WorldWideScience

Sample records for air cleaning

  1. Airing 'clean air' in Clean India Mission.

    Science.gov (United States)

    Banerjee, T; Kumar, M; Mall, R K; Singh, R S

    2016-12-30

    The submission explores the possibility of a policy revision for considering clean air quality in recently launched nationwide campaign, Clean India Mission (CIM). Despite of several efforts for improving availability of clean household energy and sanitation facilities, situation remain still depressing as almost half of global population lacks access to clean energy and proper sanitation. Globally, at least 2.5 billion people do not have access to basic sanitation facilities. There are also evidences of 7 million premature deaths by air pollution in year 2012. The situation is even more disastrous for India especially in rural areas. Although, India has reasonably progressed in developing sanitary facilities and disseminating clean fuel to its urban households, the situation in rural areas is still miserable and needs to be reviewed. Several policy interventions and campaigns were made to improve the scenario but outcomes were remarkably poor. Indian census revealed a mere 31% sanitation coverage (in 2011) compared to 22% in 2001 while 60% of population (700 million) still use solid biofuels and traditional cook stoves for household cooking. Further, last decade (2001-2011) witnessed the progress decelerating down with rural households without sanitation facilities increased by 8.3 million while minimum progress has been made in conversion of conventional to modern fuels. To revamp the sanitation coverage, an overambitious nationwide campaign CIM was initiated in 2014 and present submission explores the possibility of including 'clean air' considerations within it. The article draws evidence from literatures on scenarios of rural sanitation, energy practises, pollution induced mortality and climatic impacts of air pollution. This subsequently hypothesised with possible modification in available technologies, dissemination modes, financing and implementation for integration of CIM with 'clean air' so that access to both sanitation and clean household energy may be

  2. Air Cleaning Technologies

    Science.gov (United States)

    2005-01-01

    Executive Summary Objective This health technology policy assessment will answer the following questions: When should in-room air cleaners be used? How effective are in-room air cleaners? Are in-room air cleaners that use combined HEPA and UVGI air cleaning technology more effective than those that use HEPA filtration alone? What is the Plasmacluster ion air purifier in the pandemic influenza preparation plan? The experience of severe acute respiratory syndrome (SARS) locally, nationally, and internationally underscored the importance of administrative, environmental, and personal protective infection control measures in health care facilities. In the aftermath of the SARS crisis, there was a need for a clearer understanding of Ontario’s capacity to manage suspected or confirmed cases of airborne infectious diseases. In so doing, the Walker Commission thought that more attention should be paid to the potential use of new technologies such as in-room air cleaning units. It recommended that the Medical Advisory Secretariat of the Ontario Ministry of Health and Long-Term Care evaluate the appropriate use and effectiveness of such new technologies. Accordingly, the Ontario Health Technology Advisory Committee asked the Medical Advisory Secretariat to review the literature on the effectiveness and utility of in-room air cleaners that use high-efficiency particle air (HEPA) filters and ultraviolet germicidal irradiation (UVGI) air cleaning technology. Additionally, the Ontario Health Technology Advisory Committee prioritized a request from the ministry’s Emergency Management Unit to investigate the possible role of the Plasmacluster ion air purifier manufactured by Sharp Electronics Corporation, in the pandemic influenza preparation plan. Clinical Need Airborne transmission of infectious diseases depends in part on the concentration of breathable infectious pathogens (germs) in room air. Infection control is achieved by a combination of administrative, engineering

  3. Clean Air and Water

    Centers for Disease Control (CDC) Podcasts

    2007-04-10

    The air we breathe and the water we drink are both vital components of our health. Nevertheless, bacteria, pollutants, and other contaminates can alter life-giving air and water into health-threatening hazards. Learn about how scientists at the Centers for Disease Control and Prevention work to protect the public from air and water-related health risks.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

  4. Air cleaning using regenerative silica gel wheel

    DEFF Research Database (Denmark)

    Fang, Lei

    2011-01-01

    This paper discussed the necessity of indoor air cleaning and the state of the art information on gas-phase air cleaning technology. The performance and problems of oxidation and sorption air cleaning technology were summarized and analysed based on the literature studies. Eventually, based on an...

  5. Clean Air Act. Revision 5

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-15

    This Reference Book contains a current copy of the Clean Air Act, as amended, and those regulations that implement the statute and appear to be most relevant to DOE activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. This Reference Book has been completely revised and is current through February 15, 1994.

  6. The Value of Clean Air

    Science.gov (United States)

    Shindell, D. T.

    2014-12-01

    How can society place a value on clean air? I present a multi-impact economic valuation framework called the Social Cost of Atmospheric Release (SCAR) that extends the Social Cost of Carbon (SCC) used previously for carbon dioxide (CO2) to a broader range of pollutants and impacts. Values consistently incorporate health impacts of air quality along with climate damages. The latter include damages associated with aerosol-induced hydrologic cycle changes that lead to net climate benefits when reducing cooling aerosols. Evaluating a 1% reduction in current global emissions, benefits with a high discount rate are greatest for reductions of co-emitted products of incomplete combustion (PIC), followed by sulfur dioxide (SO2), nitrogen oxides (NOx) and then CO2, ammonia and methane. With a low discount rate, benefits are greatest for CO2 reductions, though the sum of SO2, PIC and methane is substantially larger. These results suggest that efforts to mitigate atmosphere-related environmental damages should target a broad set of emissions including CO2, methane and aerosol/ozone precursors. Illustrative calculations indicate environmental damages are 410-1100 billion yr-1 for current US electricity generation ( 19-46¢ per kWh for coal, 4-24¢ for gas) and 3.80 (-1.80/+2.10) per gallon of gasoline ($4.80 (-3.10/+3.50) per gallon for diesel). These results suggest that total atmosphere-related environmental damages plus generation costs are much greater for coal-fired power than other types of electricity generation, and that damages associated with gasoline vehicles substantially exceed those for electric vehicles.

  7. Clean Air Markets - Compliance Query Wizard

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Compliance Query Wizard is part of a suite of Clean Air Markets-related tools that are accessible at http://ampd.epa.gov/ampd/. The Compliance module provides...

  8. Clean Air Markets - Quick Facts and Trends

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Quick Facts and Trends module is part of a suite of Clean Air Markets-related tools that are accessible at http://camddataandmaps.epa.gov/gdm/index.cfm. The...

  9. Clean Air Markets - Allowances Query Wizard

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Allowances Query Wizard is part of a suite of Clean Air Markets-related tools that are accessible at http://camddataandmaps.epa.gov/gdm/index.cfm. The Allowances...

  10. Clean air Hamilton 2001 progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-05-01

    This community initiative called Clean Air Hamilton was established to improve air quality in Hamilton, Ontario. It has been mandated to annually report on progress and provide advice with regard to current air quality issues. The quality of life of residents is improved as a result of the work performed by Clean Air Hamilton, and it also enhances Hamilton's image. Numerous inquiries have been received from City officials in several municipalities such as Toronto, Kitchener-Waterloo and Windsor as a testament to the success of the initiative. Financial support is received from all levels of government. The funding received from the Council has helped in attracting additional donations in support of this initiative. Clean Air Hamilton was involved in one capacity or another in research, emissions reduction projects and public awareness campaigns during 2001, and its contributions were valued at approximately 500,000 dollars. The City of Hamilton was awarded the United Nations for Human Settlements award as a result of Clean Air Hamilton's community process in local air quality improvement. In addition, the City received the Dubai International Award for Best Practices in Improving the Living Environment. Clean Air Hamilton is ready to move to the next phase, which requires moving current structures that supplements voluntary commitments with committed funding from key stakeholders. Since June 1996, the advisory level of 32 on the Air Pollution Index has not been reached, and rarely goes over 20. Throughout the 1990s, levels of toxics have decreased significantly. A three-year self-sustaining program should be developed and funding sought for those initiatives, discussions should be facilitated among industrial stakeholders when they address air quality issues, and research should continue to be supported and advice on current air quality issues be provided to City Council. 1 fig.

  11. 76 FR 40728 - Clean Air Act Advisory Committee (CAAAC); Request for Nominations for 2011 Clean Air Excellence...

    Science.gov (United States)

    2011-07-11

    ... AGENCY Clean Air Act Advisory Committee (CAAAC); Request for Nominations for 2011 Clean Air Excellence Awards Program AGENCY: Environmental Protection Agency (EPA). ACTION: Request for nominations for Clean Air Excellence Awards. ] SUMMARY: EPA established the Clean Air Excellence Awards Program in...

  12. 75 FR 35025 - Clean Air Act Advisory Committee (CAAAC); Request for Nominations for 2010 Clean Air Excellence...

    Science.gov (United States)

    2010-06-21

    ... AGENCY Clean Air Act Advisory Committee (CAAAC); Request for Nominations for 2010 Clean Air Excellence Awards Program AGENCY: Environmental Protection Agency (EPA). ACTION: Request for nominations for Clean Air Excellence Awards. SUMMARY: EPA established the Clean Air Excellence Awards Program in...

  13. Experimental study on energy performance of clean air heat pump

    DEFF Research Database (Denmark)

    Fang, Lei; Nie, Jinzhe; Olesen, Bjarne W.

    2014-01-01

    An innovative clean air heat pump (CAHP) was designed and developed based on the air purification capacity of regenerative silica gel rotor. The clean air heat pump integrated air purification, dehumidification and cooling in one unit. A prototype of the clean air heat pump was developed...

  14. 14 CFR 1260.34 - Clean air and water.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Clean air and water. 1260.34 Section 1260... AGREEMENTS General Provisions § 1260.34 Clean air and water. Clean Air and Water October 2000 (Applicable... the Clean Air Act (42 U.S.C. 1857c-8(c)(1) or the Federal Water Pollution Control Act (33 U.S.C....

  15. Should You Have the Air Ducts in Your Home Cleaned?

    Science.gov (United States)

    ... air ducts in your home cleaned. The U.S. Environmental Protection Agency (EPA) urges you to read this document in it entirety as it provides important information on the subject. Duct cleaning has never ...

  16. 77 FR 44672 - Notice of Lodging of Consent Decree Under the Clean Water and Clean Air Acts

    Science.gov (United States)

    2012-07-30

    ... of Lodging of Consent Decree Under the Clean Water and Clean Air Acts Notice is hereby given that on... resolve its violations of the Clean Air Act and the Clean Water Act. The Allegheny County Health... the Clean Water Act, Plaintiffs allege that Shenango violated the effluent limitations in the...

  17. 17th DOE nuclear air cleaning conference: proceedings. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    First, M.W. (ed.)

    1983-02-01

    Volume 2 contains papers presented at the following sessions: adsorption; noble gas treatment; personnel education and training; filtration and filter testing; measurement and instrumentation; air cleaning equipment response to accident related stress; containment venting air cleaning; and an open end session. Twenty-eight papers were indexed separately for inclusion in the Energy Data Base. Ten papers had been entered earlier.

  18. Air cleaning issues with contaminated sites

    Energy Technology Data Exchange (ETDEWEB)

    Bellamy, R.R. [Nuclear Regulatory Commission, King of Prussia, PA (United States)

    1997-08-01

    The US Nuclear Regulatory Commission has developed a list of contaminated sites that warrant special USNRC attention because they pose unique or complex decommissioning issues. This list of radiologically contaminated sites is termed the Site Decommissioning Management Plan (SDMP), and was first issued in 1990. A site is placed on the SDMP list if it has; (1) Problems with the viability of the responsible organization (e.g., the licensee for the site is unable or unwilling to pay for the decommissioning); (2) Large amounts of soil contamination or unused settling ponds or burial grounds that may make the waste difficult to dispose of; (3) The long-term presence of contaminated, unused buildings; (4) A previously terminated license; or (5) Contaminated or potential contamination of the ground water from on-site wastes. In deciding whether to add a site to the SDMP list, the NRC also considers the projected length of time for decommissioning and the willingness of the responsible organization to complete the decommissioning in a timely manner. Since the list was established, 9 sites have been removed from the list, and the current SDMP list contains 47 sites in 11 states. The USNRC annually publishes NUREG-1444, {open_quotes}Site Decommissioning Management Plan{close_quotes}, which updates the status of each site. This paper will discuss the philosophical goals of the SDMP, then will concentrate on the regulatory requirements associated with air cleaning issues at the SDMP sites during characterization and remediation. Both effluent and worker protection issues will be discussed. For effluents, the source terms at sites will be characterized, and measurement techniques will be presented. Off-site dose impacts will be included. For worker protection issues, air sampling analyses will be presented in order to show how the workers are adequately protected and their doses measured to satisfy regulatory criteria during decontamination operations. 1 tab.

  19. 75 FR 11560 - Notice of Lodging of Consent Decree Under the Clean Water Act and Clean Air Act

    Science.gov (United States)

    2010-03-11

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF JUSTICE Notice of Lodging of Consent Decree Under the Clean Water Act and Clean Air Act Notice is hereby given that... violations of the Clean Water Act, 33 U.S.C. 1251 et seq., and the Clean Air Act, 42 U.S.C. 7401 et seq....

  20. Proceedings of the fifteenth DOE nuclear air cleaning conference

    Energy Technology Data Exchange (ETDEWEB)

    First, M.W. (ed.)

    1979-02-01

    Papers presented are grouped under the following topics: noble gas separation, damage control, aerosols, test methods, new air cleaning technology from Europe, open-end, and filtration. A separate abstract was prepared for each paper.

  1. EnviroAtlas - Clean Air Metrics for Conterminous United States

    Data.gov (United States)

    U.S. Environmental Protection Agency — This EnviroAtlas web service supports research and online mapping activities related to EnviroAtlas (https://www.epa.gov/enviroatlas). The Clean Air category in this...

  2. New Air Cleaning Strategies for Reduced Commercial Building Ventilation Energy

    Energy Technology Data Exchange (ETDEWEB)

    Sidheswaran, Meera; Destaillats, Hugo; Sullivan, Douglas P.; Fisk, William J.

    2010-10-27

    Approximately ten percent of the energy consumed in U.S. commercial buildings is used by HVAC systems to condition outdoor ventilation air. Reducing ventilation rates would be a simple and broadly-applicable energy retrofit option, if practical counter measures were available that maintained acceptable concentrations of indoor-generated air pollutants. The two general categories of countermeasures are: 1) indoor pollutant source control, and 2) air cleaning. Although pollutant source control should be used to the degree possible, source control is complicated by the large number and changing nature of indoor pollutant sources. Particle air cleaning is already routinely applied in commercial buildings. Previous calculations indicate that particle filtration consumes only 10percent to 25percent of the energy that would otherwise be required to achieve an equivalent amount of particle removal with ventilation. If cost-effective air cleaning technologies for volatile organic compounds (VOCs) were also available, outdoor air ventilation rates could be reduced substantially and broadly in the commercial building stock to save energy. The research carried out in this project focuses on developing novel VOC air cleaning technologies needed to enable energy-saving reductions in ventilation rates. The minimum required VOC removal efficiency to counteract a 50percent reduction in ventilation rate for air cleaning systems installed in the HVAC supply airstream is modest (generally 20percent or less).

  3. Prototype air cleaning system for a firing range

    Energy Technology Data Exchange (ETDEWEB)

    Glissmeyer, J.A.; Mishima, J.; Bamberger, J.A.

    1985-01-01

    This report recommends air cleaning system components for the US Army Ballistics Research Laboratory's new large-caliber firing range, which is used for testing depleted uranium (DU) penetrators. The new air cleaning system has lower operating costs during the life of the system compared to that anticipated for the existing air cleaning system. The existing system consists of three banks of filters in series; the first two banks are prefilters and the last are high-efficiency particulate air (HEPA) filters. The principal disadvantage of the existing filters is that they are not cleanable and reusable. Pacific Northwest Laboratory focused the search for alternate air cleaning equipment on devices that do not employ liquids as part of the particle collection mechanism. Collected dry particles were assumed preferable to a liquid waste stream. The dry particle collection devices identified included electrostatic precipitators; inertial separators using turning vanes or cyclones; and several devices employing a filter medium such as baghouses, cartridge houses, cleanable filters, and noncleanable filters similar to those in the existing system. The economics of practical air cleaning systems employing the dry particle collection devices were evaluated in 294 different combinations. 7 references, 21 figures, 78 tables.

  4. Fundamentals of air cleaning technology and its application in cleanrooms

    CERN Document Server

    Xu, Zhonglin

    2014-01-01

    Fundamentals of Air Cleaning Technology and Its Application in Cleanrooms sets up the theoretical framework for cleanrooms. New ideas and methods are presented, which include the characteristic index of cleanrooms, uniform and non-uniform distribution characteristics, the minimum sampling volume, a new concept of outdoor air conditioning and the fundamentals of leakage-preventing layers. Written by an author who can look back on major scientific achievements and 50 years of experience in this field, this book offers a concise and accessible introduction to the fundamentals of air cleaning technology and its application. The work is intended for researchers, college teachers, graduates, designers, technicians and corporate R&D personnel in the field of HVAC and air cleaning technology. Zhonglin Xu is a senior research fellow at China Academy of Building Research.

  5. Ductless personalized ventilation with local air cleaning

    DEFF Research Database (Denmark)

    Dalewski, Mariusz; Vesely, Michal; Melikov, Arsen Krikor

    2012-01-01

    was equipped with an activated carbon filter installed at the air intake, while the DPV at the second desk was without such a filter. The air temperature in the occupied zone (1.1 m above the floor) was 29 °C. The pollution load in the room was simulated by PVC floor covering. The subjects assessed...

  6. Self-Cleaning Particulate Air Filter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA requires an innovative solution to the serious issue of particulate fouling on air revitalization component surfaces in order to address the potential for...

  7. The Clean Air Act and the Economy

    Science.gov (United States)

    Since 1970, cleaner air and a growing economy have gone hand in hand. The Act has created market opportunities that have helped to inspire innovation in cleaner technologies for which the United States has become a global market leader.

  8. Cleaning products and air fresheners: exposure to primary and secondary air pollutants

    DEFF Research Database (Denmark)

    Nazaroff, W.; Weschler, Charles J.

    2004-01-01

    . More than two dozen research articles present evidence of adverse health effects from inhalation exposure associated with cleaning or cleaning products. Exposure to primary and secondary pollutants depends on the complex interplay of many sets of factors and processes, including cleaning product...... by the US federal government as hazardous air pollutants (HAPs). California's Proposition 65 list of species recognized as carcinogens or reproductive toxicants also includes constituents of certain cleaning products and air fresheners. In addition, many cleaning agents and air fresheners contain chemicals...... that can react with other air contaminants to yield potentially harmful secondary products. For example, terpenes can react rapidly with ozone in indoor air generating many secondary pollutants, including TACs such as formaldehyde. Furthermore, ozone-terpene reactions produce the hydroxyl radical, which...

  9. New challenges to air/gas cleaning systems

    Energy Technology Data Exchange (ETDEWEB)

    Kovach, J.L. [NUCON International, Inc., Columbus, OH (United States)

    1997-08-01

    This paper discusses the need for changes in the design and manufacturing of air and gas cleaning systems to meet waste management and site remediation requirements. Current design and manufacturing practices are primarily directed toward evaluating operational problems with existing systems in nuclear reactor facilities. However, nuclear waste management needs have developed which are much broader in scope and have different processing conditions. Numerous examples of air cleaning needs for waste management activities are provided; the major differences from operating facility needs are the requirement for continuous effluent treatment under widely different processing conditions. Related regulatory issues are also discussed briefly. 1 ref.

  10. Plants Clean Air and Water for Indoor Environments

    Science.gov (United States)

    2007-01-01

    Wolverton Environmental Services Inc., founded by longtime government environmental scientist B.C. "Bill" Wolverton, is an environmental consulting firm that gives customers access to the results of his decades of cutting-edge bioremediation research. Findings about how to use plants to improve indoor air quality have been published in dozens of NASA technical papers and in the book, "How to Grow Fresh Air: 50 Houseplants That Purify Your Home or Office." The book has now been translated into 12 languages and has been on the shelves of bookstores for nearly 10 years. A companion book, "Growing Clean Water: Nature's Solution to Water Pollution," explains how plants can clean waste water. Other discoveries include that the more air that is allowed to circulate through the roots of the plants, the more effective they are at cleaning polluted air; and that plants play a psychological role in welfare in that people recover from illness faster in the presence of plants. Wolverton Environmental is also working in partnership with Syracuse University, to engineer systems consisting of modular wicking filters tied into duct work and water supplies, essentially tying plant-based filters into heating, ventilation, and air conditioning (HVAC) systems. Also, the company has recently begun to assess the ability of the EcoPlanter to remove formaldehyde from interior environments. Wolverton Environmental is also in talks with designers of the new Stennis Visitor's Center, who are interested in using its designs for indoor air-quality filters

  11. Evaluation of air cleaning technologies existing in the Danish market

    DEFF Research Database (Denmark)

    Ardkapan, Siamak Rahimi; Afshari, Alireza; Bergsøe, Niels Christian

    2014-01-01

    the ozone level significantly in the room. Moreover, they can cause generation of ultrafine particles and consequently increase ultrafine particle concentration in the room. The study suggests using a mechanical filter with low pressure drop as a recommended air cleaning technology in order to remove...

  12. Proceedings of the fifteenth DOE nuclear air cleaning conference

    Energy Technology Data Exchange (ETDEWEB)

    First, M.W. (ed.)

    1979-02-01

    Papers presented are grouped under the following topics: air cleaning; waste volume reduction and preparation for storage; tritium, carbon-14, ozone; containment of accidental releases; adsorbents and absorbents; and off-gas treatment. A separate abstract was prepared for each paper.

  13. The Clean Air Act Amendments of 1990: Hazardous Air Pollutant Requirements and the DOE Clean Coal Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Moskowitz, P.D.; DePhillips, M.; Fthenakis, V.M. [Brookhaven National Lab., Upton, NY (United States); Hemenway, A. [USDOE Assistant Secretary for Fossil Energy, Washington, DC (United States)

    1991-12-31

    The purpose of the US Department of Energy -- Office of Fossil Energy (DOE FE) Clean Coal Technology Program (CCTP) is to provide the US energy marketplace with advanced, efficient, and environmentally sound coal-based technologies. The design, construction, and operation of Clean Coal Technology Demonstration Projects (CCTDP) will generate data needed to make informed, confident decisions on the commercial readiness of these technologies. These data also will provide information needed to ensure a proactive response by DOE and its industrial partners to the establishment of new regulations or a reactive response to existing regulations promulgated by the US Environmental Protection Agency (EPA). The objectives of this paper are to: (1) Present a preliminary examination of the potential implications of the Clean Air Act Amendments (CAAA) -- Title 3 Hazardous Air Pollutant requirements to the commercialization of CCTDP; and (2) help define options available to DOE and its industrial partners to respond to this newly enacted Legislation.

  14. The Clean Air Act Amendments of 1990: Hazardous Air Pollutant Requirements and the DOE Clean Coal Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Moskowitz, P.D.; DePhillips, M.; Fthenakis, V.M. (Brookhaven National Lab., Upton, NY (United States)); Hemenway, A. (USDOE Assistant Secretary for Fossil Energy, Washington, DC (United States))

    1991-01-01

    The purpose of the US Department of Energy -- Office of Fossil Energy (DOE FE) Clean Coal Technology Program (CCTP) is to provide the US energy marketplace with advanced, efficient, and environmentally sound coal-based technologies. The design, construction, and operation of Clean Coal Technology Demonstration Projects (CCTDP) will generate data needed to make informed, confident decisions on the commercial readiness of these technologies. These data also will provide information needed to ensure a proactive response by DOE and its industrial partners to the establishment of new regulations or a reactive response to existing regulations promulgated by the US Environmental Protection Agency (EPA). The objectives of this paper are to: (1) Present a preliminary examination of the potential implications of the Clean Air Act Amendments (CAAA) -- Title 3 Hazardous Air Pollutant requirements to the commercialization of CCTDP; and (2) help define options available to DOE and its industrial partners to respond to this newly enacted Legislation.

  15. Evaluating The Operation Of Three Air Cleaners Working Individually In A Clean Room

    DEFF Research Database (Denmark)

    Ardkapan, Siamak Rahimi; Afshari, Alireza; Bergsøe, Niels Christian;

    2011-01-01

    , photochemical air purifier and corona discharge ionizer. The concentrations of ultrafine particles, ozone and total volatile organic compounds were measured both in a duct and in a clean room. It was found that the studied air cleaning technologies increased the ozone level in the clean room and the duct......The use of portable air cleaners is becoming increasingly popular in many countries including Denmark. Portable air cleaners are known for not only removing but also generating particles and gases. To clarify this, three air cleaning technologies were evaluated. They were nonthermal plasma...... that air cleaners should be evaluated in a clean room about generation of ozone to get more reliable evaluation....

  16. Market Initiatives for Clean Air Schools; Marktinitiatieven frisse scholen

    Energy Technology Data Exchange (ETDEWEB)

    Teeuwen, D. [Communication Concert, Weesp (Netherlands)

    2012-07-15

    Seven years ago, the Clean Air Schools Program was launched to encourage people to use less energy and improve the indoor environment. In 2012, the program Energy and Built Environment will no longer pay specific attention focused on school buildings. Therefore, the market needs to jump in. 'Market initiatives' refers to projects, products and services that contribute to the realization of Clean Air Schools and which are not initiated by the Dutch government [Dutch] Zeven jaar geleden is het Frisse Scholen Programma gestart om gemeenten en scholen te stimuleren om minder energie te gebruiken en het binnenmilieu te verbeteren. In 2012 biedt het programma Energie en Gebouwde Omgeving geen ruimte meer voor specifieke aandacht gericht op scholen. Daarom zal het stokje overgedragen moeten worden aan marktpartijen. Met 'marktinitiatieven' wordt gedoeld op projecten, producten en diensten die bijdragen aan de realisatie van Frisse Scholen en niet door de Rijksoverheid worden geinitieerd.

  17. 78 FR 77448 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2013-12-23

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... public meetings of the Clean Air Act Advisory Committee (CAAAC). The EPA established the CAAAC on... implementation of the Clean Air Act of 1990. The Committee advises on economic, environmental,...

  18. 40 CFR 2.301 - Special rules governing certain information obtained under the Clean Air Act.

    Science.gov (United States)

    2010-07-01

    ... information obtained under the Clean Air Act. 2.301 Section 2.301 Protection of Environment ENVIRONMENTAL... governing certain information obtained under the Clean Air Act. (a) Definitions. For the purpose of this section: (1) Act means the Clean Air Act, as amended, 42 U.S.C. 7401 et seq. (2)(i) Emission data...

  19. 76 FR 17671 - Notice of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2011-03-30

    ... of Proposed Consent Decree Under the Clean Air Act Notice is hereby given that on March 21, 2011, a... this Clean Air Act enforcement action resolves allegations by the Environmental Protection Agency, asserted in a complaint filed together with the Consent Decree, under Section 113(b) of the Clean Air...

  20. 76 FR 66718 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2011-10-27

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... Clean Air Act Advisory Committee (CAAAC) on November 19, 1990, to provide independent advice and counsel to EPA on policy issues associated with implementation of the Clean Air Act of 1990. The...

  1. 75 FR 25855 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2010-05-10

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... Clean Air Act Advisory Committee (CAAAC) on November 19, 1990, to provide independent advice and counsel to EPA on policy issues associated with implementation of the Clean Air Act of 1990. The...

  2. 76 FR 9609 - Notice of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2011-02-18

    ... of Proposed Consent Decree Under the Clean Air Act Notice is hereby given that on February 14, 2011... Consent Decree in this Clean Air Act enforcement action resolves allegations by the Environmental... in a complaint filed together with the Consent Decree, under Section 113(b) of the Clean Air Act,...

  3. 77 FR 66462 - Clean Air Act Advisory Committee; Notice of Charter Renewal

    Science.gov (United States)

    2012-11-05

    ... AGENCY Clean Air Act Advisory Committee; Notice of Charter Renewal AGENCY: Environmental Protection...'s Clean Air Act Advisory committee (CAAAC) will be renewed for an additional two-year period, as a... recommendations to the EPA Administrator on policy issues associated with implementation of the Clean Air Act....

  4. 78 FR 9388 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2013-02-08

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... the Clean Air Act Advisory Committee (CAAAC) on November 19, 1990, to provide independent advice and counsel to EPA on policy issues associated with implementation of the Clean Air Act of 1990. The...

  5. 75 FR 1379 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2010-01-11

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... Clean Air Act Advisory Committee (CAAAC) on November 19, 1990, to provide independent advice and counsel to EPA on policy issues associated with ] implementation of the Clean Air Act of 1990. The...

  6. 75 FR 79369 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2010-12-20

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... Clean Air Act Advisory Committee (CAAAC) on November 19, 1990, to provide independent advice and counsel to EPA on policy issues associated with implementation of the Clean Air Act of 1990. The...

  7. 76 FR 9610 - Notice of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2011-02-18

    ... of Proposed Consent Decree Under the Clean Air Act Notice is hereby given that on February 14, 2011... California. The Consent Decree in this Clean Air Act enforcement action resolves allegations by the...''), asserted in a complaint filed together with the Consent Decree, under Section 113(b) of the Clean Air...

  8. 78 FR 49511 - Clean Air Act Advisory Committee (CAAAC): Notice of Meeting

    Science.gov (United States)

    2013-08-14

    ... AGENCY Clean Air Act Advisory Committee (CAAAC): Notice of Meeting AGENCY: Environmental Protection... public meeting of the Clean Air Act Advisory Committee (CAAAC). The EPA established the CAAAC on November... implementation of the Clean Air Act of 1990. The Committee advises on economic, environmental,...

  9. Air Cleaning Devices for HVAC Supply Systems in Schools. Technical Bulletin.

    Science.gov (United States)

    Wheeler, Arthur E.

    Guidelines for maintaining indoor air quality in schools with HVAC air cleaning systems are provided in this document. Information is offered on the importance of air cleaning, sources of air contaminants and indoor pollutants, types of air cleaners and particulate filters used in central HVAC systems, vapor and gas removal, and performance…

  10. Ceramic membrane defouling (cleaning) by air Nano Bubbles.

    Science.gov (United States)

    Ghadimkhani, Aliasghar; Zhang, Wen; Marhaba, Taha

    2016-03-01

    Ceramic membranes are among the most promising technologies for membrane applications, owing to their excellent resistance to mechanical, chemical, and thermal stresses. However, membrane fouling is still an issue that hampers the applications at large scales. Air Nano Bubbles (NBs), due to high mass transfer efficiency, could potentially prevent fouling of ceramic membrane filtration processes. In this study, bench and pilot scale ceramic membrane filtration was performed with air NBs to resist fouling. To simulate fouling, humic acid, as an organic foulant, was applied to the membrane flat sheet surface. Complete membrane clogging was achieved in less than 6 h. Membrane defouling (cleaning) was performed by directly feeding of air NBs to the membrane cells. The surface of the ceramic membrane was superbly cleaned by air NBs, as revealed by atomic force microscope (AFM) images before and after the treatment. The permeate flux recovered to its initial level (e.g., 26.7 × 10(-9) m(3)/m(2)/s at applied pressure of 275.8 kPa), which indicated that NBs successfully unclogged the pores of the membrane. The integrated ceramic membrane and air NBs system holds potential as an innovative sustainable technology.

  11. Proceedings of the clean air and climate change summit

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    The Clean Air Partnership was established in the Greater Toronto Area (GTA) over 10 years ago to work on issues related to air pollution and climate change. This summit presented details of the partnership's municipal activities and provided an outline of various projects conducted to reduce air pollution, increase the use of green energy, and encourage residents to reduce their ecological footprint. Climate change was discussed in relation to the recent economic crisis and recently discovered problems related to ocean acidification. The International Energy Agency (IEA) annual report was discussed in relation to peak oil and future economic crises. Advancements in green energy policy in Ontario were outlined. Sustainable housing and renewable energy projects in Germany were presented along with successful urban designs in Melbourne, New York City, and Denver. The GTA-CAC inter-governmental declaration on clean air was discussed, and an interim progress report was presented. The summit concluded with a video presentation of a collaborative artistic piece about climate change and the Arctic. 11 figs.

  12. Pure Air`s advanced flue gas desulfurization clean coal project

    Energy Technology Data Exchange (ETDEWEB)

    Brown, J.R. [Pure Air Bailly Station, Chesterton, IN (United States)

    1998-12-31

    Pure Air`s Advanced Flue Gas Desulfurization (AFGD) Clean Coal Project successfully completed four and a half years of operation in December 1996 at Northern Indiana Public Service Company`s (NIPSCO) Bailly Generating Station. This project received a $60 million grant from the DOE Clean Coal II program. Included in this was a three year DOE demonstration period. The facility was designed, built and is owned and operated by Pure Air of Allentown, Pennsylvania, through its project company, Pure Air on the Lake, Limited Partnership. The project met or exceeded all performance criteria. It has averaged 95.3% SO{sub 2} removal, 99.9% availability and produced high quality commercial gypsum during this four and a half year period. It demonstrated many advanced technology features including a single, large absorber module serving two boilers, a wastewater evaporation system, an air rotary sparger for oxidation, and a new technology for agglomerating gypsum.

  13. Path instabilities of air bubbles rising in clean water

    CERN Document Server

    Wu, M; Wu, Mingming; Gharib, Moteza

    1998-01-01

    Experiments are conducted to study the path and shape of single air bubbles (diameter range 0.10- 0.20cm) rising freely in clean water. The experimental results demonstrate that the bubble shape has a bistable state, i. e. the bubble chooses to be in spherical or ellipsoidal shape depending on its generation mechanism. The path of a spherical/ellipsoidal bubble is found to change from a straight path to a zigzag/spiral path via a supercritical/subcritical bifurcation when the Reynolds number of the bubble exceeds a threshold.

  14. Investigation of air cleaning system response to accident conditions

    Energy Technology Data Exchange (ETDEWEB)

    Andrae, R.W.; Bolstad, J.W.; Foster, R.D.; Gregory, W.S.; Horak, H.L.; Idar, E.S.; Martin, R.A.; Ricketts, C.I.; Smith, P.R.; Tang, P.K.

    1980-01-01

    Air cleaning system response to the stress of accident conditions are being investigated. A program overview and hghlight recent results of our investigation are presented. The program includes both analytical and experimental investigations. Computer codes for predicting effects of tornados, explosions, fires, and material transport are described. The test facilities used to obtain supportive experimental data to define structural integrity and confinement effectiveness of ventilation system components are described. Examples of experimental results for code verification, blower response to tornado transients, and filter response to tornado and explosion transients are reported.

  15. 75 FR 34673 - Approval of the Clean Air Act, Section 112(l), Authority for Hazardous Air Pollutants: Air...

    Science.gov (United States)

    2010-06-18

    ...'') request for approval to implement and enforce Air Pollution Control Regulation Number 36, Control of Emissions from Organic Solvent Cleaning (``RI Regulation No. 36'') and Rhode Island Air Pollution Control.... Ira W. Leighton, Acting Regional Administrator, EPA New England. BILLING CODE 6560-50-P...

  16. Cleaning practices and cleaning products in nurseries and schools: to what extent can they impact indoor air quality?

    Science.gov (United States)

    Wei, W; Boumier, J; Wyart, G; Ramalho, O; Mandin, C

    2016-08-01

    In the framework of a nationwide survey on indoor air quality conducted from September 2009 to June 2011 in 310 nurseries, kindergartens, and elementary schools in all regions of France, cleaning practices and products were described through an extensive questionnaire completed on-site by expert building inspectors. The questionnaire included the cleaning frequencies and periods, cleaning techniques, whether windows were open during cleaning, and the commercial names of the products used. Analysis of the questionnaire responses showed that cleaning was generally performed daily for furniture and floors. It was performed mostly in the evening with wet mopping and with one or more windows open. Five hundred eighty-four different cleaning products were listed, among which 218 safety data sheets (SDSs) were available and analyzed. One hundred fifty-two chemical substances were identified in the SDSs. The typical substances in cleaning products included alcohols, chlorides, terpenes, aldehydes, and ethers; more than half of them are irritants. Two endocrine disruptors, 2-phenylphenol and Galaxolide, were identified in two cleaning products used every day to clean the floors, in seven kindergartens and in a nursery respectively. Eleven reactive substances containing C=C double bonds, mostly terpenes, were identified in a wide variety of cleaning products.

  17. Chicago Clean Air, Clean Water Project: Environmental Monitoring for a Healthy, Sustainable Urban Future

    Energy Technology Data Exchange (ETDEWEB)

    none, none; Tuchman, Nancy [Institute of Environmental Sustainability (IES), Chicago, IL (United States)

    2015-11-11

    The U.S. Department of Energy awarded Loyola University Chicago and the Institute of Environmental Sustainability (IES) $486,000.00 for the proposal entitled “Chicago clean air, clean water project: Environmental monitoring for a healthy, sustainable urban future.” The project supported the purchase of analytical instruments for the development of an environmental analytical laboratory. The analytical laboratory is designed to support the testing of field water and soil samples for nutrients, industrial pollutants, heavy metals, and agricultural toxins, with special emphasis on testing Chicago regional soils and water affected by coal-based industry. Since the award was made in 2010, the IES has been launched (fall 2013), and the IES acquired a new state-of-the-art research and education facility on Loyola University Chicago’s Lakeshore campus. Two labs were included in the research and education facility. The second floor lab is the Ecology Laboratory where lab experiments and analyses are conducted on soil, plant, and water samples. The third floor lab is the Environmental Toxicology Lab where lab experiments on environmental toxins are conducted, as well as analytical tests conducted on water, soil, and plants. On the south end of the Environmental Toxicology Lab is the analytical instrumentation collection purchased from the present DOE grant, which is overseen by a full time Analytical Chemist (hired January 2016), who maintains the instruments, conducts analyses on samples, and helps to train faculty and undergraduate and graduate student researchers.

  18. Proceedings of the 21st DOE/NRC Nuclear Air Cleaning Conference; Sessions 1--8

    Energy Technology Data Exchange (ETDEWEB)

    First, M.W. [ed.] [Harvard Univ., Boston, MA (United States). Harvard Air Cleaning Lab.

    1991-02-01

    Separate abstracts have been prepared for the papers presented at the meeting on nuclear facility air cleaning technology in the following specific areas of interest: air cleaning technologies for the management and disposal of radioactive wastes; Canadian waste management program; radiological health effects models for nuclear power plant accident consequence analysis; filter testing; US standard codes on nuclear air and gas treatment; European community nuclear codes and standards; chemical processing off-gas cleaning; incineration and vitrification; adsorbents; nuclear codes and standards; mathematical modeling techniques; filter technology; safety; containment system venting; and nuclear air cleaning programs around the world. (MB)

  19. Citizen Science Air Sensor Project with Clean Air Carolina and the Eastern Band of Cherokee Indians Fact Sheet

    Science.gov (United States)

    EPA scientists are partnering with Clean Air Carolina (CAC) in Charlotte, N.C., and the Eastern Band of Cherokee Indians (EBCI) in Cherokee, N.C., to conduct a citizen science air quality project in these regions.

  20. Clean Air for London (CLEARFLO) Final Campaign Summary

    Energy Technology Data Exchange (ETDEWEB)

    Worsnop, D. R. [Aerodyne Research, Inc., Billerica, MA (United States); Williams, L. R. [Aerodyne Research, Inc., Billerica, MA (United States); Herndon, S. C. [Aerodyne Research, Inc., Billerica, MA (United States); Dubey, M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ng, N. L. [Georgia Inst. of Technology, Atlanta, GA (United States); Thornton, J. [Univ. of Washington, Seattle, WA (United States); Knighton, B. [Montana State Univ., Bozeman, MT (United States); Coulter, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Prévôt, Ash [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    2016-03-01

    This field campaign funded the participation of scientists from seven different research groups and operated over thirty instruments during the Winter Intensive Operating Period (January-February 2012) of the Clean Air for London (ClearfLo) campaign. The campaign took place at a rural site in Detling, UK, 45 kilometers southeast of central London. The primary science questions for the ClearfLo winter IOP (intensive operational periods) were: 1) “what is the urban increment of particulate matter (PM) and other pollutants in the greater London area?” and 2) “what is the contribution of solid fuel use for home heating to wintertime PM?” An additional motivation for the Detling measurements was the question of whether coatings on black carbon particles enhance absorption.

  1. A review of potential alternatives for air cleaning at the Hanford Waste Vitrification Plant

    Energy Technology Data Exchange (ETDEWEB)

    Sehmel, G.A.

    1990-07-01

    Pacific Northwest Laboratory conducted this review in support of the Hanford Waste Vitrification Plant (HWVP) being designed by Fluor Daniel Inc. for the US Department of Energy (DOE). The literature on air cleaning systems is reviewed to identify potential air cleaning alternatives that might be included in the design of HWVP. An overview of advantages/disadvantages of the various air cleaning technologies follows. Information and references are presented for the following potential air cleaning alternatives: deep-bed glass-fiber filters (DBGF), high-efficiency particulate air filters (HEPA), remote modular filter systems, high-efficiency mist eliminators (HEME), electrostatic precipitators, and the sand filter. Selected information is summarized for systems in the United States, Belgium, Japan, and West Germany. This review addresses high-capacity air cleaning systems currently used in the nuclear industry and emphasizes recent developments. 10 refs., 9 figs., 3 tabs.

  2. 14 CFR 1274.926 - Clean Air-Water Pollution Control Acts.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Clean Air-Water Pollution Control Acts...-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative... 91-604) and section 308 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et...

  3. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  4. 75 FR 74046 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2010-11-30

    ... AGENCY Proposed Consent Decree, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency (EPA... section 113(g) of the Clean Air Act, as amended (``Act''), 42 U.S.C. 7413(g), notice is hereby given of a... Colorado doing business as Xcel Energy to operate the Pawnee coal-fired power plant in Morgan...

  5. 78 FR 42547 - Notice of Lodging of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2013-07-16

    ... of Lodging of Proposed Consent Decree Under the Clean Air Act On July 10, 2013, the Department of... provisions of the Clean Air Act, 42 U.S.C. 7401 et seq.; the Comprehensive Environmental Response... numerous activities at its wastewater treatment plant, its tanks, and its benzene extraction unit to...

  6. 75 FR 20863 - Notice of Lodging of Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2010-04-21

    ... of Lodging of Consent Decree Under the Clean Air Act Notice is hereby given that on April 16, 2010, a... complaint filed together with the Consent Decree that Defendants violated the Clean Air Act and regulations... bringing storage tanks and loading racks at their bulk gasoline terminals into compliance with the NSPS...

  7. 77 FR 5010 - Proposed Settlement Agreement, Clean Air Act Citizen Suit

    Science.gov (United States)

    2012-02-01

    ... AGENCY Proposed Settlement Agreement, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency... accordance with section 113(g) of the Clean Air Act, as amended (``CAA'' or the ``Act''), 42 U.S.C. 7413(g... shall jointly file a stipulation of dismissal with prejudice with the court, within 10 days of the...

  8. 77 FR 45605 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2012-08-01

    ... AGENCY Proposed Consent Decree, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency (EPA... section 113(g) of the Clean Air Act, as amended (``CAA'' or the ``Act''), 42 U.S.C. 7413(g), notice is... with prejudice. For a period of thirty (30) days following the date of publication of this notice,...

  9. 76 FR 75545 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2011-12-02

    ... AGENCY Proposed Consent Decree, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency (EPA... section 113(g) of the Clean Air Act, as amended (``CAA'' or the ``Act''), 42 U.S.C. 7413(g), notice is... request to the Court to dismiss this matter with prejudice. For a period of thirty (30) days following...

  10. 77 FR 14785 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2012-03-13

    ... AGENCY Proposed Consent Decree, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency (EPA... section 113(g) of the Clean Air Act, as amended (``CAA''), 42 U.S.C. 7413(g), notice is hereby given of a... would then dismiss the case with prejudice once EPA has fulfilled these obligations under the...

  11. 78 FR 30919 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2013-05-23

    ... AGENCY Proposed Consent Decree, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency (EPA... section 113(g) of the Clean Air Act, as amended (``CAA'' or the ``Act''), notice is hereby given of a... shall be terminated and the case dismissed with prejudice. For a period of thirty (30) days...

  12. 76 FR 17416 - Proposed Settlement Agreement, Clean Air Act Citizen Suit

    Science.gov (United States)

    2011-03-29

    ... AGENCY Proposed Settlement Agreement, Clean Air Act Citizen Suit AGENCY: Environmental Protection Agency... accordance with section 113(g) of the Clean Air Act, as amended (``CAA'' or the ``Act''), 42 U.S.C. 7413(g... dismiss this suit with prejudice. For a period of thirty (30) days following the date of publication...

  13. 76 FR 5609 - Notice of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2011-02-01

    ... of Proposed Consent Decree Under the Clean Air Act Notice is hereby given that on January 26, 2011, a... United States et al. v. HOVENSA L.L.C., Civil Action No. 1:11-cv-6. The Consent Decree in this Clean Air... Agency, asserted in a complaint filed together with the Consent Decree, under section 113(b) of the...

  14. 75 FR 61774 - Notice of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2010-10-06

    ... of Proposed Consent Decree Under the Clean Air Act Notice is hereby given that on September 28, 2010... Consent Decree in this Clean Air Act enforcement actions against Murphy Oil USA, Inc. (``Murphy... Louisiana asserted in a complaint filed together with the Consent Decree, under Section 113(b) of the...

  15. 40 CFR 23.3 - Timing of Administrator's action under Clean Air Act.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Timing of Administrator's action under Clean Air Act. 23.3 Section 23.3 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL JUDICIAL REVIEW UNDER EPA-ADMINISTERED STATUTES § 23.3 Timing of Administrator's action under Clean Air...

  16. CLEAN-AIR heat pump. Reduced energy consumption for ventilation in buildings by integrating air cleaning and heat pump. Final Report; CLEAN-AIR heat pump - Reduceret energiforbrug til ventilation af bygninger ved luftrensning integreret med luft varmepumpe. Slut rapport

    Energy Technology Data Exchange (ETDEWEB)

    Fang, L.; Olesen, Bjarne W.; Molinaro, G.; Simmonsen, P.; Skocajic, S. [Danmarks Tekniske Univ. Institut for Byggeri og Anlaeg, Lyngby (Denmark); Hummelshoej, R.M.; Carlassara, L. [COWI A/S, Lyngby, (Denmark); Groenbaek, H.; Hansen, Ole R. [Exhausto A/S, Langeskov (Denmark)

    2011-07-01

    This report summarizes task 1 of the Clean Air Heat Pump project - modelling and simulation on energy savings when using the clean air heat pump for ventilation, air cleaning and energy recovery. The total energy consumption of the proposed ventilation systems using clean air heat pump technology was calculated by a theoretical model and compared with the reference ventilation systems (conventional ventilation systems). The energy compared between the two systems includes energy used for heating, cooling and fan. The simulation and energy saving calculation was made for the application of the clean air heat pump in three typical climate conditions, i.e. mild-cold, mild-hot and hot and wet climates. Real climate data recorded from three cities in 2002 was used for the calculation. The three cities were Copenhagen (Denmark), Milan (Italy) and Colombo (Sir Lanka) which represent the above three typical climate zones. For the Danish climate (the mild cold climate), the calculations show that the ventilation system using clean air heat pump technology can save up to 42% of energy cost in winter compared to the conventional ventilation system. The energy saving in summer can be as high as 66% for the ventilation system with humidity control and 9% for the ventilation system without the requirement of humidity control. Since the Danish summer climate is very mild, over 80% of the yearly energy consumption for ventilation is used during winter season. It is, therefore, estimated that more than 35% annual energy saving for ventilation is expected in Denmark using the clean air heat pump ventilation technology. For the mild hot climate, e.g. the Italian climate, the calculations show that up to 63% of the energy saving can be achieved in summer season. For the winter mode, 17% reduction of the energy cost can be expected for the domestic use. For industrial use, the energy cost of the clean air heat pump may not be favourable due to the industrial price of gas in Italy is

  17. Implementation of the clean air strategy for Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Sandhu, H.S.; Angle, R.P. [Alberta Dept. of Environmental Protection, Alberta (Canada); Kelly, M. [Clean Air Strategic Alliance, Alberta (Canada)

    1995-12-31

    Air quality and its effects on the environment and human health have received considerable attention during the last three decades in Alberta, Canada. Among the issues receiving a high priority are acid deposition, smog and global warming. There are various sources of emissions to Alberta`s atmosphere, many of which relate to the extraction, processing, and burning of fossil fuels; pulp and paper manufacture; and transportation. There are also natural sources of contaminants, such as particulates from forest fires and methane from bogs. The extraction, processing and combustion of fossil fuels play an important role in Alberta`s economy. The province produces over 80 % of the oil and natural gas in Canada, and nearly half the coal. Low sulphur coal is used in power plants to supply more than 90 % of the electricity used in this province by nearly three million people. As a result, Alberta is responsible for about 27 % of the CO{sub 2}, 23 % of the nitrogen oxides, and 16 % of the SO{sub 2} emissions generated in Canada. Alberta`s air quality is monitored by the Government of Alberta at nine continuous, eight intermittent, over 250 static, and 12 precipitation monitoring stations. Parameters such as carbon monoxide, oxides of nitrogen, sulphur dioxide, particulates, and ion-content of precipitation are measured. Industry operates a large number of ambient and static SO{sub 2} and H{sub 2}S monitoring stations across Alberta, with monitoring costs estimated at 56-80 million USD annually. The unique features of the Clean Air Strategy for Alberta (CASA) have already been published elsewhere. This presentation discusses the mechanism and progress on its implementation. (author)

  18. Learning from 25 years of experience with the United States clean air act

    Energy Technology Data Exchange (ETDEWEB)

    Schulze, R.H. [Trinity Consultants Incorporated, Dallas, TX (United States)

    1995-12-31

    Twenty-five years ago, the United States embarked on a quest to attain clean air. President Nixon, in signing the Clean Air Act of 1970, defined clean air as the objective for the `70s. Although enormous progress has been made, much remains to be done. Newly constructed industry is quite clean, but many older facilities continue to operate with antiquated controls. Significant advances have been made in cleaning up the emissions from new automobiles, but two factors have impaired progress. First, cars last longer than they did in 1970, so the average age of the fleet has increased. Second, travel has increased as people have moved to the suburbs. Thus, the emission decreases from clean cars have not been as great as expected. This presentation will address some of the lessons learned from the efforts in the United States to implement clean air programs. In a large number of countries, excessively elaborate studies have been substituted for action programs. Since much is now known about air quality, fairly brief studies can define programs that should be undertaken. What may take longer is developing public support and enthusiasm for improved air quality. In most cases, it is desirable to reduce spending on studies and increase spending on devising and implementing plans, as well as effectively communicating the necessary changes to the public. Balanced spending on studies- and action programs is essential to a sound air quality control program. (author)

  19. Pure Air`s Advanced Flue Gas Desulfurization Clean Coal Project

    Energy Technology Data Exchange (ETDEWEB)

    Brown, J.R. [Pure Air Bailly Station, Chesterton, IN (United States)

    1997-12-31

    Pure Air`s Advanced Flue Gas Desulfurization (AFGD) Clean Coal Project successfully completed four and a half years of operation in December 1996 at Northern Indiana Public Service Company`s (NIPSCO) Bailly Generation Station. Included in this was a three year DOE demonstration period. The project was built by a joint venture company of Air Products and Chemicals, Inc. and Mitsubishi Heavy Industries America, Inc., utilizing Mitsubishi`s wet limestone flue gas desulfurization technology. The project met or exceeded all performance criteria. It has averaged 95.3% SO{sub 2} removal, 99.9% availability and produced 936,000 metric tons of high quality commercial gypsum during this four and a half year period. It demonstrated many advanced technology features including a single, large absorber module serving two boilers, a wastewater evaporation system, an air rotary sparger for oxidation, and a new technology for agglomerating gypsum. The AFGD system was designed, built, owned and operated by Pure Air and will continue to serve NIPSCO`s Bailly Station for at least another 15{1/2} years under an Own and Operate contract. The project enabled NIPSCO to cost effectively achieve full system wide compliance with the Phase 2 emission requirements for SO{sub 2} of the Clean Air Act Amendments (CAAA) of 1990 almost eight years before the target date. The project was the recipient of the Outstanding Engineering Achievement Award from the National Society of Professional Engineers in 1993 and the 1993 Powerplant Award from Power magazine. The data presented in this paper are based on performance during the first three years of operation.

