials

Science.gov (United States)

Simpson, Randall L.; Lee, Ronald S.; Tillotson, Thomas M.; Hrubesh, Lawrence W.; Swansiger, Rosalind W.; Fox, Glenn A.

2005-05-17

Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

Spatially resolved speckle-correlometry of sol-gel transition

Science.gov (United States)

Isaeva, A. A.; Isaeva, E. A.; Pantyukov, A. V.; Zimnyakov, D. A.

2018-04-01

Sol-gel transition was studied using the speckle correlometry method with a localized light source and spatial filtering of backscattered radiation. Water solutions of technical or food gelatin with added TiO2 nanoparticles were used as studied objects. Structural transformation of "sol-gel" system was studied at various temperatures from 25°C to 50°C using analysis of the correlation and structure functions of speckle intensity fluctuations. The characteristic temperatures of "sol - gel" transition were evaluated for studied systems. Obtained results can be used for various applications in biomedicine and food industry.

Time for a Change; Spirit's View on Sol 1843

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this full-circle view of the rover's surroundings during the 1,843rd Martian day, or sol, of Spirit's surface mission (March 10, 2009). South is in the middle. North is at both ends. The rover had driven 36 centimeters downhill earlier on Sol 1854, but had not been able to get free of ruts in soft material that had become an obstacle to getting around the northeastern corner of the low plateau called 'Home Plate.' The Sol 1854 drive, following two others in the preceding four sols that also achieved little progress in the soft ground, prompted the rover team to switch to a plan of getting around Home Plate counterclockwise, instead of clockwise. The drive direction in subsequent sols was westward past the northern edge of Home Plate. This view is presented as a cylindrical projection with geometric seam correction.

Effect of SiO2 concentration in silica sol on interface reaction during titanium alloy investment casting

Directory of Open Access Journals (Sweden)

Ya-meng Wei

2018-01-01

Full Text Available Using silica sol as a binder for titanium investment casting is very attractive due to its good stability and reasonable cost as compared with yttrium sol and zirconium sol. However, the mechanism of interface reaction in the related system remains unclear. In this investigation, the interface reaction between Y2O3-SiO2 (Y-Si shell mold and titanium alloys was studied. A group of shell molds were prepared by using Y2O3 sand and silica sol with different contents of SiO2. Ti-6Al-4V alloy was cast under vacuum by gravity casting through cold crucible induction melting (CCIM method. Scanning electron microscopy (SEM and energy dispersive x-ray spectroscopy (EDS were employed to characterize the micromorphology and composition of the reaction area, respectively. X-ray photoelectron spectroscopy (XPS was used to confirm the valence state of relevant elements. White light interferometer (WLI was used to obtain the surface topography of Y-Si shells. The results show that the thickness of reaction layers is below 3 μm when the SiO2 content of silica sol is below 20wt.%. Whereas, when the SiO2 content increases to 25wt.%, the thickness of the reaction layer increases sharply to about 15 μm. There is a good balance between chemical inertness and mechanical performance when the SiO2 content is between 15 and 20wt.%. Moreover, it was found that the distribution of SiO2 and the roughness at the surface of the shell are the key factors that determine the level of reaction.

Abstracts of International Conference on Sol-Gel Materials' 04

International Nuclear Information System (INIS)

2004-01-01

International Conference on Sol-Gel Materials '04 was an important forum for discussion on problems related to sol-gel processes applied for preparation materials with special physical properties and assignment. The application of sol-gel materials as phosphors, surface coatings, sensors, waveguides, medical implants, joints etc. has been presented. Preparation conditions, methods of physical characterization as well as optimal chemical composition of such materials have been also discussed in detail

Highly stable and imperceptible electronics utilizing photoactivated heterogeneous sol-gel metal-oxide dielectrics and semiconductors.

Science.gov (United States)

Jo, Jeong-Wan; Kim, Jaekyun; Kim, Kyung-Tae; Kang, Jin-Gu; Kim, Myung-Gil; Kim, Kwang-Ho; Ko, Hyungduk; Kim, Jiwan; Kim, Yong-Hoon; Park, Sung Kyu

2015-02-18

Incorporation of Zr into an AlOx matrix generates an intrinsically activated ZAO surface enabling the formation of a stable semiconducting IGZO film and good interfacial properties. Photochemically annealed metal-oxide devices and circuits with the optimized sol-gel ZAO dielectric and IGZO semiconductor layers demonstrate the high performance and electrically/mechanically stable operation of flexible electronics fabricated via a low-temperature solution process. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Opportunity's Surroundings on Sol 1818

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

Propuesta de modificación al programa de Enfermería para incluir temas sobre la discapacidad infantil

Directory of Open Access Journals (Sweden)

María Cristina Pérez Guerrero

Full Text Available Con el objetivo de diseqar una propuesta de modificacisn al programa de la formacisn de enfermeros y sugerir la inclusisn de temas sobre la discapacidad infantil, que permitan instruir al personal en formacisn, se realizs un estudio descriptivo cualitativo, en dos etapas, en la primera, mediante entrevistas se recogis la opinisn del claustro de profesores de la Licenciatura en Enfermerma de la Universidad de Ciencias Midicas de Camag|ey, en una segunda etapa se aplics el mitodo de Panel de Expertos, en el que participaron diez expertos seleccionados de manera intencional a partir de su prestigio, experiencia y vinculacisn a la docencia, en lo referido al tema. Se analizaron los programas rectores de la carrera de formacisn en Enfermerma. El analisis de los mismos permitis apreciar aspectos tan importantes como el trabajo con la familia del discapacitado, o los procedimientos propios del manejo en el domicilio del discapacitado, los cuales no son objeto de estudio en la carrera. Se diseqs una estrategia curricular teniendo en cuenta los objetivos pedagsgicos a cumplimentar con las modificaciones propuestas. Se impone la necesidad de incluir en los programas de estudios aspectos relacionados con esta compleja tematica. Constituye un reto entonces para la universidad continuar desarrollando estrategias que permitan el desarrollo del proceso docente educativo y garanticen calidad en el egresado.

Sol-gel materials for optofluidics - process and applications

DEFF Research Database (Denmark)

Mikkelsen, Morten Bo Lindholm

2011-01-01

This Ph.D. thesis is concerned with the use of sol-gel materials in optofluidic applications and the physics of DNA molecules in nanoconfinement. The bottom-up formation of solid material, which is provided by the sol-gel process, enables control of the chemical composition and porosity...... of the material. At early stages of gelation, thin gel coatings can be structured by nanoimprint lithography, and purely inorganic silica materials can be obtained by subsequent thermal annealing. The sol-gel process thus constitutes a unique method for nanofabrication of silica materials of special properties....... In this work, sol-gel silica is introduced as a new material class for the fabrication of lab-on-a-chip devices for DNA analysis. An imprint process with a rigid, non-permeable stamp was developed, which enabled fabrication of micro- and nanofluidic silica channels in a single process step without use of any...

Del hermetismo en el discurso sobre el género : el transexualismo como síndrome cultural: del sexo generado al género transexuado

OpenAIRE

Aler Gay, María Isabel

1992-01-01

Esta tesis pretende un estudio semiológico de los discursos clínicos y del Derecho para llegar a plantear en el contexto situacional el fenómeno social de la transexualidad. La tesis central que mantiene la doctoranda es el hermetismo en el discurso sobre el género: el transexualismo como síndrome cultural del sexo generado al género transexuado

DIÁLOGOS E ENGAJAMENTO EM O CANTO DO SOL: REFLEXÕES SOBRE A LITERATURA DE OLNEY SÃO PAULO

Directory of Open Access Journals (Sweden)

Claudio Cledson Novaes

2010-12-01

Full Text Available Neste artigo, analisamos a produção literária do escritor e cineasta baiano Olney São Paulo, discutindo as relações entre a linguagem literária e cinematográfica em sua obra, privilegiando a discussão do engajamento cultural, através da leitura de sua narrativa de temática sertaneja, destacando do livro A Antevéspera e o Canto do Sol o conto “A Rebelião e o Vento”

Nickel-based xerogel catalysts: Synthesis via fast sol-gel method and application in catalytic hydrogenation of p-nitrophenol to p-aminophenol

Energy Technology Data Exchange (ETDEWEB)

Feng, Jin; Wang, Qiang; Fan, Dongliang; Ma, Lirong; Jiang, Deli; Xie, Jimin, E-mail: xiejm391@sohu.com; Zhu, Jianjun, E-mail: zhjj029@sina.com

2016-09-30

Graphical abstract: In order to investigate the roles of three-dimensional network structure and calcium on Ni catalysts, the Ni, Ni-Al{sub 2}O{sub 3}, Ni-Ca-Al{sub 2}O{sub 3} xerogel catalysts were successfully synthesized via the fast sol-gel process and chemical reduction method. - Highlights: • Epoxide-driven sol-gel and chemical reduction method subsequently were used to prepare Ni, Ni-Al{sub 2}O{sub 3} and Ni-Ca-Al{sub 2}O{sub 3} catalysts. • Three-dimensional network structure of the gel was employed to adjust the size and distribution of Ni nanoparticles. • Calcium was employed to shorten the gelation time, improve the nickel dispersion, decrease thenickel particle size and strengthen the Ni-Al{sub 2}O{sub 3} interaction. • The rate constants of Ni-Ca-Al2O3 catalysts (2.85 × 10{sup −3} s{sup −1}) is 2.8 times higher than the Ni catalysts (1.02 × 10{sup −3} s{sup −1}) and 2 times higher than the Ni-Al{sub 2}O{sub 3} catalysts(1.42 × 10{sup −3} s{sup −1}). • After 5 cycles, the conversion of PNP to PAP catalyzed by Ni, Ni-Al{sub 2}O{sub 3}, Ni-Ca-Al{sub 2}O{sub 3} remained 85%, 82%, 80%, respectively. - Abstract: In order to investigate the roles of three-dimensional network structure and calcium on Ni catalysts, the Ni, Ni-Al{sub 2}O{sub 3}, Ni-Ca-Al{sub 2}O{sub 3} xerogel catalysts were successfully synthesized via the fast sol-gel process and chemical reduction method. The crystal structure of three different catalysts was observed with X-ray powder diffraction (XRD). Transmission electron microscopy (TEM), scanning electron microscopy (SEM) and nitrogen adsorption-desorption were employed to investigate the role of network structure of xerogel catalysts and the size distribution of Ni nanoparticles. The catalyst composition was determined by inductively coupled plasma-optical emission spectrometry (ICP-OES) measurement and energy-dispersive X-ray spectroscopy (EDS). Temperature-programmed reduction (TPR) experiments were carried

Efectos sobre la salud en los trabajadores expuestos al dióxido de titanio

Directory of Open Access Journals (Sweden)

Angélica Faviola Gutiérrez Antezana

Full Text Available Objetivo principal: Revisar en la literatura científica si existen problemas en la salud y cuáles son, en los trabajadores expuestos al dióxido de titanio. Métodos: Revisión sistemática de la literatura científica recogida en las bases de datos MEDLINE (PubMed, Cochrane Library Plus, LILACS, OSH UPDATE, Biblioteca de la Organización internacional del Trabajo (OIT, Web of Science, IBECS. Los términos utilizados como descriptores y texto libre fueron: MeSH (thesaurus desarrollado por la U. S. National Library of Medicine, considerándose adecuados "Titanium", "Ocupational Exposure" y "Ocupational Diseases". Resultados: Se recuperaron 61 artículos. Tras aplicar los criterios de inclusión y exclusión obteniéndose 14 artículos (4 estudios de cohortes, 3 estudios de casos y controles, 1 estudio observacional descriptivo transversal, 4 estudios de casos clínicos y 2 estudios de serie de casos. En los cuales la población estudiada fue masculina en aproximadamente 90%. Entre los trabajadores expuestos se encuentran: Pintores, albañiles, mecánicos y empleados encargados de la fabricación de joyería artificial, pintura, papel, lacas, barnices y productores de TiO2. Las patologías encontradas con mayor frecuencia fueron las alteraciones respiratorias, seguidas de alteraciones cardiovasculares, alteraciones genéticas por exposición a nanopartículas de TiO2. No se encontró asociación entre exposición al TiO2 y cáncer pulmonar. Tampoco se encontró evidencia del incremento de la mortalidad por exposición. Discusión/Conclusión: Con los estudios seleccionados, no se puede establecer una asociación significativa entre exposición laboral al TIO2 y efectos sobre la salud, pese a que se encuentran descritas alteraciones respiratorias, cardiovasculares y sistémicas en trabajadores expuestos.

Sobre historia mundial hoy

Directory of Open Access Journals (Sweden)

Vera Weiler

2001-01-01

Full Text Available Los procesos de globalización son una realidad; su enorme impacto sobre la vida humana los ha convertido en un tema recurrente sobre el que se escribe y se comenta a diario también en Colombia. Los libros que de ellos tratan, ante todo los que 10 hacen en tono crítico, baten records en la industria editorial en todo el mundo. Las expectativas que acerca del futuro abrigan cientos de millones de personas se relacionan con 10 que ellas esperan, para bien o para mal, de la globalización. Las posturas que los gobernantes ocupan al respecto en el mundo son, cuando menos de aceptación, generalmente de activa participación en pos de la globalización. Por un lado, crece la preocupación y se multiplican las protestas; por el otro, dominan los razonamientos de los especialistas en materia de maximización de los rendimientos de los capitales que presentan la globalización, al estilo que se viene imponiendo, como el camino ineludible del gobierno universal de la eficiencia. ¿Tienen que decir algo los historiadores frente a todo esto?.

Combining Pre- and Post-Nucleation Trajectories for the Synthesis of High FAU-Content Faujasite Nanocrystals from Organic-Free Sols

Energy Technology Data Exchange (ETDEWEB)

Khaleel, Maryam; Xu, Wenqian; Lesch, David A.; Tsapatsis, Michael

2016-06-28

The effects of synthesis conditions on the FAU/EMT content and the size of nanocrystals, formed from inorganic aluminosilicate sols, were investigated. High resolution transmission electron microscopy imaging and comparison of experimental X-ray diffraction patterns with simulations demonstrated that all materials made starting from synthesis mixtures in the composition range (1.8-33) SiO2: 1 Al2O3: (2.7-33) Na2O: (41-1000) H2O contain FAU/EMT intergrowths. Compositions with low water content increase the FAU fraction up to 0.8 but the crystal size exceeds 100 nm. Extension of the higher FAU purity to nanocrystals was achieved only by first mixing the sol at high water content compositions that favor nanocrystal formation and then - after a certain time - lowering by freeze-drying the water to levels favoring the formation of FAU. Cryogenic transmission electron microscopy and small angle X-ray scattering from representative optically clear and colloidally stable precursor sols (aged and crystallized at ambient temperature) reveal the formation of amorphous aggregates before the detection of crystals, in agreement with earlier findings and an existing model for the aggregative growth of the zeolite MFI. The presence of these amorphous aggregates coincides with the aforementioned state of sol that preserves the original trajectory towards nano-crystals after the pronounced reduction of water content by freeze-drying. If water reduction by freeze-drying is applied earlier (before the detection of amorphous aggregates), the sol follows the low water content trajectory towards larger crystals. Despite this memory effect, the sol at this stage is still agnostic towards FAU or EMT formation, the relative content of which is dominantly determined by the final water content. These findings demonstrate that it is possible to combine the effects of pre-and post-nucleation sol composition to steer crystal size and crystal structure, respectively. They confirm precursor

Structural Evolution and Stability of Sol-Gel Biocatalysts

International Nuclear Information System (INIS)

Rodgers, L.E.; Foster, L.J.R.; Holden, P.J.; Knott, R.B.; Bartlett, J.B.

2005-01-01

Full text: Immobilisation strategies for catalytic enzymes are important as they allow reuse of the biocatalysts. Sol-gel materials have been used to immobilise Candida antarctica lipase B (CALB), a commonly used industrial enzyme with a known crystal structure. The sol-gel bioencapsulate is produced through the condensation of suitable metal alkoxides in the presence of CALB, yielding materials with controlled pore sizes, volume and surface chemistry. Sol-gel matrices have been shown to prolong the catalytic life and enhance the activity of CALB, although the molecular basis for this effect has yet to be elucidated due to the limitations of analysis techniques applied to date. Small angle neutron scattering (SANS) allows such multicomponent systems to be characterised through contrast matching. In the sol-gel bioencapsulate system, at the contrast match point for silica, residual scattering intensity is due to the CALB and density fluctuations in the matrix. A SANS contrast variation series found the match point for the silica matrix, both with and without enzyme present, to be around 35 percent. The model presented here proposes a mechanism for the interaction between CALB and the surrounding sol-gel matrix, and the observed improvement in enzyme activity and matrix strength. The SANS protocol developed here may be applied more generally to bioencapsulates. (authors)

Análisis competitivo mediante grupos estratégicos y su influencia sobre el desempeño: aplicación al sector hotelero español

OpenAIRE

Pereira-Moliner, Jorge

2005-01-01

Este documento de trabajo pretende reflejar, de forma resumida, los resultados obtenidos en la tesis titulada “Análisis competitivo mediante grupos estratégicos y su influencia sobre el desempeño: aplicación al sector hotelero español” que fue presentada en el Departamento de Organización de Empresas de la Universidad de Alicante en 2005.

Conversaciones sobre el litoral cordillerano

OpenAIRE

Browne,Enrique; Browne,Tomás

2009-01-01

Dos arquitectos dialogan sobre los Andes desde su propia vivencia. El territorio de Chile se entiende como límite natural entre mar y cordillera, donde suceden apretadamente una serie de eventos particulares: fallas geológicas, cerros que penetran en las ciudades y torrentes que bajan al mar caracterizan y diferencian sus paisajes.

Efecto del dopado con Si sobre la estructura de defectos en sistemas heteroepitaxiales GaN/AlN/Si(111

Directory of Open Access Journals (Sweden)

Sánchez, A. M.

2000-08-01

Full Text Available The Si doping effect on the defect structure in GaN epilayers grown by molecular beam epitaxy on Si(111 substrates using AlN buffer layers has been studied. Transmission electron microscopy and related techniques have been used to carry out the structural characterization. The Si doping affects both the subgrain size and misorientation in GaN epilayer mosaic structure. The Si doping also leads to an increase of the planar defect density, as well as a decrease of the threading dislocation density. The enlargement of the subgrain tilt and the planar defect density explain the reduction of the dislocation density reaching the GaN free surface.

En el presente artículo se lleva a cabo el análisis del efecto que el dopado con Si tiene sobre la estructura de defectos en epicapas de GaN crecidas por epitaxia de haces moleculares sobre sustratos de Si (111 utilizando capas amortiguadoras de AlN. La caracterización estructural se llevó a cabo mediante microscopía electrónica de transmisión convencional y de alta resolución. El dopado con Si afecta a la desorientación y tamaño de los subgranos que constituyen la estructura mosaico de la epicapa de GaN. El dopado con Si provoca un aumento en la densidad de defectos planares, así como una disminución en la densidad de dislocaciones de propagación. El incremento en el grado de desorientación de inclinación, así como en la densidad de defectos planares que se produce conforme aumenta el dopado con Si explican la disminución en la densidad de dislocaciones que alcanzan la superficie libre de GaN.

Avance de investigación. La "no sujeción" de las fundaciones al impuesto sobre la renta en Colombia. Visión desde el derecho español

Directory of Open Access Journals (Sweden)

Juan Carlos Gallego García

2006-01-01

Full Text Available Este avance de investigación presenta los argumentos sostenidos por parte de la doctrina española que se inclina por la total sujeción de las fundaciones al impuesto sobre sociedades (impuesto sobre la renta en Colombia. Las razones se podrían resumir en cuatro ideas: el quebranto del principio de igualdad por el hecho de ser persona jurídica, para evitar ventajas que distorsionen el mercado, para evitar fraudes y, por último, porque poseen capacidad contributiva. Cada una de estas ideas se analiza, contrastándola con la realidad colombiana.

Synthesis by sol-gel and characterization of catalysts Ag/Al2O3- CeO2 for the elimination of nitric oxide

International Nuclear Information System (INIS)

Zayas R, M.L.

2005-01-01

The environmental pollution is one from the big problems to solve at the present time, because the quality of the alive beings life is affected. For such reason, more clean and economic technologies are required, that it conduces to develop new catalytic alternatives to diminish the nitrogen oxides that due to its chemical processes in the environment contribute considerably in the air pollution. The main objective of the present work, is the preparation and characterization of catalytic materials with base of silver supported in simple and mixed aluminium oxides (Al 2 O 3 ) and Cerium oxide (CeO 2 ), and its catalytic evaluation that through of the reduction of nitric oxide (NO) using hydrogen (H 2 ) as reducer agent. It was synthesized alumina (Al 2 O 3 ) and Cerium oxide (CeO 2 ) and mixed oxides (Al 2 O 3 - CeO 2 ), by the sol-gel method and the cerium oxide (CeO 2 ) by precipitation of the cerium nitrate (III) hexa hydrated. The oxides were stabilized thermally at 900 C by 5 hr. The catalysts were prepared by impregnation using silver nitrate (AgNO 3 ), the nominal concentration of Ag was of 5% in weight. The catalysts were reduced at 400 C by 2 hr, in hydrogen flow of 60 cc/min. The characterization of the catalytic materials was carried out through different techniques as: nitrogen adsorption to determine the surface area BET, scanning electron microscopy (SEM) to observe the final morphology of the catalysts, X-ray diffraction (XRD) to identify the crystalline phases of the catalytic materials, Infrared spectroscopy (DRIFT) to know the structural characterization of the catalysts, reduction to programmed temperature (TPR) to evidence the interaction metal-support. The catalytic properties of the catalysts were evaluated in the model reaction NO + H 2 , to determine the activity and selectivity. The results indicate that the preparation technique, the precursors and the thermal treatments that underwent these materials influence in the catalyst and by

Evaluation of sol-gel derived Eu{sup 2+} activated SrMgAl{sub 2}SiO{sub 7} as a novel nanostructure luminescent pigment

Energy Technology Data Exchange (ETDEWEB)

Sameie, H.; Salimi, R. [Faculty of Polymer and Color Engineering, Amirkabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Sabbagh Alvani, A.A., E-mail: sabbagh_alvani@aut.ac.i [Color and Polymer Research Center (CPRC), Amirkabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Sarabi, A.A. [Faculty of Polymer and Color Engineering, Amirkabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Moztarzadeh, F.; Tahriri, M. [Biomaterials Group, Faculty of Biomedical Engineering, Amirkabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of)

2010-12-01

A novel nanostructure pigment of Eu{sup 2+} doped SrMgAl{sub 2}SiO{sub 7} was prepared via the sol-gel route. The phase composition and condition of crystallites during heating were characterized by X-ray diffraction (XRD) analysis. Investigation of optical properties by spectrophotometer illustrated that under short ultraviolet excitation wavelength, the main emission peak occurred at about 415-420 nm. Also, relatively pure purplish blue color was observed that can be ascribed to the 4f{sup 6}5d{sup 1}({sup 2}D){yields}4f{sup 7}({sup 8}S{sub 7/2}) transition of Eu{sup 2+}. The effect of calcination temperature on the luminescence properties of the phosphors was evaluated and, also in this case, scanning electron microscope (SEM) was employed. From colorimetry results, color coordinations of phosphor shift towards the deep blue region as calcination temperature increases. Finally, grain size of products at optimum calcination temperature was estimated to be about 20-30 nm using Scherrer's equation, which was consistent with transmission electron microscopy (TEM) observations.

A longitudinal study of the residents' perceptions of tourism impacts using data from the sunshine coast Australia

Directory of Open Access Journals (Sweden)

Bishnu Sharma

2012-01-01

Full Text Available Este estudio investiga si ha habido un cambio de percepciones de los residentes de la Costa del Sol australiana sobre los impactos del turismo en el año 2009, comparándolo con el 2008. En el 2009 un mayor número de enuestados opinaron que el estilo y ritmo de vida son los principales atractivos del al Costa del Sol. Los resultados también demuestran un aumento signifi cativo en las perepcionesde los residentes sobre el impacto positivo del turismo en la identidad cultural de la comunidad. El estudio también encontró que entre el 2008 y el 2009 hubo una disminución signifi cativa de las preocupaciones de los residentes con respecto al tráfi co, el ruido y la contaminación, los índices de criminalidad, la des-trucción del medio ambiente, playas, rutas de senderimso, parques e instalaciones al aire libre. La inves-tigación, sin embargo, no revela diferencias signifi cativas en las percepcionesde los residentes sobre la conservación de los recursos naturales, la creación de empleo y la posibilidad de tener un intercambio más cultural entre turistas y residentes. En general estos resultados son favorables para las partes intere-sadas en el desarrollo de planes de futuro para turismo en la región, ya que los residentes parecen dis-puestos a apoyar el desarrollo turístico.

Estudio sobre Logística urbana en el casco antiguo de Cartagena

OpenAIRE

Muñoz Heredia, Jorge

2014-01-01

El objetivo principal del proyecto es el análisis de la logística urbana y posibles problemas existentes respecto al transporte del Casco Antiguo de Cartagena. La metodología a emplear será parecida a la propuesta Taniguchi 1999, cuyos pasos a seguir son: La descripción de los problemas existentes en la ciudad respecto al transporte de mercancías, en éste caso se ha cogido como referencia, el centro histórico de Cartagena, que hemos delimitados tres puntos claves: 1) Bar Sol, intersección ...

Periodismo gráfico entre democracia y dictadura. El Sol de Quilmes a través de sus editoriales

OpenAIRE

Alberico, Anahí; Bernat, María Sofía; Castiglione, María Belén; Taboada, Mirta

2015-01-01

El presente artículo, enmarcado en el proyecto de extensión de la Universidad Nacional de Quilmes, “Universidad por la Identidad”, realiza un primer acercamiento analítico a las editoriales del diario El Sol de la localidad mencionada. El corpus de análisis se limita a los textos correspondientes al primer semestre de 1976, es decir que abarca tanto al gobierno de María Estela Martínez de Perón como los primeros meses de la última dictadura cívico-militar. Se trabaja desde la perspe...

Turismo en la Costa del Sol. Un patrimonio en revisión

Directory of Open Access Journals (Sweden)

Lourdes Royo Naranjo

2014-01-01

Full Text Available La trigésimo cuarta edición de la Feria Internacional de Turismo, FITUR (2014, ha sido considerada por muchos inversores, como el mejor reflejo de la recuperación que está experimentando el sector turístico a escala internacional. Tal es el caso de la Costa del Sol, un destino maduro de una enorme riqueza, para el que creemos necesaria, sin embargo, una reconsideración de su modelo turístico, que ponga el foco no tanto en los aspectos mercantilistas como en la puesta en valor de una producción cultural moderna ligada al ocio de masas. Producción que ha construido una realidad identitaria alternativa, aún poco explorada, y que pretendemos atender para una valoración patrimonial contemporánea. Arquitectura, cine o literatura del turismo en la Costa del Sol se convertirían en nuevos ítems para una visión más amplia, integradora y productiva, con la que acometer nuevos desafíos en el planeamiento y la promoción turística de este destino.

Recubrimiento de cobre sobre Al₂O₃ mediante reducción autocatalítica

Directory of Open Access Journals (Sweden)

Gómez de Salazar, J. M.

1998-05-01

Full Text Available A method for obtaining copper coatings on ceramic tenacious substrates as the alumina is described. Its principal applications are found in the electronic industry; they can also be employed as interlayer on metal-ceramic disimilar bondings produced by solid state welding or brazing. Optimal activation conditions were determined as well as the influence of the substrate surface preparation and the deposition rate on the adhesion. The kinetics study of the process was carried out by gravimetric and electrochemical methods.

Se describe un método para la obtención de recubrimientos de cobre sobre un cerámico tenaz, como es la alúmina. Entre sus principales aplicaciones se encuentra la industria electrónica, aunque también pueden emplearse como intermediarios en las uniones disimilares metal-cerámico realizadas mediante soldadura en estado sólido o soldadura fuerte. Se determinan las condiciones óptimas de activación y la influencia de la preparación superficial del substrato, así como de la velocidad de deposición sobre la adherencia de la capa de cobre. El estudio cinético del proceso se realizó mediante ensayos electroquímicos.

Opportunity's View After Long Drive on Sol 1770

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 104 meters (341 feet) on the 1,770th Martian day, or sol, of Opportunity's surface mission (January 15, 2009). Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Prior to the Sol 1770 drive, Opportunity had driven less than a meter since Sol 1713 (November 17, 2008), while it used the tools on its robotic arm first to examine a meteorite called 'Santorini' during weeks of restricted communication while the sun was nearly in line between Mars and Earth, then to examine bedrock and soil targets near Santorini. The rover's position after the Sol 1770 drive was about 1.1 kilometer (two-thirds of a mile) south southwest of Victoria Crater. Cumulative odometry was 13.72 kilometers (8.53 miles) since landing in January 2004, including 1.94 kilometers (1.21 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a cylindrical projection with geometric seam correction.

Reflexions sociològiques figuratives i de procés sobre l’esport i la globalització: algunes observacions conceptuals i teòriques, amb especial referència al futbol

OpenAIRE

Dunning, Eric

2009-01-01

Aquest article es divideix en tres parts. La primera consisteix en un comentari conceptual teòric sobre la globalització i en diversos exemples del món globalitzat de l’esport; la segona és un comentari sobre el desenvolupament i l’extensió global del futbol; i la tercera exposa el comentari d’algunes patologies relacionades amb l’esport. Tot al llarg de l’article s’aplica l’enfocament sociològic figuratiu i de procés desenvolupat per Norbert Elias. En resum, aquest treball és fonamentalment ...

Strength of interactions between immobilized dye molecules and sol-gel matrices.

Science.gov (United States)

Ismail, Fanya; Schoenleber, Monika; Mansour, Rolan; Bastani, Behnam; Fielden, Peter; Goddard, Nicholas J

2011-02-21

In this paper we present a new theory to re-examine the immobilization technique of dye doped sol-gel films, define the strength and types of possible bonds between the immobilized molecule and sol-gel glass, and show that the immobilized molecule is not free inside the pores as was previously thought. Immobilizing three different pH sensitive dyes with different size and functional groups inside the same sol-gel films revealed important information about the nature of the interaction between the doped molecule and the sol-gel matrix. The samples were characterized by means of ultraviolet-visible spectrophotometer (UV-VIS), thermal gravimetric analysis (TGA), mercury porosimetry (MP), nuclear magnetic resonance spectroscopy ((29)Si NMR) and field-emission environmental scanning electron microscopy (ESEM-FEG). It was found that the doped molecule itself has a great effect on the strength and types of the bonds. A number of factors were identified, such as number and types of the functional groups, overall charge, size, pK(a) and number of the silanol groups which surround the immobilized molecule. These results were confirmed by the successful immobilization of bromocresol green (BCG) after a completely polymerized sol-gel was made. The sol-gel consisted of 50% tetraethoxysilane (TEOS) and 50% methyltriethoxysilane (MTEOS) (w/w). Moreover, the effect of the immobilized molecule on the structure of the sol-gel was studied by means of a leaky waveguide (LW) mode for doped films made before and after polymerization of the sol-gel.

Sol-gel encapsulation for controlled drug release and biosensing

Science.gov (United States)

Fang, Jonathan

The main focus of this dissertation is to investigate the use of sol-gel encapsulation of biomolecules for controlled drug release and biosensing. Controlled drug release has advantages over conventional therapies in that it maintains a constant, therapeutic drug level in the body for prolonged periods of time. The anti-hypertensive drug Captopril was encapsulated in sol-gel materials of various forms, such as silica xerogels and nanoparticles. The primary objective was to show that sol-gel silica materials are promising drug carriers for controlled release by releasing Captopril at a release rate that is within a therapeutic range. We were able to demonstrate desired release for over a week from Captopril-doped silica xerogels and overall release from Captopril-doped silica nanoparticles. As an aside, the antibiotic Vancomycin was also encapsulated in these porous silica nanoparticles and desired release was obtained for several days in-vitro. The second part of the dissertation focuses on immobilizing antibodies and proteins in sol-gel to detect various analytes, such as hormones and amino acids. Sol-gel competitive immunoassays on antibody-doped silica xerogels were used for hormone detection. Calibration for insulin and C-peptide in standard solutions was obtained in the nM range. In addition, NASA-Ames is also interested in developing a reagentless biosensor using bacterial periplasmic binding proteins (bPBPs) to detect specific biomarkers, such as amino acids and phosphate. These bPBPs were doubly labeled with two different fluorophores and encapsulated in silica xerogels. Ligand-binding experiments were performed on the bPBPs in solution and in sol-gel. Ligand-binding was monitored by fluorescence resonance energy transfer (FRET) between the two fluorophores on the bPBP. Titration data show that one bPBP has retained its ligand-binding properties in sol-gel.

