The Proceedings of Joint 28th ICFA Advanced Beam Dynamics and Advanced Nova Accelerator Workshops on Quantum Aspects of Beam Physics

International Nuclear Information System (INIS)

Chen, P

2004-01-01

The Joint 28th ICFA (International Committee for Future Accelerators) Advanced Beam Dynamics and Advanced and Novel Accelerators Workshop on ''QUANTUM ASPECTS OF BEAM PHYSICS and Other Critical Issues of Beams in Physics and Astrophysics'', was held on January 7-11, 2003, in Hiroshima, Japan. This was the third in the QABP workshop series. The first QABP workshop was launched in January 1998, in Monterey, California, and the second was held in October 2000, in Capri, Italy. Over the past five years, this workshop series has passed its torch around the world, from the U.S. to Europe, and this time to Japan in Asia. Following the footsteps of the first two workshops, this one in Hiroshima was again a tremendous success. The frontier of beam research points to increasingly higher energy, greater brightness and lower emittance beams with ever-increasing particle species. These demands have triggered a rapidly growing number of beam phenomena that involve quantum effects. With the significant advancement of laser and accelerator technologies, there is also a growing interest in using high energy, high intensity particle and photon beams for laboratory astrophysics investigations, as well as the application of beam physics expertise to astrophysics studies. It has therefore become a tradition that this workshop series attracted a broad spectrum of experts from beam physics, astrophysics, cosmology, particle physics, condensed matter physics, nuclear physics, atomic physics, and laser science, to explore a common frontier where their individual expertise and interests overlapped

Japan-IAEA Workshops on Advanced Safeguards for Future Nuclear Fuel Cycles

International Nuclear Information System (INIS)

Hoffheins, B.; Hori, M.; Suzuki, M.; Kuno, Y.; Kimura, N.; Naito, K.; Hosoya, M.; Khlebnikov, N.; Whichello, J.; Zendel, M.

2010-01-01

Beginning in 2007, the Japan Atomic Energy Agency (JAEA) and the International Atomic Energy Agency (IAEA) Department of Safeguards initiated a workshop series focused on advanced safeguards technologies for the future nuclear fuel cycle (NFC). The goals for these workshops were to address safeguards challenges, to share implementation experiences, to discuss fuel cycle plans and promising research and development, and to address other issues associated with safeguarding new fuel cycle facilities. Concurrently, the workshops also served to promote dialog and problem solving, and to foster closer collaborations for facility design and planning. These workshops have sought participation from IAEA Member States' support programmes (MSSP), the nuclear industry, R and D organizations, state systems of accounting and control (SSAC), regulators and inspectorates to ensure that all possible stakeholder views can be shared in an open process. Workshop presentations have covered, inter alia, national fuel cycle programs and plans, research progress in proliferation resistance (PR) and safeguardability, approaches for nuclear measurement accountancy of large material throughputs and difficult to access material, new and novel radiation detectors with increased sensitivity and automation, and lessons learned from recent development and operation of safeguards systems for complex facilities and the experiences of integrated safeguards (IS) in Japan. Although the title of the workshops presumes an emphasis on technology, participants recognized that early planning and organization, coupled with close cooperation among stakeholders, that is, through the application of 'Safeguards by Design' (SBD) processes that include nuclear safety and security coordination, 'Remote Inspections' and 'Joint-Use of Equipment (JUE)' would be required to enable more successful implementations of safeguards at future NFC facilities. The needs to cultivate the future workforce, effectively preserve

Advanced Wind Turbine Drivetrain Concepts: Workshop Report, June 29-30, 2010

Energy Technology Data Exchange (ETDEWEB)

DOE, EERE

2010-12-01

This report presents key findings from the Department of Energy's Advanced Drivetrain Workshop, held on June 29-30, 2010 in Broomfield, Colorado, to assess different advanced drivetrain technologies, their relative potential to improve the state-of-the-art in wind turbine drivetrains, and the scope of research and development needed for their commercialization in wind turbine applications.

Recommendations of the workshop on advanced geothermal drilling systems

Energy Technology Data Exchange (ETDEWEB)

Glowka, D.A.

1997-12-01

At the request of the U.S. Department of Energy, Office of Geothermal Technologies, Sandia National Laboratories convened a group of drilling experts in Berkeley, CA, on April 15-16, 1997, to discuss advanced geothermal drilling systems. The objective of the workshop was to develop one or more conceptual designs for an advanced geothermal drilling system that meets all of the criteria necessary to drill a model geothermal well. The drilling process was divided into ten essential functions. Each function was examined, and discussions were held on the conventional methods used to accomplish each function and the problems commonly encountered. Alternative methods of performing each function were then listed and evaluated by the group. Alternative methods considered feasible or at least worth further investigation were identified, while methods considered impractical or not potentially cost-saving were eliminated from further discussion. This report summarizes the recommendations of the workshop participants. For each of the ten functions, the conventional methods, common problems, and recommended alternative technologies and methods are listed. Each recommended alternative is discussed, and a description is given of the process by which this information will be used by the U.S. DOE to develop an advanced geothermal drilling research program.

Proceedings of the Third International Workshop on Advances in Electrocorticography.

NARCIS (Netherlands)

Ritaccio, A.; Beauchamp, M.; Bosman, C.; Brunner, P.; Chang, E.; Crone, N.; Gunduz, A.; Gupta, D.; Knight, R.; Leuthardt, E.; Litt, B.; Moran, D.; Ojemann, J.; Parvizi, K.; Ramsey, N.; Rieger, J.; Viventi, J.; Voytek, B.; Williams, J.; Schalk, G.

2012-01-01

The Third International Workshop on Advances in Electrocorticography (ECoG) was convened in Washington, DC, on November 10-11, 2011. As in prior meetings, a true multidisciplinary fusion of clinicians, scientists, and engineers from many disciplines gathered to summarize contemporary experiences in

Workshop on Advanced Technologies for Planetary Instruments, part 1

International Nuclear Information System (INIS)

Appleby, J.F.

1993-01-01

This meeting was conceived in response to new challenges facing NASA's robotic solar system exploration program. This volume contains papers presented at the Workshop on Advanced Technologies for Planetary Instruments on 28-30 Apr. 1993. This meeting was conceived in response to new challenges facing NASA's robotic solar system exploration program. Over the past several years, SDIO has sponsored a significant technology development program aimed, in part, at the production of instruments with these characteristics. This workshop provided an opportunity for specialists from the planetary science and DOD communities to establish contacts, to explore common technical ground in an open forum, and more specifically, to discuss the applicability of SDIO's technology base to planetary science instruments

Report of the advanced neutron source (ANS) aluminum cladding corrosion workshop

International Nuclear Information System (INIS)

Hanson, G.H.; Gibson, G.W.; Griess, J.C.; Pawel, R.E.; Pace, N.E.; Ryskamp, J.M.

1989-02-01

The Advanced Neutron Source (ANS) Corrosion Workshop on aluminum cladding corrosion in reactor environments is summarized. The Workshop was held to examine the aluminum cladding oxidation studies being conducted in support of the ANS design. This report was written principally to provide a record of the ideas and judgments expressed by the workshop attendees. The ANS operating heat flux is significantly higher than that in existing reactors, and early experiments indicate that there may be an aluminum cladding oxidation problem unique to higher heat fluxes or associated cladding temperatures that, if not solved, may limit the operation of the ANS to unacceptably low power levels. A brief description of the information presented by each speaker is included along with a compilation of the most significant ideas and recommended research areas. The appendixes contain a copy of the workshop agenda and a list of attendees

NATO Advanced Research Workshop on the Mechanisms of Reactions of Organometallic Compounds with Surfaces

CERN Document Server

Williams, J

1989-01-01

A NATO Advanced Research Workshop on the "Mechanisms of Reactions of Organometallic Compounds with Surfaces" was held in St. Andrews, Scotland in June 1988. Many of the leading international researchers in this area were present at the workshop and all made oral presentations of their results. In addition, significant amounts of time were set aside for Round Table discussions, in which smaller groups considered the current status of mechanistic knowledge, identified areas of dispute or disagreement, and proposed experiments that need to be carried out to resolve such disputes so as to advance our understanding of this important research area. All the papers presented at the workshop are collected in this volume, together with summaries of the conclusions reached at the Round Table discussions. The workshop could not have taken place without financial support from NATO, and donations were also received from Associated Octel, Ltd., STC Ltd., and Epichem Ltd., for which the organisers are very grateful. The orga...

Advanced Power Electronics Interfaces for Distributed Energy Workshop Summary: August 24, 2006, Sacramento, California

Energy Technology Data Exchange (ETDEWEB)

Treanton, B.; Palomo, J.; Kroposki, B.; Thomas, H.

2006-10-01

The Advanced Power Electronics Interfaces for Distributed Energy Workshop, sponsored by the California Energy Commission Public Interest Energy Research program and organized by the National Renewable Energy Laboratory, was held Aug. 24, 2006, in Sacramento, Calif. The workshop provided a forum for industry stakeholders to share their knowledge and experience about technologies, manufacturing approaches, markets, and issues in power electronics for a range of distributed energy resources. It focused on the development of advanced power electronic interfaces for distributed energy applications and included discussions of modular power electronics, component manufacturing, and power electronic applications.

Workshop on Advanced Modelling in Mathematical Finance : in Honour of Ernst Eberlein

CERN Document Server

Papapantoleon, Antonis

2016-01-01

This Festschrift resulted from a workshop on “Advanced Modelling in Mathematical Finance” held in honour of Ernst Eberlein’s 70th birthday, from 20 to 22 May 2015 in Kiel, Germany. It includes contributions by several invited speakers at the workshop, including several of Ernst Eberlein’s long-standing collaborators and former students. Advanced mathematical techniques play an ever-increasing role in modern quantitative finance. Written by leading experts from academia and financial practice, this book offers state-of-the-art papers on the application of jump processes in mathematical finance, on term-structure modelling, and on statistical aspects of financial modelling. It is aimed at graduate students and researchers interested in mathematical finance, as well as practitioners wishing to learn about the latest developments.

13th European Workshop on Advanced Control and Diagnosis (ACD 2016)

International Nuclear Information System (INIS)

2017-01-01

13 th European Workshop on Advanced Control and Diagnosis The 13th European Workshop on Advanced Control and Diagnosis (ACD 2016), www.acd2016.eu took place at Hautes Etrudes d’Ingénieur (HEI), Lille, France, on November 17-18, 2016. The annual European Workshop on Advanced Control and Diagnosis has been organized since 2003 by Control Engineering departments of several European universities in Germany, France, the UK, Poland, Italy, Hungary, Denmark and Czech Republic, to bring together senior and junior academics and engineers from diverse fields of automatic control, fault detection, and signal processing. The workshop provides an opportunity for researchers and developers to present their recent theoretical developments, practical applications, or even open problems. It also offers a great opportunity for industrial partners to express their needs and priorities and to review the current activities in the fields. A total of 100 papers have been submitted for ACD 2016. Based on the peer reviews 71 papers were accepted for oral presentation, 4 papers withdrawn, 3 papers not presented. The accepted papers covered areas of Fault Diagnosis, Estimation and Observation, Fault Tolerant Control, Predictive Control, Robust Control, Control Theory, fractional order systems, Modeling and Data °Processing, Software tools and code generation. In addition, four excellent plenary lectures were delivered by experts on their domain: Ir. Serge Legonidec from the company Airbus Safran Launchers, France : An overview of connections between scientific automatic topics and their applications in the propulsive systems, Dr. Ir. Jan-Willem Van Wingerden, Technical University of Delft, Nederland : Wind Energy Control Research, Prof. Sarah Spurgeon, University College London, UK: On discontinuous Observers: From Basic Properties to a Robust Fault Detection and Condition Monitoring Tool, Dr. Joseph-Julien Yame, University of Lorraine, Nancy, France : Data Driven Fault Tolerant Control

Atomic physics at the Advanced Photon Source: Workshop report

International Nuclear Information System (INIS)

1990-10-01

The first Workshop on Atomic Physics at the Advanced Photon Source was held at Argonne National Laboratory on March 29--30, 1990. The unprecedented brightness of the Advanced Photon Source (APS) in the hard X-ray region is expected to make possible a vast array of new research opportunities for the atomic-physics community. Starting with discussions of the history and current status of the field, presentations were made on various future directions for research with hard X-rays interacting with atoms, ions, clusters, and solids. Also important were the discussions on the design and status of the four next-generation rings coming on line during the 1990's: the ALS 1.6 GeV ring at Berkeley; the ESRF 6.0-GeV ring at Grenoble (1993); the APS 7.0-GeV ring at Argonne (1995); and the SPring-8 8.0-GeV ring in Japan (1998). The participation of more than one hundred scientists from domestic as well as foreign institutions demonstrated a strong interest in this field. We plan to organize follow-up workshops in the future emphasizing specific research topics

Grand Challenges of Advanced Computing for Energy Innovation Report from the Workshop Held July 31-August 2, 2012

Energy Technology Data Exchange (ETDEWEB)

Larzelere, Alex R.; Ashby, Steven F.; Christensen, Dana C.; Crawford, Dona L.; Khaleel, Mohammad A.; John, Grosh; Stults, B. Ray; Lee, Steven L.; Hammond, Steven W.; Grover, Benjamin T.; Neely, Rob; Dudney, Lee Ann; Goldstein, Noah C.; Wells, Jack; Peltz, Jim

2013-03-06

On July 31-August 2 of 2012, the U.S. Department of Energy (DOE) held a workshop entitled Grand Challenges of Advanced Computing for Energy Innovation. This workshop built on three earlier workshops that clearly identified the potential for the Department and its national laboratories to enable energy innovation. The specific goal of the workshop was to identify the key challenges that the nation must overcome to apply the full benefit of taxpayer-funded advanced computing technologies to U.S. energy innovation in the ways that the country produces, moves, stores, and uses energy. Perhaps more importantly, the workshop also developed a set of recommendations to help the Department overcome those challenges. These recommendations provide an action plan for what the Department can do in the coming years to improve the nation’s energy future.

Proceedings of the NATO Advanced Research Workshop on Countering Nuclear and Radiological Terrorism

International Nuclear Information System (INIS)

Apikyan, S.; Diamond, D.

2006-01-01

The objective of this workshop was to identify connections between technology needs and the underlying science and technology, and to establish research strategies that will advanced our ability to counter this form of terrorism. The objectives were met by bringing together international experts familiar with the relevant technologies and policies at a four-day workshop that was held at the Regional Advanced Science and Technology Center (ASTEC), Yerevan, Armenia during October 2005. The many topics covered included: radiation detector development, risk assessment and decision making, decontamination techniques, structural materials resistance to conventional explosives, vulnerability and physical protection of nuclear facilities, security of radiation sources, response to radiological dispersion devices, relevant international and national laws, and non-proliferation

NATO Advanced Research Workshop on Earth Rotation : Solved and Unsolved Problems

CERN Document Server

1986-01-01

The idea for organl.zl.ng an Advanced Research Workshop entirely devoted to the Earth rotation was born in 1983 when Professor Raymond Hide suggested this topic to the special NATO panel of global transport mechanism in the Geosciences. Such a specialized meeting did not take place since the GEOP research conference on the rotation of the Earth and polar motion which was held at the Ohio State University (USA) in 1973. In the last ten years, highly precise measurements of the Earth's rotation parameters and new global geophysical data have become available allowing major advance to be made in the under­ standing of the various irregularities affecting the Earth's rotation. The aim of the workshop was to bring together scientists who have made important contributions in this field during the last decade both at the observational and geophysical interpretation levels. The confe­ rence was divided into four main topics. The first session was dedicated to the definition, implementation and maintenance of the te...

Instrumentation for the advanced high-flux reactor workshop: proceedings

International Nuclear Information System (INIS)

Moon, R.M.

1984-01-01

The purpose of the Workshop on Instrumentation for the Advanced High-Flux Reactor, held on May 30, 1984, at the Oak Ridge National Laborattory, was two-fold: to announce to the scientific community that ORNL has begun a serious effort to design and construct the world's best research reactor, and to solicit help from the scientific community in planning the experimental facilities for this reactor. There were 93 participants at the workshop. We are grateful to the visiting scientists for their enthusiasm and interest in the reactor project. Our goal is to produce a reactor with a peak thermal flux in a large D 2 O reflector of 5 x 10 15 n/cm 2 s. This would allow the installation of unsurpassed facilities for neutron beam research. At the same time, the design will provide facilities for isotope production and materials irradiation which are significantly improved over those now available at ORNL. This workshop focussed on neutron beam facilities; the input from the isotope and materials irradiation communities will be solicited separately. The reactor project enjoys the full support of ORNL management; the present activities are financed by a grant of $663,000 from the Director's R and D Fund. However, we realize that the success of the project, both in realization and in use of the reactor, depends on the support and imagination of a broad segment of the scientific community. This is more a national project than an ORNL project. The reactor would be operated as a national user facility, open to any research proposal with high scientific merit. It is therefore important that we maintain a continuing dialogue with outside scientists who will be the eventual users of the reactor and the neutron beam facilities. The workshop was the first step in establishing this dialogue; we anticipate further workshops as the project continues

Seeking the Tricorder: Report on Workshops on Advanced Technologies for Life Detection

Science.gov (United States)

Reiss-Bubenheim, D.; Boston, P. J.; Partridge, H.; Lindensmith, C.; Nadeau, J. L.

2017-12-01

There's great excitement about life prospects on icy fluid-containing moons orbiting our Solar System's gas giant planets, newly discovered planet candidates and continuing long-term interest in possible Mars life. The astrobiology/planetary research communities require advanced technologies to explore and study both Solar System bodies and exoplanets for evidence of life. The Tricorder Workshop, held at Ames Research Center May 19-20, 2017, explored technology topics focused on non-invasive or minimally invasive methods for life detection. The workshop goal was to tease out promising ideas for low TRL concepts for advanced life detection technologies that could be applied to the surface and near-subsurface of Mars and Ocean Worlds (such as Europa and Enceladus) dominated by icy terrain. The workshop technology focus centered on mid-to-far term instrument concepts or other enabling technologies (e.g. robotics, machine learning, etc.) primarily for landed missions, which could detect evidence of extant, extinct and/or "weird" life including the notion of "universal biosignatures". Emphasis was placed on simultaneous and serial sample measurements using a suite of instruments and technological approaches with planetary protection in mind. A follow-on workshop, held July 24 at Caltech, sought to develop a generic flowchart of in situ observations and measurements to provide sufficient information to determine if extant life is present in an environment. The process didn't require participant agreement as to definition of extant life, but instead developed agreement on necessary observations and instruments. The flowchart of measurements was designed to maximize the number of simultaneous observations on a single sample where possible, serializing where necessary, and finally dividing it into parts for the most destructive analyses at the end. Selected concepts from the workshops outlined in this poster provide those technology areas necessary to solicit and develop

Proceedings of the Workshop on Advanced Network and Technology Concepts for Mobile, Micro, and Personal Communications

Science.gov (United States)

Paul, Lori (Editor)

1991-01-01

The Workshop on Advanced Network and Technology Concepts for Mobile, Micro, and Personal Communications was held at NASA's JPL Laboratory on 30-31 May 1991. It provided a forum for reviewing the development of advanced network and technology concepts for turn-of-the-century telecommunications. The workshop was organized into three main categories: (1) Satellite-Based Networks (L-band, C-band, Ku-band, and Ka-band); (2) Terrestrial-Based Networks (cellular, CT2, PCN, GSM, and other networks); and (3) Hybrid Satellite/Terrestrial Networks. The proceedings contain presentation papers from each of the above categories.

Proceedings of the workshop on advanced thermal-hydraulic and neutronic codes: current and future applications

International Nuclear Information System (INIS)

2001-01-01

An OECD Workshop on Advanced Thermal-Hydraulic and Neutronic Codes Applications was held from 10 to 13 April 2000, in Barcelona, Spain, sponsored by the Committee on the Safety of Nuclear Installations (CSNI) of the OECD Nuclear Energy Agency (NEA). It was organised in collaboration with the Spanish Nuclear Safety Council (CSN) and hosted by CSN and the Polytechnic University of Catalonia (UPC) in collaboration with the Spanish Electricity Association (UNESA). The objectives of the Workshop were to review the developments since the previous CSNI Workshop held in Annapolis [NEA/CSNI/ R(97)4; NUREG/CP-0159], to analyse the present status of maturity and remnant needs of thermal-hydraulic (TH) and neutronic system codes and methods, and finally to evaluate the role of these tools in the evolving regulatory environment. The Technical Sessions and Discussion Sessions covered the following topics: - Regulatory requirements for Best-Estimate (BE) code assessment; - Application of TH and neutronic codes for current safety issues; - Uncertainty analysis; - Needs for integral plant transient and accident analysis; - Simulators and fast running codes; - Advances in next generation TH and neutronic codes; - Future trends in physical modeling; - Long term plans for development of advanced codes. The focus of the Workshop was on system codes. An incursion was made, however, in the new field of applying Computational Fluid Dynamic (CFD) codes to nuclear safety analysis. As a general conclusion, the Barcelona Workshop can be considered representative of the progress towards the targets marked at Annapolis almost four years ago. The Annapolis Workshop had identified areas where further development and specific improvements were needed, among them: multi-field models, transport of interfacial area, 2D and 3D thermal-hydraulics, 3-D neutronics consistent with level of details of thermal-hydraulics. Recommendations issued at Annapolis included: developing small pilot/test codes for

International workshop on advanced materials for high precision detectors. Proceedings

International Nuclear Information System (INIS)

Nicquevert, B.; Hauviller, C.

1994-01-01

These proceedings gather together the contributions to the Workshop on Advanced Materials for High Precision Detectors, which was held from 28-30 September 1994 in Archamps, Haute-Savoie, France. This meeting brought together international experts (researchers, physicists and engineers) in the field of advanced materials and their use in high energy physics detectors or spacecraft applications. Its purpose was to discuss the status of the different materials currently in use in the structures of detectors and spacecraft, together with their actual performances, technological implications and future prospects. Environmental effects, such as those of moisture and radiation, were discussed, as were design and manufacturing technologies. Some case studies were presented. (orig.)

Organization of the 16th Advanced Accelerator Concepts (AAC) Workshop by Stanford University

Energy Technology Data Exchange (ETDEWEB)

Huang, Zhirong [Stanford Univ., CA (United States); Hogan, Mark [Stanford Univ., CA (United States)

2015-09-30

Essentially all we know today and will learn in the future about the fundamental nature of matter is derived from probing it with directed beams of particles such as electrons, protons, neutrons, heavy ions, and photons. The resulting ability to “see” the building blocks of matter has had an immense impact on society and our standard of living. Over the last century, particle accelerators have changed the way we look at nature and the universe we live in and have become an integral part of the Nation’s technical infrastructure. Today, particle accelerators are essential tools of modern science and technology. The cost and capabilities of accelerators would be greatly enhanced by breakthroughs in acceleration methods and technology. For the last 32 years, the Advanced Accelerator Concepts (AAC) Workshop has acted as the focal point for discussion and development of the most promising acceleration physics and technology. It is a particularly effective forum where the discussion is leveraged and promoted by the unique and demanding feature of the AAC Workshop: the working group structure, in which participants are asked to consider their contributions in terms of even larger problems to be solved. The 16th Advanced Accelerator Concepts (AAC2014) Workshop was organized by Stanford University from July 13 - 18, 2014 at the Dolce Hays Mansion in San Jose, California. The conference had a record 282 attendees including 62 students. Attendees came from 11 countries representing 66 different institutions. The workshop format consisted of plenary sessions in the morning with topical leaders from around the world presenting the latest breakthroughs to the entire workshop. In the late morning and afternoons attendees broke out into eight different working groups for more detailed presentations and discussions that were summarized on the final day of the workshop. In addition, there were student tutorial presentations on two afternoons to provide in depth education and

78 FR 49530 - Gastroenterology Regulatory Endpoints and the Advancement of Therapeutics; Public Workshop

Science.gov (United States)

2013-08-14

...] Gastroenterology Regulatory Endpoints and the Advancement of Therapeutics; Public Workshop AGENCY: Food and Drug... for Drug Evaluation and Research, in cosponsorship with the American College of Gastroenterology, the... American Society for Pediatric Gastroenterology, Hepatology, and Nutrition, and the Pediatric IBD...

25th workshop on Advances in Analog Circuit Design

CERN Document Server

Harpe, Pieter; Makinwa, Kofi

2017-01-01

This book is based on the 18 tutorials presented during the 25th workshop on Advances in Analog Circuit Design. Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, including low-power and energy-efficient analog electronics, with specific contributions focusing on the design of continuous-time sigma-delta modulators, automotive electronics, and power management. This book serves as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.

Advances in complex reservoir evaluation based on geophysical well logs

Energy Technology Data Exchange (ETDEWEB)

Fertl, W.H.; Sinha, A.K. (Western Atlas International, Inc., Houston, TX (USA)); McDougall, J.G. (Western Atlas Canada Ltd., Calgary, AB (Canada))

1988-09-01

The matrix of reservoirs having complex lithologies, cause different density, neutron, and acoustic responses. Therefore the lithologies and effective porosity of reservoirs can be determined by using various crossplot techniques on data collected from two of these logs. The Complex Reservoir Analysis program (CRA) computes lithology, porosity, water saturation and relative permeabilities in formations with interbedded limestone, dolomite, and anhydrite. Porosity options include crossplot and individual log response techniques. Corrections for light hydrocarbons were applied. In solving for porosity and mineral volumes, sand, limestone, dolomite, and anhydrite lines were defined on either density/neutron or neutron/acoustic crossplots. Four additional mineral lines were specified. Incorporation of Pe data from the Z-Densilog provided a significant advance in evaluating complex reservoirs via the Z-CRA analysis. The classic reservoir evaluation program CLASS, was used to perform both minerals and shaly evaluation based on density, neutron, resistivity, and natural gamma ray spectral measurements. Computations included total and effective porosities, fluid saturation distribution based on the Wasman-Smits model, productivity indices, and volume and distribution of clay minerals. Additional computed formation parameters included log-derived cation exchange capacity and hydrogen index of dry clay matrix to determine the type and amount of smectite, illite and chlorite/kaolinite present. Canadian field experiences was used to illustrate and support the techniques described. 11 refs., 11 figs., 6 tabs.

U.S. DOE Roundtable and Workshop on Advanced Steel Technologies: Emerging Global Technologies and R&D Opportunities

Energy Technology Data Exchange (ETDEWEB)

Pellegrino, Joan [Energetics, Inc., Columbia, MD (United States); Jamison, Keith [Energetics, Inc., Columbia, MD (United States)

2015-12-01

This report is based on the proceedings of the U.S. DOE Roundtable and Workshop on Advanced Steel Technologies Workshop hosted by Oak Ridge National Laboratory (ORNL) in cooperation with the U.S. Department of Energy s (DOE s) Advanced Manufacturing Office (AMO) on held on June 23, 2015. Representatives from industry, government, and academia met at the offices of the National Renewable Energy Laboratory in Washington, DC, to share information on emerging steel technologies, issues impacting technology investment and deployment, gaps in research and development (R&D), and opportunities for greater energy efficiency. The results of the workshop are summarized in this report. They reflect a snapshot of the perspectives and ideas generated by the individuals who attended and not all-inclusive of the steel industry and stakeholder community.

International on Workshop Advances in Laboratory Testing & Modelling of Soils and Shales

CERN Document Server

Laloui, Lyesse

2017-01-01

In this spirit, the ATMSS International Workshop “Advances in Laboratory Testing & Modelling of Soils and Shales” (Villars-sur-Ollon, Switzerland; 18-20 January 2017) has been organized to promote the exchange of ideas, experience and state of the art among major experts active in the field of experimental testing and modelling of soils and shales. The Workshop has been organized under the auspices of the Technical Committees TC-101 “Laboratory Testing”, TC-106 “Unsaturated Soils” and TC-308 “Energy Geotechnics” of the International Society of Soil Mechanics and Geotechnical Engineering. This volume contains the invited keynote and feature lectures, as well as the papers that have been presented at the Workshop. The topics of the lectures and papers cover a wide range of theoretical and experimental research, including unsaturated behaviour of soils and shales, multiphysical testing of geomaterials, hydro–mechanical behaviour of shales and stiff clays, the geomechanical behaviour of the ...

Cross-system log file analysis for hypothesis testing

NARCIS (Netherlands)

Glahn, Christian

2008-01-01

Glahn, C. (2008). Cross-system log file analysis for hypothesis testing. Presented at Empowering Learners for Lifelong Competence Development: pedagogical, organisational and technological issues. 4th TENCompetence Open Workshop. April, 10, 2008, Madrid, Spain.

Summary of 2017 NASA Workshop on Assessment of Advanced Battery Technologies for Aerospace Applications

Science.gov (United States)

Misra, Ajay

2018-01-01

A workshop on assessment of battery technologies for future aerospace applications was held in Cleveland, OH on August 16-17. The focus of the workshop, hosted by NASA GRC, was to assess (1) the battery needs for future aerospace missions, (2) the state of battery technology and projected technology advances, and (3) the need for additional investments for future aerospace missions. The workshop had 109 attendees that included internationally recognized technology leaders from academia and national laboratories, high level executives from government and industry, small businesses, and startup companies. A significant portion of the workshop was focused on batteries for electrified aircraft. The presentation will summarize the finding on the state of battery technologies for electrified aircraft and will include assessment of current state of battery technology, gaps in battery technology for application in electrified aircraft, and recommended technology development options for meeting near-term and long-term needs of electrified aircraft.

The first international workshop on "Advancement of POLarimetric Observations: calibration and improved aerosol retrievals": APOLO-2017

Science.gov (United States)

Dubovik, Oleg; Li, Zhengqiang; Mishchenko, Michael I.

2018-06-01

The international workshop on "Advancement of POLarimetric Observations: calibration and improved aerosol retrievals-2017" (APOLO-2017) took place in Hefei, China on 24 - 27 October 2017. This was the inaugural meeting of a planned series of workshops on satellite polarimetry aimed at addressing the rapidly growing interest of the scientific community in polarimetric remote-sensing observations from space. The workshop was held at the Anhui Institute of Optics and Fine Mechanics, Hefei, widely known for 15 years of experience in the development of research polarimetry sensors and for hosting the building in parallel of several orbital polarimeters.

HTTR workshop (workshop on hydrogen production technology)

International Nuclear Information System (INIS)

Shiina, Yasuaki; Takizuka, Takakazu

2004-12-01

Various research and development efforts have been performed to solve the global energy and environmental problems caused by large consumption of fossil fuels. Research activities on advanced hydrogen production technology by the use of nuclear heat from high temperature gas cooled reactors, for example, have been flourished in universities, research institutes and companies in many countries. The Department of HTTR Project and the Department of Advanced Nuclear Heat Technology of JAERI held the HTTR Workshop (Workshop on Hydrogen Production Technology) on July 5 and 6, 2004 to grasp the present status of R and D about the technology of HTGR and the nuclear hydrogen production in the world and to discuss about necessity of the nuclear hydrogen production and technical problems for the future development of the technology. More than 110 participants attended the Workshop including foreign participants from USA, France, Korea, Germany, Canada and United Kingdom. In the Workshop, the presentations were made on such topics as R and D programs for nuclear energy and hydrogen production technologies by thermo-chemical or other processes. Also, the possibility of the nuclear hydrogen production in the future society was discussed. The workshop showed that the R and D for the hydrogen production by the thermo-chemical process has been performed in many countries. The workshop affirmed that nuclear hydrogen production could be one of the competitive supplier of hydrogen in the future. The second HTTR Workshop will be held in the autumn next year. (author)

16th International workshop on Advanced Computing and Analysis Techniques in physics (ACAT)

CERN Document Server

Lokajicek, M; Tumova, N

2015-01-01

16th International workshop on Advanced Computing and Analysis Techniques in physics (ACAT). The ACAT workshop series, formerly AIHENP (Artificial Intelligence in High Energy and Nuclear Physics), was created back in 1990. Its main purpose is to gather researchers related with computing in physics research together, from both physics and computer science sides, and bring them a chance to communicate with each other. It has established bridges between physics and computer science research, facilitating the advances in our understanding of the Universe at its smallest and largest scales. With the Large Hadron Collider and many astronomy and astrophysics experiments collecting larger and larger amounts of data, such bridges are needed now more than ever. The 16th edition of ACAT aims to bring related researchers together, once more, to explore and confront the boundaries of computing, automatic data analysis and theoretical calculation technologies. It will create a forum for exchanging ideas among the fields an...

NATO Advanced Research Workshop on Thin Film Growth Techniques for Low-Dimensional Structures

CERN Document Server

Parkin, S; Dobson, P; Neave, J; Arrott, A

1987-01-01

This work represents the account of a NATO Advanced Research Workshop on "Thin Film Growth Techniques for Low Dimensional Structures", held at the University of Sussex, Brighton, England from 15-19 Sept. 1986. The objective of the workshop was to review the problems of the growth and characterisation of thin semiconductor and metal layers. Recent advances in deposition techniques have made it possible to design new material which is based on ultra-thin layers and this is now posing challenges for scientists, technologists and engineers in the assessment and utilisation of such new material. Molecular beam epitaxy (MBE) has become well established as a method for growing thin single crystal layers of semiconductors. Until recently, MBE was confined to the growth of III-V compounds and alloys, but now it is being used for group IV semiconductors and II-VI compounds. Examples of such work are given in this volume. MBE has one major advantage over other crystal growth techniques in that the structure of the growi...

Proceedings of the two day national workshop on advanced materials for engineering applications

International Nuclear Information System (INIS)

John Alexis, S.; Jayakumar, S.

2012-01-01

The subjects like material preparation, material forming, material properties, materials testing, material mechanics, material structure, metal materials, non-metallic materials, composite materials, medical materials, chemical materials, food materials, electrician/electrical materials, building materials, biological materials, electronic/magnetic/optical materials, advanced materials applications in engineering are included in the workshop. Processing of advanced materials, studies on novel ceramic coatings, high strength, light weight and nanostructured materials are discussed in this proceedings. Papers relevant to INIS are indexed separately

AML (Advanced Mud Logging: First Among Equals

Directory of Open Access Journals (Sweden)

T. Loermans

2017-09-01

Full Text Available During the past ten years an enormous development in mud logging technology has been made. Traditional mud logging was only qualitative in nature, and mudlogs could not be used for the petrophysical well evaluations which form the basis for all subsequent activities on wells and fields. AML however can provide quantitative information, logs with a reliability, trueness and precision like LWD and WLL. Hence for well evaluation programmes there are now three different logging methods available, each with its own pros and cons on specific aspects: AML, LWD and WLL. The largest improvements have been made in mud gas analysis and elemental analysis of cuttings. Mud gas analysis can yield hydrocarbon fluid composition for some components with a quality like PVT analysis, hence not only revolutionising the sampling programme so far done with only LWD/WLL, but also making it possible to geosteer on fluid properties. Elemental analysis of cuttings, e.g. with XRF, with an ability well beyond the capabilities of the spectroscopy measurements possible earlier with LWD/WLL tools, is opening up improved ways to evaluate formations, especially of course where the traditional methods are falling short of requirements, such as in unconventional reservoirs. An overview and specific examples of these AML logs is given, from which it may be concluded that AML now ought to be considered as “first among its equals”.

2014 National Workshop on Advances in Communication and Computing

CERN Document Server

Prasanna, S; Sarma, Kandarpa; Saikia, Navajit

2015-01-01

The present volume is a compilation of research work in computation, communication, vision sciences, device design, fabrication, upcoming materials and related process design, etc. It is derived out of selected manuscripts submitted to the 2014 National Workshop on Advances in Communication and Computing (WACC 2014), Assam Engineering College, Guwahati, Assam, India which is emerging out to be a premier platform for discussion and dissemination of knowhow in this part of the world. The papers included in the volume are indicative of the recent thrust in computation, communications and emerging technologies. Certain recent advances in ZnO nanostructures for alternate energy generation provide emerging insights into an area that has promises for the energy sector including conservation and green technology. Similarly, scholarly contributions have focused on malware detection and related issues. Several contributions have focused on biomedical aspects including contributions related to cancer detection using act...

2. JAPAN-IAEA workshop on advanced safeguards technology for the future nuclear fuel cycle. Abstracts

International Nuclear Information System (INIS)

2009-01-01

This international workshop addressed issues and technologies associated with safeguarding the future nuclear fuel cycle. The workshop discussed issues of interest to the safeguards community, facility operators and State Systems of accounting and control of nuclear materials. Topic areas covered were as follows: Current Status and Future Prospects of Developing Safeguards Technologies for Nuclear Fuel Cycle Facilities, Technology and Instrumentation Needs, Advanced Safeguards Technologies, Guidelines on Developing Instrumentation to Lead the Way for Implementing Future Safeguards, and Experiences and Lessons learned. This workshop was of interest to individuals and organizations concerned with future nuclear fuel cycle technical developments and safeguards technologies. This includes representatives from the nuclear industry, R and D organizations, safeguards inspectorates, State systems of accountancy and control, and Member States Support Programmes

International Advanced Robotics Programme. First workshop on manipulators, sensors and steps towards mobility

International Nuclear Information System (INIS)

Martin, T.

1987-09-01

This Workshop was held within the framework of the international collaboration in the area of advanced robotics, formerly initiated by the Economic Summit, called the International Advanced Robotics Programme (IARP). It was hosted by the Nuclear Research Center Karlsruhe on May 11-13, 1987. Ninety scientists of eight countries presented and discussed 32 R+D projects. The Proceedings contain full papers of most contributions (and summaries of the remaining ones) and summary reports on all of the eight sessions. The material presented reflects well the present endeavor to integrate advanced robotics and teleoperation techniques for difficult applications in harsh, demanding or dangerous conditions or environment. (orig.) [de

Report of the Advanced Neutron Source (ANS) safety workshop, Knoxville, Tennessee, October 25--26, 1988

International Nuclear Information System (INIS)

Buchanan, J.R.; Dumont, J.N.; Kendrick, C.M.; Row, T.H.; Thompson, P.B.; West, C.D.; Marchaterre, J.F.; Muhlheim, M.D.; McBee, M.R.

1988-12-01

On October 25--26, 1988, about 60 people took part in an Advanced Neutron Source (ANS) Safety Workshop, organized in cooperation with the Oak Ridge Operations (ORO) Office of the Department of Energy (DOE) and held in Knoxville, Tennessee. After a plenary session at which ANS Project staff presented status reports on the ANS design, research and development (R and D), and safety analysis efforts, the workshop broke into three working groups, each covering a different topic: Environmental and Waste Management, Applicable Regulatory Safety Criteria and Goals, and Reactor Concepts. Each group was asked to review the Project's approach to safety-related issues and to provide guidance on future reactor safety needs or directions for the Project. With the help of able chairmen, assisted by reporters and secretarial support, the working groups were extremely successful. Draft reports from each group were prepared before the workshop closed, and the major findings of each group were presented for review and discussion by the entire workshop attendance. This report contains the final version of the group reports, incorporating the results of the overall review by all the workshop participants

Third advanced research workshop: Gravity, astrophysics and strings at the Black Sea. Proceedings

International Nuclear Information System (INIS)

Fiziev, P.; Todorov, M.

2006-01-01

The Third Advanced Workshop ‘Gravity, Astrophysics, and Strings’ held on 13-20 June 2005. The workshop: 1) Bringing together scientists from various branches of gravitational physics, astrophysics, particle physics, fundamental interactions and string theory gave an opportunity for interdisciplinary exchange of views and enhanced possible collaborations; 2) Provided a unique opportunity to scientists from various countries to communicate with colleagues on the hottest topics of gravitational physics, astrophysics, particle physics, fundamental interactions and string theory; 3) Opened new venue to young talented scientists to communicate and work with major research groups on the topics of the conference; 4) Stimulated creation of a new generation of young physicists for further development of the above basic topics in fundamental science. The workshop covered wide aspects of gravitational physics, astrophysics, particle physics, fundamental interactions and string theory concerning the topics: Astrophysics; Mathematical Modeling and Numerical Simulations in Relativity; Relativistic Gravity; Particle Physics and Fundamental Interactions; (Super)Strings. About 40 participants from Europe, America and Asia gave 32 invited talks and contributed presentations. They and guided general discussion as well, which took place confirmed the considerable interest to the themes of the workshop. The full text of 22 of the presented papers are included in this book

Radiation Source Replacement Workshop

Energy Technology Data Exchange (ETDEWEB)

Griffin, Jeffrey W.; Moran, Traci L.; Bond, Leonard J.

2010-12-01

This report summarizes a Radiation Source Replacement Workshop in Houston Texas on October 27-28, 2010, which provided a forum for industry and researchers to exchange information and to discuss the issues relating to replacement of AmBe, and potentially other isotope sources used in well logging.

NATO Advanced Research Workshop, 19-22 May 1997: Rapid Method for Monitoring the Environment for Biological Hazards

National Research Council Canada - National Science Library

1997-01-01

The NATO Advanced Research Workshop met for the purpose of bringing to light rapid methods for monitoring the environment for biological hazards such as biological warfare agents, naturally occurring...

Cross-system log file analysis for hypothesis testing

NARCIS (Netherlands)

Glahn, Christian; Specht, Marcus; Schoonenboom, Judith; Sligte, Henk; Moghnieh, Ayman; Hernández-Leo, Davinia; Stefanov, Krassen; Lemmers, Ruud; Koper, Rob

2008-01-01

Glahn, C., Specht, M., Schoonenboom, J., Sligte, H., Moghnieh, A., Hernández-Leo, D. Stefanov, K., Lemmers, R., & Koper, R. (2008). Cross-system log file analysis for hypothesis testing. In H. Sligte & R. Koper (Eds.), Proceedings of the 4th TENCompetence Open Workshop. Empowering Learners for

NATO Advanced Research Workshop on Methods and Mechanisms for Producing Ions from Large Molecules

CERN Document Server

Ens, Werner

1991-01-01

A NATO Advanced Research Workshop on Methods and Mechanisms for Producing Ions from Large Molecules was held at Minaki Lodge, Minaki, Ontario, Canada, from 24 to 28 June 1990. The workshop was hosted by the time-of-flight group of the Department of Physics at the University of Manitoba, and was attended by 64 invited participants from around the world. Twenty-nine invited talks were given and 19 papers were presented as posters. Of the 48 contributions, 38 are included in these proceedings. The conference was organized to study the rapidly changing field of mass spectrometry of biomolecules. Particle-induced desorption (especially with MeV particles) has been the most effective method of producing molecular ions from biomolecules. An important part of the workshop was devoted to recent developments in this field, particularly to progress in understanding the fundamentals of the desorption process. In this respect, the meeting was similar to previous conferences in Marburg, FRG (1978); Paris, F (1980); Uppsala...

23rd workshop on Advances in Analog Circuit Design

CERN Document Server

Baschirotto, Andrea; Makinwa, Kofi

2015-01-01

This book is based on the 18 tutorials presented during the 23rd workshop on Advances in Analog Circuit Design.  Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, serving as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.    • Includes coverage of high-performance analog-to-digital and digital to analog converters, integrated circuit design in scaled technologies, and time-domain signal processing; • Provides a state-of-the-art reference in analog circuit design, written by experts from industry and academia; • Presents material in a tutorial-based format.

NATO Advanced Research Workshop on Zinc Oxide as a Material for Micro- and Optoelectronic Applications

CERN Document Server

Nickel, Norbert H

2005-01-01

This volume reviews the latest experimental and theoretical studies in the field of ZnO. The chapters reflect the topics that were discussed during the NATO Advanced Research Workshop, which brought together researchers from Nato countries, Russia, Ukraine, and Kazakhstan to encourage cross fertilization and wider dissemination of the advances in this important research field. Fundamental issues such as growth of ZnO, structural, optical and electric properties, the role of the hydrogen and more were discussed.

Advanced research workshop: nuclear materials safety

International Nuclear Information System (INIS)

Jardine, L J; Moshkov, M M.

1999-01-01

The Advanced Research Workshop (ARW) on Nuclear Materials Safety held June 8-10, 1998, in St. Petersburg, Russia, was attended by 27 Russian experts from 14 different Russian organizations, seven European experts from six different organizations, and 14 U.S. experts from seven different organizations. The ARW was conducted at the State Education Center (SEC), a former Minatom nuclear training center in St. Petersburg. Thirty-three technical presentations were made using simultaneous translations. These presentations are reprinted in this volume as a formal ARW Proceedings in the NATO Science Series. The representative technical papers contained here cover nuclear material safety topics on the storage and disposition of excess plutonium and high enriched uranium (HEU) fissile materials, including vitrification, mixed oxide (MOX) fuel fabrication, plutonium ceramics, reprocessing, geologic disposal, transportation, and Russian regulatory processes. This ARW completed discussions by experts of the nuclear materials safety topics that were not covered in the previous, companion ARW on Nuclear Materials Safety held in Amarillo, Texas, in March 1997. These two workshops, when viewed together as a set, have addressed most nuclear material aspects of the storage and disposition operations required for excess HEU and plutonium. As a result, specific experts in nuclear materials safety have been identified, know each other from their participation in t he two ARW interactions, and have developed a partial consensus and dialogue on the most urgent nuclear materials safety topics to be addressed in a formal bilateral program on t he subject. A strong basis now exists for maintaining and developing a continuing dialogue between Russian, European, and U.S. experts in nuclear materials safety that will improve the safety of future nuclear materials operations in all the countries involved because of t he positive synergistic effects of focusing these diverse backgrounds of

Organization of the 17th Advanced Accelerator Concepts (AAC16) Workshop by the IEEE. Final Scientific/Technical Report On AWARD NO. DE-SC0015635

Energy Technology Data Exchange (ETDEWEB)

Sutter, David F. [Inst. of Electrical and Electronics Engineers Inc., Piscataway, NJ (United States)

2017-07-15

The 2016 Workshop on Advanced Accelerator Concepts (AAC) was held at the Gaylord Hotel and Conference Center, National Harbor, Maryland, from July 31 through August 5, 2016. This workshop was the seventeenth in a biennial series that began at Los Alamos National Laboratory in 1982 with a workshop on laser acceleration of particles (see AIP Conf. Proc. 91). AAC16 was organized under the sponsorship of the IEEE Council on Superconductivity with financial support from the U. S. Department of Energy Office of High Energy Physics and the National Science Foundation. The scope of the AAC Workshop has grown since 1982 to encompass a broad range of topics related to advancing accelerator science and technology beyond its current scientific and technical limits and is now an internationally acknowledged forum for interdisciplinary discussions on advanced accelerator and beam physics/technology concepts covering the widest possible range of applications. The Workshop continued the trend of growing worldwide participation, attracting world wide participation. The Workshop had a total of 256 attendees comprising (including the U.S.) representatives from 11 countries representing 65 different institutions. Each day’s schedule began with plenary sessions covering broad, cross disciplinary interests or general tutorial topics as selected by the Program Committee, followed by a break out into more narrowly focused working groups. The Workshop was organized into eight Working Groups each with a published statement of topical focus, scope of discussion and goals. A summary of the Working Group activities and conclusions is included in the American Institute of Physics’ (AIP) Conference Proceedings now available as an on line open source document. It has been a long tradition of the AAC workshops to encourage strong student participation. This is accomplished in part by subsidizing student attendance, done for this work shop by using funds from the DOE and National Science

Second advanced research workshop: Gravity, astrophysics and strings at the Black Sea. Proceedings

International Nuclear Information System (INIS)

Fiziev, P.; Todorov, M.

2005-01-01

The Second Advanced Workshop ‘Gravity, Astrophysics, and Strings’ held on 10-16 June 2004. It served four purposes: 1) Bringing together scientists from various branches of gravitational physics, astrophysics, and string theory gave an opportunity for interdisciplinary exchange of views and enhanced possible collaborations; 2) Provided a unique opportunity to scientists from various countries to communicate with colleagues on the hottest topics of gravitational physics, astrophysics, and string theory; 3) Opened new venue to young talented scientists to communicate and work with major research groups on the topics of the conference; 4) Stimulated creation of a new generation of young physicists for further development of the above basic topics in fundamental science. The workshop covered wide aspects of gravity, astrophysics, and string theory concerning the topics: Astrophysics; Mathematical Modeling and Numerical Simulations in Relativity; Relativistic Gravity; (Super)Strings. About 35 participants from Europe, America and Asia gave 28 invited talks and contributed presentations. They and guided general discussion as well, which took place confirmed the considerable interest to the themes of the workshop. The full text of 16 of the presented papers are included in this book

Women's Advancement in Political Science. A Report on the APSA Workshop on the Advancement of Women in Academic Political Science in the United States (Washington, DC, March 4-5, 2004)

Science.gov (United States)

American Political Science Association (NJ1), 2005

2005-01-01

In March 2004, the National Science Foundation funded a two-day workshop by the American Political Science Association (APSA) on the advancement of women in academic political science in the United States. The workshop was prompted by an alarming stall in the number of women entering the discipline and persisting through early years of faculty…

Lung Cancer Workshop XI: Tobacco-Induced Disease: Advances in Policy, Early Detection and Management.

Science.gov (United States)

Mulshine, James L; Avila, Rick; Yankelevitz, David; Baer, Thomas M; Estépar, Raul San Jose; Ambrose, Laurie Fenton; Aldigé, Carolyn R

2015-05-01

The Prevent Cancer Foundation Lung Cancer Workshop XI: Tobacco-Induced Disease: Advances in Policy, Early Detection and Management was held in New York, NY on May 16 and 17, 2014. The two goals of the Workshop were to define strategies to drive innovation in precompetitive quantitative research on the use of imaging to assess new therapies for management of early lung cancer and to discuss a process to implement a national program to provide high quality computed tomography imaging for lung cancer and other tobacco-induced disease. With the central importance of computed tomography imaging for both early detection and volumetric lung cancer assessment, strategic issues around the development of imaging and ensuring its quality are critical to ensure continued progress against this most lethal cancer.

NATO Advanced Research Workshop on Dynamics of Polyatomic Van der Waals Complexes

CERN Document Server

Janda, Kenneth

1991-01-01

This publication is the Proceedings of the NATO Advanced Research Workshop (ARW) on the Dynamics of Polyatomic Van der Waals Molecules held at the Chateau de Bonas, Castera-Verduzan, France, from August 21 through August 26, 1989. Van der Waals complexes provide important model problems for understanding energy transfer and dissipation. These processes can be described in great detail for Van der Waals complexes, and the insight gained from such studies can be applied to more complicated chemical problems that are not amenable to detailed study. The workshop concentrated on the current questions and future prospects for extend­ ing our highly detailed knowledge of triatomic Van der Waals molecule dynamics to polyatomic molecules and clusters (one molecule surrounded by several, or up to sev­ eral tens of, atoms). Both experimental and theoretical studies were discussed, with particular emphasis on the dynamical behavior of dissociation as observed in the dis­ tributions of quantum states of the dissociatio...

First advanced research workshop: Gravity, astrophysics and strings at the Black Sea. Proceedings

International Nuclear Information System (INIS)

Fiziev, P.; Todorov, M.

2002-01-01

The aim of the First Advanced Workshop ‘Gravity, Astrophysics, and Strings’ was: 1)Bringing together scientists from various branches of gravitational physics, astrophysics and string theory gave an opportunity for interdisciplinary exchange of views and enhanced possible collaborations; 2)Provided a unique opportunity to scientists from various countries to communicate with colleagues on the hottest topics of gravitational physics, astrophysics, and string theory; 3) Opened new venue to young talented scientists to communicate and work with major research groups on the topics of the conference. The workshop covered wide aspects of gravity, astrophysics, and string theory concerning the topics: Astrophysics; Mathematical Modeling and Numerical Simulations in Relativity; Astrophysics, and Strings; Relativistic Gravity; (Super)Strings. About 40 participants from Europe, America and Asia gave 30 invited talks and contributed presentations. The full text of 17 of them are included in this book

Advanced Grid Control Technologies Workshop Series | Energy Systems

Science.gov (United States)

: Smart Grid and Beyond John McDonald, Director, Technical Strategy and Policy Development, General Control Technologies Workshop Series In July 2015, NREL's energy systems integration team hosted workshops the Energy Systems Integration Facility (ESIF) and included a technology showcase featuring projects

A transdisciplinary approach to developing a web-based nursing experiential log system for advanced practice nursing clinical experiences.

Science.gov (United States)

Olson, Brandon D; Fauchald, Sally K

2011-11-01

This article describes a transdisciplinary project between the computer information systems department and the graduate nursing department of a higher education institution. The project is the planning, development, and implementation of a Web-based nursing experiential log system for advanced practice nursing clinical experiences, which was funded by a Nursing Education Practice and Retention grant from the Health Resources and Services Administration. The article explains the concept and benefits of the transdisciplinary nature of the project. The design team, project leadership, and roles within the team are reviewed, including the role of end-user faculty in the design process. The article describes the focus and scope of the Web-based experiential log system database that is used to document and track advanced practice nursing student clinical experiences, as well as a summary of the design process used to develop the log system and the specific functionality of the database system. The implementation process, including end-user training, pilot implementation, and modifications, lessons learned, and future directions of the project are addressed. The article concludes with the benefits to the clinical experience and graduate nursing program that have been noted since the implementation of the system.