  20. 3 CFR - State of California Request for Waiver Under 42 U.S.C. 7543(b), the Clean Air Act

    Science.gov (United States)

    2010-01-01

    ....C. 7543(b), the Clean Air Act Presidential Documents Other Presidential Documents Memorandum of January 26, 2009 State of California Request for Waiver Under 42 U.S.C. 7543(b), the Clean Air Act Memorandum for the Administrator of the Environmental Protection Agency Under the Clean Air Act (42...

  1. 40 CFR 22.34 - Supplemental rules governing the administrative assessment of civil penalties under the Clean Air...

    Science.gov (United States)

    2010-07-01

    ... administrative assessment of civil penalties under the Clean Air Act. 22.34 Section 22.34 Protection of... Clean Air Act. (a) Scope. This section shall apply, in conjunction with §§ 22.1 through 22.32, in...) of the Clean Air Act, as amended (42 U.S.C. 7413(d), 7524(c), 7545(d), and 7547(d))....

  2. New Air Cleaning Strategies for Reduced Commercial Building Ventilation Energy ? FY11 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Sidheswaran, Meera; Destaillats, Hugo; Cohn, Sebastian; Sullivan, Douglas P.; Fisk, William J.

    2011-10-31

    The research carried out in this project focuses on developing novel volatile organic compounds (VOCs) air cleaning technologies needed to enable energy-saving reductions in ventilation rates. we targeted a VOC air cleaning system that could enable a 50% reduction in ventilation rates. In a typical commercial HVAC system that provides a mixture of recirculated and outdoor air, a VOC air cleaner in the supply airstream must have a 15% to 20% VOC removal efficiency to counteract a 50% reduction in outdoor air supply.

  3. Keeping the Air Clean and Safe: An Anthrax Smoke Detector

    Science.gov (United States)

    2005-01-01

    Scientists at work in the Planetary Protection division at NASA s Jet Propulsion Laboratory (JPL) sterilize everything before blasting it to the Red Planet. They take great pains to ensure that all spacecraft are void of bacterial life, especially the microscopic bacteria that can live hundreds of years in their spore states. No one is quite sure what Earthly germs would do on Mars, but scientists agree that it is safest to keep the Martian terrain as undisturbed as possible. Errant Earth germs would also render useless the instruments placed on exploration rovers to look for signs of life, as the life that they registered would be life that came with them from Earth. A team at JPL, headed by Dr. Adrian Ponce, developed a bacterial spore-detection system that uses a simple and robust chemical reaction that visually alerts Planetary Protection crews. It is a simple air filter that traps micron-sized bacterial spores and then submits them to the chemical reaction. When the solution is then viewed under an ultraviolet light, the mixture will glow green if it is contaminated by bacteria. Scientists can then return to the scrubbing and cleaning stages of the sterilization process to remove these harmful bacteria. The detection system is the space-bound equivalent of having your hands checked for cleanliness before being allowed to the table; and although intended to keep terrestrial germs from space, this technology has awesome applications here on Mother Earth. The bacterial spore-detection unit can recognize anthrax and other harmful, spore-forming bacteria and alert people of the impending danger. As evidenced in the anthrax mailings of fall 2001 in the United States, the first sign of anthrax exposure was when people experienced flu-like symptoms, which unfortunately, can take as much as a week to develop after contamination. Anthrax cost 5 people their lives and infected 19 others; and the threat of bioterrorism became a routine concern, with new threats popping up

  4. Can commonly-used fan-driven air cleaning technologies improve indoor air quality? A literature review

    DEFF Research Database (Denmark)

    Zhang, Yinping; Mo, Jinhan; Li, Yuguo

    2011-01-01

    Air cleaning techniques have been applied worldwide with the goal of improving indoor air quality. The effectiveness of applying these techniques varies widely, and pollutant removal efficiency is usually determined in controlled laboratory environments which may not be realized in practice. Some...... air cleaners are largely ineffective, and some produce harmful by-products. To summarize what is known regarding the effectiveness of fan-driven air cleaning technologies, a state-of-the-art review of the scientific literature was undertaken by a multidisciplinary panel of experts from Europe, North...... technologies was able to effectively remove all indoor pollutants and many were found to generate undesirable by-products during operation. (2) Particle filtration and sorption of gaseous pollutants were among the most effective air cleaning technologies, but there is insufficient information regarding long...

  5. Effectiveness of HVAC duct cleaning procedures in improving indoor air quality.

    Science.gov (United States)

    Ahmad, I; Tansel, B; Mitrani, J D

    2001-12-01

    Indoor air quality has become one of the most serious environmental concerns as an average person spends about 22 hr indoors on a daily basis. The study reported in this article, was conducted to determine the effectiveness of three commercial HVAC (Heating Ventilation Air Conditioning) duct cleaning processes in reducing the level of airborne particulate matter and viable bioaerosols. The three HVAC sanitation processes were: (1) Contact method (use of conventional vacuum cleaning of interior duct surfaces); (2) Air sweep method (use of compressed air to dislodging dirt and debris); (3) Rotary brush method (insertion of a rotary brush into the ductwork to agitate and dislodge the debris). Effectiveness of these sanitation processes was evaluated in terms of airborne particulate and viable bioaerosol concentrations in residential homes. Eight identical homes were selected in the same neighborhood. Two homes were cleaned using each procedure and two were used as controls. It was found that both particle count readings and bioaerosol concentrations were higher when cleaning was being performed than before or after cleaning, which suggests that dirt, debris and other pollutants may become airborne as a result of disturbances caused by the cleaning processes. Particle count readings at 0.3 micron size were found to have increased due to cigarette smoking. Particle counts at 1.0 micron size were reduced due to HVAC duct cleaning. Post-level bioaerosol concentrations, taken two days after cleaning, were found to be lower than the pre-level concentrations suggesting that the cleaning procedures were effective to some extent. Homes cleaned with the Air Sweep procedure showed the highest degree of reduction in bioaerosol concentration among the three procedures investigated.

  6. Self-scrubbing coal{sup TM}: An integrated approach to clean air. A proposed Clean Coal Technology Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    This environmental assessment (EA) was prepared by the U.S.Department of Energy (DOE), with compliance with the National Environmental Policy Act (NEPA) of 1969, Council on Environmental Quality (CE) regulations for implementating NEPA (40 CFR 1500-1508) and DOE regulations for compliance with NEPA (10 CFR 1021), to evaluate the potential environmental impacts associated with a proposed demonstration project to be cost-shared by DOE and Custom Coals International (CCI) under the Clean Coal Technology (CCT) Demonstration Program of DOE`s Office of Fossil Energy. CCI is a Pennsylvania general partnership located in Pittsburgh, PA engaged in the commercialization of advanced coal cleaning technologies. The proposed federal action is for DOE to provide, through a cooperative agreement with CCI, cost-shared funding support for the land acquisition, design, construction and demonstration of an advanced coal cleaning technology project, {open_quotes}Self-Scrubbing Coal: An Integrated Approach to Clean Air.{close_quotes} The proposed demonstration project would take place on the site of the presently inactive Laurel Coal Preparation Plant in Shade Township, Somerset County, PA. A newly constructed, advanced design, coal preparation plant would replace the existing facility. The cleaned coal produced from this new facility would be fired in full-scale test burns at coal-fired electric utilities in Indiana, Ohio and PA as part of this project.

  7. Radical observations during the Clean air for London project

    Science.gov (United States)

    Whalley, L. K.; Stone, D.; Clancy, N.; Lee, J. D.; Laufs, S.; Kleffmann, J.; Heard, D. E.

    2012-12-01

    With greater than 50 % of the global population residing in urban conurbations, poor urban air quality has a demonstrable effect on human health. OH and HO2 radicals, (collectively termed HOx) together with RO2 radicals, mediate virtually all of the oxidative chemistry in the atmosphere, being responsible for the transformation of primary emissions into secondary pollutants such as NO2, O3 and particulates. Understanding the chemistry of free-radicals in the atmosphere is essential in improving predictions of the lifetimes of pollutants and spatial scales of their transport within urban areas. Results from earlier field campaigns in urban and polluted regions have demonstrated the significance of HONO photolysis and alkene ozonolysis in the production of HOx radicals. In many cases, however, measurements of HONO have not been made, reducing the ability to evaluate model successes for OH in these environments. Here we present measurements of OH, HO2, RO2 and OH reactivity taken during the wintertime (January - February, 2012) and summertime (July - August, 2012) as part of the Clean air for London (ClearfLo) project in London. RO2 was detected using a newly developed flow-reactor laser-induced fluorescence technique which is able to discriminate between HO2 and organic peroxy radicals [1]. Low concentrations of radicals were observed during the wintertime, midday [OH], [HO2] and [RO2] were ~ 0.04, 0.8 and 1.5 pptv respectively, comparable to observations of radicals at other urban locations in winter [2,3,4], and which displayed a negative correlation with NO concentrations. OH reactivity was high and largely tracked the diurnal profiles of NOx and CO, with the highest reactivity ~100 s-1 observed during the morning rush hour. Analysis of factors controlling OH concentrations during the wintertime suggests that the formation of OH from the photolysis of O3 and subsequent reaction of O(1D) with H2O is a minor contribution both under high and low NOx conditions owing

  8. 40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

    Science.gov (United States)

    2010-07-01

    ... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard...

  9. 40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

    Science.gov (United States)

    2010-07-01

    ... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a)...

  10. Self-Scrubbing Coal -- an integrated approach to clean air

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, K.E. [Custom Coals Corp., Pittsburgh, PA (United States)

    1997-12-31

    Carefree Coal is coal cleaned in a proprietary dense-media cyclone circuit, using ultrafine magnetite slurries, to remove noncombustible material, including up to 90% of the pyritic sulfur. Deep cleaning alone, however, cannot produce a compliance fuel from coals with high organic sulfur contents. In these cases, Self-Scrubbing Coal will be produced. Self-Scrubbing Coal is produced in the same manner as Carefree Coal except that the finest fraction of product from the cleaning circuit is mixed with limestone-based additives and briquetted. The reduced ash content of the deeply-cleaned coal will permit the addition of relatively large amounts of sorbent without exceeding boiler ash specifications or overloading electrostatic precipitators. This additive reacts with sulfur dioxide (SO{sub 2}) during combustion of the coal to remove most of the remaining sulfur. Overall, sulfur reductions in the range of 80--90% are achieved. After nearly 5 years of research and development of a proprietary coal cleaning technology coupled with pilot-scale validation studies of this technology and pilot-scale combustion testing of Self-Scrubbing Coal, Custom Coals Corporation organized a team of experts to prepare a proposal in response to DOE`s Round IV Program Opportunity Notice for its Clean Coal Technology Program under Public Law 101-121 and Public Law 101-512. The main objective of the demonstration project is the production of a coal fuel that will result in up to 90% reduction in sulfur emissions from coal-fired boilers at a cost competitive advantage over other technologies designed to accomplish the same sulfur emissions and over naturally occurring low sulfur coals.

  11. No Need to Wait for the Clean Air Dividend

    Science.gov (United States)

    Shindell, Drew

    2012-01-01

    upfront costs of some measures can be prohibitive even when they eventually pay for themselves. But this can be overcome by mechanisms such as international financing of capital costs. For other measures, the costs are typically borne by a few while the benefits accrue to everybody. In such cases civil society and governments must get involved. Governments are starting to act. In February, the US, Canada, Sweden, Bangladesh, Ghana and Mexico launched the Climate and Clean Air Coalition to support implementation of measures like these. This coalition will hopefully expand and achieve rapid, widespread adoption of measures to cut black carbon and ozone. While the climate benefits will be substantial, it is important to note that these measures cannot substitute for cuts in carbon dioxide. Black carbon, ozone, carbon monoxide and methane stay in the atmosphere for a fairly short time - a few days for black carbon and about a decade for methane. They thus respond quickly to emissions changes and give us substantial leverage over near-term climate change. In contrast, carbon dioxide is very long-lived and so responds slowly to emissions changes. This means that cuts have little immediate impact, but it also means they must be made now to avoid disastrous changes later on. Controlling short-lived climate pollutants is thus an issue of fairness. Much as failure to reduce carbon dioxide emissions soon would condemn future generations to disastrous change, failure to reduce near-term climate change condemns those alive today to suffer worsening effects of the sort already seen. Some wonder if we really can do both. We can, and we must.

  12. Air toxics provisions of the Clean Air Act: Potential impacts on energy

    Energy Technology Data Exchange (ETDEWEB)

    Hootman, H.A.; Vernet, J.E.

    1991-11-01

    This report provides an overview of the provisions of the Clean Air Act and its Amendments of 1990 that identify hazardous air pollutant (HAP) emissions and addresses their regulation by the US Environmental Protection Agency (EPA). It defines the major energy sector sources of these HAPs that would be affected by the regulations. Attention is focused on regulations that would cover coke oven emissions; chromium emission from industrial cooling towers and the electroplating process; HAP emissions from tank vessels, asbestos-related activities, organic solvent use, and ethylene oxide sterilization; and emissions of air toxics from municipal waste combustors. The possible implications of Title III regulations for the coal, natural gas, petroleum, uranium, and electric utility industries are examined. The report discusses five major databases of HAP emissions: (1) TRI (EPA's Toxic Release Inventory); (2) PISCES (Power Plant Integrated Systems: Chemical Emissions Studies developed by the Electric Power Research Institute); (3) 1985 Emissions Inventory on volatile organic compounds (used for the National Acid Precipitation Assessment Program); (4) Particulate Matter Species Manual (EPA); and (5) Toxics Emission Inventory (National Aeronautics and Space Administration). It also offers information on emission control technologies for municipal waste combustors.

  13. Air toxics provisions of the Clean Air Act: Potential impacts on energy

    Energy Technology Data Exchange (ETDEWEB)

    Hootman, H.A.; Vernet, J.E.

    1991-11-01

    This report provides an overview of the provisions of the Clean Air Act and its Amendments of 1990 that identify hazardous air pollutant (HAP) emissions and addresses their regulation by the US Environmental Protection Agency (EPA). It defines the major energy sector sources of these HAPs that would be affected by the regulations. Attention is focused on regulations that would cover coke oven emissions; chromium emission from industrial cooling towers and the electroplating process; HAP emissions from tank vessels, asbestos-related activities, organic solvent use, and ethylene oxide sterilization; and emissions of air toxics from municipal waste combustors. The possible implications of Title III regulations for the coal, natural gas, petroleum, uranium, and electric utility industries are examined. The report discusses five major databases of HAP emissions: (1) TRI (EPA`s Toxic Release Inventory); (2) PISCES (Power Plant Integrated Systems: Chemical Emissions Studies developed by the Electric Power Research Institute); (3) 1985 Emissions Inventory on volatile organic compounds (used for the National Acid Precipitation Assessment Program); (4) Particulate Matter Species Manual (EPA); and (5) Toxics Emission Inventory (National Aeronautics and Space Administration). It also offers information on emission control technologies for municipal waste combustors.

  14. Your Right to Clean Air, A Manual for Citizen Action.

    Science.gov (United States)

    1970

    This manual provides the citizen with basic information for taking action against air pollution. A summary of the effects of various concentrations of sulfur oxides, particulate matter, carbon monoxide, photochemical smog, and hydrocarbons is presented. Suggestions are made for obtaining information about community air pollution problems, and how…

  15. Wet-air oxidation cleans up black wastewater

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    Sterling Organics produces the analgesic paracetamol (acetaminophen) at its Dudley, England, plant. The wastewater from the batch process contains intermediates such as para-aminophenol (PAP) and byproducts such as thiosulfates, sulfites and sulfides. To stay ahead of increasingly strict environmental legislation, Sterling Organics installed a wet-air oxidation system at the Dudley facility in August 1992. The system is made by Zimpro Environmental Inc. (Rothschild, Wis.). Zimpro's wet-air oxidation system finds a way around the limitations of purely chemical or physical processes. In the process, compressed air at elevated temperature and pressure oxidizes the process intermediates and byproducts and removes the color from the wastewater.

  16. Human Response to Ductless Personalised Ventilation: Impact of Air Movement, Temperature and Cleanness on Eye Symptoms

    DEFF Research Database (Denmark)

    Dalewski, Mariusz; Fillon, Maelys; Bivolarova, Maria;

    2013-01-01

    The performance of ductless personalized ventilation (DPV) in conjunction with displacement ventilation (DV) was studied in relation to peoples’ health, comfort and performance. This paper presents results on the impact of room air temperature, using of DPV and local air filtration on eye blink...... rate and tear film quality. In a test room with DV and six workstations 30 human subjects were exposed for four hours to each of the following 5 experimental conditions: 23 °C and DV only, 23 °C and DPV with air filter, 29 °C and DV only, 29 °C and DPV, and 29 °C and DPV with air filter. At warm...... environment facially applied individually controlled air movement of room air, with or without local filtering, did not have significant impact on eye blink frequency and tear film quality. The local air movement and air cleaning resulted in increased eye blinking frequency and improvement of tear film...

  17. CAN SORBENT-BASED GAS PHASE AIR CLEANING FOR VOCS SUBSTITUTE FOR VENTILATION IN COMMERCIAL BUILDINGS?

    Energy Technology Data Exchange (ETDEWEB)

    Fisk, William; Fisk, William J.

    2007-08-01

    This paper reviews current knowledge about the suitability of sorbent-based air cleaning for removing volatile organic compounds (VOCs) from the air in commercial buildings, as needed to enable reductions in ventilation rates and associated energy savings. The principles of sorbent air cleaning are introduced, criteria are suggested for sorbent systems that can counteract indoor VOC concentration increases from reduced ventilation, major findings from research on sorbent performance for this application are summarized, and related priority research needs are identified. Major conclusions include: sorbent systems can remove a broad range of VOCs with moderate to high efficiency, sorbent technologies perform effectively when challenged with VOCs at the low concentrations present indoors, and there is a large uncertainty about the lifetime and associated costs of sorbent air cleaning systems when used in commercial buildings for indoor VOC control. Suggested priority research includes: experiments to determine sorbent system VOC removal efficiencies and lifetimes considering the broad range and low concentration of VOCs indoors; evaluations of in-situ regeneration of sorbents; and an updated analysis of the cost of sorbent air cleaning relative to the cost of ventilation.

  18. Window-mounted unit cleans air at hazardous waste site

    Energy Technology Data Exchange (ETDEWEB)

    Battaglia, J.M. (Independent Equipment Corp., Raritan, NJ (United States)); Sawyer, P.

    1994-07-01

    Uncontrolled hazardous waste sites present the potential for exposure to numerous airborne chemicals--both identified and unidentified. This was the case at an Elizabeth, N.J., remediation project managed by a major environmental contractor. The four-acre site housed three active manufacturing facilities and was bordered by an operation commuter railroad line. About 6,300 drums of assorted organic chemicals, mostly acid chlorides and bromides, awaited sampling and removal. In addition, 120 tanks and vessels required sampling, characterization and removal. Due to site restrictions, support trailers were located relatively close to active work areas. Damaged drums littering the site contained water-reactive, organic acid chlorides and bromides, and released slight emissions during humid or rainy conditions. Shifting winds could (and did) carry trace releases or trace contaminants toward the trailers, potentially exposing unprotected workers. Efforts were begun to alleviate even trace contaminant at levels in the remediation site's temporary office trailers. One potential solution to managing trace contaminants at the site was to use a window-mounted, air conditioner-type unit that would replenish each trailer with filtered air three times an hour, and provide positive pressure in the trailer to compensate for repeated openings and closings of doors. The design uses common, off-the-shelf components to temper the approximately 10 percent makeup air, which provides positive pressure.

  19. Proceedings of the 10th world clean air congress. Impacts and management

    Energy Technology Data Exchange (ETDEWEB)

    Kaemaeri, J.; Tolvanen, M.; Anttila, P.; Salonen, R.O. [eds.

    1995-12-31

    Rapid economical growth and expansion of human population have produced a number of environmental problems with varying geographic dimensions. While local problems remain near the pollution sources, the focus of the scientific community is more and more shifted towards regional, continental and global consequences of air pollutants. The theme of the 10th Clean Air Congress `Growing Challenges from Local to Global` reflects the growing demand from the scientific and professional community working in air pollution prevention and environmental protection - more and more complex mechanisms should be understood on a growing spatial scale. The 10th World Clean Air Congress addresses in its more than 400 presentations, documented in three Volumes of Proceedings, the history, the present and the potential futures of the air pollution problems. This volume includes all papers of paths C `Pollutant Impacts`, D `Pollution Management`, and E `Health Effects`. Path C includes numerous highly relevant papers dealing with climate change and greenhouse gases, as well as with environmental effects of air pollutants mostly on materials and vegetation. The most critical issues on air pollutant management throw light on national and regional abatement strategies and on the applicability of various tools for pollution management. The path on effects on human health includes a session on `Air pollution epidemiology` sponsored by the Economic Commission for Europe and a session on `Health effect control strategies` sponsored by the UN World Health Organization. In these sessions invited speakers describe the current understanding of human responses to air pollution exposure

  20. 78 FR 1883 - Notice of Lodging of Proposed Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2013-01-09

    ... alleges that Wisconsin Public Service Corporation (``WPS'') failed to comply with certain requirements of... regulations. The complaint alleges that WPS failed to obtain appropriate permits and failed to install and... resolve past Clean Air Act violations and would require WPS to reduce harmful emissions of sulfur...

  1. 77 FR 41930 - Bleed Air Cleaning and Monitoring Equipment and Technology

    Science.gov (United States)

    2012-07-17

    ... an opportunity to participate in #0;the rule making prior to the adoption of the final rules. #0; #0... Equipment and Technology ACTION: Notice; request for information. SUMMARY: The FAA seeks information from industry developers, manufacturers, and the public related to effective air cleaning technology and...

  2. Key Technology and Experimental Results of the Clean Air Heated Facility for Supersonic Combustion

    Institute of Scientific and Technical Information of China (English)

    ZHONG Zipeng; SONG Wenyan; LE Jialing

    2009-01-01

    The scramjet, which is the propulsion of hypersonic vehicle, has become the focus in many military developed countries. The ground tests play an important role in the research of scramjet. There is defect of test medium contamination (the thermochemical characteristic of the ground test medium is different from that of the flight medium) in existing ground test facilities for scramjet combustor experiment. To solve the problem of test medium contamination, the first clean air heated facility of China for scramjet combustor experiment is designed. The key technology of designing the clean air heated facility is summarized. By using bypass duct, combustor model is protected from high temperature. To reduce the switching time between main duct and bypass duct, solenoid valve and water-cooled system were used. Having centrosymmetric structure, the heat radiating area of the facility and heat loss of the facility are much lower than others. Clean air heated facility is adopted to conduct experiment, which is the first experiment of China in clean air inflow, research on hydrogen-fueled and ethylene-fueled ignition and combustion for scramjet combustor at different equivalence ratio. Successful ignition and sustained combustion of hydrogen has been achieved. Successful ethylene ignition and sustained main stream combustion is achieved with normal fuel injection and taking hydrogen as pilot flame. Experiment result shows that the wall pressure of combustor model rises when the equivalence ratio of hydrogen rises. As the wall pressure of combustor model rises, the pressure disturbance influences the shock train in the upstream.

  3. Assessing the Link between Environmental Concerns and Consumers' Decisions to Use Clean-Air Vehicles

    Science.gov (United States)

    Plax, Timothy G.; Kearney, Patricia; Ross, Ted J.; Jolly, J. Christopher

    2008-01-01

    A consulting contract with the California Air Resources Board led to a project examining how California drivers' and fleet managers' perceptions, attitudes, and consumer behavior regarding Clean Vehicle Technologies influenced their own energy choices when it came to purchasing vehicles. The consultants examined archival research, conducted focus…

  4. 78 FR 11682 - Notice of Lodging of Proposed Settlement Under the Clean Air Act

    Science.gov (United States)

    2013-02-19

    ... violations of the Risk Management Program requirements of the Clean Air Act and 40 CFR part 68 at three of... reproduction costs. Please mail your request and payment to: Consent Decree Library, U.S. DOJ--ENRD, P.O....

  5. Human Response to Ductless Personalized Ventilation with Local Air Cleaning: Air Quality and Prevalence of SBS Symptoms

    DEFF Research Database (Denmark)

    Dalewski, Mariusz; Bivolarova, Maria; Fillon, Maelys;

    2013-01-01

    The impact of local air cleaning and cooling of the head region by ductless personalized ventilation (DPV) on perceived air quality (PAQ) and Sick Building Syndrome (SBS) symptoms was studied. Thirty subjects participated in experiments performed in a test room with displacement ventilation (DV...... and supplied it to the breathing zone of the subjects. The subjects were allowed to control the position of the DPV supply diffuser and the personalized flow rate. Each subject participated in five 4-hour experiments: 23 °C with DV only, 23 °C with DPV with air filter, 29 °C with DV only, 29 °C with DPV...

  6. Air emission points for facilities in Iowa with operating permits for Title V of the Federal Clean Air Act_considered MAJOR permits

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — Air emission points for facilities in Iowa with operating permits for Title V of the Federal Clean Air Act, considered "major" permits. Also includes emission points...

  7. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Science.gov (United States)

    2010-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT...) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act are... Contracts (Appalachian Contracts) § 633.211 Implementation of the Clean Air Act and the Federal...

  8. 78 FR 63494 - Notice of Lodging of Proposed Consent Decree Under the Clean Air Act and the Emergency Planning...

    Science.gov (United States)

    2013-10-24

    ... of Lodging of Proposed Consent Decree Under the Clean Air Act and the Emergency Planning and Community Right-To Know Act On September 30, 2013, the Department of Justice lodged a proposed Consent... Door Company, Civil Action No. 6:13-cv-01738-MC. In this lawsuit filed under the Clean Air Act and...

  9. 75 FR 68094 - Partial Grant and Partial Denial of Clean Air Act Waiver Application Submitted by Growth Energy...

    Science.gov (United States)

    2010-11-04

    ... Partial Denial of Clean Air Act Waiver Application Submitted by Growth Energy To Increase the Allowable... AGENCY [EPA-HQ-OAR-2009-0211; FRL-9215-5] Partial Grant and Partial Denial of Clean Air Act Waiver Application Submitted by Growth Energy To Increase the Allowable Ethanol Content of Gasoline to 15...

  10. Citizen suit Clean Air Act enforcement: An update

    Energy Technology Data Exchange (ETDEWEB)

    Wright, W.G. Jr.

    1999-07-01

    Almost every federal environmental statute has a provision that allows citizens to sue violators in lieu of governmental enforcement authorities under certain circumstances. Generally, if the relevant governmental enforcement authority was not deemed to be diligently prosecuting enforcement action against an alleged violator and certain procedural requirements were met a citizens suit could be filed in federal court. If a violation was proved penalties could be assessed against the violator and the plaintiff citizen could receive reimbursement of both his or her attorney's fees and other expenses. Historically, however, the only federal statute that has been the subject of significant citizens suit activity has been the federal Clean Water Act (CWA). This paper will explore a variety of events that are expected to significantly increase the number of citizen suits CAA permitted facilities will face over the next ten years. The paper will briefly address the role the Title V operating permit will play. It will also include a discussion of how this permit will now encompass specific emission limitations along with a mandate to report exceedances. Further, and equally important, will be the role of the 1997 federal Environmental Protection Agency any credible evidence rule which potentially broadens the type, amount, and accessibility available to a CAA citizen suit plaintiff. This rule along with the additional monitoring data that will be generated by the Title V periodic and compliance assurance monitoring requirements will be an issue. Two important CAA citizen suits will be discussed which illustrate the potential role of credible evidence. Also, recent citizen suit decisions involving other federal environmental statutes with implications for the CAA will be examined. Further, the paper will provide some thoughts on how facilities can protect themselves to the extent possible against citizen suits.

  11. Bed-integrated local exhaust ventilation system combined with local air cleaning for improved IAQ in hospital patient rooms

    DEFF Research Database (Denmark)

    Bivolarova, Mariya Petrova; Melikov, Arsen Krikor; Mizutani, Chiyomi;

    2016-01-01

    The performance of a ventilated mattress (VM) used as a bed-integrated local exhaust ventilation system combined with air cleaning fabric (acid-treated activated carbon fibre (ACF) fabric) was developed and studied. The separate and combined effect of the VM and the local air cleaning for reducing...... micro-environment was exhausted. Two modes of operation were studied: 1) the exhausted polluted air was discharged out of the room and 2) the polluted air was cleaned by the ACF material installed inside the mattress and recirculated back into the room. Both modes of operation efficiently reduced...

  12. Give clean air the economic value it deserves

    Energy Technology Data Exchange (ETDEWEB)

    Verhagen, H. [United Air Fund, Amsterdam (Netherlands)

    2000-07-01

    India contributes more to the management of the atmosphere than a country like the Netherlands. This is not to the credit of the Indian government; rather, it is merely a consequence of poverty. Poor people use almost no fossil fuels and emit almost no CO2. Paying developing countries for this environmental service to the world community would create a financial incentive to continue to provide this service in the future, while at the same time generating additional funds to improve the living standards of the poorest people. The attractiveness of this approach depends on one important assumption: the conventional development path - economic growth implies emissions - must be replaced by a sustainable development path delinks economic growth from increasing emissions. Rich industrialised countries also have an interest in such decoupling. The compensation they pay the developing countries would fall proportionately to the reduction of their CO2 emissions. So an incentive is created on both sides to switch over to a low-carbon energy strategy. After the completion of this transition, every country can use as much energy as it wants, because energy consumption would then no longer cause CO2 emissions. This is the picture of the future to which the United Air Fund aspires.

  13. Investigation of efficiency of air cleaning from acetone using a segmental construction biofilter

    Directory of Open Access Journals (Sweden)

    Denas Bacevičius

    2015-10-01

    Full Text Available Volatile organic compounds, e. g. acetone, have a direct impact on climate change, decrease of ozone in the air, and on the growth of greenhouse effect. One of the most popular air purifying methods from VOC is a biological air cleaning. Experimental investigations were conducted to determine the efficiency of the new structure of biofilter with polypropylene plates segments. During the investigations the efficiency of segmental construction biofilter of air purification at different initial concentrations of pollutants was determined. Different concentrations of pollutants were estimated during the acetone dilution with water. During the tests the efficiency of biofilter air purification from acetone vapor and its change under different concentrations of vapors was set. Based on test results, the maximum efficiency of biofilter air purification was up to 93%. Studies have shown that increasing the allowable pollutant concentration, the efficiency of air purification unit decreases. Increasing the concentration of supplied acetone vapor into the biofilter from 232 to 701 mg/m3, cleaning efficiency decreased from 92.8 to 82.3%. Since microorganisms fail to oxidize organic compounds, the filter works better at lower initial concentrations of pollutants.

  14. Rationing health protection: a proposal to exempt nuisance dust from US Clean Air Act regulations.

    Science.gov (United States)

    Centner, Terence J; Colson, Gregory

    2013-03-15

    The US House of Representative has passed a bill called the "Farm Dust Regulation Prevention Act" (Dust Act) that would exempt most types of particulate matter (PM) in rural areas from the air quality controls of the US Clean Air Act. The Dust Act would markedly change the country's air quality standards. An examination of the proposed provisions shows that they would exempt non-combustion PM pollutants from mining, smelting, petroleum production, and power generation from existing air quality standards. Persons downwind from pollutants generated in rural areas could be exposed to concentrations of carcinogenic heavy metals, asbestos, and benzene known to adversely affect their health and ecological resources. Existing federal air quality standards based on science would be replaced by a flexible standard that rations health protection.

  15. A Multilevel Test of Constrained Choices Theory: The Case of Tobacco Clean Air Restrictions.

    Science.gov (United States)

    Vuolo, Mike; Kadowaki, Joy; Kelly, Brian C

    2016-09-01

    According to Bird and Rieker's sociology of constrained choices, decisions and priorities concerning health are shaped by the contexts-including policy, community, and work/family-in which they are formulated. While each level received attention in the original and subsequent research, we contend their constrained choices theory provides a powerful multilevel framework for modeling health outcomes. We apply this framework to tobacco clean air restrictions, combining a comprehensive database of tobacco policies with the National Longitudinal Survey of Youth 1997 from ages 19 to 31. Using multilevel panel models, we find that clean air policies lower the odds of past 30 day smoking and dependence while controlling for other policy-, city-, and individual-level constraints. We also find unique between- and within-person effects, as well as gender effects, for the constraint levied by smoking bans. We argue for the theory's broad applicability beyond commonly cited findings regarding gender and biological influences.

  16. The Impact of the Clean Air Acts on Coal Mining Employment in Kentucky

    OpenAIRE

    Hoag, John H.; Reed, J. David

    2002-01-01

    This article provides empirical evidence that environmental legislation affecting coal mining employment passed in 1977 had different effects on Western Kentucky, where the coal is of higher sulfur content, compared to Eastern Kentucky, where coals are of lower sulfur content, while the 1990 amendments to the Clean Air Act had no statistically significant impact in either region. The 1977 law generated a statistically significant reduction in West Kentucky employment. In addition, it appears ...

  17. Experimental Study on Indoor Air Cleaning Technique of Nano-Titania Catalysis Under Plasma Discharge

    Institute of Scientific and Technical Information of China (English)

    GAO Deli; YANG Xuechang; ZHOU Fei; WU Yuhuang

    2008-01-01

    In this study, a new technique of air cleaning by plasma combined with catalyst was proposed, which consisted of electrostatic precipitation, volatile organic compounds (VOCs) decomposition and sterilization. A novel indoor air purifier based on this technique was adopted. The experimental results showed that formaldehyde decomposition by the plasma-catalyst hybrid system was more efficient than that by plasma only. Positive discharge was better than negative discharge in formaldehyde removal. Meanwhile, the outlet concentration of ozone byproduct was effectively reduced by the nano-titania catalyst.

  18. Experimental evaluation on energy performance of innovative clean air heat pump for indoor environment control in summer and winter seasons

    DEFF Research Database (Denmark)

    Nie, Jinzhe; Fang, Lei; Olesen, Bjarne W.

    2014-01-01

    Based on the air purification capacity of regenerative silica gel rotor, an innovative clean air heat pump (CAHP) was designed, developed and investigated through experimental studies. The CAHP integrated air purification, dehumidification and heating/cooling in one unit. A prototype of the CAHP...

  19. 76 FR 36917 - Clean Air Act Operating Permit Program; Petition for Objection to State Operating Permit for...

    Science.gov (United States)

    2011-06-23

    ... AGENCY Clean Air Act Operating Permit Program; Petition for Objection to State Operating Permit for TransAlta Centralia Generation, LLC--Coal- Fired Power Plant AGENCY: Environmental Protection Agency (EPA... to a citizen petition asking EPA to object to an operating permit issued by the Southwest Clean...

  20. Cleaning Products and Air Fresheners: Emissions and ResultingConcentrations of Glycol Ethers and Terpenoids

    Energy Technology Data Exchange (ETDEWEB)

    Singer, Brett C.; Destaillat, Hugo; Hodgson, Alfred T.; Nazaroff,William W.

    2005-08-01

    Experiments were conducted to quantify emissions and concentrations of glycol ethers and terpenoids from cleaning product and air freshener use in a 50-m{sup 3} room ventilated at {approx}0.5 h{sup -1}. Five cleaning products were applied full-strength (FS); three were additionally used in dilute solution. FS application of pine-oil cleaner (POC) yielded 1-h concentrations of 10-1300 {micro}g m{sup -3} for individual terpenoids, including {alpha}-terpinene (90-120), d-limonene (1000-1100), terpinolene (900-1300), and {alpha}-terpineol (260-700). One-hour concentrations of 2-butoxyethanol and/or dlimonene were 300-6000 {micro}g m{sup -3} after FS use of other products. During FS application including rinsing with sponge and wiping with towels, fractional emissions (mass volatilized/dispensed) of 2-butoxyethanol and d-limonene were 50-100% with towels retained, {approx}25-50% when towels were removed after cleaning. Lower fractions (2-11%) resulted from dilute use. Fractional emissions of terpenes from FS use of POC were {approx}35-70% with towels retained, 20-50% with towels removed. During floor cleaning with dilute solution of POC, 7-12% of dispensed terpenes were emitted. Terpene alcohols were emitted at lower fractions: 7-30% (FS, towels retained), 2-9% (FS, towels removed), and 2-5% (dilute). During air-freshener use, d-limonene, dihydromyrcenol, linalool, linalyl acetate, and {beta}-citronellol were emitted at 35-180 mg d{sup -1} over three days while air concentrations averaged 30-160 {micro}g m{sup -3}.

  1. Proceedings of the 21st DOE/NRC nuclear air cleaning conference; Volume 2, Sessions 9--16

    Energy Technology Data Exchange (ETDEWEB)

    First, M.W. [ed.] [Harvard Univ., Boston, MA (United States). Harvard Air Cleaning Lab.

    1991-02-01

    The 21st meeting of the Department of Energy/Nuclear Regulatory Commission (DOE/NRC) Nuclear Air Cleaning Conference was held in San Diego, CA on August 13--16, 1990. The proceedings have been published as a two volume set. Volume 2 contains sessions covering adsorbents, nuclear codes and standards, modelling, filters, safety, containment venting and a review of nuclear air cleaning programs around the world. Also included is the list of attendees and an index of authors and speakers. (MHB)

  2. Removal of mercury vapor from ambient air of dental clinics using an air cleaning system based on silver nanoparticles

    Directory of Open Access Journals (Sweden)

    Chiman Saeidi

    2015-06-01

    Full Text Available Background & objective: Mercury is a toxic and bio-accumulative pollutant that has adverse effects on environmental and human health. There have been a number of attempts to regulate mercury emissions tothe atmosphere. Silver nanoparticles are a number of materials that have highly potential to absorb mercury and formation of mercury amalgam.The aim of this study is removal of mercury vapors in the dental clinic using a n a ir cleaning system based on silver nanoparticles. Methods: In this study, silver nanoparticles coated on the bed of foam and chemical and structural properties were determined using a number of methods such as UV-VIS-NIR spectroscopy and Scanning Electron Microscope (SEM connected the X-ray Emission Spectroscopy Energy (EDS. The a ir cleaning system efficiency to remove of the mercury vapor in simulated conditions in the laboratory and real conditions in the dental clinicwere measured by Cold Vapor Atomic Absorption Spectroscopy (CVAAS. Results: The images of SEM, showed that average sizeof silver nanoparticles in colloidal solution was ∼ 30nm and distribution of silver nanoparticles coated on foam was good. EDS spectrum confirmed associated the presence of silver nanoparticles coated on foam. The significantly difference observed between the concentration of mercury vapor in the off state (9.43 ± 0.342 μg.m-3 and on state (0.51 ± 0.031μg.m-3 of the a ir cleaning system. The mercury vapor removal efficiencyof the a ir cleaning system was calculated 95%. Conclusion : The air cleaning system based on foam coated by silver nanoparticles, undertaken to provide the advantages such as use facilitating, highly efficient operational capacity and cost effective, have highly sufficiency to remove mercury vapor from dental clinics.

  3. Energy efficient biological air cleaning for farm stable ventilation; Energieffektiv biologisk luftrensning til staldventilation

    Energy Technology Data Exchange (ETDEWEB)

    Groenborg Nicolaisen, C.; Hansen, Mads P.R. [Teknologisk Institut, Aarhus (Denmark); Stroem, J.; Soerensen, Keld [DXT. Danish Exergy Technology A/S, Skoerping (Denmark); Goetke, C. [Lokalenergi Aarhus, Viby J. (Denmark); Morsing, S.; Soerensen, Lars C. [SKOV A/S, Roslev (Denmark); Ladegaerd Jensen, T.; Pedersen, Poul [Videncenter for svineproduktion, Copenhagen (Denmark)

    2013-05-01

    The project has been designed to reduce energy consumption for air purification by 30% while having a payback period of maximum 3 years. The project has achieved very significant results which are far above the target. Particularly satisfying is the wide range of new components that are launched in late 2012. By implementing the newly developed system at 100% cleaning (LPC 13 ventilators and Dynamic multistep control) in relation to Best Practice (SKOV's original system with DA600 fans) in a concrete pigsty, a saving of 61% and a simple payback of 1.7 years is achieved. Similarly, it is found that the energy used for pump operation can be reduced by 37% with the new Dynamic sprinkling control. At 20% cleaning a potential saving of 15% per year and a payback period of between 0 and 5 years was found, which is dependent on the desired performance as the capacities in the bio-filter's upper capacity range between 26 thousand to 30 thousand m3 / h entails costs for an additional extraction unit in the new solution. Furthermore, the newly developed components proved highly suitable for standard installations without air cleaning where a savings potential is 53% and the payback period 1.5 years. Product-wise, the project formed the basis for the development of: 1. New energy-efficient ventilation units (LPC11, 12,13) that are suitable for air purification; 2. A new energy-saving control principle (Dynamic Multi-Step) which is particularly suitable for low-energy ventilators; 3. A new energy-saving flow measurement system for ventilating ducts (Dynamic air to the central exhaust); 4. An energy-saving pressure control in common ducts (pressure control as a function of outside temperature); 5. Proposal for a new energy-saving pump operation for sprinkling of biological filters (Dynamic sprinkling). (LN)

  4. An introduction to the design, commissioning and operation of nuclear air cleaning systems for Qinshan Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Xinliang Chen; Jiangang Qu; Minqi Shi [Shanghai Nuclear Engineering Research and Design Institute (China)] [and others

    1995-02-01

    This paper introduces the design evolution, system schemes and design and construction of main nuclear air cleaning components such as HEPA filter, charcoal adsorber and concrete housing etc. for Qinshan 300MW PWR Nuclear Power Plant (QNPP), the first indigenously designed and constructed nuclear power plant in China. The field test results and in-service test results, since the air cleaning systems were put into operation 18 months ago, are presented and evaluated. These results demonstrate that the design and construction of the air cleaning systems and equipment manufacturing for QNPP are successful and the American codes and standards invoked in design, construction and testing of nuclear air cleaning systems for QNPP are applicable in China. The paper explains that the leakage rate of concrete air cleaning housings can also be assured if sealing measures are taken properly and embedded parts are designed carefully in the penetration areas of the housing and that the uniformity of the airflow distribution upstream the HEPA filters can be achieved generally no matter how inlet and outlet ducts of air cleaning unit are arranged.

  5. New clean air efforts face tough challenges, say senators and former EPA administrators

    Science.gov (United States)

    Showstack, Randy

    2012-02-01

    With the U.S. Environmental Protection Agency (EPA) coming under repeated attack from some members of Congress and others for perceived heavy-handed regulatory actions, two moderate U.S. senators and two former EPA administrators recently noted the need for continued measures to improve air quality. However, they also acknowledged the difficulty in moving forward with new legislative efforts to revise the federal Clean Air Act to further reduce air pollution in the current polarized political climate. "Nobody who wants to see constructive changes [to the act] would dare touch it or propose it in the current climate," said former EPA administrator William Reilly at a 23 January forum sponsored by the World Resources Institute. Reilly, who served as EPA administrator from 1989 to 1992, noted that bipartisan congressional support had been key to addressing many environmental problems up until the mid-1990s.

  6. Interaction between Titles 2 and 3 of the Clean Air Act as amended, 1990

    Energy Technology Data Exchange (ETDEWEB)

    Szpunar, C.B.

    1996-02-01

    This report examines Some issues that would I affect the refining industry if the requirements for hazardous air pollutants set out in Title III of the Clean Air Act Amendments were to impede the market entrance of oxygenated fuels, as me; required by Title II. It describes the mandate for reformulated gasoline; considers gasoline characteristics in light of component shifts in refining; examines the supply of, demand for, and cost of various feedstocks and blendstocks; and identifies the emissions and atmospheric impacts that might result from the production and use of reformulated gasoline. Attention is focused on methanol and MTBE, two potential blendstocks that are also hazardous air pollutants, and on maximum achievable control technology standards, which might be applied to the stationary sources that produce them.

  7. Indoor secondary pollutants from cleaning product and air freshener use in the presence of ozone

    DEFF Research Database (Denmark)

    Singer, B.C.; Coleman, B.K.; Destaillats, H.

    2006-01-01

    This study investigated the formation of secondary pollutants resulting from household product use in the presence of ozone. Experiments were conducted in a 50-m(3) chamber simulating a residential room. The chamber was operated at conditions relevant to US residences in polluted areas during warm......-oil air freshener (AFR) was operated for several days. Cleaning products were applied realistically with quantities scaled to simulate residential use rates. Concentrations of organic gases and secondary organic aerosol from the terpene-containing consumer products were measured with and without ozone...... than 100 mu g m(-3)) in some experiments. Ozone consumption and elevated hydroxyl radical concentrations persisted for 10-12 h following brief cleaning events, indicating that secondary pollutant production can persist for extended periods. (c) 2006 Elsevier Ltd. All rights reserved....

  8. 40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

    Science.gov (United States)

    2010-07-01

    ... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and...

  9. The North Carolina Department of Environment and Natural Resources: clean land, water, and air for healthy people and communities.

    Science.gov (United States)

    Riegel, Lisa Diaz; Wakild, Charles; Boothe, Laura; Hildebrandt, Heather J; Nicholson, Bruce

    2012-01-01

    The North Carolina Department of Environment and Natural Resources works with communities and other agencies to sustain clean air, water, and land. Sustainability efforts include protecting air quality through community design, community enhancement through brownfields revitalization, community development strategies to protect water resources, and the integration of natural resource conservation.

  10. OH and HO2 chemistry in clean marine air during SOAPEX-2

    Directory of Open Access Journals (Sweden)

    R. Sommariva

    2004-01-01

    Full Text Available Model-measurement comparisons of HOx in extremely clean air ([NO] The free-radical chemistry was studied using a zero-dimensional box-model based upon the Master Chemical Mechanism (MCM. Two versions of the model were used, with different levels of chemical complexity, to explore the role of hydrocarbons upon free-radical budgets under very clean conditions. The "detailed" model was constrained to measurements of CO, CH4 and 17 NMHCs, while the "simple" model contained only the CO and CH4 oxidation mechanisms, together with inorganic chemistry. The OH and HO2 (HOx concentrations predicted by the two models agreed to within 5–10%. The model results were compared with the HOx concentrations measured by the FAGE (Fluorescence Assay by Gas Expansion technique during four days of clean Southern Ocean marine boundary layer (MBL air. The models overestimated OH concentrations by about 10% on two days and about 20% on the other two days. HO2 concentrations were measured during two of these days and the models overestimated the measured concentrations by about 40%. Better agreement with measured HO2 was observed by using data from several MBL aerosol measurements to estimate the aerosol surface area and by increasing the HO2 uptake coefficient to unity. This reduced the modelled HO2 overestimate by ~40%, with little effect on OH, because of the poor HO2 to OH conversion at the low ambient NOx concentrations. Local sensitivity analysis and Morris One-At-A-Time analysis were performed on the "simple" model, and showed the importance of reliable measurements of j(O1D and [HCHO] and of the kinetic parameters that determine the efficiency of O(1D to OH and HCHO to HO2 conversion. A 2σ standard deviation of 30–40% for OH and 25–30% for HO2 was estimated for the model calculations using a Monte Carlo technique coupled with Latin Hypercube Sampling (LHS.

  11. Air cleaning efficiency of deodorant materials under dynamic conditions: effect of air flow rate

    DEFF Research Database (Denmark)

    Mizutani, Chiyomi; Bivolarova, Mariya Petrova; Melikov, Arsen Krikor

    2014-01-01

    was evaluated as deodorant materials neutralising ammonia in air. The deodorant material efficiency was tested in a special experimental set-up consisting of a straight pipe section, an ammonia gas generator, a fan and a textile frame. The deodorant materials, placed in the pipe, were exposed to a flow of air...... mixed with ammonia gas at a concentration of 20 ppm and velocities of 0.05, 0.15, 0.3 and 1.2 m/s. The activated carbon fibers treated with acid had a high deodorizing effect for ammonia (0.8) at a velocity of 0.05 m/s. The deodorizing effect of this material decreased with the increase in the velocity....... The porous activated carbon fiber fabric did not have a deodorant effect....

