WorldWideScience

Sample records for advanced oxidation processes

  1. AN ADVANCED OXIDATION PROCESS : FENTON PROCESS

    Directory of Open Access Journals (Sweden)

    Engin GÜRTEKİN

    2008-03-01

    Full Text Available Biological wastewater treatment is not effective treatment method if raw wastewater contains toxic and refractory organics. Advanced oxidation processes are applied before or after biological treatment for the detoxification and reclamation of this kind of wastewaters. The advanced oxidation processes are based on the formation of powerful hydroxyl radicals. Among advanced oxidation processes Fenton process is one of the most promising methods. Because application of Fenton process is simple and cost effective and also reaction occurs in a short time period. Fenton process is applied for many different proposes. In this study, Fenton process was evaluated as an advanced oxidation process in wastewater treatment.

  2. AN ADVANCED OXIDATION PROCESS : FENTON PROCESS

    OpenAIRE

    Engin GÜRTEKİN; Nusret ŞEKERDAĞ

    2008-01-01

    Biological wastewater treatment is not effective treatment method if raw wastewater contains toxic and refractory organics. Advanced oxidation processes are applied before or after biological treatment for the detoxification and reclamation of this kind of wastewaters. The advanced oxidation processes are based on the formation of powerful hydroxyl radicals. Among advanced oxidation processes Fenton process is one of the most promising methods. Because application of Fenton process is simple ...

  3. Advanced oxidation processes: overall models

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, M. [Univ. de los Andes, Escuela Basica de Ingenieria, La Hechicera, Merida (Venezuela); Curco, D.; Addardak, A.; Gimenez, J.; Esplugas, S. [Dept. de Ingenieria Quimica. Univ. de Barcelona, Barcelona (Spain)

    2003-07-01

    Modelling AOPs implies to consider all the steps included in the process, that means, mass transfer, kinetic (reaction) and luminic steps. In this way, recent works develop models which relate the global reaction rate to catalyst concentration and radiation absorption. However, the application of such models requires to know what is the controlling step for the overall process. In this paper, a simple method is explained which allows to determine the controlling step. Thus, it is assumed that reactor is divided in two hypothetical zones (dark and illuminated), and according to the experimental results, obtained by varying only the reaction volume, it can be decided if reaction occurs only in the illuminated zone or in the all reactor, including dark zone. The photocatalytic degradation of phenol, by using titania degussa P-25 as catalyst, is studied as reaction model. The preliminary results obtained are presented here, showing that it seems that, in this case, reaction only occurs in the illuminated zone of photoreactor. A model is developed to explain this behaviour. (orig.)

  4. HANDBOOK ON ADVANCED NONPHOTOCHEMICAL OXIDATION PROCESSES

    Science.gov (United States)

    The purpose of this handbook is to summarize commercial-scale system performance and cost data for advanced nonphotochemical oxidation (ANPO) treatment of contaminated water, air, and soil. Similar information from pilot-and bench-scale evaluations of ANPO processes is also inclu...

  5. HANDBOOK ON ADVANCED PHOTOCHEMICAL OXIDATION PROCESSES

    Science.gov (United States)

    This handbook summarizes commercial-scale system performance and cost data for advanced photochemical oxidation (APO) treatment of contaminated water, air, and solids. Similar information from pilot- and bench-scale evaluations of APO processes is also included to supplement the...

  6. Micropollutant removal by advanced oxidation processes

    OpenAIRE

    Autin, Olivier

    2012-01-01

    The use of pesticides in agriculture has been associated to high concentrations found in surface waters and ultimately to the tightening of drinking water regulations. Whilst traditional granular activated carbon filtration or ozone are effective barriers for the large majority of pesticides, new polar pesticides such as clopyralid or metaldehyde are not readily removed by such technologies. The use of advanced oxidation processes (AOPs) is suggested as an effective alternative...

  7. Advanced oxidation process sanitization of eggshell surfaces.

    Science.gov (United States)

    Gottselig, Steven M; Dunn-Horrocks, Sadie L; Woodring, Kristy S; Coufal, Craig D; Duong, Tri

    2016-06-01

    The microbial quality of eggs entering the hatchery represents an important critical control point for biosecurity and pathogen reduction programs in integrated poultry production. The development of safe and effective interventions to reduce microbial contamination on the surface of eggs will be important to improve the overall productivity and microbial food safety of poultry and poultry products. The hydrogen peroxide (H2O2) and ultraviolet (UV) light advanced oxidation process is a potentially important alternative to traditional sanitizers and disinfectants for egg sanitation. The H2O2/UV advanced oxidation process was demonstrated previously to be effective in reducing surface microbial contamination on eggs. In this study, we evaluated treatment conditions affecting the efficacy of H2O2/UV advanced oxidation in order to identify operational parameters for the practical application of this technology in egg sanitation. The effect of the number of application cycles, UV intensity, duration of UV exposure, and egg rotation on the recovery of total aerobic bacteria from the surface of eggs was evaluated. Of the conditions evaluated, we determined that reduction of total aerobic bacteria from naturally contaminated eggs was optimized when eggs were sanitized using 2 repeated application cycles with 5 s exposure to 14 mW cm(-2) UV light, and that rotation of the eggs between application cycles was unnecessary. Additionally, using these optimized conditions, the H2O2/UV process reduced Salmonella by greater than 5 log10 cfu egg(-1) on the surface of experimentally contaminated eggs. This study demonstrates the potential for practical application of the H2O2/UV advanced oxidation process in egg sanitation and its effectiveness in reducing Salmonella on eggshell surfaces. PMID:27030693

  8. Induced effects of advanced oxidation processes

    Science.gov (United States)

    Liu, Peng; Li, Chaolin; Zhao, Zhuanjun; Lu, Gang; Cui, Haibo; Zhang, Wenfang

    2014-02-01

    Hazardous organic wastes from industrial, military, and commercial activities represent one of the greatest challenges to human beings. Advanced oxidation processes (AOPs) are alternatives to the degradation of those organic wastes. However, the knowledge about the exact mechanisms of AOPs is still incomplete. Here we report a phenomenon in the AOPs: induced effects, which is a common property of combustion reaction. Through analysis EDTA oxidation processes by Fenton and UV-Fenton system, the results indicate that, just like combustion, AOPs are typical induction reactions. One most compelling example is that pre-feeding easily oxidizable organic matter can promote the oxidation of refractory organic compound when it was treated by AOPs. Connecting AOPs to combustion, it is possible to achieve some helpful enlightenment from combustion to analyze, predict and understand AOPs. In addition, we assume that maybe other oxidation reactions also have induced effects, such as corrosion, aging and passivation. Muchmore research is necessary to reveal the possibilities of induced effects in those fields.

  9. Proceedings of the second international conference on advanced oxidation processes

    International Nuclear Information System (INIS)

    The major objective of the conference is to discuss the recent developments in diversified fields in advanced oxidation processes. Development of new and modern technologies for water purification is vital to water management in any country. Advanced oxidation process is among the latest methodologies which are under tremendous researches in the recent past. In-situ generation of highly oxidizing species using chemical, photochemical, sonochemical and radiation chemical techniques were the focus of the discussions. Papers relevant to INIS are indexed separately

  10. ADVANCED OXIDATION PROCESSES FOR FOOD INDUSTRIAL WASTEWATER DECONTAMINATION

    OpenAIRE

    Dorota Krzemińska; Ewa Neczaj; Gabriel Borowski

    2015-01-01

    High organic matter content is a basic problem in food industry wastewaters. Typically, the amount and composition of the effluent varies considerably. In the article four groups of advanced processes and their combination of food industry wastewater treatment have been reviewed: electrochemical oxidation (EC), Fenton’s process, ozonation of water and photocatalytic processes. All advanced oxidation processes (AOP`s) are characterized by a common chemical feature: the capability of exploiting...

  11. ADVANCED OXIDATION PROCESSES FOR FOOD INDUSTRIAL WASTEWATER DECONTAMINATION

    Directory of Open Access Journals (Sweden)

    Dorota Krzemińska

    2015-02-01

    Full Text Available High organic matter content is a basic problem in food industry wastewaters. Typically, the amount and composition of the effluent varies considerably. In the article four groups of advanced processes and their combination of food industry wastewater treatment have been reviewed: electrochemical oxidation (EC, Fenton’s process, ozonation of water and photocatalytic processes. All advanced oxidation processes (AOP`s are characterized by a common chemical feature: the capability of exploiting high reactivity of HO• radicals in driving oxidation processes which are suitable for achieving decolonization and odour reduction, and the complete mineralization or increase of bioavailability of recalcitrant organic pollutants.

  12. ADVANCED OXIDATION PROCESSES (AOP'S FOR THE TREATMENT OF CCL CHEMICALS

    Science.gov (United States)

    Research on treatment of Contaminant Candidate List (CCL) chemicals is being conducted. Specific groups of contaminants on the CCL will be evaluated using numerous advanced oxidation processes (AOPs). Initially, these CCL contaminants will be evaluated in groups based on chemical...

  13. Treatment of Landfill Leachate by Advanced Oxidation Processes

    OpenAIRE

    Koçak, Seda; Güney, Cansu; Argun, M. Tuna; Tarkın, Begüm; Kırtman, E. Özlem; Akgül, Deniz; MERTOGLU, Bulent

    2013-01-01

    Organic and inorganic pollutants found in municipal landfill leachate lead to severe problems for the environment when directly discharged to water bodies without treatment. Due to the existence of recalcitrant organics in leachate, advanced oxidation processes (AOP) are mostly applied to biologically treated leachate as a polishing step. In this study, the effectiveness of Fenton process on leachate treatment was examined. The Fenton process was applied to both young (untreated) and biologic...

  14. Degradation of 2-hydroxybenzoic acid by advanced oxidation processes

    OpenAIRE

    C. L. P. S. Zanta; Martínez-Huitle, C. A.

    2009-01-01

    In this study, advanced oxidation processes (AOPs) such as the UV/H2O2 and Fenton processes were investigated for the degradation of 2-hydroxybenzoic acid (2-HBA) in lab-scale experiments. Different [H2O2]/[2-HBA] molar ratios and pH values were used in order to establish the most favorable experimental conditions for the Fenton process. For comparison purposes, degradation of 2-HBA was carried out by the UV/H2O2 process under Fenton experimental conditions. The study showed that the Fenton p...

  15. Advanced oxidation processes for wastewater reuse - removal of micropollutants

    OpenAIRE

    James, Christopher P.

    2013-01-01

    The removal of micropollutants (MPs) from secondary municipal wastewater by an advanced oxidation process (AOP) based on UV irradiation combined with hydrogen peroxide (UV/H2O2) has been assessed through pilot-scale experiments incorporating microfiltration (MF) and reverse osmosis (RO). Tests employed low concentrations of a range of emerging contaminants of concern, and the water quality varied by blending of waters from different sources. Under optimum H2O2 and lamp power...

  16. Use of advanced oxidation processes for removal of micropollutants

    DEFF Research Database (Denmark)

    Madsen, Henrik Tækker; Søgaard, Erik Gydesen

    One of the big challenges of modern water treatment is the handling of micropollutants. These are compounds found in very low concentrations, often at ppt or ppb level, but are still capable of having a potent effect on the environment, and possibly humans as well. One of the emerging technologies...... for removal of micropollutants is the use of advanced oxidation processes (AOPs). AOPs use highly reactive hydroxyl radicals to degrade the micropollutants, but the processes are very energy intensive, which may limit their applications. To investigate the feasibility of introducing AOPs in the Danish...

  17. Modular Advanced Oxidation Process Enabled by Cathodic Hydrogen Peroxide Production

    OpenAIRE

    Barazesh, JM; Hennebel, T; Jasper, JT; Sedlak, DL

    2015-01-01

    Hydrogen peroxide (H2O2) is frequently used in combination with ultraviolet (UV) light to treat trace organic contaminants in advanced oxidation processes (AOPs). In small-scale applications, such as wellhead and point-of-entry water treatment systems, the need to maintain a stock solution of concentrated H2O2 increases the operational cost and complicates the operation of AOPs. To avoid the need for replenishing a stock solution of H2O2, a gas diffusion electrode was used to generate low con...

  18. Advanced treatment of pharmaceutical wastewater by Fenton reagent oxidation process

    Directory of Open Access Journals (Sweden)

    Yanan YANG

    2015-12-01

    Full Text Available Avermectin-salinomycin waster is hard to be further biodegraded after treated by anaerobic-aerobiotic process, so Fenton oxidation process is studied for its advanced treatment. Influencing factors of pH, reaction time, H2O2 dosage and H2O2/Fe2+ on COD removal are investigated, respectively. When pH value is 3.0, the dosage of H2O2 is 1.5 mL/L, and the mole ratio of H2O2/Fe2+ is 5∶1, the effluent COD mass concentrations decreases from 224 to 64.3 mg/L, namely the COD removal efficiency reaches 71.3%.

  19. ELECTROCHEMICAL ADVANCED OXIDATION PROCESS UTILIZING NB-DOPED TIO2 ELECTRODES

    Science.gov (United States)

    An electrochemical advanced oxidation process has been developed utilizing electrodes which generate hydroxyl free radical (HO) by oxidizing water. All substrates tested are oxidized, mostly with reaction rates proportional to the corresponding rate constants for reaction with hy...

  20. Application of advanced oxidative process in treatment radioactive waste

    International Nuclear Information System (INIS)

    The ion exchange resin is used in the water purification system in both nuclear research and power reactors. Combined with active carbon, the resin removes dissolved elements from water when the nuclear reactor is operating. After its consumption, it becomes a special type of radioactive waste. The usual treatment to this type of waste is the immobilization with Portland cement, which is simple and low cost. However, its low capacity of immobilization and the increase volume of waste have been the challenges. The development of new technologies capable of destroying this waste completely by increasing its solidification is the main target due to the possibility of both volume and cost reduction. The objective of this work was to evaluate ion exchange resin degradation by Advanced Oxidative Process using Fenton's Reagent (H2O2 / Fe+2) in different concentration and temperatures. One advantage of this process is that all additional organic compounds or inorganic solids produced are oxidized easily. The degradation experiments were conducted with IRA-400 resin and Fenton's Reagents, varying the H2O2 concentration (30% e 50%) and heat temperature (25, 60 and 100 deg C). The resin degradation was confirmed by the presence of BaCO3 as a white precipitate resulting from the reaction between the Ba(OH)2 and the CO2 from the resin degradation. All experiments run in duplicate. Higher degradation was observed with Fenton's Reagent (Fe+2 /H2O2 30%) at 100 deg C after 2 hours. (author)

  1. Applications of advanced oxidation processes: present and future.

    Science.gov (United States)

    Suty, H; De Traversay, C; Cost, M

    2004-01-01

    The use of advanced oxidation processes (AOPs) to remove pollutants in various water treatment applications has been the subject of study for around 30 years. Most of the available processes (Fenton reagent, O3 under basic conditions, O3/H2O2, O3/UV, O3/solid catalyst, H2O2/M(n+), H2O2/UV, photo-assisted Fenton, H2O2/solid catalyst, H2O2/NaClO, TiO2/UV etc.) have been investigated in depth and a considerable body of knowledge has been built up about the reactivity of many pollutants. Various industrial applications have been developed, including ones for ground remediation (TCE, PCE), the removal of pesticides from drinking water, the removal of formaldehyde and phenol from industrial waste water and a reduction in COD from industrial waste water. The development of such AOP applications has been stimulated by increasingly stringent regulations, the pollution of water resources through agricultural and industrial activities and the requirement that industry meet effluent discharge standards. Nevertheless, it is difficult to obtain an accurate picture of the use of AOPs and its exact position in the range of water treatment processes has not been determined to date. The purpose of this overview is to discuss those processes and provide an indication of future trends. PMID:15077976

  2. Application of Advanced Oxidation Processes to Wastewater Treatment

    OpenAIRE

    Lucas, Marco Paulo Gomes de Sousa

    2009-01-01

    Tese de Doutoramento em Química This research contributes to the study and development of advanced oxidation technologies applied to two different problematic wastewaters: textile and winery wastewaters. In this dissertation the factors that influence the oxidation of the model compound of textile wastewaters, the azo dye Reactive Black 5 (RB5), and of the winery wastewaters were investigated. The first part of the thesis experimental work is dedicated to the decolorization of RB5 solut...

  3. Pengolahan Limbah Cair Pabrik Pupuk Urea Menggunakan Advanced Oxidation Processes

    Directory of Open Access Journals (Sweden)

    Darmadi Darmadi

    2014-06-01

    Full Text Available Limbah cair pabrik pupuk urea terdiri dari urea dan amonium yang masing-masing mempunyai konsentrasi berkisar antara 1500-10000 ppm dan 400-3000 ppm. Konsentrasi urea yang tinggi di dalam badan air dapat menyebabkan blooming algae dalam ekosistem tersebut yang dapat mengakibatkan kehidupan biota air lain terserang penyakit. Peristiwa ini terjadi karena kurangnya nutrisi bagi biota air dan sedikitnya sinar matahari yang dapat menembusi permukaan air. Disamping kedua hal tersebut di atas, algae juga dapat memproduksi senyawa beracun bagi biota air dan manusia. Penelitian ini bertujuan untuk mengolah urea menggunakan oksidasi konvensional (H2O2 dan Advanced Oxidation Processes (kombinasi H2O2-Fe2+ pada pH 5 dengan parameter yang digunakan adalah variasi konsen-trasi awal H2O2  dan konsentrasi Fe2+. Hasil percobaan menunjukkan bahwa penurunan konsentrasi urea tertinggi diperoleh pada penggunaan reagen fenton (8000 ppm H2O2 dan 500 ppm Fe2+, yaitu dapat menurunkan urea dari konsentrasi awal urea 2566,145 ppm menjadi 0 ppm. Kinetika reaksi dekomposisi urea menjadi amonium dan amonium menjadi nitrit dan nitrat yang diuji mengikuti laju kinetika reaksi orde 1 (satu terhadap urea dan orde satu terhadap amonium dengan konstanta laju reaksi masing-masing k1 = 0,019 dan k2 = 0,022 min-1.

  4. Modular advanced oxidation process enabled by cathodic hydrogen peroxide production.

    Science.gov (United States)

    Barazesh, James M; Hennebel, Tom; Jasper, Justin T; Sedlak, David L

    2015-06-16

    Hydrogen peroxide (H2O2) is frequently used in combination with ultraviolet (UV) light to treat trace organic contaminants in advanced oxidation processes (AOPs). In small-scale applications, such as wellhead and point-of-entry water treatment systems, the need to maintain a stock solution of concentrated H2O2 increases the operational cost and complicates the operation of AOPs. To avoid the need for replenishing a stock solution of H2O2, a gas diffusion electrode was used to generate low concentrations of H2O2 directly in the water prior to its exposure to UV light. Following the AOP, the solution was passed through an anodic chamber to lower the solution pH and remove the residual H2O2. The effectiveness of the technology was evaluated using a suite of trace contaminants that spanned a range of reactivity with UV light and hydroxyl radical (HO(•)) in three different types of source waters (i.e., simulated groundwater, simulated surface water, and municipal wastewater effluent) as well as a sodium chloride solution. Irrespective of the source water, the system produced enough H2O2 to treat up to 120 L water d(-1). The extent of transformation of trace organic contaminants was affected by the current density and the concentrations of HO(•) scavengers in the source water. The electrical energy per order (EEO) ranged from 1 to 3 kWh m(-3), with the UV lamp accounting for most of the energy consumption. The gas diffusion electrode exhibited high efficiency for H2O2 production over extended periods and did not show a diminution in performance in any of the matrices. PMID:26039560

  5. Anodic oxidation with doped diamond electrodes: a new advanced oxidation process

    International Nuclear Information System (INIS)

    Boron-doped diamond anodes allow to directly produce OH· radicals from water electrolysis with very high current efficiencies. This has been explained by the very high overvoltage for oxygen production and many other anodic electrode processes on diamond anodes. Additionally, the boron-doped diamond electrodes exhibit a high mechanical and chemical stability. Anodic oxidation with diamond anodes is a new advanced oxidation process (AOP) with many advantages compared to other known chemical and photochemical AOPs. The present work reports on the use of diamond anodes for the chemical oxygen demand (COD) removal from several industrial wastewaters and from two synthetic wastewaters with malic acid and ethylenediaminetetraacetic (EDTA) acid. Current efficiencies for the COD removal between 85 and 100% have been found. The formation and subsequent removal of by-products of the COD oxidation has been investigated for the first time. Economical considerations of this new AOP are included

  6. Petroleum Refinery Effluents Treatment by Advanced Oxidation Process with Methanol

    Energy Technology Data Exchange (ETDEWEB)

    Shoucheng, Wen [Yangtze Univ., HuBei Jingzhou (China)

    2014-02-15

    Petroleum refinery effluents are waste originating from industries primarily engaged in refining crude oil. It is a very complex compound of various oily wastes, water, heavy metals and so on. Conventional processes are unable to effectively remove the chemical oxygen demand (COD) of petroleum refinery effluents. Supercritical water oxidation (SCWO) was proposed to treat petroleum refinery effluents. In this paper, methanol was used to investigate co-oxidative effect of methanol on petroleum refinery effluents treatment. The results indicated that supercritical water oxidation is an effective process for petroleum refinery effluents treatment. Adding methanol caused an increase in COD removal. When reaction temperature is 440 .deg. C, residence time is 20 min, OE is 0.5 and initial COD is 40000 mg/L, and COD removal increases 8.5%.

  7. Petroleum Refinery Effluents Treatment by Advanced Oxidation Process with Methanol

    International Nuclear Information System (INIS)

    Petroleum refinery effluents are waste originating from industries primarily engaged in refining crude oil. It is a very complex compound of various oily wastes, water, heavy metals and so on. Conventional processes are unable to effectively remove the chemical oxygen demand (COD) of petroleum refinery effluents. Supercritical water oxidation (SCWO) was proposed to treat petroleum refinery effluents. In this paper, methanol was used to investigate co-oxidative effect of methanol on petroleum refinery effluents treatment. The results indicated that supercritical water oxidation is an effective process for petroleum refinery effluents treatment. Adding methanol caused an increase in COD removal. When reaction temperature is 440 .deg. C, residence time is 20 min, OE is 0.5 and initial COD is 40000 mg/L, and COD removal increases 8.5%

  8. Evaluation of Resin Dissolution Using an Advanced Oxidation Process - 13241

    Energy Technology Data Exchange (ETDEWEB)

    Goulart de Araujo, Leandro; Vicente de Padua Ferreira, Rafael; Takehiro Marumo, Julio [Nuclear and Energy Research Institute, Av. Lineu Prestes, 2242., Sao Paulo, SP. (Brazil); Passos Piveli, Roque; Campos, Fabio [The Polytechnic School of the University of Sao Paulo, Av. Prof. Almeida Prado, 83, trav.2. Sao Paulo, SP (Brazil)

    2013-07-01

    The ion-exchange resin is widely used in nuclear reactors, in cooling water purification and removing radioactive elements. Because of the long periods of time inside the reactor system, the resin becomes radioactive. When the useful life of them is over, its re-utilization becomes inappropriate, and for this reason, the resin is considered radioactive waste. The most common method of treatment is the immobilization of spent ion exchange resin in cement in order to form a solid monolithic matrix, which reduces the radionuclides release into the environment. However, the characteristic of contraction and expansion of the resin limits its incorporation in 10%, resulting in high cost in its direct immobilization. Therefore, it is recommended the utilization of a pre-treatment, capable of reducing the volume and degrading the resin, which would increase the load capacity in the immobilization. This work aims to develop a method of degradation of ion spent resins from the nuclear research reactor of Nuclear and Energy Research Institute (IPEN/CNEN-SP), Brazil, using the Advanced Oxidative Process (AOP) with Fenton's reagent (hydrogen peroxide and ferrous sulphate as catalyst). The resin evaluated was a mixture of cationic (IR 120P) and anionic (IRA 410) resins. The reactions were conducted by varying the concentration of the catalyst (25, 50, 100 e 150 mM) and the volume of the hydrogen peroxide, at three different temperatures, 50, 60 and 70 deg. C. The time of reaction was three hours. Total organic carbon content was determined periodically in order to evaluate the degradation as a function of time. The concentration of 50 mM of catalyst was the most effective in degrading approximately 99%, using up to 330 mL of hydrogen peroxide. The most effective temperature was about 60 deg. C, because of the decomposition of hydrogen peroxide in higher temperatures. TOC content was influenced by the concentration of the catalyst, interfering in the beginning of the

  9. Evaluation of Resin Dissolution Using an Advanced Oxidation Process - 13241

    International Nuclear Information System (INIS)

    The ion-exchange resin is widely used in nuclear reactors, in cooling water purification and removing radioactive elements. Because of the long periods of time inside the reactor system, the resin becomes radioactive. When the useful life of them is over, its re-utilization becomes inappropriate, and for this reason, the resin is considered radioactive waste. The most common method of treatment is the immobilization of spent ion exchange resin in cement in order to form a solid monolithic matrix, which reduces the radionuclides release into the environment. However, the characteristic of contraction and expansion of the resin limits its incorporation in 10%, resulting in high cost in its direct immobilization. Therefore, it is recommended the utilization of a pre-treatment, capable of reducing the volume and degrading the resin, which would increase the load capacity in the immobilization. This work aims to develop a method of degradation of ion spent resins from the nuclear research reactor of Nuclear and Energy Research Institute (IPEN/CNEN-SP), Brazil, using the Advanced Oxidative Process (AOP) with Fenton's reagent (hydrogen peroxide and ferrous sulphate as catalyst). The resin evaluated was a mixture of cationic (IR 120P) and anionic (IRA 410) resins. The reactions were conducted by varying the concentration of the catalyst (25, 50, 100 e 150 mM) and the volume of the hydrogen peroxide, at three different temperatures, 50, 60 and 70 deg. C. The time of reaction was three hours. Total organic carbon content was determined periodically in order to evaluate the degradation as a function of time. The concentration of 50 mM of catalyst was the most effective in degrading approximately 99%, using up to 330 mL of hydrogen peroxide. The most effective temperature was about 60 deg. C, because of the decomposition of hydrogen peroxide in higher temperatures. TOC content was influenced by the concentration of the catalyst, interfering in the beginning of the degradation

  10. Combining Advanced Oxidation Processes: Assessment Of Process Additivity, Synergism, And Antagonism

    International Nuclear Information System (INIS)

    This paper addresses the process interactions from combining integrated processes (such as advanced oxidation processes (AOPs), biological operations, air stripping, etc.). AOPs considered include: Fenton's reagent, ultraviolet light, titanium dioxide, ozone (O3), hydrogen peroxide (H2O2), sonication/acoustic cavitation, among others. A critical review of the technical literature has been performed, and the data has been analyzed in terms of the processes being additive, synergistic, or antagonistic. Predictions based on the individual unit operations are made and compared against the behavior of the combined unit operations. The data reported in this paper focus primarily on treatment of petroleum hydrocarbons and chlorinated solvents. (authors)

  11. Integration of advanced oxidation technologies and biological processes: recent developments, trends, and advances.

    Science.gov (United States)

    Tabrizi, Gelareh Bankian; Mehrvar, Mehrab

    2004-01-01

    The greatest challenge of today's wastewater treatment technology is to optimize the use of biological and chemical wastewater treatment processes. The choice of the process and/or integration of the processes depend strongly on the wastewater characteristics, concentrations, and the desired efficiencies. It has been observed by many investigators that the coupling of a bioreactor and advanced oxidation processes (AOPs) could reduce the final concentrations of the effluent to the desired values. However, optimizing the total cost of the treatment is a challenge, as AOPs are much more expensive than biological processes alone. Therefore, an appropriate design should not only consider the ability of this coupling to reduce the concentration of organic pollutants, but also try to obtain the desired results in a cost effective process. To consider the total cost of the treatment, the residence time in biological and photochemical reactors, the kinetic rates, and the capital and operating costs of the reactors play significant roles. In this study, recent developments and trends (1996-2003) on the integration of photochemical and biological processes for the degradation of problematic pollutants in wastewater have been reviewed. The conditions to get the optimum results from this integration have also been considered. In most of the studies, it has been shown that the integrated processes were more efficient than individual processes. However, slight changes in the configuration of the reactors, temperature, pH, treatment time, concentration of the oxidants, and microorganism's colonies could lead to a great deviation in results. It has also been demonstrated that the treatment cost in both reactors is a function of time, which changes by the flow rate. The minimum cost in the coupling of the processes cannot be achieved unless considering the best treatment time in chemical and biological reactors individually. PMID:15533022

  12. An advanced tunnel oxide layer process for 65 nm NOR floating-gate flash memories

    International Nuclear Information System (INIS)

    An advanced tunnel oxide layer process for 65 nm NOR-type floating-gate flash memory is proposed to improve tunnel oxide quality by an additive sacrificial oxide layer growth. The sacrificial oxide layer process effectively controls the thickness variation of tunnel oxide and improves the flatness of the SiO2/Si interface across the active area. The interface traps’ generation during program/erase cycling of flash cells is found to be reduced, and the reliability property is significantly improved as compared to flash cells without the sacrificial oxide layer process. The technology is applicable to further scaled floating-gate flash memories. (paper)

  13. Comparisons of Three Advanced Oxidation Processes in Organic Matter Removal from Esfahan Composting Factory Leachate

    OpenAIRE

    karimi B.; Ehrampoush M.H.; Mokhtari M.; Ebrahimi A

    2011-01-01

    Backgrounds and Objectives: Wet air oxidation (WAO) is one of the advanced oxidation process which is mostly used to reduce organic matter concentration from industrial wastewater, toxic and non biodegradable substance and solid waste leachate.The objective of this paper is comparisons of three advance oxidation in organic matter removal in different conditions from Esfahan composing factory leachateMaterial and Methods: The experiment was carried out by adding 1.5 Lit pretreated leachate sam...

  14. A comparison of single oxidants versus advanced oxidation processes as chlorine-alternatives for wild blueberry processing (Vaccinium angustifolium).

    Science.gov (United States)

    Crowe, Kristi M; Bushway, Alfred A; Bushway, Rodney J; Davis-Dentici, Katherine; Hazen, Russell A

    2007-05-01

    Advanced oxidation processes and single chemical oxidants were evaluated for their antimicrobial efficacy against common spoilage bacteria isolated from lowbush blueberries. Predominant bacterial flora were identified using biochemical testing with the assessment of relative abundance using non-selective and differential media. Single chemical oxidants evaluated for postharvest processing of lowbush blueberries included 1% hydrogen peroxide, 100 ppm chlorine, and 1 ppm aqueous ozone while advanced oxidation processes (AOPs) included combinations of 1% hydrogen peroxide/UV, 100 ppm chlorine/UV, and 1 ppm ozone/1% hydrogen peroxide/UV. Enterobacter agglomerans and Pseudomonas fluorescens were found to comprise 90-95% of the bacterial flora on lowbush blueberries. Results of inoculation studies reveal significant log reductions (pagglomerans and P. fluorescens on all samples receiving treatment with 1% hydrogen peroxide, 1% hydrogen peroxide/UV, 1 ppm ozone, or a combined ozone/hydrogen peroxide/UV treatment as compared to chlorine treatments and unwashed control berries. Although population reductions approached 2.5 log CFU/g, microbial reductions among these treatments were not found to be significantly different (p< or 5) from each other despite the synergistic potential that should result from AOPs; furthermore, as a single oxidant, UV inactivation of inoculated bacteria was minimal and did not prove effective as a non-aqueous bactericidal process for fresh pack blueberries. Overall, results indicate that hydrogen peroxide and ozone, as single chemical oxidants, are as effective as AOPs and could be considered as chlorine-alternatives in improving the microbiological quality of lowbush blueberries. PMID:17350128

  15. Removal of Organic Matter from Landfill Leachate by Advanced Oxidation Processes: A Review

    OpenAIRE

    Tao Hua; Wei Li; Qixing Zhou

    2010-01-01

    In most countries, sanitary landfill is nowadays the most common way to eliminate municipal solid wastes (MSWs). However, sanitary landfill generates large quantity of heavily polluted leachate, which can induce ecological risk and potential hazards towards public health and ecosystems. The application of advanced oxidation processes (AOPs) including ozone-based oxidation, Fenton oxidation, electrochemical oxidation, and other AOPs to treatment of landfill leachate was reviewed. Th...

  16. Advanced oxide powders processing based on cascade plasma

    International Nuclear Information System (INIS)

    Analysis of the potential advantages offered to thermal spraying and powder processing by the implementation of plasma torches with inter-electrode insert (IEI) or, in other words, cascade plasma torches (CPTs) is presented. The paper provides evidence that the modular designed single cathode CPT helps eliminate the following major disadvantages of conventional plasma torches: plasma parameters drifting, 1-5 kHz pulsing of plasma flow, as well as excessive erosion of electrodes. More stable plasma results in higher quality, homogeneity and reproducibility of plasma sprayed coatings and powders treated. In addition, CPT offers an extremely wide operating window, which allows better control of plasma parameters, particle dwell time and, consequently, particle temperature and velocity within a wide range by generating high enthalpy quasi-laminar plasmas, medium enthalpy transient plasmas, as well as relatively low enthalpy turbulent plasmas. Stable operation, flexibility with plasma gases as well as wide operating window of CPT should help significantly improve the existing plasma spraying processes and coatings, and also help develop new advanced technologies

  17. A comparison between conductive-diamond electrochemical oxidation and other advanced oxidation processes for the treatment of synthetic melanoidins.

    Science.gov (United States)

    Cañizares, P; Hernández-Ortega, M; Rodrigo, M A; Barrera-Díaz, C E; Roa-Morales, G; Sáez, C

    2009-05-15

    In this study, three technologies classified as Advanced Oxidation Processes (Conductive-Diamond Electrochemical Oxidation (CDEO), ozonation and Fenton oxidation) have been compared to treat wastes produced in fermentation processes, and characterized by a significant color and a high organic load. Results of CDEO seem to strongly depend on the addition of an electrolyte salt, not only to decrease the energy cost but also to improve efficiency. The addition of sodium chloride as supporting electrolyte improves the removal percentages of organic load, indicating the important role of mediated oxidation processes carried out by the electrogenerated oxidants (hypochlorite). Fenton oxidation and ozonation seem to be less efficient, and mainly Fenton oxidation favors the accumulation of refractory compounds. The differences observed can be explained in terms of the contribution of hydroxyl radicals and other specific oxidation mechanisms involved in each technology. PMID:18789836

  18. C.I. Reactive Black 5 degradation by advanced electrochemical oxidation process, AEOP

    OpenAIRE

    Esteves, M. de Fátima; Sousa, Elisabete,1954-

    2007-01-01

    In the last decades, an increasing number of procedures to remove pollutants from wastewater have been reported. Advanced oxidation processes (AOPs) are one of those technologies used for this purpose, namely, for textile wastewater treatment. AOPs are environmentally friendly methods based on chemical, photochemical or photocatalytical production of hydroxyl radical (HO•). This strong oxidant can react with most organic compounds present in wastewater, as dyestuffs. In this paper, an Advance...

  19. A novel process of dye wastewater treatment by linking advanced chemical oxidation with biological oxidation

    OpenAIRE

    Zou Haiming; Ma Wanzheng; Wang Yan

    2015-01-01

    Dye wastewater is one of typically non-biodegradable industrial effluents. A new process linking Fenton’s oxidation with biological oxidation proposed in this study was investigated to degrade the organic substances from real dye wastewater. During the combination process, the Fenton’s oxidation process can reduce the organic load and enhance biodegradability of dye wastewater, which is followed by biological aerated filter (BAF) system to further remove organic substances in terms of dischar...

  20. Comparison of advanced oxidation processes used for municipal waste water treatment

    OpenAIRE

    Pavlin, David

    2014-01-01

    Municipal wastewater can be used as an alternative water source. However, it is essential to treat the wastewater, thereby achieving extensive removal of organic pollutants. It is also necessary to ensure a nearly complete decolouration and disinfection of the water. The use of chemical oxidation and thus advanced oxidation processes (AOPs) in the processes of wastewater treatment is important in terms of ensuring an efficient degradation of the more difficult biodegradable or even non-biodeg...

  1. ADVANCED OXIDATION PROCESSES (AOPs) APPLIED FOR WASTEWATER AND DRINKING WATER TREATMENT. ELIMINATION OF PHARMACEUTICALS

    OpenAIRE

    Petrovic, Mira; Radjenovic, Jelena; Barcelo, Damia

    2011-01-01

    Due to their insufficient removal in conventional wastewater treatments, advanced drinking and wastewater treatment options should be considered for the removal of pharmaceutically active compounds (PhACs) from urban, hospital and industrial wastewaters. This paper summarizes the current state-of-the-art in two often applied advanced oxidation processes (AOPs), namely TiO2 assisted photocatalysis and photo-Fenton process. Their possibilities in removing PhACs are discussed, giving examples fo...

  2. Application of advanced oxidation processes for removing salicylic acid from synthetic wastewaters

    Institute of Scientific and Technical Information of China (English)

    Djalma; Ribeiro; da; Silva; Carlos; A.Martinez-Huítle

    2010-01-01

    In this study,advanced oxidation processes(AOPs) such as anodic oxidation(AO),UV/H_2O_2 and Fenton processes(FP) were investigated for the degradation of salicylic acid(SA) in lab-scale experiments.Boron-doped diamond(BDD) film electrodes using Ta as substrates were employed for AO of SA.In the case of FP and UV/H_2O_2,most favorable experimental conditions were determined for each process and these were used for comparing with AO process.The study showed that the FP was the most effective process under ...

  3. A novel process of dye wastewater treatment by linking advanced chemical oxidation with biological oxidation

    Directory of Open Access Journals (Sweden)

    Zou Haiming

    2015-12-01

    Full Text Available Dye wastewater is one of typically non-biodegradable industrial effluents. A new process linking Fenton’s oxidation with biological oxidation proposed in this study was investigated to degrade the organic substances from real dye wastewater. During the combination process, the Fenton’s oxidation process can reduce the organic load and enhance biodegradability of dye wastewater, which is followed by biological aerated filter (BAF system to further remove organic substances in terms of discharge requirement. The results showed that 97.6% of chemical oxygen demand (COD removal by the combination process was achieved at the optimum process parameters: pH of 3.5, H2O2 of 2.0 mL/L, Fe(II of 500 mg/L, 2.0 h treatment time in the Fenton’s oxidation process and hydraulic retention time (HRT of 5 h in the BAF system. Under these conditions, COD concentration of effluent was 72.6 mg/L whereas 3020 mg/L in the influent, thus meeting the requirement of treated dye wastewater discharge performed by Chinese government (less than 100 mg/L. These results obtained here suggest that the new process combining Fenton’s oxidation with biological oxidation may provide an economical and effective alternative for treatment of non-biodegradable industrial wastewater.

  4. Recent Developments in Homogeneous Advanced Oxidation Processes for Water and Wastewater Treatment

    OpenAIRE

    M. Muruganandham; Suri, R. P. S.; Sh. Jafari; M. Sillanpää; Gang-Juan Lee; Wu, J J; M. Swaminathan

    2014-01-01

    This paper reports on recent developments in homogeneous Advanced Oxidation Processes (AOPs) for the treatment of water and wastewater. It has already been established that AOPs are very efficient compared to conventional treatment methods for degradation and mineralization of recalcitrant pollutants present in water and wastewater. AOPs generate a powerful oxidizing agent, hydroxyl radical, which can react with most of the pollutants present in wastewater. Therefore, it is important to dis...

  5. COMPARISON OF DIFFERENT ADVANCED OXIDATION PROCESSES DEGRADING P-CHLOROPHENOL IN AQUEOUS SOLUTION

    OpenAIRE

    H. Movahedyan ، A. M. Seid Mohammadi ، A. Assadi

    2009-01-01

    In present study, degradation of p-chlorophenol using several oxidation systems involving advanced oxidation processes such as ultraviolet/H2O2, microwave/H2O2 and both in the absence of hydrogen peroxide in batch mode by photolytic pilot plant and modified domestic microwave oven was evaluated. The oxidation rate was influenced by many factors, such as the pH value, the amount of hydrogen peroxide, irradiation time and microwave power. The optimum conditions obtained for the best degradation...

  6. Removal of Organic Matter from Landfill Leachate by Advanced Oxidation Processes: A Review

    Directory of Open Access Journals (Sweden)

    Wei Li

    2010-01-01

    Full Text Available In most countries, sanitary landfill is nowadays the most common way to eliminate municipal solid wastes (MSWs. However, sanitary landfill generates large quantity of heavily polluted leachate, which can induce ecological risk and potential hazards towards public health and ecosystems. The application of advanced oxidation processes (AOPs including ozone-based oxidation, Fenton oxidation, electrochemical oxidation, and other AOPs to treatment of landfill leachate was reviewed. The treatment efficiency in term of chemical oxygen demand (COD of various AOPs was presented. Advantages and drawbacks of various AOPs were discussed. Among the AOPs reviewed, Fenton process should be the best choice, not only because it can achieve about 49~89% of COD removal with COD ranging from 837 to 8894 mg/L, but also because the process is cost-effective and simple in technological aspect, there is no mass transfer limitation (homogeneous nature and both iron and hydrogen peroxide are nontoxic.

  7. Toxicity Assessment of Perchloroethylene and Intermediate Products after Advanced Oxidation Process by Daphnia Magna Bioassay

    OpenAIRE

    Mahdi Kargar; Kazem Naddafi; Ramin Nabizadeh

    2014-01-01

    Background and objective: Perchloroethylene is a chlorinated hydrocarbon used as a solvent in many industries and services activities such as dry cleaning and auto industry as degreasing. We carried out a bioassay using Daphnia Magna in order to determine the ecological effects of wastewater treatment through applying advanced oxidation processes (ultrasonic, ultraviolet irradiation and hydrogen peroxide processes) for removal of perchloroethylene. Materials and Methods: Due to the sensiti...

  8. Characterization of plasma-induced phenol advanced oxidation process in a DBD reactor

    OpenAIRE

    Marotta, E.; Ceriani, E.; Shapoval, V.; Schiorlin, M.; Ceretta, C.; Rea, M.; Paradisi, C.

    2011-01-01

    Abstract Using phenol as a model organic pollutant we studied and characterized an innovative advanced oxidation process in water using a prototype dielectric barrier discharge (DBD) reactor in which electrical discharges are produced in the air above the water surface. Phenol is decomposed quite efficiently in this reactor operated at room temperature and atmospheric pressure. The process selectivity to form CO2 is, however, to be improved since a large fraction of the treated org...

  9. Solar-Enhanced Advanced Oxidation Processes for Water Treatment: Simultaneous Removal of Pathogens and Chemical Pollutants

    OpenAIRE

    Oyuna Tsydenova; Valeriy Batoev; Agniya Batoeva

    2015-01-01

    The review explores the feasibility of simultaneous removal of pathogens and chemical pollutants by solar-enhanced advanced oxidation processes (AOPs). The AOPs are based on in-situ generation of reactive oxygen species (ROS), most notably hydroxyl radicals •OH, that are capable of destroying both pollutant molecules and pathogen cells. The review presents evidence of simultaneous removal of pathogens and chemical pollutants by photocatalytic processes, namely TiO2 photocatalysis and photo-Fe...

  10. Treatment of Textile Wastewater by Combining Biological Processes and Advanced Oxidation

    OpenAIRE

    Punzi, Marisa

    2015-01-01

    Treatment of textile wastewater is challenging because the water contains toxic compounds that have low biodegradability. Dyes, detergents, surfactants, biocides and more are used to improve the textile process and to make the clothes resistant to physical, chemical and biological agents. New technologies have been developed in the last decades and in particular Advanced Oxidation Processes (AOPs) have shown considerable potential for treatment of industrial effluents. These pr...

  11. Degradation of the commercial surfactant nonylphenol ethoxylate by advanced oxidation processes

    International Nuclear Information System (INIS)

    Highlights: • NP4EO in industrial effluents can be treated before reaching water reservoirs. • Advanced oxidation processes are proposed for the degradation of NP4EO. • The degradation rate depends mainly on the light intensity. • The mineralization rate depends mainly on the current density. • Photo-assisted electrochemical oxidation showed the best degradation results. - Abstract: Four different oxidation process, namely direct photolysis (DP) and three advanced oxidation processes (heterogeneous photocatalysis – HP, eletrochemical oxidation – EO and photo-assisted electrochemical oxidation – PEO) were applied in the treatment of wastewater containing nonylphenol ethoxylate (NPnEO). The objective of this work was to determine which treatment would be the best option in terms of degradation of NPnEO without the subsequent generation of toxic compounds. In order to investigate the degradation of the surfactant, the processes were compared in terms of UV/Vis spectrum, mineralization (total organic carbon), reaction kinetics, energy efficiency and phytotoxicity. A solution containing NPnEO was prepared as a surrogate of the degreasing wastewater, was used in the processes. The results showed that the photo-assisted processes degrade the surfactant, producing biodegradable intermediates in the reaction. On the other hand, the electrochemical process influences the mineralization of the surfactant. The process of PEO carried out with a 250 W lamp and a current density of 10 mA/cm2 showed the best results in terms of degradation, mineralization, reaction kinetics and energy consumption, in addition to not presenting phytotoxicity. Based on this information, this process can be a viable alternative for treating wastewater containing NPnEO, avoiding the contamination of water resources

  12. Pretreatment of whole blood using hydrogen peroxide and UV irradiation. Design of the advanced oxidation process

    OpenAIRE

    Bragg, Stefanie A.; Armstrong, Kristie C.; Xue, Zi-Ling

    2012-01-01

    A new process to pretreat blood samples has been developed. This process combines the Advanced Oxidation Process (AOP) treatment (using H2O2 and UV irradiation) with acid deactivation of the enzyme catalase in blood. A four-cell reactor has been designed and built in house. The effect of pH on the AOP process has been investigated. The kinetics of the pretreatment process shows that at high CH2O2,t = 0, the reaction is zeroth order with respect to CH2O2 and first order with respect to Cblood....

  13. The Study of LeachateTreatment by Using Three Advanced Oxidation Process Based Wet air Oxidation

    Directory of Open Access Journals (Sweden)

    Behroz Karimi

    2013-01-01

    Full Text Available Wet air oxidation is regarded as appropriate options for wastewater treatment with average organic compounds. The general purpose of this research is to determine the efficiency of three wet air oxidation methods, wet oxidation with hydrogen peroxide and absorption with activated carbon in removing organic matter and nitrogenous compounds from Isfahan's urban leachate. A leachate sample with the volume of 1.5 liters entered into a steel reactor with the volume of three liters and was put under a 10-bar pressure, at temperatures of 100, 200, and 300[degree sign] as well as three retention times of 30, 60, and 90 minutes. The sample was placed at 18 stages of leachate storage ponds in Isfahan Compost Plant with the volume of 20 liters, using three WPO, WAO methods and a combination of WAO/GAC for leachate pre-treatment. Thirty percent of pure oxygen and hydrogen peroxide were applied as oxidation agents. The COD removal efficiency in WAO method is 7.8-33.3%, in BOD is 14.7-50.6%, the maximum removal percentage (efficiency for NH4-N is 53.3% and for NO3-N is 56.4-73.9%. The removal efficiency of COD and BOD5 is 4.6%-34 and 24%-50 respectively in WPO method. Adding GAC to the reactor, the removal efficiency of all parameters was improved. The maximum removal efficiency was increased 48% for COD, 31%-43.6 for BOD5 by a combinational method, and the ratio of BOD5/COD was also increased to 90%. In this paper, WAO and WPO process was used for Leachate pre-treatment and WAO/GAC combinational process was applied for improving the organic matter removal and leachate treatment; it was also determined that the recent process is much more efficient in removing resistant organic matter.

  14. Removal of micro-pollutants from drinking water with advanced oxidation processes

    OpenAIRE

    Sander, Fabian

    2009-01-01

    This thesis determines the feasibility of ozone gas and ultraviolet (UV)technologies to reduce pollutants from drinking water. The merging of both techniques, ozone and UV, is known as a so called advanced oxidation process (AOP). ITT Wedeco is developing new technologies to meet the growing concern of water works to remove micro-pollutants from their water. The emphasis of this work was put on the formation of the oxidation by-product bromate and the removal of the solvent 1.4 dioxane fr...

  15. Recycling of textile wastewaters treated with various combinations of advanced oxidation processes (AOP)

    OpenAIRE

    Krivograd Klemenčič, Aleksandra; Krzyk, Mario; Drev, Darko; Balabanič, Damjan; Kompare, Boris

    2012-01-01

    Advanced oxidation processes (AOPs) are widely used for treatment of wastewaters containing recalcitrant organic compounds from industrial and municipal wastewater; many advantages over other technologies have been found and good treatment results have been obtained so far. Approaches which reduce fresh water consumption are especially important for regions with shortage in fresh water resources and in high waterconsuming industries. Within AOP4Water (a multinational project funde...

  16. Study on the Hot Extrusion Process of Advanced Radiation Resistant Oxide Dispersion Strengthened Steel Tubes

    International Nuclear Information System (INIS)

    Ferritic/martensitic steel has a better thermal conductivity and swelling resistance than austenitic stainless steel. Unfortunately, the available temperature range of ferritic/martensitic steel is limited at up to 650 .deg. C. Oxide dispersion strengthened (ODS) steels have been developed as the most prospective core structural materials for next generation nuclear systems because of their excellent high strength and irradiation resistance. The material performances of this new alloy are attributed to the existence of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperature in a ferritic/martensitic matrix. This microstructure can be very attractive in achieving superior mechanical properties at high temperatures, and thus, these favorable microstructures should be obtained through the controls of the fabrication process parameters during the mechanical alloying and hot consolidation procedures. In this study, a hot extrusion process for advanced radiation resistant ODS steel tube was investigated. ODS martensitic steel was designed to have high homogeneity, productivity, and reproducibility. Mechanical alloying and hot consolidation processes were employed to fabricate the ODS steels. A microstructure observation and creep rupture test were examined to investigate the effects of the optimized fabrication conditions. Advanced radiation resistant ODS steel has been designed to have homogeneity, productivity, and reproducibility. For these characteristics, modified mechanical alloying and hot consolidation processes were developed. Microstructure observation revealed that the ODS steel has uniformly distributed fine-grain nano-oxide particles. The fabrication process for the tubing is also being propelled in earnest

  17. Post-treatment of reclaimed waste water based on an electrochemical advanced oxidation process

    Science.gov (United States)

    Verostko, Charles E.; Murphy, Oliver J.; Hitchens, G. D.; Salinas, Carlos E.; Rogers, Tom D.

    1992-01-01

    The purification of reclaimed water is essential to water reclamation technology life-support systems in lunar/Mars habitats. An electrochemical UV reactor is being developed which generates oxidants, operates at low temperatures, and requires no chemical expendables. The reactor is the basis for an advanced oxidation process in which electrochemically generated ozone and hydrogen peroxide are used in combination with ultraviolet light irradiation to produce hydroxyl radicals. Results from this process are presented which demonstrate concept feasibility for removal of organic impurities and disinfection of water for potable and hygiene reuse. Power, size requirements, Faradaic efficiency, and process reaction kinetics are discussed. At the completion of this development effort the reactor system will be installed in JSC's regenerative water recovery test facility for evaluation to compare this technique with other candidate processes.

  18. Oxidative treatment of a waste water stream from a molasses processing using ozone and advanced oxidation technologies

    International Nuclear Information System (INIS)

    The discoloration of a biologically pretreated waste water stream from a molasses processing by ozonation and two advanced oxidation processes (O3/H2O2 and O3/γ-irradiation, respectively) was studied. Colour removal occurred with all three processes with almost the same efficiency. The main difference of the methods applied was reflected by the BOD increase during the discoloration period. By ozonation it was much higher than by AOPs but it also appeared with AOPs. AOPs were, therefore, not apt for an effective BOD control during discoloration. (authors)

  19. Identification of transformation products during advanced oxidation of diatrizoate: Effect of water matrix and oxidation process.

    Science.gov (United States)

    Azerrad, Sara P; Lütke Eversloh, Christian; Gilboa, Maayan; Schulz, Manoj; Ternes, Thomas; Dosoretz, Carlos G

    2016-10-15

    Removal of micropollutants from reverse osmosis (RO) brines of wastewater desalination by oxidation processes is influenced by the scavenging capacity of brines components, resulting in the accumulation of transformation products (TPs) rather than complete mineralization. In this work the iodinated contrast media diatrizoate (DTZ) was used as model compound due to its relative resistance to oxidation. Identification of TPs was performed in ultrapure water (UPW) and RO brines applying nonthermal plasma (NTP) and UVA-TiO2 as oxidation techniques. The influence of main RO brines components in the formation and accumulation of TPs, such as chloride, bicarbonate alkalinity and humic acid, was also studied during UVA-TiO2. DTZ oxidation pattern in UPW resulted similar in both UVA-TiO2 and NTP achieving 66 and 61% transformation, respectively. However, DTZ transformation in RO brines was markedly lower in UVA-TiO2 (9%) than in NTP (27%). These differences can be attributed to the synergic effect of RO brines components during NTP. Moreover, reactive species other than hydroxyl radical contributed to DTZ transformation, i.e., direct photolysis in UVA-TiO2 and direct photolysis + O3 in NTP accounted for 16 and 23%, respectively. DTZ transformation led to iodide formation in both oxidation techniques but it further oxidized to iodate by ozone in NTP. In total 14 transformation products were identified in UPW of which 3 were present only in UVA-TiO2 and 2 were present exclusively in NTP; 5 of the 14 TPs were absent in RO brines. Five of them were new and were denoted as TP-474A/B, TP-522, TP-586, TP-602, TP-628. TP-522 (mono-chlorinated) was elucidated only in presence of high chloride titer-synthetic water matrix in NTP, most probably formed by active chlorine species generated in situ. TPs accumulation in RO brines was markedly different in comparison to UPW. This denotes the influence of RO brines components in the formation of reactive species that could further attack

  20. Reduction of antibiotic resistance genes in municipal wastewater effluent by advanced oxidation processes.

    Science.gov (United States)

    Zhang, Yingying; Zhuang, Yao; Geng, Jinju; Ren, Hongqiang; Xu, Ke; Ding, Lili

    2016-04-15

    This study investigated the reduction of antibiotic resistance genes (ARGs), intI1 and 16S rRNA genes, by advanced oxidation processes (AOPs), namely Fenton oxidation (Fe(2+)/H2O2) and UV/H2O2 process. The ARGs include sul1, tetX, and tetG from municipal wastewater effluent. The results indicated that the Fenton oxidation and UV/H2O2 process could reduce selected ARGs effectively. Oxidation by the Fenton process was slightly better than that of the UV/H2O2 method. Particularly, for the Fenton oxidation, under the optimal condition wherein Fe(2+)/H2O2 had a molar ratio of 0.1 and a H2O2 concentration of 0.01molL(-1) with a pH of 3.0 and reaction time of 2h, 2.58-3.79 logs of target genes were removed. Under the initial effluent pH condition (pH=7.0), the removal was 2.26-3.35 logs. For the UV/H2O2 process, when the pH was 3.5 with a H2O2 concentration of 0.01molL(-1) accompanied by 30min of UV irradiation, all ARGs could achieve a reduction of 2.8-3.5 logs, and 1.55-2.32 logs at a pH of 7.0. The Fenton oxidation and UV/H2O2 process followed the first-order reaction kinetic model. The removal of target genes was affected by many parameters, including initial Fe(2+)/H2O2 molar ratios, H2O2 concentration, solution pH, and reaction time. Among these factors, reagent concentrations and pH values are the most important factors during AOPs. PMID:26815295

  1. Comparisons of Three Advanced Oxidation Processes in Organic Matter Removal from Esfahan Composting Factory Leachate

    Directory of Open Access Journals (Sweden)

    karimi B.

    2011-06-01

    Full Text Available Backgrounds and Objectives: Wet air oxidation (WAO is one of the advanced oxidation process which is mostly used to reduce organic matter concentration from industrial wastewater, toxic and non biodegradable substance and solid waste leachate.The objective of this paper is comparisons of three advance oxidation in organic matter removal in different conditions from Esfahan composing factory leachateMaterial and Methods: The experiment was carried out by adding 1.5 Lit pretreated leachate sample to 3Lit autoclave reactor and adding 10 bar pressure at temperature of 100, 200 and 300 °C and pressure (10 bars with retention time of 30, 60 and 90 min. leachate sample in 18 stages from composting factory in Isfahan in the volume of 20 lit was taken and the three methodsWAO, WPO, and a combination of WAO/GAC were used for pre-treatments. Pure oxygen and 30% hydrogen peroxide was used as oxidation agent.Results: The result shows significant improvement on the removal rate of COD (7.8-33.3%, BOD5 (14.7-50.6%by WAO process.The removal efficiency of 4.6-34% COD, 24-50% BOD, was observed in the reactor.Adding theGACto the reactor improved removal efficiency of all parameters.Combination Process (WAO/GAC removed 48% of COD, 31-43.6% of BOD.Combination process demonstrated higher efficiency than two other previous methods as BOD5/COD ratio of 90% achieved.Conclusion: The WAO process presented in this paper is efficient for pretreatment of leachate, And the modified WPO process remove organic materials and ammonia moreover WAO/GAC can be considered as an excellent alternative treatment for removing reluctant organic matter (COD, BOD5 and organic nitrogen compounds, which found in leachate.

  2. Chemical oxygen demand reduction in coffee wastewater through chemical flocculation and advanced oxidation processes

    Institute of Scientific and Technical Information of China (English)

    ZAYAS Pérez Teresa; GEISSLER Gunther; HERNANDEZ Fernando

    2007-01-01

    The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculatio and advanced oxidation processes(AOP)had been studied.The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202,UVO3 and UV/H-H202/O3 processes was determined under acidic conditions.For each of these processes,different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater.Coffee wastewater is characterized by a high chemical oxygen demand(COD)and low total suspended solids.The outcomes of coffee wastewater reeatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD,color,and turbidity.It was found that a reductiOn in COD of 67%could be realized when the coffee wastewater was treated by chemical coagulation-flocculatlon witll lime and coagulant T-1.When coffee wastewater was treated by coagulation-flocculation in combination with UV/H202,a COD reduction of 86%was achieved,although only after prolonged UV irradiation.Of the three advanced oxidation processes considered,UV/H202,uv/03 and UV/H202/03,we found that the treatment with UV/H2O2/O3 was the most effective,with an efficiency of color,turbidity and further COD removal of 87%,when applied to the flocculated coffee wastewater.

  3. Chemical oxygen demand reduction in coffee wastewater through chemical flocculation and advanced oxidation processes.

    Science.gov (United States)

    Zayas Pérez, Teresa; Geissler, Gunther; Hernandez, Fernando

    2007-01-01

    The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes (AOP) had been studied. The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H2O2, UV/O3 and UV/H2O2/O3 processes was determined under acidic conditions. For each of these processes, different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater. Coffee wastewater is characterized by a high chemical oxygen demand (COD) and low total suspended solids. The outcomes of coffee wastewater treatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD, color, and turbidity. It was found that a reduction in COD of 67% could be realized when the coffee wastewater was treated by chemical coagulation-flocculation with lime and coagulant T-1. When coffee wastewater was treated by coagulation-flocculation in combination with UV/H2O2, a COD reduction of 86% was achieved, although only after prolonged UV irradiation. Of the three advanced oxidation processes considered, UV/H2O2, UV/O3 and UV/H2O2/O3, we found that the treatment with UV/H2O2/O3 was the most effective, with an efficiency of color, turbidity and further COD removal of 87%, when applied to the flocculated coffee wastewater. PMID:17918591

  4. COMPARISON OF DIFFERENT ADVANCED OXIDATION PROCESSES DEGRADING P-CHLOROPHENOL IN AQUEOUS SOLUTION

    Directory of Open Access Journals (Sweden)

    H. Movahedyan ، A. M. Seid Mohammadi ، A. Assadi

    2009-07-01

    Full Text Available In present study, degradation of p-chlorophenol using several oxidation systems involving advanced oxidation processes such as ultraviolet/H2O2, microwave/H2O2 and both in the absence of hydrogen peroxide in batch mode by photolytic pilot plant and modified domestic microwave oven was evaluated. The oxidation rate was influenced by many factors, such as the pH value, the amount of hydrogen peroxide, irradiation time and microwave power. The optimum conditions obtained for the best degradation rate were pH=7 and H2O2 concentration of 0.05 mol/L for ultraviolet/H2O2 system and pH=10.5, H2O2 concentration of about 0.1 mol/L and microwave irradiation power of about 600W for microwave/H2O2 system at constant p-chlorophenol concentration. The degradation of p-chlorophenol by different types of oxidation processes followed first order rate decay kinetics. The rate constants were 0.137, 0.012, 0.02 and 0.004/min1 for ultraviolet/H2O2, microwave/H2O2, ultraviolet and microwave irradiation alone. Finally a comparison of the specific energy consumption showed that ultraviolet/H2O2 process reduced the energy consumption by at least 67% compared with the microwave/H2O2 process.

  5. An investigation to adopt zero liquid discharge in textile dyeing using advanced oxidation processes

    International Nuclear Information System (INIS)

    In this study, a novel idea of using ozone oxidation at the end of reactive dyeing process was explored in order to achieve zero discharge dyeing. An advanced oxidative treatment was given during the dyeing process to remove unfixed and hydrolyzed reactive dyes from cotton substrate. Three different shades were dyed using vinylsulphone reactive class of dyes. At the end of fixation step, washing of fabrics was carried out using appropriate quantities of ozone in the process. Ozone oxidation continued until the liquor was decolorized around 95-100% and COD (Chemical Oxygen Demand) was reduced about 80-90%, thus achieving zero liquid discharge dyeing process. The decolouration efficiency of wastewater was regarded as an indicative of removal of dyes from the textile materials because fabric was being washed continuously in the same liquor. Fabric samples dyed with conventional and new methods were compared in terms of change in shade, colourfastness properties, colour stripping, and fabric appearance. Overall results showed that the use of ozone during reactive dyeing can result in less water consumption, reduced process time, and zero discharge of coloured effluents from textile dyeing factories. (author)

  6. Electrochemical advanced oxidation and biological processes for wastewater treatment: a review of the combined approaches.

    Science.gov (United States)

    Ganzenko, Oleksandra; Huguenot, David; van Hullebusch, Eric D; Esposito, Giovanni; Oturan, Mehmet A

    2014-01-01

    As pollution becomes one of the biggest environmental challenges of the twenty-first century, pollution of water threatens the very existence of humanity, making immediate action a priority. The most persistent and hazardous pollutants come from industrial and agricultural activities; therefore, effective treatment of this wastewater prior to discharge into the natural environment is the solution. Advanced oxidation processes (AOPs) have caused increased interest due to their ability to degrade hazardous substances in contrast to other methods, which mainly only transfer pollution from wastewater to sludge, a membrane filter, or an adsorbent. Among a great variety of different AOPs, a group of electrochemical advanced oxidation processes (EAOPs), including electro-Fenton, is emerging as an environmental-friendly and effective treatment process for the destruction of persistent hazardous contaminants. The only concern that slows down a large-scale implementation is energy consumption and related investment and operational costs. A combination of EAOPs with biological treatment is an interesting solution. In such a synergetic way, removal efficiency is maximized, while minimizing operational costs. The goal of this review is to present cutting-edge research for treatment of three common and problematic pollutants and effluents: dyes and textile wastewater, olive processing wastewater, and pharmaceuticals and hospital wastewater. Each of these types is regarded in terms of recent scientific research on individual electrochemical, individual biological and a combined synergetic treatment. PMID:24965093

  7. The study of leachate treatment by using three advanced oxidation process based wet air oxidation

    OpenAIRE

    Mokhtari Mehdi; Ebrahimi Asghar; Ehrampoush Mohammad Hassan; Karimi Behroz

    2013-01-01

    Abstract Wet air oxidation is regarded as appropriate options for wastewater treatment with average organic compounds. The general purpose of this research is to determine the efficiency of three wet air oxidation methods, wet oxidation with hydrogen peroxide and absorption with activated carbon in removing organic matter and nitrogenous compounds from Isfahan's urban leachate. A leachate sample with the volume of 1.5 liters entered into a steel reactor with the volume of three liters and was...

  8. The Study of LeachateTreatment by Using Three Advanced Oxidation Process Based Wet air Oxidation

    OpenAIRE

    Behroz Karimi; Mohammad Hassan Ehrampoush; Asghar Ebrahimi; Mehdi Mokhtari

    2013-01-01

    Wet air oxidation is regarded as appropriate options for wastewater treatment with average organic compounds. The general purpose of this research is to determine the efficiency of three wet air oxidation methods, wet oxidation with hydrogen peroxide and absorption with activated carbon in removing organic matter and nitrogenous compounds from Isfahan's urban leachate. A leachate sample with the volume of 1.5 liters entered into a steel reactor with the volume of three liters and was put unde...

  9. Comparison Between the Efficiency of Advanced Oxidation Process and Coagulation for Removal Organophosphorus and Carbamat Pesticides

    OpenAIRE

    A.R Rahmani; M.T. Samadi; M Khodadadi

    2011-01-01

    Background and Objectives: Water pollution by pesticides has adverse effects on the environment and human health, as well .In recent years, advanced oxidation processes, have been gone through to a very high degree for pesticides removal. Poly-Aluminum chloride (PAC) used for water treatment, can be effective on pesticides removal. The aim of this research was to study the use of UV/O3 and PAC in the removal of pesticides from drinking water.Materials and Methods: In this descriptive- an...

  10. Antibiotic abatement in different advanced oxidation processes coupled with a biological sequencing batch biofilm reactor

    International Nuclear Information System (INIS)

    During the last decade, the lack of fresh water is becoming a major concern. Recently, the present of recalcitrant products such as pharmaceuticals has caused a special interest due to their undefined environmental impact. Among these antibiotics are one of the numerous recalcitrant pollutants present in surface waters that might not be completely removed in the biological stage of sewage treatment plants because of their antibacterial nature. Advanced Oxidation Processes (AOPs) have proved to be highly efficient for the degradation of most organic pollutants in wastewaters. (Author)

  11. A study on the enhancement of sonochemical degradation of eosin B using other advanced oxidation processes

    OpenAIRE

    Goel, Mukesh; Das, Ashutosh; Ravikumar, K.; ASTHANA, ABHISHEK

    2014-01-01

    Eosin B is a xanthenes dye and is a derivate of fluorescein. The efficacy of sonochemical degradation coupled with other advanced oxidation process (AOP’s) has been studied for eosin B degradation in aqueous solution. The study compares the effects of H2O2 concentration, saturating gas (argon, N2, and O2), temperature and pH (3–11). Furthermore, kinetic comparison and a figure of merit for the electrical energy consumption were carried out for the degradation under combination of different AO...

  12. Advanced oxidation processes of decomposing dichloroacetic acid and trichloroacetic acid in water

    Institute of Scientific and Technical Information of China (English)

    WANG Kun-ping; GUO Jin-song; YANG Min; JUNJI Hirotsuji; DENG Rong-sen; LIU Wei

    2008-01-01

    We studied the decomposition of two haloacetic acids (HAAs), dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA), in water by single oxidants ozone (O3) and ultraviolet radiation (UV) and the advanced oxidation processes (AOPs) constituted by the combinations of O3/UV, H2O2/UV, O3 /H2O2, and O3/H2O2/UV. The concentrations of HAAs were analyzed at specified time intervals to track their decomposition. Except for O3 and UV, the four combined oxidation processes remarkably enhance the decomposition of DCAA and TCAA owing to the generated very reactive hydroxyl radicals. The fastest decomposition process is O3/H2O2/UV, closely followed by O3/UV. DCAA is much easier to decompose than TCAA. The kinetics of HAA decomposition by O3/UV can be described well by a pseudo first-order reaction model under a constant initial dissolved O3 concentration and fixed UV radiation. Humic acids and HCO3- in the reaction system both decrease the decomposition rate constants for DCAA and TCAA. The amount of H2O2 accumulates in the presence of humic acids in the O3/UV process.

