Preparation and characterization of Bi26-2xMn2xMo10O69-d and Bi26.4Mn0.6Mo10-2yMe2yO69-d (Me = V, Fe Solid Solutions

Directory of Open Access Journals (Sweden)

Z. A. Mikhaylovskaya

2017-09-01

Full Text Available Single phase samples of bismuth molybdate, Bi26Mo10O69, doped with Mn on the bismuth sublattice and V, Fe on the molybdenum sublattice were found to crystallize in the triclinic Bi26Mo10O69 structure at low doping levels and in the monoclinic Bi26Mo10O69 structure - at higher dopant concentration. The assumption that all Mn ions have an oxidation state of +2 was confirmed by means of magnetic measurement results analysis using Curie-Weiss law. Conductivity was investigated using impedance spectroscopy. The conductivity of Bi26.4Mn0.6Mo9.6Fe0.4O69-d was 1.2*10-2 S*cm-1 at 973 K and 2.2*10-4 S*cm-1 at 623 K, and the conductivity of Bi26.4Mn0.6Mo9.2V0.8O69-d was 2.2*10-3 S*cm-1 at 973 K and 2.2*10-5 S*cm-1 at 623 K.

Structural and optical investigation in Er3+ doped Y2MoO6 phosphors

Science.gov (United States)

Mondal, Manisha; Rai, Vineet Kumar

2018-05-01

The Er3+ doped Y2MoO6 phosphors have been structurally and optically characterized by X-ray Diffraction (XRD), Field emission scanning electron microscopy (FESEM), UV-Vis absorption spectroscopy and frequency upconversion (UC) emission studies. The crystal and the particles size are found to be ˜ 85 nm and ˜ 200 nm from XRD and FESEM analysis. The intense peak at ˜ 206 nm in the UV-Vis absorption spectroscopy is attributed due to the charge transfer transition between the Mo6+ and the O2- ions in the MoO4 group in the host molybdate. The frequency UC emission studies of the prepared phosphors under 980 nm diode laser excitation shows the intense UC emission in the 0.3 mol% concentrations for the Er3+ ions. In the UC emission spectra, the emission peaks at green (˜ 525 nm and ˜ 546 nm) and red (˜ 656 nm) bands are corresponding to the 2H11/2, 4S3/2 → 4I15/2 and 4F9/2 → 4I15/2 transitions of Er3+ ions. The mechanisms involved in the UC process have been explored with the help of energy level diagram. Moreover, the CIE point (0.31, 0.60) lie in the green colour region which indicates that the developed phosphor have suitable applications in NIR to visible upconverter and in making green light display devices.

Unified inelastic constitutive equations incorporating dynamic strain aging for Mod. 9Cr-1Mo steel

International Nuclear Information System (INIS)

Yaguchi, Masatsugu; Takahashi, Yukio

1998-01-01

A unified constitutive model considering dynamic strain aging effect was developed in order to describe inelastic deformation behavior of the Mod. 9Cr-1Mo steel precisely. The inelastic behavior of the steel was summarized as follows. A rate dependent deformation was observed above 500degC, and there was no rate dependency under 400degC. However, stress relaxation behavior was observed even at rate independent temperature region. Further, a stress after relaxation depended on prior loading strain rate, and it showed a higher value as the strain rate was slow. A feature of the proposed constitutive model was that an applied stress consists of three stress components: a back stress, an overstress and an aging stress which corresponds to dynamics strain aging and shows a negative strain rate dependency. The aging stress was measured by strain rate change tests, and it showed larger values as the strain rates were slow and the temperatures were low. The backstress and the overstress were measured by strain dip tests. The backstress was approximately rate independent under 400degC, however it showed rate dependency above 500degC. The overstress showed larger values as the strain rates were fast and the temperatures were high. The material constants were determined systematically based on the measured values of each internal variable. In order to evaluate the validity of the constitutive model, numerical simulations were done for various inelastic deformation behavior of Mod. 9Cr-1Mo steel. The simulations agreed with experimental results very well in all cases. (author)

Observation of Vacancies, Faults, and Superstructures in Ln5Mo2O12 (Ln = La, Y, and Lu) Compounds with Direct Mo-Mo Bonding.

Science.gov (United States)

Colabello, Diane M; Sobalvarro, Elizabeth M; Sheckelton, John P; Neuefeind, Joerg C; McQueen, Tyrel M; Khalifah, Peter G

2017-11-06

Among oxide compounds with direct metal-metal bonding, the Y 5 Mo 2 O 12 (A 5 B 2 O 12 ) structural family of compounds has a particularly intriguing low-dimensional structure due to the presence of bioctahedral B 2 O 10 dimers arranged in one-dimensional edge-sharing chains along the direction of the metal-metal bonds. Furthermore, these compounds can have a local magnetic moment due to the noninteger oxidation state (+4.5) of the transition metal, in contrast to the conspicuous lack of a local moment that is commonly observed when oxide compounds with direct metal-metal bonding have integer oxidation states resulting from the lifting of orbital degeneracy typically induced by the metal-metal bonding. Although a monoclinic C2/m structure has been previously proposed for Ln 5 Mo 2 O 12 (Ln = La-Lu and Y) members of this family based on prior single crystal diffraction data, it is found that this structural model misses many important structural features. On the basis of synchrotron powder diffraction data, it is shown that the C2/m monoclinic unit cell represents a superstructure relative to a previously unrecognized orthorhombic Immm subcell and that the superstructure derives from the ordering of interchangeable Mo 2 O 10 and LaO 6 building blocks. The superstructure for this reason is typically highly faulted, as evidenced by the increased breadth of superstructure diffraction peaks associated with a coherence length of 1-2 nm in the c* direction. Finally, it is shown that oxygen vacancies can occur when Ln = La, producing an oxygen deficient stoichiometry of La 5 Mo 2 O 11.55 and an approximately 10-fold reduction in the number of unpaired electrons due to the reduction of the average Mo valence from +4.5 to +4.05, a result confirmed by magnetic susceptibility measurements. This represents the first observation of oxygen vacancies in this family of compounds and provides an important means of continuously tuning the magnetic interactions within the one

Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel

Directory of Open Access Journals (Sweden)

Didi Dwi Anggoro

2017-05-01

Full Text Available One of many efforts to convert coal tar into alternative liquid fuel is by hydrocracking. This research aims to determine the impregnation of Co-Mo/Y zeolite, its characteristics, the effect of impregnation temperature and time, and also the best Co-Mo/Y zeolite impregnation condition for the conversion of coal tar. This research was conducted in several steps, impregnating Co from Co(NO32.6H2O and Mo from (NH46Mo7O24.4H2O into Zeolite Y in liquid media, drying at 100 °C for 24 hours, and calcination at 550 °C for 3 hours. Coal tar was then reacted with hydrogen gas (as a reactant, and Co-Mo/Zeolite Y (as a catalyst was conducted at 350 °C. Characteristic analysis showed that Co and Mo had impregnated into the Y zeolite, as well as it made no change of catalyst’s structure and increased the total acidity. The higher of impregnation temperature was increased the catalyst crystallinity, total acidity, and yield of gasoline. The longer impregnation time was reduced crystallinity value, but total acidity and yield were increased. GC analysis showed that products included into the gasoline product (C8, C9, and C10. Copyright © 2017 BCREC Group. All rights reserved Received: 13rd November 2016; Revised: 12nd February 2017; Accepted: 16th February 2017 How to Cite: Anggoro, D.D., Buchori, L., Silaen, G.C., Utami, R.N. (2017. Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2: 219-226 (doi:10.9767/bcrec.12.2.768.219-226 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.768.219-226

Nuclear magnetic resonance study of hydrogen mobility in LaY2Ni9Hx and CeY2Ni9Hx

International Nuclear Information System (INIS)

Soloninin, A.V.; Buzlukov, A.L.; Skripov, A.V.; Latroche, M.; Paul-Boncour, V.

2009-01-01

In order to investigate the mobility of hydrogen in the ternary compounds LaY 2 Ni 9 and CeY 2 Ni 9 , we have measured the proton nuclear magnetic resonance (NMR) spectra and the proton spin-lattice relaxation rates R 1 for LaY 2 Ni 9 H x (x=0.78 and 10.3) and CeY 2 Ni 9 H x (x=0.79 and 7.2). The measurements have been performed at the resonance frequencies of 14, 23.8 and 90 MHz over the temperature range of 11-404 K. For LaY 2 Ni 9 H x , the behavior of R 1 is consistent with the presence of a considerable contribution due to motionally modulated dipole-dipole interaction between nuclear spins. This contribution can be satisfactorily described in terms of the Bloembergen-Purcell-Pound model with a Gaussian distribution of activation energies for hydrogen diffusion; the value of the average activation energy resulting from such a description for LaY 2 Ni 9 H 10.3 is approximately 0.36 eV. For CeY 2 Ni 9 H x compounds, the measured proton spin-lattice relaxation rates are dominated by the contribution due to the interaction between proton spins and paramagnetic centers over the entire temperature range studied. Only qualitative information on H mobility in these compounds has been obtained from the narrowing of NMR spectra. Possible paths of H diffusion in LaY 2 Ni 9 H x and CeY 2 Ni 9 H x are discussed in terms of the distances between the interstitial sites occupied by hydrogen. - Graphical abstract: The temperature dependences of the proton spin-lattice relaxation rates R 1 measured at 14, 23.8 and 90 MHz for LaY 2 Ni 9 H 10.3 . The frequency-dependent increase in R 1 at T>250 K indicates the onset of the motional contribution to the relaxation rates

Precipitation behavior of Laves phase and its effect on toughness of 9Cr-2Mo ferritic-martensitic steel

International Nuclear Information System (INIS)

Hosoi, Y.; Wade, N.; Kunimitsu, S.; Urita, T.

1986-01-01

This study clarified the relationship between the toughness of a 9Cr-2Mo dual phase steel and precipitates formed during aging, with special attention to the Laves phase (Fe 2 Mo). The ductile-brittle transition temperature (DBTT) is increased and the upper shelf energy decreased when the Laves phase begins to precipitate during aging. Electron microscopy and X-ray diffraction indicate that elimination of Si in the steel reduces the precipitation of the Laves phase and results in maintaining good toughness. It is also noted that the toughness of the steel is controlled by the total amount of precipitates (Laves + carbides) in the aging at 873 K for more than 3.6x10 3 ks. A time-temperature-precipitation diagram for the Laves phase is established and it clearly shows that the precipitation of the Laves phase is markedly retarded by the decrease of Si content. In Si-free steel, no Laves phase is observed in the temperature and time range investigated. (orig.)

Synthesis and Characterization of SiO2@Y2MoO6:Eu3+ Core-Shell Structured Spherical Phosphors by Sol-Gel Process.

Science.gov (United States)

Li, G Z; Liu, F H; Chu, Z S; Wu, D M; Yang, L B; Li, J L; Wang, M N; Wang, Z L

2016-04-01

SiO2@Y2MoO6:Eu3+ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO2@Y2MoO6:Eu3+ core-shell phosphors. The XRD results demonstrated that the Y2MoO6:Eu3+ layers on the SiO2 spheres crystallized after being annealed at 700 °C and the crystallinity increased with raising the annealing temperature. The obtained core-shell phosphors have spherical shape with narrow size distribution (average size ca. 640 nm), non-agglomeration, and smooth surface. The thickness of the Y2MoO6:Eu3+ shells on the SiO2 cores could be easily tailored by varying the number of deposition cycles (70 nm for four deposition cycles). The Eul+ shows a strong PL emission (dominated by 5D0-7F2 red emission at 614 nm) under the excitation of 347 nm UV light. The PL intensity of Eu3+ increases with increasing the annealing temperature and the number of coating cycles.

Broadband sensitized white light emission of g-C_3N_4/Y_2MoO_6:Eu"3"+ composite phosphor under near ultraviolet excitation

International Nuclear Information System (INIS)

Han, Bing; Xue, Yongfei; Li, Pengju; Zhang, Jingtao; Zhang, Jie; Shi, Hengzhen

2015-01-01

The g-C_3N_4/Y_2MoO_6:Eu"3"+ composite phosphors were synthesized and characterized by X-ray diffraction, Fourier transform-infrared spectroscopy, ultraviolet visible diffuse reflection spectra, photoluminescence spectra and luminescence decay curves. Under the excitation of 360 nm near ultraviolet light, these composite phosphors show tunable emission from blue to red region, in which white light emission can be obtained in term of appropriate quality proportion of Y_2MoO_6:Eu"3"+ relative to g-C_3N_4/Y_2MoO_6:Eu"3"+. In addition, the emission color can be also dependent on the excitation wavelength in g-C_3N_4/Y_2MoO_6:Eu"3"+ composite phosphor. - Graphical abstract: Under the excitation of 360 nm near ultraviolet light, the g-C_3N_4/Y_2MoO_6:Eu"3"+ composite phosphors show tunable emission from blue to red region, in which white light emission can be obtained. - Highlights: • The g-C3N4/Y2MoO6:Eu"3"+ composite phosphors were synthesized and characterized. • White light emission was realized in the g-C3N4/Y2MoO6:Eu"3"+ composites under UV excitation. • A novel idea to realize the broadband sensitized white light emission in phosphors was provided.

Ionic liquid-assisted hydrothermal synthesis of dendrite-like NaY(MoO{sub 4}){sub 2}:Tb{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Tian Yue [Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China); College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China); Chen Baojiu, E-mail: chenmbj@sohu.com [Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China); Tian Bining [Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China); College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China); Sun Jiashi; Li Xiangping; Zhang Jinsu; Cheng Lihong; Zhong Haiyang; Zhong Hua [Department of Physics, Dalian Maritime University, Dalian, Liaoning 116026 (China); Meng Qingyu [School of Physics and Electronic Engineering, Harbin Normal University, Harbin 150025 (China); Hua Ruinian, E-mail: rnhua@dlnu.edu.cn [College of Life Science, Dalian Nationalities University, Dalian, Liaoning 116600 (China)

2012-07-01

Micro-sized NaY(MoO{sub 4}){sub 2}:Tb{sup 3+} phosphors with dendritic morphology was synthesized by a ionic liquid-assisted hydrothermal process. X-ray diffraction (XRD) indicated that the as-prepared product is pure tetragonal phase of NaY(MoO{sub 4}){sub 2}. Field emission scanning electron microscopy (FE-SEM) images showed that the as-prepared NaY(MoO{sub 4}){sub 2}:Tb{sup 3+} phosphors have dendritic morphology. The photoluminescent (PL) spectra displayed that the as-prepared NaY(MoO{sub 4}){sub 2}:Tb{sup 3+} phosphors show a stronger green emission with main emission wavelength 545 nm corresponding to the {sup 5}D{sub 4}{yields}{sup 7}F{sub 5} transition of Tb{sup 3+} ion, and the optimal Tb{sup 3+} doping concentration for obtaining maximum emission intensity was confirmed to be 10 mol%. Based on Van Uitert's and Dexter's models the electric dipole-dipole (D-D) interaction was confirmed to be responsible for the concentration quenching of {sup 5}D{sub 4} fluorescence of Tb{sup 3+} in the NaY(MoO{sub 4}){sub 2}:Tb{sup 3+} phosphors. The intrinsic radiative transition lifetime of {sup 5}D{sub 4} level is found to be 0.703 ms.

Effect of molecular intercalation on the local structure of superconducting Nax(NH3)yMoSe2 system

Science.gov (United States)

Simonelli, L.; Paris, E.; Wakita, T.; Marini, C.; Terashima, K.; Miao, X.; Olszewski, W.; Ramanan, N.; Heinis, D.; Kubozono, Y.; Yokoya, T.; Saini, N. L.

2017-12-01

We have studied the local structure of layered Nax(NH3)yMoSe2 system by Mo K-edge extended X-ray absorption fine structure (EXAFS) measurements performed as a function of temperature. We find that molecular intercalation in MoSe2 largely affects the Mo-Se network while Mo-Mo seems to sustain small changes. The Einstein temperature (ΘE) of Mo-Mo distance hardly changes (∼264 K) indicating that bond strength of this distance remains unaffected by intercalation. On the other hand, Mo-Se distance suffers a softening, revealed by the decrease of ΘE from ∼364 K to ∼350 K. The results indicate that Na+ ion transported by NH3 molecules may enter between the two MoSe-layers resulting reduced Se-Se coupling. Therefore, increased hybridization between Se 4p and Mo 4d orbitals due to inter-layer disorder is the likely reason of metallicity in intercalated MoSe2 and superconductivity at low temperature.

Development of social functioning and communication in school-aged (5-9 years) children with cerebral palsy

NARCIS (Netherlands)

van Schie, P.E.M.; Siebes, R.C.; Dallmeijer, A.J.; Schuengel, C.; Smits, D.W.; Gorter, J.W.; Becher, J.G.

2013-01-01

The aim of this study was to examine determinants of the course and level of social functioning and communication in school-aged children with cerebral palsy (CP) over a 2-year period. A clinic-based sample of 5 and 7 years old children with CP ( n=108; 72 males; mean age 6. y 3. mo, SD 12. mo;

Actividad química de los ligandos puente difósforo y difosfenilo en los complejos binucleares (Mo2Cp2(n-PCy2) (n-K2:K2-P2)(CO)2)-y (Mo2Cp2(n-PCy2)(n-K2:K2-P2Me)(CO)2)

OpenAIRE

Lozano Rivera, Raquel

2015-01-01

El trabajo de investigación que se recoge en la presente Memoria comprende un amplio estudio de la reactividad de complejos metálicos binucleares con ligandos puente difósforo y metildifosfenilo procedentes de la activación directa del fósforo blanco. Por un lado, se ha llevado a cabo un amplio análisis del comportamiento químico de la especie aniónica [Mo2Cp2(¿-PCy2)(¿-¿2:¿2-P2)(CO)2]- frente a electrófilos de distinta naturaleza, tales como clorofosfinas y complejos metálicos generadores...

Controlled self-decoration of Mo6SyIz (8.2 ≤ y + z ≤ 10) nanowires and their transformation to MoS2 nanotubes with gold nanoparticles

International Nuclear Information System (INIS)

Kovič, Andrej; Vengust, Damjan; Vilfan, Mojca; Mrzel, Aleš

2013-01-01

Nanowires and nanotubes decorated with gold nanoparticles are known for their excellent sensing and catalytic properties. However, the decoration of transition–metal dichalcogenide nanotubes can be very complex. Here we report on a simple procedure that enables efficient production and purification of thin bundles of Mo 6 S y I z (8.2 ≤ y + z ≤ 10) nanowires decorated with gold nanoparticles and their transformation to gold-decorated MoS 2 nanotubes. We isolated several hundred milligrams of nanowire bundles that were several microns long with average diameters of around 40 nm, and formed a stable dispersion in water without added surfactants. Gold nanoparticles were directly deposited on the nanowire bundles either in a solution or on a substrate at room temperature in a single-step reaction without any additional reducing reagents. The number of gold nanoparticles on a nanowire bundle is controlled by changing the concentration of chloroauric acid HAuCl 4 ·3H 2 O in the solution. Since the nanowires can serve as precursor crystals for fabrication of nanotubes, we were able to transform gold-decorated nanowires and produce gold-decorated MoS 2 nanotubes

Influence of Normalizing Temperature on the Microstructure and Hardness of 9Cr-1Mo ODS Steel

Energy Technology Data Exchange (ETDEWEB)

Jang, Ki Nam; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Kyu Tae [Dongguk University, Gyeongju (Korea, Republic of)

2016-10-15

Oxide dispersion strengthened(ODS) steel has superior high-temperature strength and creep properties because fine oxide particles having an excellent stability at high temperatures are uniformly distributed in the matrix. ODS steel has being developed for structure materials of sodium fast cooled reactor(SFR) because of its excellent irradiation resistance and mechanical properties. 9Cr-1Mo ODS steel has better high temperature strength and irradiation resistance than common 9Cr-1Mo steel because Y{sub 2}O{sub 3} nano-sized particles which interrupt dislocation movement and grain boundary slip are uniformly dispersed in the martensite matrix. The mechanical properties of the ODS steels are mainly determined by their microstructures, and the microstructure is considerably decided by the heat-treatment conditions. This study focused on the effect of normalizing temperature on microstructure and hardness of 9Cr-1Mo martensitic ODS steel so as to optimize the heat-treatment condition. In this study, the effect of normalizing temperature on mechanical property and microstructures of 9Cr-1Mo martensitic ODS steel was investigated. It was shown that the microhardness was steadily increased with increasing of the normalizing temperature. According to TEM observation, mechanical property of 9Cr-1Mo ODS steel was significantly affected by lath width. These observations, could be useful to understand the relationship between normalizing temperature and microstructure.

Quasicrystalline and crystalline precipitation during isothermal tempering in a 12Cr-9Ni-4Mo maraging stainless steel

International Nuclear Information System (INIS)

Liu, P.; Stigenberg, A.H.; Nilsson, J.O.

1995-01-01

A thorough microstructural investigation has been performed on a high strength maraging steel of the type 12%Cr-9%Ni-4%Mo-2%Cu-1%Ti. The major precipitate formed during isothermal aging at 475 C is a quasicrystalline phase possessing icosahedral symmetry termed R'-phase with a typical chemical composition of 48%Mo-33%Fe-13%Cr-2%Ni-4%Si. At 550 C the major precipitate is trigonal R-phase with a typical composition of 45%Mo-31%Fe-18%Cr-4%Ni-2%Si. At 550 C also Laves phase with a composition of 48%Mo-35%Fe-13%Cr-2%Ni-2%Si could be observed. At both 475 and 550 C an ordered phase termed L-phase precipitated. This minority phase has an ordered face centered cubic (f.c.c.) structure of type L1 0 . Its composition is typically 9%Fe-4%Cr-52%Ni-15%Mo.-16%Ti-4%Al. R'-phase formed at 475 C transformed to R-phase and Laves phase during aging at 550 C. In an analogous manner, R-phase and Laves phase formed at 550 C transformed to R'-phase during subsequent aging at 475 C. This transformation was rationalized by a strong similarity in crystal structure between quasicrystalline R'-phase of icosahedral symmetry and Frank-Kasper phases such as R-phase and Laves phase

Electronic structure of structural open derivatives of the [Mo6X14]2- cluster: [Mo5Cl13]2- and [Mo4I11]2-

International Nuclear Information System (INIS)

Miessner, H.; Korol'kov, D.V.

1983-01-01

The electronic structure of structural open derivatives of the [Mo 6 X 14 ] 2 - -cluster [Mo 5 Cl 13 ] 2 - and [Mo 4 I 11 ] 2 - has been studied by the EHMO method. In [Mo 5 Cl 13 ] 2 - 9 occupied MO's with dominant Mo4d character are responsible for the formation of the 8 metal-metal bonds. In [Mo 4 I 11 ] 2 - the stronger covalent character of the Mo-I bonds affects the localization and the energy of molecular orbitals and also the charge distribution. The metal-metal bonds are formed by 8 MO's containing considerable participation of halogen AO's contrary to the chloride cluster. There is no bonding between the Mo atoms at the wing tips of the Mo 4 butterfly and the reason for decreasing the dihedral angle between the Mo 3 planes in [Mo 4 I 11 ] 2 - compared with the octahedral angle is apparently the stabilization of the whole system (Mo-Mo and Mo-I bonds). The unpaired electron occupies in both clusters a slightly antibonding (with regard to the Mo-Mo bonds) orbital. (author)

Precipitation hardening in a 12%Cr-9%Ni-4%Mo-2%Cu stainless steel

International Nuclear Information System (INIS)

Haettestrand, Mats; Nilsson, Jan-Olof; Stiller, Krystyna; Liu Ping; Andersson, Marcus

2004-01-01

A combination of complementary techniques including one-dimensional and three-dimensional atom probe, energy-filtered transmission electron microscopy and conventional transmission electron microscopy has been used to assess the precipitation reactions at 475 deg. C in a 12%Cr-9%Ni-4%Mo-2%Cu precipitation hardening stainless steel. The continuous hardening up to at least 1000 h of ageing was attributed to a sequence of precipitation reactions involving nickel-rich precipitates nucleating at copper clusters followed by molybdenum-rich quasicrystalline precipitates and nickel-rich precipitates of type L1 0 . An estimate of the relative contributions to the strength increment during tempering based on measurements of particle densities was performed. Nickel-rich precipitates were found to play the most important role up to about 40 h of ageing after which the effect of quasicrystalline particles became increasingly important

Synthesis, crystal structure and photoluminescent properties of Eu{sup 3+} ion-activated R{sub 4}MoO{sub 9} (R = Y, Gd, and Lu)

Energy Technology Data Exchange (ETDEWEB)

Li, Huaiyong [Department of Materials Science and Engineering, Liaocheng University, Liaocheng 252059 (China); Moon, Byung Kee; Choi, Byung Chun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Jeong, Jung Hyun, E-mail: jhjeong@pknu.ac.kr [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Yang, Hyun Kyoung [Jeju Global Research Center, Korea Institute of Energy Research, Jeju 695-971 (Korea, Republic of); Jang, Kiwan; Lee, Ho Sueb [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Yi, Soung Soo [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of)

2013-05-15

Rare earth molybdates R{sub 4}MoO{sub 9} (R = Y, Gd, and Lu) with Eu{sup 3+} ion-doped were synthesized by solid-state reaction. The phase structure, optical absorption and photoluminescence properties of the as-prepared powder samples were studied. The powder X-ray diffraction patterns indicated that all the compounds crystallized in a hexagonal structure, and the lattice parameters reduced in the order of the ionic radii of R. The UV–visible diffuse reflectance spectra revealed that the compounds had a strong absorption of near-UV light due to the excitation of MoO{sub 6} groups in the host lattices. The energy absorbed by the host lattices could then be transferred to doped Eu{sup 3+} ions, resulting in red emission due to the f–f transitions of Eu{sup 3+} ions. The optical absorption and photoluminescence properties of the compounds indicated that they might be candidates as the color-conversion red phosphors for solid-state lighting. - Highlights: ► Structure, optical and photoluminescence properties of Eu{sup 3+} ion-activated R{sub 4}MoO{sub 9} were studied. ► Energy transfer from MoO{sub x} to Eu{sup 3+} can be used to convert near-UV to red light. ► R{sub 4}MoO{sub 9}:Eu might be candidate for color-conversion red phosphors excited by near-UV light.

Laves-phase evolution during aging in 9Cr-1.8W-0.5Mo-VNb steel for USC power plants

Energy Technology Data Exchange (ETDEWEB)

Wang, Xue, E-mail: wangxue2011@whu.edu.cn [School of Power and Mechanics, Wuhan University, Wuhan 430072 (China); Xu, Qiang [School of Computing and Engineering, The University of Huddersfield, Huddersfield HD1 3DH, England (United Kingdom); Yu, Shu-min; Hu, Lei [School of Power and Mechanics, Wuhan University, Wuhan 430072 (China); Liu, Hong [DongFang Boiler Group Co.,Ltd., Zigong 643001 (China); Ren, Yao-yao [School of Power and Mechanics, Wuhan University, Wuhan 430072 (China)

2015-08-01

Long term precipitation and coarsening of Laves-phase in tungsten strengthened 9% Cr steel under thermal aging at 923 K was investigated and reported in this paper. It experimentally measured the evolution of mean particle size, the number density, the volume fraction of Laves-phase precipitates, the partition coefficients of W and Mo in the matrix, as well as the change of hardness. Its main conclusions were: 1) Laves-phase nucleates and grows rapidly on grain boundaries and lath boundaries within the first 1500 h of aging time; 2) The two stages characteristics and kinetics of Laves-phase nucleation and growth which were determined experimentally; 3) The coarsening of Laves-phase is much faster than that of M{sub 23}C{sub 6} carbides; 4) The precipitation of Laves-phase produces a pronounced matrix depletion of W and Mo atoms; and 5) The precipitated Laves-phase gives rise to weaker precipitation strengthening in comparison with M{sub 23}C{sub 6} carbides, and causes the loss of hardness due to the depletion of Mo and W from the solid solution. This paper contributes to the knowledge of kinetics of Laves-phase precipitation and coarsening, providing the essential information for comparative investigation of creep damage mechanisms. This paper also contributes to the understanding the creep damage broadly. - Highlights: • The characteristics of precipitation and coarsening of Laves-phase were determined. • The matrix depletion of W and Mo due to Laves-phase precipitation was quantified. • The effect of precipitated Laves-phase on the hardness was evaluated.

A first-principles study of structure, orbital interactions and atomic oxygen and OH adsorption on Mo-, Sc- and Y-doped nickel bimetallic clusters

International Nuclear Information System (INIS)

Das, Nishith Kumar; Shoji, Tetsuo

2013-01-01

Highlights: •Mo-doped nickel clusters are energetically more stable than the Sc and Y-doped clusters (n ⩾ 10). •Mo atom exhibits center at the cluster rather than edge, while Sc and Y atom sit at the edge. •The metallic s, d orbitals are mainly dominated on the stability of nanoclusters. •The oxygen and OH adsorption energy of Mo-doped cluster are higher than those of other nanoclusters. •2p Orbitals are strongly bonds with Mo 4d, and a weakly interacts with Ni 3d, 4s and Mo 5s orbitals. -- Abstract: Density functional theory (DFT) has been used to study the stability, orbitals interactions and oxygen and hydroxyl chemisorption properties of Ni n M (1 ⩽ n ⩽ 12) clusters. A single atom doped-nickel clusters increase the stability, and icosahedral Ni 12 Mo cluster is the most stable structure. Molybdenum atom prefers to exhibit center at the cluster (n ⩾ 10) rather than edge, while Sc and Y atom remain at the edge. The Ni–Mo bond lengths are smaller than the Ni–Sc and Ni–Y. The pDOS results show that the d–d orbitals interactions are mainly dominating on the stability of clusters, while p orbitals have a small effect on the stability. The Mo-doped nanoclusters have the highest oxygen and OH chemisorption energy, and the most favorable adsorption site is on the top Mo site. The larger cluster distortion is found for the Sc- and Y-doped structures compared to other clusters. The oxygen 2p orbitals are strongly hybridizing with the Mo 4d orbitals (n < 9) and a little interaction between oxygen 2p and Ni 3d, 4s and Mo 5s orbitals. The Mo-doped clusters are significantly increased the chemisorption energies that might improve the passive film adherence of nanoalloys

Thermodynamic evidence for phase transition in MoO2-δ

International Nuclear Information System (INIS)

Jacob, K.T.; Saji, V.S.; Gopalakrishnan, J.; Waseda, Y.

2007-01-01

The standard Gibbs free energy of formation of MoO 2-δ , Δ f G 0 (MoO 2-δ ), has been measured over a wide temperature range (925 to 1925) K using an advanced version of bi-electrolyte solid-state electrochemical cell incorporating a buffer electrode: Pt vertical bar Mo + MoO 2-δ -parallel (Y 2 O 3 )ThO 2 -parallel (CaO)ZrO 2 -parallel O 2 (0.1 MPa) vertical bar Pt The Gibbs free energy of formation of MoO 2-δ , which is directly related to the measured cell e.m.f., can be represented by two linear segments: Δ f G 0 (MoO 2-δ )±570/(J.mol -1 )=-579,821+170.003(T/K), in the temperature range (925 to 1533) K, and Δ f G 0 (MoO 2-δ )±510/(J.mol -1 )=-564,634+160.096(T/K), in the temperature range (1533 to 1925) K. The change in slope at T = 1533 K is probably related to the phase transition of MoO 2 from monoclinic structure with space group P2 1 /c to tetragonal structure characteristic of rutile with space group P4 2 /mnm. The enthalpy and entropy change for the phase transition are: ΔH tr = (15.19 ± 2.1) kJ . mol -1 ; ΔS tr (9.91 ± 1.27) J . mol -1 . K -1 . The standard enthalpy of formation of MoO 2-δ at T = 298.15 K assessed by the third-law method is: Δ f H 0 (MoO 2-δ ) = (-592.28 ± 0.33) kJ . mol -1 . The new measurements refine thermodynamic data for MoO 2

Creep Rupture Analysis and Life Estimation of 1.25Cr-0.5Mo, 2.25Cr-1Mo and Modified 9Cr-1Mo Steel: A Comparative Study

Science.gov (United States)

Roy, Prabir Kumar

2018-04-01

This paper highlights a comparative assessment of creep life of 1.25Cr-0.5Mo, 2.25Cr-1Mo and modified 9Cr-1Mo steels based on accelerated creep rupture tests. Creep rupture test data have been analysed and creep life of the above mentioned materials have been assessed using Larson Miller parameter at the stress levels of 60 and 42 MPa for different temperatures. Limiting steam temperatures for minimum design life of 105 h at 42 and 60 MPa for the above mentioned steels have also been calculated. Microstructural studies for the three above mentioned steels are also done.

Detailed investigation of the β-decay of the 9/2+ ground state of 99Nb to levels in 99Mo

International Nuclear Information System (INIS)

Lhersonneau, G.; Persson, J.R.; Suhonen, J.; Dendooven, P.; Wang, J.C.; Aeystoe, J.

1997-01-01

The decay of 99 Nb to 99 Mo has been investigated. The use of the ion-guide technique for on-line mass separation and of a Ge-array for γ-ray detection have allowed the observation of decay branchings lower than 10 -3 . Medium-spin levels, some already known from reaction studies and new ones at high energy, are populated. The β-feeding patterns of the decays of the 9/2 + states in 99 Nb and in its isotones 97 Y, and 101 Tc are qualitatively reproduced by QRPA calculations. (orig.). With 5 figs., 7 tabs

Mo{sub 2}B{sub 4}O{sub 9} - connecting borate and metal-cluster chemistry

Energy Technology Data Exchange (ETDEWEB)

Schmitt, Martin K.; Huppertz, Hubert [Institut fuer Allgemeine, Anorganische und Theoretische Chemie, Universitaet Innsbruck (Austria); Janka, Oliver; Poettgen, Rainer [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster (Germany); Benndorf, Christopher [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster (Germany); Institut fuer Physikalische Chemie, Universitaet Muenster (Germany); Institut fuer Mineralogie, Kristallographie und Materialwissenschaften, Universitaet Leipzig (Germany); Oliveira, Marcos de Jr. [Sao Carlos Institute of Physics, University of Sao Paulo, Sao Carlos (Brazil); Eckert, Hellmut [Institut fuer Physikalische Chemie, Universitaet Muenster (Germany); Sao Carlos Institute of Physics, University of Sao Paulo, Sao Carlos (Brazil); Pielnhofer, Florian; Tragl, Amadeus-Samuel [Institut fuer Anorganische Chemie, Universitaet Regensburg (Germany); Weihrich, Richard [Institut fuer Materials Resource Management, Universitaet Augsburg (Germany); Joachim, Bastian [Institut fuer Mineralogie und Petrographie, Universitaet Innsbruck (Austria); Johrendt, Dirk [Department Chemie, Ludwig-Maximilians-Universitaet Muenchen (Germany)

2017-06-01

We report on the first thoroughly characterized molybdenum borate, which was synthesized in a high-pressure/high-temperature experiment at 12.3 GPa/1300 C using a Walker-type multianvil apparatus. Mo{sub 2}B{sub 4}O{sub 9} incorporates tetrahedral molybdenum clusters into an anionic borate crystal structure - a structural motif that has never been observed before in the wide field of borate crystal chemistry. The six bonding molecular orbitals of the [Mo{sub 4}] tetrahedron are completely filled with 12 electrons, which are fully delocalized over the four molybdenum atoms. This finding is in agreement with the results of the magnetic measurements, which confirmed the diamagnetic character of Mo{sub 2}B{sub 4}O{sub 9}. The two four-coordinated boron sites can be differentiated in the {sup 11}B MAS-NMR spectrum because of the strongly different degrees of local distortions. Experimentally obtained IR and Raman bands were assigned to vibrational modes based on DFT calculations. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Photoluminescence properties of Eu2+-activated Ca2Y2Si2O9 phosphor

NARCIS (Netherlands)

Zhang, Zhijun; Delsing, A.C.A.; Notten, P.H.L.; Zhao, Jingtai; Hintzen, H.T.J.M.

2012-01-01

Eu2+-activated Ca2Y2Si2O9 phosphors with different Eu2+ concentrations have been prepared by a solid-state reaction method at high temperature and their photoluminescence (PL) properties were investigated. Photoluminescence results show that Eu2+-doped Ca2Y2Si2O9 can be efficiently excited by

Sr3Fe5/4Mo3/4O6.9, an n = 2 Ruddlesen-Popper Phase: Synthesis and Properties

International Nuclear Information System (INIS)

Whaley, L.; Lobanov, M.; Sehptyakov, D.; Croft, M.; Ramanujachary, K.; Lofland, S.; Stephens, P.; Her, J.; Van Tendeloo, G.

2006-01-01

In a systematic search for an oxygen-stoichiometric phase, Sr 3 (FeMo)O 7 , in a range of iron-to-molybdenum ratios greater than 1:1 that typically give phase mixtures, we have found an n = 2 Ruddlesden-Popper phase, Sr 3 Fe 5/4 Mo 3/4 O 6.9 , as supported by synchrotron powder X-ray diffraction (SPXD), high-resolution transmission electron microscopy (HREM), and powder neutron diffraction (PND) results. By SPXD, this oxygen-deficient, B-site disordered, two-dimensional analogue of Sr2FeMoO6 adopts tetragonal I4/mmm symmetry (a = b = 3.92449(5) Angstroms; c = 20.3423(3) Angstroms) with vacancies at the O(1) oxygen site and with a composition that refines to a nominal stoichiometry Sr 3 Fe 5/4 Mo 3/4 O 6.9 . The two-phase SPXD refinement includes Sr 3 Fe 5/4 Mo 3/4 O 6.9 (95.7%) and a double-perovskite (DP) intergrowth, Sr 2 FeMoO 6 (4.3%), consistent with HREM studies in which DP intergrowths but no individual DP grains were found. The G-type antiferromagnetically (AFM)-ordered structure of the phase, with the magnetic cell a m = √2a ∼ 5.548 Angstroms, c m = c ∼ 20.35 Angstroms, derived from PND data, displays a saturated moment of 2.17(1) μ B at 9 K and an asynchronous decrease of the in-plane component of the Fe/Mo moment (μ xy ), with respect to the out-of-plane moment (μ z ) upon increasing temperature from 9 K up to the Neel temperature, TN ∼ 150 K. No structural transitions were observed over the entire temperature range studied: from 1.5 to 500 K. The temperature-dependent resistivity is consistent with Efros-Shklovskii variable-range hopping, applicable to two ranges of temperature (189 K RT ∼ 3 μ(Omega)·cm). A small negative magnetoresistance is observed (∼2.5%) at 5 T near the ordering temperature (∼150 K). The temperature-dependent magnetic susceptibility shows an inflection between 125 and 150 K, consistent with the AFM ordering temperature (∼150 K) observed by PND. X-ray near-edge spectroscopy data are consistent with formal

Fractographic examination of HT-9 and 9Cr-1Mo Charpy specimens irradiated in the AD-2 test

International Nuclear Information System (INIS)

Gelles, D.S.; Hu, W.L.

1983-01-01

Fracture surface topologies have been examined using scanning electron microscopy for 20 selected half sized Charpy impact specimens of HT-9 and Modified 9Cr-1Mo in order to provide improved understanding of fracture toughness degradation as a result of irradiation for Path E alloys. The specimen matrix included unirradiated specimens and specimens irradiated in EBR-II in the AD-2 experiment. Also, hardness measurements have been made on selected irradiated Charpy specimens. The results of examinations indicate that irradiation hardening due to G-phase formation at 390 0 C is responsible for the large shift in ductile-to-brittle transition temperature (DBTT) found in HT-9. Toughness degradation in HT-9 observed following higher temperature irradiations is attributed to precipitation at delta ferrite stringers. Reductions in toughness as a consequence of irradiation in Modified 9Cr-1Mo are attributed to in-reactor precipitation of (V,Nb)C and M 23 C 6 . It is shown that crack propagation rates for ductile and brittle failure modes can be measured, that they differ by over an order of magnitude and that unexpected multiple shifts in fracture mode from ductile to brittle failure can be attributed to the effect of delta ferrite stringers on crack propagation rates

Effect of Mo/B atomic ratio on the properties of Mo2NiB2-based cermets

International Nuclear Information System (INIS)

Xie, Lang; Li, XiaoBo; Zhang, Dan; Yi, Li; Gao, XiaoQing; Xiangtan Univ.

2015-01-01

Using three elementary substances, Mo, Ni, and amorphous B as raw materials, four series of Mo 2 NiB 2 -based cermets with the Mo/B atomic ratio ranging from 0.9 to 1.2 were successfully prepared via reaction sintering. The effect of Mo/B atomic ratio on the microstructure and properties was studied for the cermets. The results indicate that there is a strong correlation between the Mo/B atomic ratio and properties. The transverse rupture strength of the cermets increases with an increase in Mo/B ratio and shows a maximum value of 1 872 MPa at an Mo/B atomic ratio of 1.1 and then decreases with increasing Mo/B atomic ratio. The hardness and the corrosion resistance of the cermets increase monotonically with an increase in Mo/B atomic ratio. In Mo-rich cermets with an atomic ratio of Mo/B above 1.1, a small amount Ni-Mo intermetallic compound is found precipitated at the interface of Mo 2 NiB 2 grains.