  12. How can the Clean Development Mechanism contribute to better air quality?

    Energy Technology Data Exchange (ETDEWEB)

    Bakker, S.J.A. [ECN Policy Studies, Petten (Netherlands)

    2009-06-15

    Air pollutants and greenhouse gases are to a large extent emitted by the same sources, notably in the industry, transport and residential sectors. However, climate change mitigation is a global issue and is mostly driven by national and international policy. Local governments are in general more interested in improving urban air quality, which is posing serious health hazards across the globe. The Clean Development Mechanism (CDM) was designed to reduce greenhouse gas emissions, helping industrialised countries to achieve their targets under the Kyoto Protocol while contributing to sustainable development in developing countries. As of January 2009 over 4000 projects are in the pipeline. The CDM could be used by local governments and the private sector to finance projects that contribute to both climate change mitigation and better air quality. However, CDM projects in particularly the transport sector face a number of barriers. We identify the most important issues for such projects, as well as the lessons learnt and some recommendations based on four case studies in Asian cities related to biofuels and bus rapid transit systems. The main conclusions is that successful implementation of CDM projects beneficial for urban air quality depends on the applicability of approved CDM methodologies, the strong cooperation between project developers and local authorities, and the availability of data.

  13. Evaluation Clean Air Effects on Tehran City Residential Houses Price in 2009

    Directory of Open Access Journals (Sweden)

    Aghapour Sabbagi M.

    2011-06-01

    Full Text Available BackgroundsandObjectives: Environmental activitiesunknownprice and value caused establishing of some unique characteristics for mentioned commodities. One of these characteristics was existing gap between private and social cost and benefit. For assessing these activities different approaches include travel cost, willingness to pay and hedonic price had been suggested. According to Tehran's air pollution problem, in this study Hedonic approach had was used for the assessment of healthy air on Tehran's residential house price.Materials and Method : Hedonic approach is one of the methods that are used for evolution environmental goods. In this method, each good's price is estimated as a functions of that good`s properties. To gather this study information 300 questionnaires has been collected by random sampling from different area of Tehran.Result: Results revealed that activities in order to reduce air pollutions, in addition to environmental value have economical value form the point of view of consumers. Also, results show that willingness to pay of every Tehran's citizens for every square meter of house located in region with less pollution is between 1120 to 1350 thousands Rials.Conclusion: According to the obtained results can be said that, clean air as an environmental good from the viewpoint of consumers has economic value that can be calculated this value using methods such as Hedonic.

  14. Evaluating the Impact of Air Pollution on Human Health in China: the Price of Clean Air

    Science.gov (United States)

    Wang, X.; Mauzerall, D. L.; Hu, Y.; Russell, A. G.; Woo, J.; Streets, D. G.

    2003-12-01

    Population growth, rapid urbanization and economic development are contributing to increased energy consumption in China. One of the unintended consequences is poor air quality due to a lack of environmental controls. The coal dependent energy structure in China only worsens the situation. Quantification of the environmental costs resulting from air pollution is needed in order to provide a mechanism for making strategic energy policy that accounts for the life-cycle cost of energy use. However, few such studies have been conducted for China that examine the entire energy system. Here we examine the extent to which public health has been compromised due to elevated air pollution and how China could incorporate environmental costs into future energy and environmental policies. Taking the Shandong region in eastern China as a case study, we develop a high-resolution regional inventory for anthropogenic emissions of NOx, CO, PM2.5, PM10, VOCs, NH3 and SO2. SMOKE (Sparse Matrix Operator Kernel Emissions Modeling System) is used to process spatial and temporal distributions and chemical speciation of the regional emissions, MM5 (the Fifth-Generation NCAR/Penn State Meso-scale Model, Version 3) is used to generate meteorology and Models3/CMAQ (Community Multi-scale Air Quality Modeling System) is used to simulate ambient concentrations of particulates and other gaseous species in this region. We then estimate the mortality and morbidity in this region resulting from exposure to these air pollutants. We also estimate the monetary values associated with the resulting mortality and morbidity and quantify the contributions from various economic sectors (i.e. power generation, transportation, industry, residential and others). Finally, we examine the potential health benefits that adoption of best available or advanced energy (coal-based, in particular) and environmental technologies in different sectors could bring about. The results of these analyses are intended to provide

  15. Development of an air cleaning system for dissolving high explosives from nuclear warheads

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, W.; Wilson, K.; Staggs, K.; Wapman, D. [Lawrence Livermore National Lab., CA (United States)

    1997-08-01

    The Department of Energy (DOE) has a major effort underway in dismantling nuclear weapons. In support of this effort we have been developing a workstation for removing the high explosive (HE) from nuclear warheads using hot sprays of dimethyl sulfoxide (DMSO) solvent to dissolve the HE. An important component of the workstation is the air cleaning system that is used to contain DMSO aerosols and vapor and radioactive aerosols. The air cleaning system consists of a condenser to liquefy the hot DMSO vapor, a demister pad to remove most of the DMSO aerosols, a high efficiency particulate air (HEPA) filter to remove the remaining aerosols, an activated carbon filter to remove the DMSO vapor, and a final HEPA filter to meet the redundancy requirement for HEPA filters in radioactive applications. The demister pad is a 4{double_prime} thick mat of glass and steel fibers and was selected after conducting screening tests on promising candidates. We also conducted screening tests on various activated carbons and found that all had a similar performance. The carbon breakthrough curves were fitted to a modified Wheeler`s equation and gave excellent predictions for the effect of different flow rates. After all of the components were assembled, we ran a series of performance tests on the components and system to determine the particle capture efficiency as a function of size for dioctyl sebacate (DOS) and DMSO aerosols using laser particle counters and filter samples. The pad had an efficiency greater than 990% for 0.1 {mu}m DMSO particles. Test results on the prototype carbon filter showed only 70% efficiency, instead of the 99.9% in small scale laboratory tests. Thus further work will be required to develop the prototype carbon filter. 7 refs., 18 figs., 10 tabs.

  16. Clean air matters: an overview of traffic-related air pollution and pregnancy

    Science.gov (United States)

    Slovic, Anne Dorothée; Diniz, Carmen Simone; Ribeiro, Helena

    2017-01-01

    ABSTRACT The right to a healthy pregnancy and to giving birth in a safe environment is source of comprehensive research. Decent birth facilities, respect, and no discrimination are already recognized as fundamental rights, but an accurate look at the outdoor environment is required. Air pollution is a dangerous factor to pregnant women and newborns, many of whom highly exposed to traffic-related atmospheric pollutants in urban areas. Such exposure can lead to low birth weight and long-lasting effects, such as respiratory diseases and premature death. Thus, this commentary, based on the analysis of literature, presents the importance of the exposome concept and of epigenetics in identifying the role of the environment for better health conditions of pregnant women and newborns. In the final considerations, this study proposes the deepening of the subject and the mobilization in this regard, with a human rights-based approach to environmental health and to the increased awareness of pregnant women on the risks of air pollution and its effects on health. PMID:28225911

  17. OH and HO2 chemistry in clean marine air during SOAPEX-2

    Directory of Open Access Journals (Sweden)

    A. C. Lewis

    2004-01-01

    Full Text Available Model-measurement comparisons of HOx in extremely clean air ([NO]<3  ppt are reported. Measurements were made during the second Southern Ocean Photochemistry Experiment (SOAPEX-2, held in austral summer 1999 at the Cape Grim Baseline Air Pollution Station in north-western Tasmania, Australia. The free-radical chemistry was studied using a zero-dimensional box-model based upon the Master Chemical Mechanism (MCM. Two versions of the model were used, with different levels of chemical complexity, to explore the role of hydrocarbons upon free-radical budgets under very clean conditions. The "detailed" model was constrained to measurements of CO, CH4 and 15 NMHCs, while the "simple" model contained only the CO and  CH4 oxidation mechanisms, together with inorganic chemistry. The OH and HO2 (HOx concentrations predicted by the two models agreed to within 5–10%. The model results were compared with the HOx concentrations measured by the FAGE (Fluorescence Assay by Gas Expansion technique during four days of clean Southern Ocean marine boundary layer (MBL air. The models overestimated OH concentrations by about 10% on two days and about 20% on the other two days. HO2 concentrations were measured during two of these days and the models overestimated the measured concentrations by about 40%. Better agreement with measured HO2 was observed by using data from several MBL aerosol measurements to estimate the aerosol surface area and by increasing the HO2 uptake coefficient to unity. This reduced the modelled HO2 overestimate by ~40%, with little effect on OH, because of the poor HO2 to OH conversion at the low ambient NOx concentrations. Local sensitivity analysis and Morris One-At-A-Time analysis were performed on the "simple" model, and showed the importance of reliable measurements of j(O1D and [HCHO] and of the kinetic parameters that determine the efficiency of  O(1D to OH and HCHO to HO2 conversion. A 2σ standard deviation of 30–40% for OH and

  18. Sophisticated Clean Air Strategies Required to Mitigate Against Particulate Organic Pollution

    Science.gov (United States)

    Grigas, T.; Ovadnevaite, J.; Ceburnis, D.; Moran, E.; McGovern, F. M.; Jennings, S. G.; O’Dowd, C.

    2017-03-01

    Since the 1980’s, measures mitigating the impact of transboundary air pollution have been implemented successfully as evidenced in the 1980–2014 record of atmospheric sulphur pollution over the NE-Atlantic, a key region for monitoring background northern-hemisphere pollution levels. The record reveals a 72–79% reduction in annual-average airborne sulphur pollution (SO4 and SO2, respectively) over the 35-year period. The NE-Atlantic, as observed from the Mace Head research station on the Irish coast, can be considered clean for 64% of the time during which sulphate dominates PM1 levels, contributing 42% of the mass, and for the remainder of the time, under polluted conditions, a carbonaceous (organic matter and Black Carbon) aerosol prevails, contributing 60% to 90% of the PM1 mass and exhibiting a trend whereby its contribution increases with increasing pollution levels. The carbonaceous aerosol is known to be diverse in source and nature and requires sophisticated air pollution policies underpinned by sophisticated characterisation and source apportionment capabilities to inform selective emissions-reduction strategies. Inauspiciously, however, this carbonaceous concoction is not measured in regulatory Air Quality networks.

  19. Development of an emergency air-cleaning system for liquid-metal reactors

    Energy Technology Data Exchange (ETDEWEB)

    Owen, R.K.

    1980-11-01

    A novel air cleaning concept has been developed for potential use in venting future commercial liquid metal fast breeder reactor containment buildings in the unlikely event of postulated core disruptive accidents. The passive concept consists of a submerged gravel bed to collect the bulk of particulate contaminates carried by the vented gas. A fibrous scrubber could be combined with the submerged gravel scrubber to enhance collection efficiencies for the smaller sized particles. The submerged gravel scrubber is unique in that water flow through the packed bed is induced by the gas flow, eliminating the need for an active liquid pump. In addition, design gas velocities through the packed bed are 10 to 20 times higher than for a conventional sand bed filter.

  20. Extended-life nuclear air cleaning filters via dynamic exclusion prefilters

    Energy Technology Data Exchange (ETDEWEB)

    Wright, S.R.; Crouch, H.S.; Bond, J.H. [Micro Composite Materials Corp., Durham, NC (United States)

    1997-08-01

    The primary objective of this investigation was to ascertain if a dynamic, self-cleaning particulate exclusion precleaner, designed for relatively large dust removal (2 to 100+ {mu}m diameter particles) from helicopter turbine inlets, could be extended to submicron filtration. The improved device could be used as a prefilter for HEPA filtration systems, significantly increasing service life. In nuclear air cleaning, its use would reduce the amount of nuclear particulate matter that would otherwise be entrapped in the HEPA filter cartridge/panel, causing fouling and increased back pressure, as well as requiring subsequent disposal of the contaminated media at considerable expense. A unique (patent-pending) mechanical separation device has recently been developed to extract particulate matter from fluid process streams based on a proprietary concept called Boundary Layer Momentum Transfer (BLMT). The device creates multiple boundary layers that actively exclude particles from entering the perimeter of the device, while allowing air to traverse the boundaries relatively unimpeded. A modified two-dimensional (2-D) computerized flow simulation model was used to assist in the prototype design. Empirical results are presented from particle breakthrough and AP experiments obtained from a reduced-scale prototype filter. Particles larger than 0.23 {mu}m were actively excluded by the prototype, but at a higher pressure drop than anticipated. Experimental data collected indicates that the filter housing and the inlet flow configuration may contribute significantly to improvements in device particle separation capabilities. Furthermore, preliminary experiments have shown that other downstream pressure drop considerations (besides those just across the spinning filtration disks) must be included to accurately portray the AP across the device. Further detailed quantitative investigations on a larger scale (1,000 CFM) prototype are warranted. 3 refs., 5 figs., 2 tabs.

  1. 40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

    Science.gov (United States)

    2010-07-01

    ... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the...

  2. 40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

    Science.gov (United States)

    2010-07-01

    ... wood wastes, clean lumber, and/or yard waste? (a) Use Method 9 of 40 CFR part 60, Appendix A to... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber...

  3. 40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9...

  4. 40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

    Science.gov (United States)

    2010-07-01

    ... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... Only Wood Waste, Clean Lumber, and Yard Waste § 60.2972 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of appendix A of...

  5. Whole house particle removal and clean air delivery rates for in-duct and portable ventilation systems.

    Science.gov (United States)

    Macintosh, David L; Myatt, Theodore A; Ludwig, Jerry F; Baker, Brian J; Suh, Helen H; Spengler, John D

    2008-11-01

    A novel method for determining whole house particle removal and clean air delivery rates attributable to central and portable ventilation/air cleaning systems is described. The method is used to characterize total and air-cleaner-specific particle removal rates during operation of four in-duct air cleaners and two portable air-cleaning devices in a fully instrumented test home. Operation of in-duct and portable air cleaners typically increased particle removal rates over the baseline rates determined in the absence of operating a central fan or an indoor air cleaner. Removal rates of 0.3- to 0.5-microm particles ranged from 1.5 hr(-1) during operation of an in-duct, 5-in. pleated media filter to 7.2 hr(-1) for an in-duct electrostatic air cleaner in comparison to a baseline rate of 0 hr(-1) when the air handler was operating without a filter. Removal rates for total particulate matter less than 2.5 microm in aerodynamic diameter (PM2.5) mass concentrations were 0.5 hr(-1) under baseline conditions, 0.5 hr(-1) during operation of three portable ionic air cleaners, 1 hr(-1) for an in-duct 1-in. media filter, 2.4 hr(-1) for a single high-efficiency particle arrestance (HEPA) portable air cleaner, 4.6 hr(-1) for an in-duct 5-in. media filter, 4.7 hr(-1) during operation of five portable HEPA filters, 6.1 hr(-1) for a conventional in-duct electronic air cleaner, and 7.5 hr(-1) for a high efficiency in-duct electrostatic air cleaner. Corresponding whole house clean air delivery rates for PM2.5 attributable to the air cleaner independent of losses within the central ventilation system ranged from 2 m3/min for the conventional media filter to 32 m3/min for the high efficiency in-duct electrostatic device. Except for the portable ionic air cleaner, the devices considered here increased particle removal indoors over baseline deposition rates.

  6. In pursuit of clean air: a data book of problems and strategies at the state level. Supplement

    Energy Technology Data Exchange (ETDEWEB)

    Garvey, D.B.; Moser, S.B.; Streets, D.G.

    1980-08-01

    The Clean Air Act Amendments of 1977 and EPA regulations set stringent requirements for the control of emissions in areas where the National Ambient Air Quality Standards were being exceeded. This supplement updates a previous five-volume summary of nonattainment area designations and attainment strategies of the states as of July 1, 1980. It also contains maps of PSD Class I areas and additional information on coal production, coal reserves, and coal quality.

  7. Exemptions for hookah bars in clean indoor air legislation: a public health concern.

    Science.gov (United States)

    Noonan, Devon

    2010-01-01

    Popularity of waterpipe smoking or hookah smoking in the United States has been growing for some time now among youth and young adults. Currently, many cities and states have exemptions that allow hookah bars to remain in operation despite the passage of clean indoor air legislation. From a public health perspective this is concerning for many reasons. One public health concern with the increase in popularity of this type of tobacco use is the associated health effects. Another concern is that hookah smoke produces a sweet smelling aroma making it less obvious that patrons and employees of hookah bars are inhaling noxious fumes from mainstream smoke, as well as the toxins from the charcoal that is used to heat the tobacco. The purpose of this paper is to discuss smoke-free air legislation in relation to hookah use, the public health implications of exempting hookah bars from current smoke-free legislation, and implications for the public health nurse in protecting the public from the dangers of second-hand smoke, and limiting this new form of tobacco use.

  8. 76 FR 11280 - Notice of Lodging of an Amendment to Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2011-03-01

    ... February 14, 2011, a proposed Amendment to the consent decree in United States et al. v. Lafarge North... states or state agencies against Lafarge North America, Inc.'s, Lafarge Midwest, Inc.'s, and Lafarge Building Materials, Inc.'s (``Lafarge's'') for alleged violations of the Clean Air Act (``CAA'' or...

  9. 77 FR 38830 - Notice of Lodging of an Amendment to Consent Decree Under the Clean Air Act

    Science.gov (United States)

    2012-06-29

    ... June 25, 2012, a proposed Second Amendment to the consent decree in United States et al. v. Lafarge... and twelve states or state agencies against Lafarge North America, Inc., Lafarge Midwest, Inc., and Lafarge Building Materials, Inc. (``Lafarge'') for alleged violations of the Clean Air Act (``CAA''...

  10. 77 FR 20396 - Request for Nominations of Candidates to the EPA's Clean Air Scientific Advisory Committee (CASAC...

    Science.gov (United States)

    2012-04-04

    ...; water quantity; water re-use; ecosystem services; community environmental health; sustainability... independent scientific and technical peer review, consultation, advice and recommendations directly to the EPA... under the Clean Air Act (CAA) Amendments, the chartered CASAC reviews and offers scientific advice...

  11. 77 FR 73459 - California State Motor Vehicle Pollution Control Standards; Notice of Waiver of Clean Air Act...

    Science.gov (United States)

    2012-12-10

    ... AGENCY California State Motor Vehicle Pollution Control Standards; Notice of Waiver of Clean Air Act..., challenging the need for CARB's own motor vehicle pollution control program based on lack of compelling and... Administrator shall waive preemption for California to enforce new motor vehicle emissions standards...

  12. 76 FR 53452 - Clean Air Act Operating Permit Program; Response to Petition To Reopen the 2001 Title V Permit...

    Science.gov (United States)

    2011-08-26

    ... the U.S. Court of Appeals for Third Circuit. Under the terms of a settlement agreement between EPA and... Circuit Court of Appeals is the appropriate court of appeals. Section 307(b)(1) also requires that any.... Judicial Review Section 307(b)(1) of the Clean Air Act indicates which Federal Courts of Appeals have...

  13. 75 FR 75463 - Clean Air Act Operating Permit Program; Petition To Object to Title V Permit for Luke Paper...

    Science.gov (United States)

    2010-12-03

    ... AGENCY Clean Air Act Operating Permit Program; Petition To Object to Title V Permit for Luke Paper... permit issued by the Maryland Department of the Environment (MDE) on January 22, 2009 to Luke Paper... to the issuance of the proposed title V permit for Luke Paper Company because of, (1)...

  14. 40 CFR 62.15395 - Does this subpart require me to obtain an operating permit under title V of the Clean Air Act?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Does this subpart require me to obtain an operating permit under title V of the Clean Air Act? 62.15395 Section 62.15395 Protection of... require me to obtain an operating permit under title V of the Clean Air Act? Yes. If you are subject...

  15. Plants + microbes: Innovative food crop systems that also clean air and water

    Science.gov (United States)

    Nelson, Mark; Wolverton, B. C.

    The limitations that will govern bioregenerative life support applications in space, especially volume and weight, make multi-purpose systems advantageous. This paper outlines two systems which utilize plants and associated microbial communities of root or growth medium to both produce food crops and clean air and water. Underlying these approaches are the large numbers and metabolic diversity of microbes associated with roots and found in either soil or other suitable growth media. It is known that most biogeochemical cycles have a microbial link, and the ability of microbes to metabolize virtually all trace gases, whether of technogenic or biogenic origin, have long been established. Wetland plants and soil/media also been extensively researched for their ability to purify wastewaters of all kinds of potential water pollutants, from nutrients like N and P, to heavy metals and a range of complex industrial pollutants. There is a growing body of research on the ability of higher plants to purify air and water. Associated benefits of these approaches is that by utilizing natural ecological processes, the cleansing of air and water can be done with little or no energy inputs. Soil and root microorganisms respond to changing pollutant types by an increase of the types of organisms with the capacity to use these compounds. Thus living systems have an extraordinary adaptive capacity as long as the starting populations are sufficiently diverse. It is known that tightly sealed environments, from office buildings to spacecraft, can have hundreds or even thousands of potential air pollutants, depending on the materials and machines enclosed. Human waste products carry a plethora of microbes can are readily used in the process of converting its organic load to forms that can be utilized by green plants. Having endogenous means of responding to changing air and water quality conditions represents safety factors which operate without the need for human direction. We will

  16. Plants + soil/wetland microbes: Food crop systems that also clean air and water

    Science.gov (United States)

    Nelson, Mark; Wolverton, B. C.

    2011-02-01

    The limitations that will govern bioregenerative life support applications in space, especially volume and weight, make multi-purpose systems advantageous. This paper outlines two systems which utilize plants and associated microbial communities of root or growth medium to both produce food crops and clean air and water. Underlying these approaches are the large numbers and metabolic diversity of microbes associated with roots and found in either soil or other suitable growth media. Biogeochemical cycles have microbial links and the ability of microbes to metabolize virtually all trace gases, whether of technogenic or biogenic origin, has long been established. Wetland plants and the rootzone microbes of wetland soils/media also been extensively researched for their ability to purify wastewaters of a great number of potential water pollutants, from nutrients like N and P, to heavy metals and a range of complex industrial pollutants. There is a growing body of research on the ability of higher plants to purify air and water. Associated benefits of these approaches is that by utilizing natural ecological processes, the cleansing of air and water can be done with little or no energy inputs. Soil and rootzone microorganisms respond to changing pollutant types by an increase of the types of organisms with the capacity to use these compounds. Thus living systems have an adaptive capacity as long as the starting populations are sufficiently diverse. Tightly sealed environments, from office buildings to spacecraft, can have hundreds or even thousands of potential air pollutants, depending on the materials and equipment enclosed. Human waste products carry a plethora of microbes which are readily used in the process of converting its organic load to forms that can be utilized by green plants. Having endogenous means of responding to changing air and water quality conditions represents safety factors as these systems operate without the need for human intervention. We review

  17. Potential exposure to silver nanoparticles during spraying preparation for air-conditioning cleaning

    Directory of Open Access Journals (Sweden)

    Elżbieta Jankowska

    2013-02-01

    Full Text Available Background: Unique properties of engineered nanomaterials (ENMs and products made of them have contributed to a rapid progress in the production and application of ENMs in different branches of industry and in factories with different production scale. Bearing in mind that nano-objects (nanoplates, nanofibres, nanoparticles, emitted during ENM production and application, can cause many diseases, even those not yet recognized, extensive studies have been carried all over the world to assess the extent of exposure to nano-objects at workstations and related health effects in workers employed in ENM manufacture and application processes. Material and Methods: The study of potential exposure to silver nanoparticles contained in the preparation for airconditioning cleaning (Nano Silver from Amtra Sp. z o.o. involved the determination of concentrations and size distribution of particles, using different devices, allowing for tracing changes in a wide range of dimensions, from nano-size (10 nm to micrometrsize (10 µm, of the particles which are usually inhaled by humans. Results and Conclusions: The results of the study shows that even during a short-term spraying of Nano Silver preparation (for 10 s at the distance of 52 cm from the place of preparation spraying - particles of 10 nm-10 µm can be emitted into in the air. During a three-fold preparation spraying in similar conditions differences in concentration increase were observed, but in each case the particles remained in the air for a relatively long time. Med Pr 2013;64(1:57–67

  18. Effects of welding fumes on nuclear air cleaning system carbon adsorber banks

    Energy Technology Data Exchange (ETDEWEB)

    Roberson, P.W. [Duke Power Company, Huntersville, NC (United States)

    1997-08-01

    Standard Technical Specifications for nuclear air cleaning systems include requirements for surveillance tests following fire, painting, or chemical release in areas communicating with the affected system. To conservatively implement this requirement, many plants categorize welding as a chemical release process, and institute controls to ensure that welding fumes do not interact with carbon adsorbers in a filter system. After reviewing research data that indicated welding had a minimal impact on adsorber iodine removal efficiency, further testing was performed with the goal of establishing a welding threshold. It was anticipated that some quantity of weld electrodes could be determined that had a corresponding detrimental impact on iodine removal efficiency for the exposed adsorber. This value could be used to determine a conservative sampling schedule that would allow the station to perform laboratory testing to ensure system degradation did not occur without a full battery of surveillance tests. A series of tests was designed to demonstrate carbon efficiency versus cumulative welding fume exposure. Three series of tests were performed, one for each of three different types of commonly used weld electrodes. Carbon sampling was performed at baseline conditions, and every five pounds of electrode thereafter. Two different laboratory tests were performed for each sample; one in accordance with ASTM 3803/1989 at 95% relative humidity and 30 degrees C, and another using the less rigorous conditions of 70% relative humidity and 80 degrees C. Review of the test data for all three types of electrodes failed to show a significant correlation between carbon efficiency degradation and welding fume exposure. Accordingly, welding is no longer categorized as a `chemical release process` at McGuire Nuclear Station, and limits on welding fume interaction with ventilation systems have been eliminated. 4 refs., 3 figs., 1 tab.

  19. Allowance trading under the Clean Air Act: Who should regulate, and when?

    Energy Technology Data Exchange (ETDEWEB)

    Lock, R. [LeBoeuf, Lamb, Leiby & MacRae, Washington, DC (United States)

    1993-07-01

    The goal of this paper is to explore how compliance with the Clean Air Act Amendments of 1990 (CAAA), especially Title IV and emission trading under it, will affect the current relationship between state and federal regulation. It is difficult, with the limited experience we have had under Title IV, to be definitive about or to be a very strong advocate of too many policy positions. What may be most helpful at this point is to identify where the difficult issues in state/federal relations might arise; and then to explore ways in which tensions might be either avoided or resolved. One anticipated conclusion is that a traditional regulatory mindset could be very destructive if applied to this new area of oversight without due sensitivity to what Congress is trying to achieve in Title IV. That concern pervaded the early legislative debates; and it persists today. Title IV presents some unique challenges to state regulators and will require some creative solutions and fresh thinking if the goals of Congress are to be realized and the full benefits that allowance trading can offer are to be reaped by electricity consumers. In the ultimate analysis, Title IV amounts to a massive internalization of the external costs imposed on society by acid rain deposition. (This places in serious question the notion of additional externality {open_quotes}adders{close_quotes} for sulfur dioxide (SO{sub 2}) and nitrous oxide (NO{sub x}) at the state level for utility supply planning purposes.) The whole point of Title IV is to give those directly charged with compliance, namely power producers, the maximum flexibility to pursue least-cost compliance solutions. Perhaps the biggest single factor in how well they do this will be how state regulators respond to their compliance and allowance trading initiatives.

  20. Regulatory policy issues and the Clean Air Act: Issues and papers from the state implementation workshops

    Energy Technology Data Exchange (ETDEWEB)

    Rose, K. [ed.; Burns, R.E.

    1993-07-01

    The National Regulatory Research Institute (NRRI), with funding from the US Environmental Protection Agency (EPA) and the US Department of Energy (DOE), conducted four regional workshops` on state public utility commission implementation of the Clean Air Act Amendments of 1990 (CAAA). The workshops had four objectives: (1) to discuss key issues and concerns on CAAA implementation, (2) to encourage a discussion among states on issues of common interests, (3) to attempt to reach consensus, where possible, on key issues, and (4) to provide the workshop participants with information and materials to assist in developing state rules, orders, and procedures. From the federal perspective, a primary goal was to ensure that workshop participants return to their states with a comprehensive background and understanding of how state commission actions may affect implementation of the CAAA and to be able to provide guidance to their jurisdictional utilities. It was hoped that this would reduce some of the uncertainty utilities face and assist in the development of an efficient allowance market. This report is divided into two main sections. In Section II, eleven principal issues are identified and discussed. These issues were chosen because they were either the most frequently discussed or they were related to the questions asked in response to the speakers` presentations. This section does not cover all the issues relevant to state implementation nor all the issues discussed at the workshops; rather, Section II is intended to provide an overview of the,planning, ratemaking, and multistate issues. Part III is a series of workshop papers presented by some of the speakers. Individual papers have been cataloged separately.

  1. We Care for Clean Air! The Contribution of ACCENT to Education and Communication

    Science.gov (United States)

    Schuepbach, Eva; Brimblecombe, Peter; Gross, Krisjanis; Jacobs, Mark J.; Ladstätter-Weißenmayer, Annette; Moussiopoulos, Nicolas; Slini, Theodora; Übelis, Arnolds; Uherek, Elmar

    2010-05-01

    A new booklet on: "We Care for Clean Air! Motivating the Next Generation of Atmospheric Scientists" (ISBN 978-88-95665-01-6) as recently published by the education community in ACCENT (www.accent-network.org/portal/education) is presented. Promoting creative and innovative researchers and teachers and encouraging the next generation to move into the field were among the key issues in ACCENT "Training and Education" (T&E). During the 5-year programme, a wealth of educational events (e.g., workshops) and programmes (e.g., "ACCENT FAR EAST") were organized and tools developed for teachers and learners at Universities and Schools around the globe. Activities such as National ACCENT Days or Cafés Scientifiques also targeted stakeholders, policy makers and the general public to increase the expertise in atmospheric composition change to a common level across Europe. The volume introduces the integrated learning environment, high-quality tools and methods for air quality and climate change science education created by ACCENT T&E, and provides an overview on the unbiased scientific information that has been didactically translated based on knowledge available from ongoing research projects.The core messages are that (i) the translation of complex issues in atmospheric composition and climate change science to non-scientists should be scientifically acceptable and that (ii) scientists should stay in control of the translation process. After the publication of the 4th Assessment Report of the Intergovernmental Panel for Climate Change (IPCC) in 2007, ACCENT intensified its efforts to reach greater visibility and distribute the body of know-how, skills and competencies within the networked community of atmospheric scientists in the World Wide Web. For example, a Special Issue of the "Global Change Magazine for Schools" on IPCC 2007 contains a compact introduction to the basics of global warming for direct application in the classroom, also focusing on uncertainties and

  2. Improvement of self-cleaning type air filter%自洁式空气过滤器的改进

    Institute of Scientific and Technical Information of China (English)

    王鹏

    2012-01-01

    The self-cleaning type air filter is fitted before air inlet pipe of air compressor completed for air separation plant. The domestic-made carriage has low service life, and in case of highly wet air the filter paper is liable to stick, which lowers the filtering efficiency, results in frequent repair of air compressor repair, and seriously impairs prolonged stable run of air separation plant. The service life of carriage of self-cleaning type air filter is extended and the filtering efficiency is improved through use of the non-woven filtering cotton blended with compound fiber, the carriage made of compound fiber, and the imported filter paper, adjustment of its programmable controller, and change of its back-blowing pressure and air supply. Here, the work principle of self- cleaning type air filter is briefed, the problems during its operation process are analyzed, and the implementation process and economic benefits of the improvement measures are described.%空分设备配套空压机进气管前设置自洁式空气过滤器,由于国内生产的滤筒使用寿命短,遇含湿量大的空气时滤纸易黏连,进而影响过滤效率,导致空压机检修频繁,严重影响了空分设备长周期稳定运行。通过增加复合纤维无纺滤棉,选用复合纤维滤筒和进口滤纸,调整自洁式空气过滤器的编程控制仪,以及改变反吹压力和反吹气源,达到延长自洁式空气过滤器的滤筒寿命和提高过滤效率的目的。简述自洁式空气过滤器的工作原理,分析其使用过程中存在的问题,阐述改进措施的实施过程及取得的经济效益。

  3. California Clean Air Act: A compliance strategy for the City of San Diego`s non-emergency fleet

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-31

    Historically, parts of California have had the worst air quality in the nation. The California Energy Commission began experimenting with alternate fuels in the 1970`s in an effort to reduce harmful automobile emissions and hence, improve air quality. It is recognized that the costs to California which result from our air quality problems are immense. Ten to twenty billion dollars each year is the estimated damage in terms of health impacts, materials damages, lost agricultural crop output and forest damages. As the California population increases and health care costs escalate, the total monetary damages from air pollution will increase. The California Energy Commission goal to improve air quality became a mandate in 1988 with the passage of the California Clean Air Act (CCAA). The CCAA requires a revised air quality strategy for the San Diego district since we do not meet State air quality standards for smog, carbon monoxide and nitrogen dioxide. Smog remains San Diego`s major air quality problem, even though the annual number of days each year over the Federal standard has been reduced by 55 percent in the past ten years. Ten years ago about two-thirds of San Diego`s smog was transported from Los Angeles. Today more than 60 per cent of the days San Diego exceeds the State standard are from locally generated smog. It is estimated that 57% of the reactive hydrocarbon emissions (which react with nitrogen dioxide in the presence of sunlight to form smog) is from cars, trucks and buses. The Air Pollution Control District (part of the County of San Diego) is the office that the Air Resources Board has put in charge of creating regulations and designing strategy to reduce polluting emissions. The purpose of this project is to determine the full cost of acquiring and operating a municipal fleet which meets the mandates of the California Clean Air Act. With that information, a plan to meet the Clear Air Act (CCAA) requirements can be formulated by local government.

  4. Methods for air cleaning and protection of building occupants from airborne pathogens

    DEFF Research Database (Denmark)

    Bolashikov, Zhecho Dimitrov; Melikov, Arsen Krikor

    2009-01-01

    germicidal irradiation (UVGI), photocatalytic oxidation (PCO), plasmacluster ions and other technologies for air disinfection and purification from pathogens are analyzed with respect to currently used air distribution principles. The importance of indoor air characteristics, such as temperature, relative...

  5. Seeing Through Smoke: Sorting through the Science and Politics in the Making of the 1956 British Clean Air Act (Invited)

    Science.gov (United States)

    Kenny, D. A.

    2010-12-01

    The 1952 “Killer Smog” left over 4000 citizens of Greater London dead in a single week. It was a highly visible environmental disaster, which pinned the British government with responsibility over factory and domestic coal smoke pollution. Within four years of the Smog, the British parliament passed the 1956 Clean Air Act, which was designed primarily to prevent the release of dark smoke from the chimneys of private dwellings and factories. This act is considered a significant turning point in the history of environmental regulation. Through the analysis of confidential documents from government ministries and Members of Parliament, my research has focused on how decisions were made following this man-made environmental catastrophe. The primary focus of this presentation will be to explore why the British government appeared lethargic in the face of its long-standing coal pollution problem and why it finally passed the first clean air act in the world. In this case, establishing responsibility and organizing research were the major time constraints on policy action. In the months following the 1952 Smog, government departments passed off responsibility and quarreled over jurisdiction in the smog matter. Ministries held responsible for air pollution jointly established the Committee on Air Pollution to find a solution to urban smog. In the years following, the Committee on Air Pollution compiled research on the health effects and economic impact of air pollution, deriving its information from a variety of sources. In its 1954 final report, the committee named smoke and sulfur dioxide the most likely culprits of the 1952 deaths, and it recommended the elimination of smoke-producing coal from the British market, a major change to how the British fueled their homes and factories. The resulting 1956 Clean Air Act was the product of numerous compromises over the economic, political, and social issues present in Great Britain at the time. The British government

  6. Robust self-cleaning surfaces that function when exposed to either air or oil

    OpenAIRE

    Lu, Y.

    2015-01-01

    Superhydrophobic self-cleaning surfaces are based on the surface micro/nanomorphologies; however, such surfaces are mechanically weak and stop functioning when exposed to oil. We have created an ethanolic suspension of perfluorosilane-coated titanium dioxide nanoparticles that forms a paint that can be sprayed, dipped, or extruded onto both hard and soft materials to create a self-cleaning surface that functions even upon emersion in oil. Commercial adhesives were used to bond the paint to va...

  7. Clean Air for Anchorage and Fairbanks: Curriculum for Grades 1-6.

    Science.gov (United States)

    South East Regional Resource Center, Juneau, AK.

    Through the 10 lessons in this guide, elementary school students can be introduced to the characteristics of air, methods of air pollution control, air movement, and the health effects of polluted air. A directory of field trip sites and a list of teacher resources is included. Contained in each lesson plan are a materials list, general…

  8. Effects of indoor air purification by an air cleaning system (Koala technology) on semen parameters in male factor infertility: results of a pilot study.

    Science.gov (United States)

    Paradisi, R; Vanella, S; Barzanti, R; Cani, C; Battaglia, C; Seracchioli, R; Venturoli, S

    2009-06-01

    A number of studies indicated a clear decline in semen quality in the past 30-50 years and there is accumulating evidence that this decline might result from exposure to high levels of air pollution. To examine the impact of environment on male reproductive ability, we undertook for the first time a pilot study on semen quality of infertile men exposed to purification of indoor air. Ten subjects with a history of unexplained male infertility and poor semen quality were exposed for at least 1 year to a cleaning indoor air system (Koala technology). The key feature of this air purifier is the unique innovative multiple filtering system. The treatment of total purification of indoor air showed neither improvements in semen parameters nor variation in reproductive hormones (P = N.S.), but induced an evident increase (P indoor air does not seem enough to improve semen quality, although the increase in leucocytic concentrations could indicate an activation of the role of immunosurveillance in a purified indoor air environment.

  9. Fighting ambient air pollution and its impact on health: from human rights to the right to a clean environment.

    Science.gov (United States)

    Guillerm, N; Cesari, G

    2015-08-01

    Clean air is one of the basic requirements of human health and well-being. However, almost nine out of 10 individuals living in urban areas are affected by air pollution. Populations living in Africa, South-East Asia, and in low- and middle-income countries across all regions are the most exposed. Exposure to outdoor air pollution ranks as the ninth leading risk factor for mortality, killing 3.2 million people each year, especially young children, the elderly, persons with lung or cardiovascular disease, those who work or exercise outdoors and low-income populations. In October 2013, the International Agency for Research on Cancer (IARC) classified outdoor air pollution as carcinogenic to humans, calling air pollution 'a major environmental health problem'. Human rights and environmental norms are powerful tools to combat air pollution and its impact on health. The dependence of human rights on environmental quality has been recognised in international texts and by human rights treaty bodies. The growing awareness of the environment has already yielded considerable legislative and regulatory output. However, the implementation of standards remains a pervasive problem. In the fight against violations of norms, citizens have a crucial role to play. We discuss the relevance of a yet to be proclaimed standalone right to a healthy environment.

  10. Robust self-cleaning surfaces that function when exposed to either air or oil

    Science.gov (United States)

    Lu, Yao; Sathasivam, Sanjayan; Song, Jinlong; Crick, Colin R.; Carmalt, Claire J.; Parkin, Ivan P.

    2015-03-01

    Superhydrophobic self-cleaning surfaces are based on the surface micro/nanomorphologies; however, such surfaces are mechanically weak and stop functioning when exposed to oil. We have created an ethanolic suspension of perfluorosilane-coated titanium dioxide nanoparticles that forms a paint that can be sprayed, dipped, or extruded onto both hard and soft materials to create a self-cleaning surface that functions even upon emersion in oil. Commercial adhesives were used to bond the paint to various substrates and promote robustness. These surfaces maintained their water repellency after finger-wipe, knife-scratch, and even 40 abrasion cycles with sandpaper. The formulations developed can be used on clothes, paper, glass, and steel for a myriad of self-cleaning applications.

  11. Repellent materials. Robust self-cleaning surfaces that function when exposed to either air or oil.

    Science.gov (United States)

    Lu, Yao; Sathasivam, Sanjayan; Song, Jinlong; Crick, Colin R; Carmalt, Claire J; Parkin, Ivan P

    2015-03-06

    Superhydrophobic self-cleaning surfaces are based on the surface micro/nanomorphologies; however, such surfaces are mechanically weak and stop functioning when exposed to oil. We have created an ethanolic suspension of perfluorosilane-coated titanium dioxide nanoparticles that forms a paint that can be sprayed, dipped, or extruded onto both hard and soft materials to create a self-cleaning surface that functions even upon emersion in oil. Commercial adhesives were used to bond the paint to various substrates and promote robustness. These surfaces maintained their water repellency after finger-wipe, knife-scratch, and even 40 abrasion cycles with sandpaper. The formulations developed can be used on clothes, paper, glass, and steel for a myriad of self-cleaning applications.

  12. 77 FR 54382 - Revisions of Five California Clean Air Act Title V Operating Permits Programs

    Science.gov (United States)

    2012-09-05

    ... pollution control, Carbon dioxide, Carbon dioxide equivalents, Greenhouse gases, Hydrofluorocarbons... revisions to the Operating Permits (Title V) programs of the Monterey Bay Unified Air Pollution Control District (MBUAPCD), San Luis Obispo County Air Pollution Control District (SLOCAPCD), Santa Barbara...

  13. 75 FR 1770 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2010-01-13

    ... Health and Environment, Air Pollution Division, to the Public Service of Colorado to operate the Hayden... Department of Public Health and Environment, Air Pollution Division, to the Public Service of Colorado...

  14. 77 FR 5518 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2012-02-03

    ... Public Health and Environment, Air Pollution Division, to CF&I Steel, d/b/a EVRAZ Rocky Mountain Steel... by the Colorado Department of Public Health and Environment, Air Pollution Division, to CF&I Steel,...

  15. Preliminary calculations for the CAFE project (Clean Air For Europe); Calculs preparatoires pour la strategie thematique CAFE (Clean Air For Europe)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-09-15

    The European Commission decided in 2001 an analysis program to reduce the atmospheric emissions. This report presents different limit scenari for France in 2020 (the reference scenari and the MTFR scenari, Maximum Technically Feasible Reduction), optimized scenari calculated by the RAINS model (Regional Air Pollution Information and Simulation), the costs of the scenari calculated with RAINS and the cost-benefit analysis of the strategy CAFE. From the study results, the benefits are higher than the costs, even with the most ambitious scenari. At an european level the emission reduction strategies have no effect on the employment but an impact on the Gross Domestic Product (decrease between 0,04 % and 0,12 % in function of the scenari). (A.L.B.)

  16. CLEAN-ROADS project: air quality considerations after the application of a novel MDSS on winter road maintenance activities

    Science.gov (United States)

    Pretto, Ilaria; Malloci, Elisa; Tonidandel, Gabriele; Benedetti, Guido; Di Napoli, Claudia; Piazza, Andrea; Apolloni, Roberto; Cavaliere, Roberto

    2016-04-01

    With this poster we present the environmental benefit on air quality derived by the application of the CLEAN-ROADS pilot project. The CLEAN-ROADS project addresses the problem of the environmental pollution caused by de-icing salts during winter road maintenance activities in the Province of Trento (Italy). A demonstrative Maintenance Decision Support System (MDSS) has been developed in order to improve the intervention procedures of the road management service. Specifically it aims to optimize the efficiency of how available resources (e.g., salt consumption) are currently used while guaranteeing the current level of road safety. The CLEAN-ROADS project has been tested and validated on a test area located in a valley bottom (Adige Valley), where the highest optimization margins are to be expected. The project supports current road maintenance practices, which has proved to be reliable and accurate, with a new scalable and energy-efficient road monitoring system. This system is based on a network of road weather stations (road weather information system, RWIS) installed on the test route. It is capable to collect real-time data about the road conditions and to perform short-term and now-cast road weather forecasts, which actively integrate weather data and bulletins covering the target area [1]. This poster presents the results obtained from a three-year monitoring activity with the aim to (1) determine the impact of de-icing salts on air quality and (2) quantify the improvements obtained by the application of the CLEAN-ROADS project on air quality. The Ambient Air Quality and Cleaner Air for Europe Directive (2008/50/EC) states that contributions to exceedances of particulate matter PM10 limit values that are attributable to road winter salting may be subtracted when assessing compliance with air quality limit values, once provided that reasonable measures have been taken to lower concentrations [2]. As the de-icing salts used in road maintenance are mainly based

  17. 3D Air Quality and the Clean Air Interstate Rule: Lagrangian Sampling of CMAQ Model Results to Aid Regional Accountability Metrics

    Science.gov (United States)

    Fairlie, T. D.; Szykman, Jim; Pierce, Robert B.; Gilliland, A. B.; Engel-Cox, Jill; Weber, Stephanie; Kittaka, Chieko; Al-Saadi, Jassim A.; Scheffe, Rich; Dimmick, Fred; Tikvart, Joe

    2008-01-01

    The Clean Air Interstate Rule (CAIR) is expected to reduce transport of air pollutants (e.g. fine sulfate particles) in nonattainment areas in the Eastern United States. CAIR highlights the need for an integrated air quality observational and modeling system to understand sulfate as it moves in multiple dimensions, both spatially and temporally. Here, we demonstrate how results from an air quality model can be combined with a 3d monitoring network to provide decision makers with a tool to help quantify the impact of CAIR reductions in SO2 emissions on regional transport contributions to sulfate concentrations at surface monitors in the Baltimore, MD area, and help improve decision making for strategic implementation plans (SIPs). We sample results from the Community Multiscale Air Quality (CMAQ) model using ensemble back trajectories computed with the NASA Langley Research Center trajectory model to provide Lagrangian time series and vertical profile information, that can be compared with NASA satellite (MODIS), EPA surface, and lidar measurements. Results are used to assess the regional transport contribution to surface SO4 measurements in the Baltimore MSA, and to characterize the dominant source regions for low, medium, and high SO4 episodes.

  18. Clean Air for Anchorage and Fairbanks: Curriculum for Grades 7-12.

    Science.gov (United States)

    South East Regional Resource Center, Juneau, AK.

    Ten lessons on air and air pollution comprise this guide for secondary school teachers. Among the topics addressed are pollutants, health effects, weather inversions, personal involvement, and automobile emissions. Particular emphasis is placed upon problems in Alaskan cities. Lesson plans contain a materials list, background information,…

  19. Cleaning up the air: effectiveness of air quality policy for SO2 and NOx emissions in China

    Science.gov (United States)

    van der A, Ronald J.; Mijling, Bas; Ding, Jieying; Elissavet Koukouli, Maria; Liu, Fei; Li, Qing; Mao, Huiqin; Theys, Nicolas

    2017-02-01

    Air quality observations by satellite instruments are global and have a regular temporal resolution, which makes them very useful in studying long-term trends in atmospheric species. To monitor air quality trends in China for the period 2005-2015, we derive SO2 columns and NOx emissions on a provincial level with improved accuracy. To put these trends into perspective they are compared with public data on energy consumption and the environmental policies of China. We distinguish the effect of air quality regulations from economic growth by comparing them relatively to fossil fuel consumption. Pollutant levels, per unit of fossil fuel, are used to assess the effectiveness of air quality regulations. We note that the desulfurization regulations enforced in 2005-2006 only had a significant effect in the years 2008-2009, when a much stricter control of the actual use of the installations began. For national NOx emissions a distinct decreasing trend is only visible from 2012 onwards, but the emission peak year differs from province to province. Unlike SO2, emissions of NOx are highly related to traffic. Furthermore, regulations for NOx emissions are partly decided on a provincial level. The last 3 years show a reduction both in SO2 and NOx emissions per fossil fuel unit, since the authorities have implemented several new environmental regulations. Despite an increasing fossil fuel consumption and a growing transport sector, the effects of air quality policy in China are clearly visible. Without the air quality regulations the concentration of SO2 would be about 2.5 times higher and the NO2 concentrations would be at least 25 % higher than they are today in China.

  20. Market effects of environmental regulation: coal, railroads, and the 1990 Clean Air Act

    Energy Technology Data Exchange (ETDEWEB)

    Busse, M.R.; Keohane, N.O. [University of California Berkeley, Berkeley, CA (United States)

    2007-01-01

    Many environmental regulations encourage the use of 'clean' inputs. When the suppliers of such an input have market power, environmental regulation will affect not only the quantity of the input used but also its price. We investigate the effect of the Title IV emissions trading program for sulfur dioxide on the market for low-sulfur coal. We find that the two railroads transporting coal were able to price discriminate on the basis of environmental regulation and geographic location. Delivered prices rose for plants in the trading program relative to other plants, and by more at plants near a low-sulfur coal source.

  1. 76 FR 58808 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2011-09-22

    ... CONTACT: Geoffrey L. Wilcox, Air and Radiation Law Office (2344A), Office of General Counsel, U.S...; fax number (202) 564-5601; e-mail address: wilcox.geoffrey@epa.gov . SUPPLEMENTARY INFORMATION:...

  2. 78 FR 26028 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2013-05-03

    ... CONTACT: Geoffrey L. Wilcox, Air and Radiation Law Office (2344A), Office of General Counsel, U.S...; fax number (202) 564-5603; email address: wilcox.geoffrey@epa.gov . SUPPLEMENTARY INFORMATION:...

  3. 76 FR 71027 - Proposed Settlement Agreements, Clean Air Act Citizen Suit

    Science.gov (United States)

    2011-11-16

    ... of the Colorado Department of Public Health and Environment, Air Pollution Control Division regarding... Department of Public Health and Environment regarding the issuance of a renewed title V permit for...