  13. Color, TOC and AOX removals from pulp mill effluent by advanced oxidation processes: A comparative study

    International Nuclear Information System (INIS)

    Pulp mill effluent containing toxic chemicals was treated by different advanced oxidation processes (AOPs) consisting of treatments by hydrogen peroxide, Fenton's reagent (H2O2/Fe2+), UV, UV/H2O2, photo-Fenton (UV/H2O2/Fe2+), ozonation and peroxone (ozone/H2O2) in laboratory-scale reactors for color, total organic carbon (TOC) and adsorbable organic halogens (AOX) removals from the pulp mill effluent. Effects of some operating parameters such as the initial pH, oxidant and catalyst concentrations on TOC, color, AOX removals were investigated. Almost every method used resulted in some degree of color removal from the pulp mill effluent. However, the Fenton's reagent utilizing H2O2/Fe2+ resulted in the highest color, TOC and AOX removals under acidic conditions when compared with the other AOPs tested. Approximately, 88% TOC, 85% color and 89% AOX removals were obtained by the Fenton's reagent at pH 5 within 30 min. Photo-Fenton process yielded comparable TOC (85%), color (82%) and AOX (93%) removals within 5 min due to oxidations by UV light in addition to the Fenton's reagent. Fast oxidation reactions by the photo-Fenton treatment makes this approach more favorable as compared to the others used

  14. Degradation of estrone in water and wastewater by various advanced oxidation processes.

    Science.gov (United States)

    Sarkar, Shubhajit; Ali, Sura; Rehmann, Lars; Nakhla, George; Ray, Madhumita B

    2014-08-15

    A comprehensive study was conducted to determine the relative efficacy of various advanced oxidation processes such as O3, H2O2, UV, and combinations of UV/O3, UV/H2O2 for the removal of estrone (E1) from pure water and secondary effluent. In addition to the parent compound (E1) removal, performance of the advanced oxidation processes was characterized using removal of total organic carbon (TOC), and estrogenicity of the effluent. Although E1 removal was high for all the AOPs, intermediates formed were more difficult to degrade leading to slow TOC removal. Energy calculations and cost analysis indicated that, although UV processes have low electricity cost, ozonation is the least cost option ($ 0.34/1000 gallons) when both capital and operating costs were taken into account. Ozonation also is superior to the other tested AOPs due to higher removal of TOC and estrogenicity. The rate of E1 removal decreased linearly with the background TOC in water, however, E1 degradation in the secondary effluent from a local wastewater treatment plant was not affected significantly due to the low COD values in the effluent. PMID:24937659

  15. Recent Developments in Homogeneous Advanced Oxidation Processes for Water and Wastewater Treatment

    Directory of Open Access Journals (Sweden)

    M. Muruganandham

    2014-01-01

    Full Text Available This paper reports on recent developments in homogeneous Advanced Oxidation Processes (AOPs for the treatment of water and wastewater. It has already been established that AOPs are very efficient compared to conventional treatment methods for degradation and mineralization of recalcitrant pollutants present in water and wastewater. AOPs generate a powerful oxidizing agent, hydroxyl radical, which can react with most of the pollutants present in wastewater. Therefore, it is important to discuss recent developments in AOPs. The homogeneous AOPs such as O3, UV/O3, UV/O3/H2O2, and UV/H2O2, Fe2+/H2O2, UV/Fe2+/H2O2 on the degradation of pollutants are discussed in this paper. The influence on the process efficiency of various experimental parameters such as solution pH, temperature, oxidant concentration, and the dosage of the light source is discussed. A list of contaminants used for degradation by various AOPs and the experimental conditions used for the treatment are discussed in detail.

  16. Use of solar advanced oxidation processes for wastewater treatment : follow-up on degradation products, acute toxicity, genotoxicity and estrogenicity

    OpenAIRE

    Brienza, M.; Ahmed, M.M; Escande, A; Plantard, G.; Scrano, L.; Chiron, Serge; Bufo, S. A.; Goetz, V.

    2016-01-01

    Wastewater tertiary treatment by advanced oxidation processes is thought to produce a treated effluent with lower toxicity than the initial influent. Here we performed tertiary treatment of a secondary effluent collected from a Waste Water Treatment Plant via homogeneous (solar/HSO5-/Fe2+) and heterogeneous (solar/TiO2) solar advanced oxidation aiming at the assessment of their effectiveness in terms of contaminants' and toxicity abatement in a plain solar reactor. A total of 53 organic conta...

  17. Unexpected toxicity to aquatic organisms of some aqueous bisphenol A samples treated by advanced oxidation processes.

    Science.gov (United States)

    Tišler, Tatjana; Erjavec, Boštjan; Kaplan, Renata; Şenilă, Marin; Pintar, Albin

    2015-01-01

    In this study, photocatalytic and catalytic wet-air oxidation (CWAO) processes were used to examine removal efficiency of bisphenol A from aqueous samples over several titanate nanotube-based catalysts. Unexpected toxicity of bisphenol A (BPA) samples treated by means of the CWAO process to some tested species was determined. In addition, the CWAO effluent was recycled five- or 10-fold in order to increase the number of interactions between the liquid phase and catalyst. Consequently, the inductively coupled plasma mass spectrometry (ICP-MS) analysis indicated higher concentrations of some toxic metals like chromium, nickel, molybdenum, silver, and zinc in the recycled samples in comparison to both the single-pass sample and the photocatalytically treated solution. The highest toxicity of five- and 10-fold recycled solutions in the CWAO process was observed in water fleas, which could be correlated to high concentrations of chromium, nickel, and silver detected in tested samples. The obtained results clearly demonstrated that aqueous samples treated by means of advanced oxidation processes should always be analyzed using (i) chemical analyses to assess removal of BPA and total organic carbon from treated aqueous samples, as well as (ii) a battery of aquatic organisms from different taxonomic groups to determine possible toxicity. PMID:26114268

  18. Removal of persistent organic pollutant hexachlorocyclohexane isomers by advanced oxidation process.

    Science.gov (United States)

    2012-04-01

    Organochlorine insecticide Lindane (gamma-Hexachlorocyclohexane) and its isomers (alpha, beta, delta-HCH) are recalcitrant and toxic compounds. They were progressively banished in most of the countries, because of their persistence and toxicity. Due to their nonselective production process and widespread use, they are still occurring in the environment. These insecticides and isomers were detected in all media like soil, ground water, sediments, vegetables and even in human tissues. In this study, UV, H2O2, UV+H2O2, Fenton's reagent, UV+Fenton's reagent, Advanced Oxidation Process (AOP) have been applied for degradation of HCH isomers (a, beta, gamma and delta-HCH). The results revealed that the UV+H2O2 treatment was most effective, which could do 99% degradation of all isomers of HCH within 75 minutes. The results in detail are presented and discussed in this paper. PMID:24749381

  19. Application of advanced oxidation processes (AOPs) for the treatment of a particular industrial wastewater

    International Nuclear Information System (INIS)

    The present paper refers about the use of some advanced oxidation processes for the treatment of a particular industrial wastewater polluted by organic acids and solvents. Such waste is generated during the electrodeposition of paint in cathodic technological systems (cataphoresis). The AOPs studied were the following: H2O2-UV, O3 in strongly alkaline media and Fe(met)-H2O2. The latter which represents a derivation of the Fenton process gave the best results in terms of reaction times, costs in management and reduction rate of organic matter. Its efficiency was also confirmed by some laboratory tests made on synthetic samples. The reactors used to perform the experiments with ozone and H2O2-UV were especially created. The degradation of the organic compounds was quantified by monitoring the COD parameter and in some cases by detecting the concentration of each individual pollutant

  20. Insights into real cotton-textile dyeing wastewater treatment using solar advanced oxidation processes.

    Science.gov (United States)

    Soares, Petrick A; Silva, Tânia F C V; Manenti, Diego R; Souza, Selene M A G U; Boaventura, Rui A R; Vilar, Vítor J P

    2014-01-01

    Different advanced oxidation processes (AOPs) were applied to the treatment of a real cotton-textile dyeing wastewater as a pre-oxidation step to enhance the biodegradability of the recalcitrant compounds, which can be further oxidized using a biological process. Tests were conducted on a lab-scale prototype using artificial solar radiation and at pilot scale with compound parabolic collectors using natural solar radiation. The cotton-textile dyeing wastewater presents a lilac color, with a maximum absorbance peak at 641 nm, alkaline pH (pH = 8.2), moderate organic content (DOC = 152 mg C L(-1), COD = 684 mg O2 L(-1)) and low-moderate biodegradability (40 % after 28 days in Zahn-Wellens test). All the tested processes contributed to an effective decolorization and mineralization, but the most efficient process was the solar-photo-Fenton with an optimum catalyst concentration of 60 mg Fe(2+) L(-1), leading to 98.5% decolorization and 85.5% mineralization after less than 0.1 and 5.8 kJUV L(-1), respectively. In order to achieve a final wastewater with a COD below 250 mg O2 L(-1) (discharge limit into water bodies imposed by the Portuguese Legislation-Portaria no. 423/97 of 25 June 1997), considering the combination of a solar-photo-Fenton reaction with a biological process, the phototreatment energy required is 0.5 kJUV L(-1), consuming 7.5 mM hydrogen peroxide, resulting in 58.4% of mineralization [Formula: see text]. PMID:23832802

  1. Application of several advanced oxidation processes for the destruction of terephthalic acid (TPA)

    International Nuclear Information System (INIS)

    Terephthalic acid (TPA) is widely applied as a raw material in making polyester fiber, polyethylene terephthalate (PET) bottles, polyester films, etc. TPA is toxic and is known to act as endocrine disruptor. TPA wastewater is traditionally treated by biological process and this study aims to evaluate the effectiveness of several advanced oxidation processes on TPA removal. The oxidation processes studied were: UV-TiO2, UV-H2O2, UV-H2O2-Fe, O3, O3/Fe, O3/TiO2, UV-O3-H2O2-Fe and UV-O3-H2O2-Fe-TiO2. The results indicate that the time required for the complete destruction of 50 ppm of TPA can be minimized from 10 h using UV-TiO2 system, to less than 10 min by UV-H2O2-Fe-O3 system. Some of the likely organic intermediates identified during TPA destruction include, benzoquinone, benzene, maleic acid and oxalic acid. Possible destruction pathway of TPA has been proposed. TPA degradation by various systems was also analyzed based on the reaction kinetics and operating costs

  2. Combination of Advanced Oxidation Processes and biological treatments for wastewater decontamination--a review.

    Science.gov (United States)

    Oller, I; Malato, S; Sánchez-Pérez, J A

    2011-09-15

    Nowadays there is a continuously increasing worldwide concern for development of alternative water reuse technologies, mainly focused on agriculture and industry. In this context, Advanced Oxidation Processes (AOPs) are considered a highly competitive water treatment technology for the removal of those organic pollutants not treatable by conventional techniques due to their high chemical stability and/or low biodegradability. Although chemical oxidation for complete mineralization is usually expensive, its combination with a biological treatment is widely reported to reduce operating costs. This paper reviews recent research combining AOPs (as a pre-treatment or post-treatment stage) and bioremediation technologies for the decontamination of a wide range of synthetic and real industrial wastewater. Special emphasis is also placed on recent studies and large-scale combination schemes developed in Mediterranean countries for non-biodegradable wastewater treatment and reuse. The main conclusions arrived at from the overall assessment of the literature are that more work needs to be done on degradation kinetics and reactor modeling of the combined process, and also dynamics of the initial attack on primary contaminants and intermediate species generation. Furthermore, better economic models must be developed to estimate how the cost of this combined process varies with specific industrial wastewater characteristics, the overall decontamination efficiency and the relative cost of the AOP versus biological treatment. PMID:20956012

  3. Combination of Advanced Oxidation Processes and biological treatments for wastewater decontamination-A review

    International Nuclear Information System (INIS)

    Nowadays there is a continuously increasing worldwide concern for development of alternative water reuse technologies, mainly focused on agriculture and industry. In this context, Advanced Oxidation Processes (AOPs) are considered a highly competitive water treatment technology for the removal of those organic pollutants not treatable by conventional techniques due to their high chemical stability and/or low biodegradability. Although chemical oxidation for complete mineralization is usually expensive, its combination with a biological treatment is widely reported to reduce operating costs. This paper reviews recent research combining AOPs (as a pre-treatment or post-treatment stage) and bioremediation technologies for the decontamination of a wide range of synthetic and real industrial wastewater. Special emphasis is also placed on recent studies and large-scale combination schemes developed in Mediterranean countries for non-biodegradable wastewater treatment and reuse. The main conclusions arrived at from the overall assessment of the literature are that more work needs to be done on degradation kinetics and reactor modeling of the combined process, and also dynamics of the initial attack on primary contaminants and intermediate species generation. Furthermore, better economic models must be developed to estimate how the cost of this combined process varies with specific industrial wastewater characteristics, the overall decontamination efficiency and the relative cost of the AOP versus biological treatment.

  4. Advanced oxidation processes for wastewater treatment using a plasma/ozone combination system

    Science.gov (United States)

    Takeuchi, Nozomi; Kamiya, Yu; Saeki, Ryo; Tachibana, Kosuke; Yasuoka, Koichi

    2014-10-01

    Advanced oxidation process (AOP) using OH radicals is a promising method for the decomposition of persistent organic compounds in wastewater. Although many types of plasma reactors have been developed for the AOP, they are unsuitable for the complete decomposition of highly concentrated organic compounds. The reason for the incomplete decomposition is that OH radicals, particularly at a high density, recombine among themselves to form hydrogen peroxide. We have developed a combination plasma reactor in which ozone gas is fed, so that the generated hydrogen peroxide is re-converted to OH radicals. Pulsed plasmas generated within oxygen bubbles supply not only OH radicals but also hydrogen peroxide into wastewater. The total organic carbon (TOC) of the wastewater was more than 1 gTOC/L. The TOC values decreased linearly with time, and the persistent compounds which could not be decomposed by ozone were completely mineralized within 8 h of operation.

  5. Chemical and toxicological evaluation of transformation products during advanced oxidation processes.

    Science.gov (United States)

    vom Eyser, C; Börgers, A; Richard, J; Dopp, E; Janzen, N; Bester, K; Tuerk, J

    2013-01-01

    The entry of pharmaceuticals into the water cycle from sewage treatment plants is of growing concern because environmental effects are evident at trace levels. Ozonation, UV- and UV/H(2)O(2)-treatment were tested as an additional step in waste water treatment because they have been proven to be effective in eliminating aqueous organic contaminants. The pharmaceuticals carbamazepine, ciprofloxacin, diclofenac, metoprolol and sulfamethoxazole as well as the personal care products galaxolide and tonalide were investigated in terms of degradation efficiency and by-product formation in consideration of toxic effects. The substances were largely removed from treatment plant effluent by ozonation, UV- and UV/H(2)O(2)-treatment. Transformation products were detected in all tested treatment processes. Accompanying analysis showed no genotoxic, cytotoxic or estrogenic potential for the investigated compounds after oxidative treatment of real waste waters. The results indicate that by-product formation from ozonation and advanced oxidation processes does not have any negative environmental impact. PMID:24225097

  6. Combined advanced oxidation and biological treatment processes for the removal of pesticides from aqueous solutions

    International Nuclear Information System (INIS)

    Advanced oxidation processes were combined with biological treatment processes in this study to remove both pesticides and then the COD load from aqueous solutions. It was found that O3 and O3/UV oxidation systems were able to reach 90 and 100%, removal of the pesticide Deltamethrin, respectively, in a period of 210 min. The use of O3 combined with UV radiation enhances pesticides degradation and the residual pesticide reaches zero in the case of Deltamethrin. The combined O3/UV system can reduce COD up to 20% if the pH of the solution is above 4. Both pesticide degradation and COD removal in the combined O3/UV system follow the pseudo-first-order kinetics and the parameters of this model were evaluated. The application of the biological treatment to remove the bulk COD from different types of feed solution was investigated. More than 95% COD removal was achieved when treated wastewater by the O3/UV system was fed to the bioreactor. The parameters of the proposed Grau model were estimated

  7. Decolorization of kraft bleaching effluent by advanced oxidation processes using copper (II) as electron acceptor.

    Science.gov (United States)

    Yeber, María C; Oñate, Katherine P; Vidal, Gladys

    2007-04-01

    Two advanced oxidation processes (AOPs), TiO2/UV/O2 and TiO2/UV/Cu (II), were used to remove color from a Kraft bleaching effluent. The optimal decoloration rate was determined by multivariate analysis, obtaining a mathematical model to evaluate the effect among variables. TiO2 and Cu (II) concentrations and the reaction times were optimized. The experimental design resulted in a quadratic matrix of 30 experiments. Additionally, the pH influence on the color removal was determined by multivariate analysis. Results indicate that color removal was 94% at acidic pH (3.0) in the presence of Cu (11) as an electron acceptor. Under this condition, the biodegradation of the effluent increased from 0.3 to 0.6. Moreover, 70% of COD (chemical oxygen demand) was removed, and the ecotoxicity, measured by Daphnia magna, was reduced. Photocatalytic oxidation to remove the color contained in the Kraft mill bleaching effluent was effective under the following conditions: short reaction time, acidic pH values, and without the addition of oxygen due to the presence of Cu (II) in the effluent. Moreover, residual Cu (II) was a minimum (0.05.mg L(-1)) and was not toxic to the next biological stage. The experimental design methodology indicated that a quadratic polynomial model may be used to representthe efficiencyfor degradation of the Kraft bleach pulp effluent by a photocatalytic process. PMID:17438808

  8. Optimization of stabilized leachate treatment using ozone/persulfate in the advanced oxidation process

    International Nuclear Information System (INIS)

    Highlights: ► Ozone and persulfate reagent (O3/S2O82-) was used to treat stabilized leachate. ► Central composite design (CCD) with response surface methodology (RSM) was applied. ► Operating variables including ozone and persulfate dosage, pH variance, and reaction time. ► Optimum removal of COD, color, and NH3–N was 72%, 96%, and 76%, respectively. ► A good value of ozone consumption (OC) obtained with 0.60 (kg O3/kg COD). - Abstract: The objective of this study was to investigate the performance of employing persulfate reagent in the advanced oxidation of ozone to treat stabilized landfill leachate in an ozone reactor. A central composite design (CCD) with response surface methodology (RSM) was applied to evaluate the relationships between operating variables, such as ozone and persulfate dosages, pH, and reaction time, to identify the optimum operating conditions. Quadratic models for the following four responses proved to be significant with very low probabilities (3–N, and ozone consumption (OC). The obtained optimum conditions included a reaction time of 210 min, 30 g/m3 ozone, 1 g/1 g COD0/S2O82- ratio, and pH 10. The experimental results were corresponded well with predicted models (COD, color, and NH3–N removal rates of 72%, 96%, and 76%, respectively, and 0.60 (kg O3/kg COD OC). The results obtained in the stabilized leachate treatment were compared with those from other treatment processes, such as ozone only and persulfate S2O82- only, to evaluate its effectiveness. The combined method (i.e., O3/S2O82-) achieved higher removal efficiencies for COD, color, and NH3–N compared with other studied applications. Furthermore, the new method is more efficient than ozone/Fenton in advanced oxidation process in the treatment of the same studied leachate

  9. Advanced oxidation processes: a review of fundamentals and applications in the treatment of urban and industrial wastewaters

    OpenAIRE

    Karla Santos de Araújo1;; Raissa Antonelli2;; Beatriz Gaydeczka; Ana Claudia Granato2;; Geoffroy Roger Pointer Malpass

    2016-01-01

    Contamination of water by toxic and/or recalcitrant species has great environmental impacts. In this context, Advanced Oxidation Processes (AOPs) - technologies that principally use the hydroxyl radical (HO●) for oxidation - have emerged as promising alternatives in treating urban and industrial wastewaters. This study reviewed the literature on POAs and presented data regarding the efficiency of these processes in pollutant degradation, comparing the theoretical reasoning and its industrial ...

  10. Degradation of triketone herbicides, mesotrione and sulcotrione, using advanced oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Jović, Milica, E-mail: milica_jovic@chem.bg.ac.rs [Innovation Center of the Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Manojlović, Dragan [Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Stanković, Dalibor [Innovation Center of the Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Dojčinović, Biljana [Center of Chemistry, Institute of Chemistry, Technology and Metallurgy, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Obradović, Bratislav [Faculty of Physics, University of Belgrade, Cara Dušana 13, 11000 Belgrade (Serbia); Gašić, Uroš; Roglić, Goran [Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia)

    2013-09-15

    Highlights: • Thirteen products are identified during all degradations for both pesticides. • In all degradations same products and mechanism was observed for both pesticides. • Dominant mechanism for all degradations starts with attack on the carbonyl group. • Only in ozone and DBD degradation one product is formed in radical reaction. • Only in Fenton degradation opening of benzene ring occurs. -- Abstract: Degradation of two triketone herbicides, mesotrione and sulcotrione, was studied using four different advanced oxidation processes (AOPs): ozonization, dielectric barrier discharge (DBD reactor), photocatalysis and Fenton reagent, in order to find differences in mechanism of degradation. Degradation products were identified by high performance liquid chromatography (HPLC–DAD) and UHPLC–Orbitrap–MS analyses. A simple mechanism of degradation for different AOP was proposed. Thirteen products were identified during all degradations for both pesticides. It was assumed that the oxidation mechanisms in the all four technologies were not based only on the production and use of the hydroxyl radical, but they also included other kinds of oxidation mechanisms specific for each technology. Similarity was observed between degradation mechanism of ozonation and DBD. The greatest difference in the products was found in Fenton degradation which included the opening of benzene ring. When degraded with same AOP pesticides gave at the end of treatment the same products. Global toxicity and COD value of samples was determined after all degradations. Real water sample was used to study influence of organic matter on pesticide degradation. These results could lead to accurate estimates of the overall effects of triketone herbicides on environmental ecosystems and also contributed to the development of improved removal processes.

  11. Degradation of triketone herbicides, mesotrione and sulcotrione, using advanced oxidation processes

    International Nuclear Information System (INIS)

    Highlights: • Thirteen products are identified during all degradations for both pesticides. • In all degradations same products and mechanism was observed for both pesticides. • Dominant mechanism for all degradations starts with attack on the carbonyl group. • Only in ozone and DBD degradation one product is formed in radical reaction. • Only in Fenton degradation opening of benzene ring occurs. -- Abstract: Degradation of two triketone herbicides, mesotrione and sulcotrione, was studied using four different advanced oxidation processes (AOPs): ozonization, dielectric barrier discharge (DBD reactor), photocatalysis and Fenton reagent, in order to find differences in mechanism of degradation. Degradation products were identified by high performance liquid chromatography (HPLC–DAD) and UHPLC–Orbitrap–MS analyses. A simple mechanism of degradation for different AOP was proposed. Thirteen products were identified during all degradations for both pesticides. It was assumed that the oxidation mechanisms in the all four technologies were not based only on the production and use of the hydroxyl radical, but they also included other kinds of oxidation mechanisms specific for each technology. Similarity was observed between degradation mechanism of ozonation and DBD. The greatest difference in the products was found in Fenton degradation which included the opening of benzene ring. When degraded with same AOP pesticides gave at the end of treatment the same products. Global toxicity and COD value of samples was determined after all degradations. Real water sample was used to study influence of organic matter on pesticide degradation. These results could lead to accurate estimates of the overall effects of triketone herbicides on environmental ecosystems and also contributed to the development of improved removal processes

  12. Bioassays as a tool for evaluating advanced oxidation processes in water and wastewater treatment.

    Science.gov (United States)

    Rizzo, Luigi

    2011-10-01

    Advanced oxidation processes (AOPs) have been widely used in water and wastewater treatment for the removal of organic and inorganic contaminants as well as to improve biodegradability of industrial wastewater. Unfortunately, the partial oxidation of organic contaminants may result in the formation of intermediates more toxic than parent compounds. In order to avoid this drawback, AOPs are expected to be carefully operated and monitored, and toxicity tests have been used to evaluate whether effluent detoxification takes place. In the present work, the effect of AOPs on the toxicity of aqueous solutions of different classes of contaminants as well as actual aqueous matrices are critically reviewed. The dualism toxicity-biodegradability when AOPs are used as pre-treatment step to improve industrial wastewater biodegradability is also discussed. The main conclusions/remarks include the followings: (i) bioassays are a really useful tool to evaluate the dangerousness of AOPs as well as to set up the proper operative conditions, (ii) target organisms for bioassays should be chosen according to the final use of the treated water matrix, (iii) acute toxicity tests may be not suitable to evaluate toxicity in the presence of low/realistic concentrations of target contaminants, so studies on chronic effects should be further developed, (iv) some toxicity tests may be not useful to evaluate biodegradability potential, in this case more suitable tests should be applied (e.g., activated sludge bioassays, respirometry). PMID:21722938

  13. Comparison of various advanced oxidation processes for the degradation of phenylurea herbicides.

    Science.gov (United States)

    Kovács, Krisztina; Farkas, János; Veréb, Gábor; Arany, Eszter; Simon, Gergő; Schrantz, Krisztina; Dombi, András; Hernádi, Klára; Alapi, Tünde

    2016-01-01

    Various types of advanced oxidation processes (AOPs), such as UV photolysis, ozonation, heterogeneous photocatalysis and their combinations were comparatively examined at the same energy input in a home-made reactor. The oxidative transformations of the phenylurea herbicides fenuron, monuron and diuron were investigated. The initial rates of transformation demonstrated that UV photolysis was highly efficient in the cases of diuron and monuron. Ozonation proved to be much more effective in the transformation of fenuron than in those of the chlorine containing monuron and diuron. In heterogeneous photocatalysis, the rate of decomposition decreased with increase of the number of chlorine atoms in the target molecule. Addition of ozone to UV-irradiated solutions and/or TiO2-containing suspensions markedly increased the initial rates of degradation. Dehalogenation of monuron and diuron showed that each of these procedures is suitable for the simultaneous removal of chlorinated pesticides and their chlorinated intermediates. Heterogeneous photocatalysis was found to be effective in the mineralization. PMID:26764571

  14. Degradation of the fluoroquinolone enrofloxacin by electrochemical advanced oxidation processes based on hydrogen peroxide electrogeneration

    International Nuclear Information System (INIS)

    Solutions of the veterinary fluoroquinolone antibiotic enrofloxacin in 0.05 M Na2SO4 of pH 3.0 have been comparatively degraded by electrochemical advanced oxidation processes such as anodic oxidation with electrogenerated H2O2 (AO-H2O2), electro-Fenton (EF), photoelectro-Fenton (PEF) and solar photoelectro-Fenton (SPEF) at constant current density. The study has been performed using an undivided stirred tank reactor of 100 ml and a batch recirculation flow plant of 2.5 l with an undivided filter-press cell coupled to a solar photoreactor, both equipped with a Pt or boron-doped diamond (BDD) anode and a carbon-polytetrafluoroethylene gas diffusion cathode to generate H2O2 from O2 reduction. In EF, PEF and SPEF, hydroxyl radical (·OH) is formed from Fenton's reaction between added catalytic Fe2+ and generated H2O2. Almost total decontamination of enrofloxacin solutions is achieved in the stirred tank reactor by SPEF with BDD. The use of the batch recirculation flow plant showed that this process is the most efficient and can be viable for industrial application, becoming more economic and yielding higher mineralization degree with raising antibiotic content. This is feasible because organics are quickly oxidized with ·OH formed from Fenton's reaction and at BDD from water oxidation, combined with the fast photolysis of complexes of Fe(III) with generated carboxylic acids under solar irradiation. The lower intensity of UVA irradiation used in PEF with BDD causes a slower degradation. EF with BDD is less efficient since ·OH cannot destroy the most persistent Fe(III)-oxalate and Fe(III)-oxamate complexes. AO-H2O2 with BDD yields the poorest mineralization because pollutants are only removed with ·OH generated at BDD. All procedures are less potent using Pt as anode due to the lower production of ·OH at its surface. Enrofloxacin decay always follows a pseudo first-order reaction. Its primary aromatic by-products and short intermediates including polyols, ketones

  15. Degradation of the fluoroquinolone enrofloxacin by electrochemical advanced oxidation processes based on hydrogen peroxide electrogeneration

    Energy Technology Data Exchange (ETDEWEB)

    Guinea, Elena; Garrido, Jose Antonio; Rodriguez, Rosa Maria; Cabot, Pere-Lluis; Arias, Conchita; Centellas, Francesc [Laboratori d' Electroquimica dels Materials i del Medi Ambient, Departament de Quimica Fisica, Facultat de Quimica, Universitat de Barcelona, Marti i Franques 1-11, 08028 Barcelona (Spain); Brillas, Enric, E-mail: brillas@ub.ed [Laboratori d' Electroquimica dels Materials i del Medi Ambient, Departament de Quimica Fisica, Facultat de Quimica, Universitat de Barcelona, Marti i Franques 1-11, 08028 Barcelona (Spain)

    2010-02-15

    Solutions of the veterinary fluoroquinolone antibiotic enrofloxacin in 0.05 M Na{sub 2}SO{sub 4} of pH 3.0 have been comparatively degraded by electrochemical advanced oxidation processes such as anodic oxidation with electrogenerated H{sub 2}O{sub 2} (AO-H{sub 2}O{sub 2}), electro-Fenton (EF), photoelectro-Fenton (PEF) and solar photoelectro-Fenton (SPEF) at constant current density. The study has been performed using an undivided stirred tank reactor of 100 ml and a batch recirculation flow plant of 2.5 l with an undivided filter-press cell coupled to a solar photoreactor, both equipped with a Pt or boron-doped diamond (BDD) anode and a carbon-polytetrafluoroethylene gas diffusion cathode to generate H{sub 2}O{sub 2} from O{sub 2} reduction. In EF, PEF and SPEF, hydroxyl radical (centre dotOH) is formed from Fenton's reaction between added catalytic Fe{sup 2+} and generated H{sub 2}O{sub 2}. Almost total decontamination of enrofloxacin solutions is achieved in the stirred tank reactor by SPEF with BDD. The use of the batch recirculation flow plant showed that this process is the most efficient and can be viable for industrial application, becoming more economic and yielding higher mineralization degree with raising antibiotic content. This is feasible because organics are quickly oxidized with centre dotOH formed from Fenton's reaction and at BDD from water oxidation, combined with the fast photolysis of complexes of Fe(III) with generated carboxylic acids under solar irradiation. The lower intensity of UVA irradiation used in PEF with BDD causes a slower degradation. EF with BDD is less efficient since centre dotOH cannot destroy the most persistent Fe(III)-oxalate and Fe(III)-oxamate complexes. AO-H{sub 2}O{sub 2} with BDD yields the poorest mineralization because pollutants are only removed with centre dotOH generated at BDD. All procedures are less potent using Pt as anode due to the lower production of centre dotOH at its surface. Enrofloxacin

  16. Applicability of fluidized bed reactor in recalcitrant compound degradation through advanced oxidation processes: a review.

    Science.gov (United States)

    Tisa, Farhana; Abdul Raman, Abdul Aziz; Wan Daud, Wan Mohd Ashri

    2014-12-15

    Treatment of industrial waste water (e.g. textile waste water, phenol waste water, pharmaceutical etc) faces limitation in conventional treatment procedures. Advanced oxidation processes (AOPs) do not suffer from the limits of conventional treatment processes and consequently degrade toxic pollutants more efficiently. Complexity is faced in eradicating the restrictions of AOPs such as sludge formation, toxic intermediates formation and high requirement for oxidants. Increased mass-transfer in AOPs is an alternate solution to this problem. AOPs combined with Fluidized bed reactor (FBR) can be a potential choice compared to fixed bed or moving bed reactor, as AOP catalysts life-span last for only maximum of 5-10 cycles. Hence, FBR-AOPs require lesser operational and maintenance cost by reducing material resources. The time required for AOP can be minimized using FBR and also treatable working volume can be increased. FBR-AOP can process from 1 to 10 L of volume which is 10 times more than simple batch reaction. The mass transfer is higher thus the reaction time is lesser. For having increased mass transfer sludge production can be successfully avoided. The review study suggests that, optimum particle size, catalyst to reactor volume ratio, catalyst diameter and liquid or gas velocity is required for efficient FBR-AOP systems. However, FBR-AOPs are still under lab-scale investigation and for industrial application cost study is needed. Cost of FBR-AOPs highly depends on energy density needed and the mechanism of degradation of the pollutant. The cost of waste water treatment containing azo dyes was found to be US$ 50 to US$ 500 per 1000 gallons where, the cost for treating phenol water was US$ 50 to US$ 800 per 1000 gallons. The analysis for FBR-AOP costs has been found to depend on the targeted pollutant, degradation mechanism (zero order, 1st order and 2nd order) and energy consumptions by the AOPs. PMID:25190594

  17. Degradation of benzalkonium chloride coupling photochemical advanced oxidation technologies with biological processes

    International Nuclear Information System (INIS)

    The combination of Advanced Oxidation Technologies (AOTs) and biological processes can be visualized as a very successful technological option for treatment of effluents, because it combines high oxidizing technologies with a conventional, low-cost and well-established treatment technology.Photochemical AOTs, like UV-C with or without H2O2, photo-Fenton (PF, UV/H2O2/Fe(II-III)) and UV/TiO2 heterogeneous photo catalysis involve the generation and use of powerful oxidizing species, mainly the hydroxyl radical.In almost all AOTs, it is possible to use sunlight. Benzalkonium chloride (dodecyldimetylbencylammonium chloride, BKC) is a widely used surfactant, which has many industrial applications.Due to its antibacterial effect, it cannot be eliminated from effluents by a biological treatment, and the complexity of its chemical structure makes necessary the use of drastic oxidizing treatments to achieve complete mineralization and to avoid the formation of byproducts even more toxic than the initial compound.In this study, different alternatives for BKC treatment using photochemical AOTs followed by bio catalytic techniques are presented.Three AOTs were tested: a) UV-C (254 nm, germicide lamp) with and without H2O2, b) PF (366 nm), c) UV/TiO2 (254 and 366 nm). PF at a 15:1:1 H2O2total/BKC0/Fe0 molar ratio at 55 degree C was the most efficient treatment in order to decrease the tensioactivity and the total organic carbon of the solution . The biocatalysis was studied in a reactor fitted with a biofilm of microorganisms coming from a sludge-water treatment plant. To evaluate the maximal BKC concentration that could be allowed to ingress to the biological reactor after the AOT treatment, the toxicity of solutions of different BKC concentrations was analyzed. The study of the relevant parameters of both processes and their combination allowed to establish the preliminary conditions for optimizing the pollutant degradation

  18. Conventional and advanced oxidation processes used in disinfection of treated urban wastewater.

    Science.gov (United States)

    Rodríguez-Chueca, J; Ormad, M P; Mosteo, R; Sarasa, J; Ovelleiro, J L

    2015-03-01

    The purpose of the current study is to compare the inactivation of Escherichia coli in wastewater effluents using conventional treatments (chlorination) and advanced oxidation processes (AOPs) such as UV irradiation, hydrogen peroxide (H2O2)/solar irradiation, and photo-Fenton processes. In addition, an analysis of the operational costs of each treatment is carried out taking into account the optimal dosages of chemicals used. Total inactivation of bacteria (7.5 log) was achieved by means of chlorination and UV irradiation. However, bacterial regrowth was observed 6 hours after the completion of UV treatment, obtaining a disinfection value around 3 to 4 log. On the other hand, the combination H2O2/solar irradiation achieved a maximum inactivation of E. coli of 3.30 ± 0.35 log. The photo-Fenton reaction achieved a level of inactivation of 4.87 ± 0.10 log. The order of disinfection, taking into account the reagent/cost ratio of each treatment, is as follows: chlorination > UV irradiation > photo-Fenton > H2O2/sunlight irradiation. PMID:25842540

  19. Toxicology Aspects of the Decomposition of Diuron by advanced Oxidation Processes

    Directory of Open Access Journals (Sweden)

    Alapi Tünde

    2015-06-01

    Full Text Available Diuron is a phenylurea-based residual herbicide with toxic and endocrine disrupting effects. The aims of the present work were the comparison of the efficiency of various advanced oxidation processes, such as direct ultraviolet photolysis, ozonation, their combination, and heterogeneous photocatalysis from the point of view of the transformation rate of diuron, rate of mineralisation and dehalogenation, formation of aromatic intermediates, and ecotoxicological effects of the formed multicomponent solutions during the treatments. The initial rates of transformation of diuron are in the order of ozonation < heterogeneous photocatalysis < UV photolysis < combination of UV photolysis and ozonation. Each method provided similar tendencies in the decrease of the concentration of organically bound chlorines (AOX since, until the diuron was completely degraded, the concentration of AOX decreased almost to zero in each case. However, only heterogeneous photocatalysis was found to be effective in terms of mineralisation. Ecotoxicological results showed that in each case, except for ozonation, the toxicity of the treated solutions changed through a maximum during the transformation of diuron. The maximum value was found to be lower in the case of heterogeneous photocatalysis. Thus, the formation and decomposition of by-products of relatively higher toxicity than diuron can be supposed. Our results confirmed that the amount of the formed (aromatic intermediates, their quality and specific toxicity strongly depend on the applied processes.

  20. Surface treatment of NiTi shape memory alloy by modified advanced oxidation process

    Institute of Scientific and Technical Information of China (English)

    CHU Cheng-lin; WANG Ru-meng; YIN Li-hong; PU Yue-pu; DONG Yin-sheng; GUO Chao; SHENG Xiao-bo; LIN Ping-hua; CHU Paul-K

    2009-01-01

    A modified advanced oxidation process(AOP) utilizing a UV/electrochemically-generated peroxide system was used to fabricate titania films on chemically polished NiTi shape memory alloy(SMA). The microstructure and biomedical properties of the film were characterized by scanning electron microscopy(SEM), X-ray photoelectron spectroscopy(XPS), inductively-coupled plasma mass spectrometry(ICPMS), hemolysis analysis, and blood platelet adhesion test. It is found that the modified AOP has a high processing effectiveness and can result in the formation of a dense titania film with a Ni-free zone near its top surface. In comparison, Ni can still be detected on the outer NiTi surface by the conventional AOP using the UV/H2O2 system. The depth profiles of O, Ni, Ti show that the film possesses a smooth graded interface structure next to the NiTi substrate and this structure enhances the mechanical stability of titania film. The titania film can dramatically reduce toxic Ni ion release and also improve the hemolysis resistance and thromboresistance of biomedical NiTi SMA.

  1. Incorporating biodegradation and advanced oxidation processes in the treatment of spent metalworking fluids.

    Science.gov (United States)

    MacAdam, Jitka; Ozgencil, Haci; Autin, Olivier; Pidou, Marc; Temple, Clive; Parsons, Simon; Jefferson, Bruce

    2012-12-01

    The treatment of spent metalworking fluids (MWFs) is difficult due to their complex and variable composition. Small businesses often struggle to meet increasingly stringent legislation and rising costs as they need to treat this wastewater on site annually over a short period. Larger businesses that treat their wastewater continuously can benefit from the use of biological processes, although new MWFs designed to resist biological activity represent a challenge. A three-stage treatment is generally applied, with the oil phase being removed first, followed by a reduction in COD loading and then polishing of the effluent's quality in the final stage. The performance of advanced oxidation processes (AOPs), which could be of benefit to both types of businesses was studied. After assessing the biodegradability of spent MFW, different AOPs were used (UV/H2O2, photo-Fenton and UV/TiO2) to establish the treatability of this wastewater by hydroxyl radicals (*OH). The interactions of both the chemical and biological treatments were also investigated. The wastewater was found to be readily biodegradable in the Zahn-Wellens test with 69% COD and 74% DOC removal. The UV/TiO2 reactor was found to be the cheapest option achieving a very good COD removal (82% at 20 min retention time and 10 L min(-1) aeration rate). The photo-Fenton process was found to be efficient in terms of degradation rate, achieving 84% COD removal (1 M Fe2+, 40 M H2O2, 20.7 J cm(-2), pH 3) and also improving the wastewater's biodegradability. The UV/H202 process was the most effective in removing recalcitrant COD in the post-biological treatment stage. PMID:23437675

  2. ADVANCED OXIDATION PROCESSES (AOPS) FOR DESTRUCTION OF METHYL TERTIARY BUTYL ETHER (MTBE -AN UNREGULATED CONTAMINANT) IN DRINKING WATER

    Science.gov (United States)

    Advanced oxidation processes (AOPs) provide a promising treatment option for the destruction of MTBE directly in surface and ground waters. An ongoing study is evaluating the ability of three AOPs; hydrogen peroxide/ozone (H2O2/ O3), ultraviolet irradiation/ozone (UV/O3) and ultr...

  3. Development of advanced spent fuel management process. The fabrication and oxidation behavior of simulated metallized spent fuel

    International Nuclear Information System (INIS)

    The simulated metallized spent fuel ingots were fabricated and evaluated the oxidation rates and the activation energies under several temperature conditions to develop an advanced spent fuel management process. It was also checked the alloying characteristics of the some elements with metal uranium. (Author). 3 refs., 1 tab., 36 figs

  4. Effect of advanced oxidation processes (AOPs) on the biodegradability of municipal wastewater for its reuse in the textile industry

    OpenAIRE

    Jarni, Klara; Kompare, Boris; Drev, Darko; Griessler Bulc, Tjaša; Krivograd-Klemenčič, Aleksandra

    2013-01-01

    Reuse of treated municipal wastewater to supplement part of fresh water is becoming more and more important. However, treated water can contain some pollutants that cannot be successfully removed with classical biological wastewater treatment processes. Aim of the study presented was to assess whether advanced oxidation processes (AOPs) and special enzymes enhance biodegradation of municipal wastewater and if treated municipal wastewater can be reused in the production process of ...

  5. Pilot-scale treatment of olive oil mill wastewater by physicochemical and advanced oxidation processes.

    Science.gov (United States)

    Kiliç, M Yalili; Yonar, T; Kestioğlu, K

    2013-01-01

    The pilot-scale treatability of olive oil mill wastewater (OOMW) by physicochemical methods, ultrafiltration and advanced oxidation processes (AOPs) was investigated. Physicochemical methods (acid cracking, oil separation and coagulation-flocculation) showed high efficiency of chemical oxygen demand (COD) (85%), oil and grease (O&G) (> 97%), suspended solids (SS) (> 99%) and phenol (92%) removal from the OOMW. Ultrafiltration followed by physicochemical methods is effective in reducing the SS, O&G. The final permeate quality is found to be excellent with over 90% improvements in the COD and phenol parameters. AOPs (ozonation at a high pH, O3/UV, H2O2/UV, and O3/H2O2/UV) increased the removal efficiency and the O3/H2O2/UV combination among other AOPs studied in this paper was found to give the best results (> 99% removal for COD, > 99% removal for phenol and > 99% removal for total organic carbon). Pilot-scale treatment plant has been continuously operated on site for three years (3 months olive oil production campaign period of each year). The capital and operating costs of the applied treatment alternatives were also determined at the end of these seasons. The results obtained in this study have been patented for 7 years by the Turkish Patent Institute. PMID:24191487

  6. Response surface methodology for ozonation of trifluralin using advanced oxidation processes in an airlift photoreactor

    Science.gov (United States)

    Behin, J.; Farhadian, N.

    2016-06-01

    Degradation of trifluralin, as a wide used pesticide, was investigated by advance oxidation process comprising O3/UV/H2O2 in a concentric tube airlift photoreactor. Main and interactive effects of three independent factors including pH (5-9), superficial gas velocity (0.05-0.15 cm/s) and time (20-60 min) on the removal efficiency were assessed using central composite face-centered design and response surface method (RSM). The RSM allows to solve multivariable equations and to estimate simultaneously the relative importance of several contributing parameters even in the presence of complex interaction. Airlift photoreactor imposed a synergistic effect combining good mixing intensity merit with high ozone transfer rate. Mixing in the airlift photoreactor enhanced the UV light usage efficiency and its availability. Complete degradation of trifluralin was achieved under optimum conditions of pH 9 and superficial gas velocity 0.15 cm/s after 60 min of reaction time. Under these conditions, degradation of trifluralin was performed in a bubble column photoreactor of similar volume and a lower efficiency was observed.

  7. Reaction kinetics of selected micropollutants in ozonation and advanced oxidation processes.

    Science.gov (United States)

    Jin, Xiaohui; Peldszus, Sigrid; Huck, Peter M

    2012-12-01

    Second-order reaction rate constants of micropollutants with ozone (k(O3)) and hydroxyl radicals (k(OH)) are essential for evaluating their removal efficiencies from water during ozonation and advanced oxidation processes. Kinetic data are unavailable for many of the emerging micropollutants. Twenty-four micropollutants with very diverse structures and applications including endocrine disrupting compounds, pharmaceuticals, and personal care products were selected, and their k(O3) and k(OH) values were determined using bench-scale reactors (at pH 7 and T = 20 °C). Reactions with molecular ozone are highly selective as indicated by their k(O3) values ranging from 10(-2)-10(7) M(-1) s(-1). The general trend of ozone reactivity can be explained by micropollutant structures in conjunction with the electrophilic nature of ozone reactions. All of the studied compounds are highly reactive with hydroxyl radicals as shown by their high k(OH) values (10(8)-10(10) M(-1) s(-1)) even though they are structurally very diverse. For compounds with a low reactivity toward ozone, hydroxyl radical based treatment such as O(3)/H(2)O(2) or UV/H(2)O(2) is a viable alternative. This study contributed to filling the data gap pertaining kinetic data of organic micropollutants while confirming results reported in the literature where available. PMID:23079129

  8. Comparison of different advanced oxidation process to reduce toxicity and mineralisation of tannery wastewater.

    Science.gov (United States)

    Schrank, S G; José, H J; Moreira, R F P M; Schröder, H Fr

    2004-01-01

    Many organic compounds contained in wastewater are resistant to conventional chemical and/or biological treatment. Because of this reason different degradation techniques are studied as an alternative to biological and classical physico-chemical processes. Advanced Oxidation Processes (AOPs) probably have developed to become the best options in the near future. AOP while making use of different reaction systems, are all characterised by the same chemical feature: production of OH radicals (*OH). The versatility of AOPs is also enhanced by the fact that they offer different possibilities for OH radical production, thus allowing them to conform to specific treatment requirements. The main problem with AOPs is their high cost. The application of solar technologies to these processes could help to diminish that problem by reducing the energy consumption required for generating UV radiation. In this work, different AOPs (O3, TiO2/UV, Fenton and H2O2/UV) were examined to treat tannery wastewater or as a pre-treatment step for improving the biodegradation of tannery wastewater, at different pH and dosage of the chemicals. Under certain circumstances retardation in biodegradation and/or an increase in toxicity may be observed within these treatment steps. Two different bioassays (Daphnia magna and Vibrio fischeri) have been used for testing the progress of toxicity during the treatment. In parallel other objectives were to analyse and identify organic compounds present in the untreated wastewater and arising degradation products in AOP treated wastewater samples. For this purpose substance specific techniques, e.g., gas chromatography-mass spectrometry (GC-MS) in positive electron impact (El(+)) mode and atmospheric pressure ionisation (API) in combination with flow injection analysis (FIA) or liquid chromatography-mass and tandem mass spectrometry (LC-MS or LC-MS-MS) were performed. PMID:15497865

  9. Review of photochemical reaction constants of organic micropollutants required for UV advanced oxidation processes in water.

    Science.gov (United States)

    Wols, B A; Hofman-Caris, C H M

    2012-06-01

    Emerging organic contaminants (pharmaceutical compounds, personal care products, pesticides, hormones, surfactants, fire retardants, fuel additives etc.) are increasingly found in water sources and therefore need to be controlled by water treatment technology. UV advanced oxidation technologies are often used as an effective barrier against organic contaminants. The combined operation of direct photolysis and reaction with hydroxyl radicals ensures good results for a wide range of contaminants. In this review, an overview is provided of the photochemical reaction parameters (quantum yield, molar absorption, OH radical reaction rate constant) of more than 100 organic micropollutants. These parameters allow for a prediction of organic contaminant removal by UV advanced oxidation systems. An example of contaminant degradation is elaborated for a simplified UV/H(2)O(2) system. PMID:22483836

  10. Transformation of polyfluorinated compounds in natural waters by advanced oxidation processes.

    Science.gov (United States)

    Anumol, Tarun; Dagnino, Sonia; Vandervort, Darcy R; Snyder, Shane A

    2016-02-01

    The presence of perfluorocarboxylic acids (PFCAs) in source and finished drinking waters is a concern with studies showing bioaccumulation and adverse toxicological effects in wildlife and potentially humans. Per/Polyfluoroalkyl substances (PFAS) such as fluorotelomer alcohols have been identified as precursors for PFCAs in biological pathways. In this study, we investigated the fate of 6:2 and 8:2 homologues of the fluorotelomer unsaturated carboxylic acids (FTUCAs) during advanced oxidation process (AOPs). Results showed 6:2 FTUCA and 8:2 FTUCA transformed into 6-C PFCA (PFHxA) and 8-C PFCA (PFOA) respectively with very little other PFCA formation for all AOPs. The degradation of 6:2 FTUCA and 8:2 FTUCA was greater in the GW compared to SW for the ozone processes but similar for UV/H2O2. The formation of n-C PFCA followed O3>O3/H2O2 at same dose and UV/H2O2 had much lower formation at the doses tested. Non-targeted analysis with the LC-MS-qTOF indicated the production of other PFCAs which contribute to the total mass balance, although no intermediate product was discovered indicating a rapid and direct transformation from the FTUCAs to the PFCAs and/or significant volatilization of intermediates. With the use of AOPs essential to water reuse treatment schemes, this work raises concerns over the risk of potential formation of PFCAs in the treatment and their adverse health effects in finished drinking water. PMID:26524147

  11. Enhancing hydrophilicity and water permeability of PET track-etched membranes by advanced oxidation process

    Science.gov (United States)

    Korolkov, Ilya V.; Mashentseva, Anastassiya A.; Güven, Olgun; Zdorovets, Maxim V.; Taltenov, Abzal A.

    2015-12-01

    In this study we present results on the application of advanced oxidation systems for effective and non-toxic oxidation of poly(ethylene terephthalate) track-etched membranes (PET TeMs) to improve their wettability and water transport properties. Two oxidizing systems: H2O2 under UV irradiation (H2O2/UV) and Fenton system under visible light (Fenton/H2O2/Vis) were compared. The surface of functionalized PET TeMs was characterized by using colorimetric assay, contact angle measurements and X-ray photoelectron spectroscopy (XPS). Results clearly showed that water permeability of PET TeMs treated with H2O2/UV was improved by 28 ± 5% compared with etched-only membrane, the same parameter was found to increase by 13 ± 4% in the case of Fenton/H2O2/Vis treatment. The proposed oxidation technique is very simple, environment friendly and not requiring special equipment or expensive chemicals. The surface hydrophilicity of the membranes stored for 360 days in air between paper sheets was analyzed by contact angle test, colorimetric assay to measure concentration of carboxylic groups on the surface with toluidine blue and XPS analysis. The hydrophilic properties of oxidized PET TeMs were found to be stable for a long period of time.

  12. Comparison Between the Efficiency of Advanced Oxidation Process and Coagulation for Removal Organophosphorus and Carbamat Pesticides

    Directory of Open Access Journals (Sweden)

    A.R Rahmani

    2011-10-01

    Full Text Available Background and Objectives: Water pollution by pesticides has adverse effects on the environment and human health, as well .In recent years, advanced oxidation processes, have been gone through to a very high degree for pesticides removal. Poly-Aluminum chloride (PAC used for water treatment, can be effective on pesticides removal. The aim of this research was to study the use of UV/O3 and PAC in the removal of pesticides from drinking water.Materials and Methods: In this descriptive- analytical survey, specific concentrations of pesticides (1,5,10,15,20 ppm;namely Diazinon, Chlorpyrifos, Carbaril were prepared through addition to deionized water. Dichloromethane was used for samples' extraction, samples extracted with Liquid- Liquid & Solid-phase extraction , finally entered bath reactor at pH (6,7,9 .The samples then exposed to UV/O3at contact time of (0.5,1,1.5 and 2 hours . In the PAC pilot , the effects of various concentrations of pesticides, and PAC - ranging (12/24 and 36 ppm were investigated for the efficacy of pesticides removal. All samples analyzed by GC/MS/MS and HPLC. Results: It was found that in UV/O3 reactor, with the rise of pH, decrease in pesticides concentration, and rise of contact time, the efficiency of removal increased too. In the PAC pilot, increase in PAC concentration and decrease in pesticides concentration , both increased the efficiency. Besides, both of the methods showed high efficiencies in the removal of both pesticides,i-e. halogenated Organophosphorus (Chlorpyrifos , non- halogenated Organophosphorus (Diazinon at the degree of over (%80 ; In case of carbamate pesticides (e.g. Carbaril efficiency was over (>%90. One-Way Anova & Two -Way Anova were used to analyze the obtained data.Conclusion: According these results these two methods are suggested for the removal of pesticides from aqueous solutions.

  13. Evaluation of copper slag to catalyze advanced oxidation processes for the removal of phenol in water

    Energy Technology Data Exchange (ETDEWEB)

    Huanosta-Gutierrez, T. [Instituto de Ingenieria, Coordinacion de Ingenieria Ambiental, Universidad Nacional Autonoma de Mexico, Cd. Universitaria, Coyoacan 04510, Mexico, D.F. (Mexico); Dantas, Renato F., E-mail: falcao@angel.qui.ub.es [Departament d' Enginyeria Quimica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); Ramirez-Zamora, R.M. [Instituto de Ingenieria, Coordinacion de Ingenieria Ambiental, Universidad Nacional Autonoma de Mexico, Cd. Universitaria, Coyoacan 04510, Mexico, D.F. (Mexico); Esplugas, S. [Departament d' Enginyeria Quimica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain)

    2012-04-30

    Highlights: Black-Right-Pointing-Pointer We evaluate the use of an industrial residue (copper slag) as catalyst in water treatment. Black-Right-Pointing-Pointer The copper slag was effective to remove organic pollutants (phenol) from water. Black-Right-Pointing-Pointer During experimentation, Cu and Fe leaching were not higher than the acceptable levels. Black-Right-Pointing-Pointer Slag/H{sub 2}O{sub 2}/UV and slag/H{sub 2}O{sub 2} treatments promoted biodegradability increment of the contaminated water. Black-Right-Pointing-Pointer The control of the reaction time would minimize the environmental impact of the produced effluents in terms of acute toxicity. - Abstract: The aim of this work was to evaluate the use of copper slag to catalyze phenol degradation in water by advanced oxidation processes (AOPs). Copper slag was tested in combination with H{sub 2}O{sub 2} (slag/H{sub 2}O{sub 2}) and H{sub 2}O{sub 2}/UV (slag/H{sub 2}O{sub 2}/UV). The studied methods promoted the complete photocatalytic degradation of phenol. Besides, they were able to reduce about 50% the TOC content in the samples. Slag/H{sub 2}O{sub 2}/UV and slag/H{sub 2}O{sub 2} treatments have favored biodegradability increment along the reaction time. Nevertheless, the irradiated method achieved higher values of the biodegradability indicator (BOD{sub 5}/TOC). The toxicity assessment indicated the formation of more toxic compounds in both treatments. However, the control of the reaction time would minimize the environmental impact of the effluents.

  14. Computerized pathway elucidation for hydroxyl radical-induced chain reaction mechanisms in aqueous phase advanced oxidation processes.

    Science.gov (United States)

    Li, Ke; Crittenden, John

    2009-04-15

    The radical reaction mechanism that is involved in advanced oxidation processes is complex. An increasing number of trace contaminants and stringent drinking water standards call for a rule-based model to provide insight to the mechanism of the processes. A model was developed to predict the pathway of contaminant degradation and byproduct formation during advanced oxidation. The model builds chemical molecules as graph objects, which enables mathematic abstraction of chemicals and preserves chemistry information. The model algorithm enumerates all possible reaction pathways according to the elementary reactions (built as reaction rules) established from experimental observation. The method can predict minor pathways that could lead to toxic byproducts so that measures can be taken to ensure drinking water treatment safety. The method can be of great assistance to water treatment engineers and chemists who appreciate the mechanism of treatment processes. PMID:19475958

  15. An Overview of the Integration of Advanced Oxidation Technologies And Other Processes For Water And Wastewater Treatment

    Directory of Open Access Journals (Sweden)

    Farhad Ein-Mozaffari

    2009-05-01

    Full Text Available Integration of advanced oxidation technologies and other traditional wastewater treatment processes has been proven to be more effective for treating polluted sources of drinking water and industrial wastewater economically. The way of selecting the methods depends on the characteristics of the waste stream, environmental regulations, and cost. Reviewing the experimental works on this area and discussing about their effectiveness as well as modeling of their works would be helpful for deciding whether the integrated process is effective to fulfill the annually restricted legislations with lower investment. Therefore, optimization of each process should be done based on different aspects such as operation time, operating cost, and energy consumption. In this review, recent achievements, developments and trends (2003-2009 on the integration of advanced oxidation technologies and other remediation methods have been studied.

  16. Advanced Wastewater Photo-oxidation System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Pioneer Astronautics proposes an advanced photocatalytic oxidation reactor for enhancing the reliability and performance of Water Recovery Post Processing systems...

  17. Comprehensive study on effects of water matrices on removal of pharmaceuticals by three different kinds of advanced oxidation processes.

    Science.gov (United States)

    Tokumura, Masahiro; Sugawara, Asato; Raknuzzaman, Mohammad; Habibullah-Al-Mamun, Md; Masunaga, Shigeki

    2016-09-01

    Simple semi-theoretical models were developed to estimate the performance of three different kinds of advanced oxidation processes (AOPs) in the degradation of pharmaceuticals. The AOPs included the photo-Fenton process as an example of a liquid-liquid reaction, the TiO2 photocatalytic oxidation process as a solid-liquid reaction, and the combined ozone and hydrogen peroxide oxidation process as a gas-liquid reaction; the effects of the aqueous matrices (CESs: co-existing substances) of actual wastewater on the removal of pharmaceuticals (carbamazepine and diclofenac) was taken into account. By comparing the characteristic parameters of the models, obtained from the experiments using pure water and actual wastewater, the effects of CESs on the respective removal mechanisms could be separately and quantitatively evaluated. As a general tendency, the AOPs proceeded less effectively (were inhibited) in the matrices containing CESs, as observed with the use of a lower initial concentration of pharmaceuticals. The inhibition mechanisms differed for the three types of AOPs. In the photo-Fenton process, the Fenton reaction was improved by the incorporation of CESs, while the photo-reduction reaction was significantly inhibited. In the TiO2 photocatalytic oxidation process, competition between the pharmaceuticals and CESs for adsorption on the catalyst surface was a less significant inhibitory factor than the scavenger effects of the CESs. The combined ozone and hydrogen peroxide oxidation process was most strongly inhibited by CESs among the AOPs investigated in this study. PMID:27317938

  18. Toxicity of coke wastewater treated with advanced oxidation by Fenton process supported by ultrasonic field

    OpenAIRE

    Kwarciak-Kozłowska Anna; Krzywicka Aleksandra

    2016-01-01

    The aim of the presented study was to determine the toxicity of wastewater from the production of coke. The wastewater was treated with advanced oxidation involving ultrasonic field with Fenton’s reagent (the amplitude was 61.5 μm and sonication time 8 min). Two doses of iron and four doses of hydrogen peroxide were used. The amount of hydrogen peroxide was proportional to the value of the chemical oxygen demand of raw wastewater, ranging from COD/H2O2 ratio of 1:2.5 to 1:20. Two tests were u...

  19. Novel MoSe2 hierarchical microspheres for applications in visible-light-driven advanced oxidation processes

    Science.gov (United States)

    Dai, Chu; Qing, Enping; Li, Yong; Zhou, Zhaoxin; Yang, Chao; Tian, Xike; Wang, Yanxin

    2015-11-01

    Advanced oxidation processes as a green technology have been adopted by combining the semiconductor catalyst MoSe2 with H2O2 under visible radiation. And novel three-dimensional self-assembled molybdenum diselenide (MoSe2) hierarchical microspheres from nanosheets were produced by using organic, selenium cyanoacetic acid sodium (NCSeCH2COONa) as the source of Se. The obtained products possess good crystallinity and present hierarchical structures with the average diameter of 1 μm. The band gap of MoSe2 microspheres is 1.68 eV and they present excellent photocatalytic activity under visible light irradiation in the MoSe2-H2O2 system. This effective photocatalytic mechanism was investigated in this study and can be attributed to visible-light-driven advanced oxidation processes.

  20. An Overview of the Integration of Advanced Oxidation Technologies And Other Processes For Water And Wastewater Treatment

    OpenAIRE

    Farhad Ein-Mozaffari; Masroor Mohajerani; Mehrab Mehrvar

    2009-01-01

    Integration of advanced oxidation technologies and other traditional wastewater treatment processes has been proven to be more effective for treating polluted sources of drinking water and industrial wastewater economically. The way of selecting the methods depends on the characteristics of the waste stream, environmental regulations, and cost. Reviewing the experimental works on this area and discussing about their effectiveness as well as modeling of their works would be helpful for decidin...

  1. Comparative study of the degradation of carbamazepine in water by advanced oxidation processes.

    Science.gov (United States)

    Dai, Chao-Meng; Zhou, Xue-Fei; Zhang, Ya-Lei; Duan, Yan-Ping; Qiang, Zhi-Min; Zhang, Tian C

    2012-06-01

    Degradation of carbamazepine (CBZ) using ultraviolet (UV), UV/H2O2, Fenton, UV/Fenton and photocatalytic oxidation with TiO2 (UV/TiO2) was studied in deionized water. The five different oxidation processes were compared for the removal kinetics of CBZ. The results showed that all the processes followed pseudo-first-order kinetics. The direct photolysis (UV alone) was found to be less effective than UV/H2O2 oxidation for the degradation of CBZ. An approximate 20% increase in the CBZ removal efficiency occurred with the UV/Fenton reaction as compared with the Fenton oxidation. In the UV/TiO2 system, the kinetics of CBZ degradation in the presence of different concentrations of TiO2 followed the pseudo-first order degradation, which was consistent with the Langmuir-Hinshelwood (L-H) model. On a time basis, the degradation efficiencies ofCBZ were in the following order: UV/Fenton (86.9% +/- 1.7%) > UV/TiO2 (70.4% +/- 4.2%) > Fenton (67.8% +/- 2.6%) > UV/H2O2 (40.65 +/- 5.1%) > UV (12.2% +/- 1.4%). However, the lowest cost was obtained with the Fenton process. PMID:22856279

  2. Treatment of mature landfill leachate by chemical precipitation and Fenton advanced oxidation process

    Directory of Open Access Journals (Sweden)

    Nemat Alah Jaafarzadeh Haghighi Fard

    2016-03-01

    Full Text Available Background: Mature landfill leachate is a complicated mixture which is resistant to biological treatment processes. The treatment of mature landfill leachate by struvite precipitation and Fenton oxidation was the main objective of the current research. Methods: Struvite with the phosphate/ammonia/magnesium molar ratio of 1/1/1.05 was considered during all experiments. Five initial pHs of 3, 4, 5, 6, and 7, four different H2O2/Fe mass ratios of 50, 100, 200, and 400, and reaction times of 20, 40, 80, 120, and 160 minutes were examined for the Fenton oxidation process. Results: A leachate sample with average chemical oxygen demand (COD, BOD5, and NH4 concentrations of 7350, 2220, and 2280 mg L-1, respectively, and a BOD5/COD ratio of 0.3 was introduced to the chemical precipitation unit. An NH4 removal efficiency of 87% was obtained at pH 8.5 for struvite precipitation. Under optimum conditions of Fenton oxidation, including pH 3, an H2O2/Fe2+ mass ratio of 200, and a reaction time of 160 min, more than 95% COD and BOD5 removal was observed. Conclusion: Struvite precipitation and Fenton oxidation are reliable and efficient alternatives for mature landfill treatment.

  3. Toxicity of coke wastewater treated with advanced oxidation by Fenton process supported by ultrasonic field

    Directory of Open Access Journals (Sweden)

    Kwarciak-Kozłowska Anna

    2016-03-01

    Full Text Available The aim of the presented study was to determine the toxicity of wastewater from the production of coke. The wastewater was treated with advanced oxidation involving ultrasonic field with Fenton’s reagent (the amplitude was 61.5 μm and sonication time 8 min. Two doses of iron and four doses of hydrogen peroxide were used. The amount of hydrogen peroxide was proportional to the value of the chemical oxygen demand of raw wastewater, ranging from COD/H2O2 ratio of 1:2.5 to 1:20. Two tests were used to determine the toxicity (algae growth inhibition test and Lepidium test. It was found that more toxic to algae was wastewater treated by Fenton’s reagent containing a higher dose of iron. A similar inhibitory effect was observed on the germination of cress seeds.

  4. 2-Chlorophenol Removal of Aqueous Solution Using Advanced Oxidation Processes Resulting from Iron/ Persulfate and Ultra Violet/ Persulfate

    Directory of Open Access Journals (Sweden)

    Shokufeh Astereki

    2016-06-01

    Full Text Available Background: Advanced oxidation processes are used to remove toxic aromatic compounds with low biodegradability, such as 2-chlorophenol. This study investigated the use of sulfate (SO4- and persulfate (S2O82- radicals, as one of the advanced oxidation methods, to remove 2- chlorophenol from aquatic solutions. Methods: This experimental and pilot-scale study was carried out using two chemical batch reactors; one of the reactors equipped with UV lamps and the other was on the hot plate. In iron/ persulfate (Fe/S2O82- and ultra violet/ persulfate (UV/S2O82- processes different parameters were investigated. Results: Iron, UV, the initial pH of the solution, persulfate concentration have considerable effects on the elimination of 2-chlorophenol in both processes. In both processes, the maximum elimination occurred in acidic conditions. The elimination efficiency was increased by increasing the concentration of 2-chlorophenol and UV intensity, and also by decreasing the concentration of persulfate and iron. Accordingly, in iron/ persulfate and ultra violet/ persulfate processes 2-chlorophenol was eliminated with 99.96% and 99.58% efficiencies, respectively. Conclusion: Sulfate radicals produced from activated persulfate ions with hot-Fe ion and UV radiation have significant impact on the removal of 2-chlorophenol. Therefore, the processes of Fe/S2O82- and UV/S2O82- can be regarded as good choices for industrial wastewater treatment plants operators in the future.

  5. Use of solar advanced oxidation processes for wastewater treatment: Follow-up on degradation products, acute toxicity, genotoxicity and estrogenicity.

    Science.gov (United States)

    Brienza, M; Mahdi Ahmed, M; Escande, A; Plantard, G; Scrano, L; Chiron, S; Bufo, S A; Goetz, V

    2016-04-01

    Wastewater tertiary treatment by advanced oxidation processes is thought to produce a treated effluent with lower toxicity than the initial influent. Here we performed tertiary treatment of a secondary effluent collected from a Waste Water Treatment Plant via homogeneous (solar/HSO5(-)/Fe(2+)) and heterogeneous (solar/TiO2) solar advanced oxidation aiming at the assessment of their effectiveness in terms of contaminants' and toxicity abatement in a plain solar reactor. A total of 53 organic contaminants were qualitatively identified by liquid chromatography coupled to high-resolution mass spectrometry after solid phase extraction. Solar advanced oxidation totally or partially removed the major part of contaminants detected within 4.5 h. Standard toxicity tests were performed using Vibrio fischeri, Daphnia magna, Pseudokirchneriella subcapitata and Brachionus calyciflorus organisms to evaluate acute and chronic toxicity in the secondary or tertiary effluents, and the EC50% was calculated. Estrogenic and genotoxic tests were carried out in an attempt to obtain an even sharper evaluation of potential hazardous effects due to micropollutants or their degradation by-products in wastewater. Genotoxic effects were not detected in effluent before or after treatment. However, we observed relevant estrogenic activity due to the high sensitivity of the HELN ERα cell line. PMID:26841289

  6. Treatment of mature landfill leachate by chemical precipitation and Fenton advanced oxidation process

    OpenAIRE

    Nemat Alah Jaafarzadeh Haghighi Fard; Sahand Jorfi; Mehdi Ahmadi; Samaneh Mirali; Raheleh Kujlu

    2016-01-01

    Background: Mature landfill leachate is a complicated mixture which is resistant to biological treatment processes. The treatment of mature landfill leachate by struvite precipitation and Fenton oxidation was the main objective of the current research. Methods: Struvite with the phosphate/ammonia/magnesium molar ratio of 1/1/1.05 was considered during all experiments. Five initial pHs of 3, 4, 5, 6, and 7, four different H2O2/Fe mass ratios of 50, 100, 200, and 400, and reaction times of ...