Pemodelan Desain Sol Sepatu dengan Inovasi Penambahan Wave Spring

Directory of Open Access Journals (Sweden)

Redyarsa Dharma Bintara

2015-07-01

Full Text Available Desain sepatu sport berkembang pesat dengan tujuan mengurangi cedera dan meningkatkankenyamanan pengguna. Pengurangan cedera dilakukan dengan cara memperbesar energi yangdiserap dari beban akibat pengguna berlari atau melompat. Pada penelitian ini dilakukanpenambahan wave spring yang digunakan sebagai mekanisme penyerap beban.Pemodelandilakukan pada sol sepatu dengan menggunakan bantuan software finite element method (FEMAnsys 14.5 Academic. Model awal dilakukan untuk mengetahui batas deformasi sol sepatu yangakan dimanfaatkan sebagai input model berikutnya yaitu model dengan diberikan inovasipenambahan wave spring. Analisa difokuskan pada sol sepatu bagian belakang (tumit kaki.Darihasil simulasi, didapatkan bahwa penyerapan energi sol sepatu dengan penambahan wave springlebih besar daripada penyerapan energi sol sepatu tanpa penambahan wave spring, sehinggapenambahan wave spring memungkinkan untuk diaplikasikan pada sol sepatu sport.Kata kunci: Penyerapan energi, wave spring, sol sepatu. Sport shoe design had been developed rapidly with the purpose to reduce injuries and increaseuser comfort. Reduction of injury is done by enlarging the energy absorbed from the user running orjumping load. In this study, the addition of the wave spring is used as the load absorbingmechanism. The shoes sole is modeled by using finite element method (FEM software Ansys 14.5Academic. Initial model was conducted to determine the deformation boundary in soles which willbe used as input to the next model for the wave spring addition innovation. Analysis focused onshoe sole on heel foot. From the simulation results, it was found that the energy absorption shoessoles with the addition of the wave spring is greater than the energy absorption soles without theaddition of wave spring. It can be concluded that the addition of a spring wave can be applied to thesoles of sports shoes.Keywords: Energy absorb, wave spring, shoe sole, deformation boundary

Time for a Change; Spirit's View on Sol 1843 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this full-circle view of the rover's surroundings during the 1,843rd Martian day, or sol, of Spirit's surface mission (March 10, 2009). South is in the middle. North is at both ends. This view is presented as a polar projection with geometric seam correction. North is at the top. The rover had driven 36 centimeters downhill earlier on Sol 1854, but had not been able to get free of ruts in soft material that had become an obstacle to getting around the northeastern corner of the low plateau called 'Home Plate.' The Sol 1854 drive, following two others in the preceding four sols that also achieved little progress in the soft ground, prompted the rover team to switch to a plan of getting around Home Plate counterclockwise, instead of clockwise. The drive direction in subsequent sols was westward past the northern edge of Home Plate.

Time for a Change; Spirit's View on Sol 1843 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this full-circle view of the rover's surroundings during the 1,843rd Martian day, or sol, of Spirit's surface mission (March 10, 2009). South is in the middle. North is at both ends. This view is presented as a vertical projection with geometric seam correction. North is at the top. The rover had driven 36 centimeters downhill earlier on Sol 1854, but had not been able to get free of ruts in soft material that had become an obstacle to getting around the northeastern corner of the low plateau called 'Home Plate.' The Sol 1854 drive, following two others in the preceding four sols that also achieved little progress in the soft ground, prompted the rover team to switch to a plan of getting around Home Plate counterclockwise, instead of clockwise. The drive direction in subsequent sols was westward past the northern edge of Home Plate.

Water-based sol-gel synthesis of hydroxyapatite: process development.

Science.gov (United States)

Liu, D M; Troczynski, T; Tseng, W J

2001-07-01

Hydroxyapatite (HA) ceramics were synthesized using a sol-gel route with triethyl phosphite and calcium nitrate as phosphorus and calcium precursors, respectively. Two solvents, water and anhydrous ethanol, were used as diluting media for HA sol preparation. The sols were stable and no gelling occurred in ambient environment for over 5 days. The sols became a white gel only after removal of the solvents at 60 degrees C. X-ray diffraction showed that apatitic structure first appeared at a temperature as low as 350 degrees C. The crystal size and the HA content in both gels increase with increasing calcination temperature. The type of initial diluting media (i.e., water vs. anhydrous ethanol) did not affect the microstructural evolution and crystallinity of the resulting HA ceramic. The ethanol-based sol dip-coated onto a Ti substrate, followed by calcination at 450 degrees C, was found to be porous with pore size ranging from 0.3 to 1 microm. This morphology is beneficial to the circulation of physiological fluid when the coating is used for biomedical applications. The satisfactory adhesion between the coating and substrate suggests its suitability for load-bearing uses.

Production of continuous mullite fiber via sol-gel processing

Science.gov (United States)

Tucker, Dennis S.; Sparks, J. Scott; Esker, David C.

1990-01-01

The development of a continuous ceramic fiber which could be used in rocket engine and rocket boosters applications was investigated at the Marshall Space Flight Center. Methods of ceramic fiber production such as melt spinning, chemical vapor deposition, and precursor polymeric fiber decomposition are discussed and compared with sol-gel processing. The production of ceramics via the sol-gel method consists of two steps, hydrolysis and polycondensation, to form the preceramic, followed by consolidation into the glass or ceramic structure. The advantages of the sol-gel method include better homogeneity and purity, lower preparation temperature, and the ability to form unique compositions. The disadvantages are the high cost of raw materials, large shrinkage during drying and firing which can lead to cracks, and long processing times. Preparation procedures for aluminosilicate sol-gel and for continuous mullite fibers are described.

Ultrasound-assisted sol-gel synthesis of ZrO2.

Science.gov (United States)

Guel, Marlene Lariza Andrade; Jiménez, Lourdes Díaz; Hernández, Dora Alicia Cortés

2017-03-01

Synthesis of tetragonal ZrO 2 by both conventional sol-gel and ultrasound-assisted sol-gel methods and using a non-ionic surfactant Tween-20, was performed. A porous microstructure composed of nanometric particles was observed. Tetragonal ZrO 2 was obtained using a low heat treatment temperature of powders, 500°C by both methods. A higher crystallinity and a shorter reaction time were observed when ultrasound was used in the sol-gel method due to the cavitation phenomenon. Copyright © 2016 Elsevier B.V. All rights reserved.

Ceramic protective coatings applied by sol-gel or electrophoresis

International Nuclear Information System (INIS)

Stoch, A.

1993-01-01

Sol-gel and electrophoresis are the complementary techniques which may be used for obtaining the ceramic coatings. The composition of such a coatings depends on the composition of electrophoresis bath or sol solution. Thermal treatment is used for densifying the coating and promoting the adherence of coating to the substrate. In presented work silica, silica-alumina or alumina coatings are applied by sol-gel dip coating procedure on steel, aluminium or ceramic substrates. Electrophoresis is employed for obtaining zirconia, alumina or hydroxyapatite coatings on stainless steel. (author). 7 refs

Radiación ultravioleta

OpenAIRE

Bohórquez-Ballén, Jaime; Pérez Mogollón, José Fernando

2007-01-01

La energía proveniente del sol que incide sobre la superficie de la tierra consta principalmente de radiación infrarroja, visible y ultravioleta (UV). La porción del espectro solar correspondiente al UV (cerca del 7%) afecta en gran manera la vida sobre la tierra. Pequeñas cantidades de UV son necesarias en los seres humanos para asimilar la vitamina D; en las plantas bajo condiciones normales ayudas en el proceso de foto-síntesis pero cuando la exposición a este tipo de radiación es exagerad...

Opportunity's View After Drive on Sol 1806

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 60.86 meters (200 feet) on the 1,806th Martian day, or sol, of Opportunity's surface mission (Feb. 21, 2009). North is at the center; south at both ends. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Engineers designed the Sol 1806 drive to be driven backwards as a strategy to redistribute lubricant in the rovers wheels. The right-front wheel had been showing signs of increased friction. The rover's position after the Sol 1806 drive was about 2 kilometer (1.2 miles) south southwest of Victoria Crater. Cumulative odometry was 14.74 kilometers (9.16 miles) since landing in January 2004, including 2.96 kilometers (1.84 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a cylindrical projection with geometric seam correction.

Opportunity's Surroundings on Sol 1798

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

Neutron detector based on lithiated sol-gel glass

CERN Document Server

Wallace, S; Miller, L F; Dai, S

2002-01-01

A neutron detector technology is demonstrated based on sup 6 Li/ sup 1 sup 0 B doped sol-gel glass. The detector is a sol-gel glass film coated silicon surface barrier detector (SBD). The ionized charged particles from (n, alpha) reactions in the sol-gel film enter the SBD and are counted. Data showing that gamma-ray pulse amplitudes interfere with identifying charged particles that exit the film layer with energies below the gamma-ray energy is presented. Experiments were performed showing the effect of sup 1 sup 3 sup 7 Cs and sup 6 sup 0 Co gamma rays on the SBD detector. The reaction product energies of the triton and alpha particles from sup 6 Li are significantly greater than the energies of the Compton electrons from high-energy gamma rays, allowing the measurement of neutrons in a high gamma background. The sol-gel radiation detection technology may be applicable to the characterization of transuranic waste, spent nuclear fuel and to the monitoring of stored plutonium.

Sol-Gel Chemistry for Carbon Dots.

Science.gov (United States)

Malfatti, Luca; Innocenzi, Plinio

2018-03-14

Carbon dots are an emerging class of carbon-based nanostructures produced by low-cost raw materials which exhibit a widely-tunable photoluminescence and a high quantum yield. The potential of these nanomaterials as a substitute of semiconductor quantum dots in optoelectronics and biomedicine is very high, however they need a customized chemistry to be integrated in host-guest systems or functionalized in core-shell structures. This review is focused on recent advances of the sol-gel chemistry applied to the C-dots technology. The surface modification, the fine tailoring of the chemical composition and the embedding into a complex nanostructured material are the main targets of combining sol-gel processing with C-dots chemistry. In addition, the synergistic effect of the sol-gel precursor combined with the C-dots contribute to modify the intrinsic chemo-physical properties of the dots, empowering the emission efficiency or enabling the tuning of the photoluminescence over a wide range of the visible spectrum. © 2018 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Opportunity's Surroundings on Sol 1687 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11739 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11739 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this stereo, 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). The view appears three-dimensional when viewed through red-blue glasses. Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This panorama combines right-eye and left-eye views presented as cylindrical-perspective projections with geometric seam correction.

Sol-gel growth of vanadium dioxide

International Nuclear Information System (INIS)

Speck, K.R.

1990-01-01

This thesis examines the chemical reactivity of vanadium (IV) tetrakis(t-butoxide) as a precursor for the sol-gel synthesis of vanadium dioxide. Hydrolysis and condensation of the alkoxide was studied by FTIR spectroscopy. Chemical modification of the vanadium tetraalkoxide by alcohol interchange was studied using 51 V NMR and FTIR. Vanadium dioxide thin films and powders were made from vanadium tetrakis(t-butoxide) by standard sol-gel techniques. Post-deposition heating under nitrogen was necessary to transform amorphous gels into vanadium dioxide. Crystallization of films and powders was studied by FTIR, DSC, TGA, and XRD. Gel-derived vanadium dioxide films undergo a reversible semiconductor-to-metal phase transition near 68C, exhibiting characteristic resistive and spectral changes. The electrical resistance decreased by two to three orders of magnitude and the infrared transmission sharply dropped as the material was cycled through this thermally induced phase transition. The sol-gel method was also used to make doped vanadium dioxide films. Films were doped with tungsten and molybdenum ions to effectively lower the temperature at which the transition occurs

Derecho humano al agua y al saneamiento: derechos estrechamente vinculados al derecho a la vida

OpenAIRE

Fernández Aller, Maria Celia; Luis Romero, Elena de; Guzmán Acha, Cristina

2013-01-01

Los derechos humanos al agua y al saneamiento están íntimamente relacionados con otros derechos esenciales para la vida, como la alimentación o la salud. Su reconocimiento como derechos humanos en 2010 marca un hito importante en el respeto, protección y realización de estos derechos, que se encuentran seriamente vulnerados para una mayoría de población más vulnerable y empobrecida, sobre todo en el ámbito rural. Mucho camino queda aún para conseguir no sólo la disponibilidad de agua y saneam...

New Record Five-Wheel Drive, Spirit's Sol 1856 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11962 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11962 NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this stereo, 180-degree view of the rover's surroundings during the 1,856th Martian day, or sol, of Spirit's surface mission (March 23, 2009). The center of the view is toward the west-southwest. This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The rover had driven 25.82 meters (84.7 feet) west-northwestward earlier on Sol 1856. This is the longest drive on Mars so far by a rover using only five wheels. Spirit lost the use of its right-front wheel in March 2006. Before Sol 1856, the farthest Spirit had covered in a single sol's five-wheel drive was 24.83 meters (81.5 feet), on Sol 1363 (Nov. 3, 2007). The Sol 1856 drive made progress on a route planned for taking Spirit around the western side of the low plateau called 'Home Plate.' A portion of the northwestern edge of Home Plate is prominent in the left quarter of this image, toward the south. This view is presented as a cylindrical-perspective projection with geometric seam correction.

Optical Sensors for Biomolecules Using Nanoporous Sol-Gel Materials

Science.gov (United States)

Fang, Jonathan; Zhou, Jing C.; Lan, Esther H.; Dunn, Bruce; Gillman, Patricia L.; Smith, Scott M.

2004-01-01

An important consideration for space missions to Mars is the ability to detect biosignatures. Solid-state sensing elements for optical detection of biological entities are possible using sol-gel based biologically active materials. We have used these materials as optical sensing elements in a variety of bioassays, including immunoassays and enzyme assays. By immobilizing an appropriate biomolecule in the sol-gel sensing element, we have successfully detected analytes such as amino acids and hormones. In the case of the amino acid glutamate, the enzyme glutamate dehydrogenase was the immobilized molecule, whereas in the case of the hormone cortisol, an anti-cortisol antibody was immobilized in the sensing element. In this previous work with immobilized enzymes and antibodies, excellent sensitivity and specificity were demonstrated in a variety of formats including bulk materials, thin films and fibers. We believe that the sol-gel approach is an attractive platform for bioastronautics sensing applications because of the ability to detect a wide range of entities such as amino acids, fatty acids, hopanes, porphyrins, etc. The sol-gel approach produces an optically transparent 3D silica matrix that forms around the biomolecule of interest, thus stabilizing its structure and functionality while allowing for optical detection. This encapsulation process protects the biomolecule and leads to a more "rugged" sensor. The nanoporous structure of the sol-gel matrix allows diffusion of small target molecules but keeps larger, biomolecules immobilized in the pores. We are currently developing these biologically active sol-gel materials into small portable devices for on-orbit cortisol detection

Environmentally benign sol-gel antifouling and foul-releasing coatings.

Science.gov (United States)

Detty, Michael R; Ciriminna, Rosaria; Bright, Frank V; Pagliaro, Mario

2014-02-18

Biofouling on ships and boats, characterized by aquatic bacteria and small organisms attaching to the hull, is an important global issue, since over 80000 tons of antifouling paint is used annually. This biofilm, which can form in as little as 48 hours depending on water temperature, increases drag on watercraft, which greatly reduces their fuel efficiency. In addition, biofouling can lead to microbially induced corrosion (MIC) due to H2S formed by the bacteria, especially sulfate-reducing bacteria. When the International Maritime Organization (IMO) international convention banned the use of effective but environmentally damaging coatings containing tributyl tin in 2008, the development of clean and effective antifouling systems became more important than ever. New nonbiocidal coatings are now in high demand. Scientists have developed new polymers, materials, and biocides, including new elastomeric coatings that they have obtained by improving the original silicone (polydimethylsiloxane) formulation patented in 1975. However, the high cost of silicones, especially of fluoropolymer-modified silicones, has generally prevented their large-scale diffusion. In 2009, traditional antifouling coatings using cuprous oxide formulated in copolymer paints still represented 95% of the global market volume of anti-fouling paints. The sol-gel nanochemistry approach to functional materials has emerged as an attractive candidate for creating low fouling surfaces due to the unique structure and properties of silica-based coatings and of hybrid inorganic-organic silicas in particular. Sol-gel formulations easily bind to all types of surfaces, such as steel, fiberglass, aluminum, and wood. In addition, they can cure at room temperature and form thin glassy coatings that are markedly different from thick silicone elastomeric foul-releasing coatings. Good to excellent performance against biofouling, low cure temperatures, enhanced and prolonged chemical and physical stability, ease of

Durable flame retardant finish for silk fabric using boron hybrid silica sol

Energy Technology Data Exchange (ETDEWEB)

Zhang, Qiang-hua; Gu, Jiali; Chen, Guo-qiang [National Engineering Laboratory for Modern Silk, Soochow University (China); Xing, Tie-ling, E-mail: xingtieling@suda.edu.cn [National Engineering Laboratory for Modern Silk, Soochow University (China); Jiangsu HuaJia Group (China)

2016-11-30

Highlights: • Highly homogeneous boron hybrid silica sol flame retardant system was prepared through sol-gel method. • The silk samples treated and cross-linked by this hybrid sol and BTCA solution showed a higher limiting oxygen index (LOI) more than 31.0% and a better washing durability for more than 30 times washing. • The smoke suppression, combustion performance and thermal stability properties of the treated samples have a significant improvement. - Abstract: A hybrid silica sol was prepared via sol gel method using tetraethoxysilane (TEOS) as a precursor and boric acid (H{sub 3}BO{sub 3}) as flame retardant additive and then applied to silk fabric. In order to endow silk fabric with durable flame retardancy, 1,2,3,4-butanetetracarboxylic acid (BTCA) was used as cross-linking agent for the sake of strong linkage formation between the hybrid silica sol and silk fabric. The FT-IR and XPS analysis demonstrated the Si-O-B formation in the sol system, as well as the linkage between the sol and silk after the treatment. The limiting oxygen index (LOI) and smoke density test indicated good flame retardancy and smoke suppression of the treated silk fabrics. The micro calorimeter combustion (MCC) test and thermo gravimetric (TG) analysis showed that the treated samples had less weight loss in the high temperature and lower heat release rate when burning. The washing durability evaluation results indicated that there was a distinct improvement for the silk samples treated with BTCA even after 30 times washing. In addition, the influence of the processing order of BTCA and silica sol treatment on the limiting oxygen index (LOI) of the finished silk fabric was also investigated. And the results demonstrated that the sample treated with BTCA first and then with the silica sol exhibited better LOI value (32.3%) than that of the sample by the conversed treatment order. Moreover the tensile property of treated samples was nearly unchanged, but the handle of sol treated

La imagen del cielo y los motivos de la creación del Sol en la mitología báltica

OpenAIRE

Laurinkienė, Nijolė

2008-01-01

Análisis de los motivos de la creación del Sol en los mitos cosmogónicos de Lituania y de Letonia. Estos mitos están comprendidos dentro del marco de la concepción general del Cielo. Son comparados los relatos bálticos sobre la creación con los de las mitologías finicas. The subject of the present article are the motifs of the creation of the Sun in Lithuanian and Latvian cosmogonic theories. These motifs are presented in the framework of the conception of heaven in its entirety. Baltic cr...

Proyecto integral Marina del Sol S.A.

Directory of Open Access Journals (Sweden)

Alfredo Palacios Barra

2008-11-01

Full Text Available El megaproyecto Marina del Sol del Gran Concepción, se emplaza en el sector del canal Ifarle a espaldas del Aeropuerto Carriel Sur en la comuna de Talcahuano. Recientemente entró a funcionar el Casino Marina del Sol, el que está inscrito en el marco de los 15 proyectos autorizados en el 2006 por la Superintendencia de Juego que buscan promover el desarrollo de este sector a nivel del país.

Asymmetric SOL Current in Vertically Displaced Plasma

Science.gov (United States)

Cabrera, J. D.; Navratil, G. A.; Hanson, J. M.

2017-10-01

Experiments at the DIII-D tokamak demonstrate a non-monotonic relationship between measured scrape-off layer (SOL) currents and vertical displacement event (VDE) rates with SOL currents becoming largely n=1 dominant as plasma is displaced by the plasma control system (PCS) at faster rates. The DIII-D PCS is used to displace the magnetic axis 10x slower than the intrinsic growth time of similar instabilities in lower single-null plasmas. Low order (n VDE instabilities observed when vertical control is disabled. Previous inquiry shows VDE asymmetry characterized by SOL current fraction and geometric parameters of tokamak plasmas. We note that, of plasmas displaced by the PCS, short displacement time scales near the limit of the PCS temporal control appear to result in larger n=1/n=2 asymmetries. Work supported under USDOE Cooperative Agreement DE-FC02-04ER54698 and DE-FG02-04ER54761.

Spirit Beside 'Home Plate,' Sol 1809

Science.gov (United States)

2009-01-01

NASA Mars Exploration Rover Spirit used its navigation camera to take the images assembled into this 120-degree view southward after a short drive during the 1,809th Martian day, or sol, of Spirit's mission on the surface of Mars (February 3, 2009). Spirit had driven about 2.6 meters (8.5 feet) that sol, continuing a clockwise route around a low plateau called 'Home Plate.' In this image, the rocks visible above the rovers' solar panels are on the slope at the northern edge of Home Plate. This view is presented as a cylindrical projection with geometric seam correction.

Optical sensing of HCl with phenol red doped sol-gels

International Nuclear Information System (INIS)

Wang Enju; Chow, Kwok-Fan; Wang Wenqun; Wong, Crystal; Yee, Cynthia; Persad, Alvin; Mann, Jonathan; Bocarsly, Andrew

2005-01-01

A dye doped sol-gel for the sensing of hydrochloric acid in solution and/or gaseous phase is described. The sol-gel is obtained by acidic hydrolysis of tetraethoxysilane (TEOS) and phenyltriethoxysilane (Ph-TriEOS) in the presence of phenol red (PR) and further spin-coating onto glass slides. The sensitive response is based on an increase of the absorption band at 510 nm of phenol red entrapped in the sol-gel casting when exposed to HCl solution or gas, due to protonation of the dye. The detection limit of the sol-gel response to moisturized gaseous HCl is below 12 ppm, and its response to HCl in solution falls in the range of 0.01-6 M. The sol-gel coating has a response time of less than 40 s in steady-state, and life-time of more than a year. Weak acids such as acetic acid, benzoic acid, salicylate acid, citrate acid, and carbonic acid do not interfere the response. The responses in acid solutions are completely reversible. In the gaseous phase, response of HCl appears to be moisture sensitive

Optical sensing of HCl with phenol red doped sol-gels

Energy Technology Data Exchange (ETDEWEB)

Wang Enju [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States)]. E-mail: wange@stjohns.edu; Chow, Kwok-Fan [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States); Wang Wenqun [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States); Wong, Crystal [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States); Yee, Cynthia [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States); Persad, Alvin [Department of Chemistry, St. John' s University, 8000 Utopia Parkway, Jamaica, NY 11439 (United States); Mann, Jonathan [Department of Chemistry, Princeton University, Princeton, NJ 08540 (United States); Bocarsly, Andrew [Department of Chemistry, Princeton University, Princeton, NJ 08540 (United States)

2005-04-08

A dye doped sol-gel for the sensing of hydrochloric acid in solution and/or gaseous phase is described. The sol-gel is obtained by acidic hydrolysis of tetraethoxysilane (TEOS) and phenyltriethoxysilane (Ph-TriEOS) in the presence of phenol red (PR) and further spin-coating onto glass slides. The sensitive response is based on an increase of the absorption band at 510 nm of phenol red entrapped in the sol-gel casting when exposed to HCl solution or gas, due to protonation of the dye. The detection limit of the sol-gel response to moisturized gaseous HCl is below 12 ppm, and its response to HCl in solution falls in the range of 0.01-6 M. The sol-gel coating has a response time of less than 40 s in steady-state, and life-time of more than a year. Weak acids such as acetic acid, benzoic acid, salicylate acid, citrate acid, and carbonic acid do not interfere the response. The responses in acid solutions are completely reversible. In the gaseous phase, response of HCl appears to be moisture sensitive.

Preparation of highly oriented Al:ZnO and Cu/Al:ZnO thin films by sol-gel method and their characterization

Energy Technology Data Exchange (ETDEWEB)

Vijayaprasath, G.; Murugan, R. [School of Physics, Alagappa University, Karaikudi 630 004, Tamil Nadu (India); Mahalingam, T. [Department of Electrical and Computer Engineering, Ajou University, Suwon 443-749 (Korea, Republic of); Hayakawa, Y. [Research Institute of Electronics, Shizuoka University, Hamamatsu 432-8011 (Japan); Ravi, G., E-mail: gravicrc@gmail.com [School of Physics, Alagappa University, Karaikudi 630 004, Tamil Nadu (India)

2015-11-15

Highly oriented thin films of Al doped ZnO (Al:ZnO) and Cu co-doped Al:ZnO (Cu/Al:ZnO) thin films were successfully deposited by sol–gel spin coating on glass substrates. The deposited films were characterized using X-ray diffraction analysis and found to exhibit hexagonal wurtzite structure with c-axis orientation. SEM images revealed that hexagonal rod shaped morphologies were grown perpendicular to the substrate surface due to repeated deposition process. High transmittance values were observed for pure ZnO compared to Al:ZnO and Cu/Al:ZnO thin films. The band gap widening is caused by the increase of carrier concentration, which is believed to be due to Burstein-Moss effect due to Al and Cu doping. PL spectra of Cu/Al:ZnO thin films indicate that the UV emission peaks slightly shifted towards lower energy side. XPS study was carried out for Zn{sub 0.80}Al{sub 0.10}Cu{sub 0.10}O thin films to analyze the binding energy of Al, Cu, Zn and O. Magnetic measurement studies exhibited ferromagnetic behavior at room temperature, which may be due to the increase in copper concentration in the doped films. The ferromagnetic behavior can be understood from the exchange coupling between localized ‘d’ spin of Cu ion mediated by free delocalized carriers. - Highlights: • High quality of Al:ZnO and Cu co-doped Al:ZnO thin films were fabricated by sol–gel method. • The XRD analyses revealed that the deposited thin films have hexagonal wurtzite structure. • XPS was carried out for Zn{sub 0.80}Al{sub 0.10}Cu{sub 0.10}O films to analyze the binding energy of Al, Cu, Zn and O. • SEM studies were made for Al:ZnO and Cu/Al:ZnO thin films. • RTFM was observed in Cu co-doped Al:ZnO thin films.

Contribución al debate sobre la educación y el mercado laboral en la administración pública en colombia

OpenAIRE

Hernández, Iván

2006-01-01

Este artículo contribuye al debate académico sobre los relevos en los cargos de la administración pública central en Colombia. Los resultados muestran algunas entidades públicas con ausencia de mecanismos de selección de mercado que generen relevos en la composición de cargos. Sin embargo, en otras entidades de la administración pública se evidencia un fortalecimiento de los mecanismos de selección de mercado, reflejado en un impacto real de los cambios en la calidad educativa (universitaria ...

La realidad al cuadrado : Representaciones sobre lo político en el humor gráfico del diario Clarín (1973-1983)

OpenAIRE

Levín, Florencia Paula

2015-01-01

En esta investigación se intenta bordear a partir del análisis sistemático de las representaciones sobre lo político construidas por el humor gráfico del diario Clarín, que por entonces ya era el matutino de mayor tirada a nivel nacional. Dado el amplio margen de inespecificidad y ambigüedad del término, es importante aclarar que cuando me refiero al "humor gráfico" del diario Clarín estoy aludiendo conjuntamente a los "cartoon" de Landrú publ...

Estudio sobre la evolución de los modelos mentales de estudiantes de 4º de ESO cuando observan, reflexionan y discuten sobre la combustión

Directory of Open Access Journals (Sweden)

Vanessa Sesto

2017-01-01

Full Text Available El propósito de este estudio fue analizar la evolución de los modelos mentales de estudiantes de secundaria sobre fenómenos que implican cambios en la materia al tener la oportunidad de observar, reflexionar y discutir sobre ellos. En trabajos anteriores ya se han identificado los modelos de los estudiantes sobre esta temática; sin embargo, aún se tiene poco conocimiento de cómo esos modelos evolucionan con la interacción social. Para alcanzar este objetivo se propuso como actividad la combustión de una vela dentro de un recipiente de cristal. Los participantes eran ocho estudiantes de 4º de ESO. La recogida de datos se realizó por medio de cuestionarios y grabaciones en audio y vídeo al realizar la actividad en pequeño grupo. Los resultados muestran una cierta evolución en los modelos. Al principio, los estudiantes utilizan los modelos de desaparición y transmutación. Después de la discusión, algunos estudiantes ya utilizan el modelo de reacción química.

Impact of an integrated core/SOL description on the R and B T optimization of tokamak fusion reactors

Science.gov (United States)

Siccinio, M.; Fable, E.; Angioni, C.; Saarelma, S.; Scarabosio, A.; Zohm, H.

2018-01-01

An updated and improved version of the 0D divertor and scrape-off layer (SOL) model published in Siccinio et al (2016 Plasma Phys. Control. Fusion 58 125011) was coupled with the 1.5D transport code ASTRA (Pereverzev 1991 IPP Report 5/42, Pereverzev and Yushmanov 2002 IPP Report 5/98 and Fable et al 2013 Plasma Phys. Control. Fusion 55 124028). The resulting numerical tool was employed for various scans in the major radius R and in the toroidal magnetic field B T—for different safety factors q, allowable loop voltages V loop and H factors—in order to identify the most convenient choices for an electricity producing tokamak. Such a scenario analysis was carried out evaluating self-consistently, and simultaneously, the core profile and transport effects, which significantly impact on the fusion power outcome, and the divertor heat loads, which represent one of the most critical issues in view of the realization of fusion power plants (Zohm et al 2013 Nucl. Fusion 53 073019 and Wenninger et al 2017 Nucl. Fusion 57 046002). The main result is that, when divertor limits are enforced, the curves at constant electrical power output are closed on themselves in the R-BT plane, and a maximum achievable power exists—i.e. no benefits would be obtained from a further increase in R and B T once the optimum is reached. This result appears as an intrinsic physical limit for all those devices where a radiative SOL is needed to deal with the power exhaust, and where a lower limit on the power crossing the separatrix (e.g. because of the L-H transition) is present.

Mécanique des sols et des roches

CERN Document Server

Vullier, Laurent; Zhao, Jian

2016-01-01

La mécanique des sols et la mécanique des roches sont des disciplines généralement traitées séparément dans la littérature. Pour la première fois, un traité réunit ces deux spécialités, en intégrant également les connaissances en lien avec les écoulements souterrains et les transferts thermiques. A la fois théorique et pratique, cet ouvrage propose tout d'abord une description détaillée de la nature et de la composition des sols et des roches, puis s'attache à la modélisation de problèmes aux conditions limites et présente les essais permettant de caractériser les sols et les roches, tant d'un point de vue mécanique qu'hydraulique et thermique. La problématique des sols non saturés et des écoulements multiphasiques est également abordée. Une attention particulière est portée aux lois de comportement mécanique et à la détermination de leurs paramètres par des essais in situ et en laboratoire, et l'ouvrage offre également une présentation détaillée des systèmes de classi...

Fabrication of indium tin oxide (ITO) thin film with pre-treated sol coating

International Nuclear Information System (INIS)

Hong, Sung-Jei; Han, Jeong-In

2004-01-01

A new pre-treated sol-coating method to fabricate an indium tin oxide (ITO) thin film is introduced in this paper. The pre-treatment sol-coating method is to form a seed layer on the substrate before spin coating of ITO sol. The pre-treatment was carried out at room temperature in order not to damage the substrate during the pre-treatment. It is effective to enhance the formation of the ITO sol film on the substrate, owing to the seed layer. The seed layer consists of ultrafine grains, which are observed at the pre-treated substrate. For the optimal pre-treatment condition, we used pre-treatment times of 24, 48, 72, and 96 hours to observe the effect on the characteristics of ITO sol film. As a result, the lowest resistance could be achieved with a pre-treatment time of 72 hours. The optical transmittance of the ITO sol film with the pre-treatment time of 72 hours exceeded 80 % at a wavelength of 400 nm. So, an ITO sol film with good electrical and optical properties could be fabricated by using the pretreatment sol coating.