Broadband sensitized white light emission of g-C{sub 3}N{sub 4}/Y{sub 2}MoO{sub 6}:Eu{sup 3+} composite phosphor under near ultraviolet excitation

Energy Technology Data Exchange (ETDEWEB)

Han, Bing, E-mail: hanbing@zzuli.edu.cn [School of Material and Chemical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002 (China); Xue, Yongfei; Li, Pengju [School of Material and Chemical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002 (China); Zhang, Jingtao [School of Food and Bioengineering, Zhengzhou University of Light Industry, Zhengzhou 450002 (China); Zhang, Jie [School of Material and Chemical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002 (China); Shi, Hengzhen, E-mail: shihz@zzuli.edu.cn [School of Material and Chemical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002 (China)

2015-12-15

The g-C{sub 3}N{sub 4}/Y{sub 2}MoO{sub 6}:Eu{sup 3+} composite phosphors were synthesized and characterized by X-ray diffraction, Fourier transform-infrared spectroscopy, ultraviolet visible diffuse reflection spectra, photoluminescence spectra and luminescence decay curves. Under the excitation of 360 nm near ultraviolet light, these composite phosphors show tunable emission from blue to red region, in which white light emission can be obtained in term of appropriate quality proportion of Y{sub 2}MoO{sub 6}:Eu{sup 3+} relative to g-C{sub 3}N{sub 4}/Y{sub 2}MoO{sub 6}:Eu{sup 3+}. In addition, the emission color can be also dependent on the excitation wavelength in g-C{sub 3}N{sub 4}/Y{sub 2}MoO{sub 6}:Eu{sup 3+} composite phosphor. - Graphical abstract: Under the excitation of 360 nm near ultraviolet light, the g-C{sub 3}N{sub 4}/Y{sub 2}MoO{sub 6}:Eu{sup 3+} composite phosphors show tunable emission from blue to red region, in which white light emission can be obtained. - Highlights: • The g-C3N4/Y2MoO6:Eu{sup 3+} composite phosphors were synthesized and characterized. • White light emission was realized in the g-C3N4/Y2MoO6:Eu{sup 3+} composites under UV excitation. • A novel idea to realize the broadband sensitized white light emission in phosphors was provided.

Mild hydrothermal synthesis, crystal structure, spectroscopic and magnetic properties of the [MxIIM2.5-xIII(H2O)2(HPIIIO3)y(PVO4)2-yF] [M=Fe, x=2.08, y=1.58; M=Co, Ni, x=2.5, y=2] compounds

International Nuclear Information System (INIS)

Orive, Joseba; Mesa, Jose L.; Legarra, Estibaliz; Plazaola, Fernando; Arriortua, Maria I.; Rojo, Teofilo

2009-01-01

The [M x II M 2.5-x III (H 2 O) 2 (HP III O 3 ) y (P V O 4 ) 2-y F] [M=Fe (1), x=2.08, y=1.58; M=Co (2), x=2.5, y=2; Ni (3), x=2.5, y=2] compounds have been synthesized using mild hydrothermal conditions at 170 deg. C during five days. Single-crystals of (1) and (2), and polycrystalline sample of (3) were obtained. These isostructural compounds crystallize in the orthorhombic system, space group Aba2, with a=9.9598(2), b=18.8149(4) and c=8.5751(2) A for (1), a=9.9142(7), b=18.570(1) and c=8.4920(5) A for (2) and a=9.8038(2), b=18.2453(2) and c=8.4106(1) A for (3), with Z=8 in the three phases. An X-ray diffraction study reveals that the crystal structure is composed of a three-dimensional skeleton formed by [MO 5 F] and [MO 4 F 2 ] (M=Fe, Co and Ni) octahedra and [HPO 3 ] tetrahedra, partially substituted by [PO 4 ] tetrahedra in phase (1). The IR spectra show the vibrational modes of the water molecules and those of the (HPO 3 ) 2- tetrahedral oxoanions. The thermal study indicates that the limit of thermal stability of these phases is 195 deg. C for (1) and 315 deg. C for (2) and (3). The electronic absorption spectroscopy shows the characteristic bands of the Fe(II), Co(II) and Ni(II) high-spin cations in slightly distorted octahedral geometry. Magnetic measurements indicate the existence of global antiferromagnetic interactions between the metallic centers with a ferromagnetic transition in the three compounds at 28, 14 and 21 K for (1), (2) and (3), respectively. Compound (1) exhibits a hysteresis loop with remnant magnetization and coercive field values of 0.72 emu/mol and 880 Oe, respectively. - Abstract: Polyhedral view of the crystal structure of the [M x II M 2.5-x III (H 2 O) 2 (HP III O 3 ) y (P IV O 4 ) 2-y F] [M=Fe, x=2.08, y=1.58; M=Co, Ni, x=2.5, y=2] compounds showing the sheets along the [001] direction.

Effects of prenatal multiple micronutrient supplementation on growth and cognition through 2 y of age in rural Bangladesh: the JiVitA-3 Trial.

Science.gov (United States)

Christian, Parul; Kim, Jeongyong; Mehra, Sucheta; Shaikh, Saijuddin; Ali, Hasmot; Shamim, Abu Ahmed; Wu, Lee; Klemm, Rolf; Labrique, Alain B; West, Keith P

2016-10-01

Childhood undernutrition may have prenatal origins, and the impact of prenatal interventions on postnatal growth is not well known. We assessed the effects of prenatal multiple micronutrient (MM) supplementation on child growth and cognitive development. In a cluster-randomized controlled trial in rural Bangladesh, prenatal MM supplementation compared with iron-folic acid (IFA) supplementation was examined for its impact on growth assessed longitudinally from birth up to 24 mo of age (n = 8529) and, in a subsample (n = 734), on cognitive function at 24 mo of age by use of the Bayley scales of infant and toddler development-third edition test. Prevalence of stunting at birth [length for age z score (LAZ): growth. Ponderal and linear growth velocities were somewhat slower from 3 to 12 mo of age in the MM group than in the IFA group, but not from 12 to 24 mo of age. There was no difference between groups on composite scores of cognition, language, and motor performance at 24 mo of age. In this Bangladeshi trial, maternal pre- and postnatal MM supplementation resulted in improvements in LAZ and reduction in stunting through 3 mo of age, but not thereafter and had no impact on cognitive and motor function at 2 y. This trial was registered at clinicaltrials.gov as NCT000860470. © 2016 American Society for Nutrition.

Estimation of "9"9Mo production rates from natural molybdenum in research reactors

International Nuclear Information System (INIS)

Blaauw, M.; Chakrova, Y.; Jacimovic, R.; Kling, A.

2017-01-01

Molybdenum-99 is one of the most important radionuclides for medical diagnostics. In 2015, the International Atomic Energy Agency organized a round-robin exercise where the participants measured and calculated specific saturation activities achievable for the "9"8Mo(n,γ)"9"9Mo reaction. This reaction is of interest as a means to locally, and on a small scale, produce "9"9Mo from natural molybdenum. The current paper summarises a set of experimental results and reviews the methodology for calculating the corresponding saturation activities. Activation by epithermal neutrons and also epithermal neutron self-shielding are found to be of high importance in this case. (author)

Microstructural and electrical characterizations of tungsten-doped La₂Mo₂O₉ prepared by spray pyrolysis

DEFF Research Database (Denmark)

Baqué, Laura; Vega-Castillo, Jesús; Georges, Samuel

2013-01-01

La2Mo2 − xWxO9 (x=0, 0.5, 1.0, and 1.3) nanocrystalline powders were synthesized by spray pyrolysis (SP) assisted by an ultrasonic atomizer. Microstructure, sinterability and thermal stability of the prepared powders were investigated. Spherical particles of 430 to 530 nm in diameter and crystall......La2Mo2 − xWxO9 (x=0, 0.5, 1.0, and 1.3) nanocrystalline powders were synthesized by spray pyrolysis (SP) assisted by an ultrasonic atomizer. Microstructure, sinterability and thermal stability of the prepared powders were investigated. Spherical particles of 430 to 530 nm in diameter...... by applying different sintering programs starting from La2Mo2 − xWxO9 powders (x=0 and 1.3) obtained by SP and SSR processes. The electrical properties of these ionic conductors were analyzed by Electrochemical Impedance Spectroscopy (EIS) and correlated with microstructural observations. No significant...... variation of the electrical properties of these ionic conductors was found as compared to conventional ceramics with remarkable microstructural differences....

Enhanced Selectivity and Uptake Capacity of CO2 and Toluene Adsorption in Co0.5 M0.33 MoS4 (M= Sb or Y) Chalcogels by Impregnated Metal Salts

KAUST Repository

Adhiam, Fatima Abdullah Ahmed

2017-11-17

The synthesis of metal chalcogenide aerogels Co0.5M0.33MoS4 (M= Sb or Y) by the sol-gel method is reported. In this system, the building blocks [MoS4]2− chelated with Co2+ and (Sb3+) or (Y3+) salts in nonaqueous solvents forming amorphous networks with a gel property. The chalcogels obtained after supercritical drying have BET surface areas of 176 m2 g−1 (Co0.5Sb0.33MoS4) and 145 m2 g−1 (Co0.5Y0.33MoS4). Electron microscopy and physisorption studies reveal that the new materials are porous with wide pore size distribution and average pore width of 16 nm. These chalcogels show higher adsorption capacity of toluene vapor (Co0.5Sb0.33MoS4: 387 mg g−1) and (Co0.5Y0.33MoS4: 304 mg g−1) over cyclohexane vapor and high selectivity of CO2 over CH4 or H2, Co0.5Sb0.33MoS4 (CO2/H2: 80 and CO2/CH4: 21), Co0.5Y0.33MoS4 (CO2/H2: 27 and CO2/CH4: 15). We also demonstrated that the impregnation of various metal species like Li+, Mg2+, and Ni2+ significantly enhanced the uptake capacity and selectivity of toluene and CO2 adsorptions in the chacogels.

Breastfeeding and complementary feeding in relation to body mass index and overweight at ages 7 and 11 y: a path analysis within the Danish National Birth Cohort.

Science.gov (United States)

Morgen, Camilla Schmidt; Ängquist, Lars; Baker, Jennifer L; Andersen, Anne-Marie Nybo; Sørensen, Thorkild I A; Michaelsen, Kim F

2018-03-01

Infant feeding may play an important role in the development of childhood overweight and obesity. The objective of this study was to examine whether duration of breastfeeding (BF), timing of introduction of complementary food, and protein intake at age 18 mo are associated with body mass index [BMI (measured in kg/m2)] and overweight at ages 7 and 11 y, independent of BMI during infancy. Children participating in the Danish National Birth Cohort were followed up at ages 7 and 11 y. Information on infant feeding, protein intake at age 18 mo, Ponderal Index at birth, child BMI (at ages 5 mo, 12 mo, 7 y, and 11 y), and several parental factors was available. Path analysis was used to assess the direct and indirect effects of infant feeding on BMI z scores (BMIz) at ages 7 (n = 36,481) and 11 y (n = 22,047). Logistic regression analyses were used to examine associations with overweight. Duration of BF was not associated with childhood BMIz at ages 7 and 11 y. Earlier introduction of complementary food (y, but with a 0.069 (95% CI: 0.021, 0.117, P = 0.005) higher BMIz at age 11 y and increased risk of overweight at age 11 y (OR 1.44; 95% CI: 1.04, 2.00; P = 0.03). Protein intake from dairy products (per 5 g/d) was associated with higher BMIz only at age 7 y (OR: 0.012; 95% CI: 0.003, 0.021; P = 0.007). Protein intake from meat and fish (per 2 g/d) was associated with a 0.010 (95% CI: 0.004, 0.017; P = 0.003) higher BMIz at age 7 y, a 0.013 (95% CI: 0.005, 0.020; P = 0.002) higher BMIz at age 11 y and increased odds of overweight at age 7 y (OR: 1.07; 95% CI: 1.03, 1.10; P y. Intake of protein from meat and fish at age 18 mo was associated with higher BMIz and risk of overweight in childhood. However, the effect sizes were small. Early introduction of complementary food may be associated with child BMIz and child overweight. This study was registered at www.clinicaltrials.gov as NCT03334760.

Synthesis, characterization and thermal stability of solid solutions Zr (Y, Fe, MoO2

Directory of Open Access Journals (Sweden)

Felipe Legorreta-García

2015-05-01

Full Text Available The synthesis of Fe3+, Mo4+ and Y3+ fully stabilized zirconia by the nitrate/urea combustion route and thermal stability in air was investigated. The solid solution obtained was characterized by X ray diffraction (XRD, scanning electron microscopy (SEM and used the BET method for determining specific surface. The ceramic powders obtained were calcined at 1473 K in air atmosphere in order to determine their thermal stability. The scanning electron microscopy (SEM results showed a homogeneous grain surface, measuring several tens of micrometers across. The crystallographic study revealed that by this method it was successfully achieved zirconia doped with Fe3+, Mo4+ and Y3+ ions in the zirconia tetragonal monophase, even after calcinations.

Nanocomposite Nd-Y-Fe-B-Mo bulk magnets prepared by injection casting technique

Energy Technology Data Exchange (ETDEWEB)

Tao, Shan [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China); Ahmad, Zubair [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, Pengyue [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China); Yan, Mi, E-mail: mse_yanmi@zju.edu.cn [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zheng, Xiaomei [Magnetism Key Laboratory of Zhejiang Province, China Jiliang University, Hangzhou 310018 (China)

2017-09-01

Highlights: • Nanocomposite Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} sheet magnets were synthesized by injection casting. • High coercivity of 1289 kA/m was obtained for the directly casted magnet. • Magnetic properties arise from magnetically exchange coupled soft and hard phases. - Abstract: The phase composition, magnetic and microstructural properties of Nd{sub 2}Fe{sub 14}B/(α-Fe, Fe{sub 3}B) nanocomposite magnets produced by injection casting technique have been studied. Magnetic hysteresis loop of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} permanent magnet demonstrates the coercivity as high as 1289 kA/m. Electron microscopy elucidates a microstructure composed of magnetically soft α-Fe, Fe{sub 3}B and hard Nd{sub 2}Fe{sub 14}B/Y{sub 2}Fe{sub 14}B nanograins (20–50 nm) separated by ultra-thin grain boundary layer. The Henkel plot curve of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} magnet yields the existence of exchange coupling interactions between soft and hard phases. Macroscopically large size sheet magnet is obtained due to high glass forming ability of the Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} alloy derived from large atomic radius mismatch and negative enthalpy of alloy constituent elements. The high coercivity of the magnet is attributed to the magnetically hard phase increment, nucleation of reverse domains and the presence of thin grain boundary phase. Good magnetic properties such as remanence of 0.51 T, coercivity of 1289 kA/m and maximum energy product of 46.2 kJ/m{sup 3} are obtained in directly casted Nd{sub 7}Y{sub 6}Fe{sub 61}B{sub 22}Mo{sub 4} sheet magnets.

Enhanced orange-red emission by using Mo codoped in Ba2CaWO6: Eu3+, Li+ phosphor under near UV excitation

International Nuclear Information System (INIS)

Sun, Xiaoyuan; Hao, Zhendong; Li, Chunjie; He, Xiaoguang; Qi, Haiyan; Yu, Lijun; Luo, Yongshi; Zhang, Jiahua; Gao, Jiwei; Zhong, Ruixia

2013-01-01

The orange-red emitting phosphors Ba 2 Ca 0.9 Mo x W 1−x O 6 :Eu 3+ 0.05 , Li + 0.05 (x=0, 0.05, 0.1, 0.15, 0.2, 0.25, 0.5, 0.75, and 1.0) and Ba 2 Ca 1−2y Mo 0.2 W 0.8 O 6 :Eu 3+ y , Li + y (y=0.03, 0.05, 0.07, 0.1, and 0.15) were synthesized. The crystalline structure and photoluminescence properties of these phosphors were described. The strong orange-red emission of Eu 3+ ( 5 D 0 — 7 F 1 transition) at around 593 nm was observed. Addition of Mo strongly enhances the charge transfer band absorption in the near ultraviolet region that corresponds to near ultraviolet white light emitting diode. The dependence of photoluminescence intensities on Eu 3+ concentrations with optimal Mo concentration under 400 nm excitation was studied. The phosphor is considered to be a promising orange-red emitting phosphor for near ultraviolet GaN-based white light emitting diode. - Highlights: ► The samples form solid solutions when Mo is added into Ba 2 CaWO 6 : Eu 3+ , Li + phosphors. ► Addition of Mo in Ba 2 CaWO 6 : Eu 3+ , Li + shifts the PLE spectra maximum from UV region to near UV region. ► In Ba 2 CaMo x W 1−x O 6 :Eu 3+ , Li + , the most efficient concentrations occur at 0.1 and 0.2 for Eu and Mo.

Mass spectrometric determination of stability of gaseous BaMoO2, Ba2MoO4, Ba2MoO5, Ba2Mo2O8 molecules

International Nuclear Information System (INIS)

Kudin, L.S.; Balduchchi, Dzh.; Dzhil'i, G.; Gvido, M.

1982-01-01

During the mass spectrometric investigation of BaCrO 4 evaporation Cr + , Ba + , BaO + main ions are recorded as well as BaMoO 4 + , BaMoO 3 + , BaMoO 2 + , BaMoO + , BaMoO 4 + , Ba 2 MoO 5 + , BaMo 2 O 8 + ions - the products of ionization of three-component (Ba, Mo, M) molecules, forming as a result of substance chemical interaction with the material of an effusion cell (Mo). Heats of formation of BaMoO 2 , Ba 2 MoO 4 , Ba 2 MoO 5 and Ba 2 Mo 2 O 8 molecules which constituted - 577+-70, -1343+-115, -1464+-70, -2393+-90 k J/mol respectively are determined on the base of the analysis of curves of ionisation efficiency and of reaction heats Ba 2 MoO 5 =BaO+BaMoO 4 , ΔH 0 0 =322+-60 kJ/mol Ba 2 Mo 2 O 8 =2BaMoO 4 , ΔH 0 0 =351+-80 kJ/mol calculated with the use of third low of thermodynamics [ru

Characteristics of Modified 9Cr-1Mo Steel for Reactor Pressure Vessel of Very High Temperature Gas Cooled Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung Ho; Ryu, W. S.; Han, Chang Hee; Yoon, J. H.; Chang, Jong Hwa

2004-11-15

Many researches and developments have been progressed for the construction of VHTR by 2020 in Korea. Modified 9Cr-1Mo steel has been receiving attention for the application to the reactor pressure vessel material of VHTR. We collected and analyzed the research data for modified 9Cr-1Mo steel in order to understand the characteristics of modified 9Cr-1Mo steel. The modified 9Cr-1Mo steel is a modified alloy system similar to conventional 9Cr-1Mo grade ferritic steel. Modifications include additions of vanadium, niobium, and nitrogen, as well as lower carbon content. In this report, we summarized the change of microstructure and mechanical properties after tempering, thermal aging, and irradiation. Modified 9Cr-1Mo steel has high strength and thermal conductivity, low thermal expansion, and good resistance to corrosion. But the irradiation embrittlement behavior of modified 9Cr-1Mo steel should be evaluated and the evaluation methodology also should be developed. At the same time, the characteristics of weldment which is the weak part in pressure vessel should be evaluated.

Phase formation in the Li2MoO4–K2MoO4–In2(MoO4)3 system and crystal structures of new compounds K3InMo4O15 and LiK2In(MoO4)3

International Nuclear Information System (INIS)

Khal’baeva, Klara M.; Solodovnikov, Sergey F.; Khaikina, Elena G.; Kadyrova, Yuliya M.; Solodovnikova, Zoya A.; Basovich, Olga M.

2012-01-01

XRD study of solid-phase interaction in the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system was performed. The boundary K 2 MoO 4 –In 2 (MoO 4 ) 3 system is an non-quasibinary join of the K 2 O–In 2 O 3 –MoO 3 system where a new polymolybdate K 3 InMo 4 O 15 isotypic to K 3 FeMo 4 O 15 was found. In the structure (a=33.2905(8), b=5.8610(1), c=15.8967(4) Å, β=90.725(1)°, sp. gr. C2/c, Z=8, R(F)=0.0407), InO 6 octahedra, Mo 2 O 7 diortho groups and MoO 4 tetrahedra form infinite ribbons {[In(MoO 4 ) 2 (Mo 2 O 7 )] 3− } ∞ along the b-axis. Between the chains, 8- to 10-coordinate potassium cations are located. A subsolidus phase diagram of the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system was constructed and a novel triple molybdate LiK 2 In(MoO 4 ) 3 was revealed. Its crystal structure (a=7.0087(2), b=9.2269(3), c=10.1289(3) Å, β=107.401(1)°, sp. gr. P2 1 , Z=2, R(F)=0.0280) contains an open framework of vertex-shared MoO 4 tetrahedra, InO 6 octahedra and LiO 5 tetragonal pyramids with nine- and seven-coordinate potassium ions in the framework channels. - Graphical abstract: Exploring the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system showed its partial non-quasibinarity and revealed new compounds K 3 InMo 4 O 15 (isotypic to K 3 FeMo 4 O 15 ) and LiK 2 In(MoO 4 ) 3 which were structurally studied. An open framework of the latter is formed by vertex-shared MoO 4 tetrahedra, InO 6 octahedra and LiO 5 tetragonal pyramids. Highlights: ► Subsolidus phase relations in the Li 2 MoO 4 –K 2 MoO 4 –In 2 (MoO 4 ) 3 system were explored. ► The K 2 MoO 4 –In 2 (MoO 4 ) 3 system is a non-quasibinary join of the K 2 O–In 2 O 3 –MoO 3 system. ► New compounds K 3 InMo 4 O 15 and LiK 2 In(MoO 4 ) 3 were obtained and structurally studied. ► K 3 InMo 4 O 15 is isotypic to K 3 FeMo 4 O 15 and carries bands of InO 6 , MoO 4 and Mo 2 O 7 units. ► An open framework of LiK 2 In(MoO 4 ) 3 is formed by polyhedra MoO 4 , InO 6 and LiO 5 .

Symmetrical synergy of hybrid Co9S8-MoSx electrocatalysts for hydrogen evolution reaction

KAUST Repository

Zhou, Xiaofeng

2017-01-07

There exists a strong demand to replace expensive noble metal catalysts with efficient and earth-abundant catalysts for hydrogen evolution reaction (HER). Recently the Co- and Mo-based sulfides such as CoS2, Co9S8, and MoSx have been considered as several promising HER candidates. Here, a highly active and stable hybrid electrocatalyst 3D flower-like hierarchical Co9S8 nanosheets incorporated with MoSx has been developed via a one-step sulfurization method. Since the amounts of Co9S8 and MoSx are easily adjustable, we verify that small amounts of MoSx promotes the HER activity of Co9S8, and vise versa. In other words, we validate that symmetric synergy for HER in the Co- and Mo-based sulfide hybrid catalysts, a long-standing question requiring clear experimental proofs. Meanwhile, the best electrocatalyst Co9S8-30@MoSx/CC in this study exhibits excellent HER performance with an overpotential of −98 mV at −10 mA/cm2, a small Tafel slope of 64.8 mV/dec, and prominent electrochemical stability.

Oxidación parcial de metano a formaldehido sobre catalizadores de MoO3, Fe2O3 y ferromolibdeno

Directory of Open Access Journals (Sweden)

José Daniel Del Río

2007-01-01

Full Text Available Uno de los grandes retos para la catálisis ha sido la conversión directa de metano en productos químicos útiles a la industria tales como metanol y formaldehIdo. Actualmente el formaldehido es producido en un proceso que involucra tres pasos con gas de síntesis y metanol como productos intermedios. En este trabajo se emplearon catalizadores de MoO , Fe O y Fe (MoO en cuatro proporciones Mo/Fe diferentes (0.5, 1, 1.5, 2. El cata-323243 lizador de ferromolibdeno fue preparado por coprecipitación. Los óxidos puros presentan mayor actividad; sin embargo, no son selectivos a formaldehido, siendo los óxidos de carbono (CO, CO los principales productos. Los catalizadores de ferromolibdeno meloran la selectividad a HCHO en detrimento del grado de conversión; el contenido de molibdeno no muestra incrementos en la actividad catalítica. El aumento en la temperatura de reacción no genera un aumento en la selectividad a formaldehido.

Synthesis and IR spectral study of MoO2Cl2 molecular complex with acetoacetanilides. Crystal structure of MoO2Cl2 complex with acetoacet-2-toluidine

International Nuclear Information System (INIS)

Abramenko, V.L.; Sergienko, V.S.; Churakov, A.V.

2000-01-01

Certain MoO 2 Cl 2 complexes with acetoacetanilide derivatives were synthesized, two IR spectral study being performed. Crystal and molecular structure of MoO 2 Cl 2 complex with acetoacet-2-toluidine (HL) was determined using X-ray diffraction analysis. The crystals are monoclinic, a = 7.621 (7), b = 9.498 (3), c = 19.980 (9) A, β = 95.16 (7), Z = 4, sp.gr. P2 1 /n. Coordination polyhedron of Mo atom is a distorted octahedron with two O oxoatoms in cis-position, two Cl atom in mutual trans-position and two O(HL) atoms in trans-positions in reference to O(oxo) [ru

Structural and electrical transport properties of La2Mo2O9 thin films prepared by pulsed laser deposition

Science.gov (United States)

Paul, T.; Ghosh, A.

2017-04-01

We have studied the structure and electrical properties of La2Mo2O9 thin films of different thicknesses prepared by the laser deposition technique at different substrate temperatures. The structural properties of the thin films have been investigated using XRD, XPS, AFM, TEM, SEM, and Raman spectroscopy. The electrical transport properties of the thin films have been investigated in wide temperature and frequency ranges. The cubic nature of the thin films has been confirmed from structural analysis. An enhancement of the oxygen ion conductivity of the films up to five orders of magnitude is obtained compared to that of the bulk La2Mo2O9, suggesting usefulness of the thin films as electrolytes in micro-solid oxide fuel cells. The enhanced dc ionic conductivity of the thin films has been interpreted using the rule of the mixture model, while a power law model has been used to investigate the frequency and temperature dependences of the conductivity. The analysis of the results predicts the three-dimensional oxygen ion conduction in the thin films.

Influencia de la temperatura de austenización y tiempo de permanencia sobre el tamaño de grano en aceros ferrítico-martensíticos del tipo 9Cr1MoVNb utilizados en calderas supercríticas

Directory of Open Access Journals (Sweden)

Gutiérrez-Urrutia, L.

2001-04-01

Full Text Available The aim of the present work is to determine the influence of austenitizing temperature holding time and heating velocity on grain size of ferritic-martensitic type 9CrlMoVNb steels developed for Oak Ridge National Laboratories & Combustion Engineering, T91/P91^[1] Steels (USA and X10CrMoVNb 9.1 (Europe. The potential benefits of this material, in term of high resistance, good ductily and oxidation resistance, weldability and in particular good high temperature creep strength, are now widely acknowledged, particulary by supercritical boilers (P = 300 bar, T = 550±50 °C. The studied steels have been produced in, high frecuency induction vacum furnaces and hot-rolled.

Se estudia la influencia de la temperatura de austenización, tiempo de permanencia a esta temperatura y velocidad de calentamiento sobre el tamaño de grano de varios aceros ferrítico-martensíticos de última generación del tipo 9CrlMoVNb, desarrollados por Oak Ridge National Laboratories (ORNL conjuntamente con Combustion Enginering en USA, conocidos por ASME/ASTM por las designaciones T91/P91^[1] y en Europa como X10CrMoVNb9.1. Son aceros ductiles y tenaces que presentan muy buenas propiedades de resistencia a fluencia, soldabilidad y conductividad térmica. Son cada vez más utilizados como tubos de alta temperatura (550±50 °C y presión (300 bar en calderas supercríticas para centrales térmicas avanzadas. Los aceros estudiados se han fabricado en hornos de inducción de alta frecuencia al vacío y laminados en caliente.

Systems Tl2MoO4-E(MoO4)2, where E=Zr or Hf, and the crystal structure of Tl8Hf(MoO4)6

International Nuclear Information System (INIS)

Bazarov, B.G.; Bazarova, Ts.T.; Fedorov, K.N.; Bazarova, Zh.G.; Chimitova, O.D.; Klevtsova, R.F.; Glinskaya, L.A.

2006-01-01

Systems Tl 2 MoO 4 -E(MoO 4 ) 2 (E=Zr, Hf) were studied by X-ray diffraction, differential thermal analysis and IR spectroscopy. Formation of Tl 8 E(MoO 4 ) 6 and Tl 2 E(MoO 4 ) 2 compounds was established. Phase T-x diagrams of the Tl 2 MoO 4 -Zr(MoO 4 ) 2 system were constructed. Monocrystals were grown, and structure of Tl 8 Hf(MoO 4 ) 6 was studied. The compound is crystallized in monoclinic syngony with elementary cell parameters a=9.9688(6), b=18.830(1), c=7.8488(5) A, β=108.538(1) Deg, Z=2, sp. gr. C2/m. The isolated group [HfMo 6 O 24 ] 8- is responsible for fundamental fragment of the structure. Three varieties of crystallographically independent Tl-polyhedra fill space evenly between fragments [HfMo 6 O 24 ] 8- forming three-dimensional form [ru

Fe--12Ni--4Co--2Mo--.05Ti alloy for use at 770K and below

International Nuclear Information System (INIS)

Whitaker, B.W.

1975-10-01

A variant of the maraging class of steels is proposed for application at 77 0 K and below where a combination of very high strength and good toughness is required. The alloy has a composition of Fe-12Ni-4Co-2Mo-0.05Ti where low interstitial content. The as quenched and quenched and aged structures were completely martensitic with a prior austenitic grain size of 10 to 12 μm. This structure had a Y.S. of 138.5 ksi and 154 ksi before and after aging respectively. All aging was done at 444 0 C for 4 hours. The DBTT was shown to lie above 77 0 K as measured by C/sub v/ testing. Based on dilatometric studies of the α → γ and γ → α transformation temperatures a cycling treatment consisting of reportedly heating to above the A/sub f/ temperature followed by a water quench was utilized to further reduce the prior γ grain size to approximately 4 to 6 μm. The structure was completely martensitic and possessed a Y.S. of 151 ksi at 77 0 K in the unaged condition with a Y.S./K/sub IC/ ratio of 1.9 while the aged structure showed a Y.S. of 162 ksi with a Y.S./K/sub IC/ ratio of 1.3. C/sub v/ testing showed the DBTT to lie between 77 0 K and 4.2 0 K. Further grain refinement was accomplished by a 2 phase decomposition procedure which resulted in a grain size of 1 to 2 μm. The structure which contained decreasing amounts of austenite with temperature (3.0 percent at R.T. to 1.0 percent at 4.2 0 K) showed the best combination of strength and ductility at 4.2 0 K. A Y.S. of 205 ksi with a Y.S./K/sub IC/ ratio of 0.84 was achieved before aging. The aged structure was brittle at 4.2 0 K with a Y.S. of 218 ksi and a Y.S./K/sub IC/ ratio of 0.425

Ordering in rapidly solidified Ni/sub 2/Mo

International Nuclear Information System (INIS)

Kulkarni, U.D.; Dey, G.K.; Banerjee, S.

1988-01-01

Ordering processes in the Ni-Mo system have been a subject of several investigations. Although the ordering behaviour of the Ni/sub 4/Mo and the Ni/sub 3/Mo has been examined in detail, no such study has been reported in the case of the Ni/sub 2/Mo alloy. The lack of experimental work on ordering transformations in Ni/sub 2/Mo is presumably due to the difficulty in obtaining a single phase fcc alloy of this composition. Enhanced solid solubility of Mo in Ni, which accompanies rapid solidification processing (RSP) makes the formation of such a phase possible. The ordering processes in Ni-Mo based alloys show several remarkable features. Firstly, the alloy (15 - 28 at % Mo) quenched from the α -phase filed exhibit a short range order (SRO) characterized by the presence of intensity maxima at /1 1/2 0/ fcc positions of the reciprocal space. This state of SRO has been attributed to the occurrence of 1 1/2 O spinodal ordering in the system. Secondly, the transformation from the state of SRO to the equilibrium/metastable coherent long range ordered (LRO) structures appears to take place in a continuous manner at relatively low temperatures of aging. Three different coherent LRO structures, namely: the equilibrium Ni/sub 4/Mo (prototype structure D1/sub a/) and the metastable Ni/sub 3/Mo (DO/sub 22/) and Ni/sub 2/Mo (Pt/sub 2/Mo) structures have reported to evolve from the SRO alloy, depending upon the aging treatment and the composition of the alloy

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu(3+) phosphors and ceramics.

Science.gov (United States)

Janulevicius, Matas; Marmokas, Paulius; Misevicius, Martynas; Grigorjevaite, Julija; Mikoliunaite, Lina; Sakirzanovas, Simas; Katelnikovas, Arturas

2016-05-16

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu(3+) phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu(3+) showed quantum yields up to 85%, what is suitable for commercial application. Temperature dependent emission spectra revealed that heavily Eu(3+) doped phosphors possess stable emission up to 400 K and lose half of the efficiency only at 515 K. In addition, ceramic disks of Y2Mo4O15:75%Eu(3+) phosphor with thickness of 0.71 and 0.98 mm were prepared and it turned out that they efficiently convert radiation of 375 and 400 nm LEDs to the red light, whereas combination with 455 nm LED yields purple colour.

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu3+ phosphors and ceramics

Science.gov (United States)

Janulevicius, Matas; Marmokas, Paulius; Misevicius, Martynas; Grigorjevaite, Julija; Mikoliunaite, Lina; Sakirzanovas, Simas; Katelnikovas, Arturas

2016-01-01

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu3+ phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu3+ showed quantum yields up to 85%, what is suitable for commercial application. Temperature dependent emission spectra revealed that heavily Eu3+ doped phosphors possess stable emission up to 400 K and lose half of the efficiency only at 515 K. In addition, ceramic disks of Y2Mo4O15:75%Eu3+ phosphor with thickness of 0.71 and 0.98 mm were prepared and it turned out that they efficiently convert radiation of 375 and 400 nm LEDs to the red light, whereas combination with 455 nm LED yields purple colour. PMID:27180941

Synthesis, characterization and thermal stability of solid solutions Zr (Y, Fe, Mo)O {sub 2}

Energy Technology Data Exchange (ETDEWEB)

Legorreta-Garcia, F.; Esperanza Hernandez-Cruz, L.; Villanueva-Ibanez, M.; Flores-Gonzalez, M. A.

2015-10-01

The synthesis of Fe{sup 3}+, Mo{sup 4+} and Y{sup 3+} fully stabilized zirconia by the nitrate/urea combustion route and thermal stability in air was investigated. The solid solution obtained was characterized by X ray diffraction (XRD), scanning electron microscopy (SEM) and used the BET method for determining specific surface. The ceramic powders obtained were calcined at 1473 K in air atmosphere in order to determine their thermal stability. The scanning electron microscopy (SEM) results showed a homogeneous grain surface, measuring several tens of micrometers across. The crystallographic study revealed that by this method it was successfully achieved zirconia doped with Fe{sup 3+}, Mo{sup 4+} and Y{sup 3+} ions in the zirconia tetragonal monophase, even after calcinations. (Author)

Nitrogen Adsorption and Hydrogenation on a MoFe6S9 Complex

DEFF Research Database (Denmark)

Rod, Thomas Holm; Hammer, Bjørk; Nørskov, Jens Kehlet

1999-01-01

The enzyme nitrogenase catalyzes the biological nitrogen fixation where N-2 is reduced to NH3. Density functional calculations are presented of the bonding and hydrogenation of N-2 on a MoFe6S9 complex constructed to model aspects of the active site of nitrogenase. N-2 is found to bind end on to ...... on to one of the Fe atoms. A complete energy diagram for the addition of hydrogen to the MoFe6S9 complex with and without N-2 is given, and a mechanism for ammonia synthesis is proposed on this basis....

Spectroscopic Signatures for Interlayer Coupling in MoS2-WSe2 van der Waals Stacking

Science.gov (United States)

2014-09-07

K. Direct Imaging of Band Profile in Single Layer MoS2 on Graphite: Quasiparticle Energy Gap, Metallic Edge States, and Edge Band Bending. Nano Lett...1403.6455v1. 51. Shi, H.; Pan, H.; Zhang, Y.-W.; Yakobson, B. I. Quasiparticle Band Structures and Optical Properties of Strained Mono- layer MoS2 and WS2...Phys. Rev. B 2013, 87, 155304. 52. Liang, Y.; Huang, S.; Soklaski, R.; Yang, L. Quasiparticle Band-edge Energy and Band Offsets of Monolayer of

Microstructure and properties of MoSi2-MoB and MoSi2-Mo5Si3 molybdenum silicides

International Nuclear Information System (INIS)

Schneibel, J.H.; Sekhar, J.A.

2003-01-01

MoSi 2 -based intermetallics containing different volume fractions of MoB or Mo 5 Si 3 were fabricated by hot-pressing MoSi 2 , MoB, and Mo 5 Si 3 powders in vacuum. Both classes of alloys contained approximately 5 vol.% of dispersed silica phase. Additions of MoB or Mo 5 Si 3 caused the average grain size to decrease. The decrease in the grain size was typically accompanied by an increase in flexure strength, a decrease in the room temperature fracture toughness, and a decrease in the hot strength (compressive creep strength) measured around 1200 deg. C, except when the Mo 5 Si 3 effectively became the major phase. Oxidation measurements on the two classes of alloys were carried out in air. Both classes of alloys were protected from oxidation by an in-situ adherent scale that formed on exposure to high temperature. The scale, although not analyzed in detail, is commonly recognized in MoSi 2 containing materials as consisting mostly of SiO 2 . The MoB containing materials showed an increase in the scale thickness and the cyclic oxidation rate at 1400 deg. C when compared with pure MoSi 2 . However, in contrast with the pure MoSi 2 material, oxidation at 1400 deg. C began with a weight loss followed by a weight gain and the formation of the protective silica layer. The Mo 5 Si 3 containing materials experienced substantial initial weight losses followed by regions of small weight changes. Overall, the MoB and Mo 5 Si 3 additions to MoSi 2 tended to be detrimental for the mechanical and oxidative properties

ESTUDIO DE MEZCLA DE NANOPARTÍCULAS SULFURADAS Y OXIDADAS DE Mo Y DE Ni SOPORTADAS EN ALÚMINA, OBTENIDAS POR EL MÉTODO DE DESCOMPOSICIÓN TÉRMICA

Directory of Open Access Journals (Sweden)

Susana Martínez

2011-01-01

Full Text Available Se sintetizó una mezcla de nanopartículas sulfuradas y oxidadas de Mo y de Ni por el método de descomposición térmica, empleando un sistema de reflujo, dimetil disulfuro como agente sulfidizante, nonano como disolvente y una alúmina comercial que fungía como soporte. El sólido gris resultante se eliminó primero por decantación y luego por evaporación del líquido remanente bajo condiciones de vacío con el fin de evitar cambios, específicamente en las nanopartículas obtenidas. Una vez obtenidas las nanopartículas soportadas en alúmina se determinaron sus propiedades fisicoquímicas (morfología, estructura cristalina, estado de oxidación y composición elemental empleando las técnicas de HR-TEM, XPS e ICP. Los resultados de XPS y MET-HR muestran que el sólido esta conformado por nanopartículas de los metales seleccionados en sus formas oxidadas y sulfuradas tales como MoO3, MoS2, Ni2O3 y NiS, siendo la fase mayoritaria el MoO3. En los resultados no se evidenciaron fases mixtas o aleaciones de Mo y Ni.

First principles calculations of the electronic structure and magnetic properties of Y(Fe,M)9.2 and Y(Fe,M)9.2C (M= Si, Ga, Zr)

Science.gov (United States)

Tian, Guang; Zha, Liang; Yang, Wenyun; Qiao, Guanyi; Wang, Changsheng; Yang, Yingchang; Yang, Jinbo

2018-06-01

The preferential site substitution of the Fe by Si, Ga and Zr in the Y(Fe,M)9.2 and Y(Fe,M)9.2C compounds, and the doping effects on the magnetic properties have been studied by the first-principles calculations. It is found that the doping of the Si or Zr can improve the thermodynamic stability of the 1:9 phase, while the substitution of the Fe by Ga makes it unstable. Si atom tends to enter the 3g crystal site and Zr prefers to occupy the 2e site when Y(Fe,M)9.2 and their carbides are synthesized. Although the substitution of the Fe by Si and Zr will reduce the total magnetic moments of the YFe9.2 and their carbides, the volumetric and the d-band narrowing effects caused by the doping can still modify the electron density distributions of the Fe near the Fermi level, improving the magnetic ordering temperature of the non-carbonated compound YFe9.2. The calculated magnetic ordering temperatures of Y(Fe,M)9.2C decrease with the increasing content of the doping elements M due to the stronger hybridization of the d bands in the carbides. For the rare-earth(RE) iron based intermetallics REFe9.2 with the TbCu7-type structure, it is suggested that Zr is able to stabilize the phase and enhance the magnetic ordering temperature, indicating the possible further application in the field of permanent magnets, which has not been reported before.

Measurement of formation cross-section of 99Mo from the 98Mo(n,γ) and 100Mo(n,2n) reactions.

Science.gov (United States)

Badwar, Sylvia; Ghosh, Reetuparna; Lawriniang, Bioletty M; Vansola, Vibha; Sheela, Y S; Naik, Haladhara; Naik, Yeshwant; Suryanarayana, Saraswatula V; Jyrwa, Betylda; Ganesan, Srinivasan

2017-11-01

The formation cross-section of medical isotope 99 Mo from the 98 Mo(n,γ) reaction at the neutron energy of 0.025eV and from the 100 Mo(n,2n) reaction at the neutron energies of 11.9 and 15.75MeV have been determined by using activation and off-line γ-ray spectrometric technique. The thermal neutron energy of 0.025eV was used from the reactor critical facility at BARC, Mumbai, whereas the average neutron energies of 11.9 and 15.75MeV were generated using 7 Li(p,n) reaction in the Pelletron facility at TIFR, Mumbai. The experimentally determined cross-sections were compared with the evaluated nuclear data libraries of ENDF/B-VII.1, CENDL-3.1, JENDL-4.0 and JEFF-3.2 and are found to be in close agreement. The 100 Mo(n,2n) 99 Mo reaction cross-sections were also calculated theoretically by using TALYS-1.8 and EMPIRE-3.2 computer codes and compared with the experimental data. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phase formation in the K2MoO4-Lu2(MoO4)3-Hf(MoO4)2 system and the structural study of triple molybdate K5LuHf(MoO4)6

International Nuclear Information System (INIS)

Romanova, E.Yu.; Bazarov, B.G.; Tushinova, Yu.L.; Fedorov, K.N.; Bazarova, Zh.G.; Klevtsova, R.F.; Glinskaya, L.A.