  7. Decolorization and mineralization of Allura Red AC aqueous solutions by electrochemical advanced oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Thiam, Abdoulaye; Sirés, Ignasi; Garrido, José A.; Rodríguez, Rosa M.; Brillas, Enric, E-mail: brillas@ub.edu

    2015-06-15

    Highlights: • Quicker degradation of Allura Red AC in the order EO-H{sub 2}O{sub 2} < EF < PEF with Pt or BDD anode. • Almost total mineralization achieved by the most powerful PEF process with BDD. • Similar decolorization and mineralization rate in SO{sub 4}{sup 2−}, ClO{sub 4}{sup −} and NO{sub 3}{sup −} media. • In Cl{sup −} medium, only slightly larger decolorization rate but strong inhibition of mineralization. • Identification of aromatic products, carboxylic acids and released NH{sub 4}{sup +}, NO{sub 3}{sup −} and SO{sub 4}{sup 2−} ions. - Abstract: The decolorization and mineralization of solutions containing 230 mg L{sup −1} of the food azo dye Allura Red AC at pH 3.0 have been studied upon treatment by electrochemical oxidation with electrogenerated H{sub 2}O{sub 2} (EO-H{sub 2}O{sub 2}), electro-Fenton (EF) and photoelectro-Fenton (PEF). Experiments were performed with a stirred tank reactor containing a boron-doped diamond (BDD) or Pt anode and an air-diffusion cathode to generate H{sub 2}O{sub 2}. The main oxidants were hydroxyl radicals formed at the anode surface from water oxidation and in the bulk from Fenton’s reaction between H{sub 2}O{sub 2} and added Fe{sup 2+}. The oxidation ability increased in the sequence EO-H{sub 2}O{sub 2} < EF < PEF and faster degradation was always obtained using BDD. PEF process with BDD yielded almost total mineralization following similar trends in SO{sub 4}{sup 2−}, ClO{sub 4}{sup −} and NO{sub 3}{sup −} media, whereas in Cl{sup −} medium, mineralization was inhibited by the formation of recalcitrant chloroderivatives. GC–MS analysis confirmed the cleavage of the −N=N− bond with formation of two main aromatics in SO{sub 4}{sup 2−} medium and three chloroaromatics in Cl{sup −} solutions. The effective oxidation of final oxalic and oxamic acids by BDD along with the photolysis of Fe(III)-oxalate species by UVA light accounted for the superiority of PEF with BDD. NH{sub 4

  8. Decolorization and mineralization of Allura Red AC aqueous solutions by electrochemical advanced oxidation processes

    International Nuclear Information System (INIS)

    Highlights: • Quicker degradation of Allura Red AC in the order EO-H2O2 < EF < PEF with Pt or BDD anode. • Almost total mineralization achieved by the most powerful PEF process with BDD. • Similar decolorization and mineralization rate in SO42−, ClO4− and NO3− media. • In Cl− medium, only slightly larger decolorization rate but strong inhibition of mineralization. • Identification of aromatic products, carboxylic acids and released NH4+, NO3− and SO42− ions. - Abstract: The decolorization and mineralization of solutions containing 230 mg L−1 of the food azo dye Allura Red AC at pH 3.0 have been studied upon treatment by electrochemical oxidation with electrogenerated H2O2 (EO-H2O2), electro-Fenton (EF) and photoelectro-Fenton (PEF). Experiments were performed with a stirred tank reactor containing a boron-doped diamond (BDD) or Pt anode and an air-diffusion cathode to generate H2O2. The main oxidants were hydroxyl radicals formed at the anode surface from water oxidation and in the bulk from Fenton’s reaction between H2O2 and added Fe2+. The oxidation ability increased in the sequence EO-H2O2 < EF < PEF and faster degradation was always obtained using BDD. PEF process with BDD yielded almost total mineralization following similar trends in SO42−, ClO4− and NO3− media, whereas in Cl− medium, mineralization was inhibited by the formation of recalcitrant chloroderivatives. GC–MS analysis confirmed the cleavage of the −N=N− bond with formation of two main aromatics in SO42− medium and three chloroaromatics in Cl− solutions. The effective oxidation of final oxalic and oxamic acids by BDD along with the photolysis of Fe(III)-oxalate species by UVA light accounted for the superiority of PEF with BDD. NH4+, NO3− and SO42− ions were released during the mineralization

  9. On-line sensor monitoring for chemical contaminant attenuation during UV/H2O2 advanced oxidation process.

    Science.gov (United States)

    Yu, Hye-Weon; Anumol, Tarun; Park, Minkyu; Pepper, Ian; Scheideler, Jens; Snyder, Shane A

    2015-09-15

    A combination of surrogate parameters and indicator compounds were measured to predict the removal efficiency of trace organic compounds (TOrCs) using low pressure (LP)-UV/H2O2 advanced oxidation process (AOP), engaged with online sensor-based monitoring system. Thirty-nine TOrCs were evaluated in two distinct secondary wastewater effluents in terms of estimated photochemical reactivity, as a function of the rate constants of UV direct photolysis (kUV) and hydroxyl radical (OH) oxidation (kOH). The selected eighteen TOrCs were classified into three groups that served as indicator compounds: Group 1 for photo-susceptible TOrCs but with minor degradation by OH oxidation (diclofenac, fluoxetine, iohexol, iopamidol, iopromide, simazine and sulfamethoxazole); Group 2 for TOrCs susceptible to both direct photolysis and OH oxidation (benzotriazole, diphenhydramine, ibuprofen, naproxen and sucralose); and Group 3 for photo-resistant TOrCs showing dominant degradation by OH oxidation (atenolol, carbamazepine, DEET, gemfibrozil, primidone and trimethoprim). The results indicate that TOC (optical-based measurement), UVA254 or UVT254 (UV absorbance or transmittance at 254 nm), and total fluorescence can all be used as suitable on-line organic surrogate parameters to predict the attenuation of TOrCs. Furthermore, the automated real-time monitoring via on-line surrogate sensors and equipped with the developed degradation profiles between sensor response and a group of TOrCs removal can provide a diagnostic tool for process control during advanced treatment of reclaimed waters. PMID:26074188

  10. Decolorization and removal of cod and bodfrom raw and biotreated textile dye bath effluent through advanced oxidation processes (AOPS)

    OpenAIRE

    Muhammad, A.; A. Shafeeq; Butt, M.A.; Z. H. Rizvi; M. A. Chughtai; Rehman, S.

    2008-01-01

    In this paper, a comparative study of the treatment of raw and biotreated (upflow anaerobic sludge blanket, UASB) textile dye bath effluent using advanced oxidation processes (AOPs) is presented. The AOPs applied on raw and biotreated textile dye bath effluent, after characterization in terms of COD, colour, BOD and pH, were ozone, UV, UV/H2O2 and photo-Fenton. The decolorization of raw dye bath effluent was 58% in the case of ozonation. However it was 98% in the case of biotreated dye bath e...

  11. Quantitative Analysis of Trace Chromium in Blood Samples. Combination of the Advanced Oxidation Process with Catalytic Adsorptive Stripping Voltammetry

    OpenAIRE

    Yong, Li; Armstrong, Kristie C.; Dansby-Sparks, Royce N.; Carrington, Nathan A.; Chambers, James Q.; Xue, Zi-Ling

    2006-01-01

    A new method for pretreating blood samples for trace Cr analysis is described. The Advanced Oxidation Process (AOP with H2O2 and 5.5-W irradiation for 60 min) is used to remove biological/organic species for subsequent analysis. Prior to the AOP pretreatment, acid (HNO3) is used at pH 3.0 to inhibit the enzyme catalase in the blood samples. Catalytic Adsorptive Stripping Voltammetry (CAdSV) at a bismuth film electrode (BiFE) gives Cr concentration of 6.0 ± 0.3 ppb in the blood samples. This c...

  12. Giardia duodenalis: Number and Fluorescence Reduction Caused by the Advanced Oxidation Process (H2O2/UV)

    OpenAIRE

    Guimarães, José Roberto; Franco, Regina Maura Bueno; Guadagnini, Regiane Aparecida; Santos, Luciana Urbano dos

    2014-01-01

    This study evaluated the effect of peroxidation assisted by ultraviolet radiation (H2O2/UV), which is an advanced oxidation process (AOP), on Giardia duodenalis cysts. The cysts were inoculated in synthetic and surface water using a concentration of 12 g H2O2 L−1 and a UV dose (λ=254 nm) of 5,480 mJcm−2. The aqueous solutions were concentrated using membrane filtration, and the organisms were observed using a direct immunofluorescence assay (IFA). The AOP was effective in reducing the number ...

  13. Catalytic performance of heteroatom-modified carbon nanotubes in advanced oxidation processes

    Institute of Scientific and Technical Information of China (English)

    João Restivo; Raquel P. Rocha; Adrián M. T. Silva; José J. M. Órfão; Manuel F. R. Pereira; José L. Figueiredo

    2014-01-01

    Multi-walled carbon nanotubes (CNTs) were submitted to chemical and thermal treatments in or-der to incorporate different heteroatoms on the surface. O-, S-and N-containing groups were suc-cessfully introduced onto the CNTs without significant changes of the textural properties. The cata-lytic activity of these heteroatom-modified CNTs was studied in two liquid phase oxidation pro-cesses:catalytic ozonation and catalytic wet air oxidation (CWAO), using oxalic acid and phenol as model compounds. In both cases, the presence of strongly acidic O-containing groups was found to decrease the catalytic activity of the CNTs. On the other hand, the introduction of S species (mainly sulfonic acids) enhanced the removal rate of the model compounds, particularly in the CWAO of phenol. Additional experiments were performed with a radical scavenger and sodium persulfate, in order to clarify the reaction mechanism. Nitrogen functionalities improve the catalytic performance of the original CNTs, regardless of the process or of the pollutant.

  14. Development of Head-end Pyrochemical Reduction Process for Advanced Oxide Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Park, B. H.; Seo, C. S.; Hur, J. M.; Jeong, S. M.; Hong, S. S.; Choi, I. K.; Choung, W. M.; Kwon, K. C.; Lee, I. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2008-12-15

    The development of an electrolytic reduction technology for spent fuels in the form of oxide is of essence to introduce LWR SFs to a pyroprocessing. In this research, the technology was investigated to scale a reactor up, the electrochemical behaviors of FPs were studied to understand the process and a reaction rate data by using U{sub 3}O{sub 8} was obtained with a bench scale reactor. In a scale of 20 kgHM/batch reactor, U{sub 3}O{sub 8} and Simfuel were successfully reduced into metals. Electrochemical characteristics of LiBr, LiI and Li{sub 2}Se were measured in a bench scale reactor and an electrolytic reduction cell was modeled by a computational tool.

  15. Decontamination of used pesticide packaging using advanced oxidation process by ionizing radiation

    International Nuclear Information System (INIS)

    The discharge of empty plastic packaging of pesticides can be an environmental concern causing problems to human health, animals and plants if done without inspection and monitoring. Among the commercial pesticides, chloropyrifos has significant importance because of its wide distribution and extensive use and persistence. The hydroxyl OH attack is the most efficient process of chemical oxidation. The radiation-induced degradation of chloropyrifos in liquid samples and in polyethylene pack was studied by gamma-radiolysis. Packaging of high density polyethylene tree layer co extruded, named COEX, and water samples contaminated with chloropyrifos, were irradiated using both, a multipurpose Co-60 gamma irradiator and a gamma source with 5,000 Ci total activity, Gamma cell type. The chemical analysis of the chloropyrifos and by-products were made using a gas chromatography associated to the mass spectrometry. Gamma radiation was efficient for removing chloropyrifos from the plastic packaging in all studied cases. (author)

  16. Implementation plan for automatic data processing equipment as part of the DYMAC advanced accountability system. Addendum 3 to applications of advanced accountability concepts in mixed oxide fabrication

    International Nuclear Information System (INIS)

    The Phase I study of the application of advanced accountability methods (DYMAC) in a uranium/plutonium mixed oxide facility was extended to include an implementation plan for the Automatic Data Processing System, as required by ERDA Manual Appendix 1830. The proposed system consists of a dual-control computer system with a minimum complement of peripheral equipment, which will be interfaced to the necessary measuring and display devices. Technical specifications for hardware and software system requirements are included, and cost estimates based on these specifications have been obtained

  17. Fully solar-driven thermo- and electrochemistry for advanced oxidation processes (STEP-AOPs) of 2-nitrophenol wastewater.

    Science.gov (United States)

    Nie, Chunhong; Shao, Nan; Wang, Baohui; Yuan, Dandan; Sui, Xin; Wu, Hongjun

    2016-07-01

    The STEP (Solar Thermal Electrochemical Process) for Advanced Oxidation Processes (AOPs, combined to STEP-AOPs), fully driven by solar energy without the input of any other forms of energy and chemicals, is introduced and demonstrated from the theory to experiments. Exemplified by the persistent organic pollutant 2-nitrophenol in water, the fundamental model and practical system are exhibited for the STEP-AOPs to efficiently transform 2-nitrophenol into carbon dioxide, water, and the other substances. The results show that the STEP-AOPs system performs more effectively than classical AOPs in terms of the thermodynamics and kinetics of pollutant oxidation. Due to the combination of solar thermochemical reactions with electrochemistry, the STEP-AOPs system allows the requisite electrolysis voltage of 2-nitrophenol to be experimentally decreased from 1.00 V to 0.84 V, and the response current increases from 18 mA to 40 mA. STEP-AOPs also greatly improve the kinetics of the oxidation at 30 °C and 80 °C. As a result, the removal rate of 2-nitrophenol after 1 h increased from 19.50% at 30 °C to 32.70% at 80 °C at constant 1.90 V. Mechanistic analysis reveals that the oxidation pathway is favorably changed because of thermal effects. The tracking of the reaction displayed that benzenediol and hydroquinone are initial products, with maleic acid and formic acid as sequential carboxylic acid products, and carbon dioxide as the final product. The theory and experiments on STEP-AOPs system exemplified by the oxidation of 2-nitrophenol provide a broad basis for extension of the STEP and AOPs for rapid and efficient treatment of organic wastewater. PMID:27093694

  18. An investigation into reservoir NOM reduction by UV photolysis and advanced oxidation processes.

    Science.gov (United States)

    Goslan, Emma H; Gurses, Filiz; Banks, Jenny; Parsons, Simon A

    2006-11-01

    A comparison of four treatment technologies for reduction of natural organic matter (NOM) in a reservoir water was made. The work presented here is a laboratory based evaluation of NOM treatment by UV-C photolysis, UV/H(2)O(2), Fenton's reagent (FR) and photo-Fenton's reagent (PFR). The work investigated ways of reducing the organic load on water treatment works (WTWs) with a view to treating 'in-reservoir' or 'in-pipe' before the water reaches the WTW. The efficiency of each process in terms of NOM removal was determined by measuring UV absorbance at 254 nm (UV(254)) and dissolved organic carbon (DOC). In terms of DOC reduction PFR was the most effective (88% removal after 1 min) however there were interferences when measuring UV(254) which was reduced to a lesser extent (31% after 1 min). In the literature, pH 3 is reported to be the optimal pH for oxidation with FR but here the reduction of UV(254) and DOC was found to be insensitive to pH in the range 3-7. The treatment that was identified as the most effective in terms of NOM reduction and cost effectiveness was PFR. PMID:16765416

  19. Application of Advanced Oxidation Process Using Gamma Radiation on the Biodegradation of Some Organic Pollutants

    International Nuclear Information System (INIS)

    Water samples were collected from Ras Gemsa on western coast of Suez Gulf, then microbiologically and chemically analyzed. The total petroleum hydrocarbon (TPH) concentration was detected of 340 ppm. On the other hand the biodegrading bacterial counts ( CFU ) clearly reflected the great adaptation of endogenous bacteria to use hydrocarbons as a sole source of carbon. The ratio of biodegrading bacteria to heterotrophic ones was about 3.5 %. The photooxidation process was studied using Titanium dioxide anatase powder, the results revealed that the rate of photo oxidation increase by increase of its concentration with optimum rate at 30 mg/100 ml. The biodegradation of hydrocarbons by Suez Gulf consortium was monitored with and without anatase powder, which revealed that the synergetic effect of using two techniques. The effect of radiation was studied with the biodegradation and photooxidation techniques, the maximum degradation was achieved by the triple treatment which minimize the residual hydrocarbons using radiated polluted microcosm at 6 kGy, Suez Gulf consortium and 30 mg/100 ml anatase powder in water.

  20. Destruction of microcystins by conventional and advanced oxidation processes: A review

    DEFF Research Database (Denmark)

    Sharma, Virender K.; Triantis, Theodoros M.; Antoniou, Maria G.;

    2012-01-01

    Cyanobacteria blooms pose an environmental hazard because of the release of water soluble toxic compounds, called cyanotoxins. Microcystins (MCs), hepatotoxic cyclic peptide toxins, are the most widespread cyanotoxins with microcystin-LR (MC-LR) the most common and toxic variant. Health effects of...... MCs have resulted in the need of using efficient treatment methods for the removal of this class of toxins in water supplies. While physical treatment methods can remove MCs at full or some extent from contaminated water, their function is primary separation of the whole toxins as intact molecules and...... oxidants is strongly affected by water quality parameters like pH, DOC and oxidant dose. Although there is a general trend for MCs oxidation (ozone>permanganate>chlorine>>>chlorine-based oxidants), the selection of the appropriate oxidant for toxin elimination during water treatment should be assessed for...

  1. An evaluation of a pilot-scale nonthermal plasma advanced oxidation process for trace organic compound degradation.

    Science.gov (United States)

    Gerrity, Daniel; Stanford, Benjamin D; Trenholm, Rebecca A; Snyder, Shane A

    2010-01-01

    This study evaluated a pilot-scale nonthermal plasma (NTP) advanced oxidation process (AOP) for the degradation of trace organic compounds such as pharmaceuticals and potential endocrine disrupting compounds (EDCs). The degradation of seven indicator compounds was monitored in tertiary-treated wastewater and spiked surface water to evaluate the effects of differing water qualities on process efficiency. The tests were also conducted in batch and single-pass modes to examine contaminant degradation rates and the remediation capabilities of the technology, respectively. Values for electrical energy per order (EEO) of magnitude degradation ranged from meprobamate) in wastewater. Changes in the bulk organic matter based on UV(254) absorbance and excitation-emission matrices (EEM) were also monitored and correlated to contaminant degradation. These results indicate that NTP may be a viable alternative to more common AOPs due to its comparable energy requirements for contaminant degradation and its ability to operate without any additional feed chemicals. PMID:19822343

  2. Decolorization and removal of cod and bodfrom raw and biotreated textile dye bath effluent through advanced oxidation processes (AOPS

    Directory of Open Access Journals (Sweden)

    A. Muhammad

    2008-09-01

    Full Text Available In this paper, a comparative study of the treatment of raw and biotreated (upflow anaerobic sludge blanket, UASB textile dye bath effluent using advanced oxidation processes (AOPs is presented. The AOPs applied on raw and biotreated textile dye bath effluent, after characterization in terms of COD, colour, BOD and pH, were ozone, UV, UV/H2O2 and photo-Fenton. The decolorization of raw dye bath effluent was 58% in the case of ozonation. However it was 98% in the case of biotreated dye bath effluent when exposed to UV/H2O2. It is, therefore, suggested that a combination of biotreatment and AOPs be adopted to decolorize dye bath effluent in order to make the process more viable and effective. Biodegradability was also improved by applying AOPs after biotreatment of dye bath effluent.

  3. 高级氧化技术处理造纸废水的应用研究%Application of Advanced Oxidation Processes in Papermaking Wastewater Treatment

    Institute of Scientific and Technical Information of China (English)

    杨德敏; 王兵

    2011-01-01

    The advanced oxidation processes has attracted more and more extensive attention due to its higher ability to remove the refractory organic materials in wastewater. The mechanism and the application development in papermaking wastewater treatment of the advanced oxidation processes, such as Fenton reagent oxidation, supercritical water oxidation, photocatalytic oxidation, ultrasonic oxidation, electrocatalytic oxidation, ozone oxidization and wet oxidation, are summarized. The characteristic and existing problems as well as the developing tendency of different advanced oxidation processes are analyzed.%介绍了Fenton类氧化法、超临界水氧化法、光催化氧化法、超声氧化法、电催化氧化法、臭氧氧化法和湿式氧化法等高级氧化技术的作用机理及其在造纸废水处理中的应用进展,分析并指出了各种高级氧化技术的特点以及存在的问题和今后的主要发展方向.

  4. Advanced oxidation processes: a review of fundamentals and applications in the treatment of urban and industrial wastewaters

    Directory of Open Access Journals (Sweden)

    Karla Santos de Araújo1;

    2016-04-01

    Full Text Available Contamination of water by toxic and/or recalcitrant species has great environmental impacts. In this context, Advanced Oxidation Processes (AOPs - technologies that principally use the hydroxyl radical (HO● for oxidation - have emerged as promising alternatives in treating urban and industrial wastewaters. This study reviewed the literature on POAs and presented data regarding the efficiency of these processes in pollutant degradation, comparing the theoretical reasoning and its industrial applications. The fundamentals and major applications of AOPs (chemical, photochemical, electrochemical, sonochemical and ozone-based processes, as well as their advantages and disadvantages, are described in this review. AOPs have been considered an effective alternative from a technical, economic and environmental viewpoint for the degradation of pollutants in effluents and industrial wastewater, despite having limitations such as high cost of available energy sources, development of new low-cost catalytic materials and construction of full-scale reactors. It is greatly important to the industrial application of AOPs to optimize the effectiveness of these factors.

  5. Ozonation and advanced oxidation processes as an option in waste water treatment for the elimination of endocrine disrupters and pharmaceuticals

    Energy Technology Data Exchange (ETDEWEB)

    Ried, A.; Mielcke, J.; Kampmann, M. [WEDECO Umwelttechnologie GmbH, Herford (Germany); Ternes, T.A.; Bonerz, M.; Herrmann, N.; Andersen, H. [ESWE-Inst. for Water Research and Water Technology, Wiesbaden, (Germany); Teiser, B. [Abwasserverband Braunschweig, Braunschweig (Germany)

    2003-07-01

    Treatment of waste water is limited due to the occurrence of persistent substances, germs, odors and/or colours, which were not totally degraded in municipal sewage treatment plants (STPs) using current waste water technology. Further trace pollutants with a relative high persistency in the waste water treatment are pharmaceuticals and personal care products (PPCPs). An appropriate waste water technology is needed to eliminate endocrine disrupters and PPCPs to avoid adverse effects in the receiving waters. Results of pilot trials are presented using the combined treatment technology ozone/UV. Additionally we will discuss the application and compare the cost of different advanced oxidation processes (AOP) for the treatment of an effluent of a municipal sewage treatment plant. (orig.)

  6. Advanced oxidation and reduction processes: Closed-loop applications for mixed waste

    International Nuclear Information System (INIS)

    At Los Alamos we are engaged in applying innovative oxidation and reduction technologies to the destruction of hazardous organics. Non thermal plasmas and relativistic electron-beams both involve the generation of free radicals and are applicable to a wide variety of mixed waste as closed-loop designs can be easily engineered. Silent discharge plasmas (SDP), long used for the generation of ozone, have been demonstrated in the laboratory to be effective in destroying hazardous organic compounds and offer an altemative to existing post-incineration and off-gas treatments. SDP generates very energetic electrons which efficiently create reactive free radicals, without adding the enthalpy associated with very high gas temperatures. A SDP cell has been used as a second stage to a LANL designed, packed-bed reactor (PBR) and has demonstrated DREs as high as 99.9999% for a variety of combustible liquid and gas-based waste streams containing scintillation fluids, nitrates, PCB surrogates, and both chlorinated and fluorinated solvents. Radiolytic treatment of waste using electron-beams and/or bremsstrahlung can be applied to a wide range of waste media (liquids, sludges, and solids). The efficacy and economy of these systems has been demonstrated for aqueous waste through both laboratory and pilot scale studies. We win present recent experimental and theoretical results for systems using stand alone SDP, combined PBR/SDP, and electron-beam treatment methods

  7. Comparison of different advanced oxidation processes (AOPs) in the presence of perovskites

    International Nuclear Information System (INIS)

    The efficacy of the oxidation systems: O3, UV radiation, O3/UV radiation, O3/perovskite, UV radiation/perovskite, O3/UV radiation/perovskite, H2O2/UV radiation, H2O2/UV radiation/perovskite, has been investigated by using pyruvic acid as probe compound. Under the operating conditions used, the combination of UV radiation and hydrogen peroxide (with or without perovskites) leads to the fastest pyruvic acid removal while the best results in terms of mineralization degree are obtained when combining O3/UV radiation/perovskite. The effect of the variables: inlet ozone (15-75 mg L-1) and initial pyruvic acid (10-3 to 10-2 M) concentrations, catalyst load (0.01-1.5 g L-1) and pH (2-9) was investigated for the photocatalytic ozonation. The most influencing parameter was the ozone concentration fed to the photoreactor. A zero order was observed for pyruvic acid concentration and close to zero for catalyst load. Some deactivation is observed after reusing the catalyst, likely due to leaching of the active phase

  8. Advanced oxidation process based on ozone/electron beam irradiation for treating groundwater

    International Nuclear Information System (INIS)

    There are several methods of generating OH free radicals from ozone and/or hydrogen peroxide and ultraviolet light. They all have in common that the OH free radicals originate in one single source only whereas in the combination of ozone with ionizing radiation two simultaneous working sources for the OH free radicals exist. The resulting higher OH free radical concentration makes this process especially apt for the remediation of low level contaminated groundwater as for example trichloroethylene (TCE) contamination in the sub-ppm range. A cost comparison between O3/UV and O3/electron beam for remediation of a groundwater contaminated with 100 ppb TCE indicated that for a throughput of about 5 million gallons/day the O3/electron beam process is more cost-effective. (authors)

  9. Study of herbicide ametryne degradation in HDPE packaging using the advanced oxidation process by ionizing radiation

    International Nuclear Information System (INIS)

    This study is part of the project with the objective to evaluate pesticides degradation for decontamination of commercial polymeric packaging of high density polyethylene, HDPE, used in agriculture. The herbicide used to this study was the herbicide ametryne (commercial name, Gesapax 500), due to its great use, mainly on field crops and on corn. Ametryne is commercialized since 1975, and, depending on the pesticide formulation and type of application, residues may be detectable in water, soil and on the surfaces for months or years. In order to evaluate the efficiency of radiation processing on removal the pesticides contamination, HDPE packaging were irradiated using Radiation Dynamics Electron Beam Accelerator with 1,5 MeV energy and 37 kW, in batch system. The samples were irradiated with water, in various absorbed doses. Ametryne was analyzed by gas chromatography (GC Shimadzu 17A), after extraction with hexane/dichloromethane (1:1 v/v) solution. The calibration curve was obtained with a regression coefficient of 0.986, and the relative standard deviation was lower than 10%. The radiation processing yield was evaluated by the rate of ametryne degradation and by the destruction G-value (Gd). The electron beam irradiation processing, showed high efficiency in destroying ametryne in the HDPE packaging when the samples were irradiated in presence of small quantities of water. (author)

  10. Ozonation and advanced oxidation by the peroxone process of ciprofloxacin in water

    International Nuclear Information System (INIS)

    A bubble reactor was used for ozonation of the antibiotic ciprofloxacin. Effects of process parameters ozone inlet concentration, ciprofloxacin concentration, temperature, pH and H2O2 concentration were tested. Desethylene ciprofloxacin was identified, based on HPLC-MS analysis, as one of the degradation products. Formation of desethylene ciprofloxacin was highly dependent on pH, with the highest concentration measured at pH 10. Radical scavengers t-butanol and parachlorobenzoic acid were added in order to gain mechanistic understanding. Radical species other than hydroxyl radicals were suggested to occur at acidic pH which can explain fast ciprofloxacin ozonation at pH 3

  11. Ozonation and advanced oxidation by the peroxone process of ciprofloxacin in water

    Energy Technology Data Exchange (ETDEWEB)

    Witte, Bavo de [Research Group EnVOC, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, B-9000 Ghent (Belgium); Dewulf, Jo [Research Group EnVOC, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, B-9000 Ghent (Belgium)], E-mail: jo.dewulf@UGent.be; Demeestere, Kristof; Langenhove, Herman van [Research Group EnVOC, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, B-9000 Ghent (Belgium)

    2009-01-30

    A bubble reactor was used for ozonation of the antibiotic ciprofloxacin. Effects of process parameters ozone inlet concentration, ciprofloxacin concentration, temperature, pH and H{sub 2}O{sub 2} concentration were tested. Desethylene ciprofloxacin was identified, based on HPLC-MS analysis, as one of the degradation products. Formation of desethylene ciprofloxacin was highly dependent on pH, with the highest concentration measured at pH 10. Radical scavengers t-butanol and parachlorobenzoic acid were added in order to gain mechanistic understanding. Radical species other than hydroxyl radicals were suggested to occur at acidic pH which can explain fast ciprofloxacin ozonation at pH 3.

  12. Application of Advanced Oxidation Processes in Water Treatment%高级氧化技术在水处理中的应用

    Institute of Scientific and Technical Information of China (English)

    黄洪勋; 孙亚全; 陈明发; 路艳艳

    2012-01-01

    This paper introduces the development and characteristics of advanced oxidation processes. Several advanced oxidation processes, such as chemical oxidation, photocatalytic oxidation, hydrothermal oxidation, high voltage pulsed discharge plasma and ultrasonic, and their application in water treatment are over- viewed. The application of advanced oxidation processes in water treatment will be more mature and be used more widely with the deepening of the research.%介绍了高级氧化技术的发展及其特点,并综述了化学氧化、光催化氧化、水热氧化以及高压脉冲放电等离子体、超声等高级氧化技术及其在水处理中的应用。随着对高级氧化技术不断深入的研究,其在水处理领域的应用将更加成熟并且越来越广泛。

  13. Surface water disinfection by chlorination and advanced oxidation processes: Inactivation of an antibiotic resistant E. coli strain and cytotoxicity evaluation.

    Science.gov (United States)

    Miranda, Andreza Costa; Lepretti, Marilena; Rizzo, Luigi; Caputo, Ivana; Vaiano, Vincenzo; Sacco, Olga; Lopes, Wilton Silva; Sannino, Diana

    2016-06-01

    The release of antibiotics into the environment can result in antibiotic resistance (AR) spread, which in turn can seriously affect human health. Antibiotic resistant bacteria have been detected in different aquatic environments used as drinking water source. Water disinfection may be a possible solution to minimize AR spread but conventional processes, such as chlorination, result in the formation of dangerous disinfection by-products. In this study advanced oxidation processes (AOPs), namely H2O2/UV, TiO2/UV and N-TiO2/UV, have been compared with chlorination in the inactivation of an AR Escherichia coli (E. coli) strain in surface water. TiO2 P25 and nitrogen doped TiO2 (N-TiO2), prepared by sol-gel method at two different synthesis temperatures (0 and -20°C), were investigated in heterogeneous photocatalysis experiments. Under the investigated conditions, chlorination (1.0mgL(-1)) was the faster process (2.5min) to achieve total inactivation (6 Log). Among AOPs, H2O2/UV resulted in the best inactivation rate: total inactivation (6 Log) was achieved in 45min treatment. Total inactivation was not observed (4.5 Log), also after 120min treatment, only for N-doped TiO2 synthesized at 0°C. Moreover, H2O2/UV and chlorination processes were evaluated in terms of cytotoxicity potential by means of 3-(4,5-dime-thylthiazol-2-yl)-2,5-diphenylte-trazolium colorimetric test on a human-derived cell line and they similarly affected HepG2 cells viability. PMID:26945469

  14. Phenol Photocatalytic Degradation by Advanced Oxidation Process under Ultraviolet Radiation Using Titanium Dioxide

    Directory of Open Access Journals (Sweden)

    Ali Nickheslat

    2013-01-01

    Full Text Available Background. The main objective of this study was to examine the photocatalytic degradation of phenol from laboratory samples and petrochemical industries wastewater under UV radiation by using nanoparticles of titanium dioxide coated on the inner and outer quartz glass tubes. Method. The first stage of this study was conducted to stabilize the titanium dioxide nanoparticles in anatase crystal phase, using dip-coating sol-gel method on the inner and outer surfaces of quartz glass tubes. The effect of important parameters including initial phenol concentration, TiO2 catalyst dose, duration of UV radiation, pH of solution, and contact time was investigated. Results. In the dip-coat lining stage, the produced nanoparticles with anatase crystalline structure have the average particle size of 30 nm and are uniformly distributed over the tube surface. The removal efficiency of phenol was increased with the descending of the solution pH and initial phenol concentration and rising of the contact time. Conclusion. Results showed that the light easily passes through four layers of coating (about 105 nm. The highest removal efficiency of phenol with photocatalytic UV/TiO2 process was 50% at initial phenol concentration of 30 mg/L, solution pH of 3, and 300 min contact time. The comparison of synthetic solution and petrochemical wastewater showed that at same conditions the phenol removal efficiency was equal.

  15. UASB reactor startup for the treatment of municipal wastewater followed by advanced oxidation process

    Directory of Open Access Journals (Sweden)

    Z. A. Bhatti

    2014-09-01

    Full Text Available The present study was done to shorten the start-up time of up-flow anaerobic sludge blanket (UASB reactor. Two different nutrients were used during the UASB start-up period, which was designed to decrease the hydraulic retention time (HRT from 48 to 24 and 12 to 6 hrs at average temperatures of 25-34 ºC. In the first stage, start-up was with glucose for 14 days and then the reactor was also fed with macro- and micronutrients as a synthetic nutrient influent (SNI from 15 to 45 days as the second stage. For the control, a second reactor was kept on glucose feeding from day 1 to 45. The removal efficiencies of the chemical oxygen demand (COD were 80% and 98% on the 6th and 32nd day of the first and second stage, respectively. The maximum substrate removal rate of 0.08 mg COD mg-1 VSS d-1 was observed for glucose and synthetic nutrient influent (SNI on the 8th and 40th days, respectively. When the reactor reached the maximum COD removal efficiency it was then shifted to municipal wastewater (MWW mixed with industrial wastewater. The HRT was reduced gradually with a one week gap while treating MWW. For further cleaning, the UASB effluent was treated with 40% waste hydrogen peroxide. The whole integrated treatment process was successful to reduce the COD by 99%, total suspended solids (TSS by 73%, total nitrogen (TN by 84% and turbidity by 67%.

  16. Review of iron-free Fenton-like systems for activating H2O2 in advanced oxidation processes

    International Nuclear Information System (INIS)

    Graphical abstract: - Highlights: • Elements with multiple redox states efficiently decompose H2O2 at neutral pH. • Activation of H2O2 is entirely governed by solution pH and catalyst composition. • Metal leaching and toxicity is an important factor for practical applications. • Iron-free Fenton systems work only in specialized reaction conditions. - Abstract: Iron-catalyzed hydrogen peroxide decomposition for in situ generation of hydroxyl radicals (HO• ) has been extensively developed as advanced oxidation processes (AOPs) for environmental applications. A variety of catalytic iron species constituting metal salts (in Fe2+ or Fe3+ form), metal oxides (e.g., Fe2O3, Fe3O4), and zero-valent metal (Fe0) have been exploited for chemical (classical Fenton), photochemical (photo-Fenton) and electrochemical (electro-Fenton) degradation pathways. However, the requirement of strict acidic conditions to prevent iron precipitation still remains the bottleneck for iron-based AOPs. In this article, we present a thorough review of alternative non-iron Fenton catalysts and their reactivity towards hydrogen peroxide activation. Elements with multiple redox states (like chromium, cerium, copper, cobalt, manganese and ruthenium) all directly decompose H2O2 into HO• through conventional Fenton-like pathways. The in situ formation of H2O2 and decomposition into HO• can be also achieved using electron transfer mechanism in zero-valent aluminum/O2 system. Although these Fenton systems (except aluminum) work efficiently even at neutral pH, the H2O2 activation mechanism is very specific to the nature of the catalyst and critically depends on its composition. This review describes in detail the complex mechanisms and emphasizes on practical limitations influencing their environmental applications

  17. Advanced Oxidation Degradation of Diclofenac

    International Nuclear Information System (INIS)

    Advanced oxidation/reduction processes (AO/RPs), utilize free radical reactions to directly degrade chemical contaminants as an alternative to traditional water treatment. This study reports the absolute rate constants for reaction of diclofenac sodium and the model compound (2, 6-dichloraniline) with the two major AO/RP radicals; the hydroxyl radical (•OH) and hydrated electron (e-aq). The bimolecular reaction rate constants (M-1 s-1) for diclofenac for •OH was (9.29 ± 0.11) x 109, and, for e- aq was (1.53 ± 0.03) x109. Preliminary degradation mechanisms are suggested based on product analysis using 60Co γ-irradiation and LC-MS for reaction by-product identification. The toxicity of products was evaluated using the Vibrio fischeri luminescent bacteria method. (author)

  18. Decolorization of Remazol Brilliant Blue Dye Effluent by Advanced Photo Oxidation Process (H2O2/UV system

    Directory of Open Access Journals (Sweden)

    A. S. Mahmoud

    2007-01-01

    Full Text Available Advanced photo oxidation processes hold great promise for the improved treatment of textile dye effluent. In this study, the effectiveness of a H2O2/UV system for the decolorization of remazol brilliant blue effluent was investigated by examining the optimum conditions for dye removal in two reactors (coil and conventional. The results showed that the coil reactor had a higher temperature profile than the conventional reactor. When the dye was fed into the reactors at 25˚C, UV radiation alone was not effective as the decolorization efficiency of the conventional reactor varied from 0.0 to 12.3%, while that of the coil reactor varied from 0.0 to 7.3%, depending on the residence time used. The effect of UV radiation at 100˚C was also negligible as the maximum decolorization efficiencies were 4.0 and 3.7% for the conventional and the coil reactors, respectively. Increasing the concentration of H2O2 increased decolorization efficiencies of both UV reactors. Dye decolorization also increased with residence time. More than 93% color removal of remazol brilliant blue dye was achieved with a residence time of 56 min and 100% decolorization achieved in 65 min using a H2O2 concentration of 12.50 mL Lˉ1.

  19. The decolorization and mineralization of Acid Orange 6 azo dye in aqueous solution by advanced oxidation processes: A comparative study

    International Nuclear Information System (INIS)

    The comparison of different advanced oxidation processes (AOPs), i.e. ultraviolet (UV)/TiO2, O3, O3/UV, O3/UV/TiO2, Fenton and electrocoagulation (EC), is of interest to determine the best removal performance for the destruction of the target compound in an Acid Orange 6 (AO6) solution, exploring the most efficient experimental conditions as well; on the other hand, the results may provide baseline information of the combination of different AOPs in treating industrial wastewater. The following conclusions can be drawn: (1) in the effects of individual and combined ozonation and photocatalytic UV irradiation, both O3/UV and O3/UV/TiO2 processes exhibit remarkable TOC removal capability that can achieve a 65% removal efficiency at pH 7 and O3 dose = 45 mg/L; (2) the optimum pH and ratio of [H2O2]/[Fe2+] found for the Fenton process, are pH 4 and [H2O2]/[Fe2+] = 6.58. The optimum [H2O2] and [Fe2+] under the same HF value are 58.82 and 8.93 mM, respectively; (3) the optimum applied voltage found in the EC experiment is 80 V, and the initial pH will affect the AO6 and TOC removal rates in that acidic conditions may be favorable for a higher removal rate; (4) the AO6 decolorization rate ranking was obtained in the order of O3 3/UV = O3/UV/TiO2 3 = Fenton 3/UV 3/UV/TiO2 for 30 min of reaction time

  20. Some ozone advanced oxidation processes to improve the biological removal of selected pharmaceutical contaminants from urban wastewater

    OpenAIRE

    Espejo, Azahara; Aguinaco, Almudena; Amat Payá, Ana María; Fernando J. Beltrán

    2014-01-01

    Removal of nine pharmaceutical compounds¿acetaminophen (AAF), antipyrine (ANT), caffeine (CAF), carbamazepine (CRB), diclofenac (DCF), hydrochlorothiazide (HCT), ketorolac (KET), metoprolol (MET) and sulfamethoxazole (SMX)¿spiked in a primary sedimentation effluent of a municipal wastewater has been studied with sequential aerobic biological and ozone advanced oxidation systems. Combinations of ozone, UVA black light and Fe(III) or Fe3O4 constituted the chemical systems. During the ...

  1. Electrokinetic treatment of polluted soil at pilot level coupled to an advanced oxidation process of its wastewater

    Science.gov (United States)

    Ochoa, B.; Ramos, L.; Garibay, A.; Pérez-Corona, M.; Cuevas, M. C.; Cárdenas, J.; Teutli, M.; Bustos, E.

    2016-02-01

    Soil contaminated with hydrocarbons is a current problem of great importance. These contaminants may be toxic, can retain water and block gas exchange with the atmosphere, which produces a poor-quality soil unsuitable for ecological health. Electroremediation is among the treatments for the removal of such contaminants. In this research, a pilot-level electroremediation test was applied using a circular arrangement of electrodes with a Ti cathode at the middle of the cell surrounded by six IrO2-Ta2O5 | Ti anodes. The presence of an NaOH electrolyte helps to develop the electromigration and electro-osmosis of gasoline molecules (at 1126 mg kg-1) surrounded by Na+ ions. The hydrocarbons are directed towards the cathode and subsequently removed in an aqueous Na+ - hydrocarbon solution, and the -OH migrates to the anode. During electrokinetic treatment, the physicochemical characteristics of the soil close to either the cathode or anode and at the half-cell were evaluated during the three weeks of treatment. During that time, more than 80% of hydrocarbons were removed. Hydrocarbons removed by the electrokinetic treatment of gasoline-polluted soil were collected in a central wastewater compartment and subsequently treated with a Fenton-type advanced oxidation process. This achieved more than 70% mineralization of the hydrocarbons to CO2 and H2O within 1.5 h; its low toxicity status was verified using the Deltatox® kit test. With this approach, the residual water complied with the permissible limits of COD, pH, and electrical conductivity for being discharged into water bodies, according to Mexican norm NOM-001-SEMARNAT-1996.

  2. The state-of-the art of produced water treatment by oxidative advanced processes; Atual estagio de desenvolvimento dos processos oxidativos avancados para o tratamento da agua produzida

    Energy Technology Data Exchange (ETDEWEB)

    Cortes, Marcela de A.H.; Marques, Jose Jailton; Rocha, Inaura C.C. da [Universidade Federal de Sergipe (UFS), Aracaju, SE (Brazil). Dept. de Engenharia Quimica

    2008-07-01

    The oily wastewater generated in petroleum exploration contains a sort of contaminants that may cause significant environmental impact. For this reason, the number of researchers that are looking for cleaner techniques to treat this kind of wastewater is growing. The advanced oxidation processes (AOPs) are clean and non-selective processes largely used to the treatment of wastewater containing critical substances like textile dyes, pesticides, PCBs, PAHs etc. The treatment systems using AOPs can be homogeneous or heterogeneous and they may use irradiation or not. This work presents a compilation of the results found by many researchers involving AOPs potentially applicable to the treatment of produced water, as follow: H{sub 2}O{sub 2}/UV, H{sub 2}O{sub 2} / Fe{sup 2+} / UV, O{sub 3}/UV, O{sub 3}/ H{sub 2}O{sub 2} etc., showing the state-of-art of oxidation advanced processes. (author)

  3. The decolorization and mineralization of Acid Orange 6 azo dye in aqueous solution by advanced oxidation processes: A comparative study

    Energy Technology Data Exchange (ETDEWEB)

    Hsing, H.-J. [Graduate Institute of Environmental Engineering, National Taiwan University, 71 Chou-Shan Road, Taipei 106, Taiwan (China); Chiang, P.-C. [Graduate Institute of Environmental Engineering, National Taiwan University, 71 Chou-Shan Road, Taipei 106, Taiwan (China)]. E-mail: pcchiang@ntu.edu.tw; Chang, E.-E. [Department of Biochemistry, Taipei Medical University, 25 Wu-Shin Street, Taipei 106, Taiwan (China); Chen, M.-Y. [Graduate Institute of Environmental Engineering, National Taiwan University, 71 Chou-Shan Road, Taipei 106, Taiwan (China)

    2007-03-06

    The comparison of different advanced oxidation processes (AOPs), i.e. ultraviolet (UV)/TiO{sub 2}, O{sub 3}, O{sub 3}/UV, O{sub 3}/UV/TiO{sub 2}, Fenton and electrocoagulation (EC), is of interest to determine the best removal performance for the destruction of the target compound in an Acid Orange 6 (AO6) solution, exploring the most efficient experimental conditions as well; on the other hand, the results may provide baseline information of the combination of different AOPs in treating industrial wastewater. The following conclusions can be drawn: (1) in the effects of individual and combined ozonation and photocatalytic UV irradiation, both O{sub 3}/UV and O{sub 3}/UV/TiO{sub 2} processes exhibit remarkable TOC removal capability that can achieve a 65% removal efficiency at pH 7 and O{sub 3} dose = 45 mg/L; (2) the optimum pH and ratio of [H{sub 2}O{sub 2}]/[Fe{sup 2+}] found for the Fenton process, are pH 4 and [H{sub 2}O{sub 2}]/[Fe{sup 2+}] = 6.58. The optimum [H{sub 2}O{sub 2}] and [Fe{sup 2+}] under the same HF value are 58.82 and 8.93 mM, respectively; (3) the optimum applied voltage found in the EC experiment is 80 V, and the initial pH will affect the AO6 and TOC removal rates in that acidic conditions may be favorable for a higher removal rate; (4) the AO6 decolorization rate ranking was obtained in the order of O{sub 3} < O{sub 3}/UV = O{sub 3}/UV/TiO{sub 2} < EC < Fenton; (5) the ranking of TOC removal efficiency of selected AOPs was in the order of O{sub 3} = Fenton < EC < O{sub 3}/UV < O{sub 3}/UV/TiO{sub 2} for 30 min of reaction time.

  4. Advanced Biosignal Processing

    CERN Document Server

    Nait-Ali, Amine

    2009-01-01

    Presents the principle of many advanced biosignal processing techniques. This title introduces the main biosignal properties and the acquisition techniques. It concerns one of the most intensively used biosignals in the clinical routine, namely the Electrocardiogram, the Elektroenzephalogram, the Electromyogram and the Evoked Potential

  5. Experimental research on influencing factors of wet removal of NO from coal-fired flue gas by UV/H2O2 advanced oxidation process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Wet removal of NO from coal-fired flue gas by UV/H2O2 Advanced Oxidation Process (AOP) were investigated in a self-designed UV-bubble reactor. Several main influencing factors (UV intensity, H2O2 initial concentration, initial pH value, solution temperature, NO initial concentration, liquid-gas ratio and O2 percentage content) on the NO removal efficiency were studied. The results showed that UV intensity, H2O2 initial concentration, NO initial concentration and liquid-gas ratio are the main influencing factors. In the best conditions, the highest NO removal efficiency by UV/H2O2 advanced oxidation process could reach 82.9%. Based on the experimental study, the influencing mechanism of the relevant influencing factors were discussed in depth.

  6. Advanced uranium enrichment processes

    International Nuclear Information System (INIS)

    Three advanced Uranium enrichment processes are dealt with in the report: AVLIS (Atomic Vapour LASER Isotope Separation), MLIS (Molecular LASER Isotope Separation) and PSP (Plasma Separation Process). The description of the physical and technical features of the processes constitutes a major part of the report. If further presents comparisons with existing industrially used enrichment technologies, gives information on actual development programmes and budgets and ends with a chapter on perspectives and conclusions. An extensive bibliography of the relevant open literature is added to the different subjects discussed. The report was drawn up by the nuclear research Centre (CEA) Saclay on behalf of the Commission of the European Communities

  7. Determination of Effective Parameters on Removal of Organic Materials from Pharmaceutical Industry Wastewater by Advanced Oxidation Process (H2O2/UV)

    OpenAIRE

    Esmaeil Azizi; Mehdi Ghayebzadeh; Abdollah Dargahi; Lida Hemati; Masoumeh Beikmohammadi; Kiomars Sharafi

    2016-01-01

    Background & Aims of the Study: Pharmaceutical wastewater is one of the major complex and toxic industrial effluents that contain little or no biodegradable organic matters. Materials & Methods: In this study, H2O2/UV base advance oxidation process (AOP) was used to remove organic materials from pharmaceutical industry effluent. Experiments were conducted for the chemical oxygen demand (COD) removal using medium pressure mercury vapor UV lamp coupled with hydrogen peroxide (H2O2/UV). ...

  8. Degradation of chlorophenols and alkylphenol ethoxylates, two representative textile chemicals, in water by advanced oxidation processes: the state of the art on transformation products and toxicity.

    Science.gov (United States)

    Karci, Akin

    2014-03-01

    Advanced oxidation processes based on the generation of reactive species including hydroxyl radicals are viable options in eliminating a wide array of refractory organic contaminants in industrial effluents. The assessment of transformation products and toxicity should be, however, the critical point that would allow the overall efficiency of advanced oxidation processes to be better understood and evaluated since some transformation products could have an inhibitory effect on certain organisms. This article reviews the most recent studies on transformation products and toxicity for evaluating advanced oxidation processes in eliminating classes of compounds described as "textile chemicals" from aqueous matrices and poses questions in need of further investigation. The scope of this paper is limited to the scientific studies with two classes of textile chemicals, namely chlorophenols and alkylphenol ethoxylates, whose use in textile industry is a matter of debate due to health risks to humans and harm to the environment. The article also raises the critical question: What is the state of the art knowledge on relationships between transformation products and toxicity? PMID:24216260

  9. Advanced oxidation processes (AOPs) involving ultrasound for waste water treatment: a review with emphasis on cost estimation.

    Science.gov (United States)

    Mahamuni, Naresh N; Adewuyi, Yusuf G

    2010-08-01

    Two things are needed for any technology to be suitable for use in the industry, viz. 1. Technical feasibility and 2. Economical feasibility. The use of ultrasound for waste water treatment has been shown to be technically feasible by numerous reports in the literature over the years. But there are hardly any exhaustive reports which address the issue of economical feasibility of the use of ultrasound for waste water treatment on industrial scale. Hence an attempt was made to estimate the cost for the waste water treatment using ultrasound. The costs have been calculated for 1000 L/min capacity treatment plant. The costs were calculated based upon the rate constants for pollutant degradation. The pollutants considered were phenol, trichloroethylene (TCE) and reactive azo dyes. Time required for ninety percent degradation of pollutant was taken as the residence time. The amount of energy required to achieve the target degradation was calculated from the energy density (watt/ml) used in the treatability study. The cost of treatment was calculated by considering capital cost and operating cost involved for the waste water treatment. Quotations were invited from vendors to ascertain the capital cost of equipments involved and operating costs were calculated based on annual energy usage. The cost was expressed in dollars per 1000 gallons of waste water treated. These treatment costs were compared with other established Advanced Oxidation Process (AOP) technologies. The cost of waste water treatment for phenol was in the range of $89 per 1000 gallons for UV/US/O(3) to $15,536 per 1000 gallons for US alone. These costs for TCE were in the range of $25 per 1000 gallons to $91 for US+UV treatment and US alone, respectively. The cost of waste water treatment for reactive azo dyes was in the range of $65 per 1000 gallon for US+UV+H(2)O(2) to $14,203 per 1000 gallon for US alone. This study should help in quantifying the economics of waste water treatment using ultrasound on

  10. Effectiveness of UV-based advanced oxidation processes for the remediation of hydrocarbon pollution in the groundwater: A laboratory investigation

    International Nuclear Information System (INIS)

    The effectiveness of advanced oxidation processes in a batch and a flow reactor was investigated for the remediation of hydrocarbon pollution in the groundwater underlying a petrochemical industrial site. The main organic contaminants present in the groundwater were MTBE, benzene, alkyl-benzenes and alkyl-naphthalenes. Experimental results with a batch reactor showed that for all the organic contaminants the removal efficiency order is UV/TiO2 ∼ UV/H2O2 > UV (medium-pressure) in a synthetic aqueous solution, compared to UV/H2O2 > UV (medium-pressure) > UV/TiO2 for the real polluted groundwater. The much lower performance of UV/TiO2 with respect to UV/H2O2 was inferred to the matrix of the groundwater, i.e. the salt content, as well as the organic and particulate matter. In fact, it is likely that the salts and dissolved organic matter quench the superoxide anion O2·- and hydroxyl radicals just formed at the surface of the TiO2 catalyst. MTBE was the hardest compound to remove with each of the investigated treatments. UV and UV/TiO2 treatments were not able to reach a residual concentration of 10 μg/L (set by Italian legislation) even after 180 min. As for the UV/H2O2 process, only the MTBE degradation rate resulted affected by the initial H2O2 concentration, while for other compounds a complete removal was obtained within 20 min even with the lowest H2O2 concentration used (0.13 g/L). Only after 120 min of treatment, with an initial H2O2 concentration of 0.13 g/L, did the residual MTBE concentration fall below the above reported maximum admissible concentration. Instead, by using an initial concentration of 2 g/L a residual concentration lower than 5 μg/L was obtained after just 30 min of reaction. The UV/H2O2 process was also investigated with a flow reactor. Results showed that it was more efficient than the batch reactor for removing MTBE, in terms of reaction time and initial H2O2 concentration required. This is consistent with the higher power of the UV

  11. Effectiveness of UV-based advanced oxidation processes for the remediation of hydrocarbon pollution in the groundwater: a laboratory investigation.

    Science.gov (United States)

    Mascolo, Giuseppe; Ciannarella, Ruggero; Balest, Lydia; Lopez, Antonio

    2008-04-15

    The effectiveness of advanced oxidation processes in a batch and a flow reactor was investigated for the remediation of hydrocarbon pollution in the groundwater underlying a petrochemical industrial site. The main organic contaminants present in the groundwater were MTBE, benzene, alkyl-benzenes and alkyl-naphthalenes. Experimental results with a batch reactor showed that for all the organic contaminants the removal efficiency order is UV/TiO2 approximately UV/H2O2>UV (medium-pressure) in a synthetic aqueous solution, compared to UV/H2O2>UV (medium-pressure)>UV/TiO2 for the real polluted groundwater. The much lower performance of UV/TiO2 with respect to UV/H2O2 was inferred to the matrix of the groundwater, i.e. the salt content, as well as the organic and particulate matter. In fact, it is likely that the salts and dissolved organic matter quench the superoxide anion O2(-) and hydroxyl radicals just formed at the surface of the TiO2 catalyst. MTBE was the hardest compound to remove with each of the investigated treatments. UV and UV/TiO2 treatments were not able to reach a residual concentration of 10 microg/L (set by Italian legislation) even after 180 min. As for the UV/H2O2 process, only the MTBE degradation rate resulted affected by the initial H2O2 concentration, while for other compounds a complete removal was obtained within 20 min even with the lowest H2O2 concentration used (0.13 g/L). Only after 120 min of treatment, with an initial H2O2 concentration of 0.13 g/L, did the residual MTBE concentration fall below the above reported maximum admissible concentration. Instead, by using an initial concentration of 2g/L a residual concentration lower than 5 microg/L was obtained after just 30 min of reaction. The UV/H2O2 process was also investigated with a flow reactor. Results showed that it was more efficient than the batch reactor for removing MTBE, in terms of reaction time and initial H2O2 concentration required. This is consistent with the higher power of

  12. Advanced information processing system

    Science.gov (United States)

    Lala, J. H.

    1984-01-01

    Design and performance details of the advanced information processing system (AIPS) for fault and damage tolerant data processing on aircraft and spacecraft are presented. AIPS comprises several computers distributed throughout the vehicle and linked by a damage tolerant data bus. Most I/O functions are available to all the computers, which run in a TDMA mode. Each computer performs separate specific tasks in normal operation and assumes other tasks in degraded modes. Redundant software assures that all fault monitoring, logging and reporting are automated, together with control functions. Redundant duplex links and damage-spread limitation provide the fault tolerance. Details of an advanced design of a laboratory-scale proof-of-concept system are described, including functional operations.

  13. Advanced Polymer Processing Facility

    Energy Technology Data Exchange (ETDEWEB)

    Muenchausen, Ross E. [Los Alamos National Laboratory

    2012-07-25

    Some conclusions of this presentation are: (1) Radiation-assisted nanotechnology applications will continue to grow; (2) The APPF will provide a unique focus for radiolytic processing of nanomaterials in support of DOE-DP, other DOE and advanced manufacturing initiatives; (3) {gamma}, X-ray, e-beam and ion beam processing will increasingly be applied for 'green' manufacturing of nanomaterials and nanocomposites; and (4) Biomedical science and engineering may ultimately be the biggest application area for radiation-assisted nanotechnology development.

  14. Integration of biofiltration and advanced oxidation processes for tertiary treatment of an oil refinery wastewater aiming at water reuse.

    Science.gov (United States)

    Nogueira, A A; Bassin, J P; Cerqueira, A C; Dezotti, M

    2016-05-01

    The combination of biological and chemical oxidation processes is an interesting approach to remove ready, poor, and non-biodegradable compounds from complex industrial wastewaters. In this study, biofiltration followed by H2O2/UV oxidation (or microfiltration) and final reverse osmosis (RO) step was employed for tertiary treatment of an oil refinery wastewater. Biofiltration alone allowed obtaining total organic carbon (TOC), chemical oxygen demand (COD), UV absorbance at 254 nm (UV254), ammonium, and turbidity removal of around 46, 46, 23, 50, and 61 %, respectively. After the combined biological-chemical oxidation treatment, TOC and UV254 removal amounted to 88 and 79 %, respectively. Whereas, the treatment performance achieved with different UV lamp powers (55 and 95 W) and therefore distinct irradiance levels (26.8 and 46.3 mW/cm(2), respectively) were very similar and TOC and UV254 removal rates were highly affected by the applied C/H2O2 ratio. Silt density index (SDI) was effectively reduced by H2O2/UV oxidation, favoring further RO application. C/H2O2 ratio of 1:4, 55 W UV lamp, and 20-min oxidation reaction corresponded to the experimental condition which provided the best cost/benefit ratio for TOC, UV254, and SDI reduction from the biofilter effluent. The array of treatment processes proposed in this study has shown to be adequate for tertiary treatment of the oil refinery wastewater, ensuring the mitigation of membrane fouling problems and producing a final effluent which is suitable for reuse applications. PMID:26850095

  15. Advanced materials processing

    International Nuclear Information System (INIS)

    Advanced materials will require improved processing methods due to high melting points, low toughness or ductility values, high reactivity with air or ceramics and typically complex crystal structures with significant anisotropy in flow and/or fracture stress. Materials for structural applications at elevated temperature in critical systems will require processing with a high degree of control. This requires an improved understanding of the relationship between process variables and microstructure to enable control systems to achieve consistently high quality. One avenue to the required level of understanding is computer simulation. Past attempts to do process modeling have been hampered by incomplete data regarding thermophysical or mechanical material behavior. Some of the required data can be calculated. Due to the advances in software and hardware, accuracy and costs are in the realm of acquiring experimental data. Such calculations can, for example, be done at an atomic level to compute lattice energy, fault energies, density of states and charge densities. These can lead to fundamental information about the competition between slip and fracture, anisotropy of bond strength (and therefore cleavage strength), cohesive strength, adhesive strength, elastic modulus, thermal expansion and possibly other quantities which are difficult (and therefore expensive to measure). Some of these quantities can be fed into a process model. It is probable that temperature dependencies can be derived numerically as well. Examples are given of the beginnings of such an approach for Ni3Al and MoSi2. Solidification problems are examples of the state-of-the-art process modeling and adequately demonstrate the need for extensive input data. Such processes can be monitored in terms of interfacial position vs. time, cooling rate and thermal gradient

  16. Conversion of Chromium(III) Propionate to Chromate/dichromate(VI) by the Advanced Oxidation Process. Pretreatment of a Biomimetic Complex for Metal Analysis

    OpenAIRE

    Lynn Rodman, D.; Carrington, Nathan A.; Xue, Zi-Ling

    2006-01-01

    The use of H2O2 and UV irradiation to remove organic ligands in a chromium(III) complex for the subsequent chromium analysis is reported. The Advanced Oxidation Process (AOP) using a 5.5-W UV lamp, H2O2 and Fe2+/Fe3+ as catalyst (photo Fenton process) was found to give complete and quantitative Cr(III) → Cr(VI) conversion and removal of ligands in chromium(III) propionate [Cr3O(O2CCH2CH3)6(H2O)3]NO3, a biomimetic chromium species, as subsequent chromium analyses by the 1,5-diphenylcarbazide m...

  17. Degradação de fármacos residuais por processos oxidativos avançados Degradation of residual pharmaceuticals by advanced oxidation processes

    Directory of Open Access Journals (Sweden)

    Silene Alessandra Santos Melo

    2009-01-01

    Full Text Available The concern about aquatic ecosystems and the potential risk of drinking water contamination by pharmaceuticals have stimulated the study of processes for the efficient degradation of these contaminants, since the conventional treatment have been inefficient on that purpose. The advanced oxidation processes (AOPs appear as viable alternatives due to their efficiency on the degradation of different classes of organic contaminants. This review presents an overview of the main AOP (O3, H2O2/UV, TiO2/UV, Fenton and photo-Fenton which have been applied to the degradation of different pharmaceuticals. The main results obtained, intermediates identified and toxicity data are presented.

  18. Integration of traditional systems and advanced oxidation process technologies for the industrial treatment of olive mill wastewaters.

    Science.gov (United States)

    Amaral-Silva, Nuno; Martins, Rui C; Castro-Silva, Sérgio; Quinta-Ferreira, Rosa M

    2016-10-01

    A complete industrial treatment system (involving the integration of coagulation/flocculation and Fenton processes) to depurate real wastewaters coming from two-phase olive oil production mills has been studied. The experimental results indicated that at the end of this combined strategy, involving a primary physical separation stage followed by Fenton's chemical oxidation, chemical oxygen demand (COD) is reduced up to 90% and total polyphenols' concentration is decreased up to 92%. The treated stream biodegradability (BOD5/COD) reached 0.52 and the Total Suspended Solids (TSSs) and Total Dissolved Solids (TDSs) decreased up to 95% and 69%, respectively. Fenton's procedure was optimized bearing in mind the pH adjustment step, different procedures for hydrogen peroxide addition and the use of coagulants instead of the chemical precipitation (by raising pH) to promote iron sludge settling. Our results demonstrated that pH (3.0 ± 0.1) control during the oxidation reaction improves the oxidation efficiency. Moreover, the final NaOH addition is essential to a better sludge formation and consequent precipitation of the residual iron removing also some organic matter. PMID:26878594

  19. Mineralization of salicylic acid in acidic aqueous medium by electrochemical advanced oxidation processes using platinum and boron-doped diamond as anode and cathodically generated hydrogen peroxide.

    Science.gov (United States)

    Guinea, Elena; Arias, Conchita; Cabot, Pere Lluís; Garrido, José Antonio; Rodríguez, Rosa María; Centellas, Francesc; Brillas, Enric

    2008-01-01

    Solutions containing 164 mg L(-1) salicylic acid of pH 3.0 have been degraded by electrochemical advanced oxidation processes such as anodic oxidation, anodic oxidation with electrogenerated H(2)O(2), electro-Fenton, photoelectro-Fenton and solar photoelectro-Fenton at constant current density. Their oxidation power has been comparatively studied in a one-compartment cell with a Pt or boron-doped diamond (BDD) anode and a graphite or O(2)-diffusion cathode. In the three latter procedures, 0.5mM Fe(2+) is added to the solution to form hydroxyl radical (()OH) from Fenton's reaction between Fe(2+) and H(2)O(2) generated at the O(2)-diffusion cathode. Total mineralization is attained for all methods with BDD and for photoelectro-Fenton and solar photoelectro-Fenton with Pt. The poor decontamination achieved in anodic oxidation and electro-Fenton with Pt is explained by the slow removal of most pollutants by ()OH formed from water oxidation at the Pt anode in comparison to their quick destruction with ()OH produced at BDD. ()OH generated from Fenton's reaction oxidizes rapidly all aromatic pollutants, but it cannot destroy final Fe(III)-oxalate complexes. Solar photoelectro-Fenton treatments always yield quicker degradation rate due to the very fast photodecarboxylation of these complexes by UVA irradiation supplied by solar light. The effect of current density on the degradation rate, efficiency and energy cost of all methods is examined. The salicylic acid decay always follows a pseudo-first-order kinetics. 2,3-Dihydroxybenzoic, 2,5-dihydroxybenzoic, 2,6-dihydroxybenzoic, alpha-ketoglutaric, glycolic, glyoxylic, maleic, fumaric, malic, tartronic and oxalic acids are detected as oxidation products. A general reaction sequence for salicylic acid mineralization considering all these intermediates is proposed. PMID:17692891

  20. Advances in speech processing

    Science.gov (United States)

    Ince, A. Nejat

    1992-10-01

    The field of speech processing is undergoing a rapid growth in terms of both performance and applications and this is fueled by the advances being made in the areas of microelectronics, computation, and algorithm design. The use of voice for civil and military communications is discussed considering advantages and disadvantages including the effects of environmental factors such as acoustic and electrical noise and interference and propagation. The structure of the existing NATO communications network and the evolving Integrated Services Digital Network (ISDN) concept are briefly reviewed to show how they meet the present and future requirements. The paper then deals with the fundamental subject of speech coding and compression. Recent advances in techniques and algorithms for speech coding now permit high quality voice reproduction at remarkably low bit rates. The subject of speech synthesis is next treated where the principle objective is to produce natural quality synthetic speech from unrestricted text input. Speech recognition where the ultimate objective is to produce a machine which would understand conversational speech with unrestricted vocabulary, from essentially any talker, is discussed. Algorithms for speech recognition can be characterized broadly as pattern recognition approaches and acoustic phonetic approaches. To date, the greatest degree of success in speech recognition has been obtained using pattern recognition paradigms. It is for this reason that the paper is concerned primarily with this technique.

  1. Advanced powder processing

    Energy Technology Data Exchange (ETDEWEB)

    Janney, M.A. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    Gelcasting is an advanced powder forming process. It is most commonly used to form ceramic or metal powders into complex, near-net shapes. Turbine rotors, gears, nozzles, and crucibles have been successfully gelcast in silicon nitride, alumina, nickel-based superalloy, and several steels. Gelcasting can also be used to make blanks that can be green machined to near-net shape and then high fired. Green machining has been successfully applied to both ceramic and metal gelcast blanks. Recently, the authors have used gelcasting to make tooling for metal casting applications. Most of the work has centered on H13 tool steel. They have demonstrated an ability to gelcast and sinter H13 to near net shape for metal casting tooling. Also, blanks of H13 have been cast, green machined into complex shape, and fired. Issues associated with forming, binder burnout, and sintering are addressed.

  2. Advanced microwave processing concepts

    Energy Technology Data Exchange (ETDEWEB)

    Lauf, R.J.; McMillan, A.D.; Paulauskas, F.L. [Oak Ridge National Laboratory, TN (United States)

    1995-05-01

    The purpose of this work is to explore the feasibility of several advanced microwave processing concepts to develop new energy-efficient materials and processes. The project includes two tasks: (1) commercialization of the variable-frequency microwave furnace; and (2) microwave curing of polymer composites. The variable frequency microwave furnace, whose initial conception and design was funded by the AIC Materials Program, will allow us, for the first time, to conduct microwave processing studies over a wide frequency range. This novel design uses a high-power traveling wave tube (TWT) originally developed for electronic warfare. By using this microwave source, one can not only select individual microwave frequencies for particular experiments, but also achieve uniform power densities over a large area by the superposition of many different frequencies. Microwave curing of thermoset resins will be studied because it hold the potential of in-situ curing of continuous-fiber composites for strong, lightweight components. Microwave heating can shorten curing times, provided issues of scaleup, uniformity, and thermal management can be adequately addressed.

