WorldWideScience

Sample records for air oxidation technology

  1. Progress of catalytic wet air oxidation technology

    Directory of Open Access Journals (Sweden)

    Guolin Jing

    2016-11-01

    Full Text Available Catalytic wet air oxidation (CWAO is one of the most economical and environmental-friendly advanced oxidation process for high strength, toxic, hazardous and non-biodegradable contaminants under milder conditions, which is developed on the basic of wet air oxidation. Various heterogeneous catalysts including noble metals and metal oxides have been extensively studied to enhance the efficiency of CWAO. The advances in the research on wastewater treatment by CWAO process are summarized in aspects of reaction mechanism investigation, reaction kinetics study and catalyst development. It is pointed out that the preparation of active and stable catalysts, the investigation on reaction mechanisms and the study on reaction kinetics models are very important for the promotion of CWAO application.

  2. Experimental research on photocatalytic oxidation air purification technology applied to aircraft cabins

    DEFF Research Database (Denmark)

    Sun, Yuexia; Fang, Lei; Wyon, David Peter

    2008-01-01

    The experiment presented in this report was performed in a simulated aircraft cabin to evaluate the air cleaning effects of two air purification devices that used photocatalytic oxidation (PCO) technology. Objective physical, chemical and physiological measurements and subjective human assessments...

  3. USING WET AIR OXIDATION TECHNOLOGY TO DESTROY TETRAPHENYLBORATE

    Energy Technology Data Exchange (ETDEWEB)

    Adu-Wusu, K; Daniel McCabe, D; Bill Wilmarth, B

    2007-04-04

    A bench-scale feasibility study on the use of a Wet Air Oxidation (WAO) process to destroy a slurry laden with tetraphenylborate (TPB) compounds has been undertaken. WAO is an aqueous phase process in which soluble and/or insoluble waste constituents are oxidized using oxygen or oxygen in air at elevated temperatures and pressures ranging from 150 C and 1 MPa to 320 C and 22 MPa. The products of the reaction are CO{sub 2}, H{sub 2}O, and low molecular weight oxygenated organics (e.g. acetate, oxalate). Test results indicate WAO is a feasible process for destroying TPB, its primary daughter products [triphenylborane (3PB), diphenylborinic acid (2PB), and phenylboronic acid (1PB)], phenol, and most of the biphenyl byproduct. The required conditions are a temperature of 300 C, a reaction time of 3 hours, 1:1 feed slurry dilution with 2M NaOH solution, the addition of CuSO{sub 4}.5H{sub 2}O solution (500 mg/L Cu) as catalyst, and the addition of 2000 mL/L of antifoam. However, for the destruction of TPB, its daughter compounds (3PB, 2PB, and 1PB), and phenol without consideration for biphenyl destruction, less severe conditions (280 C and 1-hour reaction time with similar remaining above conditions) are adequate.

  4. Experimental research on photocatalytic oxidation air purification technology applied to aircraft cabins

    DEFF Research Database (Denmark)

    Sun, Yuexia; Fang, Lei; Wyon, David P.

    2005-01-01

    The experiment presented in this report was performed in a simulated aircraft cabin to evalu-ate the air cleaning effects of two air purification devices using Photocatalytic Oxidation (PCO) technology. Objective physical, chemical and physiological measurements and subjec-tive human assessments...

  5. A review of wet air oxidation and Thermal Hydrolysis technologies in sludge treatment.

    Science.gov (United States)

    Hii, Kevin; Baroutian, Saeid; Parthasarathy, Raj; Gapes, Daniel J; Eshtiaghi, Nicky

    2014-03-01

    With rapid world population growth and strict environmental regulations, increasingly large volumes of sludge are being produced in today's wastewater treatment plants (WWTP) with limited disposal routes. Sludge treatment has become an essential process in WWTP, representing 50% of operational costs. Sludge destruction and resource recovery technologies are therefore of great ongoing interest. Hydrothermal processing uses unique characteristics of water at elevated temperatures and pressures to deconstruct organic and inorganic components of sludge. It can be broadly categorized into wet oxidation (oxidative) and thermal hydrolysis (non-oxidative). While wet air oxidation (WAO) can be used for the final sludge destruction and also potentially producing industrially useful by-products such as acetic acid, thermal hydrolysis (TH) is mainly used as a pre-treatment method to improve the efficiency of anaerobic digestion. This paper reviews current hydrothermal technologies, roles of wet air oxidation and thermal hydrolysis in sludge treatment, and challenges faced by these technologies.

  6. Experimental research on photocatalytic oxidation air purification technology applied to aircraft cabins

    DEFF Research Database (Denmark)

    Sun, Yuexia; Fang, Lei; Wyon, David P.

    2005-01-01

    The experiment presented in this report was performed in a simulated aircraft cabin to evalu-ate the air cleaning effects of two air purification devices using Photocatalytic Oxidation (PCO) technology. Objective physical, chemical and physiological measurements and subjec-tive human assessments ...... observed after the first 3¼ hours of exposure. After 6 hours of expo-sure, a positive effect of using either PCO units on symptoms of dizziness and claustrophobia were observed....

  7. Parametric Evaluation of an Innovative Ultra-Violet PhotocatalyticOxidation (UVPCO) Air Cleaning Technology for Indoor Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, Alfred T.; Sullivan, Douglas P.; Fisk, William J.

    2005-10-31

    An innovative Ultra-Violet Photocatalytic Oxidation (UVPCO) air cleaning technology employing a semitransparent catalyst coated on a semitransparent polymer substrate was evaluated to determine its effectiveness for treating mixtures of volatile organic compounds (VOCs) representative of indoor environments at low, indoor-relevant concentration levels. The experimental UVPCO contained four 30 by 30-cm honeycomb monoliths irradiated with nine UVA lamps arranged in three banks. A parametric evaluation of the effects of monolith thickness, air flow rate through the device, UV power, and reactant concentrations in inlet air was conducted for the purpose of suggesting design improvements. The UVPCO was challenged with three mixtures of VOCs. A synthetic office mixture contained 27 VOCs commonly measured in office buildings. A building product mixture was created by combining sources including painted wallboard, composite wood products, carpet systems, and vinyl flooring. The third mixture contained formaldehyde and acetaldehyde. Steady state concentrations were produced in a classroom laboratory or a 20-m{sup 3} chamber. Air was drawn through the UVPCO, and single-pass conversion efficiencies were measured from replicate samples collected upstream and downstream of the reactor. Thirteen experiments were conducted in total. In this UVPCO employing a semitransparent monolith design, an increase in monolith thickness is expected to result in general increases in both reaction efficiencies and absolute reaction rates for VOCs oxidized by photocatalysis. The thickness of individual monolith panels was varied between 1.2 and 5 cm (5 to 20 cm total thickness) in experiments with the office mixture. VOC reaction efficiencies and rates increased with monolith thickness. However, the analysis of the relationship was confounded by high reaction efficiencies in all configurations for a number of compounds. These reaction efficiencies approached or exceeded 90% for alcohols, glycol

  8. Air Cleaning Technologies

    Science.gov (United States)

    2005-01-01

    Executive Summary Objective This health technology policy assessment will answer the following questions: When should in-room air cleaners be used? How effective are in-room air cleaners? Are in-room air cleaners that use combined HEPA and UVGI air cleaning technology more effective than those that use HEPA filtration alone? What is the Plasmacluster ion air purifier in the pandemic influenza preparation plan? The experience of severe acute respiratory syndrome (SARS) locally, nationally, and internationally underscored the importance of administrative, environmental, and personal protective infection control measures in health care facilities. In the aftermath of the SARS crisis, there was a need for a clearer understanding of Ontario’s capacity to manage suspected or confirmed cases of airborne infectious diseases. In so doing, the Walker Commission thought that more attention should be paid to the potential use of new technologies such as in-room air cleaning units. It recommended that the Medical Advisory Secretariat of the Ontario Ministry of Health and Long-Term Care evaluate the appropriate use and effectiveness of such new technologies. Accordingly, the Ontario Health Technology Advisory Committee asked the Medical Advisory Secretariat to review the literature on the effectiveness and utility of in-room air cleaners that use high-efficiency particle air (HEPA) filters and ultraviolet germicidal irradiation (UVGI) air cleaning technology. Additionally, the Ontario Health Technology Advisory Committee prioritized a request from the ministry’s Emergency Management Unit to investigate the possible role of the Plasmacluster ion air purifier manufactured by Sharp Electronics Corporation, in the pandemic influenza preparation plan. Clinical Need Airborne transmission of infectious diseases depends in part on the concentration of breathable infectious pathogens (germs) in room air. Infection control is achieved by a combination of administrative, engineering

  9. Experimental coupling and modelling of wet air oxidation and packed-bed biofilm reactor as an enhanced phenol removal technology.

    Science.gov (United States)

    Minière, Marine; Boutin, Olivier; Soric, Audrey

    2017-01-25

    Experimental coupling of wet air oxidation process and aerobic packed-bed biofilm reactor is presented. It has been tested on phenol as a model refractory compound. At 30 MPa and 250 °C, wet air oxidation batch experiments led to a phenol degradation of 97% and a total organic carbon removal of 84%. This total organic carbon was mainly due to acetic acid. To study the interest of coupling processes, wet air oxidation effluent was treated in a biological treatment process. This step was made up of two packed-bed biofilm reactors in series: the first one acclimated to phenol and the second one to acetic acid. After biological treatment, phenol and total organic carbon removal was 99 and 97% respectively. Thanks to parameters from literature, previous studies (kinetic and thermodynamic) and experimental data from this work (hydrodynamic parameters and biomass characteristics), both treatment steps were modelled. This modelling allows the simulation of the coupling process. Experimental results were finally well reproduced by the continuous coupled process model: relative error on phenol removal efficiency was 1 and 5.5% for wet air oxidation process and packed-bed biofilm reactor respectively.

  10. TASK TECHNICAL AND QUALITY ASSURANCE PLAN FOR OUT-OF-TANK DESTRUCTION OF TETRAPHENYLBORATE VIA WET AIR OXIDATION TECHNOLOGY: PHASE I - BENCH SCALE TESTS

    Energy Technology Data Exchange (ETDEWEB)

    Adu-Wusu, K

    2006-03-31

    Tank 48H return to service is critical to the processing of high level waste (HLW) at Savannah River Site (SRS). Liquid Waste Disposition (LWD) management has the goal of returning Tank 48H to routine service by January 2010 or as soon as practical. Tank 48H currently holds legacy material containing organic tetraphenylborate (TPB) compounds from the operation of the In-Tank Precipitation process. This material is not compatible with the waste treatment facilities at SRS and must be removed or undergo treatment to destroy the organic compounds before the tank can be returned to Tank Farm service. Tank 48H currently contains {approx}240,000 gallons of alkaline slurry with about 2 wt % potassium and cesium tetraphenylborate (KTPB and CsTPB). The main radioactive component in Tank 48H is {sup 137}Cs. The waste also contains {approx}0.15 wt % Monosodium Titanate (MST) which has adsorbed {sup 90}Sr, U, and Pu isotopes. A System Engineering Evaluation of technologies/ideas for the treatment of TPB identified Wet Air Oxidation (WAO) as a leading alternative technology to the baseline aggregation approach. Over 75 technologies/ideas were evaluated overall. Forty-one technologies/ideas passed the initial screening evaluation. The 41 technologies/ideas were then combined to 16 complete solutions for the disposition of TPB and evaluated in detail. Wet Air Oxidation (WAO) is an aqueous phase process in which soluble or suspended waste components are oxidized using molecular oxygen contained in air. The process operates at elevated temperatures and pressures ranging from 150 to 320 C and 7 to 210 atmospheres, respectively. The products of the reaction are CO{sub 2}, H{sub 2}O, and low molecular weight oxygenated organics (e.g. acetate, oxalate). The basic flow scheme for a typical WAO system is as follows. The waste solution or slurry is pumped through a high-pressure feed pump. An air stream containing sufficient oxygen to meet the oxygen requirements of the waste stream is

  11. INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

    Science.gov (United States)

    Bench scale laboratory studies and pilot scale studies in a simulated field-test situation were performed to evaluate the integration of gas-solid ultaviolet (UV) photocatalytic oxidation (PCO) downstream if an air stripper unit as a technology for cost-effectively treating water...

  12. An Innovative Reactor Technology to Improve Indoor Air Quality

    Energy Technology Data Exchange (ETDEWEB)

    Rempel, Jane [TIAX LLC., Lexington, MA (United States)

    2013-03-30

    As residential buildings achieve tighter envelopes in order to minimize energy used for space heating and cooling, accumulation of indoor air pollutants such as volatile organic compounds (VOCs), becomes a major concern causing poor air quality and increased health risks. Current VOC removal methods include sorbents, ultraviolet photocatalytic oxidation (UVPCO), and increased ventilation, but these methods do not capture or destroy all VOCs or are prohibitively expensive to implement. TIAX's objective in this program was to develop a new VOC removal technology for residential buildings. This novel air purification technology is based on an innovative reactor and light source design along with UVPCO properties of the chosen catalyst to purify indoor air and enhance indoor air quality (IAQ). During the program we designed, fabricated and tested a prototype air purifier to demonstrate its feasibility and effectiveness. We also measured kinetics of VOC destruction on photocatalysts, providing deep insight into reactor design.

  13. Disruptive Innovation in Air Measurement Technology: Reality ...

    Science.gov (United States)

    This presentation is a big picture overview on the changing state of air measurement technology in the world, with a focus on the introduction of low-cost sensors into the market place. The presentation discusses how these new technologies may be a case study in disruptive innovation for the air pollution measurement field. The intended audience is primarily those with experience in air pollution measurement methods, but much of the talk is accessible to the general public. This is a keynote presentation on emerging air monitoring technology, to be provided at the AWMA measurements conference in March, 2016.

  14. Air Conditioning and Heating Technology--II.

    Science.gov (United States)

    Gattone, Felix

    Twenty-eight chapters and numerous drawings provide information for instructors and students of air conditioning and heating technology. Chapter 1 lists the occupational opportunities in the field. Chapter 2 covers the background or development of the industry of air conditioning and heating technology. Chapter 3 includes some of the principle…

  15. Air Conditioning and Heating Technology--II.

    Science.gov (United States)

    Gattone, Felix

    Twenty-eight chapters and numerous drawings provide information for instructors and students of air conditioning and heating technology. Chapter 1 lists the occupational opportunities in the field. Chapter 2 covers the background or development of the industry of air conditioning and heating technology. Chapter 3 includes some of the principle…

  16. LTE-advanced air interface technology

    CERN Document Server

    Zhang, Xincheng

    2012-01-01

    Opportunities are at hand for professionals eager to learn and apply the latest theories and practices in air interface technologies. Written by experienced researchers and professionals, LTE-Advanced Air Interface Technology thoroughly covers the performance targets and technology components studied by 3GPP for LTE-Advanced. Besides being an explanatory text about LTE-Advanced air interface technology, this book exploits the technical details in the 3GPP specification, and explains the motivation and implication behind the specifications.After a general description of wireless cellular techno

  17. GaSe oxidation in air: from bulk to monolayers

    Science.gov (United States)

    Rahaman, Mahfujur; Rodriguez, Raul D.; Monecke, Manuel; Lopez-Rivera, Santos A.; Zahn, Dietrich R. T.

    2017-10-01

    Two-dimensional (2D) van derWaals semiconductors have been the subject of intense research due to their low dimensionality and tunable optoelectronic properties. However, the stability of these materials in air is one of the important issues that needs to be clarified, especially for technological applications. Here the time evolution of GaSe oxidation from monolayer to bulk is investigated by Raman spectroscopy, photoluminescence emission, and x-ray photoelectron spectroscopy. The Raman spectroscopy study reveals that GaSe monolayers become oxidized almost immediately after exposure to air. However, the oxidation is a self-limiting process taking roughly 5 h to penetrate up to 3 layers of GaSe. After oxidation, GaSe single-layers decompose into amorphous Se which has a strong Raman cross section under red excitation. The present study provides a clear picture of the stability of GaSe in air and will guide future research of GaSe from single- to few-layers for the appropriate development of novel technological applications for this promising 2D material.

  18. A Tire Air Maintenance Technology

    Science.gov (United States)

    Pierce, Alan

    2012-01-01

    Improperly inflated car tires can reduce gas mileage and car performance, speed up tire wear, and even cause a tire to blow out. The AAA auto club recommends that someone check the air pressure of one's car's tires at least once a month. Wouldn't it be nice, though, if someone came up with a tire pressure-monitoring system that automatically kept…

  19. Cryogenic hydrogen-induced air liquefaction technologies

    Science.gov (United States)

    Escher, William J. D.

    1990-01-01

    Extensively utilizing a special advanced airbreathing propulsion archives database, as well as direct contacts with individuals who were active in the field in previous years, a technical assessment of cryogenic hydrogen-induced air liquefaction, as a prospective onboard aerospace vehicle process, was performed and documented. The resulting assessment report is summarized. Technical findings are presented relating the status of air liquefaction technology, both as a singular technical area, and also that of a cluster of collateral technical areas including: compact lightweight cryogenic heat exchangers; heat exchanger atmospheric constituents fouling alleviation; para/ortho hydrogen shift conversion catalysts; hydrogen turbine expanders, cryogenic air compressors and liquid air pumps; hydrogen recycling using slush hydrogen as heat sink; liquid hydrogen/liquid air rocket-type combustion devices; air collection and enrichment systems (ACES); and technically related engine concepts.

  20. Coal char oxidation kinetics in air medium

    Directory of Open Access Journals (Sweden)

    Korotkikh Alexander G.

    2017-01-01

    Full Text Available Study of oxidation kinetics for three types of coal char with different carbon content in air is presented. The coal char powders of anthracite, bituminous T-grade coal and 2B-grade lignite with particle size less than 80 μm were tested. The coal char oxidation was researched by isothermal method via simultaneous TG-DSC analyzer Netzsch STA 449 Jupiter F3 in the temperature range of 1000–1200 °C. Measurements were carried out at ambient pressure. Volumetric flow rate of oxidizing medium into analyser chamber was 250 ml/min. Flow consisted of air and argon with volumetric ratio 24/1. Carbon average rate of oxidation reaction at each temperature were defined based on experimental results. Kinetic constants (the frequency factor and activation energy were defined for Arrhenius equation modified with three submodels: volumetric model, shrinking core model and random pore model. The activation energy values for anthracite are 1,6-1,7 times higher than for chars of bituminous coal and lignite.

  1. Compressed air energy storage technology program

    Science.gov (United States)

    Loscutoff, W. V.

    1980-06-01

    Progress in the development of compressed air energy storage (CAES) technologies for central station electric utility applications is reported. It is reported that the concept improves the effectiveness of a gas turbine using petroleum fuels, could reduce petroleum fuel consumption of electric utility peaking plants, and is technically feasible and economically viable. Specific topics discussed include stability criteria for large underground reservoirs in salt domes, hard rock, and porous rock used for air storage in utility applications and second-generation technologies that have minimal or no dependence on petroleum fuels. The latter includes integration of thermal energy storage, fluidized bed combustion, or coal gasification with CAES.

  2. Traffic air pollution and oxidized LDL.

    Directory of Open Access Journals (Sweden)

    Lotte Jacobs

    Full Text Available BACKGROUND: Epidemiologic studies indirectly suggest that air pollution accelerates atherosclerosis. We hypothesized that individual exposure to particulate matter (PM derived from fossil fuel would correlate with plasma concentrations of oxidized low-density lipoprotein (LDL, taken as a marker of atherosclerosis. We tested this hypothesis in patients with diabetes, who are at high risk for atherosclerosis. METHODOLOGY/PRINCIPAL FINDINGS: In a cross-sectional study of non-smoking adult outpatients with diabetes we assessed individual chronic exposure to PM by measuring the area occupied by carbon in airway macrophages, collected by sputum induction and by determining the distance from the patient's residence to a major road, through geocoding. These exposure indices were regressed against plasma concentrations of oxidized LDL, von Willebrand factor and plasminogen activator inhibitor 1 (PAI-1. We could assess the carbon load of airway macrophages in 79 subjects (58 percent. Each doubling in the distance of residence from major roads was associated with a 0.027 µm(2 decrease (95% confidence interval (CI: -0.048 to -0.0051 in the carbon load of airway macrophages. Independently from other covariates, we found that each increase of 0.25 µm(2 [interquartile range (IQR] in carbon load was associated with an increase of 7.3 U/L (95% CI: 1.3 to 13.3 in plasma oxidized LDL. Each doubling in distance of residence from major roads was associated with a decrease of -2.9 U/L (95% CI: -5.2 to -0.72 in oxidized LDL. Neither the carbon load of macrophages nor the distance from residence to major roads, were associated with plasma von Willebrand factor or PAI-1. CONCLUSIONS: The observed positive association, in a susceptible group of the general population, between plasma oxidized LDL levels and either the carbon load of airway macrophages or the proximity of the subject's residence to busy roads suggests a proatherogenic effect of traffic air pollution.

  3. A comparison of innovative air pollution control technology demonstrations at McClellan Air Force Base

    Energy Technology Data Exchange (ETDEWEB)

    Chapman, T.E. [BDM Federal, McClellan AFB, CA (United States); Mook, P.H. Jr.; Wong, K.B. [SM-ALC/EMR, McClellan AFB, CA (United States)

    1997-12-31

    McClellan Air Force Base (AFB), located near Sacramento, California, is one of the Strategic Environmental Research and Development Program`s National Environmental Technology Test Sites. As part of the on-going environmental clean-up of McClellan AFB, the US Air Force has evaluated several innovative and conventional technologies for the treatment of vapor phase volatile organic compounds (VOCs). This paper presents an overview and comparison of the cost and performance of seven innovative technologies tested at McClellan AFB. McClellan AFB has found conventional off-gas treatment technologies to be effective but costly. Operation and maintenance (O and M) costs for treatment systems are increasingly becoming a major component of the environmental clean-up budget. The cost and performance of photolytic destruction, titanium dioxide photocatalytic oxidation, advanced polymer absorption media, flameless thermal oxidation, non-thermal plasma destruction, electron-beam destruction, and an advanced regenerative adsorption system are presented. Destruction removal efficiencies for VOCs have ranged from greater than 99.9 percent for flameless thermal oxidation to zero for the advanced polymer absorption media. Like the conventional technologies in use, all of the innovative technologies tested have been shown to be effective for treating a wide range of vapor phase contaminants, but each is only cost effective over limited range of off-gas concentrations. Some of the innovative technologies evaluated were found not to be useful over a wide range of contaminants or too costly to operate at their current stage of development. For example, titanium dioxide photocatalytic oxidation cannot effectively treat chlorinated VOCs in off-gas streams that contain moderate amounts of long-chain hydrocarbons.

  4. Photocatalytic materials and technologies for air purification.

    Science.gov (United States)

    Ren, Hangjuan; Koshy, Pramod; Chen, Wen-Fan; Qi, Shaohua; Sorrell, Charles Christopher

    2017-03-05

    Since there is increasing concern for the impact of air quality on human health, the present work surveys the materials and technologies for air purification using photocatalytic materials. The coverage includes (1) current photocatalytic materials for the decomposition of chemical contaminants and disinfection of pathogens present in air and (2) photocatalytic air purification systems that are used currently and under development. The present work focuses on five main themes. First, the mechanisms of photodegradation and photodisinfection are explained. Second, system designs for photocatalytic air purification are surveyed. Third, the photocatalytic materials used for air purification and their characteristics are considered, including both conventional and more recently developed photocatalysts. Fourth, the methods used to fabricate these materials are discussed. Fifth, the most significant coverage is devoted to materials design strategies aimed at improving the performance of photocatalysts for air purification. The review concludes with a brief consideration of promising future directions for materials research in photocatalysis. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. QuestAir hydrogen separation technology

    Energy Technology Data Exchange (ETDEWEB)

    Henkel, B. [QuestAir Technologies Inc., Burnaby, British Columbia (Canada)

    2006-07-01

    QuestAir's gas purification products employ a process known as pressure swing adsorption (PSA). PSA is based on the adsorption of gases onto special materials known as adsorbents. These adsorbents remove all contaminants from an impure feed stream to produce a purified product gas. Once the adsorbents are near saturation, the impurities are purged, regenerating the adsorbents for the next PSA cycle. QuestAir's patented technology has reduced the duration of the PSA cycle by up to 10 times, allowing for a similar reduction in the size of system components such as pressure vessels, piping and structural supports. Our simple, compact and reliable technology is a significant improvement over conventional PSA hydrogen purification systems, and it also has significant advantages over other gas purification technologies such as membranes and cryogenic plants.

  6. Green Propulsion Technologies for Advanced Air Transports

    Science.gov (United States)

    Del Rosario, Ruben

    2015-01-01

    Air transportation is critical to U.S. and Global economic vitality. However, energy and climate issues challenge aviations ability to be sustainable in the long term. Aviation must dramatically reduce fuel use and related emissions. Energy costs to U.S. airlines nearly tripled between 1995 and 2011, and continue to be the highest percentage of operating costs. The NASA Advanced Air Transports Technology Project addresses the comprehensive challenge of enabling revolutionary energy efficiency improvements in subsonic transport aircraft combined with dramatic reductions in harmful emissions and perceived noise to facilitate sustained growth of the air transportation system. Advanced technologies and the development of unconventional aircraft systems offer the potential to achieve these improvements. The presentation will highlight the NASA vision of revolutionary systems and propulsion technologies needed to achieve these challenging goals. Specifically, the primary focus is on the N+3 generation; that is, vehicles that are three generations beyond the current state of the art, requiring mature technology solutions in the 2025-30 timeframe, which are envisioned as being powered by Hybrid Electric Propulsion Systems.

  7. Enhanced reversibility and durability of a solid oxide Fe-air redox battery by carbothermic reaction derived energy storage materials.

    Science.gov (United States)

    Zhao, Xuan; Li, Xue; Gong, Yunhui; Huang, Kevin

    2014-01-18

    The recently developed solid oxide metal-air redox battery is a new technology capable of high-rate chemistry. Here we report that the performance, reversibility and stability of a solid oxide iron-air redox battery can be significantly improved by nanostructuring energy storage materials from a carbothermic reaction.

  8. ASSESSMENT OF GALLIUM OXIDE TECHNOLOGY

    Science.gov (United States)

    2017-08-01

    Universe" ...................................... 5 Figure 4: MEA Architecture [60...weight. Figure 4: MEA Architecture [60] 2.2 How Does Ga2O3 Compare to Other Semiconductors? We are paying attention to β-Ga2O3 because of its...growth is possible. • Limited crystal orientation have been demonstrated. • Technology base is narrowly located in Japan . Mainstream technology

  9. HUMID AIR TURBINE CYCLE TECHNOLOGY DEVELOPMENT PROGRAM

    Energy Technology Data Exchange (ETDEWEB)

    Richard Tuthill

    2002-07-18

    The Humid Air Turbine (HAT) Cycle Technology Development Program focused on obtaining HAT cycle combustor technology that will be the foundation of future products. The work carried out under the auspices of the HAT Program built on the extensive low emissions stationary gas turbine work performed in the past by Pratt & Whitney (P&W). This Program is an integral part of technology base development within the Advanced Turbine Systems Program at the Department of Energy (DOE) and its experiments stretched over 5 years. The goal of the project was to fill in technological data gaps in the development of the HAT cycle and identify a combustor configuration that would efficiently burn high moisture, high-pressure gaseous fuels with low emissions. The major emphasis will be on the development of kinetic data, computer modeling, and evaluations of combustor configurations. The Program commenced during the 4th Quarter of 1996 and closed in the 4th Quarter of 2001. It teamed the National Energy Technology Laboratory (NETL) with P&W, the United Technologies Research Center (UTRC), and a subcontractor on-site at UTRC, kraftWork Systems Inc. The execution of the program started with bench-top experiments that were conducted at UTRC for extending kinetic mechanisms to HAT cycle temperature, pressure, and moisture conditions. The fundamental data generated in the bench-top experiments was incorporated into the analytical tools available at P&W to design the fuel injectors and combustors. The NETL then used the hardware to conduct combustion rig experiments to evaluate the performance of the combustion systems at elevated pressure and temperature conditions representative of the HAT cycle. The results were integrated into systems analysis done by kraftWork to verify that sufficient understanding of the technology had been achieved and that large-scale technological application and demonstration could be undertaken as follow-on activity. An optional program extended the

  10. Modern air protection technologies at thermal power plants (review)

    Science.gov (United States)

    Roslyakov, P. V.

    2016-07-01

    Realization of the ecologically safe technologies for fuel combustion in the steam boiler furnaces and the effective ways for treatment of flue gases at modern thermal power plants have been analyzed. The administrative and legal measures to stimulate introduction of the technologies for air protection at TPPs have been considered. It has been shown that both the primary intrafurnace measures for nitrogen oxide suppression and the secondary flue gas treatment methods are needed to meet the modern ecological standards. Examples of the environmentally safe methods for flame combustion of gas-oil and solid fuels in the boiler furnaces have been provided. The effective methods and units to treat flue gases from nitrogen and sulfur oxides and flue ash have been considered. It has been demonstrated that realization of the measures for air protection should be accompanied by introduction of the systems for continuous instrumentation control of the composition of combustion products in the gas path of boiler units and for monitoring of atmospheric emissions.

  11. Assessment of Current and Future Air Pollutant Emission Reduction Technologies for Marine Diesel Engines

    Science.gov (United States)

    2014-02-01

    sulphur present in fuel: the less sulphur content in the fuel, the less SOx in the exhaust. SOx cause acid rain and SOx oxidation in the atmosphere...gases contain gaseous sulphur species that form sulphuric acid , causing corrosion problems [9]. Presentations to the cruise industry in 2009 by MAN...emerging. Most of the air pollutant emission control technologies focus on reducing concentration of nitrogen oxides (NOx), sulphur oxides (SOx), or

  12. Pretreatment of apramycin wastewater by catalytic wet air oxidation

    Institute of Scientific and Technical Information of China (English)

    YANG Shao-xia; FENG Yu-jie; WAN Jia-feng; LIN Qing-ying; ZHU Wan-peng; JIANG Zhan-peng

    2005-01-01

    The pretreatment technology of wet air oxidation(WAO) and coagulation and acidic hydrolysis for apramycin wastewater was investigated in this paper. The COD, apramycin, NH4+ concentration, and the ratio of BOD5/COD were analyzed, and the color and odor of the effluent were observed. WAO of apramycin wastewater, without catalyst and with RuO2/Al2 O3 and RuO2-CeO2/Al2 O3 catalysts, was carried out at degradation temperature of 200℃ and the total pressure of 4 MPa in a 1 L batch reactor. The result showed that the apramycin removals were respectively 50.2% and 55.0%, COD removals were 40.0% and 46.0%, and the ratio of BOD5/COD was increased to 0.49 and 0.54 with RuO2/Al2 O3 and RuO2-CeO2/Al2 O3 catalysts in catylytic wet air oxidation(CWAO) after the reaction of 150 min. With the pretreatment of coagulation and acidic hydrolysis, COD and apramycin removals were slight decreased, and the ratio of BOD5/COD was increased to 0.45, and the effluents was not suitable to biological treatment. The color and odor of the wastewater were the apramycin wastewater. The addition of CeO2 could promote the activity and stability of RuO2/Al2 O3 in WAO of apramycin wastewater.

  13. Sulfur-oxidizing bacteria in environmental technology.

    Science.gov (United States)

    Pokorna, Dana; Zabranska, Jana

    2015-11-01

    Hydrogen sulfide is widely known as the most undesirable component of biogas that caused not only serious sensoric and toxic problems, but also corrosion of concrete and steel structures. Many agricultural and industrial waste used in biogas production, may contain a large amount of substances that serve as direct precursors to the formation of sulfide sulfur-sources of hydrogen sulfide in the biogas. Biological desulfurization methods are currently promoted to abiotic methods because they are less expensive and do not produce undesirable materials which must be disposed of. The final products of oxidation of sulfides are no longer hazardous. Biological removal of sulfide from a liquid or gaseous phase is based on the activity of sulfur-oxidizing bacteria. They need an oxidizing agent such as an acceptor of electrons released during the oxidation of sulfides-atmospheric oxygen or oxidized forms of nitrogen. Different genera of sulfur-oxidizing bacteria and their technological application are discussed.

  14. Wet-air oxidation cleans up black wastewater

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    Sterling Organics produces the analgesic paracetamol (acetaminophen) at its Dudley, England, plant. The wastewater from the batch process contains intermediates such as para-aminophenol (PAP) and byproducts such as thiosulfates, sulfites and sulfides. To stay ahead of increasingly strict environmental legislation, Sterling Organics installed a wet-air oxidation system at the Dudley facility in August 1992. The system is made by Zimpro Environmental Inc. (Rothschild, Wis.). Zimpro's wet-air oxidation system finds a way around the limitations of purely chemical or physical processes. In the process, compressed air at elevated temperature and pressure oxidizes the process intermediates and byproducts and removes the color from the wastewater.

  15. Advanced methods for the treatment of organic aqueous wastes: wet air oxidation and wet peroxide oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Debellefontaine, Hubert; Chakchouk, Mehrez; Foussard, Jean Noel [Institut National des Sciences Appliquees (INSA), 31 - Toulouse (France). Dept. de Genie des Procedes Industriels; Tissot, Daniel; Striolo, Phillipe [IDE Environnement S.A., Toulouse (France)

    1993-12-31

    There is a growing concern about the problems of wastes elimination. Various oxidation techniques are suited for elimination of organic aqueous wastes, however, because of the environmental drawbacks of incineration, liquid phase oxidation should be preferred. `Wet Air Oxidation` and `Wet Peroxide Oxidation`are alternative processes which are discussed in this paper. 17 refs., 13 figs., 4 tabs.

  16. Reduced graphene oxide for Li–air batteries

    DEFF Research Database (Denmark)

    Storm, Mie Møller; Overgaard, Marc; Younesi, Reza

    2015-01-01

    Reduced graphene oxide (rGO) has shown great promise as an air-cathode for Li-air batteries with high capacity. In this article we demonstrate how the oxidation time of graphene oxide (GO) affects the ratio of different functional groups and how trends of these in GO are extended to chemically...... and thermally reduced GO. We investigate how differences in functional groups and synthesis may affect the performance of Li-O-2 batteries. The oxidation timescale of the GO was varied between 30 min and 3 days before reduction. Powder Xray diffraction, micro-Raman, FE-SEM, BET analysis, and XPS were used...

  17. MATRIX PHOTOCATALYTIC, INC. PHOTOCATALYTIC OXIDATION TECHNOLOGY - INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    The Matrix Technology involves the exposure of titanium dioxide (Ti02) particles to ultraviolet light (UV). The Ti02 is activated by UV light to produce high oxidizing hydroxyl radicals. Maxtrix also uses hydrogen peroxide (H202) and ozone (03) to enhance the treatment systems p...

  18. Simulation technology for refrigeration and air conditioning appliances

    Institute of Scientific and Technical Information of China (English)

    DING Guoliang

    2006-01-01

    Simulation technology has been widely used for performance prediction and optimal design of refrigeration and air conditioning appliances. A brief history of simulation technology for refrigeration and air conditioning appliances is reviewed. The models for evaporator, condenser, compressor, capillary tube and thermal insulation layer are summarized, and a fast calculation method for thermodynamic properties of refrigerant is introduced in this paper. The model-based intelligent simulation technology and the simulation technology based on graph theory are also illustrated. Finally, an updated trend of simulation technology development for refrigeration and air conditioning appliances is discussed.

  19. Technology Candidates for Air-to-Air and Air-to-Ground Data Exchange

    Science.gov (United States)

    Haynes, Brian D.

    2015-01-01

    Technology Candidates for Air-to-Air and Air-to-Ground Data Exchange is a two-year research effort to visualize the U. S. aviation industry at a point 50 years in the future, and to define potential communication solutions to meet those future data exchange needs. The research team, led by XCELAR, was tasked with identifying future National Airspace System (NAS) scenarios, determining requirements and functions (including gaps), investigating technical and business issues for air, ground, & air-to-ground interactions, and reporting on the results. The project was conducted under technical direction from NASA and in collaboration with XCELAR's partner, National Institute of Aerospace, and NASA technical representatives. Parallel efforts were initiated to define the information exchange functional needs of the future NAS, and specific communication link technologies to potentially serve those needs. Those efforts converged with the mapping of each identified future NAS function to potential enabling communication solutions; those solutions were then compared with, and ranked relative to, each other on a technical basis in a structured analysis process. The technical solutions emerging from that process were then assessed from a business case perspective to determine their viability from a real-world adoption and deployment standpoint. The results of that analysis produced a proposed set of future solutions and most promising candidate technologies. Gap analyses were conducted at two points in the process, the first examining technical factors, and the second as part of the business case analysis. In each case, no gaps or unmet needs were identified in applying the solutions evaluated to the requirements identified. The future communication solutions identified in the research comprise both specific link technologies and two enabling technologies that apply to most or all specific links. As a result, the research resulted in a new analysis approach, viewing the

  20. Treatment of hydraulic fracturing wastewater by wet air oxidation.

    Science.gov (United States)

    Wang, Wei; Yan, Xiuyi; Zhou, Jinghui; Ma, Jiuli

    2016-01-01

    Wastewater produced by hydraulic fracturing for oil and gas production is characterized by high salinity and high chemical oxygen demand (COD). We applied a combination of flocculation and wet air oxidation technology to optimize the reduction of COD in the treatment of hydraulic fracturing wastewater. The experiments used different values of flocculant, coagulant, and oxidizing agent added to the wastewater, as well as different reaction times and treatment temperatures. The use of flocculants for the pretreatment of fracturing wastewater was shown to improve treatment efficiency. The addition of 500 mg/L of polyaluminum chloride (PAC) and 20 mg/L of anionic polyacrylamide (APAM) during pretreatment resulted in a COD removal ratio of 8.2% and reduced the suspended solid concentration of fracturing wastewater to 150 mg/L. For a solution of pretreated fracturing wastewater with 12 mL of added H2O2, the COD was reduced to 104 mg/L when reacted at 300 °C for 75 min, and reduced to 127 mg/L when reacted at the same temperature for 45 min while using a 1 L autoclave. An optimal combination of these parameters produced treated wastewater that met the GB 8978-1996 'Integrated Wastewater Discharge Standard' level I emission standard.

  1. 75 FR 80833 - Shipboard Air Emission Reduction Technology Report

    Science.gov (United States)

    2010-12-23

    ... existing technology for reducing air emissions from cargo and passenger vessels regulated under the Clean... SECURITY Coast Guard Shipboard Air Emission Reduction Technology Report AGENCY: Coast Guard, DHS. ACTION... cargo and passenger vessels that operate in United States waters and ports. For this study, the Coast...

  2. Lower cost air measurement technology – what is on the ...

    Science.gov (United States)

    This presentation is to the MARAMA 2014 annual monitoring meeting and is an invited talk to provide an overview on lower cost air measurement technology. This presentation is to the MARAMA 2014 annual monitoring meeting and is an invited talk to provide an overview on lower cost air measurement technology.

  3. A new technology for air-entrainment of concrete

    DEFF Research Database (Denmark)

    Laustsen, Sara; Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    2008-01-01

    reservoirs are distributed throughout the concrete. During the hydration process the cement paste imbibes water from the water-filled SAP voids. Thereby the water-filled SAP voids turn into partly air-filled voids. The advantages of the SAP-based technology compared to traditional chemical air......This paper describes a new technology for air-entrainment of concrete. The technology is based on the addition of dry superabsorbent polymers (SAP) to the concrete. A large amount of small internal water reservoirs are formed during mixing when SAP absorbs water and swells. The internal water......-entrainment include stability of the air void system and improved control of both the amount of added air and the air void size. The new technology based on SAP has been tested in freeze-thaw experiments, where the amount of surface scaling was measured. The results clearly show that SAP is beneficial for frost...

  4. A study of mercuric oxide and zinc-air battery life in hearing aids.

    Science.gov (United States)

    Sparkes, C; Lacey, N K

    1997-09-01

    The requirement to phase out mercuric oxide (mercury) batteries on environmental grounds has led to the widespread introduction of zinc-air technology. The possibility arises that high drain hearing aids may not be adequately catered for by zinc-air cells, leading to poor performance. This study investigated the hearing aid user's ability to perceive differences between zinc-air and mercury cells in normal everyday usage. The data was collected for 100 experienced hearing aid users in field trials. Users report 50 per cent greater life for zinc-air cells in high power aids and 28 per cent in low power aids. The average life of the zinc-air cells range from 15 days in high power to 34 days in low power aids. Users are able to perceive a difference in sound quality in favour of zinc-air cells for low and medium power aids. The hearing aid population is not disadvantaged by phasing out mercury cells.

  5. The Oxides of Nitrogen in Air Pollution.

    Science.gov (United States)

    California State Air Resources Board, Sacramento.

    Research on the health effects of oxides of nitrogen and on the role of oxides of nitrogen in producing photochemical smog effects is presented in this report. Prepared by the California State Department of Public Health at the request of the State Legislature, it gives a comprehensive review of available information, as well as the need for air…

  6. Kinetics of Fe3O4 formation by air oxidation

    Institute of Scientific and Technical Information of China (English)

    杨喜云; 龚竹青; 刘丰良

    2004-01-01

    The kinetics of Fe3O4 formation by air oxidation of slightly acidic suspension of Fe(OH)2 was studied. The effects of initial concentration of Fe(Ⅱ), temperature, partial pressure of oxygen, air flow rate and stirring rate on the oxidation rate were investigated. The results show that Fe3O4 formation is composed of two-step reaction, the first step is the formation of Fe(OH)+2 by oxidation of Fe(OH)+ complex ions, the second step is the formation of magnetite by dehydration and deprotonation of Fe(OH)+ and Fe(OH)+2. The oxidation reaction is zero-order with respect to the concentration of Fe(Ⅱ) and around 0.5-order with respect to partial pressure of oxygen, and oxygen transfer process is rate-limiting step of oxidation reaction with apparent activation energy of 2.74 kJ·mol-1.

  7. Air Quality Monitoring and Sensor Technologies

    Science.gov (United States)

    EPA scientist Ron Williams presented on the features, examination, application, examples, and data quality of continuous monitoring study designs at EPA's Community Air Monitoring Training in July 2015.

  8. Technology and complete set of the equipment of air-plasma method for synthesis of nanoaerosols

    Science.gov (United States)

    Kopytin, Yurii D.; Novikov, O. G.

    2004-02-01

    The paper is aimed at studying synthesis and construction, as well as physical-chemical characteristics of nanoaerosols. The technology and product line of the Air-plasma method for synthesis of metal oxide nanopowders to obtain high-performance ceramics (PSNP) is hot and set at manufacturing different-types zirconium ceramics stabilized by yttrium and magnesium oxides, as well as other dopes. For the available equipment, the technologies of producing nanopowders of other metal oxides alongside with circonium oxide and composite oxides (Al203, Ti02, CuO, SiO2, Fe2O2, ZnO, CoO, Cr2O3, PbO, MnO, MgO, CaO, CeO, etc.) are developed and adapted.

  9. Catalytic wet Air Oxidation of o-Chlorophenol in Wastewater

    Institute of Scientific and Technical Information of China (English)

    徐新华; 汪大翬

    2003-01-01

    Catalytic wet air oxidation (CWAO) was investigated in laboratory-scale experiments for the treatment of o-chlorophenol in wastewater. Experimental results showed that wet air oxidation (WAO) process in the absence of catalyst was also effective for o-chlorophenol in wastewater treatment. Up to 80% of the initial CODCr was removed by wet air oxidation at 270℃ with twice amount of the required stoichiometric oxygen supply. At temperature of 150℃, the removal rate of CODCr was only 30%. Fe2(SO4)3, CuSO4, Cu(NO3)2 and MnSO4 exhibited high catalytic activity. Higher removal rate of CODCr was obtained by CWAO. More than 96% of the initial CODCr was removed at 270℃ and 84.6%-93.6% of the initial CODCr was removed at 150℃. Mixed catalysts had better catalytic activity for the degradation of o-chlorophenol in wastewater.

  10. Air oxidation of Zircaloy, Part 1 – Review of correlations

    Energy Technology Data Exchange (ETDEWEB)

    Stempniewicz, M.M., E-mail: stempniewicz@nrg.eu

    2016-05-15

    Highlights: • Models for air oxidation of Zircaloy 4 reviewed. • Models for air oxidation of Zircaloy 4 compared with data. • Models for breakaway in air oxidation compared with data. - Abstract: The accident in Fukushima brought up new issues in the area of safety of nuclear reactors. Among others, Spent Fuel Pool accidents gained new focus. The computer codes applicable for safety analyses of Nuclear Power Plants have limited verification and validation in this area and their applicability remains still to be proven. An important phenomenon occurring during loss of water in SFP is air oxidation of Zircaloy cladding material. Mathematical modeling of this phenomenon in computer codes has been under development during the last years. This document presents a review of models for air oxidation of Zircaloy alloys, including up to date models available in open literature, as well as models available in computer codes ASTEC and MELCOR. The models were tested by performing simulations of a number air oxidation experiments from ANL, KIT, and IRSN. It was found out that the ASTEC model gives somewhat better agreement with data than the MELCOR model for the ANL and KIT experiments. The reaction rates from the MELCOR model differ from experiments by factor of 2 and 3 respectively. In case of IRSN tests, the MELCOR model gives better agreement with data. The reaction rates from the ASTEC model differ from experiment by roughly a factor of 3. The difference between the reaction rates predicted by the models and obtained from experiments was found to be up to about factor of three. The ASTEC model gives generally qualitatively better representation of reality. A disadvantage is the use of Boase and Vandergraaf correlation outside its validity range (T > 1000 K) where it is underestimating the reaction rate. In the MELCOR model the following qualitative behavior is incorrect: breakaway occurs in the entire temperature range, while experiments show that it occurs only for

  11. Metal oxide electrocatalysts for alternative energy technologies

    Science.gov (United States)

    Pacquette, Adele Lawren

    This dissertation focuses on the development of metal oxide electrocatalysts with varying applications for alternative energy technologies. Interest in utilizing clean, renewable and sustainable sources of energy for powering the planet in the future has received much attention. This will address the growing concern of the need to reduce our dependence on fossil fuels. The facile synthesis of metal oxides from earth abundant metals was explored in this work. The electrocatalysts can be incorporated into photoelectrochemical devices, fuel cells, and other energy storage devices. The first section addresses the utilization of semiconductors that can harness solar energy for water splitting to generate hydrogen. An oxysulfide was studied in order to combine the advantageous properties of the stability of metal oxides and the visible light absorbance of metal chalcogenides. Bi 2O2S was synthesized under facile hydrothermal conditions. The band gap of Bi2O2S was smaller than that of its oxide counterpart, Bi2O3. Light absorption by Bi 2O2S was extended to the visible region (>600 nm) in comparison to Bi2O3. The formation of a composite with In 2O3 was formed in order to create a UV irradiation protective coating of the Bi2O2S. The Bi2O2S/In 2O3 composite coupled with a dye CrTPP(Cl) and cocatalysts Pt and Co3O4 was utilized for water splitting under light irradiation to generate hydrogen and oxygen. The second section focuses on improving the stability and light absorption of semiconductors by changing the shapes and morphologies. One of the limitations of semiconductor materials is that recombination of electron-hole pairs occur within the bulk of the materials instead of migration to the surface. Three-dimensional shapes, such as nanorods, can prevent this recombination in comparison to spherical particles. Hierarchical structures, such as dendrites, cubes, and multipods, were synthesized under hydrothermal conditions, in order to reduce recombination and improve

  12. Rapid evolution of air sensor technologies

    Science.gov (United States)

    Outdoor air pollution measurement approaches have historically been conducted using stationary shelters that require significant space, power, and expertise to operate. The cost and logistical requirements to conduct monitoring have limited the number of locations with continuou...

  13. Rapid evolution of air sensor technologies

    Science.gov (United States)

    Outdoor air pollution measurement approaches have historically been conducted using stationary shelters that require significant space, power, and expertise to operate. The cost and logistical requirements to conduct monitoring have limited the number of locations with continuou...

  14. Proceedings of the 1994 CACTS conference on air cushion technology

    Energy Technology Data Exchange (ETDEWEB)

    Laframboise, J.E. [ed.

    1995-03-01

    The conference held by the Canadian Air Cushion Technology Society (CACTS) was attended by 56 specialists in the field from around the world. CACTS is devoted to the development and application of air cushion technology, primarily in the transportation domain, but also in industry and other fields where the technology may be of benefit. Some uses for the technology include rescue operations in natural disasters such as flooding and oil spill clean up operations in coastal waters. A total of 20 papers were presented at this meeting. Subjects included air cushion spray booms, amphibious transporters in oil spill events, unconventional propulsion systems for air cushion vehicles, ride control systems, and high-speed hovercraft design. Refs., tabs., figs.

  15. Experimental Investigation of Flow Resistance in a Coal Mine Ventilation Air Methane Preheated Catalytic Oxidation Reactor

    Directory of Open Access Journals (Sweden)

    Bin Zheng

    2015-01-01

    Full Text Available This paper reports the results of experimental investigation of flow resistance in a coal mine ventilation air methane preheated catalytic oxidation reactor. The experimental system was installed at the Energy Research Institute of Shandong University of Technology. The system has been used to investigate the effects of flow rate (200 Nm3/h to 1000 Nm3/h and catalytic oxidation bed average temperature (20°C to 560°C within the preheated catalytic oxidation reactor. The pressure drop and resistance proportion of catalytic oxidation bed, the heat exchanger preheating section, and the heat exchanger flue gas section were measured. In addition, based on a large number of experimental data, the empirical equations of flow resistance are obtained by the least square method. It can also be used in deriving much needed data for preheated catalytic oxidation designs when employed in industry.

  16. Preparation of rare-earth metal complex oxide catalysts for catalytic wet air oxidation

    Institute of Scientific and Technical Information of China (English)

    LI Ning; LI Guangming; YAO Zhenya; ZHAO Jianfu

    2007-01-01

    Catalytic wet air oxidation(CWAO)is one of the most promising technologies for pollution abatement.Developing catalysts with high activity and stability is crucial for the application of the CWAO process.The Mn/Ce complex oxide catalyrsts for CWAO of high concentration phenol containing wastewater were prepared by coprecipitation.The catalyst preparation conditions were optimized by using an orthogonal layout method and single-factor experimental analysis.The Mn/Ce serial catalysts were characterized by Brunauer-Emmett-Teller(BET)analysis and the metal cation leaching was measured by inductively coupled plasma torch-atomic emission spectrometry(ICP-AES).The results show that the catalysts have high catalytic activities even at a low temperature(80℃)and low oxygen partial pressure(0.5 MPa)in a batch reactor.The metallic ion leaching is comparatively low(Mn<6.577 mg/L and Ce<0.6910 mg/L,respectively)in the CWAO process.The phenol,CODCD and TOC removal efficiencies in the solution exceed 98.5% using the optimal catalyst(named CSP).The new catalyst would have a promising application in CWAO treatment of high concentration organic wastewater.

  17. Study on mechanism of wet air oxidation of emulsification wastewater.

    Science.gov (United States)

    Tang, Wen W; Zeng, Xin P; Xiao, Yao M; Gu, Guo W

    2009-04-01

    Wet air oxidation (WAO) can effectively be used to treat high-concentration, non-biodegradable emulsification wastewater that contains nonionic matters. Gas chromatograph analysis of emulsification wastewater after oxidation indicated that a catalyst increased production of fatty acids but could not promote its oxidation between 160 and 180 degrees C. When the temperature was greater than or equal to 220 degrees C, the catalyst not only increased production of fatty acids initially but effectively promoted its oxidation in later stages and significantly reduced the concentration of residual surfactants. Experiments proved that fatty acids (especially acetic acid) were the primary intermediate products and that oxidation of these acids was the rate-limiting step. During the process of catalytic WAO of emulsification wastewater, active oxygen molecules attacked organic matters resulting in production of fatty acids, ketone, alcohol, hydrocarbon, and oligo-polyether through radical chain reactions.

  18. Air Force Research Laboratory Technology Milestones 2008

    Science.gov (United States)

    2008-01-01

    develop a unique measurement platform employing tunable diode laser absorption spectroscopy ( TDLAS ). The TDLAS platform provides a novel approach to...conduct research in the exploration and development of fundamental hypersonic aerospace technologies. TDLAS experiments are scheduled for three of...team expects that the TDLAS measurement platform will achieve Technology Readiness Level 6 status (i.e., system/subsystem model or prototype

  19. Fundamentals of air cleaning technology and its application in cleanrooms

    CERN Document Server

    Xu, Zhonglin

    2014-01-01

    Fundamentals of Air Cleaning Technology and Its Application in Cleanrooms sets up the theoretical framework for cleanrooms. New ideas and methods are presented, which include the characteristic index of cleanrooms, uniform and non-uniform distribution characteristics, the minimum sampling volume, a new concept of outdoor air conditioning and the fundamentals of leakage-preventing layers. Written by an author who can look back on major scientific achievements and 50 years of experience in this field, this book offers a concise and accessible introduction to the fundamentals of air cleaning technology and its application. The work is intended for researchers, college teachers, graduates, designers, technicians and corporate R&D personnel in the field of HVAC and air cleaning technology. Zhonglin Xu is a senior research fellow at China Academy of Building Research.

  20. Development of vehicle magnetic air conditioner (VMAC) technology. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gschneidner, Karl A., Jr.; Pecharsky, V.K.; Jiles, David; Zimm, Carl B.

    2001-08-28

    The objective of Phase I was to explore the feasibility of the development of a new solid state refrigeration technology - magnetic refrigeration - in order to reduce power consumption of a vehicle air conditioner by 30%. The feasibility study was performed at Iowa State University (ISU) together with Astronautics Corporation of America Technology Center (ACATC), Madison, WI, through a subcontract with ISU.

  1. Disruptive Innovation in Air Measurement Technology: Reality or Hype?

    Science.gov (United States)

    This presentation is a big picture overview on the changing state of air measurement technology in the world, with a focus on the introduction of low-cost sensors into the market place. The presentation discusses how these new technologies may be a case study in disruptive innov...

  2. Disruptive Innovation in Air Measurement Technology: Reality or Hype?

    Science.gov (United States)

    This presentation is a big picture overview on the changing state of air measurement technology in the world, with a focus on the introduction of low-cost sensors into the market place. The presentation discusses how these new technologies may be a case study in disruptive innov...

  3. Treatment of refractory organic pollutants in industrial wastewater by wet air oxidation

    Directory of Open Access Journals (Sweden)

    Mingming Luan

    2017-02-01

    Full Text Available Wet air oxidation (WAO is one of the most economical and environmentally-friendly advanced oxidation processes. It makes a promising technology for the treatment of refractory organic pollutants in industrial wastewaters. In wet air oxidation aqueous waste is oxidized in the liquid phase at high temperatures (125–320 °C and pressures (0.5–20 MPa in the presence of an oxygen-containing gas (usually air. The advantages of the process include low operating costs and minimal air pollution discharges. The present review is concerned about the literature published in the treatment of refractory organic pollutants in industrial wastewaters, such as dyes. Phenolics were taken as model pollutants in most cases. Reports on effect of treatment for the WAO of refractory organic pollutants in industrial wastewaters are reviewed, such as emulsified wastewater, TNT red water, etc. Discussions are also made on the mechanism and kinetics of WAO and main technical parameters influencing WAO. Finally, development direction of WAO is summed up.

  4. Cryogenic hydrogen-induced air-liquefaction technologies

    Science.gov (United States)

    Escher, William J. D.

    1990-01-01

    Extensive use of a special advanced airbreathing propulsion archives data base, as well as direct contacts with individuals who were active in the field in previous years, a technical assessment of cryogenic hydrogen induced air liquefaction, as a prospective onboard aerospace vehicle process, was performed and documented in 1986. The resulting assessment report is summarized. Technical findings relating the status of air liquefaction technology are presented both as a singular technical area, and also as that of a cluster of collateral technical areas including: Compact lightweight cryogenic heat exchangers; Heat exchanger atmospheric constituents fouling alleviation; Para/ortho hydrogen shift conversion catalysts; Hydrogen turbine expanders, cryogenic air compressors and liquid air pumps; Hydrogen recycling using slush hydrogen as heat sinks; Liquid hydrogen/liquid air rocket type combustion devices; Air Collection and Enrichment System (ACES); and Technically related engine concepts.

  5. Isothermal Kinetics of Catalyzed Air Oxidation of Diesel Soot

    Directory of Open Access Journals (Sweden)

    R. Prasad

    2011-01-01

    Full Text Available To comply with the stringent emission regulations on soot, diesel vehicles manufacturers more and more commonly use diesel particulate filters (DPF. These systems need to be regenerated periodically by burning soot that has been accumulated during the loading of the DPF. Design of the DPF requires rate of soot oxidation. This paper describes the kinetics of catalytic oxidation of diesel soot with air under isothermal conditions. Kinetics data were collected in a specially designed mini-semi-batch reactor. Under the high air flow rate assuming pseudo first order reaction the activation energy of soot oxidation was found to be, Ea = 160 kJ/ mol. ©2010 BCREC UNDIP. All rights reserved(Received: 14th June 2010, Revised: 18th July 2010, Accepted: 9th August 2010[How to Cite: R. Prasad, V.R. Bella. (2010. Isothermal Kinetics of Catalyzed Air Oxidation of Diesel Soot. Bulletin of Chemical Reaction Engineering and Catalysis, 5(2: 95-101. doi:10.9767/bcrec.5.2.796.95-101][DOI:http://dx.doi.org/10.9767/bcrec.5.2.796.95-101 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/796]Cited by in: ACS 1 |

  6. Control Technologies for Room Air-conditioner and Packaged Air-conditioner

    Science.gov (United States)

    Ito, Nobuhisa

    Trends of control technologies about air-conditioning machineries, especially room or packaged air conditioners, are presented in this paper. Multiple air conditioning systems for office buildings are mainly described as one application of the refrigeration cycle control technologies including sensors for thermal comfort and heating/ cooling loads are also described as one of the system control technologies. Inverter systems and related technologies for driving variable speed compressors are described in both case of including induction motors and brushless DC motors. Technologies for more accurate control to meet various kind of regulations such as ozone layer destruction, energy saving and global warming, and for eliminating harmonic distortion of power source current, as a typical EMC problem, will be urgently desired.

  7. Heterogeneous catalytic wet air oxidation of refractory organic pollutants in industrial wastewaters: a review.

    Science.gov (United States)

    Kim, Kyoung-Hun; Ihm, Son-Ki

    2011-02-15

    Catalytic wet air oxidation (CWAO) is one of the most economical and environmental-friendly advanced oxidation process. It makes a promising technology for the treatment of refractory organic pollutants in industrial wastewaters. Various heterogeneous catalysts including noble metals and metal oxides have been extensively studied to enhance the efficiency of CWAO. The present review is concerned about the literatures published in this regard. Phenolics, carboxylic acids, and nitrogen-containing compounds were taken as model pollutants in most cases, and noble metals such as Ru, Rh, Pd, Ir, and Pt as well as oxides of Cr, Mn, Fe, Co, Ni, Cu, Zn, Mo, and Ce were applied as heterogeneous catalysts. Reports on their characterization and catalytic performances for the CWAO of aqueous pollutants are reviewed. Discussions are also made on the reaction mechanisms and kinetics proposed for heterogeneous CWAO and also on the typical catalyst deactivations in heterogeneous CWAO, i.e. carbonaceous deposits and metal leaching.

  8. Air Force Research Laboratory Technology Milestones 2007

    Science.gov (United States)

    2007-01-01

    Martin Aerodynamics, and ZONA Technology worked with collaborators from the National Aeronautics and Space Administration (NASA) to develop the MEDFFAT...be used on either the wet side (for live fire evaluations) or the dry side (for vehicle and other non-fire-related evaluations). The entire mockup is...devices in common aluminum foil by using inexpensive wet chemical processing. For more information contact publicaffairs@afosr.afmil ° (703)696-7797 U

  9. Technology of Measuring equipment for Air Pollution. Development of Mobile Air Pollution monitoring system (LIDAR)

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Hyung Ki; Song, Ky Seok; Rhee, Young Joo; Kim, Duck Hyun; Yang, Ki Ho; Lee, Jong Min; Cha, Byung Heon; Lee, Kang Soo

    1999-01-01

    Most air pollution monitoring technologies accompany a time-consuming sample treatment process and provides pollution information only for a local area. Thus, they have a critical restriction in monitoring time-dependent pollution variation effectively over the wide range of area both in height and in width. LIDAR (Light detection and ranging) is a new technology to overcome such drawbacks of the existing pollution monitoring technologies and has long been investigated in the advanced countries. The goal of this project is to develop the mobile air pollution monitoring system and to apply the system to the detection of various pollutants, such as ozone, nitrogen dioxide, sulfur dioxide and aerosols.

  10. Integrated Technology Air Cleaners (ITAC): Design and Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Fisk, William J.; Cohn, Sebastian; Destaillats, Hugo; Henzel, Victor; Sidheswaran, Meera; Sullivan, Douglas P.

    2013-09-13

    The primary objective of this project was to design, build, and test an air cleaner for residential use with the potential to substantially improve indoor air quality, or maintain indoor air quality unchanged, when outdoor air ventilation rates are reduced to save energy. Two air cleaners were designed and fabricated. The design targets for airflow rate, fan power, and projected cost were met. In short term laboratory studies, both units performed as expected; however, during field studies in homes, the formaldehyde removal performance of the air cleaners was much lower than expected. In subsequent laboratory studies, incomplete decomposition of some indoor air volatile organic compounds, with formaldehyde as a product of partial decomposition of volatile organic compounds, was confirmed as the explanation for the poor formaldehyde removal performance in the field studies. The amount of formaldehyde produced per unit of decomposition of other volatile organic compounds was substantially diminished by increasing the amount of catalyst on the filter and also by decreasing the air velocity. Together, these two measures reduced formaldehyde production, per unit destruction of other volatile organic compounds, by a factor of four, while increasing the removal efficiency of volatile organic compounds by a factor of 1.4. A company with a southern California office is conducting studies in conjunction with Lawrence Berkeley National Laboratory, with the goal of incorporating the ITAC catalytic air cleaning technology in their future commercial products.

  11. Application of Ventilation Air Methane Oxidization and Waste Heat Utilization Technology in Shanxi Lu’an Gaohe Coal Mine%乏风氧化及余热利用技术在山西潞安高河煤矿的应用

    Institute of Scientific and Technical Information of China (English)

    贾剑

    2014-01-01

    A large amount of coal mine ventilation air methane was directly exhausted into the atmosPhere,which not only intensified the greenhouse effect,but also caused the energy consumPtion,and if an aPProPriate technology was aPPlied to make full use of the mine ventilation air methane,huge benefits in energy saving and environmental Protection would be Produced. This PaPer described the mine ventilation air methane oxidation and the waste heat utilization technology in the home and abroad, emPhatically described the design and aPPlication of the Power generation Project with the mine ventilation methane oxidation in Lu’an Gaohe Mine in Shanxi Province,including the collecting and mixing system of the mine ventilation air methane,the safe delivery system of low-concentration gas,the oxidation system of the mine ventilation air methane,the utilization system of the waste heat and so on,and analyzed the significance of the successful construction of this Project.%大量煤矿乏风瓦斯的直接排空,在加剧温室效应的同时亦造成能源的浪费,而通过采用合适的技术对乏风瓦斯加以利用,将产生巨大的节能环保效益。介绍了国内外煤矿乏风瓦斯氧化及余热利用技术,重点介绍了山西潞安高河煤矿的乏风瓦斯氧化发电项目的设计及应用情况,包括乏风收集及掺混系统、低浓度瓦斯输送安全保障系统、乏风氧化系统、余热利用系统等,并分析了该项目建设成功的意义。

  12. Cyclic Oxidation of High-Temperature Alloy Wires in Air

    Science.gov (United States)

    Reigel, Marissa M.

    2004-01-01

    High-temperature alloy wires are proposed for use in seal applications for future re-useable space vehicles. These alloys offer the potential for improved wear resistance of the seals. The wires must withstand the high temperature environments the seals are subjected to as well as maintain their oxidation resistance during the heating and cooling cycles of vehicle re-entry. To model this, the wires were subjected to cyclic oxidation in stagnant air. of this layer formation is dependent on temperature. Slow growing oxides such as chromia and alumina are desirable. Once the oxide is formed it can prevent the metal from further reacting with its environment. Cyclic oxidation models the changes in temperature these wires will undergo in application. Cycling the temperature introduces thermal stresses which can cause the oxide layer to break off. Re-growth of the oxide layer consumes more metal and therefore reduces the properties and durability of the material. were used for cyclic oxidation testing. The baseline material, Haynes 188, has a Co base and is a chromia former while the other two alloys, Kanthal A1 and PM2000, both have a Fe base and are alumina formers. Haynes 188 and Kanthal A1 wires are 250 pm in diameter and PM2000 wires are 150 pm in diameter. The coiled wire has a total surface area of 3 to 5 sq cm. The wires were oxidized for 11 cycles at 1204 C, each cycle containing a 1 hour heating time and a minimum 20 minute cooling time. Weights were taken between cycles. After 11 cycles, one wire of each composition was removed for analysis. The other wire continued testing for 70 cycles. Post-test analysis includes X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) for phase identification and morphology.

  13. Reduced graphene oxide for Li–air batteries

    DEFF Research Database (Denmark)

    Storm, Mie Møller; Overgaard, Marc; Younesi, Reza;

    2015-01-01

    Reduced graphene oxide (rGO) has shown great promise as an air-cathode for Li-air batteries with high capacity. In this article we demonstrate how the oxidation time of graphene oxide (GO) affects the ratio of different functional groups and how trends of these in GO are extended to chemically...... and thermally reduced GO. We investigate how differences in functional groups and synthesis may affect the performance of Li-O-2 batteries. The oxidation timescale of the GO was varied between 30 min and 3 days before reduction. Powder Xray diffraction, micro-Raman, FE-SEM, BET analysis, and XPS were used...... techniques can enhance the structural understanding of rGO. Different rGO cathodes were tested in Li-O-2 batteries which revealed a difference in overpotentials and discharge capacities for the different rGO's. We report the highest Li-O-2 battery discharge capacity recorded of approximately 60,000 m...

  14. Gas-phase advanced oxidation as an integrated air pollution control technique

    Directory of Open Access Journals (Sweden)

    Getachew A. Adnew

    2016-03-01

    Full Text Available Gas-phase advanced oxidation (GPAO is an emerging air cleaning technology based on the natural self-cleaning processes that occur in the Earth’s atmosphere. The technology uses ozone, UV-C lamps and water vapor to generate gas-phase hydroxyl radicals that initiate oxidation of a wide range of pollutants. In this study four types of GPAO systems are presented: a laboratory scale prototype, a shipping container prototype, a modular prototype, and commercial scale GPAO installations. The GPAO systems treat volatile organic compounds, reduced sulfur compounds, amines, ozone, nitrogen oxides, particles and odor. While the method covers a wide range of pollutants, effective treatment becomes difficult when temperature is outside the range of 0 to 80 °C, for anoxic gas streams and for pollution loads exceeding ca. 1000 ppm. Air residence time in the system and the rate of reaction of a given pollutant with hydroxyl radicals determine the removal efficiency of GPAO. For gas phase compounds and odors including VOCs (e.g. C6H6 and C3H8 and reduced sulfur compounds (e.g. H2S and CH3SH, removal efficiencies exceed 80%. The method is energy efficient relative to many established technologies and is applicable to pollutants emitted from diverse sources including food processing, foundries, water treatment, biofuel generation, and petrochemical industries.

  15. Air oxidation of Zircaloy, Part 2: New model for Zry-4 oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Stempniewicz, M.M., E-mail: stempniewicz@nrg.eu

    2016-05-15

    Highlights: • Recommended set of correlations proposed for air oxidation of Zircaloy-4. • New breakaway correlation for air oxidation of Zircaloy-4. • Improved accuracy of predicting air oxidation of Zircaloy-4. • Models applicable to analyses of accidents in Spent Fuel Pool. - Abstract: The accident in Fukushima brought up new issues in the area of safety of nuclear reactors. Among others, Spent Fuel Pool accidents gained new focus. The computer codes applicable for safety analyses of Nuclear Power Plants have limited verification and validation in this area and their applicability remains still to be proven. An important phenomenon occurring during loss of water in SFP is air oxidation of Zircaloy cladding material. Mathematical modeling of this phenomenon in computer codes has been under development during the last years. This document presents a review of models for air oxidation of Zircaloy, including: up to date models available in open literature, as well as models available in computer codes: ASTEC, MELCOR, and SPECTRA. The models were tested by performing simulations of a number air oxidation experiments from ANL, KIT, and IRSN. As a result of this work, a recommended set of correlations, applicable for wide range of temperatures, including pre- and post-breakaway reaction, has been selected. For the pre-breakaway (parabolic) regime the correlation of Benjamin et al. (Sandia National Laboratories, Albuquerque, NM, 1979) was selected for the low temperatures and a new correlation has been proposed for the high temperatures. For the post-breakaway (linear) regime, Boase and Vandergraaf (Nucl. Technol., 1977;32:60–71) were selected for the low temperatures and a new correlation has been proposed for the high temperatures. Furthermore, a new model for the breakaway transition has been proposed. The correlation set is applicable for Zircaloy-4, for practically the entire temperature range. The recommended set provides an improved accuracy of results

  16. Evaluation of air cleaning technologies existing in the Danish market

    DEFF Research Database (Denmark)

    Ardkapan, Siamak Rahimi; Afshari, Alireza; Bergsøe, Niels Christian

    2014-01-01

    the ozone level significantly in the room. Moreover, they can cause generation of ultrafine particles and consequently increase ultrafine particle concentration in the room. The study suggests using a mechanical filter with low pressure drop as a recommended air cleaning technology in order to remove...

  17. Air Guard Unit Capitalizing on Leading-Edge Technology

    OpenAIRE

    Center for Homeland Defense and Security

    2012-01-01

    Center for Homeland Defense and Security, PRESS RELEASES When the California Air National Guard 129th Rescue Wing deploys next year to the Horn of Africa and Afghanistan, it plans to have a new, game-changing technology developed at the...

  18. Catalysts Promoted with Niobium Oxide for Air Pollution Abatement

    Directory of Open Access Journals (Sweden)

    Wendi Xiang

    2017-05-01

    Full Text Available Pt-containing catalysts are currently used commercially to catalyze the conversion of carbon monoxide (CO and hydrocarbon (HC pollutants from stationary chemical and petroleum plants. It is well known that Pt-containing catalysts are expensive and have limited availability. The goal of this research is to find alternative and less expensive catalysts to replace Pt for these applications. This study found that niobium oxide (Nb2O5, as a carrier or support for certain transition metal oxides, promotes oxidation activity while maintaining stability, making them candidates as alternatives to Pt. The present work reports that the orthorhombic structure of niobium oxide (formed at 800 °C in air promotes Co3O4 toward the oxidation of both CO and propane, which are common pollutants in volatile organic compound (VOC applications. This was a surprising result since this structure of Nb2O5 has a very low surface area (about 2 m2/g relative to the more traditional Al2O3 support, with a surface area of 150 m2/g. The results reported demonstrate that 1% Co3O4/Nb2O5 has comparable fresh and aged catalytic activity to 1% Pt/γ-Al2O3 and 1% Pt/Nb2O5. Furthermore, 6% Co3O4/Nb2O5 outperforms 1% Pt/Al2O3 in both catalytic activity and thermal stability. These results suggest a strong interaction between niobium oxide and the active component—cobalt oxide—likely by inducing an oxygen defect structure with oxygen vacancies leading to enhanced activity toward the oxidation of CO and propane.