  4. Qualitative Analysis and Study of the Microorganisms in Clean Air within Clean Room of the Pharmaceutical Industry%医药工业洁净室洁净空气微生物定性分析与探讨

    Institute of Scientific and Technical Information of China (English)

    吕洪浩; 李俊杰; 徐慰倬

    2012-01-01

    ObjGCtive To study the distribution of the microorganisms in clean air within clean room of the pharmaceutical industry. Methods Test method for settling microbe was used in the clean air of some clean rooms. The microorganisms isolated were analysed by morphological observation, physiological and biochemical tests and 16S rDNA sequence analysis. Results A strain of actinomycete, four strains of fungi and ten strains of bacteria were derived in the experiment. Conclusion The clean air mainly consists of bacteria, a small amount of fungi and actinomycetes. Professionals of enterprise should master the distribution of bacteria, fungi and actinomycetes, analyze the causes of formation of the colony forming unit and take targeted methods of control for the environment of the clean room to guarantee the quality of products.%目的 探讨医药工业洁净室洁净空气中微生物分布情况.方法 对部分洁净室洁净空气进行沉降菌检测,采用形态学观察,生理生化反应检测以及16S rDNA序列测定等技术对微生物进行分析.结果 通过实验共获得放线菌1株,真菌4株,细菌10株.结论 一般洁净空气中以细菌为主,有少量真菌及放线菌,企业生产者应掌握这些菌的分布情况,分析这些菌落形成的原因,对洁净室环境做出针对性控制手段以保证产品质量.

  5. The effects of Title IV of the Clean Air Act amendments of 1990 on electric utilities: An update

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report presents data and analyses related to Phase I implementation of the Clean Air Act Amendment by electric utilities. It describes the strategies used to comply with the Acid Rain Program in 1995, the effect of compliance on sulfur dioxide emissions levels, the cost of compliance, and the effects of the program on coal supply and demand. The first year of Phase I demonstrated that the market-based sulfur dioxide emissions control system could achieve significant reductions in emissions at lower than expected costs. Some utilities reduced aggregate emissions below legal requirements due to economic incentives; other utilities purchased additional allowances to avoid noncompliance. More than half of the utilities switched to or blended with lower sulfur coal, due to price reductions in the coal market which were partially due to the allowance trading program. 21 figs., 20 tabs.

  6. A review of the current geographic distribution of and debate surrounding electronic cigarette clean air regulations in the United States.

    Science.gov (United States)

    Kadowaki, Joy; Vuolo, Mike; Kelly, Brian C

    2015-01-01

    In this article, we present the results of a systematic review of state, county, and municipal restrictions on the use of electronic cigarettes (e-cigarettes) in public spaces within the United States, alongside an overview of the current legal landscape. The lack of federal guidance leaves lower-level jurisdictions to debate the merits of restrictions on use in public spaces without sufficient scientific research. As we show through a geographic assessment of restrictions, this has resulted in an inconsistent patchwork of e-cigarette use bans across the United States of varying degrees of coverage. Bans have emerged over time in a manner that suggests a "bottom up" diffusion of e-cigarette clean air policies. Ultimately, the lack of clinical and scientific knowledge on the risks and potential harm reduction benefits has led to precautionary policymaking, which often lacks grounding in empirical evidence and results in spatially uneven diffusion of policy.

  7. 75 FR 38519 - Proposed Consent Decree, Clean Air Act Citizen Suit

    Science.gov (United States)

    2010-07-02

    ...-00946 PJH (N.D. C.A.). On March 5, 2010, Plaintiff filed a complaint to compel the U. S. Environmental... County Air Pollution Control District Rule 420'' (Imperial Rule 420), a State implementation plan (SIP... Rule 420. In addition, the proposed consent decree requires that following signature on such notice...

  8. 78 FR 27234 - Notification of a Public Teleconference of the Clean Air Scientific Advisory Committee (CASAC...

    Science.gov (United States)

    2013-05-09

    ... Development of the Integrated Science Assessment (ISA) for NOX--Health Criteria. DATES: The public teleconference will be held on Wednesday, June 5, 2013 from 1:00 p.m. to 4:00 p.m. (Eastern Time). Location: The... on the scientific and technical aspects of issues related to the criteria for air quality...

  9. Environmental health in China: progress towards clean air and safe water.

    Science.gov (United States)

    Zhang, Junfeng; Mauzerall, Denise L; Zhu, Tong; Liang, Song; Ezzati, Majid; Remais, Justin V

    2010-03-27

    Environmental risk factors, especially air and water pollution, are a major source of morbidity and mortality in China. Biomass fuel and coal are burned for cooking and heating in almost all rural and many urban households, resulting in severe indoor air pollution that contributes greatly to the burden of disease. Many communities lack access to safe drinking water and sanitation, and thus the risk of waterborne disease in many regions is high. At the same time, China is rapidly industrialising with associated increases in energy use and industrial waste. Although economic growth from industrialisation has improved health and quality of life indicators, it has also increased the release of chemical toxins into the environment and the rate of environmental disasters, with severe effects on health. Air quality in China's cities is among the worst in the world, and industrial water pollution has become a widespread health hazard. Moreover, emissions of climate-warming greenhouse gases from energy use are rapidly increasing. Global climate change will inevitably intensify China's environmental health troubles, with potentially catastrophic outcomes from major shifts in temperature and precipitation. Facing the overlap of traditional, modern, and emerging environmental dilemmas, China has committed substantial resources to environmental improvement. The country has the opportunity to address its national environmental health challenges and to assume a central role in the international effort to improve the global environment.

  10. 40 CFR Appendix H to Subpart A of... - Clean Air Act Amendments of 1990 Phaseout Schedule for Production of Ozone-Depleting Substances

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Clean Air Act Amendments of 1990 Phaseout Schedule for Production of Ozone-Depleting Substances H Appendix H to Subpart A of Part 82... STRATOSPHERIC OZONE Production and Consumption Controls Pt. 82, Subpt. A, App. H Appendix H to Subpart A of...

  11. 40 CFR 62.14830 - Does this subpart require me to obtain an operating permit under title V of the Clean Air Act?

    Science.gov (United States)

    2010-07-01

    ... operating permit unless you meet the relevant requirements specified in 40 CFR 62.14525(a) through (h) and (j) through (o) and all of the requirements specified in 40 CFR 62.14531. ... an operating permit under title V of the Clean Air Act? 62.14830 Section 62.14830 Protection...

  12. Validation of the criteria for initiating the cleaning of heating, ventilation, and air-conditioning (HVAC) ductwork under real conditions.

    Science.gov (United States)

    Lavoie, Jacques; Marchand, Geneviève; Cloutier, Yves; Lavoué, Jérôme

    2011-08-01

    Dust accumulation in the components of heating, ventilation, and air-conditioning (HVAC) systems is a potential source of contaminants. To date, very little information is available on recognized methods for assessing dust buildup in these systems. The few existing methods are either objective in nature, involving numerical values, or subjective in nature, based on experts' judgments. An earlier project aimed at assessing different methods of sampling dust in ducts was carried out in the laboratories of the Institut de recherche Robert-Sauvé en santé et en sécurité du travail (IRSST). This laboratory study showed that all the sampling methods were practicable, provided that a specific surface-dust cleaning initiation criterion was used for each method. However, these conclusions were reached on the basis of ideal conditions in a laboratory using a reference dust. The objective of this present study was to validate these laboratory results in the field. To this end, the laboratory sampling templates were replicated in real ducts and the three sampling methods (the IRSST method, the method of the U.S. organization National Air Duct Cleaner Association [NADCA] and that of the French organization Association pour la Prévention et l'Étude de la Contamination [ASPEC]) were used simultaneously in a statistically representative number of systems. The air return and supply ducts were also compared. Cleaning initiation criteria under real conditions were found to be 6.0 mg/100 cm(2) using the IRSST method, 2.0 mg/100 cm(2) using the NADCA method, and 23 mg/100 cm(2) using the ASPEC method. In the laboratory study, the criteria using the same methods were 6.0 for the IRSST method, 2.0 for the NADCA method, and 3.0 for the ASPEC method. The laboratory criteria for the IRSST and NADCA methods were therefore validated in the field. The ASPEC criterion was the only one to change. The ASPEC method therefore allows for the most accurate evaluation of dust accumulation in HVAC

  13. Photocatalytic equipment with nitrogen-doped titanium dioxide for air cleaning and disinfecting

    Science.gov (United States)

    Son Le, Thanh; Buu Ngo, Quoc; Dung Nguyen, Viet; Chau Nguyen, Hoai; Hien Dao, Trong; Tin Tran, Xuan; Kabachkov, E. N.; Balikhin, I. L.

    2014-03-01

    Nitrogen-doped TiO2 nanoparticle photocatalysts were synthesized by a sol-gel procedure using tetra-n-butyl orthotitanate as a titanium precursor and urea as a nitrogen source. Systematic studies for the preparation parameters and their impact on the material's structure were carried out by multiple techniques: thermogravimetric and differential scanning calorimetric analysis, x-ray diffraction, scanning electron microscope, transmission electron microscopy, energy dispersive x-ray spectroscopy and UV-Vis diffuse reflectance spectrophotometry showed that the nitrogen-doped TiO2 calcined at 500 °C for 3 h exhibited a spherical form with a particle size about 15-20 nm and crystal phase presented a mixture of 89.12% anatase. The obtained product was deposited on a porous quartz tube (D = 74 mm l = 418 mm) to manufacture an air photocatalytic cleaner as a prototype of the TIOKRAFT company's equipment. The created air cleaner was able to remove 60% of 10 ppm acetone within 390 min and degrade 98.5% of bacteria (total aerobic bacteria and fungi, 300 cfu m-3) within 120 min in a 10 m3 box. These photodegradation activities of N-TiO2 are higher than that of the commercial nano-TiO2 (Skyspring Inc., USA, particle size of 5-10 nm).

  14. Determination of the Clean Air Delivery Rate (CADR) of Photocatalytic Oxidation (PCO) Purifiers for Indoor Air Pollutants Using a Closed-Loop Reactor. Part I: Theoretical Considerations.

    Science.gov (United States)

    Dumont, Éric; Héquet, Valérie

    2017-03-06

    This study demonstrated that a laboratory-scale recirculation closed-loop reactor can be an efficient technique for the determination of the Clean Air Delivery Rate (CADR) of PhotoCatalytic Oxidation (PCO) air purification devices. The recirculation closed-loop reactor was modeled by associating equations related to two ideal reactors: one is a perfectly mixed reservoir and the other is a plug flow system corresponding to the PCO device itself. Based on the assumption that the ratio between the residence time in the PCO device and the residence time in the reservoir τP/τR tends to 0, the model highlights that a lab closed-loop reactor can be a suitable technique for the determination of the efficiency of PCO devices. Moreover, if the single-pass removal efficiency is lower than 5% of the treated flow rate, the decrease in the pollutant concentration over time can be characterized by a first-order decay model in which the time constant is proportional to the CADR. The limits of the model are examined and reported in terms of operating conditions (experiment duration, ratio of residence times, and flow rate ranges).

  15. Preservation of atomically clean silicon surfaces in air by contact bonding

    DEFF Research Database (Denmark)

    Grey, Francois; Ljungberg, Karin

    1997-01-01

    When two hydrogen-passivated silicon surfaces are placed in contact under cleanroom conditions, a weak bond is formed. Cleaving this bond under ultrahigh vacuum (UHV) conditions, and observing the surfaces with low energy electron diffraction and scanning tunneling microscopy, we find that the or......When two hydrogen-passivated silicon surfaces are placed in contact under cleanroom conditions, a weak bond is formed. Cleaving this bond under ultrahigh vacuum (UHV) conditions, and observing the surfaces with low energy electron diffraction and scanning tunneling microscopy, we find...... reconstruction from oxidation in air, Contact bonding opens the way to novel applications of reconstructed semiconductor surfaces, by preserving their atomic structure intact outside of a UHV chamber. (C) 1997 American Institute of Physics....

  16. Clean air. Measures against fine dust and nitrogen oxide; Luftreinhalteplanung. Massnahmen gegen Feinstaub und Stickstoffoxide

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-10-15

    Within the meeting of the Bavarian State Ministry of the Environment (Hof, Federal Republic of Germany) on 23rd October, 2012, the following lectures were held: (1) Future development of emissions and immission in Germany (Johanna Appelhans); (2) Air pollution control in urban areas - Example Stuttgart (Ulrich Reuter); (3) Green zones in Munich and Augsburg - Results from the efficiency analysis 2012 (Manfred Ertl); (4) Photocatalytic efficiency of titanium dioxide - Pilot experiment Fulda (Marita Mang); (5) Emission behaviour of Euro V/5 and VI/6 vehicles in real operation (Stefan Hausberger); (6) Reduction of particles and NO{sub x} by means of Euro VI commercial vehicles (Stefan Kamm); (7) Possibilities of retrofitting at vehicles for the reduction of emissions of fine dust and nitrous oxides (Michael Himmen); (8) Measures for reduction of emissions at construction machinery (Hinrich Helms); (9) ChimCat/circledR - Catalytic reduction of emissions (Martin Pley); (10) Improvement of the immission behaviour at the Airport Munich (Hermann Blomeyer).

  17. Combining active chilled beams and air-cleaning technologies to improve the indoor climate in offices

    DEFF Research Database (Denmark)

    Ardkapan, Siamak Rahimi; Afshari, Alireza; Bergsøe, Niels Christian

    2013-01-01

    of air in offices. For this purpose, a mechanical filter with low pressure drop was selected for testing in a laboratory environment. The measurements included tests of the filter in a ductwork to study the efficiency of the filter. Moreover, the combined system of the filter and a chilled beam...... was tested in a room. The efficiency of the mechanical filter to remove ultrafine particles was examined using pure wax candles and salt as sources of emission of particles. The measurements in the duct showed that the efficiency of the filter ranged between 54% and 78% and that the pressure loss was less...... than 5 Pa (0.104 Ibf /ft2). Furthermore, the measurement results of the combined system showed that adding the filter accelerated the removal rate of the particles by 2 h-1. However, the efficiency of the chilled beam in exchanging heat was reduced by 38%....

  18. Parametric Evaluation of an Innovative Ultra-Violet PhotocatalyticOxidation (UVPCO) Air Cleaning Technology for Indoor Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, Alfred T.; Sullivan, Douglas P.; Fisk, William J.

    2005-10-31

    An innovative Ultra-Violet Photocatalytic Oxidation (UVPCO) air cleaning technology employing a semitransparent catalyst coated on a semitransparent polymer substrate was evaluated to determine its effectiveness for treating mixtures of volatile organic compounds (VOCs) representative of indoor environments at low, indoor-relevant concentration levels. The experimental UVPCO contained four 30 by 30-cm honeycomb monoliths irradiated with nine UVA lamps arranged in three banks. A parametric evaluation of the effects of monolith thickness, air flow rate through the device, UV power, and reactant concentrations in inlet air was conducted for the purpose of suggesting design improvements. The UVPCO was challenged with three mixtures of VOCs. A synthetic office mixture contained 27 VOCs commonly measured in office buildings. A building product mixture was created by combining sources including painted wallboard, composite wood products, carpet systems, and vinyl flooring. The third mixture contained formaldehyde and acetaldehyde. Steady state concentrations were produced in a classroom laboratory or a 20-m{sup 3} chamber. Air was drawn through the UVPCO, and single-pass conversion efficiencies were measured from replicate samples collected upstream and downstream of the reactor. Thirteen experiments were conducted in total. In this UVPCO employing a semitransparent monolith design, an increase in monolith thickness is expected to result in general increases in both reaction efficiencies and absolute reaction rates for VOCs oxidized by photocatalysis. The thickness of individual monolith panels was varied between 1.2 and 5 cm (5 to 20 cm total thickness) in experiments with the office mixture. VOC reaction efficiencies and rates increased with monolith thickness. However, the analysis of the relationship was confounded by high reaction efficiencies in all configurations for a number of compounds. These reaction efficiencies approached or exceeded 90% for alcohols, glycol

  19. Clean air plans and action plans: perspectives from the viewpoint of environmental and public health; Luftreinhalteplaene und Aktionsplaene - eine Bewertung aus umweltmedizinischer Sicht

    Energy Technology Data Exchange (ETDEWEB)

    Eikmann, T.; Herr, C. [Inst. fuer Hygiene und Umweltmedizin, Universitaetsklinikum Giessen und Marburg, Justus-Liebig-Univ. Giessen, Giessen (Germany); [Technische Univ. Dreden, Pirna (Germany). Inst. fuer Abfallwirtschaft und Altlasten; Koeckler, H. [Center for Environmental Systems Research (CESR), Univ. Kassel (Germany); [Mentec GmbH, Aue/Sa. (Germany); Nieden, A. zur [Inst. fuer Hygiene und Umweltmedizin, Universitaetsklinikum Giessen und Marburg, Justus-Liebig-Univ. Giessen, Giessen (Germany); FG Stadtklimatologie, Univ. Kassel (Germany); Katzschner, L. [FG Stadtklimatologie, Univ. Kassel (Germany); [INTECUS Dresden GmbH (Germany); Schimmelpfennig, M. [Gesundheitsamt der Stadt Kassel (Germany); Eikmann, S. [GUK - Gesellschaft fuer Umwelttoxikologie und Krankenhaushygiene mbH, Wetzlar (Germany)

    2005-07-01

    The present discussion on the health effects associated with airborne fine particulate matter has lead to an increased public interest in the general framework of compilation and evaluation of clean air plans and actions plans. While the surveys of the ''old'' clean air plans of the 80ies and 90ies of the last century relied on assessment of direct and indirect effects of air pollution on human health (and ecology), theses surveys are not part of the ''new'' clean air plans according to European law. This reduction of surveys and actions directed at threshold compliance only, abandons assessing, i.e., documentation and evaluation the health status and quality of life of populations. Assessment of individual and focus group specific sensibility and vulnerability becomes possible once health related, sociodemographic and environmental data are combined. By this, unequal life chance, i.e., unimpaired health as well as reasonable strategies towards minimizing environmental injustice can be identified. As of yet it is unclear, to what extend quality of life and quality of environment of populations living in air polluted areas are attributable to socioeconomic factors. Likewise, it is not known to which degree the environmental quality of individuals and families is self determined. This has to be considered especially for children, immigrants and women. These issues i.e., environmental justice/injustice should be considered in future projects on the development of clean air plans and especially actions plans derived thereof. Scientists, government officials and physicians working in field of preventive or environmental medicine cannot agree to a limitation of the cautionary principle to the bare compliance with thresholds. (orig.)

  20. 中央空调管道清洗机器人控制系统设计%Design of central air conditioning duct cleaning robot control system

    Institute of Scientific and Technical Information of China (English)

    何琴

    2011-01-01

    In order to solve the problems of central air conditioning duct diameter non-standard and the difficulty of the duct cleaning,the automatic centering technology was investigated. After analysing the central air conditioning duct cleaning robot control system,adopting a modular design thought, taking ATmega64 microcontroller as the control core,the relations between modules were established. A method was presented to the central air conditioning duct cleaning robot control system design. The cleaning technology was evaluated based on the existing cleaning technology. The results show that the cleaning robot can achieve automatic centering to adapt different pipe diameters to finish cleaning tasks, provide a broad application prospects for central air conditioning duct cleaning technology.%为解决中央空调管道清洗难及管径不规范等问题,将自动定心技术应用到管道清洗机器人中,开展了中央空调管道清洗机器人控制系统方案分析与设计.采用模块化的设计思想,以ATmega64单片机为控制核心,建立了各个功能模块之间的关系,实现了中央空调管道清洗机器人整个控制系统的方案设计.在现有的中央空调管道清洗技术基础上,对相关研究成果进行了对比分析及评价.研究结果表明,所设计的清洗机器人能够实现自动定心以适应不同的空调管径,完成清洗作业,为中央空调管道清洗技术提供了广阔的应用前景.

  1. Proceedings of the Clean Air Foundation's shifting mobility workshop

    Energy Technology Data Exchange (ETDEWEB)

    Serafini, E. [Clean Air Foundation, Toronto, ON (Canada)

    2004-07-01

    This workshop brought together organizations with transportation-related initiatives underway across Ontario. The objective of the workshop was to identify strategic options for developing and implementing effective transportation-related public education and outreach initiatives, as well as to identify barriers and opportunities for public participation in sustainable transportation programs and create opportunities for collaboration to maximize the efficiency of existing initiatives. Attendees included representatives from federal, provincial, municipal and regional governments, non-government organizations and the private sector from across Ontario. Three themes were identified: (1) activities focused on encouraging the shift from traveling in single occupant vehicles to transit, autosharing, trains, bicycles and carpooling, (2) activities focused on encouraging consumers to choose more fuel efficient and lower emission vehicles and fuels, and (3) activities focused on encouraging the motoring public to change habits that will increase fuel efficiency and lower emissions, such as not idling their vehicle and monitoring tire pressure. Keynote and panel presentations showcased existing collaborative sustainable transportation initiatives, including integrated transportation systems in Germany. In addition, a summary of outcomes from Pollution Probe's Transportation, Air Issues and Human Health conference was presented in order to provide strategic options for the future and to highlight barriers and opportunities. Strategy sessions were held to allow participants the opportunity to identify specific areas of collaboration. The Smart Commute Initiative was discussed. Emerging automobile technologies were discussed by the Canadian Vehicle Manufacturer's Association. Issues concerning educational programs in schools and in the workplace were examined, as well as the challenges of achieving a system of integrated and sustainable urban transportation. tabs

  2. Air pollution-related health and climate benefits of clean cookstove programs in Mozambique

    Science.gov (United States)

    Anenberg, Susan C.; Henze, Daven K.; Lacey, Forrest; Irfan, Ans; Kinney, Patrick; Kleiman, Gary; Pillarisetti, Ajay

    2017-02-01

    Approximately 95% of households in Mozambique burn solid fuels for cooking, contributing to elevated indoor and outdoor fine particulate matter (PM2.5) concentrations and subsequent health and climate impacts. Little is known about the potential health and climate benefits of various approaches for expanding the use of cleaner stoves and fuels in Mozambique. We use state-of-the-science methods to provide a first-order estimation of potential air pollution-related health and climate benefits of four illustrative scenarios in which traditional cooking fires and stoves are displaced by cleaner and more efficient technologies. For rural areas, we find that a 10% increase in the number of households using forced draft wood-burning stoves could achieve >2.5 times more health benefits from reduced PM2.5 exposure (200 avoided premature deaths and 14 000 avoided disability adjusted life years, DALYs, over a three-year project lifetime) compared to natural draft stoves in the same households, assuming 70% of households use the new technology for both cases. Expanding use of LPG stoves to 10% of households in five major cities is estimated to avoid 160 premature deaths and 11 000 DALYs from reduced PM2.5 exposure for a three-year intervention, assuming 60% of households use the new stove. Advanced charcoal stoves would achieve ∽80% of the PM2.5-related health benefits of LPG stoves. Approximately 2%–5% additional health benefits would result from reduced ambient PM2.5, depending on the scenario. Although climate impacts are uncertain, we estimate that all scenarios would reduce expected climate change-related temperature increases from continued solid fuel use by 4%–6% over the next century. All results are based on an assumed adjustment factor of 0.8 to convert from laboratory-based emission reduction measurements to exposure reductions, which could be optimistic in reality given potential for continued use of the traditional stove. We conclude that cleaner cooking

  3. US-China Clean Energy Research Center on Building Energy Efficiency: Materials that Improve the Cost-Effectiveness of Air Barrier Systems

    Energy Technology Data Exchange (ETDEWEB)

    Hun, Diana E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-12-01

    The US–China Clean Energy Research Center (CERC) was launched in 2009 by US Energy Secretary Steven Chu, Chinese Minister of Science and Technology Wan Gang, and Chinese National Energy Agency Administrator Zhang Guobao. This 5-year collaboration emerged from the fact that the United States and China are the world’s largest energy producers, energy consumers, and greenhouse gas emitters, and that their joint effort could have significant positive repercussions worldwide. CERC’s main goal is to develop and deploy clean energy technologies that will help both countries meet energy and climate challenges. Three consortia were established to address the most pressing energy-related research areas: Advanced Coal Technology, Clean Vehicles, and Building Energy Efficiency (BEE). The project discussed in this report was part of the CERC-BEE consortia; its objective was to lower energy use in buildings by developing and evaluating technologies that improve the cost-effectiveness of air barrier systems for building envelopes.

  4. Determination of the Clean Air Delivery Rate (CADR) of Photocatalytic Oxidation (PCO) Purifiers for Indoor Air Pollutants Using a Closed-Loop Reactor. Part II: Experimental Results.

    Science.gov (United States)

    Héquet, Valérie; Batault, Frédéric; Raillard, Cécile; Thévenet, Frédéric; Le Coq, Laurence; Dumont, Éric

    2017-03-06

    The performances of a laboratory PhotoCatalytic Oxidation (PCO) device were determined using a recirculation closed-loop pilot reactor. The closed-loop system was modeled by associating equations related to two ideal reactors: a perfectly mixed reservoir with a volume of VR = 0.42 m³ and a plug flow system corresponding to the PCO device with a volume of VP = 5.6 × 10(-3) m³. The PCO device was composed of a pleated photocatalytic filter (1100 cm²) and two 18-W UVA fluorescent tubes. The Clean Air Delivery Rate (CADR) of the apparatus was measured under different operating conditions. The influence of three operating parameters was investigated: (i) light irradiance I from 0.10 to 2.0 mW·cm(-2); (ii) air velocity v from 0.2 to 1.9 m·s(-1); and (iii) initial toluene concentration C₀ (200, 600, 1000 and 4700 ppbv). The results showed that the conditions needed to apply a first-order decay model to the experimental data (described in Part I) were fulfilled. The CADR values, ranging from 0.35 to 3.95 m³·h(-1), were mainly dependent on the light irradiance intensity. A square root influence of the light irradiance was observed. Although the CADR of the PCO device inserted in the closed-loop reactor did not theoretically depend on the flow rate (see Part I), the experimental results did not enable the confirmation of this prediction. The initial concentration was also a parameter influencing the CADR, as well as the toluene degradation rate. The maximum degradation rate rmax ranged from 342 to 4894 ppbv/h. Finally, this study evidenced that a recirculation closed-loop pilot could be used to develop a reliable standard test method to assess the effectiveness of PCO devices.

  5. 蔬菜清洗中气流强化作用研究%Effects of Vegetable Cleaning Strengthened by Air Fl ow

    Institute of Scientific and Technical Information of China (English)

    李云飞; 张青; 钱丽丽; 李方正

    2001-01-01

    The cleaning mechanisms of vegetable strengthened by air flo w were discussed in the paper. The flow field of cleaning water and the motion s tate of vegetables disturbed by air flow were primarily investigated. The result s s howed that the level of cleaning water was increased approximately 0.03 m due to plenty of gas bubbles near the free surface of water. The cleaning effects of v egetable were strengthened by entrainment of air free-jet and cavitation. Compa red those with non-immersed, the cleaning time for potatoes and greens pre-imm ersed in cool water for 10min, 30 min were also presented.%论述了蔬菜清洗中气流对强化洗净率的作用机理,初步实验研究气流对 洗涤水和蔬菜的扰动状况以及清洗效果。结果表明,在本试验条件下,大量空泡集聚在洗涤 水上部并使清 洗槽液面膨胀0.03 m,射流的卷吸和空泡溃灭强化了对蔬菜的冲刷效果,并给出了马铃薯和 小青菜在未浸泡和分别浸泡10 min、30 min后的洗净时间。

  6. Effect of Water Cleaning on Performance of Air Filtration Medias%水清洗对空气净化材料过滤性能的影响

    Institute of Scientific and Technical Information of China (English)

    刘晓培; 卞思思; 常德强; 毛宁; 柳静献; 孙熙

    2012-01-01

    Air filtration media are designed for disposable, but in some application, it should be used for many times with water cleaning. Through experiments, the performances of polyester fiber layer media, which are cleaned with water for many times, including filtration elfieieney, resistance, dust capacity are studied in the paper. It was indicated by the results that water cleaning has less effect on filtration et/ieieney, resistance and dust capacity of the filter media. Therefore, air filtration media can be used repeatedly by way of water cleaning.%用于空气净化的材料一般为一次性使用,但有的应用场所需要对其进行反复水清洗多次使用。通过实验手段,研究常规涤纶纤维层滤料,在荷尘、清洗、烘干、荷尘等多次反复中其过滤效率、阻力、容尘量的变化情况。实验结果表明,清洗对滤料的过滤效率、阻力和容尘量没有明显的影响,滤料可以通过水清洗的方式反复使用。

  7. Clean air conditioning system design of clean operating departments for the new medical zone of Xiangya Hospital%湘雅医院新医疗区洁净手术部净化空调系统设计

    Institute of Scientific and Technical Information of China (English)

    王小明; 余念贵

    2014-01-01

    简单介绍了湘雅医院新医疗区洁净手术部净化空调系统的设计和修改过程。该工程采用湿度优先控制系统,由新风系统负担手术室的全部湿负荷,解决了洁净手术部与新医疗区共用冷热源可能产生的问题,减少了常规一次回风空调系统中冷热抵消造成的能量浪费,取得了较好的节能效果。%Briefly presents the design and modification process of the clean operating departments.By adopting the humidity priority control system and handling all the moisture load of operating rooms by an outdoor air system,solves the potential problems caused by the clean operating departments and the new medical zone sharing with cold and heat sources,and reduces the energy waste caused by heat and cold offset in conventional primary return air systems,which obtains good energy saving effect.

  8. Clean Power Plan Toolbox

    Science.gov (United States)

    These are resources to help states as they develop state implementation plans under section 111(d) of the Clean Air Act to meet EPA's carbon pollution standards for existing power plants. Supplements www2.epa.gov/carbon-pollution-standards.

  9. Advanced physical coal cleaning to comply with potential air toxic regulations. [Quarterly] technical report, September 1--November 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Honaker, R.Q.; Paul, B.C.; Wang, D. [Southern Illinois Univ., Carbondale, IL (United States). Dept. of Mining Engineering

    1994-12-31

    This research project will investigate the use of advanced fine coal cleaning technologies for cleaning PCB feed as a compliance strategy. Trace elements considered in this project will include mercury, selenium, cadmium, and chlorine. Work in the first quarter has focused on trace element analysis procedures and sample acquisition. Several experts in the field of trace element analysis of coal have been consulted and these procedures are presently being evaluated.

  10. 77 FR 16509 - Proposed Approval of Revision of Five California Clean Air Act Title V Operating Permits Programs

    Science.gov (United States)

    2012-03-21

    ... definition of ``regulated air pollutant'' now includes greenhouse gases if the source has a potential to emit... Pollution Control District (MBUAPCD), San Luis Obispo County Air Pollution Control District (SLOCAPCD), Santa Barbara County Air Pollution Control District (SBCAPCD), South Coast Air Quality...

  11. Plasma Cleaning

    Science.gov (United States)

    Hintze, Paul E.

    2016-01-01

    NASA's Kennedy Space Center has developed two solvent-free precision cleaning techniques: plasma cleaning and supercritical carbon dioxide (SCCO2), that has equal performance, cost parity, and no environmental liability, as compared to existing solvent cleaning methods.

  12. Analysis and evaluation methods for chemical contaminants in clean room air; Kagaku osen no bunseki hyokaho clean room kukichu no kagaku osen busshitsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, T.

    1998-07-31

    As for, chemical contamination in a cleanroom air has taken up as a important problem. As the main source is building materials, after construction the execution of countermeasures is difficult. Out-gas evaluation and selection in building materials, chemical filters for removing specific organic matter and so on, are a large technical theme in the future and analytical techniques corresponding them become necessary. In this paper, analytical methods of airborne molecular contaminants (AMCs) are introduced. Main samples are AMCs in cleanroom atmosphere, on silicon wafer surface and out-gas from raw materials for cleanroom construction materials such as sealant, plastics and so on. Analytical methods consist of quantification of inorganic compounds, organic compounds and identification of abnormal spot with local/surface analysis. Various interesting findings with analytical data are obtained and investigated. 22 refs., 6 figs., 5 tabs.

  13. Study on Cleaning Methods of Central Air Conditioning Water Cystem%中央空调水系统的清洗方法研究

    Institute of Scientific and Technical Information of China (English)

    刘孝刚

    2014-01-01

    为提高换热效率、防止和减少水的腐蚀,中央空调的冷却水系统和冷冻水系统都应定期进行清洗,以除去金属表面上的沉积物和杀灭微生物。对于新建的中央空调,其冷却水和冷冻水系统中的设备在制造加工中和运输储存期间都会发生锈蚀,带入的切削油、防锈油严重影响中央空调水系统的运行,在安装过程中还会下碎屑、油类、泥砂和杂质。因此,对中央空调水系统的清洗方法的研究显得尤为重要。%In order to improve thermal efficiency, prevent and reduce the corrosion of water, the cooling water system and chilled water system of central air conditioning should be regular cleaning, so as to remove sediments on the surface of metals and exterminate microorganisms. In term of the new central air conditioning, the equipments of cooling water system and chilled water system would be easily corroded in the process of manufacturing , storage and transportation, cutting oil, rust-proof oil brought in would seriously affect the operation of central air conditioning water system, during the installation process there will be fallen debris, oil, mud, sand and impurities. Therefore, the study of the central air conditioning water system cleaning methods is particularly important.

  14. Analysis of the Clean Air Act Amendments of 1990: A forecast of the electric utility industry response to Title IV, Acid Deposition Control

    Energy Technology Data Exchange (ETDEWEB)

    Molburg, J.C.; Fox, J.A.; Pandola, G.; Cilek, C.M.

    1991-10-01

    The Clean Air Act Amendments of 1990 incorporate, for the first time, provisions aimed specifically at the control of acid rain. These provisions restrict emissions of sulfur dioxide (SO{sub 2}) and oxides of nitrogen (NO{sub x}) from electric power generating stations. The restrictions on SO{sub 2} take the form of an overall cap on the aggregate emissions from major generating plants, allowing substantial flexibility in the industry`s response to those restrictions. This report discusses one response scenario through the year 2030 that was examined through a simulation of the utility industry based on assumptions consistent with characterizations used in the National Energy Strategy reference case. It also makes projections of emissions that would result from the use of existing and new capacity and of the associated additional costs of meeting demand subject to the emission limitations imposed by the Clean Air Act. Fuel-use effects, including coal-market shifts, consistent with the response scenario are also described. These results, while dependent on specific assumptions for this scenario, provide insight into the general character of the likely utility industry response to Title IV.

  15. Analysis of the Clean Air Act Amendments of 1990: A forecast of the electric utility industry response to Title IV, Acid Deposition Control

    Energy Technology Data Exchange (ETDEWEB)

    Molburg, J.C.; Fox, J.A.; Pandola, G.; Cilek, C.M.

    1991-10-01

    The Clean Air Act Amendments of 1990 incorporate, for the first time, provisions aimed specifically at the control of acid rain. These provisions restrict emissions of sulfur dioxide (SO[sub 2]) and oxides of nitrogen (NO[sub x]) from electric power generating stations. The restrictions on SO[sub 2] take the form of an overall cap on the aggregate emissions from major generating plants, allowing substantial flexibility in the industry's response to those restrictions. This report discusses one response scenario through the year 2030 that was examined through a simulation of the utility industry based on assumptions consistent with characterizations used in the National Energy Strategy reference case. It also makes projections of emissions that would result from the use of existing and new capacity and of the associated additional costs of meeting demand subject to the emission limitations imposed by the Clean Air Act. Fuel-use effects, including coal-market shifts, consistent with the response scenario are also described. These results, while dependent on specific assumptions for this scenario, provide insight into the general character of the likely utility industry response to Title IV.

  16. Advanced physical coal cleaning to comply with potential air toxic regulations. Quarterly report, 1 March 1995--31 May 1995

    Energy Technology Data Exchange (ETDEWEB)

    Honaker, R.Q.; Paul, B.C.; Mohanty, M.K.; Wang, D.

    1995-12-31

    Studies have indicated that the potentially hazardous trace elements found in coal have a strong affinity for coal pyrite. Thus, by maximizing the rejection of pyrite, one can minimize the trace element content of a given coal while also reducing sulfur emissions. The pyrite in most Illinois Basin coals, however, is finely disseminated within the coal matrix. Therefore, to remove the pyrite using physical coal cleaning techniques, the pyrite must be liberated by grinding the coal to ultrafine particle sizes. Fortunately, the coals being fed to pulverized coal boilers (PCB) are already ground to a very fine size, i.e., 70% passing 200 mesh. Therefore, this research project will investigate the use of advanced fine coal cleaning technologies for cleaning PCB feed as a compliance strategy. Work in this quarter has focused on the processing of a run-of-mine coal sample collected from Amax Coal Company`s Delta Coal mine using column flotation and an enhanced gravity separator as separate units and in circuitry arrangements. The {minus}60 mesh run-of-mine sample having an ash content of about 22% was cleaned to 6% while achieving a very high energy recovery of about 87% and a sulfur rejection value of 53% in a single stage column flotation operation. Enhanced gravity treatment is believed to be providing excellent total sulfur rejection values, although with inferior ash rejection for the {minus}400 mesh size fraction. The circuitry arrangement with the Falcon concentrator as the primary cleaner followed by the Packed-Column resulted in an excellent ash rejection performance, which out performed the release analysis. Trace element analyses of the samples collected from these tests will be conducted during the next report period.

  17. Advanced physical coal cleaning to comply with potential air toxic regulations. Quarterly report, 1 December 1994--28 February 1995

    Energy Technology Data Exchange (ETDEWEB)

    Honaker, R.Q.; Paul, B.C.; Wang, D.

    1995-12-31

    Studies have indicated that the potentially hazardous trace elements found in coal have a strong affinity for coal pyrite. Thus, by maximizing the rejection of pyrite, one can minimize the trace element content of a given coal while also reducing sulfur emissions. The pyrite in most Illinois Basin coals, however, is finely disseminated within the coal matrix. Therefore, to remove the pyrite using physical coal cleaning techniques, the pyrite must be liberated by grinding the coal to ultrafine particle sizes. Fortunately, the coals being fed to pulverized coal boilers (PCB) are already ground to a very fine size, i.e., 70% passing 200 mesh. Therefore, this research project will investigate the use of advanced fine coal cleaning technologies for cleaning PCB feed as a compliance strategy. Work in this quarter has focused on the processing of a PCB feed sample collected from Central Illinois Power`s Newton Power Station using column flotation and an enhanced gravity separator as separate units and in a circuitry arrangement. The PCB feed sample having a low ash content of about 12% was further cleaned to 6% while achieving a very high energy recovery of about 90% in a single stage column flotation operation. Enhanced gravity treatment is believed to be providing excellent total sulfur rejection values, although with inferior ash rejection for the {minus}400 mesh size fraction. The circuitry arrangement with the Falcon concentrator as the primary cleaner followed by the Microcel column resulted in an excellent ash rejection performance, which out performed the release analysis. Trace element analyses of the samples collected from these tests will be conducted during the next report period.

  18. 77 FR 15267 - Clean Air Act Full Approval of Title V Operating Permits Program; Southern Ute Indian Tribe

    Science.gov (United States)

    2012-03-15

    ... review of the Tribe's authority to regulate air pollution sources located within the exterior boundaries... jurisdiction to regulate non- Indian-owned air pollution sources located on fee lands within the Reservation... greenhouses gases as part of the Prevention of Significant Deterioration/Title V Greenhouse Gas Tailoring...

  19. Clean data

    CERN Document Server

    Squire, Megan

    2015-01-01

    If you are a data scientist of any level, beginners included, and interested in cleaning up your data, this is the book for you! Experience with Python or PHP is assumed, but no previous knowledge of data cleaning is needed.

  20. 中央空调风系统管道清洗的调查探讨%On exploration for investigation of pipeline cleaning of central air-conditioner wind system

    Institute of Scientific and Technical Information of China (English)

    温嘉

    2012-01-01

    The study illustrates the necessity for the cleaning of the central air-conditioner system,introduces the development status and problems in the cleaning industry of the central pipeline air-conditioner system at home and abroad,and has the perspective for the future of the cleaning industry of the central air-conditioner system in China.%阐述了中央空调风系统清洗的必要性,介绍了国内外中央空调风系统管道清洗行业的发展状况和存在的问题,展望了我国中央空调风系统管道清洗行业发展的大好前景。

  1. Relating health and climate impacts to grid-scale emissions using adjoint sensitivity modeling for the Climate and Clean Air Coalition

    Science.gov (United States)

    Henze, D. K.; Lacey, F.; Seltzer, M.; Vallack, H.; Kuylenstierna, J.; Bowman, K. W.; Anenberg, S.; Sasser, E.; Lee, C. J.; Martin, R.

    2013-12-01

    The Climate and Clean Air Coalition (CCAC) was initiated in 2012 to develop, understand and promote measures to reduce short lived climate forcers such as aerosol, ozone and methane. The Coalition now includes over 30 nations, and as a service to these nations is committed to providing a decision support toolkit that allows member nations to explore the benefits of a range of emissions mitigation measures in terms of the combined impacts on air quality and climate and so help in the development of their National Action Plans. Here we will present recent modeling work to support the development of the CCAC National Action Plans toolkit. Adjoint sensitivity analysis is presented as a means of efficiently relating air quality, climate and crop impacts back to changes in emissions from each species, sector and location at the grid-scale resolution of typical global air quality model applications. The GEOS-Chem adjoint model is used to estimate the damages per ton of emissions of PM2.5 related mortality, the impacts of ozone precursors on crops and ozone-related health effects, and the combined impacts of these species on regional surface temperature changes. We show how the benefits-per-emission vary spatially as a function of the surrounding environment, and how this impacts the overall benefit of sector-specific control strategies. We present initial findings for Bangladesh, as well as Mexico, Ghana and Colombia, some of the first countries to join the CCAC, and discuss general issues related to adjoint-based metrics for quantifying air quality and climate co-benefits.

  2. Criminal provisions of the Clean Air Act Amendments of 1990 and their interface with the United States sentencing guidelines. Master's thesis

    Energy Technology Data Exchange (ETDEWEB)

    Bowen, W.P.

    1991-09-30

    The growing severity of our societal response to environmental misconduct is reflected, in part, by the criminalization of environmental wrongs by both state and Federal governments. Indeed, the recently enacted Clean Air Act Amendments of 1990 continue this trend, giving the Environmental Protection Agency, via the Department of Justice, significant new criminal enforcement tools. The importance attached to law enforcement of environmental laws is a relatively recent phenomenon and took a significant upswing in 1982 when the department of Justice created what is today the Environmental Crimes Section in what is now the Environment and Natural Resources Division, which section has grown steadily and now has over 25 attorneys who prosecute or assist in the prosecution of environmental crimes in the U.S.

  3. 76 FR 21345 - Science Advisory Board Staff Office; Notification of Two Public Teleconferences of the Clean Air...

    Science.gov (United States)

    2011-04-15

    ... plans for Photochemical Assessment Monitoring Stations (PAMS) Network Re-engineering. DATES: Two public... EPA CASAC Web site at http://www.epa.gov/casac . Any inquiry regarding EPA's PAMS Network Re... plans for PAMS Network Re-engineering. EPA's Office of Air and Radiation (OAR) designed the PAMS...

  4. Environmental compliance guide. Guidance manual for Department of Energy compliance with the Clean Air Act: nonattainment areas

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-09-01

    The purpose of this manual is to identify information requirements associated with air quality permit applications in areas for which ambient pollutant levels currently exceed the national ambient air quality standards (nonattainment areas). The manual is to be used by project managers at the US Department of Energy (DOE), in conjunction with the DOE Environmental Compliance Guide, to provide preliminary estimates of information required to obtain air quality permits for DOE projects. An analysis of nonattainment area permitting found that permitting of all sources in such areas is done on the state or local levels; the Environmental Protection Agency does not grant permits in nonattainment areas. As a result, Federal information requirements for permitting in nonattainment areas are somewhat vague. To provide a more realistic picture of nonattainment area permitting, selected state and local regulations were surveyed, and were found to contain more detail on the information required for permit approval. The most potentially demanding information requirements associated with nonattainment area permitting are the determination of Lowest Achievable Emission Rate, the negotiation of external emission offsets, and the consideration of the environmental impacts of project alternatives in ozone and carbon monoxide nonattainment areas. In any state, a few information requirements for nonattainment area permitting are likely to overlap with information requirements of other permitting processes, such as those in the Prevention of Significant Deterioration procedure. These requirements are emissions data and air quality modeling and its associated input data requirements (meteorology, topography, etc.).

  5. 76 FR 36120 - Science Advisory Board Staff Office Notification of a Public Meeting of the Clean Air Scientific...

    Science.gov (United States)

    2011-06-21

    ... on EPA's Review of the National Ambient Air Quality Standards for Lead: Risk and Exposure Assessment... that are important to the design and scope of exposure and risk assessments, as well as other aspects...: Risk and Exposure Assessment Planning Document. DATES: The CASAC Lead Review Panel meeting will be...

  6. Effect of Air Cleaning Technologies in Conjunction With the Use of Rotary Heat Exchangers in Residential Buildings

    DEFF Research Database (Denmark)

    Afshari, Alireza; Bergsøe, Niels Christian; Ekberg, Lars

    2013-01-01

    with rotary air-to-air heat exchangers. For this purpose, a mechanical filter with low pressure drop and a 4 cm thick activated carbon filter were selected for testing in a laboratory environment. The measurements included testing of the filters, separately and combined, in a ductwork to study the efficiency...... of the filters. The removal efficiency of the mechanical filter for ultrafine particles was examined using burning candles as sources for emission of particles. The measurements in the duct showed that the efficiency of the particle filter ranged between approximately 50% and 80% and the pressure loss...... of gases. The measurement results showed that the efficiency of the combined filters ranged between approximately 30% and 80% and the pressure loss was less than approximately 20 Pascal at an airflow rate of 250 m3/h....

  7. Testing the efficacy and the potential effect on indoor air quality of a transparent self-cleaning TiO{sub 2}-coated glass through the degradation of a fluoranthene layer

    Energy Technology Data Exchange (ETDEWEB)

    Romeas, V.; Pichat, P.; Guillard, C.; Chopin, T.; Lehaut, C.

    1999-10-01

    Self-cleaning glass can be obtained by coating glass with a transparent, thin layer of TiO{sub 2} nanoparticles. To test the self-cleaning properties, fluoranthene--the most abundant polycyclic aromatic hydrocarbon in the atmospheric particulate matter--was sprayed over the glass. Under solar-like UV light, not only was fluoranthene removed at a rate of ca. 0.73 nmol/h per cm{sup 2} of glass but also all fluoranthene degradation products were, and thus the coated-glass transparency was recovered, which did not occur with noncoated glass. The fluoranthene percentage converted to volatile carbonyl products released into ambient air was lower with than without TiO{sub 2} coating; i.e., the self-cleaning glass could have a positive influence on indoor air quality. Mechanisms are discussed to account for the main primary products among the 40 fluoranthene photocatalytic degradation intermediate products which the authors identified.

  8. 浅析某血液制品车间的洁净空调设计%Brief Analysis of Design of Cleaning Air-conditioner Used in One Blood Product Workshop

    Institute of Scientific and Technical Information of China (English)

    邓盼盼

    2015-01-01

    Based on the design of cleaning air-conditioner used in one blood product workshop, and combined with the special condition and design requirements, the principles and methods in designing cleaning air-conditioner were introduced in this article. At the same time, the notices in the design of cleaning air-conditioner and the special features in designing cleaning air-conditioner for blood products were analyzed and discussed.%以某血液制品生产车间的洁净空调设计过程为依据,结合该类药品生产的特殊情况及设计要求,介绍了洁净空调系统设计的原则及方法等问题,分析探讨了洁净空调设计时应该注意的事项以及该类药品的洁净空调设计的特殊性。

  9. Emission projections for the U.S. Environmental Protection Agency Section 812 second prospective Clean Air Act cost/benefit analysis.

    Science.gov (United States)

    Wilson, James H; Mullen, Maureen A; Bollman, Andrew D; Thesing, Kirstin B; Salhotra, Manish; Divita, Frank; Neumann, James E; Price, Jason C; DeMocker, James

    2008-05-01

    Section 812 of the Clean Air Act Amendments (CAAA) of 1990 requires the U.S. Environmental Protection Agency (EPA) to perform periodic, comprehensive analyses of the total costs and total benefits of programs implemented pursuant to the CAAA. The first prospective analysis was completed in 1999. The second prospective analysis was initiated during 2005. The first step in the second prospective analysis was the development of base and projection year emission estimates that will be used to generate benefit estimates of CAAA programs. This paper describes the analysis, methods, and results of the recently completed emission projections. There are several unique features of this analysis. One is the use of consistent economic assumptions from the Department of Energy's Annual Energy Outlook 2005 (AEO 2005) projections as the basis for estimating 2010 and 2020 emissions for all sectors. Another is the analysis of the different emissions paths for both with and without CAAA scenarios. Other features of this analysis include being the first EPA analysis that uses the 2002 National Emission Inventory files as the basis for making 48-state emission projections, incorporating control factor files from the Regional Planning Organizations (RPOs) that had completed emission projections at the time the analysis was performed, and modeling the emission benefits of the expected adoption of measures to meet the 8-hr ozone National Ambient Air Quality Standards (NAAQS), the Clean Air Visibility Rule, and the PM2.5 NAAQS. This analysis shows that the 1990 CAAA have produced significant reductions in criteria pollutant emissions since 1990 and that these emission reductions are expected to continue through 2020. CAAA provisions have reduced volatile organic compound (VOC) emissions by approximately 7 million t/yr by 2000, and are estimated to produce associated VOC emission reductions of 16.7 million t by 2020. Total oxides of nitrogen (NO(x)) emission reductions attributable to the

  10. The role of integrated resource planning, environmental externalities, and anticipation of future regulation in compliance planning under the Clean Air Act Amendments of 1990

    Energy Technology Data Exchange (ETDEWEB)

    Bernow, S.; Biewald, B.; Wulfsberg, K. [Tellus Institute, Boston, MA (United States)

    1993-07-01

    Utilities are developing sulfur dioxide (SO{sub 2}) emission compliance plans to meet limitations of the Clean Air Act Amendments of 1990 (CAAA). Compliance plans will have long-term effects on resource selection, fuel choice, and system dispatch. Use of integrated resource planning (IRP) is necessary to ensure compliance plans are consistent with the overall societal goals. In particular, environmental externalities must be integrated with the compliance planning process. The focus of the CAAA is on air pollution reduction, specifically acid gases and toxics, and attainment of National Ambient Air Quality Standards (NAAQS) for criteria pollutants. Title IV specifically focuses on sulfur dioxide with a national allowance trading system, while further regulation of toxics and nitrogen oxides is slated for additional study. Yet, compliance planning based narrowly upon today`s environmental regulations could fail to meet the broad goals of IRP if a larger array of environmental externalities is excluded from the analysis. Compliance planning must consider a broad range of environmental effects from energy production and use to (1) protect society`s long-term stake in environmental quality, and (2) ensure that today`s plans are rich enough to accommodate potential changes in regulation and national environmental goals. The explicit recognition of environmental effects, such as those associated with CO{sub 2} release, will result in prudent compliance plans that take advantage of current opportunities for pollution avoidance and have long-term viability in the face of regulatory change. By including such considerations, the mix of resources acquired and operated (supply and demand, existing and new, conventional and renewable, fuel type and fuel quality, pollution control, and dispatch protocols) will be robust and truly least-cost.