2007-01-01

Interactions in the ternary system K 2 MoO 4 -Lu 2 (MoO 4 ) 3 -Hf(MoO 4 ) 2 have been studied by X-ray powder diffraction and differential thermal analysis. A new triple (potassium lutetium hafnium) molybdate with the 5 : 1 : 2 stoichiometry has been found. Monocrystals of this molybdate have been grown. Its X-ray diffraction structure has been refined (an X8 APEX automated diffractometer, MoK α radiation, 1960 F(hkl), R = 0.0166). The trigonal unit cell has the following parameters: a = 10.6536(1) A, c = 37.8434(8) A, V=3719.75(9) A, Z = 6, space group R3-bar c. The mixed 3D framework of the structure is built of Mo tetrahedra sharing corners with two independent (Lu,Hf)O 6 octahedra. Two sorts of potassium atoms occupy large framework voids [ru

Fracture behavior of unirradiated HT-9 and modified 9Cr-1Mo welds

International Nuclear Information System (INIS)

Huang, F.H.; Gelles, D.S.

1983-05-01

Fracture toughness tests on HT-9 weld and HAZ samples and modified 9Cr-1Mo weld samples were performed at 93, 205, 427 and 538 0 C. Specimens were of circular compact tension type fabricated from welded material with the notch orientation parallel to the fusion line. The test results were analyzed using the J-integral approach. The results demonstrated that the toughness of HT-9 and 9Cr-1Mo was not significantly reduced due to welding. However, the tearing modulus of the welded material was lower than that of base metal, indicating that the alloys become less resistant to crack propagation as a result of welding

Enhanced Selectivity and Uptake Capacity of CO2 and Toluene Adsorption in Co0.5 M0.33 MoS4 (M= Sb or Y) Chalcogels by Impregnated Metal Salts

KAUST Repository

Edhaim, Fatimah A.; Rothenberger, Alexander

2017-01-01

The synthesis of metal chalcogenide aerogels Co0.5M0.33MoS4 (M= Sb or Y) by the sol-gel method is reported. In this system, the building blocks [MoS4]2− chelated with Co2+ and (Sb3+) or (Y3+) salts in nonaqueous solvents forming amorphous networks

Concentration-dependent luminescence and energy transfer of flower-like Y2(MoO4)3:Dy3+ phosphor

International Nuclear Information System (INIS)

Tian Yue; Chen Baojiu; Tian Bining; Hua Ruinian; Sun Jiashi; Cheng Lihong; Zhong Haiyang; Li Xiangping; Zhang Jinsu; Zheng Yanfeng; Yu Tingting; Huang Libo; Meng Qingyu

2011-01-01

Highlights: → Flower-shaped Y 2 (MoO 4 ) 3 phosphors were prepared by a co-precipitation method. → The structure and morphology of the prepared phosphors were characterized. → Energy transfer between Dy 3+ was studied by Huang's theory, IH and Uitert's models. - Abstract: Flower-like Y 2 (MoO 4 ) 3 :Dy 3+ phosphors have been synthesized via a co-precipitation approach with the aid of β-cyclodextrin. The crystal structure and morphology of the phosphors were characterized by XRD (X-ray diffraction) and FE-SEM (field emission scanning electron microscopy), respectively. The excitation and emission properties of the phosphors were examined by fluorescence spectroscopy. The dependence of color coordinates on the Dy 3+ doping concentration was analyzed. The energy transfer mechanism between Dy 3+ ions was studied based on the Huang's theory, I-H and Van Uitert's models. It was concluded simultaneously from these three routes that the electric dipole-dipole interaction between Dy 3+ ions is the main physical mechanism for the energy transfers between Dy 3+ .

Irradiation hardening of Mod.9Cr-1Mo steel

International Nuclear Information System (INIS)

Ryu, Woo-Seog; Kim, Sung-Ho; Choo, Kee-Nam; Kim, Do-Sik

2009-01-01

An irradiation test of Mod.9Cr-1Mo steel was carried out in the OR5 test hole of HANARO of a 30 MW thermal power at 390±10degC up to a fast neutron fluence of 4.4x10 19 (n/cm 2 ) (E > 1.0 MeV). The dpa of the irradiated specimens was evaluated to be 0.034 - 0.07. Tensile and impact tests of the irradiated Mod.9Cr-1Mo were done in the hot cell of the IMEF. The change of the tensile strength by irradiation was similar to the change of the yield strength. The increase of the yield and tensile strengths was up to 18% and 10% respectively. The elongation reduction of the weldment was up to 65%. (author)

Microstructural study on gamma phase stability in U-9 wt% Mo alloy system

International Nuclear Information System (INIS)

Saify, M.T.; Jha, S.K.; Hussain, M.M.; Singh, R.P.; Neogy, S.; Srivastava, D.; Dey, G.K.

2009-01-01

water, the gamma phase got stabilized and retained at room temperature in the metastable state. Even furnace cooling after homogenization did not lead to the loss of the retained bcc lattice of the gamma solid solution. The homogenizing annealing also influenced the eutectoid decomposition of the metastable gamma phase into and γ' (U 2 Mo) phases. Under the same ageing conditions (500 deg C /5 days) the extent of decomposition was found to be more in case of the as rolled sample as compared to the homogenized sample. The homogenized sample that was aged for 14 days at 500 deg C showed almost complete decomposition of the γ phase. The microstructure also showed coarsening of the α and γ' lamellas in many colonies. XRD examination and optical microscopy showed that Mo content to the tune of 9 wt% in the alloy resulted in stiffening of the U lattice, making it difficult for the transformations to take place. (author)

Thermal expansion of Cr2xFe2-2xMo3O12, Al2xFe2-2xMo3O12 and Al2xCr2-2xMo3O12 solid solutions

International Nuclear Information System (INIS)

Ari, M.; Jardim, P.M.; Marinkovic, B.A.; Rizzo, F.; Ferreira, F.F.

2008-01-01

The transition temperature from monoclinic to orthorhombic and the thermal expansion of the orthorhombic phase were investigated for three systems of the family A 2 M 3 O 12 : Cr 2x Fe 2-2x Mo 3 O 12 , Al 2x Fe 2-2x Mo 3 O 12 and Al 2x Cr 2-2x Mo 3 O 12 . It was possible to obtain a single-phase solid solution in all studied samples (x=0, 0.1, 0.3, 0.5, 0.7, 0.9 and 1). A linear relationship between the transition temperature and the fraction of A 3+ cations (x) was observed for each system. In all orthorhombic solid solutions studied here the observed thermal expansion was anisotropic. These anisotropic thermal expansion properties of crystallographic axes a, b and c result in a low positive or near-zero overall linear coefficient of thermal expansion (α l =α V /3). The relationship between the size of A 3+ cations in A 2 M 3 O 12 and the coefficient of thermal expansion is discussed. Near-zero thermal expansion of Cr 2 Mo 3 O 12 is explained by the behavior of Cr-O and Mo-O bond distances, Cr-Mo non-bond distances and Cr-O-Mo bond angles with increasing temperature, estimated by Rietveld analysis of synchrotron X-ray powder diffraction data. - Graphical abstract: In this figure, all published overall linear coefficients of thermal expansion for orthorhombic A 2 M 3 O 12 family obtained through diffraction methods as a function of A 3+ cation radii size, together with dilatometric results, are plotted. Our results indicate that Cr 2 Mo 3 O 12 does not exactly follow the established relationship

Isothermal section of diagram of U-Mo-B and U-Re-B systems

International Nuclear Information System (INIS)

Val'ovka, I.P.; Kuz'ma, Yu.B.

1986-01-01

The methods of X-ray analysis are used to study the U-Mo-B and U-Re-B systems and to plot phase equilibrium diagrams at 1000 and 800 deg C, respectively. A formation of boride UMoB 4 (structure of the ThMoB 4 type) is confirmed in the U-Mo-B system and new compounds are found: U 2 MoB 6 (rhombic structure of the Y 2 ReB 6 type, a=0.9301(9), b=1.1434(11), c=0.3678(4) nm), ∼UMo 2 B 6 and ∼ UMo 4 B 4 with unknown structures. In the U-Re-B system besides previously known boride UReB 4 (the ThMoB 4 structure type), new ones are obtained: U 2 ReB 6 (Y 2 ReB 6 type, a=0.9373(9), b=1.1529(13), c0.3653(4) nm) and UReB 3 (hexagonal structure of the proper type, a=0.5083(1), c=0.5095(1) nm)

Postirradiation notch ductility tests of ESR alloy HT-9 and modified 9Cr-1Mo alloy from UBR reactor experiments

International Nuclear Information System (INIS)

Hawthorne, J.R.

1984-01-01

During this period, irradiation exposures at 300 0 C and 150 0 C to approx. 8 x 10 19 n/cm 2 , E > 0.1 MeV, were completed for the Alloy HT-9 plate and the modified Alloy 9Cr-1Mo plates, respectively. Postirradiation tests of Charpy-V (C/sub v/) specimens were completed for both alloys; other specimen types included in the reactor assemblies were fatigue precracked Charpy-V (PCC/sub v/), half-size Charpy-V, and in the case of the modified 9Cr-1Mo, 2.54 mm thick compact tension specimens

Influência do teor de Mo na microestrutura de ligas Fe-9Cr-xMo Effect of the content of molybdenum in the microstructure of Fe-9Cr-xMo alloy

Directory of Open Access Journals (Sweden)

Rodrigo Freitas Guimarães

2010-12-01

Full Text Available Aços Cr-Mo são usados na indústria do petróleo em aplicações com óleos crus ricos em compostos sulfurosos. Aços comerciais como 2.5Cr1Mo ou 9Cr1Mo têm se mostrado ineficientes em consequência de altos índices de corrosão naftênica. Uma estratégia para resolver este problema é o aumento do teor de molibdênio destes aços. Neste trabalho foi estudado o efeito do aumento do teor de molibdênio na microestrutura de ligas Fe-9Cr-xMo, solubilizadas e soldadas. Foram levantados os diagramas de fases com auxílio de um programa comercial para verificar as possíveis fases a serem formadas e identificar os problemas de soldagem. A microestrutura das ligas solubilizadas foi analisada por microscopia óptica e EBSD, além da medição da dureza. Foram realizadas soldagens autógenas para verificar o efeito do aporte térmico na microestrutura e na dureza das ligas. O aumento do teor de molibdênio resultou no aumento da dureza das ligas. A análise microestrutural das ligas soldadas apresentou uma particularidade para a liga com menor teor de molibdênio, a presença de martensita. Já as ligas com maior teor de molibdênio apresentaram uma microestrutura completamente ferrítica. A formação de martensita pode ser um problema na solda da liga com menor teor de molibdênio, uma vez que a mesma pode causar perdas nas propriedades mecânicas comprometendo sua aplicação.Cr-Mo steels are used in the petroleum industry in applications with crude oils rich in sulfur compounds. 2.5Cr1Mo or 9Cr1Mo do not resist to operating conditions when in contact with crude oils. The increasing of molybdenum content can improve the corrosion resistance of these alloys. This paper studied the effect of increased concentration of molybdenum in the microstructure of Fe-9Cr-xMo alloys, annealed and welded. Phase diagrams were built with the aid of commercial program to check the possible phases to be formed and to identify the problems of welding. Analyses were

Breastfeeding and complementary feeding in relation to body mass index and overweight at ages 7 and 11 y

DEFF Research Database (Denmark)

Morgen, Camilla Schmidt; Ängquist, Lars; Baker, Jennifer Lyn

2018-01-01

associations with overweight. Results: Duration of BF was not associated with childhood BMIz at ages 7 and 11 y. Earlier introduction of complementary food (4 mo old) was not associated with BMIz at age 7 y, but with a 0.069 (95% CI: 0.021, 0.117, P = 0.005) higher BMIz at age 11 y and increased risk...

Motor Proficiency of 6- to 9-Year-Old Children with Speech and Language Problems

Science.gov (United States)

Visscher, Chris; Houwen, Suzanne; Moolenaar, Ben; Lyons, Jim; Scherder, Erik J. A.; Hartman, Esther

2010-01-01

Aim: This study compared the gross motor skills of school-age children (mean age 7y 8mo, range 6-9y) with developmental speech and language disorders (DSLDs; n = 105; 76 males, 29 females) and typically developing children (n = 105; 76 males, 29 females). The relationship between the performance parameters and the children's age was investigated…

Sign system choice influence on the substance formation forecast in A2MoO4-B2(MoO4)3 and A2MoO4-CMoO4 systems

International Nuclear Information System (INIS)

Manzanov, Yu.E.; Lutsik, V.I.; Mokhosoev, M.V.

1987-01-01

Three sign spaces were used for forecasting compound formation in A 2 MoO 4 -B 2 (MoO 4 ) 3 (5:1 ratio, where A-Li, Na, K, Rb, Cs; B-Al, In, Ga, Sc, Cr, Fe, Bi, La, Nd, Sm-Lu, Y) and A 2 MoO 4 -CMoO 4 (1:2 ratio, where A-Li, Na, K, RB, Cs, Tl; C-Mg, Ca, Sr, Ba, Cu, Zn, Cd, Pd, Mn, Co, Ni) systems: 1-electron distribution on energy shells of cations and their valency; 2-the type of incomplete electron shell, charge of cations, three first ionization potentials, standard heat capacity, ionic radius of cations; 3-standard formation enthalpy and standard entropy, oxide melting points and ionic radius of cations. It is shown that sign space, related with thermodynamic properties of oxides contains data, necessary for forecasting interaction in molybdate systems. This enables to improve reliability of forecasting

Synthesis of coaxial nanotubes of MoS{sub 2} and carbon; Sintesis de nanotubos coaxiales de MoS{sub 2} y Carbono

Energy Technology Data Exchange (ETDEWEB)

Reza, C; Perez, M; Santiago, P [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2002-07-01

The di chalcogenides WS{sub 2} and MoS{sub 2} by their tubular properties were combined. It was synthesized coaxial structures of MoS{sub 2} with C with the purpose to studying the possible structural changes of the MoS{sub 2} nano tubes at was submitted to a propylene gas flux as carbon precursor in a thermal treatment. Studies of structural characterization by Transmission Electron Microscopy (Tem) were realized. The theoretical simulation of the structure was realized using an algorithm type multilayer. The possibility of the nano tubes are applied to gas storage as can be the hydrogen arouse interest by the energy production. (Author)

Characterization of the interaction layer in diffusion couples U-Mo-Zr/Al and U-Mo-Zr/Al-A356 at 550 C degrees; Caracterizacion de la zona de interaccion en pares de difusion a 550 grados C U-Mo-Zr/Al y U-Mo-Zr/Al-A356

Energy Technology Data Exchange (ETDEWEB)

Komar Varela, Carolina; Arico, Sergio; Mirandou, Marcela; Balart, Silvia; Gribaudo, Luis [Comision Nacional de Energia Atomica, General San Martin (Argentina). Dept. de Materiales; com, carolinakomar@gmail

2007-07-01

Out-of-pile diffusion experiments were performed between U-7 wt.% Mo-1 wt.% Zr and Al or Al A356 (7,1 wt.% Si) at 550 C degrees. In this work morphological characterization and phase identification on both interaction layers are presented. They were carried out by the use of different techniques: optical and scanning electron microscopy, X-ray diffraction and WDS microanalysis. In the interaction layer U-7 wt.% Mo-1 wt.% Zr/Al, the phases UAl{sub 3}, UAl{sub 4}, Al{sub 20}Mo{sub 2}U and Al{sub 43}Mo{sub 4}U{sub 6} were identified. Similar results in the interaction layer of the U-7 % Mo/Al at 580 C degrees were previously obtained. In the interaction layer U-7 wt.% Mo-1 wt.% Zr/Al A356, the phases U(Al,Si){sub 3} with 25 at.% Si and Si{sub 5}U{sub 3} were identified. This last phase, with a higher Si concentration, was identified with X-ray diffraction synchrotron radiation performed at the National Synchrotron Light Laboratory, Campinas, Brazil. (author) [Spanish] Se realizaron experiencias fuera de reactor en pares de difusion quimica U-7 % Mo-1 % Zr/Al y U-7 % Mo-1 % Zr/Al A356. En este trabajo se presentan los resultados de la caracterizacion morfologica e identificacion de fases presentes en la zona de interaccion que se forma al ser sometidos a un tratamiento isotermico de 1,5 h a 550 grados C. Las tecnicas utilizadas fueron: microscopia optica y electronica de barrido, difraccion de rayos X y microanalisis cuantitativo por sonda electronica. En la zona de interaccion correspondiente al par U-7 % Mo-1 % Zr/Al se identificaron las fases UAl{sub 3}, UAl{sub 4}, Al{sub 20}Mo{sub 2}U y Al{sub 43}Mo{sub 4}U{sub 6}. Estas cuatro fases fueron identificadas en pares U-7 % Mo/Al a 580 grados C en trabajos anteriores. En la zona de interaccion correspondiente al par U-7 % Mo-1 % Zr/Al A356 se identificaron las fases U(Al,Si){sub 3} (con una concentracion de 25 %at.Si) y Si{sub 5}U{sub 3}. Este compuesto rico en Si solo pudo ser identificado mediante la utilizacion de

Substitution of modified 9 Cr-1 Mo steel for austentic stainless steels

International Nuclear Information System (INIS)

Sikka, V.K.

1982-04-01

This report describes the current program to develop a high-strength ferritic-martensitic steel. The alloy is essentially Fe-9% Cr-1% Mo with small additions of V and Nb and is known as modifed 9 Cr-1 Mo steel. Its elevated-temperature properties and design allowable stresses match those of type 304 stainless steel for temperatures up to 600 0 C and exceed those of other ferritic steels by factors of 2 to 3. The improved strength of this alloy permits its use in place of stainless steels for many applications

Effect of Mo concentration and aging time on the magnetic and mechanical hardness of Fe-xMo-5Ni-0.05C alloys (x = 5, 8, 11 and 15 wt. (%

Directory of Open Access Journals (Sweden)

Mauro Carlos Lopes Souza

2009-01-01

Full Text Available Changes to the microestructure during thermal aging treatment at 610 ºC in Fe-xMo-5Ni-0.05C alloys were studied for different aging times with different Mo concentrations. The heat treatment at 610 ºC induces carbide precipitation into the metallic matrix near Fe2Mo phase. The X-ray diffraction studies revealed a more intense precipitation of α-FeMo, Fe3Mo, R(Fe63Mo37 phases and MoC, Fe2MoC carbides for the alloys containing 15 and 11% Mo, respectively. This work shows that hardness and coercive force changes are function of the molybdenum content and aging time variation. Vickers hardness and coercive force both increase with the increase of molybdenum content and reach maximum values at 4 and 1h of aging, respectively.

Growth and spectroscopic properties of Er{sup 3+}-doped Li{sub 3}Ba{sub 2}Y{sub 3}(MoO{sub 4}){sub 8} crystal

Energy Technology Data Exchange (ETDEWEB)

Song Mingjun, E-mail: smj521@hotmail.com [College of Chemistry and Chemical Engineering, Weifang University, Weifang, Shandong 261061 (China); Wang Lintong [College of Chemistry and Chemical Engineering, Weifang University, Weifang, Shandong 261061 (China); Zhao Wang [Department of Physics, Huainan Normal University, Huainan, Anhui 232001 (China); Wang Guofu [Fujian Institute of Research on the Structure of Matter, The Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Zhao Meili; Meng Qingguo [College of Chemistry and Chemical Engineering, Weifang University, Weifang, Shandong 261061 (China)

2011-06-15

Highlights: > Er{sup 3+}:Li{sub 3}Ba{sub 2}Y{sub 3}(MoO{sub 4}){sub 8} crystal was grown by the top seeded solution growth method and the appearance and composition of the crystal were analyzed. > The spectroscopic parameters were calculated based on the Judd-Ofelt theory. > The lifetime of the crystal and powder sample was measured and the radiation trapping effect was discussed. > The up-conversion fluorescence spectra were measured and the possible up-conversion mechanisms were proposed. - Abstract: Er{sup 3+}:Li{sub 3}Ba{sub 2}Y{sub 3}(MoO{sub 4}){sub 8} crystal has been grown by the top seeded solution growth method (TSSG) from a flux of Li{sub 2}MoO{sub 4} and its morphology was analyzed. The polarized absorption spectra, fluorescence spectra and fluorescence decay curves of the crystal were measured. Based on the Judd-Ofelt (J-O) theory, spectroscopic parameters of Er{sup 3+}:Li{sub 3}Ba{sub 2}Y{sub 3}(MoO{sub 4}){sub 8} crystal, including the oscillator intensity parameters {Omega}{sub t} (t = 2, 4, 6), spontaneous emission probabilities, fluorescence branching ratios, and radiative lifetimes were calculated and analyzed. Stimulated emission cross-sections of the {sup 4}I{sub 13/2} {yields} {sup 4}I{sub 15/2} transition were estimated by the reciprocity method (RM) and the Fuchtbauer-Ladenburg (F-L) formula. Five up-conversion fluorescence bands around 490, 530, 550, 660 and 800 nm were observed with 977 nm excitation, and the possible up-conversion mechanisms were proposed.

Mechanical properties of steel 8 CrMoNiNb 9 10 in dependence on the microstructural condition

International Nuclear Information System (INIS)

Fabritius, H.; Schnabel, E.

1976-01-01

Tension tests at room temperature to 600 0 C and creep-rupture tests at 500 to 600 0 C lasting up to about 75,000 h on two casts of steel 8 CrMoNiNb 9 10 with about 0.08% C, 0.3% Si, 0.7% Mn, 0.012% N, 0.005% Al, 2.34% Cr, 0.95% Mo, 0.8% Nb and 0.64% Ni in bainitic and ferritic microstructural condition. Influence of annealing at 650 to 800 0 C on the properties in the tension test. Influence of aging at 500 to 600 0 C lasting up to 30,000 h with and without mechanical stress on the properties in the tension test at aging temperature and on the toughness behaviour in the notched bar impact bend test at room temperature. (orig.) [de

Phase relations in the M2MoO4 - Ag2MoO4 - Hf(MoO4)2 (M=Li, Na) systems

International Nuclear Information System (INIS)

Bazarova, Zh.G.; Bazarov, B.G.; Balsanova, L.V.

2002-01-01

The M 2 MoO 4 - Ag 2 MoO 4 - Hf(MoO 4 ) 2 (M=Li, Na) systems were studied by X-ray diffraction and differential thermal analyses in the subsolidus area (450 - 500 Deg C) for the first time. The formation of the binary compound with the variable composition Li 4-x Hf 1+0.2x (MoO 4 ) 4 (0 ≤ x ≤ 0.6) in the Li 2 MoO 4 - Hf(MoO 4 ) 2 system and the ternary molybdates Li 4 Ag 2 Hf(MoO 4 ) 5 (S 1 ) and Na 2 Ag 2 Hf(MoO 4 ) 4 (S 2 ) was established and the thermal characteristics of the prepared compounds were examined. The new binary molybdate Ag 2 Hf(MoO 4 ) 3 was prepared by the reaction between Ag 2 MoO 4 and Hf(MoO 4 ) 2 [ru

Impact of reduced graphene oxide on MoS{sub 2} grown by sulfurization of sputtered MoO{sub 3} and Mo precursor films

Energy Technology Data Exchange (ETDEWEB)

Pacley, Shanee, E-mail: shanee.pacley@us.af.mil; Brausch, Jacob; Beck-Millerton, Emory [U.S. Air Force Research Laboratory (AFRL)/Wright Patterson Air Force Base, Wright Patterson, Ohio 45433-7707 (United States); Hu, Jianjun; Jespersen, Michael [University of Dayton Research Institute, 300 College Park, Dayton, Ohio 45469 (United States); Hilton, Al [Wyle Laboratories, 4200 Colonel Glenn Hwy, Beavercreek, Ohio 45431 (United States); Waite, Adam [University Technology Corporation, 1270 N Fairfield Rd., Beavercreek, Ohio 45432 (United States); Voevodin, Andrey A. [Department of Materials Science and Engineering, University of North Texas, 1155 Union Circle, Denton, Texas 76203 (United States)

2016-07-15

Monolayer molybdenum disulfide (MoS{sub 2}), a two dimensional semiconducting dichalcogenide material with a bandgap of 1.8–1.9 eV, has demonstrated promise for future use in field effect transistors and optoelectronics. Various approaches have been used for MoS{sub 2} processing, the most common being chemical vapor deposition. During chemical vapor deposition, precursors such as Mo, MoO{sub 3}, and MoCl{sub 5} have been used to form a vapor reaction with sulfur, resulting in thin films of MoS{sub 2}. Currently, MoO{sub 3} ribbons and powder, and MoCl{sub 5} powder have been used. However, the use of ribbons and powder makes it difficult to grow large area-continuous films. Sputtering of Mo is an approach that has demonstrated continuous MoS{sub 2} film growth. In this paper, the authors compare the structural properties of MoS{sub 2} grown by sulfurization of pulse vapor deposited MoO{sub 3} and Mo precursor films. In addition, they have studied the effects that reduced graphene oxide (rGO) has on MoS{sub 2} structure. Reports show that rGO increases MoS{sub 2} grain growth during powder vaporization. Herein, the authors report a grain size increase for MoS{sub 2} when rGO was used during sulfurization of both sputtered Mo and MoO{sub 3} precursors. In addition, our transmission electron microscopy results show a more uniform and continuous film growth for the MoS{sub 2} films produced from Mo when compared to the films produced from MoO{sub 3}. Atomic force microscopy images further confirm this uniform and continuous film growth when Mo precursor was used. Finally, x-ray photoelectron spectroscopy results show that the MoS{sub 2} films produced using both precursors were stoichiometric and had about 7–8 layers in thickness, and that there was a slight improvement in stoichiometry when rGO was used.

4s24p3--4s4p4 and 4s24p3--4s2fp25s transitions in Y VII, Zr VIII, Nb IX, and MoX

International Nuclear Information System (INIS)

Reader, J.; Acquista, N.

1981-01-01

Spectra of ionized Y, Zr, Nb, and Mo have been observed in sliding-spark and triggered-spark discharges on 10.7-m normal- and grazing-incidence spectrographs at the National Bureau of Standards in Washington, D. C. From these observations the 4s 2 4p 3 --4s4p 4 transitions in Y VII, Zr VIII, Nb IX, and Mo X have been identified. The 4s 2 4p 3 --4s 2 4p 2 5s transitions in Y VII-Mo X, previously identified by Rahimullah et al. [Phys. Scr. 14, 221--223 (1976); 18, 96--106 (1978)], have been confirmed. In Y VII the 4s 2 4p 3 --4s 2 4p 2 6s and 4s4p 4 --4p 5 transition also have been found. The parameters obtained from least-squares fits to the energy levels are compared with Hartree--Fock calculations. Preliminary values of the ionization energies have been determined as 110.02 +- 0.15 eV for Y VII, 133.7 +- 0.5 eV for Zr VIII, 159.2 +- 0.7 eV for Nb IX, and 186.4 +- 1.2 eV for Mo X

Effect of rare earth elements yttrium and lanthanum on high temperature oxidation resistance of Mo-Si-B alloys

International Nuclear Information System (INIS)

Majumdar, Sanjib

2014-01-01

In the present investigation, 0.2 to 2 at% Y and La alloyed Mo-9Si-8B were consolidated using mechanical alloying followed by spark plasma sintering. Isothermal oxidation studies were conducted in a wide temperature range from 650 to 1300℃. Detailed characterization studies of the oxide scale using SEM, EDS, FIB, TEM reveal the formation of Y x Mo 18 O 32 and 3La 2 O 3 ·MoO 3 oxide phases, respectively, for Y and La-containing alloys reduce the evaporation of MoO 3 . The growth rate of protective silica scale is also enhanced due to faster formation of Y and La rich oxide particles which probably act as nucleation sites for silica. At higher temperatures (at 1100℃), the oxidation behavior of unalloyed and RE-alloyed Mo-9Si-8B are comparable. A transient weight loss followed by a steady state is reached due to protective amorphous silica-rich scale formation beyond 1100℃. Therefore, alloying with rare earth elements provides a broader application temperature window for silicide based materials starting from 750℃ to 1300℃

Smart Aging Platform for Evaluating Cognitive Functions in Aging: A Comparison with the MoCA in a Normal Population

Directory of Open Access Journals (Sweden)

Sara Bottiroli

2017-11-01

Full Text Available Background: Smart Aging is a Serious games (SGs platform in a 3D virtual environment in which users perform a set of screening tests that address various cognitive skills. The tests are structured as 5 tasks of activities of daily life in a familiar environment. The main goal of the present study is to compare a cognitive evaluation made with Smart Aging with those of a classic standardized screening test, the Montreal Cognitive Assessment (MoCA.Methods: One thousand one-hundred thirty-one healthy adults aged between 50 and 80 (M = 64.3 ± 8.3 were enrolled in the study. They received a cognitive evaluation with the MoCA and the Smart Aging platform. Participants were grouped according to their MoCA global and specific cognitive domain (i.e., memory, executive functions, working memory, visual spatial elaboration, language, and orientation scores and we explored differences among these groups in the Smart Aging indices.Results: One thousand eighty-six older adults (M = 64.0 ± 8.0 successfully completed the study and were stratified according to their MoCA score: Group 1 with MoCA < 27 (n = 360; Group 2 with 27 ≥ MoCA < 29 (n = 453; and Group 3 with MoCA ≥ 29 (n = 273. MoCA groups significantly differed in most of the Smart Aging indices considered, in particular as concerns accuracy (ps < 0.001 and time (ps < 0.001 for completing most of the platform tasks. Group 1 was outperformed by the other two Groups and was slower than them in these tasks, which were those supposed to assess memory and executive functions. In addition, significant differences across groups also emerged when considering the single cognitive domains of the MoCA and the corresponding performances in each Smart Aging task. In particular, this platform seems to be a good proxy for assessing memory, executive functions, working memory, and visual spatial processes.Conclusion: These findings demonstrate the validity of Smart Aging for assessing cognitive functions in normal

On the coexistence of copper-molybdenum bronzes: CuxMoO₃ (0.2 < x < 0.25; typically x = 0.23) and CuyMoO_3-z (0.1 < y < 0.2; typically y = 0.15) in the Cu-MoO₂-O quasi-ternary system

DEFF Research Database (Denmark)

Warner, Terence Edwin; Skou, Eivind Morten

2010-01-01

Two copper-molybdenum bronzes: CuyMoO3-z (0.1black polycrystalline materials by the solid state reaction of Cu and MoO3 at 600 C under argon in Pt crucibles. Powder XRD showed that the material...... with global composition ‘0.1Cu.MoO3’ comprises ~Cu0.15MoO3 and MoO3; whilst ‘0.2Cu.MoO3’ comprises ~Cu0.15MoO3 and ~Cu0.23MoO3. DTA performed on ‘0.2Cu.MoO3’ reveals a reversible solid state phase transition = 520 C under argon. Reacting equimolar amounts of Cu2O and MoO2 at 600 C in a Cu crucible under argon...

Effect of vitamin A supplementation with BCG vaccine at birth on vitamin A status at 6 wk and 4 mo of age

DEFF Research Database (Denmark)

Fisker, Ane B; Lisse, Ida M; Aaby, Peter

2007-01-01

concentrations indicated vitamin A deficiency in 32% of the children at age 6 wk and in 16% at age 4 mo. VAS was not associated with higher RBP concentrations overall or in either sex. However, the effect of VAS varied with maternal education (P for interaction = 0.004): At age 6 wk, VAS was associated...... with higher (9%; 95% CI: 2, 17%) RBP concentrations in children of noneducated mothers but not in children of educated mothers. Overall, RBP concentrations increased between 6 wk and 4 mo of age. The increase correlated inversely with the number of diphtheria-tetanus-pertussis (DTP) vaccines received...... placebo-controlled trial of VAS, we obtained blood from 614 children at 6 wk of age and from 369 mother-infant pairs at 4 mo of age. We assessed vitamin A status on the basis of serum retinol-binding protein (RBP) and measured serum C-reactive protein to monitor for concurrent infections. RESULTS: RBP...

Synthesis and characterization of environmentally benign calcium-doped Pr2Mo2O9 pigments: Applications in coloring of plastics

International Nuclear Information System (INIS)

George, Giable; Sandhya Kumari, L.; Vishnu, V.S.; Ananthakumar, S.; Reddy, M.L.P.

2008-01-01

A new class of environmentally benign rare earth pigments of general formula Pr 2-x Ca x Mo 2 O 9-δ (x ranges from 0 to 1.0) displaying colors ranging from green to yellow were synthesized by traditional solid-state route, as alternatives to lead, cadmium and chromium colorants. The products were characterized by X-ray powder diffraction, UV-vis spectroscopy and CIE-L*a*b* 1976 color scales. The coloring mechanism is based on the strong absorptions of the pigments in the blue and red regions due to electronic transitions between 4f 2 →4f 1 5d 1 states of Pr 3+ . The designed pigments consist of non-toxic elements and further found to be thermally and chemically stable. The yellow-green pigments were found to be interesting alternatives to existing toxic pigments for coloration of plastics. - Graphical abstract: A new class of environmentally benign rare earth pigments of general formula Pr 2-x Ca x Mo 2 O 9-δ (x ranges from 0 to 1.0) displaying colors ranging from green to yellow were synthesized by traditional solid-state route, as alternatives to lead, cadmium and chromium colorants. The yellow-green pigments were found to be interesting alternatives to existing toxic pigments for coloration of plastics. Display Omitted

Two-dimensional MoS2 electromechanical actuators

Science.gov (United States)

Hung, Nguyen T.; Nugraha, Ahmad R. T.; Saito, Riichiro

2018-02-01

We investigate the electromechanical properties of two-dimensional MoS2 monolayers with 1H, 1T, and 1T‧ structures as a function of charge doping by using density functional theory. We find isotropic elastic moduli in the 1H and 1T structures, while the 1T‧ structure exhibits an anisotropic elastic modulus. Moreover, the 1T structure is shown to have a negative Poisson’s ratio, while Poisson’s ratios of the 1H and 1T‧ are positive. By charge doping, the monolayer MoS2 shows a reversible strain and work density per cycle ranging from  -0.68% to 2.67% and from 4.4 to 36.9 MJ m-3, respectively, making them suitable for applications in electromechanical actuators. We also examine the stress generated in the MoS2 monolayers and we find that 1T and 1T‧ MoS2 monolayers have relatively better performance than 1H MoS2 monolayer. We argue that such excellent electromechanical performance originate from the electrical conductivity of the metallic 1T and semimetallic 1T‧ structures and also from their high Young’s modulus of about 150-200 GPa.

Luminescence properties of ZnMoO{sub 4}:Eu{sup 3+}:Y{sup 3+} materials synthesized by solution combustion synthesis method

Energy Technology Data Exchange (ETDEWEB)

Verma, Naveen, E-mail: vermanaveen17@gmail.com; Singh, Krishan Chander; Jindal, Jitender; Yadav, Suprabha [Department of chemistry, Maharshi Dayanand University, Rohtak-124001 – India (India); Mari, Bernabe; Mollar, Miguel [Institut de Disseny per la Fabricació Automatitzada - Departament de Física Aplicada, Universitat Politècnica de València, Camí de Vera s/n, 46022 València (Spain)

2016-04-13

The Zn{sub (1-x-y)}MoO{sub 4}:Eu{sup 3+}{sub (x)}: Y{sup 3+}{sub (y)} (x = 1 mol% and y = 1 or 2 mol%) compounds were prepared by combustion synthesis method. The crystal structure of the samples was identified by X-ray diffraction (XRD). The photoluminescence properties were investigated and it is observed that the co-doping of Y{sup 3+} enhances the luminescence emission intensity of ZnMoO{sub 4}:Eu{sup 3+} material. The Y{sup 3+} acts as a sensitizer in the ZnMoO{sub 4}:Eu{sup 3+} lattice. The particle size is calculated from XRD data by using Scherer Equation. The particles has been found in the range of 30-40 nm.

Magnetoresistance in Co/2D MoS2/Co and Ni/2D MoS2/Ni junctions.

Science.gov (United States)

Zhang, Han; Ye, Meng; Wang, Yangyang; Quhe, Ruge; Pan, Yuanyuan; Guo, Ying; Song, Zhigang; Yang, Jinbo; Guo, Wanlin; Lu, Jing

2016-06-28

Semiconducting single-layer (SL) and few-layer MoS2 have a flat surface, free of dangling bonds. Using density functional theory coupled with non-equilibrium Green's function method, we investigate the spin-polarized transport properties of Co/2D MoS2/Co and Ni/2D MoS2/Ni junctions with MoS2 layer numbers of N = 1, 3, and 5. Well-defined interfaces are formed between MoS2 and metal electrodes. The junctions with a SL MoS2 spacer are almost metallic owing to the strong coupling between MoS2 and the ferromagnets, while those are tunneling with a few layer MoS2 spacer. Both large magnetoresistance and tunneling magnetoresistance are found when fcc or hcp Co is used as an electrode. Therefore, flat single- and few-layer MoS2 can serve as an effective nonmagnetic spacer in a magnetoresistance or tunneling magnetoresistance device with a well-defined interface.

Phase formation in Na2MoO4 - MgMoO4 - Cr2(MoO4)3 system

International Nuclear Information System (INIS)

Kotova, I.Yu.; Kozhevnikova, N.M.

1998-01-01

Interaction within Na 2 MoO 4 - MgMoO 4 - Cr 2 (MoO 4 ) 3 ternary system is studied by X ray phase and DTA methods. State diagram of NaCr(MoO 4 ) 2 - MgMoO 4 section is plotted. Production of ternary molybdates of Na 1-x Mg 1-x Cr 1+x (MoO 4 ) 3 , where 0 ≤ x ≤ 0.3, and NaMg 3 Cr(MoO 4 ) 5 composition is ascertained [ru

Single-phase and warm white-light-emitting phosphors CaLa{sub 2−x−y}(MoO{sub 4}){sub 4}: xDy{sup 3+}, yEu{sup 3+}: Synthesis, luminescence and energy transfer

Energy Technology Data Exchange (ETDEWEB)

Han, Li; Liu, Guixia, E-mail: liuguixia22@163.com; Dong, Xiangting; Wang, Jinxian; Yu, Wensheng

2016-10-15

A series of single-phase warm white light emitting CaLa{sub 2−x−y}(MoO{sub 4}){sub 4}: xDy{sup 3+}, yEu{sup 3+} phosphors were synthesized by a typical sol–gel method. X-ray diffraction (XRD) analysis reveals that the crystal structures of the samples are matched well with the tetragonal CaMoO{sub 4}. Upon ultraviolet (UV) light radiation, the Dy{sup 3+} or Eu{sup 3+} ions singly activated CaLa{sub 2}(MoO{sub 4}){sub 4} phosphors exhibit corresponding emissions originated from the f–f transitions of Dy{sup 3+} or Eu{sup 3+} ions. Under near ultraviolet (n-UV) light excitation, in the Dy{sup 3+} and Eu{sup 3+} ions co-doped samples, the energy transfer (ET) phenomenon from Dy{sup 3+} to Eu{sup 3+} ions can be observed and has been demonstrated to be a quadrupole–quadrupole interaction mechanism. The emission color of CaLa{sub 1.98−y}(MoO{sub 4}){sub 4}: 0.02Dy{sup 3+}, yEu{sup 3+} samples can be tuned from cool to warm white light by adjusting the concentration of Eu{sup 3+} ions. In addition, it can be found that CaLa{sub 1.974}(MoO{sub 4}){sub 4}: 0.02Dy{sup 3+}, 0.006Eu{sup 3+} samples emit bright white light with the CIE coordinate of (0.348, 0.313) and the color temperature of 5087 K, which is very close to the standard white light. All the results demonstrate that the as-synthesized phosphors have great potential applications in the field of n-UV white light emitting diodes (WLEDs).

Effects of composition modulation on the luminescence properties of Eu(3+) doped Li1-xAgxLu(MoO4)2 solid-solution phosphors.

Science.gov (United States)

Cheng, Fangrui; Xia, Zhiguo; Molokeev, Maxim S; Jing, Xiping

2015-11-07

Double molybdate scheelite-type solid-solution phosphors Li1-xAgxLu1-y(MoO4)2:yEu(3+) were synthesized by the solid state reaction method, and their crystal structures and luminescence properties were investigated in detail. The composition modulation and structural evolution of this series of samples were studied and the selected AgEu(MoO4)2, AgLu(MoO4)2, LiLu(MoO4)2 and LiEu(MoO4)2 phases were analyzed based on the Rietveld refinement. Depending on the variation of the Li/Ag ratio in Li1-xAgxLu1-y(MoO4)2:yEu(3+) phosphors, the difference in the luminescence properties of Li1-xAgxLu1-y(MoO4)2:yEu(3+) phosphors was ascribed to two factors, one reason could be assigned to the coupling effect and the nonradiative transition between the energy levels of LixAg1-xLu(MoO4)2 matrices and the activator Eu(3+), another could be due to the near ultraviolet energy absorption and transmission efficiency between the charge-transfer (CT) band of O(2-)-Mo(6+) and the 4f → 4f emissive transitions of Eu(3+). The ultraviolet-visible diffuse reflection spectra (UV-vis DRS) and Raman spectra analysis were also used to verify the above mechanism.

Phase formation in the Li2MoO4-Rb2MoO4-Ln2(MoO4)3 systems and the properties of LiRbLn2(MoO4)4

International Nuclear Information System (INIS)

Basovich, O.M.; Khajkina, E.G.; Vasil'ev, E.V.; Frolov, A.M.