  3. Advanced microwave processing concepts

    Energy Technology Data Exchange (ETDEWEB)

    Lauf, R.J.; McMillan, A.D.; Paulauskas, F.L. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    The purpose of this work is to explore the feasibility of several advanced microwave processing concepts to develop new energy-efficient materials and processes. The project includes two tasks: (1) commercialization of the variable-frequency microwave furnace; and (2) microwave curing of polymeric materials. The variable frequency microwave furnace, whose initial conception and design was funded by the AIM Materials Program, allows the authors, for the first time, to conduct microwave processing studies over a wide frequency range. This novel design uses a high-power traveling wave tube (TWT) originally developed for electronic warfare. By using this microwave source, one can not only select individual microwave frequencies for particular experiments, but also achieve uniform power densities over a large area by the superposition of many different frequencies. Microwave curing of various thermoset resins will be studied because it holds the potential of in-situ curing of continuous-fiber composites for strong, lightweight components or in-situ curing of adhesives, including metal-to-metal. Microwave heating can shorten curing times, provided issues of scaleup, uniformity, and thermal management can be adequately addressed.

  4. High frequency ultrasound as a selective advanced oxidation process to remove penicillinic antibiotics and eliminate its antimicrobial activity from water.

    Science.gov (United States)

    Serna-Galvis, Efraim A; Silva-Agredo, Javier; Giraldo-Aguirre, Ana L; Flórez-Acosta, Oscar A; Torres-Palma, Ricardo A

    2016-07-01

    This work studies the sonochemical degradation of a penicillinic antibiotic (oxacillin) in simulated pharmaceutical wastewater. High frequency ultrasound was applied to water containing the antibiotic combined with mannitol or calcium carbonate. In the presence of additives, oxacillin was efficiently removed through sonochemical action. For comparative purposes, the photo-Fenton, TiO2 photocatalysis and electrochemical oxidation processes were also tested. Therefore, the evolution of the antibiotic and its associated antimicrobial activity (AA) were monitored. A high inhibition was found for the other three oxidation processes in the elimination of the antimicrobial activity caused by the additives; while for the ultrasonic treatment, a negligible effect was observed. The sonochemical process was able to completely degrade the antibiotic, generating solutions without AA. In fact, the elimination of antimicrobial activity showed an excellent performance adjusted to exponential kinetic-type decay. The main sonogenerated organic by-products were determined by means of HPLC-MS. Four intermediaries were identified and they have modified the penicillinic structure, which is the moiety responsible for the antimicrobial activity. Additionally, the possible oxacillin sonodegradation mechanism was proposed based on the evolution of the by-products and their chemical structure. Furthermore, the high-frequency ultrasound action over 120 min readily removed oxacillin and eliminated its antimicrobial activity. However, the pollutant was not mineralized even after a long period of ultrasonic irradiation (360 min). Interestingly, the previously sonicated water containing oxacillin and both additives was completely mineralized using non-adapted microorganisms from a municipal wastewater treatment plant. These results show that the sonochemical treatment transformed the initial pollutant into substances that are biotreatable with a typical aerobic biological system. PMID:26964950

  5. Decolouration of H2SO4 leachate from phosphorus-saturated alum sludge using H2O2 and advanced oxidation processes in phosphorus recovery strategy

    OpenAIRE

    Zhao, X. H.; Zhao, Y. Q.

    2009-01-01

    As a part of attempt for phosphorus (P) recovery from P-saturated alum sludge, which was used as a low-cost P-adsorbent in treatment reed bed for wastewater treatment, decolouration of H2SO4 leachate obtained from previous experiment, possessing a great deal of P, aluminum and red-brown coloured materials (RBCMs), by using H2O2 and advanced oxidation processes (AOPs) was investigated. The use of H2O2 and AOPs in the forms of Fenton (H2O2/Fe2+) and photo-Fenton (UV/H2O2/Fe2+) were tested. The ...

  6. The Effect of H2O2 Interference in Chemical Oxygen Demand Removal During Advanced Oxidation Processes

    Directory of Open Access Journals (Sweden)

    Afsane Chavoshani

    2016-07-01

    Full Text Available Hydrogen peroxide (H2O2 is one of the most oxidants in AOPs. By H2O2 dissociation, hydroxyl radical with a standard oxidation potential of 2.7 is produced. It is reported H2O¬ residual in AOPs has been led to interference in chemical oxygen demand (COD test and it is able to hinder biological treatment of waste water. Because of high mixed organic load of solid waste leachate, this study investigated effect of H2O2 interference in COD removal from solid waste leachate. In this study effect of parameters such as pH (3,5,7,12, H2O2 dose (0.01, 0.02, 0.03, 0.04 mol l-1, and time reaction(10,20,30,40,50,60 min evaluated on H2O2 interference in COD removal from solid waste leachate. Optimum pH and concentration were 3 and 0.02 moll-1 respectively. With increasing reaction time, COD removal was increased. The false COD obtained between 0.49mg per 1mg of H2O2. The average of COD removal by H2O2 for 60 min was 6.57%. Also reaction rate of this process was 0.0029 min-1. The presence of H2O2 leads to overestimation of COD values after reaction time because it consumes the oxidation agent. The extent of H2O2 interference in COD analysis was proportional to the remaining H2O2 concentration at the moment of sampling.

  7. UV-based advanced oxidation processes for the treatment of odour compounds: efficiency and by-product formation.

    Science.gov (United States)

    Zoschke, Kristin; Dietrich, Norman; Börnick, Hilmar; Worch, Eckhard

    2012-10-15

    The occurrence of the taste and odour compounds geosmin and 2-methyl isoborneol (2-MIB) affects the organoleptic quality of raw waters from drinking water reservoirs worldwide. UV-based oxidation processes for the removal of these substances are an alternative to adsorption and biological processes, since they additionally provide disinfection of the raw water. We could show that the concentration of geosmin and 2-MIB could be reduced by VUV irradiation and the combination of UV irradiation with ozone and hydrogen peroxide in pure water and water from a drinking water reservoir. The figure of merit EE/O is an appropriate tool to compare the AOPs and showed that VUV and UV/O(3) yielded the lowest treatment costs for the odour compounds in pure and raw water, respectively. Additionally, VUV irradiation with addition of ozone, generated by the VUV lamp, was evaluated. The generation of ozone and the irradiation were performed in a single reactor system using the same low-pressure mercury lamp, thereby reducing the energy consumption of the treatment process. The formation of the undesired by-products nitrite and bromate was investigated. The combination of VUV irradiation with ozone produced by a VUV lamp avoided the formation of relevant concentrations of the by-products. The internal generation of ozone is capable to produce ozone concentrations sufficient to reduce EE/O below 1 kWh m(-3) and without the risk of the formation of nitrite or bromate above the maximum contaminant level. PMID:22858230

  8. Photodegradation of emerging micropollutants using the medium-pressure UV/H2O2 Advanced Oxidation Process.

    Science.gov (United States)

    Shu, Zengquan; Bolton, James R; Belosevic, Miodrag; El Din, Mohamed Gamal

    2013-05-15

    A medium-pressure (MP) ultraviolet (UV) process has been applied to investigate the direct UV photolysis and UV/H2O2 oxidation of selected model micropollutants (naproxen, carbamazepine, diclofenac, gemfibrozil, ibuprofen, caffeine, 2,4-D, 2,4-DCP, and mecoprop). The quantum yields were found to be between 0.0010 and 0.13 at pH = 7. In the MP UV/H2O2 oxidation, the pseudo first-order rate constants for the selected compounds were found to be dependent on their initial concentrations (at mg/L levels) and on the H2O2 concentration. The UV doses required for 50% and 90% removal at various H2O2 levels varied widely among the compounds tested. Second-order rate constants (ranging from 4.1 × 10(9) to 1.4 × 10(10) M(-1) s(-1)) for the reaction between the selected compounds and hydroxyl radicals were determined using a competition-kinetics approach, where para-chlorobenzoic acid (pCBA) was chosen as the reference compound. Further, as an evaluation of electrical energy efficiency, the Figure-of-Merit, Electrical Energy per Order (EEO) was determined for the selected compounds using a batch reactor at 25 and 50 mg/L H2O2 concentrations. The electrical energy (in kWh) required to reduce a pollutant concentration by 90% ranged from 1.3 to 7.1 kWh m(-3). PMID:23517874

  9. Advanced Oxidation of the Endosulfan and Profenofos in Aqueous Solution Using UV/H2O22 Process

    Directory of Open Access Journals (Sweden)

    Mohammad Mehdi Amin

    2014-01-01

    Full Text Available Degradation of two pesticides, endosulfan and profenofos, was investigated in aqueous solution using a combination of ultraviolet (UV light and hydrogen peroxide (H2O2. Photochemical experiments based on the L9 (34 three-level orthogonal array of the Taguchi method with four control factors including initial pesticide concentrations (10, 15 and 20 mg/l, UV irradiation times (30, 60 and 90 min, pH (5, 6.5 and 8 and H2O2 (0.1, 0.01 and 0.05 M were conducted. The endosulfan and profenofos were analyzed using gas chromatography with electron capture detector (ECD and gas chromatography with mass spectrometry (GC-MS respectively. Under the optimum conditions, 96.5% of the endosulfan and 98.5% of the profenofos were removed in about 90 min. The study also showed that the oxidation rate was enhanced more during the UV/H2O2 process in comparison to direct photolysis. The results of our study suggested that the concentration of 0.1 molar H2O2 and 10 ppm of pesticide in the solution at pH 8 with 90 min UV irradiation time were the optimal conditions for the photochemical degradation of two pesticides. The photochemical degradation with UV/H2O2 can be an efficient method to remove the endosulfan and profenofos from aqueous solution.

  10. Evaluation of a UV-light emitting diodes unit for the removal of micropollutants in water for low energy advanced oxidation processes.

    Science.gov (United States)

    Autin, Olivier; Romelot, Christophe; Rust, Lena; Hart, Julie; Jarvis, Peter; MacAdam, Jitka; Parsons, Simon A; Jefferson, Bruce

    2013-07-01

    There is growing interest in using light emitting diodes (LEDs) as alternative to traditional mercury lamps for the removal of micropollutants by advanced oxidation processes due to their low energy consumption and potential for high efficiency and long lifetime. This study investigates the penetration and coverage of the light emitted by LEDs in order to build an optimised LED collimated beam apparatus. From the experimental data, cost analysis was conducted in order to identify when LEDs will become economically viable. It was observed that if their development follows the predictions, LEDs should be a viable alternative to traditional lamps within 7yr for both UV/H2O2 and UV/TiO2 processes. However, parameters such as wall plug efficiency and input power need to improve for LEDs to become competitive. PMID:23668964

  11. Comparison of the efficiency of *OH radical formation during ozonation and the advanced oxidation processes O3/H2O2 and UV/H2O2.

    Science.gov (United States)

    Rosenfeldt, Erik J; Linden, Karl G; Canonica, Silvio; von Gunten, Urs

    2006-12-01

    Comparison of advanced oxidation processes (AOPs) can be difficult due to physical and chemical differences in the fundamental processes used to produce OH radicals. This study compares the ability of several AOPs, including ozone, ozone+H2O2, low pressure UV (LP)+H2O2, and medium pressure UV (MP)+H2O2 in terms of energy required to produce OH radicals. Bench scale OH radical formation data was generated for each AOP using para-chlorobenzoic acid (pCBA) as an OH radical probe compound in three waters, Lake Greifensee water, Lake Zurich water, and a simulated groundwater. Ozone-based AOPs were found to be more energy efficient than the UV/H2O2 process at all H2O2 levels, and the addition of H2O2 in equimolar concentration resulted in 35% greater energy consumption over the ozone only process. Interestingly, the relatively high UV/AOP operational costs were due almost exclusively to the cost of hydrogen peroxide while the UV portion of the UV/AOP process typically accounted for less than 10 percent of the UV/AOP cost and was always less than the ozone energy cost. As the *OH radical exposure increased, the energy gap between UV/H2O2 AOP and ozone processes decreased, becoming negligible in some water quality scenarios. PMID:17078993

  12. Advanced oxidation processes for treatment of petroleum refinery sour waters; Processos oxidativos avancados para tratamento de aguas acidas de refinaria de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Antonio V.; Coelho, Alessandra D.; Sant' Anna Junior, Geraldo L.; Dezotti, Marcia [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Programa de Engenharia Quimica

    2004-07-01

    The characteristics of the waste water generated by the petroleum refineries are related to the type and amount of processed oil, to the nature and the efficiency of the refining operation. The effluents are composed basically of oily waters, originating from of the contact with the oil. Among them, the current of sour water is one of the most preoccupying due to its composition: sulfide, ammonia, mercaptans, phenol, dissolved oil, basic pH, dissolved organic carbon (DOC) and chemical oxygen demand (COD) high. The aim of this work was to evaluate the advanced oxidation processes to degrade sour water (UV radiation, H{sub 2}O{sub 2} and H{sub 2}O{sub 2}/UV, photocatalysis, Fenton and photo-Fenton). All process, except Fenton and photo-Fenton, did not supply satisfactory results, reducing 25% of initial DOC, which it is of 450 mg/L. The results using the Fenton process reached removal of 50% of the initial COD, and when photo- Fenton process obtaining removal of 90%. The processes Fenton and photo-Fenton were shown capable to degrade this kind of waste water, minimizing the environmental problems and corrosion, operating as a pre-treatment for the biological system, or acting alone to degrade the organic matter contained, seeking the water reuse. The effluent used in this work came from Duque de Caxias Refinery (Reduc)/PETROBRAS. (author)

  13. Post-treatment of biologically treated wastewater containing organic contaminants using a sequence of H2O2 based advanced oxidation processes: photolysis and catalytic wet oxidation.

    Science.gov (United States)

    Rueda-Márquez, J J; Sillanpää, M; Pocostales, P; Acevedo, A; Manzano, M A

    2015-03-15

    In this paper the feasibility of a multi-barrier treatment (MBT) for the regeneration of synthetic industrial wastewater (SIWW) was evaluated. Industrial pollutants (orange II, phenol, 4-chlorophenol and phenanthrene) were added to the effluent of municipal wastewater treatment plant. The proposed MBT begins with a microfiltration membrane pretreatment (MF), followed by hydrogen peroxide photolysis (H2O2/UVC) and finishing, as a polishing step, with catalytic wet peroxide oxidation (CWPO) using granular activated carbon (GAC) at ambient conditions. During the microfiltration step (0.7 μm) the decrease of suspended solids concentration, turbidity and Escherichia coli in treated water were 88, 94 and 99%, respectively. Also, the effluent's transmittance (254 nm) was increased by 14.7%. Removal of more than 99.9% of all added pollutants, mineralization of 63% of organic compounds and complete disinfection of total coliforms were reached during the H2O2/UVC treatment step (H2O2:TOC w/w ratio = 5 and an UVC average dose accumulated by wastewater 8.80 WUVC s cm(-2)). The power and efficiency of the lamp, the water transmittance and photoreactor geometry are taken into account and a new equation to estimate the accumulated dose in water is suggested. Remaining organic pollutants with a higher oxidation state of carbon atoms (+0.47) and toxic concentration of residual H2O2 were present in the effluent of the H2O2/UVC process. After 2.3 min of contact time with GAC at CWPO step, 90 and 100% of total organic carbon and residual H2O2 were removed, respectively. Also, the wastewater toxicity was studied using Vibrio fischeri and Sparus aurata larvae. The MBT operational and maintenance costs (O&M) was estimated to be 0.59 € m(-3). PMID:25600300

  14. The feasibility of using combined TiO2 photocatalysis oxidation and MBBR process for advanced treatment of biologically pretreated coal gasification wastewater.

    Science.gov (United States)

    Xu, Peng; Han, Hongjun; Hou, Baolin; Zhuang, Haifeng; Jia, Shengyong; Wang, Dexin; Li, Kun; Zhao, Qian

    2015-01-01

    The study examined the feasibility of using combined heterogeneous photocatalysis oxidation (HPO) and moving bed biofilm reactor (MBBR) process for advanced treatment of biologically pretreated coal gasification wastewater (CGW). The results indicated that the TOC removal efficiency was significantly improved in HPO. Gas chromatography-mass spectrometry (GC-MS) analysis indicated that the HPO could be employed to eliminate bio-refractory and toxic compounds. Meanwhile, the BOD5/COD of the raw wastewater was increased from 0.08 to 0.49. Furthermore, in the integration of TiO2 photocatalysis oxidation and MBBR process, the effluent of COD, BOD5, TOC, NH4(+)-N and TN were 22.1 mg/L, 1.1 mg/L, 11.8 mg/L, 4.1mg/L and 13.7 mg/L, respectively, which all met class-I criteria of the Integrated Wastewater Discharge Standard (GB18918-2002, China). The total operating cost was 2.8CNY/t. Therefore, there is great potential for the combined system in engineering applications as a final treatment for biologically pretreated CGW. PMID:25934578

  15. Evaluation of Efficacy of Advanced Oxidation Processes Fenton, Fenton-like and Photo-Fenton for Removal of Phenol from Aqueous Solutions

    International Nuclear Information System (INIS)

    Contamination of water, soil and groundwater caused by aromatic compounds induces great concern in most world areas. Among organic pollutants, phenol is mostly considered dangerous due to its high toxicity for human and animal. Advanced oxidation processes (AOPs) is considered as a most efficient method also the best one for purifying organic compounds which are resistant to conventional physical and chemical processes. This experimental study was carried out in laboratory scale. First, a synthetic solution was made of phenol. Then, Fenton, Fenton-like and photo-Fenton processes were applied removing phenol from aquatic solution. The effects of Hydrogen Peroxide concentration, catalyst, pH and time were studied to phenol removal efficiency. Results showed that Photo-Fenton process with removal efficiency (97.5 percentage) is more efficient than Fenton and Fenton-like processes with removal efficiency (78.7 percentage and 82.5 percentage respectively), in pH=3, (H/sub 2/O/sub 2/)= 3mM, (Fe2+)= 0.1 mM, phenol concentration 100 mg L-1 and time reaction 60 min, the phenol removal was 97.5 percentage. (author)

  16. Advances in Solidification Processing

    Directory of Open Access Journals (Sweden)

    Hugo F. Lopez

    2015-08-01

    Full Text Available Melt solidification is the shortest and most viable route to obtain components, starting from the design to the finished products. Hence, a sound knowledge of the solidification of metallic materials is essential for the development of advanced structural metallic components that drive modern technological societies. As a result, there have been innumerable efforts and full conferences dedicated to this important subject [1–6]. In addition, there are various scientific journals fully devoted to investigating the various aspects which give rise to various solidification microstructures [7–9]. [...

  17. Recuperação de sílica-gel utilizando processos oxidativos avançados: uma alternativa simples e de baixo custo Silica gel recycling using and advanced oxidative process: a simple and low-cost alternative

    OpenAIRE

    Silvio César Godinho Teixeira; Leda Mathias; Maria Cristina Canela

    2003-01-01

    Silica gel is widely used as adsorbent for isolating and purifying natural compounds. Intensive use and high cost make this process expensive and generate solid residues contaminated with many different organic compounds. In the present work a simple method for recycling silica was investigated, by using Advanced Oxidative Processes. Silica gel was treated with H2O2/solar light and compared with a sample treated by conventional methods (high temperature and oxidation with KMnO4). High tempera...

  18. Decolouration of H2SO4 leachate from phosphorus-saturated alum sludge using H2O2 and advanced oxidation processes in phosphorus recovery strategy.

    Science.gov (United States)

    Zhao, X H; Zhao, Y Q

    2009-12-01

    As a part of attempt for phosphorus (P) recovery from P-saturated alum sludge, which was used as a low-cost P-adsorbent in treatment reed bed for wastewater treatment, decolouration of H(2)SO(4) leachate obtained from previous experiment, possessing a great deal of P, aluminum and red-brown coloured materials (RBCMs), by using H(2)O(2) and advanced oxidation processes (AOPs) was investigated. The use of H(2)O(2) and AOPs in the forms of Fenton (H(2)O(2)/Fe(2 +)) and photo-Fenton (UV/H(2)O(2)/Fe(2 +)) were tested. The changes in colour and total organic carbon (TOC) were taken place as a result of mineralization of RBCMs. The results revealed that all of these three processes examined were efficient. It was found that about 98% colour and 47% TOC can be removed under photo-Fenton treatment after 8 hours of UV irradiation.Correspondingly, the reaction rates of H(2)O(2) and Fenton systems were slow, but 100% colour and 59% TOC removal of H(2)O(2) process and 100% colour and 67% TOC reductions of Fenton process can be achieved after 72 hours of reaction. The changes of structure and molecular weight/size of RBCMs were also evaluated by HPLC and UV-vis spectroscopic analysis. From the results, some chromophores of RBCMs such as aromatic groups were appeared to be easily degraded to the smaller refractory components. Hence, based on the experimental results and considering the investment and expediency of operation, H(2)O(2) and Fenton oxidation could be suitable technologies for the treatment of the RBCMs derived from P-extraction stage by using H(2)SO(4) leaching. PMID:20183514

  19. Micropollutant degradation, bacterial inactivation and regrowth risk in wastewater effluents: Influence of the secondary (pre)treatment on the efficiency of Advanced Oxidation Processes.

    Science.gov (United States)

    Giannakis, Stefanos; Voumard, Margaux; Grandjean, Dominique; Magnet, Anoys; De Alencastro, Luiz Felippe; Pulgarin, César

    2016-10-01

    In this work, disinfection by 5 Advanced Oxidation Processes was preceded by 3 different secondary treatment systems present in the wastewater treatment plant of Vidy, Lausanne (Switzerland). 5 AOPs after two biological treatment methods (conventional activated sludge and moving bed bioreactor) and a physiochemical process (coagulation-flocculation) were tested in laboratory scale. The dependence among AOPs efficiency and secondary (pre)treatment was estimated by following the bacterial concentration i) before secondary treatment, ii) after the different secondary treatment methods and iii) after the various AOPs. Disinfection and post-treatment bacterial regrowth were the evaluation indicators. The order of efficiency was Moving Bed Bioreactor > Activated Sludge > Coagulation-Flocculation > Primary Treatment. As far as the different AOPs are concerned, the disinfection kinetics were: UVC/H2O2 > UVC and solar photo-Fenton > Fenton or solar light. The contextualization and parallel study of microorganisms with the micropollutants of the effluents revealed that higher exposure times were necessary for complete degradation compared to microorganisms for the UV-based processes and inversed for the Fenton-related ones. Nevertheless, in the Fenton-related systems, the nominal 80% removal of micropollutants deriving from the Swiss legislation, often took place before the elimination of bacterial regrowth risk. PMID:27403873

  20. Advanced Oxidation Processes for removal of COD from pulp and paper mill effluents : A Technical, Economical and Environmental Evaluation

    OpenAIRE

    Karat, Irma

    2013-01-01

    In Sweden, the dominating source for emissions of degradable organic substances to water is the pulp and paper industry. The organic substances increase oxygen consumption in the recipient which subsequently threatens aquatic species. Improved process engineering, process closures and use of external treatments have in recent years drastically lowered the Biological Oxygen Demand (BOD). However, the Chemical Oxygen Demand (COD) has not been reduced to the same extent, as some organic substanc...

  1. Pretreatment of sugarcane bagasse using the advanced oxidation process by electron beam for enzymatic hydrolysis of cellulose

    International Nuclear Information System (INIS)

    The sugar cane bagasse is a renewable energy source and a raw material promise in the biofuel production, once represents about 30% of glucose contained in the plant with the potential to be hydrolyzed and then converted to ethanol. The bagasse is composed of cellulose, straight chain of glucose, of hemicellulose, an amorphous polymer consisting of xylose, arabinose, galactose, and mannose, and of lignin, a complex polymer consisting of fenilpropan units that acts as waterproof coating on the fibers, which is hard to remove due its recalcitrant nature. The aim of this work was to study the electron beam processing as a pretreatment of sugarcane bagasse to enzymatic hydrolysis of cellulose. The pretreatment of sugarcane bagasse is one of the most important steps to make this material economically viable and competitive on the energy production. As a pretreatment the electron beam processing can weak the hemicellulose and lignin structures by the action highly reactive radicals that breaks the links, reducing the degree of polymerization fibers. It was evaluated the chemical and structural modifications on fibers caused by the irradiation, the enzymatic hydrolysis of electron beam as the only pretreatment and combined to steam explosion. For enzymatic hydrolysis it was used the commercial enzymes from Novozymes. The radiation processing promotes changes in structure and composition of sugarcane bagasse, increasing the solubility, that is related to hemicellulose and cellulose cleavage, and also increasing the enzymatic conversion yield. In the case of exploded bagasse there is no changes in the enzymatic hydrolysis yield, however the electron beam processing promoted a 67% reduction of furfural, that is formed in the steam explosion process. (author)

  2. Oxidation of advanced steam turbine alloys

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, G.R.; Covino, B.S., Jr.; Bullard, S.J.; Ziomek-Moroz, M.

    2006-03-01

    Advanced or ultra supercritical (USC) steam power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy’s Advanced Power Systems Initiatives include coal generation at 60% efficiency, which would require steam temperatures of up to 760°C. This research examines the steamside oxidation of advanced alloys for use in USC systems, with emphasis placed on alloys for high- and intermediate-pressure turbine sections.

  3. Life Cycle Assessment as a tool for green Chemistry: Application to different advanced oxidation processes for wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Munoz Ortiz, I.; Domenech Antunez, X.; Malato Rodriguez, S.

    2006-07-01

    The development of chemistry during the twentieth century has changed our lives. In fact, chemistry and chemicals surrounds US in our daily activities, due to the huge supply of products aimed at improving our quality of life. Chemistry has resulted in the medical revolution of the past century, in which drugs as antibiotics have been used to cure diseases that affected mankind for centuries. These advances have led to the rise in the average life expectancy from 47 in 1900, to 75 years in the 1990s (Breslow 1997). On the other hand, the world's food supply has seen an explosive expansion because of the development of pesticides as well as fertilisers that protect crops and improve their productivity. Other common chemicals are those related to hygiene, such as soaps, detergents, disinfectants, toothpaste, etc. Therefore, there is practically no facet in material life-transportation communication, clothing, shelter, office- in which chemistry does not play an important role, either to supply consumer products or to improve services addressed to society in general (Domenech 2005). In spite of all these clear benefits, the chemical industry is often viewed by the general public as causing more harm than good (Lancaster 2002). A major reason for this is that the industry is perceived as being polluting and causing significant environmental damage. Indeed, the manufacture, use and disposal of chemicals consume large amounts of resources, and originates emissions of pollutants to all environmental compartments, not to mention the numerous accidents and disasters in which the chemical industry has been involved in the recent past. (Author)

  4. Treatment of urban river contaminated sediment with ex situ advanced oxidation processes: technical feasibility, environmental discharges and cost-performance analysis.

    Science.gov (United States)

    Yan, Dickson Y S; Liu, Tongzhou; Lo, Irene M C

    2015-01-01

    The technical feasibility, environmental discharges and cost-performance of urban river contaminated sediment treatment with ex situ advanced oxidation processes were evaluated for the purpose of achieving an ideal treatment goal (for marine disposal) and a cost-performance treatment goal (for beneficially reusing as a filling material). Sediment samples were collected from a river located in southern China. To achieve the ideal treatment goal, sequential treatments (Fenton's reaction+activated persulphate oxidation) were carried out. One-step Fenton's reaction was applied to achieve the cost-performance treatment goal. The resulting effluent was treated and discharged, and sludge generated in wastewater treatment was characterized. The resources input throughout the treatment processes were recorded for cost estimation. After the treatment designed for achieving the ideal treatment goal, most pollutants fulfilled the treatment goal except Pb, Cd, Hg and Ag, probably because these four metals were present mainly in stable fractions of the sediment. The cost-performance treatment goal was achieved in view of low pollutant contents in the toxicity characteristic leaching procedure leachate of treated sediment. The cost for achieving the cost-performance treatment goal is much less than that for achieving the ideal treatment goal. The major cost difference is attributed to chemical cost. Stringent sediment treatment goals based on existing standards would lead to massive chemical use, complex treatment and hence huge cost. A simpler treatment with fewer chemicals is adequate for sediment beneficially reused as a filling material, and is economically more advantageous than handling sediment for marine disposal. PMID:25687695

  5. Evaluation of advanced oxidative processes in contaminated soil of the Pernambuco state; Avaliacao dos processos oxidativos avancados num solo contaminado do estado de Pernambuco

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Paula T.S. e [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Quimica; Santos, Suenia S. [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Engenharia Quimica; Barros Neto, Benicio de [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Quimica Fundamental; Dorea, Haroldo S. [Universidade Federal de Sergipe (UFS), Aracaju, SE (Brazil); Motta Sobrinho, Mauricio A. da; Silva, Valdinete L. da [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

    2004-07-01

    In this work were used the following techniques of advanced oxidative processes: hydrogen peroxide, Fenton reagent and heterogeneous photocatalysis (TiO2). These processes have shown as an alternative technology to the treatment of some environmental matrices. The soil studied was contaminated by an oil mixture proceeding from an emptying in the patio of an industry of the state of Pernambuco. This soil has about 14,5 g/Kg of total organic carbon and 3400 mg/kg of TPH. Two planning factorial 23 were composed: one in relation to hydrogen peroxide and the other to titanium dioxide, in order to find the best conditions for the contaminant degradation. The variables and the studied levels for the former was: FeSO4 - 0,18 M (without, 4 and 8 ml); Adjustment of pH (3, without, without); Time of exposition to the sun (8h, 12h, 16h). The volumes of used peroxide in the assays were 80 and 40 ml. In relation to the second planning, were studied the following conditions: TiO2 (g) (without,5;0,75;1,0), volume H2O (0, 2,5 and 5 ml) and time of exposition to the sun (8, 40, 72h). In relation to the first planning a destruction of 84% of the oil was achieved. However, in relation to 2nd the planning non-significant degradation was obtained, and to study other conditions ought to be investigated. (author)

  6. Advanced methods for processing ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Carter, W.B. [Georgia Institute of Technology, Atlanta, GA (United States)

    1997-04-01

    Combustion chemical vapor deposition (combustion CVD) is being developed for the deposition of high temperature oxide coatings. The process is being evaluated as an alternative to more capital intensive conventional coating processes. The thrusts during this reporting period were the development of the combustion CVD process for depositing lanthanum monazite, the determination of the influence of aerosol size on coating morphology, the incorporation of combustion CVD coatings into thermal barrier coatings (TBCs) and related oxidation research, and continued work on the deposition of zirconia-yttria coatings.

  7. Partial oxidation process

    International Nuclear Information System (INIS)

    A process is described for the production of gaseous mixtures comprising H/sub 2/+CO comprising: (1) mixing an ash fusion temperature reducing agent comprising a comminuted ore having a particle size of ASTM E-11 Standard Sieve Designation in the range of about 0.1-210 microns with at least one material selected from the group consisting of a pumpable ash-containing liquid hydrocarbonaceous material and ash-containing petroleum coke. The ash from the liquid hydrocarbonaceous material or petroleum coke principally comprises the oxides of Ni, V, and Fe along with a minor amount of the oxides selected from the group consisting of Si, Al, Ca, Ti, Cr, and mixtures thereof. The weight ratio of ash fusion temperature reducing agent to ash produced in (2) is in the range of about 0.5 to 10. The comminuted ash fusion temperature reducing agent principally comprises monoclinic amphibole and/or pyroxene minerals in which the following elements are present principally as silicate compounds in weight percent (basis ore): iron in the range of about 5-55, calcium in the range of about 1-10, silicon in the range of about 4-25, magnesium in the range of about 1-10, and aluminum in the range of about 0.25-5.0; and (2) reacting the mixture from (1) at a temperature in the range of about 21000F to 27000F and a pressure in the range of about 1 to 200 atmospheres in a free-flow refractory lined partial oxidation reaction zone with a free-oxygen containing gas

  8. Treatment of an actual slaughterhouse wastewater by integration of biological and advanced oxidation processes: Modeling, optimization, and cost-effectiveness analysis.

    Science.gov (United States)

    Bustillo-Lecompte, Ciro Fernando; Mehrvar, Mehrab

    2016-11-01

    Biological and advanced oxidation processes are combined to treat an actual slaughterhouse wastewater (SWW) by a sequence of an anaerobic baffled reactor, an aerobic activated sludge reactor, and a UV/H2O2 photoreactor with recycle in continuous mode at laboratory scale. In the first part of this study, quadratic modeling along with response surface methodology are used for the statistical analysis and optimization of the combined process. The effects of the influent total organic carbon (TOC) concentration, the flow rate, the pH, the inlet H2O2 concentration, and their interaction on the overall treatment efficiency, CH4 yield, and H2O2 residual in the effluent of the photoreactor are investigated. The models are validated at different operating conditions using experimental data. Maximum TOC and total nitrogen (TN) removals of 91.29 and 86.05%, respectively, maximum CH4 yield of 55.72%, and minimum H2O2 residual of 1.45% in the photoreactor effluent were found at optimal operating conditions. In the second part of this study, continuous distribution kinetics is applied to establish a mathematical model for the degradation of SWW as a function of time. The agreement between model predictions and experimental values indicates that the proposed model could describe the performance of the combined anaerobic-aerobic-UV/H2O2 processes for the treatment of SWW. In the final part of the study, the optimized combined anaerobic-aerobic-UV/H2O2 processes with recycle were evaluated using a cost-effectiveness analysis to minimize the retention time, the electrical energy consumption, and the overall incurred treatment costs required for the efficient treatment of slaughterhouse wastewater effluents. PMID:27568982

  9. The kinetics of activation and deactivation in the process of water ozonising used for advanced oxidation of the dust waste from moulding sands

    Directory of Open Access Journals (Sweden)

    A. Baliński

    2009-01-01

    Full Text Available Adding coal dust and organic carriers of the lustrous carbon to bentonite-bonded moulding sands in amounts justified by thetechnological regime and the use of cores and protective coatings based on organic compounds create serious threats to the environment.During thermal destruction of the individual components of moulding and core sands, some toxic organic compounds are emitted. They formthe majority of the Hazardous Air Pollutants (HAPs, and include mainly compounds like benzene, toluene, xylene, naphtalene, hexane,acetaldehyde, acrolein, aniline, cresol and cumene, their polycyclic derivatives, phenol, formaldehyde, and other similar matters. In thusformed dust waste, the amount of which constitutes about 20% of all the waste from foundries using traditional moulding and core sands, there are still full-value materials which can undergo total recycling, providing the HAPs are partially or totally removed from them. The article discusses some problems of the advanced oxidation of selected toxic chemical compounds present in bentonite-bonded moulding sands due to the effect of high temperature. The results of the investigations of the kinetics of the process of maximum water saturation with ozone (acting as an oxidiser and of the kinetics of the natural process of ozone decomposition to diatomic oxygen were presented. It has been stated that the maximum time of water saturation with ozone using an OZOMATIC OSC-MODULAR 4HC ozone generator and a 1m3 capacity tank with water is 60 minutes. After 30 minute break in the ozonising process, the ozone concentration in water decreases by 40 to 50%. To obtain maximum ozone concentration in water during the next ozonising cycle, it is necessary to have the ozone-generating device running for the next 30 minutes. The stabilisation of ozone concentration in water takes place only after the third ozonising cycle, when it reaches nearly 80%of the maximum value obtained after the first process cycle

  10. Test Concept for Advanced Oxidation Techniques

    DEFF Research Database (Denmark)

    Bennedsen, Lars Rønn; Søgaard, Erik Gydesen; Mortensen, Lars

    as establishing the applicability of the proposed technique, the treatability tests also provide essential site-specific design parameters required for the full scale system, namely; oxidant demand, delivery method, kinetics etc. Drawing up field studies and laboratory data, this poster will discus the importance...... advanced on-site oxidation tests. The remediation techniques included are electrochemical oxidation, photochemical/photocatalytic oxidation, ozone, hydrogen peroxide, permanganate, and persulfate among others. A versatile construction of the mobile test unit makes it possible to combine different...

  11. The fate of H2O2 during managed aquifer recharge: A residual from advanced oxidation processes for drinking water production.

    Science.gov (United States)

    Wang, F; van Halem, D; van der Hoek, J P

    2016-04-01

    The fate of H2O2 residual from advanced oxidation process (AOP) preceding managed aquifer recharge (MAR) is of concern because H2O2 could lead to undesired effects on organisms in the MAR aquatic and soil ecosystem. The objective of this study was to distinguish between factors affecting H2O2 decomposition in MAR systems, simulated in batch reactors with synthetic MAR water and slow sand filter sand. The results showed that pure sand and soil organic matter had no considerable effect on H2O2 decomposition, whereas naturally occurring inorganic substances on the surface of sand grains and microbial biomass are the two main factors accelerating H2O2 decomposition in MAR systems. Additionally, the results showed that the H2O2 decompositions with different initial concentrations fitted first-order kinetics in 2-6 h in a mixture of slow sand filter sand (as a substitute for sand from a MAR system) and synthetic MAR water with high bacterial population. An estimation indicated that low concentrations of H2O2 (<3 mg/L) could decompose to the provisional standard of 0.25 mg/L in the first centimeters of MAR systems with the influent water containing high microbial biomass 38 ng ATP/mL. PMID:26812369

  12. Treatment of Remazol Brilliant Blue Dye Effluent by Advanced Photo Oxidation Process in TiO2/UV and H2O2/UV reactors

    Directory of Open Access Journals (Sweden)

    M. Verma

    2008-01-01

    Full Text Available Advanced oxidation processes involving TiO2/UV and H2O2/UV were evaluated for their potential use in decolorization of textile dye effluents. A coil photo reactor, consisting of UV radiation source and a spiral coil coated with TiO2, was used to treat synthetic effluent of Remazol Brilliant Blue dye. The TiO2 coating was performed using the sol-gel technique. The effects of UV radiation, TiO2 coatings and dye concentration were studied and the results were compared to dye treatment involving H2O2. The maximum dye removal efficiencies were 7.3, 12.2 and 12.5 % for uncoated, single coat and dual coat of TiO2, respectively. The decolorization efficiency was inversely related to dye concentration of the effluent. The treatments with UV only, TiO2 only, UV+TiO2, H2O2 only and UV+H2O2 resulted in color reduction of 7.6, 2.3, 12.5, 4.1 and 99.9 % respectively. The maximum decolorization occurred in ≤ 100 min in all cases. The temperature varied from 29.2 to 54.7°C for UV+TiO2 treatment and no change in reactor temperature was observed when UV was not used.

  13. Response surface method for the optimisation of micropollutant removal in municipal wastewater treatment plant effluent with the UV/H2O2 advanced oxidation process.

    Science.gov (United States)

    Schulze-Hennings, U; Pinnekamp, J

    2013-01-01

    Experiments with the ultraviolet (UV)/H2O2 advanced oxidation process (AOP) were conducted to investigate the abatement of micropollutants in wastewater treatment plant effluent. The fluence and the starting concentration of H2O2 in a bench-scale batch reactor were varied according to response surface method (RSM) to examine their influence on the treatment efficiency. It was shown that the investigated AOP is very effective for the abatement of micropollutants with conversion rates typically higher than 90%. Empirical relationships between fluence, H2O2 dosage and the resulting concentration of micropollutants were established by RSM. By this means it was shown that X-ray-contrast media had been degraded only by UV light. Nevertheless, most substances were degraded by the combination of UV irradiation and H2O2. Based on RSM an optimisation of multiple responses was conducted to find the minimal fluence and H2O2 dosage that are needed to reach an efficient abatement of micropollutants. PMID:23656952

  14. Oxidation of alloys for advanced steam turbines

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R.; Covino, Bernard S., Jr.; Bullard, Sophie J.; Ziomek-Moroz, M.; Alman, David E.

    2005-01-01

    Ultra supercritical (USC) power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy’s Advanced Power Systems Initiatives include coal generation at 60% efficiency, which would require steam temperatures of up to 760°C. This research examines the steamside oxidation of advanced alloys for use in USC systems, with emphasis placed on alloys for high- and intermediate-pressure turbine sections.

  15. An overview on the advanced oxidation processes applied for the treatment of water pollutants defined in the recently launched Directive 2013/39/EU.

    Science.gov (United States)

    Ribeiro, Ana R; Nunes, Olga C; Pereira, Manuel F R; Silva, Adrián M T

    2015-02-01

    Environmental pollution is a recognized issue of major concern since a wide range of contaminants has been found in aquatic environment at ngL(-1) to μgL(-1) levels. In the year 2000, a strategy was defined to identify the priority substances concerning aquatic ecosystems, followed by the definition of environmental quality standards (EQS) in 2008. Recently it was launched the Directive 2013/39/EU that updates the water framework policy highlighting the need to develop new water treatment technologies to deal with such problem. This review summarizes the data published in the last decade regarding the application of advanced oxidation processes (AOPs) to treat priority compounds and certain other pollutants defined in this Directive, excluding the inorganic species (cadmium, lead, mercury, nickel and their derivatives). The Directive 2013/39/EU includes several pesticides (aldrin, dichlorodiphenyltrichloroethane, dicofol, dieldrin, endrin, endosulfan, isodrin, heptachlor, lindane, pentachlorophenol, chlorpyrifos, chlorfenvinphos, dichlorvos, atrazine, simazine, terbutryn, diuron, isoproturon, trifluralin, cypermethrin, alachlor), solvents (dichloromethane, dichloroethane, trichloromethane and carbon tetrachloride), perfluorooctane sulfonic acid and its derivatives (PFOS), polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), nonylphenol and octylphenol, as well as the three compounds included in the recommendation for the first watch list of substances (diclofenac, 17-alpha-ethinylestradiol (EE2) and 17-beta-estradiol (E2)). Some particular pesticides (aclonifen, bifenox, cybutryne, quinoxyfen), organotin compounds (tributyltin), dioxins and dioxin-like compounds, brominated diphenylethers, hexabromocyclododecanes and di(2-ethylhexyl)phthalate are also defined in this Directive, but studies dealing with AOPs are missing. AOPs are recognized tools to destroy recalcitrant compounds or, at least, to transform them into biodegradable species

  16. Mobil pilot unit of the advanced oxidation process for waste water treatment and reuse of the hydrics effluents; Unidade piloto movel de processo oxidativo avancado aplicado a tratamento e reuso de efluentes hidricos

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Lucia Maria Limoeiro; Pereira Junior, Oswaldo de Aquino; Henriques, Sheyla de Oliveira Carvalho; Jacinto Junior, Agenor [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    The chemical oxidation processes which generate free hydroxyl radicals are called Advanced Oxidation Process (AOP). These processes have been studied, in the last decades, as a new alternative for pollutants degradation. In the (AOP)'s there are in situ formation of hydroxyl radicals (OH{center_dot}), which are highly oxidant. Its high oxidation strength becomes it indicated in the treatment of effluent with highly refractory contaminants. It can be used as a partial treatment (taking the effluent to more degradable compounds), as a final treatment (taking the effluent to complete mineralization) or as a complementary treatment to other processes, allowing, for example, its reuse. The applicability of this technology in oily water effluents in all segments of the oil industry, has taken to the development, in the LARA (Laboratory of Treatment and Reuse of Waters - CENPES), of the Advanced Oxidation Process Mobile Pilot Unit (AOP's- MU) with capacity up to 1 m3/h. The (AOP's- MU) are able to produce hydroxyl radical from Fenton's reaction, titanium dioxide heterogeneous photo catalysis and hydrogen peroxide, photo-radiated or not. It is equipped with ultraviolet reactors of different wave lengths and power. (author)

  17. Microwave processing of ceramic oxide filaments

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, G.J.; Katz, J.D. [Los Alamos National Laboratory, NM (United States)

    1995-05-01

    The objective of the microwave filament processing project is to develop microwave techniques at 2.45 GHZ to manufacture continuous ceramic oxide filaments. Microwave processing uses the volumetric absorption of microwave power in oxide filament tows to drive off process solvents, to burn out organic binders, and to sinter the dried fibers to produce flexible, high-strength ceramic filaments. The technical goal is to advance filament processing technology by microwave heating more rapidly with less energy and at a lower cost than conventional processing, but with the same quality as conventional processing. The manufacturing goal is to collaborate with the 3M Company, a US manufacturer of ceramic oxide filaments, to evaluate the technology using a prototype filament system and to transfer the microwave technology to the 3M Company.

  18. Pilot-scale UV/H2O2 advanced oxidation process for municipal reuse water: Assessing micropollutant degradation and estrogenic impacts on goldfish (Carassius auratus L.).

    Science.gov (United States)

    Shu, Zengquan; Singh, Arvinder; Klamerth, Nikolaus; McPhedran, Kerry; Bolton, James R; Belosevic, Miodrag; Gamal El-Din, Mohamed

    2016-09-15

    Low concentrations (ng/L-μg/L) of emerging micropollutant contaminants in municipal wastewater treatment plant effluents affect the possibility to reuse these waters. Many of those micropollutants elicit endocrine disrupting effects in aquatic organisms resulting in an alteration of the endocrine system. A potential candidate for tertiary municipal wastewater treatment of these micropollutants is ultraviolet (UV)/hydrogen peroxide (H2O2) as an advanced oxidation process (AOP) which was currently applied to treat the secondary effluent of the Gold Bar Wastewater Treatment Plant (GBWWTP) in Edmonton, AB, Canada. A new approach is presented to predict the fluence-based degradation rate constants (kf') of environmentally occurring micropollutants including carbamazepine [(0.87-1.39) × 10(-3) cm(2)/mJ] and 2,4-Dichlorophenoxyacetic acid (2,4-D) [(0.60-0.91) × 10(-3) cm(2)/mJ for 2,4-D] in a medium pressure (MP) UV/H2O2 system based on a previous bench-scale investigation. Rather than using removal rates, this approach can be used to estimate the performance of the MP UV/H2O2 process for degrading trace contaminants of concern found in municipal wastewater. In addition to the ability to track contaminant removal/degradation, evaluation of the MP UV/H2O2 process was also accomplished by identifying critical ecotoxicological endpoints (i.e., estrogenicity) of the treated wastewater. Using quantitative PCR, mRNA levels of estrogen-responsive (ER) genes ERα1, ERα2, ERβ1, ERβ2 and NPR as well as two aromatase encoding genes (CYP19a and CYP19b) in goldfish (Carassius auratus L.) were measured during exposure to the GBWWTP effluent before and after MP UV/H2O2 treatment (a fluence of 1000 mJ/cm(2) and 20 mg/L of H2O2) in spring, summer and fall. Elevated expression of estrogen-responsive genes in goldfish exposed to UV/H2O2 treated effluent (a 7-day exposure) suggested that the UV/H2O2 process may induce acute estrogenic disruption to goldfish principally because

  19. Review of iron-free Fenton-like systems for activating H{sub 2}O{sub 2} in advanced oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Bokare, Alok D.; Choi, Wonyong, E-mail: wchoi@postech.edu

    2014-06-30

    Graphical abstract: - Highlights: • Elements with multiple redox states efficiently decompose H{sub 2}O{sub 2} at neutral pH. • Activation of H{sub 2}O{sub 2} is entirely governed by solution pH and catalyst composition. • Metal leaching and toxicity is an important factor for practical applications. • Iron-free Fenton systems work only in specialized reaction conditions. - Abstract: Iron-catalyzed hydrogen peroxide decomposition for in situ generation of hydroxyl radicals (HO{sup •} ) has been extensively developed as advanced oxidation processes (AOPs) for environmental applications. A variety of catalytic iron species constituting metal salts (in Fe{sup 2+} or Fe{sup 3+} form), metal oxides (e.g., Fe{sub 2}O{sub 3}, Fe{sub 3}O{sub 4}), and zero-valent metal (Fe{sup 0}) have been exploited for chemical (classical Fenton), photochemical (photo-Fenton) and electrochemical (electro-Fenton) degradation pathways. However, the requirement of strict acidic conditions to prevent iron precipitation still remains the bottleneck for iron-based AOPs. In this article, we present a thorough review of alternative non-iron Fenton catalysts and their reactivity towards hydrogen peroxide activation. Elements with multiple redox states (like chromium, cerium, copper, cobalt, manganese and ruthenium) all directly decompose H{sub 2}O{sub 2} into HO{sup •} through conventional Fenton-like pathways. The in situ formation of H{sub 2}O{sub 2} and decomposition into HO{sup •} can be also achieved using electron transfer mechanism in zero-valent aluminum/O{sub 2} system. Although these Fenton systems (except aluminum) work efficiently even at neutral pH, the H{sub 2}O{sub 2} activation mechanism is very specific to the nature of the catalyst and critically depends on its composition. This review describes in detail the complex mechanisms and emphasizes on practical limitations influencing their environmental applications.

  20. Advanced methods of solid oxide fuel cell modeling

    CERN Document Server

    Milewski, Jaroslaw; Santarelli, Massimo; Leone, Pierluigi

    2011-01-01

    Fuel cells are widely regarded as the future of the power and transportation industries. Intensive research in this area now requires new methods of fuel cell operation modeling and cell design. Typical mathematical models are based on the physical process description of fuel cells and require a detailed knowledge of the microscopic properties that govern both chemical and electrochemical reactions. ""Advanced Methods of Solid Oxide Fuel Cell Modeling"" proposes the alternative methodology of generalized artificial neural networks (ANN) solid oxide fuel cell (SOFC) modeling. ""Advanced Methods

  1. Experimental study on the advanced treatment of bio-chemically treated coking wastewater by the advanced Fenton oxidation process%Fenton高级氧化法深度处理焦化生化废水的实验研究

    Institute of Scientific and Technical Information of China (English)

    杨水莲; 田晓媛; 吴滨; 王威燕; 杨运泉

    2014-01-01

    The Fenton reagent used was made from ferrous sulphate and hydrogen peroxide. It is used in the advanced treatment of coking wastewater which was bio-chemically treated. The effects of the initial pH ,and dosages of FeSO4·7H2O,H2O2 and PAM on the treatment effectiveness of the bio-chemically treated coking wastewater have been investigated. The results show that using the advanced Fenton oxidation process can effectively remove the COD,NH3-N and chroma from this kind of coking wastewater. For bio-chemically treated coking wastewater with moderate concentration,the optimum conditions for Fenton oxidation process are as follows:the initial pH of waste-water is 8-10,dosage of FeSO4·7H2O 500 mg/L,dosage of H2O2 3.5 mL/L,and dosage of PAM 4.0 mg/L. Under these conditions,the removing rates of COD,NH3-N and Chroma can reach 85.9%,97.3%and 84.6%,respectively.%采用硫酸亚铁和过氧化氢所构成的Fenton试剂,对经生化处理后的焦化废水进行Fenton高级氧化深度处理,重点考察了废水初始pH,FeSO4·7H2O、H2O2及PAM投加量对焦化生化废水处理效果的影响。结果表明,采用Fenton高级氧化法可使经生化处理后的焦化废水中的COD、NH3-N和色度得到进一步有效去除。对于中等浓度的焦化生化废水,较适宜的Fenton氧化工艺条件:废水初始pH为8~10,FeSO4·7H2O投加量为500 mg/L,H2O2投加量为3.5 mL/L,PAM投加量为4.0 mg/L。在此条件下, COD、NH3-N和色度的去除率分别可达85.9%、97.3%和84.6%。

  2. 高级氧化技术在废水处理中的应用研究进展%Application and Progress of Advanced Oxidation Processes inWastewater Treatment

    Institute of Scientific and Technical Information of China (English)

    钟理; 詹怀宇

    2000-01-01

    探讨了高级氧化技术(Advanced Oxidation Processes,即AOPs)如:O3/H2O2,Fenton试剂均相湿式催化氧化;H2O2/UV、O3/UV、O3/H2O2/UV均相光催化氧化;多相湿式催化氧化,多相光催化氧化,多相催化和生化氧化等过程处理废水及其反应机理,论述了AOPs技术在工业废水处理方面的研究进展。%The wastewater treatment and reaction mechanism by Advanced Oxidation Processes such as homogeneous wet catalytic oxidation of O3/H2O2 and Fenton agent, homogeneous photocatalytic oxidation of H2O2/UV,O3/UV and O2/H2O2/UV, and heterogeneous wet catalytic oxidation, heterogeneous photocatalytic oxidation, heterogeneous catalytic and biochemical oxidation were explored. The investigation and progress of AOPs technique in industrial wastewater treatment were overviewed.

  3. Effluent polishing by means of advanced oxidation

    International Nuclear Information System (INIS)

    Three different Advanced Oxidation Processes (ozonation at pH 7.5, electron beam irradiation and a combination ozonation/electron beam irradiation) have been applied to study decomposition of aqueous naphthalene-1,5-disulfonic acid (1,5-NDSA) with regard to mineralization and formation of biodegradable intermediates. Formation of biodegradable intermediates could not be indicated for any of the processes used, single electron beam irradiation treatment was the most efficient process for mineralization of organic carbon contained in aqueous 1,5-NDSA. Applied to a real wastewater effluent from a mixed municipal/industrial wastewater electron beam irradiation with a radiation dose of 2 kGy was sufficient to reduce the concentrations of all naphthalene sulfonic acids and some of the alkylphenol ethoxylates by about 2 orders of magnitude. Moreover, high energy electrons effectively inactivate indicator bacteria in effluents from municipal wastewater treatment plants and eliminate simultaneously any estrogenic activity originating from natural and synthetic hormones also contained in the wastewater effluents. Inactivation of bacteria and bacterial spores by electron beam irradiation was found to be practically unaffected by the water matrix and suspended solids. There is a strong indication from literature data that these findings are also relevant to viruses of concern in water hygiene like poliovirus. Cost analysis of the irradiation process based on actual numbers from the first full scale wastewater treatment plant in the Republic of Korea indicated a total cost of about 0.2 US$/m3 treated water for 2 kGy irradiation dose. (author)

  4. Plasma Processing of Advanced Materials

    Energy Technology Data Exchange (ETDEWEB)

    Heberlein, Joachim, V.R.; Pfender, Emil; Kortshagen, Uwe

    2005-02-28

    Plasma Processing of Advanced Materials The project had the overall objective of improving our understanding of the influences of process parameters on the properties of advanced superhard materials. The focus was on high rate deposition processes using thermal plasmas and atmospheric pressure glow discharges, and the emphasis on superhard materials was chosen because of the potential impact of such materials on industrial energy use and on the environment. In addition, the development of suitable diagnostic techniques was pursued. The project was divided into four tasks: (1) Deposition of superhard boron containing films using a supersonic plasma jet reactor (SPJR), and the characterization of the deposition process. (2) Deposition of superhard nanocomposite films in the silicon-nitrogen-carbon system using the triple torch plasma reactor (TTPR), and the characterization of the deposition process. (3) Deposition of films consisting of carbon nanotubes using an atmospheric pressure glow discharge reactor. (4) Adapting the Thomson scattering method for characterization of atmospheric pressure non-uniform plasmas with steep spatial gradients and temporal fluctuations. This report summarizes the results.

  5. COD Removal of Different Industrial Wastewater by Fenton Oxidation Process

    OpenAIRE

    Yogita Sindhi*1

    2014-01-01

    Advanced oxidation processes are possibly one of the most effective methods for the treatment of wastewater containing organic products (effluents from chemical and agrochemical industries, the textile industry, paints, dyes, etc.).Fenton process is a one of advanced oxidation process. Fenton’s process have been extensively used for the removal of COD, TOC, dyes, phenolic compounds other organic chemicals from industrial and municipal wastewater. In this study, the laboratory s...

  6. DEGRADATION OF CAFFEINE AND METHYLENE BLUE BY ADVANCED OXIDATION PROCESSES (AOPs) = DEGRADAÇÃO DE CAFEÍNA E AZUL DE METILENO POR PROCESSOS OXIDATIVOS AVANÇADOS (POA)

    OpenAIRE

    Enelton Fagnani; Regiane Aparecida Guadagnini; Glenda Araújo Silva; José Roberto Guimarães

    2013-01-01

    The degradation of two compounds of pharmaceutical interest, caffeine (CAF) and methylene blue (MB), was studied using physical process (photolysis-UV254nm), chemical process (peroxidation-H2O2) and advanced oxidation processes: photoperoxidation (UV/H2O2), Fenton's reagent (Fe(II)/H2O2), photo-Fenton (Fe(II)/H2O2/UV) and heterogeneous photocatalysis (UV/TiO2). The aqueous samples were recirculated in the photoreactor and the processes were monitored using scanning spectrophotometry in the UV...

  7. Advances in machining process modeling

    International Nuclear Information System (INIS)

    Ever increasing speed and affordability of computing resources together with the advances in the modeling techniques made it possible to use the numerical models like finite element method (FEM), to simulate the metal cutting processes numerically. This paper explains the recent technological advances made in the commercial DEFORMTM system to facilitate the modeling of metal cutting process. During the first phase of this work a 2D system has been developed which assumes orthogonal cutting conditions. The second phase of this work has resulted in the development of a modeling system for 3D machining processes with main focus on turning. The modeling tools developed in this project utilize a hybrid procedure including both transient and steady state approaches. Automated remeshing procedure is being used with great success. Multiple coating layers on the insert can be modeled to study their thermal effects. Elastic and thermal response of the insert during the machining process can also be modeled using this system. The Usui's wear model has also been implemented in the system to study the tool wear. The system developed has been validated with various results reported from actual cutting tests and comparisons are found to be reasonably accurate

  8. Processos avançados de oxidação de compostos fenólicos em efluentes industriais Advanced Oxidation Process of phenolic compounds in industrial wasterwater

    OpenAIRE

    Jaildes Marques Britto; Maria do Carmo Rangel

    2008-01-01

    In an effort to minimize the impact on the environment, removal of pollutants, such as phenolic compounds, from the industrial wastewater has great importance nowadays because of the high toxicity and low biodegradability of these compounds. This work discusses the different methods to remove these compounds from industrial wastewater, showing their advantages and disadvantages. Advanced Oxidation Process (AOPs) are presented as a promising technology for the treatment of wastewater containin...

  9. Advanced diffusion processes and phenomena

    CERN Document Server

    Öchsner, Andreas; Belova, Irina

    2014-01-01

    This topical volume on Advanced Diffusion Processes and Phenomena addresses diffusion in a wider sense of not only mass diffusion but also heat diffusion in fluids and solids. Both diffusion phenomena play an important role in the characterization of engineering materials and corresponding structures. Understanding these different transport phenomena at many levels, from atomistic to macro, has therefore long attracted the attention of many researchers in materials science and engineering and related disciplines. The present topical volume captures a representative cross-section of some of the

  10. Development of Operational Parameters for Advanced Voloxidation Process at KAERI

    International Nuclear Information System (INIS)

    KAERI has been developing a voloxidation process as a head-end process of pyroprocessing technology with INL (Idaho National Laboratory). The work scope of KAERI is to develop the operation parameters for advanced voloxidation process at KAERI using surrogate materials and SIMFUEL. In order to evaluate operation conditions of an advanced voloxidation process, oxidation and vaporization behavior of metals and Cs compounds was investigated in terms of thermal treatment atmosphere and temperature by using thermodynamic data. And also, the oxidation and vaporization behavior of semi-volatile fission products with process pressure and temperature was investigated using surrogate materials. Particle size control for U3O8 powder was investigated using SIMFUEL and a rotary voloxidizer. According to analysis of KAERI works, the operation conditions for advanced voloxiation process may be consisted of the following four steps: 1) oxidation of UO2 pellet into U3O8 powder at 500 .deg. C in oxidative atmosphere, 2) additional oxidation of noble metal alloy and vaporization of high vapor pressure of fission products at 700 .deg. C in oxidative atmosphere, 3) granulation of U3O8 powder and vaporization of Cs compounds at 1200 .deg. C in an atmosphere of argon, and 4) reduction of UO2+x granules into UO2 granules at 1000 .deg. C in an atmosphere of 4%H2-Ar. This report will be used as a useful means for determining the operation parameters for advanced voloxidation process

  11. Recuperação de sílica-gel utilizando processos oxidativos avançados: uma alternativa simples e de baixo custo Silica gel recycling using and advanced oxidative process: a simple and low-cost alternative

    Directory of Open Access Journals (Sweden)

    Silvio César Godinho Teixeira

    2003-12-01

    Full Text Available Silica gel is widely used as adsorbent for isolating and purifying natural compounds. Intensive use and high cost make this process expensive and generate solid residues contaminated with many different organic compounds. In the present work a simple method for recycling silica was investigated, by using Advanced Oxidative Processes. Silica gel was treated with H2O2/solar light and compared with a sample treated by conventional methods (high temperature and oxidation with KMnO4. High temperature treatment changes the structure of the silica and, consequently, the separation efficiency. Oxidation by using KMnO4 requires multiple steps and produces residues, including manganese and oxalic acid. The method using H2O2/solar light to recuperate silica gel does not modify its separation efficiency and is less expensive than the traditional methods. Additionally, HPLC and GC-MS analysis indicate that H2O2/solar light eliminates all residues of the silica gel.

  12. 油脂加工过程中氧化稳定性的研究进展%Advance in oxidative stability of oil during processing

    Institute of Scientific and Technical Information of China (English)

    郑翠翠; 刘军; 邹宇晓; 施英; 廖森泰

    2014-01-01

    As an important energy storage material of human body, oil is rich in nutrition,and it is indis-pensable in modern life. However, oil is very easy to be oxidized and to generate hazardous substances, resulting in sharp reduction of nutritional value. The effects of processing technologies on oxidative stabil-ity index ( OSI) of oil were introduced based on the common oil processing technologies ( including ex-traction, refining and post processing of refined oil) , and the improvement direction aimed at the problem existed in the process of oil oxidation was put forward for future.%油脂是人体重要的储能物质,营养价值丰富,在日常生活中不可或缺,但其极易氧化酸败,生成有毒有害物质,造成其营养价值大幅降低。以常见油脂的加工工艺(包括提取、精炼和成品油后加工)为主线,着重介绍各加工工艺对油脂氧化稳定性的影响,并针对油脂氧化过程中存在的问题提出今后可改进的方向。

  13. Investigation on Advanced Oxidation-Biological Processes in Pharmaceutical Wastewater Treatment%高级氧化与生物联用技术处理制药废水的研究

    Institute of Scientific and Technical Information of China (English)

    申晓辉; 申婷婷; 李小明; 岳秀; 柳娴; 唐玉芳

    2011-01-01

    制药工业废水成分复杂,有机污染物种类多,难于降解,毒性大。高级氧化技术处理制药废水尚处于实验研究阶段,然而将其与生物法联合具有良好的应用前景。重点介绍了各类高级氧化技术的原理和特点,讨论了高级氧化及生物联用技术运用于制药废水的处理现状、存在的问题及未来发展方向。%Pharmaceutical industrial wastewater contained high concentration of organic matters and was characterized by extremely poor biodegradability and toxicity.Although advanced oxidation processes(AOPs) used in the pharmaceutical wastewater treatment was generally at the batch experiment stage,yet it had bright application prospect in combining with biological treatment.The elaboration of the principle and characteristics of various advanced oxidation processes as well as the present situation were focused on,and the existing problems and future development direction of advanced oxidation-biological processes in pharmaceutical wastewater treatment were discussed.

  14. Emerging materials by advanced processing

    International Nuclear Information System (INIS)

    This volume contains 36 contributions with following subjects (selection): Densification of highly reactive aluminium titanate powders; influence of precursor history on carbon fiber characteristics; influence of water removal rate during calcination on the crystallization of ZrO2 from amorphous hydrous precipitates; tape casting of AlN; influence of processing on the properties of beta-SiC powders; corrosion of SiSiC by gases and basic slag at high temperature; influence of sintering and thermomechanical treatment on microstructure and properties of W-Ni-Fe alloys; mechanical alloying for development of sintered steels with high hard phase content (NbC); early stages of mechanical alloying in Ni-Ti and Ni-Al powder mixtures; growth and microstructural development of melt-oxidation derived Al2O3/Al-base composites; fabrication of RSBN composites; synthesis of high density coridierite bodies; comparative studies on post-HIP and sinter-HIP treatments on transformation thoughened ceramics; sinter HIP of SiC; precipitation mixing of Si3N4 with bimetallic oxides; temperature dependence of the interfacial energies in Al2O3-liquid metal systems; synthesis and microstructural examination of Synroc B; solid state investigation of ceramic-metal bonding; thermophysical properties of MgAl2O4; preparation, sintering and thermal expansion of MgAl2O4; microstructural studies on alumina-zirconia and metallized alumina ceramics; electrodeposition of metals (e.g. Ti, Mo, In) and metal oxides from molten salts; electrochemical deposition of Ti from nonaqueous media (DMSO, DMF); lithium as anode material in power sources (passivation); reduction of chromium(VI) when solar selective black chromium is deposited; thermodynamic optimization of phase diagrams (computer calculations); optimization of Na-Tl phase diagram; phase relations in the Y-Si-Al-O-N system: Controlled manufacturing of alpha/beta-SIALON composites. (MM)

  15. Impact of leachate composition on the advanced oxidation treatment.

    Science.gov (United States)

    Oulego, Paula; Collado, Sergio; Laca, Adriana; Díaz, Mario

    2016-01-01

    Advanced oxidation processes (AOPs) are gaining importance as an alternative to the biological or physicochemical treatments for the management of leachates. In this work, it has been studied the effect of the characteristics of the leachate (content in humic acids, landfill age and degree of stabilization) on the wet oxidation process and final quality of the treated effluent. A high concentration of humic acids in the leachate had a positive effect on the COD removal because this fraction is more easily oxidizable. Additionally, it has been demonstrated that the simultaneous presence of humic acid and the intermediates generated during the oxidation process improved the degradation of this acid, since such intermediates are stronger initiators of free radicals than the humic acid itself. Similar values of COD removals (49% and 51%) and biodegradability indices (0.30 and 0.35) were observed, after 8 h of wet oxidation, for the stabilised leachate (biologically pretreated) and the raw one, respectively. Nevertheless, final colour removal was much higher for the stabilised leachate, achieving values up to 91%, whereas for the raw one only 56% removal was attained for the same reaction time. Besides, wet oxidation treatment was more efficient for the young leachate than for the old one, with final COD conversions of 60% and 37%, respectively. Eventually, a triangular "three-lump" kinetic model, which considered direct oxidation to CO2 and partial oxidation through intermediate compounds, was here proposed. PMID:26517790

  16. Electrochromic Windows: Advanced Processing Technology

    Energy Technology Data Exchange (ETDEWEB)

    SAGE Electrochromics, Inc

    2006-12-13

    This project addresses the development of advanced fabrication capabilities for energy saving electrochromic (EC) windows. SAGE EC windows consist of an inorganic stack of thin films deposited onto a glass substrate. The window tint can be reversibly changed by the application of a low power dc voltage. This property can be used to modulate the amount of light and heat entering buildings (or vehicles) through the glazings. By judicious management of this so-called solar heat gain, it is possible to derive significant energy savings due to reductions in heating lighting, and air conditioning (HVAC). Several areas of SAGE’s production were targeted during this project to allow significant improvements to processing throughput, yield and overall quality of the processing, in an effort to reduce the cost and thereby improve the market penetration. First, the overall thin film process was optimized to allow a more robust set of operating points to be used, thereby maximizing the yield due to the thin film deposition themselves. Other significant efforts aimed at improving yield were relating to implementing new procedures and processes for the manufacturing process, to improve the quality of the substrate preparation, and the quality of the IGU fabrication. Furthermore, methods for reworking defective devices were developed, to enable devices which would otherwise be scrapped to be made into useful product. This involved the in-house development of some customized equipment. Finally, the improvements made during this project were validated to ensure that they did not impact the exceptional durability of the SageGlass® products. Given conservative estimates for cost and market penetration, energy savings due to EC windows in residences in the US are calculated to be of the order 0.026 quad (0.026×1015BTU/yr) by the year 2017.