  19. Oxide ultrathin films science and technology

    CERN Document Server

    Pacchioni, Gianfranco

    2012-01-01

    A wealth of information in one accessible book. Written by international experts from multidisciplinary fields, this in-depth exploration of oxide ultrathin films covers all aspects of these systems, starting with preparation and characterization, and going on to geometrical and electronic structure, as well as applications in current and future systems and devices. From the Contents: Synthesis and Preparation of Oxide Ultrathin FilmsCharacterization Tools of Oxide Ultrathin FilmsOrdered Oxide Nanostructures on Metal SurfacesUnusual Properties of Oxides and Other Insulators in the Ultrathin Li

  20. Kinetics of wet air oxidation (WAO) of alcaloide factory wastewater.

    Science.gov (United States)

    Kunukcu, Y Kaçar

    2005-01-01

    Wet air oxidation (WAO) of Afyon alcaloide factory wastewater, a typical high strength industrial wastewater, was carried out. The process was performed in a specifically designed titanium bubble reactor at temperatures in the range of 140-160 degrees C. The kinetics of WAO of alcaloide factory wastewater was modeled by assuming two distinct steps. The rates of destruction were measured with respect to reduction in COD. The oxidation reaction was found to be first order with respect to COD concentration and also second order with respect to oxygen concentration in both steps. The values of activation energies were found to be in the range of 4.93 x 10(4)-7.85 x 10(4) kJ/kmol.

  1. Catalytic wet air oxidation of high concentration pharmaceutical wastewater.

    Science.gov (United States)

    Zhan, Wei; Wang, Xiaocong; Li, Daosheng; Ren, Yongzheng; Liu, Dongqi; Kang, Jianxiong

    2013-01-01

    In this study, we investigated the pretreatment of a high concentration pharmaceutical wastewater by catalytic wet air oxidation (CWAO) process. Different experiments were conducted to investigate the effects of the catalyst type, operating temperature, initial system pH, and oxygen partial pressure on the oxidation of the wastewater. Results show that the catalysts prepared by the co-precipitation method have better catalytic activity compared to others. Chemical oxygen demand (COD) conversion increased with the increase in temperature from 160 to 220 °C and decreased with the increase in pH. Moreover, the effect of the oxygen partial pressure on the COD conversion was significant only during the first 20 min of the reaction. Furthermore, the biodegradability of the wastewater improved greatly after CWAO, the ratio of BOD5/COD increased less than 0.1-0.75 when treated at 220 °C (BOD: biochemical oxygen demand).

  2. NASA technology program for future civil air transports

    Science.gov (United States)

    Wright, H. T.

    1983-01-01

    An assessment is undertaken of the development status of technology, applicable to future civil air transport design, which is currently undergoing conceptual study or testing at NASA facilities. The NASA civil air transport effort emphasizes advanced aerodynamic computational capabilities, fuel-efficient engines, advanced turboprops, composite primary structure materials, advanced aerodynamic concepts in boundary layer laminarization and aircraft configuration, refined control, guidance and flight management systems, and the integration of all these design elements into optimal systems. Attention is given to such novel transport aircraft design concepts as forward swept wings, twin fuselages, sandwich composite structures, and swept blade propfans.

  3. Wet air oxidation of seedcorn wastes containing pesticides and insecticides

    Energy Technology Data Exchange (ETDEWEB)

    Sievers, M.; Schlaefer, O.; Onyeche, T.I.; Schroeder, C.; Bormann, H.; Schaefer, S. [CUTEC-Inst. GmbH (Clausthal Environment Technology Inst.), Clausthal-Zellerfeld (Germany)

    2003-07-01

    Wet air oxidation as an alternative treatment process to pyrolysis and combustion of seedcorn wastes was investigated in lab-scale experiments. Due to solid condition of the seed corn waste, the process has been adapted by repeated spraying of water on the seed corn bulk to avoid the production of sludge and its subsequent dewatering. Original seed corns from industrial production plants were used for a degradation kinetic study under smooth wet air oxidation conditions. The temperatures were between 80 and 150 C, the pressure from 1 to 4.5 bar and the pH at different values from 3 to 13. Degradation rates for five different compounds of pesticides and insecticides, namely Imidacloprid, Thiram, Hymexazol, Carbofuran and Tefluthrin were conducted. These compounds represent the recently used in agricultural seedcorn applications. The degradation rate depends linearly on temperature between 80 and 150 C. At 120 C the lowest degradation rate was found for Tefluthrin by 25 mg/h per L reaction volume while the highest degradation rate to be conducted was for Imidacloprid at 363 mg/h L. (orig.)

  4. Wet air oxidation of epoxy acrylate monomer industrial wastewater.

    Science.gov (United States)

    Yang, Shaoxia; Liu, Zhengqian; Huang, Xiaohui; Zhang, Beiping

    2010-06-15

    Epoxy acrylate monomer industrial wastewater contained highly concentrated and toxic organic compounds. The wet air oxidation (WAO) and catalytic wet air oxidation (CWAO) were used to eliminate pollutants in order to examine the feasibility of the WAO/CWAO as a pre-treatment method for the industrial wastewater. The results showed that in the WAO 63% chemical oxygen demand (COD) and 41% total organic carbon (TOC) removals were achieved and biological oxygen demand (BOD(5))/COD ratio increased from 0.13 to 0.72 after 3h reaction at 250 degrees C, 3.5MPa and the initial concentration of 100g(COD)/L. Among homogenous catalysts (Cu(2+), Fe(2+), Fe(3+) and Mn(2+) salts), Cu(2+) salt exhibited better performance. CuO catalyst was used in the CWAO of the wastewater, COD and TOC conversion were 77 and 54%, and good biodegradability was achieved. The results proved that the CWAO was an effective pre-treatment method for the epoxy acrylate monomer industrial wastewater.

  5. 40 CFR 50.4 - National primary ambient air quality standards for sulfur oxides (sulfur dioxide).

    Science.gov (United States)

    2010-07-01

    ... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS NATIONAL PRIMARY AND SECONDARY AMBIENT AIR QUALITY STANDARDS § 50.4 National primary ambient air quality standards for sulfur oxides (sulfur dioxide). Link to an... applicable to all areas notwithstanding the promulgation of SO2 national ambient air quality standards...

  6. Composition of air pollution particles modifies oxidative stress in cells, tissues, and living systems

    Science.gov (United States)

    Epidemiological studies demonstrate an association between increased levels of ambient air pollution particles and human morbidity and mortality. Production of oxidants, either directly by the air pollution particles or by the host response to the particles, appears to be fundame...

  7. 174 Reduction in Allergic Rhinitis Index by Decreasing Aero-Allergens and Malodor Causing Volatile Organic Compounds by Luna Air Purifiers Using Photo-Catalytic Oxidation (PCO) Technology

    OpenAIRE

    Ghosh, Nabarun; Aguaiza, Cristina; Guzman, Alicia; Chudasama, Jay; Bennert, Jeff; Das, A. B.

    2012-01-01

    Background The quality of the environment within buildings is a topic of major importance for public health. Breathing pure and clean air allows us to think more clearly, sleep more soundly, and stay healthier. Studies show that we receive 56% of our energy from the air we breathe, more than from water and food combined. On average we breathe 37 pounds of air a day. It has been established that the use of negative ions in a purification system is an effective means of eradicating aeroallergen...

  8. Wet air oxidation induced enhanced biodegradability of distillery effluent.

    Science.gov (United States)

    Malik, S N; Saratchandra, T; Tembhekar, P D; Padoley, K V; Mudliar, S L; Mudliar, S N

    2014-04-01

    The present study reports the feasibility of Wet Air Oxidation (WAO) as a pretreatment option for enhanced biodegradation of complex distillery effluent. Initially, the distillery effluent was pretreated by WAO at different process conditions (pressure, temperature and time) to facilitate enhancement in the biodegradability index (BI = BOD5: COD ratio). The biodegradability of WAO pretreated effluent was evaluated by subjecting it to aerobic biodegradation and anaerobic followed by aerobic biodegradation. Aerobic biodegradation of pretreated effluent with enhanced biodegradability index (BI = 0.4-0.8) showed enhanced COD reduction of up to 67.7%, whereas the untreated effluent (BI = 0.17) indicated poor COD reduction of only 22.5%. Anaerobic followed by aerobic biodegradation of pretreated effluent has shown up to 87.9% COD reduction, while the untreated effluent has shown only 43.1% COD reduction. Bio-kinetic parameters also confirmed the increased rate of bio-oxidation at enhanced BIs. The results indicate that the WAO pretreatment facilitates enhanced bio-oxidation/bio-degradation of complex effluents like the distillery spent wash.

  9. Overview of Compressed Air Energy Storage and Technology Development

    Directory of Open Access Journals (Sweden)

    Jidai Wang

    2017-07-01

    Full Text Available With the increase of power generation from renewable energy sources and due to their intermittent nature, the power grid is facing the great challenge in maintaining the power network stability and reliability. To address the challenge, one of the options is to detach the power generation from consumption via energy storage. The intention of this paper is to give an overview of the current technology developments in compressed air energy storage (CAES and the future direction of the technology development in this area. Compared with other energy storage technologies, CAES is proven to be a clean and sustainable type of energy storage with the unique features of high capacity and long-duration of the storage. Its scale and cost are similar to pumped hydroelectric storage (PHS, thus CAES has attracted much attention in recent years while further development for PHS is restricted by the availability of suitable geological locations. The paper presents the state-of-the-art of current CAES technology development, analyses the major technological barriers/weaknesses and proposes suggestions for future technology development. This paper should provide a useful reference for CAES technology research and development strategy.

  10. High Technology Centrifugal Compressor for Commercial Air Conditioning Systems

    Energy Technology Data Exchange (ETDEWEB)

    Ruckes, John

    2006-04-15

    R&D Dynamics, Bloomfield, CT in partnership with the State of Connecticut has been developing a high technology, oil-free, energy-efficient centrifugal compressor called CENVA for commercial air conditioning systems under a program funded by the US Department of Energy. The CENVA compressor applies the foil bearing technology used in all modern aircraft, civil and military, air conditioning systems. The CENVA compressor will enhance the efficiency of water and air cooled chillers, packaged roof top units, and other air conditioning systems by providing an 18% reduction in energy consumption in the unit capacity range of 25 to 350 tons of refrigeration The technical approach for CENVA involved the design and development of a high-speed, oil-free foil gas bearing-supported two-stage centrifugal compressor, CENVA encompassed the following high technologies, which are not currently utilized in commercial air conditioning systems: Foil gas bearings operating in HFC-134a; Efficient centrifugal impellers and diffusers; High speed motors and drives; and System integration of above technologies. Extensive design, development and testing efforts were carried out. Significant accomplishments achieved under this program are: (1) A total of 26 builds and over 200 tests were successfully completed with successively improved designs; (2) Use of foil gas bearings in refrigerant R134a was successfully proven; (3) A high speed, high power permanent magnet motor was developed; (4) An encoder was used for signal feedback between motor and controller. Due to temperature limitations of the encoder, the compressor could not operate at higher speed and in turn at higher pressure. In order to alleviate this problem a unique sensorless controller was developed; (5) This controller has successfully been tested as stand alone; however, it has not yet been integrated and tested as a system; (6) The compressor successfully operated at water cooled condensing temperatures Due to temperature

  11. Advanced oxidation technologies : photocatalytic treatment of wastewater

    OpenAIRE

    Chen, J.

    1997-01-01

    7.1. Summary and conclusions

    The last two decennia have shown a growing interest in the photocatalytic treatment of wastewater, and more and more research has been carried out into the various aspects of photocatalysis, varying from highly fundamental aspects to practical application. However, despite all this research, there is still much to investigate. Suggested photocatalytic mechanisms, such as those for oxidation by hydroxyl radicals and for oxidation at the surface of photocata...

  12. Catalytic wet air oxidation with Ni- and Fe-doped mixed oxides derived from hydrotalcites.

    Science.gov (United States)

    Ovejero, G; Rodríguez, A; Vallet, A; Gómez, P; García, J

    2011-01-01

    Catalytic wet air oxidation of Basic Yellow 11 (BY11), a basic dye, was studied in a batch reactor. Layered double hydroxides with the hydrotalcite-like structure containing nickel or iron cations have been prepared by coprecipitation and subsequently calcined leading to Ni- and Fe-doped mixed oxides, respectively. Compared with the results in the wet air oxidation of BY11, these catalysts showed high activity for total organic carbon (TOC), toxicity and dye removal at 120 degrees C and 50 bars after 120 min. It has been demonstrated that the activity depended strongly on the presence of catalyst. The results show that catalysts containing nickel provide a higher extent of oxidation of the dye whereas the reaction carried out with the iron catalyst is faster. The Ni and Fe dispersion determined from the TPR results was higher for the catalysts with a lower Ni or Fe content and decreased for higher Ni or Fe contents. On the basis of activity and selectivity, the Ni containing catalyst with the medium (3%) Ni content was found to be the best catalyst. Finally, a relationship between metal content of the catalyst and reaction rate has been established.

  13. Degradation of paracetamol by catalytic wet air oxidation and sequential adsorption - Catalytic wet air oxidation on activated carbons

    Energy Technology Data Exchange (ETDEWEB)

    Quesada-Penate, I. [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, 4, Allee Emile Monso, F-31432 Toulouse (France); CNRS, Laboratoire de Genie Chimique, F-31432 Toulouse (France); Julcour-Lebigue, C., E-mail: carine.julcour@ensiacet.fr [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, 4, Allee Emile Monso, F-31432 Toulouse (France); CNRS, Laboratoire de Genie Chimique, F-31432 Toulouse (France); Jauregui-Haza, U.J. [Instituto Superior de Tecnologias y Ciencias Aplicadas, Ave. Salvador Allende y Luaces, Habana (Cuba); Wilhelm, A.M.; Delmas, H. [Universite de Toulouse, INPT, UPS, Laboratoire de Genie Chimique, 4, Allee Emile Monso, F-31432 Toulouse (France); CNRS, Laboratoire de Genie Chimique, F-31432 Toulouse (France)

    2012-06-30

    Highlights: Black-Right-Pointing-Pointer Three activated carbons (AC) compared as adsorbents and oxidation catalysts. Black-Right-Pointing-Pointer Similar evolution for catalytic and adsorptive properties of AC over reuses. Black-Right-Pointing-Pointer Acidic and mesoporous AC to be preferred, despite lower initial efficiency. Black-Right-Pointing-Pointer Oxidative degradation of paracetamol improves biodegradability. Black-Right-Pointing-Pointer Convenient hybrid adsorption-regenerative oxidation process for continuous treatment. - Abstract: The concern about the fate of pharmaceutical products has raised owing to the increasing contamination of rivers, lakes and groundwater. The aim of this paper is to evaluate two different processes for paracetamol removal. The catalytic wet air oxidation (CWAO) of paracetamol on activated carbon was investigated both as a water treatment technique using an autoclave reactor and as a regenerative treatment of the carbon after adsorption in a sequential fixed bed process. Three activated carbons (ACs) from different source materials were used as catalysts: two microporous basic ACs (S23 and C1) and a meso- and micro-porous acidic one (L27). During the first CWAO experiment the adsorption capacity and catalytic performance of fresh S23 and C1 were higher than those of fresh L27 despite its higher surface area. This situation changed after AC reuse, as finally L27 gave the best results after five CWAO cycles. Respirometry tests with activated sludge revealed that in the studied conditions the use of CWAO enhanced the aerobic biodegradability of the effluent. In the ADOX process L27 also showed better oxidation performances and regeneration efficiency. This different ageing was examined through AC physico-chemical properties.

  14. Graphene oxide as an effective catalyst for wet air oxidation of phenol.

    Science.gov (United States)

    Yang, Shaoxia; Cui, Yuhong; Sun, Yu; Yang, Hongwei

    2014-09-15

    The graphene oxide (GO) and chemically reduced graphene oxides, used as catalysts in absence of any metals, were investigated in the catalytic wet air oxidation (CWAO) of phenol in a batch reactor. The characterization of the materials was measured with scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman, fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The carbon materials exhibited good phenol and total organic compounds (TOC) removals in the CWAO of phenol. The GO had the highest catalytic activity, total phenol removal was achieved after 40 min, and ca. 84% TOC removal was obtained after 120 min at reaction temperature of 155°C, total pressure of 2.5 MPa and catalyst loading of 0.2 gL(-1).

  15. History of the technological development of air conduction hearing aids.

    Science.gov (United States)

    Mudry, A; Dodelé, L

    2000-06-01

    This was a study of the history of the technological development of air conduction hearing aids, and a review of international literature on the subject. The technological evolution of amplification devices, from their origin to the present day, can be divided into seven distinct periods: the period of sound collectors, the period of hearing devices constructed from carbon, the period of vacuum tubes, the transistor period, the period of integrated circuits, the microprocessor period and the period of digital hearing instruments. Throughout these different stages, hearing instruments have progressively developed reaching their present state. The current era is itself undergoing constant development and change. With the introduction of new technologies, we expect that the rate of change will increase rapidly in the future.

  16. Homogeneous catalytic wet air oxidation for the treatment oftextile wastewaters

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    An extensive series of experiments was carried out in order to identify suitable catalysts to boost the reaction rate of wet air oxidation of real textile wastewaters at relatively mild temperature and pressure. Experimental results indicated that all catalysts tested in this investigation had shown an impressive increase in the initial COD and TOC removal rate as well as the COD and TOC removal levels in two hours reaction. Among all the catalysts tested, copper salts were more effective than the rest. Anions of the salt soluffonsalso played a role in the catalytic process with nitrate ions having better effect than sulfate ions. Hence copper nitrates were more effective than copper sulfates. It was also found that a mixture of salts with different metals performed better than either of the component single salt alone.

  17. Air trichloroethylene oxidation in a corona plasma-catalytic reactor

    Science.gov (United States)

    Masoomi-Godarzi, S.; Ranji-Burachaloo, H.; Khodadadi, A. A.; Vesali-Naseh, M.; Mortazavi, Y.

    2014-08-01

    The oxidative decomposition of trichloroethylene (TCE; 300 ppm) by non-thermal corona plasma was investigated in dry air at atmospheric pressure and room temperature, both in the absence and presence of catalysts including MnOx, CoOx. The catalysts were synthesized by a co-precipitation method. The morphology and structure of the catalysts were characterized by BET surface area measurement and Fourier Transform Infrared (FTIR) methods. Decomposition of TCE and distribution of products were evaluated by a gas chromatograph (GC) and an FTIR. In the absence of the catalyst, TCE removal is increased with increases in the applied voltage and current intensity. Higher TCE removal and CO2 selectivity is observed in presence of the corona and catalysts, as compared to those with the plasma alone. The results show that MnOx and CoOx catalysts can dissociate the in-plasma produced ozone to oxygen radicals, which enhances the TCE decomposition.

  18. Identification of Iron Oxides Qualitatively/Quantitatively Formed during the High Temperature Oxidation of Superalloys in Air and Steam Environments

    Institute of Scientific and Technical Information of China (English)

    M.Siddique; N.Hussain; M.Shafi

    2009-01-01

    Mossbauer spectroscopy has been used to study the morphology of iron oxides formed during the oxidation of superalloys, such as SS-304L (1.4306S), Incoloy-800H, Incoloy-825, UBHA-25L, Sanicro-28 and Inconel-690, at 1200℃ exposed in air and steam environments for 400 h. The basic aim was to identify and compare the iron oxides qualitatively and quantitatively, formed during the oxidation of these alloys in two environments. The behaviour of alloy UBHA-25L in high temperature oxidation in both environments indicates that it has good oxidation resistance especially in steam, whereas Sanicro-28 has excellent corrosion resistance in steam environment. In air oxidation of lnconel-690 no iron oxide, with established Mossbauer parameters, was detected.

  19. Palladium-catalyzed air-based oxidative coupling of arylboronic acids with H-phosphine oxides leading to aryl phosphine oxides.

    Science.gov (United States)

    Fu, Tingting; Qiao, Hongwei; Peng, Zhimin; Hu, Gaobo; Wu, Xueji; Gao, Yuxing; Zhao, Yufen

    2014-05-14

    We present a novel and highly efficient methodology that allows for the construction of C-P bonds via the palladium-catalyzed air-based oxidative coupling of various commercially available arylboronic acids with easily oxidized H-phosphine oxides leading to valuable aryl phosphine oxides, particularly triarylphosphine oxides, with the use of air as the green oxidant, broad substrate applicability and good to excellent yields. The described catalytic system should be an efficient complement to the Chan-Lam type reaction and be useful in synthetic programs.

  20. National Security Science and Technology Initiative: Air Cargo Screening

    Energy Technology Data Exchange (ETDEWEB)

    Bingham, Philip R [ORNL; White, Tim [Pacific Northwest National Laboratory (PNNL); Cespedes, Ernesto [Idaho National Laboratory (INL); Bowerman, Biays [Brookhaven National Laboratory (BNL); Bush, John [Battelle

    2010-11-01

    The non-intrusive inspection (NII) of consolidated air cargo carried on commercial passenger aircraft continues to be a technically challenging, high-priority requirement of the Department of Homeland Security's Science and Technology Directorate (DHS S&T), the Transportation Security Agency and the Federal Aviation Administration. The goal of deploying a screening system that can reliably and cost-effectively detect explosive threats in consolidated cargo without adversely affecting the flow of commerce will require significant technical advances that will take years to develop. To address this critical National Security need, the Battelle Memorial Institute (Battelle), under a Cooperative Research and Development Agreement (CRADA) with four of its associated US Department of Energy (DOE) National Laboratories (Oak Ridge, Pacific Northwest, Idaho, and Brookhaven), conducted a research and development initiative focused on identifying, evaluating, and integrating technologies for screening consolidated air cargo for the presence of explosive threats. Battelle invested $8.5M of internal research and development funds during fiscal years 2007 through 2009. The primary results of this effort are described in this document and can be summarized as follows: (1) Completed a gap analysis that identified threat signatures and observables, candidate technologies for detection, their current state of development, and provided recommendations for improvements to meet air cargo screening requirements. (2) Defined a Commodity/Threat/Detection matrix that focuses modeling and experimental efforts, identifies technology gaps and game-changing opportunities, and provides a means of summarizing current and emerging capabilities. (3) Defined key properties (e.g., elemental composition, average density, effective atomic weight) for basic commodity and explosive benchmarks, developed virtual models of the physical distributions (pallets) of three commodity types and three

  1. National Security Science and Technology Initiative: Air Cargo Screening

    Energy Technology Data Exchange (ETDEWEB)

    Bingham, Philip R [ORNL; White, Tim [Pacific Northwest National Laboratory (PNNL); Cespedes, Ernesto [Idaho National Laboratory (INL); Bowerman, Biays [Brookhaven National Laboratory (BNL); Bush, John [Battelle

    2010-11-01

    The non-intrusive inspection (NII) of consolidated air cargo carried on commercial passenger aircraft continues to be a technically challenging, high-priority requirement of the Department of Homeland Security's Science and Technology Directorate (DHS S&T), the Transportation Security Agency and the Federal Aviation Administration. The goal of deploying a screening system that can reliably and cost-effectively detect explosive threats in consolidated cargo without adversely affecting the flow of commerce will require significant technical advances that will take years to develop. To address this critical National Security need, the Battelle Memorial Institute (Battelle), under a Cooperative Research and Development Agreement (CRADA) with four of its associated US Department of Energy (DOE) National Laboratories (Oak Ridge, Pacific Northwest, Idaho, and Brookhaven), conducted a research and development initiative focused on identifying, evaluating, and integrating technologies for screening consolidated air cargo for the presence of explosive threats. Battelle invested $8.5M of internal research and development funds during fiscal years 2007 through 2009. The primary results of this effort are described in this document and can be summarized as follows: (1) Completed a gap analysis that identified threat signatures and observables, candidate technologies for detection, their current state of development, and provided recommendations for improvements to meet air cargo screening requirements. (2) Defined a Commodity/Threat/Detection matrix that focuses modeling and experimental efforts, identifies technology gaps and game-changing opportunities, and provides a means of summarizing current and emerging capabilities. (3) Defined key properties (e.g., elemental composition, average density, effective atomic weight) for basic commodity and explosive benchmarks, developed virtual models of the physical distributions (pallets) of three commodity types and three

  2. Kinetics of the oxidation of Zn foils in air atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Baca, R; Martinez, J [Centro de Investigacion de Dispositivos Semiconductores, BUAP, Puebla. C.P. 72570 (Mexico); Kryshtab, T [Departamento de Ciencias de Materiales, ESFM - IPN, Mexico D.F (Mexico); Juarez, G; Solache, H; Andraca, J; Garcia, O; Pena-Sierra, R, E-mail: rbaca02006@yahoo.com.mx

    2010-02-15

    The formation kinetics of ZnO thin films grown by oxidation of polycrystalline Zn foils in air atmosphere at temperatures below the melting point is reported. Previous to the oxidation process the Zn foils were polished to produce mirror-like finished surfaces. The growth rate of the ZnO films was monitored by ellipsometric measurements. The growth rate of the ZnO films under 100 nm follows a linear and parabolic behavior in accordance with previously reported studies. The thicknesses of the films strongly influence the appearance of the final produced ZnO surface. The ZnO films surfaces with thicknesses less than 100 nm resulted uniform with low rms roughness. However as the films become thicker the rms roughness increased and a uniform distribution of whiskers was observed. X-ray diffraction and photoluminescence (PL) studies were done on the ZnO films to find out their structural and optical characteristics. PL spectra on the films are composed by two main bands; a weak near-band gap in the ultraviolet region and a strong but well defined green band. A discussion is included on the origins of the observed PL spectra.

  3. Oscillatory oxidation of benzaldehyde by air. 1. Experimental observations

    Energy Technology Data Exchange (ETDEWEB)

    Colussi, A.J.; Ghibaudi, E.; Yuan, Zhi; Noyes, R.M. (Univ. of Oregon, Eugene (USA))

    1990-11-21

    In 90% aqueous acetic acid at 70 C, the oxidation of benzaldehyde to benzoic acid by air is catalyzed by a mixture of cobalt(II) and bromide. Jensen has shown that the concentration of cobalt(III) undergoes major oscillations during the reaction. Consistent with these prior observations, the authors find that the rate of formation of cobalt(III) increases exponentially until at about 10{sup {minus}5} M s{sup {minus}1} it becomes comparable to the maximum rate at which O{sub 2} can be transported from atmosphere to solution. A virtually discontinuous change of behavior then causes the concentration of cobalt(III) to decrease at about 10{sup {minus}4} M s{sup {minus}1}; the rate of this decrease is almost constant and independent of (Co{sup III}) until most of this species has been consumed. The authors have examined most of the subsystems that they could prepare and study independently. Among other observations, they find that increasing acidity increases the rate at which bromide catalyzes the oxidation of benzaldehyde by cobalt(III).

  4. Copper on activated carbon for catalytic wet air oxidation

    Directory of Open Access Journals (Sweden)

    Nora Dolores Martínez

    2009-03-01

    Full Text Available Textile industry is an important source of water contamination. Some of the organic contaminants cannot be eliminated by nature in a reasonable period. Heterogeneous catalytic wet air oxidation is one of the most effective methods to purify wastewater with organic contaminants. In this work, catalysts based on copper supported on activated carbon were synthesized. The activated carbons were obtained from industrial wastes (apricot core and grape stalk of San Juan, Argentina. These were impregnated with a copper salt and thermically treated in an inert atmosphere. Analysis of specific surface, pore volume, p zc, acidity, basicity and XRD patterns were made in order to characterize the catalysts. The catalytic activity was tested in the oxidation of methylene blue (MB and polyvinyl alcohol (PVA in aqueous phase with pure oxygen. Reaction tests were carried out in a Parr batch reactor at different temperatures, with a 0.2 MPa partial pressure of oxygen. The amount of unconverted organics was measured by spectrophotometry. Higher temperatures were necessary for the degradation of PVA compared to those for methylene blue.

  5. Catalytic wet air oxidation for the treatment of emulsifying wastewater

    Institute of Scientific and Technical Information of China (English)

    ZHAO Jian-fu; CHEN Ling; LU Yi-cheng; TANG Wen-wei

    2005-01-01

    The wet air oxidation (WAO) and catalytic WAO (CWAO) of the high strength emulsifying wastewater containing nonionic surfactants have been investigated in terms of COD and TOC removal. The WAO and homogeneous CWAO processes were carried out at the temperature from 433 K to 513 K, with initial oxygen pressure 1.2 MPa. It was found that homogeneous catalyst copper(Cu ( NO3 )2 )had an fairly good catalytic activity for the WAO process, and the oxidation was catalyzed when the temperature was higher than 473 K.Moreover, several heterogeneous catalysts were proved to be effective for the WAO process. At the temperature 473 K, after 2 h reaction,WAO process could achieve about 75% COD removal and 66% TOC removal, while catalysts Cu/Al2O3 and Mn-Ce/Al2O3 elevated the COD removal up to 86%-89% and that of TOC up to 82%. However, complete elimination of COD and TOC was proved to be difficult even the best non-noble catalyst was used. Therefore, the effluent from WAO or CWAO process need to be further disposed. The bioassay proved that the effluent from WAO process was amenable to the biochemical method.

  6. Kinetics study on catalytic wet air oxidation of phenol by several metal oxide catalysts

    Institute of Scientific and Technical Information of China (English)

    WAN Jia-feng; FENG Yu-jie; CAI Wei-min; YANG Shao-xia; SUN Xiao-jun

    2004-01-01

    Four metal oxide catalysts composed of copper (Cu), stannum (Sn), copper-stannum (Cu-Sn) and copper-cerium(Cu-Ce) respectively were prepared by the co-impregnation method, and γ-alumina(γ-Al2O3) is selected as support. A first-order kinetics model was established to study the catalytic wet air oxidation of phenol at different temperature when these catalysts were used. The model simulations are good agreement with present experimental data. Results showed that the reaction rate constants can be significantly increased when catalysts were used, and the catalyst of 6% Cu-10%Ce/γ-Al2O3 showed the best catalytic activity. This is consistent with the result of catalytic wet air oxidation of phenol and the COD removal can be arrived at 98.2% at temperature 210℃, oxygen partial pressure 3 MPa and reaction time 30 min. The activation energies of each reaction with different catalysts are nearly equal, which is found to be about 42 kJ/mol and the reaction in this study is proved to be kinetics control.

  7. Nitric oxide in exhaled and aspirated nasal air as an objective measure of human response to isopropanol oxidation products and pthtalate esters in indoor air

    DEFF Research Database (Denmark)

    Lagercrantz, Love Per; Famula, Basia; Sundell, Jan

    2005-01-01

    The use of Nitric Oxide (NO) concentration in exhaled and aspirated nasal air to assess human response to indoor air pollution was tested in a climate chamber exposure experiment. The concentration of NO was measured using a chemiluminescence NO analyser. Sixteen healthy female subjects were expo...

  8. Two-dimensional oxides: multifunctional materials for advanced technologies.

    Science.gov (United States)

    Pacchioni, Gianfranco

    2012-08-13

    The last decade has seen spectacular progress in the design, preparation, and characterization down to the atomic scale of oxide ultrathin films of few nanometers thickness grown on a different material. This has paved the way towards several sophisticated applications in advanced technologies. By playing around with the low-dimensionality of the oxide layer, which sometimes leads to truly two-dimensional systems, one can exploit new properties and functionalities that are not present in the corresponding bulk materials or thick films. In this review we provide some clues about the most recent advances in the design of these systems based on modern electronic structure theory and on their preparation and characterization with specifically developed growth techniques and analytical methods. We show how two-dimensional oxides can be used in mature technologies by providing added value to existing materials, or in new technologies based on completely new paradigms. The fields in which two-dimensional oxides are used are classified based on the properties that are exploited, chemical or physical. With respect to chemical properties we discuss use of oxide ultrathin films in catalysis, solid oxide fuel cells, gas sensors, corrosion protection, and biocompatible materials; regarding the physical properties we discuss metal-oxide field effect transistors and memristors, spintronic devices, ferroelectrics and thermoelectrics, and solar energy materials. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. SBIR Advanced Technologies in Aviation and Air Transportation System 2016

    Science.gov (United States)

    Nguyen, Hung D.; Steele, Gynelle C.; Kaszeta, Richard W.; Gold, Calman; Corke, Thomas C.; McGowan, Ryan; Matlis, Eric; Eichenlaub, Jesse; Davis, Joshua T.; Shah, Parthiv N.

    2017-01-01

    This report is intended to provide a broad knowledge of various topics associated with NASA's Aeronautics Research Mission Directorate (ARMD), with particular interest on the NASA SBIR contracts awarded from 2011-2012 executed by small companies. The content of this report focuses on the high-quality, cutting-edge research that will lead to revolutionary concepts, technologies, and capabilities that enable radical change to both the airspace system and the aircraft that fly within it, facilitating a safer, more environmentally friendly, and more efficient air transportation system.

  10. Oxidation behavior of U-Si compounds in air from 25 to 1000 C

    Science.gov (United States)

    Sooby Wood, E.; White, J. T.; Nelson, A. T.

    2017-02-01

    The air oxidation behavior of U3Si2, USi, and U3Si5 is studied from room temperature to 1000 C. The onsets of breakaway oxidation for each compound are identified during synthetic air ramps to 1000 C using thermogravimetric analysis. Isothermal air oxidation tests are performed below and above the breakaway oxidation onset to discern the oxidation kinetic behavior of these candidate accident tolerant fuel forms. Uranium metal is tested in the same manner to provide a reference for the oxidation behavior. Thermogravimetric, x-ray diffraction, and scanning electron microscopy analysis are presented here along with a discussion of the oxidation behavior of these materials and the impact of the lack of oxidation resistance to their deployment as accident tolerant nuclear fuels.

  11. Analysis of Chemical Reaction Kinetics Behavior of Nitrogen Oxide During Air-staged Combustion in Pulverized Boiler

    Directory of Open Access Journals (Sweden)

    Jun-Xia Zhang

    2016-03-01

    Full Text Available Because the air-staged combustion technology is one of the key technologies with low investment running costs and high emission reduction efficiency for the pulverized boiler, it is important to reveal the chemical reaction kinetics mechanism for developing various technologies of nitrogen oxide reduction emissions. At the present work, a three-dimensional mesh model of the large-scale four corner tangentially fired boiler furnace is established with the GAMBIT pre-processing of the FLUENT software. The partial turbulent premixed and diffusion flame was simulated for the air-staged combustion processing. Parameters distributions for the air-staged and no the air-staged were obtained, including in-furnace flow field, temperature field and nitrogen oxide concentration field. The results show that the air-staged has more regular velocity field, higher velocity of flue gas, higher turbulence intensity and more uniform temperature of flue gas. In addition, a lower negative pressure zone and lower O2 concentration zone is formed in the main combustion zone, which is conducive to the NO of fuel type reduced to N2, enhanced the effect of NOx reduction. Copyright © 2016 BCREC GROUP. All rights reserved Received: 5th November 2015; Revised: 14th January 2016; Accepted: 16th January 2016  How to Cite: Zhang, J.X., Zhang, J.F. (2016. Analysis of Chemical Reaction Kinetics Behavior of Nitrogen Oxide During Air-staged Combustion in Pulverized Boiler. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (1: 100-108. (doi:10.9767/bcrec.11.1.431.100-108 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.11.1.431.100-108

  12. Wet air and catalytic wet air oxidation of several azodyes from wastewaters: the beneficial role of catalysis.

    Science.gov (United States)

    Rodríguez, A; García, J; Ovejero, G; Mestanza, M

    2009-01-01

    Degradation of several azo dyes, Acid Orange 7 (AO7), Acid Orange 74 (AO74), Direct Blue 71 (DB71), Reactive Black 5 (RB5) and Eriochrome Blue Black B (EBBB), well-known non-biodegradable mono, di and tri azo dyes has been studied using, wet-air oxidation (WAO) and catalytic wet air oxidation (CWAO). The efficiency of substrate decolorization and mineralization in each process has been comparatively discussed by evolution concentration, chemical oxygen demand, total organic carbon content and toxicity of dyes solutions. The most efficient method on decolorization and mineralization (TOC) was observed to be CWAO process. Mineralization efficiency with wet air and catalytic wet air oxidation essays was observed in the order of mono-azo > di-azo > tri-azo dye. Final solutions of CWAO applications after 180 min treatment can be disposed safely to environment.

  13. Evaluation of a Combined Ultraviolet Photocatalytic Oxidation(UVPCO)/Chemisorbent Air Cleaner for Indoor Air Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, Alfred T.; Destaillats, Hugo; Hotchi, Toshifumi; Fisk,William J.

    2007-02-01

    We previously reported that gas-phase byproducts of incomplete oxidation were generated when a prototype ultraviolet photocatalytic oxidation (UVPCO) air cleaner was operated in the laboratory with indoor-relevant mixtures of VOCs at realistic concentrations. Under these conditions, there was net production of formaldehyde and acetaldehyde, two important indoor air toxicants. Here, we further explore the issue of byproduct generation. Using the same UVPCO air cleaner, we conducted experiments to identify common VOCs that lead to the production of formaldehyde and acetaldehyde and to quantify their production rates. We sought to reduce the production of formaldehyde and acetaldehyde to acceptable levels by employing different chemisorbent scrubbers downstream of the UVPCO device. Additionally, we made preliminary measurements to estimate the capacity and expected lifetime of the chemisorbent media. For most experiments, the system was operated at 680-780 m{sup 3}/h (400-460 cfm). A set of experiments was conducted with common VOCs introduced into the UVPCO device individually and in mixture. Compound conversion efficiencies and the production of formaldehyde and acetaldehyde were determined by comparison of compound concentrations upstream and downstream of the reactor. There was general agreement between compound conversions efficiencies determined individually and in the mixture. This suggests that competition among compounds for active sites on the photocatalyst surface will not limit the performance of the UVPCO device when the total VOC concentration is low. A possible exception was the very volatile alcohols, for which there were some indications of competitive adsorption. The results also showed that formaldehyde was produced from many commonly encountered VOCs, while acetaldehyde was generated by specific VOCs, particularly ethanol. The implication is that formaldehyde concentrations are likely to increase when an effective UVPCO air cleaner is used in

  14. Degradation of paracetamol by catalytic wet air oxidation and sequential adsorption - Catalytic wet air oxidation on activated carbons.

    Science.gov (United States)

    Quesada-Peñate, I; Julcour-Lebigue, C; Jáuregui-Haza, U J; Wilhelm, A M; Delmas, H

    2012-06-30

    The concern about the fate of pharmaceutical products has raised owing to the increasing contamination of rivers, lakes and groundwater. The aim of this paper is to evaluate two different processes for paracetamol removal. The catalytic wet air oxidation (CWAO) of paracetamol on activated carbon was investigated both as a water treatment technique using an autoclave reactor and as a regenerative treatment of the carbon after adsorption in a sequential fixed bed process. Three activated carbons (ACs) from different source materials were used as catalysts: two microporous basic ACs (S23 and C1) and a meso- and micro-porous acidic one (L27). During the first CWAO experiment the adsorption capacity and catalytic performance of fresh S23 and C1 were higher than those of fresh L27 despite its higher surface area. This situation changed after AC reuse, as finally L27 gave the best results after five CWAO cycles. Respirometry tests with activated sludge revealed that in the studied conditions the use of CWAO enhanced the aerobic biodegradability of the effluent. In the ADOX process L27 also showed better oxidation performances and regeneration efficiency. This different ageing was examined through AC physico-chemical properties.

  15. The Study of LeachateTreatment by Using Three Advanced Oxidation Process Based Wet air Oxidation

    Directory of Open Access Journals (Sweden)

    Behroz Karimi

    2013-01-01

    Full Text Available Wet air oxidation is regarded as appropriate options for wastewater treatment with average organic compounds. The general purpose of this research is to determine the efficiency of three wet air oxidation methods, wet oxidation with hydrogen peroxide and absorption with activated carbon in removing organic matter and nitrogenous compounds from Isfahan's urban leachate. A leachate sample with the volume of 1.5 liters entered into a steel reactor with the volume of three liters and was put under a 10-bar pressure, at temperatures of 100, 200, and 300[degree sign] as well as three retention times of 30, 60, and 90 minutes. The sample was placed at 18 stages of leachate storage ponds in Isfahan Compost Plant with the volume of 20 liters, using three WPO, WAO methods and a combination of WAO/GAC for leachate pre-treatment. Thirty percent of pure oxygen and hydrogen peroxide were applied as oxidation agents. The COD removal efficiency in WAO method is 7.8-33.3%, in BOD is 14.7-50.6%, the maximum removal percentage (efficiency for NH4-N is 53.3% and for NO3-N is 56.4-73.9%. The removal efficiency of COD and BOD5 is 4.6%-34 and 24%-50 respectively in WPO method. Adding GAC to the reactor, the removal efficiency of all parameters was improved. The maximum removal efficiency was increased 48% for COD, 31%-43.6 for BOD5 by a combinational method, and the ratio of BOD5/COD was also increased to 90%. In this paper, WAO and WPO process was used for Leachate pre-treatment and WAO/GAC combinational process was applied for improving the organic matter removal and leachate treatment; it was also determined that the recent process is much more efficient in removing resistant organic matter.

  16. The study of leachate treatment by using three advanced oxidation process based wet air oxidation.

    Science.gov (United States)

    Karimi, Behroz; Ehrampoush, Mohammad Hassan; Ebrahimi, Asghar; Mokhtari, Mehdi

    2013-01-02

    Wet air oxidation is regarded as appropriate options for wastewater treatment with average organic compounds. The general purpose of this research is to determine the efficiency of three wet air oxidation methods, wet oxidation with hydrogen peroxide and absorption with activated carbon in removing organic matter and nitrogenous compounds from Isfahan's urban leachate. A leachate sample with the volume of 1.5 liters entered into a steel reactor with the volume of three liters and was put under a 10-bar pressure, at temperatures of 100, 200, and 300° as well as three retention times of 30, 60, and 90 minutes. The sample was placed at 18 stages of leachate storage ponds in Isfahan Compost Plant with the volume of 20 liters, using three WPO, WAO methods and a combination of WAO/GAC for leachate pre-treatment. Thirty percent of pure oxygen and hydrogen peroxide were applied as oxidation agents. The COD removal efficiency in WAO method is 7.8-33.3%, in BOD is 14.7-50.6%, the maximum removal percentage (efficiency) for NH4-N is 53.3% and for NO3-N is 56.4-73.9%. The removal efficiency of COD and BOD5 is 4.6%-34 and 24%-50 respectively in WPO method. Adding GAC to the reactor, the removal efficiency of all parameters was improved. The maximum removal efficiency was increased 48% for COD, 31%-43.6 for BOD5 by a combinational method, and the ratio of BOD5/COD was also increased to 90%. In this paper, WAO and WPO process was used for Leachate pre-treatment and WAO/GAC combinational process was applied for improving the organic matter removal and leachate treatment; it was also determined that the recent process is much more efficient in removing resistant organic matter.

  17. Electrochemical characterization of Fe-air rechargeable oxide battery in planar solid oxide cell stacks

    Science.gov (United States)

    Fang, Qingping; Berger, Cornelius M.; Menzler, Norbert H.; Bram, Martin; Blum, Ludger

    2016-12-01

    Iron-air rechargeable oxide batteries (ROB) comprising solid oxide cells (SOC) as energy converters and Fe/metal-oxide redox couples were characterized using planar SOC stacks. The charge and discharge of the battery correspond to the operations in the electrolysis and fuel cell modes, respectively, but with a stagnant atmosphere consisting of hydrogen and steam. A novel method was employed to establish the stagnant atmosphere for battery testing during normal SOC operation without complicated modification to the test bench and stack/battery concept. Manipulation of the gas compositions during battery operation was not necessary, but the influence of the leakage current from the testing system had to be considered. Batteries incorporating Fe2O3/8YSZ, Fe2O3/CaO and Fe2O3/ZrO2 storage materials were characterized at 800 °C. A maximum charge capacity of 30.4 Ah per layer (with an 80 cm2 active cell area) with ∼0.5 mol Fe was reached with a current of 12 A. The charge capacity lost 11% after ∼130 ROB cycles due to the increased agglomeration of active materials and formation of a dense oxide layer on the surface. The round trip efficiencies of the tested batteries were ≤84% due to the large internal resistance. With state-of-the-art cells, the round trip efficiency can be further improved.

  18. Energy-efficient air pollution controls for fossil-fueled plants: Technology assessment

    Energy Technology Data Exchange (ETDEWEB)

    Sayer, J.H.

    1995-06-01

    The 1990 Clean Air Act Amendments require most fossil-fuel fired power plants to reduce sulfur dioxide, nitrogen oxides, and particulate emissions. While emission-control equipment is available to help most of New York State`s 91 utility units in 31 power plants comply with the new regulations, technologies currently available consume energy, increase carbon dioxide emissions, reduce operating efficiency, and may produce large amounts of solid and/or semisolid byproducts that use additional energy for processing and disposal. This report discribes several pollution-control technologies that are more energy efficient compared to traditional technologies for controlling sulfur dioxide, nitrogen oxide, and particulates, that may have application in New York State. These technologies are either in commercial use, under development, or in the demonstration phase; This report also presents operating characteristics for these technologies and discusses solutions to dispose of pollution-control system byproducts. Estimated energy consumption for emission-control systems relative to a plant`s gross generating capacity is 3 to 5 for reducing up to 90% sulfur dioxide emissions from coal-fired plants. 0.5 to 2.5% for reducing nitrogen oxide emissions by up to 80% from all fossil-fuel fired plants; and 0.5 to 1.5 % for controlling particulate emissions from oil- and coal-fired plants. While fuel switching and/or cofiring with natural gas are options to reduce emissions, these techniques are not considered in this report; the discussion is limited to fossil-fueled steam-generating plants.

  19. Fe-Oxides in Water Remediation Technologies

    Science.gov (United States)

    Vaclavikova, M.; Stefusova, K.; Gallios, G. P.

    Water is essential for life, a strategic resource for every country and population. Its availability and sanitary safety is highly connected with the health and economic status of a population. The burden of disease due to polluted water is a major public health problem throughout the world. Many pollutants in water streams have been identified as toxic and harmful to the environment and human health, and among them arsenic, mercury and cadmium are considered those with the highest priority. Iron is the fourth most abundant element in the Earth's crust, and reactions involving iron play a major role in the environmental cycling of a range of important contaminants. Our earlier research has shown that Fe oxides/oxyhydroxides are particularly effective adsorbents of a range of contaminants (toxic metals), due to their high (reactive) specific surface area. It has been proven that Fe is particularly effective in As removal as a chemical bond is created on Fe surface and As is stabilised and can be safely deposited. Removal of contaminants from waste streams through precipitation with (hydrous) ferric oxides is an established methodology in a number of industrial processes (high density sludge systems for arsenic control in effluents from the mining industry, and in the treatment of textile dye effluent).

  20. Advances in tubular solid oxide fuel cell technology

    Energy Technology Data Exchange (ETDEWEB)

    Singhal, S.C. [Westinghouse Electric Corp., Pittsburgh, PA (United States)

    1996-12-31

    The design, materials and fabrication processes for the earlier technology Westinghouse tubular geometry cell have been described in detail previously. In that design, the active cell components were deposited in the form of thin layers on a ceramic porous support tube (PST). The tubular design of these cells and the materials used therein have been validated by successful electrical testing for over 65,000 h (>7 years). In these early technology PST cells, the support tube, although sufficiently porous, presented an inherent impedance to air flow toward air electrode. In order to reduce such impedance to air flow, the wall thickness of the PST was first decreased from the original 2 mm (the thick-wall PST) to 1.2 mm (the thin-wall PST). The calcia-stabilized zirconia support tube has now been completely eliminated and replaced by a doped lanthanum manganite tube in state-of-the-art SOFCs. This doped lanthanum manganite tube is extruded and sintered to about 30 to 35 percent porosity, and serves as the air electrode onto which the other cell components are fabricated in thin layer form. These latest technology cells are designated as air electrode supported (AES) cells.

  1. Association of indoor air pollution with rhinitis symptoms, atopy and nitric oxide levels in exhaled air

    DEFF Research Database (Denmark)

    Hersoug, Lars-Georg; Husemoen, Lise Lotte N; Thomsen, Simon Francis

    2010-01-01

    Exposure to particulate matter (PM) outdoors can induce airway inflammation and exacerbation of asthma in adults. However, there is limited knowledge about the effects of exposure to indoor PM. The aim of this study was to investigate the association of exposure to indoor sources of PM with rhini......Exposure to particulate matter (PM) outdoors can induce airway inflammation and exacerbation of asthma in adults. However, there is limited knowledge about the effects of exposure to indoor PM. The aim of this study was to investigate the association of exposure to indoor sources of PM...... with rhinitis symptoms, atopy and nitric oxide in exhaled air (FeNO) as a measure of airway inflammation....

  2. Solid Oxide Fuel Cells: Technology Status

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Prabhakar; Minh, Nguyen Q.

    2004-08-01

    In its most common configuration, solid oxide fuel cell (SOFC) uses an oxygen ion conducting ceramic electrolyte membrane, perovskite cathode and nickel cermet anode electrode. Cells operate in the 600-1000 C temperature range and utilize metallic or ceramic current collectors for cell-to-cell interconnection. Recent development in engineered electrode architectures, component materials chemistry, cell and stack designs and fabrication processes have led to significant improvement in the electrical performance and performance stability as well as reduction in the operating temperature of such cells. Large kW-size power generation systems have been designed and field demonstrated. This paper reviews the status of SOFC power generation systems with emphasis on cell and stack component materials, electrode reactions, materials reactions and corrosion processes

  3. High-Performance WSe2 Complementary Metal Oxide Semiconductor Technology and Integrated Circuits.

    Science.gov (United States)

    Yu, Lili; Zubair, Ahmad; Santos, Elton J G; Zhang, Xu; Lin, Yuxuan; Zhang, Yuhao; Palacios, Tomás

    2015-08-12

    Because of their extraordinary structural and electrical properties, two-dimensional materials are currently being pursued for applications such as thin-film transistors and integrated circuit. One of the main challenges that still needs to be overcome for these applications is the fabrication of air-stable transistors with industry-compatible complementary metal oxide semiconductor (CMOS) technology. In this work, we experimentally demonstrate a novel high performance air-stable WSe2 CMOS technology with almost ideal voltage transfer characteristic, full logic swing and high noise margin with different supply voltages. More importantly, the inverter shows large voltage gain (∼38) and small static power (picowatts), paving the way for low power electronic system in 2D materials.

  4. Catalytic wet air oxidation of chlorophenols over supported ruthenium catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Li Ning [Institut de recherches sur la catalyse et l' environnement de Lyon (IRCELYON), UMR 5256, CNRS/Universite Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France); Descorme, Claude [Institut de recherches sur la catalyse et l' environnement de Lyon (IRCELYON), UMR 5256, CNRS/Universite Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France)]. E-mail: claude.descorme@catalyse.cnrs.fr; Besson, Michele [Institut de recherches sur la catalyse et l' environnement de Lyon (IRCELYON), UMR 5256, CNRS/Universite Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France)

    2007-07-31

    A series of noble metal (Pt, Pd, Ru) loaded zirconia catalysts were evaluated in the catalytic wet air oxidation (CWAO) of mono-chlorophenols (2-CP, 3-CP, 4-CP) under relatively mild reaction conditions. Among the investigated noble metals, Ru appeared to be the best to promote the CWAO of CPs as far as incipient-wetness impregnation was used to prepare all the catalysts. The position of the chlorine substitution on the aromatic ring was also shown to have a significant effect on the CP reactivity in the CWAO over 3 wt.% Ru/ZrO{sub 2}. 2-CP was relatively easier to degradate compared to 3-CP and 4-CP. One reason could be the higher adsorption of 2-CP on the catalyst surface. Further investigations suggested that 3 wt.% Ru/ZrO{sub 2} is a very efficient catalyst in the CWAO of 2-CP as far as high 2-CP conversion and TOC abatement could still be reached at even lower temperature (393 K) and lower total pressure (3 MPa). Additionally, the conversion of 2-CP was demonstrated to increase with the initial pH of the 2-CP solution. The dechlorination reaction is promoted at higher pH. In all cases, the adsorption of the reactants and the reaction intermediates was shown to play a major role. All parameters that would control the molecule speciation in solution or the catalyst surface properties would have a key effect.

  5. Catalytic wet air oxidation of chlorophenols over supported ruthenium catalysts.

    Science.gov (United States)

    Li, Ning; Descorme, Claude; Besson, Michèle

    2007-07-31

    A series of noble metal (Pt, Pd, Ru) loaded zirconia catalysts were evaluated in the catalytic wet air oxidation (CWAO) of mono-chlorophenols (2-CP, 3-CP, 4-CP) under relatively mild reaction conditions. Among the investigated noble metals, Ru appeared to be the best to promote the CWAO of CPs as far as incipient-wetness impregnation was used to prepare all the catalysts. The position of the chlorine substitution on the aromatic ring was also shown to have a significant effect on the CP reactivity in the CWAO over 3wt.% Ru/ZrO(2). 2-CP was relatively easier to degradate compared to 3-CP and 4-CP. One reason could be the higher adsorption of 2-CP on the catalyst surface. Further investigations suggested that 3wt.% Ru/ZrO(2) is a very efficient catalyst in the CWAO of 2-CP as far as high 2-CP conversion and TOC abatement could still be reached at even lower temperature (393K) and lower total pressure (3MPa). Additionally, the conversion of 2-CP was demonstrated to increase with the initial pH of the 2-CP solution. The dechlorination reaction is promoted at higher pH. In all cases, the adsorption of the reactants and the reaction intermediates was shown to play a major role. All parameters that would control the molecule speciation in solution or the catalyst surface properties would have a key effect.

  6. Laboratory flammability studies of mixtures of hydrogen, nitrous oxide, and air

    Energy Technology Data Exchange (ETDEWEB)

    Cashdollar, K L; Hertzberg, M; Zlochower, I A; Lucci, C E; Green, G M; Thomas, R A [Bureau of Mines, Pittsburgh, PA (United States). Pittsburgh Research Center

    1992-06-26

    At the request of the Department of Energy and the Westinghouse Hanford Company, the Bureau of Mines has investigated the flammability of mixtures of hydrogen, nitrous oxide, and air. This work is relevant to the possible hazards of flammable gas generation from nuclear waste tanks at Hanford, WA. The tests were performed in a 120-L spherical chamber under both quiescent and turbulent conditions using both electric spark and pyrotechnic ignition sources. The data reported here for binary mixtures of hydrogen in air generally confirm the data of previous investigators, but they are more comprehensive than those reported previously. The results clarify to a greater extent the complications associated with buoyancy, turbulence, and selective diffusion. The data reported here for ternary mixtures of hydrogen and nitrous oxide in air indicate that small additions of nitrous oxide (relative to the amount of air) have little effect, but that higher concentrations of nitrous oxide (relative to air) significantly increase the explosion hazard.

  7. 40 CFR Appendix S to Part 50 - Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Nitrogen...

    Science.gov (United States)

    2010-07-01

    ... Ambient Air Quality Standards for Oxides of Nitrogen (Nitrogen Dioxide) S Appendix S to Part 50 Protection... National Ambient Air Quality Standards for Oxides of Nitrogen (Nitrogen Dioxide) 1. General (a) This... national ambient air quality standards for oxides of nitrogen as measured by nitrogen dioxide (“NO2...

  8. Oxidation mechanism of Fe–16Cr alloy as SOFC interconnect in dry/wet air

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zhi-Yuan [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Wang, Li-Jun, E-mail: lijunwang@ustb.edu.cn [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Li, Fu-Shen [School of Material Science Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Chou, Kuo-Chih [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China)

    2013-10-15

    Highlights: •A special thermodynamic description corresponding to the kinetics was applied. •We reported the relationships of degradation time with temperature and moisture. •”Turning time” in the Fe–16Cr alloy oxidation kinetic model was given. •The oxidation mechanism of Fe–16Cr alloy in the wet air was discussed. -- Abstract: Experimental study on the oxidation corrosions of Fe–16Cr alloy was carried out at 800–1100 °C under dry/wet air conditions. Faster oxidation rate was observed at higher temperature and water vapor content. The degradation time t{sub d} between two stages in oxidation process showed an exponential relationship with elevating corrosion temperature in dry air, and a linear relationship with the water content in the case of water vapor introduced to the system. The mechanism of oxidation corrosions of Fe–16Cr alloy was suggested by the Real Physical Picture (RPP) model. It was found that the break-away oxidation in stage II was controlled by diffusion at initial both in dry and wet air, then became linear with the exposure time, which implied that the oxidation rate was then controlled by chemical reaction of the interface between the metal and the oxidized scale. Moreover, the effect of water in the oxidation process is not only to supply more oxygen into system, but also to modify the structures of oxide scale due to the existence of hydrogen atom, which results in the accelerated corrosions.

  9. Can commonly-used fan-driven air cleaning technologies improve indoor air quality? A literature review

    DEFF Research Database (Denmark)

    Zhang, Yinping; Mo, Jinhan; Li, Yuguo

    2011-01-01

    Air cleaning techniques have been applied worldwide with the goal of improving indoor air quality. The effectiveness of applying these techniques varies widely, and pollutant removal efficiency is usually determined in controlled laboratory environments which may not be realized in practice. Some...... air cleaners are largely ineffective, and some produce harmful by-products. To summarize what is known regarding the effectiveness of fan-driven air cleaning technologies, a state-of-the-art review of the scientific literature was undertaken by a multidisciplinary panel of experts from Europe, North...... technologies was able to effectively remove all indoor pollutants and many were found to generate undesirable by-products during operation. (2) Particle filtration and sorption of gaseous pollutants were among the most effective air cleaning technologies, but there is insufficient information regarding long...

  10. Effect of photocatalytic oxidation technology on GaN CMP

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jie, E-mail: jie-wang11@mails.tsinghua.edu.cn; Wang, Tongqing, E-mail: wtq@mail.tsinghua.edu.cn; Pan, Guoshun, E-mail: pangs@mail.tsinghua.edu.cn; Lu, Xinchun, E-mail: xclu@mail.tsinghua.edu.cn

    2016-01-15

    Graphical abstract: - Highlights: • Photocatalytic oxidation technology was introduced to GaN CMP for the first time and proves to be more efficient than before. • XPS analysis reveals the planarization process by different N-type semiconductor particles. • Analyzing the effect of pH on photocatalytic oxidation in GaN CMP. • Proposing the photocatalytic oxidation model to reveal the removal mechanism. - Abstract: GaN is so hard and so chemically inert that it is difficult to obtain a high material removal rate (MRR) in the chemical mechanical polishing (CMP) process. This paper discusses the application of photocatalytic oxidation technology in GaN planarization. Three N-type semiconductor particles (TiO{sub 2}, SnO{sub 2}, and Fe{sub 2}O{sub 3}) are used as catalysts and added to the H{sub 2}O{sub 2}–SiO{sub 2}-based slurry. By optical excitation, highly reactive photoinduced holes are produced on the surface of the particles, which can oxidize OH{sup −} and H{sub 2}O absorbed on the surface of the catalysts; therefore, more OH* will be generated. As a result, GaN MRRs in an H{sub 2}O{sub 2}–SiO{sub 2}-based polishing system combined with catalysts are improved significantly, especially when using TiO{sub 2}, the MRR of which is 122 nm/h. The X-ray photoelectron spectroscopy (XPS) analysis shows the variation trend of chemical composition on the GaN surface after polishing, revealing the planarization process. Besides, the effect of pH on photocatalytic oxidation combined with TiO{sub 2} is analyzed deeply. Furthermore, the physical model of GaN CMP combined with photocatalytic oxidation technology is proposed to describe the removal mechanism of GaN.

  11. Inkjet Impregnation for Tailoring Air Electrode Microstructure to Improve Solid Oxide Cells Performance

    KAUST Repository

    Da’as, Eman H.

    2015-09-30

    The urge to lower the operating temperature of solid oxide cells (SOCs) to the intermediate ranges between 500-700°C motivated the research into impregnation processes, which offer highly efficient SOC air electrodes at low operating temperatures. Lack of controllability and reproducibility of this technique in the conventional way is still considered as an inadequacy for industrialization since it is performed manually. Therefore, inkjet-printing technology was proposed as an adequate approach to perform scalable and controllable impregnation for SOC air electrodes, which in turn leads to low operating temperatures. Composite LSM-ionic conductive air electrodes of weight ratio 1:2 were fabricated by inkjet impregnation of lanthanum strontium manganite (La0.8Sr0.2MnO3) precursor nitrates onto a porous ionic conductive backbone structure. First, porous yttria stabilized zirconia (8YSZ) substrates prepared by tape casting were used to study the influence of the printing parameters on the lateral dispersion and penetration of LSM ink inside the pores. XRD analysis confirmed the formation of LSM phase after calcination at 800°C for 2 h, while SEM revealed the formation of LSM nanostructures. It has been found by optical microscope observations that the spacing between the drops and the substrate temperature have a significant role in controlling the printing process. Next, the optimized printing parameters were applied in the inkjet impregnation of the LSM ink into porous YSZ electrodes that were spin coated on both sides of dense YSZ layers. LSM-YSZ composite air electrodes achieved an area specific resistance (ASR) of around 0.29 Ω.cm2 at 700°C. The performance of LSM-YSZ composite electrodes was influenced by the microstructure and the thickness, and by the electrode/electrolyte interface characteristics. As a result, the enhancement in LSM-YSZ composite electrode performance was observed due to the better percolation in LSM, YSZ and oxygen diffusion. Finally

  12. [Degradation of beta-naphthol by catalytic wet air oxidation].

    Science.gov (United States)

    Liu, Jie; Yu, Chao-Ying; Zhao, Pei-Qing; Chen, Ge-Xin

    2012-11-01

    A series of MnO(x)/nano-TiO2 catalysts were prepared and their application in degradation of beta-naphthol by catalytic wet air oxidation (CWAO) was investigated. The catalysts preparation conditions, reaction conditions and its stability were tested. The catalysts had been characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and temperature-programmed reduction (TPR) measurements. The results showed that the decrease of the COD removal for the degradation of beta-naphthol at high Mn loading was due to the aggregation of the highly dispersed Mn species and the formation of the correlated crystals. The decline of the COD removal at high calcination temperature was probably attributed to the weak electron transfer between Mn2O3 and MnO2 and the formation of the inactive Mn2O3. The COD removal had been falling slightly when the catalyst was used 6 times, and this was likely related to the decrease of the diffraction peaks. The catalyst had a high activity when the Mn loading (mass fraction) was 4% and the calcination temperature was 450 degrees C. The COD removal was up to 96.4% at 110 degrees C and 0.5 MPa with this catalyst. The COD removal of 92.4% could be obtained with the MnO(x)/nano-TiO2 catalyst was recycled 6 times. The Mn leaching at 50, 80, 110 and 150 degrees C were all less than 9.3 mg x L(-1) by means of Atomic Absorption Spectroscopy (AAS). The probable degradation pathway was proposed according to some publications.

  13. Experimental investigation of integrated air purifying technology for bioaerosol removal and inactivation in central air-conditioning system

    Institute of Scientific and Technical Information of China (English)

    ZHENG Xiaohong; LIU Hongmin; YE Xiaojiang; LI Kejun; WANG Ruzhu; ZHAO Liping; Lisa. X. Xu; CHEN Yazhu; JIN Xinqiao; GU Bo; BAI Jingfeng

    2004-01-01

    In this research, high voltage static electricity and ultraviolet technologies were integrated to an air purifying device which can be used to trap and kill airborne bacteria and viruses in central air-conditioning systems. An experimental platform was built to mimic the central air system, in which the efficacy of the newly built device was examined. In addition to the standard physical and chemical tests, bacteriophages were used to simulate airborne viruses in the experimental system. The bacteriophage suspension was aerosolized into the air with ultrasonic wave atomization. The result showed that more than 86% removal efficiency of micro-particles (<10 micron in diameter) were removed after the device was in operation in a building and more than 95% of bacteriophages in the experimental system. It is concluded that the integrated air purifier is suitable for controlling air quality and preventing virus transmission through the central air system.

  14. Nitric oxide in exhaled and aspirated nasal air as an objective measure of human response to indoor air pollution

    DEFF Research Database (Denmark)

    Kolarik, Barbara; Lagercrantz, L.; Sundell, Jan

    2009-01-01

    The concentration of nitric oxide (NO) in exhaled and aspirated nasal air was used to objectively assess human response to indoor air pollutants in a climate chamber exposure experiment. The concentration of NO was measured before exposure, after 2, and 4.5 h of exposure, using a chemiluminescence...... air was observed. After exposure to the reference condition the mean NO concentration was significantly reduced compared to pre-exposure. Together these changes resulted in significant differences in exhaled NO between exposure to reference and polluted conditions. NO in nasal air was not affected...... NO analyzer. Sixteen healthy female subjects were exposed to two indoor air pollutants and to a clean reference condition for 4.5 h. Subjective assessments of the environment were obtained by questionnaires. After exposure (4.5 h) to the two polluted conditions a small increase in NO concentration in exhaled...

  15. Hydrogen diffusivity in oxide layers formed in Zr alloy in air or steam

    Science.gov (United States)

    Kato, Taro; Takagi, Ikuji; Sakamoto, Kan; Aomi, Masaki

    2017-10-01

    The effect of the oxidation conditions on hydrogen diffusion in oxide layers in Zr alloy was experimentally studied. Samples of GNF-Ziron (high-iron Zircaloy-2-type alloy) sheets were oxidized in air or steam and then exposed to deuterium plasma to charge them with deuterium. Deuterium depth profiles in each sample were observed by nuclear reaction analysis during plasma exposure, and the deuterium diffusion coefficient D was estimated. The results showed that the D values of the steam-oxidized samples were high, whereas that of a steam-oxidized sample that was subsequently heated in vacuum was as low as those of air-oxidized samples. The difference in D was not attributed to the structure but is probably due to the presence of OH groups absorbed during steam oxidation.

  16. Oxidation Behaviour of Si3N4 Materials in Air and Nitrogen Atmosphere

    Institute of Scientific and Technical Information of China (English)

    ZHANGQitu; LINGZhida

    1999-01-01

    Si3N4 powder and hot-pressed Si3N4 ceramics added with Al2O3 are used for investigate their oxidation behvior in air and nitrogen atmosphere(with oxygen partial pressure PO2=1-10Pa),The oxidation products of Si3N4 are examined by chemical analysi,X-ray diffraction (XRD) and XPS method,Also, thermodynamic calculation is made to analyze oxidation behavior of Si3N4.The results show that only passive oxidation will occur when Si3N4 is oxidized in air at high temperature,whereas in N2 at high temperature,the active oxidation is dominant in spite of the existence of a little passive oxidation.

  17. TECHNOLOGY EVALUATION REPORT CEREX ENVIRONMENTAL SERVICES UV HOUND POINT SAMPLE AIR MONITOR

    Science.gov (United States)

    The USEPA's National Homeland Security Research Center (NHSRC) Technology Testing and Evaluation Program (TTEP) is carrying out performance tests on homeland security technologies. Under TTEP, Battelle evaluated the performance of the Cerex UV Hound point sample air monitor in de...

  18. Oxidative stress and inflammation generated DNA damage by exposure to air pollution particles

    DEFF Research Database (Denmark)

    Møller, Peter; Danielsen, Pernille Høgh; Karottki, Dorina Gabriela

    2014-01-01

    investigating air pollution particles. There is substantial evidence indicating that exposure to air pollution particles was associated with elevated levels of oxidatively damaged nucleobases in circulating blood cells and urine from humans, which is supported by observations of elevated levels of genotoxicity...... of PM sampled at different locations or times. Small air pollution particles did not appear more hazardous than larger particles, which is consistent with the notion that constituents such as metals and organic compounds also are important determinants for PM-generated oxidative stress and inflammation....... In addition, the results indicate that PM-mediated ROS production is involved in the generation of inflammation and activated inflammatory cells can increase their ROS production. The observations indicate that air pollution particles generate oxidatively damaged DNA by promoting a milieu of oxidative stress...

  19. Durable rechargeable zinc-air batteries with neutral electrolyte and manganese oxide catalyst

    Science.gov (United States)

    Sumboja, Afriyanti; Ge, Xiaoming; Zheng, Guangyuan; Goh, F. W. Thomas; Hor, T. S. Andy; Zong, Yun; Liu, Zhaolin

    2016-11-01

    Neutral chloride-based electrolyte and directly grown manganese oxide on carbon paper are used as the electrolyte and air cathode respectively for rechargeable Zn-air batteries. Oxygen reduction and oxygen evolution reactions on manganese oxide show dependence of activities on the pH of the electrolyte. Zn-air batteries with chloride-based electrolyte and manganese oxide catalyst exhibit satisfactory voltage profile (discharge and charge voltage of 1 and 2 V at 1 mA cm-2) and excellent cycling stability (≈90 days of continuous cycle test), which is attributed to the reduced carbon corrosion on the air cathode and decreased carbonation in neutral electrolyte. This work describes a robust electrolyte system that improves the cycle life of rechargeable Zn-air batteries.

  20. Technologies for the Reduction of Nitrogen Oxides Emissions

    Directory of Open Access Journals (Sweden)

    Paulica Arsenie

    2015-06-01

    Full Text Available When it comes to gas turbines, their main problem concerning pollutant emissions is represented by nitric oxides. Among other emissions, sulphur oxides being much reduced due to the use of liquid distilled and gas fuels with a low content of sulphur. Using water or steam injection became the favourite method during the '80s and especially the '90s since "dry" methods and catalytic reduction were both at the beginning of the development phase. Catalytic convertors have been used since the '80s and they are still used although the costs of renewing the catalyst are very high. In the last twenty years a gradual decrease has been registered on the limits of nitric oxides from 75 ppm to 25 ppm, and now the target is oriented towards the 9 ppm level. The evolution of burning technologies of combustion makes it possible to control the level of production of nitric oxides even from the source without being necessary to use "humid" methods. This, of course, opened the market for gas turbines because they can function even in areas with limited quality water reserves, such as maritime platforms and in the desert. In this paper, we are going to show that, although water injection is still used, "dry" control technologies of burning became favourite methods for the majority of users on the industrial power generators market. The great dependency between the creation of nitric oxides and the temperature reveals the effect of direct water or steam injection on reducing nitric oxides. Recent research showed that a reduction up to 85% of nitric oxides may be obtained by using the water or steam injection all together with the improvement of aerodynamic character of the burning room.