1995-01-01

Phase equilibria within subsolidus range of ternary salt systems Li 2 MoO 4 -Rb 2 MoO 4 -Ln 2 (MoO 4 ) 4 (Ln - Nd, Er) are analyzed. Formation of ternary molybdate LiRbNd 2 (MoO 4 ) 4 is proved along LiNd(MoO 4 ) 2 -RbNd(MoO 4 )-2 cross-section. Phase diagram of this cross-section is plotted. Similar compounds are synthesized for Ln = La-Eu. The parameters of their monoclinic elementary cells are determined. Luminescent properties of LiRbLa 2 (MoO 4 ) 4 -Nd 3+ are studied. 17 refs., 4 figs., 2 tabs

The transitions 4p-5s in Y VI, Zr VII, Nb VIII and Mo IX

International Nuclear Information System (INIS)

Chaghtai, M.S.Z.; Rahimullah, K.; Khatoon, S.

1976-01-01

With the help of the spectra recorded in the Physics Department of Lund University, Y VI, Zr VII, Nb VIII and Mo IX are freshly analysed. The five 4s 2 4p 4 ground levels and the ten 4s 2 4p 3 5s levels of previous analyses are confirmed in the first three spectra, except for revising in Y VI the 4p 4 1 S 0 and 4p 3 5s( 4 Ssub(3/2)) 2 levels and interchanging 5s( 2 Dsub(3/2)) 1 with 5s( 2 Dsub(3/2)) 2 . All level values are improved due to the new measurements. A new analysis of Mo IX establishing all the 4p 4 and 4p 3 5s levels is being reported. (Auth.)

Fatigue Resistance of GX12CrMoVNbN9-1 Cast Steel after Ageing Process

Directory of Open Access Journals (Sweden)

Stanisław MROZIŃSKI

2014-12-01

Full Text Available In the present paper, low cycle fatigue behaviour of GX12CrMoVNbN9-1 (GP91 cast steel is presented. Fatigue tests were performed under isothermal conditions at room temperature and at 550 and 600oC, on five levels of total strain amplitude value ɛac = 0.25÷0.60%. The cast steel subject to investigation was in the as-received condition (after heat treatment and after 8000 hours of ageing at the temperature of 600oC. Performed research has shown an insignificant influence of the ageing process on mechanical properties of GP91 cast steel, determined with the static test of tension. Analysis of the performed tests has proved that GP91 cast steel in the as-received condition and after ageing process was characterized by strong cyclic softening without a clear period of stabilization of the hysteresis loop parameters. The fatigue lifetime curves at each temperature were obtained based on Basquin and Coffin – Manson equations. The process of ageing of GP91 cast steel contributed to a decrease in its fatigue life Nf from a few to a few dozen percent, and the level of fatigue life was dependent on the value of strain amplitude ɛac. It has also been stated that the fatigue life Nf of GP91 cast steel is determined by its plastic properties, and the degree of changes in fatigue life Nf was dependent not only on the temperature of testing, but also on the value of strain amplitude ɛac. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6077

Enhanced field emission behavior of layered MoSe2

International Nuclear Information System (INIS)

Suryawanshi, Sachin R; Pawbake, Amit S; Jadkar, Sandesh R; More, Mahendra A; Pawar, Mahendra S; Late, Dattatray J

2016-01-01

Herein, we report one step facile chemical vapor deposition method for synthesis of single-layer MoSe 2 nanosheets with average lateral dimension ∼60 μm on 300 nm SiO 2 /Si and n-type silicon substrates and field emission investigation of MoSe 2 /Si at the base pressure of ∼1 × 10 −8 mbar. The morphological and structural analyses of the as-deposited single-layer MoSe 2 nanosheets were carried out using an optical microscopy, Raman spectroscopy and atomic force microscopy. Furthermore, the values of turn-on and threshold fields required to extract an emission current densities of 1 and 10 μA cm −2 , are found to be ∼1.9 and ∼2.3 V μm −1 , respectively. Interestingly, the MoSe 2 nanosheet emitter delivers maximum field emission current density of ∼1.5 mA cm −2 at a relatively lower applied electric field of ∼3.9 V μm −1 . The long term operational current stability recorded at the preset values of 35 μA over 3 hr duration and is found to be very good. The observed results demonstrates that the layered MoSe 2 nanosheet based field emitter can open up many opportunities for their potential application as an electron source in flat panel display, transmission electron microscope, and x-ray generation. Thus, the facile one step synthesis approach and robust nature of single-layer MoSe 2 nanosheets emitter can provide prospects for the future development of practical electron sources. (paper)

Comparison of midupper arm circumference and weight-for-height z score for assessing acute malnutrition in Bangladeshi children aged 6-60 mo: an analytical study.

Science.gov (United States)

Hossain, Md Iqbal; Ahmed, Tahmeed; Arifeen, Shams El; Billah, Sk Masum; Faruque, Asg; Islam, M Munirul; Jackson, Alan A

2017-11-01

Background : In clinical settings, wasting in childhood has primarily been assessed with the use of a weight-for-height z score (WHZ), and in community settings, it has been assessed via the midupper arm circumference (MUAC) with a cutoff children were not identified when these cutoffs for MUAC were used. Objective: We determined the cutoffs for MUAC to detect wasting in Bangladeshi children aged 6-60 mo. Design: A secondary analysis was carried out on data from 27,767 children aged 6-59 mo. This analysis comprised 1 ) 9131 children across Bangladesh and 2 ) 18,636 children enrolled in a surveillance study in the Dhaka Hospital of icddr,b during 1996-2014. The area under the receiver operating curve was used to indicate the most appropriate choice for cutoffs that related MUAC with WHZ. Results: The mean ± SD age for the entire group was 21 ± 14 mo, WHZ was -1.18 ± 1.23, height-for-age z score was -1.63 ± 1.39, MUAC was 136 ± 14 mm, and 45% of subjects were girls. MUAC correlated with the WHZ ( r : 0.618, P < 0.001). Age-stratified analyses revealed that, for ages 6-24 mo, MUAC cutoffs were <120 mm for a WHZ <-3 and <125 mm for a WHZ <-2 with a sensitivity of 72.9% and 63.2%, respectively, and a specificity of 84.7% and 85.3%, respectively; for ages 25-36 mo, MUAC cutoffs were <125 mm for a WHZ <-3 and <135 mm for a WHZ <-2 with a sensitivity of 55.0% and 71.7%, respectively, and a specificity of 92.8% and 78.7% respectively; and for ages 37-60 mo, MUAC cutoffs were <135 mm for a WHZ <-3 and <140 mm for a WHZ <-2 with a sensitivity of 71.4% and 70.4%, respectively, and a specificity of 84.6% and 80.3%, respectively. Conclusion: The respective cutoffs for MUAC to better capture the vulnerability and risk of severe (WHZ <-3) and moderate (WHZ <-2) wasting would be <120 and <125 mm for ages 6-24 mo, <125 and <135 mm for ages 25-36 mo, and <135 and <140 mm for ages 37-60 mo. © 2017 American Society for Nutrition.

Gold nanoparticles on MoS2 layered crystal flakes

International Nuclear Information System (INIS)

Cao, Wei; Pankratov, Vladimir; Huttula, Marko; Shi, Xinying; Saukko, Sami; Huang, Zhongjia; Zhang, Meng

2015-01-01

Inorganic layered crystal MoS 2 is considered as one of the most promising and efficient semiconductor materials for future transistors, photoelectronics, and electrocatalysis. To boost MoS 2 -based material applications, one direction is to grow physically and chemically reactive nanoparticles onto MoS 2 . Here we report on a simple route to synthesis crystalized MoS 2 –Au complexes. The gold nanoparticles were grown on MoS 2 flakes through a wet method in the oxygen free environment at room temperature. Nanoparticles with diameters varying from 9 nm to 429 nm were controlled by the molar ratios of MoS 2 and HAuCl 4 precursors. MoS 2 host flakes keep intrinsic honeycomb layered structures and the Au nanoparticles cubic-center crystal microstructures. From product chemical states analysis, the synthesis was found driven by redox reactions between the sulphide and the chloroauric acid. Photoluminescence measurement showed that introducing Au nanoparticles onto MoS 2 stacks substantially prompted excitonic transitions of stacks, as an analogy for doping Si wafers with dopants. Such composites may have potential applications in wide ranges similar as the doped Si. - Highlights: • The Au nanoparticles were decorated on MoS 2 in oxygen free ambiences via a wet method. • The Au nanoparticles are size-controllable and crystalized. • Chemical reaction scheme was clarified. • The MoS 2 –Au complexes have strong photoluminescent properties

Symmetrical synergy of hybrid Co9S8-MoSx electrocatalysts for hydrogen evolution reaction

KAUST Repository

Zhou, Xiaofeng; Yang, Xiulin; Hedhili, Mohamed N.; Li, Henan; Min, Shixiong; Ming, Jun; Huang, Kuo-Wei; Zhang, Wenjing; Li, Lain-Jong

2017-01-01

There exists a strong demand to replace expensive noble metal catalysts with efficient and earth-abundant catalysts for hydrogen evolution reaction (HER). Recently the Co- and Mo-based sulfides such as CoS2, Co9S8, and MoSx have been considered

Preparation and electrical properties of MoO{sub 3}-modified SrBi{sub 2}Nb{sub 2}O{sub 9}-based lead-free piezoelectric ceramics

Energy Technology Data Exchange (ETDEWEB)

Yao, Zhongran, E-mail: ruiqingchu@sohu.com [College of Materials Science and Engineering, Liaocheng University, Liaocheng 252059 (China); Chu, Ruiqing, E-mail: rqchu@lcu.edu.cn [College of Materials Science and Engineering, Liaocheng University, Liaocheng 252059 (China); Xu, Zhijun; Hao, Jigong; Wei, Denghu; Cheng, Renfei [College of Materials Science and Engineering, Liaocheng University, Liaocheng 252059 (China); Li, Guorong [The State Key Lab of High Performance Ceramics and Superfinemicrostructure, Shanghai Institute of Ceramics, Chinese Academy of Science, Shanghai 200050 (China)

2016-05-05

Lead-free piezoelectric ceramics, SrBi{sub 2}(Nb{sub 1-x}Mo{sub x}){sub 2}O{sub 9} (SBNM-x), were prepared by a conventional solid-state reaction method. The crystal structure, microstructure and electrical properties were systematically investigated. The X-ray diffraction analysis suggested that the substitution formed layered perovskite structure. Plate-like morphology of the grains which is characteristic for layer-structure Aurivillius compounds was clearly observed for all the samples. The excellent electrical properties (e.g., d{sub 33}∼18 pC/N, 2P{sub r}∼20.34 μC/cm{sup 2}) and a high Curie temperature (e.g., T{sub c}∼458 °C) are simultaneously obtained in the ceramics with x = 0.12. Additionally, thermal annealing studies indicated that piezoelectric constant (d{sub 33}) of SBNM-0.12 ceramic remains almost unchanged (16 pC/N, only decrease by 12%) at temperatures below 400 °C, demonstrating that the Mo-modified SBN-based ceramics are the promising candidates for high-temperature applications. - Highlights: • Higher valent cation Mo{sup 6+} substituted for B-site Nb{sup 5+} in the perovskite layers ions. • The piezoelectric constant (d{sub 33}) of SrBi{sub 2}Nb{sub 2}O{sub 9} ceramic is increased to be 18 pC/N. • The remnant polarization (2P{sub r}) of SrBi{sub 2}Nb{sub 2}O{sub 9} ceramic is increased to be 20.34 μC cm{sup −2}. • SBNM-x ceramics show good temperature stability for high temperature applications.

Effect of ageing on the microstructural stability of cold-worked titanium-modified 15Cr-15Ni-2.5Mo austenitic stainless steel

International Nuclear Information System (INIS)

Venkadesan, S.; Bhaduri, A.K.; Rodriguez, P.; Padmanabhan, K.A.

1992-01-01

A titanium-modified 15Cr-15Ni-2.5Mo austenitic stainless steel conforming to ASTM A 771 (UNS S 38660), commercially called Alloy D9, is being indigenously developed for application as material for the fuel clad and the hexagonal wrapper for fuel subassemblies of the Prototype Fast Breeder Reactor. As this material would be used in the cold-worked condition and would be subjected to prolonged exposure to elevated service temperatures, the effect of ageing on the microstructural stability was studied as a function of the amount of cold work. The material was given 2.5-30% prior cold work and then aged at temperatures in the range 923 to 1173 K for times ranging from 0.25 to 1000 h. Hardness measurements made before and after ageing were correlated with the Larson-Miller parameter to determine the highest stable prior cold-work level. Optical microscopy was used to study the microstructural changes. The influence of prolonged exposure for two and three years at the operating temperatures of clad and wrapper, on the elevated temperature tensile properties of a 20% prior cold-worked Alloy D9 was also studied through accelerated ageing treatments based on the present parametric approach. (orig.)

Investigation of chemical bond characteristics, thermal expansion coefficients and bulk moduli of alpha-R2MoO6 and R2Mo2O7 (R = rare earths) by using a dielectric chemical bond method.

Science.gov (United States)

Li, Huaiyong; Zhang, Siyuan; Zhou, Shihong; Cao, Xueqiang

2009-09-01

Theoretical researches are performed on the alpha-R2MoO6 (R = Y, Gd, Tb Dy, Ho, Er, Tm and Yb) and pyrochlore-type R2Mo2O7 (R = Y, Nd, Sm, Gd, Tb and Dy) rare earth molybdates by using chemical bond theory of dielectric description. The chemical bonding characteristics and their relationship with thermal expansion property and compressibility are explored. The calculated values of linear thermal expansion coefficient (LTEC) and bulk modulus agree well with the available experimental values. The calculations reveal that the LTECs and the bulk moduli do have linear relationship with the ionic radii of the lanthanides: the LTEC decreases from 6.80 to 6.62 10(-6)/K and the bulk modulus increases from 141 to 154 GPa when R goes in the order Gd, Tb Dy, Ho, Er, Tm, and Yb in the alpha-R2MoO6 series; while in the R2Mo2O7 series, the LTEC ranges from 6.80 to 6.61 10(-6)/K and the bulk modulus ranges from 147 to 163 GPa when R varies in the order Nd, Sm, Gd, Tb and Dy. Copyright 2008 Wiley Periodicals, Inc.

Luminescence and luminescence quenching of highly efficient Y2Mo4O15:Eu3+ phosphors and ceramics

OpenAIRE

Janulevičius, Matas; Marmokas, Paulius; Misevičius, Martynas; Grigorjevaitė, Julija; Mikoliūnaitė, Lina; Šakirzanovas, Simas; Katelnikovas, Artūras

2016-01-01

A good LED phosphor must possess strong enough absorption, high quantum yields, colour purity, and quenching temperatures. Our synthesized Y2Mo4O15:Eu3+ phosphors possess all of these properties. Excitation of these materials with near-UV or blue radiation yields bright red emission and the colour coordinates are relatively stable upon temperature increase. Furthermore, samples doped with 50% Eu3+ showed quantum yields up to 85%, what is suitable for commercial application. Temperature depend...

Diagnostic criteria for severe acute malnutrition among infants aged under 6 mo.

Science.gov (United States)

Mwangome, Martha; Ngari, Moses; Fegan, Greg; Mturi, Neema; Shebe, Mohammed; Bauni, Evasius; Berkley, James A

2017-06-01

Background: There is an increasing recognition of malnutrition among infants under 6 mo of age (U6M). Current diagnosis criteria use weight-for-length z scores (WLZs), but the 2006 WHO standards exclude infants shorter than 45 cm. In older children, midupper arm circumference (MUAC) predicts mortality better than does WLZ. Outcomes may also be influenced by exposure to HIV and size or gestational age at birth. Diagnostic thresholds for WLZ, MUAC, and other indexes have not been fully evaluated against mortality risk among U6M infants. Objective: The aim was to determine the association of anthropometric indexes with risks of inpatient and postdischarge mortality among U6M infants recruited at the time of hospitalization. Design: We analyzed data from a cohort of U6M infants admitted to Kilifi County Hospital (2007-2013), Kenya. The primary outcomes were inpatient death and death during follow-up over 1 y after discharge. We calculated adjusted RRs for inpatient mortality and HRs for postdischarge mortality for different anthropometric measures and thresholds. Discriminatory value was assessed by using receiver operating characteristic curves. Results: A total of 2882 infants were admitted: 140 (4.9%) died in the hospital and 1405 infants were followed up after discharge. Of these, 75 (5.3%) died within 1 y during 1318 child-years of observation. MUAC and weight-for-age z score (WAZ) predicted inpatient and postdischarge mortality better than did WLZ ( P 0.05) and performed better than WLZ <-3 for both inpatient and postdischarge mortality (both P < 0.001). Reported small size at birth did not reduce the risk of death associated with anthropometric indexes. Conclusions: U6M infants at the highest risk of death are best targeted by using MUAC or WAZ. Further research into the effectiveness of potential interventions is required.

Correlation of microstructure and fracture toughness of advanced 9Cr/CrMoV dissimilarly welded joint

Energy Technology Data Exchange (ETDEWEB)

Guo, Qian [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Lu, Fenggui, E-mail: Lfg119@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Liu, Xia [Shanghai Turbine Plant of Shanghai Electric Power Generation Equipment Co. Ltd., Shanghai 200240 (China); Yang, Renjie [Shanghai Turbine Works Company, Shanghai 200240 (China); Cui, Haichao [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yulai, E-mail: ylgao@shu.edu.cn [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai 200072 (China)

2015-06-25

In this paper, the fracture toughness and the related microstructure characteristics of dissimilarly welded joint manufactured by advanced 9Cr and CrMoV steels were systematically investigated. The dissimilarly welded joint was fabricated by narrow gap submerged arc welding (NG-SAW) applying multi-layer and multi-pass technique. Fracture toughness, as one of the most important property to assess the reliability of welded joint, was studied for different regions including CrMoV base metal (CrMoV-BM), heat affected zone (HAZ) of CrMoV side (CrMoV-HAZ), weld metal (WM), heat affected zone of 9Cr side (9Cr-HAZ) and 9Cr base metal (9Cr-BM). It was found that the fracture toughness of CrMoV-BM, CrMoV-HAZ and WM was better than that of 9Cr-HAZ and 9Cr-BM. In order to illustrate these results, the microstructure of the whole welded joint was observed by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM) detailedly. It was found that the fine high-temperature tempered martensite and bainite in WM, CrMoV-BM and CrMoV-HAZ contribute to the higher fracture toughness, while lower fracture toughness for 9Cr-BM and HAZ was caused by coarse tempered lath-martensite. Furthermore, the fracture morphology showed that ductile fracture occurred in WM and CrMoV side, while brittle fracture appeared in BM and HAZ of 9Cr side.

Recent progress on RE2O3-Mo/W emission materials.

Science.gov (United States)

Wang, Jinshu; Zhang, Xizhu; Liu, Wei; Cui, Yuntao; Wang, Yiman; Zhou, Meiling

2012-08-01

RE2O3-Mo/W cathodes were prepared by powder metallurgy method. La2O3-Y2O3-Mo cermet cathodes prepared by traditional sintering method and spark plasma sintering (SPS) exhibit different secondary emission properties. The La2O3-Y2O3-Mo cermet cathode prepared by SPS method has smaller grain size and exhibits better secondary emission performance. Monte carlo calculation results indicate that the secondary electron emission way of the cathode correlates with the grain size. Decreasing the grain size can decrease the positive charging effect of RE2O3 and thus is favorable for the escaping of secondary electrons to vacuum. The Scandia doped tungsten matrix dispenser cathode with a sub-micrometer microstructure of matrix with uniformly distributed nanometer-particles of Scandia has good thermionic emission property. Over 100 A/cm2 full space charge limited current density can be obtained at 950Cb. The cathode surface is covered by a Ba-Sc-O active surface layer with nano-particles distributing mainly on growth steps of W grains, leads to the conspicuous emission property of the cathode.

Effects of boron addition on the formation of MoSi2 by combustion synthesis mode

International Nuclear Information System (INIS)

Feng Peizhong; Wu Jie; Islam, S.H.; Liu Weisheng; Niu Jinan; Wang Xiaohong; Qiang Yinghuai

2010-01-01

The combustion synthesis behavior of Mo-Si-B powder was investigated. Test specimens with nominal compositions including MoSi 2 , Mo(Si 0.975 B 0.025 ) 2 , Mo(Si 0.95 B 0.05 ) 2 , Mo(Si 0.925 B 0.075 ) 2 and Mo(Si 0.9 B 0.1 ) 2 were employed. The combustion mode, propagation velocity of combustion wave, combustion temperature and combustion product structure were studied. The results showed that the combustion wave propagated along a spiral trajectory till reaching the bottom of the compacts. The combustion temperature was increased by the addition of boron, to as high as 1922 K in the case of the Mo(Si 0.95 B 0.05 ) 2 sample. However, the flame-front propagation velocity decreased as a result of the addition of boron. The X-ray diffraction results showed that the combustion products of the Mo(Si 0.975 B 0.025 ) 2 and Mo(Si 0.9 B 0.1 ) 2 samples were composed of MoSi 2 with minor MoB. Those of the Mo(Si 0.95 B 0.05 ) 2 and Mo(Si 0.925 B 0.075 ) 2 samples were composed of MoSi 2 with minor MoB and MoB 2 . And traces of Mo 2 B 5 were identified in the Mo(Si 0.95 B 0.05 ) 2 sample.

Cationic Intermixing and Reactivity at the La2 Mo2 O9 /La0.8 Sr0.2 MnO3-δ Solid Oxide Fuel Cell Electrolyte-Cathode Interface.

Science.gov (United States)

Ravella, Uday K; Liu, Jingjing; Corbel, Gwenaël; Skinner, Stephen J; Lacorre, Philippe

2016-08-23

Among standard high-temperature cathode materials for solid oxide fuel cells, La0.8 Sr0.2 MnO3-δ (LSM) displays the least reactivity with the oxide-ion conductor La2 Mo2 O9 (LMO), yet a reaction is observed at high processing temperatures, identified by using XRD and focused ion beam secondary-ion mass spectrometry (FIB-SIMS) after annealing at 1050 and 1150 °C. Additionally, Sr and Mn solutions were deposited and annealed on LMO pellets, as well as a Mo solution on a LSM pellet. From these studies several reaction products were identified by using XRD and located by using FIB-SIMS on the surface of pelletised samples. We used depth profiling to show that the reactivity extended up to ∼10 μm from the surface region. If Sr was present, a SrMoO4 -type scheelite phase was always observed as a reaction product, and if Mn was present, LaMnO3+δ single crystals were observed on the surface of the LMO pellets. Additional phases such as La2 MoO6 and La6 MoO12 were also detected depending on the configuration and annealing temperature. Reaction mechanisms and detailed reaction formulae are proposed to explain these observations. The strongest driving force for cationic diffusion appears to originate from Mo(6+) and Mn(3+) cations, rather than from Sr(2+) . © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Serotonin and Dopamine Transporter Binding in Children with Autism Determined by SPECT

Science.gov (United States)

Makkonen, Ismo; Riikonen, Raili; Kokki, Hannu; Airaksinen, Mauno M.; Kuikka, Jyrki T.

2008-01-01

Disturbances in the serotonergic system have been recognized in autism. To investigate the association between serotonin and dopamine transporters and autism, we studied 15 children (14 males, one female; mean age 8y 8mo [SD 3y 10mo]) with autism and 10 non-autistic comparison children (five males, five females; mean age 9y 10mo [SD 2y 8mo]) using…

Applicability of the θ projection method to creep curves of Ni-22Cr-18Fe-9Mo alloy

International Nuclear Information System (INIS)

Kurata, Yuji; Utsumi, Hirokazu

1998-01-01

Applicability of the θ projection method has been examined for constant-load creep test results at 800 and 1000degC on Ni-22Cr-18Fe-9Mo alloy in the solution-treated and aged conditions. The results obtained are as follows: (1) Normal type creep curves obtained at 1000degC for aged Ni-22Cr-18Fe-9Mo alloy are fitted using the θ projection method with four θ parameters. Stress dependence of θ parameters can be expressed in terms of simple equations. (2) The θ projection method with four θ parameters cannot be applied to the remaining creep curves where most of the life is occupied by a tertiary creep stage. Therefore, the θ projection method consisting of only the tertiary creep component with two θ parameters was applied. The creep curves can be fitted using this method. (3) If the θ projection method with four θ or two θ parameters is applied to creep curves in accordance with creep curve shapes, creep rupture time can be predicted in terms of formulation of stress and/or temperature dependence of θ parameters. (author)

Comparative study on catalytic behavior of polynuclear Mg-Mo-complex and FeMo-co-factor of nitrogenase in reactions with C2H2, N2 and CO

International Nuclear Information System (INIS)

Bardina, N.V.; Bazhenova, T.A.; Petrova, G.N.; Shilova, A.K.; Shilov, A.E.

2006-01-01

Catalytic reduction kinetics of C 2 H 2 in the presence of the Mg-Mo-cluster {[Mg 2 Mo 8 O 22 (MeO) 6 (MeOH) 4 ] 2- [Mg(MeOH) 6 ] 2+ }·6MeOH 1 is studied. Several interdependent coordinating centers are active in reference to substrates and inhibitors in the polynuclear Mg-Mo-complex, as in the reduced by europium amalgam (μ 6 -N)MoFe 7 S 9 ·homocitrate (FeMoco, 2). Comparison of regularities in reduction mechanism of C 2 H 2 , N 2 and CO with the participation of synthetic polynuclear complex 1 and natural cluster 2 is conducted. Regularities of the studied reactions in the systems involving natural catalytic cluster FeMoco and the synthetic Mg-Mo-complex modelling of its effect are noted to be similar. The main variations the systems show as regards to the reaction with molecular nitrogen [ru

Structure of glasses of the TeO2-MoO3 system

International Nuclear Information System (INIS)

Dimitriev, Y.; Dimitrov, V.; Bart, J.C.J.

1981-01-01

Structural models for glasses of the TeO 2 -MoO 3 system are suggested. On the basis of X-ray and infrared spectral investigations, by comparing with known crystalline structures of TeO 2 , MoO 3 and Te 2 MoO 7 9t 2 M, it is shown that the glasses from TeO 2 to Te 2 MoO 7 possess [TeO 4 ] and [MoO 5 ] groups as basic structural units. The latter are connected to form [Mo 2 O 8 ] complexes. The glasses in the MoO 3 -rich compositional range are built up of [TeO 3 ] and [MoO 6 ] polyhedra. The glass-formation tendency is discussed in relation to the role of the free electron pair and the disruption of secondary and weak primary bonds in the crystals. (author)

Análisis mecánico y tribológico de los recubrimientos fe-cr-ni-c y ni-al-mo

Directory of Open Access Journals (Sweden)

JORGE E. MUÑOZ

2007-01-01

Full Text Available En este trabajo de investigación se evaluaron dos recubrimientos aplicados por medio de la técnica de rociado térmico por combustión, la aleación: Ni=89%, Al = 5,5%, Mo=5,5% y la aleación Fe=81,8%, Cr=16%, Ni=2%, C=0,2. La preparación superficial de las probetas se realizó usando chorro de arena. Se realizaron pruebas de resistencia al cortante, adherencia, desgaste abrasivo, desgaste por deslizamiento y flexión en cuatro puntos. El recubrimiento Fe-Cr-Ni-C presentó menor pérdida de masa, tanto para desgaste abrasivo como para el desgaste por deslizamiento. La multicapa presentó una mayor porosidad en el recubrimiento Ni-Al- Mo usado como capa base y la capa exterior de Fe-Cr-Ni-C presentó mayor cantidad de partículas no fundidas y óxidos. La falla ocurrida en el ensayo de adherencia para las probetas con recubrimiento multicapa fue de característica adhesiva y cohesiva. El esfuerzo en el que se presenta la fisura por flexión en el recubrimiento multicapa disminuyó con el aumento del espesor

Resistencia a la corrosión a alta temperatura de recubrimientos NiCrAlY y NiCrFeNbMoTiAl depositados por APS

Directory of Open Access Journals (Sweden)

José Luis Tristancho-Reyes

2014-12-01

Full Text Available La corrosión a alta temperatura de las tuberías utilizadas en equipos generadores de vapor (calderas ha sido reconocida como un grave problema que trae consigo el adelgazamiento de éstas y, por consiguiente, la falla de los equipos. En la última década se han incrementado las investigaciones que involucran recubrimientos protectores que ayudan de alguna manera a prolongar la vida útil de estos equipos. Esta investigación determinó el comportamiento de los recubrimientos NiCrAlY y NiCrFeNbMoTiAl depositados por proyección térmica asistida por plasma (APS sobre la aleación SA213 – T22 (2¼Cr – 1Mo, en un ambiente corrosivo de 80%V2O5–20%K2SO4 a 800°C. Los valores de la cinética de corrosión fueron determinados mediante resistencia a la polarización lineal (RPL y espectroscopia de impedancia electroquímica (EIE. Los resultados obtenidos muestran una menor cinética de corrosión en el recubrimiento NiCrFeNbMoTiAl que la presentada por el recubrimiento NiCrAlY, corroborado por Microscopia Electrónica de Barrido (MEB.

Preparation of Zr(Mo,W)2O8 with a larger negative thermal expansion by controlling the thermal decomposition of Zr(Mo,W)2(OH,Cl)2∙2H2O.

Science.gov (United States)

Petrushina, Mariya Yu; Dedova, Elena S; Filatov, Eugeny Yu; Plyusnin, Pavel E; Korenev, Sergei V; Kulkov, Sergei N; Derevyannikova, Elizaveta A; Sharafutdinov, Marat R; Gubanov, Alexander I

2018-03-28

Solid solutions of Zr(Mo,W) 2 O 7 (OH,Cl) 2 ∙2H 2 O with a preset ratio of components were prepared by a hydrothermal method. The chemical composition of the solutions was determined by energy dispersive X-ray spectroscopy (EDX). For all the samples of ZrMo x W 2-x O 7 (OH,Cl) 2 ∙2H 2 O (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0), TGA and in situ powder X-ray diffraction (PXRD) studies (300-1100 K) were conducted. For each case, the boundaries of the transformations were determined: Zr(Mo,W) 2 O 7 (OH,Cl) 2 ∙2H 2 O → orthorhombic-ZrMo x W 2-x O 8 (425-525 K), orthorhombic-ZrMo x W 2-x O 8  → cubic-ZrMo x W 2-x O 8 (700-850 K), cubic-ZrMo x W 2-x O 8  → trigonal-ZrMo x W 2-x O 8 (800-1050 K for x > 1) and cubic-ZrMo x W 2-x O 8  → oxides (1000-1075 K for x ≤ 1). The cell parameters of the disordered cubic-ZrMo x W 2-x O 8 (space group Pa-3) were measured within 300-900 K, and the thermal expansion coefficients were calculated: -3.5∙10 -6  - -4.5∙10 -6  K -1 . For the ordered ZrMo 1.8 W 0.2 O 8 (space group P2 1 3), a negative thermal expansion (NTE) coefficient -9.6∙10 -6  K -1 (300-400 K) was calculated. Orthorhombic-ZrW2O 8 is formed upon the decomposition of ZrW 2 O 7 (OH,Cl) 2 ∙2H 2 O within 500-800 K.

Ternary system of Na2MoO4-Cs2MoO4-MoO3

International Nuclear Information System (INIS)

Zueva, V.P.; Shabanova, A.N.; Drobasheva, T.I.

1982-01-01

Using the methods of thermal analysis interaction of components in ternary system Na 2 MoO 4 -Cs 2 MoO 4 -MoO 3 has been studied. Crystallization surface consists of nine fields belonging to initial components and compounds of lateral sides. Triangulation of the system is carried out and the character of nonvariant points is clarified, the temperature of 360 deg C corresponds to low-melting eutectics

Effects of HFIR irradiation at 550C on the microstructure and toughness of HT-9 and 9Cr-1Mo

International Nuclear Information System (INIS)

Gelles, D.S.; Hu, W.L.; Huang, F.H.; Johnson, G.D.

1984-01-01

Results are reported for base metal and weld metal specimens of HT-9 and Modified 9Cr-1Mo following irradiation in HFIR at 55 0 C to 5 dpa. The DBTT shifts in irradiated base metal specimens were 30 0 C for HT-9 and 90 0 C for 9Cr-1Mo with further shifts of 20 0 C for weld metal. Concurrently, strength as measured by hardness increased 15 percent for HT-9 and 25 percent for 9Cr-1Mo. The hardness increases can be attributed in part to defect clusters 1.5 to 3.0 nm in diameter at densities approaching 10 17 cm -3 and also to lower rates of cavity nucleation ahead of the propagating crack

Effect of vitamin A supplementation with BCG vaccine at birth on vitamin A status at 6 wk and 4 mo of age

DEFF Research Database (Denmark)

Fisker, Ane B; Lisse, Ida M; Aaby, Peter

2007-01-01

with higher (9%; 95% CI: 2, 17%) RBP concentrations in children of noneducated mothers but not in children of educated mothers. Overall, RBP concentrations increased between 6 wk and 4 mo of age. The increase correlated inversely with the number of diphtheria-tetanus-pertussis (DTP) vaccines received...

HIDRODENITROGENACION DE CARBAZOL SOBRE CATALIZADORES NiMo/Al2O3-SiO2(x

Directory of Open Access Journals (Sweden)

Felipe Sánchez-Minero

2012-01-01

Full Text Available En este trabajo se estudió la velocidad de reacción del carbazol sobre catalizadores NiMo soportados sobre Al2O3 modificada superficialmente con SiO2 (0 y 10 % en peso de SiO2 en el soporte. Los catalizadores fueron evaluados en un reactor intermitente a cuatro temperaturas (287, 300, 312 y 325oC, presión de 4.0 MPa y relación molar hidrogeno/carbazol de 2400. A partir de los resultados experimentales se realizó un estudio cinético utilizando ecuaciones del tipo Langmuir-Hinshelwood (L-H. Luego, los parámetros cinéticos fueron estimados mediante la minimización de Powell (programa Scientist de MicroMath. Los resultados muestran que el catalizador con sílice (NiMo-SAC 10 alcanza una mayor actividad para la HDN de carbazol debido a que presenta un mayor número de sitios activos (valor de A, así como una menor fuerza de adsorción entre el reactante y la superficie catalítica (valor de KN, lo cual posiblemente favorece una mejor regeneración de sitios activos.

Order and disorder in the local and long-range structure of the spin-glass pyrochlore, Tb{sub 2}Mo{sub 2}O{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Jiang, Yu; Huq, Ashfia; Booth, Corwin H.; Ehlers, Georg; Greedan, John E.; Gardner, Jason S.

2011-02-11

To understand the origin of the spin-glass state in molybdate pyrochlores, the structure of Tb{sub 2}Mo{sub 2}O{sub 7} is investigated using two techniques: the long-range lattice structure was measured using neutron powder diffraction (NPD), and local structure information was obtained from the extended x-ray absorption fine structure (EXAFS) technique. While the long-range structure appears generally well ordered, enhanced mean-squared site displacements on the O(1) site and the lack of temperature dependence of the strongly anisotropic displacement parameters for both the Mo and O(1) sites indicate some disorder exists. Likewise, the local structure measurements indicate some Mo-Mo and Tb-O(1) nearest-neighbor disorder exists, similar to that found in the related spin-glass pyrochlore, Y{sub 2}Mo{sub 2}O{sub 7}. Although the freezing temperature in Tb{sub 2}Mo{sub 2}O{sub 7}, 25 K, is slightly higher than in Y{sub 2}Mo{sub 2}O{sub 7}, 22 K, the degree of local pair distance disorder is actually less in Tb{sub 2}Mo{sub 2}O{sub 7}. This apparent contradiction is considered in light of the interactions involved in the freezing process.

Composite Fe - BaCe0.2Zr0.6Y0.2O2.9 Anodes for Proton Conductor Fuel Cells

DEFF Research Database (Denmark)

Lapina, Alberto; Chatzichristodoulou, Christodoulos; Holtappels, Peter

2014-01-01

Symmetrical cells with Fe - BaCe0.2Zr0.6Y0.2O2.9 composite electrodes are produced by screen printing and infiltration, using BaCe0.2Zr0.6Y0.2O2.9 as electrolyte. The electrochemical performance of the composite electrode is studied by impedance spectroscopy at 250–500◦C in dry and wet hydrogen/n...

Thermal expansion studies on Th(MoO4)2, Na2Th(MoO4)3 and Na4Th(MoO4)4

International Nuclear Information System (INIS)

Keskar, Meera; Krishnan, K.; Dahale, N.D.

2008-01-01

Thermal expansion behavior of Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 was studied under vacuum in the temperature range of 298-1123 K by high temperature X-ray diffractometer. Th(MoO 4 ) 2 was synthesized by reacting ThO 2 with 2 mol of MoO 3 , at 1073 K in air and Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were prepared by reacting Th(MoO 4 ) 2 with 1 and 2 mol of Na 2 MoO 4 , respectively at 873 K in air. The XRD data of Th(MoO 4 ) 2 was indexed on orthorhombic system where as XRD data of Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were indexed on tetragonal system. The lattice parameters and cell volume of all the three compounds, fit into polynomial expression with respect to temperature, showed positive thermal expansion (PTE) up to 1123 K. The average value of thermal expansion coefficients for Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were determined from the high temperature data

Structural and thermodynamic study of dicesium molybdate Cs2Mo2O7: Implications for fast neutron reactors

Science.gov (United States)

Smith, A. L.; Kauric, G.; van Eijck, L.; Goubitz, K.; Wallez, G.; Griveau, J.-C.; Colineau, E.; Clavier, N.; Konings, R. J. M.

2017-09-01

The structure of α-Cs2Mo2O7 (monoclinic in space group P21 / c), which can form during irradiation in fast breeder reactors in the space between nuclear fuel and cladding, has been refined in this work at room temperature from neutron diffraction data. Furthermore, the compounds' thermal expansion and polymorphism have been investigated using high temperature X-ray diffraction combined with high temperature Raman spectroscopy. A phase transition has been observed at Ttr(α → β)=(621.9±0.8) K using Differential Scanning Calorimetry, and the structure of the β-Cs2Mo2O7 phase, orthorhombic in space group Pbcm, has been solved ab initio from the high temperature X-ray diffraction data. Furthermore, the low temperature heat capacity of α-Cs2Mo2O7 has been measured in the temperature range T=(1.9-313.2) K using a Quantum Design PPMS (Physical Property Measurement System) calorimeter. The heat capacity and entropy values at T=298.15 K have been derived as Cp,mo (Cs2Mo2O7 , cr , 298.15 K) = (211.9 ± 2.1) J K-1mol-1 and Smo (Cs2Mo2O7 , cr , 298.15 K) = (317.4 ± 4.3) J K-1mol-1 . When combined with the enthalpy of formation reported in the literature, these data yield standard entropy and Gibbs energy of formation as Δf Smo (Cs2Mo2O7 , cr , 298.15 K) = - (628.2 ± 4.4) J K-1mol-1 and Δf Gmo (Cs2Mo2O7 , cr , 298.15 K) = - (2115.1 ± 2.5) kJmol-1 . Finally, the cesium partial pressure expected in the gap between fuel and cladding following the disproportionation reaction 2Cs2MoO4=Cs2Mo2O7+2Cs(g)+ 1/2 O2(g) has been calculated from the newly determined thermodynamic functions.

The modulation of Schottky barriers of metal-MoS2 contacts via BN-MoS2 heterostructures.

Science.gov (United States)

Su, Jie; Feng, Liping; Zhang, Yan; Liu, Zhengtang

2016-06-22

Using first-principles calculations within density functional theory, we systematically studied the effect of BN-MoS2 heterostructure on the Schottky barriers of metal-MoS2 contacts. Two types of FETs are designed according to the area of the BN-MoS2 heterostructure. Results show that the vertical and lateral Schottky barriers in all the studied contacts, irrespective of the work function of the metal, are significantly reduced or even vanish when the BN-MoS2 heterostructure substitutes the monolayer MoS2. Only the n-type lateral Schottky barrier of Au/BN-MoS2 contact relates to the area of the BN-MoS2 heterostructure. Notably, the Pt-MoS2 contact with n-type character is transformed into a p-type contact upon substituting the monolayer MoS2 by a BN-MoS2 heterostructure. These changes of the contact natures are ascribed to the variation of Fermi level pinning, work function and charge distribution. Analysis demonstrates that the Fermi level pinning effects are significantly weakened for metal/BN-MoS2 contacts because no gap states dominated by MoS2 are formed, in contrast to those of metal-MoS2 contacts. Although additional BN layers reduce the interlayer interaction and the work function of the metal, the Schottky barriers of metal/BN-MoS2 contacts still do not obey the Schottky-Mott rule. Moreover, different from metal-MoS2 contacts, the charges transfer from electrodes to the monolayer MoS2, resulting in an increment of the work function of these metals in metal/BN-MoS2 contacts. These findings may prove to be instrumental in the future design of new MoS2-based FETs with ohmic contact or p-type character.

In-situ fabrication of MoSi2/SiC–Mo2C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo2C barrier layer at high temperature

International Nuclear Information System (INIS)

Liu, Jun; Gong, Qianming; Shao, Yang; Zhuang, Daming; Liang, Ji

2014-01-01

MoSi 2 /SiC–Mo 2 C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo 2 C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi 2 /SiC layer on the upper part of Mo 2 C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo 2 C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi 2 /SiC composite layer.

Phase relations in the systems M2MoO4-Cr2(MoO4)3-Zr(MoO4)2 (M=Li, Na, or Rb)

International Nuclear Information System (INIS)

Bazarov, B.G.; Chimitova, O.D.; Bazarova, Ts.T.; Arkhincheeva, S.I.; Bazarova, Zh.G.

2008-01-01

Phase equilibria in the systems M 2 MoO 4 -Cr 2 (MoO 4 ) 3 -Zr(MoO 4 ) 2 (M=Li, Na, or Rb) were investigated by X-ray powder diffraction analysis, DTA, and IR spectroscopy. The subsolidus structure of the phase diagrams of the systems under study was established. Two phases are formed in the Rb 2 MoO 4 -Cr 2 (MoO 4 ) 3 -Zr(MoO 4 ) 2 system with the molar ratios of the starting components equal to 5:1:1 (S 2 ) and 1:1:1 (S 1 ). Proceeding from isostructural character of Rb 5 FeHf(MoO 4 ) 6 and S 2 , the unit cell parameters are determined for S 2 [ru

Motor development in 3-month-old healthy term-born infants is associated with cognitive and behavioural outcomes at early school age.