  11. Experimental Study on Efficient Photocatalysis Air Cleaning Device%一种光触媒高效空气净化器的实验研究

    Institute of Scientific and Technical Information of China (English)

    闫其年; 刘志强; 杨景发; 张子生

    2011-01-01

    In order to achieve the purpose of efficient air purification , based on the physical method,the sketch map of cyclotron duct for diversion and syntonic light source structure were designed by using the Photocatalysis of TiO2 and the biology effect of ozone and ultraviolet. The efficient photocatalysis air cleaning cartridge which was used for poultry house has the advantage of advanced air-filtering ability, enduring and stable effect as well as wide range of application. The cartridge's efficiency of removing germ,formaldehyde and ammonia was 90.9%, 63.9% and 86.2% respectively.%为了达到高效净化空气的目的,从物理方法入手,利用二氧化钛光触媒的光催化作用、短波紫外线和臭氧的生物效应原理,通过"多波段谐振光源"和"导流回旋风道"的设计,研制出一款光触媒高效空气净化器,具有净化空气能力强、效果持久稳定、无二次公害和维持费用低、操作简便、适用范围广等优点.细菌的去除效率在90.9%以上,甲醛去除效率为63.9%,氨去除效率为86.2%.

  12. The implement of air pollution detection and clean based on the TP-4 sensor%基于TP-4传感器的空气污染检测及清理的实现

    Institute of Scientific and Technical Information of China (English)

    周凡力; 耿建平

    2012-01-01

    Aiming at indoor air pollution, a kind of effective detection and clean design scheme for cleaning indoor air and improving living environment was proposed. Degree of air pollution indoor was tested by TP-4 sensors, and sending the data to calculate by microcontroller, then the microcontroller controled the air pollution treatment to e-liminate the air pollution according to the results. The microcontroller processing method adopted PID real-time control technology to make the air clean. The technology adopted in this scheme can clean air quickly,suit to family and office environment.%针对室内空气污染,提出了一种有效的检测及清理设计方案,以达到清洁室内空气、保障生活环境的目的.采用TP-4传感器对室内空气污染程度进行检测,将检测采样结果送到单片机进行处理,由单片机根据处理结果控制空气污染处理器来消除空气中的污染.单片机处理方法则采用PID实时控制技术,使空气始终保持在清洁状态下.该方案采用的控制技术能迅速清洁空气,适用于家庭与办公环境下的空气清理.

  13. Demonstration of Air-Power-Assist Engine Technology for Clean Combustion and Direct Energy Recovery in Heavy Duty Application

    Energy Technology Data Exchange (ETDEWEB)

    Hyungsuk Kang; Chun Tai

    2010-05-01

    The first phase of the project consists of four months of applied research, starting from September 1, 2005 and was completed by December 31, 2005. During this time, the project team heavily relied on highly detailed numerical modeling techniques to evaluate the feasibility of the APA technology. Specifically, (i) A GT-Power{sup TM}engine simulation model was constructed to predict engine efficiency at various operating conditions. Efficiency was defined based on the second-law thermodynamic availability. (ii) The engine efficiency map generated by the engine simulation was then fed into a simplified vehicle model, which was constructed in the Matlab/Simulink environment, to predict fuel consumption of a refuse truck on a simple collection cycle. (iii) Design and analysis work supporting the concept of retrofitting an existing Sturman Industries Hydraulic Valve Actuation (HVA) system with the modifications that are required to run the HVA system with Air Power Assist functionality. A Matlab/Simulink model was used to calculate the dynamic response of the HVA system. Computer aided design (CAD) was done in Solidworks for mechanical design and hydraulic layout. At the end of Phase I, 11% fuel economy improvement was predicted. During Phase II, the engine simulation group completed the engine mapping work. The air handling group made substantial progress in identifying suppliers and conducting 3D modelling design. Sturman Industries completed design modification of the HVA system, which was reviewed and accepted by Volvo Powertrain. In Phase II, the possibility of 15% fuel economy improvement was shown with new EGR cooler design by reducing EGR cooler outlet temperature with APA engine technology from Air Handling Group. In addition, Vehicle Simulation with APA technology estimated 4 -21% fuel economy improvement over a wide range of driving cycles. During Phase III, the engine experimental setup was initiated at VPTNA, Hagerstown, MD. Air Handling system and HVA

  14. 电子工业厂房洁净空调系统施工监理的控制要点%On controlling points for construction inspection for cleaning air-conditioner system of electronic industrial workshops

    Institute of Scientific and Technical Information of China (English)

    吕坤

    2015-01-01

    Combining with engineering cases,the paper analyzes the features of cleaning air-conditioner system of electronic industrial workshops, and illustrates the monitoring controlling points for the cleaning air-conditioner system of electronic industrial workshops from the materials and equipment entry,installation of air-conditioner wind system and air-conditioner water system,so as to enhance the cleaning air-conditioner system to achieve the expected effect.%结合工程案例,分析了电子工业洁净空调系统的特点,并从材料和设备进场、空调风系统安装、空调水系统安装三个方面出发,阐述了电子工业厂房洁净空调系统施工的监理控制要点,促使洁净空调系统达到预期的效果。

  15. Clean Cities ozone air quality attainment and maintenance strategies that employ alternative fuel vehicles, with special emphasis on natural gas and propane

    Energy Technology Data Exchange (ETDEWEB)

    Santini, D.J.; Saricks, C.L.

    1998-08-04

    Air quality administrators across the nation are coming under greater pressure to find new strategies for further reducing automotive generated non-methane hydrocarbon (NMHC) and nitrogen oxide (NOx) emissions. The US Environmental Protection Agency (EPA) has established stringent emission reduction requirements for ozone non-attainment areas that have driven the vehicle industry to engineer vehicles meeting dramatically tightened standards. This paper describes an interim method for including alternative-fueled vehicles (AFVs) in the mix of strategies to achieve local and regional improvements in ozone air quality. This method could be used until EPA can develop the Mobile series of emissions estimation models to include AFVs and until such time that detailed work on AFV emissions totals by air quality planners and emissions inventory builders is warranted. The paper first describes the challenges confronting almost every effort to include AFVs in targeted emissions reduction programs, but points out that within these challenges resides an opportunity. Next, it discusses some basic relationships in the formation of ambient ozone from precursor emissions. It then describes several of the salient provisions of EPA`s new voluntary emissions initiative, which is called the Voluntary Mobile Source Emissions Reduction Program (VMEP). Recent emissions test data comparing gaseous-fuel light-duty AFVs with their gasoline-fueled counterparts is examined to estimate percent emissions reductions achievable with CNG and LPG vehicles. Examples of calculated MOBILE5b emission rates that would be used for summer ozone season planning purposes by an individual Air Quality Control Region (AQCR) are provided. A method is suggested for employing these data to compute appropriate voluntary emission reduction credits where such (lighter) AFVs would be acquired. It also points out, but does not quantify, the substantial reduction credits potentially achievable by substituting gaseous

  16. EIA's role in the analysis of the Clean Air Act Amendments of 1990 and the development of the National Allowance Database

    Energy Technology Data Exchange (ETDEWEB)

    Beamon, J.A.; Linders, M.J. (Energy Information Administration, Washington, DC (United States))

    1993-01-01

    Throughout 1990 the Energy Information Administration (EIA) provided continuous data and analytic support to Congress during its deliberations on Title IV of the Clean Air Act Amendments of 1990 (CAA). Congress requested the Energy Information Administration (EIA) to review and analyze the sections that would affect electric utilities, specifically those relating to acid deposition (Title IV). By providing knowledgeable and impartial analysis, EIA clarified the likely effects of the various legislative proposals and helped Congress finalize the amendments. Even though the CAA is now law, EIA's efforts have not ended. During the analysis of the various proposals, EIA and EPA created a National Allowance Database (NAD). Now, under an agreement with the Environmental Protection Agency (EPA), a new version of the NAD is being developed to facilitate the implementation of the acid deposition provisions of the CAA. This article describes the analyses undertaken, points out where EIA's efforts led to improved understanding of the likely impacts of the CAA, and outlines EIA's continued efforts to assist EPA in the implementation of the amendments. 6 tabs.

  17. On the way towards clean air. Plan to improve the air quality of the Zuidvleugel area, Netherlands; Op weg naar schone lucht. Plan van Aanpak Luchtkwaliteit Zuidvleugel

    Energy Technology Data Exchange (ETDEWEB)

    Janse, P.; Klooster, J.P.G.N.

    2006-01-15

    An overview is given of measures to be taken to improve the air quality in the area Zuidvleugel of western urban area in the Netherlands ('Randstad'), including an estimation of costs to implement and realize the measures in a short term. [Dutch] In de Zuidvleugel van de Randstad is de lucht vervuild. De luchtkwaliteit voldoet niet aan de Europese normen voor de stoffen stikstofdioxide (NO2) en fijn stof (PM10). Verbetering van de luchtkwaliteit staat daarom hoog op de agenda van de rijksoverheid en bestuurders in de Zuidvleugel. In opdracht van de Provincie Zuid-Holland heeft CE een inventarisatie, beoordeling en kostenraming gemaakt van maatregelen om de luchtkwaliteit te verbeteren. Vervolgens heeft CE een voorstel geformuleerd voor een effectief maatregelpakket, dat in beginsel op korte termijn kan worden uitgevoerd. Bij het samenstellen van het maatregelpakket is rekening gehouden met: effect op luchtkwaliteit (in termen van concentraties); kosteneffectiviteit; uitvoerbaarheid (maatschappelijk draagvlak/honing en azijn); termijn waarop gestart kan worden met uitvoering. In het rapport zijn de hoofdlijnen opgenomen van het pakket van maatregelen in de Zuidvleugel en een indicatie van de kosten in de periode 2006-2010.

  18. Fate and aqueous transport of mercury in light of the Clean Air Mercury Rule for coal-fired electric power plants

    Science.gov (United States)

    Arzuman, Anry

    Mercury is a hazardous air pollutant emitted to the atmosphere in large amounts. Mercury emissions from electric power generation sources were estimated to be 48 metric tons/year, constituting the single largest anthropogenic source of mercury in the U.S. Settled mercury species are highly toxic contaminants of the environment. The newly issued Federal Clean Air Mercury Rule requires that the electric power plants firing coal meet the new Maximum Achievable Mercury Control Technology limit by 2018. This signifies that all of the air-phase mercury will be concentrated in solid phase which, based on the current state of the Air Pollution Control Technology, will be fly ash. Fly ash is utilized by different industries including construction industry in concrete, its products, road bases, structural fills, monifills, for solidification, stabilization, etc. Since the increase in coal combustion in the U.S. (1.6 percent/year) is much higher than the fly ash demand, large amounts of fly ash containing mercury and other trace elements are expected to accumulate in the next decades. The amount of mercury transferred from one phase to another is not a linear function of coal combustion or ash production, depends on the future states of technology, and is unknown. The amount of aqueous mercury as a function of the future removal, mercury speciation, and coal and aquifer characteristics is also unknown. This paper makes a first attempt to relate mercury concentrations in coal, flue gas, fly ash, and fly ash leachate using a single algorithm. Mercury concentrations in all phases were examined and phase transformation algorithms were derived in a form suitable for probabilistic analyses. Such important parameters used in the transformation algorithms as Soil Cation Exchange Capacity for mercury, soil mercury selectivity sequence, mercury activity coefficient, mercury retardation factor, mercury species soil adsorption ratio, and mercury Freundlich soil adsorption isotherm

  19. Evaluation of air cleanness degree of the urban environment based on negative air ion concentration%基于空气负离子浓度的城市环境空气清洁度评价

    Institute of Scientific and Technical Information of China (English)

    王薇; 余庄; 冀凤全

    2013-01-01

    .Based on the measurement and research of indoor and outdoor of urban environments, air quality was assessed using ion polarity ratio and air ion assessment index (CI). The results show that air cleanness degree increases gradually from urban indoor environment to urban residential environment to country and natural environment. In urban residential environment, the air quality of low high-density residential environment is the best, the NAI concentration reaches to 289 N/cm3 at average value, and its air quality reaches to 1.7 for the cleanest; but high-level residential environment is the worst, the air quality of low high-density residential environment is the best, the NAI concentration reaches to 139 N/cm3 at average value, and its air quality reaches to 0.08 for threshold, maybe heavy pollution. In urban indoor environments, the air quality with natural ventilation and fresh air into the room is the best, and placed the negative ion generator has improved indoor air quality significantly. So the article suggests taking effective measures to increase the distribution of NAI concentration in urban planning and construction in order to improve the urban ecological environment to create a comfortable air environment, and taking the negative air ion concentration as a monitoring and evaluation indicators of the indoor environment, so as to provide a scientific basis and design concept for urban planning and construction, urban forestry planning, energy planning and environmental protection in the future.

  20. Energy Saving Measures of Clean Air Conditioning System in Solid Dosage Forms Workshop of Pharmaceutical Companies%浅谈药厂固体制剂车间净化空调系统的节能措施

    Institute of Scientific and Technical Information of China (English)

    张帆

    2012-01-01

    According to large energy consumption of clean air-conditioning system in solid dosage forms workshop of pharmaceutical companies, combining with the project cases, this paper suggests three energy saving measures.%针对药厂固体制剂车间净化空调系统能耗大的问题,结合具体的工程案例,有针对性地提出了几种有效的节能措施。

  1. 楼宇自控系统在制药企业洁净空调中的应用%Building Automation System in the Pharmaceutical Business Clean Air-conditioning

    Institute of Scientific and Technical Information of China (English)

    张朝刚

    2013-01-01

      This paper described the clean air-conditioning system engineering of a pharmaceutical company, elaborated the structure, function and implementation way of its air-conditioning control system, and pointed out the importance of understanding the working principle and process of air-conditioning to the electrical system designers in air-conditioning automatic control design.%  介绍了某制药企业洁净空调系统工程,详细阐述了其空调控制系统的结构、功能和实现方式。并指出在空调自动控制设计中,了解具体工程的空调工作原理及工艺流程对电气系统设计工程师的重要性。

  2. Gas-Liquid Supersonic Cleaning and Cleaning Verification Spray System

    Science.gov (United States)

    Parrish, Lewis M.

    2009-01-01

    NASA Kennedy Space Center (KSC) recently entered into a nonexclusive license agreement with Applied Cryogenic Solutions (ACS), Inc. (Galveston, TX) to commercialize its Gas-Liquid Supersonic Cleaning and Cleaning Verification Spray System technology. This technology, developed by KSC, is a critical component of processes being developed and commercialized by ACS to replace current mechanical and chemical cleaning and descaling methods used by numerous industries. Pilot trials on heat exchanger tubing components have shown that the ACS technology provides for: Superior cleaning in a much shorter period of time. Lower energy and labor requirements for cleaning and de-scaling uper.ninih. Significant reductions in waste volumes by not using water, acidic or basic solutions, organic solvents, or nonvolatile solid abrasives as components in the cleaning process. Improved energy efficiency in post-cleaning heat exchanger operations. The ACS process consists of a spray head containing supersonic converging/diverging nozzles, a source of liquid gas; a novel, proprietary pumping system that permits pumping liquid nitrogen, liquid air, or supercritical carbon dioxide to pressures in the range of 20,000 to 60,000 psi; and various hoses, fittings, valves, and gauges. The size and number of nozzles can be varied so the system can be built in configurations ranging from small hand-held spray heads to large multinozzle cleaners. The system also can be used to verify if a part has been adequately cleaned.

  3. Physical and Radiative Properties of Aerosol Particles across the Caribbean Basin: A Comparison between Clean and Perturbed African Dust and Volcanic Ash Air Masses

    Science.gov (United States)

    Rivera, H.; Ogren, J. A.; Sheridan, P. J.; Mayol-Bracero, O.

    2009-12-01

    Aerosol’s optical and physical properties were measured during year 2007 at Cape San Juan, a ground-based station located at the northeastern tip of Puerto Rico. The three cases investigated were classified according to the origin of the air masses: clean (C), African dust (AD), and volcanic ash (VA). The instrumentation used included a sunphotometer to determine volume size distributions and aerosol optical thickness (AOT), a 3-wavelength nephelometer to determine the scattering coefficient (σsp), and a 3-wavelength particle/soot absorption photometer (PSAP) to measure the absorption coefficient (σap). The average volume size distributions were trimodal for the C (peaks at 0.14, 0.99 and 4.25 µm radius) and AD (peaks at 0.11, 1.30 and 2.00 µm radius) cases and bimodal for the VA (peaks at 0.19 and 2.75 µm radius) case. Fine and coarse modes maxima for AD occurred at radii smaller than for VA, confirming the different origins of those particles. The average values for the total σsp were higher for AD (82.9 Mm-1) and VA (33.7 Mm-1) compared to C (16.6 Mm-1). The same happened for the AOT maximum values at 500 nm with 0.92, 0.30, and 0.06 for AD, VA, and C, respectively. The observed increase in the values of the Angstrom exponent (å) is indicative of a decrease in the size of the particles associated to VA (å= 0.27) and AD (å =0.89) when compared to C (å =0.24). The volume size distributions and thus the mass were dominated by the coarse mode (> 1.0 µm) especially for the AD case. Results have shown that AD as well as VA has a significant impact on the physical and radiative properties across Puerto Rico and the Caribbean. Additional results on the AOT wavelength dependence and on the annual variability of the properties under study will be presented.

  4. Clean catch urine sample

    Science.gov (United States)

    ... specimen; Urine collection - clean catch; UTI - clean catch; Urinary tract infection - clean catch; Cystitis - clean catch ... LE, Norrby SR. Approach to the patient with urinary tract infection. In: Goldman L, Schafer AI, eds. Goldman-Cecil ...

  5. Rice- and butterfly-wing effect inspired self-cleaning and low drag micro/nanopatterned surfaces in water, oil, and air flow.

    Science.gov (United States)

    Bixler, Gregory D; Bhushan, Bharat

    2014-01-01

    In search of new solutions to complex challenges, researchers are turning to living nature for inspiration. For example, special surface characteristics of rice leaves and butterfly wings combine the shark skin (anisotropic flow leading to low drag) and lotus leaf (superhydrophobic and self-cleaning) effects, producing the so-called rice and butterfly wing effect. In this paper, we study four microstructured surfaces inspired by rice leaves and fabricated with photolithography techniques. We also present a method of creating such surfaces using a hot embossing procedure for scaled-up manufacturing. Fluid drag, self-cleaning, contact angle, and contact angle hysteresis data are presented to understand the role of sample geometrical dimensions. Conceptual modeling provides design guidance when developing novel low drag, self-cleaning, and potentially antifouling surfaces for medical, marine, and industrial applications.

  6. Parameter optimization and experiment on air-screen cleaning device of rapeseed combine harvester%风筛选式油菜联合收割机清选机构参数优化与试验

    Institute of Scientific and Technical Information of China (English)

    张敏; 金诚谦; 梁苏宁; 汤庆; 吴崇友

    2015-01-01

    为分析油菜田间实际收获作业状态时风筛选式油菜联合收割机清选机构参数对清选损失率和籽粒含杂率的影响,基于双滚筒风筛选式可移动田间联合收获试验平台,对振动筛振幅、曲柄转速、风机转速和风机倾角4个参数进行了Plackett-Burman 试验和响应面回归试验,试验分析表明振动筛振幅和曲柄转速是影响清选损失率的主要因素,风机转速是影响籽粒含杂率的主要因素。采用响应面试验方法分析了单因素和双因素对清选效果的影响,建立了清选损失率和籽粒含杂率的回归数学模型并优化求解了一组最优参数组合,以一组接近最优参数组合:振动筛振幅35 mm,曲柄转速392 r/min,风机转速1750 r/min,风机倾角29°进行了试验验证,清选损失率和籽粒含杂率分别为0.90%和0.45%。理论求解的清选损失率和籽粒含杂率分别为0.38%和0.48%,与试验值的绝对误差分别为0.52%和−0.03%,籽粒含杂率误差较小,清选损失率误差较大。与该清选机构常用工作参数时的清选损失率和籽粒含杂率对比,清选损失率降低了61%,籽粒含杂率降低了58%。该研究结果和优化方法可为风筛选式油菜联合收割机清选机构的参数选择和优化提供参考。%China is one of the major rapeseed production countries in the world, but the harvesting mechanization is still backward, and high mechanical harvest loss is a key inhibiting factor for rapeseed production.In order to reduce the harvest loss ratio, the effects of the parameters of air-screen cleaning device of rapeseed combine harvester on cleaning loss ratio and percentage of impurities in grain under the actual field harvest operating condition are needed to understand. In this paper, a Plackett-Burman test and a response surface test were designed to study the 4 parameters: vibration screen amplitude, crank revolving speed, fan revolving speed

  7. Coal can be a Clean Fuel

    Science.gov (United States)

    Environmental Science and Technology, 1975

    1975-01-01

    Redevelopment and expansion of United States coal resources are economic necessities. Environmentalists' objections to the less expensive, available United States coal, that introduces large amounts of SOx and particulates into the air, may be overcome with the options of coal cleaning, tall stacks, material recovery and stack cleaning. (BT)

  8. 电动双位定风量阀在洁净手术部空调系统中的应用%The Application of Electrical Dual-position Consistent Air Valve in Air-Conditioning System of Clean Operation Department

    Institute of Scientific and Technical Information of China (English)

    窦用佳; 刘亮

    2012-01-01

    The stability and energy-saving of dual-position consistent air valve was explained,in terms of consistent air volume(air change rate) to cleanroom and consistent make-up air volume(pressure cascade of clean zone) by using the valve.%从恒定洁净室风量(换气次数)及恒定新风量(洁净区的压力梯度)的角度,利用电动双位定风量阀,阐述电动双位定风量阀在洁净空调系统上所具有的稳定性及节能性。

  9. Supersonic Gas-Liquid Cleaning System

    Science.gov (United States)

    Kinney, Frank

    1996-01-01

    The Supersonic Gas-Liquid Cleaning System Research Project consisted mainly of a feasibility study, including theoretical and engineering analysis, of a proof-of-concept prototype of this particular cleaning system developed by NASA-KSC. The cleaning system utilizes gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the device to be cleaned. The cleaning fluid being accelerated to these high velocities may consist of any solvent or liquid, including water. Compressed air or any inert gas is used to provide the conveying medium for the liquid, as well as substantially reduce the total amount of liquid needed to perform adequate surface cleaning and cleanliness verification. This type of aqueous cleaning system is considered to be an excellent way of conducting cleaning and cleanliness verification operations as replacements for the use of CFC 113 which must be discontinued by 1995. To utilize this particular cleaning system in various cleaning applications for both the Space Program and the commercial market, it is essential that the cleaning system, especially the supersonic nozzle, be characterized for such applications. This characterization consisted of performing theoretical and engineering analysis, identifying desirable modifications/extensions to the basic concept, evaluating effects of variations in operating parameters, and optimizing hardware design for specific applications.

  10. 77 FR 12524 - Approval and Promulgation of Air Quality Implementation Plans; Indiana; Lead Ambient Air Quality...

    Science.gov (United States)

    2012-03-01

    ... Ambient Air Quality Standards AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule...) under the Clean Air Act (CAA). This submittal incorporates the National Ambient Air Quality...

  11. We Pollute the Air

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    1.Clean air is important to good health.If the aircontains impurities,they may be absorbed by ourbodies and make us ill.We need clean air,butunfortunately,air pollution is generally present,especially in cities. 2.Our cities have many factories,which we need tomake food products,clothing and many other things.

  12. Saltstone Clean Cap Formulation

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C

    2005-04-22

    Clean Cap mix generates more bleed water than the reference Saltstone formulation because the specific gravity of water, the carrier fluid, is less than that of the carrier fluid in Saltstone, 1 versus 1.1 to 1.2, respectively. In addition, the development of slurry structure as a result of hydration reactions is slightly slower than in the salt solution slurry. In other words, the Clean Cap mix has a slightly longer gel time. The lower density of the carrier fluid and the slower development of slurry structure, enable more settling to occur (more standing water) in the Clean Cap slurry. Consequently, for the same rheological properties, the Clean Cap slurry will have more bleed water. In an attempt to reduce the bleed water, the water to premix ratio was lowered and dispersants (high range water reducers) were added. Below water to premix ratios of 0.35, little bleed water and settling was observed. However, a low water to premix Clean Cap mix is not recommended because processing has not been demonstrated in the Saltstone facility. The lowest water to premix ratio processed in Z-Area was 0.478 in the last attempt to produce a clean cap. Although this option may provide significant advantages (less bleed water and potentially better flow) process testing in the Saltstone Facility or in a pilot scale facility in conjunction with laboratory testing will be required to demonstrate mixing, pumping and flow properties. Other additives were tested to minimize bleed water. These additives were found to be unsatisfactory in one or more ways and therefore, were not recommended at this time. An air entraining agent and a thickener had some benefit in reducing bleed water but were found too difficult to implement as an additive in the Saltstone facility. Surfactants (air entrainers) added to the mixing water in the hold tank could generate foam as the result of agitation to mix the tank, and the thickener increased the apparent viscosity and yield stress.

  13. 医院洁净手术部空气洁净度监测的效果评价%The evaluation of the cleanliness air monitoring in the hospital clean operating room

    Institute of Scientific and Technical Information of China (English)

    尉永红

    2013-01-01

    Objective Evaluate the monitoring effects of the air cleanliness at operating room of the hospital. Methods The standars and testing methods in the"Hospital Disinfecting Sanitation Standard"(GB15982-1995)have been adopted. Results After strict ,effective and scientific managements made use of the clean operating room of lamina flows, and the successive air monitor by two years, the quantum of existing in the air to meet the Environment Standard Type I. Conclusion Air quality in operating room will be kept in a relatively high standard by applying monitoring system of the air cleanliness at the hospital.%  目的评价医院洁净手术部空气洁净度监测效果。方法依据国家标准《医院洁净手术部建筑技术规范》(GB50333--2002)中规定的标准及检测方法,对我院5个洁净手术间进行每月1次的生物监测。结果洁净手术部实施严格、有效、科学的管理后,通过2年跟踪监测,其空气细菌含量均达到了Ⅰ类环境标准。结论洁净手术部空气洁净度的监测,为我院手术部空气质量的提高提供了有力保障。

  14. Study and Evaluation of Liquid Air Energy Storage Technology For a Clean and Secure Energy Future Challenges and opportunities for Alberta wind energy industry

    Directory of Open Access Journals (Sweden)

    Hadi H. Alyami

    2015-08-01

    Full Text Available Global energy demand is steadily increasing each year. Many jurisdictions are seeking to incorporate sustainable and renewable energy sources to help meeting the demand and doing so in a responsible method to the environment and the next generation. In a wide-context, renewable energy sources are promising, yet cannot be controlled in such a way that is responsive to energy demand fluctuation. Liquid Air Energy Storage (LAES technology seeks to bridge the gap that exists between energy supply and demand in an effort to mitigate the current demand deficiency. The volume ratio of air to liquid air is nearly 700:1. Liquid air is a dense energy carrier that is by converting renewable energy at off-peak periods into liquid air the energy can be stored until a peak-demand period when energy producers are maximising output to meet the demand. The energy is then retrieved from the liquid air through rapid expansion as it re-gasifies through a gas turbine and converted into electricity. A commercial scale pilot plant in Slough, UK illustrates the application of this technology empirically. The application of this technology in Canada might have challenges as public policy respective jurisdictions play a role. A case of point of applications where LAES can be integrated is the renewable energy market; particularly the wind power in Alberta. This paper’s analysis embraces wind power industry in Alberta from the perspective of both the electric system operator and the power generation plant. As such, it serves as an alleviating proposal of the current wind energy issues in Alberta – including the uncertainty of forecasting system. The analysis assumed energy storage technologies as a viable stand-alone mitigation with no consideration of the current technological and operational advancements in power systems such HVDC grids, distributed generation concepts and among others.

  15. Experiment research on multi factors of air-and-screen cleaning device of vertical axial flow%纵轴流风筛式清选装置多因素试验研究

    Institute of Scientific and Technical Information of China (English)

    张义峰; 衣淑娟

    2012-01-01

    In order to improve the cleaning performance of cleaning device of the vertical axial flow of rice combine,the orthogonal rotation experimental researches based on the air-and-screen cleaning device test-bed of longitudinal axial flow designed by ourself is studied.Then the effect of three parameters such as crank rotational speed,centrifugal fan rotational speed and centrifugal fan rake angle on power consumption,dirt percentage and percentage loss is analyzed.With the regression equation of performance index by adopting primary function method and MATLAB optimization and solution are conducted to obtain a optimization parameter after comprehensive assessing as follows: crank rotational speed is 235r/min, centrifugal fan rotational speed is 764r/min and centrifugal fan rake angle is 28°, which is verified through experiment ,the performance index is satisfied.The study can provide referential experience for the design, manufacturing and operating of the screen cleaning device.%为了改善纵轴流水稻收获机清选装置的清选性能,在自行研制了纵轴流风筛式清选装置试验台的基础上进行正交旋转试验研究,分析了清选装置的曲柄转速、离心风机转速、离心风机倾角三个参数对功耗、含杂率、损失率的影响.利用各性能指标的回归方程,采用主目标函数法,用MATLAB进行优化求解,综合评定后得到优化参数为:曲柄转速为235r/min,离心风机转速为764r/min,风机倾角为28°,通过验证试验后,所得到的性能指标均满足要求.通过研究,可为清选装置的设计、制造和使用提供可借鉴的依据.

  16. Air Quality Facilities

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — Facilities with operating permits for Title V of the Federal Clean Air Act, as well as facilities required to submit an air emissions inventory, and other facilities...

  17. pH Control in Fog and Rain in East Asia: Temporal Advection of Clean Air Masses to Mt. Bamboo, Taiwan

    Directory of Open Access Journals (Sweden)

    Otto Klemm

    2015-11-01

    Full Text Available Fog and rain was collected during an 18-day period in January 2011 at Mt. Bamboo, northern Taiwan. Almost 300 hourly fog samples and 16 daily rain samples were taken. One single fog sample (pH 3.17 was influenced by local volcanic activity, otherwise the pH ranged from 3.23 to 6.41 in fog and from 3.59 to 6.31 in rain. All the respective air masses arrived from the northeast, but exhibited two distinct groups: Group_1 had high concentrations of all ions (median interquartile range of total ion concentrations 3200–6200 µeq.·L−1 and low pHs (median 3.52, the respective air masses had travelled over densely populated and industrialized regions of mainland China. Group_2 was from air masses with long travel times over the ocean and relatively low total ion concentrations (80–570 µeq.·L−1 and higher pHs (median 4.80. The cleanest samples are among the cleanest reported in the literature of worldwide fog and rain. In both groups, the pH was governed by the balance of sulfate, nitrate, ammonium, and, in some cases, calcium. The variability of these ions was higher than the variability of 10−pH, which shows that the pH is a rather robust parameter in contrast to its drivers such as non-sea-salt sulfate.

  18. Household Air Pollution Intervention Implications: Findings from Qualitative Studies and a Field Trial of Clean Cookstoves in Two Rural Villages in India

    Science.gov (United States)

    Alam, Ashraful; Tawale, Nanda; Patel, Archana; Dibley, Michael J.; Jadhao, Sunil; Raynes-Greenow, Camille

    2016-01-01

    Exposure to household air pollution is estimated to be the 3rd largest contributor to the global burden of disease and the largest contributor in South Asia. Unacceptability of improved cook stoves by the intended user has been identified as a crucial factor hindering uptake and sustained use. We conducted a qualitative study to understand the socio-cultural factors that influence acceptance of improved cookstoves and conducted a systematic field trial in two rural villages in Maharashtra, India. The qualitative study used semi-structured in-depth interviews and focus group discussions. We included women primarily responsible for household cooking, their husbands, senior women in their households, and community health workers. We also conducted kitchen observations. The results indicated low awareness and knowledge of the health risks associated with traditional cookstove use although high prevalence of household air pollution (HAP) exposure symptoms among all groups. Women were resigned to using traditional cookstoves although they did not like them. The field trial findings were dominated by responses concerned with convenience and health advantages. We identify important issues to be considered when introducing an improved cookstove programme that will increase acceptability and potentially sustained used of improved cookstoves. PMID:27618083

  19. Household Air Pollution Intervention Implications: Findings from Qualitative Studies and a Field Trial of Clean Cookstoves in Two Rural Villages in India

    Directory of Open Access Journals (Sweden)

    Ashraful Alam

    2016-09-01

    Full Text Available Exposure to household air pollution is estimated to be the 3rd largest contributor to the global burden of disease and the largest contributor in South Asia. Unacceptability of improved cook stoves by the intended user has been identified as a crucial factor hindering uptake and sustained use. We conducted a qualitative study to understand the socio-cultural factors that influence acceptance of improved cookstoves and conducted a systematic field trial in two rural villages in Maharashtra, India. The qualitative study used semi-structured in-depth interviews and focus group discussions. We included women primarily responsible for household cooking, their husbands, senior women in their households, and community health workers. We also conducted kitchen observations. The results indicated low awareness and knowledge of the health risks associated with traditional cookstove use although high prevalence of household air pollution (HAP exposure symptoms among all groups. Women were resigned to using traditional cookstoves although they did not like them. The field trial findings were dominated by responses concerned with convenience and health advantages. We identify important issues to be considered when introducing an improved cookstove programme that will increase acceptability and potentially sustained used of improved cookstoves.

  20. Household Air Pollution Intervention Implications: Findings from Qualitative Studies and a Field Trial of Clean Cookstoves in Two Rural Villages in India.

    Science.gov (United States)

    Alam, Ashraful; Tawale, Nanda; Patel, Archana; Dibley, Michael J; Jadhao, Sunil; Raynes-Greenow, Camille

    2016-09-09

    Exposure to household air pollution is estimated to be the 3rd largest contributor to the global burden of disease and the largest contributor in South Asia. Unacceptability of improved cook stoves by the intended user has been identified as a crucial factor hindering uptake and sustained use. We conducted a qualitative study to understand the socio-cultural factors that influence acceptance of improved cookstoves and conducted a systematic field trial in two rural villages in Maharashtra, India. The qualitative study used semi-structured in-depth interviews and focus group discussions. We included women primarily responsible for household cooking, their husbands, senior women in their households, and community health workers. We also conducted kitchen observations. The results indicated low awareness and knowledge of the health risks associated with traditional cookstove use although high prevalence of household air pollution (HAP) exposure symptoms among all groups. Women were resigned to using traditional cookstoves although they did not like them. The field trial findings were dominated by responses concerned with convenience and health advantages. We identify important issues to be considered when introducing an improved cookstove programme that will increase acceptability and potentially sustained used of improved cookstoves.

  1. Understanding in-situ ozone production in the summertime through radical observations and modelling studies during the Clean air for London project

    Science.gov (United States)

    Whalley, Lisa; Stone, Daniel; Sharp, Thomas; Garraway, Shani; Bannan, Thomas; Percival, Carl; Hopkins, James; Holmes, Rachel; Hamilton, Jacqui; Lee, James; Laufs, Sebastian; Kleffmann, Jörg; Heard, Dwayne

    2014-05-01

    With greater than 50 % of the global population residing in urban conurbations, poor urban air quality has a demonstrable effect on human health. OH and HO2 radicals, (collectively termed HOx) together with RO2 radicals, mediate virtually all of the oxidative chemistry in the atmosphere, being responsible for the transformation of primary emissions into secondary pollutants such as NO2, O3 and particulates. Here we present measurements of OH, HO2, partially speciated RO2 (distinguishing smaller alkane related RO2 from larger alkane/alkene/aromatic related RO2), ClNO2 and OH reactivity measurements taken during the ClearfLo campaign in central London in the summer of 2012. Comparison with calculations from a detailed box model utilising the Master Chemical Mechanism v3.2 tested our ability to reproduce radical levels, and enabled detailed radical budgets to be determined, highlighting for example the important role of the photolysis of nitrous acid (HONO) and carbonyl species as radical sources. Speciation of RO2 enabled the break-down of ozone production from different classes of VOCs to be calculated directly and compared with model calculations. Summertime observations of radicals have helped to identify that increases in photolytic sources of radicals on warm, sunny days can significantly increase local ozone concentrations leading to exceedances of EU air quality recommendations of 60 ppbV. The photolytic breakdown of ClNO2 to Cl atoms can more than double radical concentrations in the early morning; although the integrated increase in radical concentrations over a 24 hr period in model runs when ClNO2 photolysis is included is more modest. On average we calculate just under a 1 ppb increase in ozone due to the presence of ClNO2 in London air. OH reactivity was found to be greatest during morning and evening rush hours. Good agreement between the modelled OH reactivity and observations could be achieved when reactivity associated with model generated photo

  2. ASRM process development in aqueous cleaning

    Science.gov (United States)

    Swisher, Bill

    1992-12-01

    Viewgraphs are included on process development in aqueous cleaning which is taking place at the Aerojet Advanced Solid Rocket Motor (ASRM) Division under a NASA Marshall Space and Flight Center contract for design, development, test, and evaluation of the ASRM including new production facilities. The ASRM will utilize aqueous cleaning in several manufacturing process steps to clean case segments, nozzle metal components, and igniter closures. ASRM manufacturing process development is underway, including agent selection, agent characterization, subscale process optimization, bonding verification, and scale-up validation. Process parameters are currently being tested for optimization utilizing a Taguci Matrix, including agent concentration, cleaning solution temperature, agitation and immersion time, rinse water amount and temperature, and use/non-use of drying air. Based on results of process development testing to date, several observations are offered: aqueous cleaning appears effective for steels and SermeTel-coated metals in ASRM processing; aqueous cleaning agents may stain and/or attack bare aluminum metals to various extents; aqueous cleaning appears unsuitable for thermal sprayed aluminum-coated steel; aqueous cleaning appears to adequately remove a wide range of contaminants from flat metal surfaces, but supplementary assistance may be needed to remove clumps of tenacious contaminants embedded in holes, etc.; and hot rinse water appears to be beneficial to aid in drying of bare steel and retarding oxidation rate.

  3. Wagging ETOM's Long Tail: MOOCs, Hangouts on Air, and Formal and Informal Undergraduate Experiences with Climate Change Science and Clean Energy Solutions

    Science.gov (United States)

    Haines-Stiles, G.; Alley, R. B.; Akuginow, E.; McNeal, K.; Blockstein, D.

    2014-12-01

    Climate change can reasonably be described as a "wicked problem" meaning that it is complex, difficult and multi-faceted, although critical to equitable development and the sustainability of human civilization. But while the Wikipedia definition says such problems are "impossible" to solve, not even to try will lead to certain failure. "Earth: The Operators' Manual" (ETOM) was an NSF-funded informal science education project with 3 hour-long TV programs appearing on PBS in 2011 and 2012, along with live presentations by series host, Penn State's Richard Alley, and others at 5 major science centers. Uniquely among climate change programming, ETOM gave equal time to identifying solutions along with climate science, and made all its materials freely available via YouTube. Formal and informal science educators can register to download HD videos for classroom and outreach use, and signups have ranged from middle schools to 4-year colleges. Building on the success of the series and Alley's companion tradebook of the same name, Penn State working with Coursera invited Alley to develop a MOOC entitled "Energy, The Environment and Our Future" that similarly combined the essential science along with clean energy solutions. The course reached more than 30,000 students in the first semester of 2014. More recently the ETOM team has partnered with the National Council for Science and the Environment (NCSE) to develop "READ for the EARTH," an NSF EAGER project, offering campuses the opportunity to adopt Alley's book, the ETOM videos (including "How To Talk To An Ostrich"), NCSE's www.CAMELclimatechange.org web site and other resources for both formal and informal uses. Some campuses have used the book with honors classes, and some are exploring adapting ETOM as a first year reading experience for all freshman. Our presentation will share reactions to the MOOC, to the pilot phases of "READ for the EARTH" and present both qualitative and quantitative results. Some of the most

  4. Clean Air Act oversight: field hearings. Hearings before the Committee on Environment and Public Works, United States Senate, Ninety-Seventh Congress, First Session, June 27, 1981 Seattle, Washington, June 30, 1981 Randolph, Vermont, July 1, 1981 Albany, New York, July 1, 1981 Fairbanks, Alaska, Part 7

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    Part 7 of the field hearings report covers hearings held on June 27, 1981 in Seattle, Washington, June 30, 1981 in Randolph, Vermont, July 1, 1981 in Albany, NY, and also July 1, 1981 in Fairbanks, Alaska. A total of 122 witnesses appeared to express their views on reauthorizing the Clean Air Act and to suggest possible amendments. Witnesses represented federal and state agencies, local businesses, and public interest groups. Witnesses were asked to address the issues of health standards, the Prevention of Significant Deterioration rule, all air pollutants and the effects, and the lack of clear responsibility and flexibility in the Clean Air Act. Present at the Albany meeting were representatives from the Canadian government, which is concerned with the problem of transboundary pollution. The record includes the testimony and supporting materials submitted for the record. (DCK)

  5. Preperation for a Clean Surface

    Directory of Open Access Journals (Sweden)

    Aurimas Ralys

    2012-12-01

    Full Text Available The article reviews techniques for preparing clean surfaces used in the manufacturing process, considers the types of clean surfaces and their role in modern production and provides the classification methods of arranging such surfaces. The paper also discusses the principles of methods for solvent cleaning, aqueous cleaning, ultrasonic cleaning, precision cleaning and mechanical cleaning. The study focuses on the possibility of adjusting a clean surface using a water flow, including cavitation.Article in Lithuanian

  6. Preperation for a Clean Surface

    Directory of Open Access Journals (Sweden)

    Aurimas Ralys

    2013-02-01

    Full Text Available The article reviews techniques for preparing clean surfaces used in the manufacturing process, considers the types of clean surfaces and their role in modern production and provides the classification methods of arranging such surfaces. The paper also discusses the principles of methods for solvent cleaning, aqueous cleaning, ultrasonic cleaning, precision cleaning and mechanical cleaning. The study focuses on the possibility of adjusting a clean surface using a water flow, including cavitation.Article in Lithuanian

  7. Air Pollution Monitoring | Air Quality Planning & Standards ...

    Science.gov (United States)

    2016-06-08

    The basic mission of the Office of Air Quality Planning and Standards is to preserve and improve the quality of our nation's air. To accomplish this, OAQPS must be able to evaluate the status of the atmosphere as compared to clean air standards and historical information.

  8. Cleaning of South African coal using a compound dry cleaning apparatus

    Institute of Scientific and Technical Information of China (English)

    Li Haibin; Luo Zhenfu; Zhao Yuemin; Wu Wanchang; Zhang Cuiyu; Dai Ningning

    2011-01-01

    The compound dry cleaning principle is briefly described. A beneficiation test on South African coal was conducted using a model compound dry cleaning apparatus. Excellent results were obtained and the optimum operating parameters were determined. They are: an amplitude of 3.0 ram, a motor frequency of 47.5 Hz, an air volume of 50%, a transverse angle of 7°, and a longitudinal angle of -2°. These conditions yield a clean coal containing 11% ash and a coal production of 75%. The organic efficiency, η, is 95.86%. These results show that the South African coal can be separated effectively by compound dry cleaning, which will popularize the compound dry cleaning method.

  9. 基于PLC的洁净手术室净化空调新风机组自动控制的设计与实现%Design and implementation of automatic control for clean operating department clean air-conditioning fresh air units based on PLC

    Institute of Scientific and Technical Information of China (English)

    孙可; 刘杰; 王晨

    2011-01-01

    净化空调系统由新风机组、循环机组和送风管道组成,新风机组的作用是为手术室提供新风,并将室外新风进行初步净化及热湿处理后送入循环机组,经新风机组处理的新风和手术室回风在循环机组中再进行过滤及热湿处理后送入手术室.笔者成功设计了某市医院洁净手术室净化空调自动控制系统,并实现该系统的稳定运行.目前该项目设计的自动控制系统先已投入使用,运行效果良好,达到了设计的所有指标,取得了用户的认可.控制系统采用西门子S7-200系列PLC作为控制器,与上位机通过PROFIBUS现场总线技术实现通信.PLC是连接上位机与现场传感器、执行器等的桥梁,向上将底层传感器、变送器采集的温湿度、压差等信号上传至上位机,向下将上位机的控制信号传达给现场执行器.文章重点介绍了洁净手术室净化空调自动控制系统新风机组的组成及实时监控的实现.%Air cleaner system consists of fresh air handling unit, cycle unit and air pipe. The fresh air handling unit is to provide fresh air for the operating room, purify fundamentally the air from outside and send it to the cycle unit after hydrothermal process. The air processed through the fresh air handling unit, and the air in the operating room is going to be filtered again in the cycle unit and send it back to the operating room after another hydrothermal process. This paper succeeded in designing the automatic control system of air cleaner in the Da Shiqiao Central Hospital, and accomplished the stable operation of the system. SIMENS S7 - 200 series of PLC is the controller, corresponded with upper computer through PROFIBUS Fieldbus Technology. PLC is the bridge linking the upper computer, field sensor and actuator, which uploads the temperature, humidity and pressure differential collected by the sensor and trasmitter froth the lower-layer to the upper computer, and meanwhile transmits

  10. Cleaning and surface properties

    CERN Document Server

    Taborelli, M

    2007-01-01

    Principles of precision cleaning for ultra high vacuum applications are reviewed together with the techniques for the evaluation of surface cleanliness. Methods to verify the effectiveness of cleaning procedures are discussed. Examples are presented to illustrate the influence of packaging and storage on the recontamination of the surface after cleaning. Finally, the effect of contamination on some relevant surface properties, like secondary electron emission and wettability is presented.

  11. Clean Energy Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    For the past several years, the IEA and others have been calling for a clean energy revolution to achieve global energy security, economic growth and climate change goals. This report analyses for the first time progress in global clean energy technology deployment against the pathways that are needed to achieve these goals. It provides an overview of technology deployment status, key policy developments and public spending on RDD&D of clean energy technologies.

  12. Photocatalytic Solutions Create Self-Cleaning Surfaces

    Science.gov (United States)

    2013-01-01

    A Stennis Space Center researcher investigating the effectiveness of photocatalytic materials for keeping the Center's buildings free of grime turned to a solution created by PURETi Inc. of New York City. Testing proved successful, and NASA and the company now share a Dual Use Technology partnership. PURETi's coatings keep surfaces clean and purify surrounding air, eliminating pollution, odors, and microbes.

  13. 29 CFR 1917.154 - Compressed air.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Compressed air. 1917.154 Section 1917.154 Labor Regulations...) MARINE TERMINALS Related Terminal Operations and Equipment § 1917.154 Compressed air. Employees shall be... this part during cleaning with compressed air. Compressed air used for cleaning shall not exceed...

  14. Cleaning of solar cell arrays; Rausgeputzt fuer die Sonne

    Energy Technology Data Exchange (ETDEWEB)

    Petzold, Katrin

    2010-07-01

    The degree of soiling of solar cell arrays depends on the installation site, which may involve, e.g., animal shelter air, bird droppings or desert sand. Heavy rain has a cleaning effect, or else professional cleaning with osmotic water will be necessary. (orig.)

  15. Elements of Clean-room Technology and Contamination Control

    Directory of Open Access Journals (Sweden)

    J.C. Kapoor

    2003-07-01

    Full Text Available The heart of the clean room is the high efticiency particualte air (HEPA/ultra-low penetration air (ULPA filter, which provides the highest level of air cleaning ever achieved by a singleprocess step. Filter technology has seen tremendous growth in terms of ultimate performance and air handling capacity. Mere installation of ULPA filters of 99.99995 per cent efficiency for 0.2 um aerosol is not sufficient for achieving the desired performance of a clean room. Other design aspects like flow fields, face velocity, number of air changes, make-up air fractions and precise control of other environmental parameters (temperature, humidity, airflow, noise, vibrations, electrostatic discharge, etc. are equally important.

  16. Mechanical cleaning of graphene

    NARCIS (Netherlands)

    Goossens, A.M.; Calado, V.E.; Barreiro, A.; Watanabe, K.; Taniguchi, T.; Vandersypen, L.M.K.

    2012-01-01

    Contamination of graphene due to residues from nanofabrication often introduces background doping and reduces electron mobility. For samples of high electronic quality, post-lithography cleaning treatments are therefore needed. We report that mechanical cleaning based on contact mode atomic force mi

  17. 活性炭和植物吸收对室内空气甲醛净化的影响%Effect of the Activated Carbon and Plants Uptake on the Formaldehyde Cleaning in Indoor Air

    Institute of Scientific and Technical Information of China (English)

    廖秋实; 李苑; 杨宇婷; 张艳北; 史春玲; 秦红梅; 文静; 江长胜

    2011-01-01

    The indoor air pollution in urban resident is very serious, formaldehyde has become one of the most important indoor air pollutants in China. In this study, ivy (Scinda psusaureu), green dill (Hedera nepalensis van. Sinensis) and activated carbon were selected as the research objects, and the author used the closed chamber technique to study the absorption capacity of plants and chemicals on formaldehyde. The results showed that green dill, ivy and activated carbon were all good for indoor formaldehyde purification. 1 day later, the purifying efficiency decreased in the order as follows: ivy+activated carbon (formaldehyde cleaning rate was 38.27%)>ivy (34.31%)>green dill+activated carbon (32.20%)>green dill (5.61%)>activated carbon (3.73%). 10 days later, the purifying efficiency decreased in the order as follows: ivy+activated carbon (69.91%)>green dill+activated carbon (64.28%)>ivy (60.44%)>activated carbon (57.50%) >green dill (24.99%). Combining the plants and activated carbon had the better efficiency of formaldehyde cleaning rate than using plants or activated carbon singly, and long time had better effect than short time.%城市住宅的室内空气污染十分严重,甲醛已经成为中国目前室内空气中的首要污染物.以绿萝、常春藤与活性炭为研究对象,采用密闭箱法进行净化甲醛能力的研究.结果表明,绿萝、常春藤与活性炭均对室内空气中甲醛具有良好的净化作用,24 h后的甲醛净化能力大小依次为:常春藤+活性炭(甲醛去除率38.27%)>常春藤(34.31%)>绿萝+活性炭(32.20%)>绿萝(5.61%)>活性炭(3.73%);10天后的净化效果排序为:常春藤+活性炭(69.91%)>绿萝+活性炭(64.28%)>常春藤(60.44%)>活性炭(57.50%)>绿萝(24.99%).植物与活性炭联合作用对甲醛净化效果比单一用植物或活性炭效果好,而且长期作用比短期作用效果好.