Validación del cuestionario de medida del conocimiento del paciente sobre su medicamento adaptado al portugués

Directory of Open Access Journals (Sweden)

Joaquín Salmerón Rubio

2014-04-01

Full Text Available Validación de un cuestionario adaptado transculturalmente al portugués en cinco farmacias comunitarias de Portugal. Se determino la capacidad discriminante de los ítems, la validez de contenido y de constructo, análisis factorial de componentes principales, la fiabilidad y su estabilidad. Se observó un elevado grado de equivalencia semántica entre el cuestionario original y el cuestionario adaptado transculturalmente al portugués. Se obtuvo un índice de Kaiser-Meyer-Olkin de 0.550, y el test de esferidad de Bartlett confirmó la adecuación de los datos para la aplicación del análisis factorial (p < 0.0001. Se consideraron 3 factores que explicaron el 52.6% de la variabilidad total. Con respecto a la fiabilidad se obtuvo un á de Cronbach de 0.519, un C.Kappa = 0.89 y CCI = 0.756 (IC = 0.598-0.963. En este trabajo se elabora la primera adaptación para la cultura portuguesa de un cuestionario específico para medir el grado de conocimiento que tienen los pacientes sobre los medicamentos.

Analyses of laser and furnace treated sol-gel coatings

NARCIS (Netherlands)

De Hosson, JT; De Haas, M; Sudarshan, TS; Jeandin, M; Khor, KA

1998-01-01

Here we explore a new method that allows thin films to be made with almost any composition and degree of porosity by means of a combination of sol-gel and laser technology. Results are presented for furnace and laser treated TEOTI-(tetraethylorthotitanate as sol precursor) coated silicon samples.

Resistencia al cizallamiento de una resina compuesta al aplicar diferentes agentes blanqueadores y su efecto sobre la microestructura del esmalte

OpenAIRE

Cornejo Peña, María Antonieta

2014-01-01

Muchos han sido los estudios que se han reportado acerca del efecto de sustancias aclaradoras sobre la adhesión y estructura del esmalte, sin embargo, poco se ha reportado sobre las alteraciones morfológicas de la estructura exterior del esmalte después del blanqueamiento. A pesar de la reducción de la microdureza del esmalte se ha informado que esta alteración no es sólo por el procedimiento de blanqueamiento, sino también por el pH de la fórmula utilizada. Algunos estudios no han encontrado...

El impacto del Impuesto al Valor Agregado sobre el gasto en Colombia

Directory of Open Access Journals (Sweden)

Jorge Tovar

2008-07-01

Full Text Available Este trabajo cuantifica el impacto del IVA sobre el gasto de los hogares utilizando la enorme variación relativa del IVA en Colombia como estrategia de identificación. Para tal efecto se correlaciona el IVA con el gasto de los hogares según se reporta en la Encuesta Continua de Hogares (ECH. La estimación se realiza para tres rubros de gasto presente en la ECH: alimentación, cultura y entretenimiento y celulares. Los resultados sugieren que un incremento del IVA tiene impactos positivos en el gasto de alimentos y celulares, y negativos en el de cultura y esparcimiento. Además, el ejercicio muestra que incrementar el IVA tiene un impacto diferencial, sobre hogares de distintas características demográficas y económicas.

IMPACTO DE LA EXPRESIÓN CORPORAL SOBRE LAS EMOCIONES EN EL ÁMBITO EDUCATIVO

Directory of Open Access Journals (Sweden)

Barriopedro Moro María Isabel

2010-10-01

Full Text Available

Numerosos autores desde la Expresión Corporal han puesto de manifiesto cómo esta disciplina puede contribuir al desarrollo de la dimensión emocional y social del individuo, en definitiva al desarrollo afectivo del alumno. El objetivo del presente trabajo fue evaluar el cambio sobre el Bienestar Psicológico y sobre las Habilidades Sociales producido como consecuencia de la asignatura de Expresión Corporal en alumnos universitarios mediante un estudio experimental. Los resultados sólo mostraron cambios con respecto al bienestar material en dos de los tres grupos experimentales y ningún efecto de la impartición de esta asignatura sobre el Bienestar Subjetivo y las Habilidades Sociales de los sujetos. Estos resultados son incompatibles con las afirmaciones que realizan la mayor parte de los autores de este campo.
Palabras claves: Emociones, Expresión Corporal, Bienestar psicológico y Habilidades sociales.

Planteamientos sobre la pobreza: una aproximación conceptual

Directory of Open Access Journals (Sweden)

Bertha Lucía Martínez Bernal

2015-07-01

Full Text Available En el presente artículo se presentan varias definiciones o conceptos para la comprensión, medición y el análisis de la pobreza. Para ello se retoma la producción escrita de diferentes estudiosos e investigadores que han hecho aportes valiosos sobre el tema. Al lado de estos conceptos se analizan los diferentes enfoques que se utilizan para aproximarse al estudio de la pobreza, aunque estas no son teorías ni explicaciones de sus causas, sino perspectivas sobre pobreza que denotan dichos enfoques. Así mismo se desarrolla una revisión de las metodologías más utilizadas en los procesos de identificación y agregación. Finalmente se interpretan las políticas públicas en los sectores sociales.

La gran vida al aire libre PSA (:30) (The Great Outdoors)

Centers for Disease Control (CDC) Podcasts

2016-05-31

Un hombre y una mujer se están alistando para irse a una caminata. La mujer le recuerda al hombre que se proteja del sol.  Created: 5/31/2016 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 5/31/2016.

¿El armario está abierto?: estudios sobre diversidad sexual en El Salvador

Directory of Open Access Journals (Sweden)

Amaral Palevi Gómez Arévalo

2017-12-01

Full Text Available El presente texto tiene por objetivo analizar 39 producciones universitarias sobre diferentes temáticas de diversidad sexual producidas entre 1988 a 2015, las cuales se organizan en 4 ejes/binomios: Prácticas sexuales/Cuerpos, Matrimonio/Familias, Identidades/Prejuicios y Derechos/Ciudadanías. Al mismo tiempo se proponen nuevas temáticas para investigar y se reflexiona sobre los retos al interior de la educación superior salvadoreña para constituir un campo de Estudios sobre Diversidad Sexual. Concluyendo, a pesar de la existencia dispersa de 39 producciones universitarias, las cuales son un avance, el armario de la academia salvadoreña está aún cerrado, y por tal motivo surge la pregunta ¿cómo lo podemos abrir?

Bactericidal micron-thin sol-gel films prevent pin tract and periprosthetic infection.

Science.gov (United States)

Qu, Haibo; Knabe, Christine; Burke, Megan; Radin, Shula; Garino, Jonathan; Schaer, Thomas; Ducheyne, Paul

2014-08-01

Orthopedic injuries constitute the majority of wounds sustained by U.S. soldiers in recent conflicts. The risk of infection is considerable with fracture fixation devices. In this pilot study, we examined the use of unique bactericidal micron-thin sol-gel films on fracture fixation devices and their ability to prevent and eradicate infections. External fixation was studied with micron-thin sol-gel coated percutaneous pins releasing triclosan and inserted medially into rabbit tibiae. A total of 11 rabbits received percutaneous pins that were either uncoated or sol-gel/triclosan coated. Internal fracture fixation was also studied using sol-gel coated intramedullary (IM) nails releasing vancomycin in the intramedullary tibiae. Six sheep received IM nails that were coated with a sol-gel film that either contained vancomycin or did not contain vancomycin. All animals were challenged with Staphylococcus aureus around the implant. Animals were euthanized at 1 month postoperative. Rabbits receiving triclosan/sol-gel coated percutaneous pins did not show signs of infection. Uncoated percutaneous pins had a significantly higher infection rate. In the sheep study, there were no radiographic signs of osteomyelitis with vancomycin/sol-gel coated IM nails, in contrast to the observations in the control cohort. Hence, the nanostructured sol-gel controlled release technology offers the promise of a reliable and continuous delivery system of bactericidals from orthopedic devices to prevent and treat infection. Reprint & Copyright © 2014 Association of Military Surgeons of the U.S.

Ionogel Electrolytes through Sol-Gel Processing

Science.gov (United States)

Horowitz, Ariel I.

Electrical energy needs have intensified due to the ubiquity of personal electronics, the decarbonization of energy services through electrification, and the use of intermittent renewable energy sources. Despite developments in mechanical and thermal methods, electrochemical technologies are the most convenient and effective means of storing electrical energy. These technologies include both electrochemical cells, commonly called batteries, and electrochemical double-layer capacitors, or "supercapacitors", which store energy electrostatically. Both device types require an ion-conducting electrolyte. Current devices use solutions of complex salts in organic solvents, leading to both toxicity and flammability concerns. These drawbacks can be avoided by replacing conventional electrolytes with room-temperature molten salts, known as ionic liquids (ILs). ILs are non-volatile, non-flammable, and offer high conductivity and good electrochemical stability. Device mass can be reduced by combining ILs with a solid scaffold material to form an "ionogel," further improving performance metrics. In this work, sol-gel chemistry is explored as a means of forming ionogel electrolytes. Sol-gel chemistry is a solution-based, industrially-relevant, well-studied technique by which solids such as silica can be formed in situ. Previous works used a simple acid-catalyzed sol-gel reaction to create brittle, glassy ionogels. Here, both the range of products that can be accomplished through sol-gel processing and the understanding of interactions between ILs and the sol-gel reaction network are greatly expanded. This work introduces novel ionogel materials, including soft and compliant silica-supported ionogels and PDMS-supported ionogels. The impacts of the reactive formulation, IL identity, and casting time are detailed. It is demonstrated that variations in formulation can lead to rapid gelation and open pore structures in the silica scaffold or slow gelation and more dense silica

Introducción al tema monográfico

Directory of Open Access Journals (Sweden)

Sofía Salas Ibarra

2009-06-01

Full Text Available Este número de Ars Medica está por entero dedicado al tema de Anticoncepción de Emergencia (AE y a la discusión de sus aspectos biológicos, éticos, sociales y jurídicos, incluyendo un análisis sobre los aspectos científicos y jurídicos contenidos en el reciente fallo del Tribunal Constitucional de Chile. Como es de conocimiento público, con fecha 18 de abril de 2008 dicho tribunal dictó sentencia sobre el requerimiento presentado por un grupo de diputados en contra del decreto supremo Nº 48 de 2007 del Ministerio de Salud, el cual prohíbe la entrega de AE en los servicios públicos de salud. Pocos días después, el Gobierno de Chile declaró la supresión de las normas sobre AE de las Normas Nacionales sobre Regulación de la Fertilidad, que forman parte del decreto supremo Nº 48, de 2007, del Ministerio de Salud, por ser inconstitucionales de acuerdo al fallo antes señalado1

Protección contra la corrosión de aleaciones de aluminio mediante recubrimientos sol-gel

Directory of Open Access Journals (Sweden)

Conde, A.

2002-06-01

Full Text Available Present paper studies the corrosion protection of three new nanomeric coatings obtained from modified silanes and cured at low temperatures. The synthesis of these coatings is carried out starting from a mixture of two sols separately prepared: a prehydrolized GPTS (glicidoxipropiltrimetoxisilano and a second sol TEOS/MTES. Adding to this initial sol a colloidal solution of 25% in weight of commercial particles of SiO2, Aerosil 300 and Aerosil R972 respectively can be obtained thicker nanomeric coatings. Once synthesized, they were deposited by means of the spin coating method onto two aluminum alloys, 5555 and 3005 used as substrates. The final thickness of the coatings is about 10 μm, for the coating without particles and slightly higher, 12-14 μm approximately, for the coatings with particles. The electrochemical results indicated that, in all cases, the coated samples presented an improvement in the corrosion behavior in comparison with bare alloys in aggressive media of NaCl. The corrosion rate decreased three orders of magnitude for the coatings with particles and lower for those that do not contain particles.

En el presente trabajo se estudia la protección frente a la corrosión que proporcionan tres nuevos recubrimientos nanoméricos de baja temperatura de curado obtenidos a partir de silanos modificados. La síntesis de estos recubrimientos se realiza a partir de una mezcla de dos soles, GPTS (glicidoxipropiltrimetoxisilano prehidrolizado y un segundo sol TEOS/MTES. Añadiendo a este sol inicial una disolución coloidal de partículas se obtienen recubrimientos nanoméricos de mayor espesor. En el presente trabajo los recubrimientos particulados se obtuvieron incorporando un 25% en peso de partículas comerciales de SiO2, Aerosil 300 y Aerosil R972 respectivamente. Una vez sintetizados, se depositaron mediante el método de centrifugado, sobre dos aleaciones de aluminio, 5555 y 3005 empleadas como substratos. El espesor final

Sol-gel bonding of silicon wafers

International Nuclear Information System (INIS)

Barbe, C.J.; Cassidy, D.J.; Triani, G.; Latella, B.A.; Mitchell, D.R.G.; Finnie, K.S.; Bartlett, J.R.; Woolfrey, J.L.; Collins, G.A.

2005-01-01

Low temperature bonding of silicon wafers was achieved using sol-gel technology. The initial sol-gel chemistry of the coating solution was found to influence the mechanical properties of the resulting bonds. More precisely, the influence of parameters such as the alkoxide concentration, water-to-alkoxide molar ratio, pH, and solution aging on the final bond morphologies and interfacial fracture energy was studied. The thickness and density of the sol-gel coating were characterised using ellipsometry. The corresponding bonded specimens were investigated using attenuated total reflectance Fourier transformed infrared spectroscopy to monitor their chemical composition, infrared imaging to control bond integrity, and cross-sectional transmission electron microscopy to study their microstructure. Their interfacial fracture energy was measured using microindentation. An optimum water-to-alkoxide molar ratio of 10 and hydrolysis water at pH = 2 were found. Such conditions led to relatively dense films (> 90%), resulting in bonds with a fracture energy of 3.5 J/m 2 , significantly higher than those obtained using classical hydrophilic bonding (typically 1.5-2.5 J/m 2 ). Ageing of the coating solution was found to decrease the bond strength

Opportunity's View After Long Drive on Sol 1770 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 104 meters (341 feet) on the 1,770th Martian day, or sol, of Opportunity's surface mission (January 15, 2009). This view is presented as a vertical projection with geometric seam correction. North is at the top. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Prior to the Sol 1770 drive, Opportunity had driven less than a meter since Sol 1713 (November 17, 2008), while it used the tools on its robotic arm first to examine a meteorite called 'Santorini' during weeks of restricted communication while the sun was nearly in line between Mars and Earth, then to examine bedrock and soil targets near Santorini. The rover's position after the Sol 1770 drive was about 1.1 kilometer (two-thirds of a mile) south southwest of Victoria Crater. Cumulative odometry was 13.72 kilometers (8.53 miles) since landing in January 2004, including 1.94 kilometers (1.21 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008).

Opportunity's View After Long Drive on Sol 1770 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 104 meters (341 feet) on the 1,770th Martian day, or sol, of Opportunity's surface mission (January 15, 2009). This view is presented as a polar projection with geometric seam correction. North is at the top. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Prior to the Sol 1770 drive, Opportunity had driven less than a meter since Sol 1713 (November 17, 2008), while it used the tools on its robotic arm first to examine a meteorite called 'Santorini' during weeks of restricted communication while the sun was nearly in line between Mars and Earth, then to examine bedrock and soil targets near Santorini. The rover's position after the Sol 1770 drive was about 1.1 kilometer (two-thirds of a mile) south southwest of Victoria Crater. Cumulative odometry was 13.72 kilometers (8.53 miles) since landing in January 2004, including 1.94 kilometers (1.21 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008).

ENTORNOS MPLS Y ATM PARA EL TRANSPORTE DE VOZ SOBRE INTERNET

Directory of Open Access Journals (Sweden)

Nancy Yaneth Gelvez García

2012-08-01

Full Text Available Este artículo presenta los resultados obtenidos en el estudio de la calidad de servicio sobre redes IP en tráficos sensibles al retardo como la VoIP sobre la tecnología ATM y MPLS. Se analizaran diferentes topologías con características propias que permitirán evaluar valores tales como el retardo y el ancho de banda.

Human SolCD39 Inhibits Injury-induced Development of Neointimal Hyperplasia

Science.gov (United States)

Drosopoulos, Joan H. F.; Kraemer, Rosemary; Shen, Hao; Upmacis, Rita K.; Marcus, Aaron J.; Musi, Elgilda

2010-01-01

SUMMARY Blood platelets provide the initial response to vascular endothelial injury, becoming activated as they adhere to the injured site. Activated platelets recruit leukocytes, and initiate proliferation and migration of vascular smooth muscle cells (SMC) within the injured vessel wall, leading to development of neointimal hyperplasia. Endothelial CD39/NTPDase1 and recombinant solCD39 rapidly metabolize nucleotides, including stimulatory ADP released from activated platelets, thereby suppressing additional platelet reactivity. Using a murine model of vascular endothelial injury, we investigated whether circulating human solCD39 could reduce platelet activation and accumulation, thus abating leukocyte infiltration and neointimal formation following vascular damage. Intraperitoneally-administered solCD39 ADPase activity in plasma peaked 1 hr post-injection, with an elimination half-life of 43 hr. Accordingly, mice were administered solCD39 or saline 1 hr prior to vessel injury, then either sacrificed 24 hr post-injury or treated with solCD39 or saline (3X weekly) for an additional 18 days. 24 hr post-injury, solCD39-treated mice displayed a reduction in platelet activation and recruitment, P-selectin expression, and leukocyte accumulation in the arterial lumen. Furthermore, repeated administration of solCD39 modulated the late stage of vascular injury by suppressing leukocyte deposition, macrophage infiltration and SMC proliferation/migration, resulting in abrogation of neointimal thickening. In contrast, injured femoral arteries of saline-injected mice exhibited massive platelet thrombus formation, marked P-selectin expression, and leukocyte infiltration. Pronounced neointimal growth with macrophage and SMC accretion was also observed (intimal-to-medial area ratio 1.56±0.34 at 19 days). Thus, systemic administration of solCD39 profoundly affects injury-induced cellular responses, minimizing platelet deposition and leukocyte recruitment, and suppressing

Permanent Habitats in Earth-Sol/Mars-Sol Orbit Positions

Science.gov (United States)

Greenspon, J.

Project Outpost is a manned Earth-Sol/Mars-Sol platform that enables permanent occupation in deep space. In order to develop the program elements for this complex mission, Project Outpost will rely primarily on existing/nearterm technology and hardware for the construction of its components. For the purposes of this study, four mission requirements are considered: 1. Outpost - Man's 1st purpose-produced effort of space engineering, in which astructure is developed/constructed in an environment completely alien to currentpractices for EVA guidelines. 2. Newton - a concept study developed at StarGate Research, for the development ofa modified Hohmann personnel orbital transport operating between Earth andMars. Newton would serve as the primary crew delivery apparatus throughrepeatable transfer scheduling for all Earth-Lpoint-Mars activities. Thispermanent "transit system" would establish the foundations for Solar systemcolonization. 3. Cruis - a concept study developed at StarGate Research, for the development of amodified Hohmann cargo orbital transport operating between Earth and Mars.Cruis would serve as the primary equipment delivery apparatus throughrepeatable transfer scheduling for all Earth-Lpoint-Mars activities. Thispermanent "transit system" would establish the foundations for Solar systemcolonization, and 4. Ares/Diana - a more conventional space platform configuration for Lunar andMars orbit is included as a construction baseline. The operations of these assetsare supported, and used for the support, of the outpost. Outpost would be constructed over a 27-year period of launch opportunities into Earth-Sol or Mars-Sol Lagrange orbit (E-S/M-S L1, 4 or 5). The outpost consists of an operations core with a self-contained power generation ability, a docking and maintenance structure, a Scientific Research complex and a Habitation Section. After achieving initial activation, the core will provide the support and energy required to operate the outpost in a 365

INFLUENCIA DE LOS RECUBRIMIENTOS DÚPLEX SOBRE LAS PROPIEDADES MECÁNICAS Y RESISTENCIA AL DESGASTE DEL ACERO AISI 4140 BONIFICADO

Directory of Open Access Journals (Sweden)

Francisco Javier Bolívar Osorio

Full Text Available El acero AISI 4140 es un acero de baja aleación al cromo/molibdeno de elevada resistencia mecánica y buena tenacidad, el cual se utiliza para la fabricación de piezas de maquinaria como piñones, cigüeñales, ejes de levas, etc. Sin embargo, su resistencia al desgaste es bastante limitada y suele ser mejorada mediante el tratamiento superficial de la nitruración. El propósito de este trabajo consistió en mejorar las propiedades mecánicas e incrementar la resistencia al desgaste del acero 4140 mediante la aplicación de un tratamiento superficial DUPLEX consistente en la nitruración líquida (conocida como Teniffer seguido del depósito de un recubrimiento duro de nitruro de titanio (TiN. La microestructura cristalina fue evaluada mediante difracción de rayos X, la morfología y la composición química fue determinada por microscopía SEM y espectroscopía de energía dispersiva de rayos X (EDS, las propiedades tribológicas fueron analizadas mediante mediciones en un tribómetro de tipo esfera sobre disco y la microdureza se determinó por el método Vickers. Las muestras tratadas con el recubrimiento dúplex mostraron una resistencia al desgaste 4 veces mayor que la muestra en estado bonificado, lo cual demuestra la aplicación potencial que tiene el acero 4140 sometido a este tratamiento dúplex.

Opportunity's Surroundings on Sol 1818 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. This view is presented as a vertical projection with geometric seam correction. North is at the top. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

Opportunity's Surroundings on Sol 1818 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. This view is presented as a polar projection with geometric seam correction. North is at the top. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

Neutron detector using sol-gel absorber

Science.gov (United States)

Hiller, John M.; Wallace, Steven A.; Dai, Sheng

1999-01-01

An neutron detector composed of fissionable material having ions of lithium, uranium, thorium, plutonium, or neptunium, contained within a glass film fabricated using a sol-gel method combined with a particle detector is disclosed. When the glass film is bombarded with neutrons, the fissionable material emits fission particles and electrons. Prompt emitting activated elements yielding a high energy electron contained within a sol-gel glass film in combination with a particle detector is also disclosed. The emissions resulting from neutron bombardment can then be detected using standard UV and particle detection methods well known in the art, such as microchannel plates, channeltrons, and silicon avalanche photodiodes.

Integrated simulation of ELM energy loss determined by pedestal MHD and SOL transport

International Nuclear Information System (INIS)

Hayashi, N.; Takizuka, T.; Ozeki, T.; Aiba, N.; Oyama, N.

2007-01-01

An integrated simulation code TOPICS-IB based on a transport code with a stability code for the peeling-ballooning modes and a scrape-off-layer (SOL) model has been developed to clarify self-consistent effects of edge localized modes (ELMs) and the SOL on the plasma performance. Experimentally observed collisionality dependence of the ELM energy loss is found to be caused by both the edge bootstrap current and the SOL transport. The bootstrap current decreases with an increase in collisionality and intensifies the magnetic shear at the pedestal region. The increase in the magnetic shear reduces the width of eigenfunctions of unstable modes, which results in the reduction of both the area of the ELM enhanced transport and the ELM enhanced transport near the separatrix. On the other hand, when an ELM crash occurs, the energy flows into the SOL and the SOL temperature rapidly increases. The increase in the SOL temperature lowers the ELM energy loss due to the flattening of the radial edge gradient. The parallel electron heat conduction determines how the SOL temperature increases. For higher collisionality, the conduction becomes lower and the SOL electron temperature increases more. By the above two mechanisms, the ELM energy loss decreases with increasing collisionality

Mesure de la vitesse d'infiltration des eaux dans le sol : Cas des sols ...

African Journals Online (AJOL)

SARAH

30 avr. 2016 ... Pour ceux, il est nécessaire d'opter pour une agriculture moderne ... à une telle agriculture. Mots clés : mesure, vitesse, infiltration, sols, pollutions, eau, Niari, Congo .... une porosité tubulaire d'origine biologique. Toutes ces.

Evolution of heterogeneity accompanying sol-gel transitions in a supramolecular hydrogel.

Science.gov (United States)

Matsumoto, Yuji; Shundo, Atsuomi; Ohno, Masashi; Tsuruzoe, Nobutomo; Goto, Masahiro; Tanaka, Keiji

2017-10-18

When a peptide amphiphile is dispersed in water, it self-assembles into a fibrous network, leading to a supramolecular hydrogel. When the gel is physically disrupted by shaking, it transforms into a sol state. After aging at room temperature for a while, it spontaneously returns to the gel state, called sol-gel transition. However, repeating the sol-gel transition often causes a change in the rheological properties of the gel. To gain a better understanding of the sol-gel transition and its reversibility, we herein examined the thermal motion of probe particles at different locations in a supramolecular hydrogel. The sol obtained by shaking the gel was heterogeneous in terms of the rheological properties and the extent decreased with increasing aging time. This time course of heterogeneity, or homogeneity, which corresponded to the sol-to-gel transition, was observed for the 1st cycle. However, this was not the case for the 2nd and 3rd cycles; the heterogeneity was preserved even after aging. Fourier-transform infrared spectroscopy, small-angle X-ray scattering, and atomic force and confocal laser scanning microscopies revealed that, although the molecular aggregation states of amphiphiles both in the gel and sol remained unchanged with the cycles, the fibril density diversified to high and low density regions even after aging. The tracking of particles with different sizes indicated that the partial mesh size in the high density region and the characteristic length scale of the density fluctuation were smaller than 50 nm and 6 μm, respectively.

Entrapment of subtilisin in ceramic sol-gel coating for antifouling applications.

Science.gov (United States)

Regina, Viduthalai Rasheedkhan; Søhoel, Helmer; Lokanathan, Arcot Raghupathi; Bischoff, Claus; Kingshott, Peter; Revsbech, Niels Peter; Meyer, Rikke Louise

2012-11-01

Enzymes with antifouling properties are of great interest in developing nontoxic antifouling coatings. A bottleneck in developing enzyme-based antifouling coatings is to immobilize the enzyme in a suitable coating matrix without compromising its activity and stability. Entrapment of enzymes in ceramics using the sol-gel method is known to have several advantages over other immobilization methods. The sol-gel method can be used to make robust coatings, and the aim of this study was to explore if sol-gel technology can be used to develop robust coatings harboring active enzymes for antifouling applications. We successfully entrapped a protease, subtilisin (Savinase, Novozymes), in a ceramic coating using a sol-gel method. The sol-gel formulation, when coated on a stainless steel surface, adhered strongly and cured at room temperature in less than 8 h. The resultant coating was smoother and less hydrophobic than stainless steel. Changes in the coating's surface structure, thickness and chemistry indicate that the coating undergoes gradual erosion in aqueous medium, which results in release of subtilisin. Subtilisin activity in the coating increased initially, and then gradually decreased. After 9 months, 13% of the initial enzyme activity remained. Compared to stainless steel, the sol-gel-coated surfaces with active subtilisin were able to reduce bacterial attachment of both Gram positive and Gram negative bacteria by 2 orders of magnitude. Together, our results demonstrate that the sol-gel method is a promising coating technology for entrapping active enzymes, presenting an interesting avenue for enzyme-based antifouling solutions.

Collisionality dependent transport in TCV SOL plasmas

DEFF Research Database (Denmark)

Garcia, Odd Erik; Pitts, R.A.; Horacek, J.

2007-01-01

Results are presented from probe measurements in the low field side scrape-off layer (SOL) region of TCV during plasma current scan experiments. It is shown that with decreasing plasma current the radial particle density profile becomes broader and the fluctuation levels and turbulence driven...... radial particle flux increase. In the far SOL the fluctuations exhibit a high degree of statistical similarity and the particle density and flux at the wall radius scale inversely with the plasma current. Together with previous TCV density scan experiments, this indicates that plasma fluctuations...

Opportunity's View After Drive on Sol 1806 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 60.86 meters (200 feet) on the 1,806th Martian day, or sol, of Opportunity's surface mission (Feb. 21, 2009). North is at the center; south at both ends. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Engineers designed the Sol 1806 drive to be driven backwards as a strategy to redistribute lubricant in the rovers wheels. The right-front wheel had been showing signs of increased friction. The rover's position after the Sol 1806 drive was about 2 kilometer (1.2 miles) south southwest of Victoria Crater. Cumulative odometry was 14.74 kilometers (9.16 miles) since landing in January 2004, including 2.96 kilometers (1.84 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a polar projection with geometric seam correction.

Opportunity's View After Drive on Sol 1806 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings just after driving 60.86 meters (200 feet) on the 1,806th Martian day, or sol, of Opportunity's surface mission (Feb. 21, 2009). North is at the center; south at both ends. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Engineers designed the Sol 1806 drive to be driven backwards as a strategy to redistribute lubricant in the rovers wheels. The right-front wheel had been showing signs of increased friction. The rover's position after the Sol 1806 drive was about 2 kilometer (1.2 miles) south southwest of Victoria Crater. Cumulative odometry was 14.74 kilometers (9.16 miles) since landing in January 2004, including 2.96 kilometers (1.84 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a vertical projection with geometric seam correction.

Sol-gel open tubular ODS columns with reversed electroosmotic flow for capillary electrochromatography.

Science.gov (United States)

Hayes, J D; Malik, A

2001-03-01

Sol-gel chemistry was successfully used for the fabrication of open tubular columns with surface-bonded octadecylsilane (ODS) stationary-phase coating for capillary electrochromatography (OT-CEC). Following column preparations, a series of experiments were performed to investigate the performance of the sol-gel coated ODS columns in OT-CEC. The incorporation of N-octadecyldimethyl[3-(trimethoxysilyl)propyl]ammonium chloride as one of the sol-gel precursors played an important role in the electrochromatographic performance of the prepared columns. This chemical reagent possesses a chromatographically favorable, bonded ODS moiety, in conjunction with three methoxy groups allowing for sol-gel reactivity. In addition, a positively charged nitrogen atom is present in the molecular structure of this reagent and provides a positively charged capillary surface responsible for the reversed electroosmotic flow (EOF) in the columns during CEC operation. Comparative studies involving the EOF within such sol-gel ODS coated and uncoated capillaries were performed using acetonitrile and methanol as the organic modifiers in the mobile phase. The use of a deactivating reagent, phenyldimethylsilane, in the sol-gel solution was evaluated. Efficiency values of over 400,000 theoretical plates per meter were achieved in CEC on a 64 cm x 25 microm i.d. sol-gel ODS open tubular column. Test mixtures of polycyclic aromatic hydrocarbons, benzene derivatives, and aromatic aldehydes and ketones were used to evaluate the CEC performances of both nondeactivated and deactivated open tubular sol-gel columns. The effects of mobile-phase organic modifier contents and pH on EOF in such columns were evaluated. The prepared sol-gel ODS columns are characterized by switchable electroosmotic flow. A pH value of approximately 8.5 was found correspond to the isoelectric point for the prepared sol-gel ODS coatings.

The effect of synthetic method and annealing temperature on metal site preference in Al(1-x)Ga(x)FeO3.

Science.gov (United States)

Walker, James D S; Grosvenor, Andrew P

2013-08-05

Magnetoelectric materials couple both magnetic and electronic properties, making them attractive for use in multifunctional devices. The magnetoelectric AFeO3 compounds (Pna2(1); A = Al, Ga) have received attention as the properties of the system depend on composition as well as the synthetic method used. Al(1-x)Ga(x)FeO3. (0 ≤ x ≤ 1) was synthesized by the sol-gel and coprecipitation methods and studied by X-ray absorption near-edge spectroscopy (XANES). Al L(2,3-), Ga K-, and Fe K-edge XANES spectra were collected to examine how the average metal coordination number (CN) changes with the synthetic method. Al and Fe were found to prefer octahedral sites, while Ga prefers the tetrahedral site. It was found that composition played a larger role in determining site occupancies than synthetic method. Samples made by the sol-gel or ceramic methods (reported previously; Walker, J. D. S.; Grosvenor, A. P. J. Solid State Chem. 2013, 197, 147-153) showed smaller spectral changes than samples made via the coprecipitation method. This is attributed to greater ion mobility in samples synthesized via coprecipitation as the reactants do not have a long-range polymeric or oxide network during synthesis like samples synthesized via the sol-gel or ceramic method. Increasing annealing temperature increases the average coordination number of Al, and to a lesser extent Ga, while the average coordination number of Fe decreases. This study indicates that greater disorder is observed when the Al(1-x)Ga(x)FeO3. compounds have high Al content, and when annealed at higher temperatures.