  1. Catalytic wet air oxidation of aniline with nanocasted Mn-Ce-oxide catalyst.

    Science.gov (United States)

    Levi, R; Milman, M; Landau, M V; Brenner, A; Herskowitz, M

    2008-07-15

    The catalytic wet air oxidation of aqueous solution containing 1000 ppm aniline was conducted in a trickle-bed reactor packed with a novel nanocasted Mn-Ce-oxide catalyst (surface area of 300 m2/g) prepared using SBA-15 silica as a hard template. A range of liquid hourly space velocities (5-20 h(-1)) and temperatures (110-140 degrees C) at 10 bar of oxygen were tested. The experiments were conducted to provide the intrinsic performance of the catalysts. Complete aniline conversion, 90% TOC conversion, and 80% nitrogen mineralization were achieved at 140 degrees C and 5 h(-1). Blank experiments yielded relatively low homogeneous aniline (<35%) and negligible TOC conversions. Fast deactivation of the catalysts was experienced due to leaching caused by complexation with aniline. Acidification of the solution with HCI (molar HCI to aniline ratio of 1.2) was necessary to avoid colloidization and leaching of the nanoparticulate catalyst components. The catalyst displayed stable performance for over 200 h on stream.

  2. Assessment of international air pollution prevention and control technology. Volume 2. Technical report. Report to Congress under CAA amendments of 1990, section 901(e) public law 104-549. Final report, December 1993-December 1995

    Energy Technology Data Exchange (ETDEWEB)

    Burklin, C.; Gundappa, M.; Jones, D.

    1996-08-01

    The report gives results of a study that identifies new and innovative air pollution prevention and/or control technologies, of selected industrialized countries, that are not currently used extensively in the U.S. The study addressed technologies that prevent or control the emissions of the pollutants from each of four sources of air pollution: (1) Urban emissions--ozone precursors to include nitrogen oxides (NOx), volatile organic componds (VOCs), particulate matter (PM), and air toxics; (2) Motor vehicle emissions--NOx, carbon monoxide (CO), and PM; (3) Toxic air emissions--any one of the 189 compounds on the list of hazardous air pollutants (HAPs) in the 1990 CAAA (Title III); and (4) Acid deposition--NOx, sulfur oxides (SOx), and, to a lesser extent, VOCs. The report describes the approach taken to identify potentially useful technologies, gives results of the technology search and evaluation, and describes the selected technologies.

  3. Assessment of international air pollution prevention and control technology. Volume 1. Executive summary. Report to Congress under CAA amendments of 1990, section 901(e) public law 101-549. Final report, December 1993-December 1995

    Energy Technology Data Exchange (ETDEWEB)

    Burklin, C.; Gundappa, M.; Jones, D.

    1996-08-01

    The report gives results of a study that identifies new and innovative air pollution prevention and/or control technologies, of selected industrialized countries, that are not currently used extensively in the U.S. The study addressed technologies that prevent or control the emissions of the pollutants from each of four sources of air pollution: (1) Urban emissions--ozone precursors to include nitrogen oxides (NOx), volatile organic componds (VOCs), particulate matter (PM), and air toxics; (2) Motor vehicle emissions--NOx, carbon monoxide (CO), and PM; (3) Toxic air emissions--any one of the 189 compounds on the list of hazardous air pollutants (HAPs) in the 1990 CAAA (Title III); and (4) Acid deposition--NOx, sulfur oxides (SOx), and, to a lesser extent, VOCs. The report describes the approach taken to identify potentially useful technologies, gives results of the technology search and evaluation, and describes the selected technologies.

  4. Dry air effects on the copper oxides sensitive layers formation for ethanol vapor detection

    Energy Technology Data Exchange (ETDEWEB)

    Labidi, A., E-mail: Ahmed_laabidi@yahoo.fr [URPSC (UR 99/13-18) Unite de Recherche de Physique des Semiconducteurs et Capteurs, IPEST, Universite de Carthage, BP 51, La Marsa 2070, Tunis (Tunisia); Bejaoui, A.; Ouali, H. [URPSC (UR 99/13-18) Unite de Recherche de Physique des Semiconducteurs et Capteurs, IPEST, Universite de Carthage, BP 51, La Marsa 2070, Tunis (Tunisia); Akkari, F. Chaffar [Laboratoire de Photovoltaique et Materiaux Semi-conducteurs, ENIT, Universite de Tunis el Manar, BP 37, Le belvedere 1002, Tunis (Tunisia); Hajjaji, A.; Gaidi, M. [Laboratoire de Photovoltaique, Centre de Recherches et de technologies de l' energie, Technopole de Borj-Cedria, BP 95, 2050 Hammam-Lif (Tunisia); Kanzari, M. [Laboratoire de Photovoltaique et Materiaux Semi-conducteurs, ENIT, Universite de Tunis el Manar, BP 37, Le belvedere 1002, Tunis (Tunisia); Bessais, B. [Laboratoire de Photovoltaique, Centre de Recherches et de technologies de l' energie, Technopole de Borj-Cedria, BP 95, 2050 Hammam-Lif (Tunisia); Maaref, M. [URPSC (UR 99/13-18) Unite de Recherche de Physique des Semiconducteurs et Capteurs, IPEST, Universite de Carthage, BP 51, La Marsa 2070, Tunis (Tunisia)

    2011-09-15

    The copper oxide films have been deposited by thermal evaporation and annealed under ambient air and dry air respectively, at different temperatures. The structural characteristics of the films were investigated by X-ray diffraction. They showed the presences of two hydroxy-carbonate minerals of copper for annealing temperatures below 250 deg. C. Above this temperature the conductivity measurements during the annealing process, show a transition phase from metallic copper to copper oxides. The copper oxides sensitivity toward ethanol were performed using conductivity measurements at the working temperature of 200 deg. C. A decrease of conductivity was observed under ethanol vapor, showing the p-type semi-conducting characters of obtained copper oxide films. It was found that the sensing properties of copper oxide toward ethanol depend mainly on the annealing conditions. The best responses were obtained with copper layers annealed under dry air.

  5. Design principles for oxygen-reduction activity on perovskite oxide catalysts for fuel cells and metal-air batteries.

    Science.gov (United States)

    Suntivich, Jin; Gasteiger, Hubert A; Yabuuchi, Naoaki; Nakanishi, Haruyuki; Goodenough, John B; Shao-Horn, Yang

    2011-06-12

    The prohibitive cost and scarcity of the noble-metal catalysts needed for catalysing the oxygen reduction reaction (ORR) in fuel cells and metal-air batteries limit the commercialization of these clean-energy technologies. Identifying a catalyst design principle that links material properties to the catalytic activity can accelerate the search for highly active and abundant transition-metal-oxide catalysts to replace platinum. Here, we demonstrate that the ORR activity for oxide catalysts primarily correlates to σ-orbital (e(g)) occupation and the extent of B-site transition-metal-oxygen covalency, which serves as a secondary activity descriptor. Our findings reflect the critical influences of the σ orbital and metal-oxygen covalency on the competition between O(2)(2-)/OH(-) displacement and OH(-) regeneration on surface transition-metal ions as the rate-limiting steps of the ORR, and thus highlight the importance of electronic structure in controlling oxide catalytic activity.

  6. A development of solid oxide fuel cell technology

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Hee Chun; Lee, Chang Woo [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Kim, Kwy Youl; Yoon, Moon Soo; Kim, Ho Ki; Kim, Young Sik; Mun, Sung In; Eom, Sung Wuk [Korea Electrotechnology Research Inst., Changwon (Korea, Republic of)

    1995-12-31

    Solid oxide fuel cell which was consisted of ceramics has high power density and is very simple in shape. The project named A development of SOFC(Solid Oxide Fuel Cell) technology is to develop the unit cell fabrication processing and to evaluate the unit cell of solid oxide full cell. In this project, a manufacturing process of cathode by citrate method and polymeric precursor methods were established. By using tape casting method, high density thin electrolyte was manufactured and has high performance. Unit cell composed with La{sub 17}Sr{sub 13}Mn{sub 3} as cathode, 8YSZ electrolyte and 50% NiYSZ anode had a performance of O.85 W/cm{sup 2} and recorded 510 hours operation time. On the basis of these results. 100 cm{sup 2} class unit cell will be fabricated and tests in next program (author). 59 refs., 120 figs.

  7. Air-oxidized linalool-a frequent cause of fragrance contact allergy

    DEFF Research Database (Denmark)

    Bråred Christensson, Johanna; Andersen, Klaus Ejner; Bruze, Magnus

    2012-01-01

    Background. Linalool is a common fragrance terpene that, in pure form, is not allergenic or is a very weak allergen. However, linalool autoxidizes on air exposure, and the oxidation products can cause contact allergy. In a Swedish study, oxidized linalool 6.0% in petrolatum (pet.) gave 5% positiv...

  8. An international multicentre study on the allergenic activity of air-oxidized R-limonene

    DEFF Research Database (Denmark)

    Bråred Christensson, Johanna; Andersen, Klaus; Bruze, Magnus

    2013-01-01

    Limonene is a common fragrance terpene that, in its pure form, is not allergenic or is a very weak allergen. However, limonene autoxidizes on air exposure, and the oxidation products can cause contact allergy. Oxidized R-limonene has previously been patch tested in multicentre studies, giving 2-3...

  9. PROSPECTS FOR THE DEVELOPMENT OF TECHNOLOGY AIR CONDITIONING

    Directory of Open Access Journals (Sweden)

    O. V. Chernyshova

    2008-03-01

    Full Text Available In the article the evaporation cooling and spray (aqueous and air-to-water types of the air-conditioning systems are considered, their merits and demerits are analyzed; the new scheme of a conditioner is offered.

  10. DICP's New Technology for Manufacture of Propylene Oxide through Direct Oxidation of Propylene by Hydrogen Peroxide Passed Appraisal

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ In August 2008 the new technology for manufacture of pro-pylene oxide through direct oxidation of propylene by hy-drogen peroxide developed by Dalian Institute of Chemical Physics (DICP), CAS has passed the experts' appraisal or-ganized by the Science and Technology Department of Liaoning Province. It is told that this new technology, being an environmentally friendly new process, will eventually put an end to the severe pollution characteristic of the tradi-tional propylene oxide production process.

  11. Products and mechanisms of the oxidation of organic compounds in atmospheric air plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Marotta, Ester; Schiorlin, Milko; Paradisi, Cristina [Department of Chemical Sciences, Universita di Padova, Via Marzolo 1, 35131 Padova (Italy); Rea, Massimo, E-mail: cristina.paradisi@unipd.i [Department of Electrical Engineering, Universita di Padova, 35131 Padova (Italy)

    2010-03-31

    Atmospheric plasma-based technologies are developing as a powerful means for air purification, specifically for the oxidation of organic pollutants. To achieve a better control on the emissions produced by such treatments mechanistic insight is needed in the complex reactions of volatile organic compounds (VOCs) within the plasma. An account is given here of our comparative studies of the behaviour of model VOCs in response to different corona regimes (+dc, -dc and +pulsed) implemented within the same flow reactor. Model VOCs considered include two alkanes (n-hexane and i-octane), one aromatic hydrocarbon (toluene) and two halogenated methanes, dibromomethane (CH{sub 2}Br{sub 2}) and dibromodifluoromethane (CF{sub 2}Br{sub 2}, halon 1202). Efficiency and product data are reported and discussed as well as various possible initiation reactions. A powerful diagnostic tool is ion analysis, performed by atmospheric pressure chemical ionization-mass spectrometry: it provides a map of major ions and ion-molecule reactions and a rationale for interpreting current/voltage characteristics of dc coronas. It is shown that, depending on the specific VOC and corona regime adopted, different initiation steps prevail in the VOC-oxidation process and that the presence of a VOC, albeit in small amounts (500 ppm), can greatly affect some important plasma properties (ion population, current/voltage profile, post-discharge products).

  12. The Allure of Technology: How France and California Promoted Electric Vehicles to Reduce Urban Air Pollution

    OpenAIRE

    Calef, David; Goble, Robert

    2005-01-01

    All advanced industrialized societies face the problem of air pollution produced by motor vehicles. In spite of striking improvements in internal combustion engine technology, air pollution in most urban areas is still measured at levels determined to be harmful to human health. Throughout the 1990s and beyond, California and France both chose to improve air quality by means of technological innovation, adopting legislation that promoted clean vehicles, prominently among them, electric vehicl...

  13. Air-Driven Potassium Iodide-Mediated Oxidative Photocyclization of Stilbene Derivatives.

    Science.gov (United States)

    Matsushima, Tomoya; Kobayashi, Sayaka; Watanabe, Soichiro

    2016-09-02

    A new method has been developed for the potassium iodide-mediated oxidative photocyclization of stilbene derivatives. Compared with conventional iodine-mediated oxidative photocyclization reactions, this new method requires shorter reaction times and affords cyclized products in yields of 45-97%. This reaction proceeds with a catalytic amount of potassium iodide and works in an air-driven manner without the addition of an external scavenger. The radical-mediated oxidative photocyclization of stilbene derivatives using TEMPO was also investigated.

  14. A Study of the Factors Associated with Successful Technology Transfer and their Applicability to Air Force Technology Transfers.

    Science.gov (United States)

    1995-09-01

    relay race, where one runner passes the baton to the next. Richard Dorf describes in "Models for Technology Transfer From Universities and Research...Meeting. 9. Dorf , Richard C. "Models for Technology Transfer From Universities and Research Laboratories," Technology Management Publication TM1.1988...both located at Wright- Patterson Air Force Base, Ohio. Namely, Tim Sharp, Chief, Technology Transfer Division and my faculty advisor, Major Richard

  15. Enhancing the crystalline degree of carbon nanotubes by acid treatment, air oxidization and heat treatment

    Institute of Scientific and Technical Information of China (English)

    Chensha Li; Baoyou Zhang; Xingjuan Chen; Xiaoqing Hu; Ji Liang

    2005-01-01

    Three approaches of treating carbon nanotubes (CNTs) including acid treatment, air oxidization and heat treatment at high temperature were studied to enhance the crystalline degree of carbon nanotubes. High temperature heat-treatment elevates the crystalline degree of carbon nanotubes. Acid treatment removes parts of amorphous carbonaceous matter through its oxidization effect.Air oxidization disperses carbon nanotubes and amorphous carbonaceous matter. The treatment of combining acid treatment with heat-treatment further elevates the crystalline degree of carbon nanotubes comparing with acid treatment or heat-treatment. The combination of the three treatments creates the thorough effects of enhancing the crystalline degree of carbon nanotubes.

  16. Catalytic air oxidation of biomass-derived carbohydrates to formic acid.

    Science.gov (United States)

    Li, Jiang; Ding, Dao-Jun; Deng, Li; Guo, Qing-Xiang; Fu, Yao

    2012-07-01

    An efficient catalytic system for biomass oxidation to form formic acid was developed. The conversion of glucose to formic acid can reach up to 52% yield within 3 h when catalyzed by 5 mol% of H(5)PV(2)Mo(10)O(40) at only 373 K using air as the oxidant. Furthermore, the heteropolyacid can be used as a bifunctional catalyst in the conversion of cellulose to formic acid (yield=35%) with air as the oxidant. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Development of a Catalytic Wet Air Oxidation Method to Produce Feedstock Gases from Waste Polymers

    Science.gov (United States)

    Kulis, Michael J.; Guerrero-Medina, Karen J.; Hepp, Aloysius F.

    2012-01-01

    Given the high cost of space launch, the repurposing of biological and plastic wastes to reduce the need for logistical support during long distance and long duration space missions has long been recognized as a high priority. Described in this paper are the preliminary efforts to develop a wet air oxidation system in order to produce fuels from waste polymers. Preliminary results of partial oxidation in near supercritical water conditions are presented. Inherent corrosion and salt precipitation are discussed as system design issues for a thorough assessment of a second generation wet air oxidation system. This work is currently being supported by the In-Situ Resource Utilization Project.

  18. High-temperature oxidation behavior of Al2O3/TiAl matrix composite in air

    Institute of Scientific and Technical Information of China (English)

    AI TaoTao; WANG Fen; FENG XiaoMing

    2009-01-01

    The oxidation behavior of Al2O3/TiAl in situ composites fabricated by hot-pressing technology was in-vestigated at 900℃ in static air. The results indicate that the mass gains of the composites samples decrease gradually with increasing Nb2O5 content and the inert Al2O3 dispersoids effectively increase the oxidation resistance of the composites. The higher the Al2O3 dispersoids content, the more pro-nounced the effect. The primary oxidation precesses obey approximately the linear laws, and the cyclic oxidation precesses follow the parabolic laws. The oxidized sample containing Ti2AIN and TiAI phases in the scales exhibits excellent oxidation resistance. The oxide scale formed after exposure at 900℃ for 120 h is multiple-layered, consisting mainly of an outer TiC2 layer, an intermediate Al2O3 layer, and an inner TiO2+Al2O3 mixed layer. From the outer layer to the inner layer, TiO2+Al2O3 mixed layer presents the transit of AI-rich oxide to Ti-rich oxide mixed layer. Near the substrate, cross-section micrograph shows a relatively loose layer, and micro- and macro-pores remain on this layer, which is a transition layer and transferres from Al2O3+TiO2 scale to substrate. The thickness of oxide layer is about 20 μm. It is also found that continuous protective alumina scales can not be observed on the surface of oxida-tion scales. Ti ions diffuse outwardly to form the outer TiC2 layer, while oxygen ions transport inwardly to form the inner TiO2+Al2O3 mixed layer. Under long-time intensive oxidation exposure, the internal Al2O3 scale has s good adhesiveness with the outer TiO2 scale. No obvious spallation of the oxide scales occurs. The increased oxidation resistance by the presence of in situ Al2O3 particulates is at-tributed to the enhanced alumina-forming tendency and thin and dense scale formation. Al2O3 particu-lates enhance the potential barrier of Ti ions from M/MO interface to O/MO interface, thereby the TiO2growth rate decreases, which is also beneficial to

  19. CONCENTRATED AMBIENT AIR POLLUTION CREATES OXIDATIVE STRESS IN CNS MICROGLIA.

    Science.gov (United States)

    Nanometer size particles carry free radical activity on their surface and can produce oxidative stress (OS)-mediated damage upon impact to target cells. The initiating event of phage cell activation (i.e., the oxidative burst) is unknown, although many proximal events have been i...

  20. 76 FR 48073 - Public Hearing for Secondary National Ambient Air Quality Standards for Oxides of Nitrogen and...

    Science.gov (United States)

    2011-08-08

    ... AGENCY 40 CFR Part 50 RIN 2060-AO72 Public Hearing for Secondary National Ambient Air Quality Standards... titled ``Secondary National Ambient Air Quality Standards for Oxides of Nitrogen and Sulfur'' which was... ``Secondary National Ambient Air Quality Standards for Oxides of Nitrogen and Sulfur'' proposed rule should...

  1. 40 CFR 50.11 - National primary and secondary ambient air quality standards for oxides of nitrogen (with...

    Science.gov (United States)

    2010-07-01

    ... air quality standards for oxides of nitrogen (with nitrogen dioxide as the indicator). 50.11 Section... PRIMARY AND SECONDARY AMBIENT AIR QUALITY STANDARDS § 50.11 National primary and secondary ambient air quality standards for oxides of nitrogen (with nitrogen dioxide as the indicator). (a) The level of...

  2. Controls of nitrite oxidation in ammonia-removing biological air filters

    DEFF Research Database (Denmark)

    Juhler, Susanne; Ottosen, Lars Ditlev Mørck; Nielsen, Lars Peter

    2008-01-01

    In biological air filters ammonia is removed due to the action of Ammonia Oxidizing Bacteria (AOB) resulting in nitrite accumulation exceeding 100 mM. Among filters treating exhaust air from pig facilities successful establishment of Nitrite Oxidizing Bacteria (NOB) sometimes occurs, resulting...... in accumulation of nitrate rather than nitrite and a significant decline in pH. As a consequence, ammonia is removed more efficiently, but heterotrophic oxidation of odorous compounds might be inhibited.  To identify the controlling mechanisms of nitrite oxidation, full-scale biological air filters were...... investigated applying a broad in situ approach. Bacterial distribution and chemical gradients were examined at both a macro scale from filter inlet towards outlet and on a micro scale within the intact biofilm, applying Fluorescence in situ Hybridization (FISH), electrochemical microsensors, and chemical...

  3. Performance of ultraviolet photocatalytic oxidation for indoor air applications: systematic experimental evaluation.

    Science.gov (United States)

    Zhong, Lexuan; Haghighat, Fariborz; Lee, Chang-Seo; Lakdawala, Ness

    2013-10-15

    Photocatalytic oxidation (PCO) is a promising technology that has potential to be applied in mechanically ventilated buildings to improve indoor air quality (IAQ). However, the major research studies were done in bench-top scale reactors under ideal reaction conditions. In addition, no study has been carried out on the investigation of the ozonation and photolysis effect using a pilot duct system. The objective of this study is the development of methodologies to evaluate the performance of PCO systems. A systematic parametric evaluation of the effects of various kinetic parameters, such as compound's type, inlet concentration, airflow rate, light intensity, and relative humidity, was conducted, and new interpretations were provided from a fundamental analysis. In addition, the photolysis effect under vacuum ultraviolet (VUV) irradiation for a variety of volatile organic compounds (VOCs) was examined for the first time in a pilot duct system. The performance comparison of ultraviolet C (UVC)-PCO and VUV-PCO was also discussed due to the presence of ozone. Moreover, the formation of by-products generated with or without ozone generation was fully compared to evaluate the PCO technology.

  4. Technologies of deep-oxidation under high temperature in wastewater treatment%废水高温深度氧化处理技术

    Institute of Scientific and Technical Information of China (English)

    赵国方; 赵红斌

    2001-01-01

    介绍了多种废水高温深度氧化技术,包括湿式空气氧化技术、催化湿式氧化技术、湿式过氧化物氧化技术、超临界水氧化技术和焚烧技术,其中着重比较了焚烧技术中四种炉型的特点。%Some technologies about deep-oxidation under high temperature in wastewater treatment were introduced, including wet air oxidation(WAO),catalyst wet air oxidation(CWAO),wet peroxide oxidation(WPO),supercritical water oxidation(SCWO),and incinerating technology.Four types of incinerators were compared by their features emphatically.

  5. Operation technology of air treatment system in nuclear facilities

    CERN Document Server

    Chun, Y B; Hwong, Y H; Lee, H K; Min, D K; Park, K J; Uom, S H; Yang, S Y

    2001-01-01

    Effective operation techniques were reviewed on the air treatment system to protect the personnel in nuclear facilities from the contamination of radio-active particles and to keep the environment clear. Nuclear air treatment system consisted of the ventilation and filtering system was characterized by some test. Measurement of air velocity of blowing/exhaust fan in the ventilation system, leak tests of HEPA filters in the filtering, and measurement of pressure difference between the areas defined by radiation level were conducted. The results acquired form the measurements were reflected directly for the operation of air treatment. In the abnormal state of virus parts of devices composted of the system, the repairing method, maintenance and performance test were also employed in operating effectively the air treatment system. These measuring results and techniques can be available to the operation of air treatment system of PIEF as well as the other nuclear facilities in KAERI.

  6. Air Oxidation of Activated Carbon to Synthesize a Biomimetic Catalyst for Hydrolysis of Cellulose.

    Science.gov (United States)

    Shrotri, Abhijit; Kobayashi, Hirokazu; Fukuoka, Atsushi

    2016-06-01

    Oxygenated carbon catalyzes the hydrolysis of cellulose present in lignocellulosic biomass by utilizing the weakly acidic functional groups on its surface. Here we report the synthesis of a biomimetic carbon catalyst by simple and economical air-oxidation of a commercially available activated carbon. Air- oxidation at 450-500 °C introduced 2000-2400 μmol g(-1) of oxygenated functional groups on the material with minor changes in the textural properties. Selectivity towards the formation of carboxylic groups on the catalyst surface increased with the increase in oxidation temperature. The degree of oxidation on carbon catalyst was found to be proportional to its activity for hydrolysis of cellulose. The hydrolysis of eucalyptus in the presence of carbon oxidized at 475 °C afforded glucose yield of 77 % and xylose yield of 67 %.

  7. Nitric oxide density measurements in air and air/fuel nanosecond pulse discharges by laser induced fluorescence

    Science.gov (United States)

    Uddi, M.; Jiang, N.; Adamovich, I. V.; Lempert, W. R.

    2009-04-01

    Laser induced fluorescence is used to measure absolute nitric oxide concentrations in air, methane-air and ethylene-air non-equilibrium plasmas, as a function of time after initiation of a single pulse, 20 kV peak voltage, 25 ns pulse duration discharge. A mixture of NO and nitrogen with known composition (4.18 ppm NO) is used for calibration. Peak NO density in air at 60 Torr, after a single pulse, is ~8 × 1012 cm-3 (~4.14 ppm) occurring at ~250 µs after the pulse, with decay time of ~16.5 ms. Peak NO atom mole fraction in a methane-air mixture with equivalence ratio of phiv = 0.5 is found to be approximately equal to that in air, with approximately the same rise and decay rate. In an ethylene-air mixture (also with equivalence ratio of phiv = 0.5), the rise and decay times are comparable to air and methane-air, but the peak NO concentration is reduced by a factor of approximately 2.5. Spontaneous emission measurements show that excited electronic states N2(C 3Π) and NO(A 2Σ) in air at P = 60 Torr decay within ~20 ns and ~1 µs, respectively. Kinetic modelling calculations incorporating air plasma kinetics complemented with the GRI Mech 3.0 hydrocarbon oxidation mechanism are compared with the experimental data using three different NO production mechanisms. It is found that NO concentration rise after the discharge pulse is much faster than predicted by Zel'dovich mechanism reactions, by two orders of magnitude, but much slower compared with reactions of electronically excited nitrogen atoms and molecules, also by two orders of magnitude. It is concluded that processes involving long lifetime (~100 µs) metastable states, such as N2(X 1Σ,v) and O2(b 1Σ), formed by quenching of the metastable N2(A 3Σ) state by ground electronic state O2, may play a dominant role in NO formation. NO decay, in all cases, is found to be dominated by the reverse Zel'dovich reaction, NO + O → N + O2, as well as by conversion into NO2 in a reaction of NO with ozone.

  8. Can commonly-used fan-driven air cleaning technologies improve indoor air quality? A literature review

    Science.gov (United States)

    Zhang, Yinping; Mo, Jinhan; Li, Yuguo; Sundell, Jan; Wargocki, Pawel; Zhang, Jensen; Little, John C.; Corsi, Richard; Deng, Qihong; Leung, Michael H. K.; Fang, Lei; Chen, Wenhao; Li, Jinguang; Sun, Yuexia

    2011-08-01

    Air cleaning techniques have been applied worldwide with the goal of improving indoor air quality. The effectiveness of applying these techniques varies widely, and pollutant removal efficiency is usually determined in controlled laboratory environments which may not be realized in practice. Some air cleaners are largely ineffective, and some produce harmful by-products. To summarize what is known regarding the effectiveness of fan-driven air cleaning technologies, a state-of-the-art review of the scientific literature was undertaken by a multidisciplinary panel of experts from Europe, North America, and Asia with expertise in air cleaning, aerosol science, medicine, chemistry and ventilation. The effects on health were not examined. Over 26,000 articles were identified in major literature databases; 400 were selected as being relevant based on their titles and abstracts by the first two authors, who further reduced the number of articles to 160 based on the full texts. These articles were reviewed by the panel using predefined inclusion criteria during their first meeting. Additions were also made by the panel. Of these, 133 articles were finally selected for detailed review. Each article was assessed independently by two members of the panel and then judged by the entire panel during a consensus meeting. During this process 59 articles were deemed conclusive and their results were used for final reporting at their second meeting. The conclusions are that: (1) None of the reviewed technologies was able to effectively remove all indoor pollutants and many were found to generate undesirable by-products during operation. (2) Particle filtration and sorption of gaseous pollutants were among the most effective air cleaning technologies, but there is insufficient information regarding long-term performance and proper maintenance. (3) The existing data make it difficult to extract information such as Clean Air Delivery Rate (CADR), which represents a common benchmark for

  9. Environmental Technology Verification: Supplement to Test/QA Plan for Biological and Aerosol Testing of General Ventilation Air Cleaners; Bioaerosol Inactivation Efficiency by HVAC In-Duct Ultraviolet Light Air Cleaners

    Science.gov (United States)

    The Air Pollution Control Technology Verification Center has selected general ventilation air cleaners as a technology area. The Generic Verification Protocol for Biological and Aerosol Testing of General Ventilation Air Cleaners is on the Environmental Technology Verification we...

  10. Investigating the air oxidation of V(II) ions in a vanadium redox flow battery

    Science.gov (United States)

    Ngamsai, Kittima; Arpornwichanop, Amornchai

    2015-11-01

    The air oxidation of vanadium (V(II)) ions in a negative electrolyte reservoir is a major side reaction in a vanadium redox flow battery (VRB), which leads to electrolyte imbalance and self-discharge of the system during long-term operation. In this study, an 80% charged negative electrolyte solution is employed to investigate the mechanism and influential factors of the reaction in a negative-electrolyte reservoir. The results show that the air oxidation of V(II) ions occurs at the air-electrolyte solution interface area and leads to a concentration gradient of vanadium ions in the electrolyte solution and to the diffusion of V(II) and V(III) ions. The effect of the ratio of the electrolyte volume to the air-electrolyte solution interface area and the concentrations of vanadium and sulfuric acid in an electrolyte solution is investigated. A higher ratio of electrolyte volume to the air-electrolyte solution interface area results in a slower oxidation reaction rate. The high concentrations of vanadium and sulfuric acid solution also retard the air oxidation of V(II) ions. This information can be utilized to design an appropriate electrolyte reservoir for the VRB system and to prepare suitable ingredients for the electrolyte solution.

  11. Selectively oxidized vertical-cavity laser performance and technology

    Energy Technology Data Exchange (ETDEWEB)

    Choquette, K.D.; Hou, H.Q.; Geib, K.M.; Hammons, B.E.

    1998-02-01

    The authors discuss revolutionary performance advances in selectively oxidized vertical-cavity surface emitting lasers (VCSELs), which have enabled low operating power laser diodes appropriate for aerospace applications. Incorporating buried oxide layers converted from AIGaAs layers within the laser cavity produces enhanced optical and electrical confinement enabling superior laser performance, such as high efficiency and modulation bandwidth. VCSELs also shown to be viable over varied environmental conditions such as ambient temperature and ionized radiation. The development of novel VCSEL technologies for advanced system applications is also described. Two dimensional individually addressable VCSEL arrays exhibit uniform threshold and operating characteristics. Bottom emitting 850 nm VCSEL arrays fabricated using wafer fusion are also reported.

  12. Time resolved study of hydroxyl radical oxidation of oleic acid at the air-water interface

    Science.gov (United States)

    Zhang, Xinxing; Barraza, Kevin M.; Upton, Kathleen T.; Beauchamp, J. L.

    2017-09-01

    The ubiquity of oleic acid (OA) renders it a poster child for laboratory investigations of environmental oxidation chemistry. In the current study, mechanistic details of the oxidation of OA by hydroxyl radicals at the air-water interface are investigated using field-induced droplet ionization mass spectrometry (FIDI-MS). Products from OH oxidation of both unsaturated and saturated carbon atoms are identified, and mechanisms for both types of oxidation processes are proposed. Uptake of oxygen in the interfacial layer increases linearly with time, consistent with Langmuir-Hinshelwood reaction kinetics. These results provide fundamental knowledge relating to OH initiated degradation of fatty acids in atmospheric aerosols.

  13. Dynamic Resectorization and Coordination Technology: An Evaluation of Air Traffic Control Complexity

    Science.gov (United States)

    Brinton, Christopher R.

    1996-01-01

    The work described in this report is done under contract with the National Aeronautics and Space Administration (NASA) to support the Advanced Air Transportation Technology (AATR) program. The goal of this program is to contribute to and accelerate progress in Advanced Air Transportation Technologies. Wyndemere Incorporated is supporting this goal by studying the complexity of the Air Traffic Specialist's role in maintaining the safety of the Air Transportation system. It is envisioned that the implementation of Free Flight may significantly increase the complexity and difficulty of maintaining this safety. Wyndemere Incorporated is researching potential methods to reduce this complexity. This is the final report for the contract.

  14. Photolytic and photocatalytic oxidation of perchloroethylene in air

    Science.gov (United States)

    Liu, Yun-Chieh

    2000-11-01

    The perchloroethylene (PCE) photolytic and photocatalytic oxidation reactions took place simultaneously when the UVC light and TiO2 catalyst were used. Each of these two processes was studied separately in this work. The photolytic oxidation of PCE was performed using UVC light without TiO2 under different reaction conditions including temperature, humidity, reactor diameter, PCE inlet concentration, and space time. It was found that the PCE photolytic oxidation process followed the second-order reaction model. Both the chlorine free radical induced chain reaction and the non-chain reaction were proposed to explain the PCE degradation and by- products. The reactor wall played an important role in quenching the photolytic oxidation reaction. The PCE conversion increased to a maximum when the diameter of the reactor decreased to 35-mm, and then decreased after that. This phenomenon could be due to a wall quenching effect. The PCE conversion decreased when temperature increased. This was caused by a decrease of UVC light intensity and significant wall effect at high temperature. The PCE conversion was found to be independent from humidity condition. This indicated that the water molecule was not involved in the PCE photolytic oxidation reaction. The PCE photocatalytic oxidation reaction was performed using UVA light with TiO2 catalyst under various factors: humidity, temperature, space time, PCE inlet concentration, and light intensity. This was done to examine their effect on PCE conversion. The PCE conversion decreased as the humidity or temperature increased. The temperature effect could be caused by the decrease of UVA light intensity and desorption of PCE molecules from the catalyst surface at high temperature. The PCE inlet concentration effect showed the PCE photocatalytic oxidation followed the Langmuir- Hinshelwood model. The light intensity had a positive effect on PCE conversion. The effect of TiO2 catalyst distribution on PCE conversion was also studied. A

  15. The Clean Air Act Amendments of 1990: Hazardous Air Pollutant Requirements and the DOE Clean Coal Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Moskowitz, P.D.; DePhillips, M.; Fthenakis, V.M. [Brookhaven National Lab., Upton, NY (United States); Hemenway, A. [USDOE Assistant Secretary for Fossil Energy, Washington, DC (United States)

    1991-12-31

    The purpose of the US Department of Energy -- Office of Fossil Energy (DOE FE) Clean Coal Technology Program (CCTP) is to provide the US energy marketplace with advanced, efficient, and environmentally sound coal-based technologies. The design, construction, and operation of Clean Coal Technology Demonstration Projects (CCTDP) will generate data needed to make informed, confident decisions on the commercial readiness of these technologies. These data also will provide information needed to ensure a proactive response by DOE and its industrial partners to the establishment of new regulations or a reactive response to existing regulations promulgated by the US Environmental Protection Agency (EPA). The objectives of this paper are to: (1) Present a preliminary examination of the potential implications of the Clean Air Act Amendments (CAAA) -- Title 3 Hazardous Air Pollutant requirements to the commercialization of CCTDP; and (2) help define options available to DOE and its industrial partners to respond to this newly enacted Legislation.

  16. The Clean Air Act Amendments of 1990: Hazardous Air Pollutant Requirements and the DOE Clean Coal Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Moskowitz, P.D.; DePhillips, M.; Fthenakis, V.M. (Brookhaven National Lab., Upton, NY (United States)); Hemenway, A. (USDOE Assistant Secretary for Fossil Energy, Washington, DC (United States))

    1991-01-01

    The purpose of the US Department of Energy -- Office of Fossil Energy (DOE FE) Clean Coal Technology Program (CCTP) is to provide the US energy marketplace with advanced, efficient, and environmentally sound coal-based technologies. The design, construction, and operation of Clean Coal Technology Demonstration Projects (CCTDP) will generate data needed to make informed, confident decisions on the commercial readiness of these technologies. These data also will provide information needed to ensure a proactive response by DOE and its industrial partners to the establishment of new regulations or a reactive response to existing regulations promulgated by the US Environmental Protection Agency (EPA). The objectives of this paper are to: (1) Present a preliminary examination of the potential implications of the Clean Air Act Amendments (CAAA) -- Title 3 Hazardous Air Pollutant requirements to the commercialization of CCTDP; and (2) help define options available to DOE and its industrial partners to respond to this newly enacted Legislation.

  17. Recent key technical barriers in solid oxide fuel cell technology

    Directory of Open Access Journals (Sweden)

    Milewski Jarosław

    2014-03-01

    Full Text Available High-temperature solid oxide fuel cells (SOFCs are considered as suitable components of future large-scale clean and efficient power generation systems. However, at its current stage of development some technical barriers exists which limit SOFC’s potential for rapid large-scale deployment. The present article aims at providing solutions to key technical barriers in SOFC technology. The focus is on the solutions addressing thermal resistance, fuel reforming, energy conversion efficiency, materials, design, and fuel utilisation issues.

  18. AlliedSignal solid oxide fuel cell technology

    Energy Technology Data Exchange (ETDEWEB)

    Minh, N.; Barr, K.; Kelly, P.; Montgomery, K. [AlliedSignal Aerospace Equipment Systems, Torrance, CA (United States)

    1996-12-31

    AlliedSignal has been developing high-performance, lightweight solid oxide fuel cell (SOFC) technology for a broad spectrum of electric power generation applications. This technology is well suited for use in a variety of power systems, ranging from commercial cogeneration to military mobile power sources. The AlliedSignal SOFC is based on stacking high-performance thin-electrolyte cells with lightweight metallic interconnect assemblies to form a compact structure. The fuel cell can be operated at reduced temperatures (600{degrees} to 800{degrees}C). SOFC stacks based on this design has the potential of producing 1 kW/kg and 1 ML. This paper summarizes the technical status of the design, manufacture, and operation of AlliedSignal SOFCs.

  19. Photo-oxidation of Acetone to Formic Acid in Synthetic Air and Its Atmospheric Implication.

    Science.gov (United States)

    Chattopadhyay, Aparajeo; Chatterjee, Piyali; Chakraborty, Tapas

    2015-07-23

    Acetone photo-oxidation in synthetic air under exposure of 311 nm ultraviolet light has been studied, and the photo-oxidation products are identified by means of infrared spectroscopy. Analysis reveals that formic acid is one of the major products, although there have been debates in the past concerning the authenticity of formation of this acid in synthetic air via the photo-oxidation pathway. The quantum yield of formation of this acid is similar to that of other major photoproducts like methanol, formaldehyde, and carbon monoxide. The reaction yield, however, decreases with an increase in total air pressure in the reaction cell, but it is still significant at pressures relevant to tropospheric conditions. A kinetic model has been used to simulate the measured reaction kinetics, and the quantum yields predicted by the model are found to be consistent with the measured yields for different durations of light exposure. The same model has also been used to investigate the effect of atmospheric nitric oxide on the fate of formation of this acid in the troposphere. Although nitric oxide is known to be a quencher of peroxy radicals, the precursors of formaldehyde and formic acid in acetone photo-oxidation, but our model predicts that this oxide plays a positive role in the overall reaction kinetics for production of this acid in the troposphere.

  20. Air-Impregnated Nanoporous Anodic Aluminum Oxide Layers for Enhancing the Corrosion Resistance of Aluminum.

    Science.gov (United States)

    Jeong, Chanyoung; Lee, Junghoon; Sheppard, Keith; Choi, Chang-Hwan

    2015-10-13

    Nanoporous anodic aluminum oxide layers were fabricated on aluminum substrates with systematically varied pore diameters (20-80 nm) and oxide thicknesses (150-500 nm) by controlling the anodizing voltage and time and subsequent pore-widening process conditions. The porous nanostructures were then coated with a thin (only a couple of nanometers thick) Teflon film to make the surface hydrophobic and trap air in the pores. The corrosion resistance of the aluminum substrate was evaluated by a potentiodynamic polarization measurement in 3.5 wt % NaCl solution (saltwater). Results showed that the hydrophobic nanoporous anodic aluminum oxide layer significantly enhanced the corrosion resistance of the aluminum substrate compared to a hydrophilic oxide layer of the same nanostructures, to bare (nonanodized) aluminum with only a natural oxide layer on top, and to the latter coated with a thin Teflon film. The hydrophobic nanoporous anodic aluminum oxide layer with the largest pore diameter and the thickest oxide layer (i.e., the maximized air fraction) resulted in the best corrosion resistance with a corrosion inhibition efficiency of up to 99% for up to 7 days. The results demonstrate that the air impregnating the hydrophobic nanopores can effectively inhibit the penetration of corrosive media into the pores, leading to a significant improvement in corrosion resistance.

  1. Novel photocatalysis oxidation system UV/Fe2+/air to degrade 4-CP wastewater

    Institute of Scientific and Technical Information of China (English)

    DU Yingxun; ZHOU Minghua; LEI Lecheng

    2005-01-01

    This paper reported the degradation of 4-CP wastewater by a novel photocatalysis oxidation system--UV/Fe2+/air system, in which air was used as a cheap oxidant that reacted with the excitation state of organics to form H2O2 under the UV light. The formed H2O2 reacted with the added ferrous ion to form Fenton reaction and led to the quick degradation of organic pollutants. It was found that 4-CP could be completely removed within 40 min. The degradation of 4-CP in the UV/Fe2+/air system was superior to the conventional UV/Fenton system (the initial concentration of H2O2 was 22 mg-L-1). UV/Fe2+/air is an effective and cheap method for treatment of the organics that can be excited by UV light.

  2. Cryogenic hydrogen-induced air-liquefaction technologies for combined-cycle propulsion applications

    Science.gov (United States)

    Escher, William J. D.

    1992-01-01

    Given here is a technical assessment of the realization of cryogenic hydrogen induced air liquefaction technologies in a prospective onboard aerospace vehicle process setting. The technical findings related to the status of air liquefaction technologies are reviewed. Compact lightweight cryogenic heat exchangers, heat exchanger atmospheric constituent fouling alleviation measures, para/ortho-hydrogen shift-conversion catalysts, cryogenic air compressors and liquid air pumps, hydrogen recycling using slush hydrogen as a heat sink, liquid hydrogen/liquid air rocket-type combustion devices, and technically related engine concepts are discussed. Much of the LACE work is related to aerospaceplane propulsion concepts that were developed in the 1960's. Emphasis is placed on the Liquid Air Cycle Engine (LACE).

  3. Fast oxidation processes from emission to ambient air introduction of aerosol emitted by residential log wood stoves

    Science.gov (United States)

    Nalin, Federica; Golly, Benjamin; Besombes, Jean-Luc; Pelletier, Charles; Aujay-Plouzeau, Robin; Verlhac, Stéphane; Dermigny, Adrien; Fievet, Amandine; Karoski, Nicolas; Dubois, Pascal; Collet, Serge; Favez, Olivier; Albinet, Alexandre

    2016-10-01

    Little is known about the impact of post-combustion processes, condensation and dilution, on the aerosol concentration and chemical composition from residential wood combustion. The evolution of aerosol emitted by two different residential log wood stoves (old and modern technologies) from emission until it is introduced into ambient air was studied under controlled "real" conditions. The first objective of this research was to evaluate the emission factors (EF) of polycyclic aromatic hydrocarbons (PAH) and their nitrated and oxygenated derivatives from wood combustion. These toxic substances are poorly documented in the literature. A second objective was to evaluate the oxidation state of the wood combustion effluent by studying these primary/secondary compounds. EFs of Σ37PAHs and Σ27Oxy-PAHs were in the same range and similar to those reported in literature (4-240 mg kg-1). Σ31Nitro-PAH EFs were 2-4 orders of magnitude lower (3.10-2-8.10-2 mg kg-1) due to the low temperature and low emission of NO2 from wood combustion processes. An increase of equivalent EF of PAH derivatives was observed suggesting that the oxidation state of the wood combustion effluent from the emission point until its introduction in ambient air changed in a few seconds. These results were confirmed by the study of both, typical compounds of SOA formation from PAH oxidation and, PAH ratio-ratio plots commonly used for source evaluation.

  4. Acquisition: Air Force Transition of Advanced Technology Programs to Military Applications

    Science.gov (United States)

    2006-05-31

    Requirements Review and Assessment process examines capabilities in Global Strike, Homeland Security, Global Response, Global Mobility , Air and Space...Sum m ary of A dvanced T echnology D evelopm ent Projects R eview ed 23 Note: See footnotes at the end of the appendix. Advanced Technology...Armaments Center (AAC) Yes Yes No Yes Yes n/a10 (Cat 2B) Yes Yes Global Air Mobility Advanced Technologies

  5. The impact of changing technology on the demand for air transportation

    Science.gov (United States)

    Kneafsey, J. T.; Taneja, N. K.

    1978-01-01

    Demand models for air transportation that are sensitive to the impact of changing technology were developed. The models are responsive to potential changes in technology, and to changing economic, social, and political factors as well. In addition to anticipating the wide differences in the factors influencing the demand for long haul and short haul air travel, the models were designed to clearly distinguish among the unique features of these markets.

  6. Experimental Validation of Stratified Flow Phenomena, Graphite Oxidation, and Mitigation Strategies of Air Ingress Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Chang Ho Oh; Eung Soo Kim; Hee Cheon No; Nam Zin Cho

    2008-12-01

    The US Department of Energy is performing research and development (R&D) that focuses on key phenomena that are important during challenging scenarios that may occur in the Next Generation Nuclear Plant (NGNP) Program / GEN-IV Very High Temperature Reactor (VHTR). Phenomena identification and ranking studies (PIRT) to date have identified the air ingress event, following on the heels of a VHTR depressurization, as very important (Schultz et al., 2006). Consequently, the development of advanced air ingress-related models and verification and validation (V&V) are very high priority for the NGNP program. Following a loss of coolant and system depressurization, air will enter the core through the break. Air ingress leads to oxidation of the in-core graphite structure and fuel. The oxidation will accelerate heat-up of the bottom reflector and the reactor core and will cause the release of fission products eventually. The potential collapse of the bottom reflector because of burn-off and the release of CO lead to serious safety problems. For estimation of the proper safety margin we need experimental data and tools, including accurate multi-dimensional thermal-hydraulic and reactor physics models, a burn-off model, and a fracture model. We also need to develop effective strategies to mitigate the effects of oxidation. The results from this research will provide crucial inputs to the INL NGNP/VHTR Methods R&D project. This project is focused on (a) analytical and experimental study of air ingress caused by density-driven, stratified, countercurrent flow, (b) advanced graphite oxidation experiments, (c) experimental study of burn-off in the bottom reflector, (d) structural tests of the burnt-off bottom reflector, (e) implementation of advanced models developed during the previous tasks into the GAMMA code, (f) full air ingress and oxidation mitigation analyses, (g) development of core neutronic models, (h) coupling of the core neutronic and thermal hydraulic models, and (i

  7. Unusually high soil nitrogen oxide emissions influence air quality in a high-temperature agricultural region.

    Science.gov (United States)

    Oikawa, P Y; Ge, C; Wang, J; Eberwein, J R; Liang, L L; Allsman, L A; Grantz, D A; Jenerette, G D

    2015-11-10

    Fertilized soils have large potential for production of soil nitrogen oxide (NOx=NO+NO2), however these emissions are difficult to predict in high-temperature environments. Understanding these emissions may improve air quality modelling as NOx contributes to formation of tropospheric ozone (O3), a powerful air pollutant. Here we identify the environmental and management factors that regulate soil NOx emissions in a high-temperature agricultural region of California. We also investigate whether soil NOx emissions are capable of influencing regional air quality. We report some of the highest soil NOx emissions ever observed. Emissions vary nonlinearly with fertilization, temperature and soil moisture. We find that a regional air chemistry model often underestimates soil NOx emissions and NOx at the surface and in the troposphere. Adjusting the model to match NOx observations leads to elevated tropospheric O3. Our results suggest management can greatly reduce soil NOx emissions, thereby improving air quality.

  8. Advanced manufacturing technologies for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Uhlenbruck, S.; Nedelec, R.; Buchkremer, H.P.; Bram, M.; Menzler, N.H.; Stover, D. [Forschungszentrum Julich GmbH, Julich (Germany). Inst. of Energy Research

    2009-07-01

    Advances in manufacturing technologies play an important role for the marketability of solid oxide fuel cells (SOFC). Highly cost-effective mass production methods are necessary in order to meet the industry's demands for both stationary and mobile application. Sol-gel methods have already been used for several years as a method of producing thin mesoporous and microporous membrane films of several materials including electrolyte materials. This paper discussed the use of a colloidal sol to create a first layer on top of a standard Julich coatmix-substrate with the spin-coating technique. The experimental methods were described with particular reference to the electrochemical characterization of cells produced; synchronization of roll-coating transport; and scanning electron microscopy. It was concluded that thin-film technologies like sol-gel, roll-coating and physical vapour phase deposition are promising candidates for producing SOFCs with high-performance at low operating temperatures. It was possible to demonstrate the potential of thin film technology for sputtered strontium-diffusion barriers, but optimization of the current ceramic coating methods is still necessary for the electrolyte layers. 3 refs., 8 figs.

  9. Soot Surface Oxidation in Laminar Hydrocarbon/Air Diffusion Flames at Atmospheric Pressure. Appendix I

    Science.gov (United States)

    Xu, F.; El-Leathy, A. M.; Kim, C. H.; Faeth, G. M.; Yuan, Z.-G. (Technical Monitor); Urban, D. L. (Technical Monitor); Yuan, Z.-G. (Technical Monitor)

    2003-01-01

    Soot surface oxidation was studied experimentally in laminar hydrocarbon/air diffusion flames at atmospheric pressure. Measurements were carried out along the axes of round fuel jets burning in coflowing dry air considering acetylene-nitrogen, ethylene, propyiene-nitrogen, propane and acetylene-benzene-nitrogen in the fuel stream. Measurements were limited to the initial stages of soot oxidation (carbon consumption less than 70%) where soot oxidation occurs at the surface of primary soot particles. The following properties were measured as a function of distance above the burner exit: soot concentrations by deconvoluted laser extinction, soot temperatures by deconvoluted multiline emission, soot structure by thermophoretic sampling and analysis using Transmission Electron Microscopy (TEM), concentrations of major stable gas species (N2, H2O, H2, O2, CO, CO2, CH4, C2H2, C2H6, C3H6, C3H8, and C6H6) by sampling and gas chromatography, concentrations of some radical species (H, OH, O) by deconvoluted Li/LiOH atomic absorption and flow velocities by laser velocimetry. For present test conditions, it was found that soot surface oxidation rates were not affected by fuel type, that direct rates of soot surface oxidation by O2 estimated from Nagle and Strickland-Constable (1962) were small compared to observed soot surface oxidation rates because soot surface oxidation was completed near the flame sheet where O2 concentrations were less than 3% by volume, and that soot surface oxidation rates were described by the OH soot surface oxidation mechanism with a collision efficiency of 0.14 and an uncertainty (95% confidence) of +/- 0.04 when allowing for direct soot surface oxidation by O2, which is in reasonably good agreement with earlier observations of soot surface oxidation rates in both premixed and diffusion flames at atmospheric pressure.

  10. Kinetics of wet air oxidation of glyoxalic acid and oxalic acid

    Energy Technology Data Exchange (ETDEWEB)

    Shende, R.V.; Mahajani, V.V. (Univ. of Bombay (India). Dept. of Chemical Technology)

    1994-12-01

    Oxidation of lower molecular weight monobasic and dibasic acids such as formic acid, acetic acid, glyoxalic acid, and oxalic acid is often the rate-controlling step during wet air oxidation (WAO) of an aqueous waste stream exhibiting very high chemical oxygen demand (COD). The kinetics of WAO of glyoxalic acid and oxalic acid was studied in absence and presence of a cupric sulfate catalyst in the temperature range of 120--245 C and oxygen partial pressure of 0.345--1.380 MPa. The wet oxidation of oxalic acid was found to require more severe conditions as compared to glyoxalic acid. The reaction mechanism and kinetic model have been discussed.

  11. Innovative Clean Coal Technology (ICCT): 500-MW demonstration of advanced wall-fired cmbustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Field chemical emissions monitoring, Overfire air and overfire air/low NO{sub x} burner operation: Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    This report summarizes data gathered by Radian Corporation at a coal-fired power plant, designated Site 16, for a program sponsored by the United States Department of Energy (DOE), Southern Company Services (SCS), and the Electric Power Research Institute (EPRI). Concentrations of selected inorganic and organic substances were measured in the process and discharge streams of the plant operating under two different types of combustion modifications: overfire air (OFA) and a combination of overfire air with low-NO{sub x} burners (OFA/LNB). Information contained in this report will allow DOE and EPRI to determine the effects of low-NO{sub x} modifications on plant emissions and discharges. Sampling was performed on an opposed wall-fired boiler burning medium-sulfur bituminous coal. Emissions were controlled by electrostatic precipitators (ESPs). The testing was conducted in two distinct sampling periods, with the OFA test performed in March of 1991 and the OFA/LNB test performed in May of 1993. Specific objectives were: to quantify emissions of target substances from the stack; to determine the efficiency of the ESPs for removing the target substances; and to determine the fate of target substances in the various plant discharge streams.

  12. Some technological aspects of methane aromatization (direct and via oxidative coupling)

    Energy Technology Data Exchange (ETDEWEB)

    Skutil, Krzysztof; Taniewski, Marian [Silesian Technical University, Chair of Chemical Organic Technology and Petrochemistry, ul. Krzywoustego 4, 44-101 Gliwice (Poland)

    2006-06-15

    The investigations on transformation of methane to benzene and naphthalene have been carried out in aim to verify and supplement earlier reported data and on this basis to estimate real industrial perspectives of the CH{sub 4} aromatization concept, the main challenges and barriers. Methane aromatization (direct and via oxidative coupling) has been studied over Mo/HZSM-5 catalyst used both for direct methane dehydroaromatization and for aromatization of methane oxidative coupling (OCM) products. The effects of Mo content in the catalyst, temperature, space velocity, the presence of CO{sub 2}, CO, H{sub 2}O, C{sub 2}H{sub 4}, C{sub 2}H{sub 6} and their mixtures in the feed have been studied. The effectiveness of the catalyst regeneration in the air was also examined. All results were confronted with the literature data and analyzed from technological point of view. It was confirmed that direct CH{sub 4} aromatization process was characterized by a low CH{sub 4} single-pass conversion, low single-pass yields of the main products (benzene, hydrogen and naphthalene) and a low catalyst stability (rapid catalyst deactivation). Various possible technological schemes were analyzed. It was concluded that real industrial chances of direct methane aromatization or aromatization via OCM would depend largely on the advancement in the cost-effective separation techniques. The methane aromatization concept was also confronted with other methane conversion processes. (author)

  13. COST ANALYSIS OF ACTIVATED CARBON VERSUS PHOTOCATALYTIC OXIDATION FOR REMOVING ORGANIC COMPOUNDS FROM INDOOR AIR

    Science.gov (United States)

    A cost comparison has been conducted of 1 m3/s indoor air cleaners using granular activated carbon (GAC) vs. photocatalytic oxidation (PCO) for treating a steady-state inlet volatile organic compound (VOC) concentration of 0.3 mg/m3. The commercial GAC unit was costed assuming t...

  14. Galvanic detection of sulfur dioxide in ambient air at trace levels by anodic oxidation

    NARCIS (Netherlands)

    Lindqvist, F.

    1978-01-01

    A continuous method for the measurement of SO2 in ambient air at trace levels is described. The principle of detection is based on the anodic oxidation of SO2 in a galvanic cell. A differential measuring technique with a cell with two anodes and one cathode is used; background and noise current are

  15. Technology Solutions Case Study: Air Leakage and Air Transfer Between Garage and Living Space, Waldorf, Maryland

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-11-01

    In this project, Building Science Corporation worked with production homebuilder K. Hovnanian to evaluate air transfer between the garage and living space in a single-family detached home constructed by a production homebuilder in compliance with the 2009 International Residential Code and the 2009 International Energy Conservation Code. The project gathered important information about the performance of whole-building ventilation systems and garage ventilation systems as they relate to minimizing flow of contaminated air from garage to living space. A series of 25 multipoint fan pressurization tests and additional zone pressure diagnostic testing measured the garage and house air leakage, the garage-to-house air leakage, and garage and house pressure relationships to each other and to outdoors using automated fan pressurization and pressure monitoring techniques. While the relative characteristics of this house may not represent the entire population of new construction configurations and air tightness levels (house and garage) throughout the country, the technical approach was conservative and should reasonably extend the usefulness of the results to a large spectrum of house configurations from this set of parametric tests in this one house. Based on the results of this testing, the two-step garage-to-house air leakage test protocol described above is recommended where whole-house exhaust ventilation is employed. For houses employing whole-house supply ventilation (positive pressure) or balanced ventilation (same pressure effect as the baseline condition), adherence to the EPA Indoor airPLUS house-to-garage air sealing requirements should be sufficient to expect little to no garage-to-house air transfer.

  16. Synthesis and characterization of carbon black/manganese oxide air cathodes for zinc-air batteries

    Science.gov (United States)

    Li, Po-Chieh; Hu, Chi-Chang; Lee, Tai-Chou; Chang, Wen-Sheng; Wang, Tsin Hai

    2014-12-01

    Due to the poor electric conductivity but the excellent catalytic ability for the oxygen reduction reaction (ORR), manganese dioxide in the α phase (denoted as α-MnO2) anchored onto carbon black powders (XC72) has been synthesized by the reflux method. The specific surface area and electric conductivity of the composites are generally enhanced by increasing the XC72 content while the high XC72 content will induce the formation of MnOOH which shows a worse ORR catalytic ability than α-MnO2. The ORR activity of such air cathodes have been optimized at the XC72/α-MnO2 ratio equal to 1 determined by the thermogravimetric analysis. By using this optimized cathode under the air atmosphere, the quasi-steady-state full-cell discharge voltages are equal to 1.353 and 1.178 V at 2 and 20 mA cm-2, respectively. Due to the usage of ambient air rather than pure oxygen, this Zn-air battery shows a modestly high discharge peak power density (67.51 mW cm-2) meanwhile the power density is equal to 47.22 mW cm-2 and the specific capacity is more than 750 mAh g-1 when this cell is operated at 1 V.

  17. Measurement and improvement of indoor air quality in an information technology classroom

    Directory of Open Access Journals (Sweden)

    Tomić Mladen A.

    2014-01-01

    Full Text Available With the rapid development of information technology equipment and its use in the teaching and learning activities, the working environment (especially indoor air quality in which students and pupils spend a great deal of time in educational institutions has been changing. Therefore, special attention must be paid to indoor air quality and comfort. It is of great importance to maintain indoor air quality in an object, such as information technology classrooms, where a large number of students spend long periods of time. Poor indoor environment can negatively affect scholarly performances and cause discomfort and poor work performance. The problem of indoor air quality in educational institutions can be more serious than in other types of objects, because of the higher concentration of students and information technology equipment. This paper analyzes the changes in air quality in an information technology classrooms, when occupied with students, for the period from March to April. The changes of indoor air temperature, relative humidity, and carbon dioxide concentration are monitored in the classroom, as well as outdoor temperature and relative humidity. Several cases are studied: the classroom with closed windows and doors (closed classroom, the classroom with natural ventilation, the classroom cooled with a split system (cooled classroom. Responses of students are followed for each case. The analysis is performed based on the measurement results and numerical simulations using the computational fluid dynamics package, and measures are proposed to improve the indoor air quality in the considered classroom.

  18. Towards Personal Exposures: How Technology Is Changing Air Pollution and Health Research.

    Science.gov (United States)

    Larkin, A; Hystad, P

    2017-10-05

    We present a review of emerging technologies and how these can transform personal air pollution exposure assessment and subsequent health research. Estimating personal air pollution exposures is currently split broadly into methods for modeling exposures for large populations versus measuring exposures for small populations. Air pollution sensors, smartphones, and air pollution models capitalizing on big/new data sources offer tremendous opportunity for unifying these approaches and improving long-term personal exposure prediction at scales needed for population-based research. A multi-disciplinary approach is needed to combine these technologies to not only estimate personal exposures for epidemiological research but also determine drivers of these exposures and new prevention opportunities. While available technologies can revolutionize air pollution exposure research, ethical, privacy, logistical, and data science challenges must be met before widespread implementations occur. Available technologies and related advances in data science can improve long-term personal air pollution exposure estimates at scales needed for population-based research. This will advance our ability to evaluate the impacts of air pollution on human health and develop effective prevention strategies.

  19. Correlation between the microstructures of graphite oxides and their catalytic behaviors in air oxidation of benzyl alcohol.

    Science.gov (United States)

    Geng, Longlong; Wu, Shujie; Zou, Yongcun; Jia, Mingjun; Zhang, Wenxiang; Yan, Wenfu; Liu, Gang

    2014-05-01

    A series of graphite oxide (GO) materials were obtained by thermal treatment of oxidized natural graphite powder at different temperatures (from 100 to 200 °C). The microstructure evolution (i.e., layer structure and surface functional groups) of the graphite oxide during the heating process is studied by various characterization means, including XRD, N2 adsorption, TG-DTA, in situ DRIFT, XPS, Raman, TEM and Boehm titration. The characterization results show that the structures of GO materials change gradually from multilayer sheets to a transparent ultrathin 2D structure of the carbon sheets. The concentration of surface COH and HOCO groups decrease significantly upon treating temperature increasing. Benzyl alcohol oxidation with air as oxidant source was carried out to detect the catalytic behaviors of different GO materials. The activities of GO materials decrease with the increase of treating temperatures. It shows that the structure properties, including ultrathin sheets and high specific surface area, are not crucial factors affecting the catalytic activity. The type and amount of surface oxygen-containing functional groups of GO materials tightly correlates with the catalytic performance. Carboxylic groups on the surface of GO should act as oxidative sites for benzyl alcohol and the reduced form could be reoxidized by molecular oxygen. Copyright © 2014 Elsevier Inc. All rights reserved.

  20. Technology & Mechanics Overview of Air-Inflated Fabric Structures

    Science.gov (United States)

    2006-12-04

    bridging, and energy absorbers such as automotive air bags and landing cushions for space vehicles. Recent advances in high performance fibers and...inflated fabric structures were constructed using adhesively bonded, piece-cut manufacturing methods. These methods were limited to relatively low...moisture, fire, chemicals, etc. Coating materials such as urethane , PVC (poly vinyl chloride), neoprene, EPDM (ethylene propylene diene monomer) are

  1. Magnetic Refrigeration Technology for High Efficiency Air Conditioning

    Energy Technology Data Exchange (ETDEWEB)

    Boeder, A; Zimm, C

    2006-09-30

    Magnetic refrigeration was investigated as an efficient, environmentally friendly, flexible alternative to conventional residential vapor compression central air conditioning systems. Finite element analysis (FEA) models of advanced geometry active magnetic regenerator (AMR) beds were developed to minimize bed size and thus magnet mass by optimizing geometry for fluid flow and heat transfer and other losses. Conventional and magnetocaloric material (MCM) regenerator fabrication and assembly techniques were developed and advanced geometry passive regenerators were built and tested. A subscale engineering prototype (SEP) magnetic air conditioner was designed, constructed and tested. A model of the AMR cycle, combined with knowledge from passive regenerator experiments and FEA results, was used to design the regenerator beds. A 1.5 Tesla permanent magnet assembly was designed using FEA and the bed structure and plenum design was extensively optimized using FEA. The SEP is a flexible magnetic refrigeration platform, with individually instrumented beds and high flow rate and high frequency capability, although the current advanced regenerator geometry beds do not meet performance expectations, probably due to manufacturing and assembly tolerances. A model of the AMR cycle was used to optimize the design of a 3 ton capacity magnetic air conditioner, and the system design was iterated to minimize external parasitic losses such as heat exchanger pressure drop and fan power. The manufacturing cost for the entire air conditioning system was estimated, and while the estimated SEER efficiency is high, the magnetic air conditioning system is not cost competitive as currently configured. The 3 ton study results indicate that there are other applications where magnetic refrigeration is anticipated to have cost advantages over conventional systems, especially applications where magnetic refrigeration, through the use of its aqueous heat transfer fluid, could eliminate intermediate

  2. The benefit of solid oxide fuel cells with integrated air pre-heater

    Energy Technology Data Exchange (ETDEWEB)

    Costamagna, P. [Univ. degli Studi di Genova, Fac. di Ingegneria, ISTIC, Inst. di Ingegneria Chimica e di Processo `G.B. Bonino`, Genova (Italy)

    1997-11-01

    A new design has recently been proposed in the field of solid oxide fuel cells, consisting of a traditional electrochemical cell integrated with a pre-heater. In this paper a simulation model for the rectangular planar solid oxide fuel cell with integrated air pre-heater is presented. A two-dimensional stack simulation is presented as well, one axis coincides with the fuel flow direction, the other with the stack height. Local quantities such as current density, gas and solid temperatures are reported and cell characteristics predicted. In a parameter study, effects of oxygen utilisation and heat-transfer conditions in the pre-heater on the local temperature distribution of the solid structure are considered. As a result, the benefit of the new cell design becomes evident when low air flow rates are applied. A further advantage associated with the reduced flow rate is the low air temperature at the inlet. (orig.)

  3. From particles to patients: oxidative stress and the cardiovascular effects of air pollution.

    Science.gov (United States)

    Miller, Mark R; Shaw, Catherine A; Langrish, Jeremy P

    2012-07-01

    Air pollution, especially airborne particulate matter (PM), is associated with an increase in both morbidity and mortality from cardiovascular disease, although the underlying mechanisms remain incompletely established. The one consistent observation that links the pulmonary and cardiovascular effects of inhaled PM is oxidative stress. This article examines the evidence for the role of oxidative stress in the cardiovascular effects of air pollution, beginning with observations from epidemiological and controlled exposure studies and then exploring potential mechanistic pathways involving free radical generation from PM itself, to effects of PM on cell cultures, isolated organs, healthy animals and animal models of disease. Particular emphasis is placed on the vascular and atherosclerotic effects of urban air pollution and diesel exhaust emissions as rich sources of environmental ultrafine particles.

  4. 77 FR 41930 - Bleed Air Cleaning and Monitoring Equipment and Technology

    Science.gov (United States)

    2012-07-17

    ... an opportunity to participate in #0;the rule making prior to the adoption of the final rules. #0; #0... Equipment and Technology ACTION: Notice; request for information. SUMMARY: The FAA seeks information from industry developers, manufacturers, and the public related to effective air cleaning technology and...

  5. Proceedings of the 1993 non-fluorocarbon insulation, refrigeration and air conditioning technology workshop

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    Sessions included: HFC blown polyurethanes, carbon dioxide blown foam and extruded polystyrenes, plastic foam insulations, evacuated panel insulation, refrigeration and air conditioning, absorption and adsorption and stirling cycle refrigeration, innovative cooling technologies, and natural refrigerants. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

  6. Air-Based Remediation Workshop - Section 8 Air-Based Remediation Technology Selection Logic

    Science.gov (United States)

    Pursuant to the EPA-AIT Implementing Arrangement 7 for Technical Environmental Collaboration, Activity 11 "Remediation of Contaminated Sites," the USEPA Office of International Affairs Organized a Forced Air Remediation Workshop in Taipei to deliver expert training to the Environ...

  7. Use of Air2Air Technology to Recover Fresh-Water from the Normal Evaporative Cooling Loss at Coal-Based Thermoelectric Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Ken Mortensen

    2009-06-30

    This program was undertaken to build and operate the first Air2Air{trademark} Water Conservation Cooling Tower at a power plant, giving a validated basis and capability for water conservation by this method. Air2Air{trademark} water conservation technology recovers a portion of the traditional cooling tower evaporate. The Condensing Module provides an air-to-air heat exchanger above the wet fill media, extracting the heat from the hot saturated moist air leaving in the cooling tower and condensing water. The rate of evaporate water recovery is typically 10%-25% annually, depending on the cooling tower location (climate).

  8. Copper oxide as efficient catalyst for oxidative dehydrogenation of alcohols with air

    DEFF Research Database (Denmark)

    Poreddy, Raju; Engelbrekt, Christian; Riisager, Anders

    2015-01-01

    The oxidative dehydrogenation of alcohols to carbonyl compounds was studied using CuO nanoparticle catalysts prepared by solution synthesis in buffered media. CuO nanoparticles synthesized in N-cyclohexyl- 3-aminopropanesulfonic acid buffer showed high catalytic activity for the oxidation...

  9. Impact of Air Pollutants on Oxidative Stress in Common Autophagy-Mediated Aging Diseases

    Directory of Open Access Journals (Sweden)

    Mohamed Saber Numan

    2015-02-01

    Full Text Available Atmospheric pollution-induced cellular oxidative stress is probably one of the pathogenic mechanisms involved in most of the common autophagy-mediated aging diseases, including neurodegenerative diseases such as amyotrophic lateral sclerosis (ALS, Alzheimer’s, disease, as well as Paget’s disease of bone with or without frontotemporal dementia and inclusion body myopathy. Oxidative stress has serious damaging effects on the cellular contents: DNA, RNA, cellular proteins, and cellular organelles. Autophagy has a pivotal role in recycling these damaged non-functional organelles and misfolded or unfolded proteins. In this paper, we highlight, through a narrative review of the literature, that when autophagy processes are impaired during aging, in presence of cumulative air pollution-induced cellular oxidative stress and due to a direct effect on air pollutant, autophagy-mediated aging diseases may occur.

  10. Exposure to Ultrafine Particles from Ambient Air and Oxidative Stress-Induced DNA Damage

    DEFF Research Database (Denmark)

    Bräuner, Elvira Vaclavik; Forchhammer, Lykke; Møller, Peter

    2007-01-01

    BACKGROUND: Particulate matter, especially ultrafine particles (UFPs), may cause health effects through generation of oxidative stress, with resulting damage to DNA and other macromolecules. OBJECTIVE: We investigated oxidative damage to DNA and related repair capacity in peripheral blood...... mononuclear cells (PBMCs) during controlled exposure to urban air particles with assignment of number concentration (NC) to four size modes with average diameters of 12, 23, 57, and 212 nm. DESIGN. Twenty-nine healthy adults participated in a randomized, two-factor cross-over study with or without biking...... exercise for 180 min and with exposure to particles (NC 6169-15362/cm3) or filtered air (NC 91-542/cm3) for 24 hr. METHODS: The levels of DNA strand breaks (SBs), oxidized purines as formamidopyrimidine DNA glycolase (FPG) sites, and activity of 7,8-dihydro-8-oxoguanine-DNA glycosylase (OGG1) in PBMCs were...

