Interaction between two adjacent grounded sources in frequency domain semi-airborne electromagnetic survey.

Science.gov (United States)

Zhou, Haigen; Lin, Jun; Liu, Changsheng; Kang, Lili; Li, Gang; Zeng, Xinsen

2016-03-01

Multi-source and multi-frequency emission method can make full use of the valuable and short flight time in frequency domain semi-airborne electromagnetic (FSAEM) exploration, which has potential to investigate the deep earth structure in complex terrain region. Because several sources are adjacent in multi-source emission method, the interaction of different sources should be considered carefully. An equivalent circuit model of dual-source is established in this paper to assess the interaction between two individual sources, where the parameters are given with the typical values based on the practical instrument system and its application. By simulating the output current of two sources in different cases, the influence from the adjacent source is observed clearly. The current waveforms show that the mutual resistance causes the fluctuation and drift in another source and that the mutual inductance causes transient peaks. A field test with dual-source was conducted to certify the existence of interaction between adjacent sources. The simulation of output current also shows that current errors at low frequency are mainly caused by the mutual resistance while those at high frequency are mainly due to the mutual inductance. Increasing the distance between neighboring sources is a proposed measure to reduce the emission signal errors with designed ones. The feasible distance is discussed in the end. This study gives a useful guidance to lay multi sources to meet the requirement of measurement accuracy in FSAEM survey.

Inversion of Airborne Electromagnetic Data: Application to Oil Sands Exploration

Science.gov (United States)

Cristall, J.; Farquharson, C. G.; Oldenburg, D. W.

2004-05-01

. We provide an example that involves the interpretation of an airborne time-domain electromagnetic data-set from an oil sands exploration project in Alberta. The target is the layer that potentially contains oil sands. This layer is relatively resistive, with its resistivity increasing with increasing hydrocarbon content, and is sandwiched between two more conductive layers. This is quite different from the classical electromagnetic geophysics scenario of looking for a conductive mineral deposit in resistive shield rocks. However, inverting the data enabled the depth, thickness and resistivity of the target layer to be well determined. As a consequence, it is concluded that airborne electromagnetic surveys, when combined with inversion procedures, can be a very cost-effective way of mapping even fairly subtle conductivity variations over large areas.

Airborne electromagnetic data levelling using principal component analysis based on flight line difference

Science.gov (United States)

Zhang, Qiong; Peng, Cong; Lu, Yiming; Wang, Hao; Zhu, Kaiguang

2018-04-01

A novel technique is developed to level airborne geophysical data using principal component analysis based on flight line difference. In the paper, flight line difference is introduced to enhance the features of levelling error for airborne electromagnetic (AEM) data and improve the correlation between pseudo tie lines. Thus we conduct levelling to the flight line difference data instead of to the original AEM data directly. Pseudo tie lines are selected distributively cross profile direction, avoiding the anomalous regions. Since the levelling errors of selective pseudo tie lines show high correlations, principal component analysis is applied to extract the local levelling errors by low-order principal components reconstruction. Furthermore, we can obtain the levelling errors of original AEM data through inverse difference after spatial interpolation. This levelling method does not need to fly tie lines and design the levelling fitting function. The effectiveness of this method is demonstrated by the levelling results of survey data, comparing with the results from tie-line levelling and flight-line correlation levelling.

Performance metrics for state-of-the-art airborne magnetic and electromagnetic systems for mapping and detection of unexploded ordnance

Science.gov (United States)

Doll, William E.; Bell, David T.; Gamey, T. Jeffrey; Beard, Les P.; Sheehan, Jacob R.; Norton, Jeannemarie

2010-04-01

Over the past decade, notable progress has been made in the performance of airborne geophysical systems for mapping and detection of unexploded ordnance in terrestrial and shallow marine environments. For magnetometer systems, the most significant improvements include development of denser magnetometer arrays and vertical gradiometer configurations. In prototype analyses and recent Environmental Security Technology Certification Program (ESTCP) assessments using new production systems the greatest sensitivity has been achieved with a vertical gradiometer configuration, despite model-based survey design results which suggest that dense total-field arrays would be superior. As effective as magnetometer systems have proven to be at many sites, they are inadequate at sites where basalts and other ferrous geologic formations or soils produce anomalies that approach or exceed those of target ordnance items. Additionally, magnetometer systems are ineffective where detection of non-ferrous ordnance items is of primary concern. Recent completion of the Battelle TEM-8 airborne time-domain electromagnetic system represents the culmination of nearly nine years of assessment and development of airborne electromagnetic systems for UXO mapping and detection. A recent ESTCP demonstration of this system in New Mexico showed that it was able to detect 99% of blind-seeded ordnance items, 81mm and larger, and that it could be used to map in detail a bombing target on a basalt flow where previous airborne magnetometer surveys had failed. The probability of detection for the TEM-8 in the blind-seeded study area was better than that reported for a dense-array total-field magnetometer demonstration of the same blind-seeded site, and the TEM-8 system successfully detected these items with less than half as many anomaly picks as the dense-array total-field magnetometer system.

TESTING GROUND BASED GEOPHYSICAL TECHNIQUES TO REFINE ELECTROMAGNETIC SURVEYS NORTH OF THE 300 AREA, HANFORD, WASHINGTON

International Nuclear Information System (INIS)

Petersen, S.W.

2010-01-01

Airborne electromagnetic (AEM) surveys were flown during fiscal year (FY) 2008 within the 600 Area in an attempt to characterize the underlying subsurface and to aid in the closure and remediation design study goals for the 200-PO-1 Groundwater Operable Unit (OU). The rationale for using the AEM surveys was that airborne surveys can cover large areas rapidly at relatively low costs with minimal cultural impact, and observed geo-electrical anomalies could be correlated with important subsurface geologic and hydrogeologic features. Initial interpretation of the AEM surveys indicated a tenuous correlation with the underlying geology, from which several anomalous zones likely associated with channels/erosional features incised into the Ringold units were identified near the River Corridor. Preliminary modeling resulted in a slightly improved correlation but revealed that more information was required to constrain the modeling (SGW-39674, Airborne Electromagnetic Survey Report, 200-PO-1 Groundwater Operable Unit, 600 Area, Hanford Site). Both time-and frequency domain AEM surveys were collected with the densest coverage occurring adjacent to the Columbia River Corridor. Time domain surveys targeted deeper subsurface features (e.g., top-of-basalt) and were acquired using the HeliGEOTEM(reg s ign) system along north-south flight lines with a nominal 400 m (1,312 ft) spacing. The frequency domain RESOLVE system acquired electromagnetic (EM) data along tighter spaced (100 m (328 ft) and 200 m (656 ft)) north-south profiles in the eastern fifth of the 200-PO-1 Groundwater OU (immediately adjacent to the River Corridor). The overall goal of this study is to provide further quantification of the AEM survey results, using ground based geophysical methods, and to link results to the underlying geology and/or hydrogeology. Specific goals of this project are as follows: (1) Test ground based geophysical techniques for the efficacy in delineating underlying geology; (2) Use ground

TESTING GROUND BASED GEOPHYSICAL TECHNIQUES TO REFINE ELECTROMAGNETIC SURVEYS NORTH OF THE 300 AREA HANFORD WASHINGTON

Energy Technology Data Exchange (ETDEWEB)

PETERSEN SW

2010-12-02

Airborne electromagnetic (AEM) surveys were flown during fiscal year (FY) 2008 within the 600 Area in an attempt to characterize the underlying subsurface and to aid in the closure and remediation design study goals for the 200-PO-1 Groundwater Operable Unit (OU). The rationale for using the AEM surveys was that airborne surveys can cover large areas rapidly at relatively low costs with minimal cultural impact, and observed geo-electrical anomalies could be correlated with important subsurface geologic and hydrogeologic features. Initial interpretation of the AEM surveys indicated a tenuous correlation with the underlying geology, from which several anomalous zones likely associated with channels/erosional features incised into the Ringold units were identified near the River Corridor. Preliminary modeling resulted in a slightly improved correlation but revealed that more information was required to constrain the modeling (SGW-39674, Airborne Electromagnetic Survey Report, 200-PO-1 Groundwater Operable Unit, 600 Area, Hanford Site). Both time-and frequency domain AEM surveys were collected with the densest coverage occurring adjacent to the Columbia River Corridor. Time domain surveys targeted deeper subsurface features (e.g., top-of-basalt) and were acquired using the HeliGEOTEM{reg_sign} system along north-south flight lines with a nominal 400 m (1,312 ft) spacing. The frequency domain RESOLVE system acquired electromagnetic (EM) data along tighter spaced (100 m [328 ft] and 200 m [656 ft]) north-south profiles in the eastern fifth of the 200-PO-1 Groundwater OU (immediately adjacent to the River Corridor). The overall goal of this study is to provide further quantification of the AEM survey results, using ground based geophysical methods, and to link results to the underlying geology and/or hydrogeology. Specific goals of this project are as follows: (1) Test ground based geophysical techniques for the efficacy in delineating underlying geology; (2) Use ground

2.5D Inversion Algorithm of Frequency-Domain Airborne Electromagnetics with Topography

Directory of Open Access Journals (Sweden)

Jianjun Xi

2016-01-01

Full Text Available We presented a 2.5D inversion algorithm with topography for frequency-domain airborne electromagnetic data. The forward modeling is based on edge finite element method and uses the irregular hexahedron to adapt the topography. The electric and magnetic fields are split into primary (background and secondary (scattered field to eliminate the source singularity. For the multisources of frequency-domain airborne electromagnetic method, we use the large-scale sparse matrix parallel shared memory direct solver PARDISO to solve the linear system of equations efficiently. The inversion algorithm is based on Gauss-Newton method, which has the efficient convergence rate. The Jacobian matrix is calculated by “adjoint forward modelling” efficiently. The synthetic inversion examples indicated that our proposed method is correct and effective. Furthermore, ignoring the topography effect can lead to incorrect results and interpretations.

Survey result of airborne electromagnetic survey in the Hachimantai Sumikawa landslide area; Hachimantai Sumikawa jisuberi ni okeru kuchu denjiho chosa kekka

Energy Technology Data Exchange (ETDEWEB)

Konishi, N; Nakamura, N; Miyamoto, T [Nippon Engineering Consultant Co. Ltd., Tokyo (Japan)

1997-10-22

For the study of a landslide that occurred at Hachimantai Sumikawa, Akita Prefecture, an airborne electromagnetic survey is conducted for the examination of the relationship between the spot of landslide and solfataric clay (bluish gray clay). The location is a cap block type structure with a Neogene green tuff overlain by accumulated lava flow, where hot water is very active. The system used in this study is capable of measurement across a very wide frequency range, and measurements are made simultaneously at five frequencies of 220Hz, 1100Hz, 5500Hz, 27,500Hz, and 137,500Hz, these frequencies meaning depth levels 5m-70m explored. It is found that the spot of landslide matches a region where resistivity is so low as to be not higher than 10ohm/m. It is also found, in the resistivity cross section analysis for the middle part of the spot of landslide, that the mass of soil that moved on the upper part of the spot is relatively high in resistivity while the part below the slide surface is low in resistivity. There is agreement between the results reported above and the results of on-site investigations. 4 refs., 6 figs.

Airborne and ground-based transient electromagnetic mapping of groundwater salinity in the Machile–Zambezi Basin, southwestern Zambia

DEFF Research Database (Denmark)

Chongo, Mkhuzo; Vest Christiansen, Anders; Tembo, Alice

2015-01-01

The geological and morphological evolution of the Kalahari Basin of Southern Africa has given rise to a complex hydrogeological regime that is affected by water quality issues. Among these concerns is the occurrence of saline groundwater. Airborne and ground-based electromagnetic surveying...... of a low-resistivity (below 13 Ωm) valley that extends southwestwards into the Makgadikgadi salt pans. The electrical resistivity distribution is indicative of a full graben related to the Okavango–Linyati Fault system as a result of propagation of the East African Rift Valley System into Southern Africa...

Airborne electromagnetics data interactive visualisation and exploratory data analysis using Cloud technologies

Science.gov (United States)

Golodoniuc, P.; Davis, A. C.; Klump, J. F.

2017-12-01

Electromagnetic exploration techniques are extensively used for remote detection and measurement of subsurface electrical conductivity structures for a variety of geophysical applications such as mineral exploration and groundwater detection. The Electromagnetic Applications group in the Mineral Resources business unit of CSIRO heavily relies upon the use of airborne electromagnetic (AEM) data for the development of new exploration methods. AEM data, which are often originally acquired for green- or brown-fields exploration for minerals, can be re-used for groundwater resource detection in the near-surface. This makes AEM data potentially useful beyond their initial purpose for decades into the future. Increasingly, AEM data are also used as a primary mapping tool for groundwater resources. With surveys ranging from under 1000 km to tens of thousands of km in total length, AEM data are spatially and temporally dense. Sounding stations are often sampled every 0.2 seconds, with about 30-50 measurements taken at each site, resulting in a spacing of measurements along the flight lines of approximately 20­-50 metres. This means that typical AEM surveys can easily have on the order of millions of individual stations, with tens of millions of measurements. AEM data needs to be examined for data quality before it can be inverted into conductivity-depth information. Data, which is gathered in survey transects or lines, is examined both along the line, in a plan view and for the transient decay of the electromagnetic signal of individual stations before noise artefacts can be removed. The complexity of the data, its size and dimensionality require efficient tools that support interactive visual data analysis and allows easy navigation through the dataset. A suite of numerical algorithms for data quality assurance facilitates this process through efficient visualisations and data quality metrics. The extensible architecture of the toolkit allows application of custom

Geoid of Nepal from airborne gravity survey

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Einarsson, Indriði

2011-01-01

An airborne gravity survey of Nepal was carried out December 2010 in a cooperation between DTU-Space, Nepal Survey Department, and NGA, USA. The entire country was flown with survey lines spaced 6 nm with a King Air aircraft, with a varying flight altitude from 4 to 10 km. The survey operations...... as well as recent GPS-heights of Mt. Everest. The new airborne data also provide an independent validation of GOCE gravity field results at the local ~100 km resolution scale....

Applying airborne electromagnetics in 3D stochastic geohydrological modelling for determining groundwater protection

NARCIS (Netherlands)

Gunnink, J.L.; Siemon, B.

2015-01-01

Airborne electromagnetic (AEM) measurements provide information regarding the electrical properties of the subsurface for large spatial coverage in a limited time. In mapping and modelling for geological and geohydrological purposes, electrical properties (e.g. resistivity) need to be converted to

Preliminary report on geophysics ground follow-up of the 1977 airborne survey in the Wadi Bidah District, Kingdom of Saudi Arabia

Science.gov (United States)

Flanigan, V.J.; Wynn, J.C.; Worl, R.G.; Smith, C.W.

1981-01-01

Reconnaissance geologic and geochemical sampling was made during the 1978 field season at most of the 50 or so electromagnetic anomalies detected in the 1977 airborne electromagnetic (AEM) survey of the Wadi Bidah district. These Phase 1 studies also included reconnaissance geophysical traverses of nine of the AEM conductors. In addition the AEM anomalies were classified on the basis of this reconnaissance work into a list of priority targets for use in economic studies, and six AEM anomalies were selected for further studies.

Geological Mapping of Sabah, Malaysia, Using Airborne Gravity Survey

DEFF Research Database (Denmark)

Fauzi Nordin, Ahmad; Jamil, Hassan; Noor Isa, Mohd

2016-01-01

Airborne gravimetry is an effective tool for mapping local gravity fields using a combination of airborne sensors, aircraft and positioning systems. It is suitable for gravity surveys over difficult terrains and areas mixed with land and ocean. This paper describes the geological mapping of Sabah...... using airborne gravity surveys. Airborne gravity data over land areas of Sabah has been combined with the marine airborne gravity data to provide a seamless land-to-sea gravity field coverage in order to produce the geological mapping. Free-air and Bouguer anomaly maps (density 2.67 g/cm3) have been...... derived from the airborne data both as simple ad-hoc plots (at aircraft altitude), and as final plots from the downward continued airborne data, processed as part of the geoids determination. Data are gridded at 0.025 degree spacing which is about 2.7 km and the data resolution of the filtered airborne...

Integrated application of the database for airborne geophysical survey achievement information

International Nuclear Information System (INIS)

Ji Zengxian; Zhang Junwei

2006-01-01

The paper briefly introduces the database of information for airborne geophysical survey achievements. This database was developed on the platform of Microsoft Windows System with the technical methods of Visual C++ 6.0 and MapGIS. It is an information management system concerning airborne geophysical surveying achievements with perfect functions in graphic display, graphic cutting and output, query of data, printing of documents and reports, maintenance of database, etc. All information of airborne geophysical survey achievements in nuclear industry from 1972 to 2003 was embedded in. Based on regional geological map and Meso-Cenozoic basin map, the detailed statistical information of each airborne survey area, each airborne radioactive anomalous point and high field point can be presented visually by combining geological or basin research result. The successful development of this system will provide a fairly good base and platform for management of archives and data of airborne geophysical survey achievements in nuclear industry. (authors)

Remote sensing, airborne radiometric survey and aeromagnetic survey data processing and analysis

International Nuclear Information System (INIS)

Dong Xiuzhen; Liu Dechang; Ye Fawang; Xuan Yanxiu

2009-01-01

Taking remote sensing data, airborne radiometric data and aero magnetic survey data as an example, the authors elaborate about basic thinking of remote sensing data processing methods, spectral feature analysis and adopted processing methods, also explore the remote sensing data combining with the processing of airborne radiometric survey and aero magnetic survey data, and analyze geological significance of processed image. It is not only useful for geological environment research and uranium prospecting in the study area, but also reference to applications in another area. (authors)

Helicopter electromagnetic and magnetic geophysical survey data, Swedeburg and Sprague study areas, eastern Nebraska, May 2009

Science.gov (United States)

Smith, B.D.; Abraham, J.D.; Cannia, J.C.; Minsley, B.J.; Ball, L.B.; Steele, G.V.; Deszcz-Pan, M.

2011-01-01

This report is a release of digital data from a helicopter electromagnetic and magnetic survey conducted by Fugro Airborne Surveys in areas of eastern Nebraska as part of a joint hydrologic study by the Lower Platte North and Lower Platte South Natural Resources Districts, and the U.S. Geological Survey. The survey flight lines covered 1,418.6 line km (882 line mile). The survey was flown from April 22 to May 2, 2009. The objective of the contracted survey was to improve the understanding of the relation between surface water and groundwater systems critical to developing groundwater models used in management programs for water resources. The electromagnetic equipment consisted of six different coil-pair orientations that measured resistivity at separate frequencies from about 400 hertz to about 140,000 hertz. The electromagnetic data were converted to georeferenced electrical resistivity grids and maps for each frequency that represent different approximate depths of investigation for each survey area. The electrical resistivity data were input into a numerical inversion to estimate resistivity variations with depth. In addition to the electromagnetic data, total field magnetic data and digital elevation data were collected. Data released in this report consist of flight line data, digital grids, digital databases of the inverted electrical resistivity with depth, and digital maps of the apparent resistivity and total magnetic field. The range of subsurface investigation is comparable to the depth of shallow aquifers. The survey areas, Swedeburg and Sprague, were chosen based on results from test flights in 2007 in eastern Nebraska and needs of local water managers. The geophysical and hydrologic information from U.S. Geological Survey studies are being used by resource managers to develop groundwater resource plans for the area.

Fundamental study on airborne electromagnetic survey using grounded source; Chihyo source gata kuchu denji tansa no kisoteki kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Mogi, T; Fujimitsu, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tanaka, Y [Kyoto University, Kyoto (Japan). Faculty of Science; Jomori, N [Chiba Electronics Research Institute, Chiba (Japan); Morikawa, T [Dowa Engineering Co. Ltd., Okayama (Japan); Kusunoki, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-05-27

With an objective to develop an airborne electromagnetic survey method for greater depths achievable of exploration, a discussion was given on an exploration method of a type in which a transmitting device is placed on the ground to receive signals in an atmosphere. A prototype exploration apparatus is mounted with a fluxgate magnetometer, an attitude meter, a GPS, and a battery. This exploration apparatus is suspended on a 30 meter long rope from a helicopter to perform the exploration. Two flight tests on this apparatus were carried out in the Unzen area, Nagasaki Prefecture and the Motomiya area, Wakayama Prefecture. The ground source was extended to a distance of 1.5 km, and a current of about 20 A was flown with a quiescent wave having four-second cycles. The helicopter flew nearly horizontally at a ground speed of about 50 km, a flight altitude of 450 m above sea level, and a terrain clearances of 100 to 400 m. The obtained data had variations in correspondence with changes in roll and pitch angles, whereas the variation of about 5000 nT was reduced to about 1000 nT as a result of correction. It was not possible, however, to correct completely the variation with short cycles, requiring further discussions on frequency characteristics of the magnetometer. 6 figs., 1 tab.

The alpine Swiss-French airborne gravity survey

Science.gov (United States)

Verdun, Jérôme; Klingelé, Emile E.; Bayer, Roger; Cocard, Marc; Geiger, Alain; Kahle, Hans-Gert

2003-01-01

In February 1998, a regional-scale, airborne gravity survey was carried out over the French Occidental Alps within the framework of the GéoFrance 3-D research program.The survey consisted of 18 NS and 16 EW oriented lines with a spacing of 10 and 20 km respectively, covering the whole of the Western French Alps (total area: 50 000 km2; total distance of lines flown: 10 000 km). The equipment was mounted in a medium-size aircraft (DeHavilland Twin Otter) flowing at a constant altitude of 5100 m a.s.l, and at a mean ground speed of about 280 km h-1. Gravity was measured using a LaCoste & Romberg relative, air/sea gravimeter (type SA) mounted on a laser gyro stabilized platform. Data from 5 GPS antennae located on fuselage and wings and 7 ground-based GPS reference stations were used to determine position and aircraft induced accelerations.The gravimeter passband was derived by comparing the vertical accelerations provided by the gravimeter with those estimated from the GPS positions. This comparison showed that the gravimeter is not sensitive to very short wavelength aircraft accelerations, and therefore a simplified formulation for computing airborne gravity measurements was developed. The intermediate and short wavelength, non-gravitational accelerations were eliminated by means of digital, exponential low-pass filters (cut-off wavelength: 16 km). An important issue in airborne gravimetry is the reliability of the airborne gravity surveys when compared to ground surveys. In our studied area, the differences between the airborne-acquired Bouguer anomaly and the ground upward-continued Bouguer anomaly of the Alps shows a good agreement: the rms of these differences is equal to 7.68 mGal for a spatial resolution of 8 km. However, in some areas with rugged topography, the amplitudes of those differences have a striking correlation with the topography. We then argue that the choice of an appropriate density (reduction by a factor of 10 per cent) for computing the

Geophex airborne unmanned survey system

International Nuclear Information System (INIS)

Won, I.J.; Taylor, D.W.A.

1995-01-01

The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This nonintrusive system will provide open-quotes stand-offclose quotes capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. This system permits two operators to rapidly conduct geophysical characterization of hazardous environmental sites. During a survey, the operators remain remote from, but within visual distance, of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak anomalies can be detected

Numerical results for near surface time domain electromagnetic exploration: a full waveform approach

Science.gov (United States)

Sun, H.; Li, K.; Li, X., Sr.; Liu, Y., Sr.; Wen, J., Sr.

2015-12-01

Time domain or Transient electromagnetic (TEM) survey including types with airborne, semi-airborne and ground play important roles in applicants such as geological surveys, ground water/aquifer assess [Meju et al., 2000; Cox et al., 2010], metal ore exploration [Yang and Oldenburg, 2012], prediction of water bearing structures in tunnels [Xue et al., 2007; Sun et al., 2012], UXO exploration [Pasion et al., 2007; Gasperikova et al., 2009] etc. The common practice is introducing a current into a transmitting (Tx) loop and acquire the induced electromagnetic field after the current is cut off [Zhdanov and Keller, 1994]. The current waveforms are different depending on instruments. Rectangle is the most widely used excitation current source especially in ground TEM. Triangle and half sine are commonly used in airborne and semi-airborne TEM investigation. In most instruments, only the off time responses are acquired and used in later analysis and data inversion. Very few airborne instruments acquire the on time and off time responses together. Although these systems acquire the on time data, they usually do not use them in the interpretation.This abstract shows a novel full waveform time domain electromagnetic method and our recent modeling results. The benefits comes from our new algorithm in modeling full waveform time domain electromagnetic problems. We introduced the current density into the Maxwell's equation as the transmitting source. This approach allows arbitrary waveforms, such as triangle, half-sine, trapezoidal waves or scatter record from equipment, being used in modeling. Here, we simulate the establishing and induced diffusion process of the electromagnetic field in the earth. The traditional time domain electromagnetic with pure secondary fields can also be extracted from our modeling results. The real time responses excited by a loop source can be calculated using the algorithm. We analyze the full time gates responses of homogeneous half space and two

A comparison of helicopter-borne electromagnetics in frequency- and time-domain at the Cuxhaven valley in Northern Germany

DEFF Research Database (Denmark)

Steuner, Annika; Siemon, Bernhard; Auken, Esben

2010-01-01

Two different airborne electromagnetic methods were applied in the same area: the frequency-domain helicopter-borne electromagnetic (HEM)system operated by the Federal Institute for Geosciences and Natural Resources, Germany, and the time-domain SkyTEM system of theHydroGeophysics Group at the Un......Two different airborne electromagnetic methods were applied in the same area: the frequency-domain helicopter-borne electromagnetic (HEM)system operated by the Federal Institute for Geosciences and Natural Resources, Germany, and the time-domain SkyTEM system of theHydroGeophysics Group...... at the University of Aarhus, Denmark. For verification of and comparison with the airborne methods, ground-basedtransient electromagnetics and 2-D resistivity surveying were carried out. The target of investigation was the Cuxhaven valley in NorthernGermany, which is a significant local groundwater reservoir...

Geostatistical analysis of the relationship between airborne electromagnetic data and borehole lithological data

DEFF Research Database (Denmark)

Barfod, Adrian; Møller, Ingelise; Christiansen, Anders Vest

2015-01-01

resistivity values, revealing different distribution functions for lithological categories. A very large and extensive dataset is available in Denmark through the national geophysical and borehole databases. These databases contain all geophysical and borehole data in Denmark and covers a large part of its......We present a large-scale study of the relationship between dense airborne SkyTEM resistivity data and sparse lithological borehole data. Airborne electromagnetic (AEM) data contains information about subsurface geology and hydrologic properties; however extracting this information is not trivial....... Today, geophysical data is used in combination with borehole data to create detailed geological models of the subsurface. The overall statistical relationship is, however, not widely known. The objective of this study is to develop a method for understanding the relationship between petrophysical...

Voxel inversion of airborne electromagnetic data for improved model integration

Science.gov (United States)

Fiandaca, Gianluca; Auken, Esben; Kirkegaard, Casper; Vest Christiansen, Anders

2014-05-01

Inversion of electromagnetic data has migrated from single site interpretations to inversions including entire surveys using spatial constraints to obtain geologically reasonable results. Though, the model space is usually linked to the actual observation points. For airborne electromagnetic (AEM) surveys the spatial discretization of the model space reflects the flight lines. On the contrary, geological and groundwater models most often refer to a regular voxel grid, not correlated to the geophysical model space, and the geophysical information has to be relocated for integration in (hydro)geological models. We have developed a new geophysical inversion algorithm working directly in a voxel grid disconnected from the actual measuring points, which then allows for informing directly geological/hydrogeological models. The new voxel model space defines the soil properties (like resistivity) on a set of nodes, and the distribution of the soil properties is computed everywhere by means of an interpolation function (e.g. inverse distance or kriging). Given this definition of the voxel model space, the 1D forward responses of the AEM data are computed as follows: 1) a 1D model subdivision, in terms of model thicknesses, is defined for each 1D data set, creating "virtual" layers. 2) the "virtual" 1D models at the sounding positions are finalized by interpolating the soil properties (the resistivity) in the center of the "virtual" layers. 3) the forward response is computed in 1D for each "virtual" model. We tested the new inversion scheme on an AEM survey carried out with the SkyTEM system close to Odder, in Denmark. The survey comprises 106054 dual mode AEM soundings, and covers an area of approximately 13 km X 16 km. The voxel inversion was carried out on a structured grid of 260 X 325 X 29 xyz nodes (50 m xy spacing), for a total of 2450500 inversion parameters. A classical spatially constrained inversion (SCI) was carried out on the same data set, using 106054

Geophex airborne unmanned survey system

Energy Technology Data Exchange (ETDEWEB)

Won, I.J.; Taylor, D.W.A.

1995-03-01

The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This nonintrusive system will provide {open_quotes}stand-off{close_quotes} capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. This system permits two operators to rapidly conduct geophysical characterization of hazardous environmental sites. During a survey, the operators remain remote from, but within visual distance, of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak anomalies can be detected.

A comparison of helicopter-borne electromagnetic systems for hydrogeologic studies

Science.gov (United States)

Bedrosian, Paul A.; Schamper, Cyril; Auken, Esben

2016-01-01

The increased application of airborne electromagnetic surveys to hydrogeological studies is driving a demand for data that can consistently be inverted for accurate subsurface resistivity structure from the near surface to depths of several hundred metres. We present an evaluation of three commercial airborne electromagnetic systems over two test blocks in western Nebraska, USA. The selected test blocks are representative of shallow and deep alluvial aquifer systems with low groundwater salinity and an electrically conductive base of aquifer. The aquifer units show significant lithologic heterogeneity and include both modern and ancient river systems. We compared the various data sets to one another and inverted resistivity models to borehole lithology and to ground geophysical models. We find distinct differences among the airborne electromagnetic systems as regards the spatial resolution of models, the depth of investigation, and the ability to recover near-surface resistivity variations. We further identify systematic biases in some data sets, which we attribute to incomplete or inexact calibration or compensation procedures.

Evaluation of airborne thermal, magnetic, and electromagnetic characterization technologies

Energy Technology Data Exchange (ETDEWEB)

Josten, N.E.

1992-03-01

The identification of Buried Structures (IBS) or Aerial Surveillance Project was initiated by the US Department of Energy (DOE) Office of Technology Development to demonstrate airborne methods for locating and identifying buried waste and ordnance at the Idaho National Engineering Laboratory (INEL). Two technologies were demonstrated: (a) a thermal infrared imaging system built by Martin Marietta Missile Systems and (b) a magnetic and electromagnetic (EM) geophysical surveying system operated by EBASCO Environmental. The thermal system detects small differences in ground temperature caused by uneven heating and cooling of the ground by the sun. Waste materials on the ground can be detected when the temperature of the waste is different than the background temperature. The geophysical system uses conventional magnetic and EM sensors. These sensors detect disturbances caused by magnetic or conductive waste and naturally occurring magnetic or conductive features of subsurface soils and rock. Both systems are deployed by helicopter. Data were collected at four INEL sites. Tests at the Naval Ordnance Disposal Area (NODA) were made to evaluate capabilities for detecting ordnance on the ground surface. Tests at the Cold Simulated Waste Demonstration Pit were made to evaluate capabilities for detecting buried waste at a controlled site, where the location and depth of buried materials are known. Tests at the Subsurface Disposal Area and Stationary Low-Power Reactor-1 burial area were made to evaluate capabilities for characterizing hazardous waste at sites that are typical of DOE buried waste sites nationwide.

Evaluation of airborne thermal, magnetic, and electromagnetic characterization technologies

International Nuclear Information System (INIS)

Josten, N.E.

1992-03-01

The identification of Buried Structures (IBS) or Aerial Surveillance Project was initiated by the US Department of Energy (DOE) Office of Technology Development to demonstrate airborne methods for locating and identifying buried waste and ordnance at the Idaho National Engineering Laboratory (INEL). Two technologies were demonstrated: (a) a thermal infrared imaging system built by Martin Marietta Missile Systems and (b) a magnetic and electromagnetic (EM) geophysical surveying system operated by EBASCO Environmental. The thermal system detects small differences in ground temperature caused by uneven heating and cooling of the ground by the sun. Waste materials on the ground can be detected when the temperature of the waste is different than the background temperature. The geophysical system uses conventional magnetic and EM sensors. These sensors detect disturbances caused by magnetic or conductive waste and naturally occurring magnetic or conductive features of subsurface soils and rock. Both systems are deployed by helicopter. Data were collected at four INEL sites. Tests at the Naval Ordnance Disposal Area (NODA) were made to evaluate capabilities for detecting ordnance on the ground surface. Tests at the Cold Simulated Waste Demonstration Pit were made to evaluate capabilities for detecting buried waste at a controlled site, where the location and depth of buried materials are known. Tests at the Subsurface Disposal Area and Stationary Low-Power Reactor-1 burial area were made to evaluate capabilities for characterizing hazardous waste at sites that are typical of DOE buried waste sites nationwide

Feasibility study of geophysical survey in Uruguay 07.05 - 02.06.1987

International Nuclear Information System (INIS)

Eberle, D.

1987-01-01

The aim of this report has been carried out an airborne magnetic and radiometric survey that would be followed by an interpretation stage to delineate and area of increased mineral potential where an airborne electromagnetic survey might be held in further stage.

Simultaneous inversion of airborne electromagnetic data for resistivity and magnetic permeability

International Nuclear Information System (INIS)

Beard, L.P.; Nyquist, J.E.

1998-01-01

Where the magnetic permeability of rock or soil exceeds that of free space, the effect on airborne electromagnetic systems is to produce a frequency-independent shift in the in-phase response of the system while altering the quadrature response only slightly. The magnitude of the in-phase shift increases as (1) the relative magnetic permeability is increased, (2) the amount of magnetic material is increased, and (3) the airborne sensor gets nearer the earth's surface. Over resistive, magnetic ground, the shift may be evinced by negative in-phase measurements at low frequencies; but over more conductive ground, the same shift may go unnoticed because of the large positive in-phase response. If the airborne sensor is flown at low levels, the magnitude of the shift may be large enough to affect automatic inversion routines that do not take this shift into account, producing inaccurate estimated resistivities, usually overestimates. However, layered-earth inversion algorithms that incorporate magnetic permeability as an additional inversion parameter may improve the resistivity estimates. The authors demonstrate this improvement using data collected over hazardous waste sites near Oak Ridge, Tennessee, USA. Using resistivity inversion without magnetic permeability, the waste sites are almost invisible to the sensors. When magnetic permeability is included as an inversion parameter, the sites are detected, both by improved resistivity estimates and by estimated magnetic permeability

Airborne campaigns for CryoSat pre-launch calibration and validation

DEFF Research Database (Denmark)

Hvidegaard, Sine Munk; Forsberg, René; Skourup, Henriette

2010-01-01

From 2003 to 2008 DTU Space together with ESA and several international partners carried out airborne and ground field campaigns in preparation for CryoSat validation; called CryoVEx: CryoSat Validation Experiments covering the main ice caps in Greenland, Canada and Svalbard and sea ice in the Ar......From 2003 to 2008 DTU Space together with ESA and several international partners carried out airborne and ground field campaigns in preparation for CryoSat validation; called CryoVEx: CryoSat Validation Experiments covering the main ice caps in Greenland, Canada and Svalbard and sea ice...... in the Arctic Ocean. The main goal of the airborne surveys was to acquire coincident scanning laser and CryoSat type radar elevation measurements of the surface; either sea ice or land ice. Selected lines have been surveyed along with detailed mapping of validation sites coordinated with insitu field work...... and helicopter electromagnetic surveying. This paper summarises the pre-launch campaigns and presents some of the result from the coincident measurement from airborne and ground observations....

New Inversion and Interpretation of Public-Domain Electromagnetic Survey Data from Selected Areas in Alaska

Science.gov (United States)

Smith, B. D.; Kass, A.; Saltus, R. W.; Minsley, B. J.; Deszcz-Pan, M.; Bloss, B. R.; Burns, L. E.

2013-12-01

Public-domain airborne geophysical surveys (combined electromagnetics and magnetics), mostly collected for and released by the State of Alaska, Division of Geological and Geophysical Surveys (DGGS), are a unique and valuable resource for both geologic interpretation and geophysical methods development. A new joint effort by the US Geological Survey (USGS) and the DGGS aims to add value to these data through the application of novel advanced inversion methods and through innovative and intuitive display of data: maps, profiles, voxel-based models, and displays of estimated inversion quality and confidence. Our goal is to make these data even more valuable for interpretation of geologic frameworks, geotechnical studies, and cryosphere studies, by producing robust estimates of subsurface resistivity that can be used by non-geophysicists. The available datasets, which are available in the public domain, include 39 frequency-domain electromagnetic datasets collected since 1993, and continue to grow with 5 more data releases pending in 2013. The majority of these datasets were flown for mineral resource purposes, with one survey designed for infrastructure analysis. In addition, several USGS datasets are included in this study. The USGS has recently developed new inversion methodologies for airborne EM data and have begun to apply these and other new techniques to the available datasets. These include a trans-dimensional Markov Chain Monte Carlo technique, laterally-constrained regularized inversions, and deterministic inversions which include calibration factors as a free parameter. Incorporation of the magnetic data as an additional constraining dataset has also improved the inversion results. Processing has been completed in several areas, including Fortymile and the Alaska Highway surveys, and continues in others such as the Styx River and Nome surveys. Utilizing these new techniques, we provide models beyond the apparent resistivity maps supplied by the original

Airborne Multi-Spectral Minefield Survey

Science.gov (United States)

2005-05-01

Swedish Defence Research Agency), GEOSPACE (Austria), GTD ( Ingenieria de Sistemas y Software Industrial, Spain), IMEC (Ineruniversity MicroElectronic...RTO-MP-SET-092 18 - 1 UNCLASSIFIED/UNLIMITED UNCLASSIFIED/UNLIMITED Airborne Multi-Spectral Minefield Survey Dirk-Jan de Lange, Eric den...actions is the severe lack of baseline information. To respond to this in a rapid way, cost-efficient data acquisition methods are a key issue. de

Successful application of frequency-domain airborne electromagnetic system with a grounded electric source

Science.gov (United States)

Kang, L.; Lin, J.; Liu, C.; Zhou, H.; Ren, T.; Yao, Y.

2017-12-01

A new frequency-domain AEM system with a grounded electric source, which was called ground-airborne frequency-domain electromagnetic (GAFEM) system, was proposed to extend penetration depth without compromising the resolution and detection efficiency. In GAFEM system, an electric source was placed on the ground to enlarge the strength of response signals. UVA was chosen as aircraft to reduce interaction noise and improve its ability to adapt to complex terrain. Multi-source and multi-frequency emission method has been researched and applied to improve the efficiency of GAFEM system. 2n pseudorandom sequence was introduced as transmitting waveform, to ensure resolution and detection efficiency. Inversion-procedure based on full-space apparent resistivity formula was built to realize GAFEM method and extend the survey area to non-far field. Based on GAFEM system, two application was conducted in Changchun, China, to map the deep conductive structure. As shown in the results of this exploration, GAFEM system shows its effectiveness to conductive structure, obtaining a depth of about 1km with a source-receiver distance of over 6km. And it shows the same level of resolution with CSAMT method with an over 10 times of efficiency. This extended a range of important applications where the terrain is too complex to be accessed or large penetration depth is required in a large survey area.

Airborne geophysical radon hazard mapping

International Nuclear Information System (INIS)

Walker, P.

1993-01-01

Shales containing uranium pose a radon health hazard even when covered by several meters of overburden. Such an alum shale in southern Norway has been mapped with a joint helicopter borne electromagnetic (HEM) and radiometric survey. Results are compared with ground spectrometer, radon emanometer and radon gas measurements in dwellings, and a model to predict radon gas concentrations from the airborne data is developed. Since the shale is conductive, combining the HEM data with the radiometric channel allows the shale to be mapped with greater reliability than if the radiometric channel were used alone. Radiometrically more active areas which do not pose a radon gas hazard can thus be separated from the shales which do. The ground follow-up work consisted of spectrometer and radon emanometer measurements over a uranium anomaly coinciding with a conductor. The correlation between the airborne uranium channel, the ground uranium channel and emanometry is extremely good, indicating that airborne geophysics can, in this case, be used to predict areas having a high radon potential. Contingency tables comparing both radon exhalation and concentration in dwellings with the airborne uranium data show a strong relationship exists between exhalation and the airborne data and while a relationship between concentration and the airborne data is present, but weaker

Aerial Transient Electromagnetic Surveys of Alluvial Aquifers in Rural Watersheds of Arizona

Science.gov (United States)

Pool, D. R.; Callegary, J. B.; Groom, R. W.

2006-12-01

Development in rural areas of Arizona has led the State of Arizona (Arizona Department of Water Resources), in cooperation with the Arizona Water Science Center of the U.S. Geological Survey, to sponsor investigations of the hydrogeologic framework of several alluvial-basin aquifers. An efficient method for mapping the aquifer extent and lithology was needed due to sparse subsurface information. Aerial Transient Electro-Magnetic (ATEM) methods were selected because they can be used to quickly survey large areas and with a great depth of investigation. Both helicopter and fixed-wing ATEM methods are available. A fixed-wing method (GEOTEM) was selected because of the potential for a depth of investigation of 300 m or more and because previous surveys indicated the method is useful in alluvial basins in southeastern Arizona. About 2,900 km of data along flight lines were surveyed across five alluvial basins, including the Middle San Pedro and Willcox Basins in southeastern Arizona, and Detrital, Hualapai, and Sacramento Basins in northwestern Arizona. Data initially were analyzed by the contractor (FUGRO Airborne Surveys) to produce conductivity-depth-transforms, which approximate the general subsurface electrical-property distribution along profiles. Physically based two-dimensional physical models of the profile data were then developed by PetRos- Eikon by using EMIGMA software. Hydrologically important lithologies can have different electrical properties. Several types of crystalline and sedimentary rocks generally are poor aquifers that have low porosity and high electrical resistivity. Good alluvial aquifers of sand and gravel generally have an intermediate electrical resistivity. Poor aquifer materials, such as silt and clay, and areas of poor quality water have low electrical resistivity values. Several types of control data were available to constrain the models including drill logs, electrical logs, water levels , and water quality information from wells; and

An efficient hybrid scheme for fast and accurate inversion of airborne transient electromagnetic data

DEFF Research Database (Denmark)

Christiansen, Anders Vest; Auken, Esben; Kirkegaard, Casper

2016-01-01

Airborne transient electromagnetic (TEM) methods target a range of applications that all rely on analysis of extremely large datasets, but with widely varying requirements with regard to accuracy and computing time. Certain applications have larger intrinsic tolerances with regard to modelling...... inaccuracy, and there can be varying degrees of tolerance throughout different phases of interpretation. It is thus desirable to be able to tune a custom balance between accuracy and compute time when modelling of airborne datasets. This balance, however, is not necessarily easy to obtain in practice....... Typically, a significant reduction in computational time can only be obtained by moving to a much simpler physical description of the system, e.g. by employing a simpler forward model. This will often lead to a significant loss of accuracy, without an indication of computational precision. We demonstrate...

Helicopter electromagnetic and magnetic geophysical survey data, portions of the North Platte and South Platte Natural Resources Districts, western Nebraska, May 2009

Science.gov (United States)

Smith, B.D.; Abraham, J.D.; Cannia, J.C.; Minsley, B.J.; Deszcz-Pan, M.; Ball, L.B.

2010-01-01

This report is a release of digital data from a helicopter electromagnetic and magnetic survey that was conducted during June 2009 in areas of western Nebraska as part of a joint hydrologic study by the North Platte Natural Resource District (NRD), South Platte NRD, and U.S. Geological Survey (USGS). Flight lines for the survey totaled 937 line kilometers (582 line miles). The objective of the contracted survey, conducted by Fugro Airborne, Ltd., is to improve the understanding of the relation between surface-water and groundwater systems critical to developing groundwater models used in management programs for water resources. A unique aspect of the survey is the flight line layout. One set of flight lines was flown in a zig-zag pattern extending along the length of the previously collected airborne data. The success of this survey design depended on a well-understood regional hydrogeologic framework and model developed by the Cooperative Hydrologic Study of the Platte River Basin and the airborne geophysical data collected in 2008. Resistivity variations along lines could be related to this framework. In addition to these lines, more traditional surveys consisting of parallel flight lines, separated by about 400 meters were carried out for three blocks in the North Platte NRD, the South Platte NRD and in the area of Crescent Lakes. These surveys helped to establish the spatial variations of the resistivity of hydrostratigraphic units. An additional survey was flown over the Crescent Lake area. The objective of this survey, funded by the USGS Office of Groundwater, was to map shallow hydrogeologic features of the southwestern part of the Sand Hills that contain a mix of fresh to saline lakes.

A multi-scale permafrost investigation along the Alaska Highway Corridor based on airborne electromagnetic and auxiliary geophysical data

Science.gov (United States)

Minsley, B. J.; Kass, M. A.; Bloss, B.; Pastick, N.; Panda, S. K.; Smith, B. D.; Abraham, J. D.; Burns, L. E.

2012-12-01

More than 8000 square kilometers of airborne electromagnetic (AEM) data were acquired along the Alaska Highway Corridor in 2005-2006 by the Alaska Department of Natural Resources Division of Geological and Geophysical Surveys. Because this large AEM dataset covers diverse geologic and permafrost settings, it is an excellent testbed for studying the electrical geophysical response from a wide range of subsurface conditions. These data have been used in several recent investigations of geology, permafrost, and infrastructure along the highway corridor. In this study, we build on existing interpretations of permafrost features by re-inverting the AEM data using traditional least squares inversion techniques as well as recently developed stochastic methods aimed at quantifying uncertainty in geophysical data. Ground-based geophysical measurements, including time-domain electromagnetic soundings, surface nuclear magnetic resonance soundings, and shallow frequency-domain electromagnetic profiles, have also been acquired to help validate and extend the AEM interpretations. Here, we focus on the integration of different types of data to yield an improved characterization of permafrost, including: methods to discriminate between geologic and thermal controls on resistivity; identifying relationships between shallow resistivity and active layer thickness by incorporating auxiliary remote sensing data and ground-based measurements; quantifying apparent slope-aspect-resistivity relationships, where south-facing slopes appear less resistive than north-facing slopes within similar geologic settings; and investigating an observed decrease in resistivity beneath several areas associated with recent fires.

Survey of subsurface geophysical exploration technologies adaptable to an airborne platform

International Nuclear Information System (INIS)

Taylor, K.A.

1992-12-01

This report has been prepared by the US Department of Energy (DOE) as part of a Research Development Demonstration Testing and Evaluation (RDDT ampersand E) project by EG ampersand G Energy Measurement's (EG ampersand G/EM) Remote Sensing Laboratory. It examines geophysical detection techniques which may be used in Environmental Restoration/Waste Management (ER/WM) surveys to locate buried waste, waste containers, potential waste migratory paths, and aquifer depths. Because of the Remote Sensing Laboratory's unique survey capabilities, only those technologies which have been adapted or are capable of being adapted to an airborne platform were studied. This survey describes several of the available subsurface survey technologies and discusses the basic capabilities of each: the target detectability, required geologic conditions, and associated survey methods. Because the airborne capabilities of these survey techniques have not been fully developed, the chapters deal mostly with the ground-based capabilities of each of the technologies, with reference made to the airborne capabilities where applicable. The information about each survey technique came from various contractors whose companies employ these specific technologies. EG ampersand G/EM cannot guarantee or verify the accuracy of the contractor information; however, the data given is an indication of the technologies that are available

Analysis of Alabama Airborne Gravity at Three Altitudes: Expected Accuracy and Spatial Resolution from a Future Tibetan Airborne Gravity Survey

Directory of Open Access Journals (Sweden)

Chi-Hsun Huang

2013-01-01

Full Text Available In situ airborne gravity data at altitudes of 11, 6.3, and 1.7 km over a smooth area of Alabama are used to assess gravity accuracy and errors in upward and downward continuations. Analysis of the Alabama free-air anomaly gravity data at crossover points at the three altitudes suggests 1 - 2 mgal accuracy for the dataset. Gravity data at each altitude are then expanded into local 3D Fourier series, to prepare for continuation. This Fourier representation results in continuation errors at few-mgal level in Alabama, even in the extreme case of downward continuation from 11 km to sea level. The result in Alabama inspires an airborne gravity survey over the rough, inaccessible terrain of Tibet. Similar investigations as in Alabama are made in Tibet using EGM08-derived airborne gravity data at flight altitudes of 10, 5, and 0 km. Bouguer anomalies at the 10-km altitude preserve the major tectonic features of Tibet. Downward continuation errors increase with terrain roughness, but the survey can enhance local tectonic features. This study highlights the value of a future Tibetan airborne gravity survey and points out the expected gravity accuracy and spatial resolution from this survey.

Merging airborne and carborne radiometric data for surveying the Deir Az-Zor area, Syria

International Nuclear Information System (INIS)

Jubeli, Y.M.; Aissa, M.; Al-Hent, R.

1997-01-01

To complete the radiometric map of Syria, and to estimate the natural background radiation levels for environmental monitoring, a carborne survey was undertaken over the Deir Az-Zor area. This area was not covered by a previous airborne survey, except for peripheral regions in the south and west. To complete the radiometric map, results of the carborne and airborne surveys had to be merged. This paper presents the merging procedure which was used after normalizing the two data sets to match each other. No anomalies suitable for radioelement exploration were found. However, the overall radiometric maps resulting from the present work were consistent with the maps of the areas covered by the airborne survey. (author)

Airborne Gravimetry Survey for the Marine Area of the United Arab Emirates

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Alshamsi, Adel

2012-01-01

The Military Survey Department (MSD) of the United Arab Emirates (UAE) undertook an airborne gravity survey project for the marine area of the country in 2009, especially to strengthen the marine and coastal geoid in the near-shore regions. For the airborne gravity survey, 5 km spacing coast...... flight speed of 170 knots and a typical flight elevation of 900-1500 m, depending on weather conditions and topography. Gravity was measured with a ZLS-modified LaCoste and Romberg gravimeter (S-99), augmented with a Honeywell strap-down inertial navigation system unit. The estimated accuracy...

Modeling Marine Electromagnetic Survey with Radial Basis Function Networks

Directory of Open Access Journals (Sweden)

Agus Arif

2014-11-01

Full Text Available A marine electromagnetic survey is an engineering endeavour to discover the location and dimension of a hydrocarbon layer under an ocean floor. In this kind of survey, an array of electric and magnetic receivers are located on the sea floor and record the scattered, refracted and reflected electromagnetic wave, which has been transmitted by an electric dipole antenna towed by a vessel. The data recorded in receivers must be processed and further analysed to estimate the hydrocarbon location and dimension. To conduct those analyses successfuly, a radial basis function (RBF network could be employed to become a forward model of the input-output relationship of the data from a marine electromagnetic survey. This type of neural networks is working based on distances between its inputs and predetermined centres of some basis functions. A previous research had been conducted to model the same marine electromagnetic survey using another type of neural networks, which is a multi layer perceptron (MLP network. By comparing their validation and training performances (mean-squared errors and correlation coefficients, it is concluded that, in this case, the MLP network is comparatively better than the RBF network[1].[1] This manuscript is an extended version of our previous paper, entitled Radial Basis Function Networks for Modeling Marine Electromagnetic Survey, which had been presented on 2011 International Conference on Electrical Engineering and Informatics, 17-19 July 2011, Bandung, Indonesia.