Electrical characterization of γ-Al2O3 thin film parallel plate capacitive sensor for trace moisture detection

Science.gov (United States)

Kumar, Lokesh; Kumar, Shailesh; Khan, S. A.; Islam, Tariqul

2012-10-01

A moisture sensor was fabricated based on porous thin film of γ-Al2O3 formed between the parallel gold electrodes. The sensor works on capacitive technique. The sensing film was fabricated by dipcoating of aluminium hydroxide sol solution obtained from the sol-gel method. The porous structure of the film of γ-Al2O3 phase was obtained by sintering the film at 450 °C for 1 h. The electrical parameters of the sensor have been determined by Agilent 4294A impedance analyzer. The sensor so obtained is found to be sensitive in moisture range 100-600 ppmV. The response time of the sensor in ppmV range moisture is very low ~ 24 s and recovery time is ~ 37 s.

Reflexiones sobre el concepto de justicia

Directory of Open Access Journals (Sweden)

Víctor C. Pascual Planchuelo

2005-06-01

Full Text Available Este ensayo constituye una reflexión sobre el concepto de Justicia. No se centra, como tantos estudios al respecto, en el plano teórico y metafísico, sino que atiende problemas de mayor actualidad: la opinión de los ciudadanos, la postura de los profesionales y otros asuntos controvertidos del ámbito del Derecho.

SOL: A Library for Scalable Online Learning Algorithms

OpenAIRE

Wu, Yue; Hoi, Steven C. H.; Liu, Chenghao; Lu, Jing; Sahoo, Doyen; Yu, Nenghai

2016-01-01

SOL is an open-source library for scalable online learning algorithms, and is particularly suitable for learning with high-dimensional data. The library provides a family of regular and sparse online learning algorithms for large-scale binary and multi-class classification tasks with high efficiency, scalability, portability, and extensibility. SOL was implemented in C++, and provided with a collection of easy-to-use command-line tools, python wrappers and library calls for users and develope...

Spirit Near 'Stapledon' on Sol 1802

Science.gov (United States)

2009-01-01

NASA Mars Exploration Rover Spirit used its navigation camera for the images assembled into this full-circle view of the rover's surroundings during the 1,802nd Martian day, or sol, (January 26, 2009) of Spirit's mission on the surface of Mars. South is at the center; north is at both ends. Spirit had driven down off the low plateau called 'Home Plate' on Sol 1782 (January 6, 2009) after spending 12 months on a north-facing slope on the northern edge of Home Plate. The position on the slope (at about the 9-o'clock position in this view) tilted Spirit's solar panels toward the sun, enabling the rover to generate enough electricity to survive its third Martian winter. Tracks at about the 11-o'clock position of this panorama can be seen leading back to that 'Winter Haven 3' site from the Sol 1802 position about 10 meters (33 feet) away. For scale, the distance between the parallel wheel tracks is about one meter (40 inches). Where the receding tracks bend to the left, a circular pattern resulted from Spirit turning in place at a soil target informally named 'Stapledon' after William Olaf Stapledon, a British philosopher and science-fiction author who lived from 1886 to 1950. Scientists on the rover team suspected that the soil in that area might have a high concentration of silica, resembling a high-silica soil patch discovered east of Home Plate in 2007. Bright material visible in the track furthest to the right was examined with Spirit's alpha partical X-ray spectrometer and found, indeed, to be rich in silica. The team laid plans to drive Spirit from this Sol 1802 location back up onto Home Plate, then southward for the rover's summer field season. This view is presented as a cylindrical projection with geometric seam correction.

Overview Of 100 Sols Of Chemcam Operations At Gale Crater

Science.gov (United States)

Maurice, Sylvestre; Wiens, Roger; MSL Science Team

2013-04-01

The Curiosity rover carries the ChemCam instrument suite, a Laser-Induced Breakdown Spectroscopy (LIBS) instrument that can analyze the chemical composition of geological samples at distances up to 7 meters from the rover, and a high resolution camera for context imaging (RMI). In the first 100 sols after landing, ChemCam performed 343 single point measurements on approximately 50 different rocks or soil areas, for over 12,000 laser shots. Each time at least two RMI images are acquired before and after the laser shots to visualize the area of investigation and the geological context. LIBS lines are identified using primarily a martian dedicated database; to date, ChemCam has detected unambiguously major elements (Si, Al, Fe, Mg, Ca, Na, K, O), minor/trace elements of interest (Li, Cr, Mn, Rb, Sr, Ba, Ti, S, C, H). These observations allow a qualitative/quantitative assessment of the presence of dust (first few shots), the sample surface composition and chemical heterogeneity with depth. Several techniques have been developed to analyze ChemCam's data: (1) Univariate analysis refers to peak height studies of well-chosen LIBS lines and a training dataset to build calibration curves. Peak ratios K/Si, Na/Si, Al/Si, Fe+Mg/Si, or Mg/Mg+Fe have been calculated from the onboard calibration targets. The technique also applies to minor and trace elements which yield low intensity emission lines, such as Lin, Rb, H, C. (2) Multivariate methods give better results in terms of elemental composition, since they examine simultaneously and statistically several peaks of the same elements. A Partial Least Squares (PLS) regression algorithm is used for rapid major-element abundance determination. (3) Composition trends, clusters and end-members can also be identified using component analysis methods. Independent Component Analysis (ICA) identifies components that are directly related to Chemical elements: Al, Ca, Fe, H, K, Mg, Na, O, Si, Ti, but also mixture like a "soil" component

Core-SOL modelling of neon seeded JET discharges with the ITER-like wall

Energy Technology Data Exchange (ETDEWEB)

Telesca, G. [Department of Applied Physics, Ghent University (Belgium); EUROfusion Consortium, JET, Culham Science Centre, Abingdon (United Kingdom); Ivanova-Stanik, I.; Zagoerski, R.; Czarnecka, A. [Institute of Plasma Physics and Laser Microfusion, Warsaw (Poland); EUROfusion Consortium, JET, Culham Science Centre, Abingdon (United Kingdom); Brezinsek, S.; Huber, A.; Wiesen, S. [Forschungszentrum Juelich GmbH, Institut fuer Klima- und Energieforschung-Plasmaphysik, Juelich (Germany); EUROfusion Consortium, JET, Culham Science Centre, Abingdon (United Kingdom); Drewelow, P. [Max-Planck-Institut fuer Plasmaphysik, Greifswald (Germany); EUROfusion Consortium, JET, Culham Science Centre, Abingdon (United Kingdom); Giroud, C. [CCFE Culham, Abingdon (United Kingdom); EUROfusion Consortium, JET, Culham Science Centre, Abingdon (United Kingdom); Collaboration: JET EFDA contributors

2016-08-15

Five ELMy H-mode Ne seeded JET pulses have been simulated with the self-consistent core-SOL model COREDIV. In this five pulse series only the Ne seeding rate was changed shot by shot, allowing a thorough study of the effect of Ne seeding on the total radiated power and of its distribution between core and SOL tobe made. The increase in the simulations of the Ne seeding rate level above that achieved in experiments shows saturation of the total radiated power at a relatively low radiated-heating power ratio (f{sub rad} = 0.60) and a further increase of the ratio of SOL to core radiation, in agreement with the reduction of W release at high Ne seeding level. In spite of the uncertainties caused by the simplified SOL model of COREDIV (neutral model, absence of ELMs and slab model for the SOL), the increase of the perpendicular transport in the SOL with increasing Ne seeding rate, which allows to reproduce numerically the experimental distribution core-SOL of the radiated power, appears to be of general applicability. (copyright 2016 The Authors. Contributions to Plasma Physics published by Wiley-VCH Verlag GmbH and Co. KGaA Weinheim. This)

The SOL-2/Neto auxiliary protein modulates the function of AMPA-subtype ionotropic glutamate receptors.

Science.gov (United States)

Wang, Rui; Mellem, Jerry E; Jensen, Michael; Brockie, Penelope J; Walker, Craig S; Hoerndli, Frédéric J; Hauth, Linda; Madsen, David M; Maricq, Andres V

2012-09-06

The neurotransmitter glutamate mediates excitatory synaptic transmission by gating ionotropic glutamate receptors (iGluRs). AMPA receptors (AMPARs), a subtype of iGluR, are strongly implicated in synaptic plasticity, learning, and memory. We previously discovered two classes of AMPAR auxiliary proteins in C. elegans that modify receptor kinetics and thus change synaptic transmission. Here, we have identified another auxiliary protein, SOL-2, a CUB-domain protein that associates with both the related auxiliary subunit SOL-1 and with the GLR-1 AMPAR. In sol-2 mutants, behaviors dependent on glutamatergic transmission are disrupted, GLR-1-mediated currents are diminished, and GLR-1 desensitization and pharmacology are modified. Remarkably, a secreted variant of SOL-1 delivered in trans can rescue sol-1 mutants, and this rescue depends on in cis expression of SOL-2. Finally, we demonstrate that SOL-1 and SOL-2 have an ongoing role in the adult nervous system to control AMPAR-mediated currents. Copyright © 2012 Elsevier Inc. All rights reserved.

Synthesis by sol-gel and characterization of catalysts Ag/Al{sub 2}O{sub 3}- CeO{sub 2} for the elimination of nitric oxide; Sintesis por sol-gel y caracterizacion de catalizadores Ag/Al{sub 2}O{sub 3}- CeO{sub 2} para la eliminacion del oxido nitrico

Energy Technology Data Exchange (ETDEWEB)

Zayas R, M.L

2005-07-01

The environmental pollution is one from the big problems to solve at the present time, because the quality of the alive beings life is affected. For such reason, more clean and economic technologies are required, that it conduces to develop new catalytic alternatives to diminish the nitrogen oxides that due to its chemical processes in the environment contribute considerably in the air pollution. The main objective of the present work, is the preparation and characterization of catalytic materials with base of silver supported in simple and mixed aluminium oxides (Al{sub 2}O{sub 3}) and Cerium oxide (CeO{sub 2}), and its catalytic evaluation that through of the reduction of nitric oxide (NO) using hydrogen (H{sub 2}) as reducer agent. It was synthesized alumina (Al{sub 2}O{sub 3}) and Cerium oxide (CeO{sub 2}) and mixed oxides (Al{sub 2}O{sub 3}- CeO{sub 2}), by the sol-gel method and the cerium oxide (CeO{sub 2}) by precipitation of the cerium nitrate (III) hexa hydrated. The oxides were stabilized thermally at 900 C by 5 hr. The catalysts were prepared by impregnation using silver nitrate (AgNO{sub 3}), the nominal concentration of Ag was of 5% in weight. The catalysts were reduced at 400 C by 2 hr, in hydrogen flow of 60 cc/min. The characterization of the catalytic materials was carried out through different techniques as: nitrogen adsorption to determine the surface area BET, scanning electron microscopy (SEM) to observe the final morphology of the catalysts, X-ray diffraction (XRD) to identify the crystalline phases of the catalytic materials, Infrared spectroscopy (DRIFT) to know the structural characterization of the catalysts, reduction to programmed temperature (TPR) to evidence the interaction metal-support. The catalytic properties of the catalysts were evaluated in the model reaction NO + H{sub 2}, to determine the activity and selectivity. The results indicate that the preparation technique, the precursors and the thermal treatments that underwent

Mechanical compatibility of sol-gel annealing with titanium for orthopaedic prostheses.

Science.gov (United States)

Greer, Andrew I M; Lim, Teoh S; Brydone, Alistair S; Gadegaard, Nikolaj

2016-01-01

Sol-gel processing is an attractive method for large-scale surface coating due to its facile and inexpensive preparation, even with the inclusion of precision nanotopographies. These are desirable traits for metal orthopaedic prostheses where ceramic coatings are known to be osteoinductive and the effects may be amplified through nanotexturing. However there are a few concerns associated with the application of sol-gel technology to orthopaedics. Primarily, the annealing stage required to transform the sol-gel into a ceramic may compromise the physical integrity of the underlying metal. Secondly, loose particles on medical implants can be carcinogenic and cause inflammation so the coating needs to be strongly bonded to the implant. These concerns are addressed in this paper. Titanium, the dominant material for orthopaedics at present, is examined before and after sol-gel processing for changes in hardness and flexural modulus. Wear resistance, bending and pull tests are also performed to evaluate the ceramic coating. The findings suggest that sol-gel coatings will be compatible with titanium implants for an optimum temperature of 500 °C.

Characterization of the allergen Sol gem 2 from the fire ant venom, Solenopsis geminata

Directory of Open Access Journals (Sweden)

S Sukprasert

2012-01-01

Full Text Available Sol i 2 is a potent allergen in Solenopsis invicta venom, and most humans exhibit reactivity to it. The Sol gem 2 allergen found in the venom of the Thai tropical fire ant Solenopsis geminata was analysed in the present study. The protein was present in higher amounts than other proteins, as determined by SDS-PAGE, and presumably has allergenic properties similar to those of Sol i 2. Sol gem 2 molecular weight is 28 and 15 kDa, respectively, under non-reducing and reducing conditions, indicating that its native form is a dimer. LC-MS/MS analysis confirmed its similarity to Sol i 2. The mono/dimeric form of Sol gem 2 was determined to be relevant by proteomic approach and immunoblotting. An anti-Sol gem 2 antibody was produced in mice, with a titer greater than 1:800 according to the Western blotting analysis. The Sol gem 2-neutralising activity of this antibody was determined in crickets. The paralytic dose 50 (PD50 of crude S. geminata venom was elevated from 0.18 mg/g of body weight to more than 0.90 mg/g of body weight after preincubation with antibody at a ratio of 1:1. These results suggest that Sol gem 2 plays an important role in mediating the effects of the piperidine derivatives in the venom.

Opportunity's Surroundings on Sol 1798 (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. This view is presented as a polar projection with geometric seam correction. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

Opportunity's Surroundings on Sol 1798 (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. This view is presented as a vertical projection with geometric seam correction. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

Structure of hybrid organic-inorganic sols for the preparation of hydrothermally stable membranes

Energy Technology Data Exchange (ETDEWEB)

Castricum, H.L.; Sah, A; Blank, D.H.A.; Ten Elshof, J.E. [Inorganic Materials Science, MESA Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Geenevasen, J.A.J. [Van ' t Hoff Institute for Molecular Sciences, University of Amsterdam, Nieuwe Achtergracht 166, 1018 WV Amsterdam (Netherlands); Kreiter, R.; Vente, J.F. [ECN Energy Efficiency in the Industry, Petten (Netherlands)

2008-06-15

A procedure for the preparation of hybrid sols for the synthesis of organic-inorganic microporous materials and thin film membranes is reported. We describe silane reactivity and sol structure for acid-catalysed colloidal sols from mixtures of either tetraethylorthosilicate (TEOS) and methyltriethoxysilane (MTES), or bis(triethoxysilyl)ethane (BTESE) and MTES. Early-stage hydrolysis and condensation rates of the individual silane precursors were followed with 29Si liquid NMR and structural characteristics of more developed sols were studied with Dynamic Light Scattering. Condensation was found to proceed at more or less similar rates for the different precursors. Homogeneously mixed hybrid colloids can therefore be formed from precursor mixtures. The conditions of preparation under which clear sols with low viscosity could be formed from BTESE/MTES were determined. These sols were synthesised at moderate water/silane and acid/silane ratios and could be applied for the coating of defect-free microporous membranes for molecular separations under hydrothermal conditions.

One-step sol-gel imprint lithography for guided-mode resonance structures.

Science.gov (United States)

Huang, Yin; Liu, Longju; Johnson, Michael; C Hillier, Andrew; Lu, Meng

2016-03-04

Guided-mode resonance (GMR) structures consisting of sub-wavelength periodic gratings are capable of producing narrow-linewidth optical resonances. This paper describes a sol-gel-based imprint lithography method for the fabrication of submicron 1D and 2D GMR structures. This method utilizes a patterned polydimethylsiloxane (PDMS) mold to fabricate the grating coupler and waveguide for a GMR device using a sol-gel thin film in a single step. An organic-inorganic hybrid sol-gel film was selected as the imprint material because of its relatively high refractive index. The optical responses of several sol-gel GMR devices were characterized, and the experimental results were in good agreement with the results of electromagnetic simulations. The influence of processing parameters was investigated in order to determine how finely the spectral response and resonant wavelength of the GMR devices could be tuned. As an example potential application, refractometric sensing experiments were performed using a 1D sol-gel device. The results demonstrated a refractive index sensitivity of 50 nm/refractive index unit. This one-step fabrication process offers a simple, rapid, and low-cost means of fabricating GMR structures. We anticipate that this method can be valuable in the development of various GMR-based devices as it can readily enable the fabrication of complex shapes and allow the doping of optically active materials into sol-gel thin film.

Sol-Gel Production; Proceedings of the First International Conference on Application and Commercialization of Sol-Gel Processing Held in Saarbruecken, Germany on 24-25 May 1993

National Research Council Canada - National Science Library

Schmidt, Helmut

1998-01-01

...; Sol-Gel Coatings on Large Glass Substrates for Multilayer Interference Systems; A SiO2-ZrO2 Gel Film doped with Organic Pigments Made by the Sol-Gel Method for Contrast Enhancement of Color Picture Tubes...

Impurity enrichment and radiative enhancement using induced SOL flow in DIII-D

International Nuclear Information System (INIS)

Wade, M.R.; West, W.P.; Wood, R.D.

1998-07-01

Experiments on DIII-D have demonstrated the efficacy of using induced scrap-off-layer (SOL) flow to preferentially enrich impurities in the divertor plasma. This SOL floe is produced through simultaneous deuterium gas injection at the midplane and divertor exhaust. Using this SOL flow, an improvement in enrichment (defined as the ratio of impurity fraction in the divertor to that in the plasma core) has been observed for all impurities in trace-level experiments (i.e., impurity level is non-perturbative), with the degree of improvement increasing with impurity atomic number. In the case of argon, exhaust gas enrichment using modest SOL flow is as high as 17. Using this induced SOL flow technique and argon injection, radiative plasmas have been produced that combine high radiation losses (P rad /P input > 70%), low core fuel dilution (Z eff E > 1.0 τ E,ITER93H )

Sobre nubes y relojes: aproximación al problema de la racionalidad y libertad del hombre* /About clouds and clocks: approach to the problem of rationality and human freedom

Directory of Open Access Journals (Sweden)

Diego A. Restrepo-Ochoa

2013-08-01

Full Text Available La presente reseña tiene como propósito discutir el texto “Sobre Nubes y Relojes” de Karl Popper, en el cual el autor expone sus planteamientos en torno al problema del determinismo y el indeterminismo. En primer lugar, se presenta la discusión sobre el determinismo y el indeterminismo a partir de tres categorías de análisis: lo ontológico, lo metodológico y lo ético; seguidamente se analiza la propuesta evolucionista de Popper con relación al problema del determinismo y, finalmente, se plantean algunas consecuencias epistemológicas y éticas del determinismo en el campo de la salud This review discusses the text “On clouds and Clocks” by Karl Popper, in which the author presents his views on the issue of determinism and indeterminism. First, a discussion on determinism and indeterminism is presented from three analysis categories: ontological, methodological and ethical. Then, Popper's evolutionist approach regarding the issue of determinism is analyzed. Finally, some of the epistemological and ethical consequences of determinism on the field of health are presented.

Laboratory Testing of Silica Sol Grout in Coal Measure Mudstones

Directory of Open Access Journals (Sweden)

Dongjiang Pan

2016-11-01

Full Text Available The effectiveness of silica sol grout on mudstones is reported in this paper. Using X-ray diffraction (XRD, the study investigates how the silica sol grout modifies mudstone mineralogy. Micropore sizes and mechanical properties of the mudstone before and after grouting with four different materials were determined with a surface area/porosity analyser and by uniaxial compression. Tests show that, after grouting, up to 50% of the mesopore volumes can be filled with grout, the dominant pore diameter decreases from 100 nm to 10 nm, and the sealing capacity is increased. Uniaxial compression tests of silica sol grouted samples shows that their elastic modulus is 21%–38% and their uniaxial compressive strength is 16%–54% of the non-grouted samples. Peak strain, however, is greater by 150%–270%. After grouting, the sample failure mode changes from brittle to ductile. This paper provides an experimental test of anti-seepage and strengthening properties of silica sol.

A utilização de materiais obtidos pelo processo de sol-gel na construção de biossensores The utilization of materials obtained by the sol-gel process in biosensors construction

Directory of Open Access Journals (Sweden)

Antonio A. S. Alfaya

2002-09-01

Full Text Available The use of sol-gel materials to develop new biosensors has received great attention due to its characteristics and versatility of sol-gel process. An overview is presented of the state-of-the-art of electrochemical biosensors employing sol-gel materials. Low-temperature, porous sol-gel ceramics represent a new class for the immobilization of biomolecules. The rational design of sol-gel sensing materials, based on the judicious choice of the starting alkoxide, encapsulated reagents, and preparation conditions, allows tailoring of material properties in a wide range, and offers great potential for the development of electrochemical biosensors.

Especificidades sobre processo de luto frente ao suicídio = Specificities about the grieving process forward to suicide = Especificidades sobre el proceso de duelo hacia adelante al suicidio

Directory of Open Access Journals (Sweden)

Fukumitsu, Karina Okajima

2016-01-01

Full Text Available O suicídio de um ente querido pode desencadear nas pessoas diversas reações. No presente artigo apresentam-se as especificidades para diferenciar o processo de luto após o suicídio dos demais lutos, causados por outros tipos de morte. O artigo tem o objetivo de refletir sobre o processo de luto pelo suicídio por meio da compreensão do luto de nove filhos de pessoas que consumaram o suicídio. Foram extraídas 14 unidades de significados a partir do método fenomenológico e compreendidas pela perspectiva da abordagem da Gestalt-terapia. Os depoimentos dos colaboradores, apontam que, ao enfrentar a morte, o filho pode experienciar o sofrimento com sentimentos de culpa, raiva, sensações de desamparo, abandono, rejeição, solidão, além da fragmentação de tudo o que era conhecido

Ultraviolet Sensing by Al-doped ZnO Thin Films

International Nuclear Information System (INIS)

Rashid, A.R.A.; Menon, P.S.; Shaari, S.

2011-01-01

We report the fabrication and characterization of an ultraviolet photoconductive sensing by using Al-doped ZnO films. Undoped ZnO, 1 at.% and 2 at% of Al were prepared on quartz glass by sol gel method with annealing temperature of 500 degree Celsius for 1 hour. The presence of spherical shaped nanoparticles were detected for undoped ZnO by using FESEM. The absorption edge shifted to a lower wavelength by doping with Al and excitonic peak can be observed. The band gap values increased by adding Al. I-V curves reveal an improvement in electrical properties when the samples are illuminated by ultraviolet (UV) light with a wavelength of 365 nm. At 1 at.% of Al, the film have a larger increment in photocurrent response when illuminated with UV light compared to undoped ZnO and 2 at.% Al. The thin films have a longer recovery time than response time. (author)

The Shadow of a Gnomon Along a Year: Routine Observations and Teaching of Apparent Motion of the Sun and the Four Seasons. (Spanish Title: La Sombra de un Gnomon lo Largo de un Año: Observaciones de Rutina y la Enseñanza del Movimiento Aparente del Sol y Las Cuatro Estaciones.) A Sombra de um Gnômon ao Longo de um Ano: Observações Rotineiras e o Ensino do Movimento Aparente do Sol E das Quatro Estações

Science.gov (United States)

Trogello, Anderson Giovani; Danhoni Neves, Marcos Cesar; de Carvalho Rutz da Silva, Sani

2013-12-01

Many misconceptions are recognized among the various groups of students, especially in the elementary school. Among them, the apparent motion of the Sun, in spite of its daily occurrence, is subject to varied interpretations. Thus, the observation and recording of the motion of the stars in the celestial vault is a necessary task for astronomy education. The work presented here proposes the presentation of the results of observations of the apparent movement of the sun by marking the shadow of a vertical gnomon by the students in a class of sixth graders of elementary rural school of Paraná. The project itself was conducted in four stages, on dates near the March equinox, the June solstice, the September equinox and the December solstice. In addition, lectures were developed in the classroom. Such methods sought to build concepts around the apparent movement of the Sun and the alternation of the seasons. Given the results of the activities, an evaluation was applied and the data demonstrated a desired student learning such as: the recognition of the cardinal points, the description of the apparent solar motion and the occurrence of the seasons and their alternation from astronomical observations at naked eye. Muchos conceptos aternativos son conocidos entre los distintos grupos de alumnos, sobre todo en la educación básica. Entre ellos, el movimiento aparente del Sol, por más cotidiano que sea, se presta a interpretaciones variadas. Por lo tanto, observar y registrar el movimiento de las estrellas en la bóveda celeste se torna una tarea necesaria para la educación en astronomía. El trabajo que aquí se presenta propone la presentación de los resultados de la observación del movimiento aparente del sol a través de la marcación de la sombra del gnomon vertical a cargo de los estudiantes en una división de sexto grado de de la escuela primaria rural de Paraná. El proyecto en sí se llevó a cabo en cuatro etapas, en fechas cercanas al equinoccio de marzo

HIDROGENACIÓN SELECTIVA EN FASE LIQUIDA DE 1-HEPTINO SOBRE Ni/Al2O3. EFECTO DE LA TEMPERATURA DE REACCIÓN

Directory of Open Access Journals (Sweden)

María J. Maccarrone

2011-01-01

Full Text Available En este trabajo fue evaluado el efecto de la temperatura de reacción en la hidrogenación selectiva de 1-heptino a 1-hepteno usando un catalizador de níquel soportado sobre γ -alúmina. Fueron estudiadas diferentes temperaturas operacionales (273, 303 y 323 K, obteniéndose mayor conversión total del reactivo a la mayor temperatura, con una selectividad próxima al 90%. El catalizador de níquel preparado puede considerarse como una alternativa más económica a nivel industrial frente a los ya conocidos catalizadores de paladio, no sólo debido al bajo costo del metal sino también debido a su bajo contenido metálico (3,6% en masa. El catalizador fue caracterizado por Difracción de Rayos X, Reducción a Temperatura Programada y Espectroscopía Fotoelectrónica de Rayos X. Estas indicaron la presencia de óxido de níquel a nivel másico con fuertes interacciones con el soporte y la existencia de especies electro-deficientes de níquel a nivel superficial quienes serían las especies activas durante la hidrogenación del alquino terminal.

CATALIZADOR ESTRUCTURADO DE Pt/Al2O3 SOBRE UNA ESPUMA DE ACERO INOXIDABLE (AISI 314 PARA LA OXIDACIÓN DE CO

Directory of Open Access Journals (Sweden)

Juan P. Bortolozzi

2011-01-01

Full Text Available Se obtuvo un catalizador estructurado por recubrimiento de Pt/Al2O3 sobre las paredes de una espuma de acero inoxidable AISI 314. Para estabilizar térmicamente e incrementar la rugosidad de la superficie de la espuma original se realizó un tratamiento a 900°C por 2 h. El soporte, Al2O3, y el metal activo, Pt, se incorporaron por inmersión. Las técnicas de caracterización aplicadas, XRD, LRS y SEM-EDX, permiten concluir que el tratamiento térmico previo indujo la formación de óxido de cromo y de las espinelas Mn1+xCr2-xO4-x y FeCr2O4 como fases principales en las paredes del sustrato. El espesor de la capa formada es cercano a 1 μm y los cristales producidos tienen forma octaédrica. El cubrimiento de alúmina presentó en general una apariencia homogénea, sin interacción con los óxidos formados durante el tratamiento. El Pt se distribuyó de manera uniforme, resultando un catalizador muy activo para la reacción test elegida: oxidación de monóxido de carbono.

Estado del arte del conocimiento sobre perifiton en Colombia

Directory of Open Access Journals (Sweden)

Yimmy Montoya Moreno

2013-12-01

Full Text Available El perifiton es un componente de las comunidades bióticas acuáticas, su estudio es importante tanto desde la perspectiva ecológica, para comprender el funcionamiento de los ecosistemas acuáticos, como desde el punto de vista ambiental, pues su composición y estructura pueden servir como indicadores de la calidad del agua y de procesos que como la contaminación puedan estar afectando a los ecosistemas. La investigación sobre el perifiton es compleja; la definición misma de perifiton aún genera controversias. Sumado a esto, la variedad de metodologías para su estudio integral, la diversidad de arquitecturas de la matriz perifítica, la gran diversidad de ecosistemas y la ausencia de escuelas taxonómicas en el país, contribuyen a que sean pocos los trabajos que se publican sobre el tema, lo que incrementa el valor e importancia de los estudios reseñados en esta revisión. El objetivo de este artículo es dar a conocer el estado del arte en la investigación sobre el perifiton en Colombia, mediante el análisis de diferentes líneas de investigación que se han desarrollado y su grado de avance. Con este fin, se examinaron 84 trabajos a los que los autores tuvieron acceso. La mayoría de investigaciones consultadas en este trabajo (90%, corresponden al estudio de ficoperifiton, el 10% restante incluyó ambos componentes del perifiton y se encontró una dedicada exclusivamente al zooperifiton. Sólo el 10,5% de las investigaciones (8 trabajos se han dedicado al estudio taxonómico detallado, el resto de publicaciones se orientan al estudio de la estructura y dinámica de la comunidad perifítica.

Sobre una carta de condolencia al consejo y al pueblo de Cotieo

Directory of Open Access Journals (Sweden)

María C. GINER SORIA

2010-02-01

Full Text Available Or. XXXII de Elio Arístides es un discurso dedicado a honrar la memoria de un hombre ilustre desaparecido *. Si las dudas en torno a la existencia real del atleta Melancomas tuvieran fundamento 2, Alejandro de Cotieo, que vivió hasta mediado el siglo II d. C. 3 habría inspirado el primer epitafio conservado en honor de un individuo, ya que cronológicamente es anterior al epicedio por Eteoneo, compuesto, también por Elio Arístides, en 161. Pero no es el discurso funeral de Arístides dedicado a su antiguo maestro Alejandro de Cotieo lo que quisiéramos examinar ahora, en sí mismo, sino el soporte apistolar en que se apoya, encuadramiento que Arístides estimó adecuado influido, en parte, al menos, por el hecho de que proyectaba enviarlo desde Esmirna a Cotieo. Al conocer la noticia de la muerte de su maestro, al que parece haber estimado sinceramente, sintió el impulso de honrarlo con el elogio de sus cualidades profesionales y humanas. Pero con dificultad podría haberse desplazado Arístides oportunamente para asistir a las exequias de su maestro. Cotieo se halla a más de trescientos kilómetros de Esmisna y las noticias tardarían en llegar. Por eso, aunque las relaciones con los familiares de Alejandro eran antiguas y Arístides no carecía de renombre, sería obligado encomendar el elogio del difunto en las honras fúnebres a alguien más cercano. Por otra parte, el precario estado de la salud de Elio Arístides le hubiera impedido, muy posiblemente, desplazarse a tan gran distancia, en el caso de que hubieran solicitado de él la composición del discurso, con este sólo fin. Durante años Arístides no había pronunciado personalmente todos los discursos que escribía, los enviaba y eran leídos públicamente por alguien, en su nombre. Y los hacía llegar, más o menos privadamente, a importantes destinatarios, como confirma él mismo en el comienzo de or XIX: «En anteriores ocasiones, emperadores excelsos, os envié por escrito

Effect of sol concentration on the structural, morphological, optical and photoluminescence properties of zirconia thin films

International Nuclear Information System (INIS)

Joy, K.; Maneeshya, L.V.; Thomas, Jijimon K.; Thomas, P.V.