  11. Effect of Naturally Occurring Ozone Air Pollution Episodes on Pulmonary Oxidative Stress and Inflammation

    Directory of Open Access Journals (Sweden)

    Cheryl Pirozzi

    2015-05-01

    Full Text Available This study aimed to determine if naturally occurring episodes of ozone air pollution in the Salt Lake Valley in Utah, USA, during the summer are associated with increased pulmonary inflammation and oxidative stress, increased respiratory symptoms, and decreased lung function in individuals with chronic obstructive pulmonary disease (COPD compared to controls. We measured biomarkers (nitrite/nitrate (NOx, 8-isoprostane in exhaled breath condensate (EBC, spirometry, and respiratory symptoms in 11 former smokers with moderate-to-severe COPD and nine former smokers without airflow obstruction during periods of low and high ozone air pollution. High ozone levels were associated with increased NOx in EBC in both COPD (8.7 (±8.5 vs. 28.6 (±17.6 μmol/L on clean air vs. pollution days, respectively, p < 0.01 and control participants (7.6 (±16.5 vs. 28.5 (±15.6 μmol/L on clean air vs. pollution days, respectively, p = 0.02. There was no difference in pollution effect between COPD and control groups, and no difference in EBC 8-isoprostane, pulmonary function, or respiratory symptoms between clean air and pollution days in either group. Former smokers both with and without airflow obstruction developed airway oxidative stress and inflammation in association with ozone air pollution episodes.

  12. Technology assessment of vertical and horizontal air drilling potential in the United States. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Carden, R.S.

    1993-08-18

    The objective of the research was to assess the potential for vertical, directional and horizontal air drilling in the United States and to evaluate the current technology used in air drilling. To accomplish the task, the continental United States was divided into drilling regions and provinces. The map in Appendix A shows the divisions. Air drilling data were accumulated for as many provinces as possible. The data were used to define the potential problems associated with air drilling, to determine the limitations of air drilling and to analyze the relative economics of drilling with air versus drilling mud. While gathering the drilling data, operators, drilling contractors, air drilling contractors, and service companies were contacted. Their opinion as to the advantages and limitations of air drilling were discussed. Each was specifically asked if they thought air drilling could be expanded within the continental United States and where that expansion could take place. The well data were collected and placed in a data base. Over 165 records were collected. Once in the data base, the information was analyzed to determine the economics of air drilling and to determine the limiting factors associated with air drilling.

  13. Sea-to-air and diapycnal nitrous oxide fluxes in the eastern tropical North Atlantic Ocean

    Directory of Open Access Journals (Sweden)

    A. Kock

    2012-03-01

    Full Text Available Sea-to-air and diapycnal fluxes of nitrous oxide (N2O into the mixed layer were determined during three cruises to the upwelling region off Mauritania. Sea-to-air fluxes as well as diapycnal fluxes were elevated close to the shelf break, but elevated sea-to-air fluxes reached further offshore as a result of the offshore transport of upwelled water masses. To calculate a mixed layer budget for N2O we compared the regionally averaged sea-to-air and diapycnal fluxes and estimated the potential contribution of other processes, such as vertical advection and biological N2O production in the mixed layer. Using common parameterizations for the gas transfer velocity, the comparison of the average sea-to-air and diapycnal N2O fluxes indicated that the mean sea-to-air flux is about three to four times larger than the diapycnal flux. Neither vertical and horizontal advection nor biological production were found sufficient to close the mixed layer budget. Instead, the sea-to-air flux, calculated using a parameterization that takes into account the attenuating effect of surfactants on gas exchange, is in the same range as the diapycnal flux. From our observations we conclude that common parameterizations for the gas transfer velocity likely overestimate the air-sea gas exchange within highly productive upwelling zones.

  14. Isolated Islands by Selective Local Oxidation (islo): a Silicon-On (soi) Technology for Nanoelectronic and Nanoelectromechanical Applications.

    Science.gov (United States)

    Arney, Susanne Christine

    The development of an advanced fully-integrated nanometer-scale isolation technology called the Isolated Islands of Substrate-Silicon by Selective Lateral Oxidation (ISLO) technology is reported. The versatility and applicability of the ISLO technology for diverse nanoelectronic and nanoelectromechanical devices and systems are described relative to the challenging issues of isolation and contacts. The basic ISLO structure is fabricated using electron beam lithography and standard VLSI reactive ion etching and oxidation processes. Single crystal silicon (SCS) islands 100-300-nm-wide, and 500 -2000-nm-tall are electrically and thermally isolated from the underlying substrate by selective lateral thermal oxidation at the base of the islands. Dislocation-free fully-isolated islands are obtained. Full-isolation of the basic ISLO structure depends on island linewidth, oxidation-masking film thicknesses, recess etch profile, and oxidation time and temperature. The extended ISLO technology provides 100-nm-wide, movable, suspended, high stiffness, low mass, SCS or SCS-dielectric-composite beam segments with integrated electrical contacts and metallization for high frequency (5-10 MHz) nanodynamic applications. Fixed or cantilevered beam segments are isolated from the underlying substrate -silicon by thermally grown oxide or an air-bridge. Wedge -pairs or tip-pairs vertically opposed across the isolation oxide or air-bridge have application to electron tunneling or field emission devices. A selectively-sharpened tip -above-a-tip structure is formed at the intersection of cantilevered beam segments. Vertical triple-tip and quadruple -tip structures are demonstrated. A new deep-submicron self-aligned sidewall source/drain, top-surface gate Thin -Film-Silicon-On-Insulator (TFSOI) MOSFET (ISLO FET) based on the inherently three-dimensional, non-planar ISLO structure is presented. Stress-related defect generation and dopant segregation during the oxidation, erosion of the high

  15. Air Force Laboratory’s 2005 Technology Milestones

    Science.gov (United States)

    2006-01-01

    as well as advanced high-power cooling technology demonstrations required for high-power microwave anode. Background AFRL researches, develops... germination period has not prevented physicists, chemists, biologists, and doctors from quickly embracing the technology. Payoff AFRL sponsored Dr. James...electromagnetic waves, THz frequencies are located between microwaves and infrared frequencies. THz frequencies are 100 to 1,000 times lower in frequency than

  16. Technology and the Air Force: A Retrospective Assessment

    Science.gov (United States)

    1997-01-01

    environment, the French philosopher Jean Paul Sartre , som- berly remarking on the universe in general, postulated that, “Existence precedes essence,” that... Paul Sartre , with a little bit of Woody Allen thrown in. One advantage of being the commander of the History Support Office is that the Air Force...Development of Modern Aviation (London: Routledge & Kegan Paul , 1968), pp 47-97; Robert Schlaifer, Development of Aircraft Engines (Boston: Harvard

  17. The impact of European legislative and technology measures to reduce air pollutants on air quality, human health and climate

    Science.gov (United States)

    Turnock, S. T.; Butt, E. W.; Richardson, T. B.; Mann, G. W.; Reddington, C. L.; Forster, P. M.; Haywood, J.; Crippa, M.; Janssens-Maenhout, G.; Johnson, C. E.; Bellouin, N.; Carslaw, K. S.; Spracklen, D. V.

    2016-02-01

    European air quality legislation has reduced emissions of air pollutants across Europe since the 1970s, affecting air quality, human health and regional climate. We used a coupled composition-climate model to simulate the impacts of European air quality legislation and technology measures implemented between 1970 and 2010. We contrast simulations using two emission scenarios; one with actual emissions in 2010 and the other with emissions that would have occurred in 2010 in the absence of technological improvements and end-of-pipe treatment measures in the energy, industrial and road transport sectors. European emissions of sulphur dioxide, black carbon (BC) and organic carbon in 2010 are 53%, 59% and 32% lower respectively compared to emissions that would have occurred in 2010 in the absence of legislative and technology measures. These emission reductions decreased simulated European annual mean concentrations of fine particulate matter (PM2.5) by 35%, sulphate by 44%, BC by 56% and particulate organic matter by 23%. The reduction in PM2.5 concentrations is calculated to have prevented 80 000 (37 000-116 000, at 95% confidence intervals) premature deaths annually across the European Union, resulting in a perceived financial benefit to society of US232 billion annually (1.4% of 2010 EU GDP). The reduction in aerosol concentrations due to legislative and technology measures caused a positive change in the aerosol radiative effect at the top of atmosphere, reduced atmospheric absorption and also increased the amount of solar radiation incident at the surface over Europe. We used an energy budget approximation to estimate that these changes in the radiative balance have increased European annual mean surface temperatures and precipitation by 0.45 ± 0.11 °C and by 13 ± 0.8 mm yr-1 respectively. Our results show that the implementation of European legislation and technological improvements to reduce the emission of air pollutants has improved air quality and human

  18. U.S. EPA-developed air-pollution control technology

    Energy Technology Data Exchange (ETDEWEB)

    Lee, V.S. [Seoul Sharp-Center for the Environment & Development, Research Triangle Park, NC (United States)

    1994-09-01

    The U.S. Environmental Protection Agency has licensed, for marketing on a world-wide exclusive basis, five air pollution technologies that utilize electrostatic precipitators. The technologies are the SUPER ESP, the reentrainment suppressor, spray drying within an existing ESP for simultaneous sulphur dioxide and particulate matter capture (E-SO{sub x}), electrostatic fabric filtration (ESFF), and retrofit electrostatic filtration (REF). The technical and operational capabilities of these technologies are described. 14 refs., 10 figs.

  19. Commercialization and development of U.S. EPA-developed air pollution control technologies

    Energy Technology Data Exchange (ETDEWEB)

    Lee, V.S. [Seoul Sharp-Center for the Environment & Development, Research Triangle Park, NC (United States)

    1994-09-01

    Several air pollution technologies that are related to electrostatic precipitators and were developed by the U.S. Environmental Protection Agency, have been licensed for marketing. The five technologies are the SUPER ESP, the reentrainment suppressor, spray drying within an existing ESP (E-SO{sub x}), retrofit electrostatic filtration (REF), and electrostatically augmented fabric filtration (ESFF). A marketing strategy for these technologies is described. 1 ref., 1 fig.

  20. Air cushion furnace technology for heat treatment of high quality aluminum alloy auto body sheet

    Institute of Scientific and Technical Information of China (English)

    Li Yong; Wang Zhaodong; Ma Mingtu; Wang Guodong; Fu Tianliang; Li Jiadong; Liang Xiong

    2014-01-01

    The process characteristics of heat treatment of aluminum alloy auto body sheet and the working prin-ciple of air cushion furnace were introduced. The process position and irreplaceable role of air cushion furnace in the aluminum alloy auto body sheet production was pointed out after the difficulty and key points in the whole production process of auto body sheet were studied. Then the development process of air cushion furnace line of aluminum alloy sheet was reviewed,summarized and divided to two stages. Based on the research of air cushion furnace,the key technology of it was analyzed,then the key points on process,equipment and control models of air cushion furnace for aluminum alloy auto body sheet in future were put forward. With the rapid de-velopment of automotive industry,there will be certainly a new upsurge of research and application of air cush-ion furnace for heat treatment of aluminum alloy auto body sheet.

  1. Changes in optical properties of coals during air oxidation at moderate temperature

    Energy Technology Data Exchange (ETDEWEB)

    Calemma, V.; Del Piero, G.; Rausa, R.; Girardi, E. [Eniricerche SpA, Milan (Italy)

    1995-03-01

    Montana Rosebud coal and North Dakota lignite have been oxidized in a fluidized bed reactor at 200{degree}C, with air at 0.2, 0.6 and 1 MPa for reaction times up to 4 h. Oxidized samples were analyzed by reflected light microscopy to investigate the variation of reflectance, formation of rims and changes in maceral morphology. The most remarkable changes concerned the vitrinite. Exinite exhibited an increase of reflectance, but this was not measurable owing to the small size of the fragments. The results indicate that the increase of reflectance at 200{degree}C is only partially dependent on chemical changes caused by oxidation. Data show the existence of threshold oxidation degree, beyond which the reflectance is not affected by further chemical changes occurring in the coal structure. Furthermore, the changes in elemental composition associated with the degree of threshold oxidation are relatively small. During oxidation both Montana Rosebud coal and North Dakota lignite exhibit the formation of rims, but with large differences as regards the size of the phenomenon. The decreased percentage of vitrinite fragments with rims at higher air pressures, and the relationships between the width of rims and reaction time at the three pressures used, support the view that formation of rims occurs when the reaction rate is controlled by the diffusion of oxygen. During reaction, the telinitic structure of vitrinite tends to disappear to assume a collinitic appearance. 22 refs., 8 figs., 2 tabs.

  2. Synthesis and characterization of carbon black/manganese oxide air cathodes for zinc-air batteries: Effects of the crystalline structure of manganese oxides

    Science.gov (United States)

    Li, Po-Chieh; Hu, Chi-Chang; Noda, Hiroyuki; Habazaki, Hiroki

    2015-12-01

    Manganese oxides (MnOx) in α-, β-, γ-, δ-MnO2 phases, Mn3O4, Mn2O3, and MnOOH are synthesized for systematically comparing their electrocatalytic activity of the oxygen reduction reaction (ORR) in the Zn-air battery application. The optimal MnOx/XC-72 mass ratio for the ORR is equal to 1 and the oxide crystalline structure effect on the ORR is compared. The order of composites with respect to decreasing the ORR activity is: α-MnO2/XC-72 > γ-MnO2/XC-72 > β-MnO2/XC-72 > δ-MnO2/XC-72 > Mn2O3/XC-72 > Mn3O4/XC-72 > MnOOH/XC-72. The textural properties of MnOx are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption isotherms with Brunauer-Emmett-Teller (BET) analysis, X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Electrochemical studies include linear sweep voltammetry (LSV), rotating ring-disk electrode (RRDE) voltammetry, and the full-cell discharge test. The discharge peak power density of Zn-air batteries varies from 61.5 mW cm-2 (α-MnO2/XC-72) to 47.1 mW cm-2 (Mn3O4/XC-72). The maximum peak power density is 102 mW cm-2 for the Zn-air battery with an air cathode containing α-MnO2/XC-72 under an oxygen atmosphere when the carbon paper is 10AA. The specific capacity of all full-cell tests is higher than 750 mAh g-1 at all discharge current densities.

  3. Uranium Metal to Oxide Conversion by Air Oxidation –Process Development

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, A

    2001-12-31

    Published technical information for the process of metal-to-oxide conversion of uranium components has been reviewed and summarized for the purpose of supporting critical decisions for new processes and facilities for the Y-12 National Security Complex. The science of uranium oxidation under low, intermediate, and high temperature conditions is reviewed. A process and system concept is outlined and process parameters identified for uranium oxide production rates. Recommendations for additional investigations to support a conceptual design of a new facility are outlined.

  4. Soot Oxidation in Laminar Hydrocarbon/Air Diffusion Flames at Atmospheric Pressure. Appendix D

    Science.gov (United States)

    Xu, F.; El-Leathy, A. M.; Faeth, G. M.

    2000-01-01

    Soot oxidation was studied experimentally in laminar hydrocarbon/air diffusion flames at atmospheric pressure. Measurements were carried out along the axes of round jets burning in coflowing air considering acetylene, ethylene, proplyene and propane as fuels. Measurements were limited to the initial stages of soot oxidation (carbon consumption less than 70%) where soot oxidation mainly occurs at the surface of primary soot particles. The following properties were measured as a function of distance above the burner exit: soot concentrations by deconvoluted laser extinction, soot temperatures by deconvoluted multiline emission, soot structure by thermophoretic sampling and analysis using Transmission Electron Microscopy (TEM), concentrations of stable major gas species (N2, H2O, H2, 02, CO, CO2, CH4, C2H2, C2H4, C2H6, C3H6, and C3H8) by sampling and gas chromatography, concentrations of some radical species (H, OH, O) by the deconvoluted Li/LiOH atomic absorption technique and flow velocities by laser velocimetry. It was found that soot surface oxidation rates are not particularly affected by fuel type for laminar diffusion flames and are described reasonably well by the OH surface oxidation mechanism with a collision efficiency of 0.10, (standard deviation of 0.07) with no significant effect of fuel type in this behavior; these findings are in good agreement with the classical laminar premixed flame measurements of Neoh et al. Finally, direct rates of surface oxidation by O2 were small compared to OH oxidation for present conditions, based on estimated O2 oxidation rates due to Nagle and Strickland-Constable, because soot oxidation was completed near the flame sheet where O2 concentrations were less than 1.2% by volume.

  5. Soot Oxidation in Hydrocarbon/Air Diffusion Flames at Atmospheric Pressure. Appendix K

    Science.gov (United States)

    Xu, F.; El-Leathy, A. M.; Faeth, G. M.; Urban, D. L. (Technical Monitor); Yuan, Z.-G. (Technical Monitor)

    2001-01-01

    Soot oxidation was studied experimentally in laminar hydrocarbon/air diffusion flames at atmospheric pressure. Measurements were carried out along the axes of round jets burning in coflowing air considering acetylene, ethylene, propylene and propane as fuels. Measurements were limited to the initial stages of soot oxidation (carbon consumption less than 70%) where soot oxidation mainly occurs at the surface of primary soot particles. The following properties were measured as a function of distance above the burner exit: soot concentrations by deconvoluted laser extinction, soot temperatures by deconvoluted multiline emission, soot structure by thermophoretic sampling and analysis using Transmission Electron Microscopy (TEM), concentrations of stable major gas species (N2, H2O, H2, O2, CO, CO2, CH4, C2H2,C2H4, C2H6, C3H6, and C3H8) by sampling and gas chromatography, concentrations of some radical species (H, OH, O) by the deconvoluted Li/LiOH atomic absorption technique and flow velocities by laser velocimetry. It was found that soot surface oxidation rates are not particularly affected by fuel type for laminar diffusion flames and are described reasonably well by the OH surface oxidation mechanism with a collision efficiency of 0.10, (standard deviation of 0.07) with no significant effect of fuel type in this behavior; these findings are in good agreement with the classical laminar premixed flame measurements of Neoh et al. Finally, direct rates of surface oxidation by O2 were small compared to OH oxidation for present conditions, based on estimated O2 oxidation rates due to Nagle and Strickland-Constable (1962), because soot oxidation was completed near the flame sheet where O2 concentrations were less than 1.2% by volume.

  6. Conversion and Estrogenicity of 17β-estradiol During Photolytic/Photocatalytic Oxidation and Catalytic Wet-air Oxidation.

    Science.gov (United States)

    Bistan, Mirjana; Tišler, Tatjana; Pintar, Albin

    2012-06-01

    Estrogen 17β-estradiol (E2), produced by human body and excreted into municipal wastewaters, belongs to the group of endocrine disrupting compounds that are resistant to biological degradation. The aim of this study was to assess the efficiency of E2 removal from aqueous solutions by means of catalytic wet-air oxidation (CWAO) and photolytic/photocatalytic oxidation. CWAO experiments were conducted in a trickle-bed reactor at temperatures up to 230 °C and oxygen partial pressure of 10 bar over TiO2 and Ru/TiO2 solids. Photolytic/photocatalytic oxidation was carried out in a batch slurry reactor employing a TiO2 P-25 (Degussa) catalyst under visible or UV light. HPLC analysis and yeast estrogen screen assay were used to evaluate the removal of E2 and estrogenicity of treated samples. The latter was completely removed during photolytic/photocatalytic oxidation under UV (365 nm) light and photocatalytic oxidation under visible light. In CWAO experiments, complete removal of both E2 and estrogenicity from the feed solution were noticed in the presence of TiO2 and Ru/TiO2 catalysts.

  7. Oxidative stress and air pollution exposure during pregnancy: A molecular assessment.

    Science.gov (United States)

    Nagiah, S; Phulukdaree, A; Naidoo, D; Ramcharan, K; Naidoo, R N; Moodley, D; Chuturgoon, A

    2015-08-01

    Chronic air pollution exposure during pregnancy can cause oxidative stress leading to adverse birth outcomes. The aim of this study was to assess and compare oxidative stress response in peripheral lymphocytes isolated from pregnant women from a highly industrialized locale (south Durban (SD); n = 50) and a control with lower air pollutant levels (north Durban (ND); n = 50). Oxidative stress response was measured by quantifying malondialdehyde (MDA) levels and a SuperArray gene panel. Mitochondrial function (adenosine triphosphate (ATP) levels and mitochondrial depolarization), DNA integrity (comet assay and mitochondrial DNA (mtDNA) viability) and DNA repair (OGG1) were assessed. Antioxidant response was assessed by quantification of glutathione (GSH) and SOD2, nuclear factor erythroid 2-related factor 2 (Nrf2) and uncoupling protein 2 (UCP2) protein and messenger RNA (mRNA) expression. Levels of MDA (p = 0.9), mitochondrial depolarization (p = 0.88), ATP (1.89-fold), SOD2 (1.23-fold) and UCP2 (1.58-fold) gene expression were elevated in the SD group with significantly higher UCP2 protein levels (p = 0.05) and longer comet tail length (p = 0.0004). The expression of Nrf2 protein (p = 0.03) and mRNA levels (-1.37-fold), GSH concentration (p stress-related genes evaluated, 26 were differentially regulated. Pregnant women exposed to higher air pollutant levels showed increased markers for oxidative stress and compromised DNA integrity and repair. © The Author(s) 2014.

  8. Removal of Hg{sup 0} from flue gases in wet FGD by catalytic oxidation with air - An experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Andrej Stergarsek; Milena Horvat; Peter Frkal; Jost Stergarsek [' Jozef Stefan' Institute, Ljubljana (Slovenia)

    2010-11-15

    Research efforts are being focused on the development of mercury removal technologies, mainly directed to two alternative approaches: (I) the enhancement of homogeneous oxidation in the flue gases of Hg{sup 0} to water soluble Hg{sup 2+} by the addition of chlorides or bromides to the boiler or; (ii) the adsorption of Hg{sup 2+} and Hg{sup 0} on impregnated activated carbon (AC). A third option gaining more attention lately is based on the oxidation and retention of dissolved Hg{sup 0} in the wet flue gas desulphurisation (FGD) system. The experimental evidence of the present work showed that Hg{sup 0} present in the gaseous phase can be dissolved and oxidized to a high degree (70-90%) by air together with SO{sub 3}{sup 2-} in wet FGD solutions. Transition metals such as Fe{sup 2+} and Mn{sup 2+} act as catalysts, chloride enhances the reaction, while some oxosulphur compounds, e.g. tetrathionate, inhibit the oxidation. A combination of several catalysts at a concentration of sulphite (SO{sub 3}{sup 2-}) below 100 mg L{sup -1} and an adequate redox potential of the solution can assure reasonable mercury removal even in the presence of oxidation inhibiting compounds. The main competitive reactions that govern final Hg{sup 0} removal in the FGD are as follows: (1) oxidation of Hg{sup 0} together with SO{sub 2} with air, enhanced by catalysts; (2) removal of catalysts by precipitation in the form of Fe(OH){sub 3} and eventually as MnO{sub 2} (to overcome this problem continuous addition of catalysts to the solution is required); (3) reduction of Fe{sup 3+} by tetrathionate to Fe{sup 2+} which (4) may reduce Hg{sup 2+} to Hg{sup 0} and probably (5) the complexation of Hg{sup 2+} by anions present which may play an important role in the mechanism by complexing the product(s) of the Hg{sup 0} oxidation reaction. 35 refs., 10 figs., 7 tabs.

  9. Sea-to-air and diapycnal nitrous oxide fluxes in the eastern tropical North Atlantic Ocean

    Directory of Open Access Journals (Sweden)

    A. Kock

    2011-10-01

    Full Text Available Sea-to-air and diapycnal fluxes of nitrous oxide (N2O into the mixed layer were determined during three cruises to the upwelling region off Mauritania. Both fluxes were elevated close to the shelf break, but elevated sea-to-air fluxes reached further offshore as a result of the offshore transport of upwelled water masses. To calculate a mixed layer budget for N2O we compared the regionally averaged sea-to-air and diapycnal fluxes and estimated the potential contribution of other processes, such as vertical advection and biological N2O production in the mixed layer. Using common parameterizations for the gas transfer velocity, the comparison of the average sea-to-air and diapycnal N2O fluxes indicated that the mean sea-to-air flux is about three to four times larger than the diapycnal flux. Vertical and horizontal advection or biological production were found not sufficient to close the mixed layer budget. Instead, the sea-to-air flux, calculated using a parameterization that takes into account the attenuating effect of surfactants on gas exchange, is in the same range as the diapycnal flux. This indicates that common parameterizations for the gas transfer velocity might overestimate the air-sea gas exchange within highly productive upwelling zones.

  10. The Icarus Illusion: Technology, Doctrine and the Soviet Air Force.

    Science.gov (United States)

    1986-09-01

    have .𔃻 assumed command of the Western TV, which would explain Georgi Romanov’s comment in Helsinki 13 October 1984 that "Marshal Ogarkov commands the...Postgraduate School Monterey, California 93943 18. Dr. Howard Weinberg .. aval Center for International Science and Technology Naval Postgraduate

  11. Surface-catalyzed air oxidation reactions of hydrazines: Tubular reactor studies

    Science.gov (United States)

    Kilduff, Jan E.; Davis, Dennis D.; Koontz, Steven L.

    1988-01-01

    The surface-catalyzed air oxidation reactions of hydrazine, monomethylhydrazine, unsymmetrical dimethylhydrazine, symmetrical dimethylhydrazine, trimethylhydrazine and tetramethylhydrazine were investigated in a metal-powder packed turbular flow reactor at 55 plus or minus 3 C. Hydrazine was completely reacted on all surfaces studied. The major products of monomethylhydrazine (MMH) oxidation were methanol, methane and methyldiazene. The di-, tri- and tetra-methyl hydrazines were essentially unreactive under these conditions. The relative catalytic reactivities toward MMH are: Fe greater than Al2O3 greater than Ti greater than Zn greater than 316 SS greater than Cr greater than Ni greater than Al greater than 304L SS. A kinetic scheme and mechanism involving adsorption, oxidative dehydrogenation and reductive elimination reactions on a metal oxide surface are proposed.

  12. Study on dynamics characteristics of wet air oxidation of non-ionic surfactants

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Wet air oxidation is an effective method to deal with highly concentrated nondegradable emulsification wastewater which contains non-ionic surfactants. This article illustrates our investigation on dynamic characteristics of wet air oxidation of typical non-ionic surfactants like polyether, phenol ether and widely used alcohol ether. The experimental results indicated that the oxidation rate of polyether, phenol ether and alcohol ether obviously ascended as the temperature rose. A good oxidation effect was available at 240℃. The TOC removal rate could reach 88.0%, 94% and 91.5%, after 125 min reaction. Alcohol ether was prone to an easier oxidation compared with polyether and phenol ether when the temperature was 220℃ or below. The oxidation rate of alcohol ether was higher than that of polyether at 160℃, while the oxidation rate of polyether was higher than that of phenol ether between 180℃ and 220℃. During the later period of the reaction at 240℃, the rate of phenol ether was higher than that of alcohol ether, which was still higher than that of polyether. Partitioned first order kinetics model analy-sis showed that the apparent activation energy of alcohol ether was lower than that of both polyether and phenol ether in the leading stage and lagging stage, and it was easy to acquire a higher oxidation rate for alcohol ether at low temperature. Three parameter general dynamics model analyses showed that the reason why the oxidation rate of polyether was lower than that of alcohol ether was that the oxidation of polyether was more apt to be converted to intermediate production than that of alcohol ether, whereas between 200℃ and 220℃, the direct oxidation rate of polyether and the oxidation rate of intermediate product were obviously lower than that of alcohol ether. The apparent activation energy of direct and indirect oxidation of polyether was 43.37 and 60.45 kJ?mol?1, respectively, while the corre-sponding apparent activation energy of alcohol

  13. Study on dynamics characteristics of wet air oxidation of non-ionic surfactants

    Institute of Scientific and Technical Information of China (English)

    ZENG XinPing; TANG WenWei; ZHAO JianFu; GU GuoWei

    2008-01-01

    Wet air oxidation is an effective method to deal with highly concentrated nondegradable emulsification wastewater which contains non-ionic surfactants. This article illustrates our investigation on dynamic characteristics of wet air oxidation of typical non-ionic surfactants like polyether, phenol ether and widely used alcohol ether. The experimental results indicated that the oxidation rate of polyether, phenol ether and alcohol ether obviously ascended as the temperature rose. A good oxidation effect was available at 240℃. The TOC removal rate could reach 88.0%, 94% and 91.5%, after 125 min reaction. Alcohol ether was prone to an easier oxidation compared with polyether and phenol ether when the temperature was 220℃ or below. The oxidation rate of alcohol ether was higher than that of polyether at 160℃, while the oxidation rate of polyether was higher than that of phenol ether between 180℃ and 220℃. During the later period of the reaction at 240℃, the rate of phenol ether was higher than that of alcohol ether, which was still higher than that of polyether. Partitioned first order kinetics model analysis showed that the apparent activation energy of alcohol ether was lower than that of both polyether and phenol ether in the leading stage and lagging stage, and it was easy to acquire a higher oxidation rate for alcohol ether at low temperature. Three parameter general dynamics model analyses showed that the reason why the oxidation rate of polyether was lower than that of alcohol ether was that the oxidation of polyether was more apt to be converted to intermediate production than that of alcohol ether, whereas between 200℃ and 220℃, the direct oxidation rate of polyether and the oxidation rate of intermediate product were obviously lower than that of alcohol ether. The apparent activation energy of direct and indirect oxidation of polyether was 43.37 and 60.45 kJ·mol-1, respectively, while the corresponding apparent activation energy of alcohol

  14. Oxidation capacity of the city air of Santiago, Chile

    Directory of Open Access Journals (Sweden)

    Y. F. Elshorbany

    2009-03-01

    Full Text Available The oxidation capacity of the highly polluted urban area of Santiago, Chile has been evaluated during a summer measurement campaign carried out from 8–20 March 2005. The hydroxyl (OH radical budget was evaluated employing a simple quasi-photostationary-state model (PSS constrained with simultaneous measurements of HONO, HCHO, O3, NO, NO2, j(O1D, j(NO2, 13 alkenes and meteorological parameters. In addition, a zero dimensional photochemical box model based on the Master Chemical Mechanism (MCMv3.1 has been used to estimate production rates and total free radical budgets, including OH, HO2 and RO2. Besides the above parameters, the MCM model has been constrained by the measured CO and volatile organic compounds (VOCs including alkanes and aromatics. Both models simulate the same OH concentration during daytime indicating that the primary OH sources and sinks included in the simple PSS model predominate. Mixing ratios of the main OH radical precursors were found to be in the range 0.8–7 ppbv (HONO, 0.9–11 ppbv (HCHO and 0–125 ppbv (O3. The alkenes average mixing ratio was ~58 ppbC accounting for ~12% of the total identified non-methane hydrocarbons (NMHCs. During the daytime (08:00 h–19:00 h, HONO photolysis was shown to be the most important primary OH radical source comprising alone ~55% of the total initial production rate, followed by alkene ozonolysis (~24% and photolysis of HCHO (~16% and O3 (~5%. The calculated average and maximum daytime OH production rates from HONO photolysis was 1.7 ppbv h−1 and 3.1 ppbv h−1, respectively. Based on the experimental results a strong photochemical daytime source of HONO is proposed. A detailed analysis of the sources of OH radical precursors has also been carried out.

  15. Air Force Domestic Technology Transfer: Is It Effective

    Science.gov (United States)

    1992-04-01

    Solow , Robert M., and Thurow, Lester C., "Toward a New Industrial America," Scientific American, June 1989, Vol. 260, No. 6, p. 42. ’ National...pp. 1, 2. " Berger, Suzanne, Dertouzos, Michael L., Lester, Richard K., Solow , Robert M., and Thurow, Lester C., "Toward a New Industrial America...American industries, but the inability to bring " Inman, B.R., and Burton, Daniel F., Jr, "Technology and Competitiveness: The New Policy Frontier

  16. Air Force Research in Aero Propulsion Technology (AFRAPT)

    Science.gov (United States)

    1990-09-27

    Aero Propulsion Technology (AFRAPT) 12. PERSONAL AUTHOR(S) Profs. J. Dugundji , A. Epstein, M. Giles, E. Greitzer, M. Martinez-Sanchez, flr r T~ri 13a...Professor of Aeronautics and Astronautics Director, Gas Turbine Laboratory John Dugundji Professor, Dept. of Aeronautics and Astronautics Alan H. Epstein...Professor J. Dugundji /Professor E.M. Greitzer Project: Compressor Stabilization Through Structural Feedback Trainee: Dana Lindquist Advisor: Professor M.B

  17. Neuro-Linguistic Programming: Human Technology for Today’s Air Force.

    Science.gov (United States)

    1986-04-01

    Part III, pp. 4-5. ’ 26. Ibid, p. 6. 27. Donald W. McCormick, " Neurolinguistic Programming : A Resource Guide and Review of the Research, The 1984...Carol Johnson, " Neurolinguistic Programming --Mystique or Mistake?" Army Organizational Effectiveness Journal, No. 1, 1985, pp. 74-80. 29. Dilts...AD-RI67 836 NEURO-LINGUISTIC PROGRAMMING : HUHAN TECHNOLOGY FOR / TODAY’S AIR FORCEMU AIR COMMAND ANM STAFF COLL NAXHELL AFB AL J B CAULFIELD APR 86

  18. Leveraging Advanced Technology in Army and Air Force Readiness and Sustainment Training

    Science.gov (United States)

    2007-11-02

    USAWC STRATEGY RESEARCH PROJECT LEVERAGING ADVANCED TECHNOLOGY IN ARMY AND AIR FORCE READINESS AND SUSTAINMENT TRAINING by Kathy Lindsey Department...of Air Force Colonel Richard M. Meinhart Project Advisor The views expressed in this academic research paper are those of the author and do not...necessarily reflect the official policy or position of the U.S. Government, the Department of Defense, or any of its agencies. U.S. Army War College CARLISLE

  19. Field Measurements of Perceived Air Quality in the Test-Bed for Innovative Climate Conditioning Technologies

    DEFF Research Database (Denmark)

    Kolarik, Jakub; Toftum, Jørn; Kabrhel, Michal

    , relative humidity and CO2 concentration. Results showed that the mean sensory pollution load in the tested offices was 0.09±0.02 olf/m2 (mean±SEM). This refers to a low-polluting building according to CEN Report CR 1752. The acceptability of the air quality was worst in unoccupied offices ventilated at 20...... m3/h. Application of DCV decreased the CO2 concentration, but did not result in statistically significant improvement of the perceived air quality. It was not possible to quantify the influence on the sensory pollution load of particular technologies tested as part of the Clear-up. However......Field measurements of perceived air quality were conducted in an experimental test bed for innovative building technologies situated at the Czech Technical University in Prague. The technologies included photocatalytically active paint, vacuum porous insulation and wall plaster containing phase...

  20. Air cleaning using regenerative silica gel wheel

    DEFF Research Database (Denmark)

    Fang, Lei

    2011-01-01

    This paper discussed the necessity of indoor air cleaning and the state of the art information on gas-phase air cleaning technology. The performance and problems of oxidation and sorption air cleaning technology were summarized and analysed based on the literature studies. Eventually, based on an...

  1. Air-pressure tunable depletion width, rectification behavior, and charge conduction in oxide nanotubes.

    Science.gov (United States)

    Alivov, Yahya; Funke, Hans H; Singh, Vivek; Nagpal, Prashant

    2015-02-01

    Metal-oxide nanotubes provide large surface areas and functionalizable surfaces for a variety of optical and electronic applications. Here we report air-tunable rectifying behavior, depletion width modulation, and two-dimensional (2D) charge conduction in hollow titanium-dioxide nanotubes. The metal contact forms a Schottky-diode in the nanotubes, and the rectification factor (on/off ratio) can be varied by more than 3 orders of magnitude (1-2 × 10(3)) as the air pressure is increased from 2 mTorr to atmospheric pressure. This behavior is explained using a change in depletion width of these thin nanotubes by adsorption of water vapor on both surfaces of a hollow nanotube, and the resulting formation of a metal-insulator-semiconductor (MIS) junction, which controls the 2D charge conduction properties in thin oxide nanotubes.

  2. Treatment of desizing wastewater from the textile industry by wet air oxidation

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper describes the application of wet air oxidation to the treatment of desizing wastewater from two textile companies. A two-liter high temperature, high pressure autoclave reactor was used in the study. The range of operating temperatures examined was between 150 and 290℃, and the partial pressure of oxygen ranged from 0. 375 to 2.25 MPa. Variations in pH,CODCr and TOD content were monitored during each experiment and used to assess the extent of conversion of the process. The effects of temperature, pressure and reaction time were explored extensively. More than 90 % CODCr reduction and 80 % TOC removal have been obtained. The results have also been demonstrated that WAO is a suitable pre-treatment methods due to improvement of the BOD5/CODCr ratio of desizing wastewater. The reaction kinetics of wet air oxidation of desizing wastewater has been proved to be two steps, a fast reaction followed by a slow reaction stage.

  3. Effect of Composition and Mass Ratio on the Catalytic Wet Air Oxidation Catalyst Cu–Fe–La/FSC

    Directory of Open Access Journals (Sweden)

    Wu Chao

    2016-01-01

    Full Text Available The catalytic wet air oxidation (CWAO technology is used for the treatment of the simulated printing and dyeing wastewater and also for investigating the catalyst performance indicators such as catalyst activity and stability. The catalyst activity is mainly reflected from the water decolorization and CODCr removal rates, and the stability of the catalyst is mainly reflected by the quantity of metal dissolution. The experimental results showed that the prepared Cu–Fe–La/FSC catalyst with a 1:1:2 ratio of Cu–Fe–La by the impregnation method exhibited good activity for the treatment of the simulated printing and dyeing wastewater by the CWAO method, and the decolorization and CODCr removal rates using this catalyst were 98.7% and 78.6%, respectively, with a higher catalytic activity, lower concentration of metal dissolution, and good stability.

  4. Zircaloy-4 and M5 high temperature oxidation and nitriding in air

    Energy Technology Data Exchange (ETDEWEB)

    Duriez, C. [Institut de Radioprotection et Surete Nucleaire, Direction de Prevention des Accidents Majeurs, Centre de Cadarache, 13115 St Paul Lez Durance (France)], E-mail: christian.duriez@irsn.fr; Dupont, T.; Schmet, B.; Enoch, F. [Universite Technologique de Troyes, BP 2060, 10010 Troyes (France)

    2008-10-15

    For the purpose of nuclear power plant severe accident analysis, degradation of Zircaloy-4 and M5 cladding tubes in air at high temperature was investigated by thermo-gravimetric analysis, in isothermal conditions, in a 600-1200 deg. C temperature range. Alloys were investigated either in a 'as received' bare state, or after steam pre-oxidation at 500 {sup o}C to simulate in-reactor corrosion. At the beginning of air exposure, the oxidation rate obeys a parabolic law, characteristic of solid-state diffusion limited regime. Parabolic rate constants compare, for Zircaloy-4 as well as for M5, with recently assessed correlations for high temperature Zircaloy-4 steam-oxidation. A thick layer of dense protective zirconia having a columnar structure forms during this diffusion-limited regime. Then, a kinetic transition (breakaway type) occurs, due to radial cracking along the columnar grain boundaries of this protective dense oxide scale. The breakaway is observed for a scale thickness that strongly increases with temperature. At the lowest temperatures, the M5 alloy appears to be breakaway-resistant, showing a delayed transition compared to Zircaloy-4. However, for both alloys, a pre-existing corrosion scale favours the transition, which occurs much earlier. The post transition kinetic regime is linear only for the lowest temperatures investigated. From 800 deg. C, a continuously accelerated regime is observed and is associated with formation of a strongly porous non-protective oxide. A mechanism of nitrogen-assisted oxide growth, involving formation and re-oxidation of ZrN particles, as well as nitrogen associated zirconia phase transformations, is proposed to be responsible for this accelerated degradation.

  5. Improvement to Air2Air Technology to Reduce Fresh-Water Evaporative Cooling Loss at Coal-Based Thermoelectric Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Ken Mortensen

    2011-12-31

    This program was undertaken to enhance the manufacturability, constructability, and cost of the Air2Air{TM} Water Conservation and Plume Abatement Cooling Tower, giving a validated cost basis and capability. Air2Air{TM} water conservation technology recovers a portion of the traditional cooling tower evaporate. The Condensing Module provides an air-to-air heat exchanger above the wet fill media, extracting the heat from the hot saturated moist air leaving in the cooling tower and condensing water. The rate of evaporate water recovery is typically 10% - 25% annually, depending on the cooling tower location (climate). This program improved the efficiency and cost of the Air2Air{TM} Water Conservation Cooling Tower capability, and led to the first commercial sale of the product, as described.

  6. Overview of air biofiltration - basic technology, economics and integration with other control technologies for effective treatment of air toxics

    Energy Technology Data Exchange (ETDEWEB)

    Govind, R. [Univ. of Cincinnati, OH (United States); Bishop, D.F. [Environmental Protection Agency, Cincinnati, OH (United States)

    1996-12-31

    This paper provides an overview of air biofiltration with experimental data on the performance of peat/compost, pelletized packed bed and structured media biofilters. It is shown that use of high surface area per unit volume structured media results in higher contaminant treatment rates per unit biofilter volume. Peat/compost biofilters exhibit lower removal efficiencies at high (> 100 ppmv) inlet contaminant concentrations and require control of media moisture content. Increase of temperature results in increasing biodegradation rates. It is shown that use of structured ceramic media allows effective control of biomass buildup by continuous removal of biomass from the biofilter media and that the biomass removal rate depends on nutrient flowrate. An experimental system is presented which enables biofilm kinetics to be determined and a simple biofilter model is developed in this paper. A group contribution approach has been developed to estimate biokinetic parameter which allows biofiltration effectiveness to be determined for a variety of volatile organic compounds (VOCs). Finally, a procedure is presented, illustrated by an example, which is used to develop an integrated process for effective treatment of air contaminants. 22 refs., 12 figs., 4 tabs.

  7. Amine-Oxide Hybrid Materials for CO2 Capture from Ambient Air.

    Science.gov (United States)

    Didas, Stephanie A; Choi, Sunho; Chaikittisilp, Watcharop; Jones, Christopher W

    2015-10-20

    Oxide supports functionalized with amine moieties have been used for decades as catalysts and chromatographic media. Owing to the recognized impact of atmospheric CO2 on global climate change, the study of the use of amine-oxide hybrid materials as CO2 sorbents has exploded in the past decade. While the majority of the work has concerned separation of CO2 from dilute mixtures such as flue gas from coal-fired power plants, it has been recognized by us and others that such supported amine materials are also perhaps uniquely suited to extract CO2 from ultradilute gas mixtures, such as ambient air. As unique, low temperature chemisorbents, they can operate under ambient conditions, spontaneously extracting CO2 from ambient air, while being regenerated under mild conditions using heat or the combination of heat and vacuum. This Account describes the evolution of our activities on the design of amine-functionalized silica materials for catalysis to the design, characterization, and utilization of these materials in CO2 separations. New materials developed in our laboratory, such as hyperbranched aminosilica materials, and previously known amine-oxide hybrid compositions, have been extensively studied for CO2 extraction from simulated ambient air (400 ppm of CO2). The role of amine type and structure (molecular, polymeric), support type and structure, the stability of the various compositions under simulated operating conditions, and the nature of the adsorbed CO2 have been investigated in detail. The requirements for an effective, practical air capture process have been outlined and the ability of amine-oxide hybrid materials to meet these needs has been discussed. Ultimately, the practicality of such a "direct air capture" process is predicated not only on the physicochemical properties of the sorbent, but also how the sorbent operates in a practical process that offers a scalable gas-solid contacting strategy. In this regard, the utility of low pressure drop monolith

  8. Air, aqueous and thermal stabilities of Ce3+ ions in cerium oxide nanoparticle layers with substrates

    KAUST Repository

    Naganuma, Tamaki

    2014-01-01

    Abundant oxygen vacancies coexisting with Ce3+ ions in fluorite cerium oxide nanoparticles (CNPs) have the potential to enhance catalytic ability, but the ratio of unstable Ce3+ ions in CNPs is typically low. Our recent work, however, demonstrated that the abundant Ce3+ ions created in cerium oxide nanoparticle layers (CNPLs) by Ar ion irradiation were stable in air at room temperature. Ce valence states in CNPs correlate with the catalytic ability that involves redox reactions between Ce3+ and Ce4+ ions in given application environments (e.g. high temperature in carbon monoxide gas conversion and immersion conditions in biomedical applications). To better understand the mechanism by which Ce3+ ions achieve stability in CNPLs, we examined (i) extra-long air-stability, (ii) thermal stability up to 500 °C, and (iii) aqueous stability of Ce 3+ ions in water, buffer solution and cell culture medium. It is noteworthy that air-stability of Ce3+ ions in CNPLs persisted for more than 1 year. Thermal stability results showed that oxidation of Ce 3+ to Ce4+ occurred at 350 °C in air. Highly concentrated Ce3+ ions in ultra-thin CNPLs slowly oxidized in water within 1 day, but stability was improved in the cell culture medium. Ce 3+ stability of CNPLs immersed in the medium was associated with phosphorus adsorption on the Ce3+ sites. This study also illuminates the potential interaction mechanisms of stable Ce3+ ions in CNPLs. These findings could be utilized to understand catalytic mechanisms of CNPs with abundant oxygen vacancies in their application environments. © The Royal Society of Chemistry 2014.

  9. Methods for air cleaning and protection of building occupants from airborne pathogens

    DEFF Research Database (Denmark)

    Bolashikov, Zhecho Dimitrov; Melikov, Arsen Krikor

    2009-01-01

    germicidal irradiation (UVGI), photocatalytic oxidation (PCO), plasmacluster ions and other technologies for air disinfection and purification from pathogens are analyzed with respect to currently used air distribution principles. The importance of indoor air characteristics, such as temperature, relative...

  10. Secondary organic aerosol formation from photo-oxidation of toluene with NOx and SO2: Chamber simulation with purified air versus urban ambient air as matrix

    Science.gov (United States)

    Deng, Wei; Liu, Tengyu; Zhang, Yanli; Situ, Shuping; Hu, Qihou; He, Quanfu; Zhang, Zhou; Lü, Sujun; Bi, Xinhui; Wang, Xuemei; Boreave, Antoinette; George, Christian; Ding, Xiang; Wang, Xinming

    2017-02-01

    Chamber studies on the formation of secondary aerosols are mostly performed with purified air as matrix, it is of wide concern in what extent they might be different from the situations in ambient air, where a variety of gaseous and particulate components preexist. Here we compared the photo-oxidation of "toluene + NOx + SO2" combinations in a smog chamber in real urban ambient air matrix with that in purified air matrix. The secondary organic aerosols (SOA) mass concentrations and yields from toluene in the ambient air matrix, after subtracted ambient air background primary and secondary organic aerosols, were 9.0-34.0 and 5.6-12.9 times, respectively, greater than those in purified air matrix. Both homogeneous and heterogeneous oxidation of SO2 were enhanced in ambient air matrix experiments with observed 2.0-7.5 times higher SO2 degradation rates and 2.6-6.8 times faster sulfate formation than that in purified air matrix, resulting in higher in-situ particle acidity and consequently promoting acid-catalyzed SOA formation. In the ambient air experiments although averaged OH radical levels were elevated probably due to heterogeneous formation of OH on particle surface and/or ozonolysis of alkenes, non-OH oxidation pathways of SO2 became even more dominating. Under the same organic aerosol mass concentration, the SOA yields of toluene in purified air matrix experiments matched very well with the two-product model curve by Ng et al. (2007), yet the yields in ambient air on average was over two times larger. The results however were much near the best fit curve by Hildebrandt et al. (2009) with the volatility basis set (VBS) approach.

  11. Oxidation Analyses of Massive Air Ingress Accident of HTR-PM

    Directory of Open Access Journals (Sweden)

    Wei Xu

    2016-01-01

    Full Text Available The double-ended guillotine break (DEGB of the horizontal coaxial gas duct accident is a serious air ingress accident of the high temperature gas-cooled reactor pebble-bed module (HTR-PM. Because the graphite is widely used as the structure material and the fuel element matrix of HTR-PM, the oxidation analyses of this severe air ingress accident have got enough attention in the safety analyses of the HTR-PM. The DEGB of the horizontal coaxial gas duct accident is calculated by using the TINTE code in this paper. The results show that the maximum local oxidation of the matrix graphite of spherical fuel elements in the core will firstly reach 3.75⁎104 mol/m3 at about 120 h, which means that only the outer 5 mm fuel-free zone of matrix graphite will be oxidized out. Even at 150 h, the maximum local weight loss ratio of the nuclear grade graphite in the bottom reflectors is only 0.26. Besides, there is enough time to carry out some countermeasures to stop the air ingress during several days. Therefore, the nuclear grade graphite of the bottom reflectors will not be fractured in the DEGB of the horizontal coaxial gas duct accident and the integrity of the HTR-PM can be guaranteed.

  12. The degradation of Isophorone by catalytic wet air oxidation on Ru/TiZrO4.

    Science.gov (United States)

    Wei, Huangzhao; Yan, Xiaomiao; Li, Xianru; He, Songbo; Sun, Chenglin

    2013-01-15

    The catalyst Ru/TiZrO(4) was applied in the degradation of Isophorone by catalytic wet air oxidation. Mathematical models for the effects of reaction conditions on the Isophorone degradation by catalytic wet air oxidation were developed using a response surface methodology. A model was obtained for each response with multiple regression analysis and then was refined. Analysis of variance revealed that the models developed were adequate. The validity of the models was also verified by experimental data. Analysis of response surface showed that total organic carbon removal and Isophorone conversion were significantly affected (P≤0.01) by reaction time, temperature and their interactions, and affected (P≤0.05) by the square of reaction time. The point of zero charge of Ru/TiZrO(4) catalyst was about 1.72. The total organic carbon removal and Isophorone conversion had a great association with the zeta potential of Ru/TiZrO(4) catalyst. Finally, the degradation pathway of Isophorone in catalytic wet air oxidation was proposed. Within 410 h, the total organic carbon removal remained above 95%, indicating that the Ru/TiZrO(4) catalyst had a good stability.

  13. CO2 Capture from the Air: Technology Assessment and Implications for Climate Policy

    Science.gov (United States)

    Keith, D. W.

    2002-05-01

    It is physically possible to capture CO2 directly from the air and immobilize it in geological structures. Today, there are no large-scale technologies that achieve air capture at reasonable cost. Yet, strong arguments suggest that it will comparatively easy to develop practical air capture technologies on the timescales relevant to climate policy [1]. This paper first analyzes the cost of air capture and then assesses the implications for climate policy. We first analyze the lower bound on the cost needed for air capture, describing the thermodynamic and physical limits to the use of energy and land. We then compare the costs of air capture to the cost of capture from combustion exhaust streams. While the intrinsic minimum energy requirement is larger for air capture, we argue that air capture has important structural advantages, such as the reduction of transport costs and the larger potential for economies of scale. These advantages suggest that, in the long-run air capture be competitive with other methods of achieving deep emissions reductions. We provide a preliminary engineering-economic analysis of an air capture system based on CaO to CaCO3 chemical looping [1]. We analyze the possibility of doing the calcination in a modified pressurized fluidized bed combustor (PFBC) burning coal in a CO2 rich atmosphere with oxygen supplied by an air separation unit. The CaCO3-to-coal ratio would be ~2:1 and the system would be nearly thermally neutral. PFBC systems have been demonstrated at capacities of over 100 MW. Such systems already include CaCO3 injection for sulfur control, and operate at suitable temperatures and pressures for calcination. We assess the potential to recover heat from the dissolution of CaO in order to reduce the overall energy requirements. We analyze the possibility of adapting existing large water/air heat exchangers for use as contacting systems to capture CO2 from the air using the calcium hydroxide solution. The implications of air capture

  14. Impact of clay mineral on air oxidation of PAH-contaminated soils.

    Science.gov (United States)

    Biache, Coralie; Kouadio, Olivier; Lorgeoux, Catherine; Faure, Pierre

    2014-09-01

    This work investigated the impact of a clay mineral (bentonite) on the air oxidation of the solvent extractable organic matters (EOMs) and the PAHs from contaminated soils. EOMs were isolated from two coking plant soils and mixed with silica sand or bentonite. These samples, as well as raw soils and bentonite/soil mixtures, were oxidized in air at 60 and 100 °C for 160 days. Mineralization was followed by measuring the CO2 produced over the experiments. EOM, polycyclic aromatic compound (PAC), including PAH, contents were also determined. Oxidation led to a decrease in EOM contents and PAH concentrations, these diminutions were enhanced by the presence of bentonite. Transfer of carbon from EOM to insoluble organic matter pointed out a condensation phenomenon leading to a stabilization of the contamination. Higher mineralization rates, observed during the oxidation of the soil/bentonite mixtures, seem to indicate that this clay mineral had a positive influence on the transformation of PAC into CO2.

  15. Pretreatment of Afyon alcaloide factory's wastewater by wet air oxidation (WAO).

    Science.gov (United States)

    Kaçar, Y; Alpay, E; Ceylan, V K

    2003-03-01

    In this study, pretreatment of Afyon (Turkey) alcaloide factory wastewater, a typical high strength industrial wastewater (chemical oxygen demand (COD)=26.65 kgm(-3), biological oxygen demand (BOD(5))=3.95 kgm(-3)), was carried out by wet air oxidation process. The process was performed in a 0.75 litre specially designed bubble reactor. Experiments were conducted to see the advantages of one-stage and two-stage oxidation and the effects of pressure, pH, temperature, catalyst type, catalyst loading and air or oxygen as gas source on the oxidation of the wastewater. In addition, BOD(5)/COD ratios of the effluents, which are generally regarded as an important index of biodegradability of a high-strength industrial wastewater, were determined at the end of some runs. After a 2h oxidation (T=150 degrees C, P=0.65 MPa, airflowrate=1.57 x 10(-5)m(3)s(-1), pH=7.0), the BOD(5)/COD ratio was increased from 0.15 to above 0.5 by using the salts of metals such as Co(2+),Fe(2+),Fe(2+)+Ni(2+),Cu(2+)+Mn(2+) as catalyst.

  16. In situ secondary organic aerosol formation from ambient pine forest air using an oxidation flow reactor

    Directory of Open Access Journals (Sweden)

    B. B. Palm

    2015-11-01

    Full Text Available Ambient air was oxidized by OH radicals in an oxidation flow reactor (OFR located in a montane pine forest during the BEACHON-RoMBAS campaign to study biogenic secondary organic aerosol (SOA formation and aging. High OH concentrations and short residence times allowed for semi-continuous cycling through a large range of OH exposures ranging from hours to weeks of equivalent (eq. atmospheric aging. A simple model is derived and used to account for the relative time scales of condensation of low volatility organic compounds (LVOCs onto particles, condensational loss to the walls, and further reaction to produce volatile, non-condensing fragmentation products. More SOA production was observed in the OFR at nighttime (average 4 μg m-3 when LVOC fate corrected compared to daytime (average 1 μg m-3 when LVOC fate corrected, with maximum formation observed at 0.4–1.5 eq. days of photochemical aging. SOA formation followed a similar diurnal pattern to monoterpenes, sesquiterpenes, and toluene + p-cymene concentrations, including a substantial increase just after sunrise at 07:00 LT. Higher photochemical aging (> 10 eq. days led to a decrease in new SOA formation and a loss of preexisting OA due to heterogeneous oxidation followed by fragmentation and volatilization. When comparing two different commonly used methods of OH production in OFRs (OFR185 and OFR254, similar amounts of SOA formation were observed. We recommend the OFR185 mode for future forest studies. Concurrent gas-phase measurements of air after OH oxidation illustrate the decay of primary VOCs, production of small oxidized organic compounds, and net production at lower ages followed by net consumption of terpenoid oxidation products as photochemical age increased. New particle formation was observed in the reactor after oxidation, especially during times when precursor gas concentrations and SOA formation were largest. Approximately 6 times more SOA was formed in the reactor from OH

  17. Carbon catalysis in the aqueous oxidation of SO2 by NO2 and air

    Science.gov (United States)

    Schryer, D. R.; Schryer, J.; Cofer, W. R., III; Vay, S. A.

    1984-01-01

    Sulfur dioxide and an oxidant gas (air or NO2) were bubbled through aqueous suspensions of both washed and unwashed carbon black as well as through samples of wash water, which contained whatever soluble species were originally present on the carbon, and high-purity water. The sulfate yields obtained showed the washed and unwashed carbon to be equally catalytic for the oxidation of SO2 to sulfate by both oxidants, whereas little sulfate was generated in either the wash water or high-purity water in the absence of carbon. These results indicate that the sulfate yields produced in aqueous suspensions of the carbon studied are due to catalysis by the carbon particles rather than by soluble species dissolved from them.

  18. Cast Stone Oxidation Front Evaluation: Preliminary Results For Samples Exposed To Moist Air

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. A.; Almond, P. M.

    2013-11-26

    The rate of oxidation is important to the long-term performance of reducing salt waste forms because the solubility of some contaminants, e.g., technetium, is a function of oxidation state. TcO{sub 4}{sup -} in the salt solution is reduced to Tc(IV) and has been shown to react with ingredients in the waste form to precipitate low solubility sulfide and/or oxide phases. Upon exposure to oxygen, the compounds containing Tc(IV) oxidize to the pertechnetate ion, Tc(VII)O{sub 4}{sup -}, which is very soluble. Consequently the rate of technetium oxidation front advancement into a monolith and the technetium leaching profile as a function of depth from an exposed surface are important to waste form performance and ground water concentration predictions. An approach for measuring contaminant oxidation rate (effective contaminant specific oxidation rate) based on leaching of select contaminants of concern is described in this report. In addition, the relationship between reduction capacity and contaminant oxidation is addressed. Chromate (Cr(VI) was used as a non-radioactive surrogate for pertechnetate, Tc(VII), in Cast Stone samples prepared with 5 M Simulant. Cast Stone spiked with pertechnetate was also prepared and tested. Depth discrete subsamples spiked with Cr were cut from Cast Stone exposed to Savannah River Site (SRS) outdoor ambient temperature fluctuations and moist air. Depth discrete subsamples spiked with Tc-99 were cut from Cast Stone exposed to laboratory ambient temperature fluctuations and moist air. Similar conditions are expected to be encountered in the Cast Stone curing container. The leachability of Cr and Tc-99 and the reduction capacities, measured by the Angus-Glasser method, were determined for each subsample as a function of depth from the exposed surface. The results obtained to date were focused on continued method development and are preliminary and apply to the sample composition and curing / exposure conditions described in this report. The

  19. Application of Boron Oxide as a Protective Surface Treatment to Decrease the Air Reactivity of Carbon Anodes

    Directory of Open Access Journals (Sweden)

    Ramzi Ishak

    2017-03-01

    Full Text Available The oxidation of a carbon anode with air and CO2 occurs during the electrolysis of alumina in Hall-Héroult cells, resulting in a significant overconsumption of carbon and dusting. Boron is well known to decrease the rate of this reaction for graphite. In this work, the application of boron oxide has been investigated to evaluate its inhibition effect on the air oxidation reaction, and to provide an effective protection for anodes. Different methods of impregnation coating have been explored. Impregnated anode samples were gasified under air at 525 °C according to the standard measurement methods. X-ray tomography was used to obtain the microstructural information of the samples before and after air-burning tests. The impregnated samples showed a very low oxidation reaction rate and dust generation.

  20. International Diffusion of Open Path FTIR Technology and Air Monitoring Methods: Taiwan (Republic of China).

    Science.gov (United States)

    Giese-Bogdan, Stefan It; Levine, Steven P

    1996-08-01

    International cooperation and diffusion of environmental technologies is a central goal of the U.S. EPA Environmental Technology Initiative, and is of great interest to many countries. One objective is to exchange knowledge and skills concerning new monitoring technologies. In this case, the technology was open path Fourier Transform Infrared Spectrometry (op-FTIR). Taiwan is a high-technology, newly industrialized country. Because of air pollution problems, it is interested in obtaining skills, knowledge, and instrumentation for monitoring air pollutants. In April 1994, the Industrial Technology Research Institute, Center for Industrial Safety and Health Technology (ITRI/CISH) in Hsinchu, Taiwan, requested intensive training in op-FTIR. Training was held between September 30,1994 and October 29,1994. During the stay, the instructor provided intensive training on op-FTIR theory as well as an introduction to available instrumentation and software. The training concluded with a field demonstration of the instrumentation in a manufacturing facility. This report gives an overview of the training methods, structure, and materials in the op-FTIR training course. It will also address various problems encountered while teaching this course. In addition, the potential use for this technology in industry as well as by the Taiwanese government will be explained.

  1. Production of Beauveria bassiana Air Conidia by Means of Optimization of Biphasic System Technology

    Directory of Open Access Journals (Sweden)

    Vladimir Gouli

    2014-08-01

    Full Text Available Air conidia production of Beauveria bassiana, strain CA-603 was studied based on modified diphasic system. The biomass yield obtained in the first phase based on submerged cultivation of fungus was processed using methodology providing different contact with air space. Our study indicated that productivity of the second stage of diphasic system is had inversely proportional dependence on depth of liquid fungal biomass. Increase of biomass depth is significantly decreased production of air conidia. Two methodology of biomass processing extending contact biomass with air space including distribution of fungal material on surface of hygroscopic paper and starch packaging peanuts were investigated. The novel substrates provided optimal contact between the submerged fungal biomass and the air, and overall, conidial production was directly proportional to the total area of air-to-fungal surface. Technologies based on the starch peanuts and hygroscopic paper were the most productive in comparison to the common technology where the submerged culture was transferred to flat containers. The advantages and disadvantages of these different production methods are discussed.

  2. Evaluating the Air Quality, Climate Change, and Economic Impacts of Biogas Management Technologies

    Science.gov (United States)

    This is an abstract for a presentation that describes a project to evaluate economic and environmental performance of several biogas management technologies. It will analyze various criteria air pollutants, greenhouse gas emissions, and costs associated with the use of biogas. Th...

  3. 75 FR 15655 - Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air...

    Science.gov (United States)

    2010-03-30

    ... AGENCY 40 CFR Part 63 RIN 2060-AP91 Requirements for Control Technology Determinations for Major Sources... Division, Office of Air Quality Planning and Standards (D205- 02), Environmental Protection Agency... facilities. Brick and Structural Clay Products; Clay 327122 Ceramic wall and floor tile manufacturing...

  4. Evaluating the Air Quality, Climate Change, and Economic Impacts of Biogas Management Technologies

    Science.gov (United States)

    This is an abstract for a presentation that describes a project to evaluate economic and environmental performance of several biogas management technologies. It will analyze various criteria air pollutants, greenhouse gas emissions, and costs associated with the use of biogas. Th...

  5. Raman spectroscopy analysis of air grown oxide scale developed on pure zirconium substrate

    Energy Technology Data Exchange (ETDEWEB)

    Kurpaska, L., E-mail: lukasz.kurpaska@ncbj.gov.pl [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France); National Center for Nuclear Research, St. A. Soltana 7/23, 05-400 Otwock-Swierk (Poland); Favergeon, J. [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France); Lahoche, L. [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France); Laboratoire des Technologies Innovantes, Université de Picardie Jules-Verne, EA 3899, Avenue des Facultés – Le Bailly, 80025 Amiens Cedex (France); El-Marssi, M. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules-Verne, 33 rue St. Leu, 80039 Amiens Cedex (France); Grosseau Poussard, J.-L. [LaSIE UMR-CNRS 7356, Pole Sciences et Technologie, Universite de La Rochelle, av. M Crepeau, 17042 La Rochelle, Cedex (France); Moulin, G.; Roelandt, J.-M. [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France)

    2015-11-15

    Using Raman spectroscopy technique, external and internal parts of zirconia oxide films developed at 500 °C and 600 °C on pure zirconium substrate under air at normal atmospheric pressure have been examined. Comparison of Raman peak positions of tetragonal and monoclinic zirconia phases, recorded during the oxide growth at elevated temperature, and after cooling at room temperature have been presented. Subsequently, Raman peak positions (or shifts) were interpreted in relation with the stress evolution in the growing zirconia scale, especially closed to the metal/oxide interface, where the influence of compressive stress in the oxide is the biggest. Reported results, for the first time show the presence of a continuous layer of tetragonal zirconia phase developed in the proximity of pure zirconium substrate. Based on the Raman peak positions we prove that this tetragonal layer is stabilized by the high compressive stress and sub-stoichiometry level. Presence of the tetragonal phase located in the outer part of the scale have been confirmed, yet its Raman characteristics suggest a stress-free tetragonal phase, therefore different type of stabilization mechanism. Presented study suggest that its stabilization could be related to the lattice defects introduced by highstoichiometry of zirconia or presence of heterovalent cations. - Highlights: • The oxide layer consists of a mixture of tetragonal and monoclinic phases, clearly distinguishable by Raman spectroscopy. • The layer located close to the metal/oxide interphase consists mainly of the tetragonal phase. • Small amount of tetragonal layer located in the external oxide scale have been observed. • Stabilization mechanism of the tetragonal phase located in the external part of the oxide have been proposed.

  6. Technologies for air quality monitoring; Tecnologias para el monitoreo de calidad del aire

    Energy Technology Data Exchange (ETDEWEB)

    Muriel, Manuel [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1996-12-31

    There are various measuring principles and systems whose usage is delimited by the type of contaminant to be measured. The author of this paper presents a revision of the different applications, measuring principles, systems, costs and selection of the equipment utilized for the measuring and monitoring the atmospheric emissions. The case of the pollutants emitted to the air by the Power Plants in analyzed [Espanol] Existen diversos principios y sistemas de medicion cuyo uso estara delimitado por el tipo de contaminante a medir. El autor de esta ponencia presenta una revision de las diferentes aplicaciones, principios de medicion, sistemas, costos y seleccion de los equipos utilizados en la medicion y monitoreo de emisiones atmosfericas. Se analiza el caso de los contaminantes emitidos a la atmosfera en las centrales termoelectricas

  7. Soil-based filtration technology for air purification: potentials for environmental and space life support application

    Science.gov (United States)

    Nelson, Mark; Bohn, Hinrich

    Soil biofiltration, also known as Soil bed reactor (SBR), technology was originally developed in Germany to take advantage of the diversity in microbial mechanisms to control gases producing malodor in industrial processes. The approach has since gained wider international acceptance and seen numerous improvements, for example, by the use of high-organic compost beds to maximize microbial processes. This paper reviews the basic mechanisms which underlay soil processes involved in air purification, advantages and limitations of the technology and the cur-rent research status of the approach. Soil biofiltration has lower capital and operating/energetic costs than conventional technologies and is well adapted to handle contaminants in moderate concentrations. The systems can be engineered to optimize efficiency though manipulation of temperature, pH, moisture content, soil organic matter and airflow rates. SBR technology was modified for application in the Biosphere 2 project, which demonstrated in preparatory research with a number of closed system testbeds that soil could also support crop plants while also serving as soil filters with air pumps to push air through the soil. This Biosphere 2 research demonstrated in several closed system testbeds that a number of important trace gases could be kept under control and led to the engineering of the entire agricultural soil of Biosphere 2 to serve as a soil filtration unit for the facility. Soil biofiltration, coupled with food crop produc-tion, as a component of bioregenerative space life support systems has the advantages of lower energy use and avoidance of the consumables required for other air purification approaches. Expanding use of soil biofiltration can aid a number of environmental applications, from the mitigation of indoor air pollution, improvement of industrial air emissions and prevention of accidental release of toxic gases.

  8. OXIDATION OF INCONEL 718 IN AIR AT TEMPERATURES FROM 973K TO 1620K.

    Energy Technology Data Exchange (ETDEWEB)

    GREENE,G.A.; FINFROCK,C.C.

    2000-10-01

    As part of the APT project, it was necessary to quantify the release of tungsten from the APT spallation target during postulated accident conditions in order to develop accident source terms for accident consequence characterization. Experiments with tungsten rods at high temperatures in a flowing steam environment characteristic of postulated accidents revealed that considerable vaporization of the tungsten occurred as a result of reactions with the steam and that the aerosols which formed were readily transported away from the tungsten surfaces, thus exposing fresh tungsten to react with more steam. The resulting tungsten release fractions and source terms were undesirable and it was decided to clad the tungsten target with Inconel 718 in order to protect it from contact with steam during an accident and mitigate the accident source term and the consequences. As part of the material selection criteria, experiments were conducted with Inconel 718 at high temperatures to evaluate the rate of oxidation of the proposed clad material over as wide a temperature range as possible, as well as to determine the high-temperature failure limit of the material. Samples of Inconel 718 were inserted into a preheated furnace at temperatures ranging from 973 K to 1620 K and oxidized in air for varying periods of time. After oxidizing in air at a constant temperature for the prescribed time and then being allowed to cool, the samples would be reweighed to determine their weight gain due to the uptake of oxygen. From these weight gain measurements, it was possible to identify three regimes of oxidation for Inconel 718: a low-temperature regime in which the samples became passivated after the initial oxidation, an intermediate-temperature regime in which the rate of oxidation was limited by diffusion and exhibited a constant parabolic rate dependence, and a high-temperature regime in which material deformation and damage accompanied an accelerated oxidation rate above the parabolic

  9. Technology Transfer: A Qualitative Analysis of Air Force Office of Research and Technology Applications

    Science.gov (United States)

    2006-06-01

    branch. Two, attending Department of Defense Technology Transfer Integrated Planning Team workshops. Three, attending two Federal Laboratory...Question 12 What database tools do you use to Perform ORTA duties? The number one database tool used was the Defense Technology Transfer Information

  10. Generic aspects of the airborne spread of human pathogens indoors and emerging air decontamination technologies.

    Science.gov (United States)

    Ijaz, M Khalid; Zargar, Bahram; Wright, Kathryn E; Rubino, Joseph R; Sattar, Syed A

    2016-09-02

    Indoor air can be an important vehicle for a variety of human pathogens. This review provides examples of airborne transmission of infectious agents from experimental and field studies and discusses how airborne pathogens can contaminate other parts of the environment to give rise to secondary vehicles leading air-surface-air nexus with possible transmission to susceptible hosts. The following groups of human pathogens are covered because of their known or potential airborne spread: vegetative bacteria (staphylococci and legionellae), fungi (Aspergillus, Penicillium, and Cladosporium spp and Stachybotrys chartarum), enteric viruses (noro- and rotaviruses), respiratory viruses (influenza and coronaviruses), mycobacteria (tuberculous and nontuberculous), and bacterial spore formers (Clostridium difficile and Bacillus anthracis). An overview of methods for experimentally generating and recovering airborne human pathogens is included, along with a discussion of factors that influence microbial survival in indoor air. Available guidelines from the U.S. Environmental Protection Agency and other global regulatory bodies for the study of airborne pathogens are critically reviewed with particular reference to microbial surrogates that are recommended. Recent developments in experimental facilities to contaminate indoor air with microbial aerosols are presented, along with emerging technologies to decontaminate indoor air under field-relevant conditions. Furthermore, the role that air decontamination may play in reducing the contamination of environmental surfaces and its combined impact on interrupting the risk of pathogen spread in both domestic and institutional settings is discussed.