Helicopter Electromagnetic and Magnetic Geophysical Survey Data for Portions of the North Platte River and Lodgepole Creek, Nebraska, June 2008

Science.gov (United States)

Smith, Bruce D.; Abraham, Jared D.; Cannia, James C.; Hill, Patricia

2009-01-01

This report is a release of digital data from a helicopter electromagnetic and magnetic survey that was conducted during June 2008 in areas of western Nebraska as part of a joint hydrologic study by the North Platte Natural Resource District, South Platte Natural Resource District, and U.S. Geological Survey. The objective of the contracted survey, conducted by Fugro Airborne, Ltd., was to improve the understanding of the relationship between surface water and groundwater systems critical to developing groundwater models used in management programs for water resources. The survey covered 1,375 line km (854 line mi). A unique aspect of this survey is the flight line layout. One set of flight lines were flown paralleling each side of the east-west trending North Platte River and Lodgepole Creek. The survey also included widely separated (10 km) perpendicular north-south lines. The success of this survey design depended on a well understood regional hydrogeologic framework and model developed by the Cooperative Hydrologic Study of the Platte River Basin. Resistivity variations along lines could be related to this framework. In addition to these lines, more traditional surveys consisting of parallel flight lines separated by about 270 m were carried out for one block in each of the drainages. These surveys helped to establish the spatial variations of the resistivity of hydrostratigraphic units. The electromagnetic equipment consisted of six different coil-pair orientations that measured resistivity at separated frequencies from about 400 Hz to about 140,000 Hz. The electromagnetic data along flight lines were converted to electrical resistivity. The resulting line data were converted to geo-referenced grids and maps which are included with this report. In addition to the electromagnetic data, total field magnetic data and digital elevation data were collected. Data released in this report consist of data along flight lines, digital grids, and digital maps of the

Airborne geophysical survey, Wind River Basin area, Wyoming

International Nuclear Information System (INIS)

1974-01-01

Results are reported of AEC-sponsored, high sensitivity, reconnaisance airborne gamma-ray survey of the Wind River Basin area, Wyoming. The objective of the survey was to define those areas showing surface indications of a generally higher uranium content (uraniferous provinces) and where detailed exploration for uranium would most likely be successful. For the data collection tasks, a TI high sensitivity gamma-ray system consisting of seven large-volume NaI detectors, two 400-channel analyzers, and ancillary geophysical and electronic equipment was used. Gamma-ray spectrometric data were processed to correct for variations in atmospheric and flight conditions and statistically evaluated to remove the effect of surface geologic variations. Data were then compared to regional geomorphic lineaments derived from ERTS-1 imagery. Aeromagnetic data were collected simultaneously with the airborne gamma-ray survey and interpreted in terms of regional structure. Ten major anomalous uranium areas and ten less strong anomalous areas were defined within the region surveyed. These anomalies and the known mining districts and uranium occurrences demonstrated good correlation with the ERTS lineaments. The basins were defined by the aeromagnetic data. It is suggested that gamma-ray spectrometer data be supplemented by both the ERTS and aeromagnetic data to best define the targets of greatest potential for further exploration. (U.S.)

Investigation of the potential for concealed base-metal mineralization at the Drenchwater Creek Zn-Pb-Ag occurrence, northern Alaska, using geology, reconnaissance geochemistry, and airborne electromagnetic geophysics

Science.gov (United States)

Graham, Garth E.; Deszcz-Pan, Maria; Abraham, Jared E.; Kelley, Karen D.

2011-01-01

In 2005, the U.S. Geological Survey, Bureau of Land Management, and State of Alaska cooperated on an investigation of the mineral potential of a southern part of the National Petroleum Reserve in Alaska, Howard Pass quadrangle, to provide background information for future land-use decisions. The investigation incorporated an airborne electromagnetic (EM) survey covering 1,500 mi2 (~3,900 km2), including flight lines directly over the Drenchwater Creek sediment-hosted Zn-Pb-Ag occurrence, the largest known base-metal occurrence in the survey area. Samples from the mineralized outcrop and rubblecrop contain metal concentrations that can exceed 11 percent Zn+Pb, with appreciable amounts of Ag. Soil samples with anomalous Pb concentrations are distributed near the sulfide-bearing outcrops and along a >2.5 km zone comprising mudstone, shale, and volcanic rocks of the Kuna Formation.

Ultrafine particles over Eastern Australia: an airborne survey

Directory of Open Access Journals (Sweden)

Wolfgang Junkermann

2015-04-01

Full Text Available Ultrafine particles (UFP in the atmosphere may have significant impacts on the regional water and radiation budgets through secondary effects on cloud microphysics. Yet, as these particles are invisible for current remote sensing techniques, knowledge about their three-dimensional distribution, source strengths and budgets is limited. Building on a 40-yr-old Australia-wide airborne survey which provides a reference case study of aerosol sources and budgets, this study presents results from a new airborne survey over Eastern Australia, northern New South Wales and Queensland. Observations identified apparent changes in the number and distribution of major anthropogenic aerosol sources since the early 1970s, which might relate to the simultaneously observed changes in rainfall patterns over eastern Queensland. Coal-fired power stations in the inland areas between Brisbane and Rockhampton were clearly identified as the major sources for ultrafine particulate matter. Sugar mills, smelters and shipping along the coast close to the Ports of Townsville and Rockhampton were comparable minor sources. Airborne Lagrangian plume studies were applied to investigate source strength and ageing properties within power station plumes. Significant changes observed, compared to the measurements in the 1970s, included a significant increase in the number concentration of UFP related to coal-fired power station emissions in the sparsely populated Queensland hinterland coincident with the area with the most pronounced reduction in rainfall.

Airborne gravity survey of Lincoln Sea and Wandel Sea, north Greenland

DEFF Research Database (Denmark)

Olesen, Arne Vestergaard; Forsberg, René; Keller, K.

2000-01-01

In June 1998 National Survey and Cadastre Denmark (KMS) carried out an airborne gravity survey over the Polar Sea to the north of Greenland. A Twin Otter from Greenlandair, equipped with autopilot and additional fuel tanks, was employed for the survey. A modified marine LaCoste & Romberg gravimet...

Advanced data processing of airborne electromagnetic data for imaging hidden conduit networks in the coastal karst plain of Tulum (Mexico)

International Nuclear Information System (INIS)

Schiller, A.; Schattauer, I.; Ottowitz, D.

2016-01-01

This study is part of a series of international research cooperations which commenced in 2007 and are still ongoing. The study area is located on the east coast of the Yucatan Peninsula, Mexico, and comprises the northern most part of the Sian Kaan biosphere reserve, a coastal wetland of international importance, as well as the city of Tulum in the state of Quintana Roo, and part of the second largest barrier reef in the world some 300 metres to one kilometre off shore. Two airborne surveys, conducted in 2007 and 2008 by the Geological Survey of Austria, covered an area of some 200 square kilometres, including the well-known Ox Bel Ha cave system, already mapped by exploration divers. In order to get additional ground truth data and input for the hydrological model, extended ground geophysical campaigns have been conducted an - nually. The first processing of the airborne electromagnetic (AEM) data revealed not only a clear signature from known caves but also the image of a vast, unexplored, hidden conduit network. However, lateral and depth resolution was limited due to measurement drift and noise as well the specific behaviour of the ap - plied inversion technique. Newly developed algorithms for processing AEM data and inversion results have improved the signal-to-noise ratio significantly and enabled the imaging of well defined structures in the underground. Therefore, the AEM method is now capable of quickly deliver crucial structural information of karst-water regimes in difficult accessible areas with unique depth information compared to previous studies. (Author)

Airborne VLF survey of Izu-Oshima volcano

Energy Technology Data Exchange (ETDEWEB)

Murakami, Yutaka; Yukutake, Takeshi

1988-05-17

Resistivity distribution in underground indicates anomaly in some cases due to volcanic activity, airborne VLF survey of Izu-Oshima volcano in whole area was carried out by measurement of the anomalous vertical magnetic field. The flight direction was determined with reference to both of the transmitter direction of the VLF waves and the running direction of the geologic formation. The flight altitude and the flight lines spacing were 100 m and 200 m respectively. Typical profiles of four lines of measurement were investigated. The resistivity anomalies were indicated corresponding to the position of known geologic fissure line, the lip of the caldera, the line of the craters and side volcanos. Several anomalous trends were detected by the contour drawing of the Fraser filter output. The detected results were as follow: new volcanos with the resistivity anomaly, the resistivity anomalies spread to the north-northwest from Goshinka jaya, the anomalies due to flowed lava, the anomalies by encroached water from the caldera wall, the effects from side volcanoes and so on. The resistivity anomalies by airborne VLF survey correspond to the known volcanic activities, and they are useful for elucidation of the underground volcanism. (6 figs, 4 refs)

Airborne geophysical survey of the catastrophic landslide at Stože, Log pod Mangrtom, as a test of an innovative approach for landslide mapping in steep alpine terrains

Directory of Open Access Journals (Sweden)

I. Baroň

2013-10-01

Full Text Available Airborne geophysics is a promising method for investigating landslides. Here we present a case study of multisensor airborne geophysical survey at the catastrophic landslide Stože near Log pod Mangrtom in Slovenia, which was conducted in the framework of the European FP7th Project "SafeLand". Based on the survey itself and achieved results, we discuss applicability, limits, and benefits and costs of the method for investigating landslides in steep alpine terrains. Despite of several operational constraints, the airborne electromagnetic survey of the area well presented the lithological pattern and water saturation. The high resistivity regions mostly indicated drained slope scree and landslide mass, drained and loosened material of the moraine deposit in the tension zone of the landslide with present cracks and cavities. The minima of the resistivity pattern were attributed to the outcrop of marls rich in clay, to water-saturated moraine deposit above impermeable marls in the tension zone, and to water-saturated porous alluvial gravel and landslide scree along the Koritnica River. The magnetic survey proved to be inapplicable for such a small and rough area. The Potassium and Thorium maps, on the other hand, both well identified the regions of tension inside the landslide zone, outcrops of marls and dolomite, clay-rich colluvium, weathered zones along a regional tectonic fault, and alluvial deposits and deposits of debris flows, and the minima of the 137Cs clearly revealed the zones of material removal due to recent mass movements.

Development of instrumentation for airborne radiometric surveys in the Atomic Minerals Division: Past, present, and future

International Nuclear Information System (INIS)

Sreehari, R.

1993-01-01

A high-sensitivity airborne gamma-ray spectrometric and magnetic survey system, using Na(Tl) detector volume of 50,000 cc for 4π and 4195 cc for 2π geometry applications, was designed, developed, and fabricated in 1978 and was flown for airborne surveys in various parts of India for over a decade. A compact complementary metal-oxide-semiconductor (CMOS) logic circuit based high-sensitivity airborne gamma-ray spectrometric and magnetic survey system with high noise-immunity using Na(Tl) detector volume of 50,000 cc for 4π and 12,500 cc for 2π geometry applications was developed and interfaced to an Inertial Navigation System in 1988. The system currently in use was flown extensively for airborne surveys in various parts of India for the Atomic Minerals Division, Oil and Natural Gas Commission, and Nuclear Power Corporation. The design aspects of the present system have been discussed. A microprocessor based DDAS and multichannel analysers, having on-line micro terminal and on-line corrections for Compton scatter, and background radiation to obtain corrected analog profiles for the spectrometric data, are currently under development. The design aspects of these units are described and evaluated for future high-sensitivity airborne gamma-ray spectrometric surveys with Nal(Tl) detector volumes similar to those of the present system. (author). 8 refs., 3 figs., 1 tab

Model structural uncertainty quantification and hydrogeophysical data integration using airborne electromagnetic data (Invited)

DEFF Research Database (Denmark)

Minsley, Burke; Christensen, Nikolaj Kruse; Christensen, Steen

of airborne electromagnetic (AEM) data to estimate large-scale model structural geometry, i.e. the spatial distribution of different lithological units based on assumed or estimated resistivity-lithology relationships, and the uncertainty in those structures given imperfect measurements. Geophysically derived...... estimates of model structural uncertainty are then combined with hydrologic observations to assess the impact of model structural error on hydrologic calibration and prediction errors. Using a synthetic numerical model, we describe a sequential hydrogeophysical approach that: (1) uses Bayesian Markov chain...... Monte Carlo (McMC) methods to produce a robust estimate of uncertainty in electrical resistivity parameter values, (2) combines geophysical parameter uncertainty estimates with borehole observations of lithology to produce probabilistic estimates of model structural uncertainty over the entire AEM...

Determining a pre-mining radiological baseline from historic airborne gamma surveys: A case study

International Nuclear Information System (INIS)

Bollhöfer, Andreas; Beraldo, Annamarie; Pfitzner, Kirrilly; Esparon, Andrew; Doering, Che

2014-01-01

Knowing the baseline level of radioactivity in areas naturally enriched in radionuclides is important in the uranium mining context to assess radiation doses to humans and the environment both during and after mining. This information is particularly useful in rehabilitation planning and developing closure criteria for uranium mines as only radiation doses additional to the natural background are usually considered ‘controllable’ for radiation protection purposes. In this case study we have tested whether the method of contemporary groundtruthing of a historic airborne gamma survey could be used to determine the pre-mining radiological conditions at the Ranger mine in northern Australia. The airborne gamma survey was flown in 1976 before mining started and groundtruthed using ground gamma dose rate measurements made between 2007 and 2009 at an undisturbed area naturally enriched in uranium (Anomaly 2) located nearby the Ranger mine. Measurements of 226 Ra soil activity concentration and 222 Rn exhalation flux density at Anomaly 2 were made concurrent with the ground gamma dose rate measurements. Algorithms were developed to upscale the ground gamma data to the same spatial resolution as the historic airborne gamma survey data using a geographic information system, allowing comparison of the datasets. Linear correlation models were developed to estimate the pre-mining gamma dose rates, 226 Ra soil activity concentrations, and 222 Rn exhalation flux densities at selected areas in the greater Ranger region. The modelled levels agreed with measurements made at the Ranger Orebodies 1 and 3 before mining started, and at environmental sites in the region. The conclusion is that our approach can be used to determine baseline radiation levels, and provide a benchmark for rehabilitation of uranium mines or industrial sites where historical airborne gamma survey data are available and an undisturbed radiological analogue exists to groundtruth the data. - Highlights: �

Modeling of airborne electromagnetic anomalies related to fractured bedrock and overburden

International Nuclear Information System (INIS)

Peltoniemi, M.; Baers, R.; Vaeisaenen, M.

1993-08-01

Responses of a multifrequency, multicoil airborne electromagnetic (AEM) system were modeled using numerical techniques. Special emphasis was given to poor, three-dimensional electrical conductors embedded both in the bedrock and in the overburden. The results cover vertical coaxial and horizontal coplanar configurations and three frequencies: 888 Hz, 7837 Hz and 51250 Hz. The models studied are signal conductors in free space, and single or multiple conductors embedded in a host rock of high but finite resistivity (5000 Wm) and overlain by a layer of overburden with finite resistivity and thickness. Two different types of computer software were used in the modelling: the free-space PLATE code, and the EM3D set of codes. Modeling results are given both as profiles and as charasteristic diagrams for the various coil configuration - conductor-model combinations. On the basis of the modeling results, limits of detectability for poor conductors have been determined. The study is a part of the preliminary site investigations for the radioactive waste disposal in Finnish bedrock

Helicopter electromagnetic and magnetic geophysical survey data, Hunton anticline, south-central Oklahoma

Science.gov (United States)

Smith, Bruce D.; Smith, David V.; Deszcz-Pan, Maryla; Blome, Charles D.; Hill, Patricia

2011-01-01

This report is a digital data release for multiple geophysical surveys conducted in the Hunton anticline area of south-central Oklahoma. The helicopter electromagnetic and magnetic surveys were flown on March 16–17, 2007, in four areas of the Hunton anticline in south-central Oklahoma. The objective of this project is to improve the understanding of the geohydrologic framework of the Arbuckle-Simpson aquifer. The electromagnetic sensor for the helicopter electromagnetic survey consisted of six different transmitter-receiver orientations that measured the earth's electrical response at six distinct frequencies from approximately 500 Hertz to approximately 115,000 Hertz. The electromagnetic measurements were converted to electrical resistivity values, which were gridded and plotted on georeferenced maps. The map from each frequency represents a different depth of investigation for each area. The range of subsurface investigation is comparable to the depth of shallow groundwater. The four areas selected for the helicopter electromagnetic study, blocks A–D, have different geologic and hydrologic settings. Geophysical and hydrologic information from U.S. Geological Survey studies are being used by modelers and resource managers to develop groundwater resource plans for the Arbuckle-Simpson aquifer.

Air sampling system for airborne surveys

International Nuclear Information System (INIS)

Jupiter, C.; Tipton, W.J.

1975-01-01

An air sampling system has been designed for installation on the Beechcraft King Air A-100 aircraft as a part of the Aerial Radiological Measuring System (ARMS). It is intended for both particle and whole gas sampling. The sampling probe is designed for isokinetic sampling and is mounted on a removable modified escape hatch cover, behind the co-pilot's seat, and extends about two feet forward of the hatch cover in the air stream lines. Directly behind the sampling probe inside the modified hatch cover is an expansion chamber, space for a 5-inch diameter filter paper cassette, and an optional four-stage cascade impactor for particle size distribution measurements. A pair of motors and blower pumps provide the necessary 0.5 atmosphere pressure across the type MSA 1106 B glass fiber filter paper to allow a flow rate of 50 cfm. The MSA 1106 B filter paper is designed to trap sub-micrometer particles with a high efficiency; it was chosen to enable a quantitative measurement of airborne radon daughters, one of the principal sources of background signals when radiological surveys are being performed. A venturi section and pressure gauges allow air flow rate measurements so that airborne contaminant concentrations may be quantified. A whole gas sampler capable of sampling a cubic meter of air is mounted inside the aircraft cabin. A nuclear counting system on board the aircraft provides capability for α, β and γ counting of filter paper samples. Design data are presented and types of survey missions which may be served by this system are described

Using Helicopter Electromagnetic Surveys to Identify Potential Hazards at Mine Waste Impoundments

Energy Technology Data Exchange (ETDEWEB)

Hammack, R.W.

2008-01-01

In July 2003, helicopter electromagnetic surveys were conducted at 14 coal waste impoundments in southern West Virginia. The purpose of the surveys was to detect conditions that could lead to impoundment failure either by structural failure of the embankment or by the flooding of adjacent or underlying mine works. Specifically, the surveys attempted to: 1) identify saturated zones within the mine waste, 2) delineate filtrate flow paths through the embankment or into adjacent strata and receiving streams, and 3) identify flooded mine workings underlying or adjacent to the waste impoundment. Data from the helicopter surveys were processed to generate conductivity/depth images. Conductivity/depth images were then spatially linked to georeferenced air photos or topographic maps for interpretation. Conductivity/depth images were found to provide a snapshot of the hydrologic conditions that exist within the impoundment. This information can be used to predict potential areas of failure within the embankment because of its ability to image the phreatic zone. Also, the electromagnetic survey can identify areas of unconsolidated slurry in the decant basin and beneath the embankment. Although shallow, flooded mineworks beneath the impoundment were identified by this survey, it cannot be assumed that electromagnetic surveys can detect all underlying mines. A preliminary evaluation of the data implies that helicopter electromagnetic surveys can provide a better understanding of the phreatic zone than the piezometer arrays that are typically used.

Structural Mapping Along the Central San Andreas Fault-zone Using Airborne Electromagnetics

Science.gov (United States)

Zamudio, K. D.; Bedrosian, P.; Ball, L. B.

2017-12-01

Investigations of active fault zones typically focus on either surface expressions or the associated seismogenic zones. However, the largely aseismic upper kilometer can hold significant insight into fault-zone architecture, strain partitioning, and fault-zone permeability. Geophysical imaging of the first kilometer provides a link between surface fault mapping and seismically-defined fault zones and is particularly important in geologically complex regions with limited surface exposure. Additionally, near surface imaging can provide insight into the impact of faulting on the hydrogeology of the critical zone. Airborne electromagnetic (AEM) methods offer a unique opportunity to collect a spatially-large, detailed dataset in a matter of days, and are used to constrain subsurface resistivity to depths of 500 meters or more. We present initial results from an AEM survey flown over a 60 kilometer long segment of the central San Andreas Fault (SAF). The survey is centered near Parkfield, California, the site of the SAFOD drillhole, which marks the transition between a creeping fault segment to the north and a locked zone to the south. Cross sections with a depth of investigation up to approximately 500 meters highlight the complex Tertiary and Mesozoic geology that is dismembered by the SAF system. Numerous fault-parallel structures are imaged across a more than 10 kilometer wide zone centered on the surface trace. Many of these features can be related to faults and folds within Plio-Miocene sedimentary rocks found on both sides of the fault. Northeast of the fault, rocks of the Mesozoic Franciscan and Great Valley complexes are extremely heterogeneous, with highly resistive volcanic rocks within a more conductive background. The upper 300 meters of a prominent fault-zone conductor, previously imaged to 1-3 kilometers depth by magnetotellurics, is restricted to a 20 kilometer long segment of the fault, but is up to 4 kilometers wide in places. Elevated fault

Construction of a groundwater-flow model for the Big Sioux Aquifer using airborne electromagnetic methods, Sioux Falls, South Dakota

Science.gov (United States)

Valder, Joshua F.; Delzer, Gregory C.; Carter, Janet M.; Smith, Bruce D.; Smith, David V.

2016-09-28

The city of Sioux Falls is the fastest growing community in South Dakota. In response to this continued growth and planning for future development, Sioux Falls requires a sustainable supply of municipal water. Planning and managing sustainable groundwater supplies requires a thorough understanding of local groundwater resources. The Big Sioux aquifer consists of glacial outwash sands and gravels and is hydraulically connected to the Big Sioux River, which provided about 90 percent of the city’s source-water production in 2015. Managing sustainable groundwater supplies also requires an understanding of groundwater availability. An effective mechanism to inform water management decisions is the development and utilization of a groundwater-flow model. A groundwater-flow model provides a quantitative framework for synthesizing field information and conceptualizing hydrogeologic processes. These groundwater-flow models can support decision making processes by mapping and characterizing the aquifer. Accordingly, the city of Sioux Falls partnered with the U.S. Geological Survey to construct a groundwater-flow model. Model inputs will include data from advanced geophysical techniques, specifically airborne electromagnetic methods.

Research on 3-D terrain correction methods of airborne gamma-ray spectrometry survey

International Nuclear Information System (INIS)

Liu Yanyang; Liu Qingcheng; Zhang Zhiyong

2008-01-01

The general method of height correction is not effectual in complex terrain during the process of explaining airborne gamma-ray spectrometry data, and the 2-D terrain correction method researched in recent years is just available for correction of section measured. A new method of 3-D sector terrain correction is studied. The ground radiator is divided into many small sector radiators by the method, then the irradiation rate is calculated in certain survey distance, and the total value of all small radiate sources is regarded as the irradiation rate of the ground radiator at certain point of aero- survey, and the correction coefficients of every point are calculated which then applied to correct to airborne gamma-ray spectrometry data. The method can achieve the forward calculation, inversion calculation and terrain correction for airborne gamma-ray spectrometry survey in complex topography by dividing the ground radiator into many small sectors. Other factors are considered such as the un- saturated degree of measure scope, uneven-radiator content on ground, and so on. The results of for- ward model and an example analysis show that the 3-D terrain correction method is proper and effectual. (authors)

Airborne geoid determination

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Bastos, L.

2000-01-01

Airborne geoid mapping techniques may provide the opportunity to improve the geoid over vast areas of the Earth, such as polar areas, tropical jungles and mountainous areas, and provide an accurate "seam-less" geoid model across most coastal regions. Determination of the geoid by airborne methods...... relies on the development of airborne gravimetry, which in turn is dependent on developments in kinematic GPS. Routine accuracy of airborne gravimetry are now at the 2 mGal level, which may translate into 5-10 cm geoid accuracy on regional scales. The error behaviour of airborne gravimetry is well......-suited for geoid determination, with high-frequency survey and downward continuation noise being offset by the low-pass gravity to geoid filtering operation. In the paper the basic principles of airborne geoid determination are outlined, and examples of results of recent airborne gravity and geoid surveys...

Joint Interpretation of Magnetotellurics and Airborne Electromagnetics in the Rathlin Basin, Northern Ireland

Science.gov (United States)

Delhaye, Robert; Rath, Volker; Jones, Alan G.; Reay, Derek; The Iretherm Team

2015-04-01

In this study we present results from geophysical investigation of the sedimentary Rathlin Basin in Northern Ireland in order to assess the potential for low-to-medium enthalpy geothermal aquifers within the porous Permian and Triassic sandstone groups. The area and groups were identified as a potential geothermal resource due to the presence of both an elevated geothermal gradient (observed in two deep boreholes onshore) and favourable hydraulic properties (measured on core samples in the offshore part of the basin). Previous seismic experiments were not able to fully characterise the sediments beneath the overlying flood basalt. Complementing these earlier results, magnetotelluric data were acquired on a grid of 56 sites across the north-eastern portion of the onshore Rathlin Basin, and an additional 12 sites on the nearby Rathlin Island, in order to image the thickness, depth, and lateral continuity of the target sediments. Analysis and 3D modelling, including the effects of the highly conducting ocean, has been successful in deriving a resistivity model that maps the variation in the top of the sediments (base of the basalts) and the truncation of the basin sediments against the Tow Valley Fault, and gives a reasonable estimate of the thickness of the sediment fill. However, the resulting models show significant effects from distortion caused by near-surface inhomogeneities in the responses that cannot be resolved using the given frequency range and site density. Fortunately, for the area of Rathlin Basin, airborne electromagnetic data from the TELLUS project (http://www.bgs.ac.uk/gsni/tellus/contact/index.html) are available. These data were measured at four frequencies between 0.9 kHz and 25 kHz in a verical-coplanar loop configuration, with the dipole axis in flight direction. The spatial sampling distance was less than 25 m, with about 200 m distance between flight lines. Survey altitudes vary between 56 m and 244 m. Thus, for the top ˜100 m penetrated by

Environmental airborn radioactivity survey around Burg El Arab Area, Western desert, Egypt

International Nuclear Information System (INIS)

Fouad, K.M.; Ammar, A.A.; Meleik, M.L.

1977-01-01

An environmental airborne radioactivity survey of approximately 250 square kilometres of Burg El Arab area was conducted by the Airborne Geophysical survey Division of the Geology and Raw Materials Department. The environmental levels of gamma radiation are measured so as to determine quickly the amount and extent of any possible future increase in radioactivity levels of the area by the proposed nuclear facility through normal operations or any accident that may occur. The aerial radiometric measurements were obtained by a continuously recording airborne scintillometer type RVS-1. installed in an Antonoff-2 aircraft, flying at an average speed of 170 Km/h, at a nominal ground clearance of 50 m. The survey was carried out along 84 parallel flight lines directed N-S, and spaced 250 m apart. The area is shown on the geological map as composed of four lithological units. The analysis of the data has proved that these units correspond to six distinct levels of characteristic radioactivity, as two of the lithological units could each be separated into two radioactivity levels on the basis of the radioactivity pattern. The six radiometric levels are, from north to south, beach limy sediments (15 to 101. and 97 to 191 cps), detrital limestone (201 to 354 cpt), saline lakes and salt deposits (262 to 444 cps), and alluvial deposits (307 to 308 and 412 to 742 cps)

Research progress in airborne surveys of terrestrial gamma radiation

International Nuclear Information System (INIS)

Burson, Z.G.

1974-01-01

Progress during the last few years in airborne surveys of terrestrial gamma radiation, i.e. in the measuring, recording, and interpreting of gamma ray signals in NaI(Tl) crystals, is discussed. Non-terrestrial background contributions have been accurately characterized. The feasibility of determining the water equivalent of snow cover by aerial survey techniques has been demonstrated. Repeat surveys over areas surrounding reactor sites can now be used to detect average differences of less than 1.0 μR/hr in terrestrial gamma radiation levels. New data acquisition and recording systems allow isotope concentrations and total inventories to be measured in spatial resolutions of a few hundred feet. Aerial survey data have been combined with population distribution data to obtain population exposure values from natural terrestrial gamma radiation around reactor sites

The use of airborne electromagnetic for efficient mapping of salt water intrusion and outflow to the sea

DEFF Research Database (Denmark)

Auken, Esben; Kirkegaard, Casper; Ribeiro, Joana

2010-01-01

Airborne electromagnetic (AEM) is an efficient tool for mapping groundwater resources in sedimentary environments. AEM delivers a very high data coverage and results in high-resolution electrical images of the subsurface. In particular the time domain methods (TEM) are well suited for mapping o0f...... not only the salt-fresh water boundary in the coastal zone, but also the mixing of fresh-salt-water on the seaside. Even freshwater layers under several meters of brackish water can be mapped. Sufficient depth of investigation is obtained by time domain methods as they have a significant higher transmitter...

A de-noising algorithm based on wavelet threshold-exponential adaptive window width-fitting for ground electrical source airborne transient electromagnetic signal

Science.gov (United States)

Ji, Yanju; Li, Dongsheng; Yu, Mingmei; Wang, Yuan; Wu, Qiong; Lin, Jun

2016-05-01

The ground electrical source airborne transient electromagnetic system (GREATEM) on an unmanned aircraft enjoys considerable prospecting depth, lateral resolution and detection efficiency, etc. In recent years it has become an important technical means of rapid resources exploration. However, GREATEM data are extremely vulnerable to stationary white noise and non-stationary electromagnetic noise (sferics noise, aircraft engine noise and other human electromagnetic noises). These noises will cause degradation of the imaging quality for data interpretation. Based on the characteristics of the GREATEM data and major noises, we propose a de-noising algorithm utilizing wavelet threshold method and exponential adaptive window width-fitting. Firstly, the white noise is filtered in the measured data using the wavelet threshold method. Then, the data are segmented using data window whose step length is even logarithmic intervals. The data polluted by electromagnetic noise are identified within each window based on the discriminating principle of energy detection, and the attenuation characteristics of the data slope are extracted. Eventually, an exponential fitting algorithm is adopted to fit the attenuation curve of each window, and the data polluted by non-stationary electromagnetic noise are replaced with their fitting results. Thus the non-stationary electromagnetic noise can be effectively removed. The proposed algorithm is verified by the synthetic and real GREATEM signals. The results show that in GREATEM signal, stationary white noise and non-stationary electromagnetic noise can be effectively filtered using the wavelet threshold-exponential adaptive window width-fitting algorithm, which enhances the imaging quality.

Remote sensing of soil moisture using airborne hyperspectral data

Science.gov (United States)

The Institute for Technology Development (ITD) has developed an airborne hyperspectral sensor system that collects electromagnetic reflectance data of the terrain. The system consists of sensors for three different sections of the electromagnetic spectrum; the Ultra-Violet (UV), Visible/Near Infrare...

Model structural uncertainty quantification and hydrologic parameter and prediction error analysis using airborne electromagnetic data

DEFF Research Database (Denmark)

Minsley, B. J.; Christensen, Nikolaj Kruse; Christensen, Steen

Model structure, or the spatial arrangement of subsurface lithological units, is fundamental to the hydrological behavior of Earth systems. Knowledge of geological model structure is critically important in order to make informed hydrological predictions and management decisions. Model structure...... is never perfectly known, however, and incorrect assumptions can be a significant source of error when making model predictions. We describe a systematic approach for quantifying model structural uncertainty that is based on the integration of sparse borehole observations and large-scale airborne...... electromagnetic (AEM) data. Our estimates of model structural uncertainty follow a Bayesian framework that accounts for both the uncertainties in geophysical parameter estimates given AEM data, and the uncertainties in the relationship between lithology and geophysical parameters. Using geostatistical sequential...

Extending airborne electromagnetic surveys for regional active layer and permafrost mapping with remote sensing and ancillary data, Yukon Flats ecoregion, central Alaska

Science.gov (United States)

Pastick, Neal J.; Jorgenson, M. Torre; Wylie, Bruce K.; Minsley, Burke J.; Ji, Lei; Walvoord, Michelle Ann; Smith, Bruce D.; Abraham, Jared D.; Rose, Joshua R.

2013-01-01

Machine-learning regression tree models were used to extrapolate airborne electromagnetic resistivity data collected along flight lines in the Yukon Flats Ecoregion, central Alaska, for regional mapping of permafrost. This method of extrapolation (r = 0.86) used subsurface resistivity, Landsat Thematic Mapper (TM) at-sensor reflectance, thermal, TM-derived spectral indices, digital elevation models and other relevant spatial data to estimate near-surface (0–2.6-m depth) resistivity at 30-m resolution. A piecewise regression model (r = 0.82) and a presence/absence decision tree classification (accuracy of 87%) were used to estimate active-layer thickness (ALT) (remote sensing and map data. At site scale, the predicted ALTs were similar to those previously observed for different vegetation types. At the landscape scale, the predicted ALTs tended to be thinner on higher-elevation loess deposits than on low-lying alluvial and sand sheet deposits of the Yukon Flats. The ALT and permafrost maps provide a baseline for future permafrost monitoring, serve as inputs for modelling hydrological and carbon cycles at local to regional scales, and offer insight into the ALT response to fire and thaw processes.

Geodetic and geophysical results from a Taiwan airborne gravity survey: Data reduction and accuracy assessment

DEFF Research Database (Denmark)

Hwang, C.W.; Hsiao, Y.S.; Shih, H.C.

2007-01-01

[ 1] An airborne gravity survey was conducted over Taiwan using a LaCoste and Romberg (LCR) System II air-sea gravimeter with gravity and global positioning system (GPS) data sampled at 1 Hz. The aircraft trajectories were determined using a GPS network kinematic adjustment relative to eight GPS ...... using airborne and surface gravity data and the other using surface data only, and the former yields a better agreement with the GPS-derived geoidal heights. Bouguer anomalies derived from airborne gravity by a rigorous numerical integration reveal important tectonic features....

Airborne gamma ray spectrometer surveying

International Nuclear Information System (INIS)

1991-01-01

The International Atomic Energy Agency (IAEA) in its role as collector and disseminator of information on nuclear techniques has long had an interest in gamma ray spectrometer methods and has published a number of Technical Reports on various aspects of the subject. At an Advisory Group Meeting held in Vienna in November 1986 to review appropriate activities the IAEA could take following the Chernobyl accident, it was recommended that preparation begin on a new Technical Report on airborne gamma ray spectrometer surveying, taking into account the use of the technique for environmental monitoring as well as for nuclear emergency response requirements. Shortly thereafter the IAEA became the lead organization in the Radioelement Geochemical Mapping section of the International Geological Correlation Programme/United Nations Educational, Scientific and Cultural Organization (UNESCO) Project on International Geochemical Mapping. These two factors led to the preparation of the present Technical Report. 18 figs, 4 tabs

Recent developments in airborne gamma ray surveying

International Nuclear Information System (INIS)

Grasty, Robert L.

1999-01-01

Standardized procedures have been developed for converting airborne gamma ray measurements to ground concentrations of potassium, uranium and thorium. These procedures make use of an airborne calibration range whose ground concentrations should be measured with a calibrated portable spectrometer rather than by taking geochemical samples. Airborne sensitivities and height attenuation coefficients are normally determined from flights over the calibration range but may not be applicable in mountainous areas. Mathematical techniques have been now developed to reduce statistical noise in the airborne measurements by utilizing up to 256 channels of spectral information. (author)

Karoo airborne geophysical survey

International Nuclear Information System (INIS)

Cole, D.J.; Stettler, E.H.

1984-01-01

Thirty four uranium anomalies were selected for ground follow-up from the analogue spectrometer records of Block 4 of the Karoo Airborne Geophysical Survey. The anomalies were plotted on 1:50 000 scale topographic maps and to 1:250 000 scale maps which are included in this report. The anomaly co-ordinates are tabulated together with the farms on which they occur. Results of the ground follow-up of the aerial anomalies are described. Twenty two anomalies are related to uranium mineralisation of which seventeen occur over baked mudstone adjacent to a dolerite intrusion. Five are located over fluvial channel sandstone of the Beaufort Group and subsurface mineralised sandstone may be present. The other twelve anomalies are spurious. Of the anomalies located over baked mudstone, fifteen emanate from ferruginous mudstone of the Whitehill Formation west of longitude 21 degrees 15 minutes. One of the two remaining anomalies over baked mudstone occurs over the Prince Albert Formation and the other anomaly is over baked mudstone and calcareous nodules of the Beaufort Group. The general low uranium values (less than 355 ppm eU3O8) render the occurrences uneconomic

Airborne Electromagnetic Mapping of Peatlands: a Case Study in Norway.

Science.gov (United States)

Silvestri, S.; Viezzoli, A.; Pfaffhuber, A. A.; Vettore, A.

2017-12-01

Peatlands are extraordinary reservoirs of organic carbon that can be found over a wide range of latitudes, in tropical, to temperate, to (sub)polar climates. According to some estimates, the carbon stored in peatlands almost match the atmospheric carbon pool. Peatlands degradation due to natural and anthropogenic factors releases every year large amount of CO2 and other green house gasses into the atmosphere. The conservation of peatlands is therefore a key measure to reduce emissions and to mitigate climate change. An effective plan to prevent peatlands degradation must move from a precise estimate of the volume of peat stored across vast territories around the world. One example are the several bogs that characterize large surfaces in Norway. Our research combines the use of high spatial resolution satellite optical data with Airborne Electromagnetic (AEM) and field measurements in order to map the extension and thickness of peat in Brøttum, Ringsaker province, Norway. The methodology allows us to quantify the volume of peat as well as the organic carbon stock. The variable thickness typical of Norwegian bogs allows us to test the limits of the AEM methodology in resolving near surface peat layers. This project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 747809. Start date: 1 June 2017. Duration: 24 months

Karoo airborne geophysical survey: preliminary report on airborne radiometric data from block 12

International Nuclear Information System (INIS)

Day, R.W.; Wright, O.M.

1980-02-01

The analogue gamma-ray spectrometer records of block 12 of the Karoo airborne geophysical survey were studied and significant uranium anomalies were selected and graded. The anomalies were plotted on 1:50 000 scale maps and the co-ordinates of the anomalies were tabulated. The anomalies were transferred to 1:250 000 scale maps which are included in this report. The geological setting of the anomalies has been studied. Ground follow-up work has been recommended for anomalies which occur over mineralized pans and drainage channels, and the Lower Beaufort Stage. Other anomalies which occur over the Ecca Series, the Middle Beaufort Stage, the Upper Beaufort Stage and the Stormberg Series have also been recommended for ground investigation

Crow Ressurection: The Future of Airborne Electronic Attack

Science.gov (United States)

2013-06-01

strike assets by attempting to gain and maintain control of the electromagnetic spectrum. 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17...receiving his commission through Officer Training School in 2000, Major Howard served as an RC-135V/W RIVET JOINT EWO at Offutt AFB, Nebraska...significant Airborne Electronic Attack challenges in protecting strike assets by attempting to gain and maintain control of the electromagnetic spectrum

Calibrating a Salt Water Intrusion Model with Time-Domain Electromagnetic Data

DEFF Research Database (Denmark)

Herckenrath, Daan; Odlum, Nick; Nenna, Vanessa

2013-01-01

Salt water intrusion models are commonly used to support groundwater resource management in coastal aquifers. Concentration data used for model calibration are often sparse and limited in spatial extent. With airborne and ground-based electromagnetic surveys, electrical resistivity models can......, we perform a coupled hydrogeophysical inversion (CHI) in which we use a salt water intrusion model to interpret the geophysical data and guide the geophysical inversion. We refer to this methodology as a Coupled Hydrogeophysical Inversion-State (CHI-S), in which simulated salt concentrations...... are transformed to an electrical resistivity model, after which a geophysical forward response is calculated and compared with the measured geophysical data. This approach was applied for a field site in Santa Cruz County, California, where a time-domain electromagnetic (TDEM) dataset was collected...

Synoptic view of the different domains of application of airborne radiometric and spectrometric surveys in egypt

International Nuclear Information System (INIS)

Fouad, K.M.

1998-01-01

Airborne radiometric survey has been applied for more than three decades in egypt. Experience gained from the acquired data over different geological environments has revealed the importance of this geophysical tool in: 1. disclosure of anomalies of potential uranium deposits, 2. geological mapping, 3. environmental monitoring of natural radiometric background around nuclear facilities, as well as the detection of nuclear fallout resulting from local or foreign nuclear activities. The advent of recording of the discriminated gamma ray energies in the airborne 256-channel spectrometer has eventually resulted in the quantitative detection of uranium, thorium, and potassium and their elemental ratios in the rocks. This has greatly widened the scope of geophysical and geochemical application. When this type is coupled with airborne magnetometry, the geological and structural configuration is appreciably revealed in three dimensions. The important role played by the statistical method of analysis is also shown. Case histories from the eastern desert, and sinai peninsula, are exhibited to help manifest the wide variety of applications of radiometric and spectrometric surveys

Improved sampling for airborne surveys to estimate wildlife population parameters in the African Savannah

NARCIS (Netherlands)

Khaemba, W.; Stein, A.

2002-01-01

Parameter estimates, obtained from airborne surveys of wildlife populations, often have large bias and large standard errors. Sampling error is one of the major causes of this imprecision and the occurrence of many animals in herds violates the common assumptions in traditional sampling designs like

Airborne gravimetry for geoid and GOCE

DEFF Research Database (Denmark)

Forsberg, R.; Olesen, A. V.; Nielsen, E.

2014-01-01

DTU-Space has since 1996 carried out large area airborne surveys over both polar, tropical and temperate regions, especially for geoid determination and global geopotential models. Recently we have started flying two gravimeters (LCR and Chekan-AM) side by side for increased reliability and redun......DTU-Space has since 1996 carried out large area airborne surveys over both polar, tropical and temperate regions, especially for geoid determination and global geopotential models. Recently we have started flying two gravimeters (LCR and Chekan-AM) side by side for increased reliability...... in Antarctica and Tanzania based on DTU-Space aerogravity and GOCE. In both cases the airborne data validate GOCE to very high degrees, and confirms the synergy of airborne gravity and GOCE. For Antarctica, the deep interior Antarctic survey (continued in 2013 from a remote field camp), shows...... that it is possible efficiently to cover even the most remote regions on the planet with good aerogravity. With the recent termination of the GOCE mission, it is therefore timely to initiate a coordinated, preferably international, airborne gravity effort to cover the polar gap south of 83° S; such a survey can...

Survey of ambient electromagnetic and radio-frequency interference levels in nuclear power plants

International Nuclear Information System (INIS)

Kercel, S.W.; Moore, M.R.; Blakeman, E.D.; Ewing, P.D.; Wood, R.T.

1996-11-01

This document reports the results of a survey of ambient electromagnetic conditions in representative nuclear power plants. The U.S. Nuclear Regulatory Commission (NRC) Office of Nuclear Regulatory Research engaged the Oak Ridge National Laboratory (ORNL) to perform these measurements to characterize the electromagnetic interference (EMI) and radio-frequency interference (RFI) levels that can be expected in nuclear power plant environments. This survey is the first of its kind, being based on long-term unattended observations. The data presented in this report were measured at eight different nuclear units and required 14 months to collect. A representative sampling of power plant conditions (reactor type, operating mode, site location) monitored over extended observation periods (up to 5 weeks) were selected to more completely determine the characteristic electromagnetic environment for nuclear power plants. Radiated electric fields were measured over the frequency range of 5 MHz to 8 GHz. Radiated magnetic fields and conducted EMI events were measured over the frequency range of 305 Hz to 5 MHz. Highest strength observations of the electromagnetic ambient environment across all measurement conditions at each site provide frequency-dependent profiles for EMI/RFI levels in nuclear power plants

Study on temperature field airborne remote sensing survey along shore nuclear power station in different tide status

International Nuclear Information System (INIS)

Liang Chunli; Li Mingsong

2010-01-01

Nuclear Power Station needs to let large quantity of cooling water to the near sea area when it is running. Whether the cooling water has effect to surrounding environment and the running of Nuclear Power Station needs further research. Temperature Drainage Mathematic Model and Physical Analogue Model need to acquire the distribution characteristic of near Station sea surface temperature field in different seasons and different tide status. Airborne Remote Sending Technique has a advantage in gaining high resolution sea surface temperature in different tide status, and any other manual method with discrete point survey can not reach it. After a successful implementation of airborne remote sensing survey to gain the near-shore temperature drainage information in Qinshan Nuclear Power Station, it provides the reference methods and ideas for temperature drainage remote sensing survey of Nuclear Power Station. (authors)

Delineation of the hydrogeologic framework of the Big Sioux aquifer near Sioux Falls, South Dakota, using airborne electromagnetic data

Science.gov (United States)

Valseth, Kristen J.; Delzer, Gregory C.; Price, Curtis V.

2018-03-21

The U.S. Geological Survey, in cooperation with the City of Sioux Falls, South Dakota, began developing a groundwater-flow model of the Big Sioux aquifer in 2014 that will enable the City to make more informed water management decisions, such as delineation of areas of the greatest specific yield, which is crucial for locating municipal wells. Innovative tools are being evaluated as part of this study that can improve the delineation of the hydrogeologic framework of the aquifer for use in development of a groundwater-flow model, and the approach could have transfer value for similar hydrogeologic settings. The first step in developing a groundwater-flow model is determining the hydrogeologic framework (vertical and horizontal extents of the aquifer), which typically is determined by interpreting geologic information from drillers’ logs and surficial geology maps. However, well and borehole data only provide hydrogeologic information for a single location; conversely, nearly continuous geophysical data are collected along flight lines using airborne electromagnetic (AEM) surveys. These electromagnetic data are collected every 3 meters along a flight line (on average) and subsequently can be related to hydrogeologic properties. AEM data, coupled with and constrained by well and borehole data, can substantially improve the accuracy of aquifer hydrogeologic framework delineations and result in better groundwater-flow models. AEM data were acquired using the Resolve frequency-domain AEM system to map the Big Sioux aquifer in the region of the city of Sioux Falls. The survey acquired more than 870 line-kilometers of AEM data over a total area of about 145 square kilometers, primarily over the flood plain of the Big Sioux River between the cities of Dell Rapids and Sioux Falls. The U.S. Geological Survey inverted the survey data to generate resistivity-depth sections that were used in two-dimensional maps and in three-dimensional volumetric visualizations of the Earth

Mapping Aquifer Systems with Airborne Electromagnetics in the Central Valley of California

Science.gov (United States)

Knight, R. J.; Smith, R.; Asch, T. H.; Abraham, J.; Cannia, J.; Fogg, G. E.; Viezzoli, A.

2016-12-01

The Central Valley of California is an important agricultural region struggling to meet the need for irrigation water. Recent periods of drought have significantly reduced the delivery of surface water, resulting in extensive pumping of groundwater. This has exacerbated an already serious problem in the Central Valley, where a number of areas have experienced declining water levels for several decades leading to ongoing concerns about depletion of aquifers and impacts on ecosystems, as well as subsidence of the ground surface. The overdraft has been so significant, that there are now approximately140 million acre-feet (MAF) of unused groundwater storage in the Central Valley, storage that could be used to complement the 42 MAF of surface storage. The alluvial sedimentary geology of the Central Valley is typically composed of more than 50 to 70 percent fine-grained deposits dominated by silt and clay beds. These fine grained deposits can block potential recharge, and are associated with the large amount of observed subsidence. Fortunately, the geologic processes that formed the region created networks of sand and gravel which provide both a supply of water and pathways for recharge from the surface to the aquifers. The challenge is to find these sand and gravel deposits and thus identify optimal locations for surface spreading techniques so that recharge could be dramatically increased, and re-pressurization of the confined aquifer networks could be accomplished. We have acquired 100 line kilometers of airborne electromagnetic data over an area in the San Joaquin Valley, imaging the subsurface hydrostratigraphy to a depth of 500 m with spatial resolution on the order of meters to tens of meters. Following inversion of the data to obtain resistivity models along the flight lines, we used lithology logs in the area to transform the models to images displaying the distribution of sand and gravel, clay, and mixed fine and coarse materials. The quality of the data and

Coil response inversion for very early time modelling of helicopter-borne time-domain electromagnetic data and mapping of near-surface geological layers

DEFF Research Database (Denmark)

Schamper, Cyril Noel Clarence; Auken, Esben; Sørensen, Kurt Ingvard K.I.

2014-01-01

Very early times in the order of 2-3 μs from the end of the turn-off ramp for time-domain electromagnetic systems are crucial for obtaining a detailed resolution of the near-surface geology in the depth interval 0-20 m. For transient electromagnetic systems working in the off time, an electric cu...... resolution of shallow geological layers in the depth interval 0-20 m. This is proved by comparing results from the airborne electromagnetic survey to more than 100 km of Electrical Resistivity Tomography measured with 5 m electrode spacing.......Very early times in the order of 2-3 μs from the end of the turn-off ramp for time-domain electromagnetic systems are crucial for obtaining a detailed resolution of the near-surface geology in the depth interval 0-20 m. For transient electromagnetic systems working in the off time, an electric...

Prognoses of prospective areas for uranium metallogenesis with full-spectrum information of airborne gamma-ray survey

International Nuclear Information System (INIS)

Hu Mingkao; Shen Zhengxin; Li Binghai; Cai Genqing

2010-01-01

This paper briefly introduces the development of airborne radioactive survey and the background of carrying out full-spectrum study. It also introduces the method, standard and application example of using the full-spectrum information of airborne gamma spectrum to predict U-metallogenic prospective areas. The field checking has found that uranium in the water of the prospective area is three magnitude higher than that in the normal area. The developmment and the application of this method will play a multiplier role in reusing the library stored data evaluating uranium resource potential in our Country. (authors)

Airborne gamma survey of the historic Sleisbeck mine area in the Northern Territory, Australia, and its use for site rehabilitation planning

International Nuclear Information System (INIS)

Bollhoefer, A.; Pfitzner, K.; Ryan, B.; Martin, P.; Fawcett, M.; Jones, D.R.

2008-01-01

An airborne γ-survey provided information about the extent of radioactive contamination around the historic Sleisbeck mine. Quickbird satellite data were acquired to relate airborne measurements to land cover features. Enhanced equivalent uranium (eU) levels were found to be confined to the mine and low grade waste rock dumps. The average terrestrial background radiation dose rate estimated from the airborne gamma survey data was 0.10-0.14 μGy h -1 while the area around the mine exhibited a maximum of ∼2.3 μGy h -1 , but measurements on the ground indicate that this maximum is exceeded in some localized areas. Rehabilitation of the site is likely to result in a threefold reduction in radiation doses to people accessing the area

SURVEY OF CULTURABLE AIRBORNE BACTERIA AT FOUR DIVERSE LOCATIONS IN OREGON: URBAN, RURAL, FOREST, AND COASTAL

Science.gov (United States)

To determine the risks of microbial air pollution from microorganisms used for pesticides and bioremediation, or emanating from composting, fermentation tanks, or other agricultural and urban sources, airborne microbial levels must be evaluated. This study surveyed the atmospheri...

Research on airborne comprehensive survey system of atmosphere quality

International Nuclear Information System (INIS)

Yu Zhentao; Yu Yanbin

1998-01-01

The global atmosphere pollution is becoming more and more serious, affecting the human existence and development. Besides, the high spectrum resolution remote sensing technique, which has been applied to observe topographic features, identify military objectives and distinguish lithology and vegetation, has the relation to atmosphere quality and is influenced by atmosphere pollution (including radon pollution) and dust content in the atmosphere, it is imperative to monitor atmosphere quality. Based upon the selection of some main parameters evaluating atmospheric quality and necessary equipment, the author introduces the design of multiple airborne comprehensive survey system of atmosphere quality and how to deal with problems that crop up during the hardware designing and software programming

Airborne full tensor magnetic gradiometry surveys in the Thuringian basin, Germany

Science.gov (United States)

Queitsch, M.; Schiffler, M.; Goepel, A.; Stolz, R.; Meyer, M.; Meyer, H.; Kukowski, N.

2013-12-01

In this contribution we introduce a newly developed fully operational full tensor magnetic gradiometer (FTMG) instrument based on Superconducting Quantum Interference Devices (SQUIDs) and show example data acquired in 2012 within the framework of the INFLUINS (Integrated Fluid Dynamics in Sedimentary basins) project. This multidisciplinary project aims for a better understanding of movements and interaction between shallow and deep fluids in the Thuringian Basin in the center of Germany. In contrast to mapping total magnetic field intensity (TMI) in conventional airborne magnetic surveys for industrial exploration of mineral deposits and sedimentary basins, our instrument measures all components of the magnetic field gradient tensor using highly sensitive SQUID gradiometers. This significantly constrains the solutions of the inverse problem. Furthermore, information on the ratio between induced and remanent magnetization is obtained. Special care has been taken to reduce motion noise while acquiring data in airborne operation. Therefore, the sensors are mounted in a nonmagnetic and aerodynamically shaped bird made of fiberglas with a high drag tail which stabilizes the bird even at low velocities. The system is towed by a helicopter and kept at 30m above ground during data acquisition. Additionally, the system in the bird incorporates an inertial unit for geo-referencing and enhanced motion noise compensation, a radar altimeter for topographic correction and a GPS system for high precision positioning. Advanced data processing techniques using reference magnetometer and inertial unit data result in a very low system noise of less than 60 pT/m peak to peak in airborne operation. To show the performance of the system we present example results from survey areas within the Thuringian basin and along its bordering highlands. The mapped gradient tensor components show a high correlation to existing geologic maps. Furthermore, the measured gradient components indicate

Airborne electromagnetic detection of shallow seafloor topographic features, including resolution of multiple sub-parallel seafloor ridges

Science.gov (United States)

Vrbancich, Julian; Boyd, Graham

2014-05-01

The HoistEM helicopter time-domain electromagnetic (TEM) system was flown over waters in Backstairs Passage, South Australia, in 2003 to test the bathymetric accuracy and hence the ability to resolve seafloor structure in shallow and deeper waters (extending to ~40 m depth) that contain interesting seafloor topography. The topography that forms a rock peak (South Page) in the form of a mini-seamount that barely rises above the water surface was accurately delineated along its ridge from the start of its base (where the seafloor is relatively flat) in ~30 m water depth to its peak at the water surface, after an empirical correction was applied to the data to account for imperfect system calibration, consistent with earlier studies using the same HoistEM system. A much smaller submerged feature (Threshold Bank) of ~9 m peak height located in waters of 35 to 40 m depth was also accurately delineated. These observations when checked against known water depths in these two regions showed that the airborne TEM system, following empirical data correction, was effectively operating correctly. The third and most important component of the survey was flown over the Yatala Shoals region that includes a series of sub-parallel seafloor ridges (resembling large sandwaves rising up to ~20 m from the seafloor) that branch out and gradually decrease in height as the ridges spread out across the seafloor. These sub-parallel ridges provide an interesting topography because the interpreted water depths obtained from 1D inversion of TEM data highlight the limitations of the EM footprint size in resolving both the separation between the ridges (which vary up to ~300 m) and the height of individual ridges (which vary up to ~20 m), and possibly also the limitations of assuming a 1D model in areas where the topography is quasi-2D/3D.