2012-01-01

ZrO 2 thin films were deposited on quartz substrates from 10 wt.%, 20 wt.% and 40 wt.% solutions of Zirconium-n-butoxide in isopropanol by sol–gel dip-coating technique. Higher concentrated sols of 20 wt.% and 40 wt.% exhibited faster gelation, where as 10 wt.% sol remained stable for two months and films synthesized from this sol remained transparent and continuous even for 12 coatings. Ellipsometric study revealed that refractive index of the films increased with increase in sol concentration which is ascribed to the decrease in porosity. X-ray diffraction study showed that a tailoring of grain size from 7.9 to 39.2 nm is possible with increase in sol concentration. Atomic force microscopy studies showed a change in growth mode from vertical to lateral mode with increase in sol concentration. The film surface revealed positive skewness and high kurtosis values which make them favorable for tribological applications. The average optical transmittance in the visible region is highest (greater than 90%) for the film deposited from 10 wt.% sol. The optical band gap decreased from 5.74 to 5.62 eV with increase in the sol concentration. Photoluminescence (PL) spectra of the films exhibit an increase in the emission intensity with increase in sol concentration which substantiates better crystalline quality of the film deposited from 40 wt.% sol and increase in oxygen vacancies. The “Red shift” of the PL spectra with increase in sol concentration originates from the increase in the grain size with sol concentration which makes it suitable for generation of solid state lighting in light emitting diode. - Highlights: ► ZrO 2 thin films were deposited on quartz substrates by sol-gel method. ► Control of grain size with sol concentration. ► Microstructure studies showed a change in growth mode from vertical to lateral mode. ► The optical band gap decreased with increase in grain size and sol concentration. ► Dependence of photoluminescence on particle size

Sobre-educación en el mercado laboral colombiano

Directory of Open Access Journals (Sweden)

Jhon James Mora

2008-12-01

Full Text Available Este artículo analiza la sobre-educación en Colombia con datos de individuos y empresas compilados por el Servicio Nacional de Aprendizaje de Colombia en 2006, encuentra que la probabilidad de estar sobre-educado es del 14% y que depende de la movilidad entre áreas de desempeño, la experiencia, el género, el tamaño de la empresa y el nivel de educación. Los trabajadores sobre-educados ganan un 2% menos que los trabajadores correctamente educados, conforme al patrón internacional. Los resultados también muestran que la probabilidad de que los profesionales permanezcan en la misma área de desempeño aumenta con la experiencia, que cuanto mayor es la sobre-educación menor es la probabilidad de permanecer en dicha área y que los trabajadores con postgrado tienen menor probabilidad de permanecer en su área de desempeño.

Sobre una Rodoficea parasita de Gelidiaceas

OpenAIRE

Seoane Camba, Juan Antonio

1982-01-01

En este trabajo se hace un estudio de una Rodofícea parásita, encontrada sobre Gelidium cantabricum Seoane-Camba y Gelidium sesquipedale (Clemente) Thuret. Por sus características generales atribuímos esta planta al género Gelidiocolax. descrito por Gardner en 1927 para un parásito de Gelidium pulchrum Gardner de las costas americanas del Pacífico...

Waveguide fabrication in UV-photocurable sol-gel materials: Influence of the photoinitiating system

International Nuclear Information System (INIS)

Versace, D.L.; Oubaha, M.; Copperwhite, R.; Croutxe-Barghorn, C.; MacCraith, B.D.

2008-01-01

In this paper we identify and explain the different chemical interactions involved between a sol-gel matrix and photoinitiators used in the fabrication of optical waveguides. A well-established sol-gel matrix composed of 3-methacryloxypropyltrimethoxysilane, zirconium n-propoxide and methacrylic acid was developed, and two different photoinitiators (Irgacure (registered) 819 and 1800) were added to the host matrix. Optical microscopy was used to characterise the structure of the waveguides as a function of the photoinitiator nature and concentration, and aging of the hybrid sol-gel material. It is clearly demonstrated that the width of the waveguides is strongly influenced by the sol aging. Furthermore, it is shown that degradation of photoinitiators occurs during the sol-gel process. Oxidation of the phosphonyl groups by the zirconium complex accounts for this results

Himno a Barranquilla

Directory of Open Access Journals (Sweden)

Amira de la Rosa

2013-05-01

Full Text Available Barranquilla, prócera e inmortal Ceñida de agua y madurada al sol Savia joven del árbol nacional.   Del jubiloso porvenir crisol Ilusión de Caribe blanco-azul De Colombia tendida en el umbral Da su voz y su músculo al progreso Barranquilla, prócera e inmortal.   Barrancas de San Nicolás con el Magdalena detrás.   Coronada de firme amanecer  te conduce en su espalda el porvenir: las sirenas de fábrica y taller son rumor arterial de tu existir.   Barranquilla sabe cantar  y sobre el yunque martillar.   Tajamares de Bocas de Ceniza Cuchillada del río sobre el mar al Caribe central colombianiza  tu robusta aptitud de navegar.   Amira de la Rosa Poetisa y dramaturga colombiana (1903-1974 (Fundadora del colegio Gabriela Mistral de Barranquilla, 1926

Declaración de la Ciudad de México sobre las políticas culturales

OpenAIRE

Revista Chasqui

2015-01-01

Al reunirse en México la Conferencia Mundial sobre las Políticas Culturales la comunidad internacional ha decidido contribuir efectivamente al acercamiento entre los pueblos y a la mejor comprensión entre los hombres.

Aprendiendo sobre el poder y la ciudadanía en un mundo virtual

Directory of Open Access Journals (Sweden)

David Buckingham

2013-03-01

Full Text Available En este trabajo se presenta una investigación orientada a analizar cómo se desarrollan las relaciones de poder dentro de un mundo virtual dirigido al público infantil y adolescente (Habbo Hotel. Se pretendía llegar a comprender cómo estaba la compañía propietaria de ese espacio moderando, y por lo tanto ejerciendo su poder, a través de los diferentes actores encargados de tomar decisiones sobre el comportamiento de los usuarios dentro del mundo virtual. Al mismo tiempo, se profundizó en el tipo de lecciones que aprenden los usuarios sobre el ejercicio de la ciudadanía, derivadas de las normas de comportamiento impuestas por la compañía. Para comprender qué estaban aprendiendo los menores sobre el ejercicio del poder y sobre el prototipo de ciudadano modelo dentro del mundo virtual, analizamos los sistemas de reglas que regulan aquello que pueden o no hacer los usuarios y procedimos al análisis del contenido de espacios en los que los usuarios hablaban sobre los motivos por los que la compañía los había expulsado de «Habbo Hotel». Los resultados de este trabajo ponen de manifiesto que la aplicación del sistema de reglas por parte de la compañía hace que la experiencia dentro del mundo virtual no sea siempre lúdica, democrática, creativa, participativa o plenamente satisfactoria. Esto pone en entredicho algunos de los principales argumentos esgrimidos por diferentes autores en defensa de estos nuevos medios de comunicación.

Time for a Change; Spirit's View on Sol 1843 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11973 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11973 NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this stereo, full-circle view of the rover's surroundings during the 1,843rd Martian day, or sol, of Spirit's surface mission (March 10, 2009). South is in the middle. North is at both ends. This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The rover had driven 36 centimeters downhill earlier on Sol 1854, but had not been able to get free of ruts in soft material that had become an obstacle to getting around the northeastern corner of the low plateau called 'Home Plate.' The Sol 1854 drive, following two others in the preceding four sols that also achieved little progress in the soft ground, prompted the rover team to switch to a plan of getting around Home Plate counterclockwise, instead of clockwise. The drive direction in subsequent sols was westward past the northern edge of Home Plate. This view is presented as a cylindrical-perspective projection with geometric seam correction.

Porous alumina scaffold produced by sol-gel combined polymeric sponge method

Science.gov (United States)

Hasmaliza, M.; Fazliah, M. N.; Shafinaz, R. J.

2012-09-01

Sol gel is a novel method used to produce high purity alumina with nanometric scale. In this study, three-dimensional porous alumina scaffold was produced using sol-gel polymeric sponge method. Briefly, sol gel alumina was prepared by evaporation and polymeric sponge cut to designated sizes were immersed in the sol gel followed by sintering at 1250 and 1550°C. In order to study the cell interaction, the porous alumina scaffold was sterilized using autoclave prior to Human Mesenchymal Stem Cells (HMSCs) seeding on the scaffold and the cell proliferation was assessed by alamarBlue® assay. SEM results showed that during the 21 day period, HMSCs were able to attach on the scaffold surface and the interconnecting pores while maintaining its proliferation. These findings suggested the potential use of the porous alumina produced as a scaffold for implantation procedure.

Properties of Zn O/Cr thin films prepared by Sol-Gel; Propiedades de peliculas delgadas ZnO/Cr preparadas por Sol-Gel

Energy Technology Data Exchange (ETDEWEB)

Tirado G, S.; Olvera A, R., E-mail: tirado@esfm.ipn.mx [IPN, Escuela Superior de Fisica y Matematicas, Edificio 9, Unidad Profesional A. L. M., San Pedro Zacatenco, 07788 Mexico D. F. (Mexico)

2014-08-15

Zn O films and those superficially modified with chromium were deposited on substrates of soda-lime glass, using the Sol-Gel process and the repeated immersion method. Starting from dehydrated zinc acetate was prepared a solution to 0.6 M to ambient temperature in 2-methoxyethanol and monoethanolamine (Mea) stirring magnetically. The Sol was prepared with an aging to seven days and was used to grow a films group with thickness to eight immersions. These same films were superficially modified with several depositions of a chromium nitrate Sol dissolved in ethanol to low concentration. The Zn O films were structurally characterized by X-ray diffraction, its chemical composition by energy dispersive X-ray spectroscopy and its morphology by scanning electron microscopy and atomic force microscopy, as well as their optical properties by UV-vis. Of the obtained results are proposed possible applications. (author)

Salt-assisted and salt-suppressed sol-gel transitions of methylcellulose in water.

Science.gov (United States)

Xu, Y; Wang, C; Tam, K C; Li, L

2004-02-03

The effects of various salts on the sol-gel transition of aqueous methylcellulose (MC) solutions have been studied systematically by means of a micro differential scanning calorimeter. It was found that the heating process was endothermic while the cooling process was exothermic for both MC solutions with and without salts. The addition of salts did not change the patterns of gelation and degelation of MC. However, the salts could shift the sol-gel transition and the gel-sol transition to lower or higher temperatures from a pure MC solution, depending on the salt type. These opposite effects were termed the salt-assisted and salt-suppressed sol-gel transitions. Either the salt-assisted transition or the salt-suppressed sol-gel transition was a function of salt concentration. In addition, each salt was found to have its own concentration limit for producing a stable aqueous solution of MC at a given concentration of MC, which was related to the anionic charge density of the salt. Cations were proved to have weaker effects than anions. The "salt-out strength", defined as the salt effect per mole of anion, was obtained for each anion studied. The thermodynamic mechanisms involved in the salt-assisted and salt-suppressed sol-gel transitions are discussed.

Análisis cualitativo sobre la movilidad al trabajo en bicicleta: Comparación de dos ciudades con diferentes infraestructuras y políticas ciclistas

OpenAIRE

Lois, David; López-Sáez, Mercedes; Rondinella, Gianni

2016-01-01

Este trabajo presenta los resultados de un estudio cualitativo sobre la valoración de la bicicleta como modo de transporte para viajar al lugar de trabajo. Se llevaron a cabo veintiuna entrevistas semi-estructuradas, en dos ciudades españolas, Vitoria-Gasteiz y Madrid, con diferentes infraestructuras ciclistas y porcentajes de uso. La categorización e interpretación de los resultados se realizó bajo el marco de la teoría de la acción planificada (Ajzen, 1991). Los resultados indican que la bi...

Improved photoluminescence property of CTAB assisted polyaniline-AlZnO nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Mitra, Mousumi; Banerjee, Dipali, E-mail: dipalibanerjeebesu@gmail.com [Department of Physics, Indian Institute of Engineering Science and Technology, Shibpur, Howrah (India); Kargupta, Kajari [Department of Chemical Engineering, Jadavpur University, Kolkata (India); Ganguly, Saibal [Chemical Engineering department, Universiti Teknology Petronas, Tronoh (Malaysia)

2015-06-24

Polyaniline-Al doped ZnO ((PANI-AlZnO:: 70:30) nanocomposite was prepared via in situ chemical oxidative polymerization, while the hexagonal powder of AlZnO was synthesized via sol-gel technique, using Hexadecyltrimethylammonium bromide (CTAB) as a capping agent. The prepared nanocomposite was characterized by High resolution transmission electron microscopy (HRTEM), EDAX, X-ray diffraction (XRD) and Fourier transforms infrared (FTIR) spectra. The optical property of the nanomaterials is examined by photoluminescence (PL) spectra analysis. The XRD pattern confirms the formation of Al doped ZnO as well as PANI. The HRTEM images of the composite showed the formation of hexagonal AlZnO embedded in polyaniline matrix. EDAX spectrum shows the compositional analysis of the nanocomposite. FTIR spectra confirm the formation of nanocomposite of PANI and hexagonal AlZnO. The PL intensity of the nanocomposite is improved as compared to pure AlZnO.

Efecto del estrés asociado al destete sobre variables Clínico-Patológicas  y la integridad de la mucosa gástrica en Potros Pura Sangre de Carrera

OpenAIRE

Chacón, Tony C.; Zerpa, Héctor; Cova, Francisco J.; Campos, Gerardo J

2006-01-01

El destete en los caballos Pura Sangre de carreras (PSC), se realiza regularmente a los seis meses de edad. Esta medida de manejo puede conllevar al desarrollo de estrés post-destete, con todos los potenciales efectos deletéreos que éste puede originar. El objetivo de este trabajo fue investigar el efecto de dos tipos de destete sobre variables clínico-patológicas y hallazgos gastroscópicos, como indicadores de estrés en potros PSC. Se seleccionaron al azar doce potros de seis meses de edad, ...

Creencias sobre series de ficción televisiva: el caso de Velvet

OpenAIRE

Cristina Etayo Pérez

2015-01-01

Las series de televisión son un género de ficción muy atractivo tanto para los espectadores como para las cadenas que las emiten. Dados sus altos costes de producción, deben atraer al público desde el primer momento. Hay estudios sobre los factores que determinan el éxito de una película de cine pero se ha realizado escasa investigación sobre estos factores en series de televisión. En este trabajo se analizan las creencias de los espectadores sobre un conjunto de factores objetivos de la seri...

Entre negación y reconocimiento. Estudios sobre “homosexualidad” en Colombia

Directory of Open Access Journals (Sweden)

José Fernando Serrano A.

1997-04-01

Full Text Available A Ebel Botero, pionero de los estudios sobre homosexualidad en Colombia¿Qué se ha escrito en Colombia sobre la “homosexualidad”? ¿Existen estudios desde las ciencias sociales y humanas sobre las personas “homosexuales” en el país? Con este par de preguntas el autor presenta un recorrido inicial por algunos textos de autores colombianos al respecto y señala la necesidad de abordar la construcción de conocimiento especializado que ahonde en la comprensión de las diversas formas en que se expresan las sexualidades.

Bio-indicateurs de la fertilité des sols et la perception paysanne à l ...

African Journals Online (AJOL)

SARAH

30 mai 2015 ... d'identifier des bio-indicateurs des sols fertiles et des sols dégradés selon la perception paysanne et des paramètres ..... effet, une augmentation du stock hydrique du sol à ... Fonctionnement et gestion des écosystèmes.

Transport barrier fluctuations governed by SOL turbulence spreading

International Nuclear Information System (INIS)

Ghendrih, Ph.; Sarazin, Y.; Ciraolo, G.; Darmet, G.; Garbet, X.; Grangirard, V.; Tamain, P.; Benkadda, S.; Beyer, P.

2007-01-01

Turbulence spreading, namely turbulent transport extending into a stable region is reported both for the flat density profiles in the far SOL and into a modeled H-mode barrier. It is shown that due to turbulence penetration, the pedestal width fluctuates and that its effective width is a factor 2 smaller than the linear predicted width. Turbulence overshooting throughout the pedestal leads to a non-vanishing turbulent transport within the barrier and provides a coupling of core and SOL turbulence despite the transport barrier

Novel hybrid sol-gel coatings for corrosion protection of AZ31B magnesium alloy

International Nuclear Information System (INIS)

Lamaka, S.V.; Montemor, M.F.; Galio, A.F.; Zheludkevich, M.L.; Trindade, C.; Dick, L.F.; Ferreira, M.G.S.

2008-01-01

This work aims to develop and study new anticorrosion films for AZ31B magnesium alloy based on the sol-gel coating approach. Hybrid organic-inorganic sols were synthesized by copolymerization of epoxy-siloxane and titanium or zirconium alkoxides. Tris(trimethylsilyl) phosphate was also used as additive to confer additional corrosion protection to magnesium-based alloy. A sol-gel coating, about 5-μm thick, shows good adhesion to the metal substrate and prevents corrosion attack in 0.005 M NaCl solution for 2 weeks. The sol-gel coating system doped with tris(trimethylsilyl)-phosphate revealed improved corrosion protection of the magnesium alloy due to formation of hydrolytically stable Mg-O-P chemical bonds. The structure and the thickness of the sol-gel film were characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The corrosion behaviour of AZ31B substrates pre-treated with the sol-gel derived hybrid coatings was tested by electrochemical impedance spectroscopy (EIS). The chemical composition of the silylphosphate-containing sol-gel film at different depths was investigated by X-ray photoelectron spectroscopy (XPS) with depth profiling

Formulation and evaluation of antimicrobial activity of Morus alba sol-gel against periodontal pathogens

Directory of Open Access Journals (Sweden)

Shilpa Gunjal

2015-01-01

Full Text Available Background: Periodontitis has a multifactorial etiology, with primary etiologic agents being pathogenic bacteria that reside in the subgingival area. Recent advances in the field of alternative medicine introduced various herbal products for the treatment of periodontitis. Aim: To assess and compare the antimicrobial activity of Morus alba sol-gel with chlorhexidine sol-gel against ATCC standard strains of Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis, and Tannerella forsythia. Materials and Methods: Crude extract of Morus alba leaves was prepared by Soxhlet method by using ethanol as a solvent. Phytochemical screening of the crude extract of M. alba was performed to check the various chemical constituents. M. alba sol-gel and chlorhexidine sol-gel were formulated using Pluronic f127 and Pluronic f108 and compared for their antimicrobial activity. The minimum inhibitory concentration of both the gels was performed using agar well diffusion technique. Results: The minimum inhibitory concentration of M. alba sol-gel and chlorhexidine sol-gel against A. actinomycetemcomitans is 19 and 17 mm, T. forsythia is 12 and 21 mm, and P. gingivalis is 16 and 18 mm, respectively. Conclusion: Both M. alba and chlorhexidine sol-gel exhibited potent antimicrobial activity against periodontal pathogens.

Influence of Ce(III/Ce(IV - supplements on the Characteristics of Humidity Sensors with TiO2 Films Prepared via a Sol-gel Method

Directory of Open Access Journals (Sweden)

Kozhukharov, S.

2013-04-01

Full Text Available Humidity sensors have been prepared via a sol-gel method to deposit TiO2 films with additions of Ce-compounds on alumina substrates, with interdigitated silver palladium electrodes. Observations by scanning electron microscopy (SEM were performed in order to determine the surface morphology of the respective layers. Structural and compositional characterization was done by X-ray diffraction analysis (XRD, and energy dispersive X-ray spectroscopy (EDX for investigation of the relation between the film structures and the parameters of the respective sensors. The influence of Ce-compounds on the electrical characteristics of the samples as humidity sensing elements has been evaluated by an impedance analyzer.Los sensores de humedad han sido desarrollados mediante el método sol-gel para depositar películas superficiales basadas en TiO2 con adiciones de compuestos de cerio sobre sustratos de corindón y electrodos de aleación de plata y paladio. Se han realizado observaciones mediante el Microscopio Electrónico de Barrido (MEB para determinar la morfología superficial de las capas respectivas. Las caracterizaciones de la estructura y composición han sido realizadas mediante Difracción de Rayos X (DRX y espectroscopía de dispersión energética de rayos X (EDERX, con el fin de investigar la relación entre la estructura de las capas y los parámetros de los sensores respectivos. La influencia de los compuestos de cerio sobre las características eléctricas de los sensores de humedad obtenidos se ha evaluado mediante el análisis de impedancia eléctrica.

Sol-gel antireflective coating on plastics

Science.gov (United States)

Ashley, Carol S.; Reed, Scott T.

1990-01-01

An antireflection film made from a reliquified sol-gel hydrolyzation, condensation polymeric reaction product of a silicon, alkoxides and/or metal alkoxides, or mixtures thereof. The film is particularly useful for coating plastics.

LO POLÍTICO Y LAS POLÍTICAS DE LA DELINCUENCIA JUVENIL. Una reflexión sobre el caso de jóvenes vinculados al Sistema de Responsabilidad Penal Adolescente. Bogotá-Colombia

Directory of Open Access Journals (Sweden)

Ana Guadalupe Cienfuegos

2015-01-01

Full Text Available El presente artículo ofrece una reflexión en torno a lo político, entendido como dimensión constitutiva de las sociedades humanas, en el fenómeno social de la delincuencia juvenil. La reflexión se enmarca en un estudio realizado por la autora en torno a los sentidos y significados del delito en jóvenes vinculados al Sistema de Responsabilidad Penal Adolescente (SRPA en Bogotá - Colombia y el análisis conceptual realizado en el marco de una investigación sobre Justicia Restaurativa y Sistema de Responsabilidad Penal Adolescente. Se analizan los resultados de talleres investigativos y entrevistas en profundidad realizadas con jóvenes vinculados al SRPA identificando lo que se constituye para ellos como «político», los sentidos y significados sobre las dimensiones y los escenarios de sus vidas asociados con lo político y las recomendaciones frente a las políticas de prevención y atención de la delincuencia juvenil.

Patterned transparent zinc oxide films produced by sol-gel embossing

Energy Technology Data Exchange (ETDEWEB)

Rao, J.; Koh, L.H.K.; Crean, G.M. [Tyndall National Institute, Lee Maltings, Prospect Row, Cork (Ireland); Department of Microelectronic Engineering, University College Cork, Cork (Ireland); O' Brien, S. [Tyndall National Institute, Lee Maltings, Prospect Row, Cork (Ireland); Winfield, R.J.

2008-08-15

A low cost zinc oxide embossing technique is reported as a method of fabricating structures relevant to a variety of applications. A zinc based sol-gel material was prepared from zinc acetate[Zn(C{sub 2}H{sub 3}O{sub 2}){sub 2}], monoethanolamine[H{sub 2}NC{sub 2}H{sub 4}OH] and isopropanol. The sol-gel was cast into a polydimethylsiloxane (PDMS) mould a track design, placed in contact with the substrate and dried under vacuum at 70 C for 3 hours. The formed track pattern was further densified to provide a stable conductor film that retained the embossed shape. An optimum Zn sol-gel content of 0.6 M was identified. The embossed films had a transparency of greater than 83% in the visible region. The optical bandgap energy was evaluated to be 3.306 eV. The influence of ZnO sol-gel film synthesis and embossing parameters on the microstructure, morphology and optical transparency of fabricated structures is described. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Amoeba-like self-oscillating polymeric fluids with autonomous sol-gel transition.

Science.gov (United States)

Onoda, Michika; Ueki, Takeshi; Tamate, Ryota; Shibayama, Mitsuhiro; Yoshida, Ryo

2017-07-13

In the field of polymer science, many kinds of polymeric material systems that show a sol-gel transition have been created. However, most systems are unidirectional stimuli-responsive systems that require physical signals such as a change in temperature. Here, we report on the design of a block copolymer solution that undergoes autonomous and periodic sol-gel transition under constant conditions without any on-off switching through external stimuli. The amplitude of this self-oscillation of the viscosity is about 2,000 mPa s. We also demonstrate an intermittent forward motion of a droplet of the polymer solution synchronized with the autonomous sol-gel transition. This polymer solution bears the potential to become the base for a type of slime-like soft robot that can transform its shape kaleidoscopically and move autonomously, which is associated with the living amoeba that moves forward by a repeated sol-gel transition.

El impacto de la estructura de las redes sociales sobre el acceso de los individuos al mercado laboral

Directory of Open Access Journals (Sweden)

García-Valdecasas, José Ignacio

2014-08-01

Full Text Available This work attempts to analyse the effect of social networks structure on the access to the labour market for individuals through the diffusion of information which takes place in such networks (an aspect of social capital. For that purpose, it combines agent-based modelling and social network analysis in order to carry out virtual experiments with artificial networks. The results show that not only the type of structure (small world, free scale networks, random networks and regular networks, but also certain structural properties such as the density of network, the index of globalization in links or the degree of inequality in the distribution of links affect deeply on the opportunities of agents in order to achieve employment.Este trabajo pretende analizar el efecto de la estructura de las redes sociales sobre el acceso de los individuos al mercado laboral a través de la difusión de la información que tiene lugar en dichas redes (un aspecto del capital social. Para realizar tal análisis, se ha llevado a cabo una serie de experimentos virtuales con redes artificiales, utilizando para ello la simulación basada en agentes y el análisis de redes sociales. Los resultados muestran que no solo el tipo de estructura (mundos pequeños, redes de libre escala, redes aleatorias y redes regulares, sino también ciertas propiedades estructurales como la densidad de red, el índice de globalización de vínculos o el grado de desigualdad en la distribución de vínculos influyen considerablemente sobre las oportunidades de los agentes de conseguir empleo.

La cooperaci??n hispano-portuguesa en materia de agua a la luz del Protocolo sobre el agua y la salud al Convenio de 1992 sobre la protecci??n y uso de los cursos de agua transfronterizos y los lagos internacionales de 1999

OpenAIRE

Escudero Espinosa, Juan Francisco

2009-01-01

P. 237-245. A lo largo de la historia, Espa??a y Portugal han suscrito diferentes acuerdos de cooperaci??n de car??cter sectorial relativos al r??gimen de los r??os comunes. El marco convencional existente fue perfeccionado de forma global mediante el Convenio sobre cooperaci??n para la protecci??n y el aprovechamiento sostenible de las aguas de las cuencas hidrogr??ficas hispano-portuguesas (Convenio de Albufeira), celebrado en Albufeira el 30 de noviembre de 1998. A nivel europeo, fue...

The influence of sol on the behavior of melting and nonisothermal crystallization kinetic of radiation cross-linking HDPE

International Nuclear Information System (INIS)

Deng Pengyang; Xie Hongfeng; Deng Mingxiao; Zhong Xiaoguang

2000-01-01

By using DSC, the behavior of second melting and nonisothermal crystallization of pure gel pure sol and sol-gel blend of radiation crosslinking HDPE was studied. The authors found that, because of the existence of sol, there is notable difference between pure gel and pure sol or sol-gel blend. Under the same dose, the melting point and crystallization temperature of pure sol and sol-gel blend are higher than that of pure gel. At the same time, the authors also found that the Avrami exponent of original PE, pure sol and sol-gel blend is the similar to each other and different to that of pure gel, which means that the procedure of nucleation and growth of these samples is the same and also different to that of pure gel

Opportunity's Surroundings After Sol 1820 Drive

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). South is at the center; north at both ends. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

Uranium Dioxide Powder Flow ability Improvement Using Sol-Gel

International Nuclear Information System (INIS)

Juanda, D.; Sambodo Daru, G.

1998-01-01

The improvement of flow ability characteristics of uranium dioxide powder has been done using sol-gel process. To anticipate a pellet mass production with uniform pellet dimension, the uranium dioxide powder must be have a spherical form. Uranium dioxide spherical powder has been diluted in acid transformed into sol colloidal solution. To obtain uranium dioxide spherical form, the uranium sol-colloidal solution has been dropped in a hot paraffin ( at the temperature of 90 0 C) to form gelatinous colloid and then dried at 800 0 C, and sintered at the temperature of 1700 0 C. The flow ability of spherical uranium dioxide powder has been examined by using Flowmeter Hall (ASTM. B. 213-46T). The measurement result reveals that the spherical uranium dioxide powder has a flow ability twice than that of unprocessed uranium dioxide powder

Efecto de la incorporación de Hf en el crecimiento de los recubrimientos de Al sobre aceros ferrítico-martensíticos mediante CVD-FBR

Directory of Open Access Journals (Sweden)

Francisco Javier Bolívar

2010-01-01

Full Text Available En las últimas décadas, ha habido un marcado interés por aumentar la temperatura y la presión de vapor en las plantas de generación de energía con el propósito de disminuir el consumo de combustibles. Así, se conseguiría reducir las emisiones de contaminantes tales como CO2 SO2 y NOx. Para lograr estas mejoras, se requiere por un lado desarrollar nuevosaceros ferríticos-martensíticos con contenidos de Cr entre 9-12% y por otro lado, mediante la ingeniería de superficies, mejorar la resistencia a la oxidación de los ya existentes. En el presente trabajo se obtuvieron recubrimientos de Al y de Al-Hf y evaluó el efecto de la adición del Hf al lecho sobre el crecimiento de los recubrimientos de Al. Previamente a la obtención de los recubrimientos, se realizó un estudio termodinámico mediante el programa Themocalc y, de acuerdo a los resultados obtenidos, se depositaron las capas de Al y Al-Hf a tres temperaturas diferentes en el rango de 500 a 600 °C. Los recubrimientos fueron caracterizados mediante DRX y MEB/EDAX. De acuerdo con los resultados obtenidos se determinó que para ambos casos las capas estaban fundamentalmente formadas por los compuestos intermetálicos Fe2Al5 y FeAl3.

Profiles and fluctuations in edge and SOL turbulence

DEFF Research Database (Denmark)

Naulin, Volker; Xu, G.; Vianello, N.

2012-01-01

propagating structures and parallel transport sets up the observed profiles and how intermittency influences edge conditions. The filamentary blob structures also transport and generate currents in the SOL, which can be investigated by means of local magnetic diagnostics. Finally, the ratio of ion to electron...... temperature in the SOL is an important measure for the influence of finite larmor radius effects on the propagation properties of blobs. Numerical investigations indicate that these effects can lead to an increased self confinement and radial reach of these structures. © 2012 WILEY-VCH Verlag GmbH & Co. KGa...

Rationale and Design of the Echocardiographic Study of Hispanics/Latinos (ECHO-SOL).

Science.gov (United States)

Rodriguez, Carlos J; Dharod, Ajay; Allison, Matthew A; Shah, Sanjiv J; Hurwitz, Barry; Bangdiwala, Shrikant I; Gonzalez, Franklyn; Kitzman, Dalane; Gillam, Linda; Spevack, Daniel; Dadhania, Rupal; Langdon, Sarah; Kaplan, Robert

2015-01-01

Information regarding the prevalence and determinants of cardiac structure and function (systolic and diastolic) among the various Hispanic background groups in the United States is limited. The Echocardiographic Study of Latinos (ECHO-SOL) ancillary study recruited 1,824 participants through a stratified-sampling process representative of the population-based Hispanic Communities Health Study - Study of Latinos (HCHS-SOL) across four sites (Bronx, NY; Chicago, Ill; San Diego, Calif; Miami, Fla). The HCHS-SOL baseline cohort did not include an echo exam. ECHO-SOL added the echocardiographic assessment of cardiac structure and function to an array of existing HCHS-SOL baseline clinical, psychosocial, and socioeconomic data and provides sufficient statistical power for comparisons among the Hispanic subgroups. Standard two-dimensional (2D) echocardiography protocol, including M-mode, spectral, color and tissue Doppler study was performed. The main objectives were to: 1) characterize cardiac structure and function and its determinants among Hispanics and Hispanic subgroups; and 2) determine the contributions of specific psychosocial factors (acculturation and familismo) to cardiac structure and function among Hispanics. We describe the design, methods and rationale of currently the largest and most comprehensive study of cardiac structure and function exclusively among US Hispanics. ECHO-SOL aims to enhance our understanding of Hispanic cardiovascular health as well as help untangle the relative importance of Hispanic subgroup heterogeneity and sociocultural factors on cardiac structure and function.

Preparation and characterization of conductive and transparent ruthenium dioxide sol-gel films.

