Integrated Process Design and Control of Multi-element Reactive Distillation Processes

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2016-01-01

In this work, integrated process design and control of reactive distillation processes involving multi-elements is presented. The reactive distillation column is designed using methods and tools which are similar in concept to non-reactive distillation design methods, such as driving force approach....... The methods employed in this work are based on equivalent element concept. This concept facilitates the representation of a multi-element reactive system as equivalent binary light and heavy key elements. First, the reactive distillation column is designed at the maximum driving force where through steady...

DYNAMIC SIMULATION AND FUZZY CONTROL OF A CONTINUOUS DISTILLATION COLUMN

OpenAIRE

Arbildo López, A.; Lombira Echevarría, J.; Osario López, l.

2014-01-01

The objective of this work is the study of the dinamic simulation and fuzzy control of a multicomponent continuous distillation column. In this work, the mathematical model of the distillation column and the computing program for the simulation are described. Also, the structure and implementation of the fuzzy controller are presentad. Finally, the results obtained using this programare compared with those reported in the scientific literature for different mixtures. El objetivo de nuestra...

Robust Geometric Control of a Distillation Column

DEFF Research Database (Denmark)

Kymmel, Mogens; Andersen, Henrik Weisberg

1987-01-01

A frequency domain method, which makes it possible to adjust multivariable controllers with respect to both nominal performance and robustness, is presented. The basic idea in the approach is that the designer assigns objectives such as steady-state tracking, maximum resonance peaks, bandwidth, m...... is used to examine and improve geometric control of a binary distillation column....

Nonlinear control of a multicomponent distillation process coupled with a binary distillation model as an EKF predictor.

Science.gov (United States)

Jana, Amiya Kumar; Ganguly, Saibal; Samanta, Amar Nath

2006-10-01

The work is devoted to design the globally linearizing control (GLC) strategy for a multicomponent distillation process. The control system is comprised with a nonlinear transformer, a nonlinear closed-loop state estimator [extended Kalman filter (EKF)], and a linear external controller [conventional proportional integral (PI) controller]. The model of a binary distillation column has been used as a state predictor to avoid huge design complexity of the EKF estimator. The binary components are the light key and the heavy key of the multicomponent system. The proposed GLC-EKF (GLC in conjunction with EKF) control algorithm has been compared with the GLC-ROOLE [GLC coupled with reduced-order open-loop estimator (ROOLE)] and the dual-loop PI controller based on set point tracking and disturbance rejection performance. Despite huge process/predictor mismatch, the superiority of the GLC-EKF has been inspected over the GLC-ROOLE control structure.

Multivariable model predictive control design of reactive distillation column for Dimethyl Ether production

Science.gov (United States)

Wahid, A.; Putra, I. G. E. P.

2018-03-01

Dimethyl ether (DME) as an alternative clean energy has attracted a growing attention in the recent years. DME production via reactive distillation has potential for capital cost and energy requirement savings. However, combination of reaction and distillation on a single column makes reactive distillation process a very complex multivariable system with high non-linearity of process and strong interaction between process variables. This study investigates a multivariable model predictive control (MPC) based on two-point temperature control strategy for the DME reactive distillation column to maintain the purities of both product streams. The process model is estimated by a first order plus dead time model. The DME and water purity is maintained by controlling a stage temperature in rectifying and stripping section, respectively. The result shows that the model predictive controller performed faster responses compared to conventional PI controller that are showed by the smaller ISE values. In addition, the MPC controller is able to handle the loop interactions well.

27 CFR 27.75 - Samples of distilled spirits, wine, and beer for quality control purposes.

Science.gov (United States)

2010-04-01

... spirits, wine, and beer for quality control purposes. 27.75 Section 27.75 Alcohol, Tobacco Products and... DISTILLED SPIRITS, WINES, AND BEER General Requirements Exemptions § 27.75 Samples of distilled spirits, wine, and beer for quality control purposes. Samples of distilled spirits, wine, and beer in containers...

Control of distributed heat transfer mechanisms in membrane distillation plants

KAUST Repository

Laleg-Kirati, Taous-Meriem

2017-01-05

Various examples are provided that are related to boundary control in membrane distillation (MD) processes. In one example, a system includes a membrane distillation (MD) process comprising a feed side and a permeate side separated by a membrane boundary layer; and processing circuitry configured to control a water production rate of the MD process based at least in part upon a distributed heat transfer across the membrane boundary layer. In another example, a method includes determining a plurality of estimated temperature states of a membrane boundary layer separating a feed side and a permeate side of a membrane distillation (MD) process; and adjusting inlet flow rate or inlet temperature of at least one of the feed side or the permeate side to maintain a difference temperature along the membrane boundary layer about a defined reference temperature based at least in part upon the plurality of estimated temperature states.

Honeywell Cascade Distiller System Performance Testing Interim Results

Science.gov (United States)

Callahan, Michael R.; Sargusingh, Miriam

2014-01-01

The ability to recover and purify water through physiochemical processes is crucial for realizing long-term human space missions, including both planetary habitation and space travel. Because of their robust nature, distillation systems have been actively pursued as one of the technologies for water recovery. The Cascade Distillation System (CDS) is a vacuum rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. The CDS was previously under development through Honeywell and NASA. In 2009, an assessment was performed to collect data to support down-selection and development of a primary distillation technology for application in a lunar outpost water recovery system. Based on the results of this testing, an expert panel concluded that the CDS showed adequate development maturity, TRL-4, together with the best product water quality and competitive weight and power estimates to warrant further development. The Advanced Exploration Systems (AES) Water Recovery Project (WRP) worked to address weaknesses identified by The Panel; namely bearing design and heat pump power efficiency. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades. The CDS will also have been challenged with ISS analog waste streams and a subset of those being considered for Exploration architectures. This paper details interim results of the AES WRP CDS performance testing.

Model predictive control of a crude oil distillation column

Directory of Open Access Journals (Sweden)

Morten Hovd

1999-04-01

Full Text Available The project of designing and implementing model based predictive control on the vacuum distillation column at the Nynäshamn Refinery of Nynäs AB is described in this paper. The paper describes in detail the modeling for the model based control, covers the controller implementation, and documents the benefits gained from the model based controller.

Method of controlling a distillatory coulumn in a liquefaction and distillation device for radioactive rare gases

International Nuclear Information System (INIS)

Kimura, Shigeru; Awata, Yoshihisa.

1975-01-01

Object: To automatically and securely perform controlling purity of column bottom liquid, which is most difficult in the liquefaction and distillation device. Structure: In a liquefaction and distillation device for liquefying and separating rare gas krypton in fuel reprocessing gases, a difference in temperature between the column bottom liquid (column top) and the distillation portion is detected so as to maintain temperature in the distillation portion of the distilling column constant, and the vaporization amount of column bottom liquid is varied with the difference in temperature to control purity of the column bottom liquid. (Kamimura, M.)

Sensor locations and noise reduction in high-purity batch distillation control loops

Directory of Open Access Journals (Sweden)

Oisiovici R.M.

2000-01-01

Full Text Available The influence of the sensor locations on the composition control of high-purity batch distillation columns has been investigated. Using concepts of the nonlinear control theory, an input-output linearizing controller was implemented to keep the distillate composition constant at a desired value by varying the reflux ratio. An Extended Kalman Filter was developed to estimate the compositions required in the control algorithm using temperature measurements. In the presence of measurement noise, the control performance depended greatly on the sensor locations. Placing the sensors further from the top stages reduced the detrimental effects of noise but increased the inference error. To achieve accurate composition control, both noise reduction and composition estimate accuracy should be considered in the selection of the sensor locations.

Design and implementation of a control structure for quality products in a crude oil atmospheric distillation column.

Science.gov (United States)

Sotelo, David; Favela-Contreras, Antonio; Sotelo, Carlos; Jiménez, Guillermo; Gallegos-Canales, Luis

2017-11-01

In recent years, interest for petrochemical processes has been increasing, especially in refinement area. However, the high variability in the dynamic characteristics present in the atmospheric distillation column poses a challenge to obtain quality products. To improve distillates quality in spite of the changes in the input crude oil composition, this paper details a new design of a control strategy in a conventional crude oil distillation plant defined using formal interaction analysis tools. The process dynamic and its control are simulated on Aspen HYSYS ® dynamic environment under real operating conditions. The simulation results are compared against a typical control strategy commonly used in crude oil atmospheric distillation columns. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Continuous fractional distillation of petroleum

Energy Technology Data Exchange (ETDEWEB)

1921-11-05

This invention has for its object a process of distillation, fractional, and continuous, of shale oil, tar, etc., characterized by the vapors leaving the evaporation chamber being forced, before condensation, to go over a continuous circuit. The vapors traverse first a preheater then return to the vaporization chamber in which they are passed along large surfaces and by application of the counter-current principle in contact with the liquid to be distilled. They stream through the chamber in a continuous manner (the quantity of vapor emitted in the circuit being determined in a manner to advance the distillation just to completion); the excess of vapor formed being removed from the circuit and sent to a condensing apparatus for fractionation.

Optimal Operation and Stabilising Control of the Concentric Heat-Integrated Distillation Column

DEFF Research Database (Denmark)

Bisgaard, Thomas; Skogestad, Sigurd; Huusom, Jakob Kjøbsted

2016-01-01

A systematic control structure design method is applied on the concentric heat integrated distillation column (HIDiC) separating benzene and toluene. A degrees of freedom analysis is provided for identifying potential manipulated and controlled variables. Optimal operation is mapped and active...

Supervisory Model Predictive Control of the Heat Integrated Distillation Column

DEFF Research Database (Denmark)

Meyer, Kristian; Bisgaard, Thomas; Huusom, Jakob Kjøbsted

2017-01-01

This paper benchmarks a centralized control system based on model predictive control for the operation of the heat integrated distillation column (HIDiC) against a fully decentralized control system using the most complete column model currently available in the literature. The centralized control...... system outperforms the decentralized system, because it handles the interactions in the HIDiC process better. The integral absolute error (IAE) is reduced by a factor of 2 and a factor of 4 for control of the top and bottoms compositions, respectively....

Process modeling and control applied to real-time monitoring of distillation processes by near-infrared spectroscopy.

Science.gov (United States)

de Oliveira, Rodrigo R; Pedroza, Ricardo H P; Sousa, A O; Lima, Kássio M G; de Juan, Anna

2017-09-08

A distillation device that acquires continuous and synchronized measurements of temperature, percentage of distilled fraction and NIR spectra has been designed for real-time monitoring of distillation processes. As a process model, synthetic commercial gasoline batches produced in Brazil, which contain mixtures of pure gasoline blended with ethanol have been analyzed. The information provided by this device, i.e., distillation curves and NIR spectra, has served as initial information for the proposal of new strategies of process modeling and multivariate statistical process control (MSPC). Process modeling based on PCA batch analysis provided global distillation trajectories, whereas multiset MCR-ALS analysis is proposed to obtain a component-wise characterization of the distillation evolution and distilled fractions. Distillation curves, NIR spectra or compressed NIR information under the form of PCA scores and MCR-ALS concentration profiles were tested as the seed information to build MSPC models. New on-line PCA-based MSPC approaches, some inspired on local rank exploratory methods for process analysis, are proposed and work as follows: a) MSPC based on individual process observation models, where multiple local PCA models are built considering the sole information in each observation point; b) Fixed Size Moving Window - MSPC, in which local PCA models are built considering a moving window of the current and few past observation points; and c) Evolving MSPC, where local PCA models are built with an increasing window of observations covering all points since the beginning of the process until the current observation. Performance of different approaches has been assessed in terms of sensitivity to fault detection and number of false alarms. The outcome of this work will be of general use to define strategies for on-line process monitoring and control and, in a more specific way, to improve quality control of petroleum derived fuels and other substances submitted

Optimal design and control of solar driven air gap membrane distillation desalination systems

International Nuclear Information System (INIS)

Chen, Yih-Hang; Li, Yu-Wei; Chang, Hsuan

2012-01-01

Highlights: ► Air gap membrane distillation unit was used in the desalination plants. ► Aspen Custom Molder was used to simulate each unit of desalination plants. ► Design parameters were investigated to obtain the minimum total annual cost. ► The control structure was proposed to operate desalination plants all day long. -- Abstract: A solar heated membrane distillation desalination system is constructed of solar collectors and membrane distillation devices for increasing pure water productivity. This technically and economically feasible system is designed to use indirect solar heat to drive membrane distillation processes to overcome the unstable supply of solar radiation from sunrise to sunset. The solar heated membrane distillation desalination system in the present study consisted of hot water storage devices, heat exchangers, air gap membrane distillation units, and solar collectors. Aspen Custom Molder (ACM) software was used to model and simulate each unit and establish the cost function of a desalination plant. From Design degree of freedom (DOF) analysis, ten design parameters were investigated to obtain the minimum total annual cost (TAC) with fixed pure water production rate. For a given solar energy density profile of typical summer weather, the minimal TAC per 1 m 3 pure water production can be found at 500 W/m 2 by varying the solar energy intensity. Therefore, we proposed two modes for controlling the optimal design condition of the desalination plant; day and night. In order to widen the operability range of the plant, the sensitivity analysis was used to retrofit the original design point to lower the effluent temperature from the solar collector by increasing the hot water recycled stream. The simulation results show that the pure water production can be maintained at a very stable level whether in sunny or cloudy weather.

Cascade Distillation Subsystem Development: Progress Toward a Distillation Comparison Test

Science.gov (United States)

Callahan, M. R.; Lubman, A.; Pickering, Karen D.

2009-01-01

Recovery of potable water from wastewater is essential for the success of long-duration manned missions to the Moon and Mars. Honeywell International and a team from NASA Johnson Space Center (JSC) are developing a wastewater processing subsystem that is based on centrifugal vacuum distillation. The wastewater processor, referred to as the Cascade Distillation Subsystem (CDS), utilizes an innovative and efficient multistage thermodynamic process to produce purified water. The rotary centrifugal design of the system also provides gas/liquid phase separation and liquid transport under microgravity conditions. A five-stage subsystem unit has been designed, built, delivered and integrated into the NASA JSC Advanced Water Recovery Systems Development Facility for performance testing. A major test objective of the project is to demonstrate the advancement of the CDS technology from the breadboard level to a subsystem level unit. An initial round of CDS performance testing was completed in fiscal year (FY) 2008. Based on FY08 testing, the system is now in development to support an Exploration Life Support (ELS) Project distillation comparison test expected to begin in early 2009. As part of the project objectives planned for FY09, the system will be reconfigured to support the ELS comparison test. The CDS will then be challenged with a series of human-gene-rated waste streams representative of those anticipated for a lunar outpost. This paper provides a description of the CDS technology, a status of the current project activities, and data on the system s performance to date.

Control of a reactive batch distillation process using an iterative learning technique

International Nuclear Information System (INIS)

Ahn, Hyunsoo; Lee, Kwang Soon; Kim, Mansuk; Lee, Juhyun

2014-01-01

Quadratic criterion-based iterative learning control (QILC) was applied to a numerical reactive batch distillation process, in which methacrylic anhydride (MAN) is produced through the reaction of methacrylic acid with acetic anhydride. The role of distillation is to shift the equilibrium conversion toward the direction of the product by removing acetic acid (AcH), a by-product of the reaction. Two temperatures at both ends of the column were controlled by individual control loops. A nonlinear PID controller manipulating the reflux ratio was employed to regulate the top temperature at the boiling point of AcH. A constrained QILC was used for the tracking of the reactor temperature. A time-varying reference trajectory for the reactor temperature that satisfies the target conversion and purity of MAN was obtained through repeated simulations and confirmation experiments in the pilot plant. The QILC achieved satisfactory tracking in several batch runs with gentle control movements, while the PID control as a substitute of the QILC in a comparative study exhibited unacceptable performance

Dynamic effects of diabatization in distillation columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2013-01-01

The dynamic effects of diabatization in distillation columns are investigated in simulation emphasizing the heat-integrated distillation column (HIDiC). A generic, dynamic, first-principle model has been formulated, which is flexible enough to describe various diabatic distillation configurations....... Dynamic Relative Gain Array and Singular Value Analysis have been applied in a comparative study of a conventional distillation column and a HIDiC. The study showed increased input-output coupling due to diabatization. Feasible SISO control structures for the HIDiC were also found and control...

Dynamic Effects of Diabatization in Distillation Columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2012-01-01

The dynamic eects of diabatization in distillation columns are investigated in simulation with primary focus on the heat-integrated distillation column (HIDiC). A generic, dynamic, rst-principle model has been formulated, which is exible to describe various diabatic distillation congurations....... Dynamic Relative Gain Array and Singular Value Analysis have been applied in a comparative study of a conventional distillation column and a HIDiC. The study showed increased input-output coupling due to diabatization. Feasible SISO control structures for the HIDiC were also found. Control...

Modeling RP-1 Fuel Advanced Distillation Data using Comprehensive Two-Dimensional Gas Chromatography Coupled with Time-of-Flight Mass Spectrometry and Partial Least Squares Analysis

Science.gov (United States)

2014-05-07

of a variety of complex liquid samples including, but not limited to, crude oil [12], gasoline [16], biodiesel fuel [17, 19], jet fuel [5, 10, 11...measurements for corrosive fluids: Application to two crude oils . Fuel 87:3055–3064. doi: 10.1016/j.fuel.2008.04.032 13. Ott LS, Hadler AB, Bruno TJ...Windom BC, Bruno TJ (2013) Application of Pressure-Controlled Advanced Distillation Curve Analysis: Virgin and Waste Oils . Ind Eng Chem Res 52:327–337

Low temperature distillation

Energy Technology Data Exchange (ETDEWEB)

1937-07-21

To distil mineral or organic material, the material is heated by means of a hot gas entering into contact with and traversing the material in a horizontal direction. The vertical retort is charged with material from the hopper and hot gases from the furnace after traversing the boiler enter the preheating zone, pass through the slots and charge therein and are educted through connection by the blower. The charge passes downwardly to the distillation zone wherein hot gases from the heater are passed via pipe and slots through the chambers and to the pipe controlled by the dampers. These gases are recycled by the fan through the heater and chamber, that portion of the gases corresponding to the amount of vapours evolved from the distillation being evacuated via the pipe to the condensing plant not shown. Steam and/or a limited quantity of water may be admitted to the distillation zone.

Distillation Column Flooding Predictor

Energy Technology Data Exchange (ETDEWEB)

George E. Dzyacky

2010-11-23

The Flooding Predictor™ is a patented advanced control technology proven in research at the Separations Research Program, University of Texas at Austin, to increase distillation column throughput by over 6%, while also increasing energy efficiency by 10%. The research was conducted under a U. S. Department of Energy Cooperative Agreement awarded to George Dzyacky of 2ndpoint, LLC. The Flooding Predictor™ works by detecting the incipient flood point and controlling the column closer to its actual hydraulic limit than historical practices have allowed. Further, the technology uses existing column instrumentation, meaning no additional refining infrastructure is required. Refiners often push distillation columns to maximize throughput, improve separation, or simply to achieve day-to-day optimization. Attempting to achieve such operating objectives is a tricky undertaking that can result in flooding. Operators and advanced control strategies alike rely on the conventional use of delta-pressure instrumentation to approximate the column’s approach to flood. But column delta-pressure is more an inference of the column’s approach to flood than it is an actual measurement of it. As a consequence, delta pressure limits are established conservatively in order to operate in a regime where the column is never expected to flood. As a result, there is much “left on the table” when operating in such a regime, i.e. the capacity difference between controlling the column to an upper delta-pressure limit and controlling it to the actual hydraulic limit. The Flooding Predictor™, an innovative pattern recognition technology, controls columns at their actual hydraulic limit, which research shows leads to a throughput increase of over 6%. Controlling closer to the hydraulic limit also permits operation in a sweet spot of increased energy-efficiency. In this region of increased column loading, the Flooding Predictor is able to exploit the benefits of higher liquid

Control characteristics of cryogenic distillation column with a feedback stream for fusion reactor

International Nuclear Information System (INIS)

Yamanishi, Toshihiko; Okuno, Kenji

1997-01-01

The control characteristics of the cryogenic distillation column with a feedback stream have been discussed based on computer simulation results. This column plays an important role in fusion reactor. A new control system was proposed from the simulation results. The flow rate of top product is determined from the composition and flow rate of a main feed stream by a feedforward control loop. The flow rates of the feedback stream and vapor stream within the column are proportionally changed with a corresponding change of feed flow rate. The flow rate of vapor stream within the column is further adjusted to maintain product purity by a feedback control loop. The proposed system can control the product purity for a large fluctuation of feed composition, a change of feed flow rate, and an increase or decrease of the number of total theoretical stages of the column. The control system should be designed for each column by considering its operating conditions and function. The present study gives us a basic procedure for the design method of the control system of the cryogenic distillation column. (author)

Design of Unconstrained DMC to Improve the Distillate Product Purity of the Distillation Column

Directory of Open Access Journals (Sweden)

Bhat Vinayambika S.

2016-01-01

Full Text Available This paper demonstrates the use of unconstrained Dynamic Matrix Control (DMC to control the process transfer function with time delay. The selection of tuning parameter is challenging task in predictive control algorithm. The DMC scheme is designed and it is used here to control the process transfer function, First Order Plant with Dead Time (FOPDT model. Here, one manipulated variable (reflux and one controlled variable (distillate is considered for the implementation. The algorithm significantly controls the reflux to improve the distillate product purity. The simulation is done using MATLAB m-file. Both servo and regulatory responses were obtained. The simulation result validates the effectiveness of the proposed algorithm.

The interactions of design, control and operability in reactive distillation systems

DEFF Research Database (Denmark)

Georgiadis, M.C.; Schenk, Myrian Andrea; Pistikopoulos, Stratos

2002-01-01

is a strong function of the process design and potential operability bottlenecks are identified. In the second approach, the process design and the control system are optimized simultaneously leading to a more economically beneficial and better controlled system than that obtained using the sequential......In this work the design and control of a reactive distillation column, described by a rigorous dynamic model, is tackled via two different optimization approaches. In the first, the steady-state process design and the control system are optimized sequentially. It is shown that operability...

EKF composition estimation and GMC control of a reactive distillation column

Science.gov (United States)

Tintavon, Sirivimon; Kittisupakorn, Paisan

2017-08-01

This research work proposes an extended Kalman filter (EKF) estimator to give estimates of product composition and a generic model controller (GMC) to control the temperature of a reactive distillation column (RDC). One of major difficulties to control the RDC is large time delays of product composition measurement. Therefore, the estimates of the product composition are needed and determined based on available and reliable measured tray temperature via the extended Kalman Filter (EKF). With these estimates, the GMC controller is applied to control the RDC's temperature. The performance of the EKF estimator under the GMC control is evaluated in various disturbances and set point change.

Model predictive control in light naphtha distillation column of gasoline hydrogenation process

Directory of Open Access Journals (Sweden)

Kornkrit Chiewchanchairat

2015-03-01

Full Text Available The main scope of this research is for designing and implementing of model predictive control (MPC on the light naphtha distillation column of gasoline hydrogenation process. This model is designed by using robust multivariable predictive control technology (RMPCT. The performance of MPC controller is better than PID controllers 32.1 % those are comparing by using as the same of objective function and also in the MPC controller can be used for steam optimization that is shown in this research, stream consumption is reduced 6.6 Kg/ m3 of fresh feed.

In-line estimation of sulfur and nitrogen contents during hydrotreating of middle distillates

Directory of Open Access Journals (Sweden)

M. E. Pacheco

2009-12-01

Full Text Available The main objective of this work is analyzing whether it is possible to develop an empirical correlation for in-line estimation of the sulfur and nitrogen contents of the middle distillates Hydrotreating (HDT products for control purposes. Correlations are based only on readily available in-line information of specific gravity variation between feedstock and products, without considering any piece of information about the kinetic behavior of the catalyst. Experimental data were obtained in pilot plants under operating conditions that are representative of refinery operations. Results indicate that the removal of nitrogen and sulfur compounds during middle distillates HDT can be monitored in-line in real time, based on the available measurements of specific gravity. This allows for development and implementation of advanced in-line procedures for monitoring and control of the HDT process in real time.

Distillation methods

International Nuclear Information System (INIS)

Konecny, C.

1975-01-01

Two main methods of separation using the distillation method are given and evaluated, namely evaporation and distillation in carrier gas flow. Two basic apparatus are described for illustrating the methods used. The use of the distillation method in radiochemistry is documented by a number of examples of the separation of elements in elemental state, volatile halogenides and oxides. Tables give a survey of distillation methods used for the separation of the individual elements and give conditions under which this separation takes place. The suitability of the use of distillation methods in radiochemistry is discussed with regard to other separation methods. (L.K.)

Systematic Integrated Process Design and Control of Reactive Distillation Processes Involving Multi-elements

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2016-01-01

driving force approach. Next, through analytical, steady-state and closed-loop dynamic analysis it is verified that the control structure, disturbance rejection and energy requirement of the reactive distillation column is better than any other operation point that is not at the maximum driving force...

Soft sensor based composition estimation and controller design for an ideal reactive distillation column.

Science.gov (United States)

Vijaya Raghavan, S R; Radhakrishnan, T K; Srinivasan, K

2011-01-01

In this research work, the authors have presented the design and implementation of a recurrent neural network (RNN) based inferential state estimation scheme for an ideal reactive distillation column. Decentralized PI controllers are designed and implemented. The reactive distillation process is controlled by controlling the composition which has been estimated from the available temperature measurements using a type of RNN called Time Delayed Neural Network (TDNN). The performance of the RNN based state estimation scheme under both open loop and closed loop have been compared with a standard Extended Kalman filter (EKF) and a Feed forward Neural Network (FNN). The online training/correction has been done for both RNN and FNN schemes for every ten minutes whenever new un-trained measurements are available from a conventional composition analyzer. The performance of RNN shows better state estimation capability as compared to other state estimation schemes in terms of qualitative and quantitative performance indices. Copyright © 2010 ISA. Published by Elsevier Ltd. All rights reserved.

Distilling hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Tausz, J

1924-07-16

Hydrocarbon oils such as petroleum, shale oils, lignite or coal tar oils are purified by distilling them and collecting the distillate in fractions within narrow limits so that all the impurities are contained in one or more of the narrow fractions. In distilling ligroin obtained by destructive distillation of brown coal, it is found that the coloring and resin-forming constituents are contained in the fractions distilling over at 62 to 86/sup 0/C and 108/sup 0/C. The ligroin is purified, therefore, by distillating in an apparatus provided with an efficient dephlegmotor and removing these two fractions. The distillation may be carried out wholly or in part under reduced pressure, and fractions separated under ordinary pressure may be subsequently distilled under reduced pressure. The hydrocarbons may be first separated into fractions over wider limits and the separate fractions be subjected to a further fractional distillation.

Nonlinear Lyapunov-based boundary control of distributed heat transfer mechanisms in membrane distillation plant

KAUST Repository

Eleiwi, Fadi; Laleg-Kirati, Taous-Meriem

2015-01-01

This paper presents a nonlinear Lyapunov-based boundary control for the temperature difference of a membrane distillation boundary layers. The heat transfer mechanisms inside the process are modeled with a 2D advection-diffusion equation. The model

Dry distillation

Energy Technology Data Exchange (ETDEWEB)

1939-11-30

To heat rapidly, and prevent agglutination of carbonaceous material duriing distillation of shale, a furnace of the tunnel type has four compartments (the preheating chamber, the distillation chamber proper, and two cooling chambers). Waggons, which convey the material through the distilling chamber, have perforated bottoms. Above the waggons in the distilling chamber are three heating sections having pipes which pass through the sections and communicate with the distilling chamber. Fans cause the distillation gases to circulate through the material and the pipes. The heating gases from three fire boxes are introduced into the oven, and circulate around pipes and are drawn to the discharge apertures by the fans. The heating gases introduced at two points travel in the direction of the material being treated, while the gases introduced at a third point travel in counter flow thereto. Gas is discharged by two pipes. Trucks carrying treated material are passed to two cooling chambers.

40 CFR 80.620 - What are the additional requirements for diesel fuel or distillates produced by foreign...

Science.gov (United States)

2010-07-01

... audits of the foreign refinery. (i) Inspections and audits may be either announced in advance by EPA, or... diesel fuel or distillate was produced, assurance that the diesel fuel or distillate remained segregated...: (i) Be approved in advance by EPA, based on a demonstration of ability to perform the procedures...

Reactive Distillation and Air Stripping Processes for Water Recycling and Trace Contaminant Control

Science.gov (United States)

Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

2009-01-01

Reactive distillation designs are considered to reduce the presence of volatile organic compounds in the purified water. Reactive distillation integrates a reactor with a distillation column. A review of the literature in this field has revealed a variety of functional reactive columns in industry. Wastewater may be purified by a combination of a reactor and a distiller (e.g., the EWRS or VPCAR concepts) or, in principle, through a design which integrates the reactor with the distiller. A review of the literature in reactive distillation has identified some different designs in such combinations of reactor and distiller. An evaluation of reactive distillation and reactive air stripping is presented with regards to the reduction of volatile organic compounds in the contaminated water and air. Among the methods presented, an architecture is presented for the evaluation of the simultaneous oxidation of organics in air and water. These and other designs are presented in light of potential improvements in power consumptions and air and water purities for architectures which include catalytic activity integrated into the water processor. In particular, catalytic oxidation of organics may be useful as a tool to remove contaminants that more traditional distillation and/or air stripping columns may not remove. A review of the current leading edge at the commercial level and at the research frontier in catalytically active materials is presented. Themes and directions from the engineering developments in catalyst design are presented conceptually in light of developments in the nanoscale chemistry of a variety of catalyst materials.

Microbubble Distillation for Ethanol-Water Separation

Directory of Open Access Journals (Sweden)

Atheer Al-yaqoobi

2016-01-01

Full Text Available In the current study, a novel approach for separating ethanol-water mixture by microbubble distillation technology was investigated. Traditional distillation processes require large amounts of energy to raise the liquid to its boiling point to effect removal of volatile components. The concept of microbubble distillation by comparison is to heat the gas phase rather than the liquid phase to achieve separation. The removal of ethanol from the thermally sensitive fermentation broths was taken as a case of study. Consequently the results were then compared with those which could be obtained under equilibrium conditions expected in an “ideal” distillation unit. Microbubble distillation has achieved vapour compositions higher than that which could be obtained under traditional equilibrium conditions. The separation was achieved at liquid temperature significantly less than the boiling point of the mixture. In addition, it was observed that the separation efficiency of the microbubble distillation could be increased by raising the injected air temperature, while the temperature of the liquid mixture increased only moderately. The separation efficiency of microbubble distillation was compared with that of pervaporation for the recovery of bioethanol from the thermally sensitive fermentation broths. The technology could be controlled to give high separation and energy efficiency. This could contribute to improving commercial viability of biofuel production and other coproducts of biorefinery processing.

Multipartite nonlocality distillation

International Nuclear Information System (INIS)

Hsu, Li-Yi; Wu, Keng-Shuo

2010-01-01

The stronger nonlocality than that allowed in quantum theory can provide an advantage in information processing and computation. Since quantum entanglement is distillable, can nonlocality be distilled in the nonsignalling condition? The answer is positive in the bipartite case. In this article the distillability of the multipartite nonlocality is investigated. We propose a distillation protocol solely exploiting xor operations on output bits. The probability-distribution vectors and matrix are introduced to tackle the correlators. It is shown that only the correlators with extreme values can survive the distillation process. As the main result, the amplified nonlocality cannot maximally violate any Bell-type inequality. Accordingly, a distillability criterion in the postquantum region is proposed.

Distillation principes de calcul et de contrôle Distillation. Engineering and Control Principles

Directory of Open Access Journals (Sweden)

Trambouze P.

2006-11-01

Full Text Available Cet article présente les principes de base utilisés lors de la conception et de la conduite des colonnes à distiller continues ou discontinues. Dans cet exposé d'initiation le cas des mélanges binaires est seul considéré de manière à ne pas compliquer inutilement la présentation. Par contre pour conserver à cette étude un aspect pratique, la dernière partie est consacrée aux problèmes technologiques et aux principales solutions mises en oeuvre. This article describes the basic principles used in designing and operating columns for continuous or batch distillation. The case of binary mixtures is the only one considered so as not to uselessly complicate the description. However, so as to mointain the practical nature of this study, the last part is devoted to technological problems and to the main solutions applied to them.

Development of an Exploration-Class Cascade Distillation System: Flight Like Prototype Preliminary Design

Science.gov (United States)

Callahan, Michael R.; Sargusingh, Miriam J.

2015-01-01

The ability to recover and purify water through physiochemical processes is crucial for realizing long-term human space missions, including both planetary habitation and space travel. Because of their robust nature, distillation systems have been actively pursued as one of the technologies for water recovery. One such technology is the Cascade Distillation System (CDS) a multi-stage vacuum rotary distiller system designed to recover water in a microgravity environment. Its rotating cascading distiller operates similarly to the state of the art (SOA) vapor compressor distiller (VCD), but its control scheme and ancillary components are judged to be straightforward and simpler to implement into a successful design. Through the Advanced Exploration Systems (AES) Life Support Systems (LSS) Project, the NASA Johnson Space Center (JSC) in collaboration with Honeywell International is developing a second generation flight forward prototype (CDS 2.0). The key objectives for the CDS 2.0 design task is to provide a flight forward ground prototype that demonstrates improvements over the SOA system in the areas of increased reliability and robustness, and reduced mass, power and volume. It will also incorporate exploration-class automation. The products of this task are a preliminary flight system design and a high fidelity prototype of an exploration class CDS. These products will inform the design and development of the third generation CDS which is targeted for on-orbit DTO. This paper details the preliminary design of the CDS 2.0.

Catalytic distillation structure

Science.gov (United States)

Smith, L.A. Jr.

1984-04-17

Catalytic distillation structure is described for use in reaction distillation columns, and provides reaction sites and distillation structure consisting of a catalyst component and a resilient component intimately associated therewith. The resilient component has at least about 70 volume % open space and is present with the catalyst component in an amount such that the catalytic distillation structure consists of at least 10 volume % open space. 10 figs.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Brinjes, J F

1866-03-13

Continuous distillation of shale, boghead coal, or other noncaking bituminous material is effected in one or more rotating or oscillating horizontal retorts constructed to advance the charge. In the former case, internal spiral ribs or projections are provided. In the latter case, the retort is subdivided by annular flanges provided each with an opening, and a series of double inclined projections is disposed opposite the openings. An apparatus is shown in which the material is fed continuously from a hopper, and is advanced through upper and lower oscillating retorts, provided with annular flanges, double inclined projections, and longitudinal ribs or ledges. The retorts are supported on antifriction rollers. The retort is oscillated by means of a mangle wheel and a pinion on a shaft connected by a universal joint to a driving-shaft. The retort is oscillated from the retort by means of a chain connection. The retort is situated in a chamber separated by perforated brickwork from the actual furnace chamber, so that it is subjected to a lower temperature than the retort. The hopper delivers to crushing-rollers in a lower hopper which delivers to a shoot controlled by a sliding door. A hook on the retort is connected by a pipe to the retort, and a pipe leads from the hood to a condenser. A hood at the delivery end of the retort is connected by a pipe to an airtight cooler for the residue, which is discharged through doors into a truck of other receiver.

Fouling in Membrane Distillation, Osmotic Distillation and Osmotic Membrane Distillation

Directory of Open Access Journals (Sweden)

Mourad Laqbaqbi

2017-03-01

Full Text Available Various membrane separation processes are being used for seawater desalination and treatment of wastewaters in order to deal with the worldwide water shortage problem. Different types of membranes of distinct morphologies, structures and physico-chemical characteristics are employed. Among the considered membrane technologies, membrane distillation (MD, osmotic distillation (OD and osmotic membrane distillation (OMD use porous and hydrophobic membranes for production of distilled water and/or concentration of wastewaters for recovery and recycling of valuable compounds. However, the efficiency of these technologies is hampered by fouling phenomena. This refers to the accumulation of organic/inorganic deposits including biological matter on the membrane surface and/or in the membrane pores. Fouling in MD, OD and OMD differs from that observed in electric and pressure-driven membrane processes such electrodialysis (ED, membrane capacitive deionization (MCD, reverse osmosis (RO, nanofiltration (NF, ultrafiltration (UF, microfiltration (MF, etc. Other than pore blockage, fouling in MD, OD and OMD increases the risk of membrane pores wetting and reduces therefore the quantity and quality of the produced water or the concentration efficiency of the process. This review deals with the observed fouling phenomena in MD, OD and OMD. It highlights different detected fouling types (organic fouling, inorganic fouling and biofouling, fouling characterization techniques as well as various methods of fouling reduction including pretreatment, membrane modification, membrane cleaning and antiscalants application.

Distilling hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Schulze, J E

1923-03-19

In distilling mineral oils such as petroleum, shale oil, distillates and topped or residual oils, particularly to obtain lubricating oils, the distillation is carried out under reduced pressures below an absolute pressure of 25 mm. of mercury and preferably below about 5 mm. of mercury, and the distillate is collected in fractions determined by the physical characteristics, such as viscosity, flash point, fire point, etc. Superheated steam may be passed through the liquid during distillation. A horizontal cylindrical still provided with cross braces and peripheral ribs interrupted at the base is connected through a condensing coil immersed in a steam chest and a baffled chamber with distillate receiver and is evacuated by a pump. Steam from a boiler and superheater is injected into the still through a perforated pipe. Steam and light oil vapors passing from the chamber are condensed in a coil.

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1946-08-29

A continuous method of distilling shale to produce valuable hydrocarbon oils is described which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors from the zone, mixing fresh cold shale with the hydrocarbon vapors to quench the same, whereby the fresh shale is preheated, recovering hydrocarbon vapors and product vapors from the mixture and withdrawing preheated shale from the mixture and charging it to a shale distillation zone.

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Heyl, G E

1917-02-06

The yield of oil obtained by distilling shale is increased by first soaking the shale with about 10 percent of its volume of a liquid hydrocarbon for a period of 24 hours or longer. Distillation is carried on up to a temperature of about 220/sup 0/C., and a further 10 percent of hydrocarbon is then added and the distillation continued up to a temperature of about 400/sup 0/C.

Sodium distiller II

International Nuclear Information System (INIS)

Goncalves, A.C.; Castro, P.M. e; Torres, A.R.; Correa, S.M.

1990-01-01

A sodium distiller allows the evaluation of the sodium purity, contained in plants and circuits of Fast Reactors. The sodium distillers of the IEN Reactor's Department was developed initially as a prototype, for the testing of the distillation process and in a second step, as a equipment dedicated to attendance the operation of these circuits. This last one was build in stainless steel, with external heat, rotating crucible of nickel for four samples, purge system for pipe cleaning and a sight glass that permits the observation of the distillation during all the operation. The major advantage of this equipment is the short time to do a distillation operation, which permits its routine utilization. As a consequence of the development of the distillers and its auxiliary systems an important amount of new information was gathered concerning components and systems behaviour under high temperature, vacuum and sodium. (author)

Distilling tar; distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Brash, P; Young, W

1866-09-17

The tarry residue, which separates on treating crude shale oil with sulfuric acid, is redistilled, in the manner described in Specification No. 1278, A.D. 1866, together with shale. Previous to the distillation, the acid is neutralized with lime, or may be separated by blowing steam into the tar and adding salt. The purified tar thus obtained is absorbed by ashes, or is mixed with lime or other alkaline matter, or the shale may be mixed with lime and distilled with the tar, which is allowed to flow over and through the shale during the process. The tar obtained in the purification of natural paraffin may be similarly utilized.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

1938-07-05

A process and apparatus for the destructive distillation at low temperature of mineral or organic material particularly oil shale, is given in which the process comprises distilling the material in a horizontal gaseous stream, subjecting the hot residues to the action of a gaseous stream containing a predetermined amount of oxygen so as to burn, at least partly, the carbon-containing substances, and the process uses the gases from this combustion for the indirect heating of the gases serving for the distillation.

Refreshment topics II: Design of distillation columns

Directory of Open Access Journals (Sweden)

Milojević Svetomir

2006-01-01

Full Text Available For distillation column design it is necessary to define all the variable parameters such as component concentrations in different streams temperatures, pressures, mass and energy flow, which are used to represent the separation process of some specific system. They are related to each other according to specific laws, and if the number of such parameters exceeds the number of their relationships, in order to solve a problem some of them must be specified in advance or some constraints assumed for the mass balance, the balance of energy, phase equilibria or chemical equilibria. Knowledge of specific elements which are the constituents of a distillation unit must be known to define the number of design parameters as well as some additional apparati also necessary to realize the distilation. Each separate apparatus might be designed and constructed only if all the necessary and variable parameters for such a unit are defined. This is the right route to solve a distilation unit in many different cases. The construction of some distillation unit requires very good knowledge of mass, heat and momentum transfer phenomena. Moreover, the designer needs to know which kind of apparatus will be used in the distillation unit to realize a specific production process. The most complicated apparatus in a rectification unit is the distillation column. Depending on the complexity of the separation process one, two or more columns are often used. Additional equipment are heat exchangers (reboilers, condensers, cooling systems, heaters, separators, tanks for reflux distribution, tanks and pumps for feed transportation, etc. Such equipment is connected by pipes and valves, and for the normal operation of a distillation unit other instruments for measuring the flow rate, temperature and pressure are also required. Problems which might arise during the determination and selection of such apparati and their number requires knowledge of the specific systems which must

Feedback control for distributed heat transfer mechanisms in direct-contact membrane distillation system

KAUST Repository

Eleiwi, Fadi; N'Doye, Ibrahima; Laleg-Kirati, Taous-Meriem

2015-01-01

In this paper, the problem of stabilization and production rate reference tracking for a Direct-Contact Membrane Distillation (DCMD) system is addressed. Sufficient conditions for the asymptotic and exponential stabilization for DCMD system are presented using the Gronwall-Bellman lemma and Linear Matrix Inequalities (LMIs) approaches, respectively. A nonlinear observer is then proposed to estimate the temperature distribution among the DCMD domain. This contributes to propose a reference production rate control design for the DCMD process via observer-based output control approach. Finally, numerical simulations are given to show the effectiveness of the proposed methods.

Feedback control for distributed heat transfer mechanisms in direct-contact membrane distillation system

KAUST Repository

Eleiwi, Fadi

2015-09-21

In this paper, the problem of stabilization and production rate reference tracking for a Direct-Contact Membrane Distillation (DCMD) system is addressed. Sufficient conditions for the asymptotic and exponential stabilization for DCMD system are presented using the Gronwall-Bellman lemma and Linear Matrix Inequalities (LMIs) approaches, respectively. A nonlinear observer is then proposed to estimate the temperature distribution among the DCMD domain. This contributes to propose a reference production rate control design for the DCMD process via observer-based output control approach. Finally, numerical simulations are given to show the effectiveness of the proposed methods.

Ignition delay times of Gasoline Distillation Cuts measured with Ignition Quality Tester

KAUST Repository

Naser, Nimal

2017-04-21

Tailoring fuel properties to maximize the efficiency of internal combustion engines is a way towards achieving cleaner combustion systems. In this work, the ignition properties of various gasoline fuel distillation cuts are analyzed to better understand fuel properties of the full boiling range fuel. An advanced distillation column (ADC) provides a more realistic representation of volatility characteristics, which can be modeled using equilibrium thermodynamic methods. The temperature reported is that of the liquid, as opposed to the vapor temperature in conventional ASTM D86 distillation standard. Various FACE (fuels for advanced combustion engines) gasolines were distilled and various cuts were obtained. The separated fractions were then tested in an ignition quality tester (IQT) to see the effect of chemical composition of different fractions on their ignition delay time. Fuels with lower aromatic content showed decreasing ignition delay time with increasing boiling point (i.e., molecular weight). However, fuels with higher aromatic content showed an initial decrease in ignition delay time with increasing boiling point, followed by drastic increase in ignition delay time due to fractions containing aromatics. This study also provides an understanding on contribution of different fractions to the ignition delay time of the fuel, which provides insights into fuel stratification utilized in gasoline compression ignition (GCI) engines to tailor heat release rates.

Batch distillation column modeling for quality control program

NARCIS (Netherlands)

Betlem, Bernardus H.L.

2000-01-01

For batch distillation, the dynamic composition behaviour can be described by the dominant time constant and the bottom exhaustion. Its magnitude is determined by the change of the composition distribution and is maximal when the inflection point of the molar fraction profile is located in the

Distillation of oil-bearing minerals

Energy Technology Data Exchange (ETDEWEB)

1952-05-21

In the process of distilling oil-bearing minerals such as oil shale which disintegrates during distillation, wherein the subdivided minerals are subjected to a distillation temperature in the form of a highly turbulent dense mass fluidized by an upwardly flowing gasiform medium in a distillation zone and the heat required by the distillation is supplied by burning solid distillation residue with a combustion-supporting gas in the form of a fluidized mass of solids in a separate combustion zone at a temperature substantially higher than the distillation temperature and returning solid combustion residue substantially at the higher temperature to the distillation zone. The steps of starting up the process which consists of maintaining in the distillation and combustion zones dense turbulent fluidized beds of non-disintegrating solids, circulating the non-disintegrating solids between said beds, heating the circulating solids by an auxiliary heat supply until the bed in the distillation zone has reached at least the distillation temperature, thereafter charging fresh oil-bearing minerals to the bed in the distillation zone, continuing the circulation, withdrawing solids which have passed through the combustion zone at a rate adequate to maintain a solids balance, supplying the combustion-supporting gas to the combustion zone to cause the combustion of the residue, and discontinuing the auxilary heating when sufficient heat for the distillation is being generated in the combustion zone.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1927-12-23

Oil bearing solids such as coal, tar sands, oil shales, or the like, are distilled in a current of hot gas and are first preheated to a temperature above that at which the heaviest oil fractions in the vapors are liable to condense, for example 100 to 250/sup 0/C, according to the volume of gas passing through the retort, temperature being in inverse proportion to the quantity of oxygen containing constituents in the charge. When the distillation takes place in a controlled volume of hot inert gas of 45,000 cubic feet per ton and the volume of oil recovered is about 20 gallons per ton, the material is preheated to 200 to 250/sup 0/C, when the volume of gas used is 100,000 cubic feet the preheating temperature is 150/sup 0/C. The temperatures of the retort dust extractor etc. do not fall below 100 to 150/sup 0/C until actual condensation of the oil vapor is desired. Specification 287,381 is referred to, and Specification 287,037 also is referred to in the Provisional Specification.