Analysis of airborne LiDAR surveys to quantify the characteristic morphologies of northern forested wetlands

Science.gov (United States)

Murray C. Richardson; Carl P. J. Mitchell; Brian A. Branfireun; Randall K. Kolka

2010-01-01

A new technique for quantifying the geomorphic form of northern forested wetlands from airborne LiDAR surveys is introduced, demonstrating the unprecedented ability to characterize the geomorphic form of northern forested wetlands using high-resolution digital topography. Two quantitative indices are presented, including the lagg width index (LWI) which objectively...

Ground-penetrating radar and electromagnetic surveys at the Monroe Crossroads battlefield site, Fort Bragg, North Carolina

Science.gov (United States)

Kessler, Richard; Strain, R.E.; Marlowe, J. I.; Currin, K.B.

1996-01-01

A ground-penetrating radar survey was conducted at the Monroe Crossroads Battlefield site at Fort Bragg, North Carolina, to determine possible locations of subsurface archaeological features. An electromagnetic survey also was conducted at the site to verify and augment the ground-penetrating radar data. The surveys were conducted over a 67,200-square-foot grid with a grid point spacing of 20 feet. During the ground-penetrating radar survey, 87 subsurface anomalies were detected based on visual inspection of the field records. These anomalies were flagged in the field as they appeared on the ground-penetrating radar records and were located by a land survey. The electromagnetic survey produced two significant readings at ground-penetrating radar anomaly locations. The National Park Service excavated 44 of the 87 anomaly locations at the Civil War battlefield site. Four of these excavations produced significant archaeological features, including one at an abandoned well.

ELABORATION OF THE 3D MODEL AND SURVEY OF THE POWER LINES USING DATA FROM AIRBORNE LASER SCANNING

Directory of Open Access Journals (Sweden)

Bogusława Kwoczyńska

2016-09-01

Full Text Available One of the methods of obtaining highly accurate and current spatial data about the terrain, as well as objects situated on it, is laser scanning. LIDAR (Light Detection and Ranging is among the most modern, dynamically developing technologies and reveals in surveying new capabilities that have been unachievable in a traditional way so far. The aim of the publication is to show the possibilities of using data from airborne laser scanning to perform the survey and visualization of the energy network, and also identification of hazards which the present network constitutes for the immediate environment using the TerraSolid software package. The survey was conducted for two independent sections of the power line, on the basis of two different clouds of points obtained from the airborne laser scanning. The first one had a density of 16 points/m2, while the other 22 pts/m2. The project was created in an environment of MicroStation V8i software using special overlays – TerraScan and TerraModeler of Finnish TerraSolid Company. The use of the test clouds of different densities was intended to indicate an optimal density of the cloud of points, which allows carrying out a survey and visualization of the energy network based on data derived from airborne laser scanning. The publication presents on particular examples the procedure of vectorization and visualization of the power line and detection of objects within a dangerous distance from it. The possibility of using applied LIDAR data, meeting the industry requirements, to the survey of power lines has been also confirmed.

Airborne geophysics for mesoscale observations of polar sea ice in a changing climate

Science.gov (United States)

Hendricks, S.; Haas, C.; Krumpen, T.; Eicken, H.; Mahoney, A. R.

2016-12-01

Sea ice thickness is an important geophysical parameter with a significant impact on various processes of the polar energy balance. It is classified as Essential Climate Variable (ECV), however the direct observations of the large ice-covered oceans are limited due to the harsh environmental conditions and logistical constraints. Sea-ice thickness retrieval by the means of satellite remote sensing is an active field of research, but current observational capabilities are not able to capture the small scale variability of sea ice thickness and its evolution in the presence of surface melt. We present an airborne observation system based on a towed electromagnetic induction sensor that delivers long range measurements of sea ice thickness for a wide range of sea ice conditions. The purpose-built sensor equipment can be utilized from helicopters and polar research aircraft in multi-role science missions. While airborne EM induction sounding is used in sea ice research for decades, the future challenge is the development of unmanned aerial vehicle (UAV) platform that meet the requirements for low-level EM sea ice surveys in terms of range and altitude of operations. The use of UAV's could enable repeated sea ice surveys during the the polar night, when manned operations are too dangerous and the observational data base is presently very sparse.

Report on airborne radioactivity surveys and the uranium deposits in the Red River region of Texas and Oklahoma

International Nuclear Information System (INIS)

Blair, R.G.; Stehle, F.T.; Levich, R.A.

1973-11-01

The U. S. Atomic Energy Commission conducted an airborne radioactivity survey of the Red River region of Texas and Oklahoma beginning in December 1955 and ending in May 1956. All or parts of Archer, Clay, and Montague Counties in northern Texas and Carter, Cotton, Jefferson, and Stephens Counties in southern Oklahoma were surveyed. Particular attention was paid to those areas where exposures are found of red beds of the Permian Wichita Group. Field examinations were conducted of anomalies discovered by airborne reconnaissance as well as those reported by private individuals. Forty localities were examined, the majority in sandstones, siltstones, or conglomerates. Uranium and copper minerals were identified at several localities. Ferruginous staining, bleaching of the sandstone color, calcium carbonate cement, and carbonized plant remains are common to the deposits

Advances and perspectives in bathymetry by airborne lidar

Science.gov (United States)

Zhou, Guoqing; Wang, Chenxi; Li, Mingyan; Wang, Yuefeng; Ye, Siqi; Han, Caiyun

2015-12-01

In this paper, the history of the airborne lidar and the development stages of the technology are reviewed. The basic principle of airborne lidar and the method of processing point-cloud data were discussed. At present, single point laser scanning method is widely used in bathymetric survey. Although the method has high ranging accuracy, the data processing and hardware system is too much complicated and expensive. For this reason, this paper present a kind of improved dual-frequency method for bathymetric and sea surface survey, in this method 176 units of 1064nm wavelength laser has been used by push-broom scanning and due to the airborne power limits still use 532nm wavelength single point for bathymetric survey by zigzag scanning. We establish a spatial coordinates for obtaining the WGS-84 of point cloud by using airborne POS system.

Survey and analysis on environmental and electromagnetic effect on instrumentation and control equipment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Hwang, In Koo; Lee, Dong Young; Cha, Kyung Ho

2001-03-01

As the instrumentation and control (I and C) equipment suppliers tend to provide digital components rather than conventional analog type components for instrumentation and control systems of nuclear power plants(NPPs), it is unavoidable to adopt digital equipment for safety I and C systems as well as non-safety systems. However, the full introduction of digital equipment for I and C systems of nuclear power plants raises several concerns which have not been considered in conventional analog I and C equipment. The two major examples of the issues of digital systems are environmental/electromagnetic compatibility (EMC) and software reliability. This report presents the survey and research results on environmental and electromagnetic effect on I and C equipment of nuclear power plants to give a guideline for aging management and design process. Electromagnetic site surveys were conducted to be used as a part of technical basis to demonstrate that I and C systems are compatible with the ambient electromagnetic noise in Korean nuclear power plants.

Correcting for static shift of magnetotelluric data with airborne electromagnetic measurements: a case study from Rathlin Basin, Northern Ireland

Directory of Open Access Journals (Sweden)

R. Delhaye

2017-05-01

Full Text Available Galvanic distortions of magnetotelluric (MT data, such as the static-shift effect, are a known problem that can lead to incorrect estimation of resistivities and erroneous modelling of geometries with resulting misinterpretation of subsurface electrical resistivity structure. A wide variety of approaches have been proposed to account for these galvanic distortions, some depending on the target area, with varying degrees of success. The natural laboratory for our study is a hydraulically permeable volume of conductive sediment at depth, the internal resistivity structure of which can be used to estimate reservoir viability for geothermal purposes; however, static-shift correction is required in order to ensure robust and precise modelling accuracy.We present here a possible method to employ frequency–domain electromagnetic data in order to correct static-shift effects, illustrated by a case study from Northern Ireland. In our survey area, airborne frequency domain electromagnetic (FDEM data are regionally available with high spatial density. The spatial distributions of the derived static-shift corrections are analysed and applied to the uncorrected MT data prior to inversion. Two comparative inversion models are derived, one with and one without static-shift corrections, with instructive results. As expected from the one-dimensional analogy of static-shift correction, at shallow model depths, where the structure is controlled by a single local MT site, the correction of static-shift effects leads to vertical scaling of resistivity–thickness products in the model, with the corrected model showing improved correlation to existing borehole wireline resistivity data. In turn, as these vertical scalings are effectively independent of adjacent sites, lateral resistivity distributions are also affected, with up to half a decade of resistivity variation between the models estimated at depths down to 2000 m. Simple estimation of differences in bulk

PIXE analysis of airborne particulate matter from Monterrey, Mexico. A first survey

International Nuclear Information System (INIS)

Aldape, F.; Flores M, J.; Diaz, R.V.; Hernandez-Mendez, B.; Montoya Z, J.M.; Blanco, E.E.; Fuentes, A.F.; Torres-Martinez, L.M.

1999-01-01

A first survey of elemental contents in airborne particulate matter from Monterrey, Nuevo Leon, Mexico, was performed using PIXE. This second largest industrial city is located 715 km north of Mexico City, and counts with a population of nearly three million inhabitants in its conurbation. Air pollution in the place comes from a great variety of industries ranging from iron smelters to furniture manufacturing, as well as from fuel combustion in vehicles and industries. This study presents results of elemental contents in airborne particulate matter in two particle size fractions: PM 2.5 and PM 15 . The samples were collected during five weeks on working days, Monday-Friday, from 9 December 1996 to 14 January 1997. Two samples a day were collected, 12 h each, night-time and day-time. These first results show local pollution as typical from a large urban area in conjunction with an active industry. Thirteen elements were consistently detected in most of the samples and some episodes due to both industrial and human activities were identified. A general discussion about the results obtained is presented

Clean enough for industry? An airborne geophysical case study

International Nuclear Information System (INIS)

Nyquist, J.E.; Beard, L.P.

1996-01-01

Data from two airborne geophysical surveys of the Department of Energy's Oak Ridge Reservation (ORR) were extremely valuable in deciding whether a 1000-acre (400 hectare) parcel of the ORR should be released to the City of Oak Ridge for industrial development. Our findings, based on electromagnetic and magnetic data, were incorporated in the federally mandated Environmental Assessment Statement (EAS), and in general supported claims that this land was never used as a hazardous waste disposal site. We estimated the amount of iron required to produce each anomaly using a simple dipole model. All anomalies with equivalent sources greater than approximately 1000 kg of iron were checked in the field, and the source of all but one identified as either a bridge, reinforced concrete debris, or a similarly benign object. Additionally, some smaller anomalies (equivalent sources of roughly 500 kg) have been checked; thus far, these also have innocuous sources. Airborne video proved invaluable in identifying logging equipment as the source of some of these anomalies. Geologic noise may account for some of the remaining anomalies. Naturally occurring accumulations of magnetic minerals in the soil on the ORR have been shown to produce anomalies which, at a sensor height of 30 m, are comparable to the anomaly produced by about 500 kg of iron. By comparison, the electronic noise of the magnetic gradiometer, 0.01--0.02 nT/m, is equivalent to only about 50--100 kg of iron at a 30 m sensor height. The electromagnetic data, combined with field mapping of karst structures, provided evidence of a northeast-southwest striking conduit spanning the parcel. The possible existence of a karst conduit led the EAS authors to conclude that this is a ''sensitive hydrologic setting.'' We conclude that aerial geophysics is an extremely cost-effective, and efficient technique for screening large tracts of land for environmental characterization

The Danish airborne gamma-ray surveying results

Energy Technology Data Exchange (ETDEWEB)

Hovgaard, J. [Danish Emergency Management Agency, Birkeroed (Denmark)

1997-12-31

The Danish Emergency Management Agency (DEMA) in co-operation with the Technical University of Denmark (TUD), Department of Automation, participated in the international exercise RESUME-95 arranged in Finland in August 1995. DEMA performed measurement with their airborne gamma-ray surveying system. Surveys were done in the three areas known as AREA I, II, III. Results from AREA II (3 km x 6 km) show that the apparent {sup 137}Cs deposition assuming a deposition profile equal to the profile in AREA I based on soil samples varies from a few 10th kBqm{sup -2} up to 110 kBqm{sup -2}. However, a detailed analysis using a new method, Noise Adjusted Singular Value Decomposition (NASVD), shows that the true variations probably are smaller and that the observed differences to some extend are due to major variations in the depth distribution of the cesium. For example agricultural areas appears to have cesium much deeper deposit than the undisturbed areas. Another interesting result is that the NASVD analysis shows that the ration of {sup 134}Cs to {sup 137}Cs is fixed and approximately 0.03 (August 1995) a number in good agreement with the expected ratio from the Chernobyl accident. No true real-time software for source detection is yet integrated in the Danish system. Results from AREA III, however, show that the implemented software for rapid post processing of data worked excellent for detection of radioactive sources. Post analysis using NASVD demonstrates that all sources except for a small {sup 137}Cs source can be localized. (au).

The Danish airborne gamma-ray surveying results

Energy Technology Data Exchange (ETDEWEB)

Hovgaard, J [Danish Emergency Management Agency, Birkeroed (Denmark)

1998-12-31

The Danish Emergency Management Agency (DEMA) in co-operation with the Technical University of Denmark (TUD), Department of Automation, participated in the international exercise RESUME-95 arranged in Finland in August 1995. DEMA performed measurement with their airborne gamma-ray surveying system. Surveys were done in the three areas known as AREA I, II, III. Results from AREA II (3 km x 6 km) show that the apparent {sup 137}Cs deposition assuming a deposition profile equal to the profile in AREA I based on soil samples varies from a few 10th kBqm{sup -2} up to 110 kBqm{sup -2}. However, a detailed analysis using a new method, Noise Adjusted Singular Value Decomposition (NASVD), shows that the true variations probably are smaller and that the observed differences to some extend are due to major variations in the depth distribution of the cesium. For example agricultural areas appears to have cesium much deeper deposit than the undisturbed areas. Another interesting result is that the NASVD analysis shows that the ration of {sup 134}Cs to {sup 137}Cs is fixed and approximately 0.03 (August 1995) a number in good agreement with the expected ratio from the Chernobyl accident. No true real-time software for source detection is yet integrated in the Danish system. Results from AREA III, however, show that the implemented software for rapid post processing of data worked excellent for detection of radioactive sources. Post analysis using NASVD demonstrates that all sources except for a small {sup 137}Cs source can be localized. (au).

Airborne gamma-ray spectrometer and magnetometer survey, Meade River Quadrangle, Alaska. Final report

International Nuclear Information System (INIS)

1981-02-01

The results obtained from an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over the Meade River map area of Alaska are presented. Based on the criteria outlined in the general section on interpretation, a total of eight uranium anomalies have been outlined on the interpretation map. Most of these are only weakly to moderately anomalous. Zones 3 and 7 are relatively better than the others though none of the anomalies are thought to be of any economic significance. No follow-up work is recommended

Airborne gamma-ray spectrometer and magnetometer survey: north/south tieline. Final report

International Nuclear Information System (INIS)

1981-05-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted along the 99 0 longitude meridian from the Canadian border southward to the Mexican border. A total of 1555 line miles of geophysical data were acquired and, subsequently, compiled. The north-south tieline was flown as part of the National Uranium Resources Evaluation. NURE is a program of the US Department of Energy's Grand Junction, Colorado, office to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

3-D inversion of airborne electromagnetic data parallelized and accelerated by local mesh and adaptive soundings

Science.gov (United States)

Yang, Dikun; Oldenburg, Douglas W.; Haber, Eldad

2014-03-01

Airborne electromagnetic (AEM) methods are highly efficient tools for assessing the Earth's conductivity structures in a large area at low cost. However, the configuration of AEM measurements, which typically have widely distributed transmitter-receiver pairs, makes the rigorous modelling and interpretation extremely time-consuming in 3-D. Excessive overcomputing can occur when working on a large mesh covering the entire survey area and inverting all soundings in the data set. We propose two improvements. The first is to use a locally optimized mesh for each AEM sounding for the forward modelling and calculation of sensitivity. This dedicated local mesh is small with fine cells near the sounding location and coarse cells far away in accordance with EM diffusion and the geometric decay of the signals. Once the forward problem is solved on the local meshes, the sensitivity for the inversion on the global mesh is available through quick interpolation. Using local meshes for AEM forward modelling avoids unnecessary computing on fine cells on a global mesh that are far away from the sounding location. Since local meshes are highly independent, the forward modelling can be efficiently parallelized over an array of processors. The second improvement is random and dynamic down-sampling of the soundings. Each inversion iteration only uses a random subset of the soundings, and the subset is reselected for every iteration. The number of soundings in the random subset, determined by an adaptive algorithm, is tied to the degree of model regularization. This minimizes the overcomputing caused by working with redundant soundings. Our methods are compared against conventional methods and tested with a synthetic example. We also invert a field data set that was previously considered to be too large to be practically inverted in 3-D. These examples show that our methodology can dramatically reduce the processing time of 3-D inversion to a practical level without losing resolution

Voxel inversion of airborne EM data

DEFF Research Database (Denmark)

Fiandaca, Gianluca G.; Auken, Esben; Christiansen, Anders Vest C A.V.C.

2013-01-01

We present a geophysical inversion algorithm working directly in a voxel grid disconnected from the actual measuring points, which allows for straightforward integration of different data types in joint inversion, for informing geological/hydrogeological models directly and for easier incorporation...... of prior information. Inversion of geophysical data usually refers to a model space being linked to the actual observation points. For airborne surveys the spatial discretization of the model space reflects the flight lines. Often airborne surveys are carried out in areas where other ground......-based geophysical data are available. The model space of geophysical inversions is usually referred to the positions of the measurements, and ground-based model positions do not generally coincide with the airborne model positions. Consequently, a model space based on the measuring points is not well suited...

Airborne gamma-ray spectrometer and magnetometer survey, Sagavanirktok Quadrangle, Alaska. Volume I. Final report

International Nuclear Information System (INIS)

1981-03-01

The results obtained from an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over the Sagavanirktok map area of Alaska are presented. Based on the criteria outlined in the general section on interpretation, a total of eight uranium anomalies have been outlined on the interpretation map. However, all of these zones are only weakly to moderately anomalous. None are thought to be indicative of local enrichment of uranium to economically significant levels. No follow-up work is recommended

3-D modeling of surface, borehole, and airborne EM methods; Chijo konai kuchu denjiho no sanjigen modeling

Energy Technology Data Exchange (ETDEWEB)

Sasaki, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-22

Three-dimensional modelling methods using the difference method and finite element method are applied to the simulations respectively of the surface electromagnetic method, borehole electromagnetic method, and airborne electromagnetic method, and they are compared with each other in point of accuracy and practicality. The object of calculation in this study is a 3-D model which is a semi-finite medium 100 ohm/m in resistivity that contains a rectangular parallelopiped 1 ohm/m in resistivity. A vertical magnetic dipole is installed on the surface in the surface electromagnetic method, providing a vertical magnetic field on the surface. In the borehole electromagnetic method, a vertical magnetic dipole is placed in a borehole and the resultant vertical magnetic field is measured at a station in another borehole. In the airborne electromagnetic method, the flight level is 20m high and the distance between the source and the receiving point is 10m. The results of calculation all agree well with the results of calculation previously made known. When the difference method and finite element method are compared, it is found that the finite element method requires calculation time and memory capacity two to three times more than the difference method. 5 refs., 9 figs.

Development of an airborne gamma radiation system for snow surveys

Energy Technology Data Exchange (ETDEWEB)

Fritzsche, A E [EG and G, Inc., Las Vegas, NV (USA)

1979-01-01

An airborne gamma-snow survey system requires detailed design to obtain maximum precision and accuracy. The use of NaI(Te) gamma detectors with a full gamma energy spectrum pulse height analyzer together with a small computer provide a self-contained and flexible system. The dual detector method determines atmospheric radon perturbations in the detection system. Detailed calibration experiments must be performed to determine twenty parameters that describe the physical nature of the system. Multiple high altitude and lake flights are used to obtain background components. Simulation pads, loaded with varying concentrations of /sup 40/K, /sup 232/Th and /sup 23/..gamma..U yield photopeak stripping coefficients and basic system sensitivity. Multiple altitude flights over land lines provide air attenuation coefficients which may converted to water attenuation coefficients.

Airborne Gravity: NGS' Airborne Gravity Data for AN01 (2009-2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2009-2010 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum...

Manganese survey in airborne particulate matter from a mining area at Hidalgo State, Mexico

International Nuclear Information System (INIS)

Aldape, F.; Hernandez-Mendez, B.; Flores M, J.

1999-01-01

A manganese (Mn) survey in airborne particulate matter from a mining area located in Hidalgo State (Mexico) was performed using PIXE. Deposits of Mn ore, first discovered in 1959 and under continuous exploitation since 1962, are nowadays considered as one of the most important of their kind in the American Continent. Afterwards, local inhabitants have been under continuous overexposure to dusts and water highly enriched with Mn. Since no information was available about Mn content in airborne particulate matter in that area, especially in the respirable fraction PM 2.5 , airborne particles were collected simultaneously at two sites located on opposite sides of the rim of the mining valley, and along the line of prevailing local winds. The sample collection was performed on eight alternate days, taking two samples per day (day-time and night-time) at each sampling site, using Stacked Filter Units (SFUs) of the Davis design to separate particles into fine (PM 2.5 ) and coarse (PM 15 ) sizes. The samples were PIXE analyzed and the results of this study revealed that Mn content, in both fine and coarse fractions, were in excess of the general urban background level of 40 ng/m 3 (US Environmental Protection Agency, 1990) in more than 50% of the samples, which indicate severe environmental deterioration in the place under study

Airborne gamma-ray spectrometer and magnetometer survey. Volume I. Final report

International Nuclear Information System (INIS)

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Mariposa, California and Nevada; Fresno, California; and Bakersfield, Caifornia 1:250,000 National Topographic Map Series (NTMS) 1 0 x 2 0 quadrangle maps. The survey was a part of DOE's National Aerial Radiometric Reconnaissance (ARR) program, which in turn is a part of the National Uranium Resource Evaluation (NURE) program. Data were collected by a helicopter equipped with a gamma-ray spectrometer having a large crystal volume, and a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test range. Data quality was ensured throughout the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. These maps were interpreted and an anomaly interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data processing procedures, the data display format, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

Three decades of BGR airborne geophysical surveys over the polar regions - a review

Science.gov (United States)

Damaske, Detlef

2013-04-01

The Federal Institute for Geosciences and Natural Resources (BGR) has been conducting geological polar research since 1979. A few years later BGR engaged in airborne geophysical projects. Investigation of the lithosphere of the continent and the continental margins was one of the key issues for BGR. Right from the beginning geophysical research was closely associated with the geological activities. The GANOVEX (German Antarctic North Victoria Land Expedition) program combined geological research with geophysical (mainly airborne) investigations. This proved to be a fruitful approach to many of the open questions regarding the tectonic development of the Ross Sea region. Aeromagnetic surveys evolved into a powerful tool for identifying geological structures and following them underneath the ice covered areas - not accessible to direct geological investigations. To achieve this aim it was essential to lay out these surveys with a relatively closely spaced line separation on the expense of covering large areas at the same time. Nevertheless, over many years of continues research areas of more than a just regional extent could be covered. This was, however, only possible through international collaboration. During the first years, working in the Ross Sea area, the cooperation with the US and Italian programs played a significant role, especially the GITARA (German-Italian Aeromagnetic Research in Antarctica) program has to be mentioned. GEOMAUD (Geoscientific Expedition to Dronning Maud Land) and the German-Australian joint venture PCMEGA (Prince Charles Mountains Expedition of Germany & Australia) expanded research activities to the East Antarctic shield area. In the International Polar Year (IPY), BGR played a leading role in the international project AGAP (Antarctica's GAmburtsev Province) as part of the main topic "Venture into Unknown Regions". AGAP was jointly conducted by the USA, Great Britain, Australia, China and Germany. While in the Ross Sea area even

Airborne Magnetic Trackline Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA National Centers for Environmental Information (formerly National Geophysical Data Center) receive airborne magnetic survey data from US and non-US...

Airborne electromagnetics supporting salinity and natural resource management decisions at the field scale in Australia

NARCIS (Netherlands)

Cresswell, R.G.; Mullen, I.C.; Kingham, R.; Kellett, J.; Dent, D.L.; Jones, G.L.

2007-01-01

Airborne geophysics has been used at the catchment scale to map salt stores, conduits and soil variability, but few studies have evaluated its usefulness as a land management tool at the field scale. We respond to questions posed by land managers with: (1) comparison of airborne and ground-based

The effect of extreme-low-frequency electromagnetic field on air ...

African Journals Online (AJOL)

Electromagnetic fields produce alternating electric fields and modify static electric fields in the vicinity. These electric fields, if large enough, can alter the concentration or transport of airborne particles (including particles harmful to health). In this study, the concentration of radioactive materials (gamma radiation) was ...

Airborne gamma-ray spectrometer and magnetometer survey, Mitchell Quadrangle, South Dakota. Final report

International Nuclear Information System (INIS)

1981-04-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the Mitchell map area. The purpose of this program is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1479 line miles are in this quadrangle

Airborne gamma-ray spectrometer and magnetometer survey: Huron quadrangle, South Dakota. Final report

International Nuclear Information System (INIS)

1981-04-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the Huron map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1459 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

The multilevel fast multipole algorithm (MLFMA) for solving large-scale computational electromagnetics problems

CERN Document Server

Ergul, Ozgur

2014-01-01

The Multilevel Fast Multipole Algorithm (MLFMA) for Solving Large-Scale Computational Electromagnetic Problems provides a detailed and instructional overview of implementing MLFMA. The book: Presents a comprehensive treatment of the MLFMA algorithm, including basic linear algebra concepts, recent developments on the parallel computation, and a number of application examplesCovers solutions of electromagnetic problems involving dielectric objects and perfectly-conducting objectsDiscusses applications including scattering from airborne targets, scattering from red

Airborne radiometric: Data evaluation and calibration

International Nuclear Information System (INIS)

Wendt, I.; Sengpiel, K.P.; Lenz, H.

1984-01-01

The airborne geophysical system of the BGR (German Geological Survey) consists of a helicopter equipped with an electromagnetic system with two transmittors and two receivers, a proton resonance magnetometer and a 16 L NaJ-crystal with four channel recording. All these data together with navigation data and flight altitude above ground are recorded each second on a nine track magnetic tape for further data evaluation. Different corrections have to be applied to the rough data such as: smoothing by means of a digital filter to reduce statistical noise, altitude correction, Compton-correction, and drift correction (cross-profile evaluation). Then the corrected measuring data are combined with the navigation data in order to be able to produce iso-line maps. The final results are presented as: line plots for U, Th, and K (and EM-data and magnetometer data); actual flight line plots; iso-line maps for U, Th, and K; iso-line maps for conductivity; depth of conducting layer; and magnetometry maps. The procedures of correction and evaluation of the above mentioned data as well as the calibration of the NaJ-detector in terms of ppm U, Th, and %K are dicussed in the paper. (author)

Electromagnetic surveys to detect clay-rich sediment in the Rio Grande inner valley, Albuquerque area, New Mexico

Science.gov (United States)

Bartolino, James R.; Sterling, Joseph M.

2000-01-01

Information on the presence of clay-rich layers in the inner-valley alluvium is essential for quantifying the amount of water transmitted between the Rio Grande and the Santa Fe Group aquifer system. This report describes a study that used electromagnetic surveys to provide this information. In the first phase of the study, electromagnetic soundings were made using time-domain and frequency-domain electro- magnetic methods. On the basis of these initial results, the time- domain method was judged ineffective because of cultural noise in the study area, so subsequent surveys were made using the frequency-domain method. For the second phase of the study, 31 frequency-domain electromagnetic surveys were conducted along the inner valley and parallel to the Rio Grande in the Albuquerque area in the spring and summer of 1997 to determine the presence of hydrologically significant clay-rich layers buried in the inner-valley alluvium. For this report, the 31 survey sections were combined into 10 composite sections for ease of interpretation. Terrain-conductivity data from the surveys were modeled using interpretation software to produce geoelectric cross sections along the survey lines. This modeling used lithologic logs from two wells installed near the survey lines: the Bosque South and Rio Bravo 5 wells. Because of cultural interference, location of the wells and soundings, complex stratigraphy, and difficulty interpreting lithology, such interpretation was inconclusive. Instead, a decision process based on modeling results was developed using vertical and horizontal dipole 40-meter intercoil spacing terrain-conductivity values. Values larger than or equal to 20 millisiemens per meter were interpreted to contain a hydrologically significant thickness of clay-rich sediment. Thus, clay-rich sediment was interpreted to underlie seven segments of the 10 composited survey lines, totaling at least 2,660 meters of the Rio Grande inner valley. The longest of these clay

Advanced data processing of airborne electromagnetic data for imaging hidden conduit networks in the coastal karst plain of Tulum (Mexico); Tecnicas avanzadas de analisis de datos electromagneticos aerotransportados para cartografia de redes de conductos karsticos de la planicie costera de Tulum (Mexico)

Energy Technology Data Exchange (ETDEWEB)

Schiller, A.; Schattauer, I.; Ottowitz, D.

2016-07-01

This study is part of a series of international research cooperations which commenced in 2007 and are still ongoing. The study area is located on the east coast of the Yucatan Peninsula, Mexico, and comprises the northern most part of the Sian Kaan biosphere reserve, a coastal wetland of international importance, as well as the city of Tulum in the state of Quintana Roo, and part of the second largest barrier reef in the world some 300 metres to one kilometre off shore. Two airborne surveys, conducted in 2007 and 2008 by the Geological Survey of Austria, covered an area of some 200 square kilometres, including the well-known Ox Bel Ha cave system, already mapped by exploration divers. In order to get additional ground truth data and input for the hydrological model, extended ground geophysical campaigns have been conducted an - nually. The first processing of the airborne electromagnetic (AEM) data revealed not only a clear signature from known caves but also the image of a vast, unexplored, hidden conduit network. However, lateral and depth resolution was limited due to measurement drift and noise as well the specific behaviour of the ap - plied inversion technique. Newly developed algorithms for processing AEM data and inversion results have improved the signal-to-noise ratio significantly and enabled the imaging of well defined structures in the underground. Therefore, the AEM method is now capable of quickly deliver crucial structural information of karst-water regimes in difficult accessible areas with unique depth information compared to previous studies. (Author)

Airborne gamma-ray spectrometer and magnetometer survey: Aberdeen quadrangle, South Dakota. Final report

International Nuclear Information System (INIS)

1981-04-01

During the months of June through October, 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. This report discusses the results obtained over the Aberdeen, South Dakota map area. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps, flight path maps, and computer printer maps

DATA ACQUISITION AND APPLICATIONS OF SIDE-LOOKING AIRBORNE RADAR IN THE U. S. GEOLOGICAL SURVEY.

Science.gov (United States)

Jones, John Edwin; Kover, Allan N.

1985-01-01

The Side-Looking Airborne Radar (SLAR) program encompasses a multi-discipline effort involving geologists, hydrologists, engineers, geographers, and cartographers of the U. S. Geological Survey (USGS). Since the program began in 1980, more than 520,000 square miles of aerial coverage of SLAR data in the conterminous United States and Alaska have been acquired or contracted for acquisition. The Geological Survey has supported more than 60 research and applications projects addressing the use of this technology in the earth sciences since 1980. These projects have included preparation of lithographic reproductions of SLAR mosaics, research to improve the cartographic uses of SLAR, research for use of SLAR in assessing earth hazards, and studies using SLAR for energy and mineral exploration through improved geologic mapping.

Airborne gamma-ray spectrometer and magnetometer survey, Point Lay Quadrangle, Alaska. Volume I. Final report

International Nuclear Information System (INIS)

1981-02-01

The results obtained from an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over the Point Lay map area of Alaska are presented. Based on the criteria outlined in the general section on interpretation, a total of six uranium anomalies have been indicated on the interpretation map. All six are only weakly to moderately anomalous in either uranium or the uranium ratios. None of these are thought to be of any economic significance. No follow-up work is recommended for the Point Lay Quadrangle

Airborne gamma-ray spectrometer and magnetometer survey: Harrison Bay Quadrangle, Alaska. Final report, Volume 1

International Nuclear Information System (INIS)

1981-02-01

During the months of July and August of 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 3 0 x 1 0 and one (1) 4 0 x 1 0 NTMS quadrangles of the Alaska North Slope. These include the Barrow, Wainwright, Meade River, Teshekpuk, Harrison Bay, Beechey Point, Point Lay, Utukok River, Lookout Ridge, Ikpikpuk River, Umiat, and Sagavanirktok quadrangles. This report discusses the results obtained over the Harrison Bay map area

Classical electromagnetic radiation

CERN Document Server

Heald, Mark A

2012-01-01

Newly corrected, this highly acclaimed text is suitable for advanced physics courses. The author presents a very accessible macroscopic view of classical electromagnetics that emphasizes integrating electromagnetic theory with physical optics. The survey follows the historical development of physics, culminating in the use of four-vector relativity to fully integrate electricity with magnetism.

Airborne gamma-ray spectrometer and magnetometer survey Coos Bay, Oregon. Final report

International Nuclear Information System (INIS)

1981-05-01

During the months of August, September, and October of 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over ten (10) areas over northern California and southwestern Oregon. These include the 2 0 x 1 0 NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1 0 x 2 0 areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Coos Bay, Oregon, map area. Line spacing was generally six miles for east/west traverses and eighteen miles for north/south tie lines over the northern one-half of the area. Traverses and tie lines were flown at three miles and twelve miles respectively over the southern one-half of the area. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 863.8 line miles are in this quadrangle

Airborne gamma-ray spectrometer and magnetometer survey: Alturas quadrangle, California. Final report

International Nuclear Information System (INIS)

1981-05-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over ten (10) areas over northern California and southwestern Oregon. These include the 2 0 x 1 0 NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1 0 x 2 0 areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Alturas, California, map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately eighteen (18) miles apart. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1631.6 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

Airborne gamma-ray spectrometer and magnetometer survey: Susanville quadrangle, California. Final report

International Nuclear Information System (INIS)

1981-05-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over ten (10) areas over northern California and southwestern Oregon. These include the 2 0 x 1 0 NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1 0 x 2 0 areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Susanville, California, map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately eighteen (18) miles apart. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1642.8 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

Determination of data correction coefficients and the sensitivities of the KIER air-borne gamma-ray spectrometer survey system

International Nuclear Information System (INIS)

Koo, J.H.; Cho, D.H.; Park, Y.S.

1982-01-01

In air-borne gamma-ray spectrometer survey, the observed data must be corrected for the background, Compton scattering and flight altitude. And the corrected data are usually converted into the radiometric elements equivalents of the ground, using the sensitivities of the survey system. Accordingly, the correction coefficients and the sensitivities are determined as follows for the KIER air-borne survey system. The stripping or Compton scattering coefficients α, β and γ at the ground level were first determined on the basis of the gamma-ray count rates due to the 5 concrete calibration pads of the Soosaek Airbase, together with the radiometric elements concentrations of the core samples taken from the pads. As for the determination of the exponential altitude coefficients anti μ(K), anti μ(U), anti μ(Th) and anti μ(Tc), the count rates observed over the Hongseong Test Strip of about 3 km length were used after they had been corrected for the background and Compton scattering. The background count rates mainly caused by the air-craft as well as cosmic radiations were determined with the data taken over the West Sea near Anmyon Island, Chung-cheongnam-do. And the corrected count rates observed over the Strip, combined with the average radiometric elements concentrations of the Strip, yielded the sensitivities k(K), k(U) and k(Th) at the 400 feet flight altitude. (author)

Contouring algorithm for two dimensional data- an application to airborne surveys

International Nuclear Information System (INIS)

Suryakumar, N.V.; Rohatgi, Savita; Raghuwanshi, S.S.

1994-01-01

The paper describes in general the contouring algorithm for two dimensional projection of aeroradiometric data and considers not only irregularly spaced flight lines but also solves the other problems related to voluminous data acquired during the airborne surveys. Several simple logics have been described for drawing the contours using scan method and taking care of annotations, identification marking, geographical locations, map size, contour density for visual distinctness and many such problems which may arise during contouring. The present paper also discusses various possibilities of contour line segments in the mini-grid and the criterion for selection of suitable segments has been described in detail. A novel approach to avoid the crossing of contours or missing data is also briefly discussed. The simplicity of the algorithm is mentioned for its ready implementation or any computer/plotter. (author). 8 refs., 8 figs

Feasibility study for an airborne high-sensitivity gamma-ray survey of Alaska. Phase II (final) report: 1976--1979 program

International Nuclear Information System (INIS)

1975-01-01

This study constitutes a determination of the extent to which it is feasible to use airborne, high-sensitivity gamma spectrometer systems for uranium reconnaissance in the State of Alaska, and specification of a preliminary plan for surveying the entire state of the 1975--1979 time frame. Phase I included the design of a program to survey the highest priority areas in 1975 using available aircraft and spectrometer equipment. This has now resulted in a contract for 10,305 flight line miles to cover about 11 of the 1:250,000 scale quadrangles using a DC-3 aircraft with an average 6.25 x 25 mile grid of flight line. Phase II includes the design of alternative programs to cover the remaining 128 quadrangles using either a DC-3 and a Bell 205A helicopter or a Helio Stallion STOL aircraft and a Bell 205A helicopter during 1976-1979. The 1976-1979 time frame allows some time for possible new system developments in both airborne gamma-ray spectrometers and in ancillary equipment, and these are outlined. (auth)

Induced polarization and electromagnetic field surveys of sedimentary uranium deposits

International Nuclear Information System (INIS)

Campbell, D.L.; Smith, B.D.

1985-01-01

Induced polarization (IP) and electromagnetic (EM) geophysical surveys were made over three areas of sedimentary uranium deposits in the western United States. The EM techniques were sometimes useful for investigating general structural settings, but not for finding uranium deposits per se. IP techniques were useful to help pinpoint zones of disseminated pyrite associated with the uranium deposits. In one case no clear differences were seen between the IP signatures of oxidized and reduced ground. Spectral (multi-frequency) IP showed no particular advantages over conventional IP for exploration applications. A sediment mineralization factor is introduced comparable to the ''metal factor'' used to detect porphyry copper mineralization. (author)

Airborne Detection of Cosmic-Ray Albedo Neutrons for Regional-Scale Surveys of Root-Zone Soil Water on Earth

Science.gov (United States)

Schrön, M.; Bannehr, L.; Köhli, M.; Zreda, M. G.; Weimar, J.; Zacharias, S.; Oswald, S. E.; Bumberger, J.; Samaniego, L. E.; Schmidt, U.; Zieger, P.; Dietrich, P.

2017-12-01

While the detection of albedo neutrons from cosmic rays became a standard method in planetary space science, airborne neutron sensing has never been conceived for hydrological research on Earth. We assessed the applicability of atmospheric neutrons to sense root-zone soil moisture averaged over tens of hectares using neutron detectors on an airborne vehicle. Large-scale quantification of near-surface water content is an urgent challenge in hydrology. Information about soil and plant water is crucial to accurately assess the risks for floods and droughts, to adjust regional weather forecasts, and to calibrate and validate the corresponding models. However, there is a lack of data at scales relevant for these applications. Most conventional ground-based geophysical instruments provide root-zone soil moisture only within a few tens of m2, while electromagnetic signals from conventional remote-sensing instruments can only penetrate the first few centimeters below surface, though at larger spatial areas.In the last couple of years, stationary and roving neutron detectors have been used to sense the albedo component of cosmic-ray neutrons, which represents the average water content within 10—15 hectares and 10—50 cm depth. However, the application of these instruments is limited by inaccessible terrain and interfering local effects from roads. To overcome these limitations, we have pioneered first simulations and experiments of such sensors in the field of airborne geophysics. Theoretical investigations have shown that the footprint increases substantially with height above ground, while local effects smooth out throughout the whole area. Campaigns with neutron detectors mounted on a lightweight gyrocopter have been conducted over areas of various landuse types including agricultural fields, urban areas, forests, flood plains, and lakes. The neutron signal showed influence of soil moisture patterns in heights of up to 180 m above ground. We found correlation with

Airborne gamma-ray spectrometer and magnetometer survey, New Rockford Quadrangle, North Dakota. Final report

International Nuclear Information System (INIS)

1981-04-01

An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the New Rockford map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1397 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey at Vanna, Karlsoey

International Nuclear Information System (INIS)

Rodionov, Alexei; Ofstad, Frode

2012-01-01

NGU conducted an airborne geophysical survey in Vanna area in June 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 1336 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 27 degrees NW and average speed 106 km/h. The average terrain clearance of the bird was 59 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both -automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for four frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000. (Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey at Vanna, Karlsoey

Energy Technology Data Exchange (ETDEWEB)

Rodionov, Alexei; Ofstad, Frode

2012-07-01

NGU conducted an airborne geophysical survey in Vanna area in June 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 1336 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 27 degrees NW and average speed 106 km/h. The average terrain clearance of the bird was 59 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both -automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for four frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000. (Author)

Helicopter electromagnetic survey of the Model Land Area, Southeastern Miami-Dade County, Florida

Science.gov (United States)

Fitterman, David V.; Deszcz-Pan, Maria; Prinos, Scott T.

2012-01-01

This report describes a helicopter electromagnetic survey flown over the Model Land Area in southeastern Miami-Dade County, Florida, to map saltwater intrusion in the Biscayne aquifer. The survey, which is located south and east of Florida City, Florida, covers an area of 115 square kilometers with a flight-line spacing of 400 meters. A five-frequency, horizontal, coplanar bird with frequencies ranging from 400 to 100,000 Hertz was used. The data were interpreted using differential resistivity analysis and inversion to produce cross sections and resistivity depth-slice maps. The depth of investigation is as deep as 100 meters in freshwater-saturated portions of the Biscayne aquifer and the depth diminishes to about 50 meters in areas that are intruded by saltwater. The results compare favorably with ground-based, time-domain electromagnetic soundings and induction logs from observation wells in the area. The base of a high-resistivity, freshwater-saturated zone mapped in the northern 2 kilometers of the survey area corresponds quite well with the base of the surficial aquifer that has been determined by drilling. In general, saltwater in the survey area extends 9 to 12 kilometers inland from the coast; however, there is a long nose of saltwater centered along the Card Sound Road Canal that extends 15 kilometers inland. The cause of this preferential intrusion is likely due to uncontrolled surface flow along the canal and subsequent leakage of saltwater into the aquifer. Saltwater also extends farther inland in the area between U.S. Highway 1 and Card Sound Road than it does to the west of this area. Until 1944, a railroad grade occupied the current location of U.S. Highway 1. Borrow ditches associated with the railroad grade connected to Barnes Sound and allowed saltwater to flow during droughts and storm surges to within a few kilometers of Florida City. Relicts of this saltwater that settled to the bottom of the Biscayne aquifer can be seen in the helicopter

The Effect of Pitch, Roll, and Yaw on Airborne Gravity Observations of the NOAA GRAV-D Project

Science.gov (United States)

Childers, V. A.; Kanney, J.; Youngman, M.

2017-12-01

Aircraft turbulence can wreak havoc on the gravity measurementby beam-style gravimeters. Prior studies have confirmed the correlation of poor quality airborne gravity data collection to amplified aircraft motion. Motion in the aircraft is the combined effect of the airframe design, the autopilot and its performance, and the weather/wind regime. NOAA's National Geodetic Survey has launched the Gravity for the Redefinition of the American Vertical Datum project (GRAV-D) to provide the foundation for a new national vertical datum by 2022. This project requires collecting airborne gravity data covering the entire country and its holdings. The motion of the aircraft employed in this project is of prime importance because we use a beam-style gravimeter mounted on a gyro-stabilized platform to align the sensor to a time-averaged local vertical. Aircraft turbulence will tend to drive the platform off-level, allowing horizontal forces to map into the vertical gravity measurement. Recently, the GRAV-D project has experimented with two new factors in airborne gravity data collection. The first aspect is the use of the Aurora optionally piloted Centaur aircraft. This aircraft can be flown either with or without a pilot, but the autopilot is specifically designed to be very accurate. Incorporated into the much smaller frame of this aircraft is a new gravimeter developed by Micro-g LaCoste, called the Turnkey Airborne Gravimeter System 7 (TAGS7). This smaller, lighter instrument also has a new design whereby the beam is held fixed in an electromagnetic force field. The result of this new configuration is notably improved data quality in wind conditions higher than can be tolerated by our current system. So, which caused the improvement, the aircraft motion or the new meter? This study will start to tease apart these two effects with recently collected survey data. Specifically, we will compare the motion profile of the Centaur aircraft with other aircraft in the GRAV-D portfolio

Airborne systems for emergency radiological monitoring

International Nuclear Information System (INIS)

Jupiter, C.; Boyns, P.

1976-01-01

A variety of aerial radiological monitoring systems are available to respond to a radiological accident or incident affecting large areas. These are operated by EG and G, Inc. for ERDA's Division of Operational Safety. A survey system can be airborne within approximately two hours after notification. Both airborne and terrestrial radioactivity can be measured and mapped. Special analysis procedures allow discrimination between radioactivity from most man-made radioelements and naturally occurring radioelements. A position accuracy of +-54 feet can be maintained over a large area survey. Detection sensitivity for gamma sources employing NaI detector arrays on board an airplane flying at 500 feet altitude is better than 2 μR/hr for surface planar contaminants and approximately 10 mCi for a point gamma source

Use of a superconductive gradiometer in an ultrasensitive electromagnetic metal detector

International Nuclear Information System (INIS)

Czipott, P.V.; Podney, W.N.

1989-01-01

The authors present a new instrument that we call an electromagnetic gradiometer. It uses a SQUID sensor as the receiver in an active, electromagnetic detector of nonferrous as well as ferrous objects. The gradiometer pickup loops sit in the center of magnet coils that generate a time-varying magnetic field inducing eddy currents in conductive bodies. The gradiometer measures the secondary magnetic field of the eddy currents. The SQUID's sensitivity at frequencies below 1 kHz makes electromagnetic metal detectors practical in the marine environment, where the electrical conductivity of seawater precludes conventional systems. The authors describe a prototype system that attains a detection range of 10 m in seawater for targets 50 cm in diameter. It operates at frequencies from 1 Hz to a few hundred Hz. Uses of the electromagnetic gradiometer include locating naval mines and undersea treasure. The system's response to seawater enables application to airborne electromagnetic bathymetry. On land, its sensitivity to crustal conductivity contrasts suits it to mineral exploration

Airborne Gamma-Ray Survey in Latvia 1995/96

DEFF Research Database (Denmark)

Bargholz, Kim

1998-01-01

Based on Airborne Gamma-Ray Spectrometry measurements performed with the Danish AGS equipment in 1995 and 1996 maps of the natural radioactivity have been produdced for selected areas in Latvia. The calibration of the quipment have been improved by comparisons with soil sample measurements....

Nuclear assay of coal. Volume 4. Moisture determination in coal: survey of electromagnetic techniques. Final report

International Nuclear Information System (INIS)

Bevan, R.; Luckie, P.; Gozani, T.; Brown, D.R.; Bozorgmanesh, H.; Elias, E.

1979-01-01

This survey consists of two basic parts. The first consists of a survey of various non-nuclear moisture determination techniques. Three techniques are identified as promising for eventual on-line application with coal; these are the capacitance, microwave attenuation, and nuclear magnetic resonance (NMR) techniques. The second part is devoted to an in-depth analysis of these three techniques and the current extent to which they have been applied to coal. With a given coal type, accuracies of +- 1% absolute in moisture content are achievable with all three techniques. The accuracy of the two electromagnetic techniques has been demonstrated in the laboratory and on-line in coal burning plants, whereas only small samples have been analyzed with NMR. The current shortcoming of the simple electromagnetic techniques is the sensitivity of calibrations to physical parameters and coal type. NMR is currently limited by small sample sizes and non-rugged design. These findings are summarized and a list of manufacturers of moisture analyzers is given in the Appendix

Workflow with pitfalls to derive a regional airborne magnetic compilation

Science.gov (United States)

Brönner, Marco; Baykiev, Eldar; Ebbing, Jörg

2017-04-01

Today, large scale magnetic maps are usually a patchwork of different airborne surveys from different size, different resolution and different years. Airborne magnetic acquisition is a fast and economic method to map and gain geological and tectonic information for large areas, onshore and offshore. Depending on the aim of a survey, acquisition parameters like altitude and profile distance are usually adjusted to match the purpose of investigation. The subsequent data processing commonly follows a standardized workflow comprising core-field subtraction and line leveling to yield a coherent crustal field magnetic grid for a survey area. The resulting data makes it possible to correlate with geological and tectonic features in the subsurface, which is of importance for e.g. oil and mineral exploration. Crustal scale magnetic interpretation and modeling demand regional compilation of magnetic data and the merger of adjacent magnetic surveys. These studies not only focus on shallower sources, reflected by short to intermediate magnetic wavelength anomalies, but also have a particular interest in the long wavelength deriving from deep seated sources. However, whilst the workflow to produce such a merger is supported by quite a few powerful routines, the resulting compilation contains several pitfalls and limitations, which were discussed before, but still are very little recognized. The maximum wavelength that can be resolved of each individual survey is directly related to the survey size and consequently a merger will contribute erroneous long-wavelength components in the magnetic data compilation. To minimize this problem and to homogenous the longer wavelengths, a first order approach is the combination of airborne and satellite magnetic data commonly combined with the compilation from airborne data, which is sufficient only under particular preconditions. A more advanced approach considers the gap in frequencies between airborne and satellite data, which motivated

Airborne laser altimetry survey of Glaciar Tyndall, Patagonia

DEFF Research Database (Denmark)

Keller, K.; Casassa, G.; Rivera, A.

2007-01-01

The first airborne laser altimetry measurements of a glacier in South America are presented. Data were collected in November of 2001 over Glaciar Tyndall, Torres del Paine National Park, Chilean Patagonia, onboard a Twin Otter airplane of the Chilean Air Force. A laser scanner with a rotating...

Data processing of remotely sensed airborne hyperspectral data using the Airborne Processing Library (APL): Geocorrection algorithm descriptions and spatial accuracy assessment

Science.gov (United States)

Warren, Mark A.; Taylor, Benjamin H.; Grant, Michael G.; Shutler, Jamie D.

2014-03-01

Remote sensing airborne hyperspectral data are routinely used for applications including algorithm development for satellite sensors, environmental monitoring and atmospheric studies. Single flight lines of airborne hyperspectral data are often in the region of tens of gigabytes in size. This means that a single aircraft can collect terabytes of remotely sensed hyperspectral data during a single year. Before these data can be used for scientific analyses, they need to be radiometrically calibrated, synchronised with the aircraft's position and attitude and then geocorrected. To enable efficient processing of these large datasets the UK Airborne Research and Survey Facility has recently developed a software suite, the Airborne Processing Library (APL), for processing airborne hyperspectral data acquired from the Specim AISA Eagle and Hawk instruments. The APL toolbox allows users to radiometrically calibrate, geocorrect, reproject and resample airborne data. Each stage of the toolbox outputs data in the common Band Interleaved Lines (BILs) format, which allows its integration with other standard remote sensing software packages. APL was developed to be user-friendly and suitable for use on a workstation PC as well as for the automated processing of the facility; to this end APL can be used under both Windows and Linux environments on a single desktop machine or through a Grid engine. A graphical user interface also exists. In this paper we describe the Airborne Processing Library software, its algorithms and approach. We present example results from using APL with an AISA Eagle sensor and we assess its spatial accuracy using data from multiple flight lines collected during a campaign in 2008 together with in situ surveyed ground control points.