  11. The air oxidation behavior of lanthanum ion implanted zirconium at 500 deg. C

    CERN Document Server

    Peng, D Q; Chen, X W; Zhou, Q G

    2003-01-01

    The beneficial effect of lanthanum ion implantation on the oxidation behavior of zirconium at 500 deg. C has been studied. Zirconium specimens were implanted by lanthanum ions using a MEVVA source at energy of 40 keV with a fluence range from 1x10 sup 1 sup 6 to 1x10 sup 1 sup 7 ions/cm sup 2 at maximum temperature of 130 deg. C, The weight gain curves were measured after being oxidized in air at 500 deg. C for 100 min, which showed that a significant improvement was achieved in the oxidation behavior of zirconium ion implanted with lanthanum compared with that of the as-received zirconium. The valence of the oxides in the scale was analyzed by X-ray photoemission spectroscopy; and then the depth distributions of the elements in the surface of the samples were obtained by Auger electron spectroscopy. Glancing angle X-ray diffraction at 0.3 deg. incident angles was employed to examine the modification of its phase transformation because of the lanthanum ion implantation in the oxide films. It was obviously fou...

  12. Photochemical ozone and nitric oxide formation in air-nitrogen dioxide mixtures containing sulfur dioxide or chlorine

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, J.S.; Springer, G.S.; Stedman, D.H.

    1980-01-01

    The effects of sulfur dioxide and chlorine on ozone and nitric oxide concentrations in nitrogen dioxide-air mixtures were studied. The presence of 0-10 ppM SO/sub 2/ produced no change in the air mixture. Addition of 1-15 ppm chlorine increased the ozone concentration in the air mixture. A reaction model describing the interactions of chlorine and NO/sub 2/ is presented. (1 diagram, 6 graphs, 30 references, 3 tables)

  13. Catalytic and non-catalytic wet air oxidation of sodium dodecylbenzene sulfonate: kinetics and biodegradability enhancement.

    Science.gov (United States)

    Suárez-Ojeda, María Eugenia; Kim, Jungkwon; Carrera, Julián; Metcalfe, Ian S; Font, Josep

    2007-06-18

    Wet air oxidation (WAO) and catalytic wet air oxidation (CWAO) were investigated as suitable precursors for the biological treatment of industrial wastewater containing sodium dodecylbenzene sulfonate (DBS). Two hours WAO semi-batch experiments were conducted at 15 bar of oxygen partial pressure (P(O2)) and at 180, 200 and 220 degrees C. It was found that the highest temperature provides appreciable total organic carbon (TOC) and chemical oxygen demand (COD) abatement of about 42 and 47%, correspondingly. Based on the main identified intermediates (acetic acid and sulfobenzoic acid) a reaction pathway for DBS and a kinetic model in WAO were proposed. In the case of CWAO experiments, seventy-two hours tests were done in a fixed bed reactor in continuous trickle flow regime, using a commercial activated carbon (AC) as catalyst. The temperature and P(O2) were 140-160 degrees C and 2-9 bar, respectively. The influence of the operating conditions on the DBS oxidation, the occurrence of oxidative coupling reactions over the AC, and the catalytic activity (in terms of substrate removal) were established. The results show that the AC without any supported active metal behaves bi-functional as adsorbent and catalyst, giving TOC conversions up to 52% at 160 degrees C and 2 bar of P(O2), which were comparable to those obtained in WAO experiments. Respirometric tests were completed before and after CWAO and to the main intermediates identified through the WAO and CWAO oxidation route. Then, the readily biodegradable COD (COD(RB)) of the CWAO and WAO effluents were found. Taking into account these results it was possible to compare whether or not the CWAO or WAO effluents were suitable for a conventional activated sludge plant inoculated with non adapted culture.

  14. Impact of air pollution on oxidative DNA damage and lipid peroxidation in mothers and their newborns.

    Science.gov (United States)

    Ambroz, Antonin; Vlkova, Veronika; Rossner, Pavel; Rossnerova, Andrea; Svecova, Vlasta; Milcova, Alena; Pulkrabova, Jana; Hajslova, Jana; Veleminsky, Milos; Solansky, Ivo; Sram, Radim J

    2016-08-01

    Ambient air particulate matter (PM) represents a class of heterogeneous substances that form one component of air pollution. Oxidative stress has been implicated as an important action mechanism for PM on the human organism. Oxidative damage induced by reactive oxygen species (ROS) may affect any cellular macromolecule. The aim of our study was to investigate the impact of air pollution on oxidative DNA damage [8-oxo-7,8-dihydro-2'-deoxyguanosine (8-oxodG)] and lipid peroxidation [15-F2t-isoprostane (15-F2t-IsoP)] in the urine and blood from mothers and newborns from two localities with different levels of air pollution: Ceske Budejovice (CB), a locality with a clean air, and Karvina, a locality with high air pollution. The samples from normal deliveries (38-41 week+) of nonsmoking mothers and their newborns were collected in the summer and winter seasons. Higher PM2.5 concentrations were found in Karvina than in CB in the summer 2013 (mean±SD: 20.41±6.28 vs. 9.45±3.62μg/m(3), P<0.001), and in the winter 2014 (mean±SD: 53.67±19.76 vs. 27.96±12.34μg/m(3), P<0.001). We observed significant differences in 15-F2t-IsoP levels between the summer and winter seasons in Karvina for newborns (mean±SD: 64.24±26.75 vs. 104.26±38.18pg/ml plasma, respectively) (P<0.001). Levels of 8-oxodG differed only in the winter season between localities, they were significantly higher (P<0.001) in newborns from Karvina in comparison with CB (mean±SD: 5.70±2.94 vs. 4.23±1.51 nmol/mmol creatinine, respectively). The results of multivariate regression analysis in newborns from Karvina showed PM2.5 concentrations to be a significant predictor for 8-oxodG excretion, PM2.5 and B[a]P (benzo[a]pyrene) concentrations to be a significant predictor for 15-F2t-IsoP levels. The results of multivariate regression analysis in mothers showed PM2.5 concentrations to be a significant predictor of 8-oxodG levels.

  15. Slow Dynamics Model of Compressed Air Energy Storage and Battery Storage Technologies for Automatic Generation Control

    Energy Technology Data Exchange (ETDEWEB)

    Krishnan, Venkat; Das, Trishna

    2016-05-01

    Increasing variable generation penetration and the consequent increase in short-term variability makes energy storage technologies look attractive, especially in the ancillary market for providing frequency regulation services. This paper presents slow dynamics model for compressed air energy storage and battery storage technologies that can be used in automatic generation control studies to assess the system frequency response and quantify the benefits from storage technologies in providing regulation service. The paper also represents the slow dynamics model of the power system integrated with storage technologies in a complete state space form. The storage technologies have been integrated to the IEEE 24 bus system with single area, and a comparative study of various solution strategies including transmission enhancement and combustion turbine have been performed in terms of generation cycling and frequency response performance metrics.

  16. CONTACT: An Air Force technical report on military satellite control technology

    Science.gov (United States)

    Weakley, Christopher K.

    1993-07-01

    This technical report focuses on Military Satellite Control Technologies and their application to the Air Force Satellite Control Network (AFSCN). This report is a compilation of articles that provide an overview of the AFSCN and the Advanced Technology Program, and discusses relevant technical issues and developments applicable to the AFSCN. Among the topics covered are articles on Future Technology Projections; Future AFSCN Topologies; Modeling of the AFSCN; Wide Area Communications Technology Evolution; Automating AFSCN Resource Scheduling; Health & Status Monitoring at Remote Tracking Stations; Software Metrics and Tools for Measuring AFSCN Software Performance; Human-Computer Interface Working Group; Trusted Systems Workshop; and the University Technical Interaction Program. In addition, Key Technology Area points of contact are listed in the report.

  17. Isothermal oxidation behavior of Ti3Al-based alloy at 700-1 000 ℃ in air

    Institute of Scientific and Technical Information of China (English)

    QIAN Yu-hai; LI Mei-shuan; LU Bin

    2009-01-01

    The isothermal oxidation behavior of a Ti3Al-based alloy (Ti-24Al-14Nb-3V-0.5Mo-0.3Si, molar fraction, %) at 700- 1 000 ℃ in air was investigated. The oxidation kinetics of tested alloy approximately obeys the parabolic law, which shows that the oxidation process is dominated by the diffusion of ions. The oxidation diffusion activity energy is 241.32 kJ/mol. The tested alloy exhibits good oxidation resistance at 700 ℃. However, when the temperature is higher than 900 ℃, the oxidation resistance becomes poor. The XRD results reveal that the oxide product consists of a mixture of TiO2 and Al2O3. Serious crack and spallation of oxide scale occur during cooling procedure after being exposed at 1 000 ℃ in air for 16 h. According to the analysis of SEM/EDS and XRD, it is concluded that the Al2O3 oxide forms at the initially transient oxidation stage and most of it keeps in the outer oxide layer during the subsequent oxidation procedure.

  18. High-temperature oxidation behavior of Ti3AlC2 in air

    Institute of Scientific and Technical Information of China (English)

    XU Xue-wen; LI Yang-xian; ZHU Jiao-qun; MEI Bing-chu

    2006-01-01

    Not only the isothermal oxidation behaviors at 900-1 300 ℃ for 20 h in air of bulk Ti3AlC2 with 2.8% TiC which was sintered by hot pressing with the additive of silicon,but also the cyclic oxidation behavior at 1 100-1 300 °C for 30 cycles,were investigated by using TG,XRD,SEM. The isothermal and cyclic oxidation behaviors generally follow a parabolic rate law. The parabolic rate constants of the former increased from 1.39×10-10 kg2/(m4·s) at 900 ℃ to 5.56×10-9 kg2/(m4·s) at 1 300 ℃. The calculated activation energy is 136.45 kJ/mol. The oxidation products are á-Al2O3 and little TiO2 at 900-1 000 ℃,however when the temperature is raised up to 1 200 ℃,TiO2 partially reacts to Al2TiO5,and the reaction is completed at 1 300 ℃. This demonstrates that Ti3AlC2 has excellent oxidation resistance and good thermal shock because the dense continuous oxide scale consists of mass á-Al2O3 and little TiO2 and/or Al2TiO5. Generally,the oxide scale is grown by the inward diffusion of O2- and the outward diffusion of Ti4+ and Al3+.

  19. Identification of the Products of Oxidation of Quercetin by Air Oxygenat Ambient Temperature

    Directory of Open Access Journals (Sweden)

    Viktor A Utsal

    2007-03-01

    Full Text Available Oxidation of quercetin by air oxygen takes place in water and aqueous ethanol solutions under mild conditions, namely in moderately-basic media (pH ∼ 8-10 at ambient temperature and in the absence of any radical initiators, without enzymatic catalysis or irradiation of the reaction media by light. The principal reaction products are typical of other oxidative degradation processes of quercetin, namely 3,4-dihydroxy-benzoic (proto-catechuic and 2,4,6-trihydroxybenzoic (phloroglucinic acids, as well as the decarboxylation product of the latter – 1,3,5-trihydroxybenzene (phloroglucinol. In accordance with the literature data, this process involves the cleavage of the γ-pyrone fragment (ring C of the quercetin molecule by oxygen, with primary formation of 4,6-dihydroxy-2-(3,4-dihydroxybenzoyloxybenzoic acid (depside. However under such mild conditions the accepted mechanism of this reaction (oxidative decarbonylation with formation of carbon monoxide, CO should be reconsidered as preferably an oxidative decarboxylation with formation of carbon dioxide, CO2. Direct head-space analysis of the gaseous components formed during quercetin oxidation in aqueous solution at ambient temperature indicates that the ratio of carbon dioxide/carbon monoxide in the gas phase after acidification of the reaction media is ca. 96:4 %. Oxidation under these mild conditions is typical for other flavonols having OH groups at C3 (e.g., kaempferol, but it is completely suppressed if this hydroxyl group is substituted by a glycoside fragment (as in rutin, or a methyl substituent. An alternative oxidation mechanism involving the direct cleavage of the C2-C3 bond in the diketo-tautomer of quercetin is proposed.

  20. Conversion of the refractory ammonia and acetic acid in catalytic wet air oxidation of animal byproducts.

    Science.gov (United States)

    Fontanier, Virginie; Zalouk, Sofiane; Barbati, Stéphane

    2011-01-01

    Wet air oxidation (WAO) and catalytic wet air oxidation (CWAO) of slaughtered animal byproducts (ABPs) were investigated. Two step experiment was carried out consisting of a non-catalysed WAO run followed by a CWAO run at 170-275 degrees C, 20 MPa, and reaction time 180 min. The WAO (1st step) of sample (5 g/L total organic carbon (TOC)) yielded (82.0 +/- 4)% TOC removal and (78.4 +/- 13.2)% conversion of the initial organic-N into NH4(+)-N. Four metal catalysts (Pd, Pt, Rh, Ru) supported over alumina have been tested in catalytic WAO (2nd step) at elevated pH to enhance ammonia conversion and organic matter removal, particularly acetic acid. It was found that the catalysts Ru, Pt, and Rh had significant effects on the TOC removal (95.1%, 99.5% and 96.7%, respectively) and on the abatement of ammonia (93.4%, 96.7% and 96.3%, respectively) with high nitrogen selectivity. The catalyst Pd was found to have the less activity while Pt had the best performance. The X-Ray diffraction analysis showed that the support of catalyst was not stable under the experimental conditions since it reacted with phosphate present in solution. Nitrite and nitrate ions were monitored during the oxidation reaction and it was concluded that CWAO of ammonia in real waste treatment framework was in good agreement with the results obtained from the literature for ideal solutions of ammonia.

  1. Application of Catalytic Wet Air Oxidation to Treatment of Landfill Leachate on Co/Bi Catalyst

    Institute of Scientific and Technical Information of China (English)

    LI Hai-sheng; LIU Liang; ZHANG Rong; DONG De-ming; LIU Hong-liang; LI Yu

    2004-01-01

    Catalytic wet air oxidation(CWAO) was employed to reduce the organic compounds in landfill leachate and the effects of temperature, oxygen pressure, catalyst dosage, and concentration of the organic compounds on the TOC and CODCr removal rates were studied. The degradation kinetics of landfill leachate was also investigated and an exponential experiential model consisting of four influential factors was established to describe the reduction of the organic compounds in the landfill leachate. Meanwhile, the GC-MS technique was used to detect the components of the organic intermediates for the inference of the decomposition mechanisms of the organic compounds in landfill leachate. The results reveal that the reaction temperature and the catalyst dosage are the most important factors affecting the degradation reaction of the organic compounds and that the principal intermediates confirmed by GC-MS are organic acids at a percentage of more than 88% with no aldehydes or alcohols detected. The decomposition mechanisms of the organic compounds in landfill leachate were inferred based on the GC-MS information as follows: the activated gas phase O2 captured the hydrogen of the organic pollutants to produce free radicals, which then initiated the catalytic reaction. So most of the organic compounds were oxidized into CO2 and H2O ultimately. In general, catalytic wet air oxidation over catalyst Co3O4/Bi2O3 was a very promising technique for the treatment of landfill leachate.

  2. Sulfur Recovery from Acid Gas Using the Claus Process and High Temperature Air Combustion (HiTAC Technology

    Directory of Open Access Journals (Sweden)

    Mohamed Sassi

    2008-01-01

    Full Text Available Sulfur-bearing compounds are very detrimental to the environment and to industrial process equipment. They are often obtained or formed as a by-product of separation and thermal processing of fuels containing sulfur, such as coal, crude oil and natural gas. The two sulfur compounds, which need special attention, are: hydrogen sulfide (H2S and sulfur dioxide (SO2. H2S is a highly corrosive gas with a foul smell. SO2 is a toxic gas responsible for acid rain formation and equipment corrosion. Various methods of reducing pollutants containing sulfur are described in this paper, with a focus on the modified Claus process, enhanced by the use of High Temperature Air Combustion (HiTAC technology in the Claus furnace. The Claus process has been known and used in the industry for over 100 years. It involves thermal oxidation of hydrogen sulfide and its reaction with sulfur dioxide to form sulfur and water vapor. This process is equilibrium-limited and usually achieves efficiencies in the range of 94-97%, which have been regarded as acceptable in the past years. Nowadays strict air pollution regulations regarding hydrogen sulfide and sulfur dioxide emissions call for nearly 100% efficiency, which can only be achieved with process modifications. High temperature air combustion technology or otherwise called flameless (or colorless combustion is proposed here for application in Claus furnaces, especially those employing lean acid gas streams, which cannot be burned without the use of auxiliary fuel or oxygen enrichment under standard conditions. With the use of HiTAC it has been shown, however, that fuel-lean, Low Calorific Value (LCV fuels can be burned with very uniform thermal fields without the need for fuel enrichment or oxygen addition. The uniform temperature distribution favors clean and efficient burning with an additional advantage of significant reduction of NOx, CO and hydrocarbon emission.

  3. DEMONSTRATION BULLETIN: CAV-OX ULTRAVIOLET OXIDATION PROCESS MAGNUM WATER TECHNOLOGY

    Science.gov (United States)

    The CAV-OX® technology (see Fig- ure 1) destroys organic contaminants, including chlorinated hy- drocarbons, in water. The process uses hydrogen peroxide, hy- drodynamic cavitation, and ultraviolet (UV) radiation to photolyze and oxidize organic compounds present in water at ...

  4. DEMONSTRATION BULLETIN: CAV-OX ULTRAVIOLET OXIDATION PROCESS MAGNUM WATER TECHNOLOGY

    Science.gov (United States)

    The CAV-OX® technology (see Fig- ure 1) destroys organic contaminants, including chlorinated hy- drocarbons, in water. The process uses hydrogen peroxide, hy- drodynamic cavitation, and ultraviolet (UV) radiation to photolyze and oxidize organic compounds present in water at ...

  5. Technology for future low-pollution air-craft gas turbines. Technologie fuer kuenftige schadstoffarme Luftfahrtgasturbinen

    Energy Technology Data Exchange (ETDEWEB)

    Weyer, H.B. (Inst. fuer Antriebstechnik, Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany))

    1992-01-01

    The author highlights the state of the art and development of aviation and the resulting atmospheric pollution with a special reference to civilian air traffic at cruising altitude. The propagation and long-term chemical effect of power-unit exhaust gases are not discussed; these complex processes of diffusion and atmospheric chemistry are dealt with in papers of their own. The author focusses on future aviation technologies which will improve the pollutivity and profitability of air-craft while maintaining their high level of operational safety. (orig.)

  6. Fabrication technology of CNT-Nickel Oxide based planar pseudocapacitor for MEMS and NEMS

    Science.gov (United States)

    Lebedev, E. A.; Kitsyuk, E. P.; Gavrilin, I. M.; Gromov, D. G.; Gruzdev, N. E.; Gavrilov, S. A.; Dronov, A. A.; Pavlov, A. A.

    2015-11-01

    Fabrication technology of planar pseudocapacitor (PsC) based on carbon nanotube (CNT) forest, synthesized using plasma enhanced chemical vapor deposition (PECVD) method, covered with thin nickel oxide layer deposited by successive ionic layer adsorption and reaction (SILAR) method, is demonstrated. Dependences of deposited oxide layers thickness on device specific capacities is studied. It is shown that pseudocapacity of nickel oxide thin layer increases specific capacity of the CNT's based device up to 2.5 times.

  7. [Technology of nitrous oxide/oxygen inhalation sedation and its clinical application in pediatric dentistry].

    Science.gov (United States)

    Zhong, Tian; Hu, Daoyong

    2014-02-01

    Dental fear is a common problem in pediatric dentistry. Therefore, sedation for pediatric patients is an essential tool for anxiety management. Nitrous oxide/oxygen inhalation sedation is a safe, convenient, effective way to calm children. The review is about the technology of nitrous oxide/oxygen inhalation sedation and its clinical application in pediatric dentistry.

  8. Evolution of Anode Porosity under Air Oxidation: The Unveiling of the Active Pore Size

    Directory of Open Access Journals (Sweden)

    Francois Chevarin

    2017-03-01

    Full Text Available The carbon anode, used in aluminum electrolysis (Hall–Héroult process, is over-consumed by air oxidation and carboxy-reaction (with CO2. Several anode features may affect this over-consumption, such as impurity content, graphitization level and anode porosity features (e.g., porosity volume fraction or pore size distribution. The two first parameters are basically related to the quality of raw materials and coke calcination conditions. Anode porosity is, however, greatly affected by anode manufacturing conditions, and is possible to be modified, to some extent, by adjusting the anode recipe and the processing parameters. This work aims to investigate the effect of anode porosity on its air reactivity. Baked anode samples were prepared in laboratory scale and then crushed into powder form (−4760 + 4000 µm. The recipe for anode preparation was similar to a typical industrial recipe, except that in the lab scale no butt particles were used in the recipe. Anode particles were then gasified at six different conversion levels (0, 5, 15, 25, 35 and 50 wt % under air at 525 °C. The porosity was characterized in several pore size ranges, measured by nitrogen adsorption and mercury intrusion (0.0014–0.020, 0.002–0.025, 0.025–0.100, 0.1–40.0 and superior at 40 µm. The volume variation of each pore range, as a function of carbon conversion, was assessed and used to determine the size of the most active pores for air oxidation. The most active pore size was found to be the pores inferior at 40 µm before 15 wt % of gasification and pores superior at 40 µm between 15 and 50 wt % of carbon conversion. Limitation of pore size range could be used as an additional guideline, along with other targets such as high homogeneity and density, to set the optimum anode manufacturing parameters.

  9. Analysis of particles produced by oxidation of dilute xylene in air under electron beam irradiation

    Science.gov (United States)

    Hakoda, Teruyuki; Goto, Hitoshi; Shimada, Akihiko; Ochi, Masafumi; Kojima, Takuji

    2006-03-01

    The generator of electron beams with energies of 55 keV (max.) and currents of 0.50 mA (max.) was developed as an irradiation source for the analysis of particles produced from aromatic hydrocarbons under EB irradiation. The oxidation process of o-xylene in air and the characteristic of particles produced from xylene were examined by EB irradiation. The particles of products were analyzed under less their coagulation. The use of this EB generator enables to examine the characteristics of particles under irradiation with their analysis immediately after irradiation.

  10. Indefinitely stable iron(IV) cage complexes formed in water by air oxidation

    Science.gov (United States)

    Tomyn, Stefania; Shylin, Sergii I.; Bykov, Dmytro; Ksenofontov, Vadim; Gumienna-Kontecka, Elzbieta; Bon, Volodymyr; Fritsky, Igor O.

    2017-01-01

    In nature, iron, the fourth most abundant element of the Earth's crust, occurs in its stable forms either as the native metal or in its compounds in the +2 or +3 (low-valent) oxidation states. High-valent iron (+4, +5, +6) compounds are not formed spontaneously at ambient conditions, and the ones obtained synthetically appear to be unstable in polar organic solvents, especially aqueous solutions, and this is what limits their studies and use. Here we describe unprecedented iron(IV) hexahydrazide clathrochelate complexes that are assembled in alkaline aqueous media from iron(III) salts, oxalodihydrazide and formaldehyde in the course of a metal-templated reaction accompanied by air oxidation. The complexes can exist indefinitely at ambient conditions without any sign of decomposition in water, nonaqueous solutions and in the solid state. We anticipate that our findings may open a way to aqueous solution and polynuclear high-valent iron chemistry that remains underexplored and presents an important challenge.

  11. Creep performance of oxide ceramic fiber materials at elevated temperature in air and in steam

    Science.gov (United States)

    Armani, Clinton J.

    Structural aerospace components that operate in severe conditions, such as extreme temperatures and detrimental environments, require structural materials that have superior long-term mechanical properties and that are thermochemically stable over a broad range of service temperatures and environments. Ceramic matrix composites (CMCs) capable of excellent mechanical performance in harsh environments are prime candidates for such applications. Oxide ceramic materials have been used as constituents in CMCs. However, recent studies have shown that high-temperature mechanical performance of oxide-oxide CMCs deteriorate in a steam-rich environment. The degradation of strength at elevated temperature in steam has been attributed to the environmentally assisted subcritical crack growth in the oxide fibers. Furthermore, oxide-oxide CMCs have shown significant increases in steady-state creep rates in steam. The present research investigated the effects of steam on the high-temperature creep and monotonic tension performance of several oxide ceramic materials. Experimental facilities were designed and configured, and experimental methods were developed to explore the influence of steam on the mechanical behaviors of ceramic fiber tows and of ceramic bulk materials under temperatures in the 1100--1300°C range. The effects of steam on creep behavior of Nextel(TM)610 and Nextel(TM)720 fiber tows were examined. Creep rates at elevated temperatures in air and in steam were obtained for both types of fibers. Relationships between creep rates and applied stresses were modeled and underlying creep mechanisms were identified. For both types of fiber tows, a creep life prediction analysis was performed using linear elastic fracture mechanics and a power-law crack velocity model. These results have not been previously reported and have critical design implications for CMC components operating in steam or near the recommended design limits. Predictions were assessed and validated via

  12. Influence of superficial oxidation on the pyrophoric behaviour of uranium hydride and uranium powders in air

    Energy Technology Data Exchange (ETDEWEB)

    Ablitzer, C., E-mail: carine.ablitzer@cea.fr [CEA, DEN, DEC/SPUA/LCU, 13108 Saint-Paul lez Durance (France); Le Guyadec, F. [CEA, DEN, DTEC/SDTC, 30207 Bagnols sur Ceze (France); Raynal, J. [CEA, DEN, DEC/SPUA/LCU, 13108 Saint-Paul lez Durance (France); Genin, X. [CEA, DEN, DTEC/SDTC, 30207 Bagnols sur Ceze (France); Duhart-Barone, A. [CEA, DEN, DEC/SPUA/LCU, 13108 Saint-Paul lez Durance (France)

    2013-01-15

    Pyrophoric behaviours in air of uranium hydride and uranium powders have been studied on samples of small mass - several tens of milligrams - in a thermogravimetric device and on samples of several grams in an instrumented furnace. Results show that ignition can occur at room temperature for both materials but only in the second device and provided that powders are not superficially oxidized. Chemisorption of oxygen on particles is suspected to be responsible for ignition at room temperature. This phenomenon is not taken into account in classical theories of ignition. When ignition does not occur at room temperature, it occurs above at least 90 Degree-Sign C when heating at a rate of 5 Degree-Sign C min{sup -1}. Ignition seems then to result principally from the large increase of oxidation rates with temperature.

  13. Association between changes in exposure to air pollution and biomarkers of oxidative stress in children before and during the Beijing Olympics

    NARCIS (Netherlands)

    Lin, Weiwei; Zhu, Tong; Xue, Tao; Peng, Wei; Brunekreef, Bert; Gehring, Ulrike; Huang, Wei; Hu, Min; Zhang, Yuanhang; Tang, Xiaoyan

    2015-01-01

    It is not known whether exposure to air pollutants causes systemic oxidative stress in children. We investigated the association between exposure to air pollution and biomarkers of oxidative stress in relation to a governmental air quality intervention implemented during the 2008 Beijing Olympic Gam

  14. 40 CFR Appendix T to Part 50 - Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Sulfur (Sulfur...

    Science.gov (United States)

    2010-07-01

    ... Ambient Air Quality Standards for Oxides of Sulfur (Sulfur Dioxide) T Appendix T to Part 50 Protection of... AIR QUALITY STANDARDS Pt. 50, App. T Appendix T to Part 50—Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Sulfur (Sulfur Dioxide) 1. General (a) This appendix...

  15. Advanced Oxidation Technologies/Photocatalytic Treatment of Wastewater.

    OpenAIRE

    Chen, J.

    1997-01-01

    7.1. Summary and conclusionsThe last two decennia have shown a growing interest in the photocatalytic treatment of wastewater, and more and more research has been carried out into the various aspects of photocatalysis, varying from highly fundamental aspects to practical application. However, despite all this research, there is still much to investigate. Suggested photocatalytic mechanisms, such as those for oxidation by hydroxyl radicals and for oxidation at the surface of photocatalysts, ne...

  16. Catalytic wet air oxidation of 2-chlorophenol over sewage sludge-derived carbon-based catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Tu, Yuting [Institut de recherches sur la catalyse et l’environnement de Lyon (IRCELYON), CNRS – Université Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France); School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Xiong, Ya; Tian, Shuanghong [School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Guangzhou 510275 (China); Kong, Lingjun [School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Descorme, Claude, E-mail: claude.descorme@ircelyon.univ-lyon1.fr [Institut de recherches sur la catalyse et l’environnement de Lyon (IRCELYON), CNRS – Université Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France)

    2014-07-15

    Highlights: • A sewage sludge derived carbon-supported iron oxide catalyst (FeSC) was prepared. • FeSC exhibited high catalytic activity in the wet air oxidation of 2-chlorophenol. • A strong correlation was observed between the 2-CP conversion, the iron leaching and the pH. • Using an acetate buffer, the iron leaching was suppressed while keeping some catalytic activity. • A simplified reaction pathway was proposed for the CWAO of 2-CP over the FeSC catalyst. - Abstract: A sewage sludge derived carbon-supported iron oxide catalyst (FeSC) was prepared and used in the Catalytic Wet Air Oxidation (CWAO) of 2-chlorophenol (2-CP). The catalysts were characterized in terms of elemental composition, surface area, pH{sub PZC}, XRD and SEM. The performances of the FeSC catalyst in the CWAO of 2-CP was assessed in a batch reactor operated at 120 °C under 0.9 MPa oxygen partial pressure. Complete decomposition of 2-CP was achieved within 5 h and 90% Total Organic Carbon (TOC) was removed after 24 h of reaction. Quite a straight correlation was observed between the 2-CP conversion, the amount of iron leached in solution and the pH of the reaction mixture at a given reaction time, indicating a strong predominance of the homogeneous catalysis contribution. The iron leaching could be efficiently prevented when the pH of the solution was maintained at values higher than 4.5, while the catalytic activity was only slightly reduced. Upon four successive batch CWAO experiments, using the same FeSC catalyst recovered by filtration after pH adjustment, only a very minor catalyst deactivation was observed. Finally, based on all the identified intermediates, a simplified reaction pathway was proposed for the CWAO of 2-CP over the FeSC catalyst.

  17. Oxidative damage to DNA and lipids as biomarkers of exposure to air pollution

    DEFF Research Database (Denmark)

    Møller, Peter; Loft, Steffen

    2010-01-01

    of each of the biomarkers, for total and stratified formal meta-analyses. DATA SYNTHESIS: In the meta-analysis, the standardized mean differences (95% confidence interval) between exposed and unexposed subjects for oxidized DNA and lipids were 0.53 (0.29-0.76) and 0.73 (0.18-1.28) in blood and 0.52 (0......BACKGROUND: Air pollution is thought to exert health effects through oxidative stress, which causes damage to DNA and lipids. OBJECTIVE: We determined whether levels of oxidatively damaged DNA and lipid peroxidation products in cells or bodily fluids from humans are useful biomarkers.......22-0.82) and 0.49 (0.01-0.97) in urine, respectively. The standardized mean difference for oxidized lipids was 0.64 (0.07-1.21) in the airways. Restricting analyses to studies unlikely to have substantial biomarker or exposure measurement error, studies likely to have biomarker and/or exposure error, or studies...

  18. Photocatalytic Removal of Formaldehyde from Air Using Titanium Oxide-Reduced Graphene Composite

    Directory of Open Access Journals (Sweden)

    N Rastkari

    2016-06-01

    Full Text Available Background and Objective: Formaldehyde is a toxic volatile organic compound, which its removal from polluted air is essential. One of the techniques available for removing such compounds is photocatalytic degradation. The aim of this study was to investigate the photocatalytic degradation of gaseous formaldehyde on TiO2 nanoparticles coated on reduced graphene oxide Materials and Methods: The synthesized reduced graphene oxide- TiO2 nanocomposite was characterized using SEM, EDS, and FTIR spectra. The photocatalytic activity of prepared reduced graphene oxide- TiO2 nanocomposite was investigated for degradation of gaseous toluene under different operational conditions such as different initial concentration, flow rate, and time. Results: The photocatalytic degradation efficiency of the RGO-TiO2 nanocomposite was much higher than P25 TiO2. The photocatalytic degradation efficiency of the RGO-TiO2 nanocomposite decreased by increasing the flow rate so the flow rate is a key factor for the use of RGO-TiO2 nanocomposite as a photocatalyst. The results showed that the photocatalytic degradation rates decreased from 89 to 30% with increasing formaldehyde initial concentration from 0.1 to 1 ppm. Conclusion: This research indicated that RGO-TiO2 nanocomposite can be effectively used as suitable photocatalyst to remove gaseous pollutants. One of the advantages of the as-prepared composite was using visible light instead of UV to activate the oxidation process.

  19. Catalytic wet air oxidation of phenol with functionalized carbon materials as catalysts: reaction mechanism and pathway.

    Science.gov (United States)

    Wang, Jianbing; Fu, Wantao; He, Xuwen; Yang, Shaoxia; Zhu, Wanpeng

    2014-08-01

    The development of highly active carbon material catalysts in catalytic wet air oxidation (CWAO) has attracted a great deal of attention. In this study different carbon material catalysts (multi-walled carbon nanotubes, carbon fibers and graphite) were developed to enhance the CWAO of phenol in aqueous solution. The functionalized carbon materials exhibited excellent catalytic activity in the CWAO of phenol. After 60 min reaction, the removal of phenol was nearly 100% over the functionalized multi-walled carbon, while it was only 14% over the purified multi-walled carbon under the same reaction conditions. Carboxylic acid groups introduced on the surface of the functionalized carbon materials play an important role in the catalytic activity in CWAO. They can promote the production of free radicals, which act as strong oxidants in CWAO. Based on the analysis of the intermediates produced in the CWAO reactions, a new reaction pathway for the CWAO of phenol was proposed in this study. There are some differences between the proposed reaction pathway and that reported in the literature. First, maleic acid is transformed directly into malonic acid. Second, acetic acid is oxidized into an unknown intermediate, which is then oxidized into CO2 and H2O. Finally, formic acid and oxalic acid can mutually interconvert when conditions are favorable.

  20. The cyclic oxidation behavior of the single crystal TMS-82+ superalloy in humidified air

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Y. [School of Materials Science and Engineering, Shanghai, Institute of Technology, Shanghai (China); Research Group of Interface Control Engineering, Graduate School of Engineering, Hokkaido University, Sapporo (Japan); Narita, T. [Research Group of Interface Control Engineering, Graduate School of Engineering, Hokkaido University, Sapporo (Japan)

    2009-10-15

    The cyclic oxidation behavior of a single crystal Ni-based superalloy TMS-82+ was studied at 800 and 900 C for 200 h in water vapor (air plus 15% H{sub 2}O). Regardless of the exposure temperature, time-dependence of the growth rate of the scale for the superalloy was fitted by a subparabolic relationship. The oxidation rate was enhanced with increase in exposure temperature, which was evidenced by a higher mass gain and thicker scale. The oxides on the specimen at 800 C consisted of (Ni,Co)O, CrTaO{sub 4}, AlTaO{sub 4}, Cr{sub 2}O{sub 3}, and {theta}-Al{sub 2}O{sub 3}, whereas for the specimen exposed at 900 C, spinels of NiCr{sub 2}O{sub 4} and (Ni,Co)Al{sub 2}O{sub 4} as well as {alpha}-Al{sub 2}O{sub 3} were observed. An innermost dense {alpha}-Al{sub 2}O{sub 3} layer was responsible for a stable growth rate of the scale after the initial rapid oxidation. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  1. The reaction jet technology of air-to-air missiles%空空导弹直接力控制技术

    Institute of Scientific and Technical Information of China (English)

    高建军

    2011-01-01

    为了实现空空导弹大机动飞行,采用直接力控制技术。本文介绍了直接力控制技术在多种拦截弹上的使用情况,并分析了其各种关键技术,以利于将来大机动空空导弹的设计工作。%For the high maneuverability flight of air-to-air missiles, the reaction jet technology is used. In order to design the new air-to-air missiles of high maneuverability, it is introduced in this paper how the reaction jet technology is used in many missiles, and many key technologies about the reaction jet are analyzed in it.

  2. Cleaning mechanism of particle contaminants on large aperture optical components by using air knife sweeping technology

    Science.gov (United States)

    Niu, Longfei; Liu, Hao; Miao, Xinxiang; Lv, Haibing; Yuan, Xiaodong; Zhou, Hai; Yao, Caizhen; Zhou, Guorui; Li, Qin

    2017-05-01

    The cleaning mechanism of optical surface particle contaminants in the light pneumatic tube was simulated based on the static equations and JKR model. Cleaning verification experiment based on air knife sweeping system and on-line monitoring system in high power laser facility was set up in order to verify the simulated results. Results showed that the removal ratio is significantly influenced by sweeping velocity and angle. The removal ratio can reach to 94.3% by using higher input pressure of the air knife, demonstrating that the air knife sweeping technology is useful for maintaining the surface cleanliness of optical elements, and thus guaranteeing the long-term stable running of the high power laser facility.

  3. The application of active noise control technology to reduce noise from air pollution control equipment

    Energy Technology Data Exchange (ETDEWEB)

    Depies, C. R.; Kapsos, D. W.

    1996-08-01

    The basic concept of active noise control, i. e. to create a noise field in a space in order to destructively interfere with an existing noise, and in the process create a quieter space, was explained. The manner in which noise control technology can be used in air pollution control equipment was described and guidelines for application were provided. A number of case studies were used to illustrate the suitability of active noise control for low frequency noise problems, especially in the area of air pollution control equipment. Impressive reduction of low frequency noise, energy efficiency, ability to retrofit into an existing duct system, and the hardware`s insensitivity to dirty exhaust environments were cited as the principal reasons for the success of active noise control technology over more traditional in-line passive silencers. 1 ref., 8 figs.

  4. Future Capabilities and Technologies for the Air Force in 2030. Executive Summary

    Science.gov (United States)

    2009-07-01

    as a foil to evaluate future systems and technologies, to deter- mine the optimum path forward for Air Force investment. These senior officers each...attacks are being designed to degrade adversary command and control and early- warning capabilities. Finally, submarines, destroyers, aircraft, mines ...Paralysis in Military Operations Jan S. Breemer, December 2000 20 Using Lasers in Space: Laser Orbital Debris Removal and Asteroid Deflection Jonathon

  5. Treatment of desizing wastewater from the textile industry by wet air oxidation

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper describes the application of wet air oxidation to the treatment of desizing wastewater from two textile companies. A two-liter high temperature, high pressure autoclave reactor was used in the study. The range of operating temperatures examined was between 150 and 290℃, and the partial pressure of oxygen ranged from 0. 375 to 2.25 MPa. Variations in pH,CODCr and TOD content were monitored during each experiment and used to assess the extent of conversion of the process. The effects of temperature, pressure and reaction time were explored extensively. More than 90 % CODCr reduction and 80 % TOC removal have been obtained. The results have also been demonstrated that WAO is a suitable pre-treatment methods due to improvement of the BOD5/CODCr ratio of desizing wastewater. The reaction kinetics of wet air oxidation of desizing wastewater has been proved to be two steps, a fast reaction followed by a slow reaction stage.

  6. Kinetics of Wet Air Oxidation of Wastewater from Natural Fiber Web Desizing

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This work described the application of wet air oxidation (WAO) to the treatment of desizing wastewater from natural fiber processing. A two-liter autoclave batch reactor was used for the experiments. The range of operating temperature examined was between 150 and 290℃, and partial pressure of oxygen ranged from 0.375 to 2.25 MPa standardized at 25℃. Variations in Chemical Oxygen Demand(COD) and Total Organic Carbon(TOC) were monitored during each experiment and used to assess the performance of the process. Experimental results showed that WAO can be an efficient method for the treatment of desizing wnstewater. Furthermore, Catalytic Wet Air Oxidation (CWAO) was applied to reduce the reaction temperature and pressure in WAO process. A higher COD removal ratio was achieved under more mild reaction condition with the aid of CWAO. A mathematical model was also proposed to simulate the WAO process of desizing wastewater, in which three distinct kinetics steps were considered to describe the degradation of starch. The model simulations were in well agreement with the experimental data.

  7. Alkaline peroxide assisted wet air oxidation pretreatment approach to enhance enzymatic convertibility of rice husk.

    Science.gov (United States)

    Banerjee, Saumita; Sen, Ramkrishna; Mudliar, Sandeep; Pandey, R A; Chakrabarti, Tapan; Satpute, Dewanand

    2011-01-01

    Pretreatment of rice husk by alkaline peroxide assisted wet air oxidation (APAWAO) approach was investigated with the aim to enhance the enzymatic convertibility of cellulose in pretreated rice husk. Rice husk was presoaked overnight in 1% (w/v) H(2)O(2) solution (pH adjusted to 11.5 using NaOH) (equivalent to 16.67 g H(2)O(2) and 3.63 g NaOH per 100 g dry, untreated rice husk) at room temperature, followed by wet air oxidation (WAO). APAWAO pretreatment resulted in solubilization of 67 wt % of hemicellulose and 88 wt % of lignin initially present in raw rice husk. Some amount of oligomeric glucose (˜8.3 g/L) was also observed in the APAWAO liquid fraction. APAWAO pretreatment resulted in 13-fold increase in the amount of glucose that could be obtained from otherwise untreated rice husk. Up to 86 wt % of cellulose in the pretreated rice husk (solid fraction) could be converted into glucose within 24 hours, yielding over 21 g glucose per 100 g original rice husk. Scanning electron microscopy was performed to visualize changes in biomass structure following the APAWAO pretreatment. Enzymatic cellulose convertibility of the pretreated slurry at high dry matter loadings was also investigated.

  8. Air Traffic Management Technology Demostration: 1 Research and Procedural Testing of Routes

    Science.gov (United States)

    Wilson, Sara R.; Kibler, Jennifer L.; Hubbs, Clay E.; Smail, James W.

    2015-01-01

    NASA's Air Traffic Management Technology Demonstration-1 (ATD-1) will operationally demonstrate the feasibility of efficient arrival operations combining ground-based and airborne NASA technologies. The ATD-1 integrated system consists of the Traffic Management Advisor with Terminal Metering which generates precise time-based schedules to the runway and merge points; Controller Managed Spacing decision support tools which provide controllers with speed advisories and other information needed to meet the schedule; and Flight deck-based Interval Management avionics and procedures which allow flight crews to adjust their speed to achieve precise relative spacing. Initial studies identified air-ground challenges related to the integration of these three scheduling and spacing technologies, and NASA's airborne spacing algorithm was modified to address some of these challenges. The Research and Procedural Testing of Routes human-in-the-loop experiment was then conducted to assess the performance of the new spacing algorithm. The results of this experiment indicate that the algorithm performed as designed, and the pilot participants found the airborne spacing concept, air-ground procedures, and crew interface to be acceptable. However, the researchers concluded that the data revealed issues with the frequency of speed changes and speed reversals.

  9. Technological, economic, and political feasibility in OSHA's Air Contaminants Standard

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, J.C.; Paxman, D.G. (Univ. of California, Berkeley (USA))

    In 1989, after almost two decades of substance-by-substance standard setting, the Occupational Safety and Health Administration (OSHA) promulgated its Air Contaminants Standard, imposing new exposure limits for 376 toxic substances encountered in U.S. industry. In marked contrast to earlier regulations, the Air Contaminants Standard has generated relatively little industry opposition. This paper analyzes the standard in the context of the twenty-year debate over the appropriate role for technological feasibility and economic compliance costs in occupational health policy. The political feasibility of the new standard is traced to OSHA's abandonment of technology forcing in favor of reliance on off-the-shelf technologies already in use in major firms. While important as an embodiment of OSHA's new generic approach to regulation, the Air Contaminants Standard cannot serve as a model for future occupational health policy, due to its reliance on informal, closed-door mechanisms for establishing regulatory priorities and permissible exposure limits. 20 refs.

  10. Long-term impacts of air capture technologies on optimal climate strategies under economic uncertainties

    Science.gov (United States)

    Ghasemi, F.

    2014-12-01

    Despite widespread attention to the consequences of climate change, tangible and concerted progress toward mitigation of the adverse effects of greenhouse-gas (GHG) emissions has yet to be coordinated among various national and international agents. The energy objectives set by such initiatives as 'Sustainable Energy for All' partially help slow down the global warming in short term, but the risks posed by GHG emissions would persist for a long time. This fact makes negative emission solutions more appealing as a part of the climate protection efforts. Here I use integrated assessment modeling to investigate the potential added value of air capture technologies as a complement for more conventional solutions such as carbon capture and storage, and the use of renewables. Thermodynamic limits of air capture technologies are used as a general guideline for the estimation of the performance of air capture technologies. Optimal long-run climate strategies are discussed taking into account the uncertainties in the impact of CO2 concentration on the Global Wealth Product, and possible scenarios that result in an overshoot beyond the 2°C warming limit.

  11. Novel transparent conducting oxide technology for solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, P.T.; Sutton, P.A.; Gardener, M.; Wakefield, G.

    2005-07-01

    This report outlines the development of both n- and p-type transparent Conducting Oxide (TCO) materials and the demonstrated feasibility of economic production of TCO films by deposition techniques. Descriptions are given of the four main tasks of the project with Task A concentrating on material design and synthesis covering the new precursor to zinc oxide thin films and selection of polymers for formulation; Task B dealing with film formation involving film deposition by spin coating, screen printing, inkjet printing, dip coating and chemical vapour deposition; Task C concerning performance evaluation; and Task D examining manufacturing process development. The prospects for commercialisation are explored and recommendation for future work are considered.

  12. Identification of Air Force Emerging Technologies and Militarily Significant Emerging Technologies.

    Science.gov (United States)

    1985-08-31

    lithium thionyl chloride from one to two hours. Thus, lithium technology is allowing primary and reserve batteries to achieve rates and times...current batteries . Lithium chloride is one such candidate. Lithium chloride is a high temperature battery with a power density of 16 Amps/cm2 at 2.5 volts...missile guidance seekers. Lithium chloride batteries capable of achieving 40 watts/cm2 is still in early 6.2 develop- mental research

  13. Exposure to Fine Particulate Air Pollution Causes Vascular Insulin Resistance by Inducing Pulmonary Oxidative Stress.

    Science.gov (United States)

    Haberzettl, Petra; O'Toole, Timothy E; Bhatnagar, Aruni; Conklin, Daniel J

    2016-12-01

    Epidemiological evidence suggests that exposure to ambient air fine particulate matter (PM2.5) increases the risk of developing type 2 diabetes and cardiovascular disease. However, the mechanisms underlying these effects of PM2.5 remain unclear. We tested the hypothesis that PM2.5 exposure decreases vascular insulin sensitivity by inducing pulmonary oxidative stress. Mice fed control (10-13% kcal fat) and high-fat (60% kcal fat, HFD) diets, treated with 4-hydroxy-2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPOL) or mice overexpressing lung-specific extracellular superoxide dismutase (ecSOD) were exposed to HEPA-filtered air or to concentrated PM2.5 (CAP) for 9 or 30 days, and changes in systemic and organ-specific insulin sensitivity and inflammation were measured. In control diet-fed mice, exposure to CAP for 30 days decreased insulin-stimulated Akt phosphorylation in lung, heart, and aorta but not in skeletal muscle, adipose tissue, and liver and did not affect adiposity or systemic glucose tolerance. In HFD-fed mice, 30-day CAP exposure suppressed insulin-stimulated endothelial nitric oxide synthase (eNOS) phosphorylation in skeletal muscle and increased adipose tissue inflammation and systemic glucose intolerance. In control diet-fed mice, a 9-day CAP exposure was sufficient to suppress insulin-stimulated Akt and eNOS phosphorylation and to decrease IκBα (inhibitor of the transcription factor NF-κB levels in the aorta. Treatment with the antioxidant TEMPOL or lung-specific overexpression of ecSOD prevented CAP-induced vascular insulin resistance and inflammation. Short-term exposure to PM2.5 induces vascular insulin resistance and inflammation triggered by a mechanism involving pulmonary oxidative stress. Suppression of vascular insulin signaling by PM2.5 may accelerate the progression to systemic insulin resistance, particularly in the context of diet-induced obesity. Citation: Haberzettl P, O'Toole TE, Bhatnagar A, Conklin DJ. 2016. Exposure to fine

  14. New and Emerging Technologies for Real-Time Air and Surface Beryllium Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Phifer, B.E. Jr.; Churnetski, E.L.; Cooke, L.E.; Reed, J.J.; Howell, M.L.; Smith, V.D.

    2001-09-01

    In this study, five emerging technologies were identified for real-time monitoring of airborne beryllium: Microwave-Induced Plasma Spectroscopy (MIPS), Aerosol Beam-Focused Laser-Induced Plasma Spectroscopy (ABFLIPS), Laser-Induced Breakdown Spectroscopy (LIBS), Surfaced-Enhanced Raman Scattering (SERS) Spectroscopy, and Micro-Calorimetric Spectroscopy (CalSpec). Desired features of real-time air beryllium monitoring instrumentation were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies as well as their unique demonstrated capability to provide real-time monitoring of similar materials. However, best available technologies were considered, regardless of their ability to comply with the desired features. None of the five technologies have the capability to measure the particle size of airborne beryllium. Although reducing the total concentration of airborne beryllium is important, current literature suggests that reducing or eliminating the concentration of respirable beryllium is critical for worker health protection. Eight emerging technologies were identified for surface monitoring of beryllium. CalSpec, MIPS, SERS, LIBS, Laser Ablation, Absorptive Stripping Voltametry (ASV), Modified Inductively Coupled Plasma (ICP) Spectroscopy, and Gamma BeAST. Desired features of real-time surface beryllium monitoring were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies. However, the best available technologies were considered regardless of their ability to comply with the desired features.

  15. Oxidative potential and inflammatory impacts of source apportioned ambient air pollution in Beijing.

    Science.gov (United States)

    Liu, Qingyang; Baumgartner, Jill; Zhang, Yuanxun; Liu, Yanju; Sun, Yongjun; Zhang, Meigen

    2014-11-01

    Air pollution exposure is associated with a range of adverse health impacts. Knowledge of the chemical components and sources of air pollution most responsible for these health effects could lead to an improved understanding of the mechanisms of such effects and more targeted risk reduction strategies. We measured daily ambient fine particulate matter (Beijing, and assessed the contribution of its chemical components to the oxidative potential of ambient air pollution using the dithiothreitol (DTT) assay. The composition data were applied to a multivariate source apportionment model to determine the PM contributions of six sources or factors: a zinc factor, an aluminum factor, a lead point factor, a secondary source (e.g., SO4(2-), NO3(2-)), an iron source, and a soil dust source. Finally, we assessed the relationship between reactive oxygen species (ROS) activity-related PM sources and inflammatory responses in human bronchial epithelial cells. In peri-urban Beijing, the soil dust source accounted for the largest fraction (47%) of measured ROS variability. In central Beijing, a secondary source explained the greatest fraction (29%) of measured ROS variability. The ROS activities of PM collected in central Beijing were exponentially associated with in vivo inflammatory responses in epithelial cells (R2=0.65-0.89). We also observed a high correlation between three ROS-related PM sources (a lead point factor, a zinc factor, and a secondary source) and expression of an inflammatory marker (r=0.45-0.80). Our results suggest large differences in the contribution of different PM sources to ROS variability at the central versus peri-urban study sites in Beijing and that secondary sources may play an important role in PM2.5-related oxidative potential and inflammatory health impacts.

  16. The effect of various types of cement dust on sulphur dioxide oxidation in the air.

    Science.gov (United States)

    Vadjić, V; Gentilizza, M; Halle, R

    1988-07-01

    The effect of various types of cement dust on the behaviour of sulphur dioxide in the air was investigated on model systems in different experimental conditions.Experiments were carried out with PC-15z-45s (Portland-blast furnace cement containing 15% blast furnace slag), PC-25p-35s (Portland-pozzolan cement containing 25% pozzolan) and EFD (electrofilter dust).EFD most effectively removed SO2 from the air stream. The next efficacious was PC-15z-45s, whereas PC-25p-35s was the least efficient. The efficacy of cement dusts for SO2 removal from the air stream depended on their chemical and granulometric composition and in particular on the size of specific surface.The rate of reaction was also influenced by experimental conditions-relative humidity, the length of contact, that is, the flow rate of gaseous mixture through the reactor, and the amount of cement dust.The experimental data show that in the contact between SO2 and cement dust catalytic oxidation of SO2 to sulphates takes place. Sulphates remain bound to the surface, from which they cannot be thermally desorbed, but can be released by extraction in the Soxhlet apparatus.

  17. Gestational diabetes mellitus was related to ambient air pollutant nitric oxide during early gestation.

    Science.gov (United States)

    Pan, Shih-Chun; Huang, Ching-Chun; Lin, Shio-Jean; Chen, Bing-Yu; Chang, Chang-Chuan; Leon Guo, Yue-Liang

    2017-10-01

    Ambient air pollution has been linked to the risk of gestational diabetes mellitus (GDM). However, evidence of this association is limited, and no study has examined the effects of nitric oxide (NO). This study investigated the association between air pollution exposure during gestation and GDM. The Taiwan Birth Cohort Study database was used to examine the association between the risk of GDM and all routinely monitored air pollutants among 21,248 women who were pregnant during 2004-2005. We further employed a two-pollutant model for confirming the effect of each pollutant on GDM. After the exclusion criteria were applied, 19,606 women were included in the final analysis. Among them, 378 (1.9%) had been diagnosed as having GDM. These women were older and had higher BMIs than the women without GDM. The risks of GDM onset were significantly associated with NO exposure during the first [adjusted OR (aOR): 1.05, 95% confidence interval (CI): 1.02-1.08] and second (aOR: 1.05, 95%CI: 1.02-1.08) trimesters. Under the two-pollutant model, the effect of NO exposure was also significant during the first (aOR: 1.05, 95%CI: 1.02-1.08) and second (aOR: 1.05, 95%CI: 1.02-1.09) trimesters. The results indicated that exposure to higher NO levels during pregnancy increases the risk of GDM. Copyright © 2017. Published by Elsevier Inc.

  18. Nitrous oxide supersaturation at the liquid/air interface of animal waste

    Energy Technology Data Exchange (ETDEWEB)

    Makris, Konstantinos C., E-mail: kcmakris@gmail.co [Cyprus International Institute for the Environment and Public Health in association with the Harvard School of Public Health, 5 Iroon Street, Nicosia 1105 (Cyprus); Andra, Syam S. [Environmental Geochemistry Laboratory, University of Texas at San Antonio, San Antonio, TX (United States); Hardy, Michael; Sarkar, Dibyendu [Department of Earth and Environmental Studies, Montclair State University, Montclair, NJ (United States); Datta, Rupali [Department of Biological Sciences, Michigan Technological University, Houghton, MI (United States); Bach, Stephan B.H.; Mullens, Conor P. [Department of Chemistry, University of Texas at San Antonio, San Antonio, TX (United States)

    2009-12-15

    Concentrated animal feeding operations around the globe generate large amounts of nitrous oxide (N{sub 2}O) in the surrounding atmosphere. Liquid animal waste systems have received little attention with respect to N{sub 2}O emissions. We hypothesized that the solution chemistry of animal waste aqueous suspensions would promote conditions that lead to N{sub 2}O supersaturation at the liquid/air interface. The concentration of dissolved N{sub 2}O in poultry litter (PL) aqueous suspensions at 25 deg. C was 0.36 mug N{sub 2}O mL{sup -1}, at least an order of magnitude greater than that measured in water in equilibrium with ambient air, suggesting N{sub 2}O supersaturation. There was a nonlinear increase in the N{sub 2}O Henry constants of PL from 2810 atm/mole fraction at 35 deg. C to 17 300 atm/mole fraction at 41 deg. C. The extremely high N{sub 2}O Henry constants were partially ascribed to N{sub 2}O complexation with aromatic moieties. Complexed N{sub 2}O structures were unstable at temperatures > 35 deg. C, supplying the headspace with additional free N{sub 2}O concentrations. - Temperature-dependent N{sub 2}O supersaturation at the liquid/air interface of animal waste.

  19. Biomarkers of occupational exposure to air pollution, inflammation and oxidative damage in taxi drivers.

    Science.gov (United States)

    Brucker, Natália; Moro, Angela M; Charão, Mariele F; Durgante, Juliano; Freitas, Fernando; Baierle, Marília; Nascimento, Sabrina; Gauer, Bruna; Bulcão, Rachel P; Bubols, Guilherme B; Ferrari, Pedro D; Thiesen, Flávia V; Gioda, Adriana; Duarte, Marta M M F; de Castro, Iran; Saldiva, Paulo H; Garcia, Solange C

    2013-10-01

    Exposure to environmental pollutants has been recognised as a risk factor for cardiovascular events. 1-hydroxypyrene (1-OHP) is a biomarker of exposure to polycyclic aromatic hydrocarbons (PAHs) from traffic-related air pollution. Experimental studies indicate that PAH exposure could be associated with inflammation and atherogenesis. Thus, the purpose of this study was to evaluate whether the biomarker of PAH exposure is associated with biomarkers of inflammation and oxidative stress and if these effects modulate the risk of developing cardiovascular diseases in workers exposed to air pollution. This study included 60 subjects, comprising 39 taxi drivers and 21 non-occupationally exposed persons. Environmental PM2.5 and benzo[a]pyrene (BaP) levels, in addition to biomarkers of exposure and oxidative damage, were determined. Inflammatory cytokines (IL-1β, IL-6, IL-10, TNF-α, IFN-γ and hs-CRP) and serum levels of oxidised LDL (ox-LDL), auto-antibodies (ox-LDL-Ab) and homocysteine (Hcy) were also evaluated. PM2.5 and BaP exhibited averages of 12.4±6.9 μg m(-3) and 1.0±0.6 ng m(-3), respectively. Urinary 1-OHP levels were increased in taxi drivers compared to the non-occupationally exposed subjects (ptaxi drivers had elevated pro-inflammatory cytokines, biomarkers of oxidative damage, and ox-LDL, ox-LDL-Ab and Hcy levels, although antioxidant enzymes were decreased compared to the non-occupationally exposed subjects (ptaxi drivers showed major exposure to pollutants, such as PAHs, in relation to non-occupationally exposed subjects. This finding was associated with higher inflammatory biomarkers and Hcy, which represent important predictors for cardiovascular events. These data suggest a contribution of PAHs to cardiovascular diseases upon occupational exposure. © 2013.

  20. Conversion of the refractory ammonia and acetic acid in catalytic wet air oxidation of animal byproducts

    Institute of Scientific and Technical Information of China (English)

    Virginie Fontanier; Sofiane Zalouk; Stéphane Barbati

    2011-01-01

    Wet air oxidation (WAO) and catalytic wet air oxidation (CWAO) of slaughtered animal byproducts (ABPs) were investigated.Two step experiment was carried out consisting ofa non-catalysed WAO run followed by a CWAO run at 170-275℃, 20 MPa, and reaction time 180 min.The WAO (1st step) of sample (5 g/L total organic carbon (TOC)) yielded (82.0 ± 4)% TOC removal and (78.4 ± 13.2)%conversion of the initial organic-N into NH4+-N.Four metal catalysts (Pd, Pt, Rh, Ru) supported over alumina have been tested in catalytic WAO (2nd step) at elevated pH to enhance ammonia conversion and organic matter removal, particularly acetic acid.It was found that the catalysts Ru, Pt, and Rh had significant effects on the TOC removal (95.1%, 99.5% and 96.7%, respectively) and on the abatement of ammonia (93.4%, 96.7% and 96.3%, respectively) with high nitrogen selectivity.The catalyst Pd was found to have the less activity while Pt had the best performance.The X-Ray diffraction analysis showed that the support of catalyst was not stable under the experimental conditions since it reacted with phosphate present in solution.Nitrite and nitrate ions were monitored during the oxidation reaction and it was concluded that CWAO of ammonia in real waste treatment framework was in good agreement with the results obtained from the literature for ideal solutions of ammonia.

  1. Kinetics of Zr-alloy cladding oxidation in the mixture of air and steam at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyung Tae; Park, Kwang Heon; Park, Joo Young [Kyunghee University, Yongin (Korea, Republic of)

    2012-05-15

    In Fukushima Daiichi Nuclear Power Plant accident, No.4 plant was exploded by hydrogen explosion. There was a strong speculation about the possibility of the reaction between the overheated fuels and the steam-air mixture in the storage pool. Later, it turned out to be due to the hydrogen leaked from No.3 plant. However, the reaction of the hot fuels with the steam-air mixture became an important issue. There have been a lot of data accumulated about Zr-alloy interaction with steam. However, Zr-alloy interactions with air and steam-air mixtures have not been studied relatively much. In this study, we measured the oxidation kinetics of Zry-4 and Zirlo claddings in air, and steam-air mixtures, and analyzed the kinetics

  2. Treatment of biomass gasification wastewater using a combined wet air oxidation/activated sludge process

    Energy Technology Data Exchange (ETDEWEB)

    English, C.J.; Petty, S.E.; Sklarew, D.S.

    1983-02-01

    A lab-scale treatability study for using thermal and biological oxidation to treat a biomass gasification wastewater (BGW) having a chemical oxygen demand (COD) of 46,000 mg/l is described. Wet air oxidation (WA0) at 300/sup 0/C and 13.8 MPa (2000 psi) was used to initially treat the BGW and resulted in a COD reduction of 74%. This was followed by conventional activated sludge treatment using operating conditions typical of municipal sewage treatment plants. This resulted in an additional 95% COD removal. Overall COD reduction for the combined process was 99%. A detailed chemical analysis of the raw BGW and thermal and biological effluents was performed using gas chromatography/mass spectrometry (GC/MS). These results showed a 97% decrease in total extractable organics with WA0 and a 99.6% decrease for combined WA0 and activated sludge treatment. Components of the treated waters tended to be fewer in number and more highly oxidized. An experiment was conducted to determine the amount of COD reduction caused by volatilization during biological treatment. Unfortunately, this did not yield conclusive results. Treatment of BGW using WA0 followed by activated sludge appears to be very effective and investigations at a larger scale are recommended.

  3. Catalytic wet-air oxidation of a chemical plant wastewater over platinum-based catalysts.

    Science.gov (United States)

    Cybulski, Andrzej; Trawczyński, Janusz

    2006-01-01

    Catalytic wet-air oxidation (CWAO) of wastewater (chemical oxygen demand [COD] = 1800 mg O2/dm3) from a fine chemicals plant was investigated in a fixed-bed reactor at T = 393-473 K under total pressure of 5.0 or 8.0 MPa. Catalysts containing 0.3% wt. of platinum deposited on two supports, mixed silica-titania (SM1) and carbon black composites (CBC) were used. The CBC-supported catalyst appeared to be more active than the SM1-supported one. A slow decrease of activity of the platinum on SM1 (Pt-SM1) during the long-term operation is attributed to recrystallization of titania and leaching of a support component, while the Pt-CBC catalyst is deteriorated, owing to combustion of the support component. The power-law-kinetic equations were used to describe the rate of COD removal at CWAO over the catalysts. The kinetic parameters of COD reduction for the wastewater were determined and compared with the kinetic parameters describing phenol oxidation over the same catalysts. Rates of COD removal for the wastewater were found higher than those for phenol oxidation over the same catalysts and under identical operating conditions.

  4. Effects of operational conditions on sludge degradation and organic acids formation in low-critical wet air oxidation.

    Science.gov (United States)

    Chung, Jinwook; Lee, Mikyung; Ahn, Jaehwan; Bae, Wookeun; Lee, Yong-Woo; Shim, Hojae

    2009-02-15

    Wet air oxidation processes are to treat highly concentrated organic compounds including refractory materials, sludge, and night soil, and usually operated at supercritical water conditions of high temperature and pressure. In this study, the effects of operational conditions including temperature, pressure, and oxidant dose on sludge degradation and conversion into subsequent intermediates such as organic acids were investigated at low critical wet oxidation conditions. The reaction time and temperature in the wet air oxidation process was shown an important factor affecting the liquefaction of volatile solids, with more significant effect on the thermal hydrolysis reaction rather than the oxidation reaction. The degradation efficiency of sludge and the formation of organic acids were improved with longer reaction time and higher reaction temperature. For the sludge reduction and the organic acids formation under the wet air oxidation, the optimal conditions for reaction temperature, time, pressure, and oxidant dose were shown approximately 240 degrees C, 30min, 60atm, and 2.0L/min, respectively.

  5. Direct gas-phase epoxidation of propylene to propylene oxide using air as oxidant on supported gold catalyst

    Institute of Scientific and Technical Information of China (English)

    Zhanghuai Suo; Mingshan Jin; Jiqing Lu; Zhaobin Wei; Can Li

    2008-01-01

    Gold catalysts supported on SiO2, TiO2, TiO2-SiO2, and ZrO2-SiO2 supports were prepared by impregnating each support with a basic solution of tetrachloroauric acid. X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) techniques were used to characterize their structure and surface composition. The results indicated that the size of gold particles could be controlled to below 10 nm by this method of preparation. Washing gold catalysts with water could markedly enhance the dispersion of metallic gold particles on the surface, but it could not completely remove the chloride ions left on the surface. The catalytic performance of direct vapor-phase epoxidation of propylene using air as an oxidant over these catalysts was evaluated at atmospheric pressure. The selectivity to propylene oxide (PO) was found to vary with reaction time on the stream. At the reaction conditions of atmosphere pressure, temperature 325 ℃, feed gas ratio V(C3H6)/V(O2) = 1/2, and GHSV = 6000 h-1, 17.9% PO selectivity with 0.9% propylene conversion were obtained at initial 10 min for Au/SiO2 catalyst. After reacting 60 min only 8.9% PO selectivity were detected, but the propylene conversion rises to 1.4% and the main product is transferred to acrolein (72% selectivity). Washing Au/TiO2-SiO2 and Au/ZrO2-SiO2 samples with magnesium citrate solution could markedly enhance the activity and PO selectivity because smaller gold particles were obtained.

  6. Direct Air Capture of CO2 - an Overview of Carbon Engineering's Technology and Pilot Plant Development

    Science.gov (United States)

    Holmes, G.; Corless, A.

    2014-12-01

    At Carbon Engineering, we are developing and commercializing technology to scrub CO2 directly from atmospheric air at industrial scale. By providing atmospheric CO2 for use in fuel production, we can enable production of transportation fuels with ultra-low carbon intensities, which command price premiums in the growing set of constrained fuels markets such as California's LCFS. We are a Calgary based startup founded in 2009 with 10 employees, and we are considered a global leader in the direct air capture (DAC) field. We will review CE's DAC technology, based on a wet-scrubbing "air contactor" which absorbs CO2 into aqueous solution, and a chemical looping "regeneration" component, which liberates pure CO2 from this aqueous solution while re-making the original absorption chemical. CE's DAC tecnology exports purified atmospheric CO2, combined with the combustion CO2 from plant energy usage, as the end product. We will also discuss CE's 2014-2015 end-to-end Pilot Demonstration Unit. This is a $7M technology demonstration plant that CE is building with the help of key industrial partners and equipment vendors. Vendor design and engineering requirements have been used to specify the pilot air contactor, pellet reactor, calciner, and slaker modules, as well as auxiliary systems. These modules will be run for several months to obtain the engineering and performance data needed for subsequent commercial plant design, as well as to test the residual integration risks associated with CE's process. By the time of the AGU conference, the pilot is expected to be in late stages of fabrication or early stages of site installation.

  7. Detection and removal of impurities in nitric oxide generated from air by pulsed electrical discharge.

    Science.gov (United States)

    Yu, Binglan; Blaesi, Aron H; Casey, Noel; Raykhtsaum, Grigory; Zazzeron, Luca; Jones, Rosemary; Morrese, Alexander; Dobrynin, Danil; Malhotra, Rajeev; Bloch, Donald B; Goldstein, Lee E; Zapol, Warren M

    2016-11-30

    Inhalation of nitric oxide (NO) produces selective pulmonary vasodilation without dilating the systemic circulation. However, the current NO/N2 cylinder delivery system is cumbersome and expensive. We developed a lightweight, portable, and economical device to generate NO from air by pulsed electrical discharge. The objective of this study was to investigate and optimize the purity and safety of NO generated by this device. By using low temperature streamer discharges in the plasma generator, we produced therapeutic levels of NO with very low levels of nitrogen dioxide (NO2) and ozone. Despite the low temperature, spark generation eroded the surface of the electrodes, contaminating the gas stream with metal particles. During prolonged NO generation there was gradual loss of the iridium high-voltage tip (-90 μg/day) and the platinum-nickel ground electrode (-55 μg/day). Metal particles released from the electrodes were trapped by a high-efficiency particulate air (HEPA) filter. Quadrupole mass spectroscopy measurements of effluent gas during plasma NO generation showed that a single HEPA filter removed all of the metal particles. Mice were exposed to breathing 50 parts per million of electrically generated NO in air for 28 days with only a scavenger and no HEPA filter; the mice did not develop pulmonary inflammation or structural changes and iridium and platinum particles were not detected in the lungs of these mice. In conclusion, an electric plasma generator produced therapeutic levels of NO from air; scavenging and filtration effectively eliminated metallic impurities from the effluent gas. Copyright © 2016 Elsevier Inc. All rights reserved.

  8. Development of air conditioning technologies to reduce CO2 emissions in the commercial sector

    Science.gov (United States)

    Yoshida, Yukiko

    2006-01-01

    Background Architectural methods that take into account global environmental conservation generally concentrate on mitigating the heat load of buildings. Here, we evaluate the reduction of carbon dioxide (CO2) emissions that can be achieved by improving heating, ventilating, and air conditioning (HVAC) technologies. Results The Climate Change Research Hall (CCRH) of the National Institute for Environmental Studies (NIES) is used as a case study. CCRH was built in line with the "Green Government Buildings" program of the Government Buildings Department at the Ministry of Land, Infrastructure and Transport in Japan. We have assessed the technology used in this building, and found that there is a possibility to reduce energy consumption in the HVAC system by 30%. Conclusion Saving energy reduces CO2 emissions in the commercial sector, although emission factors depend on the country or region. Consequently, energy savings potential may serve as a criterion in selecting HVAC technologies with respect to emission reduction targets. PMID:17062161

  9. Development of air conditioning technologies to reduce CO2 emissions in the commercial sector

    Directory of Open Access Journals (Sweden)

    Yoshida Yukiko

    2006-10-01

    Full Text Available Abstract Background Architectural methods that take into account global environmental conservation generally concentrate on mitigating the heat load of buildings. Here, we evaluate the reduction of carbon dioxide (CO2 emissions that can be achieved by improving heating, ventilating, and air conditioning (HVAC technologies. Results The Climate Change Research Hall (CCRH of the National Institute for Environmental Studies (NIES is used as a case study. CCRH was built in line with the "Green Government Buildings" program of the Government Buildings Department at the Ministry of Land, Infrastructure and Transport in Japan. We have assessed the technology used in this building, and found that there is a possibility to reduce energy consumption in the HVAC system by 30%. Conclusion Saving energy reduces CO2 emissions in the commercial sector, although emission factors depend on the country or region. Consequently, energy savings potential may serve as a criterion in selecting HVAC technologies with respect to emission reduction targets.