Proportional-integral control modes for a hydrogen isotope distillation column

International Nuclear Information System (INIS)

Kinoshita, M.; Bartlit, J.R.; Sherman, R.H.

1984-01-01

The dynamics and control of a hydrogen isotope distillation column are discussed. The proportionalintegral (PI) controller parameter setting method previously reported by one of the authors is further investigated and extended by applying the method to two different experimental control modes. The method accounts for the nonlinearity of the column to some extent and allows us to predict the unstable region or the region of the proportional-only control behavior. The method can also be applied to the cases where the measurement of the controlled variable is accompanied by a significant time lag. The mean delay time depends greatly on the controlled variable and manipulated variable chosen and the upset condition assumed, varying by over two orders of magnitude. The PI control presents great stability, and a rather long time lag is permissible in the measurement of the controlled variable if the flow rate of the top product is chosen for the manipulated variable. On the other hand, if the reflux ratio is manipulated for controlling the lightest key element in the bottom product, the great stability is no longer present and the time lag must be adequately short. Once several response curves of the controlled variable are calculated for different magnitudes of the manipulated variable upset, the parameter setting method proposed makes it possible to study how long a time lag is allowable in the measurement of the controlled variable

Distillation of oil-bearing minerals

Energy Technology Data Exchange (ETDEWEB)

1952-12-03

A process of distilling oil-bearing minerals of the type of oil shale which disintegrate during distillation consists of subjecting the subdivided minerals to a distillation temperature in the form of a highly turbulent dense mass fluidized by an upwardly flowing gasiform medium in a distillation zone and supplying the heat required for the distillation by burning solid distillation residue with a combustion-supporting gas in the form of a fluidized mass of solids in a separate combustion zone at a combustion temperature and returning solid combustion residue substantially at the combustion temperature to the distillation zone. Combustion temperature is positively maintained at a figure not exceeding 1,200/sup 0/F and at a figure which is not substantially more than 50/sup 0/F higher than the distillation temperature.

Catalytic distillation process

Science.gov (United States)

Smith, L.A. Jr.

1982-06-22

A method is described for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C[sub 4] feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

Dynamic behavior of the intensified alternative configurations for quaternary distillation

DEFF Research Database (Denmark)

Ramirez-Marquez, Cesar; Cabrera-Ruiz, Julián; Juan Gabriel Segovia-Hernandez, Juan Gabriel

2016-01-01

Process intensification emerges as an important tool in the synthesis of multicomponent distillation configurations aimed at the reduction of the energy use and capital costs. Operational and fixed costs savings coupled with simplicity and controllability design configurations appear as an essent......Process intensification emerges as an important tool in the synthesis of multicomponent distillation configurations aimed at the reduction of the energy use and capital costs. Operational and fixed costs savings coupled with simplicity and controllability design configurations appear...... value decomposition technique in all frequency domain. In order to complete the control study, the distillation schemes were subjected to closed-loop dynamic simulations. The results show that there are cases in which the intensified sequences do not only provide energy savings, but also may offer...

Development of an Exploration-Class Cascade Distillation System: Flight Like Prototype Design Status

Science.gov (United States)

Sargusingh, Miriam C.; Callahan, Michael R.

2016-01-01

The ability to recover and purify water through physiochemical processes is crucial for realizing long-term human space missions, including both planetary habitation and space travel. Because of their robust nature, distillation systems have been actively pursued as one of the technologies for water recovery. One such technology is the Cascade Distillation System (CDS) a multi-stage vacuum rotary distiller system designed to recover water in a microgravity environment. The CDS provides a similar function to the state of the art (SOA) vapor compressor distiller (VCD) currently employed on the International Space Station, but its control scheme and ancillary components are judged to be more straightforward and simpler to implement into a more reliable and efficient system. Through the Advanced Exploration Systems (AES) Life Support Systems (LSS) Project, the NASA Johnson Space Center (JSC) in collaboration with Honeywell International is developing a second generation flight forward prototype (CDS 2.0). A preliminary design fo the CDS 2.0 was presented to the project in September 2014. Following this review, detailed design of the system continued. The existing ground test prototype was used as a platform to demonstrate key 2.0 design and operational concepts to support this effort and mitigate design risk. A volumetric prototype was also developed to evaluate the packaging design for operability and maintainability. The updated system design was reviewed by the AES LSS Project and other key stakeholders in September 2015. This paper details the status of the CDS 2.0 design.

Separation of H-D mixtures by cryogenic distillation

International Nuclear Information System (INIS)

Luo Yangming; Gu Mei; Wang Heyi; Liu Jun; Fu Zhonghua; Xia Xiulong; Liu Yunnu; Weng Kuiping; Xie Bo; Ren Xingbi

2007-01-01

In this paper, separation of hydrogen-deuterium mixtures were performed on a cryogenic distillation apparatus. The results show that the D/H ratio in the reboiler reduced to 1.27x10 -2 at 120h with a flow flux of 5mol/h of the gas mixture in D/H ratio of 1.4xl0 -4 . The enrichment effect increased apparently with D/H ratio of the feeding gas. However, the deuterium content in the top of distillation column increased with the deuterium content in the reboiler, and the de-deuterium efficiencies decreased. In the full reflux experiment, the de-deuterium efficiency increased with heating power of the reboiler, and the inside pressure in the distillation column increased, too. It was necessary that suitable heating power should be chosen in order to control operation pressure in the cryogenic distillation process. (authors)

Nonlinear Lyapunov-based boundary control of distributed heat transfer mechanisms in membrane distillation plant

KAUST Repository

Eleiwi, Fadi

2015-07-01

This paper presents a nonlinear Lyapunov-based boundary control for the temperature difference of a membrane distillation boundary layers. The heat transfer mechanisms inside the process are modeled with a 2D advection-diffusion equation. The model is semi-descretized in space, and a nonlinear state-space representation is provided. The control is designed to force the temperature difference along the membrane sides to track a desired reference asymptotically, and hence a desired flux would be generated. Certain constraints are put on the control law inputs to be within an economic range of energy supplies. The effect of the controller gain is discussed. Simulations with real process parameters for the model, and the controller are provided. © 2015 American Automatic Control Council.

Design concept of control system for cryogenic distillation columns of fusion reactor

International Nuclear Information System (INIS)

Yamanishi, Toshihiko; Okuno, Kenji

1993-09-01

Control systems were designed for cryogenic distillation columns in the main fuel cycle and the breeder blanket interface systems of fusion reactors. Three basic control modes were proposed for the column whose top product was more important; the column whose bottom product is more important; and the column having a feed back stream. The key component in the important product stream was selected for each column, and the analysis method for measurement of this key component was discussed. Some of the columns need the gas chromatography as the analysis instrument of the control system. The time required for the measurement of product purity by the gas chromatography considerably affects the stability of the control system. A significant conclusion is that permissible time is about 20 min. It is possible to complete the measurement within 20 minute by the gas chromatography. The gas chromatography is applicable for the control system of the column. (author)

Separation of Process Wastewater with Extractive Heterogeneous-Azeotropic Distillation

Directory of Open Access Journals (Sweden)

Tóth András József

2016-10-01

Full Text Available The application of vapour-liquid equilibria-based separation alternatives can be extraordinarily complicated for the treatment of process wastewaters containing heterogeneous-azeotropic. Despite dissimilar successfully tested methods for separation, there is possibility to get better distillation method by enabling the separation of more and more specific process wastewater. Extractive heterogeneous-azeotropic distillation (EHAD is a new advance in treatment of fine chemical wastewater showing special features to cope with the treatment of highly non-ideal mixtures. This method combines the worth of heterogeneous-azeotropic and extractive distillations in one apparatus without addition of any extra materials. The study of the separations of ternary component process wastewater from the fine chemical industry shows both in the modelled and experimental results that EHAD can be successfully applied. The measured and modelled compositions at extreme purities, that is, close to 0% or 100%, can be different because of the inaccuracies of the modelling. This highlights the paramount importance of the experiments if special extra-fine chemicals with almost no impurities, e.g. of pharmacopoeial quality are to be produced by special distillation technique. This study expands the application of EHAD technique, this new field is the separation of process wastewaters.

Distillation apparatus for solid materials

Energy Technology Data Exchange (ETDEWEB)

Lurmann, F

1860-06-26

The distillation room is continuously charged by the charging mechanism with the material to be distilled. The distillation products pass into the chamber, where they are drawn out through the tube for purifying. The distillation residue is finally pushed out by the fresh material from the room and falls in the common room, from which it is removed through the air-tight door. In the canals enclosing the room heating gas circulates, which carries to the room the heat necessary for the distillation.

A Study on the Fabrication of Uranium-Cadmium Alloy and its Distillation Behavior

International Nuclear Information System (INIS)

Kim, Ji Yong; Ahn, Do Hee; Kim, Kwang Rag; Paek, Seung Woo; Kim, Si Hyung

2010-01-01

The pyrometallurgical nuclear fuel recycle process, called pyroprocessing, has been known as a promising nuclear fuel recycling technology. Pyroprocessing technology is crucial to advanced nuclear systems due to increased nuclear proliferation resistance and economic efficiency. The basic concept of pyroprocessing is group actinide recovery, which enhances the nuclear proliferation resistance significantly. One of the key steps in pyroprocessing is 'electrowinning' which recovers group actinides with lanthanide from the spent nuclear fuels. In this study, a vertical cadmium distiller was manufactured. The evaporation rate of pure cadmium in vertical cadmium distiller varied from 12.3 to 40.8 g/cm 2 /h within a temperature range of 773 ∼ 923 K and pressure below 0.01 torr. Uranium - cadmium alloy was fabricated by electrolysis using liquid cadmium cathode in a high purity argon atmosphere glove box. The distillation behavior of pure cadmium and cadmium in uranium - cadmium alloy was investigated. The distillation behavior of cadmium from this study could be used to develop an actinide recovery process from a liquid cadmium cathode in a cadmium distiller

A Study on the Fabrication of Uranium-Cadmium Alloy and its Distillation Behavior

Energy Technology Data Exchange (ETDEWEB)

Kim, Ji Yong [University of Science and Technology, Daejeon (Korea, Republic of); Ahn, Do Hee; Kim, Kwang Rag; Paek, Seung Woo; Kim, Si Hyung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-12-15

The pyrometallurgical nuclear fuel recycle process, called pyroprocessing, has been known as a promising nuclear fuel recycling technology. Pyroprocessing technology is crucial to advanced nuclear systems due to increased nuclear proliferation resistance and economic efficiency. The basic concept of pyroprocessing is group actinide recovery, which enhances the nuclear proliferation resistance significantly. One of the key steps in pyroprocessing is 'electrowinning' which recovers group actinides with lanthanide from the spent nuclear fuels. In this study, a vertical cadmium distiller was manufactured. The evaporation rate of pure cadmium in vertical cadmium distiller varied from 12.3 to 40.8 g/cm{sup 2}/h within a temperature range of 773 {approx} 923 K and pressure below 0.01 torr. Uranium - cadmium alloy was fabricated by electrolysis using liquid cadmium cathode in a high purity argon atmosphere glove box. The distillation behavior of pure cadmium and cadmium in uranium - cadmium alloy was investigated. The distillation behavior of cadmium from this study could be used to develop an actinide recovery process from a liquid cadmium cathode in a cadmium distiller.

27 CFR 27.40 - Distilled spirits.

Science.gov (United States)

2010-04-01

... OF THE TREASURY LIQUORS IMPORTATION OF DISTILLED SPIRITS, WINES, AND BEER Tax On Imported Distilled Spirits, Wines, and Beer Distilled Spirits § 27.40 Distilled spirits. (a) A tax is imposed on all... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Distilled spirits. 27.40...

21 CFR 184.1848 - Starter distillate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Starter distillate. 184.1848 Section 184.1848 Food... Specific Substances Affirmed as GRAS § 184.1848 Starter distillate. (a) Starter distillate (butter starter distillate) is a steam distillate of the culture of any or all of the following species of bacteria grown on...

Application of the Advanced Distillation Curve Method to the Comparison of Diesel Fuel Oxygenates: 2,5,7,10-Tetraoxaundecane (TOU), 2,4,7,9-Tetraoxadecane (TOD), and Ethanol/Fatty Acid Methyl Ester (FAME) Mixtures.

Science.gov (United States)

Burger, Jessica L; Lovestead, Tara M; LaFollette, Mark; Bruno, Thomas J

2017-08-17

Although they are amongst the most efficient engine types, compression-ignition engines have difficulties achieving acceptable particulate emission and NO x formation. Indeed, catalytic after-treatment of diesel exhaust has become common and current efforts to reformulate diesel fuels have concentrated on the incorporation of oxygenates into the fuel. One of the best ways to characterize changes to a fuel upon the addition of oxygenates is to examine the volatility of the fuel mixture. In this paper, we present the volatility, as measured by the advanced distillation curve method, of a prototype diesel fuel with novel diesel fuel oxygenates: 2,5,7,10-tetraoxaundecane (TOU), 2,4,7,9-tetraoxadecane (TOD), and ethanol/fatty acid methyl ester (FAME) mixtures. We present the results for the initial boiling behavior, the distillation curve temperatures, and track the oxygenates throughout the distillations. These diesel fuel blends have several interesting thermodynamic properties that have not been seen in our previous oxygenate studies. Ethanol reduces the temperatures observed early in the distillation (near ethanol's boiling temperature). After these early distillation points (once the ethanol has distilled out), B100 has the greatest impact on the remaining distillation curve and shifts the curve to higher temperatures than what is seen for diesel fuel/ethanol blends. In fact, for the 15% B100 mixture most of the distillation curve reaches temperatures higher than those seen diesel fuel alone. In addition, blends with TOU and TOD also exhibited uncommon characteristics. These additives are unusual because they distill over most the distillation curve (up to 70%). The effects of this can be seen both in histograms of oxygenate concentration in the distillate cuts and in the distillation curves. Our purpose for studying these oxygenate blends is consistent with our vision for replacing fit-for-purpose properties with fundamental properties to enable the development of

Regenerative adsorption distillation system

KAUST Repository

Ng, Kim Choon; Thu, Kyaw; Amy, Gary; Chunggaze, Mohammed; Al-Ghasham, Tawfiq

2013-01-01

There is provided a regenerative adsorption distillation system comprising a train of distillation effects in fluid communication with each other. The train of distillation effects comprises at least one intermediate effect between the first and last distillation effects of the train, each effect comprising a vessel and a condensing tube for flow of a fluid therein. The system further comprises a pair of adsorption-desorption beds in vapour communication with the last effect and at least one intermediate effect, wherein the beds contain an adsorbent that adsorbs vapour from the last effect and transmits desorbed vapour into at least one of the intermediate effect.

Regenerative adsorption distillation system

KAUST Repository

Ng, Kim Choon

2013-12-26

There is provided a regenerative adsorption distillation system comprising a train of distillation effects in fluid communication with each other. The train of distillation effects comprises at least one intermediate effect between the first and last distillation effects of the train, each effect comprising a vessel and a condensing tube for flow of a fluid therein. The system further comprises a pair of adsorption-desorption beds in vapour communication with the last effect and at least one intermediate effect, wherein the beds contain an adsorbent that adsorbs vapour from the last effect and transmits desorbed vapour into at least one of the intermediate effect.

Distillation of bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Seguin, M

1875-02-16

The retort with its accessories constitutes a distillation apparatus for shale composed of a cylindrical, vertical, fixed, tubular, and of ring form metal retort. Also it is comprised of a special hearth of large dimensions in the form of a circular pocket receiving from the retort as heating agent the distilled shale and emitting by radiation the heat that makes the distillation apparatus for the shale act.

Electrical Thermal Network for Direct Contact Membrane Distillation Modeling and Analysis

KAUST Repository

Karam, Ayman M.

2015-02-04

Membrane distillation is an emerging water distillation technology that offers several advantages compared to conventional water desalination processes. Although progress has been made to model and understand the physics of the process, many studies are based on steady-state assumptions or are computationally not appropriate for real time control. This paper presents the derivation of a novel dynamical model, based on analogy between electrical and thermal systems, for direct contact membrane distillation (DCMD). The proposed model captures the dynamics of temperature distribution and distilled water flux. To demonstrate the adequacy of the proposed model, validation with transient and steady-state experimental data is presented.

Distilling shale and coal

Energy Technology Data Exchange (ETDEWEB)

Edwards, H; Young, G

1923-01-09

In a process of recovering oil from shale or coal the material is ground and may be subjected to a cleaning or concentrating process of the kind described in Specification 153,663 after which it is distilled in a furnace as described in Specification 13,625/09 the sections of the furnace forming different temperature zones, and the rate of the passage of the material is regulated so that distillation is complete with respect to the temperature of each zone, the whole distillation being accomplished in successive stages. The vapors are taken off at each zone and superheated steam may be passed into the furnace at suitable points and the distillation terminated at any stage of the process.

Herbal distillates: A new era of grape marc distillates with enriched antioxidant profile.

Science.gov (United States)

Andreou, Vasiliki; Strati, Irini F; Fotakis, Charalambos; Liouni, Maria; Zoumpoulakis, Panagiotis; Sinanoglou, Vassilia J

2018-07-01

Grape marc distillates are traditional alcoholic beverages, produced mostly in the Mediterranean countries. The present study proposes the enrichment of a Greek traditional grape marc distillate (tsikoudia) with selected herbs to enhance its natural antioxidants and functional properties. Total phenolic content, the antiradical and antioxidant activities, as well as the phenolic and sugar profiles using NMR and FT-IR spectroscopy were evaluated. The enrichment of distillates with Syzygium aromaticum L., Jasminum officinale L. and Eucalyptus globulus Labill. exhibited the highest total phenolic content as well as the highest antioxidant and antiradical activities, whereas the lowest values were observed with Hippophae rhamnoides L. and Lycium Barbarum Mill. The implementation of NMR and FT-IR spectroscopies attested to the presence of phenolic compounds and of specific carbohydrates in herbal distillates, postulating their migration from selected herbal species to tsikoudia and probably contributing to their organoleptic characteristics. The target of this approach leads to new added-value distillates with enhanced characteristics. Copyright © 2018 Elsevier Ltd. All rights reserved.

Hybrid wind-power-distillation plant

Directory of Open Access Journals (Sweden)

Ninić Neven

2012-01-01

Full Text Available This paper reports and elaborates on the idea of a solar distiller and an offshore wind power plant operating together. The subject under discussion is a single-stage solar distillation plant with vaporization, using adiabatic expansion in the gravitational field inside a wind power plant supporting column. This scheme divides investment costs for electric power and distillate production. In the region of the Adriatic Sea, all electric power produced could be “converted” to hydrogen using less than 10% of the distillate produced.

Zone distillation: a new purification method

International Nuclear Information System (INIS)

Kravchenko, A.I.

2011-01-01

The features of zone distillation (with zone melting of refined material and with pulling of condensate) as a new purification method are shown. The method is based on similarity of equations of distillation and crystallization refining. The analogy between some distillation and condensation methods (particularly between zone distillation and zone recrystallization) is should up

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1948-08-03

A continuous method of distilling shale to produce valuable hydrocarbon oils is described, which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors containing shale fines from the zone, mixing sufficient fresh cold shale with the hydrocarbon vapors to quench the same and to cause condensation of the higher boiling constituents thereof, charging the mixture of vapors, condensate, and cold shale to a separation zone where the shale is maintained in a fluidized condition by the upward movement of the hydrocarbon vapors, withdrawing condensate from the separation zone and recycling a portion of the condensate to the top of the separation zone where it flows countercurrent to the vapors passing therethrough and causes shale fines to be removed from the vapors by the scrubbing action of the condensate, recovering hydrocarbon vapors and product vapors from the separation zone, withdrawing preheated shale from the separation zone and charging it to a shale distillation zone.

Destructive distillation: oils

Energy Technology Data Exchange (ETDEWEB)

West, J; Glover, S

1918-01-31

Canned and other coals are destructively distilled in continuously operated vertical retorts which at their upper portions are maintained at temperatures suitable for low temperature oil distillation such as about 700/sup 0/C, and at their lower portions the temperature is higher and such as to be suitable for the production of gas, e.g., about 1400/sup 0/C. Superheated steam is introduced into the lower portion of the retort, preferably by means of the arrangement described in Specification 120,458, and this is converted into blue water gas which assists the distillation in the center of the coal charge. The retorts are preferably such as are described in Specifications 2663/07 and 7757/14.

Thermo-economic performance of inclined solar water distillation systems

Directory of Open Access Journals (Sweden)

Agboola Phillips O.

2015-01-01

Full Text Available This study investigates the thermo-economic performance of different configurations of inclined solar water desalination for parameters such as daily production, efficiency, system cost and distilled water production cost. The four different configurations considered for this study are as follows; 1. Inclined solar water distillation with bare absorber plate (IISWD with daily production of 5.46 kg/m2 day and daily efficiency of 48.3%. 2. Inclined solar water distillation with wick on absorber plate (IISWDW with daily production of 6.41kg/m2 day and daily efficiency 50.3%. 3. Inclined solar water distillation with wire mesh on absorber plate (IISWDWM with daily production n of 3.03 kg/m2 day and daily efficiency 32.6%. 4. Inclined solar water distillation with bare absorber plate (ISWD. (Control System with daily production of 3.25 kg/m2 day and daily efficiency of 40.1%. The systems potable water cost price ranges from 0.03 $/L for IISWDW to 0.06$/L for IISWDWM System. All the systems are economically and technically feasible as a solar distillation system for potable water in Northern Cyprus. The price of potable water from water vendors/hawkers ranges from 0.11-0.16 $/L. It is more economically viable to have the rooftop inclined solar water desalination system than procuring potable water from vendors.`

Control system implementation for a complex low inventory cryogenic distillation system for Princeton TFTR

International Nuclear Information System (INIS)

Busigin, A.; Busigin, C.J.; Adamek, F.; Woodall, K.B.; Robins, J.R.; Bellamy, D.G.; Fong, C.; Kalyanam, K.M.; Sood, S.K.

1995-01-01

The TFTR Tritium Purification System (TPS) is based on a Pd/Ag diffuser front-end for separating hydrogen isotopes from inert gas, and a four column cryogenic distillation cascade for separation of hydrogen isotopes. The system has a tritium inventory of approximately 0.5 g while successfully producing pure H 2 , D 2 and T 2 products. The system has recently been built and successfully commissioned with protium and deuterium. Stable automatic control of the cascade has been demonstrated even when feed rate and composition varied. The automatic control scheme maintained stable column inventories and excellent H 2 and D 2 product qualities. The control system employed new control concepts such as real time analysis of mid-column composition using temperature and pressure data for feedback control. Very stable column inventory control was achieved by automatic adjustment of inter-column flows (feed forward and feed back). This paper discusses the control system design and presents performance test results. (orig.)

Elementary Analysis of Petroleum Distillates by Gc-Aed: Validation and Application to the Calculation of Distillation Profile Properties

Directory of Open Access Journals (Sweden)

Baco F.

1999-07-01

Full Text Available This article describes the development of elementary analysis in the distillation profile of petroleum cuts by gas phase chromatography-atomic emission detection (GC-AED coupling and shows the application perspectives to characterisation of middle distillates of a piece of information unheard of until now on a routine basis. The performances of the analytical assembly used have been studied for carbon, hydrogen, sulphur and nitrogen analysis. Simulated distillation, a gas phase chromatography analysis which enables determining the weight percentage of distilled matter in relation to the boiling point of petroleum cuts, has been adapted to GC-AED coupling. We have developed a method giving access to three types of information: global elementary composition, simulated distillation and elementary composition in distillation profile, i. e. by fraction (% of the distilled product. The analysis of the atmospheric distillates has been assessed in terms of precision and bias for these various types of information. The validation was carried out notably by comparison with the results obtained using reference analytical methods, on preparative distillation cuts of representative samples. The application of GC-AED to characterisation of distillates is discussed, in particular for classification purposes and for predicting petroleum properties in the distillation profile. The cetane number of gas oils was taken as an example to illustrate the latter application.

Distilling shale and the like

Energy Technology Data Exchange (ETDEWEB)

Gee, H T.P.

1922-02-23

In distilling shale or like bituminous fuels by internal heating with hot gas obtained by the gasifying of the shale residues with air or steam or a mixture of these, the amount and temperature of the gaseous distilling medium is regulated between the gasifying and the distilling chambers, by the introduction of cold gas or air.

Distillation with labelled transition systems

DEFF Research Database (Denmark)

Hamilton, Geoffrey William; Jones, Neil

2012-01-01

In this paper, we provide an improved basis for the " distillation" program transformation. It is known that superlinear speedups can be obtained using distillation, but cannot be obtained by other earlier automatic program transformation techniques such as deforestation, positive supercompilation...... and partial evaluation. We give distillation an improved semantic basis, and explain how superlinear speedups can occur....

Transient period analysis of a distillation column using a control approach with distributed heating; Analise do periodo transiente de uma coluna de destilacao usando abordagem de controle com aquecimento distribuido

Energy Technology Data Exchange (ETDEWEB)

Werle, Leandro O.; Steinmacher, Fernanda R.; Marangoni, Cintia; Araujo, Pedro H.H de; Machado, Ricardo A.F.; Sayer, Claudia [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2008-07-01

The distillation process is widely used in oil refineries. The non-linear behavior, the coupling between variables and the high time constants, associated to the response delay, result in long transient periods operating out of the desired conditions, obtaining out of specification products. Even with several researches in more and more complex control approaches, few works approached the aspect of transient minimization. Moreover, the control of distillation columns is carried out centralized at the bottom and the top. In the present work the effect of the distributed control is evaluated, through the electric resistance located on an intermediate tray of the column. The objective of the work is reducing the operation transients when a disturbance is applied. For the current study, experiments have been carried out in a pilot distillation unit composed of 13 trays and instrumented in fieldbus, processing an ethanol-water mixture. Step disturbances of 50% in the feeding flow rate of have been carried out. The comparison of the results showed that the introduction of the distributed heating throughout the column allows faster dynamics, revealing itself as a valid option for the transient reduction. (author)

Design and control of an alternative distillation sequence for bioethanol purification

DEFF Research Database (Denmark)

Errico, Massimiliano; Ramírez-Márquez, César; Torres Ortega, Carlo Edgar

2015-01-01

BACKGROUND: Bioethanol is a green fuel considered to be a sustainable alternative to petro-derived gasoline. The transport sector contributes significantly to carbon dioxide emission and consequently has a negative impact on the air quality and is responsible for the increase of the greenhouse...... separation is presented. The steady state performance and the dynamic beavior are analyzed compared with the classical configuration reported in the literature. RESULTS: Ethanol-water azeotropic separation represents a challenge for bioethanol purification. Usually a three column sequence is used to obtain...... fuel grade bioethanol by extractive distillation. In order to reduce bioethanol purification cost a two column separation sequence is proposed. This configuration shows a 10% saving in capital costs together with higher ethanol recovery and better control properties compared with the classical three...

Experimental Verification of Dynamic Operation of Continuous and Multivessel Batch Distillation

Energy Technology Data Exchange (ETDEWEB)

Wittgens, Bernd

1999-07-01

This thesis presents a rigorous model based on first principles for dynamic simulation of the composition dynamics of a staged high-purity continuous distillation columns and experiments performed to verify it. The thesis also demonstrates the importance of tray hydraulics to obtain good agreement between simulation and experiment and derives analytic expressions for dynamic time constants for use in simplified and vapour dynamics. A newly developed multivessel batch distillation column consisting of a reboiler, intermediate vessels and a condenser vessel provides a generalization of previously proposed batch distillation schemes. The total reflux operation of this column was presented previously and the present thesis proposes a simple feedback control strategy for its operation based on temperature measurements. The feasibility of this strategy is demonstrated by simulations and verified by laboratory experiments. It is concluded that the multivessel column can be easily operated with simple temperature controllers, where the holdups are only controlled indirectly. For a given set of temperature setpoints, the final product compositions are independent of the initial feed composition. When the multivessel batch distillation column is compared to a conventional batch column, both operated under feedback control, it is found that the energy required to separate a multicomponent mixture into highly pure products is much less for the multivessel system. This system is also the simplest one to operate.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Young, W

1881-04-12

Destructive distillation of shale for the manufacture of mineral oil and ammonia is described. The retorts are arranged in benches, each retort being placed over its own combustion chamber into which the spent shale is discharged and consumed in heating the next charge as described in Specification No. 1578, A. D. 1880. Two forms of retorts are shown, each consisting of two retorts placed above and communicating with one another, the upper being employed to distill the oil at a low red heat, and the lower to eliminate the nitrogen in the form of ammonia at a much higher temperature. The retorts are divided by a sliding damper and have an outlet for the passage of the products placed at the junction. The retorts have an outlet at the top for the escape of the products. Each retort has an opening closed by a cover for charging and a door for discharging. The products of combustion from the combustion chambers pass through ports to a chamber surrounding the lower retorts and thence through ports in the division wall controlled by dampers into the chamber surrounding the upper retorts, whence they pass through flues to the chimney. Around the bottom of each retort are openings communicating with a chamber to which steam is admitted through a valve from a pipe preferably placed in a coil in the flue.

Low temperature destructive distillation

Energy Technology Data Exchange (ETDEWEB)

1938-07-05

A process is given and apparatus is described for the destructive distillation at low temperature of coal, oil shale, and the like by subjection to the action of a stream of hot gases or superhearted steam, flowing in a closed circuit. Subsequent treatment of the distillation residues with a gas stream containing oxygen results in combustion of the carbon-containing material therein brings to a high temperature the solid residue, in which the process comprises subsequently contacting the hot solid residue with the fluid stream effecting the distillation.

Distilling bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Forrest, C N; Hayden, H P

1926-12-28

Bituminous materials such as heavy asphaltic residues from petroleum distillation or natural bitumens such as gilsonite, grahamite, etc. are distilled in presence of a carrier consisting of pieces of inert refractory material and by the heat generated by combustion of the coke which remains on the carrier after distillation. A vertical cylindrical retort, in which a wood and coal fire is first made, is charged with an inert refractory substance such as pumice stone, broken firebrick, burnt fire clay, carborundum, ash, etc. mixed with a bituminous substance, which, if fusible, may be melted and added in a rotary drum. The mixture passes downwards through the retort, first through regions in which the hydrocarbons are distilled and cracked and then through a region in which the remaining carbon is burnt by a limited supply of air and steam admitted through a grate. The inert material is discharged through a water seal and used again. Vapors, withdrawn from the retort though an outlet, pass through a heat intercharger and separator and are treated with a spray of sulfuric acid to separate ammonia in a scrubber, with water sprays to condense oil in scrubbers, and with oil in a scrubber.

Cyclic distillation technology - A mini-review

DEFF Research Database (Denmark)

Bîldea, Costin Sorin; Pătruţ, Cătălin; Jørgensen, Sten Bay

2016-01-01

Process intensification in distillation systems has received much attention during the pastdecades, with the aim of increasing both energy and separation efficiency. Varioustechniques, such as internal heat-integrated distillation, membrane distillation, rotating packedbed, dividing-wall columns...

A novel back-up control structure to manage nonroutine steam upsets in industrial methanol distillation columns

DEFF Research Database (Denmark)

Udugama, Isuru A.; Zander, Cornina; Mansouri, Seyed Soheil

2017-01-01

Industrial methanol production plants have extensive heat integration to achieve energy efficient operations where steam generated from these heat integration operations are used to provide reboiler duty for methanol distillation columns that purify crude methanol produced into industrial AA grade...... supervisory layer to control the column during these non-routine process upsets. These control schemes were tested against realistic reboiler duty disturbances that can occur in an industrial process. The tests revealed that both the MPC and supervisory systems control structures are able to regulate...... the process, even during sudden drops in reboiler duty. However, the cost of implementation and the relative simplicity will likely favour the implementation of the supervisory control structure in an industrial environment....

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Young, W

1877-03-29

The method consists in agitating or circulating the distillation products inside the retort by means of jets of gas, steam, or vapor, or by means of reciprocating pistons; condensing certain of the heavy hydrocarbons; sealing or luting the doors of retorts or distilling-vessels; and conducting the distillation for the manufacture of oil so that the charging or discharging doors may be fitted with self-sealing lids. Several arrangements are shown and described; a single horizontal retort is divided into two compartments by a perforated plate which supports the coal, shale, or other bituminous substance, beneath which a piston is reciprocated or a jet of steam, gas, or vapor injected; a vertical retort is fitted with a central tube into which steam, gas, or vapor is injected, or it may be divided into two compartments and the jet injected into one of these; a pair of vertical retorts are connected by a horizontal passage at the top and bottom, and into the upper one steam, gas, or vapor is injected, or the lower one is fitted with a piston.

Evaluation of chemical composition of defect wine distillates

OpenAIRE

Mihaljević Žulj, Marin; Posavec, Barbara; Škvorc, Melanija; Tupajić, Pavica

2016-01-01

The aim of this study was to evaluate the chemical composition of the distillate obtained from wine with off-flavour. The chemical composition of wine distillates obtained by distillation of Chardonnay wine with oxidation off-flavour was investigated. Distillation of wine was carried out using a simple distillation pot still by double distillation and separation the different portion of the first fraction. Volatile compounds of wine and wine distillates (acetaldehyde, ethyl acetate, methanol ...

Distilling hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

Turner, C

1917-11-23

In the fractional or destructive distillation of hydrocarbon oils or other liquids, the pressure in the still is raised and lowered alternately. The still is closed to raise the pressure, and is opened to lower the pressure rapidly solely by expansion of the vapors. The operation is effected without intermittent cooling, except such as may occur during the lowering of the pressure. In distilling hydrocarbon oil, pressure steam is blown into the oil until the pressure reaches 5 lb/in./sup 2/. The vapor outlet is then opened until the pressure falls to 2 lb/in./sup 2/, whereupon the vapor outlet is closed and steam is again admitted. The operation is continued until the steam, which is of 20 lb pressure, no longer effects distillation; after this stage, superheated steam is used.

Cyclic distillation technology - A mini-review

NARCIS (Netherlands)

Bîldea, Costin Sorin; Pătruţ, Cătălin; Jørgensen, Sten Bay; Abildskov, Jens; Kiss, Anton A.

2016-01-01

Process intensification in distillation systems has received much attention during past decades, with the aim of increasing both energy and separation efficiency. Various techniques, such as internal heat-integrated distillation, membrane distillation, rotating packed bed, dividing-wall columns and

Analysis of Multi-Loop Control Structures of Dividing-Wall Distillation Columns Using a Fundamental Model

Directory of Open Access Journals (Sweden)

Salvador Tututi-Avila

2014-02-01

Full Text Available Dividing-wall columns (DWCs have significant potential as energy-efficient processes for the separation of multicomponent mixtures. However, in addition to an efficient steady state design, dynamics and control also play a major part for the success of a technology. This is especially so for complex distillation systems. This paper investigates the dynamics of a dividing wall column used for the separation of ternary mixtures. A detailed dynamic first principles-based model of the column I s developed in gPROMS. The model is used to generate data used for control loop pairing via the Relative Gain Array (RGA, and controller parameters are found by using Internal Model Control (IMC tuning. The best control structures for DWC systems, involving four different ternary mixtures, and two different feed compositions for each mixture, are investigated.

27 CFR 19.322 - Distillates containing extraneous substances.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Distillates containing... Distillates containing extraneous substances. (a) Use in production. Distillates containing substantial... produced. Distillates removed from the distilling system under the provisions of this paragraph shall be...

Improvement of solar ethanol distillation using ultrasonic waves

Directory of Open Access Journals (Sweden)

Jaruwat Jareanjit

2016-08-01

Full Text Available This report presents a study on the use of ultrasonic waves in solar ethanol distillation to investigate the performance of ultrasonic waves at a frequency of 30 kHz and at 100 Watts that were installed in the inlet area of a 10-litre distillation tank. Based on the non-continuous distillation process (batch distillation, the experiment demonstrated that using ultrasonic waves in solar ethanol distillation caused the average concentration of hourly distilled ethanol to be higher than that of a normal system (solar ethanol distillation without ultrasonic wave at the same or higher distillation rate and hourly distillation volume. The ultrasonic wave was able to enhance the separation of ethanol from the solution (water-ethanol mixture through solar distillation. The amount of pure ethanol product from each distilled batch was clearly larger than the amount of product obtained from a normal system when the initial concentration of ethanol was lower than 50%v/v (% by volume, where an average of approximately 40% and 20% are obtained for an initial ethanol concentration of 10%v/v and 30%v/v, respectively. Furthermore, the distillation rate varied based on the solar radiation value.

40 CFR 1065.703 - Distillate diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Distillate diesel fuel. 1065.703... Standards § 1065.703 Distillate diesel fuel. (a) Distillate diesel fuels for testing must be clean and... distillate diesel fuels: (1) Cetane improver. (2) Metal deactivator. (3) Antioxidant, dehazer. (4) Rust...

Method of distillation of alum shale

Energy Technology Data Exchange (ETDEWEB)

Hultman, G H

1920-02-03

A method is given of distilling alum shale by means of preheated gases obtained from the process of distillation in which the gases are circulating within a system consisting of the retort, the condensation apparatus, and generator, each separate. It is characterized by leading the gases produced during the distillation through a condensation apparatus for separation of the condensable products, such as oil, benzene, ammonia, and sulfur, and the noncondensable gases are conveyed through one or more heated generators that have been charged with residue from the process of distillation (any superfluous amount of gas formed during the process being released). The heated gases are thereupon passed to the retort for completion of the distillation process.

76 FR 71309 - Notice of Intent To Suspend the Distillers Co-Products Survey and All Associated Reports

Science.gov (United States)

2011-11-17

... Distillers Co-Products Survey and All Associated Reports AGENCY: National Agricultural Statistics Service... Distillers Co- Products survey currently approved under docket 0535-0247. FOR FURTHER INFORMATION CONTACT... . SUPPLEMENTARY INFORMATION: Title: Suspension of Distillers Co-Products Survey. OMB Control Number: 0535-0247...

27 CFR 28.280 - Distilled spirits and wines.

Science.gov (United States)

2010-04-01

... departure of the aircraft, and the brand, kind, and quantity of distilled spirits or wines. Where the... shall be retained by the airline. (Approved by the Office of Management and Budget under control number...

Method of distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, E G.T.

1919-11-12

A method is described of dry distillation of bituminous materials by leading warm combustible gases, mixed or not mixed with steam, through the distillation chamber in direct contact with the materials, during which process the distillation chamber may be heated by other means. It is characterized by the mixture of distillation products (formed by the vapors produced by heating the raw materials) and the gas (circulating gas) used for heating in the process, being led through coolers or similar contrivances, in order to separate through condensation the greater part of the content of the products or materials condensable at ordinary temperatures, and also to recover as much as possible of the highly volatile oils in the gas. Thereafter the gas is split, one part is, without further cleaning, and led through the distillation chamber, after this gas has been reheated in suitable apparatus. The other part (surplus gas), which in volume corresponds approximately to the new-formed distillation gases, is treated according to known methods for the extraction of the remaining products of the distillation, such as volatile oils, ammonia, methyl alcohol, sulfuretted hydrogen, and others. The patent contains three other claims.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Newton, A V

1856-04-22

In order to obtain, at the first distillation, from coal, shale, and bituminous substances an oil sufficiently pure for illuminating and other purposes, the material broken into very small pieces and placed on the bottom of the retort, is evenly covered with common sand, about four times greater in weight than the weight of the coal. The coal and sand are then gradually raised to a temperature of 212/sup 0/F. Steam containing carbonaceous impurities first passes to the condenser, and subsequently oil, which rises to the surface of the water in the receiving-vessel. When some bituminous substances are employed, the temperature, after oil ceases to come over, may be gradually raised until the oil produced ceases to be pure. Most kinds of clay and earth, chalk, gypsum, black oxide of manganese, plumbago, or charcoal may be used separately, in combination, or with added chemicals, instead of sand as the medium for filtering the gas or vapor from which the oil is formed. Either the oil obtained by the first distillation or oils obtained by other means may be rectified by distilling with sand.

Distillation of hydrogen isotopes for polarized HD targets

Energy Technology Data Exchange (ETDEWEB)

Ohta, T., E-mail: takeshi@rcnp.osaka-u.ac.jp [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Bouchigny, S. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); CEA LIST, BP6-92265 Fontenay-aux-Roses, CEDEX (France); Didelez, J.-P. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); Fujiwara, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Fukuda, K. [Kansai University of Nursing and Health Sciences, Shizuki Awaji 656-2131 (Japan); Kohri, H.; Kunimatsu, T.; Morisaki, C.; Ono, S. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Rouille, G. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); Tanaka, M. [Kobe Tokiwa University, Ohtani-cho 2-6-2, Nagata, Kobe 653-0838 (Japan); Ueda, K.; Uraki, M.; Utsuro, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Wang, S.Y. [Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China); Department of Physics, National Kaohsiung Normal University, Kaohsiung 824, Taiwan (China); Yosoi, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan)

2012-02-01

We have developed a new cryogenic distillation system to purify Hydrogen-Deuteride (HD) gas for polarized HD targets in LEPS experiments at SPring-8. A small amount of ortho-H{sub 2} ({approx}0.01%) in the HD gas plays an important role in efficiently polarizing the HD target. Since there are 1-5% impurities of H{sub 2} and D{sub 2} in commercially available HD gases, it is necessary to purify the HD gas up to {approx}99.99%. The distillation system is equipped with a cryogenic distillation unit filled with many small stainless steel cells called 'Heli-pack'. The distillation unit consists of a condenser part, a rectification part, and a reboiler part. The unit is kept at the temperature of 17-21 K. The Heli-pack has a large surface area that makes a good contact between gases and liquids. An amount of 5.2 mol of commercial HD gas is fed into the distillation unit. Three trials were carried out to purify the HD gas by changing temperatures (17.5 K and 20.5 K) and gas extraction speeds (1.3 ml/min and 5.2 ml/min). The extracted gas was analyzed using a gas analyzer system combining a quadrupole mass spectrometer with a gas chromatograph. One mol of HD gas with a purity better than 99.99% has been successfully obtained for the first time. The effective NTP (Number of Theoretical Plates), which is an indication of the distillation performances, is obtained to be 37.2{+-}0.6. This value is in good agreement with a designed value of 37.9. The HD target is expected to be efficiently polarized under a well-controlled condition by adding an optimal amount of ortho-H{sub 2} to the purified HD gas.

Process of distilling heavy hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1929-12-03

This invention has for its object the distillation of heavy liquid hydrocarbons for the purpose of obtaining lighter hydrocarbons stable and immediately salable for fuels in combustion motors. The process is distinguished by the fact that the heavy hydrocarbon is distilled by means of heating to a temperature in keeping with the nature of the material to be treated up to 350/sup 0/C under pressure or without pressure the distillation being carried out on catalysts containing successively nickel, copper, and iron (3 parts of nickel, 1 part of copper, and 1 part of iron), the vapors produced by this distillation being exposed in turn to the action of catalysts of the same nature and in the same proportion.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bell, T

1863-09-14

Shales and other bituminous minerals are distilled in horizontal retorts arranged side by side and with furnaces beneath their front ends. The furnace gases pass, preferably through a brickwork grating, into spaces between the retorts and beneath a horizontal partition towards the back ends. They return above the partition to the front of the retorts, and finally enter a horizontal flue leading to a chimney. The front end of each retort is fitted with a hopper for charging and with a door for discharging. The products of distillation pass through perforated partitions inside the retorts and are conveyed away by pipes at the back.

Determination of methanol in Iranian herbal distillates.

Science.gov (United States)

Shirani, Kobra; Hassani, Faezeh Vahdati; Azar-Khiavi, Kamal Razavi; Moghaddam, Zohreh Samie; Karimi, Gholamreza

2016-06-01

Herbal distillates have been used as beverages, for flavoring, or as phytomedicines in many countries for a long time. Recently, the occurrence of blindness after drinking herbal distillates has created concerns in Iran. The aim of this study was to determine the concentrations of methanol in herbal distillates produced in Iran. Eighty-four most commonly used herbal distillates purchased from herbal distillate factories were analyzed for methanol contents by gas chromatography and flame ionization detection, with ethanol as internal standard. In 15 herbal distillates, the methanol concentration was below the limit of quantitation. The methanol concentrations in all samples ranged from 43 to 277 mg/L. Forty-five samples contained methanol in excess of the Iranian standard. The maximum concentration was found in an herbal distillate of Mentha piperita (factory E) (277±12), and the minimum in a distillate of Carum carvi (factory B) (42.6 ± 0.5). Since the 45 Iranian herbal distillates containing methanol levels were beyond the legal limits according to the Iranian standard, it seems necessary to monitor the amount of methanol and give a warning to watch out for the latent risk problem of methanol uptake, and establish a definitive relationship between the degree of intoxication observed and the accumulation of methanol in the blood.

Source book for planning nuclear dual-purpose electric/distillation desalination plants

International Nuclear Information System (INIS)

Reed, S.A.