Science.gov (United States)

Allhusen, John S; Conboy, John C

2013-11-27

RuO2 conductive thin films were synthesized using the sol-gel method and deposited onto transparent insulating substrates. The optical transmission, film thickness, surface morphology and composition, resistivity, and spectroelectrochemical performance have been characterized. The optical transmission values of these films ranged from 70 to 89% in the visible region and from 56 to 88% in the infrared region. Resistivity values of the RuO2 sol-gel films varied from 1.02 × 10(-3) to 1.13 Ω cm and are highly dependent on the initial solution concentration of RuO2 in the sol-gel. The RuO2 sol-gel films were used as electrodes for the electrochemical oxidation and reduction of ferrocenemethanol. The electrochemical behavior of our novel RuO2 sol-gel films was compared to that of a standard platinum disk electrode and showed no appreciable differences in the half-wave potential (E1/2). The mechanical and chemical stability of the coatings was tested by physical abrasion and exposure to highly acidic, oxidizing Piranha solution. Repeated exposure to these extreme conditions did not result in any appreciable decline in electrochemical performance. Finally, the use of the novel RuO2 sol-gel conductive and transparent films was demonstrated in a spectroelectrochemistry experiment in which the oxidation and reduction of ferrocenemethanol was monitored via UV-vis spectroscopy as the applied potential was cycled.

Understanding the SOL flow in L-mode plasma on divertor tokamaks, and its influence on the plasma transport

International Nuclear Information System (INIS)

Asakura, Nobuyuki

2007-01-01

Significant progress has been made in understanding the driving mechanisms in SOL mass transport along the magnetic field lines (SOL flow). SOL flow measurements by Mach probes and impurity plume have been performed in L-mode plasma at various poloidal locations in divertor tokamaks. All results showed common SOL flow patterns: subsonic flow with parallel Mach number (M parallel ) of 0.2-1 was generated from the Low-Field-Side (LFS) SOL to the High-Field-Side (HFS) divertor for the ion ∇B drift towards the divertor. The SOL flow pattern was formed mainly by LFS-enhanced asymmetry in diffusion and by classical drifts. In addition, divertor detachment and/or intense puffing-and-pump enhanced the HFS SOL flow. Most codes have incorporated drift effects, and asymmetric diffusion was modelled to simulate the fast SOL flow. Influences of the fast SOL flow on the impurity flow in the SOL, shielding from core plasma, and deposition profile, were directly observed in experiments

UN MODELO SOBRE CÓMO LAS ESTRATEGIAS MOTIVACIONALES RELACIONADAS CON EL COMPONENTE DE AFECTIVIDAD INCIDEN SOBRE LAS ESTRATEGIAS COGNITIVAS Y METACOGNITIVAS

Directory of Open Access Journals (Sweden)

José Manuel Suárez Riveiro

2013-01-01

Full Text Available El principal propósito de este trabajo fue el de proponer un modelo sobre cómo las estrategias motivacionales relacionadas al componente de afectividad inciden sobre la utilización de las estrategias cognitivas y metacognitivas. La muestra utilizada fue de 500 estudiantes de Secundaria. Se asumió que el efecto de las estrategias motivacionales sobre las estrategias cognitivas estaría mediado por el uso de las estrategias metacognitivas. Para estudiar estas estrategias y su relación se realizaron análisis descriptivos y se elaboró un diagrama de senderos. Los resultados mostraron que la estrategia motivacional más utilizada es la de autorrefuerzo y que se establecen relaciones significativas desde algunas estrategias motivacionales, pero no desde todas, con las estrategias cognitivas aunque únicamente la estrategia de autorrefuerzo establece relaciones significativas con la autorregulación metacognitiva.

Optical Studies on Sol-Gel Derived Lead Chloride Crystals

OpenAIRE

Rejeena, I; Lillibai, B; Nithyaja, B; Nampoori, P.N V; Radhakrishnan, P

2013-01-01

Optical characterization of lead chloride crystals prepared by sol-gel method is reported. The relevant sol-gel technique is used for the preparation of PbCl2 samples with five different types. In this paper, we report the absorption and fluorescence behaviour of pure, UV& IR irradiated and electric & magnetic field applied lead chloride crystal samples in solution phase at two different concentrations. Optical bandgap and emission studies of these crystals are also done.

Efecto del número de aplicaciones de cloprostenol sobre la regresión de cuerpos lúteos, el retorno al celo y la ovulación, después de un tratamiento superovulatorio en donantes de embriones bovinos

OpenAIRE

Cabra, C.; Garzón, J. V.; Tribulo, A.; Mapletoft, R.; Jiménez, C.; Bo, G.

2011-01-01

El objetivo del presente trabajo fue evaluar la respuesta de la aplicación doble o triple de prostaglandina sobre la regresión de CL, ovulación y retorno al celo después de un tratamiento superovulatorio en vacas donantes de embriones. Para este experimento se tomaron 44 vacas asignadas al azar a dos grupos de tratamiento. Al primero (n = 23; CLO 0 & 7) se le aplicó una dosis de 500 μg de cloprostenol los días 0 (denominado día de la colecta) y 7; al segundo grupo (n = 21; ...

Effect of different sol concentrations on the properties of nanocrystalline ZnO thin films grown on FTO substrates by sol-gel spin-coating

International Nuclear Information System (INIS)

Kim, Ikhyun; Kim, Younggyu; Nam, Giwoong; Kim, Dongwan; Park, Minju; Kim, Haeun; Lee, Wookbin; Leem, Jaeyoung; Kim, Jongsu; Kim, Jin Soo

2014-01-01

Nanocrystalline ZnO thin films grown on fluorine-doped tinoxide (FTO) substrates were fabricated using the spin-coating method. The structural and the optical properties of the ZnO thin films prepared using different sol concentrations were investigated by using field-emission scanning electron microscopy (FE-SEM), X-ray diffractometry (XRD), photoluminescence (PL) measurements, and ultraviolet-visible (UV-vis) spectrometry. The surface morphology of the ZnO thin films, as observed in the SEM images, exhibited a mountain-chain structure. XRD results indicated that the thin films were preferentially orientated along the direction of the c-axis and that the grain size of the ZnO thin films increased with increasing sol concentration. The PL spectra showed a strong ultraviolet emission peak at 3.22 eV and a broad orange emission peak at 2.0 eV. The intensities of deep-level emission (DLE) gradually increased with increasing sol concentration from 0.4 to 1.0 M. The transmittance spectra of the ZnO thin films showed that the ZnO thin films were transparent (∼85%) in the visible region and exhibited sharp absorption edges at 375 nm. Thus, The Urbach energy of ZnO thin films decreased with increasing sol concentration.

Algunas consideraciones sobre la estrategia de mercadotecnia en los negocios internacionales

OpenAIRE

Ernesto Raúl González Ramírez

2016-01-01

El presente artículo aborda algunas consideraciones sobre la estrategia de mercadotecnia en el contexto de los negocios internacionales. La primera parte está dirigida a describir las particularidades de las estrategias específicas de mercadotecnia (producto, precio, comunicación y distribución) en el área internacional. La segunda parte, trata sobre la importancia de tener presente el nivel de orientación al mercado o aplicación del concepto de mercadotecnia en este contexto.

Miradas francesas sobre la Guerra Civil

Directory of Open Access Journals (Sweden)

Jean-Marc DELAUNAY

2015-03-01

Full Text Available Como muestra el asunto hoy vigente —pero relativamente discreto— de la venta del edificio que abrigó el antiguo taller parisino donde Picasso hizo su Guernica (1937, la Guerra Civil española sigue siendo en Francia una referencia mayor de la historia contempóranea. Al ritmo de las conmemoraciones decenales de su estallido (1996/2006, se ha desarrollado una verdadera marea memorial nutrida tanto por la apertura de archivos escritos y audiovisuales como por la desinhibición de los nietos de exiliados condicionados durante tanto tiempo por la historia de la derrota de sus padres y abuelos. Animan el debate las tribulaciones de la vida política española actual, entre neofranquismo, republicanismo y nacionalismos centralistas y/o regionales. Por haber sido la unica vía de salida, Francia —metropolis y África del norte— se vio más involucrada que cualquier otro país al recibir la aplastante mayoría de los exiliados. Aunque los verdaderos especialistas en dicha guerra son poco numerosos, todo un mundillo se ha otorgado el derecho y la capacidad de escribir sobre ella como descendientes de exiliados o activistas políticos, sobre todo en el sur de Francia. Todos los medios se ven afectados: desde la literatura estrictamente histórica al internet. De las obras eruditas, de vulgarización —también para la juventud— a las memorias arrancadas al olvido; de las actas de los coloquios a los tebeos; de los álbumes fotográficos a los documentales (siempre pro republicanos. Al tiempo toda la producción histórica generalista o militar junta a los partidarios de una visión anticomunista, neutralista o manifestamente pro franquista. La Guerra Civil española, que había encontrado una Francia dividida, la reencuentra de nuevo como tal a pesar de todos los intentos de mediación científica.

Spirit Near 'Stapledon' on Sol 1802 (Vertical)

Science.gov (United States)

2009-01-01

NASA Mars Exploration Rover Spirit used its navigation camera for the images assembled into this full-circle view of the rover's surroundings during the 1,802nd Martian day, or sol, (January 26, 2009) of Spirit's mission on the surface of Mars. North is at the top. This view is presented as a vertical projection with geometric seam correction. Spirit had driven down off the low plateau called 'Home Plate' on Sol 1782 (January 6, 2009) after spending 12 months on a north-facing slope on the northern edge of Home Plate. The position on the slope (at about the 9-o'clock position in this view) tilted Spirit's solar panels toward the sun, enabling the rover to generate enough electricity to survive its third Martian winter. Tracks at about the 11-o'clock position of this panorama can be seen leading back to that 'Winter Haven 3' site from the Sol 1802 position about 10 meters (33 feet) away. For scale, the distance between the parallel wheel tracks is about one meter (40 inches). Where the receding tracks bend to the left, a circular pattern resulted from Spirit turning in place at a soil target informally named 'Stapledon' after William Olaf Stapledon, a British philosopher and science-fiction author who lived from 1886 to 1950. Scientists on the rover team suspected that the soil in that area might have a high concentration of silica, resembling a high-silica soil patch discovered east of Home Plate in 2007. Bright material visible in the track furthest to the right was examined with Spirit's alpha partical X-ray spectrometer and found, indeed, to be rich in silica. The team laid plans to drive Spirit from this Sol 1802 location back up onto Home Plate, then southward for the rover's summer field season.

Spirit Near 'Stapledon' on Sol 1802 (Polar)

Science.gov (United States)

2009-01-01

NASA Mars Exploration Rover Spirit used its navigation camera for the images assembled into this full-circle view of the rover's surroundings during the 1,802nd Martian day, or sol, (January 26, 2009) of Spirit's mission on the surface of Mars. North is at the top. This view is presented as a polar projection with geometric seam correction. Spirit had driven down off the low plateau called 'Home Plate' on Sol 1782 (January 6, 2009) after spending 12 months on a north-facing slope on the northern edge of Home Plate. The position on the slope (at about the 9-o'clock position in this view) tilted Spirit's solar panels toward the sun, enabling the rover to generate enough electricity to survive its third Martian winter. Tracks at about the 11-o'clock position of this panorama can be seen leading back to that 'Winter Haven 3' site from the Sol 1802 position about 10 meters (33 feet) away. For scale, the distance between the parallel wheel tracks is about one meter (40 inches). Where the receding tracks bend to the left, a circular pattern resulted from Spirit turning in place at a soil target informally named 'Stapledon' after William Olaf Stapledon, a British philosopher and science-fiction author who lived from 1886 to 1950. Scientists on the rover team suspected that the soil in that area might have a high concentration of silica, resembling a high-silica soil patch discovered east of Home Plate in 2007. Bright material visible in the track furthest to the right was examined with Spirit's alpha partical X-ray spectrometer and found, indeed, to be rich in silica. The team laid plans to drive Spirit from this Sol 1802 location back up onto Home Plate, then southward for the rover's summer field season.

Synthesis of yttrium silicate luminescent materials by sol-gel method

International Nuclear Information System (INIS)

Arkhipov, D.V.; Vasina, O.Yu.; Popovich, N.V.; Galaktionov, S.S.; Soshchin, N.P.

1996-01-01

Several yttrium-silicate composition with Y 2 O 3 content within 44-56% have been synthesized. it is ascertained that employment of sol-gel technique permits preparation of luminescent materials on yttrium silicate basis, which compare favourably with bath-produced specimens. The influence of phase composition of sol-gel phosphors on basic performance indices: intensity and luminescence spectrum, has been analyzed

Sobre la teoría impura del derecho

Directory of Open Access Journals (Sweden)

Danilo Rojas Betancourt

2006-01-01

Full Text Available La reseña hecha al libro del profesor Diego López, la Teoría impura del derecho, muestra algunos aspectos que debilitan la novedosa e importante tesis allí sostenida sobre la transformación de la teoría jurídica en Latinoamérica. En especial, señala que la particular apreciación de López sobre algunos tópicos kelsenianos deja demasiado expuesta la demostración que respecto de Kelsen proporciona como ejemplo de transformación teórica en Colombia. El reparo central radica en que la construcción hecha por López de lo que se denominaría regla de tanteo de la Teoría Transnacional del Derecho, TTD, toma como base una versión formalizada y no crítica de esta. Al hacerlo, López cae en la misma trampa que pretende mostrar como característica de la transformación local y que, conforme a la lectura estándar de cierta TTD, debe señalarse como incorrecta.

¿Es obligatoria la Declaración sobre Medios?

Directory of Open Access Journals (Sweden)

Leonard R. Sussman

2015-01-01

Full Text Available Siempre propició Ciespal la información sobre el Nuevo Orden Mundial de la Información y abrió las páginas de Chasqui para el debate de las dos tendencias contrapuestas. Ciespal lideró la tesis del Nuevo Orden pero mantuvo la objetividad enla información y el equilibrio en los espacios dados al debate. Así, en su primer número trató sobre el Informe MacBride y en el segundo y tercero sobre la posición de los Estados Unidos. A propósito del retiro de este país del seno de la UNESCO la controversia ha tomado un sesgo nuevo. El presente artículo, desde una posición alineada con la tesis de los Estados Unidos, ofrece ciertas conciliaciones. El lector tiene la palabra.

Functionalizable Sol-Gel Silica Coatings for Corrosion Mitigation

Science.gov (United States)

Gąsiorek, Jolanta; Babiarczuk, Bartosz; Kaleta, Jerzy; Jones, Walis; Krzak, Justyna

2018-01-01

Corrosion is constantly a major problem of the world economy in the field of metal products, metal processing and other areas that utilise metals. Previously used compounds utilizing hexavalent chromium were amongst the most effective materials for corrosion protection but regulations have been recently introduced that forbid their use. Consequently, there is a huge drive by engineers, technologists and scientists from different disciplines focused on searching a new, more effective and environmentally-friendly means of corrosion protection. One novel group of materials with the potential to solve metal protection problems are sol-gel thin films, which are increasingly interesting as mitigation corrosion barriers. These environmentally-friendly and easy-to-obtain coatings have the promise to be an effective alternative to hexavalent chromium compounds using for anti-corrosion industrial coatings. In this review the authors present a range of different solutions for slow down the corrosion processes of metallic substrates by using the oxides and doped oxides obtained by the sol-gel method. Examples of techniques used to the sol-gel coating examinations, in terms of anti-corrosion protection, are also presented. PMID:29373540

Spirit's View Beside 'Home Plate' on Sol 1823

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Spirit used its navigation camera to take the images that have been combined into this 180-degree view of the rover's surroundings during the 1,823rd Martian day, or sol, of Spirit's surface mission (Feb. 17, 2009). The center of the view is toward the south-southwest. The rover had driven 7 meters (23 feet) eastward earlier on Sol 1823, part of maneuvering to get Spirit into a favorable position for climbing onto the low plateau called 'Home Plate.' However, after two driving attempts with negligible progress during the following three sols, the rover team changed its strategy for getting to destinations south of Home Plate. The team decided to drive Spirit at least partway around Home Plate, instead of ascending the northern edge and taking a shorter route across the top of the plateau. Layered rocks forming part of the northern edge of Home Plate can be seen near the center of the image. Rover wheel tracks are visible at the lower edge. This view is presented as a cylindrical projection with geometric seam correction.

Functionalizable Sol-Gel Silica Coatings for Corrosion Mitigation.

Science.gov (United States)

Gąsiorek, Jolanta; Szczurek, Anna; Babiarczuk, Bartosz; Kaleta, Jerzy; Jones, Walis; Krzak, Justyna

2018-01-26

Corrosion is constantly a major problem of the world economy in the field of metal products, metal processing and other areas that utilise metals. Previously used compounds utilizing hexavalent chromium were amongst the most effective materials for corrosion protection but regulations have been recently introduced that forbid their use. Consequently, there is a huge drive by engineers, technologists and scientists from different disciplines focused on searching a new, more effective and environmentally-friendly means of corrosion protection. One novel group of materials with the potential to solve metal protection problems are sol-gel thin films, which are increasingly interesting as mitigation corrosion barriers. These environmentally-friendly and easy-to-obtain coatings have the promise to be an effective alternative to hexavalent chromium compounds using for anti-corrosion industrial coatings. In this review the authors present a range of different solutions for slow down the corrosion processes of metallic substrates by using the oxides and doped oxides obtained by the sol-gel method. Examples of techniques used to the sol-gel coating examinations, in terms of anti-corrosion protection, are also presented.

Humor y excentricidad en Ṭabaqāt al-Šu‘arā’ al-muḥdaṯīn de Ibn al-Mu‘tazz

Directory of Open Access Journals (Sweden)

Garulo, Teresa

2009-12-01

Full Text Available The purpose of this paper is to call attention to this book by Ibn al-Mu‘tazz, sometimes neglected, emphasizing its worth as a literary work and as a source for the study of humour in Arabic literature. Ṭabaqāt al-shu‘arā’ al-muḥdathīn is a very curious repository of biographies of ‘Abbāsid poets, with especial attention to the least known among them, but with personalities that might give occasion to tell a good story about their wit or their folly. So we have, at the same time that we receive information about some very famous poets, a remarkable record full of empathy and humour with tales of madmen, profligate people and rogues and scoundrels boasting of their trades.

Tanto la poesía de Ibn al-Mu‘tazz, como su reflexión teórica sobre el nuevo estilo de poetizar que se inicia con los poetas ‘abbāsíes, han atraído la atención de críticos e investigadores, por la serena armonía de sus versos y la potente visualidad de sus imágenes y metáforas, y, en el caso del Kitāb al-badī‘, por tratarse de la primera obra dedicada a las figuras y tropos que caracterizan la poesía de los poetas postomeyas. Sin embargo, su antología sobre los poetas muḥdaṯūn ha quedado relegada a la posición ancilar de repositorio de nombres de poetas, fundamentalmente menores, de la época ‘abbāsí. En este artículo intento una lectura menos utilitaria de las Ṭabaqāt al-Šu‘arā’ al-muḥdaṯīn para destacar su calidad como obra literaria y, sobre todo, su interés para la historia del humor en la literatura árabe, pues su autor refleja en ella su curiosidad por personajes excéntricos, ridículos o marginales, que sólo se salvan de la condena absoluta por su pasión por la poesía.

Insuficiencia normativa sobre roles y funciones para los miembros de la Fuerza Pública

OpenAIRE

Morales Hernández, Martha Lizett; Ruiz, Jesus A.

2016-01-01

Atendiendo al interés de conocer la manera en que se han manejado en Colombia las políticas sobre Seguridad y Defensa Nacional, respecto de la seguridad jurídica de los miembros de la Fuerza Pública, el presente artículo bajo el método bibliográfico e histórico, plantea en su primera parte, la manera en que los gobiernos elegidos a partir de la Constitución de 1991, concibieron la Seguridad y la Defensa, así como sus políticas sobre este particular; posteriormente, se estudian las normas sobr...

Opportunity's View After Long Drive on Sol 1770 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11791 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11791 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this stereo, full-circle view of the rover's surroundings just after driving 104 meters (341 feet) on the 1,770th Martian day, or sol, of Opportunity's surface mission (January 15, 2009). This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Prior to the Sol 1770 drive, Opportunity had driven less than a meter since Sol 1713 (November 17, 2008), while it used the tools on its robotic arm first to examine a meteorite called 'Santorini' during weeks of restricted communication while the sun was nearly in line between Mars and Earth, then to examine bedrock and soil targets near Santorini. The rover's position after the Sol 1770 drive was about 1.1 kilometer (two-thirds of a mile) south southwest of Victoria Crater. Cumulative odometry was 13.72 kilometers (8.53 miles) since landing in January 2004, including 1.94 kilometers (1.21 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a cylindrical-perspective projection with geometric seam correction.

Avaliação sazonal da produção de borracha e da dinâmica de carboidratos solúveis em plantas de seringueira (Heveabrasiliensis Müll. Arg. cultivadas em Lavras, Minas Gerais

Directory of Open Access Journals (Sweden)

Lima Denis Ubeda de

2002-01-01

Full Text Available O objetivo deste trabalho foi avaliar a produção de látex de seringueira (Heveabrasiliensis e as possíveis alterações no teor de carboidratos em função das variações de fatores climáticos. Foram utilizadas plantas do clone RRIM 600 com 8 anos de idade e no primeiro ano de exploração. As análises dos teores de açúcares solúveis totais e açúcares redutores foram realizadas em duas datas distintas, 29/8/97 (inverno e 23/12/97 (verão, com amostragens em intervalos de 3 horas, em um ciclo de 24 horas de avaliação. A produção de borracha seca foi avaliada em duas sangrias, em cada estação. Os resultados evidenciaram que, além da relação da produção de borracha com a disponibilidade de água, as variações de temperatura entre as estações também tiveram uma importante influência sobre a disponibilidade de carboidratos para a síntese de látex.

Magnetic resonance as a structural probe of a uranium (VI) sol-gel process

International Nuclear Information System (INIS)

King, C.M.; Thompson, M.C.; Buchanan, B.R.; King, R.B.; Garber, A.R.

1989-01-01

NMR investigations on the ORNL process for sol-gel synthesis of microspherical nuclear fuel (UO 2 ), has been useful in sorting out the chemical mechanism in the sol-gel steps. 13 C, 15 N, and 1 H NMR studies on the HMTA gelation agent (Hexamethylene tetramine, C 6 H l2 N 4 ) has revealed near quantitative stability of this adamantane-like compound in the sol-Gel process, contrary to its historical role as an ammonia source for gelation from the worldwide technical literature. 17 0 NMR of uranyl (UO 2 ++ ) hydrolysis fragments produced in colloidal sols has revealed the selective formation of a uranyl trimer, [(UO 2 ) 3 (μ 3 -O)(μ 2 -OH) 3 ] + , induced by basic hydrolysis with the HMTA gelation agent. Spectroscopic results show that trimer condensation occurs during sol-gel processing leading to layered polyanionic hydrous uranium oxides in which HMTAH + is occluded as an ''intercalation'' cation. Subsequent sol-gel processing of microspheres by ammonia washing results in in-situ ion exchange and formation of a layered hydrous ammonium uranate with a proposed structural formula of (NH 4 ) 2 [(UO 2 ) 8 O 4 (OH) 10 ] · 8H 2 0. This compound is the precursor to sintered U0 2 ceramic fuel

Sobre el Contenido de los Marcos Conceptuales Contables

Directory of Open Access Journals (Sweden)

Leila Di Russo de Hauque

2007-12-01

Full Text Available El presente trabajo tiene como objetivo el análisis de los distintos marcos conceptuales vigentes en diferentes sistemas normativos contables. Paralelamente a las revisiones empíricas que dicho trabajo determina, incluye reflexiones a priori sobre el contenido de dichos marcos conceptuales. El trabajo discurre inicialmente sobre el problema de la naturaleza normativa o doctrinaria de sus contenidos tradicionales sin inclinarse definitivamente por una u otra vertiente. Respecto de los elementos que se incluirán en ellos, se justifica la inclusión de las listas de objetivos y requisitos de la información contable para definir el alcance del concepto de informe de uso externo. Además se define a favor de la inclusión, conjuntamente con las respuestas a las pregunas básicas sobre la labor contable, de contenidos ligados al proceso de obtención y de la exposición de la información contable de uso externo.

Hegel sobre Tácito y la libertad teutona

Directory of Open Access Journals (Sweden)

Valerio Rocco Lozano

2015-09-01

Full Text Available Una investigación sobre la presencia (así como sobre la ausencia de Tácito en Hegel es crucial para entender la posición política y filosófica de este pensador, especialmente en la época de Jena. Tras algunas consideraciones sobre el conocimiento hegeliano de la historia y la cultura romanas, se abordará un análisis de su noción de "libertad teutona": Hegel se opone tanto a la neo-romanidad de los revolucionarios franceses como al esencialismo teutómano de los conservadores alemanes (derivado fundamentalmente de un uso fuertemente ideológico de la "Germania" de Tácito, así como a las caducas instituciones imperiales. Esta doble oposición sitúa a Hegel en medio de dos corrientes políticas (e incluso de dos ejércitos en guerra y se lleva a cabo desde una actitud que puede denominarse como “mediación sin nostalgia”

Foldable and Cytocompatible Sol-gel TiO2 Photonics.

Science.gov (United States)

Li, Lan; Zhang, Ping; Wang, Wei-Ming; Lin, Hongtao; Zerdoum, Aidan B; Geiger, Sarah J; Liu, Yangchen; Xiao, Nicholas; Zou, Yi; Ogbuu, Okechukwu; Du, Qingyang; Jia, Xinqiao; Li, Jingjing; Hu, Juejun

2015-09-07

Integrated photonics provides a miniaturized and potentially implantable platform to manipulate and enhance the interactions between light and biological molecules or tissues in in-vitro and in-vivo settings, and is thus being increasingly adopted in a wide cross-section of biomedical applications ranging from disease diagnosis to optogenetic neuromodulation. However, the mechanical rigidity of substrates traditionally used for photonic integration is fundamentally incompatible with soft biological tissues. Cytotoxicity of materials and chemicals used in photonic device processing imposes another constraint towards these biophotonic applications. Here we present thin film TiO2 as a viable material for biocompatible and flexible integrated photonics. Amorphous TiO2 films were deposited using a low temperature (<250 °C) sol-gel process fully compatible with monolithic integration on plastic substrates. High-index-contrast flexible optical waveguides and resonators were fabricated using the sol-gel TiO2 material, and resonator quality factors up to 20,000 were measured. Following a multi-neutral-axis mechanical design, these devices exhibit remarkable mechanical flexibility, and can sustain repeated folding without compromising their optical performance. Finally, we validated the low cytotoxicity of the sol-gel TiO2 devices through in-vitro cell culture tests. These results demonstrate the potential of sol-gel TiO2 as a promising material platform for novel biophotonic devices.

Sol-Gel Precursors for Ceramics from Minerals Simulating Soils from the Moon and Mars

Science.gov (United States)

Sibille, Laurent; Gavira-Gallardo, Jose-Antonio; Hourlier-Bahloul, Djamila

2003-01-01

Recent NASA mission plans for the human exploration of our Solar System has set new priorities for research and development of technologies necessary to enable a long-term human presence on the Moon and Mars. The recovery and processing of metals and oxides from mineral sources on other planets is under study to enable use of ceramics, glasses and metals by explorer outposts. We report some preliminary results on the production of sol-gel precursors for ceramic products using mineral resources available in Martian or Lunar soil. The presence of SiO2, TiO2, and A12O3 in both Martian (44 wt.% SiO2, 1 wt.% TiO2, 7 wt.% Al2O3) and Lunar (48 wt.% SiO2, 1.5 wt.% TiO2, 16 wt.% Al2O3) soils and the recent developments in chemical processes to solubilize silicates using organic reagents and relatively little energy indicate that such an endeavor is possible. In order to eliminate the risks involved in the use of hydrofluoric acid to dissolve silicates, two distinct chemical routes are investigated to obtain soluble silicon oxide precursors from Lunar and Martian simulant soils. Clear sol-gel precursors have been obtained by dissolution of silica from Lunar simulant soil in basic ethylene glycol (C2H4(OH)2) solutions to form silicon glycolates. Thermogravimetric Analysis and X-ray Photoelectron Spectroscopy were used to characterize the elemental composition and structure of the precursor molecules. Further concentration and hydrolysis of the products was performed to obtain gel materials for evaluation as ceramic precursors. In the second set of experiments, we used the same starting materials to synthesize silicate esters in acidified alcohol mixtures. Preliminary results indicate the presence of silicon alkoxides in the product of distillation.

Plumas para el sol: commentarios a un documento sobre cazadores y cotos de caza en el antiguo Perú

Directory of Open Access Journals (Sweden)

1980-01-01

Full Text Available Cet article traite brièvement des activités cynégétiques dans l'ancient Pérou. L'analyse du conflit entre les curacas de Atun Colla et Mañazo nous fait découvrir des fragments importants d'un vaste réseau d'activités liées à la chasse, ses privilèges et ses obligations. La recompilation analytique des chroniques et du document d'Atun Colla élargit notre vision des relations socio-économiques à l'intérieur de l'Etat inca. El presente trabajo es una primera indagación sobre la actividad cinegética en el Antiguo Perú. A través del litigio entre los curacas de Atun Colla y Mañazo se descubre importantes fragmentos de una vasta red de acciones conectadas a la caza y a los privilegios y obligaciones en que esta actividad estaba enmarcada. Los autores han recopilado analíticamente la información de las crónicas, a la que agregan el referido documento de Atun Colla, cuyas evidencias nos amplían el panorama de las relaciones socio-económicas al interior del Estado inca. This article is a first approach to hunting activities in ancient Peru. From the analysis of legal suits between the curacas of Atun Colla and Mañazo, very important fragments of a large network of activities related to hunting and its privileges and obligations. The authors have collated analytically from the chronicles and the Atun Colla document, both of which broaden our understanding of social and economic relationships within the Inca state.

Algunas consideraciones sobre la estrategia de mercadotecnia en los negocios internacionales

Directory of Open Access Journals (Sweden)

Ernesto Raúl González Ramírez

2016-01-01

Full Text Available El presente artículo aborda algunas consideraciones sobre la estrategia de mercadotecnia en el contexto de los negocios internacionales. La primera parte está dirigida a describir las particularidades de las estrategias específicas de mercadotecnia (producto, precio, comunicación y distribución en el área internacional. La segunda parte, trata sobre la importancia de tener presente el nivel de orientación al mercado o aplicación del concepto de mercadotecnia en este contexto.

Sol-Gel Synthesis Of Aluminoborosilicate Powders

Science.gov (United States)

Bull, Jeffrey; Leiser, Daniel; Selvaduray, Guna

1992-01-01

Application of sol-gel process to synthesis of aluminoborosilicate powders shows potential for control of microstructures of materials. Development of materials having enhanced processing characteristics prove advantageous in extending high-temperature endurance of fibrous refractory composite insulation made from ceramic fibers.

Fast-wave power flow along SOL field lines in NSTX and the associated power deposition profile across the SOL in front of the antenna

International Nuclear Information System (INIS)

Perkins, R.J.; Bell, R.E.; Diallo, A.; Gerhardt, S.; Hosea, J.C.; Jaworski, M.A.; LeBlanc, B.P.; Kramer, G.J.; Maingi, R.; Phillips, C.K.; Podestà, M.; Roquemore, L.; Scotti, F.; Ahn, J.-W.; Gray, T.K.; Green, D.L.; McLean, A.; Ryan, P.M.; Jaeger, E.F.; Sabbagh, S.