  18. Handbook on Air Cleaning Particulate Removal

    Science.gov (United States)

    1952-09-01

    collisions are inelas- tic and if the particles are solid, e.g., A perfectly homogeneous aerosol would fumes of lead, zinc oxide, magnesium ox- have a ag of...EQUIPMENT 47 am T I J" mao AT Fig. 3.1-Assembly Drawing of the Modified Cascade Impacto ." Fig. 3.2-Modified Cascade Impactor - DisassembledFi.3-MdfeCace mct

  19. What is Clean Cities? October 2011 (Brochure)

    Energy Technology Data Exchange (ETDEWEB)

    2011-10-01

    Brochure describes the Clean Cities program and includes the contact information for its 85 coalitions. Sponsored by the U.S. Department of Energy's (DOE) Vehicle Technologies Program (VTP), Clean Cities is a government-industry partnership that reduces petroleum consumption in the transportation sector. Clean Cities contributes to the energy, environmental, and economic security of the United States by supporting local decisions to reduce our dependence on imported petroleum. Established in 1993 in response to the Energy Policy Act (EPAct) of 1992, the partnership provides tools and resources for voluntary, community-centered programs to reduce consumption of petroleum-based fuels. In nearly 100 coalitions, government agencies and private companies voluntarily come together under the umbrella of Clean Cities. The partnership helps all parties identify mutual interests and meet the objectives of reducing the use of petroleum, developing regional economic opportunities, and improving air quality. Clean Cities deploys technologies and practices developed by VTP. These include idle-reduction equipment, electric-drive vehicles, fuel economy measures, and renewable and alternative fuels, such as natural gas, liquefied petroleum gas (propane), electricity, hydrogen, biofuels, and biogas. Idle-reduction equipment is targeted primarily to buses and heavy-duty trucks, which use more than 2 billion gallons of fuel every year in the United States while idling. Clean Cities fuel economy measures include public education on vehicle choice and fuel-efficient driving practices.

  20. A Commercial IOTV Cleaning Study

    Science.gov (United States)

    2010-04-12

    quite clean and had a refreshing scent . The medium soiled garments (30%) also looked reasonably clean after one wash. The heavily soiled garments...and Solvair® Cleaning in cleaning soiled Improved Outer Tactical Vests (IOTV). Computer-controlled Wet Cleaning coupled with the use of LANADOL...to clean soiled IOTVs. Soldier Product Support Integration Directorate, ILSC U.S. Army Soldier Systems Center 15 Kansas Street, Natick, MA 01760

  1. 40 CFR 88.308-94 - Programmatic requirements for clean-fuel fleet vehicles.

    Science.gov (United States)

    2010-07-01

    ...-fuel fleet vehicles. 88.308-94 Section 88.308-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CLEAN-FUEL VEHICLES Clean-Fuel Fleet Program § 88.308-94 Programmatic requirements for clean-fuel fleet vehicles. (a) Multi-State nonattainment areas. The...

  2. Clean Water Act

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Clean Water Act (CWA) establishes the basic structure for regulating discharges of pollutants into U.S. waters and regulating quality standards for surface...

  3. Effective Cleaning Radius Studies

    Energy Technology Data Exchange (ETDEWEB)

    Churnetski, B.V.

    2001-10-15

    This report discusses results of testing done in the Savannah River Laboratory half tank and full tank mockup facilities using kaolin clay slurries and the relationship between cleaning radius and pump and slurry characteristics.

  4. Air filtration and indoor air quality

    DEFF Research Database (Denmark)

    Bekö, Gabriel

    2006-01-01

    decent ventilation and air cleaning/air filtration, high indoor air quality cannot be accomplished. The need for effective air filtration has increased with increasing evidence on the hazardous effects of fine particles. Moreover, the air contains gaseous pollutants, removal of which requires various air....... These contradictions should motivate manufacturers and researchers to develop new efficient filtration techniques and/or improve the existing ones. Development of low polluting filtration techniques, which are at the same time easy and inexpensive to maintain is the way forward in the future....

  5. Cleaning without chlorinated solvents

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, L.M.; Simandl, R.F.

    1994-12-31

    Because of health and environmental concerns, many regulations have been passed in recent years regarding the use of chlorinated solvents. The Oak Ridge Y-12 Plant has had an active program to find alternatives for these solvents used in cleaning applications for the past 7 years. During this time frame, the quantity of solvents purchased has been reduced by 92%. The program has been a twofold effort. Vapor degreasers used in batch cleaning-operations have been replaced by ultrasonic cleaning with aqueous detergent, and other organic solvents have been identified for use in hand-wiping or specialty operations. In order to qualify these alternatives for use, experimentation was conducted on cleaning ability as well as effects on subsequent operations such as welding, painting and bonding. Cleaning ability was determined using techniques such as X-ray photoelectron spectroscopy (XPS) and Fourier Transform Infrared Spectroscopy (FTIR) which are capable of examining monolayer levels of contamination on a surface. Solvents have been identified for removal of rust preventative oils, lapping oils, machining coolants, lubricants, greases, and mold releases. Solvents have also been evaluated for cleaning urethane foam spray guns, swelling of urethanes and swelling of epoxies.

  6. Solar-Panel Dust Accumulation and Cleanings

    Science.gov (United States)

    2005-01-01

    Air-fall dust accumulates on the solar panels of NASA's Mars Exploration Rovers, reducing the amount of sunlight reaching the solar arrays. Pre-launch models predicted steady dust accumulation. However, the rovers have been blessed with occasional wind events that clear significant amounts of dust from the solar panels. This graph shows the effects of those panel-cleaning events on the amount of electricity generated by Spirit's solar panels. The horizontal scale is the number of Martian days (sols) after Spirit's Jan. 4, 2005, (Universal Time) landing on Mars. The vertical scale indicates output from the rover's solar panels as a fraction of the amount produced when the clean panels first opened. Note that the gradual declines are interrupted by occasional sharp increases, such as a dust-cleaning event on sol 420.

  7. Appalachian clean coal technology consortium

    Energy Technology Data Exchange (ETDEWEB)

    Kutz, K.; Yoon, Roe-Hoan [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States)

    1995-11-01

    The Appalachian Clean Coal Technology Consortium (ACCTC) has been established to help U.S. coal producers, particularly those in the Appalachian region, increase the production of lower-sulfur coal. The cooperative research conducted as part of the consortium activities will help utilities meet the emissions standards established by the 1990 Clean Air Act Amendments, enhance the competitiveness of U.S. coals in the world market, create jobs in economically-depressed coal producing regions, and reduce U.S. dependence on foreign energy supplies. The research activities will be conducted in cooperation with coal companies, equipment manufacturers, and A&E firms working in the Appalachian coal fields. This approach is consistent with President Clinton`s initiative in establishing Regional Technology Alliances to meet regional needs through technology development in cooperation with industry. The consortium activities are complementary to the High-Efficiency Preparation program of the Pittsburgh Energy Technology Center, but are broader in scope as they are inclusive of technology developments for both near-term and long-term applications, technology transfer, and training a highly-skilled work force.

  8. Clean Elements in Abelian Rings

    Indian Academy of Sciences (India)

    Angelina Y M Chin

    2009-04-01

    Let be a ring with identity. An element in is said to be clean if it is the sum of a unit and an idempotent. is said to be clean if all of its elements are clean. If every idempotent in is central, then is said to be abelian. In this paper we obtain some conditions equivalent to being clean in an abelian ring.

  9. Columnar modelling of nucleation burst evolution in the convective boundary layer – first results from a feasibility study Part III: Preliminary results on physicochemical model performance using two "clean air mass" reference scenarios

    Directory of Open Access Journals (Sweden)

    O. Hellmuth

    2006-01-01

    Full Text Available In Paper I of four papers, a revised columnar high-order model to investigate gas-aerosol-turbulence interactions in the convective boundary layer (CBL was proposed. In Paper II, the model capability to predict first-, second- and third-order moments of meteorological variables in the CBL was demonstrated using available observational data. In the present Paper III, the high-order modelling concept is extended to sulphur and ammonia chemistry as well as to aerosol dynamics. Based on the previous CBL simulation, a feasibility study is performed using two "clean air mass" scenarios with an emission source at the ground but low aerosol background concentration. Such scenarios synoptically correspond to the advection of fresh post-frontal air in an anthropogenically influenced region. The aim is to evaluate the time-height evolution of ultrafine condensation nuclei (UCNs and to elucidate the interactions between meteorological and physicochemical variables in a CBL column. The scenarios differ in the treatment of new particle formation (NPF, whereas homogeneous nucleation according to the classical nucleation theory (CNT is considered. The first scenario considers nucleation of a binary system consisting of water vapour and sulphuric acid (H2SO4 vapour, the second one nucleation of a ternary system additionally involving ammonia (NH3. Here, the two synthetic scenarios are discussed in detail, whereas special attention is payed to the role of turbulence in the formation of the typical UCN burst behaviour, that can often be observed in the surface layer. The intercomparison of the two scenarios reveals large differences in the evolution of the UCN number concentration in the surface layer as well as in the time-height cross-sections of first-order moments and double correlation terms. Although in both cases the occurrence of NPF bursts could be simulated, the burst characteristics and genesis of the bursts are completely different. It is demonstrated

  10. Self-cleaning geopolymer concrete - A review

    Science.gov (United States)

    Norsaffirah Zailan, Siti; Mahmed, Norsuria; Bakri Abdullah, Mohd Mustafa Al; Sandu, Andrei Victor

    2016-06-01

    Concrete is the most widely used construction materials for building technology. However, cement production releases high amounts of carbon dioxide (CO2) to the atmosphere that leads to increasing the global warming. Thus, an alternative, environmental friendly construction material such as geopolymer concrete has been developed. Geopolymer concrete applies greener alternative binder, which is an innovative construction material that replaces the Portland cement. This technology introduced nano-particles such as nanoclay into the cement paste in order to improve their mechanical properties. The concrete materials also have been developed to be functioned as self-cleaning construction materials. The self-cleaning properties of the concrete are induced by introducing the photocatalytic materials such as titania (TiO2) and zinc oxide (ZnO). Self-cleaning concrete that contains those photocatalysts will be energized by ultraviolet (UV) radiation and accelerates the decomposition of organic particulates. Thus, the cleanliness of the building surfaces can be maintained and the air surrounding air pollution can be reduced. This paper briefly reviews about self-cleaning concrete.

  11. Research of the heliostat cleaning method

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiliang; Liu, Xiaobin [Himin Solar Energy Group Co., Ltd, Dezhou City (China); Wang, Zhifeng [CAS, Beijing (China). Inst. of Electrical Engineering

    2008-07-01

    Heliostat is the core component of Solar Power Tower system. It can straightly affect the efficiency of whole system. Because the heliostats run outside, and are discovered in the air, dust and dirt accumulates gradually on the surface of reflector. Then, it will gradually decrease the reflectivity of mirror so that reduce the whole efficiency. The article analyzed environment factors, and researched selecting availably cleaning method of heliostat for different conditions. (orig.)

  12. Investigation of influencing factors for bacterial density in air in clean operating room%洁净手术室术间空气细菌密度影响因素的调查

    Institute of Scientific and Technical Information of China (English)

    沈郁; 钱小毛; 冯惠娟; 陈小娣

    2011-01-01

    目的 了解洁净手术室术间空气细菌密度影响因素,探讨相应的护理对策.方法 对5间千级、万级和十万级手术室的45台手术进行动态条件下空气细菌检测,检测方法采用自然沉降法,结果计算后用CFU/m3表示.结果 所有手术间的术前空气含菌量均为0~23 CFU/m3,随着手术时间的延续空气细菌数逐渐增加,不同手术持续时间的术后检测:<1 h组为202~778 CFU/m3,1~2 h组为582~1332 CFU/m3,2~3 h组为672~1993 CFU/m3,<3 h组为713~2108 CFU/m3;不同手术人员数的术后检测:≤4人组为202~471 CFU/m3,5~8人组为355~901 CFU/m3,9~12人组为614~1443 CFU/m3,≥13人组为878~2108 CFU/m3;不同术中开门次数的术后检测:≤6次组为202~328 CFU/m3,7~11次组为562~889 CFU/m3,12~16次组为673~1870 CFU/m3,≥17次组为882~2108 CFU/m3.结论 影响术间空气细菌含量与手术时间长短,室内人员数,以及术间开门的次数有关,为了减缓手术过程空气细菌密度增大趋势,必须加强术间动态条件下的检测和一系列有效的预防措施.%OBJECTIVE To investigate the influencing factors of bacteria density in clean operating room environment and discuss the corresponding nursing measures. METHODS Air bacteria density of in 5 operating room (thousand level, ten thousand level, hundred thousand level) under dynamical condition in which 45 operations were undertaken was tested by means of natural precipitation method, and the result was named with CFU/m3. RESULTS The bacteria density in operating room before the surgery was between 0 to 23 CFU/m3. The number of bacteria was increased with the operating-time. Postoperative detection to surgery duration showed that, the bacteria density after surgery was 202~778 CFU/m3 ; in less than 1 hour group 1 to 2 hours group 582~ 1332 CFU/m3; 2 to 3 hours group 672~1993 CFU/m3 and more than 3 hours group 713~2108 CFU/m3. The postoperative detection to different

  13. Cleanly: trashducation urban system

    DEFF Research Database (Denmark)

    Reif, Inbal; Alt, Florian; Ramos, Juan David Hincapie

    Half the world's population is expected to live in urban areas by 2020. The high human density and changes in peoples' consumption habits result in an ever-increasing amount of trash that must be handled by governing bodies. Problems created by inefficient or dysfunctional cleaning services...

  14. Clean Cities Tools

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-12-19

    The U.S. Department of Energy's Clean Cities offers a large collection of Web-based tools on the Alternative Fuels Data Center. These calculators, interactive maps, and data searches can assist fleets, fuels providers, and other transportation decision makers in their efforts to reduce petroleum use.

  15. Neutrino Detection With CLEAN

    CERN Document Server

    McKinsey, D N

    2005-01-01

    This article describes CLEAN, an approach to the detection of low-energy solar neutrinos and neutrinos released from supernovae. The CLEAN concept is based on the detection of elastic scattering events (neutrino-electron scattering and neutrino-nuclear scattering) in liquified noble gases such as liquid helium, liquid neon, and liquid xenon, all of which scintillate brightly in the ultraviolet. Key to the CLEAN technique is the use of a thin film of wavelength-shifting fluor to convert the ultraviolet scintillation light to the visible. This allows the same liquid to be used as both a passive shielding medium and an active self-shielding detector, allowing lower intrinsic radioactive backgrounds at low energies. Liquid neon is a particularly promising medium for CLEAN. Because liquid neon has a high scintillation yield, has no long-lived radioactive isotopes, and can be easily purified by use of cold traps, it is an ideal medium for the detection of rare nuclear events. In addition, neon is inexpensive, dense...

  16. WINDOW-CLEANING

    CERN Multimedia

    Environmental Section / ST-TFM

    2001-01-01

    The two-month window-cleaning session on the Meyrin, Prévessin and LEP sites will soon begin. The cleaning contractors will work from Monday to Saturday, every week from 4.00 a.m. to 8.00 p.m. The work will be organised so as to disturb users as little as possible. In any event, a work notice will be left in each office 24 hours beforehand. To prevent any damage to documents or items which could occur despite the precautions taken, please clear completely the window-sills and the area immediately around them. If, however, for valid reasons, the work cannot be done on the scheduled day, please inform the Environmental Section by telephoning: 73753 / 74233 / 72242 If you are going to be absent during this two-month period, we should be grateful if you would clear the above mentioned areas before your departure. REMINDER To allow more thorough cleaning of the entrance doors to buildings and also facilitate the weekly work of the cleaning contractors, we ask you to make use of the notice boards at the...

  17. Clean Energy Solutions Center Services

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  18. Clean slate corrective action investigation plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The Clean Slate sites discussed in this report are situated in the central portion of the Tonopah Test Range (TTR), north of the Nevada Test Site (NTS) on the northwest portion of the Nellis Air Force Range (NAFR) which is approximately 390 kilometers (km) (240 miles [mi]) northwest of Las Vegas, Nevada. These sites were the locations for three of the four Operation Roller Coaster experiments. These experiments evaluated the dispersal of plutonium in the environment from the chemical explosion of a plutonium-bearing device. Although it was not a nuclear explosion, Operation Roller Coaster created some surface contamination which is now the subject of a corrective action strategy being implemented by the Nevada Environmental Restoration Project (NV ERP) for the U.S. Department of Energy (DOE). Corrective Action Investigation (CAI) activities will be conducted at three of the Operation Roller Coaster sites. These are Clean Slate 1 (CS-1), Clean Slate 2 (CS-2), and Clean Slate 3 (CS-3) sites, which are located on the TTR. The document that provides or references all of the specific information relative to the various investigative processes is called the Corrective Action Investigation Plan (CAIP). This CAIP has been prepared for the DOE Nevada Operations Office (DOE/NV) by IT Corporation (IT).

  19. Clean coal technology: Export finance programs

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-30

    Participation by US firms in the development of Clean Coal. Technology (CCT) projects in foreign countries will help the United States achieve multiple national objectives simultaneously--addressing critical goals related to energy, environmental technology, industrial competitiveness and international trade. US participation in these projects will result in an improved global environment, an improvement in the balance of payments and an increase in US jobs. Meanwhile, host countries will benefit from the development of economically- and environmentally-sound power facilities. The Clean Air Act Amendments of 1990 (Public Law 101-549, Section 409) as supplemented by a requirement in the Energy Policy Act of 1992 (Public Law 102-486, Section 1331(f)) requires that the Secretary of Energy, acting through the Trade Promotion Coordinating Committee Subgroup on Clean Coal Technologies, submit a report to Congress with information on the status of recommendations made in the US Department of Energy, Clean Coal Technology Export Programs, Report to the United States Congress, February 1992. Specific emphasis is placed on the adequacy of financial assistance for export of CCTS. This report fulfills the requirements of the Act. In addition, although this report focuses on CCT power projects, the issues it raises about the financing of these projects are also relevant to other CCT projects such as industrial applications or coal preparation, as well as to a much broader range of energy and environmental technology projects worldwide.

  20. Sustainable development with clean coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    This paper discusses the opportunities available with clean coal technologies. Applications include new power plants, retrofitting and repowering of existing power plants, steelmaking, cement making, paper manufacturing, cogeneration facilities, and district heating plants. An appendix describes the clean coal technologies. These include coal preparation (physical cleaning, low-rank upgrading, bituminous coal preparation); combustion technologies (fluidized-bed combustion and NOx control); post-combustion cleaning (particulate control, sulfur dioxide control, nitrogen oxide control); and conversion with the integrated gasification combined cycle.

  1. Multi-stage cleaning plant

    Energy Technology Data Exchange (ETDEWEB)

    Kullendorff, A.; Wikner, J.

    1980-12-09

    A cleaning plant positioned within an annular fluidized bed combustion chamber is divided into a plurality of separate cleaning stages, wherein a first stage is located adjacent the fluidized bed and additional stages are arranged within the first stage. Each stage comprises a plurality of separate cleaning devices which act in parallel, while cleaning devices of different stages act in series to remove debris from the combustion gases that exit from the fluidized bed combustion chamber.

  2. Cleaning of Free Machining Brass

    Energy Technology Data Exchange (ETDEWEB)

    Shen, T

    2005-12-29

    We have investigated four brightening treatments proposed by two cleaning vendors for cleaning free machining brass. The experimental results showed that none of the proposed brightening treatments passed the swipe test. Thus, we maintain the recommendation of not using the brightening process in the cleaning of free machining brass for NIF application.

  3. A Clean Market

    Institute of Scientific and Technical Information of China (English)

    MAGGIECHEN

    2004-01-01

    If you have US$1 million, do you invest in car production or cleaning car emissions? More cars than ever are hitting the roads and demand is rising.Cleaner cars are being called for, as the government strives to reduce car emission. So there is an obvious market both for cars and for new emission control technologies.Theoretically, you should make money by investing in either of them in China today.

  4. CLEAN: CLustering Enrichment ANalysis

    Directory of Open Access Journals (Sweden)

    Medvedovic Mario

    2009-07-01

    Full Text Available Abstract Background Integration of biological knowledge encoded in various lists of functionally related genes has become one of the most important aspects of analyzing genome-wide functional genomics data. In the context of cluster analysis, functional coherence of clusters established through such analyses have been used to identify biologically meaningful clusters, compare clustering algorithms and identify biological pathways associated with the biological process under investigation. Results We developed a computational framework for analytically and visually integrating knowledge-based functional categories with the cluster analysis of genomics data. The framework is based on the simple, conceptually appealing, and biologically interpretable gene-specific functional coherence score (CLEAN score. The score is derived by correlating the clustering structure as a whole with functional categories of interest. We directly demonstrate that integrating biological knowledge in this way improves the reproducibility of conclusions derived from cluster analysis. The CLEAN score differentiates between the levels of functional coherence for genes within the same cluster based on their membership in enriched functional categories. We show that this aspect results in higher reproducibility across independent datasets and produces more informative genes for distinguishing different sample types than the scores based on the traditional cluster-wide analysis. We also demonstrate the utility of the CLEAN framework in comparing clusterings produced by different algorithms. CLEAN was implemented as an add-on R package and can be downloaded at http://Clusteranalysis.org. The package integrates routines for calculating gene specific functional coherence scores and the open source interactive Java-based viewer Functional TreeView (FTreeView. Conclusion Our results indicate that using the gene-specific functional coherence score improves the reproducibility of the

  5. Clean Power on Tap

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    China adopts the most advanced nuclear power technologies to meet long-term energy needs Nuclear power has taken center stage in China’s nationwide cam-paign to develop new and clean energy sources. In the latest effort, Chinese state-owned nuclear power giants invested over 40 billion yuan ($5.86 billion) as an initial funding injection to build a new plant under the

  6. Clean steels for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S.

    1995-03-01

    Fusion energy production has an inherent advantage over fission: a fuel supply with reduced long term radioactivity. One of the leading candidate materials for structural applications in a fusion reactor is a tungsten stabilized 9% chromium Martensitic steel. This alloy class is being considered because it offers the opportunity to maintain that advantage in the reactor structure as well as provide good high temperature strength and radiation induced swelling and embrittlement resistance. However, calculations indicate that to obtain acceptable radioactivity levels within 500 years after service, clean steel will be required because the niobium impurity levels must be kept below about 2 appm and nickel, molybdenum, nitrogen, copper, and aluminum must be intentionally restricted. International efforts are addressing the problems of clean steel production. Recently, a 5,000 kg heat was vacuum induction melted in Japan using high purity commercial raw materials giving niobium levels less than 0.7 appm. This paper reviews the need for reduced long term radioactivity, defines the advantageous properties of the tungsten stabilized Martensitic steel class, and describes the international efforts to produce acceptable clean steels.

  7. Air Pollution Primer. Revised Education.

    Science.gov (United States)

    Corman, Rena

    This revised and updated book is written to inform the citizens on the nature, causes, and effects of air pollution. It is written in terms familiar to the layman with the purpose of providing knowledge and motivation to spur community action on clean air policies. Numerous charts and drawings are provided to support discussion of air pollution…

  8. Clean Industrial Room for Drift Tube Assembling

    CERN Document Server

    Glonti, GL; Evtoukhovitch, P G; Kroa, G; Manz, A; Potrap, I N; Rihter, P; Stoletov, G D; Tskhadadze, E G; Chepurnov, V F; Chirkov, A V; Shelkov, G A

    2001-01-01

    Description of a clean industrial room for assembly of drift tubes for the muon spectrometer of the ATLAS experiment is presented. High quality specifications on the detectors to be produced demanded creation of a workplace with stable temperature and humidity, as well as minimum quantity of dust in the room. Checking of parameters of intra-room air during long period of continuous work has been confirmed correctness of the designed characteristics of the climatic system installed in the clean room. The room large volum (\\sim 190 m^3), the powerful and flexible climatic system, and simplicity of service allow assembling of detectors with length up to 5 m. Subsequent checking of functionality of the assembled detectors has shown high quality of assembling (the amount of rejected tubes does not exceed 2 %). It demonstrates conformity to the assembling quality requirements for mass production of drift chambers for the muon spectrometer.

  9. ANALYSIS ON TECHNOLOGICAL PROCESSES CLEANING OIL PIPELINES

    Directory of Open Access Journals (Sweden)

    Mariana PǍTRAŞCU

    2015-05-01

    Full Text Available In this paper the researches are presented concerning the technological processes of oil pipelines.We know several technologies and materials used for cleaning the sludge deposits, iron and manganese oxides, dross, stone, etc.de on the inner walls of drinking water pipes or industries.For the oil industry, methods of removal of waste materials and waste pipes and liquid and gas transport networks are operations known long, tedious and expensive. The main methods and associated problems can be summarized as follows: 1 Blowing with compressed air.2 manual or mechanical brushing, sanding with water or dry.3 Wash with water jet of high pressure, solvent or chemical solution to remove the stone and hard deposits.4 The combined methods of cleaning machines that use water jets, cutters, chains, rotary heads cutters, etc.

  10. CFD simulation and energy efficient analysis of stratified cleaning in large-space clean factory buildings%高大洁净厂房分层净化CFD模拟与节能性分析

    Institute of Scientific and Technical Information of China (English)

    董秀芳; 肖武; 赵彬

    2012-01-01

    分析了高大洁净厂房的空间特点、使用时间特点、净化负荷特点,提出了在高度上分层的净化空调方案.采用CFD模拟了某高大洁净厂房采用分层净化空调时的气流组织,浓度场、温度场的模拟结果表明,该方案适用于高大洁净厂房.%Analyses the characteristics of space, service time and cleaning load in the building, and provides the stratified cleaning air conditioning scheme. Simulates the air distribution of stratified cleaning air conditioning in a large-space clean factory building with CFD. The concentration and temperature fields obtained show that the stratified cleaning air conditioning scheme suits for large-space clean factory buildings.

  11. Clean electricity from photovoltaics

    CERN Document Server

    Green, Martin A

    2015-01-01

    The second edition of Clean Electricity from Photovoltaics , first published in 2001, provides an updated account of the underlying science, technology and market prospects for photovoltaics. All areas have advanced considerably in the decade since the first edition was published, which include: multi-crystalline silicon cell efficiencies having made impressive advances, thin-film CdTe cells having established a decisive market presence, and organic photovoltaics holding out the prospect of economical large-scale power production. Contents: The Past and Present (M D Archer); Limits to Photovol

  12. Flue Gas Cleaning

    DEFF Research Database (Denmark)

    Fehrmann, Rasmus

    2014-01-01

    and sulfuric acid in the atmosphere causing precipitation of acid rain resulting in death of forests and destruction of buildings and monuments in addition to human health problems. The most common state-of-the-art methods applied today industrially for cleaning of flue gases will be addressed, including wet......-time. But the problems may also be attacked by new materials like supported ionic liquid phase (SILP) gas absorbers where the pollutants may be selectively absorbed, desorbed and finally converted to useful mineral acids of commercial grade – really a green waste-to-value approach that we persue instead...

  13. 77 FR 21911 - Approval and Promulgation of Implementation Plans; State of Arizona; Prevention of Air Pollution...

    Science.gov (United States)

    2012-04-12

    ... Air Pollution Emergency Episodes AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... of Arizona to address the requirements regarding air pollution emergency episodes in Clean Air Act... air pollution emergency episodes and adequate contingency plans to implement such authority...

  14. Numerical and experimental study of pulse-jet cleaning in fabric filters

    DEFF Research Database (Denmark)

    O. Andersen, B.; Nielsen, N. F.; Walther, J. H.

    2016-01-01

    Pulse-jet cleaning and understanding of the complex physics are essential when designing fabric filters used for air pollution control. Today, low-pressure cleaning is of particular interest due to demand for reduced compressed air consumption. Pulse-jet cleaned fabric filters have been studied...... for many years by experimental investigation and to a limited extent by Computational Fluid Dynamics (CFD). The majority of the studies have focused on high-pressure cleaning systems, and the CFD models presented are so far two-dimensional (2D). In the work presented here, pulse-jet cleaning of low....... The validated CFD model reveals the strong compressible effects, a highly transient behaviour, the formation of compressible vortex rings and the shock cell phenomenon within the overexpanded supersonic jet. The cleaning nozzles and venturi design aid or oppose the pulse-pressure within the bags, and this plays...

  15. International Clean Energy Coalition

    Energy Technology Data Exchange (ETDEWEB)

    Erin Skootsky; Matt Gardner; Bevan Flansburgh

    2010-09-28

    In 2003, the National Association of Regulatory Utility Commissioners (NARUC) and National Energy Technology Laboratories (NETL) collaboratively established the International Clean Energy Coalition (ICEC). The coalition consisting of energy policy-makers, technologists, and financial institutions was designed to assist developing countries in forming and supporting local approaches to greenhouse gas mitigation within the energy sector. ICEC's work focused on capacity building and clean energy deployment in countries that rely heavily on fossil-based electric generation. Under ICEC, the coalition formed a steering committee consisting of NARUC members and held a series of meetings to develop and manage the workplan and define successful outcomes for the projects. ICEC identified India as a target country for their work and completed a country assessment that helped ICEC build a framework for discussion with Indian energy decisionmakers including two follow-on in-country workshops. As of the conclusion of the project in 2010, ICEC had also conducted outreach activities conducted during United Nations Framework Convention on Climate Change (UNFCCC) Ninth Conference of Parties (COP 9) and COP 10. The broad goal of this project was to develop a coalition of decision-makers, technologists, and financial institutions to assist developing countries in implementing affordable, effective and resource appropriate technology and policy strategies to mitigate greenhouse gas emissions. Project goals were met through international forums, a country assessment, and in-country workshops. This project focused on countries that rely heavily on fossil-based electric generation.

  16. 32 CFR 989.30 - Air quality.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Air quality. 989.30 Section 989.30 National... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.30 Air quality. Section 176(c) of the Clean Air Act..., Air Quality Compliance. 10 10 See footnote 1 to § 989.1....

  17. Clean coal technologies market potential

    Energy Technology Data Exchange (ETDEWEB)

    Drazga, B. (ed.)

    2007-01-30

    Looking at the growing popularity of these technologies and of this industry, the report presents an in-depth analysis of all the various technologies involved in cleaning coal and protecting the environment. It analyzes upcoming and present day technologies such as gasification, combustion, and others. It looks at the various technological aspects, economic aspects, and the various programs involved in promoting these emerging green technologies. Contents: Industry background; What is coal?; Historical background of coal; Composition of coal; Types of coal; Environmental effects of coal; Managing wastes from coal; Introduction to clean coal; What is clean coal?; Byproducts of clean coal; Uses of clean coal; Support and opposition; Price of clean coal; Examining clean coal technologies; Coal washing; Advanced pollution control systems; Advanced power generating systems; Pulverized coal combustion (PCC); Carbon capture and storage; Capture and separation of carbon dioxide; Storage and sequestration of carbon dioxide; Economics and research and development; Industry initiatives; Clean Coal Power Initiative; Clean Coal Technology Program; Coal21; Outlook; Case Studies.

  18. 77 FR 53199 - California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request...

    Science.gov (United States)

    2012-08-31

    ... AGENCY California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request... California Air Resources Board (CARB) has notified EPA that it has developed an Advanced Clean Car program... into a single coordinated package of requirements for passenger cars, light-duty trucks and...

  19. Ultrasound cleaning of microfilters

    DEFF Research Database (Denmark)

    Hald, Jens; Bjørnø, Irina; Jensen, Leif Bjørnø

    1999-01-01

    The aim of the present work is to develop, design, and manufacture a high-power ultrasound transducer module to be used for preventing the blocking of plastic-based microfilters by organic materials, and possibly to prolong the lifetime of the filters in industry using the cavitation on the surface...... suitable for cleaning of microfilters without damaging the filter structure. The filter surface was studied using an optical microscope before and after the experiment. When high-power ultrasound (max. 75 W/cm2) was applied to the surface of some microfilters, no visible damage was found, while others...... filters were damaged. The results of the laboratory experiments formed background for the final design of an ultrasound transducer module for use by foodstuff filtration plants. [This work was financed by the EU Project WAMBIO PL96-3257 (FAIR Programme).]...

  20. Quick and clean cloning.

    Science.gov (United States)

    Thieme, Frank; Marillonnet, Sylvestre

    2014-01-01

    Identification of unknown sequences that flank known sequences of interest requires PCR amplification of DNA fragments that contain the junction between the known and unknown flanking sequences. Since amplified products often contain a mixture of specific and nonspecific products, the quick and clean (QC) cloning procedure was developed to clone specific products only. QC cloning is a ligation-independent cloning procedure that relies on the exonuclease activity of T4 DNA polymerase to generate single-stranded extensions at the ends of the vector and insert. A specific feature of QC cloning is the use of vectors that contain a sequence called catching sequence that allows cloning specific products only. QC cloning is performed by a one-pot incubation of insert and vector in the presence of T4 DNA polymerase at room temperature for 10 min followed by direct transformation of the incubation mix in chemo-competent Escherichia coli cells.

  1. Flue gas cleaning chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Gutberlet, H. [VEBA Kraftwerke Ruhr AG, Gelsenkirchen (Germany)

    1996-12-01

    The introduction of modern flue gas cleaning technology into fossil-fueled power stations has repeatedly confronted the power station chemists with new and interesting problems over the last 15 - 20 years. Both flue gas desulphurization by lime washing and catalytic removal of nitrogen oxides are based on simple basic chemical reactions. Owing to the use of readily available starting materials, the production of safe, useful end products and, last but not least, the possibility of implementing all this on an industrial scale by means of efficient process engineering, limestone desulphurization and catalytic removal of nitrogen oxides dominate the world market and, little by little, are becoming still more widespread. The origin and thus the quality of fuels and starting materials, the firing method, the mode of operation and engineering peculiarities in each plant interact in a complex manner. Simple cause/effect relationships are frequently incapable of explaining phenomena; thinking in complex interrelationships is needed. (EG)

  2. Programmed Cleaning and Environmental Sanitation.

    Science.gov (United States)

    Gardner, John C., Ed.

    Maintenance of sanitation in buildings, plants, offices, and institutions; the selection of cleaning materials for these purposes; and the organization and supervision of the cleaning program are becoming increasingly complex and needful of a higher cost of handling. This book describes these problems and gives helpful information and guidance for…

  3. A Note on Clean Rings

    Institute of Scientific and Technical Information of China (English)

    Zhou Wang; Jianlong Chen

    2007-01-01

    Let R be a ring and g(x) a polynomial in C[x],where C=C(R) denotes the center of R.Camillo and Sim6n called the ring g(x)-clean if every element of R can be written as the sum of a unit and a root of g(x).In this paper,we prove that for a,b (E) C,the ring R is clean and b - a is invertible in R if and only if R is g1(x)-clean,where gl(x) = (x - a)(x - b).This implies that in some sense the notion of g(x)-clean rings in the Nicholson-Zhou Theorem and in the Camillo-Sim6n Theorem is indeed equivalent to the notion of clean rings.

  4. Quantification of perchloroethylene residues in dry-cleaned fabrics.

    Science.gov (United States)

    Sherlach, Katy S; Gorka, Alexander P; Dantzler, Alexa; Roepe, Paul D

    2011-11-01

    We have used a novel gas chromatography/mass spectrometry (GC/MS)-based approach to quantify perchloroethylene (PCE) residues in dry-cleaned fabrics. Residual PCE was extracted from fabric samples with methanol and concentration was calculated by the gas chromatographic peak area, standardized using PCE calibration data. Extracts examined were from samples of 100% wool, polyester, cotton, or silk, which were dry cleaned from one to six times in seven different Northern Virginia dry-cleaning establishments. Additional experiments were conducted to investigate the kinetics of PCE release in the extraction solvent and to the open air. We found that polyester, cotton, and wool retained ≥ µM levels of PCE, that these levels increased in successive dry-cleaning cycles, and that PCE is slowly volatilized from these fabrics under ambient room air conditions. We found that silk does not retain appreciable PCE. Measured differences across dry-cleaning establishments and fabric type suggest more vigorous monitoring of PCE residues may be warranted. Environ. Toxicol. Chem. 2011;30:2481-2487. © 2011 SETAC.

  5. Clean Metal Casting

    Energy Technology Data Exchange (ETDEWEB)

    Makhlouf M. Makhlouf; Diran Apelian

    2002-02-05

    The objective of this project is to develop a technology for clean metal processing that is capable of consistently providing a metal cleanliness level that is fit for a given application. The program has five tasks: Development of melt cleanliness assessment technology, development of melt contamination avoidance technology, development of high temperature phase separation technology, establishment of a correlation between the level of melt cleanliness and as cast mechanical properties, and transfer of technology to the industrial sector. Within the context of the first task, WPI has developed a standardized Reduced Pressure Test that has been endorsed by AFS as a recommended practice. In addition, within the context of task1, WPI has developed a melt cleanliness sensor based on the principles of electromagnetic separation. An industrial partner is commercializing the sensor. Within the context of the second task, WPI has developed environmentally friendly fluxes that do not contain fluorine. Within the context of the third task, WPI modeled the process of rotary degassing and verified the model predictions with experimental data. This model may be used to optimize the performance of industrial rotary degassers. Within the context of the fourth task, WPI has correlated the level of melt cleanliness at various foundries, including a sand casting foundry, a permanent mold casting foundry, and a die casting foundry, to the casting process and the resultant mechanical properties. This is useful in tailoring the melt cleansing operations at foundries to the particular casting process and the desired properties of cast components.

  6. Clean tracks for ATLAS

    CERN Multimedia

    2006-01-01

    First cosmic ray tracks in the integrated ATLAS barrel SCT and TRT tracking detectors. A snap-shot of a cosmic ray event seen in the different layers of both the SCT and TRT detectors. The ATLAS Inner Detector Integration Team celebrated a major success recently, when clean tracks of cosmic rays were detected in the completed semiconductor tracker (SCT) and transition radiation tracker (TRT) barrels. These tracking tests come just months after the successful insertion of the SCT into the TRT (See Bulletin 09/2006). The cosmic ray test is important for the experiment because, after 15 years of hard work, it is the last test performed on the fully assembled barrel before lowering it into the ATLAS cavern. The two trackers work together to provide millions of channels so that particles' tracks can be identified and measured with great accuracy. According to the team, the preliminary results were very encouraging. After first checks of noise levels in the final detectors, a critical goal was to study their re...

  7. Precision Cleaning - Path to Premier

    Science.gov (United States)

    Mackler, Scott E.

    2008-01-01

    ITT Space Systems Division s new Precision Cleaning facility provides critical cleaning and packaging of aerospace flight hardware and optical payloads to meet customer performance requirements. The Precision Cleaning Path to Premier Project was a 2007 capital project and is a key element in the approved Premier Resource Management - Integrated Supply Chain Footprint Optimization Project. Formerly precision cleaning was located offsite in a leased building. A new facility equipped with modern precision cleaning equipment including advanced process analytical technology and improved capabilities was designed and built after outsourcing solutions were investigated and found lacking in ability to meet quality specifications and schedule needs. SSD cleans parts that can range in size from a single threaded fastener all the way up to large composite structures. Materials that can be processed include optics, composites, metals and various high performance coatings. We are required to provide verification to our customers that we have met their particulate and molecular cleanliness requirements and we have that analytical capability in this new facility. The new facility footprint is approximately half the size of the former leased operation and provides double the amount of throughput. Process improvements and new cleaning equipment are projected to increase 1st pass yield from 78% to 98% avoiding $300K+/yr in rework costs. Cost avoidance of $350K/yr will result from elimination of rent, IT services, transportation, and decreased utility costs. Savings due to reduced staff expected to net $4-500K/yr.

  8. Comparing toxic air pollutant programs

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, S.C. [ECKENFELDER Inc., Greenville, SC (United States)

    1997-05-01

    This article compares state and federal toxic air pollutant programs. The Clean Air Act Ammendments created a program for the control of Hazardous Air Pollutants based on the establishment of control technology standards. State toxic programs can be classified into two categories: control technology-based and ambient concentration-based. Many states have opened to implement the MACT standards while enforcing their own state air toxics programs. Specific topics discussed include the following: the Federal air toxics program; existing state regulations; New Jersey Air Toxic Program; New York Toxics program.

  9. Quantitative Evaluation of Contamination on Dental Zirconia Ceramic by Silicone Disclosing Agents after Different Cleaning Procedures

    Directory of Open Access Journals (Sweden)

    Sebastian Wille

    2015-05-01

    Full Text Available The aim of this study was to evaluate the effectiveness of cleaning procedures for air-abraded zirconia after contamination with two silicone disclosing agents. Air-abraded zirconia ceramic specimens (IPS e.max ZirCAD were contaminated with either GC Fit Checker white or GC Fit Checker II. Untreated zirconia specimens were used as control. Afterwards the surfaces were cleaned either with waterspray or ultrasonically in 99% isopropanol or using a newly developed cleaning paste (Ivoclean. After cleaning X-ray photoelectron spectroscopy (XPS was performed and the relative peak intensities of Zr, C and Si were used for a qualitative comparison of the residuals. There was no significant difference between the two different silicone disclosing agents. An additional cleaning step with isopropanol led to a significantly lower amount of residuals on the surface, but an additional cleaning process with Ivoclean did not reduce the amount of carbon residuals in comparison to the isopropanol cleaning. Just the silicone amount on the surface was reduced. None of the investigated cleaning processes removed all residuals from the contaminated surface. Standard cleaning processes do not remove all residuals of the silicone disclosing agent from the surface. This may lead to a failure of the resin-ceramic bonding.

  10. CLEAN Technique for Polarimetric ISAR

    Directory of Open Access Journals (Sweden)

    M. Martorella

    2008-01-01

    Full Text Available Inverse synthetic aperture radar (ISAR images are often used for classifying and recognising targets. To reduce the amount of data processed by the classifier, scattering centres are extracted from the ISAR image and used for classifying and recognising targets. This paper addresses the problem of estimating the position and the scattering vector of target scattering centres from polarimetric ISAR images. The proposed technique is obtained by extending the CLEAN technique, which was introduced in radar imaging for extracting scattering centres from single-polarisation ISAR images. The effectiveness of the proposed algorithm, namely, the Polarimetric CLEAN (Pol-CLEAN is tested on simulated and real data.

  11. Laser ablative fluxless soldering (LAFS): 60Sn-40Pb solder wettability tests on laser cleaned OFHC copper substrates

    Energy Technology Data Exchange (ETDEWEB)

    Peebles, H. C.; Keicher, D. M.; Hosking, F. M.; Hlava, P. F.; Creager, N. A.

    1991-01-01

    OFHC copper substrates, cleaned by laser ablation under argon and helium gas, were tested for solder wettability by 60Sn-40Pb using an area-of-spread method. The wettability of copper surfaces cleaned under both argon and helium gas was found to equal or exceed the wettability obtained on this surface in air using a standard RMA flux. The area of spread on copper substrates cleaned under helium was eight times larger than the area of spread of substrates cleaned under argon. The enhanced spreading observed on the substrates cleaned under helium gas was found to be due to surface roughness. 11 refs., 8 figs., 2 tabs.

  12. 40 CFR 52.793 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.793 Section 52.793 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not met... air quality. (b) Regulations for preventing significant deterioration of air quality. The...

  13. 40 CFR 52.1180 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1180 Section 52.1180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  14. 40 CFR 52.2827 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2827 Section 52.2827 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  15. 40 CFR 52.2676 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2676 Section 52.2676 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  16. 40 CFR 52.2729 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2729 Section 52.2729 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  17. 40 CFR 52.1689 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1689 Section 52.1689 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  18. 40 CFR 52.632 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.632 Section 52.632 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not met... air quality. (b) Regulations for preventing significant deterioration of air quality. The...

  19. 40 CFR 52.1884 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1884 Section 52.1884 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  20. 40 CFR 52.1603 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1603 Section 52.1603 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  1. 40 CFR 52.432 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.432 Section 52.432 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not met... air quality. (b) Regulation for preventing significant deterioration of air quality. The provisions...

  2. 40 CFR 52.96 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.96 Section 52.96 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The State of Alaska Department of Environmental Conservation Air Quality... deterioration of air quality. (b) The requirements of sections 160 through 165 of the Clean Air Act are not...

  3. 40 CFR 52.499 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.499 Section 52.499 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  4. 40 CFR 52.2497 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2497 Section 52.2497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  5. 30 CFR 250.302 - Definitions concerning air quality.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Definitions concerning air quality. 250.302... Definitions concerning air quality. For purposes of §§ 250.303 and 250.304 of this part: Air pollutant means..., pursuant to section 109 of the Clean Air Act, national primary or secondary ambient air quality...

  6. 40 CFR 52.683 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.683 Section 52.683 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The State of Idaho Rules for Control of Air Pollution in Idaho, specifically... the Clean Air Act for preventing significant deterioration of air quality. (b) The requirements...

  7. 40 CFR 52.1234 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1234 Section 52.1234 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  8. 40 CFR 52.1165 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1165 Section 52.1165 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulation for preventing significant deterioration of air quality....

  9. 40 CFR 52.738 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.738 Section 52.738 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not met... air quality. (b) Regulations for preventing significant deterioration of air quality. The...

  10. 40 CFR 52.2779 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2779 Section 52.2779 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) Regulations for preventing significant deterioration of air quality....

  11. Hansen Cleaning Solvent Research Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Environmental regulation will force current baseline  precision cleaning solvent (AK-225) to be phased out starting 2015. We plan to develop  a new...

  12. Clean coal - a national urgency

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.M.; Sahai, R. [Indian Bureau of Mines, Nagpur (India). Technical Consultancy Division

    2000-07-01

    India is the third largest producer and consumer of coal in the world. Coal generally has a high ash content, thereby requiring that it be cleaned for proper use. Technological advances now make it possible to reduce pollution considerably, even as energy use increases. However, to reduce environmental impacts, technologies for cleaning coal before combustion need to be developed. The paper focuses on the need for clean coal production and the benefits associated with it. Although the country is rich in coal reserves, the generally inferior quality of coal will lead to its depletion if it is not used cleanly. Increasing the proportion of prepared coal from the current level of less than 5% (i.e. 10-11 million tonnes per annum) of all coal consumed will lead to a massive saving. This can be achieved if new washeries are set up, preferably near the coalfields. 2 figs.

  13. Tracking Clean Energy Progress 2013

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-01

    Tracking Clean Energy Progress 2013 (TCEP 2013) examines progress in the development and deployment of key clean energy technologies. Each technology and sector is tracked against interim 2020 targets in the IEA Energy Technology Perspectives 2012 2°C scenario, which lays out pathways to a sustainable energy system in 2050. Stark message emerge: progress has not been fast enough; large market failures are preventing clean energy solutions from being taken up; considerable energy efficiency remains untapped; policies need to better address the energy system as a whole; and energy-related research, development and demonstration need to accelerate. Alongside these grim conclusions there is positive news. In 2012, hybrid-electric vehicle sales passed the 1 million mark. Solar photovoltaic systems were being installed at a record pace. The costs of most clean energy technologies fell more rapidly than anticipated.

  14. Efficient methods of piping cleaning

    Directory of Open Access Journals (Sweden)

    Orlov Vladimir Aleksandrovich

    2014-01-01

    Full Text Available The article contains the analysis of the efficient methods of piping cleaning of water supply and sanitation systems. Special attention is paid to the ice cleaning method, in course of which biological foil and various mineral and organic deposits are removed due to the ice crust buildup on the inner surface of water supply and drainage pipes. These impurities are responsible for the deterioration of the organoleptic properties of the transported drinking water or narrowing cross-section of drainage pipes. The co-authors emphasize that the use of ice compared to other methods of pipe cleaning has a number of advantages due to the relative simplicity and cheapness of the process, economical efficiency and lack of environmental risk. The equipment for performing ice cleaning is presented, its technological options, terms of cleansing operations, as well as the volumes of disposed pollution per unit length of the water supply and drainage pipelines. It is noted that ice cleaning requires careful planning in the process of cooking ice and in the process of its supply in the pipe. There are specific requirements to its quality. In particular, when you clean drinking water system the ice applied should be hygienically clean and meet sanitary requirements.In pilot projects, in particular, quantitative and qualitative analysis of sediments adsorbed by ice is conducted, as well as temperature and the duration of the process. The degree of pollution of the pipeline was estimated by the volume of the remote sediment on 1 km of pipeline. Cleaning pipelines using ice can be considered one of the methods of trenchless technologies, being a significant alternative to traditional methods of cleaning the pipes. The method can be applied in urban pipeline systems of drinking water supply for the diameters of 100—600 mm, and also to diversion collectors. In the world today 450 km of pipelines are subject to ice cleaning method.Ice cleaning method is simple

  15. 2012 Clean Energy: Project Summaries

    OpenAIRE

    Asian Development Bank

    2013-01-01

    This report summarizes the investments in clean energy made by the operations departments of the Asian Development Bank (ADB) in 2012, condensing information from project databases and formal reports in an easy-to-reference format. This report was prepared by ADB’s Clean Energy Program which provides the cohesive agenda that encompasses and guides ADB’s lending and non-lending assistance, initiatives, and plan of action for sustainable growth in Asia and the Pacific.