Science.gov (United States)

Hitzert, Marrit M; Roze, Elise; Van Braeckel, Koenraad N J A; Bos, Arend F

2014-09-01

To determine whether motor development at 3 months of age is associated with cognitive, motor, and behavioural outcomes in healthy children at early school age. In this cohort study, we included 74 term-born, healthy children (44 males, 30 females; median gestational age 40.1 wks, range 38.0-42.6 wks). From video recordings (median 12.9 wks, range 9.3-18.6 wks), we assessed the quality of fidgety movements, and calculated a motor optimality score. At school age (median 5 y 11 mo, range 5 y 8 mo-7 y 6 mo), we performed detailed cognitive, motor, and behavioural assessments. We examined whether aspects of motor development were associated with functional outcomes. An age-adequate motor repertoire, in particular the presence of antigravity, midline leg, and manipulation movements, was related to poorer cognition, whereas variable finger postures was related to better cognition. Children with a monotonous concurrent motor repertoire had better ball skills but experienced more behavioural problems. The presence of antigravity movements tended to be associated with abnormal recognition (odds ratio [OR] 4.4, 95% confidence interval [CI], 0.9-21; R(2) =0.17; p=0.070), where the absence of variable finger postures was associated with borderline and abnormal visual-spatial perception (OR 20, 95% CI, 1.7-238; R(2) =0.39; p=0.018). Detailed aspects of motor development at 3 months of age are associated with cognition and behaviour, but not with motor outcome, in healthy children at early school age. Our findings suggest that early motor development may be the basis for later cognitive and behavioural performance. Since the associations were only moderate, possible environmental influences should be acknowledged. © 2014 Mac Keith Press.

Influencia de la composición y tratamiento térmico sobre el comportamiento a fluencia de aceros ferrítico-martensíticos del tipo 9Cr1MoVNb utilizados en calderas supercríticas

Directory of Open Access Journals (Sweden)

Gutiérrez Urrutia, I.

2000-06-01

Full Text Available In the present investigation, creep behaviour on various ferritic-martensitic steels (type 9Cr1MoVNb from last generation were studied. They’re amply used as high pressure and temperature tubes in supercritical boilers for advanced thermoelectric plant. The material used was produced with vacuum high frecuency induction furnace hot-rolling followed by normalizing plus and tempering heat treatments. Creep testing carry out with different stress (also constant lower than yield strength (σ < Re and temperatures at 600±50ºC. Influence by variation of some chemical elements (B, Ti, V, Nb, V, C, as well assessment Larson-Miller, Manson-Haferd and Orr-Sherby-Dorn parameters, they’re likewise studied.

Se estudia el comportamiento a fluencia de varios aceros ferrítico-martensíticos de última generación, del tipo 9Cr1MoVNb, que son ampliamente utilizados como tubos presurizados de alta temperatura en calderas supercríticas para centrales térmicas avanzadas de producción de energía eléctrica. El material utilizado fue fabricado en hornos de inducción de alta frecuencia y al vacío, laminado en caliente y posteriormente aplicado diferentes tratamientos térmicos de Normalizado y Revenido. En los ensayos de fluencia se aplicaron diferentes y ctes. σ < Re y temperaturas de 550, 600 y 650º C. La influencia de la variación de determinados elementos (C, N, V, Nb, Ti, B de su composición química así como observar los valores que toman los parámetros de Larson-Miller, Manson-Haferd y Orr-Sherby-Dorn, son asimismo contemplados.

The Effect of Hold Time on Creep-Fatigue in 9Cr-1Mo

Energy Technology Data Exchange (ETDEWEB)

Oh, Tae Young; Kim, Dae Whan; Kim, Yong Wan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Baek, Kyoung Ho [Chungnam National University, Daejeon (Korea, Republic of)

2009-05-15

9Cr-1Mo steel is a candidate material for reactor vessel for VHTR. Because 9Cr-1Mo steel has a good mechanical properties and a lower thermal expansion coefficient than austenitic stainless steel. The reactor vessel of VHTR is operated at about 450 .deg. C. At this temperature, fatigue occurs during start-up and cool-down, and creep occurs during normal operation. Creep-fatigue damage by the interaction between fatigue and creep is an important factor that limits VHTR reactor vessel life. In this study, Effect of hold time on low cycle fatigue behavior of 9Cr-1Mo at 600 .deg. C was investigated in air.

The Effect of Hold Time on Creep-Fatigue in 9Cr-1Mo

International Nuclear Information System (INIS)

Oh, Tae Young; Kim, Dae Whan; Kim, Yong Wan; Baek, Kyoung Ho

2009-01-01

9Cr-1Mo steel is a candidate material for reactor vessel for VHTR. Because 9Cr-1Mo steel has a good mechanical properties and a lower thermal expansion coefficient than austenitic stainless steel. The reactor vessel of VHTR is operated at about 450 .deg. C. At this temperature, fatigue occurs during start-up and cool-down, and creep occurs during normal operation. Creep-fatigue damage by the interaction between fatigue and creep is an important factor that limits VHTR reactor vessel life. In this study, Effect of hold time on low cycle fatigue behavior of 9Cr-1Mo at 600 .deg. C was investigated in air

Phase formation in the Li2MoO4–Rb2MoO4–Fe2(MoO4)3 system and crystal structure of a novel triple molybdate LiRb2Fe(MoO4)3

International Nuclear Information System (INIS)

Khal'baeva, Klara M.; Solodovnikov, Sergey F.; Khaikina, Elena G.; Kadyrova, Yuliya M.; Solodovnikova, Zoya A.; Basovich, Olga M.

2013-01-01

X-ray investigation of solid state interaction of the components in the Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system was carried out, and a subsolidus phase diagram of the said system was constructed. The subsystem Rb 2 MoO 4 –LiRbMoO 4 –RbFe(MoO 4 ) 2 was shown to be non-quasiternary. Formation of a novel triple molybdate LiRb 2 Fe(MoO 4 ) 3 was established, conditions of solid state synthesis and crystallization of the compound were found. Its crystal structure (orthorhombic, space group Pnma, Z=4, a=24.3956(6), b=5.8306(1), c=8.4368(2) Å) represents a new structure type and includes infinite two-row ribbons ([Fe(MoO 4 ) 3 ] 3− ) ∞ parallel to the b axis and composed of FeO 6 octahedra, terminal Mo(3)O 4 tetrahedra, and bridge Mo(1)O 4 and Mo(2)O 4 tetrahedra connecting two or three FeO 6 octahedra. The ribbons are connected to form 3D framework via corner-sharing LiO 4 tetrahedra. Rubidium cations are 11- and 13-coordinated and located in cavities of this heterogeneous polyhedral framework. - Graphical abstract: Exploring the Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system showed its partial non-quasiternarity and revealed a new compound LiRb 2 Fe(MoO 4 ) 3 which was structurally studied. - Highlights: • The Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system study revealed a new compound LiRb 2 Fe(MoO 4 ) 3 . • Its structure of a new type includes ribbons of FeO 6 octahedra and MoO 4 tetrahedra. • The ribbons are connected into a 3D framework via corner-sharing LiO 4 tetrahedra

Y, ¿Cómo lo hacen? familias homoparentales con niños en Lima : constitución y estrategias de crianza y socialización. Estudio de caso de familias de clase media y media alta en distritos de Lima Metropolitana y el Callao

OpenAIRE

Ríos Anaya, María Patricia del Rosario

2017-01-01

Este trabajo se propone investigar, de forma exploratoria, cómo es que las familias homoparentales en Lima logran constituirse como tales a la luz de un entorno que las desconoce, de la falta de amparo legal y de las persistentes actitudes que revelan poca tolerancia frente a homosexuales. Hemos realizado entrevistas a profundidad a 9 miembros adultos de 7 familias homparentales - 6 de ellas lideradas por lesbianas y 1 lideradas por gays-.Uno de los principales resultados es que parejas ho...

Changes in the composition, structure and friction property of sputtered MoS2 films by LEO environment exposure

International Nuclear Information System (INIS)

Gao, Xiaoming; Hu, Ming; Sun, Jiayi; Fu, Yanlong; Yang, Jun; Liu, Weimin; Weng, Lijun

2015-01-01

Highlights: • Sputtered MoS 2 films were exposed in real low earth orbit (LEO) environment. • LEO exposure resulted in the oxidation and S loss of MoS 2 film surface. • Depth affected by the LEO exposure was limited within 10 nm. • The exposed MoS 2 film exhibited a slight increase in friction coefficient at initial sliding stage. - Abstract: Radio frequency-sputtered MoS 2 films had been exposed for 43.5 h in real low earth orbit (LEO) space environment by a space environment exposure device (SEED) aboard China Shenzhou-7 manned spaceship. The composition, morphology, phase structure and friction property of the exposed films were investigated using X-ray photoelectron spectroscope (XPS), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), X-ray energy-dispersive spectroscopy (EDS) and ball-on-disk tribometer. XRD and EDS results revealed that the as-deposited MoS 2 films were characterized by a MoS x O y phase structure, in which x and y values were determined to be ∼0.65 and 1.24, respectively. XPS analysis revealed that due to space atomic oxygen attack, the film surface was oxidized to MoO 3 and MoS x O y with higher O concentration, while the partial S was lost. However, the affected depth was restricted within the surface layer because of protective function of the oxidation layer. As a result, the friction coefficient only exhibited a slight increase at initial stage of sliding friction

Creep-fatigue-environment interaction of 9Cr-1Mo-V-Nb steel

International Nuclear Information System (INIS)

Shibata, Hiroyuki; Ishikawa, Akiyoshi; Asada, Yasuhide

1996-01-01

An extension of the creep-fatigue damage model has been conducted in the present study. The original damage model has been developed to the predict the creep-fatigue life of 9Cr-1Mo-V-Nb steel (Modified 9Cr-1Mo steel) in a very high vacuum environment. The present study is to extend an applicability of the model to the creep-fatigue damage accumulation in the air environment. (orig.)

Production of AA2124/MoSi2/25p composites and effect of heat treatment on their microstructure, hardness and compression properties

Directory of Open Access Journals (Sweden)

Piyadeh, Fatemeh

2014-12-01

Full Text Available AA2124/25vol%MoSi2 composites were processed by two powder metallurgy routes: high energy ball milling of the reinforcement and alloy powder (B composite and wet blending with cyclohexane (W composite, both followed by extrusion to achieve full consolidation. As-extruded and heat treated composite bars were studied microstructurally and mechanically (hardness and compression tests under quasistatic loading. Microstructure and fracture profiles were observed by scanning electron microscopy and the reaction products formed in the matrix were identified by energy-dispersive X-ray spectroscopy and X-ray diffraction analysis. The results show that for both composites, the hardness of the specimens in solution and aged condition was higher than in the as-extruded condition. The hardness of the B composite was higher than that of the W composite whereas the age-hardenability of the B composite was significantly lower than that of the W composite. After heat treatments, small diffusion reaction phases appeared at the interface between matrix and reinforcements. Compressive yield strength and the ultimate strength of both composites improved considerably after the artificial ageing. The composite fracture surfaces exhibited microscopically a ductile appearance that consisted of dimples in the matrix and a fragile fracture of the MoSi2 particulates.En este trabajo se procesaron materiales compuestos AA2124/25vol% MoSi2 mediante dos rutas pulvimetalúrgicas: mezcla de refuerzo y matriz mediante molino de bolas de alta energía (compuesto B y mezcla húmeda con ciclohexano (compuesto W. Ambos polvos compuestos se consolidaron por extrusión. Los materiales recién extruidos y después de tratados térmicamente se estudiaron desde el punto de vista microestructural y mecánico (dureza y compresión bajo carga cuasiestática. Las microestructuras y los perfiles de fractura se observaron por microscopía electrónica de barrido y los productos de reacci

Multiple temperature effects on up-conversion fluorescences of Er3+-Y b3+-Mo6+ codoped TiO2 and high thermal sensitivity

Directory of Open Access Journals (Sweden)

B. S. Cao

2015-08-01

Full Text Available We report multiple temperature effects on green and red up-conversion emissions in Er3+-Y b3+-Mo6+ codoped TiO2 phosphors. With increasing temperature, the decrease of the red emission from 4F9/2→4I15/2, the increase of green emission from 2H11/2→4I15/2 and another unchanged green emission from 4S3/2→4I15/2 were simultaneously observed, which are explained by steady-state rate equations analysis. Due to different evolution with temperature of the two green emissions, higher thermal sensitivity of optical thermal sensor was obtained based on the transitions with the largest fluorescence intensity ratio. Two parameters, maximum theoretical sensitivity (Smax and optimum operating temperature (Tmax are given to describe thermal sensing properties of the produced sensors. The intensity ratio and energy difference ΔE of a pair of energy levels are two main factors for the sensitivity and accuracy of sensors, which should be referred to design sensors with optimized sensing properties.

99Mo production by 100Mo(n,2n)99Mo using accelerator neutrons

International Nuclear Information System (INIS)

Sato, Nozomi; Kawabata, Masako; Nagai, Yasuki; Hashimoto, Kazuyuki; Hatsukawa, Yuichi; Saeki, Hideya; Motoishi, Shoji; Kin, Tadahiro; Konno, Chikara; Ochiai, Kentaro; Takakura, Kosuke; Minato, Futoshi; Iwamoto, Osamu; Iwamoto, Nobuyuki; Hashimoto, Shintaro

2013-01-01

We proposed a new route to produce a medical radioisotope 99 Mo by the 100 Mo(n,2n) 99 Mo reaction using accelerator neutrons. A high-quality 99 Mo with a minimum level of radioactive waste can be obtained by the proposed reaction. The decay product of 99 Mo, 99m Tc, is separated from 99 Mo by the sublimation method. The proposed route could bring a major breakthrough in the solution of ensuring a constant and reliable supply of 99 Mo. (author)

Na2MoO2As2O7

Directory of Open Access Journals (Sweden)

Raja Jouini

2012-12-01

Full Text Available Disodium molybdenum dioxide diarsenate, Na2MoO2As2O7, has been synthesized by a solid-state reaction. The structure is built up from MoAs2O12 linear units sharing corners to form a three-dimensional framework containing tunnels running along the a-axis direction in which the Na+ cations are located. In this framework, the AsV atoms are tetrahedrally coordinated and form an As2O7 group. The MoVI atom is displaced from the center of an octahedron of O atoms. Two Na+ cations are disordered about inversion centres. Structural relationships between different compounds: A2MoO2As2O7 (A = K, Rb, AMOP2O7 (A = Na, K, Rb; M = Mo, Nb and MoP2O7 are discussed.

¿Y, cómo se hacen?

Directory of Open Access Journals (Sweden)

Juan Ruiz

2015-01-01

Full Text Available El mundo de los dibujos animados es producto de la imaginación, de la fantasía que vuela en los sueños de los hombres de cualquier edad. El artículo relata la forma en cómo estos simpáticos personajes, que vemos a diario en el cine o la televisión, pueden moverse tan libremente y con tanto desenfado. Se parte de la idea o argumento, el guionista narra la historia de lo que será el animado. Luego el director con un dibujante trazan las escenas principales de la historia (storyboard o guión dibujado se discute con los artistas y realizadores del filme; una vez aprobado este se perfila el diseño de los personajes, se realiza la escenografía (maquetas de ser necesario. Se hacen los parlamentos o diálogos de los personajes para que actores(as pongan las voces y sigue el proceso más fino y técnico.

Preparation of MoB and MoB-MoSi2 composites by combustion synthesis in SHS mode

International Nuclear Information System (INIS)

Yeh, C.L.; Hsu, W.S.

2007-01-01

Combustion synthesis in the mode of self-propagating high-temperature synthesis (SHS) was carried out in the Mo-B and Mo-B-Si systems for the preparation of molybdenum boride MoB and the composite of MoB-MoSi 2 from elemental powder compacts. Under a preheating temperature above 150 deg. C , the reaction of Mo with boron in the sample compact of Mo:B = 1:1 is characterized by a planar combustion front propagating in a self-sustaining and steady manner. As the preheating temperature or sample compaction density increased, combustion temperature was found to increase and the propagation rate of the combustion front was correspondingly enhanced. Moreover, the XRD analysis provides evidence of yielding nearly single-phase α-MoB from the Mo-B sample at equiatomic stoichiometry. In the synthesis of MoB-MoSi 2 composites, the starting stoichiometry of the Mo-B-Si powder compact was varied so as to produce the final composites containing 20-80 mol% MoB. It was also found the increase of flame-front velocity and combustion temperature with increasing MoB content formed in the composite. The composition analysis by XRD shows excellent conversion from the Mo-B-Si powder compact to the MoB-MoSi 2 composite through the SHS reaction; that is, in addition to a small amount of Mo 5 Si 3 , the as-synthesized composite is composed entirely of MoB and MoSi 2

Syntheses, structures, and properties of Ag4(Mo2O5)(SeO4)2(SeO3) and Ag2(MoO3)3SeO3

International Nuclear Information System (INIS)

Ling Jie; Albrecht-Schmitt, Thomas E.

2007-01-01

Ag 4 (Mo 2 O 5 )(SeO 4 ) 2 (SeO 3 ) has been synthesized by reacting AgNO 3 , MoO 3 , and selenic acid under mild hydrothermal conditions. The structure of this compound consists of cis-MoO 2 2+ molybdenyl units that are bridged to neighboring molybdenyl moieties by selenate anions and by a bridging oxo anion. These dimeric units are joined by selenite anions to yield zigzag one-dimensional chains that extended down the c-axis. Individual chains are polar with the C 2 distortion of the Mo(VI) octahedra aligning on one side of each chain. However, the overall structure is centrosymmetric because neighboring chains have opposite alignment of the C 2 distortion. Upon heating Ag 4 (Mo 2 O 5 )(SeO 4 ) 2 (SeO 3 ) looses SeO 2 in two distinct steps to yield Ag 2 MoO 4 . Crystallographic data: (193 K; MoKα, λ=0.71073 A): orthorhombic, space group Pbcm, a=5.6557(3), b=15.8904(7), c=15.7938(7) A, V=1419.41(12), Z=4, R(F)=2.72% for 121 parameters with 1829 reflections with I>2σ(I). Ag 2 (MoO 3 ) 3 SeO 3 was synthesized by reacting AgNO 3 with MoO 3 , SeO 2 , and HF under hydrothermal conditions. The structure of Ag 2 (MoO 3 ) 3 SeO 3 consists of three crystallographically unique Mo(VI) centers that are in 2+2+2 coordination environments with two long, two intermediate, and two short bonds. These MoO 6 units are connected to form a molybdenyl ribbon that extends along the c-axis. These ribbons are further connected together through tridentate selenite anions to form two-dimensional layers in the [bc] plane. Crystallographic data: (193 K; MoKα, λ=0.71073 A): monoclinic, space group P2 1 /n, a=7.7034(5), b=11.1485(8), c=12.7500(9) A, β=105.018(1) V=1002.7(2), Z=4, R(F)=3.45% for 164 parameters with 2454 reflections with I>2σ(I). Ag 2 (MoO 3 ) 3 SeO 3 decomposes to Ag 2 Mo 3 O 10 on heating above 550 deg. C. - Graphical abstract: A view of the one-dimensional [(Mo 2 O 5 )(SeO 4 ) 2 (SeO 3 )] 4- chains that extend down the c-axis in the structure of Ag 4 (Mo 2 O 5 )(SeO 4

Development on UO3-K2O and MoO3-K2O binary systems and study of UO2MoO4-MoO3 domain within UO3-MoO3-K2O ternary system

International Nuclear Information System (INIS)

Dion, C.; Noel, A.

1983-01-01

This paper confirms the previous study on the MoO 3 -K 2 O system, and constitutes a clarity of the UO 3 -K 2 O system. Four distinct uranates VI with alkaline metal/uranium ratio's 2, 1, 0,5 and 0,285 exist. Preparation conditions and powder diffraction spectra of these compounds are given. Additional informations relative to K 2 MoO 4 allotropic transformations are provided. Study of UO 2 MoO 4 -K 2 MoO 4 diagram has brought three new phases into prominence: (B) K 6 UMo 4 O 18 incongruently melting point, (E) K 2 UMo 2 O 10 congruently melting and (F) K 2 U 3 Mo 4 O 22 incongruently melting point. Within MoO 3 -K 2 MoO 4 -UO 2 MoO 4 ternary system, no new phase is found. The general appearance of ternary liquidus and crystallization fields of several compounds are given. These three new compounds become identified with these of UO 2 MoO 4 -Na 2 MoO 4 binary system [fr

3d-4p transitions in the soft X-ray spectra of Mo XIV and of isoelectronic Y to Ag ions from a low-inductance vacuum spark

International Nuclear Information System (INIS)

Klapisch, M.; Mandelbaum, P.; Schwob, J.L.; Bar-Shalom, A.; Schweitzer, N.

1981-04-01

Eight lines of 3d 10 4s - 3d 9 4s4p and 3d 10 4p-3d 9 4p 2 transitions of CuI-like Y XI to Ag XIX ions are identified in the 30-80 A range of spectra emitted from a low-inductance vacuum spark. Identification is based on isoelectronic analysis and comparison with ab-initio relativistic calculations. In the present paper is analyzed the spectra of Mo XIV

Wssv y temperatura, inmunoestimulantes, vitaminas... ¿cómo se relaciona todo?

OpenAIRE

Rodriguez, Jenny; Echeverría, Fabrizio; Sonneholznher, Stanislaus; Molina, César; Gullian, Mariel

2001-01-01

WSSV y temperatura, inmunoestimulantes, vitaminas... ¿Cómo se relaciona todo? Los experimentos desarrollados a la fecha indican que a temperatura de 33°C disminuye tanto la prevalencia (porcentaje de animales positivos) como la intensidad de la infección en juveniles y en larvas (Boletín Septiembre 15).

Scalable Patterning of MoS2 Nanoribbons by Micromolding in Capillaries.

Science.gov (United States)

Hung, Yu-Han; Lu, Ang-Yu; Chang, Yung-Huang; Huang, Jing-Kai; Chang, Jeng-Kuei; Li, Lain-Jong; Su, Ching-Yuan

2016-08-17

In this study, we report a facile approach to prepare dense arrays of MoS2 nanoribbons by combining procedures of micromolding in capillaries (MIMIC) and thermolysis of thiosalts ((NH4)2MoS4) as the printing ink. The obtained MoS2 nanoribbons had a thickness reaching as low as 3.9 nm, a width ranging from 157 to 465 nm, and a length up to 2 cm. MoS2 nanoribbons with an extremely high aspect ratio (length/width) of ∼7.4 × 10(8) were achieved. The MoS2 pattern can be printed on versatile substrates, such as SiO2/Si, sapphire, Au film, FTO/glass, and graphene-coated glass. The degree of crystallinity of the as-prepared MoS2 was discovered to be adjustable by varying the temperature through postannealing. The high-temperature thermolysis (1000 °C) results in high-quality conductive samples, and field-effect transistors based on the patterned MoS2 nanoribbons were demonstrated and characterized, where the carrier mobility was comparable to that of thin-film MoS2. In contrast, the low-temperature-treated samples (170 °C) result in a unique nanocrystalline MoSx structure (x ≈ 2.5), where the abundant and exposed edge sites were obtained from highly dense arrays of nanoribbon structures by this MIMIC patterning method. The patterned MoSx was revealed to have superior electrocatalytic efficiency (an overpotential of ∼211 mV at 10 mA/cm(2) and a Tafel slope of 43 mV/dec) in the hydrogen evolution reaction (HER) when compared to the thin-film MoS2. The report introduces a new concept for rapidly fabricating cost-effective and high-density MoS2/MoSx nanostructures on versatile substrates, which may pave the way for potential applications in nanoelectronics/optoelectronics and frontier energy materials.

Holey Reduced Graphene Oxide Coupled with an Mo2 N-Mo2 C Heterojunction for Efficient Hydrogen Evolution.

Science.gov (United States)

Yan, Haijing; Xie, Ying; Jiao, Yanqing; Wu, Aiping; Tian, Chungui; Zhang, Xiaomeng; Wang, Lei; Fu, Honggang

2018-01-01

An in situ catalytic etching strategy is developed to fabricate holey reduced graphene oxide along with simultaneous coupling with a small-sized Mo 2 N-Mo 2 C heterojunction (Mo 2 N-Mo 2 C/HGr). The method includes the first immobilization of H 3 PMo 12 O 40 (PMo 12 ) clusters on graphite oxide (GO), followed by calcination in air and NH 3 to form Mo 2 N-Mo 2 C/HGr. PMo 12 not only acts as the Mo heterojunction source, but also provides the Mo species that can in situ catalyze the decomposition of adjacent reduced GO to form HGr, while the released gas (CO) and introduced NH 3 simultaneously react with the Mo species to form an Mo 2 N-Mo 2 C heterojunction on HGr. The hybrid exhibits superior activity towards the hydrogen evolution reaction with low onset potentials of 11 mV (0.5 m H 2 SO 4 ) and 18 mV (1 m KOH) as well as remarkable stability. The activity in alkaline media is also superior to Pt/C at large current densities (>88 mA cm -2 ). The good activity of Mo 2 N-Mo 2 C/HGr is ascribed to its small size, the heterojunction of Mo 2 N-Mo 2 C, and the good charge/mass-transfer ability of HGr, as supported by a series of experiments and theoretical calculations. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Elevated-temperature tensile properties of 2 1/4 Cr-1 Mo steel irradiated in the EBR-II, AD-2 experiment

International Nuclear Information System (INIS)

Klueh, R.L.; Vitek, J.M.

1984-01-01

The effect of irradiated on the tensile properties of 2 1/4 Cr-1 Mo steel was determined for specimens irradiation in EBR-II at 390 to 550 0 C. Unirradiated control specimens and specimens aged for 5000 h at the irradiation temperatures were also tested. Irradiation to approximately 9 dpa at 390 0 C increased the strength and decreased the ductility compared with the unirradiated and aged specimens. Softening occurred in samples irradiated and tested at 450, 500, and 550 0 C

Postirradiation fracture toughness tests of ESR alloy HT-9 and modified 9Cr-1Mo alloy from UBR reactor experiments

International Nuclear Information System (INIS)

Hawthorne, J.R.; Reed, J.R.; Sprague, J.A.

1984-01-01

Alloy HT-9 and Modified 9Cr-1Mo are being evaluated for potential applications as first wall materials in magnetic fusion reactors. Objectives of the current research task were to test fatigue-precracked Charpy-V (PCC/sub v/) specimens from representative plates irradiated in the UBR reactor at 149 0 C or 300 0 C, and, to compare the results against postirradiation notch ductility data developed previously for the materials. Both plates represent electroslag refined (ESR) melt processing. PCC/sub v/ specimens of Alloy HT-9 and Modified 9Cr-1Mo alloy were irradiated at 300 0 C and 149 0 C, respectively, to approx.0.8 X 10 20 n/cm 2 , E > 0.1 MeV. During this period, postirradiation tests for fracture toughness were completed and results compared to notch ductility determinations from standard Charpy-V (C/sub v/) specimens irradiated in the same reactor experiments. Fracture surface examinations by SEM are also reported

Study on the influence of nickel and Al{sub 2}O{sub 3} support on MoS{sub 2} as hydrodenitrogenation catalysts

Energy Technology Data Exchange (ETDEWEB)

Hein, J.; Hrabar, A.; Gutierrez, O.Y.; Lercher, J.A. [Technische Univ. Muenchen, Garching (Germany). Catalysis Research Center

2012-07-01

Alumina-supported Mo and Ni-Mo catalysts as well as an unsupported NiMo catalyst were characterized and tested in the hydrodenitrogenation (HDN) of quinoline in the presence of dibenzothiophene (DBT). The supported catalysts had a well dispersed MoS{sub 2} phase with an average stacking degree around two and slabs length below 10 nm. The unsupported NiMo sulfide catalyst exhibited long, multistacked MoS{sub 2} slabs and contained segregated Ni{sub x}S{sub y} phases. The formation of the Ni-Mo-S phase in both Ni containing catalysts was verified by X-ray absorption spectroscopy, whereas the concentration of coordinatively unsaturated sites was higher for the supported Mo and Ni-Mo catalysts than for the unsupported one. All catalysts were active in the HDN of quinoline and hydrodesulfurization of DBT. The catalytic activity increased in the order Mo/Al{sub 2}O{sub 3} < NiMo/unsupported < Ni-Mo/Al{sub 2}O{sub 3}. Thus, the influence on the catalytic activity of the promoter metal Ni is more important than the presence of a support due to the formation of the Ni-Mo-S phase (more active than MoS{sub 2}). (orig.)

Hydrothermal Synthesis of MoO2 and Supported MoO2 Cata-lysts for Oxidative Desulfurization of Dibenzothiophene

Institute of Scientific and Technical Information of China (English)

Wang Danhong; Zhang Jianyong; Liu Ni; Zhao Xin; Zhang Minghui

2014-01-01

A novel method for obtaining spherical MoO2 nanoparticles and SiO2-Al2O3 supported MoO2 by hydrothermal reduction of Mo (VI) species was studied. The obtained MoO2 catalysts show very high catalytic activity in the oxidative desulfurization (ODS) process. The effect of hydrothermal temperature and crystallization temperature on ODS activity was investigated. The ODS activity of supported MoO2 catalysts with various MoO2 contents were also investigated. The mecha-nism for formation of MoO2 involving oxalic acid was proposed.

Stress-controlled inelastic behavior of modified 9 Cr-1 Mo steel at elevated temperatures

International Nuclear Information System (INIS)

Taguchi, Kosei.

1989-01-01

Interest in the ferritic steels of higher chromium concentration has increased recently because of an economical combination of mechanical and corrosion properties at elevated temperatures. A modified 9 Cr-1 Mo ferritic steel, developed in the United States, has been expected as an alternative structural material for fast breeder reactor components, in which Type 304 stainless steel or 2.25 Cr-1 Mo steel is currently used. For application of this material to the structural components, a lot of work has been done to develop evaluation methods for the deformation behavior and strength properties. The authors have studied the inelastic behavior and the creep-fatigue properties of modified 9 Cr-1 Mo steel at elevated temperatures, and proposed a constitutive equation and a creep-fatigue damage equation based on the overstress concept. In this paper, the applicability is discussed of the constitutive equation to stress-controlled inelastic behavior, such as creep strain hardening and stress cycling

Synthesis of MoS2 and MoO2 for their applications in H2 generation and lithium ion batteries: a review

International Nuclear Information System (INIS)

Zhao Yufei; Zhang Yuxia; Yang Zhiyu; Yan Yiming; Sun Kening

2013-01-01

Scientists increasingly witness the applications of MoS 2 and MoO 2 in the field of energy conversion and energy storage. On the one hand, MoS 2 and MoO 2 have been widely utilized as promising catalysts for electrocatalytic or photocatalytic hydrogen evolution in aqueous solution. On the other hand, MoS 2 and MoO 2 have also been verified as efficient electrode material for lithium ion batteries. In this review, the synthesis, structure and properties of MoS 2 and MoO 2 are briefly summarized according to their applications for H 2 generation and lithium ion batteries. Firstly, we overview the recent advancements in the morphology control of MoS 2 and MoO 2 and their applications as electrocatalysts for hydrogen evolution reactions. Secondly, we focus on the photo-induced water splitting for H 2 generation, in which MoS 2 acts as an important co-catalyst when combined with other semiconductor catalysts. The newly reported research results of the significant functions of MoS 2 nanocomposites in photo-induced water splitting are presented. Thirdly, we introduce the advantages of MoS 2 and MoO 2 for their enhanced cyclic performance and high capacity as electrode materials of lithium ion batteries. Recent key achievements in MoS 2 - and MoO 2 -based lithium ion batteries are highlighted. Finally, we discuss the future scope and the important challenges emerging from these fascinating materials. (review)

Herramienta para establecer y controlar Iniciativas de Mejora de Procesos con MoProSoft

Directory of Open Access Journals (Sweden)

Dagoberto Cruz Sandoval

2015-02-01

Full Text Available La mejora de procesos software es una disciplina cuya premisa es que un proceso de calidad tiene como consecuencia lógica un producto software de calidad. En México, una industria software emergente y compuesta en su mayoría por micro y pequeñas empresas, ha empezado a incursionar en este tipo de disciplina utilizando el modelo mexicano de mejora de procesos conocido como MoProSoft, sin embargo la carencia de conocimiento y experiencia, hace de este tipo de proyectos algo complicado y desgastante. En el presente trabajo se presenta el desarrollo de un marco de trabajo para las micro y pequeñas empresas desarrolladoras de software en México, el cual es apoyado por una herramienta llamada Kaizen que automatiza las fases básicas de una mejora de procesos: compromiso, evaluación, planeación e implementación basadas en los procesos, actividades, prácticas y roles definidos en MoProSoft. La herramienta tiene como objetivo principal proporcionar apoyo a las micro empresas en las iniciativas de mejora por medio de un marco de actividades automatizadas que guían sus pasos durante la ejecución del programa de mejora. Además, se presenta un caso de estudio y resultados cuantitativos de que con el uso de Kaizen cuatro micro empresas mexicanas vieron mejorados sus procesos de desarrollo de software instaurando las prácticas efectivas definidas por MoProSoft.

Modified 9Cr-1Mo steel for advanced steam generator applications

International Nuclear Information System (INIS)

Brinkman, C.R.; Alexander, D.J.; Maziasz, P.J.

1990-01-01

Results are reported from several types of mechanical property tests conducted on a number of commercial heats of modified 9Cr-1Mo steel. Data from long term creep-rupture tests conducted on base and weldment material were compared with an analytical model which has been shown to give good agreement between measured and predicted values. Weldment material had somewhat inferior creep-rupture strength in comparison to base material due to a soft zone at the edge of the HAZ. Data are presented from elevated temperature tensile and creep-rupture tests conducted n material thermally aged for periods of up to 75,000 h (8.6 years). Some reduction in strength was shown to occur in comparison to unaged material. Models were developed for predicting the reduction in short term elevated temperature tensile and yield strength for material thermally aged in the temperature range of 482 to 704 degree C. Results from Charpy impact tests conducted on material thermally aged at 538 degree C for periods of up to 75,000 h showed an increase in the ductile-brittle transition temperature. Finally, results from transmission electron microscopy studies were presented to explain changes in mechanical properties due to thermal aging. These observations showed that Laves phase precipitation and recovery occurs on prolonged exposure of this alloy in this temperature range. 9 refs

Nanoparticles of superconducting γ-Mo2N and δ-MoN

International Nuclear Information System (INIS)

Gomathi, A.; Sundaresan, A.; Rao, C.N.R.

2007-01-01

We have been able to prepare nanoparticles (∼4 nm diameter) of cubic γ-Mo 2 N by a simple procedure involving the reaction of MoCl 5 with urea at 873 K. The nanoparticles show a superconducting transition around 6.5 K. The γ-Mo 2 N nanoparticles are readily transformed to nanoparticles of δ-MoN with a slightly larger diameter on heating in a NH 3 atmosphere at 573 K. Phase-pure δ-MoN obtained by this means shows a superconducting transition around 5 K. - Graphical abstract: TEM image of the γ-Mo 2 N particles with the inset showing the resistivity of the sample as a function of temperature

In-situ fabrication of MoSi{sub 2}/SiC–Mo{sub 2}C gradient anti-oxidation coating on Mo substrate and the crucial effect of Mo{sub 2}C barrier layer at high temperature

Energy Technology Data Exchange (ETDEWEB)

Liu, Jun [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Gong, Qianming, E-mail: gongqianming@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Shao, Yang; Zhuang, Daming [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); State Key Laboratory of New Ceramics and Fine Processing, Beijing 100084 (China); Liang, Ji [Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Beijing 100084 (China); Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2014-07-01

MoSi{sub 2}/SiC–Mo{sub 2}C gradient coating on molybdenum was in situ prepared with pack cementation process by two steps: (1) carburizing with graphite powder to obtain a Mo{sub 2}C layer on Mo substrate, and (2) siliconizing with Si powder to get a composite MoSi{sub 2}/SiC layer on the upper part of Mo{sub 2}C layer. The microstructure and elemental distribution in the coating were investigated with scanning electron microscopy (SEM), backscattered electron (BSE), energy dispersive spectroscopy (EDS), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Cyclic oxidation tests (at 500 °C, 1200 °C, 1400 °C and 1600 °C) demonstrated excellent oxidation resistance for the gradient composite coating and the mass loss was only 0.23% in 60 min at 1600 °C. XRD, EPMA, thermal dynamic and phase diagram analyses indicated that the Mo{sub 2}C barrier layer played the key role in slowing down the diffusion of C and Si toward inner Mo substrate at high temperature and principally this contributed to the excellent anti-oxidation for Mo besides the outer MoSi{sub 2}/SiC composite layer.

Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

International Nuclear Information System (INIS)

Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

2013-01-01

The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 10 17 ions/cm 2 . The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, Cr x C y phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties

Investigation of phase relationships in subsolidus region of Ln2O3-MoO3-B2O3 systems

International Nuclear Information System (INIS)

Lysanova, C.V.; Dzhurinskij, B.F.; Komova, M.G.; Tananaev, I.V.

1983-01-01

Phase formation in subsolidus region of Ln 2 O 3 -MoO 3 B 2 O 3 systems (Ln-La, Nd) is studied. Three compounds with mixed oxyanions-boratomolybdates of LnMoBO 6 composition (Ln-La, Ce, Pr, Nd), Ln 2 MoB 2 O 9 (Ln-La, Ce, Pr, Nd, Sm, EU, Gde Tb) Ln 6 Mo 3 B 4 0 24 (Ln-Pr, Nd) are revealed and described

Theoretical prediction of high electron mobility in multilayer MoS2 heterostructured with MoSe2

Science.gov (United States)

Ji, Liping; Shi, Juan; Zhang, Z. Y.; Wang, Jun; Zhang, Jiachi; Tao, Chunlan; Cao, Haining

2018-01-01

Two-dimensional (2D) MoS2 has been considered to be one of the most promising semiconducting materials with the potential to be used in novel nanoelectronic devices. High carrier mobility in the semiconductor is necessary to guarantee a low power dissipation and a high switch speed of the corresponding electronic device. Strain engineering in 2D materials acts as an important approach to tailor and design their electronic and carrier transport properties. In this work, strain is introduced to MoS2 through perpendicularly building van der Waals heterostructures MoSe2-MoS2. Our first-principles calculations demonstrate that acoustic-phonon-limited electron mobility can be significantly enhanced in the heterostructures compared with that in pure multilayer MoS2. It is found that the effective electron mass and the deformation potential constant are relatively smaller in the heterostructures, which is responsible for the enhancement in the electron mobility. Overall, the electron mobility in the heterostructures is about 1.5 times or more of that in pure multilayer MoS2 with the same number of layers for the studied structures. These results indicate that MoSe2 is an excellent material to be heterostructured with multilayer MoS2 to improve the charge transport property.

Impact evaluation of different cash-based intervention modalities on child and maternal nutritional status in Sindh Province, Pakistan, at 6 mo and at 1 y: A cluster randomised controlled trial.

Directory of Open Access Journals (Sweden)

Bridget Fenn

2017-05-01

Full Text Available Cash-based interventions (CBIs, offer an interesting opportunity to prevent increases in wasting in humanitarian aid settings. However, questions remain as to the impact of CBIs on nutritional status and, therefore, how to incorporate them into emergency programmes to maximise their success in terms of improved nutritional outcomes. This study evaluated the effects of three different CBI modalities on nutritional outcomes in children under 5 y of age at 6 mo and at 1 y.We conducted a four-arm parallel longitudinal cluster randomised controlled trial in 114 villages in Dadu District, Pakistan. The study included poor and very poor households (n = 2,496 with one or more children aged 6-48 mo (n = 3,584 at baseline. All four arms had equal access to an Action Against Hunger-supported programme. The three intervention arms were as follows: standard cash (SC, a cash transfer of 1,500 Pakistani rupees (PKR (approximately US$14; 1 PKR = US$0.009543; double cash (DC, a cash transfer of 3,000 PKR; or a fresh food voucher (FFV of 1,500 PKR; the cash or voucher amount was given every month over six consecutive months. The control group (CG received no specific cash-related interventions. The median total household income for the study sample was 8,075 PKR (approximately US$77 at baseline. We hypothesized that, compared to the CG in each case, FFVs would be more effective than SC, and that DC would be more effective than SC-both at 6 mo and at 1 y-for reducing the risk of child wasting. Primary outcomes of interest were prevalence of being wasted (weight-for-height z-score [WHZ] < -2 and mean WHZ at 6 mo and at 1 y. The odds of a child being wasted were significantly lower in the DC arm after 6 mo (odds ratio [OR] = 0.52; 95% CI 0.29, 0.92; p = 0.02 compared to the CG. Mean WHZ significantly improved in both the FFV and DC arms at 6 mo (FFV: z-score = 0.16; 95% CI 0.05, 0.26; p = 0.004; DC: z-score = 0.11; 95% CI 0.00, 0.21; p = 0.05 compared to the CG

Synthesis, crystal and electronic structures, and magnetic properties of LiLn{sub 9}Mo{sub 16}O{sub 35} (Ln=La, Ce, Pr, and Nd) compounds containing the original cluster Mo{sub 16}O{sub 36}

Energy Technology Data Exchange (ETDEWEB)

Gougeon, Patrick; Gall, Philippe [UMR CNRS 6226 - ' ' Sciences Chimiques de Rennes' ' , Universite de Rennes 1 - INSA (France); Cuny, Jerome; Gautier, Regis; Le Polles, Laurent [UMR CNRS 6226 - ' ' Sciences Chimiques de Rennes' ' , Ecole Nationale Superieure de Chimie de Rennes (France); Delevoye, Laurent; Trebosc, Julien [UMR CNRS 8181 - UCCS, ENSCL, Universite Lille Nord de France, Villeneuve d' Ascq (France)

2011-12-02

The new compounds LiLn{sub 9}Mo{sub 16}O{sub 35} (Ln=La, Ce, Pr, and Nd) were synthesized from stoichiometric mixtures of Li{sub 2}MoO{sub 4}, Ln{sub 2}O{sub 3}, Pr{sub 6}O{sub 11} or CeO{sub 2}, MoO{sub 3}, and Mo heated at 1600 C for 48 h in a molybdenum crucible sealed under a low argon pressure. The crystal structure, determined from a single crystal of the Nd member, showed that the main building block is the Mo{sub 16}O{sub 36} unit, the Mo{sub 16} core of which is totally new and results from the fusion of two bioctahedral Mo{sub 10} clusters. It can also be viewed as a fragment of an infinite twin chain of edge-sharing Mo{sub 6} octahedra. The Mo{sub 16}O{sub 36} cluster units share some oxygen atoms to form infinite chains running parallel to the b axis, which are separated by the rare-earth and lithium cations. {sup 7}Li-NMR experiments, carried out at high field on the nonmagnetic LiLa{sub 9}Mo{sub 16}O{sub 35}, provided insights into the local environment of the lithium ions. Magnetic susceptibility measurements confirmed the trivalent oxidation state of the magnetic rare-earth cations and indicated the absence of localized moments on the Mo{sub 16} clusters. The electronic structure of the LiLn{sub 9}Mo{sub 16}O{sub 35} compounds was analyzed using molecular and periodic quantum calculations. The study of the molecular orbital diagrams of isolated Mo{sub 16}O{sub 36} models allowed the understanding of this unique metallic architecture. Periodic density functional theory calculations demonstrated that few interactions occur between the Mo{sub 16} clusters, and predicted semiconducting properties for LiLn{sub 9}Mo{sub 16}O{sub 35} as a band gap of 0.57 eV was computed for the lanthanum phase. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Structure of β-TlMo2P3O13

International Nuclear Information System (INIS)

Costentin, G.; Borel, M.M.; Grandin, A.; Leclaire, A.; Raveau, B.