  17. Advanced oxidation of the commercial nonionic surfactant octylphenol polyethoxylate Triton™ X-45 by the persulfate/UV-C process: effect of operating parameters and kinetic evaluation

    Science.gov (United States)

    Arslan-Alaton, Idil; Olmez-Hanci, Tugba; Genç, Bora; Dursun, Duygu

    2013-01-01

    This study explored the potential use of a sulfate radical (SO·−4)-based photochemical oxidation process to treat the commercial nonionic surfactant octylphenol polyethoxylate (OPPE) Triton™ X-45. For this purpose, the effect of initial S2O2−8 (0–5.0 mM) and OPPE (10–100 mg/L) concentrations on OPPE and its organic carbon content (TOC) removal were investigated at an initial reaction pH of 6.5. Results indicated that very fast OPPE degradation (100%) accompanied with high TOC abatement rates (90%) could be achieved for 10 and 20 mg/L aqueous OPPE at elevated S2O2−8 concentrations (≥2.5 mM). S2O2−8/UV-C treatment was still capable of complete OPPE removal up to an initial concentration of 40 mg/L in the presence of 2.5 mM S2O2−8. On the other hand, TOC removal efficiencies dropped down to only 40% under the same reaction conditions. S2O2−8/UV-C oxidation of OPPE was also compared with the relatively well-known and established H2O2/UV-C oxidation process. Treatment results showed that the performance of S2O2−8/UV-C was comparable to that of H2O2/UV-C oxidation for the degradation and mineralization of OPPE. In order to elucidate the relative reactivity and selectivity of SO·−4 and HO·, bimolecular reaction rate coefficients of OPPE with SO·−4 and HO· were determined by employing competition kinetics with aqueous phenol (47 μM) selected as the reference compound. The pseudo-first-order abatement rate coefficient obtained for OPPE during S2O2−8/UV-C oxidation (0.044 min−1) was found to be significantly lower than that calculated for phenol (0.397 min−1). In the case of H2O2/UV-C oxidation however, similar pseudo-first-order abatement rate coefficients were obtained for both OPPE (0.087 min−1) and phenol (0.140 min−1). From the kinetic study, second-order reaction rate coefficients for OPPE with SO·−4 and HO· were determined as 9.8 × 108 M−1 s−1 and 4.1 × 109 M−1 s−1, respectively. The kinetic study also revealed

  18. Advanced oxidation of the commercial nonionic surfactant octylphenol polyethoxylate Triton™ X-45 by the persulfate/UV-C process: effect of operating parameters and kinetic evaluation

    OpenAIRE

    IdilArslan-Alaton

    2013-01-01

    This study explored the potential use of a sulfate radical (SO·− 4)-based photochemical oxidation process to treat the commercial nonionic surfactant octylphenol polyethoxylate (OPPE) Triton™ X-45. For this purpose, the effect of initial S2O2− 8 (0–5.0 mM) and OPPE (10–100 mg/L) concentrations on OPPE and its organic carbon content (TOC) removal were investigated at an initial reaction pH of 6.5. Results indicated that very fast OPPE degradation (100%) accompanied with high TOC abatement rate...

  19. Development of Advanced Voloxidation Process for Treatment of Spent Fuel

    International Nuclear Information System (INIS)

    Data for evaluation of the effects of advanced voloxidation on pyroprocessing of spent oxide fuel with a determination for a path forward such was produced as follows: effect of particle size and particle structure on oxide reduction, assessment of decladding options for pyroprocessing, effect of removal timing of fission products, analysis of radioactivity and decay heat of advanced voloxidation process, proliferation resistance of advanced voloxidation process, Effect of advanced voloxidation process on shielding. Also, performance objectives for advanced voloxidation with respective to the down stream effects was established. The technology on design and manufacture of voloxidation and off gas treatment equipment was established. The possibility of fabrication of porous granule as a feed material for electro-reduction process was confirmed using rotary voloxidizer and SIMFUEL. The operational conditions for advanced voloxidation process consisting of 4 steps heat treatment was drawn to vaporize fission products and fabricate UO2 granule. The trapping test of Cs and Re(surrogate material of Tc) using newly developed filter were selectively separated at trapping efficiency of 99%, respectively. Data for oxidative decladding, vaporization rate of fission products, and particle size from experiment on voloxidation using spent fuel in ILN hot cell was acquisited including data of off gas trapping characteristics and verification of excellent performance of filter

  20. Advances in uranium enrichment processes

    International Nuclear Information System (INIS)

    Advances in gas centrifuges and development of the atomic vapour laser isotope separation process promise substantial reductions in the cost of enriched uranium. The resulting reduction in LWR fuel costs could seriously erode the economic advantage of CANDU, and in combination with LWR design improvements, shortened construction times and increased operational reliability could allow the LWR to overtake CANDU. CANDU's traditional advantages of neutron economy and high reliability may no longer be sufficient - this is the challenge. The responses include: combining neutron economy and dollar economy by optimizing CANDU for slightly enriched uranium fuel; developing cost-reducing improvements in design, manufacture and construction; and reducing the cost of heavy water. Technology is a renewable resource which must be continually applied to a product for it to remain competitive in the decades to come. Such innovation is a prerequisite to Canada increasing her share of the international market for nuclear power stations. The higher burn-up achievable with enriched fuel in CANDU can reduce the fuel cycle costs by 20 to 40 percent for a likely range of costs for yellowcake and separative work. Alternatively, some of the benefits of a higher fissile content can take the form of a cheaper reactor core containing fewer fuel channels and less heavy water, and needing only a single fuelling machine. An opportunity that is linked to this need to introduce an enriched uranium fuel cycle into CANDU is to build an enrichment business in Canada. This could offer greater value added to our uranium exports, security of supply for enriched CANDUs, technological growth in Canada and new employment opportunities. AECL has a study in progress to define this opportunity

  1. Advanced Materials and Processing 2010

    Science.gov (United States)

    Zhang, Yunfeng; Su, Chun Wei; Xia, Hui; Xiao, Pengfei

    2011-06-01

    Strain sensors made from MWNT/polymer nanocomposites / Gang Yin, Ning Hu and Yuan Li -- Shear band evolution and nanostructure formation in titanium by cold rolling / Dengke Yang, Peter D. Hodgson and Cuie Wen -- Biodegradable Mg-Zr-Ca alloys for bone implant materials / Yuncang Li ... [et al.] -- Hydroxyapatite synthesized from nanosized calcium carbonate via hydrothermal method / Yu-Shiang Wu, Wen-Ku Chang and Min Jou -- Modeling of the magnetization process and orthogonal fluxgate sensitivity of ferromagnetic micro-wire arrays / Fan Jie ... [et al.] -- Fabrication of silicon oxide nanowires on Ni coated silicon substrate by simple heating process / Bo Peng and Kwon-Koo Cho -- Deposition of TiOxNy thin films with various nitrogen flow rate: growth behavior and structural properties / S.-J. Cho ... [et al.] -- Observation on photoluminescence evolution in 300 KeV self-ion implanted and annealed silicon / Yu Yang ... [et al.] -- Facile synthesis of lithium niobate from a novel precursor H[symbol] / Meinan Liu ... [et al.] -- Effects of the buffer layers on the adhesion and antimicrobial properties of the amorphous ZrAlNiCuSi films / Pai-Tsung Chiang ... [et al.] -- Fabrication of ZnO nanorods by electrochemical deposition process and its photovoltaic properties / Jin-Hwa Kim ... [et al.] -- Cryogenic resistivities of NbTiAlVTaLax, CoCrFeNiCu and CoCrFeNiAl high entropy alloys / Xiao Yang and Yong Zhang -- Modeling of centrifugal force field and the effect on filling and solidification in centrifugal casting / Wenbin Sheng, Chunxue Ma and Wanli Gu -- Electrochemical properties of TiO[symbol] nanotube arrays film prepared by anodic oxidation / Young-Jin Choi ... [et al.] -- Effect of Ce additions on high temperature properties of Mg-5Sn-3Al-1Zn alloy / Byoung Soo Kang ... [et al.] -- Sono-electroless plating of Ni-Mo-P film / Atsushi Chiba, Masato Kanou and Wen-Chang Wu -- Diameter dependence of giant magneto-impedance effect in co-based melt extracted amorphous

  2. Advances in Mechanisms of Anti-oxidation

    OpenAIRE

    Ma, Qiang

    2014-01-01

    Reactive oxygen species (ROS) are a family of molecules that are continuously produced from oxygen consumption in aerobic cells. Controlled generation of ROS in normal cells serves useful purposes to regulate important cellular processes such as cell proliferation, inflammation, and immune response, but overproduction of ROS causes oxidative stress that contributes to the development of cancer, chronic disease, and aging. These hugely different consequences of ROS exposure demand a carefully ...

  3. Decontamination of used pesticide packaging using advanced oxidation process by ionizing radiation; Descontaminacao de embalagens descartadas de clorpirifos utilizando o processo de oxidacao avancada por radiacao ionizante

    Energy Technology Data Exchange (ETDEWEB)

    Mori, Manoel Nunes

    2006-07-01

    The discharge of empty plastic packaging of pesticides can be an environmental concern causing problems to human health, animals and plants if done without inspection and monitoring. Among the commercial pesticides, chloropyrifos has significant importance because of its wide distribution and extensive use and persistence. The hydroxyl OH attack is the most efficient process of chemical oxidation. The radiation-induced degradation of chloropyrifos in liquid samples and in polyethylene pack was studied by gamma-radiolysis. Packaging of high density polyethylene tree layer co extruded, named COEX, and water samples contaminated with chloropyrifos, were irradiated using both, a multipurpose Co-60 gamma irradiator and a gamma source with 5,000 Ci total activity, Gamma cell type. The chemical analysis of the chloropyrifos and by-products were made using a gas chromatography associated to the mass spectrometry. Gamma radiation was efficient for removing chloropyrifos from the plastic packaging in all studied cases. (author)

  4. Formation of High-quality Advanced High-k Oxide Layers at Low Temperature by Excimer UV Lamp-assisted Photo-CVD and Sol-gel Processing

    Institute of Scientific and Technical Information of China (English)

    YU J. J.

    2004-01-01

    We have successfully demonstrated that high quality and high dielectric constant layers can be fabricated by low temperature photo-induced or -assisted processing. Ta2O5 and ZrO2 have been deposited at t<400 ℃by means of a UV photo-CVD technique and HfO2 by photo-assisted sol-gel processing with the aid of excimer lamps. The UV annealing of as-grown layers was found to significantly improve their electrical properties.Low leakage current densities on the order of 10-8 A/cm2 at 1 MV/cm for deposited ultrathin Ta2O5 films and ca. 10-6 A/cm2 for the photo-CVD ZrO2 layers and photo-irradiated sol-gel HfO2 layers have been readily achieved. The improvement in the leakage properties of these layers is attributed to the UV-generated active oxygen species O(1D) which strongly oxidize any suboxides to form more stoichiometric oxides on removing certain defects, oxygen vacancies and impurities present in the as-prepared layers. The photo-CVD Ta2O5films deposited across 10. 16-cm Si wafers exhibit a high thickness uniformity with a variation of less than ±2.0% being obtained for ultrathin ca. 10 nm thick films. The lamp technology can in principle be extended to larger area wafers, providing a promising low temperature route to the fabrication of a range of high quality thin films for future ULSI technology.

  5. Degradation and mineralization of Bisphenol A (BPA) in aqueous solution using advanced oxidation processes: UV/H2O2 and UV/S2O8(2-) oxidation systems.

    Science.gov (United States)

    Sharma, Jyoti; Mishra, I M; Kumar, Vineet

    2015-06-01

    This work reports on the removal and mineralization of an endocrine disrupting chemical, Bisphenol A (BPA) at a concentration of 0.22 mM in aqueous solution using inorganic oxidants (hydrogen peroxide, H2O2 and sodium persulfate, Na2S2O8;S2O8(2-)) under UV irradiation at a wavelength of 254 nm and 40 W power (Io = 1.26 × 10(-6) E s(-1)) at its natural pH and a temperature of 29 ± 3 °C. With an optimum persulfate concentration of 1.26 mM, the UV/S2O8(2-) process resulted in ∼95% BPA removal after 240 min of irradiation. The optimum BPA removal was found to be ∼85% with a H2O2 concentration of 11.76 mM. At higher concentrations, either of the oxidants showed an adverse effect because of the quenching of the hydroxyl or sulfate radicals in the BPA solution. The sulfate-based oxidation process could be used over a wider initial pH range of 3-12, but the hydroxyl radical-based oxidation of BPA should be carried out in the acidic pH range only. The water matrix components (bicarbonate, chloride and humic acid) showed higher scavenging effect in hydroxyl radical-based oxidation than that in the sulfate radical-based oxidation of BPA. UV/S2O8(2-) oxidation system utilized less energy (307 kWh/m(3)) EE/O in comparison to UV/H2O2 system (509 kWh/m(3)) under optimum operating conditions. The cost of UV irradiation far outweighed the cost of the oxidants in the process. However, the total cost of treatment of persulfate-based system was much lower than that of H2O2-based oxidation system. PMID:25889275

  6. COD removal from pulp and paper effluents by Advanced Oxidation Processes (AOP); COD:n vaehentaeminen aop-menetelmaellae metsaeteollisuuden jaetevesistae - EKY 04

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, K.; Wikberg, H. [Kemira Chemicals Oy, Vaasa (Finland)

    1998-12-31

    The aim of this project is to develop a process where COD from pulp and paper industry can be removed by an AOP process. AOP is a process utilizing the oxidation power of the hydroxyl radical, which can be produced in many different ways. Compared to evaporation and membrane techniques, the benefits of this process are lack of condense, concentrate and sludge. It is a very simple process, based on adjusting the COD removal by means of hydrogen peroxide dosage. The study focuses on using heterogeneous catalyst together with hydrogen peroxide to produce hydroxyl radicals in order to remove COD at low temperatures (< 100 deg C) and normal pressures. The project started by screening catalysts able to perform this task in laboratory scale. Later on pilot scale equipment will be constructed for use in pulp and paper mill trials. The project will be carried out during 1997-1999. The study started by screening the possibilities of different catalysts together with hydrogen peroxide to remove phenols from a model water. Sofar, about hundred catalysts have been screened. These tests show that many of the heterogeneous catalysts are working, but most of them have actually dissolved in the water and `translated` to homogenous catalysts. This means that they cannot be used in this project. A few catalysts have been found to meet the targets for synthetic phenol waters. Next step will be to test these catalysts on actual water samples from pulp and paper mills, and after that a pilot and full-scale trial will be planned. In these trials we will find out which mill streams are possible to treat, and the cost/performances of a system totally based on the catalyst in use. Also, measurements of catalyst leaching and clogging will be made during these tests. The last test series is planned to be a full-scale trial. (orig.)

  7. Advanced thermally assisted surface engineering processes

    CERN Document Server

    Chattopadhyay, Ramnarayan

    2007-01-01

    Preface. Acknowledgements. 1: Wear, Surface Heat and Surface Engineering. 2: Plasma Assisted Thermal Processes. 3: Ion Beam Processes. 4: Electron Beam Processes. 5: Microwave Assisted Surface Modification Processes. 6: Laser Assisted Surface Engineering Processes. 7: Solar Energy for Surface Modifications. 8: Combustion Processes for Surface Modification. 9: Friction Weld Surfacing. 10: Induction Surface Modification Processes. 11: Surfacing by Spark Deposition Processes. 12: Arc Assisted Advanced Surface Engineering Processes. 13: Hot Isostatic Press. 14: Fluid Bed Processes. 15: P

  8. ADVANCED OXIDATION: OXALATE DECOMPOSITION TESTING WITH OZONE

    Energy Technology Data Exchange (ETDEWEB)

    Ketusky, E.; Subramanian, K.

    2012-02-29

    At the Savannah River Site (SRS), oxalic acid is currently considered the preferred agent for chemically cleaning the large underground Liquid Radioactive Waste Tanks. It is applied only in the final stages of emptying a tank when generally less than 5,000 kg of waste solids remain, and slurrying based removal methods are no-longer effective. The use of oxalic acid is preferred because of its combined dissolution and chelating properties, as well as the fact that corrosion to the carbon steel tank walls can be controlled. Although oxalic acid is the preferred agent, there are significant potential downstream impacts. Impacts include: (1) Degraded evaporator operation; (2) Resultant oxalate precipitates taking away critically needed operating volume; and (3) Eventual creation of significant volumes of additional feed to salt processing. As an alternative to dealing with the downstream impacts, oxalate decomposition using variations of ozone based Advanced Oxidation Process (AOP) were investigated. In general AOPs use ozone or peroxide and a catalyst to create hydroxyl radicals. Hydroxyl radicals have among the highest oxidation potentials, and are commonly used to decompose organics. Although oxalate is considered among the most difficult organic to decompose, the ability of hydroxyl radicals to decompose oxalate is considered to be well demonstrated. In addition, as AOPs are considered to be 'green' their use enables any net chemical additions to the waste to be minimized. In order to test the ability to decompose the oxalate and determine the decomposition rates, a test rig was designed, where 10 vol% ozone would be educted into a spent oxalic acid decomposition loop, with the loop maintained at 70 C and recirculated at 40L/min. Each of the spent oxalic acid streams would be created from three oxalic acid strikes of an F-area simulant (i.e., Purex = high Fe/Al concentration) and H-area simulant (i.e., H area modified Purex = high Al/Fe concentration

  9. Practical advanced oxidation processes for waste water treatment:I. the principle, characteristic, advantage and disadvantage of various advanced oxidation technologies%废水处理的实用高级氧化技术第一部分──各类高级氧化技术的原理、特性和优缺点

    Institute of Scientific and Technical Information of China (English)

    方景礼

    2014-01-01

    评述了芬顿氧化法、催化臭氧氧化法、光催化氧化法、电解催化氧化法、湿式空气氧化/湿式催化氧化法、超临界水氧化法、超声氧化法等各类目前认为最有实用价值的高级氧化技术的原理、特性和各自的优缺点,分析了各类高级氧化技术存在的问题和未来的发展趋势。认为金属催化臭氧氧化技术结合了臭氧氧化力强和金属催化剂易于制造、经久耐用、不需另加其他药剂和操作成本低的优点,是既经济又高效的氧化技术,也是未来较有发展前途的技术。%The principles, characteristics, advantages, and disadvantages of the various most practical advanced oxidation technologies recently, for example, Fenton oxidation, catalytic ozone oxidation, photocatalytic oxidation, electrolytic catalytic oxidation, wet air oxidation and catalytic wet air oxidation, supercritical water oxidation, and supersonic oxidation, were reviewed and the problems existing in various advanced oxidation technologies and the development tendency in the further were analyzed. It is considered that the metal-catalyzed ozone oxidation is an economic and highly efficient oxidation technology combining the advantages of both ozone’s strong oxidation ability and metal catalyzer’ easy manufacturing, high durability, no need of adding other reagents, and low operation cost, showing a good development prospect in the future.

  10. 废水处理的实用高级氧化技术第一部分──各类高级氧化技术的原理、特性和优缺点%Practical advanced oxidation processes for waste water treatment:I. the principle, characteristic, advantage and disadvantage of various advanced oxidation technologies

    Institute of Scientific and Technical Information of China (English)

    方景礼

    2014-01-01

    评述了芬顿氧化法、催化臭氧氧化法、光催化氧化法、电解催化氧化法、湿式空气氧化/湿式催化氧化法、超临界水氧化法、超声氧化法等各类目前认为最有实用价值的高级氧化技术的原理、特性和各自的优缺点,分析了各类高级氧化技术存在的问题和未来的发展趋势。认为金属催化臭氧氧化技术结合了臭氧氧化力强和金属催化剂易于制造、经久耐用、不需另加其他药剂和操作成本低的优点,是既经济又高效的氧化技术,也是未来较有发展前途的技术。%The principles, characteristics, advantages, and disadvantages of the various most practical advanced oxidation technologies recently, for example, Fenton oxidation, catalytic ozone oxidation, photocatalytic oxidation, electrolytic catalytic oxidation, wet air oxidation and catalytic wet air oxidation, supercritical water oxidation, and supersonic oxidation, were reviewed and the problems existing in various advanced oxidation technologies and the development tendency in the further were analyzed. It is considered that the metal-catalyzed ozone oxidation is an economic and highly efficient oxidation technology combining the advantages of both ozone’s strong oxidation ability and metal catalyzer’ easy manufacturing, high durability, no need of adding other reagents, and low operation cost, showing a good development prospect in the future.

  11. Effect of advanced oxidation processes on the micropollutants and the effluent organic matter contained in municipal wastewater previously treated by three different secondary methods.

    Science.gov (United States)

    Giannakis, Stefanos; Gamarra Vives, Franco Alejandro; Grandjean, Dominique; Magnet, Anoys; De Alencastro, Luiz Felippe; Pulgarin, César

    2015-11-01

    In this study, wastewater from the output of three different secondary treatment facilities (Activated Sludge, Moving Bed Bioreactor and Coagulation-Flocculation) present in the municipal wastewater treatment plant of Vidy, Lausanne (Switzerland), was further treated with various oxidation processes (UV, UV/H2O2, solar irradiation, Fenton, solar photo-Fenton), at laboratory scale. For this assessment, 6 organic micropollutants in agreement with the new environmental legislation requirements in Switzerland were selected (Carbamazepine, Clarithromycin, Diclofenac, Metoprolol, Benzotriazole, Mecoprop) and monitored throughout the treatment. Also, the overall removal of the organic load was assessed. After each secondary treatment, the efficiency of the AOPs increased in the following order: Coagulation-Flocculation Bioreactor, in almost all cases. From the different combinations tested, municipal wastewater subjected to biological treatment followed by UV/H2O2 resulted in the highest elimination levels. Wastewater previously treated by physicochemical treatment demonstrated considerably inhibited micropollutant degradation rates. The degradation kinetics were determined, yielding: k (UV) photo-Fenton). Finally, the evolution of global pollution parameters (COD & TOC elimination) was followed and the degradation pathways for the effluent organic matter are discussed. PMID:26255127

  12. Hydrogen production with short contact time. Catalytic partial oxidation of hydrocarbons and oxygenated compounds: Recent advances in pilot- and bench-scale testing and process design

    Energy Technology Data Exchange (ETDEWEB)

    Guarinoni, A.; Ponzo, R.; Basini, L. [ENI Refining and Marketing Div., San Donato Milanese (Italy)

    2010-12-30

    ENI R and D has been active for fifteen years in the development of Short Contact Time - Catalytic Partial Oxidation (SCT-CPO) technologies for producing Hydrogen/Synthesis Gas. From the beginning the experimental work addressed either at defining the fundamental principles or the technical and economical potential of the technology. Good experimental responses, technical solutions' simplicity and flexibility, favourable techno-economical evaluations promoted the progressive widening of the field of the investigations. From Natural Gas (NG) the range of ''processable'' Hydrocarbons extended to Liquefied Petroleum Gas (LPG) and Gasoils, including those characterised by high levels of unsaturated and sulphurated molecules and, lately, to other compounds with biological origin. The extensive work led to the definition of different technological solutions, grouped as follows: Technology 1: Air Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 2: Enriched Air/Oxygen Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 3: Enriched Air/Oxygen Blown SCT-CPO of Liquid Hydrocarbons and/or Compounds with biological origin Recently, the licence rights on a non-exclusive basis for the commercialisation of SCT-CPO based processes for H{sub 2}/Synthesis gas production from light hydrocarbons with production capacity lower than 5,000 Nm{sup 3}/h of H{sub 2} or 7,500 Nm3/h of syngas have been assigned to two external companies. In parallel, development of medium- and large-scale plant solutions is progressing within the ENI group framework. These last activities are addressed to the utilisation of SCT-CPO for matching the variable Hydrogen demand in several contexts of oil refining operation. This paper will report on the current status of SCT-CPO with a focus on experimental results obtained, either at pilot- and bench- scale level. (orig.)

  13. Nontraditional machining processes research advances

    CERN Document Server

    2013-01-01

    Nontraditional machining employs processes that remove material by various methods involving thermal, electrical, chemical and mechanical energy or even combinations of these. Nontraditional Machining Processes covers recent research and development in techniques and processes which focus on achieving high accuracies and good surface finishes, parts machined without burrs or residual stresses especially with materials that cannot be machined by conventional methods. With applications to the automotive, aircraft and mould and die industries, Nontraditional Machining Processes explores different aspects and processes through dedicated chapters. The seven chapters explore recent research into a range of topics including laser assisted manufacturing, abrasive water jet milling and hybrid processes. Students and researchers will find the practical examples and new processes useful for both reference and for developing further processes. Industry professionals and materials engineers will also find Nontraditional M...

  14. Advanced methods for processing ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Carter, W.B. [Georgia Institute of Technology, Atlanta, GA (United States)

    1995-05-01

    Combustion chemical vapor deposition (CCVD) is a flame assisted, open air chemical vapor deposition (CVD) process. The process is capable of producing textured, epitaxial coatings on single crystal substrates using low cost reagents. Combustion chemical vapor deposition is a relatively inexpensive, alternative thin film deposition process with potential to replace conventional coating technologies for certain applications. The goals of this project are to develop the CCVD process to the point that potential industrial applications can be identified and reliably assessed.

  15. Oxidative Stress to the Cornea, Changes in Corneal Optical Properties, and Advances in Treatment of Corneal Oxidative Injuries

    Directory of Open Access Journals (Sweden)

    Cestmir Cejka

    2015-01-01

    Full Text Available Oxidative stress is involved in many ocular diseases and injuries. The imbalance between oxidants and antioxidants in favour of oxidants (oxidative stress leads to the damage and may be highly involved in ocular aging processes. The anterior eye segment and mainly the cornea are directly exposed to noxae of external environment, such as air pollution, radiation, cigarette smoke, vapors or gases from household cleaning products, chemical burns from splashes of industrial chemicals, and danger from potential oxidative damage evoked by them. Oxidative stress may initiate or develop ocular injury resulting in decreased visual acuity or even vision loss. The role of oxidative stress in the pathogenesis of ocular diseases with particular attention to oxidative stress in the cornea and changes in corneal optical properties are discussed. Advances in the treatment of corneal oxidative injuries or diseases are shown.

  16. Oxidative stress to the cornea, changes in corneal optical properties, and advances in treatment of corneal oxidative injuries.

    Science.gov (United States)

    Cejka, Cestmir; Cejkova, Jitka

    2015-01-01

    Oxidative stress is involved in many ocular diseases and injuries. The imbalance between oxidants and antioxidants in favour of oxidants (oxidative stress) leads to the damage and may be highly involved in ocular aging processes. The anterior eye segment and mainly the cornea are directly exposed to noxae of external environment, such as air pollution, radiation, cigarette smoke, vapors or gases from household cleaning products, chemical burns from splashes of industrial chemicals, and danger from potential oxidative damage evoked by them. Oxidative stress may initiate or develop ocular injury resulting in decreased visual acuity or even vision loss. The role of oxidative stress in the pathogenesis of ocular diseases with particular attention to oxidative stress in the cornea and changes in corneal optical properties are discussed. Advances in the treatment of corneal oxidative injuries or diseases are shown. PMID:25861412

  17. Solidification process control for advanced superalloys

    Science.gov (United States)

    Gray, H. R.; Dreshfield, R. L.

    1982-01-01

    The importance of understanding and controlling the basic solidification process in high temperature alloy technology as applied to gas turbine engine production is discussed. Resultant tailoring of the superalloy macro- and microstructure offers significant potential for continued advances in superalloy use temperatures in turbine engines. Atomized superalloy powders, rapidly solidified superalloys, microstructural control, and advanced superalloys are discussed.

  18. Study of oil diesel degradation in soil using oxidative advanced processes; Estudo da degradacao do oleo diesel em solo utilizando processos oxidativos avancados

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Suenia S.; Silva, Valdinete L. da; Motta, Mauricio da [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Engenharia Quimica; Silva, Paula Tereza de S. e; Barros Neto, Benicio de [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Quimica Fundamental

    2004-07-01

    Recently it comes if observing several accidents during the exploration, refinement, transport and operation of storage of petroleum and yours derived, such as the diesel oil and the gasoline. In this paper We do a study of the degradation of the diesel oil in a characteristic soil of the state of Pernambuco using peroxide of hydrogen and Fenton reagent. Those two processes are based on the generation of the radical hydroxyl (OH.) that has to can oxidizer loud capable to promote the destruction of recalcitrant organic compositions. The studied soil has about 16,5{+-}0,3 g/kg of total organic carbon. A factorial planning was accomplished 2{sup 3} with 2 repetitions in the central point with the objective of finding the best conditions of degradation of the pollutant. The variables and the studied levels were: FeSO{sub 4} - 0,18 M (0, 4 and 8 Ml); pH (3; without adjustment and without adjustment) and Time of exhibition in the sun (8; 12 and 16:00). The volumes of H{sub 2}O{sub 2} used in the rehearsals were constant, being 80 mL. Soon afterwards it accomplished a fractional experimental planning 2{sup 3-1}, repeating the variables of the first planning, they put using a smaller volume of H{sub 2}O{sub 2}, 40 mL, to evaluate the influence of the amount of H{sub 2}O{sub 2} used about the degradation of the diesel oil. The mass of the soil used in each experiment was of 5 g. It was observed that there were not significant differences in the degradation in relation to the peroxide volume. The best found degradation was around 87% in the following conditions (4 mL of Faith, without pH adjustment, Time of exhibition in the sun of 12:00 and 80 ml of H{sub 2}O{sub 2}). That found degradation was quite satisfactory being still due to study more economical conditions. (author)

  19. Advancements in Big Data Processing

    CERN Document Server

    Vaniachine, A; The ATLAS collaboration

    2012-01-01

    The ever-increasing volumes of scientific data present new challenges for Distributed Computing and Grid-technologies. The emerging Big Data revolution drives new discoveries in scientific fields including nanotechnology, astrophysics, high-energy physics, biology and medicine. New initiatives are transforming data-driven scientific fields by pushing Bid Data limits enabling massive data analysis in new ways. In petascale data processing scientists deal with datasets, not individual files. As a result, a task (comprised of many jobs) became a unit of petascale data processing on the Grid. Splitting of a large data processing task into jobs enabled fine-granularity checkpointing analogous to the splitting of a large file into smaller TCP/IP packets during data transfers. Transferring large data in small packets achieves reliability through automatic re-sending of the dropped TCP/IP packets. Similarly, transient job failures on the Grid can be recovered by automatic re-tries to achieve reliable Six Sigma produc...

  20. Advanced Electrorefining Process at KAERI

    International Nuclear Information System (INIS)

    In order to enhance the throughput of a pyro-processing in which electrochemical processes are mostly engaged, the design of a continuous concept is required. The graphite cathode in the electro-refiner enables the uranium deposit on the cathodes to be stripped off spontaneously, resulting in a continuous reaction. The collected uranium deposits at the bottom of the inner cone of the reactor are transferred by a conveyor. The residuals in the anode basket after the uranium is depleted are noble metals. These are also collected at the bottom of the outer shell of the reactor, and conveyed from the reactor for a further treatment. This work addresses the design of the electro-refiner for a continuous operation. The behavior of particles such as uranium dendrites or noble metals was analyzed to achieve the proper operating conditions. The operating conditions for the cathode processor in which molten salt is distilled were also investigated. (authors)

  1. ADVANCED OXIDATION PROCESS TECHNOLOGY (ULTRAVIOLET RADIATION/OZONE TREATMENT) FOR REMOVAL OF METHYL TERTIARY BUTYL ETHER (MTBE) IN GROUND WATER SUPPLIES.

    Science.gov (United States)

    U.S. EPA’s Office of Research and Development in Cincinnati, Ohio has been testing and evaluating MTBE removal in dechlorinated tap water using three oxidant combinations: hydrogen peroxide/ozone, ultraviolet irradiation (UV)/ozone, and UV/ozone/hydrogen peroxide. Pilot-scale st...

  2. Traditional machining processes research advances

    CERN Document Server

    2015-01-01

    This book collects several examples of research in machining processes. Chapter 1 provides information on polycrystalline diamond tool material and its emerging applications. Chapter 2 is dedicated to the analysis of orthogonal cutting experiments using diamond-coated tools with force and temperature measurements. Chapter 3 describes the estimation of cutting forces and tool wear using modified mechanistic models in high performance turning. Chapter 4 contains information on cutting under gas shields for industrial applications. Chapter 5 is dedicated to the machinability of magnesium and its alloys. Chapter 6 provides information on grinding science. Finally, chapter 7 is dedicated to flexible integration of shape and functional modelling of machine tool spindles in a design framework.    

  3. Advanced Purex process for the new French reprocessing plants

    International Nuclear Information System (INIS)

    The paper describes the main process innovations of the new Cogema reprocessing plants of La Hague (UP3 and UP2 800). Major improvements of process like the use of rotary dissolvers and annular columns, and also entirely new processes like solvent distillation and plutonium oxidizing dissolution, yield an advanced Purex process. The results of these innovations are significant improvements for throughput, end-products purification performances and waste minimization. They contribute also to limit personnel exposure. The main results of the first three years of operation are described. (author). 3 refs., 5 figs

  4. Advanced materials for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, T.R.; Stevenson, J.

    1995-08-01

    The purpose of this research is to improve the properties of the current state-of-the-art materials used for solid oxide fuel cells (SOFCs). The objectives are to: (1) develop materials based on modifications of the state-of-the-art materials; (2) minimize or eliminate stability problems in the cathode, anode, and interconnect; (3) Electrochemically evaluate (in reproducible and controlled laboratory tests) the current state-of-the-art air electrode materials and cathode/electrolyte interfacial properties; (4) Develop accelerated electrochemical test methods to evaluate the performance of SOFCs under controlled and reproducible conditions; and (5) Develop and test materials for use in low-temperature SOFCs. The goal is to modify and improve the current state-of-the-art materials and minimize the total number of cations in each material to avoid negative effects on the materials properties. Materials to reduce potential deleterious interactions, (3) improve thermal, electrical, and electrochemical properties, (4) develop methods to synthesize both state-of-the-art and alternative materials for the simultaneous fabricatoin and consolidation in air of the interconnections and electrodes with the solid electrolyte, and (5) understand electrochemical reactions at materials interfaces and the effects of component composition and processing on those reactions.

  5. Advanced oxidation of acid and reactive dyes

    DEFF Research Database (Denmark)

    Arslan-Alaton, I.; Gursoy, B.H.; Schmidt, Jens Ejbye

    2008-01-01

    The effect of untreated and Fenton-treated acid dyes (C.I. Acid Red 183 and C.I. Acid Orange 51) and a reactive dye (C.I. Reactive Blue 4) on aerobic, anoxic and anaerobic processes was investigated. The optimum Fe2+:H2O2 molar ratio was selected as 1:5 (4:hsp sp="0.25" mM:20:hsp sp="0.25"mM) for...... 10:hsp sp="0.25" min Fenton treatment at pH 3, resulting in reduced chemical oxygen demand and dissolved organic carbon removal efficiencies; only acetate was detected as a stable dye oxidation end product. During anaerobic digestion, 100, 29% and no inhibition in methane production was observed for...... the untreated blue, red and orange dyes, respectively. The inhibitory effect of the blue reactive dye on methane production was ∼21% after Fenton treatment. Neither untreated nor treated dyes exhibited an inhibitory effect on denitrification. Aerobic glucose degradation was inhibited by 23-29% by...

  6. Advances in understanding of transparent conducting oxides

    International Nuclear Information System (INIS)

    The band structures of some transparent conducting oxides are calculated using the screened exchange hybrid functional. The optical properties and band gaps of the CuAlO2 defossalite family follow the expected chemical trends. The limits to the doping of n- and p-type oxides are examined in terms of the dopant compensation by native defects. The accessible range of the Fermi energy under doping is that for which compensating native defects have a positive formation energy. These energy limits are aligned on a band offset diagram. N-dopable oxides have a conduction band minimum that lies deep below the vacuum level, while p-dopable oxides have a valence band top that lies high towards the vacuum level. The nature of electron conduction in amorphous InGaZnOx type oxides is discussed, in terms of the nature of localisation and the density of states at the mobility edge.

  7. Evaluation of advanced hot conditioning process for PHWRS

    International Nuclear Information System (INIS)

    Hot-conditioning/hot functional test process is carried out to the PHT system of reactor before reactor going to critical/operational. The process is aimed in checking the component functionalities at high temperature and high pressure conditions, the process also checks/removes the suspended corrosion products in heat transport circuit. This process leads to formation of a passive or corrosion oxide film on the heat transport circuit surfaces which protects/mitigates the corrosion of the system circuits during the operation of plant. Major concerned alloy in the Primary Heat Transport (PHT) system of Indian PHWRs during the hot conditioning process and also during operation is the carbon steel due to its high corrosion. Hot-conditioning process mitigates the corrosion of carbon steel by the formation of iron oxide (Fe3O4) as major oxide phase layer on the carbon steel surface with a typical thickness of 1.0 μm with particle size of 1μm after 336 h of process at 250 °C. But this passive oxide film thickness increase with time of operation of system with c.a. 10μm for 2.2 EFYP. The protectiveness of passive layer can be further enhanced by reducing the particle sizes in the passive film to nano meter range. The process can impact on the compactness of passive oxide layer with reduced pores in the oxide layer and properties of the nano nature oxide (transport properties) impacting the corrosion mitigation. The corrosion mitigation reduce the source term in the activated corrosion product generation. To achieve this a new process 'Advanced hot conditioning' was developed in water steam chemistry division, BARC for getting a passive oxide film with a lowered particle size in the passive film. The AHC process with 1g/L of PEG-8000 at 250 °C for 336 h showed a particle size <100 nm. The process was tested under the normal operating conditions as function of the time, the corrosion parameter like oxide film thickness, corrosion rate and metal ion release to

  8. VUV/UV/Chlorine as an Enhanced Advanced Oxidation Process for Organic Pollutant Removal from Water: Assessment with a Novel Mini-Fluidic VUV/UV Photoreaction System (MVPS).

    Science.gov (United States)

    Li, Mengkai; Qiang, Zhimin; Hou, Pin; Bolton, James R; Qu, Jiuhui; Li, Peng; Wang, Chen

    2016-06-01

    Vacuum ultraviolet (VUV) and ultraviolet (UV)/chlorine processes are regarded as two of many advanced oxidation processes (AOPs). Because of the similar cost of VUV/UV and UV lamps, a combination of VUV and UV/chlorine (i.e., VUV/UV/chlorine) may enhance the removal of organic pollutants in water but without any additional power input. In this paper, a mini-fluidic VUV/UV photoreaction system (MVPS) was developed for bench-scale experiments, which could emit both VUV (185 nm) and UV (254 nm) or solely UV beams with a nearly identical UV photon fluence. The photon fluence rates of UV and VUV output by the MVPS were determined to be 8.88 × 10(-4) and 4.93 × 10(-5) einstein m(-2) s(-1), respectively. The VUV/UV/chlorine process exhibited a strong enhancement concerning the degradation of methylene blue (MB, a model organic pollutant) as compared to the total performance of the VUV/UV and UV/chlorine processes, although the photon fluence of the VUV only accounted for 5.6% of that of the UV. An acidic pH favored MB degradation by the VUV/UV/chlorine process. The synergistic mechanism of the VUV/UV/chlorine process was mainly ascribed to the effective use of (•)OH for pollutant removal through formation of longer-lived secondary radicals (e.g., (•)OCl). This study demonstrates that the new VUV/UV/chlorine process, as an enhanced AOP, can be applied as a highly effective and energy-saving technology for small-scale water and wastewater treatment. PMID:27187747

  9. Advanced digital signal processing and noise reduction

    CERN Document Server

    Vaseghi, Saeed V

    2008-01-01

    Digital signal processing plays a central role in the development of modern communication and information processing systems. The theory and application of signal processing is concerned with the identification, modelling and utilisation of patterns and structures in a signal process. The observation signals are often distorted, incomplete and noisy and therefore noise reduction, the removal of channel distortion, and replacement of lost samples are important parts of a signal processing system. The fourth edition of Advanced Digital Signal Processing and Noise Reduction updates an

  10. Application of Water Sample Pretreatment by Combined Advanced Oxidation Processes to Determination of Total Phosphorus in Water%组合高级氧化水样预处理在水质总磷检测中的应用

    Institute of Scientific and Technical Information of China (English)

    丁明军; 张军军; 杨慧中; 李清

    2012-01-01

    In determination of total phosphorus in water, comparing with the traditional national standard method, which needs adding potassium persulfate for digestion under high pressure, there are many advantages by using combined advanced oxidation processes to pretreat the water samples, such as simple operation, fast digestion, without addition of chemical reagents, no secondary pollution and convenient on-line monitoring. The experimental results show that the total phosphorus in water samples is oxidized completely and stably by this method. The test results after oxidation are consistent with the national standard method (GB 11893 -1989). This environmentally friendly green pretreatment technology has a good practicality value for water quality on-line monitoring system.%在水样总磷含量的测定中,采用组合高级氧化技术对水样进行预处理,与传统国标法添加过硫酸钾高压消解相比,具有操作简单、消解速度快、无需添加化学试剂、无二次污染、便于实现水质总磷的在线检测等优点.通过试验分析对比,用本方法对水样总磷氧化消解则完全、稳定,测量结果与国标法( GB 11893-1989)消解后测量结果基本一致,是一种“环境友好型”的绿色水处理技术,应用于在线监测系统中具有良好的实用价值.

  11. Chemical System Decontamination at PWR Power Stations Biblis A and B by Advanced System Decontamination by Oxidizing Chemistry (ASDOC-D) Process Technology - 13081

    International Nuclear Information System (INIS)

    For chemical decontamination of PWR primary systems the so called ASDOC-D process has been developed and qualified at the German PWR power station Biblis. In comparison to other chemical decontamination processes ASDOC-D offers a number of advantages: - ASDOC-D does not require separate process equipment but is completely operated and controlled by the nuclear site installations. Feeding of chemical concentrates into the primary system is done by means of the site's dosing systems. Process control is performed by standard site instrumentation and analytics. - ASDOC-D safely prevents any formation and precipitation of insoluble constituents - Since ASDOC-D is operated without external equipment there is no need for installation of such equipment in high radioactive radiation surrounding. The radioactive exposure rate during process implementation and process performance may therefore be neglected in comparison to other chemical decontamination processes. - ASDOC-D does not require auxiliary hose connections which usually bear high leakage risk. The above mentioned technical advantages of ASDOC-D together with its cost-effectiveness gave rise to Biblis Power station to agree on testing ASDOC-D at the volume control system of PWR Biblis unit A. By involving the licensing authorities as well as expert examiners into this test ASDOC-D received the official qualification for primary system decontamination in German PWR. As a main outcome of the achieved results NIS received contracts for full primary system decontamination of both units Biblis A and B (each 1.200 MW) by end of 2012. (authors)

  12. Implementation of advanced electrochemical oxidation for radiochemical concentrate treatment

    International Nuclear Information System (INIS)

    Water treatments in Nuclear Power Plants include ion exchange, evaporation and mechanical filtration techniques. These technologies are used to control the chemical release and to treat coolant in light water reactor types from chemicals and most importantly, from radioactive nuclides. Most of the conventional methods are efficient, but at the same time producing aqueous concentrates with high organic load. Before final storage, the level of organic content of those concentrates must be reduced. Advanced electrochemical oxidation with Boron Doped Diamond (BDD) electrodes are being investigated in laboratory- and pilot scale for treatment of dilute and concentrated aqueous waste streams at Vattenfall-Ringhals NPP. BDD anodes and cathodes are having high over potential against water electrolysis, and therefore well suitable for oxidation of organics. Dilute wastewater, such as laundry water, which has an initial COD level of around 500 mg/l, was reduced to a level of < 20 mg/l in the laboratory. Evaporator concentrates, with a TS content of 3% and pH of 7-8, were treated in pilot scale of 800 liters, working in batch operation mode, at temperatures between 25-50 deg. C. Initial COD levels between 2500 and 8000 mg/l in concentrate was reduced to < 100 mg/l at the first tests and later to < 300 mg/l. The advanced electrochemical oxidation is proven to be a promising technique for radioactive concentrate treatment. Long-term operation is still ongoing to evaluate the performance of the electrodes, cell components and overall process efficiency. (authors)

  13. Detoxification of azinophos methyl using gamma radiation mediated advance oxidation process and investigation of degradation products by HPLC and GC-MS

    International Nuclear Information System (INIS)

    Gamma radiolytic degradation of azinophos-methyl was studied in water and methanol separately, using 60Co as a radiation source under varied experimental conditions. Solution of azinophos-methyl was prepared in pure methanol at concentration of 50 μg ml-1, irradiated at gamma dose of 1 to 7 kGy and high performance liquid chromatography (HPLC) coupled with diode array detector was used to monitor the extent of degradation along with numbers of degradation products. At dose of 7 kGy ≥ 99% of azinophos-methyl was degraded. The degradation occurred by interaction of CH3O x and H x radicals generated by the radiolysis of high purity methanol while in water by x OH radical. The degradation in water was increased by 30% than in methanol due the high oxidation potential of x OH while keeping the gamma ray dose constant at 3 kGy. The generated degradation products were identified using GC-MS and their possible transformation pathways are proposed. It is suggested that use of ionization radiations can be an effective and efficient tool for the removal of organophosphate pesticides in waste water.

  14. Advances in radiation processing of polymeric materials

    International Nuclear Information System (INIS)

    In this paper we review recent advances in industrial applications of electron-beam irradiation in the field of polymer processing at the Takasaki Radiation Chemistry Research Establishment (TRCRE) of JAERI (Japan Atomic Energy Research Institute), and the Whiteshell Laboratories of AECL Research, Canada. Irradiation of a substrate with ionizing radiation produces free radicals through ionization and excitation events. The subsequent chemistry of these radicals is used in radiation processing as a substitute for conventional processing techniques based on heating and/or the addition of chemicals. The advantages of radiation processing include the formation of novel products with desirable material properties, favourable overall process economics and, often, environmental benefits

  15. An investigation of inhibition effect of metronidazole before and after using advanced oxidation process (UV254/H2O2 on specific methanogenic activity of anaerobic biomass

    Directory of Open Access Journals (Sweden)

    S. A. Mirzaee

    2014-07-01

    Conclusion: Different concentrations of metronidazole had an inhibition effect on anaerobic digestions and therefore the efficient pretreatment method is needed to reduce this inhibition effect. The UV254/H2O2 process is an effective method for degradation and conversion of metronidazole to more biodegradable compounds for anaerobic bacteria consumption and, in turn, to increase biogasproduction in anaerobic digestions.

  16. Ion beam processing of advanced electronic materials

    Energy Technology Data Exchange (ETDEWEB)

    Cheung, N.W.; Marwick, A.D.; Roberto, J.B. (eds.) (California Univ., Berkeley, CA (USA); International Business Machines Corp., Yorktown Heights, NY (USA). Thomas J. Watson Research Center; Oak Ridge National Lab., TN (USA))

    1989-01-01

    This report contains research programs discussed at the materials research society symposia on ion beam processing of advanced electronic materials. Major topics include: shallow implantation and solid-phase epitaxy; damage effects; focused ion beams; MeV implantation; high-dose implantation; implantation in III-V materials and multilayers; and implantation in electronic materials. Individual projects are processed separately for the data bases. (CBS)

  17. Ion beam processing of advanced electronic materials

    International Nuclear Information System (INIS)

    This report contains research programs discussed at the materials research society symposia on ion beam processing of advanced electronic materials. Major topics include: shallow implantation and solid-phase epitaxy; damage effects; focused ion beams; MeV implantation; high-dose implantation; implantation in III-V materials and multilayers; and implantation in electronic materials. Individual projects are processed separately for the data bases

  18. Process simulation for advanced composites production

    Energy Technology Data Exchange (ETDEWEB)

    Allendorf, M.D.; Ferko, S.M.; Griffiths, S. [Sandia National Labs., Livermore, CA (United States)] [and others

    1997-04-01

    The objective of this project is to improve the efficiency and lower the cost of chemical vapor deposition (CVD) processes used to manufacture advanced ceramics by providing the physical and chemical understanding necessary to optimize and control these processes. Project deliverables include: numerical process models; databases of thermodynamic and kinetic information related to the deposition process; and process sensors and software algorithms that can be used for process control. Target manufacturing techniques include CVD fiber coating technologies (used to deposit interfacial coatings on continuous fiber ceramic preforms), chemical vapor infiltration, thin-film deposition processes used in the glass industry, and coating techniques used to deposit wear-, abrasion-, and corrosion-resistant coatings for use in the pulp and paper, metals processing, and aluminum industries.

  19. Advanced Methods of Biomedical Signal Processing

    CERN Document Server

    Cerutti, Sergio

    2011-01-01

    This book grew out of the IEEE-EMBS Summer Schools on Biomedical Signal Processing, which have been held annually since 2002 to provide the participants state-of-the-art knowledge on emerging areas in biomedical engineering. Prominent experts in the areas of biomedical signal processing, biomedical data treatment, medicine, signal processing, system biology, and applied physiology introduce novel techniques and algorithms as well as their clinical or physiological applications. The book provides an overview of a compelling group of advanced biomedical signal processing techniques, such as mult

  20. DEGRADATION OF CAFFEINE AND METHYLENE BLUE BY ADVANCED OXIDATION PROCESSES (AOPs = DEGRADAÇÃO DE CAFEÍNA E AZUL DE METILENO POR PROCESSOS OXIDATIVOS AVANÇADOS (POA

    Directory of Open Access Journals (Sweden)

    Enelton Fagnani

    2013-01-01

    Full Text Available The degradation of two compounds of pharmaceutical interest, caffeine (CAF and methylene blue (MB, was studied using physical process (photolysis-UV254nm, chemical process (peroxidation-H2O2 and advanced oxidation processes: photoperoxidation (UV/H2O2, Fenton's reagent (Fe(II/H2O2, photo-Fenton (Fe(II/H2O2/UV and heterogeneous photocatalysis (UV/TiO2. The aqueous samples were recirculated in the photoreactor and the processes were monitored using scanning spectrophotometry in the UV-Vis region and analysis of dissolved organic carbon (DOC. The advanced oxidation processes were more effective in modifying the structure of molecules and the reduction of DOC than the physical or chemical processes. The photo-Fenton process (120 min was the most efficient and the DOC reduction was about 75, 85, and 81% for CAF, MB, and CAF/MB solution, respectively. Thus, the photo-Fenton process was the most efficient in the degradation of substances assayed, followed by heterogeneous photocatalysis. = No presente trabalho foi feita uma avaliação da degradação de dois compostos de interesse farmacêutico, a cafeína (CAF e o azul de metileno (AZM, por vários processos: físico (fotólise-UV254nm; químico (peroxidação-H2O2 e oxidativos avançados, empregando-se a fotoperoxidação (UV/H2O2, o reagente de Fenton (Fe (II /H2O2, o foto-Fenton (Fe (II /H2O2/UV e a fotocatálise heterogênea (UV/TiO2. As amostras aquosas foram recirculadas em um fotorreator de bancada e o monitoramento de cada um dos processos foi realizado usando-se a espectrofotometria de varredura na região do UV-Vis e a análise de carbono orgânico dissolvido (COD. Os processos oxidativos avançados foram mais eficientes na modificação da estrutura de ambas as moléculas e na redução da concentração de COD. Em 120 min. de ensaio com o processo foto-Fenton, o mais eficiente, houve uma redução de COD de 75, 85, e 81% para a CAF, AZM, e a solução composta por ambos, respectivamente

  1. Plutonium Oxide Process Capability Work Plan

    Energy Technology Data Exchange (ETDEWEB)

    Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tingey, Joel M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-02-28

    Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

  2. Plutonium Oxide Process Capability Work Plan

    International Nuclear Information System (INIS)

    Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

  3. A novel advanced oxidation process——wet electrocatalytic oxidation for high concentrated organic wastewater treatment

    Institute of Scientific and Technical Information of China (English)

    DAI QiZhou; ZHOU MingHua; LEI LeCheng; ZHANG Xing Wang

    2007-01-01

    A novel advanced oxidation process-wet electrocatalytic oxidation(WEO)was studied with p-nitrophenol as model pollutant and β-PbO2 electrode as the anode.Compared with the effect of the individual wet air oxidation(WAO)and electrochemical oxidation(EO),the effect of WEO showed synergistic effect on COD removal under the conditions of temperature 160℃,C=1000mg·L-1,PN2=0.50MPa,Po2=0.9 MPa,current density=3 mA·cm-2,Na2SO4 3 g·L-1.And the synergistic factor got the best value of 0.98 within 120 min after 180 min treatment.The synergistic factor was studied after 120 min treatment at 100℃,120℃,140℃and 160℃,and the effect of 120℃was the best with the value of 1.26.Possible mechanism for the synergistic effect was discussed based on the analysis of free-radical generation and intermediates detected by HPLC and GC/MS.

  4. Analytical evaluation and optimization of advanced oxidation process in a solar pilot power plant; Evaluacion analitica y optimizacion de procesos de oxidacion avanzada en planta piloto solar

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Vazquez, J.; Malato Rodriguez, S.; Rodriguez Fernandez-Alba, A.

    2003-07-01

    The technical feasibility mechanisms and performance of degradation of several pesticides (imidacloprid, methomyl and diuron) dissolved in water have been studies at pilot scale in two well-defined photocatalytic systems of special interest because natural UV light can be used: heterogeneous photocatalysis with titanium dioxide and homogeneous photocatalysis by photo-Fenton.Equivalent pilot-scale (made up of Compound Parabolic Collectors (CPCs) specially designed for solar photocatalytic applications) and field conditions used for both systems and the three pesticides allowed adequate comparison of the degree of mineralization and toxicity achieved as well as the transformation products generated en route to mineralization. Total disappearance of the parent compounds and 90% mineralisation have been attained with all pesticides tested, methomyl being the most difficult to be degraded with both treatments. First order rate constants, initial rate,time necessary for mineralizing 90% of the initial TOC and hydrogen peroxide consumption were calculated in all cases, enabling comparison both of treatments and of the selected pesticide reactivity. Complete mineralisation of TOC is not achieved even after quite a long time (more than 300 minutes). Three different bioassays (Vibrio fischeri, Daphnia magna and a Microalga) have been used for testing the progress of toxicity during treatments. All remained toxic down to very low pesticide disappearance of the pesticide. Only if treatment is maintained throughout enough mineralisation (i. e. TOC disappearance), the toxicity is reduced to below the threshold (EC 50%). Transformation products evaluated by GC-MS/AED (after two SPE procedures), LC-IT-MS and LC-IC were the same in both phototreatments. The main differences between the two processes are in the amount of transformation products (TPs) generated, not in the TPs detected which were always the same. (Author)

  5. Shielding analysis of the advanced voloxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Je; Park, J. J.; Lee, J. W.; Shin, J. M.; Park, G. I.; Song, K. C

    2008-09-15

    This report deals describes how much a shielding benefit can be obtained by the Advanced Voloxidation process. The calculation was performed with the MCNPX code and a simple problem was modeled with a spent fuel source which was surrounded by a concrete wall. The source terms were estimated with the ORIGEN-ARP code and the gamma spectrum and the neutron spectrum were also obtained. The thickness of the concrete wall was estimated before and after the voloxidation process. From the results, the gamma spectrum after the voloxidation process was estimated as a 67% reduction compared with that of before the voloxidation process due to the removal of several gamma emission elements such as cesium and rubidium. The MCNPX calculations provided that the thickness of the general concrete wall could be reduced by 12% after the voloxidation process. And the heavy concrete wall provided a 28% reduction in the shielding of the source term after the voloxidation process. This can be explained in that there lots of gamma emission isotopes still exist after the advanced voloxidation process such as Pu-241, Y-90, and Sr-90 which are independent of the voloxidation process.

  6. Advances in image processing and pattern recognition

    International Nuclear Information System (INIS)

    The conference papers reported provide an authorative and permanent record of the contributions. Some papers are more theoretical or of review nature, while others contain new implementations and applications. They are conveniently grouped into the following 7 fields (after a general overview): Acquisition and Presentation of 2-D and 3-D Images; Static and Dynamic Image Processing; Determination of Object's Position and Orientation; Objects and Characters Recognition; Semantic Models and Image Understanding; Robotics and Computer Vision in Manufacturing; Specialized Processing Techniques and Structures. In particular, new digital image processing and recognition methods, implementation architectures and special advanced applications (industrial automation, robotics, remote sensing, biomedicine, etc.) are presented. (Auth.)

  7. Can sample treatments based on advanced oxidation processes assisted by high-intensity focused ultrasound be used for toxic arsenic determination in human urine by flow-injection hydride-generation atomic absorption spectrometry?

    Science.gov (United States)

    Correia, A; Galesio, M; Santos, H; Rial-Otero, R; Lodeiro, C; Oehmen, A; Conceição, Antonio C L; Capelo, J L

    2007-05-15

    Two advanced oxidation processes (AOPs), based on high-intensity focused ultrasound (HIFU), namely, KMnO(4)/HCl/HIFU and H(2)O(2)/HCl/HIFU are studied and compared for the determination of toxic arsenic in human urine [As(III)+As(V)+MMA+DMA] by flow-injection hydride-generation atomic absorption spectrometry (FI-HG-AAS). The KMnO(4)/HCl/HIFU procedure was found to be adequate for organic matter degradation in human urine. l-cysteine (letra minuscula) was used for As reduction to the trivalent state. The new procedure was assessed with seven urines certified in different As species. Results revealed that with KMnO(4)/HCl/HIFU plus l-cysteine the toxic arsenic can be accurately measured in human urine whilst the H(2)O(2)/HCl/HIFU procedure underestimates toxic As. DMA and MMA degradation in urine were observed, due to the effects of the ultrasonic field. Recoveries for As(III), As(V), MMA and DMA were within the certified ranges. Arsenobetaine was not degraded by the AOPs. The new procedure adheres well to the principles of analytical minimalism: (i) low reagent consumption, (ii) low reagent concentration, (iii) low waste production and (iv) low amount of time required for sample preparation and analysis. PMID:19071711

  8. Oxidation process of lanthanum hexaboride ceramics

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Oxidation process of lanthanum hexaboride (LaB6) ceramic powder was investigated . The LaB6 powder samples were heated continually from room temperature to 1 473 K at a heating rate of 10 K/min by differential scanning calorimetry. The oxidation tests were conducted at different exposure temperatures. The phases and morphologies of the samples before and after exposure were analyzed by XRD and SEM. It was pointed out that before 1 273 K, LaB6 has high oxidation resistant ability, which was due to that the oxide layer hinders the oxygen diffusion from outer to the surface of LaB6 grains. The oxide layer was composed of the transition phases, which were composed of La2O3 and B2O3 formed from the initial oxidation; when the oxidation temperature exceeded 1 273 K, protective layer was destroyed due to the vaporization of liquid B2O3. Based on the results of X-ray diffraction analysis, oxidation process of LaB6 ceramic powder can be described as follows: Before 1 273 K, lanthanum borate,La(BO2)3 was formed on the surface of samples, then lanthanum oxide (La2O3) and boron oxide (B2O3) were present on the surface of samples oxidized when the temperature reached to 1 473 K.

  9. Advanced methods for the treatment of organic aqueous wastes: wet air oxidation and wet peroxide oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Debellefontaine, Hubert; Chakchouk, Mehrez; Foussard, Jean Noel [Institut National des Sciences Appliquees (INSA), 31 - Toulouse (France). Dept. de Genie des Procedes Industriels; Tissot, Daniel; Striolo, Phillipe [IDE Environnement S.A., Toulouse (France)

    1993-12-31

    There is a growing concern about the problems of wastes elimination. Various oxidation techniques are suited for elimination of organic aqueous wastes, however, because of the environmental drawbacks of incineration, liquid phase oxidation should be preferred. `Wet Air Oxidation` and `Wet Peroxide Oxidation`are alternative processes which are discussed in this paper. 17 refs., 13 figs., 4 tabs.

  10. Recent Advances in Precombustion Coal Cleaning Processes

    Institute of Scientific and Technical Information of China (English)

    Shiao-HungChiang; DaxinHe

    1994-01-01

    The mineral matter in coal constitutes a major impediment to the direct use of coal in power plants.A concerted effort has been mounted to reduce the ash/sulfur contents in product coal to meet the ever more stringent environmental regulations.In recent years,significant advances have taken place in fine coal cleaning technologies.A review of recent developments in aveanced physical,chemical and biological processes for deep-cleaning of fine coal is presented.

  11. Microwave processing of ceramic oxide filaments. Annual report, FY1997

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, G.J.

    1998-12-31

    The objective of the microwave filament processing project is to develop microwave techniques to manufacture continuous ceramic oxide filaments. Microwave processing uses the volumetric absorption of microwave power in oxide filament tows to drive off process solvents, to burn out organic binders, and to sinter the dried fibers to produce flexible, high-strength ceramic filaments. The technical goal is to advance filament processing technology by microwave heating more rapidly with less energy and at a lower cost than conventional processing, but with the same quality as conventional processing. The manufacturing goal is to collaborate with the 3M Company, a US manufacturer of ceramic oxide filaments, to evaluate the technology using a prototype filament system and to transfer the microwave technology to the 3M Company. Continuous ceramic filaments are a principal component in many advanced high temperature materials like continuous fiber ceramic composites (CFCC) and woven ceramic textiles. The use of continuous ceramic filaments in CFCC radiant burners, gas turbines, waste incineration, and hot gas filters in U.S. industry and power generation is estimated to save at least 2.16 quad/yr by year 2010 with energy cost savings of at least $8.1 billion. By year 2010, continuous ceramic filaments and CFCC`s have the potential to abate pollution emissions by 917,000 tons annually of nitrous oxide and 118 million tons annually of carbon dioxide (DOE Report OR-2002, February, 1994).

  12. Processes regulating nitric oxide emissions from soils

    OpenAIRE

    Pilegaard, Kim

    2013-01-01

    Nitric oxide (NO) is a reactive gas that plays an important role in atmospheric chemistry by influencing the production and destruction of ozone and thereby the oxidizing capacity of the atmosphere. NO also contributes by its oxidation products to the formation of acid rain. The major sources of NO in the atmosphere are anthropogenic emissions (from combustion of fossil fuels) and biogenic emission from soils. NO is both produced and consumed in soils as a result of biotic and abiotic process...

  13. Oxidative processes of desulfurization of liquid

    OpenAIRE

    Campos Martín, José Miguel; Capel Sánchez, María del Carmen; Pérez Presas, Patricia; García Fierro, José Luis

    2010-01-01

    Environmental concerns have introduced a need to remove sulfur-containing compounds from light oil. As oxidative desulfurization is conducted under very mild reaction conditions, much attention has recently been devoted to this process. In this contribution, the developments in selective removal of organosulfur compounds present in liquid fuels via oxidative desulfurization, including both chemical oxidation and biodesulfurization, are reviewed. At the end of each section, a brief ...

  14. Human factors challenges for advanced process control

    International Nuclear Information System (INIS)

    New human-system interface technologies provide opportunities for improving operator and plant performance. However, if these technologies are not properly implemented, they may introduce new challenges to performance and safety. This paper reports the results from a survey of human factors considerations that arise in the implementation of advanced human-system interface technologies in process control and other complex systems. General trends were identified for several areas based on a review of technical literature and a combination of interviews and site visits with process control organizations. Human factors considerations are discussed for two of these areas, automation and controls

  15. Costs of the electrochemical oxidation of wastewaters: a comparison with ozonation and Fenton oxidation processes.

    Science.gov (United States)

    Cañizares, Pablo; Paz, Rubén; Sáez, Cristina; Rodrigo, Manuel A

    2009-01-01

    In the work described here the technical and economic feasibilities of three Advanced Oxidation Processes (AOPs) have been studied: Conductive-Diamond Electrochemical Oxidation (CDEO), Ozonation and Fenton oxidation. The comparison was made by assessing the three technologies with synthetic wastewaters polluted with different types of organic compounds and also with actual wastes (from olive oil mills and from a fine-chemical manufacturing plant). All three technologies were able to treat the wastes, but very different results were obtained in terms of efficiency and mineralization. Only CDEO could achieve complete mineralization of the pollutants for all the wastes. However, the efficiencies were found to depend on the concentration of pollutant (mass transfer control of the oxidation rate). Results obtained in the oxidation with ozone (at pH 12) or by Fenton's reagent were found to depend on the nature of the pollutants, and significant concentrations of oxidation-refractory compounds were usually accumulated during the treatment. Within the discharge limits that all of the technologies can reach, the economic analysis shows that the operating cost of Fenton oxidation is lower than either CDEO or ozonation, although CD\\EO can compete satisfactorily with the Fenton process in the treatment of several kinds of wastes. Likewise, the investment cost for the ozonation process seems to be higher than either CDEO or Fenton oxidation, regardless of the pollutant treated. PMID:18082930

  16. Recent advances in nonlinear speech processing

    CERN Document Server

    Faundez-Zanuy, Marcos; Esposito, Antonietta; Cordasco, Gennaro; Drugman, Thomas; Solé-Casals, Jordi; Morabito, Francesco

    2016-01-01

    This book presents recent advances in nonlinear speech processing beyond nonlinear techniques. It shows that it exploits heuristic and psychological models of human interaction in order to succeed in the implementations of socially believable VUIs and applications for human health and psychological support. The book takes into account the multifunctional role of speech and what is “outside of the box” (see Björn Schuller’s foreword). To this aim, the book is organized in 6 sections, each collecting a small number of short chapters reporting advances “inside” and “outside” themes related to nonlinear speech research. The themes emphasize theoretical and practical issues for modelling socially believable speech interfaces, ranging from efforts to capture the nature of sound changes in linguistic contexts and the timing nature of speech; labors to identify and detect speech features that help in the diagnosis of psychological and neuronal disease, attempts to improve the effectiveness and performa...

  17. Advanced Signal Processing for Wireless Multimedia Communications

    Directory of Open Access Journals (Sweden)

    Xiaodong Wang

    2000-01-01

    Full Text Available There is at present a worldwide effort to develop next-generation wireless communication systems. It is envisioned that many of the future wireless systems will incorporate considerable signal-processing intelligence in order to provide advanced services such as multimedia transmission. In general, wireless channels can be very hostile media through which to communicate, due to substantial physical impediments, primarily radio-frequency interference and time-arying nature of the channel. The need of providing universal wireless access at high data-rate (which is the aim of many merging wireless applications presents a major technical challenge, and meeting this challenge necessitates the development of advanced signal processing techniques for multiple-access communications in non-stationary interference-rich environments. In this paper, we present some key advanced signal processing methodologies that have been developed in recent years for interference suppression in wireless networks. We will focus primarily on the problem of jointly suppressing multiple-access interference (MAI and intersymbol interference (ISI, which are the limiting sources of interference for the high data-rate wireless systems being proposed for many emerging application areas, such as wireless multimedia. We first present a signal subspace approach to blind joint suppression of MAI and ISI. We then discuss a powerful iterative technique for joint interference suppression and decoding, so-called Turbo multiuser detection, that is especially useful for wireless multimedia packet communications. We also discuss space-time processing methods that employ multiple antennas for interference rejection and signal enhancement. Finally, we touch briefly on the problems of suppressing narrowband interference and impulsive ambient noise, two other sources of radio-frequency interference present in wireless multimedia networks.

  18. DEMONSTRATION OF THE HIPOX ADVANCED OXIDATION TECHNOLOGY FOR THE TREATMENT OF MTBE-CONTAMINATED GROUNDWATER

    Science.gov (United States)

    The HiPOx technology is an advanced oxidation process that incorporates high-precision delivery of ozone and hydrogen peroxide to chemically destroy organic contaminants with the promise of minimizing bromate formation. A MTBE-contaminated groundwater from the Ventura County Nav...