2013-01-01

Fast-wave heating and current drive efficiencies can be reduced by a number of processes in the vicinity of the antenna and in the scrape-off layer (SOL). On NSTX from around 25% to more than 60% of the high-harmonic fast-wave power can be lost to the SOL regions, and a large part of this lost power flows along SOL magnetic field lines and is deposited in bright spirals on the divertor floor and ceiling. We show that field-line mapping matches the location of heat deposition on the lower divertor, albeit with a portion of the heat outside of the predictions. The field-line mapping can then be used to partially reconstruct the profile of lost fast-wave power at the midplane in front of the antenna, and the losses peak close to the last closed flux surface as well as the antenna. This profile suggests a radial standing-wave pattern formed by fast-wave propagation in the SOL, and this hypothesis will be tested on NSTX-U. RF codes must reproduce these results so that such codes can be used to understand this edge loss and to minimize RF heat deposition and erosion in the divertor region on ITER. (paper)

Laser sintering of doped strontium aluminate via modified sol-gel for use as a ceramic pigment; Sinterizacao a laser do aluminato de estroncio dopado via sol-gel modificado para aplicacao como pigmento ceramico

Energy Technology Data Exchange (ETDEWEB)

Soares, F.M. dos S.; Valerio, M.E.G. [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil)

2017-01-15

Powder of Dy{sup 3+} co-doped SrAl{sub 2}O{sub 4} :Eu{sup 3+} was produced via proteic sol-gel method, a modified sol-gel route which allows the formation of oxides at lower temperatures than other methods. CO{sub 2} laser sintering was used as a method for heat treatment, effective in reducing trivalent europium ions in doped samples. Thermal analysis of the precursors, performed by TG and DTA, revealed that the crystallization of SrAl{sub 2}O{sub 4} phase occurred at approximately 1060 °C. X-ray diffraction showed that the samples, before and after sintering, had monoclinic and hexagonal phases formation. DLS technique revealed the presence of nanosized and micrometric particles, and particle agglomerates, confirmed by SEM images. Micrographs of the fracture surface of a sintered pellet revealed a high degree of densification caused by heat treatment. Photoluminescence measurements showed that the samples after synthesis and before heat treatment with laser had reddish emission, composed of characteristic narrow emission lines from Eu{sup 3+} and more intense emission when the samples were excited at 265 nm. The laser treatment promoted the reduction of Eu{sup 3+} to Eu{sup 2+} and this effect was confirmed by the presence of a wide emission band in the green region of the spectrum with a maximum emission obtained after excitation at 350 nm. The luminescent decay time of the thermally treated sample was approximately 100 min. Via XRF measurements of acquired frit and DTA and TG of the frit, pigment and mixtures of both, it was noticed good compatibility in terms of thermal processes, that indicated that the pigment has a potential to be used in ceramic tiles. (author)

Electrochemical corrosion behavior of composite MAO/sol-gel coatings on magnesium alloy AZ91D using combined micro-arc oxidation and sol-gel technique

International Nuclear Information System (INIS)

Shang Wei; Chen Baizhen; Shi Xichang; Chen Ya; Xiao Xiang

2009-01-01

Protective composite coatings were obtained on a magnesium alloy by micro-arc oxidation (MAO) and sol-gel technique. The coatings consisted of a MAO layer and a sol-gel layer. The microstructure and composition of the MAO coating and the composite coatings were analyzed by scanning electron microscopy (SEM) and energy dispersive X-rays (EDX). Potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and total immersion tests were used to evaluate the corrosion behavior of these coatings in a 3.5 wt.% NaCl solution. The results show that the sol-gel layer provides corrosion protection by physically sealing the pores in the MAO coating and acting as a barrier. The composite coatings can suppress the corrosion process by preventing the corrosive ions from transferring or diffusing to the magnesium alloy substrate. This enhances the corrosion resistance of the magnesium alloy AZ91D significantly

Controlled release of vancomycin from thin sol-gel films on implant surfaces successfully controls osteomyelitis.

Science.gov (United States)

Adams, Christopher S; Antoci, Valentin; Harrison, Gerald; Patal, Payal; Freeman, Terry A; Shapiro, Irving M; Parvizi, Javad; Hickok, Noreen J; Radin, Shula; Ducheyne, Paul

2009-06-01

Peri-prosthetic infection remains a serious complication of joint replacement surgery. Herein, we demonstrate that a vancomycin-containing sol-gel film on Ti alloy rods can successfully treat bacterial infections in an animal model. The vancomycin-containing sol-gel films exhibited predictable release kinetics, while significantly inhibiting S. aureus adhesion. When evaluated in a rat osteomyelitis model, microbiological analysis indicated that the vancomycin-containing sol-gel film caused a profound decrease in S. aureus number. Radiologically, while the control side showed extensive bone degradation, including abscesses and an extensive periosteal reaction, rods coated with the vancomycin-containing sol-gel film resulted in minimal signs of infection. MicroCT analysis confirmed the radiological results, while demonstrating that the vancomycin-containing sol-gel film significantly protected dense bone from resorption and minimized remodeling. These results clearly demonstrate that this novel thin sol-gel technology can be used for the targeted delivery of antibiotics for the treatment of periprosthetic as well as other bone infections. Copyright 2008 Orthopaedic Research Society

Preparation of ThO2 sols having colloid-size distributions suitable for gelation into microspheres

International Nuclear Information System (INIS)

Yamagishi, Shigeru; Takahashi, Yoshihisa; Shiba, Koreyuki

1984-01-01

Production conditions of ThO 2 sols suitable for gelling into crackfree microspheres in an external gelation process were studied. The sols were prepared under pH control and colloid size distributions of the resulting sols were determined. The gelation was carried out by using hexone as a drop formation medium and ammonia as a gelling agent. The crackfree gelation was achieved by the use of ThO 2 sols produced under favorable pH, which were large in colloid size and high in colloid fraction. ''Preneutralization'' preceding the pH control is also important for the good sols. Analyzing the colloid fraction, colloid size and crystallite size of sol, it was found that, under the favorable pH, colloid nuclei generating at early stages grow in the form of single-crystals with their number kept constant and, after cooling, they exist as polycrystalline colloids. The mechanism of cracking is also discussed. (author)

The Influence of Microgravity on Silica Sol-Gel Formation

Science.gov (United States)

Sibille, L.; Smith, D. D.; Cronise, R.; Hunt, A. J.; Wolfe, D. B.; Snow, L. A.; Oldenberg, S.; Halas, N.; Rose, M. Franklin (Technical Monitor)

2000-01-01

We discuss space-flight experiments involving the growth of silica particles and gels. The effect of microgravity on the growth of silica particles via the sol-gel route is profound. In four different recipes spanning a large range of the parameter space that typically produces silica nanoparticles in unit-gravity, low-density gel structures were instead formed in microgravity. The particles that did form were generally smaller and more polydisperse than those grown on the ground. These observations suggest that microgravity reduces the particle growth rate, allowing unincorporated species to form aggregates and ultimately gel. Hence microgravity favors the formation of more rarefied structures, providing a bias towards diffusion-limited cluster-cluster aggregation. These results further suggest that in unit gravity, fluid flows and sedimentation can significantly perturb sol-gel substructures prior to gelation and these deleterious perturbations may be "frozen" into the resulting microstructure. Hence, sol-gel pores may be expected to be smaller, more uniform, and less rough when formed in microgravity.

Sol-gel Technology and Advanced Electrochemical Energy Storage Materials

Science.gov (United States)

Chu, Chung-tse; Zheng, Haixing

1996-01-01

Advanced materials play an important role in the development of electrochemical energy devices such as batteries, fuel cells, and electrochemical capacitors. The sol-gel process is a versatile solution for use in the fabrication of ceramic materials with tailored stoichiometry, microstructure, and properties. This processing technique is particularly useful in producing porous materials with high surface area and low density, two of the most desirable characteristics for electrode materials. In addition,the porous surface of gels can be modified chemically to create tailored surface properties, and inorganic/organic micro-composites can be prepared for improved material performance device fabrication. Applications of several sol-gel derived electrode materials in different energy storage devices are illustrated in this paper. V2O5 gels are shown to be a promising cathode material for solid state lithium batteries. Carbon aerogels, amorphous RuO2 gels and sol-gel derived hafnium compounds have been studied as electrode materials for high energy density and high power density electrochemical capacitors.

Apartes desde la inteligencia artificial

OpenAIRE

Luis Carlos Torres Soler

1998-01-01

El estudio y desarrollo de la inteligencia artificial no debe centrarse sólo en la creación de software o hardware que permita realizar procesos algorítmicos o heurísticos en el computador, de tal forma que produzcan soluciones óptimas y eficientes al resolver un problema complejo, ya sea de manejo de información o de toma de decisiones, o crear máquinas que tengan buena apariencia del ser humano; se debe, sobre todo, analizar la parte neurológica y sicológica que presenta el individuo al sol...

Efecto del número de aplicaciones de cloprostenol sobre la regresión de cuerpos lúteos, el retorno al celo y la ovulación, después de un tratamiento superovulatorio en donantes de embriones bovinos

OpenAIRE

C. Jiménez; R. Mapletoft; A. Tribulo; J. V. Garzón; Cabra C.; G. Bo

2011-01-01

El objetivo del presente trabajo fue evaluar la respuesta de la aplicación doble o triple de prostaglandina sobre la regresión de CL, ovulación y retorno al celo después de un tratamiento superovulatorio en vacas donantes de embriones. Para este experimento se tomaron 44 vacas asignadas al azar a dos grupos de tratamiento. Al primero (n = 23; CLO 0 & 7) se le aplicó una dosis de 500 μg de cloprostenol los días 0 (denominado día de la colecta) y 7; al segundo grupo (n = 21; CLO 0, 1 & 7) se le...

Sol-Gel Derived, Nanostructured Oxide Lubricant Coatings

National Research Council Canada - National Science Library

Taylor, Douglas

2000-01-01

In this program, we deposited oxide coatings of titanium and nickel by wet-chemical deposition methods, also referred to as sol-gel, which showed excellent tribological properties in previous investigations...

El tipo de cambio renminbi-dólar y su impacto sobre las exportaciones e Inversión Extranjera Directa en México

OpenAIRE

Vásquez Galán, Belem Iliana; Calderón Villarreal, Cuauhtémoc

2017-01-01

Resumen Este es un análisis del efecto que tiene una fluctuación del tipo de cambio renminbi-dólar sobre las exportaciones mexicanas dirigidas al mercado estadounidense y sobre la inversión extranjera directa procedente de ese país. Las estimaciones de un vector de corrección de error, con datos de 1995 a 2015, indican que una depreciación del renminbi reduce el crecimiento de las exportaciones mexicanas en 2.01 por ciento, pero no tiene efecto sobre la IED. Esto implica que, al ser competido...

Foliar application of two silica sols reduced cadmium accumulation in rice grains

International Nuclear Information System (INIS)

Liu Chuanping; Li Fangbai; Luo Chunling; Liu Xinming; Wang Shihua; Liu Tongxu; Li Xiangdong

2009-01-01

In the present study, pot experiments were conducted to investigate the effects of foliar application of two silica (Si) sols on the alleviation of cadmium (Cd) toxicity in contaminated soil to rice. Results showed that the foliar application of Si sols significantly increased the dry weight of grains (without husk) and shoots in rice grown in Cd contaminated soil, whereas the Cd concentration in the grains and shoots decreased obviously. The total accumulation of Cd in rice grains also decreased with the application of both of the Si sols, but no significant effect was found on the Cd accumulation in the shoots. For the optimal effect, Si-sol-B should be foliar applied at the tillering-stage during rice growth. The mechanism of Si foliar application to alleviate the toxicity and accumulation of Cd in grains of rice may be related to the probable Cd sequestration in the shoot cell walls

Efficacy of a new tan doped sol-gel sorbent for uptake of zinc

International Nuclear Information System (INIS)

Khan, A.; Ahmed, S.; Riaz, M.; Mahmood, F.; Younas Khokhar, M.

2003-01-01

A TAN (1-(2-Thiazolylazo)-2-naphthol) doped sol gel silica sorbent (reddish colour, porous, stable, hard, non-swelling) were prepared and investigated for the removal of Zn (II) from aqueous solutions. The kinetics, adsorption isotherm, equilibration time and pH effect on the removal were studied from non competitive aqueous solution to optimize the conditions to be utilized on a large scale. Fast equilibration was observed and adsorption equilibria were reached within 30 minutes. Adsorption of zinc ions on the blank (un-doped) sol gel was found negligible. The maximum adsorption of Zn (II) ions onto the TAN doped sol-gel from single solutions were 2.33 mg/g (0.035 mmol/g). TAN doped sol gel can be regenerated through washing with a solution of 0.1 M HCl solution. The maximum regeneration value was as high as 99.0%. The TAN-doped sol gel silica is suitable at least for four adsorption-desorption cycles without experiencing considerable loss of adsorption capacity. The uptake route and the nature of the Zn-TAN complex have been discussed. (orig.)

The conversion of the thermal energy of plasma in the SOL of tokamaks

International Nuclear Information System (INIS)

Nedospasov, A.V.; Nenova, N.V.

2008-01-01

When the plasma expands across the confining magnetic field, a part of its thermal energy is converted to electrical energy. In the SOL of tokamaks, the motion of the plasma across the field due to turbulent processes is accompanied by its departure along the open lines of the magnetic field. The conversion of thermal energy is taken into account in theoretical studies devoted to the physics of plasma in the SOL; however, this conversion is ignored in numerical models, for example, in B2-SOLPS4.0. This paper deals with thermal-to-electrical energy conversion in the SOL of tokamaks. It is demonstrated that the part of the thermal energy subjected to conversion to electrical energy forms an appreciable part of the total energy flowing in the SOL. In ITER, this fraction may be as high as 20-25%. The electrical energy generated in the SOL volume is liberated in the form of Joule heat in a relatively cold plasma in the vicinity of diverter plates or directly on these plates. (letter)

Evaluación de la información sanitaria disponible en internet sobre la vacuna antigripal

OpenAIRE

I. Hernández-García; R. González Celador

2014-01-01

Fundamento: La calidad de la información sanitaria en internet preocupa a gobiernos y usuarios. Nuestro objetivo fue determinar en qué medida la información sobre la vacuna antigripal se adhiere al gold estándar representado por lo establecido por el Ministerio de Sanidad español. Material y métodos: Entre junio-julio 2014 se evaluó la adhesión al gold estándar de la información sobre indicaciones, efectos adversos y contraindicaciones de la vacuna. Dicha información se obtuvo a través de Goo...

Nanostructured sol-gel coatings doped with cerium nitrate as pre-treatments for AA2024-T3

International Nuclear Information System (INIS)

Zheludkevich, M.L.; Serra, R.; Montemor, M.F.; Yasakau, K.A.; Salvado, I.M. Miranda; Ferreira, M.G.S.

2005-01-01

Nanostructured hybrid sol-gel coatings doped with cerium ions were investigated in the present work as pre-treatments for the AA2024-T3 alloy. The sol-gel films have been synthesized from tetraethylorthosilicate (TEOS) and 3-glycidoxypropyltrimethoxysilane (GPTMS) precursors. Additionally the hybrid sol was doped with zirconia nanoparticles prepared from hydrolyzed tetra-n-propoxyzirconium (TPOZ). Cerium nitrate, as corrosion inhibitor, was added into the hybrid matrix or into the oxide nanoparticles. The chemical composition and the structure of the hybrid sol-gel films were studied by XPS (X-ray photoelectron spectroscopy) and AFM (atomic force microscopy), respectively. The evolution of the corrosion protection properties of the sol-gel films was studied by EIS (electrochemical impedance spectroscopy), which can provide quantitative information on the role of the different pre-treatments. Different equivalent circuits, for different stages of the corrosion processes, were used in order to model the coating degradation. The models were supported by SEM (scanning electron microscopy) measurements. The results show that the sol-gel films containing zirconia nanoparticles present improved barrier properties. Doping the hybrid nanostructured sol-gel coatings with cerium nitrate leads to additional improvement of the corrosion protection. The zirconia particles present in the sol-gel matrix seem to act as nanoreservoirs providing a prolonged release of cerium ions. The nanostructured sol-gel films doped with cerium nitrate can be proposed as a potential candidate for substitution of the chromate pre-treatments for AA2024-T3

Functionalization of sol-gel zirconia composites with europium complexes

International Nuclear Information System (INIS)

Danchova, Nina; Gutzov, Stoyan

2014-01-01

Different sol-gel strategies based on functionalization of ZrO 2 :Eu microparticles with 1,10-phenanthroline (phen) and incorporation of colloidal Eu(phen) 2 (NO 3 ) 3 into zirconia have been used to obtain hybrid sol-gel composites with controlled optical properties. The process leads to materials with quantum yields of about 48 % monitoring the 615 nm emission line at 350 nm excitation. Excitation/luminescence spectroscopy, diffuse reflectance spectroscopy and X-ray diffraction have been used to characterize the hybrid zirconia composites. (orig.)

Third Order Susceptibility of Platinum Sulfide Sol

National Research Council Canada - National Science Library

LaiHing, Kenneth

1992-01-01

.... Experimentally this is determined using degenerate four-wave mixing (DFWM). Pure sulfur sol was prepared by dissolving the solid sulfur in hydrazine, followed by addition of distilled water with vigorous stirring...

Intervención educativa comunitaria sobre la diabetes en el ámbito de la atención primaria

Directory of Open Access Journals (Sweden)

Ana Gladys Aráuz

2001-03-01

Full Text Available Objetivos. Ofrecer una alternativa de educación sobre la diabetes con la participación de pacientes, familiares y personal sanitario, adaptada a las condiciones locales y a las necesidades sentidas por estas personas. Métodos. Se describe la metodología utilizada en una intervención educativa comunitaria sobre la diabetes de tipo 2, dirigida al primer nivel de atención. El estudio se realizó en el área de salud de El Guarco, Costa Rica. En una primera etapa se hizo un estudio cualitativo sobre los conocimientos y prácticas de los pacientes y del personal sanitario en relación con la prevención y el tratamiento de la diabetes y sobre la disponibilidad de alimentos en la comunidad. A partir de estos resultados, se desarrolló la metodología educativa, para lo cual se diseñaron un manual y dos procesos de capacitación sobre la diabetes, uno dirigido al personal sanitario y otro a los pacientes. Además, se desarrollaron estrategias comunitarias para dar sostenibilidad al proceso educativo. Resultados. Se verificó que los pacientes no asocian el origen de la enfermedad con los antecedentes familiares ni el sobrepeso, que confunden los síntomas de hiperglucemia e hipoglucemia y que no hay homogeneidad en los mensajes de nutrición que reciben. Sobre la base del manual sobre diabetes, se capacitó al personal sanitario, cuyos conocimientos sobre el tratamiento y la prevención de la diabetes y sobre la metodología educativa mejoraron (promedio de 85%. A su vez, el personal sanitario capacitó a los pacientes diabéticos de su comunidad (edad: 57,0 ± 8,9 años, 92% mujeres, quienes mostraron después del curso una disminución de la glucemia, de 189 ± 79 mg/dL a 157 ± 48 mg/dL (P = 0,03, y de la hemoglobina glucosilada, de 11,3 ± 2,4% a 9,7 ± 2,3% (P = 0,05. No hubo cambios significativos del peso ni del perfil lipídico, a excepción de los triglicéridos, que disminuyeron (P = 0,04. Conclusiones. El nivel primario de atenci

(I) Informe sobre conflicto violento en colombia (2011–2012)

OpenAIRE

2014-01-01

Las negociaciones de paz entre el gobierno nacional y las FARC avanzan de modo considerable. Al momento del cierre del presente informe –julio de 2014–, se construyó un acuerdo sobre los tres primeros puntos de la agenda –la reforma agraria, la participación política y las drogas ilícitas–. Sin duda la negociación progresa, los puntos sobre los que se trazó un acuerdo tocan dimensiones neurálgicas de la vida colectiva: el agro y su atraso histórico, la democracia y sus cierres, el narcotráfic...

utilisation des donnees pour l'evaluation de l'heterogeneite des sols

African Journals Online (AJOL)

AISA

étude a permis de caractériser l'hétérogénéité des sols ferrallitiques, à travers sa couleur. Mots-clés : Couleur ... ainsi qu'à l'application des recommandations des doses de fertilisant. ..... de « système sol » en zone de contact forêt- savane du ...

Efectos subletales de la lambda-cialotrina sobre eisenia fetida (Annelida, Oligochaeta, Lumbricidae)

OpenAIRE

Ricardo, Tamara; Maitre, Maria Ines; Rodriguez, Alba Rut

2017-01-01

El uso intensivo de agroquímicos provoca efectos indeseables sobre la fauna no blanco. Dentro de la misma, los oligoquetos contribuyen a mantener la estructura y fertilidad del suelo. La lambda-cialotrina es uno de los insecticidas piretroides más utilizados en Argentina, pero son escasos los datos existentes acerca de su toxicidad sobre oligoquetos. Los objetivos de este trabajo fueron evaluar mediante bioensayos de toxicidad crónica los efectos de lambda-cialotrina (producto comercial al 5%...

Opportunity's View After Drive on Sol 1806 (Stereo)

Science.gov (United States)

2009-01-01

[figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11816 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11816 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this stereo, full-circle view of the rover's surroundings just after driving 60.86 meters (200 feet) on the 1,806th Martian day, or sol, of Opportunity's surface mission (Feb. 21, 2009). North is at the center; south at both ends. This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. Tracks from the drive extend northward across dark-toned sand ripples and light-toned patches of exposed bedrock in the Meridiani Planum region of Mars. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). Engineers designed the Sol 1806 drive to be driven backwards as a strategy to redistribute lubricant in the rovers wheels. The right-front wheel had been showing signs of increased friction. The rover's position after the Sol 1806 drive was about 2 kilometer (1.2 miles) south southwest of Victoria Crater. Cumulative odometry was 14.74 kilometers (9.16 miles) since landing in January 2004, including 2.96 kilometers (1.84 miles) since climbing out of Victoria Crater on the west side of the crater on Sol 1634 (August 28, 2008). This view is presented as a cylindrical-perspective projection with geometric seam correction.

Sílica solúvel em solos Soluble silica in soils

Directory of Open Access Journals (Sweden)

Bernardo van Raij

1973-01-01

Full Text Available Determinou-se a silica solúvel nos horizontes superficial e B2 de 44 perfis de solos do Estado de São Paulo. A extração da silica com solução 0,0025M de cloreto de cálcio evitou a dispersão dos solos e forneceu resultados em média apenas 8% menores do que a silica solúvel em água. Os resultados variaram de 2,2 a 92,2 ppm de SiO2. Verificou-se que, para solos com teores semelhantes de argila, os teores de silica solúvel foram maiores para solos com horizonte B textural, quando comparados com solos de horizonte B latossólico. Dentro dos agrupamentos de solos com horizonte B textural e horizonte B latossólico, os teores de silica solúvel foram maiores para os solos mais argilosos. Não foi observada relação entre silica solúvel e o pH dos solos.The extraction of soluble silica of soils with 0.0025M calcium chloride solution avoided dispersion of clay and results were on the average only 8% lower than water soluble silica. The results for surface and B2 horizons of 44 soil profiles of the State of São Paulo varied between 2.2 and 92.9 ppm of SiO2. For soils with similar clay contents, soluble silica was higher for soil with argillic B horizons as compared with soils with oxic B horizons. Within each group of soils, higher soluble silica results were associated with higher clay contents. Soluble silica apparently was not related to soil pH.

SOL-Gel microspheres and nanospheres for controlled release applications

International Nuclear Information System (INIS)

Barbe, C.; Beyer, R.; Kong, L.; Blackford, M.; Trautman, R.; Bartlett, J.

2002-01-01

We present a novel approach to the synthesis of inorganic sol-gel microspheres for encapsulating organic and bioactive molecules, and controlling their subsequent release kinetics. The bioactive species are incorporated, at ambient temperature, into the inorganic particles using an emulsion gelation process. Independent control of the release rate (by adapting the nanostructure of the internal pore network to the physico-chemical properties of the bioactive molecules) and particle size (by tailoring the emulsion chemistry) is demonstrated. Sol-gel chemistry has been shown to be a flexible technique for producing inorganic silica matrices with tailored microstructures, which can be used for the encapsulation and controlled release of organic and bioactive molecules. The present paper extends this concept by combining sol-gel chemistry with an emulsion approach for producing inorganic particles with controlled dimensions, and demonstrates how the particle size and microstructure can be independently controlled. Sol-Gel Chemistry and Encapsulation of Model Compounds. A stock solution of 4-(2-hydroxy-l-naphthylazo) benzene sulfonic acid (Orange II) was produced by dissolving Orange II in water (0.1 wt%), and adjusting the pH to the required value. Sol-gel solutions were subsequently prepared by mixing the aqueous solution with tetramethylorthosilicate (TMOS) and methanol (MeOH), to achieve H 2 O:TMOS (W] and MeOH:TMOS mole ratios (D) of four. The resulting solution was stirred and left to age at ambient temperature for one day. A transparent emulsion was prepared by mixing selected surfactants and organic solvents. The surfactants used included sorbitan monooleate, sorbitan monolaurate and bis-2-ethylhexylsulfo-succinate (AOT), while the organic phase was typically chosen from the group consisting of kerosene, hexane, heptane, octane, decane, dodecane and cyclohexane. The sol-gel solution was added to the emulsion, and the resulting mixture was stirred at 500 rpm for

Minimally Adhesive, Advanced Non-toxic Coatings of Dendrimeric Catalysts in Sol-Gel Matrices

Science.gov (United States)

2015-10-19

Catalysts in Sol -Gel Matrices 5a. CONTRACT NUMBER 5b. GRANT NUMBER N00014-09-1-0217 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Detty, Michael R. 5d...Technical Report for ONR N00014-09-1-0217 Minimally Adhesive, Advanced Non-toxic Coatings of Dendrimeric Catalysts in Sol -Gel Matrices Michael R. Detty, PI...Environmentally benign sol -gel antifouling and foul-releasing coatings. Ace. Chem. Res. 2014, 47, 678-687. 11) Alberto, E. E.; Müller, L. M

PON-Sol: prediction of effects of amino acid substitutions on protein solubility.

Science.gov (United States)

Yang, Yang; Niroula, Abhishek; Shen, Bairong; Vihinen, Mauno

2016-07-01

Solubility is one of the fundamental protein properties. It is of great interest because of its relevance to protein expression. Reduced solubility and protein aggregation are also associated with many diseases. We collected from literature the largest experimentally verified solubility affecting amino acid substitution (AAS) dataset and used it to train a predictor called PON-Sol. The predictor can distinguish both solubility decreasing and increasing variants from those not affecting solubility. PON-Sol has normalized correct prediction ratio of 0.491 on cross-validation and 0.432 for independent test set. The performance of the method was compared both to solubility and aggregation predictors and found to be superior. PON-Sol can be used for the prediction of effects of disease-related substitutions, effects on heterologous recombinant protein expression and enhanced crystallizability. One application is to investigate effects of all possible AASs in a protein to aid protein engineering. PON-Sol is freely available at http://structure.bmc.lu.se/PON-Sol The training and test data are available at http://structure.bmc.lu.se/VariBench/ponsol.php mauno.vihinen@med.lu.se Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Dos derechos al revés: reflexiones sobre los derechos a la vida y a la paz en el mundo actual

Directory of Open Access Journals (Sweden)

Saúl Franco

2007-01-01

Full Text Available El documento presenta una síntesis de los conceptos de vida y paz y de ambos como derechos humanos. Reconoce que en la actual situación, ambos derechos están siendo sistemática y gravemente negados al interior de muchos países y en el escenario internacional. A partir de sintetizar los aportes de diferentes disciplinas acerca de lo que es la vida, el documento se centra en el reconocimiento de la vida como el derecho esencial y como la base de todos los demás derechos. Se presenta luego un panorama realista y muy preocupante del estado actual de ambos derechos en el mundo. Se aportan cifras y datos sobre homicidios, desplazamientos forzosos por la violencia, refugiados y secuestrados, y sobre diferentes formas de violaciones a los derechos a la vida y a la paz en algunos de los conflictos armados más agudos y representativos en la actualidad, entre ellos la invasión y consiguiente guerra en Irak, y los conflictos de Afganistán, Israel y Palestina y Sudán, con una referencia especial a la situación colombiana. El material termina señalando algunos posibles mecanismos y acciones para contribuir desde la posición de cada cual a la reducción de las violaciones a estos dos derechos humanos y a fomentar su vigencia.

Functionalizable Sol-Gel Silica Coatings for Corrosion Mitigation

Directory of Open Access Journals (Sweden)

Jolanta Gąsiorek

2018-01-01

Full Text Available Corrosion is constantly a major problem of the world economy in the field of metal products, metal processing and other areas that utilise metals. Previously used compounds utilizing hexavalent chromium were amongst the most effective materials for corrosion protection but regulations have been recently introduced that forbid their use. Consequently, there is a huge drive by engineers, technologists and scientists from different disciplines focused on searching a new, more effective and environmentally-friendly means of corrosion protection. One novel group of materials with the potential to solve metal protection problems are sol-gel thin films, which are increasingly interesting as mitigation corrosion barriers. These environmentally-friendly and easy-to-obtain coatings have the promise to be an effective alternative to hexavalent chromium compounds using for anti-corrosion industrial coatings. In this review the authors present a range of different solutions for slow down the corrosion processes of metallic substrates by using the oxides and doped oxides obtained by the sol-gel method. Examples of techniques used to the sol-gel coating examinations, in terms of anti-corrosion protection, are also presented.

Hydrogen permeation through sol-gel-coated iron during galvanostatic charging

International Nuclear Information System (INIS)

Zakorchemna, I.; Carmona, N.; Zakroczymski, T.

2008-01-01

One-layer sol-gel silica-zirconia and two-layer silica-zirconia and zirconia coatings were deposited on one side of iron membranes by spin-coating, densified in air and annealed up to 800 deg. C in vacuum. Hydrogen permeation through the membranes, coated and uncoated, polarised cathodically under galvanostatic control in 0.1 M NaOH solution was studied using the electrochemical permeation technique. During the initial period, the effect of the sol-gel coatings was insignificant. However, the coatings quite efficiently prevented the iron surface become more active to hydrogen entry during a long-lasting cathodic polarisation. In addition, the electrochemical-corrosion behaviour of the coated iron and the effect of the sol-gel coatings on the effective diffusivity of hydrogen in the coated membranes were studied. On the basis of the polarisation curves and the hydrogen permeation data it was proved that the sol-gel coatings blocked the iron surface for the hydrogen evolution reaction and, consequently, for the hydrogen entry into iron. The effective coating coverage was determined by comparison of the hydrogen fluxes permeating the coated and uncoated membranes. Finally the real concentration of hydrogen beneath the uncoated iron sites and the amount of hydrogen stored in a membrane were evaluated

Critical ageing and chemistry of nanocrystalline hydroxyapatite sol-gel solutions

Energy Technology Data Exchange (ETDEWEB)

Chai, C.S.; Gross, K.A.; Kannangara, K.; Ben-Nissan, B. [University of Technology, Sydney, NSW (Australia). Department of Chemistry, Materials and Forensic Sciences; Hanley, L. [University of Illinois at Chicago, (United States). Department of Chemistry

1998-12-31

In previous work we have demonstrated that using alkoxide precursors, it is possible to produce crystalline hydroxyapatite coatings with potential uses in orthopaedic and dental applications. However, to produce monophasic hydroxyapatite coatings, sols must be aged for a minimum of 24 hours prior to deposition. {sup 31}P NMR has been used to analyse chemical changes occurring in the sol during the ageing process and have revealed that P-O-C bonds present in the precursor material are gradually replaced by P-O-Ca bonds with an accompanying change in oxidation state from P(III) to P(V). Thermal analysis was used to examine hydrolysed gels and showed that sols aged less than 24 hours contain unreacted calcium diethoxide which produces CaO upon heating. These findings have been confirmed by x-ray diffraction. Copyright (1998) Australasian Ceramic Society 16 refs., 4 figs.

Recent progress towards a quantitative description of filamentary SOL transport

DEFF Research Database (Denmark)

Carralero, D.; Siccinio, M.; Komm, M.

2017-01-01

A summary of recent results on filamentary transport, mostly obtained with the ASDEX-Upgrade tokamak (AUG), is presented and discussed in an attempt to produce a coherent picture of scrape-off layer (SOL) filamentary transport. A clear correlation is found between L-mode density shoulder formation...... in the outer midplane and a transition between the sheath-limited and the inertial filamentary regimes. Divertor collisionality is found to be the parameter triggering the transition. A clear reduction of the ion temperature takes place in the far SOL after the transition, both for the background......-mode plasmas, although a secondary threshold related to deuterium fueling is observed. EMC3-EIRENE simulations of neutral dynamics show that an ionization front near the main chamber wall is formed after the shoulder formation. Finally, a clear increase of SOL opacity to neutrals is observed, associated...

Critical ageing and chemistry of nanocrystalline hydroxyapatite sol-gel solutions

International Nuclear Information System (INIS)

Chai, C.S.; Gross, K.A.; Kannangara, K.; Ben-Nissan, B.; Hanley, L.