1991-01-01

Thallium molybdenum triphosphate, TlMo 2 P 3 O 13 , M r =679.16, monoclinic, P2 1 /c, a=9.7536 (3), b=19.0640 (16), c=6.3945 (7) A, β=107.099 (7) 0 , V=1136 (2) A 3 , Z=4, D m not measured, D x =4.08 Mg m -3 , λ(MoKα)=0.71073 A, μ=16.90 mm -1 , F(000)=314, T=293 K, 951 reflections, R=0.047, ωR=0.047. The lattice is built up from MoO 6 , PO 4 and P 2 O 7 groups delimiting tunnels where the Tl + ions are located. The title compound is isotyopic with β-KMo 2 P 3 O 13 . (orig.)

High pressure effect on MoS2 and MoSe2 single crystals grown by ...

Indian Academy of Sciences (India)

Unknown

tetrahedral anvil apparatus up to 5 GPa. In this paper we report room temperature resistance mea- surements as a function of pressure on MoS2 and MoSe2 single crystals. In each case the resistance decreases un- der pressure due to an increase in the carrier concentration. 2. Experimental. Single crystals of MoS2 and ...

Synthesis of nitrided MoO{sub 2} and its application as anode materials for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Yoon, Sukeun, E-mail: skyoon@kier.re.kr [New and Renewable Energy Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); Jung, Kyu-Nam; Jin, Chang Soo; Shin, Kyung-Hee [New and Renewable Energy Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of)

2012-09-25

Highlights: Black-Right-Pointing-Pointer Synthesis of nitrided molybdenum oxide by nitridation. Black-Right-Pointing-Pointer Superior cyclability for nitrided molybdenum oxide anodes. Black-Right-Pointing-Pointer Electrochemical reaction behavior of nitrided molybdenum oxide with lithium. - Abstract: Nitrided MoO{sub 2} has been synthesized by hydrothermal processing followed by post-nitridation with NH{sub 3} and investigated as alternative anode materials for rechargeable lithium batteries. Characterization data reveal the presence of molybdenum nitride ({gamma}-Mo{sub 2}N and {delta}-MoN) and molybdenum oxynitride (MoO{sub x}N{sub y}). The nitrided MoO{sub 2} exhibits a capacity of >420 mAh/g after 100 cycles and good rate capability. The improved electrochemical performance of the nitrided MoO{sub 2} compared to that of molybdenum oxide (MoO{sub 2}) is attributed to high electrical conductivity provided by nitrogen doping/or substitution in the oxygen octahedral site of MoO{sub 2} structure.

Laser operated optical features in β-BaTeMo2O9:Cr3+ nanocrystallites

International Nuclear Information System (INIS)

Majchrowski, A.; Jaroszewicz, L.R.; Fedorchuk, A.O.; Kityk, I.V.

2015-01-01

An increase of second order nonlinear optical efficiency was established for Cr 3+ doped β-BaTeMo 2 O 9 (BTMO) nanocrystallites (with sizes varying within up to 150 nm range) under influence of two coherent beams of 532 nm nanosecond pulsed lasers at power densities up to 600 MW/cm 2 . It was found that maximal enhancement of optical second harmonic generation was achieved for BTMO:Cr 3+ nanocrystallites possessing sizes about 60–80 nm. Occurrence of some quasi-periodic space radial grating was observed as well. This is a consequence of competition between the photo-polarization and photo-thermal effects. Band structure simulations within a framework of the norm-conserving pseudopotential were performed. - Highlights: • BMTO nanocrystallites with the sizes 60 nm–120 nm were synthesized. • Photoinduced SHG is found. • The effect is caused by additional photopolarization

Impact of Reduced Graphene Oxide on MoS2 Grown by Sulfurization of Sputtered MoO3 and Mo Precursor Films (Postprint)

Science.gov (United States)

2016-05-26

1,2 intercalation assisted exfoliation,8–11 physical vapor deposition (PVD),12,13 and a wet chemistry approach involving thermal decomposition of a... annealed MoO3, MoS2 films S1 (MoS2 using Mo precursor), S2 (MoS2 using MoO3 precursor), S1r (MoS2 using Mo pre- cursor and rGO), and S2r (MoS2 using...MoO3 precursor and rGO). The annealed MoO3 (a) shows Mo(IV) peaks which are indicative of MoO2, and Mo(VI) peaks that occur when MoO3 is present. Both

Reacciones en estado sólido para el sistema Al-MoO₃ en la fabricación de materiales compuestos Al₂O₃-aluminuros de Mo

Directory of Open Access Journals (Sweden)

Marín, J.

2002-02-01

Full Text Available Ceramic matrix composites reinforced with metallic particles exhibit good mechanical properties. One research line has involved the fabrication of 3A (alumina-aluminide alloys composites via in situ consolidation of aluminum reactive powders mixed with a metallic oxide. In this paper the solid state reactions for the Al-MoO₃ system and the effect of the precursor compositions for obtaining Al₂O₃ composites and intermetallic aluminides are studied. The reactions in vacuum for the 25 °C to 750 °C temperature range, and the microstructural evolution up to 1200 °C were studied. DTA-TG and DSC were used to determine that a heating rate of 1 °C/min at the critical range of 500-600 °C, resulted in controlled aluminothermic reactions. XRD and SEM showed that in the sintered composites a microstructure composed of an Al₂O₃ matrix and a Mo aluminide /metallic Mo dispersed phase was present. The precursor composition affects the dispersed phase in the composite (Mo aluminides and/or metallic Mo, the relative Al₂O₃ /second phase quantities, and the hardness of the composite sintered at 1450 °C.

Los materiales compuestos de matriz cerámica (CMC's de Al₂O₃ reforzados con partículas metálicas tienen propiedades mecánicas muy atractivas. Un área de investigación emergente es la fabricación de compuestos 3A (Alumina-Aluminide-Alloys, mediante la formación in situ de Al₂O₃ reforzada con metal elemental y/o aluminuros del metal, partiendo de polvos de aluminio y de óxidos metálicos. En este trabajo se estudian las reacciones en estado sólido para el sistema Al-MoO₃. Las reacciones de aluminotermia se estudian en vacío para el rango de temperaturas entre 25 °C y 750 °C y su evolución microestructural hasta 1.200 °C. Mediante análisis calorimétrico (DTA-TG y DSC se determinó que para una

Crystallographic and magnetic properties of (Nd,Dy)3Fe27.5(Ti,Mo)1.5 compounds

International Nuclear Information System (INIS)

Han, S.B.; Liu, X.F.; Lv, J.Y.; Peng, J.; Hao, Y.M.; Li, X.J.; Chen, D.F.; Xue, Y.J.; Li, J.H.; Hu, Z.B.

2006-01-01

A systematic study of the formation, structure and magnetic properties of (Nd,Dy) 3 Fe 27.5 (Ti,Mo) 1.5 compounds has been performed. Rietveld analyses of the X-ray patterns of the samples indicate that the concentrations of Ti and Mo affect the formation and structural properties slightly, whereas different rare-earth (Nd and Dy) contents influence them significantly. It is found that high Dy contents make it difficult to form the 3:29-type structures. The Curie temperatures of Nd 2.1 Dy 0.9 Fe 27.5 Ti 1.5- x Mo x decrease monotonically as more Ti was replaced by Mo but their saturation magnetizations remain almost unchanged; in contrast, for Nd 3- y Dy y Fe 27.5 TiMo 0.5 , their saturation magnetizations decrease monotonically with increasing Dy contents while their Curie temperatures are constant

Comparitive study of fluorescence lifetime quenching of rhodamine 6G by MoS2 and Au-MoS2

Science.gov (United States)

Shakya, Jyoti; Kasana, Parath; Mohanty, T.

2018-04-01

Time resolved fluorescence study of Rhodamine 6G (R6G) in the presence of Molybdenum disulfide (MoS2) nanosheets and gold doped MoS2 (Au-MoS2) have been carried out and discussed. We have analyzed the fluorescence decay curves of R6G and it is observed that Au-MoS2 is a better fluorescence lifetime quencher as compare to MoS2 nanosheets. Also, the energy transfer efficiency and energy transfer rate from R6G to MoS2 and Au-MoS2 has been calculated and found higher for Au-MoS2.

Nondestructive testing for microstructural characterization in 9Cr-1Mo ferritic steel towards assessment of fabrication quality and in-service degradation

Energy Technology Data Exchange (ETDEWEB)

Jayakumar, T.; Rao, K.B.S.; Raj, Baldev [Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

1999-07-01

The paper discusses the usefulness of non destructive testing for microstructural characterization in 9Cr-1Mo ferritic steel. Ultrasonic velocity and attenuation measurements and spectral analysis have been used in a complementary way for characterizing Ac{sub 1} and Ac{sub 3} temperatures, amount of martensite and ferrite, dissolution of V{sub 4}C{sub 3} and NbC and formation of {delta}-ferrite. The microstructural degradation occurring due to thermal ageing and creep has also been studied by ultrasonic velocity measurements. Magnetic Barkhausen noise technique has been used for estimating the extent of various regions in heat affected zone (HAZ) of 9Cr-1Mo ferritic steel weldment. The same technique has been used for the assessment of low cycle fatigue damage in 9Cr-1Mo steel. The study establishes that non destructive methods can be used for the assessment of fabrication quality and in service degradation of the components. (author)

¿Cómo estás atención? Cuáles son y cómo se evalúan las redes neuronales de la atención

Directory of Open Access Journals (Sweden)

Fernando Gabriel Luna

2016-01-01

Full Text Available Nuestro sistema cognitivo cuenta con redes neuronales que desarrollan diferentes funciones atencionales para afrontar la complejidad estimular del medio ambiente y adaptar nuestro comportamiento a la naturaleza y exigencia de múltiples situaciones. Las redes de la atención conforman un sistema de estructuras cerebrales específicas conectadas y sincronizadas entre sí que nos permiten orientarnos, alertarnos ante algunas señales, sostener nuestra atención, y seleccionar y controlar ciertos estímulos. A continuación se describe la estructura de estas redes, cómo operan en diversas situaciones, y cómo es posible obtener una medida confiable del rendimiento de cada una de las funciones atencionales.

Scalable Patterning of MoS2Nanoribbons by Micromolding in Capillaries

KAUST Repository

Hung, Yu-Han

2016-07-27

In this study, we report a facile approach to prepare dense arrays of MoS2 nanoribbons by combining procedures of micromolding in capillaries (MIMIC) and thermolysis of thiosalts ((NH4)2MoS4) as the printing ink. The obtained MoS2 nanoribbons had a thickness reaching as low as 3.9 nm, a width ranging from 157 to 465 nm, and a length up to 2 cm. MoS2 nanoribbons with an extremely high aspect ratio (length/width) of ∼7.4 × 108 were achieved. The MoS2 pattern can be printed on versatile substrates, such as SiO2/Si, sapphire, Au film, FTO/glass, and graphene-coated glass. The degree of crystallinity of the as-prepared MoS2 was discovered to be adjustable by varying the temperature through postannealing. The high-temperature thermolysis (1000 °C) results in high-quality conductive samples, and field-effect transistors based on the patterned MoS2 nanoribbons were demonstrated and characterized, where the carrier mobility was comparable to that of thin-film MoS2. In contrast, the low-temperature-treated samples (170 °C) result in a unique nanocrystalline MoSx structure (x ≈ 2.5), where the abundant and exposed edge sites were obtained from highly dense arrays of nanoribbon structures by this MIMIC patterning method. The patterned MoSx was revealed to have superior electrocatalytic efficiency (an overpotential of ∼211 mV at 10 mA/cm2 and a Tafel slope of 43 mV/dec) in the hydrogen evolution reaction (HER) when compared to the thin-film MoS2. The report introduces a new concept for rapidly fabricating cost-effective and high-density MoS2/MoSx nanostructures on versatile substrates, which may pave the way for potential applications in nanoelectronics/optoelectronics and frontier energy materials. © 2016 American Chemical Society.

Ternary CoS{sub 2}/MoS{sub 2}/RGO electrocatalyst with CoMoS phase for efficient hydrogen evolution

Energy Technology Data Exchange (ETDEWEB)

Liu, Yan-Ru; Shang, Xiao [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Gao, Wen-Kun [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580 (China); Dong, Bin, E-mail: dongbin@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580 (China); Chi, Jing-Qi; Li, Xiao; Yan, Kai-Li; Chai, Yong-Ming [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Liu, Yun-Qi, E-mail: liuyq@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Liu, Chen-Guang [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China)

2017-08-01

Highlights: • Ternary CoS{sub 2}/MoS{sub 2}/RGO with CoMoS phase as electrocatalyst for HER was prepared. • CoMoS phase have the metallic nature and highly intrinsic activity for HER. • RGO support ensures good distribution of CoMoS phase and enhances the conductivity. • The introduction of CoMoS and RGO may be a novel strategy for efficient HER of MoS{sub 2}. - Abstract: CoMoS phase with metallic character plays crucial role on enhancing the activity of MoS{sub 2} electrocatalysts for hydrogen evolution reaction (HER). However, only Co atoms located in the edges of MoS{sub 2} can create CoMoS phase, so it is a challenge to obtain CoMoS phase with homogeneous distribution limited by the layered MoS{sub 2} and doping method of Co. Herein, we reported a simple one-pot hydrothermal method to prepare novel ternary CoS{sub 2}/MoS{sub 2}/RGO with CoMoS phase for HER using reduced graphene oxide (RGO) as support. XPS proves the formation of CoMoS phase, implying the enhanced activity for HER. RGO support ensures the well distribution of CoMoS phase and enhances the conductivity of CoS{sub 2}/MoS{sub 2}/RGO. Compared to CoS{sub 2}/RGO, MoS{sub 2}/RGO and CoS{sub 2}/MoS{sub 2}, the obtained CoS{sub 2}/MoS{sub 2}/RGO shows superior activity for HER with an onset overpotential of −80 mV (vs. RHE), small Tafel slope of 56 mV dec{sup −1}, high exchange current density of 11.4 μA cm{sup −2} and rigid electrochemical durability. The enhanced performances for HER may be ascribed to the formation of CoMoS phase with high activity and the existence of RGO support with good electrical conductivitys in ternary CoS{sub 2}/MoS{sub 2}/RGO. Therefore, the introduction of CoMoS phase and RGO into MoS{sub 2} could effectively enhance electrocatalytic properties for HER.

Physicochemical investigation of Bi2MoO6 solid-phase interaction with Sm2MoO6

International Nuclear Information System (INIS)

Khajkina, E.G.; Kovba, L.M.; Bazarova, Zh.G.; Khal'baeva, K.M.; Khakhinov, V.V.; Mokhosoev, M.V.

1986-01-01

Bi 2 MoO 6 -Sm 2 MoO 6 interaction in the temperature range of 700-1000 deg C is studied using X-ray phase analysis and vibrational spectroscopy. Formation of monoclinic solid solutions based on γ'-Bi 2 MoO 6 and B 2-x Sm x MoO 6 varied composition phase with α-Ln 2 MoO 6 structure which homogeneity region extent at 1000 deg C constitutes ∼ 50 mol % (0.7≤x≤1.7) is stated. Crystallographic characteristics of the synthesized phases are determined

Impact of the B2 ordering behavior on the mechanical properties of a FeCoMo alloy

Energy Technology Data Exchange (ETDEWEB)

Turk, C., E-mail: chris.turk@unileoben.ac.at [Montanuniversität Leoben, Department of Physical Metallurgy and Materials Testing, Franz-Josef Straße 18, 8700 Leoben (Austria); Leitner, H.; Kellezi, G. [Böhler Edelstahl GmbH & Co KG, Mariazellerstraße 25, 8605 Kapfenberg (Austria); Clemens, H. [Montanuniversität Leoben, Department of Physical Metallurgy and Materials Testing, Franz-Josef Straße 18, 8700 Leoben (Austria); Gan, W.M.; Staron, P. [German Engineering Materials Science Centre, Helmholtz-Zentrum Geesthacht, D-21502 Geesthacht (Germany); Primig, S. [Montanuniversität Leoben, Department of Physical Metallurgy and Materials Testing, Franz-Josef Straße 18, 8700 Leoben (Austria)

2016-04-26

A Fe - 25 at% Co - 9 at% Mo alloy can be hardened by nm-sized (Fe, Co){sub 7}Mo{sub 6} µ-phase precipitates which is accomplished by solution annealing in the austenite region followed by rapid quenching to room temperature and subsequent aging below the austenite transition temperature. In overaged condition the Mo-content in the remaining matrix drops towards zero and, therefore, the matrix consist of 71 at% Fe and 29 at% Co. The binary Fe-Co system shows a disorder-order, A2↔B2 transition at a critical ordering temperature between 25 at% and 72 at% Co. It is expected that the remaining matrix of an overaged Fe - 25 at% Co - 9 at% Mo alloy also exhibits such an ordering reaction. It will be demonstrated that the formation of a B2 ordered FeCo phase can be delayed or completely prevented by rapid quenching from temperatures above the critical ordering temperature. This has a strong impact on the mechanical properties of this alloy which have been studied by means of tensile, impact toughness and hardness testing. The evidence for a disorder-order transition in this alloy has been given by neutron diffraction as well as high resolution transmission electron microscopy.

Assessment of the optimum degree of Sr{sub 3}Fe{sub 2}MoO{sub 9} electron-doping through oxygen removal: An X-ray powder diffraction and {sup 57}Fe Moessbauer spectroscopy study

Energy Technology Data Exchange (ETDEWEB)

Lopez, Carlos A.; Viola, Maria del C. [Area de Quimica General e Inorganica, Departamento de Quimica, Facultad de Quimica, Bioquimica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700 San Luis (Argentina); Pedregosa, Jose C., E-mail: jpedreg@unsl.edu.ar [Area de Quimica General e Inorganica, Departamento de Quimica, Facultad de Quimica, Bioquimica y Farmacia, Universidad Nacional de San Luis, Chacabuco y Pedernera, 5700 San Luis (Argentina); Mercader, Roberto C., E-mail: mercader@fisica.unlp.edu.ar [Departamento de Fisica, IFLP-CONICET, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, C.C. 67, 1900 La Plata (Argentina)

2010-10-15

We describe the preparation and structural characterization by X-ray powder diffraction (XRPD) and Moessbauer spectroscopy of three electron-doped perovskites Sr{sub 3}Fe{sub 2}MoO{sub 9-{delta}} with Fe/Mo = 2 obtained from Sr{sub 3}Fe{sub 2}MoO{sub 9}. The compounds were synthesized by topotactic reduction with H{sub 2}/N{sub 2} (5/95) at 600, 700 and 800 {sup o}C. Above 800 {sup o}C the Fe/Mo ratio changes from Fe/Mo = 2-1 < Fe/Mo < 2. The structural refinements of the XRPD data for the reduced perovskites were carried out by the Rietveld profile analysis method. The crystal structure of these phases is cubic, space group Fm3-bar m, with cationic disorder at the two different B sites that can be populated in variable proportions by the Fe atoms. The Moessbauer spectra allowed determining the evolution of the different species formed after the treatments at different temperatures and confirm that Fe ions in the samples reduced at 600, 700 and 800 {sup o}C are only in the high-spin Fe{sup 3+} electronic state.

Basic investigation for life assessment technology of modified 9CR-1Mo steel

Energy Technology Data Exchange (ETDEWEB)

Okamura, Hiroyuki [Science Univ. of Tokyo (Japan); Ohtani, Ryuichi [Kyoto Univ. (Japan); Fujii, Kazuya [Japan Power Engineering and Inspection Corp., Tokyo (Japan); Kimura, Kazushige; Ishii, Ryuichi; Fujiyama, Kazunari; Hongo, Shigetada; Iseki, Takashi; Uchida, Hiroshi [Toshiba Corp., Kawasaki, Kanagawa (Japan)

1998-11-01

For the basic study of life assessment technologies for aged components made of mod.9Cr-1Mo steel, specimens were artificially deteriorated by aging, creep and fatigue tests at elevated temperatures. And metallurgical and mechanical properties were examined. The change in the precipitates caused the decrease in toughness. The creep damage in base metal corresponded to the decrease in hardness. The fatigue damage in base metal correlated to the maximum length of a crack among micro-cracks initiated during fatigue cycle. In the welded joint, the creep fracture occurred by the formation and growth of voids in the fine grained region of HAZ near base metal. The creep damage was associated with the increase in both number and area fraction of voids. (orig.)

Low-frequency 1/f noise in MoS2 transistors: Relative contributions of the channel and contacts

Science.gov (United States)

Renteria, J.; Samnakay, R.; Rumyantsev, S. L.; Jiang, C.; Goli, P.; Shur, M. S.; Balandin, A. A.

2014-04-01

We report on the results of the low-frequency (1/f, where f is frequency) noise measurements in MoS2 field-effect transistors revealing the relative contributions of the MoS2 channel and Ti/Au contacts to the overall noise level. The investigation of the 1/f noise was performed for both as fabricated and aged transistors. It was established that the McWhorter model of the carrier number fluctuations describes well the 1/f noise in MoS2 transistors, in contrast to what is observed in graphene devices. The trap densities extracted from the 1/f noise data for MoS2 transistors, are 2 × 1019 eV-1cm-3 and 2.5 × 1020 eV-1cm-3 for the as fabricated and aged devices, respectively. It was found that the increase in the noise level of the aged MoS2 transistors is due to the channel rather than the contact degradation. The obtained results are important for the proposed electronic applications of MoS2 and other van der Waals materials.

Precipitation and impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel during isothermal aging

International Nuclear Information System (INIS)

Han, Jian; Li, Huijun; Barbaro, Frank; Jiang, Laizhu; Zhu, Zhixiong; Xu, Haigang; Ma, Li

2014-01-01

The effect of isothermal aging on precipitation behaviour and Charpy impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel was investigated by means of Thermo-Calc prediction, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Charpy impact toughness testing. The results show that, niobium, vanadium carbides and nitrides, Fe 2 Nb (Laves phase) and Cr 23 C 6 formed after 2 h aging at 800 °C, and the equilibrium solvus temperature of Fe 2 Nb phase increases to above 750 °C, higher than the calculated temperature (730 °C) using Thermo-Calc. After isothermal aging at 750–950 °C, 2 h aging resulted in a decrease in toughness due to the formation of precipitation, especially (Nb,V)(C,N) and Fe 2 Nb. When isothermally aged at 800 °C for up to 24 h, the coarsening rate of Fe 2 Nb particle is much higher than that of (Nb,V)(C,N), and the impact toughness of the steel is dependent on quantity and sizes of (Nb,V)(C,N) and Fe 2 Nb particles

Precipitation and impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel during isothermal aging

Energy Technology Data Exchange (ETDEWEB)

Han, Jian, E-mail: jh595@uowmail.edu.au [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Li, Huijun [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Barbaro, Frank [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); CBMM Technology Suisse, 14, Rue du Rhone, Geneve 1204 (Switzerland); Jiang, Laizhu [Baoshan Iron and Steel Co., Ltd., Shanghai 200431 (China); Zhu, Zhixiong [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Xu, Haigang; Ma, Li [Baoshan Iron and Steel Co., Ltd., Shanghai 200431 (China)

2014-08-26

The effect of isothermal aging on precipitation behaviour and Charpy impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel was investigated by means of Thermo-Calc prediction, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Charpy impact toughness testing. The results show that, niobium, vanadium carbides and nitrides, Fe{sub 2}Nb (Laves phase) and Cr{sub 23}C{sub 6} formed after 2 h aging at 800 °C, and the equilibrium solvus temperature of Fe{sub 2}Nb phase increases to above 750 °C, higher than the calculated temperature (730 °C) using Thermo-Calc. After isothermal aging at 750–950 °C, 2 h aging resulted in a decrease in toughness due to the formation of precipitation, especially (Nb,V)(C,N) and Fe{sub 2}Nb. When isothermally aged at 800 °C for up to 24 h, the coarsening rate of Fe{sub 2}Nb particle is much higher than that of (Nb,V)(C,N), and the impact toughness of the steel is dependent on quantity and sizes of (Nb,V)(C,N) and Fe{sub 2}Nb particles.

Successful labeling of 99mTc-MDP using 99mTc separated from 99Mo produced by 100Mo(n,2n)99Mo

International Nuclear Information System (INIS)

Nagai, Yasuki; Hatsukawa, Yuichi; Kin, Tadahiro; Hashimoto, Kazuyuki; Motoishi, Shoji; Konno, Chikara; Ochiai, Kentaro; Takakura, Kosuke; Sato, Yuichi; Sato, Norihito; Ohta, Akio; Yamabayashi, Hisamichi; Tanase, Masakazu; Fujisaki, Saburo; Kawauchi, Yukimasa; Teranaka, Tomoyuki; Takeuchi, Nobuhiro; Igarashi, Takashi

2011-01-01

We have for the first time succeeded in separating 99m Tc from a MoO 3 sample irradiated with accelerator neutrons free from any radioactive impurities and in formulating 99m Tc-methylene diphosphonate ( 99 mTc-MDP). 99 Mo, the mother nuclide of 99m Tc, was produced by the 100 Mo(n,2n) 99 Mo reaction using about 14 MeV neutrons provided by the 3 H(d,n) 4 He reaction at the Fusion Neutronics Source of Japan Atomic Energy Agency. The 99m Tc was separated from 99 Mo by sublimation and its radionuclide purity was confirmed to be higher than 99.99% by γ-spectroscopy. The labeling efficiency of 99m Tc-MDP was shown to be higher than 99% by thin-layer chromatography. These values exceed the United States Pharmacopeia requirements for a fission product, 99 Mo. Consequently, a 99m Tc radiopharmaceutical preparation formed by using the mentioned 99 Mo can be a promising substitute for the fission product 99 Mo, which is currently produced using a highly enriched uranium target in aging research reactors. A longstanding problem to ensure a reliable and constant supply of 99 Mo in Japan can be partially mitigated. (author)

Electrical characteristics of multilayer MoS2 FET's with MoS2/graphene heterojunction contacts.

Science.gov (United States)

Kwak, Joon Young; Hwang, Jeonghyun; Calderon, Brian; Alsalman, Hussain; Munoz, Nini; Schutter, Brian; Spencer, Michael G

2014-08-13

The electrical properties of multilayer MoS2/graphene heterojunction transistors are investigated. Temperature-dependent I-V measurements indicate the concentration of unintentional donors in exfoliated MoS2 to be 3.57 × 10(11) cm(-2), while the ionized donor concentration is determined as 3.61 × 10(10) cm(-2). The temperature-dependent measurements also reveal two dominant donor levels, one at 0.27 eV below the conduction band and another located at 0.05 eV below the conduction band. The I-V characteristics are asymmetric with drain bias voltage and dependent on the junction used for the source or drain contact. I-V characteristics of the device are consistent with a long channel one-dimensional field-effect transistor model with Schottky contact. Utilizing devices, which have both graphene/MoS2 and Ti/MoS2 contacts, the Schottky barrier heights of both interfaces are measured. The charge transport mechanism in both junctions was determined to be either thermionic-field emission or field emission depending on bias voltage and temperature. On the basis of a thermionic field emission model, the barrier height at the graphene/MoS2 interface was determined to be 0.23 eV, while the barrier height at the Ti/MoS2 interface was 0.40 eV. The value of Ti/MoS2 barrier is higher than previously reported values, which did not include the effects of thermionic field emission.

Prediction and Monitoring Systems of Creep-Fracture Behavior of 9Cr-1Mo Steels for Reactor Pressure Vessels

International Nuclear Information System (INIS)

Potirniche, Gabriel; Barlow, Fred D.; Charit, Indrajit; Rink, Karl

2013-01-01

A recent workshop on next-generation nuclear plant (NGNP) topics underscored the need for research studies on the creep fracture behavior of two materials under consideration for reactor pressure vessel (RPV) applications: 9Cr-1Mo and SA-5XX steels. This research project will provide a fundamental understanding of creep fracture behavior of modified 9Cr-1Mo steel welds for through modeling and experimentation and will recommend a design for an RPV structural health monitoring system. Following are the specific objectives of this research project: Characterize metallurgical degradation in welded modified 9Cr-1Mo steel resulting from aging processes and creep service conditions; Perform creep tests and characterize the mechanisms of creep fracture process; Quantify how the microstructure degradation controls the creep strength of welded steel specimens; Perform finite element (FE) simulations using polycrystal plasticity to understand how grain texture affects the creep fracture properties of welds; Develop a microstructure-based creep fracture model to estimate RPVs service life; Manufacture small, prototypic, cylindrical pressure vessels, subject them to degradation by aging, and measure their leak rates; Simulate damage evolution in creep specimens by FE analyses; Develop a model that correlates gas leak rates from welded pressure vessels with the amount of microstructural damage; Perform large-scale FE simulations with a realistic microstructure to evaluate RPV performance at elevated temperatures and creep strength; Develop a fracture model for the structural integrity of RPVs subjected to creep loads; and Develop a plan for a non-destructive structural health monitoring technique and damage detection device for RPVs.

Prediction and Monitoring Systems of Creep-Fracture Behavior of 9Cr-1Mo Steels for Teactor Pressure Vessels

Energy Technology Data Exchange (ETDEWEB)

Potirniche, Gabriel [Univ. of Idaho, Moscow, ID (United States); Barlow, Fred D. [Univ. of Idaho, Moscow, ID (United States); Charit, Indrajit [Univ. of Idaho, Moscow, ID (United States); Rink, Karl [Univ. of Idaho, Moscow, ID (United States)

2013-11-26

A recent workshop on next-generation nuclear plant (NGNP) topics underscored the need for research studies on the creep fracture behavior of two materials under consideration for reactor pressure vessel (RPV) applications: 9Cr-1Mo and SA-5XX steels. This research project will provide a fundamental understanding of creep fracture behavior of modified 9Cr-1Mo steel welds for through modeling and experimentation and will recommend a design for an RPV structural health monitoring system. Following are the specific objectives of this research project: Characterize metallurgical degradation in welded modified 9Cr-1Mo steel resulting from aging processes and creep service conditions; Perform creep tests and characterize the mechanisms of creep fracture process; Quantify how the microstructure degradation controls the creep strength of welded steel specimens; Perform finite element (FE) simulations using polycrystal plasticity to understand how grain texture affects the creep fracture properties of welds; Develop a microstructure-based creep fracture model to estimate RPVs service life; Manufacture small, prototypic, cylindrical pressure vessels, subject them to degradation by aging, and measure their leak rates; Simulate damage evolution in creep specimens by FE analyses; Develop a model that correlates gas leak rates from welded pressure vessels with the amount of microstructural damage; Perform large-scale FE simulations with a realistic microstructure to evaluate RPV performance at elevated temperatures and creep strength; Develop a fracture model for the structural integrity of RPVs subjected to creep loads; and Develop a plan for a non-destructive structural health monitoring technique and damage detection device for RPVs.

Modified 9Cr-1Mo steel for advanced steam generator applications

International Nuclear Information System (INIS)

Brinkman, C.R.; Alexander, D.J.; Maziasa, P.J.

1990-01-01

Results are reported from several types of mechanical property tests conducted on a number of commercial heats of modified 9Cr-1Mo steel. Data from long term creep-rupture tests conducted on base and weldment material were compared with an analytical model which has been shown to give good agreement between measured and predicted values. Weldment material had somewhat inferior creep-rupture strength in comparison to base material due to a soft zone at the edge of the HAZ. Data are presented from elevated temperature tensile and creep-rupture tests conducted on material thermally aged for periods of up to 75,000 h (8.6 years). Some reduction in strength was shown to occur in comparison to unaged material. Models were developed for predicting the reduction in short term elevated temperature tensile and yield strength for material thermally aged in the temperature range of 482 to 704 degrees C. Results from Charpy impact tests conducted on material thermally aged at 538 degrees C for periods of up to 75,000 h show an increase in the ductile-brittle transition temperature

Large-area and highly crystalline MoSe2 for optical modulator

Science.gov (United States)

Yin, Jinde; Chen, Hao; Lu, Wei; Liu, Mengli; Li, Irene Ling; Zhang, Min; Zhang, Wenfei; Wang, Jinzhang; Xu, Zihan; Yan, Peiguang; Liu, Wenjun; Ruan, Shuangchen

2017-12-01

Transition metal dichalcogenides (TMDs) have been successfully used as broadband optical modulator materials for pulsed fiber laser systems. However, the nonlinear optical absorptions of exfoliated TMDs are strongly limited by their nanoflakes morphology with uncontrollable lateral size and thickness. In this work, we provide an effective method to fully explore the nonlinear optical properties of MoSe2. Large-area and high quality lattice MoSe2 grown by chemical vapor deposition method was adopted as an optical modulator for the first time. The large-area MoSe2 shows excellent nonlinear optical absorption with a large modulation depth of 21.7% and small saturable intensity of 9.4 MW cm-2. After incorporating the MoSe2 optical modulator into fiber laser cavity as a saturable absorber, a highly stable Q-switching operation with single pulse energy of 224 nJ is achieved. The large-area MoSe2 possessing superior nonlinear optical properties compared to exfoliated nanoflakes affords possibility for the larger-area two-dimensional materials family as high performance optical devices.

Van der Waals epitaxial growth of MoS2 on SiO2/Si by chemical vapor deposition

KAUST Repository

Cheng, Yingchun; Yao, Kexin; Yang, Yang; LI, LIANG; Yao, Yingbang; Wang, Qingxiao; Zhang, Xixiang; Han, Yu; Schwingenschlö gl, Udo

2013-01-01

Recently, single layer MoS2 with a direct band gap of 1.9 eV has been proposed as a candidate for two dimensional nanoelectronic devices. However, the synthetic approach to obtain high-quality MoS2 atomic thin layers is still problematic

Achieving tunable doping of MoSe2 based devices using GO@MoSe2 heterostructure

Science.gov (United States)

Maji, Tuhin Kumar; Tiwary, Krishna Kanhaiya; Karmakar, Debjani

2017-05-01

Doping nature of MoSe2, one of the promising Graphene analogous device material, can be tuned by controlling the concentration of functional groups in Graphene oxide (GO)@MoSe2 heterostructure. In this study, by first-principles simulation, we have observed that GO can be used as a carrier injection layer for MoSe2, where n or p type carriers are introduced within MoSe2 layer depending on the type and concentration of functional moieties in it. Both n and p-type Schottky barrier height modulations are investigated for different modeled configurations of the heterostructure. This combinatorial heterostructure can be a promising material for future electronic device application.

Ternary alloying study of MoSi2

International Nuclear Information System (INIS)

Yi, D.; Li, C.; Akselsen, O.M.; Ulvensoen, J.H.

1998-01-01

Ternary alloying of MoSi 2 with adding a series of transition elements was investigated by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM), and energy dispersive spectroscopy (EDS). Iron, Co, Ni, Cr, V, Ti, and Nb were chosen as alloying elements according to the AB 2 structure map or the atomic size factor. The studied MoSi 2 base alloys were prepared by the arc melting process from high-purity metals. The EDS analysis showed that Fe, Co, and Ni have no solid solubility in as-cast MoSi 2 , while Cr, V, Ti, and Nb exhibit limited solid solubilities, which were determined to be 1.4 ± 0.7, 1.4 ± 0.4, 0.4 ± 0.1, and 0.8 ± 0.1. Microstructural characterization indicated that Mo-Si-M VIII (M VIII = Fe, Co, Ni) and Mo-Si-Cr alloys have a two-phase as-cast microstructure, i.e., MoSi 2 matrix and the second-phase FeSi 2 , CoSi, NiSi 2 , and CrSi 2 , respectively. In as-cast Mo-Si-V, Mo-Si-Ti, and Mo-Si-Nb alloys, besides MoSi 2 and C40 phases, the third phases were observed, which have been identified to be (Mo, V) 5 Si 3 , TiSi 2 , and (Mo, Nb) 5 Si 3

Benchmark experiment for the cross section of the 100Mo(p,2n)99mTc and 100Mo(p,pn)99Mo reactions

Science.gov (United States)

Takács, S.; Ditrói, F.; Aikawa, M.; Haba, H.; Otuka, N.

2016-05-01

As nuclear medicine community has shown an increasing interest in accelerator produced 99mTc radionuclide, the possible alternative direct production routes for producing 99mTc were investigated intensively. One of these accelerator production routes is based on the 100Mo(p,2n)99mTc reaction. The cross section of this nuclear reaction was studied by several laboratories earlier but the available data-sets are not in good agreement. For large scale accelerator production of 99mTc based on the 100Mo(p,2n)99mTc reaction, a well-defined excitation function is required to optimise the production process effectively. One of our recent publications pointed out that most of the available experimental excitation functions for the 100Mo(p,2n)99mTc reaction have the same general shape while their amplitudes are different. To confirm the proper amplitude of the excitation function, results of three independent experiments were presented (Takács et al., 2015). In this work we present results of a thick target count rate measurement of the Eγ = 140.5 keV gamma-line from molybdenum irradiated by Ep = 17.9 MeV proton beam, as an integral benchmark experiment, to prove the cross section data reported for the 100Mo(p,2n)99mTc and 100Mo(p,pn)99Mo reactions in Takács et al. (2015).

¿Y eso cómo se come? La interculturalidad y las comidas familiares

Directory of Open Access Journals (Sweden)

Francisco Adame Gómez

2015-10-01

Full Text Available Las comidas familiares son un ritual común a muchas culturas pero único en cómo se parametriza en cada una de ellas. Cada una se rige por unas normas no explícitas que todos los comensales, al compartir la misma cultura, conocen. Sin embargo, cuando alguien de una cultura diferente participa en una comida de este tipo, pueden producirse malentendidos y choques culturales fruto del desconocimiento de esas normas. Estas situaciones incómodas pueden solucionarse trabajando la interculturalidad en el aula de E/LE. La actividad que proponemos parte de una reflexión sobre la cultura propia para compararla con la cultura meta, seguida de una divertida simulación en la que nuestros alumnos tendrán que ponerse en la piel de un español. Tiene una duración de unos 120 minutos y está pensada para el nivel B2, aunque es adaptable a cualquier otro nivel.

Interstitial Mo-Assisted Photovoltaic Effect in Multilayer MoSe2 Phototransistors.

Science.gov (United States)

Kim, Sunkook; Maassen, Jesse; Lee, Jiyoul; Kim, Seung Min; Han, Gyuchull; Kwon, Junyeon; Hong, Seongin; Park, Jozeph; Liu, Na; Park, Yun Chang; Omkaram, Inturu; Rhyee, Jong-Soo; Hong, Young Ki; Yoon, Youngki

2018-03-01

Thin-film transistors (TFTs) based on multilayer molybdenum diselenide (MoSe 2 ) synthesized by modified atmospheric pressure chemical vapor deposition (APCVD) exhibit outstanding photoresponsivity (103.1 A W -1 ), while it is generally believed that optical response of multilayer transition metal dichalcogenides (TMDs) is significantly limited due to their indirect bandgap and inefficient photoexcitation process. Here, the fundamental origin of such a high photoresponsivity in the synthesized multilayer MoSe 2 TFTs is sought. A unique structural characteristic of the APCVD-grown MoSe 2 is observed, in which interstitial Mo atoms exist between basal planes, unlike usual 2H phase TMDs. Density functional theory calculations and photoinduced transfer characteristics reveal that such interstitial Mo atoms form photoreactive electronic states in the bandgap. Models indicate that huge photoamplification is attributed to trapped holes in subgap states, resulting in a significant photovoltaic effect. In this study, the fundamental origin of high responsivity with synthetic MoSe 2 phototransistors is identified, suggesting a novel route to high-performance, multifunctional 2D material devices for future wearable sensor applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Measurement and Estimation of the 99Mo Production Yield by 100Mo(n,2n)99Mo

Science.gov (United States)

Minato, Futoshi; Tsukada, Kazuaki; Sato, Nozomi; Watanabe, Satoshi; Saeki, Hideya; Kawabata, Masako; Hashimoto, Shintaro; Nagai, Yasuki

2017-11-01

We, for the first time, measured the yield of 99Mo, the mother nuclide of 99mTc used in nuclear medicine diagnostic procedures, produced by the 100Mo(n,2n)99Mo reaction with accelerator neutrons. The neutrons with a continuous energy spectrum from the thermal energy up to about 40 MeV were provided by the C(d,n) reaction with 40 MeV deuteron beams. It was proved that the 99Mo yield agrees with that estimated by using the latest data on neutrons from the C(d,n) reaction and the evaluated cross section of the 100Mo(n,2n)99Mo reaction given in the Japanese Evaluated Nuclear Data Library. On the basis of the agreement, a systematic calculation was carried out to search for an optimum condition that enables us to produce as much 99Mo as possible with a good 99Mo/100Mo value from an economical point of view. The calculated 99Mo yield from a 150 g 100MoO3 sample indicated that about 30% of the demand for 99Mo in Japan can be met with a single accelerator capable of 40 MeV, 2 mA deuteron beams. Here, by referring to an existing 18F-fluorodeoxyglucose (FDG) distribution system we assumed that 99mTc radiopharmaceuticals formed after separating 99mTc from 99Mo can be delivered to hospitals from a radiopharmaceutical company within 6 h. The elution of 99mTc from 99Mo twice a day would meet about 50% of the demand for 99Mo.