NATO Advanced Research Workshop on The Biogeochemical Cycling of Sulfur and Nitrogen in the Remote Atmosphere

CERN Document Server

Charlson, Robert; Andreae, Meinrat; Rodhe, Henning

1985-01-01

Viewed from space, the Earth appears as a globe without a beginning or an end. Encompassing the globe is the atmosphere with its three phases-­ gaseous, liquid, and solid--moving in directions influenced by sunlight, gravity, and rotation. The chemical compositions of these phases are determined by biogeochemical cycles. Over the past hundred years, the processes governing the rates and reactions in the atmospheric biogeochemical cycles have typically been studied in regions where scientists lived. Hence, as time has gone by, the advances in our knowledge of atmospheric chemical cycles in remote areas have lagged substantially behind those for more populated areas. Not only are the data less abundant, they are also scattered. Therefore, we felt a workshop would be an excellent mechanism to assess the state­ of-knowledge of the atmospheric cycles of sulfur and nitrogen in remote areas and to make recommendations for future research. Thus, a NATO Advanced Research Workshop '~he Biogeochemical Cycling of Sulfu...

NATO Advanced Research Workshop on Time-Dependent Quantum Molecular Dynamics : Theory and Experiment

CERN Document Server

Lathouwers, L

1992-01-01

From March 30th to April 3rd, 1992, a NATO Advanced Research workshop entitled "Time Dependent Quantum Molecular Dynamics: Theory and Experiment" was held at Snowbird, Utah. The organizing committee consisted of J. BROECKHOVE (Antwerp, Belgium), L. CEDERBAUM (Heidelberg, Germany), L. LATHOUWERS (Antwerp, Belgium), N. OHRN (Gainesville, Florida) and J. SIMONS (Salt Lake City, Utah). Fifty-two participants from eleven different countries attended the meeting at which thirty-three talks and one poster session were held. Twenty-eight participants submitted contributions to the proceedings of the meeting, which are reproduced in this volume. The workshop brought together experts in different areas 0 f molecular quantum dynamics, all adhering to the time dependent approach. The aim was to discuss and compare methods and applications. The ~amiliarityo~ the aUdience with the concepts o~ time dependent approaches greatly facilitated topical discussions and probing towards new applications. A broad area of subject matt...

Well log characterization of natural gas-hydrates

Science.gov (United States)

Collett, Timothy S.; Lee, Myung W.

2012-01-01

In the last 25 years there have been significant advancements in the use of well-logging tools to acquire detailed information on the occurrence of gas hydrates in nature: whereas wireline electrical resistivity and acoustic logs were formerly used to identify gas-hydrate occurrences in wells drilled in Arctic permafrost environments, more advanced wireline and logging-while-drilling (LWD) tools are now routinely used to examine the petrophysical nature of gas-hydrate reservoirs and the distribution and concentration of gas hydrates within various complex reservoir systems. Resistivity- and acoustic-logging tools are the most widely used for estimating the gas-hydrate content (i.e., reservoir saturations) in various sediment types and geologic settings. Recent integrated sediment coring and well-log studies have confirmed that electrical-resistivity and acoustic-velocity data can yield accurate gas-hydrate saturations in sediment grain-supported (isotropic) systems such as sand reservoirs, but more advanced log-analysis models are required to characterize gas hydrate in fractured (anisotropic) reservoir systems. New well-logging tools designed to make directionally oriented acoustic and propagation-resistivity log measurements provide the data needed to analyze the acoustic and electrical anisotropic properties of both highly interbedded and fracture-dominated gas-hydrate reservoirs. Advancements in nuclear magnetic resonance (NMR) logging and wireline formation testing (WFT) also allow for the characterization of gas hydrate at the pore scale. Integrated NMR and formation testing studies from northern Canada and Alaska have yielded valuable insight into how gas hydrates are physically distributed in sediments and the occurrence and nature of pore fluids(i.e., free water along with clay- and capillary-bound water) in gas-hydrate-bearing reservoirs. Information on the distribution of gas hydrate at the pore scale has provided invaluable insight on the mechanisms

Proceedings of the NATO Advanced Research Workshop on Nuclear Power and Energy Security

International Nuclear Information System (INIS)

Apikyan, S.; Diamond, D.

2010-01-01

The purpose of this NATO workshop is to contribute to the critical assessment of how to prepare for a new national nuclear energy program, and to make recommendations for future action. In addition, our goal is to promote close working relationships between technical people from different countries and with different professional expertise. In particular, the countries that are involved in this workshop are those from NATO and those from the Partner countries such as those in the Commonwealth of Independent States. A NATO workshop is not an international conference or symposium but rather a forum for advanced level, intensive discussions. The presentations are part of the growing font of knowledge on the subject of how to develop a national nuclear energy program. It is heard about the infrastructure that is needed and how the IAEA and countries with existing experience are helping to provide that infrastructure to those working toward a nuclear energy program. It is heard about the experiences of several countries embarking on new nuclear development, with an emphasis on how progress is being made in Armenia. It is also heard about the potential for using small and medium size reactors; something not being pursued by the countries with large nuclear programs

MO-AB-210-03: Workshop [Advancements in high intensity focused ultrasound

Energy Technology Data Exchange (ETDEWEB)

Lu, Z. [University of Chicago (United States)

2015-06-15

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

PREFACE: APCTP-ASEAN Workshop on Advanced Materials Science and Nanotechnology (AMSN08)

Science.gov (United States)

Van Hieu, Nguyen

2009-09-01

Dear friends To contribute to the enhancement of the international scientific cooperation of the ASEAN countries and in reply to the proposal of the Vietnam Academy of Science and Technology (VAST), the Asia-Pacific Center for Theoretical Physics (APCTP) and the Sub Committee on Materials Science and Technology (SCMST) of the ASEAN Committee of Science and Technology (ASEAN COST) agreed to organize this APCTP-ASEAN Workshop on Advanced Materials Science and Nanotechnology with the participation of the Ministry of Science and Technology of Vietnam, the Vietnam Academy of Science and Technology, Rencontres du Vietnam, the Vietnam Physical Society, the Vietnam National University in Ho Chi Minh City and the Vietnam National University in Hanoi. As well as the participants from 9 of the 10 ASEAN countries and many other countries/regions of APCTP (Australia, China, Chinese Taipei, Japan and Korea) we warmly welcome the guests from Europe, the United States, Canada and Israel. Without the financial support of the Asia-Pacific Center for Theoretical Physics APCTP, Abdus Salam International Center for Theoretical Physics ICTP, the Asian Office of Aerospace Research and Development AOARD, the US Office of Naval Research Global-Asia ONRG, the Ministry of Science and Technology of Vietnam MOST, the Vietnam Academy of Science and Technology VAST, the Vietnam National University in Ho Chi Minh City VNU HCMC and other Sponsors, we would have been unable to hold this Workshop. On behalf of the International and Local Organizing Committees I would like to express our deep gratitude to the Sponsors. We highly appreciate the support and advice of the members of the International Advisory Committee, the scientific contribution of the invited speakers and all participants. We acknowledge the warm reception of the Khanh Hoa province Administration and citizens, and the hard work of the VAST staff for the success of the Workshop. We cordially wish all participants lively scientific

Proceedings of the 18th Advanced ICFA Beam Dynamics Workshop on Quantum Aspects of Beam Physics (QABP)

International Nuclear Information System (INIS)

Chen, Pisin

2002-01-01

The 18th Advanced ICFA Beam Dynamics Workshop on ''Quantum Aspects of Beam Physics'' was held from October 15 to 20, 2000, in Capri, Italy. This was the second workshop under the same title. The first one was held in Monterey, California, in January, 1998. Following the footstep of the first meeting, the second one in Capri was again a tremendous success, both scientifically and socially. About 70 colleagues from astrophysics, atomic physics, beam physics, condensed matter physics, particle physics, and general relativity gathered to update and further explore the topics covered in the Monterey workshop. Namely, the following topics were actively discussed: (1) Quantum Fluctuations in Beam Dynamics; (2) Photon-Electron Interaction in Beam handling; (3) Physics of Condensed Beams; (4) Beam Phenomena under Strong Fields; (5) Quantum Methodologies in Beam Physics. In addition, there was a newly introduced subject on Astro-Beam Physics and Laboratory Astrophysics

AAAI Workshop on Nonmonotonic Reasoning

OpenAIRE

Etherington, David

1985-01-01

On October 17-19 1984 a workshop on non-monotonic reasoning was held at Mohonk Mountain House, outside New Paltz, New York. The workshop was organized by Raymond Reiter and Bonnie Webber, and was sponsored by the Association for the Advancement of Artificial Intelligence.

Alternate fusion fuels workshop

International Nuclear Information System (INIS)

1981-06-01

The workshop was organized to focus on a specific confinement scheme: the tokamak. The workshop was divided into two parts: systems and physics. The topics discussed in the systems session were narrowly focused on systems and engineering considerations in the tokamak geometry. The workshop participants reviewed the status of system studies, trade-offs between d-t and d-d based reactors and engineering problems associated with the design of a high-temperature, high-field reactor utilizing advanced fuels. In the physics session issues were discussed dealing with high-beta stability, synchrotron losses and transport in alternate fuel systems. The agenda for the workshop is attached

22nd Workshop on Advances in Analog Circuit Design

CERN Document Server

Makinwa, Kofi; Harpe, Pieter

2014-01-01

This book is based on the 18 tutorials presented during the 22nd workshop on Advances in Analog Circuit Design.  Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, including frequency reference, power management for systems-on-chip, and smart wireless interfaces.  This book serves as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.    ·         Provides a state-of-the-art reference in analog circuit design, written by experts from industry and academia; ·         Presents material in a tutorial-based format; ·         Includes coverage of frequency reference, power management for systems-on-chip, and smart wireless interfaces.

NATO Advanced Research Workshop on Frontiers in Polymerization Catalysis and Polymer Synthesis

CERN Document Server

Guyot, A

1987-01-01

Due to their specific properties, polymers with well-defined structures have been receiving increasing attention over the last several years. Owing to the wide variability of their properties, these specialty polymers have been used in various areas from biomedical engineering to electronics or energy applications. The synthesis of such polymers necessi­ tates the use of new methods of polymerization which derived from an insight into the mechanism of polymerization reactions. A NATO Advanced Research Workshop on "Frontiers in Polymerization Catalysis and Polymer Synthesis" was held in BANDOl (FRANCE) in February 1987. Its aim was to assess the new polymerization methods, as well as the latest advances in the mechanisms of conventional polymerization reactions together with their applications to the synthesis of new macromolecular structures. The financial support from the NATO Scientific Affairs Division which covered the "lecturers' accomodation and travel expenses as well as the organization charges of th...

NASA Laser Light Scattering Advanced Technology Development Workshop, 1988

Science.gov (United States)

Meyer, William V. (Editor)

1989-01-01

The major objective of the workshop was to explore the capabilities of existing and prospective laser light scattering hardware and to assess user requirements and needs for a laser light scattering instrument in a reduced gravity environment. The workshop addressed experimental needs and stressed hardware development.

17th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT 2016)

International Nuclear Information System (INIS)

2016-01-01

Preface The 2016 version of the International Workshop on Advanced Computing and Analysis Techniques in Physics Research took place on January 18-22, 2016, at the Universidad Técnica Federico Santa Maria -UTFSM- in Valparaiso, Chile. The present volume of IOP Conference Series is devoted to the selected scientific contributions presented at the workshop. In order to guarantee the scientific quality of the Proceedings all papers were thoroughly peer-reviewed by an ad-hoc Editorial Committee with the help of many careful reviewers. The ACAT Workshop series has a long tradition starting in 1990 (Lyon, France), and takes place in intervals of a year and a half. Formerly these workshops were known under the name AIHENP (Artificial Intelligence for High Energy and Nuclear Physics). Each edition brings together experimental and theoretical physicists and computer scientists/experts, from particle and nuclear physics, astronomy and astrophysics in order to exchange knowledge and experience in computing and data analysis in physics. Three tracks cover the main topics: Computing technology: languages and system architectures. Data analysis: algorithms and tools. Theoretical Physics: techniques and methods. Although most contributions and discussions are related to particle physics and computing, other fields like condensed matter physics, earth physics, biophysics are often addressed in the hope to share our approaches and visions. It created a forum for exchanging ideas among fields, exploring and promoting cutting-edge computing technologies and debating hot topics. (paper)

Log-Log Convexity of Type-Token Growth in Zipf's Systems

Science.gov (United States)

Font-Clos, Francesc; Corral, Álvaro

2015-06-01

It is traditionally assumed that Zipf's law implies the power-law growth of the number of different elements with the total number of elements in a system—the so-called Heaps' law. We show that a careful definition of Zipf's law leads to the violation of Heaps' law in random systems, with growth curves that have a convex shape in log-log scale. These curves fulfill universal data collapse that only depends on the value of Zipf's exponent. We observe that real books behave very much in the same way as random systems, despite the presence of burstiness in word occurrence. We advance an explanation for this unexpected correspondence.

PREFACE: 14th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT 2011)

Science.gov (United States)

Teodorescu, Liliana; Britton, David; Glover, Nigel; Heinrich, Gudrun; Lauret, Jérôme; Naumann, Axel; Speer, Thomas; Teixeira-Dias, Pedro

2012-06-01

ACAT2011 This volume of Journal of Physics: Conference Series is dedicated to scientific contributions presented at the 14th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT 2011) which took place on 5-7 September 2011 at Brunel University, UK. The workshop series, which began in 1990 in Lyon, France, brings together computer science researchers and practitioners, and researchers from particle physics and related fields in order to explore and confront the boundaries of computing and of automatic data analysis and theoretical calculation techniques. It is a forum for the exchange of ideas among the fields, exploring and promoting cutting-edge computing, data analysis and theoretical calculation techniques in fundamental physics research. This year's edition of the workshop brought together over 100 participants from all over the world. 14 invited speakers presented key topics on computing ecosystems, cloud computing, multivariate data analysis, symbolic and automatic theoretical calculations as well as computing and data analysis challenges in astrophysics, bioinformatics and musicology. Over 80 other talks and posters presented state-of-the art developments in the areas of the workshop's three tracks: Computing Technologies, Data Analysis Algorithms and Tools, and Computational Techniques in Theoretical Physics. Panel and round table discussions on data management and multivariate data analysis uncovered new ideas and collaboration opportunities in the respective areas. This edition of ACAT was generously sponsored by the Science and Technology Facility Council (STFC), the Institute for Particle Physics Phenomenology (IPPP) at Durham University, Brookhaven National Laboratory in the USA and Dell. We would like to thank all the participants of the workshop for the high level of their scientific contributions and for the enthusiastic participation in all its activities which were, ultimately, the key factors in the

PREFACE: 16th International workshop on Advanced Computing and Analysis Techniques in physics research (ACAT2014)

Science.gov (United States)

Fiala, L.; Lokajicek, M.; Tumova, N.

2015-05-01

This volume of the IOP Conference Series is dedicated to scientific contributions presented at the 16th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT 2014), this year the motto was ''bridging disciplines''. The conference took place on September 1-5, 2014, at the Faculty of Civil Engineering, Czech Technical University in Prague, Czech Republic. The 16th edition of ACAT explored the boundaries of computing system architectures, data analysis algorithmics, automatic calculations, and theoretical calculation technologies. It provided a forum for confronting and exchanging ideas among these fields, where new approaches in computing technologies for scientific research were explored and promoted. This year's edition of the workshop brought together over 140 participants from all over the world. The workshop's 16 invited speakers presented key topics on advanced computing and analysis techniques in physics. During the workshop, 60 talks and 40 posters were presented in three tracks: Computing Technology for Physics Research, Data Analysis - Algorithms and Tools, and Computations in Theoretical Physics: Techniques and Methods. The round table enabled discussions on expanding software, knowledge sharing and scientific collaboration in the respective areas. ACAT 2014 was generously sponsored by Western Digital, Brookhaven National Laboratory, Hewlett Packard, DataDirect Networks, M Computers, Bright Computing, Huawei and PDV-Systemhaus. Special appreciations go to the track liaisons Lorenzo Moneta, Axel Naumann and Grigory Rubtsov for their work on the scientific program and the publication preparation. ACAT's IACC would also like to express its gratitude to all referees for their work on making sure the contributions are published in the proceedings. Our thanks extend to the conference liaisons Andrei Kataev and Jerome Lauret who worked with the local contacts and made this conference possible as well as to the program

Advanced Training Technologies and Learning Environments

Science.gov (United States)

Noor, Ahmed K. (Compiler); Malone, John B. (Compiler)

1999-01-01

This document contains the proceedings of the Workshop on Advanced Training Technologies and Learning Environments held at NASA Langley Research Center, Hampton, Virginia, March 9-10, 1999. The workshop was jointly sponsored by the University of Virginia's Center for Advanced Computational Technology and NASA. Workshop attendees were from NASA, other government agencies, industry, and universities. The objective of the workshop was to assess the status and effectiveness of different advanced training technologies and learning environments.

Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Products Successfully to the Market - Report from the CAT-DGTI-GSCN Workshop at the DGTI Annual Meeting 2014.

Science.gov (United States)

Celis, Patrick; Ferry, Nicolas; Hystad, Marit; Schüßler-Lenz, Martina; Doevendans, Pieter A; Flory, Egbert; Beuneu, Claire; Reischl, Ilona; Salmikangas, Paula

2015-05-01

On September 11, 2014, a workshop entitled 'Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Product Successfully to the Market' was held at the 47th annual meeting of the German Society for Transfusion Medicine and Immunohematology (DGTI), co-organised by the European Medicines Agency (EMA) and the DGTI in collaboration with the German Stem Cell Network (GSCN). The workshop brought together over 160 participants from academia, hospitals, small- or medium-sized enterprise developers and regulators. At the workshop, speakers from EMA, the Committee for Advanced Therapies (CAT), industry and academia addressed the regulatory aspects of development and authorisation of advanced therapy medicinal products (ATMPs), classification of ATMPs and considerations on cell-based therapies for cardiac repair. The open forum discussion session allowed for a direct interaction between ATMP developers and the speakers from EMA and CAT.

PREFACE: Joint IPPP Durham/Cockcroft Institute/ICFA Workshop on Advanced QED methods for Future Accelerators

Science.gov (United States)

Bailey, I. R.; Barber, D. P.; Chattopadhyay, S.; Hartin, A.; Heinzl, T.; Hesselbach, S.; Moortgat-Pick, G. A.

2009-11-01

The joint IPPP Durham/Cockcroft Institute/ICFA workshop on advanced QED methods for future accelerators took place at the Cockcroft Institute in early March 2009. The motivation for the workshop was the need for a detailed consideration of the physics processes associated with beam-beam effects at the interaction points of future high-energy electron-positron colliders. There is a broad consensus within the particle physics community that the next international facility for experimental high-energy physics research beyond the Large Hadron Collider at CERN should be a high-luminosity electron-positron collider working at the TeV energy scale. One important feature of such a collider will be its ability to deliver polarised beams to the interaction point and to provide accurate measurements of the polarisation state during physics collisions. The physics collisions take place in very dense charge bunches in the presence of extremely strong electromagnetic fields of field strength of order of the Schwinger critical field strength of 4.4×1013 Gauss. These intense fields lead to depolarisation processes which need to be thoroughly understood in order to reduce uncertainty in the polarisation state at collision. To that end, this workshop reviewed the formalisms for describing radiative processes and the methods of calculation in the future strong-field environments. These calculations are based on the Furry picture of organising the interaction term of the Lagrangian. The means of deriving the transition probability of the most important of the beam-beam processes - Beamsstrahlung - was reviewed. The workshop was honoured by the presentations of one of the founders, V N Baier, of the 'Operator method' - one means for performing these calculations. Other theoretical methods of performing calculations in the Furry picture, namely those due to A I Nikishov, V I Ritus et al, were reviewed and intense field quantum processes in fields of different form - namely those

FINPIE/97. Workshop proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This publication contains the proceedings of 1997 Finnish Workshop on Power and Industrial Electronics, held in Espoo, Finland, on 26 August, 1997. The programme consisted of technical sessions on Advanced AC Motor Control, Electric Machines and Drives, Advanced Control and Measurement, Power Electronics Systems, Modelling and Simulation, and Power Converters

Advanced Research Workshop on Preparedness for Nuclear and Radiological Threats

CERN Document Server

Diamond, David; Nuclear Threats and Security Challenges

2015-01-01

With the dissolution of the Soviet Union the nuclear threats facing the world are constantly evolving and have grown more complex since the end of the Cold War. The diversion of complete weapon systems or nuclear material to rogue nations and terrorist organizations has increased. The events of the past years have proved the necessity to reevaluate these threats on a level never before considered.  In recognition that no single country possesses all of the answers to the critical scientific, institutional and legal questions associated with combating nuclear and radiological terrorism, the NATO Advanced Research Workshop on “Preparedness for Nuclear and Radiological Threats” and this proceeding was structured to promote wide-ranging, multi-national exploration of critical technology needs and underlying scientific challenges to reducing the threat of nuclear/radiological terrorism; to illustrate through country-specific presentations how resulting technologies were used in national programs; and to outli...

National Institutes of Health Pathways to Prevention Workshop: Advancing Research to Prevent Youth Suicide.

Science.gov (United States)

Little, Todd D; Roche, Kathleen M; Chow, Sy-Miin; Schenck, Anna P; Byam, Leslie-Ann

2016-12-06

The National Institutes of Health (NIH) Pathways to Prevention Workshop "Advancing Research to Prevent Youth Suicide" was cosponsored by the NIH Office of Disease Prevention, National Institute of Mental Health, National Institute on Drug Abuse, and National Center for Complementary and Integrative Health. A multidisciplinary working group developed the agenda, and an evidence-based practice center prepared an evidence report that addressed data systems relevant to suicide prevention efforts through a contract with the Agency for Healthcare Research and Quality. During the workshop, experts discussed the evidence and participants commented during open forums. After considering the data from the evidence report, expert presentations, and public comments, an independent panel prepared a draft report that was posted on the NIH Office of Disease Prevention Web site for 5 weeks for public comment. This abridged version of the final report provides a road map for optimizing youth suicide prevention efforts by highlighting strategies for guiding the next decade of research in this area. These strategies include recommendations for improving data systems, enhancing data collection and analysis methods, and strengthening the research and practice community.

Anomaly Detection in Log Data using Graph Databases and Machine Learning to Defend Advanced Persistent Threats

OpenAIRE

Schindler, Timo

2018-01-01

Advanced Persistent Threats (APTs) are a main impendence in cyber security of computer networks. In 2015, a successful breach remains undetected 146 days on average, reported by [Fi16].With our work we demonstrate a feasible and fast way to analyse real world log data to detect breaches or breach attempts. By adapting well-known kill chain mechanisms and a combine of a time series database and an abstracted graph approach, it is possible to create flexible attack profiles. Using this approach...

Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Products Successfully to the Market – Report from the CAT-DGTI-GSCN Workshop at the DGTI Annual Meeting 2014

Science.gov (United States)

Celis, Patrick; Ferry, Nicolas; Hystad, Marit; Schüßler-Lenz, Martina; Doevendans, Pieter A.; Flory, Egbert; Beuneu, Claire; Reischl, Ilona; Salmikangas, Paula

2015-01-01

On September 11, 2014, a workshop entitled ‘Advanced Therapy Medicinal Products: How to Bring Cell-Based Medicinal Product Successfully to the Market’ was held at the 47th annual meeting of the German Society for Transfusion Medicine and Immunohematology (DGTI), co-organised by the European Medicines Agency (EMA) and the DGTI in collaboration with the German Stem Cell Network (GSCN). The workshop brought together over 160 participants from academia, hospitals, small- or medium-sized enterprise developers and regulators. At the workshop, speakers from EMA, the Committee for Advanced Therapies (CAT), industry and academia addressed the regulatory aspects of development and authorisation of advanced therapy medicinal products (ATMPs), classification of ATMPs and considerations on cell-based therapies for cardiac repair. The open forum discussion session allowed for a direct interaction between ATMP developers and the speakers from EMA and CAT. PMID:26195933

PREFACE: 15th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT2013)

Science.gov (United States)

Wang, Jianxiong

2014-06-01

This volume of Journal of Physics: Conference Series is dedicated to scientific contributions presented at the 15th International Workshop on Advanced Computing and Analysis Techniques in Physics Research (ACAT 2013) which took place on 16-21 May 2013 at the Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China. The workshop series brings together computer science researchers and practitioners, and researchers from particle physics and related fields to explore and confront the boundaries of computing and of automatic data analysis and theoretical calculation techniques. This year's edition of the workshop brought together over 120 participants from all over the world. 18 invited speakers presented key topics on the universe in computer, Computing in Earth Sciences, multivariate data analysis, automated computation in Quantum Field Theory as well as computing and data analysis challenges in many fields. Over 70 other talks and posters presented state-of-the-art developments in the areas of the workshop's three tracks: Computing Technologies, Data Analysis Algorithms and Tools, and Computational Techniques in Theoretical Physics. The round table discussions on open-source, knowledge sharing and scientific collaboration stimulate us to think over the issue in the respective areas. ACAT 2013 was generously sponsored by the Chinese Academy of Sciences (CAS), National Natural Science Foundation of China (NFSC), Brookhaven National Laboratory in the USA (BNL), Peking University (PKU), Theoretical Physics Cernter for Science facilities of CAS (TPCSF-CAS) and Sugon. We would like to thank all the participants for their scientific contributions and for the en- thusiastic participation in all its activities of the workshop. Further information on ACAT 2013 can be found at http://acat2013.ihep.ac.cn. Professor Jianxiong Wang Institute of High Energy Physics Chinese Academy of Science Details of committees and sponsors are available in the PDF

Symmetries In Graphs, Maps, And Polytopes Workshop 2014

CERN Document Server

Jajcay, Robert

2016-01-01

This volume contains seventeen of the best papers delivered at the SIGMAP Workshop 2014, representing the most recent advances in the field of symmetries of discrete objects and structures, with a particular emphasis on connections between maps, Riemann surfaces and dessins d’enfant. Providing the global community of researchers in the field with the opportunity to gather, converse and present their newest findings and advances, the Symmetries In Graphs, Maps, and Polytopes Workshop 2014 was the fifth in a series of workshops. The initial workshop, organized by Steve Wilson in Flagstaff, Arizona, in 1998, was followed in 2002 and 2006 by two meetings held in Aveiro, Portugal, organized by Antonio Breda d’Azevedo, and a fourth workshop held in Oaxaca, Mexico, organized by Isabel Hubard in 2010. This book should appeal to both specialists and those seeking a broad overview of what is happening in the area of symmetries of discrete objects and structures.

Risk Management Techniques and Practice Workshop Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Quinn, T; Zosel, M

2008-12-02

At the request of the Department of Energy (DOE) Office of Science (SC), Lawrence Livermore National Laboratory (LLNL) hosted a two-day Risk Management Techniques and Practice (RMTAP) workshop held September 18-19 at the Hotel Nikko in San Francisco. The purpose of the workshop, which was sponsored by the SC/Advanced Scientific Computing Research (ASCR) program and the National Nuclear Security Administration (NNSA)/Advanced Simulation and Computing (ASC) program, was to assess current and emerging techniques, practices, and lessons learned for effectively identifying, understanding, managing, and mitigating the risks associated with acquiring leading-edge computing systems at high-performance computing centers (HPCCs). Representatives from fifteen high-performance computing (HPC) organizations, four HPC vendor partners, and three government agencies attended the workshop. The overall workshop findings were: (1) Standard risk management techniques and tools are in the aggregate applicable to projects at HPCCs and are commonly employed by the HPC community; (2) HPC projects have characteristics that necessitate a tailoring of the standard risk management practices; (3) All HPCC acquisition projects can benefit by employing risk management, but the specific choice of risk management processes and tools is less important to the success of the project; (4) The special relationship between the HPCCs and HPC vendors must be reflected in the risk management strategy; (5) Best practices findings include developing a prioritized risk register with special attention to the top risks, establishing a practice of regular meetings and status updates with the platform partner, supporting regular and open reviews that engage the interests and expertise of a wide range of staff and stakeholders, and documenting and sharing the acquisition/build/deployment experience; and (6) Top risk categories include system scaling issues, request for proposal/contract and acceptance testing, and

Workshop on Critical Issues in Microgravity Fluids, Transport, and Reaction Processes in Advanced Human Support Technology

Science.gov (United States)

Chiaramonte, Francis P.; Joshi, Jitendra A.

2004-01-01

This workshop was designed to bring the experts from the Advanced Human Support Technologies communities together to identify the most pressing and fruitful areas of research where success hinges on collaborative research between the two communities. Thus an effort was made to bring together experts in both advanced human support technologies and microgravity fluids, transport and reaction processes. Expertise was drawn from academia, national laboratories, and the federal government. The intent was to bring about a thorough exchange of ideas and develop recommendations to address the significant open design and operation issues for human support systems that are affected by fluid physics, transport and reaction processes. This report provides a summary of key discussions, findings, and recommendations.

3. IFAC workshop: advances in automotive control. Vol. 1. Preprints

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

As the subject indicates, the aim of this workshop will be to discuss the latest advances related to motor vehicles, but also, and more generally, to exchange ideas between academic partners, car-manufacturers and subcontractors. The programme shows that a special effort has been made in this respect. No doubt plenary lectures are of great importance and the thematic sessions in the different sectors are the essence of such workshops; however, the discussions between experts in the different fields, the meetings between people from industry, universities and public or private laboratories, as well as the resulting exchange of ideas, are at least as important. Research is often criticized for providing merely theoretical results and for the insufficient number of its applications. But the motor vehicle offers a wide field of applications in which we can validate all techniques, tools and methods. This allows us to be involved in all the areas of fundamental research, in all the different possible approaches from fundamental research to technology transfer, and to observe the actual effects of our results. The increase in road traffic was a major problem of the past XXth century. It is clear that one the challenges of the XXIst century will be improve driving safety and comfort. The different work sessions concerning more control, driveline modelling, vehicle dynamics, electronic architecture, intelligent components, engine control, engine modelling, the modelling of combustion and turbocharging, diagnostics and subsystems. The quality of the papers and the diversity of their origins clearly shows the interest that we all take in this key sector of our research and industry. (orig.)

Proceedings of the fifth workshop on containment integrity

Energy Technology Data Exchange (ETDEWEB)

Parks, M.B.; Hughey, C.E. [eds.] [Sandia National Labs., Albuquerque, NM (United States)

1992-07-01

The Fifth Workshop on Containment integrity was held in Washington, DC, on May 12--14, 1992. The purpose of these workshops is to provide an international forum for the exchange of information on performance of containments in nuclear power plants under severe accident loadings. Severe accident investigations of existing containment designs as well as future advanced containments were presented during the workshop. There were 145 participants at the workshop from 15 countries. Individual papers have been cataloged separately.

International cooperation workshop. Regional workshop for CTBTO international cooperation: Africa

International Nuclear Information System (INIS)

1999-08-01

Pursuant to the 1999 programme of work, and following the International Cooperation Workshop held in Vienna, Austria, in 1998, the Provisional Technical Secretariat (PTS) of the Preparatory Commission for the CTBTO (Prep Com) held a regional Workshop for CTBTO International Cooperation in Cairo. The purpose of the workshop was to identify how and by what means the Africa region can promote international cooperation in CTBT verification related technologies, and how the region can benefit from and contribute to Prep Com activity. PTS staff briefed the 40 participants from 22 African States who attended the Workshop on general aspects, including costs, of the establishment and operation of the CTBT verification system, including its four monitoring technologies. Participants were informed on opportunities for local institutions in the establishment of monitoring stations and on possible support for national and regional data centres. National experts presented their research and development activities and reviewed existing experiences on bi/multi-lateral cooperation. The main points of the discussion focused on the need to engage governments to advance signature/ratification, and further training opportunities for African states

Proceedings -- US Russian workshop on fuel cell technologies

Energy Technology Data Exchange (ETDEWEB)

Baker, B.; Sylwester, A. [comps.

1996-04-01

On September 26--28, 1995, Sandia National Laboratories sponsored the first Joint US/Russian Workshop on Fuel Cell Technology at the Marriott Hotel in Albuquerque, New Mexico. This workshop brought together the US and Russian fuel cell communities as represented by users, producers, R and D establishments and government agencies. Customer needs and potential markets in both countries were discussed to establish a customer focus for the workshop. Parallel technical sessions defined research needs and opportunities for collaboration to advance fuel cell technology. A desired outcome of the workshop was the formation of a Russian/American Fuel Cell Consortium to advance fuel cell technology for application in emerging markets in both countries. This consortium is envisioned to involve industry and national labs in both countries. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Proceedings of the Advanced Hadron Facility accelerator design workshop

International Nuclear Information System (INIS)

Thiessen, H.A.

1989-01-01

The International Workshop on Hadron Facility Technology was held February 22-27, 1988, at the Study Center at Los Alamos National Laboratory. The program included papers on facility plans, beam dynamics, and accelerator hardware. The parallel sessions were particularly lively with discussions of all facets of kaon factory design. The workshop provided an opportunity for communication among the staff involved in hadron facility planning from all the study groups presently active. The recommendations of the workshop include: the need to use h=1 RF in the compressor ring; the need to minimize foil hits in painting schemes for all rings; the need to consider single Coulomb scattering in injection beam los calculations; the need to study the effect of field inhomogeneity in the magnets on slow extraction for the 2.2 Tesla main ring of AHF; and agreement in principle with the design proposed for a joint Los Alamos/TRIUMF prototype main ring RF cavity

Report on the Lake Arrowhead workshop on advanced acceleration concepts

International Nuclear Information System (INIS)

Pellegrini, C.

1989-03-01

We review the present status of the field of New Acceleration Concepts, as presented at the Lake Arrowhead workshop, held at the beginning of 1989. Many new and promising results have been obtained recently, and the field is actively developing. We discuss briefly some of the main results presented at the workshop. 43 refs., 2 tabs

Advanced Insider Threat Mitigation Workshop Instructional Materials

Energy Technology Data Exchange (ETDEWEB)

Gibbs, Philip [Brookhaven National Lab. (BNL), Upton, NY (United States); Larsen, Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); O' Brien, Mike [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Edmunds, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2009-02-01

Insiders represent a formidable threat to nuclear facilities. This set of workshop materials covers methodologies to analyze and approaches to mitigate the threat of an insider attempting abrupt and protracted theft of nuclear materials. This particular set of materials is an update of a January 2008 version to add increased emphasis on Material Control and Accounting and its role with respect to protracted insider nuclear material theft scenarios. This report is a compilation of workshop materials consisting of lectures on technical and administrative measures used in Physical Protection (PP) and Material Control and Accounting (MC&A) and methods for analyzing their effectiveness against a postulated insider threat. The postulated threat includes both abrupt and protracted theft scenarios. Presentation is envisioned to be through classroom instruction and discussion. Several practical and group exercises are included for demonstration and application of the analysis approach contained in the lecture/discussion sessions as applied to a hypothetical nuclear facility.

Advances in 4D treatment planning for scanned particle beam therapy - report of dedicated workshops.

Science.gov (United States)

Bert, Christoph; Graeff, Christian; Riboldi, Marco; Nill, Simeon; Baroni, Guido; Knopf, Antje-Christin

2014-12-01

We report on recent progress in the field of mobile tumor treatment with scanned particle beams, as discussed in the latest editions of the 4D treatment planning workshop. The workshop series started in 2009, with about 20 people from 4 research institutes involved, all actively working on particle therapy delivery and development. The first workshop resulted in a summary of recommendations for the treatment of mobile targets, along with a list of requirements to apply these guidelines clinically. The increased interest in the treatment of mobile tumors led to a continuously growing number of attendees: the 2012 edition counted more than 60 participants from 20 institutions and commercial vendors. The focus of research discussions among workshop participants progressively moved from 4D treatment planning to complete 4D treatments, aiming at effective and safe treatment delivery. Current research perspectives on 4D treatments include all critical aspects of time resolved delivery, such as in-room imaging, motion detection, beam application, and quality assurance techniques. This was motivated by the start of first clinical treatments of hepato cellular tumors with a scanned particle beam, relying on gating or abdominal compression for motion mitigation. Up to date research activities emphasize significant efforts in investigating advanced motion mitigation techniques, with a specific interest in the development of dedicated tools for experimental validation. Potential improvements will be made possible in the near future through 4D optimized treatment plans that require upgrades of the currently established therapy control systems for time resolved delivery. But since also these novel optimization techniques rely on the validity of the 4DCT, research focusing on alternative 4D imaging technique, such as MRI based 4DCT generation will continue.

Workshop of Advanced Science Research Center, JAERI. Nuclear physics and nuclear chemistry of superheavy elements

International Nuclear Information System (INIS)

Nishio, Katsuhisa; Nishinaka, Ichiro; Ikezoe, Hiroshi; Nagame, Yuichiro

2004-03-01

A liquid drop model predicts that the fission barrier of a nucleus whose atomic number (Z) is larger than 106 disappears, so that such heavier nuclei as Z > 106 cannot exist. The shell effect, however, drastically changes structure of the fission barrier and stabilizes nucleus against fission, predicting the presence of super heavy element (SHE, Z=114-126) with measurable half-life. In the SHE region, a wave function of outermost electron of an atom, which controls chemical properties of an elements, is disturbed or changed by relativistic effects compared to the one from the non-relativistic model. This suggests that the SHEs have different chemical properties from those of lighter elements belonging to the same family. The chemistry of SHEs requires event by event analysis to reveal their chemical properties, thus is called 'atom-at-a-time chemistry'. Japan Atomic Energy Research Institute (JAERI) has been investigating fusion mechanism between heavy nuclei to find out favorable reactions to produce SHE by using JAERI-tandem and booster accelerator. In the JAERI-tandem facility, isotopes of Rf and Db are produced by using actinide targets such as 248 Cm in order to investigate their chemical properties. The present workshop was held in Advanced Science Research Center of JAERI at February 27-28 (2003) in order to discuss current status and future plans for the heavy element research. The workshop also included topics of the radioactive nuclear beam project forwarded by the JAERI-KEK cooperation and the nuclear transmutation facility of J-PARC. Also included is the nuclear fission process as a decay characteristic of heavy elements. There were sixty participants in the workshop including graduate and undergraduate eleven students. We had guests from Germany and Hungary. Through the workshop, we had a common knowledge that researches on SHE in Japan should fill an important role in the world. (author)

The second advanced ICFA [International Committee for Future Accelerators] beam dynamics workshop, Lugano, Switzerland, April 11-16, 1988: Foreign trip report

International Nuclear Information System (INIS)

Ohnuma, Shoroku.

1988-01-01

This paper summarizes the trip made by Shoroku Ohnuma to the Second Advanced ICFA Beam Dynamics Workshop in Switzerland. Discussed are the experimental and theoretical studies conducted on aperture- related limitations of storage ring performance. Lepton and hadron storage ring machines are mainly mentioned

Continuing Education Workshops in Bioinformatics Positively Impact Research and Careers.

Science.gov (United States)

Brazas, Michelle D; Ouellette, B F Francis

2016-06-01

Bioinformatics.ca has been hosting continuing education programs in introductory and advanced bioinformatics topics in Canada since 1999 and has trained more than 2,000 participants to date. These workshops have been adapted over the years to keep pace with advances in both science and technology as well as the changing landscape in available learning modalities and the bioinformatics training needs of our audience. Post-workshop surveys have been a mandatory component of each workshop and are used to ensure appropriate adjustments are made to workshops to maximize learning. However, neither bioinformatics.ca nor others offering similar training programs have explored the long-term impact of bioinformatics continuing education training. Bioinformatics.ca recently initiated a look back on the impact its workshops have had on the career trajectories, research outcomes, publications, and collaborations of its participants. Using an anonymous online survey, bioinformatics.ca analyzed responses from those surveyed and discovered its workshops have had a positive impact on collaborations, research, publications, and career progression.

Report on the workshop "Decay spectroscopy at CARIBU: advanced fuel cycle applications, nuclear structure and astrophysics". 14-16 April 2011, Argonne National Laboratory, USA.

Energy Technology Data Exchange (ETDEWEB)

Kondev, F.; Carpenter, M.P.; Chowdhury, P.; Clark, J.A.; Lister, C.J.; Nichols, A.L.; Swewryniak, D. (Nuclear Engineering Division); (Univ. of Massachusetts); (Univ. of Surrey)

2011-10-06

A workshop on 'Decay Spectroscopy at CARIBU: Advanced Fuel Cycle Applications, Nuclear Structure and Astrophysics' will be held at Argonne National Laboratory on April 14-16, 2011. The aim of the workshop is to discuss opportunities for decay studies at the Californium Rare Isotope Breeder Upgrade (CARIBU) of the ATLAS facility with emphasis on advanced fuel cycle (AFC) applications, nuclear structure and astrophysics research. The workshop will consist of review and contributed talks. Presentations by members of the local groups, outlining the status of relevant in-house projects and availabile equipment, will also be organized. time will also be set aside to discuss and develop working collaborations for future decay studies at CARIBU. Topics of interest include: (1) Decay data of relevance to AFC applications with emphasis on reactor decay heat; (2) Discrete high-resolution gamma-ray spectroscopy following radioactive decya and related topics; (3) Calorimetric studies of neutron-rich fission framgents using Total ABsorption Gamma-Ray Spectrometry (TAGS) technique; (4) Beta-delayed neutron emissions and related topics; and (5) Decay data needs for nuclear astrophysics.

Challenges of radiotherapy: report on the 4D treatment planning workshop 2013

NARCIS (Netherlands)

Knopf, Antje; Nill, Simeon; Yohannes, Indra; Graeff, Christian; Dowdell, Stephen; Kurz, Christopher; Sonke, Jan-Jakob; Biegun, Aleksandra K; Lang, Stephanie; McClelland, Jamie R.; Champion, Benjamin; Fast, Martin; Wölfelschneider, Jens; Gianoli, Chiara; Rucinski, Antoni; Baroni, Guido; Richter, Christian; van de Water, Steven; Grassberger, Clemens; Weber, Damien; Poulsen, Per; Shimizu, Shinichi; Bert, Christoph

2014-01-01

This report, compiled by experts on the treatment of mobile targets with advanced radiotherapy, summarizes the main conclusions and innovations achieved during the 4D treatment planning workshop 2013. This annual workshop focuses on research aiming to advance 4D radiotherapy treatments, including

WALLTURB International Workshop

CERN Document Server

Jimenez, Javier; Marusic, Ivan

2011-01-01

This book brings together selected contributions from the WALLTURB workshop on ”Understanding and modelling of wall turbulence” held in Lille, France, on April 21st to 23rd 2009. This workshop was organized by the WALLTURB consortium, in order to present to the relevant scientific community the main results of the project and to stimulate scientific discussions around the subject of wall turbulence. The workshop reviewed the recent progress in theoretical, experimental and numerical approaches to wall turbulence. The problems of zero pressure gradient, adverse pressure gradient and separating turbulent boundary layers were addressed in detail with the three approaches, using the most advanced tools. This book is a milestone in the research field, thanks to the high level of the invited speakers and the involvement of the contributors and a testimony of the achievement of the WALLTURB project.

Pinpointing water entries using pulsed neutron and Production logging tools

International Nuclear Information System (INIS)

Mukerji, P.; Oluwa, J.

2003-01-01

A successful work over requires a comprehensive understanding of fluid entries into the wellbore and fluid contact movement in the reservoir. Such information can be obtained by a combination of production logs and saturation-monitoring measurements. The ability to combine pulsed neutron and production logging tools provides the operator with better diagnostics for identifying candidates for remedial actions and greatly increases the possibility of a successful well intervention. Advances in pulsed neutron spectroscopy tools have improved the accuracy and precision of measured carbon/oxygen ratios. Some of the improvements in accuracy and precision have resulted from better tool characterization in a wider variety of logging environments in the calibration facility and new spectral standards. Coincident with the advances in pulsed neutron spectroscopy has been the development of production logging measurements run on a platform common. We will show how the application of pulsed neutron and production logs can optimize subsequent well intervention to reduce water production and/or increase oil production

1st Advanced Marine Renewable Energy Instrumentation Experts Workshop

Energy Technology Data Exchange (ETDEWEB)

none,

2011-10-01

The U.S. marine energy industry is actively pursuing development of offshore wind and marine hydrokinetic (MHK) energy systems. Experience in the wind energy sector demonstrates that new technology development requires thorough measurement and characterization of the environmental conditions prevalent at installation sites and of technology operating in the field. Presently, there are no turn-key instrumentation system solutions that meet the measurement needs of the marine energy industry. The 1st Advanced Marine Renewable Energy Instrumentation Experts Workshop brought together technical experts from government laboratories, academia, and industry representatives from marine energy, wind, offshore oil and gas, and instrumentation developers to present and discuss the instrumentation needs of the marine energy industry. The goals of the meeting were to: 1. Share the latest relevant knowledge among technical experts; 2. Review relevant state-of-the-art field measurement technologies and methods; 3. Review lessons learned from recent field deployments; 4. Identify synergies across different industries; 5. Identify gaps between existing and needed instrumentation capabilities; 6. Understand who are the leading experts; 7. Provide a forum where stakeholders from the marine energy industry could provide substantive input in the development of new marine energy field deployable instrumentation packages.

Accelerating Scientific Advancement for Pediatric Rare Lung Disease Research. Report from a National Institutes of Health-NHLBI Workshop, September 3 and 4, 2015.

Science.gov (United States)

Young, Lisa R; Trapnell, Bruce C; Mandl, Kenneth D; Swarr, Daniel T; Wambach, Jennifer A; Blaisdell, Carol J

2016-12-01

Pediatric rare lung disease (PRLD) is a term that refers to a heterogeneous group of rare disorders in children. In recent years, this field has experienced significant progress marked by scientific discoveries, multicenter and interdisciplinary collaborations, and efforts of patient advocates. Although genetic mechanisms underlie many PRLDs, pathogenesis remains uncertain for many of these disorders. Furthermore, epidemiology and natural history are insufficiently defined, and therapies are limited. To develop strategies to accelerate scientific advancement for PRLD research, the NHLBI of the National Institutes of Health convened a strategic planning workshop on September 3 and 4, 2015. The workshop brought together a group of scientific experts, intramural and extramural investigators, and advocacy groups with the following objectives: (1) to discuss the current state of PRLD research; (2) to identify scientific gaps and barriers to increasing research and improving outcomes for PRLDs; (3) to identify technologies, tools, and reagents that could be leveraged to accelerate advancement of research in this field; and (4) to develop priorities for research aimed at improving patient outcomes and quality of life. This report summarizes the workshop discussion and provides specific recommendations to guide future research in PRLD.

1998 federal technical standards workshop: Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

The theme for the 1998 workshop was Standards Management -- A World of Change and Opportunities. The workshop`s goal was to further the implementation of the National Technology Transfer and Advancement Act of 1995 (Public Law 104-113) through the sharing of standards management success stories, lessons learned, and emerging initiatives within the Executive Branch of the Federal Government. The target audience for this workshop included agency/department and contractor personnel and representatives of standards developing organizations that either used technical standards in their work for the Federal Government of participated in standards writing/management activities in support of the missions and programs of Federal agencies/departments. As with previous standards workshops sponsored by the DOE, views on the technical subject areas under the workshop theme were solicited from and provided by agency Standards Executives and standards program managers, voluntary standards organizations, and the private sector. This report includes vugraphs of the presentations.

NATO Advanced Research Workshop on Approximation by Solutions of Partial Differential Equations, Quadrature Formulae, and Related Topics

CERN Document Server

Goldstein, M; Haussmann, W; Hayman, W; Rogge, L

1992-01-01

This volume consists of the proceedings of the NATO Advanced Research Workshop on Approximation by Solutions of Partial Differential Equations, Quadrature Formulae, and Related Topics, which was held at Hanstholm, Denmark. These proceedings include the main invited talks and contributed papers given during the workshop. The aim of these lectures was to present a selection of results of the latest research in the field. In addition to covering topics in approximation by solutions of partial differential equations and quadrature formulae, this volume is also concerned with related areas, such as Gaussian quadratures, the Pompelu problem, rational approximation to the Fresnel integral, boundary correspondence of univalent harmonic mappings, the application of the Hilbert transform in two dimensional aerodynamics, finely open sets in the limit set of a finitely generated Kleinian group, scattering theory, harmonic and maximal measures for rational functions and the solution of the classical Dirichlet problem. In ...

Working Group summary reports from the Advanced Photon Source reliability workshop

International Nuclear Information System (INIS)

1992-05-01

A workshop was held at APS to address reliability goals for accelerator systems. Seventy-one individuals participated in the workshop, including 30 from other institutions. The goals of the workshop were to: (1) Give attendees an introduction to the basic concepts of reliability analysis. (2) Exchange information on operating experience at existing accelerator facilities and strategies for achieving reliability at facilities under design or in construction. (3) Discuss reliability goals for APS and the means of their achievement. This report contains the working group summary report an APS's following systems: RF Systems; Power Supplies; Magnet Systems; Interlock and Diagnostics; and Vacuum Systems

E-log system in monitoring of residency program: trainees perspective

International Nuclear Information System (INIS)

Iqbal, U.; Gondal, K.M.

2015-01-01

To record residents perspective about the utility of newly introduced E-Log system at the College of Physicians and Surgeons Pakistan (CPSP). Study Design: Sequential mixed method design using survey questionnaire and in-depth interviews. Place and Duration of Study: CPSP, Regional Center, Lahore, from March to June 2014. Methodology: Data was collected from registered trainees through a web-based survey questionnaire on a scale of 1 to 7 about the utility of E-log system. In-depth interviews were conducted with 7 students using non-probability purposive sampling. The interviews were tape recorded and subsequently transcribed. Quantitative data was analyzed using SPSS version 20 and qualitative data was analyzed using content analysis by identifying themes and patterns. Results: A total of 4399 responses were received. Motivation was 4.61± 1.98; 4.33 ± 2.00 remained acknowledgment of control of one's training by the new system. Ease of use got a mean score of 4.56 ± 2.15. Conclusion: The overall acceptance of the students regarding E-Log system was high. Scheduling IT workshop at the start of training will add to the student satisfaction regarding utility of E-Log system. (author)

Results of the Workshop on Two-Phase Flow, Fluid Stability and Dynamics: Issues in Power, Propulsion, and Advanced Life Support Systems

Science.gov (United States)

McQuillen, John; Rame, Enrique; Kassemi, Mohammad; Singh, Bhim; Motil, Brian

2003-01-01

The Two-phase Flow, Fluid Stability and Dynamics Workshop was held on May 15, 2003 in Cleveland, Ohio to define a coherent scientific research plan and roadmap that addresses the multiphase fluid problems associated with NASA s technology development program. The workshop participants, from academia, industry and government, prioritized various multiphase issues and generated a research plan and roadmap to resolve them. This report presents a prioritization of the various multiphase flow and fluid stability phenomena related primarily to power, propulsion, fluid and thermal management and advanced life support; and a plan to address these issues in a logical and timely fashion using analysis, ground-based and space-flight experiments.

NATO Advanced Research Workshop on Preparedness for Nuclear and Radiological Threats

CERN Document Server

Diamond, David

2015-01-01

The nuclear crisis in Fukushima and growing threats of nuclear terrorism must serve as a wake-up call, prompting greater action to prepare ourselves for nuclear and radiological disasters. Our strategy to prepare for these threats is multi-layered and the events of these past years have proved the necessity to re-evaluate the national and international preparedness goals on a scale never before considered. The programme of NATO Advanced Research Workshop on “Preparedness for Nuclear and Radiological Threats” has been focused on science and technology challenges associated with our need to improve the national and international capacity and capability to prevent, protect against, mitigate the effects of, respond to, and recover from the nuclear and radiological disasters, including nuclear and radiological accident, terrorist attack by Improvised Nuclear Device (IND) or by “Dirty Bomb”-Radiological Dispersal Device (RDD), that pose the greatest risk to the national and international security and safety...

Optical Network Testbeds Workshop

Energy Technology Data Exchange (ETDEWEB)

Joe Mambretti

2007-06-01

This is the summary report of the third annual Optical Networking Testbed Workshop (ONT3), which brought together leading members of the international advanced research community to address major challenges in creating next generation communication services and technologies. Networking research and development (R&D) communities throughout the world continue to discover new methods and technologies that are enabling breakthroughs in advanced communications. These discoveries are keystones for building the foundation of the future economy, which requires the sophisticated management of extremely large qualities of digital information through high performance communications. This innovation is made possible by basic research and experiments within laboratories and on specialized testbeds. Initial network research and development initiatives are driven by diverse motives, including attempts to solve existing complex problems, the desire to create powerful new technologies that do not exist using traditional methods, and the need to create tools to address specific challenges, including those mandated by large scale science or government agency mission agendas. Many new discoveries related to communications technologies transition to wide-spread deployment through standards organizations and commercialization. These transition paths allow for new communications capabilities that drive many sectors of the digital economy. In the last few years, networking R&D has increasingly focused on advancing multiple new capabilities enabled by next generation optical networking. Both US Federal networking R&D and other national R&D initiatives, such as those organized by the National Institute of Information and Communications Technology (NICT) of Japan are creating optical networking technologies that allow for new, powerful communication services. Among the most promising services are those based on new types of multi-service or hybrid networks, which use new optical networking

ADVANCES AND CHALLENGES IN SUGARCANE BIOTECHNOLOY AND PLANT PATHOLOGY: A REVIEW OF THE IX PLANT PATHOLOGY WORKSHOP AND VI MOLECULAR BIOLOGY WORKSHOP

Science.gov (United States)

The IX Pathology Workshop and VI Molecular Biology Workshop of the International Society of Sugar Cane Technologists (ISSCT) were organised jointly and hosted by the Colombian Sugarcane Research Centre (CENICAÑA) from 23-27 June 2008 at the Radisson Royal Hotel in Cali, Colombia. The Workshop was we...