1981-02-01

A source book on nuclear dual-purpose electric/distillation desalination plants was prepared to assist government and other planners in preparing broad evaluations of proposed applications of dual-purpose plants. The document is divided into five major sections. Section 1 presents general discussions relating to the benefits of dual-purpose plants, and spectrum for water-to-power ratios. Section 2 presents information on commercial nuclear plants manufactured by US manufacturers. Section 3 gives information on distillation desalting processes and equipment. Section 4 presents a discussion on feedwater pretreatment and scale control. Section 5 deals with methods for coupling the distillation and electrical generating plants to operate in the dual mode

Source book for planning nuclear dual-purpose electric/distillation desalination plants

Energy Technology Data Exchange (ETDEWEB)

Reed, S.A.

1981-02-01

A source book on nuclear dual-purpose electric/distillation desalination plants was prepared to assist government and other planners in preparing broad evaluations of proposed applications of dual-purpose plants. The document is divided into five major sections. Section 1 presents general discussions relating to the benefits of dual-purpose plants, and spectrum for water-to-power ratios. Section 2 presents information on commercial nuclear plants manufactured by US manufacturers. Section 3 gives information on distillation desalting processes and equipment. Section 4 presents a discussion on feedwater pretreatment and scale control. Section 5 deals with methods for coupling the distillation and electrical generating plants to operate in the dual mode.

Nonlinear observer-based Lyapunov boundary control of distributed heat transfer mechanisms for membrane distillation plant

KAUST Repository

Eleiwi, Fadi

2016-09-19

This paper presents a nonlinear observer-based Lyapunov control for a membrane distillation (MD) process. The control considers the inlet temperatures of the feed and the permeate solutions as inputs, transforming it to boundary control process, and seeks to maintain the temperature difference along the membrane boundaries around a sufficient level to promote water production. MD process is modeled with advection diffusion equation model in two dimensions, where the diffusion and convection heat transfer mechanisms are best described. Model analysis, effective order reduction and parameters physical interpretation, are provided. Moreover, a nonlinear observer has been designed to provide the control with estimates of the temperature evolution at each time instant. In addition, physical constraints are imposed on the control to have an acceptable range of feasible inputs, and consequently, better energy consumption. Numerical simulations for the complete process with real membrane parameter values are provided, in addition to detailed explanations for the role of the controller and the observer. (C) 2016 Elsevier Ltd. All rights reserved.

Tritium Isotope Separation Using Adsorption-Distillation Column

International Nuclear Information System (INIS)

Fukada, Satoshi

2005-01-01

In order to miniaturize the height of a distillation tower for the detritiation of waste water from fusion reactors, two experiments were conducted: (1) liquid frontal chromatography of tritium water eluting through an adsorption column and (2) water distillation using a column packed with adsorbent particles. The height of the distillation tower depends on the height equivalent to a theoretical plate, HETP, and the equilibrium isotope separation factor, α H-T equi . The adsorption action improved not only HETP but also α H-T equi . Since the adsorption-distillation method proposed here can shorten the tower height with keeping advantages of the distillation, it may bring an excellent way for miniaturizing the distillation tower to detritiate a large amount of waste water from fusion reactors

Active solar distillation - A detailed review

Energy Technology Data Exchange (ETDEWEB)

Sampathkumar, K.; Pitchandi, P. [Department of Mechanical Engineering, Tamilnadu College of Engineering, Coimbatore 641659, Tamilnadu (India); Arjunan, T.V. [Department of Automobile Engineering, PSG College of Technology, Coimbatore 641004, Tamilnadu (India); Senthilkumar, P. [Department of Mechanical Engineering, KSR College of Engineering, Tiruchengode 637215, Tamilnadu (India)

2010-08-15

All over the world, access to potable water to the people are narrowing down day by day. Most of the human diseases are due to polluted or non-purified water resources. Even today, under developed countries and developing countries face a huge water scarcity because of unplanned mechanism and pollution created by manmade activities. Water purification without affecting the ecosystem is the need of the hour. In this context, many conventional and non-conventional techniques have been developed for purification of saline water. Among these, solar distillation proves to be both economical and eco-friendly technique particularly in rural areas. Many active distillation systems have been developed to overcome the problem of lower distillate output in passive solar stills. This article provides a detailed review of different studies on active solar distillation system over the years. Thermal modelling was done for various types of active single slope solar distillation system. This review would also throw light on the scope for further research and recommendations in active solar distillation system. (author)

THE EFFECT OF DISTILLATE STORING DISTILLED FROM FRUCTOSE SYRUPS TOWARD ITS ACETALDEHYDE CONCENTRATION MEASURED BY GAS CHROMATOGRAPHY

Directory of Open Access Journals (Sweden)

Maria Monica Sianita Basukiwardojo

2010-06-01

Full Text Available Acetaldehyde is a compound of aldehyde group that is very volatile and toxic. This compound can be found in fructose syrups used in carbonate beverages. The syrups had been distilled then analysed using gas chromatography. The concentration of acetaldehyde was 289.78 g/g in the distillates kept for one week, 295.30 g/g in those kept for two weeks, 429.45 g/g in those kept for three weeks, and 449.38 g/g in those kept for four weeks. The optimum column temperature was programmed with initial temperature of 40 oC held on for four minutes, then increasing by 40 oC/minute to 200 oC. It can be concluded that the longer the distillates have been kept, the greater the concentration of acetaldehyde in the distillates. A further research to investigate the present of microbe in the distillates and the effect of pH should be conducted   Keywords: acetaldehyde, fructose syrup, distillates, gas chromatography.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Neilson, A; Renfrewshire, I; Black, W

1889-06-14

The invention relates to a method of, and apparatus for, distilling shale, coal, or other oil or tar-yielding minerals, to obtain gases, liquids, or other products. The distillation is effected in vertical retorts by the combustion of the partially spent material in the lower part of the retorts, to which steam and air are admitted. The retorts are built of firebrick, and provided with iron casings. They are fed through hoppers and discharged through the openings. The discharging is facilitated by a cone, or its equivalent, in the base of each retort. Steam and air are admitted through the pipes. The interior may be viewed through holes. The products are taken off from the space around the hopper.

Efficiency of fermionic quantum distillation

Energy Technology Data Exchange (ETDEWEB)

Herbrych, Jacek W. [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Feiguin, Adrian E. [Northeastern Univ., Boston, MA (United States); Dagotto, Elbio R. [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Heidrich-Meisner, F. [Ludwig-Maximilians-Univ. Munchen, Munchen (Germany)

2017-09-13

Here, we present a time-dependent density-matrix renormalization group investigation of the quantum distillation process within the Fermi-Hubbard model on a quasi-one-dimensional ladder geometry. The term distillation refers to the dynamical, spatial separation of singlons and doublons in the sudden expansion of interacting particles in an optical lattice, i.e., the release of a cloud of atoms from a trapping potential. Remarkably, quantum distillation can lead to a contraction of the doublon cloud, resulting in an increased density of the doublons in the core region compared to the initial state. As a main result, we show that this phenomenon is not limited to chains that were previously studied. Interestingly, there are additional dynamical processes on the two-leg ladder such as density oscillations and self-trapping of defects that lead to a less efficient distillation process. An investigation of the time evolution starting from product states provides an explanation for this behavior. Initial product states are also considered since in optical lattice experiments, such states are often used as the initial setup. We propose configurations that lead to a fast and efficient quantum distillation.

Distilling coal, etc

Energy Technology Data Exchange (ETDEWEB)

Nelson, J

1917-12-21

Coals of various kinds such as shales, bitumens, and oil sand, peat, etc. are distilled at 350 to 450/sup 0/C and in the presence of vapors and gases obtained by cracking hydrocarbon oils, or the gases obtained by separating the condensable hydrocarbons therefrom, and, if desired, with the addition of superheated steam. The hydrocarbons are properly cracked by passing through molten lead as described in Specification 116,304. According to the Provisional Specification, superheated steam alone may be used to effect the distillation.

Observer-Based Perturbation Extremum Seeking Control with Input Constraints for Direct-Contact Membrane Distillation Process

KAUST Repository

Eleiwi, Fadi

2017-05-08

An Observer-based Perturbation Extremum Seeking Control (PESC) is proposed for a Direct-Contact Membrane Distillation (DCMD) process. The process is described with a dynamic model that is based on a 2D Advection-Diffusion Equation (ADE) model which has pump flow rates as process inputs. The objective of the controller is to optimize the trade-off between the permeate mass flux and the energy consumption by the pumps inside the process. Cases of single and multiple control inputs are considered through the use of only the feed pump flow rate or both the feed and the permeate pump flow rates. A nonlinear Lyapunov-based observer is designed to provide an estimation for the temperature distribution all over the designated domain of the DCMD process. Moreover, control inputs are constrained with an anti-windup technique to be within feasible and physical ranges. Performance of the proposed structure is analyzed, and simulations based on real DCMD process parameters for each control input are provided.

Observer-based perturbation extremum seeking control with input constraints for direct-contact membrane distillation process

Science.gov (United States)

Eleiwi, Fadi; Laleg-Kirati, Taous Meriem

2018-06-01

An observer-based perturbation extremum seeking control is proposed for a direct-contact membrane distillation (DCMD) process. The process is described with a dynamic model that is based on a 2D advection-diffusion equation model which has pump flow rates as process inputs. The objective of the controller is to optimise the trade-off between the permeate mass flux and the energy consumption by the pumps inside the process. Cases of single and multiple control inputs are considered through the use of only the feed pump flow rate or both the feed and the permeate pump flow rates. A nonlinear Lyapunov-based observer is designed to provide an estimation for the temperature distribution all over the designated domain of the DCMD process. Moreover, control inputs are constrained with an anti-windup technique to be within feasible and physical ranges. Performance of the proposed structure is analysed, and simulations based on real DCMD process parameters for each control input are provided.

Distilling solid carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1926-12-04

In a process of distilling solid carbonaceous materials with by-product recovery, the time factor and the temperature gradient during the distillation period are so controlled that a temperature difference exceeding 150/sup 0/C is avoided between the temperatures at the center and periphery of any suitable size of material or thickness of fuel bed. The material is heated by direct contact with an inert gas, such as water gas, producer gas, or combustion gases, which is passed in counterflow to the material and whose volume is such as to lower the vapor tension or partial pressure of the volatilizable oils and to withdraw the oils without cracking of the oil vapors. The material may be subjected to a preliminary heat treatment by gases containing 2 to 3 percent of free oxygen to reduce its coking properties, and free oxygen may be added either to the heating gases during the heat treatment, or to the retort and heating gases and vapors to polymerize resinous bodies prior to condensation or during condensation and while the oils are still wholly or partially in the vapor state.

Membrane distillation for milk concentration

NARCIS (Netherlands)

Moejes, S.N.; Romero Guzman, Maria; Hanemaaijer, J.H.; Barrera, K.H.; Feenstra, L.; Boxtel, van A.J.B.

2015-01-01

Membrane distillation is an emerging technology to concentrate liquid products while producing high quality water as permeate. Application for desalination has been studied extensively the past years, but membrane distillation has also potential to produce concentrated food products like

Refining shale-oil distillates

Energy Technology Data Exchange (ETDEWEB)

Altpeter, J

1952-03-17

A process is described for refining distillates from shale oil, brown coal, tar, and other tar products by extraction with selective solvents, such as lower alcohols, halogen-hydrins, dichlorodiethyl ether, liquid sulfur dioxide, and so forth, as well as treating with alkali solution, characterized in that the distillate is first treated with completely or almost completely recovered phenol or cresotate solution, the oil is separated from the phenolate with solvent, for example concentrated or adjusted to a determined water content of lower alcohol, furfural, halogen-hydrin, dichlorodiethyl ether, liquid sulfur dioxide, or the like, extracted, and the raffinate separated from the extract layer, if necessary after distillation or washing out of solvent, and freeing with alkali solution from residual phenol or creosol.

HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY FOR DETERMINATION OF AROMATIC ALDEHYDES IN WINE DISTILLATES

Directory of Open Access Journals (Sweden)

Elena Nezalzova

2011-06-01

Full Text Available Quality control of alcoholic beverages, coming into the market, is a defining element in preventing the production and supplying of defective products. One of the main criteria for quality control of wine distillates is to estimate their age, and more precisely the period of maturation as the dominant factor in determining the quality of cognacs and, consequently, their market price. On the opinion of majority scientists, one of the main factors, which determines the age of wine distillates, is the content of aromatic aldehydes, mostly vanillin, and their ratio.

A Comparative study between MPC and PI controller to control vacuum distillation unit for producing LVGO, MVGO, and HVGO

Science.gov (United States)

Wahid, A.; Prasetyo, A. P.

2018-03-01

This study describes the selection of controllers in the vacuum distillation unit (VDU) between a model predictive control (MPC) and a proportional-integral (PI) controller by comparing the integral square error (ISE) values. Design of VDU in this simulation is based on modified Metso Automation Inc. scheme. Controlled variables in this study are feed flow rate, feed temperature, top stage pressure, condenser level, bottom stage temperature, LVGO (light vacuum gas oil), MVGO (medium vacuum gas oil), and HVGO (heavy vacuum gas oil) flow rate. As a result, control performance improvements occurred as using MPC compared to PI controllers, when testing a set-point change, of feed flow rate control, feed temperature, top-stage pressure, bottom-stage temperature and flow rate of LVGO, MVGO, and HVGO, respectively, 36%, 6%, 92%, 53%, 90%, 96% and 88%. Only on condenser level control PI performs much better than the MPC. So PI controller is used for level condenser control. While for the test of disturbance rejection, by changing feed flow rate by 10%, there is improvement of control performance using MPC compared to PI controller on feed temperature control, top-stage pressure, bottom-stage temperature and flow rate LVGO, MVGO and HVGO 0.3%, 0.7%, 14%, 2.7%, 10.6% and 4.3%, respectively.

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Trumble, M J

1925-06-29

Carbonaceous materials such as coal, oil shale, peat, or wood are destructively distilled while being subjected to the action of superheated steam and hydrogen, the latter being provided by dissociating a part of the superheated steam. The materials are charged into a retort heated by a burner and superheated steam and hydrogen are passed in by a pipe and nozzles. The distillates enter a dust extractor through openings and escape through openings shielded by cones into an outlet pipe leading to condensers. The dust which settles in the bottom of the apparatus is periodically removed.

Method of distilling organic materials

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, E G.T.

1921-11-11

In the distillation of organic materials, by means of coursing heated gases through the distillation chamber, that can be heated by other means also, a method is given by which the hot gases coming from the distillation chamber are cooled in one or more heat-absorbent devices (for example, in spray coolers, condensers and/or water). The greater part of the products or constituents condensable at ordinary temperature are separated from the vapors and gases, and thereafter the gases should be passed through the distillation chamber after the necessary additional heating in special heaters, as one or more heat producers, suitably of the same construction as the heat absorbers, for heating and saturation with steam by means of warm condensate and/or water obtained fully or partly from the heat absorbers, possibly after separation of tar or oil from them. The patent has 11 other claims.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Urquhart, D

1882-08-19

Manufacture of ammonia and purification of shale oils are described. In the distillation of shales, increase of ammonia is obtained and the oils are less contaminated by sulfur, by mixing a small proportion, about two to three percent, of lime or slaked line with the shale. The same process is used with other carbonaceous substances containing nitrogen, such as peat, coal, or the like; but a smaller proportion of lime is used than in the former case, and the lime is slaked with caustic soda solution. When slack or waste coal or other carbonaceous substances are distilled by heated air or gases arising from imperfect combustion, as in furnaces on the gas producer principle, slaked lime is added to the slack or other material.

Distilling oils

Energy Technology Data Exchange (ETDEWEB)

Leffer, L G

1912-01-29

In a process for converting heavy hydrocarbons, such as petroleum or shale oil, into light hydrocarbons by distilling under the pressure of an inert gas, the operation is conducted at a temperature not exceeding 410/sup 0/C and under an accurately regulated pressure, the gas being circulated through the still and the condenser by means of a pump. The oil in the still may be agitated by stirring vanes or by blowing the gas through it. Hydrogen, nitrogen, carbon dioxide, methane, or gases generated in the distillation may be used as pressure media; the gas is heated before its admission to the still. A pressure of from 11 to 12 atmospheres is used in treating gas oil. Specification 10,277/89 is referred to.

Low grade bioethanol for fuel mixing on gasoline engine using distillation process

Science.gov (United States)

Abikusna, Setia; Sugiarto, Bambang; Suntoro, Dedi; Azami

2017-03-01

Utilization of renewable energy in Indonesia is still low, compared to 34% oil, 20% coal and 20% gas, utilization of energy sources for water 3%, geothermal 1%, 2% biofuels, and biomass 20%. Whereas renewable energy sources dwindling due to the increasing consumption of gasoline as a fuel. It makes us have to look for alternative renewable energy, one of which is bio ethanol. Several studies on the use of ethanol was done to the researchers. Our studies using low grade bio ethanol which begins with the disitillation independently utilize flue gas heat at compact distillator, produces high grade bio ethanol and ready to be mixed with gasoline. Stages of our study is the compact distillator design of the motor dynamic continued with good performance and emission testing and ethanol distilled. Some improvement is made is through the flue gas heat control mechanism in compact distillator using gate valve, at low, medium, and high speed engine. Compact distillator used is kind of a batch distillation column. Column design process using the shortcut method, then carried the tray design to determine the overall geometry. The distillation is done by comparing the separator with a tray of different distances. As well as by varying the volume of the feed and ethanol levels that will feed distilled. In this study, we analyzed the mixing of ethanol through variation between main jet and pilot jet in the carburetor separately interchangeably with gasoline. And finally mixing mechanism bio ethanol with gasoline improved with fuel mixer for performance.

Solar power water distillation unit

International Nuclear Information System (INIS)

Hameed, Kamran; Khan, Muhammad Muzammil; Ateeq, Ijlal Shahrukh; Omair, Syed Muhammad; Ahmer, Muhammad; Wajid, Abdul

2013-01-01

Clean drinking water is the basic necessity for every human being, but about 1.1 billion people in the world lacked proper drinking water. There are many different types of water purification processes such as filtration, reverse osmosis, ultraviolet radiation, carbon absorption, but the most reliable processes are distillation and boiling. Water purification, such as distillation, is especially important in regions where water resources or tap water is not suitable for ingesting without boiling or chemical treatment. In design project It treats the water by combining different methods such as Filtration, Distillation and a technique called concentrated solar power (CSP). Distillation is literally the method seen in nature, whereby: the sun heats the water on the earth's surface, the water is turned into a vapor (evaporation) and rises, leaving contaminants behind, to form clouds. As the upper atmosphere drops in temperature the vapors cool and convert back to water to form water. In this project distillation is achieved by using a parabolic mirror which boils water at high temperature. Filtration is done by sand filter and carbon filter. First sand filter catches the sand particles and the carbon filter which has granules of active carbon is used to remove odor dissolved gases from water. This is the Pre-treatment of water. The filtered water is then collected in a water container at a focus of parabolic mirror where distillation process is done. Another important feature of designed project is the solar tracking of a parabolic mirror which increases the efficiency of a parabolic mirror [1],[2].

A totally heat-integrated distillation column (THIDiC) - the effect of feed pre-heating by distillate

Energy Technology Data Exchange (ETDEWEB)

Huang Kejin [School of Information Science and Technology, Beijing University of Chemical Technology, Beijing 100029 (China)], E-mail: huangkj@mail.buct.edu.cn; Shan Lan; Zhu Qunxiong [School of Information Science and Technology, Beijing University of Chemical Technology, Beijing 100029 (China); Qian Jixin [School of Information Science and Technology, Zhejiang University, Zhejiang 300027 (China)

2008-06-15

An ideal heat-integrated distillation column (ideal HIDiC) is characterized by external zero-reflux and zero-reboil ratio operation. Since the distillate is a high-pressure vapor phase flow, it can be used to pre-heat the feed to be separated, thereby giving rise to a totally heat-integrated distillation column (THIDiC). Although the THIDiC is more thermodynamically efficient than the ideal HIDiC, it is found that the heat integration between the distillate and feed turns it into an open-loop integrating process and poses additional difficulties to process operation. Therefore, a careful decision must be made on the selection between the ideal HIDiC and the THIDiC during process development. In this paper, separation of a binary equimolar mixture of benzene and toluene is selected as an illustrative example. Both process design and operability analysis are conducted, with special emphasis focused on the characteristics of feed pre-heating with distillate. The results obtained show deep insight into the design and operation of the THIDiC.

A totally heat-integrated distillation column (THIDiC) - the effect of feed pre-heating by distillate

International Nuclear Information System (INIS)

Huang Kejin; Shan Lan; Zhu Qunxiong; Qian Jixin

2008-01-01

An ideal heat-integrated distillation column (ideal HIDiC) is characterized by external zero-reflux and zero-reboil ratio operation. Since the distillate is a high-pressure vapor phase flow, it can be used to pre-heat the feed to be separated, thereby giving rise to a totally heat-integrated distillation column (THIDiC). Although the THIDiC is more thermodynamically efficient than the ideal HIDiC, it is found that the heat integration between the distillate and feed turns it into an open-loop integrating process and poses additional difficulties to process operation. Therefore, a careful decision must be made on the selection between the ideal HIDiC and the THIDiC during process development. In this paper, separation of a binary equimolar mixture of benzene and toluene is selected as an illustrative example. Both process design and operability analysis are conducted, with special emphasis focused on the characteristics of feed pre-heating with distillate. The results obtained show deep insight into the design and operation of the THIDiC

Fate of DDT in grape juice when fermented and distilled into arak

International Nuclear Information System (INIS)

Kawar, N.S.

1975-01-01

Since DDT is still used on grapevines to control insect pests, the fate of this insecticide in grape juice fermented and distilled into arak was investigated. Fermentation of the juice resulted in extensive conversion of DDT to DDD. Distillation of the fermented juice resulted in further conversion of DDT to DDD. Moreover, the major portion of both DDT and DDD remained in the undistilled fraction. The second distillation resulted in further distribution of DDT and DDD among the four fractions, thus leaving very low levels of both compounds in the finished product. DDT residue in arak constituted only 2% of the amount added to the fresh juice. (author)

27 CFR 24.183 - Use of distillates containing aldehydes.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Use of distillates... distillates containing aldehydes. Distillates containing aldehydes may be received on wine premises for use in the fermentation of wine and then returned to the distilled spirits plant from which distillates were...

Three-phase fluidized distillation

International Nuclear Information System (INIS)

Ravagnani, T.M.K.; Pereira, J.A.F.R.

2001-01-01

Separation efficiency in distillation operations can be improved by modifying the characteristics of the dispersions formed on the trays. The present work reports on the hydrodynamic and mass transfer characteristics of liquid-solid-vapour dispersions formed on sieve trays without downcomers of a distillation column operating under total reflux conditions. Murphree efficiency and the operating limits of distillation using the ethanol-n-butanol system are analyzed for a large range of vapour velocities and liquid mixture compositions, utilising wettable PVC particles and non-wettable silicone, PE, and Teflon((R)) particles. It was verified that wettable particles show a drastic reduction in the upper operating limit of vapour velocity, but this does not occur for non-wettable particles. Tray efficiency can be increased when non-wettable particles are used, mainly for high vapour velocity operations. (author)

7 CFR 160.8 - Steam distilled wood turpentine.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Steam distilled wood turpentine. 160.8 Section 160.8... STANDARDS FOR NAVAL STORES General § 160.8 Steam distilled wood turpentine. The designation “steam distilled wood turpentine” shall refer to the kind of spirits of turpentine obtained by steam distillation from...

Ekstraksi Minyak Atsiri Dari Akar Wangi Menggunakan Metode Steam - Hydro distillation dan Hydro distilation dengan Pemanas Microwave

Directory of Open Access Journals (Sweden)

Maulana M Al Hanief

2013-09-01

Full Text Available Penelitian ini bertujuan untuk memperoleh minyak atsiri dari akar wangi dengan modifikasi metode steam-hydro distillation dan hydro distillation yaitu menggunakan pemanasan microwave kemudian membandingkan hasilnya dengan penelitian sebelumnya. Modifikasi ini diharapkan lebih efisien dalam masalah lama penyulingan dan kualitas serta kuantitas rendemen minyak yang lebih baik dan banyak. Penelitian ini menggunakan dua metode yaitu steam-hydro distillation dan hydro distillation dengan pemanfaatan gelombang mikro. Bahan baku yang digunakan dalam penelitian adalah akar wangi jenis pulus wangi yang tumbuh di Kabupaten Garut, Jawa Barat. Variabel yang digunakan adalah bahan baku yang dicacah dan bahan baku utuh dengan variasi massa bahan 50 gr, 60, gr, 70 gr, 80 gr, dan 90 gr dengan pelarut air sebanyak 450 ml dalam labau distiller berukuran 1000 ml. Lama penyulingan adalah lima jam dengan pengamatan tiap 30 menit serta daya yang digunakan adalah 400 Watt. Analisa terhadap hasil minyak atsiri yang diperoleh antara lain analisa GC-MS, spesific gravity, indeks bias, dan bilangan asam. Hasil dari penelitian ini dibandingkan dengan hasil penelitian terdahulu yang tidak memanfaatkan gelombang mikro. Dari hasil penelitian diperoleh % rendemen kumulatif, sifat fisik, sifat kimia, dan kandungan komponen minyak dari metode steam-hydro distillation lebih baik dibandingkan metode hydro distillation ditandai dengan kuantitas dan kualitas yang sesuai dengan SNI.  Sementara itu jika dibandingkan dengan metode terdahulu dapat disimpulkan bahwa penggunaan gelombang mikro lebih efisien dalam waktu dan kuantitas serta kualitas minyak yang lebih baik dibandingkan tanpa penggunaan gelombang mikro

Low temperature distillation of coal, shale, etc

Energy Technology Data Exchange (ETDEWEB)

1938-08-12

A process is disclosed for the low temperature distillation of solid carbonaceous fuels, such as coal, lignite, shale or the like, which comprises feeding or supplying the comminuted fuel in the form of a layer of shallow depth to drying and distilling zones in succession moving the fuel forward through the zones, submitting it to progressively increasing nonuniform heating therein by combustion gases supplied to the distillation zone and traveling thence to the drying zone, the gases heating the distillation zone indirectly and the drying zone both indirectly and then directly such that the fuel retains its solid discrete form during substantially the whole of its travel through the drying and distillation zones, subjecting the fuel for a portion of its travel to a zigzag ploughing and propelling movement on a heated sole, and increasing the heating so as to cause fusion of the fuel immediately prior to its discharge from the distillation zone.

Improving distillation method and device of tritiated water analysis for ultra high decontamination efficiency

International Nuclear Information System (INIS)

Fang, Hsin-Fa; Wang, Chu-Fang; Lin, Chien-Kung

2015-01-01

It is important that monitoring environmental tritiated water for understanding the contamination dispersion of the nuclear facilities. Tritium is a pure beta radionuclide which is usually measured by Liquid Scintillation Counting (LSC). The average energy of tritum beta is only 5.658 keV that makes the LSC counting of tritium easily be interfered by the beta emitted by other radionuclides. Environmental tritiated water samples usually need to be decontaminated by distillation for reducing the interference. After Fukushima Nucleaer Accident, the highest gross beta concentration of groundwater samples obtained around Fukushima Daiichi Nuclear Power Station is over 1,000,000 Bq/l. There is a need for a distillation with ultra-high decontamination efficiency for environmental tritiated water analysis. This study is intended to improve the heating temperature control for better sub-boiling distillation control and modify the height of the container of the air cooling distillation device for better fractional distillation effect. The DF of Cs-137 of the distillation may reach 450,000 which is far better than the prior study. The average loss rate of the improved method and device is about 2.6% which is better than the bias value listed in the ASTM D4107-08. It is proven that the modified air cooling distillation device can provide an easy-handling, water-saving, low cost and effective way of purifying water samples for higher beta radionuclides contaminated water samples which need ultra-high decontamination treatment. - Highlights: • The improvements of method and device make the decontaminatin factor (DF) of Cs-137 of distillation reach over 450,000. • The decontamination factor ( DF) value may be increased about 20 times by increasing the height of the container from 7 cm to 20 cm. • The device provides an easy-handling, water-saving, low cost, stable and effective way for the distillation of triated water analysis.

Quality Evaluation of Agricultural Distillates Using an Electronic Nose

Directory of Open Access Journals (Sweden)

Tomasz Dymerski

2013-11-01

Full Text Available The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing in quality was obtained by barbotage. Interpretation of the results involved three data analysis techniques: principal component analysis, single-linkage cluster analysis and cluster analysis with spheres method. The investigations prove the usefulness of the presented technique in the quality control of agricultural distillates. Optimum measurements conditions were also defined, including volumetric flow rate of carrier gas (15 L/h, thermostat temperature during the barbotage process (15 °C and time of sensor signal acquisition from the onset of the barbotage process (60 s.

Quality evaluation of agricultural distillates using an electronic nose.

Science.gov (United States)

Dymerski, Tomasz; Gębicki, Jacek; Wardencki, Waldemar; Namieśnik, Jacek

2013-11-25

The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing in quality was obtained by barbotage. Interpretation of the results involved three data analysis techniques: principal component analysis, single-linkage cluster analysis and cluster analysis with spheres method. The investigations prove the usefulness of the presented technique in the quality control of agricultural distillates. Optimum measurements conditions were also defined, including volumetric flow rate of carrier gas (15 L/h), thermostat temperature during the barbotage process (15 °C) and time of sensor signal acquisition from the onset of the barbotage process (60 s).

40 CFR 721.9635 - Terpene residue distillates.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Terpene residue distillates. 721.9635... Substances § 721.9635 Terpene residue distillates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as terpene residue distillates (PMN P-96-897...

Study on Gas-liquid Falling Film Flow in Internal Heat Integrated Distillation Column

Science.gov (United States)

Liu, Chong

2017-10-01

Gas-liquid internally heat integrated distillation column falling film flow with nonlinear characteristics, study on gas liquid falling film flow regulation control law, can reduce emissions of the distillation column, and it can improve the quality of products. According to the distribution of gas-liquid mass balance internally heat integrated distillation column independent region, distribution model of heat transfer coefficient of building internal heat integrated distillation tower is obtained liquid distillation falling film flow in the saturated vapour pressure of liquid water balance, using heat transfer equation and energy equation to balance the relationship between the circulating iterative gas-liquid falling film flow area, flow parameter information, at a given temperature, pressure conditions, gas-liquid flow falling film theory makes the optimal parameters to achieve the best fitting value with the measured values. The results show that the geometric gas-liquid internally heat integrated distillation column falling film flow heat exchange area and import column thermostat, the average temperature has significant. The positive correlation between the heat exchanger tube entrance due to temperature difference between inside and outside, the heat flux is larger, with the increase of internal heat integrated distillation column temperature, the slope decreases its temperature rise, which accurately describes the internal gas-liquid heat integrated distillation tower falling film flow regularity, take appropriate measures to promote the enhancement of heat transfer. It can enhance the overall efficiency of the heat exchanger.

DESIGN AND CONSTRUCTION OF A REFLUX COLUMN DISTILLATION UNIT FOR BIO-ETHANOL PRODUCTION FROM SUGARCANE SUBSTRATE

Directory of Open Access Journals (Sweden)

J. O. Olaoye

2011-06-01

Full Text Available A bio-ethanol distilling tank was designed and constructed to distil ethanol from sugarcane substrate. The machine has a capacity to process 200 litres of substrate at full load of the boiler. The distiller has mlntemalReflux Still Condenser (IRSC that controls the internal re-distillation process and the separation of the final output. The column diameter was 40 mm. An anaerobic fermentation of substrate was adopted before distillation could be carried out. The fermented substrate was adjusted to an optimum pH level value of 4-5 by addition of 0.1 M HjSQ, and the optimum temperature was within the temperature range of 29-38°C. A charcoal pot was used as heat source. The results of the machine evaluation showed that optimum yield occurred at 0.0325 ratio of substrate to ethanol yield. An average distilled product of 2.1 litres was obtained at highest ratio of substrate to ethanol yield of 0.033 when the distillation time was 45 minutes. The total distilled products after 1XA hours of distillation was estimated at 4.25 litres. It was observed that the fermentation and distillation processes were done in situ, and could definitely affect clear separation of the fermentable portion of the fermented sugar solution.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Cosden, S; Cosden, J S

1937-09-08

A means and process are described for the destructive distillation of solid carbonaceous materials in which the process comprises charging the material, in a finely divided condition into a stream of hot combustion gases, and allows the hot gases to act pyrolytically on the organic compounds contained in the material, separating the volatile liberated constituents from residuary constituents. Hot reaction gases are generated by fuel ignition means in a generator and are immediately intermingled with comminuted carbonaceous material from a hopper, in a narrow conduit. The mixture of material and reaction fluid is then passed through an elongated confined path, which is exteriorly heated by the combustion chamber of the furnace, where the destructive distillation is effected. Volatile and solid constituents are separated in the chamber, and the volatile constituents are fractionated and condensed.

Destructive distillation under pressure

Energy Technology Data Exchange (ETDEWEB)

1932-09-08

A process of destructive distillation of distillable carbonaceous material under pressure is described, consisting of regulating the temperature by introducing the carbonaceous materials to a point where the reaction of hydrogenation has begun but has not stopped, by placing it in indirect heat-exchange with a cooling agent at a critical temperature below the reaction temperature, the agent being under pressure and introduced in the liquid state. Water is used as the cooling agent.

Secret key distillation from shielded two-qubit states

International Nuclear Information System (INIS)

Bae, Joonwoo

2010-01-01

The quantum states corresponding to a secret key are characterized using the so-called private states, where the key part consisting of a secret key is shielded by the additional systems. Based on the construction, it was shown that a secret key can be distilled from bound entangled states. In this work, I consider the shielded two-qubit states in a key-distillation scenario and derive the conditions under which a secret key can be distilled using the recurrence protocol or the two-way classical distillation, advantage distillation together with one-way postprocessing. From the security conditions, it is shown that a secret key can be distilled from bound entangled states in a much wider range. In addition, I consider the case that in which white noise is added to quantum states and show that the classical distillation protocol still works despite a certain amount of noise although the recurrence protocol does not.

Advanced Control of Turbofan Engines

CERN Document Server

Richter, Hanz

2012-01-01

Advanced Control of Turbofan Engines describes the operational performance requirements of turbofan (commercial)engines from a controls systems perspective, covering industry-standard methods and research-edge advances. This book allows the reader to design controllers and produce realistic simulations using public-domain software like CMAPSS: Commercial Modular Aero-Propulsion System Simulation, whose versions are released to the public by NASA. The scope of the book is centered on the design of thrust controllers for both steady flight and transient maneuvers. Classical control theory is not dwelled on, but instead an introduction to general undergraduate control techniques is provided. This book also: Develops a thorough understanding of the challenges associated with engine operability from a control systems perspective, describing performance demands and operational constraints into the framework and language of modern control theory Presents solid theoretical support for classical and advanced engine co...

Reduced-Order Dynamic Modeling, Fouling Detection, and Optimal Control of Solar-Powered Direct Contact Membrane Distillation

KAUST Repository

Karam, Ayman M.

2016-12-01

Membrane Distillation (MD) is an emerging sustainable desalination technique. While MD has many advantages and can be powered by solar thermal energy, its main drawback is the low water production rate. However, the MD process has not been fully optimized in terms of its manipulated and controlled variables. This is largely due to the lack of adequate dynamic models to study and simulate the process. In addition, MD is prone to membrane fouling, which is a fault that degrades the performance of the MD process. This work has three contributions to address these challenges. First, we derive a mathematical model of Direct Contact Membrane Distillation (DCMD), which is the building block for the next parts. Then, the proposed model is extended to account for membrane fouling and an observer-based fouling detection method is developed. Finally, various control strategies are implemented to optimize the performance of the DCMD solar-powered process. In part one, a reduced-order dynamic model of DCMD is developed based on lumped capacitance method and electrical analogy to thermal systems. The result is an electrical equivalent thermal network to the DCMD process, which is modeled by a system of nonlinear differential algebraic equations (DAEs). This model predicts the water-vapor flux and the temperature distribution along the module length. Experimental data is collected to validate the steady-state and dynamic responses of the proposed model, with great agreement demonstrated in both. The second part proposes an extension of the model to account for membrane fouling. An adaptive observer for DAE systems is developed and convergence proof is presented. A method for membrane fouling detection is then proposed based on adaptive observers. Simulation results demonstrate the performance of the membrane fouling detection method. Finally, an optimization problem is formulated to maximize the process efficiency of a solar-powered DCMD. The adapted method is known as Extremum

¹³⁶ Xe enrichment through cryogenic distillation

Energy Technology Data Exchange (ETDEWEB)

Back, Henning O.; Bottenus, Daniel R.; Clayton, Christopher K.; Stephenson, David E.; TeGrotenhuis, Ward E.

2017-09-01

The next generation of 136Xe neutrinoless double beta decay experiments will require on the order of 5 tons of enriched 136Xe. By estimating the relative volatilities of the xenon isotopes and using standard chemical engineering techniques we explore the feasibility of using cryogenic distillation to produce 5 tons of 80% enriched 136Xe in 5-6 years. With current state-of-the-art distillation column packing materials we can estimate the total height of a traditional cryogenic distillation column. We also, report on how Micro Channel Distillation may reduce the overall size of a distillation system for 136Xe production.

Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

International Nuclear Information System (INIS)

Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun

1995-12-01

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N 2 and H 2 -D 2 distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N 2 distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H 2 , HD, D 2 , HT, DT, T 2 ) distillation column showed good performance after comparison with the result of a JAERI code, and a H 2 -D 2 distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H 2 -D 2 distillation process was suggested. A feasibility on modification of H 2 -D 2 distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author)

Distillation of shale in situ

Energy Technology Data Exchange (ETDEWEB)

de Ganahl, C F

1922-07-04

To distill buried shale or other carbon containing compounds in situ, a portion of the shale bed is rendered permeable to gases, and the temperature is raised to the point of distillation. An area in a shale bed is shattered by explosives, so that it is in a relatively finely divided form, and the tunnel is then blocked by a wall, and fuel and air are admitted through pipes until the temperature of the shale is raised to such a point that a portion of the released hydrocarbons will burn. When distillation of the shattered area takes place and the lighter products pass upwardly through uptakes to condensers and scrubbers, liquid oil passes to a tank and gas to a gasometer while heavy unvaporized products in the distillation zone collect in a drain, flow into a sump, and are drawn off through a pipe to a storage tank. In two modifications, methods of working are set out in cases where the shale lies beneath a substantially level surface.

Operation and Design of Diabatic Distillation Processes

DEFF Research Database (Denmark)

Bisgaard, Thomas

Diabatic operation of a distillation column implies that heat is exchanged in one or more stages in the column. The most common way of realising diabatic operation is by internal heat integration resulting in a heat-integrated distillation column (HIDiC). When operating the rectifying section...... at a higher pressure, a driving forcefor transferring heat from the rectifying section to the stripping section is achieved. As a result, the condenser and reboiler duties can be significantly reduced. For two-product distillation, the HIDiC is a favourable alternative to the conventional distillation column....... Energy savings up to 83% are reported for the HIDiC compared to the CDiC, while the reported economical savings are as high as 40%. However, a simpler heat-integrated distillation column configuration exists, which employs compression in order to obtain a direct heat integration between the top vapour...

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1922-07-21

In the distillation of shale and similar materials the shale is ground and briquetted and the briquettes are placed in a retort so that air passages are left between them, after which they are uniformly and slowly heated to at least 700/sup 0/C, the air passages facilitating the escape of the oil vapors, and the slow heating preventing fusion of the flux forming constituents. After the bitumen has been driven off, air is passed into the retort and heating continued to about 1050/sup 0/C, the result being a porous product suitable for insulating purposes or as a substitute for kieselguhr. The ground shale may be mixed prior to distillation with peat, sawdust, or the like, and with substances which yield acids, such as chlorides, more particularly magnesium chloride, the acids acting on the bitumen.

Distilling coal

Energy Technology Data Exchange (ETDEWEB)

Blythe, F C

1914-09-14

In the destructive distillation of bituminous coal, heavy hydrocarbon oil, such as petroleum, kerosine, shale oil, and heavy tar oil, obtained in some cases during the process, is added to the coal, which is then distilled under pressure and at a comparatively low temperature regulated so as to produce a large proportion of hydrocarbon oils and a small proportion of permanent gas. In one method, about 5 to 10 parts of hydrocarbon oil are mixed with 100 parts of crushed or ground coal, and the mixture is heated in a closed vessel, provided in some cases with an agitator, under a pressure of about 60 lb/in/sup 2/, and the temperature may be gradually raised to 350/sup 0/C and then to about 500/sup 0/C. The heating may be by means of superheated steam with or without external heat.

Characteristics of Wet and Dried Distillers Grains on Ruminal Fermentation and Effects of Dietary Wet Distillers Grains on Performance of Hanwoo Steers

Directory of Open Access Journals (Sweden)

Ill Young Kim

2015-05-01

Full Text Available Two experiments were conducted to evaluate the nutrient composition, in vitro dry matter disappearance (IVDMD and organic matter disappearance (IVOMD of three kinds of distillers grains (DG; i wet distillers grains (WDG, KRW 25/kg, ii dried distillers grains (DDG, KRW 280/kg, iii dried distillers grains with solubles (DDGS, KRW 270/kg produced from tapioca 70% and rice 30%, and to evaluate dietary effects of WDG on the performance of Hanwoo steers. In Exp. 1, twelve-WDG, four-DDG and one-DDGS were collected from seven ethanol plants. Average crude protein, crude fiber, neutral detergent fiber, and acid detergent fiber of WDG, DDG, and DDGS were: 32.6%, 17.8%, 57.5%, and 30.2% for WDG, 36.7%, 13.9%, 51.4%, and 30.5% for DDG, and 31.0%, 11.9%, 40.3%, and 21.2% for DDGS (DM basis, respectively. The DDGS had a higher quantity of water-soluble fraction than WDG and DDG and showed the highest IVDMD (p<0.05 in comparison to others during the whole experimental time. The IVDMD at 0 to 12 h incubation were higher (p<0.05 in DDG than WDG, but did not show significant differences from 24 to 72 h. The same tendency was observed in IVOMD, showing that DG made from tapioca and rice (7:3 can be used as a feed ingredient for ruminants. Considering the price, WDG is a more useful feed ingredient than DDG and DDGS. In Exp. 2, 36 Hanwoo steers of 21 months (495.1±91 kg were randomly assigned to one of three dietary treatments for 85 days; i Control (total mixed ration, TMR, ii WDG 10% (TMR containing 10% of WDG, as fed basis, and iii WDG 20% (TMR containing 20% of WDG, as fed basis. With respect to body weight and average daily gain, there were no differences between control and WDG treatments during the whole experimental period. Dry matter intake of control (9.34 kg, WDG 10% (9.21 kg and 20% (8.86 kg and feed conversion ratio of control (13.0, WDG 10% (13.2 and 20% (12.1 did not show differences between control and WDG treatments. Thus, the use of WDG up to 20

Early changes produced in mouse skin by the application of three middle distillates.

Science.gov (United States)

Grasso, P; Sharratt, M; Ingram, A J

1988-01-01

It has been reported by the American Petroleum Institute (API) that dermal applications of certain middle distillates of mineral oils can result in high incidences of skin tumours in mice. This was unexpected as the polycyclic aromatic hydrocarbon (PAH) levels in these were below detection limits. To examine the possible role of tissue injury in the induction of tumours, the skin reactions produced by thrice weekly applications of three middle distillates similar to those tested by the API were examined grossly and histopathologically at intervals up to 6 weeks. Various reference materials and oils were used as controls. Preliminary histological examination showed that severe skin damage was present from week 1 onwards in mice treated with the three middle distillates, two of them producing epidermal loss and ulceration. Marked epidermal hyperplasia was produced by all three middle distillates. These findings support the view that regenerative epidermal hyperplasia due to repeated severe skin damage may have exerted a powerful promotional effect in the production of the skin tumours by middle distillates in the API study.

Brain Emotional Learning Based Intelligent Decoupler for Nonlinear Multi-Input Multi-Output Distillation Columns

Directory of Open Access Journals (Sweden)

M. H. El-Saify

2017-01-01

Full Text Available The distillation process is vital in many fields of chemical industries, such as the two-coupled distillation columns that are usually highly nonlinear Multi-Input Multi-Output (MIMO coupled processes. The control of MIMO process is usually implemented via a decentralized approach using a set of Single-Input Single-Output (SISO loop controllers. Decoupling the MIMO process into group of single loops requires proper input-output pairing and development of decoupling compensator unit. This paper proposes a novel intelligent decoupling approach for MIMO processes based on new MIMO brain emotional learning architecture. A MIMO architecture of Brain Emotional Learning Based Intelligent Controller (BELBIC is developed and applied as a decoupler for 4 input/4 output highly nonlinear coupled distillation columns process. Moreover, the performance of the proposed Brain Emotional Learning Based Intelligent Decoupler (BELBID is enhanced using Particle Swarm Optimization (PSO technique. The performance is compared with the PSO optimized steady state decoupling compensation matrix. Mathematical models of the distillation columns and the decouplers are built and tested in simulation environment by applying the same inputs. The results prove remarkable success of the BELBID in minimizing the loops interactions without degrading the output that every input has been paired with.

Retort for distilling coal oil

Energy Technology Data Exchange (ETDEWEB)

Gibbon, J

1865-12-20

The construction of a retort for extracting or distilling coal oil or other products from cannel coal, shale, or schist, and more particularly of small coal or dust technically called slack, consists in applying self-acting feed and discharge apparatus to a revolving cylindrical wrought or cast iron retort, and constructing the inner surface of the cylindrical retort with a projecting ridge which encircles the interior of the retort in a spiral manner, the same as the interior of a female screw, and the ridge may be either cast upon or riveted on the internal surface, and is so arranged to cause the material to be operated upon to advance from one end of the retort to the other, as the retort revolves by following the course of the spiral screw or worm formed by the projecting ridge.