Airborne gamma-ray spectrometer and magnetometer survey, Devils Lake quadrangle, North Dakota. Final report

International Nuclear Information System (INIS)

1981-05-01

During the months of June through October, 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. This report discusses the results obtained over the Devil's Lake map area of North Dakota. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps, flight path maps, and computer printer maps

New approach to airborne monitoring of radioactive pollution

International Nuclear Information System (INIS)

Hoeschl, V.; Jurza, P.; Pavlik, B.

1997-01-01

The use of remote sensing methods in the monitoring of an environment is increasing. The best results are obtained when various types of exploration methods are available. This paper presents the use of airborne gamma ray methods, which can be included in a wide scope of works related to environmental problems. It may concern uranium mining areas, areas surrounding various nuclear facilities or areas of Chernobyl fallout. Gamma ray spectrometry data can be combined with airborne magnetic, surface gravity and satellite imagery data to obtain maximum information in data output. Airborne geophysics is able to detect and delineate radioactive contamination and to find important geological trends defining the geological structure of the monitored area. Our company PICODAS Prague Ltd. introduces new sophisticated airborne instrumentation as well as up-to-date data processing and data presentation techniques. In the Czech Cretaceous, a long term project, ''The Structurally-tectonic Survey of the South-West Foreland of the Straz Deposit'' has been undertaken, concerning the ecological load on the environment, especially the pollution of the underground water level horizons due to uranium mining in that area. The major interest is the complicated tectonic structure which interferes heavily with the hydrogeological situation of the region. The paper presents the results of airborne surveys and the interpretation of other geophysical data from the surroundings of Straz pod Ralskem and from Karlovy Vary. (author)

Airborne gamma-ray spectrometer and magnetometer survey: Peoria, Decater, Belleville Quadrangles, (IL). Final report

International Nuclear Information System (INIS)

1981-01-01

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Peoria, Decatur, and Belleville, 1:250,000 National Topographic Map Series (NTMS), quadrangle maps. The survey was part of DOE's National Uranium Resource Evaluation (NURE) program. Data were collected by a helicopter equipped with a gamma-ray spectrometer with a large crystal volume, and with a high sensitivity proton procession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test Range. Data quality was ensured during the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. The anomalies were interpreted and an interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data collection procedures, the data processing procedures, the data presentation, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

Airborne EM, Lithology and in-situ Data Used for Quantizing Groundwater Salinity in Zeeland (NL)

Science.gov (United States)

Meyer, U.; Siemon, B.; van Baaren, E.; Dabekaussen, W.; Delsman, J. R.; Karaoulis, M.; Gunnink, J.; Pauw, P.; Vermaas, T.

2017-12-01

In a setting of predominantly saline surface waters in Zeeland, the Netherlands, the only available shallow fresh groundwater is present in the form of freshwater lenses floating on top of the saline groundwater. This fresh water is vital for agricultural, industrial, ecological, water conservation and drinking water functions. An essential first step for managing the usable water properly is to know the present spatial fresh-brackish-saline groundwater distribution. As traditional salinity monitoring is labor-intensive, airborne electromagnetics, which is fast and can cover large areas in short time, is an efficient alternative. A consortium of BGR, Deltares and TNO conducted FRESHEM Zeeland (FREsh Salt groundwater distribution by Helicopter ElectroMagnetic survey in the Province of Zeeland) in 2014-17. An area of more than 2000 square km was surveyed using BGR's helicopter-borne geophysical system totaling to about 9,600 line-km. The HEM data, after inversion to 2.5 Million resistivity-depth models for each of the three 1D inversion procedures applied (Marquardt single site, smooth and sharp laterally constrained inversion), served as base-line information for further interpretation. A probabilistic Monte Carlo approach combines HEM resistivities, 3D lithology model data (GeoTOP), laboratory results (formation factor and surface conductivity) and local in-situ groundwater measurements for the translation of resistivity to Chloride concentration. The resulting 3D voxel model enables stakeholders to implement spatial Chloride concentration in their groundwater models.

Interpreting Electromagnetic Reflections In Glaciology

Science.gov (United States)

Eisen, O.; Nixdorf, U.; Wilhelms, F.; Steinhage, D.; Miller, H.

Electromagnetic reflection (EMR) measurements are active remote sensing methods that have become a major tool for glaciological investigations. Although the basic pro- cesses are well understood, the unambiguous interpretation of EMR data, especially internal layering, still requires further information. The Antacrtic ice sheet provides a unique setting for investigating the relation between physical­chemical properties of ice and EMR data. Cold ice, smooth surface topography, and low accumulation facilitates matters to use low energy ground penetrating radar (GPR) devices to pene- trate several tens to hundreds of meters of ice, covering several thousands of years of snow deposition history. Thus, sufficient internal layers, primarily of volcanic origin, are recorded to enable studies on a local and regional scale. Based on dated ice core records, GPR measurements at various frequencies, and airborne radio-echo sound- ing (RES) from Dronning Maud Land (DML), Antarctica, combined with numerical modeling techniques, we investigate the influence of internal layering characteristics and properties of the propagating electromagnetic wave on EMR data.

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Mauken, Maalselv, Troms

International Nuclear Information System (INIS)

Rodionov, Alexei; Koziel, Janusz; Lynum, Rolf

2012-01-01

NGU conducted an airborne geophysical survey in Mauken area in June 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 3680 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 33 degrees NE and average speed 88km/h. The average terrain clearance of the bird was 45m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both -automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000. (Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Mauken, Maalselv, Troms

Energy Technology Data Exchange (ETDEWEB)

Rodionov, Alexei; Koziel, Janusz; Lynum, Rolf

2012-07-01

NGU conducted an airborne geophysical survey in Mauken area in June 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 3680 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 33 degrees NE and average speed 88km/h. The average terrain clearance of the bird was 45m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both -automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000. (Author)

Planning a radar system for protection from the airborne threat

International Nuclear Information System (INIS)

Greneker, E.F.; McGee, M.C.

1986-01-01

A planning methodology for developing a radar system to protect nuclear materials facilities from the airborne threat is presented. Planning for physical security to counter the airborne threat is becoming even more important because hostile acts by terrorists are increasing and airborne platforms that can be used to bypass physical barriers are readily available. The comprehensive system planning process includes threat and facility surveys, defense hardening, analysis of detection and early warning requirements, optimization of sensor mix and placement, and system implementation considerations

New efforts using helicopter-borne and ground based electromagnetics for mineral exploration

Science.gov (United States)

Meyer, U.; Siemon, B.; Noell, U.; Gutzmer, J.; Spitzer, K.; Becken, M.

2014-12-01

Throughout the last decades mineral resources, especially rare earth elements, gained a steadily growing importance in industry and therefore as well in exploration. New targets for mineral investigations came into focus and known sources have been and will be revisited. Since most of the mining for mineral resources in the past took place in the upper hundred metres below surface new techniques made deeper mining economically feasible. Consequently, mining engineers need the best possible knowledge about the full spatial extent of prospective geological structures, including their maximum depths. Especially in Germany and Europe, politics changed in terms not to rely only on the global mineral trade market but on national resources, if available. BGR and partners therefore started research programs on different levels to evaluate and develop new technologies on environmental friendly, non-invasive spatial exploration using airborne and partly ground-based electromagnetic methods. Mining waste heaps have been explored for valuable residual minerals (research project ROBEHA), a promising tin bearing ore body is being explored by airborne electromagnetics (research project E3) and a new airborne technology is aimed at to be able to reach investigation depths of about 1 km (research project DESMEX). First results of the projects ROBEHA and E3 will be presented and the project layout of DESMEX will be discussed.

Effects of Atmospheric Refraction on an Airborne Weather Radar Detection and Correction Method

Directory of Open Access Journals (Sweden)

Lei Wang

2015-01-01

Full Text Available This study investigates the effect of atmospheric refraction, affected by temperature, atmospheric pressure, and humidity, on airborne weather radar beam paths. Using three types of typical atmospheric background sounding data, we established a simulation model for an actual transmission path and a fitted correction path of an airborne weather radar beam during airplane take-offs and landings based on initial flight parameters and X-band airborne phased-array weather radar parameters. Errors in an ideal electromagnetic beam propagation path are much greater than those of a fitted path when atmospheric refraction is not considered. The rates of change in the atmospheric refraction index differ with weather conditions and the radar detection angles differ during airplane take-off and landing. Therefore, the airborne radar detection path must be revised in real time according to the specific sounding data and flight parameters. However, an error analysis indicates that a direct linear-fitting method produces significant errors in a negatively refractive atmosphere; a piecewise-fitting method can be adopted to revise the paths according to the actual atmospheric structure. This study provides researchers and practitioners in the aeronautics and astronautics field with updated information regarding the effect of atmospheric refraction on airborne weather radar detection and correction methods.

Evaluating natural radiation level by existing airborne radioactive data

International Nuclear Information System (INIS)

Mingkao, Hu; Changqing, Han; Jiangqi, Fang; Zhengxin, Shen

2002-01-01

Airborne Survey and Remote Sensing Center of Nuclear Industry, founded in the middle of 1950s, is a unique unit specialized in uranium exploration by airborne radioactive survey in China. Large numbers of airborne data of radioactivity and abundant experience have been accumulated for more than 40 years. All-round detailed investigation of environmental radiation levels in our country will not be completed in the near future. Thus, at present it is considered to evaluate natural radiation levels using the existing radioactive data. This paper introduces the results of analysis and study comparing airborne radioactive data for radiation environmental evaluation obtained from survey area in Gansu, China, in the 2001 with the measurement results by ground gamma ray radiation dose-rate instrument for environment. The air-earth inter-comparison error does not exceed 30% at radiation fields with a definite area, and the air-earth inter-comparison error does not exceed 60% at outcrop of granite. In 6km long profile that has various circumstances, such as desert, Gobi, farmland and residential area, minimum of air absorbed dose rate is 47nGy/h at an altitude of 1 meter above the soil plane, maximum is 68nGy/h. The inter-comparison errors are usually less than 20%, and maximum is 25.38%. This shows that it is feasible to obtain natural radiation levels rapidly if we could use the existing radioactive data adequately and make some correction, such as geology factor

Precise Detection of Buried Underground Utilities by Non-destructive Electromagnetic Survey

International Nuclear Information System (INIS)

Shon, Ho Woong; Lee, Seung Hee; Lee, Kang Won

2002-01-01

To detect the position and depth of buried underground utilities, method of Ground Penetrating Radar(GPR) survey is the most commonly used. However, the skin-depth of GPR is very shallow, and in the places where subsurface materials are not homogeneous and are compose of clays and/or salts and gravels, GPR method has limitations in application and interpretation. The aim of this study is to overcome these limitations of GPR survey. For this purpose the site where the GPR survey is unsuccessful to detect the underground big pipes is selected, and soil tests were conducted to confirm the reason why GPR method was not applicable. Non-destructive high-frequency electromagnetic (HFEM) survey was newly developed and was applied in the study area to prove the effectiveness of this new technique. The frequency ranges 2kHz∼4MHz and the skin depth is about 30m. The HFEM measures the electric field and magnetic field perpendicular to each other to get the impedance from which vertical electric resistivity distribution at the measured point can be deduced. By adopting the capacitive coupled electrodes, it can make the measuring time shorter, and can be applied to the places covered by asphalt an and/or concrete. In addition to the above mentioned advantages, noise due to high-voltage power line is much reduced by stacking the signals. As a result, the HFEM was successful in detecting the buried underground objects. Therefore this method is a promising new technique that can be applied in the lots of fields, such as geotechnical and archaeological surveys

Combining ground-based and airborne EM through Artificial Neural Networks for modelling glacial till under saline groundwater conditions

DEFF Research Database (Denmark)

Gunnink, J.L.; Bosch, A.; Siemon, B.

2012-01-01

Airborne electromagnetic (AEM) methods supply data over large areas in a cost-effective way. We used ArtificialNeural Networks (ANN) to classify the geophysical signal into a meaningful geological parameter. By using examples of known relations between ground-based geophysical data (in this case...... electrical conductivity, EC, from electrical cone penetration tests) and geological parameters (presence of glacial till), we extracted learning rules that could be applied to map the presence of a glacial till using the EC profiles from the airborne EM data. The saline groundwater in the area was obscuring...

Airborne gamma ray spectrometry in certain areas of the Islamic Republic of Iran and its results - correlation to the other usages

International Nuclear Information System (INIS)

Soleimani, G.; Yegani, F.S.

1997-01-01

Airborne survey can be utilized as a multipurpose data in different fields such as exploration, health physics, environmental studies and so on. The well known advantages of airborne survey include rapidity, more extent of surveyed area, the possibility of application in unaccessible regions where no other methods can be utilized. More than one third of Iran territory i.e. about 600,000 km 2 has been surveyed by magnetic and spectral gamma ray airborne. This survey is one of the largest and most highly specified survey of its type ever attempted. Extremely large quantities of data were generated during the survey which can be used as a baseline information. (author)

FRESHEM - Fresh-saline groundwater distribution in Zeeland (NL) derived from airborne EM

Science.gov (United States)

Siemon, Bernhard; van Baaren, Esther; Dabekaussen, Willem; Delsman, Joost; Gunnik, Jan; Karaoulis, Marios; de Louw, Perry; Oude Essink, Gualbert; Pauw, Pieter; Steuer, Annika; Meyer, Uwe

2017-04-01

In a setting of predominantly saline surface waters, the availability of fresh water for agricultural purposes is not obvious in Zeeland, The Netherlands. Canals and ditches are mainly brackish to saline due to saline seepage, which originates from old marine deposits and salt-water transgressions during historical times. The only available fresh groundwater is present in the form of freshwater lenses floating on top of the saline groundwater. This fresh groundwater is vital for agricultural, industrial, ecological, water conservation and drinking water functions. An essential first step for managing this fresh groundwater properly is to know the present spatial fresh-brackish-saline groundwater distribution. As traditional salinity monitoring is labour-intensive, airborne electromagnetics (AEM), which is fast and can cover large areas in short time, is an efficient alternative. A consortium of BGR, Deltares and TNO started FRESHEM Zeeland (FREsh Salt groundwater distribution by Helicopter ElectroMagnetic survey in the Province of Zeeland) in October 2014. Within 3x2 weeks of the first project year, the entire area of about 2000 km2 was surveyed using BGR's helicopter-borne geophysical system totalling to about 10,000 line-km. The HEM datasets of 17 subareas were carefully processed using advanced BGR in-house software and inverted to 2.5 Million resistivity-depth models. Ground truthing demonstrated that the large-scale HEM results fit very well with small-scale ground EM data (ECPT). Based on this spatial resistivity distribution, a 3D voxel model for Chloride concentration was derived for the entire province taking into account geological model data (GeoTOP) for the lithology correction and local in-situ groundwater measurements for the translation of water conductivity to Chloride concentration. The 3D voxel model enables stakeholders to implement spatial Chloride concentration in their groundwater models.

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Finnsnes area, Lenvik, Troms

International Nuclear Information System (INIS)

Rodionov, Alexei; Ofstad, Frode; Tassis, Georgios

2012-01-01

NGU conducted an airborne geophysical survey in Finnsnes area in July - August 2012. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 2715 line km. The Geotech Ltd. Hummingbird frequency domain EM system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 120 degrees NW-SE with the average speed 89 km/h. The average terrain clearance of the bird was 55 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was levelled and filtered. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000.(Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Finnsnes area, Lenvik, Troms

Energy Technology Data Exchange (ETDEWEB)

Rodionov, Alexei; Ofstad, Frode; Tassis, Georgios

2012-07-01

NGU conducted an airborne geophysical survey in Finnsnes area in July - August 2012. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 2715 line km. The Geotech Ltd. Hummingbird frequency domain EM system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 120 degrees NW-SE with the average speed 89 km/h. The average terrain clearance of the bird was 55 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was levelled and filtered. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association. All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000.(Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Rombaken area, Narvik, Nordland

Energy Technology Data Exchange (ETDEWEB)

Rodionov, Alexei; Ofstad, Frode; Koziel, Janusz

2012-07-01

NGU conducted an airborne geophysical survey in Rombaken area in August - September 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 5218 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 90 degrees East West and average speed 98 km/h. The average terrain clearance of the bird was 64 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association.All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000.(Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Rombaken area, Narvik, Nordland

International Nuclear Information System (INIS)

Rodionov, Alexei; Ofstad, Frode; Koziel, Janusz

2012-01-01

NGU conducted an airborne geophysical survey in Rombaken area in August - September 2011 as a part of MINN project. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 5218 line km. The modified Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 200 m line spacing, line direction of 90 degrees East West and average speed 98 km/h. The average terrain clearance of the bird was 64 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was filtered and levelled. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association.All data were gridded with the cell size of 50 m and presented as a shaded relief maps at the scale of 1:50 000.(Author)

A Fractal Interpretation of Controlled-Source Helicopter Electromagnetic Survey Data: Seco Creek, Edwards Aquifer, TX

Science.gov (United States)

Decker, K. T.; Everett, M. E.

2009-12-01

The Edwards aquifer lies in the structurally complex Balcones fault zone and supplies water to the growing city of San Antonio. To ensure that future demands for water are met, the hydrological and geophysical properties of the aquifer must be well-understood. In most settings, fracture lengths and displacements occur in power-law distributions. Fracture distribution plays an important role in determining electrical and hydraulic current flowpaths. 1-D synthetic models of the controlled-source electromagnetic (CSEM) response for layered models with a fractured layer at depth described by the roughness parameter βV, such that 0≤βVlaw length-scale dependence of electrical conductivity are developed. A value of βV = 0 represents homogeneous, continuous media, while a value of 0<βV<1 shows that roughness exists. The Seco Creek frequency-domain helicopter electromagnetic survey data set is analyzed by introducing the similarly defined roughness parameter βH to detect lateral roughness along survey lines. Fourier transforming the apparent resistivity as a function of position along flight line into wavenumber domain using a 256-point sliding window gives the power spectral density (PSD) plot for each line. The value of βH is the slope of the least squares regression for the PSD in each 256-point window. Changes in βH with distance along the flight line are plotted. Large values of βH are found near well-known large fractures and maps of βH produced by interpolating values of βH along survey lines suggest previously undetected structure at depth.

Airborne laser: a tool to study landscape surface features

International Nuclear Information System (INIS)

Ritchie, J.C.; Jackson, T.J.; Everitt, J.H.; Escobar, D.E.; Murphey, J.B.; Grissinger, E.H.

1992-01-01

Landscape surface features related to erosion and hydrology were measured using an airborne laser profiler. The airborne laser profiler made 4,000 measurements per second with a recording accuracy of 5 cm (1.9 inches) on a single measurement. Digital data from the laser are recorded and analyzed with a personal computer. These airborne laser profiles provide information on surface landscape features. Topography and canopy heights, cover, and distribution of natural vegetation were determined in studies in South Texas. Laser measurements of shrub cover along flightlines were highly correlated (R 2 = 0.98) with ground measurements made with line-intercept methods. Stream channel cross sections on Goodwin Creek in Mississippi were measured quickly and accurately with airborne laser data. Airborne laser profile data were used to measure small gullies in a level fallow field and in field with mature soybeans. While conventional ground-based techniques can be used to make these measurements, airborne laser profiler techniques allow data to be collected quickly, at a high density, and in areas that are essentially inaccessible for ground surveys. Airborne laser profiler data can quantify landscape features related to erosion and runoff, and the laser proler has the potential to be a useful tool for providing other data for studying and managing natural resources

A flight test of the strapdown airborne gravimeter SGA-WZ in Greenland

DEFF Research Database (Denmark)

Zhao, Lei; Forsberg, René; Wu, Meiping

2015-01-01

-WZ strapdown airborne gravimeter in Greenland, in an area with good gravity coverage from earlier marine and airborne surveys. An overview of this new system SGA-WZ is given, including system design, sensor performance and data processing. The processing of the SGA-WZ includes a 160 s length finite impulse...

Airborne gamma-ray spectrometer and magnetometer survey: Lund quadrangle, Ely quadrangle, Nevada. Volume I. Final report

International Nuclear Information System (INIS)

1980-01-01

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Ely and Lund 1:250,000 National Topographic Map Series (NTMS quadrangle maps). The survey was part of DOE's National Uranium Resource Evaluation (NURE) Aerial Radiometric Reconnaissance program. Data were collected by a helicopter equipped with a gamma-ray spectrometer having a large crystal volume, and a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test range. Data quality was ensured during the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. The maps were interpreted and an anomaly interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data processing procedures, the data display format, the interpretation rationale, and interpretation methodology. Volume II contains the data displays for a quadrangle and the interpretation results

The Status of Development of Electromagnetic Pumps for Space Application

International Nuclear Information System (INIS)

Kwak, J. S.; Kim, K. H.; Jeong, J. S.; Kim, Hee Reyoung

2013-01-01

Korea lunched this research as a part of the small nuclear power generation technology development for space. In this study, investigated are the basic principle and types of electromagnetic pump and the trend of electromagnetic pump technology development in foreign nations. The survey and analysis give the understanding of the suitability and prospect of electromagnetic pumps as space application technology in Korea. The analysis on the status of the development of electromagnetic pumps was carried out for the application to space environment. It was found that USA was approaching the research and development of electromagnetic pumps for space application. Most electromagnetic pumps surveyed have the efficiency between 35% and 50% where that of AC conduction pump is less than 6%. Further study was thought to have to be given for the mechanical and material characteristics, and the applicability of electromagnetic pumps for space nuclear reactor

Generation of 3-D hydrostratigraphic zones from dense airborne electromagnetic data to assess groundwater model prediction error

Science.gov (United States)

Christensen, N. K.; Minsley, B. J.; Christensen, S.

2017-02-01

We present a new methodology to combine spatially dense high-resolution airborne electromagnetic (AEM) data and sparse borehole information to construct multiple plausible geological structures using a stochastic approach. The method developed allows for quantification of the performance of groundwater models built from different geological realizations of structure. Multiple structural realizations are generated using geostatistical Monte Carlo simulations that treat sparse borehole lithological observations as hard data and dense geophysically derived structural probabilities as soft data. Each structural model is used to define 3-D hydrostratigraphical zones of a groundwater model, and the hydraulic parameter values of the zones are estimated by using nonlinear regression to fit hydrological data (hydraulic head and river discharge measurements). Use of the methodology is demonstrated for a synthetic domain having structures of categorical deposits consisting of sand, silt, or clay. It is shown that using dense AEM data with the methodology can significantly improve the estimated accuracy of the sediment distribution as compared to when borehole data are used alone. It is also shown that this use of AEM data can improve the predictive capability of a calibrated groundwater model that uses the geological structures as zones. However, such structural models will always contain errors because even with dense AEM data it is not possible to perfectly resolve the structures of a groundwater system. It is shown that when using such erroneous structures in a groundwater model, they can lead to biased parameter estimates and biased model predictions, therefore impairing the model's predictive capability.

Generation of 3-D hydrostratigraphic zones from dense airborne electromagnetic data to assess groundwater model prediction error

Science.gov (United States)

Christensen, Nikolaj K; Minsley, Burke J.; Christensen, Steen

2017-01-01

We present a new methodology to combine spatially dense high-resolution airborne electromagnetic (AEM) data and sparse borehole information to construct multiple plausible geological structures using a stochastic approach. The method developed allows for quantification of the performance of groundwater models built from different geological realizations of structure. Multiple structural realizations are generated using geostatistical Monte Carlo simulations that treat sparse borehole lithological observations as hard data and dense geophysically derived structural probabilities as soft data. Each structural model is used to define 3-D hydrostratigraphical zones of a groundwater model, and the hydraulic parameter values of the zones are estimated by using nonlinear regression to fit hydrological data (hydraulic head and river discharge measurements). Use of the methodology is demonstrated for a synthetic domain having structures of categorical deposits consisting of sand, silt, or clay. It is shown that using dense AEM data with the methodology can significantly improve the estimated accuracy of the sediment distribution as compared to when borehole data are used alone. It is also shown that this use of AEM data can improve the predictive capability of a calibrated groundwater model that uses the geological structures as zones. However, such structural models will always contain errors because even with dense AEM data it is not possible to perfectly resolve the structures of a groundwater system. It is shown that when using such erroneous structures in a groundwater model, they can lead to biased parameter estimates and biased model predictions, therefore impairing the model's predictive capability.

Airborne gravity field Measurements - status and developments

DEFF Research Database (Denmark)

Olesen, Arne Vestergaard; Forsberg, René

2016-01-01

English Abstract:DTU-Space has since 1996 carried out large area airborne surveys over both polar, tropical and temperate regions, especially for geoid determination and global geopotential models. Recently we have started flying two gravimeters (LCR and Chekan-AM or inertial navigation systems) ...

Significance of radioelement concentration measurements made by airborne gamma-ray spectrometry over the Canadian Shield

International Nuclear Information System (INIS)

Charbonneau, B.W.; Killeen, P.G.; Carson, J.M.; Cameron, G.W.; Richardson, K.A.

1976-01-01

Results of airborne gamma-ray spectrometer surveys conducted by the Geological Survey of Canada are presented as maps contoured in units of radioelement and concentration ratios. These contoured values represent the average surface concentrations of the radioelements over areas of the order of several square kilometres. The relationship between this ''average surface concentration'' and the radioelement concentration in bedrock underlying the area depends on: (1) the percentage of outcrop; (2) the relation between overburden and bedrock radioelement concentration; (3) percentage of marshland or surface water in the area; (4) soil moisture; and (5) density of vegetation. More than 2500 portable gamma-ray spectrometer analyses of outcrop and overburden have been made in the Bancroft, Elliot Lake and Fort Smith areas of the Canadian Precambrian Shield. In the areas examined, the radioelement concentrations in glacial drift reflect the concentrations in the underlying bedrock. Rocks with near-crustal average contents of thorium, uranium and potassium are overlain by glacial drift having approximately the same concentrations. As the concentration in bedrock increases, the concentration in the local overburden also increases, but not to the same extent. In addition, in-situ gamma-ray spectrometry measurements were made at almost 1000 stations within the area of airborne surveys near Mont Laurier and Elliot Lake. These ground measurements were compared with the airborne measurements by averaging the values for all those ground stations located in the areas between each contour level on airborne maps. Radioelement concentrations in bedrock are considerably higher than corresponding airborne measurements, and this difference between bedrock and airborne values increases at higher radioelement concentrations. Radioelement concentrations in glacial drift are only slightly higher than airborne contour values for the same area. Airborne contour maps of the radioelement ratios

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in Kviteseid area, Lenvik, Troms

International Nuclear Information System (INIS)

Baranwal, Vikas C.; Rodionov, Alexei; Ofstad, Frode

2012-01-01

In cooperation with the geologist for Buskerud, Telemark and Vestfold, the NGU conducted an airborne geophysical survey in Kviteseid area in May 2012. This report describes and documents the acquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 3514 line km. The optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data acquisition. The survey was flown with 100 m line spacing, line direction of 130 degrees - 210 degrees and average speed of 98 km/h. A smaller area was also flown at 100 m line spacing 50 m away from larger flight lines so that smaller area could be covered with 50 m line spacing. The average terrain clearance of the helicopter was 65 m. Collected data were processed in NGU using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and also for International Geomagnetic Reference Field (IGRF). Finally, some along-line noises were removed using standard micro-leveling algorithm. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association (IAEA). Final processed data were gridded with the cell size of 25 m and 12 m for 100 m and 50 m line spacing, respectively. They are presented as a shaded relief maps at the scale of 1:20 000 and 1:10 000, respectively.(Author)

An airborne gamma ray snow survey of a forest covered area with a deep snowpack

International Nuclear Information System (INIS)

Glynn, J.E.; Carroll, T.R.; Holman, P.B.; Grasty, R.L.

1988-01-01

Problems arising from the airborne gamma ray measurement of snow water equivalent over a forest covered deep snowpack are examined. The principal sources of error are believed to be due to the radioactivity in the biomass and to variability in the snow cover. A theoretical model is developed to correct the airborne measurements for these sources of error. The application of the theory to data collected over the St. John River Basin, located in the eastern part of Canada and the United States, is found to significantly improve the airborne results

An empirical approach to inversion of an unconventional helicopter electromagnetic dataset

Science.gov (United States)

Pellerin, L.; Labson, V.F.

2003-01-01

A helicopter electromagnetic (HEM) survey acquired at the U.S. Idaho National Engineering and Environmental Laboratory (INEEL) used a modification of a traditional mining airborne method flown at low levels for detailed characterization of shallow waste sites. The low sensor height, used to increase resolution, invalidates standard assumptions used in processing HEM data. Although the survey design strategy was sound, traditional interpretation techniques, routinely used in industry, proved ineffective. Processed data and apparent resistivity maps were severely distorted, and hence unusable, due to low flight height effects, high magnetic permeability of the basalt host, and the conductive, three-dimensional nature of the waste site targets.To accommodate these interpretation challenges, we modified a one-dimensional inversion routine to include a linear term in the objective function that allows for the magnetic and three-dimensional electromagnetic responses in the in-phase data. Although somewhat ad hoc, the use of this term in the inverse routine, referred to as the shift factor, was successful in defining the waste sites and reducing noise due to the low flight height and magnetic characteristics of the host rock. Many inversion scenarios were applied to the data and careful analysis was necessary to determine the parameters appropriate for interpretation, hence the approach was empirical. Data from three areas were processed with this scheme to highlight different interpretational aspects of the method. Wastes sites were delineated with the shift terms in two of the areas, allowing for separation of the anthropomorphic targets from the natural one-dimensional host. In the third area, the estimated resistivity and the shift factor were used for geological mapping. The high magnetic content of the native soil enabled the mapping of disturbed soil with the shift term. Published by Elsevier Science B.V.

Airborne gamma-ray survey around the Negoro fault. 1; Negoro danso shuhen chiiki ni okeru kuchu {gamma} sen tansa. 1

Energy Technology Data Exchange (ETDEWEB)

Nakayama, E.; Kasuya, Y.; Hasegawa, H. [Aero Asahi Corp., Tokyo (Japan); Tsukuda, E. [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

An airborne gamma-ray survey was carried out to investigate the active fault system in the central structure line in the peripheral area of the city of Wakayama. At the same time, with an objective to enhance applicability of the airborne gamma-ray survey to active fault investigation, fundamental data were acquired and discussed. The measurement data were processed according to the standard method specified by IAEA. An ID-FFT filter and a nonlinear filter were employed to extract anomalous gamma-ray intensity values. The gamma-ray intensity distribution chart shows a noticeable positive anomalous area extending from the central part of the western edge to the north-east direction. This area agrees nearly well with the Negoro fault, but its peak portion is positioned slightly more to south than the position of the Negoro fault shown in existing data. The Sakuraike fault and the vicinity of the central structure line also show positive anomaly as a whole, particularly remarkably in the vicinity of their converging portion. However, differing from the vicinity of the Negoro fault, the areas are not extracted as an anomalous area which has directionality and extends in a line form. One of the factors for this would be that it is a fault in unsolidified deposits with low opening trend, differing from the one in solidified rocks. 1 fig., 3 tabs.

Airborne Gravity: NGS' Gravity Data for ES03 (2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Maryland, Pennsylvania, New Jersey, West Virginia, Virginia, Delaware, and the Atlantic Ocean collected in 2013 over 1 survey. This data...

Upper High School Students' Understanding of Electromagnetism

Science.gov (United States)

Saglam, Murat; Millar, Robin

2006-01-01

Although electromagnetism is an important component of upper secondary school physics syllabuses in many countries, there has been relatively little research on students' understanding of the topic. A written test consisting of 16 diagnostic questions was developed and used to survey the understanding of electromagnetism of upper secondary school…

Occupational exposure to beryllium in French enterprises: a survey of airborne exposure and surface levels.

Science.gov (United States)

Vincent, Raymond; Catani, Jacques; Créau, Yvon; Frocaut, Anne-Marie; Good, Andrée; Goutet, Pierre; Hou, Alain; Leray, Fabrice; André-Lesage, Marie-Ange; Soyez, Alain

2009-06-01

An assessment survey of occupational exposure to beryllium (Be) was conducted in France between late 2004 and the end of 2006. Exposure estimates were based on the analytical results of samples collected from workplace air and from work surfaces in 95 facilities belonging to 37 sectors of activity. The results of this study indicated airborne Be concentrations in excess of the occupational exposure limit value of 2 microg m(-3) recommended in France. Metallurgy and electronic component manufacturing represented the activities and occupations where workers had the highest arithmetic mean exposures to Be. Surface contamination levels were also high and frequently exceeded thresholds recommended by different bodies. These results should prompt the development of prevention programmes that include Be substitution, process control and surface decontamination, in conjunction with suitable medical surveillance.

Polar gravity fields from GOCE and airborne gravity

DEFF Research Database (Denmark)

Forsberg, René; Olesen, Arne Vestergaard; Yidiz, Hasan

2011-01-01

Airborne gravity, together with high-quality surface data and ocean satellite altimetric gravity, may supplement GOCE to make consistent, accurate high resolution global gravity field models. In the polar regions, the special challenge of the GOCE polar gap make the error characteristics...... of combination models especially sensitive to the correct merging of satellite and surface data. We outline comparisons of GOCE to recent airborne gravity surveys in both the Arctic and the Antarctic. The comparison is done to new 8-month GOCE solutions, as well as to a collocation prediction from GOCE gradients...... in Antarctica. It is shown how the enhanced gravity field solutions improve the determination of ocean dynamic topography in both the Arctic and in across the Drake Passage. For the interior of Antarctica, major airborne gravity programs are currently being carried out, and there is an urgent need...

Geophysical Survey in Sub-Saharan Africa: magnetic and Electromagnetic Investigation of the UNESCO World Heritage Site of Songo Mnara, Tanzania

OpenAIRE

Welham, Kate; Fleisher, J.; Cheetham, Paul; Manley, Harry; Steele, C.; Wynne-Jones, S.

2014-01-01

Magnetometry and Slingram electromagnetic surveys were\\ud conducted at the UNESCO World Heritage Site of Songo Mnara, Tanzania, as part of a multi-national programme of investigation to examine the uses of space within and outside of this stonetown. The town was a major Islamic trading port during the 14th and 15th centuries.The surveys detected significant evidence for the containment of activities within the town walls, and previously unknown anthropogenic activity was revealed between the ...

Airborne Gravity: NGS' Gravity Data for EN09 (2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Massachusetts, Connecticut, Rhode Island, New Hampshire, New York, and the Atlantic Ocean collected in 2012 over 1 survey. This data set is...

Geological interpretation of an airborne gamma-ray spectrometer survey of the Hearne Lake area, Northwest Territories

International Nuclear Information System (INIS)

Newton, A.R.; Slaney, V.R.

1978-01-01

This study shows how large volumes of airborne data can be displayed in a simple format which provides both mapping and exploration geologists with information not easily obtained from the original data. Eleven lines or part-lines from a gamma-ray survey of the Hearne Lake area were chosen as test lines, and airphotos were used to identify outcrops of each rock type and the distribution of overburden, swamp and water along each line. Geological maps were used to locate the test lines and to provide a listing of the rock types in the area. With this information, it was possible to calculate the average radioelement characteristics of each rock type and to group the rock signatures into a number of rock classes. The techniques described are most usefully applied to those areas where the outcrop is extensive, where some form of geological map already exists, where there are airphotos at scales of 1:30,000 or larger, and where the gamma-ray survey lines are less than 2.5 km apart

Airborne Gravity: NGS' Gravity Data for EN08 (2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for New York, Vermont, New Hampshire, Massachusettes, Maine, and Canada collected in 2013 over 1 survey. This data set is part of the Gravity...

Airborne Gravity: NGS' Gravity Data for EN10 (2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for New York, Pennsylvania, New Jersey, Connecticut and the Atlantic Ocean collected in 2013 over 1 survey. This data set is part of the...

Optimization and inverse problems in electromagnetism

CERN Document Server

Wiak, Sławomir

2003-01-01

From 12 to 14 September 2002, the Academy of Humanities and Economics (AHE) hosted the workshop "Optimization and Inverse Problems in Electromagnetism". After this bi-annual event, a large number of papers were assembled and combined in this book. During the workshop recent developments and applications in optimization and inverse methodologies for electromagnetic fields were discussed. The contributions selected for the present volume cover a wide spectrum of inverse and optimal electromagnetic methodologies, ranging from theoretical to practical applications. A number of new optimal and inverse methodologies were proposed. There are contributions related to dedicated software. Optimization and Inverse Problems in Electromagnetism consists of three thematic chapters, covering: -General papers (survey of specific aspects of optimization and inverse problems in electromagnetism), -Methodologies, -Industrial Applications. The book can be useful to students of electrical and electronics engineering, computer sci...

Airborne Gravity: NGS' Gravity Data for AN08 (2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2016 over one survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum...

Airborne gamma-ray spectrometry

DEFF Research Database (Denmark)

Hovgaard, Jens

A new method - Noise Adjusted Singular Value Decomposition, NASVD - for processing gamma-ray spectra has been developed as part of a Ph.D. project. By using this technique one is able to decompose a large set of data - for example from airborne gamma-ray surveys - into a few spectral components....... By knowing the spectral components and their amplitudes in each of the measured spectra one is able to extract more information from the data than possible with the methods used otherwise....

The theoretical study of full spectrum analysis method for airborne gamma-ray spectrometric data

International Nuclear Information System (INIS)

Ni Weichong

2011-01-01

Spectra of airborne gamma-ray spectrometry was found to be the synthesis of spectral components of radioelement sources by analyzing the constitution of radioactive sources for airborne gamma-ray spectrometric survey and establishing the models of gamma-ray measurement. The mathematical equation for analysising airborne gamma-ray full spectrometric data can be expressed into matrix and related expansions were developed for the mineral resources exploration, environmental radiation measurement, nuclear emergency monitoring, and so on. Theoretical study showed that the atmospheric radon could be directly computed by airborne gamma-ray spectrometric data with full spectrum analysis without the use of the accessional upward-looking detectors. (authors)

Multi-frequency Electromagnetic Induction Survey for Archaeological Prospection: Approach and Results in Han Hangu Pass and Xishan Yang in China

Science.gov (United States)

Tang, Panpan; Chen, Fulong; Jiang, Aihui; Zhou, Wei; Wang, Hongchao; Leucci, Giovanni; de Giorgi, Lara; Sileo, Maria; Luo, Rupeng; Lasaponara, Rosa; Masini, Nicola

2018-04-01

This study presents the potential of multi-frequency electromagnetic induction (EMI) in archaeology. EMI is currently less employed for archaeological prospection with respect to other geophysical techniques. It is capable of identifying shallow subsurface relics by simultaneously measuring the apparent electrical conductivity (ECa) and apparent magnetic susceptibility (MSa). Moreover, frequency sounding is able to quantify the depths and vertical shapes of buried structures. In this study, EMI surveys with five frequencies were performed at two heritage sites with different geological conditions: Han Hangu Pass characterized by cinnamon soil and Xishan Yang by sandy loams. In the first site, high ECa values were observed with variations in depth correlated to archaeological remains. Moreover, electromagnetic anomalies related to an ancient road and five kiln caves were identified. In the second site, an ancient tomb, indicating extremely low ECa and high MSa, was discovered. Its electromagnetic properties are attributed to the cavity and ferroferric oxides.

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in the Storforshei area, Rana, Nordland

International Nuclear Information System (INIS)

Rodionov, Alexei; Ofstad, Frode; Tassis, Georgios

2012-01-01

NGU conducted an airborne geophysical survey in Mo i Rana area in July 2012. This report describes and documents the aquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 1414 line km. The Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data aquisition. The survey was flown with 100 m line spacing, line direction of 180 deg North-South (in the west) and 150 deg NorthWest-SouthEast (in the east) with the average speed 96 km/h. The average terrain clearance of the bird was 55 m. Collected data were processed by AR GeoConsulting using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was levelled and filtered. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association (IAEA). All data were gridded with the cell size of 25 m and presented as shaded relief maps at the scale of 1:25 000.(Author)

Helicopter-borne magnetic, electromagnetic and radiometric geophysical survey in the Storforshei area, Rana, Nordland

Energy Technology Data Exchange (ETDEWEB)

Rodionov, Alexei; Ofstad, Frode; Tassis, Georgios

2012-07-01

NGU conducted an airborne geophysical survey in Mo i Rana area in July 2012. This report describes and documents the aquisition, processing and visualization of recorded datasets. The geophysical survey results reported herein are 1414 line km. The Geotech Ltd. Hummingbird frequency domain system supplemented by optically pumped cesium magnetometer and 1024 channels RSX-5 spectrometer was used for data aquisition. The survey was flown with 100 m line spacing, line direction of 180 deg North-South (in the west) and 150 deg NorthWest-SouthEast (in the east) with the average speed 96 km/h. The average terrain clearance of the bird was 55 m. Collected data were processed by AR GeoConsulting using Geosoft Oasis Montaj software. Raw total magnetic field data were corrected for diurnal variation and levelled using standard micro levelling algorithm. EM data were filtered and levelled using both automated and manual levelling procedure. Apparent resistivity was calculated from in-phase and quadrature data for each of the five frequencies separately using a homogeneous half space model. Apparent resistivity dataset was levelled and filtered. Radiometric data were processed using standard procedures recommended by International Atomic Energy Association (IAEA). All data were gridded with the cell size of 25 m and presented as shaded relief maps at the scale of 1:25 000.(Author)

Airborne Gravity: NGS' Gravity Data for AS01 (2008)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2008 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for CS04 (2009)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Texas collected in 2009 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for AN05 (2011)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2011 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for TS01 (2014)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Puerto Rico and the Virgin Islands collected in 2009 over 1 survey. This data set is part of the Gravity for the Re-definition of the...

Airborne Gravity: NGS' Gravity Data for AN06 (2011)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2011 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for AS02 (2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2010 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for EN01 (2011)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for New York, Canada, and Lake Ontario collected in 2011 over 1 survey. This data set is part of the Gravity for the Re-definition of the...

Airborne Gravity: NGS' Gravity Data for AN03 (2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2010 and 2012 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum...

Airborne Gravity: NGS' Gravity Data for AN04 (2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2010 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for CS05 (2014)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Texas collected in 2014 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for EN06 (2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Maine, Canada, and the Atlantic Ocean collected in 2012 over 2 surveys. This data set is part of the Gravity for the Re-definition of the...

Airborne Gravity: NGS' Gravity Data for AN02 (2010)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2010 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for ES01 (2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Florida, the Bahamas, and the Atlantic Ocean collected in 2013 over 1 survey. This data set is part of the Gravity for the Re-definition of...

The DESMEX Project - Deep Electromagnetic Sounding for Mineral EXploration

Science.gov (United States)

Meyer, U.; Becken, M.; Stolz, R.; Nittinger, C.; Cherevatova, M.; Siemon, B.; Martin, T.; Petersen, H.; Steuer, A.

2017-12-01

The DESMEX project (Deep Electromagnetic Sounding for Mineral Exploration) aims to develop independent semi-airborne frequency domain systems for mineral exploration down to depths of 1 km and deeper. Two different helicopter-towed systems are being designed and tested using source installations on ground. One system uses among other equipment conventional three axis induction coils, a 3D-fluxgate and a high precision inertial motion unit. The use of the two different magnetometers allows to record data in a broad frequency range from 1 Hz to 10 kHz. The second system uses a newly developed SQUID-based sensing system of a similar frequency range and a self made inertial motion unit. Horizontal electric dipole transmitters provided by the Leibniz Institute for Applied Geophysics in Hannover and the Institute of Geophysics and Meteorology of the University in Cologne are used as ground based sources. First system tests showed a good performance of both systems with general noise levels below 50 pT/root(Hz). Test flights above the common survey area proved that the desired depth of investigation can be achieved and that the data is consistent with the subsurface conductivity structures. In order to verify the data acquired from the newly developed system at shallow depths and to provide a better starting model for later inversion calculations helicopter borne frequency domain electromagnetics has been acquired and fully processed over the test site Schleiz - Greiz in Germany. To further relate the subsurface conductivity models to the subsurface geology and mineralogy, petrophysical investigations have been performed on rock samples from the site of investigation and analogue samples.

Airborne Gravity: NGS' Gravity Data for CS08 (2015)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for CS08 collected in 2006 over 1 survey. This data set is part of the Gravity for the Re-definition of the American Vertical Datum (GRAV-D)...

Airborne Gravity: NGS' Gravity Data for MS02 (2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data over southern Arizona and New Mexico overlapping into Mexico collected in 2016 over 2 surveys, AZ16-1 and AZ16-2. This data set is part of the...

Airborne Gravity: NGS' Gravity Data for ES02 (2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Florida and the Gulf of Mexico collected in 2013 over 1 survey. This data set is part of the Gravity for the Re-definition of the American...

Integrated interpretation of overlapping AEM datasets achieved through standardisation

Science.gov (United States)

Sørensen, Camilla C.; Munday, Tim; Heinson, Graham

2015-12-01

Numerous airborne electromagnetic surveys have been acquired in Australia using a variety of systems. It is not uncommon to find two or more surveys covering the same ground, but acquired using different systems and at different times. Being able to combine overlapping datasets and get a spatially coherent resistivity-depth image of the ground can assist geological interpretation, particularly when more subtle geophysical responses are important. Combining resistivity-depth models obtained from the inversion of airborne electromagnetic (AEM) data can be challenging, given differences in system configuration, geometry, flying height and preservation or monitoring of system acquisition parameters such as waveform. In this study, we define and apply an approach to overlapping AEM surveys, acquired by fixed wing and helicopter time domain electromagnetic (EM) systems flown in the vicinity of the Goulds Dam uranium deposit in the Frome Embayment, South Australia, with the aim of mapping the basement geometry and the extent of the Billeroo palaeovalley. Ground EM soundings were used to standardise the AEM data, although results indicated that only data from the REPTEM system needed to be corrected to bring the two surveys into agreement and to achieve coherent spatial resistivity-depth intervals.

Assessment of NASA airborne laser altimetry data using ground-based GPS data near Summit Station, Greenland

Science.gov (United States)

Brunt, Kelly M.; Hawley, Robert L.; Lutz, Eric R.; Studinger, Michael; Sonntag, John G.; Hofton, Michelle A.; Andrews, Lauren C.; Neumann, Thomas A.

2017-03-01

A series of NASA airborne lidars have been used in support of satellite laser altimetry missions. These airborne laser altimeters have been deployed for satellite instrument development, for spaceborne data validation, and to bridge the data gap between satellite missions. We used data from ground-based Global Positioning System (GPS) surveys of an 11 km long track near Summit Station, Greenland, to assess the surface-elevation bias and measurement precision of three airborne laser altimeters including the Airborne Topographic Mapper (ATM), the Land, Vegetation, and Ice Sensor (LVIS), and the Multiple Altimeter Beam Experimental Lidar (MABEL). Ground-based GPS data from the monthly ground-based traverses, which commenced in 2006, allowed for the assessment of nine airborne lidar surveys associated with ATM and LVIS between 2007 and 2016. Surface-elevation biases for these altimeters - over the flat, ice-sheet interior - are less than 0.12 m, while assessments of measurement precision are 0.09 m or better. Ground-based GPS positions determined both with and without differential post-processing techniques provided internally consistent solutions. Results from the analyses of ground-based and airborne data provide validation strategy guidance for the Ice, Cloud, and land Elevation Satellite 2 (ICESat-2) elevation and elevation-change data products.

Groundwater and Thaw Legacy of a Large Paleolake in Taylor Valley, East Antarctica as Evidenced by Airborne Electromagnetic and Sedimentological Techniques

Science.gov (United States)

Doran, P. T.; Myers, K. F.; Foley, N.; Tulaczyk, S. M.; Dugan, H. A.; Auken, E.; Mikucki, J.; Virginia, R. A.

2017-12-01

The McMurdo Dry Valleys (MDVs) in east Antarctica contain a number of perennial ice-covered lakes fed by ephemeral meltwater streams. Lake Fryxell in Taylor Valley, is roughly 5.5 km long and approximately 22 m deep. Paleodeltas and paleoshorelines throughout Fryxell Basin provide evidence of significant lake level change occurring since the Last Glacial Maximum (LGM). During the LGM, grounded ice in the Ross Sea extended into the eastern portion of Taylor Valley, creating a large ice dammed paleolake. Glacial Lake Washburn (GLW) was roughly 300 m higher than modern day Lake Fryxell and its formation and existence has been debated. In this study, we use Geographical Information System and remote sensing techniques paired with regional resistivity data to provide new insight into the paleohydrology of the region. The existence of GLW is supported by new findings of a deep groundwater system beneath Lake Fryxell, which is interpreted as the degrading thaw bulb of GLW. Airborne resistivity data collected by SkyTEM, a time-domain airborne electromagnetic sensor system was used to map groundwater systems in the lake basin. Subsurface characteristics can be inferred from the relationship of resistivity to temperature, salinity, porosity, and degree of saturation. A large low resistivity region indicative of liquid water extends hundreds of meters away from the modern lake extent which is consistent with the presence of a degrading thaw bulb from GLW. As lake level in Fryxell Basin fell to modern levels, the saturated sediment beneath the lake began to freeze as it became exposed to low atmospheric temperatures. We hypothesize that this process is ongoing and will continue until equilibrium is reached between the geothermal gradient and atmospheric temperatures. Though liquid groundwater systems were previously thought to be minimal or nonexistent in the MDVs, regional resistivity data now show that extensive groundwater reservoirs exist beneath these lakes. In addition

Airborne Laser Polarization Sensor

Science.gov (United States)

Kalshoven, James, Jr.; Dabney, Philip

1991-01-01

Instrument measures polarization characteristics of Earth at three wavelengths. Airborne Laser Polarization Sensor (ALPS) measures optical polarization characteristics of land surface. Designed to be flown at altitudes of approximately 300 m to minimize any polarizing or depolarizing effects of intervening atmosphere and to look along nadir to minimize any effects depending on look angle. Data from measurements used in conjunction with data from ground surveys and aircraft-mounted video recorders to refine mathematical models used in interpretation of higher-altitude polarimetric measurements of reflected sunlight.

Merging of airborne gravity and gravity derived from satellite altimetry: Test cases along the coast of greenland

DEFF Research Database (Denmark)

Olesen, Arne Vestergaard; Andersen, Ole Baltazar; Tscherning, C.C.

2002-01-01

for the use of gravity data especially, when computing geoid models in coastal regions. The presence of reliable marine gravity data for independent control offers an opportunity to study procedures for the merging of airborne and satellite data around Greenland. Two different merging techniques, both based......The National Survey and Cadastre - Denmark (KMS) has for several years produced gravity anomaly maps over the oceans derived from satellite altimetry. During the last four years, KMS has also conducted airborne gravity surveys along the coast of Greenland dedicated to complement the existing...... onshore gravity coverage and fill in new data in the very-near coastal area, where altimetry data may contain gross errors. The airborne surveys extend from the coastline to approximately 100 km offshore, along 6000 km of coastline. An adequate merging of these different data sources is important...

Using an Optionally Piloted Aircraft for Airborne Gravity Observations with the NOAA GRAV-D Project

Science.gov (United States)

Youngman, M.; Johnson, J. A.; van Westrum, D.; Damiani, T.

2017-12-01

The U.S. National Geodetic Survey's (NGS) Gravity for the Redefintion of the American Vertical Datum (GRAV-D) project is collecting airborne gravity data to support a 1 cm geoid. Started in 2008, this project will collect airborne gravity data over the entire U.S. and territories by 2022. As of June 30, 2017, the project was almost 62% complete. With recent technological developments, NGS has been exploring using unmanned aircraft for airborne gravity measurements. This presentation will focus on results from two surveys over the U.S. Appalachian and Rocky Mountains using the Aurora Centaur Optionally Piloted Aircraft and the Micro-g Lacoste Turnkey Airborne Gravimeter System 7 (TAGS7). Collecting high quality data as well as dealing with remote locations has been a challenge for the GRAV-D project and the field of airborne gravity in general. Unmanned aircraft could potentially improve data quality, handle hard to reach locations, and reduce pilot fatigue. The optionally piloted Centaur aircraft is an attractive option because it is not restricted in U.S. airspace and delivers high quality gravity data. Specifically, the Centaur meets U.S. Federal Aviation Administration regulations for Unmanned Aircraft Systems (UAS) by using a safety pilot on board to maintain line of sight and the ability to take control in the event of an emergency. Even though this is a sizeable UAS, most traditional gravimeters are too large and heavy for the platform. With a smaller and lighter design, the TAGS7 was used for its ability to conform to the aircraft's size restrictions, with the added benefit of upgraded performance capabilities. Two surveys were performed with this aircraft and gravimeter, one in April and one in August to September of 2017. Initial results indicate that the high-gain, fast response of the Centaur autopilot (optimized for flights without passengers), coupled with the full-force feedback sensor of the TAGS7, provides superior performance in all conditions, and

Chemicals, metals, and pesticide pits waste unit low induction number electromagnetic survey

Energy Technology Data Exchange (ETDEWEB)

Cumbest, R.J.; Mohon, D.