Final Report National Laboratory Professional Development Workshop for Underrepresented Participants

Energy Technology Data Exchange (ETDEWEB)

Taylor, Valerie [Texas Engineering Experiment Station, College Station, TX (United States)

2016-11-07

The 2013 CMD-IT National Laboratories Professional Development Workshop for Underrepresented Participants (CMD-IT NLPDev 2013) was held at the Oak Ridge National Laboratory campus in Oak Ridge, TN. from June 13 - 14, 2013. Sponsored by the Department of Energy (DOE) Advanced Scientific Computing Research Program, the primary goal of these workshops is to provide information about career opportunities in computational science at the various national laboratories and to mentor the underrepresented participants through community building and expert presentations focused on career success. This second annual workshop offered sessions to facilitate career advancement and, in particular, the strategies and resources needed to be successful at the national laboratories.

International Workshop on Diagnostics for ITER

CERN Document Server

Gorini, Giuseppe; Sindoni, Elio

1996-01-01

This book of proceedings collects the papers presented at the Workshop on Diagnostics for ITER, held at Villa Monastero, Varenna (Italy), from August 28 to September 1, 1995. The Workshop was organised by the International School of Plasma Physics "Piero Caldirola. " Established in 1971, the ISPP has organised over fifty advanced courses and workshops on topics mainly related to plasma physics. In particular, courses and workshops on plasma diagnostics (previously held in 1975, 1978, 1982, 1986, and 1991) can be considered milestones in the history of this institution. Looking back at the proceedings of the previous meetings in Varenna, one can appreciate the rapid progress in the field of plasma diagnostics over the past 20 years. The 1995 workshop was co-organised by the Istituto di Fisica del Plasma of the National Research Council (CNR). In contrast to previous Varenna meetings on diagnostics, which have covered diagnostics in present-day tokamaks and which have had a substantial tutorial component, the 1...

Public PCs: Log Out or Lose Out

CERN Multimedia

Computer Security Team

2013-01-01

Do you regularly use one of the public Windows or Linux terminals in the CERN library or in front of the Users' Office? Or do you often give presentations or run meetings, workshops or conferences? Did you recently attend a training session in the CERN Training Centre? If you answered at least once with “yes”, we have a plea for you: LOG OUT when done in order to protect your data!   You might recall that CERN considers that “Your Privacy is Paramount”. But this does not come for free. In the few past months, we have received several reports from vigilant people who have spotted open user sessions on public PCs at CERN. Those users simply forgot to log out once their work, training or meeting was over. Their session continued without them being present. Worse, with CERN using a central Single Sign-On (SSO) portal, their login credentials would allow a malicious person at CERN to use those credentials to access that user’s mailbox, DFS ...

Waterloo Workshop on Computer Algebra

CERN Document Server

Zima, Eugene; WWCA-2016; Advances in computer algebra : in honour of Sergei Abramov's' 70th birthday

2018-01-01

This book discusses the latest advances in algorithms for symbolic summation, factorization, symbolic-numeric linear algebra and linear functional equations. It presents a collection of papers on original research topics from the Waterloo Workshop on Computer Algebra (WWCA-2016), a satellite workshop of the International Symposium on Symbolic and Algebraic Computation (ISSAC’2016), which was held at Wilfrid Laurier University (Waterloo, Ontario, Canada) on July 23–24, 2016.   This workshop and the resulting book celebrate the 70th birthday of Sergei Abramov (Dorodnicyn Computing Centre of the Russian Academy of Sciences, Moscow), whose highly regarded and inspirational contributions to symbolic methods have become a crucial benchmark of computer algebra and have been broadly adopted by many Computer Algebra systems.

Recent trend in coal utilization technology. Coal utilization workshop

Energy Technology Data Exchange (ETDEWEB)

Kim, Chon Ho; Son, Ja Ek; Lee, In Chul; Jin, Kyung Tae; Kim, Seong Soo [Korea Inst. of Energy Research, Taejon (Korea, Republic of)

1995-12-01

The 11th Korea-U.S.A. joint workshop on coal utilization technology was held in somerset, Pennsylvania, U.S.A. from october 2 to 3, 1995. In the opening ceremony, Dr.C. Low-el Miller, associate deputy assistant secretary of office of clean coal technology, U.S.DOE, gave congratulatory remarks and Dr. Young Mok Son, president of KIER, made a keynote address. In this workshop, 30 papers were presented in the fields of emission control technology, advanced power generation systems, and advanced coal cleaning and liquid fuels. Especially, from the Korean side, not only KIER but also other private research institutes and major engineering companies including KEPCO, Daewoo Institute of Construction Technology, Jindo Engineering and Construction Co. Daewoo Institute for Advanced Engineering and universities participated in this workshop, reflecting their great interests. Attendants actively discussed about various coal utilization technologies and exchanged scientific and technical information on the state-of-art clean coal technologies under development. (author)

Advanced insider threat mitigation workshop instructional materials

Energy Technology Data Exchange (ETDEWEB)

Gibbs, Philip [Brookhaven National Lab. (BNL), Upton, NY (United States); Larsen, Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); O Brien, Mike [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Edmunds, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2008-11-01

Insiders represent a formidable threat to nuclear facilities. This set of workshop materials covers methodologies to analyze and approaches to mitigate the threat of an insider attempting abrupt and protracted theft of nuclear materials. This particular set of materials is a n update of a January 2008 version to add increased emphasis on Material Control and Accounting and its role with respect to protracted insider nuclear material theft scenarios.

Effect of the science teaching advancement through modeling physical science professional development workshop on teachers' attitudes, beliefs and content knowledge and students' content knowledge

Science.gov (United States)

Dietz, Laura

The Science Teaching Advancement through Modeling Physical Science (STAMPS) professional development workshop was evaluated for effectiveness in improving teachers' and students' content knowledge. Previous research has shown modeling to be an effective method of instruction for improving student and teacher content knowledge, evidenced by assessment scores. Data includes teacher scores on the Force Concept Inventory (FCI; Hestenes, Wells, & Swackhamer, 1992) and the Chemistry Concept Inventory (CCI; Jenkins, Birk, Bauer, Krause, & Pavelich, 2004), as well as student scores on a physics and chemistry assessment. Quantitative data is supported by teacher responses to a post workshop survey and classroom observations. Evaluation of the data shows that the STAMPS professional development workshop was successful in improving both student and teacher content knowledge. Conclusions and suggestions for future study are also included.

Human Factors and Data Logging Processes With the Use of Advanced Technology for Adults With Type 1 Diabetes: Systematic Integrative Review.

Science.gov (United States)

Waite, Marion; Martin, Clare; Franklin, Rachel; Duce, David; Harrison, Rachel

2018-03-15

People with type 1 diabetes (T1D) undertake self-management to prevent short and long-term complications. Advanced technology potentially supports such activities but requires consideration of psychological and behavioral constructs and usability issues. Economic factors and health care provider capacity influence access and uptake of advanced technology. Previous reviews have focused upon clinical outcomes or were descriptive or have synthesized studies on adults with those on children and young people where human factors are different. This review described and examined the relationship between human factors and adherence with technology for data logging processes in adults with T1D. A systematic literature search was undertaken by using the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Quality appraisal was undertaken and data were abstracted and categorized into the themes that underpinned the human factor constructs that were examined. A total of 18 studies were included. A total of 6 constructs emerged from the data analysis: the relationship between adherence to data logging and measurable outcomes; satisfaction with the transition to advanced technology for self-management; use of advanced technology and time spent on diabetes-related activities; strategies to mediate the complexities of diabetes and the use of advanced technology; cognition in the wild; and meanings, views, and perspectives from the users of technology. Increased treatment satisfaction was found on transition from traditional to advanced technology use-insulin pump and continuous glucose monitoring (CGM); the most significant factor was when blood glucose levels were consistently technology. The results suggested frustrations with CGM, continuous subcutaneous insulin infusion, calibration of devices, and alarms. Furthermore implications for "body image" and the way in which "significant others" impacted on the behavior and attitude of the

Advanced Technology for Engineering Education

Science.gov (United States)

Noor, Ahmed K. (Compiler); Malone, John B. (Compiler)

1998-01-01

This document contains the proceedings of the Workshop on Advanced Technology for Engineering Education, held at the Peninsula Graduate Engineering Center, Hampton, Virginia, February 24-25, 1998. The workshop was jointly sponsored by the University of Virginia's Center for Advanced Computational Technology and NASA. Workshop attendees came from NASA, other government agencies, industry and universities. The objectives of the workshop were to assess the status of advanced technologies for engineering education and to explore the possibility of forming a consortium of interested individuals/universities for curriculum reform and development using advanced technologies. The presentations covered novel delivery systems and several implementations of new technologies for engineering education. Certain materials and products are identified in this publication in order to specify adequately the materials and products that were investigated in the research effort. In no case does such identification imply recommendation or endorsement of products by NASA, nor does it imply that the materials and products are the only ones or the best ones available for this purpose. In many cases equivalent materials and products are available and would probably produce equivalent results.

PS2004 Light-harvesting Systems Workshop

Energy Technology Data Exchange (ETDEWEB)

Blankenship, Robert E.

2005-01-01

This special issue of the international scientific research journal Photosynthesis Research consists of 25 original peer-reviewed contributions from participants in the PS 2004 Lisht-Harvesting Systems Workshop. This workshop was held from 26-29, 2004 at Hotel Le Chantecler, Sainte-Adele, Quebec, Canada. The workshop was a satellite meeting of the XIII International Congress on Photosynthesis held August 29-September 3, 2004 in Montreal, Canada. The workshope dealt with all types of photosynthetic antenna systems and types of organisms, including anoxygenic photosynthetic bacteria, cyanobacteria, algae and higher plants, as well as in vitro studies of isolated pigments. This collection of papers is a good representation of the highly interdisciplinary nature of modern research on photosynthetic antenna complexes, utilizing techniques of advanced spectroscopy, biochemistry, molecular biology, synthetic chemistry and structural determination to understand these diverse and elegant molecular complexes.

The Astronomy Workshop

Science.gov (United States)

Hamilton, D. P.; Asbury, M. L.; Proctor, A.

2001-12-01

The Astronomy Workshop (http://janus.astro.umd.edu) is an interactive online astronomy resource developed, and maintained at the University of Maryland, for use by students, educators and the general public. The Astronomy Workshop has been extensively tested and used successfully at many different levels, including High School and Junior High School science classes, University introductory astronomy courses, and University intermediate and advanced astronomy courses. Some topics currently covered in the Astronomy Workshop are: Animated Orbits of Planets and Moons: The orbits of the nine planets and 91 known planetary satellites are shown in animated, to-scale drawings. The orbiting bodies move at their correct relative speeds about their parent, which is rendered as an attractive, to-scale gif image. Solar System Collisions: This most popular of our applications shows what happens when an asteroid or comet with user-defined size and speed impacts a given planet. The program calculates many effects, including the country impacted (if Earth is the target), energy of the explosion, crater size, magnitude of the planetquake generated. It also displays a relevant image (e.g. terrestrial crater, lunar crater, etc.). Planetary and Satellite Data Calculators: These tools allow the user to easily calculate physical data for all of the planets or satellites simultaneously, making comparison very easy. Orbital Simulations: These tools allow the student to investigate different aspects of the three-body problem of celestial mechanics. Astronomy Workshop Bulletin Board: Get innovative teaching ideas and read about in-class experiences with the Astronomy Workshop. Share your ideas with other educators by posting on the Bulletin Board. Funding for the Astronomy Workshop is provided by the National Science Foundation.

Workshop report : joint workshop on liability issues in advanced vehicle control and automated highway systems

Science.gov (United States)

1997-02-05

The National Automated Highway System Consortium (NAHSC), ITS America and the American Association of State Highway & Transportation Officials (AASHTO) co-sponsored a two-day workshop in Washington, DC on February 5-6, 1997 to examine the liability i...

Mechanics and model-based control of advanced engineering systems

CERN Document Server

Irschik, Hans; Krommer, Michael

2014-01-01

Mechanics and Model-Based Control of Advanced Engineering Systems collects 32 contributions presented at the International Workshop on Advanced Dynamics and Model Based Control of Structures and Machines, which took place in St. Petersburg, Russia in July 2012. The workshop continued a series of international workshops, which started with a Japan-Austria Joint Workshop on Mechanics and Model Based Control of Smart Materials and Structures and a Russia-Austria Joint Workshop on Advanced Dynamics and Model Based Control of Structures and Machines. In the present volume, 10 full-length papers based on presentations from Russia, 9 from Austria, 8 from Japan, 3 from Italy, one from Germany and one from Taiwan are included, which represent the state of the art in the field of mechanics and model based control, with particular emphasis on the application of advanced structures and machines.

Boiling water reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and workshop material and sponsors workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 simulator from the Moscow Engineering and Physics Institute, Russian Federation is presented in the IAEA publication: Training Course Series No. 21 'WWER-1000 Reactor Simulator' (2002). Course material for workshops using a pressurized water reactor (PWR) simulator developed by Cassiopeia Technologies Incorporated, Canada, is presented in the IAEA publication: Training Course Series No. 22 'Pressurized Water Reactor Simulator' (2003). This report consists of course material for workshops using a boiling water reactor (BWR) simulator. Cassiopeia Technologies Incorporated, developed the simulator and prepared this report for the IAEA

Borehole logging for uranium exploration

International Nuclear Information System (INIS)

1982-01-01

The present text has been prepared taking into account the requirements of both developing countries, which might be at an incipient stage of uranium exploration, and industrialized countries, where more advanced exploration and resource evaluation techniques are commonly in use. While it was felt necessary to include some discussion of exploration concepts and fundamental physical principles underlying various logging methods, it was not the intention of the consultants to provide a thorough, detailed explanation of the various techniques, or even to give a comprehensive listing thereof. However, a list of references has been included, and it is strongly recommended that the serious student of mineral logging consult this list for further guidance

Report from the SciDB Workshop

Directory of Open Access Journals (Sweden)

J Becla

2008-11-01

Full Text Available A mini-workshop with representatives from the data-driven science and database research communities was organized in response to suggestions at the first XLDB Workshop. The goal was to develop common requirements and primitives for a next-generation database management system that scientists would use, including those from high-energy physics, astronomy, biology, geoscience and fusion, in order to stimulate research and advance technology. These requirements were thought by the database researchers to be novel and unlikely to be fully met by current commercial vendors. The two groups accordingly decided to explore building a new open source DBMS. This paper is the final report of the discussions and activities at the workshop

National Postirradiation Examination Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Schulthess, Jason L

2011-06-01

A National Post-Irradiation-Examination (PIE) Workshop was held March 29-30, 2011, in Washington D.C., stimulated by the DOE Acting Assistant Secretary for Nuclear Energy approval on January 31, 2011 of the “Mission Need Statement for Advanced Post-Irradiation Examination Capability”. As stated in the Mission Need, “A better understanding of nuclear fuels and material performance in the nuclear environment, at the nanoscale and lower, is critical to the development of innovative fuels and materials required for tomorrow’s nuclear energy systems.” (2011) Developing an advanced post-irradiation capability is the most important thing we can do to advance nuclear energy as an option to meeting national energy goals. Understanding the behavior of fuels and materials in a nuclear reactor irradiation environment is the limiting factor in nuclear plant safety, longevity, efficiency, and economics. The National PIE Workshop is part of fulfilling or addressing Department of Energy (DOE) missions in safe and publically acceptable nuclear energy. Several presentations were given during the opening of the workshop. Generally speaking, these presentations established that we cannot continue to rely on others in the world to provide the capabilities we need to move forward with nuclear energy technology. These presentations also generally identified the need for increased microstructural understanding of fuels and materials to be coupled with modeling and simulation, and increased accessibility and infrastructure to facilitate the interaction between national laboratories and participating organizations. The overall results of the work of the presenters and panels was distilled into four primary needs 1. Understanding material changes in the extreme nuclear environment at the nanoscale. Nanoscale studies have significant importance due to the mechanisms that cause materials to degrade, which actually occur on the nanoscale. 2. Enabling additional proficiency in

NATO Advanced Research Workshop on Incommensurate Crystals, Liquid Crystals, and Quasi-Crystals

CERN Document Server

Clark, N

1988-01-01

In this NATO-sponsored Advanced Research Workshop we succeeded in bringing together approximately forty scientists working in the three main areas of structurally incommensurate materials: incommensurate crystals (primarily ferroelectric insulators), incommensurate liquid crystals, and metallic quasi-crystals. Although these three classes of materials are quite distinct, the commonality of the physics of the origin and descrip­ tion of these incommensurate structures is striking and evident in these proceedings. A measure of the success of this conference was the degree to which interaction among the three subgroups occurred; this was facili­ tated by approximately equal amounts of theory and experiment in the papers presented. We thank the University of Colorado for providing pleasant housing and conference facilities at a modest cost, and we are especially grate­ ful to Ann Underwood, who retyped all the manuscripts into camera-ready form. J. F. Scott Boulder, Colorado N. A. Clark v CONTENTS PART I: INCO...

Emerging methods and tools for environmental risk assessment, decision-making, and policy for nanomaterials: summary of NATO Advanced Research Workshop

International Nuclear Information System (INIS)

Linkov, Igor; Steevens, Jeffery; Adlakha-Hutcheon, Gitanjali; Bennett, Erin; Chappell, Mark; Colvin, Vicki; Davis, J. Michael; Davis, Thomas; Elder, Alison; Foss Hansen, Steffen; Hakkinen, Pertti Bert; Hussain, Saber M.; Karkan, Delara; Korenstein, Rafi; Lynch, Iseult; Metcalfe, Chris

2009-01-01

Nanomaterials and their associated technologies hold promising opportunities for the development of new materials and applications in a wide variety of disciplines, including medicine, environmental remediation, waste treatment, and energy conservation. However, current information regarding the environmental effects and health risks associated with nanomaterials is limited and sometimes contradictory. This article summarizes the conclusions of a 2008 NATO workshop designed to evaluate the wide-scale implications (e.g., benefits, risks, and costs) of the use of nanomaterials on human health and the environment. A unique feature of this workshop was its interdisciplinary nature and focus on the practical needs of policy decision makers. Workshop presentations and discussion panels were structured along four main themes: technology and benefits, human health risk, environmental risk, and policy implications. Four corresponding working groups (WGs) were formed to develop detailed summaries of the state-of-the-science in their respective areas and to discuss emerging gaps and research needs. The WGs identified gaps between the rapid advances in the types and applications of nanomaterials and the slower pace of human health and environmental risk science, along with strategies to reduce the uncertainties associated with calculating these risks.

Geometric Methods in Physics : XXXIII Workshop

CERN Document Server

Bieliavsky, Pierre; Odzijewicz, Anatol; Schlichenmaier, Martin; Voronov, Theodore

2015-01-01

This book presents a selection of papers based on the XXXIII Białowieża Workshop on Geometric Methods in Physics, 2014. The Białowieża Workshops are among the most important meetings in the field and attract researchers from both mathematics and physics. The articles gathered here are mathematically rigorous and have important physical implications, addressing the application of geometry in classical and quantum physics. Despite their long tradition, the workshops remain at the cutting edge of ongoing research. For the last several years, each Białowieża Workshop has been followed by a School on Geometry and Physics, where advanced lectures for graduate students and young researchers are presented; some of the lectures are reproduced here. The unique atmosphere of the workshop and school is enhanced by its venue, framed by the natural beauty of the Białowieża forest in eastern Poland. The volume will be of interest to researchers and graduate students in mathematical physics, theoretical physics and m...

Geometric Methods in Physics : XXXII Workshop

CERN Document Server

Bieliavsky, Pierre; Odesskii, Alexander; Odzijewicz, Anatol; Schlichenmaier, Martin; Voronov, Theodore; Geometric Methods in Physics

2014-01-01

The Białowieża Workshops on Geometric Methods in Physics, which are hosted in the unique setting of the Białowieża natural forest in Poland, are among the most important meetings in the field. Every year some 80 to 100 participants from both the mathematics and physics world join to discuss new developments and to exchange ideas. The current volume was produced on the occasion of the 32nd meeting in 2013. It is now becoming a tradition that the Workshop is followed by a School on Geometry and Physics, which consists of advanced lectures for graduate students and young researchers. Selected speakers at the 2013 Workshop were asked to contribute to this book, and their work was supplemented by additional review articles. The selection shows that, despite its now long tradition, the workshop remains at the cutting edge of research. The 2013 Workshop also celebrated the 75th birthday of Daniel Sternheimer, and on this occasion the discussion mainly focused on his contributions to mathematical physics such as ...

Fluid-Rock Characterization and Interactions in NMR Well Logging

Energy Technology Data Exchange (ETDEWEB)

Hirasaki, George J.; Mohanty, Kishore K.

2003-02-10

The objective of this project was to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity.

Workshop on Processing Physic-Chemistry Advanced – WPPCA

International Nuclear Information System (INIS)

2016-01-01

In the present volume of Journal of Physics: Conference Series we publish the proceedings of the “2nd Workshop on Processing Physic-Chemistry advanced (WPPCA)”, that was held from, April 4-8, 2016, at the Universidad Industrial de Santander (UIS), Bucaramanga, Colombia. The proceedings consist of 17 contributions that were presented as plenary talks at the event. The abstracts of all participants contributions were published in the Abstract Book with ISSN 2500-8420. The scientific program of the 2nd WPPCA consisted of 12 Magisterial Conferences, 28 Poster Presentations and 2 Courses with the participation of undergraduate and graduate students, professors, researchers and entrepreneurs from Colombia, Spain, Unite States of America, Mexico and Chile. Moreover, the 2nd WPPCA allowed to establish a shared culture of the research and innovation that enriches the area of the processing physical-chemistry of the materials and the industrial applications. All papers in these Proceedings refer to one from the following topics: Semiconductors, Superconductivity, Nanostructure Materials and Modelling, Simulation and Diagnostics. The editor hopes that those interested in the area of the science of materials can to enjoy this reading, that reflects a wide variety of current issues. On behalf of the organizing committee of the 2nd WPPCA, we are extremely thankful to all authors for providing their valuable contributions for these Proceedings as well as the reviewers for their constructive recommendations and criticism aiding to improve the presented articles. Besides, especially we appreciate the great support provided by the Sponsors and Partners. (paper)

Workshop on Educational Data Mining @ ICALT07 (EDM@ICALT07)

NARCIS (Netherlands)

Beck, J.E.; Calders, T.; Pechenizkiy, M.; Viola, S.R.; Spector, J.M.; Sampson, D.G.; Okamoto, T.; Cerri, S.A.; Ueno, M.; Kashihara, A.

2007-01-01

The educational data mining workshop1 held in conjunction with the 7 IEEE International Conference on Advanced Learning Technologies (ICALT) in Niigata, Japan on July 18-20, 2007. EDM@ICALT07 continues the series of Workshops organized by the International Working Group on Educational Data Mining

Dual detector neutron lifetime log: theory and practical applications

International Nuclear Information System (INIS)

Serpas, C.J.; Wichmann, P.A.; Fertl, W.H.; DeVries, M.R.; Rndall, R.R.

1977-01-01

The Neutron Lifetime Log instrumentation has continued to evolve and now is equipped with dual detectors for increased ease in gas detection and also a ratio response for a simultaneous porosity determination. A good deal of experimentation was involved to minimize both lithology and salinity effects on the porosity indication. This paper contains a discussion of the theory and concepts related to the application of the Dual Detector Neutron Lifetime Log (DNLL). It is important to note that with these advances the recording of thermal neutron capture cross section (Σ) remains consistent with the past measurements of earlier generations of instruments as the most accurate determination of this parameter. A number of field examples of the newly logged results are shown. These field cases include Dual Detector NLL's run thru the drill strings of highly deviated holes when difficulties were encountered in getting conventional open hole logs to bottom, logs thru open perforations and hot radioactive zones, comparisons of the large and small diameter instruments, logs with anomalous fluids in the annulus, logs thru multiple casing strings, and a number of other examples

Science Drivers and Technical Challenges for Advanced Magnetic Resonance

Energy Technology Data Exchange (ETDEWEB)

Mueller, Karl T.; Pruski, Marek; Washton, Nancy M.; Lipton, Andrew S.

2013-03-07

This report recaps the "Science Drivers and Technical Challenges for Advanced Magnetic Resonance" workshop, held in late 2011. This exploratory workshop's goal was to discuss and address challenges for the next generation of magnetic resonance experimentation. During the workshop, participants from throughout the world outlined the science drivers and instrumentation demands for high-field dynamic nuclear polarization (DNP) and associated magnetic resonance techniques, discussed barriers to their advancement, and deliberated the path forward for significant and impactful advances in the field.

Proceedings of the Eighteenth Annual Software Engineering Workshop

Science.gov (United States)

1993-01-01

The workshop provided a forum for software practitioners from around the world to exchange information on the measurement, use, and evaluation of software methods, models, and tools. This year, approximately 450 people attended the workshop, which consisted of six sessions on the following topics: the Software Engineering Laboratory, measurement, technology assessment, advanced concepts, process, and software engineering issues in NASA. Three presentations were given in each of the topic areas. The content of those presentations and the research papers detailing the work reported are included in these proceedings. The workshop concluded with a tutorial session on how to start an Experience Factory.

Pressurized water reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 reactor department simulator from the Moscow Engineering and Physics Institute, the Russian Federation is presented in the IAEA Training Course Series No. 21 'WWER-1000 Reactor Simulator' (2002). Course material for workshops using a boiling water reactor simulator developed for the IAEA by Cassiopeia Technologies Incorporated of Canada (CTI) is presented in the IAEA publication: Training Course Series No.23 'Boiling Water Reactor Simulator' (2003). This report consists of course material for workshops using a pressurized water reactor simulator

NATO Advanced Research Workshop on Geometrical Derivatives of Energy Surfaces and Molecular Properties

CERN Document Server

Simons, Jack

1986-01-01

The development and computational implementation of analytical expres­ sions for the low-order derivatives of electronic energy surfaces and other molecular properties has undergone rapid growth in recent years. It is now fairly routine for chemists to make use of energy gradient information in locating and identifying stable geometries and transition states. The use of second analytical derivative (Hessian or curvature) expressions is not yet routine, and third and higher energy derivatives as well as property (e.g., dipole moment, polarizability) derivatives are just beginning to be applied to chemical problems. This NATO Advanced Research Workshop focused on analyzing the re­ lative merits of various strategies for deriving the requisite analyti­ cal expressions, for computing necessary integral derivatives and wave­ function parameter derivatives, and for efficiently coding these expres­ sions on conventional scalar machines and vector-oriented computers. The participant list contained many scientist...

Workshop on advances in smooth particle hydrodynamics

Energy Technology Data Exchange (ETDEWEB)

Wingate, C.A.; Miller, W.A.

1993-12-31

This proceedings contains viewgraphs presented at the 1993 workshop held at Los Alamos National Laboratory. Discussed topics include: negative stress, reactive flow calculations, interface problems, boundaries and interfaces, energy conservation in viscous flows, linked penetration calculations, stability and consistency of the SPH method, instabilities, wall heating and conservative smoothing, tensors, tidal disruption of stars, breaking the 10,000,000 particle limit, modelling relativistic collapse, SPH without H, relativistic KSPH avoidance of velocity based kernels, tidal compression and disruption of stars near a supermassive rotation black hole, and finally relativistic SPH viscosity and energy.

Workshop Physics Activity Guide, Module 4: Electricity and Magnetism

Science.gov (United States)

Laws, Priscilla W.

2004-05-01

The Workshop Physics Activity Guide is a set of student workbooks designed to serve as the foundation for a two-semester calculus-based introductory physics course. It consists of 28 units that interweave text materials with activities that include prediction, qualitative observation, explanation, equation derivation, mathematical modeling, quantitative experiments, and problem solving. Students use a powerful set of computer tools to record, display, and analyze data, as well as to develop mathematical models of physical phenomena. The design of many of the activities is based on the outcomes of physics education research. The Workshop Physics Activity Guide is supported by an Instructor's Website that: (1) describes the history and philosophy of the Workshop Physics Project; (2) provides advice on how to integrate the Guide into a variety of educational settings; (3) provides information on computer tools (hardware and software) and apparatus; and (4) includes suggested homework assignments for each unit. Log on to the Workshop Physics Project website at http://physics.dickinson.edu/ Workshop Physics is a component of the Physics Suite--a collection of materials created by a group of educational reformers known as the Activity Based Physics Group. The Physics Suite contains a broad array of curricular materials that are based on physics education research, including: Understanding Physics, by Cummings, Laws, Redish and Cooney (an introductory textbook based on the best-selling text by Halliday/Resnick/Walker) RealTime Physics Laboratory Modules Physics by Inquiry (intended for use in a workshop setting) Interactive Lecture Demonstration Tutorials in Introductory Physics Activity Based Tutorials (designed primarily for use in recitations)

Flywheel energy storage workshop

Energy Technology Data Exchange (ETDEWEB)

O`Kain, D.; Carmack, J. [comps.

1995-12-31

Since the November 1993 Flywheel Workshop, there has been a major surge of interest in Flywheel Energy Storage. Numerous flywheel programs have been funded by the Advanced Research Projects Agency (ARPA), by the Department of Energy (DOE) through the Hybrid Vehicle Program, and by private investment. Several new prototype systems have been built and are being tested. The operational performance characteristics of flywheel energy storage are being recognized as attractive for a number of potential applications. Programs are underway to develop flywheels for cars, buses, boats, trains, satellites, and for electric utility applications such as power quality, uninterruptible power supplies, and load leveling. With the tremendous amount of flywheel activity during the last two years, this workshop should again provide an excellent opportunity for presentation of new information. This workshop is jointly sponsored by ARPA and DOE to provide a review of the status of current flywheel programs and to provide a forum for presentation of new flywheel technology. Technology areas of interest include flywheel applications, flywheel systems, design, materials, fabrication, assembly, safety & containment, ball bearings, magnetic bearings, motor/generators, power electronics, mounting systems, test procedures, and systems integration. Information from the workshop will help guide ARPA & DOE planning for future flywheel programs. This document is comprised of detailed viewgraphs.

Proceedings of the 2004 NASA/ONR Circulation Control Workshop, Part 1

Science.gov (United States)

Jones, Gregory S. (Editor); Joslin, Ronald D. (Editor)

2005-01-01

As technological advances influence the efficiency and effectiveness of aerodynamic and hydrodynamic applications, designs and operations, this workshop was intended to address the technologies, systems, challenges and successes specific to Coanda driven circulation control in aerodynamics and hydrodynamics. A major goal of this workshop was to determine the 2004 state-of-the-art in circulation control and understand the roadblocks to its application. The workshop addressed applications, CFD, and experiments related to circulation control, emphasizing fundamental physics, systems analysis, and applied research. The workshop consisted of 34 single session oral presentations and written papers that focused on Naval hydrodynamic vehicles (e.g. submarines), Fixed Wing Aviation, V/STOL platforms, propulsion systems (including wind turbine systems), ground vehicles (automotive and trucks) and miscellaneous applications (e.g., poultry exhaust systems and vacuum systems). Several advanced CFD codes were benchmarked using a two-dimensional NCCR circulation control airfoil. The CFD efforts highlighted inconsistencies in turbulence modeling, separation and performance predictions.

Workshop on wave-ice interaction

Science.gov (United States)

Wadhams, Peter; Squire, Vernon; Rottier, Philip; Liu, Antony; Dugan, John; Czipott, Peter; Shen, Hayley

The subject of wave-ice interaction has been advanced in recent years by small groups of researchers working on a similar range of topics in widely separated geographic locations. Their recent studies inspired a workshop on wave-ice interaction held at the Scott Polar Research Institute, University of Cambridge, England, December 16-18, 1991, where theories in all aspects of the physics of wave-ice interaction were compared.Conveners of the workshop hoped that plans for future observational and theoretical work dealing with outstanding issues in a collaborative way would emerge. The workshop, organized by the Commission on Sea Ice of the International Association for Physical Sciences of the Ocean (IAPSO), was co-chaired by Vernon Squire, professor of mathematics and statistics at the University of Otago, New Zealand, and Peter Wadhams, director of the Scott Polar Research Institute. Participants attended from Britain, Finland, New Zealand, Norway, and the United States.

The 3d International Workshop on Computational Electronics

Science.gov (United States)

Goodnick, Stephen M.

1994-09-01

The Third International Workshop on Computational Electronics (IWCE) was held at the Benson Hotel in downtown Portland, Oregon, on May 18, 19, and 20, 1994. The workshop was devoted to a broad range of topics in computational electronics related to the simulation of electronic transport in semiconductors and semiconductor devices, particularly those which use large computational resources. The workshop was supported by the National Science Foundation (NSF), the Office of Naval Research and the Army Research Office, as well as local support from the Oregon Joint Graduate Schools of Engineering and the Oregon Center for Advanced Technology Education. There were over 100 participants in the Portland workshop, of which more than one quarter represented research groups outside of the United States from Austria, Canada, France, Germany, Italy, Japan, Switzerland, and the United Kingdom. There were a total 81 papers presented at the workshop, 9 invited talks, 26 oral presentations and 46 poster presentations. The emphasis of the contributions reflected the interdisciplinary nature of computational electronics with researchers from the Chemistry, Computer Science, Mathematics, Engineering, and Physics communities participating in the workshop.

Advanced Computational Materials Science: Application to Fusion and Generation IV Fission Reactors (Workshop Report)

Energy Technology Data Exchange (ETDEWEB)

Stoller, RE

2004-07-15

The ''Workshop on Advanced Computational Materials Science: Application to Fusion and Generation IV Fission Reactors'' was convened to determine the degree to which an increased effort in modeling and simulation could help bridge the gap between the data that is needed to support the implementation of these advanced nuclear technologies and the data that can be obtained in available experimental facilities. The need to develop materials capable of performing in the severe operating environments expected in fusion and fission (Generation IV) reactors represents a significant challenge in materials science. There is a range of potential Gen-IV fission reactor design concepts and each concept has its own unique demands. Improved economic performance is a major goal of the Gen-IV designs. As a result, most designs call for significantly higher operating temperatures than the current generation of LWRs to obtain higher thermal efficiency. In many cases, the desired operating temperatures rule out the use of the structural alloys employed today. The very high operating temperature (up to 1000 C) associated with the NGNP is a prime example of an attractive new system that will require the development of new structural materials. Fusion power plants represent an even greater challenge to structural materials development and application. The operating temperatures, neutron exposure levels and thermo-mechanical stresses are comparable to or greater than those for proposed Gen-IV fission reactors. In addition, the transmutation products created in the structural materials by the high energy neutrons produced in the DT plasma can profoundly influence the microstructural evolution and mechanical behavior of these materials. Although the workshop addressed issues relevant to both Gen-IV and fusion reactor materials, much of the discussion focused on fusion; the same focus is reflected in this report. Most of the physical models and computational methods

Second advanced ICFA beam dynamics workshop on aperture-related limitations of the performance and beam lifetime in storage rings

International Nuclear Information System (INIS)

Hagel, J.; Keil, E.

1988-01-01

These proceedings contain the papers presented at the 'Second advanced beam dynamics workshop on aperture-related limitations of the performance and beam lifetime in storage rings', which was organized in Lugano, Switzerland, from 11 to 16 April 1988, by the Beam Dynamics Panel of the International Committee for Future Accelerators (ICFA). The papers cover experiments on existing accelerators, analytical methods for determining amplitude limitations, criteria for the properties of the circulating beam and for the quality of accelerator components, and compensation schemes for field defects. (orig.)

Workshop Report on Space Weather Risks and Society

Science.gov (United States)

Langhoff, Stephanie R.; Straume, Tore

2012-01-01

As technological innovations produce new capabilities, complexities, and interdependencies, our susceptibility to the societal impacts of space weather increase. There is real concern in the scientific community that our infrastructure would be at significant risk if a major geomagnetic storm should occur. To discuss the societal impacts of space weather, we brought together an interdisciplinary group of subject matter experts and societal stakeholders to participate in a workshop entitled Space Weather Risks and Society. The workshop was held at Ames Research Center (ARC) on 15-16 October 2011. The workshop was co-sponsored by NASA Ames Research Center (ARC), the Lockheed Martin Advanced Technology Center (LMATC), the Space Weather Prediction Center (SWPC, part of the National Oceanic and Atmospheric Administration NOAA), and the Rutherford Appleton Laboratory (RAL, part of the UK Science and Technology Facilities Council STFC). The workshop is part of a series of informal weekend workshops hosted by Center Director Pete Worden.

XXXIV Bialowieza Workshop on Geometric Methods in Physics

CERN Document Server

Ali, S; Bieliavsky, Pierre; Odzijewicz, Anatol; Schlichenmaier, Martin; Voronov, Theodore

2016-01-01

This book features a selection of articles based on the XXXIV Białowieża Workshop on Geometric Methods in Physics, 2015. The articles presented are mathematically rigorous, include important physical implications and address the application of geometry in classical and quantum physics. Special attention deserves the session devoted to discussions of Gerard Emch's most important and lasting achievements in mathematical physics. The Białowieża workshops are among the most important meetings in the field and gather participants from mathematics and physics alike. Despite their long tradition, the Workshops remain at the cutting edge of ongoing research. For the past several years, the Białowieża Workshop has been followed by a School on Geometry and Physics, where advanced lectures for graduate students and young researchers are presented. The unique atmosphere of the Workshop and School is enhanced by the venue, framed by the natural beauty of the Białowieża forest in eastern Poland.

18th International Workshop on Radiation Imaging Detectors

CERN Document Server

2016-01-01

The International Workshops on Radiation Imaging Detectors are held yearly and provide an international forum for discussing current research and developments in the area of position sensitive detectors for radiation imaging, including semiconductor detectors, gas and scintillator-based detectors. Topics include processing and characterization of detector materials, hybridization and interconnect technologies, design of counting or integrating electronics, readout and data acquisition systems, and applications in various scientific and industrial fields. The workshop will have plenary sessions with invited and contributed papers presented orally and in poster sessions. The invited talks will be chosen to review recent advances in different areas covered in the workshop.

MATHEON Workshop 2013

CERN Document Server

Calderbank, Robert; Kutyniok, Gitta; Vybíral, Jan

2015-01-01

Since publication of the initial papers in 2006, compressed sensing has captured the imagination of the international signal processing community, and the mathematical foundations are nowadays quite well understood. Parallel to the progress in mathematics, the potential applications of compressed sensing have been explored by many international groups of, in particular, engineers and applied mathematicians, achieving very promising advances in various areas such as communication theory, imaging sciences, optics, radar technology, sensor networks, or tomography. Since many applications have reached a mature state, the research center MATHEON in Berlin focusing on "Mathematics for Key Technologies", invited leading researchers on applications of compressed sensing from mathematics, computer science, and engineering to the "MATHEON Workshop 2013: Compressed Sensing and its Applications” in December 2013. It was the first workshop specifically focusing on the applications of compressed sensing. This book featur...

Chemical applications of synchrotron radiation: Workshop report

International Nuclear Information System (INIS)

1989-04-01

The most recent in a series of topical meetings for Advanced Photon Source user subgroups, the Workshop on Chemical Applications of Synchrotron Radiation (held at Argonne National Laboratory, October 3-4, 1988) dealt with surfaces and kinetics, spectroscopy, small-angle scattering, diffraction, and topography and imaging. The primary objectives were to provide an educational resource for the chemistry community on the scientific research being conducted at existing synchrotron sources and to indicate some of the unique opportunities that will be made available with the Advanced Photon Source. The workshop organizers were also interested in gauging the interest of chemists in the field of synchrotron radiation. Interest expressed at the meeting has led to initial steps toward formation of a Chemistry Users Group at the APS. Individual projects are processed separately for the data bases

Chemical applications of synchrotron radiation: Workshop report

Energy Technology Data Exchange (ETDEWEB)

1989-04-01

The most recent in a series of topical meetings for Advanced Photon Source user subgroups, the Workshop on Chemical Applications of Synchrotron Radiation (held at Argonne National Laboratory, October 3-4, 1988) dealt with surfaces and kinetics, spectroscopy, small-angle scattering, diffraction, and topography and imaging. The primary objectives were to provide an educational resource for the chemistry community on the scientific research being conducted at existing synchrotron sources and to indicate some of the unique opportunities that will be made available with the Advanced Photon Source. The workshop organizers were also interested in gauging the interest of chemists in the field of synchrotron radiation. Interest expressed at the meeting has led to initial steps toward formation of a Chemistry Users Group at the APS. Individual projects are processed separately for the data bases.

Theory and modeling in nanoscience: Report of the May 10-11, 2002Workshop

Energy Technology Data Exchange (ETDEWEB)

McCurdy, C. William; Stechel, Ellen; Cummings, Peter; Hendrickson, Bruce; Keyes, David

2002-06-28

On May 10 and 11, 2002, a workshop entitled ''Theory and Modeling in Nanoscience'' was held in San Francisco, California, sponsored by the offices of Basic Energy Science and Advanced Scientific Computing Research of the Department of Energy. The Basic Energy Sciences Advisory Committee and the Advanced Scientific Computing Advisory Committee convened the workshop to identify challenges and opportunities for theory, modeling, and simulation in nanoscience and nanotechnology, and additionally to investigate the growing and promising role of applied mathematics and computer science in meeting those challenges. This report is the result of those contributions and the discussions at the workshop.

NATO Advanced Research Workshop on The Morphology and Dynamics of the Polar Cusp

CERN Document Server

Egeland, Alv

1985-01-01

These proceedings are based upon introductory talks, research reports and discussions from the NATO Advanced Workshop on the "Morphology and Dynamics of the Polar Cusp", held at Lillehammer, Norway, 7-12 May, 1984. The upper atmosphere at high latitudes is called the "Earth's win­ dow to outer space". Through various electrodynamic coupling process­ es as well as through direct transfer of particles many geophysical effects displayed there are direct manifestations of phenomena occurring in the deep space. The high latitude ionosphere will also exert a feedback on the regions of the magnetosphere and atmosphere to which it is coupled, acting as a momentum and energy source and sink, and a source of particles. Of particular interest are the sections of the near space known as the Polar Cusp. A vast portion of the earth's magnetic field envelope is electrically connected to these regions. This geometry results in a spatial mapping of the magnetospheric pro­ cesses and a focusing on to the ionosphere. In the ...

NATO Advanced Research Workshop on Painlevé Transcendents, their Asymptotics and Physical Applications

CERN Document Server

Winternitz, Pavel; Painlevé Transcendents, their Asymptotics and Physical Applications

1992-01-01

The NATO Advanced Research Workshop "Painleve Transcendents, their Asymp­ totics and Physical Applications", held at the Alpine Inn in Sainte-Adele, near Montreal, September 2 -7, 1990, brought together a group of experts to discuss the topic and produce this volume. There were 41 participants from 14 countries and 27 lectures were presented, all included in this volume. The speakers presented reviews of topics to which they themselves have made important contributions and also re­ sults of new original research. The result is a volume which, though multiauthored, has the character of a monograph on a single topic. This is the theory of nonlinear ordinary differential equations, the solutions of which have no movable singularities, other than poles, and the extension of this theory to partial differential equations. For short we shall call such systems "equations with the Painleve property". The search for such equations was a very topical mathematical problem in the 19th century. Early work concent...

Advanced Technologies for Robotic Exploration Leading to Human Exploration: Results from the SpaceOps 2015 Workshop

Science.gov (United States)

Lupisella, Mark L.; Mueller, Thomas

2016-01-01

This paper will provide a summary and analysis of the SpaceOps 2015 Workshop all-day session on "Advanced Technologies for Robotic Exploration, Leading to Human Exploration", held at Fucino Space Center, Italy on June 12th, 2015. The session was primarily intended to explore how robotic missions and robotics technologies more generally can help lead to human exploration missions. The session included a wide range of presentations that were roughly grouped into (1) broader background, conceptual, and high-level operations concepts presentations such as the International Space Exploration Coordination Group Roadmap, followed by (2) more detailed narrower presentations such as rover autonomy and communications. The broader presentations helped to provide context and specific technical hooks, and helped lay a foundation for the narrower presentations on more specific challenges and technologies, as well as for the discussion that followed. The discussion that followed the presentations touched on key questions, themes, actions and potential international collaboration opportunities. Some of the themes that were touched on were (1) multi-agent systems, (2) decentralized command and control, (3) autonomy, (4) low-latency teleoperations, (5) science operations, (6) communications, (7) technology pull vs. technology push, and (8) the roles and challenges of operations in early human architecture and mission concept formulation. A number of potential action items resulted from the workshop session, including: (1) using CCSDS as a further collaboration mechanism for human mission operations, (2) making further contact with subject matter experts, (3) initiating informal collaborative efforts to allow for rapid and efficient implementation, and (4) exploring how SpaceOps can support collaboration and information exchange with human exploration efforts. This paper will summarize the session and provide an overview of the above subjects as they emerged from the SpaceOps 2015

Proceedings of the 182nd basic science seminar (The workshop on neutron structural biology ) 'New frontiers of structural biology advanced by solution scattering'

International Nuclear Information System (INIS)

Fujiwara, Satoru

2001-03-01

182nd advanced science seminar (the workshop on neutron structural biology) was held in February 9-10, 2000 at Tokai. Thirty-six participants from universities, research institutes, and private companies took part in the workshop, and total of 24 lectures were given. This proceedings collects abstracts, the figures and tables, which the speakers used in their lectures. The proceedings contains two reviews from the point of view of x-ray and neutron scatterings, and six subjects (21 papers) including neutron and x-ray scattering in the era of structure genomics, structural changes detected with solution scattering, a new way in structural biology opened by neutron crystallography and neutron scattering, x-ray sources and detectors, simulation and solution scattering, and neutron sources and detectors. (Kazumata, Y.)

Executive Summary of the NHLBI Workshop Report: Leveraging Current Scientific Advancements to Understand Sarcoidosis Variability and Improve Outcomes.

Science.gov (United States)

Maier, Lisa A; Crouser, Elliott D; Martin, William J; Eu, Jerry

2017-12-01

Sarcoidosis is a systemic granulomatous disease that primarily affects the lung; it is associated with significant disparities, more commonly impacting those in the prime of their lives (age 20-50 yr, with a second peak after age 60 yr), black individuals, and women. However, the burden of disease, the ability to diagnose and prognose organ involvement and course, as well as specific treatment options, management options, and disease pathogenesis remain poorly understood. As a result, the National Heart, Lung, and Blood Institute undertook a sarcoidosis workshop, "Leveraging Current Scientific Advancements to Understand Sarcoidosis Variability and Improve Outcomes," to help address these issues by defining the scientific and clinical priorities to improve sarcoidosis care. The overarching recommendations from this workshop are outlined in the following summary and detailed in the accompanying articles. The recommendations included establishing collaborations and networks to conduct research based on consensus definitions of disease phenotypes and standards of care, and to provide clinical outreach to areas with a burden of disease to improve care. These collaborative networks would also serve as the hub to conduct clinical trials of devastating phenotypes (e.g., cardiac, neurologic, and fibrotic disease) not only for treatment but to enhance our understanding of the burden of disease. In addition, the networks would be used to leverage state-of-the-art "omics" and systems biology research, as well as other studies to advance understanding of disease pathogenesis, and development of biomarkers and therapeutic targets, with a goal to translate this information to improve care of individuals with sarcoidosis.

Machine Learning Technologies and Their Applications for Science and Engineering Domains Workshop -- Summary Report

Science.gov (United States)

Ambur, Manjula; Schwartz, Katherine G.; Mavris, Dimitri N.

2016-01-01

The fields of machine learning and big data analytics have made significant advances in recent years, which has created an environment where cross-fertilization of methods and collaborations can achieve previously unattainable outcomes. The Comprehensive Digital Transformation (CDT) Machine Learning and Big Data Analytics team planned a workshop at NASA Langley in August 2016 to unite leading experts the field of machine learning and NASA scientists and engineers. The primary goal for this workshop was to assess the state-of-the-art in this field, introduce these leading experts to the aerospace and science subject matter experts, and develop opportunities for collaboration. The workshop was held over a three day-period with lectures from 15 leading experts followed by significant interactive discussions. This report provides an overview of the 15 invited lectures and a summary of the key discussion topics that arose during both formal and informal discussion sections. Four key workshop themes were identified after the closure of the workshop and are also highlighted in the report. Furthermore, several workshop attendees provided their feedback on how they are already utilizing machine learning algorithms to advance their research, new methods they learned about during the workshop, and collaboration opportunities they identified during the workshop.

'A New World… Out of Nothing': Review of an interdisciplinary workshop

Directory of Open Access Journals (Sweden)

Francesca Iezzi

2017-04-01

Full Text Available The inter-disciplinary workshop, entitled 'A New World… Out of Nothing' took place at the University of Warwick during November 2016. This critical review will explore the rationale for the event and its features, drawing on the organiser's views on inter-disciplinarity and communicating pure mathematics to a wider audience. The workshop was organised by Francesca Iezzi, who has recently finished a PhD in pure Mathematics and is a fellow of the supporting institutions, the Warwick Institute for Advanced Study (IAS and the Warwick Institute for Advanced Teaching and Learning (IATL.

Summary of the Third International Planetary Dunes Workshop: remote sensing and image analysis of planetary dunes

Science.gov (United States)

Fenton, Lori K.; Hayward, Rosalyn K.; Horgan, Briony H.N.; Rubin, David M.; Titus, Timothy N.; Bishop, Mark A.; Burr, Devon M.; Chojnacki, Matthew; Dinwiddie, Cynthia L.; Kerber, Laura; Gall, Alice Le; Michaels, Timothy I.; Neakrase, Lynn D.V.; Newman, Claire E.; Tirsch, Daniela; Yizhaq, Hezi; Zimbelman, James R.

2013-01-01

The Third International Planetary Dunes Workshop took place in Flagstaff, AZ, USA during June 12–15, 2012. This meeting brought together a diverse group of researchers to discuss recent advances in terrestrial and planetary research on aeolian bedforms. The workshop included two and a half days of oral and poster presentations, as well as one formal (and one informal) full-day field trip. Similar to its predecessors, the presented work provided new insight on the morphology, dynamics, composition, and origin of aeolian bedforms on Venus, Earth, Mars, and Titan, with some intriguing speculation about potential aeolian processes on Triton (a satellite of Neptune) and Pluto. Major advancements since the previous International Planetary Dunes Workshop include the introduction of several new data analysis and numerical tools and utilization of low-cost field instruments (most notably the time-lapse camera). Most presentations represented advancement towards research priorities identified in both of the prior two workshops, although some previously recommended research approaches were not discussed. In addition, this workshop provided a forum for participants to discuss the uncertain future of the Planetary Aeolian Laboratory; subsequent actions taken as a result of the decisions made during the workshop may lead to an expansion of funding opportunities to use the facilities, as well as other improvements. The interactions during this workshop contributed to the success of the Third International Planetary Dunes Workshop, further developing our understanding of aeolian processes on the aeolian worlds of the Solar System.

Nineteenth Workshop Athens, GA, USA

CERN Document Server

Lewis, S P; Schöttler, H B; Computer Simulation Studies in Condensed-Matter Physics XIX

2008-01-01

This volume represents a "status report" emanating from presentations made during the 19th Annual Workshop on Computer Simulations Studies in Condensed Matter Physics at the Center for Simulational Physics at the University of Georgia in February, 2006. It provides a broad overview of the most recent advances in the field, spanning the range from equilibrium and non-equilibrium behavior in statistical physics to biological and soft condensed matter systems. Results on nanomagents and materials are included as are several descriptions of advances in methodology.

WWER-1000 reactor simulator. Workshop material

International Nuclear Information System (INIS)

2003-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series 12, 'Reactor Simulator Development' (2001). Course material for workshops using a pressurized water reactor (PWR) Simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication: Training Course Series No. 22 'Pressurized Water Reactor Simulator' (2003) and Training Course Series No. 23 'Boiling Water Reactor Simulator' (2003). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation. N. V. Tikhonov and S. B. Vygovsky of the Moscow Engineering and Physics Institute prepared this report for the IAEA

Bridging the Gap from Networking Technologies to Applications: Workshop Report

Science.gov (United States)

Johnson, Marjory J.; desJardins, Richard

2000-01-01

The objective of the Next Generation Internet (NGI) Federal program is threefold, encompassing development of networking technologies, high-performance network testbeds, and revolutionary applications. There have been notable advances in emerging network technologies and several nationwide testbeds have been established, but the integration of emerging technologies into applications is lagging. To help bridge this gap between developers of NGI networking technologies and developers of NGI applications, the NASA Research and Education Network (NREN) project hosted a two-day workshop at NASA Ames Research Center in August 1999. This paper presents a summary of the results of this workshop and also describes some of the challenges NREN is facing while incorporating new technologies into HPCC and other NASA applications. The workshop focused on three technologies - Quality of Service (QoS), advanced multicast, and security-and five major NGI application areas - telemedicine, digital earth, digital video, distributed data-intensive applications, and computational infrastructure applications. Network technology experts, application developers, and NGI testbed representatives came together at the workshop to promote cross-fertilization between the groups. Presentations on the first day, including an overview of the three technologies, application case studies and testbed status reports, laid the foundation for discussions on the second day. The objective of these latter discussions, held within smaller breakout groups, was to establish a coherent picture of the current status of the various pieces of each of the three technologies, to create a roadmap outlining future technology development, and to offer technological guidance to application developers. In this paper we first present a brief overview of the NGI applications that were represented at the workshop, focusing on the identification of technological advances that have successfully been incorporated in each

LogScope

Science.gov (United States)

Havelund, Klaus; Smith, Margaret H.; Barringer, Howard; Groce, Alex

2012-01-01

LogScope is a software package for analyzing log files. The intended use is for offline post-processing of such logs, after the execution of the system under test. LogScope can, however, in principle, also be used to monitor systems online during their execution. Logs are checked against requirements formulated as monitors expressed in a rule-based specification language. This language has similarities to a state machine language, but is more expressive, for example, in its handling of data parameters. The specification language is user friendly, simple, and yet expressive enough for many practical scenarios. The LogScope software was initially developed to specifically assist in testing JPL s Mars Science Laboratory (MSL) flight software, but it is very generic in nature and can be applied to any application that produces some form of logging information (which almost any software does).