Effectiveness of neutral detergent fiber in whole cottonseed and dried distillers grains compared with alfalfa haylage.

Science.gov (United States)

Clark, P W; Armentano, L E

1993-09-01

Sixteen Holstein cows in midlactation were used in a 4 x 4 Latin square design to determine the effect of replacing alfalfa NDF with NDF from whole, linted cottonseed or dried distillers grains. Low and high fiber control diets (13 and 19% of dietary DM from alfalfa haylage NDF, respectively) were compared with diets designed to contain 13% of DM from alfalfa haylage NDF plus 6% of DM from either cottonseed NDF or distillers grains NDF. Dry matter intake, milk yield, and milk protein yield were lower from the high fiber control diet. Milk fat percentage was lower for the low fiber control diet. The cottonseed diet was equal to the high fiber control diet in stimulating rumination. Rumen acetate to propionate ratio was higher for the high fiber control and cottonseed diets. Replacing alfalfa with either of these high fiber by-product feeds increased feed intake and yields of milk fat and protein. The effectiveness of the NDF in distillers grains and cottonseed was not significantly different from that of alfalfa NDF for maintaining milk fat yield. Whole cottonseed and dried distillers grains appear to be good sources of effective fiber for maintaining milk fat test when they are substituted for alfalfa haylage fiber in lactating cow rations.

Process for distilling shales, peats, etc

Energy Technology Data Exchange (ETDEWEB)

Felizat, G

1922-01-09

The invention has for its object: a process for the distillation of shales, peats, and analogous products characterized by injecting across the substance a very rapid stream of superheated steam under pressure in order to effect a rapid removal of the products of distillation, to lower also the temperature at which it distills, to equalize the temperature throughout the mass, to hydrogenate the heavy hydrocarbons. An apparatus is put into operation characterized by the combination of a retort receiving the material to be distilled with a superheater for the steam, the combustion products which escape from the hearth of the superheater going to encircle the retort while the steam which comes off the superheater traverses this retort, the pressure of the steam being regulated by a convenient regulator; the products of the distillation result from the simultaneous action of the hot gases and steam on the contents of the retort being, on the other hand, separated at the outlet of this retort by means of cooling in a gas separator, a condenser, and part of the gas after being separated serving to heat the mentioned superheater.

Advanced Control Engineering

DEFF Research Database (Denmark)

Zhou, Jianjun

1999-01-01

This book is developed as a textbook for the course Advanced Control Engineering. The book is intended for students in mechanical engineering and its aim is to provide an understanding of modern control theory as well as methodologies and applications for state space modeling and design...

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Armour, J; Armour, H

1889-05-07

The invention relates to retorts and accessory apparatus for distilling shale or other oil-yielding minerals. A series of long vertical retorts, composed of fire-brick or similar refractory material, are arranged in two rows in a bench, being divided into groups of four by transverse vertical partitions. The retorts are surmounted by metal casings or hoppers into which the fresh mineral is charged, and from which the distillate passes off through lateral pipes. Any uncondensed gases from the retorts may be passed into the flues surrounding them by the pipe and burned. The products of combustion from a furnace pass through a series of horizontal flues, being compelled to pass completely round each retort before entering the flue above. The products from two or more sets pass from the upper flues into flues running along the top of the bench, and return through a central flue to the chimney.

Modeling Separation Dynamics in a Multi-Tray Bio-Ethanol Distillation Column

DEFF Research Database (Denmark)

Løhndorf, Petar Durdevic; Pedersen, Simon; Yang, Zhenyu

2015-01-01

the product quality and energy consumption in a typical bio-ethanol distillation column is proposed in this paper. The proposed model is derived based on mass and energy balance principles, with an empirical model of the evaporation dynamics of liquids on column trays. The model parameters are identified......The high energy consumption of popularly used distillation columns has motivated development of energytracking dynamic models with the ultimate objective for potential better energy and quality control of these separation facilities. A dynamic model being able to explicitly describe both...

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bennett, J M

1884-06-03

The invention relates to retorts for the destructive distillation of shale, dross, and other carbonaceous or oleaginous materials, and for the distillation and carbonization of sawdust, shavings, tan bark, and the like. The material is fed from a trapped hopper on a series of trays or casings of cast iron or other material, separated by flue spaces and arranged in a tier round a vertical rotating shaft passing through tubular pieces cast on the casings. The shaft is fitted with arms which carry stirring-blades so disposed that the material is shifted from side to side and slowly fed towards the ducts through which it passes to the casing next below, and is finally withdrawn from the apparatus by a pipe, which may be trapped or otherwise. Furnace gases are admitted through openings in the enclosing brickwork having settings to support the casings, the lowermost of which may be fitted below the inlet for furnace gases and their contents cooled by the circulation of cold water round them. The gaseous or volatile products of distillation pass to a condenser by means of openings and the pipe, which may be formed in sections to obtain access to the casings, or doors may be provided for this purpose. The ducts may be arranged alternately at the edge and center of the casings, which may be jacketed, and heated air or steam may be employed instead of furnace gases. Means may also be provided for admitting superheated steam into one or more of the casings.

Mise au point d'un nouvel appareil de "distillation isotherme" Disterm Development of Distherm, a New Isothermal Distillation Apparatus

Directory of Open Access Journals (Sweden)

Mouton M.

2006-11-01

Full Text Available Les études analytiques de distillats pétroliers d'intervalles d'ébullition élevés doivent être réalisées sur des produits préparés dans des conditions de distillation extrêmement douces, de manière à conserver intactes toutes les espèces chimiques initialement contenues dans le pétrole brut en l'état. Pour répondre à cet objectif, le Comité de Distillation du GEC (Groupe d'Études Concertées sur l'analyse des fractions lourdes du pétrole, réunissant Compagnie Francaise de Raffinage (CFR, Société Nationale Elf Aquitaine (SNEA et Institut Français du Pétrole (IFP a mis au point un schéma de préparation spécial de ces distillats, faisant appel à des techniques de distillation continue, de type « isotherme» et « moléculaire ». Dans ce cadre, le Comité de Distillation du GEC a été amené à développer un nouvel appareillage de distillation x isotherme », permettant de réduire, sans craquage, tout pétrole brut jusqu'à une température maximale comprise entre 350 et 380 °C. On décrit dans cet article ce nouvel ensemble de distillation, ainsi que ses conditions opératoires de fonctionnement. On y donne aussi un aperçu de la précision de la méthode de distillation réalisable avec cet appareil, ainsi que de la qualité de fractionnement obtenu.Enfin, à l'aide de quelques exemples particuliers, on montre que le domaine d'application de l'appareil peut être étendu à des produits autres que des pétroles bruts. Analytical examinations of high-boiling-range petroleum distillates must be made with products prepared under extremely mild distillation conditions so as ta maintain intact all the chemical species initially present in the original crude oil.

7 CFR 160.9 - Destructively distilled wood turpentine.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Destructively distilled wood turpentine. 160.9 Section... REGULATIONS AND STANDARDS FOR NAVAL STORES General § 160.9 Destructively distilled wood turpentine. The designation “destructively distilled wood turpentine” shall refer to the kind of spirits of turpentine...

Solar distillation between a simple and double-glazing

Directory of Open Access Journals (Sweden)

Abderrahmane KHECHEKHOUCHE

2017-12-01

Full Text Available The south-east region of Algeria suffers from a great socio-economic problem that affects a large population. Faced with the unavailability of drinking water, solar distillation; which appears to be a suitable and inexpensive solution; was adopted by local researchers. Improving the productivity of a solar greenhouse distiller is the subject of several researches in the world. As it is well known, distiller with simple glazing is wildly studied but unfortunately has feeble efficiency. Double glazing is a method that increases the efficiency of a flat solar collector. The idea is to use the same technique on a single-slope solar distiller (50 x 50 cm. Two glass plates separated by 1 cm between them air is trapped. Experience shows that this technique has a negative effect on the productivity of the distiller with a rate of 88.63%; it means 9 times. So double glazing is not recommended in the single slope solar distiller.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Irvine, R

1884-04-04

In obtaining paraffin by distillation of shales, etc., containing sulfur, the steam used for heating is charged with ammonia or ammonium carbonate in suspension. This prevents the sulfur from decomposing the paraffin. The ammonia, etc., may also be used alone or in solution in water.

Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

Energy Technology Data Exchange (ETDEWEB)

Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-12-01

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N{sub 2} and H{sub 2}-D{sub 2} distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N{sub 2} distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H{sub 2}, HD, D{sub 2}, HT, DT, T{sub 2}) distillation column showed good performance after comparison with the result of a JAERI code, and a H{sub 2}-D{sub 2} distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H{sub 2}-D{sub 2} distillation process was suggested. A feasibility on modification of H{sub 2}-D{sub 2} distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author).

Distillation process using microchannel technology

Science.gov (United States)

Tonkovich, Anna Lee [Dublin, OH; Simmons, Wayne W [Dublin, OH; Silva, Laura J [Dublin, OH; Qiu, Dongming [Carbondale, IL; Perry, Steven T [Galloway, OH; Yuschak, Thomas [Dublin, OH; Hickey, Thomas P [Dublin, OH; Arora, Ravi [Dublin, OH; Smith, Amanda [Galloway, OH; Litt, Robert Dwayne [Westerville, OH; Neagle, Paul [Westerville, OH

2009-11-03

The disclosed invention relates to a distillation process for separating two or more components having different volatilities from a liquid mixture containing the components. The process employs microchannel technology for effecting the distillation and is particularly suitable for conducting difficult separations, such as the separation of ethane from ethylene, wherein the individual components are characterized by having volatilities that are very close to one another.

Performance indicators of bioethanol distillation

International Nuclear Information System (INIS)

Marriaga, Nilson

2009-01-01

The increase of biofuels demand accelerates the construction of new production plants and technological improvements in the process so the development of versatile tools for evaluating alternatives becomes an undeniable challenge. It was established through heuristic rules, thermodynamic analysis and simulation computer the energy consumption and performance indicators that govern, from fermented mash (ethanol 8.5 % v/v), the distillation of various capacities for bioethanol production: 20, 60, 100 and 150 KLD (kiloliters / day) through Aspen PlusTM simulator. It was found that the distillation demand nearly 30% of heat that would be obtained by burning alcohol fuel produced thus it is necessary the use of raw materials that generate enough biomass to produce the steam required. In addition, correlations were found to allow for easy diameters of distillation columns in terms of production capacity.

Apparatus for distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Carthaus, E; von Rittersberg, K; Abraham, A

1917-05-03

Apparatus for dry distillation of bituminous material, such as oil shale and brown coal with simultaneous fractional separation of the distillate, consists in the fact, that the domed water-cooled condenser, arranged above the conveyer carrying it, is divided by double vertical partitions in the chamber.

7 CFR 58.331 - Starter distillate.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Starter distillate. 58.331 Section 58.331 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.331 Starter distillate. The refined flavor components when used to flavor butter and related...

Advanced purification of petroleum refinery wastewater by catalytic vacuum distillation.

Science.gov (United States)

Yan, Long; Ma, Hongzhu; Wang, Bo; Mao, Wei; Chen, Yashao

2010-06-15

In our work, a new process, catalytic vacuum distillation (CVD) was utilized for purification of petroleum refinery wastewater that was characteristic of high chemical oxygen demand (COD) and salinity. Moreover, various common promoters, like FeCl(3), kaolin, H(2)SO(4) and NaOH were investigated to improve the purification efficiency of CVD. Here, the purification efficiency was estimated by COD testing, electrolytic conductivity, UV-vis spectrum, gas chromatography-mass spectrometry (GC-MS) and pH value. The results showed that NaOH promoted CVD displayed higher efficiency in purification of refinery wastewater than other systems, where the pellucid effluents with low salinity and high COD removal efficiency (99%) were obtained after treatment, and the corresponding pH values of effluents varied from 7 to 9. Furthermore, environment estimation was also tested and the results showed that the effluent had no influence on plant growth. Thus, based on satisfied removal efficiency of COD and salinity achieved simultaneously, NaOH promoted CVD process is an effective approach to purify petroleum refinery wastewater. Copyright 2010 Elsevier B.V. All rights reserved.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Allison, C A

1906-05-22

The invention relates to an apparatus in which the destructive distillation or coking of coal, peat, shale, etc., is carried out by means of a current of hot gases at a temperature of 700--800/sup 0/F., as described in Specification No. 11,925, A.D. 1906.

Wine distillates: practical operating recipe formulation for stills.

Science.gov (United States)

Osorio, Daniel; Pérez-Correa, J Ricardo; Biegler, Lorenz T; Agosin, Eduardo

2005-08-10

Consumer perceptions of flavors are associated with the chemical composition of foods. However, consumer preferences change; therefore, it is necessary for food manufacturers to be able to adapt their products. Unlike in aged spirits, the chemical composition of young spirits is determined during distillation; therefore, this is where distillers must tailor their operating recipes to the new trends. Even for an experienced distiller, the complexity of the process makes adapting the operating recipe far from straightforward. In this study, we developed a methodology for generating practical recipes that makes use of computer simulations and optimization techniques. We used Pisco Brandy, a young Muscat wine distillate from Chile and Peru as our case study. Even so, because our methodology is independent of the chemical composition of the broth, it can be applied throughout the industry. Drawing on the experience and preferences of industry enologists, we designed a preferred distillate and used our methodology to obtain the appropriate recipe. This recipe was validated in lab scale experiments, and we obtained a much closer distillate to the desired prescription than commercial products.

Vacuum distillation of plutonium pyrochemical salts

International Nuclear Information System (INIS)

Bourges, Gilles; Faure, S.; Fiers, B.; Saintignon, S.; Lemoine, O.; Cardona-Barrau, D.; Devillard, D.

2012-01-01

A pyrochemical process is developed to upgrade the safety of plutonium spent salts interim storage. The feed material, consisting of alkali or alkali-earth chlorides containing various Pu and Am species, is first oxidized to convert the actinides into oxides. Then the chlorides are removed by vacuum distillation which requires temperature from 750 degrees C to 1100 degrees C. After a comprehensive R and D program, full-scale equipment was built to test the distillation of active salts. Tests with NaCl/KCl oxidized spent salt give decontamination factor of chlorides higher than 20000. The distilled salt meets the radiologic requirements to be discarded as low level waste. (authors)

Distilling oil shale

Energy Technology Data Exchange (ETDEWEB)

Crozier, R H

1923-04-18

In the fractional distillation of oils from oil shale and similar materials the charge is passed continuously through a vertical retort heated externally by hot combustion gases in flues and internally by the passage of these gases through flues passing through the retort so that zones of increasing temperature are maintained. A vapor trap is provided in each zone having an exit pipe leading through a dust trap to a condenser. The bottoms of the conical vapor traps are provided with annular passages perforated to permit of steam being sprayed into the charge to form screens which prevent the vapors in different zones from mingling, and steam may also be introduced through perforations in an annular steam box. Dampers are provided to control the passage of the heating gases through the flues independently.

Method and arrangement of distillation of shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1920-03-29

A method is given of distilling shale and other bituminous materials utilizing the heat from the combustion of the residue, possibly with additional heat from other fuels. It is characterized by the shale, which is arranged in layers, being first submitted to a process of distillation utilizing the heat mentioned, and at the same time recovering the products of distillation, and second the shale being burned without disturbing the layers to any appreciable extent. The patent has 16 more claims.

Membrane distillation against a pressure difference

NARCIS (Netherlands)

Keulen, L.; Ham, L.V. van der; Kuipers, N.J.M.; Hanemaaijer, J.H.; Vlugt, T.J.H.; Kjelstrup, S.

2017-01-01

Membrane distillation is an attractive technology for production of fresh water from seawater. The MemPower® concept, studied in this work, uses available heat (86 °C) to produce pressurized water (2.2 bar and 46 °C) by membrane distillation, which again can be used to power a turbine for

Evolution of Volatile Compounds during the Distillation of Cognac Spirit.

Science.gov (United States)

Awad, Pierre; Athès, Violaine; Decloux, Martine Esteban; Ferrari, Gérald; Snakkers, Guillaume; Raguenaud, Patrick; Giampaoli, Pierre

2017-09-06

Cognac wine spirit has a complex composition in volatile compounds which contributes to its organoleptic profile. This work focused on the batch distillation process and, in particular, on volatile compounds specifically produced by chemical reactions during the distillation of Cognac wine spirit, traditionally conducted in two steps with charentais pot stills. The aim of this study was to characterize these volatile compounds formed during distillation. Sampling has been performed on the distillates and inside the boiler during a typical Cognac distillation. The analysis of these samples allowed us to perform a mass balance and to point out several types of volatile compounds whose quantities strongly increased during the distillation process. These compounds were distinguished by their chemical family. It has been found that the first distillation step was decisive for the formation of volatile compounds. Moreover, 2 esters, 3 aldehydes, 12 norisoprenoids, and 3 terpenes were shown to be generated during the process. These results suggest that some volatile compounds found in Cognac spirit are formed during distillation due to chemical reactions induced by high temperature. These findings give important indications to professional distillers in order to enhance the product's quality.

Energy savings in distillation via identification of useful configurations

Science.gov (United States)

Shah, Vishesh Hemanshu

Recent market and environmental forces require the rapid development of better and cheaper separation process solutions. Especially for multicomponent mixtures, there are several feasible separation process solutions differing significantly in cost and energy consumption in spite of carrying out the same overall process. Therefore a systematic method to identify and design optimal multicomponent separation sequences is needed instead of relying on the inventive activity of a few experienced engineers. Even for a commonly perceived "mature" technology such as distillation, until recently there has been an absence of systematic methods to (i) elucidate all possible separation configurations and to (ii) identify energy efficient candidates. This research aims to address these needs. In this work, we focus on the continuous distillation of non-azeotropic mixtures into n distinct composition final product streams. We develop a computationally efficient and easy-to-use mathematical framework to generate all the basic distillation configurations that use exactly (n-1) distillation columns to carry out this n-component separation. We extend the framework to generate all the additional distillation configurations with thermal coupling. We observe that the search space of distillation configurations grows very rapidly as the number of product streams increases. For instance, for a mixture to be separated into 4 product streams, we can choose from 18 basic configurations and 134 additional configurations with thermal coupling; while for a mixture to be separated into 8 product streams, we can choose from 15,767,207 basic configurations and 29,006,926,681 additional configurations with thermal coupling. The next challenge for a process engineer is to be able to quickly prune the search space to a handful of attractive energy efficient candidates that can be studied in greater detail. To this effect, we develop a quick screening optimization tool that identifies configurations

Membrane distillation against a pressure difference

NARCIS (Netherlands)

Keulen, L.; van der Ham, LV; Kuipers, N.J.M.; Hanemaaijer, J.H.; Vlugt, T.J.H.; Kjelstrup, S

2017-01-01

Membrane distillation is an attractive technology for production of fresh water from seawater. The MemPower®MemPower® concept, studied in this work, uses available heat (86 °C) to produce pressurized water (2.2 bar and 46 °C) by membrane distillation, which again can be used to power a turbine for

Process of distillation of oil shale

Energy Technology Data Exchange (ETDEWEB)

Saxton, A L

1968-08-16

In an oil-shale distillation apparatus with a single retort, in which separate zones of preheating, distillation, combustion, and cooling are maintained, the operation is conducted at a presssure higher than the atmospheric pressure, preferably at a gage pressure between about 0.35 and 7.0 bars. This permits increasing the capacity of the installation.

[Distiller Yeasts Producing Antibacterial Peptides].

Science.gov (United States)

Klyachko, E V; Morozkina, E V; Zaitchik, B Ts; Benevolensky, S V

2015-01-01

A new method of controlling lactic acid bacteria contamination was developed with the use of recombinant Saccharomyces cerevisiae strains producing antibacterial peptides. Genes encoding the antibacterial peptides pediocin and plantaricin with codons preferable for S. cerevisiae were synthesized, and a system was constructed for their secretory expression. Recombinant S. cerevisiae strains producing antibacterial peptides effectively inhibit the growth of Lactobacillus sakei, Pediacoccus pentasaceus, Pediacoccus acidilactici, etc. The application of distiller yeasts producing antibacterial peptides enhances the ethanol yield in cases of bacterial contamination. Recombinant yeasts producing the antibacterial peptides pediocin and plantaricin can successfully substitute the available industrial yeast strains upon ethanol production.

Low temperature distillation

Energy Technology Data Exchange (ETDEWEB)

Vandegrift, J N; Postel, C

1929-04-09

To recover gas, oil tars, and coked residues by low temperature distillation from bituminous coals, lignites, oil shales, and the like, the raw material is fed from a hopper into a rotary retort which is zonally heated, the temperature being greatest at the discharge end. The material is heated first to a relatively low temperature, thereby removing the moisture and lighter volatiles which are withdrawn through a pipe by the suction of a pump, while the higher boiling point volatiles and fixed gases are withdrawn by suction through an outlet from the higher temperature zone. The vapors withdrawn from the opposite ends of the retort pass through separate vapor lines and condensers, and the suction in each end of the retort, caused by the pumps, is controlled by valves, which also control the location of the neutral point in the retort formed by said suction. Air and inert gas may be introduced into the retort from pipe and stack respectively through a pipe, and steam may be admitted into the high temperature zone through a pipe.

Hydrodeoxygenation of oxidized distilled bio-oil for the production of gasoline fuel type

International Nuclear Information System (INIS)

Luo, Yan; Guda, Vamshi Krishna; Hassan, El Barbary; Steele, Philip H.; Mitchell, Brian; Yu, Fei

2016-01-01

Highlights: • Oxidation had more influence on the yield of total hydrocarbons than distillation. • The highest total hydrocarbon yield was obtained from oxidized distilled bio-oil. • The 2nd-stage hydrocarbons were in the range of gasoline fuel boiling points. • The main products for upgrading of oxidized bio-oil were aliphatic hydrocarbons. • The main products for upgrading of non-oxidized bio-oil were aromatic hydrocarbons. - Abstract: Distilled and oxidized distilled bio-oils were subjected to 1st-stage mild hydrodeoxygenation and 2nd-stage full hydrodeoxygenation using nickel/silica–alumina catalyst as a means to enhance hydrocarbon yield. Raw bio-oil was treated for hydrodeoxygenation as a control to which to compare study treatments. Following two-stage hydrodeoxygenation, four types of hydrocarbons were mainly comprised of gasoline and had water contents, oxygen contents and total acid numbers of nearly zero and higher heating values of 44–45 MJ/kg. Total hydrocarbon yields for raw bio-oil, oxidized raw bio-oil, distilled bio-oil and oxidized distilled bio-oil were 11.6, 16.2, 12.9 and 20.5 wt.%, respectively. The results indicated that oxidation had the most influence on increasing the yield of gasoline fuel type followed by distillation. Gas chromatography/mass spectrometry characterization showed that 66.0–76.6% of aliphatic hydrocarbons and 19.5–31.6% of aromatic hydrocarbons were the main products for oxidized bio-oils while 35.5–38.7% of aliphatic hydrocarbons and 58.2–63.1% of aromatic hydrocarbons were the main products for non-oxidized bio-oils. Both aliphatic and aromatic hydrocarbons are important components for liquid transportation fuels and chemical products.

Retorts for distilling carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Lutz, H E

1921-09-12

A retort for distilling carbonaceous material is described in which a mass of such material is retained in a pocket formed between an outer wall and an internal wall which is perforated to permit the free escape of distilled products, the retorts having heating means that directly heat the retort but are so related to the pocket that the material therein is heated indirectly and simultaneously from all sides entirely by heat conducted thereto by the walls.

Three methods to distill multipartite entanglement over bipartite noisy channels

International Nuclear Information System (INIS)

Lee, Soojoon; Park, Jungjoon

2008-01-01

We first assume that there are only bipartite noisy qubit channels in a given multipartite system, and present three methods to distill the general Greenberger-Horne-Zeilinger state. By investigating the methods, we show that multipartite entanglement distillation by bipartite entanglement distillation has higher yield than ones in the previous multipartite entanglement distillations

Impact of Grape Varieties on Wine Distillates Flavour

Directory of Open Access Journals (Sweden)

Mara Banović

2002-01-01

Full Text Available Aroma is a phenomenon that occurrs when food and live organism mutually react during the process of consumption. Many factors influence the making of aroma of wine distillates (e.g. cognac during the technological process of distillation. It is extremely difficult to bring an objective judgement on the influence of individual factors since aroma is very subjective in its nature. The possibility of objective assessment of the influence of grape varieties on wine distillate was performed in this work using a computer in processing the results of cromatographic analyses of aroma substances. The given results were verified by sensor analyses. The achieved results have shown that mathematical model for calculating aroma chromatogram similarity can be successfully used for objective assessment of the influence of individual factors on aroma of wine distillates and that grape varieties have significant impact on aroma and the quality of wine distillates.

Energy consumption maps for quaternary distillation sequences

DEFF Research Database (Denmark)

Gomez-Castro, F.I.; Ramírez-Vallejo, N.E.; Segovia-Hernandez, J.G.

2016-01-01

Thermally coupled distillation columns represent a very interesting option for the intensification of distillation systems in order to reduce the energy consumption, and, as a consequence, the environmental impact of the separation process. Several thermally coupled distillation schemes can......, for a given mixture, depends on the nature of the mixture, usually quantified for ternary mixtures through the ease of separation index (ESI), and also on the feed composition. As can be noticed, the size of the design and optimization problem increases when these variables are considered in the generation...

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Byrom, W A; Bennett, J A.B.

1884-02-22

Effecting the separation of the various products of the distillation of coal, shale, etc., by taking advantage of the graduated temperature of successive portions of the length of mechanical retorts is described. The substances entering from the hopper are gradually heated in their progress and give off a series of products in their order of volatilization, which pass from openings in the retort through a series of ascension pipes into collecting-vessels. The vessels are designed to contain different portions of the distillate and are sealed against the escape of uncondensed vapor or gas by the condensed liquid. Each of the ascension pipes communicates above its vessel with a common pipe to convey away permanent gases. The flues for heating the retort may be so arranged as to give the greatest heat at the end farthest from the point of entrance, or the stages of heat may be self-regulated by the time necessary for the material to acquire heat as it travels. If necessary the pipes may be fitted with refrigerating-appliances.

Fractional distillation of oil

Energy Technology Data Exchange (ETDEWEB)

Jones, L D

1931-10-31

A method of dividing oil into lubricating oil fractions without substantial cracking by introducing the oil in a heated state into a fractionating column from which oil fractions having different boiling points are withdrawn at different levels, while reflux liquid is supplied to the top of the column, and additional heat is introduced into the column by contacting with the oil therein a heated fluid of higher monlecular weight than water and less susceptible to thermal decomposition than is the highest boiling oil fraction resulting from the distillation, or of which any products produced by thermal decomposition will not occur in the highest boiling distillate withdrawn from the column.

A comparative evaluation of nitrogen compounds in petroleum distillates

Energy Technology Data Exchange (ETDEWEB)

Singh, Dheer; Chopra, Anju; Patel, Mitra Bhanu; Sarpal, Amarjit Singh [Indian Oil Corporation Limited, Faridabad (India). Research and Development Centre

2011-07-15

Although the concentration of nitrogen compounds in crude oil is relatively low, they can become more concentrated in petroleum distillates and poison the catalysts used in refining processes. They cause undesirable deposits, color formation and odor in products; they also contribute to air pollution and some are highly carcinogenic. The poisoned catalyst becomes deactivated for hydrodesulfurization and unable to remove sulfur from middle distillates. In order to understand the effect on catalytic processes, it is desirable to identify the nitrogen compounds in various petroleum distillates. This paper compares the nitrogen species profiles in different petroleum distillates using a nitrogen chemiluminescence detector. In addition, four different petroleum distillate samples from different refineries were analyzed to find the variation in their nitrogen profiles. The nitrogen compounds in petroleum distillate samples were identified as anilines, quinolines, indoles, and carbazoles and their alkyl derivatives. Quantitation was carried out against known reference standards. The quantitative data were compared to the total nitrogen content determined by elemental analysis. (orig.)

Asymptotic speedups, bisimulation and distillation (Work in progress)

DEFF Research Database (Denmark)

Jones, Neil; Hamilton, G. W.

2015-01-01

Distillation is a fully automatic program transformation that can yield superlinear program speedups. Bisimulation is a key to the proof that distillation is correct, i.e., preserves semantics. However the proof, based on observational equivalence, is insensitive to program running times....... This paper shows how distillation can give superlinear speedups on some “old chestnut” programs well-known from the early program transformation literature: naive reverse, factorial sum, and Fibonacci....

Advanced Control Test Operation (ACTO) facility

International Nuclear Information System (INIS)

Ball, S.J.

1987-01-01

The Advanced Control Test Operation (ACTO) project, sponsored by the US Department of Energy (DOE), is being developed to enable the latest modern technology, automation, and advanced control methods to be incorporated into nuclear power plants. The facility is proposed as a national multi-user center for advanced control development and testing to be completed in 1991. The facility will support a wide variety of reactor concepts, and will be used by researchers from Oak Ridge National Laboratory (ORNL), plus scientists and engineers from industry, other national laboratories, universities, and utilities. ACTO will also include telecommunication facilities for remote users

27 CFR 26.40 - Marking containers of distilled spirits.

Science.gov (United States)

2010-04-01

... spirits. The distiller, rectifier, or bottler shall serially number each case, barrel, cask, or similar... the container, the distiller, rectifier, or bottler shall plainly print, stamp, or stencil with... barrel, cask or similar container or on one side of each case, as follows: (a) The name of the distiller...

Cascade Distillation Subsystem Development: Early Results from the Exploration Life Support Distillation Technology Comparison Test

Science.gov (United States)

Callahan, Michael R.; Patel, Vipul; Pickering, Karen D.

2010-01-01

In 2009, the Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell International, Torrance, California) was assessed in the National Aeronautics and Space Administration (NASA) Exploration Life Support (ELS) distillation comparison test. The purpose of the test was to collect data to support down-selection and development of a primary distillation technology for application in a lunar outpost water recovery system. The CDS portion of the comparison test was conducted between May 6 and August 19, 2009. The system was challenged with two pretreated test solutions, each intended to represent a feasible wastewater generated in a surface habitat. The 30-day equivalent wastewater loading volume for a crew of four was intended to be processed for each wastewater solution. Test Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. Test Solution 2 contained the addition of human-generated hygiene wastewater to the solution 1 waste stream components. Approximately 1500 kg of total wastewater was processed through the CDS during testing. Respective recoveries per solution were 93.4 +/- 0.7 and 90.3 +/- 0.5 percent. The average specific energy of the system during testing was calculated to be less than 120 W-hr/kg. The following paper provides detailed information and data on the performance of the CDS as challenged per the ELS distillation comparison test.

Distillation modeling for a uranium refining process

International Nuclear Information System (INIS)

Westphal, B.R.

1996-01-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed open-quotes cathode processingclose quotes. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process

Distillation modeling for a uranium refining process

Energy Technology Data Exchange (ETDEWEB)

Westphal, B.R.

1996-03-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed {open_quotes}cathode processing{close_quotes}. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process.

Design and construction of a Fresnel linear distiller

International Nuclear Information System (INIS)

Saettone, E.

2014-01-01

It was designed a Fresnel linear distiller based on optical calculations obtained from taking into account Lima's latitude value, Earth inclination angle and heat absorber cavity's dimensions. The 5.6 m 2 reflective surface concentrator of the distiller was constructed with 32 plane rectangular mirrors; the heat absorber cavity was made with a rectangular blackened aluminum tube 1 m long and installed 2.5 m over the plane of mirrors. The Fresnel linear distiller was installed at the University of Lima and experimental tests were performed during no cloudy summer days. There were measured ambient temperature, heat absorber cavity temperature, radiant flux and fresh water volume. From this, it was obtained a production of 0.89 liters/hour and 0.79 L/m 2 , and it was calculated a total performance of 34.5% in desalting sea water. Finally, it is presented a comparison between Fresnel linear distiller (FLD) and parabolic trough distiller (PTD) with similar dimensions and characteristics. It is obtained that the last one produced almost 32% more fresh water than the former, but at the same time, the FLD is almost 20% cheaper than PTD. However, water cost production with both distillers using is almost the same. (author)

Identification of Distillation Process Dynamics Comparing Process Knowledge and Black Box Based Approaches

DEFF Research Database (Denmark)

Rasmussen, Knud H; Nielsen, C. S.; Jørgensen, Sten Bay

1990-01-01

A distillation plant equipped with a heat pump separates a mixture of isopropanol and methanol. The mixture contains some water as impurity. The model development aims at dual composition control design, where top and bottom compositions should follow the setpoints, and disturbances should...... obtained in closed loop operation of the distillation plant. In the present work, the two approaches are compared in terms of how well the model fits, and predicts the data, the conditioning of the model parameter estimation, and convenience of usage....

Investigation of non-volatile additives on the process of distillation of hydrocarbon mixtures

Directory of Open Access Journals (Sweden)

М.Б. Степанов

2009-02-01

Full Text Available  The given results of researches of influence of nonvolatile additives on processes of distillation of individual hydrocarbons and their mixes, including petroleum and mineral oil. With the help of the developed computer system of the continuous control of distillation it is shown, that at the presence of small amounts of the additive decrease of temperature of the beginning of boiling of hydrocarbons is observed, their speeds of banish and exits of light fuel mineral oil grow during initial oil refining

The advanced controls program at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Knee, H.E.; White, J.D.

1990-01-01

The Oak Ridge National Laboratory (ORNL), under sponsorship of the US Department of Energy (DOE), is conducting research that will lead to advanced, automated control of new liquid-metal-reactor (LMR) nuclear power plants. Although this program of research (entitled the ''Advanced Controls Program'') is focused on LMR technology, it will be capable of providing control design, test, and qualification capability for other advanced reactor designs (e.g., the advanced light water reactor [ALWR] and high temperature gas-cooled reactor [HTGR] designs), while also benefiting existing nuclear plants. The Program will also have applicability to complex, non-nuclear process control environments (e.g., petrochemical, aerospace, etc.). The Advanced Controls Program will support capabilities throughout the entire plant design life cycle, i.e., from the initial interactive first-principle dynamic model development for the process, systems, components, and instruments through advanced control room qualification. The current program involves five principal areas of research activities: (1) demonstrations of advanced control system designs, (2) development of an advanced controls design environment, (3) development of advanced control strategies, (4) research and development (R ampersand D) in human-system integration for advanced control system designs, and (5) testing and validation of advanced control system designs. Discussion of the research in these five areas forms the basis of this paper. Also included is a description of the research directions of the program. 8 refs

Driving Force Based Design of Cyclic Distillation

DEFF Research Database (Denmark)

Nielsen, Rasmus Fjordbak; Huusom, Jakob Kjøbsted; Abildskov, Jens

2017-01-01

with mixed phase feeds. A range of binary test cases, benzene toluene, methanol water, and ethanol water, are evaluated. The advantage of the design approach in cyclic distillation is shown to be analogous to the advantages obtained in conventional continuous distillation, including a minimal utility...

Features investigation of corrosion-electrochemical behaviour of Al-alloys for engineering an effective protection of the water-distillings setups

International Nuclear Information System (INIS)

Fokin, M.N.; Lomakina, S.V.; Tselykh, O.G.; Shatova, T.S.; Trubetskaya, L.F.

1993-01-01

The problem of aluminium alloy application in distilling setups is studied. Investigation into the features of corrosion and electrochemical behaviour of aluminium alloys under sea water distillation allows one to reveal the main control factors and to propose optimal alloy compositions capable of providing the safe setup operation on their base. Preliminary treatment in tungsten and molybdenum isopolycompound solutions is proposed which reduces sedimentation which in its turn is very important for distilling setups

Chronic consumption of distilled sugarcane spirit induces anxiolytic-like effects in mice.

Science.gov (United States)

Sena, Maria Clecia P; Nunes, Fabíola C; Salvadori, Mirian G S Stiebbe; Carvalho, Cleyton Charles D; Morais, Liana Clebia S L; Braga, Valdir A

2011-01-01

Chronic ethanol consumption is a major public health problem throughout the world. We investigated the anxiolytic-like effects and the possible ever injury induced by the chronic consumption of ethanol or sugarcane spirit in mice. Adult mice were exposed to a two-bottle free-choice paradigm for 6 weeks. The mice in Group A (n = 16) had access to sugarcane spirit + distilled water, the mice in Group B (n = 15) had access to ethanol + distilled water, and the mice in Group C (control, n = 14) had access to distilled water + distilled water. The ethanol content in the beverages offered to Groups A and B was 2% for the first week, 5% for the second week and 10% for the remaining four weeks. At the end of the experimental period, the mice were evaluated using the elevated-plus maze and the hole-board test to assess their anxiety-related behaviors. We also determined the serum aspartate aminotransferase and alanine aminotransferase levels. In the elevated-plus maze, the time spent in the open arms was increased in the mice exposed to chronic ethanol (32 ± 8 vs. 7 ± 2 s, n = 9) or sugarcane spirit (36 ± 9 vs. 7 ± 2 s, n = 9) compared to the controls. In the hole-board test, the mice exposed to ethanol or sugarcane spirit displayed increases in their head-dipping frequency (16 ± 1 for the control group, 27 ± 2 for the ethanol group, and 31 ± 3 for the sugarcane-spirit group; n = 9 for each group). In addition, the mice exposed to sugarcane spirit displayed an increase in the aspartate aminotransferase / alanine aminotransferase ratio compared to the ethanol group (1.29 ± 0.17 for the control group and 2.67 ± 0.17 for the sugarcane spirit group; n = 8 for each group). The chronic consumption of sugarcane-spirit produces liver injury and anxiolytic-like effects and the possible liver injury in mice.

Chronic consumption of distilled sugarcane spirit induces anxiolytic-like effects in mice

Directory of Open Access Journals (Sweden)

Maria Clecia P. Sena

2011-01-01

Full Text Available OBJECTIVE: Chronic ethanol consumption is a major public health problem throughout the world. We investigated the anxiolytic-like effects and the possible ever injury induced by the chronic consumption of ethanol or sugarcane spirit in mice. METHOD: Adult mice were exposed to a two-bottle free-choice paradigm for 6 weeks. The mice in Group A (n = 16 had access to sugarcane spirit + distilled water, the mice in Group B (n = 15 had access to ethanol + distilled water, and the mice in Group C (control, n = 14 had access to distilled water + distilled water. The ethanol content in the beverages offered to Groups A and B was 2% for the first week, 5% for the second week and 10% for the remaining four weeks. At the end of the experimental period, the mice were evaluated using the elevated-plus maze and the hole-board test to assess their anxiety-related behaviors. We also determined the serum aspartate aminotransferase and alanine aminotransferase levels. RESULTS: In the elevated-plus maze, the time spent in the open arms was increased in the mice exposed to chronic ethanol (32 + 8 vs. 7 + 2 s, n = 9 or sugarcane spirit (36 + 9 vs. 7 + 2 s, n = 9 compared to the controls. In the hole-board test, the mice exposed to ethanol or sugarcane spirit displayed increases in their head-dipping frequency (16 + 1 for the control group, 27 + 2 for the ethanol group, and 31 + 3 for the sugarcane-spirit group; n = 9 for each group. In addition, the mice exposed to sugarcane spirit displayed an increase in the aspartate aminotransferase / alanine aminotransferase ratio compared to the ethanol group (1.29 + 0.17 for the control group and 2.67 + 0.17 for the sugarcane spirit group; n = 8 for each group. CONCLUSION: The chronic consumption of sugarcane-spirit produces liver injury and anxiolytic-like effects and the possible liver injury in mice.

Vapor compression distiller and membrane technology for water revitalization

Science.gov (United States)

Ashida, A.; Mitani, K.; Ebara, K.; Kurokawa, H.; Sawada, I.; Kashiwagi, H.; Tsuji, T.; Hayashi, S.; Otsubo, K.; Nitta, K.

1987-01-01

Water revitalization for a space station can consist of membrane filtration processes and a distillation process. Water recycling equipment using membrane filtration processes was manufactured for ground testing. It was assembled using commercially available components. Two systems for the distillation are studied: one is absorption type thermopervaporation cell and the other is a vapor compression distiller. Absorption type thermopervaporation, able to easily produce condensed water under zero gravity, was investigated experimentally and through simulated calculation. The vapor compression distiller was studied experimentally and it offers significant energy savings for evaporation of water.

A Modelling Framework for Conventional and Heat Integrated Distillation Columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2013-01-01

of hydrocarbons such as separations of equimolar mixtures of benzene/toluene or propane/propene described by simple models, a generic, modular, model framework is presented in this work. At present, the framework is able to describe a conventional distillation column, a mechanical vapor recompression column......Diabatic operation of distillation columns can lead to signicant reductions in energy utilization and operation cost compared to conventional (adiabatic) distillation columns, at an expense of an increased complexity of design and operation. The earliest diabatic distillation conguration dates back...... to the late 70s, and various dierent congurations have appeared since. However, at present, no full-scale diabatic distillation columns are currently operating in the industry. Current studies related to alternative distillation congurations report very dierent gures for potential energy savings which...

Transient behavior of enrichment of tritium water in adsorption-distillation column

International Nuclear Information System (INIS)

Fukada, Satoshi

2006-01-01

Enrichment of tritium in an adsorption-distillation column was experimentally investigated under the two processes of simple distillation and total-reflux distillation. Adsorption of water on silica-gel pellets enhanced the total isotope separation factor in the water distillation column. The transient behavior of tritium enrichment was analyzed using material balance equations of tritium and water in each cell with a height corresponding to HETP. The experimental transient behavior was well simulated by the material balance equations with additional assumptions on vapor and liquid flow rates regardless of the different processes of simple distillation and total-reflux distillation. (author)

Hetero-azeotropic distillation: combining fungal dehydration and lipid extraction.

Science.gov (United States)

Tough, A J; Isabella, B L; Beattie, J E; Herbert, R A

2000-01-01

A low-cost single-stage laboratory process combining fungal dehydration and lipid extraction was compared with a traditional two-stage method employing freeze-drying and subsequent mechanical disruption in the presence of solvent. The ability of a number of organic solvents to form hetero-azeotropes with water was exploited. Chloroform, cyclohexane and hexane were assessed in their abilities to both dry and extract lipid from the oleaginous phycomycete Mortierella alpina (ATCC 32222). Drying rate and lipid extraction were maximised under conditions that prevented fungal agglomeration. The total processing time was limited by the rate of dehydration rather than by the rate of lipid extraction. In all cases azeotropic distillation facilitated a greater rate of dehydration than was possible with freeze-drying. A consequent reduction in overall processing time was observed. Uniquely, both the solvent used and the mode of mixing employed controlled the morphology of the aggregates formed during distillation. In combination with mild mixing chloroform discouraged agglomeration whereas cyclohexane and hexane promoted aggregation. Successful lipid extraction was dependent on the use of dry biomass rather than on the application of heat to effect distillation. Neither the application of heat nor the solvent employed had any significant effect on the lipid composition of the extracted oil.

Process and apparatus to distil petroleum. Verfahren und Vorrichtung zur Erdoel-Destillation

Energy Technology Data Exchange (ETDEWEB)

Buchenau, R.; Fauser, F.; Fischer, W.

1982-12-23

In a process to distil petroleum the raw petroleum is distilled in the first instance at atmospheric pressure to separate the low-boiling components and subsequently under vacuum to separate the remaining components. The vacuum distillation is carried out as a flash distillation using a shortway distiller.

Waste acid/metal solution reduction and recovery by vacuum distillation

International Nuclear Information System (INIS)

Jones, E.O.; Wilcox, W.A.; Johnson, N.T.; Bowdish, F.W.

1995-01-01

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions

Vacuum distillation for the separation of LiCl-KCl eutectic salt and cadmium in pyro process

International Nuclear Information System (INIS)

Kwon, S. W.; Park, K. M.; Lee, S. J.; Park, S. B.; Woo, M. S.; Kim, K. R.; Kim, J. G.; Ahn, D. H.; Lee, H. S.

2010-10-01

Electrorefining is a key step in pyro processing. Electrorefining process is generally composed of two recovery steps- a deposit of uranium onto a solid cathode (electrorefining) and then the recovery of the remaining uranium and Tru (Transuranic) elements simultaneously by a liquid cadmium cathode (electrowinning). In this study, distillation experiments of a LiCl-KCl eutectic salt and cadmium metal were carried out to examine the distillation behaviors for the development of the electrorefining and the electrowinning processes. The experimental set-up was composed of a distillation tower with an evaporator and a condenser, vacuum pump, control unit, and an off gas treatment system. The solid-liquid separation prior to distillation of the LiCl-KCl eutectic salt was proposed and found to be feasible for the reduction of the burden of the distillation process. The LiCl-KCl eutectic salt was successfully distilled after the liquid salt separation. Distillation experiments for cadmium metal were also carried out. The apparent evaporation rates of LiCl-KCl eutectic salt and cadmium increased with an increasing temperature. The evaporation behaviors of cadmium metal and cadmium-cerium alloy were compared. Cadmium in the alloy was successfully distilled and separated from cerium. The evaporation rate of cadmium in the alloy was lower than that of cadmium metal. The low evaporation rate of the alloy was probably caused by the formation of an intermetallic compound and the residual salt during the preparation of the alloy. Therefore, the distillation temperature for the distillation of the liquid cathode should be higher than the distillation of cadmium metal. The measured evaporation rates of the eutectic salt and cadmium were compared with the values calculated by a relation based on the kinetics of gases. The theoretical values of the evaporation rate calculated by the Hertz-Langmuir relation were higher than the experimental values. The deviations were compensated for

Advanced Cruise Control (ACC).