  19. Advanced photochemical oxidation of emergent micropollutants: carbamazepine.

    Science.gov (United States)

    Domínguez, Joaquín R; González, Teresa; Palo, Patricia; Cuerda-Correa, Eduardo M

    2014-01-01

    The combination of UV radiation with hydrogen peroxide has been widely used for the photodegradation of pollutants in aqueous solutions. Statistical design of experiments is a powerful tool to optimize this kind of process. Initial hydrogen peroxide concentration, pH and temperature were considered as the variables for the process optimization. The interactions existing between these three variables were analyzed. Initial concentration of hydrogen peroxide proved to be the most important variable conditioning the removal efficiency, followed by temperature, and pH shows a non-significant positive influence along the whole operation interval. The ANOVA test reported significance for five of the nine involved variables. The Response Surface Methodology technique was used to optimize carbamazepine degradation. Under optimal conditions (hydrogen peroxide concentration = 0.38·10(-3) mol L(-1), pH = 1 and temperature = 35.6°C) total carbamazepine degradation was achieved. PMID:24798897

  20. Advanced oxidation for groundwater remediation and for soil decontamination

    International Nuclear Information System (INIS)

    The advanced oxidation process (AOP) used in this paper is based on EB irradiation of water in the presence and absence of ozone. The paper describes two distinct sets of experiments, one dealing with groundwater contaminated with perchloroethylene (PCE) and some genotoxic compounds, and the other dealing with soil contaminated with polycyclic aromatic hydrocarbons (PAHs). The combination of ozone and EB irradiation has shown to be able to mineralize trace amounts of PCE contained in groundwater in a single stage process without formation of any by-product to be disposed of. Moreover, experiments performed with real groundwater have demonstrated that the combined ozone/EB irradiation process is also apt for total removal of some genotoxic compounds detected in groundwater contaminated with PCE. The design of an ozone/EB irradiation plant for treating 108 m3/h is presented. The issue concerning both the occurrences of genotoxic compounds in oxygen containing groundwater and possible processes for their removal is discussed. In the second part soil contaminated with PAHs has been treated in aqueous suspension using ozone and EB irradiation, respectively. Experiments were performed with low contaminated soil (total PAHs about 332 mg/kg soil). With an ozone consumption of 10 g C)3/kg soil a total PAH decomposition of about 21% was recorded. EB irradiation with a reasonable radiation dose of 100 kGy results in about 7% total PAH decomposition at room temperature and about 16%, respectively at 55-60 deg. C. It was recorded that almost no transfer of the PAH takes place from the soil into the water when soil is merely suspended in water. Ozone mainly attacked the high molecular fraction (i.e. consisting of 5 or 6 aromatic rings) of the PAHs investigated while EB irradiation of the aqueous soil suspension mostly decomposed the lower fraction (i.e. consisting up to 4 aromatic rings). (author)

  1. Advanced Plasma Pyrolysis Assembly (PPA) Reactor and Process Development

    Science.gov (United States)

    Wheeler, Richard R., Jr.; Hadley, Neal M.; Dahl, Roger W.; Abney, Morgan B.; Greenwood, Zachary; Miller, Lee; Medlen, Amber

    2012-01-01

    Design and development of a second generation Plasma Pyrolysis Assembly (PPA) reactor is currently underway as part of NASA's Atmosphere Revitalization Resource Recovery effort. By recovering up to 75% of the hydrogen currently lost as methane in the Sabatier reactor effluent, the PPA helps to minimize life support resupply costs for extended duration missions. To date, second generation PPA development has demonstrated significant technology advancements over the first generation device by doubling the methane processing rate while, at the same time, more than halving the required power. One development area of particular interest to NASA system engineers is fouling of the PPA reactor with carbonaceous products. As a mitigation plan, NASA MSFC has explored the feasibility of using an oxidative plasma based upon metabolic CO2 to regenerate the reactor window and gas inlet ports. The results and implications of this testing are addressed along with the advanced PPA reactor development.

  2. Advances in Packaging Methods, Processes and Systems

    Directory of Open Access Journals (Sweden)

    Nitaigour Premchand Mahalik

    2014-10-01

    Full Text Available The food processing and packaging industry is becoming a multi-trillion dollar global business. The reason is that the recent increase in incomes in traditionally less economically developed countries has led to a rise in standards of living that includes a significantly higher consumption of packaged foods. As a result, food safety guidelines have been more stringent than ever. At the same time, the number of research and educational institutions—that is, the number of potential researchers and stakeholders—has increased in the recent past. This paper reviews recent developments in food processing and packaging (FPP, keeping in view the aforementioned advancements and bearing in mind that FPP is an interdisciplinary area in that materials, safety, systems, regulation, and supply chains play vital roles. In particular, the review covers processing and packaging principles, standards, interfaces, techniques, methods, and state-of-the-art technologies that are currently in use or in development. Recent advances such as smart packaging, non-destructive inspection methods, printing techniques, application of robotics and machineries, automation architecture, software systems and interfaces are reviewed.

  3. Advanced monitoring with complex stream processing

    CERN Document Server

    CERN. Geneva

    2015-01-01

    Making sense of metrics and logs for service monitoring can be a complicated task. Valuable information is normally scattered across several streams of monitoring data, requiring aggregation, correlation and time-based analysis to promptly detect problems and failures. This presentations shows a solution which is used to support the advanced monitoring of the messaging services provided by the IT Department. It uses Esper, an open-source software product for Complex Event Processing (CEP), that analyses series of events for deriving conclusions from them.

  4. Processing and properties of advanced metallic foams

    Science.gov (United States)

    Brothers, Alan Harold

    Since the development of the first aluminum foams in the middle of the 20th century [178], great advances have been made in the processing and fundamental understanding of metallic foams. As a result of these advances, metallic foams are now penetrating a number of applications where their unique suite of properties makes them superior to solid materials, such as lightweight structures, packaging and impact protection, and filtration and catalysis [3]. The purpose of this work is to extend the use of metallic foams in such applications by expanding their processing to include more sophisticated base alloys and architectures. The first four chapters discuss replacement of conventional crystalline metal foams with ones made from high-strength, low-melting amorphous metals, a substitution that offers potential for achieving mechanical properties superior to those of the best crystalline metal foams, without sacrificing the simplicity of processing methods made for low-melting crystalline alloys. Three different amorphous metal foams are developed in these chapters, and their structures and properties characterized. It is shown for the first time that amorphous metal foams, due to stabilization of shear bands during bending of their small strut-like features, are capable of compressive ductility comparable to that of ductile crystalline metal foams. A two-fold improvement in mechanical energy absorption relative to crystalline aluminum foams is shown experimentally to result from this stabilization. The last two chapters discuss modifications in foam processing that are designed to introduce controllable and continuous gradients in local foam density, which should improve mass efficiency by mimicking the optimized structures found in natural cellular materials [64], as well as facilitate the bonding and joining of foams with solid materials in higher-order structures. Two new processing methods are developed, one based on replication of nonuniformly-compressed polymer

  5. Development of advanced spent fuel management process

    International Nuclear Information System (INIS)

    This study is to develop an advanced spent fuel management process for countries which have not yet decided a back-end nuclear fuel cycle policy. The aims of this process development based on the pyroreduction technology of PWR spent fuels with molten lithium, are to reduce the storage volume by a quarter and to reduce the storage cooling load in half by the preferential removal of highly radioactive decay-heat elements such as Cs-137 and Sr-90 only. From the experimental results which confirm the feasibility of metallization technology, it is concluded that there are no problems in aspects of reaction kinetics and equilibrium. However, the operating performance test of each equipment on an engineering scale still remain and will be conducted in 1999. (author). 21 refs., 45 tabs., 119 figs

  6. Diffusion-controlled processes in nuclear reactor oxide systems

    International Nuclear Information System (INIS)

    Highlights: ► Pertinent classics in high temperature corrosion are discussed. ► Ni to NiO oxidation model applied in growth of corrosion-resistant films in nuclear reactors. ► Transport processes in amorphous SiO2 in the context of its protective properties. ► Oxide deformation by creep using NiO single crystals showing lattice diffusion control of oxygen. ► Creep in polycrystalline NiO controlled by grain boundary diffusion. - Abstract: Oxide films formed as corrosion products at high temperatures on metallic components of advanced nuclear systems constitute a complex environment in which a wide range of phenomena have usually an important role to play. From this wide range of phenomena, three diffusion-controlled processes are discussed in this paper. The oxidation of Ni to NiO is used as a simple model for studying growth of corrosion-resistant films in nuclear reactors. Transport processes in amorphous SiO2 are then examined in the context of the highly protective properties of SiO2 films. Finally, deformation processes in oxides are discussed again using NiO as an example. The observed creep rates indicate that in single crystals creep is controlled by lattice diffusion of oxygen to allow dislocations climb, whereas in polycrystalline material it is controlled by grain boundary diffusion of oxygen to allow grain boundary sliding and changes in grain shape.

  7. Radiation Processing of Advanced Composite Materials

    International Nuclear Information System (INIS)

    Advanced composites, such as carbon-fiber-reinforced plastics, are being used widely for many applications. Carbon fiber/epoxies composites have attracted special attention from the aircraft, aerospace, marine engineering, sporting goods and transportation industries, because they have useful mechanical properties including high strength-to-weight and stiffness-to-weight ratios, a corrosion resistant, impact and damage tolerance characteristics and wear properties. Thermal curing has been the dominant industrial process for advanced composites until now, however, a radiation curing process using UV, microwave x-ray, electron-beam(E-beam) and γ-ray has emerged as a better alternative in recent years. These processes are compatible with the manufacturing of composites using traditional fabrication methods including a filament/tape winding, pultrusion, resin transfer moulding and hand lay-up. In this study, E-beam curable carbon fiber/epoxy composites were manufactured, and their mechanical properties were investigated. Two epoxy resins (bisphenol-A, bisphenol-F) containing photo-initiators (tri aryl sulfonium hexafluorophosphate, tri aryl sulfonium hexafluoroantimonate) were used as a matrix and a 4H-satin carbon woven fabric was used as a reinforcement. And then an electron beam irradiated the composites up to 200 kGy in a vacuum and an inert atmosphere. The cure cycle was optimized and the properties of composites were evaluated and analyzed via a differential scanning calorimetry, scanning electron microscopy, sol-gel extractions, FT-NIR, universal test machine, and an impact tester. The gel content, glass transition temperature and mechanical strength of the irradiated composites were increased with an increasing radiation dose

  8. Development of Advanced Spent Fuel Management Process

    International Nuclear Information System (INIS)

    As a part of research efforts to develop an advanced spent fuel management process, this project focused on the electrochemical reduction technology which can replace the original Li reduction technology of ANL, and we have successfully built a 20 kgHM/batch scale demonstration system. The performance tests of the system in the ACPF hot cell showed more than a 99% reduction yield of SIMFUEL, a current density of 100 mA/cm2 and a current efficiency of 80%. For an optimization of the process, the prevention of a voltage drop in an integrated cathode, a minimization of the anodic effect and an improvement of the hot cell operability by a modulation and simplization of the unit apparatuses were achieved. Basic research using a bench-scale system was also carried out by focusing on a measurement of the electrochemical reduction rate of the surrogates, an elucidation of the reaction mechanism, collecting data on the partition coefficients of the major nuclides, quantitative measurement of mass transfer rates and diffusion coefficients of oxygen and metal ions in molten salts. When compared to the PYROX process of INL, the electrochemical reduction system developed in this project has comparative advantages in its application of a flexible reaction mechanism, relatively short reaction times and increased process yields

  9. Development of Advanced Spent Fuel Management Process

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Chung Seok; Choi, I. K.; Kwon, S. G. (and others)

    2007-06-15

    As a part of research efforts to develop an advanced spent fuel management process, this project focused on the electrochemical reduction technology which can replace the original Li reduction technology of ANL, and we have successfully built a 20 kgHM/batch scale demonstration system. The performance tests of the system in the ACPF hot cell showed more than a 99% reduction yield of SIMFUEL, a current density of 100 mA/cm{sup 2} and a current efficiency of 80%. For an optimization of the process, the prevention of a voltage drop in an integrated cathode, a minimization of the anodic effect and an improvement of the hot cell operability by a modulation and simplization of the unit apparatuses were achieved. Basic research using a bench-scale system was also carried out by focusing on a measurement of the electrochemical reduction rate of the surrogates, an elucidation of the reaction mechanism, collecting data on the partition coefficients of the major nuclides, quantitative measurement of mass transfer rates and diffusion coefficients of oxygen and metal ions in molten salts. When compared to the PYROX process of INL, the electrochemical reduction system developed in this project has comparative advantages in its application of a flexible reaction mechanism, relatively short reaction times and increased process yields.

  10. Study of Advanced Oxidation System for Water Treatment

    International Nuclear Information System (INIS)

    Hygiene water is still a big problem globally as well as energy and food, especially in Indonesia where more than 70 % lived in Java island. One of the efforts in treating hygiene water is to recycle the used water. In this case it is needed clean water technology. Many methods have been done, this paper describes the advanced oxidation technology system based on ozone, titania and plasma discharge. (author)

  11. Oxidation of alloys targeted for advanced steam turbines

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, G.R.; Covino, B.S., Jr.; Bullard, S.J.; Ziomek-Moroz, M.; Alman, D.E.

    2006-03-12

    Ultra supercritical (USC) power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy’s Advanced Power Systems Initiatives include coal generation at 60% efficiency, which would require steam temperatures of up to 760°C. This research examines the steamside oxidation of alloys for use in USC systems, with emphasis placed on applications in high- and intermediate-pressure turbines.

  12. Advanced oxidation and adsorption modification of dust waste from standard moulding sands

    OpenAIRE

    A. Baliński

    2010-01-01

    The article discusses the process of advanced oxidation (AO) with application of ultrasounds and surface modification of the dust waste collected during dry dedusting of processed moulding sands with bentonite binder. A beneficial effect of both AO and adsorption modification of dust waste, when performed with the selected type of polyelectrolyte, on the technological and mechanical properties of moulding sands prepared with an addition of this dust has been stated. In spite of the bentonite ...

  13. Advanced Color Image Processing and Analysis

    CERN Document Server

    2013-01-01

    This volume does much more than survey modern advanced color processing. Starting with a historical perspective on ways we have classified color, it sets out the latest numerical techniques for analyzing and processing colors, the leading edge in our search to accurately record and print what we see. The human eye perceives only a fraction of available light wavelengths, yet we live in a multicolor world of myriad shining hues. Colors rich in metaphorical associations make us “purple with rage” or “green with envy” and cause us to “see red.” Defining colors has been the work of centuries, culminating in today’s complex mathematical coding that nonetheless remains a work in progress: only recently have we possessed the computing capacity to process the algebraic matrices that reproduce color more accurately. With chapters on dihedral color and image spectrometers, this book provides technicians and researchers with the knowledge they need to grasp the intricacies of today’s color imaging.

  14. Alloys for advanced steam turbines--Oxidation behavior

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, G.R.

    2007-10-01

    Advanced or ultra supercritical (USC) steam power plants offer the promise of higher efficiencies and lower emissions. Current goals of the U.S. Department of Energy (DOE) include power generation from coal at 60% efficiency, which would require steam temperatures of up to 760°C. Current research on the oxidation of candidate materials for advanced steam turbines is presented with a focus on a methodology for estimating chromium evaporation rates from protective chromia scales. The high velocities and pressures of advanced steam turbines lead to evaporation predictions as high as 5 × 10-8 kg m-2s-1 of CrO2(OH)2(g) at 760°C and 34.5 MPa. This is equivalent to 0.077 mm per year of solid Cr loss.

  15. Development of advanced hot-gas desulfurization processes

    Energy Technology Data Exchange (ETDEWEB)

    Jothimurugesan, K.

    1999-10-14

    Advanced integrated gasification combined cycle (IGCC) power plants nearing completion, such as Sierra-Pacific, employ a circulating fluidized-bed (transport) reactor hot-gas desulfurization (HGD) process that uses 70-180 {micro}m average particle size (aps) zinc-based mixed-metal oxide sorbent for removing H{sub 2}S from coal gas down to less than 20 ppmv. The sorbent undergoes cycles of absorption (sulfidation) and air regeneration. The key barrier issues associated with a fluidized-bed HGD process are chemical degradation, physical attrition, high regeneration light-off (initiation) temperature, and high cost of the sorbent. Another inherent complication in all air-regeneration-based HGD processes is the disposal of the problematic dilute SO{sub 2} containing regeneration tail-gas. Direct Sulfur Recovery Process (DSRP), a leading first generation technology, efficiently reduces this SO{sub 2} to desirable elemental sulfur, but requires the use of 1-3 % of the coal gas, thus resulting in an energy penalty to the plant. Advanced second-generation processes are under development that can reduce this energy penalty by modifying the sorbent so that it could be directly regenerated to elemental sulfur. The objective of this research is to support the near and long term DOE efforts to commercialize the IGCC-HGD process technology. Specifically we aim to develop: optimized low-cost sorbent materials with 70-80 {micro}m average aps meeting all Sierra specs; attrition resistant sorbents with 170 {micro}m aps that allow greater flexibility in the choice of the type of fluidized-bed reactor e.g. they allow increased throughput in a bubbling-bed reactor; and modified fluidizable sorbent materials that can be regenerated to produce elemental sulfur directly with minimal or no use of coal gas The effort during the reporting period has been devoted to development of an advanced hot-gas process that can eliminate the problematic SO{sub 2} tail gas and yield elemental sulfur

  16. REMOVAL OF REMAZOL ROSSO RB DYE FROM AQUEOUS EFFLUENTS BY HOMOGENOUS FENTON OXIDATION PROCESSES

    OpenAIRE

    Carmen Zaharia; Victoria Fedorcea; Adrian Beda; Victor Amarandei; Augustin Muresan

    2014-01-01

    The paper presents some data from our laboratory-setup experiments of homogenous oxidative processes with hydrogen peroxide (i.e. advanced Fenton oxidation processes) applied for Remazol Rosso RB dye-containing aqueous systems, especially textile effluents. Therefore, some different operating parameters (including pH, concentration of dye, H2O2 and ferrous ions, oxidation time, temperature, stirring regime, among its) were tested for determination of the best performance in effluent decolorat...

  17. Advanced sludge reduction and phosphorous removal process

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    An advanced sludge reduction process, i.e. sludge reduction and phosphorous removal process, was developed. The results show that excellent sludge reduction and biological phosphorous removal can be achieved perfectly in this system. When chemical oxygen demand ρ(COD) is 332 - 420 mg/L, concentration of ammonia ρ(NH3-N) is 30 - 40 mg/L and concentration of total phosphorous ρ(TP) is 6.0 - 9.0 mg/L in influent, the system still ensures ρ(COD)<23 mg/L, ρ(NH3-N)<3.2 mg/L and ρ(TP)<0.72 mg/L in effluent. Besides, when the concentration of dissolved oxygen ρ(DO) is around 1.0 mg/L, sludge production is less than 0. 140 g with the consumption of 1 g COD, and the phosphorous removal exceeds 91%. Also, 48.4% of total nitrogen is removed by simultaneous nitrification and denitrification.

  18. Photocatalysis: Oxidative Processes in Water Treatment

    Directory of Open Access Journals (Sweden)

    Roman V. Prihod'ko

    2013-01-01

    Full Text Available The efficiency of various homogeneous and heterogeneous systems photocatalytic processes destructive oxidation of organic compounds of different classes is considered. It is shown that photocatalytic methods can significantly increase the speed and depth (up to complete mineralization of decomposition processes of toxicants. The use of photocatalysis (PC in the creation of low-power water treatment technologies is a promising direction in addressing environmental problems of the hydrosphere.

  19. Teaching an advanced processing course with hands-on projects

    OpenAIRE

    Simar, Aude; International Conference on Materials Education

    2015-01-01

    The present work discusses an advanced processing course with 10 magisterial courses (2h each) where theoretical aspects are covered and three hands-on projects. This advanced manufacturing course follows a basic course reviewing all manufacturing technologies. The courses concern process selection, advanced machining and additive manufacturing. To each of these topics a project is associated where the use of computer technologies for manufacturing is emphasized. The process selection process...

  20. Natural language processing and advanced information management

    Science.gov (United States)

    Hoard, James E.

    1989-01-01

    Integrating diverse information sources and application software in a principled and general manner will require a very capable advanced information management (AIM) system. In particular, such a system will need a comprehensive addressing scheme to locate the material in its docuverse. It will also need a natural language processing (NLP) system of great sophistication. It seems that the NLP system must serve three functions. First, it provides an natural language interface (NLI) for the users. Second, it serves as the core component that understands and makes use of the real-world interpretations (RWIs) contained in the docuverse. Third, it enables the reasoning specialists (RSs) to arrive at conclusions that can be transformed into procedures that will satisfy the users' requests. The best candidate for an intelligent agent that can satisfactorily make use of RSs and transform documents (TDs) appears to be an object oriented data base (OODB). OODBs have, apparently, an inherent capacity to use the large numbers of RSs and TDs that will be required by an AIM system and an inherent capacity to use them in an effective way.

  1. Processing, Microstructure, and Oxidation Behavior of Iron Foams

    Science.gov (United States)

    Park, Hyeji; Noh, Yoonsook; Choi, Hyelim; Hong, Kicheol; Kwon, Kyungjung; Choe, Heeman

    2016-09-01

    With its historically long popularity in major structural applications, the use of iron (Fe) has also recently begun to be explored as an advanced functional material. For this purpose, it is more advantageous to use Fe as a porous structure, simply because it can provide a greater surface area and a higher reaction rate. This study uses a freeze-casting method, which consists of simple and low-cost processing steps, to produce Fe foam with a mean pore size of 10 μm. We examine the influences of various parameters ( i.e., mold bottom temperature, powder content, and sintering time) on the processing of Fe foam, along with its oxidation kinetics at 823 K (550 °C) with various heat-treatment times. We confirm that Fe2O3 and Fe3O4 oxide layers are successfully formed on the surface of Fe foam. With the Fe oxide layers as an active anode material, the Fe foam can potentially be used as a three-dimensional anode current collector for an advanced lithium-ion battery.

  2. Processing, Microstructure, and Oxidation Behavior of Iron Foams

    Science.gov (United States)

    Park, Hyeji; Noh, Yoonsook; Choi, Hyelim; Hong, Kicheol; Kwon, Kyungjung; Choe, Heeman

    2016-06-01

    With its historically long popularity in major structural applications, the use of iron (Fe) has also recently begun to be explored as an advanced functional material. For this purpose, it is more advantageous to use Fe as a porous structure, simply because it can provide a greater surface area and a higher reaction rate. This study uses a freeze-casting method, which consists of simple and low-cost processing steps, to produce Fe foam with a mean pore size of 10 μm. We examine the influences of various parameters (i.e., mold bottom temperature, powder content, and sintering time) on the processing of Fe foam, along with its oxidation kinetics at 823 K (550 °C) with various heat-treatment times. We confirm that Fe2O3 and Fe3O4 oxide layers are successfully formed on the surface of Fe foam. With the Fe oxide layers as an active anode material, the Fe foam can potentially be used as a three-dimensional anode current collector for an advanced lithium-ion battery.

  3. Development of advanced mixed oxide fuels for plutonium management

    International Nuclear Information System (INIS)

    A number of advanced Mixed Oxide (MOX) fuel forms are currently being investigated at Los Alamos National Laboratory that have the potential to be effective plutonium management tools. Evolutionary Mixed Oxide (EMOX) fuel is a slight perturbation on standard MOX fuel, but achieves greater plutonium destruction rates by employing a fractional nonfertile component. A pure nonfertile fuel is also being studied. Initial calculations show that the fuel can be utilized in existing light water reactors and tailored to address different plutonium management goals (i.e., stabilization or reduction of plutonium inventories residing in spent nuclear fuel). In parallel, experiments are being performed to determine the feasibility of fabrication of such fuels. Initial EMOX pellets have successfully been fabricated using weapons-grade plutonium

  4. Destruction of estrogenic activity in water using UV advanced oxidation

    International Nuclear Information System (INIS)

    The transformation of the steroidal Endocrine Disrupting Compounds (EDCs), 17-β-estradiol (E2) and 17-α-ethinyl estradiol (EE2) by direct UV photolysis and UV/H2O2 advanced oxidation was studied from the perspective of the removal of estrogenic activity associated with the compounds. First, experiments were performed to link the oxidation of E2 and EE2 with subsequent reduction in estrogenic activity. No statistically significant difference between removal rates was observed, implying that the oxidation products of E2 and EE2 are not as estrogenic (measured by the Yeast Estrogen Screen (YES)) as the parent compounds. Utilizing the YES, 90% removal of estrogenic activity of E2 and EE2 at environmentally relevant concentrations (∼ 3 μg L-1) was achieved using a combination of 5 mg L-1 H2O2 and a UV fluence of less than 350 mJ cm-2. Thus, these compounds, when considered at environmentally relevant levels, are significantly degraded at much lower UV fluences than previously thought. A steady state OH radical model was used to predict oxidation of EE2 in laboratory and natural waters

  5. Destruction of estrogenic activity in water using UV advanced oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Rosenfeldt, Erik J. [Department of Civil and Environmental Engineering, Duke University, Durham, NC 27708 (United States); Chen, P.J. [Department of Civil and Environmental Engineering, and Integrated Toxicology Program, Nicolas School of Environment and Earth Science, Duke University (United States); Integrated Toxicology Program, Nicolas School of Environment and Earth Science, Duke University (United States); Kullman, Seth [Integrated Toxicology Program, Nicolas School of Environment and Earth Science, Duke University (United States); Linden, Karl G. [Department of Civil and Environmental Engineering, Duke University, Box 90287, 121 Hudson Hall Engineering Building, Durham, NC 27708-0287 (United States)]. E-mail: kglinden@duke.edu

    2007-05-01

    The transformation of the steroidal Endocrine Disrupting Compounds (EDCs), 17-{beta}-estradiol (E2) and 17-{alpha}-ethinyl estradiol (EE2) by direct UV photolysis and UV/H{sub 2}O{sub 2} advanced oxidation was studied from the perspective of the removal of estrogenic activity associated with the compounds. First, experiments were performed to link the oxidation of E2 and EE2 with subsequent reduction in estrogenic activity. No statistically significant difference between removal rates was observed, implying that the oxidation products of E2 and EE2 are not as estrogenic (measured by the Yeast Estrogen Screen (YES)) as the parent compounds. Utilizing the YES, 90% removal of estrogenic activity of E2 and EE2 at environmentally relevant concentrations ({approx} 3 {mu}g L{sup -1}) was achieved using a combination of 5 mg L{sup -1} H{sub 2}O{sub 2} and a UV fluence of less than 350 mJ cm{sup -2}. Thus, these compounds, when considered at environmentally relevant levels, are significantly degraded at much lower UV fluences than previously thought. A steady state OH radical model was used to predict oxidation of EE2 in laboratory and natural waters.

  6. Gas-phase advanced oxidation as an integrated air pollution control technique

    OpenAIRE

    Getachew A. Adnew; Carl Meusinger; Nicolai Bork; Michael Gallus; Mildrid Kyte; Thomas Rosenørn; Johnson, Matthew S.; Vitalijs Rodins

    2016-01-01

    Gas-phase advanced oxidation (GPAO) is an emerging air cleaning technology based on the natural self-cleaning processes that occur in the Earth’s atmosphere. The technology uses ozone, UV-C lamps and water vapor to generate gas-phase hydroxyl radicals that initiate oxidation of a wide range of pollutants. In this study four types of GPAO systems are presented: a laboratory scale prototype, a shipping container prototype, a modular prototype, and commercial scale GPAO installations. The GPAO s...

  7. Technical, economic and environmental evaluation of advanced tertiary treatments for micropollutants removal (oxidation and adsorption)

    OpenAIRE

    Besnault, S.; Martin Ruel, S.; Baig, S; Esperanza, M.; Budzinski, H.; Miege, C.; Boucher, C.; Le Menach, K.; Coquery, M.

    2014-01-01

    International audience Two pilots for tertiary treatment, an advanced oxidation processes (AOP - O3/UV/H2O2) pilot and a granular activated carbon pilot, were tested in three different wastewater treatment plants after a secondary treatment. A total of 64 micropollutants including drugs, pesticides, alkylphenols, PAHs and metals were analysed in the samples at the inlet and the outlet of the pilots. The tertiary treatments studied (ozone, AOP and activated carbon) were efficient for the re...

  8. Simulation for Supporting Scale-Up of a Fluidized Bed Reactor for Advanced Water Oxidation

    OpenAIRE

    Farhana Tisa; Abdul Aziz Abdul Raman; Wan Mohd Ashri Wan Daud

    2014-01-01

    Simulation of fluidized bed reactor (FBR) was accomplished for treating wastewater using Fenton reaction, which is an advanced oxidation process (AOP). The simulation was performed to determine characteristics of FBR performance, concentration profile of the contaminants, and various prominent hydrodynamic properties (e.g., Reynolds number, velocity, and pressure) in the reactor. Simulation was implemented for 2.8 L working volume using hydrodynamic correlations, continuous equation, and simp...

  9. Avaliação do potencial de processos oxidativos avançados para remediação de águas contaminadas com geosmina e 2-MIB Evaluation of advanced oxidation processes for remediation of contamined water with geosmin and 2-MIB

    OpenAIRE

    Adriane Martins de Freitas; Carla Sirtori; Patricio G. Peralta-Zamora

    2008-01-01

    In this work, the efficiency of some homogeneous advanced oxidation processes (UVC/H2O2, Fe2+/H2O2, UVC/Fe2+/H2O2, UVA/Fe2+/H2O2, solar/Fe2+/H2O2) was investigated toward the degradation of geosmin and 2-methylisoborneol (2-MIB). The effect of relevant experimental parameters (ie. pH, Fe2+ and H2O2 concentration) was first investigated by factorial design, using camphor as a model substrate. In the geosmin and 2-MIB degradation studies the Fenton processes assisted by solar and UVA radiation ...

  10. Degradação de corantes ácidos por processos oxidativos avançados usando um reator com disco rotatório de baixa velocidade Acid dyes degradation by advanced oxidation processes using a low-speed rotating disk reactor

    OpenAIRE

    Vilson Bedim Vianna; Alexandre Rodrigues Tôrres; Eduardo Bessa Azevedo

    2008-01-01

    Three technologies were tested (TiO2/UV, H2O2/UV, and TiO2/H2O2/UV) for the degradation and color removal of a 25 mg L-1 mixture of three acid dyes: Blue 9, Red 18, and Yellow 23. A low speed rotating disc reactor (20 rpm) and a H2O2 concentration of 2.5 mmol L-1 were used. The dyes did not significantly undergo photolysis, although they were all degraded by the studied advanced oxidation processes. With the TiO2/H2O2/UV process, a strong synergism was observed (color removal reached 100%). P...

  11. Development of advanced hot-gas desulfurization processes

    Energy Technology Data Exchange (ETDEWEB)

    Jothimurugesan, K.

    1999-04-26

    Advanced integrated gasification combined cycle (IGCC) power plants nearing completion, such as Sierra-Pacific, employ a circulating fluidized-bed (transport) reactor hot-gas desulfurization (HGD) process that uses 70-180 {micro}m average particle size (aps) zinc-based mixed-metal oxide sorbent for removing H{sub 2}S from coal gas down to less than 20 ppmv. The sorbent undergoes cycles of absorption (sulfidation) and air regeneration. The key barrier issues associated with a fluidized-bed HGD process are chemical degradation, physical attrition, high regeneration light-off (initiation) temperature, and high cost of the sorbent. Another inherent complication in all air-regeneration-based HGD processes is the disposal of the problematic dilute SO{sub 2} containing regeneration tail-gas. Direct Sulfur Recovery Process (DSRP), a leading first generation technology, efficiently reduces this SO{sub 2} to desirable elemental sulfur, but requires the use of 1-3% of the coal gas, thus resulting in an energy penalty to the plant. Advanced second-generation processes are under development that can reduce this energy penalty by modifying the sorbent so that it could be directly regenerated to elemental sulfur. The objective of this research is to support the near and long term DOE efforts to commercialize the IGCC-HGD process technology. Specifically we aim to develop: optimized low-cost sorbent materials with 70-80 {micro}m average aps meeting all Sierra specs; attrition resistant sorbents with 170 {micro}m aps that allow greater flexibility in the choice of the type of fluidized-bed reactor e.g. they allow increased throughput in a bubbling-bed reactor; and modified fluidizable sorbent materials that can be regenerated to produce elemental sulfur directly with minimal or no use of coal gas. The effort during the reporting period has been devoted to development of optimized low-cost zinc-oxide-based sorbents for Sierra-Pacific. The sorbent surface were modified to prevent

  12. Container-less processing of oxide superconductors

    International Nuclear Information System (INIS)

    The production of bulk oxide superconductors with high current carrying capability has been hindered by weak connectivity along grain boundaries, large property anisotropy, reactivity with all known containing media, oxygen content and control, and difficulties with phase stability. The present work outlines a melt processing technique developed in order to study the melting and solidification behavior of bulk YBa2Cu3O7-x or 1:2:3 superconductor material. By employing a drop tube and a resistance heated muffle furnace, melting and subsequent solidification of sintered 1:2:3 powder is performed in an oxidizing atmosphere, free from container contamination. Preliminary experiments have yielded two distinct microstructure depending on the relative size of the processed sphere. In this paper microstructural studies, x-ray analysis, superconductivity measurements, and TEM studies are presented

  13. Pharmaceutical removal during managed aquifer recharge with pretreatment by advanced oxidation

    KAUST Repository

    Lekkerkerker-Teunissen, Karin

    2012-10-01

    Organic micropollutants (OMPs) are detected in sources for drinking water and treatment possibilities are investigated. Innovative removal technologies are available such as membrane filtration and advanced oxidation, but also biological treatment should be considered. By combining an advanced oxidation process with managed aquifer recharge (MAR), two complementary processes are expected to provide a hybrid system for OMP removal, according to the multiple barrier approach. Laboratory scale batch reactor experiments were conducted to investigate the removal of dissolved organic carbon (DOC) and 14 different pharmaceutically active compounds (PhACs) from MAR influent water and water subjected to oxidation, under different process conditions. A DOC removal of 10% was found in water under oxic (aerobic) conditions for batch reactor experiments, a similar value for DOC removal was observed in the field. Batch reactor experiments for the removal of PhACs showed that the removal of pharmaceuticals ranged from negligible to more than 90%. Under oxic conditions, seven out of 14 pharmaceuticals were removed over 90% and 12 out of 14 pharmaceuticals were removed at more than 50% during 30 days of experiments. Under anoxic conditions, four out of 14 pharmaceuticals were removed over 90% and eight out of 14 pharmaceuticals were removed at more than 50% over 30 days\\' experiments. Carbamazepine and phenazone were persistent both under oxic and anoxic conditions. The PhACs removal efficiency with oxidized water was, for most compounds, comparable to the removal with MAR influent water. Copyright © IWA Publishing 2012.

  14. Electro-oxidation process for molybdenum concentrates

    Institute of Scientific and Technical Information of China (English)

    FU Jian-gang; ZHONG Hong; BU Xiang-ming; WANG Fu-li

    2005-01-01

    Sodium hypochlorite was used to treat the standard molybdenum concentrates; the oxidization conditions for sodium hypochlorite were investigated, and the electro-oxidation process was performed. The results indicate that in the suitable conditions, such as temperature around 25 ℃, NaCl concentration 4.0 mol/L, mass ratio of ore slurry liquid to solid (mL/mS) 20, electric charge per gram Mo 0.522 C, pH value of original slurry 8, anodic current density 700 A·m-2 (cell potential 2.7-2.9 V), the Mo leaching rate and the current efficiency reach 98% and 36%, respectively. In order to overcome some shortages of the electro-oxidation process, such as low current efficiency, low Mo concentration in the leaching solution, ultrasonic was adopted to intensify the leaching process. The results show that the Mo leaching rate exceeds 98%, current efficiency increases from 36% to 50% and the Mo concentration in the leaching solution reaches about 60 g/L at low mL/mS of 8 and low electric charge of 0.373 C.

  15. Advances in the Partial Oxidation of Methane to Synthesis Gas

    Institute of Scientific and Technical Information of China (English)

    Quanli Zhu; Xutao Zhao; Youquan Deng

    2004-01-01

    The conversion and utilization of natural gas is of significant meaning to the national economy,even to the everyday life of people. However, it has not become a popular industrial process as expected due to the technical obstacles. In the past decades, much investigation into the conversion of methane,predominant component of natural gas, has been carried out. Among the possible routes of methane conversion, the partial oxidation of methane to synthesis gas is considered as an effective and economically feasible one. In this article, a brief review of recent studies on the mechanism of the partial oxidation of methane to synthesis gas together with catalyst development is wherein presented.

  16. Hybrid process for nitrogen oxides reduction

    Energy Technology Data Exchange (ETDEWEB)

    Epperly, W.R.; Sprague, B.N.

    1991-09-10

    This patent describes a process for reducing the nitrogen oxide concentration in the effluent from the combustion of a carbonaceous fuel. It comprises introducing into the effluent a first treatment agent comprising a nitrogenous composition selected from the group consisting of urea, ammonia, hexamethylenetetramine, ammonium salts of organic acids, 5- or 6-membered heterocyclic hydrocarbons having at least one cyclic nitrogen, hydroxy amino hydrocarbons, NH{sub 4}-lignosulfonate, fur-furylamine, tetrahydrofurylamine, hexamethylenediamine, barbituric acid, guanidine, guanidine carbonate, biguanidine, guanylurea sulfate, melamine, dicyandiamide, biuret, 1.1{prime}-azobisformamide, methylol urea, methylol urea-urea condensation product, dimethylol urea, methyl urea, dimethyl urea, calcium cyanamide, and mixtures thereof under conditions effective to reduce the nitrogen oxides concentration and ensure the presence of ammonia in the effluent; introducing into the effluent a second treatment agent comprising an oxygenated hydrocarbon at an effluent temperature of about 500{degrees} F. to about 1600{degrees} F. under conditions effective to oxidize nitric oxide in the effluent to nitrogen dioxide and ensure the presence of ammonia at a weight ratio of ammonia to nitrogen dioxide of about 1:5 to about 5:1; and contacting the effluent with an aqueous scrubbing solution having a pH of 12 or lower under conditions effective to cause nitrogen dioxide to be absorbed therein.

  17. Recent anode advances in solid oxide fuel cells

    Science.gov (United States)

    Sun, Chunwen; Stimming, Ulrich

    Solid oxide fuel cells (SOFCs) are electrochemical reactors that can directly convert the chemical energy of a fuel gas into electrical energy with high efficiency and in an environment-friendly way. The recent trends in the research of solid oxide fuel cells concern the use of available hydrocarbon fuels, such as natural gas. The most commonly used anode material Ni/YSZ cermet exhibits some disadvantages when hydrocarbons were used as fuels. Thus it is necessary to develop alternative anode materials which display mixed conductivity under fuel conditions. This article reviews the recent developments of anode in SOFCs with principal emphasis on the material aspects. In addition, the mechanism and kinetics of fuel oxidation reactions are also addressed. Various processes used for the cost-effective fabrication of anode have also been summarized. Finally, this review will be concluded with personal perspectives on the future research directions of this area.

  18. Importance of glycolysis and oxidative phosphorylation in advanced melanoma

    Directory of Open Access Journals (Sweden)

    Ho Jonhan

    2012-10-01

    Full Text Available Abstract Serum lactate dehydrogenase (LDH is a prognostic factor for patients with stage IV melanoma. To gain insights into the biology underlying this prognostic factor, we analyzed total serum LDH, serum LDH isoenzymes, and serum lactate in up to 49 patients with metastatic melanoma. Our data demonstrate that high serum LDH is associated with a significant increase in LDH isoenzymes 3 and 4, and a decrease in LDH isoenzymes 1 and 2. Since LDH isoenzymes play a role in both glycolysis and oxidative phosphorylation (OXPHOS, we subsequently determined using tissue microarray (TMA analysis that the levels of proteins associated with mitochondrial function, lactate metabolism, and regulators of glycolysis were all elevated in advanced melanomas compared with nevic melanocytes. To investigate whether in advanced melanoma, the glycolysis and OXPHOS pathways might be linked, we determined expression of the monocarboxylate transporters (MCT 1 and 4. Analysis of a nevus-to-melanoma progression TMA revealed that MCT4, and to a lesser extend MCT1, were elevated with progression to advanced melanoma. Further analysis of human melanoma specimens using the Seahorse XF24 extracellular flux analyzer indicated that metastatic melanoma tumors derived a large fraction of energy from OXPHOS. Taken together, these findings suggest that in stage IV melanomas with normal serum LDH, glycolysis and OXPHOS may provide metabolic symbiosis within the same tumor, whereas in stage IV melanomas with high serum LDH glycolysis is the principle source of energy.

  19. Delay oil oxidation during frying process

    International Nuclear Information System (INIS)

    Blend oil (mixed of refined sunflower and soy beans oils 1:1 w/w) containing add 200 ppm of rosemary leaves methanolic extract (rosemary extract) (RE) and 3% refined rice bran oil (RRBO), were used in frying process at 1800 degree c for 5 hrs/ day, four consecutive days to delay oil oxidation during frying. Therefore, rosemary extract (methanolic extract) was analyzed by HPLC technique for identification of flavonoids compounds (as a specific active compounds; gives high protection to frying oil). Physical and chemical properties, including refractive index(RI). Red color unit (R), viscosity, acidity (FFA), peroxide value (PV), iodine value (IV) oxidized fatty acid (OFA), polymer content (PC), total polar components (TPC) and trans fatty acid (TFA) as eliadic acid were determined. The results indicated that; rosemary extract contained about eight flavonoids compounds (hypersoid, rutin, 3-OH flavon, luleotin, kempferol, sakarutin, querectrin and apeginin). Addition of RE or RRBO to frying oil caused delay oil oxidation during frying process compared with frying oil without any addition. Also, the results indicated that rosemary extract was more effective in reducing formation of PV, FFA, OFA, PC, TPC and TFA in frying oil than refined rice bran oil

  20. Reactor process using metal oxide ceramic membranes

    Science.gov (United States)

    Anderson, M.A.

    1994-05-03

    A reaction vessel for use in photoelectrochemical reactions includes as its reactive surface a metal oxide porous ceramic membrane of a catalytic metal such as titanium. The reaction vessel includes a light source and a counter electrode. A provision for applying an electrical bias between the membrane and the counter electrode permits the Fermi levels of potential reaction to be favored so that certain reactions may be favored in the vessel. The electrical biasing is also useful for the cleaning of the catalytic membrane. Also disclosed is a method regenerating a porous metal oxide ceramic membrane used in a photoelectrochemical catalytic process by periodically removing the reactants and regenerating the membrane using a variety of chemical, thermal, and electrical techniques. 2 figures.

  1. Wet oxidation processes for water pollution remediation

    OpenAIRE

    García Molina, Verónica

    2006-01-01

    [eng] The main objective of this work was to test the efficiency of wet oxidation processes when treating several types of aqueous wastes. On one side its performance for the abatement of chloro-organic aromatic toxic pollutants, such as 4-chlorophenol and 2,4-dichlorophenol has been studied. On the other hand, wastewater from pulp and paper mills, which has been reported to be an indirect source of entry of chlorophenols in the aquatic environment, has been investigated. More in detail, it h...

  2. Project T.E.A.M. (Technical Education Advancement Modules). Advanced Statistical Process Control.

    Science.gov (United States)

    Dunlap, Dale

    This instructional guide, one of a series developed by the Technical Education Advancement Modules (TEAM) project, is a 20-hour advanced statistical process control (SPC) and quality improvement course designed to develop the following competencies: (1) understanding quality systems; (2) knowing the process; (3) solving quality problems; and (4)…

  3. Advanced Chemical Reduction of Reduced Graphene Oxide and Its Photocatalytic Activity in Degrading Reactive Black 5

    Directory of Open Access Journals (Sweden)

    Christelle Pau Ping Wong

    2015-10-01

    Full Text Available Textile industries consume large volumes of water for dye processing, leading to undesirable toxic dyes in water bodies. Dyestuffs are harmful to human health and aquatic life, and such illnesses as cholera, dysentery, hepatitis A, and hinder the photosynthetic activity of aquatic plants. To overcome this environmental problem, the advanced oxidation process is a promising technique to mineralize a wide range of dyes in water systems. In this work, reduced graphene oxide (rGO was prepared via an advanced chemical reduction route, and its photocatalytic activity was tested by photodegrading Reactive Black 5 (RB5 dye in aqueous solution. rGO was synthesized by dispersing the graphite oxide into the water to form a graphene oxide (GO solution followed by the addition of hydrazine. Graphite oxide was prepared using a modified Hummers’ method by using potassium permanganate and concentrated sulphuric acid. The resulted rGO nanoparticles were characterized using ultraviolet-visible spectrophotometry (UV-Vis, X-ray powder diffraction (XRD, Raman, and Scanning Electron Microscopy (SEM to further investigate their chemical properties. A characteristic peak of rGO-48 h (275 cm−1 was observed in the UV spectrum. Further, the appearance of a broad peak (002, centred at 2θ = 24.1°, in XRD showing that graphene oxide was reduced to rGO. Based on our results, it was found that the resulted rGO-48 h nanoparticles achieved 49% photodecolorization of RB5 under UV irradiation at pH 3 in 60 min. This was attributed to the high and efficient electron transport behaviors of rGO between aromatic regions of rGO and RB5 molecules.

  4. Development of advanced hot-gas desulfurization processes

    Energy Technology Data Exchange (ETDEWEB)

    Jothimurugesan, K.

    2000-04-17

    Advanced integrated gasification combined cycle (IGCC) power plants nearing completion, such as Sierra-Pacific, employ a circulating fluidized-bed (transport) reactor hot-gas desulfurization (HGD) process that uses 70-180 {micro}m average particle size (aps) zinc-based mixed-metal oxide sorbent for removing H{sub 2}S from coal gas down to less than 20 ppmv. The sorbent undergoes cycles of absorption (sulfidation) and air regeneration. The key barrier issues associated with a fluidized-bed HGD process are chemical degradation, physical attrition, high regeneration light-off (initiation) temperature, and high cost of the sorbent. Another inherent complication in all air-regeneration-based HGD processes is the disposal of the problematic dilute SO{sub 2} containing regeneration tail-gas. Direct Sulfur Recovery Process (DSRP), a leading first generation technology, efficiently reduces this SO{sub 2} to desirable elemental sulfur, but requires the use of 1-3 % of the coal gas, thus resulting in an energy penalty to the plant. Advanced second-generation processes are under development that can reduce this energy penalty by modifying the sorbent so that it could be directly regenerated to elemental sulfur. The objective of this research is to support the near and long term DOE efforts to commercialize the IGCC-HGD process technology. Specifically we aim to develop: optimized low-cost sorbent materials with 70-80 {micro}m average aps meeting all Sierra specs; attrition resistant sorbents with 170 {micro}m aps that allow greater flexibility in the choice of the type of fluidized-bed reactor e.g. they allow increased throughput in a bubbling-bed reactor; and modified fluidizable sorbent materials that can be regenerated to produce elemental sulfur directly with minimal or no use of coal gas. The effort during the reporting period has been devoted to testing the FHR-32 sorbent. FHR-32 sorbent was tested for 50 cycles of sulfidation in a laboratory scale reactor.

  5. Measurement and modeling of advanced coal conversion processes

    Energy Technology Data Exchange (ETDEWEB)

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. (Advanced Fuel Research, Inc., East Hartford, CT (United States)); Smoot, L.D.; Brewster, B.S. (Brigham Young Univ., Provo, UT (United States))

    1992-01-01

    The objectives of this proposed study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines. This report describes progress during twenty second quarter of the program. Specifically, the paper discusses progress in three task areas: (1) Submodel development and evaluation: coal to char chemistry submodel; fundamental high-pressure reaction rate data; secondary reaction of pyrolysis product and burnout submodels; ash physics and chemistry submodel; large particle submodels; large char particle oxidation at high pressures; and SO[sub x]-NO[sub x] submodel development and evaluation; (2) Comprehensive model development and evaluation: integration of advanced submodels into entrained-flow code, with evaluation and documentation; comprehensive fixed-bed modeling review, development evaluation and implementation; and generalized fuels feedstock submodel; and (3) Application of integrated codes: application of generalized pulverized coal comprehensive code and application of fixed-bed code.

  6. Advanced impedance modeling of solid oxide electrochemical cells

    DEFF Research Database (Denmark)

    Graves, Christopher R.; Hjelm, Johan

    2014-01-01

    Impedance spectroscopy is a powerful technique for detailed study of the electrochemical and transport processes that take place in fuel cells and electrolysis cells, including solid oxide cells (SOCs). Meaningful analysis of impedance measurements is nontrivial, however, because a large number of...... modeling parameters are fit to the many processes which often overlap in the same frequency ranges. Also, commonly used equivalent circuit (EC) models only provide zero-dimensional (0-D) approximations of the processes of the two electrodes, electrolyte and gas transport. Employing improved analytical...... electrode and 2-D gas transport models which have fewer unknown parameters for the same number of processes, (ii) use of a new model fitting algorithm, “multi-fitting”, in which multiple impedance spectra are fit simultaneously with parameters linked based on the variation of measurement conditions, (iii...

  7. Advances in heuristic signal processing and applications

    CERN Document Server

    Chatterjee, Amitava; Siarry, Patrick

    2013-01-01

    There have been significant developments in the design and application of algorithms for both one-dimensional signal processing and multidimensional signal processing, namely image and video processing, with the recent focus changing from a step-by-step procedure of designing the algorithm first and following up with in-depth analysis and performance improvement to instead applying heuristic-based methods to solve signal-processing problems. In this book the contributing authors demonstrate both general-purpose algorithms and those aimed at solving specialized application problems, with a spec

  8. Present status of advanced aqueous separation process technology development

    International Nuclear Information System (INIS)

    In 'the Feasibility study on commercialized fast reactor cycle systems' begun in 1999, the commercialized candidate concept of the process as the advanced aqueous reprocessing system has been examined. This process, named NEXT, includes such advanced process elements as high efficiency dissolution, crystallization, U/Pu/Np co-recovery, and MA recovery. Small scale hot tests of these process elements have been conducted with irradiated fuel of the experimental Fast Reactor 'JOYO' in Chemical Processing Facility (CPF). The prospect of the technical feasibility of the NEXT process is being obtained as a promising candidate concept. (author)

  9. Recent advances in imaging subcellular processes.

    Science.gov (United States)

    Myers, Kenneth A; Janetopoulos, Christopher

    2016-01-01

    Cell biology came about with the ability to first visualize cells. As microscopy techniques advanced, the early microscopists became the first cell biologists to observe the inner workings and subcellular structures that control life. This ability to see organelles within a cell provided scientists with the first understanding of how cells function. The visualization of the dynamic architecture of subcellular structures now often drives questions as researchers seek to understand the intricacies of the cell. With the advent of fluorescent labeling techniques, better and new optical techniques, and more sensitive and faster cameras, a whole array of questions can now be asked. There has been an explosion of new light microscopic techniques, and the race is on to build better and more powerful imaging systems so that we can further our understanding of the spatial and temporal mechanisms controlling molecular cell biology. PMID:27408708

  10. Treatment of real industrial wastewater using the combined approach of advanced oxidation followed by aerobic oxidation.

    Science.gov (United States)

    Ramteke, Lokeshkumar P; Gogate, Parag R

    2016-05-01

    Fenton oxidation and ultrasound-based pretreatment have been applied to improve the treatment of real industrial wastewater based on the use of biological oxidation. The effect of operating parameters such as Fe(2+) loading, contact time, initial pH, and hydrogen peroxide loading on the extent of chemical oxygen demand (COD) reduction and change in biochemical oxygen demand (BOD5)/COD ratio has been investigated. The optimum operating conditions established for the pretreatment were initial pH of 3.0, Fe(2+) loading of 2.0, and 2.5 g L(-1) for the US/Fenton/stirring and Fenton approach, respectively, and temperature of 25 °C with initial H2O2 loading of 1.5 g L(-1). The use of pretreatment resulted in a significant increase in the BOD5/COD ratio confirming the production of easily digestible intermediates. The effect of the type of sludge in the aerobic biodegradation was also investigated based on the use of primary activated sludge (PAS), modified activated sludge (MAS), and activated sludge (AS). Enhanced removal of the pollutants as well as higher biomass yield was observed for MAS as compared to PAS and AS. The use of US/Fenton/stirring pretreatment under the optimized conditions followed by biological oxidation using MAS resulted in maximum COD removal at 97.9 %. The required hydraulic retention time for the combined oxidation system was also significantly lower as compared to only biological oxidation operation. Kinetic studies revealed that the reduction in the COD followed a first-order kinetic model for advanced oxidation and pseudo first-order model for biodegradation. The study clearly established the utility of the combined technology for the effective treatment of real industrial wastewater. PMID:26846248

  11. Advanced Materials Growth and Processing Facility

    Data.gov (United States)

    Federal Laboratory Consortium — This most extensive of U.S. Army materials growth and processing facilities houses seven dedicated, state-of-the-art, molecular beam epitaxy and three metal organic...

  12. Advances in Nuclear Power Process Heat Applications

    International Nuclear Information System (INIS)

    Following an IAEA coordinated research project, this publication compiles the findings of research and development activities related to practical nuclear process heat applications. An overview of current progress on high temperature gas cooled reactors coupling schemes for different process heat applications, such as hydrogen production and desalination is included. The associated safety aspects are also highlighted. The summary report documents the results and conclusions of the project.

  13. Advances in the Application of Image Processing Fruit Grading

    OpenAIRE

    Fang, Chengjun; Hua, Chunjian

    2013-01-01

    In the perspective of actual production, the paper presents the advances in the application of image processing fruit grading from several aspects, such as processing precision and processing speed of image processing technology. Furthermore, the different algorithms about detecting size, shape, color and defects are combined effectively to reduce the complexity of each algorithm and achieve a balance between the processing precision and processing speed are keys to automatic apple grading.

  14. Advances of study on atmospheric methane oxidation (consumption) in forest soil

    Institute of Scientific and Technical Information of China (English)

    WANG Chen-rui; SHI Yi; YANG Xiao-ming; WU Jie; YUE Jin

    2003-01-01

    Next to CO2, methane (CH4) is the second important contributor to global warming in the atmosphere and global atmospheric CH4 budget depends on both CH4 sources and sinks. Unsaturated soil is known as a unique sink for atmospheric CH4 in terrestrial ecosystem. Many comparison studies proved that forest soil had the biggest capacity of oxidizing atmospheric CH4 in various unsaturated soils. However, up to now, there is not an overall review in the aspect of atmospheric CH4 oxidation (consumption) in forest soil. This paper analyzed advances of studies on the mechanism of atmospheric CH4 oxidation, and related natural factors (Soil physical and chemical characters, temperature and moisture, ambient main greenhouse gases concentrations, tree species, and forest fire) and anthropogenic factors (forest clear-cutting and thinning, fertilization, exogenous aluminum salts and atmospheric deposition, adding biocides, and switch of forest land use) in forest soils. It was believed that CH4 consumption rate by forest soil was limited by diffusion and sensitive to changes in water status and temperature of soil. CH4 oxidation was also particularly sensitive to soil C/N, Ambient CO2, CH4 and N2O concentrations, tree species and forest fire. In most cases, anthropogenic disturbances will decrease atmospheric CH4 oxidation, thus resulting in the elevating of atmospheric CH4. Finally, the author pointed out that our knowledge of atmospheric CH4 oxidation (consumption) in forest soil was insufficient. In order to evaluate the contribution of forest soils to atmospheric CH4 oxidation and the role of forest played in the process of global environmental change, and to forecast the trends of global warming exactly, more researchers need to studies further on CH4 oxidation in various forest soils of different areas.

  15. Leachate Treatment UsingWet Air Oxidation Processes

    Directory of Open Access Journals (Sweden)

    A Ebrahimi

    2011-04-01

    Full Text Available "nBackground and Objectives: Wet air oxidation (WAO is One of the advanced oxidation process which reduce organic matter concentration from industrial wastewater, toxic and non biodegradable substances and, solid waste leachate,etc. In this study the efficiency of wet air oxidation method in leachate treatment generating from Esfahan Composting factory was Evaluated."nMaterial and Methods: The experiment was carried out by adding 1.5 Lit of pretreated leachate sample the steel reactor with the volume of 3L. The reactor then underwent10 bar pressure at different temperature (100, 200 and 300 °C and various retention time (30, 60 and 90 min. Leachate sample in 18 stages from composting factory in Isfahan in the volume of 20 Lit was taken and the WAO method, was used for pre-treatments. Removal efficiency of COD, BOD, NH4-N, NO3 and TSS were examined."nResults: The results showed that the removal efficiency was more than 35% for COD, 38% for BOD, and 85% for TSS within one hour of reaction. The Maximum removal efficiency obtained in this study were 53.3% for NH4-N and 73.9 % forNO3-N."nConclusion: the results indicate that the reaction temperatures are the most important factors affecting degradation of organic matter. COD and BOD5 removal efficiency by WAO process increased as the time of reaction went up. In addition, BOD5/COD ratios of the effluents, which are generally regarded as an important index of biodegradability of leachate sample, were determined and improved grately as it reached to 84%. TheWAO process presented in this paper is considered an efficient process for pretreatment of leachate, as the COD, BOD5 and NO3 reduction observed in leachate samples.

  16. Anaerobic ammonium oxidation for advanced municipal wastewater treatment: is it feasible?

    Institute of Scientific and Technical Information of China (English)

    LI Jie; XIONG Bi-yong; ZHANG Shu-de; YANG Hong; ZHANG Jie

    2005-01-01

    Anaerobic ammonium oxidation(ANAMMOX) is a recently developed process to treat ammonia-rich wastewater. There were numerous articles about the new technology with focus on the ammonium-rich wastewater treatment, but few on advanced municipal wastewater treatment. The paper studied the anaerobic ammonium oxidation(ANAMMOX) process with a down flow anoxic biofilter for nitrogen removal from secondary clarifier effluent of municipal wastewater with low COD/N ratio. The results showed that ANAMMOX process is applicable to advanced wastewater treatment with normal temperature as well as ammonia-rich high temperature wastewater treatment. The results indicated that ammonia removal rate was improved by raising the nitrite concentration, and the reaction rate reached a climax at 118.4 mgN/L of the nitrite nitrogen concentration. If the concentration exceeds 118.4 mgN/L, the ANAMMOX process was significantly inhibited although the ANAMMOX bacteria still showed a relatively high reactivity. The data also indicated that the ratio of NO2- -N:NH4 + -N = 1.3:1 in the influent was appropriate for excellent nitrogen removal. The pH increased gradually along the ANAMMOX biofilter reactor. When the ANAMMOX reaction was ended, the pH was tend to calm. The data suggested that the pH could be used as an indicator to describe the course of ANAMMOX reaction.

  17. Degradation of 5-FU by means of advanced (photo)oxidation processes: UV/H2O2, UV/Fe2+/H2O2 and UV/TiO2 — Comparison of transformation products, ready biodegradability and toxicity

    International Nuclear Information System (INIS)

    The present study investigates the degradation of the antimetabolite 5-fluorouracil (5-FU) by three different advanced photo oxidation processes: UV/H2O2, UV/Fe2+/H2O2 and UV/TiO2. Prescreening experiments varying the H2O2 and TiO2 concentrations were performed in order to set the best catalyst concentrations in the UV/H2O2 and UV/TiO2 experiments, whereas the UV/Fe2+/H2O2 process was optimized varying the pH, Fe2+ and H2O2 concentrations by means of the Box–Behnken design (BBD). 5-FU was quickly removed in all the irradiation experiments. The UV/Fe2+/H2O2 and UV/TiO2 processes achieved the highest degree of mineralization, whereas the lowest one resulted from the UV/H2O2 treatment. Six transformation products were formed during the advanced (photo)oxidation processes and identified using low and high resolution mass spectrometry. Most of them were formed and further eliminated during the reactions. The parent compound of 5-FU was not biodegraded, whereas the photolytic mixture formed in the UV/H2O2 treatment after 256 min showed a noticeable improvement of the biodegradability in the closed bottle test (CBT) and was nontoxic towards Vibrio fischeri. In silico predictions showed positive alerts for mutagenic and genotoxic effects of 5-FU. In contrast, several of the transformation products (TPs) generated along the processes did not provide indications for mutagenic or genotoxic activity. One exception was TP with m/z 146 with positive alerts in several models of bacterial mutagenicity which could demand further experimental testing. Results demonstrate that advanced treatment can eliminate parent compounds and its toxicity. However, transformation products formed can still be toxic. Therefore toxicity screening after advanced treatment is recommendable. - Highlights: • Full primary elimination of 5-FU was achieved in all the treatments. • None of the processes were able to fully mineralize 5-FU. • Six transformation products (TPs) were identified during

  18. Degradation of 5-FU by means of advanced (photo)oxidation processes: UV/H{sub 2}O{sub 2}, UV/Fe{sup 2+}/H{sub 2}O{sub 2} and UV/TiO{sub 2} — Comparison of transformation products, ready biodegradability and toxicity

    Energy Technology Data Exchange (ETDEWEB)

    Lutterbeck, Carlos Alexandre, E-mail: lutterbeck@leuphana.de [Sustainable Chemistry and Material Resources, Institute of Sustainable and Environmental Chemistry, Faculty of Sustainability, Leuphana University of Lüneburg, Scharnhorststraße 1/C13, DE-21335 Lüneburg (Germany); Graduate Program in Environmental Technology, Universidade de Santa Cruz do Sul — UNISC, Av. Independência, 2293, CEP 96815-900 Santa Cruz do Sul, Rio Grande do Sul (Brazil); Wilde, Marcelo Luís, E-mail: wilde@leuphana.de [Sustainable Chemistry and Material Resources, Institute of Sustainable and Environmental Chemistry, Faculty of Sustainability, Leuphana University of Lüneburg, Scharnhorststraße 1/C13, DE-21335 Lüneburg (Germany); Baginska, Ewelina, E-mail: ewelina.baginska@leuphana.de [Sustainable Chemistry and Material Resources, Institute of Sustainable and Environmental Chemistry, Faculty of Sustainability, Leuphana University of Lüneburg, Scharnhorststraße 1/C13, DE-21335 Lüneburg (Germany); Leder, Christoph, E-mail: cleder@leuphana.de [Sustainable Chemistry and Material Resources, Institute of Sustainable and Environmental Chemistry, Faculty of Sustainability, Leuphana University of Lüneburg, Scharnhorststraße 1/C13, DE-21335 Lüneburg (Germany); Machado, Ênio Leandro, E-mail: enio@unisc.br [Graduate Program in Environmental Technology, Universidade de Santa Cruz do Sul — UNISC, Av. Independência, 2293, CEP 96815-900 Santa Cruz do Sul, Rio Grande do Sul (Brazil); and others

    2015-09-15

    The present study investigates the degradation of the antimetabolite 5-fluorouracil (5-FU) by three different advanced photo oxidation processes: UV/H{sub 2}O{sub 2}, UV/Fe{sup 2+}/H{sub 2}O{sub 2} and UV/TiO{sub 2}. Prescreening experiments varying the H{sub 2}O{sub 2} and TiO{sub 2} concentrations were performed in order to set the best catalyst concentrations in the UV/H{sub 2}O{sub 2} and UV/TiO{sub 2} experiments, whereas the UV/Fe{sup 2+}/H{sub 2}O{sub 2} process was optimized varying the pH, Fe{sup 2+} and H{sub 2}O{sub 2} concentrations by means of the Box–Behnken design (BBD). 5-FU was quickly removed in all the irradiation experiments. The UV/Fe{sup 2+}/H{sub 2}O{sub 2} and UV/TiO{sub 2} processes achieved the highest degree of mineralization, whereas the lowest one resulted from the UV/H{sub 2}O{sub 2} treatment. Six transformation products were formed during the advanced (photo)oxidation processes and identified using low and high resolution mass spectrometry. Most of them were formed and further eliminated during the reactions. The parent compound of 5-FU was not biodegraded, whereas the photolytic mixture formed in the UV/H{sub 2}O{sub 2} treatment after 256 min showed a noticeable improvement of the biodegradability in the closed bottle test (CBT) and was nontoxic towards Vibrio fischeri. In silico predictions showed positive alerts for mutagenic and genotoxic effects of 5-FU. In contrast, several of the transformation products (TPs) generated along the processes did not provide indications for mutagenic or genotoxic activity. One exception was TP with m/z 146 with positive alerts in several models of bacterial mutagenicity which could demand further experimental testing. Results demonstrate that advanced treatment can eliminate parent compounds and its toxicity. However, transformation products formed can still be toxic. Therefore toxicity screening after advanced treatment is recommendable. - Highlights: • Full primary elimination of 5-FU was

  19. Effect of vegetable oil oxidation on the hydrogenation reaction process

    OpenAIRE

    Kalantari, Faranak; Bahmaei, Manochehr; Ameri, Majid; Shoaei, Ehsan

    2010-01-01

    Hydrogenation has been carried out in a batch reactor with three different oxidized bleached oils in order to discover the effect of oxidation on the hydrogenation reaction process. Specifications of hydrogenated oils such as melting point, Iodine value, solid fat content and fatty acid composition of the oxidized oils were compared with their un-oxidized reference oils. Oxidized bleached sunflower oil was hydrogenated to target melting points (34, 39 and 42°C) at higher iodine values vs. its...

  20. Recent advances in radiation processing of food

    International Nuclear Information System (INIS)

    Commercial application of radiation technology for food processing started in the nineties after it was approved by FAO/IAEA/WHO and Codex Alimentarius Commission in the eighties. Sanitary applications were initially explored commercially with microbial decontamination of spices and dry ingredients as the primary commodities to be processed on a large scale. Subsequently, with the emergence of E.coli O157:H7 as the potential food poisoning risk in ground beef, irradiation of meat was initiated in the late nineties in the USA. Since then irradiation, has become a very useful food safety tool and the technology has been approved for addressing food safety risks in moluscan shellfish and vegetables like lettuce, spinach, and more recently for raw uncooked meat by USFDA. Phytosanitary applications assumed importance after USFDA approved irradiation as a method of phytosanitary treatment and subsequent endorsement of the process by International Plant Protection Convention (IPPC) in 2003. These approvals were responsible for development of international trade in agricultural commodities. The first to demonstrate the feasibility of the process were India and Australia, the countries that exported mangoes to New Zealand and USA, respectively. As far as the source of radiation is concerned, the world is slowly moving towards deployment of machine sources, thereby reducing its dependence on radioisotopes for commercial irradiation. (author)

  1. Advanced signal processing technology by softcomputing

    CERN Document Server

    Hsu, Charles

    2000-01-01

    This book presents worldwide outstanding research and recent progress in the applications of neural networks, fuzzy logic, chaos, independent component analysis, etc to fields related to speech recognition enhancement, supervised Fourier demixing noise elimination, acoustic databases, the human hearing system, cancer detection, image processing, and visual communications.

  2. US-UK Collaboration on Fossil Energy Advanced Materials: Task 1—Steam Oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R. [National Energy Technology Lab. (NETL), Albany, OR (United States); Tylczak, Joseph [National Energy Technology Lab. (NETL), Albany, OR (United States); Carney, Casey [National Energy Technology Lab. (NETL), Albany, OR (United States)

    2016-04-19

    This presentation goes over the following from the US-UK collaboration on Fossil Energy Advanced Materials: Task 1, Steam Oxidation: US-led or co-led deliverables, Phase II products (US), 2011-present, Phase III products, Phase III Plan, an explanation of sCO2 compared with sH2O, an explanation of Ni-base Alloys, an explanation of 300 Series (18Cr-8Ni)/E-Brite, an explanation of the typical Microchannel HX Fabrication process, and an explanation of diffusion bonded Ni-base superalloys.

  3. Overview of welding of oxide dispersion strengthened (ODS) alloys for advanced nuclear reactor applications

    International Nuclear Information System (INIS)

    Oxide dispersion strengthened (ODS) alloys are very promising materials for Generation IV reactors with a potential to be used at elevated temperatures under severe neutron exposure environment. Welding of the ODS alloys is an understudied problem. In this paper, an overview of welding of the ODS alloys useful for advanced nuclear reactor applications is presented. The microstructural changes and the resultant mechanical properties obtained by various solid state welding processes are reviewed. Based on our results on PM2000, an approach for future work on welding of the ODS alloys is suggested. (author)

  4. Recent Advancements in Semiconductor-based Optical Signal Processing

    DEFF Research Database (Denmark)

    Nielsen, M L; Mørk, Jesper

    2006-01-01

    Significant advancements in technology and basic understanding of device physics are bringing optical signal processing closer to a commercial breakthrough. In this paper we describe the main challenges in high-speed SOA-based switching.......Significant advancements in technology and basic understanding of device physics are bringing optical signal processing closer to a commercial breakthrough. In this paper we describe the main challenges in high-speed SOA-based switching....