1998-01-01

In previous work we have demonstrated that using alkoxide precursors, it is possible to produce crystalline hydroxyapatite coatings with potential uses in orthopaedic and dental applications. However, to produce monophasic hydroxyapatite coatings, sols must be aged for a minimum of 24 hours prior to deposition. 31 P NMR has been used to analyse chemical changes occurring in the sol during the ageing process and have revealed that P-O-C bonds present in the precursor material are gradually replaced by P-O-Ca bonds with an accompanying change in oxidation state from P(III) to P(V). Thermal analysis was used to examine hydrolysed gels and showed that sols aged less than 24 hours contain unreacted calcium diethoxide which produces CaO upon heating. These findings have been confirmed by x-ray diffraction. Copyright (1998) Australasian Ceramic Society

Contabilidad del impuesto sobre beneficios

OpenAIRE

Luceño Martínez, Haizea

2017-01-01

Este Trabajo Fin de Grado pretende dar una explicación al tratamiento contable del Impuesto de Sociedades. Siendo un impuesto que hay que contabilizar, pero que se calcula siguiendo criterios fiscales, lleva a tener que realizar ajustes que tendrán su repercusión contable. El punto de partida no es otra que la norma de registro y valoración 13ª del PGC, que versa sobre cómo hay que proceder a contabilizar el Gasto por Impuesto de Sociedades, que se compone tanto del Gasto por Impuesto Co...

La desintegración familiar y el rendimiento académico de los estudiantes del V Ciclo de la Red 01 Sol Mar y Arena, UGEL 04-Comas, 2012

OpenAIRE

Mancisidor Pasco, Freedy Edulfo

2013-01-01

La presente investigación trató sobre la relación entre la desintegración familiar y el rendimiento académico en el área de comunicación integral en los estudiantes del V ciclo Red Nº 01 “Sol, Mar y Arena”-UGEL 04-Comas, El objetivo general fue establecer la relación entre la desintegración familiar y el rendimiento académico. El diseño de investigación es no experimental, transeccional y correlacional; la muestra estuvo conformada por 288 estudiantes del V, ciclo a quien...

Efecto de la edad al primer parto y los días abiertos en un bovino doble propósito sobre la huella hídrica y de carbono

Directory of Open Access Journals (Sweden)

Raúl Andrés Molina Benavides

2016-12-01

Full Text Available La actividad ganadera contribuye con la emisión de gases de efecto invernadero (EGEI y el consumo de agua fresca (CA. Por ende, el objetivo de esta investigación fue estimar el efecto de la edad al primer parto (EPP y los días abiertos (DA en un bovino doble propósito en pastoreo, trópico bajo colombiano, sobre las EGEI y el CA. Esta estimación se logró integrando 4 metodologías existentes: Dinámica de Sistemas, Large Ruminal Nutrition System, Huella de carbono y Huella hídrica. Durante toda su vida, 91 meses, desde el nacimiento hasta el sacrificio, la vaca produjo 5.879 kg de leche -4 lactancias-, emitió 16.066 kg CO2eq y consumió 12.804.569 L de agua. Al disminuir la EPP en un mes, el CA y  las EGEI se redujeron en 123.156 l y 155 kg CO2eq, respectivamente. Cuando se  mermaron los DA en 21, las EGEI bajaron 647 kg CO2eq y el CA se redujo en 455.455 L. Parámetros reproductivos como la EPP y los DA tienen una fuerte influencia sobre la dinámica del animal en el hato,  afectando su productividad, emisiones de gases de efecto invernadero y consumo de agua. 

Laser sintering of doped strontium aluminate via modified sol-gel for use as a ceramic pigment

International Nuclear Information System (INIS)

Soares, F.M. dos S.; Valerio, M.E.G.

2017-01-01

Powder of Dy"3"+ co-doped SrAl_2O_4 :Eu"3"+ was produced via proteic sol-gel method, a modified sol-gel route which allows the formation of oxides at lower temperatures than other methods. CO_2 laser sintering was used as a method for heat treatment, effective in reducing trivalent europium ions in doped samples. Thermal analysis of the precursors, performed by TG and DTA, revealed that the crystallization of SrAl_2O_4 phase occurred at approximately 1060 °C. X-ray diffraction showed that the samples, before and after sintering, had monoclinic and hexagonal phases formation. DLS technique revealed the presence of nanosized and micrometric particles, and particle agglomerates, confirmed by SEM images. Micrographs of the fracture surface of a sintered pellet revealed a high degree of densification caused by heat treatment. Photoluminescence measurements showed that the samples after synthesis and before heat treatment with laser had reddish emission, composed of characteristic narrow emission lines from Eu"3"+ and more intense emission when the samples were excited at 265 nm. The laser treatment promoted the reduction of Eu"3"+ to Eu"2"+ and this effect was confirmed by the presence of a wide emission band in the green region of the spectrum with a maximum emission obtained after excitation at 350 nm. The luminescent decay time of the thermally treated sample was approximately 100 min. Via XRF measurements of acquired frit and DTA and TG of the frit, pigment and mixtures of both, it was noticed good compatibility in terms of thermal processes, that indicated that the pigment has a potential to be used in ceramic tiles. (author)

Tantala-based sol-gel coating for capillary microextraction on-line coupled to high-performance liquid chromatography.

Science.gov (United States)

Tran, MinhPhuong; Turner, Erica B; Segro, Scott S; Fang, Li; Seyyal, Emre; Malik, Abdul

2017-11-03

A sol-gel organic-inorganic hybrid sorbent, consisting of chemically integrated tantalum (V) ethoxide (TaEO) and polypropylene glycol methacrylate (PPGM), was developed for capillary microextraction (CME). The sol-gel sorbent was synthesized within a fused silica capillary through hydrolytic polycondensation of TaEO and chemical incorporation of PPGM into the evolving sol-gel tantala network. A part of the organic-inorganic hybrid sol-gel network evolving in the vicinity of the capillary walls had favorable conditions to get chemically bonded to the silanol groups on the capillary surface forming a surface-bonded coating. The newly developed sol-gel sorbent was employed to isolate and enrich a variety of analytes from aqueous samples for on-line analysis by high-performance liquid chromatography (HPLC) equipped with a UV detector. CME was performed on aqueous samples containing trace concentrations of analytes representing polycyclic aromatic hydrocarbons, ketones, alcohols, amines, nucleosides, and nucleotides. This sol-gel hybrid coating provided efficient extraction with CME-HPLC detection limits ranging from 4.41pM to 28.19 pM. Due to direct chemical bonding between the sol-gel sorbent coating and the fused silica capillary inner surface, this sol-gel sorbent exhibited enhanced solvent stability. The sol-gel tantala-based sorbent also exhibited excellent pH stability over a wide pH range (pH 0-pH 14). Furthermore, it displayed great performance reproducibility in CME-HPLC providing run-to-run HPLC peak area relative standard deviation (RSD) values between 0.23% and 3.83%. The capillary-to-capillary RSD (n=3), characterizing capillary preparation method reproducibility, ranged from 0.24% to 4.11%. The results show great performance consistency and application potential for the sol-gel tantala-PPGM sorbent in various fields including biomedical, pharmaceutical, and environmental areas. Copyright © 2017 Elsevier B.V. All rights reserved.

Al filo del milenio: ¿quo vadis, educación física

OpenAIRE

Olivera Betrán, Javier

1999-01-01

Inmersos en plena discusión sobre el cambio, o no, del siglo y del milenio, abundan en estas fechas los análisis del siglo XX y, por extensión, sobre el segundo milenio de nuestra historia. Para el modelo occidental el año 2000 representa un cambio histórico (aunque amputando un año al siglo y, por ende, al milenio gracias a los avispados e impacientes manipuladores de fechas con evidentes fines consumistas y sensacionalistas), pues muy pocas generaciones de la humanidad han podido vivenciar ...

Opportunity's Surroundings After Sol 1820 Drive (Polar)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). This view is presented as a polar projection with geometric seam correction. North is at the top. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock.

Opportunity's Surroundings After Sol 1820 Drive (Vertical)

Science.gov (United States)

2009-01-01

NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). This view is presented as a vertical projection with geometric seam correction. North is at the top. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock.

Sol-gel precursors and products thereof

Science.gov (United States)

Warren, Scott C.; DiSalvo, Jr., Francis J.; Weisner, Ulrich B.

2017-02-14

The present invention provides a generalizable single-source sol-gel precursor capable of introducing a wide range of functionalities to metal oxides such as silica. The sol-gel precursor facilitates a one-molecule, one-step approach to the synthesis of metal-silica hybrids with combinations of biological, catalytic, magnetic, and optical functionalities. The single-source precursor also provides a flexible route for simultaneously incorporating functional species of many different types. The ligands employed for functionalizing the metal oxides are derived from a library of amino acids, hydroxy acids, or peptides and a silicon alkoxide, allowing many biological functionalities to be built into silica hybrids. The ligands can coordinate with a wide range of metals via a carboxylic acid, thereby allowing direct incorporation of inorganic functionalities from across the periodic table. Using the single-source precursor a wide range of functionalized nanostructures such as monolith structures, mesostructures, multiple metal gradient mesostructures and Stober-type nanoparticles can be synthesized. ##STR00001##

Una nota sobre la teoría de la firma bajo incertidumbre.

Directory of Open Access Journals (Sweden)

Moawia Alghalith

2010-05-01

Full Text Available En este artículo se muestra que el incremento en el nivel de riesgo de los precios reduce el nivel de producción óptimo en condiciones de aversión absoluta al riesgo creciente. Esto es, el impacto marginal del riesgo sobre el nivel de producción es independiente del tipo de aversión absoluta al riesgo (decreciente, constante o creciente.

Radiation hardening of sol gel-derived silica fiber preforms through fictive temperature reduction.

Science.gov (United States)

Hari Babu, B; Lancry, Matthieu; Ollier, Nadege; El Hamzaoui, Hicham; Bouazaoui, Mohamed; Poumellec, Bertrand

2016-09-20

The impact of fictive temperature (Tf) on the evolution of point defects and optical attenuation in non-doped and Er3+-doped sol-gel silica glasses was studied and compared to Suprasil F300 and Infrasil 301 glasses before and after γ-irradiation. To this aim, sol-gel optical fiber preforms have been fabricated by the densification of erbium salt-soaked nanoporous silica xerogels through the polymeric sol-gel technique. These γ-irradiated fiber preforms have been characterized by FTIR, UV-vis-NIR absorption spectroscopy, electron paramagnetic resonance, and photoluminescence measurements. We showed that a decrease in the glass fictive temperature leads to a decrease in the glass disorder and strained bonds. This mainly results in a lower defect generation rate and thus less radiation-induced attenuation in the UV-vis range. Furthermore, it was found that γ-radiation "hardness" is higher in Er3+-doped sol-gel silica compared to un-doped sol-gel silica and standard synthetic silica glasses. The present work demonstrates an effective strategy to improve the radiation resistance of optical fiber preforms and glasses through glass fictive temperature reduction.

Synthesis of Hollow Sphere and 1D Structural Materials by Sol-Gel Process.

Science.gov (United States)

Li, Fa-Liang; Zhang, Hai-Jun

2017-08-25

The sol-gel method is a simple and facile wet chemical process for fabricating advanced materials with high homogeneity, high purity, and excellent chemical reactivity at a relatively low temperature. By adjusting the processing parameters, the sol-gel technique can be used to prepare hollow sphere and 1D structural materials that exhibit a wide application in the fields of catalyst, drug or gene carriers, photoactive, sensors and Li-ion batteries. This feature article reviewed the development of the preparation of hollow sphere and 1D structural materials using the sol-gel method. The effects of calcination temperature, soaking time, pH value, surfactant, etc., on the preparation of hollow sphere and 1D structural materials were summarized, and their formation mechanisms were generalized. Finally, possible future research directions of the sol-gel technique were outlined.

Microstructural characterization of Al{sub 2}O{sub 3}: Eu with dosimetric purposes; Cracterizacion microestructural de Al{sub 2}O{sub 3}: Eu con fines dosimetricos

Energy Technology Data Exchange (ETDEWEB)

Mendoza A, D.; Espinosa P, M.E.; Gonzalez M, P.R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Rubio, E. [BUAP, Facultad de Ingenieria Quimica, 72570 Puebla (Mexico)

2004-07-01

In this work a microstructural analysis is presented, through Sem, EDS and XRD, of the alumina with Europium (Al{sub 2}O{sub 3}: Eu) synthesized by the sol gel method. According to those obtained results, a previous thermal treatment to 1000 C to the samples, induces the formation of the {gamma}-alumina phase for the samples that does not contain Eu; however when there is presence of this element, the {theta} alumina phase is obtained. Likewise, it was observed that the particle size is increased with the presence of Eu. When analyzing the thermoluminescent response (TL) induced by the gamma radiation, it was observed that the pure Al{sub 2}O{sub 3} presents an intense TL sign; while the Al{sub 2}O{sub 3}: Eu, the sign suffers a marked decrement. (Author)

LES RELATIONS ENTRE L’ERODABILITE DES SOLS ET LEURS PROPRIETES PHYSICO-MECANIQUES

Directory of Open Access Journals (Sweden)

I. C. Stanga

2005-10-01

Full Text Available L’érodabilité représente la susceptibilité des sols d’être érodés sous l’action des pluies, du ruissellement ou du vent. Cette susceptibilité est conditionnée par les propriétés physico-chimiques des sols. Dans l’article ci-dessous, on montre les relations qui existent entre l’érodabilité et les propriétés physico-mécaniques des sols, dont les plus importantes sont la granulométrie (surtout le rapport entre différentes fractions texturales, la structure, la densité, la permeabilité et la conductivité hydrauliques.

Thermodynamic analysis of sol-gel transition of gelatin in terms of water activity in various solutions.

Science.gov (United States)

Miyawaki, Osato; Omote, Chiaki; Matsuhira, Keiko

2015-12-01

Sol-gel transition of gelatin was analyzed as a multisite stoichiometric reaction of a gelatin molecule with water and solute molecules. The equilibrium sol-gel transition temperature, Tt , was estimated from the average of gelation and melting temperature measured by differential scanning calorimetry. From Tt and the melting enthalpy, ΔHsol , the equilibrium sol-to-gel ratio was estimated by the van't Hoff equation. The reciprocal form of the Wyman-Tanford equation, which describes the sol-to-gel ratio as a function of water activity, was successfully applied to obtain a good linear relationship. From this analysis, the role of water activity on the sol-gel transition of gelatin was clearly explained and the contributions of hydration and solute binding to gelatin molecules were separately discussed in sol-gel transition. The general solution for the free energy for gel-stabilization in various solutions was obtained as a simple function of solute concentration. © 2015 Wiley Periodicals, Inc.

Dynamics Research on the Gelling Course of Silica Sol

Institute of Scientific and Technical Information of China (English)

LUYi－chun; LIZai－geng

1995-01-01

Dreipping electrolytes into silica sol ,gelling reaction will occur,The research indicates:this is a complicated physicemistry course,which consists of a pre-reaction and a polymerizaion,The former controls the whole course,and in which electronic layers of the sol's particles be-come more and more thiner,but with incresing of the sol concentration,its control force will be diminished ,till the fast-coagulation ,the gelling couse becomes o-controlled,The latter is an in-finite polymeric chani-reaction.The result of gelatination is to produce a very big plymeric molecule-gel,which involves in all space,includes all water ,and its molecular weight is in-definite big.The researh also indicates:the dy-namic course of the gelling could be described quantitaively by an experience formula:lgt=-nlgc+B,All of the characteristic values have definite physical meaning,Electronic value of the contrary-inos is the biggest influential factor ,the natures of the contrary-ions and the natures of the same-electronic-inos have a few influential forces on the characteristic values,The temperature increasing makes the gelling reaction fast.

Control al doping Compromiso de Colombia

Directory of Open Access Journals (Sweden)

Claudia Prieto

2015-06-01

Full Text Available Este documento da a conocer la importante noticia de la aprobación, por parte del Comité Olímpico Internacional (COl, de un laboratorio colombiano, para el control al doping, a la vez que aprovecha la oportunidad para ampliar alguna información sobre este tema.

La ineficiencia tributaria en las provincias argentinas: el impuesto sobre los ingresos brutos

Directory of Open Access Journals (Sweden)

Dario Alejandro Rossignolo

2017-01-01

Full Text Available La organización tributaria federal de la Argentina prevé concurrencia en las fuentes de imposición para la imposición indirecta. En este trabajo se hará referencia al impuesto sobre los Ingresos Brutos, principal fuente de recaudación provincial. En consonancia con el IVA nacional, ambos son tributos generales sobre los consumos, adicionándole al tributo provincial la característica de afectar la producción por ser un tributo en cascada. El propósito es el de intentar identificar si una provincia se encuentra limitada en la recaudación impositiva por una baja capacidad de generar recursos o por un bajo esfuerzo en la explotación de la capacidad tributaria existente para financiar el gasto público.

Sol-gel dip coating of yttria-stabilized tetragonal zirconia dental ceramic by aluminosilicate nanocomposite as a novel technique to improve the bonding of veneering porcelain.

Science.gov (United States)

Madani, Azamsadat; Nakhaei, Mohammadreza; Karami, Parisa; Rajabzadeh, Ghadir; Salehi, Sahar; Bagheri, Hossein

2016-01-01

The aim of this in vitro study was to evaluate the effect of silica and aluminosilicate nanocomposite coating of zirconia-based dental ceramic by a sol-gel dip-coating technique on the bond strength of veneering porcelain to the yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in vitro. Thirty Y-TZP blocks (10 mm ×10 mm ×3 mm) were prepared and were assigned to four experimental groups (n=10/group): C, without any further surface treatment as the control group; S, sandblasted using 110 μm alumina powder; Si, silica sol dip coating + calcination; and Si/Al, aluminosilicate sol dip coating + calcination. After preparing Y-TZP samples, a 3 mm thick layer of the recommended porcelain was fired on the coated Y-TZP surface. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analysis were used to characterize the coating and the nature of the bonding between the coating and zirconia. To examine the zirconia-porcelain bond strength, a microtensile bond strength (μTBS) approach was chosen. FT-IR study showed the formation of silica and aluminosilicate materials. XRD pattern showed the formation of new phases consisting of Si, Al, and Zr in coated samples. SEM showed the formation of a uniform coating on Y-TZP samples. Maximum μTBS values were obtained in aluminosilicate samples, which were significantly increased compared to control and sandblasted groups (P=0.013 and Pcoating can be considered as a convenient, less expensive reliable method for improving the bond strength between dental Y-TZP ceramics and veneering porcelain.

Magnetic field dependence observed by 27 Al NMR of species contained in alumina colloidal dispersions

International Nuclear Information System (INIS)

Morgado Junior, Edisson; Menezes, Sonia M.C.; San Gil, Rosane

1995-01-01

The behaviour of some aluminium species front a magnetic field have been investigated by 27 Al NMR analysis, this method was used for characterization of an octahedric aluminium specie from sols prepared by bohemite acid peptization. X-ray diffraction data have identified the mineral structure. The results have been shown and discussed, and NMR spectra were also presented and studied. Concluding this work, the nature of a colloidal specie of alumina was clarified through the dependence research of magnetic field by 27 Al NMR

Synthesis of hybrid chitosan/calcium aluminosilicate using a sol-gel method for optical applications

Energy Technology Data Exchange (ETDEWEB)

Elnahrawy, Amany Mohamed [Department of Solid State, Physics Division, National Research Center (NRC), Giza 12622, Cairo (Egypt); Kim, Yong Soo, E-mail: yskim2@ulsan.ac.kr [Department of Physics and Energy Harvest-Storage Research Center (EHSRC), University of Ulsan, Ulsan 44610 (Korea, Republic of); Ali, Ahmed I., E-mail: Ahmed_ali_2010@helwan.edu.eg [Department of Physics and Energy Harvest-Storage Research Center (EHSRC), University of Ulsan, Ulsan 44610 (Korea, Republic of); Basic Science Department, Faculty of Industrial Education & Technology, Helwan University, Cairo 11281 (Egypt)

2016-08-15

Hybrid chitosan (CS)/calcium aluminosilicate nanocomposites thin films and membranes were prepared using a sol–gel method with three different concentrations of Al{sub 2}O{sub 3} (5, 7 and 10 mol. %). The prepared nanocomposites were characterized by transmission electron microscopy, X-ray diffraction and Fourier Transform Infrared spectroscopy. The optical properties of the prepared samples were analyzed by UV/Vis spectrophotometry and photoluminescence (PL) spectroscopy. The optical parameters revealed an increase in both the refractive index and band gap of the nanocomposites with increasing Al concentration. In addition, the PL spectra revealed a blue shift that was consistent with an increase in the optical band gap. These results suggest that CS/calcium aluminosilicate in two different forms can be a good candidate for optical sensors applications. - Highlights: • We show a large specific surface area of hybrid CS/calcium aluminosilicate thin films and membranes using sol-gel method. • Inorganic SiO{sub 2}-based phase are perfectly embedded onto chitosan matrix has a reliable stability. • CS/calcium aluminosilicate could be usable for optical sensors, planar waveguide, and bio-sensing.

Etat Du Magnesium Dans Quelques Sols Sales Du Sud Et Du ...

African Journals Online (AJOL)

étude a été réalisée sur 86 échantillons de sols provenant du Centre et du Sud de l´Irak. L\\'expérimentation a consisté, d´une part, à calculer les différents sels dominants dans les sols salés par la méthode de combinaison hypothétique et, ...

Physical properties and heterojunction device demonstration of aluminum-doped ZnO thin films synthesized at room ambient via sol-gel method

Energy Technology Data Exchange (ETDEWEB)

Karaagac, Hakan, E-mail: hkaraagac@ucdavis.edu [Department of Electrical and Computer Engineering, University of California at Davis, Davis, CA 95616 (United States); Yengel, Emre; Saif Islam, M. [Department of Electrical and Computer Engineering, University of California at Davis, Davis, CA 95616 (United States)

2012-04-25

Highlights: Black-Right-Pointing-Pointer Undoped and Al doped ZnO (AZO) thin films were successfully prepared using sol-gel technique. Black-Right-Pointing-Pointer Structural analysis has revealed that Al doping has a significant influence on preferential orientation. Black-Right-Pointing-Pointer It has been observed that wrinkles forms on the surface of films when annealed with a fast heat ramp up rate. Black-Right-Pointing-Pointer Optical analysis has revealed that that the band gap energy of ZnO thin film increases with increasing Al doping concentration. Black-Right-Pointing-Pointer The lowest resistivity is observed for 1% Al ZnO thin film, which is 2.2 Multiplication-Sign 10{sup -2} ({Omega} cm). - Abstract: ZnO and some of its ternary wide-bandgap alloys offer interesting opportunities for designing materials with tunable band gaps, strong piezoresistivity and controlled electrical conductance with high optical transparency. Synthesizing these materials on arbitrary substrates using low-cost and unconventional techniques can help in integrating semiconductors with different physical, electrical, and optical characteristics on a single substrate for heterogeneous integration of multifunctional devices. Here we report the successful synthesis of aluminum (Al) doped ZnO (AZO) thin films on soda-lime glass, silicon and fluorine doped tin oxide (FTO) pre-coated glass substrates by using sol-gel deposition method at ambient condition. X-ray diffraction (XRD) analysis revealed that varying degree of Al doping significantly impacts the crystal orientation, semiconductor bandgap and optical transparency of the film. Crystal structure of the film is also found to be strongly correlated to the characteristics of the substrate material. The impact of heating rate during post annealing process is studied and optimized in order to improve the surface morphology of the deposited films. Optical characterizations have revealed that bandgap energy of AZO films can be tuned

Morphology and the isoelectric point of nanosized aqueous ceria sols

International Nuclear Information System (INIS)

Gulicovski, Jelena J.; Bračko, Ines; Milonjić, Slobodan K.

2014-01-01

Ceria sols were synthesized by a forced hydrolysis method using cerium sulphate or cerium nitrate as precursors. High-resolution TEM was used to determine the microstructure and particle size of CeO 2 . A polycrystalline structure of ceria sols with crystallite sizes of 4.4 and 8.6 nm was obtained. The particles had a well-defined polyhedral shape. Direct bandgaps for ceria nanoparticles were 2.80 and 3.31 eV, respectively. The isoelectric point, pH iep , of ceria sols in KNO 3 solutions was investigated. The isoelectric point of ceria was found to be pH iep  = 7.6 ± 0.2. The obtained results indicate that the isoelectric point in the presence of SO 4 2− ions shifts to lower pH value. The particle size of ceria increases with pH, reaching the maximum value at pH iep as the result of agglomeration . - Highlights: • Ceria sols with cubic phase nanoparticles have been successfully synthesized. • The isoelectric point of ceria oxide in KNO 3 solutions was p Hiep  = 7.6 ± 0.2. • The specific adsorption of SO 4 2− ions causes a shift in IEP to lower pH (pH iep  = 6.7). • The correlation between IEP and the maximum diameter of particles was observed

Hydroxyapatite, fluor-hydroxyapatite and fluorapatite produced via the sol-gel method. Optimisation, characterisation and rheology.

Science.gov (United States)

Tredwin, Christopher J; Young, Anne M; Georgiou, George; Shin, Song-Hee; Kim, Hae-Won; Knowles, Jonathan C

2013-02-01

Currently, most titanium implant coatings are made using hydroxyapatite and a plasma spraying technique. There are however limitations associated with plasma spraying processes including poor adherence, high porosity and cost. An alternative method utilising the sol-gel technique offers many potential advantages but is currently lacking research data for this application. It was the objective of this study to characterise and optimise the production of Hydroxyapatite (HA), fluorhydroxyapatite (FHA) and fluorapatite (FA) using a sol-gel technique and assess the rheological properties of these materials. HA, FHA and FA were synthesised by a sol-gel method. Calcium nitrate and triethylphosphite were used as precursors under an ethanol-water based solution. Different amounts of ammonium fluoride (NH4F) were incorporated for the preparation of the sol-gel derived FHA and FA. Optimisation of the chemistry and subsequent characterisation of the sol-gel derived materials was carried out using X-ray Diffraction (XRD) and Differential Thermal Analysis (DTA). Rheology of the sol-gels was investigated using a viscometer and contact angle measurement. A protocol was established that allowed synthesis of HA, FHA and FA that were at least 99% phase pure. The more fluoride incorporated into the apatite structure; the lower the crystallisation temperature, the smaller the unit cell size (changes in the a-axis), the higher the viscosity and contact angle of the sol-gel derived apatite. A technique has been developed for the production of HA, FHA and FA by the sol-gel technique. Increasing fluoride substitution in the apatite structure alters the potential coating properties. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Spray pyrolysis synthesis of γ-Al_2O_3 supported metal and metal phosphide catalysts and their activity in the hydrodeoxygenation of a bio-oil model compound

International Nuclear Information System (INIS)

Ly, Hoang Vu; Im, Kyungmin; Go, Youngchae; Galiwango, Emmanuel; Kim, Seung-Soo; Kim, Jinsoo; Choi, Jae Hyung; Woo, Hee Chul

2016-01-01

Highlights: • Spherical γ-Al_2O_3 supported metal and metal phosphide catalysts were synthesized by spray pyrolysis method. • Hydrodeoxygenation (HDO) of 2-furyl methyl ketone (FMK) was conducted using metal/metal phosphide catalysts. • FMK was converted into 2-allyl furan and methyl cyclohexane. • The highest FMK conversion of 83% was achieved over 10 wt% Ni/γ-Al_2O_3 catalysts at reaction temperature of 400 °C. - Abstract: In this study, spherical γ-Al_2O_3 supported metal and metal phosphide (Ni, Co, Ni_2P and CoP) catalysts were successfully prepared by combining sol-gel and spray pyrolysis methods. First boehmite sol was prepared based on the Yoldas process and then the corresponding metal salts were added to the sol at the desired concentration, followed by spray pyrolysis of the mixed solution. As the well-mixed solution was transformed to spherical γ-Al_2O_3 supported metal and metal phosphide catalysts during spray pyrolysis process, the metal species were uniformly distributed in the mesoporous γ-Al_2O_3 supports. The product catalysts were investigated under different conditions for hydrodeoxygenation of bio-oil model compound, 2-furyl methyl ketone (FMK), which is the main component of the bio-oil product from pyrolysis of Saccharina japonica. Among the investigated catalysts, the 10 wt% Ni/γ-Al_2O_3 catalyst after calcination at 800 °C showed the highest FMK conversion of 83.02% at the reaction temperature of 400 °C. The gas and liquid products were analyzed by gas chromatography (GC) with TCD/FID detectors and GC–MS, respectively, to determine the product compositions.

Scratch resistance of SiO2 and SiO2 - ZrO2 sol-gel coatings on glass-ceramic obtained by sintering

International Nuclear Information System (INIS)

Soares, V. O.; Soares, P.; Peitl, O.; Zanotto, E. D.; Duran, A.; Castro, Y.

2013-01-01

The sol-gel process is widely used to obtain coatings on glass-ceramic substrates in order to improve the scratch and abrasion resistance, also providing a bright and homogeneous appearance of a glaze avoiding expensive final polishing treatments. This paper describes the preparation of silica and silica / zirconia coatings by sol-gel method on Li 2 O-Al 2 O3-SiO 2 (LAS) glassceramic substrates produced by sintering. The coatings were deposited by dip-coating on LAS substrates and characterized by optical microscopy and spectral ellipsometry. On the other hand, hardness and elastic modulus, coefficient of friction and abrasion and scratch resistance of the coatings were determined and compared with the substrate properties. Coatings deposited on LAS glass-ceramic confere the substrate a bright and homogeneous aspect, similar to a glaze, improving the appearance and avoiding the final polishing. However these coatings do not increase the scratch resistance of the substrate only equaling the properties of the glass-ceramic. (Author)

Sol-Gel Material-Enabled Electro-Optic Polymer Modulators

Science.gov (United States)

Himmelhuber, Roland; Norwood, Robert A.; Enami, Yasufumi; Peyghambarian, Nasser

2015-01-01

Sol-gels are an important material class, as they provide easy modification of material properties, good processability and are easy to synthesize. In general, an electro-optic (EO) modulator transforms an electrical signal into an optical signal. The incoming electrical signal is most commonly information encoded in a voltage change. This voltage change is then transformed into either a phase change or an intensity change in the light signal. The less voltage needed to drive the modulator and the lower the optical loss, the higher the link gain and, therefore, the better the performance of the modulator. In this review, we will show how sol-gels can be used to enhance the performance of electro-optic modulators by allowing for designs with low optical loss, increased poling efficiency and manipulation of the electric field used for driving the modulator. The optical loss is influenced by the propagation loss in the device, as well as the losses occurring during fiber coupling in and out of the device. In both cases, the use of sol-gel materials can be beneficial due to the wide range of available refractive indices and low optical attenuation. The influence of material properties and synthesis conditions on the device performance will be discussed. PMID:26225971

Sol-gel synthesis of lanthanum-gallate-based ceramic coatings

International Nuclear Information System (INIS)

Golubko, N.V.; Kaleva, G.M.; Roginskaya, Yu.E.; Politova, E.D.

2007-01-01

Phase-pure (La 0.9 Sr 0.1 )(Ga 0.7 Fe 0.3 )O 3-y and (Sr 1.8 La 0.2 )(GaFe)O 5.1 solid solutions with the perovskite and brownmillerite structures have been prepared from salt solutions by sol-gel processing at temperatures from 570 to 870 K. Ceramic coatings up to 100 μm in thickness have been produced by applying suspensions of the sol-gel powders to various substrates. The structure and microstructure of the ceramic coatings have been studied by X-ray diffraction and scanning electron microscopy [ru

Fiber damage during the consolidation of PVD Ti-6Al-4V coated NEXTEL 610 trademark alumina fibers

International Nuclear Information System (INIS)

Warren, J.; Elzey, D.M.; Wadley, H.N.G.

1995-01-01

Titanium matrix composites reinforced with sol-gel synthesized α-alumina fiber tows have attracted interest as a potentially low cost continuous fiber reinforced metal matrix composite system. The authors have conducted a detailed investigation of fiber damage during high temperature consolidation of PVD Ti-6Al-4V metallized sol-gel alumina fiber tows. Using both hot isostatic pressing and interrupted vacuum hot press consolidation cycles, the two principal mechanisms of fiber damage have been experimentally identified to be microbending/fracture and fiber matrix reaction. A time dependent micromechanics model incorporating the evolving geometry and mechanical properties of both the fibers and matrix has been formulated to simulate the fiber bending/failure mechanism in a representative unit cell and explore the effect of fiber strength loss due to reaction with the matrix. This model has been used to design a process cycle that minimizes damage by exploiting the enhanced superplastic deformation of the initially nanocrystalline PVD Ti-6Al-4V matrix