  10. Development of air conditioning technologies to reduce CO2 emissions in the commercial sector.

    Science.gov (United States)

    Yoshida, Yukiko

    2006-10-25

    Architectural methods that take into account global environmental conservation generally concentrate on mitigating the heat load of buildings. Here, we evaluate the reduction of carbon dioxide (CO2) emissions that can be achieved by improving heating, ventilating, and air conditioning (HVAC) technologies. The Climate Change Research Hall (CCRH) of the National Institute for Environmental Studies (NIES) is used as a case study. CCRH was built in line with the "Green Government Buildings" program of the Government Buildings Department at the Ministry of Land, Infrastructure and Transport in Japan. We have assessed the technology used in this building, and found that there is a possibility to reduce energy consumption in the HVAC system by 30%. Saving energy reduces CO2 emissions in the commercial sector, although emission factors depend on the country or region. Consequently, energy savings potential may serve as a criterion in selecting HVAC technologies with respect to emission reduction targets.

  11. Secondary Organic Aerosol Formation from Ambient Air in an Oxidation Flow Reactor at GoAmazon2014/5

    Science.gov (United States)

    Palm, Brett B.; de Sa, Suzane S.; Campuzano-Jost, Pedro; Day, Douglas A.; Hu, Weiwei; Seco, Roger; Park, Jeong-Hoo; Guenther, Alex; Kim, Saewung; Brito, Joel; Wurm, Florian; Artaxo, Paulo; Yee, Lindsay; Isaacman-VanWertz, Gabrial; Goldstein, Allen; Newburn, Matt K.; Lizabeth Alexander, M.; Martin, Scot T.; Brune, William H.; Jimenez, Jose L.

    2016-04-01

    During GoAmazon2014/5, ambient air was exposed to controlled concentrations of OH or O3 in situ using an oxidation flow reactor (OFR). Oxidation ranged from hours-several weeks of aging. Oxidized air was sampled by several instruments (e.g., HR-AMS, ACSM, PTR-TOF-MS, SMPS, CCN) at both the T3 site (IOP1: Feb 1-Mar 31, 2014, and IOP2: Aug 15-Oct 15, 2014) and T2 site (between IOPs and into 2nd IOP). The oxidation of ambient air in the OFR led to substantial and variable secondary organic aerosol (SOA) formation from any SOA-precursor gases, known and unknown, that entered the OFR. In general, more SOA was produced during the nighttime than daytime, suggesting that SOA-precursor gases were found in relatively higher concentrations at night. Similarly, more SOA was formed in the dry season (IOP2) than wet season (IOP1). The maximum amount of SOA produced during nighttime from OH oxidation ranged from less than 1 μg/m3 on some nights to greater than 10 μg/m3 on other nights. O3 oxidation of ambient air also led to SOA formation, although several times less than from OH oxidation. The amount of SOA formation sometimes, but not always, correlated with measured gas-phase biogenic and/or anthropogenic SOA precursors (e.g., SV-TAG sesquiterpenes, PTR-TOFMS aromatics, isoprene, and monoterpenes). The SOA mass formed in the OFR from OH oxidation was up to an order of magnitude larger than could be explained from aerosol yields of measured primary VOCs. This along with measurements from previous campaigns suggests that most SOA was formed from intermediate S/IVOC sources (e.g., VOC oxidation products, evaporated POA, or direct emissions). To verify the SOA yields of VOCs under OFR experimental conditions, atmospherically-relevant concentrations of several VOCs were added individually into ambient air in the OFR and oxidized by OH or O3. SOA yields in the OFR were similar to published chamber yields. Preliminary PMF factor analysis showed production of secondary factors in

  12. FINAL REPORT on Experimental Validation of Stratified Flow Phenomena, Graphite Oxidation, and Mitigation Strategies of Air Ingress Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Chang H. Oh; Eung S. Kim; Hee C. NO; Nam Z. Cho

    2011-01-01

    The U.S. Department of Energy is performing research and development that focuses on key phenomena that are important during challenging scenarios that may occur in the Next Generation Nuclear Plant (NGNP)/Generation IV very high temperature reactor (VHTR). Phenomena Identification and Ranking studies to date have identified the air ingress event, following on the heels of a VHTR depressurization, as very important. Consequently, the development of advanced air ingress-related models and verification & validation are of very high priority for the NGNP Project. Following a loss of coolant and system depressurization incident, air ingress will occur through the break, leading to oxidation of the in-core graphite structure and fuel. This study indicates that depending on the location and the size of the pipe break, the air ingress phenomena are different. In an effort to estimate the proper safety margin, experimental data and tools, including accurate multidimensional thermal-hydraulic and reactor physics models, a burn-off model, and a fracture model are required. It will also require effective strategies to mitigate the effects of oxidation, eventually. This 3-year project (FY 2008–FY 2010) is focused on various issues related to the VHTR air-ingress accident, including (a) analytical and experimental study of air ingress caused by density-driven, stratified, countercurrent flow, (b) advanced graphite oxidation experiments, (c) experimental study of burn-off in the core bottom structures, (d) structural tests of the oxidized core bottom structures, (e) implementation of advanced models developed during the previous tasks into the GAMMA code, (f) full air ingress and oxidation mitigation analyses, (g) development of core neutronic models, (h) coupling of the core neutronic and thermal hydraulic models, and (i) verification and validation of the coupled models.

  13. Intelligence on the second stage. 'Air-On' plus air/water heat pump. Cheap air conditioning technology; Intelligenz der zweiten Stufe. 'Air-On' plus Luft/Wasser-Waermepumpe. Preiswerte Raumklimatechnik

    Energy Technology Data Exchange (ETDEWEB)

    Genath, Bernd

    2011-07-15

    It is hard to believe: The heating technique still holds thoughtful surprises. Based on the idea and based on the physics of the heating technology, the company Air-On AG (Cham, Switzerland). For the renovation of old buildings, this company used a second stage of a heat pump to replace old heaters. This second stage is a Peltier element and exclusively tempers a individual room decentrally. The second stage has a better coefficiency of performance than the first stage such as an air / water heat pump.

  14. Benchmarking, Research, Development, and Support for ORNL Automated Image and Signature Retrieval (AIR/ASR) Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, K.W.

    2004-06-01

    This report describes the results of a Cooperative Research and Development Agreement (CRADA) with Applied Materials, Inc. (AMAT) of Santa Clara, California. This project encompassed the continued development and integration of the ORNL Automated Image Retrieval (AIR) technology, and an extension of the technology denoted Automated Signature Retrieval (ASR), and other related technologies with the Defect Source Identification (DSI) software system that was under development by AMAT at the time this work was performed. In the semiconductor manufacturing environment, defect imagery is used to diagnose problems in the manufacturing line, train yield management engineers, and examine historical data for trends. Image management in semiconductor data systems is a growing cause of concern in the industry as fabricators are now collecting up to 20,000 images each week. In response to this concern, researchers at the Oak Ridge National Laboratory (ORNL) developed a semiconductor-specific content-based image retrieval method and system, also known as AIR. The system uses an image-based query-by-example method to locate and retrieve similar imagery from a database of digital imagery using visual image characteristics. The query method is based on a unique architecture that takes advantage of the statistical, morphological, and structural characteristics of image data, generated by inspection equipment in industrial applications. The system improves the manufacturing process by allowing rapid access to historical records of similar events so that errant process equipment can be isolated and corrective actions can be quickly taken to improve yield. The combined ORNL and AMAT technology is referred to hereafter as DSI-AIR and DSI-ASR.

  15. Amorphous Bimetallic Oxide-Graphene Hybrids as Bifunctional Oxygen Electrocatalysts for Rechargeable Zn-Air Batteries.

    Science.gov (United States)

    Wei, Li; Karahan, H Enis; Zhai, Shengli; Liu, Hongwei; Chen, Xuncai; Zhou, Zheng; Lei, Yaojie; Liu, Zongwen; Chen, Yuan

    2017-10-01

    Metal oxides of earth-abundant elements are promising electrocatalysts to overcome the sluggish oxygen evolution and oxygen reduction reaction (OER/ORR) in many electrochemical energy-conversion devices. However, it is difficult to control their catalytic activity precisely. Here, a general three-stage synthesis strategy is described to produce a family of hybrid materials comprising amorphous bimetallic oxide nanoparticles anchored on N-doped reduced graphene oxide with simultaneous control of nanoparticle elemental composition, size, and crystallinity. Amorphous Fe0.5 Co0.5 Ox is obtained from Prussian blue analog nanocrystals, showing excellent OER activity with a Tafel slope of 30.1 mV dec(-1) and an overpotential of 257 mV for 10 mA cm(-2) and superior ORR activity with a large limiting current density of -5.25 mA cm(-2) at 0.6 V. A fabricated Zn-air battery delivers a specific capacity of 756 mA h gZn(-1) (corresponding to an energy density of 904 W h kgZn(-1) ), a peak power density of 86 mW cm(-2) and can be cycled over 120 h at 10 mA cm(-2) . Other two amorphous bimetallic, Ni0.4 Fe0.6 Ox and Ni0.33 Co0.67 Ox , are also produced to demonstrate the general applicability of this method for synthesizing binary metal oxides with controllable structures as electrocatalysts for energy conversion. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Synthesis of ozone from air via a polymer-electrolyte-membrane cell with a doped tin oxide anode

    OpenAIRE

    Wang, YH; Cheng, S; Chan, KY

    2006-01-01

    The generation of ozone from air using an electrochemical cell consisting of an air cathode, a polymer-electrolyte-membrane (PEM), and a doped tin oxide anode is reported. This synthesis is environmentally friendly compared to the conventional high-voltage corona discharge process since NOx formation is eliminated; a higher ozone concentration is generated; and lower energy may be required. © The Royal Society of Chemistry 2006.

  17. Role of Bismuth Oxide in Bi-MCo2O4(M=Co,Ni,Cu,Zn) Catalysts for Wet Air Oxidation of Acetic Acid

    Institute of Scientific and Technical Information of China (English)

    JIANG Peng-bo; CHENG Tie-xin; ZHUANG Hong; CUI Xiang-hao; BI Ying-li; ZHEN Kai-ji

    2004-01-01

    Two series of cobalt(Ⅲ)-containing spinel catalysts were prepared by the decomposition of the corresponding nitrates. The catalysts doped with bismuth oxide exhibit a higher activity in the wet air oxidation of acetic acid than those without dopant bismuth oxide. The catalysts were investigated by XRD, TEM, ESR, UV-DRS and XPS, and the interaction between Co and Bi was studied as well. It has been found that nano-sized bismuth oxide is paved on the surface of cobalt spinel crystal and the structures of cobalt(Ⅲ)-containing spinel are still maintained. The shift of the binding energy of Bi4f7/2 is related to the catalytic activity of these catalysts doped with bismuth oxide.

  18. Oxidation rate of nuclear-grade graphite IG-110 in the kinetic regime for VHTR air ingress accident scenarios

    Science.gov (United States)

    Lee, Jo Jo; Ghosh, Tushar K.; Loyalka, Sudarshan K.

    2014-03-01

    The oxidation rates of nuclear-grade graphite IG-110 in the kinetically-controlled temperature regime of graphite oxidation were predicted and compared in Very High Temperature Reactor air ingress accident scenarios. The oxidative mass loss of graphite was measured thermogravimetrically from 873 to 1873 K in 100% air (21 mol%). The activation energy was found to be 222.07 kJ/mol, and the order of reaction with respect to oxygen concentration is 0.76. The surfaces of the samples were characterized by Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Fourier Transform Infrared Spectroscopy and X-ray Photoelectron Spectroscopy before and after oxidation. These results are compared with those available in the literature, and our recently reported results for NBG-18 nuclear-grade graphite using the same technique.

  19. Innovative pollution prevention program at Air Force owned Raytheon operated facility incorporating Russian technology

    Energy Technology Data Exchange (ETDEWEB)

    Stallings, J.H.; Cepeda-Calderon, S.

    1999-07-01

    Air Force Plant 44 in Tucson, Arizona is owned by the Air Force and operated by Raytheon Missile Systems Company. A joint Air Force/Raytheon Pollution Prevention Team operates at AFP 44 with the ultimate goal to minimize or eliminate the use of hazardous substances. The team works together to uncover new technologies and methods that will replace chemicals used in the plant's missile manufacturing facilities. The program maximizes pollution prevention by first eliminating hazardous material use, then chemical recycling, next hazardous waste reduction and finally wastewater treatment and recycling. From fiscal years 1994 through 1997, nine pollution prevention projects have been implemented, totaling $2.6 million, with a payback averaging less than two years. A unique wastewater treatment method has been demonstrated as part of this program. This is electroflotation, a Russian technology which removes dispersed particles from liquid with gas bubbles obtained during water electrolysis. A unit was built in the US which successfully removed organic emulsions from wastewater. Operational units are planned for the removal of waste from waterfall paint booths. The pollution prevention joint team continues to be very active with two projects underway in FY 98 and two more funded for FY 99.

  20. Oxidation behavior of in-situ Al2O3/TiAl composites at 900℃ in static air

    Institute of Scientific and Technical Information of China (English)

    Tao-tao Ai; Fen Wang; Xiao-ming Feng

    2009-01-01

    In-situ Al2O3/TiAl composites were successfully synthesized from the starting powders of Ti, Al, TiO2 and Nb2O5. The oxidation behavior of the composites at 900℃ in static air was investigated. The results indicate that the composite samples present a much lower oxidation mass gain. Under long-time intensive oxidation exposure, the formed oxide scale is multi-layer. The formation of the outer TiO2 layer is fine and dense, the internal Al2O3 scale has good adhesiveness with the outer TiO2 scale, and the TiO2+Al2O3 mixed layer forming the protective oxide scale is favorable for the improvement of oxidation resistance. It is believed that the incorporation of Al2O3 particulates into the metal matrix decreases the coefficient of thermal expansion of the substrate, and forms a local three-dimensional network structure that can hold the oxide scale. The formation of the oxide scale with fmer particle size, stronger adherence, less micro-defects and slower growth rate can contribute to the improvement of oxidation resistance. Nb element plays an important role in reducing the internal oxidation action of the materials, restraining the growth of TiO2 crystals andpromoting thc stable formation of the Al 2O3-riched layer,which is benfeicial to improve the oxidation properties.

  1. Integration of CO2 air capture and solid oxide electrolysis for methane production

    DEFF Research Database (Denmark)

    Ebbehøj, Søren Lyng

    This work studied the production of substitute natural gas (SNG) from CO2 captured from the atmosphere followed by co-electrolysis with H2O in solid oxide electrolyzer cells (SOEC) and downstream catalytic methane production.Over the coming 20 years, Denmark is on a track to remove fossil fuels...... are projected to be used for production of process heat, peak-load power generation and on the longer term to replace hydrocarbons in the most energy intensive parts of the transportation sector; especially aviation. As a prerequisite for the scenario, no biomass can be imported to enhance the supply...... of combustible resources. In such an energy system, technologies for production of CO2 neutral hydrocarbons for easy storage and use in the existing infrastructure; especially in the natural gas grid; may be of great value. The studied technology fulfills those demands.The main goal of the work was to design...

  2. Influence of the different oxidation treatment on the performance of multi-walled carbon nanotubes in the catalytic wet air oxidation of phenol.

    Science.gov (United States)

    Yang, Shaoxia; Wang, Xingang; Yang, Hongwei; Sun, Yu; Liu, Yunxia

    2012-09-30

    Multi-walled carbon nanotubes (MWCNTs) functionalized by different oxidants (HNO(3)/H(2)SO(4), H(2)O(2), O(3) and air) have been used as catalysts for the wet air oxidation of phenol. To investigate the effect of the oxidation conditions on the structure of the functionalized MWCNTs, various characterization techniques, e.g., scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, Fourier-transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) have been used. The MWCNTs treated with O(3) and H(2)O(2) show higher amounts of oxygen-containing functional groups and carboxylic acid groups, and a weaker acidic nature, in comparison with those treated with other oxidizing agents. All the functionalized MWCNTs exhibit good activity in the catalytic wet air oxidation (CWAO) of phenol. However, the MWCNTs treated with O(3) show the highest activity with desirable stability in comparison with other functionalized MWCNTs, indicating that the functionalization of carbon nanotubes with O(3) is a very promising strategy in synthesizing efficient catalysts for CWAO.

  3. Microbial methane oxidation processes and technologies for mitigation of landfill gas emissions

    DEFF Research Database (Denmark)

    Scheutz, Charlotte; Kjeldsen, Peter; Bogner, J.E.;

    2009-01-01

    utilizing oxygen that diffuses into the cover layer from the atmosphere. The methane oxidation process, which is governed by several environmental factors, can be exploited in engineered systems developed for methane emission mitigation. Mathematical models that account for methane oxidation can be used...... to predict methane emissions from landfills. Additional research and technology development is needed before methane mitigation technologies utilizing microbial methane oxidation processes can become commercially viable and widely deployed.......Landfill gas containing methane is produced by anaerobic degradation of organic waste. Methane is a strong greenhouse gas and landfills are one of the major anthropogenic sources of atmospheric methane. Landfill methane may be oxidized by methanotrophic microorganisms in soils or waste materials...

  4. Key Technology and Experimental Results of the Clean Air Heated Facility for Supersonic Combustion

    Institute of Scientific and Technical Information of China (English)

    ZHONG Zipeng; SONG Wenyan; LE Jialing

    2009-01-01

    The scramjet, which is the propulsion of hypersonic vehicle, has become the focus in many military developed countries. The ground tests play an important role in the research of scramjet. There is defect of test medium contamination (the thermochemical characteristic of the ground test medium is different from that of the flight medium) in existing ground test facilities for scramjet combustor experiment. To solve the problem of test medium contamination, the first clean air heated facility of China for scramjet combustor experiment is designed. The key technology of designing the clean air heated facility is summarized. By using bypass duct, combustor model is protected from high temperature. To reduce the switching time between main duct and bypass duct, solenoid valve and water-cooled system were used. Having centrosymmetric structure, the heat radiating area of the facility and heat loss of the facility are much lower than others. Clean air heated facility is adopted to conduct experiment, which is the first experiment of China in clean air inflow, research on hydrogen-fueled and ethylene-fueled ignition and combustion for scramjet combustor at different equivalence ratio. Successful ignition and sustained combustion of hydrogen has been achieved. Successful ethylene ignition and sustained main stream combustion is achieved with normal fuel injection and taking hydrogen as pilot flame. Experiment result shows that the wall pressure of combustor model rises when the equivalence ratio of hydrogen rises. As the wall pressure of combustor model rises, the pressure disturbance influences the shock train in the upstream.

  5. Modelling of Zry-4 cladding oxidation by air, under severe accident conditions using the MAAP4 code

    Energy Technology Data Exchange (ETDEWEB)

    Beuzet, Emilie, E-mail: emilie.beuzet@edf.f [EDF R and D, 1 Avenue du General de Gaulle, F-92140 Clamart (France); Lamy, Jean-Sylvestre, E-mail: jean-sylvestre.lamy@edf.f [EDF R and D, 1 Avenue du General de Gaulle, F-92140 Clamart (France); Bretault, Armelle, E-mail: armelle.bretault@edf.f [EDF R and D, 1 Avenue du General de Gaulle, F-92140 Clamart (France); Simoni, Eric, E-mail: simoni@ipno.in2p3.f [Institut de Physique Nucleaire, Universite Paris Sud XI, F-91406 Orsay (France)

    2011-04-15

    In a nuclear power plant, a potential risk in some low probability situations in severe accidents is air ingress into the vessel. Air is a highly oxidizing atmosphere that can lead to an enhanced core oxidation and degradation affecting the release of Fission Products (FP), especially increasing that of ruthenium. This FP is of particular importance because of its high radio-toxicity and its ability to form highly volatile oxides. Oxygen affinity is decreasing between Zircaloy cladding, fuel and ruthenium inclusions in the fuel. It is consequently of great need to understand the phenomena governing cladding oxidation by air as a prerequisite for the source term issues. A review of existing data in the field of Zircaloy-4 oxidation in air-containing atmosphere shows that this phenomenon is quantitatively well understood. The cladding oxidation process can be divided into two kinetic regimes separated by a breakaway transition. Before transition, a protective dense zirconia scale grows following a solid state diffusion-limited regime for which experimental data are well fitted by a parabolic time dependence. For a given thickness, which depends mainly on temperature and the extent of pre-oxidation in steam, the dense scale can potentially breakdown. In case of breakaway combined with oxygen starvation, cladding oxidation can then be much faster because of the combined action of oxygen and nitrogen through a complex self sustaining nitriding-oxidation process. A review of the pre-existing correlations used to simulate zirconia scale growth under air atmospheres shows a high degree of variation from parabolic to accelerated time dependence. Variations also exist in the choice of the breakaway parameter based on zirconia phase change or oxide thickness. Several correlations and breakaway parameters found in the literature were implemented in the MAAP4.07 Severe Accident code. They were assessed by simulation of the QUENCH-10 test, which is a semi-integral test designed

  6. Tension-Compression Fatigue of an Oxide/Oxide Ceramic Matrix Composite at Elevated Temperature in Air and Steam Environments

    Science.gov (United States)

    2015-03-26

    than several other advanced aerospace materials [15]. It is these qualities that make ceramics candidate materials for advanced aerospace ...TENSION-COMPRESSION FATIGUE OF AN OXIDE/OXIDE CERAMIC MATRIX COMPOSITE AT ELEVATED TEMPERATURE IN...is not subject to copyright protection in the United States. AFIT-ENY-MS-15-M-222 TENSION-COMPRESSION FATIGUE OF AN OXIDE/OXIDE CERAMIC MATRIX

  7. Wear and friction of oxidation-resistant mechanical carbon graphites at 650 C in air

    Science.gov (United States)

    Allen, G. P.; Wisnader, D. W.

    1975-01-01

    Studies were conducted to determine the friction and wear properties of experimental carbon-graphites. Hemispherically tipped carbon-graphite rider specimens were tested in sliding contact with rotating Inconel X-750 disks in air. A surface speed of 1.33 m/sec, a load of 500 g, and a specimen temperature of 650 C were used. Results indicate: (1) hardness is not a major factor in determining friction and wear under the conditions of these studies. (2) Friction and wear as low as or lower than those observed for a good commercial seal material were attained with some of the experimental materials studied. (3) The inclusion of boron carbide (as an oxidation inhibitor) has a strong influence on wear rate. (4) Phosphate treatment reduces the friction coefficient when boron carbide is not present in the base material.

  8. Clean air. Measures against fine dust and nitrogen oxide; Luftreinhalteplanung. Massnahmen gegen Feinstaub und Stickstoffoxide

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-10-15

    Within the meeting of the Bavarian State Ministry of the Environment (Hof, Federal Republic of Germany) on 23rd October, 2012, the following lectures were held: (1) Future development of emissions and immission in Germany (Johanna Appelhans); (2) Air pollution control in urban areas - Example Stuttgart (Ulrich Reuter); (3) Green zones in Munich and Augsburg - Results from the efficiency analysis 2012 (Manfred Ertl); (4) Photocatalytic efficiency of titanium dioxide - Pilot experiment Fulda (Marita Mang); (5) Emission behaviour of Euro V/5 and VI/6 vehicles in real operation (Stefan Hausberger); (6) Reduction of particles and NO{sub x} by means of Euro VI commercial vehicles (Stefan Kamm); (7) Possibilities of retrofitting at vehicles for the reduction of emissions of fine dust and nitrous oxides (Michael Himmen); (8) Measures for reduction of emissions at construction machinery (Hinrich Helms); (9) ChimCat/circledR - Catalytic reduction of emissions (Martin Pley); (10) Improvement of the immission behaviour at the Airport Munich (Hermann Blomeyer).

  9. Adiabatic Gasification and Pyrolysis of Coffee Husk Using Air-Steam for Partial Oxidation

    Directory of Open Access Journals (Sweden)

    Catalina Rodriguez

    2011-01-01

    Full Text Available Colombian coffee industry produces about 0.6 million tons of husk (CH per year which could serve as feedstock for thermal gasification to produce gaseous and liquid fuels. The current paper deals with: (i CH adiabatic gasification modeling using air-steam blends for partial oxidation and (ii experimental thermogravimetric analysis to determine the CH activation energy (E. The Chemical Equilibrium with Applications Program (CEA, developed by NASA, was used to estimate the effect of equivalence ratio (ER and steam to fuel ratio (S : F on equilibrium temperature and gas composition of ~150 species. Also, an atom balance model was developed for comparison purposes. The results showed that increased ER and (S : F ratios produce mixtures that are rich in H2 and CO2 but poor in CO. The value for the activation energy was estimated to be 221 kJ/kmol.

  10. Controllable Impregnation Via Inkjet Printing for the Fabrication of Solid Oxide Cell Air Electrodes

    KAUST Repository

    Da'as, E. H.

    2013-10-07

    The impregnation method has been considered as one of the most successful techniques for the fabrication of highly efficient electrodes for solid oxide fuel and electrolysis cells (SOCs) at the lab scale. However, because the impregnation is usually performed manually, its irreproducibility remains a major problem that can be solved by using controllable techniques, such as inkjet printing. In this paper, lanthanum strontium manganite (LSM)/yttria stabilized zirconia (YSZ) air electrodes were prepared by infiltrating YSZ porous bodies with LSM precursor solution using inkjet printing, followed by annealing at 800°C for 2 hours. XRD analysis confirmed the formation of the LSM phase, which was in the form of nanoparticles with size in the 50-70 nm range on the YSZ walls, as revealed by FEG-SEM observations. The effect of printing parameters on the distribution of the impregnated phase was investigated and discussed.

  11. Graphene oxide membranes with high permeability and selectivity for dehumidification of air

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Yongsoon; Liu, Wei; Schwenzer, Birgit; Manandhar, Sandeep; Chase-Woods, Dylan G.; Engelhard, Mark H.; Devanathan, Ram; Fifield, Leonard S.; Bennett, Wendy D.; Ginovska-Pangovska, Bojana; Gotthold, David W.

    2016-09-01

    Hierarchically stacked 2D graphene oxide (GO) membranes are a fascinating and promising new class of materials with the potential for radically improved water vapor/gas separation with excellent selectivity and high permeability. This paper details dehumidification results from flowing gas mixtures through free-standing GO membrane samples prepared by a casting method. The first demonstrated use of free-standing GO membranes for water vapor separation reveals outstanding water vapor permeability and H2O/N2 selectivity. Free-standing GO membranes exhibit extremely high water vapor permeability of 1.82 x 105 Barrer and a water vapor permeance of 1.01 x 10-5 mol/m2sPa, while the nitrogen permeability was below the system’s detection limit, yielding a selectivity >104 in 80% relative humidity (RH) air at 30.8 °C. The results show great potential for a range of energy conversion and environmental applications

  12. The NASA Lightning Nitrogen Oxides Model (LNOM): Application to Air Quality Modeling

    Science.gov (United States)

    Koshak, William; Peterson, Harold; Khan, Maudood; Biazar, Arastoo; Wang, Lihua

    2011-01-01

    Recent improvements to the NASA Marshall Space Flight Center Lightning Nitrogen Oxides Model (LNOM) and its application to the Community Multiscale Air Quality (CMAQ) modeling system are discussed. The LNOM analyzes Lightning Mapping Array (LMA) and National Lightning Detection Network(TradeMark)(NLDN) data to estimate the raw (i.e., unmixed and otherwise environmentally unmodified) vertical profile of lightning NO(x) (= NO + NO2). The latest LNOM estimates of lightning channel length distributions, lightning 1-m segment altitude distributions, and the vertical profile of lightning NO(x) are presented. The primary improvement to the LNOM is the inclusion of non-return stroke lightning NOx production due to: (1) hot core stepped and dart leaders, (2) stepped leader corona sheath, K-changes, continuing currents, and M-components. The impact of including LNOM-estimates of lightning NO(x) for an August 2006 run of CMAQ is discussed.

  13. Flexible high power-per-weight perovskite solar cells with chromium oxide-metal contacts for improved stability in air

    Science.gov (United States)

    Kaltenbrunner, Martin; Adam, Getachew; Głowacki, Eric Daniel; Drack, Michael; Schwödiauer, Reinhard; Leonat, Lucia; Apaydin, Dogukan Hazar; Groiss, Heiko; Scharber, Markus Clark; White, Matthew Schuette; Sariciftci, Niyazi Serdar; Bauer, Siegfried

    2015-10-01

    Photovoltaic technology requires light-absorbing materials that are highly efficient, lightweight, low cost and stable during operation. Organolead halide perovskites constitute a highly promising class of materials, but suffer limited stability under ambient conditions without heavy and costly encapsulation. Here, we report ultrathin (3 μm), highly flexible perovskite solar cells with stabilized 12% efficiency and a power-per-weight as high as 23 W g-1. To facilitate air-stable operation, we introduce a chromium oxide-chromium interlayer that effectively protects the metal top contacts from reactions with the perovskite. The use of a transparent polymer electrode treated with dimethylsulphoxide as the bottom layer allows the deposition--from solution at low temperature--of pinhole-free perovskite films at high yield on arbitrary substrates, including thin plastic foils. These ultra-lightweight solar cells are successfully used to power aviation models. Potential future applications include unmanned aerial vehicles--from airplanes to quadcopters and weather balloons--for environmental and industrial monitoring, rescue and emergency response, and tactical security applications.

  14. Leaf photosynthetic and water-relations responses for 'Valencia' orange trees exposed to oxidant air pollution

    Energy Technology Data Exchange (ETDEWEB)

    Olszyk, D.M.; Takemoto, B.K.; Poe, M.

    1991-01-01

    Leaf responses were measured to test a hypothesis that reduced photosynthetic capacity and/or altered water relations were associated with reductions in yield for 'Valencia' orange trees (Citrus sinensis (L.), Osbeck) exposed to ambient oxidant air pollution. Exposures were continuous for 4 years to three levels of oxidants (in charcoal-filtered, half-filtered, and non-filtered air). Oxidants had no effect on net leaf photosynthetic rates or on photosynthetic pigment concentrations. A single set of measurements indicated that oxidants increased leaf starch concentrations (24%) prior to flowering, suggesting a change in photosynthate allocation. Leaves exposed to oxidants had small, but consistent, changes in water relations over the summer growing season, compared to trees growing in filtered air. Other changes included decreased stomatal conductance (12%) and transpiration (9%) rates, and increased water pressure potentials (5%). While all responses were subtle, their cumulative impact over 4 years indicated that 'Valencia' orange trees were subject to increased ambient oxidant stress.

  15. Thai - new air injection technology for heavy oil recovery and in situ upgrading

    Energy Technology Data Exchange (ETDEWEB)

    Greaves, M.; El-Sakr, A.; Xia, T.X. [Bath Univ. (United Kingdom); Ayasse, C.; Turta, A. [Petroleum Recovery Inst., Calgary, AB (Canada)

    1999-11-01

    A new enhanced oil recovery process called THAI (Toe-to-Heel Air Injection) was presented. THAI is a gravity assisted process that is controlled by the pressure gradient established between a draining reservoir section and inflow to a horizontal producer well. The process, which integrates advanced technology and horizontal well concepts, achieves excellent recovery rates for heavy oil. THAI can also realize substantial in situ upgrading by thermal cracking, producing upgraded oil to the surface. In the THAI process, a horizontal producer well is positioned in a line drive in the reservoir and air is injected via a horizontal injection well. The process restricts drainage to a narrow mobile zone which makes it possible for mobilized fluids to enter directly into the exposed section of a horizontal production well. THAI can be used in primarily production, as a new technology, as a follow-up to existing technologies, or as a co-process where thermal efficiency is needed. The process was tested on `Forties Mix` oil, Clair, West of Shetlands medium heavy oil and heavy Wolf Lake oil. It was demonstrated that the most important part of the process is the creation of the narrow mobile oil zone ahead of the combustion front. The width of the zone depends on reservoir conditions and the degree to which the cold oil seals the horizontal producer well. Oil recovery rates in the tests were found to be as high as 85 per cent OOIP. 12 refs., 6 tabs.

  16. Silent Discharge Plasma Technology for the Treatment of Air Toxics and Other Applications

    Energy Technology Data Exchange (ETDEWEB)

    Rosocha, Louis A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chase, Peter J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gross, Michael P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    1998-09-21

    Under this CRADA, the Los Alamos National Laboratory (LANL) and High Mesa Technologies, Inc. (HMT) carried out a joint project on the development of the silent discharge plasma (SDP) technology for the treatment of hazardous air pollutants and other hazardous or toxic chemicals. The project had two major components: a technology-demonstration part and a scale-up and commercialization part. In the first part, a small-scale, mobile SDP plasma processor, which was being developed under a CRADA with the Electric Power Research Institute (EPRI) was the mobile equipment was modified for higher capacity service and employed for an innovative remediation technologies demonstration on soil-vapor extraction off-gases at the McClellan Air Force Base near Sacramento, CA. The performance of the SDP system for the variety of volatile organic compounds (VOCs) encountered at the McClellan site was sufficiently promising to the project HMT and LANL worked together to formulate a scale-up strategy and commercialization/manufacturing plan, and to design a prototype scaled-up SDP unit. HMT and LANL are now in the final stages of completing a licensing agreement for the technology and HMT is in the process of raising funds to engineer and manufacture commercial prototype SDP equipment focused on stack-gas emissions control and environmental remediation. HMT, in collaboration with another Northern New Mexico business, Coyote Aerospace, has also been successful in receiving a Phase I Small Business Innovative Research (SBIR) award from the Army Research Office to develop, design, and construct a small non-thermal plasma reactor for laboratory studies ("Non-Thermal Plasma Reactor for Control of Fugitive Emissions of Toxic Gases")

  17. Kinetics of Air Oxidation and Oxygen Oxidation of Paraffin%石蜡氧气氧化和空气氧化动力学

    Institute of Scientific and Technical Information of China (English)

    方静; 杨基和; 刘英杰

    2011-01-01

    The esterification wax was synthesized by one-step oxygen oxidation and esterification process from mixed paraffin and microcrystalline with the mass ratio of 6:4. The results were compared with traditional air oxidation process. The kinetic models of the oxygen and air oxidation were established, respectively. The model parameters were obtained by linear regression of saponification values under different reaction temperatures The activation energy is 6.49 kJ/mol for oxygen oxidation and 11.56 KJ/mol for air oxidaomtion, while pre-exponent factor is 3.09 h-1 and 11.33 h-1, respectively. Compared with air oxidation, the product of oxygen oxidation possesses higher esterification number, less off-gas discharge and quicker reaction rate.%石蜡与微晶蜡质量比6∶4的混合原料,经纯氧氧化、酯化一步法合成高酯值蜡.与传统的空气氧化法进行了对比研究,并以皂化值为参数建立了两种氧化法的动力学模型.由不同反应温度下的实验数据回归得到氧气氧化反应的活化能为6.49 kJ/mol,指前因子为3.09h-1;空气氧化反应的活化能为11.56 kJ/mol,指前因子为11.33 h-1.研究表明,相对于空气氧化法,氧气氧化法具有产品酯化值高、尾气排放量少以及反应速率快的优点

  18. Selective oxidation with nanoporous silica supported sensitizers: An environment friendly process using air and visible light

    Energy Technology Data Exchange (ETDEWEB)

    Saint-Cricq, Philippe; Pigot, Thierry; Blanc, Sylvie [Institut des Sciences Analytiques et de Physicochimie pour l' Environnement et les Materiaux, Universite de Pau et des Pays de l' Adour, Helioparc-2 Av. du President Angot, F-64053 Pau Cedex 09 (France); Lacombe, Sylvie, E-mail: sylvie.lacombe@univ-pau.fr [Institut des Sciences Analytiques et de Physicochimie pour l' Environnement et les Materiaux, Universite de Pau et des Pays de l' Adour, Helioparc-2 Av. du President Angot, F-64053 Pau Cedex 09 (France)

    2012-04-15

    Highlights: Black-Right-Pointing-Pointer Photo-sensitizers were covalently grafted on silica matrices. Black-Right-Pointing-Pointer Grafted powdered silica was characterized by diffuse reflectance and emission spectroscopy. Black-Right-Pointing-Pointer Selective solvent-free photo-oxygenation was carried out with air under visible light. Black-Right-Pointing-Pointer Singlet generation and reactivity at the gas-solid interface was demonstrated. - Abstract: Transparent and porous silica xerogels containing various grafted photosensitizers (PSs) such as anthraquinone derivatives, Neutral Red, Acridine Yellow and a laboratory-made dicyano aromatics (DBTP) were prepared. In most cases, the xerogels were shown to be mainly microporous by porosimetry. The PSs were characterized in the powdered monoliths (form, aggregation, concentration) by electronic spectroscopy which also proved to be a useful tool for monitoring the material evolution after irradiation. These nanoporous xerogels were used as microreactors for gas/solid solvent-free photo-oxygenation of dimethylsulfide (DMS) using visible light and air as the sole reactant. All these PSs containing monoliths were efficient for gas-solid DMS oxidation, leading to sulfoxide and sulfone in varying ratios. As these polar oxidation products remained strongly adsorbed on the silica matrix, the gaseous flow at the outlet of the reactor was totally free of sulfide and odorless. The best results in term of yield and initial rate of degradation of DMS were obtained with DBTP containing xerogels. Moreover, as these materials were reusable without loss of efficiency and sensitizer photobleaching after a washing regeneration step, the concept of recyclable sensitizing materials was approved, opening the way to green process.

  19. Degradation of phenylamine by catalytic wet air oxidation using metal catalysts with modified supports.

    Science.gov (United States)

    Torrellas, Silvia A; Escudero, Gabriel O; Rodriguez, Araceli R; Rodriguez, Juan G

    2015-01-01

    The effect of acid treatments with HCl and HNO3 on the surface area and surface chemistry of three granular activated carbons was studied. These supports were characterized and the hydrochloric acid treatment leads to the best activated carbon support (AC2-C). The catalytic behavior of Pt, Ru and Fe (1 wt.%) supported on granular activated carbon treated with HCl was tested in the phenylamine continuous catalytic wet air oxidation in a three-phase, high-pressure catalytic reactor over a range of reaction temperatures 130-170ºC and total pressure of 1.0-3.0 MPa at LHSV = 0.4-1 h(-1), whereas the phenylamine concentration range and the catalyst loading were 5-16 mol.m(-3) and 0.5-1.5 g, respectively. Activity as well as conversion varied as a function of the metal, the catalyst preparation method and operation conditions. Higher activities were obtained with Pt incorporated on hydrochloric acid -treated activated carbon by the ion exchange method. In steady state, approximately 98% phenylamine conversion, 77% of TOC and 94% of COD removal, was recorded at 150ºC, 11 mol m(-3) of phenylamine concentration and 1.5 g of catalyst, and the selectivity to non-organic compounds was 78%. Several reaction intermediaries were detected. A Langmuir-Hinshelwood model gave an excellent fit of the kinetic data of phenylamine continuous catalytic wet air oxidation over the catalysts of this work.

  20. Directions in US Air Force space power technology for global virtual presence

    Science.gov (United States)

    Keener, David; Reinhardt, Kitt; Mayberry, Clay; Radzykewycz, Dan; Donet, Chuck; Marvin, Dean; Hill, Carole

    1998-01-01

    Recent trends in the development of high efficiency, light-weight, compact, reliable and cost-effective space power technologies needed to support the development of next-generation military and commercial satellites will be discussed. Development of new light-weight and reduced volume electrical power system (EPS) technologies are required to enable the design of future ``smallsats'' with power requirements less than 1500W, to ``monstersats'' having projected power levels ranging from 10-50kW for commercial communication and military space based radar type satellites. In support of these projected requirements a complement of power generation, power management and distribution, and energy storage technologies are under development at the Air Force Research Laboratory's Space Vehicles Directorate. The technologies presented in this paper include high efficiency multijunction solar cells, alkali metal thermal electric converters (AMTEC), high-voltage (70-130V)/high-efficiency/high-density power management and distribution (PMAD) electronics, and high energy density electrochemical and mechanical energy storage systems (sodium sulfur, lithium-ion, and flywheels). Development issues and impacts of individual technologies will be discussed in context with global presence satellite mission requirements.

  1. The application of advanced oxidation technologies to the treatment of effluents from the pulp and paper industry: a review.

    Science.gov (United States)

    Hermosilla, Daphne; Merayo, Noemí; Gascó, Antonio; Blanco, Ángeles

    2015-01-01

    The paper industry is adopting zero liquid effluent technologies to reduce freshwater use and meet environmental regulations, which implies closure of water circuits and the progressive accumulation of pollutants that must be removed before water reuse and final wastewater discharge. The traditional water treatment technologies that are used in paper mills (such as dissolved air flotation or biological treatment) are not able to remove recalcitrant contaminants. Therefore, advanced water treatment technologies, such as advanced oxidation processes (AOPs), are being included in industrial wastewater treatment chains aiming to either improve water biodegradability or its final quality. A comprehensive review of the current state of the art regarding the use of AOPs for the treatment of the organic load of effluents from the paper industry is herein addressed considering mature and emerging treatments for a sustainable water use in this sector. Wastewater composition, which is highly dependent on the raw materials being used in the mills, the selected AOP itself, and its combination with other technologies, will determine the viability of the treatment. In general, all AOPs have been reported to achieve good organic removal efficiencies (COD removal >40%, and about an extra 20% if AOPs are combined with biological stages). Particularly, ozonation has been the most extensively reported and successfully implemented AOP at an industrial scale for effluent treatment or reuse within pulp and paper mills, although Fenton processes (photo-Fenton particularly) have actually addressed better oxidative results (COD removal ≈ 65-75%) at a lab scale, but still need further development at a large scale.

  2. Disrupted Nitric Oxide Metabolism from Type II Diabetes and Acute Exposure to Particulate Air Pollution.

    Directory of Open Access Journals (Sweden)

    Ashley P Pettit

    Full Text Available Type II diabetes is an established cause of vascular impairment. Particulate air pollution is known to exacerbate cardiovascular and respiratory conditions, particularly in susceptible populations. This study set out to determine the impact of exposure to traffic pollution, with and without particle filtration, on vascular endothelial function in Type II diabetes. Endothelial production of nitric oxide (NO has previously been linked to vascular health. Reactive hyperemia induces a significant increase in plasma nitrite, the proximal metabolite of NO, in healthy subjects, while diabetics have a lower and more variable level of response. Twenty type II diabetics and 20 controls (ages 46-70 years were taken on a 1.5 hr roadway traffic air pollution exposure as passengers. We analyzed plasma nitrite, as a measure of vascular function, using forearm ischemia to elicit a reactive hyperemic response before and after exposure to one ride with and one without filtration of the particle components of pollution. Control subjects displayed a significant increase in plasma nitrite levels during reactive hyperemia. This response was no longer present following exposure to traffic air pollution, but did not vary with whether or not the particle phase was filtered out. Diabetics did not display an increase in nitrite levels following reactive hyperemia. This response was not altered following pollution exposure. These data suggest that components of acute traffic pollution exposure diminish vascular reactivity in non-diabetic individuals. It also confirms that type II diabetics have a preexisting diminished ability to appropriately respond to a vascular challenge, and that traffic pollution exposure does not cause a further measureable acute change in plasma nitrite levels in Type II diabetics.

  3. Catalytic Wet Air Oxidation of Oxalic Acid using Platinum Catalysts in Bubble Column Reactor: A Review

    Directory of Open Access Journals (Sweden)

    A. K. Saroha

    2010-01-01

    Full Text Available Wastewater treatment and re-use of industrial process water are critical issue for the development of human activities andenvironment conservation. Catalytic wet air oxidation (CWAO is an attractive and useful technique for treatment of effluentswhere the concentrations of organic pollutants are too low, for the incineration and other pollution control techniquesto be economically feasible and when biological treatments are ineffective, e.g. in the case of toxic effluents. In CWAO,combustion takes place on a Pt/Al2O3 catalysts usually at temperatures several degrees below those required forthermal incineration. In CWAO process, the organic contaminants dissolved in water are either partially degraded by meansof an oxidizing agent into biodegradable intermediates or mineralized into innocuous inorganic compounds such as CO2,H2O and inorganic salts, which remain in the aqueous phase. In contrast to other thermal processes CWAO produces no NOx,SO2, HCl, dioxins, furans, fly ash, etc. This review paper presents the application of platinum catalysts in bubble columnreactor for CWAO of oxalic acid.

  4. Catalytic wet air oxidation of 2-chlorophenol over sewage sludge-derived carbon-based catalysts.

    Science.gov (United States)

    Tu, Yuting; Xiong, Ya; Tian, Shuanghong; Kong, Lingjun; Descorme, Claude

    2014-07-15

    A sewage sludge derived carbon-supported iron oxide catalyst (FeSC) was prepared and used in the Catalytic Wet Air Oxidation (CWAO) of 2-chlorophenol (2-CP). The catalysts were characterized in terms of elemental composition, surface area, pHPZC, XRD and SEM. The performances of the FeSC catalyst in the CWAO of 2-CP was assessed in a batch reactor operated at 120°C under 0.9MPa oxygen partial pressure. Complete decomposition of 2-CP was achieved within 5h and 90% Total Organic Carbon (TOC) was removed after 24h of reaction. Quite a straight correlation was observed between the 2-CP conversion, the amount of iron leached in solution and the pH of the reaction mixture at a given reaction time, indicating a strong predominance of the homogeneous catalysis contribution. The iron leaching could be efficiently prevented when the pH of the solution was maintained at values higher than 4.5, while the catalytic activity was only slightly reduced. Upon four successive batch CWAO experiments, using the same FeSC catalyst recovered by filtration after pH adjustment, only a very minor catalyst deactivation was observed. Finally, based on all the identified intermediates, a simplified reaction pathway was proposed for the CWAO of 2-CP over the FeSC catalyst.

  5. Ruthenium versus platinum on cerium materials in wet air oxidation of acetic acid

    Energy Technology Data Exchange (ETDEWEB)

    Gaalova, J. [Institute of Chemical Process Fundamentals of the CAS, Rozvojova 135, 165 02 Prague 6, CZ (Czech Republic); Barbier, J., E-mail: Jacques.barbier.jr@univ-poitiers.fr [University of Poitiers, LACCO UMR 6503, Laboratoire de Catalyse par les Metaux, 40 Avenue du Recteur Pineau, F-86022 POITIERS Cedex (France); Rossignol, S. [University of Limoges, ENSCI, 47 Avenue Albert Thomas 87000 Limoges France (France)

    2010-09-15

    This study was a comparison between Ru-catalysts and similar, previously investigated, Pt-catalysts. In this paper, ruthenium catalysts for catalytic wet air oxidation are prepared, characterized and tested. Both catalysts were supported on commercial CeO{sub 2} as well as mixed oxide Zr{sub 0.1}(Ce{sub 0.75}Pr{sub 0.25}){sub 0.9}O{sub 2}. The catalysts were characterized by measuring the oxygen storage capacities (OSC), BET, XRD, FTIR and chemisorption of hydrogen. In addition, the effect of sintering (treatments under H{sub 2}) was compared with both of the catalysts. The comparison of the results showed that initial intrinsic activity of ruthenium is not significantly influenced by the type of the support, which is contrast to platinum. Furthermore, the particle size of Ru had an important effect on CWAO activity: the higher the particle size, the better the activity. This was different with Pt-catalysts, where the optimal particle size was smaller, having about 15% of metal dispersion.

  6. Air pollution: what matters most? : Physical, chemical and oxidative properties of air pollution components related to toxic effects

    NARCIS (Netherlands)

    Steenhof, M.

    2015-01-01

    Numerous studies have been published on the adverse health effects associated with both short- and long-term exposure to air pollution. Air pollution is a heterogeneous, complex mixture of gases, liquids, and particulate matter (PM). Up to now, PM mass concentration has been the metric of choice to

  7. MHD air heater technology development. Annual technical progress report, January 1, 1980-December 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-03-01

    Progress on the technology development of the directly-fired high temperature air heater (HTAH) for MHD power plants is described in detail. The objective of task 1 is to continue development of ceramic materials technology for the directly-fired HTAH. The objectives of task 2 are to demonstrate the technical feasibility of operating a directly-fired HTAH (including both the heater matrix and valves), to continue obtaining information on life and corrosion resistance of HTAH materials, and to obtain design information for full-scale studies and future design work. The objectives of task 3 are to begin the identification of HTAH control requirements and control system needs, and to continue full-scale study efforts incorporating updated materials and design information in order to identify development needs for the HTAH development program. (WHK)

  8. Coupled Physical/Chemical and Biofiltration Technologies to Reduce Air Emissions from Forest Products Industries

    Energy Technology Data Exchange (ETDEWEB)

    Gary D. McGinnis

    2001-12-31

    The research is a laboratory and bench-scale investigation of a system to concentrate and destroy volatile organic compounds (VOCs), including hazardous air pollutants, formed from the drying of wood and the manufacture of wood board products (e.g., particle board and oriented strandboard). The approach that was investigated involved concentrating the dilute VOCs (<500 ppmv) with a physical/chemical adsorption unit, followed by the treatment of the concentrated voc stream (2,000 to 2,500 ppmv) with a biofiltration unit. The research program lasted three years, and involved three research organizations. Michigan Technological University was the primary recipient of the financial assistance, the USDA Forest Products Laboratory (FPL) and Mississippi State University (MSU) were subcontractors to MTU. The ultimate objective of this research was to develop a pilot-scale demonstration of the technology with sufficient data to provide for the design of an industrial system. No commercialization activities were included in this project.

  9. Better-Than-Visual Technologies for Next Generation Air Transportation System Terminal Maneuvering Area Operations

    Science.gov (United States)

    Prinzel, Lawrence J., III; Bailey, Randall E.; Shelton, Kevin J.; Jones, Denise R.; Kramer, Lynda J.; Arthur, Jarvis J., III; Williams, Steve P.; Barmore, Bryan E.; Ellis, Kyle E.; Rehfeld, Sherri A.

    2011-01-01

    A consortium of industry, academia and government agencies are devising new concepts for future U.S. aviation operations under the Next Generation Air Transportation System (NextGen). Many key capabilities are being identified to enable NextGen, including the concept of Equivalent Visual Operations (EVO) replicating the capacity and safety of today's visual flight rules (VFR) in all-weather conditions. NASA is striving to develop the technologies and knowledge to enable EVO and to extend EVO towards a Better-Than-Visual (BTV) operational concept. The BTV operational concept uses an electronic means to provide sufficient visual references of the external world and other required flight references on flight deck displays that enable VFR-like operational tempos and maintain and improve the safety of VFR while using VFR-like procedures in all-weather conditions. NASA Langley Research Center (LaRC) research on technologies to enable the concept of BTV is described.

  10. What Is Happening when the Blue Bottle Bleaches: An Investigation of the Methylene Blue-Catalyzed Air Oxidation of Glucose

    Science.gov (United States)

    Anderson, Laurens; Wittkopp, Stacy M.; Painter, Christopher J.; Liegel, Jessica J.; Schreiner, Rodney; Bell, Jerry A.; Shakhashiri, Bassam Z.

    2012-01-01

    An investigation of the Blue Bottle Experiment, a well-known lecture demonstration reaction involving the dye-catalyzed air oxidation of a reducing sugar in alkaline solution, has delineated the sequence of reactions leading to the bleaching of the dye, the regeneration of color, and so forth. Enolization of the sugar is proposed as a key step in…

  11. What Is Happening when the Blue Bottle Bleaches: An Investigation of the Methylene Blue-Catalyzed Air Oxidation of Glucose

    Science.gov (United States)

    Anderson, Laurens; Wittkopp, Stacy M.; Painter, Christopher J.; Liegel, Jessica J.; Schreiner, Rodney; Bell, Jerry A.; Shakhashiri, Bassam Z.

    2012-01-01

    An investigation of the Blue Bottle Experiment, a well-known lecture demonstration reaction involving the dye-catalyzed air oxidation of a reducing sugar in alkaline solution, has delineated the sequence of reactions leading to the bleaching of the dye, the regeneration of color, and so forth. Enolization of the sugar is proposed as a key step in…

  12. Interior microelectrolysis oxidation of polyester wastewater and its treatment technology.

    Science.gov (United States)

    Yang, Xiaoyi

    2009-09-30

    This paper has investigated the effects of interior microelectrolysis pretreatment on polyester wastewater treatment and analyzed its mechanism on COD and surfactant removal. The efficiency of interior microelectrolysis is mainly influenced by solution pH, aeration and reaction time. Contaminants can be removed not only by redox reaction and flocculation in the result of ferrous and ferric hydroxides but also by electrophoresis under electric fields created by electron flow. pH confirms the chemical states of surfactants, Fe(II)/Fe(III) ratio and the redox potential, and thus influences the effects of electrophoresis, flocculation and redox action on contaminant removal. Anaerobic and aerobic batch tests were performed to study the degradation of polyester wastewater. The results imply that interior microelectrolysis and anaerobic pretreatment are lacking of effectiveness if applied individually in treating polyester wastewater in spite of their individual advantages. The interior microelectrolysis-anaerobic-aerobic process was investigated to treat polyester wastewater with comparison with interior microelectrolysis-aerobic process and anaerobic-aerobic process. High COD removal efficiencies have been gotten by the combination of interior microelectrolysis with anaerobic technology and aerobic technology. The results also imply that only biological treatment was less effective in polyester wastewater treatment.

  13. Oxidation Behavior of Germanium- and/or Silicon-Bearing Near-α Titanium Alloys in Air

    Science.gov (United States)

    Kitashima, Tomonori; Yamabe-Mitarai, Yoko

    2015-06-01

    The effect of germanium (Ge) and/or silicon (Si) addition on the oxidation behavior of the near-α alloy Ti-5Al-2Sn-4Zr-2Mo was investigated in air at 973 K (700 °C). Ge addition decreased the oxidation resistance because of the formation of a Ge-rich layer in the substrate at the TiO2/substrate interface, enhancing Sn segregation at the interface. In addition, a small amount of Ge dissolved in the external Al2O3 layer. These results reduced the aluminum activity at the interface, suppressed the formation of Al2O3, and increased the diffusivity of oxygen in the oxide scales. The addition of 0.2 and 0.9 wt pct Si was beneficial for improving oxidation resistance. The effect of germanide and silicide precipitates in the matrix on the oxide growth process was also discussed.

  14. Air Traffic Management Technology Demonstration-1 Concept of Operations (ATD-1 ConOps), Version 3.0

    Science.gov (United States)

    Baxley, Brian T.; Johnson, William C.; Scardina, John; Shay, Richard F.

    2016-01-01

    This document describes the goals, benefits, technologies, and procedures of the Concept of Operations (ConOps) for the Air Traffic Management (ATM) Technology Demonstration #1 (ATD-1), and provides an update to the previous versions of the document [ref 1 and ref 2].

  15. Wet air oxidation as a pretreatment option for selective biodegradability enhancement and biogas generation potential from complex effluent.

    Science.gov (United States)

    Padoley, K V; Tembhekar, P D; Saratchandra, T; Pandit, A B; Pandey, R A; Mudliar, S N

    2012-09-01

    This study looks at the possibility of wet air oxidation (WAO) based pretreatment of complex effluent to selectively enhance the biodegradability (without substantial COD destruction) and facilitate biogas generation potential. A lab-scale wet air oxidation reactor with biomethanated distillery wastewater (B-DWW) as a model complex effluent (COD 40,000 mg L(-1)) was used to demonstrate the proof-of-concept. The studies were conducted using a designed set of experiments and reaction temperature (150-200°C), air pressure (6-12 bar) and reaction time (15-120 min) were the main process variables of concern for WAO process optimization. WAO pretreatment of B-DWW enhanced the biodegradability of the complex wastewater by the virtue of enhancing its biodegradability index (BI) from 0.2 to 0.88, which indicate favorable Biochemical Methane Potential (BMP) for biogas generation. The kinetics of COD destruction and BI enhancement has also been reported.

  16. Preparation, certification and interlaboratory analysis of workplace air filters spiked with high-fired beryllium oxide.

    Science.gov (United States)

    Oatts, Thomas J; Hicks, Cheryl E; Adams, Amy R; Brisson, Michael J; Youmans-McDonald, Linda D; Hoover, Mark D; Ashley, Kevin

    2012-02-01

    Occupational sampling and analysis for multiple elements is generally approached using various approved methods from authoritative government sources such as the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA), as well as consensus standards bodies such as ASTM International. The constituents of a sample can exist as unidentified compounds requiring sample preparation to be chosen appropriately, as in the case of beryllium in the form of beryllium oxide (BeO). An interlaboratory study was performed to collect analytical data from volunteer laboratories to examine the effectiveness of methods currently in use for preparation and analysis of samples containing calcined BeO powder. NIST SRM(®) 1877 high-fired BeO powder (1100 to 1200 °C calcining temperature; count median primary particle diameter 0.12 μm) was used to spike air filter media as a representative form of beryllium particulate matter present in workplace sampling that is known to be resistant to dissolution. The BeO powder standard reference material was gravimetrically prepared in a suspension and deposited onto 37 mm mixed cellulose ester air filters at five different levels between 0.5 μg and 25 μg of Be (as BeO). Sample sets consisting of five BeO-spiked filters (in duplicate) and two blank filters, for a total of twelve unique air filter samples per set, were submitted as blind samples to each of 27 participating laboratories. Participants were instructed to follow their current process for sample preparation and utilize their normal analytical methods for processing samples containing substances of this nature. Laboratories using more than one sample preparation and analysis method were provided with more than one sample set. Results from 34 data sets ultimately received from the 27 volunteer laboratories were subjected to applicable statistical analyses. The observed

  17. Treating leachate mixture with anaerobic ammonium oxidation technology

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong-guo; ZHOU Shao-qi

    2006-01-01

    Large amounts of ammonium and a low content of biodegradable chemical oxygen demand(COD) are contained in leachate from aged landfills, together with the effluent containing high concentration of nitric nitrogen after biochemical treatment.Treatment effect of anaerobic ammonium oxidation (anammox) process on the mixture of the leachate and its biochemical effluent was investigated. The results show that the average removal efficiencies of ammonium, nitric nitrogen and total nitrogen are 87.51%,74.95% and 79.59%, respectively, corresponding to the average ratio of removed nitric nitrogen to ammonium, i.e. 1.14 during the steady phase of anammox activity. The mean removal efficiency of COD is only 24.01% during the experimental period. The demand of total phosphorous for the anammox process is unobvious. Especially, the alkalinity and pH value of the effluent are close to those of the influent during the steady phase of anammox activity. In addition, it is demonstrated that the status of the anammox bioreactor can be indicated by the alkalinity and pH value during the course of the experiment. The anammox bioreactor has shown potential for nitrogen removal in the leachate mixture. However, COD and total phosphorous in the leachate mixture need further treatment for removal efficiencies of COD and total phosphorous are not good in the anammox bioreactor.

  18. Evolutionary Agent-Based Simulation of the Introduction of New Technologies in Air Traffic Management

    Science.gov (United States)

    Yliniemi, Logan; Agogino, Adrian K.; Tumer, Kagan

    2014-01-01

    Accurate simulation of the effects of integrating new technologies into a complex system is critical to the modernization of our antiquated air traffic system, where there exist many layers of interacting procedures, controls, and automation all designed to cooperate with human operators. Additions of even simple new technologies may result in unexpected emergent behavior due to complex human/ machine interactions. One approach is to create high-fidelity human models coming from the field of human factors that can simulate a rich set of behaviors. However, such models are difficult to produce, especially to show unexpected emergent behavior coming from many human operators interacting simultaneously within a complex system. Instead of engineering complex human models, we directly model the emergent behavior by evolving goal directed agents, representing human users. Using evolution we can predict how the agent representing the human user reacts given his/her goals. In this paradigm, each autonomous agent in a system pursues individual goals, and the behavior of the system emerges from the interactions, foreseen or unforeseen, between the agents/actors. We show that this method reflects the integration of new technologies in a historical case, and apply the same methodology for a possible future technology.

  19. Directions in US Air Force space power energy generation and distribution technology

    Science.gov (United States)

    Reinhardt, Kitt; Keener, Dave; Schuller, Mike

    1997-01-01

    Recent trends in the development of high efficiency, light-weight, reliable and cost-effective space power technologies needed to support the development of near-term, next-generation government and commercial satellites will be discussed. Significant advancements in light-weight and reduced volume electrical power system (EPS) components are required to enable the design of future smallsats with power requirements of less than 1000 W to monster-sats having projected power demands ranging from 10-50 kW for civilian and military communications and space based radar needs. For these missions increased emphasis is placed on reducing total satellite mass to enable use of smaller, less costly, and easier to deploy launch vehicles. In support of these requirements a complement of power generation, power management and distribution, and energy storage technologies are under development at the Air Force Phillips Laboratory Space and Missiles Technology Directorate. Specific technologies presented in this paper include high efficiency multijunction solar cells, low-cost thin-film solar cells, ultra light-weight flexible solar arrays, solar electric thermal converters, and high-voltage (70-130 V) and high-efficiency power management and distribution (PMAD) electronics. The projected impact of EPS subsystem performance on existing, near-term, and next-generation 10-50 kW military satellites will be discussed, along with technical issues and status of EPS component development.

  20. Creep behavior of alloy 617 in high temperature air and helium environments-effect of oxidation damage

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Chang Heui; Kim, Sung Hwan [Dept. of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Sah, Injin; Kim, Dae Jong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    The creep behavior of a nickel-base superalloy, Alloy 617, which is considered as a candidate material for the very high temperature gas cooled reactor, was studied. Creep rupture tests were carried out at 800°C, 900°C and 1000°C in static and flowing helium environments as well as in air. Creep rupture life in static helium was longer than that in air, while it was shorter in flowing helium environments. Microstructure observation of the creep tested specimens showed that the shorter creep rupture life in flowing helium was associated with the thicker oxide layer, greater decarburization depth, and deeper internal oxidation happened during the creep tests. The degree of such oxidation damage was quantified for the creep tested specimens and correlated with the creep rupture life in different environments.

  1. Practical advanced oxidation processes for waste water treatment:I. the principle, characteristic, advantage and disadvantage of various advanced oxidation technologies%废水处理的实用高级氧化技术第一部分──各类高级氧化技术的原理、特性和优缺点

    Institute of Scientific and Technical Information of China (English)

    方景礼

    2014-01-01

    评述了芬顿氧化法、催化臭氧氧化法、光催化氧化法、电解催化氧化法、湿式空气氧化/湿式催化氧化法、超临界水氧化法、超声氧化法等各类目前认为最有实用价值的高级氧化技术的原理、特性和各自的优缺点,分析了各类高级氧化技术存在的问题和未来的发展趋势。认为金属催化臭氧氧化技术结合了臭氧氧化力强和金属催化剂易于制造、经久耐用、不需另加其他药剂和操作成本低的优点,是既经济又高效的氧化技术,也是未来较有发展前途的技术。%The principles, characteristics, advantages, and disadvantages of the various most practical advanced oxidation technologies recently, for example, Fenton oxidation, catalytic ozone oxidation, photocatalytic oxidation, electrolytic catalytic oxidation, wet air oxidation and catalytic wet air oxidation, supercritical water oxidation, and supersonic oxidation, were reviewed and the problems existing in various advanced oxidation technologies and the development tendency in the further were analyzed. It is considered that the metal-catalyzed ozone oxidation is an economic and highly efficient oxidation technology combining the advantages of both ozone’s strong oxidation ability and metal catalyzer’ easy manufacturing, high durability, no need of adding other reagents, and low operation cost, showing a good development prospect in the future.

  2. Total reflection X-ray fluorescence trace mercury determination by trapping complexation: Application in advanced oxidation technologies

    Energy Technology Data Exchange (ETDEWEB)

    Custo, Graciela [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); Litter, Marta I. [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina); Escuela de Posgrado, Universidad de General San Martin, San Lorenzo 3391 Villa Ballester, 1653. Prov. de Buenos Aires (Argentina); Rodriguez, Diana [Universidad Nacional de Lujan, Ruta 5 y 7. Prov. de Buenos Aires (Argentina); Vazquez, Cristina [Unidad de Actividad Quimica, Comision Nacional de Energia Atomica, Av. Gral Paz 1499 (B1650KNA) San Martin, Buenos Aires (Argentina) and Laboratorio de Quimica de Sistemas Heterogeneos, Facultad de Ingenieria, Universidad de Buenos Aires, P. Colon 850 (C1063ACU), Buenos Aires (Argentina)]. E-mail: Cristina.Vazquez@cnea.gov.ar

    2006-11-15

    It is well known that Hg species cause high noxious effects on the health of living organisms even at very low levels (5 {mu}g/L). Quantification of this element is an analytical challenge due to the peculiar physicochemical properties of all Hg species. The regulation of the maximal allowable Hg concentration led to search for sensitive methods for its determination. Total reflection X-ray fluorescence is a proved instrumental analytical tool for the determination of trace elements. In this work, the use of total reflection X-ray fluorescence for Hg quantification is investigated. However, experimental determination by total reflection X-ray fluorescence requires depositing a small volume of sample on the reflector and evaporation of the solvent until dryness to form a thin film. Because of volatilization of several Hg forms, a procedure to capture these volatile species in liquid samples by using complexing agents is proposed. Acetate, oxalic acid, ethylenediaminetetracetic acid and ammonium pyrrolidine-dithiocarbamate were assayed for trapping the analytes into the solution during the preparation of the sample and onto the reflector during total reflection X-ray fluorescence measurements. The proposed method was applied to evaluate Hg concentration during TiO{sub 2}-heterogeneous photocatalysis, one of the most known advanced oxidation technologies. Advanced oxidation technologies are processes for the treatment of effluents in waters and air that involve the generation of very active oxidative and reductive species. In heterogeneous photocatalysis, Hg is transformed to several species under ultraviolet illumination in the presence of titanium dioxide. Total reflection X-ray fluorescence was demonstrated to be applicable in following the extent of the heterogeneous photocatalysis reaction by determining non-transformed Hg in the remaining solution.

  3. Total reflection X-ray fluorescence trace mercury determination by trapping complexation: Application in advanced oxidation technologies

    Science.gov (United States)

    Custo, Graciela; Litter, Marta I.; Rodríguez, Diana; Vázquez, Cristina

    2006-11-01

    It is well known that Hg species cause high noxious effects on the health of living organisms even at very low levels (5 μg/L). Quantification of this element is an analytical challenge due to the peculiar physicochemical properties of all Hg species. The regulation of the maximal allowable Hg concentration led to search for sensitive methods for its determination. Total reflection X-ray fluorescence is a proved instrumental analytical tool for the determination of trace elements. In this work, the use of total reflection X-ray fluorescence for Hg quantification is investigated. However, experimental determination by total reflection X-ray fluorescence requires depositing a small volume of sample on the reflector and evaporation of the solvent until dryness to form a thin film. Because of volatilization of several Hg forms, a procedure to capture these volatile species in liquid samples by using complexing agents is proposed. Acetate, oxalic acid, ethylenediaminetetracetic acid and ammonium pyrrolidine-dithiocarbamate were assayed for trapping the analytes into the solution during the preparation of the sample and onto the reflector during total reflection X-ray fluorescence measurements. The proposed method was applied to evaluate Hg concentration during TiO 2-heterogeneous photocatalysis, one of the most known advanced oxidation technologies. Advanced oxidation technologies are processes for the treatment of effluents in waters and air that involve the generation of very active oxidative and reductive species. In heterogeneous photocatalysis, Hg is transformed to several species under ultraviolet illumination in the presence of titanium dioxide. Total reflection X-ray fluorescence was demonstrated to be applicable in following the extent of the heterogeneous photocatalysis reaction by determining non-transformed Hg in the remaining solution.

  4. Silicon-technology based microreactors for high-temperature heterogeneous partial oxidation reactions

    NARCIS (Netherlands)

    Tiggelaar, Roald Michel

    2004-01-01

    In this thesis the results of a study into the feasibility of silicon-technology based microreactors for fast oxidation reactions have been discussed. When designed properly, silicon microreactors are suitable for studying heterogeneous gas phase reactions, such as reaction kinetics of direct cataly

  5. PROFILE: Potential for Advanced Technology to Improve Air Quality and Human Health in Shanghai.

    Science.gov (United States)

    STREETS; HEDAYAT; CARMICHAEL; ARNDT; CARTER

    1999-04-01

    / Air quality in most Asian cities is poor and getting worse. It will soon become impossible to sustain population, economic, and industrial growth without severe deterioration of the atmospheric environment. This paper addresses the city of Shanghai, the air-quality problems it faces over the next 30 years, and the potential of advanced technology to alleviate these problems. Population, energy consumption, and emission profiles are developed for the city at 0.1 degrees x 0.1 degrees resolution and extrapolated from 1990 to 2020 using sector-specific economic growth factors. Within the context of the RAINS-Asia model, eight technology scenarios are examined for their effects on ambient concentrations of sulfur dioxide and sulfate and their emission control costs. Without new control measures, it is projected that the number of people exposed to sulfur dioxide concentrations in excess of guidelines established by the World Health Organization will rise from 650,000 in 1990 to more than 14 million in 2020. It is apparent that efforts to reduce emissions are likely to have significant health benefits, measured in terms of the cost of reducing the number of people exposed to concentrations in excess of the guidelines ($10-50 annually per person protected). Focusing efforts on the control of new coal-fired power plants and industrial facilities has the greatest benefit. However, none of the scenarios examined is alone capable of arresting the increases in emissions, concentrations, and population exposure. It is concluded that combinations of stringent scenarios in several sectors will be necessary to stabilize the situation, at a potential cost of $500 million annually by the year 2020. KEY WORDS: Coal; China; Shanghai; Sulfur dioxide; Air quality; Health effects

  6. Relevance of PCDD/PCDF formation for the evaluation of POPs destruction technologies. PCB destruction by super critical water oxidation (SCWO)

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R. [Tuebingen Univ. (Germany)

    2004-09-15

    Supercritical water oxidation (SCWO) is one technology listed from United Nations Industrial Development Organization (UNIDO) as ''Emerging and Innovative Technologies'' and from United Nations Environmental Programme (UNEP) as ''Commercialized Technology with Considerable Experience''. In laboratory experiments and pilot plants it has been shown that PCBs can be destroyed by sub- and super-critical water oxidation. In these studies it was not examined or reported if the formation of PCDFs occured during the PCB destruction. PCBs exhibit a special challenge because they are PCDF precursors and can be easily oxidized into the more toxic PCDFs. Therefore, during thermal treatment of PCBs, the formation of PCDFs has to be considered, in particular for oxidative destruction technologies. Only Hatakeda et al. reported the detection of toxicologically non-relevant monochlorinated dibenzofurans as byproducts during SCWO of 3-monochlorobiphenyl. However, during all thermal treatments of PCBs, the formation of PCDFs, especially the toxic 2,3,7,8-substituted congeners (TEQ), has to be considered as an important parameter and closely evaluated when establishing a treatment method for PCB destruction. It has been shown that the oxidation of PCB to PCDF occurs in the presence of air already at temperature as low as 300 C. Increasing the temperature to 550 C under short term pyrolysis conditions, conversion rates of PCB to PCDF were found to increase up to 25%. The present study evaluated the relevance of PCDF formation during SCWO of PCBs and demonstrates the importance of PCDD/PCDF monitoring for the assessment of a PCB/POP destruction technology during pilot and full-scale operations.