  16. Clean Energy Solutions Center (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Reategui, S.

    2012-07-01

    The Clean Energy Ministerial launched the Clean Energy Solutions Center in April, 2011 for major economy countries, led by Australia and U.S. with other CEM partners. Partnership with UN-Energy is extending scope to support all developing countries: 1. Enhance resources on policies relating to energy access, small to medium enterprises (SMEs), and financing programs; 2. Offer expert policy assistance to all countries; 3. Expand peer to peer learning, training, and deployment and policy data for developing countries.

  17. Efficient methods of piping cleaning

    OpenAIRE

    Orlov Vladimir Aleksandrovich; Nechitaeva Valentina Anatol'evna; Bogomolova Irina Olegovna; Shaykhetdinova Yuliya Aleksandrovna; Daminova Yuliya Farikhovna

    2014-01-01

    The article contains the analysis of the efficient methods of piping cleaning of water supply and sanitation systems. Special attention is paid to the ice cleaning method, in course of which biological foil and various mineral and organic deposits are removed due to the ice crust buildup on the inner surface of water supply and drainage pipes. These impurities are responsible for the deterioration of the organoleptic properties of the transported drinking water or narrowing cross-section of d...

  18. Clean Energy Application Center

    Energy Technology Data Exchange (ETDEWEB)

    Freihaut, Jim

    2013-09-30

    The Mid Atlantic Clean Energy Application Center (MACEAC), managed by The Penn State College of Engineering, serves the six states in the Mid-Atlantic region (Pennsylvania, New Jersey, Delaware, Maryland, Virginia and West Virginia) plus the District of Columbia. The goals of the Mid-Atlantic CEAC are to promote the adoption of Combined Heat and Power (CHP), Waste Heat Recovery (WHR) and District Energy Systems (DES) in the Mid Atlantic area through education and technical support to more than 1,200 regional industry and government representatives in the region. The successful promotion of these technologies by the MACEAC was accomplished through the following efforts; (1)The MACEAC developed a series of technology transfer networks with State energy and environmental offices, Association of Energy Engineers local chapters, local community development organizations, utilities and, Penn State Department of Architectural Engineering alumni and their firms to effectively educate local practitioners about the energy utilization, environmental and economic advantages of CHP, WHR and DES; (2) Completed assessments of the regional technical and market potential for CHP, WHR and DE technologies application in the context of state specific energy prices, state energy and efficiency portfolio development. The studies were completed for Pennsylvania, New Jersey and Maryland and included a set of incentive adoption probability models used as a to guide during implementation discussions with State energy policy makers; (3) Using the technical and market assessments and adoption incentive models, the Mid Atlantic CEAC developed regional strategic action plans for the promotion of CHP Application technology for Pennsylvania, New Jersey and Maryland; (4) The CHP market assessment and incentive adoption model information was discussed, on a continuing basis, with relevant state agencies, policy makers and Public Utility Commission organizations resulting in CHP favorable incentive

  19. Development of Megasonic cleaning for silicon wafers. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, A.

    1980-09-01

    The major goals to develop a cleaning and drying system for processing at least 2500 three-in.-diameter wafers per hour and to reduce the process cost were achieved. The new system consists of an ammonia-hydrogen peroxide bath in which both surfaces of 3/32-in.-spaced, ion-implanted wafers are cleaned in quartz carriers moved on a belt past two pairs of Megasonic transducers. The wafers are dried in the novel room-temperature, high-velocity air dryer in the same carriers used for annealing. A new laser scanner was used effectively to monitor the cleaning ability on a sampling basis. The following factors contribute to the improved effectiveness of the process: (1) recirculation and filtration of the cleaning solution permit it to be used for at least 100,000 wafers with only a relatively small amount of chemical make-up before discarding; (2) uniform cleanliness is achieved because both sides of the wafer are Megasonically scrubbed to remove particulate impurities; (3) the novel dryer permits wafers to be dried in a high-velocity room-temperature air stream on a moving belt in their quartz carriers; and (4) the personnel safety of such a system is excellent and waste disposal has no adverse ecological impact. With the addition of mechanical transfer arms, two systems like the one developed will produce enough cleaned wafers for a 30-MW/year production facility. A projected scale-up well within the existing technology would permit a system to be assembled that produces about 12,745 wafers per hour; about 11 such systems, each occupying about 110 square feet, would be needed for each cleaning stage of a 500-MW/year production facility.

  20. 40 CFR 257.3-7 - Air.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Air. 257.3-7 Section 257.3-7... and Practices § 257.3-7 Air. (a) The facility or practice shall not engage in open burning of... 110 of the Clean Air Act, as amended. (c) As used in this section “open burning” means the...

  1. Mechanisms of single bubble cleaning.

    Science.gov (United States)

    Reuter, Fabian; Mettin, Robert

    2016-03-01

    The dynamics of collapsing bubbles close to a flat solid is investigated with respect to its potential for removal of surface attached particles. Individual bubbles are created by nanosecond Nd:YAG laser pulses focused into water close to glass plates contaminated with melamine resin micro-particles. The bubble dynamics is analysed by means of synchronous high-speed recordings. Due to the close solid boundary, the bubble collapses with the well-known liquid jet phenomenon. Subsequent microscopic inspection of the substrates reveals circular areas clean of particles after a single bubble generation and collapse event. The detailed bubble dynamics, as well as the cleaned area size, is characterised by the non-dimensional bubble stand-off γ=d/Rmax, with d: laser focus distance to the solid boundary, and Rmax: maximum bubble radius before collapse. We observe a maximum of clean area at γ≈0.7, a roughly linear decay of the cleaned circle radius for increasing γ, and no cleaning for γ>3.5. As the main mechanism for particle removal, rapid flows at the boundary are identified. Three different cleaning regimes are discussed in relation to γ: (I) For large stand-off, 1.8substrate and remove particles without significant contact of the gas phase. (II) For small distances, γsubstrate are driven by the jet impact with its subsequent radial spreading, and by the liquid following the motion of the collapsing and rebounding bubble wall. Both flows remove particles. Their relative timing, which depends sensitively on the exact γ, appears to determine the extension of the area with forces large enough to cause particle detachment. (III) At intermediate stand-off, 1.1substrate, but acts with cleaning mechanisms similar to an effective small γ collapse: particles are removed by the jet flow and the flow induced by the bubble wall oscillation. Furthermore, the observations reveal that the extent of direct bubble gas phase contact to the solid is partially smaller than the

  2. Air/Water Purification

    Science.gov (United States)

    1992-01-01

    After 18 years of research into air/water pollution at Stennis Space Center, Dr. B. C. Wolverton formed his own company, Wolverton Environmental Services, Inc., to provide technology and consultation in air and water treatment. Common houseplants are used to absorb potentially harmful materials from bathrooms and kitchens. The plants are fertilized, air is purified, and wastewater is converted to clean water. More than 100 U.S. communities have adopted Wolverton's earlier water hyacinth and artificial marsh applications. Catfish farmers are currently evaluating the artificial marsh technology as a purification system.

  3. Megasonic cleaning: effect of dissolved gas properties on cleaning

    Science.gov (United States)

    Shende, Hrishi; Singh, Sherjang; Baugh, James; Dietze, Uwe; Dress, Peter

    2013-06-01

    Current and future lithography techniques require complex imaging improvement strategies. These imaging improvement strategies require printing of sub-resolution assist-features (SRAF) on photomasks. The size of SRAF's has proven to be the main limiting factor in using high power Megasonic cleaning process on photomasks. These features, due to high aspect ratio are more prone to damage at low Megasonic frequencies and at high Megasonic powers. Additionally the non-uniformity of energy dissipated during Megasonic cleaning is a concern for exceeding the damage threshold of the SRAFs. If the cavitation events during Megasonic cleaning are controlled in way to dissipate uniform energy, better process control can be achieved to clean without damage. The amount and type of gas dissolved in the cleaning liquid defines the cavitation behavior. Some of the gases possess favourable solubility and adiabatic properties for stable and controlled cavitation behaviour. This paper particularly discusses the effects of dissolved Ar gas on Megasonic characteristics. The effect of Ar Gas is characterized by measuring acoustic energy and Sonoluminscense. The phenomenon is further verified with pattern damage studies.

  4. Electromagnetically Clean Solar Arrays

    Science.gov (United States)

    Stem, Theodore G.; Kenniston, Anthony E.

    2008-01-01

    The term 'electromagnetically clean solar array' ('EMCSA') refers to a panel that contains a planar array of solar photovoltaic cells and that, in comparison with a functionally equivalent solar-array panel of a type heretofore used on spacecraft, (1) exhibits less electromagnetic interferences to and from other nearby electrical and electronic equipment and (2) can be manufactured at lower cost. The reduction of electromagnetic interferences is effected through a combination of (1) electrically conductive, electrically grounded shielding and (2) reduction of areas of current loops (in order to reduce magnetic moments). The reduction of cost is effected by designing the array to be fabricated as a more nearly unitary structure, using fewer components and fewer process steps. Although EMCSAs were conceived primarily for use on spacecraft they are also potentially advantageous for terrestrial applications in which there are requirements to limit electromagnetic interference. In a conventional solar panel of the type meant to be supplanted by an EMCSA panel, the wiring is normally located on the back side, separated from the cells, thereby giving rise to current loops having significant areas and, consequently, significant magnetic moments. Current-loop geometries are chosen in an effort to balance opposing magnetic moments to limit far-0field magnetic interactions, but the relatively large distances separating current loops makes full cancellation of magnetic fields problematic. The panel is assembled from bare photovoltaic cells by means of multiple sensitive process steps that contribute significantly to cost, especially if electomagnetic cleanliness is desired. The steps include applying a cover glass and electrical-interconnect-cell (CIC) sub-assemble, connecting the CIC subassemblies into strings of series-connected cells, laying down and adhesively bonding the strings onto a panel structure that has been made in a separate multi-step process, and mounting the

  5. Prizes awarded in fiscal 1999 by the Minister for International Trade and Industry on factories having applied excellent energy management. Energy conservation by installing fuel cell power generation facilities utilizing methane gas generated from waste water treatment plants / Improvements toward a clean room and energy saving air conditioning system; 1999 nendo energy kanri yuryo kojo tsusho sangyo daijin hyosho jusho. 1999 nendo shigen energy sho chokan hyosho jusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    In order to achieve energy conservation in a waste water treatment plant in a brewery factories, an anaerobic treatment facility was introduced, and a fuel cell power generation facility effectively utilizing methane gas generated from the anaerobic waste water treatment plant was installed. This has resulted in large reduction in the operating number of blowers in the waste water treatment facility of activated sludge system. In addition, electric power, steam, and hot water generated from the fuel cells are effectively utilized as the factory utility. In energy conservation in an optical communication device manufacturing factory, the fan filter unit system was adopted, having been changed from the circulation air conditioner, a conventional type air conditioning system. The present system is a circulation system integrating the fan with the filter, making it possible to circulate air in the room to perform control of temperature, humidity, and dust in a clean room. Thus, the system has eliminated the circulating air conditioner, and reduced the air conditioner capacity by 42% and power consumption by 58.6% compared with those in the conventional circulation system. (NEDO)

  6. Nonpneumonic, short-incubation-period Legionellosis (Pontiac fever) in men who cleaned a steam turbine condenser.

    Science.gov (United States)

    Fraser, D W; Deubner, D C; Hill, D L; Gilliam, D K

    1979-08-17

    Pontiac fever affected ten men who had cleaned a steam turbine condenser with compressed air. Previous epidemics of Pontiac fever and Legionnaires' disease--both caused by Legionella Pneumophila (proposed sp. nov.)--involved "airborne spread" from air-conditioning cooling towers or evaporative condensers. Aerosols of contaminated water in heat-rejection systems appear to be important sources of epidemic legionellosis.

  7. Are Breast Surgical Operations Clean or Clean Contaminated?

    Science.gov (United States)

    Kataria, Kamal; Bagdia, Amit; Srivastava, Anurag

    2015-12-01

    The breast surgeries are classically taught as clean surgical procedures. The infection rates following breast surgery ranges from 3 to 15 %, which is much higher than infection rates after clean surgery (ranging from 1.5 to 3 %). This high infection rate following breast surgery can be explained by opening of the ductal system to outside world through nipple similar to the gastrointestinal and genitourinary system. We conducted a systematic review of infection following breast surgeries. We searched various randomized controlled trials, meta-analysis, and Cochrane Reviews over PubMed and Medline via the Internet. These evidences were found to support the thesis, "Breast surgeries need to be reclassified as clean-contaminated". We recommend the use of prophylactic antibiotics in breast surgery.

  8. Implementation Science to Accelerate Clean Cooking for Public Health

    Science.gov (United States)

    Rosenthal, Joshua; Balakrishnan, Kalpana; Bruce, Nigel; Chambers, David; Graham, Jay; Jack, Darby; Kline, Lydia; Masera, Omar; Mehta, Sumi; Mercado, Ilse Ruiz; Neta, Gila; Pattanayak, Subhrendu; Puzzolo, Elisa; Petach, Helen; Punturieri, Antonello; Rubinstein, Adolfo; Sage, Michael; Sturke, Rachel; Shankar, Anita; Sherr, Kenny; Smith, Kirk; Yadama, Gautam

    2017-01-01

    Summary: Clean cooking has emerged as a major concern for global health and development because of the enormous burden of disease caused by traditional cookstoves and fires. The World Health Organization has developed new indoor air quality guidelines that few homes will be able to achieve without replacing traditional methods with modern clean cooking technologies, including fuels and stoves. However, decades of experience with improved stove programs indicate that the challenge of modernizing cooking in impoverished communities includes a complex, multi-sectoral set of problems that require implementation research. The National Institutes of Health, in partnership with several government agencies and the Global Alliance for Clean Cookstoves, has launched the Clean Cooking Implementation Science Network that aims to address this issue. In this article, our focus is on building a knowledge base to accelerate scale-up and sustained use of the cleanest technologies in low- and middle-income countries. Implementation science provides a variety of analytical and planning tools to enhance effectiveness of clinical and public health interventions. These tools are being integrated with a growing body of knowledge and new research projects to yield new methods, consensus tools, and an evidence base to accelerate improvements in health promised by the renewed agenda of clean cooking. PMID:28055947

  9. Physical Cleaning of Lakhra Coal by Dense Medium Separation Method

    Directory of Open Access Journals (Sweden)

    Sikandar Ali Channa

    2015-07-01

    Full Text Available This research is an attempt to upgrade Lakhra Lignite Coal using ?Dense Medium Separation? technique, to make it techno-environmentally acceptable product for different industries. The air-dried samples of ROM (Run of Mine coal were crushed, screened, ground and subjected to initial analysis and specific gravity based sink-float tests. The initial analysis of air-dried samples shows the average values of moisture 19%, volatile matter 22.33%, ash 27.41%, fixed carbon 31.26% and sulphur 4.98%. The investigational results of sink-float analysis indicate that physical cleaning at particle size range from -5.6 to +0.3 mm and 75% clean coal recovery can potentially reduce the ash yield and sulphur content of Lakhra coal up to 41 and 42.4% respectively. This washed coal is techno-environmentally acceptable yield and simultaneously qualifies the quality parameters set by various industries of Pakistan

  10. 75 FR 72963 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Volatile...

    Science.gov (United States)

    2010-11-29

    ... AGENCY 40 CFR Part 52 Approval and Promulgation of Air Quality Implementation Plans; Maryland; Control of Volatile Organic Compound Emissions From Industrial Solvent Cleaning Operations; Withdrawal of Direct Final... standards for industrial solvent cleaning operations that satisfy the reasonably available...

  11. Cleaning properties of dry adhesives

    Institute of Scientific and Technical Information of China (English)

    J.; P.; DíAZ; TéLLEZ; D.; SAMEOTO; C.; MENON

    2010-01-01

    In this paper we present a study into the cleaning properties of synthetic dry adhesives. We have manufactured the adhesive micro-fibres through a low-cost, high yield fabrication method using Sylgard 184 Polydimethylsiloxane (PDMS) as the structural material. We deliberately contaminated the adhesive samples with different sized particles in the micro and macro scales and tested different cleaning methods for their efficacy with respect to each particle size. We investigated different cleaning methods, which included the use of wax moulding, vibration and pressure sensitive adhesives. For adhesion testing we used a custom system with a linear stage and a force sensor indenting a hemispherical probe into the adhesive surface and measuring the pull-off force. To characterize the cleaning efficacy we visually inspected each sample in a microscope and weighed the samples with a microgram-accuracy analytical balance. Results showed that the moulding method induced adhesion recovery in a greater percentage than the other cleaning methods and even helped with the recovery of collapsed posts in some cases. On the other hand pressure sensitive adhesives seem to have the upper hand with regards to certain particle sizes that can potentially pose problems with the moulding method.

  12. Cleaning of porous filters in fossilized bed reactors; Estudio de limpieza de filtros porosos en reactores de lecho fluidizado

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigo Otero, A.; Sancho Rod, J.

    1965-07-01

    In this report are established the optimum working conditions of a filter cleaning system by blow back. For this purpose it was determined in the first place the blow back air rate necessary to have a good cleaning. The reasons for which it was not possible until now to control the pressure in a fluidized bed calcination reactor are analyzed and a criteria is established to calculate the optimum floe necessary to clean efficiently a porous by this procedures. (Author)

  13. Field Validation of Visual Cleaning Performance Indicator (VCPI) Technology

    Science.gov (United States)

    2007-08-31

    test panels. Panels sets included 2024-T3 aluminum alloy sheet (Air Force platform), and primer coated HY80 steel alloy (Navy platform). 1. Weight...Cleaning Petfmmance Indicator (VCPI) tedmology as a means to verify surface cleanliness on aluminum and painted steel alloys. The VCPI technology...the surface cleanliness of unpainted structures fabricated from aluminum and steel alloys. In concept, the VCPI technology represents an innovative

  14. Laser cleaning of tungsten ribbon

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Aniruddha, E-mail: nontee65@rediffmail.com [Advanced Fuel Fabrication Facility, Bhabha Atomic Research Centre, Tarapur, Maharashtra, 401504 (India); Sonar, V.R.; Das, D.K.; Bhatt, R.B.; Behere, P.G.; Afzal, Mohd.; Kumar, Arun [Advanced Fuel Fabrication Facility, Bhabha Atomic Research Centre, Tarapur, Maharashtra, 401504 (India); Nilaya, J.P.; Biswas, D.J. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Trombay, 400085 (India)

    2014-07-01

    Removal of a thin oxide layer from a tungsten ribbon was achieved using the fundamental, second and third harmonic radiation from a Q- switched Nd-YAG laser. It was found that beyond the threshold, oxide removal was achieved at all wavelengths for a wide range of fluence values. The removal mechanism of the oxide layer was found to be critically dependent on both wavelength and fluence of the incident radiation and has been identified as ejection or sublimation. The un-cleaned and cleaned surfaces were analyzed by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDS) and atomic force microscopy (AFM). Laser cleaned tungsten ribbons were used in a thermal ionization mass spectrometer (TIMS) to determine isotopic composition of Neodymium atoms.

  15. Hyperbolic Divergence Cleaning for SPH

    CERN Document Server

    Tricco, Terrence S

    2012-01-01

    We present SPH formulations of Dedner et al's hyperbolic/parabolic divergence cleaning scheme for magnetic and velocity fields. Our implementation preserves the conservation properties of SPH which is important for stability. This is achieved by deriving an energy term for the Psi field, and imposing energy conservation on the cleaning subsystem of equations. This necessitates use of conjugate operators for divB and gradPsi in the numerical equations. For both the magnetic and velocity fields, the average divergence error in the system is reduced by an order of magnitude with our cleaning algorithm. Divergence errors in SPMHD are maintained to < 1%, even for realistic 3D applications with a corresponding gain in numerical stability. Density errors for an oscillating elliptic water drop using weakly compressible SPH are reduced by a factor of two.

  16. Clean Coal Diesel Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Robert Wilson

    2006-10-31

    A Clean Coal Diesel project was undertaken to demonstrate a new Clean Coal Technology that offers technical, economic and environmental advantages over conventional power generating methods. This innovative technology (developed to the prototype stage in an earlier DOE project completed in 1992) enables utilization of pre-processed clean coal fuel in large-bore, medium-speed, diesel engines. The diesel engines are conventional modern engines in many respects, except they are specially fitted with hardened parts to be compatible with the traces of abrasive ash in the coal-slurry fuel. Industrial and Municipal power generating applications in the 10 to 100 megawatt size range are the target applications. There are hundreds of such reciprocating engine power-plants operating throughout the world today on natural gas and/or heavy fuel oil.

  17. Experimental researches and comparison on aerodynamic parameters and cleaning efficiency of multi-level multi-channel cyclone

    Directory of Open Access Journals (Sweden)

    Aleksandras Chlebnikovas

    2015-10-01

    Full Text Available Multi-level multi-channel cyclone – the lately designed air cleaning device that can remove ultra-fine 20 μm particulatematter (PM from dusted air and reach over 95% of the overall cleaning efficiency. Multi-channel cyclone technology is based on centrifugal forces and has the resulting additional filtering process operation. Multi-level structure of cyclone allows to achieve higher air flow cleaning capacity at the same dimensions of the device, thus saving installation space required for the job, production and operating costs. Studies have examined the air flow parameters change in one–, two– and three–levels multichannel cyclone. These constructions differ according to the productivity of cleaned air under the constant peripheral and transitional (50/50 case air flow relations. Accordance with the results of air flow dynamics – velocity distribution of multi-channel cyclone, aerodynamic resistance and efficiency can be judged on the flow turbulence, the flow channel cross-section and select the most appropriate application. Cleaning efficiency studies were carried out using fine granite and wood ashes PM. The maximum cleaning efficiency was 93.3%, at an average of 4.5 g/m3, the aerodynamic resistance was equal to 1525 Pa.

  18. Laser paper cleaning: the method of cleaning historical books

    Science.gov (United States)

    Zekou, Evangelini; Tsilikas, Ioannis; Chatzitheodoridis, Elias; Serafetinides, Alexander A.

    2016-01-01

    Conservation of cultural heritage treasures is the most important issue for transferring knowledge to the public through the next generation of students, academics, and researchers. Although this century is authenticating e-books and information by means of electronic text, still historical manuscripts as content as well as objects are the main original recourses of keeping a record of this transformation. The current work focuses on cleaning paper samples by the application of pulsed light, which is interventional. Experiments carried out using paper samples that are artificially colonized with Ulocladium chartarum. Paper is treated by Nd:YAG laser light. The available wavelength is 1064 nm, at various fluences, repetition rates and number of pulses. Two types of paper are stained with fungi colonies, which grow on substrates of clean paper, as well as on paper with ink text. The first type of paper is Whatman No.1056, which is closer to pure cellulose. The second type of paper is a page of a cultural heritage book published in 1926. Cleaning is performed using laser irradiation, thus defining the damage threshold of each sample. The treatment on paper Watman showed a yellowing, especially on areas with high concentration of fungi. The second sample was more durable to the exposure, performing the best results at higher fluences. Eventually, the paper samples are characterized, with optical microscopy and SEM/EDX analyses, prior to and after cleaning.

  19. Alternative, Green Processes for the Precision Cleaning of Aerospace Hardware

    Science.gov (United States)

    Maloney, Phillip R.; Grandelli, Heather Eilenfield; Devor, Robert; Hintze, Paul E.; Loftin, Kathleen B.; Tomlin, Douglas J.

    2014-01-01

    weighed again showing typical contaminant deposition levels of approximately 0.00300g per part. They were then cleaned by the solvent or process being tested and then weighed a third time which allowed for the calculation of the cleaning efficiency of the test solvent or process.Based on preliminary experiments, five solvents (ethanol, isopropanol, acetone, ethyl acetate, and tert-butyl acetate) were down selected for further testing. When coupled with ultrasonic agitation, these solvents removed hydrocarbon contaminants as well as Vertrel MCA and showed improved removal of perfluorinated greases. Supercritical carbon dioxide did an excellent job dissolving each of the five contaminants but did a poor job of removing Teflon particles found in the perfluorinated greases. Plasma cleaning efficiency was found to be dependent on which supply gas was used, exposure time, and gas pressure. Under optimized conditions it was found that breathing air, energized to the plasma phase, was able to remove nearly 100% of the contamination.These findings indicate that alternative cleaning methods are indeed able to achieve precision levels of cleanliness. Currently, our team is working with a commercial cleaning company to get independent verification of our results. We are also evaluating the technical and financial aspects of scaling these processes to a size capable of supporting the future cleaning needs of KSC.

  20. Sociology: Clean-energy conservatism

    Science.gov (United States)

    McCright, Aaron M.

    2017-03-01

    US conservatives receive a steady stream of anti-environmental messaging from Republican politicians. However, clean-energy conservatives sending strong counter-messages on energy issues could mobilize moderate conservatives to break away from the dominant right-wing defence of fossil fuels.

  1. Laser cleaning on Roman coins

    Science.gov (United States)

    Drakaki, E.; Karydas, A. G.; Klinkenberg, B.; Kokkoris, M.; Serafetinides, A. A.; Stavrou, E.; Vlastou, R.; Zarkadas, C.

    Ancient metal objects react with moisture and environmental chemicals to form various corrosion products. Because of the unique character and high value of such objects, any cleaning procedure should guarantee minimum destructiveness. The most common treatment used is mechanical stripping, in which it is difficult to avoid surface damage when employed. Lasers are currently being tested for a wide range of conservation applications. Since they are highly controllable and can be selectively applied, lasers can be used to achieve more effective and safer cleaning of archaeological artifacts and protect their surface details. The basic criterion that motivated us to use lasers to clean Roman coins was the requirement of pulsed emission, in order to minimize heat-induced damages. In fact, the laser interaction with the coins has to be short enough, to produce a fast removal of the encrustation, avoiding heat conduction into the substrate. The cleaning effects of three lasers operating at different wavelengths, namely a TEA CO2 laser emitting at 10.6 μm, an Er:YAG laser at 2.94 μm, and a 2ω-Nd:YAG laser at 532 nm have been compared on corroded Romans coins and various atomic and nuclear techniques have also been applied to evaluate the efficiency of the applied procedure.

  2. Cleaning Validation of Fermentation Tanks

    DEFF Research Database (Denmark)

    Salo, Satu; Friis, Alan; Wirtanen, Gun

    2008-01-01

    Reliable test methods for checking cleanliness are needed to evaluate and validate the cleaning process of fermentation tanks. Pilot scale tanks were used to test the applicability of various methods for this purpose. The methods found to be suitable for validation of the clenlinees were visula o...

  3. Clean coal initiatives in Indiana

    Science.gov (United States)

    Bowen, B.H.; Irwin, M.W.; Sparrow, F.T.; Mastalerz, Maria; Yu, Z.; Kramer, R.A.

    2007-01-01

    Purpose - Indiana is listed among the top ten coal states in the USA and annually mines about 35 million short tons (million tons) of coal from the vast reserves of the US Midwest Illinois Coal Basin. The implementation and commercialization of clean coal technologies is important to the economy of the state and has a significant role in the state's energy plan for increasing the use of the state's natural resources. Coal is a substantial Indiana energy resource and also has stable and relatively low costs, compared with the increasing costs of other major fuels. This indigenous energy source enables the promotion of energy independence. The purpose of this paper is to outline the significance of clean coal projects for achieving this objective. Design/methodology/approach - The paper outlines the clean coal initiatives being taken in Indiana and the research carried out at the Indiana Center for Coal Technology Research. Findings - Clean coal power generation and coal for transportation fuels (coal-to-liquids - CTL) are two major topics being investigated in Indiana. Coking coal, data compilation of the bituminous coal qualities within the Indiana coal beds, reducing dependence on coal imports, and provision of an emissions free environment are important topics to state legislators. Originality/value - Lessons learnt from these projects will be of value to other states and countries.

  4. Wanted: Clean Coal Burning Technology

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    China is intent on developing clean coal burning technology, an objective it can achieve through installing desulfurization facilities at coal-burning power plants that will control SO2 emissions and environmental pollution. According to kuo Yi, deputy director general of the Department of Science and Technology of the State Environmental Protection Agency, China is a major coal-buming country:

  5. Pollute first, clean up later?

    NARCIS (Netherlands)

    Azadi, Hossein; Verheijke, Gijs; Witlox, Frank

    2011-01-01

    There is a growing concern with regard to sustainability in emerging economies like China. The Chinese growth is characterized by a strategy which is known as "pollute first, clean up later". Here we show that based on this strategy, the pollution alarm can often be postponed by a tremendous economi

  6. Partnership for a Clean Future

    Institute of Scientific and Technical Information of China (English)

    WANG HAIRONG

    2010-01-01

    @@ Having lived in China for almost three decades,Sabina Brady is a de facto China hand.Currently,she is the cxecutive director of the U.S.-China Energy Cooperation Program (ECP),a nonprofit organization that engages in market development and promotion of clean energy within the framework of China-U.S.bilateral government commitments on the environrnent and energy.

  7. Teaming up for Clean Energy

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    On October 22, the China Institute of Strategy and Management and the U.S. Brookings Institution jointly held the China-U.S. Strategic Forum on Clean Energy Cooperation. At the opening session of the forum, Zheng Bijian, Chairman of the China Institute of Strategy and Management, gave a keynote speech. Edited excerpts follow:

  8. Cleaning the Diesel Engine Emissions

    DEFF Research Database (Denmark)

    Christensen, Thomas Budde

    This paper examines how technologies for cleaning of diesel emission from road vehicles can be supported by facilitating a technology push in the Danish automotive emission control industry. The European commission is at present preparing legislation for the euro 5 emission standard (to be enforc...

  9. 40 CFR 52.382 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Significant deterioration of air quality. 52.382 Section 52.382 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not...

  10. 40 CFR 52.833 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.833 Section 52.833 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are met... for preventing significant deterioration of air quality. The provisions of § 52.21 except paragraph...

  11. 40 CFR 52.1116 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1116 Section 52.1116 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... deterioration of air quality. (b) The following provisions of 40 CFR 52.21 are hereby incorporated and made...

  12. 40 CFR 52.2528 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2528 Section 52.2528 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of Sections 160 through 165 of the Clean Air... Quality Deterioration. (b) Regulations for Preventing Significant Deterioration of Air Quality,...

  13. 40 CFR 52.2303 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2303 Section 52.2303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The plan submitted by Texas is approved as meeting the requirements of part C, Clean Air Act for preventing significant deterioration of air quality. The...

  14. 40 CFR 52.343 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.343 Section 52.343 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air Act are not met for the following categories of sources for preventing the significant deterioration of air...

  15. 40 CFR 52.1485 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.1485 Section 52.1485 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... include approvable procedures for preventing the significant deterioration of air quality. (b)...

  16. 40 CFR 52.884 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Significant deterioration of air quality. 52.884 Section 52.884 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of section 160 through 165 of the Clean Air Act, as...

  17. 40 CFR 52.1436 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Significant deterioration of air quality. 52.1436 Section 52.1436 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. The requirements of sections 160 through 165 of the Clean Air...

  18. 40 CFR 52.2451 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.2451 Section 52.2451 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Significant deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Air... Quality Deterioration. (b) Regulations for preventing significant deterioration of air quality....

  19. Review on Characterization and Mechanical Performance of Self-cleaning Concrete

    Directory of Open Access Journals (Sweden)

    Zailan Siti Norsaffirah

    2017-01-01

    Full Text Available Self-cleaning concrete is an effective alternative to provide cleaner environment which contribute to sustainability and towards a green environment. It is in accordance with the requirements of environmental issues on huge energy consumption and air pollution from carbon dioxide (CO2 emissions. Photocatalyst in self-cleaning concrete accelerates the decomposition of organic particulates, hence pollution could be reduced through photocatalytic degradation of gaseous pollutants. Mechanical performances of self-cleaning concrete were improved by adding photocatalytic materials. Self cleaning abilities were evaluated in the photocatalytic activity test under UV light and photocatalytic degradation of gaseous pollutant was measured by depollution test. This review aims to give an overview about the characteristics of photocatalytic materials and mechanical performances of self-cleaning concrete.

  20. Directional self-cleaning superoleophobic surface.

    Science.gov (United States)

    Zhao, Hong; Law, Kock-Yee

    2012-08-14

    In this work, we report the creation of a grooved surface comprising 3 μm grooves (height ~4 μm) separated by 3 μm from each other on a silicon wafer by photolithography. The grooved surface was then modified chemically with a fluorosilane layer (FOTS). The surface property was studied by both static and dynamic contact angle measurements using water, hexadecane, and a polyethylene wax ink as the probing liquids. Results show that the grooved surface is both superhydrophobic and superoleophobic. Its observed contact angles agree well with the calculated Cassie-Baxter angles. More importantly, we are able to make a replica of the composite wax ink-air interface and study it by SEM. Microscopy results not only show that the droplet of the wax ink "sits" on air in the composite interface but also further reveal that the ink drop actually pins underneath the re-entrant structure in the side wall of the grooved structure. Contact angle measurement results indicate that wetting on the grooved surface is anisotropic. Although liquid drops are found to have lower static and advancing contact angles in the parallel direction, the drops are found to be more mobile, showing smaller hysteresis and lower sliding angles (as compared to the FOTS wafer surface and a comparable 3-μm-diameter pillar array FOTS surface). The enhanced mobility is attributable to the lowering of the resistance against an advancing liquid because 50% of the advancing area is made of a solid strip where the liquid likes to wet. This also implies that the contact line for advancing is no longer smooth but rather is ragged, having the solid strip area leading the wetting and the air strip area trailing behind. This interpretation is supported by imaging the geometry of the contact lines using molten ink drops recovered from the sliding angle experiments in both the parallel and orthogonal directions. Because the grooved surface is mechanically stronger against mechanical abrasion, the self-cleaning

  1. Benchmarks of Global Clean Energy Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Sandor, Debra [National Renewable Energy Lab. (NREL), Golden, CO (United States); Chung, Donald [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keyser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mann, Margaret [National Renewable Energy Lab. (NREL), Golden, CO (United States); Engel-Cox, Jill [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-01-01

    The Clean Energy Manufacturing Analysis Center (CEMAC), sponsored by the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE), provides objective analysis and up-to-date data on global supply chains and manufacturing of clean energy technologies. Benchmarks of Global Clean Energy Manufacturing sheds light on several fundamental questions about the global clean technology manufacturing enterprise: How does clean energy technology manufacturing impact national economies? What are the economic opportunities across the manufacturing supply chain? What are the global dynamics of clean energy technology manufacturing?

  2. Clean Energy Infrastructure Educational Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Hallinan, Kevin; Menart, James; Gilbert, Robert

    2012-08-31

    The Clean Energy Infrastructure Educational Initiative represents a collaborative effort by the University of Dayton, Wright State University and Sinclair Community College. This effort above all aimed to establish energy related programs at each of the universities while also providing outreach to the local, state-wide, and national communities. At the University of Dayton, the grant has aimed at: solidfying a newly created Master's program in Renewable and Clean Energy; helping to establish and staff a regional sustainability organization for SW Ohio. As well, as the prime grantee, the University of Dayton was responsible for insuring curricular sharing between WSU and the University of Dayton. Finally, the grant, through its support of graduate students, and through cooperation with the largest utilities in SW Ohio enabled a region-wide evaluation of over 10,000 commercial building buildings in order to identify the priority buildings in the region for energy reduction. In each, the grant has achieved success. The main focus of Wright State was to continue the development of graduate education in renewable and clean energy. Wright State has done this in a number of ways. First and foremost this was done by continuing the development of the new Renewable and Clean Energy Master's Degree program at Wright State . Development tasks included: continuing development of courses for the Renewable and Clean Energy Master's Degree, increasing the student enrollment, and increasing renewable and clean energy research work. The grant has enabled development and/or improvement of 7 courses. Collectively, the University of Dayton and WSU offer perhaps the most comprehensive list of courses in the renewable and clean energy area in the country. Because of this development, enrollment at WSU has increased from 4 students to 23. Secondly, the grant has helped to support student research aimed in the renewable and clean energy program. The grant helped to solidify

  3. Ion Cleaning of Facets for Improving the Reliability of High Power 980 nm Semiconductor Lasers

    Institute of Scientific and Technical Information of China (English)

    SHU Xiong-Wen; XU Chen; TIAN Zeng-Xia; SHEN Guang-Di

    2006-01-01

    We report a simple and available way of improving the reliability of high power InGaAs 980 nm lasers by cleaning the facets using Ar ion before the protecting films have been coated. The Ar cleaning can remove the impurity and the oxide on the air-cleaved facets of laser diodes. It is proven that the way has marked effect on reducing the gradual degradation rate of laser diodes and improving the catastrophic-optical-damage threshold.

  4. An evaluation of alternative cleaning methods for removing an organic contaminant from a stainless steel part

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, J.L.

    1996-08-01

    As of December 1995, the manufacture of Freon, along with many other chlorofluorocarbons (CFCs), was prohibited by the Clean Air Act of 1990 (CAA). The ban of CFC solvents has forced manufacturers across the country to search for alternative metal cleaning techniques. The objective of this study was to develop a thorough, scientific based approach for resolving one specific manufacturer`s problem of removing organic contamination from a stainless steel part. This objective was accomplished with an approach that involved: (1) defining the problem, (2) identifying the process constraints, (3) researching alternate cleaning methods, (4) researching applicable government regulations, (5) performing a scientific evaluation and (6) drawing conclusions.

  5. Comparison of sampling procedures and microbiological and non-microbiological parameters to evaluate cleaning and disinfection in broiler houses.

    Science.gov (United States)

    Luyckx, K; Dewulf, J; Van Weyenberg, S; Herman, L; Zoons, J; Vervaet, E; Heyndrickx, M; De Reu, K

    2015-04-01

    Cleaning and disinfection of the broiler stable environment is an essential part of farm hygiene management. Adequate cleaning and disinfection is essential for prevention and control of animal diseases and zoonoses. The goal of this study was to shed light on the dynamics of microbiological and non-microbiological parameters during the successive steps of cleaning and disinfection and to select the most suitable sampling methods and parameters to evaluate cleaning and disinfection in broiler houses. The effectiveness of cleaning and disinfection protocols was measured in six broiler houses on two farms through visual inspection, adenosine triphosphate hygiene monitoring and microbiological analyses. Samples were taken at three time points: 1) before cleaning, 2) after cleaning, and 3) after disinfection. Before cleaning and after disinfection, air samples were taken in addition to agar contact plates and swab samples taken from various sampling points for enumeration of total aerobic flora, Enterococcus spp., and Escherichia coli and the detection of E. coli and Salmonella. After cleaning, air samples, swab samples, and adenosine triphosphate swabs were taken and a visual score was also assigned for each sampling point. The mean total aerobic flora determined by swab samples decreased from 7.7±1.4 to 5.7±1.2 log CFU/625 cm2 after cleaning and to 4.2±1.6 log CFU/625 cm2 after disinfection. Agar contact plates were used as the standard for evaluating cleaning and disinfection, but in this study they were found to be less suitable than swabs for enumeration. In addition to measuring total aerobic flora, Enterococcus spp. seemed to be a better hygiene indicator to evaluate cleaning and disinfection protocols than E. coli. All stables were Salmonella negative, but the detection of its indicator organism E. coli provided additional information for evaluating cleaning and disinfection protocols. Adenosine triphosphate analyses gave additional information about the

  6. Clean Cities Now Vol. 17, No. 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-05-24

    Biannual newsletter for the U.S. Department of Energy's Clean Cities initiative. The newsletter includes feature stories on advanced vehicle deployment, idle reduction, and articles on Clean Cities coalition successes across the country.

  7. Clean Cities Now Vol. 16.1

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-05-01

    Biannual newsletter for the U.S. Department of Energy's Clean Cities initiative. The newsletter includes feature stories on advanced vehicle deployment, idle reduction, and articles on Clean Cities coalition successes across the country.

  8. The MiniCLEAN Experiment

    Science.gov (United States)

    Wang, Jui-Jen (Ryan); Gold, Michael; Miniclean Collaboration

    2017-01-01

    The MiniCLEAN (Cryogenic Low-Energy Astrophysics with Noble liquid) dark matter experiment will exploit a single-phase liquid argon detector instrumented with 92 photomultiplier tubes placed in the cryogen with 4- π coverage of a 500 kg (150 kg) target (fiducial) mass. The detector design strategy emphasizes scalability to target masses of order 10 tons or more. It is designed also for a liquid neon target that allows for an independent verification of signal and background and a test of the expected dependence of the WIMP-nucleus interaction rate. For MiniCLEAN, PMT stability and calibration are essential. The Light-Emitting Diode (LED) based light injection system provide single photon for the calibration which can be performed in near real-time, providing a continuous monitor on the condition of the detector. This talk will summarize the status of detector and upcoming commissioning at SNOLAB in Sudbury, Canada.

  9. Clean Energy Solutions Center Services (Arabic Translation)

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This is an Arabic translation of the Clean Energy Solutions Center fact sheet. The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  10. 7 CFR 29.6007 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 29.6007 Section 29.6007 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6007 Clean. Tobacco is described as clean when it contains only...

  11. Clean Energy Manufacturing Analysis Center (CEMAC)

    Energy Technology Data Exchange (ETDEWEB)

    2015-12-01

    The U.S. Department of Energy's Clean Energy Manufacturing Analysis Center (CEMAC) provides objective analysis and up-to-date data on global supply chains and manufacturing of clean energy technologies. Policymakers and industry leaders seek CEMAC insights to inform choices to promote economic growth and the transition to a clean energy economy.

  12. Clean Energy Solutions Center Services (Chinese Translation)

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This is a Mandarin translation of the Clean Energy Solutions Center fact sheet. The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  13. Clean Energy Solutions Center Services (Vietnamese Translation)

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This is a Vietnamese translation of the Clean Energy Solutions Center fact sheet. The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  14. Clean Cities Now, Vol. 18, No. 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-01-19

    This is version 18.2 of Clean Cities Now, the official biannual newsletter of the Clean Cities program. Clean Cities is an initiative designed to reduce petroleum consumption in the transportation sector by advancing the use of alternative and renewable fuels, fuel economy improvements, idle-reduction measures, and new technologies, as they emerge.

  15. Clean Energy Solutions Center Services (Portuguese Translation)

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This is a Portuguese translation of the Clean Energy Solutions Center Services fact sheet. The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  16. Clean Energy Solutions Center Services (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-04-01

    The Clean Energy Solutions Center (Solutions Center) helps governments, advisors and analysts create policies and programs that advance the deployment of clean energy technologies. The Solutions Center partners with international organizations to provide online training, expert assistance, and technical resources on clean energy policy.

  17. Clean Energy Solutions Center Services (French Translation)

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-01

    This is a French translation of the Clean Energy Solutions Center fact sheet. The Solutions Center offers no-cost expert policy assistance, webinars and training forums, clean energy policy reports, data, and tools provided in partnership with more than 35 leading international and regional clean energy organizations.

  18. 48 CFR 36.512 - Cleaning up.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Cleaning up. 36.512... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.512 Cleaning up. The contracting officer shall insert the clause at 52.236-12, Cleaning Up, in solicitations and contracts when a...

  19. 7 CFR 51.606 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.606 Section 51.606 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Consumer Standards for Celery Stalks Definitions § 51.606 Clean. Clean means that the stalk is...

  20. 7 CFR 51.1553 - Fairly clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Fairly clean. 51.1553 Section 51.1553 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades of Potatoes 1 Definitions § 51.1553 Fairly clean. Fairly clean means that at least...

  1. 7 CFR 51.1581 - Fairly clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Fairly clean. 51.1581 Section 51.1581 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Consumer Standards for Potatoes Definitions § 51.1581 Fairly clean. Fairly clean means that from...

  2. 7 CFR 51.1316 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.1316 Section 51.1316 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Winter Pears 1 Definitions § 51.1316 Clean. Clean means free from excessive dirt, dust,...

  3. 7 CFR 29.2256 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 29.2256 Section 29.2256 Agriculture Regulations... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2256 Clean. Tobacco is described as clean when it contains only a normal amount of sand or soil particles....

  4. 7 CFR 51.1552 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.1552 Section 51.1552 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades of Potatoes 1 Definitions § 51.1552 Clean. Clean means that at least 90 percent of...

  5. 7 CFR 29.3507 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 29.3507 Section 29.3507 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 95) § 29.3507 Clean. Tobacco is described as clean when it contains only a normal amount of...

  6. 7 CFR 51.2288 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.2288 Section 51.2288 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Shelled English Walnuts (Juglans Regia) Definitions § 51.2288 Clean. Clean means that...

  7. 7 CFR 51.1867 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.1867 Section 51.1867 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Fresh Tomatoes 1 Definitions § 51.1867 Clean. Clean means that the tomato is practically...

  8. 7 CFR 51.2965 - Fairly clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Fairly clean. 51.2965 Section 51.2965 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades of Walnuts in the Shell Definitions § 51.2965 Fairly clean. Fairly clean means...

  9. 7 CFR 51.2654 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.2654 Section 51.2654 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades for Sweet Cherries 1 Definitions § 51.2654 Clean. Clean means that the cherries...

  10. 7 CFR 51.2083 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.2083 Section 51.2083 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades of Almonds in the Shell Definitions § 51.2083 Clean. Clean means that the shell...

  11. 7 CFR 29.1004 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 29.1004 Section 29.1004 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1004 Clean. Tobacco is described as clean when it contains only a normal amount of...

  12. 7 CFR 51.2118 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.2118 Section 51.2118 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Grades of Shelled Almonds Definitions § 51.2118 Clean. Clean means that the kernel...

  13. 7 CFR 29.3009 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 29.3009 Section 29.3009 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Clean. Tobacco is described as clean when it contains only a normal amount of sand or soil...

  14. 7 CFR 51.3061 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.3061 Section 51.3061 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Florida Avocados Definitions § 51.3061 Clean. Clean means that the avocado is practically...

  15. 7 CFR 51.1275 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.1275 Section 51.1275 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Summer and Fall Pears 1 Definitions § 51.1275 Clean. Clean means free from excessive...

  16. 7 CFR 51.570 - Clean.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Clean. 51.570 Section 51.570 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Standards for Celery Definitions § 51.570 Clean. Clean means that the stalk is practically free from dirt...

  17. Advanced air distribution

    DEFF Research Database (Denmark)

    Melikov, Arsen Krikor

    2011-01-01

    The aim of total volume air distribution (TVAD) involves achieving uniform temperature and velocity in the occupied zone and environment designed for an average occupant. The supply of large amounts of clean and cool air are needed to maintain temperature and pollution concentration at acceptable...... levels in the entire space, leading to increased energy consumption and the use of large and costly HVAC and duct systems. The performance of desk installed PV combined with background TVAD used for room temperature control has been studied in an office building located in a hot and humid climate....... Ventilation in hospitals is essential to decrease the risk of airborne cross-infection. At present, mixing air distribution at a minimum of 12 ach is used in infection wards. Advanced air distribution has the potential to aid in achieving healthy, comfortable and productive indoor environments at levels...

  18. Waterless Clothes-Cleaning Machine

    Science.gov (United States)

    Johnson, Glenn; Ganske, Shane

    2013-01-01

    A waterless clothes-cleaning machine has been developed that removes loose particulates and deodorizes dirty laundry with regenerative chemical processes to make the clothes more comfortable to wear and have a fresher smell. This system was initially developed for use in zero-g, but could be altered for 1-g environments where water or other re sources are scarce. Some of these processes include, but are not limited to, airflow, filtration, ozone generation, heat, ultraviolet light, and photocatalytic titanium oxide.

  19. Battery Technology Stores Clean Energy

    Science.gov (United States)

    2008-01-01

    Headquartered in Fremont, California, Deeya Energy Inc. is now bringing its flow batteries to commercial customers around the world after working with former Marshall Space Flight Center scientist, Lawrence Thaller. Deeya's liquid-cell batteries have higher power capability than Thaller's original design, are less expensive than lead-acid batteries, are a clean energy alternative, and are 10 to 20 times less expensive than nickel-metal hydride batteries, lithium-ion batteries, and fuel cell options.

  20. Milliken Clean Coal Technology Demonstration Project. Project performance summary, Clean Coal Technology Demonstration Program

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2002-11-30

    The New York State Electric & Gas Corporation (NYSEG) demonstrated a combination of technologies at its Milliken Station in Lansing, New York, designed to: (1) achieve high sulfur dioxide (SO2) capture efficiency, (2) bring nitrogen oxide (NOx) emissions into compliance with Clean Air Act Amendments of 1990 (CAAA), (3) maintain high station efficiency, and (4) eliminate waste water discharge. This project is part of the U.S. Department of Energy's (DOE) Clean Coal Technology Demonstration Program (CCTDP) established to address energy and environmental concerns related to coal use. DOE sought cost-shared partnerships with industry through five nationally competed solicitations to accelerate commercialization of the most promising advance coal-based power generation and pollution control technologies. The CCTDP, valued at over five billion dollars, has significantly leveraged federal funding by forging effective partnerships founded on sound principles. For every federal dollar invested, CCTDP participants have invested two dollars. These participants include utilities, technology developers, state governments, and research organizations. The project presented here was one of nine selected in January 1991 from 33 proposals submitted in response to the program's fourth solicitation.

  1. Establishment of a clean chemistry laboratory at JAERI. Clean laboratory for environmental analysis and research (CLEAR)

    Energy Technology Data Exchange (ETDEWEB)

    Hanzawa, Yukiko; Magara, Masaaki; Watanabe, Kazuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

    2003-02-01

    The JAERI has established a facility with a cleanroom: the Clean Laboratory for Environmental Analysis and Research (CLEAR). This report is an overview of the design, construction and performance evaluation of the CLEAR in the initial stage of the laboratory operation in June 2001. The CLEAR is a facility to be used for analyses of ultra trace amounts of nuclear materials in environmental samples for the safeguards, for the CTBT verification and for researches on environmental sciences. One of the special features of the CLEAR is that it meets double requirements of a cleanroom and for handling of nuclear materials. As another feature of the CLEAR, much attention was paid to the construction materials of the cleanroom for trace analysis of metal elements using considerable amounts of corrosive acids. The air conditioning and purification system, specially designed experimental equipment to provide clean work surfaces, utilities and safety systems are also demonstrated. The potential contamination from the completed cleanroom atmosphere during the analytical procedure was evaluated. It can be concluded that the CLEAR has provided a suitable condition for reliable analysis of ultra trace amounts of nuclear materials and other heavy elements in environmental samples. (author)

  2. 'How To' Clean Room Video

    Science.gov (United States)

    McCarty, Kaley Corinne

    2013-01-01

    One of the projects that I am completing this summer is a Launch Services Program intern 'How to' set up a clean room informational video. The purpose of this video is to go along with a clean room kit that can be checked out by employees at the Kennedy Space Center and to be taken to classrooms to help educate students and intrigue them about NASA. The video will include 'how to' set up and operate a clean room at NASA. This is a group project so we will be acting as a team and contributing our own input and ideas. We will include various activities for children in classrooms to complete, while learning and having fun. Activities that we will explain and film include: helping children understand the proper way to wear a bunny suit, a brief background on cleanrooms, and the importance of maintaining the cleanliness of a space craft. This project will be shown to LSP management and co-workers; we will be presenting the video once it is completed.