Report of the workshop on Aviation Safety/Automation Program

Science.gov (United States)

Morello, Samuel A. (Editor)

1990-01-01

As part of NASA's responsibility to encourage and facilitate active exchange of information and ideas among members of the aviation community, an Aviation Safety/Automation workshop was organized and sponsored by the Flight Management Division of NASA Langley Research Center. The one-day workshop was held on October 10, 1989, at the Sheraton Beach Inn and Conference Center in Virginia Beach, Virginia. Participants were invited from industry, government, and universities to discuss critical questions and issues concerning the rapid introduction and utilization of advanced computer-based technology into the flight deck and air traffic controller workstation environments. The workshop was attended by approximately 30 discipline experts, automation and human factors researchers, and research and development managers. The goal of the workshop was to address major issues identified by the NASA Aviation Safety/Automation Program. Here, the results of the workshop are documented. The ideas, thoughts, and concepts were developed by the workshop participants. The findings, however, have been synthesized into a final report primarily by the NASA researchers.

Advances in Remote Sensing Approaches for Hazard Mitigation and Natural Resource Protection in Pacific Latin America: A Workshop for Advanced Graduate Students, Post- Doctoral Researchers, and Junior Faculty

Science.gov (United States)

Gierke, J. S.; Rose, W. I.; Waite, G. P.; Palma, J. L.; Gross, E. L.

2008-12-01

program in natural hazards (E-Haz). Advancements in research have been made, for example, in using thermal remote sensing methods for studying vent and eruptive processes, and in fusing RADARSAT with ASTER imagery to delineate lineaments in volcanic terrains for siting water wells. While these and other advancements are developed in conjunction with our foreign counterparts, the impacts of this work can be broadened through more comprehensive dissemination activities. Towards this end, we are in the planning phase of a Pan American workshop on applications of remote sensing techniques for natural hazards and water resources management. The workshop will be at least two weeks, sometime in July/August 2009, and involve 30-40 participants, with balanced participation from the U.S. and Latin America. In addition to fundamental aspects of remote sensing and digital image processing, the workshop topics will be presented in the context of new developments for studying volcanic processes and hazards and for characterizing groundwater systems.

10th Workshop on Crystalline Silicon Solar Cell Materials and Processes: Extended Abstracts and Papers from the Workshop, Copper Mountain Resort; August 14-16, 2000

Energy Technology Data Exchange (ETDEWEB)

Sopori, B.L.; Gee, J.; Kalejs, J.; Saitoh, R.; Stavola, M.; Swanson, D.; Tan, T.; Weber, E.; Werner, J.

2000-08-11

The 10th Workshop provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and non-photovoltaic fields. Discussions included the various aspects of impurities and defects in silicon-their properties, the dynamics during device processing, and their application for developing low-cost processes for manufacturing high-efficiency silicon solar cells. Sessions and panel discussions also reviewed thin-film crystalline-silicon PV, advanced cell structures, new processes and process characterization techniques, and future manufacturing requirements to meet the ambitious expansion goals described in the recently released US PV Industry Roadmap. The Workshop also provided an excellent opportunity for researchers in private industry and at universities to recognize a mutual need for future collaborative research. The three-day workshop consisted of presentations by invited speakers, followed by discussion sessions. In addition, there was two poster sessions presenting the latest research and development results. The subjects discussed included: solar cell processing, light-induced degradation, gettering and passivation, crystalline silicon growth, thin-film silicon solar cells, and impurities and defects. Two special sessions featured at this workshop: advanced metallization and interconnections, and characterization methods.

CyberGIS - Toward synergistic advancement of cyberinfrastructure and GIScience: A workshop summary

Directory of Open Access Journals (Sweden)

Shaowen Wang

2012-06-01

Full Text Available This community activity report describes the outcomes of a CyberGIS workshop, held in conjunction with the UCGIS 2010 annual winter meeting and sponsored by the National Science Foundation (NSF Office of Cyberinfrastructure. Over the one and one-half day workshop, a multidisciplinary group of experts from the international communities of cyberinfrastructure, GIScience, spatial analysis and modeling, and several other related scientific domains were brought together for a participatory meeting composed of both small- and large-group settings and to discuss the CyberGIS road map.

Mars exploration study workshop 2

Science.gov (United States)

Duke, Michael B.; Budden, Nancy Ann

1993-11-01

A year-long NASA-wide study effort has led to the development of an innovative strategy for the human exploration of Mars. The latest Mars Exploration Study Workshop 2 advanced a design reference mission (DRM) that significantly reduces the perceived high costs, complex infrastructure, and long schedules associated with previous Mars scenarios. This surface-oriented philosophy emphasizes the development of high-leveraging surface technologies in lieu of concentrating exclusively on space transportation technologies and development strategies. As a result of the DRM's balanced approach to mission and crew risk, element commonality, and technology development, human missions to Mars can be accomplished without the need for complex assembly operations in low-Earth orbit. This report, which summarizes the Mars Exploration Study Workshop held at the Ames Research Center on May 24-25, 1993, provides an overview of the status of the Mars Exploration Study, material presented at the workshop, and discussions of open items being addressed by the study team. The workshop assembled three teams of experts to discuss cost, dual-use technology, and international involvement, and to generate a working group white paper addressing these issues. The three position papers which were generated are included in section three of this publication.

Dynamic Planar Convex Hull with Optimal Query Time and O(log n · log log n ) Update Time

DEFF Research Database (Denmark)

Brodal, Gerth Stølting; Jakob, Riko

2000-01-01

The dynamic maintenance of the convex hull of a set of points in the plane is one of the most important problems in computational geometry. We present a data structure supporting point insertions in amortized O(log n · log log log n) time, point deletions in amortized O(log n · log log n) time......, and various queries about the convex hull in optimal O(log n) worst-case time. The data structure requires O(n) space. Applications of the new dynamic convex hull data structure are improved deterministic algorithms for the k-level problem and the red-blue segment intersection problem where all red and all...

The 13th International Workshop on Targetry and Target Chemistry Proceedings

DEFF Research Database (Denmark)

Haroun, Samar; Givskov, Alex David; Jensen, Mikael

in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal......This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risø National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production...... of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring...

Compact X-ray Light Source Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Thevuthasan, Suntharampillai; Evans, James E.; Terminello, Louis J.; Koppenaal, David W.; Manke, Kristin L.; Plata, Charity

2012-12-01

This report, produced jointly by EMSL and FCSD, is the result of a workshop held in September 2011 that examined the utility of a compact x-ray light source (CXLS) in addressing many scientific challenges critical to advancing energy science and technology.

Teaching Scenario-Based Planning for Sustainable Landscape Development: An Evaluation of Learning Effects in the Cagliari Studio Workshop

Directory of Open Access Journals (Sweden)

Christian Albert

2015-05-01

Full Text Available This paper investigates the contributions of an intensive educational workshop to advance students’ understanding and skills for collaborative, scenario-based landscape planning. The research design involves a case study workshop with thirty international students and several regional experts as well as a multi-stage, in-process evaluation. The workshop resulted in six different alternative futures for the region of Cagliari, Italy, and a seventh combined version that was considered best by regional reviewers. The students’ learning evaluation showed substantial advances in their relevant understanding and skills. Key aspects of the workshop pedagogy and the evaluation are discussed, and recommendations for future applications presented.

Estimating two indirect logging costs caused by accelerated erosion.

Science.gov (United States)

Glen O. Klock

1976-01-01

In forest areas where high soil erosion potential exists, a comparative yarding cost estimate, including the indirect costs determined by methods proposed here, shows that the total cost of using "advanced" logging methods may be less than that of "traditional" systems.

Hardwood log grades and lumber grade yields for factory lumber logs

Science.gov (United States)

Leland F. Hanks; Glenn L. Gammon; Robert L. Brisbin; Everette D. Rast

1980-01-01

The USDA Forest Service Standard Grades for Hardwood Factory Lumber Logs are described, and lumber grade yields for 16 species and 2 species groups are presented by log grade and log diameter. The grades enable foresters, log buyers, and log sellers to select and grade those log suitable for conversion into standard factory grade lumber. By using the apropriate lumber...

Pressurized water reactor simulator. Workshop material. 2. ed

International Nuclear Information System (INIS)

2005-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development. And the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA Training Course Series No. 12, 'Reactor Simulator Development' (2001). Course material for workshops using a WWER- 1000 reactor department simulator from the Moscow Engineering and Physics Institute, the Russian Federation is presented in the IAEA Training Course Series No. 21, 2nd edition, 'WWER-1000 Reactor Simulator' (2005). Course material for workshops using a boiling water reactor simulator developed for the IAEA by Cassiopeia Technologies Incorporated of Canada (CTI) is presented in the IAEA publication: Training Course Series No.23, 2nd edition, 'Boiling Water Reactor Simulator' (2005). This report consists of course material for workshops using a pressurized water reactor simulator

Gulf of Mexico Gas Hydrate Joint Industry Project Leg II logging-while-drilling data acquisition and analysis

Science.gov (United States)

Collett, Timothy S.; Lee, Wyung W.; Zyrianova, Margarita V.; Mrozewski, Stefan A.; Guerin, Gilles; Cook, Ann E.; Goldberg, Dave S.

2012-01-01

One of the objectives of the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II (GOM JIP Leg II) was the collection of a comprehensive suite of logging-while-drilling (LWD) data within gas-hydrate-bearing sand reservoirs in order to make accurate estimates of the concentration of gas hydrates under various geologic conditions and to understand the geologic controls on the occurrence of gas hydrate at each of the sites drilled during this expedition. The LWD sensors just above the drill bit provided important information on the nature of the sediments and the occurrence of gas hydrate. There has been significant advancements in the use of downhole well-logging tools to acquire detailed information on the occurrence of gas hydrate in nature: From using electrical resistivity and acoustic logs to identify gas hydrate occurrences in wells to where wireline and advanced logging-while-drilling tools are routinely used to examine the petrophysical nature of gas hydrate reservoirs and the distribution and concentration of gas hydrates within various complex reservoir systems. Recent integrated sediment coring and well-log studies have confirmed that electrical resistivity and acoustic velocity data can yield accurate gas hydrate saturations in sediment grain supported (isotropic) systems such as sand reservoirs, but more advanced log analysis models are required to characterize gas hydrate in fractured (anisotropic) reservoir systems. In support of the GOM JIP Leg II effort, well-log data montages have been compiled and presented in this report which includes downhole logs obtained from all seven wells drilled during this expedition with a focus on identifying and characterizing the potential gas-hydrate-bearing sedimentary section in each of the wells. Also presented and reviewed in this report are the gas-hydrate saturation and sediment porosity logs for each of the wells as calculated from available downhole well logs.

Gulf of Mexico Gas Hydrate Joint Industry Project Leg II logging-while-drilling data acquisition and anaylsis

Science.gov (United States)

Collett, Timothy S.; Lee, Myung W.; Zyrianova, Margarita V.; Mrozewski, Stefan A.; Guerin, Gilles; Cook, Ann E.; Goldberg, Dave S.

2012-01-01

One of the objectives of the Gulf of MexicoGasHydrateJointIndustryProjectLegII (GOM JIP LegII) was the collection of a comprehensive suite of logging-while-drilling (LWD) data within gas-hydrate-bearing sand reservoirs in order to make accurate estimates of the concentration of gashydrates under various geologic conditions and to understand the geologic controls on the occurrence of gashydrate at each of the sites drilled during this expedition. The LWD sensors just above the drill bit provided important information on the nature of the sediments and the occurrence of gashydrate. There has been significant advancements in the use of downhole well-logging tools to acquire detailed information on the occurrence of gashydrate in nature: From using electrical resistivity and acoustic logs to identify gashydrate occurrences in wells to where wireline and advanced logging-while-drilling tools are routinely used to examine the petrophysical nature of gashydrate reservoirs and the distribution and concentration of gashydrates within various complex reservoir systems. Recent integrated sediment coring and well-log studies have confirmed that electrical resistivity and acoustic velocity data can yield accurate gashydrate saturations in sediment grain supported (isotropic) systems such as sand reservoirs, but more advanced log analysis models are required to characterize gashydrate in fractured (anisotropic) reservoir systems. In support of the GOM JIP LegII effort, well-log data montages have been compiled and presented in this report which includes downhole logs obtained from all seven wells drilled during this expedition with a focus on identifying and characterizing the potential gas-hydrate-bearing sedimentary section in each of the wells. Also presented and reviewed in this report are the gas-hydrate saturation and sediment porosity logs for each of the wells as calculated from available downhole well logs.

1993 DOE technical standards managers workshop: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

This workshop is focused on the benefits of the DOE technical standards program, which is focused toward the preferred use of non-Government standards for DOE activities and the development of DOE technical standards when non-Government standards are not available or are inappropriate. One goal of the program is to replace redundant site-specific standards with more universally accepted documents that have been scrutinized by experts. This replacement is discussed at the workshop along with the problems encountered and solutions found. The workshop provided an opportunity for geographically dispersed people to meet and advance their standards knowledge and efforts to support the program. Safety issues have been the driving force behind the program to date. Several companies offer products and services that support the development, processing, and retrieval of standards. This document mostly comprise vugraphs.

Cyber terrorism prevention and counteraction workshop review

NARCIS (Netherlands)

Pastukhov, O.M.

2011-01-01

A NATO Advanced Training Course (ATC ) on Cyber Terrorism Prevention and Counteraction workshop, held in Kiev on September 27-29, 2010, allowed the participants to share their experiences with experts from Ukraine, a Partnership for Peace country. The participants exchanged their ideas on the ways

Advanced Learning Technologies and Learning Networks and Their Impact on Future Aerospace Workforce

Science.gov (United States)

Noor, Ahmed K. (Compiler)

2003-01-01

This document contains the proceedings of the training workshop on Advanced Learning Technologies and Learning Networks and their impact on Future Aerospace Workforce. The workshop was held at the Peninsula Workforce Development Center, Hampton, Virginia, April 2 3, 2003. The workshop was jointly sponsored by Old Dominion University and NASA. Workshop attendees came from NASA, other government agencies, industry, and universities. The objectives of the workshop were to: 1) provide broad overviews of the diverse activities related to advanced learning technologies and learning environments, and 2) identify future directions for research that have high potential for aerospace workforce development. Eighteen half-hour overviewtype presentations were made at the workshop.

ASCR Cybersecurity for Scientific Computing Integrity - Research Pathways and Ideas Workshop

Energy Technology Data Exchange (ETDEWEB)

Peisert, Sean [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Univ. of California, Davis, CA (United States); Potok, Thomas E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jones, Todd [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-06-03

At the request of the U.S. Department of Energy's (DOE) Office of Science (SC) Advanced Scientific Computing Research (ASCR) program office, a workshop was held June 2-3, 2015, in Gaithersburg, MD, to identify potential long term (10 to +20 year) cybersecurity fundamental basic research and development challenges, strategies and roadmap facing future high performance computing (HPC), networks, data centers, and extreme-scale scientific user facilities. This workshop was a follow-on to the workshop held January 7-9, 2015, in Rockville, MD, that examined higher level ideas about scientific computing integrity specific to the mission of the DOE Office of Science. Issues included research computation and simulation that takes place on ASCR computing facilities and networks, as well as network-connected scientific instruments, such as those run by various DOE Office of Science programs. Workshop participants included researchers and operational staff from DOE national laboratories, as well as academic researchers and industry experts. Participants were selected based on the submission of abstracts relating to the topics discussed in the previous workshop report [1] and also from other ASCR reports, including "Abstract Machine Models and Proxy Architectures for Exascale Computing" [27], the DOE "Preliminary Conceptual Design for an Exascale Computing Initiative" [28], and the January 2015 machine learning workshop [29]. The workshop was also attended by several observers from DOE and other government agencies. The workshop was divided into three topic areas: (1) Trustworthy Supercomputing, (2) Extreme-Scale Data, Knowledge, and Analytics for Understanding and Improving Cybersecurity, and (3) Trust within High-end Networking and Data Centers. Participants were divided into three corresponding teams based on the category of their abstracts. The workshop began with a series of talks from the program manager and workshop chair, followed by the leaders for each of the

Proceedings of the 182nd basic science seminar (The workshop on neutron structural biology ) 'New frontiers of structural biology advanced by solution scattering'

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, Satoru (ed.) [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-03-01

182nd advanced science seminar (the workshop on neutron structural biology) was held in February 9-10, 2000 at Tokai. Thirty-six participants from universities, research institutes, and private companies took part in the workshop, and total of 24 lectures were given. This proceedings collects abstracts, the figures and tables, which the speakers used in their lectures. The proceedings contains two reviews from the point of view of x-ray and neutron scatterings, and six subjects (21 papers) including neutron and x-ray scattering in the era of structure genomics, structural changes detected with solution scattering, a new way in structural biology opened by neutron crystallography and neutron scattering, x-ray sources and detectors, simulation and solution scattering, and neutron sources and detectors. (Kazumata, Y.)

Logging Concessions Enable Illegal Logging Crisis in the Peruvian Amazon

OpenAIRE

Finer, Matt; Jenkins, Clinton N.; Sky, Melissa A. Blue; Pine, Justin

2014-01-01

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US?Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3%...

Summary of the Workshop on Neutron Cross Section Covariances

International Nuclear Information System (INIS)

Smith, Donald L.

2008-01-01

A Workshop on Neutron Cross Section Covariances was held from June 24-27, 2008, in Port Jefferson, New York. This Workshop was organized by the National Nuclear Data Center, Brookhaven National Laboratory, to provide a forum for reporting on the status of the growing field of neutron cross section covariances for applications and for discussing future directions of the work in this field. The Workshop focused on the following four major topical areas: covariance methodology, recent covariance evaluations, covariance applications, and user perspectives. Attention was given to the entire spectrum of neutron cross section covariance concerns ranging from light nuclei to the actinides, and from the thermal energy region to 20 MeV. The papers presented at this conference explored topics ranging from fundamental nuclear physics concerns to very specific applications in advanced reactor design and nuclear criticality safety. This paper provides a summary of this workshop. Brief comments on the highlights of each Workshop contribution are provided. In addition, a perspective on the achievements and shortcomings of the Workshop as well as on the future direction of research in this field is offered

Proceedings of the fifteenth international workshop on ceramic breeder blanket interactions

International Nuclear Information System (INIS)

Tanigawa, Hisashi; Enoeda, Mikio

2010-03-01

This report is the Proceedings of 'the Fifteenth International Workshop on Ceramic Breeder Blanket Interactions' which was held as a workshop on ceramic breeders Under the IEA Implementing Agreement on the Nuclear Technology of Fusion Reactors. This workshop was held in Sapporo, Japan on 3-4, Sept. 2009. Twenty six participants from EU, Japan, India, Russia and USA attended the workshop. The scope of the workshop included 1) evolutions in ceramic breeder blanket design, 2) progress in ceramic breeder material development, 3) irradiation testing, 4) breeder material properties, 5) out-of-pile pebble bed experiment, 6) modeling of the thermal, mechanical and tritium transfer behavior of pebble beds and 7) interfacing issues of solid breeder blanket development. By this workshop, advance of key technologies for solid breeder blanket development was shared among the participants. Also, desired direction of further investigation and development was recognized. The 20 of the presented papers are indexed individually. (J.P.N.)

Proceedings of the fifteenth international workshop on ceramic breeder blanket interactions

Energy Technology Data Exchange (ETDEWEB)

Tanigawa, Hisashi; Enoeda, Mikio [Japan Atomic Energy Agency, Fusion Research and Development Directorate, Naka, Ibaraki (Japan)

2010-03-15

This report is the Proceedings of 'the Fifteenth International Workshop on Ceramic Breeder Blanket Interactions' which was held as a workshop on ceramic breeders Under the IEA Implementing Agreement on the Nuclear Technology of Fusion Reactors. This workshop was held in Sapporo, Japan on 3-4, Sept. 2009. Twenty six participants from EU, Japan, India, Russia and USA attended the workshop. The scope of the workshop included 1) evolutions in ceramic breeder blanket design, 2) progress in ceramic breeder material development, 3) irradiation testing, 4) breeder material properties, 5) out-of-pile pebble bed experiment, 6) modeling of the thermal, mechanical and tritium transfer behavior of pebble beds and 7) interfacing issues of solid breeder blanket development. By this workshop, advance of key technologies for solid breeder blanket development was shared among the participants. Also, desired direction of further investigation and development was recognized. The 20 of the presented papers are indexed individually. (J.P.N.)

Geophysical logging for mineral exploration and development

International Nuclear Information System (INIS)

Plouffe, R.D.

1981-01-01

It is possible to retrieve from small-diameter holes geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eU 3 O 8 values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today's technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or in-situ assaying, and the use of multiple logs for better lithological and physical rock property determinations. (auth)

Proceedings of the Advanced Hadron Facility accelerator design workshop, February 20--25, 1989

International Nuclear Information System (INIS)

Thiessen, H.A.

1990-04-01

The International Workshop on Hadron Facility Technology was held February 20--25, 1989, at the Study Center at Los Alamos National Laboratory. This volume (first of two) included papers on architecture, beam diagnostics, compressors, and linacs. Participants included groups from AHF, Brookhaven National Laboratory, European Hadron Facility, Fermilab, and the Moscow Meson Factory. The workshop was well attended by members of the Los Alamos staff. The interchange of information and the opportunity by criticism by peers was important to all who attended

Report from the 2nd Workshop on Extremely Large Databases

Directory of Open Access Journals (Sweden)

Jacek Becla

2009-03-01

Full Text Available The complexity and sophistication of large scale analytics in science and industry have advanced dramatically in recent years. Analysts are struggling to use complex techniques such as time series analysis and classification algorithms because their familiar, powerful tools are not scalable and cannot effectively use scalable database systems. The 2nd Extremely Large Databases (XLDB workshop was organized to understand these issues, examine their implications, and brainstorm possible solutions. The design of a new open source science database, SciDB that emerged from the first workshop in this series was also debated. This paper is the final report of the discussions and activities at this workshop.

IAEA workshop on 'Atomic and molecular data for fusion energy research'. Summary report

International Nuclear Information System (INIS)

Clark, R.E.H.

2004-05-01

On September 8-12 a workshop on Atomic and Molecular (A+M) Data for Fusion Energy Research was hosted by the International Centre for Theoretical Physics in Trieste Italy. The workshop was attended by twelve students representing eleven Member States. A total of five lecturers, including four external to the Agency, made presentations to the workshop. All lecturers provided advance copies of the lecture materials and all provided written assignments for the students, to provide practical examples of applications of data issues to actual problems related to fusion energy research. All materials were collected on CDs, which were distributed to the students by the conclusion of the workshop. During the course of the workshop the students were given the opportunity to describe their backgrounds and research interests. The workshop did arouse interest in A+M processes related to fusion. The workshop was viewed as successful by the students. (author)

Executive summary. Summary of the workshop sessions

International Nuclear Information System (INIS)

2012-01-01

The workshop played a great role in sharing the current state-of-the art on the PSA (Probabilistic Safety Assessment) of new and advanced reactors, and points of interest among member countries. The major concern expressed by the participants included passive safety system reliability, digital system reliability, new and advanced reactors-specific risk assessment methodology and relevant computational tool, and safety-security interface, etc). Main findings obtained from the workshop are as follows. For new reactors, the role of PSA is more important and more formalized comparing with exiting reactors. The PSAs are being used in the design of new reactors for purposes such as balance between accident prevention and mitigation features of the design, demonstration of safety, identification of design vulnerabilities and improvements, and comparison with the risk of existing plants, etc. For advanced reactors, the role of PSA is also being regarded as an essential tool for safety improvement and comparison of reactor designs at the conceptual or preliminary stages, but their practical use is at the early stage to gain the insights of risk into these reactors. This is due to the fact that the use of PSA for advanced reactors is mainly focused on identifying the PSA issues for designer and regulatory bodies, and developing the relevant methodologies and tools. Better guidance and peer review process on the PSA of new and advanced reactors was identified by both industry and regulatory as an important aspect

http Log Analysis

DEFF Research Database (Denmark)

Bøving, Kristian Billeskov; Simonsen, Jesper

2004-01-01

This article documents how log analysis can inform qualitative studies concerning the usage of web-based information systems (WIS). No prior research has used http log files as data to study collaboration between multiple users in organisational settings. We investigate how to perform http log...... analysis; what http log analysis says about the nature of collaborative WIS use; and how results from http log analysis may support other data collection methods such as surveys, interviews, and observation. The analysis of log files initially lends itself to research designs, which serve to test...... hypotheses using a quantitative methodology. We show that http log analysis can also be valuable in qualitative research such as case studies. The results from http log analysis can be triangulated with other data sources and for example serve as a means of supporting the interpretation of interview data...

Characterization of reservoir fractures using conventional geophysical logging

Directory of Open Access Journals (Sweden)

Paitoon Laongsakul

2011-04-01

Full Text Available In hydrocarbon exploration fractures play an important role as possible pathways for the hydrocarbon flow and bythis enhancing the overall formation’s permeability. Advanced logging methods for fracture analysis, like the boreholeacoustic televiewer and Formation Microscanner (FMS are available, but these are additional and expensive tools. However,open and with water or hydrocarbon filled fractures are also sensitive to electrical and other conventional logging methods.For this study conventional logging data (electric, seismic, etc were available plus additional fracture information from FMS.Taking into account the borehole environment the results show that the micro-spherically focused log indicates fractures byshowing low resistivity spikes opposite open fractures, and high resistivity spikes opposite sealed ones. Compressional andshear wave velocities are reduced when passing trough the fracture zone, which are assumed to be more or less perpendicularto borehole axis. The photoelectric absorption curve exhibit a very sharp peak in front of a fracture filled with bariteloaded mud cake. The density log shows low density spikes that are not seen by the neutron log, usually where fractures,large vugs, or caverns exist. Borehole breakouts can cause a similar effect on the logging response than fractures, but fracturesare often present when this occurs. The fracture index calculation by using threshold and input weight was calculatedand there was in general a good agreement with the fracture data from FMS especially in fracture zones, which mainlycontribute to the hydraulic system of the reservoir. Finally, the overall results from this study using one well are promising,however further research in the combination of different tools for fracture identification is recommended as well as the useof core for further validation.

From Workshop to Classroom: Bridging GIS Success

Science.gov (United States)

Stonier, Francis; Hong, Jung Eun

2016-01-01

This article shares the first-time geographic information system (GIS) experiences of two advanced placement human geography classes. The teacher had participated in a summer GIS workshop and then brought those skills into her classroom for the students' benefit. Eighteen students shared their experiences researching their family history, working…

Advanced nuclear reactor safety issues and research needs

International Nuclear Information System (INIS)

2002-01-01

On 18-20 February 2002, the OECD Nuclear Energy Agency (NEA) organised, with the co-sponsorship of the International Atomic Energy Agency (IAEA) and in collaboration with the European Commission (EC), a Workshop on Advanced Nuclear Reactor Safety Issues and Research Needs. Currently, advanced nuclear reactor projects range from the development of evolutionary and advanced light water reactor (LWR) designs to initial work to develop even further advanced designs which go beyond LWR technology (e.g. high-temperature gas-cooled reactors and liquid metal-cooled reactors). These advanced designs include a greater use of advanced technology and safety features than those employed in currently operating plants or approved designs. The objectives of the workshop were to: - facilitate early identification and resolution of safety issues by developing a consensus among participating countries on the identification of safety issues, the scope of research needed to address these issues and a potential approach to their resolution; - promote the preservation of knowledge and expertise on advanced reactor technology; - provide input to the Generation IV International Forum Technology Road-map. In addition, the workshop tried to link advancement of knowledge and understanding of advanced designs to the regulatory process, with emphasis on building public confidence. It also helped to document current views on advanced reactor safety and technology, thereby contributing to preserving knowledge and expertise before it is lost. (author)

Cryogenics Vision Workshop for High-Temperature Superconducting Electric Power Systems Proceedings

International Nuclear Information System (INIS)

Energetics, Inc.

2000-01-01

The US Department of Energy's Superconductivity Program for Electric Systems sponsored the Cryogenics Vision Workshop, which was held on July 27, 1999 in Washington, D.C. This workshop was held in conjunction with the Program's Annual Peer Review meeting. Of the 175 people attending the peer review meeting, 31 were selected in advance to participate in the Cryogenics Vision Workshops discussions. The participants represented cryogenic equipment manufactures, industrial gas manufacturers and distributors, component suppliers, electric power equipment manufacturers (Superconductivity Partnership Initiative participants), electric utilities, federal agencies, national laboratories, and consulting firms. Critical factors were discussed that need to be considered in describing the successful future commercialization of cryogenic systems. Such systems will enable the widespread deployment of high-temperature superconducting (HTS) electric power equipment. Potential research, development, and demonstration (RD and D) activities and partnership opportunities for advancing suitable cryogenic systems were also discussed. The workshop agenda can be found in the following section of this report. Facilitated sessions were held to discuss the following specific focus topics: identifying Critical Factors that need to be included in a Cryogenics Vision for HTS Electric Power Systems (From the HTS equipment end-user perspective) identifying R and D Needs and Partnership Roles (From the cryogenic industry perspective) The findings of the facilitated Cryogenics Vision Workshop were then presented in a plenary session of the Annual Peer Review Meeting. Approximately 120 attendees participated in the afternoon plenary session. This large group heard summary reports from the workshop session leaders and then held a wrap-up session to discuss the findings, cross-cutting themes, and next steps. These summary reports are presented in this document. The ideas and suggestions raised during

Log quality enhancement: A systematic assessment of logging company wellsite performance and log quality

International Nuclear Information System (INIS)

Farnan, R.A.; Mc Hattie, C.M.

1984-01-01

To improve the monitoring of logging company performance, computer programs were developed to assess information en masse from log quality check lists completed on wellsite by the service company engineer and Phillips representative. A study of all logging jobs performed by different service companies for Phillips in Oklahoma (panhandle excepted) during 1982 enabled several pertinent and beneficial interpretations to be made. Company A provided the best tool and crew service. Company B incurred an excessive amount of lost time related to tool failure, in particular the neutron-density tool combination. Company C, although used only three times, incurred no lost time. With a reasonable data base valid conclusions were made pertaining, for example, to repeated tool malfunctions. The actual logs were then assessed for quality

Advances in 4D treatment planning for scanned particle beam therapy - report of dedicated workshops

NARCIS (Netherlands)

Bert, Christoph; Graeff, Christian; Riboldi, Marco; Nill, Simeon; Baroni, Guido; Knopf, Antje-Christin

2014-01-01

We report on recent progress in the field of mobile tumor treatment with scanned particle beams, as discussed in the latest editions of the 4D treatment planning workshop. The workshop series started in 2009, with about 20 people from 4 research institutes involved, all actively working on particle

Workshop on translating Science to Clinics and Market

OpenAIRE

Editor

2016-01-01

The workshop on translating technology is directed to senior industry leaders High tech entrepreneurs Scientists from academia and industry Clinical researchers and Venture capitalists. The event will cover various topics including startup success stories 19 inspiring showcases about advanced drug delivery systems.

WORKSHOP: Crystalline beams

International Nuclear Information System (INIS)

Anon.

1989-01-01

Following pioneer work by specialists at the Soviet Novosibirsk Laboratory some ten years ago, interest developed in the possibility of 'freezing' ion beams in storage rings by pushing cooling (to smooth out beam behaviour) to its limits, the final goal being to lock the ions into a neat crystal pattern. After advances by groups working on laser cooled ions in traps, and with several cooling rings now in operation, a workshop on crystalline ion beams was organized recently by the GSI (Darmstadt) Laboratory and held at Wertheim in Germany

Proceedings of the Advanced Hadron Facility accelerator design workshop, February 20--25, 1989

International Nuclear Information System (INIS)

Thiessen, H.A.

1990-04-01

The International Workshop on Hadron Facility Technology was held February 20--25, 1989, at the Study Center at Los Alamos National Laboratory. This volume (second of two) included papers on computer controls, polarized beam, rf, magnet and power supplies, experimental areas, and instabilities. Participants included groups from AHF, Brookhaven National Laboratory, European Hadron Facility, Fermilab, and the Moscow Meson Factory. The workshop was well attended by members of the Los Alamos staff. The interchange of information and the opportunity by criticism by peers was important to all who attended

Transport Task Force workshop: basic experiments highlights

Energy Technology Data Exchange (ETDEWEB)

Linford, R.K. (Los Alamos National Lab., NM (USA)); Luckhardt, S. (Massachusetts Inst. of Tech., Cambridge, MA (USA)); Lyon, J.F. (Oak Ridge National Lab., TN (USA)); Navratil, G.A. (Columbia Univ., New York, NY (USA)); Schoenberg, K.F. (Los Alamos National Lab., NM (USA))

1990-01-01

Selected topics are summarized from the Basic Experiments session of the Transport Task Force Workshop held August 21-24, 1989, in San Diego, California. This session included presentations on paradigm experiments, stellarators, reversed-field pinches, and advanced tokamaks. Recent advances in all of these areas illustrate the importance of these experiments in advancing our understanding of toroidal transport. Progress has been made in measuring the details of particle diffusion, isolating specific modes, measuring fluctuation variations with field geometry and beta, and comparing all these with theoretical predictions. The development of experimental tools for determining which fluctuations dominate transport are also reported. Continued significant advances are anticipated in a number of areas highlighted. (author).

Transport Task Force workshop: basic experiments highlights

International Nuclear Information System (INIS)

Linford, R.K.; Luckhardt, S.; Lyon, J.F.; Navratil, G.A.; Schoenberg, K.F.

1990-01-01

Selected topics are summarized from the Basic Experiments session of the Transport Task Force Workshop held August 21-24, 1989, in San Diego, California. This session included presentations on paradigm experiments, stellarators, reversed-field pinches, and advanced tokamaks. Recent advances in all of these areas illustrate the importance of these experiments in advancing our understanding of toroidal transport. Progress has been made in measuring the details of particle diffusion, isolating specific modes, measuring fluctuation variations with field geometry and beta, and comparing all these with theoretical predictions. The development of experimental tools for determining which fluctuations dominate transport are also reported. Continued significant advances are anticipated in a number of areas highlighted. (author)

1st Advanced Marine Renewable Energy Instrumentation Experts Workshop: April 5-7, 2011

International Nuclear Information System (INIS)

2011-01-01

The U.S. marine energy industry is actively pursuing development of offshore wind and marine hydrokinetic (MHK) energy systems. Experience in the wind energy sector demonstrates that new technology development requires thorough measurement and characterization of the environmental conditions prevalent at installation sites and of technology operating in the field. Presently, there are no turn-key instrumentation system solutions that meet the measurement needs of the marine energy industry. The 1st Advanced Marine Renewable Energy Instrumentation Experts Workshop brought together technical experts from government laboratories, academia, and industry representatives from marine energy, wind, offshore oil and gas, and instrumentation developers to present and discuss the instrumentation needs of the marine energy industry. The goals of the meeting were to: (1) Share the latest relevant knowledge among technical experts; (2) Review relevant state-of-the-art field measurement technologies and methods; (3) Review lessons learned from recent field deployments; (4) Identify synergies across different industries; (5) Identify gaps between existing and needed instrumentation capabilities; (6) Understand who are the leading experts; (7) Provide a forum where stakeholders from the marine energy industry could provide substantive input in the development of new marine energy field deployable instrumentation packages.

1st Advanced Marine Renewable Energy Instrumentation Experts Workshop: April 5-7, 2011

Energy Technology Data Exchange (ETDEWEB)

2011-10-01

The U.S. marine energy industry is actively pursuing development of offshore wind and marine hydrokinetic (MHK) energy systems. Experience in the wind energy sector demonstrates that new technology development requires thorough measurement and characterization of the environmental conditions prevalent at installation sites and of technology operating in the field. Presently, there are no turn-key instrumentation system solutions that meet the measurement needs of the marine energy industry. The 1st Advanced Marine Renewable Energy Instrumentation Experts Workshop brought together technical experts from government laboratories, academia, and industry representatives from marine energy, wind, offshore oil and gas, and instrumentation developers to present and discuss the instrumentation needs of the marine energy industry. The goals of the meeting were to: (1) Share the latest relevant knowledge among technical experts; (2) Review relevant state-of-the-art field measurement technologies and methods; (3) Review lessons learned from recent field deployments; (4) Identify synergies across different industries; (5) Identify gaps between existing and needed instrumentation capabilities; (6) Understand who are the leading experts; (7) Provide a forum where stakeholders from the marine energy industry could provide substantive input in the development of new marine energy field deployable instrumentation packages.

Log N-log S in inconclusive

Science.gov (United States)

Klebesadel, R. W.; Fenimore, E. E.; Laros, J.

1983-01-01

The log N-log S data acquired by the Pioneer Venus Orbiter Gamma Burst Detector (PVO) are presented and compared to similar data from the Soviet KONUS experiment. Although the PVO data are consistent with and suggestive of a -3/2 power law distribution, the results are not adequate at this state of observations to differentiate between a -3/2 and a -1 power law slope.

Report on the international workshop on next generation linear colliders

International Nuclear Information System (INIS)

Ruth, R.D.

1989-05-01

Many laboratories around the world have begun vigorous research programs on a next generation linear collider (NLC). However, it has been recognized that the research towards NLC is beyond the capabilities of any one laboratory presently. This workshop was organized to begin a series of workshops that address this problem. Specifically, the main goals of the workshop were to discuss research programs of the various laboratories around the world, to identify common areas of interest in the various NLC designs, and finally to advance these programs by collaboration. The particular topics discussed briefly in this paper are: parameters, rf power, structures, final focus, beam dynamics, damping rings, and instrumentation. 2 refs., 3 figs., 6 tabs

NATO Advanced Research Workshop on The Design of Mathematical Modelling Courses for Engineering Education

CERN Document Server

Moscardini, Alfredo

1994-01-01

As the role of the modern engineer is markedly different from that of even a decade ago, the theme of engineering mathematics educa­ tion (EME) is an important one. The need for mathematical model­ ling (MM) courses and consideration of the educational impact of computer-based technology environments merit special attention. This book contains the proceeding of the NATO Advanced Research Workshop held on this theme in July 1993. We have left the industrial age behind and have entered the in­ formation age. Computers and other emerging technologies are penetrating society in depth and gaining a strong influence in de­ termining how in future society will be organised, while the rapid change of information requires a more qualified work force. This work force is vital to high technology and economic competitive­ ness in many industrialised countries throughout the world. Within this framework, the quality of EME has become an issue. It is expected that the content of mathematics courses taught in schools o...

Encyclopedia of well logging

International Nuclear Information System (INIS)

Desbrandes, R.

1985-01-01

The 16 chapters of this book aim to provide students, trainees and engineers with a manual covering all well-logging measurements ranging from drilling to productions, from oil to minerals going by way of geothermal energy. Each chapter is a summary but a bibliography is given at the end of each chapter. Well-logging during drilling, wireline logging equipment and techniques, petroleum logging, data processing of borehole data, interpretation of well-logging, sampling tools, completion and production logging, logging in relief wells to kill off uncontrolled blowouts, techniques for high temperature geothermal energy, small-scale mining and hydrology, logging with oil-base mud and finally recommended logging programs are all topics covered. There is one chapter on nuclear well-logging which is indexed separately. (UK)

The Third Injection Technique Workshop In Athens (TITAN)

NARCIS (Netherlands)

Frid, A.; Hirsch, L.; Gaspar, R.; Hicks, D.; Kreugel, G.; Liersch, J.; Letondeur, C.; Sauvanet, J. P.; Tubiana-Rufi, N.; Strauss, K.

The first Injection Technique workshop brought together endocrinologists and injection experts from around the world in Strasbourg in 1997. From its work came groundbreaking recommendations which advanced best practices in areas such as the use of a skin fold when injecting. The second Injection

Interpretation of horizontal well production logs: influence of logging tool

Energy Technology Data Exchange (ETDEWEB)

Ozkan, E. [Colorado School of Mines, Boulder, CO (United States); Sarica, C. [Pennsylvania State Univ., College Park, PA (United States); Haci, M. [Drilling Measurements, Inc (United States)

1998-12-31

The influence of a production-logging tool on wellbore flow rate and pressure measurements was investigated, focusing on the disturbence caused by the production-logging tool and the coiled tubing on the original flow conditions in the wellbore. The investigation was carried out using an analytical model and single-phase liquid flow was assumed. Results showed that the production-logging tool influenced the measurements as shown by the deviation of the original flow-rate, pressure profiles and low-conductivity wellbores. High production rates increase the effect of the production-logging tool. Recovering or inferring the original flow conditions in the wellbore from the production-logging data is a very complex process which cannot be solved easily. For this reason, the conditions under which the information obtained by production-logging is meaningful is of considerable practical interest. 7 refs., 2 tabs., 15 figs.

Forest Roadidentification and Extractionof Through Advanced Log Matching Techniques

Science.gov (United States)

Zhang, W.; Hu, B.; Quist, L.

2017-10-01

A novel algorithm for forest road identification and extraction was developed. The algorithm utilized Laplacian of Gaussian (LoG) filter and slope calculation on high resolution multispectral imagery and LiDAR data respectively to extract both primary road and secondary road segments in the forest area. The proposed method used road shape feature to extract the road segments, which have been further processed as objects with orientation preserved. The road network was generated after post processing with tensor voting. The proposed method was tested on Hearst forest, located in central Ontario, Canada. Based on visual examination against manually digitized roads, the majority of roads from the test area have been identified and extracted from the process.

FOREST ROADIDENTIFICATION AND EXTRACTIONOF THROUGH ADVANCED LOG MATCHING TECHNIQUES

Directory of Open Access Journals (Sweden)

W. Zhang

2017-10-01

Full Text Available A novel algorithm for forest road identification and extraction was developed. The algorithm utilized Laplacian of Gaussian (LoG filter and slope calculation on high resolution multispectral imagery and LiDAR data respectively to extract both primary road and secondary road segments in the forest area. The proposed method used road shape feature to extract the road segments, which have been further processed as objects with orientation preserved. The road network was generated after post processing with tensor voting. The proposed method was tested on Hearst forest, located in central Ontario, Canada. Based on visual examination against manually digitized roads, the majority of roads from the test area have been identified and extracted from the process.

Successful Sampling Strategy Advances Laboratory Studies of NMR Logging in Unconsolidated Aquifers

Science.gov (United States)

Behroozmand, Ahmad A.; Knight, Rosemary; Müller-Petke, Mike; Auken, Esben; Barfod, Adrian A. S.; Ferré, Ty P. A.; Vilhelmsen, Troels N.; Johnson, Carole D.; Christiansen, Anders V.

2017-11-01

The nuclear magnetic resonance (NMR) technique has become popular in groundwater studies because it responds directly to the presence and mobility of water in a porous medium. There is a need to conduct laboratory experiments to aid in the development of NMR hydraulic conductivity models, as is typically done in the petroleum industry. However, the challenge has been obtaining high-quality laboratory samples from unconsolidated aquifers. At a study site in Denmark, we employed sonic drilling, which minimizes the disturbance of the surrounding material, and extracted twelve 7.6 cm diameter samples for laboratory measurements. We present a detailed comparison of the acquired laboratory and logging NMR data. The agreement observed between the laboratory and logging data suggests that the methodologies proposed in this study provide good conditions for studying NMR measurements of unconsolidated near-surface aquifers. Finally, we show how laboratory sample size and condition impact the NMR measurements.

Transactions of the criticality alarm systems workshop

International Nuclear Information System (INIS)

1988-01-01

The first Criticality Alarm workshop was held by the US Department of Energy Albuquerque Operations Office in 1985. This second workshop is the first held on an international level. There were 98 persons in attendance. They represented the Department of Energy (DOE) field offices, DOE contractors, the Nuclear Regulatory Commission (NRC), NRC licensees, and agencies in the United Kingdom, France, West Germany, and Japan. Topics were on practices experience, and development. A key value of the workshop was the sharing of critical alarm system experiences, problems, and advances in the state of the art. In addition, several Criticality Alarm Systems (CAS) equipment systems were exhibited. Papers were presented on: nature of criticality accidents; lessons learned from past accidents; application of ANS 8.3 standard; gamma and neutron detection systems; research and development in progress; testing at Oak Ridge and Los Alamos; methods used to place detectors; centralized readout feature; false alarms; trip-point settings; and testing and maintenance. The individual papers have been cataloged separately

Imaging Sciences Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Candy, J.V.

1996-11-21

This report contains the proceedings of the Imaging Sciences Workshop sponsored by C.A.S.LS., the Center for Advanced Signal & Image Sciences. The Center, established primarily to provide a forum where researchers can freely exchange ideas on the signal and image sciences in a comfortable intellectual environment, has grown over the last two years with the opening of a Reference Library (located in Building 272). The Technical Program for the 1996 Workshop include a variety of efforts in the Imaging Sciences including applications in the Microwave Imaging, highlighted by the Micro-Impulse Radar (MIR) system invented at LLNL, as well as other applications in this area. Special sessions organized by various individuals in Speech, Acoustic Ocean Imaging, Radar Ocean Imaging, Ultrasonic Imaging, and Optical Imaging discuss various applica- tions of real world problems. For the more theoretical, sessions on Imaging Algorithms and Computed Tomography were organized as well as for the more pragmatic featuring a session on Imaging Systems.

Small genomes: New initiatives in mapping and sequencing. Workshop summary report

Energy Technology Data Exchange (ETDEWEB)

McKenney, K. [National Inst. of Standards and Technology, Gaithersburg, MD (United States). Biotechnology Div.; Robb, F. [Univ. of Maryland Biotechnology Inst., Baltimore, MD (United States). Center of Marine Biotechnology

1993-12-31

The workshop was held 5--7 July 1993 at the Center for Advanced Research in Biotechnology (CARB) and hosted by the University of Maryland Biotechnology Institute (UMBI) and the National Institute of Standards and Technology (NIST). The objective of this workshop was to bring together individuals interested in DNA technologies and to determine the impact of these current and potential improvements of the speed and cost-effectiveness of mapping and sequencing on the planning of future small genome projects. A major goal of the workshop was to spur the collaboration of more diverse groups of scientists working on this topic, and to minimize competitiveness as an inhibitory factor to progress.

Proceedings of the Workshop on Current and Emerging methods for Optimising Safety and Efficiency in Nuclear Decommissioning

International Nuclear Information System (INIS)

2017-02-01

The workshop was organised by the Institute for Energy Technology (IFE) on behalf of the OECD Halden Reactor Project (OECD-HRP) and in collaboration with the International Atomic Energy Agency (IAEA) and the Nuclear Energy Agency (NEA). The workshop brought together more than 100 people (operators, regulators, scientists, consultants, and contractors) from 25 countries. Program: Day 1 - Successful application of R and D in decommissioning and future needs (Welcome and Opening Speeches; Session 1: Workshop Introductory Presentations; Session 2: Experience from starting, on-going and completed decommissioning projects). Day 2 - R and D and application of advanced technologies for decommissioning (Session 3: New technologies for decommissioning; Session 4: Advanced information technologies for decommissioning). Day 3 - Improving decommissioning management on project, national and international level (Session 5: Challenges and methods for improving decommissioning; Session 6: Workshop closing)

Workshop on high heat load x-ray optics

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

A workshop on High Heat Load X-Ray Optics'' was held at Argonne National Laboratory on August 3--5, 1989. The object of this workshop was to discuss recent advances in the art of cooling x-ray optics subject to high heat loads from synchrotron beams. The cooling of the first optical element in the intense photon beams that will be produced in the next generation of synchrotron sources is recognized as one of the major challenges that must be faced before one will be able to use these very intense beams in future synchrotron experiments. Considerable advances have been made in this art during the last few years, but much work remains to be done before the heating problem can be said to be completely solved. Special emphasis was placed on recent cooling experiments and detailed finite element'' and finite difference'' calculations comparing experiment with theory and extending theory to optimize performance.

Imaging Sciences Workshop, Proceedings, November 15-16, 1995

Energy Technology Data Exchange (ETDEWEB)

Candy, J.V.

1995-11-01

Welcome to the Imaging Sciences Workshop sponsored by C.A.S.I.S., the Center for Advanced Signal & Image Sciences. Many programs at LLNL use advanced signal and image processing techniques, and the Center was established to encourage the exchange of ideas and to promote collaboration by individuals from these programs. This Workshop is an opportunity for LLNL personnel and invited speakers from other organizations not only to present new work, but, perhaps more importantly, to discuss problems in an informal and friendly setting. This year marks the opening of the CASIS Reference Library in Building 272, and we encourage all attendees to stop by for a look and to make use of it in the future. The Technical Program covers a wide variety of applications at LLNL including physical systems for collecting data and processing techniques for recovering and enhancing images. We hope that you enjoy the presentations, and we encourage you to participate in the discussions. Thanks for attending.

8th International Workshop on Non-Monotonic Reasoning

CERN Document Server

Truszczynski, Mirek

2000-01-01

The papers gathered in this collection were presented at the 8th International Workshop on Nonmonotonic Reasoning, NMR2000. The series was started by John McCarthy in 1978. The first international NMR workshop was held at Mohonk Mountain House, New Paltz, New York in June, 1984, and was organized by Ray Reiter and Bonnie Webber. In the last 10 years the area of nonmonotonic reasoning has seen a number of important developments. Significant theoretical advances were made in the understanding of general abstract principles underlying nonmonotonicity. Key results on the expressibility and computational complexity of nonmonotonic logics were established. The role of nonmonotonic reasoning in belief revision, abduction, reasoning about action, planing and uncertainty was further clarified. Several successful NMR systems were built and used in applications such as planning, scheduling, logic programming and constraint satisfaction. The papers in the proceedings reflect these recent advances in the field. They are g...

Workshop on high heat load x-ray optics

International Nuclear Information System (INIS)

1990-01-01

A workshop on ''High Heat Load X-Ray Optics'' was held at Argonne National Laboratory on August 3--5, 1989. The object of this workshop was to discuss recent advances in the art of cooling x-ray optics subject to high heat loads from synchrotron beams. The cooling of the first optical element in the intense photon beams that will be produced in the next generation of synchrotron sources is recognized as one of the major challenges that must be faced before one will be able to use these very intense beams in future synchrotron experiments. Considerable advances have been made in this art during the last few years, but much work remains to be done before the heating problem can be said to be completely solved. Special emphasis was placed on recent cooling experiments and detailed ''finite element'' and ''finite difference'' calculations comparing experiment with theory and extending theory to optimize performance

Effectiveness of a 1-day workshop on scientific writing conducted by the Indian journal of rheumatology

Directory of Open Access Journals (Sweden)

Mohit Goyal

2018-01-01

Full Text Available Background: Writing a scientific manuscript is an important skill to acquire for junior doctors considering the mandatory requirement of research publications during post-graduate training and for career advancement in India. Methods: We conducted a one-day workshop on scientific writing and publication at Udaipur in November 2017, comprising both didactic lectures as well as hands-on evaluation of a dummy manuscript, and evaluated structured questionnaires filled pre- and post-workshop. Results: There were 120 attendees, most of whom were junior doctors with little or no prior experience in writing a scientific paper. A significant baseline knowledge deficit regarding the principles and processes of scientific writing (ranging from 20.9% to 77.3% participants for the different questions asked could be identified before the workshop. This knowledge deficit was significantly improved in most areas as assessed after the workshop. We identified the need to discuss predatory publishing in greater detail in subsequent workshops, as 20.8% of respondents after the workshop professed that they might consider publishing in a predatory journal. As expressed in participant feedback, longer, more-specialized or advanced level workshops on scientific writing in the future could also consider including more details on appropriate statistical presentation and pictorial representation of data as well as longer time spent on hands-on exercises. Conclusion: There remains a need to conduct more scientific writing workshops by national societies and journals all over the country.

Analysis of RIA standard curve by log-logistic and cubic log-logit models

International Nuclear Information System (INIS)

Yamada, Hideo; Kuroda, Akira; Yatabe, Tami; Inaba, Taeko; Chiba, Kazuo

1981-01-01

In order to improve goodness-of-fit in RIA standard analysis, programs for computing log-logistic and cubic log-logit were written in BASIC using personal computer P-6060 (Olivetti). Iterative least square method of Taylor series was applied for non-linear estimation of logistic and log-logistic. Hear ''log-logistic'' represents Y = (a - d)/(1 + (log(X)/c)sup(b)) + d As weights either 1, 1/var(Y) or 1/σ 2 were used in logistic or log-logistic and either Y 2 (1 - Y) 2 , Y 2 (1 - Y) 2 /var(Y), or Y 2 (1 - Y) 2 /σ 2 were used in quadratic or cubic log-logit. The term var(Y) represents squares of pure error and σ 2 represents estimated variance calculated using a following equation log(σ 2 + 1) = log(A) + J log(y). As indicators for goodness-of-fit, MSL/S sub(e)sup(2), CMD% and WRV (see text) were used. Better regression was obtained in case of alpha-fetoprotein by log-logistic than by logistic. Cortisol standard curve was much better fitted with cubic log-logit than quadratic log-logit. Predicted precision of AFP standard curve was below 5% in log-logistic in stead of 8% in logistic analysis. Predicted precision obtained using cubic log-logit was about five times lower than that with quadratic log-logit. Importance of selecting good models in RIA data processing was stressed in conjunction with intrinsic precision of radioimmunoassay system indicated by predicted precision. (author)

Frontiers of interfacial water research :workshop report.