  5. Achievements and prospects of advanced materials processed by powder technology

    OpenAIRE

    Kaysser, W.

    1993-01-01

    In this paper examples from intermetallics, composites with ductile and high strength reinforcements, nanocrystalline and superplastic materials are used to illustrate generic and special achievements and prospects of advanced materials processed by powder technology. Processing technologies include reactive powder metallurgy, nanocrystalline processing, rapid solidification and mechanical alloying.

  6. Processes regulating nitric oxide emissions from soils

    DEFF Research Database (Denmark)

    Pilegaard, Kim

    2013-01-01

    Nitric oxide (NO) is a reactive gas that plays an important role in atmospheric chemistry by influencing the production and destruction of ozone and thereby the oxidizing capacity of the atmosphere. NO also contributes by its oxidation products to the formation of acid rain. The major sources...

  7. Application of hydrogen injection and oxidation to low temperature solution-processed oxide semiconductors

    Directory of Open Access Journals (Sweden)

    Masashi Miyakawa

    2016-08-01

    Full Text Available Solution-processed oxide semiconductors are promising candidates for the low cost, large scale fabrication of oxide thin-film transistors (TFTs. In this work, a method using hydrogen injection and oxidation (HIO that allows the low temperature solution processing of oxide semiconductors was demonstrated. We found that this method significantly decreases the concentration of residual species while improving the film densification. Additionally, enhanced TFT performance was confirmed following the use of processing temperatures as low as 300 °C. The proposed process is potentially applicable to the fabrication of a wide variety of solution-processed oxide semiconductors.

  8. Improving Seismic Image with Advanced Processing Techniques

    Directory of Open Access Journals (Sweden)

    Mericy Lastra Cunill

    2012-07-01

    Full Text Available Taking Taking into account the need to improve the seismic image in the central area of Cuba, specifically in the area of the Venegas sector, located in the Cuban Folded Belt, the seismic data acquired by Cuba Petróleo (CUPET in the year 2007 was reprocessed according to the experience accumulated during the previous processing carried out in the same year, and the new geologic knowledge on the area. This was done with the objective of improving the results. The processing applied previously was analyzed by reprocessing the primary data with new focuses and procedures, among them are the following: the attenuation of the superficial wave with a filter in the Radon domain in its lineal variant, the change of the primary statics corrections of elevation by those of refraction, the study of velocity with the selection automatic biespectral of high density, the study of the anisotropy, the attenuation of the random noise, and the pre stack time and depth migration. As a result of this reprocessing, a structure that was not identified in the seismic sections of the previous processing was located at the top of a Continental Margin sediment located to the north of the sector that increased the potentialities of finding hydrocarbons in quantities of economic importance thus diminishing the risk of drilling in the sector Venegas.

  9. REMOVAL OF REMAZOL ROSSO RB DYE FROM AQUEOUS EFFLUENTS BY HOMOGENOUS FENTON OXIDATION PROCESSES

    Directory of Open Access Journals (Sweden)

    Carmen Zaharia

    2014-06-01

    Full Text Available The paper presents some data from our laboratory-setup experiments of homogenous oxidative processes with hydrogen peroxide (i.e. advanced Fenton oxidation processes applied for Remazol Rosso RB dye-containing aqueous systems, especially textile effluents. Therefore, some different operating parameters (including pH, concentration of dye, H2O2 and ferrous ions, oxidation time, temperature, stirring regime, among its were tested for determination of the best performance in effluent decoloration and dye removal, meaning the optimal values of each studied parameters for highest decoloration or dye removal.

  10. Copper Oxide Nanoparticles for Advanced Refrigerant Thermophysical Properties: Mathematical Modeling

    Directory of Open Access Journals (Sweden)

    S. A. Fadhilah

    2014-01-01

    Full Text Available In modern days, refrigeration systems are important for industrial and domestic applications. The systems consume more electricity as compared to other appliances. The refrigeration systems have been investigated thoroughly in many ways to reduce the energy consumption. Hence, nanorefrigerant which is one kind of nanofluids has been introduced as a superior properties refrigerant that increased the heat transfer rate in the refrigeration system. Many types of materials could be used as the nanoparticles to be suspended into the conventional refrigerants. In this study, the effect of the suspended copper oxide (CuO nanoparticles into the 1,1,1,2-tetrafluoroethane, R-134a is investigated by using mathematical modeling. The investigation includes the thermal conductivity, dynamic viscosity, and heat transfer rate of the nanorefrigerant in a tube of evaporator. The results show enhanced thermophysical properties of nanorefrigerant compared to the conventional refrigerant. These advanced thermophysical properties increased the heat transfer rate in the tube. The nanorefrigerant could be a potential working fluid to be used in the refrigeration system to increase the heat transfer characteristics and save the energy usage.

  11. Advanced plasma diagnostics for plasma processing

    Science.gov (United States)

    Malyshev, Mikhail Victorovich

    1999-10-01

    A new, non-intrusive, non-perturbing diagnostic method was developed that can be broadly applied to low pressure, weakly ionized plasmas and glow discharges-trace rare gases optical emission spectroscopy (TRG-OES). The method is based on a comparison of intensities of atomic emission from trace amounts of inert gases (He, Ne, Ar, Kr, and Xe) that are added to the discharge to intensities calculated from the theoretical model. The model assumes a Maxwellian electron energy distribution function (EEDF), computes the population of emitting levels both from the ground state and the metastable states of rare gases, and from the best fit between theory and experiment determines electron temperature (Te). Subject to conditions, TRG-OES can also yield electron density or its upper or lower limit. From the comparison of the emission from levels excited predominantly by high energy electrons to that excited by low energy electrons, information about the EEDF can be obtained. The use of TRG-OES also allows a traditionally qualitative actinometry technique (determination of concentration of radical species in plasma through optical emission) to become a precise quantitative method by including Te and rare gases metastables effects. A combination of TRG-OES, advanced actinometry, and Langmuir probe measurements was applied to several different plasma reactors and regimes of operation. Te measurements and experiments to correct excitation cross section were conducted in a laboratory helical resonator. Two chamber configuration of a commercial (Lam Research) metal etcher were studied to determine the effects of plasma parameters on plasma-induced damage. Two different methods (RF inductive coupling and ultra-high frequency coupling) for generating a plasma in a prototype reactor were also studied. Pulsed plasmas, a potential candidate to eliminate the plasma-induced damage to microelectronics devices that occurs in manufacturing due to differential charging of the wafer, have

  12. Avaliação do potencial de processos oxidativos avançados para remediação de águas contaminadas com geosmina e 2-MIB Evaluation of advanced oxidation processes for remediation of contamined water with geosmin and 2-MIB

    Directory of Open Access Journals (Sweden)

    Adriane Martins de Freitas

    2008-01-01

    Full Text Available In this work, the efficiency of some homogeneous advanced oxidation processes (UVC/H2O2, Fe2+/H2O2, UVC/Fe2+/H2O2, UVA/Fe2+/H2O2, solar/Fe2+/H2O2 was investigated toward the degradation of geosmin and 2-methylisoborneol (2-MIB. The effect of relevant experimental parameters (ie. pH, Fe2+ and H2O2 concentration was first investigated by factorial design, using camphor as a model substrate. In the geosmin and 2-MIB degradation studies the Fenton processes assisted by solar and UVA radiation offered the most promising results, mainly on account of high degradation capacity (higher than 80% at a reaction time of 60 min, high operational simplicity and low cost.

  13. Technology advances for Space Shuttle processing

    Science.gov (United States)

    Wiskerchen, M. J.; Mollakarimi, C. L.

    1988-01-01

    One of the major initial tasks of the Space Systems Integration and Operations Research Applications (SIORA) Program was the application of automation and robotics technology to all aspects of the Shuttle tile processing and inspection system. The SIORA Program selected a nonlinear systems engineering methodology which emphasizes a team approach for defining, developing, and evaluating new concepts and technologies for the operational system. This is achieved by utilizing rapid prototyping testbeds whereby the concepts and technologies can be iteratively tested and evaluated by the team. The present methodology has clear advantages for the design of large complex systems as well as for the upgrading and evolution of existing systems.

  14. Overview of advanced process control in welding within ERDA

    International Nuclear Information System (INIS)

    The special kinds of demands placed on ERDA weapons and reactors require them to have very reliable welds. Process control is critical in achieving this reliability. ERDA has a number of advanced process control projects underway with much of the emphasis being on electron beam welding. These include projects on voltage measurement, beam-current control, beam focusing, beam spot tracking, spike suppression, and computer control. A general discussion of process control in welding is followed by specific examples of some of the advanced joining process control projects in ERDA

  15. Homogeneous and heterogeneous aqueous phase oxidation of phenol with fenton-like processes

    OpenAIRE

    Messele, Selamawit Ashagre

    2014-01-01

    In the last decades, various chemical oxidation techniques have been developed to overcome the inconveniences associated to conventional treatment of industrial wastewaters. Advanced oxidation processes (AOPs) have been reported to be effective for the degradation of soluble organic contaminants from wastewaters containing non-biodegradable organic pollutants, because they can often provide an almost total degradation, under reasonably mild conditions of temperature and pressure. Among them, ...

  16. Thick film oxidation of copper in an electroplated MEMS process

    International Nuclear Information System (INIS)

    Copper forms a porous oxide, allowing the formation of oxide layers up to tens of microns thick to be created at modest processing temperatures. In this work, the controlled oxidation of copper is employed within an all-metal electroplating process to create electrically insulating, structural posts and beams. This capability could eliminate the additional dielectric deposition and patterning steps that are often needed during the construction of sensors, waveguides, and other microfabricated devices. In this paper, copper oxidation rates for thermal and plasma-assisted growth methods are characterized. Time control of the oxide growth enables larger copper structures to remain conductive while smaller copper posts are fully oxidized. The concept is demonstrated using the controlled oxidation of a copper layer between two nickel layers to fabricate nickel inductors having both copper electrical vias and copper oxide support pillars. Nickel was utilized in this demonstration for its resistance against low temperature oxidation and interdiffusion with copper. (paper)

  17. Study of solid oxide fuel cell interconnects, protective coatings and advanced physical vapor deposition techniques

    Science.gov (United States)

    Gannon, Paul Edward

    High energy conversion efficiency, decreased environmentally-sensitive emissions and fuel flexibility have attracted increasing attention toward solid oxide fuel cell (SOFC) systems for stationary, transportation and portable power generation. Critical durability and cost issues, however, continue to impede wide-spread deployment. Many intermediate temperature (600-800°C) planar SOFC systems employ metallic alloy interconnect components, which physically connect individual fuel cells into electric series, facilitate gas distribution to appropriate SOFC electrode chambers (fuel/anode and oxidant[air]/cathode) and provide SOFC stack mechanical support. These demanding multifunctional requirements challenge commercially-available and inexpensive metallic alloys due to corrosion and related effects. Many ongoing investigations are aimed at enabling inexpensive metallic alloys (via bulk and/or surface modifications) as SOFC interconnects (SOFC(IC)s). In this study, two advanced physical vapor deposition (PVD) techniques: large area filtered vacuum arc deposition (LAFAD), and filtered arc plasma-assisted electron beam PVD (FA-EBPVD) were used to deposit a wide-variety of protective nanocomposite (amorphous/nanocrystalline) ceramic thin-film (1,000 hours); and, dramatically reduced Cr volatility (>30-fold). Analyses and discussions of SOFC(IC) corrosion, advanced PVD processes and protective coating behavior are intended to advance understanding and accelerate the development of durable and commercially-viable SOFC systems.

  18. Advances in cost effective processing of titanium

    International Nuclear Information System (INIS)

    Recently an industry expert pointed out that one of the greatest hindrances to the growth of titanium usage has been the low percentage of material usable in the final product. Due to the extensive processing, forming, and machining operations typically performed on titanium, yield losses are high. This is especially true in aerospace applications where most titanium is used. In engine components, the start to finish ratio, known as the buy to fly ratio, is often as high as 7 to 1. This can be illustrated by looking at the use of titanium in Pratt and Whitney engines. In the JT-8D-217 used on Boeing's 737-200, the titanium buyweight is 5,385 pounds, whereas the finished titanium, flyweight is just 758 pounds. This start to finish ratio is 7.1:1, giving titanium 17.0% of total engine weight. (orig.)

  19. Advances in modeling plastic waste pyrolysis processes

    Directory of Open Access Journals (Sweden)

    Y. Safadi, J. Zeaiter

    2014-01-01

    Full Text Available The tertiary recycling of plastics via pyrolysis is recently gaining momentum due to promising economic returns from the generated products that can be used as a chemical feedstock or fuel. The need for prediction models to simulate such processes is essential in understanding in depth the mechanisms that take place during the thermal or catalytic degradation of the waste polymer. This paper presents key different models used successfully in literature so far. Three modeling schemes are identified: Power-Law, Lumped-Empirical, and Population-Balance based equations. The categorization is based mainly on the level of detail and prediction capability from each modeling scheme. The data shows that the reliability of these modeling approaches vary with the degree of details the experimental work and product analysis are trying to achieve.

  20. Optical metrology for advanced process control: full module metrology solutions

    Science.gov (United States)

    Bozdog, Cornel; Turovets, Igor

    2016-03-01

    Optical metrology is the workhorse metrology in manufacturing and key enabler to patterning process control. Recent advances in device architecture are gradually shifting the need for process control from the lithography module to other patterning processes (etch, trim, clean, LER/LWR treatments, etc..). Complex multi-patterning integration solutions, where the final pattern is the result of multiple process steps require a step-by-step holistic process control and a uniformly accurate holistic metrology solution for pattern transfer for the entire module. For effective process control, more process "knobs" are needed, and a tighter integration of metrology with process architecture.

  1. Feasibility studies: UV/chlorine advanced oxidation treatment for the removal of emerging contaminants.

    Science.gov (United States)

    Sichel, C; Garcia, C; Andre, K

    2011-12-01

    UV/chlorine (UV/HOCl and UV/ClO(2)) Advanced Oxidation Processes (AOPs) were assessed with varying process layout and compared to the state of the art UV/H(2)O(2) AOP. The process comparison focused on the economical and energy saving potential of the UV/chlorine AOP. Therefore the experiments were performed at technical scale (250 L/h continuous flow reactor) and at process energies, oxidant and model contaminant concentrations expected in full scale reference plants. As model compounds the emerging contaminants (ECs): desethylatrazine, sulfamethoxazole, carbamazepine, diclofenac, benzotriazole, tolyltriazole, iopamidole and 17α-ethinylestradiol (EE2) were degraded at initial compound concentrations of 1 μg/L in tap water and matrixes with increased organic load (46 mg/L DOC). UV/chlorine AOP organic by-product forming potential was assessed for trihalomethanes (THMs) and N-Nitrosodimethylamine (NDMA). A process design was evaluated which can considerably reduce process costs, energy consumption and by-product generation from UV/HOCl AOPs. PMID:22000058

  2. Process for producing oxidic sintered fuel pellets

    International Nuclear Information System (INIS)

    Oxidic nuclear fuel sintered compacts are produced from compacts of uranium oxide powder, from a mixture of uranium oxide powder and plutonium oxide powder or from uranium-plutonium oxide mixed crystal powder by a thermal treatment at a sintering temperature in the range of 10000C to 14000C in an oxidizing and then reducing gas atmosphere. For facilitating the setting up of concentrations of evenly distributed coarse grain in the microstructure of the nuclear fuel sintered compact, the starting powder and/or compacts are preroasted below sintering temperature by developing U4O9 crystalline phase or (U,Pu)4O9 crystalline phase and then, by preserving this crystalline phase, cooled down to the starting temperature. Proceeding from this starting temperature the compacts are heated to sintering temperature by preserving the U4O9 crystalline phase or (U,Pu)4O9 crystalline phase. (orig.)

  3. Advances in the Process Development of Biocatalytic Processes

    DEFF Research Database (Denmark)

    Tufvesson, Pär; Lima Ramos, Joana; Al-Haque, Naweed;

    2013-01-01

    Biocatalysis is already established in chemical synthesis on an industrial scale, in particular in the pharmaceutical sector. However, the wider implementation of biocatalysis is currently hindered by the extensive effort required to develop a competitive process. In order that resources spent...... on development are used in the most efficient manner for these challenging systems, a holistic view on process development and a more in-depth understanding of the underlying constraints (process related as well as biocatalyst related) are required. In this concept article a systematic approach to solve...

  4. Advanced Manufacturing Systems in Food Processing and Packaging Industry

    International Nuclear Information System (INIS)

    In this paper, several advanced manufacturing systems in food processing and packaging industry are reviewed, including: biodegradable smart packaging and Nano composites, advanced automation control system consists of fieldbus technology, distributed control system and food safety inspection features. The main purpose of current technology in food processing and packaging industry is discussed due to major concern on efficiency of the plant process, productivity, quality, as well as safety. These application were chosen because they are robust, flexible, reconfigurable, preserve the quality of the food, and efficient.

  5. Avaliação da microfiltração para remoção do lodo gerado no processo oxidativo avançado empregando o reagente de Fenton no tratamento de lixiviado de aterro sanitário Evaluation of microfiltration for removal of sludge generated in advanced oxidation process by Fenton reagent in treatment of landfill leachate

    Directory of Open Access Journals (Sweden)

    Wagner Guadagnin Moravia

    2011-12-01

    Full Text Available Uma alternativa atrativa para o tratamento de lixiviado de aterro sanitário são os processos oxidativos avançados empregando o reagente de Fenton (POA/Fenton. No entanto, a aplicação do POA/Fenton é limitada pela geração de lodo no processo. Esse lodo possui elevada concentração de ferro, o que torna necessária sua separação do efluente tratado. O objetivo desse trabalho foi avaliar a microfiltração para a remoção de lodo gerado no POA/Fenton. A pesquisa foi desenvolvida em unidade de bancada. O POA/Fenton apresentou elevada eficiência na remoção de matéria orgânica (75% e cor real (95%. O processo de microfiltração foi eficiente na separação do lodo gerado, o qual apresentou baixa sedimentabilidade, dificultando sua separação por sedimentação, além de ter contribuído para a remoção de outros poluentes.Advanced oxidation processes using Fenton's reagent (AOP/Fenton are an attractive alternative for landfill leachate treatment. However, the implementation of the AOP/Fenton is limited by the generation of sludge in the process. The sludge has a high iron concentration, which needs its separation from the treated effluent. The aim of this study was to evaluate the microfiltration for sludge removal from an AOP/Fenton. The work was conducted in bench scale. The advanced oxidation process showed high efficiency in removing organic matter (75% and true color (95%. The microfiltration was effective in separating the sludge, which showed low settling hindering their separation by sedimentation, and has contributed to the removal of other pollutants.

  6. Recent advances in processing and applications of microwave ferrites

    International Nuclear Information System (INIS)

    Next generation magnetic microwave devices will be planar, smaller, weigh less, and perform well beyond the present state-of-the-art. For this to become a reality advances in ferrite materials must first be realized. These advances include self-bias magnetization, tunability of the magnetic anisotropy, low microwave loss, and volumetric and weight reduction. To achieve these goals one must turn to novel materials processing methods. Here, we review recent advances in the processing of microwave ferrites. Attention is paid to the processing of ferrite films by pulsed laser deposition, liquid phase epitaxy, spin spray ferrite plating, screen printing, and compaction of quasi-single crystals. Conventional and novel applications of ferrite materials, including microwave non-reciprocal passive devices, microwave signal processing, negative index metamaterial-based electronics, and electromagnetic interference suppression are discussed.

  7. TECHNOLOGY SUMMARY ADVANCING TANK WASTE RETRIEVAL AND PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    SAMS TL; MENDOZA RE

    2010-08-11

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  8. TECHNOLOGY SUMMARY ADVANCING TANK WASTE RETREIVAL AND PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    SAMS TL

    2010-07-07

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  9. Removal of organic micropollutants in surface and groundwater using advanced oxidation technologies

    Energy Technology Data Exchange (ETDEWEB)

    Urkiaga, A.; Barcena, L.; Fuentes, L. de las [GAIKER Technological Centre, Parque Tecnologico, Zamudio (Bizkaia) (Spain)

    2003-07-01

    Today more than ever, there is a public concern about the importance of having water of proven quality, as urban and industrial development are highly dependent on an abundant and safe water supply. Traces of organic micropollutants have been found in natural and drinking water. Some of these water pollutants have teratogenic, mutagenic or carcinogenic effects even in minimal quantities (ppb) so actual regulations, the water framework directive 2000/60/CE and the drinking water directive (98/83/CE), have established new and more stringent standards. Emerging technologies as the advanced oxidation processes (AOPs) are expanding as very promising technologies to remove these compounds and consequently to obtain water of high quality. In this work, several compounds representing different micropollutant groups were selected: VOCs (TCE), gasoline derivatives (MTBE), pesticides and other endocrine disruptors (PCBs and Bisphenol-A). The viability of using advanced oxidation processes to eliminate these different compounds was evaluated. The efficiency of the removal has been proven, however to fulfil with the legislation limits a polishing step would be needed in most cases. Although very high removals have been obtained for the different compounds, mineralisation rates have been quite lower and intermediate compounds have been detected. Consequently, higher mineralisation rates and a more profusely study of the effects of the generated intermediates would be needed. (orig.)

  10. Recent advances of cerium oxide nanoparticles in synthesis, luminescence and biomedical studies:a review

    Institute of Scientific and Technical Information of China (English)

    何立莹; 苏玉民; 蒋兰宏; 石士考

    2015-01-01

    Nanostructured cerium oxide (CeO2) commonly known as nanoceria is a rare earth metal oxide, which plays a technologi-cally important role due to its versatile applications as automobile exhaust catalysts, oxide ion conductors in solid oxide fuel cells, electrode materials for gas sensors, ultraviolet absorbents and glass-polishing materials. However, nanoceria has little or weak lumi-nescence, and therefore its uses in high-performance luminescent devices and biomedical areas are limited. In this review, we present the recent advances of nanoceria in the aspects of synthesis, luminescence and biomedical studies. The CeO2 nanoparticles can be synthesized by solution-based methods including co-precipitation, hydrothermal, microemulsion process, sol-gel techniques, combus-tion reaction and so on. Achieving controlled morphologies and enhanced luminescence efficiency of nanoceria particles are quite es-sential for its potential energy- and environment-related applications. Additionally, a new frontier for nanoceria particles in biomedi-cal research has also been opened, which involves low toxicity, retinopathy, biosensors and cancer therapy aspects. Finally, the sum-mary and outlook on the challenges and perspectives of the nanoceria particles are proposed.

  11. Gas-phase advanced oxidation as an integrated air pollution control technique

    Directory of Open Access Journals (Sweden)

    Getachew A. Adnew

    2016-03-01

    Full Text Available Gas-phase advanced oxidation (GPAO is an emerging air cleaning technology based on the natural self-cleaning processes that occur in the Earth’s atmosphere. The technology uses ozone, UV-C lamps and water vapor to generate gas-phase hydroxyl radicals that initiate oxidation of a wide range of pollutants. In this study four types of GPAO systems are presented: a laboratory scale prototype, a shipping container prototype, a modular prototype, and commercial scale GPAO installations. The GPAO systems treat volatile organic compounds, reduced sulfur compounds, amines, ozone, nitrogen oxides, particles and odor. While the method covers a wide range of pollutants, effective treatment becomes difficult when temperature is outside the range of 0 to 80 °C, for anoxic gas streams and for pollution loads exceeding ca. 1000 ppm. Air residence time in the system and the rate of reaction of a given pollutant with hydroxyl radicals determine the removal efficiency of GPAO. For gas phase compounds and odors including VOCs (e.g. C6H6 and C3H8 and reduced sulfur compounds (e.g. H2S and CH3SH, removal efficiencies exceed 80%. The method is energy efficient relative to many established technologies and is applicable to pollutants emitted from diverse sources including food processing, foundries, water treatment, biofuel generation, and petrochemical industries.

  12. Advanced Process Technology: Combi Materials Science and Atmospheric Processing (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2011-06-01

    Capabilities fact sheet for the National Center for Photovoltaics: Process Technology and Advanced Concepts -- High-Throughput Combi Material Science and Atmospheric Processing that includes scope, core competencies and capabilities, and contact/web information.

  13. Advances in Instrumentation for Quantification of Isotopic Nitrous Oxide from ppb levels to 100%

    Science.gov (United States)

    Dong, F.; Gupta, M.; Leen, J.; Provencal, R. A.; Owano, T. G.; Baer, D. S.

    2013-12-01

    The isotopic composition of trace gases provides information of their origin and fate that cannot be determined from their concentration measurements alone. Biological source and loss processes, like bacterial production of nitrous oxide, are typically accompanied by isotopic selectivity associated with the kinetics of bond formation and destruction. Of the three important biologically mediated greenhouse gases (CO2, CH4 and N2O), the understanding of nitrous oxide isotopic budget in air lags behind the other two gases primarily due to the relatively low concentration of N2O in ambient air (~320 ppb). Furthermore, the origin of nitrates in rivers, lakes, ocean and other water supplies may be determined from analyses of isotopic nitrous oxide produced via chemical reduction or biological conversion. These processes can produce nitrous oxide at levels considerably greater than those present in ambient air. To date, analyses of isotopic nitrous oxide requires either pre-concentration of samples containing low concentrations or dilution of samples with high concentrations. We report significant advances of instrumentation for real-time measurements of site-specific isotopic nitrogen (δ15Nα, δ15Nβ, δ15N, δ18O) and mixing ratio [N2O] of nitrous oxide over a very wide range of mole fractions in air. Specifically, LGR's Isotopic N2O Analyzer can report site-specific isotopic nitrogen and isotopic oxygen continuously in flows ranging from 0.2 to over 20 ppm (parts per million) nitrous oxide in air (with preconcentration or dilution). Furthermore, for samples of limited volume, a batch technique may be used for similar isotopic measurements in discrete samples containing 0.2 ppm to 100% nitrous oxide (e.g., sample volumes from bacterial digestion can be as little as 1-10 mL). This novel technology, which employs cavity enhanced absorption spectroscopy (Off-Axis ICOS) and a mid-infrared laser (4.56 microns) and does not require any cryogenic components, has been

  14. GEOTECHNICAL/GEOCHEMICAL CHARACTERIZATION OF ADVANCED COAL PROCESS WASTE STREAMS

    Energy Technology Data Exchange (ETDEWEB)

    Edwin S. Olson; Charles J. Moretti

    1999-11-01

    Thirteen solid wastes, six coals and one unreacted sorbent produced from seven advanced coal utilization processes were characterized for task three of this project. The advanced processes from which samples were obtained included a gas-reburning sorbent injection process, a pressurized fluidized-bed coal combustion process, a coal-reburning process, a SO{sub x}, NO{sub x}, RO{sub x}, BOX process, an advanced flue desulfurization process, and an advanced coal cleaning process. The waste samples ranged from coarse materials, such as bottom ashes and spent bed materials, to fine materials such as fly ashes and cyclone ashes. Based on the results of the waste characterizations, an analysis of appropriate waste management practices for the advanced process wastes was done. The analysis indicated that using conventional waste management technology should be possible for disposal of all the advanced process wastes studied for task three. However, some wastes did possess properties that could present special problems for conventional waste management systems. Several task three wastes were self-hardening materials and one was self-heating. Self-hardening is caused by cementitious and pozzolanic reactions that occur when water is added to the waste. All of the self-hardening wastes setup slowly (in a matter of hours or days rather than minutes). Thus these wastes can still be handled with conventional management systems if care is taken not to allow them to setup in storage bins or transport vehicles. Waste self-heating is caused by the exothermic hydration of lime when the waste is mixed with conditioning water. If enough lime is present, the temperature of the waste will rise until steam is produced. It is recommended that self-heating wastes be conditioned in a controlled manner so that the heat will be safely dissipated before the material is transported to an ultimate disposal site. Waste utilization is important because an advanced process waste will not require

  15. Adding structure to the transition process to advanced mathematical activity

    Science.gov (United States)

    Engelbrecht, Johann

    2010-03-01

    The transition process to advanced mathematical thinking is experienced as traumatic by many students. Experiences that students had of school mathematics differ greatly to what is expected from them at university. Success in school mathematics meant application of different methods to get an answer. Students are not familiar with logical deductive reasoning, required in advanced mathematics. It is necessary to assist students in this transition process, in moving from general to mathematical thinking. In this article some structure is suggested for this transition period. This essay is an argumentative exposition supported by personal experience and international literature. This makes this study theoretical rather than empirical.

  16. Cost analysis of advanced turbine blade manufacturing processes

    Science.gov (United States)

    Barth, C. F.; Blake, D. E.; Stelson, T. S.

    1977-01-01

    A rigorous analysis was conducted to estimate relative manufacturing costs for high technology gas turbine blades prepared by three candidate materials process systems. The manufacturing costs for the same turbine blade configuration of directionally solidified eutectic alloy, an oxide dispersion strengthened superalloy, and a fiber reinforced superalloy were compared on a relative basis to the costs of the same blade currently in production utilizing the directional solidification process. An analytical process cost model was developed to quantitatively perform the cost comparisons. The impact of individual process yield factors on costs was also assessed as well as effects of process parameters, raw materials, labor rates and consumable items.

  17. Removal of diethyl phthalate from water solution by adsorption, photo-oxidation, ozonation and advanced oxidation process (UV/H{sub 2}O{sub 2}, O{sub 3}/H{sub 2}O{sub 2} and O{sub 3}/activated carbon)

    Energy Technology Data Exchange (ETDEWEB)

    Medellin-Castillo, Nahum A. [Centro de Investigacion y Estudios de Posgrado, Facultad de Ingenieria, Universidad Autonoma de San Luis Potosi, Av. Dr. M. Nava No.6, San Luis de Potosi, 78290 (Mexico); Ocampo-Perez, Raul [Centro de Investigacion y Estudios de Posgrado, Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, San Luis Potosi, 78290 (Mexico); Departamento de Quimica Inorganica, Facultad de Ciencias, Universidad de Granada, 18071, Granada (Spain); Leyva-Ramos, Roberto [Centro de Investigacion y Estudios de Posgrado, Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, San Luis Potosi, 78290 (Mexico); Sanchez-Polo, Manuel [Departamento de Quimica Inorganica, Facultad de Ciencias, Universidad de Granada, 18071, Granada (Spain); Rivera-Utrilla, Jose, E-mail: jrivera@ugr.es [Departamento de Quimica Inorganica, Facultad de Ciencias, Universidad de Granada, 18071, Granada (Spain); Mendez-Diaz, Jose D. [Departamento de Quimica Inorganica, Facultad de Ciencias, Universidad de Granada, 18071, Granada (Spain)

    2013-01-01

    The objective of this work was to compare the effectiveness of conventional technologies (adsorption on activated carbon, AC, and ozonation) and technologies based on advanced oxidation processes, AOPs, (UV/H{sub 2}O{sub 2}, O{sub 3}/AC, O{sub 3}/H{sub 2}O{sub 2}) to remove phthalates from aqueous solution (ultrapure water, surface water and wastewater). Diethyl phthalate (DEP) was chosen as a model pollutant because of its high water solubility (1080 mg/L at 293 K) and toxicity. The activated carbons showed a high adsorption capacity to adsorb DEP in aqueous solution (up to 858 mg/g), besides the adsorption mechanism of DEP on activated carbon is governed by dispersive interactions between {pi} electrons of its aromatic ring with {pi} electrons of the carbon graphene planes. The photodegration process showed that the pH solution does not significantly affect the degradation kinetics of DEP and the first-order kinetic model satisfactorily fitted the experimental data. It was observed that the rate of decomposition of DEP with the O{sub 3}/H{sub 2}O{sub 2} and O{sub 3}/AC systems is faster than that with only O{sub 3}. The technologies based on AOPs (UV/H{sub 2}O{sub 2}, O{sub 3}/H{sub 2}O{sub 2}, O{sub 3}/AC) significantly improve the degradation of DEP compared to conventional technologies (O{sub 3}, UV). AC adsorption, UV/H{sub 2}O{sub 2}, O{sub 3}/H{sub 2}O{sub 2}, and O{sub 3}/AC showed a high yield to remove DEP; however, the disadvantage of AC adsorption is its much longer time to reach maximum removal. The best system to treat water (ultrapure and natural) polluted with DEP is the O{sub 3}/AC one since it achieved the highest DEP degradation and TOC removal, as well as the lower water toxicity. -- Highlights: Black-Right-Pointing-Pointer Activated carbons showed a high adsorption capacity (up to 858 mg/g) to remove DEP. Black-Right-Pointing-Pointer The pH solution did not significantly affect the photodegradation kinetics of DEP. Black

  18. Advanced oxidation and adsorption modification of dust waste from standard moulding sands

    Directory of Open Access Journals (Sweden)

    A. Baliński

    2010-04-01

    Full Text Available The article discusses the process of advanced oxidation (AO with application of ultrasounds and surface modification of the dust waste collected during dry dedusting of processed moulding sands with bentonite binder. A beneficial effect of both AO and adsorption modification of dust waste, when performed with the selected type of polyelectrolyte, on the technological and mechanical properties of moulding sands prepared with an addition of this dust has been stated. In spite of the bentonite content in moulding sand reduced by 43% and replaced with modified dust waste, the mechanical properties, i.e. the compression and tensile strengths, examined on sand specimens have been improved by 10% and 13%, respectively, with no harm to other basic technological sand properties. At the same time, it was also possible to reduce by about 30% the emission rate of the main gaseous component from the BTEX group, i.e. benzene.

  19. Hybridization of natural systems with advanced treatment processes for organic micropollutant removals: New concepts in multi-barrier treatment

    KAUST Repository

    Sudhakaran, Sairam

    2013-07-01

    In the past, emphasis has been on individual treatment processes comprising conventional treatment (coagulation, sedimentation, and filtration) followed by advanced treatment processes (adsorption, ion-exchange, oxidation, and membrane separation). With the depletion of water resources and high demand for power and chemical usage, efforts need to be made to judiciously use advanced treatment processes. There is a new interest in multiple barriers with synergies in which two coupled processes can function as a hybrid process. Within the context of this paper, the hybrid processes include a natural treatment process coupled with an advanced process. Pilot/full-scale studies have shown efficient removal of OMPs by these hybrid processes. With this hybridization, the usage of resources such as power and chemicals can be reduced. In this study, coupling/hybridization of aquifer recharge and recovery (ARR) with oxidation (O3), advanced oxidation process which involves OH radicals (AOP), nanofiltration (NF), reverse osmosis (RO) and granular activated carbon (GAC) adsorption for OMP removal was studied. O3 or AOP as a pre-treatment and GAC, NF, RO, or UV/chlorination as a post-treatment to ARR was studied. NF can be replaced by RO for removal of OMPs since studies have shown similar performance of NF to RO for removal of many OMPs, thereby reducing costs and providing a more sustainable approach. © 2013 Elsevier Ltd.

  20. Hybridization of natural systems with advanced treatment processes for organic micropollutant removals: new concepts in multi-barrier treatment.

    Science.gov (United States)

    Sudhakaran, Sairam; Maeng, Sung Kyu; Amy, Gary

    2013-07-01

    Organic micropollutants (OMPs) represent a major constraint in drinking water supply. In the past, emphasis has been on individual treatment processes comprising conventional treatment (coagulation, sedimentation, and filtration) followed by advanced treatment processes (adsorption, ion-exchange, oxidation, and membrane separation). With the depletion of water resources and high demand for power and chemical usage, efforts need to be made to judiciously use advanced treatment processes. There is a new interest in multiple barriers with synergies in which two coupled processes can function as a hybrid process. Within the context of this paper, the hybrid processes include a natural treatment process coupled with an advanced process. Pilot/full-scale studies have shown efficient removal of OMPs by these hybrid processes. With this hybridization, the usage of resources such as power and chemicals can be reduced. In this study, coupling/hybridization of aquifer recharge and recovery (ARR) with oxidation (O3), advanced oxidation process which involves OH radicals (AOP), nanofiltration (NF), reverse osmosis (RO) and granular activated carbon (GAC) adsorption for OMP removal was studied. O3 or AOP as a pre-treatment and GAC, NF, RO, or UV/chlorination as a post-treatment to ARR was studied. NF can be replaced by RO for removal of OMPs since studies have shown similar performance of NF to RO for removal of many OMPs, thereby reducing costs and providing a more sustainable approach. PMID:23664475

  1. Oxidative Stress to the Cornea, Changes in Corneal Optical Properties, and Advances in Treatment of Corneal Oxidative Injuries

    OpenAIRE

    Cestmir Cejka; Jitka Cejkova

    2015-01-01

    Oxidative stress is involved in many ocular diseases and injuries. The imbalance between oxidants and antioxidants in favour of oxidants (oxidative stress) leads to the damage and may be highly involved in ocular aging processes. The anterior eye segment and mainly the cornea are directly exposed to noxae of external environment, such as air pollution, radiation, cigarette smoke, vapors or gases from household cleaning products, chemical burns from splashes of industrial chemicals, and danger...

  2. Low Temperature Processed Complementary Metal Oxide Semiconductor (CMOS) Device by Oxidation Effect from Capping Layer

    KAUST Repository

    Wang, Zhenwei

    2015-04-20

    In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190°C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field.

  3. Advanced solidification processing of an industrial gas turbine engine component

    Science.gov (United States)

    Clemens, Mei Ling; Price, Allen; Bellows, Richard S.

    2003-03-01

    This paper will describe the efforts of the Advanced Turbine Airfoil Manufacturing Technology Program sponsored by the U.S. Department of Energy through the Oak Ridge National Laboratory and Howmet Research Corporation. The purpose of the program is to develop single-crystal and directionally solidified casting technologies to benefit Advanced Turbine Systems (ATS) industrial and utility gas turbine engines. The focus is on defining and implementing advanced Vacuum Induction Melting (VIM) furnace enhancements that provide precise control of mold temperatures during solidification. Emphasis was placed on increasing the total magnitude of thermal gradients while minimizing the difference in maximum and minimum gradients produced during the solidification process. Advanced VIM casting techniques were applied to Solar Turbines Incorporated’s Titan 130 First Stage High Pressure Turbine Blade under the ATS program. A comparison of the advanced VIM casting process to the conventional Bridgeman casting process will be presented as it pertains to the thermal gradients achieved during solidification, microstructure, elemental partitioning characterization, and solution heat treat response.

  4. Evidence for roles of radicals in protein oxidation in advanced human atherosclerotic plaque

    DEFF Research Database (Denmark)

    Fu, S; Davies, Michael Jonathan; Stocker, R;

    1998-01-01

    Oxidative damage might be important in atherogenesis. Oxidized lipids are present at significant concentrations in advanced human plaque, although tissue antioxidants are mostly present at normal concentrations. Indirect evidence of protein modification (notably derivatization of lysine) or...... close similarities in relative abundances in the latter two circumstances indicate that hydroxyl radical damage might occur in plaque. The relatively higher level of dityrosine in plaque than that observed after radiolysis suggests the additional involvement of HOCl-mediated reactions in advanced plaque....

  5. Electron processing of fibre-reinforced advanced composites

    International Nuclear Information System (INIS)

    Advanced composites, such as carbon-fibre-reinforced epoxies, are used in the aircraft, aerospace, sporting goods, and transportation industries. Though thermal curing is the dominant industrial process for advanced composites, electron curing of similar composites containing acrylated epoxy matrices has been demonstrated by our work. The main attraction of electron processing technology over thermal technology is the advantages it offers which include ambient temperature curing, reduced curing times, reduced volatile emissions, better material handling, and reduced costs. Electron curing technology allows for the curing of many types of products, such as complex shaped, those containing different types of fibres and up to 15 cm thick. Our work has been done principally with the AECL's 10 MeV, 1 kW electron accelerator; we have also done some comparative work with an AECL Gammacell 220. In this paper we briefly review our work on the various aspects of electron curing of advanced composites and their properties. (Author)

  6. Amorphous mixed-metal hydroxide nanostructures for advanced water oxidation catalysts

    Science.gov (United States)

    Gao, Y. Q.; Liu, X. Y.; Yang, G. W.

    2016-02-01

    The design of highly efficient, durable, and earth-abundant catalysts for the oxygen evolution reaction (OER) is crucial in order to promote energy conversion and storage processes. Here, we synthesize amorphous mixed-metal (Ni-Fe) hydroxide nanostructures with a homogeneous distribution of Ni/Fe as well as a tunable Ni/Fe ratio by a simple, facile, green and low-cost electrochemical technique, and we demonstrate that the synthesized amorphous nanomaterials possess ultrahigh activity and super long-term cycle stability in the OER process. The amorphous Ni0.71Fe0.29(OH)x nanostructure affords a current density of 10 mA cm-2 at an overpotential of a mere 0.296 V and a small Tafel slope of 58 mV dec-1, while no deactivation is detected in the CV testing even up to 30 000 cycles, which suggests the promising application of these amorphous nanomaterials in electrochemical oxidation. Meanwhile, the distinct catalytic activities among these amorphous Ni-Fe hydroxide nanostructures prompts us to take notice of the composition of the alloy hydroxides/oxides when studying their catalytic properties, which opens an avenue for the rational design and controllable preparation of such amorphous nanomaterials as advanced OER electrocatalysts.The design of highly efficient, durable, and earth-abundant catalysts for the oxygen evolution reaction (OER) is crucial in order to promote energy conversion and storage processes. Here, we synthesize amorphous mixed-metal (Ni-Fe) hydroxide nanostructures with a homogeneous distribution of Ni/Fe as well as a tunable Ni/Fe ratio by a simple, facile, green and low-cost electrochemical technique, and we demonstrate that the synthesized amorphous nanomaterials possess ultrahigh activity and super long-term cycle stability in the OER process. The amorphous Ni0.71Fe0.29(OH)x nanostructure affords a current density of 10 mA cm-2 at an overpotential of a mere 0.296 V and a small Tafel slope of 58 mV dec-1, while no deactivation is detected in the CV

  7. Advanced materials and processes for polymer solar cell devices

    DEFF Research Database (Denmark)

    Petersen, Martin Helgesen; Søndergaard, Roar; Krebs, Frederik C

    2010-01-01

    The rapidly expanding field of polymer and organic solar cells is reviewed in the context of materials, processes and devices that significantly deviate from the standard approach which involves rigid glass substrates, indium-tin-oxide electrodes, spincoated layers of conjugated polymer...

  8. Microeconomics of advanced process window control for 50-nm gates

    Science.gov (United States)

    Monahan, Kevin M.; Chen, Xuemei; Falessi, Georges; Garvin, Craig; Hankinson, Matt; Lev, Amir; Levy, Ady; Slessor, Michael D.

    2002-07-01

    Fundamentally, advanced process control enables accelerated design-rule reduction, but simple microeconomic models that directly link the effects of advanced process control to profitability are rare or non-existent. In this work, we derive these links using a simplified model for the rate of profit generated by the semiconductor manufacturing process. We use it to explain why and how microprocessor manufacturers strive to avoid commoditization by producing only the number of dies required to satisfy the time-varying demand in each performance segment. This strategy is realized using the tactic known as speed binning, the deliberate creation of an unnatural distribution of microprocessor performance that varies according to market demand. We show that the ability of APC to achieve these economic objectives may be limited by variability in the larger manufacturing context, including measurement delays and process window variation.

  9. Recent Advances in Ultra-High-Speed Optical Signal Processing

    DEFF Research Database (Denmark)

    Mulvad, Hans Christian Hansen; Palushani, Evarist; Hu, Hao;

    2012-01-01

    We review recent advances in the optical signal processing of ultra-high-speed serial data signals up to 1.28 Tbit/s, with focus on applications of time-domain optical Fourier transformation. Experimental methods for the generation of symbol rates up to 1.28 Tbaud are also described....

  10. Advances and perspectives in catalytic oxidation of hydrocarbons in liquid phase

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    This review article summarizes recent advances in catalytic oxidation of hydrocarbons, especially presents two strategies for activation of C-H bonds or molecular oxygen. Based on our own research results, the applications of the two methods in the oxidation of cyclohexane, toluene and ethyl benzene, etc. are introduced, and the perspectives of the two methods are also discussed.

  11. Advanced Information Processing System - Fault detection and error handling

    Science.gov (United States)

    Lala, J. H.

    1985-01-01

    The Advanced Information Processing System (AIPS) is designed to provide a fault tolerant and damage tolerant data processing architecture for a broad range of aerospace vehicles, including tactical and transport aircraft, and manned and autonomous spacecraft. A proof-of-concept (POC) system is now in the detailed design and fabrication phase. This paper gives an overview of a preliminary fault detection and error handling philosophy in AIPS.

  12. Processing effects on the nutritional advancement of probiotics and prebiotics

    OpenAIRE

    Ananta, E.; Birkeland, S.-E.; Corcoran, B.; Fitzgerald, Gerald F.; Hinz, S.; Klijn, A.; Matto, J.; Mercernier, A.; Nilsson, U.; Nyman, M.; O’Sullivan, E; Parche, S; Rautonen, N.; Ross, R. Paul; Saarela, M.

    2004-01-01

    Investigates the processing effects on the nutritional advancement of probiotics and prebiotics. Efforts of health researchers to overcome difficulties that impact on the performance of functional foods; Importance of characterizing the interactions between probiotics and prebiotics in starter cultures or in functional foods prior to human consumption; Role of prebiotics on the viability and stability of probiotic cultures within food matrices during processing and storage.

  13. Ceramic component processing development for advanced gas-turbine engines

    Science.gov (United States)

    Mcentire, B. J.; Hengst, R. R.; Collins, W. T.; Taglialavore, A. P.; Yeckley, R. L.; Bright, E.; Bingham, M. G.

    1991-01-01

    A review of ceramic component advancements directed at developing manufacturing technologies for rotors, stators, vane-seat platforms and scrolls is presented. The first three components are being produced from HIPed Si3N4, while scrolls were prepared from a series of siliconized silicon-carbide materials. Developmental work has been conducted on all aspects of the fabrication process utilizing Taguchi experimental design methods. An assessment of material properties for various components from each process and material are made.

  14. Advanced multiresponse process optimisation an intelligent and integrated approach

    CERN Document Server

    Šibalija, Tatjana V

    2016-01-01

    This book presents an intelligent, integrated, problem-independent method for multiresponse process optimization. In contrast to traditional approaches, the idea of this method is to provide a unique model for the optimization of various processes, without imposition of assumptions relating to the type of process, the type and number of process parameters and responses, or interdependences among them. The presented method for experimental design of processes with multiple correlated responses is composed of three modules: an expert system that selects the experimental plan based on the orthogonal arrays; the factor effects approach, which performs processing of experimental data based on Taguchi’s quality loss function and multivariate statistical methods; and process modeling and optimization based on artificial neural networks and metaheuristic optimization algorithms. The implementation is demonstrated using four case studies relating to high-tech industries and advanced, non-conventional processes.

  15. Toxicological and chemical assessment of arsenic-contaminated groundwater after electrochemical and advanced oxidation treatments.

    Science.gov (United States)

    Radić, Sandra; Crnojević, Helena; Vujčić, Valerija; Gajski, Goran; Gerić, Marko; Cvetković, Želimira; Petra, Cvjetko; Garaj-Vrhovac, Vera; Oreščanin, Višnja

    2016-02-01

    Owing to its proven toxicity and mutagenicity, arsenic is regarded a principal pollutant in water used for drinking. The objective of this study was the toxicological and chemical evaluation of groundwater samples obtained from arsenic enriched drinking water wells before and after electrochemical and ozone-UV-H2O2-based advanced oxidation processes (EAOP). For this purpose, acute toxicity test with Daphnia magna and chronic toxicity test with Lemna minor L. were employed as well as in vitro bioassays using human peripheral blood lymphocytes (HPBLs). Several oxidative stress parameters were estimated in L.minor. Physicochemical analysis showed that EAOP treatment was highly efficient in arsenic but also in ammonia and organic compound removal from contaminated groundwater. Untreated groundwater caused only slight toxicity to HPBLs and D. magna in acute experiments. However, 7-day exposure of L. minor to raw groundwater elicited genotoxicity, a significant growth inhibition and oxidative stress injury. The observed genotoxicity and toxicity of raw groundwater samples was almost completely eliminated by EAOP treatment. Generally, the results obtained with L. minor were in agreement with those obtained in the chemical analysis suggesting the sensitivity of the model organism in monitoring of arsenic-contaminated groundwater. In parallel to chemical analysis, the implementation of chronic toxicity bioassays in a battery is recommended in the assessment of the toxic and genotoxic potential of such complex mixtures. PMID:26580737

  16. Comprehensive Study of Lanthanum Aluminate High-Dielectric-Constant Gate Oxides for Advanced CMOS Devices

    Directory of Open Access Journals (Sweden)

    Masamichi Suzuki

    2012-03-01

    Full Text Available A comprehensive study of the electrical and physical characteristics of Lanthanum Aluminate (LaAlO3 high-dielectric-constant gate oxides for advanced CMOS devices was performed. The most distinctive feature of LaAlO3 as compared with Hf-based high-k materials is the thermal stability at the interface with Si, which suppresses the formation of a low-permittivity Si oxide interfacial layer. Careful selection of the film deposition conditions has enabled successful deposition of an LaAlO3 gate dielectric film with an equivalent oxide thickness (EOT of 0.31 nm. Direct contact with Si has been revealed to cause significant tensile strain to the Si in the interface region. The high stability of the effective work function with respect to the annealing conditions has been demonstrated through comparison with Hf-based dielectrics. It has also been shown that the effective work function can be tuned over a wide range by controlling the La/(La + Al atomic ratio. In addition, gate-first n-MOSFETs with ultrathin EOT that use sulfur-implanted Schottky source/drain technology have been fabricated using a low-temperature process.

  17. AbstractApplication of Fenton-like process using iron nano oxides for pyrene removal from contaminated soils

    OpenAIRE

    S. Jorfi; Rezaee, A.; N Jaafarzadeh Haghighifard; G.A Moheb-ali

    2014-01-01

    Background and objectives: Because of problems dealing with bioremediation including being time consuming, low efficiency and toxicity to biota, application of advanced oxidation processes with higher efficiency and shorter remediation time have been considered for removal of hydrophobic hydrocarbons from contaminated soils. A great interest has been directed to Fenton oxidation because of its simplicity and high oxidation potential. The objective of this study was to determine the Fenton-lik...

  18. Oxidative processes in power plant oils

    International Nuclear Information System (INIS)

    This paper analyzes the chemical properties differences between thermal-oxidation and radioactive-oxidation in turbine oils in order to estimate the oils' Service Life. The oils were Turbine R type, provided by Repsol-YPF with only few additives such as: anti rust, antioxidant, anticorrosion and without viscosity index improvers. The oils were ISO 32 and ISO 68 grade -with viscosity index 95- and API (American Petroleum Institute) group I, due to its viscosity index (95), the percent of paraffinic component (0.03%). Different samples from the heavy water main pumps were collected with different service times and radiation fields during an Embalse NPP's outage. For comparison purposes oils from feedwater pumps systems that convey light water to the steam generators in the Turbine building -without radiation- were obtained. The properties studied by ASTM standards were: colour (visual inspection), Viscosity Index VI (ASTM D227/93), viscosity at 40 C degrees (ASTM D445/96) and Total Acid Number, TAN (ASTM D974-97). Oxidative degradation of base oils could be described by two successive mechanisms that allow the definition of two stages: Primary and Secondary Oxidation. Primary oxidation begins with the thermal generation of alkylation's reactions and acid products formation. Radiation damage operates by two mechanisms: scission and cross-linking. The first one generates free radicals of low molecular weight while the other one can build-up complex molecular networks with high or low solubility in the base oil. Moreover, radiation damage destroys additives molecules and generates colour centres different from oxidative colour modification. Due to scission and cross-linking alkyl group substitution in the aromatic rings are formed. Then, radiation acts as a precursor of Primary Oxidation. Both, thermal and radioactive, damage mechanisms can act simultaneously making the isolated analysis for each one very difficult. To manage it, a Relative Damage Index (RDI) has been

  19. Research advances in the catalysts for the selective oxidation of ethane to aldehydes

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhe; ZHAO Zhen; XU Chunming

    2005-01-01

    Selective oxidation of ethane to aldehydes is one of the most difficult processes in the catalysis researches of low alkanes. The development of selective oxidation of ethane to aldehydes (formaldehyde, acetaldehyde and acrolein) is discussed. The latest progress of the catalysts, including bulk or supported metal oxide catalysts, highly dispersed and isolated active sites catalysts, and the photo-catalytic ethane oxidation catalysts, partial oxidation of ethane in the gas phase, and the proposed reaction pathways from ethane to aldehydes are involved.

  20. Recent advances in fuel product and manufacturing process development

    International Nuclear Information System (INIS)

    This paper discusses advancements in commercial nuclear fuel products and manufacturing made by the Westinghouse Electric Corporation in response to the commercial nuclear fuel industry's demand for high reliability, increased plant availability and improved operating flexibility. The features and benefits of Westinghouse's most advanced fuel products--VANTAGE 5 for PWR plants and QUAD+ for BWR plants--are described, as well as high performance fuel concepts now under development for delivery in the late 1980s. The paper also discusses the importance of in-process quality control throughout manufacturing towards reducing product variability and improving fuel reliability

  1. Recent advances in fuel product and manufacturing process development

    International Nuclear Information System (INIS)

    This paper discusses advancements in commercial nuclear fuel products and manufacturing made by the Westinghouse Electric Corporation in response to the commercial nuclear fuel industry's demand for high reliability, increased plant availability and improved operating flexibility. The features and benefits of Westinghouse's most advanced fuel products--VANTAGE 5 for PWR plants and QUAD+ for BWR plants--are described, as well as 'high performance' fuel concepts now under development for delivery in the late 1980s. The paper also disusses the importance of in-process quality control throughout manufacturing towards reducing product variability and improving fuel reliability. (author)

  2. Advanced Oxidation Technologies/Photocatalytic Treatment of Wastewater.

    OpenAIRE

    Chen, J.

    1997-01-01

    7.1. Summary and conclusionsThe last two decennia have shown a growing interest in the photocatalytic treatment of wastewater, and more and more research has been carried out into the various aspects of photocatalysis, varying from highly fundamental aspects to practical application. However, despite all this research, there is still much to investigate. Suggested photocatalytic mechanisms, such as those for oxidation by hydroxyl radicals and for oxidation at the surface of photocatalysts, ne...

  3. INVESTIGATIONS ON SEWAGE TREATMENT PROCESS USING COMBINED BIO-OXIDIZERS

    Directory of Open Access Journals (Sweden)

    V. N. Jaromsky

    2010-01-01

    Full Text Available The paper presents results of investigations on process of aerobic waste water treatment with combined bio-oxidizers at milk processing enterprises. It has been shown that attached biocenosis, free-floating biocenosis and also bio-module rotation frequency  have exerted a significant influence on the process of an aerobic sewage treatment. It has been established that combined bio-oxidizers can be used for cleaning high concentrated waste water at the enterprises of food industry.

  4. Advanced Reactors Thermal Energy Transport for Process Industries

    Energy Technology Data Exchange (ETDEWEB)

    P. Sabharwall; S.J. Yoon; M.G. McKellar; C. Stoots; George Griffith

    2014-07-01

    The operation temperature of advanced nuclear reactors is generally higher than commercial light water reactors and thermal energy from advanced nuclear reactor can be used for various purposes such as liquid fuel production, district heating, desalination, hydrogen production, and other process heat applications, etc. Some of the major technology challenges that must be overcome before the advanced reactors could be licensed on the reactor side are qualification of next generation of nuclear fuel, materials that can withstand higher temperature, improvement in power cycle thermal efficiency by going to combined cycles, SCO2 cycles, successful demonstration of advanced compact heat exchangers in the prototypical conditions, and from the process side application the challenge is to transport the thermal energy from the reactor to the process plant with maximum efficiency (i.e., with minimum temperature drop). The main focus of this study is on doing a parametric study of efficient heat transport system, with different coolants (mainly, water, He, and molten salts) to determine maximum possible distance that can be achieved.

  5. Advanced CO2 removal process control and monitor instrumentation development

    Science.gov (United States)

    Heppner, D. B.; Dalhausen, M. J.; Klimes, R.

    1982-01-01

    A progam to evaluate, design and demonstrate major advances in control and monitor instrumentation was undertaken. A carbon dioxide removal process, one whose maturity level makes it a prime candidate for early flight demonstration was investigated. The instrumentation design incorporates features which are compatible with anticipated flight requirements. Current electronics technology and projected advances are included. In addition, the program established commonality of components for all advanced life support subsystems. It was concluded from the studies and design activities conducted under this program that the next generation of instrumentation will be greatly smaller than the prior one. Not only physical size but weight, power and heat rejection requirements were reduced in the range of 80 to 85% from the former level of research and development instrumentation. Using a microprocessor based computer, a standard computer bus structure and nonvolatile memory, improved fabrication techniques and aerospace packaging this instrumentation will greatly enhance overall reliability and total system availability.

  6. Removal of the antiviral agent oseltamivir and its biological activity by oxidative processes

    International Nuclear Information System (INIS)

    The antiviral agent oseltamivir acid (OA, the active metabolite of Tamiflu®) may occur at high concentrations in wastewater during pandemic influenza events. To eliminate OA and its antiviral activity from wastewater, ozonation and advanced oxidation processes were investigated. For circumneutral pH, kinetic measurements yielded second-order rate constants of 1.7 ± 0.1 × 105 and 4.7 ± 0.2 × 109 M−1 s−1 for the reaction of OA with ozone and hydroxyl radical, respectively. During the degradation of OA by both oxidants, the antiviral activity of the treated aqueous solutions was measured by inhibition of neuraminidase activity of two different viral strains. A transient, moderate (two-fold) increase in antiviral activity was observed in solutions treated up to a level of 50% OA transformation, while for higher degrees of transformation the activity corresponded to that caused exclusively by OA. OA was efficiently removed by ozonation in a wastewater treatment plant effluent, suggesting that ozonation can be applied to remove OA from wastewater. - Highlights: ► Oseltamivir acid (OA) is oxidized by ozone and hydroxyl radical. ► Kinetics: We determined rate constants for the reaction with these oxidants. ► The specific activity of OA as neuraminidase inhibitor disappeared during oxidation. ► Ozonation and advanced oxidation can effectively remove OA from wastewaters. - Ozone and hydroxyl radical treatment processes can degrade aqueous oseltamivir acid and remove its antiviral activity.

  7. Practical Implementations of Advanced Process Control for Linear Systems

    DEFF Research Database (Denmark)

    Knudsen, Jørgen K . H.; Huusom, Jakob Kjøbsted; Jørgensen, John Bagterp

    This paper describes some practical problems encountered, when implementing Advanced Process Control, APC, schemes on linear processes. The implemented APC controllers discussed will be LQR, Riccati MPC and Condensed MPC controllers illustrated by simulation of the Four Tank Process and a...... linearised CSTR. Advantages and disadvantages of these controllers will be discussed. All three controller types shows a set of common undesirable characteristics, which must be accounted for. At the end of the evaluation horizon the "optimal" solution has an unstable characteristics, which can be suppressed...

  8. Advances towards a Clean Hydrometallurgical Process for Chromite

    Directory of Open Access Journals (Sweden)

    Bo Zhang

    2016-01-01

    Full Text Available Because of the acute toxicity of Cr(VI-bearing substances, the pollution problem caused by chromite process residue has become a worldwide concern. In the view of relevant studies, the technologies based on the alkali treatment cannot fundamentally resolve the pollution problem, because the oxidation of Cr(III to Cr(VI is unavoidable during chromite decomposition. In contrast, the oxidation of Cr(III to Cr(VI can be controlled by the sulfuric acid treatment of chromite, and the Cr(VI pollution can be eliminated from the original source of production. Many research studies focusing on the resolutions of the key obstacles hindering the development of the sulfuric acid treatment process have been carried out, and significant progress has been achieved. In this study, a clean hydrometallurgical process without the generation of hexavalent chromium is demonstrated. First, the chromite was decomposed and leached by sulfuric acid solution in the presence of an oxidant. Then, iron was hydrothermally removed from the acid solution as the precipitate of jarosite. Finally, chromium salts were obtained by adjusting the basicity of the solution, separation and drying. With the aim of realizing industrialization, future research emphasis on the development of the sulfuric acid treatment process is proposed in this study.

  9. The Evonik-Uhde HPPO process for proplene oxide production

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, B.; Baerz, M. [Evonik Industries, Hanau (Germany); Schemel, J.; Kolbe, B. [Uhde GmbH, Dortmund/Bad Soden (Germany)

    2011-07-01

    In 2008 the HPPO technology has shown up as an economically and environmentally friendly alternative for manufacturing of propylene oxide. The HPPO technology offers the advantage of an on purpose process for manufacturing of propylene oxide without dependency on disposal or marketing of coupling products. (orig.)

  10. High temperature creep strength of Advanced Radiation Resistant Oxide Dispersion Strengthened Steels

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Sanghoon; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Austenitic stainless steel may be one of the candidates because of good strength and corrosion resistance at the high temperatures, however irradiation swelling well occurred to 120dpa at high temperatures and this leads the decrease of the mechanical properties and dimensional stability. Compared to this, ferritic/martensitic steel is a good solution because of excellent thermal conductivity and good swelling resistance. Unfortunately, the available temperature range of ferritic/martensitic steel is limited up to 650 .deg. C. ODS steel is the most promising structural material because of excellent creep and irradiation resistance by uniformly distributed nano-oxide particles with a high density which is extremely stable at the high temperature in ferritic/martensitic matrix. In this study, high temperature strength of advanced radiation resistance ODS steel was investigated for the core structural material of next generation nuclear systems. ODS martensitic steel was designed to have high homogeneity, productivity and reproducibility. Mechanical alloying, hot isostactic pressing and hot rolling processes were employed to fabricate the ODS steels, and creep rupture test as well as tensile test were examined to investigate the behavior at high temperatures. ODS steels were fabricated by a mechanical alloying and hot consolidation processes. Mechanical properties at high temperatures were investigated. The creep resistance of advanced radiation resistant ODS steels was more superior than those of ferritic/ martensitic steel, austenitic stainless steel and even a conventional ODS steel.

  11. High temperature creep strength of Advanced Radiation Resistant Oxide Dispersion Strengthened Steels

    International Nuclear Information System (INIS)

    Austenitic stainless steel may be one of the candidates because of good strength and corrosion resistance at the high temperatures, however irradiation swelling well occurred to 120dpa at high temperatures and this leads the decrease of the mechanical properties and dimensional stability. Compared to this, ferritic/martensitic steel is a good solution because of excellent thermal conductivity and good swelling resistance. Unfortunately, the available temperature range of ferritic/martensitic steel is limited up to 650 .deg. C. ODS steel is the most promising structural material because of excellent creep and irradiation resistance by uniformly distributed nano-oxide particles with a high density which is extremely stable at the high temperature in ferritic/martensitic matrix. In this study, high temperature strength of advanced radiation resistance ODS steel was investigated for the core structural material of next generation nuclear systems. ODS martensitic steel was designed to have high homogeneity, productivity and reproducibility. Mechanical alloying, hot isostactic pressing and hot rolling processes were employed to fabricate the ODS steels, and creep rupture test as well as tensile test were examined to investigate the behavior at high temperatures. ODS steels were fabricated by a mechanical alloying and hot consolidation processes. Mechanical properties at high temperatures were investigated. The creep resistance of advanced radiation resistant ODS steels was more superior than those of ferritic/ martensitic steel, austenitic stainless steel and even a conventional ODS steel

  12. Effect of longwall face advance rate on spontaneous heating process in the gob area - CFD modelling

    Energy Technology Data Exchange (ETDEWEB)

    Boleslav Taraba; Zdenek Michalec [University of Ostrava, Ostrava (Czech Republic). Dept. of Chemistry

    2011-08-15

    A commercial CFD software programme, FLUENT, was used to study the oxidation process of coal in the mined-out longwall (gob) area. A three-dimensional, single-phase model with a continuously advancing longwall face has been developed. For the model, the gob longwall area was designed on the basis of the actual longwall panel operating in the Ostrava-Karvina Coal Mines (OKD, Czech Republic). The behaviour of the coal to oxygen was modelled using the results arising mainly from the former laboratory-scale experiments with Czech bituminous coals. Basically, the technique of pulse flow calorimetry and measurements at a continuous airflow reactor were applied during the laboratory investigations. In the contribution, the main focus was to understand the effect of the longwall face advancing speed on the oxidation heat production as well as evolution of the gases in the gob area. Simultaneously, the effect of coal crushing in the mined-out area on the spontaneous heating process was examined. Numerical simulations confirmed the existence of a 'favourable' zone for the onset and development of the spontaneous heating process in the gob area. The location and the maximal temperature reached in the 'favourable' zone were found to be significantly affected by the advancing rate of the coalface. The slower the advancing rate is, the higher the maximal temperature and smaller the depth of the 'favourable' zone in the gob area are. When the rate drops to a certain 'critical' value, spontaneous heating turns to flammable combustion of the coal. The value of the 'critical' advancing rate was confirmed to increase if the grain size of the coal left in the gob decreases. Numerical examinations of carbon monoxide concentrations then proved that small incidents of spontaneous heating could occur in the gob area that need not be detected in the airflow of the longwall tail gate. 46 refs., 8 figs., 2 tabs.

  13. [Advance on oxidative stress mechanism of arsenic toxicology].

    Science.gov (United States)

    Li, Zhen; An, Yan

    2009-09-01

    Inorganic arsenic is one of proven human carcinogens, which there are so far no sound laboratory-based evidences and there are very few reports in the literature regarding arsenic carcinogenic effects in in vivo animal experiment. Because of this lack of adequate evidences, the mechanism for understanding arsenic toxicology remains vague. Recently, many modes of action for arsenic carcinogenesis have been proposed, oxidative stress is one of the stronger theories of arsenic action modes which have a substantial mass of supporting data. Further more, many researchers have pointed out that induction of oxidative stress by methylated metabolites of inorganic arsenics plays an important role in the toxicity and carcinogenicity of arsenics. The role of oxidative stress induced by arsenic in arsenic toxicology was reviewed. PMID:19877531

  14. Pretreatment of sugarcane bagasse using the advanced oxidation process by electron beam for enzymatic hydrolysis of cellulose; Pre-tratamento do bagaco de cana utilizando o processo de oxidacao avancada por feixe de eletrons para hidrolise enzimatica da celulose

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Marcia Almeida

    2013-07-01

    The sugar cane bagasse is a renewable energy source and a raw material promise in the biofuel production, once represents about 30% of glucose contained in the plant with the potential to be hydrolyzed and then converted to ethanol. The bagasse is composed of cellulose, straight chain of glucose, of hemicellulose, an amorphous polymer consisting of xylose, arabinose, galactose, and mannose, and of lignin, a complex polymer consisting of fenilpropan units that acts as waterproof coating on the fibers, which is hard to remove due its recalcitrant nature. The aim of this work was to study the electron beam processing as a pretreatment of sugarcane bagasse to enzymatic hydrolysis of cellulose. The pretreatment of sugarcane bagasse is one of the most important steps to make this material economically viable and competitive on the energy production. As a pretreatment the electron beam processing can weak the hemicellulose and lignin structures by the action highly reactive radicals that breaks the links, reducing the degree of polymerization fibers. It was evaluated the chemical and structural modifications on fibers caused by the irradiation, the enzymatic hydrolysis of electron beam as the only pretreatment and combined to steam explosion. For enzymatic hydrolysis it was used the commercial enzymes from Novozymes. The radiation processing promotes changes in structure and composition of sugarcane bagasse, increasing the solubility, that is related to hemicellulose and cellulose cleavage, and also increasing the enzymatic conversion yield. In the case of exploded bagasse there is no changes in the enzymatic hydrolysis yield, however the electron beam processing promoted a 67% reduction of furfural, that is formed in the steam explosion process. (author)

  15. Effects of Gravity on Supercritical Water Oxidation (SCWO) Processes

    Science.gov (United States)

    Hegde, Uday; Hicks, Michael

    2013-01-01

    The effects of gravity on the fluid mechanics of supercritical water jets are being studied at NASA to develop a better understanding of flow behaviors for purposes of advancing supercritical water oxidation (SCWO) technologies for applications in reduced gravity environments. These studies provide guidance for the development of future SCWO experiments in new experimental platforms that will extend the current operational range of the DECLIC (Device for the Study of Critical Liquids and Crystallization) Facility on board the International Space Station (ISS). The hydrodynamics of supercritical fluid jets is one of the basic unit processes of a SCWO reactor. These hydrodynamics are often complicated by significant changes in the thermo-physical properties that govern flow behavior (e.g., viscosity, thermal conductivity, specific heat, compressibility, etc), particularly when fluids transition from sub-critical to supercritical conditions. Experiments were conducted in a 150 ml reactor cell under constant pressure with water injections at various flow rates. Flow configurations included supercritical jets injected into either sub-critical or supercritical water. Profound gravitational influences were observed, particularly in the transition to turbulence, for the flow conditions under study. These results will be presented and the parameters of the flow that control jet behavior will be examined and discussed.