NARCIS (Netherlands)

2010-01-01

Advanced Cruise Control (ACC), ook bekend als Adaptive, Active of Intelligent Cruise Control, handhaaft niet alleen de door de bestuurder ingestelde rijsnelheid, maar stemt ook de snelheid van het voertuig af op die van de voorligger. ACC helpt op deze manier om een vooraf bepaalde volgtijd tot de

Teaching and learning distillation in chemistry laboratory courses

Science.gov (United States)

van Keulen, Hanno; Mulder, Theo H. M.; Goedhart, Martin J.; Verdonk, Adri H.

This study investigates the problems chemistry majors have with learning distillation in traditional chemistry laboratory courses. Using an interpretive cyclic research design, we collected and interpreted data, mainly in the form of observation notes and transcriptions of the discourse that takes place during laboratory courses. It was found that students experience numerous problems; these are described and interpreted. We summarize students' problems in four categories: (a) students use an independent component conception; (b) they have insufficient understanding of the properties of vapor; (c) they regard distillation from a physical point of view; and (d) they do not have a practical understanding of thermodynamics. The main origin of these problems was found to lie with the traditional curriculum structure. Lecture courses and textbooks treat distillation in a generalized and decontextualized way, whereas decisions in actual distillations are always based on contextual features. It was found that textbooks and teachers often do not discriminate carefully and explicitly among five different contexts for distillation: organic synthesis, chemical analysis, analytical chemistry, physical chemistry, and preparation of products. Students take the generalized concepts at face value and apply them to all distillations regardless of context. They cannot interpret their observations or make reasoned decisions based on the theoretical framework of a specific context.Received: 2 May 1994; Revised: 14 December 1994;

Advanced Cruise Control (ACC).

NARCIS (Netherlands)

2008-01-01

Advanced Cruise Control (ACC), also known as adaptive or intelligent cruise control, not only maintains the driver-set vehicle speed, but also adjusts the vehicle's speed to that of a preceding vehicle, and helps to maintain a pre-selected headway time to the vehicle ahead. ACC systems can have a

Recycling of Waste Acetone by Fractional Distillation

Science.gov (United States)

Weires, Nicholas A.; Johnston, Aubrey; Warner, Don L.; McCormick, Michael M.; Hammond, Karen; McDougal, Owen M.

2011-01-01

Distillation is a ubiquitous technique in the undergraduate organic chemistry curriculum; the technique dates back to ca. 3500 B.C.E. With the emergence of green chemistry in the 1990s, the importance of emphasizing responsible waste management practices for future scientists is paramount. Combining the practice of distillation with the message…

Some remarks on the carrier distillation method; Quelques remarques sur la methode 'carrier distillation'

Energy Technology Data Exchange (ETDEWEB)

Avni, R; Chaput, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-07-01

The method described by SCRIBNER and MULLIN makes possible the spectrographic analysis of the refractory oxides of uranium and plutonium. It uses a distillation of the elements which is more or less selective. The influence of the carrier is the subject of as many hypotheses as there are parameters involved in the process. The measurements of the arc temperature carried out on the leading edges of the vibration bands and of certain copper lines have made it possible to show the influence of the nature of the carrier and to establish a relationship between the values of the excitation potentials of the atoms and the temperatures produced. Further, this result makes it possible to explain certain contradictions between the principle of a fractional distillation in the arc which is incompatible with the refractory properties of certain elements and their spectrographic sensitivity. (author) [French] La methode decrite par SCRIBNER et MULLIN permet l'analyse spectrographique des oxydes refractaires d'uranium et de plutonium. Elle fait appel a une distillation plus ou moins selective des elements. L'influence de l'entraineur est l'objet d'aussi nombreuses hypotheses que les parametres lies au phenomene. Les mesures de la temperature de l'arc, effectuees sur les tetes de bandes de vibration du cyanogene et certaines raies du cuivre ont permis de montrer l'influence de la nature de l'entraineur et de trouver une relation entre les valeurs des potentiels d'excitation des atomes et les temperatures produites. En outre, ce resultat permet d'expliquer certaines contradictions entre le principe d'une distillation fractionnee dans l'arc incompatible avec les proprietes refractaires de certains elements et leur sensibilite spectrographique. (auteur)

Towards energy efficient distillation technologies – Making the right choice

International Nuclear Information System (INIS)

Kiss, Anton A.; Flores Landaeta, Servando J.; Infante Ferreira, Carlos A.

2012-01-01

In spite of claiming around half of the operational costs of chemical plants, distillation is still the most popular separation technology. Distillation has low thermodynamic efficiency, requiring the input of high quality energy in the reboiler – while rejecting a similar amount of heat at lower temperature, in the condenser. Several heat pump concepts have been proposed to upgrade that thermal energy and reduce the consumption of valuable utilities. Under certain conditions, the energy savings of heat pump assisted distillation is usually around 20–50%. This study proposes a novel selection scheme of energy efficient distillation technologies, with a special focus on heat pumps. The most promising technologies selected are vapor compression, mechanical or thermal vapor recompression, absorption, compression–resorption and thermo-acoustic heat pumps, multi-effect distillation, heat integrated distillation column, cyclic distillation, Kaibel and dividing-wall column. The scheme considers as the main selection criteria the type of separation tasks, product flow and specifications, operating pressure, difference in boiling points, reboiler duty and its temperature level. Moreover, this scheme is very practical, allowing major time and resources savings in the design of eco-efficient processes. -- Highlights: ► Heat pump assisted distillation with energy savings of 20–50%. ► Novel and practical selection scheme of energy efficient distillation technologies. ► Evaluation of promising technologies: VC, MVR, TVR, AHP, CHRP, TAHP, HIDiC, DWC, CyDist. ► Selection criteria include: ΔT b , ΔT lift , P, T reb , Q reb , volatility. ► Design of eco-efficient processes with high COP, and lower TIC and TAC.

ATC-lab(Advanced): an air traffic control simulator with realism and control.

Science.gov (United States)

Fothergill, Selina; Loft, Shayne; Neal, Andrew

2009-02-01

ATC-lab(Advanced) is a new, publicly available air traffic control (ATC) simulation package that provides both realism and experimental control. ATC-lab(Advanced) simulations are realistic to the extent that the display features (including aircraft performance) and the manner in which participants interact with the system are similar to those used in an operational environment. Experimental control allows researchers to standardize air traffic scenarios, control levels of realism, and isolate specific ATC tasks. Importantly, ATC-lab(Advanced) also provides the programming control required to cost effectively adapt simulations to serve different research purposes without the need for technical support. In addition, ATC-lab(Advanced) includes a package for training participants and mathematical spreadsheets for designing air traffic events. Preliminary studies have demonstrated that ATC-lab(Advanced) is a flexible tool for applied and basic research.

A review of the FT distillate pathway in GHGenius

International Nuclear Information System (INIS)

2006-01-01

Fischer-Tropsch (FT) distillates products are now used throughout the world as a commercial fuel. However, lifecycle greenhouse gas (GHG) emissions from FT distillates fuels are higher than diesel fuel produced from crude oil. This paper provided details of a lifecycle analysis of FT distillates pathways created for GHGenius, a model used to analyze emissions from a variety of combustion sources. The study examined values reported in tests conducted by major oil and gas operators and described the conversion technologies typically used at FT distillates production facilities. Summaries of reports on FT distillates emissions were also provided. Three primary factors were identified that contributed to different results reported for FT distillates emissions: (1) the efficiency of the conversion process; (2) the allocation procedure used in the conventional oil refinery for the emissions of individual products; and (3) the emissions associated with natural gas production. The GHGenius model was used to quantify the impact of the 3 main factors. An alternative system expansion methodology was used to compare crude oil diesel pathways with a high efficiency, low gas leak scenario in order to achieve high values reported by some oil and gas operators. 5 refs., 5 tabs., 5 figs

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow

A Modeling Framework for Conventional and Heat Integrated Distillation Columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2013-01-01

In this paper, a generic, modular model framework for describing fluid separation by distillation is presented. At present, the framework is able to describe a conventional distillation column and a heat-integrated distillation column, but due to a modular structure the database can be further...

Renormalizing Entanglement Distillation

Science.gov (United States)

Waeldchen, Stephan; Gertis, Janina; Campbell, Earl T.; Eisert, Jens

2016-01-01

Entanglement distillation refers to the task of transforming a collection of weakly entangled pairs into fewer highly entangled ones. It is a core ingredient in quantum repeater protocols, which are needed to transmit entanglement over arbitrary distances in order to realize quantum key distribution schemes. Usually, it is assumed that the initial entangled pairs are identically and independently distributed and are uncorrelated with each other, an assumption that might not be reasonable at all in any entanglement generation process involving memory channels. Here, we introduce a framework that captures entanglement distillation in the presence of natural correlations arising from memory channels. Conceptually, we bring together ideas from condensed-matter physics—ideas from renormalization and matrix-product states and operators—with those of local entanglement manipulation, Markov chain mixing, and quantum error correction. We identify meaningful parameter regions for which we prove convergence to maximally entangled states, arising as the fixed points of a matrix-product operator renormalization flow.

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Garrow, J R

1921-04-16

To obtain an increased yield of by-products such as oils, ammonia, and gas from coal, oil shale, wood, peat, and the like by low and medium temperature processes, the requisite quantity of hot producer gas from a gas producer, is caused to travel, without ignition, through the material as it passes in a continuous manner through the retort so that the sensible heat of the producer gas is utilized to produce distillation of the carbonaceous material, the gases passing to a condenser, absorption apparatus, and an ammonia absorber respectively. In a two-stage method of treatment of materials such as peat or the like, separate supplies of producer gas are utilized for a preliminary drying operation and for the distillation of the material, the drying receptacle and the retort being joined together to render the process continuous. The gas from the drying receptacle may be mixed with the combined producer and retort gas from the retort, after the hydrocarbon oils have deen removed therefrom.

Aromatically enhanced pear distillates from blanquilla and conference varieties using a packed column.

Science.gov (United States)

Arrieta-Garay, Yanine; García-Llobodanin, Laura; Pérez-Correa, José Ricardo; López-Vázquez, Cristina; Orriols, Ignacio; López, Francisco

2013-05-22

Pear distillates are generally produced from the Bartlett variety because of its rich aroma. In this study, a chemical and sensorial comparative examination of pear distillates from the three main varieties grown in Spain (Bartlett, Blanquilla, and Conference) using two distillation systems (copper Charentais alembic and packed column) was undertaken. Volatile compounds were identified by gas chromatography to differentiate the spirits according to pear variety and distillation method. The Bartlett distillates from both distillation systems possessed higher ethyl ester and acetate and lower cis-3-hexen-1-ol and 1-hexanol concentrations. Despite these differences, a sensory analysis panel could distinguish only the Bartlett alembic distillate from the alembic distillates of the other varieties. In contrast, the panel rated the packed-column distillates equally. Therefore, less aromatic pear varieties can be used to produce distillates with aromatic characteristics similar to those of the Bartlett variety if a suitable distillation process is used.

Analytical determination of distillation boundaries for ternary azeotropic systems

OpenAIRE

Marcilla Gomis, Antonio; Reyes Labarta, Juan Antonio; Velasco, Raúl; Serrano Cayuelas, María Dolores; Olaya López, María del Mar

2009-01-01

A new straight forward algorithm to calculate distillation boundaries in ternary azeotropic systems has been developed. The proposed method allows, using cubic splines, the calculation of distillation trajectories and the calculation of that corresponding to the searched distillation boundaries. The algorithm is applied to 4 ternary liquid-vapour systems to test its validity. Vicepresidency of Research (University of Alicante) and Generalitat Valenciana (GV/2007/125)

Toxicity of petroleum hydrocarbon distillates to soil organisms.

Science.gov (United States)

Cermak, Janet H; Stephenson, Gladys L; Birkholz, Detlef; Wang, Zhendi; Dixon, D George

2010-12-01

Canadian standards for petroleum hydrocarbons in soil are based on four distillate ranges (F1, C6-C10; F2, >C10-C16; F3, >C16-C34; and F4, >C34). Concerns have arisen that the ecological soil contact standards for F3 may be overly conservative. Oil distillates were prepared and characterized, and the toxicity of F3 and two subfractions, F3a (>C16-C23) and F3b (>C23-C34), to earthworms (Eisenia andrei), springtails (Orthonychiurus folsomi), and northern wheatgrass (Elymus lanceolatus), as well as the toxicity of F2 to earthworms, was determined. Clean soil was spiked with individual distillates and measured concentrations were determined for select tests. Results agree with previous studies with these distillates. Reported toxicities of crude and petroleum products to invertebrates were generally comparable to that of F3 and F3a. The decreasing order of toxicity was F3a > F3 > F3b with invertebrates, and F3a > F3b > F3 with plants. The toxicities of F3a and F3b were not sufficiently different to recommend regulating hydrocarbons based on these distillate ranges. The results also suggest that test durations may be insufficient for determining toxicity of higher distillate ranges, and that the selection of species and endpoints may significantly affect interpretation of toxicity test results. Copyright © 2010 SETAC.

The composition-explicit distillation curve technique: Relating chemical analysis and physical properties of complex fluids.

Science.gov (United States)

Bruno, Thomas J; Ott, Lisa S; Lovestead, Tara M; Huber, Marcia L

2010-04-16

The analysis of complex fluids such as crude oils, fuels, vegetable oils and mixed waste streams poses significant challenges arising primarily from the multiplicity of components, the different properties of the components (polarity, polarizability, etc.) and matrix properties. We have recently introduced an analytical strategy that simplifies many of these analyses, and provides the added potential of linking compositional information with physical property information. This aspect can be used to facilitate equation of state development for the complex fluids. In addition to chemical characterization, the approach provides the ability to calculate thermodynamic properties for such complex heterogeneous streams. The technique is based on the advanced distillation curve (ADC) metrology, which separates a complex fluid by distillation into fractions that are sampled, and for which thermodynamically consistent temperatures are measured at atmospheric pressure. The collected sample fractions can be analyzed by any method that is appropriate. The analytical methods we have applied include gas chromatography (with flame ionization, mass spectrometric and sulfur chemiluminescence detection), thin layer chromatography, FTIR, corrosivity analysis, neutron activation analysis and cold neutron prompt gamma activation analysis. By far, the most widely used analytical technique we have used with the ADC is gas chromatography. This has enabled us to study finished fuels (gasoline, diesel fuels, aviation fuels, rocket propellants), crude oils (including a crude oil made from swine manure) and waste oils streams (used automotive and transformer oils). In this special issue of the Journal of Chromatography, specifically dedicated to extraction technologies, we describe the essential features of the advanced distillation curve metrology as an analytical strategy for complex fluids. Published by Elsevier B.V.

Graph Modelling Approach: Application to a Distillation Column

DEFF Research Database (Denmark)

Hovelaque, V.; Commault, C.; Bahar, Mehrdad

1997-01-01

Introduction, structured systems and digraphs, distillation column model, generic input-output decoupling problem, generic disturbance rejection problem, concluding remarks.......Introduction, structured systems and digraphs, distillation column model, generic input-output decoupling problem, generic disturbance rejection problem, concluding remarks....

Dry-distillation of experimental animal wastes containing radioisotopes

International Nuclear Information System (INIS)

Miyatake, Hideo; Saito, Kazumi; Kurihara, Norio

1988-01-01

Mice were dry-distilled at 800deg C for 10 min, after [ 32 P]orthophosphate or L-[4,5- 3 H]leucine was intraperitoneally administered. Phosphorus-32 was quantitatively recovered in the residual solid, whereas 95% of 3 H was found in the distillate (condensed water). When 14 C (L-[U- 14 C]malic acid or L-[U- 14 C]leucine) was administered to mice and they were dry-distilled, 14 C-radioactivity was distributed into two fractions; residual solid and exhaust gas. In these cases, the recovery percentage of 14 C in residual solid was not very high but increased as the treating temperature decreased. It reached about 40% of the administered 14 C at 400deg C for 120 min. By the dry-distillation of animals, their weight was reduced to about 10% in every animal tested (mice, rats and rabbits). The volume was reduced to about 20% in cases of mice and rats, and about 30% in case of rabbits. It was concluded that the dry-distillation can be useful as a pre-treatment for disposal of animal wastes containing radioisotopes. (author)

Structural Decoupling and Disturbance Rejection in a Distillation Column

DEFF Research Database (Denmark)

Bahar, Mehrdad; Jantzen, Jan; Commault, C.

1996-01-01

Introduction, distillation column model, input-output decoupling, disturbance rejection, concluding remarks, references.......Introduction, distillation column model, input-output decoupling, disturbance rejection, concluding remarks, references....

Apparatus for the distillation of coal, shale or other carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Wilson, P

1932-02-16

The design consists of a retort having a series of joined closed superheated sections each having a heavier gas delivery port therefrom leading to an outlet pipe in combination with a condenser, means above and on said sections comprising a series of hoppers in communication with a common feed hopper for carbonaceous materials to be distilled. An air tight cover for said feed hopper and intermediate rotatable valve control are provided. Means are provided for said carbonaceous material between said hoppers and said sections and adjacent means having lighter gas ports to a pipe also in communication with said condenser. A series of exit hoppers are located below such sections and means for feeding preheated gas through the exit hoppers to the material to be distilled are provided. A rotatable valve control means associated with the exit hoppers for discharging spent carbonaceous materials to separate water sealed outlets to a tank located below the apparatus.

Treatment of uranium-bearing wastewater by vacuum membrane distillation

International Nuclear Information System (INIS)

Duan Xiaolin; Li Qicheng; Chen Bingbing

2006-01-01

The removal of uranium from wastewater was carried out by vacuum membrane distillation (VMD) using microporous polypropylene membrane. The effects of feed temperature, mass concentration of U, flow rate and vacuum-side pressure on permeation flux and rejection were studied. The optimum experimental conditions are as follows: feed flow rate is 0.5 m/s, feed temperature is 55 degree C, vacuum-side pressure is 2.66 kPa. When the mass concentrations of U in the feed solution range from 1 mg/L to 9 mg/L, the membrane flux is 3.5 kg/(m 2 ·h) and the rejection rate is 99.1% under the optimum conditions. The water separated from uranium solution by vacuum membrane distillation could meet the state-controlled discharge standard 0.05 mg/L. The VMD as a novel technology will play an important role in the treatment of uranium-bearing wastewater. (authors)

Distilling solid carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1926-12-04

In the distillation of solid carbonaceous materials with by-product recovery by direct heating with a gas such as water gas, producer gas, or combustion gas which is passed in counter-flow to the materials, the volume of the gas used is such as to lower the vapor tension of the volatiles to enable the oil vapor to be liberated at temperatures not exceeding 450 to 500/sup 0/C and so that the gaseous mixture may be cooled to from 80 to 100/sup 0/C without causing the highest boiling oil fraction to condense. Coking coals may be subjected to a preliminary heat treatment with gases containing an oxygen content of from 2 to 8 percent to reduce their coking properties, and oxygen may be added to the heating gases to assist the polymerization of resinous bodies. Lubricating oil may be obtained by treating the primary oil with caustic soda to remove tar acids, refining the residue with sulfuric acid, distilling off 25 percent of the refined oil and passing the remainder through a filter press at -5/sup 0/C to extract the paraffin wax. The residue of wax-free oil is distilled to yield a lubricating oil which at normal temperatures has a static coefficient of friction of from .1 to .185. Other specifications are referred to.

Distillation of bituminous substances

Energy Technology Data Exchange (ETDEWEB)

du Buisson, M A.B.B.

1845-06-23

New and improved methods are described for the distillation of bituminous schistus and other bituminous substances, as well as for the purification, rectification, and preparation necessary for the employment of the productions obtained by such distillation for various useful purposes. This invention consists, first, in the arrangement and construction of furnace or apparatus for the distillation of schistus, and (any) other bituminous rocks. This furnace is made of circular brick-work, and is provided with the requisite number of fires placed round the circumference. The retort is of a conical or funnel shape, and when ready for use, has the appearance of one inverted cone being placed within a larger cone, in such a manner as to leave a space between the two cones for the reception of the schistus. Both cones are capable of being closed at their apexes, and their mouths, which are placed upwards, are connected together, and hermetically closed by a flat ring. The flame draft is caused to impinge against the lower portion of the outer cone and ascending, turns over the upper edge and descends within the inner cone to the mouth of the chimney, which is placed in the interior, and as low as may be convenient. A third cone is so placed within the inner cone as to cause the flame draft, in its descent, to bind against the surface of the retort.

27 CFR 24.290 - Removal of wine as distilling material.

Science.gov (United States)

2010-04-01

... or the distilled spirits plant. (b) Special natural wine. Unmarketable special natural wine may be removed to a distilled spirits plant for use as distilling material in the production of wine spirits (but... removal. If wine spirits produced from special natural wine contain any flavor characteristics of the...

Process and apparatus to analyze high-boiling products by distillation

Energy Technology Data Exchange (ETDEWEB)

Goupil, J.; Mouton, M.; Fischer, W.

1982-05-19

In the described process to analyze high-boiling petroleum products by distillation, contents of these products with atmospheric boiling points above 500/sup 0/C can be isolated as distillates. For this purpose the continuous shortway distillation process is employed and at least a part of the components of the apparatus which serve to introduce the raw product are heated seperately and held at different temperatures. The raw product is distributed on the combustion surface of the shortway distiller by a roller wiping system.

Input-Output Decoupling of a Distillation Column LV-Configuration

DEFF Research Database (Denmark)

Yazdi, H.; Jørgensen, Sten Bay; Bahar (fratrådt), Mehrdad

1996-01-01

Introduction, digraph approach, distillation column, digraph analysis, solution analysis, discussion and conclusion, references.......Introduction, digraph approach, distillation column, digraph analysis, solution analysis, discussion and conclusion, references....

27 CFR 28.301 - Loss of distilled spirits in transit.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Loss of distilled spirits in transit. 28.301 Section 28.301 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND....301 Loss of distilled spirits in transit. The tax on distilled spirits withdrawn without payment of...

Rhamnolipid produced by Pseudomonas aeruginosa USM-AR2 facilitates crude oil distillation.

Science.gov (United States)

Asshifa Md Noh, Nur; Al-Ashraf Abdullah, Amirul; Nasir Mohamad Ibrahim, Mohamad; Ramli Mohd Yahya, Ahmad

2012-01-01

A biosurfactant-producing and hydrocarbon-utilizing bacterium, Pseudomonas aeruginosa USM-AR2, was used to assist conventional distillation. Batch cultivation in a bioreactor gave a biomass of 9.4 g L(-1) and rhamnolipid concentration of 2.4 g L(-1) achieved after 72 h. Biosurfactant activity (rhamnolipid) was detected by the orcinol assay, emulsification index and drop collapse test. Pretreatment of crude oil TK-1 and AG-2 with a culture of P. aeruginosa USM-AR2 that contains rhamnolipid was proven to facilitate the distillation process by reducing the duration without reducing the quality of petroleum distillate. It showed a potential in reducing the duration of the distillation process, with at least 2- to 3-fold decreases in distillation time. This is supported by GC-MS analysis of the distillate where there was no difference between compounds detected in distillate obtained from treated or untreated crude oil. Calorimetric tests showed the calorie value of the distillate remained the same with or without treatment. These two factors confirmed that the quality of the distillate was not compromised and the incubation process by the microbial culture did not over-degrade the oil. The rhamnolipid produced by this culture was the main factor that enhanced the distillation performance, which is related to the emulsification of hydrocarbon chains in the crude oil. This biotreatment may play an important role to improve the existing conventional refinery and distillation process. Reducing the distillation times by pretreating the crude oil with a natural biosynthetic product translates to energy and cost savings in producing petroleum products.

Distillation irrigation: a low-energy process for coupling water purification and drip irrigation

Science.gov (United States)

Constantz, J.

1989-01-01

A method is proposed for combining solar distillation and drip irrigation to simultaneously desalinize water and apply this water to row crops. In this paper, the basic method is illustrated by a simple device constructed primarily of sheets of plastic, which uses solar energy to distill impaired water and apply the distillate to a widely spaced row crop. To predict the performance of the proposed device, an empirical equation for distillate production, dp, is developed from reported solar still production rates, and a modified Jensen-Haise equation is used to calculate the potential evapotranspiration, et, for a row crop. Monthly values for et and dp are calculated by using a generalized row crop at five locations in the Western United States. Calculated et values range from 1 to 22 cm month-1 and calculated dp values range from 2 to 11 cm month-1, depending on the location, the month, and the crop average. When the sum of dp plus precipitation, dp + P, is compared to et for the case of 50% distillation irrigation system coverage, the results indicate that the crop's et is matched by dp + P, at the cooler locations only. However, when the system coverage is increased to 66%, the crop's et is matched by dp + P even at the hottest location. Potential advantages of distillation irrigation include the ability: (a) to convert impaired water resources to water containing no salts or sediments; and (b) to efficiently and automatically irrigate crops at a rate that is controlled primarily by radiation intensities. The anticipated disadvantages of distillation irrigation include: (a) the high costs of a system, due to the large amounts of sheeting required, the short lifetime of the sheeting, and the physically cumbersome nature of a system; (b) the need for a widely spaced crop to reduce shading of the system by the crop; and (c) the production of a concentrated brine or precipitate, requiring proper off-site disposal. ?? 1989.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Mitting, E K

1882-08-09

The broken-up shale is placed in cast-iron retorts, heated externally, having exit tubes placed at a low level. Each retort is provided with a steam-pipe with a regulating-cock outside, the pipe being carried around the walls of the retort in a spiral or zig-zag way to ensure superheating of the steam, perforations being made in the pipe to allow exit for the steam into the retort. The steam, which may if desired be superheated before entrance, is passed into the retort when the latter has attained a temperature of from 210 to 250/sup 0/C and the passage is continued while the temperature rises, as long as distillation goes on. The exit pipe to the retort leads to a condenser of much condensing-surface, provided with a drag obtained by an exhausting steam jet or otherwise. The distilled products consist of tar, oils, wax, ammoniacal water (stated to be in greater proportion through the use of the process), and lighting and heating gas. The latter gas goes through a scrubber to a gasholder. The carbonaceous residue in the retort is discharged when cooled below a red heat, into sheet-iron cylinders, with tightly fitting lids, to avoid as far as possible contact with the atmosphere.

Method of distilling solid materials, such as shale

Energy Technology Data Exchange (ETDEWEB)

Ramen, A

1917-09-04

A method of distilling compact materials, such as shales, containing volatile matter, is characterized by heating the material in an oven or other apparatus or in a section or zone of same in the presence of some condensable gas (such as steam) which is indifferent to the vapors distillated during the heating of the material. The gas together with these products is conducted through a condensation apparatus, containing water or some other liquid, where the volatile matters are condensed. The steam which is produced in the gas regenerator is, after preheating, forced through the hot remaining residue from the distillation either in the same retort or in another retort in order to heat further this residue for the purpose of making it possible for the steam, by being forced through freshly charged material in the first oven or apparatus to bring about its distillation. The patent contains ten additional claims.

Advanced Control Synthesis for Reverse Osmosis Water Desalination Processes.

Science.gov (United States)

Phuc, Bui Duc Hong; You, Sam-Sang; Choi, Hyeung-Six; Jeong, Seok-Kwon

2017-11-01

  In this study, robust control synthesis has been applied to a reverse osmosis desalination plant whose product water flow and salinity are chosen as two controlled variables. The reverse osmosis process has been selected to study since it typically uses less energy than thermal distillation. The aim of the robust design is to overcome the limitation of classical controllers in dealing with large parametric uncertainties, external disturbances, sensor noises, and unmodeled process dynamics. The analyzed desalination process is modeled as a multi-input multi-output (MIMO) system with varying parameters. The control system is decoupled using a feed forward decoupling method to reduce the interactions between control channels. Both nominal and perturbed reverse osmosis systems have been analyzed using structured singular values for their stabilities and performances. Simulation results show that the system responses meet all the control requirements against various uncertainties. Finally the reduced order controller provides excellent robust performance, with achieving decoupling, disturbance attenuation, and noise rejection. It can help to reduce the membrane cleanings, increase the robustness against uncertainties, and lower the energy consumption for process monitoring.

Method of distillation of sulfurous bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Hallback, A J.S.; Bergh, S V

1918-04-22

A method of distillation of sulfur-containing bituminous shales is characterized by passing the hot sulfur-containing and oil-containing gases and vapors formed during the distillation through burned shale containing iron oxide, so that when these gases and vapors are thereafter cooled they will be, as far as possible, free from sulfur compounds. The patent contains six more claims.

Chemical profile of sugarcane spirits produced by double distillation methodologies in rectifying still

Directory of Open Access Journals (Sweden)

André Ricardo Alcarde

2011-06-01

Full Text Available The objective of this study was to determine the chemical profile of sugarcane spirits produced by different double distillation methodologies in rectifying still. Fermented sugarcane juice was distilled in rectifying still according to three double distillation methodologies: the methodology used for cognac production; the methodology used for whisky production; and the 10-80-10 percentage composition methodology, referring to the volumes of head, heart and tail of the distillate fractions from the second distillation. For comparison purposes, a simple distilled spirit was also produced. The distillates were analyzed for concentrations of ethanol, copper, volatile acidity, furfural and hydroxymethylfurfural, aldehydes, esters, methanol and higher alcohols. The spirits were also evaluated on the sensory attributes of aroma, taste and preference. Compared to simple distillation, double distillation improved the chemical quality of the spirits, since it has reduced the concentrations of acids, aldehydes, esters, methanol, higher alcohols and, consequently, their coefficient of congeners. Regardless of the methodology employed, the double distillation improved the sensory quality of the spirits since they obtained higher sensory acceptance in relation to spirits produced by simple distillation. Among double distilled spirits, the one produced according to whisky methodology obtained the best scores from appraisers on the aroma and flavor parameters and it was also the most preferred.

Solvent distillations studies for a reprocessing plant

International Nuclear Information System (INIS)

Ginisty, C.; Guillaume, B.

1989-01-01

The substantial amounts of solvent used in large reprocessing plants are such that considerable care must be paid to solvent management to limit the production of organic wastes. The installation of intensive treatment by chemical regeneration serves to increase the service life of the solvent. General solvent management, combined with a distillation unit under reduced pressure also helps to recycle the two components of the solvent at a low activity level. Distillation also serves to remove the heavy degradation products that are generally responsible for poor hydraulic behavior and for the holdup of radioactive products such as plutonium, zirconium and ruthenium. From the safety standpoint, the flashpoint of the distilled diluent tends to rise. It can therefore be recycled without risk

Vacuum distillation/vapor filtration water recovery

Science.gov (United States)

Honegger, R. J.; Neveril, R. B.; Remus, G. A.

1974-01-01

The development and evaluation of a vacuum distillation/vapor filtration (VD/VF) water recovery system are considered. As a functional model, the system converts urine and condensates waste water from six men to potable water on a steady-state basis. The system is designed for 180-day operating durations and for function on the ground, on zero-g aircraft, and in orbit. Preparatory tasks are summarized for conducting low gravity tests of a vacuum distillation/vapor filtration system for recovering water from urine.

The applicability of radiotracers for the investigation of the distillation of hydrocarbons

International Nuclear Information System (INIS)

Graczyk, J.; Iller, E.

1976-01-01

The use of radioactive tracers provide valuable methods for the investigation of distillation processes and have been applied to determine the characteristics of material streams, the dynamics of flowing phases and the composition in various parts of the distillation equipment. A method is proposed for testing individual radiotracers emplozemployed for the investigation of the distillation of hydrocarbons. The method consists in laboratory-scale distillation of a tracer together with a multicomponent hydrocarbon mixture, namely a gasoline fraction. The purification efficiency, distillation characteristics, and effective radiochemical purity of several tracers (reactor activated bromobenzene and synthesized C 3 H 7 82 Br, C 4 H 9 82 Br, C 5 H 11 82 Br) have been investigated. The distillation characteristics of bromohydrocarbons labelled with 82 Br and selected hydrocarbons tagged with 14 C (benzene and cumene) have been compared. The radiotracers investigated were employed for the determination of the hydrodynamic parameters of hydrocarbon distillation in laboratory packed columns and a commercial distillation tower. (author)

Modeling and analysis of conventional and heat-integrated distillation columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2015-01-01

A generic model that can cover diabatic and adiabatic distillation column configurations is presented, with the aim ofproviding a consistent basis for comparison of alternative distillation column technologies. Both a static and a dynamic formulation of the model, together with a model catalogue...... consisting of the conventional, the heat-integrated and the mechanical vapor recompression distillation columns are presented. The solution procedure of the model is outlined and illustrated in three case studies. One case study being a benchmark study demonstrating the size of the model and the static...... properties of two different heat-integrated distillation column (HIDiC) schemes and the mechanical vapor recompression column. The second case study exemplifies the difference between a HIDiC and a conventional distillation column in the composition profiles within a multicomponent separation, whereas...

Learning to Control Advanced Life Support Systems

Science.gov (United States)

Subramanian, Devika

2004-01-01

Advanced life support systems have many interacting processes and limited resources. Controlling and optimizing advanced life support systems presents unique challenges. In particular, advanced life support systems are nonlinear coupled dynamical systems and it is difficult for humans to take all interactions into account to design an effective control strategy. In this project. we developed several reinforcement learning controllers that actively explore the space of possible control strategies, guided by rewards from a user specified long term objective function. We evaluated these controllers using a discrete event simulation of an advanced life support system. This simulation, called BioSim, designed by Nasa scientists David Kortenkamp and Scott Bell has multiple, interacting life support modules including crew, food production, air revitalization, water recovery, solid waste incineration and power. They are implemented in a consumer/producer relationship in which certain modules produce resources that are consumed by other modules. Stores hold resources between modules. Control of this simulation is via adjusting flows of resources between modules and into/out of stores. We developed adaptive algorithms that control the flow of resources in BioSim. Our learning algorithms discovered several ingenious strategies for maximizing mission length by controlling the air and water recycling systems as well as crop planting schedules. By exploiting non-linearities in the overall system dynamics, the learned controllers easily out- performed controllers written by human experts. In sum, we accomplished three goals. We (1) developed foundations for learning models of coupled dynamical systems by active exploration of the state space, (2) developed and tested algorithms that learn to efficiently control air and water recycling processes as well as crop scheduling in Biosim, and (3) developed an understanding of the role machine learning in designing control systems for

27 CFR 19.65 - Experimental distilled spirits plants.

Science.gov (United States)

2010-04-01

... spirits plants. 19.65 Section 19.65 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Administrative and Miscellaneous Provisions Activities Not Subject to This Part § 19.65 Experimental distilled spirits plants. The...

Integrated Multiscale Latent Variable Regression and Application to Distillation Columns

Directory of Open Access Journals (Sweden)

Muddu Madakyaru

2013-01-01

Full Text Available Proper control of distillation columns requires estimating some key variables that are challenging to measure online (such as compositions, which are usually estimated using inferential models. Commonly used inferential models include latent variable regression (LVR techniques, such as principal component regression (PCR, partial least squares (PLS, and regularized canonical correlation analysis (RCCA. Unfortunately, measured practical data are usually contaminated with errors, which degrade the prediction abilities of inferential models. Therefore, noisy measurements need to be filtered to enhance the prediction accuracy of these models. Multiscale filtering has been shown to be a powerful feature extraction tool. In this work, the advantages of multiscale filtering are utilized to enhance the prediction accuracy of LVR models by developing an integrated multiscale LVR (IMSLVR modeling algorithm that integrates modeling and feature extraction. The idea behind the IMSLVR modeling algorithm is to filter the process data at different decomposition levels, model the filtered data from each level, and then select the LVR model that optimizes a model selection criterion. The performance of the developed IMSLVR algorithm is illustrated using three examples, one using synthetic data, one using simulated distillation column data, and one using experimental packed bed distillation column data. All examples clearly demonstrate the effectiveness of the IMSLVR algorithm over the conventional methods.

Improvement of Egyptian vacuum distillates by urea dewaxing

Directory of Open Access Journals (Sweden)

Ehssan M.R. Nassef

2015-09-01

Full Text Available The dewaxing of paraffinic lube stocks is an essential step in the production of lubricants to improve the operability of machines especially in winter. The present work deals with study of the urea dewaxing process of two types of Egyptian vacuum distillates. The effect of different compositions of methanol to water saturated with urea and yield of the oil, percent of wax, pour point, refractive index, viscosity, viscosity index and specific gravity of the oil produced from the two types of distillates (I and II were evaluated. The operating conditions of the urea adduct formation with n-paraffins using methanol to water mixture achieved the best pour point at −3.88 °C from an initial temperature of 4.4 °C for distillate I at (25/75 methanol to water. At the same ratio of methanol to water the best specific gravity of oil produced changed from 0.865 to 0.867, with viscosity index of 80. Percent yield of 50% for oil and percent wax of 50% were obtained. Results for distillate II, of higher specific gravity, are comparatively higher than those for distillate I. Experiments were carried out at room temperature.

Low temperature distillation of powdered materials

Energy Technology Data Exchange (ETDEWEB)

1929-04-11

In the low temperature distillation of powdered material such as coal, brown coal, or oil shale, dust carried by the gases and vapors is precipitated by supplying liquid hydrocarbons to the effluent gases, for example, to a dust remover through which the distillates pass. The material is supplied through a hopper and moved through a retort by a worm feed, and is discharged into a sump. Scavenging gases such as steam may be introduced through a pipe. Two conveyor worms moving in opposite directions are provided in an outlet conduit which may be surrounded by a cooling jacket. Heavy hydrocarbons condense on the walls of the conduit and on the conveyor worms and serve as dust catchers for the distillates, the lighted volatiles escaping through an outlet. The high boiling point oils flow back to and are cracked in the retort. Oils such as tar oils may be sprayed into the conduit or directly adjacent the entry of the material from feeding hopper.

Entanglement distillation protocols and number theory

International Nuclear Information System (INIS)

Bombin, H.; Martin-Delgado, M.A.

2005-01-01

We show that the analysis of entanglement distillation protocols for qudits of arbitrary dimension D benefits from applying basic concepts from number theory, since the set Z D n associated with Bell diagonal states is a module rather than a vector space. We find that a partition of Z D n into divisor classes characterizes the invariant properties of mixed Bell diagonal states under local permutations. We construct a very general class of recursion protocols by means of unitary operations implementing these local permutations. We study these distillation protocols depending on whether we use twirling operations in the intermediate steps or not, and we study them both analytically and numerically with Monte Carlo methods. In the absence of twirling operations, we construct extensions of the quantum privacy algorithms valid for secure communications with qudits of any dimension D. When D is a prime number, we show that distillation protocols are optimal both qualitatively and quantitatively

Advanced liquid metal reactor plant control system

International Nuclear Information System (INIS)

Dayal, Y.; Wagner, W.; Zizzo, D.; Carroll, D.

1993-01-01

The modular Advanced Liquid Metal Reactor (ALMR) power plant is controlled by an advanced state-of-the-art control system designed to facilitate plant operation, optimize availability, and protect plant investment. The control system features a high degree of automatic control and extensive amount of on-line diagnostics and operator aids. It can be built with today's control technology, and has the flexibility of adding new features that benefit plant operation and reduce O ampersand M costs as the technology matures

Simulation of ethanol extractive distillation with mixed glycols as separating agent

OpenAIRE

Gil, I. D.; García, L. C.; Rodríguez, G.

2014-01-01

Extractive distillation is an alternative for ethanol dehydration processes that has been shown to be more effective than azeotropic distillation and, in close proximity, to be very competitive against the process that uses adsorption with molecular sieves. Glycols have been shown to be the most effective solvents in extractive distillation, mainly ethylene glycol and glycerol. In this work, an extractive distillation column was simulated with the Aspen Plus software platform, using the RadFr...

Furnaces for the distillation of coal, etc

Energy Technology Data Exchange (ETDEWEB)

Anderson, F A; Deacon, M; Brady, N P.W.

1918-08-14

A tunnel or other furnace for the distillation of coal of the kind provided with inverted pockets in its roof to collect diverse distillates in the manner described, characterized by one or more of the pockets being provided with a sloping roof whose gradient from the higher end downwards is in the direction of the forward travel of the fuel beneath it for the purposes described.

Membrane distillation against a pressure difference

OpenAIRE

Keulen, L.; van der Ham, L.V.; Kuipers, N.J.M.; Hanemaaijer, J.H.; Vlugt, T.J.H.; Kjelstrup, S.

2017-01-01

Membrane distillation is an attractive technology for production of fresh water from seawater. The MemPower®MemPower® concept, studied in this work, uses available heat (86 °C) to produce pressurized water (2.2 bar and 46 °C) by membrane distillation, which again can be used to power a turbine for co-production of electricity. We develop a non-equilibrium thermodynamic model to accurately describe the transfer at the liquid-membrane interfaces, as well as through the hydrophobic membrane. The...

Distillation as a pretreatment process of waste scintillation solutions

International Nuclear Information System (INIS)

Dellamano, J.C.

1988-05-01

A process to pretreat scintillation solutions composed basically of PPO, POPOP, TOLUENE and ANTAROX, utilized by radioimmunoassay laboratories, is described. The technique employed is distillation which permits a waste reduction to about 40% of the initial volume with the recovery of the solvent (toluene). The recovered toluene can be resued for the same purpose, since it is free of radioactive material as assured by quality control procedures. (author) [pt

Chemical composition of distillers grains, a review.

Science.gov (United States)

Liu, KeShun

2011-03-09

In recent years, increasing demand for ethanol as a fuel additive and decreasing dependency on fossil fuels have resulted in a dramatic increase in the amount of grains used for ethanol production. Dry-grind is the major process, resulting in distillers dried grains with solubles (DDGS) as a major coproduct. Like fuel ethanol, DDGS has quickly become a global commodity. However, high compositional variation has been the main problem hindering its use as a feed ingredient. This review provides updated information on the chemical composition of distillers grains in terms of nutrient levels, changes during dry-grind processing, and causes for large variation. The occurrence in grain feedstock and the fate of mycotoxins during processing are also covered. During processing, starch is converted to glucose and then to ethanol and carbon dioxide. Most other components are relatively unchanged but concentrated in DDGS about 3-fold over the original feedstock. Mycotoxins, if present in the original feedstock, are also concentrated. Higher fold of increases in S, Na, and Ca are mostly due to exogenous addition during processing, whereas unusual changes in inorganic phosphorus (P) and phytate P indicate phytate hydrolysis by yeast phytase. Fermentation causes major changes, but other processing steps are also responsible. The causes for varying DDGS composition are multiple, including differences in feedstock species and composition, process methods and parameters, the amount of condensed solubles added to distiller wet grains, the effect of fermentation yeast, and analytical methodology. Most of them can be attributed to the complexity of the dry-grind process itself. It is hoped that information provided in this review will improve the understanding of the dry-grind process and aid in the development of strategies to control the compositional variation in DDGS.

Improving the Distillate Prediction of a Membrane Distillation Unit in a Trigeneration Scheme by Using Artificial Neural Networks

Directory of Open Access Journals (Sweden)

Luis Acevedo

2018-03-01

Full Text Available An Artificial Neural Network (ANN has been developed to predict the distillate produced in a permeate gap membrane distillation (PGMD module with process operating conditions (temperatures at the condenser and evaporator inlets, and feed seawater flow. Real data obtained from experimental tests were used for the ANN training and further validation and testing. This PGMD module constitutes part of an isolated trigeneration pilot unit fully supplied by solar and wind energy, which also provides power and sanitary hot water (SHW for a typical single family home. PGMD production was previously estimated with published data from the MD module manufacturer by means of a new type in the framework of Trnsys® simulation within the design of the complete trigeneration scheme. The performance of the ANN model was studied and improved through a parametric study varying the number of neurons in the hidden layer, the number of experimental datasets and by using different activation functions. The ANN obtained can be easily exported to be used in simulation, control or process analysis and optimization. Here, the ANN was finally used to implement a new type to estimate the PGMD production of the unit by using the inlet parameters obtained by the complete simulation model of the trigeneration unit based on Renewable Energy Sources (RES.

Distillation Parameters for Pilot Plant Production of Laurus nobilis Essential oil

Directory of Open Access Journals (Sweden)

Temel Özek

2012-01-01

Full Text Available Essential oils have increasing importance in flavour and fragrance industries. They are obtained by distillation techniques. In order to produce an oil with market potential its optimum production parameters have to be well known prior to its commercial production. Determination of the steam distillation parameters of commercially available Laurel leaves oil in pilot plant scale is described. The effect of steam rate and processing time play a major role in distillation of essential oils. Distillation speed was high in the beginning of the process, then gradually reduced as the distillation proceeded. The main component of the oil of Laurel leaf oil was 1,8-cineole accumulating significantly in the early fractions.

Distillation of solid carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Burney, C D

1918-08-31

A method of distilling carbonaceous material at low or moderate temperatures is described in which the main supply of gases for heating the material under treatment is generated in a combustion chamber located externally of the retort chamber from which combustion chamber the gases are withdrawn and passed under control through hollow elements located within the retort chamber in such manner as to insure the production of the desired temperature gradient along the length of the retort, the said elements being so constructed that they serve to bring the heating gases into indirect contact with the material undergoing treatment while also moving the material progressively through the retort in the opposite direction to that in which the heating gases flow.

Generalized Choi states and 2-distillability of quantum states

Science.gov (United States)

Chen, Lin; Tang, Wai-Shing; Yang, Yu

2018-05-01

We investigate the distillability of bipartite quantum states in terms of positive and completely positive maps. We construct the so-called generalized Choi states and show that it is distillable when it has negative partial transpose. We convert the distillability problem of 2-copy n× n Werner states into the determination of the positivity of an Hermitian matrix. We obtain several sufficient conditions by which the positivity holds. Further, we investigate the case n=3 by the classification of 2× 3× 3 pure states.

Advanced Controller for the Free-Piston Stirling Convertor

Science.gov (United States)

Gerber, Scott S.; Jamison, Mike; Roth, Mary Ellen; Regan, Timothy F.