1995-06-01

An electromagnetic survey was conducted at the Chemicals, Metals, and Pesticide Waste Unit to identify any buried metallic objects that may be present in the materials used to fill and cover the pits after removal of pit debris. The survey was conducted with a Geonics EM-31 Terrain Conductivity Meter along north - south oriented traverses with 5-ft station intervals to produce a 5-ft by 5-ft square grid node pattern. Both conductivity and in-phase components were measured at each station for vertical dipole orientation with the common axis of the dipoles in the north - south and east - west orientations. The conductivity data clearly show elevated conductivities (2.1 to 7.0 mS/m) associated with the material over the pits, as compared with the surrounding area that is characterized by lower conductivities (1 to 2 mS/m). This is probably the result of the higher clay content of the fill material relative to the surrounding area, which has a higher sand to clay ratio and the presence of a plastic cover beneath the fill that has probably trapped water. Many metal objects are present in the survey area including manhole covers, monitoring well heads, metal, signs, drain culverts, abandoned wells, and BP waste unit marker balls. AU of these exhibit associated conductivity and in-phase anomalies of various magnitude. In addition to these anomalies that can be definitely associated with surface sources, conductivity and in-phase anomalies are also present with no obvious surface source. These anomalies are probably indicative of subsurface buried metallic objects. A high concentration of these objects appears to be present in the southwest corner of the survey area.

Surveying Future Surveys

Science.gov (United States)

Carlstrom, John E.

2016-06-01

The now standard model of cosmology has been tested and refined by the analysis of increasingly sensitive, large astronomical surveys, especially with statistically significant millimeter-wave surveys of the cosmic microwave background and optical surveys of the distribution of galaxies. This talk will offer a glimpse of the future, which promises an acceleration of this trend with cosmological information coming from new surveys across the electromagnetic spectrum as well as particles and even gravitational waves.

Modeling induced polarization effects in helicopter time domain electromagnetic data: Synthetic case studies

DEFF Research Database (Denmark)

Viezzoli, Andrea; Kaminskiy, Vladislav; Fiandaca, Gianluca

2017-01-01

constrained multiparametric inversion was evaluated, including recovery of chargeability distributions from shallow and deep targets based on analysis of induced polarization (IP) effects, simulated in airborne TDEM data. Different scenarios were studied, including chargeable targets associated...... processing and the effect of constraints, and a priori information. We have used a 1D layered earth model approximation and lateral constraints. Synthetic simulations were performed for several models and the corresponding Cole-Cole parameters. The possibility to recover these models by means of laterally...... the airborne electromagnetic is most sensitive (e.g., approximately 1 ms), it is possible to recover deep chargeable targets (to depths more than 130 m) in association with high electrical conductivity and in resistive environments. Furthermore, it was found that the recovery of a deep conductor, masked...

Airborne Gravity: NGS' Gravity Data for ES04 (2013-2014)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for North Carolina, South Carolina, Virginia, and the Atlantic Ocean collected in 2013 and 2014 over two surveys. This data set is part of the...

Airborne Gravity: NGS' Gravity Data for CN02 (2013 & 2014)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Nebraska collected in 2013 & 2014 over 3 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical...

Airborne Gravity: NGS' Gravity Data for EN02 (2011-2012)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for New York, Pennsylvania, Ohio, Michigan, Canada and Lake Erie collected in 2011 and 2012 over 3 surveys. This data set is part of the...

On background radiation gradients – the use of airborne surveys when searching for orphan sources using mobile gamma-ray spectrometry

International Nuclear Information System (INIS)

Kock, Peder; Rääf, Christopher; Samuelsson, Christer

2014-01-01

Systematic background radiation variations can lead to both false positives and failures to detect an orphan source when searching using car-borne mobile gamma-ray spectrometry. The stochastic variation at each point is well described by Poisson statistics, but when moving in a background radiation gradient the mean count rate will continually change, leading to inaccurate background estimations. Airborne gamma spectrometry (AGS) surveys conducted on the national level, usually in connection to mineral exploration, exist in many countries. These data hold information about the background radiation gradients which could be used at the ground level. This article describes a method that aims to incorporate the systematic as well as stochastic variations of the background radiation. We introduce a weighted moving average where the weights are calculated from existing AGS data, supplied by the Geological Survey of Sweden. To test the method we chose an area with strong background gradients, especially in the thorium component. Within the area we identified two roads which pass through the high-variability locations. The proposed method is compared with an unweighted moving average. The results show that the weighting reduces the excess false positives in the positive background gradients without introducing an excess of failures to detect a source during passage in negative gradients. -- Highlights: • We present a simple method to account for gradients in the natural background radiation. • Gradients in the natural radiation background can be modelled at the ground level using AGS data. • The number of false positives due to background gradients can be reduced by using airborne data

Using ground-based geophysics to constrain the interpretation of airborne TEM data recorded across the Okavango Delta, Botswana

Science.gov (United States)

Podgorski, J. E.; Kalscheuer, T.; Doetsch, J.; Rabenstein, L.; Tshoso, G.; Meier, P.; Horstmeyer, H.; Kgotlhang, L.; Ploug, C.; Auken, E.; Kinzelbach, W. K.; Green, A. G.

2011-12-01

The Okavango Delta in northern Botswana is a near endorheic inland delta that has developed over the past ~2 MA in an active graben at the southwestern end of the East Africa Rift System. An annual flood from the north causes a slowly flowing surface water regime in the delta, but previous wetter climatic periods were responsible for intermittent lacustrine environments. The Okavango Delta is the largest permanent water body in the Kalahari Desert and, as such, represents an important resource for wildlife and humans alike. An airborne time-domain electromagnetic (TEM) survey, commissioned by the Botswana government, was undertaken in 2007 for the purpose of better understanding the hydrogeology of the delta. Initial processing and inversion of these data show within the main fan of the delta a resistive 20-50 m thick surface layer underlain by a 30-200 m thick conductive layer. In the upper fan, the conductive layer is underlain by a resistive unit beginning at about 150 m depth. This unit exhibits a dendritic pattern implying a fluvial origin. To help interpret this and other structures, geophysical field work was initiated in early 2011 at various locations in the delta. Seismic reflection and refraction, electrical resistive tomography (ERT), and ground TEM methods were employed. The seismic methods are useful for delineating the boundaries of the weathering and basement layers, whereas ERT provides an independent estimate of the resistivity structure, particularly at shallow depths. Ground TEM allows for a direct comparison with the airborne TEM soundings, helping to estimate the accuracy of the latter. Though still evolving, the current large-scale hydrogeological interpretation of the airborne data set includes a fresh water-saturated surface layer underlain by a saline aquifer and clay aquitard. In the upper fan of the delta, a fresh water aquifer appears to lie between the aquitard and the basement rock.

Airborne Gravity: NGS' Gravity Data for CS02 (2008-2009)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Louisana and Mississippi collected in 2008-2009 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American...

Airborne wireless communication systems, airborne communication methods, and communication methods

Science.gov (United States)

Deaton, Juan D [Menan, ID; Schmitt, Michael J [Idaho Falls, ID; Jones, Warren F [Idaho Falls, ID

2011-12-13

An airborne wireless communication system includes circuitry configured to access information describing a configuration of a terrestrial wireless communication base station that has become disabled. The terrestrial base station is configured to implement wireless communication between wireless devices located within a geographical area and a network when the terrestrial base station is not disabled. The circuitry is further configured, based on the information, to configure the airborne station to have the configuration of the terrestrial base station. An airborne communication method includes answering a 911 call from a terrestrial cellular wireless phone using an airborne wireless communication system.

The role of airborne radiometric survey in defining the distribution of phosphate rocks in the Syrian desert and the Northern Palmyrides

International Nuclear Information System (INIS)

Jubeli, Y.M.

2000-01-01

Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the Palaeogene phosphate rocks. Another important result to the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data. (author)

Airborne Gravity: NGS' Gravity Data for EN07 (2012-2013)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Maine and Canada collected in 2012 and 2013 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American...

Airborne Gravity: NGS' Gravity Data for AS03 (2010-2012)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2010 and 2012 over 2 surveys. This data set is part of the Gravity for the Re-definition of the American Vertical Datum...

Airborne geophysics in Australia: the government contribution

International Nuclear Information System (INIS)

Denham, D.

1997-01-01

Airborne geophysical data sets provide important cost-effective information for resource exploration and land management. Improved techniques, developed recently, now enable high-resolution aeromagnetic and gamma-ray surveys to be used extensively by the resource industries to improve the cost effectiveness of exploration and by governments to encourage resource development and sustainable management of natural resources. Although airborne geophysical techniques have been used extensively and are now used almost routinely by mineral explorers, it is only in the last few years that governments have been involved as major players in the acquisition of data. The exploration industry pioneered the imaging of high-resolution airborne geophysical data sets in the early 1980s and, at the same time, the Northern Territory Government started a modest program of flying the Northern Territory, at 500 m flight-line spacing, to attract mineral exploration. After the start of the National Geoscience Mapping Accord in 1990, the then BMR and its State/Territory counterparts used the new high-resolution data as an essential ingredient to underpin mapping programs. These new data sets proved so valuable that, starting in 1992/93, the annual expenditure by the Commonwealth and States/Northern Territory increased from roughly $2 million per year to a massive $10 million per year. These investments by governments, although unlikely to be permanently sustainable, have been made to encourage and expand exploration activity by providing new high-quality data sets in industry at very low cost. There are now approximately 11 million line-km of airborne geophysical data available in databases held by the Commonwealth, States and Northern Territory. The results so far have seen a significant increase in exploration activity in States that have embarked on this course (e.g. South Australia and Victoria), and the information provided from these surveys is proving crucial to understanding the

Airborne pollen and spore survey in relation to allergy and plant ...

African Journals Online (AJOL)

Airborne bio-particles of allergic significance were recorded at a height of 15m in Nsukka during September 1999 – February 2000. Spores of fungi and pollen grains, which are important part of the exposure that may lead to allergic discomfort and plant diseases, dominated the particles. Other primary sources of the allergic ...

MERGING AIRBORNE LIDAR DATA AND SATELLITE SAR DATA FOR BUILDING CLASSIFICATION

Directory of Open Access Journals (Sweden)

T. Yamamoto

2015-05-01

Full Text Available A frequent map revision is required in GIS applications, such as disaster prevention and urban planning. In general, airborne photogrammetry and LIDAR measurements are applied to geometrical data acquisition for automated map generation and revision. However, attribute data acquisition and classification depend on manual editing works including ground surveys. In general, airborne photogrammetry and LiDAR measurements are applied to geometrical data acquisition for automated map generation and revision. However, these approaches classify geometrical attributes. Moreover, ground survey and manual editing works are finally required in attribute data classification. On the other hand, although geometrical data extraction is difficult, SAR data have a possibility to automate the attribute data acquisition and classification. The SAR data represent microwave reflections on various surfaces of ground and buildings. There are many researches related to monitoring activities of disaster, vegetation, and urban. Moreover, we have an opportunity to acquire higher resolution data in urban areas with new sensors, such as ALOS2 PALSAR2. Therefore, in this study, we focus on an integration of airborne LIDAR data and satellite SAR data for building extraction and classification.

Airborne gamma-ray spectrometer and magnetometer survey: Barrow Quadrangle, Alaska. Final report. Volume I

International Nuclear Information System (INIS)

1981-03-01

During the months of July-August 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 3 0 x 1 0 and one (1) 4 0 x 1 0 NTMS quadrangles of the Alaskan North Slope. This report discusses the results obtained over the Barrow map area. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps, flight path maps, and computer printer maps. The histograms and the multiparameter profiles are presented with the anomaly maps and flight path map in a separate bound volume. Complete data listings of both the reduced single record and the reduced averaged record data are found in the back of this report. The format of the printout of the microfiches and the format of the data files delivered on magnetic tape are in accordance with the specifications of the BFEC 1200-C and are described in appendices F through L of this report

Interpretation of Airborne Radiometric and Magnetic Data in the ...

African Journals Online (AJOL)

Wadi Millaha area is located in the North Eastern Desert of Egypt. It has been systematically surveyed using airborne gamma-ray spectrometric and magnetic methods. In the present study, the identification of both uranium and thorium anomalies has been mainly based on examining a set of composite spectrometric ...

Airborne Gravity: NGS' Gravity Data for ES05 (2015-2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Florida and the Atlantic Ocean collected in two surveys, FL15-1 and FL15-2. This data set is part of the Gravity for the Re-definition of...

Airborne Gravity: NGS' Gravity Data for AS04 (2015-2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Alaska collected in 2015 and 2016 over 2 surveys, AK15 and AK16. This data set is part of the Gravity for the Re-definition of the American...

Transient ElectroMagnetic and Electric Self-Potential survey in the TAG hydrothermal field in MAR

Science.gov (United States)

Tao, C.; Deng, X.; Wu, G.; Xi, Z.; Zhou, D.; Zuo, L.

2012-12-01

The TAG hydrothermal field is one of the most studied hydrothermal fields. This field covers an area of 5km×5km, which includes low-temperature Mn- and Fe-oxides and nontronites zone, relict massive sulfide mounds as well as active hydrothermal mound(TAG mound) [Thompson, 1985, Rona, 1993]. Drilling program was performed in the ODP (Ocean Drilling Program) Leg 158 in the TAG mound [Humphris, 1996]. In 1996, electrical resistivity survey in the TAG mound was conducted using innovative transient electric dipole-dipole instruments which was carried by DSV 'Alvin' [Cairns et al., 1996, Von Herzen et al., 1996]. In June 2012, the 2nd Leg of the Chinese 26th cruise was carried out in the TAG hydrothermal field at Mid Atlantic Ridge by R/V DAYANGYIHAO. Six TEM (Transient ElectroMagnetic) survey lines were deployed, with four of which across the ODP Leg 158 drilling area. Besides, two SP (Electric Self-Potential) survey lines were across the ODP drilling area. The survey results of TEM preliminary revealed the vertical structure of the TAG hydrothermal field. The survey results of both TEM and SP are consistent with the ODP drilling result, and also agree well with the temperature and water-column anomalies obtained in this leg. Preliminary results show that the TEM and SP methods are capable of revealing the horizontal and vertical distribution of the hydrothermal sulfide fields.

Development of snow water equivalent survey methods using airborne gamma measurements. Research progress, January 1975--September 1975 and suggested directions for future work

International Nuclear Information System (INIS)

Fritzsche, A.; Jupiter, C.

1975-01-01

This is a summary of the progress made during the period March 1975 through September 1975 on EG and G's support of the National Oceanic and Atmospheric Administration for development of airborne techniques for measurement of the water equivalent of snow and soil moisture. The work included a series of snow and soil moisture surveys and development of a new detector and data acquisition system. The status of this work is summarized here together with a review of plans for the immediate future

Performance and non-destructive evaluation methods of airborne radome and stealth structures

Science.gov (United States)

Panwar, Ravi; Ryul Lee, Jung

2018-06-01

In the past few years, great effort has been devoted to the fabrication of highly efficient, broadband radome and stealth (R&S) structures for distinct control, guidance, surveillance and communication applications for airborne platforms. The evaluation of non-planar aircraft R&S structures in terms of their electromagnetic performance and structural damage is still a very challenging task. In this article, distinct measurement techniques are discussed for the electromagnetic performance and non-destructive evaluation (NDE) of R&S structures. This paper deals with an overview of the transmission line method and free space measurement based microwave measurement techniques for the electromagnetic performance evaluation of R&S structures. In addition, various conventional as well as advanced methods, such as millimetre and terahertz wave based imaging techniques with great potential for NDE of load bearing R&S structures, are also discussed in detail. A glimpse of in situ NDE techniques with corresponding experimental setup for R&S structures is also presented. The basic concepts, measurement ranges and their instrumentation, measurement method of different R&S structures and some miscellaneous topics are discussed in detail. Some of the challenges and issues pertaining to the measurement of curved R&S structures are also presented. This study also lists various mathematical models and analytical techniques for the electromagnetic performance evaluation and NDE of R&S structures. The research directions described in this study may be of interest to the scientific community in the aerospace sectors.

Airborne Gravity: NGS' Gravity Data for CS07 (2014 & 2016)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne gravity data for Texas collected in 2014 & 2016 over 3 surveys,TX14-2, TX16-1 and TX16-2. This data set is part of the Gravity for the Re-definition of...

Calibration of angle response of a NaI(Tl) airborne spectrometer to 137Cs and 60Co point sources on the ground

International Nuclear Information System (INIS)

Liu Xinhua; Zhang Yongxing; Gu Renkang; Shen Ensheng

1998-01-01

The angle response function F(φ,θ) is a basic calibration of airborne spectrometers in airborne surveying for nuclear emergency monitoring. The author describes the method and results of angle response function calibration of a NaI(Tl) airborne spectrometer for 137 Cs and 60 Co point sources on the ground, with less than 20% uncertainty. By using the results, the calibration factors of the NaI(Tl) airborne spectrometer fixed in Yun-5 plane at different flying heights are calculated by numerical integral method for 137 Cs uniform area source on ground surface, with less than 25% uncertainty. The minimum detection limits (L D ) are calculated at 90 m and 120 m flying heights in the range of over Shijiazhuang airborne surveying for 137 Cs uniform area source on ground surface to be 3.83 and 5.62 kBq/m 2 , respectively

A literature survey of the biological effects and mechanics of electromagnetic radiation

International Nuclear Information System (INIS)

Zeh, K.A.

1985-01-01

The following report discusses the very controversial subject of electromagnetic interaction with the human body. The project was undertaken in the form of a literature survey to investigate the biological mechanisms responsible for the interaction, the theoretical models and associated mathematical techniques required to model the human body, the resulting energy deposition in the human and the factors which effect this. It was established that at present the most realistic model of man can be obtained using a block model and moment method technique with improved methods such as conjugate gradients or band approximation for the necessary matrix inversion. The impedance method of modelling could be very promising for future research. From the literature studied on biological effects no scientific evidence was found which definitely proves or disproves hazardous effects exist at low field intensities ( -2 ). The testes and the lens of the eye can be harmed, however, if the intensity is sufficient to cause a temperature rise of 1 degree Celsius in these organs

Airborne Compositae dermatitis

DEFF Research Database (Denmark)

Christensen, Lars Porskjær; Jakobsen, Henrik Byrial; Paulsen, E.

1999-01-01

The air around intact feverfew (Tanacetum parthenium) plants was examined for the presence of airborne parthenolide and other potential allergens using a high-volume air sampler and a dynamic headspace technique. No particle-bound parthenolide was detected in the former. Among volatiles emitted f...... for airborne Compositae dermatitis. Potential allergens were found among the emitted monoterpenes and their importance in airborne Compositae dermatitis is discussed....

Introductory study of super survey (next generation underground exploration technology); Super survey (jisedai chika tansa gijutsu) no sendo kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

An investigational study was conducted on the R and D trend of innovative technology aiming at high-accuracy/high-efficiency next generation underground exploration technology (super survey technology). Paying attention to the seismic survey and electromagnetic survey, the study was made on technical characteristics, the utilization status and the needs at sites, the R and D trend, etc. As to the present R and D, the development is proceeded with of the time domain method in the electromagnetic survey, the effective quantity data processing/analysis method and the indication method using the reflection method in the elastic survey. As new technology to be noticed, the following are cited: SQUID magnetometer, underground analysis using magnetic deviation data, electromagnetic migration, ACROSS, rotating seismometer, laser Doppler vibrator, etc. Concerning the course of the next generation underground survey technology, a system of the integrated underground exploration theory is considered which is based on a combination of the electromagnetic survey and seismic exploration. In the study, a plan is worked out for research/development of a technology of analyzing the different data obtained. 49 figs., 13 tabs.

Airborne gamma-ray spectrometer and magnetometer survey: Forsyth quadrangle, Round Up quadrangle, Hardin quadrangle (Montana), Sheridan quadrangle, (Wyoming). Final report

International Nuclear Information System (INIS)

1981-01-01

An airborne combined radiometric and magnetic survey was performed for the Department of Energy (DOE) over the area covered by the Forsyth, Hardin, and Sheridan, and Roundup, 1:250,000 National Topographic Map Series (NTMS), quadrangle maps. The survey was part of DOE's National Uranium Resource Evaluation (NURE) program. Data were collected by a helicopter equipped with a gamma-ray spectrometer with a large crystal volume, and with a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration Pads and the Lake Mead Dynamic Test Range. Data quality was ensured during the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. The anomalies were interpreted and an interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data collection procedures, the data processing procedures, the data presentation, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

Strapdown Airborne Gravimetry Quality Assessment Method Based on Single Survey Line Data: A Study by SGA-WZ02 Gravimeter

Science.gov (United States)

Wu, Meiping; Cao, Juliang; Zhang, Kaidong; Cai, Shaokun; Yu, Ruihang

2018-01-01

Quality assessment is an important part in the strapdown airborne gravimetry. Root mean square error (RMSE) evaluation method is a classical way to evaluate the gravimetry quality, but classical evaluation methods are preconditioned by extra flight or reference data. Thus, a method, which is able to largely conquer the premises of classical quality assessment methods and can be used in single survey line, has been developed in this paper. According to theoretical analysis, the method chooses the stability of two horizontal attitude angles, horizontal specific force and vertical specific force as the determinants of quality assessment method. The actual data, collected by SGA-WZ02 from 13 flights 21 lines in certain survey, was used to build the model and elaborate the method. To substantiate the performance of the quality assessment model, the model is applied in extra repeat line flights from two surveys. Compared with internal RMSE, standard deviation of assessment residuals are 0.23 mGal and 0.16 mGal in two surveys, which shows that the quality assessment method is reliable and stricter. The extra flights are not necessary by specially arranging the route of flights. The method, summarized from SGA-WZ02, is a feasible approach to assess gravimetry quality using single line data and is also suitable for other strapdown gravimeters. PMID:29373535

Airborne Video Surveillance

National Research Council Canada - National Science Library

Blask, Steven

2002-01-01

The DARPA Airborne Video Surveillance (AVS) program was established to develop and promote technologies to make airborne video more useful, providing capabilities that achieve a UAV force multiplier...

Mapping localised freshwater anomalies in the brackish paleo-lake sediments of the Machile–Zambezi Basin with transient electromagnetic sounding, geoelectrical imaging and induced polarisation

DEFF Research Database (Denmark)

Chongo, Mkhuzo; Christiansen, Anders Vest; Fiandaca, Gianluca

2015-01-01

A recent airborne TEM survey in the Machile–Zambezi Basin of south western Zambia revealed high electrical resistivity anomalies (around 100 Ωm) in a low electrical resistivity (below 13 Ωm) background. The near surface (0–40 m depth range) electrical resistivity distribution of these anomalies...... appeared to be coincident with superficial features related to surface water such as alluvial fans and flood plains. This paper describes the application of transient electromagnetic soundings (TEM) and continuous vertical electrical sounding (CVES) using geo-electrics and time domain induced polarisation...... thins out and deteriorates in water quality further inland. It is postulated that the freshwater lens originated as a result of interaction between the Zambezi River and the salty aquifer in a setting in which evapotranspiration is the net climatic stress. Similar high electrical resistivity bodies were...

Airborne gamma anomalies in the Elbe Valley near Koenigstein, Germany - Origin and variation with time

International Nuclear Information System (INIS)

Ruhrmann, G.; Schmeling, B.; Schauer, M.; Gatzweiler, R.

1997-01-01

In 1982, an airborne gamma spectrometer survey was undertaken by SDAG WISMUT which was directed at the detection of further uranium mineralization in Saxony and Thuringia. Anomalies outlined along the Elbe river near the existing Koenigstein uranium mine were attributed to one or a combination of the following causes: radioactive residues from uranium processing facilities located upstream, temporary accumulation of Rn-decay products attached to dust particles in the atmosphere at the time of the survey, and radioactive waters emerging from uraniferous rocks along tectonic structures. In 1994, WISMUT GmbH re-evaluated the survey to determine the need for implementing cleanup measures. Subsequent to the verification of the original airborne data, ground surveys were undertaken that included gamma spectrometry, percussion probing and river sediment sampling. The new results did not confirm the magnitude of most of the 1982 airborne anomalies. The general decline of the radioactivity pointed out by the 1994 ground measurements is interpreted to be a result of the partial erosion and dilution of radionuclides in fluvial sediments as well as burial by additional river sediments since. Additional anomalous copper and zinc concentrations are attributed to sources other than mining. The ground follow-up delineated a new anomalous zone that is caused by radionuclides discharged with treated process and mine water. It is the only area, which may require further investigations and possible remedial action. (author)

Ground-Truthing of Airborne LiDAR Using RTK-GPS Surveyed Data in Coastal Louisiana's Wetlands

Science.gov (United States)

Lauve, R. M.; Alizad, K.; Hagen, S. C.

2017-12-01

Airborne LiDAR (Light Detection and Ranging) data are used by engineers and scientists to create bare earth digital elevation models (DEM), which are essential to modeling complex coastal, ecological, and hydrological systems. However, acquiring accurate bare earth elevations in coastal wetlands is difficult due to the density of marsh grasses that prevent the sensors reflection off the true ground surface. Previous work by Medeiros et al. [2015] developed a technique to assess LiDAR error and adjust elevations according to marsh vegetation density and index. The aim of this study is the collection of ground truth points and the investigation on the range of potential errors found in existing LiDAR datasets within coastal Louisiana's wetlands. Survey grids were mapped out in an area dominated by Spartina alterniflora and a survey-grade Trimble Real Time Kinematic (RTK) GPS device was employed to measure bare earth ground elevations in the marsh system adjacent to Terrebonne Bay, LA. Elevations were obtained for 20 meter-spaced surveyed grid points and were used to generate a DEM. The comparison between LiDAR derived and surveyed data DEMs yield an average difference of 23 cm with a maximum difference of 68 cm. Considering the local tidal range of 45 cm, these differences can introduce substantial error when the DEM is used for ecological modeling [Alizad et al., 2016]. Results from this study will be further analyzed and implemented in order to adjust LiDAR-derived DEMs closer to their true elevation across Louisiana's coastal wetlands. ReferencesAlizad, K., S. C. Hagen, J. T. Morris, S. C. Medeiros, M. V. Bilskie, and J. F. Weishampel (2016), Coastal wetland response to sea-level rise in a fluvial estuarine system, Earth's Future, 4(11), 483-497, 10.1002/2016EF000385. Medeiros, S., S. Hagen, J. Weishampel, and J. Angelo (2015), Adjusting Lidar-Derived Digital Terrain Models in Coastal Marshes Based on Estimated Aboveground Biomass Density, Remote Sensing, 7

The History of Electromagnetic Induction Techniques in Soil Survey

Science.gov (United States)

Brevik, Eric C.; Doolittle, Jim

2014-05-01

Electromagnetic induction (EMI) has been used to characterize the spatial variability of soil properties since the late 1970s. Initially used to assess soil salinity, the use of EMI in soil studies has expanded to include: mapping soil types; characterizing soil water content and flow patterns; assessing variations in soil texture, compaction, organic matter content, and pH; and determining the depth to subsurface horizons, stratigraphic layers or bedrock, among other uses. In all cases the soil property being investigated must influence soil apparent electrical conductivity (ECa) either directly or indirectly for EMI techniques to be effective. An increasing number and diversity of EMI sensors have been developed in response to users' needs and the availability of allied technologies, which have greatly improved the functionality of these tools. EMI investigations provide several benefits for soil studies. The large amount of georeferenced data that can be rapidly and inexpensively collected with EMI provides more complete characterization of the spatial variations in soil properties than traditional sampling techniques. In addition, compared to traditional soil survey methods, EMI can more effectively characterize diffuse soil boundaries and identify included areas of dissimilar soils within mapped soil units, giving soil scientists greater confidence when collecting spatial soil information. EMI techniques do have limitations; results are site-specific and can vary depending on the complex interactions among multiple and variable soil properties. Despite this, EMI techniques are increasingly being used to investigate the spatial variability of soil properties at field and landscape scales.

Airborne gamma-radiation snow water-equivalent and soil-moisture measurements and satellite areal extent of snow-cover measurements. A user's guide. Version 3.0

International Nuclear Information System (INIS)

Carroll, T.; Allen, M.

1988-01-01

The National Remote Sensing Hydrology Program is managed by the Office of Hydrology and consists of the Airborne Snow Survey Section and the Satellite Hydrology Section. The Airborne Snow Survey Section makes airborne snow water-equivalent and soil-moisture measurements over large areas of the country subject to a severe and chronic snowmelt flooding threat. The User's Guide is intended primarily to provide field hydrologists with some background on the technical and administrative aspects of the National Remote Sensing Hydrology Program. The guide summarizes the techniques and procedures used to make and distribute real-time, operational airborne snow water-equivalent measurements and satellite areal extent of snow-cover measurements made over large areas of the country. The current airborne and satellite databases are summarized, and procedures to access the real-time observations through both AFOS and through a commercial, electronic bulletin board system are given in the appendices

Monte Carlo Simulation of the Echo Signals from Low-Flying Targets for Airborne Radar

Directory of Open Access Journals (Sweden)

Mingyuan Man

2014-01-01

Full Text Available A demonstrated hybrid method based on the combination of half-space physical optics method (PO, graphical-electromagnetic computing (GRECO, and Monte Carlo method on echo signals from low-flying targets based on actual environment for airborne radar is presented in this paper. The half-space physical optics method , combined with the graphical-electromagnetic computing (GRECO method to eliminate the shadow regions quickly and rebuild the target automatically, is employed to calculate the radar cross section (RCS of the conductive targets in half space fast and accurately. The direct echo is computed based on the radar equation. The reflected paths from sea or ground surface cause multipath effects. In order to accurately obtain the echo signals, the phase factors are modified for fluctuations in multipath, and the statistical average value of the echo signals is obtained using the Monte Carlo method. A typical simulation is performed, and the numerical results show the accuracy of the proposed method.

An airborne gamma ray survey of parts of SW Scotland in February 1993. Final Report

International Nuclear Information System (INIS)

Sanderson, D.C.W.; Allyson, J.D.; Tyler, A.N.; Ni Riain, S.; Murphy, S.

1994-01-01

An airborne gamma ray survey was conducted for the Scottish Office Environment Department of coastal and inland parts of SW Scotland to define existing background levels, to locate features worthy of further attention, and to demonstrate the emergency response capabilities of radiometric methods. Coastal areas were surveyed with 500 m line spacing. Inland areas were specified to 2 km line spacing, however it was possible to achieve 1 km line spacing in the majority of the inland zone. The radiometric maps show clearly the distributions of each individual nuclide and indicate the contribution which individual localised features make to the overall gamma ray dose rate. Naturally occurring nuclides reflect the underlying geological and geomorphological contexts of the landscapes. The main granite intrusions, most notably at Cairnsmore of Fleet, the Loch Doon Granodiorite, Glencairn of Carsphairn, the Dalbeattie granite, and Criffel Pluton are readily visible in 40 K, 214 Bi and 208 Tl maps, and control their local radiation environments. A number of areas of enhanced 214 Bi, which may reflect radon potential, were noted. A transient radon associated 214 Bi signal was observed on the west of the Wigtown peninsular during the survey. Examination of spectral data in the vicinity Dundrennan has confirmed that there is no evidence of widespread terrestrial contamination arising from the use of depleted uranium projectiles on the range. The 137 Cs map indicates the environmental distribution of this nuclide in considerable detail. Levels of 137 Cs range from approximately 2 kBq m -2 , a level consistent with global weapons' testing fallout, from 2-40 kBq m -2 on terrestrial sites affected by deposition from the Chernobyl accident, and from 40 kBq m -2 to over 200 kBq m -2 on tide washed pastures which have accumulated marine sediments from the Irish sea. (author)

Electromagnetic wave survey on voids behind waterway channel lining; Suiro kaikyo sokuheki haimen kudo no denjiha tansa

Energy Technology Data Exchange (ETDEWEB)

Koitabashi, H [Tokyo Electric Power Co. Inc., Tokyo (Japan); Inagaki, M

1996-10-01

Voids behind lining were surveyed by applying electromagnetic wave reflection method to the waterway channel of a hydraulic power plant. Since waterway channel lining is ranged from oblique to vertical direction, voids are hardly formed. However, formation of voids or cavities behind lining is supposed such as voids between ground and lining due to change with time or consolidation settlement, and voids due to soil loss. Electromagnetic radar reflection suggesting continuous void was observed behind terrace concrete lining. As the result of core boring, thin continuous void of 2-5cm thick and more than 100m long was found. This was possibly formed by consolidation settlement for a long time. In some sites, continuous void signal was observed at the upper part of side walls although this signal was smaller than that at the upper part of a terrace. This continuous cavity of 10-20cm thick and 20m long was different from voids, and unevenly distributed at the upper part of an open channel along flowing surface with large flow rate. In addition, it is necessary to clarify the relation to cracks. 2 refs., 4 figs.

King George Island ice cap geometry updated with airborne GPR measurements

Directory of Open Access Journals (Sweden)

M. Rückamp

2012-07-01

Full Text Available Ice geometry is a mandatory requirement for numerical modelling purposes. In this paper we present a consistent data set for the ice thickness, the bedrock topography and the ice surface topography of the King George Island ice cap (Arctowski icefield and the adjacent central part. The new data set is composed of ground based and airborne ground penetrating radar (GPR and differential GPS (DGPS measurements, obtained during several field campaigns. Blindow et al. (2010 already provided a comprehensive overview of the ground based measurements carried out in the safely accessible area of the ice cap. The updated data set incorporates airborne measurements in the heavily crevassed coastal areas. Therefore, in this paper special attention is paid to the airborne measurements by addressing the instrument used, survey procedure, and data processing in more detail. In particular, the inclusion of airborne GPR measurements with the 30 MHz BGR-P30-System developed at the Institute of Geophysics (University of Münster completes the picture of the ice geometry substantially. The compiled digital elevation model of the bedrock shows a rough, highly variable topography with pronounced valleys, ridges, and troughs. Mean ice thickness is 240 ± 6 m, with a maximum value of 422 ± 10 m in the surveyed area. Noticeable are bounded areas in the bedrock topography below sea level where marine based ice exists. The provided data set is required as a basis for future monitoring attempts or as input for numerical modelling experiments. The data set is available from the PANGAEA database at http://dx.doi.org/10.1594/PANGAEA.770567.

The Bolmen tunnel project - evaluation of geophysical site investigation methods

International Nuclear Information System (INIS)

Stanfors, R.

1987-12-01

The report presents geophysical measurements along and adjacent to the tunnel and an evaluation of the ability of the various methods to permit prediction of rock mass parameters of significance to stability and water bearing ability. The evaluation shows that, using airborne electro-magnetic surveys, it was possible to indicate about 80% of alla the zones of weakness more than 50 m wide in the tunnel. Airborne magnetic surveys located about 90% of all dolerite dykes more than 10 m wide. Ground-level VLF and Slingram methods of electro-magnetic measurement indicated 75% and 85% respectively of all zones of weakness more than 50 m wide. Resistivity methods were successfully used to locate clay filled and water-bearing fracture zones. About 75% of the length of tunnel over which resistivity values below 500 ohm m were measured required shotcrete support and pre-grouting. (orig./DG)

Biological effects from electromagnetic fields: Research progress and exposure measurements

International Nuclear Information System (INIS)

Mauro, F.; Lovisolo, G.A.; Raganella, L.

1992-01-01

Although it is commonly accepted that exposure to high levels of electromagnetic, micro- and radiofrequency waves produces harmful effects to the health of man, the formulation of exposure limits is still an open process and dependent upon the evolving level of knowledge in this field. This paper surveys the current level of knowledge gained through 'in vitro' and 'in vivo' radiological and epidemiological studies on different types of electromagnetic radiation derived effects - chromosomal, mutagenic, carcinogenic. It then reviews efforts by international organizations, e. g., the International Radiation Protection Association, to establish exposure limits for radiofrequency electromagnetic fields. Brief notes are given on the electromagnetic radiation monitoring campaign being performed by public health authorities in the Lazio Region of Italy

Advances and Best Practices in Airborne Gravimetry from the U.S. GRAV-D Project

Science.gov (United States)

Diehl, Theresa; Childers, Vicki; Preaux, Sandra; Holmes, Simon; Weil, Carly

2013-04-01

The Gravity for the Redefinition of the American Vertical Datum (GRAV-D) project, an official policy of the U.S. National Geodetic Survey as of 2007, is working to survey the entire U.S. and its holdings with high-altitude airborne gravimetry. The goal of the project is to provide a consistent, high-quality gravity dataset that will become the cornerstone of a new gravimetric geoid and national vertical datum in 2022. Over the last five years, the GRAV-D project has surveyed more than 25% of the country, accomplishing almost 500 flights on six different aircraft platforms and producing more than 3.7 Million square km of data thus far. This wealth of experience has led to advances in the collection, processing, and evaluation of high-altitude (20,000 - 35,000 ft) airborne gravity data. This presentation will highlight the most important practical and theoretical advances of the GRAV-D project, giving an introduction to each. Examples of innovation include: 1. Use of navigation grade inertial measurement unit data and precise lever arm measurements for positioning; 2. New quality control tests and software for near real-time analysis of data in the field; 3. Increased accuracy of gravity post-processing by reexamining assumptions and simplifications that were inconsistent with a goal of 1 mGal precision; and 4. Better final data evaluation through crossovers, additional statistics, and inclusion of airborne data into harmonic models that use EGM08 as a base model. The increases in data quality that resulted from implementation of the above advances (and others) will be shown with a case study of the GRAV-D 2008 southern Alaska survey near Anchorage, over Cook Inlet. The case study's statistics and comparisons to global models illustrate the impact that these advances have had on the final airborne gravity data quality. Finally, the presentation will summarize the best practices identified by the project from its last five years of experience.

Volumetric evolution of Surtsey, Iceland, from topographic maps and scanning airborne laser altimetry

Science.gov (United States)

Garvin, J.B.; Williams, R.S.; Frawley, J.J.; Krabill, W.B.

2000-01-01

The volumetric evolution of Surtsey has been estimated on the basis of digital elevation models derived from NASA scanning airborne laser altimeter surveys (20 July 1998), as well as digitized 1:5,000-scale topographic maps produced by the National Land Survey of Iceland and by Norrman. Subaerial volumes have been computed from co-registered digital elevation models (DEM's) from 6 July 1968, 11 July 1975, 16 July 1993, and 20 July 1998 (scanning airborne laser altimetry), as well as true surface area (above mean sea level). Our analysis suggests that the subaerial volume of Surtsey has been reduced from nearly 0.100 km3 on 6 July 1968 to 0.075 km3 on 20 July 1998. Linear regression analysis of the temporal evolution of Surtsey's subaerial volume indicates that most of its subaerial surface will be at or below mean sea-level by approximately 2100. This assumes a conservative estimate of continuation of the current pace of marine erosion and mass-wasting on the island, including the indurated core of the conduits of the Surtur I and Surtur II eruptive vents. If the conduits are relatively resistant to marine erosion they will become sea stacks after the rest of the island has become a submarine shoal, and some portions of the island could survive for centuries. The 20 July 1998 scanning laser altimeter surveys further indicate rapid enlargement of erosional canyons in the northeastern portion of the partial tephra ring associated with Surtur I. Continued airborne and eventually spaceborne topographic surveys of Surtsey are planned to refine the inter-annual change of its subaerial volume.

On the Atmospheric Correction of Antarctic Airborne Hyperspectral Data

Directory of Open Access Journals (Sweden)

Martin Black

2014-05-01

Full Text Available The first airborne hyperspectral campaign in the Antarctic Peninsula region was carried out by the British Antarctic Survey and partners in February 2011. This paper presents an insight into the applicability of currently available radiative transfer modelling and atmospheric correction techniques for processing airborne hyperspectral data in this unique coastal Antarctic environment. Results from the Atmospheric and Topographic Correction version 4 (ATCOR-4 package reveal absolute reflectance values somewhat in line with laboratory measured spectra, with Root Mean Square Error (RMSE values of 5% in the visible near infrared (0.4–1 µm and 8% in the shortwave infrared (1–2.5 µm. Residual noise remains present due to the absorption by atmospheric gases and aerosols, but certain parts of the spectrum match laboratory measured features very well. This study demonstrates that commercially available packages for carrying out atmospheric correction are capable of correcting airborne hyperspectral data in the challenging environment present in Antarctica. However, it is anticipated that future results from atmospheric correction could be improved by measuring in situ atmospheric data to generate atmospheric profiles and aerosol models, or with the use of multiple ground targets for calibration and validation.

Hydrostratigraphic modelling using multiple-point statistics and airborne transient electromagnetic methods

DEFF Research Database (Denmark)

Barfod, Adrian; Straubhaar, Julien; Høyer, Anne-Sophie

2017-01-01

the incorporation of elaborate datasets and provides a framework for stochastic hydrostratigraphic modelling. This paper focuses on comparing three MPS methods: snesim, DS and iqsim. The MPS methods are tested and compared on a real-world hydrogeophysical survey from Kasted in Denmark, which covers an area of 45 km......2. The comparison of the stochastic hydrostratigraphic MPS models is carried out in an elaborate scheme of visual inspection, mathematical similarity and consistency with boreholes. Using the Kasted survey data, a practical example for modelling new survey areas is presented. A cognitive...

Hydrographic & Topographic LIDAR Acquisition, Northwest Coast, Washington State - Bathymetric Survey Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data were collected by the SHOALS-1000T(Scanning Hydrographic Operational Airborne Lidar Survey)system which consists of an airborne laser transmitter/receiver...

Bedrock morphology and structure, upper Santa Cruz Basin, south-central Arizona, with transient electromagnetic survey data

Science.gov (United States)

Bultman, Mark W.; Page, William R.

2016-10-31

The upper Santa Cruz Basin is an important groundwater basin containing the regional aquifer for the city of Nogales, Arizona. This report provides data and interpretations of data aimed at better understanding the bedrock morphology and structure of the upper Santa Cruz Basin study area which encompasses the Rio Rico and Nogales 1:24,000-scale U.S. Geological Survey quadrangles. Data used in this report include the Arizona Aeromagnetic and Gravity Maps and Data referred to here as the 1996 Patagonia Aeromagnetic survey, Bouguer gravity anomaly data, and conductivity-depth transforms (CDTs) from the 1998 Santa Cruz transient electromagnetic survey (whose data are included in appendixes 1 and 2 of this report).Analyses based on magnetic gradients worked well to identify the range-front faults along the Mt. Benedict horst block, the location of possibly fault-controlled canyons to the west of Mt. Benedict, the edges of buried lava flows, and numerous other concealed faults and contacts. Applying the 1996 Patagonia aeromagnetic survey data using the horizontal gradient method produced results that were most closely correlated with the observed geology.The 1996 Patagonia aeromagnetic survey was used to estimate depth to bedrock in the upper Santa Cruz Basin study area. Three different depth estimation methods were applied to the data: Euler deconvolution, horizontal gradient magnitude, and analytic signal. The final depth to bedrock map was produced by choosing the maximum depth from each of the three methods at a given location and combining all maximum depths. In locations of rocks with a known reversed natural remanent magnetic field, gravity based depth estimates from Gettings and Houser (1997) were used.The depth to bedrock map was supported by modeling aeromagnetic anomaly data along six profiles. These cross sectional models demonstrated that by using the depth to bedrock map generated in this study, known and concealed faults, measured and estimated magnetic

Airborne gamma-ray spectrometer and magnetometer survey: Crescent Quadrangle, Burns Quadrangle, Canyon City Quadrangle, Bend Quadrangle, Salem Quadrangle (Oregon). Final report

International Nuclear Information System (INIS)

1981-01-01

An airborne combining radiometric and magnetic survey was performed for the Department of Energy over the area covered by the Burns, Crescent, Canyon City, Bend, and Salem, Washington 1:250,000 National Topographic Map Series, 1 0 x 2 0 quadrangle maps. The survey was a part of DOE's National Aerial Radiometric Reconnaissance program, which is in turn a part of the National Uranium Resource Evaluation program. Data were collected by a helicopter equipped with a gamma-ray spectrometer having a large crystal volume, and a high sensitivity proton precession magnetometer. The radiometric system was calibrated at the Walker Field Calibration pads and the Lake Mead Dynamic Test range. Data quality was ensured throughout the survey by daily test flights and equipment checks. Radiometric data were corrected for live time, aircraft and equipment background, cosmic background, atmospheric radon, Compton scatter, and altitude dependence. The corrected data were statistically evaluated, plotted, and contoured to produce anomaly maps based on the radiometric response of individual geological units. These maps were interpreted and an anomaly interpretation map produced. Volume I contains a description of the systems used in the survey, a discussion of the calibration of the systems, the data processing procedures, the data display format, the interpretation rationale, and the interpretation methodology. A separate Volume II for each quadrangle contains the data displays and the interpretation results

Strapdown Airborne Gravimetry Using a Combination of Commercial Software and Stable-Platform Gravity Estimates

DEFF Research Database (Denmark)

Jensen, Tim E.; Nielsen, J. Emil; Olesen, Arne V.

2017-01-01

into the long-wavelengths of the gravity estimates. This has made the stable-platform approach the preferred method for geodetic applications. In the summer of 2016, during a large airborne survey in Malaysia, a SIMU system was flown alongside a traditional LaCoste&Romberg (LCR) gravimeter. The SIMU......For the past two decades, airborne gravimetry using a Strapdown Inertial Measurement Unit (SIMU) has been producing gravity estimates comparable to the traditional stable-platform single-axis gravimeters. The challenge has been to control the long term drift of the IMU sensors, propagating...

RESUME 95. Rapid environmental surveying using mobile equipment

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The RESUME95 exercise - Rapid Environmental Surveying Using Mobile Equipment, took place in Finland in August 1995. The objectives of the RESUME exercise were to compare different monitoring systems when used under the same conditions as well as to compare results from similar systems with different data analysis and presentation software. Another objective was to acquire some basic knowledge to standardize and cross calibrate the European air-borne gamma-ray surveying capability so that the results from different systems could be directly comparable. The exercise involved 10 airborn monitoring teams, 7 teams with vehicle monitoring systems as well as ground survey teams from 8 countries. Most systems incorporated GPS satellite navigational aids and computers for real time display of the data which was also recorded for post flight analysis. Most of the car- and airborne systems were based on Nal detectors whereas most of the In-situ systems and a few airborne systems were based on HpGe detectors. The exercise took place in an area near Lahti. Three different areas were surveyed. These were 1) An airfield near Vesivehmaa, which was intended as a calibration site. Soil samples had been taken previously and used to establish the {sup 137}Cs activity of the soil as well as the activity of the natural radioactivity elements {sup 40}K, {sup 214}Bi and {sup 208}Tl. 2) An area contaminated by the Chernobyl nuclear accident, Area II. This area was intended to test the capabilities of the car- and airborne teams for mapping {sup 137}Cs. A number of predefined points in the area were used by In-situ teams. 3) An area with a variety of hidden readioactive sources, Area III. These sources of {sup 60}Co, {sup 137}Cs, {sup 192}Lr and {sup 99}Tc ranged in activity from 0.6 mCi to 15 Ci and was used to test the capability of the different air-borne teams for locating lost radioactive sources. (EG).

RESUME 95. Rapid environmental surveying using mobile equipment

International Nuclear Information System (INIS)

1997-01-01

The RESUME95 exercise - Rapid Environmental Surveying Using Mobile Equipment, took place in Finland in August 1995. The objectives of the RESUME exercise were to compare different monitoring systems when used under the same conditions as well as to compare results from similar systems with different data analysis and presentation software. Another objective was to acquire some basic knowledge to standardize and cross calibrate the European air-borne gamma-ray surveying capability so that the results from different systems could be directly comparable. The exercise involved 10 airborn monitoring teams, 7 teams with vehicle monitoring systems as well as ground survey teams from 8 countries. Most systems incorporated GPS satellite navigational aids and computers for real time display of the data which was also recorded for post flight analysis. Most of the car- and airborne systems were based on Nal detectors whereas most of the In-situ systems and a few airborne systems were based on HpGe detectors. The exercise took place in an area near Lahti. Three different areas were surveyed. These were 1) An airfield near Vesivehmaa, which was intended as a calibration site. Soil samples had been taken previously and used to establish the 137 Cs activity of the soil as well as the activity of the natural radioactivity elements 40 K, 214 Bi and 208 Tl. 2) An area contaminated by the Chernobyl nuclear accident, Area II. This area was intended to test the capabilities of the car- and airborne teams for mapping 137 Cs. A number of predefined points in the area were used by In-situ teams. 3) An area with a variety of hidden readioactive sources, Area III. These sources of 60 Co, 137 Cs, 192 Lr and 99 Tc ranged in activity from 0.6 mCi to 15 Ci and was used to test the capability of the different air-borne teams for locating lost radioactive sources. (EG)

RESUME 95. Rapid environmental surveying using mobile equipment

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

The RESUME95 exercise - Rapid Environmental Surveying Using Mobile Equipment, took place in Finland in August 1995. The objectives of the RESUME exercise were to compare different monitoring systems when used under the same conditions as well as to compare results from similar systems with different data analysis and presentation software. Another objective was to acquire some basic knowledge to standardize and cross calibrate the European air-borne gamma-ray surveying capability so that the results from different systems could be directly comparable. The exercise involved 10 airborn monitoring teams, 7 teams with vehicle monitoring systems as well as ground survey teams from 8 countries. Most systems incorporated GPS satellite navigational aids and computers for real time display of the data which was also recorded for post flight analysis. Most of the car- and airborne systems were based on Nal detectors whereas most of the In-situ systems and a few airborne systems were based on HpGe detectors. The exercise took place in an area near Lahti. Three different areas were surveyed. These were 1) An airfield near Vesivehmaa, which was intended as a calibration site. Soil samples had been taken previously and used to establish the {sup 137}Cs activity of the soil as well as the activity of the natural radioactivity elements {sup 40}K, {sup 214}Bi and {sup 208}Tl. 2) An area contaminated by the Chernobyl nuclear accident, Area II. This area was intended to test the capabilities of the car- and airborne teams for mapping {sup 137}Cs. A number of predefined points in the area were used by In-situ teams. 3) An area with a variety of hidden readioactive sources, Area III. These sources of {sup 60}Co, {sup 137}Cs, {sup 192}Lr and {sup 99}Tc ranged in activity from 0.6 mCi to 15 Ci and was used to test the capability of the different air-borne teams for locating lost radioactive sources. (EG).

Environmental radioactivity in the UK: the airborne geophysical view of dose rate estimates

International Nuclear Information System (INIS)

Beamish, David

2014-01-01

This study considers UK airborne gamma-ray data obtained through a series of high spatial resolution, low altitude surveys over the past decade. The ground concentrations of the naturally occurring radionuclides Potassium, Thorium and Uranium are converted to air absorbed dose rates and these are used to assess terrestrial exposure levels from both natural and technologically enhanced sources. The high resolution airborne information is also assessed alongside existing knowledge from soil sampling and ground-based measurements of exposure levels. The surveys have sampled an extensive number of the UK lithological bedrock formations and the statistical information provides examples of low dose rate lithologies (the formations that characterise much of southern England) to the highest sustained values associated with granitic terrains. The maximum dose rates (e.g. >300 nGy h −1 ) encountered across the sampled granitic terrains are found to vary by a factor of 2. Excluding granitic terrains, the most spatially extensive dose rates (>50 nGy h −1 ) are found in association with the Mercia Mudstone Group (Triassic argillaceous mudstones) of eastern England. Geological associations between high dose rate and high radon values are also noted. Recent studies of the datasets have revealed the extent of source rock (i.e. bedrock) flux attenuation by soil moisture in conjunction with the density and porosity of the temperate latitude soils found in the UK. The presence or absence of soil cover (and associated presence or absence of attenuation) appears to account for a range of localised variations in the exposure levels encountered. The hypothesis is supported by a study of an extensive combined data set of dose rates obtained from soil sampling and by airborne geophysical survey. With no attenuation factors applied, except those intrinsic to the airborne estimates, a bias to high values of between 10 and 15 nGy h −1 is observed in the soil data. A wide range of

An analysis of the lithology to resistivity relationships using airborne EM and boreholes

DEFF Research Database (Denmark)

Barfod, Adrian A.S.; Christiansen, Anders Vest; Møller, Ingelise

2014-01-01

We present a study of the relationship between dense airborne skyTEM resistivity data and sparse lithological borehole data. Understanding the resistivity structure of the subsurface is of great importance to hydrogeological surveys and to ensure a high standard for groundwater quality. Borehole ...