  7. Effects of indoor air purification by an air cleaning system (Koala technology) on semen parameters in male factor infertility: results of a pilot study.

    Science.gov (United States)

    Paradisi, R; Vanella, S; Barzanti, R; Cani, C; Battaglia, C; Seracchioli, R; Venturoli, S

    2009-06-01

    A number of studies indicated a clear decline in semen quality in the past 30-50 years and there is accumulating evidence that this decline might result from exposure to high levels of air pollution. To examine the impact of environment on male reproductive ability, we undertook for the first time a pilot study on semen quality of infertile men exposed to purification of indoor air. Ten subjects with a history of unexplained male infertility and poor semen quality were exposed for at least 1 year to a cleaning indoor air system (Koala technology). The key feature of this air purifier is the unique innovative multiple filtering system. The treatment of total purification of indoor air showed neither improvements in semen parameters nor variation in reproductive hormones (P = N.S.), but induced an evident increase (P indoor air does not seem enough to improve semen quality, although the increase in leucocytic concentrations could indicate an activation of the role of immunosurveillance in a purified indoor air environment.

  8. A Validity Study on Predictors of Success in Resident Master’s Degree Programs at the Air Force Institute of Technology.

    Science.gov (United States)

    1987-09-01

    1. 0% DEPARTMENT OF THE AIR FORCE *AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio I Dzsnm ION SATE A I A edfor ... k 6 or more examinees is a useful and valid measurement i.e., within reliability limits (10:3). The GRE and the GMAT are divided into various

  9. Diagnostic significance of nitric oxide concentrations in exhaled air from the airways in allergic rhinitis patients

    Directory of Open Access Journals (Sweden)

    Anna Kłak

    2016-05-01

    Full Text Available Introduction : The effect of nitric oxide (NO on the human body is very important due its physiological regulation of the following functions of airways: modulation of ciliary movement and maintenance of sterility in sinuses. Aim: To evaluate the diagnostic significance of NO concentrations in exhaled air from the upper and lower airways in patients diagnosed with allergic rhinitis (AR. Material and methods: The subjects included in the study were a group of 30 people diagnosed with sensitivity to environmental allergens and a control group consisting of 30 healthy subjects. The measurement of NO in the air exhaled from the lower and upper airways was performed using an on-line method by means of Restricted Exhaled Breath (REB, as well as using the measurement procedure (chemiluminescence set out in the guidelines prepared in 2005 by the American Thoracic Society and the European Respiratory Society. Results: In the late phase of the allergic reaction, higher values of the level of exhaled NO concentration from the lower airways were observed in the groups of subjects up to the threshold values of 25.17 ppb in the group of subjects with year-round allergic rhinitis and 21.78 ppb in the group with diagnosed seasonal allergic rhinitis. The difference in the concentration of NO exhaled from the lungs between the test group and the control group in the 4th h of the test was statistically significant (p = 0.045. Conclusions : Exhaled NO should be considered as a marker of airway inflammation. It plays an important role in the differential diagnosis of allergy.

  10. Thermodynamic and kinetic study of phenol degradation by a non-catalytic wet air oxidation process.

    Science.gov (United States)

    Lefèvre, Sébastien; Boutin, Olivier; Ferrasse, Jean-Henry; Malleret, Laure; Faucherand, Rémy; Viand, Alain

    2011-08-01

    This work is dedicated to an accurate evaluation of thermodynamic and kinetics aspects of phenol degradation using wet air oxidation process. Phenol is a well known polluting molecule and therefore it is important having data of its behaviour during this process. A view cell is used for the experimental study, with an internal volume of 150 mL, able to reach pressures up to 30 MPa and temperatures up to 350°C. Concerning the thermodynamic phase equilibria, experimental and modelling results are obtained for different binary systems (water/nitrogen, water/air) and ternary system (water/nitrogen/phenol). The best model is the Predictive Soave Redlich Kwong one. This information is necessary to predict the composition of the gas phase during the process. It is also important for an implementation in a process simulation. The second part is dedicated to kinetics evaluation of the degradation of phenol. Different compounds have been detected using GC coupled with a MS. A kinetic scheme is deduced, taking into account the evolution of phenol, hydroquinones, catechol, resorcinol and acetic acid. The kinetic parameters are calculated for this scheme. These data are important to evaluate the evolution of the concentration of the different polluting molecules during the process. A simplified kinetic scheme, which can be easily implemented in a process simulation, is also determined for the direct degradation of phenol into H(2)O and CO(2). The Arrhenius law data obtained for the phenol disappearance are the following: k=1.8×10(6)±3.9×10(5)M(-1)s(-1) (pre-exponential factor) and E(a)=77±8 kJ mol(-1) (activation energy).

  11. Nitric Oxide and Oxygen Air-Contamination Effects on Extinction Limits of Non-Premixed Hydrocarbon-Air Flames for a HIFiRE Scramjet

    Science.gov (United States)

    Pellett, Gerald L.; Dawson, Lucy C.; Vaden, Sarah N.; Wilson, Lloyd G.

    2009-01-01

    Unique nitric oxide (NO) and oxygen air-contamination effects on the extinction Flame Strength (FS) of non-premixed hydrocarbon (HC) vs. air flames are characterized for 7 gaseous HCs, using a new idealized 9.3 mm straight-tube Opposed Jet Burner (OJB) at 1 atm. FS represents a laminar strain-induced extinction limit based on cross-section-average air jet velocity, Uair, that sustains combustion of a counter jet of gaseous fuel just before extinction. Besides ethane, propane, butane, and propylene, the HCs include ethylene, methane, and a 64 mole-% ethylene / 36 % methane mixture, the writer s previously recommended gaseous surrogate fuel for HIFiRE scramjet tests. The HC vs. clean air part of the work is an extension of a May 2008 JANNAF paper that characterized surrogates for the HIFiRE project that should mimic the flameholding of reformed (thermally- or catalytically-cracked) endothermic JP-like fuels. The new FS data for 7 HCs vs. clean air are thus consolidated with the previously validated data, normalized to absolute (local) axial-input strain rates, and co-plotted on a dual kinetically dominated reactivity scale. Excellent agreement with the prior data is obtained for all 7 fuels. Detailed comparisons are also made with recently published (Univ. Va) numerical results for ethylene extinction. A 2009-revised ethylene kinetic model (Univ. Southern Cal) led to predicted limits within approx. 5 % (compared to 45 %, earlier) of this writer s 2008 (and present) ethylene FSs, and also with recent independent data (Univ. Va) obtained on a new OJB system. These +/- 5 % agreements, and a hoped-for "near-identically-performing" reduced kinetics model, would greatly enhance the capability for accurate numerical simulations of surrogate HC flameholding in scramjets. The measured air-contamination effects on normalized FS extinction limits are projected to assess ongoing Arc-Heater-induced "facility test effects" of NO production (e.g., 3 mole-%) and resultant oxygen

  12. Compressed air energy storage monitoring to support refrigerated mined rock cavern technology.

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Moo Yul; Bauer, Stephen J.

    2004-06-01

    This document is the final report for the Compressed Air Energy Storage Monitoring to Support Refrigerated-Mined Rock Cavern Technology (CAES Monitoring to Support RMRCT) (DE-FC26-01NT40868) project to have been conducted by CAES Development Co., along with Sandia National Laboratories. This document provides a final report covering tasks 1.0 and subtasks 2.1, 2.2, and 2.5 of task 2.0 of the Statement of Project Objectives and constitutes the final project deliverable. The proposed work was to have provided physical measurements and analyses of large-scale rock mass response to pressure cycling. The goal was to develop proof-of-concept data for a previously developed and DOE sponsored technology (RMRCT or Refrigerated-Mined Rock Cavern Technology). In the RMRCT concept, a room and pillar mine developed in rock serves as a pressure vessel. That vessel will need to contain pressure of about 1370 psi (and cycle down to 300 psi). The measurements gathered in this study would have provided a means to determine directly rock mass response during cyclic loading on the same scale, under similar pressure conditions. The CAES project has been delayed due to national economic unrest in the energy sector.

  13. MHD air heater development technology. Technical progress report, April 1, 1980-June 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-07-01

    Technology development for the directly-fired high temperature air heater (HTAH) for MHD power plants is described. Work is being done under three tasks as described in the following. (1) materials selection, evaluation, and development: The objective of this task is to continue development of ceramic materials technology for the directly-fired HTAH. The scope of the work will include compilation of materials data, materials selection for testing and design studies, materials property determination, liaison with refractory manufacturers and other organizations to encourage development of materials and fabrication technology, establishment of preliminary HTAH material specifications, analyses of test materials, and development of criteria for thermal stress limits for crack-tolerant refractory materials. (2) operability, performance, and materials testing: The objectives of this task are to demonstrate the technical feasibility of operating a directly-fired HTAH (including both the heater matrix and valves), to continue obtaining information on life and corrosion resistance of HTAH materials, and to obtain design information for full-scale studies and future design work. (3) full-scale design concepts: The objectives of this task are to begin the identification of HTAH control requirements and control system needs, and to continue full-scale study efforts incorporating updated materials and design information in order to identify development needs for the HTAH development program. Progress is described. (WHK)

  14. FY-09 Report: Experimental Validation of Stratified Flow Phenomena, Graphite Oxidation, and Mitigation Strategies of Air Ingress Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Chang H. Oh; Eung S. Kim

    2009-12-01

    The Idaho National Laboratory (INL), under the auspices of the U.S. Department of Energy, is performing research and development that focuses on key phenomena important during potential scenarios that may occur in the Next Generation Nuclear Plant (NGNP)/Gen-IV very high temperature reactor (VHTR). Phenomena Identification and Ranking Studies to date have identified that an air ingress event following on the heels of a VHTR depressurization is a very important incident. Consequently, the development of advanced air ingress-related models and verification and validation data are a very high priority for the NGNP Project. Following a loss of coolant and system depressurization incident, air will enter the core through the break, leading to oxidation of the in-core graphite structure and fuel. If this accident occurs, the oxidation will accelerate heat-up of the bottom reflector and the reactor core and will eventually cause the release of fission products. The potential collapse of the core bottom structures causing the release of CO and fission products is one of the concerns. Therefore, experimental validation with the analytical model and computational fluid dynamic (CFD) model developed in this study is very important. Estimating the proper safety margin will require experimental data and tools, including accurate multidimensional thermal-hydraulic and reactor physics models, a burn-off model, and a fracture model. It will also require effective strategies to mitigate the effects of oxidation. The results from this research will provide crucial inputs to the INL NGNP/VHTR Methods Research and Development project. The second year of this three-year project (FY-08 to FY-10) was focused on (a) the analytical, CFD, and experimental study of air ingress caused by density-driven, stratified, countercurrent flow; (b) advanced graphite oxidation experiments and modeling; (c) experimental study of burn-off in the core bottom structures, (d) implementation of advanced

  15. Enhancement of corrosion resistance for plasma nitrided AISI 4140 steel by plain air plasma post-oxidizing

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Jiqiang; Liu, Han; Ye, Xuemei [Jiangsu Key Laboratory of Materials Surface Technology, Changzhou University, Changzhou 213164 (China); Chai, Yating [Materials Research and Education Center, Auburn University, AL 36849 (United States); Hu, Jing, E-mail: jinghoo@126.com [Jiangsu Key Laboratory of Materials Surface Technology, Changzhou University, Changzhou 213164 (China); Materials Research and Education Center, Auburn University, AL 36849 (United States)

    2015-05-25

    Highlights: • Plain air was primarily used for plasma post-oxidation for AISI 4140 steel. • A thin iron oxide layer composed of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3} was formed on top of the compound layer. • The ratio of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3} was closely related to the post-oxidizing conditions. • Post-oxidizing at 673 K for 60 min brought out highest ratio of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3} and optimum corrosion resistance. - Abstract: Plasma post-oxidizing was conducted immediately after plasma nitriding in the same equipment for AISI 4140 steel, and plain air was used as the oxygen bearing gas. The cross-sectional microstructures of the treated samples were observed by optical metallography and scanning electron microcopy (SEM), and the thickness of compound layer was measured accordingly. The phases were determined by X-ray diffraction (XRD), corrosion resistance was evaluated by electrochemical polarization, and the surface morphology before and after polarization test was also observed by SEM. Meanwhile, standard Gibbs free energy of the oxidation reactions existed in Fe–O system was calculated. The results show that a thin iron oxide layer composed of magnetite (Fe{sub 3}O{sub 4}) and hematite (Fe{sub 2}O{sub 3}) is formed on top of the compound layer during plasma post-oxidizing process, and the ratio of magnetite (Fe{sub 3}O{sub 4}) to hematite (Fe{sub 2}O{sub 3}) is depended on plasma post-oxidizing temperature and time. Highest ratio of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3} is obtained while post-oxidizing at 673 K for 60 min due to lower standard Gibbs free energy and appropriate forming rate for the formation of Fe{sub 3}O{sub 4} at this temperature. The thin oxide layer brings out significant enhancement of corrosion resistance, especially at higher ratios of Fe{sub 3}O{sub 4} to Fe{sub 2}O{sub 3}, due to the dense and adherent characteristic of Fe{sub 3}O{sub 4} oxide. Surface images of the post-oxidizing specimen

  16. Supported noble metal catalysts in the catalytic wet air oxidation of industrial wastewaters and sewage sludges.

    Science.gov (United States)

    Besson, M; Descorme, C; Bernardi, M; Gallezot, P; di Gregorio, F; Grosjean, N; Minh, D Pham; Pintar, A

    2010-12-01

    This paper reviews some catalytic wet air oxidation (CWAO) investigations of industrial wastewaters over platinum and ruthenium catalysts supported on TiO2 and ZrO2 formulated to be active and resistant to leaching, with particular focus on the stability of the catalyst. Catalyst recycling experiments were performed in batch reactors and long-term stability tests were conducted in trickle-bed reactors. The catalyst did not leach upon treatment of Kraft bleaching plant and olive oil mill effluents, and could be either recycled or used for long periods of time in continuous reactors. Conversely, these catalysts were rapidly leached when used to treat effluents from the production of polymeric membranes containing N,N-dimethylformamide. The intermediate formation of amines, such as dimethylamine and methylamine with a high complexing capacity for the metal, was shown to be responsible for the metal leaching. These heterogeneous catalysts also deactivated upon CWAO of sewage sludges due to the adsorption of the solid organic matter. Pre-sonication of the sludge to disintegrate the flocs and improve solubility was inefficient.

  17. Catalytic evaluation on liquid phase oxidation of vanillyl alcohol using air and H2O2 over mesoporous Cu-Ti composite oxide

    Science.gov (United States)

    Saha, Subrata; Hamid, Sharifah Bee Abd; Ali, Tammar Hussein

    2017-02-01

    A mesoporous, highly crystalline Cu-Ti composite oxide catalyst was prepared via facile, simple and modified solution method varying Cu and Ti ratio for selective liquid phase oxidation of vanillyl alcohol. Various spectroscopic procedures were employed to systematically characterize the catalyst structural and physicochemical properties. The defect chemistry of the catalyst was confirmed from the presence of surface defects revealed through HRTEM imagery between the TiO2 (101) and Cu3TiO4 (012) planes, complemented by the XRD profiling. Further, presence of oxygen vacancy evidenced by O 1s XPS spectra were observed on the catalyst surface. Moreover, the stoichiometry of Cu and Ti in the catalyst synthesis protocol was notably found to be the vital determinant to alter the redox properties of Cu-Ti composite oxide catalyst supported by H2-TPR. O2-TPD analysis. Moreover, a rational investigation was done using different oxidants such as air and H2O2 with variables reaction conditions. The catalyst was active for liquid phase oxidation of vanillyl alcohol to vanillin with performance of 66% conversion and 71% selectivity using H2O2 in base free condition. And also, catalytic activity was significantly improved by 94% conversion with 86% selectivity to vanillin in liquid phase aerobic oxidation at the optimum reaction conditions. To expand the superiority of the catalyst, three times reusability study was also examined with appreciable catalytic activity.

  18. Laboratory study on the cooling effect of flash water evaporative cooling technology for ventilation and air-conditioning of buildings

    DEFF Research Database (Denmark)

    Fang, Lei; Yuan, Shu; Yang, Jianrong

    2016-01-01

    This paper presents a simple cooling technology using flash water evaporation. The technology combines a water atomizer with a plate heat exchanger used for heat recovery of a ventilation system. It is mainly used to cool the ventilation airflow from outdoors and is particularly suitable to be used...... in warm/hot and dry environment where dehumidification of outdoor air is not needed. A laboratory experiment was designed and conducted to evaluate the cooling effectiveness of this technology. The experiment was conducted in a twin-climate chamber. One chamber simulated warm/hot and dry outdoor...... environments and the other simulated an air-conditioned indoor environment. The flash water evaporation cooling device was installed in the chamber that simulated indoor environment. The air from the chamber simulating outdoor environment was introduced into the cooling device and cooled by the flash water...

  19. Liquid products from oxidative thermal treatment of oil sludge with different oxygen concentrations of air.

    Science.gov (United States)

    Shie, J L; Chang, C Y; Lin, J P; Le, D J; Wu, C H

    2001-01-01

    Oxidative thermal treatment of oil sludge with different oxygen concentrations of air by using a dynamic thermogravimetric (TG) reaction system is investigated. The experimental conditions employed are: gas flow rate of 50 cm3/min (value at 298 K) for 300 mg dry waste, a constant heating rate of 5.2 K/min, the oxygen concentrations in air of 1.09, 8.62 and 20.95 vol. % O2, and the temperature (T) range of 378-873 K. From the experimental results, the residual mass fractions (M) are about 78.95, 28.49, 8.77 and 4.13 wt. % at the oxidative T of 563, 713, 763 and 873 K for the case with 20.95 vol. % O2, respectively. The values of M with 8.62 and 1.09 vol. % O2 at T of 873 K are 4.87 and 9.44 wt. %, respectively. The distillation characteristics of the oil portion of liquid products (condensates of gas at 298 K) from the oxidative thermal treatment of oil sludge with 20.95 vol. % O2 at T of 378-873 K is close to those of commercial gasoline. Nevertheless, the liquid product contains a large amount of water. The distillation characteristics of the oil portions of liquid products with 8.62 and 1.09 vol. % O2 at T of 378-873 K are close to those of diesel and fuel oils, respectively. The oil quality with 8.62 vol. % O2 is better than that with 1.09 vol. % O2. However, the liquid product with 8.62 vol. % O2 still contains a large amount of water; nonetheless, that with 1.09 vol. % O2 is with negligible water. Compared with the oil product of nitrogen pyrolysis, the oil quality with 1.09 vol. % O2 is better. Certainly, low oxygen conditions (i.e. 1.09 vol. % O2) not only accelerate the thermal reaction of oil sludge, but also at the same time avoid or reduce the production of water. Further, from the analysis of benzene (B), ethylbenzene (E), toluene (T) and iso-xylene (X) concentrations of the oil portion of liquid products, the BETX concentrations of oil with 20.95 vol. % O2 are higher than those with 8.62 and 1.09 vol. % O2. The yields of liquid products with 20.95, 8

  20. Japanese power electronics inverter technology and its impact on the American air conditioning industry

    Energy Technology Data Exchange (ETDEWEB)

    Ushimaru, Kenji.

    1990-08-01

    Since 1983, technological advances and market growth of inverter- driven variable-speed heat pumps in Japan have been dramatic. The high level of market penetration was promoted by a combination of political, economic, and trade policies in Japan. A unique environment was created in which the leading domestic industries-- microprocessor manufacturing, compressors for air conditioning and refrigerators, and power electronic devices--were able to direct the development and market success of inverter-driven heat pumps. As a result, leading US variable-speed heat pump manufacturers should expect a challenge from the Japanese producers of power devices and microprocessors. Because of the vertically-integrated production structure in Japan, in contrast to the out-sourcing culture of the United States, price competition at the component level (such as inverters, sensors, and controls) may impact the structure of the industry more severely than final product sales. 54 refs., 47 figs., 1 tab.

  1. Assistive technology and passengers with special assistance needs in air transport: contributions to cabin design

    Directory of Open Access Journals (Sweden)

    Carina Campese

    2016-06-01

    Full Text Available Abstract There has been significant growth in air transport worldwide, as well as in Brazil. However, studies have emphasized that disabled, obese, and elderly passengers face difficulties when using this means of transport. Among these difficulties, issues related to passengers’ own assistive devices, including damage, loss, or the impossibility of using during the entire flight, stand out. Therefore, the present study aims to understand the trends in assistive technology focusing on cabin design. This research is based upon literature review, interviews with manufacturers and research centers, visits to specialized trade fairs, and patent search. The results revealed a great diversity of assistive products, its trends, and an increase in their use, which affect aircraft cabin design, especially in terms of space, access, and stowage of these devices.

  2. Air-Sea Exchange Of CO2: A Multi-Technology Approach

    Science.gov (United States)

    Tengberg, A.; Almroth, E.; Anderson, L.; Hall, P.; Hjalmarsson, S.; Lefevre, D.; Omstedt, A.; Rutgersson, A.; Sahlee, E.; Smedman, A.; Wesslander, K.

    2006-12-01

    We report on experiences and results from a multidisciplinary project in which we try to elucidate the complex processes involved in air-sea exchange of CO2. This study was performed in the Baltic Sea (off the Swedish island Gotland) and combined the following technologies: - Meteorological measurements of wind, turbulence, temperature, humidity, humidity flux, CO2 and CO2 flux at several levels from a fixed observation tower - Hourly PCO2 measurements with a moored automatic instrument - Collection of dissolved oxygen, temperature, salinity and turbidity data at different levels in the water column at 1-minute intervals - Daily light (PAR) and primary production measurements obtained with a moored automatic incubator - Daily primary production measurements using manual methods - Use of an acoustic current profiler to collect water column information on currents, turbulence, water level and waves - Repetitive water column profiles, from a ship, of dissolved inorganic carbon, oxygen, nutrients, alkalinity, pH, PAR, Chlorophyll A, salinity and temperature

  3. Agent Based Modeling of Air Carrier Behavior for Evaluation of Technology Equipage and Adoption

    Science.gov (United States)

    Horio, Brant M.; DeCicco, Anthony H.; Stouffer, Virginia L.; Hasan, Shahab; Rosenbaum, Rebecca L.; Smith, Jeremy C.

    2014-01-01

    As part of ongoing research, the National Aeronautics and Space Administration (NASA) and LMI developed a research framework to assist policymakers in identifying impacts on the U.S. air transportation system (ATS) of potential policies and technology related to the implementation of the Next Generation Air Transportation System (NextGen). This framework, called the Air Transportation System Evolutionary Simulation (ATS-EVOS), integrates multiple models into a single process flow to best simulate responses by U.S. commercial airlines and other ATS stakeholders to NextGen-related policies, and in turn, how those responses impact the ATS. Development of this framework required NASA and LMI to create an agent-based model of airline and passenger behavior. This Airline Evolutionary Simulation (AIRLINE-EVOS) models airline decisions about tactical airfare and schedule adjustments, and strategic decisions related to fleet assignments, market prices, and equipage. AIRLINE-EVOS models its own heterogeneous population of passenger agents that interact with airlines; this interaction allows the model to simulate the cycle of action-reaction as airlines compete with each other and engage passengers. We validated a baseline configuration of AIRLINE-EVOS against Airline Origin and Destination Survey (DB1B) data and subject matter expert opinion, and we verified the ATS-EVOS framework and agent behavior logic through scenario-based experiments. These experiments demonstrated AIRLINE-EVOS's capabilities in responding to an input price shock in fuel prices, and to equipage challenges in a series of analyses based on potential incentive policies for best equipped best served, optimal-wind routing, and traffic management initiative exemption concepts..

  4. Oxidation of metals by a plasma formed as a result of low-threshold breakdown of air

    Science.gov (United States)

    Goncharov, I. N.; Goncharov, Yu N.; Konov, Vitalii I.; Minaev, I. M.; Skvortsov, Yu A.; Chapliev, N. I.

    1981-12-01

    The characteristics of the oxidation of copper, aluminum, and titanium were determined in the case when breakdown of air was initiated by CO2 laser pulses incident on targets made of these metals. A study was made of the influence of surface oxide films on the threshold radiation intensity necessary to produce a plasma. The dependence of the efficiency of the thermal interaction of an optical-breakdown plasma on the magnitude and sign of the charge carried by the surface of a metal target was investigated for the first time in the specific case of titanium.

  5. The Histoty of Ventilation and Air Conditioning is CERN Up to Date with the latest Technological Developments?

    CERN Document Server

    Kühnl-Kinel, J

    2000-01-01

    The invention of ventilation cannot be ascribed to a certain date. It started with simple aeration when man brought fire into his abode and continued through different stages including air cooling using ice to finally arrive at the time when ventilation and air conditioning has become an essential part of our life and plays an important role in human evolution. This paper presents the history of ventilation and air conditioning, explains the key constraints over the centuries, and shows its influence on everyday life. Some examples of previous air-conditioning plants are described and different approaches to the way of calculation of ventilation systems discussed. It gives an overview of the Heating, Ventilation and Air Conditioning (HVAC) installations at CERN and points out their particularities. It also compares them with the latest technological developments in the field as well as showing the new trends that are being applied at CERN.

  6. Selection of optimized air pollutant filtration technologies for petrochemical industries through multiple-attribute decision-making.

    Science.gov (United States)

    Moridi, Parvin; Atabi, Farideh; Nouri, Jafar; Yarahmadi, Rasoul

    2017-07-15

    Selecting cost-effective and efficient air filtration technologies that ensure sustainable development is a challenge to national, regional and local policy makers. Various factors such as efficiency, maintainability, and design of the developed devices can affect the selection of optimized technologies. The present study aimed to select optimal technologies for air filtration devices in petrochemical industries through a multi-criteria decision-making (MADM) method based on a fuzzy model of Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS). Five criteria (filtration efficiency, cost, maintainability, designability, and size) were used to rank air pollution control technologies designed to eliminate particulate matter (PM), volatile organic compounds (VOCs), and ammonia (NH3). According to the results, the research criteria had different weights for different air pollutants. High-efficiency particulate air (HEPA + pre collector) filters, plasma chemistry, and chemical absorption were identified as the most appropriate filtration methods for PM, VOCs, and NH3, respectively (coefficients = 0.923, 0.9586, and 0.867, respectively). Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Field demonstration and commercialization of silent discharge plasma hazardous air pollutant control technology

    Energy Technology Data Exchange (ETDEWEB)

    Rosocha, L.A.; Coogan, J.J.; Korzekwa, R.A.; Secker, D.A. [Los Alamos National Lab., NM (United States); Reimers, R.F.; Herrmann, P.G.; Chase, P.J.; Gross, M.P. [High Mesa Technologies LLC, Santa Fe, NM (United States)]|[High Mesa Technologies LLC, Irvine, CA (United States); Jones, M.R. [Electric Power Research Inst., Palo Alto, CA (United States)

    1996-07-01

    Silent electrical discharge plasma (dielectric barrier) reactors can decompose gas-phase pollutants by free-radical attack or electron-induced fragmentation. The radicals or electrons are produced by the large average volume nonthermal plasmas generated in the reactor. In the past decade, the barrier configuration has attracted attention for destroying toxic chemical agents for the military, removing harmful greenhouse gases, and treating other environmentally- hazardous chemical compounds. At the Los Alamos National Laboratory, we have been studying the silent discharge plasma (SDP) for processing gaseous-based hazardous chemicals for approximately five years. The key objective is to convert hazardous or toxic chemicals into non-hazardous compounds or into materials which are more easily managed. The main applications have been for treating off-gases from thermal treatment units, and for abating hazardous air-pollutant emissions (e.g., industrial air emissions, vapors extracted from contaminated soil or groundwater). In this paper, we will summarize the basic principles of SDP processing, discuss illustrative applications of the technology, and present results from small-scale field tests that are relevant to our commercialization effort.

  8. Final Technical Report: Science and technology reviews of FACE[Free Air Carbon Enrichment

    Energy Technology Data Exchange (ETDEWEB)

    Strain, Boyd R.

    1998-03-23

    The purpose of this grant was to bring together the principals of all known facilities that had been developed, principals who had submitted proposals to develop FACE facilities, and principals who want to develop proposals for facilities. In addition, critical program personnel from potential funding agencies and a few high level science administrators were invited to observe the proceedings and to visit a working FACE facility. The objectives of this study are to conduct a three-day international meeting on scientific aspects of research with the new and developing free air carbon enrichment (FACE) technology. Immediately following the science meeting, conduct a two-day international meeting on experimental protocols to be applied in FACE research. To conduct a four day international meeting on the assessment of the responses of forest ecosystems to elevated atmospheric carbon dioxide. The three meetings supported by this grant were all highly successful meetings and resulted in the formation of an organized and identified working group with the acronym InterFACE (International Free-Air Carbon Dioxide Enrichment) working group.

  9. A Method for Making Cross-Comparable Estimates of the Benefits of Decision Support Technologies for Air Traffic Management

    Science.gov (United States)

    Lee, David; Long, Dou; Etheridge, Mel; Plugge, Joana; Johnson, Jesse; Kostiuk, Peter

    1998-01-01

    We present a general method for making cross comparable estimates of the benefits of NASA-developed decision support technologies for air traffic management, and we apply a specific implementation of the method to estimate benefits of three decision support tools (DSTs) under development in NASA's advanced Air Transportation Technologies Program: Active Final Approach Spacing Tool (A-FAST), Expedite Departure Path (EDP), and Conflict Probe and Trial Planning Tool (CPTP). The report also reviews data about the present operation of the national airspace system (NAS) to identify opportunities for DST's to reduce delays and inefficiencies.

  10. 高级氧化技术处理废水的研究进展%The Research Progress of Advanced Oxidation Technology For Wastewater Treatment

    Institute of Scientific and Technical Information of China (English)

    朱心悦; 韦新东; 蒋宝军

    2015-01-01

    Advanced catalytic oxidation technology has become an important means of treating biological degradation of toxic organic pollutants, which has been widely used in the printing and dyeing, chemical, pesticide, papermaking, electroplating and printed circuit boards, hospitals, pharmaceutical, mining, etc. According to the free radical production mode and different reaction conditions, advanced oxidation technology can be divided into photochemical oxidation, catalytic ozone oxidation, electrochemical oxidation, Fenton oxidation, catalytic wet air oxidation, ultrasonic oxidation method and so on. Advanced oxidation technology has many advantages,but some technical methods remain in the stage of experiment.So a more efficient and perfect technology should be studied to realize large-scale industrial application.%高级催化氧化技术已经成为治理生物难降解有机有毒污染物的重要手段,在印染、化工、农药、造纸、电镀和印制板、制药、医院、矿山等领域以及垃圾渗滤液等废水的处理上已经获得应用,具有很好的应用前景。根据产生自由基的方式和反应条件的不同,可将高级氧化技术分为光化学氧化法、催化臭氧氧化法、电化学氧化法、芬顿(Fenton)氧化法、催化湿式氧化法、超声氧化法等。高级氧化技术具有诸多优点,但其中一些技术方法仍处于研究实验阶段。因此,需要研究一种更高效、完善的技术,以实现大规模工业化应用。

  11. Catalytic wet-air oxidation of lignin in a three-phase reactor with aromatic aldehyde production

    Directory of Open Access Journals (Sweden)

    Sales F.G.

    2004-01-01

    Full Text Available In the present work a process of catalytic wet air oxidation of lignin obtained from sugar-cane bagasse is developed with the objective of producing vanillin, syringaldehyde and p-hydroxybenzaldehyde in a continuous regime. Palladium supported on g-alumina was used as the catalyst. The reactions in the lignin degradation and aldehyde production were described by a kinetic model as a system of complex parallel and series reactions, in which pseudo-first-order steps are found. For the purpose of producing aromatic aldehydes in continuous regime, a three-phase fluidized reactor was built, and it was operated using atmospheric air as the oxidizer. The best yield in aromatic aldehydes was of 12%. The experimental results were compatible with those values obtained by the pseudo-heterogeneous axial dispersion model (PHADM applied to the liquid phase.

  12. Solid oxide cell R&D at Riso National Laboratory-and its transfer to technology

    DEFF Research Database (Denmark)

    Linderoth, Søren

    2009-01-01

    Risø National Laboratory has conducted R&D on solid oxide cells for almost 20 years—all the time together with industries with interest in deploying the technology when mature. Risø National Laboratory (Risø) and Topsoe Fuel Cell A/S (TOFC) have for several years jointly carried out a development...... by the consortium, e.g. a metal-supported cell. TOFC has an extended program to develop the SOFC technology all the way to a marketable product....

  13. Solid oxide cell R&D at Riso National Laboratory-and its transfer to technology

    DEFF Research Database (Denmark)

    Linderoth, Søren

    2009-01-01

    Risø National Laboratory has conducted R&D on solid oxide cells for almost 20 years—all the time together with industries with interest in deploying the technology when mature. Risø National Laboratory (Risø) and Topsoe Fuel Cell A/S (TOFC) have for several years jointly carried out a development...... by the consortium, e.g. a metal-supported cell. TOFC has an extended program to develop the SOFC technology all the way to a marketable product....

  14. Carvedilol alleviates adjuvant-induced arthritis and subcutaneous air pouch edema: Modulation of oxidative stress and inflammatory mediators

    Energy Technology Data Exchange (ETDEWEB)

    Arab, Hany H., E-mail: hany_h_arab@yahoo.com [Biochemistry Division, Department of Pharmacology and Toxicology, Faculty of Pharmacy, Taif University, Taif (Saudi Arabia); Department of Biochemistry, Faculty of Pharmacy, Cairo University, Cairo (Egypt); El-Sawalhi, Maha M. [Department of Biochemistry, Faculty of Pharmacy, Cairo University, Cairo (Egypt)

    2013-04-15

    Rheumatoid arthritis (RA) is a systemic inflammatory disease with cardiovascular complications as the leading cause of morbidity. Carvedilol is an adrenergic antagonist which has been safely used in treatment of several cardiovascular disorders. Given that carvedilol has powerful antioxidant/anti-inflammatory properties, we aimed to investigate its protective potential against arthritis that may add further benefits for its clinical usefulness especially in RA patients with concomitant cardiovascular disorders. Two models were studied in the same rat; adjuvant arthritis and subcutaneous air pouch edema. Carvedilol (10 mg/kg/day p.o. for 21 days) effectively suppressed inflammation in both models with comparable efficacy to the standard anti-inflammatory diclofenac (5 mg/kg/day p.o.). Notably, carvedilol inhibited paw edema and abrogated the leukocyte invasion to air pouch exudates. The latter observation was confirmed by the histopathological assessment of the pouch lining that revealed mitigation of immuno-inflammatory cell influx. Carvedilol reduced/normalized oxidative stress markers (lipid peroxides, nitric oxide and protein thiols) and lowered the release of inflammatory cytokines (TNF-α and IL-6), and eicosanoids (PGE{sub 2} and LTB{sub 4}) in sera and exudates of arthritic rats. Interestingly, carvedilol, per se, didn't present any effect on assessed biochemical parameters in normal rats. Together, the current study highlights evidences for the promising anti-arthritic effects of carvedilol that could be mediated through attenuation of leukocyte migration, alleviation of oxidative stress and suppression of proinflammatory cytokines and eicosanoids. - Highlights: ► Carvedilol possesses promising anti-arthritic properties. ► It markedly suppressed inflammation in adjuvant arthritis and air pouch edema. ► It abrogated the leukocyte invasion to air pouch exudates and linings. ► It reduced/normalized oxidative stress markers in sera and exudates of

  15. ESR investigation of the oxidative damage in lungs caused by asbestos and air pollution particles

    Science.gov (United States)

    Kadiiska, M. B.; Ghio, A. J.; Mason, R. P.

    2004-05-01

    Exposure to asbestos and air pollution particles can be associated with increased human morbidity and mortality. However, the molecular mechanism of lung injuries remains unknown. It has been postulated that the in vivo toxicity results from the catalysis of free radical generation. Using electron spin resonance (ESR) in conjunction with the spin trap α-(4-pyridyl-1-oxide)- N- tert-butylnitrone (4-POBN) we previously investigated in vivo free radical production by rats treated with intratracheal instillation of asbestos (crocidolite fibers) and an emission source air pollution particle (oil fly ash). In this report we compare the effect of two different exposures on the type of free radicals they induce in in vivo animal model. Twenty-four hours after the exposure, ESR spectroscopy of the chloroform extract from lungs of animals exposed to either asbestos or oil fly ash gave a spectrum consistent with a carbon-centered radical adduct ( aN=15.01 G and aH=2.46 G). To test whether free radical formation occurred in vivo and not in vitro, a number of control experiments were performed. Combinations (both individually and together) of asbestos or oil fly ash and 4-POBN were added to lung homogenate of unexposed rats prior to chloroform extraction. No detectable ESR signal resulted. To exclude the possibility of ex vivo free radical generation, asbestos or oil fly ash was added to lung homogenate of an animal treated with 4-POBN. Also, 4-POBN was added to lung homogenate from rats instilled with asbestos or oil fly ash. Neither system produced radical adducts, indicating that the ESR signal detected in the lung extracts of the treated animals must be produced in vivo and not ex vivo or in vitro. In conclusion, ESR analysis of lung tissue demonstrated that both exposures produce lipid-derived radical metabolites despite their different composition and structure. Analogously, both exposures provide evidence of in vivo enhanced lipid peroxidation. Furthermore, it is

  16. Protein oxidation in processed cheese slices treated with pulsed light technology.

    Science.gov (United States)

    Fernández, M; Ganan, M; Guerra, C; Hierro, E

    2014-09-15

    The effect of pulsed light technology on protein oxidation was studied in sliced processed cheese by measuring the protein-bound carbonyls with a spectrophotometric DNPH assay. Bovine serum albumin was also tested as a protein standard. Fluences of 0.7, 2.1, 4.2, 8.4 and 11.9 J/cm(2) were applied to vacuum-packaged cheese slices and to an aqueous solution of the protein. Treatments up to 4.2 J/cm(2) did not promote protein oxidation immediately after flashing either in cheese or in the standard. Samples treated with 8.4 and 11.9 J/cm(2) showed significantly higher carbonyl amounts than non-treated ones. Protein oxidation increased along cheese storage at 4°C, and differences among treatments remained. Further studies on the sensory properties will be needed to clarify the impact of pulsed light on processed cheese quality.

  17. Multifunctional silicon-based light emitting device in standard complementary metal-oxide-semiconductor technology

    Institute of Scientific and Technical Information of China (English)

    Wang Wei; Huang Bei-Ju; Dong Zan; Chen Hong-Da

    2011-01-01

    A three-terminal silicon-based light emitting device is proposed and fabricated in standard 0.35μm complementary metal-oxide-semiconductor technology. This device is capable of versatile working modes: it can emit visible to near infra-red (NIR) light (the spectrum ranges from 500 nm to 1000 nm) in reverse bias avalanche breakdown mode with working voltage between 8.35 V-12 V and emit NIR light (the spectrum ranges from 900 nm to 1300 nm) in the forward injection mode with working voltage below 2 V. An apparent modulation effect on the light intensity from the polysilicon gate is observed in the forward injection mode. Furthermore, when the gate oxide is broken down, NIR light is emitted from the polysilicon/oxide/silicon structure. Optoelectronic characteristics of the device working in different modes are measured and compared. The mechanisms behind these different emissions are explored.

  18. Electrochemical processing of spent nuclear fuels: An overview of oxide reduction in pyroprocessing technology

    Directory of Open Access Journals (Sweden)

    Eun-Young Choi

    2015-12-01

    Full Text Available The electrochemical reduction process has been used to reduce spent oxide fuel to a metallic form using pyroprocessing technology for a closed fuel cycle in combination with a metal-fuel fast reactor. In the electrochemical reduction process, oxides fuels are loaded at the cathode basket in molten Li2O–LiCl salt and electrochemically reduced to the metal form. Various approaches based on thermodynamic calculations and experimental studies have been used to understand the electrode reaction and efficiently treat spent fuels. The factors that affect the speed of the electrochemical reduction have been determined to optimize the process and scale-up the electrolysis cell. In addition, demonstrations of the integrated series of processes (electrorefining and salt distillation with the electrochemical reduction have been conducted to realize the oxide fuel cycle. This overview provides insight into the current status of and issues related to the electrochemical processing of spent nuclear fuels.

  19. Air Quality Management Using Modern Remote Sensing and Spatial Technologies and Associated Societal Costs

    Directory of Open Access Journals (Sweden)

    Waheed Uddin

    2006-09-01

    Full Text Available This paper presents a study of societal costs related to public health due to the degradation of air quality and the lack of physical activity, both affected by our built environment. The paper further shows road safety as another public health concern. Traffic fatalities are the number one cause of death in the world. Traffic accidents result in huge financial loss to the people involved and the related public health cost is a significant part of the total societal cost. Motor vehicle exhausts and industrial emissions, gasoline vapors, and chemical solvents as well as natural sources emit nitrogen oxides and volatile organic compounds, which are precursors to the formation of ground-level Ozone. High concentration values of ground-level Ozone in hot summer days produce smog and lead to respiratory problems and loss in worker’s productivity. These factors and associated economic costs to society are important in establishing public policy and decision-making for sustainable transportation and development of communities in both industrialized and developing countries. This paper presents new science models for predicting ground-level Ozone and related air quality degradation. The models include predictor variables of daily climatological data, traffic volume and mix, speed, aviation data, and emission inventory of point sources. These models have been implemented in the user friendly AQMAN computer program and used for a case study in Northern Mississippi. Lifecycle benefits from reduced societal costs can be used to implement sustainable transportation policies, enhance investment decision-making, and protect public health and the environment.

  20. Solid oxide electrolysis--a key enabling technology for sustainable energy scenarios.

    Science.gov (United States)

    Hansen, John Bøgild

    2015-01-01

    Production of fuels and chemicals from steam and/or CO2 with solid oxide electrolysis cells (SOEC) and electricity have attracted considerable interest recently. This paper is an extended version of the introductory lecture presented at the first Faraday Discussions meeting on the subject. The focus is on the state of the art of cells, stacks and systems. Thermodynamics, performance and degradation are addressed. Remaining challenges and potential application of the technology are discussed from an industrial perspective.

  1. Investigation of low temperature solid oxide fuel cells for air-independent UUV applications

    Science.gov (United States)

    Moton, Jennie Mariko

    Unmanned underwater vehicles (UUVs) will benefit greatly from high energy density (> 500 Wh/L) power systems utilizing high-energy-density fuels and air-independent oxidizers. Current battery-based systems have limited energy densities (electrolytes with operating temperatures of 650°C and lower may operate in the unique environments of a promising UUV power plant. The plant would contain a H 2O2 decomposition reactor to supply humidified O2 to the SOFC cathode and exothermic aluminum/H2O combustor to provide heated humidified H2 fuel to the anode. To characterize low-temperature SOFC performance with these unique O2 and H2 source, SOFC button cells based on nickel/GDC (Gd0.1Ce0.9O 1.95) anodes, GDC electrolytes, and lanthanum strontium cobalt ferrite (La0.6Sr0.4Co0.2Fe0.8O3-δ or LSCF)/GDC cathodes were fabricated and tested for performance and stability with humidity on both the anode and the cathode. Cells were also tested with various reactant concentrations of H2 and O2 to simulate gas depletion down the channel of an SOFC stack. Results showed that anode performance depended primarily on fuel concentration and less on the concentration of the associated increase in product H2O. O 2 depletion with humidified cathode flows also caused significant loss in cell current density at a given voltage. With the humidified flows in either the anode or cathode, stability tests of the button cells at 650 °C showed stable voltage is maintained at low operating current (0.17 A/cm2) at up to 50 % by mole H2O, but at higher current densities (0.34 A/cm2), irreversible voltage degradation occurred at rates of 0.8-3.7 mV/hour depending on exposure time. From these button cell results, estimated average current densities over the length of a low-temperature SOFC stack were estimated and used to size a UUV power system based on Al/H 2O oxidation for fuel and H2O2 decomposition for O2. The resulting system design suggested that energy densities above 300 Wh/L may be achieved at

  2. TREATMENT OF CYANIDE SOLUTIONS AND SLURRIES USING AIR-SPARGED HYDROCYCLONE (ASH) TECHNOLOGY

    Energy Technology Data Exchange (ETDEWEB)

    Jan D. Miller; Terrence Chatwin; Jan Hupka; Doug Halbe; Tao Jiang; Bartosz Dabrowski; Lukasz Hupka

    2003-03-31

    The two-year Department of Energy (DOE) project ''Treatment of Cyanide Solutions and Slurries Using Air-Sparged Hydrocyclone (ASH) Technology'' (ASH/CN) has been completed. This project was also sponsored by industrial partners, ZPM Inc., Elbow Creek Engineering, Solvay Minerals, EIMCO-Baker Process, Newmont Mining Corporation, Cherokee Chemical Co., Placer Dome Inc., Earthworks Technology, Dawson Laboratories and Kennecott Minerals. Development of a new technology using the air-sparged hydrocyclone (ASH) as a reactor for either cyanide recovery or destruction was the research objective. It was expected that the ASH could potentially replace the conventional stripping tower presently used for HCN stripping and absorption with reduced power costs. The project was carried out in two phases. The first phase included calculation of basic processing parameters for ASH technology, development of the flowsheet, and design/adaptation of the ASH mobile system for hydrogen cyanide (HCN) recovery from cyanide solutions. This was necessary because the ASH was previously used for volatile organics removal from contaminated water. The design and modification of the ASH were performed with the help from ZPM Inc. personnel. Among the modifications, the system was adapted for operation under negative pressure to assure safe operating conditions. The research staff was trained in the safe use of cyanide and in hazardous material regulations. Cyanide chemistry was reviewed resulting in identification of proper chemical dosages for cyanide destruction, after completion of each pilot plant run. The second phase of the research consisted of three field tests that were performed at the Newmont Mining Corporation gold cyanidation plant near Midas, Nevada. The first field test was run between July 26 and August 2, 2002, and the objective was to demonstrate continuous operation of the modified ASH mobile system. ASH units were applied for both stripping and absorption

  3. On the Ratio of Sulfur Dioxide to Nitrogen Oxides as an Indicator of Air Pollution Sources.

    Science.gov (United States)

    Nirel, Ronit; Dayan, Uri

    2001-07-01

    The ratio of sulfur dioxide to nitrogen oxides (RSN = SO2/NOx) is one indicator of air pollution sources. The role of this ratio in source attribution is illustrated here for the Ashdod area, located in the southern coastal plain of Israel. The main sources of pollution in the area are the tall stacks of the Eshkol power plant, the stacks of oil refineries, and areal sources (stationary and mobile). The factors that affect RSN are studied using four regression models: a binary regression tree in original scale, a tree in logarithmic scale, a data partition produced by a combination of the two trees, and a linear regression model. All models have similar relative prediction error, with the combined partition best highlighting the sources of variability in RSN: (a) very low values (interquartile range of [0.12, 0.48]) are associated with traffic, (b) low values ([0.43, 1.00]) are attributed to the power plant and to daytime emissions of local industry, (c) medium values ([0.74, 1.90]) are associated with local industry emissions during cooler hours of the day and refinery emissions mainly on slow wind episodes, and (d) high values ([1.07, 4.30]) are attributed to refinery emissions during moderate to fast wind episodes. Analysis of the number of episodes of increased concentrations indicates that, during 1996 and 1997, about 42% of SO2 episodes are attributable to the power plant and 33% to the refineries. Increased-NOx episodes are mainly contributed by traffic (91%) and power plant (4.5%) emissions.

  4. [Catalytic wet air oxidation of phenol with Ru/ZrO2-CeO2 catalyst].

    Science.gov (United States)

    Wang, Jian-bing; Zhu, Wan-peng; Wang, Wei; Yang, Shao-xia

    2007-07-01

    Wet air oxidation of phenol with Ru/ZrO2-CeO2 was systematically investigated and results showed that Ru/ZrO2-CeO2 could significantly increase the removal of COD and phenol. At the reaction temperature of 170 degrees C and pressure of 3MPa, about 99% COD and 100% phenol was removed respectively after 120 min. The optimal conditions were: reaction temperature, 170 degrees C; reaction pressure, 3 MPa; catalyst dosage, 5 g/L; agitator speed, 500 r/min. By analyzing intermediates, a simplified scheme of phenol oxidation was brought out. It includes two main steps. The first step is the production of organic acids, which is fast. The second step is the oxidation of organic acid, in which the oxidation of acetic acid is slow. Complete oxidation of acetic acid needs high temperature at which the radicals assault the C-H bond of a carbon and acetic acid is oxidized into carbon dioxide and water through formic acid.

  5. Study of Nanodispersed Iron Oxides Produced in Steel Drilling by Contracted Electric-Arc Air Plasma Torch

    Institute of Scientific and Technical Information of China (English)

    P. STEFANOV; D. GALANOV; G. VISSOKOV; D. PANEVA; B. KUNEV; I. MITOV

    2008-01-01

    The optimal conditions on the plasma-forming gas flowrate, discharge current and voltage, distance between the plasma-torch nozzle and the metal plate surface for the process of penetration in and vaporization of steel plates by the contracted electric-arc air plasma torch accompanied by water quenching, were determined. The X-ray structural and phase studies as well as M6ssbauer and electron microscope studies on the samples treated were performed. It was demonstrated that the vaporized elemental iron was oxidized by the oxygen present in the air plasma jet to form iron oxides (wiistite, magnetite, hematite), which, depending on their mass ra-tios, determined the color of the iron oxide pigments, namely, beginning from light yellow, through deep yellow, light brown, deep brown, violet, red-violet, to black. A high degree of dispersity of the iron oxides is thus produced, with an averaged diameter of the particles below 500 nm, and their defective crystal structure form the basis of their potential application as components of iron-containing catalysts and pigments.

  6. Study of Nanodispersed Iron Oxides Produced in Steel Drilling by Contracted Electric-Arc Air Plasma Torch

    Science.gov (United States)

    Stefanov, P.; Galanov, D.; Vissokov, G.; Paneva, D.; Kunev, B.; Mitov, I.

    2008-06-01

    The optimal conditions on the plasma-forming gas flowrate, discharge current and voltage, distance between the plasma-torch nozzle and the metal plate surface for the process of penetration in and vaporization of steel plates by the contracted electric-arc air plasma torch accompanied by water quenching, were determined. The X-ray structural and phase studies as well as Mössbauer and electron microscope studies on the samples treated were performed. It was demonstrated that the vaporized elemental iron was oxidized by the oxygen present in the air plasma jet to form iron oxides (wüstite, magnetite, hematite), which, depending on their mass ratios, determined the color of the iron oxide pigments, namely, beginning from light yellow, through deep yellow, light brown, deep brown, violet, red-violet, to black. A high degree of dispersity of the iron oxides is thus produced, with an averaged diameter of the particles below 500 nm, and their defective crystal structure form the basis of their potential application as components of iron-containing catalysts and pigments.

  7. Energy efficient air-conditioning technology for a healthier climate; Energieeffiziente Klimatechnik fuer ein gesundes Raumklima

    Energy Technology Data Exchange (ETDEWEB)

    Hartl, Thorsten [ebm-papst Motoren und Ventilatoren GmbH, St. Florian (Austria)

    2011-07-01

    Since climate and indoor air quality have a great impact on concentration, health and well being, it is important to provide good indoor air for example in classrooms. The use of air conditioning equipment enables an optimal air-conditioning, whether in new buildings or building alterations or renovations. Energy-saving EC fans in these air conditioning systems provide an efficient and quiet ventilation meeting the requirements. Thus, the contribution under consideration reports on centrifugal fans.

  8. Copper-catalyzed aerobic oxidative C-C bond cleavage of unstrained ketones with air and amines.

    Science.gov (United States)

    Zhou, Wang; Fan, Wenyou; Jiang, Qijian; Liang, Yu-Feng; Jiao, Ning

    2015-05-15

    A unique copper-catalyzed aerobic oxidative C-C bond cleavage of simple unstrained ketones with air and amines has been developed. In this chemistry, amides and oxo amides are easily synthesized through the selective C-C bond cleavage of simple ketones or unstrained cycloketones. The broad substrate scopes and use of an inexpensive copper catalyst and green molecular oxygen as an oxidant as well as an O-source make this protocol very attractive for potential synthetic applications. The control experiments reveal that the present copper-catalyzed oxidative C-C bond cleavage of simple ketones proceeds in a novel catalytic pathway rather than through the cleavage of a dioxetane intermediate.

  9. Reactive dye house wastewater treatment. Use of hybrid technology: Membrane, sonication followed by wet oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Dhale, A.D.; Mahajani, V.V. [Univ. of Mumbai (India)

    1999-05-01

    To address problems associated with treatment of an aqueous waste stream from a reactive dye house, a model dye, turquoise blue CI25, was studied. A hybrid technology, membrane separation followed by sonication and wet oxidation, has been demonstrated to treat the wastewater for reuse and discharge. Experiments were first performed with the reactive dye solution in water. A nanofiltration membrane (MPT 30) was found to be suitable to concentrate the dye. The concentrate was then treated with a wet oxidation process. Kinetics studies were performed with and without catalyst, in the temperature range of 170--215 C. The color destruction achieved was > 99%. After process parameters were fixed, studies were conducted with the actual dye waste stream. The actual waste stream was found to be refractory for wet oxidation under the above conditions. Sonication of the concentrate obtained after membrane filtration, in the presence of CuSO{sub 4}, made the waste stream amenable to wet oxidation. Sonication followed by wet oxidation was found to be more effective at near neutral conditions as compared to basic conditions.

  10. Application of Developed APCVD Transparent Conducting Oxides and Undercoat Technologies for Economical OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Silverman, Gary S.; Bluhm, Martin; Coffey, James; Korotkov, Roman; Polsz, Craig; Salemi, Alexandre; Smith, Robert; Smith, Ryan; Stricker, Jeff; Xu, Chen; Shirazi, Jasmine; Papakonstantopulous, George; Carson, Steve; Hartmann, Sören; Jessen, Frank; Krogmann, Bianaca; Rickers, Christoph; Ruske, Manfred; Schwab, Holger; Bertram, Dietrich

    2011-01-02

    Economics is a key factor for application of organic light emitting diodes (OLED) in general lighting relative to OLED flat panel displays that can handle high cost materials such as indium tin oxide (ITO) or Indium zinc oxide (IZO) as the transparent conducting oxide (TCO) on display glass. However, for OLED lighting to penetrate into general illumination, economics and sustainable materials are critical. The issues with ITO have been documented at the DOE SSL R&D and Manufacturing workshops for the last 5 years and the issue is being exaserbated by export controls from China (one of the major sources of elemental indium). Therefore, ITO is not sustainable because of the fluctuating costs and the United States (US) dependency on other nations such as China. Numerous alternatives to ITO/IZO are being evaluated such as Ag nanoparticles/nanowires, carbon nanotubes, graphene, and other metal oxides. Of these other metal oxides, doped zinc oxide has attracted a lot of attention over the last 10 years. The volume of zinc mined is a factor of 80,000 greater than indium and the US has significant volumes of zinc mined domestically, resulting in the ability for the US to be self-sufficient for this element that can be used in optoelectonic applications. The costs of elemental zinc is over 2 orders of magnitude less than indium, reflecting the relative abundance and availablility of the elements. Arkema Inc. and an international primary glass manufacturing company, which is located in the United States, have developed doped zinc oxide technology for solar control windows. The genesis of this DOE SSL project was to determine if doped zinc oxide technology can be taken from the commodity based window market and translate the technology to OLED lighting. Thus, Arkema Inc. sought out experts, Philips Lighting, Pacific Northwest National Laboratories (PNNL) and National Renewable Research Laboratories (NREL), in OLED devices and brought them into the project. This project had a

  11. A Novel Fully Depleted Air AlN Silicon-on-Insulator Metal-Oxide-Semiconductor Field Effect Transistor

    Institute of Scientific and Technical Information of China (English)

    YANG Yuan; GAO Yong; GONG Peng-Liang

    2008-01-01

    @@ A novel fully depleted air AlN silicon-on-insulator (SOI) metal-oxide-semiconductor field effect transistor (MOS-FET) is presented, which can eliminate the self-heating effect and solve the problem that the off-state current of SOI MOSFETs increases and the threshold voltage characteristics become worse when employing a high thermal conductivity material as a buried layer. The simulation results reveal that the lattice temperature in normal SOI devices is 75K higher than the atmosphere temperature, while the lattice temperature is just 4K higher than the atmosphere temperature resulting in less severe self-heating effect in air AlN SOI MOSFETs and AlN SOI MOSFETs. The on-state current of air AlN SOI MOSFETs is similar to the AlN SOI structure, and improves 12.3% more than that of normal SOI MOSFETs. The off-state current of AlN SOI is 6.7 times of normal SOI MOSFETs, while the counterpart of air AlN SOI MOSFETs is lower than that of SOI MOSFETs by two orders of magnitude. The threshold voltage change of air AlN SOI MOSFETs with different drain voltage is much less than that of AlN SOI devices, when the drain voltage is biased at 0.8 V, this difference is 28mV, so the threshold voltage change induced by employing high thermal conductivity material is cured.

  12. Air plasma-material interactions at the oxidized surface of the PM1000 nickel-chromium superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Panerai, Francesco, E-mail: panerai@vki.ac.be [Aeronautics and Aerospace Department, von Karman Institute for Fluid Dynamics, Chaussée de Waterloo 72, 1640 Rhode-Saint-Genèse (Belgium); Marschall, Jochen [Molecular Physics Program, SRI International, 333 Ravenswood Avenue, Menlo Park, CA 94025 (United States); Thömel, Jan [Aeronautics and Aerospace Department, von Karman Institute for Fluid Dynamics, Chaussée de Waterloo 72, 1640 Rhode-Saint-Genèse (Belgium); Vandendael, Isabelle; Hubin, Annick [Department of Materials and Chemistry, Research Group of Electrochemical and Surface Engineering, Vrije Universiteit Brussel, Pleinlaan 2, B-1050 Brussels (Belgium); Chazot, Olivier [Aeronautics and Aerospace Department, von Karman Institute for Fluid Dynamics, Chaussée de Waterloo 72, 1640 Rhode-Saint-Genèse (Belgium)

    2014-10-15

    Highlights: • A detail investigation on behavior of a Ni–Cr superalloy under air plasma is proposed. • The response of PM1000 specimens at high temperature/low pressure is characterized. • High volatility of Cr{sub 2}O{sub 3} scale in presence of oxygen is found experimentally. • Stability of NiO scale at the surface is observed. • Computed thermodynamic volatility diagrams confirm the experimental observations. - Abstract: Nickel-based superalloys are promising options for the thermal protection systems of hypersonic re-entry vehicles operating under moderate aerothermal heating conditions. We present an experimental study on the interactions between PM1000, an oxide dispersion strengthened nickel-chromium superalloy, and air plasma at surface temperatures between 1000 and 1600 K and pressures of 1500, 7500 and 10,000 Pa. Pre-oxidized PM1000 specimens are tested in high-enthalpy reactive air plasma flows generated by the Plasmatron wind tunnel at the von Karman Institute for Fluid Dynamics. Microscopic analysis of plasma-exposed specimens shows enhanced damage to the chromia scale at the lowest plasma pressure. Elemental surface analysis reveals the loss of Cr and the enhancement of Ni at the scale surface. A thermodynamic analysis supports the accelerated volatilization of Cr{sub 2}O{sub 3} and the relative stability of NiO in the presence of atomic oxygen. Changes in the reflectance and emissivity of the oxidized surfaces due to plasma-exposure are presented. The catalytic efficiencies for dissociated air species recombination are determined as a function of surface temperature and pressure through a numerical rebuilding procedure and are compared with values presented in the literature for the same material.

  13. Oxidation characteristics of Beta-21S in air in the temperature range 600 to 800 C

    Science.gov (United States)

    Wallace, Terryl A.; Clark, Ronald K.; Wiedemann, Karl E.

    1992-01-01

    The metastable beta-Ti alloy Beta-21S, Ti-15Mo-2.7Nb-3Al-0.2Si (weight percent), has been proposed as a candidate for use in metal matrix composites in future hypersonic vehicles. The present study investigated the oxidation behavior of Beta-21S over the temperature range 600 C to 800 C. Oxidation weight gain was evaluated using thermogravimetric analysis. Oxidized specimens were evaluated using x ray diffraction techniques, scanning electron microscopy, energy dispersive x ray analysis, and electron microprobe analysis to identify oxidation products and evaluate oxidation damage to the alloy.

  14. Air2Air{trademark} water-saving technology goes on line at PNM's San Juan station

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-06-15

    The US Department of Energy's National Energy Technology Laboratory estimates that US power plant cooling towers evaporate a total of no less than three billion gallons of water each day. A new technology from SPX currently under test at Public Service of New Mexico's San Juan coal fired unit could provide a way of recovering some of this. 1 fig.

  15. A perovskite oxide with high conductivities in both air and reducing atmosphere for use as electrode for solid oxide fuel cells

    Science.gov (United States)

    Lan, Rong; Cowin, Peter I.; Sengodan, Sivaprakash; Tao, Shanwen

    2016-08-01

    Electrode materials which exhibit high conductivities in both oxidising and reducing atmospheres are in high demand for solid oxide fuel cells (SOFCs) and solid oxide electrolytic cells (SOECs). In this paper, we investigated Cu-doped SrFe0.9Nb0.1O3‑δ finding that the primitive perovskite oxide SrFe0.8Cu0.1Nb0.1O3‑δ (SFCN) exhibits a conductivity of 63 Scm‑1and 60 Scm‑1 at 415 °C in air and 5%H2/Ar respectively. It is believed that the high conductivity in 5%H2/Ar is related to the exsolved Fe (or FeCu alloy) on exposure to a reducing atmosphere. To the best of our knowledge, the conductivity of SrFe0.8Cu0.1Nb0.1O3‑δ in a reducing atmosphere is the highest of all reported oxides which also exhibit a high conductivity in air. Fuel cell performance using SrFe0.8Cu0.1Nb0.1O3‑δ as the anode, (Y2O3)0.08(ZrO2)0.92 as the electrolyte and La0.8Sr0.2FeO3‑δ as the cathode achieved a power density of 423 mWcm‑2 at 700 °C indicating that SFCN is a promising anode for SOFCs.

  16. A perovskite oxide with high conductivities in both air and reducing atmosphere for use as electrode for solid oxide fuel cells.

    Science.gov (United States)

    Lan, Rong; Cowin, Peter I; Sengodan, Sivaprakash; Tao, Shanwen

    2016-08-22

    Electrode materials which exhibit high conductivities in both oxidising and reducing atmospheres are in high demand for solid oxide fuel cells (SOFCs) and solid oxide electrolytic cells (SOECs). In this paper, we investigated Cu-doped SrFe0.9Nb0.1O3-δ finding that the primitive perovskite oxide SrFe0.8Cu0.1Nb0.1O3-δ (SFCN) exhibits a conductivity of 63 Scm(-1)and 60 Scm(-1) at 415 °C in air and 5%H2/Ar respectively. It is believed that the high conductivity in 5%H2/Ar is related to the exsolved Fe (or FeCu alloy) on exposure to a reducing atmosphere. To the best of our knowledge, the conductivity of SrFe0.8Cu0.1Nb0.1O3-δ in a reducing atmosphere is the highest of all reported oxides which also exhibit a high conductivity in air. Fuel cell performance using SrFe0.8Cu0.1Nb0.1O3-δ as the anode, (Y2O3)0.08(ZrO2)0.92 as the electrolyte and La0.8Sr0.2FeO3-δ as the cathode achieved a power density of 423 mWcm(-2) at 700 °C indicating that SFCN is a promising anode for SOFCs.

  17. Development of open air silicon deposition technology by silane-free atmospheric pressure plasma enhanced chemical transport under local ambient gas control

    Science.gov (United States)

    Naito, Teruki; Konno, Nobuaki; Yoshida, Yukihisa

    2016-07-01

    Open air silicon deposition was performed by combining silane-free atmospheric pressure plasma-enhanced chemical transport and a newly developed local ambient gas control technology. The effect of air contamination on silicon deposition was investigated using a vacuum chamber, and the allowable air contamination level was confirmed to be 3 ppm. The capability of the local ambient gas control head was investigated numerically and experimentally. A safe and clean process environment with air contamination less than 1 ppm was achieved. Combining these technologies, a microcrystalline silicon film was deposited in open air, the properties of which were comparable to those of silicon films deposited in a vacuum chamber.

  18. Preliminary assessment of air quality for sulphur dioxide, nitrogen dioxide, nitrogen oxides, particulate matter, and lead in the Netherlands under European legislation

    NARCIS (Netherlands)

    Breugel PB van; Buijsman E; LLO

    2001-01-01

    The current air quality in the Netherlands for sulphur dioxide, nitrogen dioxide, nitrogen oxides, particulate matter and lead has been assessed in the context of limit values, margins of tolerance and the assessment thresholds used in the first daughter directive for air quality of the European

  19. Advancing Sequential Managed Aquifer Recharge Technology (SMART Using Different Intermediate Oxidation Processes

    Directory of Open Access Journals (Sweden)

    Karin Hellauer

    2017-03-01

    Full Text Available Managed aquifer recharge (MAR systems are an efficient barrier for many contaminants. The biotransformation of trace organic chemicals (TOrCs strongly depends on the redox conditions as well as on the dissolved organic carbon availability. Oxic and oligotrophic conditions are favored for enhanced TOrCs removal which is obtained by combining two filtration systems with an intermediate aeration step. In this study, four parallel laboratory-scale soil column experiments using different intermittent aeration techniques were selected to further optimize TOrCs transformation during MAR: no aeration, aeration with air, pure oxygen and ozone. Rapid oxygen consumption, nitrate reduction and dissolution of manganese confirmed anoxic conditions within the first filtration step, mimicking traditional bank filtration. Aeration with air led to suboxic conditions, whereas oxidation by pure oxygen and ozone led to fully oxic conditions throughout the second system. The sequential system resulted in an equal or better transformation of most TOrCs compared to the single step bank filtration system. Despite the fast oxygen consumption, acesulfame, iopromide, iomeprol and valsartan were degraded within the first infiltration step. The compounds benzotriazole, diclofenac, 4-Formylaminoantipyrine, gabapentin, metoprolol, valsartan acid and venlafaxine revealed a significantly enhanced removal in the systems with intermittent oxidation compared to the conventional treatment without aeration. Further improvement of benzotriazole and gabapentin removal by using pure oxygen confirmed potential oxygen limitation in the second column after aeration with air. Ozonation resulted in an enhanced removal of persistent compounds (i.e., carbamazepine, candesartan, olmesartan and further increased the attenuation of gabapentin, methylbenzotriazole, benzotriazole, and venlafaxine. Diatrizoic acid revealed little degradation in an ozone–MAR hybrid system.

  20. Improved Thermally Grown Oxide Scale in Air Plasma Sprayed NiCrAlY/Nano-YSZ Coatings

    Directory of Open Access Journals (Sweden)

    Mohammadreza Daroonparvar

    2013-01-01

    Full Text Available Oxidation has been considered as one of the principal disruptive factors in thermal barrier coating systems during service. So, oxidation behavior of thermal barrier coating (TBC systems with nanostructured and microstructured YSZ coatings was investigated at 1000∘C for 24 h, 48 h, and 120 h. Air plasma sprayed nano-YSZ coating exhibited a trimodal structure. Microstructural characterization also demonstrated an improved thermally grown oxide scale containing lower spinels in nano-TBC system after 120 h of oxidation. This phenomenon is mainly related to the unique structure of the nano-YSZ coating, which acted as a strong barrier for oxygen diffusion into the TBC system at elevated temperatures. Nearly continues but thinner Al2O3 layer formation at the NiCrAlY/nano-YSZ interface was seen, due to lower oxygen infiltration into the system. Under this condition, spinels formation and growth on the Al2O3 oxide scale were diminished in nano-TBC system compared to normal TBC system.

  1. Nitric oxide and nitrous oxide turnover in natural and engineered microbial communities: biological pathways, chemical reactions and novel technologies

    Directory of Open Access Journals (Sweden)

    Frank eSchreiber

    2012-10-01

    Full Text Available Nitrous oxide (N2O is an environmentally important atmospheric trace gas because it is an effective greenhouse gas and it leads to ozone depletion through photo-chemical nitric oxide (NO production in the stratosphere. Mitigating its steady increase in atmospheric concentration requires an understanding of the mechanisms that lead to its formation in natural and engineered microbial communities. N2O is formed biologically from the oxidation of hydroxylamine (NH2OH or the reduction of nitrite (NO2- to NO and further to N2O. Our review of the biological pathways for N2O production shows that apparently all organisms and pathways known to be involved in the catabolic branch of microbial N-cycle have the potential to catalyze the reduction of NO2- to NO and the further reduction of NO to N2O, while N2O formation from NH2OH is only performed by ammonia oxidizing bacteria. In addition to biological pathways, we review important chemical reactions that can lead to NO and N2O formation due to the reactivity of NO2-, NH2OH and nitroxyl (HNO. Moreover, biological N2O formation is highly dynamic in response to N-imbalance imposed on a system. Thus, understanding NO formation and capturing the dynamics of NO and N2O build-up are key to understand mechanisms of N2O release. Here, we discuss novel technologies that allow experiments on NO and N2O formation at high temporal resolution, namely NO and N2O microelectrodes and the dynamic analysis of the isotopic signature of N2O with quantum cascade laser based absorption spectroscopy. In addition, we introduce other techniques that use the isotopic composition of N2O to distinguish production pathways and findings that were made with emerging molecular techniques in complex environments. Finally, we discuss how a combination of the presented tools might help to address important open questions on pathways and controls of nitrogen flow through complex microbial communities that eventually lead to N2O build-up.