Energy Technology Data Exchange (ETDEWEB)

Cygan, Randall Timothy; Greathouse, Jeffery A.

2005-10-01

Water is the critical natural resource of the new century. Significant improvements in traditional water treatment processes require novel approaches based on a fundamental understanding of nanoscale and atomic interactions at interfaces between aqueous solution and materials. To better understand these critical issues and to promote an open dialog among leading international experts in water-related specialties, Sandia National Laboratories sponsored a workshop on April 24-26, 2005 in Santa Fe, New Mexico. The ''Frontiers of Interfacial Water Research Workshop'' provided attendees with a critical review of water technologies and emphasized the new advances in surface and interfacial microscopy, spectroscopy, diffraction, and computer simulation needed for the development of new materials for water treatment.

77 FR 31371 - Public Workshop: Privacy Compliance Workshop

Science.gov (United States)

2012-05-25

... presentations, including the privacy compliance fundamentals, privacy and data security, and the privacy... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary Public Workshop: Privacy Compliance... Homeland Security Privacy Office will host a public workshop, ``Privacy Compliance Workshop.'' DATES: The...

2005 NASA Seal/Secondary Air System Workshop, Volume 1

Science.gov (United States)

Steinetz, Bruce M. (Editor); Hendricks, Robert C. (Editor)

2006-01-01

The 2005 NASA Seal/Secondary Air System workshop covered the following topics: (i) Overview of NASA s new Exploration Initiative program aimed at exploring the Moon, Mars, and beyond; (ii) Overview of the NASA-sponsored Propulsion 21 Project; (iii) Overview of NASA Glenn s seal project aimed at developing advanced seals for NASA s turbomachinery, space, and reentry vehicle needs; (iv) Reviews of NASA prime contractor, vendor, and university advanced sealing concepts including tip clearance control, test results, experimental facilities, and numerical predictions; and (v) Reviews of material development programs relevant to advanced seals development. Turbine engine studies have shown that reducing high-pressure turbine (HPT) blade tip clearances will reduce fuel burn, lower emissions, retain exhaust gas temperature margin, and increase range. Several organizations presented development efforts aimed at developing faster clearance control systems and associated technology to meet future engine needs. The workshop also covered several programs NASA is funding to develop technologies for the Exploration Initiative and advanced reusable space vehicle technologies. NASA plans on developing an advanced docking and berthing system that would permit any vehicle to dock to any on-orbit station or vehicle. Seal technical challenges (including space environments, temperature variation, and seal-on-seal operation) as well as plans to develop the necessary "androgynous" seal technologies were reviewed. Researchers also reviewed tests completed for the shuttle main landing gear door seals.

Workshops som forskningsmetode

OpenAIRE

Ørngreen, Rikke; Levinsen, Karin Tweddell

2017-01-01

This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on the latter, this paper presents five studies on upper secondary and higher education teachers’ professional development and on teaching and learnin...

The 13th international workshop on targetry and target chemistry proceedings

Energy Technology Data Exchange (ETDEWEB)

Haroun, S. (SFU, TRIUMF (Canada)); Givskov, A.; Jensen, Mikael (Technical Univ. of Denmark. Risoe National Laboratory for Sustainable Energy, Radiation Research Division, Roskilde (Denmark))

2011-06-15

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

The 13th international workshop on targetry and target chemistry proceedings

International Nuclear Information System (INIS)

Haroun, S.; Givskov, A.; Jensen, Mikael

2011-06-01

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

Report on the Aseismic Slip, Tremor, and Earthquakes Workshop

Science.gov (United States)

Gomberg, Joan; Roeloffs, Evelyn; Trehu, Anne; Dragert, Herb; Meertens, Charles

2008-01-01

This report summarizes the discussions and information presented during the workshop on Aseismic Slip, Tremor, and Earthquakes. Workshop goals included improving coordination among those involved in conducting research related to these phenomena, assessing the implications for earthquake hazard assessment, and identifying ways to capitalize on the education and outreach opportunities presented by these phenomena. Research activities of focus included making, disseminating, and analyzing relevant measurements; the relationships among tremor, aseismic or 'slow-slip', and earthquakes; and discovering the underlying causative physical processes. More than 52 participants contributed to the workshop, held February 25-28, 2008 in Sidney, British Columbia. The workshop was sponsored by the U.S. Geological Survey, the National Science Foundation?s Earthscope Program and UNAVCO Consortium, and the Geological Survey of Canada. This report has five parts. In the first part, we integrate the information exchanged at the workshop as it relates to advancing our understanding of earthquake generation and hazard. In the second part, we summarize the ideas and concerns discussed in workshop working groups on Opportunities for Education and Outreach, Data and Instrumentation, User and Public Needs, and Research Coordination. The third part presents summaries of the oral presentations. The oral presentations are grouped as they were at the workshop in the categories of phenomenology, underlying physical processes, and implications for earthquake hazards. The fourth part contains the meeting program and the fifth part lists the workshop participants. References noted in parentheses refer to the authors of presentations made at the workshop, and published references are noted in square brackets and listed in the Reference section. Appendix A contains abstracts of all participant presentations and posters, which also have been posted online, along with presentations and author contact

Proceedings: Joint DOE/NSF Workshop on flow of particulates and fluids

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

These proceedings are the result of the Fifth DOR-NSF Workshop on fundamental research in the area of particulate two-phase flow and granular flow. The present collection of twenty contributions from universities and national laboratories is based on research projects sponsored by either the Department of Energy or the National Science Foundation. These papers illustrate some of the latest advances in theory, simulations, and experiments. The papers from the Workshop held September 29--October 1, 1993 have been separated into three basic areas: experiments, theory, and numerical simulations. A list of attendees at the workshop is included at the end of the proceedings. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Space Transportation Technology Workshop: Propulsion Research and Technology

Science.gov (United States)

2000-01-01

This viewgraph presentation gives an overview of the Space Transportation Technology Workshop topics, including Propulsion Research and Technology (PR&T) project level organization, FY 2001 - 2006 project roadmap, points of contact, foundation technologies, auxiliary propulsion technology, PR&T Low Cost Turbo Rocket, and PR&T advanced reusable technologies RBCC test bed.

GKSS-workshop: contaminated sludges. Treatment and utilization fine graned residues; GKSS-Workshop: Kontaminierte Schlaemme. Behandlung und Nutzungsmoeglichkeiten feinkoerniger Reststoffe

Energy Technology Data Exchange (ETDEWEB)

Alvermann, G.; Luther, G.; Niemeyer, B. [eds.] [GKSS-Forschungszentrum Geesthacht GmbH (Germany). Zentralabteilung Technikum

2000-07-01

New regulations, such as the materials recycling act, soil protection act and unsolved problems related to the treatment of contaminated sludges, the utilisation of the gained products demand the development of innovative techniques for industrial, dredged or drilling sludges. The workshop offered a platform for intensive discussions between representatives of industry, research institutions, associations, and authorities. The main aim of the workshop was the presentation of fundamental background of sludge processing and advanced technical solutions. The available proceedings contain 21 lectures held on the workshop with the following ranges of topics of the sludge treatment: legislation, R and D-funding, technological bases, decontamination processes, dewatering and drying processes, recycling and immobilization. (orig.) [German] Neue Gesetze wie das Kreislaufwirtschafts- oder das Bundes-Bodenschutzgesetz und anstehende Probleme bei der Beseitigung belasteter Schlaemme - zum Beispiel Industrie-, Bohr- und Baggergutschlaemme - erfordern die Entwicklung innovativer Techniken zu ihrer Aufbereitung, Reinigung bzw. Verwertung. Der Workshop bot ein Formung zur intensiven Diskussion zwischen Industrie, Forschung, Verbaenden und Behoerden. Ziel war es, unterschiedliche Methoden der Schlammbehandlung zu eroertern, Loesungswege aufzuzeigen und Moeglichkeiten fuer Kooperationen zu erarbeiten. Der vorliegende Band enthaelt Beitraege der Referenten, die sich auf folgende Themenbereiche der Schlammbehandlung konzentrieren: juristische Aspekte, Foerdermoeglichkeiten, Grundlagen, Aufbereitung von Schlaemmen, Entwaesserung und Trocknung von Schlaemmen, Verwertung und Immobilisierung. (orig.)

Dynamic Processes in Biology, Chemistry, and Materials Science: Opportunities for UltraFast Transmission Electron Microscopy - Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

Kabius, Bernd C.; Browning, Nigel D.; Thevuthasan, Suntharampillai; Diehl, Barbara L.; Stach, Eric A.

2012-07-25

This report summarizes a 2011 workshop that addressed the potential role of rapid, time-resolved electron microscopy measurements in accelerating the solution of important scientific and technical problems. A series of U.S. Department of Energy (DOE) and National Academy of Science workshops have highlighted the critical role advanced research tools play in addressing scientific challenges relevant to biology, sustainable energy, and technologies that will fuel economic development without degrading our environment. Among the specific capability needs for advancing science and technology are tools that extract more detailed information in realistic environments (in situ or operando) at extreme conditions (pressure and temperature) and as a function of time (dynamic and time-dependent). One of the DOE workshops, Future Science Needs and Opportunities for Electron Scattering: Next Generation Instrumentation and Beyond, specifically addressed the importance of electron-based characterization methods for a wide range of energy-relevant Grand Scientific Challenges. Boosted by the electron optical advancement in the last decade, a diversity of in situ capabilities already is available in many laboratories. The obvious remaining major capability gap in electron microscopy is in the ability to make these direct in situ observations over a broad spectrum of fast (µs) to ultrafast (picosecond [ps] and faster) temporal regimes. In an effort to address current capability gaps, EMSL, the Environmental Molecular Sciences Laboratory, organized an Ultrafast Electron Microscopy Workshop, held June 14-15, 2011, with the primary goal to identify the scientific needs that could be met by creating a facility capable of a strongly improved time resolution with integrated in situ capabilities. The workshop brought together more than 40 leading scientists involved in applying and/or advancing electron microscopy to address important scientific problems of relevance to DOE’s research

Generalized localization for the double trigonometric Fourier series and the Walsh-Fourier series of functions in L log +L log + log +L

International Nuclear Information System (INIS)

Bloshanskaya, S K; Bloshanskii, I L; Roslova, T Y

1998-01-01

For an arbitrary open set Ω subset of I 2 =[0,1) 2 and an arbitrary function f element of L log + L log + log + L(I 2 ) such that f=0 on Ω the double Fourier series of f with respect to the trigonometric system Ψ=E and the Walsh-Paley system Ψ=W is shown to converge to zero (over rectangles) almost everywhere on Ω. Thus, it is proved that generalized localization almost everywhere holds on arbitrary open subsets of the square I 2 for the double trigonometric Fourier series and the Walsh-Fourier series of functions in the class L log + L log + log + L (in the case of summation over rectangles). It is also established that such localization breaks down on arbitrary sets that are not dense in I 2 , in the classes Φ Ψ (L)(I 2 ) for the orthonormal system Ψ=E and an arbitrary function such that Φ E (u)=o(u log + log + u) as u→∞ or for Φ W (u)=u( log + log + u) 1-ε , 0<ε<1

Advances in business ICT

CERN Document Server

Pełech-Pilichowski, Tomasz

2014-01-01

Futurists and scientists alike profess the coming of a new era in the history – the knowledge era. The notion of knowledge is as old as humans’ self-consciousness, but new challenges appear. The meaning of the word “knowledge” is changing from cognitive notion to a technical term denoting a structured economic resource to be actively managed. This contributed volume is a result of vivid and extremely valuable discussions held at 3rd International Workshop on Advances in Business ICT (ABICT) in Wrocław, Poland, September 9-12, 2012. The workshop focused on Advances in Business ICT approached from a multidisciplinary perspective. It provided an international forum for scientists/experts from academia and industry to discuss and exchange current results, applications, new ideas of ongoing research and experience on all aspects of Business Intelligence. ABICT has also been an opportunity to demonstrate different ideas and tools for developing and supporting organizational creativity, as well as advances ...

The midwest workshop on preparing nuclear engineering professionals

International Nuclear Information System (INIS)

Danofsky, R.A.; Rohach, A.F.; Spinrad, B.I.; Nodean, W.C.

1988-01-01

Personnel training and education are activities of major importance for nuclear utilities and represent fruitful areas for possible cooperation between utilities and educational institutions. Utility personnel have a need for continuing education through advanced and undergraduate degree programs and special courses. Nuclear engineering departments are in a position to meet at least some of these needs. The purpose of the workshop described in this paper was to explore ways to increase the dialogue between utilities and universities and to bring faculty and utility personnel together to discuss the educational needs of nuclear utilities. The workshop was held May 25-27, 1988, at Iowa State University. Planning for the workshop was coordinated by a steering committee with representation from the Department of Nuclear Engineering at Iowa State University, Iowa Electric Light and Power Company (IEL ampersand P), and Kirkwood Community College at Cedar Rapids, Iowa. Participants represented nuclear utilities, nuclear engineering departments, 2- and 4-yr colleges, a nuclear training organization, and the Institute of Nuclear Power Operations

Aerial Observation Needs Workshop, May 13-14, 2015

Energy Technology Data Exchange (ETDEWEB)

Nasiri, Shaima [Brookhaven National Lab. (BNL), Upton, NY (United States); Serbin, Shawn [Brookhaven National Lab. (BNL), Upton, NY (United States); Lesmes, David [Brookhaven National Lab. (BNL), Upton, NY (United States); Petty, Rick [Brookhaven National Lab. (BNL), Upton, NY (United States); Schmid, Beat [Brookhaven National Lab. (BNL), Upton, NY (United States); Vogelmann, Andrew [Brookhaven National Lab. (BNL), Upton, NY (United States); de Boer, Gijs [Brookhaven National Lab. (BNL), Upton, NY (United States); Dafflon, Baptiste [Brookhaven National Lab. (BNL), Upton, NY (United States); Guenther, Alex [Brookhaven National Lab. (BNL), Upton, NY (United States); Moore, David [Brookhaven National Lab. (BNL), Upton, NY (United States)

2015-10-01

The mission of the Climate and Environmental Sciences Division (CESD) of the Office of Biological and Environmental Research (BER) within the U.S. Department of Energy's (DOE) Office of Science is "to advance a robust, predictive understanding of Earth's climate and environmental systems and to inform the development of sustainable solutions to the nation's energy and environmental challenges." Accomplishing this mission requires aerial observations of the atmospheric and terrestrial components of the climate system. CESD is assessing its current and future aerial observation needs to develop a strategy and roadmap of capability requirements for the next decade. To facilitate this process, a workshop was convened that consisted of invited experts in the atmospheric and terrestrial sciences, airborne observations, and modeling. This workshop report summarizes the community input prior to and during the workshop on research challenges and opportunities, as well as specific science questions and observational needs that require aerial observations to address.

32th Winter Workshop on Nuclear Dynamics

CERN Document Server

2016-01-01

The 32nd edition of the Winter Workshop will be held 28 February - 5 March 2016, Hotel Resort Fort Royal Guadeloupe in Guadeloupe a French overseas territory, is an island group in the southern Caribbean Sea. As with previous years, the workshop will bring together scientists from all fields of nuclear physics for engaging and friendly exchanges of ideas. Much emphasis will be on the recent LHC, RHIC and SPS heavy ion results, but advances in the ongoing and future programs at FAIR, FRIB, EIC, JLab and NICA and will also be featured. The meeting will start with a welcome reception on the evening of Sunday, February 28. The workshop program will commence on Monday morning and run until Saturday. We recommend to arrive on Sunday and leave on Sunday. Talks will be as usual 25+5 minutes, there will be no parallel sessions. If you are interested in presenting your work, please fill out the registration form prior to the registration deadline. After the program committee has met we will confirm your talk via indivi...

30th Winter Workshop on Nuclear Dynamics

CERN Document Server

2014-01-01

The 30th edition of the Winter Workshop will be held April 6-12th, 2014 in Hotel Galvez & Spa, Galveston, Texas, USA. As with previous years, the workshop will bring together scientists from all fields of nuclear physics for engaging and friendly exchanges of ideas.Much emphasis will be on the recent LHC and RHIC heavy ion results, but advances in the ongoing and future programs at FAIR, FRIB, NICA and JLab will also be featured. The meeting will start with a welcome reception on the evening of Sunday, April 6th. The workshop program will commence on Monday morning and run until Saturday evening. We recommend to arrive on Sunday and leave on Sunday. Talks will be as usual 25+5 minutes, there will be no parallel sessions. If you are interested in presenting your work, please fill out the registration form prior to the registration deadline. After the program committee has met we will confirm your talk via individual invitations. We will also work with the talks committees of all relevant experimenta...

Borehole logging

International Nuclear Information System (INIS)

Olsen, H.

1995-01-01

Numerous ground water investigations have been accomplished by means of borehole logging. Borehole logging can be applied to establish new water recovery wells, to control the existing water producing wells and source areas and to estimate ground water quality. (EG)

Providing a computing environment for a high energy physics workshop

International Nuclear Information System (INIS)

Nicholls, J.

1991-03-01

Although computing facilities have been provided at conferences and workshops remote from the hose institution for some years, the equipment provided has rarely been capable of providing for much more than simple editing and electronic mail over leased lines. This presentation describes the pioneering effort involved by the Computing Department/Division at Fermilab in providing a local computing facility with world-wide networking capability for the Physics at Fermilab in the 1990's workshop held in Breckenridge, Colorado, in August 1989, as well as the enhanced facilities provided for the 1990 Summer Study on High Energy Physics at Snowmass, Colorado, in June/July 1990. Issues discussed include type and sizing of the facilities, advance preparations, shipping, on-site support, as well as an evaluation of the value of the facility to the workshop participants

High pressure and synchrotron radiation satellite workshop

Energy Technology Data Exchange (ETDEWEB)

Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A

2006-07-01

The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations.

36th Brazilian Workshop on Nuclear Physics

CERN Document Server

Brandão de Oliveira, José Roberto; Barbosa Shorto, Julian Marco; Higa, Renato

2014-01-01

The Brazilian Workshop on Nuclear Physics (RTFNB, acronym in Portuguese) is organized annually by the Brazilian Physics Society since 1978, in order to: promote Nuclear Physics research in the country; stimulate and reinforce collaborations among nuclear physicists from around the country; disseminate advances in nuclear physics research and its applications; disseminate, disclose and evaluate the scientific production in this field.

High pressure and synchrotron radiation satellite workshop

International Nuclear Information System (INIS)

Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A.

2006-01-01

The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations

Summary report of IAEA workshop on atomic and molecular data for fusion energy research

International Nuclear Information System (INIS)

Clark, R.E.H.

2007-02-01

A workshop on Atomic and Molecular (A+M) Data for Fusion Energy Research was held at the International Centre for Theoretical Physics (ICTP) in Trieste, Italy, from 28 August until 8 September 2006. The workshop was attended by fourteen students and three ICTP associates representing eleven Member States. A total of eight lecturers, including six external to the Agency, made presentations to the workshop. All lecturers provided advance copies of the lecture materials, and provided written assignments for the students to provide practical examples of applications of data issues to actual problems related to fusion energy research. All materials were collected on CDs, which were distributed to the students at the conclusion of the workshop. During the course of the workshop, the students were given the opportunity to describe their background and research interests. The workshop did arouse interest in A+M processes related to fusion, and was viewed as successful by both the students and lecturers. (author)

Logging Concessions Enable Illegal Logging Crisis in the Peruvian Amazon

Science.gov (United States)

Finer, Matt; Jenkins, Clinton N.; Sky, Melissa A. Blue; Pine, Justin

2014-04-01

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US-Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3% of all concessions supervised by authorities were suspected of major violations. Of the 609 total concessions, nearly 30% have been cancelled for violations and we expect this percentage to increase as investigations continue. Moreover, the nature of the violations indicate that the permits associated with legal concessions are used to harvest trees in unauthorized areas, thus threatening all forested areas. Many of the violations pertain to the illegal extraction of CITES-listed timber species outside authorized areas. These findings highlight the need for additional reforms.

Logging concessions enable illegal logging crisis in the Peruvian Amazon.

Science.gov (United States)

Finer, Matt; Jenkins, Clinton N; Sky, Melissa A Blue; Pine, Justin

2014-04-17

The Peruvian Amazon is an important arena in global efforts to promote sustainable logging in the tropics. Despite recent efforts to achieve sustainability, such as provisions in the US-Peru Trade Promotion Agreement, illegal logging continues to plague the region. We present evidence that Peru's legal logging concession system is enabling the widespread illegal logging via the regulatory documents designed to ensure sustainable logging. Analyzing official government data, we found that 68.3% of all concessions supervised by authorities were suspected of major violations. Of the 609 total concessions, nearly 30% have been cancelled for violations and we expect this percentage to increase as investigations continue. Moreover, the nature of the violations indicate that the permits associated with legal concessions are used to harvest trees in unauthorized areas, thus threatening all forested areas. Many of the violations pertain to the illegal extraction of CITES-listed timber species outside authorized areas. These findings highlight the need for additional reforms.

Standard Modular Hydropower Technology Acceleration Workshop: Summary Report

Energy Technology Data Exchange (ETDEWEB)

Smith, Brennan T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); DeNeale, Scott T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Witt, Adam M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mobley, Miles H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Fernandez, Alisha R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

In support of the Department of Energy (DOE) funded Standard Modular Hydropower (SMH) Technology Acceleration project, Oak Ridge National Laboratory (ORNL) staff convened with five small hydropower technology entrepreneurs on June 14 and 15, 2017 to discuss gaps, challenges, and opportunities for small modular hydropower development. The workshop was designed to walk through SMH concepts, discuss the SMH research vision, assess how each participant’s technology aligns with SMH concepts and research, and identify future pathways for mutually beneficial collaboration that leverages ORNL expertise and entrepreneurial industry experience. The goal coming out of the workshop is to advance standardized, scalable, modular hydropower technologies and development approaches with sustained and open dialogue among diverse stakeholder groups.

Fluid-Rock Characterization and Interactions in NMR Well Logging

Energy Technology Data Exchange (ETDEWEB)

George J. Hirasaki; Kishore K. Mohanty

2005-09-05

The objective of this report is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity. Oil based drilling fluids can have an adverse effect on NMR well logging if it alters the wettability of the formation. The effect of various surfactants on wettability and surface relaxivity are evaluated for silica sand. The relation between the relaxation time and diffusivity distinguishes the response of brine, oil, and gas in a NMR well log. A new NMR pulse sequence in the presence of a field gradient and a new inversion technique enables the T{sub 2} and diffusivity distributions to be displayed as a two-dimensional map. The objectives of pore morphology and rock characterization are to identify vug connectivity by using X-ray CT scan, and to improve NMR permeability correlation. Improved estimation of permeability from NMR response is possible by using estimated tortuosity as a parameter to interpolate between two existing permeability models.

Diabetic foot workshop: Improving technical and educational skills for nurses.

Science.gov (United States)

Aalaa, Maryam; Sanjari, Mahnaz; Shahbazi, Samimeh; Shayeganmehr, Zahra; Abooeirad, Maryam; Amini, Mohammad Reza; Adibi, Hossien; Mehrdad, Neda

2017-01-01

Diabetes mellitus as one of the most common metabolic disorders has some complications, one of the main ones is diabetic foot (DF). Appropriate care and education prevents 85% of diabetic foot amputations. An ideal management to prevent and treat diabetic foot necessitates a close collaboration between the health team members and the diabetic patient. Therefore, improving nurses' knowledge about DF care and advancement in the quality of care provided by the nurses could significantly improve diabetic foot prevention and management. Therefore, the aim of DF workshop was to improve technical and educational skills of the nurses to prevent and manage diabetic foot. Considering the vital role of the nurses in providing DF care, EMRI decided to conduct Diabetic foot workshop for them. The following five steps were designed for the 14 coordinating sessions in the workshop: Goals definition, deciding about attendees, location selection, creating agenda, and developing a follow-up plan. "Diabetic Foot Workshop for Nurses" provides appropriate training to DF nurses at the national level; and combining theory and practice in this workshop not only increases nurses' knowledge, but also improves their skills in the field of the diabetic foot. Providing education and care to patients by DF nurse specialists instead of general nurses could be an important output of this workshop, which may lead to DF prevention and amputation decrease in the long term.

PREFACE: Collapse Calderas Workshop

Science.gov (United States)

Gottsmann, Jo; Aguirre-Diaz, Gerardo

2008-10-01

Caldera-formation is one of the most awe-inspiring and powerful displays of nature's force. Resultant deposits may cover vast areas and significantly alter the immediate topography. Post-collapse activity may include resurgence, unrest, intra-caldera volcanism and potentially the start of a new magmatic cycle, perhaps eventually leading to renewed collapse. Since volcanoes and their eruptions are the surface manifestation of magmatic processes, calderas provide key insights into the generation and evolution of large-volume silicic magma bodies in the Earth's crust. Despite their potentially ferocious nature, calderas play a crucial role in modern society's life. Collapse calderas host essential economic deposits and supply power for many via the exploitation of geothermal reservoirs, and thus receive considerable scientific, economic and industrial attention. Calderas also attract millions of visitors world-wide with their spectacular scenic displays. To build on the outcomes of the 2005 calderas workshop in Tenerife (Spain) and to assess the most recent advances on caldera research, a follow-up meeting was proposed to be held in Mexico in 2008. This abstract volume presents contributions to the 2nd Calderas Workshop held at Hotel Misión La Muralla, Querétaro, Mexico, 19-25 October 2008. The title of the workshop `Reconstructing the evolution of collapse calderas: Magma storage, mobilisation and eruption' set the theme for five days of presentations and discussions, both at the venue as well as during visits to the surrounding calderas of Amealco, Amazcala and Huichapan. The multi-disciplinary workshop was attended by more than 40 scientist from North, Central and South America, Europe, Australia and Asia. Contributions covered five thematic topics: geology, geochemistry/petrology, structural analysis/modelling, geophysics, and hazards. The workshop was generously supported by the International Association of Volcanology and the Chemistry of The Earth's Interior

Report on the value engineering workshop on APS beamline front ends

International Nuclear Information System (INIS)

Kuzay, T.

1993-01-01

A formal value engineering evaluation process was developed to address the front end components of the beamlines for the Advanced Photon Source (APS). This process (described in Section 2) involved an information phase, a creative phase, a judgment phase, a development phase, and a recommendation phase. Technical experts from other national laboratories and industry were invited to a two-day Value Engineering Workshop on November 5-6, 1992. The results of this Workshop are described in Section 4. Following the Workshop, various actions by the APS staff led to the redesign of the front end components, which are presented in Sections 5 and 6. The cost benefit analysis is presented in Section 7. It is important of realize that an added benefit of the Workshop was to obtain numerous design evaluations and enhancements of the front end components by experts in the field. As the design work proceeds to Title II completion, the APS staff is including many of these suggestions

Report of workshop on energy

International Nuclear Information System (INIS)

Tsujimoto, Kazufumi; Nagai, Yasuki

2005-03-01

The Working Group on Energy (WG) was organized under International Union of Pure and Applied Physics (IUPAP). The WG has been considering problems on future energy supply and role of physics to solve the subjects. As one of activities of the WG, a Workshop on Energy was held on May 13, 2004 at Center for Promotion of Computational Science and Engineering, Japan Atomic Energy Research Institute (JAERI) in Tokyo hosted by IUPAP and co-hosted by JAERI and High Energy Accelerator Research Organization. The objectives of this workshop are to suggest active contributions of pure and applied physics field to the solution of the energy problem and to advance research and development (R and D) of future energy through the discussions about present status, problem and prospect of different energy development in the world and in Japan. This report records the summary of the Workshop and, abstracts and materials of 12 presentations. After the invited presentations about overview of energy problems in the world, in China and in Japan, R and D activities on the following four fields were presented; 'Research and Development of New Energy', 'Research and Development of Fusion', 'Prospect of Accelerator Driven System (ADS)', and 'Hydrogen Production, Storage and Transportation'. At the end of the workshop, possible role of physics for the current and future energy problem was discussed. It was recognized that the energy problem was not as simple as to be solved by one country, and hence the international collaboration became essential. The importance of the coordination with other fields, such as chemistry and material, was also emphasized. (author)

15th Workshop on Crystalline Silicon Solar Cells and Modules: Materials and Processes; Extended Abstracts and Papers

Energy Technology Data Exchange (ETDEWEB)

Sopori, B. L.

2005-11-01

The National Center for Photovoltaics sponsored the 15th Workshop on Crystalline Silicon Solar Cells & Modules: Materials and Processes, held in Vail, CO, August 7-10, 2005. This meeting provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. The workshop addressed the fundamental properties of PV silicon, new solar cell designs, and advanced solar cell processing techniques. A combination of oral presentations by invited speakers, poster sessions, and discussion sessions reviewed recent advances in crystal growth, new cell designs, new processes and process characterization techniques, and cell fabrication approaches suitable for future manufacturing demands. The theme of this year's meeting was 'Providing the Scientific Basis for Industrial Success.' Specific sessions during the workshop included: Advances in crystal growth and material issues; Impurities and defects in Si; Advanced processing; High-efficiency Si solar cells; Thin Si solar cells; and Cell design for efficiency and reliability module operation. The topic for the Rump Session was ''Si Feedstock: The Show Stopper'' and featured a panel discussion by representatives from various PV companies.

Proceedings of the flexible, midsize gas turbine program planning workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The US Department of Energy (DOE) and the California Energy Commission (CEC) held a program planning workshop on March 4--5, 1997 in Sacramento, California on the subject of a flexible, midsize gas turbine (FMGT). The workshop was also co-sponsored by the Electric Power Research Institute (EPRI), the Gas Research Institute (GRI), the Gas Turbine Association (GTA), and the Collaborative Advanced Gas Turbine Program (CAGT). The purpose of the workshop was to bring together a broad cross section of knowledgeable people to discuss the potential benefits, markets, technical attributes, development costs, and development funding approaches associated with making this new technology available in the commercial marketplace. The participants in the workshop included representatives from the sponsoring organizations, electric utilities, gas utilities, independent power producers, gas turbine manufacturers, gas turbine packagers, and consultants knowledgeable in the power generation field. Thirteen presentations were given on the technical and commercial aspects of the subject, followed by informal breakout sessions that dealt with sets of questions on markets, technology requirements, funding sources and cost sharing, and links to other programs.

On the Cutting Edge Professional Development Program: Workshop and Web Resources for Current and Future Geoscience Faculty

Science.gov (United States)

MacDonald, R.; Manduca, C. A.; Mogk, D. W.; Tewksbury, B. J.

2004-12-01

Recognizing that many college and university faculty receive little formal training in teaching, are largely unaware of advances in research on teaching and learning, and face a variety of challenges in advancing in academic careers, the National Science Foundation-funded program On the Cutting Edge provides professional development for current and future faculty in the geosciences at various stages in their careers. The program includes a series of six multi-day workshops, sessions and one-day workshops at professional meetings, and a website with information about workshop opportunities and a variety of resources that bring workshop content to faculty (http://serc.carleton.edu/NAGTWorkshops). The program helps faculty improve their teaching and their job satisfaction by providing resources on instructional methods, geoscience content, and strategies for career planning. Workshop and website resources address innovative and effective practices in teaching, course design, delivery of instructional materials, and career planning, as well as approaches for teaching particular topics and strategies for starting and maintaining a research program in various institutional settings. Each year, special workshops for graduate students and post-doctoral fellows interested in academic careers and for early career faculty complement offerings on course design and emerging topics that are open to the full geoscience community. These special workshops include sessions on topics such as dual careers, gender issues, family-work balance, interviewing and negotiating strategies. The workshops serve as opportunities for networking and community building, with participants building connections with other participants as well as workshop leaders. Workshop participants reflect the full range of institutional diversity as well as ethnic and racial diversity beyond that of the geoscience faculty workforce. More than 40 percent of the faculty participants are female. Of the faculty

77 FR 43827 - International Workshop on Alternative Methods for Leptospira

Science.gov (United States)

2012-07-26

... recent advances and innovations in science and technology that can be applied to Leptospira vaccine... alternative methods. The workshop is open to the public at no charge with attendance limited only by the... priority. Leptospirosis affects numerous animal species including livestock, pets, and wildlife. Vaccines...

Natural language processing: state of the art and prospects for significant progress, a workshop sponsored by the National Library of Medicine.

Science.gov (United States)

Friedman, Carol; Rindflesch, Thomas C; Corn, Milton

2013-10-01

Natural language processing (NLP) is crucial for advancing healthcare because it is needed to transform relevant information locked in text into structured data that can be used by computer processes aimed at improving patient care and advancing medicine. In light of the importance of NLP to health, the National Library of Medicine (NLM) recently sponsored a workshop to review the state of the art in NLP focusing on text in English, both in biomedicine and in the general language domain. Specific goals of the NLM-sponsored workshop were to identify the current state of the art, grand challenges and specific roadblocks, and to identify effective use and best practices. This paper reports on the main outcomes of the workshop, including an overview of the state of the art, strategies for advancing the field, and obstacles that need to be addressed, resulting in recommendations for a research agenda intended to advance the field. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Proceedings of the 1987 coatings for advanced heat engines workshop

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

This Workshop was conducted to enhance communication among those involved in coating development for improved heat engine performance and durability. We were fortunate to have Bill Goward review the steady progress and problems encountered along the way in the use of thermal barrier coatings (TBC) in aircraft gas turbine engines. Navy contractors discussed their work toward the elusive goal of qualifying TBC for turbine airfoil applications. In the diesel community, Caterpillar and Cummins are developing TBC for combustion chamber components as part of the low heat rejection diesel engine concept. The diesel engine TBC work is based on gas turbine technology with a goal of more than twice the thickness used on gas turbine engine components. Adoption of TBC in production for diesel engines could justify a new generation of plasma spray coating equipment. Increasing interests in tribology were evident in this Workshop. Coatings have a significant role in reducing friction and wear under greater mechanical loadings at higher temperatures. The emergence of a high temperature synthetic lubricant could have an enormous impact on diesel engine design and operating conditions. The proven coating processes such as plasma spray, electron-beam physical vapor deposition, sputtering, and chemical vapor deposition have shown enhanced capabilities, particularly with microprocessor controls. Also, the newer coating schemes such as ion implantation and cathodic arc are demonstrating intriguing potential for engine applications. Coatings will play an expanding role in higher efficiency, more durable heat engines.

Advancing LGBTQI2 rights in developing countries through research ...

International Development Research Centre (IDRC) Digital Library (Canada)

2018-05-10

May 10, 2018 ... Advancing LGBTQI2 rights in developing countries through research ... the role of research in advancing the rights of lesbian, gay, bisexual, transgender, ... cities were discussed at ADAPTO's second international workshop.

System Software and Tools for High Performance Computing Environments: A report on the findings of the Pasadena Workshop, April 14--16, 1992

Energy Technology Data Exchange (ETDEWEB)

Sterling, T. [Universities Space Research Association, Washington, DC (United States); Messina, P. [Jet Propulsion Lab., Pasadena, CA (United States); Chen, M. [Yale Univ., New Haven, CT (United States)] [and others

1993-04-01

The Pasadena Workshop on System Software and Tools for High Performance Computing Environments was held at the Jet Propulsion Laboratory from April 14 through April 16, 1992. The workshop was sponsored by a number of Federal agencies committed to the advancement of high performance computing (HPC) both as a means to advance their respective missions and as a national resource to enhance American productivity and competitiveness. Over a hundred experts in related fields from industry, academia, and government were invited to participate in this effort to assess the current status of software technology in support of HPC systems. The overall objectives of the workshop were to understand the requirements and current limitations of HPC software technology and to contribute to a basis for establishing new directions in research and development for software technology in HPC environments. This report includes reports written by the participants of the workshop`s seven working groups. Materials presented at the workshop are reproduced in appendices. Additional chapters summarize the findings and analyze their implications for future directions in HPC software technology development.

5th International Workshop on Desorption Induced by Electronic Transitions

CERN Document Server

Jennison, Dwight R; Stechel, Ellen B; DIET V; Desorption induced by electronic transitions

1993-01-01

This volume in the Springer Series on Surface Sciences presents a recent account of advances in the ever-broadening field of electron-and photon-stimulated sur­ face processes. As in previous volumes, these advances are presented as the proceedings of the International Workshop on Desorption Induced by Electronic Transitions; the fifth workshop (DIET V) was held in Taos, New Mexico, April 1-4, 1992. It will be abundantly clear to the reader that "DIET" is not restricted to desorption, but has for several years included photochemistry, non-thermal surface modification, exciton self-trapping, and many other phenomena that are induced by electron or photon bombardment. However, most stimulated surface processes do share a common physics: initial electronic excitation, localization of the excitation, and conversion of electronic energy into nuclear kinetic energy. It is the rich variation of this theme which makes the field so interesting and fruitful. We have divided the book into eleven parts in orde...

CFD for Nuclear Reactor Safety Applications (CFD4NRS-4) - Workshop Proceedings

International Nuclear Information System (INIS)

2014-01-01

Following the CFD4NRS workshops held in Garching, Germany (Sept. 2006), Grenoble, France (Sep. 2008) and Washington D.C., USA (Sept. 2010), this Workshop is intended to extend the forum created for numerical analysts and experimentalists to exchange information in the application of CFD and CMFD to NRS issues and in guiding nuclear reactor design thinking. The workshop includes single-phase and multi-phase CFD applications, and offers the opportunity to present new experimental data for CFD validation. More emphasis has been given to the experiments, especially on two-phase flow, for advanced CMFD modelling for which sophisticated measurement techniques are required. Understanding of the physics has been depen before starting numerical analysis. Single-phase and multi-phase CFD simulations with a focus on validation were performed in areas such as: single-phase heat transfer, boiling flows, free-surface flows, direct contact condensation and turbulent mixing. These relate to NRS-relevant issues, such as pressurised thermal shock, critical heat flux, pool heat exchangers, boron dilution, hydrogen distribution in containments, thermal striping, etc. The use of systematic error quantification and the application of BPGs were strongly encouraged. Experiments providing data suitable for CFD or CMFD validation were also presented. These included local measurements using multi-sensor probes, laser-based techniques (LDV, PIV or LIF), hot-film/wire anemometry, imaging, or other advanced measuring techniques. There were over 150 registered participants at the CFD4NRS-4 workshop. The programme consisted of 48 technical papers. Of these, 44 were presented orally and 4 as posters. An additional 8 posters related to the OECD/NEA-KAERI sponsored CFD benchmark exercise on turbulent mixing in a rod bundle with spacers (MATiS-H) were presented and a special session was allocated for 6 video presentations. In addition, five keynote lectures were given by distinguished experts. The

Developing workshop module of realistic mathematics education: Follow-up workshop

Science.gov (United States)

Palupi, E. L. W.; Khabibah, S.

2018-01-01

Realistic Mathematics Education (RME) is a learning approach which fits the aim of the curriculum. The success of RME in teaching mathematics concepts, triggering students’ interest in mathematics and teaching high order thinking skills to the students will make teachers start to learn RME. Hence, RME workshop is often offered and done. This study applied development model proposed by Plomp. Based on the study by RME team, there are three kinds of RME workshop: start-up workshop, follow-up workshop, and quality boost. However, there is no standardized or validated module which is used in that workshops. This study aims to develop a module of RME follow-up workshop which is valid and can be used. Plopm’s developmental model includes materials analysis, design, realization, implementation, and evaluation. Based on the validation, the developed module is valid. While field test shows that the module can be used effectively.

Fourth Integrated Communications, Navigation, and Surveillance (ICNS) Conference and Workshop 2004: Conclusions and Recommendations

Science.gov (United States)

Phillips, Brent; Swanda, Ronald L.; Lewis, Michael S.; Kenagy, Randy; Donahue, George; Homans, Al; Kerczewski, Robert; Pozesky, Marty

2004-01-01

The NASA Glenn Research Center organized and hosted the Fourth Integrated Communications, Navigation, and Surveillance (ICNS) Technologies Conference and Workshop, which took place April 26-30, 2004 at the Hyatt Fair Lakes Hotel in Fairfax, Virginia. This fourth conference of the annual series followed the very successful first ICNS Conference (May 1-3, 2001 in Cleveland, Ohio), second ICNS conference (April 29-May 2, 2002 in Vienna, Virginia), and third ICNS conference (May 19-22, 2003 in Annapolis, Maryland). The purpose of the Fourth ICNS Conference was to assemble government, industry and academic communities performing research and development for advanced digital communications, surveillance and navigation systems and associated applications supporting the national and global air transportation systems to: 1) Understand current efforts and recent results in near- and far-term R&D and technology demonstration; 2) Identify integrated digital communications, navigation and surveillance R&D requirements necessary for a safe, secure and reliable, high-capacity, advanced air transportation system; 3) Provide a forum for fostering collaboration and coordination; and 4) Discuss critical issues and develop recommendations to achieve the future integrated CNS vision for national and global air transportation. The workshop attracted 316 attendees from government, industry and academia to address these purposes through technical presentations, breakout sessions, and individual and group discussions during the workshop and after-hours events, and included 16 international attendees. An Executive Committee consisting of representatives of several key segments of the aviation community concerned with CNS issues met on the day following the workshop to consider the primary outcomes and recommendations of the workshop. This report presents an overview of the conference, workshop breakout session results, and the findings of the Executive Committee.

A workshop series using peer-grading to build drug information, writing, critical-thinking, and constructive feedback skills.

Science.gov (United States)

Davis, Lindsay E

2014-12-15

To utilize a skills-based workshop series to develop pharmacy students' drug information, writing, critical-thinking, and evaluation skills during the final didactic year of training. A workshop series was implemented to focus on written (researched) responses to drug information questions. These workshops used blinded peer-grading to facilitate timely feedback and strengthen assessment skills. Each workshop was aligned to the didactic coursework content to complement and extend learning, while bridging and advancing research, writing, and critical thinking skills. Attainment of knowledge and skills was assessed by rubric-facilitated peer grades, faculty member grading, peer critique, and faculty member-guided discussion of drug information responses. Annual instructor and course evaluations consistently revealed favorable student feedback regarding workshop value. A drug information workshop series using peer-grading as the primary assessment tool was successfully implemented and was well received by pharmacy students.

What's Holding Back Social Entrepreneurship? Removing the Impediments to Theoretical Advancement

NARCIS (Netherlands)

Mueller, Susan; D'Intino, Robert S.; Walske, Jennifer; Ehrenhard, Michel Léon; Newbert, Scott L.; Robinson, Jeffrey A.; Senjem, Jason C.

2015-01-01

This article summarizes four contributions that were presented in a professional development workshop at the 2013 Academy of Management conference. The goal of the workshop was to discuss impediments to the theoretical advancement of social entrepreneurship. This paper's first two contributors

Creating Fantastic PI Workshops

Energy Technology Data Exchange (ETDEWEB)

Biedermann, Laura B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Clark, Blythe G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Colbert, Rachel S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dagel, Amber Lynn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gupta, Vipin P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hibbs, Michael R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Perkins, David Nikolaus [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); West, Roger Derek [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-10-01

The goal of this SAND report is to provide guidance for other groups hosting workshops and peerto-peer learning events at Sandia. Thus this SAND report provides detail about our team structure, how we brainstormed workshop topics and developed the workshop structure. A Workshop “Nuts and Bolts” section provides our timeline and check-list for workshop activities. The survey section provides examples of the questions we asked and how we adapted the workshop in response to the feedback.

Study of the reservoirs of Jurassic and Cretaceous periods in the south-cast slope of Central Kara-Kum vault using combination of acoustic logging, neutron-gamma logging, gamma logging, and electrical logging

International Nuclear Information System (INIS)

Meredov, T.M.; Baranov, M.I.

1978-01-01

Considered is the possibility of application of the combination of neutron-gamma logging, gamma logging al partitioncoustic logging and electrical logging to lithologica of sections, discovery reservoir layers in carbonate and terrigeneous sections as well as quantitative estimation of the porosity coefficients values at prospecting areas in the south-east slope of Central Kara-Kum vault. Neutron-gamma logging mostly makes it possible to partition carbonate rocks into limestones, dolomites and their interstitial variaties and to indicate sand stone layers with different degree of carbonate content

"Good Vibrations": A workshop on oscillations and normal modes

Science.gov (United States)

Barbieri, Sara; Carpineti, Marina; Giliberti, Marco; Rigon, Enrico; Stellato, Marco; Tamborini, Marina

2016-05-01

We describe some theatrical strategies adopted in a two hour workshop in order to show some meaningful experiments and the underlying useful ideas to describe a secondary school path on oscillations, that develops from harmonic motion to normal modes of oscillations, and makes extensive use of video analysis, data logging, slow motions and applet simulations. Theatre is an extremely useful tool to stimulate motivation starting from positive emotions. That is the reason why the theatrical approach to the presentation of physical themes has been explored by the group "Lo spettacolo della Fisica" (http://spettacolo.fisica.unimi.it) of the Physics Department of University of Milano for the last ten years (Carpineti et al., JCOM, 10 (2011) 1; Nuovo Cimento B, 121 (2006) 901) and has been inserted also in the European FP7 Project TEMI (Teaching Enquiry with Mysteries Incorporated, see http://teachingmysteries.eu/en) which involves 13 different partners coming from 11 European countries, among which the Italian (Milan) group. According to the TEMI guidelines, this workshop has a written script based on emotionally engaging activities of presenting mysteries to be solved while participants have been involved in nice experiments following the developed path.

Developing Mentoring Competency: Does a One Session Training Workshop Have Impact?

Science.gov (United States)

Lau, Chloe; Ford, Jennifer; Van Lieshout, Ryan J; Saperson, Karen; McConnell, Meghan; McCabe, Randi

2016-06-01

Mentorship remains vital to the career development, research productivity, and professional advancement of healthcare professionals in all disciplines of academic medicine. Recent studies describe mentor training initiatives aimed at increasing mentoring competency through multisession training curricula. Although the published results of these programs are promising, they require the following: (1) substantial financial resources from the institution, and (2) continuous participation and time commitment from faculty, which may reduce participation and effectiveness. A single, half-day of evidence-based mentor training would represent a more cost-effective and accessible option for educating mentors. The present study investigates the impact of a half-day interactive mentor training workshop on mentoring competency in faculty, staff, and trainees of the Department of Psychiatry and Behavioural Neurosciences at McMaster University. Overall, participants' self-reported mentoring competency mean scores were significantly higher post-workshop compared to pre-workshop ratings [mean = 4.48 vs. 5.02 pre- and post-workshop, respectively; F(1, 31) = 18.386, P < 0.001, η p2 = 0.37]. Survey respondents gave positive feedback and reported greater understanding of mentorship and specific mentoring changes they planned to apply after attending the workshop. Academic and healthcare institutions may use this framework to guide the development of a half-day mentoring workshop into their education programs.

Proceedings of the 1986 workshop on advanced time-of-flight neutron powder diffraction

International Nuclear Information System (INIS)

Lawson, A.C.; Smith, K.

1986-09-01

This report contains abstracts of talks and summaries of discussions from a small workshop held to discuss the future of time-of-flight neutron powder diffraction and its implementation at the Los Alamos Neutron Scattering Center. 47 refs., 3 figs

Proceedings of the 1986 workshop on advanced time-of-flight neutron powder diffraction

Energy Technology Data Exchange (ETDEWEB)

Lawson, A.C.; Smith, K. (comps.)

1986-09-01

This report contains abstracts of talks and summaries of discussions from a small workshop held to discuss the future of time-of-flight neutron powder diffraction and its implementation at the Los Alamos Neutron Scattering Center. 47 refs., 3 figs.

MO-AB-210-03: Workshop

International Nuclear Information System (INIS)

Lu, Z.

2015-01-01

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

The Meaning of Logs

NARCIS (Netherlands)

Etalle, Sandro; Massacci, Fabio; Yautsiukhin, Artsiom

2007-01-01

While logging events is becoming increasingly common in computing, in communication and in collaborative work, log systems need to satisfy increasingly challenging (if not conflicting) requirements.Despite the growing pervasiveness of log systems, to date there is no high-level framework which

The Meaning of Logs

NARCIS (Netherlands)

Etalle, Sandro; Massacci, Fabio; Yautsiukhin, Artsiom; Lambrinoudakis, Costas; Pernul, Günther; Tjoa, A Min

While logging events is becoming increasingly common in computing, in communication and in collaborative environments, log systems need to satisfy increasingly challenging (if not conflicting) requirements. In this paper we propose a high-level framework for modeling log systems, and reasoning about

Workshop report on new directions in x-ray scattering

International Nuclear Information System (INIS)

Brown, G.; Del Grande, N.K.; Fuoss, P.; Mallett, J.H.; Pratt, R.; Templeton, D.

1987-01-01

This report is a summary of the Workshop on New Directions in X-Ray Scattering held at the Asilomar Conference Center, Pacific Grove, California, April 2-5, 1985. The report primarily consists of the edited transcript of the final review session of the workshop, in which members of a panel summarized the proceedings. It is clear that we are close to achieving an accurate theory of scattering in independent particle approximation, but for edge regions, there is need to go beyond this approach. Much of what is experimentally interesting in scattering is occurring between the photoabsorption edge and the photoelectric threshold. Applications in condensed matter and biological and chemical material studies are expanding, exploiting higher intensity sources and faster time resolution as in magnetic scattering and surface studies. Storage rings are now conventional sources, and new high-intensity beam lines are under development; the free electron laser is one of the more speculative sources. Recent work in x-ray scattering has led to advances in x-ray optics, and conversely, advances in x-ray optics have benefitted our understanding of x-ray scattering

Proceedings of the 42nd basic science seminar. (The 7th workshop on neutron crystallography in biology)

International Nuclear Information System (INIS)

Niimura, Nobuo

1996-02-01

42nd advanced science seminar (the 7th workshop on neutron crystallography in biology) was held on October, 25-26, 1995 at Tokai. Forty three participants from university, research institute and private company took part in the workshop and there were 17 lectures given. The proceedings collect the figures and tables which the speakers used in their lectures. (author)

The fourth international energy agency international workshop on beryllium technology for fusion

International Nuclear Information System (INIS)

Scaffidi-Argentina, F.; Longhurst, G.R.

2000-01-01

The main objective of the workshop was to support the advancement of the international development of fusion power through communication and dissemination of information on progress made in beryllium technology. This has been accomplished through presentation of original research on issues of current interest to the fusion beryllium community. The workshop was divided into ten technical sessions that addressed the following general topics: production and characterization, health and safety, forming and joining, chemical compatibility, thermal-mechanical properties, pebble bed behavior, high-heat-flux performance, irradiation effects, plasma-tritium interaction, and molten beryllium-bearing salts

The fourth international energy agency international workshop on beryllium technology for fusion

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F.; Longhurst, G.R.

2000-05-01

The main objective of the workshop was to support the advancement of the international development of fusion power through communication and dissemination of information on progress made in beryllium technology. This has been accomplished through presentation of original research on issues of current interest to the fusion beryllium community. The workshop was divided into ten technical sessions that addressed the following general topics: production and characterization, health and safety, forming and joining, chemical compatibility, thermal-mechanical properties, pebble bed behavior, high-heat-flux performance, irradiation effects, plasma-tritium interaction, and molten beryllium-bearing salts.