2004-01-01

The free-piston Stirling power convertor is being considered as an advanced power conversion technology to be used for future NASA deep space missions requiring long life radioisotope power systems. This technology has a conversion efficiency of over 25%, which is significantly higher than the efficiency of the Radioisotope Thermal-electric Generators (RTG) now in use. The NASA Glenn Research Center has long been recognized as a leader in Stirling technology and is responsible for the development of advanced technologies that are intended to significantly improve key characteristics of the Stirling convertor. The advanced technologies identified for development also consider the requirements of potential future missions and the new capabilities that have become available in the associated technical areas. One of the key areas identified for technology development is the engine controller. To support this activity, an advanced controller is being developed for the Stirling power convertor. This controller utilizes active power factor correction electronics and microcontroller-based controls. The object of this paper is to present an overview of the advanced controller concept with modeling, simulation and hardware test data.

Method for controlling boiling point distribution of coal liquefaction oil product

Science.gov (United States)

Anderson, Raymond P.; Schmalzer, David K.; Wright, Charles H.

1982-12-21

The relative ratio of heavy distillate to light distillate produced in a coal liquefaction process is continuously controlled by automatically and continuously controlling the ratio of heavy distillate to light distillate in a liquid solvent used to form the feed slurry to the coal liquefaction zone, and varying the weight ratio of heavy distillate to light distillate in the liquid solvent inversely with respect to the desired weight ratio of heavy distillate to light distillate in the distillate fuel oil product. The concentration of light distillate and heavy distillate in the liquid solvent is controlled by recycling predetermined amounts of light distillate and heavy distillate for admixture with feed coal to the process in accordance with the foregoing relationships.

Distillation plant for tritium enrichment in metallic lithium

International Nuclear Information System (INIS)

Barnert, E.; Butzek, D.; Cordewiner, J.; Heinrichs, E.

1984-06-01

To close the external fuel cycle of fusion reactors, the tritium obtained from lithium must be separated off. One way of doing this is by high-temperature distillation and subsequent permeation. The construction of high-temperature distillation plant is described. For the time being, deuterium is processed instead of tritium. (orig.) [de

Construction and commissioning of a hydrogen cryogenic distillation system for tritium recovery at ICIT Rm. Valcea

Energy Technology Data Exchange (ETDEWEB)

Ana, George, E-mail: george.ana@icsi.ro [Institute for Cryogenic and Isotopic Technologies, Rm. Valcea (Romania); Cristescu, Ion [Karlsruhe Istitute for Technologies, Tritium Laboratory, Eggenstein-Leopoldshaffen (Germany); Draghia, Mirela [ISTECH, Timisoara (Romania); Bucur, Ciprian; Balteanu, Ovidiu; Vijulie, Mihai; Popescu, Gheorghe; Costeanu, Claudiu; Sofilca, Nicolae; Stefan, Iulia; Daramus, Robert; Niculescu, Alina; Oubraham, Anisoara; Spiridon, Ionut; Vasut, Felicia; Moraru, Carmen; Brad, Sebastian [Institute for Cryogenic and Isotopic Technologies, Rm. Valcea (Romania); Pasca, Gheorghe [ISTECH, Timisoara (Romania)

2016-05-15

Highlights: • Cryogenic distillation (CD) process is being employed for tritium separation from tritiated hydrogen mixtures. • Process control and safety phylosophy with the detritiation plant from Rm. Vâlcea. • Tests undertaken prior to commissioning of the CD system from Rm. Vâlcea. • Preliminary experiments with the CD system (non-radiological). - Abstract: Cryogenic distillation (CD) of hydrogen in combination with Liquid Phase Catalytic Exchange (LPCE) or Combined Electrolytic Catalytic Exchange (CECE) process is used for tritium removal/recovery from tritiated water. Tritiated water is being obtained after long time operation of CANDU reactors, or in case of ITER mainly by the Detritiation System (DS). The cryogenic distillation system (CDS) used to remove/recover tritium from a hydrogen stream consists of a cascade of cryogenic distillation columns and a refrigeration unit which provides the cooling capacity for the condensers of CD columns. The columns, together with the condensers and the process heat-exchangers are accommodated in a vacuumed cold box. In the particularly case of the ICIT Plant, the cryogenic distillation cascade consists of four columns with diameters between 100–7 mm and it has been designed to process up to 10 mc/h of tritiated deuterium. This paper will present the steps undertaken for construction and commissioning of a pilot plant for tritium removal/recovery by cryogenic distillation of hydrogen. The paper will show besides preliminary data obtained during commissioning, also general characteristics of the plant and its equipments.

Recovery of distillation, gasification, and if necessary redistilled products

Energy Technology Data Exchange (ETDEWEB)

Stier, H

1885-05-17

Collection chambers are operated in pairs. In one of a pair of chambers there is alternately gasification (heating gas generation or complete combustion), in the other distillation, and continually the products from combustion carry on the distillation.

Distilled water nasal provocation in hyperreactive patients.

Science.gov (United States)

Baudoin, T; Anzic, S A; Kalogjera, L

1999-01-01

Nonisotonic aerosol may act as a provocation agent in the upper and lower airways of hyperreactive individuals. The purpose of the study was to compare the results of nasal challenge with distilled water in patients with allergic rhinitis to those with noninfective nonallergic rhinitis (NINAR), with respect to the potential clinical use of the obtained data. A group of 68 ambulatory patients with allergic rhinitis or NINAR (39 perennial allergic, 6 seasonal, 23 NINAR) were challenged with 10 mL of distilled water aerosol after the baseline active anterior rhinomanometry. Patients with nasal polyposis at endoscopy, significant unilateral septal deviation, positive bacteriologic swab, recent nasal surgery, and uncertain anamnestic data about the medication taken 6 weeks before the provocation were excluded from the study. After 10 minutes of nasal provocation, rhinomanometry was repeated to assess the response. In 15 patients of the perennial allergic group, the same measurements were performed after a 2-week oral antihistamine and topical steroid therapy. Nasal resistance was significantly increased on the more patent side of the nose after nasal provocation with distilled water aerosol in allergic patients in comparison to the nasal resistance before provocation. In the patients with NINAR, the provocation resulted in a significant rise on the more patent side, but the total nasal airway resistance (NAR) levels were also significantly increased. The systemic antihistamine and topical steroid 2-week therapy in patients with perennial allergic rhinitis significantly reduced the response to nasal distilled water provocation. Nasal provocation with distilled water aerosol is a cheap, simple, and acceptable method that provides useful clinical data on the level of nonspecific nasal hyperreactivity and the therapy success.

Tritium isotope separation by water distillation column packed with silica-gel beads

International Nuclear Information System (INIS)

Fukada, Satoshi

2004-01-01

Tritium enrichment or depletion by water distillation was investigated using a glass column of 32cm in height packed with silica-gel beads of 3.4mm in average diameter. The total separation factor of the silica-gel distillation column, α H-T , was compared with those of an open column distillation tower and of a column packed with stainless-steel Dixon rings. Depletion of the tritium activity in the distillate was enhanced by isotopic exchange with water absorbed on silica-gel beads that have a higher affinity for HTO than for H 2 O. The value of α H-T -1 of the silica-gel distillation column was about four times larger than that of a column without any packing and about two times larger than that of the Dixon-ring column. The improvement of α H-T by the silica-gel adsorbent indicated that the height of the distillation-adsorption column becomes shorter than that of the height of conventional distillation columns. (author)

Recovery of acetic acid from waste streams by extractive distillation.

Science.gov (United States)

Demiral, H; Yildirim, M Ercengiz

2003-01-01

Wastes have been considered to be a serious worldwide environmental problem in recent years. Because of increasing pollution, these wastes should be treated. However, industrial wastes can contain a number of valuable organic components. Recovery of these components is important economically. Using conventional distillation techniques, the separation of acetic acid and water is both impractical and uneconomical, because it often requires large number of trays and a high reflux ratio. In practice special techniques are used depending on the concentration of acetic acid. Between 30 and 70% (w/w) acetic acid contents, extractive distillation was suggested. Extractive distillation is a multicomponent-rectification method similar in purpose to azeotropic distillation. In extractive distillation, to a binary mixture which is difficult or impossible to separate by ordinary means, a third component termed an entrainer is added which alters the relative volatility of the original constituents, thus permitting the separation. In our department acetic acid is used as a solvent during the obtaining of cobalt(III) acetate from cobalt(II) acetate by an electrochemical method. After the operation, the remaining waste contains acetic acid. In thiswork, acetic acid which has been found in this waste was recovered by extractive distillation. Adiponitrile and sulfolane were used as high boiling solvents and the effects of solvent feed rate/solution feed rate ratio and type were investigated. According to the experimental results, it was seem that the recovery of acetic acid from waste streams is possible by extractive distillation.

Preprototype vapor compression distillation subsystem. [recovering potable water from wastewater

Science.gov (United States)

Ellis, G. S.; Wynveen, R. A.; Schubert, F. H.

1979-01-01

A three-person capacity preprototype vapor compression distillation subsystem for recovering potable water from wastewater aboard spacecraft was designed, assembled, and tested. The major components of the subsystem are: (1) a distillation unit which includes a compressor, centrifuge, central shaft, and outer shell; (2) a purge pump; (3) a liquids pump; (4) a post-treat cartridge; (5) a recycle/filter tank; (6) an evaporator high liquid level sensor; and (7) the product water conductivity monitor. A computer based control monitor instrumentation carries out operating mode change sequences, monitors and displays subsystem parameters, maintains intramode controls, and stores and displays fault detection information. The mechanical hardware occupies 0.467 m3, requires 171 W of electrical power, and has a dry weight of 143 kg. The subsystem recovers potable water at a rate of 1.59 kg/hr, which is equivalent to a duty cycle of approximately 30% for a crew of three. The product water has no foul taste or odor. Continued development of the subsystem is recommended for reclaiming water for human consumption as well as for flash evaporator heat rejection, urinal flushing, washing, and other on-board water requirements.

Advanced Control of Wheeled Inverted Pendulum Systems

CERN Document Server

Li, Zhijun; Fan, Liping

2013-01-01

Advanced Control of Wheeled Inverted Pendulum Systems is an orderly presentation of recent ideas for overcoming the complications inherent in the control of wheeled inverted pendulum (WIP) systems, in the presence of uncertain dynamics, nonholonomic kinematic constraints as well as underactuated configurations. The text leads the reader in a theoretical exploration of problems in kinematics，dynamics modeling, advanced control design techniques,and trajectory generation for WIPs. An important concern is how to deal with various uncertainties associated with the nominal model, WIPs being characterized by unstable balance and unmodelled dynamics and being subject to time-varying external disturbances for which accurate models are hard to come by.   The book is self-contained, supplying the reader with everything from mathematical preliminaries and the basic Lagrange-Euler-based derivation of dynamics equations to various advanced motion control and force control approaches as well as trajectory generation met...

Determination of feasibility and advantages of using additional turbines to reduce energy consumption and CO2 emission of a distillation column

Directory of Open Access Journals (Sweden)

Svang-Ariyaskul Apichit

2014-01-01

Full Text Available Distillation is a process that consumes an extensive amount of energy and emits an enormous amount of CO2. It is attractive to reduce the energy consumption and CO2 emission for distillation. A new design of distillation is proposed by adding turbines in the vapor process streams before the condenser and after a reboiler to produce domestic electricity. As a result, this new design helps in reducing energy consumption and CO2 emission. The key variables are the distillate to feed ratio and the reflux ratio because they are the direct factors that control the vapor flowrates supplying the turbines. The distillation of an alkane mixture of C4 - C8 commonly found in a petroleum refinery was used as a test model to prove the process feasibility. The energy consumption and CO2 emission of the new process are reduced to 0.93 - 0.96 and 0.89 - 0.90 of the conventional process, respectively. This new design increases process efficiency in terms of second law efficiency by reducing the entropy generation from the conventional distillation at low distillate to feed ratios and reflux ratios. The distillation with additional turbines is promising to reduce energy consumption and CO2 emission and to increase process efficiency.

Hoizontal retort for distilling

Energy Technology Data Exchange (ETDEWEB)

Archer, F; Papineau, W

1854-12-15

Improvements are disclosed in distilling peaty, schistose, bituminous and vegetable matters. These are arranging a retort in a horizontal position or so little inclined as not to permit matters charged at one end of the retort to fall readily to the other by gravity. The retort is heated externally by a fire at one end, near which end the spent products are discharged without opening the retort, which is done by the aid of two valves or slides, one being at all times closed when discharging products. The other end of the retort is provided with a divided hopper with two valves or slides, one of which is kept closed when the other is open, in order to charge the retort. Within is an endless chain carrying rakes so as to move the matters from the feeding to the discharging end. There are outlets for the distilled products furnished with condensers.

Minimum number of transfer units and reboiler duty for multicomponent distillation columns

International Nuclear Information System (INIS)

Pleşu, Valentin; Bonet Ruiz, Alexandra Elena; Bonet, Jordi; Llorens, Joan; Iancu, Petrica

2013-01-01

Some guidelines to evaluate distillation columns, considering only basic thermodynamic data and principles, are provided in this paper. The method allows a first insight to the problem by simple calculations, without requiring column variables to ensure rational use of energy and low environmental impact. The separation system is approached by two complementary ways: minimum and infinite reflux flow rate. The minimum reflux provides the minimum energy requirements, and the infinite reflux provides the feasibility conditions. The difficulty of separation can be expressed in terms of number of transfer units (NTU). The applicability of the method is not mathematically limited by the number of components in the mixture. It is also applicable to reactive distillation. Several mixtures, including reactive distillation, are rigorously simulated as illustrative examples, to verify the applicability of the approach. The separation of the mixtures, performed by distillation columns, is feasible if a minimum NTU can be calculated between the distillate and bottom products. Once verified the feasibility of the separation, the maximum thermal efficiency depends only on boiling point of bottom and distillate streams. The minimum energy requirements corresponding to the reboiler can be calculated from the maximum thermal efficiency, and the variation of entropy and enthalpy of mixing between distillate and bottom streams. -- Highlights: • Feasibility analysis complemented with difficulty of separation parameters • Minimum and infinite reflux simplified models for distillation columns • Minimum number of transfer units (NTU) for packed columns at early design stages • Calculation of minimum energy distillation requirements at early design stages • Thermodynamic cycle approach and efficiency for distillation columns

Improved waste water vapor compression distillation technology. [for Spacelab

Science.gov (United States)

Johnson, K. L.; Nuccio, P. P.; Reveley, W. F.

1977-01-01

The vapor compression distillation process is a method of recovering potable water from crewman urine in a manned spacecraft or space station. A description is presented of the research and development approach to the solution of the various problems encountered with previous vapor compression distillation units. The design solutions considered are incorporated in the preliminary design of a vapor compression distillation subsystem. The new design concepts are available for integration in the next generation of support systems and, particularly, the regenerative life support evaluation intended for project Spacelab.

Vacuum distilling vessel

Energy Technology Data Exchange (ETDEWEB)

Reik, H

1928-12-27

Vacuum distilling vessel for mineral oil and the like, characterized by the ring-form or polyconal stiffeners arranged inside, suitably eccentric to the casing, being held at a distance from the casing by connecting members of such a height that in the resulting space if necessary can be arranged vapor-distributing pipes and a complete removal of the residue is possible.

Real time optimization of solar powered direct contact membrane distillation based on multivariable extremum seeking

KAUST Repository

Karam, Ayman M.; Laleg-Kirati, Taous-Meriem

2015-01-01

This paper presents a real time optimization scheme for a solar powered direct contact membrane distillation (DCMD) water desalination system. The sun and weather conditions vary and are inconsistent throughout the day. Therefore, the solar powered DCMD feed inlet temperature is never constant, which influences the distilled water flux. The problem of DCMD process optimization has not been studied enough. In this work, the response of the process under various feed inlet temperatures is investigated, which demonstrates the need for an optimal controller. To address this issue, we propose a multivariable Newton-based extremum seeking controller which optimizes the inlet feed and permeate mass flow rates as the feed inlet temperature varies. Results are presented and discussed for a realistic temperature profile.

Real time optimization of solar powered direct contact membrane distillation based on multivariable extremum seeking

KAUST Repository

Karam, Ayman M.

2015-09-21

This paper presents a real time optimization scheme for a solar powered direct contact membrane distillation (DCMD) water desalination system. The sun and weather conditions vary and are inconsistent throughout the day. Therefore, the solar powered DCMD feed inlet temperature is never constant, which influences the distilled water flux. The problem of DCMD process optimization has not been studied enough. In this work, the response of the process under various feed inlet temperatures is investigated, which demonstrates the need for an optimal controller. To address this issue, we propose a multivariable Newton-based extremum seeking controller which optimizes the inlet feed and permeate mass flow rates as the feed inlet temperature varies. Results are presented and discussed for a realistic temperature profile.

ITER task T48 (1994); low-inventory cryogenic distillation tests

Energy Technology Data Exchange (ETDEWEB)

Woodall, K; Robins, J; Bellamy, D [Ontario Hydro, Toronto, ON (Canada). Research Div.; Sood, S; Fong, C [Ontario Hydro, Toronto, ON (Canada)

1995-01-01

Previous work at Ontario Hydro Technologies (OHT) had shown that small cryogenic columns could be stably controlled and designed to much lower inventories than had been previously thought possible. Among the results were measurements of Height-of-Equivalent-Theoretical-Plate (HETP) versus holdup for Heli-Pak A and B in columns up to 20 mm diameter. ITER cryogenic distillation column designs suggest that the final high-tritium columns could be 30-70 mm diameter. The objective of this ITER task was to design and construct a column section for demonstration of scale-up of low inventory cryogenic distillation. The experiments were to be carried out in an upgraded Cryogenics Distillation Laboratory at OHT, in the facility used for previous low-inventory column tests. The ITER scaled-up test system as the following characteristics: 55 W condenser capacity; 30 mm diameter column loaded with Helipak B; 1500 mm packed height. The first task was to design and build the scaled-up test facility. In order to reduce costs, it was necessary to use existing 30-35 W helium refrigerators. Therefore, to provide 60-W duty to the scaled-up column, the two refrigerators had to be well coupled thermally, but not mechanically, since the refrigerator cold heads have very thin shells. The solution was to attach the column firmly to one cold head and indirectly to an adjacent cold head through flexible copper braid. Several iterations were required to obtain the desired good heat transfer with flexible mechanical connection. This facility is now operational and ready to begin measurements on the 30 mm column. Also during 1994, the Princeton Tritium Processing System (TPS) was installed and commissioned. The results from this experience are relevant to the ITER distillation system. 2 refs., 10 figs.

ITER task T48 (1994); low-inventory cryogenic distillation tests

International Nuclear Information System (INIS)

Woodall, K.; Robins, J.; Bellamy, D.

1995-01-01

Previous work at Ontario Hydro Technologies (OHT) had shown that small cryogenic columns could be stably controlled and designed to much lower inventories than had been previously thought possible. Among the results were measurements of Height-of-Equivalent-Theoretical-Plate (HETP) versus holdup for Heli-Pak A and B in columns up to 20 mm diameter. ITER cryogenic distillation column designs suggest that the final high-tritium columns could be 30-70 mm diameter. The objective of this ITER task was to design and construct a column section for demonstration of scale-up of low inventory cryogenic distillation. The experiments were to be carried out in an upgraded Cryogenics Distillation Laboratory at OHT, in the facility used for previous low-inventory column tests. The ITER scaled-up test system as the following characteristics: 55 W condenser capacity; 30 mm diameter column loaded with Helipak B; 1500 mm packed height. The first task was to design and build the scaled-up test facility. In order to reduce costs, it was necessary to use existing 30-35 W helium refrigerators. Therefore, to provide 60-W duty to the scaled-up column, the two refrigerators had to be well coupled thermally, but not mechanically, since the refrigerator cold heads have very thin shells. The solution was to attach the column firmly to one cold head and indirectly to an adjacent cold head through flexible copper braid. Several iterations were required to obtain the desired good heat transfer with flexible mechanical connection. This facility is now operational and ready to begin measurements on the 30 mm column. Also during 1994, the Princeton Tritium Processing System (TPS) was installed and commissioned. The results from this experience are relevant to the ITER distillation system. 2 refs., 10 figs

An improvement study on the closed chamber distillation system for recovery of renewable salts from salt wastes containing radioactive rare earth compounds

International Nuclear Information System (INIS)

Eun, H.C.; Cho, Y.Z.; Lee, T.K.; Kim, I.T.; Park, G.I.; Lee, H.S.

2013-01-01

In this paper, an improvement study on the closed chamber distillation system for recovery of renewable salts from salt wastes containing radioactive rare earth compounds was performed to determine optimum operating conditions. It was very important to maintain the pressure in the distillation chamber below 10 Torr for a high efficiency (salt recovery >99 %) of the salt distillation. This required increasing the salt vaporization and condensation rates in the distillation system. It was confirmed that vaporization and condensation rates could be improved controlling the given temperature of top of the condensation chamber. In the distillation tests of the salt wastes containing rare earth compounds, the operation time at a given temperature was greatly reduced changing the given temperature of top of the condensation chamber from 780 to 700 deg C. (author)

Validating the Equilibrium Stage Model for an Azeotropic System in a Laboratorial Distillation Column

Science.gov (United States)

Duarte, B. P. M.; Coelho Pinheiro, M. N.; Silva, D. C. M.; Moura, M. J.

2006-01-01

The experiment described is an excellent opportunity to apply theoretical concepts of distillation, thermodynamics of mixtures and process simulation at laboratory scale, and simultaneously enhance the ability of students to operate, control and monitor complex units.

27 CFR 26.230 - Containers of distilled spirits to bear closures.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Containers of distilled spirits to bear closures. 26.230 Section 26.230 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO... distilled spirits to bear closures. Containers of 1 gallon (3.785 liters) or less of distilled spirits, upon...

Dynamic simulation of hydrogen isotope distillation unit

International Nuclear Information System (INIS)

Le Lann, J.M.; Latge, C.; Joulia, X.; Sere-Peyrigain, P.

1995-01-01

Dynamic simulation of hydrogen isotope distillation unit involved in the complex environment of a fusion power plant can be a powerful technique in view to analyze the tritium hazard potential. In this paper, issues related to the development of such a dynamic simulator with model formulation and the numerical treatment of the resulting Differential-Algebraic equation (DAE) system are properly adressed. The typical dynamic characteristics of such columns are quantitatively and qualitatively enlighted on case study with very large disturbances. The developed system has proven to be beneficial for understanding the dynamic behaviour and further for developing control schemes. (orig.)

Dynamic simulation of hydrogen isotope distillation unit

International Nuclear Information System (INIS)

Le Lann, J.M.; Joulia, X.; Sere-Peyrigain, P.

1994-01-01

Dynamic simulation of hydrogen isotope distillation unit involved in the complex environment of a fusion power plant can be a powerful technique in view to analyze the tritium hazard potential. Issues related to the development of such a dynamic simulator with model formulation and the numerical treatment of the resulting Differential-Algebraic equation (DAE) system are properly addressed. The typical dynamic characteristics of such columns are quantitatively and qualitatively enlightened on case study with very large disturbances. The developed system has proven to be beneficial for understanding the dynamic behaviour and further for developing control schemes. (author) 12 refs.; 4 figs

Economical investigation of solar water distillation in Egypt

Energy Technology Data Exchange (ETDEWEB)

Sakr, I A; Khalil, M A; Delyannis, A; Delyannis, E [eds.

1976-01-01

Many ways of solar water distillation have been suggested but most of them are either too expensive or only a practical solution to different processes under investigation. Solar heat distillation has a bright future because the greatest potential needs appear to be in those sections where the availability of solar energy is high and the availability of potable water is low as in our Egyptian deserts where the solar intensity has a yearly mean value of about 6000 kcal/(m/sup 2/day). The solar distillation method has a number of economic characteristics which are different from other sea water conversion methods, including: The processing equipment is very simple and results in low equipment costs. No special skills are required for both erection and operation. It can be used with saline water of wide range of salt concentration. The still design is essentially modular, and can be made to meet any desired capacity. Scale formation and corrosion are minor problems as compared with other methods. Power requirements are negligible. The cost of unit construction is not markedly influenced by the size of the still. The lack of quantitative and operative data of solar water distillation techniques with respect to their cost needs in investigation from the economical standpoint of view in Egypt. The subject of this work is to find the order of magnitude of the fresh water cost by solar distillation.

Sealing ability of mineral trioxide aggregate (MTA) combined with distilled water, chlorhexidine, and doxycycline.

Science.gov (United States)

Arruda, Roberta A A; Cunha, Rodrigo S; Miguita, Kenner B; Silveira, Cláudia F M; De Martin, Alexandre S; Pinheiro, Sérgio L; Rocha, Daniel G P; Bueno, Carlos E S

2012-09-01

The aim of this study was to evaluate the sealing ability of mineral trioxide aggregate (MTA Bio) combined with different mixing agents (distilled water, chlorhexidine, doxycycline), used as an apical root-end filling material. Forty-two extracted human teeth were divided into three groups (n = 12); six teeth were used as controls. Root-ends were resected at 90 degrees, 3 mm from the apex. Root-end cavities were prepared using ultrasonic tips and filled with MTA Bio plus distilled water, 2% chlorhexidine solution, or 10% doxycycline solution. Apical sealing was assessed by microleakage of 50% silver nitrate solution. Roots were longitudinally sectioned in a buccolingual plane and analyzed using an operating microscope (20× magnification). Depth of dye leakage into the dentinal walls was measured in millimeters. Results were analyzed using ANOVA and Tukey's test (P = 0.05). MTA Bio plus distilled water showed significantly higher mean leakage results (1.06 mm) when compared with MTA Bio plus doxycycline (0.61 mm), and higher, although not significant, results when compared with MTA Bio plus chlorhexidine (0.79 mm). In conclusion, replacing distilled water with two biologically active mixing agents (doxycycline and chlorhexidine) did not alter the sealing properties of MTABio. The antimicrobial properties of these combinations should be further investigated.

Design and control of an ideal heat-integrated distillation column (ideal HIDiC) system separating a close-boiling ternary mixture

International Nuclear Information System (INIS)

Huang Kejin; Shan Lan; Zhu Qunxiong; Qian Jixin

2007-01-01

Despite the fact that a stand-alone ideal heat-integrated distillation column (ideal HIDiC) can be thermodynamically efficient and operationally stable, the application of an ideal HIDiC system to separate a close-boiling multi-component mixture is still a challenging problem because of the possibility of strong interactions within/between the ideal HIDiCs involved. In this work, employment of two ideal HIDiCs to separate a close-boiling ternary mixture is studied in terms of static and dynamic performance. It is found that the ideal HIDiC system can be a competitive alternative with a substantial energy saving and comparable dynamic performance in comparison with its conventional counterpart. The direct sequence appears to be superior to the indirect sequence due to the relatively small vapor flow rates to the compressors. Controlling the bottom composition of the first ideal HIDiC with the pressure elevation from the stripping section to the rectifying section helps to suppress the disturbances from the feed to the second ideal HIDiC. Special caution should, however, be taken when the latent heat of the distillates is to be recovered within/between the ideal HIDiCs involved, because a positive feedback mechanism may be formed and give rise to additional difficulties in process operation

Control of Refining Processes on Mid-Distillates by Near Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Zanier-Szydlowski N.

1999-07-01

Full Text Available The purpose of this paper is to demonstrate the accuracy of physicochemical determinations based on equations calculated by multivariate analysis of near infrared spectra which gives access to simultaneous analyses both on-line and off-line. Detailed results concerning the determination of the refractive index at 20°C, the density, the weight% of hydrogen, the % of aromatic carbon, the weight% of mono-, di- and total aromatics and the cetane number on mid-distillates are given in a shorter time than using the conventional approach by standardized methods. It is shown that near infrared spectroscopy combined with chemometrics should allow detailed and precise comparisons of the hydrotreatment process efficiencies.

Retorts; distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Kirk, A C

1869-11-09

Relates to retorts for distilling shale or other purposes. Each retort has a mouthpiece, which projects into a water trough, having a curved bottom, and sides rising up to ridges, from which extend shoots. Attached to links is the reciprocating discharge bar, actuated from a steam engine, etc., which, through worm-wheel gearing and a shaft, imparts an intermittent motion to a pawl which propels a ratchet-wheel, which is prevented from turning backward by a catch, and drives a rotary shaft, the motion being transmitted to a bar through a crank and rod. The bar, in rising, pushes the residue from the retort out of the trough, over the ridges, and down the shoots into the truck, etc. The vertical retort is made in two lengths, at the joint between which is held the flange of the shell, joined to, or cast with, the part of the retort and forming a jacket into which steam or other vapor or gas is introduced by a pipe. The steam, etc., circulates through an external spiral rib of the shell and issues from the bottom of the shale among the shale, etc., being distilled.

Desalination and water recycling by air gap membrane distillation

NARCIS (Netherlands)

Meindersma, G.W.; Guijt, C.M.; Haan, de A.B.

2006-01-01

Membrane distillation (MD) is an emerging technology for desalination. Membrane distillation differs from other membrane technologies in that the driving force for desalination is the difference in vapour pressure of water across the membrane, rather than total pressure. The membranes for MD are

Desalination and Water Recycling by Air Gap Membrane Distillation

NARCIS (Netherlands)

Meindersma, G.W.; Guijt, C.M.; de Haan, A.B.

2006-01-01

Membrane distillation (MD) is an emerging technology for desalination. Membrane distillation differs from other membrane technologies in that the driving force for desalination is the difference in vapour pressure of water across the membrane, rather than total pressure. The membranes for MD are

Multipartite secret key distillation and bound entanglement

International Nuclear Information System (INIS)

Augusiak, Remigiusz; Horodecki, Pawel

2009-01-01

Recently it has been shown that quantum cryptography beyond pure entanglement distillation is possible and a paradigm for the associated protocols has been established. Here we systematically generalize the whole paradigm to the multipartite scenario. We provide constructions of new classes of multipartite bound entangled states, i.e., those with underlying twisted Greenberger-Horne-Zeilinger (GHZ) structure and nonzero distillable cryptographic key. We quantitatively estimate the key from below with the help of the privacy squeezing technique.

27 CFR 28.40 - Evidence of exportation: distilled spirits and wine.

Science.gov (United States)

2010-04-01

...: distilled spirits and wine. 28.40 Section 28.40 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO... Provisions Evidence of Exportation and Use § 28.40 Evidence of exportation: distilled spirits and wine. The exportation of any shipment of distilled spirits or wine may be evidenced by: (a) A copy of the export bill of...

Superadditivity of distillable entanglement from quantum teleportation

Science.gov (United States)

Bandyopadhyay, Somshubhro; Roychowdhury, Vwani

2005-12-01

We show that the phenomenon of superadditivity of distillable entanglement observed in multipartite quantum systems results from the consideration of states created during the execution of the standard end-to-end quantum teleportation protocol [and a few additional local operations and classical communication (LOCC) steps] on a linear chain of singlets. Some of these intermediate states are tensor products of bound entangled (BE) states, and hence, by construction possess distillable entanglement, which can be unlocked by simply completing the rest of the LOCC operations required by the underlying teleportation protocol. We use this systematic approach to construct both new and known examples of superactivation of bound entanglement, and examples of activation of BE states using other BE states. A surprising outcome is the construction of noiseless quantum relay channels with no distillable entanglement between any two parties, except for that between the two end nodes.

Superadditivity of distillable entanglement from quantum teleportation

International Nuclear Information System (INIS)

Bandyopadhyay, Somshubhro; Roychowdhury, Vwani

2005-01-01

We show that the phenomenon of superadditivity of distillable entanglement observed in multipartite quantum systems results from the consideration of states created during the execution of the standard end-to-end quantum teleportation protocol [and a few additional local operations and classical communication (LOCC) steps] on a linear chain of singlets. Some of these intermediate states are tensor products of bound entangled (BE) states, and hence, by construction possess distillable entanglement, which can be unlocked by simply completing the rest of the LOCC operations required by the underlying teleportation protocol. We use this systematic approach to construct both new and known examples of superactivation of bound entanglement, and examples of activation of BE states using other BE states. A surprising outcome is the construction of noiseless quantum relay channels with no distillable entanglement between any two parties, except for that between the two end nodes

Aroma Stripping under various Forms of Membrane Distillation Processes: Experiments and modeling

DEFF Research Database (Denmark)

Jonsson, Gunnar Eigil

Concentration of fruit juices by membrane distillation is an interesting process as it can be done at low temperature giving a gentle concentration process with little deterioration of the juices. Since the juices contains many different aroma compounds with a wide range of chemical properties...... such as volatility, activity coefficient and vapor pressure, it is important to know how these aroma compounds will eventually pass through the membrane. Experiments have been made on an aroma model solution and on black currant juice in a lab scale membrane distillation set up which can be operated in various types...... of MD configurations: Vacuum Membrane Distillation , Sweeping Gas Membrane Distillation , Direct Contact Membrane Distillation and Osmotic Membrane Distillation. The influence of feed temperature and feed flow rate on the permeate flux and concentration factor for different types of aroma compounds have...

Effects of season and inclusion of corn distillers dried grains with solubles in creep feed on intake, microbial protein synthesis and efficiency, ruminal fermentation, digestion, and performance of nursing calves grazing native range in southeastern North Dakota.

Science.gov (United States)

Reed, J J; Lardy, G P; Bauer, M L; Gibson, M; Caton, J S

2006-08-01

Nine ruminally and duodenally cannulated (145 +/- 21 kg of initial BW; Exp. 1) and sixteen intact (181 +/- 36 kg of initial BW; Exp. 2), commercial, Angus, nursing, steer calves were used to evaluate the effects of advancing season and corn distillers dried grains with solubles in creep feed on intake, digestion, microbial efficiency, ruminal fermentation, and performance while grazing native rangeland. Calves were assigned to 1 of 2 treatments: a supplement containing 41% soybean meal, 26.25% wheat middlings, 26.25% soybean hulls, 5% molasses, and 1.5% limestone (control) or a supplement containing 50% corn distillers dried grains with solubles, 14.25% wheat middlings, 14.25% soybean hulls, 14% soybean meal, 5% molasses, and 1.5% limestone (CDDGS). Calves were offered supplement individually (0.45% of BW) once daily. Three 15-d collection periods occurred in June, July, and August. In Exp. 1, there were no differences in OM intake, or OM, N, NDF, or ADF digestion between control calves and those fed CDDGS. Forage and total OM intake increased (P Calves consuming CDDGS had decreased (P intake (% of BW) was less for CDDGS compared with control calves, but there were no differences in performance or subsequent carcass composition between treatments. Inclusion of 50% corn distillers dried grains with solubles in a creep supplement for nursing calves produced similar results compared with a control creep feed based on soybean meal, soybean hulls, and wheat middlings.

Qutrit magic state distillation

International Nuclear Information System (INIS)

Anwar, Hussain; Browne, Dan E; Campbell, Earl T

2012-01-01

Magic state distillation (MSD) is a purification protocol that plays an important role in fault-tolerant quantum computation. Repeated iteration of the steps of an MSD protocol generates pure single non-stabilizer states, or magic states, from multiple copies of a mixed resource state using stabilizer operations only. Thus mixed resource states promote the stabilizer operations to full universality. MSD was introduced for qubit-based quantum computation, but little has been known concerning MSD in higher-dimensional qudit-based computation. Here, we describe a general approach for studying MSD in higher dimensions. We use it to investigate the features of a qutrit MSD protocol based on the five-qutrit stabilizer code. We show that this protocol distils non-stabilizer magic states, and identify two types of states that are attractors of this iteration map. Finally, we show how these states may be converted, via stabilizer circuits alone, into a state suitable for state-injected implementation of a non-Clifford phase gate, enabling non-Clifford unitary computation. (paper)

Distillability Sudden Birth of Entanglement for Qutrit-Qutrit Systems

International Nuclear Information System (INIS)

Huang Jiang; Ali Mazhar

2014-01-01

We report the sudden appearance of distillability between two statistically independent reservoirs modelled as qutrit-qutrit systems. This feature of bipartite quantum systems is different from the previously observed phenomenon of entanglement sudden birth. It is found that the states of reservoirs first become bound entangled, thus exhibiting entanglement sudden birth, consequently followed by the sudden birth of distillability, and it is shown that whenever distillability is lost abruptly from principal system, it also necessarily appears abruptly among reservoirs' degrees of freedom. This surprising observation reflects yet another peculiarity of dynamical aspects of quantum entanglement

Irreversibility of entanglement distillation for a class of symmetric states

International Nuclear Information System (INIS)

Vollbrecht, Karl Gerd H.; Wolf, Michael M.; Werner, Reinhard F.

2004-01-01

We investigate the irreversibility of entanglement distillation for a symmetric (d+1)-parameter family of mixed bipartite quantum states acting on Hilbert spaces of arbitrary dimension dxd. We prove that in this family the entanglement cost is generically strictly larger than the distillable entanglement, so that the set of states for which the distillation process is asymptotically reversible is of measure zero. This remains true even if the distillation process is catalytically assisted by pure-state entanglement and every operation is allowed, which preserves the positivity of the partial transpose. It is shown that reversibility occurs only in cases where the state is a tagged mixture. The reversible cases are shown to be completely characterized by minimal uncertainty vectors for entropic uncertainty relations

Anaesthetic effects of Adenia gummifera distillates on Apis mellifera (Honeybee).

Science.gov (United States)

Ngarivhume, T; Dzomba, P; Gwizangwe, I; Zendera, C H; Katsvanga, C A T; Jimu, L; Moyo, M; Chagonda, T

2008-01-01

The anaesthetic activities of steam distillates of Adenia gummifera stem on Apis mellifera were evaluated by a diffusion method. Live, direct and fractional (61-80 degrees C fraction) distillates had greater anaesthetic effect while vacuum distillates were mild. The anaesthetic activity significantly increased with concentration up to 6% (v/v), and then it levelled off, while excessive exposure was lethal. The number of bees in a given volume had no significant effect on anaesthetic activity but container volume (F(cal) = 66.4; F(3,8) = 4.07) and bee-distillate distance (F(cal) = 31.0; F(2,6) = 5.14) did, suggesting the rate of diffusion of active component could be the determining factor. The active component is likely to contain amines and the rest halogenated alkane.

Improvement of Batch Distillation Separation of Azeotropic Mixtures

OpenAIRE

Hegely, Laszlo

2013-01-01

La distillation est le procédé de séparation le plus répandu dans l'industrie chimique. Pour la séparation des mélanges azéotropiques, une méthode spéciale de distillation doit être appliquée. Le but de mon travail était d'améliorer la séparation des mélanges azéotropiques par distillation discontinue (DD). Un nouvel algorithme a été présenté pour la détermination de la séquence des produits de DD pour des mélanges multicomposants azéotropiques. Contrairement aux méthodes publiées précédemmen...

Complete nutrient recovery from source-separated urine by nitrification and distillation.

Science.gov (United States)

Udert, K M; Wächter, M

2012-02-01

In this study we present a method to recover all nutrients from source-separated urine in a dry solid by combining biological nitrification with distillation. In a first process step, a membrane-aerated biofilm reactor was operated stably for more than 12 months, producing a nutrient solution with a pH between 6.2 and 7.0 (depending on the pH set-point), and an ammonium to nitrate ratio between 0.87 and 1.15 gN gN(-1). The maximum nitrification rate was 1.8 ± 0.3 gN m(-2) d(-1). Process stability was achieved by controlling the pH via the influent. In the second process step, real nitrified urine and synthetic solutions were concentrated in lab-scale distillation reactors. All nutrients were recovered in a dry powder except for some ammonia (less than 3% of total nitrogen). We estimate that the primary energy demand for a simple nitrification/distillation process is four to five times higher than removing nitrogen and phosphorus in a conventional wastewater treatment plant and producing the equivalent amount of phosphorus and nitrogen fertilizers. However, the primary energy demand can be reduced to values very close to conventional treatment, if 80% of the water is removed with reverse osmosis and distillation is operated with vapor compression. The ammonium nitrate content of the solid residue is below the limit at which stringent EU safety regulations for fertilizers come into effect; nevertheless, we propose some additional process steps that will increase the thermal stability of the solid product. Copyright © 2011 Elsevier Ltd. All rights reserved.

Key distillation in quantum cryptography

Science.gov (United States)

Slutsky, Boris Aron

1998-11-01

Quantum cryptography is a technique which permits two parties to communicate over an open channel and establish a shared sequence of bits known only to themselves. This task, provably impossible in classical cryptography, is accomplished by encoding the data on quantum particles and harnessing their unique properties. It is believed that no eavesdropping attack consistent with the laws of quantum theory can compromise the secret data unknowingly to the legitimate users of the channel. Any attempt by a hostile actor to monitor the data carrying particles while in transit reveals itself through transmission errors it must inevitably introduce. Unfortunately, in practice a communication is not free of errors even when no eavesdropping is present. Key distillation is a technique that permits the parties to overcome this difficulty and establish a secret key despite channel defects, under the assumption that every particle is handled independently from other particles by the enemy. In the present work, key distillation is described and its various aspects are studied. A relationship is derived between the average error rate resulting from an eavesdropping attack and the amount of information obtained by the attacker. Formal definition is developed of the security of the final key. The net throughput of secret bits in a quantum cryptosystem employing key distillation is assessed. An overview of quantum cryptographic protocols and related information theoretical results is also given.

The evaporation of oil spills: prediction of equations using distillation data

International Nuclear Information System (INIS)

Fingas, M.

1997-01-01

The evaporative characteristics of 19 different crude oils and petroleum products were studied . Best-fit equation parameters were determined for percentage loss by time and absolute weight loss. Except in three cases, all oils were found to fit logarithmic curves. The equation constants were correlated with oil distillation data. Relationships enabling calculation of evaporation equations directly from distillation data have been developed. The high correlation of distillation data and evaporation data suggests that the two processes are analogous and that evaporation, like distillation, is largely governed by intrinsic oil properties rather than environmental properties such as boundary-layer factors

Towards energy efficient distillation technologies - Making the right choice

NARCIS (Netherlands)

Kiss, A.A.; Landaeta, S.J. Flores; Ferreira, C.A.I.

2012-01-01

In spite of claiming around half of the operational costs of chemical plants, distillation is still the most popular separation technology. Distillation has low thermodynamic efficiency, requiring the input of high quality energy in the reboiler – while rejecting a similar amount of heat at lower

Molten salt extractive distillation process for zirconium-hafnium separation

International Nuclear Information System (INIS)

McLaughlin, D.F.; Stoltz, R.A.

1989-01-01

This patent describes an improvement in a process for zirconium-hafnium separation. It utilizes an extractive distillation column with a mixture of zirconium and hafnium tetrachlorides introduced into a distillation column having a top and bottom with hafnium enriched overheads taken from the top of the column and a molten salt solvent circulated through the column to provide a liquid phase, and with molten salt solvent containing zirconium chloride being taken from the bottom of the distillation column. The improvements comprising: utilizing a molten salt solvent consisting principally of lithium chloride and at least one of sodium, potassium, magnesium and calcium chlorides; stripping of the zirconium chloride taken from the bottom of the distillation column by electrochemically reducing zirconium from the molten salt solvent; and utilizing a pressurized reflux condenser on the top of the column to add the hafnium chloride enriched overheads to the molten salt solvent previously stripped of zirconium chloride

Distilling hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Bataafsche, N V; de Brey, J H.C.

1918-10-30

Hydrocarbons containing a very volatile constituent and less volatile constituents, such as casing-head gases, still gases from the distillation of crude petroleum and bituminous shale are separated into their constituents by rectification under pressure; a pressure of 20 atmospheres and limiting temperatures of 150/sup 0/C and 40/sup 0/C are mentioned as suitable. The mixture may be subjected to a preliminary treatment consisting in heating to a temperature below the maximum rectification temperature at a pressure greater than that proposed to be used in the rectification.

Introduction to Advanced Engine Control Concepts

Science.gov (United States)

Sanjay, Garg

2007-01-01

With the increased emphasis on aircraft safety, enhanced performance and affordability, and the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Branch at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC) in Cleveland, Ohio, is leading and participating in various projects in partnership with other organizations within GRC and across NASA, the U.S. aerospace industry, and academia to develop advanced controls and health management technologies that will help meet these challenges through the concept of Intelligent Propulsion Systems. The key enabling technologies for an Intelligent Propulsion System are the increased efficiencies of components through active control, advanced diagnostics and prognostics integrated with intelligent engine control to enhance operational reliability and component life, and distributed control with smart sensors and actuators in an adaptive fault tolerant architecture. This presentation describes the current activities of the Controls and Dynamics Branch in the areas of active component control and propulsion system intelligent control, and presents some recent analytical and experimental results in these areas.

Determination of Methanol Content in Herbal Distillates Produced in Urmia Using Spectrophotometry

Directory of Open Access Journals (Sweden)

Mohammad Delirrad

2012-05-01

Full Text Available Background: Herbal distillates have been used for many centuries as drinks, flavors, and herbal medicine in Iran, especially in the city of Urmia. Recently, some studies claimed the presence of methanol in different types of herbal distillates. Methanol is a highly toxic compound which can cause acute or chronic toxicity in humans. Acute poisoning with methanol can cause different complications and even death while chronic methanol exposure has a wide range of nonspecific and misleading findings. The main purpose of this study was to determine methanol content in the commonly-used industrial herbal distillates produced in Urmia. Methods: Five samples of six types of most commonly used herbal distillates (peppermint, musk willow, lemon balm, pennyroyal, dill, and rose water were purchased from five active herbal distillates manufacturers in Urmia. All samples were transferred to the laboratory and methanol content of each sample was measured two times according to the standard method of analysis using spectrophotometer. Results: The lowest and highest concentration of methanol were found in rose water (mean=72.4±32.1 ppm and musk willow (mean=278.3±106 ppm samples, respectively. One-way ANOVA showed statistically significant differences among methanol concentrations in the studied herbal distillates (F=60.9, P <0.001. Discussion: Different amounts of methanol were found in herbal distillates and it seems that there are statistically significant differences in methanol concentrations of various types of herbal distillates. Therefore, considering the harmful effects of methanol on human health, further studies are required for determining permitted levels of methanol in herbal distillates.