Final Report DE-EE0005380: Assessment of Offshore Wind Farm Effects on Sea Surface, Subsurface and Airborne Electronic Systems

Energy Technology Data Exchange (ETDEWEB)

Ling, Hao [The University of Texas at Austin; Hamilton, Mark F. [The University of Texas at Austin Applied Research Laboratories; Bhalla, Rajan [Science Applications International Corporation; Brown, Walter E. [The University of Texas at Austin Applied Research Laboratories; Hay, Todd A. [The University of Texas at Austin Applied Research Laboratories; Whitelonis, Nicholas J. [The University of Texas at Austin; Yang, Shang-Te [The University of Texas at Austin; Naqvi, Aale R. [The University of Texas at Austin

2013-09-30

Offshore wind energy is a valuable resource that can provide a significant boost to the US renewable energy portfolio. A current constraint to the development of offshore wind farms is the potential for interference to be caused by large wind farms on existing electronic and acoustical equipment such as radar and sonar systems for surveillance, navigation and communications. The US Department of Energy funded this study as an objective assessment of possible interference to various types of equipment operating in the marine environment where offshore wind farms could be installed. The objective of this project was to conduct a baseline evaluation of electromagnetic and acoustical challenges to sea surface, subsurface and airborne electronic systems presented by offshore wind farms. To accomplish this goal, the following tasks were carried out: (1) survey electronic systems that can potentially be impacted by large offshore wind farms, and identify impact assessment studies and research and development activities both within and outside the US, (2) engage key stakeholders to identify their possible concerns and operating requirements, (3) conduct first-principle modeling on the interactions of electromagnetic signals with, and the radiation of underwater acoustic signals from, offshore wind farms to evaluate the effect of such interactions on electronic systems, and (4) provide impact assessments, recommend mitigation methods, prioritize future research directions, and disseminate project findings. This report provides a detailed description of the methodologies used to carry out the study, key findings of the study, and a list of recommendations derived based the findings.

The challenge of uranium exploration

International Nuclear Information System (INIS)

Fountain, D.K.

1982-06-01

The first uranium discoveries at Beaverlodge were made using simple radiometric methods: hand-held geiger counters. Since then techniques of uranium exploration have evolved through airborne radiometric surveys, tracking glacial boulder trains to their origins, and electromagnetic surveys to detect graphite associated with buried uranium deposits. Simple radiometric surveys can cost around $1 000. per day, while testing for deposits at depths of over 400 meters will cost more than $60 000. per drill hole

Airborne gamma-ray spectrometry data processing using 1.5D inversion.

Science.gov (United States)

Druker, Eugene

2017-10-01

Standard processing of Airborne Gamma-Ray Spectrometry data generally gives good results when the measurement conditions are almost constant within several footprint area sizes, with the possible exception of flight height variations in a small range. In practice, deviations, such as large or abrupt changes of flight height and/or rugged terrain are not so rare and lead to certain problems. This article proposes a different approach where the solutions of inverse problems are used for data processing. The approach is quite natural in the processing of field data measured along the flight lines: it explicitly takes into account 1.5D survey models and flight parameters - from topography to sources distribution on the surface. Also, it clearly demonstrates that the inverse problem of the Airborne Gamma-Ray Spectrometry does not have a unique solution. This feature can be used in accordance with the underlying geological problem since various formulations of inverse problems can lead to various geological solutions. The use of the approach is illustrated by several examples given for flight lines and survey areas. This approach can be particularly useful in situations where geological, geophysical and/or geographic survey conditions are far from the standard assumptions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterizing exposures to airborne metals and nanoparticle emissions in a refinery.

Science.gov (United States)

Miller, Arthur; Drake, Pamela L; Hintz, Patrick; Habjan, Matt

2010-07-01

An air quality survey was conducted at a precious metals refinery in order to evaluate worker exposures to airborne metals and to provide detailed characterization of the aerosols. Two areas within the refinery were characterized: a furnace room and an electro-refining area. In line with standard survey practices, both personal and area air filter samples were collected on 37-mm filters and analyzed for metals by inductively coupled plasma-atomic emission spectroscopy. In addition to the standard sampling, measurements were conducted using other tools, designed to provide enhanced characterization of the workplace aerosols. The number concentration and number-weighted particle size distribution of airborne particles were measured with a fast mobility particle sizer (FMPS). Custom-designed software was used to correlate particle concentration data with spatial location data to generate contour maps of particle number concentrations in the work areas. Short-term samples were collected in areas of localized high concentrations and analyzed using transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS) to determine particle morphology and elemental chemistry. Analysis of filter samples indicated that all of the workers were exposed to levels of silver above the Occupational Safety and Health Administration permissible exposure limit of 0.01 mg m(-3) even though the localized ventilation was functioning. Measurements with the FMPS indicated that particle number concentrations near the furnace increased up to 1000-fold above the baseline during the pouring of molten metal. Spatial mapping revealed localized elevated particle concentrations near the furnaces and plumes of particles rising into the stairwells and traveling to the upper work areas. Results of TEM/EDS analyses confirmed the high number of nanoparticles measured by the FMPS and indicated the aerosols were rich in metals including silver, lead, antimony, selenium, and zinc. Results of

Electromagnetic topology: Characterization of internal electromagnetic coupling

Science.gov (United States)

Parmantier, J. P.; Aparicio, J. P.; Faure, F.

1991-01-01

The main principles are presented of a method dealing with the resolution of electromagnetic internal problems: Electromagnetic Topology. A very interesting way is to generalize the multiconductor transmission line network theory to the basic equation of the Electromagnetic Topology: the BLT equation. This generalization is illustrated by the treatment of an aperture as a four port junction. Analytical and experimental derivations of the scattering parameters are presented. These concepts are used to study the electromagnetic coupling in a scale model of an aircraft, and can be seen as a convenient means to test internal electromagnetic interference.

Integrating electromagnetic radiation hazard info the unique occupational risk assessment document

International Nuclear Information System (INIS)

Demaret, P.; Donati, P.

2011-01-01

The number of industrial applications involving electromagnetic waves has significantly increased in recent years. These applications are likely to expose operators to electromagnetic fields exceeding the limits laid down by European Parliament and Council Directive 2004/40/CE of 29 April 2004. A survey has identified the equipment emitting the most radiation and this has been classified into 8 families: resistance welding, magnetization, induction heating, magneto-scopy, dielectric loss welding, electrolysis, magnetic resonance imagery, microwaves. The equipment numbers per family was estimated by a market surveys, which specifically identified several tens of thousands of resistance welding- or magnetization-type machines. This survey enabled us to deduce that at least 100,000 operators in France would be at risk of exposure to electromagnetic fields. An assessment of exposure levels for operators at their workstations was undertaken for each equipment family. A group comprising specialists from INRS and the 9 CARSAT/CRAM Physical Measurement Centres measured electromagnetic fields at 635 workstations fitted with radiation emitting machinery. For each measurement, a severity index corresponding to the ratio of the measured value to the action-triggering value (ATV) recommended by European Parliament and Council Directive 2004/40/CE of 29 April 2004 was calculated. The results show that, for 7 equipment families out of the 8 retained, 25 - 50% of measurements gave electromagnetic field values exceeding the corresponding ATV. These results demonstrate the need for prevention means. In most cases, exposure reduction is achieved by moving the workstation away from the radiation source. Technical solutions do exist for certain equipments, such as shielding for microwave ovens and high-frequency presses, a grounding pad for tarpaulin welding, etc. (authors)

Airborne radionuclide waste-management reference document

International Nuclear Information System (INIS)

Brown, R.A.; Christian, J.D.; Thomas, T.R.

1983-07-01

This report provides the detailed data required to develop a strategy for airborne radioactive waste management by the Department of Energy (DOE). The airborne radioactive materials of primary concern are tritium (H-3), carbon-14 (C-14), krypton-85 (Kr-85), iodine-129 (I-129), and radioactive particulate matter. The introductory section of the report describes the nature and broad objectives of airborne waste management. The relationship of airborne waste management to other waste management programs is described. The scope of the strategy is defined by considering all potential sources of airborne radionuclides and technologies available for their management. Responsibilities of the regulatory agencies are discussed. Section 2 of this document deals primarily with projected inventories, potential releases, and dose commitments of the principal airborne wastes from the light water reactor (LWR) fuel cycle. In Section 3, dose commitments, technologies, costs, regulations, and waste management criteria are analyzed. Section 4 defines goals and objectives for airborne waste management

Neah Bay to Cape Alava, Northwest Coast, Washington State - Topographic Survey Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data were collected by the SHOALS-1000T(Scanning Hydrographic Operational Airborne Lidar Survey)system which consists of an airborne laser transmitter/receiver...

Aerogeophysical survey in Olkiluoto 2009

International Nuclear Information System (INIS)

Kurimo, M.

2009-08-01

This report describes the survey operation, survey and processing methods and the deliverables of an aerogeophysical survey in Olkiluoto area in May 2009. The survey was conducted by Geological Survey of Finland (GTK). The survey aircraft was a twin-engine Twin Otter operated by Finnish Aviation Academy (SIO) and owned by Natural Environment Research Council / British Geological Survey (NERC / BGS), with whom GTK has established a joint venture called Joint Airborne-geoscience Capability (JAC). The survey was conducted in May 2009 between May 5th and May 18th. The survey consists of ten separate survey flights and two magnetic calibration flights. The survey was based in Pori airport. Survey line spacing was 50 meters and nominal survey altitude was 30 meters. Measurements were completed in May 2009, and data processing and reporting was done in June 2009. Two cesium magnetometers installed onboard the aircraft (at the left wingtip and in a nose cone) were measuring the magnetic total field intensity during the survey flights. An automatic compensation unit corrected the aircraft attitude errors in the magnetic data in real time. The four-frequency electromagnetic (EM) unit included four transmitter coils with amplifiers in right wingtip and four receiver coils in left wingtip. Frequencies were 900 Hz, 3 kHz, 14 kHz and 24.5 kHz. The gamma spectrometer with two crystal packages (total volume 42 litres) measured the 256 channel energy spectra. In addition, auxiliary parameters such as flight altitude and aircraft attitude were also recorded simultaneously. Reference ground base station was used for recording the temporal variations in the magnetic field and also reference data for post-positioning of coordinate information. In the post-processing phase, heading correction, base station correction and microlevelling procedures were applied to the magnetic data. The EM data and radiometric data were corrected with calibration coefficients and levelled. The data was

Engineering Electromagnetics

International Nuclear Information System (INIS)

Kim, Se Yun

2009-01-01

This book deals with engineering electromagnetics. It contains seven chapters, which treats understanding of engineering electromagnetics such as magnet and electron spin, current and a magnetic field and an electromagnetic wave, Essential tool for engineering electromagnetics on rector and scalar, rectangular coordinate system and curl vector, electrostatic field with coulomb rule and method of electric images, Biot-Savart law, Ampere law and magnetic force, Maxwell equation and an electromagnetic wave and reflection and penetration of electromagnetic plane wave.

Airborne relay-based regional positioning system.

Science.gov (United States)

Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

2015-05-28

Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

A general framework of TOPSIS method for integration of airborne geophysics, satellite imagery, geochemical and geological data

Science.gov (United States)

Abedi, Maysam; Norouzi, Gholam-Hossain

2016-04-01

This work presents the promising application of three variants of TOPSIS method (namely the conventional, adjusted and modified versions) as a straightforward knowledge-driven technique in multi criteria decision making processes for data fusion of a broad exploratory geo-dataset in mineral potential/prospectivity mapping. The method is implemented to airborne geophysical data (e.g. potassium radiometry, aeromagnetic and frequency domain electromagnetic data), surface geological layers (fault and host rock zones), extracted alteration layers from remote sensing satellite imagery data, and five evidential attributes from stream sediment geochemical data. The central Iranian volcanic-sedimentary belt in Kerman province at the SE of Iran that is embedded in the Urumieh-Dokhtar Magmatic Assemblage arc (UDMA) is chosen to integrate broad evidential layers in the region of prospect. The studied area has high potential of ore mineral occurrences especially porphyry copper/molybdenum and the generated mineral potential maps aim to outline new prospect zones for further investigation in future. Two evidential layers of the downward continued aeromagnetic data and its analytic signal filter are prepared to be incorporated in fusion process as geophysical plausible footprints of the porphyry type mineralization. The low values of the apparent resistivity layer calculated from the airborne frequency domain electromagnetic data are also used as an electrical criterion in this investigation. Four remote sensing evidential layers of argillic, phyllic, propylitic and hydroxyl alterations were extracted from ASTER images in order to map the altered areas associated with porphyry type deposits, whilst the ETM+ satellite imagery data were used as well to map iron oxide layer. Since potassium alteration is generally the mainstay of porphyry ore mineralization, the airborne potassium radiometry data was used. The geochemical layers of Cu/B/Pb/Zn elements and the first component of PCA

Optical Airborne Tracker System

Data.gov (United States)

National Aeronautics and Space Administration — The Optical Airborne Tracker System (OATS) is an airborne dual-axis optical tracking system capable of pointing at any sky location or ground target.  The objectives...

A feasibility study of geogenic indoor radon mapping from airborne radiometric survey in northern Thailand

Energy Technology Data Exchange (ETDEWEB)

Wattananikorn, K. [Department of Physics, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)], E-mail: kittic@science.cmu.ac.th; Emharuthai, S. [Department of Physics, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wanaphongse, P. [Office of Atoms for Peace, Bangkok (Thailand)

2008-01-15

Experiments were carried out in seven test sites on three Quaternary alluvial and terrace deposit basins of northern Thailand, to test the possibility of using airborne equivalent uranium to predict geogenic indoor radon values of the region. The methodology was based on the correlation among soil gas permeability, soil radon concentration and indoor radon, as well as a relationship between soil radon and airborne uranium values. The methodology established works rather well when tested in areas of known indoor radon. Based on the predicted values that were obtained from this method, indoor radon in most areas of alluvial and terrace deposit basins of northern Thailand is less than 44Bq/m{sup 3}. There is no area in these basins where predicted indoor radon exceeds 74Bq/m{sup 3}.

Diurnal Variations of Airborne Pollen and Spores in Taipei City, Taiwan

Directory of Open Access Journals (Sweden)

Yueh-Lin Yang

2003-09-01

Full Text Available The diurnal variation of airborne pollen and spores in Taipei City, Taiwan, was investigated during a two-year survey from 1993 to 1994. The pollen and spores were sampled using a Burkard seven-day volumetric pollen trap. The diurnal trends of the total amount of pollen and spores in 1993 and in 1994 were similar to each other, and peaked at 3 to 10 o’clock. The diurnal patterns of airborne pollen and spores of Broussonetia, Fraxinus, Cyathea and Gramineae in 1993 were similar to those in 1994. High concentrations of Broussonetia and Fraxinus were obtained from midnight to the next morning. Cyathea spores peaked from morning till noon, and Gramineae peaked in the afternoon. The diurnal patterns of airborne pollen of Bischofia, Juniperus, Mallotus, Morus, Trema and Urticaceae in 1993 were different to those in 1994. Regular diurnal patterns also associated with the taxa, which produce large pollen or spores, such as Gramineae and Cyathea. In contrast, Bischofia, Juniperus, Mallotus, Morus, Trema and Urticaceae produce relatively small pollen and the diurnal patterns of their airborne pollen were found irregular. The source plants Broussonetia and Fraxinus were close to the collection site so the diurnal patterns of their airborne pollen were regular, suggesting that the diurnal fluctuations of the pollen or spores in air might be affected by the source of plants and the sizes of pollen or spores. The transportation of the smaller pollen or spores in air is probably more easily affected by instability of air currents; they are therefore more likely to exhibit irregular diurnal patterns.

Moving base Gravity Gradiometer Survey System (GGSS) program

Science.gov (United States)

Pfohl, Louis; Rusnak, Walter; Jircitano, Albert; Grierson, Andrew

1988-04-01

The GGSS program began in early 1983 with the objective of delivering a landmobile and airborne system capable of fast, accurate, and economical gravity gradient surveys of large areas anywhere in the world. The objective included the development and use of post-mission data reduction software to process the survey data into solutions for the gravity disturbance vector components (north, east and vertical). This document describes the GGSS equipment hardware and software, integration and lab test procedures and results, and airborne and land survey procedures and results. Included are discussions on test strategies, post-mission data reduction algorithms, and the data reduction processing experience. Perspectives and conclusions are drawn from the results.

A Study on Factors Affecting Airborne LiDAR Penetration

Directory of Open Access Journals (Sweden)

Wei-Chen Hsu

2015-01-01

Full Text Available This study uses data from different periods, areas and parameters of airborne LiDAR (light detection and ranging surveys to understand the factors that influence airborne LiDAR penetration rate. A discussion is presented on the relationships between these factors and LiDAR penetration rate. The results show that the flight height above ground level (AGL does not have any relationship with the penetration rate. There are some factors that should have larger influence. For example, the laser is affected by a wet ground surface by reducing the number of return echoes. The field of view (FOV has a slightly negative correlation with the penetration rate, which indicates that the laser incidence angle close to zero should achieve the best penetration. The vegetation cover rate also shows a negative correlation with the penetration rate, thus bare ground and reduced vegetation in the aftermath of a typhoon also cause high penetration rate. More return echoes could be extracted from the full-waveform system, thereby effectively improving the penetration rate. This study shows that full-waveform LiDAR is an effective method for increasing the number of surface reflected echoes. This study suggests avoiding LiDAR survey employment directly following precipitation to prevent laser echo reduction.

Airborne Tactical Crossload Planner

Science.gov (United States)

2017-12-01

Regiment AGL above ground level AO area of operation APA American psychological association ASOP airborne standard operating procedure A/C aircraft...awarded a research contract to develop a tactical crossload tool. [C]omputer assisted Airborne Planning Application ( APA ) that provides a

Evaluating airborne and ground based gamma spectrometry methods for detecting particulate radioactivity in the environment: a case study of Irish Sea beaches.

Science.gov (United States)

Cresswell, A J; Sanderson, D C W

2012-10-15

In several places, programmes are in place to locate and recover radioactive particles that have the potential to cause detrimental health effects in any member of the public who may encounter them. A model has been developed to evaluate the use of mobile gamma spectrometry systems within such programmes, with particular emphasis on large volume (16l) NaI(Tl) detectors mounted in low flying helicopters. This model uses a validated Monte Carlo code with assessment of local geochemistry and natural and anthropogenic background radiation concentrations and distributions. The results of the model, applied to the example of particles recovered from beaches in the vicinity of Sellafield, clearly show the ability of rapid airborne surveys conducted at 75 m ground clearance and 120 kph speeds to demonstrate the absence of sources greater than 5 MBq (137)Cs within large areas (10-20 km(2)h(-1)), and identify areas requiring further ground based investigation. Lowering ground clearance for airborne surveys to 15m whilst maintaining speeds covering 1-2 km(2) h(-1) can detect buried (137)Cs sources of 0.5MBq or greater activity. A survey design to detect 100 kBq (137)Cs sources at 10 cm depth has also been defined, requiring surveys at <15m ground clearance and <2 ms(-1) ground speed. The response of airborne systems to the Sellafield particles recovered to date has also been simulated, and the proportion of the existing radiocaesium background in the vicinity of the nuclear site has been established. Finally the rates of area coverage and sensitivities of both airborne and ground based approaches are compared, demonstrating the ability of airborne systems to increase the rate of particle recovery in a cost effective manner. The potential for equipment and methodological developments to improve performance are discussed. Copyright © 2012 Elsevier B.V. All rights reserved.

Gauge theory of weak, electromagnetic and dual electromagnetic interactions

International Nuclear Information System (INIS)

Soln, J.

1980-01-01

An SU 2 x U 1 algebra, in addition to the ordinary electric charge, also establishes the existence of the dual electric charge. This is taken as an indication of the existence of dual electromagnetic interactions in nature. Here, the unification of weak, electromagnetic and dual electromagnetic interactions is performed. The Yang-Mills-type group which contains the electromagnetic, dual electromagnetic and weak currents is SUsub(L,2) x U 1 x U' 1 . The masses of vector mesons are generated through the Higgs-Kibble mechanism. A simple consistency requirement suggests that dual electromagnetism and ordinary electromagnetism have the same strengths, leading the theory to a rather good agreement with experiments. (author)

Soil surveying using electromagnetic methods; Denji tansaho wo mochiita jiban chosa

Energy Technology Data Exchange (ETDEWEB)

Suzuki, I; Kawauchi, K; Goto, N [Muroran Institute of Technology, Hokkaido (Japan); Takahashi, N; Yamada, T [Zukohsya Co. Ltd., Hokkaido (Japan)

1997-10-22

Electromagnetic surveying method is applied in Muroran Institute of Technology`s site for power transmission steel towers for the locating of structures buried in the ground and for the study of obstruction to the application of the method. The devices employed are the EM31 and EM38 which are portable conductivity measuring instruments manufactured by GEONICS Company. With the probeable depth in the horizontal dipole mode being approximately half that in the vertical dipole mode, depths of 0.5m, 1m, 3m, and 6m may be explored using the two instruments. In the measurement test, the devices are used to determine a reinforced concrete-made multi-purpose duct that accommodates water pipes, sewers, various electric wires, and heating pipes and is buried at a depth of 2-3m in the ground. In the measurement for a 3m-deep level, a spot high in conductivity due to the reinforced concrete is detected, and the result roughly corresponds to the lay of the duct. In the measurement for a 6m-deep level, no high-conductivity spot is found, meaning there is no such structure at this depth. Although there are some other high conductivity values recorded, they are attributed to manhole covers or steel tower bases on the ground surface. 3 refs., 8 figs.

Development and study of airborne spectrometer system being compatible with nuclear emergency monitoring

International Nuclear Information System (INIS)

Jiangqi, Fang; Huaiwu, Wang; Mingkao, Hu; Renkang, Gu

2002-01-01

The exploitation and use of nuclear energy are of great importance to developing of national economy and maintaining state security. But it also has a possibility of serious accident. Based on the principles of airborne gamma ray spectrometry in the uranium exploration, nuclear emergency monitoring has been developed. This method has high sensitivity to the radioactive nuclides in the air and on the ground, and with the advantage of fast measuring in large area. Hence, in the middle of 1980s, some developed countries began to survey the scope and degree of nuclear accident contamination and environmental radiation level monitoring in the surrounding nuclear facilities, it can also be used to search for the lost radioactive sources. According to the actual situation and compatible guideline, National Nuclear Emergency Office consigned this project to our Center. After development and study on the Airborne gamma ray spectrometer system associated NaI(Tl) used for the uranium exploration, a compatible spectrometer system associated NaI(Tl) was established in a short period by us, which can fulfill airborne nuclear emergency survey basically. In normal situation, it was proved that the start-up time is less than two hours including transport to the airport. The system has high sensitivity to radioactive plume of 41 Ar and can respond rapidly to artificial sources, such as 192 Ir, 60 Co, 137 Cs and 131 I etc

On regulation of radioactive airborne discharge

International Nuclear Information System (INIS)

Stroganov, A.A.; Kuryndin, A.V.; Shapovalov, A.S.; Orlov, M.Yu.

2013-01-01

Authors present the Russian regulatory basis of radioactive airborne discharges which was updated after enactment of the Methodology for airborne discharge limits development. Criteria for establishing of airborne discharge limits, scope and other features of methodology are also considered in the article [ru

HIGH RESOLUTION AIRBORNE SHALLOW WATER MAPPING

Directory of Open Access Journals (Sweden)

F. Steinbacher

2012-07-01

Full Text Available In order to meet the requirements of the European Water Framework Directive (EU-WFD, authorities face the problem of repeatedly performing area-wide surveying of all kinds of inland waters. Especially for mid-sized or small rivers this is a considerable challenge imposing insurmountable logistical efforts and costs. It is therefore investigated if large-scale surveying of a river system on an operational basis is feasible by employing airborne hydrographic laser scanning. In cooperation with the Bavarian Water Authority (WWA Weilheim a pilot project was initiated by the Unit of Hydraulic Engineering at the University of Innsbruck and RIEGL Laser Measurement Systems exploiting the possibilities of a new LIDAR measurement system with high spatial resolution and high measurement rate to capture about 70 km of riverbed and foreland for the river Loisach in Bavaria/Germany and the estuary and parts of the shoreline (about 40km in length of lake Ammersee. The entire area surveyed was referenced to classic terrestrial cross-section surveys with the aim to derive products for the monitoring and managing needs of the inland water bodies forced by the EU-WFD. The survey was performed in July 2011 by helicopter and airplane and took 3 days in total. In addition, high resolution areal images were taken to provide an optical reference, offering a wide range of possibilities on further research, monitoring, and managing responsibilities. The operating altitude was about 500 m to maintain eye-safety, even for the aided eye, the airspeed was about 55 kts for the helicopter and 75 kts for the aircraft. The helicopter was used in the alpine regions while the fixed wing aircraft was used in the plains and the urban area, using appropriate scan rates to receive evenly distributed point clouds. The resulting point density ranged from 10 to 25 points per square meter. By carefully selecting days with optimum water quality, satisfactory penetration down to the river

High Resolution Airborne Shallow Water Mapping

Science.gov (United States)

Steinbacher, F.; Pfennigbauer, M.; Aufleger, M.; Ullrich, A.

2012-07-01

In order to meet the requirements of the European Water Framework Directive (EU-WFD), authorities face the problem of repeatedly performing area-wide surveying of all kinds of inland waters. Especially for mid-sized or small rivers this is a considerable challenge imposing insurmountable logistical efforts and costs. It is therefore investigated if large-scale surveying of a river system on an operational basis is feasible by employing airborne hydrographic laser scanning. In cooperation with the Bavarian Water Authority (WWA Weilheim) a pilot project was initiated by the Unit of Hydraulic Engineering at the University of Innsbruck and RIEGL Laser Measurement Systems exploiting the possibilities of a new LIDAR measurement system with high spatial resolution and high measurement rate to capture about 70 km of riverbed and foreland for the river Loisach in Bavaria/Germany and the estuary and parts of the shoreline (about 40km in length) of lake Ammersee. The entire area surveyed was referenced to classic terrestrial cross-section surveys with the aim to derive products for the monitoring and managing needs of the inland water bodies forced by the EU-WFD. The survey was performed in July 2011 by helicopter and airplane and took 3 days in total. In addition, high resolution areal images were taken to provide an optical reference, offering a wide range of possibilities on further research, monitoring, and managing responsibilities. The operating altitude was about 500 m to maintain eye-safety, even for the aided eye, the airspeed was about 55 kts for the helicopter and 75 kts for the aircraft. The helicopter was used in the alpine regions while the fixed wing aircraft was used in the plains and the urban area, using appropriate scan rates to receive evenly distributed point clouds. The resulting point density ranged from 10 to 25 points per square meter. By carefully selecting days with optimum water quality, satisfactory penetration down to the river bed was achieved

Electromagnetic fields - introduction to relevant issues

International Nuclear Information System (INIS)

Brueggemeyer, H.; Csicsaky, M.

1993-01-01

This introductory paper surveys potential sources of electric magnetic, and electro-magnetic fields. Various cases are discussed to exemplify the total frequency range: nuclear magnetic resonance tomography, high-voltage transmission lines, transformer stations, effect lighting balls, military transmitters, transmitter towers of the Postal Services and other operators, mobile radiotelephone equipment, large broadcasting transmitters, radar radiation, high-frequency heat therapy. There is evidence suggesting that electric, magnetic and electro-magnetic fields may possibly represent a certain nuisance or health hazard even at field strength occuring in equipment used for every-day-life purposes, with an emphasis on their possible actions and effects in children and adolescents. The author discusses, in conclusion, the aerial equipment ordinance issued by Lower Saxony. (Uhe) [de

Mapping methane emissions using the airborne imaging spectrometer AVIRIS-NG

Science.gov (United States)

Thorpe, A. K.; Frankenberg, C.; Thompson, D. R.; Duren, R. M.; Bue, B. D.; Green, R. O.

2017-12-01

The next generation Airborne Visible/Infrared Imaging Spectrometer (AVIRIS-NG) has been used to survey large regions and map methane plumes with unambiguous identification of emission source locations. This capability is aided by real time detection and geolocation of gas plumes, permitting adaptive surveys and communication to ground teams for rapid follow up. We present results from AVIRIS-NG flight campaigns in Colorado, New Mexico, and California. Hundreds of plumes were observed, reflecting emissions from the energy sector that include hydraulic fracturing, gas processing plants, tanks, pumpjacks, and pipeline leaks. In some cases, plumes observed by AVIRIS-NG resulted in mitigation. Additional examples will be shown for methane from dairy lagoons, landfills, natural emissions, as well as carbon dioxide from power plants and refineries. We describe the unique capabilities of airborne imaging spectrometers to augment other measurement techniques by efficiently surveying key regions for methane point sources and supporting timely assessment and mitigation. We summarize the outlook for near- and longer-term monitoring capabilities including future satellite systems. Figure caption. AVIRIS-NG true color image subset with superimposed methane plume showing retrieved gas concentrations. Plume extends 200 m downwind of the southern edge of the well pad. Google Earth imagery with finer spatial resolution is also included (red box), indicating that tanks in the inset scene as the source of emissions. Five wells are located at the center of this well pad and all use horizontal drilling to produce mostly natural gas.

Electromagnetic Waves

DEFF Research Database (Denmark)

This book is dedicated to various aspects of electromagnetic wave theory and its applications in science and technology. The covered topics include the fundamental physics of electromagnetic waves, theory of electromagnetic wave propagation and scattering, methods of computational analysis......, material characterization, electromagnetic properties of plasma, analysis and applications of periodic structures and waveguide components, etc....

Self-reported symptoms associated with exposure to electromagnetic fields: a questionnaire study.

Science.gov (United States)

Küçer, Nermin; Pamukçu, Tuğba

2014-01-01

Abstract In the last years, it has been discussed frequently whether there are any harmful effects of electromagnetic fields on human health. Electromagnetic fields are generated by several natural and man-made sources. Part of the electromagnetic spectrum called Radiofrequency is used in communication systems such as mobile (cellular) phone and computer. The aim of our study was to explore different self-reported symptoms that may be associated with exposure to electromagnetic fields. This survey study was conducted, using a questionnaire, on 350 people aged +9 years in Turkey. The chi-square test was used for data analysis. Self-reported symptoms were headache, vertigo/dizziness, fatigue, forgetfulness, sleep disturbance-insomnia, tension-anxiety, joint and bone pain, lacrimation of the eyes, hearing loss and tinnitus. As a result of the survey, the study has shown that users of mobile phone and computer more often complained of headache, joint and bone pain, hearing loss, vertigo/dizziness, tension-anxiety symptoms according to time of daily usage (p < 0.05). In users of mobile phone and computer, women significantly (p < 0.05) complained more often of headache, vertigo/dizziness, fatigue, forgetfulness and tension-anxiety than men.

Routing architecture and security for airborne networks

Science.gov (United States)

Deng, Hongmei; Xie, Peng; Li, Jason; Xu, Roger; Levy, Renato

2009-05-01

Airborne networks are envisioned to provide interconnectivity for terrestial and space networks by interconnecting highly mobile airborne platforms. A number of military applications are expected to be used by the operator, and all these applications require proper routing security support to establish correct route between communicating platforms in a timely manner. As airborne networks somewhat different from traditional wired and wireless networks (e.g., Internet, LAN, WLAN, MANET, etc), security aspects valid in these networks are not fully applicable to airborne networks. Designing an efficient security scheme to protect airborne networks is confronted with new requirements. In this paper, we first identify a candidate routing architecture, which works as an underlying structure for our proposed security scheme. And then we investigate the vulnerabilities and attack models against routing protocols in airborne networks. Based on these studies, we propose an integrated security solution to address routing security issues in airborne networks.

Environmental surveys

International Nuclear Information System (INIS)

Costa-Ribeiro, C.

1977-01-01

An environmental survey conducted in high natural radioactivity areas and methods used to evaluated radiation doses received by the population are presented. It is shown doses absorved due to ingestion of radioactively contaminated food and water. Exposure to external gamma radiation fields or inhalation of abnormal quantities of natural airborne radioactivity are discussed [pt

Optical Backscattering Measured by Airborne Lidar and Underwater Glider

Directory of Open Access Journals (Sweden)

James H. Churnside

2017-04-01

Full Text Available The optical backscattering from particles in the ocean is an important quantity that has been measured by remote sensing techniques and in situ instruments. In this paper, we compare estimates of this quantity from airborne lidar with those from an in situ instrument on an underwater glider. Both of these technologies allow much denser sampling of backscatter profiles than traditional ship surveys. We found a moderate correlation (R = 0.28, p < 10−5, with differences that are partially explained by spatial and temporal sampling mismatches, variability in particle composition, and lidar retrieval errors. The data suggest that there are two different regimes with different scattering properties. For backscattering coefficients below about 0.001 m−1, the lidar values were generally greater than the glider values. For larger values, the lidar was generally lower than the glider. Overall, the results are promising and suggest that airborne lidar and gliders provide comparable and complementary information on optical particulate backscattering.

Using airborne GAMMA-ray spectrometry (uranium, thorium, potassium) to quantify weathering and erosion processes

International Nuclear Information System (INIS)

Carrier, F.

2005-01-01

The airborne gamma-ray spectrometry survey carried out on the Armorican Massif provided soil contents in U, Th and K in ppm. Chemical and mechanical erosion processes within a homogeneous geological unit have been estimated using their variations and those of the 137 Cs. Our new approach, based on a multivariate analysis (hierarchic ascending classification), integrates the airborne gamma-ray spectrometry data, with their broad spatial distribution, together with precisely located station data (major elements, traces and isotopic geochemistry) resulting from a soil and river water erosion products survey. The total export of potassium was estimated in any point of an area catchment (50-m resolution) until 17+2 t/km 2 /a for a 50-m thick weathering profile. Erosion study by river sampling provide important biases, for the perennial river does not integrate the whole range of erosion products: the geochemical signature of the valleys is currently more represented than plateau areas. (author)

Environmental exposures to electromagnetic fields and health. Opinion note of the Institut de Veille Sanitaire

International Nuclear Information System (INIS)

2014-01-01

This note states the opinion the French Institute for Health Survey (Institut de Veille Sanitaire, InVS) on the effect of electromagnetic fields (used in mobile phones, television and radio broadcasting, radar and satellite communication, or microwave ovens) on health. While distinguishing extremely low frequency and radio-frequency electromagnetic fields, it proposes an overview of acquired knowledge and commonly acknowledged elements on risks for health. It discusses what is supposed or claimed for these both types of fields in terms of carcinogenic and non carcinogenic effects, and also in the particular case of idiopathic environmental intolerance to electromagnetic fields. A third part presents actions undertaken by the InVS (epidemiological survey and field studies), actions to be pursued or supported

Electromagnetic transients as triggers in searches for gravitational waves from compact binary mergers

Science.gov (United States)

Kelley, Luke Zoltan; Mandel, Ilya; Ramirez-Ruiz, Enrico

2013-06-01

The detection of an electromagnetic transient which may originate from a binary neutron star merger can increase the probability that a given segment of data from the LIGO-Virgo ground-based gravitational-wave detector network contains a signal from a binary coalescence. Additional information contained in the electromagnetic signal, such as the sky location or distance to the source, can help rule out false alarms and thus lower the necessary threshold for a detection. Here, we develop a framework for determining how much sensitivity is added to a gravitational-wave search by triggering on an electromagnetic transient. We apply this framework to a variety of relevant electromagnetic transients, from short gamma-ray bursts (GRBs) to signatures of r-process heating to optical and radio orphan afterglows. We compute the expected rates of multimessenger observations in the advanced detector era and find that searches triggered on short GRBs—with current high-energy instruments, such as Fermi—and nucleosynthetic “kilonovae”—with future optical surveys, like the Large Synoptic Survey Telescope—can boost the number of multimessenger detections by 15% and 40%, respectively, for a binary neutron star progenitor model. Short GRB triggers offer precise merger timing but suffer from detection rates decreased by beaming and the high a priori probability that the source is outside the LIGO-Virgo sensitive volume. Isotropic kilonovae, on the other hand, could be commonly observed within the LIGO-Virgo sensitive volume with an instrument roughly an order of magnitude more sensitive than current optical surveys. We propose that the most productive strategy for making multimessenger gravitational-wave observations is using triggers from future deep, optical all-sky surveys, with characteristics comparable to the Large Synoptic Survey Telescope, which could make as many as ten such coincident observations a year.

LAN MAP: An Innovative Airborne Light at Night Mapping Project

Science.gov (United States)

Craine, Eric R.; Craine, B. L.; Craine, E. M.; Craine, P. R.

2013-01-01

Widespread installation of inefficient and misdirected artificial light at night (LAN) has led to increasing concerns about light pollution and its impact, not only on astronomical facilities but larger communities as well. Light pollution impacts scientific research, environmental ecosystems, human health, and quality of life. In recent years, the public policy response to light pollution has included formulation of government codes to regulate lighting design and installation. Various environmental groups now include light pollution among their rallying themes to protest both specific and general developments. The latter efforts are often conducted in the absence of any quantitative data and are frequently charged by emotion rather than reason. To bring some scientific objectivity, and quantitative data, to these discussions, we have developed a suite of tools for simultaneous photometric measurements and temporal monitoring of both local communities and the sky overhead. We have also developed novel protocols for the use of these tools, including a triad of airborne, ground mobile, and ground static photometric surveys. We present a summary of these tools and protocols, with special emphasis on the airborne systems, and discuss baseline and follow-up measurements of LAN environments in the vicinity of numerous observatories in Arizona, the home of the initial LAN MAP surveys.

Mineral exploration trends and developments in 1981

International Nuclear Information System (INIS)

Hood, P.J.

1982-01-01

Mineral exploration activity worldwide in 1981 appeared to be at a slighly higher level than in previous years in spite of the continued generally depressed base metal prices. Uranium exploration activity has fallen in the past four years from a peak in 1976-77. In airborne geophysical surveying, the aeromagnetic and combined airborne electromagnetic/ magnetic techniques continued to be employed particularly in Africa. In-field data processing resulting from the incorporation of microprocessors into ground equipment has continued to increase, and computer systems for base camp use are being introduced

Airborne Cloud Computing Environment (ACCE)

Science.gov (United States)

Hardman, Sean; Freeborn, Dana; Crichton, Dan; Law, Emily; Kay-Im, Liz

2011-01-01

Airborne Cloud Computing Environment (ACCE) is JPL's internal investment to improve the return on airborne missions. Improve development performance of the data system. Improve return on the captured science data. The investment is to develop a common science data system capability for airborne instruments that encompasses the end-to-end lifecycle covering planning, provisioning of data system capabilities, and support for scientific analysis in order to improve the quality, cost effectiveness, and capabilities to enable new scientific discovery and research in earth observation.

Application of frequency- and time-domain electromagnetic surveys to characterize hydrostratigraphy and landfill construction at the Amargosa Desert Research Site, Beatty, Nevada

Science.gov (United States)

White, Eric A.; Day-Lewis, Frederick D.; Johnson, Carole D.; Lane, John W.

2016-01-01

In 2014 and 2015, the U.S. Geological Survey (USGS), conducted frequency-domain electromagnetic (FDEM) surveys at the USGS Amargosa Desert Research Site (ADRS), approximately 17 kilometers (km) south of Beatty, Nevada. The FDEM surveys were conducted within and adjacent to a closed low-level radioactive waste disposal site located at the ADRS. FDEM surveys were conducted on a grid of north-south and east-west profiles to assess the locations and boundaries of historically recorded waste-disposal trenches. In 2015, the USGS conducted time-domain (TDEM) soundings along a profile adjacent to the disposal site (landfill) in cooperation with the U.S. Environmental Protection Agency (USEPA), to assess the thickness and characteristics of the underlying deep unsaturated zone, and the hydrostratigraphy of the underlying saturated zone.FDEM survey results indicate the general location and extent of the waste-disposal trenches and reveal potential differences in material properties and the type and concentration of waste in several areas of the landfill. The TDEM surveys provide information on the underlying hydrostratigraphy and characteristics of the unsaturated zone that inform the site conceptual model and support an improved understanding of the hydrostratigraphic framework. Additional work is needed to interpret the TDEM results in the context of the local and regional structural geology.

Aerial radiation survey

International Nuclear Information System (INIS)

Pradeep Kumar, K.S.

1998-01-01

Aerial gamma spectrometry surveys are the most effective, comprehensive and preferred tool to delimit the large area surface contamination in a radiological emergency either due to a nuclear accident or following a nuclear strike. The airborne survey apart from providing rapid and economical evaluation of ground contamination over large areas due to larger ground clearance and higher speed, is the only technique to overcome difficulties posed by ground surveys of inaccessible region. The aerial survey technique can also be used for searching of lost radioactive sources, tracking of radioactive plume and generation of background data on the Emergency Planning Zone (EPZ) of nuclear installations

Problems in classical electromagnetism 157 exercises with solutions

CERN Document Server

Macchi, Andrea; Pegoraro, Francesco

2017-01-01

This book contains 157 problems in classical electromagnetism, most of them new and original compared to those found in other textbooks. Each problem is presented with a title in order to highlight its inspiration in different areas of physics or technology, so that the book is also a survey of historical discoveries and applications of classical electromagnetism. The solutions are complete and include detailed discussions, which take into account typical questions and mistakes by the students. Without unnecessary mathematical complexity, the problems and related discussions introduce the student to advanced concepts such as unipolar and homopolar motors, magnetic monopoles, radiation pressure, angular momentum of light, bulk and surface plasmons, radiation friction, as well as to tricky concepts and ostensible ambiguities or paradoxes related to the classical theory of the electromagnetic field. With this approach the book is both a teaching tool for undergraduates in physics, mathematics and electric engine...

Airborne gamma-ray spectrometry and computer data processing

International Nuclear Information System (INIS)

Raghuwanshi, S.S.; Bhishma Kumar; Tewari, S.G.

1993-01-01

The physical basis for the measurement of radioelemental concentrations of U, Th, and K on the surface of the earth by airborne gamma-ray spectrometry (AGRS) are described in this paper. The yield of an infinite radioactive plane source for a particular gamma energy helps to know the sampled volume in AGRS, the ground coverage, the ground resolution, the effective planning of the survey, flight line spacing, and sampling time. The infinite source-yield enables the determination of the attenuation coefficients in actual surveys and lays down the criteria for a standard test strip. Scattering of gamma-rays in matter is discussed in order to study its influence in the measurements from air. The theoretical gamma-ray spectrum from terrestrial U, Th, and K are discussed in contrast to its realistic picture which poses problems for their direct use for measurements. The criterion of FWHM (full width at half maximum) and inter-energy distance with their yields is described which finally helps to select the energy windows for (window and MCA) AGRS system. Factors which affect the measurements of radioelemental concentration in AGRS surveys include both correctable and non-correctable ones. Correctable factors are : (a) non-terrestrial sources of gamma-rays aircraft, cosmic, and airborne background (H) (B); (b) interference due to gamma-scattering inter channel effects (l); (c) height variations (H) due to navigation and topography; (d) temperature (T) of ambient air; and (e) pressure (P) of air at flying altitude. For removal of background effects, measurements over test strip and calibration pads are necessary for making the corrections in the order - BIH. These methods are described in the paper. The non-correctable factors include effects, due to terrain moisture, vegetation, and others. The possible ways to eliminate these effects are also briefly described. (author). 17 refs., 13 figs

Geophysical investigations in the Veitsivaara area, Finland summary report

International Nuclear Information System (INIS)

Heikkinen, E.; Saksa, P.; Hinkkanen, H.

1991-10-01

Teollisuuden Voima Oy (TVO carries out site investigations in Finland for final disposal of nuclear high level waste during 1987-2000. Investigations by geological, geophysical, geohydrological and geochemical methods were carried out in the Veitsivaara area in 1987-90 to determine the suitability of the bedrock for the final disposal of spent nuclear fuel. Airborne, ground and borehole geophysical methods were used to study the rock type distribution, fracturing and hydraulic conductivity. Airborne surveys were performed by magnetic, radiometric and two electromagnetic methods and ground investigations by VLF magnetic and resistivity, magnetic and impulse radar methods. Electromagnetic and seismic refraction surveys were used to locate crushed and fracture zones. The properties of weak electrical conductors, e.g. their depth dimensions, were studied by direct current resistivity measurements. The rock type distribution was studied by single-hole logging of susceptibility, natural γ-radiation and radiometric γ γ-density. Electrical and acoustic logging allowed water bearing fractures to be mapped and the results of water injection tests to be interpreted. Flow conditions in the boreholes were studied by both fluid logging and tube wave sounding

Monitoring of Electromagnetic Radiation from Cellular Base Stations in Kuwait

International Nuclear Information System (INIS)

Al-Otaibi, A.H.; Al-Ajmi, D.; Williams, T.; McGee, D.; Dennis, J.A.; Beg, M.U.

1998-01-01

A survey of the radio frequency electromagnetic environment in Kuwait was carried out. The primary purpose of this survey was to monitor electromagnetic radiation (EMR) field strength levels emitted by cellular base stations installed and operated by the Kuwait Mobile Telecommunications Company (MTC). Measurements were made at 26 cellular-phone base stations, chosen as a representative sample to include 14 school sites, 2 residential sites, 2 hospital sites, 3 ministerial building sites, 3 commercial sites and 1 typical stand-alone site. On all the selected sites measurements were made with a spectrum analyser to determine the emission level in the frequency bands used by the base station transmitters (917-960 MHz). The results indicated that total field strength, specifically due to the MTC base stations, found in public access areas, varied generally between 0.05 and 1.13 V.m -1 . These values are in the order of between 40 and 800 times lower than the new pan-European CENELEC pre-standard ENV 50166-2 'Human Exposure to Electromagnetic Fields'. In terms of power density the highest observed value (0.34 μW.m -2 ) was more than a thousand times below the prescribed standards. (author)

Mapping of radiation anomalies using UAV mini-airborne gamma-ray spectrometry.

Science.gov (United States)

Šálek, Ondřej; Matolín, Milan; Gryc, Lubomír

2018-02-01

Localization of size-limited gamma-ray anomalies plays a fundamental role in uranium prospecting and environmental studies. Possibilities of a newly developed mini-airborne gamma-ray spectrometric equipment were tested on a uranium anomaly near the village of Třebsko, Czech Republic. The measurement equipment was based on a scintillation gamma-ray spectrometer specially developed for unmanned aerial vehicles (UAV) mounted on powerful hexacopter. The gamma-ray spectrometer has two 103 cm 3 BGO scintillation detectors of relatively high sensitivity. The tested anomaly, which is 80 m by 40 m in size, was investigated by ground gamma-ray spectrometric measurement in a detail rectangular measurement grid. Average uranium concentration is 25 mg/kg eU attaining 700 mg/kg eU locally. The mini-airborne measurement across the anomaly was carried out on three 100 m long parallel profiles at eight flight altitudes from 5 to 40 m above the ground. The resulting 1 s 1024 channel gamma-ray spectra, recorded in counts per second (cps), were processed to concentration units of K, U and Th, while total count (TC) was reported in cps. Increased gamma ray intensity of the anomaly was indicated by mini-airborne measurement at all profiles and altitudes, including the highest altitude of 40 m, at which the recorded intensity is close to the natural radiation background. The reported instrument is able to record data with comparable quality as standard airborne survey, due to relative sensitive detector, lower flight altitude and relatively low flight speed of 1 m/s. The presented experiment brings new experience with using unmanned semi-autonomous aerial vehicles and the latest mini-airborne radiometric instrument. The experiment has demonstrated the instrument's ability to localize size-limited uranium anomalies. Copyright © 2017 Elsevier Ltd. All rights reserved.

A survey of natural terrestrial and airborne radionuclides in moss samples from the peninsular Thailand.

Science.gov (United States)

Wattanavatee, Komrit; Krmar, Miodrag; Bhongsuwan, Tripob

2017-10-01

The aim of this study was to determine the activity concentrations of natural terrestrial radionuclides ( 238 U, 226 Ra, 232 Th and 40 K) and airborne radionuclides ( 210 Pb, 210 Pb ex and 7 Be) in natural terrestrial mosses. The collected moss samples (46) representing 17 species were collected from 17 sampling localities in the National Parks and Wildlife Sanctuaries of Thailand, situated in the mountainous areas between the northern and the southern ends of peninsular Thailand (∼7-12 °N, 99-102 °E). Activity concentrations of radionuclides in the samples were measured using a low background gamma spectrometer. The results revealed non-uniform spatial distributions of all the radionuclides in the study area. Principal component analysis and cluster analysis revealed two distinct origins for the studied radionuclides, and furthermore, the Pearson correlations were strong within 226 Ra, 232 Th, 238 U and 40 K as well as within 210 Pb and 210 Pb ex , but there was no significant correlation between these two groups. Also 7 Be was uncorrelated to the others, as expected due to different origins of the airborne and terrestrial radionuclides. The radionuclide activities of moss samples varied by moss species, topography, geology, and meteorology of each sampling area. The observed abnormally high concentrations of some radionuclides probably indicate that the concentrations of airborne and terrestrial radionuclides in moss samples were directly related to local geological features of the sampling site, or that high levels of 7 Be were most probably linked with topography and regional NE monsoonal winds from mainland China. Copyright © 2017 Elsevier Ltd. All rights reserved.

TNB high tension overhead cables: is their electromagnetic field hazard real?

International Nuclear Information System (INIS)

Roha Tukimin; Mohd Yusof Mohd Ali; Mohamad Amirul Nizam

2005-01-01

Extremely low frequency electromagnetic fields (ELF, EMF) fall under the category of non-ionising radiation. We live in an electromagnetic environment generated by both natural (earths magnetic field, sunlight) and man-made. One of the man-made sources which produces significant electromagnetic fields (EMF) is the electric power supply system. In modern time, electricity has become an essential part of our lives. Electric power supply system, which includes generation, transmission and distribution of the electricity, produces extremely low frequency electromagnetic fields (ELF EMF) that travel along the overhead cables at 50 cycles per second (50 Hz).They are a form of energy that travels in space as electromagnetic waves. In spite of the fact that ELF EMF are very weak electromagnetic emission, they are believed to be hazardous to human health because of their ability to induce current and to initiate energy deposition in the body, which may eventually lead to increase in body temperature, behavioral changes and perhaps cancer in the long term. Due to their potential of causing such health hazard, several companies have approached and requested MINT to carry out surveys and safety assessments of their land properties, which are located close to the transmission lines. This paper highlights some of the works that had been carried out by MINT based on the requests received. They were performed based on international standard IEEE procedures protocols using properly calibrated portable ELF instruments. The results confirmed that ELF EMF did present at the survey sites but were very much lower than the permissible exposure limit recommended for members of public (1000 m Gauss / 5000 V/m). They were found to vary against measurements locations, which were strongly influenced by vertical and horizontal distances from the cables and by the presence of other objects like building and trees. (Author)

Contribution of a combined TDEM (Time-Domain electromagnetism) and geoelectrical survey to the investigation of the coastal aquifer of Puerto Morelos, Quintana Roo, Mexico

Science.gov (United States)

Rebolledo-Vieyra, M.; Ravelo-Cervantes, J. I.; Lecossec, A.

2007-12-01

This study reports initial results of combined Time Domain Electromagnetic (TDEM) and vertical electrical sounding (VES), geophysical characterization of the Quintana Roo coastal aquifer, with the aim of establishing effective protocols for subsequent surveys in the area, through the association of TDEM and VES. The high resistivity of the carbonate terrain, combined with the very low resistivity range of fresh-water and sea-water, are ideal to use both tools in combination. The results show that both methods used in a combination may provide a useful tool for hydrogeologial studies. In this survey we were able to identifiy a fracture 100 m x 40 m, that was correlated to fresh-water discharges in to the Puerto Morelos Reef lagoon.

Redatuming controlled-source electromagnetic data using Stratton–Chu type integral transformations

DEFF Research Database (Denmark)

Zhdanov, Michael; Cai, Hongzhu

2016-01-01

We present a new method of analyzing controlled-source electromagnetic (CSEM) data based on redatuming of the observed data from the actual receivers into the virtual receivers. We use the Stratton–Chu type integral transform to calculate the EM field in the virtual receivers. The virtual receivers...... can be placed at any desirable position, including close to the target, which increases the sensitivity of the EM data to the target. The developed method provides an effective model-based interpolation/extrapolation tool for electromagnetic field data. This paper demonstrates that redatuming can...... be used for designing the optimized CSEM survey configuration. The numerical examples, for the Kevin Dome Electromagnetic Project Site, illustrate the practical effectiveness of the developed method....