Near-Infrared Spectroscopy of the Y0 WISEP J173835.52+273258.9 and the Y1 WISE J035000.32-565830.2: the Importance of Non-Equilibrium Chemistry

Science.gov (United States)

Leggett, S. K.; Tremblin, P.; Saumon, D.; Marley, M. S.; Morley, Caroline V.; Amundsen, D. S.; Baraffe, I.; Chabrier, G.

2016-01-01

We present new near-infrared spectra, obtained at Gemini Observatory, for two Y dwarfs: WISE J035000.32-565830.2 (W0350) and WISEP J173835.52+273258.9 (W1738). A FLAMINGOS-2 R = 540 spectrum was obtained for W0350, covering 1.0 < ? micrometer < 1.7, and a cross-dispersed GNIRS R = 2800 spectrum was obtained for W1738, covering 0.993 - 1.087 micrometer, 1.191 - 1.305 micrometer, 1.589 - 1.631 micrometer, and 1.985 - 2.175 micrometer, in four orders. We also present revised Y JH photometry for W1738, using new NIRI Y and J imaging, and a re-analysis of the previously published NIRI H band images. We compare these data, together with previously published data for late-T and Y dwarfs, to cloud-free models of solar metallicity, calculated both in chemical equilibrium and with disequilibrium driven by vertical transport. We find that for the Y dwarfs the non-equilibrium models reproduce the near-infrared data better than the equilibrium models. The remaining discrepancies suggest that fine-tuning the CH4/CO and NH3/N2 balance is needed. Improved trigonometric parallaxes would improve the analysis. Despite the uncertainties and discrepancies, the models reproduce the observed near-infrared spectra well. We find that for the Y0, W1738, T(sub eff) = 425 +/- 25K and log g = 4.0 +/- 0.25, and for the Y1, W0350, T(sub eff) = 350 +/- 25K and log g = 4.0 +/- 0.25. W1738 may be metal-rich. Based on evolutionary models, these temperatures and gravities correspond to a mass range for both Y dwarfs of 3 - 9 Jupiter masses, with W0350 being a cooler, slightly older, version of W1738; the age of W0350 is 0.3 - 3 Gyr, and the age of W1738 is 0.15 - 1 Gyr.

Rational synthesis of high nuclearity Mo/Fe/S clusters: the reductive coupling approach in the convenient synthesis of (Cl(4)-cat)(2)Mo(2)Fe(6)S(8)(PR(3))(6) [R = Et, (n)Pr, (n)Bu] and the new [(Cl(4)-cat)(2)Mo(2)Fe(2)S(3)O(PEt(3))(3)Cl]-1/2(Fe(PEt(3))(2)(MeCN)(4)) and (Cl(4)-cat)(2)Mo(2)Fe(3)S(5)(PEt(3))(5) clusters.

Science.gov (United States)

Han, J; Koutmos, M; Ahmad, S A; Coucouvanis, D

2001-11-05

-Fe, Fe-Fe, Mo-S, Fe-S bonds. The oxidation states of the metal atoms in this neutral cluster (X) have been assigned as Mo(IV)Mo(III)Fe(II)Fe(II)Fe(III) based on zero-field Mössbauer and magnetic measurement. All Fe atoms are high spin and two of the three Fe-Fe distances are found at 2.4683(9) A and 2.4721(9) A.

Investigation on the age of mineralization in the Sungun porphyry Cu-Mo deposit, NW Iran with a regional metallogenic perspective

Science.gov (United States)

Simmonds, Vartan; Moazzen, Mohssen; Mathur, Ryan

2016-04-01

The Sungun porphyry copper deposit (PCD) is located in NW Iran, neighbouring several other PCDs and prospects in the region and the Lesser Caucasus (south Armenia). It lies on the Urumieh-Dokhtar magmatic arc (UDMA), which formed through the northeast-ward subduction of the Neo-Tethyan oceanic crust beneath the Central Iranian plate during late-Mesozoic and early-Cenozoic [1], and hosts the porphyry copper metallogenic belt of Iran. The Sungun PCD is the second largest deposit in Iran with ore reserves of about 850 Mt at 0.62 wt% Cu and 0.01 wt% Mo and probable reserves over 1Gt. The monzonitic to quartz monzonitic porphyry stock intruded the upper Cretaceous carbonates and Eocene volcano-sedimentary rocks. It produced a skarn-type mineralization at its contact zone with the carbonate rocks, as well as vast hydrothermal alteration zones and porphyry-type Cu and Mo mineralization. The zircon U-Pb age of the host porphyry stock is about 22.5±0.4 to 20.1±0.4 Ma [2]. Re-Os dating of four molybdenite separates from this PCD shows ages ranging between 22.9±0.2 to 21.7±0.2 Ma, with an average of 22.57±0.2 Ma, corresponding to the early Miocene (Aquitanian). These ages indicate that both the porphyry stock and the Cu-Mo mineralization are post-collisional events, similar to many other deposits and prospects in NW and central Iran and south Armenia, and the mineralization occurred shortly after the emplacement of the host stock, corresponding better to the ages obtained from the marginal parts of the stock. Magmatism and mineralization in Sungun coincides with the third metallogenic epoch in the Lesser Caucasus (Eocene to Miocene; [3]), though it is considerably younger than all of the dated PCDs and prospects in the south Armenia. It also postdates Cu-Mo mineralizations in the Saheb Divan (35 Ma), Qaradagh batholith (31.22±0.28 to 25.19±0.19 Ma), as well as Haft Cheshmeh PCD (28.18±0.42 to 27.05±0.37 Ma) in NW Iran, while it seems to be coeval with the Kighal

Double molybdates in Li2MoO4 - Na2MoO4 - H2O system at 25 grad C

International Nuclear Information System (INIS)

Karov, Z.G.; Mirzoev, R.S.; Makitova, D.D.; Zhilova, S.B.; Podnek, A.G.; Urusova, R.Kh.

1989-01-01

Solubility in Li 2 MoO 4 - Na 2 MoO 4 - H 2 O system at 25 deg C is first stuied. Formation of two Li 2 MoO 4 · Na 2 MoO 4 · 4H 2 O and Li 2 MoO 4 · 3Na 2 MoO 4 · 12H 2 O compounds in a system is ascertained. Density, refractive index, viscosity, surface tension, electric conductivity and pH of saturated solutions are determined. Isothermes of mole volume, equivalent and reduced electric conductivity and seeming mole volume of salts sum in solutions are calculated. All these properties adequtely confirm the character of components interaction in a system determined by solubility method. Crystallhydrates of binary molybdates are separated, indentified and studied

Effect of Cr and Mo on strain ageing behaviour of low carbon steel

International Nuclear Information System (INIS)

Pereloma, E.V.; Bata, V.; Scott, R.I.; Smith, R.M.

2010-01-01

This work explores the effects of Cr (0.26-0.74 wt%) and Mo (0.09-0.3 wt%) additions on the kinetics of strain ageing process in low carbon steel. The strain ageing behaviour of the steels was investigated by using tensile tests and transmission electron microscopy. The results have shown that Mo-alloyed steels undergo the same four stages of ageing as unalloyed low carbon steel, whereas Cr-alloyed steels exhibit only three stages of ageing. At the same time, the addition of Mo accelerates the ageing response, while alloying with Cr reduces the rate of strain ageing by ∼3 times in comparison with non-alloyed low carbon steel. It especially delays the offset of Stage III. This is explained by the reduction of carbon content in ferrite due to the enrichment of cementite with Cr leading to the reduction of its equilibrium solubility in ferrite.

Effect of Cr and Mo on strain ageing behaviour of low carbon steel

Energy Technology Data Exchange (ETDEWEB)

Pereloma, E.V., E-mail: elenap@uow.edu.au [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Northfields Avenue, Wollongong, NSW 2522 (Australia); Bata, V. [Department of Materials Engineering, Monash University (Australia); Scott, R.I.; Smith, R.M. [BlueScope Steel Limited, Port Kembla (Australia)

2010-04-25

This work explores the effects of Cr (0.26-0.74 wt%) and Mo (0.09-0.3 wt%) additions on the kinetics of strain ageing process in low carbon steel. The strain ageing behaviour of the steels was investigated by using tensile tests and transmission electron microscopy. The results have shown that Mo-alloyed steels undergo the same four stages of ageing as unalloyed low carbon steel, whereas Cr-alloyed steels exhibit only three stages of ageing. At the same time, the addition of Mo accelerates the ageing response, while alloying with Cr reduces the rate of strain ageing by {approx}3 times in comparison with non-alloyed low carbon steel. It especially delays the offset of Stage III. This is explained by the reduction of carbon content in ferrite due to the enrichment of cementite with Cr leading to the reduction of its equilibrium solubility in ferrite.

Proyecciones Vintage: Mad Men y Cuéntame cómo pasó / Vintage Projections: Mad Men and Cuéntame cómo pasó

Directory of Open Access Journals (Sweden)

Laura García Pousa

2016-09-01

Full Text Available Las series de televisión han puesto a prueba la capacitación del drama mediante la construcción de un discurso propio y diferenciado, que las convierte en uno de los referentes artísticos contemporáneos de mayor expansión. En este artículo acudimos a su estudio específico como nuevos artefactos culturales que trabajan con múltiples realidades y niveles narrativos creando ficciones capaces de aglutinar éxito comercial y nuevas parcelas audiovisuales que generan reflexiones sobre la representación de la memoria histórica. Aunque distantes en su concepción, desarrollo, producción y tratamiento, nos centramos en Mad Men (AMC: 2007- y en Cuéntame cómo pasó (Grupo Ganga: 2001- por su importante trabajo de contextualización dramática donde la cultura popular, la visión mediatizada y los mitos se convierten en constantes de sus narraciones. El estudio comparativo de dos nudos dramáticos como son el asesinato de John F. Kennedy en Mad Men y el atentado contra Carrero Blanco en Cuéntame cómo pasó nos permitirá iniciar y profundizar en las formas argumentales, discursivas y estéticas de ambas producciones dentro de su desarrollo en continuidad como obras de ficción de largo recorrido.Palabras clave: series de televisión, ficción, memoria, historia, representación, Mad Men, Cuéntame cómo pasó, cultura popular, identidad.AbstractTelevision series have challenged the drama by constructing a personal and differentiated discourse, turning it into one of the contemporary artistic genres experiencing the greatest expansion at the moment. In this article, we’ve undertaken the study of such series as new cultural artifacts that work with multiple realities and narrative levels, creating fictions that garner commercial success, and new audiovisual parcels that generate reflections on the representations of historical memory. Although distinct in their conception, development, production and material, we will focus on the series Mad

Low-frequency 1/f noise in MoS2 transistors: Relative contributions of the channel and contacts

International Nuclear Information System (INIS)

Renteria, J.; Jiang, C.; Samnakay, R.; Rumyantsev, S. L.; Goli, P.; Balandin, A. A.; Shur, M. S.

2014-01-01

We report on the results of the low-frequency (1/f, where f is frequency) noise measurements in MoS 2 field-effect transistors revealing the relative contributions of the MoS 2 channel and Ti/Au contacts to the overall noise level. The investigation of the 1/f noise was performed for both as fabricated and aged transistors. It was established that the McWhorter model of the carrier number fluctuations describes well the 1/f noise in MoS 2 transistors, in contrast to what is observed in graphene devices. The trap densities extracted from the 1/f noise data for MoS 2 transistors, are 2 × 10 19  eV −1 cm −3 and 2.5 × 10 20  eV −1 cm −3 for the as fabricated and aged devices, respectively. It was found that the increase in the noise level of the aged MoS 2 transistors is due to the channel rather than the contact degradation. The obtained results are important for the proposed electronic applications of MoS 2 and other van der Waals materials

Anti-bombing insensitivity life of molybdenum cathode doped with La2O3 and Y2O3

International Nuclear Information System (INIS)

Wang Jinshu; Wang Yiman; Zhou Meiling

2006-01-01

Anti-bombing insensitivity of La 2 O 3 -Y 2 O 3 -Mo secondary emitter has been studied in this paper. The variation of maximum secondary emission coefficient δ max with time was measured. The cathode after life experiment was analyzed by means of HRM, SEM, EDS and XRD. The results showed that δ max of La 2 O 3 -Y 2 O 3 -Mo cathode operating at 1100 deg. C under continuous electron bombardment of 300 W/cm 2 was still about 2.5 after 1000 h operation, indicating that this kind of cathode had good anti-bombing insensitivity. In the internal part of the cathode, RE 2 O 3 (rare earth oxide) and molybdenum grains distributed alternately and there existed a certain relationship between crystallographic orientation of RE 2 O 3 and that of molybdenum. It was found that a RE 2 O 3 layer was formed on the surface after operation. The high δ max of La 2 O 3 -Y 2 O 3 -Mo cathode was related to the RE 2 O 3 layer on the surface and the amount of nanosized La 2 O 3 particles on the Y 2 O 3 layer

Processing of Mo-Si-B intermetallics by extrusion and oxidation properties of the extruded Tl-MoSi2-MoB Systems

International Nuclear Information System (INIS)

Summers, Eric

1999-01-01

An extrusion process was developed that is able to consistently produce large quantities of Mo-Si-B rods without the presence of defects. Binder removal from the extruded rods was studied in detail and it was determined that heating rates on the order of 0.02degree/minute (1.2degree/hour) are necessary to remove the binder without the formation of defects. This low heating rate resulted in debinding times in excess of 70 hours (∼ 3 days). Wicking was investigated as a means to decrease the time necessary for binder removal. Using 0.05microm alumina powder as a wicking agent, binder removal times were reduced to 10 hours with heating rates up to 1degree/minute employed without defect formation. Once the extrusion process was complete the oxidation properties of the Tl-MoSi 2 -MoB extruded phase assemblage was investigated. It was determined that this composition exhibits catastrophic oxidation or pesting in the temperature range of 660--760 C, resulting in the material turning to dust. Outside of this temperature range the composition is oxidatively stable. Continuous mass measurements were taken at 1,300, 1,450, and 1,600 C to determine the oxidation rate constants of this material. Parabolic rate constants of 6.9 x 10 -3 , 1.3 x 10 -3 , and 9.1 x 10 -3 mg 2 /cm 4 /hr were determined for 1,300, 1,450, and 1,600 C respectively

In-situ Raman and X-ray photoelectron spectroscopic studies on the pitting corrosion of modified 9Cr-1Mo steel in neutral chloride solution

Science.gov (United States)

Ramya, S.; Nanda Gopala Krishna, D.; Mudali, U. Kamachi

2018-01-01

In-situ Raman and X-ray photoelectron spectroscopic studies were performed for the identification of native and corroded surface oxide layers of modified 9Cr-1Mo steel. The Raman data obtained for native oxide layer of modified 9Cr-1Mo steel revealed that it was mainly composed of oxides of Fe and Cr. The presence of alloying element Mo was found to be less significant in the native oxide film. The oxides of Cr were dominant at the surface and were found to be decreasing closer to metal/oxide layer interface. The changes in the chemical composition of the native films upon in-situ pitting during potentiostatic polarization experiment were characterized by in-situ Raman analysis. The corrosion products of potentiostatically polarized modified 9Cr-1Mo steel was composed of dominant Fe (III) phases viz., γ- Fe2O3, α and γ - FeOOH along with the oxides of chromium. The results from Raman analysis were corroborated with the XPS experiments on as received and pitted samples of modified 9Cr-1Mo steel specimens. It was observed that the oxides of Cr and Mo contributed for the stability of the surface layer by forming Cr2O3 and MoO3. Also, the study attempted to find out the intermediate corrosion products inside the metastable pits to account for the pseudo passive behavior of modified 9Cr-1Mo steel in 0.1 M NaCl solution.

Aspectos bibliográficos del TFG. Cómo citar y componer la bibliografía

OpenAIRE

García Folgado, Mª José; Rodríguez Gonzalo, Carmen

2014-01-01

Este capítulo intenta dar respuesta a una larga serie de preguntas que surgen en la redacción del trabajo de fin de grado (TFG): ¿cómo introducir en el texto las ideas y palabras de los autores consultados? ¿Cómo se citan las palabras de un autor citadas por otro trabajo? ¿Cómo plasmar todo lo que se ha leído? ¿Cómo incluirlo en la bibliografía? ¿Hay que poner lo que se ha leído, pero no se ha usado? ¿Cómo se citan las fuentes de red? ¿Qué hacer si la fuente consultada ti...

Electronic structures of B1 MoN, fcc Mo2N, and hexagonal MoN

International Nuclear Information System (INIS)

Ihara, H.; Kimura, Y.; Senzaki, K.; Kezuka, H.; Hirabayashi, M.

1985-01-01

The electronic structures of B1 MoN, fcc Mo 2 N, and hexagonal MoN were observed by photoelectron spectroscopic measurement. The B1-MoN phase has been predicted to be a high-T/sub c/ superconductor because of a large density of states at Fermi level. The observed electronic structure of the stoichiometric B1-MoN phase is different from that of the real B1-MoN type. The nitrogen excess B1-MoN/sub x/ (x> or =1.3) phase, however, shows the B1-type electronic structure. This is explained by the occurrence of a nitrogen vacancy in the apparent stoichiometric B1 phase and the occupation of the nitrogen vacancy in the nitrogen-excess B1 phase. This property is related to the previously reported low T/sub c/ of the B1-MoN crystals

Stable MoS2 Field-Effect Transistors Using TiO2 Interfacial Layer at Metal/MoS2 Contact

KAUST Repository

Park, Woojin

2017-09-07

Molybdenum disulphide (MoS2) is an emerging 2-dimensional (2D) semiconductor for electronic devices. However, unstable and low performance of MoS2 FETs is an important concern. In this study, inserting an atomic layer deposition (ALD) titanium dioxide (TiO2) interfacial layer between contact metal and MoS2 channel is suggested to achieve more stable performances. The reduced threshold voltage (VTH) shift and reduced series resistance (RSD) were simultaneously achieved.

A first principle Comparative study of electronic and optical properties of 1H –MoS2 and 2H –MoS2

International Nuclear Information System (INIS)

Kumar, Ashok; Ahluwalia, P.K.

2012-01-01

First principle calculations of electronic and optical properties of monolayer MoS 2 , so called 1H –MoS 2 , is performed which has emerged as a new direct band gap semiconductor. Before calculations of the properties of 1H –MoS 2 , we have calculated structural parameters, electronic properties (electronic band structure and electronic density of states) and frequency dependent optical response (real and imaginary part of dielectric function, energy loss function, absorption and reflectance spectra) of 2H –MoS 2 and compared with existing experimental results and found that our calculated results are in very good agreements with experimental results. To compare the dielectric functions of bulk (2H –MoS 2 ) and monolayer (1H –MoS 2 ) phases we have further extended these calculations to the single layer MoS 2 (1H –MoS 2 ) which is analogous to graphene. Structural parameters of 1H –MoS 2 are found very close to its bulk 2H –MoS 2 . We find direct electronic band gap at ‘K’ high symmetry point as compared to indirect band gap in its bulk 2H – MoS2. Our calculated dielectric function for 1H – MoS2 shows structure at nearly same energy positions as compared to 2H – MoS2 with additional structure at 3.8 eV. Also additional well defined energy loss peaks revealing the plasmonic resonances at 15.7 eV and 16.0 eV for E vector perpendicular and parallel to c axis respectively for 1H – MoS2 have been found, which are the signatures of surface plasmons at these energies. -- Highlights: ► Structural parameters of 2H-MoS2 and 1H-MoS2 are nearly identical. ► States around the Fermi energy are mainly due to the metal d states. ► Strong hybridization between Mo-d and S-p states below the Fermi energy has been found. ► Optical spectra of 2H-MoS2 finds very good agreements with experimental optical spectra. ► The band gap is found to be direct for 1H-MoS2 as compared to indirect for 2H-MoS2.

Temperature-Dependent Electrical Properties of Al2O3-Passivated Multilayer MoS2 Thin-Film Transistors

Directory of Open Access Journals (Sweden)

Seok Hwan Jeong

2018-03-01

Full Text Available It is becoming more important for electronic devices to operate stably and reproducibly under harsh environments, such as extremely low and/or high temperatures, for robust and practical applications. Here, we report on the effects of atomic-layer-deposited (ALD aluminum oxide (Al2O3 passivation on multilayer molybdenum disulfide (MoS2 thin-film transistors (TFTs and their temperature-dependent electrical properties, especially at a high temperature range from 293 K to 380 K. With the aid of ultraviolet-ozone treatment, an Al2O3 layer was uniformly applied to cover the entire surface of MoS2 TFTs. Our Al2O3-passivated MoS2 TFTs exhibited not only a dramatic reduction of hysteresis but also enhancement of current in output characteristics. In addition, we investigated the temperature-dependent behaviors of the TFT performance, including intrinsic carrier mobility based on the Y-function method.

Controllable Growth of Monolayer MoS2 and MoSe2 Crystals Using Three-temperature-zone Furnace

Science.gov (United States)

Zheng, Binjie; Chen, Yuanfu

2017-12-01

Monolayer molybdenum disulfide (MoS2) and molybdenum diselenide (MoSe2) have attracted a great attention for their exceptional electronic and optoelectronic properties among the two dimensional family. However, controllable synthesis of monolayer crystals with high quality needs to be improved urgently. Here we demonstrate a chemical vapor deposition (CVD) growth of monolayer MoS2 and MoSe2 crystals using three-temperature-zone furnace. Systematical study of the effects of growth pressure, temperature and time on the thickness, morphology and grain size of crystals shows the good controllability. The photoluminescence (PL) characterizations indicate that the as-grown monolayer MoS2 and MoSe2 crystals possess excellent optical qualities with very small full-width-half-maximum (FWHM) of 96 me V and 57 me V, respectively. It is comparable to that of exfoliated monolayers and reveals their high crystal quality. It is promising that our strategy should be applicable for the growth of other transition metal dichalcogenides (TMDs) monolayer crystals.

Oxidation of atomically thin MoS2 on SiO2

Science.gov (United States)

Yamamoto, Mahito; Cullen, William; Einstein, Theodore; Fuhrer, Michael

2013-03-01

Surface oxidation of MoS2 markedly affects its electronic, optical, and tribological properties. However, oxidative reactivity of atomically thin MoS2 has yet to be addressed. Here, we investigate oxidation of atomic layers of MoS2 using atomic force microscopy and Raman spectroscopy. MoS2 is mechanically exfoliated onto SiO2 and oxidized in Ar/O2 or Ar/O3 (ozone) at 100-450 °C. MoS2 is much more reactive to O2 than an analogous atomic membrane of graphene and monolayer MoS2 is completely etched very rapidly upon O2 treatment above 300 °C. Thicker MoS2 (> 15 nm) transforms into MoO3 after oxidation at 400 °C, which is confirmed by a Raman peak at 820 cm-1. However, few-layer MoS2 oxidized below 400 °C exhibits no MoO3 Raman mode but etch pits are formed, similar to graphene. We find atomic layers of MoS2 shows larger reactivity to O3 than to O2 and monolayer MoS2 transforms chemically upon O3 treatment even below 100 °C. Work supported by the U. of Maryland NSF-MRSEC under Grant No. DMR 05-20741.

Deoxygenation of glycolaldehyde and furfural on Mo2C/Mo(100)

Science.gov (United States)

McManus, Jesse R.; Vohs, John M.

2014-12-01

The desire to produce fuels and chemicals in an energy conscious, environmentally sympathetic approach has motivated considerable research on the use of cellulosic biomass feedstocks. One of the major challenges facing the utilization of biomass is finding effective catalysts for the efficient and selective removal of oxygen from the highly-oxygenated, biomass-derived platform molecules. Herein, a study of the reaction pathways for the biomass-derived platform molecule furfural and biomass-derived sugar model compound glycolaldehyde provides insight into the mechanisms of hydrodeoxygenation (HDO) on a model molybdenum carbide catalyst, Mo2C/Mo(100). Using temperature programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS), it was found that the Mo2C/Mo(100) catalyst was active for selective deoxygenation of the aldehyde carbonyl by facilitating adsorption of the aldehyde in an η2(C,O) bonding configuration. Furthermore, the catalyst showed no appreciable activity for furanic ring hydrogenation, highlighting the promise of relatively inexpensive Mo2C catalysts for selective HDO chemistry.

Microstructure and tribological properties of NiMo/Mo2Ni3Si intermetallic 'in-situ' composites

International Nuclear Information System (INIS)

Gui Yongliang; Song Chunyan; Yang Li; Qin Xiaoling

2011-01-01

Research highlights: → Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites was fabricated successfully with Mo-Ni-Si powder blends as the starting materials. Microstructure of the NiMo/Mo 2 Ni 3 Si composites consists of Mo 2 Ni 3 Si primary dendrites, binary intermetallic phase NiMo and small amount of Ni/NiMo eutectics structure. The NiMo/Mo 2 Ni 3 Si composites exhibited high hardness and outstanding tribological properties under room-temperature dry-sliding wear test conditions which were attributed to the covalent-dominant strong atomic bonds and excellent combination of strength and ductility and toughness. - Abstract: Wear resistant NiMo/Mo 2 Ni 3 Si intermetallic 'in-situ' composites with a microstructure of ternary metal silicide Mo 2 Ni 3 Si primary dendritic, the long strip-like NiMo intermetallic phase, and a small amount of Ni/NiMo eutectics structure were designed and fabricated using molybdenum, nickel and silicon elemental powders. Friction and wear properties of NiMo/Mo 2 Ni 3 Si composites were evaluated under different contact load at room-temperature dry-sliding wear test conditions. Microstructure, worn surface morphologies and subsurface microstructure were characterized by OM, XRD, SEM and EDS. Results indicate that NiMo/Mo 2 Ni 3 Si composites have low fiction coefficient, excellent wear resistance and sluggish wear-load dependence. The dominant wear mechanisms of NiMo/Mo 2 Ni 3 Si composites are soft abrasion and slightly superficial oxidative wear.

EFECTO DEL Mo APLICADO POR SUMERSION A SEMILLAS DE ALGODONERO SOBRE LA RESPIRACION DE PLANTILLAS y SU GERMINACION

Directory of Open Access Journals (Sweden)

I Mogilner

1965-01-01

Full Text Available Se trataron semillas de algodonero manteniéndolas sumergidas en: a agua destilada; b sol. de molibdato de sodio 0,05 O/C, y e sol. de molibdato de amonio 0,05 % durante 24 hs. a una temperatura de 30°C, con el objeto de determinar el efecto del elemento Mo sobre la germinación y respiración.Para el ensayo de germinación se realizaron 36 repeticiones de cada variante.Cada repetición consistió en 25 semillas dispuestas en una caja de Petri entre papel de filtro humedecido. Los resultados indican que el Mo tiene un efecto deprimente sobre la germinación, significativo al 1 %. La respiración se midió 24. hs. después de terminado el tratamiento sobre radículas y cotiledones separadamente. El Mo aumenta la respiración de las radículas en forma altamente significativa. Sobre los cotiledones el Mo, acompañado por el catión sodio, deprime la respiración, y acompañado por el catión amonio la aumenta.

Microstructural characterization of second phases in X10CrMoVNb9-1 and 12CrMoWCuVNb steels after long steam exposure time at 550 C

International Nuclear Information System (INIS)

Rodak, Kinga; Hernas, Adam; Vodarek, Vlastimil

2015-01-01

Microstructural changes in high alloy (9-12% Cr) creep resistant martensitic X10CrMoVNb9-1 and 12CrMoW . CuVNb steels after 100 000 h of steam exposure at 550 C have been studied using scanning transmission electron microscopy. Precipitates were identified using electron diffraction patterns and energy dispersive X-ray spectroscopy analysis. After long time exposure, a significant coarsening of M 23 C 6 carbides, and intensive precipitation of the coarse Laves phase were observed. Moreover, in the 12CrMoW . CuVNb steel, a low amount of the modified Z-phase particles was detected. The microstructures of the X10Cr . MoVNb9-1 and 12CrMoWCuVNb steels after 100 000 h of exposure differ in several aspects.

Microstructural characterization of second phases in X10CrMoVNb9-1 and 12CrMoWCuVNb steels after long steam exposure time at 550 C

Energy Technology Data Exchange (ETDEWEB)

Rodak, Kinga; Hernas, Adam [Silesian Univ. of Technology, Inst. of Materials Science, Katowice (Poland); Vodarek, Vlastimil [VSB-Technical Univ. of Ostrava (Czech Republic)

2015-07-15

Microstructural changes in high alloy (9-12% Cr) creep resistant martensitic X10CrMoVNb9-1 and 12CrMoW . CuVNb steels after 100 000 h of steam exposure at 550 C have been studied using scanning transmission electron microscopy. Precipitates were identified using electron diffraction patterns and energy dispersive X-ray spectroscopy analysis. After long time exposure, a significant coarsening of M{sub 23}C{sub 6} carbides, and intensive precipitation of the coarse Laves phase were observed. Moreover, in the 12CrMoW . CuVNb steel, a low amount of the modified Z-phase particles was detected. The microstructures of the X10Cr . MoVNb9-1 and 12CrMoWCuVNb steels after 100 000 h of exposure differ in several aspects.

Transfer matrix approach to electron transport in monolayer MoS2/MoO x heterostructures

Science.gov (United States)

Li, Gen

2018-05-01

Oxygen plasma treatment can introduce oxidation into monolayer MoS2 to transfer MoS2 into MoO x , causing the formation of MoS2/MoO x heterostructures. We find the MoS2/MoO x heterostructures have the similar geometry compared with GaAs/Ga1‑x Al x As semiconductor superlattice. Thus, We employ the established transfer matrix method to analyse the electron transport in the MoS2/MoO x heterostructures with double-well and step-well geometries. We also considere the coupling between transverse and longitudinal kinetic energy because the electron effective mass changes spatially in the MoS2/MoO x heterostructures. We find the resonant peaks show red shift with the increasing of transverse momentum, which is similar to the previous work studying the transverse-momentum-dependent transmission in GaAs/Ga1‑x Al x As double-barrier structure. We find electric field can enhance the magnitude of peaks and intensify the coupling between longitudinal and transverse momentums. Moreover, higher bias is applied to optimize resonant tunnelling condition to show negative differential effect can be observed in the MoS2/MoO x system.

Characteristic length scale dependence on conductivity for La2-xErxMo2O9 (0.05 ≤ x ≤ 0.3) oxide ion conductors

Science.gov (United States)

Paul, T.; Ghosh, A.

2016-05-01

Structural property of polycrystalline La2-xErxMo2O9 has been investigated. Rietveld refinements at room temperature of the materials suggest a single phase nature with cubic symmetry (space group P213). The electron density contour plot confirms the nature of different cation-oxygen bonds. Time dependent mean square displacement (√) and the spatial extent of the sub-diffusive motion (√) are evaluated using the linear response theory. The localized hop at O2 and O3 sites is found to be favorable for oxygen ion migration for these systems.

Chemical effects of the (n,γ) reactin in MoCl2

International Nuclear Information System (INIS)

Solache R, M.J.

1979-01-01

A contribution is made in the molybdenum radiochemistry, and the possibility to obtain 99 Mo of high specific activity throught the Szilard-Chalmers effect was explored. MoCl 2 samples were irradiated in the Triga Mark III Reactor of the Mexican Nuclear Center, with an approximated flow of 2.7 x 10 12 neutrons/cm 2 , sec. during 15 minutes, the recoil products of the 99 Mo were separated by column chromatography using Sephadex G-10 resin and one solution of HCl 1.5N as eluant; the MoCl 2 retained in sephadex was oxided to molybdate in order to extract it from the resin, using hydrogen peroxide solution. The two phases radioactivity was measured by gamma spectrophotometry. According to the results the MoCl 2 percentage that remain as such is 17 +- 2%. The study of the temperature effect on the fragments of the (n, γ) reaction in MoCl 2 (thermal annealing) was made heating the irradiated samples during half an hour, to different temperatures; the obtained isocrona curve show that the retention was increment as a value of 31.9% to 155 0 C, that value remain constant until 220 0 C, to higher temperature the complex is decomposed. The MoCl 2 is not very sensitive to the hydrolysis due to the separation method and presents little tendency to the radiolysis, from the enrichment point of view of 99 Mo by the Szilard-Chalmers effect it looks like a good compound since in addition to the mentioned characteristics, the chemical changes under the compound by the (n, γ) reaction is high. (author)

Evaluation of dynamic fracture toughness of cold worked 9Cr-1Mo steel

International Nuclear Information System (INIS)

Sathyanarayanan, S.; Sasikala, G.; Ray, S.K.

2004-01-01

Dynamic J-R curves for cold worked 9Cr-1Mo steel have been estimated from instrumented impact test data at ambient temperature on pre-cracked Charpy specimens using three methods of analysis, namely those by Ray et al., Schindler, and Sreenivasan and Mannan. It is concluded that of these three, Schindler's method is the best suited for the purpose since it gives consistent variations with cold work of dynamic J-R curves and dynamic fracture toughness. Cold work results in substantial degradation in dynamic fracture toughness of 9Cr-1Mo steel

Polyoxometalates paneling through {Mo2O2S2} coordination: cation-directed conformations and chemistry of a supramolecular hexameric scaffold.

Science.gov (United States)

Marrot, Jérôme; Pilette, Marie Anne; Haouas, Mohamed; Floquet, Sébastien; Taulelle, Francis; López, Xavier; Poblet, Josep M; Cadot, Emmanuel

2012-01-25

The chemical system based on the [Mo(2)O(2)S(2)(OH(2))(6)](2+) aqua cation (noted L) and the trivacant [AsW(9)O(33)](9-) polyoxometalate (noted POM) has been investigated. Depending upon the ionic strength and the nature of the alkali cations, these complementary components assemble to yield three different architectures derived as hexamer (1), tetramer (2), and dimer (3). This series of clusters displays the same stoichiometry {POM(6)L(9)}(36-), {POM(4)L(6)}(24-), and {POM(2)L(3)}(12-) for 1, 2, and 3, respectively, and their conditions of formation differ mainly by the nature and the concentration of the alkali cation (from Li to Cs). Structural characterizations of 1 reveal a large hexameric supramolecular scaffold (about 25 Å in diameter), which encloses a large internal hole (about 200 Å(3)) filled by water molecules and alkali cations (Na(+) or K(+)). The hexameric scaffold 1 exhibits a rare flexibility property evidenced in the solid state by two distinct conformations, either eclipsed (1a) or staggered-off (1b). Both conformations appear clearly separated by a large twist angle (~40°) and depend mainly on the composition of the internal hole. Structure of anion 2 shows a tetrahedral arrangement where the four POM units and the six connecting {Mo(2)O(2)S(2)} linkers are located at the corners and at the edges, respectively. The structure of anion 3 corresponds to the simplest arrangement, described as a dimeric association of two POM units linked by three {Mo(2)S(2)O(2)} pillars. Stability of the hexameric scaffold has been investigated in solution by (183)W and (39)K NMR and by UV-vis, showing that stability of 1 depends strongly on the proportion of potassium ions, which interfere through host-guest exchange. Density functional methodology (DFT) has been applied to compute the geometries and energies of dimer (3), tetramer (2) and hexamer (1) based on {AsW(9)O(33)} (POM) and {Mo(2)O(2)S(2)} (L) units. Calculations tend to show that internal cations act

Investigación marítima en salud y seguridad, por qué y cómo?

DEFF Research Database (Denmark)

Jensen, Olaf Chresten

2012-01-01

) Seleccionar algunos problemas en su área de trabajo que deben ser investigados en el campo de la salud ocupacional. 2) Proponer los objetivos de la investigación relacionados con los problemas detectados. 3) Seleccionar los diseños de los estudios adecuados, que deben aplicarse a los objetivos propuestos de...... , analíticos (etiognosis) c) estudios de intervención de análisis (prognosis). C. Comprender cómo los 3 tipos de diseño corresponden a los procedimientos lógicos de diagnóstico en la clínica médica y basada en la evidencia. Objetivos de rendimiento: Al final del curso el estudiante debe ser capaz de: 1......Objetivos de Aprendizaje: A. Conocer cómo la investigación epidemiológica en general, constituye un elemento fundamental de prevención de riesgos laborales. B. Entender los objetivos de los 3 tipos principales de diseño del estudio: a) estudios descriptivos (diagnosis) b) estudios causales...

Long-term strength and allowable stresses of grade 10Kh9MFB and X10CrMoVNb9-1 (T91/P91) chromium heat-resistant steels

Science.gov (United States)

Skorobogatykh, V. N.; Danyushevskiy, I. A.; Schenkova, I. A.; Prudnikov, D. A.

2015-04-01

Currently, grade X10CrMoVNb9-1 (T91, P91) and 10Kh9MFB (10Kh9MFB-Sh) chromium steels are widely applied in equipment manufacturing for thermal power plants in Russia and abroad. Compilation and comparison of tensile, impact, and long-term strength tests results accumulated for many years of investigations of foreign grade X10CrMoVNb9-1, T91, P91, and domestic grade 10Kh9MFB (10Kh9MFB-Sh) steels is carried out. The property identity of metals investigated is established. High strength and plastic properties of steels, from which pipes and other products are made, for operation under creep conditions are confirmed. Design characteristics of long-term strength on the basis of tests with more than one million of hour-samples are determined ( and at temperatures of 500-650°C). The table of recommended allowable stresses for grade 10Kh9MFB, 10Kh9MFB-SH, X10CrMoVNb9-1, T91, and P91 steels is developed. The long-time properties of pipe welded joints of grade 10Kh9MFB+10Kh9MFB, 10Kh9MFB-Sh+10Kh9MFB-Sh, X10CrMoVNb9-1+X10CrMoVNb9-1, P91+P91, T91+T91, 10Kh9MFB (10Kh9MFB-Sh)+X10CrMoVNb9-1(T/P91) steels is researched. The welded joint reduction factor is experimentally determined.

Breast-milk intake of 9-10-mo-old rural infants given a ready-to-use complementary food in South Kivu, Democratic Republic of Congo.

Science.gov (United States)

Owino, Victor O; Bahwere, Paluku; Bisimwa, Ghislain; Mwangi, Christine M; Collins, Steve

2011-06-01

Lipid-based ready-to-use foods are currently used for infant feeding, but their potential effect on breast-milk intake is not well documented. The objective was to assess the breast-milk intake of 9-10-mo-old infants given either a ready-to-use complementary food (RUCF) paste or a standard corn-soy blend (UNIMIX) porridge in South Kivu, Democratic Republic of Congo. Infants were randomly assigned at 6 mo of age to receive either RUCF (n = 700) or UNIMIX (n = 700) for 6 mo. Breast-milk intake was measured at 9-10 mo in a subsample of 58 infants (29 from each group). Mothers received a dose of ≈30 g deuterium oxide. Predose and postdose saliva samples were collected from both mothers and infants over 2 wk. Breast-milk intake (g/d) was measured from saliva samples by using infrared spectroscopy. Mean (±SD) breast-milk intake was not significantly (P = 0.69) different between the 2 groups: RUCF (705 ± 236 g/d) and UNIMIX (678 ± 285 g/d). Mean (±SD) nonmilk oral water intakes were 338.3 ± 251.1 and 336.4 ± 227.2 g/d for RUCF and UNIMIX, respectively (P = 0.98). No differences in breast-milk intake were observed between infants consuming either RUCF or UNIMIX. The deuterium-dose-to-the-mother dilution technique is an affordable technique that we recommend for periodic evaluation of breast-milk intake in resource-poor settings. This trial is registered at controlled-trials.com as ISRCTN20267635.

The concentration effect of upconversion luminescence properties in Er3+/Yb3+-codoped Y2(MoO4)3 phosphors

International Nuclear Information System (INIS)

Lu Weili; Cheng Lihong; Sun Jiashi; Zhong Haiyang; Li Xiangping; Tian Yue; Wan Jing; Zheng Yanfeng; Huang Libo; Yu Tingting; Yu Hongquan; Chen Baojiu

2010-01-01

Y 2 (MoO 4 ) 3 :Er 3+ /Yb 3+ phosphors with fixed (varied) Er 3+ and varied (fixed) Yb 3+ concentrations were synthesized by a conventional solid-state reaction. The crystal structure of the phosphors was characterized by means of X-ray diffraction (XRD). Upon 980 nm excitation, very weak blue emission, and strong green and red upconversion emissions centered at 485, 525, 545 and 656 nm were observed. The two-photon process was confirmed to be responsible for both the green and red upconversion emissions. The effects of green upconversion emission intensity ratio ( 2 H 11/2 → 4 I 15/2 versus 4 S 3/2 → 4 I 15/2 ) and the integrated upconversion emission intensity on the Yb 3+ and Er 3+ concentrations were studied.