  16. Advanced ThioClear process testing. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Lani, B.

    1998-03-01

    Wet scrubbing is the leading proven commercial post-combustion FGD technology available to meet the sulfur dioxide reductions required by the Clean Air Act Amendments. To reduce costs associated with wet FGD, Dravo Lime Company has developed the ThioClear process. ThioClear is an ex-situ forced oxidation magnesium-enhanced lime FGD process. ThioClear process differs from the conventional magnesium-enhanced lime process in that the recycle liquor has minimal suspended solids and the by-products are wallboard quality gypsum and magnesium hydroxide, an excellent reagent for water treatment. The process has demonstrated sulfur dioxide removal efficiencies of +95% in both a vertical spray scrubber tower and a horizontal absorber operating at gas velocities of 16 fps, respectively. This report details the optimization studies and associated economics from testing conducted at Dravo Lime Company`s pilot plant located at the Miami Fort Station of the Cincinnati Gas and Electric Company.

  17. The muscle oxidative regulatory response to acute exercise is not impaired in less advanced COPD despite a decreased oxidative phenotype.

    Science.gov (United States)

    Slot, Ilse G M; van den Borst, Bram; Hellwig, Valéry A C V; Barreiro, Esther; Schols, Annemie M W J; Gosker, Harry R

    2014-01-01

    Already in an early disease stage, patients with chronic obstructive pulmonary disease (COPD) are confronted with impaired skeletal muscle function and physical performance due to a loss of oxidative type I muscle fibers and oxidative capacity (i.e. oxidative phenotype; Oxphen). Physical activity is a well-known stimulus of muscle Oxphen and crucial for its maintenance. We hypothesized that a blunted response of Oxphen genes to an acute bout of exercise could contribute to decreased Oxphen in COPD. For this, 28 patients with less advanced COPD (age 65 ± 7 yrs, FEV1 59 ± 16% predicted) and 15 age- and gender-matched healthy controls performed an incremental cycle ergometry test. The Oxphen response to exercise was determined by the measurement of gene expression levels of Oxphen markers in pre and 4h-post exercise quadriceps biopsies. Because exercise-induced hypoxia and oxidative stress may interfere with Oxphen response, oxygen saturation and oxidative stress markers were assessed as well. Regardless of oxygen desaturation and absolute exercise intensities, the Oxphen regulatory response to exercise was comparable between COPD patients and controls with no evidence of increased oxidative stress. In conclusion, the muscle Oxphen regulatory response to acute exercise is not blunted in less advanced COPD, regardless of exercise-induced hypoxia. Hence, this study provides further rationale for incorporation of exercise training as integrated part of disease management to prevent or slow down loss of muscle Oxphen and related functional impairment in COPD. PMID:24587251

  18. The muscle oxidative regulatory response to acute exercise is not impaired in less advanced COPD despite a decreased oxidative phenotype.

    Directory of Open Access Journals (Sweden)

    Ilse G M Slot

    Full Text Available Already in an early disease stage, patients with chronic obstructive pulmonary disease (COPD are confronted with impaired skeletal muscle function and physical performance due to a loss of oxidative type I muscle fibers and oxidative capacity (i.e. oxidative phenotype; Oxphen. Physical activity is a well-known stimulus of muscle Oxphen and crucial for its maintenance. We hypothesized that a blunted response of Oxphen genes to an acute bout of exercise could contribute to decreased Oxphen in COPD. For this, 28 patients with less advanced COPD (age 65 ± 7 yrs, FEV1 59 ± 16% predicted and 15 age- and gender-matched healthy controls performed an incremental cycle ergometry test. The Oxphen response to exercise was determined by the measurement of gene expression levels of Oxphen markers in pre and 4h-post exercise quadriceps biopsies. Because exercise-induced hypoxia and oxidative stress may interfere with Oxphen response, oxygen saturation and oxidative stress markers were assessed as well. Regardless of oxygen desaturation and absolute exercise intensities, the Oxphen regulatory response to exercise was comparable between COPD patients and controls with no evidence of increased oxidative stress. In conclusion, the muscle Oxphen regulatory response to acute exercise is not blunted in less advanced COPD, regardless of exercise-induced hypoxia. Hence, this study provides further rationale for incorporation of exercise training as integrated part of disease management to prevent or slow down loss of muscle Oxphen and related functional impairment in COPD.

  19. Advanced information processing system: Input/output network management software

    Science.gov (United States)

    Nagle, Gail; Alger, Linda; Kemp, Alexander

    1988-01-01

    The purpose of this document is to provide the software requirements and specifications for the Input/Output Network Management Services for the Advanced Information Processing System. This introduction and overview section is provided to briefly outline the overall architecture and software requirements of the AIPS system before discussing the details of the design requirements and specifications of the AIPS I/O Network Management software. A brief overview of the AIPS architecture followed by a more detailed description of the network architecture.

  20. Advanced Mathematical Model to Describe the Production of Biodiesel Process

    Directory of Open Access Journals (Sweden)

    Hikmat S. Al-Salim

    2009-12-01

    Full Text Available Advanced mathematical model was used to capture the batch reactor characteristics of reacting compounds. The model was applied to batch reactor for the production of bio-diesel from palm and kapok oils. Results of the model were compared with experimental data in terms of conversion of transesterification reaction for the production of bio-diesel under unsteady state. A good agreement was obtained between our model predictions and the experimental data. Both experimental and modeling results showed that the conversion of triglycerides to methyl ester was affected by the process conditions. The transesterification process with temperature of about 70 oC, and methanol ratio to the triglyceride of about 5 times its stoichiometry, and the NAOH catalyst of wt 0.4%, appear to be acceptable process conditions for bio diesel process production from palm oil and kapok oil. The model can be applied for endothermic batch process. © 2009 BCREC UNDIP. All rights reserved[Received: 12 August 2009, Revised: 15 October 2009; Accepted: 18 October 2009][How to Cite: A.S. Ibrehem, H. S. Al-Salim. (2009. Advanced Mathematical Model to Describe the Production of Biodiesel Process. Bulletin of Chemical Reaction Engineering and Catalysis, 4(2: 37-42. doi:10.9767/bcrec.4.2.28.37-42][How to Link/DOI: http://dx.doi.org/10.9767/bcrec.4.2.28.37-42

  1. Practical Implementations of Advanced Process Control for Linear Systems

    DEFF Research Database (Denmark)

    Knudsen, Jørgen K . H.; Huusom, Jakob Kjøbsted; Jørgensen, John Bagterp

    2013-01-01

    Most advanced process control systems are based on Model Predictive Control (MPC). In this paper we discuss three critical issues for the practical implementation of linear MPC for process control applications. The rst issue is related to oset free control and disturbance models; the second issue......-regulator structure. It enables oset free control; it can be computed eciently on-line using several optimization algorithms; and accommodates soft constraint for the outputs and for shaping the set-point tracking penalty function. We report selected observations using this implementation and discuss their practical...... models and integration of the innovation errors. If the disturbances increases, oset-free control cannot be achieved without violation of process constraints. A target calculation function is used to calculate the optimal achievable target for the process. The use of soft constraints for process output...

  2. Kinetics and mechanism of synthetic CoS oxidation process

    Directory of Open Access Journals (Sweden)

    Štrbac N.

    2006-01-01

    Full Text Available The results of investigation of kinetics and mechanism for synthetic a-CoS oxidation process are presented in this paper. Based on experimental data obtained using DTA and XRD analysis and constructed PSD diagrams for Co-S-O system, mechanism of synthetic a-CoS oxidation process is suggested. Characteristic kinetic parameters were obtained for experimental isothermal investigations of desulfurization degree using Sharp method.

  3. Kinetics and mechanism of synthetic CoS oxidation process

    OpenAIRE

    Štrbac N.; Mihajlović I.; Živković D.; Boyanov B.; Živković Ž.; Cocić M.

    2006-01-01

    The results of investigation of kinetics and mechanism for synthetic a-CoS oxidation process are presented in this paper. Based on experimental data obtained using DTA and XRD analysis and constructed PSD diagrams for Co-S-O system, mechanism of synthetic a-CoS oxidation process is suggested. Characteristic kinetic parameters were obtained for experimental isothermal investigations of desulfurization degree using Sharp method.

  4. A review on the recent developments of solution processes for oxide thin film transistors

    International Nuclear Information System (INIS)

    This review article introduces the recent advances in the development of oxide semiconductor materials based on solution processes and their potential applications. In the early stage, thin film transistors based on oxide semiconductors fabricated by solution processes used to face critical problems such as high annealing temperatures (>400 °C) required to obtain reasonable film quality, and the relatively low field effect mobility (<5 cm2 V−1 s−1) compared to devices fabricated by conventional vacuum-based techniques. In order to overcome such hurdles, the proper selection of high mobility amorphous oxide semiconductor materials is addressed first. The latter involves the combination of high mobility compounds and multilayered active stacks. Ensuing overviews are provided on the selection of optimum precursors and alternative annealing methods that enable the growth of high quality films at relatively low process temperatures (<200 °C). Reasonably high field effect mobility values (∼10 cm2 V−1 s−1) could thus be obtained by optimizing the above process parameters. Finally, potential applications of solution processed oxide semiconductor devices are summarized, involving, for instance, flexible displays, biosensors, and non-volatile memory devices. As such, further innovations in the solution process methods of oxide semiconductor devices are anticipated to allow the realization of cost effective, large area electronics in the near future. (paper)

  5. Process development status report for advanced manufacturing projects

    Energy Technology Data Exchange (ETDEWEB)

    Brinkman, J.R.; Homan, D.A.

    1990-03-30

    This is the final status report for the approved Advanced Manufacturing Projects for FY 1989. Five of the projects were begun in FY 1987, one in FY 1988, and one in FY 1989. The approved projects cover technology areas in welding, explosive material processing and evaluation, ion implantation, and automated manufacturing. It is expected that the successful completion of these projects well result in improved quality and/or reduced cost for components produced by Mound. Those projects not brought to completion will be continued under Process development in FY 1990.

  6. Novel Materials through Non-Hydrolytic Sol-Gel Processing: Negative Thermal Expansion Oxides and Beyond

    Directory of Open Access Journals (Sweden)

    Cora Lind

    2010-04-01

    Full Text Available Low temperature methods have been applied to the synthesis of many advanced materials. Non-hydrolytic sol-gel (NHSG processes offer an elegant route to stable and metastable phases at low temperatures. Excellent atomic level homogeneity gives access to polymorphs that are difficult or impossible to obtain by other methods. The NHSG approach is most commonly applied to the preparation of metal oxides, but can be easily extended to metal sulfides. Exploration of experimental variables allows control over product stoichiometry and crystal structure. This paper reviews the application of NHSG chemistry to the synthesis of negative thermal expansion oxides and selected metal sulfides.

  7. Evaluation of long-term sulfide oxidation processes within pyrrhotite-rich tailings, Lynn Lake, Manitoba.

    Science.gov (United States)

    Gunsinger, M R; Ptacek, C J; Blowes, D W; Jambor, J L

    2006-02-10

    Oxidation reactions have depleted sulfide minerals in the shallow tailings and have generated sulfate- and metal-rich pore water throughout the East Tailings Management Area (ETMA) at Lynn Lake, Manitoba, Canada. Information concerning the tailings geochemistry and mineralogy suggest the sulfide oxidation processes have reached an advanced stage in the area proximal to the point of tailings discharge. In contrast, the distal tailings, or slimes area, have a higher moisture content close to the impoundment surface, thereby impeding the ingress of oxygen and limiting sulfide oxidation. Numerical modelling of sulfide oxidation indicates the maximum rate of release for sulfate, Fe, and Ni occurred shortly after tailings deposition ceased. Although the sulfide minerals have been depleted in the very shallow tailings, the modelling suggests that sulfide oxidation will continue for hundreds and possibly thousands of years. The combination of sulfide minerals, principally pyrrhotite, that is susceptible to weathering processes and the relatively dry, coarse-grained nature of the tailings have resulted in the formation of a massive-hardpan layer in the proximal area of the ETMA. Because extensive accumulations of secondary oxyhydroxides of ferric iron are already present, remediation strategies for the ETMA should focus on mitigating the release of sulfide oxidation products rather than on preventing further oxidation. PMID:16406605

  8. Integrated Seismic Event Detection and Location by Advanced Array Processing

    Energy Technology Data Exchange (ETDEWEB)

    Kvaerna, T; Gibbons, S J; Ringdal, F; Harris, D B

    2007-02-09

    The principal objective of this two-year study is to develop and test a new advanced, automatic approach to seismic detection/location using array processing. We address a strategy to obtain significantly improved precision in the location of low-magnitude events compared with current fully-automatic approaches, combined with a low false alarm rate. We have developed and evaluated a prototype automatic system which uses as a basis regional array processing with fixed, carefully calibrated, site-specific parameters in conjuction with improved automatic phase onset time estimation. We have in parallel developed tools for Matched Field Processing for optimized detection and source-region identification of seismic signals. This narrow-band procedure aims to mitigate some of the causes of difficulty encountered using the standard array processing system, specifically complicated source-time histories of seismic events and shortcomings in the plane-wave approximation for seismic phase arrivals at regional arrays.

  9. Oil refinery wastewater treatment using physicochemical, Fenton and Photo-Fenton oxidation processes

    OpenAIRE

    Tony, Maha A.; Purcell, Patrick J.; Zhao, Y. Q.

    2012-01-01

    The objective of this study was to investigate the application of advanced oxidation processes (AOPs) to the treatment of wastewaters contaminated with hydrocarbon oil. Three different oil-contaminated wastewaters were examined and compared: (i) a ‘real’ hydrocarbon wastewater collected from an oil refinery (Conoco-Phillips Whitegate refinery, County Cork, Ireland); (ii) a ‘real’ hydrocarbon wastewater collected from a car-wash facility located at a petroleum filling station; and (iii) a ‘syn...

  10. Advances in metal-induced oxidative stress and human disease

    International Nuclear Information System (INIS)

    Detailed studies in the past two decades have shown that redox active metals like iron (Fe), copper (Cu), chromium (Cr), cobalt (Co) and other metals undergo redox cycling reactions and possess the ability to produce reactive radicals such as superoxide anion radical and nitric oxide in biological systems. Disruption of metal ion homeostasis may lead to oxidative stress, a state where increased formation of reactive oxygen species (ROS) overwhelms body antioxidant protection and subsequently induces DNA damage, lipid peroxidation, protein modification and other effects, all symptomatic for numerous diseases, involving cancer, cardiovascular disease, diabetes, atherosclerosis, neurological disorders (Alzheimer's disease, Parkinson's disease), chronic inflammation and others. The underlying mechanism of action for all these metals involves formation of the superoxide radical, hydroxyl radical (mainly via Fenton reaction) and other ROS, finally producing mutagenic and carcinogenic malondialdehyde (MDA), 4-hydroxynonenal (HNE) and other exocyclic DNA adducts. On the other hand, the redox inactive metals, such as cadmium (Cd), arsenic (As) and lead (Pb) show their toxic effects via bonding to sulphydryl groups of proteins and depletion of glutathione. Interestingly, for arsenic an alternative mechanism of action based on the formation of hydrogen peroxide under physiological conditions has been proposed. A special position among metals is occupied by the redox inert metal zinc (Zn). Zn is an essential component of numerous proteins involved in the defense against oxidative stress. It has been shown, that depletion of Zn may enhance DNA damage via impairments of DNA repair mechanisms. In addition, Zn has an impact on the immune system and possesses neuroprotective properties. The mechanism of metal-induced formation of free radicals is tightly influenced by the action of cellular antioxidants. Many low-molecular weight antioxidants (ascorbic acid (vitamin C), alpha

  11. Literature review for oxalate oxidation processes and plutonium oxalate solubility

    Energy Technology Data Exchange (ETDEWEB)

    Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-01

    A literature review of oxalate oxidation processes finds that manganese(II)-catalyzed nitric acid oxidation of oxalate in precipitate filtrate is a viable and well-documented process. The process has been operated on the large scale at Savannah River in the past, including oxidation of 20 tons of oxalic acid in F-Canyon. Research data under a variety of conditions show the process to be robust. This process is recommended for oxalate destruction in H-Canyon in the upcoming program to produce feed for the MOX facility. Prevention of plutonium oxalate precipitation in filtrate can be achieved by concentrated nitric acid/ferric nitrate sequestration of oxalate. Organic complexants do not appear practical to sequester plutonium. Testing is proposed to confirm the literature and calculation findings of this review at projected operating conditions for the upcoming campaign.

  12. A graphene superficial layer for the advanced electroforming process

    Science.gov (United States)

    Rho, Hokyun; Park, Mina; Lee, Seungmin; Bae, Sukang; Kim, Tae-Wook; Ha, Jun-Seok; Lee, Sang Hyun

    2016-06-01

    Advances in electroplating technology facilitate the progress of modern electronic devices, including computers, microprocessors and other microelectronic devices. Metal layers with high electrical and thermal conductivities are essential for high speed and high power devices. In this paper, we report an effective route to fabricate free-standing metal films using graphene as a superficial layer in the electroforming process. Chemical vapor deposition (CVD) graphene grown on a Cu foil was used as a template, which provides high electrical conductivity and low adhesive force with the template, thus enabling an effective electroforming process. The required force for delamination of the electroplated Cu layer from graphene is more than one order smaller than the force required for removing graphene from the Cu foil. We also demonstrated that the electroformed free-standing Cu thin films could be utilized for patterning microstructures and incorporated onto a flexible substrate for LEDs. This innovative process could be beneficial for the advancement of flexible electronics and optoelectronics, which require a wide range of mechanical and physical properties.Advances in electroplating technology facilitate the progress of modern electronic devices, including computers, microprocessors and other microelectronic devices. Metal layers with high electrical and thermal conductivities are essential for high speed and high power devices. In this paper, we report an effective route to fabricate free-standing metal films using graphene as a superficial layer in the electroforming process. Chemical vapor deposition (CVD) graphene grown on a Cu foil was used as a template, which provides high electrical conductivity and low adhesive force with the template, thus enabling an effective electroforming process. The required force for delamination of the electroplated Cu layer from graphene is more than one order smaller than the force required for removing graphene from the Cu foil

  13. Developing Tutorials for Advanced Physics Students: Processes and Lessons Learned

    CERN Document Server

    Baily, Charles; Pollock, Steven J

    2013-01-01

    When education researchers describe newly developed curricular materials, they typically concentrate on the research base behind their design, and the efficacy of the final products, but do not highlight the initial stages of creating the actual materials. With the aim of providing useful information for faculty engaged in similar projects, we describe here our development of a set of in-class tutorials for advanced undergraduate electrodynamics students, and discuss factors that influenced their initial design and refinement. Among the obstacles to be overcome was the investigation of student difficulties within the short time frame of our project, and devising ways for students to engage in meaningful activities on advanced-level topics within a single 50-minute class period. We argue for a process that leverages faculty experience and classroom observations, and present several guidelines for tutorial development and implementation in upper-division physics classrooms.

  14. Advanced materials and biochemical processes for geothermal applications

    Energy Technology Data Exchange (ETDEWEB)

    Kukacka, L.E.; van Rooyen, D.; Premuzic, E.T.

    1987-04-01

    Two Geothermal Technology Division (GTD)-sponsored programs: (1) Geothermal Materials Development, and (2) Advanced Biochemical Processes for Geothermal Brines, are described. In the former, work in the following tasks is in progress: (1) high temperature elastomeric materials for dynamic sealing applications, (2) advanced high temperature (300/sup 0/C) lightweight (1.1 g/cc) well cementing materials, (3) thermally conductive composites for heat exchanger tubing, (4) corrosion rates for metals in brine-contaminated binary plant working fluids, and (5) elastomeric liners for well casing. Methods for the utilization and/or the low cost environmentally acceptable disposal of toxic geothermal residues are being developed in the second program. This work is performed in two tasks. In one, microorganisms that can interact with toxic metals found in geothermal residues to convert them into soluble species for subsequent reinjection back into the reservoir or to concentrate them for removal by conventional processes are being identified. In the second task, process conditions are being defined for the encapsulation of untreated or partially biochemically treated residues in Portland cement-based formulations and the subsequent utilization of the waste fractions in building materials. Both processing methods yield materials which appear to meet disposal criteria for non-toxic solid waste, and their technical and economic feasibilities have been established.

  15. Advanced fuel cycle on the basis of pyroelectrochemical process for irradiated fuel reprocessing and vibropacking technology

    International Nuclear Information System (INIS)

    For advanced nuclear fuel cycle in SSC RIAR there is developed the pyroelectrochemical process to reprocess irradiated fuel and produce granulated oxide fuel UO2, PuO2 or (U,Pu)O2 from chloride melts. The basic technological stage is the extraction of oxides as a crystal product with the methods either of the electrolysis (UO2 and UO2-PuO2) or of the precipitating crystalIization (PuO2). After treating the granulated fuel is ready for direct use to manufacture vibropacking fuel pins. Electrochemical model for (U,Pu)O2 coprecipitation is described. There are new processes being developed: electroprecipitation of mixed oxides - (U,Np)O2, (U,Pu,Np)O2, (U,Am)O2 and (U,Pu,Am)O2. Pyroelectrochemical production of mixed actinide oxides is used both for reprocessing spent fuel and for producing actinide fuel. Both the efficiency of pyroelectrochemical methods application for reprocessing nuclear fuel and of vibropac technology for plutonium recovery are estimated. (author)

  16. High-power ultrasonic processing: Recent developments and prospective advances

    Science.gov (United States)

    Gallego-Juarez, Juan A.

    2010-01-01

    Although the application of ultrasonic energy to produce or to enhance a wide variety of processes have been explored since about the middle of the 20th century, only a reduced number of ultrasonic processes have been established at industrial level. However, during the last ten years the interest in ultrasonic processing has revived particularly in industrial sectors where the ultrasonic technology may represent a clean and efficient tool to improve classical existing processes or an innovation alternative for the development of new processes. Such seems to be the case of relevant sectors such as food industry, environment, pharmaceuticals and chemicals manufacture, machinery, mining, etc where power ultrasound is becoming an emerging technology for process development. The possible major problem in the application of high-intensity ultrasound on industrial processing is the design and development of efficient power ultrasonic systems (generators and reactors) capable of large scale successful operation specifically adapted to each individual process. In the area of ultrasonic processing in fluid media and more specifically in gases, the development of the steppedplate transducers and other power ge with extensive radiating surface has strongly contributed to the implementation at semi-industrial and industrial stage of several commercial applications, in sectors such as food and beverage industry (defoaming, drying, extraction, etc), environment (air cleaning, sludge filtration, etc...), machinery and process for manufacturing (textile washing, paint manufacture, etc). The development of different cavitational reactors for liquid treatment in continuous flow is helping to introduce into industry the wide potential of the area of sonochemistry. Processes such as water and effluent treatment, crystallization, soil remediation, etc have been already implemented at semi-industrial and/or industrial stage. Other single advances in sectors like mining or energy have

  17. Advanced Coal Conversion Process Demonstration: A DOE Assessment

    Energy Technology Data Exchange (ETDEWEB)

    National Energy Technology Laboratory

    2005-04-01

    The objective of this project was to demonstrate a process for upgrading subbituminous coal by reducing its moisture and sulfur content and increasing its heating value using the Advanced Coal Conversion Process (ACCP) unit. The ACCP unit, with a capacity of 68.3 tons of feed coal per hour (two trains of 34 tons/hr each), was located next to a unit train loading facility at WECo's Rosebud Coal Mine near Colstrip, Montana. Most of the coal processed was Rosebud Mine coal, but several other coals were also tested. The SynCoal® produced was tested both at utilities and at several industrial sites. The demonstration unit was designed to handle about one tenth of the projected throughput of a commercial facility.

  18. Development studies of a novel wet oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, T.W.; Dhooge, P.M. [Delphi Research, Inc., Albuquerque, NM (United States)

    1995-10-01

    Many DOE waste streams and remediates contain complex and variable mixtures of organic compounds, toxic metals, and radionuclides. These materials are often dispersed in organic or inorganic matrices, such as personal protective equipment, various sludges, soils, and water. Incineration and similar combustive processes do not appear to be viable options for treatment of these waste streams due to various considerations. The objective of this project is to develop a novel catalytic wet oxidation process for the treatment of multi-component wastes. The DETOX process uses a unique combination of metal catalysts to increase the rate of oxidation of organic materials.

  19. Sustaining high energy efficiency in existing processes with advanced process integration technology

    International Nuclear Information System (INIS)

    Highlights: ► Process integration with better modelling and more advanced solution methods. ► Operational changes for better environmental performance through optimisation. ► Identification of process integration technology for operational optimisation. ► Systematic implementation procedure of process integration technology. ► A case study with crude oil distillation to demonstrate the operational flexibility. -- Abstract: To reduce emissions in the process industry, much emphasis has been put on making step changes in emission reduction, by developing new process technology and making renewable energy more affordable. However, the energy saving potential of existing systems cannot be simply ignored. In recent years, there have been significant advances in process integration technology with better modelling techniques and more advanced solution methods. These methods have been applied to the new design and retrofit studies in the process industry. Here attempts are made to apply these technologies to improve the environmental performance of existing facilities with operational changes. An industrial project was carried out to demonstrate the importance and effectiveness of exploiting the operational flexibility for energy conservation. By applying advanced optimisation technique to integrate the operation of distillation and heat recovery in a crude oil distillation unit, the energy consumption was reduced by 8% without capital expenditure. It shows that with correctly identified technology and the proper execution procedure, significant energy savings and emission reduction can be achieved very quickly without major capital expenditure. This allows the industry to improve its economic and environment performance at the same time.

  20. Advanced Mathematical Model to Describe the Production of Biodiesel Process

    Directory of Open Access Journals (Sweden)

    Ahmmed S. Ibrehem

    2009-12-01

    Full Text Available Advanced mathematical model was used to capture the batch reactor characteristics of reacting compounds. The model was applied to batch reactor for the production of bio-diesel from palm and kapok oils. Results of the model were compared with experimental data in terms of conversion of transesterification reaction for the production of bio-diesel under unsteady state. A good agreement was obtained between our model predictions and the experimental data. Both experimental and modeling results showed that the conversion of triglycerides to methyl ester was affected by the process conditions. The transesterification process with temperature of about 70 oC, and methanol ratio to the triglyceride of about 5 times its stoichiometry, and the NAOH catalyst of wt 0.4%, appear to be acceptable process conditions for bio diesel process production from palm oil and kapok oil. The model can be applied for endothermic batch process. © 2009 BCREC UNDIP. All rights reserved[Received: 12 August 2009, Revised: 15 October 2009; Accepted: 18 October 2009][How to Cite: A.S. Ibrehem, H. S. Al-Salim. (2009. Advanced Mathematical Model to Describe the Production of Biodiesel Process. Bulletin of Chemical Reaction Engineering and Catalysis, 4(2: 37-42.  doi:10.9767/bcrec.4.2.7109.37-42][How to Link/DOI: http://dx.doi.org/10.9767/bcrec.4.2.7109.37-42 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/7109 ] 

  1. Measurement and modeling of advanced coal conversion processes, Volume III

    Energy Technology Data Exchange (ETDEWEB)

    Ghani, M.U.; Hobbs, M.L.; Hamblen, D.G. [and others

    1993-08-01

    A generalized one-dimensional, heterogeneous, steady-state, fixed-bed model for coal gasification and combustion is presented. The model, FBED-1, is a design and analysis tool that can be used to simulate a variety of gasification, devolatilization, and combustion processes. The model considers separate gas and solid temperatures, axially variable solid and gas flow rates, variable bed void fraction, coal drying, devolatilization based on chemical functional group composition, depolymerization, vaporization and crosslinking, oxidation, and gasification of char, and partial equilibrium in the gas phase.

  2. Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

    Energy Technology Data Exchange (ETDEWEB)

    Wood, C.; Thornton, W.; Swihart, A.; Gilman, T.

    1994-07-01

    The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories` operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment.

  3. A graphene superficial layer for the advanced electroforming process.

    Science.gov (United States)

    Rho, Hokyun; Park, Mina; Lee, Seungmin; Bae, Sukang; Kim, Tae-Wook; Ha, Jun-Seok; Lee, Sang Hyun

    2016-07-01

    Advances in electroplating technology facilitate the progress of modern electronic devices, including computers, microprocessors and other microelectronic devices. Metal layers with high electrical and thermal conductivities are essential for high speed and high power devices. In this paper, we report an effective route to fabricate free-standing metal films using graphene as a superficial layer in the electroforming process. Chemical vapor deposition (CVD) graphene grown on a Cu foil was used as a template, which provides high electrical conductivity and low adhesive force with the template, thus enabling an effective electroforming process. The required force for delamination of the electroplated Cu layer from graphene is more than one order smaller than the force required for removing graphene from the Cu foil. We also demonstrated that the electroformed free-standing Cu thin films could be utilized for patterning microstructures and incorporated onto a flexible substrate for LEDs. This innovative process could be beneficial for the advancement of flexible electronics and optoelectronics, which require a wide range of mechanical and physical properties. PMID:26949072

  4. Metrology aspects of SIMS depth profiling for advanced ULSI processes

    International Nuclear Information System (INIS)

    As the semiconductor industry roadmap passes through the 0.1 μm technology node, the junction depth of the transistor source/drain extension will be required to be less than 20 nm and the well doping will be near 1.0 μm in depth. The development of advanced ULSI processing techniques requires the evolution of new metrology tools to ensure process capability. High sensitivity (ppb) coupled with excellent depth resolution (1 nm) makes SIMS the technique of choice for measuring the in-depth chemical distribution of these dopants with high precision and accuracy. This paper will discuss the issues, which impact the accuracy and precision of SIMS measurements of ion implants (both shallow and deep). First this paper will discuss common uses of the SIMS technique in the technology development and manufacturing of advanced ULSI processes. In the second part of this paper the ability of SIMS to make high precision measurements of ion implant depth profiles will be studied

  5. Advanced Manufacturing Processes Laboratory Building 878 hazards assessment document

    International Nuclear Information System (INIS)

    The introduction of the hazards assessment process is to document the impact of the release of hazards at the Advanced Manufacturing Processes Laboratory (AMPL) that are significant enough to warrant consideration in Sandia National Laboratories' operational emergency management program. This hazards assessment is prepared in accordance with the Department of Energy Order 5500.3A requirement that facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment provides an analysis of the potential airborne release of chemicals associated with the operations and processes at the AMPL. This research and development laboratory develops advanced manufacturing technologies, practices, and unique equipment and provides the fabrication of prototype hardware to meet the needs of Sandia National Laboratories, Albuquerque, New Mexico (SNL/NM). The focus of the hazards assessment is the airborne release of materials because this requires the most rapid, coordinated emergency response on the part of the AMPL, SNL/NM, collocated facilities, and surrounding jurisdiction to protect workers, the public, and the environment

  6. H Scan/AHP advanced technology proposal evaluation process

    Energy Technology Data Exchange (ETDEWEB)

    Mack, S. [Energetics, Inc., Columbia, MD (United States); Valladares, M.R.S. de [National Renewable Energy Lab., Washington, DC (United States)

    1996-10-01

    It is anticipated that a family of high value/impact projects will be funded by the Hydrogen Program to field test hydrogen technologies that are at advanced stages of development. These projects will add substantial value to the Program in several ways, by: demonstrating successful integration of multiple advanced technologies, providing critical insight on issues of larger scale equipment design, construction and operations management, yielding cost and performance data for competitive analysis, refining and deploying enhanced safety measures. These projects will be selected through a competitive proposal evaluation process. Because of the significant scope and funding levels of projects at these development phases, Program management has indicated the need for an augmented proposal evaluation strategy to ensure that supported projects are implemented by capable investigative teams and that their successful completion will optimally advance programmatic objectives. These objectives comprise a complex set of both quantitative and qualitative factors, many of which can only be estimated using expert judgment and opinion. To meet the above need, the National Renewable Energy Laboratory (NREL) and Energetics Inc. have jointly developed a proposal evaluation methodology called H Scan/AHP. The H Scan component of the process was developed by NREL. It is a two-part survey instrument that substantially augments the type and scope of information collected in a traditional proposal package. The AHP (Analytic Hierarchy Process) component was developed by Energetics. The AHP is an established decision support methodology that allows the Program decision makers to evaluate proposals relatively based on a unique set of weighted criteria that they have determined.

  7. Oxidizing attack process of uranium ore by a carbonated liquor

    International Nuclear Information System (INIS)

    A continuous process for digesting a uraniferous ore by oxidation with a recycling aqueous liquor containing alkaline carbonates and bicarbonates in solution as well as uranium in a concentration close to its solubility limit at digestion temperature, and of recuperation of the precipitated uranium within the solid phase remaining after digestion. The digestion is carried out by spraying oxygen into the hot reactional medium in order not only to permit oxidation of the uranium and its solubilization but also to ensure that the sulphides of impurities and organic substances present in the ore are oxidized

  8. Study of the combustion process in the zinc oxide synthesis

    International Nuclear Information System (INIS)

    The study of combustion synthesis of zinc oxide was carried out. The reaction makes use of a salt containing the zinc ion (oxidizer) and a fuel. Given the exothermicity of the reaction, the process is self sustained and high temperatures are attained. This promotes the oxide formation and crystallization in a short period of time. The resulting Zn O powders show characteristics that favour applications in the field of electronic ceramics like varistors. Such characteristics, namely particle morphology and crystallinity degree, were accessed by X-ray diffraction and scanning electron microscopy, showing that combustion synthesis is a promising alternative method to produce adequate powders for varistors manufacture. (author)

  9. Process of forming catalytic surfaces for wet oxidation reactions

    Science.gov (United States)

    Jagow, R. B. (Inventor)

    1977-01-01

    A wet oxidation process was developed for oxidizing waste materials, comprising dissolved ruthenium salt in a reactant feed stream containing the waste materials. The feed stream is introduced into a reactor, and the reactor contents are then raised to an elevated temperature to effect deposition of a catalytic surface of ruthenium black on the interior walls of the reactor. The feed stream is then maintained in the reactor for a period of time sufficient to effect at least partial oxidation of the waste materials.

  10. Advances in multi-photon processes and spectroscopy, v.5

    CERN Document Server

    Lin, Sheng H

    1989-01-01

    In view of the rapid growth in both experimental and theoretical studies of multiphoton processes and multiphoton spectroscopy of atoms, ions and molecules in many interdisciplinary fields, an Advanced Series that contains review papers readable not only to active researchers in these areas but also to those who are not experts in the field but intend to enter the field is very necessary. This series attempts to serve this purpose. Each review article is written in a self-contained manner by the experts in the area so that the readers can grasp the knowledge in the area without too much prepar

  11. Advanced computational modelling for drying processes – A review

    International Nuclear Information System (INIS)

    Highlights: • Understanding the product dehydration process is a key aspect in drying technology. • Advanced modelling thereof plays an increasingly important role for developing next-generation drying technology. • Dehydration modelling should be more energy-oriented. • An integrated “nexus” modelling approach is needed to produce more energy-smart products. • Multi-objective process optimisation requires development of more complete multiphysics models. - Abstract: Drying is one of the most complex and energy-consuming chemical unit operations. R and D efforts in drying technology have skyrocketed in the past decades, as new drivers emerged in this industry next to procuring prime product quality and high throughput, namely reduction of energy consumption and carbon footprint as well as improving food safety and security. Solutions are sought in optimising existing technologies or developing new ones which increase energy and resource efficiency, use renewable energy, recuperate waste heat and reduce product loss, thus also the embodied energy therein. Novel tools are required to push such technological innovations and their subsequent implementation. Particularly computer-aided drying process engineering has a large potential to develop next-generation drying technology, including more energy-smart and environmentally-friendly products and dryers systems. This review paper deals with rapidly emerging advanced computational methods for modelling dehydration of porous materials, particularly for foods. Drying is approached as a combined multiphysics, multiscale and multiphase problem. These advanced methods include computational fluid dynamics, several multiphysics modelling methods (e.g. conjugate modelling), multiscale modelling and modelling of material properties and the associated propagation of material property variability. Apart from the current challenges for each of these, future perspectives should be directed towards material property

  12. Recent Technological Advances in Natural Language Processing and Artificial Intelligence

    OpenAIRE

    Shah, Nishal Pradeepkumar

    2012-01-01

    A recent advance in computer technology has permitted scientists to implement and test algorithms that were known from quite some time (or not) but which were computationally expensive. Two such projects are IBM's Jeopardy as a part of its DeepQA project [1] and Wolfram's Wolframalpha[2]. Both these methods implement natural language processing (another goal of AI scientists) and try to answer questions as asked by the user. Though the goal of the two projects is similar, both of them have a ...

  13. Recent advances in monolithic solid oxide fuel cell development

    International Nuclear Information System (INIS)

    The Argonne Monolithic Solid Oxide Fuel Cell (MSOFC) is fabricated in a honey comb structure having alternate corrugated and flat layers similar to corrugated paperboard. This honeycomb structure, shown schematically in this paper is lightweight yet strong. The materials used to fabricate the MSOFC include yttria-stabilized zirconia as the electrolyte, alkaline earth-doped lanthanum chromite as the interconnection material (bipolar plate), strontium-doped lanthanum manganite as the cathode or air electrode, and yttria-stabilized zirconia-nickel cermet as the anode of fuel electrode. The high power densities of the MSOFC allow it to be used in many applications that would not be possible for other fuel cell designs. Some of these applications include lightweight, mobile power supplies as well as power sources for helicopters and aircraft, automobiles, space platforms, etc. The MSOFC is particularly suited for mobile power applications because of its ability to reform hydrocarbon fuels within the fuel channels

  14. Development of an advanced bond coat for solid oxide fuel cell interconnector applications

    Science.gov (United States)

    Yeh, An-Chou; Chen, Yu-Ming; Liu, Chien-Kuo; Shong, Wei-Ja

    2015-11-01

    An advanced bond coat has been developed for solid oxide fuel cell interconnector applications; a low thermal expansion superalloy has been selected as the substrate, and the newly developed bond coat is applied between the substrate and the LSM top coat. The bond coat composition is designed to be near thermodynamic equilibrium with the substrate to minimize interdiffusion with the substrate while providing oxidation protection for the substrate. The bond coat exhibits good oxidation resistance, a low area specific resistance, and a low thermal expansion coefficient at 800 °C; experimental results indicate that interdiffusion between the bond coat and the substrate can be hindered.

  15. The Numerical Tours of Signal Processing - Advanced Computational Signal and Image Processing

    OpenAIRE

    Peyré, Gabriel

    2011-01-01

    The Numerical Tours of Signal Processing is an online collection of tutorials to learn advanced computational signal and image processing. These tours allow one to follow a step by step Matlab or Scilab implementation of many important processing algorithms. This implementation is commented and the connexions with the relevant mathematical notions are exposed. These algorithms are applied to various signal, image, movie and 3D mesh datasets. These tours are suitable for practitioners in the f...

  16. Advances in wastewater nitrogen removal by biological processes: state of the art review

    Directory of Open Access Journals (Sweden)

    Andrea G. Capodaglio

    2016-04-01

    Full Text Available The paper summarizes the state-of-the-art of the most recent advances in biological nitrogen removal, including process design criteria and technological innovations. With reference to the Modified Ludzck Ettinger (MLE process (pre-denitrification and nitrification in the activated sludge process, the most common nitrogen removal process used nowadays, a new design equation for the denitrification reactor based on specific denitrification rate (SDNR has been proposed. In addition, factors influencing SDNR (DO in the anoxic reactor; hydrodynamic behavior are analyzed, and technological solutions are proposed. Concerning technological advances, the paper presents a summary of various “deammonification” processes, better known by their patent names like ANAMMOX®, DEMON®, CANON®, ANITA® and others. These processes have already found applications in the treatment of high-strength wastewater such as digested sludge liquor and landfill leachate. Among other emerging denitrification technologies, consideration is given to the Membrane Biofilm Reactors (MBfRs that can be operated both in oxidation and reduction mode.

  17. Degradation of phenolic compounds by using advanced oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, M. [Univ. de los Andes, Escuela Basica de Ingenieria, La Hechicera, Merida (Venezuela); Hincapie, M. [Dept. de Ingenieria Sanitaria y Ambiental, Univ. de Antioquia, Medellin (Colombia); Curco, D.; Contreras, S.; Gimenez, J.; Esplugas, S. [Dept. de Ingenieria Quimica, Facultad de Quimica, Univ. de Barcelona, Barcelona (Spain)

    2003-07-01

    A new empirical kinetic equation [r = k{sub 1}c - k{sub 2} (c{sub 0} - c)] is proposed for the photocatalytic degradation of phenolic compounds. This equation considers the influence of the intermediates in the degradation of the pollutant. The correct formulation of the contaminant mass balance in the experimental device that operates in recycle mode was done. The proposed empirical kinetic equation fitted quite well with the experimental results obtained in the TiO{sub 2}-photocatalytic degradation of phenol. (orig.)

  18. Removal of malathion from various waters by advanced oxidation processes

    International Nuclear Information System (INIS)

    The degradation of malathion was investigated under various conditions, including ultrasound (US) irradiation, ultraviolet (UV) irradiation, and the combination of US/UV, UV/ZnO, UV/H/sub 2/O/sub 2/, and US/UV/ZnO/H/sub 2/O/sub 2/. In addition, the effect of the operational parameters, such as the initial concentration of the catalyst, the initial malathion concentration, the initial salt concentration (NaHCO/sub 3/ and Na/sub 2/SO/sub 4/), and pH, were studied. Analyses were performed by a gas chromatography-mass spectroscopy instrument. The k values were in the following order: US/UV/H/sub 2/O/sub 2//ZnO > US/UV > UV/ZnO> UV/H/sub 2/O/sub 2/ > UV > US. ZnO concentration of 100 mg/l, malathion initial concentration of 200 micro g/l, H/sub 2/O/sub 2/ concentration of 30 mg/l, pH of 9, and irradiation time of 105 min were the optimum conditions for degrading malathion by the US/UV/H/sub 2/O/sub 2//ZnO system. Additionally, the optimized parameters were also tested for the treatment of an actual water sample containing the pesticide. As a result, the efficiency of the US/UV/H/sub 2/O/sub 2/ZnO system was higher in the distilled water sample than in the actual water sample. (author)

  19. Safety Analysis of Soybean Processing for Advanced Life Support

    Science.gov (United States)

    Hentges, Dawn L.

    1999-01-01

    Soybeans (cv. Hoyt) is one of the crops planned for food production within the Advanced Life Support System Integration Testbed (ALSSIT), a proposed habitat simulation for long duration lunar/Mars missions. Soybeans may be processed into a variety of food products, including soymilk, tofu, and tempeh. Due to the closed environmental system and importance of crew health maintenance, food safety is a primary concern on long duration space missions. Identification of the food safety hazards and critical control points associated with the closed ALSSIT system is essential for the development of safe food processing techniques and equipment. A Hazard Analysis Critical Control Point (HACCP) model was developed to reflect proposed production and processing protocols for ALSSIT soybeans. Soybean processing was placed in the type III risk category. During the processing of ALSSIT-grown soybeans, critical control points were identified to control microbiological hazards, particularly mycotoxins, and chemical hazards from antinutrients. Critical limits were suggested at each CCP. Food safety recommendations regarding the hazards and risks associated with growing, harvesting, and processing soybeans; biomass management; and use of multifunctional equipment were made in consideration of the limitations and restraints of the closed ALSSIT.

  20. Study on process basic requirements of experimental facility of advanced spent fuel management process

    International Nuclear Information System (INIS)

    The advanced spent fuel management process, which was proposed to reduce the overall volume of the PWR spent fuel and improve safety and economy of the long-term storage of spent fuel, is under research and development. Hot cell facilities of α-γ type and inert atmosphere are required essentially for safe hot test and verification of this process. In this study, design basic data are established, and these data include process flow, process condition and yields, mass and radioactivity balance of radionuclides, process safety considerations, etc. And also, these data will be utilized for basic and detail design of hot cell facility, secured conservative safety and effective operability

  1. Evaluation, engineering and development of advanced cyclone processes

    International Nuclear Information System (INIS)

    This research and development project is one of three seeking to develop advanced, cost-effective, coal cleaning processes to help industry comply with 1990 Clean Air Act Regulations. The specific goal for this project is to develop a cycloning technology that will beneficiate coal to a level approaching 85% pyritic sulfur rejection while retaining 85% of the parent coal's heating value. A clean coal ash content of less than 6% and a moisture content, for both clean coal and reject, of less than 30% are targeted. The process under development is a physical, gravimetric-based cleaning system that removes ash bearing mineral matter and pyritic sulfur. Since a large portion of the Nation's coal reserves contain significant amounts of pyrite, physical beneficiation is viewed as a potential near-term, cost effective means of producing an environmentally acceptable fuel

  2. Advanced Signal Processing for MIMO-OFDM Receivers

    DEFF Research Database (Denmark)

    Manchón, Carles Navarro

    This thesis deals with a wide range of topics within the research area of advanced baseband receiver design for wireless communication systems. In particular, the work focuses on signal processing algorithms for receivers in multiple-input multiple-output (MIMO) orthogonal frequency......-division multiplexing (OFDM) systems, with a particular emphasis on the 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) standard as a study case. Signal processing in wireless receivers can be designed following different strategies. On the one hand, one can use intuitive argumentation to define...... the applicability of MF methods to the problem of estimation of sparse signals. Among the contributions within the area of heuristic approaches, we highlight our study of iterative MIMO detection, interference cancellation and decoding for LTE systems. A detailed study of channel estimation algorithms for OFDM...

  3. Radiation Monitoring System in Advanced Spent Fuel Conditioning Process Facility

    International Nuclear Information System (INIS)

    The Advanced spent fuel Conditioning Process is under development for effective management of spent fuel by converting UO2 into U-metal. For demonstration of this process, α-γ type new hot cell was built in the IMEF basement . To secure against radiation hazard, this facility needs radiation monitoring system which will observe the entire operating area before the hot cell and service area at back of it. This system consists of 7 parts; Area Monitor for γ-ray, Room Air Monitor for particulate and iodine in both area, Hot cell Monitor for hot cell inside high radiation and rear door interlock, Duct Monitor for particulate of outlet ventilation, Iodine Monitor for iodine of outlet duct, CCTV for watching workers and material movement, Server for management of whole monitoring system. After installation and test of this, radiation monitoring system will be expected to assist the successful ACP demonstration

  4. Advances in low-level color image processing

    CERN Document Server

    Smolka, Bogdan

    2014-01-01

    Color perception plays an important role in object recognition and scene understanding both for humans and intelligent vision systems. Recent advances in digital color imaging and computer hardware technology have led to an explosion in the use of color images in a variety of applications including medical imaging, content-based image retrieval, biometrics, watermarking, digital inpainting, remote sensing, visual quality inspection, among many others. As a result, automated processing and analysis of color images has become an active area of research, to which the large number of publications of the past two decades bears witness. The multivariate nature of color image data presents new challenges for researchers and practitioners as the numerous methods developed for single channel images are often not directly applicable to multichannel  ones. The goal of this volume is to summarize the state-of-the-art in the early stages of the color image processing pipeline.

  5. Evaluation, engineering and development of advanced cyclone processes

    Energy Technology Data Exchange (ETDEWEB)

    Durney, T.E.; Cook, A. [Coal Technology Corporation, Bristol, VA (United States); Ferris, D.D. [ICF Kaiser Engineers, Inc., Pittsburgh, PA (United States)] [and others

    1995-11-01

    This research and development project is one of three seeking to develop advanced, cost-effective, coal cleaning processes to help industry comply with 1990 Clean Air Act Regulations. The specific goal for this project is to develop a cycloning technology that will beneficiate coal to a level approaching 85% pyritic sulfur rejection while retaining 85% of the parent coal`s heating value. A clean coal ash content of less than 6% and a moisture content, for both clean coal and reject, of less than 30% are targeted. The process under development is a physical, gravimetric-based cleaning system that removes ash bearing mineral matter and pyritic sulfur. Since a large portion of the Nation`s coal reserves contain significant amounts of pyrite, physical beneficiation is viewed as a potential near-term, cost effective means of producing an environmentally acceptable fuel.

  6. Integration of Advanced Simulation and Visualization for Manufacturing Process Optimization

    Science.gov (United States)

    Zhou, Chenn; Wang, Jichao; Tang, Guangwu; Moreland, John; Fu, Dong; Wu, Bin

    2016-05-01

    The integration of simulation and visualization can provide a cost-effective tool for process optimization, design, scale-up and troubleshooting. The Center for Innovation through Visualization and Simulation (CIVS) at Purdue University Northwest has developed methodologies for such integration with applications in various manufacturing processes. The methodologies have proven to be useful for virtual design and virtual training to provide solutions addressing issues on energy, environment, productivity, safety, and quality in steel and other industries. In collaboration with its industrial partnerships, CIVS has provided solutions to companies, saving over US38 million. CIVS is currently working with the steel industry to establish an industry-led Steel Manufacturing Simulation and Visualization Consortium through the support of National Institute of Standards and Technology AMTech Planning Grant. The consortium focuses on supporting development and implementation of simulation and visualization technologies to advance steel manufacturing across the value chain.

  7. An advanced aqueous process for nuclear fuel reprocessing

    International Nuclear Information System (INIS)

    To develop an advanced aqueous reprocessing process using a minimal organic solvent and compact equipment to separate U, Pu and long-lived minor actinides from spent nuclear fuels, we have developed a new type of anion exchanger (AR-01) and several novel extraction resins containing a chelating ligand such as CMPO, Cyanex-301 and R-BTP. A hot separation experiment for a spent BWR-fuel solution was carried out by an ion exchange column packed with AR-01. To enhance the separation factor between U and FPs, electrolytic reduction of UO22+ to U+4 was studied using a flow type electrolysis cell with carbon-fiber electrode. Separation behavior of Am(III) from simulated HLW by CMPO and R-BTP impregnated resins were investigated. On the basis of the experimental results, an advanced aqueous process which consists of anion exchange as main separation method, electrolytic reduction for reducing U(VI) to U(IV) and extraction chromatography for MA partitioning has been designed and evaluated preliminarily. (author)

  8. Differential oxidative status and immune characterization of the early and advanced stages of human breast cancer.

    Science.gov (United States)

    Panis, C; Victorino, V J; Herrera, A C S A; Freitas, L F; De Rossi, T; Campos, F C; Simão, A N Colado; Barbosa, D S; Pinge-Filho, P; Cecchini, R; Cecchini, A L

    2012-06-01

    Breast cancer is the malignant neoplasia with the highest incidence in women worldwide. Chronic oxidative stress and inflammation have been indicated as major mediators during carcinogenesis and cancer progression. Human studies have not considered the complexity of tumor biology during the stages of cancer advance, limiting their clinical application. The purpose of this study was to characterize systemic oxidative stress and immune response parameters in early (ED; TNM I and II) and advanced disease (AD; TNM III and IV) of patients diagnosed with infiltrative ductal carcinoma breast cancer. Oxidative stress parameters were evaluated by plasmatic lipoperoxidation, carbonyl content, thiobarbituric reactive substances (TBARS), nitric oxide levels (NO), total radical antioxidant parameter (TRAP), superoxide dismutase, and catalase activities and GSH levels. Immune evaluation was determined by TNF-α, IL-1β, IL-12, and IL-10 levels and leukocytes oxidative burst evaluation by chemiluminescence. Tissue damage analysis included heart (total CK and CKMB), liver (AST, ALT, GGT), and renal (creatinine, urea, and uric acid) plasmatic markers. C-reactive protein (CRP) and iron metabolism were also evaluated. Analysis of the results verified different oxidative stress statuses occur at distinct cancer stages. ED was characterized by reduction in catalase, 8-isoprostanes, and GSH levels, with enhanced lipid peroxidation and TBARS levels. AD exhibited more pronounced oxidative status, with reduction in catalase activity and TRAP, intense lipid peroxidation and high levels of NO, TBARs, and carbonyl content. ED patients presented a Th2 immune pattern, while AD exhibited Th1 status. CRP levels and ferritin were increased in both stages of disease. Leukocytes burst impairment was observed in both the groups. Plasma iron levels were significantly elevated in AD. The data obtained indicated that oxidative stress enhancement and immune response impairment may be necessary to ensure

  9. Thermal conductivities of minor actinide oxides for advanced fuel

    International Nuclear Information System (INIS)

    The thermal diffusivities of americium oxide and neptunium dioxide were determined by a laser flash method. It was found that the thermal diffusivities of AmO2-x and NpO2 decreased with increasing temperature. It was also found that the decrease in O/Am ratio during the thermal diffusivity measurements under vacuum resulted in a slight decrease in thermal diffusivity of AmO2-x. The thermal conductivities of AmO2-x and NpO2 were evaluated from the measured thermal diffusivities, heat capacities and bulk densities. The thermal conductivity of AmO2-x was smaller than those of the literature values of UO2 and PuO2. On the other hand, the thermal conductivity of NpO2 from 873 to 1473 K lay between those of UO2 and PuO2. The thermal conductivities of AmO2-x and NpO2 decreased with increasing temperature in the temperature range investigated. This temperature dependence of thermal conductivities showed a similar tendency as those of UO2, PuO2 and (U0.8Pu0.2)O2-x. (authors)

  10. Preparation of oxide powder by continuous oxidation process from recycled Fe-77Ni alloy scrap

    Science.gov (United States)

    Yun, J. Y.; Park, D. H.; Jung, G. J.; Wang, J. P.

    2015-12-01

    The oxidation behavior of Fe-77Ni alloy scrap was studied under a 0.2 atm oxygen partial pressure at the temperature range of 400°C to 900°C. The oxidation rate was found to be increased with an increase of temperature and followed the parabolic rate law with linearly proportional to temperature. Microstructure and cross-sectional area of the oxide layer were examined by SEM, EDX, and XRD. It could be speculated that rate-limiting step was controlled by diffusion through either the spinel structure or the NiO layer, both of which were present in this alloy during oxidation at elevated temperatures. In the long run, oxide powder less than 10 μm from Fe-77Ni alloy scrap was obtained using ball-milling and sieving processes and recovery ratio approached up to 97% for 15 hours.

  11. Near-field performance of the advanced cold process canister

    International Nuclear Information System (INIS)

    A near-field performance evaluation of an advanced cold process canister for spent fuel disposal has been performed jointly by TVO, Finland and SKB, Sweden. The canister consists of a steel canister as a load bearing element, with an outer corrosion shield of copper. In the analysis, as well internal (ie corrosion processes from the inside of the canister) as external processes (mechanical and chemical) have been considered both prior to and after canister breach. The major conclusions for the evaluation are: Internal processes cannot cause the canister breach under foreseen conditions, ie local-iced corrosion for the steel or copper canisters can be dismissed as a failure mechanism; The evaluation of the effects of processed outside the canister indicate that there is no rapid mechanism to endanger the integrity of the canister. Consequently the service life of the canister will be several million years. For completeness also evaluation of post-failure behaviour was carried out. Analyses were focussed on low probability phenomena from faults in canisters. Some items were identified where further research is justified in order to increase knowledge of the phenomena and thus strengthen the confidence of safety margins. However, it can be concluded that the risks of these scenarios can be judged to be acceptable. This is due to the fact that firstly, the probability of occurrence of most of these scenarios can be controlled to a large extent through technical measures. Secondly, these analyses indicated that the consequences would not be severe

  12. Technology Summary Advancing Tank Waste Retreival And Processing

    International Nuclear Information System (INIS)

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them. Hanford's underground waste storage tanks hold approximately 57 million gallons of radiochemical waste from nuclear defense production - more tank waste than any other site in the United States. In addition, the waste is uniquely complicated since it contains constituents from at least six major radiochemical processes and several lesser processes. It is intermixed and complexed more than any other waste collection known to exist in the world. The multi-faceted nature of Hanford's tank waste means that legally binding agreements in the Federal Facility Agreement and Consent Order (known as the Tri-Party Agreement) and between the Department of Energy (DOE) and its contractors may not be met using current vitrification schedules, plans and methods. WRPS and the DOE are therefore developing, testing, and deploying technologies to ensure that they can meet the necessary commitments and complete the DOE's River Protection Project (RPP) mission within environmentally acceptable requirements. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  13. Near-field performance of the advanced cold process canister

    International Nuclear Information System (INIS)

    A near-field performance evaluation of an Advanced Cold Process Canister for spent fuel disposal has been performed jointly by TVO, Finland and SKB, Sweden. The canister consists of a steel canister as a load bearing element, with an outer corrosion shield of copper. The canister design was originally proposed by TVO. In the analysis, as well internal (ie corrosion processes from the inside of the canister) as external processes (mechanical and chemical) have been considered both prior to and after canister breach. Throughout the analysis, present day underground conditions has been assumed to persist during the service life of the canister. The major conclusions for the evaluation are: Internal processes cannot cause the canister breach under foreseen conditions, ie localized corrosion for the steel or copper canisters can be dismissed as a failure mechanism. The evaluation of the effects of processes outside the canister indicate that there is no rapid mechanism to endanger the integrity of the canister. Consequently the service life of the canister will be several million years. This factor will ensure the safety of the concept. (orig.)

  14. LITERATURE REVIEW FOR OXALATE OXIDATION PROCESSES AND PLUTONIUM OXALATE SOLUBILITY

    Energy Technology Data Exchange (ETDEWEB)

    Nash, C.

    2012-02-03

    A literature review of oxalate oxidation processes finds that manganese(II)-catalyzed nitric acid oxidation of oxalate in precipitate filtrate is a viable and well-documented process. The process has been operated on the large scale at Savannah River in the past, including oxidation of 20 tons of oxalic acid in F-Canyon. Research data under a variety of conditions show the process to be robust. This process is recommended for oxalate destruction in H-Canyon in the upcoming program to produce feed for the MOX facility. Prevention of plutonium oxalate precipitation in filtrate can be achieved by concentrated nitric acid/ferric nitrate sequestration of oxalate. Organic complexants do not appear practical to sequester plutonium. Testing is proposed to confirm the literature and calculation findings of this review at projected operating conditions for the upcoming campaign. H Canyon plans to commence conversion of plutonium metal to low-fired plutonium oxide in 2012 for eventual use in the Mixed Oxide Fuel (MOX) Facility. The flowsheet includes sequential operations of metal dissolution, ion exchange, elution, oxalate precipitation, filtration, and calcination. All processes beyond dissolution will occur in HB-Line. The filtration step produces an aqueous filtrate that may have as much as 4 M nitric acid and 0.15 M oxalate. The oxalate needs to be removed from the stream to prevent possible downstream precipitation of residual plutonium when the solution is processed in H Canyon. In addition, sending the oxalate to the waste tank farm is undesirable. This report addresses the processing options for destroying the oxalate in existing H Canyon equipment.

  15. RECENT ADVANCES IN THE DEVELOPMENT OF THE HYBRID SULFUR PROCESS FOR HYDROGEN PRODUCTION

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D.

    2010-07-22

    Thermochemical processes are being developed to provide global-scale quantities of hydrogen. A variant on sulfur-based thermochemical cycles is the Hybrid Sulfur (HyS) Process, which uses a sulfur dioxide depolarized electrolyzer (SDE) to produce the hydrogen. In the HyS Process, sulfur dioxide is oxidized in the presence of water at the electrolyzer anode to produce sulfuric acid and protons. The protons are transported through a cation-exchange membrane electrolyte to the cathode and are reduced to form hydrogen. In the second stage of the process, the sulfuric acid by-product from the electrolyzer is thermally decomposed at high temperature to produce sulfur dioxide and oxygen. The two gases are separated and the sulfur dioxide recycled to the electrolyzer for oxidation. The Savannah River National Laboratory (SRNL) has been exploring a fuel-cell design concept for the SDE using an anolyte feed comprised of concentrated sulfuric acid saturated with sulfur dioxide. The advantages of this design concept include high electrochemical efficiency and small footprint compared to a parallel-plate electrolyzer design. This paper will provide a summary of recent advances in the development of the SDE for the HyS process.

  16. OXIDATIVE STRESS AND VASCULAR DAMAGE IN HYPOXIA PROCESSES. MALONDIALDEHYDE (MDA AS BIOMARKER FOR OXIDATIVE DAMAGE

    Directory of Open Access Journals (Sweden)

    Muñiz P

    2014-05-01

    Full Text Available Changes in the levels oxidative stress biomarkers are related with different diseases such as ischemia/reperfusion, cardiovascular, renal, aging, etc. One of these biomarkers is the malondialdehyde (MDA generated as resulted of the process of lipid peroxidation. This biomarker is increased under conditions of the oxidative stress. Their levels, have been frequently used to measure plasma oxidative damage to lipids by their atherogenic potential. Its half-life high and their reactivity allows it to act both inside and outside of cells and interaction with proteins and DNA involve their role in different pathophysiological processes. This paper presents an analysis of the use of MDA as a biomarker of oxidative stress and its implications associated pathologies such as cardiovascular diseases ago.

  17. Technology Summary Advancing Tank Waste Retrieval And Processing

    International Nuclear Information System (INIS)

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them. This technology overview provides a high-level summary of technologies being investigated, developed, and deployed by WRPS to advance Hanford Site tank waste retrieval and processing. Transformational technologies are needed to complete Hanford tank waste retrieval and treatment by 12/31/2047. Hanford's underground waste storage tanks hold approximately 57 million gallons of radiochemical waste from nuclear defense production - more tank waste than any other site in the United States. In addition, the waste is uniquely complicated because it contains constituents from at least six major radiochemical processes and several lesser processes. It is intermixed and complexed more than any other waste collection known to exist in the world. The multi-faceted nature of Hanford's tank waste means that legally binding agreements in the Federal Facility Agreement and Consent Order (known as the Tri-Party Agreement) and between the Department of Energy (DOE) and its contractors may not be met using current vitrification schedules, plans, and methods. WRPS and the DOE are developing, testing, and deploying technologies to meet the necessary commitments and complete the DOE's River Protection Project (RPP) mission within environmentally acceptable requirements. Technology solutions are outlined, along with processes and priorities for selecting and developing them. DOE's Office of Environmental Management (EM) identifies the environmental management technology needs and the activities necessary to address them. The U.S. Congress then funds these activities through EM or the DOE field offices. Finally, an array of entities that include DOE site prime contractors and

  18. Iron-oxidation processes in an electroflocculation (electrocoagulation) cell

    International Nuclear Information System (INIS)

    The processes of iron oxidation in an electroflocculation cell were investigated for a pH range of 5-9 and electric currents of 0.05-0.4 A (equivalent current densities of 8.6-69 A/m2). At all pH values and electric currents investigated, it was demonstrated and proven that for all practical purposes, the form of iron that dissolves from the anode is Fe2+ (ferrous). The difference between the amount of theoretical dissolution as calculated by Faraday's law and the amount of observed dissolved iron ions may indicate two phenomena in electrochemical cells. The first is possible dissolution of the anode even without the operation of an electric current; this led to higher theoretical dissolution rates at lower pH. The second is the participation of some of the electrons of the electric current in reactions other than anode dissolution which led to lower theoretical dissolution rates at higher pH. Those other reactions did not lead to an increase in the local oxidation saturation level near the anode and did not affect iron-oxidation rates in the electroflocculation processes. The oxidation rates of the dissolved Fe2+ (ferrous) to Fe3+ (ferric) ions in electroflocculation processes were strongly dependent on the pH and were similar to the known oxidation rates of iron in non-electrochemical cells.

  19. Iron-oxidation processes in an electroflocculation (electrocoagulation) cell

    Energy Technology Data Exchange (ETDEWEB)

    Sasson, Moshe Ben, E-mail: mosheinspain@hotmail.com [Department of Soil and Water Sciences, Robert H. Smith Faculty of Agriculture, Food and Environment, Hebrew University of Jerusalem, Rehovot 76100 (Israel); Calmano, Wolfgang [Institute of Environmental Technology and Energy Economics, Technical University of Hamburg-Harburg, 21073 Hamburg (Germany); Adin, Avner [Department of Soil and Water Sciences, Robert H. Smith Faculty of Agriculture, Food and Environment, Hebrew University of Jerusalem, Rehovot 76100 (Israel)

    2009-11-15

    The processes of iron oxidation in an electroflocculation cell were investigated for a pH range of 5-9 and electric currents of 0.05-0.4 A (equivalent current densities of 8.6-69 A/m{sup 2}). At all pH values and electric currents investigated, it was demonstrated and proven that for all practical purposes, the form of iron that dissolves from the anode is Fe{sup 2+} (ferrous). The difference between the amount of theoretical dissolution as calculated by Faraday's law and the amount of observed dissolved iron ions may indicate two phenomena in electrochemical cells. The first is possible dissolution of the anode even without the operation of an electric current; this led to higher theoretical dissolution rates at lower pH. The second is the participation of some of the electrons of the electric current in reactions other than anode dissolution which led to lower theoretical dissolution rates at higher pH. Those other reactions did not lead to an increase in the local oxidation saturation level near the anode and did not affect iron-oxidation rates in the electroflocculation processes. The oxidation rates of the dissolved Fe{sup 2+} (ferrous) to Fe{sup 3+} (ferric) ions in electroflocculation processes were strongly dependent on the pH and were similar to the known oxidation rates of iron in non-electrochemical cells.

  20. Advances in Process Intensification through Multifunctional Reactor Engineering

    Energy Technology Data Exchange (ETDEWEB)

    O' Hern, Timothy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Engineering Sciences Center; Evans, Lindsay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Materials Sciences and Engineering Center; Miller, Jim [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Materials Sciences and Engineering Center; Cooper, Marcia [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Energetic Components Realization Center; Torczynski, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pena, Donovan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gill, Walt [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Engineering Sciences Center

    2011-02-01

    This project was designed to advance the art of process intensification leading to a new generation of multifunctional chemical reactors utilizing pulse flow. Experimental testing was performed in order to fully characterize the hydrodynamic operating regimes associated with pulse flow for implementation in commercial applications. Sandia National Laboratories (SNL) operated a pilot-scale multifunctional reactor experiment for operation with and investigation of pulse flow operation. Validation-quality data sets of the fluid dynamics, heat and mass transfer, and chemical kinetics were acquired and shared with Chemical Research and Licensing (CR&L). Experiments in a two-phase air-water system examined the effects of bead diameter in the packing, and viscosity. Pressure signals were used to detect pulsing. Three-phase experiments used immiscible organic and aqueous liquids, and air or nitrogen as the gas phase. Hydrodynamic studies of flow regimes and holdup were performed for different types of packing, and mass transfer measurements were performed for a woven packing. These studies substantiated the improvements in mass transfer anticipated for pulse flow in multifunctional reactors for the acid-catalyzed C4 paraffin/olefin alkylation process. CR&L developed packings for this alkylation process, utilizing their alkylation process pilot facilities in Pasadena, TX. These packings were evaluated in the pilot-scale multifunctional reactor experiments established by Sandia to develop a more fundamental understanding of their role in process intensification. Lummus utilized the alkylation technology developed by CR&L to design and optimize the full commercial process utilizing multifunctional reactors containing the packings developed by CR&L and evaluated by Sandia. This hydrodynamic information has been developed for multifunctional chemical reactors utilizing pulse flow, for the acid-catalyzed C4 paraffin/olefin alkylation process, and is now accessible for use in