  2. Electron transfer number control of the oxygen reduction reaction on nitrogen-doped reduced graphene oxides for the air electrodes of zinc-air batteries and organic degradation

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Sheng-Hui; Li, Po-Chieh; Hu, Chi-Chang, E-mail: cchu@che.nthu.edu.tw

    2016-11-01

    The mean electron transfer number (n) of the oxygen reduction reaction (ORR) on reduced graphene oxide (rGO) is controlled by nitrogen doping for the air electrodes of Zn-air batteries and electrochemical organic degradation. Melamine and pyrrole are employed as the nitrogen sources for fabricating N-doped rGO (N-rGO) by microwave-assisted hydrothermal synthesis (MAHS). The n value of the ORR is determined by the rotating ring-disk electrode (RRDE) voltammetry and is successfully controlled from 2.34 to 3.93 by preparation variables. The N-doped structures are examined by the x-ray photoelectron spectroscopic (XPS) analysis. The morphology and the defect degree of N-rGOs are characterized by high resolution transmission electron microscopy (HR-TEM) and Raman spectroscopy. N-rGOs with high and low n values are employed as the air electrode catalysts of zinc-air batteries and in-situ hydrogen peroxide (H{sub 2}O{sub 2}) generation, respectively. The highest discharge cell voltage of 1.235 V for a Zn-air battery is obtained at 2 mA cm{sup −2} meanwhile the current efficiency of H{sub 2}O{sub 2} generation in 1-h electrolysis at 0 V (vs. RHE) reaches 43%. The electrocatalytic degradation of orange G (OG), analyzed by UV-VIS absorption spectra, reveals a high decoloration degree from the relative absorbance of 0.38 for the azo π-conjugation structure of OG. - Highlights: • The mean electron transfer number (n) is controlled by nitrogen doping. • Melamine and pyrrole are used as the nitrogen sources for fabricating N-rGO. • The n value is successfully controlled from 2.34 to 3.93 by preparation variables. • The highest discharge cell voltage of 1.235 V for a Zn-air battery. • The current efficiency of H{sub 2}O{sub 2} generation 1-h electrolysis reaches 43%.

  3. New Effective Material Couple--Oxide Ceramic and Carbon Nanotube-- Developed for Aerospace Microsystem and Micromachine Technologies

    Science.gov (United States)

    Miyoshi, Kazuhisa; VanderWal, Randall L.; Tomasek, Aaron J.; Sayir, Ali; Farmer, Serene C.

    2004-01-01

    The prime driving force for using microsystem and micromachine technologies in transport vehicles, such as spacecraft, aircraft, and automobiles, is to reduce the weight, power consumption, and volume of components and systems to lower costs and increase affordability and reliability. However, a number of specific issues need to be addressed with respect to using microsystems and micromachines in aerospace applications--such as the lack of understanding of material characteristics; methods for producing and testing the materials in small batches; the limited proven durability and lifetime of current microcomponents, packaging, and interconnections; a cultural change with respect to system designs; and the use of embedded software, which will require new product assurance guidelines. In regards to material characteristics, there are significant adhesion, friction, and wear issues in using microdevices. Because these issues are directly related to surface phenomena, they cannot be scaled down linearly and they become increasingly important as the devices become smaller. When microsystems have contacting surfaces in relative motion, the adhesion and friction affect performance, energy consumption, wear damage, maintenance, lifetime and catastrophic failure, and reliability. Ceramics, for the most part, do not have inherently good friction and wear properties. For example, coefficients of friction in excess of 0.7 have been reported for ceramics and ceramic composite materials. Under Alternate Fuels Foundation Technologies funding, two-phase oxide ceramics developed for superior high-temperature wear resistance in NASA's High Operating Temperature Propulsion Components (HOTPC) project and new two-layered carbon nanotube (CNT) coatings (CNT topcoat/iron bondcoat/quartz substrate) developed in NASA's Revolutionary Aeropropulsion Concepts (RAC) project have been chosen as a materials couple for aerospace applications, including micromachines, in the nanotechnology

  4. Saving energy and improving IAQ through application of advanced air cleaning technologies

    Energy Technology Data Exchange (ETDEWEB)

    Fisk, W.J; Destaillats, H.; Sidheswaran, M.A.

    2011-03-01

    In the future, we may be able use air cleaning systems and reduce rates of ventilation (i.e., reduce rates of outdoor air supply) to save energy, with indoor air quality (IAQ) remaining constant or even improved. The opportunity is greatest for commercial buildings because they usually have a narrower range of indoor pollutant sources than homes. This article describes the types of air cleaning systems that will be needed in commercial buildings.

  5. Fragrance compound geraniol forms contact allergens on air exposure. Identification and quantification of oxidation products and effect on skin sensitization.

    Science.gov (United States)

    Hagvall, Lina; Bäcktorp, Carina; Svensson, Sophie; Nyman, Gunnar; Börje, Anna; Karlberg, Ann-Therese

    2007-05-01

    Fragrances are common causes of contact allergy. Geraniol (trans-3,7-dimethyl-2,6-octadiene-1-ol) is an important fragrance terpene. It is considered a weak contact allergen and is used for fragrance allergy screening among consecutive dermatitis patients. Analogous to other monoterpenes studied, such as limonene and linalool, geraniol has the potential to autoxidize on air exposure and form highly allergenic compounds. The aim of the present study was to investigate and propose a mechanism for the autoxidation of geraniol at room temperature. To investigate whether allergenic compounds are formed, the sensitizing potency of geraniol itself, air-exposed geraniol, and its oxidation products was determined using the local lymph node assay in mice. The results obtained show that the allylic alcohol geraniol follows an oxidation pattern different from those of linalool and limonene, which autoxidize forming hydroperoxides as the only primary oxidation products. The autoxidation of geraniol follows two paths, originating from allylic hydrogen abstraction near the two double bonds. From geraniol, hydrogen peroxide is primarily formed together with aldehydes geranial and neral from a hydroxyhydroperoxide. In addition, small amounts of a hydroperoxide are formed, analogous to the formation of the major linalool hydroperoxide. The autoxidation of geraniol greatly influenced the sensitizing effect of geraniol. The oxidized samples had moderate sensitizing capacity, quite different from that of pure geraniol. The hydroperoxide formed is believed to be the major contributor to allergenic activity, together with the aldehydes geranial and neral. On the basis of the present study and previous experience, we recommend that the possibility of autoxidation and the subsequent formation of contact allergenic oxidation products are considered in risk assessments performed on fragrance terpenes.

  6. Application of Developed APCVD Transparent Conducting Oxides and Undercoat Technologies for Economical OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Martin Bluhm; James Coffey; Roman Korotkov; Craig Polsz; Alexandre Salemi; Robert Smith; Ryan Smith; Jeff Stricker; Chen Xu; Jasmine Shirazi; George Papakonstantopulous; Steve Carson; Claudia Goldman; Soren Hartmann; Frank Jessen; Bianca Krogmann; Christoph Rickers; Manfred Ruske; Holger Schwab; Dietrich Bertram

    2011-01-02

    Economics is a key factor for application of organic light emitting diodes (OLED) in general lighting relative to OLED flat panel displays that can handle high cost materials such as indium tin oxide (ITO) or Indium zinc oxide (IZO) as the transparent conducting oxide (TCO) on display glass. However, for OLED lighting to penetrate into general illumination, economics and sustainable materials are critical. The issues with ITO have been documented at the DOE SSL R&D and Manufacturing workshops for the last 5 years and the issue is being exacerbated by export controls from China (one of the major sources of elemental indium). Therefore, ITO is not sustainable because of the fluctuating costs and the United States (US) dependency on other nations such as China. Numerous alternatives to ITO/IZO are being evaluated such as Ag nanoparticles/nanowires, carbon nanotubes, graphene, and other metal oxides. Of these other metal oxides, doped zinc oxide has attracted a lot of attention over the last 10 years. The volume of zinc mined is a factor of 80,000 greater than indium and the US has significant volumes of zinc mined domestically, resulting in the ability for the US to be self-sufficient for this element that can be used in optoelectronic applications. The costs of elemental zinc is over 2 orders of magnitude less than indium, reflecting the relative abundance and availability of the elements. Arkema Inc. and an international primary glass manufacturing company, which is located in the United States, have developed doped zinc oxide technology for solar control windows. The genesis of this DOE SSL project was to determine if doped zinc oxide technology can be taken from the commodity based window market and translate the technology to OLED lighting. Thus, Arkema Inc. sought out experts, Philips Lighting, Pacific Northwest National Laboratories (PNNL) and National Renewable Research Laboratories (NREL), in OLED devices and brought them into the project. This project had a

  7. Biofluid metabotyping of occupationally exposed subjects to air pollution demonstrates high oxidative stress and deregulated amino acid metabolism

    Science.gov (United States)

    Pradhan, Surya Narayan; Das, Aleena; Meena, Ramovatar; Nanda, Ranjan Kumar; Rajamani, Paulraj

    2016-10-01

    Occupational exposure to air pollution induces oxidative stress and prolonged exposure increases susceptibility to cardiovascular and respiratory diseases in several working groups. Biofluid of these subjects may reflect perturbed metabolic phenotypes. In this study we carried out a comparative molecular profiling study using parallel biofluids collected from subjects (n = 85) belonging to auto rickshaw drivers (ARD), traffic cops (TC) and office workers (OW). Higher levels of oxidative stress and inflammation markers in serum of ARD subjects were observed as compared to OW and TC. Uni and multivariate analyses of metabolites identified in urine by 1H NMR revealed 11 deregulated molecules in ARD subjects and involved in phenylalanine, histidine, arginine and proline metabolism. Despite contribution of confounding factors like exposure period, dietary factors including smoking and alcohol status, our results demonstrate existence of exposure specific metabotypes in biofluids of ARD, OW and TC groups. Monitoring serum oxidative stress and inflammation markers and urine metabolites by NMR may be useful to characterize perturbed metabolic phenotypes in populations exposed to urban traffic air pollution.

  8. Biofluid metabotyping of occupationally exposed subjects to air pollution demonstrates high oxidative stress and deregulated amino acid metabolism

    Science.gov (United States)

    Pradhan, Surya Narayan; Das, Aleena; Meena, Ramovatar; Nanda, Ranjan Kumar; Rajamani, Paulraj

    2016-01-01

    Occupational exposure to air pollution induces oxidative stress and prolonged exposure increases susceptibility to cardiovascular and respiratory diseases in several working groups. Biofluid of these subjects may reflect perturbed metabolic phenotypes. In this study we carried out a comparative molecular profiling study using parallel biofluids collected from subjects (n = 85) belonging to auto rickshaw drivers (ARD), traffic cops (TC) and office workers (OW). Higher levels of oxidative stress and inflammation markers in serum of ARD subjects were observed as compared to OW and TC. Uni and multivariate analyses of metabolites identified in urine by 1H NMR revealed 11 deregulated molecules in ARD subjects and involved in phenylalanine, histidine, arginine and proline metabolism. Despite contribution of confounding factors like exposure period, dietary factors including smoking and alcohol status, our results demonstrate existence of exposure specific metabotypes in biofluids of ARD, OW and TC groups. Monitoring serum oxidative stress and inflammation markers and urine metabolites by NMR may be useful to characterize perturbed metabolic phenotypes in populations exposed to urban traffic air pollution. PMID:27767182

  9. Oxidation behaviour of experimental Co-Re-base alloys in laboratory air at 1000 C

    Energy Technology Data Exchange (ETDEWEB)

    Klauke, Michael; Mukherji, Debashis; Roesler, Joachim [Technische Universitaet Braunschweig, Institut fuer Werkstoffe (Germany); Gorr, Bronislava; Christ, Hans-Juergen [Universitaet Siegen, Institut fuer Werkstofftechnik (Germany); Braz da Trindade Filho, Vicente [Vallourec und Mannesmann Tubes, Duesseldorf (Germany)

    2009-01-15

    The oxidation behaviour of experimental Co-Re-based alloy at 1000 C was studied. A set of binary, ternary and quaternary alloys from the Co-Re-Cr-C system was used as model alloys to understand the role each alloying element plays on oxidation. The morphology and composition of the oxide scale that formed was analysed by X-ray diffraction, energy dispersive spectroscopy and scanning electron microscopy. It was found that the present Co-Re alloys with 23 at.% and 30 at.% Cr additions behaved very similarly to Co-Cr binary alloys with equivalent Cr content. The oxide scale was multilayered, consisting of a dense CoO outer layer, a porous mixed oxide layer containing Co-oxide and Co-Cr spinel, and a discontinuous and non-protective Cr{sub 3}O{sub 2} layer. The binary Co-Re alloy behaved differently in oxidation, and it formed only a monolithic CoO scale. However, Re in combination with Cr promotes Cr-Re-rich {sigma} phase formation, which oxidises preferentially compared to the Co matrix. Carbon ties up part of the Cr to form Cr{sub 23}C{sub 6} type carbides. However, these carbides are not stable at 1000 C and dissolved with time, therefore C had only a minor role in the oxidation behaviour. In general, increasing Cr content in the alloy improved oxidation resistance. (orig.)

  10. 78 FR 54813 - Approval and Promulgation of Air Quality Implementation Plans; Maine; Oxides of Nitrogen...

    Science.gov (United States)

    2013-09-06

    ... Nitrogen Exemption and Ozone Transport Region Restructuring AGENCY: Environmental Protection Agency (EPA...; Oxides of Nitrogen Exemption and Ozone Transport Region Restructuring (August 5, 2013). The EPA...

  11. Optimization Of Technology For The Systems Of Hard-Oxide Layers By Spectroscopic Methods

    Science.gov (United States)

    Fluck, K.; Szalai, G.; Kojnok, J.; Szász, A.

    1986-10-01

    The well-known evaporating process of hard-oxid coatings for laser mirrors has many uncontrolled parameters. This paper deals with the Ti0,-SiO2 hard-oxides systems. The optimization of technology is based on optical [transmission; reflection parameters etc), spectroscopical [soft x-ray emission spectroscopy /SXES/, x-ray fluorescence spectroscopy /XFS/], structural (x-ray diffraction /XRD/) and damage threshold /DT/ examinations. The Ti02 was found in the evaporated layers in two equilibrium phases - rutil and anatase - depending on the evapora-tion conditions. The rutil phase was better than the anatase considering the DT for mirrors at λ=]1064 µm. The explanation is based on the difference of the near-infrared absorbtion between rutil and anatase phase of Ti02.

  12. Life cycle inventory analysis of regenerative thermal oxidation of air emissions from oriented strand board facilities in Minnesota - a perspective of global climate change

    Energy Technology Data Exchange (ETDEWEB)

    Nicholson, W.J. [Potlatch Corp., San Francisco, CA (United States)

    1997-12-31

    Life cycle inventory analysis has been applied to the prospective operation of regenerative thermal oxidation (RTO) technology at oriented strand board plants at Bemidji (Line 1) and Cook, Minnesota. The net system destruction of VOC`s and carbon monoxide, and at Cook a small quantity of particulate, has a very high environmental price in terms of energy and water use, global warming potential, sulfur and nitrogen oxide emissions, solids discharged to water, and solid waste deposited in landfills. The benefit of VOC destruction is identified as minor in terms of ground level ozone at best and possibly slightly detrimental. Recognition of environmental tradeoffs associated with proposed system changes is critical to sound decision-making. There are more conventional ways to address carbon monoxide emissions than combustion in RTO`s. In an environment in which global warming is a concern, fuel supplemental combustion for environmental control does not appear warranted. Consideration of non-combustion approaches to address air emission issues at the two operations is recommended. 1 ref., 5 tabs.

  13. Kinetics of Passive Oxidation of Hi-Nicalon-S SiC Fibers in Wet Air: Relationships between Si02 Scale Thickness, Crystallization, and Fiber Strength (Preprint)

    Science.gov (United States)

    2012-07-01

    crystallize to cristobalite and tridymite in 100 hours at 1000°C or in one hour at 1300°C. Crystallization kinetics for oxidation in wet air were...measured by TEM. Oxidation initially produces an amorphous scale that starts to crystallize to cristobalite and tridymite in 100 hours at 1000°C or in...using reflected light interference fringes observed by optical microscopy. Cross-sectional TEM specimens were prepared from oxidized fibers by

  14. Technology Solutions Case Study: Ventilation System Effectiveness and Tested Indoor Air Quality Impacts

    Energy Technology Data Exchange (ETDEWEB)

    A. Rudd and D. Bergey

    2015-08-01

    Ventilation system effectiveness testing was conducted at two unoccupied, single-family, detached lab homes at the University of Texas - Tyler. Five ventilation system tests were conducted with various whole-building ventilation systems. Multizone fan pressurization testing characterized building and zone enclosure leakage. PFT testing showed multizone air change rates and interzonal airflow filtration. Indoor air recirculation by a central air distribution system can help improve the exhaust ventilation system by way of air mixing and filtration. In contrast, the supply and balanced ventilation systems showed that there is a significant benefit to drawing outside air from a known outside location, and filtering and distributing that air. Compared to the Exhaust systems, the CFIS and ERV systems showed better ventilation air distribution and lower concentrations of particulates, formaldehyde and other VOCs.

  15. A dose-controlled system for air-liquid interface cell exposure and application to zinc oxide nanoparticles

    Directory of Open Access Journals (Sweden)

    Ferron George A

    2009-12-01

    Full Text Available Abstract Background Engineered nanoparticles are becoming increasingly ubiquitous and their toxicological effects on human health, as well as on the ecosystem, have become a concern. Since initial contact with nanoparticles occurs at the epithelium in the lungs (or skin, or eyes, in vitro cell studies with nanoparticles require dose-controlled systems for delivery of nanoparticles to epithelial cells cultured at the air-liquid interface. Results A novel air-liquid interface cell exposure system (ALICE for nanoparticles in liquids is presented and validated. The ALICE generates a dense cloud of droplets with a vibrating membrane nebulizer and utilizes combined cloud settling and single particle sedimentation for fast (~10 min; entire exposure, repeatable (2. The cell-specific deposition efficiency is currently limited to 0.072 (7.2% for two commercially available 6-er transwell plates, but a deposition efficiency of up to 0.57 (57% is possible for better cell coverage of the exposure chamber. Dose-response measurements with ZnO nanoparticles (0.3-8.5 μg/cm2 showed significant differences in mRNA expression of pro-inflammatory (IL-8 and oxidative stress (HO-1 markers when comparing submerged and air-liquid interface exposures. Both exposure methods showed no cellular response below 1 μg/cm2 ZnO, which indicates that ZnO nanoparticles are not toxic at occupationally allowed exposure levels. Conclusion The ALICE is a useful tool for dose-controlled nanoparticle (or solute exposure of cells at the air-liquid interface. Significant differences between cellular response after ZnO nanoparticle exposure under submerged and air-liquid interface conditions suggest that pharmaceutical and toxicological studies with inhaled (nano-particles should be performed under the more realistic air-liquid interface, rather than submerged cell conditions.

  16. Evaluating the impact of ambient benzene vapor concentrations on product water from Condensation Water From Air technology.

    Science.gov (United States)

    Kinder, Katherine M; Gellasch, Christopher A; Dusenbury, James S; Timmes, Thomas C; Hughes, Thomas M

    2017-07-15

    Globally, drinking water resources are diminishing in both quantity and quality. This situation has renewed interest in Condensation Water From Air (CWFA) technology, which utilizes water vapor in the air to produce water for both potable and non-potable purposes. However, there are currently insufficient data available to determine the relationship between air contaminants and the rate at which they are transferred from the air into CWFA untreated product water. This study implemented a novel experimental method utilizing an environmental test chamber to evaluate how air quality and temperature affects CWFA untreated product water quality in order to collect data that will inform the type of water treatment required to protect human health. This study found that temperature and benzene air concentration affected the untreated product water from a CWFA system. Benzene vapor concentrations representing a polluted outdoor environment resulted in benzene product water concentrations between 15% and 23% of the USEPA drinking water limit of 5μg/l. In contrast, product water benzene concentrations representing an indoor industrial environment were between 1.4 and 2.4 times higher than the drinking water limit. Lower condenser coil temperatures were correlated with an increased concentration of benzene in the product water. Environmental health professionals and engineers can integrate the results of this assessment to predict benzene concentrations in the product water and take appropriate health protective measures.

  17. Neutrophilic inflammatory response and oxidative stress in premenopausal women chronically exposed to indoor air pollution from biomass burning.

    Science.gov (United States)

    Banerjee, Anirban; Mondal, Nandan Kumar; Das, Debangshu; Ray, Manas Ranjan

    2012-04-01

    The possibility of inflammation and neutrophil activation in response to indoor air pollution (IAP) from biomass fuel use has been investigated. For this, 142 premenopausal, never-smoking women (median age, 34 years) who cook exclusively with biomass (wood, dung, crop wastes) and 126 age-matched control women who cook with cleaner fuel liquefied petroleum gas (LPG) were enrolled. The neutrophil count in blood and sputum was significantly higher (p enzyme-linked immunosorbent assay showed that they had 72%, 67%, and 54% higher plasma levels of the proinflammatory cytokines tumor necrosis factor-alpha, interleukin-6, and interleukin-12, respectively, and doubled neutrophil chemoattractant interleukin-8. Immunocytochemical study revealed significantly higher percentage of airway neutrophils expressing inducible nitric oxide synthase, while the serum level of nitric oxide was doubled in women who cooked with biomass. Spectrophotometric analysis documented higher myeloperoxidase activity in circulating neutrophils of biomass users, suggesting neutrophil activation. Flow cytometry showed excess generation of reactive oxygen species (ROS) by leukocytes of biomass-using women, whereas their erythrocytes contained a depleted level of antioxidant enzyme superoxide dismutase (SOD). Indoor air of biomass-using households had two to four times more particulate matter with diameters of <10 μm (PM(10)) and <2.5 μm (PM(2.5)) as measured by real-time laser photometer. After controlling potential confounders, rise in proinflammatory mediators among biomass users were positively associated with PM(10) and PM(2.5) in indoor air, suggesting a close relationship between IAP and neutrophil activation. Besides, the levels of neutrophil activation and inflammation markers were positively associated with generation of ROS and negatively with SOD, indicating a role of oxidative stress in mediating neutrophilic inflammatory response following chronic inhalation of biomass smoke.

  18. Implementing supercritical water oxidation technology in a lunar base environmental control/life support system

    Science.gov (United States)

    Meyer Sedej, M.

    1985-01-01

    A supercritical water oxidation system (SCWOS) offers several advantages for a lunar base environmental control/life support system (ECLSS) compared to an ECLSS based on Space Station technology. In supercritically heated water (630 K, 250 atm) organic materials mix freely with oxygen and undergo complete combustion. Inorganic salts lose solubility and precipitate out. Implementation of SCWOS can make an ECLSS more efficient and reliable by elimination of several subsystems and by reduction in potential losses of life support consumables. More complete closure of the total system reduces resupply requirements from the earth, a crucial cost item in maintaining a lunar base.

  19. Comparison of Short-Term Oxidation Behavior of Model and Commercial Chromia-Forming Ferritic Stainless Steels in Air with Water Vapor

    Energy Technology Data Exchange (ETDEWEB)

    Brady, Michael P [ORNL; Keiser, James R [ORNL; More, Karren Leslie [ORNL; Fayek, Mostafa [University of Manitoba, Canada; Walker, Larry R [ORNL; Meisner, Roberta Ann [ORNL; Anovitz, Lawrence {Larry} M [ORNL; Wesolowski, David J [ORNL; Cole, David R [ORNL

    2012-01-01

    A high-purity Fe-20Cr and commercial type 430 ferritic stainless steel were exposed at 700 and 800 C in dry air and air with 10% water vapor (wet air) and characterized by SEM, XRD, STEM, SIMS, and EPMA. The Fe-20Cr alloy formed a fast growing Fe-rich oxide scale at 700 C in wet air after 24 h exposure, but formed a thin chromia scale at 700 C in dry air and at 800 C in both dry air and wet air. In contrast, thin spinel + chromia base scales with a discontinuous silica subscale were formed on 430 stainless steel under all conditions studied. Extensive void formation was observed at the alloy-oxide interface for the Fe-20Cr in both dry and wet conditions, but not for the 430 stainless steel. The Fe-20Cr alloy was found to exhibit a greater relative extent of subsurface Cr depletion than the 430 stainless steel, despite the former's higher Cr content. Depletion of Cr in the Fe-20Cr after 24 h exposure was also greater at 700 C than 800 C. The relative differences in oxidation behavior are discussed in terms of the coarse alloy grain size of the high-purity Fe-20Cr material, and the effects of Mn, Si, and C on the oxide scale formed on the 430 stainless steel.

  20. Prediction of hydrodynamics and chemistry of confined turbulent methane-air flames with attention to formation of oxides of nitrogen

    Science.gov (United States)

    Elghobashi, S.; Spalding, D. B.; Srivatsa, S. K.

    1977-01-01

    A formulation of the governing partial differential equations for fluid flow and reacting chemical species in a tubular combustor is presented. A numerical procedure for the solution of the governing differential equations is described, and models for chemical equilibrium and chemical kinetics calculations are presented. The chemical equilibrium model is used to characterize the hydrocarbon reactions. The chemical kinetics model is used to predict the concentrations of the oxides of nitrogen. The combustor consists of a cylindrical duct of varying cross sections with concentric streams of gaseous fuel and air entering the duct at one end. Four sample cases with specified inlet and boundary conditions are considered, and the results are discussed

  1. Long Term Stability Investigation of Solid Oxide Electrolysis Cell with Infiltrated Porous YSZ Air Electrode Under High Current

    DEFF Research Database (Denmark)

    Veltzé, Sune; Ovtar, Simona; Simonsen, Søren Bredmose

    2015-01-01

    activity, due to high surface area of catalyst nano particles. Advantage of infiltration is also separate production of electrolyte backbone structure with good ionic connectivity and mechanical properties. With this study we present the results of a solid oxide cell with infiltrated porous yttria...... and the backbone, and perovskite catalyst material. Cobalt doped lanthanum nickelate was used as the perovskite catalyst due to its excellent performance. The cell was tested in steam electrolysis for at least 2000h. This initial test indicate that a stable air electrode was formed, and that the cell performance...

  2. Biological efficacy and toxic effect of emergency water disinfection process based on advanced oxidation technology.

    Science.gov (United States)

    Tian, Yiping; Yuan, Xiaoli; Xu, Shujing; Li, Rihong; Zhou, Xinying; Zhang, Zhitao

    2015-12-01

    An innovative and removable water treatment system consisted of strong electric field discharge and hydrodynamic cavitation based on advanced oxidation technologies was developed for reactive free radicals producing and waterborne pathogens eliminating in the present study. The biological efficacy and toxic effects of this advanced oxidation system were evaluated during water disinfection treatments. Bench tests were carried out with synthetic microbial-contaminated water, as well as source water in rainy season from a reservoir of Dalian city (Liaoning Province, China). Results showed that high inactivation efficiency of Escherichia coli (>5 log) could be obtained for synthetic contaminated water at a low concentration (0.5-0.7 mg L(-1)) of total oxidants in 3-10 s. The numbers of wild total bacteria (108 × 10(3) CFU mL(-1)) and total coliforms (260 × 10(2) MPN 100 mL(-1)) in source water greatly reduced to 50 and 0 CFU mL(-1) respectively after treated by the advanced oxidation system, which meet the microbiological standards of drinking water, and especially that the inactivation efficiency of total coliforms could reach 100%. Meanwhile, source water qualities were greatly improved during the disinfection processes. The values of UV254 in particular were significantly reduced (60-80%) by reactive free radicals. Moreover, the concentrations of possible disinfection by-products (formaldehyde and bromide) in treated water were lower than detection limits, indicating that there was no harmful effect on water after the treatments. These investigations are helpful for the ecotoxicological studies of advanced oxidation system in the treatments of chemical polluted water or waste water. The findings of this work suggest that the developed water treatment system is ideal in the acute phases of emergencies, which also could offer additional advantages over a wide range of applications in water pollution control.

  3. Determination of the Clean Air Delivery Rate (CADR) of Photocatalytic Oxidation (PCO) Purifiers for Indoor Air Pollutants Using a Closed-Loop Reactor. Part I: Theoretical Considerations.

    Science.gov (United States)

    Dumont, Éric; Héquet, Valérie

    2017-03-06

    This study demonstrated that a laboratory-scale recirculation closed-loop reactor can be an efficient technique for the determination of the Clean Air Delivery Rate (CADR) of PhotoCatalytic Oxidation (PCO) air purification devices. The recirculation closed-loop reactor was modeled by associating equations related to two ideal reactors: one is a perfectly mixed reservoir and the other is a plug flow system corresponding to the PCO device itself. Based on the assumption that the ratio between the residence time in the PCO device and the residence time in the reservoir τP/τR tends to 0, the model highlights that a lab closed-loop reactor can be a suitable technique for the determination of the efficiency of PCO devices. Moreover, if the single-pass removal efficiency is lower than 5% of the treated flow rate, the decrease in the pollutant concentration over time can be characterized by a first-order decay model in which the time constant is proportional to the CADR. The limits of the model are examined and reported in terms of operating conditions (experiment duration, ratio of residence times, and flow rate ranges).

  4. Removal of salicylic acid on perovskite-type oxide LaFeO3 catalyst in catalytic wet air oxidation process.

    Science.gov (United States)

    Yang, Min; Xu, Aihua; Du, Hongzhang; Sun, Chenglin; Li, Can

    2007-01-02

    It has been found that salicylic acid can be removal effectively at the lower temperature of 140 degrees C on perovskite-type oxide LaFeO3 catalyst in the catalytic wet air oxidation (CWAO) process. Under the same condition, the activities for the CWAO of phenol, benzoic acid and sulfonic salicylic acid have been also investigated. The results indicated that, with compared to the very poor activities for phenol and benzoic acid, the activities for salicylic acid and sulfonic salicylic acid were very high, which are attributed to their same intramolecular H-bonding structures. With the role of hard acidity of intramolecular H-bonding, salicylic acid and sulfonic salicylic acid can be adsorbed effectively on the basic center of LaFeO3 catalyst and are easy to take place the total oxidation reaction. However, at temperatures higher than 140 degrees C, the intramolecular H-bonding structure of salicylic acid was destroyed and the activities at 160 and 180 degrees C decreased greatly, which confirms further the key role of intramolecular H-bonding in the CWAO. Moreover, the LaFeO3 catalyst also indicated a superior stability of activity and structure in CWAO of salicylic acid.

  5. Study on the isothermal oxidation behavior in air of Ti3AlC2 sintered by hot pressing

    Institute of Scientific and Technical Information of China (English)

    XU; Xuewen; LI; Yangxian; MEI; Bingchu; ZHU; Jiaoqun; LIU; Heyan

    2006-01-01

    The isothermal oxidation behavior at 900―1300℃ for 20 h in air of bulk Ti3AlC2 with 2.8 wt% TiC sintered by means of hot pressing was investigated in the work. The isothermal oxidation behavior generally followed a parabolic rate law. The parabolic rate constants increased from 1.39×10-10 kg2·m-4·s-1 at 900℃ to 5.56×10-9 kg2·m-4·s-1 at 1300℃. The calculated activation energy was 136.45 kJ/mol. It was demonstrated that Ti3AlC2 had excellent oxidation resistance due to the continuous, dense and adhesive protect scales consisted of a mass of α-Al2O3 and a little of TiO2 and/or Al2TiO5. In principle, the oxide scale was grown by the inward diffusion of O2- and the outward diffusion of Ti4+ and Al3+. The rapid outward diffusion of cations usually resulted in the formation of cracks, gaps, and holes.

  6. Assessment of methane emission and oxidation at Air Hitam Landfill site cover soil in wet tropical climate.

    Science.gov (United States)

    Abushammala, Mohammed F M; Basri, Noor Ezlin Ahmad; Elfithri, Rahmah

    2013-12-01

    Methane (CH₄) emissions and oxidation were measured at the Air Hitam sanitary landfill in Malaysia and were modeled using the Intergovernmental Panel on Climate Change waste model to estimate the CH₄ generation rate constant, k. The emissions were measured at several locations using a fabricated static flux chamber. A combination of gas concentrations in soil profiles and surface CH₄ and carbon dioxide (CO₂) emissions at four monitoring locations were used to estimate the CH₄ oxidation capacity. The temporal variations in CH₄ and CO₂ emissions were also investigated in this study. Geospatial means using point kriging and inverse distance weight (IDW), as well as arithmetic and geometric means, were used to estimate total CH₄ emissions. The point kriging, IDW, and arithmetic means were almost identical and were two times higher than the geometric mean. The CH₄ emission geospatial means estimated using the kriging and IDW methods were 30.81 and 30.49 gm(−2) day(−1), respectively. The total CH₄ emissions from the studied area were 53.8 kg day(−1). The mean of the CH₄ oxidation capacity was 27.5 %. The estimated value of k is 0.138 year(−1). Special consideration must be given to the CH₄ oxidation in the wet tropical climate for enhancing CH₄ emission reduction.

  7. Wet air oxidation of formic acid using nanoparticle-modified polysulfone hollow fibers as gas-liquid contactors.

    Science.gov (United States)

    Hogg, Seth R; Muthu, Satish; O'Callaghan, Michael; Lahitte, Jean-Francois; Bruening, Merlin L

    2012-03-01

    Catalytic wet air oxidation (CWAO) using membrane contactors is attractive for remediation of aqueous pollutants, but previous studies of even simple reactions such as formic acid oxidation required multiple passes through tubular ceramic membrane contactors to achieve high conversion. This work aims to increase single-pass CWAO conversions by using polysulfone (PS) hollow fibers as contactors to reduce diffusion distances in the fiber lumen. Alternating adsorption of polycations and citrate-stabilized platinum colloids in fiber walls provides catalytically active PS hollow fibers. Using a single PS fiber, 50% oxidation of a 50 mM formic acid feed solution results from a single pass through the fiber lumen (15 cm length) with a solution residence time of 40 s. Increasing the number of PS fibers to five while maintaining the same volumetric flow rate leads to over 90% oxidation, suggesting that further scale up in the number of fibers will facilitate high single pass conversions at increased flow rates. The high conversion compared to prior studies with ceramic fibers stems from shorter diffusion distances in the fiber lumen. However, the activity of the Pt catalyst is 20-fold lower than in previous ceramic fibers. Focusing the Pt deposition near the fiber lumen and limiting pore wetting to this region might increase the activity of the catalyst.

  8. One-dimensional analytical model for oxide thin film growth on Ti metal layers during laser heating in air

    Science.gov (United States)

    Jiménez Pérez, J. L.; Sakanaka, P. H.; Algatti, M. A.; Mendoza-Alvarez, J. G.; Cruz Orea, A.

    2001-05-01

    This paper presents the theoretical and experimental results for oxide thin film growth on titanium films previously deposited over glass substrate. Ti films of thickness 0.1 μm were heated by Nd:YAG laser pulses in air. The oxide tracks were created by moving the samples with a constant speed of 2 mm/s, under the laser action. The micro-topographic analysis of the tracks was performed by a microprofiler. The results taken along a straight line perpendicular to the track axis revealed a Gaussian profile that closely matches the laser's spatial mode profile, indicating the effectiveness of the surface temperature gradient on the film's growth process. The sample's micro-Raman spectra showed two strong bands at 447 and 612 cm -1 associated with the TiO 2 structure. This is a strong indication that thermo-oxidation reactions took place at the Ti film surface that reached an estimated temperature of 1160 K just due to the action of the first pulse. The results obtained from the numerical integration of the analytical equation which describes the oxidation rate (Wagner equation) are in agreement with the experimental data for film thickness in the high laser intensity region. This shows the partial accuracy of the one-dimensional model adopted for describing the film growth rate.

  9. Lean VOC-Air Mixtures Catalytic Treatment: Cost-Benefit Analysis of Competing Technologies

    Directory of Open Access Journals (Sweden)

    Gabriele Baldissone

    2017-06-01

    Full Text Available Various processing routes are available for the treatment of lean VOC-air mixtures, and a cost-benefit analysis is the tool we propose to identify the most suitable technology. Two systems have been compared in this paper, namely a “traditional” plant, with a catalytic fixed-bed reactor with a heat exchanger for heat recovery purposes, and a “non-traditional” plant, with a catalytic reverse-flow reactor, where regenerative heat recovery may be achieved thanks to the periodical reversal of the flow direction. To be useful for decisions-making, the cost-benefit analysis must be coupled to the reliability, or availability, analysis of the plant. Integrated Dynamic Decision Analysis is used for this purpose as it allows obtaining the full set of possible sequences of events that could result in plant unavailability, and, for each of them, the probability of occurrence is calculated. Benefits are thus expressed in terms of out-of-services times, that have to be minimized, while the costs are expressed in terms of extra-cost for maintenance activities and recovery actions. These variable costs must be considered together with the capital (fixed cost required for building the plant. Results evidenced the pros and cons of the two plants. The “traditional” plant ensures a higher continuity of services, but also higher operational costs. The reverse-flow reactor-based plant exhibits lower operational costs, but a higher number of protection levels are needed to obtain a similar level of out-of-service. The quantification of risks and benefits allows the stakeholders to deal with a complete picture of the behavior of the plants, fostering a more effective decision-making process. With reference to the case under study and the relevant operational conditions, the regenerative system was demonstrated to be more suitable to treat lean mixtures: in terms of time losses following potential failures the two technologies are comparable (Fixed bed

  10. Study on Water Treatment Technology of Central Air Conditioner%中央空调水处理研究

    Institute of Scientific and Technical Information of China (English)

    黎代华

    2015-01-01

    随着国家提倡节能减排,空调系统的节能越发引起人们的重视。文章通过介绍南博中央空调水处理,分析中央空调水系统中存在的问题,通过中央空调水处理提高中央空调制冷效率,从而实现节能的效果。%Due to the advocation of “energy saving and emission reduction” of Chinese government,more and more people pay attention to air conditioners energy conservation. This article analyzes the problems of central air conditioner water system,and discovers that the central air conditioner refrigeration efficiency will be improved through water treatment technology, and plenty of energy will be saved.

  11. Fuel Savings and Emission Reductions from Next-Generation Mobile Air Conditioning Technology in India

    Energy Technology Data Exchange (ETDEWEB)

    Chaney, L.; Thundiyil, K.; Andersen, S.; Chidambaram, S.; Abbi, Y. P.

    2007-01-01

    Up to 19.4% of vehicle fuel consumption in India is devoted to air conditioning (A/C). Indian A/C fuel consumption is almost four times the fuel penalty in the United States and close to six times that in the European Union because India's temperature and humidity are higher and because road congestion forces vehicles to operate inefficiently. Car A/C efficiency in India is an issue worthy of national attention considering the rate of increase of A/C penetration into the new car market, India's hot climatic conditions and high fuel costs. Car A/C systems originally posed an ozone layer depletion concern. Now that industrialized and many developing countries have moved away from ozone-depleting substances per Montreal Protocol obligations, car A/C impact on climate has captured the attention of policy makers and corporate leaders. Car A/C systems have a climate impact from potent global warming potential gas emissions and from fuel used to power the car A/Cs. This paper focuses on car A/C fuel consumption in the context of the rapidly expanding Indian car market and how new technological improvements can result in significant fuel savings and consequently, emission reductions. A 19.4% fuel penalty is associated with A/C use in the typical Indian passenger car. Car A/C fuel use and associated tailpipe emissions are strong functions of vehicle design, vehicle use, and climate conditions. Several techniques: reducing thermal load, improving vehicle design, improving occupants thermal comfort design, improving equipment, educating consumers on impacts of driver behaviour on MAC fuel use, and others - can lead to reduced A/C fuel consumption.

  12. Technical and economic assessment of fluidized bed augmented compressed air energy-storage system. Volume II. Introduction and technology assessment

    Energy Technology Data Exchange (ETDEWEB)

    Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

    1981-09-01

    The results are described of a study subcontracted by PNL to the United Technologies Research Center on the engineering feasibility and economics of a CAES concept which uses a coal fired, fluidized bed combustor (FBC) to heat the air being returned from storage during the power production cycle. By burning coal instead of fuel oil, the CAES/FBC concept can completely eliminate the dependence of compressed air energy storage on petroleum fuels. The results of this assessment effort are presented in three volumes. Volume II presents a discussion of program background and an in-depth coverage of both fluid bed combustion and turbomachinery technology pertinent to their application in a CAES power plant system. The CAES/FBC concept appears technically feasible and economically competitive with conventional CAES. However, significant advancement is required in FBC technology before serious commercial commitment to CAES/FBC can be realized. At present, other elements of DOE, industrial groups, and other countries are performing the required R and D for advancement of FBC technology. The CAES/FBC will be reevaluated at a later date when FBC technology has matured and many of the concerns now plaguing FBC are resolved. (LCL)

  13. Sistem Kendali Penyaluran Air Pendingin (Water Chiller) Pada Proses Pencetakan Sarung Tangan Latex (Aplikasi PT. Medisafe Technologies)

    OpenAIRE

    Gultom, Linando F.

    2010-01-01

    Dalam dunia industri banyak digunakan peralatan–peralatan yang sistem kerjanya dikendalikan secara otomatis dalam melakukan proses produksi. Dalam hal ini untuk mengolah bahan baku menjadi bahan jadi (produk) yang sesuai dengan permintaan kosumen berdasarkan mutu produk yang diinginkan. PT. Medisafe Technologies merupakan perusahaan yang bergerak dibidang pembuatan sarung tangan. Dalam pencetakan sarung tangan yang dimasukkan dalam tangki latex yang dilapisi air sebagai pendingin yang dialir...

  14. Research on Emissions, Air quality, Climate, and Cooking Technologies in Northern Ghana (REACCTING): study rationale and protocol

    OpenAIRE

    Dickinson, Katherine L.; Kanyomse, Ernest; Piedrahita, Ricardo; Coffey, Evan; Rivera, Isaac J; Adoctor, James; Alirigia, Rex; Muvandimwe, Didier; Dove, MacKenzie; Dukic, Vanja; Mary H Hayden; Diaz-Sanchez, David; Abisiba, Adoctor Victor; Anaseba, Dominic; Hagar, Yolanda

    2015-01-01

    Background Cooking over open fires using solid fuels is both common practice throughout much of the world and widely recognized to contribute to human health, environmental, and social problems. The public health burden of household air pollution includes an estimated four million premature deaths each year. To be effective and generate useful insight into potential solutions, cookstove intervention studies must select cooking technologies that are appropriate for local socioeconomic conditio...

  15. Airspace Systems Program: Next Generation Air Transportation System Concepts and Technology Development FY2010 Project Plan Version 3.0

    Science.gov (United States)

    Kopardekar, Parimal H.

    2010-01-01

    This document describes the FY2010 plan for the management and execution of the Next Generation Air Transportation System (NextGen) Concepts and Technology Development (CTD) Project. The document was developed in response to guidance from the Airspace Systems Program (ASP), as approved by the Associate Administrator of the Aeronautics Research Mission Directorate (ARMD), and from guidelines in the Airspace Systems Program Plan. Congress established the multi-agency Joint Planning and Development Office (JPDO) in 2003 to develop a vision for the 2025 Next Generation Air Transportation System (NextGen) and to define the research required to enable it. NASA is one of seven agency partners contributing to the effort. Accordingly, NASA's ARMD realigned the Airspace Systems Program in 2007 to "directly address the fundamental research needs of the Next Generation Air Transportation System...in partnership with the member agencies of the JPDO." The Program subsequently established two new projects to meet this objective: the NextGen-Airspace Project and the NextGen-Airportal Project. Together, the projects will also focus NASA s technical expertise and world-class facilities to address the question of where, when, how and the extent to which automation can be applied to moving aircraft safely and efficiently through the NAS and technologies that address optimal allocation of ground and air technologies necessary for NextGen. Additionally, the roles and responsibilities of humans and automation influence in the NAS will be addressed by both projects. Foundational concept and technology research and development begun under the NextGen-Airspace and NextGen-Airportal projects will continue. There will be no change in NASA Research Announcement (NRA) strategy, nor will there be any change to NASA interfaces with the JPDO, Federal Aviation Administration (FAA), Research Transition Teams (RTTs), or other stakeholders

  16. Research on Emissions, Air quality, Climate, and Cooking Technologies in Northern Ghana (REACCTING): study rationale and protocol.

    Science.gov (United States)

    Dickinson, Katherine L; Kanyomse, Ernest; Piedrahita, Ricardo; Coffey, Evan; Rivera, Isaac J; Adoctor, James; Alirigia, Rex; Muvandimwe, Didier; Dove, MacKenzie; Dukic, Vanja; Hayden, Mary H; Diaz-Sanchez, David; Abisiba, Adoctor Victor; Anaseba, Dominic; Hagar, Yolanda; Masson, Nicholas; Monaghan, Andrew; Titiati, Atsu; Steinhoff, Daniel F; Hsu, Yueh-Ya; Kaspar, Rachael; Brooks, Bre'Anna; Hodgson, Abraham; Hannigan, Michael; Oduro, Abraham Rexford; Wiedinmyer, Christine

    2015-02-12

    Cooking over open fires using solid fuels is both common practice throughout much of the world and widely recognized to contribute to human health, environmental, and social problems. The public health burden of household air pollution includes an estimated four million premature deaths each year. To be effective and generate useful insight into potential solutions, cookstove intervention studies must select cooking technologies that are appropriate for local socioeconomic conditions and cooking culture, and include interdisciplinary measurement strategies along a continuum of outcomes. REACCTING (Research on Emissions, Air quality, Climate, and Cooking Technologies in Northern Ghana) is an ongoing interdisciplinary randomized cookstove intervention study in the Kassena-Nankana District of Northern Ghana. The study tests two types of biomass burning stoves that have the potential to meet local cooking needs and represent different "rungs" in the cookstove technology ladder: a locally-made low-tech rocket stove and the imported, highly efficient Philips gasifier stove. Intervention households were randomized into four different groups, three of which received different combinations of two improved stoves, while the fourth group serves as a control for the duration of the study. Diverse measurements assess different points along the causal chain linking the intervention to final outcomes of interest. We assess stove use and cooking behavior, cooking emissions, household air pollution and personal exposure, health burden, and local to regional air quality. Integrated analysis and modeling will tackle a range of interdisciplinary science questions, including examining ambient exposures among the regional population, assessing how those exposures might change with different technologies and behaviors, and estimating the comparative impact of local behavior and technological changes versus regional climate variability and change on local air quality and health outcomes

  17. Removal of organic micropollutants in surface and groundwater using advanced oxidation technologies

    Energy Technology Data Exchange (ETDEWEB)

    Urkiaga, A.; Barcena, L.; Fuentes, L. de las [GAIKER Technological Centre, Parque Tecnologico, Zamudio (Bizkaia) (Spain)

    2003-07-01

    Today more than ever, there is a public concern about the importance of having water of proven quality, as urban and industrial development are highly dependent on an abundant and safe water supply. Traces of organic micropollutants have been found in natural and drinking water. Some of these water pollutants have teratogenic, mutagenic or carcinogenic effects even in minimal quantities (ppb) so actual regulations, the water framework directive 2000/60/CE and the drinking water directive (98/83/CE), have established new and more stringent standards. Emerging technologies as the advanced oxidation processes (AOPs) are expanding as very promising technologies to remove these compounds and consequently to obtain water of high quality. In this work, several compounds representing different micropollutant groups were selected: VOCs (TCE), gasoline derivatives (MTBE), pesticides and other endocrine disruptors (PCBs and Bisphenol-A). The viability of using advanced oxidation processes to eliminate these different compounds was evaluated. The efficiency of the removal has been proven, however to fulfil with the legislation limits a polishing step would be needed in most cases. Although very high removals have been obtained for the different compounds, mineralisation rates have been quite lower and intermediate compounds have been detected. Consequently, higher mineralisation rates and a more profusely study of the effects of the generated intermediates would be needed. (orig.)

  18. Fully solution-processed zinc oxide MIS capacitors by ultrasonic spray pyrolysis in air ambient

    Directory of Open Access Journals (Sweden)

    Miguel A. Dominguez

    2017-06-01

    Full Text Available In this work, the fabrication and characterization of fully solution-processed zinc oxide metal–insulator–semiconductor (MIS capacitors by ultrasonic spray pyrolysis (USP are presented. Fluorine tin oxide by USP was used as transparent electrode, while spin-on glass by spin-coating was used as dielectric and zinc oxide by USP was used as active layer. Also, the zinc oxide film was characterized using photoluminescence spectroscopy, X-ray diffraction and Fourier transform infrared spectroscopy. The MIS capacitors were fabricated over glass slides and were highly transparent in the visible range, which makes their use feasible in transparent electronics. Employing capacitance–voltage and current–voltage measurements, the MIS capacitors were characterized.

  19. Ethylene Oxide Commerical Sterilization and Fumigation Operations National Emission Standards for Hazardous Air Pollutants (NESHAP)

    Science.gov (United States)

    The purpose of this document is to provide implementation materials to assist in conducting complete and efficient inspections at ethylene oxide commercial sterilization and fumigation operations to determine compliance with the NESHAP

  20. Fact Sheets: Final Air Toxics Rules for Ethylene Oxide Emissions from Commercial Sterilization and Fumigation Operations

    Science.gov (United States)

    This page contains November 1994 and November 1999 fact sheets with information regarding the Final Ethylene Oxide Emissions Standards for Sterilization Facilities. These documents contain answers to common questions for this NESHAP

  1. The Oxidation Behavior of Vanadium Alloys in Air at Elevated Temperature

    Institute of Scientific and Technical Information of China (English)

    CHENJiming; XUYing; XUZengyu

    2001-01-01

    Vanadium alloy is one of the most important candidate structural materials for a fusion reactor. Its main advantages over other candidates are its low activity feature and feasible properties at high temperature. However, vanadium is easily oxidized at high temperature to form a non-protective surface film of V2O5. Oxygen concentration would thus get high and the properties get worse in not only the loss of the ductility but also the enhanced hydrogen embrittlement by the oxidation.

  2. High performance air electrode for solid oxide regenerative fuel cells fabricated by infiltration of nano-catalysts

    Science.gov (United States)

    Lee, Sung-il; Kim, Jeonghee; Son, Ji-Won; Lee, Jong-Ho; Kim, Byung-Kook; Je, Hae-June; Lee, Hae-Weon; Song, Huesup; Yoon, Kyung Joong

    2014-03-01

    A high performance air electrode fabricated by infiltration of highly active nano-catalysts into a porous scaffold is demonstrated for high-temperature solid oxide regenerative fuel cells (SORFCs). The nitrate precursor solution for Sm0.5Sr0.5CoO3 (SSC) catalyst is impregnated into a porous La0.6Sr0.4Co0.2Fe0.8O3 (LSCF)-gadolinia-doped ceria (GDC) composite backbone, and extremely fine SSC nano-particles are uniformly synthesized by in-situ crystallization at the initial stage of SORFC operation via homogeneous nucleation induced by urea decomposition. The SSC nano-catalysts are in the size range of 40-80 nm and stable against coarsening upon the SORFC operation at 750 °C. The electrochemical performance is significantly improved by incorporation of SSC nano-catalysts in both power generation and hydrogen production modes. Systematic analysis on the impedance spectra reveals that the surface modification of the air electrode with nano-catalysts remarkably accelerates the chemical surface exchange reactions for both O2 reduction and O2- oxidation, which are the major limiting processes for SORFC performance.

  3. Association of air pollution sources and aldehydes with biomarkers of blood coagulation, pulmonary inflammation, and systemic oxidative stress.

    Science.gov (United States)

    Altemose, Brent; Robson, Mark G; Kipen, Howard M; Ohman Strickland, Pamela; Meng, Qingyu; Gong, Jicheng; Huang, Wei; Wang, Guangfa; Rich, David Q; Zhu, Tong; Zhang, Junfeng

    2016-07-20

    Using data collected before, during, and after the 2008 Summer Olympic Games in Beijing, this study examines associations between biomarkers of blood coagulation (vWF, sCD62P and sCD40L), pulmonary inflammation (EBC pH, EBC nitrite, and eNO), and systemic oxidative stress (urinary 8-OHdG) with sources of air pollution identified utilizing principal component analysis and with concentrations of three aldehydes of health concern. Associations between the biomarkers and the air pollution source types and aldehydes were examined using a linear mixed effects model, regressing through seven lag days and controlling for ambient temperature, relative humidity, gender, and day of week for the biomarker measurements. The biomarkers for pulmonary inflammation, particularly EBC pH and eNO, were most consistently associated with vehicle and industrial combustion, oil combustion, and vegetative burning. The biomarkers for blood coagulation, particularly vWF and sCD62p, were most consistently associated with oil combustion. Systemic oxidative stress biomarker (8-OHdG) was most consistently associated with vehicle and industrial combustion. The associations of the biomarkers were generally not significant or consistent with secondary formation of pollutants and with the aldehydes. The findings support policies to control anthropogenic pollution sources rather than natural soil or road dust from a cardio-respiratory health standpoint.Journal of Exposure Science and Environmental Epidemiology advance online publication, 20 July 2016; doi:10.1038/jes.2016.38.

  4. Catalytic wet air oxidation of coke-plant wastewater on ruthenium-based eggshell catalysts in a bubbling bed reactor.

    Science.gov (United States)

    Yang, M; Sun, Y; Xu, A H; Lu, X Y; Du, H Z; Sun, C L; Li, C

    2007-07-01

    Catalytic wet air of coke-plant wastewater was studied in a bubbling bed reactor. Two types of supported Ru-based catalysts, eggshell and uniform catalysts, were employed. Compared with the results in the wet air oxidation of coke-plant wastewater, supported Ru uniform catalysts showed high activity for chemical oxygen demand (COD) and ammonia/ammonium compounds (NH3-N) removal at temperature of 250 degrees C and pressure of 4.8 MPa, and it has been demonstrated that the catalytic activity of uniform catalyst depended strongly on the distribution of active sites of Ru on catalyst. Compared to the corresponding uniform catalysts with the same Ru loading (0.25 wt.% and 0.1 wt.%, respectively), the eggshell catalysts showed higher activities for CODcr removal and much higher activities for NH3-N degradation. The high activity of eggshell catalyst for treatment of coke-plant wastewater can be attributed to the higher density of active Ru sites in the shell layer than that of the corresponding uniform catalyst with the same Ru loading. It has been also evidenced that the active Ru sites in the internal core of uniform catalyst have very little or no contribution to CODcr and NH3-N removal in the total oxidation of coke-plant wastewater.

  5. Treatment of refractory nano-filtration reject from a tannery using Pd-catalyzed wet air oxidation.

    Science.gov (United States)

    Tripathi, Pranav K; Rao, Nageswara N; Chauhan, Chetan; Pophali, Girish R; Kashyap, Sanjay M; Lokhande, Satish K; Gan, Lihua

    2013-10-15

    We attempted catalytic wet air oxidation (CWAO) of nanofiltration (NF)-reject using Pd based catalyst viz., Pd/activated charcoal (AC) and PdCl2 with the objective of degradation of refractory organic pollutants. Refractory organic pollutants in NF-reject before and after WAO and CWAO were confirmed by GC-MS analysis. Experiments were conducted to investigate the effects of temperature, catalyst dosage and air partial pressure on the rate of removal of total organic carbon (TOC). The reaction kinetics can be conveniently described by considering two-stage first order kinetics. The use of Pd/AC afforded 85% TOC removal, the corresponding rate constant (k) was 2.90 ± 0.075 × 10(-3)min(-1) (Pd/AC, 100mg/L; T, 473.15K; Pair, 0.69 MPa). On the other hand, 75% TOC was removed with k=2.31 ± 0.075 × 10(-3)min(-1) using Pd(2+) catalyst (Pd(2+), 16.66 mg/L; T, 473.15K; Pair, 0.69 MPa). The observed rate of mineralization under Pd-catalyzed conditions was significantly higher than that of the uncatalyzed oxidation (41%) under the similar experimental conditions. Catalyst stability experiments were performed and TEM, SEM, XRD, Raman and XPS characterization data collected. Despite some morphological transformation of support, Pd catalyst was stable under CWAO conditions.

  6. The Arteries of Global Trade: Industrial Restructuring and Technological Change in the Transatlantic Air Cargo Industry

    Science.gov (United States)

    Schwarz, Guido

    2010-01-01

    Air cargo enjoys a special importance: together with maritime transport it is the backbone of global trade and is indispensable for contemporary globalization. Air transport is the only mode that combines worldwide reach with high speed. Nonetheless there is a dearth of geographic research that analyzes the current restructuring affecting the air…

  7. Degradation of the insecticide propoxur by electrochemical advanced oxidation processes using a boron-doped diamond/air-diffusion cell.

    Science.gov (United States)

    Guelfi, Diego Roberto Vieira; Gozzi, Fábio; Sirés, Ignasi; Brillas, Enric; Machulek, Amílcar; de Oliveira, Silvio César

    2017-03-01

    A solution with 0.38 mM of the pesticide propoxur (PX) at pH 3.0 has been comparatively treated by electrochemical oxidation with electrogenerated H2O2 (EO-H2O2), electro-Fenton (EF), and photoelectro-Fenton (PEF). The trials were carried out with a 100-mL boron-doped diamond (BDD)/air-diffusion cell. The EO-H2O2 process had the lowest oxidation ability due to the slow reaction of intermediates with (•)OH produced from water discharge at the BDD anode. The EF treatment yielded quicker mineralization due to the additional (•)OH formed between added Fe(2+) and electrogenerated H2O2. The PEF process was the most powerful since it led to total mineralization by the combined oxidative action of hydroxyl radicals and UVA irradiation. The PX decay agreed with a pseudo-first-order kinetics in EO-H2O2, whereas in EF and PEF, it obeyed a much faster pseudo-first-order kinetics followed by a much slower one, which are related to the oxidation of its Fe(II) and Fe(III) complexes, respectively. EO-H2O2 showed similar oxidation ability within the pH range 3.0-9.0. The effect of current density and Fe(2+) and substrate contents on the performance of the EF process was examined. Two primary aromatic products were identified by LC-MS during PX degradation.

  8. SITE EMERGING TECHNOLOGY SUMMARY: INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

    Science.gov (United States)

    In a recently completed test program, bench-scale laboratory studies at Arizona State University (ASU) in Tempe, AZ, and pilot-scale studies in a simulated field test situation at Zentox Corp in Ocala, FL, were performed to evaluate the integration of gas-solid ultraviolet (UV) p...

  9. Changes in coal structure accompanying the formation of regenerated humic acids during air oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Calemma, V.; Iwanski, P.; Rausa, R.; Girardi, E. (Eniricerche S.p.A., Milan (Italy))

    1994-05-01

    Dry-phase oxidation of two subbituminous coals and a lignite was carried out in a fluidized bed reactor at 200[degree]C, at different oxygen partial pressures and reaction times up to 4 h. The formation and evolution of various oxygenated functional groups (ester, carboxyl, ketone and hydroxyl) was investigated by FT-i.r. spectroscopy using a curve-resolving procedure and acetylation of coal samples. The development of alkali solubility of the coal as a function of reaction time was studied and the average molecular weight of regenerated humic acids (RHA) extracted from the oxidized coal was determined. The lower molecular weight of RHA extracted from highly oxidized coal samples suggests that besides the build-up of various oxygenated functional groups, the development of alkali solubility also results from concomitant 'depolymerization' of the coal network. The latter may occur through oxidation of aliphatic cross-links and formation of ester groups hydrolysable in basic solution. The FT-i.r. results were correlated with the development of alkali solubility. Some oxidation pathways are proposed. 49 refs., 11 figs., 1 tab.

  10. TiO2光催化氧化技术的研究与发展%Research Progress in TiO2 Photocatalytic Oxidation Technology

    Institute of Scientific and Technical Information of China (English)

    肖俊霞; 吴贤格

    2011-01-01

    The mechanism of TiO2 photocatalytic reaction was described briefly. The ways of improving TiO2 photocatalytic activity including metal ions doping, noble metals surface deposition,nonmetals doping, co-doping, semiconductor coupling, surface photosensitization and external field coupling were introduced emphatically. The application of TiO2 photocatalytic oxidation technology were summarized including oxidation/reduction treatment to pollutants in water, oxidation treatment to volatile organic compounds in air and sterilization. Besides, based on the actual problems on TiO2 photocatalytic oxidation technology it was proposed that the mechanism research of kinetics and thermodynamics of pollutants degradation and the macroscopical reaction kinetics of photocatalytic reactor was its further development.%简述了TiO2光催化反应的机理,重点介绍了金属离子掺杂、贵金属表面沉积、非金属元素掺杂、共掺杂、半导体复合、表面光敏化及外场耦合等提高TiO2光催化性能的途径,总结了TiO2光催化氧化技术对水中污染物的氧化/还原处理、对大气中挥发性有机物的氧化处理及在抗菌消毒等方面的应用,并针对TiO2光催化氧化技术研究方面存在的问题,提出其未来的发展方向是污染物降解的动力学与热力学以及光催化反应器的宏观反应动力学的机理研究.

  11. EPA-developed, patented technologies related to air quality that are available for licensing

    Data.gov (United States)

    U.S. Environmental Protection Agency — Under the Federal Technology Transfer Act (FTTA), Federal Agencies can patent inventions developed during the course of research. These technologies can then be...

  12. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - PHOTOACOUSTIC SPECTROPHOTOMATER INNOVA AIR TECH INSTRUMENTS MODEL 1312 MULTI-GAS MONITOR

    Science.gov (United States)

    The U.S. Environmental Protection Agency, Through the Environmental Technology Verification Program, is working to accelerate the acceptance and use of innovative technologies that improve the way the United States manages its environmental problems. This report documents demons...

  13. Performance analysis of the T-DOC® air-charged catheters: An alternate technology for urodynamics.

    Science.gov (United States)

    Couri, Bruna M; Bitzos, Stephanie; Bhardwaj, Deepak; Lockhart, Emily; Yue, Andy; Goping, Ing

    2017-07-17

    Urodynamics (UDS) is widely used for the diagnosis of lower urinary tract dysfunction. Air-Charged catheters (ACC), one of the newer technologies for UDS pressure recording, has been adopted in growing numbers around the world for the past 15 years. Currently, there is a lack of published studies characterizing specific performance of the ACC. Since linearity, hysteresis, pressure drift, and frequency response are important components in characterizing accuracy for catheter-manometer systems; this study aimed to assess these four aspects in ACC. A total of 180 T-DOC® ACC were used in three different laboratory settings to assess pressure linearity and hysteresis (15 dual-sensor vesical and urethral and 30 single-sensor abdominal), pressure drift over 2 h (115 single-sensor), and frequency response (20 single-sensor). Data are presented as mean ± standard deviation. ACC showed linearity of 0.99 ± 0.01, 0.99 ± 0.01, and 1.01 ± 0.01; and hysteresis of 0.57 ± 0.3%, 0.76 ± 0.48%, and 1 ± 0.89% for the abdominal, vesical, and urethral sensors, respectively. A pressure drift of 2.2 ± 1.4% at 1 h and 4.4 ± 2.5% at 2 h were observed when compared to baseline pressures. The catheters did not show any amplification factor during the sweep from 1 to 30 Hz, and recorded signals up to 5 Hz attenuating higher frequency signals. In this study the T-DOC® ACC showed a linear performance with minimal hysteresis associated with acceptable pressure drift, and adequate frequency response to capture clinically relevant pressures. The accurate results observed in this study suggest that these catheters are technically suitable to be used as a measuring instrument for UDS. © 2017 Wiley Periodicals, Inc.

  14. System and Propagation Availability Analysis for NASA's Advanced Air Transportation Technologies

    Science.gov (United States)

    Ugweje, Okechukwu C.

    2000-01-01

    This report summarizes the research on the System and Propagation Availability Analysis for NASA's project on Advanced Air Transportation Technologies (AATT). The objectives of the project were to determine the communication systems requirements and architecture, and to investigate the effect of propagation on the transmission of space information. In this report, results from the first year investigation are presented and limitations are highlighted. To study the propagation links, an understanding of the total system architecture is necessary since the links form the major component of the overall architecture. This study was conducted by way of analysis, modeling and simulation on the system communication links. The overall goals was to develop an understanding of the space communication requirements relevant to the AATT project, and then analyze the links taking into consideration system availability under adverse atmospheric weather conditions. This project began with a preliminary study of the end-to-end system architecture by modeling a representative communication system in MATLAB SIMULINK. Based on the defining concepts, the possibility of computer modeling was determined. The investigations continue with the parametric studies of the communication system architecture. These studies were also carried out with SIMULINK modeling and simulation. After a series of modifications, two end-to-end communication links were identified as the most probable models for the communication architecture. Link budget calculations were then performed in MATHCAD and MATLAB for the identified communication scenarios. A remarkable outcome of this project is the development of a graphic user interface (GUI) program for the computation of the link budget parameters in real time. Using this program, one can interactively compute the link budget requirements after supplying a few necessary parameters. It provides a framework for the eventual automation of several computations

  15. Simulation Analysis of Sludge Disposal and Volatile Fatty Acids Production from Gravity Pressure Reactor via Wet Air Oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Park, Gwon Woo [Biomass and Waste Energy Laboratory, KIER, Daejeon (Korea, Republic of); Seo, Tae Wan; Lee, Hong-Cheol; Hwang, In-Ju [Environmental and Plant Engineering Research Institute, KICT, Goyang (Korea, Republic of)

    2016-04-15

    Efficacious wastewater treatment is essential for increasing sewage sludge volume and implementing strict environmental regulations. The operation cost of sludge treatment amounts up to 50% of the total costs for wastewater treatment plants, therefore, an economical sludge destruction method is crucially needed. Amid several destruction methods, wet air oxidation (WAO) can efficiently treat wastewater containing organic pollutants. It can be used not only for sludge destruction but also for useful by-product production. Volatile fatty acids (VFAs), one of many byproducts, is considered to be an important precursor of biofuel and chemical materials. Its high reaction condition has instituted the study of gravity pressure reactor (GPR) for an economical process of WAO to reduce operation cost. Simulation of subcritical condition was conducted using Aspen Plus with predictive Soave-Redlich-Kwong (PSRK) equation of state. Conjointly, simulation analysis for GPR depth, oxidizer type, sludge flow rate and oxidizer injection position was carried out. At GPR depth of 1000m and flow rate of 2 ton/h, the conversion and yield of VFAs were 92.02% and 0.17g/g, respectively.

  16. Initial studies of oxidation processes on filter surfaces and their impack on perceived air quality

    DEFF Research Database (Denmark)

    Bekö, Gabriel; Halás, Oto; Clausen, Geo

    2003-01-01

    Ozone concentrations were monitored up- and downstream of used filter samples at airflows of 1.0 and 0.2 L s-1. The ozone concentration in the air upstream of the filters was ~75 ppb, while the concentration downstream of the filter was initially ~ 35% lower at 1 L s-1 and ~ 55% lower at 0.2 L s-...

  17. Catalytic aerobic oxidation of phenols to ortho-quinones with air-stable copper precatalysts.

    Science.gov (United States)

    Askari, M S; Rodríguez-Solano, L A; Proppe, A; McAllister, B; Lumb, J-P; Ottenwaelder, X

    2015-07-21

    A range of air-stable copper species was examined for catalytic activity in the catalytic aerobic transformation of phenols into ortho-quinones. Efficient catalysis was obtained with commercially available copper(II) acetate. The stability of all constituents before mixing makes for a practical process that advances previously reported copper(I)-based oxygenations.

  18. Integration of GIS technology with air compliance for the Oak Ridge National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Gurney, I.A. [Oak Ridge National Lab., TN (United States); Humphreys, M.P. [USDOE Oak Ridge Operations Office, TN (United States)

    1994-12-31

    ORNL uses a Geographical Information System (GIS) to achieve air quality compliance effectively and with minimum expense. Since implementation of MapInfo for Environmental Air Compliance activities, plant-wide adoption of the sytem is occurring. The common forum for data exchange allows compliance groups to pursue more of a management and planning rather than merely a regulatory role. Field surveys are implemented by personnel directly involved with the activities and this data is then transmitted via MapInfo. Examples are given of how the Environmental Compliance Section at ORNL uses it to achieve air quality compliance for Titles III and V, NEPA, and NESHAPs.

  19. Speciation and Fate of Trace Metals in Estuarine Sediments Under Reduced and Oxidized Conditions, Seaplane Lagoon, Alameda Naval Air Station

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, S A; Day, P A; Esser, B; Randall, S

    2002-10-18

    We have identified important chemical reactions that control the fate of metal-contaminated estuarine sediments if they are left undisturbed (in situ) or if they are dredged. We combined information on the molecular bonding of metals in solids from X-ray absorption spectroscopy (XAS) with thermodynamic and kinetic driving forces obtained from dissolved metal concentrations to deduce the dominant reactions under reduced and oxidized conditions. We evaluated the in situ geochemistry of metals (cadmium, chromium, iron, lead, manganese and zinc) as a function of sediment depth (to 100 cm) from a 60-year record of contamination at the Alameda Naval Air Station, California. Results from XAS and thermodynamic modeling of porewaters show that cadmium and most of the zinc form stable sulfide phases, and that lead and chromium are associated with stable carbonate, phosphate, phyllosilicate, or oxide minerals. Therefore, there is minimal risk associated with the release of these trace metals from the deeper sediments contaminated prior to the Clean Water Act (1975) as long as reducing conditions are maintained. Increased concentrations of dissolved metals with depth were indicative of the formation of metal HS- complexes. The sediments also contain zinc, chromium, and manganese associated with detrital iron-rich phyllosilicates and/or oxides. These phases are recalcitrant at near-neutral pH and do not undergo reductive dissolution within the 60-year depositional history of sediments at this site. The fate of these metals during dredging was evaluated by comparing in situ geochemistry with that of sediments oxidized by seawater in laboratory experiments. Cadmium and zinc pose the greatest hazard from dredging because their sulfides were highly reactive in seawater. However, their dissolved concentrations under oxic conditions were limited eventually by sorption to or co-precipitation with an iron (oxy)hydroxide. About 50% of the reacted CdS and 80% of the reacted ZnS were

  20. Determination of the Clean Air Delivery Rate (CADR) of Photocatalytic Oxidation (PCO) Purifiers for Indoor Air Pollutants Using a Closed-Loop Reactor. Part II: Experimental Results.

    Science.gov (United States)

    Héquet, Valérie; Batault, Frédéric; Raillard, Cécile; Thévenet, Frédéric; Le Coq, Laurence; Dumont, Éric

    2017-03-06

    The performances of a laboratory PhotoCatalytic Oxidation (PCO) device were determined using a recirculation closed-loop pilot reactor. The closed-loop system was modeled by associating equations related to two ideal reactors: a perfectly mixed reservoir with a volume of VR = 0.42 m³ and a plug flow system corresponding to the PCO device with a volume of VP = 5.6 × 10(-3) m³. The PCO device was composed of a pleated photocatalytic filter (1100 cm²) and two 18-W UVA fluorescent tubes. The Clean Air Delivery Rate (CADR) of the apparatus was measured under different operating conditions. The influence of three operating parameters was investigated: (i) light irradiance I from 0.10 to 2.0 mW·cm(-2); (ii) air velocity v from 0.2 to 1.9 m·s(-1); and (iii) initial toluene concentration C₀ (200, 600, 1000 and 4700 ppbv). The results showed that the conditions needed to apply a first-order decay model to the experimental data (described in Part I) were fulfilled. The CADR values, ranging from 0.35 to 3.95 m³·h(-1), were mainly dependent on the light irradiance intensity. A square root influence of the light irradiance was observed. Although the CADR of the PCO device inserted in the closed-loop reactor did not theoretically depend on the flow rate (see Part I), the experimental results did not enable the confirmation of this prediction. The initial concentration was also a parameter influencing the CADR, as well as the toluene degradation rate. The maximum degradation rate rmax ranged from 342 to 4894 ppbv/h. Finally, this study evidenced that a recirculation closed-loop pilot could be used to develop a reliable standard test method to assess the effectiveness of PCO devices.