Monitoring and evaluation techniques for airborne contamination

Energy Technology Data Exchange (ETDEWEB)

Yihua, Xia [China Inst. of Atomic Energy, Beijing (China)

1997-06-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Monitoring and evaluation techniques for airborne contamination

International Nuclear Information System (INIS)

Xia Yihua

1997-01-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Surveying and assessing the hazards associated with the processing of uranium

International Nuclear Information System (INIS)

Kruger, J.

1980-01-01

The control of uranium during the milling process has not received extensive attention. The results of several surveys of surface contamination, airborne contamination and external radiation made at South African processing facilities are presented and compared with derived norms for permissible exposure to uranium dust. The routine urine sampling results are used as an indicator of personnel exposures. Results of sampling identify the main sources of airborne activity and indicate the contribution of general surface contamination levels to airborne levels. The use of surface contamination levels together with frequent air sampling for assessing the environmental conditions is illustrated. It is concluded that infrequent grab air sampling alone is not adequate for assessing the hazards during uranium processing. Detailed surveys are required and proper area and personnel access control are indicated. (H.K.)

Calculation of electromagnetic force in electromagnetic forming process of metal sheet

International Nuclear Information System (INIS)

Xu Da; Liu Xuesong; Fang Kun; Fang Hongyuan

2010-01-01

Electromagnetic forming (EMF) is a forming process that relies on the inductive electromagnetic force to deform metallic workpiece at high speed. Calculation of the electromagnetic force is essential to understand the EMF process. However, accurate calculation requires complex numerical solution, in which the coupling between the electromagnetic process and the deformation of workpiece needs be considered. In this paper, an appropriate formula has been developed to calculate the electromagnetic force in metal work-piece in the sheet EMF process. The effects of the geometric size of coil, the material properties, and the parameters of discharge circuit on electromagnetic force are taken into consideration. Through the formula, the electromagnetic force at different time and in different positions of the workpiece can be predicted. The calculated electromagnetic force and magnetic field are in good agreement with the numerical and experimental results. The accurate prediction of the electromagnetic force provides an insight into the physical process of the EMF and a powerful tool to design optimum EMF systems.

Electromagnetically shielded building

Energy Technology Data Exchange (ETDEWEB)

Takahashi, T; Nakamura, M; Yabana, Y; Ishikawa, T; Nagata, K

1992-04-21

This invention relates to a building having an electromagnetic shield structure well-suited for application to an information network system utilizing electromagnetic waves, and more particularly to an electromagnetically shielded building for enhancing the electromagnetic shielding performance of an external wall. 6 figs.

Electromagnetically shielded building

International Nuclear Information System (INIS)

Takahashi, T.; Nakamura, M.; Yabana, Y.; Ishikawa, T.; Nagata, K.

1992-01-01

This invention relates to a building having an electromagnetic shield structure well-suited for application to an information network system utilizing electromagnetic waves, and more particularly to an electromagnetically shielded building for enhancing the electromagnetic shielding performance of an external wall. 6 figs

Active airborne contamination control using electrophoresis

International Nuclear Information System (INIS)

Veatch, B.D.

1994-01-01

In spite of our best efforts, radioactive airborne contamination continues to be a formidable problem at many of the Department of Energy (DOE) weapons complex sites. For workers that must enter areas with high levels of airborne contamination, personnel protective equipment (PPE) can become highly restrictive, greatly diminishing productivity. Rather than require even more restrictive PPE for personnel in some situations, the Rocky Flats Plant (RFP) is actively researching and developing methods to aggressively combat airborne contamination hazards using electrophoretic technology. With appropriate equipment, airborne particulates can be effectively removed and collected for disposal in one simple process. The equipment needed to implement electrophoresis is relatively inexpensive, highly reliable, and very compact. Once airborne contamination levels are reduced, less PPE is required and a significant cost savings may be realized through decreased waste and maximized productivity. Preliminary ''cold,'' or non-radioactive, testing results at the RFP have shown the technology to be effective on a reasonable scale, with several potential benefits and an abundance of applications

ZPR-9 airborne plutonium monitoring system

International Nuclear Information System (INIS)

Rusch, G.K.; McDowell, W.P.; Knapp, W.G.

1975-01-01

An airborne plutonium monitoring system which is installed in the ZPR-9 (Zero Power Reactor No. 9) facility at Argonne National Laboratory is described. The design and operational experience are discussed. This monitoring system utilizes particle size and density discrimination, alpha particle energy discrimination, and a background-subtraction techique operating in cascade to separate airborne-plutonium activity from other, naturally occurring, airborne activity. Relatively high sensitivity and reliability are achieved

Software for airborne radiation monitoring system

International Nuclear Information System (INIS)

Sheinfeld, M.; Kadmon, Y.; Tirosh, D.; Elhanany, I.; Gabovitch, A.; Barak, D.

1997-01-01

The Airborne Radiation Monitoring System monitors radioactive contamination in the air or on the ground. The contamination source can be a radioactive plume or an area contaminated with radionuclides. This system is composed of two major parts: Airborne Unit carried by a helicopter, and Ground Station carried by a truck. The Airborne software is intended to be the core of a computerized airborne station. The software is written in C++ under MS-Windows with object-oriented methodology. It has been designed to be user-friendly: function keys and other accelerators are used for vital operations, a help file and help subjects are available, the Human-Machine-Interface is plain and obvious. (authors)

Electromagnetic interactions

International Nuclear Information System (INIS)

Bosanac, Slobodan Danko

2016-01-01

This book is devoted to theoretical methods used in the extreme circumstances of very strong electromagnetic fields. The development of high power lasers, ultrafast processes, manipulation of electromagnetic fields and the use of very fast charged particles interacting with other charges requires an adequate theoretical description. Because of the very strong electromagnetic field, traditional theoretical approaches, which have primarily a perturbative character, have to be replaced by descriptions going beyond them. In the book an extension of the semi-classical radiation theory and classical dynamics for particles is performed to analyze single charged atoms and dipoles submitted to electromagnetic pulses. Special attention is given to the important problem of field reaction and controlling dynamics of charges by an electromagnetic field.

Electromagnetic fields of Nanometer electromagnetic waves and X-ray. New frontiers of electromagnetic wave engineering

International Nuclear Information System (INIS)

2009-01-01

The investigating committee aimed at research on electromagnetic fields in functional devices and X-ray fibers for efficient coherent X-ray generation and their material science, high-precision manufacturing, X-ray microscope, application to medical and information communication technologies, such as interaction between material and nanometer electromagnetic waves of radiated light and X-ray, interaction between microwaves and particle beams, theory and design of high-frequency waveguides for resonator and accelerator, from January 2003 to December 2005. In this report, we describe our research results, in particular, on the topics of synchrotron radiation and Cherenkov radiation, Kyushu synchrotron light source and its technology, nanometer electromagnetic fields in optical region, process of interaction between evanescent waves and near-field light, orthogonal relation of electromagnetic fields including evanescent waves in dispersive dielectrics, optical amplification using electron beam, nanometer electromagnetic fields in focusing waveguide lens device with curved facets, electromagnetic fields in nanometer photonic crystal waveguide consisting of atoms, X-ray scattering and absorption I bio-material for image diagnosis. (author)

Using NASA`s Airborne Topographic Mapper IV to Quantify Geomorphic Change in Arid Southwestern Stream Systems

Science.gov (United States)

Finnegan, D. C.; Krabill, W.; Lichvar, R. W.; Ericsson, M. P.; Frederick, E.; Manizade, S.; Yungel, J.; Sonntag, J.; Swift, R.

2005-12-01

Understanding how arid stream systems respond to individual climatic events is often difficult given the dynamic and `flashy' nature of most watersheds and the unpredictable nature of individual storm events. Until recently conventional methods for quantifying change dictated the use of stream gauge measurements coupled with periodic cross-section measurements to quantify changes in large-scale channel geometry. Using this approach to quantify change across large areas often proves to be impractical and unattainable given the laborious nature of most surveying techniques including modern GPS systems. Alternately, airborne laser technologies such as NASA's Airborne Topographic Mapper (ATM) are capable of quantifying small-scale changes (~5-10cm) across large-scale terrain rapidly and accurately. The ATM was developed at the NASA-GSFC Wallops Flight Facility. Its current version, ATM-4, measures topography 5,000 times per second across a 45-degree swath below the aircraft by transmitting a 532nm (green) laser pulse and receiving the backscattered signal in a high-speed waveform digitizer. The laser range measurements are combined with aircraft location from GPS and attitude from an inertial navigation system (INS) to provide a precise XYZ coordinate for each (~1-meter diameter) laser footprint on the ground. Our work focuses on the use of airborne laser altimetry to quantify the nature of individual surfaces and the geomorphic change that occurs within small arid stream systems during significant storm events. In September of 2003 and 2005 acquisition surveys using NASA's ATM-IV were flown over Mission Creek, a small arid stream system in Southern California's Mojave Desert with a relatively long gauging history (>40yrs), allowing us to quantify the geomorphic change occurring within the channel as a result of the record storm events during the winter of 2004-2005. Preliminary results associated with our work are encouraging and lead us to believe that when compared

Airborne remote sensing of estuarine intertidal radionuclide concentrations

International Nuclear Information System (INIS)

Rainey, M.P.

1999-08-01

The ability to map industrial discharges through remote sensing provides a powerful tool in environmental monitoring. Radionuclide effluents have been discharged, under authorization, into the Irish Sea from BNFL (British Nuclear Fuels Pic.) sites at Sellafield and Springfields since 1952. The quantitative mapping of this anthropogenic radioactivity in estuarine intertidal zones is crucial for absolute interpretations of radionuclide transport. The spatial resolutions of traditional approaches e.g. point sampling and airborne gamma surveys are insufficient to support geomorphic interpretations of the fate of radionuclides in estuaries. The research presented in this thesis develops the use of airborne remote sensing to derive high-resolution synoptic data on the distribution of anthropogenic radionuclides in the intertidal areas of the Ribble Estuary, Lancashire, UK. From multidate surface sediment samples a significant relationship was identified between the Sellafield-derived 137 Cs and 241 Am and clay content (r 2 = 0.93 and 0.84 respectively). Detailed in situ, and laboratory, reflectance (0.4-2.5μm) experiments demonstrated that significant relationships exist between Airborne Thematic Mapper (ATM) simulated reflectance and intertidal sediment grain-size. The spectral influence of moisture on the reflectance characteristics of the intertidal area is also evident. This had substantial implications for the timing of airborne image acquisition. Low-tide Daedalus ATM imagery (Natural Environmental Research Council) was collected of the Ribble Estuary on May 30th 1997. Preprocessing and linear unmixing of the imagery allowed accurate sub-pixel determinations of sediment clay content distributions (r 2 = 0.81). Subsequently, the established relationships between 137 Cs and 241 Am and sediment grain-size enabled the radionuclide activity distributions across the entire intertidal area (92 km 2 ) to be mapped at a geomorphic scale (1.75 m). The accuracy of these maps

Survey monitoring of environmental radioactivity in Busan area

Energy Technology Data Exchange (ETDEWEB)

Yang, H. S.; Lee, J. [Busan Regional Monitoring Station, Busan (Korea, Republic of)

2000-12-15

At Pusan Regional Monitoring Station in Busan have been measured periodically in 2000 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Pusan, vegetables, fishes, shellfish, drinking water (total 23ea) samples were taken from sampling sites which were selected by KlNS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Busan area

Energy Technology Data Exchange (ETDEWEB)

Yang, Han Soeb; Jang, Young A. [Busan Regional Monitoring Station, Busan (Korea, Republic of)

2003-12-15

At Regional Radioactivity Monitoring Station in Pusan have been measured periodically in 2003 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Busan foodstuffs, dust, drinking water (total 24ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Busan area

International Nuclear Information System (INIS)

Yang, Han Soeb; Jang, Young A.

2003-12-01

At Regional Radioactivity Monitoring Station in Pusan have been measured periodically in 2003 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Gamma nuclides in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Busan foodstuffs, dust, drinking water (total 24ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma nuclide for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzing an gamma nuclide concentration in environmental samples in Pusan are fee of radiological contaminants

Radiofrequency electromagnetic fields in the Cookridge area of Leeds

CERN Document Server

Fuller, K; Judd, P M; Lowe, A J; Shaw, J

2002-01-01

On the 8 and 9 May 2002 representatives of the National Radiological Protection Board (NRPB) performed a radiofrequency electromagnetic field survey in the Cookridge area of Leeds in order to assess exposure to radio signals from transmitters mounted on a water tower/a lattice tower and a radio station tower. Guidelines on limiting exposure to radio signals have been published by NRPB and the International Commission on Non-Ionizing Radiation Protection (ICNIRP). These guidelines are designed to prevent established adverse effects on human health. During this survey, the total exposures due to all radio signals from 30 MHz to 18000 MHz (18 GHz) were measured. This frequency range was chosen as it includes mobile phone base station transmissions, which are at around 900 and 1800 MHz and super high frequency (SHF) transmissions from most of the large microwave dish antennas mounted on the towers. In addition, other major sources of radiofrequency electromagnetic fields in the environment such as broadcast radio...

ESA CryoVEx 2014 - Airborne ASIRAS radar and laser scanner measurements during 2014 CryoVEx campaign in the Arctic

DEFF Research Database (Denmark)

Hvidegaard, S. M.; Nielsen, J. E.; Sørensen, L. Sandberg

the penetration depth of the ASIRAS radar. An opportunity site on the Greenland Ice Sheet was surveyed near Jakobshavn Isbræ. No other ground experiments were coordinated with the CryoVEx campaing on the Greenland Ice Sheet. The CryoVEx 2014 campaign was a success and the processed data is of high quality......This report outlines the airborne field operations with the ESA airborne Ku‐band interferometric radar (ASIRAS), coincident airborne laser scanner (ALS) and vertical photography to acquire data over sea‐ and land ice along validation sites and CryoSat‐2 ground tracks. The airborne campaign...... in the Beaufort Sea lead by US office of Naval Research (ONR) and north of Greenland as a dedicated ESA CryoVEx initiative. In addition, selected CryoSat‐2 ground tracks were under‐flown in the Lincoln Sea from CFS Alert, North of Greenland and Svalbard from St. Nord and Longyearbyen. Several of the flights...

Assessment of long-range kinematic GPS positioning errors by comparison with airborne laser altimetry and satellite altimetry

DEFF Research Database (Denmark)

Zhang, X.H.; Forsberg, René

2007-01-01

Long-range airborne laser altimetry and laser scanning (LIDAR) or airborne gravity surveys in, for example, polar or oceanic areas require airborne kinematic GPS baselines of many hundreds of kilometers in length. In such instances, with the complications of ionospheric biases, it can be a real...... challenge for traditional differential kinematic GPS software to obtain reasonable solutions. In this paper, we will describe attempts to validate an implementation of the precise point positioning (PPP) technique on an aircraft without the use of a local GPS reference station. We will compare PPP solutions...... of the Arctic Ocean north of Greenland, near-coincident in time and space with the ICESat satellite laser altimeter. Both of these flights were more than 800 km long. Comparisons between different GPS methods and four different software packages do not suggest a clear preference for any one, with the heights...

Airborne geoid mapping of land and sea areas of East Malaysia

Science.gov (United States)

Jamil, H.; Kadir, M.; Forsberg, R.; Olesen, A.; Isa, M. N.; Rasidi, S.; Mohamed, A.; Chihat, Z.; Nielsen, E.; Majid, F.; Talib, K.; Aman, S.

2017-02-01

This paper describes the development of a new geoid-based vertical datum from airborne gravity data, by the Department of Survey and Mapping Malaysia, on land and in the South China Sea out of the coast of East Malaysia region, covering an area of about 610,000 square kilometres. More than 107,000 km flight line of airborne gravity data over land and marine areas of East Malaysia has been combined to provide a seamless land-to-sea gravity field coverage; with an estimated accuracy of better than 2.0 mGal. The iMAR-IMU processed gravity anomaly data has been used during a 2014-2016 airborne survey to extend a composite gravity solution across a number of minor gaps on selected lines, using a draping technique. The geoid computations were all done with the GRAVSOFT suite of programs from DTU-Space. EGM2008 augmented with GOCE spherical harmonic model has been used to spherical harmonic degree N = 720. The gravimetric geoid first was tied at one tide-gauge (in Kota Kinabalu, KK2019) to produce a fitted geoid, my_geoid2017_fit_kk. The fitted geoid was offset from the gravimetric geoid by +0.852 m, based on the comparison at the tide-gauge benchmark KK2019. Consequently, orthometric height at the six other tide gauge stations was computed from HGPS Lev = hGPS - Nmy_geoid2017_.t_kk. Comparison of the conventional (HLev) and GPS-levelling heights (HGPS Lev) at the six tide gauge locations indicate RMS height difference of 2.6 cm. The final gravimetric geoidwas fitted to the seven tide gauge stations and is known as my_geoid2017_fit_east. The accuracy of the gravimetric geoid is estimated to be better than 5 cm across most of East Malaysia land and marine areas

Airborne iodine-125 arising from surface contamination

International Nuclear Information System (INIS)

Kwok, C.S.; Hilditch, T.E.

1982-01-01

Measurements of airborne 125 I were made during the subdivision of 740 MBq stocks of 125 I iodide solution in a hospital dispensary. Within the fume cupboard the mean airborne 125 I concentration was 3.5 +- 2.9 kBqm -3 . No airborne concentration contamination was found outside the fume cupboard during these dispensing sessions. The airborne 125 I concentration arising from deliberate surface contamination (50 μl, 3.7-6.3 MBq) of the top of a lead pot was measured at a height simulating face level at an open work bench. There was a progressive fall in airborne concentration over seven days but even then the level was still significantly above background. Measurements made with the extraction system of the fume cupboard in operation were 2-3 times lower. (U.K.)

Large-scale radon hazard evaluation in the Oslofjord region of Norway utilizing indoor radon concentrations, airborne gamma ray spectrometry and geological mapping

International Nuclear Information System (INIS)

Smethurst, Mark Andrew; Strand, Terje; Sundal, Aud Venke; Rudjord, Anne Liv

2008-01-01

We test whether airborne gamma ray spectrometer measurements can be used to estimate levels of radon hazard in the Oslofjord region of Norway. We compile 43,000 line kilometres of gamma ray spectrometer data from 8 airborne surveys covering 10,000 km 2 and compare them with 6326 indoor radon measurements. We find a clear spatial correlation between areas with elevated concentrations of uranium daughters in the near surface of the ground and regions with high incidence of elevated radon concentrations in dwellings. This correlation permits cautious use of the airborne data in radon hazard evaluation where direct measurements of indoor radon concentrations are few or absent. In radon hazard evaluation there is a natural synergy between the mapping of radon in indoor air, bedrock and drift geology mapping and airborne gamma ray surveying. We produce radon hazard forecast maps for the Oslofjord region based on a spatial union of hazard indicators from all four of these data sources. Indication of elevated radon hazard in any one of the data sets leads to the classification of a region as having an elevated radon hazard potential. This approach is inclusive in nature and we find that the majority of actual radon hazards lie in the assumed elevated risk regions

AERIAL RADIOLOGICAL SURVEYS

International Nuclear Information System (INIS)

Proctor, A.E.

1997-01-01

Measuring terrestrial gamma radiation from airborne platforms has proved to be a useful method for characterizing radiation levels over large areas. Over 300 aerial radiological surveys have been carried out over the past 25 years including U.S. Department of Energy (DOE) sites, commercial nuclear power plants, Formerly Utilized Sites Remedial Action Program/Uranium Mine Tailing Remedial Action Program (FUSRAP/UMTRAP) sites, nuclear weapons test sites, contaminated industrial areas, and nuclear accident sites. This paper describes the aerial measurement technology currently in use by the Remote Sensing Laboratory (RSL) for routine environmental surveys and emergency response activities. Equipment, data-collection and -analysis methods, and examples of survey results are described

Geophysical investigations on the Vaalputs radioactive waste disposal site in the Republic of South Africa

International Nuclear Information System (INIS)

Andersen, N.J.B.; Faurie, J.N.; Fernandez, L.M.

1986-01-01

As the rocks of the Namaqualand Metamorphic Complex are sand-covered in the area of interest, extensive airborne and ground geophysical surveys were undertaken to assist with the evaluation of the regional and local geology, as well as to locate and avoid possible mineralization. A medium sensitivity aeromagnetic survey and an airborne INPUT survey were used to locate potentially mineralized kimberlite and noritoid intrusions. After airborne detection, these targets were followed up on the ground using electromagnetic and resistivity techniques. Subsequent drilling proved them to be unmineralized. A thermal infrared line-scan survey was used in conjunction with the aeromagnetics to evaluate the structural geology and assist with the location of groundwater. Continuous seismics refraction profiling was used to locate an area of rippable overburden (i.e. having a seismic velocity of less than 1 500 m/s) and depth greater than 10 m for the excavation of the low-level waste trenches. All boreholes were radiometrically logged. Since the Vaalputs area is entirely sand-covered it was essential to use geophysical techniques to evaluate the subsurface geology, and to avoid placing the facility in an area of economic mineralization

Airborne radionuclides in the proglacial environment as indicators of sources and transfers of soil material.

Science.gov (United States)

Łokas, Edyta; Wachniew, Przemysław; Jodłowski, Paweł; Gąsiorek, Michał

2017-11-01

A survey of artificial ( 137 Cs, 238 Pu, 239+240 Pu, 241 Am) and natural ( 226 Ra, 232 Th, 40 K, 210 Pb) radioactive isotopes in proglacial soils of an Arctic glacier have revealed high spatial variability of activity concentrations and inventories of the airborne radionuclides. Soil column 137 Cs inventories range from below the detection limit to nearly 120 kBq m -2 , this value significantly exceeding direct atmospheric deposition. This variability may result from the mixing of materials characterised by different contents of airborne radionuclides. The highest activity concentrations observed in the proglacial soils may result from the deposition of cryoconites, which have been shown to accumulate airborne radionuclides on the surface of glaciers. The role of cryoconites in radionuclide accumulation is supported by the concordant enrichment of the naturally occurring airborne 210 Pb in proglacial soil cores showing elevated levels of artificial radionuclides. The lithogenic radionuclides show less variability than the airborne radionuclides because their activity concentrations are controlled only by the mixing of material derived from the weathering of different parent rocks. Soil properties vary little within and between the profiles and there is no unequivocal relationship between them and the radionuclide contents. The inventories reflect the pathways and time variable inputs of soil material to particular sites of the proglacial zone. Lack of the airborne radionuclides reflects no deposition of material exposed to the atmosphere after the 1950s or its removal by erosion. Inventories above the direct atmospheric deposition indicate secondary deposition of radionuclide-bearing material. Very high inventories indicate sites where transport pathways of cryoconite material terminated. Copyright © 2017 Elsevier Ltd. All rights reserved.

Electromagnetic Properties Analysis on Hybrid-driven System of Electromagnetic Motor

Science.gov (United States)

Zhao, Jingbo; Han, Bingyuan; Bei, Shaoyi

2018-01-01

The hybrid-driven system made of permanent-and electromagnets applied in the electromagnetic motor was analyzed, equivalent magnetic circuit was used to establish the mathematical models of hybrid-driven system, based on the models of hybrid-driven system, the air gap flux, air-gap magnetic flux density, electromagnetic force was proposed. Taking the air-gap magnetic flux density and electromagnetic force as main research object, the hybrid-driven system was researched. Electromagnetic properties of hybrid-driven system with different working current modes is studied preliminary. The results shown that analysis based on hybrid-driven system can improve the air-gap magnetic flux density and electromagnetic force more effectively and can also guarantee the output stability, the effectiveness and feasibility of the hybrid-driven system are verified, which proved theoretical basis for the design of hybrid-driven system.

[Distribution of airborne fungi, particulate matter and carbon dioxide in Seoul metropolitan subway stations].

Science.gov (United States)

Kim, Ki Youn; Park, Jae Beom; Kim, Chi Nyon; Lee, Kyung Jong

2006-07-01

The aims of this study were to examine the level of airborne fungi and environmental factors in Seoul metropolitan subway stations and to provide fundamental data to protect the health of subway workers and passengers. The field survey was performed from November in 2004 to February in 2005. A total 22 subway stations located at Seoul subway lines 1-4 were randomly selected. The measurement points were subway workers' activity areas (station office, bedroom, ticket office and driver's seat) and the passengers' activity areas (station precincts, inside train and platform). Air sampling for collecting airborne fungi was carried out using a one-stage cascade impactor. The PM and CO2 were measured using an electronic direct recorder and detecting tube, respectively. In the activity areas of the subway workers and passengers, the mean concentrations of airborne fungi were relatively higher in the workers' bedroom and station precinct whereas the concentration of particulate matter, PM10 and PM2.5, were relatively higher in the platform, inside the train and driver's seat than in the other activity areas. There was no significant difference in the concentration of airborne fungi between the underground and ground activity areas of the subway. The mean PM10 and PM2.5 concentration in the platform located at underground was significantly higher than that of the ground (psubway line 1-4 were not serious enough to cause respiratory disease in subway workers and passengers. This indicates that there is little correlation between airborne fungi and particulate matter.

A combined approach of remote sensing and airborne electromagnetics to determine the volume of polynya sea ice in the Laptev Sea

Directory of Open Access Journals (Sweden)

L. Rabenstein

2013-06-01

Full Text Available A combined interpretation of synthetic aperture radar (SAR satellite images and helicopter electromagnetic (HEM sea-ice thickness data has provided an estimate of sea-ice volume formed in Laptev Sea polynyas during the winter of 2007/08. The evolution of the surveyed sea-ice areas, which were formed between late December 2007 and middle April 2008, was tracked using a series of SAR images with a sampling interval of 2–3 days. Approximately 160 km of HEM data recorded in April 2008 provided sea-ice thicknesses along profiles that transected sea ice varying in age from 1 to 116 days. For the volume estimates, thickness information along the HEM profiles was extrapolated to zones of the same age. The error of areal mean thickness information was estimated to be between 0.2 m for younger ice and up to 1.55 m for older ice, with the primary error source being the spatially limited HEM coverage. Our results have demonstrated that the modal thicknesses and mean thicknesses of level ice correlated with the sea-ice age, but that varying dynamic and thermodynamic sea-ice growth conditions resulted in a rather heterogeneous sea-ice thickness distribution on scales of tens of kilometers. Taking all uncertainties into account, total sea-ice area and volume produced within the entire surveyed area were 52 650 km2 and 93.6 ± 26.6 km3. The surveyed polynya contributed 2.0 ± 0.5% of the sea-ice produced throughout the Arctic during the 2007/08 winter. The SAR-HEM volume estimate compares well with the 112 km3 ice production calculated with a~high-resolution ocean sea-ice model. Measured modal and mean-level ice thicknesses correlate with calculated freezing-degree-day thicknesses with a factor of 0.87–0.89, which was too low to justify the assumption of homogeneous thermodynamic growth conditions in the area, or indicates a strong dynamic thickening of level ice by rafting of even thicker ice.

SGA-WZ: A New Strapdown Airborne Gravimeter

DEFF Research Database (Denmark)

Huang, Yangming; Olesen, Arne Vestergaard; Wu, Meiping

2012-01-01

Inertial navigation systems and gravimeters are now routinely used to map the regional gravitational quantities from an aircraft with mGal accuracy and a spatial resolution of a few kilometers. However, airborne gravimeter of this kind is limited by the inaccuracy of the inertial sensor performance......, the integrated navigation technique and the kinematic acceleration determination. As the GPS technique developed, the vehicle acceleration determination is no longer the limiting factor in airborne gravity due to the cancellation of the common mode acceleration in differential mode. A new airborne gravimeter...... and discussion of the airborne field test results are also given....

Spectrometric aerial survey as a new tool for geological survey and mining prospecting

International Nuclear Information System (INIS)

Cambon, R.

1997-01-01

Airborne survey for radioactive minerals started around 1945. The limited sensitivity of the tools used, the difficulties found for the topographic and training effect corrections, made difficult the evaluation of the results. The technical progresses realized in the recent past years in electronic and computer sciences allowed to overcome these difficulties and gave to the method all its potentialities. With the aerial spectrometric survey, a new step was made, because this method can be used for other topics than radioactive prospection such as geological survey and mining prospection for metallic and industrial minerals. The spectrometric method is based on the possibility to measure photopeak energies (gamma radiation) emitted by radioactive minerals and discriminate between them those emitted by U238, TI 208 and K40 respectively daughter products of uranium, thorium and potassium. For airborne survey, one consider that measuring instruments will allow to pick-up 80% of the radioactive emission concerning the first 15 to 30 centimetres of ground (1 metre maximum). The use of this method for geological and mineral exploration is based on the assumption that different rock types or ore bearing rock types are composed of certain amounts of rock forming minerals which comprise specific quantities of radioactive elements such as potassium, uranium and thorium (cf: Gabelman 77). To be able to evaluate the results of the spectrometric survey it will be necessary to know roughly the behaviour of the different radioactive elements through a complete geological cycle. (author)

2008 US Army Corps of Engineers (USACE) Joint Airborne Lidar Bathymetry Technical Center of Expertise (JALBTCX) Topobathy Lidar: North Carolina

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These files contain topographic lidar data collected by the Compact Hydrographic Airborne Rapid Total Survey (CHARTS) system along the coast of North Carolina near...

Airborne gamma-ray spectrometer and magnetometer survey: Norton Bay Quadrangle (Alaska). Final report

International Nuclear Information System (INIS)

1980-01-01

During the months of July, August, and September 1979, an airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over ten 3 0 x 1 0 NTMS quadrangles of West-Central Alaska. The results obtained over the Norton Bay Map area are discussed. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps and flight path maps. The histograms and the multiparameter are presented with the anomaly maps and flight path map in a separate volume. A total of twenty (20) uranium anomalies have been indicated on the interpretation map. No thorium anomalies were found. The uranium anomalies are all weak and generally have only U/K or U/T expression. Often the uranium concentration within the zone is low, and generally is less than 2.5 ppM. Only zones 9, with an average of 3.0 ppM eU, and 14, with 2.6 ppm have above average uranium content. Zone 14 is also the only uranium anomaly with combined U/K and U/T ratio anomalies. No single uranium anomaly is believed to represent an economic follow-up target. The most prospective area appears to be the elongate zone of generally high uranium content, formed by the deposits of the Shaktolik group, to the east of the Ungalik conglomerate. This zone flanks an elongate area of relatively strong shallow magnetic sources, interpreted to be related to a monozonitic intrusive of which the Christmas mountain forms part. This intrusive rock contains in other neighboring areas often high thorium and uranium concentrations and may here as well served as a possible source of uranium deposits

Geophysical investigations of the Romuvaara area, Finland

International Nuclear Information System (INIS)

Saksa, P.; Paananen, M.

1991-06-01

In the study area of Romuvaara, investigations have been carried out during 1987 - 90 with the aim of finding out whether the polyphasically deformed Precambrian gneiss complex is suitable for the final disposal of spent nuclear fuel. The bedrock has been studied by geological, geophysical, geohydrological and geochemical methods. Airborne, ground and borehole geophysical surveys were used in studying the rock type distribution, fracturing and hydraulic conductivity of the bedrock to a depth of one kilometre. Airborne surveys (magnetic, radiometric and two electromagnetic methods) and ground surveys (VLF and VLF-R, magnetic and soil radar methods) were useful in distinguishing the metadiabases, amphibolites and granodiorites from the less magnetized migmatites. The electromagnetic and seismic refraction surveys were used in locating crushed and fractured zones. The rock type distribution was studied by single-hole logging of susceptibility, natural γ radiation and radiometric γ-γ -density. Electrical and acoustic logging served the mapping of fractures and the interpretation of water injection tests. The flow conditions in the boreholes were studied by fluid logging and tube-wave sounding. The rock volume surrounding the boreholes was mapped by borehole radar with a frequency of 22 MHz. The upper parts of the boreholes were also studied by vertical radar profiling (VRP). Larger volumes of rock were mapped by vertical seismic profiling (VSP) using 4 - 5 transmitter shotholes per borehole

The internal layering of Pine Island Glacier, West Antarctica, from airborne radar-sounding data

DEFF Research Database (Denmark)

Karlsson, Nanna Bjørnholt; Rippin, David; Vaughan, David

2010-01-01

This paper presents an overview of internal layering across Pine Island Glacier, West Antarctica, as measured from airborne-radar data acquired during a survey conducted by the British Antarctic Survey and the University of Texas in the 2004/05 season. Internal layering is classified according...... to type (continuous/discontinuous/missing) and the results compared with InSAR velocities. Several areas exhibit disruption of internal layers that is most likely caused by large basal shear stresses. Signs of changes in flow were identified in a few inter-tributary areas, but overall the layering...

Airborne gamma spectrometric survey in the Chernobyl exclusion zone based on oktokopter UAV type

International Nuclear Information System (INIS)

Zabulonov, Yu.L.; Burtnyak, V.M.; Zolkin, I.O.

2015-01-01

The results of field studies of radioactive contamination condition of RWTSP ''Red Forest'' and ''Neftebaza'' in the Chernobyl zone, obtained by the authors in June 2015 are represented. The technique of detection of local inhomogeneities on the soil surface without contrasting borders by airborne gamma spectrometry from the board of oktokopter UAV type is worked through. The technique of searching and contouring of hidden burial of radioactive waste is practiced

Electromagnetic Gowdy universe

International Nuclear Information System (INIS)

Charach, C.

1979-01-01

Following Gowdy and Berger we construct an inhomogeneous closed electromagnetic universe with three-torus topology. This model is obtained as a result of the homogeneity breaking in the electromagnetic Bianchi type-I universe and contains interacting gravitational and electromagnetic waves. This cosmological solution provides an exactly solvable model for the study of the nonlinear fully relativistic regime of coupled electromagnetic and gravitational fields in the early universe. The asymptotic behavior is considered (i) in the vicinity of the initial singularity and (ii) in the high-frequency limit. It is shown that the effects of coupling between electromagnetic and gravitational waves cause an evolution which is significantly different from that of the vacuum model. The influence of the primordial homogeneous electromagnetic field on the dynamics of the model is also discussed

Survey monitoring of environmental radioactivity in Gunsan area

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Ho; Ro, Jeong Suk [Kunsan Regional Radioactivity Monitoring Station, Gunsan (Korea, Republic of)

2001-01-15

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2000 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of {sup 137}Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant Changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are I fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Gunsan area

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Ho; Ro, Jeong Suk [Kunsan Regional Radioactivity Monitoring Station, Gunsan (Korea, Republic of)

2002-12-15

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2002 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of {sup 137}Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are fee of radiological contaminants.

Survey monitoring of environmental radioactivity in Gunsan area

International Nuclear Information System (INIS)

Kim, Byoung Ho; Ro, Jeong Suk

2002-12-01

At Regional Radioactivity Monitoring Station in Kunsan have been measured priodically in 2002 gross beta activities in the airborne dust, fallout, precipitation and tap water and gamma exposure rates. Artificial radionuclide of 137 Cs in airborne dust, fallout and precipitation have also been monitored at the station. As a part of environmental radiation/radioactivity distribution survey around Jeon-buk, vegetables, fishes, shellfishes, drinking water (total 33ea) samples were taken from sampling sites which were selected by KINS. We analysis gamma isotope for all. No significant changes from the previous survey have been found in both beta activities and gamma exposure rates. As the results of analyzig an artificial nuclide concentration in living environmental sample in Jeon-buk are fee of radiological contaminants

Aerial radiometric and magnetic survey: Lander National Topographic Map, Wyoming

International Nuclear Information System (INIS)

1979-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Lander National Topographic Map NK12-6 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Challenges and Opportunities of Airborne Metagenomics

KAUST Repository

Behzad, H.

2015-05-06

Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles.

Diurnal variations of airborne fungal spores concentration in the town and rural area

Directory of Open Access Journals (Sweden)

Idalia Kasprzyk

2012-12-01

Full Text Available Airborne fungal spores were monitored in 2001-2002 in Rzeszów (town and its neighborhood. The aim of investigations was to ascertain if there were differences in diurnal variations of airborne fungal spores concentration between town and rural area. The sampling was carried out using volumetric method. Traps were located at the same heights - app. 12 m. Airborne spores were sampled continuously. Microscopical slides were prepared for each day. Analysis was carried out on one longitudinal band of 48 mm long divided into 24 segments corresponding following hours of day. The results were expressed as mean number of fungal spores per cubic meter per 24 hours. For this survey, five geni of allergenic fungi were selected: Alternaria, Botrytis, Cladosporium, Epicoccum, Ganoderma. The concentrations of their airborne spores were high or very high. It was calculated theoretical day, where the hourly count was the percentage mean of number of spores at that time every chosen day without rainfall from 2001 and 2001 years. The diurnal periodicity of Alternaria, Cladosporium, Epicoccum and Ganoderma showed one peak, while Botrytis two. Anamorphic spores peaked in the afternoon, while their minima occurred in the morning. The highest concentrations of Ganoderma basidiospores were at down or at night, but minima during the day. There were no clear differences in the peak values between two studied sites. The results indicate that maximum concentrations of all spores generally occurred a few hour earlier in the rural area than in the town. Probably, in the rural area airborne spores came from many local sources and their diurnal periodicity reflected rhythm of spore liberation. Towns are characterized by specific microclimate with higher temperature and wind blowing to the centre. In Rzeszów fungal spores could be transported outside and carried out by wind from distant sources. This study showed, among others, that habitat conditions are an important factors

An aerial radiological survey of Areas 16 and 30, Nevada Test Site: Date of survey: June 1983

International Nuclear Information System (INIS)

Bluitt, C.M.

1986-10-01

An aerial radiological survey of the Nevada Test Site (NTS) was conducted for the US Department of Energy (DOE). The survey period was from 1 June to 16 June 1983, during which airborne measurements were obtained over Areas 16 and 30. The data were used to generate exposure rate, cobalt-60, and cesium-137 spatial distribution maps. The aerial survey results are expressed as exposure rate, cesium-137, and cobalt-60 isopleth contours, superimposed on NTS maps. 12 refs., 16 figs

Applications of high resolution airborne magnetic and radiometric data in the Barberton Greenstone Belt of South Africa

International Nuclear Information System (INIS)

Moore, C.

1994-01-01

We investigated the data obtained from a geophysical survey of the Greenstone Belt in the Barberton mountain land in the Transvaal, South Africa. A geological map is derived from the airborne magnetic and radiometric survey which differs significantly from the published geological map, particularly in the eastern are of the survey. There is no evidence contained within the geological data to suggest that the Greenstone Belt extends to a depth greater that 3 kilometers. The major geological constituents of the Barberton mountain land displays distinctive and diagnostic radiometric signatures, enabling accurate lithologic discrimination. 63 refs

VETEM -- a very early time electromagnetic system -- year 2

International Nuclear Information System (INIS)

Pellerin, L.; Pfeifer, M.C.; Labson, V.F.

1996-01-01

In electrically conductive conditions common in environmental characterization studies the minimum depth of investigation for traditional electromagnetic (EM) sounding techniques is roughly 5 meters, while ground penetrating radar (GPR) systems often investigate no more than the top meter or so when clay minerals are present in the soil. Bridging this gap is essential to the characterization of buried waste, contaminant plumes, and other environmental and hydrogeological targets located in the shallow subsurface. The Very Early Time Electromagnetic (VETEM) system is designed to ascertain the conductivity and dielectric properties of the shallow subsurface in conductive terrain. Hence, the one-dimensional (1-D) and three-dimensional (3-D) numerical modeling algorithms, developed in the first year of the project, contain the full solution to the EM problem including both displacement and conduction currents. The VETEM system fills a gap between EM and GPR, but all three methods are necessary to successfully image the shallow subsurface. To achieve the goal of fully 3-D subsurface imaging, the VETEM project is hosting the Electromagnetic Integrated Demonstration (EMID) at the Idaho National Engineering Laboratory's Cold Test Pit (INEL's CTP). Over a dozen EM systems will acquire data over the same survey area for interpretation in conjunction with the VETEM team. The prototype time-domain instrument employs a magnetic dipole transmitter and receiver and operates from 10 nano-second to a micro-second. The USGS high frequency sounder (HFS), which served as the VETEM proof-of-concept, uses the same antenna geometry as the time-domain instrument and acquires data from 30 kHz to 30 MHz. The first VETEM survey was recently conducted at the INEL's CTP as a part of the EMID. The electromagnetic migration technique is being investigated for interpretation of the VETEM data

Plane and geodetic surveying

CERN Document Server

Johnson, Aylmer

2014-01-01

IntroductionAim And ScopeClassification Of SurveysThe Structure Of This BookGeneral Principles Of SurveyingErrorsRedundancyStiffnessAdjustmentPlanning And Record KeepingPrincipal Surveying ActivitiesEstablishing Control NetworksMappingSetting OutResectioningDeformation MonitoringAngle MeasurementThe Surveyor's CompassThe ClinometerThe Total StationMaking ObservationsChecks On Permanent AdjustmentsDistance MeasurementGeneralTape MeasurementsOptical Methods (Tachymetry)Electromagnetic Distance Measurement (EDM)Ultrasonic MethodsGNSSLevellingTheoryThe InstrumentTechniqueBookingPermanent Adjustmen

Monitoring of airborne bacteria and aerosols in different wards of hospitals - Particle counting usefulness in investigation of airborne bacteria.

Science.gov (United States)

Mirhoseini, Seyed Hamed; Nikaeen, Mahnaz; Khanahmd, Hossein; Hatamzadeh, Maryam; Hassanzadeh, Akbar

2015-01-01

The presence of airborne bacteria in hospital environments is of great concern because of their potential role as a source of hospital-acquired infections (HAI). The aim of this study was the determination and comparison of the concentration of airborne bacteria in different wards of four educational hospitals, and evaluation of whether particle counting could be predictive of airborne bacterial concentration in different wards of a hospital. The study was performed in an operating theatre (OT), intensive care unit (ICU), surgery ward (SW) and internal medicine (IM) ward of four educational hospitals in Isfahan, Iran. A total of 80 samples were analyzed for the presence of airborne bacteria and particle levels. The average level of bacteria ranged from 75-1194 CFU/m (3) . Mean particle levels were higher than class 100,000 cleanrooms in all wards. A significant correlation was observed between the numbers of 1-5 µm particles and levels of airborne bacteria in operating theatres and ICUs. The results showed that factors which may influence the airborne bacterial level in hospital environments should be properly managed to minimize the risk of HAIs especially in operating theaters. Microbial air contamination of hospital settings should be performed by the monitoring of airborne bacteria, but particle counting could be considered as a good operative method for the continuous monitoring of air quality in operating theaters and ICUs where higher risks of infection are suspected.

Electromagnetic Sampo monitoring soundings at Olkiluoto 2010

International Nuclear Information System (INIS)

Korhonen, K.; Korpisalo, A.; Ojamo, H.

2010-12-01

The Geological Survey of Finland has carried out electromagnetic frequency-domain depth soundings at fixed measurement stations in Olkiluoto annually since 2004. The purpose of the soundings is to monitor the groundwater conditions in the vicinity of the ONKALO rock characterization facility which will ultimately be part of the final nuclear waste disposal facility for the Finnish nuclear power companies. A new monitoring survey was carried out at the turn of May-June 2010. The survey resulted in 38 successfully performed soundings at 10 stations. The data set spanning the time period of 2004 to 2010 was interpreted with layered-earth models. Most of the interpretations indicate no systematic changes in the level of deep saline groundwater. However, at one station there are indications of a systematic rise in the groundwater level. (orig.)

Joint 3D Inversion of ZTEM Airborne and Ground MT Data with Application to Geothermal Exploration

Science.gov (United States)

Wannamaker, P. E.; Maris, V.; Kordy, M. A.

2017-12-01

ZTEM is an airborne electromagnetic (EM) geophysical technique developed by Geotech Inc® where naturally propagated EM fields originating with regional and global lightning discharges (sferics) are measured as a means of inferring subsurface electrical resistivity structure. A helicopter-borne coil platform (bird) measuring the vertical component of magnetic (H) field variations along a flown profile is referenced to a pair of horizontal coils at a fixed location on the ground in order to estimate a tensor H-field transfer function. The ZTEM method is distinct from the traditional magnetotelluric (MT) method in that the electric (E) fields are not considered because of the technological challenge of measuring E-fields in the dielectric air medium. This can lend some non-uniqueness to ZTEM interpretation because a range of conductivity structures in the earth depending upon an assumed background earth resistivity model can fit ZTEM data to within tolerance. MT data do not suffer this particular problem, but they are cumbersome to acquire in their common need for land-based transport often in near-roadless areas and for laying out and digging the electrodes and H coils. The complementary nature of ZTEM and MT logistics and resolution has motivated development of schemes to acquire appropriate amounts of each data type in a single survey and to produce an earth image through joint inversion. In particular, consideration is given to surveys where only sparse MT soundings are needed to drastically reduce the non-uniqueness associated with background uncertainty while straining logistics minimally. Synthetic and field data are analysed using 2D and 3D finite element platforms developed for this purpose. Results to date suggest that indeed dense ZTEM surveys can provide detailed heterogeneous model images with large-scale averages constrained by a modest number of MT soundings. Further research is needed in determining the allowable degree of MT sparseness and the

Airborne Lidar Surface Topography (LIST) Simulator

Science.gov (United States)

Yu, Anthony W.; Krainak, Michael A.; Harding, David J.; Abshire, James B.; Sun, Xiaoli; Cavanaugh, John; Valett, Susan; Ramos-Izquierdo, Luis; Winkert, Tom; Plants, Michael;

Digital airborne camera introduction and technology

CERN Document Server

Sandau, Rainer

2014-01-01

The last decade has seen great innovations on the airborne camera. This book is the first ever written on the topic and describes all components of a digital airborne camera ranging from the object to be imaged to the mass memory device.

Detection of airborne Legionella while showering using liquid impingement and fluorescent in situ hybridization (FISH).

Science.gov (United States)

Deloge-Abarkan, Magali; Ha, Thi-Lan; Robine, Enric; Zmirou-Navier, Denis; Mathieu, Laurence

2007-01-01

Aerosols of water contaminated with Legionella bacteria constitute the only mode of exposure for humans. However, the prevention strategy against this pathogenic bacteria risk is managed through the survey of water contamination. No relationship linked the Legionella bacteria water concentration and their airborne abundance. Therefore, new approaches in the field of the metrological aspects of Legionella bioaerosols are required. This study was aimed at testing the main principles for bioaerosol collection (solid impaction, liquid impingement and filtration) and the in situ hybridization (FISH) method, both in laboratory and field assays, with the intention of applying such methodologies for airborne Legionella bacteria detection while showering. An aerosolization chamber was developed to generate controlled and reproducible L. pneumophila aerosols. This tool allowed the identification of the liquid impingement method as the most appropriate one for collecting airborne Legionella bacteria. The culturable fraction of airborne L. pneumophila recovered with the liquid impingement principle was 4 and 700 times higher compared to the impaction and filtration techniques, respectively. Moreover, the concentrations of airborne L. pneumophila in the impinger fluid were on average 7.0 x 10(5) FISH-cells m(-3) air with the fluorescent in situ hybridization (FISH) method versus 9.0 x 10(4) CFU m(-3) air with the culture method. These results, recorded under well-controlled conditions, were confirmed during the field experiments performed on aerosols generated by hot water showers in health institutions. This new approach may provide a more accurate characterization of aerobiocontamination by Legionella bacteria.

Synoptic channel morphodynamics with topo-bathymetric airborne lidar: promises, pitfalls and research needs

Science.gov (United States)

Lague, D.; Launeau, P.; Gouraud, E.

2017-12-01

Topo-bathymetric airborne lidar sensors using a green laser penetrating water and suitable for hydrography are now sold by major manufacturers. In the context of channel morphodynamics, repeat surveys could offer synoptic high resolution measurement of topo-bathymetric change, a key data that is currently missing. Yet, beyond the technological promise, what can we really achieve with these sensors in terms of depth penetration and bathymetric accuracy ? Can all rivers be surveyed ? How easy it is to process this new type of data to get the data needed by geomorphologists ? Here we report on the use of the Optech Titan dual wavelength (1064 nm & 532 nm) operated by the universities of Rennes and Nantes (France) and deployed over several rivers and lakes in France, including repeat surveys. We will illustrate cases where the topo-bathymetric survey is complete, reaching up to 6 m in rivers and offers unprecedented data for channel morphology analysis over tens of kilometres. We will also present challenging cases for which the technology will never work, or for which new algorithms to process full waveform are required. We will illustrate new developments for automated processing of large datasets, including the critical step of water surface detection and refraction correction. In suitable rivers, airborne topo-bathymetric surveys offer unprecedented synoptic 3D data at very high resolution (> 15 pts/m² in bathy) and precision (better than 10 cm for the bathy) down to 5-6 meters depth, with a perfectly continuous topography to bathymetry transition. This presentation will illustrate how this new type of data, when combined with 2D hydraulics modelling offers news insights into the spatial variations of friction in relation to channel bedforms, and the connectivity between rivers and floodplains.

Three-dimensional inversion of multisource array electromagnetic data

Science.gov (United States)

Tartaras, Efthimios

Three-dimensional (3-D) inversion is increasingly important for the correct interpretation of geophysical data sets in complex environments. To this effect, several approximate solutions have been developed that allow the construction of relatively fast inversion schemes. One such method that is fast and provides satisfactory accuracy is the quasi-linear (QL) approximation. It has, however, the drawback that it is source-dependent and, therefore, impractical in situations where multiple transmitters in different positions are employed. I have, therefore, developed a localized form of the QL approximation that is source-independent. This so-called localized quasi-linear (LQL) approximation can have a scalar, a diagonal, or a full tensor form. Numerical examples of its comparison with the full integral equation solution, the Born approximation, and the original QL approximation are given. The objective behind developing this approximation is to use it in a fast 3-D inversion scheme appropriate for multisource array data such as those collected in airborne surveys, cross-well logging, and other similar geophysical applications. I have developed such an inversion scheme using the scalar and diagonal LQL approximation. It reduces the original nonlinear inverse electromagnetic (EM) problem to three linear inverse problems. The first of these problems is solved using a weighted regularized linear conjugate gradient method, whereas the last two are solved in the least squares sense. The algorithm I developed provides the option of obtaining either smooth or focused inversion images. I have applied the 3-D LQL inversion to synthetic 3-D EM data that simulate a helicopter-borne survey over different earth models. The results demonstrate the stability and efficiency of the method and show that the LQL approximation can be a practical solution to the problem of 3-D inversion of multisource array frequency-domain EM data. I have also applied the method to helicopter-borne EM

Marine Geoid Undulation Assessment Over South China Sea Using Global Geopotential Models and Airborne Gravity Data

Science.gov (United States)

Yazid, N. M.; Din, A. H. M.; Omar, K. M.; Som, Z. A. M.; Omar, A. H.; Yahaya, N. A. Z.; Tugi, A.

2016-09-01

Global geopotential models (GGMs) are vital in computing global geoid undulations heights. Based on the ellipsoidal height by Global Navigation Satellite System (GNSS) observations, the accurate orthometric height can be calculated by adding precise and accurate geoid undulations model information. However, GGMs also provide data from the satellite gravity missions such as GRACE, GOCE and CHAMP. Thus, this will assist to enhance the global geoid undulations data. A statistical assessment has been made between geoid undulations derived from 4 GGMs and the airborne gravity data provided by Department of Survey and Mapping Malaysia (DSMM). The goal of this study is the selection of the best possible GGM that best matches statistically with the geoid undulations of airborne gravity data under the Marine Geodetic Infrastructures in Malaysian Waters (MAGIC) Project over marine areas in Sabah. The correlation coefficients and the RMS value for the geoid undulations of GGM and airborne gravity data were computed. The correlation coefficients between EGM 2008 and airborne gravity data is 1 while RMS value is 0.1499.In this study, the RMS value of EGM 2008 is the lowest among the others. Regarding to the statistical analysis, it clearly represents that EGM 2008 is the best fit for marine geoid undulations throughout South China Sea.

Interpretation of moving EM dipole-dipole measurements using thin plate models

International Nuclear Information System (INIS)

Oksama, M.; Suppala, I.