  3. Combining a Novel Computer Vision Sensor with a Cleaning Robot to Achieve Autonomous Pig House Cleaning

    DEFF Research Database (Denmark)

    Andersen, Nils Axel; Braithwaite, Ian David; Blanke, Mogens

    2005-01-01

    Cleaning of livestock buildings is the single most health-threatening task in the agricultural industry and a transition to robot-based cleaning would be instrumental to improving working conditions for employees. Present cleaning robots fall short on cleanness quality, as they cannot perform...

  4. Clean

    Institute of Scientific and Technical Information of China (English)

    何伟文

    2005-01-01

    Core competitiveness is a notion familiar to most managers with an MBA degree, These days, this is what is taught at renowned business schools and colleges. And in the real world,large and small enterprises are increasingly following this course of action, To concentrate on one or two single lines of business in most cases makes sense and boosts profit, There are, however,

  5. Measuring the Benefits of Clean Air and Water.

    Science.gov (United States)

    Kneese, Allen V.

    This book examines the current state of the art regarding benefits assessment, including such tools as bidding games, surveys, property-value studies, wage differentials, risk reduction evaluation, and mortality and morbidity cost estimation. It is based on research, sponsored by the United States Environmental Protection Agency, related to the…

  6. 77 FR 16548 - Clean Air Act Advisory Committee

    Science.gov (United States)

    2012-03-21

    ... diversity of perspectives on the committee (e.g., geographic, economic, social, cultural, educational, and... meetings, attend listening sessions with the Assistant Administrator or other senior-level...

  7. Clean Indoor Air in El Paso, Texas: A Case Study

    Directory of Open Access Journals (Sweden)

    Jennifer H. Reynolds, MPH

    2005-01-01

    Full Text Available Background Exposure to secondhand smoke is an important preventable cause of illness and death. A Smoke-Free Paso del Norte Coalition in El Paso, Texas, led a drive to introduce an ordinance to protect nonsmoking persons from the health effects of secondhand smoke in public places. The ordinance was introduced in April 2001 and was passed on June 26, 2001. Context El Paso is the fifth largest city in Texas and the largest border city in the United States. It is the 10th poorest city in the United States; 37% of its residents do not have health insurance. Seventy-eight percent of El Paso’s residents are Hispanic/Latino. A large percentage of El Paso’s restaurant and bar workers are recent immigrants from Mexico. Methods Campaign activities included a letter-writing campaign to the El Paso Times, petition gathering, community outreach education, meetings with city council members, print and television advertising, a proactive media advocacy campaign, and a youth rally. Consequences One month after the ordinance went into effect, an opinion poll found solid support for the new ordinance. Another survey conducted in December 2002 also found a 22% decline in adult smoking, from 22.1% in 1996 to 17.3% at the time of the survey. Interpretation The El Paso campaign is an example of a successful grassroots campaign. El Paso’s campaign relied on direct organizing to identify, recruit, and mobilize supporters, and involved relatively little paid media or paid advocacy efforts. These lessons are transferable to other communities, and the El Paso coalition serves as a model for developing a diverse, representative coalition in a predominantly Mexican American community.

  8. Clean Air Markets - Where You Live (National and State Maps)

    Data.gov (United States)

    U.S. Environmental Protection Agency — Where You Live accesses facility and unit attribute data as well as emissions data using a series of interactive national and state maps. This module allows the user...

  9. Cleaning technics of cleaning robots%清洗机器人的清洗工艺

    Institute of Scientific and Technical Information of China (English)

    何勇强; 周利坤

    2012-01-01

    The cleaning works and cleaning methods of cleaning robots were systematically summarized. The cleaning robots' cleaning technics were illustrated and analyzed. It also specially proposed the idea of oil tank cleaning robot's cleaning technics and process.%对清洗机器人的清洗作业和清洗方法进行了系统分类概述,举例综合分析了清洗机器人的清洗工艺,特别提出了油罐清洗机器人的清洗工艺流程设想。

  10. Application of a Cleaning System Made up of a Centrifugal Fan with Double Channel and One Sieve to Combine

    Institute of Scientific and Technical Information of China (English)

    ShenDechao

    1995-01-01

    In this paper the application of a cleaning system which was made up of a centrifugal fan with double channel and one sieve to 4LZ-3.5 combine was introduced.This cleaning system with double channel compared with the traditional air-sieve cleaning system of combines may omit one two sieves and simplify the transmission mechanism.It is also compared with the present cleaning systom with double channel applied to some combines,such as the Commandor 112CS/228CS combines of Claas Corporation in Germany and the MAXIMIZERTM combines of John Deere company in U.S.A.It may omit one sieve and the precleaner and simlity the transmission mechanism.The measuring results indicated that the cleaning ratio of wheat grain is 99.1% and the cleaning loss ratio of wheat is 0.17% when the feed rate is 4.01kg/s.

  11. Actas. 5. Congreso Internacional del Aire Puro

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    The proceedings of the 5th International Clean Air Congress are presented. Topics covered are: environmental pollutants, their monitoring and interaction with the environment, health effects of pollutants, air pollution control and desulphurization. Papers are in English, French or Spanish. Relevant papers have been abstracted separately.

  12. Nuclear air cleaning handbook. Design, construction, and testing of high-efficiency air cleaning systems for nuclear application

    Energy Technology Data Exchange (ETDEWEB)

    Burchsted, C.A.; Kahn, J.E.; Fuller, A.B.

    1976-01-01

    The handbook is a revision of ORNL/NSIC-65. The purposes of the handbook are to summarize available information in a manner that is useful to the designer, to point out shortcomings in design and construction practice, and to provide guides and recommendations for the design of future systems. (TFD)

  13. Cleaning protocol for a FO membrane fouled in wastewater reuse

    KAUST Repository

    Valladares Linares, Rodrigo

    2013-05-30

    Forward osmosis (FO) is an emerging technology which can be applied in water reuse applications. Osmosis is a natural process that involves less energy consumption than reverse osmosis (RO), and therefore can be applied as a dilution process before low-pressure RO; it is expected to compete favourably against current advanced water reuse technologies that use microfiltration/ultrafiltration and RO. The focus of this research was to assess the efficiency of different cleaning procedures to remove fouling from the surface of a FO membrane during the operation of a submerged system working in FO-mode (active layer (AL) facing feed solution) intended for secondary wastewater effluent (SWWE) recovery, using seawater as draw solution (DS), which will be diluted and can further be fed to a low-pressure RO unit to produce fresh water. Natural organic matter (NOM) fouling was expected to affect the AL, while for the support layer (SL), transparent exopolymer particles (TEP) were used as indicators of fouling due to their stickiness and propensity to enhance the attachment of other foulants in seawater on the membrane surface. The composition of the NOM fouling layer was determined after proper characterisation with a liquid chromatograph coupled with organic carbon detection (LC-OCD), showing biopolymers and protein-like substances as the main constituents. NOM fouling showed high hydraulic reversibility after a 25% flux decline was observed, up to 89.5% when in situ air scouring for 15 min was used as a cleaning technique. Chemical cleaning with a mixture of Alconox, an industrial detergent containing phosphates, and sodium EDTA showed to increase the reversibility (93.6%). Osmotic backwash using a 4% NaCl solution and DI water proved to be ineffective to recover flux due to the salt diffusion phenomena occurring at the AL. Part of the flux that could not be recovered is attributable to TEP fouling on the SL, which forms clusters clearly identifiable with an optical

  14. IDEA Clean Energy Application Center

    Energy Technology Data Exchange (ETDEWEB)

    Thornton, Robert

    2013-09-30

    The DOE Clean Energy Application Centers were launched with a goal of focusing on important aspects of our nation’s energy supply including Efficiency, Reliability and Resiliency. Clean Energy solutions based on Combined Heat & Power (CHP), District Energy and Waste Heat Recovery are at the core of ensuring a reliable and efficient energy infrastructure for campuses, communities, and industry and public enterprises across the country. IDEA members which include colleges and universities, hospitals, airports, downtown utilities as well as manufacturers, suppliers and service providers have long-standing expertise in the planning, design, construction and operations of Clean Energy systems. They represent an established base of successful projects and systems at scale and serve important and critical energy loads. They also offer experience, lessons learned and best practices which are of immense value to the sustained growth of the Clean Energy sector. IDEA has been able to leverage the funds from the project award to raise the visibility, improve the understanding and increase deployment CHP, District Energy and Waste Heat Recovery solutions across the regions of our nation, in collaboration with the regional CEAC’s. On August 30, 2012, President Obama signed an Executive Order to accelerate investments in industrial energy efficiency (EE), including CHP and set a national goal of 40 GW of new CHP installation over the next decade IDEA is pleased to have been able to support this Executive Order in a variety of ways including raising awareness of the goal through educational workshops and Conferences and recognizing the installation of large scale CHP and district energy systems A supporting key area of collaboration has involved IDEA providing technical assistance on District Energy/CHP project screenings and feasibility to the CEAC’s for multi building, multi-use projects. The award was instrumental in the development of a first-order screening

  15. Mechanics ofadhesion and contact self-cleaning of bio-inspired microfiberadhesives

    Science.gov (United States)

    Abusomwan, Uyiosa Anthony

    The remarkable attachment system of geckos has inspired the development of dry microfiber adhesives through the last two decades. Some of the notable characteristics of gecko-inspired fibrillar adhesives include: strong, directional, and controllable adhesion to smooth and rough surfaces in air, vacuum, and under water; ability to maintain strong adhesion during repeated use; anti-fouling and self-cleaning after contamination. Given these outstanding qualities, fibrillar adhesives promise an extensive range of use in industrial, robotic, manufacturing, medical, and consumer products. Significant advancements have been made in the design of geckoinspired microfiber adhesives with the characteristic properties listed above, with the exception of the anti-fouling and self-cleaning features. The self-cleaning mechanism of the gecko's adhesion system plays an important role to its ability to remain sticky in various environments. Similarly, enabling self-cleaning capability for synthetic microfiber adhesives will lead to robust performance in various areas of application. Presently, the practical use of fibrillar adhesives is restricted mainly to clean environments, where they are free from contaminants. The goal of this thesis is to conduct a detailed study of the mechanisms and mechanics of contact-based self-cleaning of gecko-inspired microfiber adhesives. This work focuses on contact self-cleaning mechanisms, as a more practical approach to cleaning. Previous studies on the cleaning of microfiber adhesives have mostly focused on mechanisms that involve complete removal of the contaminants from the adhesive. In this thesis, a second cleaning process is proposed whereby particles are removed from the tip of the microfibers and embedded between adjacent microfibers or in grooves patterned onto the adhesive, where they are no longer detrimental to the performance of the adhesive. In this work, a model of adhesion for microfiber adhesives that take the deformation of the

  16. 78 FR 5140 - Approval and Promulgation of Air Quality Implementation Plans; Colorado; Revisions to New Source...

    Science.gov (United States)

    2013-01-24

    ...., Projected Actual Emissions; II.A.37., Reactivation of Very Clean Coal-fired Electric Utility Steam....45., Small Emissions Unit; II.A.46., Temporary Clean Coal Technology Demonstration Project; XV... consistent with the Clean Air Act (CAA.) This action is being taken under section 110 of the CAA. DATES:...

  17. Innovative Clean Coal Technology (ICCT): 500-MW demonstration of advanced wall-fired cmbustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Field chemical emissions monitoring, Overfire air and overfire air/low NO{sub x} burner operation: Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    This report summarizes data gathered by Radian Corporation at a coal-fired power plant, designated Site 16, for a program sponsored by the United States Department of Energy (DOE), Southern Company Services (SCS), and the Electric Power Research Institute (EPRI). Concentrations of selected inorganic and organic substances were measured in the process and discharge streams of the plant operating under two different types of combustion modifications: overfire air (OFA) and a combination of overfire air with low-NO{sub x} burners (OFA/LNB). Information contained in this report will allow DOE and EPRI to determine the effects of low-NO{sub x} modifications on plant emissions and discharges. Sampling was performed on an opposed wall-fired boiler burning medium-sulfur bituminous coal. Emissions were controlled by electrostatic precipitators (ESPs). The testing was conducted in two distinct sampling periods, with the OFA test performed in March of 1991 and the OFA/LNB test performed in May of 1993. Specific objectives were: to quantify emissions of target substances from the stack; to determine the efficiency of the ESPs for removing the target substances; and to determine the fate of target substances in the various plant discharge streams.

  18. Cleaning insertions and collimation challenges

    CERN Document Server

    Redaelli, S; Bertarelli, A; Bruce, R; Jowett, J M; Lechner, A; Losito, R

    2015-01-01

    High-performance collimation systems are essential for operating efficiently modern hadron machine with large beam intensities. In particular, at the LHC the collimation system ensures a clean disposal of beam halos in the superconducting environment. The challenges of the HL-LHC study pose various demanding requests for beam collimation. In this paper we review the present collimation system and its performance during the LHC Run 1 in 2010–2013. Various collimation solutions under study to address the HL-LHC requirements are then reviewed, identifying the main upgrade baseline and pointing out advanced collimation concept for further enhancement of the performance.

  19. Cleaning Massive Sonar Point Clouds

    DEFF Research Database (Denmark)

    Arge, Lars Allan; Larsen, Kasper Green; Mølhave, Thomas;

    2010-01-01

    We consider the problem of automatically cleaning massive sonar data point clouds, that is, the problem of automatically removing noisy points that for example appear as a result of scans of (shoals of) fish, multiple reflections, scanner self-reflections, refraction in gas bubbles, and so on. We...... describe a new algorithm that avoids the problems of previous local-neighbourhood based algorithms. Our algorithm is theoretically I/O-efficient, that is, it is capable of efficiently processing massive sonar point clouds that do not fit in internal memory but must reside on disk. The algorithm is also...

  20. Clean Water for Developing Countries.

    Science.gov (United States)

    Pandit, Aniruddha B; Kumar, Jyoti Kishen

    2015-01-01

    Availability of safe drinking water, a vital natural resource, is still a distant dream to many around the world, especially in developing countries. Increasing human activity and industrialization have led to a wide range of physical, chemical, and biological pollutants entering water bodies and affecting human lives. Efforts to develop efficient, economical, and technologically sound methods to produce clean water for developing countries have increased worldwide. We focus on solar disinfection, filtration, hybrid filtration methods, treatment of harvested rainwater, herbal water disinfection, and arsenic removal technologies. Simple, yet innovative water treatment devices ranging from use of plant xylem as filters, terafilters, and hand pumps to tippy taps designed indigenously are methods mentioned here. By describing the technical aspects of major water disinfection methods relevant for developing countries on medium to small scales and emphasizing their merits, demerits, economics, and scalability, we highlight the current scenario and pave the way for further research and development and scaling up of these processes. This review focuses on clean drinking water, especially for rural populations in developing countries. It describes various water disinfection techniques that are not only economically viable and energy efficient but also employ simple methodologies that are effective in reducing the physical, chemical, and biological pollutants found in drinking water to acceptable limits.

  1. Clean Coal Program Research Activities

    Energy Technology Data Exchange (ETDEWEB)

    Larry Baxter; Eric Eddings; Thomas Fletcher; Kerry Kelly; JoAnn Lighty; Ronald Pugmire; Adel Sarofim; Geoffrey Silcox; Phillip Smith; Jeremy Thornock; Jost Wendt; Kevin Whitty

    2009-03-31

    Although remarkable progress has been made in developing technologies for the clean and efficient utilization of coal, the biggest challenge in the utilization of coal is still the protection of the environment. Specifically, electric utilities face increasingly stringent restriction on the emissions of NO{sub x} and SO{sub x}, new mercury emission standards, and mounting pressure for the mitigation of CO{sub 2} emissions, an environmental challenge that is greater than any they have previously faced. The Utah Clean Coal Program addressed issues related to innovations for existing power plants including retrofit technologies for carbon capture and sequestration (CCS) or green field plants with CCS. The Program focused on the following areas: simulation, mercury control, oxycoal combustion, gasification, sequestration, chemical looping combustion, materials investigations and student research experiences. The goal of this program was to begin to integrate the experimental and simulation activities and to partner with NETL researchers to integrate the Program's results with those at NETL, using simulation as the vehicle for integration and innovation. The investigators also committed to training students in coal utilization technology tuned to the environmental constraints that we face in the future; to this end the Program supported approximately 12 graduate students toward the completion of their graduate degree in addition to numerous undergraduate students. With the increased importance of coal for energy independence, training of graduate and undergraduate students in the development of new technologies is critical.

  2. Scaleable Clean Aluminum Melting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Han, Q.; Das, S.K. (Secat, Inc.)

    2008-02-15

    The project entitled 'Scaleable Clean Aluminum Melting Systems' was a Cooperative Research and Development Agreements (CRADAs) between Oak Ridge National Laboratory (ORNL) and Secat Inc. The three-year project was initially funded for the first year and was then canceled due to funding cuts at the DOE headquarters. The limited funds allowed the research team to visit industrial sites and investigate the status of using immersion heaters for aluminum melting applications. Primary concepts were proposed on the design of furnaces using immersion heaters for melting. The proposed project can continue if the funding agency resumes the funds to this research. The objective of this project was to develop and demonstrate integrated, retrofitable technologies for clean melting systems for aluminum in both the Metal Casting and integrated aluminum processing industries. The scope focused on immersion heating coupled with metal circulation systems that provide significant opportunity for energy savings as well as reduction of melt loss in the form of dross. The project aimed at the development and integration of technologies that would enable significant reduction in the energy consumption and environmental impacts of melting aluminum through substitution of immersion heating for the conventional radiant burner methods used in reverberatory furnaces. Specifically, the program would couple heater improvements with furnace modeling that would enable cost-effective retrofits to a range of existing furnace sizes, reducing the economic barrier to application.

  3. Research and development of Ro-boat: an autonomous river cleaning robot

    Science.gov (United States)

    Sinha, Aakash; Bhardwaj, Prashant; Vaibhav, Bipul; Mohommad, Noor

    2013-12-01

    Ro-Boat is an autonomous river cleaning intelligent robot incorporating mechanical design and computer vision algorithm to achieve autonomous river cleaning and provide a sustainable environment. Ro-boat is designed in a modular fashion with design details such as mechanical structural design, hydrodynamic design and vibrational analysis. It is incorporated with a stable mechanical system with air and water propulsion, robotic arms and solar energy source and it is proceed to become autonomous by using computer vision. Both "HSV Color Space" and "SURF" are proposed to use for measurements in Kalman Filter resulting in extremely robust pollutant tracking. The system has been tested with successful results in the Yamuna River in New Delhi. We foresee that a system of Ro-boats working autonomously 24x7 can clean a major river in a city on about six months time, which is unmatched by alternative methods of river cleaning.

  4. Clean energy development is a win-win-win for jobs, economic growth and the environment

    Energy Technology Data Exchange (ETDEWEB)

    Learner, H.A. [Environmental Law and Policy Center, IL (United States)

    2003-07-01

    The Environmental Law and Policy Center of Illinois has recently released several publications promoting clean energy development to improve environmental quality and public health for the Midwest. This presentation emphasized how the clean energy development plan can create new jobs and stimulate economic growth. For example, the electric power industry is currently relying on 1950's energy technology. Modernizing the electricity industry would be good for both the economy and the environment. Repowering the industry would promote energy efficiency and renewable energy sources. The presentation also compared a business-as-usual (BAU) scenario and a clean energy development plan scenario for 2010 and 2020. It was suggested that policy changes may be required to ensure change. In the BAU scenario, electricity demand would increase annually, large additions of natural gas capacity would be used to meet the demand, and coal plants would increase their output. Under the clean energy development plan, electricity demand would flatten out, coal and nuclear plants would be replaced with renewables (mostly wind) or clean, natural gas generation. Under the clean energy development plan NOx would be reduced by 71 per cent, SOx by 56 per cent, mercury by 50 per cent, and carbon dioxide by 51 per cent. The clean energy development plan improves the environment by reducing air and water pollution and improves electricity reliability. 8 tabs., 20 figs.

  5. National Clean Fleets Partnership (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2012-01-01

    Provides an overview of Clean Cities National Clean Fleets Partnership (NCFP). The NCFP is open to large private-sector companies that have fleet operations in multiple states. Companies that join the partnership receive customized assistance to reduce petroleum use through increased efficiency and use of alternative fuels. This initiative provides fleets with specialized resources, expertise, and support to successfully incorporate alternative fuels and fuel-saving measures into their operations. The National Clean Fleets Partnership builds on the established success of DOE's Clean Cities program, which reduces petroleum consumption at the community level through a nationwide network of coalitions that work with local stakeholders. Developed with input from fleet managers, industry representatives, and Clean Cities coordinators, the National Clean Fleets Partnership goes one step further by working with large private-sector fleets.

  6. 40 CFR 52.144 - Significant deterioration of air quality.

    Science.gov (United States)

    2010-07-01

    ... quality. 52.144 Section 52.144 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... deterioration of air quality. (a) The requirements of sections 160 through 165 of the Clean Act are not met... lands does not include approvable procedures for preventing the significant deterioration of air...

  7. An automated cleaning system for hospitals

    OpenAIRE

    Griffin, Colin

    2009-01-01

    Insufficient hygienic practices in Irish hospitals coupled with one of the highest number of reported cases of MRSA in Europe have highlighted the need for solutions to aid in the task of cleaning. This automated cleaning system consisted of two robots: a core robot developed separately with navigational and task scheduling capabilities integrated. The cleaning task was carried out by making use of a commercially available Roomba vacuum cleaner which had been adapted to operate in conju...

  8. National Clean Fleets Partnership (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-01-01

    Clean Cities' National Clean Fleets Partnership establishes strategic alliances with large fleets to help them explore and adopt alternative fuels and fuel economy measures to cut petroleum use. The initiative leverages the strength of nearly 100 Clean Cities coalitions, nearly 18,000 stakeholders, and more than 20 years of experience. It provides fleets with top-level support, technical assistance, robust tools and resources, and public acknowledgement to help meet and celebrate fleets' petroleum-use reductions.

  9. Cleaning of Livefront Electrical Switchgear Using Carbon Dioxide Pellets at Navy Installations

    Science.gov (United States)

    1998-05-01

    revoluciones automätico centrifugo - Bloque presofundido en aluminio - Cilindro en fundiciön perlitica - Filtro de aire en seco (en bafio de aceite con...gate. Pedestrians - minimum of 15 ft. From the switch and 5 ft. from the service truck. 3. Housekeeping Pad cleaning Vegetation 4. Outage required

  10. Clean Cities Annual Metrics Report 2006

    Energy Technology Data Exchange (ETDEWEB)

    Bergeron, P.; Putsche, V.

    2007-07-01

    Report summarizes Clean Cities coalition accomplishments, including membership, funding, sales of alternative fuel blends, deployment of AFVs and HEVs, idle reduction initiatives, and fuel economy activities.

  11. Air Pollution

    Science.gov (United States)

    Air pollution is a mixture of solid particles and gases in the air. Car emissions, chemicals from factories, dust, ... a gas, is a major part of air pollution in cities. When ozone forms air pollution, it's ...

  12. Unit for cleaning drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Dorosh, M.M.; Dera, Ya.I.; Fesenko, M.M.; Makedonov, N.I.; Surkov, V.T.

    1983-01-01

    A design is proposed for a unit for cleaning drilling muds which includes a settling tank with input sleeve and a sleeve of the purified mud and hydrocyclones. In order to improve the effectiveness of the degree of purification, the unit is equipped with an ejector and sludge filter arranged under the settling tank in the form of a grid installed in the upper part of the settling tank and connected to the sleeve of purified mud, while the inlet sleeve is arranged tangentially. The proposed unit can operate during drilling with the use of muds on water and carbon bases. As a result of its use, the degree of purification of the drilling mud reaches 30-35%; there is an increase in mechanical drilling rate, the service life of the sand-separator and the silt separators and decrease in wear of the pump equipment.

  13. Beam Cleaning and Collimation Systems

    CERN Document Server

    Redaelli, S

    2016-01-01

    Collimation systems in particle accelerators are designed to dispose of unavoidable losses safely and efficiently during beam operation. Different roles are required for different types of accelerator. The present state of the art in beam collimation is exemplified in high-intensity, high-energy superconducting hadron colliders, like the CERN Large Hadron Collider (LHC), where stored beam energies reach levels up to several orders of magnitude higher than the tiny energies required to quench cold magnets. Collimation systems are essential systems for the daily operation of these modern machines. In this document, the design of a multistage collimation system is reviewed, taking the LHC as an example case study. In this case, unprecedented cleaning performance has been achieved, together with a system complexity comparable to no other accelerator. Aspects related to collimator design and operational challenges of large collimation systems are also addressed.

  14. Carbon nanotubes – becoming clean

    Directory of Open Access Journals (Sweden)

    Nicole Grobert

    2007-01-01

    Full Text Available Carbon nanotubes (CNTs are now well into their teenage years. Early on, theoretical predictions and experimental data showed that CNTs possess chemical and mechanical properties that exceed those of many other materials. This has triggered intense research into CNTs. A variety of production methods for CNTs have been developed; chemical modification, functionalization, filling, and doping have been achieved; and manipulation, separation, and characterization of individual CNTs is now possible. Today, products containing CNTs range from tennis rackets and golf clubs to vehicle fenders, X-ray tubes, and Li ion batteries. Breakthroughs for CNT-based technologies are anticipated in the areas of nanoelectronics, biotechnology, and materials science. In this article, I review the current situation in CNT production and highlight the importance of clean CNT material for the success of future applications.

  15. Cleaning lady saves the day

    CERN Multimedia

    2009-01-01

    At lunch time on Wednesday 21 January a guest at the CERN hostel put her food in the microwave oven and switched it on. "Within seconds I smelt plastic. I looked into the oven and saw flames. I switched it off, took my food out. But the flames continued and so I ran for the door." In the corridor she ran into Jane Kiranga, a cleaning lady working for the company ISS. Without hesitation Jane picked up a portable fire extinguisher, returned to the kitchen and stopped the fire. The Fire Brigade arrived a few minutes later and only needed to ventilate the kitchen. "Jane was just in time, because the flames had not left the oven yet. Her model behaviour deserves recognition," said the team leader on duty for the CERN Fire Brigade. A few days later Jane received a gift voucher from the Prevention and Training section of the Safety Commission (photo).

  16. Supercritical CO2 Cleaning System for Planetary Protection and Contamination Control Applications

    Science.gov (United States)

    Lin, Ying; Zhong, Fang; Aveline, David C.; Anderson, Mark S.

    2012-01-01

    Current spacecraft-compatible cleaning protocols involve a vapor degreaser, liquid sonication, and alcohol wiping. These methods are not very effective in removing live and dead microbes from spacecraft piece parts of slightly complicated geometry, such as tubing and loosely fitted nuts and bolts. Contamination control practices are traditionally focused on cleaning and monitoring of particulate and oily residual. Vapor degreaser and outgassing bakeout have not been proven to be effective in removing some less volatile, hydrophilic biomolecules of significant relevance to life detection. A precision cleaning technology was developed using supercritical CO2 (SCC). SCC is used as both solvent and carrier for removing organic and particulate contaminants. Supercritical fluid, like SCC, is characterized by physical and thermal properties that are between those of the pure liquid and gas phases. The fluid density is a function of the temperature and pressure. Its solvating power can be adjusted by changing the pressure or temperature, or adding a secondary solvent such as alcohol or water. Unlike a regular organic solvent, SCC has higher diffusivities, lower viscosity, and lower surface tension. It readily penetrates porous and fibrous solids and can reach hard-to-reach surfaces of the parts with complex geometry. Importantly, the CO2 solvent does not leave any residue. The results using this new cleaning device demonstrated that both supercritical CO2 with 5% water as a co-solvent can achieve cleanliness levels of 0.01 mg/cm2 or less for contaminants of a wide range of hydrophobicities. Experiments under the same conditions using compressed Martian air mix, which consists of 95% CO2, produced similar cleaning effectiveness on the hydrophobic compounds. The main components of the SCC cleaning system are a high-pressure cleaning vessel, a boil-off vessel located downstream from the cleaning vessel, a syringe-type high-pressure pump, a heat exchanger, and a back pressure

  17. The NOXSO clean coal project

    Energy Technology Data Exchange (ETDEWEB)

    Black, J.B.; Woods, M.C.; Friedrich, J.J.; Browning, J.P. [NOXSO Corp., Bethel Park, PA (United States)

    1997-12-31

    The NOXSO Clean Coal Project will consist of designing, constructing, and operating a commercial-scale flue-gas cleanup system utilizing the NOXSO Process. The process is a waste-free, dry, post-combustion flue-gas treatment technology which uses a regenerable sorbent to simultaneously adsorb sulfur dioxide (SO{sub 2}) and nitrogen oxides (NO{sub x}) from flue gas from coal-fired boilers. The NOXSO plant will be constructed at Alcoa Generating Corporation`s (AGC) Warrick Power Plant near Evansville, Indiana and will treat all the flue gas from the 150-MW Unit 2 boiler. The NOXSO plant is being designed to remove 98% of the SO{sub 2} and 75% of the NO{sub x} when the boiler is fired with 3.4 weight percent sulfur, southern-Indiana coal. The NOXSO plant by-product will be elemental sulfur. The elemental sulfur will be shipped to Olin Corporation`s Charleston, Tennessee facility for additional processing. As part of the project, a liquid SO{sub 2} plant has been constructed at this facility to convert the sulfur into liquid SO{sub 2}. The project utilizes a unique burn-in-oxygen process in which the elemental sulfur is oxidized to SO{sub 2} in a stream of compressed oxygen. The SO{sub 2} vapor will then be cooled and condensed. The burn-in-oxygen process is simpler and more environmentally friendly than conventional technologies. The liquid SO{sub 2} plant produces 99.99% pure SO{sub 2} for use at Olin`s facilities. The $82.8 million project is co-funded by the US Department of Energy (DOE) under Round III of the Clean Coal Technology program. The DOE manages the project through the Pittsburgh Energy Technology Center (PETC).

  18. 78 FR 37 - Approval and Promulgation of Air Quality Implementation Plans; Utah; Maintenance Plan for the...

    Science.gov (United States)

    2013-01-02

    ... Vapor Recovery Systems for Gasoline Delivery Tanks.'' This action is being taken under sections 107 and 110 of the Clean Air Act (Act). DATES: Comments must be received on or before February 1, 2013... or CAA mean or refer to the Clean Air Act, unless the context indicates otherwise. (ii) The words...

  19. 78 FR 59242 - Approval and Promulgation of Air Quality Implementation Plans; Utah; Maintenance Plan for the...

    Science.gov (United States)

    2013-09-26

    ... Vapor Recovery Systems for Gasoline Delivery Tanks.'' This action is being taken under sections 107 and 110 of the Clean Air Act (Act or CAA). DATES: This action is effective on October 28, 2013. ADDRESSES... follows: (i) The words or initials Act or CAA mean or refer to the Clean Air Act, unless the...

  20. 75 FR 13468 - Disapproval of California State Implementation Plan Revisions, Monterey Bay Unified Air Pollution...

    Science.gov (United States)

    2010-03-22

    ... version of Rule 400 into the SIP. Please see 70 FR 46770. CARB has not submitted a subsequent version of... Implementation of Title I of the Clean Air Act Amendments of 1990,'' 57 FR 13498 (April 16, 1992); 57 FR 18070... Implementation of Title I of the Clean Air Act Amendments of 1990,'' 59 FR 41998 (August 16, 1994). 5....

  1. CleanFleet. Final report: Volume 7, vehicle emissions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    Measurements of exhaust and evaporative emissions from Clean Fleet vans running on M-85, compressed natural gas (CNG), California Phase 2 reformulated gasoline (RFG), propane gas, and a control gasoline (RF-A) are presented. Three vans from each combination of vehicle manufacturer and fuel were tested at the California Air Resources Board (ARB) as they accumulated mileage in the demonstration. Data are presented on regulated emissions, ozone precursors, air toxics, and greenhouse gases. The emissions tests provide information on in-use emissions. That is, the vans were taken directly from daily commercial service and tested at the ARB. The differences in alternative fuel technology provide the basis for a range of technology options. The emissions data reflect these differences, with classes of vehicle/fuels producing either more or less emissions for various compounds relative to the control gasoline.

  2. Timing calibration and spectral cleaning of LOFAR time series data

    CERN Document Server

    Corstanje, A; Enriquez, J E; Falcke, H; Hörandel, J R; Krause, M; Nelles, A; Rachen, J P; Schellart, P; Scholten, O; ter Veen, S; Thoudam, S; Trinh, T N G

    2016-01-01

    We describe a method for spectral cleaning and timing calibration of short voltage time series data from individual radio interferometer receivers. It makes use of the phase differences in Fast Fourier Transform (FFT) spectra across antenna pairs. For strong, localized terrestrial sources these are stable over time, while being approximately uniform-random for a sum over many sources or for noise. Using only milliseconds-long datasets, the method finds the strongest interfering transmitters, a first-order solution for relative timing calibrations, and faulty data channels. No knowledge of gain response or quiescent noise levels of the receivers is required. With relatively small data volumes, this approach is suitable for use in an online system monitoring setup for interferometric arrays. We have applied the method to our cosmic-ray data collection, a collection of measurements of short pulses from extensive air showers, recorded by the LOFAR radio telescope. Per air shower, we have collected 2 ms of raw tim...

  3. ActiveClean: Interactive Data Cleaning While Learning Convex Loss Models

    OpenAIRE

    2016-01-01

    Data cleaning is often an important step to ensure that predictive models, such as regression and classification, are not affected by systematic errors such as inconsistent, out-of-date, or outlier data. Identifying dirty data is often a manual and iterative process, and can be challenging on large datasets. However, many data cleaning workflows can introduce subtle biases into the training processes due to violation of independence assumptions. We propose ActiveClean, a progressive cleaning ...

  4. Microbial water quality in clean water tanks following inspection and cleaning

    OpenAIRE

    Christensen, Sarah Christine Boesgaard; Esbjørn, Anne; Albrechtsen, Hans-Jørgen

    2014-01-01

    Increased bacterial counts are often registered in drinking water leaving clean water tanks after the tanks have been emptied, inspected and cleaned by flushing. To investigate the reason for the increased bacterial concentrations and consequently limit it, samples from two clean water tanks before, during and after cleaning of the tanks were analysed. Bacteria were quantified, the dominating bacterial groups were identified and re-growth potential in the water was estimated. Bacterial counts...

  5. Rudimentary Cleaning Compared to Level 300A

    Science.gov (United States)

    Arpin, Christina Y. Pina; Stoltzfus, Joel

    2012-01-01

    A study was done to characterize the cleanliness level achievable when using a rudimentary cleaning process, and results were compared to JPR 5322.1G Level 300A. While it is not ideal to clean in a shop environment, some situations (e.g., field combat operations) require oxygen system hardware to be maintained and cleaned to prevent a fire hazard, even though it cannot be sent back to a precision cleaning facility. This study measured the effectiveness of basic shop cleaning. Initially, three items representing parts of an oxygen system were contaminated: a metal plate, valve body, and metal oxygen bottle. The contaminants chosen were those most likely to be introduced to the system during normal use: oil, lubricant, metal shavings/powder, sand, fingerprints, tape, lip balm, and hand lotion. The cleaning process used hot water, soap, various brushes, gaseous nitrogen, water nozzle, plastic trays, scouring pads, and a controlled shop environment. Test subjects were classified into three groups: technical professionals having an appreciation for oxygen hazards; professional precision cleaners; and a group with no previous professional knowledge of oxygen or precision cleaning. Three test subjects were in each group, and each was provided with standard cleaning equipment, a cleaning procedure, and one of each of the three test items to clean. The results indicated that the achievable cleanliness level was independent of the technical knowledge or proficiency of the personnel cleaning the items. Results also showed that achieving a Level 300 particle count was more difficult than achieving a Level A nonvolatile residue amount.

  6. Equivalent cleaning in a juvenile facultative and obligate cleaning wrasse: an insight into the evolution of cleaning in labrids?

    Science.gov (United States)

    Grutter, Alexandra S.; Feeney, William E.

    2016-09-01

    Species that exhibit ontogenetic variation in interspecific cleaning behaviours may offer insights into how interspecific cooperation evolves. We investigated the foraging ecology of the yellowtail tubelip wrasse ( Diproctacanthus xanthurus), a facultative cleaner as a juvenile and corallivore as an adult, and compared its juvenile ecology with that of juvenile blue-streak cleaner wrasse ( Labroides dimidiatus), a closely related and sympatric obligate cleaner. While juveniles of the two species differed in the amount of time they inspected clients, the number of client individuals and species that were cleaned and the proportion that posed did not differ, nor did the number of ectoparasitic isopods in their guts. In contrast, adult yellowtail tubelip wrasse had fewer isopods and more coral mucus in their guts than juveniles. These data support a hypothesized series of events in which juvenile cleaning acts as an evolutionary precursor to obligate cleaning and suggest that the yellowtail tubelip wrasse may present an intermediate between corallivory and cleaning.

  7. How Do We Clean Our Water and How Clean Does It Need to Be?

    Science.gov (United States)

    Whitburn, Niki

    2013-01-01

    Nowadays, in the United Kingdom, citizens take for granted clean water pumped directly into their homes, but it was not always the case, and is still not so in many countries. Could people clean water themselves if they had to and what could they then use it for? Would it actually be "clean enough" to drink? The author presents children…

  8. Cleaning-resistant Cupriavidus and Ralstonia bacteria contaminating spacecrafts and the ultra clean rooms they are assembled in.

    Science.gov (United States)

    Leys, N.; Dams, A.; Bossus, A.; Provoost, A.; Venkateswaran, K.; Mergeay, M.

    Background Planetary Protection is preventing microbial contamination of both the target planet and the Earth when sending spacecrafts on interplanetary space mission It is important to preserve the natural conditions of other planets and to not bring with robots earthly microbes forward contamination when looking for spores of extra terrestrial life Spacecrafts and the ultra clean rooms they are assembled in are routinely monitored for microbial contamination It was shown that the floor air and surfaces of such spacecraft assembly rooms often contain Cupriavidu s and Ralstonia bacteria These bacteria not only contaminated the clean rooms but have also been found prior-to-flight on surfaces of space robots such as the Mars Odyssey Orbiter La Duc et al 2003 and even in-flight in ISS cooling water and Shuttle drinking water unpublished Aim In this study several Cupriavidus and Ralstonia strains isolated from space craft assembling rooms and spacecrafts were characterized and analysed in detail Results The analysis showed that all the Cupriavidus and Ralstonia clean-room isolates are able to use a wide variety of substrates as carbon sources including ethanol and acetone In addition they all have accumulated moderate resistances to an extraordinary collection of physical and chemical antimicrobial agents Some of the test strains were able to form biofilms on plastic and metal materials used for space robots a nutritional and

  9. Decontamination of Genesis Array Materials by UV Ozone Cleaning

    Science.gov (United States)

    Calaway, Michael J.; Burnett, D. S.; Rodriquez, M. C.; Sestak, S.; Allton, J. H.; Stansbery, E. K.

    2007-01-01

    Shortly after the NASA Genesis Mission sample return capsule returned to earth on September 8, 2004, the science team discovered that all nine ultra-pure semiconductor materials were contaminated with a thin molecular organic film approximately 0 to 100 angstroms thick. The organic contaminate layer, possibly a silicone, situated on the surface of the materials is speculated to have formed by condensation of organic matter from spacecraft off-gassing at the Lagrange 1 halo orbit during times of solar exposure. While the valuable solar wind atoms are safely secured directly below this organic contamination and/or native oxide layer in approximately the first 1000 angstroms of the ultra-pure material substrate, some analytical techniques that precisely measure solar wind elemental abundances require the removal of this organic contaminate. In 2005, Genesis science team laboratories began to develop various methods for removing the organic thin film without removing the precious material substrate that contained the solar wind atoms. Stephen Sestak and colleagues at Open University first experimented with ultraviolet radiation ozone (UV/O3) cleaning of several non-flight and flown Genesis silicon wafer fragments under a pure flowing oxygen environment. The UV/O3 technique was able to successfully remove organic contamination without etching into the bulk material substrate. At NASA Johnson Space Center Genesis Curation Laboratory, we have installed an UV/O3 cleaning devise in an ambient air environment to further experimentally test the removal of the organic contamination on Genesis wafer materials. Preliminary results from XPS analysis show that the UV/O3 cleaning instrument is a good non-destructive method for removing carbon contamination from flown Genesis array samples. However, spectroscopic ellipsometry results show little change in the thickness of the surface film. All experiments to date have shown UV/O3 cleaning method to be the best non-destructive method

  10. Advanced Methods for Air Distribution in Occupied Spaces for Reduced Risk from Air-Borne Diseases and Improved Air Quality

    DEFF Research Database (Denmark)

    Bolashikov, Zhecho Dimitrov

    The current Ph.D. thesis deals with new advanced methods of air distribution in occupied places aimed to improve the inhaled air quality and to reduce the risk from airborne cross infection among the occupants. The existing ventilation strategies nowadays are not able to provide enough clean air...... pathogens. The threat from possible bio-terrorist attacks in the last decade makes the topic quite important. So far the existing methods of indoor air cleaning rely on several basic strategies: dilution, filtration and Ultra Violet Germicidal Irradiation (UVGI). Dilution utilizes ventilation at high flow...... rates to reduce the concentration of pollutants/pathogens to levels that would not deteriorate the air quality or be harmful for the occupants. It is also connected to certain energy limitation issues. Filtration and UVGI are efficient in protecting occupants provided the sources are located outdoors...

  11. Quantitative assessment of airborne exposures generated during common cleaning tasks: a pilot study

    Directory of Open Access Journals (Sweden)

    Perry Melissa J

    2010-11-01

    Full Text Available Abstract Background A growing body of epidemiologic evidence suggests an association between exposure to cleaning products with asthma and other respiratory disorders. Thus far, these studies have conducted only limited quantitative exposure assessments. Exposures from cleaning products are difficult to measure because they are complex mixtures of chemicals with a range of physicochemical properties, thus requiring multiple measurement techniques. We conducted a pilot exposure assessment study to identify methods for assessing short term, task-based airborne exposures and to quantitatively evaluate airborne exposures associated with cleaning tasks simulated under controlled work environment conditions. Methods Sink, mirror, and toilet bowl cleaning tasks were simulated in a large ventilated bathroom and a small unventilated bathroom using a general purpose, a glass, and a bathroom cleaner. All tasks were performed for 10 minutes. Airborne total volatile organic compounds (TVOC generated during the tasks were measured using a direct reading instrument (DRI with a photo ionization detector. Volatile organic ingredients of the cleaning mixtures were assessed utilizing an integrated sampling and analytic method, EPA TO-17. Ammonia air concentrations were also measured with an electrochemical sensor embedded in the DRI. Results Average TVOC concentrations calculated for 10 minute tasks ranged 0.02 - 6.49 ppm and the highest peak concentrations observed ranged 0.14-11 ppm. TVOC time concentration profiles indicated that exposures above background level remained present for about 20 minutes after cessation of the tasks. Among several targeted VOC compounds from cleaning mixtures, only 2-BE was detectable with the EPA method. The ten minute average 2- BE concentrations ranged 0.30 -21 ppm between tasks. The DRI underestimated 2-BE exposures compared to the results from the integrated method. The highest concentration of ammonia of 2.8 ppm occurred

  12. Clean Coal Technologies - Accelerating Commerical and Policy Drivers for Deployment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Coal is and will remain the world's most abundant and widely distributed fossil fuel. Burning coal, however, can pollute and it produces carbon dioxide. Clean coal technologies address this problem. The widespread deployment of pollution-control equipment to reduce sulphur dioxide, Nox and dust emissions from industry is just one example which has brought cleaner air to many countries. Since the 1970s, various policy and regulatory measures have created a growing commercial market for these clean coal technologies, with the result that costs have fallen and performance has improved. More recently, the need to tackle rising CO2 emissions to address climate change means that clean coal technologies now extend to include those for CO2 capture and storage (CCS). This short report from the IEA Coal Industry Advisory Board (CIAB) presents industry's considered recommendations on how to accelerate the development and deployment of this important group of new technologies and to grasp their very signifi cant potential to reduce emissions from coal use. It identifies an urgent need to make progress with demonstration projects and prove the potential of CCS through government-industry partnerships. Its commercialisation depends upon a clear legal and regulatory framework,public acceptance and market-based financial incentives. For the latter, the CIAB favours cap-and-trade systems, price supports and mandatory feed-in tariffs, as well as inclusion of CCS in the Kyoto Protocol's Clean Development Mechanism to create demand in developing economies where coal use is growing most rapidly. This report offers a unique insight into the thinking of an industry that recognises both the threats and growing opportunities for coal in a carbon constrained world.

  13. Clean Cities Now Vol. 19, No. 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-12-18

    Clean Cities Now is the official bi-annual newsletter of Clean Cities, an initiative designed to reduce petroleum consumption in the transportation sector by advancing the use of alternative and renewable fuels, fuel economy improvements, idle-reduction measures, and new technologies, as they emerge.

  14. Gas turbine cleaning upgrade (compressor wash)

    Energy Technology Data Exchange (ETDEWEB)

    Asplund, P. [Gas Turbine Efficiency, Jarfalla (Sweden)

    1998-12-31

    The influence of gas turbine degradation on operating costs is high. Gas turbine cleaning is one of many actions taken for power recovery and is to consider as preventive maintenance. It is generally performed within the industrial field and occasionally within the aero sector. In order to meet the gas turbine development win high blade loads and ever-increasing temperatures, together with emission Aces and environmental regulations, more efficient and careful cleaning methods are needed. Following a survey about potentials for cost reduction in gas turbine operation a new man-hour and water saving cleaning method has been evaluated for a standard process. Compared with traditional cleaning methods, the new method is water,- cost,- weight and space saving due to a new washing technique. Traditional methods are based on using different nozzles for ON and OFF-line cleaning, which rise the demand for complicated systems. In the new method the same nozzle installation, same liquid flow and pressure is used for both ON and OFF-line cleaning. This gives a cost reduction of appr. 20.000 - 30.000 USD per gas turbine depending on installation and size. Evaluation of the new method shows significantly improved ON -line cleaning performance and thus OFF -line cleaning is required only during scheduled stops. (orig.) 10 refs.

  15. Clean Cities Now Vol. 20, No. 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-13

    Clean Cities Now is the official semi-annual newsletter of Clean Cities, an initiative designed to reduce petroleum consumption in the transportation sector by advancing the use of alternative and renewable fuels, fuel economy improvements, idle-reduction measures, and new technologies, as they emerge.

  16. Cathodic ARC surface cleaning prior to brazing

    Energy Technology Data Exchange (ETDEWEB)

    Dave, V. R. (Vivek R.); Hollis, K. J. (Kendall J.); Castro, R. G. (Richard G.); Smith, F. M. (Frank M.); Javernick, D. A. (Daniel A.)

    2002-01-01

    Surface cleanliness is one the critical process variables in vacuum furnace brazing operations. For a large number of metallic components, cleaning is usually accomplished either by water-based alkali cleaning, but may also involve acid etching or solvent cleaning / rinsing. Nickel plating may also be necessary to ensure proper wetting. All of these cleaning or plating technologies have associated waste disposal issues, and this article explores an alternative cleaning process that generates minimal waste. Cathodic arc, or reserve polarity, is well known for welding of materials with tenacious oxide layers such as aluminum alloys. In this work the reverse polarity effect is used to clean austenitic stainless steel substrates prior to brazing with Ag-28%Cu. This cleaning process is compared to acid pickling and is shown to produce similar wetting behavior as measured by dynamic contact angle experiments. Additionally, dynamic contact angle measurements with water drops are conducted to show that cathodic arc cleaning can remove organic contaminants as well. The process does have its limitations however, and alloys with high titanium and aluminum content such as nickel-based superalloys may still require plating to ensure adequate wetting.

  17. A multistep approach for reticle cleaning

    NARCIS (Netherlands)

    Koster, N.B.; Donck, J.C.J. van der; Stortelder, J.K.; Jong, A.J. de; Molkenboer, F.T.

    2012-01-01

    The introduction of EUV Lithography for the next node has two major obstacles at the moment; the first is source power and reliability and the second is defect free reticles and damage free cleaning of reticles. We present our results on our investigation for damage free cleaning of EUV reticles wit

  18. Clean Cities Now Vol. 17, No. 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-10-23

    The Fall 2013 issue of the biannual newsletter for the U.S. Department of Energy's Clean Cities initiative. The newsletter includes feature stories on deployment of alternative fuels and advanced vehicles, and articles on Clean Cities coalition successes across the country.

  19. Clean Cities Now, Vol. 18, No. 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-04-30

    The Spring 2014 edition of the semi-annual newsletter for the U.S. Department of Energy's Clean Cities initiative. The newsletter includes feature stories on deployment of alternative fuels and advanced vehicles, and articles on Clean Cities coalition successes across the country.

  20. Clean Cities Now Vol. 20, No. 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-01-13

    Clean Cities Now is the official semi-annual newsletter of Clean Cities, an initiative designed to reduce petroleum consumption in the transportation sector by advancing the use of alternative and renewable fuels, fuel economy improvements, idle-reduction measures, and new technologies, as they emerge.