Genetic Engineering Workshop Report, 2010

Energy Technology Data Exchange (ETDEWEB)

Allen, J; Slezak, T

2010-11-03

The Lawrence Livermore National Laboratory (LLNL) Bioinformatics group has recently taken on a role in DTRA's Transformation Medical Technologies (TMT) program. The high-level goal of TMT is to accelerate the development of broad-spectrum countermeasures. To achieve this goal, there is a need to assess the genetic engineering (GE) approaches, potential application as well as detection and mitigation strategies. LLNL was tasked to coordinate a workshop to determine the scope of investments that DTRA should make to stay current with the rapid advances in genetic engineering technologies, so that accidental or malicious uses of GE technologies could be adequately detected and characterized. Attachment A is an earlier report produced by LLNL for TMT that provides some relevant background on Genetic Engineering detection. A workshop was held on September 23-24, 2010 in Springfield, Virginia. It was attended by a total of 55 people (see Attachment B). Twenty four (44%) of the attendees were academic researchers involved in GE or bioinformatics technology, 6 (11%) were from DTRA or the TMT program management, 7 (13%) were current TMT performers (including Jonathan Allen and Tom Slezak of LLNL who hosted the workshop), 11 (20%) were from other Federal agencies, and 7 (13%) were from industries that are involved in genetic engineering. Several attendees could be placed in multiple categories. There were 26 attendees (47%) who were from out of the DC area and received travel assistance through Invitational Travel Orders (ITOs). We note that this workshop could not have been as successful without the ability to invite experts from outside of the Beltway region. This workshop was an unclassified discussion of the science behind current genetic engineering capabilities. US citizenship was not required for attendance. While this may have limited some discussions concerning risk, we felt that it was more important for this first workshop to focus on the scientific state of

Externally predictive single-descriptor based QSPRs for physico-chemical properties of polychlorinated-naphthalenes: Exploring relationships of log SW, log KOA, and log KOW with electron-correlation

International Nuclear Information System (INIS)

Chayawan; Vikas

2015-01-01

Highlights: • Aqueous solubility and partition coefficient are modelled using single-parameter. • Electron-correlation observed as a vital predictorof physico-chemical properties. • For octanol-air partition coefficient, energy and polarizability yield best models. • Dipole-moment is found to be worst single-descriptor for the properties analysed. - Abstract: Quantitative structure–property relationships (QSPRs), based only on a single-parameter, are proposed for the prediction of physico-chemical properties, namely, aqueous solubility (log S W ), octanol–water partition coefficient (log K OW ) and octanol–air partition coefficient (log K OA ) of polychloronaphthalenes (PCNs) including all the 75 chloronaphthalene congeners. The QSPR models are developed using molecular descriptors computed through quantum mechanical methods including ab-initio as well as advanced semi-empirical methods. The predictivity of the developed models is tested through state-of-the-art external validation procedures employing an external prediction set of compounds. To analyse the role of instantaneous interactions between electrons (the electron-correlation), the models are also compared with those developed using only the electron-correlation contribution of the quantum chemical descriptor. The electron-correlation contribution towards the chemical hardness and the LUMO energy are observed to be the best predictors for octanol–water partition coefficient, whereas for the octanol–air partition coefficient, the total electronic energy and electron-correlation energy are found to be reliable descriptors, in fact, even better than the polarisability. For aqueous solubility of PCNs, the absolute electronegativity is observed to be the best predictor. This work suggests that the electron-correlation contribution of a quantum-chemical descriptor can be used as a reliable indicator for physico-chemical properties, particularly the partition coefficients

A mixed-methods analysis of logging injuries in Montana and Idaho.

Science.gov (United States)

Lagerstrom, Elise; Magzamen, Sheryl; Rosecrance, John

2017-12-01

Despite advances in mechanization, logging continues to be one of the most dangerous occupations in the United States. Logging in the Intermountain West region (Montana and Idaho) is especially hazardous due to steep terrain, extreme weather, and remote work locations. We implemented a mixed-methods approach combining analyses of workers' compensation claims and focus groups to identify factors associated with injuries and fatalities in the logging industry. Inexperienced workers (>6 months experience) accounted for over 25% of claims. Sprain/strain injuries were the most common, accounting for 36% of claims, while fatalities had the highest median claim cost ($274 411). Focus groups identified job tasks involving felling trees, skidding, and truck driving as having highest risk. Injury prevention efforts should focus on training related to safe work methods (especially for inexperienced workers), the development of a safety culture and safety leadership, as well as implementation of engineering controls. © 2017 Wiley Periodicals, Inc.

afnog 2008 workshop & meetings held at golden tulip farah rabat ...

International Development Research Centre (IDRC) Digital Library (Canada)

nancy

The resultant effect is that today, several Internet Service Providers and large ... AfNOG Workshop aims to offer advanced training to operators of existing African ... AfNOG is exploring with Partners how best to teach this track in countries ... scaling customer and end user support, implementing network security tools and.

Technology Evaluation Workshop Report for Tank Waste Chemical Characterization

International Nuclear Information System (INIS)

Eberlein, S.J.

1994-04-01

A Tank Waste Chemical Characterization Technology Evaluation Workshop was held August 24--26, 1993. The workshop was intended to identify and evaluate technologies appropriate for the in situ and hot cell characterization of the chemical composition of Hanford waste tank materials. The participants were asked to identify technologies that show applicability to the needs and good prospects for deployment in the hot cell or tanks. They were also asked to identify the tasks required to pursue the development of specific technologies to deployment readiness. This report describes the findings of the workshop. Three focus areas were identified for detailed discussion: (1) elemental analysis, (2) molecular analysis, and (3) gas analysis. The technologies were restricted to those which do not require sample preparation. Attachment 1 contains the final workshop agenda and a complete list of attendees. An information package (Attachment 2) was provided to all participants in advance to provide information about the Hanford tank environment, needs, current characterization practices, potential deployment approaches, and the evaluation procedure. The participants also received a summary of potential technologies (Attachment 3). The workshop opened with a plenary session, describing the background and issues in more detail. Copies of these presentations are contained in Attachments 4, 5 and 6. This session was followed by breakout sessions in each of the three focus areas. The workshop closed with a plenary session where each focus group presented its findings. This report summarizes the findings of each of the focus groups. The evaluation criteria and information about specific technologies are tabulated at the end of each section in the report. The detailed notes from each focus group are contained in Attachments 7, 8 and 9

WWER-1000 reactor simulator. Material for training courses and workshops. 2. ed

International Nuclear Information System (INIS)

2005-01-01

The International Atomic Energy Agency (IAEA) has established an activity in nuclear reactor simulation computer programs to assist its Member States in education. The objective is to provide, for a variety of advanced reactor types, insight and practice in their operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the development and distribution of simulation programs and educational material and sponsors courses and workshops. The workshops are in two parts: techniques and tools for reactor simulator development; and the use of reactor simulators in education. Workshop material for the first part is covered in the IAEA publication: Training Course Series No.12, Reactor Simulator Development (2001). Course material for workshops using a pressurized water reactor (PWR) simulator developed for the IAEA by Cassiopeia Technologies Inc. of Canada is presented in the IAEA publication, Training Course Series No. 22, 2nd edition, Pressurized Water Reactor Simulator (2005) and Training Course Series No.23, 2nd edition, Boiling Water Reactor Simulator (2005). This report consists of course material for workshops using the WWER-1000 Reactor Department Simulator from the Moscow Engineering and Physics Institute, Russian Federation

SDSS Log Viewer: visual exploratory analysis of large-volume SQL log data

Science.gov (United States)

Zhang, Jian; Chen, Chaomei; Vogeley, Michael S.; Pan, Danny; Thakar, Ani; Raddick, Jordan

2012-01-01

User-generated Structured Query Language (SQL) queries are a rich source of information for database analysts, information scientists, and the end users of databases. In this study a group of scientists in astronomy and computer and information scientists work together to analyze a large volume of SQL log data generated by users of the Sloan Digital Sky Survey (SDSS) data archive in order to better understand users' data seeking behavior. While statistical analysis of such logs is useful at aggregated levels, efficiently exploring specific patterns of queries is often a challenging task due to the typically large volume of the data, multivariate features, and data requirements specified in SQL queries. To enable and facilitate effective and efficient exploration of the SDSS log data, we designed an interactive visualization tool, called the SDSS Log Viewer, which integrates time series visualization, text visualization, and dynamic query techniques. We describe two analysis scenarios of visual exploration of SDSS log data, including understanding unusually high daily query traffic and modeling the types of data seeking behaviors of massive query generators. The two scenarios demonstrate that the SDSS Log Viewer provides a novel and potentially valuable approach to support these targeted tasks.

1994 DOE Technical Standards Program Workshop: Proceedings

International Nuclear Information System (INIS)

Spellman, D.J.

1994-01-01

The DOE Technical Standards Program has been structured to provide guidance and assistance for the development, adoption, and use of voluntary standards within the Department. OMB Circular A-119, ''Federal Participation in the Development and Use of Voluntary Standards'' establishes the policy to be followed in working with voluntary standards bodies, and in adopting and using voluntary standards whenever feasible. The DOE Technical Standards Program is consistent with this policy and is dedicated to the task of promoting its implementation. The theme of this year's workshop is ''Standards Initiatives in Environmental Management fostering the development and use of industry standards for safe, environmentally responsible operations.'' The objective of the workshop is to increase the participant's awareness of the standardization activities taking place nationally and internationally and the impact of these activities on their efforts, and to facilitate the exchange of experiences, processes, and tools for implementing the program. Workshop sessions will include presentations by industry and Government notables in the environment, safety, and health arena with ample opportunity for everyone to ask questions and share experiences. There will be a breakout session which will concentrate on resolution of issues arising from the implementation of the DOE Technical Standards Program and a plenary session to discuss the plans developed by the breakout groups. Many organizations provide services and products which support the development, processing, distribution, and retrieval of standards. Those organizations listed at the end of the agenda will have exhibits available for your perusal throughout the workshop. Last year's workshop was very successful in stimulating an understanding of an interest in the standards program. This year, we hope to build on that success and provide an environment for the synergism of ideas to enhance the program and advance its implementation

Advanced Electron Microscopy in Materials Physics

International Nuclear Information System (INIS)

Zhu, Y.; Jarausch, K.

2009-01-01

Aberration correction has opened a new frontier in electron microscopy by overcoming the limitations of conventional round lenses, providing sub-angstrom-sized probes and extending information limits. The imaging and analytical performance of these corrector-equipped microscopes affords an unprecedented opportunity to study structure-property relationships of matter at the atomic scale. This new generation of microscopes is able to retrieve high-quality structural information comparable to neutron and synchrotron x-ray experiments, but with local atomic resolution. These advances in instrumentation are accelerating the research and development of various functional materials ranging from those for energy generation, conversion, transportation and storage to those for catalysis and nano-device applications. The dramatic improvements in electron-beam illumination and detection also present a host of new challenges for the interpretation and optimization of experiments. During 7-9 November 2007, a workshop, entitled 'Aberration Corrected Electron Microscopy in Material Physics', was convened at the Center for Functional Nanomaterials, Brookhaven National Laboratories (BNL) to address these opportunities and challenges. The workshop was co-sponsored by Hitachi High Technologies, a leader in electron microscopy instrumentation, and BNL's Institute of Advanced Electron Microscopy, a leader in materials physics research using electron microscopy. The workshop featured presentations by internationally prominent scientists working at the frontiers of electron microscopy, both on developing instrumentation and applying it in materials physics. The meeting, structured to stimulate scientific exchanges and explore new capabilities, brought together ∼100 people from over 10 countries. This special issue complies many of the advances in instrument performance and materials physics reported by the invited speakers and attendees at the workshop.

Workshops as a Research Methodology

Science.gov (United States)

Ørngreen, Rikke; Levinsen, Karin

2017-01-01

This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on…

NATO Advanced Research Workshop on Molecular Engineering for Advanced Materials

CERN Document Server

Schaumburg, Kjeld

1995-01-01

An important aspect of molecular engineering is the `property directed' synthesis of large molecules and molecular assemblies. Synthetic expertise has advanced to a state which allows the assembly of supramolecules containing thousands of atoms using a `construction kit' of molecular building blocks. Expansion in the field is driven by the appearance of new building blocks and by an improved understanding of the rules for joining them in the design of nanometer-sized devices. Another aspect is the transition from supramolecules to materials. At present no single molecule (however large) has been demonstrated to function as a device, but this appears to be only a matter of time. In all of this research, which has a strongly multidisciplinary character, both existing and yet to be developed analytical techniques are and will remain indispensable. All this and more is discussed in Molecular Engineering for Advanced Materials, which provides a masterly and up to date summary of one of the most challenging researc...

Static dictionaries on AC⁰ RAMs: query time (√log n/log log n) is necessary and sufficient

DEFF Research Database (Denmark)

Andersson, Arne; Miltersen, Peter Bro; Riis, Søren

1996-01-01

) on the time for answering membership queries in a set of size n when reasonable space is used for the data structure storing the set; the upper bound can be obtained using O(n) space, and the lower bound holds even if we allow space 2polylog n. Several variations of this result are also obtained. Among others......, we show a tradeoff between time and circuit depth under the unit-cost assumption: any RAM instruction set which permits a linear space, constant query time solution to the static dictionary problem must have an instruction of depth Ω(log w/log log to), where w is the word size of the machine (and log...

Summary of the 2012 Wide Area Recovery and Resiliency Program (WARRP) Waste Management Workshop

Science.gov (United States)

Workshop advanced the planning of federal, state and local officials in the area of waste management following a chemical, biological or radiological wide-area incident in the Denver, Colorado urban area.

Improved trip generation data for Texas using workplace and special generator surveys : workshop materials.

Science.gov (United States)

2014-08-01

Workshop Objectives: : Present Texas Trip Generation Manual : How developed : How it can be used, built upon : Provide examples and discuss : Present Generic WP Attraction Rates : Review Trip Attractions and Advanced Models

Summary Report of Advanced Hydropower Innovations and Cost Reduction Workshop at Arlington, VA, November 5 & 6, 2015

Energy Technology Data Exchange (ETDEWEB)

O' Connor, Patrick [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Rugani, Kelsey [Kearns & West, Inc., San Francisco, CA (United States); West, Anna [Kearns & West, Inc., San Francisco, CA (United States)

2016-03-01

On behalf of the U.S. Department of Energy (DOE) Wind and Water Power Technology Office (WWPTO), Oak Ridge National Laboratory (ORNL), hosted a day and half long workshop on November 5 and 6, 2015 in the Washington, D.C. metro area to discuss cost reduction opportunities in the development of hydropower projects. The workshop had a further targeted focus on the costs of small, low-head1 facilities at both non-powered dams (NPDs) and along undeveloped stream reaches (also known as New Stream-Reach Development or “NSD”). Workshop participants included a cross-section of seasoned experts, including project owners and developers, engineering and construction experts, conventional and next-generation equipment manufacturers, and others to identify the most promising ways to reduce costs and achieve improvements for hydropower projects.

16th Workshop on Crystalline Silicon Solar Cells and Modules: Materials and Processes; Program, Extended Abstracts, and Papers

Energy Technology Data Exchange (ETDEWEB)

Sopori, B. L.

2006-08-01

The National Center for Photovoltaics sponsored the 16th Workshop on Crystalline Silicon Solar Cells and Modules: Materials and Processes held August 6-9, 2006 in Denver, Colorado. The workshop addressed the fundamental properties of PV-Si, new solar cell designs, and advanced solar cell processing techniques. It provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. The Workshop Theme was: "Getting more (Watts) for Less ($i)". A combination of oral presentations by invited speakers, poster sessions, and discussion sessions reviewed recent advances in crystal growth, new cell structures, new processes and process characterization techniques, and cell fabrication approaches suitable for future manufacturing demands. The special sessions included: Feedstock Issues: Si Refining and Purification; Metal-impurity Engineering; Thin Film Si; and Diagnostic Techniques.

Processing well logging data, for example for verification and calibration of well logs

International Nuclear Information System (INIS)

Suau, J.; Boutemy, Y.

1981-01-01

A method is described of machine processing well logging data derived from borehole exploring devices which investigate earth formations traversed by boreholes. The method can be used for verifying and recalibrating logs, reconstructing missing logs and combining the data to form a statistical model of the traversed earth formations. (U.K.)

Proceedings of the switched power workshop

International Nuclear Information System (INIS)

Fernow, R.C.

1988-01-01

These proceedings contain most of the presentations given at a workshop on the current state of research in techniques for switched power acceleration. The proceedings are divided, as was the workshop itself, into two parts. Part 1, contains the latest results from a number of groups active in switched power research. The major topic here is a method for switching externally supplied power onto a transmission line. Advocates for vacuum photodiode switching, solid state switching, gas switching, and synthetic pulse generation are all presented. Other important areas of research described in this section concern: external electrical and laser pulsing systems; the properties of the created electromagnetic pulse; structures used for transporting the electromagnetic pulse to the region where the electron beam is located; and possible applications. Part 2 of the proceedings considers the problem of designing a high brightness electron gun using switched power as the power source. This is an important first step in demonstrating the usefulness of switched power techniques for accelerator physics. In addition such a gun could have immediate practical importance for advanced acceleration studies since the brightness could exceed that of present sources by several orders of magnitude. I would like to take this opportunity to thank Kathleen Tuohy and Patricia Tuttle for their assistance in organizing and running the workshop. Their tireless efforts contribute greatly to a very productive meeting

La logística integral como ventaja competitiva y sistema logístico

Directory of Open Access Journals (Sweden)

Mario Anselmo Martínez gallardo

2013-07-01

Full Text Available Esta investigación analiza la logística integral como una ventaja competitiva y el sistema logístico. Es opinión de los autores que la logística integral es esencial para el intercambio de mercancías, toda vez que reduce costos y hace más ágil la actividad comercial. La utilización de esta logística representa una ventaja competitiva con respecto de otras empresas por la optimización del capital y ahorro de tiempo.

Proceedings of DAE-BRNS national workshop on materials chemistry: functional materials

International Nuclear Information System (INIS)

2011-12-01

Design and development of materials with tailored properties assumes great significance in our everyday life and are crucial to modern technologies. Chemistry has had a tremendous Convener role in developing several need based materials by integrating multiple functionalities. The year 2011, being recognised as the International Year of Chemistry by the UNESCO, assumes further significance for material chemists. In view of the renowned interest in advanced functional materials, the Society for Materials Chemistry, India together with Chemistry Division, BARC has taken an initiative to organise this National Workshop on Materials Chemistry (NWMC-2011) under the theme 'Functional Materials (FUN-MAT)'. NWMC- 2011 aims to provide a forum for young researchers to interact with experts involved in synthesis, processing and applications of various advanced functional materials. In particular, recent developments and future prospects of magnetic, electronic and optical materials, glasses, ceramics, soft materials, materials for sensors, materials for hydrogen production and storage etc. will be addressed in this workshop. Papers relevant to INIS are indexed separately

Sandia National Laboratories Strategic Context Workshop Series 2017: National Security Futures for Strategic Thinking.

Energy Technology Data Exchange (ETDEWEB)

Keller, Elizabeth James Kistin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Roll, Elizabeth [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Aamir, Munaf Syed [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Deland, Sharon M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Haddal, Chad [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Passell, Howard D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Foley, John T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Harwell, Amber Suzanne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Otis, Monique [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Backus, George A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Wendell [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bawden, Michael Greet Shander [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Craft, Richard L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kistin, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martin, Jeffrey B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McNicol, Bradley Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vannoni, Michael G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trost, Lawrence C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Tsao, Jeffrey Y. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Weaver, Karla [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-01-01

In August 2017, Sandia convened five workshops to explore the future of advanced technologies and global peace and security through the lenses of deterrence, information, innovation, nonproliferation, and population and Earth systems.

Advances in Chance Discovery : Extended Selection from International Workshops

CERN Document Server

Abe, Akinori

2013-01-01

Since year 2000, scientists on artificial and natural intelligences started to study chance discovery - methods for discovering events/situations that significantly affect decision making. Partially because the editors Ohsawa and Abe are teaching at schools of Engineering and of Literature with sharing the interest in chance discovery, this book reflects interdisciplinary aspects of progress: First, as an interdisciplinary melting pot of cognitive science, computational intelligence, data mining/visualization, collective intelligence, … etc, chance discovery came to reach new application domains e.g. health care, aircraft control, energy plant, management of technologies, product designs, innovations, marketing, finance etc. Second, basic technologies and sciences including sensor technologies, medical sciences, communication technologies etc. joined this field and interacted with cognitive/computational scientists in workshops on chance discovery, to obtain breakthroughs by stimulating each other. Third, �...

Improving patient outcomes in fibrous dysplasia/McCune-Albright syndrome: an international multidisciplinary workshop to inform an international partnership.

Science.gov (United States)

Boyce, A M; Turner, A; Watts, L; Forestier-Zhang, L; Underhill, A; Pinedo-Villanueva, R; Monsell, F; Tessaris, D; Burren, C; Masi, L; Hamdy, N; Brandi, M L; Chapurlat, R; Collins, M T; Javaid, Muhammad Kassim

2017-12-01

To develop consensus on improving the management of patients, we convened an international workshop involving patients, clinicians, and researchers. Key findings included the diagnostic delay and variability in subsequent management with agreement to develop an international natural history study. We now invite other stakeholders to join the partnership. The aim of this study was develop a consensus on how to improve the management of patients with fibrous dysplasia and prioritize areas for research METHODS: An international workshop was held over 3 days involving patients, clinicians, and researchers. Each day had a combination of formal presentations and facilitated discussions that focused on clinical pathways and research. The patient workshop day highlighted the variability of patients' experience in getting a diagnosis, the knowledge of general clinical staff, and understanding long-term outcomes. The research workshop prioritized collaborations that improved understanding of the contemporary natural history of fibrous dysplasia/McCune-Albright syndrome (FD/MAS). The clinical workshop outlined the key issues around diagnostics, assessment of severity, treatment and monitoring of patients. In spite of advances in understanding the genetic and molecular underpinnings of fibrous dysplasia/McCune-Albright syndrome, clinical management remains a challenge. From the workshop, a consensus was reached to create an international, multi-stakeholder partnership to advance research and clinical care in FD/MAS. We invite other stakeholders to join the partnership.

MOOC Design Workshop

DEFF Research Database (Denmark)

Nørgård, Rikke Toft; Mor, Yishay; Warburton, Steven

2016-01-01

For the last two years we have been running a series of successful MOOC design workshops. These workshops build on previous work in learning design and MOOC design patterns. The aim of these workshops is to aid practitioners in defining and conceptualising educational innovations (predominantly......, but not exclusively MOOCs) which are based on an empathic user-centered view of the target learners and teachers. In this paper, we share the main principles, patterns and resources of our workshops and present some initial results for their effectiveness...

1993 CAT workshop on beamline optical designs

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

An Advanced Photon Source (APS) Collaborative Access Team (CAT) Workshop on Beamline Optical Designs was held at Argonne National Laboratory on July 26--27, 1993. The goal of this workshop was to bring together experts from various synchrotron sources to provide status reports on crystal, reflecting, and polarizing optics as a baseline for discussions of issues facing optical designers for CAT beamlines at the APS. Speakers from the European Synchrotron Radiation Facility (ESRF), the University of Chicago, the National Synchrotron Light Source, and the University of Manchester (England) described single- and double-crystal monochromators, mirrors, glass capillaries, and polarizing optics. Following these presentations, the 90 participants divided into three working groups: Crystal Optics Design, Reflecting Optics, and Optics for Polarization Studies. This volume contains copies of the presentation materials from all speakers, summaries of the three working groups, and a ``catalog`` of various monochromator designs.

1993 CAT workshop on beamline optical designs

International Nuclear Information System (INIS)

1993-11-01

An Advanced Photon Source (APS) Collaborative Access Team (CAT) Workshop on Beamline Optical Designs was held at Argonne National Laboratory on July 26--27, 1993. The goal of this workshop was to bring together experts from various synchrotron sources to provide status reports on crystal, reflecting, and polarizing optics as a baseline for discussions of issues facing optical designers for CAT beamlines at the APS. Speakers from the European Synchrotron Radiation Facility (ESRF), the University of Chicago, the National Synchrotron Light Source, and the University of Manchester (England) described single- and double-crystal monochromators, mirrors, glass capillaries, and polarizing optics. Following these presentations, the 90 participants divided into three working groups: Crystal Optics Design, Reflecting Optics, and Optics for Polarization Studies. This volume contains copies of the presentation materials from all speakers, summaries of the three working groups, and a ''catalog'' of various monochromator designs

Hydrophysical logging: A new wellbore technology for hydrogeologic and contaminant characterization of aquifers

International Nuclear Information System (INIS)

Pedler, W.H.; Williams, L.L.; Head, C.L.

1992-01-01

In the continuing search for improved groundwater characterization technologies, a new wellbore fluid logging method has recently been developed to provide accurate and cost effective hydrogeologic and contaminant characterization of bedrock aquifers. This new technique, termed hydrophysical logging, provides critical information for contaminated site characterization and water supply studies and, in addition, offers advantages compared to existing industry standards for aquifer characterization. Hydrophysical logging is based on measuring induced electrical conductivity changes in the fluid column of a wellbore by employing advanced downhole water quality instrumentation specifically developed for the dynamic borehole environment. Hydrophysical logging contemporaneously identifies the locations of water bearing intervals, the interval-specific inflow rate during pumping, and in-situ hydrochemistry of the formation waters associated with each producing interval. In addition, by employing a discrete point downhole fluid sampler during hydrophysical logging, this technique provides evaluation of contaminant concentrations and migration of contaminants vertically within the borehole. Recently, hydrophysical logging was applied in a deep bedrock wellbore at an industrial site in New Hampshire contaminated with dense nonaqueous phase liquids (DNAPLs). The results of the hydrophysical logging, conducted as part of a hydrogeologic site investigation and feasibility study, facilitated investigation of the site by providing information which indicated that the contamination had not penetrated into deeper bedrock fractures at concentrations of concern. This information was used to focus the pending Remedial Action Plan and to provide a more cost-effective remedial design

Interactive Forms of Open Scientific and Educational Workshop

Directory of Open Access Journals (Sweden)

Naumova Galina Alekseevna

2014-12-01

Full Text Available The article discusses the innovative chain of the Russian economy which consists of three stages: “Idea” (academic science, “Technology” (applied science, and “Production”. The authors describe the innovative system of Russia in terms of infrastructure devices, the functioning of the financial system and human resources. Special attention is paid to the problem of staff training for the innovation economy in Russia. The authors propose the use of scientific and educational public workshop as a form of interactive courses in training staff for the “economy of knowledge”. The article describes the experience of holding open seminars at the Department of Innovation Studies of Volgograd State University. The members of project teams of scientific and Interdisciplinary Innovative Design educational center take part in these discussions. Four scenarios of public workshops are suggested. The first one refers to the joint research work of students, undergraduates and graduate students. The activity includes the presentation of research projects, collective work of students in the creation of business models, innovative projects, debates in the format of a talk show on current topics in the field of innovation and business. The participants also discuss the latest technological and scientific advances in the field of innovations with practical application in business by means of webinars. The second scenario implies an open workshop in the form of presentation of research results based on the technology of group project-based learning as an interactive method which is widely used in the leading universities of the world, and is the organization of educational process in the form of implementation of group projects, from the stage of their development to practical implementation. Team work (“brainstorming” open workshop consists in the creation of business models, innovative projects based on the use of techniques of prominent

Neutron Characterization of Additively Manufactured Components. Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Watkins, Thomas R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Payzant, E. Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Babu, Sudarsanam Suresh [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

Additive manufacturing (AM) is a collection of promising manufacturing methods that industry is beginning to explore and adopt. Macroscopically complicated and near net shape components are being built using AM, but how the material behaves in service is a big question for industry. Consequently, AM components/materials need further research into exactly what is made and how it will behave in service. This one and a half day workshop included a series of invited presentations from academia, industry and national laboratories (see Appendix A for the workshop agenda and list of talks). The workshop was welcomed by Alan Tennant, Chief Scientist, Neutron Sciences Directorate, ORNL, and opened remotely by Rob Ivestor, Deputy Director, Advanced Manufacturing Office-DOE, who declared AM adoptees as titans who will be able to create customized 3-D structures with 1 million to 1 billion micro welds with locally tailored microstructures. Further he stated that characterization with neutrons is key to be able to bring critical insight/information into the AM process/property/behavior relationship. Subsequently, the presentations spanned a slice of the current state of the art AM techniques and many of the most relevant characterization techniques using neutrons. After the talks, a panel discussion was held; workshop participants (see Appendix B for a list of attendees) providing questions and the panel answers. The main purpose of the panel discussion was to build consensus regarding the critical research needs in AM that can be addressed with neutrons. These needs were placed into three categories: modes of access for neutrons, new capabilities needed, new AM material issues and neutrons. Recommendations from the workshop were determined based on the panel discussion.

The log S -log N distribution of gamma ray brust

International Nuclear Information System (INIS)

Yamagami, Takamasa; Nishimura, Jun; Fujii, Masami

1982-01-01

The relation between the size S and the frequency N of gamma ray burst has been studied. This relation may be determined from the celestial distribution of gamma ray burst sources. The present analysis gives that the log S - log N relation for any direction is determined by the celestial distribution of gamma ray burst sources. The observed bursts were analyzed. The celestial distribution of gamma ray burst sources was observed by the satellites of USSR. The results showed that the distribution seemed to be isotropic. However, the calculated log S - log N relation based on the isotropic distribution wasF in disagreement with the observed ones. As the result of analysis, it was found that the observed bursts missed low energy part because of the threshold of detectors. The levels of discrimination of detection were not clear. When a proper threshold level is set for each type of burst, and the size of bursts is determined, the above mentioned discrepancy will be deleted regardless of luminosity and the spatial distribution of bursts. (Kato, T.)

Digital mineral logging system

International Nuclear Information System (INIS)

West, J.B.

1980-01-01

A digital mineral logging system acquires data from a mineral logging tool passing through a borehole and transmits the data uphole to an electronic digital signal processor. A predetermined combination of sensors, including a deviometer, is located in a logging tool for the acquisition of the desired data as the logging tool is raised from the borehole. Sensor data in analog format is converted in the logging tool to a digital format and periodically batch transmitted to the surface at a predetermined sampling rate. An identification code is provided for each mineral logging tool, and the code is transmitted to the surface along with the sensor data. The self-identifying tool code is transmitted to the digital signal processor to identify the code against a stored list of the range of numbers assigned to that type of tool. The data is transmitted up the d-c power lines of the tool by a frequency shift key transmission technique. At the surface, a frequency shift key demodulation unit transmits the decoupled data to an asynchronous receiver interfaced to the electronic digital signal processor. During a recording phase, the signals from the logging tool are read by the electronic digital signal processor and stored for later processing. During a calculating phase, the stored data is processed by the digital signal processor and the results are outputted to a printer or plotter, or both

Advancing the use of noncoding RNA in regulatory toxicology: Report of an ECETOC workshop.

Science.gov (United States)

Aigner, Achim; Buesen, Roland; Gant, Tim; Gooderham, Nigel; Greim, Helmut; Hackermüller, Jörg; Hubesch, Bruno; Laffont, Madeleine; Marczylo, Emma; Meister, Gunter; Petrick, Jay S; Rasoulpour, Reza J; Sauer, Ursula G; Schmidt, Kerstin; Seitz, Hervé; Slack, Frank; Sukata, Tokuo; van der Vies, Saskia M; Verhaert, Jan; Witwer, Kenneth W; Poole, Alan

2016-12-01

The European Centre for the Ecotoxicology and Toxicology of Chemicals (ECETOC) organised a workshop to discuss the state-of-the-art research on noncoding RNAs (ncRNAs) as biomarkers in regulatory toxicology and as analytical and therapeutic agents. There was agreement that ncRNA expression profiling data requires careful evaluation to determine the utility of specific ncRNAs as biomarkers. To advance the use of ncRNA in regulatory toxicology, the following research priorities were identified: (1) Conduct comprehensive literature reviews to identify possibly suitable ncRNAs and areas of toxicology where ncRNA expression profiling could address prevailing scientific deficiencies. (2) Develop consensus on how to conduct ncRNA expression profiling in a toxicological context. (3) Conduct experimental projects, including, e.g., rat (90-day) oral toxicity studies, to evaluate the toxicological relevance of the expression profiles of selected ncRNAs. Thereby, physiological ncRNA expression profiles should be established, including the biological variability of healthy individuals. To substantiate the relevance of key ncRNAs for cell homeostasis or pathogenesis, molecular events should be dose-dependently linked with substance-induced apical effects. Applying a holistic approach, knowledge on ncRNAs, 'omics and epigenetics technologies should be integrated into adverse outcome pathways to improve the understanding of the functional roles of ncRNAs within a regulatory context. Crown Copyright © 2016. Published by Elsevier Inc. All rights reserved.

77 FR 12313 - Food Labeling Workshop; Public Workshop

Science.gov (United States)

2012-02-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-N-0001] Food Labeling Workshop; Public Workshop AGENCY: Food and Drug Administration, HHS. ACTION: Notice of... District Office (DALDO), in collaboration with Oklahoma State University (OSU), Robert M. Kerr Food...

75 FR 29775 - Food Labeling Workshop; Public Workshop

Science.gov (United States)

2010-05-27

... DEPARTMENT OF HEALTH AND HUMAN SERVICES [Docket No. FDA-2010-N-0001] Food and Drug Administration Food Labeling Workshop; Public Workshop AGENCY: Food and Drug Administration, HHS. ACTION: Notice of...: Institute of Food Science & Engineering, University of Arkansas, 2650 North Young Ave., Fayetteville, AR...

Systems Engineering Workshops | Wind | NREL

Science.gov (United States)

Workshops Systems Engineering Workshops The Wind Energy Systems Engineering Workshop is a biennial topics relevant to systems engineering and the wind industry. The presentations and agendas are available for all of the Systems Engineering Workshops: The 1st NREL Wind Energy Systems Engineering Workshop

Proceedings 11th International Workshop on Automated Specification and Verification of Web Systems

DEFF Research Database (Denmark)

2015-01-01

is a yearly interdisciplinary forum for researchers originating from the following areas: declarative, rule-based programming, formal methods, software engineering and web-based systems. The workshop fosters the cross-fertilisation and advancement of hybrid methods from such areas....

Egyptian Journal of Medical Laboratory Sciences: Advanced Search

African Journals Online (AJOL)

Egyptian Journal of Medical Laboratory Sciences: Advanced Search. Journal Home > Egyptian Journal of Medical Laboratory Sciences: Advanced Search. Log in or Register to get access to full text downloads.

Proceedings of the 2004 NASA/ONR Circulation Control Workshop, Part 2

Science.gov (United States)

Jones, Gregory S. (Editor); Joslin, Ronald D. (Editor)

2005-01-01

This conference proceeding is comprised of papers that were presented at the NASA/ONR Circulation Control Workshop held 16-17 March 2004 at the Radisson-Hampton in Hampton, VA. Over two full days, 30 papers and 4 posters were presented with 110 scientists and engineers in attendance, representing 3 countries. As technological advances influence the efficiency and effectiveness of aerodynamic and hydrodynamic applications, designs, and operations, this workshop was intended to address the technologies, systems, challenges and successes specific to Coanda driven circulation control in aerodynamics and hydrodynamics. A major goal of this workshop was to determine the state-of-the-art in circulation control and to assess the future directions and applications for circulation control. The 2004 workshop addressed applications, experiments, computations, and theories related to circulation control, emphasizing fundamental physics, systems analysis, and applied research. The workshop consisted of single session oral presentations, posters, and written papers that are documented in this unclassified conference proceeding. The format of this written proceeding follows the agenda of the workshop. Each paper is followed with the presentation given at the workshop. the editors compiled brief summaries for each effort that is at the end of this proceeding. These summaries include the paper, oral presentation, and questions or comments that occurred during the workshop. The 2004 Circulation Control Workshop focused on applications including Naval vehicles (Surface and Underwater vehicles), Fixed Wing Aviation (general aviation, commercial, cargo, and business aircraft); V/STOL platforms (helicopters, military aircraft, tilt rotors); propulsion systems (propellers, jet engines, gas turbines), and ground vehicles (automotive, trucks, and other); wind turbines, and other nontraditional applications (e.g., vacuum cleaner, ceiling fan). As part of the CFD focus area of the 2004 CC

Summary from the epistemic uncertainty workshop: consensus amid diversity

International Nuclear Information System (INIS)

Ferson, Scott; Joslyn, Cliff A.; Helton, Jon C.; Oberkampf, William L.; Sentz, Kari

2004-01-01

The 'Epistemic Uncertainty Workshop' sponsored by Sandia National Laboratories was held in Albuquerque, New Mexico, on 6-7 August 2002. The workshop was organized around a set of Challenge Problems involving both epistemic and aleatory uncertainty that the workshop participants were invited to solve and discuss. This concluding article in a special issue of Reliability Engineering and System Safety based on the workshop discusses the intent of the Challenge Problems, summarizes some discussions from the workshop, and provides a technical comparison among the papers in this special issue. The Challenge Problems were computationally simple models that were intended as vehicles for the illustration and comparison of conceptual and numerical techniques for use in analyses that involve: (i) epistemic uncertainty, (ii) aggregation of multiple characterizations of epistemic uncertainty, (iii) combination of epistemic and aleatory uncertainty, and (iv) models with repeated parameters. There was considerable diversity of opinion at the workshop about both methods and fundamental issues, and yet substantial consensus about what the answers to the problems were, and even about how each of the four issues should be addressed. Among the technical approaches advanced were probability theory, Dempster-Shafer evidence theory, random sets, sets of probability measures, imprecise coherent probabilities, coherent lower previsions, probability boxes, possibility theory, fuzzy sets, joint distribution tableaux, polynomial chaos expansions, and info-gap models. Although some participants maintained that a purely probabilistic approach is fully capable of accounting for all forms of uncertainty, most agreed that the treatment of epistemic uncertainty introduces important considerations and that the issues underlying the Challenge Problems are legitimate and significant. Topics identified as meriting additional research include elicitation of uncertainty representations, aggregation of

Applied antineutrino physics workshop

International Nuclear Information System (INIS)

Lund, James C.

2008-01-01

This workshop is the fourth one of a series that includes the Neutrino Geophysics Conference at Honolulu, Hawaii, which I attended in 2005. This workshop was organized by the Astro-Particle and Cosmology laboratory in the recently opened Condoret building of the University of Paris. More information, including copies of the presentations, on the workshop is available on the website: www.apc.univ-paris7.fr/AAP2007/. The workshop aims at opening neutrino physics to various fields such that it can be applied in geosciences, nuclear industry (reactor and spent fuel monitoring) and non-proliferation. The workshop was attended by over 60 people from Europe, USA, Asia and Brazil. The meeting was also attended by representatives of the Comprehensive nuclear-Test Ban Treaty (CTBT) and the International Atomic Energy Agency (IAEA). The workshop also included a workshop dinner on board of a river boat sailing the Seine river

Adobe Photoshop CS5 for Photographers The Ultimate Workshop

CERN Document Server

Evening, Martin

2010-01-01

If you already have a good knowledge of Adobe Photoshop and are looking to advance your skills, Adobe Photoshop CS5 for Photographers: The Ultimate Workshop is the book you've been waiting for.  Renowned photographers Martin Evening and Jeff Schewe impart their Photoshop tips and workflow, showing you how to use a vast array of rarely seen advanced Photoshop techniques.  Whether the subject is serious retouching work, weird and wonderful compositions, or planning a shoot before you've even picked up a camera, you can be sure that the advice is based on years of practical experience.

Estimation of the non records logs from existing logs using artificial neural networks

Directory of Open Access Journals (Sweden)

Mehdi Mohammad Salehi

2017-12-01

Full Text Available Finding the information of the hydrocarbon reservoirs from well logs is one of the main objectives of the engineers. But, missing the log records (due to many reasons such as broken instruments, unsuitable borehole and etc. is a major challenge to achieve it. Prediction of the density and resistivity logs (Rt, DT and LLS from the conventional wire-line logs in one of the Iranian southwest oil fields is the main purpose of this study. Multilayer neural network was applied to develop an intelligent predictive model for prediction of the logs. A total of 3000 data sets from 3 wells (A, B and C of the studied field were used. Among them, the data of A, B and C wells were used to constructing and testing the model, respectively. To evaluate the performance of the model, the mean square error (MSE and correlation coefficient (R2 in the test data were calculated. A comparison between the MSE of the proposed model and recently intelligent models shows that the proposed model is more accurate than others. Acceptable accuracy and using conventional well logging data are the highlight advantages of the proposed intelligent model.

XIII International Workshop on Hadron Physics

CERN Document Server

2015-01-01

The XIII International Workshop on Hadron Physics, XIII Hadron Physics, is intended for graduate students, postdocs and researchers in Hadronic Physics, High Energy Physics, Astrophysics and Effective Field Theories, who wish to improve their theoretical background, learn about recent experimental results and develop collaboration projects. The series Hadron Physics, in activity since 1988, has the format of an advanced school and has the objective to introduce, in a series of pedagogical lectures, new lines of research in Strong Interaction Physics, mainly concerned with QCD. It envisages also to stimulate collaborations in international level.

Peer-Review Writing Workshops in College Courses: Students’ Perspectives about Online and Classroom Based Workshops

Directory of Open Access Journals (Sweden)

Erin B. Jensen

2016-11-01

Full Text Available Peer-review workshops are commonly used in writing courses as a way for students to give their peers feedback as well as help their own writing. Most of the research on peer-review workshops focuses on workshops held in traditional in-person courses, with less research on peer-review workshops held online. Students in a freshman writing course experienced both a classroom based writing workshop and an online workshop and then took a survey about their experiences. The majority of the students preferred the online writing workshop because of the convenience of the workshop and being able to post anonymous reviews. Students whom preferred the traditional in-person writing workshop liked being able to talk with their peers about their papers. This research article focuses on the students’ responses and experiences with traditional and online peer-reviews.

Applying Big Data solutions for log analytics in the PanDA infrastructure

CERN Document Server

Alekseev, Aleksandr; The ATLAS collaboration

2017-01-01

PanDA is the workflow management system of the ATLAS experiment at the LHC and is responsible for generating, brokering and monitoring up to two million jobs per day across 150 computing centers in the Worldwide LHC Computing Grid. The PanDA core consists of several components deployed centrally on around 20 servers. The daily log volume is around 400GB per day. In certain cases, troubleshooting a particular issue on the raw log files can be compared to searching for a needle in a haystack and requires a high level of expertise. Therefore we decided to build on trending Big Data solutions and utilize the ELK infrastructure (Filebeat, Logstash, Elastic Search and Kibana) to process, index and analyze our log files. This allows to overcome troubleshooting complexity, provides a better interface to the operations team and generates advanced analytics to understand our system. This paper will describe the features of the ELK stack, our infrastructure, optimal configuration settings and filters. We will provide ex...

ICP-MS Workshop

Energy Technology Data Exchange (ETDEWEB)

Carman, April J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Eiden, Gregory C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-11-01

This is a short document that explains the materials that will be transmitted to LLNL and DNN HQ regarding the ICP-MS Workshop held at PNNL June 17-19th. The goal of the information is to pass on to LLNL information regarding the planning and preparations for the Workshop at PNNL in preparation of the SIMS workshop at LLNL.

Temporal Decay in Timber Species Composition and Value in Amazonian Logging Concessions.

Science.gov (United States)

Richardson, Vanessa A; Peres, Carlos A

2016-01-01

Throughout human history, slow-renewal biological resource populations have been predictably overexploited, often to the point of economic extinction. We assess whether and how this has occurred with timber resources in the Brazilian Amazon. The asynchronous advance of industrial-scale logging frontiers has left regional-scale forest landscapes with varying histories of logging. Initial harvests in unlogged forests can be highly selective, targeting slow-growing, high-grade, shade-tolerant hardwood species, while later harvests tend to focus on fast-growing, light-wooded, long-lived pioneer trees. Brazil accounts for 85% of all native neotropical forest roundlog production, and the State of Pará for almost half of all timber production in Brazilian Amazonia, the largest old-growth tropical timber reserve controlled by any country. Yet the degree to which timber harvests beyond the first-cut can be financially profitable or demographically sustainable remains poorly understood. Here, we use data on legally planned logging of ~17.3 million cubic meters of timber across 314 species extracted from 824 authorized harvest areas in private and community-owned forests, 446 of which reported volumetric composition data by timber species. We document patterns of timber extraction by volume, species composition, and monetary value along aging eastern Amazonian logging frontiers, which are then explained on the basis of historical and environmental variables. Generalized linear models indicate that relatively recent logging operations farthest from heavy-traffic roads are the most selective, concentrating gross revenues on few high-value species. We find no evidence that the post-logging timber species composition and total value of forest stands recovers beyond the first-cut, suggesting that the commercially most valuable timber species become predictably rare or economically extinct in old logging frontiers. In avoiding even more destructive land-use patterns, managing

14th Workshop on Crystalline Silicon Solar Cells& Modules: Materials and Processes; Extended Abstracts and Papers

Energy Technology Data Exchange (ETDEWEB)

Sopori, B. L.

2004-08-01

The 14th Workshop will provide a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. It will offer an excellent opportunity for researchers in private industry and at universities to prioritize mutual needs for future collaborative research. The workshop is intended to address the fundamental properties of PV silicon, new solar cell designs, advanced solar cell processing techniques, and cell-related module issues. A combination of oral presentations by invited speakers, poster sessions, and discussion sessions will review recent advances in crystal growth, new cell designs, new processes and process characterization techniques, cell fabrication approaches suitable for future manufacturing demands, and solar cell encapsulation. This year's theme, ''Crystalline Si Solar Cells: Leapfrogging the Barriers,'' reflects the continued success of crystalline Si PV in overcoming technological barriers to improve solar cell performance and lower the cost of Si PV. The workshop will consist of presentations by invited speakers, followed by discussion sessions. In addition, there will be two poster sessions presenting the latest research and development results. Some presentations will address recent technologies in the microelectronics field that may have a direct bearing on PV. The sessions will include: Advances in crystal growth and material issues; Impurities and defects; Dynamics during device processing; Passivation; High-efficiency Si solar cells; Advanced processing; Thin Si solar cells; and Solar cell reliability and module issues.

78 FR 33849 - Battery-Powered Medical Devices Workshop: Challenges and Opportunities; Public Workshop; Request...

Science.gov (United States)

2013-06-05

... after the public workshop on the Internet at http://www.fda.gov/MedicalDevices/NewsEvents/Workshops..., compact, and mobile, the number of battery-powered medical devices will continue to increase. While many...] Battery-Powered Medical Devices Workshop: Challenges and Opportunities; Public Workshop; Request for...

Reactor simulator development. Workshop material

International Nuclear Information System (INIS)

2001-01-01

The International Atomic Energy Agency (IAEA) has established a programme in nuclear reactor simulation computer programs to assist its Member States in education and training. The objective is to provide, for a variety of advanced reactor types, insight and practice in reactor operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the supply or development of simulation programs and training material, sponsors training courses and workshops, and distributes documentation and computer programs. This publication consists of course material for workshops on development of such reactor simulators. Participants in the workshops are provided with instruction and practice in the development of reactor simulation computer codes using a model development system that assembles integrated codes from a selection of pre-programmed and tested sub-components. This provides insight and understanding into the construction and assumptions of the codes that model the design and operational characteristics of various power reactor systems. The main objective is to demonstrate simple nuclear reactor dynamics with hands-on simulation experience. Using one of the modular development systems, CASSIM tm , a simple point kinetic reactor model is developed, followed by a model that simulates the Xenon/Iodine concentration on changes in reactor power. Lastly, an absorber and adjuster control rod, and a liquid zone model are developed to control reactivity. The built model is used to demonstrate reactor behavior in sub-critical, critical and supercritical states, and to observe the impact of malfunctions of various reactivity control mechanisms on reactor dynamics. Using a PHWR simulator, participants practice typical procedures for a reactor startup and approach to criticality. This workshop material consists of an introduction to systems used for developing reactor simulators, an overview of the dynamic simulation

Workshop on Advanced Technologies and Future Joint Warfighting, April 8-10, 1999, Summary of Proceedings

National Research Council Canada - National Science Library

Hurley, William

1999-01-01

.... The workshop brought together young academic scientists and engineers who are members or alumni of the Defense Science Study Group and active duty military officers and civilians who are working...

ALICES: an advanced object-oriented software workshop for simulators

International Nuclear Information System (INIS)

Sayet, R.L.; Rouault, G.; Pieroux, D.; Houte, U. Van

1999-01-01

Reducing simulator development costs while improving model quality, user-friendliness and teaching capabilities, is a major target for many years in the simulation industry. It has led to the development of specific software tools which have been improved progressively following the new features and capabilities offered by the software industry. Unlike most of these software tools, ALICES (which is a French acronym for 'Interactive Software Workshop for the Design of Simulators') is not an upgrade of a previous generation of tools, like putting a graphical front-end to a classical code generator, but a really new development. Its design specification is based on previous experience with different tools as well as on new capabilities of software technology, mainly in Object Oriented Design. This allowed us to make a real technological 'jump' in the simulation industry, beyond the constraints of some traditional approaches. The main objectives behind the development of ALICES were the following: (1) Minimizing the simulator development time and costs: a simulator development consists mainly in developing software. One way to reduce costs is to facilitate reuse of existing software by developing standard components, and by defining interface standards, (2) Insuring that the produced simulator can be maintained and updated at a minimal cost: a simulator must evolve along with the simulated process, and it is then necessary to update periodically the simulator. The cost of an adequate maintenance is highly dependent of the quality of the software workshop, (3) Covering the whole simulator development process: from the data package to the acceptance tests and for maintenance and upgrade activities; with the whole development team, even if it is dispatched at different working sites; respecting the Quality Assurance rules and procedures (CORYS T.E.S.S. and TRACTEBEL are ISO-9001 certified). The development of ALICES was also done to comply with the following two main

Workshop Proceedings

DEFF Research Database (Denmark)

2012-01-01

, the main focus there is on spoken languages in their written and spoken forms. This series of workshops, however, offers a forum for researchers focussing on sign languages. For the third time, the workshop had sign language corpora as its main topic. This time, the focus was on the interaction between...... corpus and lexicon. More than half of the papers presented contribute to this topic. Once again, the papers at this workshop clearly identify the potentials of even closer cooperation between sign linguists and sign language engineers, and we think it is events like this that contribute a lot to a better...

Geophysical well logging operations and log analysis in Geothermal Well Desert Peak No. B-23-1

Energy Technology Data Exchange (ETDEWEB)

Sethi, D.K.; Fertl, W.H.

1980-03-01

Geothermal Well Desert Peak No. B-23-1 was logged by Dresser Atlas during April/May 1979 to a total depth of 2939 m (9642 ft). A temperature of 209/sup 0/C (408/sup 0/F) was observed on the maximum thermometer run with one of the logging tools. Borehole tools rated to a maximum temperature of 204.4/sup 0/C (400/sup 0/F) were utilized for logging except for the Densilog tool, which was from the other set of borehole instruments, rated to a still higher temperature, i.e., 260/sup 0/C (500/sup 0/F). The quality of the logs recorded and the environmental effects on the log response have been considered. The log response in the unusual lithologies of igneous and metamorphic formations encountered in this well could be correlated with the drill cutting data. An empirical, statistical log interpretation approach has made it possible to obtain meaningful information on the rocks penetrated. Various crossplots/histograms of the corrected log data have been generated on the computer. These are found to provide good resolution between the lithological units in the rock sequence. The crossplotting techniques and the statistical approach were combined with the drill cutting descriptions in order to arrive at the lithological characteristics. The results of log analysis and recommendations for logging of future wells have been included.

Theoretical and Numerical Study of Seismoelectric Logs for Logging While Drilling (LWD

Directory of Open Access Journals (Sweden)

Sun Xiang-Yang

2017-01-01

Full Text Available When the acoustic field propagates in the porous medium, the electromagnetic wave can be induced by the seismoelectric effects which can be used in the logging. This paper studies the seismoelectric wave field and deduces the formulations of the acoustic and electromagnetic field of the liquid in the well, and gives the acoustic and electromagnetic boundary conditions between the driller collar and the log liquid, when the driller collar is added. We also do the numerical simulation of the seismoelectric wave field excited by monopole source, study the velocity dispersion characteristics of the acoustic and electromagnetic field, and investigate the detective depth of the seismoelectric logs. Through the simulation we know the seismoelectric logs can avoid the interference of drill collar wave. This paper also provides theoretical guidance for the design of receiving antenna.

Face logging in Copenhagen Limestone, Denmark

DEFF Research Database (Denmark)

Jakobsen, Lisa; Foged, Niels Nielsen; Erichsen, Lars

2015-01-01

tunnel in Copenhagen more than 2.5 km face logs were made in 467 locations at underground stations, shafts, caverns and along bored tunnels. Over 160 geotechnical boreholes, many with geophysical logging were executed prior to construction works. The bedrock consists of Paleogene "Copenhagen limestone......The requirement for excavation support can be assessed from face logging. Face logs can also improve our knowledge of lithological and structural conditions within bedrock and supplement information from boreholes and geophysical logs. During the construction of 8 km metro tunnel and 4 km heating....... The induration degrees recorded in face logs and boreholes are compared and correlated. Distinct geophysical log markers are used to divide the limestone into three units. These marker horizons are correlated between face logs and geotechnical boreholes. A 3D model of the strength variations recorded within...

Proceedings of the 2nd ACM SIGSPATIAL International Workshop on Indoor Spatial Awareness

DEFF Research Database (Denmark)

These proceedings contain the papers selected for presentation at the Second International Workshop on Indoor Spatial Awareness, hosted by ACM SIGSPATIAL and held in conjunction with the18th ACM SIGSPATIAL International Conference on Advances in Geographic Information Systems (ACM SIGSPATIAL GIS...

Fiscal 1998 engineer interexchange project (coal mine technology field). International interexchange project (Workshop in Japan); 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya). Kokusai koryu jigyo (kokunai workshop)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the workshop and technical tour held in Japan for technical interexchange of domestic and overseas engineers. From the information obtained, the higher productivity of coal mines is dependent on selective mining under blessed geological conditions, however, basically establishment of an advanced management technique for inexpensive stable operation. Both preliminary collection of geological information and introduction of advanced facilities even under unstable conditions are necessary. The balance and optimization of the whole system, and an excellent human nature for operation are also essential. Use of roof bolt supports is diffusing as improvement technology of excavation speed and roof control technology over the world. However, for introduction of new technologies, collection of test results and various kinds of training are necessary. Methane gas in coal seams as the main theme of the Hokkaido workshop is a precious unused natural resource, and important for prevention of global warming and coal mine protection measures. Its use is dependent on development of gas drainage technology. (NEDO)

Report from the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies

International Nuclear Information System (INIS)

Hallbert, Bruce P.; Persensky, J.J.; Smidts, Carol; Aldemir, Tunc; Naser, Joseph

2009-01-01

electricity generation. As an initial step in accomplishing this effort, the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies was held March 20-21, 2009, in Columbus, Ohio, to enable industry stakeholders and researchers in identification of the nuclear industry's needs in the areas of future I and C technologies and corresponding technology gaps and research capabilities. Approaches for collaboration to bridge or fill the technology gaps were presented and R and D activities and priorities recommended. This report documents the presentations and discussions of the workshop and is intended to serve as a basis for the plan under development to achieve the goals of the I and C research pathway.