1998-01-01

The three dimensional inversion of electromagnetic data is still rather problematic, because forward modelling programs are usually time consuming. They are based on numerical methods like finite element or integral equation methods. In the study a specific model for interpretation: two thin plates, which are located in a horizontally layered earth with two layers has been chosen. The model is rather limited, but in a few geological cases it is relevant. This interpretation method has been applied for two geophysical EM-systems, the slingram-system and the airborne electromagnetic system of the Geological Survey of Finland (GTK)

Interpretation of moving EM dipole-dipole measurements using thin plate models

Energy Technology Data Exchange (ETDEWEB)

Oksama, M.; Suppala, I. [Geological Survey of Finland, Espoo (Finland)

1998-09-01

The three dimensional inversion of electromagnetic data is still rather problematic, because forward modelling programs are usually time consuming. They are based on numerical methods like finite element or integral equation methods. In the study a specific model for interpretation: two thin plates, which are located in a horizontally layered earth with two layers has been chosen. The model is rather limited, but in a few geological cases it is relevant. This interpretation method has been applied for two geophysical EM-systems, the slingram-system and the airborne electromagnetic system of the Geological Survey of Finland (GTK) 5 refs.

Electromagnetic and thermal analysis of electromagnet for SMART control element drive mechanism

International Nuclear Information System (INIS)

Huh, H.; Kim, J. H.; Park, J. S.; Kim, Y. W.; Kim, J. I.

1999-01-01

A numerical electromagnetic and thermal analysis was performed for the electromagnet which is installed in the control element drive mechanism(CEDM) of the integral reactor SMART. A model for the electromagnetic analysis of the electromagnet was developed and theoretical bases for the model were established. Design parameters related to thrust force were identified, and the optimum design point was determined by analyzing the trend of the magnetic saturation with finite element method. Also It is important that the temperature of the electomagnet windings be maintained within the allowable limit of the insulation, since the electromagnet of CEDM is always supplied with current during the reactor operation. So the thermal analysis of the winding insulation which is composed of polyimide and air were performed by finite element method. The electromagnetic and thermal properties obtained here will be used as input for the optimization analysis of the electromagnet

Electromagnetic cellular interactions.

Science.gov (United States)

Cifra, Michal; Fields, Jeremy Z; Farhadi, Ashkan

2011-05-01

Chemical and electrical interaction within and between cells is well established. Just the opposite is true about cellular interactions via other physical fields. The most probable candidate for an other form of cellular interaction is the electromagnetic field. We review theories and experiments on how cells can generate and detect electromagnetic fields generally, and if the cell-generated electromagnetic field can mediate cellular interactions. We do not limit here ourselves to specialized electro-excitable cells. Rather we describe physical processes that are of a more general nature and probably present in almost every type of living cell. The spectral range included is broad; from kHz to the visible part of the electromagnetic spectrum. We show that there is a rather large number of theories on how cells can generate and detect electromagnetic fields and discuss experimental evidence on electromagnetic cellular interactions in the modern scientific literature. Although small, it is continuously accumulating. Copyright © 2010 Elsevier Ltd. All rights reserved.

Aerial radiometric and magnetic survey: Elko National Topographic Map, Nevada, Utah

International Nuclear Information System (INIS)

1979-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Elko national Topographic Map NK11-12 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included

Electromagnetic wave matching device

International Nuclear Information System (INIS)

Hirata, Yosuke; Mitsunaka, Yoshika; Hayashi, Ken-ichi; Ito, Yasuyuki.

1997-01-01

The present invention provides an electromagnetic wave matching capable of reducing a cost for the transmission system in a system of using electromagnetic waves for plasma heating of a thermonuclear reactor. Namely, incident electromagnetic waves are reflected by using a plurality of phase correction mirrors. The reflected electromagnetic waves are connected to an external transmission system through an exit. The phase correction mirrors have such a shape to receive a plurality of beam-like electromagnetic waves and output electromagnetic waves by the number different from the number of the received electromagnetic wave beams having a predetermined distribution. Further, at least two of the phase correction mirrors have such a shape to change the phase of the electromagnetic waves beams incident to the reflection surface of the phase correction mirrors by a predetermined amount corresponding to the position of the reflection surface. Then, the cost for transmission system can greatly be reduced. (I.S.)

CR1Dmod: A Matlab program to model 1D complex resistivity effects in electrical and electromagnetic surveys

DEFF Research Database (Denmark)

Ingeman-Nielsen, Thomas; Baumgartner, François

2006-01-01

We have constructed a forward modelling code in Matlab, capable of handling several commonly used electrical and electromagnetic methods in a 1D environment. We review the implemented electromagnetic field equations for grounded wires, frequency and transient soundings and present new solutions...

Airborne radioactive contamination following aerosol ventilation studies

International Nuclear Information System (INIS)

Mackie, A.; Hart, G.C.; Ibbett, D.A.; Whitehead, R.J.S.

1994-01-01

Lung aerosol ventilation studies may be accompanied by airborne contamination, with subsequent surface contamination. Airborne contamination has been measured prior to, during and following 59 consecutive 99 Tc m -diethylenetriamine pentaacetate (DTPA) aerosol studies using a personal air sampler. Airborne contamination ranging between 0 and 20 330 kBq m -3 has been measured. Airborne contamination increases with degree of patient breathing difficulty. The effective dose equivalent (EDE) to staff from ingested activity has been calculated to be 0.3 μSv per study. This figure is supported by data from gamma camera images of a contaminated staff member. However, surface contamination measurements reveal that 60% of studies exceed maximum permissible contamination limits for the hands; 16% of studies exceed limits for controlled area surfaces. (author)

The Effects of Lever Arm (Instrument Offset) Error on GRAV-D Airborne Gravity Data

Science.gov (United States)

Johnson, J. A.; Youngman, M.; Damiani, T.

2017-12-01

High quality airborne gravity collection with a 2-axis, stabilized platform gravity instrument, such as with a Micro-g LaCoste Turnkey Airborne Gravity System (TAGS), is dependent on the aircraft's ability to maintain "straight and level" flight. However, during flight there is constant rotation about the aircraft's center of gravity. Standard practice is to install the scientific equipment close to the aircraft's estimated center of gravity to minimize the relative rotations with aircraft motion. However, there remain small offsets between the instruments. These distance offsets, the lever arm, are used to define the rigid-body, spatial relationship between the IMU, GPS antenna, and airborne gravimeter within the aircraft body frame. The Gravity for the Redefinition of the American Vertical Datum (GRAV-D) project, which is collecting airborne gravity data across the U.S., uses a commercial software package for coupled IMU-GNSS aircraft positioning. This software incorporates a lever arm correction to calculate a precise position for the airborne gravimeter. The positioning software must do a coordinate transformation to relate each epoch of the coupled GNSS-IMU derived position to the position of the gravimeter within the constantly-rotating aircraft. This transformation requires three inputs: accurate IMU-measured aircraft rotations, GNSS positions, and lever arm distances between instruments. Previous studies show that correcting for the lever arm distances improves gravity results, but no sensitivity tests have been done to investigate how error in the lever arm distances affects the final airborne gravity products. This research investigates the effects of lever arm measurement error on airborne gravity data. GRAV-D lever arms are nominally measured to the cm-level using surveying equipment. "Truth" data sets will be created by processing GRAV-D flight lines with both relatively small lever arms and large lever arms. Then negative and positive incremental

Monitoring individual tree-based change with airborne lidar.

Science.gov (United States)

Duncanson, Laura; Dubayah, Ralph

2018-05-01

Understanding the carbon flux of forests is critical for constraining the global carbon cycle and managing forests to mitigate climate change. Monitoring forest growth and mortality rates is critical to this effort, but has been limited in the past, with estimates relying primarily on field surveys. Advances in remote sensing enable the potential to monitor tree growth and mortality across landscapes. This work presents an approach to measure tree growth and loss using multidate lidar campaigns in a high-biomass forest in California, USA. Individual tree crowns were delineated in 2008 and again in 2013 using a 3D crown segmentation algorithm, with derived heights and crown radii extracted and used to estimate individual tree aboveground biomass. Tree growth, loss, and aboveground biomass were analyzed with respect to tree height and crown radius. Both tree growth and loss rates decrease with increasing tree height, following the expectation that trees slow in growth rate as they age. Additionally, our aboveground biomass analysis suggests that, while the system is a net source of aboveground carbon, these carbon dynamics are governed by size class with the largest sources coming from the loss of a relatively small number of large individuals. This study demonstrates that monitoring individual tree-based growth and loss can be conducted with multidate airborne lidar, but these methods remain relatively immature. Disparities between lidar acquisitions were particularly difficult to overcome and decreased the sample of trees analyzed for growth rate in this study to 21% of the full number of delineated crowns. However, this study illuminates the potential of airborne remote sensing for ecologically meaningful forest monitoring at an individual tree level. As methods continue to improve, airborne multidate lidar will enable a richer understanding of the drivers of tree growth, loss, and aboveground carbon flux.

CALIOPE airborne CO{sub 2} DIAL (CACDI) system design

Energy Technology Data Exchange (ETDEWEB)

Mietz, D.; Archuleta, B.; Archuleta, J. [and others

1997-09-01

Los Alamos National Laboratory is currently developing an airborne CO{sub 2} Differential Absorption Lidar (DIAL) system based on second generation technology demonstrated last summer at NTS. The CALIOPE Airborne CO{sub 2} DIAL (CACDI) system requirements have been compiled based on the mission objectives and SONDIAL model trade studies. Subsystem designs have been developed based on flow down from these system requirements, as well as experience gained from second generation ground tests and N-ABLE (Non-proliferation AirBorne Lidar Experiments) airborne experiments. This paper presents the CACDI mission objectives, system requirements, the current subsystem design, and provides an overview of the airborne experimental plan.

Challenges and opportunities of airborne metagenomics.

Science.gov (United States)

Behzad, Hayedeh; Gojobori, Takashi; Mineta, Katsuhiko

2015-05-06

Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles. © The Author(s) 2015. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

Topological Foundations of Electromagnetism

CERN Document Server

Barrett, Terrence W

2008-01-01

Topological Foundations of Electromagnetism seeks a fundamental understanding of the dynamics of electromagnetism; and marshals the evidence that in certain precisely defined topological conditions, electromagnetic theory (Maxwell's theory) must be extended or generalized in order to provide an explanation and understanding of, until now, unusual electromagnetic phenomena. Key to this generalization is an understanding of the circumstances under which the so-called A potential fields have physical effects. Basic to the approach taken is that the topological composition of electromagnetic field

Electromagnetic shaft seal

International Nuclear Information System (INIS)

Takahashi, Kenji.

1994-01-01

As an electromagnetic shaft seal, there are disposed outwarding electromagnetic induction devices having generating power directing to an electroconductive fluid as an object of sealing, and inwarding electromagnetic induction device added coaxially. There are disposed elongate rectangular looped first coils having a predetermined inner diameter, second coils having the same shape and shifted by a predetermined pitch relative to the first coil and third coil having the same shape and shifted by a predetermined pitch relative to the second coil respectively each at a predetermined inner diameter of clearance to the outwarding electromagnetic induction devices and the inwarding electromagnetic induction device. If the inwarding electromagnetic induction device and the outwarding electromagnetic induction device are operated, they are stopped at a point that the generating power of the former is equal with the sum of the generating power of the latter and a differential pressure. When three-phase AC is charged to the first coil, the second coil and the third coil successively, a force is generated in the advancing direction of the magnetic field in the electroconductive fluid by the similar effect to that of a linear motor, and the seal is maintained at high reliability. Moreover, the limit for the rotational angle of the shaft is not caused. (N.H.)

Airborne Evaluation Facility

Data.gov (United States)

Federal Laboratory Consortium — AFRL's Airborne Evaluation Facility (AEF) utilizes Air Force Aero Club resources to conduct test and evaluation of a variety of equipment and concepts. Twin engine...

Structure of the Karoo-age Ellisras Basin in Limpopo Province, South Africa in the light of new airborne geophysical data

CSIR Research Space (South Africa)

Fourie, CJS

2009-09-01

Full Text Available The Waterberg Coalfield is destined to become the major source of energy for South Africa in the future. In 2008, Coaltech Research Organisation funded an airborne magnetic and radiometric survey over the Karoo-age Ellisras Basin in which...

Predictors of Airborne Endotoxin Concentrations in Inner City Homes

Science.gov (United States)

Mazique, D; Diette, GB; Breysse, PN; Matsui, EC; McCormack, MC; Curtin-Brosnan, J; Williams, D; Peng, RD; Hansel, NN

2011-01-01

Few studies have assessed in-home factors which contribute to airborne endotoxin concentrations. In 85 inner-city Baltimore homes, we found no significant correlation between settled dust and airborne endotoxin concentrations. Certain household activities and characteristics, including frequency of dusting, air conditioner use and type of flooring, explained 36–42% of the variability of airborne concentrations. Measurements of both airborne and settled dust endotoxin concentrations may be needed to fully characterize domestic exposure in epidemiologic investigations. PMID:21429483

Helicopter-borne geophysical survey over the areas struck by the tsunami of March 11, 2011, in northeast Japan

Science.gov (United States)

Okuma, S.; Ueda, T.; Mitsuhata, Y.; Uchida, T.

2012-12-01

observed electromagnetic data were processed and apparent resistivity maps were preliminary created for each frequencies. As for the apparent resistivity map at a frequency of 140,000Hz, very low resistivities less than 2 ohm-m are dominant over lagoons and river mouths along the coastline, indicating the existence of salt water wedge. Relatively low resistivities (8 - 22 ohm-m) range from close to the coastline up to 4km inland and are edged to the west by high resistivities (64 - 128 ohm-m), corresponding to the maximum flooded area as derived from aerial photos by the Geospatial Information Authority of Japan (2011). These low resistivities might be associated with the distribution of tsunami deposits with high salinity concentration. As the frequency becomes lower, low resistivities areas (< 8 ohm-m) extend to inland, indicating the existence of deep salt water wedges and/or fossil salt water. Further analyses such as a 1D inversion are being conducted and their results will be given at the presentation. Time-domain EM and high-density electrical surveys are also planned to be conducted on ground to verify the results by airborne surveys.

Sharp spatially constrained inversion

DEFF Research Database (Denmark)

Vignoli, Giulio G.; Fiandaca, Gianluca G.; Christiansen, Anders Vest C A.V.C.

2013-01-01

We present sharp reconstruction of multi-layer models using a spatially constrained inversion with minimum gradient support regularization. In particular, its application to airborne electromagnetic data is discussed. Airborne surveys produce extremely large datasets, traditionally inverted...... by using smoothly varying 1D models. Smoothness is a result of the regularization constraints applied to address the inversion ill-posedness. The standard Occam-type regularized multi-layer inversion produces results where boundaries between layers are smeared. The sharp regularization overcomes...... inversions are compared against classical smooth results and available boreholes. With the focusing approach, the obtained blocky results agree with the underlying geology and allow for easier interpretation by the end-user....

Aerial radiometric and magnetic survey: Bozeman National Topographic Map, Montana

International Nuclear Information System (INIS)

1979-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Bozeman National Topographic Map NL12-8 are presented in Volume I and II of this report. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium, and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

14 CFR 135.175 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne weather...

14 CFR 135.173 - Airborne thunderstorm detection equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne thunderstorm detection equipment... Aircraft and Equipment § 135.173 Airborne thunderstorm detection equipment requirements. (a) No person may... the aircraft is equipped with either approved thunderstorm detection equipment or approved airborne...

Towards airborne nanoparticle mass spectrometry with nanomechanical string resonators

DEFF Research Database (Denmark)

Schmid, Silvan; Kurek, Maksymilian; Boisen, Anja

2013-01-01

airborne nanoparticle sensors. Recently, nanomechanical mass spectrometry was established. One of the biggest challenges of nanomechanical sensors is the low efficiency of diffusion-based sampling. We developed an inertial-based sampling method that enables the efficient sampling of airborne nanoparticles...... mode. Mass spectrometry of airborne nanoparticles requires the simultaneous operation in the first and second mode, which can be implemented in the transduction scheme of the resonator. The presented results lay the cornerstone for the realization of a portable airborne nanoparticle mass spectrometer....

Utilizing experimentally derived multi-channel gamma-ray spectra for the analysis of airborne data

International Nuclear Information System (INIS)

Grasty, R.L.

1982-01-01

Gamma-ray spectra derived from measurements on radioactive concrete calibration pads using plywood sheets to simulate the attenuation effect of air have been successfully tested on airbone data. Cesium-137 at 662 keV, from atomic weapons tests was found to contribute significantly to the airborne spectrum. By fitting the experimental spectra, above the cesium energy, to airborne data, significant increases in accuracy were obtained for the measurement of uranium and thorium, compared to the standard 3-window method. By including a cesium spectrum is the analysis of gamma-ray data from a survey carried out in Saskatchewan, it was found that background radiation due to atmospheric bismuth-214 could be measured more reliably than by using a constant over-water background. Similar results were obtained by monitoring low energy lead-214 gamma-rays at 352 keV

Aerial radiometric and magnetic survey national topographic map: Sonora, Texas. Final report

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Sonora National Topographic Map NH14-4 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: Burlington National Topographic Map, Illinois/Iowa/Missouri

International Nuclear Information System (INIS)

1981-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Burlington National Topographic Map NK15-12 is presented in this report. The airborne data gathered is reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Phase Center Interpolation Algorithm for Airborne GPS through the Kalman Filter

Directory of Open Access Journals (Sweden)

Edson A. Mitishita

2005-12-01

Full Text Available The aerial triangulation is a fundamental step in any photogrammetric project. The surveying of the traditional control points, depending on region to be mapped, still has a high cost. The distribution of control points at the block, and its positional quality, influence directly in the resulting precisions of the aero triangulation processing. The airborne GPS technique has as key objectives cost reduction and quality improvement of the ground control in the modern photogrammetric projects. Nowadays, in Brazil, the greatest photogrammetric companies are acquiring airborne GPS systems, but those systems are usually presenting difficulties in the operation, due to the need of human resources for the operation, because of the high technology involved. Inside the airborne GPS technique, one of the fundamental steps is the interpolation of the position of the phase center of the GPS antenna, in the photo shot instant. Traditionally, low degree polynomials are used, but recent studies show that those polynomials is reduced in turbulent flights, which are quite common, mainly in great scales flights. This paper has as objective to present a solution for that problem, through an algorithm based on the Kalman Filter, which takes into account the dynamic aspect of the problem. At the end of the paper, the results of a comparison between experiments done with the proposed methodology and a common linear interpolator are shown. These results show a significant accuracy gain at the procedure of linear interpolation, when the Kalman filter is used.

Current glimpse of airborne allergenic pollen in Indian subcontinent

Directory of Open Access Journals (Sweden)

Kavita Ghosal

2015-12-01

Full Text Available Respiratory allergic diseases such as bronchial asthma, rhinitis, urticaria, atopic dermatitis have been steadily increasing all over the world, including India. Owing to its alarming trend, several aerobiological surveys have been undertaken in different parts of India to delineate the variety of pollen and spore load. In this review, we have reported the current state of aerobiological knowladge in India with particular reference to allergenic airborn pollen occurence in 2001–2015. Pollen have been found to contribute a significant proportion in the air and caused allergy symptoms in the local inhabitants. Aerobiological records, a questionnaire survey and hospitalization records have been employed for the analysis. Holoptelea integrifolia, Amaranthus spinosus in northern region, Sorghum vulgare, Pennisetum, Gynandropsis gynandra, Parthenium hysterophorus, Dolichandrone platycalyx in southern regions, and Parthenium hysterophorus from the western region; Cynodon dactylon, Cenchrus ciliaris in the central area; Acacia auriculiformis, Cleome gynandra, Catharanthus roseus, Phoenix sylvestris, Areca catechu, and Lantana camara in the eastern regions as potential aeroallergens in India. The statistical approach confirmed the correlation between hospitalization rate associated with allergy-related health troubles and the prevalent allergenic pollen in the air. The Poaceae group has been found to be dominant throughout India. Immuno-biochemical studies identified various protein with allergenic potential found in the pollen recorded. Epitope identification and homology of the major allergenic protein Cat r1 of Catharanthus sp and Par j 1 of Parietaria judaica have been found. Identification of allergenic pollen grains and the modern approach concerning cross-reactivity and epitope revelation of dominant airborne pollen have important clinical implications for the prevention, diagnosis and treatments of allergic diseases in India.

14 CFR 125.223 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather radar...

14 CFR 121.357 - Airborne weather radar equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane. (b...

Applied Electromagnetics

Energy Technology Data Exchange (ETDEWEB)

Yamashita, H; Marinova, I; Cingoski, V [eds.

2002-07-01

These proceedings contain papers relating to the 3rd Japanese-Bulgarian-Macedonian Joint Seminar on Applied Electromagnetics. Included are the following groups: Numerical Methods I; Electrical and Mechanical System Analysis and Simulations; Inverse Problems and Optimizations; Software Methodology; Numerical Methods II; Applied Electromagnetics.

Applied Electromagnetics

International Nuclear Information System (INIS)

Yamashita, H.; Marinova, I.; Cingoski, V.

2002-01-01

These proceedings contain papers relating to the 3rd Japanese-Bulgarian-Macedonian Joint Seminar on Applied Electromagnetics. Included are the following groups: Numerical Methods I; Electrical and Mechanical System Analysis and Simulations; Inverse Problems and Optimizations; Software Methodology; Numerical Methods II; Applied Electromagnetics

Electromagnetic shield

International Nuclear Information System (INIS)

Miller, J.S.

1987-01-01

An electromagnetic shield is described comprising: closed, electrically-conductive rings, each having an open center; and binder means for arranging the rings in a predetermined, fixed relationship relative to each other, the so-arranged rings and binder means defining an outer surface; wherein electromagnetic energy received by the shield from a source adjacent its outer surface induces an electrical current to flow in a predetermined direction adjacent and parallel to the outer surface, through the rings; and wherein each ring is configured to cause source-induced alternating current flowing through the portion of the ring closest to the outer surface to electromagnetically induce an oppositely-directed current in the portion of the ring furthest from the surface, such oppositely-directed current bucking any source-induced current in the latter ring portion and thus reducing the magnitude of current flowing through it, whereby the electromagnetic shielding effected by the shield is enhanced

Engineering electromagnetics

CERN Document Server

Thomas, David T; Hartnett, James P; Hughes, William F

1973-01-01

The applications involving electromagnetic fields are so pervasive that it is difficult to estimate their contribution to the industrial output: generation of electricity, power transmission lines, electric motors, actuators, relays, radio, TV and microwave transmission and reception, magnetic storage, and even the mundane little magnet used to hold a paper note on the refrigerator are all electromagnetic in nature. One would be hard pressed to find a device that works without relaying on any electromagnetic principle or effect. This text provides a good theoretical understanding of the electromagnetic field equations but also treats a large number of applications. In fact, no topic is presented unless it is directly applicable to engineering design or unless it is needed for the understanding of another topic. In electrostatics, for example, the text includes discussions of photocopying, ink-jet printing, electrostatic separation and deposition, sandpaper production, paint spraying, and powder coating. In ma...

Self-Organizing Maps: A Data Mining Tool for the Analysis of Airborne Geophysical Data Collected over the Brazilian Amazon

Science.gov (United States)

Carneiro, C.; Fraser, S. J.; Crosta, A. P.; Silva, A.; Barros, C.

2011-12-01

Regional airborne geophysical data sets are being collected worldwide to promote mineral exploration and resource development. These data sets often are collected over highly prospective terranes, where access is limited or there are environmental concerns. Such regional surveys typically consist of two or more sensor packages being flown in an aircraft over the survey area and vast amounts of near-continuous data can be acquired in a relatively short time. Increasingly, there is also a need to process such data in a timely fashion to demonstrate the data's value and indicate the potential return or value of the survey to the funding agency. To assist in the timely analysis of such regional data sets, we have used an exploratory data mining approach: the Self Organizing Map (SOM). Because SOM is based on vector quantization and measures of vector similarity, it is an ideal tool to analyze a data set consisting of disparate geophysical input parameters to look for relationships and trends. We report on our use of SOM to analyze part of a regional airborne geophysical survey collected over the prospective Anapu-Tuere region of the Brazilian Amazon. Magnetic and spectrometric gamma ray data were used as input to our SOM analysis, and the results used to discriminate and identify various rock types and produce a "pseudo" geological map over the study area. The ability of SOM to define discrete domains of rock-types with similar properties allowed us to expand upon existing geological knowledge of the area for mapping purposes; and, often it was the combination of the magnetic and radiometric responses that identified a lithology's unique response. One particular unit was identified that had an association with known gold mineralization, which consequently highlighted the prospectivity of that unit elsewhere in the survey area. Our results indicate that SOM can be used for the semi-automatic analysis of regional airborne geophysical data to assist in geological mapping

A system for airborne SAR interferometry

DEFF Research Database (Denmark)

Madsen, Søren Nørvang; Skou, Niels; Granholm, Johan

1996-01-01

Interferometric synthetic aperture radar (INSAR) systems have already demonstrated that elevation maps can be generated rapidly with single pass airborne across-track interferometry systems (XTT), and satellite repeat track interferometry (RTT) techniques have been used to map both elevation...... and perturbations of the surface of the Earth. The Danish Center for Remote Sensing (DCRS) has experimented with airborne INSAR since 1993. Multiple track data are collected in a special mode in which the radar directly steers the aircraft which allows for very precise control of the flight path. Such data sets......) the status of the airborne interferometry activities at DCRS, including the present system configuration, recent results, and some scientific applications of the system....

Electromagnetic ultrasonic guided waves

CERN Document Server

Huang, Songling; Li, Weibin; Wang, Qing

2016-01-01

This book introduces the fundamental theory of electromagnetic ultrasonic guided waves, together with its applications. It includes the dispersion characteristics and matching theory of guided waves; the mechanism of production and theoretical model of electromagnetic ultrasonic guided waves; the effect mechanism between guided waves and defects; the simulation method for the entire process of electromagnetic ultrasonic guided wave propagation; electromagnetic ultrasonic thickness measurement; pipeline axial guided wave defect detection; and electromagnetic ultrasonic guided wave detection of gas pipeline cracks. This theory and findings on applications draw on the author’s intensive research over the past eight years. The book can be used for nondestructive testing technology and as an engineering reference work. The specific implementation of the electromagnetic ultrasonic guided wave system presented here will also be of value for other nondestructive test developers.

Evaluation and Comparison of the Processing Methods of Airborne Gravimetry Concerning the Errors Effects on Downward Continuation Results: Case Studies in Louisiana (USA) and the Tibetan Plateau (China).

Science.gov (United States)

Zhao, Qilong; Strykowski, Gabriel; Li, Jiancheng; Pan, Xiong; Xu, Xinyu

2017-05-25

Gravity data gaps in mountainous areas are nowadays often filled in with the data from airborne gravity surveys. Because of the errors caused by the airborne gravimeter sensors, and because of rough flight conditions, such errors cannot be completely eliminated. The precision of the gravity disturbances generated by the airborne gravimetry is around 3-5 mgal. A major obstacle in using airborne gravimetry are the errors caused by the downward continuation. In order to improve the results the external high-accuracy gravity information e.g., from the surface data can be used for high frequency correction, while satellite information can be applying for low frequency correction. Surface data may be used to reduce the systematic errors, while regularization methods can reduce the random errors in downward continuation. Airborne gravity surveys are sometimes conducted in mountainous areas and the most extreme area of the world for this type of survey is the Tibetan Plateau. Since there are no high-accuracy surface gravity data available for this area, the above error minimization method involving the external gravity data cannot be used. We propose a semi-parametric downward continuation method in combination with regularization to suppress the systematic error effect and the random error effect in the Tibetan Plateau; i.e., without the use of the external high-accuracy gravity data. We use a Louisiana airborne gravity dataset from the USA National Oceanic and Atmospheric Administration (NOAA) to demonstrate that the new method works effectively. Furthermore, and for the Tibetan Plateau we show that the numerical experiment is also successfully conducted using the synthetic Earth Gravitational Model 2008 (EGM08)-derived gravity data contaminated with the synthetic errors. The estimated systematic errors generated by the method are close to the simulated values. In addition, we study the relationship between the downward continuation altitudes and the error effect. The

Evaluation and Comparison of the Processing Methods of Airborne Gravimetry Concerning the Errors Effects on Downward Continuation Results: Case Studies in Louisiana (USA) and the Tibetan Plateau (China)

Science.gov (United States)

Zhao, Q.

2017-12-01

Gravity data gaps in mountainous areas are nowadays often filled in with the data from airborne gravity surveys. Because of the errors caused by the airborne gravimeter sensors, and because of rough flight conditions, such errors cannot be completely eliminated. The precision of the gravity disturbances generated by the airborne gravimetry is around 3-5 mgal. A major obstacle in using airborne gravimetry are the errors caused by the downward continuation. In order to improve the results the external high-accuracy gravity information e.g., from the surface data can be used for high frequency correction, while satellite information can be applying for low frequency correction. Surface data may be used to reduce the systematic errors, while regularization methods can reduce the random errors in downward continuation. Airborne gravity surveys are sometimes conducted in mountainous areas and the most extreme area of the world for this type of survey is the Tibetan Plateau. Since there are no high-accuracy surface gravity data available for this area, the above error minimization method involving the external gravity data cannot be used. We propose a semi-parametric downward continuation method in combination with regularization to suppress the systematic error effect and the random error effect in the Tibetan Plateau; i.e., without the use of the external high-accuracy gravity data. We use a Louisiana airborne gravity dataset from the USA National Oceanic and Atmospheric Administration (NOAA) to demonstrate that the new method works effectively. Furthermore, and for the Tibetan Plateau we show that the numerical experiment is also successfully conducted using the synthetic Earth Gravitational Model 2008 (EGM08)-derived gravity data contaminated with the synthetic errors. The estimated systematic errors generated by the method are close to the simulated values. In addition, we study the relationship between the downward continuation altitudes and the error effect. The

Risk perception and public concerns of electromagnetic waves from cellular phones in Korea.

Science.gov (United States)

Kim, Kyunghee; Kim, Hae-Joon; Song, Dae Jong; Cho, Yong Min; Choi, Jae Wook

2014-05-01

In this study, the difference between the risk perception of electromagnetic waves from cellular phones and the risk perception of other factors such as environment and food was analyzed. The cause of the difference in the psychological and social factors that affect the group with high risk perception of electromagnetic waves was also analyzed. A questionnaire survey on the risk perception of electromagnetic waves from cellular phones was carried out on 1001 subjects (men and women) over the age of 20. In the group with high risk perception of electromagnetic waves from cellular phones, women had higher risk perception than men. Logistic regression analysis, where the group with high risk perception of electromagnetic waves and the group with low risk perception were used as dependent variables, indicated that the risk perception of electromagnetic waves in women was 1.815 times statistically significantly higher than the risk perception of men (95% CI: 1.340-2.457). Also, high risk perception of electromagnetic waves from cellular phones was observed when the subjects considered that they had more personal knowledge (OR: 1.416, 95% CI: 1.216-1.648), that the seriousness of the risk to future generations was high (OR: 1.410, 95% CI: 1.234-1.611), and their outrage for the occurrence of accidents related to electromagnetic waves was high (OR: 1.460, 95% CI: 1.264-1.686). The results of this study need to be sufficiently considered and reflected in designing the risk communication strategies and communication methods for the preventive measures and advice on electromagnetic waves from cellular phones. © 2014 Wiley Periodicals, Inc.

Airborne asbestos fibre levels in buildings: a summary of UK measurements.

Science.gov (United States)

Burdett, G J; Jaffrey, S A; Rood, A P

1989-01-01

The UK Health and Safety Executive, in conjunction with the Department of the Environment, has carried out a number of surveys of airborne asbestos fibre concentrations in buildings. All samples have been collected on membrane filters and analysed by analytical transmission electron microscopy. Four categories of buildings under normal occupation have been investigated; non-domestic buildings containing sprayed or trowelled asbestos, domestic buildings containing sprayed asbestos or asbestos plaster, buildings with warm air heaters containing asbestos and buildings without asbestos materials. A number of buildings have also been surveyed during and after the removal of asbestos materials. The choice of measurement indices and analytical procedures is reviewed, before measurements are compared in terms of the concentration of asbestos fibres greater than 5 microns long. The decision whether to remove asbestos from occupied buildings is discussed with reference to the associated cost and risk. In the present survey, management of undamaged asbestos appeared preferable to large-scale removal.

Airborne gamma ray measurements conducted during an international trial in Finland

Energy Technology Data Exchange (ETDEWEB)

Sanderson, D.C.W.; Allyson, J.D.; McConville, P.; Murphy, S.; Smith, J. [Scottish Univ. Research and Reactor Centre, Glasgow, Scotland (United Kingdom)

1997-12-31

The Scottish Universities Research and Reactor Centre (SURRC) contributed to the Resume 95 exercise by developing the calibration site at Vesivehmaa, and by participating in the airborne gamma spectrometry (AGS) part of the study. This paper summarises the airborne survey results from the SURRC team. The AGS tasks included fallout mapping of a 6x3 km area in central Finland with nominal 150 m line spacing, and a time constrained search for an undisclosed number of hidden radioactive sources. Measurements at the calibration site were also taken to provide a basis for traceable cross comparison between each teams` quantification procedures at a single, well characterised, location. A full set of calibrated maps of Chernobyl deposition and natural radionuclides, together with overlays corresponding to topography, roads, rivers and lakes were finished during the survey and displayed at the end of the exercise. The main survey area (Area II) was found to have a mean {sup 137}Cs deposition of 64.4{+-}24.4 kBq m{sup -2}, based on the calibration appropriate to the Vesivehmaa site. The major point sources in Area III were discovered, although the collimated {sup 137}Cs and {sup 60}Co sources were not. Retrospective analysis has shown that sources Cs3 and Cs4 were not significantly above local environmental levels in our data set; whereas the low activity {sup 60}Co source Co3 was detected. This confirms the improved sensitivity of AGS source searches to nuclides which are not already present as environmental contaminants. The collimated {sup 192}Ir was found both using scattered radiation and from full energy lines detected with a Ge detector. The {sup 99m}Tc was located using a ratio of low energy integrals from the NaI spectra. (EG). 28 refs.

Airborne gamma ray measurements conducted during an international trial in Finland

International Nuclear Information System (INIS)

Sanderson, D.C.W.; Allyson, J.D.; McConville, P.; Murphy, S.; Smith, J.

1997-01-01

The Scottish Universities Research and Reactor Centre (SURRC) contributed to the Resume 95 exercise by developing the calibration site at Vesivehmaa, and by participating in the airborne gamma spectrometry (AGS) part of the study. This paper summarises the airborne survey results from the SURRC team. The AGS tasks included fallout mapping of a 6x3 km area in central Finland with nominal 150 m line spacing, and a time constrained search for an undisclosed number of hidden radioactive sources. Measurements at the calibration site were also taken to provide a basis for traceable cross comparison between each teams' quantification procedures at a single, well characterised, location. A full set of calibrated maps of Chernobyl deposition and natural radionuclides, together with overlays corresponding to topography, roads, rivers and lakes were finished during the survey and displayed at the end of the exercise. The main survey area (Area II) was found to have a mean 137 Cs deposition of 64.4±24.4 kBq m -2 , based on the calibration appropriate to the Vesivehmaa site. The major point sources in Area III were discovered, although the collimated 137 Cs and 60 Co sources were not. Retrospective analysis has shown that sources Cs3 and Cs4 were not significantly above local environmental levels in our data set; whereas the low activity 60 Co source Co3 was detected. This confirms the improved sensitivity of AGS source searches to nuclides which are not already present as environmental contaminants. The collimated 192 Ir was found both using scattered radiation and from full energy lines detected with a Ge detector. The 99m Tc was located using a ratio of low energy integrals from the NaI spectra. (EG)

Airborne gamma ray measurements conducted during an international trial in Finland

Energy Technology Data Exchange (ETDEWEB)

Sanderson, D C.W.; Allyson, J D; McConville, P; Murphy, S; Smith, J [Scottish Univ. Research and Reactor Centre, Glasgow, Scotland (United Kingdom)

1998-12-31

The Scottish Universities Research and Reactor Centre (SURRC) contributed to the Resume 95 exercise by developing the calibration site at Vesivehmaa, and by participating in the airborne gamma spectrometry (AGS) part of the study. This paper summarises the airborne survey results from the SURRC team. The AGS tasks included fallout mapping of a 6x3 km area in central Finland with nominal 150 m line spacing, and a time constrained search for an undisclosed number of hidden radioactive sources. Measurements at the calibration site were also taken to provide a basis for traceable cross comparison between each teams` quantification procedures at a single, well characterised, location. A full set of calibrated maps of Chernobyl deposition and natural radionuclides, together with overlays corresponding to topography, roads, rivers and lakes were finished during the survey and displayed at the end of the exercise. The main survey area (Area II) was found to have a mean {sup 137}Cs deposition of 64.4{+-}24.4 kBq m{sup -2}, based on the calibration appropriate to the Vesivehmaa site. The major point sources in Area III were discovered, although the collimated {sup 137}Cs and {sup 60}Co sources were not. Retrospective analysis has shown that sources Cs3 and Cs4 were not significantly above local environmental levels in our data set; whereas the low activity {sup 60}Co source Co3 was detected. This confirms the improved sensitivity of AGS source searches to nuclides which are not already present as environmental contaminants. The collimated {sup 192}Ir was found both using scattered radiation and from full energy lines detected with a Ge detector. The {sup 99m}Tc was located using a ratio of low energy integrals from the NaI spectra. (EG). 28 refs.

[Relationships between air conditioning, airborne microorganisms and health].

Science.gov (United States)

Parat, S; Perdrix, A; Baconnier, P

1999-01-01

Concurrently with the increase of air-conditioning, potentially severe or frequent new diseases have emerged, giving rise to social and economical consequences. The first part of this work is a state of the art review of the relationships between air-conditioning, airborne microorganisms and health, through a technical, metrological and medical approach. The second part presents four studies performed in this field. Two of them deal with the relationship between airborne microorganisms and technical features of air-conditioning. Measurements performed on actual sites demonstrated the benefit of using high efficiency filters and low risk components in air-conditioning systems. The third study was aimed to look for a relationship between airborne microorganisms and sick building syndrome symptoms. Statistical analyses of individual data revealed significant associations between airborne bacteria or fungi and symptoms. These results may be the first step in determining a dose-response relationship, in order to define threshold limit values in this field. In the fourth study, the contribution of particle counting in assessing exposure to airborne microorganisms was explored by monitoring simultaneous variations of microbial and particle concentrations. The results showed that associating particle counting may allow to detect microbial variations instantaneously, and therefore improve the assessment of exposure to airborne microorganisms.

Characterisation of particulate matter on airborne pollen grains

International Nuclear Information System (INIS)

Ribeiro, Helena; Guimarães, Fernanda; Duque, Laura; Noronha, Fernando; Abreu, Ilda

2015-01-01

A characterization of the physical–chemical composition of the atmospheric PM adsorbed to airborne pollen was performed. Airborne pollen was sampled using a Hirst-type volumetric spore sampler and observed using a Field Emission Electron Probe Microanalyser for PM analysis. A secondary electron image was taken of each pollen grain and EDS spectra were obtained for individually adsorbed particles. All images were analysed and the size parameters of the particles adsorbed to pollen was determined. The measured particles’ equivalent diameter varied between 0.1 and 25.8 μm, mostly in the fine fraction. The dominant particulates identified were Si-rich, Organic-rich, SO-rich, Metals & Oxides and Cl-rich. Significant daily differences were observed in the physical–chemical characteristics of particles adsorbed to the airborne pollen wall. These differences were correlated with weather parameters and atmospheric PM concentration. Airborne pollen has the ability to adsorb fine particles that may enhance its allergenicity. - Highlights: • Airborne pollen sorbs other PM found in suspension. • 84% of the particles sorbed belonged to the fine aerosol fraction. • Adsorbed PM presented daily physical–chemical variations. • Particles sorbed dominated by Si-rich, Organic-rich, SO-rich, Fe-rich and Cl-rich. - Airborne pollen is able to transport finer particulate matter, which presents daily physical–chemical variations.

Radioactive Contamination Estimation from micro-copters or helicopter Airborne survey: Simulation and real measurements

International Nuclear Information System (INIS)

Halevy, I.; Ghelman, M.; Yehuda-Zada, Y.; Manor, A.; Dadon, S.; Sharon, A.; Yaar, I.

2014-01-01

One of the main advantages of acquiring aero-radiometric measurements lies in the high collection rate of data over large areas and rough terrain. Typical aero-radiometric system records and saves gamma ray spectrum, correlated with the GPS derived location information in regular time intervals of one to two seconds. Such data can be used to locate radiation anomalies on the ground, map ground contamination or track a radioactive airborne plume. Acquiring spectral data of this type allows separation of natural radioactivity from that of man-made sources and identification of specific isotopes, natural or man-made

Radioactive Contamination Estimation from Micro-Copters or Helicopter Airborne Survey: Simulation and Real Measurements

International Nuclear Information System (INIS)

Halevy, I.; Ghelman, M.; Yehuda-Zada, Y.; Manor, A.; Sharon, A.; Yaar, I.

2014-01-01

One of the main advantages of acquiring aero-radiometric measurements lies in the high collection rate of data over large areas and rough terrain. Typical aero-radiometric system records and saves gamma ray spectrum, correlated with the GPS derived location information in regular time intervals of one to two seconds. Such data can be used to locate radiation anomalies on the ground, map ground contamination or track a radioactive airborne plume. Acquiring spectral data of this type allows separation of natural radioactivity from that of man-made sources and identification of specific isotopes, natural or man-made

30 CFR 57.5001 - Exposure limits for airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure limits for airborne contaminants. 57... Underground § 57.5001 Exposure limits for airborne contaminants. Except as permitted by § 57.5005— (a) Except as provided in paragraph (b), the exposure to airborne contaminants shall not exceed, on the basis of...

Characterization of airborne uranium from test firing of XM774 ammunition

International Nuclear Information System (INIS)

Glissmeyer, J.A.; Mishima, J.

1979-11-01

Pacific Northwest Laboratory conducted experiments at Aberdeen Proving Grounds, Maryland, to characterize the airborne depleted uranium (DU) resulting from the test firings of 105-mm, APFSDS-T XM774 ammunition. The goal was to obtain data pertinent to evaluations of human inhalation exposure to the airborne DU. Data was desired concerning the following: (1) size distribution of airborne DU; (2) quantity of airborne DU; (3) dispersion of airborne DU from the target vicinity; (4) amount of DU deposited on the ground; (5) solubility of airborne DU compounds in lung fluid; and (6) oxide forms of airborne and fallout DU. The experiments involved extensive air sampling for total airborne DU particulates and respirable DU particles both above the targets and at distances downwind. Fallout and fragments were collected around the target area. High-speed movies of the smoke generated from the impact of the penetrators were taken to estimate the cloud volumes. Results of the experiments are presented

Model for Electromagnetic Information Leakage

OpenAIRE

Mao Jian; Li Yongmei; Zhang Jiemin; Liu Jinming

2013-01-01

Electromagnetic leakage will happen in working information equipments; it could lead to information leakage. In order to discover the nature of information in electromagnetic leakage, this paper combined electromagnetic theory with information theory as an innovative research method. It outlines a systematic model of electromagnetic information leakage, which theoretically describes the process of information leakage, intercept and reproduction based on electromagnetic radiation, and ana...

Resolution analyses for selecting an appropriate airborne electromagnetic (AEM) system

DEFF Research Database (Denmark)

Christensen, N.B.; Lawrie, Ken

2012-01-01

is necessary and has to be approached in a pragmatic way involving a range of different aspects. In this paper, we concentrate on the resolution analysis perspective and demonstrate that the inversion analysis must be preferred over the derivative analysis because it takes parameter coupling into account, and...... resolution for a series of models relevant to the survey area by comparing the sum over the data of squares of noise-normalised derivatives. We compare this analysis method with a resolution analysis based on the posterior covariance matrix of an inversion formulation. Both of the above analyses depend......, furthermore, that the derivative analysis generally overestimates the resolution capability. Finally we show that impulse response data are to be preferred over step response data for near-surface resolution....

Airborne Nicotine, Secondhand Smoke, and Precursors to Adolescent Smoking.

Science.gov (United States)

McGrath, Jennifer J; Racicot, Simon; Okoli, Chizimuzo T C; Hammond, S Katharine; O'Loughlin, Jennifer

2018-01-01

Secondhand smoke (SHS) directly increases exposure to airborne nicotine, tobacco's main psychoactive substance. When exposed to SHS, nonsmokers inhale 60% to 80% of airborne nicotine, absorb concentrations similar to those absorbed by smokers, and display high levels of nicotine biomarkers. Social modeling, or observing other smokers, is a well-established predictor of smoking during adolescence. Observing smokers also leads to increased pharmacological exposure to airborne nicotine via SHS. The objective of this study is to investigate whether greater exposure to airborne nicotine via SHS increases the risk for smoking initiation precursors among never-smoking adolescents. Secondary students ( N = 406; never-smokers: n = 338, 53% girls, mean age = 12.9, SD = 0.4) participated in the AdoQuest II longitudinal cohort. They answered questionnaires about social exposure to smoking (parents, siblings, peers) and known smoking precursors (eg, expected benefits and/or costs, SHS aversion, smoking susceptibility, and nicotine dependence symptoms). Saliva and hair samples were collected to derive biomarkers of cotinine and nicotine. Adolescents wore a passive monitor for 1 week to measure airborne nicotine. Higher airborne nicotine was significantly associated with greater expected benefits ( R 2 = 0.024) and lower expected costs ( R 2 = 0.014). Higher social exposure was significantly associated with more temptation to try smoking ( R 2 = 0.025), lower aversion to SHS ( R 2 = 0.038), and greater smoking susceptibility ( R 2 = 0.071). Greater social exposure was significantly associated with more nicotine dependence symptoms; this relation worsened with higher nicotine exposure (cotinine R 2 = 0.096; airborne nicotine R 2 = 0.088). Airborne nicotine exposure via SHS is a plausible risk factor for smoking initiation during adolescence. Public health implications include limiting airborne nicotine through smoking bans in homes and cars, in addition to stringent restrictions

Research on the electromagnetic structure of movable coil electromagnet drive mechanism for reactor control rod

International Nuclear Information System (INIS)

Zhang Jige; Yian Huijie; Wu Yuanqiang; Wu Xinxin; Yu Suyuan; He Shuyan

2007-01-01

The movable coil electromagnet drive mechanism (MCEDM) is a new drive scheme for the reactor control rod, and it has a simple structure, good security and reliability property, etc. MCEDM with an air cooled structure has been used in the land research reactor. In order to apply MCEDM to the mobile reactor, experimental and theoretical study on the electromagnet with an oil-water cooled structure and a single magnetic flux circuit (called the type A electro-magnet) has been completed. It is proven by the experiment and theory that the oil-water cooled structure is an excellent measure to increase the coil current of MCEDM. Moreover, a type B electromagnet with an oil-water cooled structure and double magnetic flux circuits is designed to further increase the magnetic force of MCEDM. The analysis of finite element method shows that the type B electromagnet could double the saturation current of type A electro-magnet and the magnetic force of type B electromagnet is greater than that of the type A electromagnet. Moreover, it is proven that the dynamic property of type B electromagnet is better than type A electromagnet. (author)

The relationships between air pollutants, meteorological parameters and concentration of airborne fungal spores

International Nuclear Information System (INIS)

Grinn-Gofron, Agnieszka; Strzelczak, Agnieszka; Wolski, Tomasz

2011-01-01

Fungal spores are an important component of bioaerosol and also considered to act as indicator of the level of atmospheric bio-pollution. Therefore, better understanding of these phenomena demands a detailed survey of airborne particles. The objective of this study was to examine the dependence of two the most important allergenic taxa of airborne fungi - Alternaria and Cladosporium - on meteorological parameters and air pollutant concentrations during three consecutive years (2006-2008). This study is also an attempt to create artificial neural network (ANN) forecasting models useful in the prediction of aeroallergen abundance. There were statistically significant relationships between spore concentration and environmental parameters as well as pollutants, confirmed by the Spearman's correlation rank analysis and high performance of the ANN models obtained. The concentrations of Cladosporium and Alternaria spores can be predicted with quite good accuracy from meteorological conditions and air pollution recorded three days earlier. - ANN models predict airspore contents from weather conditions and air pollutant.

Aerial radiometric and magnetic survey: Woodward National Topographic Map, Oklahoma, West Texas project

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Woodward National Topographic Map NJ14-11 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: Winchester National topographic map, Kentucky. Southeast US project

International Nuclear Information System (INIS)

1980-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Winchester National Topographic Map NJ16-9 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: San Antonio National Topographic Map, Texas. Final report

International Nuclear Information System (INIS)

1980-05-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the San Antonio National Topographic Map NH14-8 are presented. The airborne data gathered are reduced by ground computer facilities to yield profile plots of the basic uranium, thorium, and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnetic field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Aerial radiometric and magnetic survey: Quincy National Topographic map, Illinois/Missouri. Final report

International Nuclear Information System (INIS)

1981-01-01

The results of analyses of the airborne gamma radiation and total magnetic field survey flown for the region identified as the Quincy National Topographic Map NJ15-3 is presented in this report. The airborne data gathered is reduced by ground computer facilities to yield profile plots of the basic uranium, thorium and potassium equivalent gamma radiation intensities, ratios of these intensities, aircraft altitude above the earth's surface, total gamma ray and earth's magnet field intensity, correlated as a function of geologic units. The distribution of data within each geologic unit, for all surveyed map lines and tie lines, has been calculated and is included. Two sets of profiled data for each line are included, with one set displaying the above-cited data. The second set includes only flight line magnetic field, temperature, pressure, altitude data plus magnetic field data as measured at a base station. A general description of the area, including descriptions of the various geologic units and the corresponding airborne data, is included also

Electromagnetic properties for arbitrary spin particles: Natural electromagnetic moments from light-cone arguments

International Nuclear Information System (INIS)

Lorce, Cedric

2009-01-01

We revisit the old-standing problem of the electromagnetic interaction for particles of arbitrary spin. Based on the assumption that light-cone helicity at tree level and Q 2 =0 should be conserved nontrivially by the electromagnetic interaction, we are able to derive all the natural electromagnetic moments for a pointlike particle of any spin. We provide here a transparent decomposition of the electromagnetic current in terms of covariant vertex functions. We also define in a general way the electromagnetic multipole form factors, and show their relation with the electromagnetic moments and covariant vertex functions. The light-cone helicity conservation argument determines uniquely the values of all electromagnetic moments, which we refer to as the 'natural' ones. These specific values are in accordance with the standard model, and the prediction of universal g=2 gyromagnetic factor is naturally recovered. We provide a very simple and compact formula for these natural moments. As an application of our results, we generalize the discussion of quark transverse charge densities to particles with arbitrary spin, giving more physical support to the light-cone helicity conservation argument.

Electromagnetic wave matching device

International Nuclear Information System (INIS)

Hirata, Yosuke; Mitsunaka, Yoshika; Hayashi, Ken-ichi; Ito, Yasuyuki.

1997-01-01

The present invention provides a matching device capable of increasing an efficiency of combining beams of electromagnetic waves outputted from an output window of a gyrotron which is expected for plasma heating of a thermonuclear reactor and an electromagnetic wave transmission system as high as possible. Namely, an electromagnetic wave matching device reflects beams of electromagnetic waves incident from an inlet by a plurality of phase correction mirrors and combines them to an external transmission system through an exit. In this case, the phase correction mirrors change the phase of the beams of electromagnetic waves incident to the phase correction mirrors by a predetermined amount corresponding to the position of the reflection mirrors. Then, the beams of electromagnetic waves outputted, for example, from a gyrotron can properly be shaped as desired for the intensity and the phase. As a result, combination efficiency with the transmission system can be increased. (I.S.)

Basic Electromagnetism and Materials

CERN Document Server

Moliton, André

2007-01-01

Basic Electromagnetism and Materials is the product of many years of teaching basic and applied electromagnetism. This textbook can be used to teach electromagnetism to a wide range of undergraduate science majors in physics, electrical engineering or materials science. However, by making lesser demands on mathematical knowledge than competing texts, and by emphasizing electromagnetic properties of materials and their applications, this textbook is uniquely suited to students of materials science. Many competing texts focus on the study of propagation waves either in the microwave or optical domain, whereas Basic Electromagnetism and Materials covers the entire electromagnetic domain and the physical response of materials to these waves. Professor André Moliton is Director of the Unité de Microélectronique, Optoélectronique et Polymères (Université de Limoges, France), which brings together three groups studying the optoelectronics of molecular and polymer layers, micro-optoelectronic systems for teleco...