Development in Diagnostics Application to Control Advanced Tokamak Plasma

International Nuclear Information System (INIS)

Koide, Y.

2008-01-01

For continuous operation expected in DEMO, all the plasma current must be non-inductively driven, with self-generated neoclassical bootstrap current being maximized. The control of such steady state high performance tokamak plasma (so-called 'Advanced Tokamak Plasma') is a challenge because of the strong coupling between the current density, the pressure profile and MHD stability. In considering diagnostic needs for the advanced tokamak research, diagnostics for MHD are the most fundamental, since discharges which violate the MHD stability criteria either disrupt or have significantly reduced confinement. This report deals with the development in diagnostic application to control advanced tokamak plasma, with emphasized on recent progress in active feedback control of the current profile and the pressure profile under DEMO-relevant high bootstrap-current fraction. In addition, issues in application of the present-day actuators and diagnostics for the advanced control to DEMO will be briefly addressed, where port space for the advanced control may be limited so as to keep sufficient tritium breeding ratio (TBR)

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

A More Efficient Contextuality Distillation Protocol

Science.gov (United States)

Meng, Hui-xian; Cao, Huai-xin; Wang, Wen-hua; Fan, Ya-jing; Chen, Liang

2018-03-01

Based on the fact that both nonlocality and contextuality are resource theories, it is natural to ask how to amplify them more efficiently. In this paper, we present a contextuality distillation protocol which produces an n-cycle box B ∗ B ' from two given n-cycle boxes B and B '. It works efficiently for a class of contextual n-cycle ( n ≥ 4) boxes which we termed as "the generalized correlated contextual n-cycle boxes". For any two generalized correlated contextual n-cycle boxes B and B ', B ∗ B ' is more contextual than both B and B '. Moreover, they can be distilled toward to the maximally contextual box C H n as the times of iteration goes to infinity. Among the known protocols, our protocol has the strongest approximate ability and is optimal in terms of its distillation rate. What is worth noting is that our protocol can witness a larger set of nonlocal boxes that make communication complexity trivial than the protocol in Brunner and Skrzypczyk (Phys. Rev. Lett. 102, 160403 2009), this might be helpful for exploring the problem that why quantum nonlocality is limited.

Distillation Designs for the Lunar Surface

Science.gov (United States)

Boul, Peter J.; Lange,Kevin E.; Conger, Bruce; Anderson, Molly

2010-01-01

Gravity-based distillation methods may be applied to the purification of wastewater on the lunar base. These solutions to water processing are robust physical separation techniques, which may be more advantageous than many other techniques for their simplicity in design and operation. The two techniques can be used in conjunction with each other to obtain high purity water. The components and feed compositions for modeling waste water streams are presented in conjunction with the Aspen property system for traditional stage distillation. While the individual components for each of the waste streams will vary naturally within certain bounds, an analog model for waste water processing is suggested based on typical concentration ranges for these components. Target purity levels for recycled water are determined for each individual component based on NASA s required maximum contaminant levels for potable water Optimum parameters such as reflux ratio, feed stage location, and processing rates are determined with respect to the power consumption of the process. Multistage distillation is evaluated for components in wastewater to determine the minimum number of stages necessary for each of 65 components in humidity condensate and urine wastewater mixed streams.

Process for obtaining a distillation product free from sulfur

Energy Technology Data Exchange (ETDEWEB)

Heyl, G E

1920-06-12

A process is described of obtaining from shale a hydrocarbon product free from sulfur, by distillation, consisting in mixing with the shale a portion of mineral oil and metallic debris, such as turnings and drillings, heating the mixture in a rotary drum and recovering and condensing the vapors distilled.

27 CFR 19.830 - Application of distilled spirits tax.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Application of distilled spirits tax. 19.830 Section 19.830 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Production of Vinegar by the...

Process and apparatus for destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Dalin, D; Hedbaeck, T J

1951-01-10

A process of distilling wood, coal, shale, and like materials in an externally heated retort, consists of heating the retort by burning fuel in a combustion chamber completely or partly surrounding the retort and passing a heat-absorbing medium through ducts which are mounted in or adjacent the greater part of the length of the retort walls which are so arranged as to effect a greater degree of heat extraction at one part of the retort than at another part of the retort. The zones of different heat extraction being related to the heat developed in the combustion chamber maintains the most favourable distillation temperature in all parts of the retort.

Thermal distillation system utilizing biomass energy burned in stove by means of heat pipe

Directory of Open Access Journals (Sweden)

Hiroshi Tanaka

2016-09-01

Full Text Available A thermal distillation system utilizing a part of the thermal energy of biomass burned in a stove during cooking is proposed. The thermal energy is transported from the stove to the distiller by means of a heat pipe. The distiller is a vertical multiple-effect diffusion distiller, in which a number of parallel partitions in contact with saline-soaked wicks are set vertically with narrow gaps of air. A pilot experimental apparatus was constructed and tested with a single-effect and multiple-effect distillers to investigate primarily whether a heat pipe can transport thermal energy adequately from the stove to the distiller. It was found that the temperatures of the heated plate and the first partition of the distiller reached to about 100 °C and 90 °C, respectively, at steady state, showing that the heat pipe works sufficiently. The distilled water obtained was about 0.75 and 1.35 kg during the first 2 h of burning from a single-effect and multiple-effect distillers, respectively.

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study

Science.gov (United States)

1982-01-01

The Current and Advanced Technology ACT control system definition tasks of the Integrated Application of Active Controls (IAAC) Technology project within the Energy Efficient Transport Program are summarized. The systems mechanize six active control functions: (1) pitch augmented stability; (2) angle of attack limiting; (3) lateral/directional augmented stability; (4) gust load alleviation; (5) maneuver load control; and (6) flutter mode control. The redundant digital control systems meet all function requirements with required reliability and declining weight and cost as advanced technology is introduced.

Biodiesel of distilled hydrogenated fat and biodiesel of distilled residual oil: fuel consumption in agricultural tractor

Energy Technology Data Exchange (ETDEWEB)

Camara, Felipe Thomaz da; Lopes, Afonso; Silva, Rouverson Pereira da; Oliveira, Melina Cais Jejcic; Furlani, Carlos Eduardo Angeli [Universidade Estadual Paulista (UNESP), Jaboticabal, SP (Brazil); Dabdoub, Miguel Joaquim [Universidade de Sao Paulo (USP), Ribeirao Preto (Brazil)

2008-07-01

Great part of the world-wide oil production is used in fry process; however, after using, such product becomes an undesirable residue, and the usual methods of discarding of these residues, generally contaminate the environment, mainly the rivers. In function of this, using oil and residual fat for manufacturing biodiesel, besides preventing ambient contamination, turning up an undesirable residue in to fuel. The present work had as objective to evaluate the fuel consumption of a Valtra BM100 4x2 TDA tractor functioning with methylic biodiesel from distilled hydrogenated fat and methylic biodiesel from distilled residual oil, in seven blends into diesel. The work was conducted at the Department of Agricultural Engineering, at UNESP - Jaboticabal, in an entirely randomized block statistical design, factorial array of 2 x 7, with three repetitions. The factors combinations were two types of methylic distilled biodiesel (residual oil and hydrogenated fat) and seven blends (B{sub 0}, B{sub 5}, B{sub 1}5, B{sub 2}5, B{sub 5}0, B{sub 7}5 and B{sub 1}00). The results had evidenced that additioning 15% of biodiesel into diesel, the specific consumption was similar, and biodiesel of residual oil provided less consumption than biodiesel from hydrogenated fat. (author)

Cachaça distillation investigated on the basis of model systems

Directory of Open Access Journals (Sweden)

H. F. A. Scanavini

2012-06-01

Full Text Available This work reports experimental tests using commercial spirits that were diluted and had their initial composition modified in order to better measure the distillation behavior of selected minor compounds of importance for the quality of alcoholic beverages. Such compounds were added to the commercial cachaça and the corresponding model wine, obtained after the spirits' dilution, was distilled. In this way a more precise distillation profile could be determined for those minor compounds. The alembic heating was performed by electrical resistance and the corresponding heat transfer coefficient was determined by analyzing the thermal behavior of the still during the distillations. A simulation algorithm was developed, including the mass and enthalpy balances as well as the heat transfer flux to the boiling wine. Good agreement between experimental and simulated results was obtained for the distillate rate, alcoholic graduation, temperature and most minor component profiles.

Process and apparatus for distilling bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

Veyrier, J A

1922-03-27

This process of distillation of bituminous minerals and particularly bituminous limestone is characterized by the fact that the minerals are introduced into the retort where they stand only the temperature necessary to distill the water and lighter oils that they contain and then are drawn out into the hearth and serve for heating the retort. The apparatus is characterized by the fact that the retort has a screw conveyor, placed in the flue of the hearth, supplied with a chamber for evacuation below this hearth.

Static multiplicities in heterogeneous azeotropic distillation sequences

DEFF Research Database (Denmark)

Esbjerg, Klavs; Andersen, Torben Ravn; Jørgensen, Sten Bay

1998-01-01

In this paper the results of a bifurcation analysis on heterogeneous azeotropic distillation sequences are given. Two sequences suitable for ethanol dehydration are compared: The 'direct' and the 'indirect' sequence. It is shown, that the two sequences, despite their similarities, exhibit very...... different static behavior. The method of Petlyuk and Avet'yan (1971), Bekiaris et al. (1993), which assumes infinite reflux and infinite number of stages, is extended to and applied on heterogeneous azeotropic distillation sequences. The predictions are substantiated through simulations. The static sequence...

Evaluation of sulfonated carbon as catalyst in reactive distillation

International Nuclear Information System (INIS)

Orjuela, Alvaro; Civetta, Nicolas; Rivera, Jairo; Boyaca, Alejandro; Diaz, Jesus

2004-01-01

A packed bed using sulfonated coal catalytic pellets was prepared using a Colombian anthracitic coal. Such pellets were introduced in a semi batch distillation column to which acetic acid and ethanol were fed in order to determine experimentally the feasibility of obtaining ethyl acetate by reactive distillation operation. The carbonaceous catalytic packing was characterized by total exchange capacity, potentiometric titration and BET area. Experimental tests were carried out using three acid/alcohol ratios. Results of such process are shown by reaction conversion and concentration in distillate and bottom products. The sulfonated coal showed catalytic activity in this esterification reaction, with conversions between 29-45%

Use of solar distillation for olive mill wastewater drying and recovery of polyphenolic compounds.

Science.gov (United States)

Sklavos, Sotirios; Gatidou, Georgia; Stasinakis, Athanasios S; Haralambopoulos, Dias

2015-10-01

Olive mill wastewater (OMW) is characterized by its high organic load and the presence of phenolic compounds. For first time, a solar distillator was used to investigate the simultaneous solar drying of OMW and the recovery of phenolic compounds with antioxidant properties in the distillate. Two experiments were conducted and the role of thermal insulation on the performance of the distiller was studied. The use of insulation resulted to higher temperatures in the distillator (up to 84.3 °C and 78.5 °C at the air and sludge, respectively), shorter period for OMW dewatering (14 days), while it increased the performance of distillator by 26.1%. Chemical characterization of the distillate showed that pH and COD concentration gradually decreased during the experiments, whereas an opposite trend was noticed for conductivity and total phenols concentration. Almost 4% of the total phenols found initially in OMW were transferred to the distillate when an insulated solar distillator was used. Gas chromatographic analysis of collected distillates confirmed the presence of tyrosol in all samples; whereas hydroxytyrosol was found only in fresh collected distillate samples. Further experiments should be conducted to optimize the process and quantify the concentrations of recovered phenolic compounds. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Design and Manufacturing of Essential oil Distillation Plant for ...

African Journals Online (AJOL)

The Design and Manufacturing of Essential oil Distillation Plant for rural poverty ... The adaptation of oil distillation technology for essential oil production is ... based on local resources and the first prototype has been manufactured and tested.

Optimization study of distillation column based on Type I absorption heat pump

International Nuclear Information System (INIS)

Li, Yan; Wang, Lu; Zhu, Meng; Wang, Weiqin

2017-01-01

Highlights: • Propose a new distillation system based on Type I absorption heat pump. • The optimum condition of the system is obtained. • The energy consumption of the system is reduced by 23.3% significantly. • The benefits of economy and energy-saving for the new distillation system are distinct. - Abstract: Due to the thermodynamic deficiencies in general pressurized distillation process, a new distillation system based on Type I AHP (absorption heat pump) is proposed in this paper. The proposed system uses AHP to recover the waste heat from column condenser and reheat the feed materials of column; meanwhile, the cooling capacity of column condenser can be increased, which leads to the decrease of the pressure in distillation column. With general distillation system of depropanizing column (C-101) as an example, using numerical simulation software Aspen Plus, the effect of inner parameters on the energy consumption has been conducted to approach the general rules of energy saving in distillation. Then the new distillation system is adopted and the optimization of its energy consumption is conducted to determine the optimum operating condition. The numerical simulation results show that the steam consumption can be decreased by 23.3% compared with general C-101 system, reaching the minimum. Moreover, the extra heat output of AHP is treated as the heat source for the reboilers of deethanization column (C-102) and refined propylene column (C-103), which reduces the total steam consumption of three-column processes by 22.1%.

Mechanics and model-based control of advanced engineering systems

CERN Document Server

Irschik, Hans; Krommer, Michael

2014-01-01

Mechanics and Model-Based Control of Advanced Engineering Systems collects 32 contributions presented at the International Workshop on Advanced Dynamics and Model Based Control of Structures and Machines, which took place in St. Petersburg, Russia in July 2012. The workshop continued a series of international workshops, which started with a Japan-Austria Joint Workshop on Mechanics and Model Based Control of Smart Materials and Structures and a Russia-Austria Joint Workshop on Advanced Dynamics and Model Based Control of Structures and Machines. In the present volume, 10 full-length papers based on presentations from Russia, 9 from Austria, 8 from Japan, 3 from Italy, one from Germany and one from Taiwan are included, which represent the state of the art in the field of mechanics and model based control, with particular emphasis on the application of advanced structures and machines.

Removal of salt from rare earth precipitates by vacuum distillation

International Nuclear Information System (INIS)

Yang, Hee-Chul; Eun, Hee-Chul; Cho, Yong-Zun; Park, Hwan-Seo; Kim, In-Tae

2008-01-01

This study investigated the distillation rates of LiCl-KCl eutectic salt from the rare earth (RE) precipitates originating from the oxygen-sparging RE precipitation process. The first part study investigated distillation rates of eutectic salt under different vacuums at high temperatures by using thermo-gravimetric furnace system. The second part study tested the removal efficiency of eutectic salt from RE precipitates by using the laboratory vacuum distillation furnace system. Investigated variables were the temperature, the degree of vacuum and the time. Salt distillation operation with a moderated distillation rate of 10 -4 - 10 -5 mole sec -1 cm -2 is possible at temperature less than 1300 K and vacuums of 5-50 Torr, by minimizing the potentials of the RE particle entrainment. An increase in the vaporizing surface area is relatively effective for removing the residual salt in pores of bulk of the precipitated RE particles, when compared to that for the vaporizing time. Over 99.9% of the salt removal from the salt-RE precipitate mixture could be achieved by increasing the vaporizing surface area under moderate vacuum conditions of 50 Torr at 1200 K. (author)

Human factors survey of advanced instrumentation and controls

International Nuclear Information System (INIS)

Carter, R.J.

1989-01-01

A survey oriented towards identifying the human factors issues in regard to the use of advanced instrumentation and controls (I ampersand C) in the nuclear industry was conducted. A number of United States (US) and Canadian nuclear vendors and utilities were participants in the survey. Human factors items, subsumed under the categories of computer-generated displays (CGD), controls, organizational support, training, and related topics, were discussed. The survey found the industry to be concerned about the human factors issues related to the implementation of advanced I ampersand C. Fifteen potential human factors problems were identified. They include: the need for an advanced I ampersand C guideline equivalent to NUREG-0700; a role change in the control room from operator to supervisor; information overload; adequacy of existing training technology for advanced I ampersand C; and operator acceptance and trust. 11 refs., 1 tab

Experimental entanglement distillation of mesoscopic quantum states

DEFF Research Database (Denmark)

Dong, Ruifang; Lassen, Mikael Østergaard; Heersink, Joel

2008-01-01

channel, the distribution of loss-intolerant entangled states is inevitably afflicted by decoherence, which causes a degradation of the transmitted entanglement. To combat the decoherence, entanglement distillation, a process of extracting a small set of highly entangled states from a large set of less...... entangled states, can be used(4-14). Here we report on the distillation of deterministically prepared light pulses entangled in continuous variables that have undergone non-Gaussian noise. The entangled light pulses(15-17) are sent through a lossy channel, where the transmission is varying in time similarly...

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Jacomini, V V

1938-06-07

To produce valuable oils from shale by continuous distillation it is preheated by a heated fluid and introduced into a distilling retort from which the oil vapours and spent material are separately removed and the vapours condensed to recover the oil. The shale is preheated to 400 to 500/sup 0/F in the hopper by combustion gases from a flue and is fed in measured quantities to a surge drum, a loading chamber and surge drum, the latter two being connected to a steam pipe which equalises the pressure thereon. The material passes by two screw conveyors to a retort with deflector bars to scatter the material so that lean hot cycling gas flowing through a pipe is spread out as it makes its way upwardly through the shale and heats the oil so that it is driven off as vapour, collected in the lean gas and carried off through an outlet pipe. A measuring valve is provided at the bottom of a retort and cutter knives cut the spent shale and distribute cooling water thereto. The gases travel through heat exchangers and a condenser to an accumulator where the cycling gas is separated from the vapours, passed to compression, and preheated in a gas exchanger and spiral coils before it is returned to the retort. The oil passes to a storage tank by way of a unit tank in which oil vapours are recovered. Water is collected by a pipe in the tank bottom and returned by shaft to a retort.

Displacement-enhanced entanglement distillation of single-mode-squeezed entangled states

DEFF Research Database (Denmark)

Tipsmark, Anders; Neergaard-Nielsen, Jonas Schou; Andersen, Ulrik Lund

2013-01-01

It has been shown that entanglement distillation of Gaussian entangled states by means of local photon subtraction can be improved by local Gaussian transformations. Here we show that a similar effect can be expected for the distillation of an asymmetric Gaussian entangled state that is produced...... by a single squeezed beam. We show that for low initial entanglement, our largely simplified protocol generates more entanglement than previous proposed protocols. Furthermore, we show that the distillation scheme also works efficiently on decohered entangled states as well as with a practical photon...

27 CFR 28.281 - Certificate of use for distilled spirits and wines.

Science.gov (United States)

2010-04-01

... distilled spirits and wines. 28.281 Section 28.281 Alcohol, Tobacco Products and Firearms ALCOHOL AND... Ports of Export Lading for Use on Aircraft § 28.281 Certificate of use for distilled spirits and wines. When all of the distilled spirits or wines represented by a single application, notice, or claim, TTB...

Evaluation of robotically controlled advanced endoscopic instruments

NARCIS (Netherlands)

Reilink, Rob; Kappers, Astrid M.L.; Stramigioli, Stefano; Misra, Sarthak

Background Advanced flexible endoscopes and instruments with multiple degrees of freedom enable physicians to perform challenging procedures such as the removal of large sections of mucosal tissue. However, these advanced endoscopes are difficult to control and require several physicians to

Simulators of tray distillation columns as tools for interpreting ...

African Journals Online (AJOL)

... at 0.05 m intervals were determined from top to the bottom of simulators of tray distillation columns exposed to 20 mCi of 137 Cs. Signals generated from the simulators were identical with the experimental signals obtained from the Stabilizer Column of the crude oil distillation unit at the Tema Oil Refinery Ghana Limited.

Advanced Controllers for Electromechanical Motion Systems

NARCIS (Netherlands)

Nguyen, Duy Cuong

2008-01-01

The aim of this research is to develop advanced controllers for electromechanical motion systems. In order to increase efficiency and reliability, these control systems are required to achieve high performance and robustness in the face of model uncertainty, measurement noise, and reproducible

Konference Distillation and Absorption 2010

Czech Academy of Sciences Publication Activity Database

Bendová, Magdalena

2009-01-01

Roč. 103, č. 10 (2009), s. 862 ISSN 0009-2770 R&D Projects: GA MŠk LA320 Institutional research plan: CEZ:AV0Z40720504 Keywords : conference * announcement * distillation and absorption Subject RIV: CF - Physical ; Theoretical Chemistry

The forms of azeotropic rule for multidimensional diagrams of equilibrium distillation

Science.gov (United States)

Pisarenko, Yu. A.; Usol'tseva, O. O.; Cardona, C. A.; Gerard, O. T.

2013-09-01

Linear independent forms of the azeotropy rule applicable to diagrams of distillation (reaction distillation) and their fragments are established and presented as simple polyhedra of arbitrary dimensions.

Distillation with Sublogarithmic Overhead

Science.gov (United States)

Hastings, Matthew B.; Haah, Jeongwan

2018-02-01

It has been conjectured that, for any distillation protocol for magic states for the T gate, the number of noisy input magic states required per output magic state at output error rate ɛ is Ω [log (1 /ɛ )] . We show that this conjecture is false. We find a family of quantum error correcting codes of parameters ⟦ ∑ i =w +1 m (m i ),∑ i =0 w (m i ),∑ i =w +1 r +1 (r +1 i )⟧ for any integers m >2 r , r >w ≥0 , by puncturing quantum Reed-Muller codes. When m >ν r , our code admits a transversal logical gate at the ν th level of Clifford hierarchy. In a distillation protocol for magic states at the level ν =3 (T gate), the ratio of input to output magic states is O (logγ(1 /ɛ )) , where γ =log (n /k )/log (d )<0.678 for some m , r , w . The smallest code in our family for which γ <1 is on ≈258 qubits.

Cooperative research for human factors review of advanced control rooms

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Park, Jae Chang; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul

2000-12-01

This project has been performed as cooperative research between KAERI and USNRC. Human factors issues related to soft controls, which is one of key features of advanced HSI, are identified in this project. The issues are analyzed for the evaluation approaches in either experimental or analytical ways. Also, issues requiring additional researches for the evaluation of advanced HSI are identified in the areas of advanced information systems design, computer-based procedure systems, soft controls, human systems interface and plant modernization process, and maintainability of digital systems. The issues are analyzed to discriminate the urgency of researches on it to high, medium, and low levels in consideration of advanced HSI development status in Korea, and some of the issues that can be handled by experimental researches are identified. Additionally, an experimental study is performed to compare operator's performance on human error detection in advanced control rooms vs. in conventional control rooms. It is found that advanced control rooms have several design characteristics hindering operator's error detection performance compared to conventional control rooms.

Cooperative research for human factors review of advanced control rooms

International Nuclear Information System (INIS)

Lee, Jung Woon; Park, Jae Chang; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul

2000-12-01

This project has been performed as cooperative research between KAERI and USNRC. Human factors issues related to soft controls, which is one of key features of advanced HSI, are identified in this project. The issues are analyzed for the evaluation approaches in either experimental or analytical ways. Also, issues requiring additional researches for the evaluation of advanced HSI are identified in the areas of advanced information systems design, computer-based procedure systems, soft controls, human systems interface and plant modernization process, and maintainability of digital systems. The issues are analyzed to discriminate the urgency of researches on it to high, medium, and low levels in consideration of advanced HSI development status in Korea, and some of the issues that can be handled by experimental researches are identified. Additionally, an experimental study is performed to compare operator's performance on human error detection in advanced control rooms vs. in conventional control rooms. It is found that advanced control rooms have several design characteristics hindering operator's error detection performance compared to conventional control rooms

Simulation of ethanol extractive distillation with mixed glycols as separating agent

Directory of Open Access Journals (Sweden)

I. D. Gil

2014-03-01

Full Text Available Extractive distillation is an alternative for ethanol dehydration processes that has been shown to be more effective than azeotropic distillation and, in close proximity, to be very competitive against the process that uses adsorption with molecular sieves. Glycols have been shown to be the most effective solvents in extractive distillation, mainly ethylene glycol and glycerol. In this work, an extractive distillation column was simulated with the Aspen Plus software platform, using the RadFrac module for distillation columns, to investigate the effect on the separation of the ethylene glycol-glycerol mixture composition, the separating agent feed stages, the separating agent split stream feed, and the azeotropic feed temperature. The NRTL model was used to calculate the phase equilibrium of these strongly polar mixtures. A rigorous simulation of the extractive distillation column finally established was also performed, including a secondary recovery column for the mixture of solvents and a recycle loop, to simulate an industrially relevant situation. This simulation allowed establishing the complete parameters to dehydrate ethanol: the optimal stage for separating agent feed is stage 4; the most adequate composition for the glycols mixture is 60 mol% ethylene glycol and 40 mol% glycerol. Finally, energetically efficient operating conditions for each one of the columns were established through a preliminary pinch analysis.

Solar desalination by freezing and distillation

Science.gov (United States)

Kvajic, G.

It is noted that among seawater desalination processes the absorption-freeze vapor compression processes based on the thermal heat pump, although untested commercially and still in the development stage, appears technically and economically an attractive application of low-grade (exergy) solar heat. The distillation processes proposed here may be conveniently powered by low-grade solar heat (from flat plate solar collectors). It is expected that the scaling problem will be insignificant in comparison with that encountered in the conventional multistage flash process. The novel feature here is the use of enlarged capacity for heat exchange between distillate and brine via latent heat of solid-liquid phase change of a suitable hydrophobic intermediate heat transfer material.

Companded total condensation loxboil air distillation

International Nuclear Information System (INIS)

Erickson, D.C.

1989-01-01

This patent describes a dual pressure cryogenic distillation process for producing gaseous oxygen from a supply of compressed and cleaned air, comprising: a. cooling a major fraction of the compressed and cleaned air; b. rectifying the major fraction in a high pressure rectifier to liquid nitrogen overhead product and kettle liquid bottom product; c. distilling the kettle liquid in a low pressure column to liquid oxygen bottom product and gaseous nitrogen overhead product; d. working expanding a compensating vapor comprised of at least 77% N/sub 2/ thereby producing refrigeration; and e. further compressing the remaining minor fraction comprising no more than about 30% of the compressed, cleaned warm air in a compressor powered by the expansion

Fractionation of nitrogen-15 during distillation of ammonia in an all-glass still

International Nuclear Information System (INIS)

O'Deen, W.A.; Porter, L.K.

1980-01-01

The detection of N isotopic fractionation during distillation in an all-glass Kjeldahl distillation apparatus is reported. Five milligrams of N from (NH 4 ) 2 SO 4 in 100 ml of solution at a 1.3 atom % 15 N level were distilled from a 250 ml boiling flask through a Kontes Kjeldahl distillation apparatus. The solution was made basic with 1 ml of 13N NaOH and distillate was collected sequentially in three glass shell vials, and then in a 100 ml beaker, each containing .5ml of 1N HCl. Three ml of distillate were collected in each vial and 40 ml in the beaker. The first distilled N-fraction was lower in atom % 15 N than the standard. In subsequent fractions, atom % 15 N values increased until the last fraction was higher than the undistilled standard. The last fraction differed from the first fraction and standard significantly at the 0.01 level. The first fraction differed significantly from the standard at the 0.05 probability level by 3.2 parts per thousand. Data indicated that atom % 15 N distillation values can be expected to be slightly lower than undistilled values owing to N isotopic fractionation. 1 table

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

1915-07-03

Oils are extracted from coal, lignite, shale, boghead, butumen, asphalt, tar, pitch, etc., by distillation at a low temperature, which may be 300 to 425/sup 0/CC, solvent oils or vapors being circulated during the heating which may be conducted with or without increased or reduced pressure. The solvent oils and the extracted oils are recovered in condensers, etc., last traces being expelled from the material by a current of water vapor. The uncondensed gases may be used for heating, and the solid residue may be used for the production of gas and coke, or may be briquetted.

19 CFR 11.6 - Distilled spirits, wines, and malt liquors in bulk.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Distilled spirits, wines, and malt liquors in bulk...; DEPARTMENT OF THE TREASURY PACKING AND STAMPING; MARKING Packing and Stamping § 11.6 Distilled spirits, wines... conveying imported distilled spirits, wines, and malt liquors, in accordance with 19 U.S.C. 467. (b) Marks...

Multi-saline sample distillation apparatus for hydrogen isotope analyses : design and accuracy

Science.gov (United States)

Hassan, Afifa Afifi

1981-01-01

A distillation apparatus for saline water samples was designed and tested. Six samples may be distilled simultaneously. The temperature was maintained at 400 C to ensure complete dehydration of the precipitating salts. Consequently, the error in the measured ratio of stable hydrogen isotopes resulting from incomplete dehydration of hydrated salts during distillation was eliminated. (USGS)

Logic hybrid simulation-optimization algorithm for distillation design

OpenAIRE

Caballero Suárez, José Antonio

2014-01-01

In this paper, we propose a novel algorithm for the rigorous design of distillation columns that integrates a process simulator in a generalized disjunctive programming formulation. The optimal distillation column, or column sequence, is obtained by selecting, for each column section, among a set of column sections with different number of theoretical trays. The selection of thermodynamic models, properties estimation etc., are all in the simulation environment. All the numerical issues relat...

Solvent distillation studies for a purex reprocessing plant

International Nuclear Information System (INIS)

Ginisty, C.; Guillaume, B.

1990-01-01

A distillation system has been developed for regeneration of Purex solvent and will be implemented for the first time in a reprocessing plant. The results are described and analyzed, with emphasis on laboratory experiments which were made with a radioactive plant solvent. Particularly the distillation provides a good separation of solvent degradation products, which was verified by measurements of interfacial tension and plutonium or ruthenium retention. 16 refs., 3 figs., 5 tabs

Sulfur and selenium isotope separation by distillation

International Nuclear Information System (INIS)

Mills, T. R.; McInteer, B. B.; Montoya, J. G.

1988-01-01

Sulfur and selenium isotopes are used for labeled compounds and as precursors for radioisotope production; however, both limited availability and high costs are problems. A new method is needed for large-scale separation of these isotopes. Experimental distillation columns were used to measure isotopic separations for sulfur and selenium compounds. The maximum total isotope separation of 32 S vs. 34 S were 1.127 for H 2 S, 1.048 for COS, 0.838 for SF 4 , and 1.058 for CH 3 SH. Relative volatilities of 32 S vs. 34 S are 1.0006 for COS and 0.9976 for SF 4 . There is a reverse isotope effect for carbon in COS. No isotopic separation was observed for dimethyl selenide. The lower mass selenium isotopes in H 2 Se are more volatile. Distillation is a promising method for separating sulfur isotopes on a production scale. Existing distillation technology produced separated isotopes with an effect similar to that found for sulfur in SF 4 . 8 refs., 2 tabs

Sulfur and selenium isotope separation by distillation

International Nuclear Information System (INIS)

Mills, T.R.; McInteer, B.B.; Montoya, J.G.

1989-01-01

Sulfur and selenium isotopes are used for labeled compounds and as precursors for radioisotope production; however, both limited availability and high costs are problems. A new method is needed for large-scale separation of theses isotopes. Experimental distillation columns were used to measure isotopic separations for sulfur and selenium compounds. The maximum total isotope separations of 32 S vs. 34 S were 1.127 for H 2 S, 1.048 for COS, 0.838 for SF 4 , and 1.058 for CH 3 SH. Relative volatilities of 32 S and 34 S are 1.0006 for COS and 0.9976 for SF 4 . There is a reverse isotope effect for carbon in COS. No isotopic separation was observed for dimethyl selenide. The lower mass selenium isotopes in H 2 Se are more volatile. Distillation is a promising method for separating sulfur isotopes on a production scale. Existing distillation technology produces separated isotopes with an effect similar to that found for sulfur in SF 4 . (author). 8 refs.; 2 tabs

Memstill® - Low cost membrane distillation technology for seawater desalination

NARCIS (Netherlands)

Hanemaaijer, J.H.

2004-01-01

Despite widespread research and development efforts during the last 25 years, membrane distillation still is not an accepted process for seawater desalination. A consortium of nine parties is presently developing a modified air gap membrane distillation (AGMD) process, aiming at presenting a

Potential Health Risk of Herbal Distillates and Decoctions Consumption in Shiraz, Iran.

Science.gov (United States)

Moore, F; Akhbarizadeh, R; Keshavarzi, B; Tavakoli, F

2015-10-01

Concentration of 26 elements in 16 different herbal distillates and 5 herbal decoctions, were determined using inductively coupled plasma-mass spectrometry (ICP-MS). The elemental content of five raw herbal materials used for making decoctions and seven distilled and boiled residues were also evaluated by inductively coupled plasma optical emission spectrometry (ICP-OES). The results indicated that herbal products display a wide range of elemental concentrations. Compared with world health regulations, the concentrations of the elements in herbal distillates and decoctions did not exceed the recommended limits. The analysis of herbal extracts did not show a significant transfer of toxic elements during decoction preparation. Comparison of elemental content among fresh herbal material and herbal distillate and decoction of the same herb showed that, besides the elemental abundance of herbal organs, the ionic potential of elements also play an important role in elemental content of herbal products. Based on the results of the research, it seems that most health benefits attributed to herbal products (especially herbal distillates) are more related to their organic compounds rather than elemental composition. Calculated hazard quotient (HQ) and hazard index (HI) were used to evaluate the noncarcinogenic health risk from individual and combined metals via daily consumption of 100 ml of herbal distillates and 250 ml of herbal decoctions. Both HQs and HI through consumption of herbal distillates and herbal decoctions (except Valerian) were below 1. Apparently, daily consumption of herbal distillates and decoctions at the indicated doses poses no significant health risk to a normal adult.

A Randomized Controlled Trial Comparing the Letter Project Advance Directive to Traditional Advance Directive.

Science.gov (United States)

Periyakoil, Vyjeyanthi S; Neri, Eric; Kraemer, Helena

2017-09-01

Simpler alternatives to traditional advance directives that are easy to understand and available in multiple formats and can be initiated by patients and families will help facilitate advance care planning. The goal of this study was to compare the acceptability of the letter advance directive (LAD) to the traditional advance directive (TAD) of the state of California. A web-based, randomized controlled trial was conducted, in which the participants were randomized to one of two types of advance directives (ADs): the LAD (intervention) or the TAD (control). Primary outcomes were participant ratings of the ease, value, and their level of comfort in the AD document they completed. A total of 400 participants completed the study, with 216 randomized to the LAD and 184 to the TAD by a computerized algorithm. Overall, participants preferred the LAD to the TAD (success rate difference [SRD] = 0.46, 95th percentile confidence interval [CI]: 0.36-0.56, p advance directive to be a better alternative to the traditional advance directive form.

INTEGRATED PLASMA CONTROL FOR ADVANCED TOKAMAKS

International Nuclear Information System (INIS)

HUMPHREYS, D.A.; FERRON, J.R.; JOHNSON, R.D; LEUER, J.A.; PENAFLOR, B.G.; WALKER, M.L.; WELANDER, A.S.; KHAYRUTDINOV, R.R; DOKOUKA, V.; EDGELL, D.H.; FRANSSON, C.M.

2004-03-01

OAK-B135 Advanced tokamaks (AT) are distinguished from conventional tokamaks by their high degree of shaping, achievement of profiles optimized for high confinement and stability characteristics, and active stabilization of MHD instabilities to attain high values of normalized beta and confinement. These high performance fusion devices thus require accurate regulation of the plasma boundary, internal profiles, pumping, fueling, and heating, as well as simultaneous and well-coordinated MHD control action to stabilize such instabilities as tearing modes and resistive wall modes. Satisfying the simultaneous demands on control accuracy, reliability, and performance for all of these subsystems requires a high degree of integration in both design and operation of the plasma control system in an advanced tokamak. The present work describes the approach, benefits, and progress made in integrated plasma control with application examples drawn from the DIII-D tokamak. The approach includes construction of plasma and system response models, validation of models against operating experiments, design of integrated controllers which operate in concert with one another as well as with supervisory modules, simulation of control action against off-line and actual machine control platforms, and iteration of the design-test loop to optimize performance

Carbon-13 isotopic composition of distillation fractions of some Egyptian crude oils

International Nuclear Information System (INIS)

Aly, A.I.M.; Hamza, M.S.; Abd Elsamie, S.G.

1991-01-01

13 C/ 13 C ratios were determined for some crude oil fields in the Gulf of Suez and Western Desert provinces. The crude oil was subjected to distillation at atmospheric pressure and subsequently under vacuum. Distillation fractions were collected at 25 degree C intervals. Carbon-13 content of these distillation fractions showed some differences in the degree of isotopic fractionation. The results were interpreted in view of the age of the source rocks and the degree of maturation process. The carbon-13 content of distillation fractions may be helpful in revealing petroleum mechanisms which can be exploited in exploration.4 fig

Development of a model for the synthesis of unsaturated polyester by reactive distillation

NARCIS (Netherlands)

Shah, M.R.; Zondervan, E.; Oudshoorn, M.L.; Haan, de A.B.; Haan, de A.B.; Kooijman, H.; Górak, A.

2010-01-01

Traditionally polyester production is done in a batch reactor equipped with a separation column for batch distillation. A promising alternative for the intensification of this process is reactive distillation. In this paper, a reactive distillation model is developed for the synthesis of an

Model-free adaptive control of advanced power plants

Science.gov (United States)

Cheng, George Shu-Xing; Mulkey, Steven L.; Wang, Qiang

2015-08-18

A novel 3-Input-3-Output (3.times.3) Model-Free Adaptive (MFA) controller with a set of artificial neural networks as part of the controller is introduced. A 3.times.3 MFA control system using the inventive 3.times.3 MFA controller is described to control key process variables including Power, Steam Throttle Pressure, and Steam Temperature of boiler-turbine-generator (BTG) units in conventional and advanced power plants. Those advanced power plants may comprise Once-Through Supercritical (OTSC) Boilers, Circulating Fluidized-Bed (CFB) Boilers, and Once-Through Supercritical Circulating Fluidized-Bed (OTSC CFB) Boilers.

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Griffiths, C A

1924-04-15

In apparatus of the kind set forth for distilling solid carbonaceous materials, a rotary retort in the form of a tubular, hollow cylindrical, or other similar hollow body, of small diameter, having a thin wall is provided to which the heat is applied externally, with means operative within it adapted, not only for cleaning the internal wall of the retort but also for distributing the heat throughout the mass of materials under treatment, substantially as described.

Experiment-Based Teaching in Advanced Control Engineering

Science.gov (United States)

Precup, R.-E.; Preitl, S.; Radac, M.-B.; Petriu, E. M.; Dragos, C.-A.; Tar, J. K.

2011-01-01

This paper discusses an experiment-based approach to teaching an advanced control engineering syllabus involving controlled plant analysis and modeling, control structures and algorithms, real-time laboratory experiments, and their assessment. These experiments are structured around the representative case of the longitudinal slip control of an…

Using commercial simulators for determining flash distillation curves for petroleum fractions

OpenAIRE

Eleonora Erdmann; Demetrio Humana; Samuel Franco Domínguez; Lorgio Mercado Fuentes

2010-01-01

This work describes a new method for estimating the equilibrium flash vaporisation (EFV) distillation curve for petro-leum fractions by using commercial simulators. A commercial simulator was used for implementing a stationary mo-del for flash distillation; this model was adjusted by using a distillation curve obtained from standard laboratory ana-lytical assays. Such curve can be one of many types (eg ASTM D86, D1160 or D2887) and involves an experimental procedure simpler than that required...

27 CFR 27.61 - Containers of distilled spirits to bear closures.

Science.gov (United States)

2010-04-01

... BEER General Requirements Closures for Containers of Distilled Spirits § 27.61 Containers of distilled spirits to bear closures. No person shall transport, buy, possess, or sell, or transfer any imported...

ITER task T332a (1996) low-inventory cryogenic distillation tests

International Nuclear Information System (INIS)

Woodall, K.; Bellamy, D.

1997-02-01

The overall objective of this ITER task was to perform tests which would improve the accuracy of the ITER Isotope Separation System (ISS) tritium inventory estimates and to allow designers to lower the tritium and hydrogen inventory estimates. The work program was also designed to give a better understanding of cryogenic distillation hydraulics and provide information which would improve process control. The work program this year addressed the following specific task objectives. Measure the detailed hydraulics for deuterium/deuterium hydride mixtures in a cryogenic distillation column using Helipak C packing. Determine maximum vapour velocity, HETP and tritium and deuterium inventory data for a column that can be operated right up to flooding conditions. Determine if a proprietary surface treatment improves the wetting characteristics for hydrogen on stainless steel packing. Measure the isotope separation and inventory performance of a Helipak C column large enough to handle up to 45 mm. Investigate additional hydraulic effects in the reboiler and column. 7 refs., 7 figs

MultiController: the PLC-SCADA object for advanced regulation

CERN Document Server

Ortola, J

2007-01-01

Nowadays, industrial solutions with PLCs (Programmable Logic Controllers) have basic control loop features. The SCADA (Supervisory Control And Data Acquisition) system is a key point of the process control system due to an efficient HMI (Human Machine Interfaces) that provides an open method of tuning and leading possibilities. As a consequence, advanced control algorithms have to be developed and implemented for those PLC-SCADA solutions in order to provide perspectives in solving complex and critical regulation problems. The MultiController is an object integrated for a large scale project at CERN (the European Organization for Nuclear Research) named LHC-GCS (Large Hadron Collider - Gas Control System). It is developed for a Framework called CERN-UNICOS based on PLC-SCADA facilities. The MultiController object offers various advanced control loop strategies. It gives to the user advanced control algorithms like PID, Smith Predictor, PFC, GPC and RST. It is implemented as a monolithic entity (in PLC and SCA...

Sustaining high energy efficiency in existing processes with advanced process integration technology

International Nuclear Information System (INIS)

Zhang, Nan; Smith, Robin; Bulatov, Igor; Klemeš, Jiří Jaromír

2013-01-01

Highlights: ► Process integration with better modelling and more advanced solution methods. ► Operational changes for better environmental performance through optimisation. ► Identification of process integration technology for operational optimisation. ► Systematic implementation procedure of process integration technology. ► A case study with crude oil distillation to demonstrate the operational flexibility. -- Abstract: To reduce emissions in the process industry, much emphasis has been put on making step changes in emission reduction, by developing new process technology and making renewable energy more affordable. However, the energy saving potential of existing systems cannot be simply ignored. In recent years, there have been significant advances in process integration technology with better modelling techniques and more advanced solution methods. These methods have been applied to the new design and retrofit studies in the process industry. Here attempts are made to apply these technologies to improve the environmental performance of existing facilities with operational changes. An industrial project was carried out to demonstrate the importance and effectiveness of exploiting the operational flexibility for energy conservation. By applying advanced optimisation technique to integrate the operation of distillation and heat recovery in a crude oil distillation unit, the energy consumption was reduced by 8% without capital expenditure. It shows that with correctly identified technology and the proper execution procedure, significant energy savings and emission reduction can be achieved very quickly without major capital expenditure. This allows the industry to improve its economic and environment performance at the same time.

Automated Deployment of Advanced Controls and Analytics in Buildings

Science.gov (United States)

Pritoni, Marco

Buildings use 40% of primary energy in the US. Recent studies show that developing energy analytics and enhancing control strategies can significantly improve their energy performance. However, the deployment of advanced control software applications has been mostly limited to academic studies. Larger-scale implementations are prevented by the significant engineering time and customization required, due to significant differences among buildings. This study demonstrates how physics-inspired data-driven models can be used to develop portable analytics and control applications for buildings. Specifically, I demonstrate application of these models in all phases of the deployment of advanced controls and analytics in buildings: in the first phase, "Site Preparation and Interface with Legacy Systems" I used models to discover or map relationships among building components, automatically gathering metadata (information about data points) necessary to run the applications. During the second phase: "Application Deployment and Commissioning", models automatically learn system parameters, used for advanced controls and analytics. In the third phase: "Continuous Monitoring and Verification" I utilized models to automatically measure the energy performance of a building that has implemented advanced control strategies. In the conclusions, I discuss future challenges and suggest potential strategies for these innovative control systems to be widely deployed in the market. This dissertation provides useful new tools in terms of procedures, algorithms, and models to facilitate the automation of deployment of advanced controls and analytics and accelerate their wide adoption in buildings.

Ionic liquid screening for ethylbenzene/styrene separation by extractive distillation

NARCIS (Netherlands)

Jongmans, M.T.G.; Schuur, B.; Haan, de A.B.

2011-01-01

The separation of ethylbenzene from styrene by distillation is very energy-intensive, because of the low relative volatility (1.3–1.4). Extractive distillation is a promising alternative to separate the close boiling mixture, in which the solvent selection is crucial for the process feasibility. In

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Ironside, T G

1921-09-01

In the distillation of carbonaceous material such as shale, coal, lignite, wood or liquid hydrocarbons, the material is mixed with a heated granular substance such as sand which supplies the necessary heat. The shale or the like, which may be preheated, is fed from a hopper by a worm conveyer to a tube leading into a retort, and the heated granular material such as sand is supplied from a jacketed container through a tube. On the lower end of a rotary shaft are radial arms to which are fixed angularly disposed blades which serve to mix the shale and hot sand and deliver the residue to a central discharge pipe closed at the bottom by a conical valve which opens when the weight of the superimposed material is sufficient. The distillates are taken off by an outlet. Steam vapor or gas may be supplied to the retort, preferably through a hollow shaft leading to hollow stirrers perforated to permit of the gas passing into the material. The retort may be externally heated by hot gases in the space surrounding the retort, and the latter may be divided by horizontal floors so that the material is caused to funnel from the periphery to the center of the floor, then through a central opening on to the floor next below, and from the center to the periphery of this floor, and so on.