Report from the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies

Energy Technology Data Exchange (ETDEWEB)

Bruce P. Hallbert; J. J. Persensky; Carol Smidts; Tunc Aldemir; Joseph Naser

2009-08-01

. As an initial step in accomplishing this effort, the Light Water Reactor Sustainability Workshop on Advanced Instrumentation, Information, and Control Systems and Human-System Interface Technologies was held March 20–21, 2009, in Columbus, Ohio, to enable industry stakeholders and researchers in identification of the nuclear industry’s needs in the areas of future I&C technologies and corresponding technology gaps and research capabilities. Approaches for collaboration to bridge or fill the technology gaps were presented and R&D activities and priorities recommended. This report documents the presentations and discussions of the workshop and is intended to serve as a basis for the plan under development to achieve the goals of the I&C research pathway.

Workshop report

African Journals Online (AJOL)

abp

2017-09-14

Sep 14, 2017 ... health: report of first EQUIST training workshop in Nigeria .... The difference between the before and after measurements was ... After the administration of the pre-workshop questionnaire the ... represent Likert rating scale of 1-5 points, where 1point = grossly .... Procedures Manual for the "Evaluating.

Proceedings of the 5th US/German Workshop on Salt Repository Research Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leigh, Christi [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Von Berlepsche, Thilo [DBE Technology, Peine (Germany)

2015-01-01

The 5th US/German Workshop on Salt Repository Research, Design, and Operation was held in Santa Fe New Mexico September 8-10, 2014. The forty seven registered participants were equally divided between the United States (US) and Germany, with one participant from The Netherlands. The agenda for the 2014 workshop was under development immediately upon finishing the 4th Workshop. Ongoing, fundamental topics such as thermomechanical behavior of salt, plugging and sealing, the safety case, and performance assessment continue to advance the basis for disposal of heat-generating nuclear waste in salt formations. The utility of a salt underground research laboratory (URL) remains an intriguing concept engendering discussion of testing protocol. By far the most interest in this years’ workshop pertained to operational safety. Given events at the Waste Isolation Pilot Plant (WIPP), this discussion took on a new sense of relevance and urgency.

Monte Carlo - Advances and Challenges

International Nuclear Information System (INIS)

Brown, Forrest B.; Mosteller, Russell D.; Martin, William R.

2008-01-01

Abstract only, full text follows: With ever-faster computers and mature Monte Carlo production codes, there has been tremendous growth in the application of Monte Carlo methods to the analysis of reactor physics and reactor systems. In the past, Monte Carlo methods were used primarily for calculating k eff of a critical system. More recently, Monte Carlo methods have been increasingly used for determining reactor power distributions and many design parameters, such as β eff , l eff , τ, reactivity coefficients, Doppler defect, dominance ratio, etc. These advanced applications of Monte Carlo methods are now becoming common, not just feasible, but bring new challenges to both developers and users: Convergence of 3D power distributions must be assured; confidence interval bias must be eliminated; iterated fission probabilities are required, rather than single-generation probabilities; temperature effects including Doppler and feedback must be represented; isotopic depletion and fission product buildup must be modeled. This workshop focuses on recent advances in Monte Carlo methods and their application to reactor physics problems, and on the resulting challenges faced by code developers and users. The workshop is partly tutorial, partly a review of the current state-of-the-art, and partly a discussion of future work that is needed. It should benefit both novice and expert Monte Carlo developers and users. In each of the topic areas, we provide an overview of needs, perspective on past and current methods, a review of recent work, and discussion of further research and capabilities that are required. Electronic copies of all workshop presentations and material will be available. The workshop is structured as 2 morning and 2 afternoon segments: - Criticality Calculations I - convergence diagnostics, acceleration methods, confidence intervals, and the iterated fission probability, - Criticality Calculations II - reactor kinetics parameters, dominance ratio, temperature

Eighteenth Workshop on Recent Developments in Computer Simulation Studies in Condensed Matter Physics

CERN Document Server

Landau, David P; Schüttler, Heinz-Bernd; Computer Simulation Studies in Condensed-Matter Physics XVIII

2006-01-01

This volume represents a "status report" emanating from presentations made during the 18th Annual Workshop on Computer Simulations Studies in Condensed Matter Physics at the Center for Simulational Physics at the University of Georgia in March 2005. It provides a broad overview of the most recent advances in the field, spanning the range from statistical physics to soft condensed matter and biological systems. Results on nanostructures and materials are included as are several descriptions of advances in quantum simulations and quantum computing as well as.methodological advances.

Proceedings: Regenerative Medicine for Lung Diseases: A CIRM Workshop Report.

Science.gov (United States)

Kadyk, Lisa C; DeWitt, Natalie D; Gomperts, Brigitte

2017-10-01

The mission of the California Institute of Regenerative Medicine (CIRM) is to accelerate treatments to patients with unmet medical needs. In September 2016, CIRM sponsored a workshop held at the University of California, Los Angeles, to discuss regenerative medicine approaches for treatment of lung diseases and to identify the challenges remaining for advancing such treatments to the clinic and market approval. Workshop participants discussed current preclinical and clinical approaches to regenerative medicine in the lung, as well as the biology of lung stem cells and the role of stem cells in the etiology of various lung diseases. The outcome of this effort was the recognition that whereas transient cell delivery approaches are leading the way in the clinic, recent advances in the understanding of lung stem cell biology, in vitro and in vivo disease modeling, gene editing and replacement methods, and cell engraftment approaches raise the prospect of developing cures for some lung diseases in the foreseeable future. In addition, advances in in vitro modeling using lung organoids and "lung on a chip" technology are setting the stage for high quality small molecule drug screening to develop treatments for lung diseases with complex biology. Stem Cells Translational Medicine 2017;6:1823-1828. © 2017 The Authors Stem Cells Translational Medicine published by Wiley Periodicals, Inc. on behalf of AlphaMed Press.

Proceedings of the workshop on π, K, η-nucleon interactions

International Nuclear Information System (INIS)

1992-04-01

This workshop was held at the Research Center for Nuclear Physics, Osaka University, from February 18 to 20, 1991. This is the first attempt on this theme. The understanding of atomic nuclei as nucleon many body system is inseparable from the deeper understanding on the structures of nucleons and mesons and their interaction. It is considered that the physical experiment on medium energy atomic nuclei which is positively advanced at present in various places aims at the understanding of the hadron many body system of nucleons and mesons through the phenomena to which various degrees of freedom are related. This workshop is going to study on such hadron physics of atomic nuclei centering around the research including the elementary processes of various problems in the interactions of π and nuclei, K and nuclei and η and nuclei, taking the problems of the internal structures of hadrons themselves into the field of view. More than 50 people took part in the workshop, and also the reports from experiment side were carried out. In this book, 22 papers are collected. (K.I.)

Quantum Testbeds Stakeholder Workshop (QTSW) Report meeting purpose and agenda.

Energy Technology Data Exchange (ETDEWEB)

Hebner, Gregory A.

2017-04-01

Quantum computing (QC) is a promising early-stage technology with the potential to provide scientific computing capabilities far beyond what is possible with even an Exascale computer in specific problems of relevance to the Office of Science. These include (but are not limited to) materials modeling, molecular dynamics, and quantum chromodynamics. However, commercial QC systems are not yet available and the technical maturity of current QC hardware, software, algorithms, and systems integration is woefully incomplete. Thus, there is a significant opportunity for DOE to define the technology building blocks, and solve the system integration issues to enable a revolutionary tool. Once realized, QC will have world changing impact on economic competitiveness, the scientific enterprise, and citizen well-being. Prior to this workshop, DOE / Office of Advanced Scientific Computing Research (ASCR) hosted a workshop in 2015 to explore QC scientific applications. The goal of that workshop was to assess the viability of QC technologies to meet the computational requirements in support of DOE’s science and energy mission and to identify the potential impact of these technologies.

Climate Research Roadmap Workshop: Summary Report, May 13-14, 2010

Energy Technology Data Exchange (ETDEWEB)

None

2010-09-01

In recognition of the ongoing advances and challenges of climate change research, DOE's Office of Biological and Environmental Research (BER) organized a workshop asking the scientific community to identify the current state of climate science. The goal of the workshop was to determine the research challenges important for developing a predictive understanding of global climate. Participants were asked to focus on interdisciplinary research that capitalized on BER's scientific strengths in Atmospheric System Research, Terrestrial Ecosystem Science, and Climate and Earth System Modeling. Approximately 50 scientists representing these three areas were asked to identify desired outcomes for the next 10 years. Goals were identified for the near (1--3 years), mid (4--7 years), and long term (8--10 years). Discussions were focused by discipline (atmospheric, terrestrial, and modeling) and by latitude (high, temperate, and tropical). In addition, opportunities and needs for integration across disciplines and latitudes were identified with a specific focus on crosscutting challenges and outcomes. BER will use this workshop output to update its strategic plan for climate research.

Summary of workshop on materials issues in low emission boilers and high efficiency coal-fired cycles

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The purpose of the workshop was to review with experts in the field the materials issues associated with two of the primary coal power systems being developed by the DOE Office of Fossil Energy. The DOE-FE Advanced Power Systems Program includes natural gas-based and coal-based power systems. Major activities in the natural gas-based power systems area include the Advanced Turbine Systems (ATS) Program, the Fuel Cells Program, and Hybrid Cycles. The coal-based power systems projects include the Low Emissions Boiler Systems (LEBS) Program, the High-Performance Power Systems Program (HIPPS), the Integrated (Coal) Gasification Combined-Cycle Program, and the Fluidized-Bed Combustion Program. This workshop focused on the materials issues associated with the LEBS and HIPPS technologies.

Advances in Cross-Cutting Ideas for Computational Climate Science

Energy Technology Data Exchange (ETDEWEB)

Ng, Esmond [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Evans, Katherine J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Caldwell, Peter [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hoffman, Forrest M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jackson, Charles [Univ. of Texas, Austin, TX (United States); Kerstin, Van Dam [Brookhaven National Lab. (BNL), Upton, NY (United States); Leung, Ruby [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Martin, Daniel F. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ostrouchov, George [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Tuminaro, Raymond [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ullrich, Paul [Univ. of California, Davis, CA (United States); Wild, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Williams, Samuel [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2017-01-01

This report presents results from the DOE-sponsored workshop titled, ``Advancing X-Cutting Ideas for Computational Climate Science Workshop,'' known as AXICCS, held on September 12--13, 2016 in Rockville, MD. The workshop brought together experts in climate science, computational climate science, computer science, and mathematics to discuss interesting but unsolved science questions regarding climate modeling and simulation, promoted collaboration among the diverse scientists in attendance, and brainstormed about possible tools and capabilities that could be developed to help address them. Emerged from discussions at the workshop were several research opportunities that the group felt could advance climate science significantly. These include (1) process-resolving models to provide insight into important processes and features of interest and inform the development of advanced physical parameterizations, (2) a community effort to develop and provide integrated model credibility, (3) including, organizing, and managing increasingly connected model components that increase model fidelity yet complexity, and (4) treating Earth system models as one interconnected organism without numerical or data based boundaries that limit interactions. The group also identified several cross-cutting advances in mathematics, computer science, and computational science that would be needed to enable one or more of these big ideas. It is critical to address the need for organized, verified, and optimized software, which enables the models to grow and continue to provide solutions in which the community can have confidence. Effectively utilizing the newest computer hardware enables simulation efficiency and the ability to handle output from increasingly complex and detailed models. This will be accomplished through hierarchical multiscale algorithms in tandem with new strategies for data handling, analysis, and storage. These big ideas and cross-cutting technologies for

Advances in Cross-Cutting Ideas for Computational Climate Science

Energy Technology Data Exchange (ETDEWEB)

Ng, E.; Evans, K.; Caldwell, P.; Hoffman, F.; Jackson, C.; Van Dam, K.; Leung, R.; Martin, D.; Ostrouchov, G.; Tuminaro, R.; Ullrich, P.; Wild, S.; Williams, S.

2017-01-01

This report presents results from the DOE-sponsored workshop titled, Advancing X-Cutting Ideas for Computational Climate Science Workshop,'' known as AXICCS, held on September 12--13, 2016 in Rockville, MD. The workshop brought together experts in climate science, computational climate science, computer science, and mathematics to discuss interesting but unsolved science questions regarding climate modeling and simulation, promoted collaboration among the diverse scientists in attendance, and brainstormed about possible tools and capabilities that could be developed to help address them. Emerged from discussions at the workshop were several research opportunities that the group felt could advance climate science significantly. These include (1) process-resolving models to provide insight into important processes and features of interest and inform the development of advanced physical parameterizations, (2) a community effort to develop and provide integrated model credibility, (3) including, organizing, and managing increasingly connected model components that increase model fidelity yet complexity, and (4) treating Earth system models as one interconnected organism without numerical or data based boundaries that limit interactions. The group also identified several cross-cutting advances in mathematics, computer science, and computational science that would be needed to enable one or more of these big ideas. It is critical to address the need for organized, verified, and optimized software, which enables the models to grow and continue to provide solutions in which the community can have confidence. Effectively utilizing the newest computer hardware enables simulation efficiency and the ability to handle output from increasingly complex and detailed models. This will be accomplished through hierarchical multiscale algorithms in tandem with new strategies for data handling, analysis, and storage. These big ideas and cross-cutting technologies for enabling

'Good Vibrations': A workshop on oscillations and normal modes

International Nuclear Information System (INIS)

Barbieri, Sara R.; Carpineti, Marina; Giliberti, Marco; Stellato, Marco; Rigon, Enrico; Tamborini, Marina

2015-01-01

We describe some theatrical strategies adopted in a two hour workshop in order to show some meaningful experiments and the underlying useful ideas to describe a secondary school path on oscillations, that develops from harmonic motion to normal modes of oscillations, and makes extensive use of video analysis, data logging, slow motions and applet simulations. Theatre is an extremely useful tool to stimulate motivation starting from positive emotions. That is the reason why the theatrical approach to the presentation of physical themes has been explored by the group 'Lo spettacolo della Fisica' (http://spettacolo.fisica.unimi.it) of the Physics Department of University of Milano for the last ten years (Carpineti et al., JCOM, 10 (2011) 1; Nuovo Cimento B, 121 (2006) 901) and has been inserted also in the European FP7 Project TEMI (Teaching Enquiry with Mysteries Incorporated, see http://teachingmysteries.eu/en) which involves 13 different partners coming from 11 European countries, among which the Italian (Milan) group. According to the TEMI guidelines, this workshop has a written script based on emotionally engaging activities of presenting mysteries to be solved while participants have been involved in nice experiments following the developed path.

Workshops as a Research Methodology

DEFF Research Database (Denmark)

Ørngreen, Rikke; Levinsen, Karin Tweddell

2017-01-01

, and workshops as a research methodology. Focusing primarily on the latter, this paper presents five studies on upper secondary and higher education teachers’ professional development and on teaching and learning through video conferencing. Through analysis and discussion of these studies’ findings, we argue......This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice...... that workshops provide a platform that can aid researchers in identifying and exploring relevant factors in a given domain by providing means for understanding complex work and knowledge processes that are supported by technology (for example, e-learning). The approach supports identifying factors...

Log4J

CERN Document Server

Perry, Steven

2009-01-01

Log4j has been around for a while now, and it seems like so many applications use it. I've used it in my applications for years now, and I'll bet you have too. But every time I need to do something with log4j I've never done before I find myself searching for examples of how to do whatever that is, and I don't usually have much luck. I believe the reason for this is that there is a not a great deal of useful information about log4j, either in print or on the Internet. The information is too simple to be of real-world use, too complicated to be distilled quickly (which is what most developers

77 FR 46444 - Gastroenterology Regulatory Endpoints and the Advancement of Therapeutics (GREAT); Public Workshop

Science.gov (United States)

2012-08-03

... discussion of a single relevant disease area. The goal of the workshop day dedicated to eosinophilic... day dedicated to pediatric inflammatory bowel disease (IBD) is to discuss issues related to the extrapolation of efficacy data from adult to pediatric patients, the definition and measurement of treatment...

PREFACE: 2nd Workshop on Germanium Detectors and Technologies

Science.gov (United States)

Abt, I.; Majorovits, B.; Keller, C.; Mei, D.; Wang, G.; Wei, W.

2015-05-01

The 2nd workshop on Germanium (Ge) detectors and technology was held at the University of South Dakota on September 14-17th 2014, with more than 113 participants from 8 countries, 22 institutions, 15 national laboratories, and 8 companies. The participants represented the following big projects: (1) GERDA and Majorana for the search of neutrinoless double-beta decay (0νββ) (2) SuperCDMS, EDELWEISS, CDEX, and CoGeNT for search of dark matter; (3) TEXONO for sub-keV neutrino physics; (4) AGATA and GRETINA for gamma tracking; (5) AARM and others for low background radiation counting; (5) as well as PNNL and LBNL for applications of Ge detectors in homeland security. All participants have expressed a strong desire on having better understanding of Ge detector performance and advancing Ge technology for large-scale applications. The purpose of this workshop was to leverage the unique aspects of the underground laboratories in the world and the germanium (Ge) crystal growing infrastructure at the University of South Dakota (USD) by brining researchers from several institutions taking part in the Experimental Program to Stimulate Competitive Research (EPSCoR) together with key leaders from international laboratories and prestigious universities, working on the forefront of the intensity to advance underground physics focusing on the searches for dark matter, neutrinoless double-beta decay (0νββ), and neutrino properties. The goal of the workshop was to develop opportunities for EPSCoR institutions to play key roles in the planned world-class research experiments. The workshop was to integrate individual talents and existing research capabilities, from multiple disciplines and multiple institutions, to develop research collaborations, which includes EPSCor institutions from South Dakota, North Dakota, Alabama, Iowa, and South Carolina to support multi-ton scale experiments for future. The topic areas covered in the workshop were: 1) science related to Ge

Unsupervised signature extraction from forensic logs

NARCIS (Netherlands)

Thaler, S.M.; Menkovski, V.; Petkovic, M.; Altun, Y.; Das, K.; Mielikäinen, T.; Malerba, D.; Stefanowski, J.; Read, J.; Žitnik, M.; Ceci, M.

2017-01-01

Signature extraction is a key part of forensic log analysis. It involves recognizing patterns in log lines such that log lines that originated from the same line of code are grouped together. A log signature consists of immutable parts and mutable parts. The immutable parts define the signature, and

7th International Workshop on Natural Computing

CERN Document Server

Hagiya, Masami

2015-01-01

This book highlights recent advances in natural computing, including biology and its theory, bio-inspired computing, computational aesthetics, computational models and theories, computing with natural media, philosophy of natural computing and educational technology. It presents extended versions of the best papers selected from the symposium “7th International Workshop on Natural Computing” (IWNC7), held in Tokyo, Japan, in 2013. The target audience is not limited to researchers working in natural computing but also those active in biological engineering, fine/media art design, aesthetics and philosophy.

Workshop on environmental research for actinide elements

International Nuclear Information System (INIS)

Watters, R.L.

1981-09-01

The discussions in this fifth workshop were directed to the advances which have been made in the environmental chemistry of plutonium and to the feasibility and worth of developing environmental transport models which might serve as predictive tools for long term behavior and as guides for future research needs. Two plutonium models of the soil/plant pathway were presented for critique and as examples of possible approaches. Reports of the following four panels are presented in this proceedings: model development; marine; terrestrial and freshwater/groundwater

Workshop meeting

International Nuclear Information System (INIS)

Veland, Oeystein

2004-04-01

1-2 September 2003 the Halden Project arranged a workshop on 'Innovative Human-System Interfaces and their Evaluation'. This topic is new in the HRP 2003-2005 programme, and it is important to get feedback from member organizations to the work that is being performed in Halden. It is also essential that relevant activities and experiences in this area from the member organizations are shared with the Halden staff and other HRP members. Altogether 25 persons attended the workshop. The workshop had a mixture of presentations and discussions, and was chaired by Dominique Pirus of EDF, France. Day one focused on the HRP/IFE activities on Human-System Interface design, including Function-oriented displays, Ecological Interface Design, Task-oriented displays, as well as work on innovative display solutions for the oil and gas domain. There were also presentations of relevant work in France, Japan and the Czech Republic. The main focus of day two was the verification and validation of human-system interfaces, with presentations of work at HRP on Human-Centered Validation, Criteria-Based System Validation, and Control Room Verification and Validation. The chairman concluded that it was a successful workshop, although one could have had more time for discussions. The Halden Project got valuable feedback and viewpoints on this new topic during the workshop, and will consider all recommendations related to the future work in this area. (Author)

Log-balanced combinatorial sequences

Directory of Open Access Journals (Sweden)

Tomislav Došlic

2005-01-01

Full Text Available We consider log-convex sequences that satisfy an additional constraint imposed on their rate of growth. We call such sequences log-balanced. It is shown that all such sequences satisfy a pair of double inequalities. Sufficient conditions for log-balancedness are given for the case when the sequence satisfies a two- (or more- term linear recurrence. It is shown that many combinatorially interesting sequences belong to this class, and, as a consequence, that the above-mentioned double inequalities are valid for all of them.

Fiscal 1998 engineer interexchange project (coal mine technology field). International interexchange project (Workshop in Japan); 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya). Kokusai koryu jigyo (kokunai workshop)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the workshop and technical tour held in Japan for technical interexchange of domestic and overseas engineers. From the information obtained, the higher productivity of coal mines is dependent on selective mining under blessed geological conditions, however, basically establishment of an advanced management technique for inexpensive stable operation. Both preliminary collection of geological information and introduction of advanced facilities even under unstable conditions are necessary. The balance and optimization of the whole system, and an excellent human nature for operation are also essential. Use of roof bolt supports is diffusing as improvement technology of excavation speed and roof control technology over the world. However, for introduction of new technologies, collection of test results and various kinds of training are necessary. Methane gas in coal seams as the main theme of the Hokkaido workshop is a precious unused natural resource, and important for prevention of global warming and coal mine protection measures. Its use is dependent on development of gas drainage technology. (NEDO)

Advances and synergy of high pressure sciences at synchrotron sources

International Nuclear Information System (INIS)

Liu, H.; Ehm, L.; Duffy, T.; Crichton, W.; Aoki, K.

2009-01-01

Introductory overview to the special issue papers on high-pressure sciences and synchrotron radiation. High-pressure research in geosciences, materials science and condensed matter physics at synchrotron sources is experiencing growth and development through synergistic efforts around the world. A series of high-pressure science workshops were organized in 2008 to highlight these developments. One of these workshops, on 'Advances in high-pressure science using synchrotron X-rays', was held at the National Synchrotron Light Source (NSLS), Brookhaven National Laboratory, USA, on 4 October 2008. This workshop was organized in honour of Drs Jingzhu Hu and Quanzhong Guo in celebration of their retirement after up to 18 years of dedicated service to the high-pressure community as beamline scientists at X17 of NSLS. Following this celebration of the often unheralded role of the beamline scientist, a special issue of the Journal of Synchrotron Radiation on Advances and Synergy of High-Pressure Sciences at Synchrotron Sources was proposed, and we were pleased to invite contributions from colleagues who participated in the workshop as well as others who are making similar efforts at synchrotron sources worldwide.

Workshop on instrumentation and analyses for a nuclear fuel reprocessing hot pilot plant

International Nuclear Information System (INIS)

Babcock, S.M.; Feldman, M.J.; Wymer, R.G.; Hoffman, D.

1980-05-01

In order to assist in the study of instrumentation and analytical needs for reprocessing plants, a workshop addressing these needs was held at Oak Ridge National Laboratory from May 5 to 7, 1980. The purpose of the workshop was to incorporate the knowledge of chemistry and of advanced measurement techniques held by the nuclear and radiochemical community into ideas for improved and new plant designs for both process control and inventory and safeguards measurements. The workshop was athended by experts in nuclear and radiochemistry, in fuel recycle plant design, and in instrumentation and analysis. ORNL was a particularly appropriate place to hold the workshop since the Consolidated Fuel Reprocessing Program (CFRP) is centered there. Requirements for safeguarding the special nuclear materials involved in reprocessing, and for their timely measurement within the process, within the reprocessing facility, and at the facility boundaries are being studied. Because these requirements are becoming more numerous and stringent, attention is also being paid to the analytical requirements for these special nuclear materials and to methods for measuring the physical parameters of the systems containing them. In order to provide a focus for the consideration of the workshop participants, the Hot Experimental Facility (HEF) being designed conceptually by the CFRP was used as a basis for consideration and discussions

LOG2MARKUP: State module to transform a Stata text log into a markup document

DEFF Research Database (Denmark)

2016-01-01

log2markup extract parts of the text version from the Stata log command and transform the logfile into a markup based document with the same name, but with extension markup (or otherwise specified in option extension) instead of log. The author usually uses markdown for writing documents. However...

Third workshop on geothermal reservoir engineering: Proceedings

Energy Technology Data Exchange (ETDEWEB)

Ramey, H.J. Jr.; Kruger, P. (eds.)

1977-12-15

The Third Workshop on Geothermal Reservoir Engineering convened at Stanford University on December 14, 1977, with 104 attendees from six nations. In keeping with the recommendations expressed by the participants at the Second Workshop, the format of the Workshop was retained, with three days of technical sessions devoted to reservoir physics, well and reservoir testing, field development, and mathematical modeling of geothermal reservoirs. The program presented 33 technical papers, summaries of which are included in these Proceedings. Although the format of the Workshop has remained constant, it is clear from a perusal of the Table of Contents that considerable advances have occurred in all phases of geothermal reservoir engineering over the past three years. Greater understanding of reservoir physics and mathematical representations of vapor-dominated and liquid-dominated reservoirs are evident; new techniques for their analysis are being developed, and significant field data from a number of newer reservoirs are analyzed. The objectives of these workshops have been to bring together researchers active in the various physical and mathematical disciplines comprising the field of geothermal reservoir engineering, to give the participants a forum for review of progress and exchange of new ideas in this rapidly developing field, and to summarize the effective state of the art of geothermal reservoir engineering in a form readily useful to the many government and private agencies involved in the development of geothermal energy. To these objectives, the Third Workshop and these Proceedings have been successfully directed. Several important events in this field have occurred since the Second Workshop in December 1976. The first among these was the incorporation of the Energy Research and Development Administration (ERDA) into the newly formed Department of Energy (DOE) which continues as the leading Federal agency in geothermal reservoir engineering research. The Third

Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement.

Science.gov (United States)

Shatkin, J A; Ong, Kimberly J; Beaudrie, Christian; Clippinger, Amy J; Hendren, Christine Ogilvie; Haber, Lynne T; Hill, Myriam; Holden, Patricia; Kennedy, Alan J; Kim, Baram; MacDonell, Margaret; Powers, Christina M; Sharma, Monita; Sheremeta, Lorraine; Stone, Vicki; Sultan, Yasir; Turley, Audrey; White, Ronald H

2016-08-01

The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article. © 2016 Society for Risk Analysis.

Proceedings of the workshop on the nuclear sciences of the heaviest elements

Energy Technology Data Exchange (ETDEWEB)

Nagame, Yuichiro; Haba, Hiromitsu; Ikezoe, Hiroshi [eds.

2000-03-01

The workshop on the nuclear sciences of the heaviest elements took place on July 21-22, 1999 at the Japan Atomic Energy Research Institute (JAERI), Tokai. Approximately 40 scientists and 15 graduate students participated in the workshop which was organized by the Advanced Science Research Center, JAERI. The successful syntheses of three new super-heavy elements in 1999, Z=114 at the Joint Institute for Nuclear Research in Dubna, Russia, and Z=118 (with Z=116 following from {alpha}-decay of Z=118) at the Lawrence Berkeley National Laboratory (LBNL) in USA, are tremendous progress in the field of the heavy element research. The 1st International Conference on the Chemistry and Physics of the Transactinide Elements (TAN99) was held in Germany from September 26 to 30, 1999 to discuss in a larger context all scientific aspects of the heaviest elements. Thus, it was timely to hold the present domestic workshop to summarize what has been done in recent years, to see what has come true, and to discuss the perspectives in the near feature. The subjects in the workshop were classified into; (1) synthesis of heavy elements, (2) decay properties of heavy nuclei, (3) chemistry of the heaviest elements, and (4) future plans of the heavy element research in Japan. This volume contains the papers presented in the workshop. The 14 papers are indexed individually. (J.P.N.)

The diversity and disparity in biomedical informatics (DDBI) workshop.

Science.gov (United States)

Southerland, William M; Swamidass, S Joshua; Payne, Philip R O; Wiley, Laura; Williams-DeVane, ClarLynda

2018-01-01

The Diversity and Disparity in Biomedical Informatics (DDBI) workshop will be focused on complementary and critical issues concerned with enhancing diversity in the informatics workforce as well as diversity in patient cohorts. According to the National Institute of Minority Health and Health Disparities (NIMHD) at the NIH, diversity refers to the inclusion of the following traditionally underrepresented groups: African Americans/Blacks, Asians (>30 countries), American Indian or Alaska Native, Native Hawaiian or Other Pacific Islander, Latino or Hispanic (20 countries). Gender, culture, and socioeconomic status are also important dimensions of diversity, which may define some underrepresented groups. The under-representation of specific groups in both the biomedical informatics workforce as well as in the patient-derived data that is being used for research purposes has contributed to an ongoing disparity; these groups have not experienced equity in contributing to or benefiting from advancements in informatics research. This workshop will highlight innovative efforts to increase the pool of minority informaticians and discuss examples of informatics research that addresses the health concerns that impact minority populations. This workshop topics will provide insight into overcoming pipeline issues in the development of minority informaticians while emphasizing the importance of minority participation in health related research. The DDBI workshop will occur in two parts. Part I will discuss specific minority health & health disparities research topics and Part II will cover discussions related to overcoming pipeline issues in the training of minority informaticians.

AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study: Final Report

Energy Technology Data Exchange (ETDEWEB)

Schey, Stephen [Idaho National Laboratory (INL), Idaho Falls, ID (United States); Francfort, Jim [Idaho National Laboratory (INL), Idaho Falls, ID (United States)

2015-06-01

Collect and evaluate data on federal fleet operations as part of the Advanced Vehicle Testing Activity’s Federal Fleet Vehicle Data Logging and Characterization Study. The Advanced Vehicle Testing Activity study seeks to collect and evaluate data to validate the utilization of advanced plug-in electric vehicle (PEV) transportation. This report summarizes the fleets studied to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of PEVs into the agencies’ fleets. Individual observations of these selected vehicles provide the basis for recommendations related to electric vehicle adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (collectively referred to as PEVs) can fulfill the mission requirements.

Experimental equipment for an advanced ISOL facility

International Nuclear Information System (INIS)

Baktash, C.; Lee, I.Y.; Rehm, K.E.

1999-01-01

This report summarizes the proceedings and recommendations of the Workshop on the Experimental Equipment for an Advanced ISOL Facility which was held at Lawrence Berkeley National Laboratory on July 22--25, 1998. The purpose of this workshop was to discuss the performance requirements, manpower and cost estimates, as well as a schedule of the experimental equipment needed to fully exploit the new physics which can be studied at an advanced ISOL facility. An overview of the new physics opportunities that would be provided by such a facility has been presented in the White Paper that was issued following the Columbus Meeting. The reactions and experimental techniques discussed in the Columbus White Paper served as a guideline for the formulation of the detector needs at the Berkeley Workshop. As outlined a new ISOL facility with intense, high-quality beams of radioactive nuclei would provide exciting new research opportunities in the areas of: the nature of nucleonic matter; the origin of the elements; and tests of the Standard Model. After an introductory section, the following equipment is discussed: gamma-ray detectors; recoil separators; magnetic spectrographs; particle detectors; targets; and apparatus using non-accelerated beams

Workshop on Computational Optimization

CERN Document Server

2016-01-01

This volume is a comprehensive collection of extended contributions from the Workshop on Computational Optimization 2014, held at Warsaw, Poland, September 7-10, 2014. The book presents recent advances in computational optimization. The volume includes important real problems like parameter settings for controlling processes in bioreactor and other processes, resource constrained project scheduling, infection distribution, molecule distance geometry, quantum computing, real-time management and optimal control, bin packing, medical image processing, localization the abrupt atmospheric contamination source and so on. It shows how to develop algorithms for them based on new metaheuristic methods like evolutionary computation, ant colony optimization, constrain programming and others. This research demonstrates how some real-world problems arising in engineering, economics, medicine and other domains can be formulated as optimization tasks.

Workshop on Computational Optimization

CERN Document Server

2015-01-01

Our everyday life is unthinkable without optimization. We try to minimize our effort and to maximize the achieved profit. Many real world and industrial problems arising in engineering, economics, medicine and other domains can be formulated as optimization tasks. This volume is a comprehensive collection of extended contributions from the Workshop on Computational Optimization 2013. It presents recent advances in computational optimization. The volume includes important real life problems like parameter settings for controlling processes in bioreactor, resource constrained project scheduling, problems arising in transport services, error correcting codes, optimal system performance and energy consumption and so on. It shows how to develop algorithms for them based on new metaheuristic methods like evolutionary computation, ant colony optimization, constrain programming and others.

EDITORIAL: 15th European Workshop on Micromechanics (MME)

Science.gov (United States)

Puers, Bob

2005-07-01

This special issue of Journal of Micromechanics and Microengineering is entirely devoted to the fifteenth European Workshop on Micromechanics (MME), which was held in Leuven, at the Faculty Club, 5-7 September 2004. In this issue you will find a selection of papers presented at this workshop. The MME Workshop is organized every year to gather mostly European scientists and people from industry to discuss topics related to micromachining and microengineering in an informal manner. The first workshop was held at Twente University, the Netherlands, in 1989. The success of that event inaugurated a series of workshops traveling all over Europe. Looking back on the fifteen years of micromachining it is evident that the field has become more mature. More application driven research is now replacing the basic pure technology driven research we once got so excited about. Yet, half of the contributions still cover problems related to fabrication, production and reliability. Traditionally, the workshop aims to bring together young scientists in the field, with emphasis on discussions and communications in a friendly and informal atmosphere. The goal is to stimulate and to improve knowledge in the field, as well as to promote friendships between researchers. This edition of the workshop was no different. More than 70 papers were contributed, and it was decided to widen the scope with contributions also covering non-silicon technologies. This trend had already been informally introduced some years ago. After the third edition, it was decided to open up a selection of the contributed papers to a broader public by publishing them in a special issue of Journal of Micromechanics and Microengineering, and this has continued to the present day. Since the purpose of the workshop clearly is to stimulate younger scientists to enter the field, even immature research is presented there. The selection in this issue, however, aims to bring to you the more advanced level research work. Even

German-Catalan workshop on epigenetics and cancer.

Science.gov (United States)

Vizoso, Miguel; Esteller, Manel

2013-09-01

In the First German-Catalan Workshop on Epigenetics and Cancer held in Heidelberg, Germany (June 17-19, 2013), cutting-edge laboratories (PEBC, IMPPC, DKFZ, and the Collaborative Research Centre Medical Epigenetics of Freiburg) discussed the latest breakthroughs in the field. The importance of DNA demethylation, non-coding and imprinted genes, metabolic stress, and cell transdifferentiation processes in cancer and non-cancer diseases were addressed in several lectures in a very participative and dynamic atmosphere.   The meeting brought together leading figures in the field of cancer epigenetics to present their research work from the last five years. Experts in different areas of oncology described important advances in colorectal, lung, neuroblastoma, leukemia, and lymphoma cancers. The workshop also provided an interesting forum for pediatrics, and focused on the need to improve the treatment of childhood tumors in order to avoid, as far as possible, brain damage and disruption of activity in areas of high plasticity. From the beginning, the relevance of "omics" and the advances in genome-wide analysis platforms, which allow cancer to be studied in a more comprehensive and inclusive way, was very clear. Modern "omics" offer the possibility of identifying metastases of uncertain origin and establishing epigenetic signatures linked to a specific cluster of patients with a particular prognosis. In this context, invited speakers described novel tumor-associated histone variants and DNA-specific methylation, highlighting their close connection with other processes such as cell-lineage commitment and stemness.

Radiometric well logging instruments

International Nuclear Information System (INIS)

Davydov, A.V.

1975-01-01

The technical properties of well instruments for radioactive logging used in the radiometric logging complexes PKS-1000-1 (''Sond-1'') and PRKS-2 (''Vitok-2'') are described. The main features of the electric circuit of the measuring channels are given

Hardwood log supply: a broader perspective

Science.gov (United States)

Iris Montague; Adri Andersch; Jan Wiedenbeck; Urs. Buehlmann

2015-01-01

At regional and state meetings we talk with others in our business about the problems we face: log exports, log quality, log markets, logger shortages, cash flow problems, the weather. These are familiar talking points and real and persistent problems. But what is the relative importance of these problems for log procurement in different regions of...

Joint ICTP-IAEA advanced workshop on model codes for spallation reactions

International Nuclear Information System (INIS)

Filges, D.; Leray, S.; Yariv, Y.; Mengoni, A.; Stanculescu, A.; Mank, G.

2008-08-01

The International Atomic Energy Agency (IAEA) and the Abdus Salam International Centre for Theoretical Physics (ICTP) organised an expert meeting at the ICTP from 4 to 8 February 2008 to discuss model codes for spallation reactions. These nuclear reactions play an important role in a wide domain of applications ranging from neutron sources for condensed matter and material studies, transmutation of nuclear waste and rare isotope production to astrophysics, simulation of detector set-ups in nuclear and particle physics experiments, and radiation protection near accelerators or in space. The simulation tools developed for these domains use nuclear model codes to compute the production yields and characteristics of all the particles and nuclei generated in these reactions. These codes are generally Monte-Carlo implementations of Intra-Nuclear Cascade (INC) or Quantum Molecular Dynamics (QMD) models, followed by de-excitation (principally evaporation/fission) models. Experts have discussed in depth the physics contained within the different models in order to understand their strengths and weaknesses. Such codes need to be validated against experimental data in order to determine their accuracy and reliability with respect to all forms of application. Agreement was reached during the course of the workshop to organise an international benchmark of the different models developed by different groups around the world. The specifications of the benchmark, including the set of selected experimental data to be compared to the models, were also defined during the workshop. The benchmark will be organised under the auspices of the IAEA in 2008, and the first results will be discussed at the next Accelerator Applications Conference (AccApp'09) to be held in Vienna in May 2009. (author)

Workshop: Western hemisphere network of bird banding programs

Science.gov (United States)

Celis-Murillo, A.

2007-01-01

? workshop will continue addressing issues surrounding the coordination of an Americas? approach to bird banding and will review in detail the advances made on the first workshop such as, coordination of bands and markers, coordination in recovery reporting, permit issues, data management and data sharing and archiving, data security, training, etc. Workshop Goals: Build on accomplishments of the network?s first workshop (Oct 8-9, 2006). Identify and explore new opportunities for data sharing, data archiving, data access, training, etc. Initiate strategies to support international collaboration and coordination amongst bird banding programs in the Western Hemisphere. Workshop structure: One day workshop of guided discussions. Participants: Representatives of government agencies, program managers and NGOs.

PREFACE: 14th Micromechanics Europe Workshop (MME'03)

Science.gov (United States)

Wolffenbuttel, R. F.

2004-09-01

This special issue of the Journal of Micromechanics and Microengineering is devoted to the 14th Micromechanics Europe Workshop (MME'03), which was held at Delft University of Technology, The Netherlands on 2-4 November 2003. Papers have been selected from this workshop for presentation in this special issue. After a careful review by the MME'03 programme committee, 53 submissions were selected for poster presentation at the workshop in addition to 6 invited presentations. These covered the many aspects of our exciting field: technology, simulation, system design, fabrication and characterization in a wide range of applications. These contributions confirm a trend from technology-driven towards application-driven technological research. This trend has become possible because of the availability of mature fabrication technologies for micromechanical structures and is reflected by the presentations of some of the invited speakers. There were invited lectures about applications in the medical field, automotive and copiers, which provide evidence of the relevance of our work in society. Nevertheless, development of technologies rightfully remains a core activity of this workshop. This applies to both the introduction of new technologies, as was reflected by invited presentations on new trends in RIE and nanotechnology, and the addressing of manufacturing issues using available techniques, which will be demonstrated to be crucial in automotive applications. Out of these 59 papers 21 have been selected for presentation in this special issue. Since the scope of the workshop is somewhat wider than that of the journal, selection was based not only on the quality of the work, but also on suitability for presentation in the journal. Moreover, at the workshop, student presentation of research at an early stage was strongly encouraged, whereas publication of work in this journal requires a more advanced level. I would like to express my appreciation for the outstanding efforts

Summary Report of the INL-JISEA Workshop on Nuclear Hybrid Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Antkowiak, M.; Ruth, M.; Boardman, R.; Bragg-Sitton, S.; Cherry, R.; Shunn, L.

2012-07-01

The Institute for Nuclear Energy Science and Technology (INEST) and the Joint Institute for Strategic Energy Analysis (JISEA) co-sponsored an international workshop to identify research topics important in advancing the potential use of hybrid systems with a specific focus on nuclear-renewable hybrid systems. The workshop included presentations ranging from energy challenges and research and development directions being pursued by nations to multiple options for hybrid systems. Those options include one that is being commercialized to other opportunities and analysis results quantifying them. The workshop also involved two breakout sessions--one focused on thermal energy management issues especially at unit-operation scale and the second focused on system operations issues including system controls, regulatory issues, technical and economic analysis, and market challenges. A discussion involving the full group focused on more general issues such as societal involvement and participation. Key criteria for selecting hybrid energy system projects and metrics for comparing them were also identified by the full group.

Workshop on Direct Contact Heat Transfer at the Solar Energy Research Institute

CERN Document Server

Boehm, R

1988-01-01

to increase the use of direct contact processes, the National Science Foundation sup­ ported a workshop on direct contact heat transfer at the Solar Energy Research Insti­ tute in the summer of 1985. We served as organizers for this workshop, which em­ phasized an area of thermal engineering that, in our opinion, has great promise for the future, but has not yet reached the point of wide-spread commercial application. Hence, a summary of the state of knowledge at this point is timely. The workshop had a dual objective: 1. To summarize the current state of knowledge in such a form that industrial practi­ tioners can make use of the available information. 2. To indicate the research and development needed to advance the state-of-the-art, indicating not only what kind of research is needed, but also the industrial poten­ tial that could be realized if the information to be obtained through the proposed research activities were available.

The role of advanced nuclear power technologies in developing countries: Criteria and design requirements

International Nuclear Information System (INIS)

1990-02-01

The document includes the papers presented at the following two technical committee meetings organized by the IAEA: Technical Committee Meeting and Workshop on Criteria for the Introduction of Advanced Nuclear Power Technologies for Specific Applications in Developing Countries, Vienna, 27-30 June 1988 (14 papers) and Technical Committee Meeting and Workshop on Design Requirements for the Application of Advanced Concepts in Developing Countries, Vienna, 6-9 December 1988 (16 papers). A separate abstract was prepared for each of these papers

Current Writing: Text and Reception in Southern Africa: Advanced ...

African Journals Online (AJOL)

Current Writing: Text and Reception in Southern Africa: Advanced Search. Journal Home > Current Writing: Text and Reception in Southern Africa: Advanced Search. Log in or Register to get access to full text downloads.

EERE Quality Control Workshop Final Report: Proceedings from the EERE Quality Control Workshop, in support of the DOE Clean Energy Manufacturing Initiative; Golden, Colorado, December 9-10, 2013

Energy Technology Data Exchange (ETDEWEB)

2014-05-01

The U.S. Department of Energy Office of Energy Efficiency & Renewable Energy (EERE) has recognized the cross-cutting, pre-competitive and enabling nature of quality control for a wide range of clean energy technologies. As such, the Fuel Cell Technologies Office, Solar Energy Technologies Office, Vehicle Technologies Office, Building Technologies Office, and Advanced Manufacturing Office decided to explore needs and potential cross-office synergies in this area by holding the EERE Quality Control Workshop, in support of the DOE Clean Energy Manufacturing Initiative. This report summarizes the purpose and scope of the workshop; reviews the current status and state-of-the-art for in-line quality control; summarizes the results from three breakout sessions; and presents conclusions and recommendations.

Semi-automatic logarithmic converter of logs

International Nuclear Information System (INIS)

Gol'dman, Z.A.; Bondar's, V.V.

1974-01-01

Semi-automatic logarithmic converter of logging charts. An original semi-automatic converter was developed for use in converting BK resistance logging charts and the time interval, ΔT, of acoustic logs from a linear to a logarithmic scale with a specific ratio for subsequent combining of them with neutron-gamma logging charts in operative interpretation of logging materials by a normalization method. The converter can be used to increase productivity by giving curves different from those obtained in manual, pointwise processing. The equipment operates reliably and is simple in use. (author)

Power to the logs!

CERN Multimedia

CERN. Geneva; MACMAHON, Joseph

2015-01-01

Are you tired of using grep, vi and emacs to read your logs? Do you feel like you’re missing the big picture? Does the word "statistics" put a smile on your face? Then it’s time to give power to the logs!

Proceedings of twelfth ISMAS symposium cum workshop on mass spectrometry

International Nuclear Information System (INIS)

Alamelu, D.; Jaison, P.G.; Aggarwal, S.K.

2007-03-01

Mass Spectrometry is an important analytical tool and has encompassed almost all branches of science and technology including Agricultural, biology, Chemistry, Earth sciences, environment, Forensic Science, Medical Sciences, Hydrology, Nuclear Technology, Oceanography, Physics etc. Recent advancements in the instrumentation of Mass Spectrometry have further strengthened its role for various applications. It is indeed a matter of great pleasure to present this special Issue of ISMAS Bulletin which is brought out on the occasion of the 12th ISMAS Symposium cum Workshop on Mass spectrometry (12th ISMAS-WS 2007) being held at Cidade-de-Goa, Dona Paula, Goa from March 25 to 30, 2007 in association with National Institute of Oceanography, Goa. This Symposium cum Workshop is co-sponsored by Scientific Departments of Government of India. Papers relevant to INIS are indexed separately

Laue 2007: international workshop on advanced Laue diffraction in frontier science

International Nuclear Information System (INIS)

Adachi, S.I.; Akgul, G.; Aksoy, F.; Andersen, K.; Andersson, M.; Anfinrud, Ph.; Baruchel, J.; Bastie, P.; Bau, R.; Blakeley, M.; Bourgeois, D.; Brau, D.; Bravin, A.; Cammarata, M.; Christensen, M.; Cole, J.; Courtois, P.; Cousson, A.; Eggonopoulos-Papadopoulos, B.; Daoud-Aladine, M.A.; Dera, P.; Feng, R.; Fiedler, St.; Fischer, H.; Fisher, St.; Folami, S.; Fosu, M.A.; Fuente, F.; Fullagar, W.; Fulla Marsa, D.; Ghosh, R.; Giles, C.; Goossens, D.; Goujon, A.; Gutmann, M.; Heger, G.; Henry, E.; Hewat, A.; Hossmann, Ch.; Ivanov, A.; Jauch, W.; Jorgensen, R.; Katona, G.; Keen, D.; Kong, Q.; Koshihara, Sh.Y.; Lauss, B.; Laue, M.V.; Lecomte, C.; Legrand, V.; Lemee-Cailleau, M.H.; Marmeggi, J.C.; Martinez-Criado, G.; Mason, S.; McIntyre, G.; Mailleur, F.; Micha, J.S.; Moffat, K.; Mohammed Mustapha, A.; Ouladdiaf, B.; Pahl, R.; Parise, J.; Pearson, A.; Pecaut, J.; Popov, A.; Prokleska, J.; Raitman, E.; Ren, Z.; Rodriguez-Carvajal, J.; Sasaki, J.; Schmidt, M.; Schotte, F.; Stirling, W.; Suominen Fuller, M.; Tanaka, I.; Timmins, P.; Tomking, P.; Turner, M.; Van Thor, J.; Vettier, Ch.; Wildes, A.; Wilson, Ch.; Wohri, A.; Wulf, M.; Zhao, Y.

2007-01-01

Laue diffraction is currently undergoing a lively renaissance due to new instrumental developments at both synchrotron X-ray and neutron sources. The aim of the workshop Laue-2007 is to offer state-of-the-art experimental methods and hands-on experience of data analysis for exploration, using single-crystal Laue diffraction, of the crystalline structure of complex materials in extreme cases. The oral sessions cover the following topics: -) history and renaissance of Laue diffraction, -) modern X-ray techniques, -) modern neutron techniques, -) applications, -) analysis and software demonstrations including hands-on experience, and -) future directions. This document gathers the abstracts of the presentations and of the posters

Laue 2007: international workshop on advanced Laue diffraction in frontier science

Energy Technology Data Exchange (ETDEWEB)

Adachi, S I; Akgul, G; Aksoy, F; Andersen, K; Andersson, M; Anfinrud, Ph; Baruchel, J; Bastie, P; Bau, R; Blakeley, M; Bourgeois, D; Brau, D; Bravin, A; Cammarata, M; Christensen, M; Cole, J; Courtois, P; Cousson, A; Eggonopoulos-Papadopoulos, B; Daoud-Aladine, M A; Dera, P; Feng, R; Fiedler, St; Fischer, H; Fisher, St; Folami, S; Fosu, M A; Fuente, F; Fullagar, W; Fulla Marsa, D; Ghosh, R; Giles, C; Goossens, D; Goujon, A; Gutmann, M; Heger, G; Henry, E; Hewat, A; Hossmann, Ch; Ivanov, A; Jauch, W; Jorgensen, R; Katona, G; Keen, D; Kong, Q; Koshihara, Sh Y; Lauss, B; Laue, M V; Lecomte, C; Legrand, V; Lemee-Cailleau, M H; Marmeggi, J C; Martinez-Criado, G; Mason, S; McIntyre, G; Mailleur, F; Micha, J S; Moffat, K; Mohammed Mustapha, A; Ouladdiaf, B; Pahl, R; Parise, J; Pearson, A; Pecaut, J; Popov, A; Prokleska, J; Raitman, E; Ren, Z; Rodriguez-Carvajal, J; Sasaki, J; Schmidt, M; Schotte, F; Stirling, W; Suominen Fuller, M; Tanaka, I; Timmins, P; Tomking, P; Turner, M; Van Thor, J; Vettier, Ch; Wildes, A; Wilson, Ch; Wohri, A; Wulf, M; Zhao, Y

2007-07-01

Laue diffraction is currently undergoing a lively renaissance due to new instrumental developments at both synchrotron X-ray and neutron sources. The aim of the workshop Laue-2007 is to offer state-of-the-art experimental methods and hands-on experience of data analysis for exploration, using single-crystal Laue diffraction, of the crystalline structure of complex materials in extreme cases. The oral sessions cover the following topics: -) history and renaissance of Laue diffraction, -) modern X-ray techniques, -) modern neutron techniques, -) applications, -) analysis and software demonstrations including hands-on experience, and -) future directions. This document gathers the abstracts of the presentations and of the posters.

A method of estimating log weights.

Science.gov (United States)

Charles N. Mann; Hilton H. Lysons

1972-01-01

This paper presents a practical method of estimating the weights of logs before they are yarded. Knowledge of log weights is required to achieve optimum loading of modern yarding equipment. Truckloads of logs are weighed and measured to obtain a local density index (pounds per cubic foot) for a species of logs. The density index is then used to estimate the weights of...

California-Nevada uranium logging. Final report

International Nuclear Information System (INIS)

1981-04-01

The purpose of this project was to obtain geophysical logs of industry drill holes to assess the uranium resource potential of geologic formations of interest. The work was part of the US Department of Energy's National Uranium Resource Evaluation (NURE) Program. The principal objective of the logging program was to determine radioelement grade of formations through natural gamma ray detectors. Supplementary information was obtained from resistivity (R), self-potential (SP), point resistance (RE), and neutron density (NN) logs for formation interpretation. Additional data for log interpretation was obtained from caliper logs, casing schedules, and downhole temperature. This data was obtained from well operators when available, with new logs obtained where not formerly available. This report contains a summary of the project and data obtained to date

8th International Workshop on Natural Computing

CERN Document Server

Hagiya, Masami

2016-01-01

This book highlights recent advances in natural computing, including biology and its theory, bio-inspired computing, computational aesthetics, computational models and theories, computing with natural media, philosophy of natural computing, and educational technology. It presents extended versions of the best papers selected from the “8th International Workshop on Natural Computing” (IWNC8), a symposium held in Hiroshima, Japan, in 2014. The target audience is not limited to researchers working in natural computing but also includes those active in biological engineering, fine/media art design, aesthetics, and philosophy.