Heat treatment effects on impact toughness of 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated to 100 dpa

Energy Technology Data Exchange (ETDEWEB)

Klueh, R.L.; Alexander, D.J. [Oak Ridge National Lab., TN (United States)

1997-08-01

Plates of 9Cr-1MoVNb and 12Cr-1MoVW steels were given four different heat treatments: two normalizing treatments were used and for each normalizing treatment two tempers were used. Miniature Charpy specimens from each heat treatment were irradiated to {approx}19.5 dpa at 365{degrees}C and to {approx}100 dpa at 420{degrees}C in the Fast Flux Test Facility (FFTF). In previous work, the same materials were irradiated to 4-5 dpa at 365{degrees}C and 35-36 dpa at 420{degrees}C in FFTF. The tests indicated that prior austenite grain size, which was varied by the different normalizing treatments, had a significant effect on impact behavior of the 9Cr-1MoVNb but not on the 12Cr-1MoVW. Tempering treatment had relatively little effect on the shift in DBTT for both steels. Conclusions are presented on how heat treatment can be used to optimize impact properties.

Heat treatment effects on impact toughness of 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated to 100 dpa

International Nuclear Information System (INIS)

Klueh, R.L.; Alexander, D.J.

1997-01-01

Plates of 9Cr-1MoVNb and 12Cr-1MoVW steels were given four different heat treatments: two normalizing treatments were used and for each normalizing treatment two tempers were used. Miniature Charpy specimens from each heat treatment were irradiated to ∼19.5 dpa at 365 degrees C and to ∼100 dpa at 420 degrees C in the Fast Flux Test Facility (FFTF). In previous work, the same materials were irradiated to 4-5 dpa at 365 degrees C and 35-36 dpa at 420 degrees C in FFTF. The tests indicated that prior austenite grain size, which was varied by the different normalizing treatments, had a significant effect on impact behavior of the 9Cr-1MoVNb but not on the 12Cr-1MoVW. Tempering treatment had relatively little effect on the shift in DBTT for both steels. Conclusions are presented on how heat treatment can be used to optimize impact properties

On the reduction of orthorhombic MoO3 to MoO2

International Nuclear Information System (INIS)

Delannay, F.

1982-01-01

Electron diffraction shows evidence of topotactic orientation relationships between the original MoO 3 crystal and MoO 2 crystals formed under mild reduction conditions. These relationships differ from previously published literature data. A possible mechanism of formation of the [100] strings of edge sharing octahedra in the MoO 2 structure is tentatively proposed. (author)

Solid state reactions of MoO3 and Na2MoO4 with (U.85,Ce.15)O2x

International Nuclear Information System (INIS)

Dahale, N.D.; Keskar, Meera; Singh Mudher, K.D.; Chawla, K.L.

1999-01-01

(U .85 ,Ce .15 )MoO 6-x was prepared by the solid state reactions of (U .85 ,Ce .15 )O 2±x with MoO 3 in air at 600 deg C. Solid state reactions of Na 2 MoO 4 with (U .85 ,Ce .15 )MoO 6.x up to 550 deg C in air led to the formation of Na 2 (U .85 ,Ce .15 )Mo 2 O 10-x and Na 2 (U .85 , Ce .15 ) 2 Mo 3 O 16-x . These compounds were characterised by x-ray and thermal methods. The x-ray powder data of (U .85 , Ce .15 ) MoO 6-x were indexed on monoclinic system whereas, data of Na 2 (U .85 ,Ce .15 ) Mo 2 O 10-x and Na 2 (U .85 ,Ce .15 ) 2 Mo 3 O 16-x were indexed on orthorhombic and monoclinic system respectively. (author)

Investigating the Effect of Glass Ion Release on the Cytocompatibility, Antibacterial Eflcacy and Antioxidant Activity of Y2O3 / CeO2 doped SiO2-SrO-Na2O glasses

Directory of Open Access Journals (Sweden)

Placek L. M.

2018-02-01

Full Text Available The effect on ion release and cytocompatibility of Yttrium (Y and Cerium (Ce are investigated when substituted for Sodium (Na in a 0.52SiO2-0.24SrO-0.24-Na2OMOglass series (where MO= Y2O3 or CeO2. Glass leaching was evaluated through pH measurements and Inductive Coupled Plasma-Optical Emission Spectrometry (ICP-OES analysiswhere the extract pH increased during incubation (11.2 - 12.5. Ion release of Silicon (Si, Na and Strontium (Sr from the Con glass was at higher than that of glasses containing Y or Ce, and reached a limit after 1 day. Ion release from Y and Ce containing glasses reached a maximum of 1800 μg/mL, 1800 μg/mL, and 10 μg/mL for Si, Na, and Sr, respectively. Release of Y and Cewas below the ICP- OES detection limit 75% of bacteria at a 9% extract concentration. Antioxidant capacity (mechanism for neuroprotection was evaluated using the ABTS assay. All glasses had inherent radical oxygen species (ROS scavenging capability with Con reaching 9.5 mMTE.

Thermodynamic properties and behaviour of A2[(UO2)(MoO4)2] compounds with A = Li, Na, K, Rb, and Cs

International Nuclear Information System (INIS)

Lelet, Maxim I.; Suleimanov, Evgeny V.; Golubev, Aleksey V.; Geiger, Charles A.; Depmeier, Wulf; Bosbach, Dirk; Alekseev, Evgeny V.

2014-01-01

Highlights: • Low temperature heat capacity of A 2 [(UO 2 )(MoO 4 ) 2 ] (A = Li, Na, K, Rb, and Cs) series was determined. • Enthalpy of formation of Li 2 [(UO 2 )(MoO 4 ) 2 ] was determined by HF solution calorimetry. • Δ f G° (T = 298 K) of all phases from studied series were calculated. - Abstract: A thermodynamic investigation of five alkali-metal uranyl molybdates of the general formula A 2 [(UO 2 )(MoO 4 ) 2 ], where A = Li, Na, K, Rb, and Cs, was undertaken. The various phases were synthesized by solid-state reaction of ANO 3, with A = Li, Na, K, Rb, or Cs, MoO 3 and γ-UO 3 . The synthetic products were characterized by X-ray powder diffraction and X-ray fluorescence methods. The low-temperature heat capacity, S r °, was measured using adiabatic calorimetry from T = (6 to 335) K. Based on these data, the third law entropy at T = 298.15 K, S°, is (345 ± 1) J · K −1 · mol −1 for Li 2 [(UO 2 )(MoO 4 ) 2 ], (373 ± 1) J · K −1 · mol −1 for Na 2 [(UO 2 )(MoO 4 ) 2 ], (390 ± 1) J · K −1 · mol −1 for K 2 [(UO 2 )(MoO 4 ) 2 ], (377 ± 1) J · K −1 · mol −1 for Rb 2 [(UO 2 )(MoO 4 ) 2 ] and (394 ± 1) J · K −1 · mol −1 for Cs 2 [(UO 2 )(MoO 4 ) 2 ]. The enthalpy of formation of Li 2 [(UO 2 )(MoO 4 ) 2 ] was determined using HF solution calorimetry giving Δ f H°(T = 298 K, Li 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3456 ± 9) kJ · mol −1 . Using these new experimental results, together with literature data, the Gibbs free energy of formation of each compound was calculated, giving: Δ f G°(T = 298 K, Li 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3204 ± 9) kJ · mol −1 , Δ f G°(T = 298 K, Na 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3243 ± 2) kJ · mol −1 , Δ f G°(T = 298 K, K 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3269 ± 3) kJ · mol −1 , Δ f G°(T = 298 K, Rb 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3262 ± 3) kJ · mol −1 , and Δ f G°(T = 298 K, Cs 2 [(UO 2 )(MoO 4 ) 2 ], cr) = −(3259 ± 3) kJ · mol −1 . Smoothed S r °(T) values

High-pressure synthesis and crystal structure of α-Y{sub 2}B{sub 4}O{sub 9}

Energy Technology Data Exchange (ETDEWEB)

Schmitt, Martin K.; Huppertz, Hubert [Innsbruck Univ. (Austria). Inst. fuer Allgemeine, Anorganische und Theoretische Chemie

2017-07-01

α-Y{sub 2}B{sub 4}O{sub 9} was synthesized in a high-pressure/high-temperature experiment at 12.3 GPa/1020 C. The crystal structure has been determined via single-crystal X-ray diffraction. α-Y{sub 2}B{sub 4}O{sub 9} is isotypic to the lanthanide borates α-Ln{sub 2}B{sub 4}O{sub 9} (Ln = Sm-Ho) and crystallizes in the monoclinic space group C2/c (no. 15) with the following lattice parameters: a = 25.084(2), b = 4.3913(2), c = 24.726(2) Aa, and β = 99.97(1) . The compound was further characterized via X-ray powder diffraction as well as IR and Raman spectroscopy.

Full article: The Reaction between MoO3 and Molten K2S2O7 forming K2MoO2(SO4)2

DEFF Research Database (Denmark)

Nørbygaard, Thomas; Berg, Rolf W.; Nielsen, Kurt

1998-01-01

.4540(4), c = 8.8874(3) Å, beta = 112.194(1)o, wR2 = 0.0897 for 3491 independent reflections. The compound, K2MoO2(SO4)2, contains (Mo02)2+ core ions in distorted octahedral coordination, with two short (ca. 1.69 Å) terminal bonds in cis-configuration (the O-Mo-O angle is 103.1(2)o), and with two long (ca. 2...

Maternal protein intake in pregnancy and offspring metabolic health at age 9-16 y

DEFF Research Database (Denmark)

Maslova, Ekaterina; Hansen, Susanne; Grunnet, Louise Groth

2017-01-01

in free-living populations remains limited. Objective: We examined the association of protein intake in pregnancy with offspring metabolic health at age 9-16 y in a longitudinal cohort that oversampled pregnancies with gestational diabetes mellitus (GDM). Design: Six hundred eight women with an index...... provide little support for an association of maternal protein intake in pregnancy with measures of offspring metabolic health. Further studies in larger cohorts are needed to determine whether low maternal protein intake in pregnancy may improve glucose homeostasis in GDM-exposed and male offspring....... pregnancy affected by gestational diabetes mellitus and 626 controls enrolled in the Danish National Birth Cohort were used for the analysis. Protein (total, animal, vegetable) intake was assessed by using a foodfrequency questionnaire in gestational week 25. The offspring underwent a clinical examination...

Incorporation and conduction of proton in Sr-doped LaMO3 (M=Al, Sc, In, Yb, Y)

International Nuclear Information System (INIS)

Okuyama, Yuji; Kozai, Takeshi; Ikeda, Shohei; Matsuka, Maki; Sakai, Takaaki; Matsumoto, Hiroshige

2014-01-01

In order to clarify the effect of the B site species in ABO 3 perovskite oxides on the proton transport properties, the proton incorporation into a series of La 0.9 Sr 0.1 MO 3-δ , (M = Al, Sc, In, Yb, Y) was studied by measuring the electrical conductivity and electromotive forces of the gas concentration cells, and by a thermogravimetric analysis. The proton concentration and electrical conductivity increased in the order of the B site species, Al 0.9 Sr 0.1 AlO 3-δ showed an oxide ion conductivity, while La 0.9 Sr 0.1 YbO 3-δ and La 0.9 Sr 0.1 YO 3-δ exhibited a protonic conductivity in the temperature range of 573–1173 K. La 0.9 Sr 0.1 ScO 3-δ and La 0.9 Sr 0.1 InO 3-δ showed a protonic conductivity under 873 K, and a mixed proton and oxide ion conductivity at 1073 K

Single-layer MoS2 electronics.

Science.gov (United States)

Lembke, Dominik; Bertolazzi, Simone; Kis, Andras

2015-01-20

CONSPECTUS: Atomic crystals of two-dimensional materials consisting of single sheets extracted from layered materials are gaining increasing attention. The most well-known material from this group is graphene, a single layer of graphite that can be extracted from the bulk material or grown on a suitable substrate. Its discovery has given rise to intense research effort culminating in the 2010 Nobel Prize in physics awarded to Andre Geim and Konstantin Novoselov. Graphene however represents only the proverbial tip of the iceberg, and increasing attention of researchers is now turning towards the veritable zoo of so-called "other 2D materials". They have properties complementary to graphene, which in its pristine form lacks a bandgap: MoS2, for example, is a semiconductor, while NbSe2 is a superconductor. They could hold the key to important practical applications and new scientific discoveries in the two-dimensional limit. This family of materials has been studied since the 1960s, but most of the research focused on their tribological applications: MoS2 is best known today as a high-performance dry lubricant for ultrahigh-vacuum applications and in car engines. The realization that single layers of MoS2 and related materials could also be used in functional electronic devices where they could offer advantages compared with silicon or graphene created a renewed interest in these materials. MoS2 is currently gaining the most attention because the material is easily available in the form of a mineral, molybdenite, but other 2D transition metal dichalcogenide (TMD) semiconductors are expected to have qualitatively similar properties. In this Account, we describe recent progress in the area of single-layer MoS2-based devices for electronic circuits. We will start with MoS2 transistors, which showed for the first time that devices based on MoS2 and related TMDs could have electrical properties on the same level as other, more established semiconducting materials. This

Facile synthesis of stable structured MoS{sub 2}-Mo-CNFs heteroarchitecture with enhanced hydrogen evolution

Energy Technology Data Exchange (ETDEWEB)

Mo, Qionghua [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Faculty of Material and Energy, South West University, Chongqing 400700 (China); Yao, Yucen [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Liu, Bitao, E-mail: liubitao007@163.com [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Peng, Lingling; Yan, Hengqing; Hou, Zhupei; Wang, Jun [Research Institute for New Materials Technology, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Lin, Yue, E-mail: linyue@ustc.edu.cn [Hefei National Laboratory for Physical Sciences at the Microscale, University of Science and Technology of China, Anhui 230026 (China)

2017-06-01

3D structured MoS{sub 2} are grown in-situ on Mo particles embedded carbon nanofibers (CNFs) via a hydrothermal method. Due to this special structure, the bonding and effective electron delivery between CNFs and MoS{sub 2} are both enhanced, and which will exhibits a better hydrogen evolution activity. The onset potential of this MoS{sub 2}-Mo-CNFs catalyst will decreased to 60 mV compared to the 90 mV for the MoS{sub 2}-CNFs. And its current density nearly no change with 5000 cycles which is better than the 32.3% decrease of MoS{sub 2}-CNFs at η = 300 mV (V vs RHE). - Highlights: • Newly structured MoS{sub 2}-Mo-CNFs with effectively connection between MoS{sub 2} and CNFs successfully synthesized. • This structure can enhance the charge transfer and significantly increase electrocatalytic efficiency. • Nearly no HER activity loss after 5000 CV cycles.

Electrochemical H2O2 biosensor composed of myoglobin on MoS2 nanoparticle-graphene oxide hybrid structure.

Science.gov (United States)

Yoon, Jinho; Lee, Taek; Bapurao G, Bharate; Jo, Jinhee; Oh, Byung-Keun; Choi, Jeong-Woo

2017-07-15

In this research, the electrochemical biosensor composed of myoglobin (Mb) on molybdenum disulfide nanoparticles (MoS 2 NP) encapsulated with graphene oxide (GO) was fabricated for the detection of hydrogen peroxide (H 2 O 2 ). Hybrid structure composed of MoS 2 NP and GO (GO@MoS 2 ) was fabricated for the first time to enhance the electrochemical signal of the biosensor. As a sensing material, Mb was introduced to fabricate the biosensor for H 2 O 2 detection. Formation and immobilization of GO@MoS 2 was confirmed by transmission electron microscopy, ultraviolet-visible spectroscopy, scanning electron microscopy, and scanning tunneling microscopy. Immobilization of Mb, and electrochemical property of biosensor were investigated by cyclic voltammetry and amperometric i-t measurements. Fabricated biosensor showed the electrochemical signal enhanced redox current as -1.86μA at an oxidation potential and 1.95μA at a reduction potential that were enhanced relative to those of electrode prepared without GO@MoS 2 . Also, this biosensor showed the reproducibility of electrochemical signal, and retained the property until 9 days from fabrication. Upon addition of H 2 O 2 , the biosensor showed enhanced amperometric response current with selectivity relative to that of the biosensor prepared without GO@MoS 2 . This novel hybrid material-based biosensor can suggest a milestone in the development of a highly sensitive detecting platform for biosensor fabrication with highly sensitive detection of target molecules other than H 2 O 2 . Copyright © 2016 Elsevier B.V. All rights reserved.

Evaluation of pulsed laser annealing for flexible multilayer MoS2 transistors

International Nuclear Information System (INIS)

Kwon, Hyuk-Jun; Grigoropoulos, Costas P.; Kim, Sunkook; Jang, Jaewon

2015-01-01

To realize the proper electrical characteristics of field-effect transistors, the quality of the contact and interface must be improved because they can substantially distort the extracted mobility, especially for materials with low densities of states like molybdenum disulfide (MoS 2 ). We show that mechanically flexible MoS 2 thin-film transistors (TFTs) with selectively laser annealed source/drain electrodes achieve enhanced device performance without plastic deformation including higher field-effect mobility (from 19.59 to 45.91 cm 2  V −1  s −1 ) in the linear regime, decreased subthreshold swing, and enhanced current saturation. Furthermore, numerical thermal simulations, measured current-voltage characteristics, and contact-free mobility extracted from the Y-function method suggest that the enhanced performance originated from a decrease in the Schottky barrier effect at the contact and an improvement of the channel interface. These results demonstrate that picosecond laser annealing can be a promising technology for building high performance flexible MoS 2 TFTs in flexible/stretchable circuitry, which should be processed at low temperatures

Electron transfer kinetics on natural crystals of MoS2 and graphite.

Science.gov (United States)

Velický, Matěj; Bissett, Mark A; Toth, Peter S; Patten, Hollie V; Worrall, Stephen D; Rodgers, Andrew N J; Hill, Ernie W; Kinloch, Ian A; Novoselov, Konstantin S; Georgiou, Thanasis; Britnell, Liam; Dryfe, Robert A W

2015-07-21

Here, we evaluate the electrochemical performance of sparsely studied natural crystals of molybdenite and graphite, which have increasingly been used for fabrication of next generation monolayer molybdenum disulphide and graphene energy storage devices. Heterogeneous electron transfer kinetics of several redox mediators, including Fe(CN)6(3-/4-), Ru(NH3)6(3+/2+) and IrCl6(2-/3-) are determined using voltammetry in a micro-droplet cell. The kinetics on both materials are studied as a function of surface defectiveness, surface ageing, applied potential and illumination. We find that the basal planes of both natural MoS2 and graphite show significant electroactivity, but a large decrease in electron transfer kinetics is observed on atmosphere-aged surfaces in comparison to in situ freshly cleaved surfaces of both materials. This is attributed to surface oxidation and adsorption of airborne contaminants at the surface exposed to an ambient environment. In contrast to semimetallic graphite, the electrode kinetics on semiconducting MoS2 are strongly dependent on the surface illumination and applied potential. Furthermore, while visibly present defects/cracks do not significantly affect the response of graphite, the kinetics on MoS2 systematically accelerate with small increase in disorder. These findings have direct implications for use of MoS2 and graphene/graphite as electrode materials in electrochemistry-related applications.

Eu9Cd4-xCM2+x-y□ySb9: Ca9Mn4Bi9-type structure stuffed with coinage metals (Cu, Ag, and Au) and the challenges with classical valence theory in describing these possible zintl phases.

Science.gov (United States)

Kazem, Nasrin; Hurtado, Antonio; Klobes, Benedikt; Hermann, Raphaël P; Kauzlarich, Susan M

2015-02-02

The synthesis, crystal structure, magnetic properties, and europium Mössbauer spectroscopy of the new members of the 9-4-9 Zintl family of Eu(9)Cd(4-x)CM(2+x-y)□(y)Sb(9) (CM = coinage metal: Au, Ag, and Cu) are reported. These compounds crystallize in the Ca(9)Mn(4)Bi(9) structure type (9-4-9) with the 4g interstitial site almost half-occupied by coinage metals; these are the first members in the 9-4-9 family where the interstitial positions are occupied by a monovalent metal. All previously known compounds with this structure type include divalent interstitials where these interstitials are typically the same as the transition metals in the anionic framework. Single-crystal magnetic susceptibility data indicate paramagnetic behavior for all three compounds with antiferromagnetic ordering below 10 K (at 100 Oe) that shifts to lower temperature (x)CM(2+x-y)□(y)Sb(9) at 50 and 6.5 K in order to evaluate the valence of Eu cations. Although the Zintl formalism states that the five crystallographically distinct Eu sites in Eu(9)Cd(4-x)CM(2+x-y)□(y)Sb9 should bear Eu(2+), the Mössbauer spectral isomer shifts are clearly indicative of both 2+ and 3+ valence of the Eu cations with the Cu- and Au-containing compounds showing higher amounts of Eu(3+). This electronic configuration leads to an excess of negative charge in these compounds that contradicts the expected valence-precise requirement of Zintl phases. The spectra obtained at 6.5 K reveal magnetic ordering for both Eu(2+) and Eu(3+). The field dependence of Eu(2+) indicates two distinct magnetic sublattices, with higher and lower fields, and of a small field for Eu(3+). The site symmetry of the five Eu sites is not distinguishable from the Mössbauer data.

Some regularities in aging of solid oxide electrolytes ZrO2+Y2O3

International Nuclear Information System (INIS)

Vlasov, A.N.

1983-01-01

A study was made on the temperature effect on the rate and depth of aging of solid oxide electrolytes ZrO 2 +Y 2 O 3 and ZrO 2 +Ho 2 O 3 , stabilized by 10-15 mol.% R 2 O 3 following isothermal hold-up during 2000-3000 h in the 725-1550 deg C range in oxidizing medium. It was shown that solid electrolyte aging proceeds only at temperatures below a certain boundary value. The depth of complete aging at that increases with the R 2 O 3 concentration and a temperature decrease. The aging rate depends substantially on both temperature and concentration of a stabilizing addition. A decrease in the electric conductivity with time is accompanied by an increase in the conductivity activation energy

Low-frequency 1/f noise in MoS{sub 2} transistors: Relative contributions of the channel and contacts

Energy Technology Data Exchange (ETDEWEB)

Renteria, J.; Jiang, C. [Nano-Device Laboratory, Department of Electrical Engineering, Bourns College of Engineering, University of California – Riverside, Riverside, California 92521 (United States); Samnakay, R. [Materials Science and Engineering Program, Bourns College of Engineering, University of California – Riverside, Riverside, California 92521 (United States); Rumyantsev, S. L. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States); Ioffe Physical-Technical Institute, St. Petersburg 194021 (Russian Federation); Goli, P.; Balandin, A. A., E-mail: balandin@ee.ucr.edu [Nano-Device Laboratory, Department of Electrical Engineering, Bourns College of Engineering, University of California – Riverside, Riverside, California 92521 (United States); Materials Science and Engineering Program, Bourns College of Engineering, University of California – Riverside, Riverside, California 92521 (United States); Shur, M. S. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)

2014-04-14

We report on the results of the low-frequency (1/f, where f is frequency) noise measurements in MoS{sub 2} field-effect transistors revealing the relative contributions of the MoS{sub 2} channel and Ti/Au contacts to the overall noise level. The investigation of the 1/f noise was performed for both as fabricated and aged transistors. It was established that the McWhorter model of the carrier number fluctuations describes well the 1/f noise in MoS{sub 2} transistors, in contrast to what is observed in graphene devices. The trap densities extracted from the 1/f noise data for MoS{sub 2} transistors, are 2 × 10{sup 19} eV{sup −1}cm{sup −3} and 2.5 × 10{sup 20} eV{sup −1}cm{sup −3} for the as fabricated and aged devices, respectively. It was found that the increase in the noise level of the aged MoS{sub 2} transistors is due to the channel rather than the contact degradation. The obtained results are important for the proposed electronic applications of MoS{sub 2} and other van der Waals materials.

Cu4Pr6(MoO4)11-Pr2(MoO4)3 system

International Nuclear Information System (INIS)

Arzumanyan, G.A.

1982-01-01

Existence boundaries and Dalton compositions (CuPr(MoO 4 ) 2 , CuPr 3 (MoO 4 ) 5 ) of solid solutions that in the mojority are of shcheelite dsitored structure have been determined in the Cu 4 Pr 6 (MoO 4 ) 11 -Pr 2 (MoO 4 ) 3 system. It has been revealed that regions of homogeneity near the CuPr(MoO 4 ) 2 composition have a horseshoeshaped profile

Van der Waals epitaxial growth of MoS2 on SiO2/Si by chemical vapor deposition

KAUST Repository

Cheng, Yingchun

2013-01-01

Recently, single layer MoS2 with a direct band gap of 1.9 eV has been proposed as a candidate for two dimensional nanoelectronic devices. However, the synthetic approach to obtain high-quality MoS2 atomic thin layers is still problematic. Spectroscopic and microscopic results reveal that both single layers and tetrahedral clusters of MoS2 are deposited directly on the SiO2/Si substrate by chemical vapor deposition. The tetrahedral clusters are mixtures of 2H- and 3R-MoS2. By ex situ optical analysis, both the single layers and tetrahedral clusters can be attributed to van der Waals epitaxial growth. Due to the similar layered structures we expect the same growth mechanism for other transition-metal disulfides by chemical vapor deposition. © 2013 The Royal Society of Chemistry.

Electrochemical and metallurgical characterization of ZrCr{sub 1-x}NiMo{sub x} AB{sub 2} metal hydride alloys

Energy Technology Data Exchange (ETDEWEB)

Erika, Teliz [Universidad de la República, Facultad de Ciencias, Laboratorio de Electroquímica Fundamental, Núcleo Interdisciplinario Ingeniería Electroquímica, Igua 4225, CP 11400 Montevideo (Uruguay); Ricardo, Faccio [Universidad de la República, Crystallography, Solid State and Materials Laboratory (Cryssmat-Lab), DETEMA, Centro NanoMat, Polo Tecnológico de Pando, Espacio Interdisciplinario, Facultad de Química, Montevideo (Uruguay); Fabricio, Ruiz [Consejo Nacional de Investigaciones Científicas y Técnicas , CONICET, Av. Rivadavia 1917, C1033AAJ Ciudad de Buenos Aires (Argentina); Centro Atómico Bariloche , Comisión Nacional de Energía Atómica (CAB-CNEA), Av. Bustillo 9500, CP 8400 S.C. de Bariloche, RN (Argentina); Fernando, Zinola [Universidad de la República, Facultad de Ciencias, Laboratorio de Electroquímica Fundamental, Núcleo Interdisciplinario Ingeniería Electroquímica, Igua 4225, CP 11400 Montevideo (Uruguay); and others

2015-11-15

The effects of partial replacement of chromium by molybdenum was studied on the structure and electrochemical kinetic properties of ZrCr{sub 1-x}NiMo{sub x}(x = 0.0, 0.3 and 0.6) metal hydride alloys. The arc-melting prepared alloys were metallurgically characterized by X-ray diffraction and energy dispersive spectroscopy microanalysis, which showed AB{sub 2} (with hexagonal C14 structure) and Zr{sub x}Ni{sub y} (Zr{sub 7}Ni{sub 10}, Zr{sub 9}Ni{sub 11}) phases. After a partial substitution of chromium by molybdenum, secondary phases monotonically increase with the C14 unit cell volume indicating that most of molybdenum atoms locate in the B-site. The alloys were electrochemically characterized using charge/discharge cycling, electrochemical impedance spectroscopy and rate capability experiments that allowed the determination of hydriding reaction kinetic parameters. The presence of molybdenum produces a positive effect for hydrogen diffusion in the alloy lattice, and ZrCr{sub 0.7}NiMo{sub 0.3} alloy depicts the better kinetics associated with a fast activation, lower charge transfer resistance and the best high rate discharge behavior. This fact would be related to a lower diffusion time constant and a bigger value of the product between exchange density current and surface active area. There is a trade-off in the amounts of secondary phase and Laves phases in order to improve the kinetic performance. - Highlights: • Metallurgical characterization evidences the presence of Zr{sub x}Ni{sub y} and C14 phases. • The partial replacement of Cr by Mo promotes the segregation of Zr{sub x}Ni{sub y} phase. • The incorporation of molybdenum improves the kinetics for the hydriding process. • Mo produces a decrease in the diffusion time constant.

Excitation energy transfer to luminescence centers in M{sup II}MoO{sub 4} (M{sup II}=Ca, Sr, Zn, Pb) and Li{sub 2}MoO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Spassky, D.A., E-mail: deris2002@mail.ru [Skobeltsyn Institute of Nuclear Physics, M.V. Lomonosov Moscow State University, Leninskie Gory 1, bld.2, 119991 Moscow (Russian Federation); National University of Science and Technology (MISiS), Leninsky Prospekt 4, 119049 Moscow (Russian Federation); Kozlova, N.S. [National University of Science and Technology (MISiS), Leninsky Prospekt 4, 119049 Moscow (Russian Federation); Nagirnyi, V. [Institute of Physics, University of Tartu, W. Ostwaldi 1, 50411 Tartu (Estonia); Savon, A.E. [Skobeltsyn Institute of Nuclear Physics, M.V. Lomonosov Moscow State University, Leninskie Gory 1, bld.2, 119991 Moscow (Russian Federation); Hizhnyi, Yu.A.; Nedilko, S.G. [Taras Shevchenko National University of Kyiv, Volodymyrska str. 64/13, 01601 Kyiv (Ukraine)

2017-06-15

Based on the results of spectroscopy studies and electronic band structure calculations, the analysis of excitation energy transformation into luminescence is performed for a set of molybdates M{sup II}MoO{sub 4} (M{sup II}=Ca, Sr, Zn, Pb) and Li{sub 2}MoO{sub 4}. The bandgap energies were determined from comparison of experimental and calculated reflectivity spectra as 3.3 eV for PbMoO{sub 4}, 4.3 eV for ZnMoO{sub 4}, 4.4 eV for CaMoO{sub 4}, 4.7 eV for SrMoO{sub 4}, and 4.9 eV for Li{sub 2}MoO{sub 4}. It is shown that photoluminescence excitation spectra of these materials reveal the specific features of their conduction bands. The threshold of separated charge carriers’ creation is shown to be by 1.3–1.9 eV higher than the bandgap energy in CaMoO{sub 4}, SrMoO{sub 4} and ZnMoO{sub 4}. The effect is explained by the peculiarities of conduction band structure, namely to the presence of gap between the subbands of the conduction band and to the low mobility of electrons in the lower sub-band of the conduction band.

Retention mechanism of Mo in TiO{sub 2} and ZrO{sub 2}-TiO{sub 2}, potential adsorbents for the radionuclides separation; Mecanismo de retencion de Mo en TiO{sub 2} y ZrO{sub 2}-TiO{sub 2}, adsorbentes potenciales para la separacion de radionuclidos

Energy Technology Data Exchange (ETDEWEB)

Badillo A, V. E.; Perez H, R.; Lopez R, C.; Vidal M, J., E-mail: veronica.badillo@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2017-09-15

The retention properties of titanium and zirconium oxides are studied; solid adsorbents of high retention capacity for separation by chromatography of radionuclide pairs that are the basis of the so-called radionuclide generators. The titanium and zirconium nano materials obtained with a high retention capacity are prepared by the Sol-gel method using an alkoxide as a precursor. The acid-base properties are studied by potentiometric titrations, obtaining a value of the point of zero charge of 5.6 for TiO{sub 2} and 6.3 for the mixed oxide ZrO{sub 2}-TiO{sub 2}. To study the retention behavior of the {sup 99}Mo/{sup 99m}Tc radionuclide pair in these solids, batch experiments were performed on a 0.9% NaCl electrolyte as a function of the solution ph. The results show that {sup 99m}Tc is not absorbed by solids while {sup 99}Mo shows a high retention affinity for the metal oxides under study. The maximum adsorption of {sup 99}Mo takes place at a ph value close to the zero load point (pH{sub PZC}) (∼ 95% adsorption). This study focuses on the mechanism of molybdenum retention in terms of chemical equilibria between the functional groups of the solid (OH-) and the species of Mo(Vi) in solution. The experimental data of molybdenum retention were analyzed with the FITEQL program using the constant capacitance model and assuming the presence of a single type of sites on the surface of the solids (hydroxyl groups). In Mo(Vi) retention, surface complexes that are formed through a ligand exchange mechanism between molybdate species and hydroxyl ions from the surface of the solid are probably the mechanism responsible for adsorption in the ph range that is studied. (Author)

On-stack two-dimensional conversion of MoS2 into MoO3

Science.gov (United States)

Yeoung Ko, Taeg; Jeong, Areum; Kim, Wontaek; Lee, Jinhwan; Kim, Youngchan; Lee, Jung Eun; Ryu, Gyeong Hee; Park, Kwanghee; Kim, Dogyeong; Lee, Zonghoon; Lee, Min Hyung; Lee, Changgu; Ryu, Sunmin

2017-03-01

Chemical transformation of existing two-dimensional (2D) materials can be crucial in further expanding the 2D crystal palette required to realize various functional heterostructures. In this work, we demonstrate a 2D ‘on-stack’ chemical conversion of single-layer crystalline MoS2 into MoO3 with a precise layer control that enables truly 2D MoO3 and MoO3/MoS2 heterostructures. To minimize perturbation of the 2D morphology, a nonthermal oxidation using O2 plasma was employed. The early stage of the reaction was characterized by a defect-induced Raman peak, drastic quenching of photoluminescence (PL) signals and sub-nm protrusions in atomic force microscopy images. As the reaction proceeded from the uppermost layer to the buried layers, PL and optical second harmonic generation signals showed characteristic modulations revealing a layer-by-layer conversion. The plasma-generated 2D oxides, confirmed as MoO3 by x-ray photoelectron spectroscopy, were found to be amorphous but extremely flat with a surface roughness of 0.18 nm, comparable to that of 1L MoS2. The rate of oxidation quantified by Raman spectroscopy decreased very rapidly for buried sulfide layers due to protection by the surface 2D oxides, exhibiting a pseudo-self-limiting behavior. As exemplified in this work, various on-stack chemical transformations can be applied to other 2D materials in forming otherwise unobtainable materials and complex heterostructures, thus expanding the palette of 2D material building blocks.

Risk factors for severe acute malnutrition in children below 5 y of age in India: a case-control study.

Science.gov (United States)

Mishra, Kirtisudha; Kumar, Praveen; Basu, Srikanta; Rai, Kiran; Aneja, Satinder

2014-08-01

To determine the possible risk factors for severe acute malnutrition (SAM) in children below 5 y admitted in a hospital in north India. This case-control study was conducted in a medical college hospital in children below 5 y of age. All cases of SAM (diagnosed as per WHO definition) between 6 and 59 mo of age were compared with age-matched controls with weight for height above -2SD of WHO 2006 growth standards. Data regarding socio-demographic parameters, feeding practices and immunization were compared between the groups by univariable and multivariable logistic regression models. A total of 76 cases and 115 controls were enrolled. Among the 14 factors compared, maternal illiteracy, daily family income less than Rs. 200, large family size, lack of exclusive breast feeding in first 6 mo, bottle feeding, administration of pre-lacteals, deprivation of colostrum and incomplete immunization were significant risk factors for SAM. Regarding complementary feeding, it was the consistency, rather than the age of initiation, frequency and variety which showed a significant influence on occurrence of SAM. Multivariate analysis revealed that the risk of SAM was independently associated with 6 factors, namely, illiteracy among mothers, incomplete immunization, practice of bottle feeding, consistency of complementary feeding, deprivation of colostrum and receipt of pre-lacteals at birth. The present study identifies certain risk factors which need to be focused on during health planning and policy making related to children with SAM in India.

P-MoS2 / n-CdS thin film heterojunction

International Nuclear Information System (INIS)

El Maliki, H.; Gourmelon, E.; Bernede, J.C.; Pouzet, J.; Mebarki, M.; Khelil, A.; Zoaeter, M.

1999-01-01

Full text.Layered transition metal dichacolgenides such as MoS 2 are semiconductors that can be good candidates for solar energy conversion. Photo-electrochemical cells based on single crystals have achieved and efficiency of 17% (1). However, up to day, no solid rectifying contact has been put in evidence in the case of MoS 2 thin films.. Recently we have shown that such high crystalline quality MoS 2 films can be obtained onto textured tungsten slides. This allowed to try to grow sandwich rectifying structures. The bottom electrode will be W, MoS 2 being p-type, the n type film used was CdS and the upper electrode was indium. W foils textured along the (h00) direction were used as substrate and bottom electrode. The use of a W (textured) substrate induces the texturation of the MoS 2 films along the (001) direction when after evaporation of the constituents the films were annealed at T=1073 K for half an hour under argon atmosphere. Upon the MoS 2 a CdS thin film was deposited by chemical bath deposition (CBD). CdS thin films were prepared classically from a solution of cadmium sulfate, thiourea in hydrazine and ammonia. Ammonia was used adjust the solution pH to a value between 9 and 10. Bath temperature has been held constant at 343 K. Thin deposit films of CdS were yellow colored. They were constituted of an homogenous and adherent layer with a thickness of about 100 nm. It has been shown by x-ray diffraction the they were crystallized in their hexagonal structure. At least an indium film was deposited in order to achieve the structure M/MoS 2 p/CdSn/M. In order to check the equality of the W/MoS 2 contact, W/MoS 2 /W samples were also carried out by sputtering deposition of the tungsten upper electrode (300 nm thick). The thickness of the MoS 2 layers was about 500 nm. The J-V characteristics of a W/MoS 2 /W sample are ohmic. Moreover the resistance deduced from the slope ΔV/ΔI increases when the temperature decreases, which shows that there is not any

Study of the dynamics of the MoO2-Mo2C system for catalytic partial oxidation reactions

Science.gov (United States)

Cuba Torres, Christian Martin

On a global scale, the energy demand is largely supplied by the combustion of non-renewable fossil fuels. However, their rapid depletion coupled with environmental and sustainability concerns are the main drivers to seek for alternative energetic strategies. To this end, the sustainable generation of hydrogen from renewable resources such as biodiesel would represent an attractive alternative solution to fossil fuels. Furthermore, hydrogen's lower environmental impact and greater independence from foreign control make it a strong contender for solving this global problem. Among a wide variety of methods for hydrogen production, the catalytic partial oxidation offers numerous advantages for compact and mobile fuel processing systems. For this reaction, the present work explores the versatility of the Mo--O--C catalytic system under different synthesis methods and reforming conditions using methyl oleate as a surrogate biodiesel. MoO2 exhibits good catalytic activity and exhibits high coke-resistance even under reforming conditions where long-chain oxygenated compounds are prone to form coke. Moreover, the lattice oxygen present in MoO2 promotes the Mars-Van Krevelen mechanism. Also, it is introduced a novel beta-Mo2C synthesis by the in-situ formation method that does not utilize external H2 inputs. Herein, the MoO 2/Mo2C system maintains high catalytic activity for partial oxidation while the lattice oxygen serves as a carbon buffer for preventing coke formation. This unique feature allows for longer operation reforming times despite slightly lower catalytic activity compared to the catalysts prepared by the traditional temperature-programmed reaction method. Moreover, it is demonstrated by a pulse reaction technique that during the phase transformation of MoO2 to beta-Mo2C, the formation of Mo metal as an intermediate is not responsible for the sintering of the material wrongly assumed by the temperature-programmed method.

Few-layered MoSe2 nanosheets as an advanced electrode material for supercapacitors.

Science.gov (United States)

Balasingam, Suresh Kannan; Lee, Jae Sung; Jun, Yongseok

2015-09-21

We report the synthesis of few-layered MoSe2 nanosheets using a facile hydrothermal method and their electrochemical charge storage behavior. A systematic study of the structure and morphology of the as-synthesized MoSe2 nanosheets was performed. The downward peak shift in the Raman spectrum and the high-resolution transmission electron microscopy images confirmed the formation of few-layered nanosheets. The electrochemical energy-storage behavior of MoSe2 nanosheets was also investigated for supercapacitor applications in a symmetric cell configuration. The MoSe2 nanosheet electrode exhibited a maximum specific capacitance of 198.9 F g(-1) and the symmetric device showed 49.7 F g(-1) at a scan rate of 2 mV s(-1). A capacitance retention of approximately 75% was observed even after 10 000 cycles at a high charge-discharge current density of 5 A g(-1). The two-dimensional MoSe2 nanosheets exhibited a high specific capacitance and good cyclic stability, which makes it a promising electrode material for supercapacitor applications.

Shape coexistence in the odd-odd nucleus ${}^{98}{<span\; class="hlt">Y</span>}$ : The role of the mo>/>2 neutron extruder

Energy Technology Data Exchange (ETDEWEB)

Urban, W.; Czerwiński, M.; Kurpeta, J.; Rząca-Urban, T.; Wiśniewski, J.; Materna, T.; Iskra, Ł. W.; Smith, A. G.; Ahmad, I.; Blanc, A.; Faust, H.; Köster, U.; Jentschel, M.; Mutti, P.; Soldner, T.; Simpson, G. S.; Pinston, J. A.; de France, G.; Ur, C. A.; Elomaa, V. -V.; Eronen, T.; Hakala, J.; Jokinen, A.; Kankainen, A.; Moore, I. D.; Rissanen, J.; Saastamoinen, A.; Szerypo, J.; Weber, C.; Äystö, J.

2017-10-01

Excited states in Y-98, populated in neutron-induced fission of U-235 and in spontaneous fission of Cm-248 and Cf-252, have been studied by means of gamma spectroscopy using the Lohengrin fission-fragment separator at ILL Grenoble and the EXILL, Eurogam2, and Gammasphere Ge arrays. Two new isomers have been found in Y-98: a deformed one with T-1/2 = 180(7) ns and a rotational band on top of it, and a spherical one with T-1/2 = 0.45(15) mu s, analogous to the 8(+) isomer in Y-96, corresponding to the (nu g(7/2), pi g(9/2))(8+) spherical configuration. Using the JYFLTRAP Penning trap, an accurate excitation energy of 465.7(7) keV has been determined for the 2.36-s isomer in Y-98. This result and the studies of excited levels in Zr-98, populated in beta-decay of the isomer, indicate a new spin-parity, I-pi = (7)(+) for the isomer. The high spin and the decay properties of this isomer suggest the presence of the 9/2(+)[ 404] neutron extruder orbital in its structure. This is consistent with the large deformation of the isomer, reported recently. The present work does not provide arguments to support the special role of the nu g(7/2)-pi g(9/2) interaction (the spin-orbit-partner, or SOP, mechanism).