International Workshop on Elliptic and Parabolic Equations

CERN Document Server

Schrohe, Elmar; Seiler, Jörg; Walker, Christoph

2015-01-01

This volume covers the latest research on elliptic and parabolic equations and originates from the international Workshop on Elliptic and Parabolic Equations, held September 10-12, 2013 at the Leibniz Universität Hannover. It represents a collection of refereed research papers and survey articles written by eminent scientist on advances in different fields of elliptic and parabolic partial differential equations, including singular Riemannian manifolds, spectral analysis on manifolds, nonlinear dispersive equations, Brownian motion and kernel estimates, Euler equations, porous medium type equations, pseudodifferential calculus, free boundary problems, and bifurcation analysis.

Meeting Report--NASA Radiation Biomarker Workshop

Energy Technology Data Exchange (ETDEWEB)

Straume, Tore; Amundson, Sally A,; Blakely, William F.; Burns, Frederic J.; Chen, Allen; Dainiak, Nicholas; Franklin, Stephen; Leary, Julie A.; Loftus, David J.; Morgan, William F.; Pellmar, Terry C.; Stolc, Viktor; Turteltaub, Kenneth W.; Vaughan, Andrew T.; Vijayakumar, Srinivasan; Wyrobek, Andrew J.

2008-05-01

A summary is provided of presentations and discussions from the NASA Radiation Biomarker Workshop held September 27-28, 2007, at NASA Ames Research Center in Mountain View, California. Invited speakers were distinguished scientists representing key sectors of the radiation research community. Speakers addressed recent developments in the biomarker and biotechnology fields that may provide new opportunities for health-related assessment of radiation-exposed individuals, including for long-duration space travel. Topics discussed include the space radiation environment, biomarkers of radiation sensitivity and individual susceptibility, molecular signatures of low-dose responses, multivariate analysis of gene expression, biomarkers in biodefense, biomarkers in radiation oncology, biomarkers and triage following large-scale radiological incidents, integrated and multiple biomarker approaches, advances in whole-genome tiling arrays, advances in mass-spectrometry proteomics, radiation biodosimetry for estimation of cancer risk in a rat skin model, and confounding factors. Summary conclusions are provided at the end of the report.

Towards short wavelengths FELs workshop

International Nuclear Information System (INIS)

Ben-Zvi, I.; Winick, H.

1993-01-01

This workshop was caged because of the growing perception in the FEL source community that recent advances have made it possible to extend FEL operation to wavelengths about two orders of magnitude shorter than the 240 nm that has been achieved to date. In addition short wavelength FELs offer the possibilities of extremely high peak power (several gigawatts) and very short pulses (of the order of 100 fs). Several groups in the USA are developing plans for such short wavelength FEL facilities. However, reviewers of these plans have pointed out that it would be highly desirable to first carry out proof-of-principle experiments at longer wavelengths to increase confidence that the shorter wavelength devices will indeed perform as calculated. The need for such experiments has now been broadly accepted by the FEL community. Such experiments were the main focus of this workshop as described in the following objectives distributed to attendees: (1) Define measurements needed to gain confidence that short wavelength FELs will perform as calculated. (2) List possible hardware that could be used to carry out these measurements in the near term. (3) Define a prioritized FEL physics experimental program and suggested timetable. (4) Form collaborative teams to carry out this program

Towards short wavelengths FELs workshop

Science.gov (United States)

Ben-Zvi, I.; Winick, H.

1993-11-01

This workshop was caged because of the growing perception in the FEL source community that recent advances have made it possible to extend FEL operation to wavelengths about two orders of magnitude shorter than the 240 nm that has been achieved to date. In addition short wavelength FEL's offer the possibilities of extremely high peak power (several gigawatts) and very short pulses (of the order of 100 fs). Several groups in the USA are developing plans for such short wavelength FEL facilities. However, reviewers of these plans have pointed out that it would be highly desirable to first carry out proof-of-principle experiments at longer wavelengths to increase confidence that the shorter wavelength devices will indeed perform as calculated. The need for such experiments has now been broadly accepted by the FEL community. Such experiments were the main focus of this workshop as described in the following objectives distributed to attendees: (1) Define measurements needed to gain confidence that short wavelength FEL's will perform as calculated. (2) List possible hardware that could be used to carry out these measurements in the near term. (3) Define a prioritized FEL physics experimental program and suggested timetable. (4) Form collaborative teams to carry out this program.

Optimizing Dam Operations for Power and for Fish: an Overview of the US Department of Energy and US Army Corps of Engineers ADvanced Turbine Development R&D. A Pre-Conference Workshop at HydroVision 2006, Oregon Convention Center, Portland, Oregon July 31, 2006

Energy Technology Data Exchange (ETDEWEB)

Dauble, Dennis D.

2006-08-01

This booklet contains abstracts of presentations made at a preconference workshop on the US Department of Energy and US Army Corps of Engineers hydroturbine programs. The workshop was held in conjunction with Hydrovision 2006 July 31, 2006 at the Oregon Convention Center in Portland Oregon. The workshop was organized by the Corps of Engineers, PNNL, and the DOE Wind and Hydropower Program. Presenters gave overviews of the Corps' Turbine Survival Program and the history of the DOE Advanced Turbine Development Program. They also spoke on physical hydraulic models, biocriteria for safe fish passage, pressure investigations using the Sensor Fish Device, blade strike models, optimization of power plant operations, bioindex testing of turbine performance, approaches to measuring fish survival, a systems view of turbine performance, and the Turbine Survival Program design approach.

Advanced seismic imaging for geothermal development

Energy Technology Data Exchange (ETDEWEB)

Louie, John [UNR; Pullammanappallil, Satish [Optim; Honjas, Bill [Optim

2016-08-01

J. N. Louie, Pullammanappallil, S., and Honjas, W., 2011, Advanced seismic imaging for geothermal development: Proceedings of the New Zealand Geothermal Workshop 2011, Nov. 21-23, Auckland, paper 32, 7 pp. Preprint available at http://crack.seismo.unr.edu/geothermal/Louie-NZGW11.pdf

FOREWORD: 5th International Workshop on New Computational Methods for Inverse Problems

Science.gov (United States)

Vourc'h, Eric; Rodet, Thomas

2015-11-01

This volume of Journal of Physics: Conference Series is dedicated to the scientific research presented during the 5th International Workshop on New Computational Methods for Inverse Problems, NCMIP 2015 (http://complement.farman.ens-cachan.fr/NCMIP_2015.html). This workshop took place at Ecole Normale Supérieure de Cachan, on May 29, 2015. The prior editions of NCMIP also took place in Cachan, France, firstly within the scope of ValueTools Conference, in May 2011, and secondly at the initiative of Institut Farman, in May 2012, May 2013 and May 2014. The New Computational Methods for Inverse Problems (NCMIP) workshop focused on recent advances in the resolution of inverse problems. Indeed, inverse problems appear in numerous scientific areas such as geophysics, biological and medical imaging, material and structure characterization, electrical, mechanical and civil engineering, and finances. The resolution of inverse problems consists of estimating the parameters of the observed system or structure from data collected by an instrumental sensing or imaging device. Its success firstly requires the collection of relevant observation data. It also requires accurate models describing the physical interactions between the instrumental device and the observed system, as well as the intrinsic properties of the solution itself. Finally, it requires the design of robust, accurate and efficient inversion algorithms. Advanced sensor arrays and imaging devices provide high rate and high volume data; in this context, the efficient resolution of the inverse problem requires the joint development of new models and inversion methods, taking computational and implementation aspects into account. During this one-day workshop, researchers had the opportunity to bring to light and share new techniques and results in the field of inverse problems. The topics of the workshop were: algorithms and computational aspects of inversion, Bayesian estimation, Kernel methods, learning methods

Tenth Workshop on Crystalline Silicon Solar Cell Materials and Processes: A Summary of Discussion Sessions

Energy Technology Data Exchange (ETDEWEB)

Tan, T.; Swanson, D.; Sinton, R.; Sopori, B.

2001-01-22

The 10th Workshop on Silicon Solar Cell Materials and Processes was held in Copper Mountain, Colorado, on August 13-16, 2000. The workshop was attended by 85 scientists and engineers from 15 international photovoltaic (PV) companies and 24 research institutions. Review and poster presentations were augmented by discussion sessions to address the recent progress and critical issues in meeting the goals for Si in the PV Industry Roadmap. The theme of the workshop was Si Photovoltaics: 10 Years of Progress and Opportunities for the Future. Two special sessions were held: Advanced Metallization and Interconnections - covering recent advances in solar cell metallization, printed contacts and interconnections, and addressing new metallization schemes for low-cost cell interconnections; and Characterization Methods - addressing the growing need for process monitoring techniques in the PV industry. The following major issues emerged from the discussion sessions: (1) Mechanical breakage in the P V industry involves a large fraction, about 5%-10%, of the wafers. (2) The current use of Al screen-printed back-contacts appears to be incompatible with the PV Industry Roadmap requirements. (3) The PV manufacturers who use hydrogen passivation should incorporate the plasma-enhanced chemical vapor deposited (PECVD) nitride for antireflection coating and hydrogenation. (4) There is an imminent need to dissolve metallic precipitates to minimize the electrical shunt problem caused by the ''bad'' regions in wafers. (5) Industry needs equipment for automated, in-line monitoring and testing. There are simply not many tools available to industry. (6) In the Wrap-Up Session of the workshop, there was consensus to create four industry/university teams that would address critical research topics in crystalline silicon. (7) The workshop attendees unanimously agreed that the workshop has served well the PV community by promoting the fundamental understanding of industrial

2014 Penn State Bioinorganic Workshop

Energy Technology Data Exchange (ETDEWEB)

Golbeck, John [Pennsylvania State Univ., State College, PA (United States)

2015-10-01

The 3rd Penn State Bioinorganic Workshop took place in early June 2014 and was combined with the 3rd Penn State Frontiers in Metallobiochemistry Symposium. The workshop was even larger than the 2nd Penn State Bioinorganic Workshop we offered in 2012. It had even more participants (162 rather than 123 in 2012). Like the 2012 workshop, the 2014 workshop had three parts. The first part consisted of 16 90-minute lectures presented by faculty experts on the topic of their expertise (see below). Based on the suggestions from the 2012 workshop, we have recorded all 16 lectures professionally and make them available to the entire bioinorganic community via online streaming. In addition, hard copies of the recordings are available as backup.

INDICO Workshop

CERN Multimedia

CERN. Geneva; Fabbrichesi, Marco

2004-01-01

The INtegrated DIgital COnferencing EU project has finished building a complete software solution to facilitate the MANAGEMENT OF CONFERENCES, workshops, schools or simple meetings from their announcement to their archival. Everybody involved in the organization of events is welcome to join this workshop, in order to understand the scope of the project and to see demonstrations of the various features.

PREFACE: 16th European White Dwarfs Workshop

Science.gov (United States)

Garcia-Berro, Enrique; Hernanz, Margarita; Isern, Jordi; Torres, Santiago

2009-07-01

The 16th European Workshop on White Dwarfs was held in Barcelona, Spain, from 30 June to 4 July 2008 at the premises of the UPC. Almost 120 participants from Europe (France, Germany, United Kingdom, Italy, and several others), America (USA, Canada, Argentina, Brazil, and Chile), and other continents (Australia, South Africa, . . . ) attended the workshop. Among these participants were the most relevant specialists in the field. The topics covered by the conference were: White dwarf structure and evolution Progenitors and Planetary Nebulae White dwarfs in binaries: cataclysmic variables, double degenerates and other binaries White dwarfs, dust disks and planetary systems Atmospheres, chemical composition, magnetic fields Variable white dwarfs White dwarfs in stellar clusters and the halo White Dwarfs as SNIa progenitors The programme included 54 talks, and 45 posters. The oral presentations were distributed into the following sessions: Luminosity function, mass function and populations White dwarf structure and evolution White dwarf ages White dwarf catalogs and surveys Central stars of planetary nebulae Supernovae progenitors White dwarfs in novae and CVs Physical processes in white dwarfs and magnetic white dwarfs Disks, dust and planets around white dwarfs Pulsating white dwarfs Additionally we had a special open session about Spitzer and white dwarfs. The Proceedings of the 16th European Workshop on White Dwarfs are representative of the current state-of-the-art of the research field and include new and exciting results. We acknowledge the very positive attitude of the attendants to the workshop, which stimulated very fruitful discussions that took place in all the sessions and after the official schedule. Also, the meeting allowed new collaborations tp start that will undoubtedly result in significant advances in the research field. We also acknowledge the willingness of the participants to deliver their contributions before the final deadline. We sincerely

Proceedings of workshop on K-decay experiments

International Nuclear Information System (INIS)

Nakai, Kozi

1989-08-01

The elementary particle experiment using the 12 GeV proton synchrotron in the National Laboratory for High Energy Physics (KEK) develops centering around the large scale experiment on K-meson decay. In this case, the ideal precision physics is pursued, and efforts have been exerted to improve the experimental techniques. At present the experiment on searching for rare K-decay is advancing. Next, the experiment on searching for CP nonconservation process will be begun. However, these experiments are in severe competition with those in BNL and Fermilab which have powerful accelerators, therefore it is desirable to grasp well the development of the international research plans. Therefore, in order to obtain the quideline for the experimental plan using the KEK proton synchrotron hereafter, the workshop on K-decay was held on July 11∼12, 1989. In this workshop, Arisaka (UCLA), Numao (TRIUMF) and Yamanaka (Fermilab) returned from USA and lectured on the present status of the experiment and the future perspective. The impression of the planner of the proton synchrotron experiment plan on the experiments are recorded. (K.I.)

Summer of Seasons Workshop Program for Emerging Educators in Earth System Science

Science.gov (United States)

Chaudhury, S. Raj

2002-01-01

Norfolk State University BEST Lab successfully hosted three Summer of Seasons programs from 1998-2001. The Summer of Seasons program combined activities during the summer with additional seminars and workshops to provide broad outreach in the number of students and teachers who participated. Lessons learned from the each of the first two years of this project were incorporated into the design of the final year's activities. The "Summer of Seasons" workshop program provided emerging educators with the familiarity and knowledge to utilize in the classroom curriculum materials developed through NASA sponsorship on Earth System Science. A special emphasis was placed on the use of advanced technologies to dispel the commonly held misconceptions regarding seasonal, climactic and global change phenomena.

Annual Anastasia Arbovirus Surveillance and Mosquito Control Workshops: Summary of the Past 11 Years

Science.gov (United States)

Realizing the needs of local mosquito control workers for advance training and education the Anastasia Mosquito Control District (AMCD) and the USDA-ARS Center for Medical, Agricultural and Veterinary entomology (CMAVE) developed a regional workshop to address these needs. Since 2004 the AMCD and CM...

32 CFR 700.846 - Status of logs.

Science.gov (United States)

2010-07-01

... Officers Afloat § 700.846 Status of logs. The deck log, the engineering log, the compass record, the bearing hooks, the engineer's bell book, and any records generated by automated data logging equipment...

Empirical relationships between tree fall and landscape-level amounts of logging and fire.

Science.gov (United States)

Lindenmayer, David B; Blanchard, Wade; Blair, David; McBurney, Lachlan; Stein, John; Banks, Sam C

2018-01-01

Large old trees are critically important keystone structures in forest ecosystems globally. Populations of these trees are also in rapid decline in many forest ecosystems, making it important to quantify the factors that influence their dynamics at different spatial scales. Large old trees often occur in forest landscapes also subject to fire and logging. However, the effects on the risk of collapse of large old trees of the amount of logging and fire in the surrounding landscape are not well understood. Using an 18-year study in the Mountain Ash (Eucalyptus regnans) forests of the Central Highlands of Victoria, we quantify relationships between the probability of collapse of large old hollow-bearing trees at a site and the amount of logging and the amount of fire in the surrounding landscape. We found the probability of collapse increased with an increasing amount of logged forest in the surrounding landscape. It also increased with a greater amount of burned area in the surrounding landscape, particularly for trees in highly advanced stages of decay. The most likely explanation for elevated tree fall with an increasing amount of logged or burned areas in the surrounding landscape is change in wind movement patterns associated with cutblocks or burned areas. Previous studies show that large old hollow-bearing trees are already at high risk of collapse in our study area. New analyses presented here indicate that additional logging operations in the surrounding landscape will further elevate that risk. Current logging prescriptions require the protection of large old hollow-bearing trees on cutblocks. We suggest that efforts to reduce the probability of collapse of large old hollow-bearing trees on unlogged sites will demand careful landscape planning to limit the amount of timber harvesting in the surrounding landscape.

The QED Workshop

Energy Technology Data Exchange (ETDEWEB)

Pieper, G.W.

1994-07-01

On May 18--20, 1994, Argonne National Laboratory hosted the QED Workshop. The workshop was supported by special funding from the Office of Naval Research. The purpose of the workshop was to assemble of a group of researchers to consider whether it is desirable and feasible to build a proof-checked encyclopedia of mathematics, with an associated facility for theorem proving and proof checking. Among the projects represented were Coq, Eves, HOL, ILF, Imps, MathPert, Mizar, NQTHM, NuPrl, OTTER, Proof Pad, Qu-Prolog, and RRL. Although the content of the QED project is highly technical rigorously proof-checked mathematics of all sorts the discussions at the workshop were rarely technical. No prepared talks or papers were given. Instead, the discussions focused primarily on such political, sociological, practical, and aesthetic questions, such as Why do it? Who are the customers? How can one get mathematicians interested? What sort of interfaces are desirable? The most important conclusion of the workshop was that QED is an idea worthy pursuing, a statement with which virtually all the participants agreed. In this document, the authors capture some of the discussions and outline suggestions for the start of a QED scientific community.

TANGR2015 Heidelberg. Second international workshop on tracer applications of noble gas radionuclides in the geosciences

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-07-01

TANGR2015 is a workshop on the progress in the technique and application of Atom Trap Trace Analyis (ATTA). It is a follow-up to the first TANGR workshop, TANGR2012, which was held at the Argonne National Laboratory, Argonne, USA, in June 2012. It is organized in response to recent technical advances and new applications of Atom Trap Trace Analysis (ATTA), an analytical method for measuring the isotopes {sup 81}Kr, {sup 85}Kr, and {sup 39}Ar. The primary aim of the workshop is to discuss the technical progress of ATTA and thereby enable innovative and timely applications of the noble gas radionuclides to important scientific problems in earth and environmental sciences, e.g. in the fields of groundwater hydrology, glaciology, oceanography, and paleoclimatology.

Exascale Workshop Panel Report Meeting

Energy Technology Data Exchange (ETDEWEB)

Khaleel, Mohammad A.

2010-07-01

The Exascale Review Panel consists of 12 scientists and engineers with experience in various aspects of high-performance computing and its application, development, and management. The Panel hear presentations by several representatives of the workshops and town meetings convened over the past few years to examine the need for exascale computation capability and the justification for a U.S. Department of Energy (DOE) program to develop such capability. This report summarizes information provided by the presenters and substantial written reports to the Panel in advance of the meeting in Washington D.C. on January 19-20, 2010. The report also summarizes the Panel's conclusions with regard to the justification of a DOE-led exascale initiative.

11th Workshop on Crystalline Silicon Solar Cell Materials and Processes, Extended Abstracts and Papers, 19-22 August 2001, Estes Park, Colorado

Energy Technology Data Exchange (ETDEWEB)

Sopori, B.

2001-08-16

The 11th Workshop will provide a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and non-photovoltaic fields. Discussions will include the various aspects of impurities and defects in silicon--their properties, the dynamics during device processing, and their application for developing low-cost processes for manufacturing high-efficiency silicon solar cells. Sessions and panel discussions will review impurities and defects in crystalline-silicon PV, advanced cell structures, new processes and process characterization techniques, and future manufacturing demands. The workshop will emphasize some of the promising new technologies in Si solar cell fabrication that can lower PV energy costs and meet the throughput demands of the future. The three-day workshop will consist of presentations by invited speakers, followed by discussion sessions. Topics to be discussed are: Si Mechanical properties and Wafer Handling, Advanced Topics in PV Fundamentals, Gettering and Passivation, Impurities and Defects, Advanced Emitters, Crystalline Silicon Growth, and Solar Cell Processing. The workshop will also include presentations by NREL subcontractors who will review the highlights of their research during the current subcontract period. In addition, there will be two poster sessions presenting the latest research and development results. Some presentations will address recent technologies in the microelectronics field that may have a direct bearing on PV.

Palm distributions for log Gaussian Cox processes

DEFF Research Database (Denmark)

Coeurjolly, Jean-Francois; Møller, Jesper; Waagepetersen, Rasmus Plenge

2017-01-01

This paper establishes a remarkable result regarding Palm distributions for a log Gaussian Cox process: the reduced Palm distribution for a log Gaussian Cox process is itself a log Gaussian Cox process that only differs from the original log Gaussian Cox process in the intensity function. This new...... result is used to study functional summaries for log Gaussian Cox processes....

Summary of EC-17: the 17th Joint Workshop on Electron Cyclotron Emission and Electron Cyclotron Resonance Heating (Deurne, The Netherlands, 7-10 May 2012)

NARCIS (Netherlands)

Westerhof, E.; Austin, M. E.; Kubo, S.; Lin-Liu, Y. R.; Plaum, B.

2013-01-01

An overview is given of the papers presented at the 17th Joint Workshop on Electron Cyclotron Emission (ECE) and Electron Cyclotron Resonance Heating (ECRH). The meeting covered all aspects of the research field ranging from theory to enabling technologies. From the workshop, advanced control by

ADVANCED GAS TURBINE SYSTEMS RESEARCH

Energy Technology Data Exchange (ETDEWEB)

Unknown

2002-04-01

The activities of the Advanced Gas Turbine Systems Research (AGTSR) program for this reporting period are described in this quarterly report. The report is divided into discussions of Membership, Administration, Technology Transfer (Workshop/Education), Research and Miscellaneous Related Activity. Items worthy of note are presented in extended bullet format following the appropriate heading.

ADVANCED GAS TURBINE SYSTEMS RESEARCH

Energy Technology Data Exchange (ETDEWEB)

Unknown

2002-02-01

The activities of the Advanced Gas Turbine Systems Research (AGTSR) program for this reporting period are described in this quarterly report. The report is divided into discussions of Membership, Administration, Technology Transfer (Workshop/Education), Research and Miscellaneous Related Activity. Items worthy of note are presented in extended bullet format following the appropriate heading.

Systematic logging utilizing a log sheet designed for drill core descriptions. An example in uranium exploration activities

International Nuclear Information System (INIS)

Sasao, Eiji; Tsuruta, Tadahiko; Iida, Yoshimasa

2000-01-01

We describe the log sheets used during uranium exploration activities for unconformity-related uranium deposits by JNC. The purpose of using the logging sheets is to standardize the objects which all geologists must observe and for data quality assurance. The log sheets are a three-part set describing basement lithology, sandstone lithology and geotechnics. We devised our own log sheets to describe both the sandstone and the underlying basement rock when we started exploration in Athabasca Basin, Canada. We modified the sheets to gain a better understanding of the geological features related to uranium mineralization, and made final improvements to satisfy required quality based on the criteria of descriptive objects and accuracy. Use of the log sheets resulted in effective performance of core logging and improvement in the display of data. (author)

Log-binomial models: exploring failed convergence.

Science.gov (United States)

Williamson, Tyler; Eliasziw, Misha; Fick, Gordon Hilton

2013-12-13

Relative risk is a summary metric that is commonly used in epidemiological investigations. Increasingly, epidemiologists are using log-binomial models to study the impact of a set of predictor variables on a single binary outcome, as they naturally offer relative risks. However, standard statistical software may report failed convergence when attempting to fit log-binomial models in certain settings. The methods that have been proposed in the literature for dealing with failed convergence use approximate solutions to avoid the issue. This research looks directly at the log-likelihood function for the simplest log-binomial model where failed convergence has been observed, a model with a single linear predictor with three levels. The possible causes of failed convergence are explored and potential solutions are presented for some cases. Among the principal causes is a failure of the fitting algorithm to converge despite the log-likelihood function having a single finite maximum. Despite these limitations, log-binomial models are a viable option for epidemiologists wishing to describe the relationship between a set of predictors and a binary outcome where relative risk is the desired summary measure. Epidemiologists are encouraged to continue to use log-binomial models and advocate for improvements to the fitting algorithms to promote the widespread use of log-binomial models.

NNSA / IAEA VVER reactor safety workshops. May 2002 - April 2003. Executive summary

International Nuclear Information System (INIS)

Evans, M.; Petri, M. C.

2003-01-01

Over the past year, the U.S. National Nuclear Security Administration (NNSA) has sponsored four workshops to compare the probabilistic risk assessments (PRAs) of Soviet-designed VVER power plants. The ''International Workshop on Safety of First-Generation VVER-440 Nuclear Power Plants'' was held on May 20-25, 2002, in Piestany, Slovakia. A short follow-on workshop was held in Bratislava, Slovakia, on November 5-6, 2002, to complete the work begun in May. Piestany was the location also for the ''International Workshop on Safety of Second-Generation VVER-440 Nuclear Power Plants'' (September 9-14, 2002) and the ''International Workshop on Safety of VVER-1000 Nuclear Power Plants'' (April 7-12, 2003). The four workshops were held in cooperation with the International Atomic Energy Agency (IAEA), the Nuclear Regulatory Authority of Slovakia (UJD), the Center for Nuclear Safety in Central and Eastern Europe (CENS), and Argonne National Laboratory (ANL). The objectives of the workshops were to identify the impact of the improvements on the core damage frequency; the contribution to the PRA results of different assumptions about events that can occur at the plants; and to understand, identify, and prioritize potential improvements in hardware and plant operation of VVER nuclear power plants. These objectives were achieved based on insights gained from recent PRAs completed by the plants and their technical support organizations. Nine first-generation VVER-440 plants (nominally of the VVER-440/230 design) are currently operating in Armenia, Bulgaria, Russia, and Slovakia. Sixteen VVER-440/213 plants are currently operating in the Czech Republic, Hungary, Russia, Slovakia, and Ukraine. Twenty-three VVER-1000 plants are currently operating in Bulgaria, the Czech Republic, Russia, and Ukraine. Eleven addition plants are in the advanced stages of construction in various parts of the world. The workshops reviewed the current configuration and safety status of each plant

Diversifying Geoscience by Preparing Faculty as Workshop Leaders to Promote Inclusive Teaching and Inclusive Geoscience Departments

Science.gov (United States)

Macdonald, H.; Manduca, C. A.; Beane, R. J.; Doser, D. I.; Ebanks, S. C.; Hodder, J.; McDaris, J. R.; Ormand, C. J.

2017-12-01

Efforts to broaden participation in the geosciences require that faculty implement inclusive practices in their teaching and their departments. Two national projects are building the capacity for faculty and departments to implement inclusive practices. The NAGT/InTeGrate Traveling Workshops Program (TWP) and the Supporting and Advancing Geoscience Education in Two-Year Colleges (SAGE 2YC) project each prepares a cadre of geoscience educators to lead workshops that provide opportunities for faculty and departments across the country to enhance their abilities to implement inclusive teaching practices and develop inclusive environments with the goal of increasing diversity in the geosciences. Both projects prepare faculty to design and lead interactive workshops that build on the research base, emphasize practical applications and strategies, enable participants to share their knowledge and experience, and include time for reflection and action planning. The curriculum common to both projects includes a framework of support for the whole student, supporting all students, data on diversity in the geosciences, and evidence-based strategies for inclusive teaching and developing inclusive environments that faculty and departments can implement. Other workshop topics include classroom strategies for engaging all students, addressing implicit bias and stereotype threat, and attracting diverse students to departments or programs and helping them thrive. Online resources for each project provide support beyond the workshops. The TWP brings together educators from different institutional types and experiences to develop materials and design a workshop offered to departments and organizations nationwide that request the workshop; the workshop leaders then customize the workshop for that audience. In SAGE 2YC, a team of leaders used relevant literature to develop workshop materials intended for re-use, and designed a workshop session for SAGE 2YC Faculty Change Agents, who

76 FR 55837 - Workshops To Discuss Revisions to Federal and Indian Coal Valuation Regulations: Advance Notice...

Science.gov (United States)

2011-09-09

...-3585. Workshop 2--Marriott St. Louis Airport, 10700 Pear Tree Lane, St. Louis, Missouri 63134..., each person may be required to present a picture identification to gain entry to the meetings. Dated...

Comparative analysis of nuclear magnetic resonance well logging and nuclear magnetic resonance mud logging

International Nuclear Information System (INIS)

Yuan Zugui

2008-01-01

The hydrogen atoms in oil and water are able to resonate and generate signals in the magnetic field, which is used by the NMR (nuclear magnetic resonance) technology in petroleum engineering to research and evaluate rock characteristics. NMR well logging was used to measure the physical property parameters of the strata in well bore, whereas NMR mud logging was used to analyze (while drilling) the physical property parameters of cores, cuttings and sidewall coring samples on surface (drilling site). Based on the comparative analysis of the porosity and permeability parameters obtained by NMR well logging and those from analysis of the cores, cuttings and sidewall coring samples by NMR mud logging in the same depth of 13 wells, these two methods are of certain difference, but their integral tendency is relatively good. (authors)

DOE-Grand Junction logging model data synopsis

International Nuclear Information System (INIS)

Mathews, M.A.; Koizumi, C.J.; Evans, H.B.

1978-05-01

This synopsis provides the available data concerning the logging models at the DoE-Grand Junction facility, to date (1976). Because gamma-ray logs are used in uranium exploration to estimate the grade (percent U 3 O 8 ) and the thickness of uranium ore zones in exploration drill holes, logging models are required to calibrate the gamma-ray logging equipment in order to obtain accuracy, uniformity, standardization, and repeatability during logging. This quality control is essential for accurate ore reserve calculations and for estimates of ore potential. The logging models at the DoE-Grand Junction facility are available for use by private industry in calibrating their gamma-ray logging equipment. 21 figures, 26 tables

SNG-logs at Skjern

DEFF Research Database (Denmark)

Korsbech, Uffe C C; Petersen, Jesper; Aage, Helle Karina

1998-01-01

Spectral Natural Gamma-ray logs have been run in two water supply borings at Skjern. The log data have been examined by a new technique - Noise Adjusted Singular Value Decomposition - in order to get a detailed and reliable picture of the distribution of uranium and thorium gamma-rays from heavy...

Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement: Advancing Risk Analysis for Nanoscale Materials

Energy Technology Data Exchange (ETDEWEB)

Shatkin, J. A. [Vireo Advisors, Boston MA USA; Ong, Kimberly J. [Vireo Advisors, Boston MA USA; Beaudrie, Christian [Compass RM, Vancouver CA USA; Clippinger, Amy J. [PETA International Science Consortium Ltd, London UK; Hendren, Christine Ogilvie [Center for the Environmental Implications of NanoTechnology, Duke University, Durham NC USA; Haber, Lynne T. [TERA, Cincinnati OH USA; Hill, Myriam [Health Canada, Ottawa Canada; Holden, Patricia [UC Santa Barbara, Bren School of Environmental Science & Management, ERI, and UC CEIN, University of California, Santa Barbara CA USA; Kennedy, Alan J. [U.S. Army Engineer Research and Development Center, Environmental Laboratory, Vicksburg MS USA; Kim, Baram [Independent, Somerville MA USA; MacDonell, Margaret [Argonne National Laboratory, Environmental Science Division, Argonne IL USA; Powers, Christina M. [U.S. Environmental Protection Agency, Office of Air and Radiation, Office of Transportation and Air Quality, Ann Arbor MI USA; Sharma, Monita [PETA International Science Consortium Ltd, London UK; Sheremeta, Lorraine [Alberta Ingenuity Labs, Edmonton Alberta Canada; Stone, Vicki [John Muir Building Gait 1 Heriot-Watt University, Edinburgh Scotland UK; Sultan, Yasir [Environment Canada, Gatineau QC Canada; Turley, Audrey [ICF International, Durham NC USA; White, Ronald H. [RH White Consultants, Silver Spring MD USA

2016-08-01

The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article.

Advanced digital computers, controls, and automation technologies for power plants: Proceedings

International Nuclear Information System (INIS)

Bhatt, S.C.

1992-08-01

This document is a compilation of the papers that were presented at an EPRI workshop on Advances in Computers, Controls, and Automation Technologies for Power Plants. The workshop, sponsored by EPRI's Nuclear Power Division, took place February 1992. It was attended by 157 representatives from electric utilities, equipment manufacturers, engineering consulting organizations, universities, national laboratories, government agencies and international utilities. More than 40% of the attendees were from utilities representing the majority group. There were 30% attendees from equipment manufacturers and the engineering consulting organizations. The participants from government agencies, universities, and national laboratories were about 10% each. The workshop included a keynote address, 35 technical papers, and vendor's equipment demonstrations. The technical papers described the state-of-the-art in the areas of recent utility digital upgrades such as digital feedwater controllers, steam generator level controllers, integrated plant computer systems, computer aided diagnostics, automated testing and surveillance and other applications. A group of technical papers presented the ongoing B ampersand W PWR integrated plant control system prototype developments with the triple redundant advanced digital control system. Several international papers from France, Japan and U.K. presented their programs on advance power plant design and applications. Significant advances in the control and automation technologies such as adaptive controls, self-tuning methods, neural networks and expert systems were presented by developers, universities, and national laboratories. Individual papers are indexed separately

Influence of borehole-eccentred tools on wireline and logging-while-drilling sonic logging measurements

KAUST Repository

Pardo, David; Matuszyk, Paweł Jerzy; Torres-Verdí n, Carlos; Mora Cordova, Angel; Muga, Ignacio; Calo, Victor M.

2013-01-01

We describe a numerical study to quantify the influence of tool-eccentricity on wireline (WL) and logging-while-drilling (LWD) sonic logging measurements. Simulations are performed with a height-polynomial-adaptive (hp) Fourier finite-element method

The Third ATLAS ROD Workshop

CERN Multimedia

Poggioli, L.

A new-style Workshop After two successful ATLAS ROD Workshops dedicated to the ROD hardware and held at the Geneva University in 1998 and in 2000, a new style Workshop took place at LAPP in Annecy on November 14-15, 2002. This time the Workshop was fully dedicated to the ROD-TDAQ integration and software in view of the near future integration activities of the final RODs for the detector assembly and commissioning. More precisely, the aim of this workshop was to get from the sub-detectors the parameters needed for T-DAQ, as well as status and plans from ROD builders. On the other hand, what was decided and assumed had to be stated (like EB decisions and URDs), and also support plans. The Workshop gathered about 70 participants from all ATLAS sub-detectors and the T-DAQ community. The quite dense agenda allowed nevertheless for many lively discussions, and for a dinner in the old town of Annecy. The Sessions The Workshop was organized in five main sessions: Assumptions and recommendations Sub-de...

Externally predictive single-descriptor based QSPRs for physico-chemical properties of polychlorinated-naphthalenes: Exploring relationships of log S{sub W}, log K{sub OA}, and log K{sub OW} with electron-correlation

Energy Technology Data Exchange (ETDEWEB)

Chayawan; Vikas, E-mail: qlabspu@pu.ac.in

2015-10-15

Highlights: • Aqueous solubility and partition coefficient are modelled using single-parameter. • Electron-correlation observed as a vital predictorof physico-chemical properties. • For octanol-air partition coefficient, energy and polarizability yield best models. • Dipole-moment is found to be worst single-descriptor for the properties analysed. - Abstract: Quantitative structure–property relationships (QSPRs), based only on a single-parameter, are proposed for the prediction of physico-chemical properties, namely, aqueous solubility (log S{sub W}), octanol–water partition coefficient (log K{sub OW}) and octanol–air partition coefficient (log K{sub OA}) of polychloronaphthalenes (PCNs) including all the 75 chloronaphthalene congeners. The QSPR models are developed using molecular descriptors computed through quantum mechanical methods including ab-initio as well as advanced semi-empirical methods. The predictivity of the developed models is tested through state-of-the-art external validation procedures employing an external prediction set of compounds. To analyse the role of instantaneous interactions between electrons (the electron-correlation), the models are also compared with those developed using only the electron-correlation contribution of the quantum chemical descriptor. The electron-correlation contribution towards the chemical hardness and the LUMO energy are observed to be the best predictors for octanol–water partition coefficient, whereas for the octanol–air partition coefficient, the total electronic energy and electron-correlation energy are found to be reliable descriptors, in fact, even better than the polarisability. For aqueous solubility of PCNs, the absolute electronegativity is observed to be the best predictor. This work suggests that the electron-correlation contribution of a quantum-chemical descriptor can be used as a reliable indicator for physico-chemical properties, particularly the partition coefficients.

Workshop Papers: Directions and Marketing of Synthetic Crude Oil and Heavy Oil

International Nuclear Information System (INIS)

1997-01-01

This workshop was organized by the National Centre for Upgrading Technology in an effort to bring together experts from the various sectors of the petroleum industry to outline their views of the directions that the synthetic crude oil market will pursue over the next decade and into the 21. century. The motivation for the Workshop came from the many announcements during 1996 and 1997 by several Canadian oil companies about plans to initiate or expand their heavy oil and synthetic crude production. During the same period, at least one US refiner also announced plans to revamp an existing refinery to allow it to process Canadian heavy oil and synthetic crude. The workshop was organized to review these plans and to discuss such questions as (1) Would the selected technologies be the familiar carbon rejection or hydrogen addition methods, or would there be radical advanced technologies? (2) Would the products be fully or partially upgraded? (3) How would they be processed in the refinery? (4) Would there be a market? This collection of papers or viewgraphs comprise all the formal presentations given at the workshop. The final section also contains the edited notes recorded during the question and answer periods. refs., tabs., figs

Proceedings of the workshop on opportunities for atomic physics using slow, highly-charged ions

International Nuclear Information System (INIS)

1987-01-01

The study of atomic physics with highly-charged ions is an area of intense activity at the present time because of a convergence of theoretical interest and advances in experimental techniques. The purpose of the Argonne ''Workshop on Opportunities for Atomic Physics Using Slow, Highly-Charged Ions'' was to bring together atomic, nuclear, and accelerator physicists in order to identify what new facilities would be most useful for the atomic physics community. The program included discussion of existing once-through machines, advanced ion sources, recoil ion techniques, ion traps, and cooler rings. One of the topics of the Workshop was to discuss possible improvement to the ANL Tandem-Linac facility (ATLAS) to enhance the capability for slowing down ions after they are stripped to a high-charge state (the Accel/Decel technique). Another topic was the opportunity for atomic physics provided by the ECR ion source which is being built for the Uranium Upgrade of ATLAS. 18 analytics were prepared for the individual papers in this volume

Leadership Workshops for Adult Girl Scout Leaders

Science.gov (United States)

Lebofsky, Larry A.; McCarthy, Donald; DeVore, Edna; Harman, Pamela; Reaching Stars Team

2016-10-01

This year, the University of Arizona is conducting its first two Leadership Workshops for Girl Scout adult leaders. These workshops are being supported by a five-year NASA Collaborative Agreement, Reaching for the Stars: NASA Science for Girl Scouts (www.seti.org/GirlScoutStars), through the SETI Institute in collaboration with the University of Arizona, Girl Scouts of the USA (GSUSA), the Girl Scouts of Northern California, the Astronomical Society of the Pacific, and Aries Scientific, Inc. These workshops are an outgrowth of Astronomy Camp for Girl Scout Leaders, a 14-year "Train the Trainer" program funded by NASA through the James Webb Space Telescope's Near Infrared Camera (NIRCam) education and outreach team. We are continuing our long-term relationship with all Girl Scout Councils to engage girls and young women not only in science and math education, but also in the astronomical and technological concepts relating to NASA's scientific mission. Our training aligns with the GSUSA Journey: It's Your Planet-Love It! and introduces participants to some of the activities that are being developed by the Girl Scout Stars team for GSUSA's new space science badges for all Girl Scout levels being developed as a part of Reaching for the Stars: NASA Science for Girl Scouts.The workshops include hands-on activities in basic astronomy (night sky, stars, galaxies, optics, telescopes, etc.) as well as some more advanced concepts such as lookback time and the expansion of the Universe. Since the inception of our original Astronomy Camp in 2003, our team has grown to include nearly 280 adult leaders, staff, and volunteers from over 79 Councils in 43 states and the District of Columbia so they can, in turn, teach young women essential concepts in astronomy, the night sky environment, applied math, and engineering. Our workshops model what astronomers do by engaging participants in the process of science inquiry, while equipping adults to host astronomy-related programs with

Emergency response workers workshop

International Nuclear Information System (INIS)

Agapeev, S.A.; Glukhikh, E.N.; Tyurin, R.L.

2012-01-01

A training workshop entitled Current issues and potential improvements in Rosatom Corporation emergency prevention and response system was held in May-June, 2012. The workshop combined theoretical training with full-scale practical exercise that demonstrated the existing innovative capabilities for radiation reconnaissance, diving equipment and robotics, aircraft, emergency response and rescue hardware and machinery. This paper describes the activities carried out during the workshop [ru

Spanish Government delegation in the ISR workshop clean room

CERN Multimedia

CERN PhotoLab

1982-01-01

A Spanish Government delegation visited CERN before Spain rejoined CERN as a Member State(in 1983). Some delegates were particularly interested in advanced technologies. The picture shows them in the ISR workshop clean room looking at components of vacuum chambers for experiments. From left to right: a delegate, Director-General Herwig Schopper demonstrating the lightness of a titanium chamber, another delegate, the Spanish Minister of Industry and Energy Mr.Ignacio Bayon Marine and Romeo Perin. See also 8202369.

Nuclear well logging in hydrology

International Nuclear Information System (INIS)

1971-01-01

The optimum development of regional and local groundwater resources requires a quantitative evaluation of its aquifers and aquicludes, and of the physical and chemical properties relevant to the recharge to and withdrawal of water from them. If an understanding of the groundwater regime is to be obtained, geological observations at outcrop must be augmented by subsurface measurements of the strata and the waters they contain. Measurements of many hydrological and geological parameters can be made in situ by nuclear geophysical well-logging methods. Very simply, well logging consists of lowering a measuring probe into a well and making a continuous record of the variations of a particular parameter with depth. In most circumstances, repetition of the measurements under differing hydrodynamic conditions results in a better definition of the flow regime in the aquifer. Nuclear well-logging techniques have for some years been capable of solving a number of the sub-surface measurement problems faced by hydrogeologists. However, the present usage of these methods varies from country to country and the literature concerning applications is scattered in the professional journals of several disciplines. The objective of this report is to include in a single reference volume descriptions of the physical principles of nuclear logging methods, their applications to hydrogeological problems and their limitations on a level suitable for the practising hydrologists with a limited knowledge of nuclear physics. The Working Group responsible for compiling the report recommended that it should cover a broad spectrum of hydrogeological investigations and problems. For example, it saw no valid reason to distinguish for the purposes of the report between well-logging applications for water-supply purposes and for water-flooding studies in the petroleum industry. Neutron measurements made for soil-moisture determinations in the unsaturated zone have been specifically omitted, however, as

A Universal Logging System for LHCb Online

International Nuclear Information System (INIS)

Nikolaidis, Fotis; Brarda, Loic; Garnier, Jean-Christophe; Neufeld, Niko

2011-01-01

A log is recording of system's activity, aimed to help system administrator to traceback an attack, find the causes of a malfunction and generally with troubleshooting. The fact that logs are the only information an administrator may have for an incident, makes logging system a crucial part of an IT infrastructure. In large scale infrastructures, such as LHCb Online, where quite a few GB of logs are produced daily, it is impossible for a human to review all of these logs. Moreover, a great percentage of them as just n oise . That makes clear that a more automated and sophisticated approach is needed. In this paper, we present a low-cost centralized logging system which allow us to do in-depth analysis of every log.

Model wells for nuclear well logging

International Nuclear Information System (INIS)

Tittle, C.W.

1989-01-01

Considerations needed in the design and construction of model wells for nuclear log calibration are covered, with special attention to neutron porosity logging and total γ-ray logging. Pulsed neutron decay-time and spectral γ-ray logging are discussed briefly. The American Petroleum Institute calibration facility for nuclear logs is a good starting point for similar or expanded facilities. A few of its shortcomings are mentioned; they are minor. The problem of fluid saturation is emphasized. Attention is given to models made of consolidated rock and those containing unconsolidated material such as Ottawa sand. Needed precautions are listed. A similarity method is presented for estimating the porosity index of formations that are not fully saturated. (author)

Workshops of the Sixth International Brain–Computer Interface Meeting: brain–computer interfaces past, present, and future

Science.gov (United States)

Huggins, Jane E.; Guger, Christoph; Ziat, Mounia; Zander, Thorsten O.; Taylor, Denise; Tangermann, Michael; Soria-Frisch, Aureli; Simeral, John; Scherer, Reinhold; Rupp, Rüdiger; Ruffini, Giulio; Robinson, Douglas K. R.; Ramsey, Nick F.; Nijholt, Anton; Müller-Putz, Gernot; McFarland, Dennis J.; Mattia, Donatella; Lance, Brent J.; Kindermans, Pieter-Jan; Iturrate, Iñaki; Herff, Christian; Gupta, Disha; Do, An H.; Collinger, Jennifer L.; Chavarriaga, Ricardo; Chase, Steven M.; Bleichner, Martin G.; Batista, Aaron; Anderson, Charles W.; Aarnoutse, Erik J.

2017-01-01

The Sixth International Brain–Computer Interface (BCI) Meeting was held 30 May–3 June 2016 at the Asilomar Conference Grounds, Pacific Grove, California, USA. The conference included 28 workshops covering topics in BCI and brain–machine interface research. Topics included BCI for specific populations or applications, advancing BCI research through use of specific signals or technological advances, and translational and commercial issues to bring both implanted and non-invasive BCIs to market. BCI research is growing and expanding in the breadth of its applications, the depth of knowledge it can produce, and the practical benefit it can provide both for those with physical impairments and the general public. Here we provide summaries of each workshop, illustrating the breadth and depth of BCI research and highlighting important issues and calls for action to support future research and development. PMID:29152523

Workshops of the Sixth International Brain-Computer Interface Meeting: brain-computer interfaces past, present, and future.

Science.gov (United States)

Huggins, Jane E; Guger, Christoph; Ziat, Mounia; Zander, Thorsten O; Taylor, Denise; Tangermann, Michael; Soria-Frisch, Aureli; Simeral, John; Scherer, Reinhold; Rupp, Rüdiger; Ruffini, Giulio; Robinson, Douglas K R; Ramsey, Nick F; Nijholt, Anton; Müller-Putz, Gernot; McFarland, Dennis J; Mattia, Donatella; Lance, Brent J; Kindermans, Pieter-Jan; Iturrate, Iñaki; Herff, Christian; Gupta, Disha; Do, An H; Collinger, Jennifer L; Chavarriaga, Ricardo; Chase, Steven M; Bleichner, Martin G; Batista, Aaron; Anderson, Charles W; Aarnoutse, Erik J

2017-01-01

The Sixth International Brain-Computer Interface (BCI) Meeting was held 30 May-3 June 2016 at the Asilomar Conference Grounds, Pacific Grove, California, USA. The conference included 28 workshops covering topics in BCI and brain-machine interface research. Topics included BCI for specific populations or applications, advancing BCI research through use of specific signals or technological advances, and translational and commercial issues to bring both implanted and non-invasive BCIs to market. BCI research is growing and expanding in the breadth of its applications, the depth of knowledge it can produce, and the practical benefit it can provide both for those with physical impairments and the general public. Here we provide summaries of each workshop, illustrating the breadth and depth of BCI research and highlighting important issues and calls for action to support future research and development.

2015 Inverter Workshop | Photovoltaic Research | NREL

Science.gov (United States)

Inverter Workshop 2015 Inverter Workshop Wednesday, February 25, 2015 Chair: Jack Flicker In about inverters. This workshop represented a follow-on to the inverter workshops that Sandia National conversations between module and inverter experts. Agenda For a detailed schedule of the day's events, access

First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains: Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V.; Link, H.; McDade, M.; Mander, A.; Fox, J. C.; Rigas, N.

2013-11-01

This report summarizes the proceedings of the First International Workshop on Grid Simulator Testing of Wind Turbine Drivetrains, held from June 13 to 14, 2013, at the National Renewable Energy Laboratory's National Wind Technology Center, located south of Boulder, Colorado. The workshop was sponsored by the U.S. Department of Energy and cohosted by the National Renewable Energy Laboratory and Clemson University under ongoing collaboration via a cooperative research and development agreement. The purpose of the workshop was to provide a forum to discuss the research, testing needs, and state-of-the-art apparatuses involved in grid compliance testing of utility-scale wind turbine generators. This includes both dynamometer testing of wind turbine drivetrains ('ground testing') and field testing grid-connected wind turbines. Four sessions followed by discussions in which all attendees of the workshop were encouraged to participate comprised the workshop.

Advancing Alternative Analysis: Integration of Decision Science.

Science.gov (United States)

Malloy, Timothy F; Zaunbrecher, Virginia M; Batteate, Christina M; Blake, Ann; Carroll, William F; Corbett, Charles J; Hansen, Steffen Foss; Lempert, Robert J; Linkov, Igor; McFadden, Roger; Moran, Kelly D; Olivetti, Elsa; Ostrom, Nancy K; Romero, Michelle; Schoenung, Julie M; Seager, Thomas P; Sinsheimer, Peter; Thayer, Kristina A

2017-06-13

Decision analysis-a systematic approach to solving complex problems-offers tools and frameworks to support decision making that are increasingly being applied to environmental challenges. Alternatives analysis is a method used in regulation and product design to identify, compare, and evaluate the safety and viability of potential substitutes for hazardous chemicals. We assessed whether decision science may assist the alternatives analysis decision maker in comparing alternatives across a range of metrics. A workshop was convened that included representatives from government, academia, business, and civil society and included experts in toxicology, decision science, alternatives assessment, engineering, and law and policy. Participants were divided into two groups and were prompted with targeted questions. Throughout the workshop, the groups periodically came together in plenary sessions to reflect on other groups' findings. We concluded that the further incorporation of decision science into alternatives analysis would advance the ability of companies and regulators to select alternatives to harmful ingredients and would also advance the science of decision analysis. We advance four recommendations: a ) engaging the systematic development and evaluation of decision approaches and tools; b ) using case studies to advance the integration of decision analysis into alternatives analysis; c ) supporting transdisciplinary research; and d ) supporting education and outreach efforts. https://doi.org/10.1289/EHP483.

Emerging methods and tools for environmental risk assessment, decision-making, and policy for nanomaterials: summary of NATO Advanced Research Workshop

DEFF Research Database (Denmark)

Linkov, I; Steevens, J; Adlakha-Hutcheon, G

2009-01-01

and the environment. A unique feature of this workshop was its interdisciplinary nature and focus on the practical needs of policy decision makers. Workshop presentations and discussion panels were structured along four main themes: technology and benefits, human health risk, environmental risk, and policy......Nanomaterials and their associated technologies hold promising opportunities for the development of new materials and applications in a wide variety of disciplines, including medicine, environmental remediation, waste treatment, and energy conservation. However, current information regarding...... the environmental effects and health risks associated with nanomaterials is limited and sometimes contradictory. This article summarizes the conclusions of a 2008 NATO workshop designed to evaluate the wide-scale implications (e.g., benefits, risks, and costs) of the use of nanomaterials on human health...

Artificial intelligence approach to interwell log correlation

Energy Technology Data Exchange (ETDEWEB)

Lim, Jong-Se [Korea Maritime University, Pusan(Korea); Kang, Joo Myung [Seoul National University, Seoul(Korea); Kim, Jung Whan [Korea National Oil Corp., Anyang(Korea)

2000-04-30

This paper describes a new approach to automated interwell log correlation using artificial intelligence and principal component analysis. The approach to correlate wire line logging data is on the basis of a large set of subjective rules that are intended to represent human logical processes. The data processed are mainly the qualitative information such as the characteristics of the shapes extracted along log traces. The apparent geologic zones are identified by pattern recognition for the specific characteristics of log trace collected as a set of objects by object oriented programming. The correlation of zones between wells is made by rule-based inference program. The reliable correlation can be established from the first principal component logs derived from both the important information around well bore and the largest common part of variances of all available well log data. Correlation with field log data shows that this approach can make interwell log correlation more reliable and accurate. (author). 6 refs., 7 figs.

Tandem mirror theory workshop

International Nuclear Information System (INIS)

1981-05-01

The workshop was divided into three sections which were constituted according to subject matter: RF Heating, MHD Equilibrium and Stability, and Transport and Microstability. An overview from Livermore's point of view was given at the beginning of each session. Each session was assigned a secretary to take notes. These notes have been used in preparing this report on the workshop. The report includes the activities, conclusions, and recommendations of the workshop

Report on the workshop on new directions in soft x-ray near-threshold phenomena

International Nuclear Information System (INIS)

Lindle, D.W.; Perera, R.C.C.

1988-07-01

The ''Workshop on New Directions in Soft X-Ray Near-Threshold Phenomena'' was held at the Asilomar Conference Center in Pacific Grove, CA on March 1--4, 1987. It was attended by 59 scientists from 8 countries, representing 27 institutions. Major funding for the meeting was donated by L-Division of the Lawrence Livermore National Laboratory, who hosted and organized two previous workshops on photoabsorption and scattering in the soft x-ray energy range. Additional funding was provided by the User's Group of the Advanced Light Source. The Workshop, as its name suggests, emphasized physical phenomena in atoms, molecules, and solids near inner-shell thresholds. Of particular interest were threshold ionization, post-collisional interaction, resonant photoemission and fluorescence, and multi-electron effects such as shake-up and shake-off. In these areas and others, special consideration was given to presenting recent discoveries and potential ''new directions'' for future work