Importance of low-temperature distillation of coal for German fuel economics

Energy Technology Data Exchange (ETDEWEB)

Rosendahl, F

1942-01-01

Improved processes are available to give low-temperature distillation products economic importance. Low-temperature distillation is limited to the utilization of high-volatile nut coals and briquets. The coke formed can be used as a smokeless fuel, and the tar directly as a fuel oil. Phenols can be extracted, in order to work up the residue into fuel oil and motor fuel. Large deposits of coal in Upper Silesia and in the Saar District are suitable for low-temperature distillation.

Modeling of steam distillation mechanism during steam injection process using artificial intelligence.

Science.gov (United States)

Daryasafar, Amin; Ahadi, Arash; Kharrat, Riyaz

2014-01-01

Steam distillation as one of the important mechanisms has a great role in oil recovery in thermal methods and so it is important to simulate this process experimentally and theoretically. In this work, the simulation of steam distillation is performed on sixteen sets of crude oil data found in the literature. Artificial intelligence (AI) tools such as artificial neural network (ANN) and also adaptive neurofuzzy interference system (ANFIS) are used in this study as effective methods to simulate the distillate recoveries of these sets of data. Thirteen sets of data were used to train the models and three sets were used to test the models. The developed models are highly compatible with respect to input oil properties and can predict the distillate yield with minimum entry. For showing the performance of the proposed models, simulation of steam distillation is also done using modified Peng-Robinson equation of state. Comparison between the calculated distillates by ANFIS and neural network models and also equation of state-based method indicates that the errors of the ANFIS model for training data and test data sets are lower than those of other methods.

Modeling of Steam Distillation Mechanism during Steam Injection Process Using Artificial Intelligence

Science.gov (United States)

Ahadi, Arash; Kharrat, Riyaz

2014-01-01

Steam distillation as one of the important mechanisms has a great role in oil recovery in thermal methods and so it is important to simulate this process experimentally and theoretically. In this work, the simulation of steam distillation is performed on sixteen sets of crude oil data found in the literature. Artificial intelligence (AI) tools such as artificial neural network (ANN) and also adaptive neurofuzzy interference system (ANFIS) are used in this study as effective methods to simulate the distillate recoveries of these sets of data. Thirteen sets of data were used to train the models and three sets were used to test the models. The developed models are highly compatible with respect to input oil properties and can predict the distillate yield with minimum entry. For showing the performance of the proposed models, simulation of steam distillation is also done using modified Peng-Robinson equation of state. Comparison between the calculated distillates by ANFIS and neural network models and also equation of state-based method indicates that the errors of the ANFIS model for training data and test data sets are lower than those of other methods. PMID:24883365

Advances in chaos theory and intelligent control

CERN Document Server

Vaidyanathan, Sundarapandian

2016-01-01

The book reports on the latest advances in and applications of chaos theory and intelligent control. Written by eminent scientists and active researchers and using a clear, matter-of-fact style, it covers advanced theories, methods, and applications in a variety of research areas, and explains key concepts in modeling, analysis, and control of chaotic and hyperchaotic systems. Topics include fractional chaotic systems, chaos control, chaos synchronization, memristors, jerk circuits, chaotic systems with hidden attractors, mechanical and biological chaos, and circuit realization of chaotic systems. The book further covers fuzzy logic controllers, evolutionary algorithms, swarm intelligence, and petri nets among other topics. Not only does it provide the readers with chaos fundamentals and intelligent control-based algorithms; it also discusses key applications of chaos as well as multidisciplinary solutions developed via intelligent control. The book is a timely and comprehensive reference guide for graduate s...

Membrane/distillation hybrid process research and development. Final report, phase II

Energy Technology Data Exchange (ETDEWEB)

Mazanec, T.J.

1997-07-01

This report covers work conducted under the grant awarded to BP by DOE in late 1991 entitled {open_quotes}Membrane/Distillation Hybrid Process Research and Development.{close_quotes} The program was directed towards development and commercialization of the BP process for separation of vapor phase olefins from non-olefins via facilitated transport using an aqueous facilitator. The program has come to a very successful conclusion, with formation of a partnership between BP and Stone and Webster Engineering Corporation (SWEC) to market and commercialize the technology. The focus of this report is the final portion of the program, during which engineering re-design, facilitator optimization, economic analysis, and marketing have been the primary activities. At the end of Phase II BP was looking to partner with an engineering firm to advance the selective olefin recovery (SOR) technology from the lab/demo stage to full commercialization. In August 1995 BP and SWEC reached an agreement to advance the technology by completing additional Phase III work with DOE and beginning marketing activities.

Development of a Nonlinear Soft-Sensor Using a GMDH Network for a Refinery Crude Distillation Tower

Science.gov (United States)

Fujii, Kenzo; Yamamoto, Toru

In atmospheric distillation processes, the stabilization of processes is required in order to optimize the crude-oil composition that corresponds to product market conditions. However, the process control systems sometimes fall into unstable states in the case where unexpected disturbances are introduced, and these unusual phenomena have had an undesirable affect on certain products. Furthermore, a useful chemical engineering model has not yet been established for these phenomena. This remains a serious problem in the atmospheric distillation process. This paper describes a new modeling scheme to predict unusual phenomena in the atmospheric distillation process using the GMDH (Group Method of Data Handling) network which is one type of network model. According to the GMDH network, the model structure can be determined systematically. However, the least squares method has been commonly utilized in determining weight coefficients (model parameters). Estimation accuracy is not entirely expected, because the sum of squared errors between the measured values and estimates is evaluated. Therefore, instead of evaluating the sum of squared errors, the sum of absolute value of errors is introduced and the Levenberg-Marquardt method is employed in order to determine model parameters. The effectiveness of the proposed method is evaluated by the foaming prediction in the crude oil switching operation in the atmospheric distillation process.

27 CFR 27.1 - Imported distilled spirits, wines, and beer.

Science.gov (United States)

2010-04-01

..., wines, and beer. 27.1 Section 27.1 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS IMPORTATION OF DISTILLED SPIRITS, WINES, AND BEER Scope of Regulations § 27.1 Imported distilled spirits, wines, and beer. This part, “Importation of...

27 CFR 27.48 - Imported distilled spirits, wines, and beer.

Science.gov (United States)

2010-04-01

..., wines, and beer. 27.48 Section 27.48 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS IMPORTATION OF DISTILLED SPIRITS, WINES, AND BEER Tax On Imported Distilled Spirits, Wines, and Beer Collection of Internal Revenue Taxes § 27.48 Imported...

Distillation time effect on lavender essential oil yield and composition

Science.gov (United States)

Lavender (Lavandula angustifolia Mill.) is one of the most widely grown essential oil crops in the world. Commercial extraction of lavender oil is done using steam distillation. The objective of this study was to evaluate the effect of the length of the distillation time (DT) on lavender essential o...

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bennie, G

1875-11-12

For distilling shale, or other oil-yielding minerals, two or more, preferably four, vertical retorts are mounted in a brickwork oven and are heated in the first place by coal, coke or other fuel on a grate. The spent material from the retorts is discharged from one or more in turn on to the grate and is used, together with additional fuel if necessary, to maintain the heat of the retorts. The retorts are charged by means of hoppers and lids and are discharged by means of movable bottoms actuated by rods and levers acting in combination with outlet valves. The retorts are tapered from the bottom upwards.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Young, W; Brash, P

1866-05-04

In the distillation of oil from coal, shale, etc., hydrocarbon vapors which are condensed only with difficulty, and are of small value, are reheated and sent back into the retorts. A jet of steam, or a forcing or exhausting apparatus, may be used for this purpose, and the vapors are passed under false bottoms with which the retorts are preferably provided. In the rectification of the oils, a producer known as still bottoms results which, when redistilled, gives rise to vapors condensable only with difficulty. These vapors may be passed back into the still, or may be mixed and heated, in a separate vessel, with the vapors coming from the still.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Medlrum, E

1869-02-06

The invention relates to the decomposition of the liquids with high boiling points, and the solids with low melting points, left in the purification of paraffin oil obtained from coal or shale. The liquids or melted solids, or their vapors, are passed through a heated iron tube or retort and c., which may be packed with broken stones, spent shale, and c. The temperature is regulated between 700/sup 0/F and a low red heat. The condensed products consist of a mixture of light and heavy oils, which may be separated by distillation. The heavier residues may be again passed through the decomposing apparatus.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Dow, P

1884-09-11

The invention has for its object to regulate the temperature at any point of vertical retorts in which steam or steam and air are employed for the distillation of shale, coal, and other substances. Vertical steam pipes at the exterior of each retort and connected with main pipes have a series of branches at different levels and furnished with regulating-valves or cocks. The admission of air is similarly regulated and spy-holes with shutters blocked or sealed against the escape of such products by the fuel intake at one end of the conduit and the congested masses of coke discharged at the other.

Chemical and biological effects of heavy distillate recycle in the SRC-II process

Energy Technology Data Exchange (ETDEWEB)

Wilson, B.W.; Pelroy, R.A.; Anderson, R.P.; Freel, J.

1983-12-01

Recent work from the Merriam Laboratory continuous coal liquefaction units shows that heavy distillate from the SRC-II process can be recycled to extinction, and hence a distillate product boiling entirely below 310/sup 0/C (590/sup 0/F) (or other selected boiling points) is feasible. In these runs distillate yield was not reduced; gas make was unaffected; and hydrogen consumption was increased only slightly, in keeping with the generally higher hydrogen content of lighter end products. Total distillate yield (C/sub 5/-590/sup 0/F) was 56 wt %, MAF coal in runs with subbituminous coal from the Amax Belle Ayr mine. Product endpoint is well below 371/sup 0/C (700/sup 0/F), the temperature above which coal distillates appear to become genotoxic; and the product was shown to be free of mutagenic activity in the Ames test. Chemical analyses showed both the < 270/sup 0/C (< 518/sup 0/F) and the < 310/sup 0/C (< 590/sup 0/F) distillates to be essentially devoid of several reference polycyclic compounds known to be carcinogenic in laboratory animals. Tests for tumorigenic or carcinogenic activity were not carried out on these materials. However, a comparison of chemical data from the Merriam heavy distillate samples with data on the other SRC-II distillates where carcinogenesis or tumorigenesis data is available leads to the expectation that < 371/sup 0/C (< 700/sup 0/F) materials from the Merriam Laboratory will have greatly reduced tumorigenic and carcinogenic activity in skin painting tests. Other studies suggest the product should be more readily upgraded than full-range (C/sub 5/-900/sup 0/F) distillate.

Membrane distillation of industrial cooling tower blowdown water

Directory of Open Access Journals (Sweden)

N.E. Koeman-Stein

2016-06-01

Full Text Available The potential of membrane distillation for desalination of cooling tower blowdown water (CTBD is investigated. Technical feasibility is tested on laboratory and pilot scale using real cooling tower blowdown water from Dow Benelux in Terneuzen (Netherlands. Two types of membranes, polytetrafluorethylene and polyethylene showed good performance regarding distillate quality and fouling behavior. Concentrating CTBD by a factor 4.5 while maintaining a flux of around 2 l/m2*h was possible with a water recovery of 78% available for reuse. Higher concentration factors lead to severe decrease in flux which was caused by scaling. Membrane distillation could use the thermal energy that would otherwise be discharged of in a cooling tower and function as a heat exchanger. This reduces the need for cooling capacity and could lead to a total reduction of 37% water intake for make-up water, as well as reduced energy and chemicals demands and greenhouse gas emissions.

Distillation and Air Stripping Designs for the Lunar Surface

Science.gov (United States)

Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

2009-01-01

Air stripping and distillation are two different gravity-based methods, which may be applied to the purification of wastewater on the lunar base. These gravity-based solutions to water processing are robust physical separation techniques, which may be advantageous to many other techniques for their simplicity in design and operation. The two techniques can be used in conjunction with each other to obtain high purity water. The components and feed compositions for modeling waste water streams are presented in conjunction with the Aspen property system for traditional stage distillation models and air stripping models. While the individual components for each of the waste streams will vary naturally within certain bounds, an analog model for waste water processing is suggested based on typical concentration ranges for these components. Target purity levels for the for recycled water are determined for each individual component based on NASA s required maximum contaminant levels for potable water Distillation processes are modeled separately and in tandem with air stripping to demonstrate the potential effectiveness and utility of these methods in recycling wastewater on the Moon. Optimum parameters such as reflux ratio, feed stage location, and processing rates are determined with respect to the power consumption of the process. Multistage distillation is evaluated for components in wastewater to determine the minimum number of stages necessary for each of 65 components in humidity condensate and urine wastewater mixed streams. Components of the wastewater streams are ranked by Henry s Law Constant and the suitability of air stripping in the purification of wastewater in terms of component removal is evaluated. Scaling factors for distillation and air stripping columns are presented to account for the difference in the lunar gravitation environment. Commercially available distillation and air stripping units which are considered suitable for Exploration Life Support

Non-equilibrium modelling of distillation

NARCIS (Netherlands)

Wesselingh, JA; Darton, R

1997-01-01

There are nasty conceptual problems in the classical way of describing distillation columns via equilibrium stages, and efficiencies or HETP's. We can nowadays avoid these problems by simulating the behaviour of a complete column in one go using a non-equilibrium model. Such a model has phase

Toxicity of middle distillates from dermal exposure.

Science.gov (United States)

Koschier, F J

1999-02-01

This report focuses on recent studies that investigated the effects of kerosine dermal exposure on neurotoxicity and reproductive/developmental toxicity. Background toxicity information will also be reviewed for kerosine range mid distillates. The kerosine range mid distillates have a carbon range of C9-C16 and have a boiling range of 302-554 degrees F (150-290 degrees C). This category includes kerosine, aviation fuels (e.g., Jet A, JP-5 and JP-8), no. 1 fuel oil and diesel fuel oil. In general, the kerosine range mid distillates demonstrate relatively low acute toxicity by any route of exposure. High inhalation exposures can induce central nervous system depression characterized by ataxia, hypoactivity and prostration. Kerosines are known to cause skin irritation and inflammation under conditions of acute and repeated exposure in animals and humans, but are only slightly irritating to the eye and are not skin sensitizers. In addition, the absorption of kerosine range mid distillates through the skin has been demonstrated to be fairly rapid, but limited to approximately 10-15% of the applied dose after 24 hours. The kerosine range mid distillates are generally inactive in genetic toxicity tests although positive studies have been reported. Positive results, while at times equivocal, have been reported for straight run kerosine and jet fuel A in the mouse lymphoma assay with metabolic activation, and hydrodesulfurized kerosine (mouse) and jet fuel A (rat) in the bone marrow cytogenetic assay. Effects on the nervous and reproductive systems have been reported in humans and experimental animals under conditions where inhalation and dermal exposure to specific kerosine type fuels are sometimes difficult to separate. Recent laboratory studies have addressed this point and examined the effects of dermal exposure. In these studies, rats were exposed to hydrodesulfurized kerosine by skin application to determine the potential of dermal contact to cause reproductive

Characterization of corn stover, distiller grains and cattle manure for thermochemical conversion

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijun; Shahbazi, Abolghasem [Department of Natural Resources and Environmental Design, North Carolina Agricultural and Technical State University, Greensboro, NC 27411 (United States); Hanna, Milford A. [Industrial Agricultural Products Center, Department of Biological Systems Engineering, University of Nebraska-Lincoln, Lincoln, NE 68583-0726 (United States)

2011-01-15

Corn stover, distiller grains and cattle manure were characterized to evaluate their acceptability for thermochemical conversion. The energy densities of ground corn stover, distiller grains and cattle manure after totally drying were 3402, 11,813 and 10,374 MJ/m{sup 3}, compared to 37,125 MJ/m{sup 3} for coal. The contents of volatiles in corn stover, distiller grains and cattle manure were 77.4, 82.6 and 82.8%, respectively, on a dry and ash-free basis compared to 43.6% for coal. About 90% of the volatiles in corn stover, distiller grains and cattle manure were released at pyrolysis temperatures of 497, 573 and 565 C, respectively. The combustion of corn stover, distiller grains and cattle manure were completed at 620, 840 and 560 C, respectively. The heat values of the biomass and air mixture for stoichiometric combustion were 2.64, 2.75 and 1.77 MJ/kg for dried corn stover, distiller grains and cattle manure, respectively, as compared to 2.69 MJ/kg for coal. Combustion of 1 kg of dry corn stover, distiller grains and cattle manure generated 5.33, 6.20 and 5.66 Nm{sup 3} of flue gas, respectively, compared to 8.34 Nm{sup 3} for coal. Simulation showed that gasification of 1 kg of dried corn stover, distiller grains and cattle manure at 850 C and ER of 0.3 generated 2.02, 2.37 and 1.44 Nm{sup 3} dry syngas at a heating value of about 4.5 MJ/Nm{sup 3}, compared to 3.52 Nm{sup 3} at 5.8 MJ/Nm{sup 3} for coal. The molecular ratio of H{sub 2} to CO in the biomass-derived syngas was close to 1.0, compared to about 0.5 for the coal-derived syngas. (author)

77 FR 25382 - Proposed Amendment to the Standards of Identity for Distilled Spirits

Science.gov (United States)

2012-04-30

... set forth in Sec. 5.22(f) as follows: Class 6; rum. ``Rum'' is an alcoholic distillate from the..., produced at less than 190[deg] proof in such manner that the distillate possesses the taste, aroma and... mixtures solely of such distillates. The above standard does not currently provide for any subcategories or...

Determination of 129I using distillation method and liquid scintillation spectrometry

International Nuclear Information System (INIS)

Horvathova, B.; Dulanska, S.; Remenec, B.; Matel, L.; Gardonova, V.

2014-01-01

The conditions for effective distillation of iodine as a screening method for the determination of 129 I by liquid scintillation spectrometry were optimized. By distillation of iodine it is possible to achieve high-purity fraction without interferences needed for measuring 129 I for liquid scintillation spectrometer. Yields of separation were determined gravimetrically using PdI 2 ·H 2 O. The environment that was found to be effective for distillation of iodine is made up of 1 - 2 mol dm -3 HNO 3 together with 0.4 g of NaNO 2 as an oxidizing agent (I . →I 2 ). For testing of distillation, suitable apparatus for distillation of iodine was designed. The apparatus was connected to a vacuum box, which sucks iodine of the distilled solution. Then the iodine was captured in a solution of NaOH at a concentration of 1.5 mol dm -3 . As part of the optimization methodology, it was found that the concentration of NaOH solution for adsorption I 2 (g) does not have any influence on the yields, as opposed to its volume, where it is necessary to use a maximum amount of NaOH in the holding flask for maximum adsorption of iodine. It was determined, that time needed for coagulation PdI 2 ·H 2 O is 24 hours and suitable time for distillation was 20 minutes. Optimized method for the determination of 129 I was applied for various matrices from NPPs in Slovak Republic. Values of 129 I for all analyzed samples were less than the minimum detectable activity (0.043 Bq). The separation yields were in the range (73.14 to 82.04)% and 129 I was measured on a liquid scintillation spectrometer TRI CARB 2900TR with high detection efficiency of 95%. (authors)

Quick assessment of binary distillation efficiency using a heat engine perspective

International Nuclear Information System (INIS)

Blahušiak, M.; Kiss, A.A.; Kersten, S.R.A.; Schuur, B.

2016-01-01

With emphasis on close boiling, (near-)ideal VLE mixtures, this paper links the efficiency of distillation to the binary feed composition and thermal properties of the compounds. The proposed approach, treating the process as a heat engine, allows to directly quantify distillation performance (in terms of energy intensity & efficiency) based on the components boiling points and feed composition. In addition, this approach reviews and formulates simple, approximate and essentially non-iterative calculation procedures to quickly estimate the energy efficiency of distillation. These estimations may be applied to identify opportunities to save significant amounts of energy. The results show that the reboiler duty for low relative volatility is relatively independent of the heat of vaporization and feed composition, while being reciprocally proportional to the Carnot efficiency of the distillation column. The internal efficiency for distillation of mixtures with low relative volatility has a maximum of about 70% for a symmetrical feed (equimolar ratio) and decreases to zero for unsymmetrical feed compositions approaching infinite dilution. With increasing relative volatility, the maximum efficiency is preserved, but the locus shifts towards lower light component fractions. At very high relative volatility, the internal efficiency increases with decreasing concentration of light component, as typical for evaporators. - Highlights: • A heat engine perspective was applied to estimate binary distillation efficiency. • The method was derived from first principles. • Validation on industrial cases showed the strength of the method.

Extraction of Citrus Hystrix D.C. (Kaffir Lime) Essential Oil Using Automated Steam Distillation Process: Analysis of Volatile Compounds

International Nuclear Information System (INIS)

Nurhani Kasuan; Zuraida Muhammad; Zakiah Yusoff; Mohd Hezri Fazalul Rahiman; Mohd Nasir Taib; Zaibunnisa Abdul Haiyee

2013-01-01

An automated steam distillation was successfully used to extract volatiles from Citrus hystrix D.C (Kaffir lime) peels. The automated steam distillation integrated with robust temperature control can commercially produce large amount of essential oil with efficient heating system. Objective of this study is to quantify the oil production rate using automated steam distillation and analyze the composition of volatiles in Kaffir lime peels oil at different controlled and uncontrolled temperature conditions. From the experimentation, oil extraction from Kaffir lime peels only took approximately less than 3 hours with amount of oil yield was 13.4 % more than uncontrolled temperature. The identified major compounds from Kaffir lime peels oil were sabinene, β-pinene, limonene, α-pinene, camphene, myrcene, terpinen-4-ol, α-terpineol, linalool, terpinolene and citronellal which are considered to have good organoleptic quality. In contrast with uncontrolled temperature, oil analysis revealed that some important volatile compounds were absent such as terpinolene, linalool, terpinen-4-ol due to thermal degradation effect from fast heating of extracted material. (author)

Practical Implementations of Advanced Process Control for Linear Systems

DEFF Research Database (Denmark)

Knudsen, Jørgen K . H.; Huusom, Jakob Kjøbsted; Jørgensen, John Bagterp

2013-01-01

This paper describes some practical problems encountered, when implementing Advanced Process Control, APC, schemes on linear processes. The implemented APC controllers discussed will be LQR, Riccati MPC and Condensed MPC controllers illustrated by simulation of the Four Tank Process and a lineari......This paper describes some practical problems encountered, when implementing Advanced Process Control, APC, schemes on linear processes. The implemented APC controllers discussed will be LQR, Riccati MPC and Condensed MPC controllers illustrated by simulation of the Four Tank Process...... on pilot plant equipment on the department of Chemical Engineering DTU Lyngby....

Overview of advanced process control in welding within ERDA

International Nuclear Information System (INIS)

Armstrong, R.E.

1977-01-01

The special kinds of demands placed on ERDA weapons and reactors require them to have very reliable welds. Process control is critical in achieving this reliability. ERDA has a number of advanced process control projects underway with much of the emphasis being on electron beam welding. These include projects on voltage measurement, beam-current control, beam focusing, beam spot tracking, spike suppression, and computer control. A general discussion of process control in welding is followed by specific examples of some of the advanced joining process control projects in ERDA

Comparative ileal amino acid digestibility of distillers' grains for growing pigs.

Science.gov (United States)

Adeola, Olayiwola; Ragland, Darryl

2016-12-01

The objective of the experiment reported here was to investigate and compare the amino acid (AA) digestibility of distillers' dried grains (DDG), distillers' dried grains with solubles (DDGS), high protein distillers' dried grains (HP-DDG), and high protein distillers' dried grains with solubles (HP-DDGS) in growing pigs. Five semi-purified diets consisting of DDG, DDGS, HP-DDG, HP-DDGS, and nitrogen-free diet (NFD) were fed to pigs fitted with simple T-cannula for 5 observations per diet. Endogenous losses of AA at the terminal ileum of pigs that received the NFD were used to calculate standardized ileal digestibility (SID) of AA from apparent ileal digestibility (AID) of AA. The AID of Lys in DDGS was lower ( P  digestibility, there was no difference between DDG and DDGS in the SID of the indispensable AA. The SID of Lys in DDG was greater ( P  digestibility values for traditional and high-protein corn distillers' dried grains coproducts for use in formulating swine diets. Amino acid digestibility was generally higher in HP-DDG than in other tested co-products of the dry grind processing of corn for ethanol.

Purification of specific structured lipids by distillation: Effects on acyl migration

DEFF Research Database (Denmark)

Xu, Xuebing; Skands, A.; Adler-Nissen, Jens

2001-01-01

The cause and effects of acyl migration during the purification of specific structured lipids by distillation were studied in a conventional batch deodorizer with stripping steam. The mixture of specific structured lipids produced by lipase-catalyzed acidolysis between rapeseed oil and capric acid...... influenced the rate of acyl migration, and their combinations made the effect more severe. However, diacylglycerols were found to be the main reason for acyl migration. In the distillation of the specific structured lipid product mixture, distillation temperature and time were the main factors to determine...... the degree of acyl migration and the extent of separation of free fatty acids. The results indicate that more efficient separation technology should be used to improve the quality of the purified structured lipids. in order to reduce the distillation temperature, vacuum should be made as low as possible...

Entrainer-based reactive distillation versus conventional reactive distillation for the synthesis of fatty acid esters

NARCIS (Netherlands)

Jong, de M.C.; Dimian, A.C.; Haan, de A.B.

2008-01-01

In this paper different reactive distillation configurations for the synthesis of isopropyl myristate were compared with the use of process models made in Aspen Plus. It can be concluded that the configurations in which an entrainer is added are more capable to reach the required conversion of

Mathematical modeling of alcohol distillation columns

Directory of Open Access Journals (Sweden)

Ones Osney Pérez

2011-04-01

Full Text Available New evaluation modules are proposed to extend the scope of a modular simulator oriented to the sugar cane industry, called STA 4.0, in a way that it can be used to carry out x calculation and analysis in ethanol distilleries. Calculation modules were developed for the simulation of the columns that are combined in the distillation area. Mathematical models were supported on materials and energy balances, equilibrium relations and thermodynamic properties of the ethanol-water system. Ponchon-Savarit method was used for the evaluation of the theoretical stages in the columns. A comparison between the results using Ponchon- Savarit method and those obtained applying McCabe-Thiele method was done for a distillation column. These calculation modules for ethanol distilleries were applied to a real case for validation.

The relationship between locus of control and career advancement

OpenAIRE

2014-01-01

M.Com. (Industrial Psychology) The objective which career of this study advancement is was to investigate the extent to contingent on the personality construct locus of control. In order to achieve this, empirical research was conducted in a South African organisation. A survey questionnaire measuring career advancement and locus of control was completed by 152 subjects. The hypothesis which was formulated was that people with higher rates of career advancement would be more internal and t...

An Automatic Approach to the Stabilization Condition in a HIx Distillation Simulation

International Nuclear Information System (INIS)

Chang, Ji Woon; Shin, Young Joon; Lee, Ki Young; Kim, Yong Wan; Chang, Jong Hwa; Youn, Cheung

2010-01-01

In the Sulfur-Iodine(SI) thermochemical process to produce nuclear hydrogen, an H 2 O-HI-I 2 ternary mixture solution discharged from the Bunsen reaction is primarily concentrated by electro-electrodialysis. The concentrated solution is distillated in the HIx distillation column to generate a high purity HI vapor. The pure HI vapor is obtained at the top of the HIx distillation column and the diluted HIx solution is discharged at the bottom of the column. In order to simulate the steady-state HIx distillation column, a vapor-liquid equilibrium (VLE) model of the H 2 O-HI-I 2 ternary system is required and the subprogram to calculate VLE concentrations has been already introduced by KAERI research group in 2006. The steady state simulation code for the HIx distillation process was also developed in 2007. However, the intrinsic phenomena of the VLE data such as the steep slope of a T-x-y diagram caused the instability of the simulation calculation. In this paper, a computer program to automatically find a stabilization condition in the steady state simulation of the HIx distillation column is introduced. A graphic user interface (GUI) function to monitor an approach to the stabilization condition was added in this program

Continuous distillation of bituminous shale. [hot gas in chamber and chamber heated externally

Energy Technology Data Exchange (ETDEWEB)

1921-04-27

A process of continuous distillation of bituminous shale is given in which the heat necessary is produced not only on the exterior but also in the interior of the distillation apparatus in the form of hot gas directly bathing the shale. The residual carbon in the shale after distillation, or maybe with other fuel added to it, can be utilized; the fuel may be utilized not only for the heat it furnishes but also for the gas it gives and which adds itself to the incondensable gas from the distillation. The temperature of the zone of distillation of the shale is regulated by the quantity of gas, the temperature of this gas (which can be lowered voluntarily by injecting into the air a certain quantity of water vapor), the length of the zone comprised between the zone of gasification and distillation; the injection of water vapor permits the recovery of part of the nitrogen of the shale in the form of ammonia; the materials are withdrawn continuously in a mechanical way.

Advanced control room caters for the operator

International Nuclear Information System (INIS)

George, C.R.; Rygg, D.E.

1980-01-01

In existing control rooms the operators' efficiency is often limited by widely scattered and sometimes illogically arranged controls which tend to increase the potential for outages or equipment damage. The advanced control room described allows instant and ready access to preselected information and control by one or two operators from a seated or standing position. (author)

Tissue free water tritium separation from foodstuffs by azeotropic distillation

International Nuclear Information System (INIS)

Constantin, F.; Ciubotaru, A.; Popa, D.

1998-01-01

In this paper the tritium separation from tissue free water in foodstuffs by azeotropic distillation is described. Tritium in tissue water is assayed by liquid scintillation counting using well-established quenched correction method. The mean value of the tritium concentration in tissue water from foodstuffs is about 6-12 Bq/l very similar to the tritium mean concentration measured in the surface waters of the area where the samples have been collected (about 12 Bq/l. Therefore, the tritium content in the water fraction of the food samples can be considered in equilibrium with the local environmental water sources. The azeotropic distillation it is an accessible separation method which does not need a sophisticated and expansive distillation apparatus. It is a fast method of separation tissue free water from foodstuffs being very important in the surveillance activity of the environmental within nuclear electric plant. It is suitable for processing a small quantity of samples and for a production type facility when a large number of samples must be processed because the solvent can be purified and reused. The azeotropic distillation has some limits being used to separate water from samples with high content of water (85-90%) and simple a simple chemical structures as: vegetables, fruits, cereal, soil, vegetation. According to the results obtained, the organic substituents of milk, wine, meat (casein, lactose, milk fat, alcohol, esters) may enhance the chemisorption of tritium on through exchange organic hydrogen as -OH, -SH, -NH, -COOH with tritium. Also, the tissue water separation by azeotropic distillation is not complete and can not guarantee the absence of the vaporization isotope effect of the HTO/H 2 O system., However, the azeotropic distillation is the preferred method of the water extraction from food samples, which makes it useful for the tritium transfer from soil to foodstuffs. (authors)

Tissue free water tritium separation from foodstuffs by azeotropic distillation

Energy Technology Data Exchange (ETDEWEB)

Constantin, F; Ciubotaru, A; Popa, D [Inspectorate of Public Health of Bucharest (Romania)

1999-12-31

In this paper the tritium separation from tissue free water in foodstuffs by azeotropic distillation is described. Tritium in tissue water is assayed by liquid scintillation counting using well-established quenched correction method. The mean value of the tritium concentration in tissue water from foodstuffs is about 6-12 Bq/l very similar to the tritium mean concentration measured in the surface waters of the area where the samples have been collected (about 12 Bq/l. Therefore, the tritium content in the water fraction of the food samples can be considered in equilibrium with the local environmental water sources. The azeotropic distillation it is an accessible separation method which does not need a sophisticated and expansive distillation apparatus. It is a fast method of separation tissue free water from foodstuffs being very important in the surveillance activity of the environmental within nuclear electric plant. It is suitable for processing a small quantity of samples and for a production type facility when a large number of samples must be processed because the solvent can be purified and reused. The azeotropic distillation has some limits being used to separate water from samples with high content of water (85-90%) and simple a simple chemical structures as: vegetables, fruits, cereal, soil, vegetation. According to the results obtained, the organic substituents of milk, wine, meat (casein, lactose, milk fat, alcohol, esters) may enhance the chemisorption of tritium on through exchange organic hydrogen as -OH, -SH, -NH, -COOH with tritium. Also, the tissue water separation by azeotropic distillation is not complete and can not guarantee the absence of the vaporization isotope effect of the HTO/H{sub 2}O system., However, the azeotropic distillation is the preferred method of the water extraction from food samples, which makes it useful for the tritium transfer from soil to foodstuffs. (authors) 2 tabs.

The Design and Manufacturing of Essential oil Distillation Plant for ...

African Journals Online (AJOL)

Choice-Academy

industry in the country do not have the capacity to manufacture the complete distillation plant system with the required precision for standard quality of oil at affordable cost. Thus, the design and the experiment in the use of a prototype small size distillation unit showed that the technology is appropriate for essential oil ...

Control system design specification of advanced spent fuel management process units

Energy Technology Data Exchange (ETDEWEB)

Ahn, S. H.; Kim, S. H.; Yoon, J. S

2003-06-01

In this study, the design specifications of instrumentation and control system for advanced spent fuel management process units are presented. The advanced spent fuel management process consists of several process units such as slitting device, dry pulverizing/mixing device, metallizer, etc. In this study, the control and operation characteristics of the advanced spent fuel management mockup process devices and the process devices developed in 2001 and 2002 are analysed. Also, a integral processing system of the unit process control signals is proposed, which the operation efficiency is improved. And a redundant PLC control system is constructed which the reliability is improved. A control scheme is proposed for the time delayed systems compensating the control performance degradation caused by time delay. The control system design specification is presented for the advanced spent fuel management process units. This design specifications can be effectively used for the detail design of the advanced spent fuel management process.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Young, W; Neilson, A; Young, A

1876-10-09

The invention relates to modifications of the retort apparatus, described in Specification No. 2487, A.D. 1872, for the destructive distillation of shale and other bituminous substances. The retorts instead of being worked continuously are completely filled and completely discharged in turn. They are made oblong in cross-section in order to present the material in thin layers and cause it to be acted upon more rapidly and economically. The retorts can thus be heated solely by the combustion of the carbonaceus matter contained in the discharged residues or with a small amount of coal in addition. Each retort is contracted at the bottom and is fitted with a box or chest having a hole in it corresponding to the opening in the retort and a sliding plate of iron, firebrick, or other suitable material, which can be operated by a rod passing through the front of the box, for opening or closing the retort. Underneath the box and over the combustion chamber are placed fireclay blocks leaving an opening, which can be closed by another plate of firebrick or the like. When distillation commences, the gases and vapors in the retort are drawn off through a pipe and a main by an exhauster. In order to prevent air from entering the retort or hydrocarbon vapor from being puffed back by the action of the wind, the gas which remains after the condensation of the oils is forced back into the box between the plates and part of it enters the retort and part the combustion chamber. In order to avoid the liability of the oil being carried past the condensers by the action of the gas, steam may be used as a substitute for the gas or mixed with it in large proportions, a steam jet being used to force the gas into the main supplying the boxes.

Sequential Elution of Essential Oil Constituents during Steam Distillation of Hops (Humulus lupulus L.) and Influence on Oil Yield and Antimicrobial Activity.

Science.gov (United States)

Jeliazkova, Ekaterina; Zheljazkov, Valtcho D; Kačániova, Miroslava; Astatkie, Tess; Tekwani, Babu L

2018-06-07

The profile and bioactivity of hops (Humulus lupulus L.) essential oil, a complex natural product extracted from cones via steam distillation, depends on genetic and environmental factors, and may also depend on extraction process. We hypothesized that compound mixtures eluted sequentially and captured at different timeframes during the steam distillation process of whole hop cones would have differential chemical and bioactivity profiles. The essential oil was collected sequentially at 8 distillation time (DT) intervals: 0-2, 2-5, 5-10, 10-30, 30-60, 60-120, 120-180, and 180-240 min. The control was a 4-h non-interrupted distillation. Nonlinear regression models described the DT and essential oil compounds relationship. Fractions yielded 0.035 to 0.313% essential oil, while control yielded 1.47%. The oil eluted during the first hour was 83.2%, 9.6% during the second hour, and only 7.2% during the second half of the distillation. Essential oil (EO) fractions had different chemical profile. Monoterpenes were eluted early, while sequiterpenes were eluted late. Myrcene and linalool were the highest in 0-2 min fraction, β-caryophyllene, β-copaene, β-farnesene, and α-humulene were highest in fractions from middle of distillation, whereas α- bergamotene, γ-muurolene, β- and α-selinene, γ- and δ-cadinene, caryophyllene oxide, humulne epoxide II, τ-cadinol, and 6-pentadecen-2-one were highest in 120-180 or 180-240 min fractions. The Gram-negative Escherichia coli was strongly inhibited by essential oil fractions from 2-5 min and 10-30 min, followed by oil fraction from 0-2 min. The strongest inhibition activity against Gram-negative Yersinia enterocolitica, and Gram-positive Clostridium perfringens, Enterococcus faecalis, and Staphylococcus aureus subs. aureus was observed with the control essential oil. This is the first study to describe significant activity of hops essential oils against Trypanosoma brucei, a parasitic protozoan that causes African

Project T.E.A.M. (Technical Education Advancement Modules). Advanced Statistical Process Control.

Science.gov (United States)

Dunlap, Dale

This instructional guide, one of a series developed by the Technical Education Advancement Modules (TEAM) project, is a 20-hour advanced statistical process control (SPC) and quality improvement course designed to develop the following competencies: (1) understanding quality systems; (2) knowing the process; (3) solving quality problems; and (4)…

Advanced Control Facility for the CERN-UNICOS Framework

CERN Document Server

Pezzetti, M; Coppier, H

2010-01-01

CERN, during last decade, has extensively applied the CERN/UNICOS framework to large scale cryoplant control system. An increase of interested to advanced control techniques and innovative simulation environment applied to cryogenic processes has also occur. Since new control algorithm development into UNICOS framework requires significant time, a control testing platform which can be externally connected can improve and simplify the procedure of testing advanced controllers implementation. In this context, the present paper describes the development of a control testing tool at CERN, which allows rapid control strategies implementation through the Matlab/Simulink® environment, coupled with the large scale cryogenics UNICOS control system or with the CERN PROCOS simulation environment. The time delays which are inherently introduced by network links and communication protocols are analyzed and experimentally identified. Security and reliability issues are also discussed.

Advanced control of a water supply system : A case study

NARCIS (Netherlands)

Bakker, M.; Rajewicz, T.; Kien, H.; Vreeburg, J.H.G.; Rietveld, L.C.

2013-01-01

WTP Gruszczyn supplies drinking water to a part of the city of Pozna?, in the Midwest of Poland. The conventional production flow control and pressure control of the facility was replaced by the advanced control software called OPIR. To assess the differences between conventional and advanced

Advances in robust fractional control

CERN Document Server

Padula, Fabrizio

2015-01-01

This monograph presents design methodologies for (robust) fractional control systems. It shows the reader how to take advantage of the superior flexibility of fractional control systems compared with integer-order systems in achieving more challenging control requirements. There is a high degree of current interest in fractional systems and fractional control arising from both academia and industry and readers from both milieux are catered to in the text. Different design approaches having in common a trade-off between robustness and performance of the control system are considered explicitly. The text generalizes methodologies, techniques and theoretical results that have been successfully applied in classical (integer) control to the fractional case. The first part of Advances in Robust Fractional Control is the more industrially-oriented. It focuses on the design of fractional controllers for integer processes. In particular, it considers fractional-order proportional-integral-derivative controllers, becau...

Optimizing design parameter for light isotopes separation by distillation method

International Nuclear Information System (INIS)

Ahmadi, M.

1999-01-01

More than methods are suggested in the world for producing heavy water, where between them chemical isotopic methods, distillation and electro lys are used widely in industrial scale. To select suitable method for heavy water production in Iran, taking into consideration, domestic technology an facilities, combination of hydrogen sulphide-water dual temperature process (Gs) and distillation (D W) may be proposed. Natural water, is firstly enriched up to 15 a% by G S process and then by distillation unit is enriched up to the grade necessary for Candu type reactors (99.8 a%). The aim of present thesis, is to achieve know-how, optimization of design parameters, and executing basic design for water isotopes separation using distillation process in a plant having minimum scale possible. In distillation, vapour phase resulted from liquid phase heating, is evidently composed of the same constituents as liquid phase. In isotopic distillation, the difference in composition of constituents is not considerable. In fact alteration of constituents composition is so small that makes the separation process impossible, however, direct separation and production of pure products without further processing which becomes possible by distillation, makes this process as one of the most important separation processes. Profiting distillation process to produce heavy water is based on difference existing between boiling point of heavy and light water. The trends of boiling points differences (heavy and light water) is adversely dependant with pressure. As the whole system pressure decreases, difference in boiling points increases. On the other hand according to the definition, separation factor is equal to the ratio of pure light water vapour pressure to that of heavy water, or we can say that the trend of whole system pressure decrease results in separation factor increase, which accordingly separation factor equation to pressure variable should be computed firstly. According to the

Distillation and Visualization of Spatiotemporal Structures in Turbulent Flow Fields

International Nuclear Information System (INIS)

Hege, Hans-Christian; Hotz, Ingrid; Kasten, Jens

2011-01-01

Although turbulence suggests randomness and disorder, organized motions that cause spatiotemporal 'coherent structures' are of particular interest. Revealing such structures in numerically given turbulent or semi-turbulent flows is of interest both for practically working engineers and theoretically oriented physicists. However, as long as there is no common agreement about the mathematical definition of coherent structures, extracting such structures is a vaguely defined task. Instead of searching for a general definition, the data visualization community takes a pragmatic approach and provides various tool chains implemented in flexible software frameworks that allow the user to extract distinct flow field structures. Thus physicists or engineers can select those flow structures which might advance their insight best. We present different approaches to distill important features from turbulent flows and discuss the necessary steps to be taken on the example of Lagrangian coherent structures.

Characterization and differentiation of monovarietal grape pomace distillate from native varieties of Galicia.

Science.gov (United States)

López-Vázquez, Cristina; Bollaín, María Herminia; Moser, Sergio; Orriols, Ignacio

2010-09-08

Monovarietal grape pomace distillates (orujo) of six native varieties of Vitis vinifera L. from Galicia (Albarino, Treixadura, Godello, Loureira, Dona Branca, and Torrontes) have been thoroughly analyzed considering esters, alcohols, major aldehydes, monoterpenes, sesquiterpenes, norisoprenoids, and diterpenes. Albarino and Loureira distillates showed similar profiles of terpenic compounds, with the Loureira products having higher contents of monoterpenols. Native Torrontes distillate from Galicia is principally characterized by marked levels of some sesquiterpenes such as cadinene isomers and epizonarene. On the other hand, Treixadura, Godello, and Dona Branca grape pomace distillates seem not to have any marked terpenic content, and their single separation is difficult. PCA data treatments showed a good separation among the terpenic-rich varieties. Also, the p-menthen-9-al isomers, typical flavors in honey citrus and dill herb (derived from 8-hydroxylinalool), are reported for the first time in grape pomace distillate.

Reactive distillation: an attractive alternative for the synthesis of unsaturated polyester

NARCIS (Netherlands)

Shah, M.R.; Zondervan, E.; Oudshoorn, M.L.; Haan, de A.B.

2011-01-01

Unsaturated polyester is traditionally produced in a batch wise operating reaction vessel connected to a distillation unit. An attractive alternative for the synthesis of unsaturated polyester is a reactive distillation. To value such alternative synthesis route reliable process models need to be

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Craig, A

1863-11-12

To obtain hydrocarbons, coal, shale, or other bituminous substance is distilled in an annular retort. The outer surface is heated by an arrangement of furnaces and flues, and the inner surface has a number of small openings through which the evolved hydrocarbons pass. The inner chamber is cooled by cold air or water pipes to condense the hydrocarbon which is then run off to purifying-apparatus. In a modification, the retort is heated from the inside, the hydrocarbon being condensed in an outer case. Another form of retort consists of a narrow flat chamber, heated from one side and with a cooled condensing-chamber on the other; or two retorts may be used, with one condensing-chamber between them.

Advanced nonlinear engine speed control systems

DEFF Research Database (Denmark)

Vesterholm, Thomas; Hendricks, Elbert

1994-01-01

Several subsidiary control problems have turned out to be important for improving driveability and fuel consumption in modern spark ignition (SI) engine cars. Among these are idle speed control and cruise control. In this paper the idle speed and cruise control problems will be treated as one......: accurately tracking of a desired engine speed in the presence of model uncertainties and severe load disturbances. This is accomplished by using advanced nonlinear control techniques such as input/output-linearization and sliding mode control. These techniques take advantage of a nonlinear model...... of the engine dynamics, a mean value engine model....

Rotary drum for distilling bituminous material

Energy Technology Data Exchange (ETDEWEB)

1921-11-02

A rotary drum with insert tubes for distilling bituminous materials, like mineral coal, brown coal, wood, peat, and oil-shale, is characterized in that the insert tube is heated also by superheated steam introduced into the drum.

Advanced gray rod control assembly

Science.gov (United States)

Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

2013-09-17

An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

Modeling of Steam Distillation Mechanism during Steam Injection Process Using Artificial Intelligence

Directory of Open Access Journals (Sweden)

Amin Daryasafar

2014-01-01

neurofuzzy interference system (ANFIS are used in this study as effective methods to simulate the distillate recoveries of these sets of data. Thirteen sets of data were used to train the models and three sets were used to test the models. The developed models are highly compatible with respect to input oil properties and can predict the distillate yield with minimum entry. For showing the performance of the proposed models, simulation of steam distillation is also done using modified Peng-Robinson equation of state. Comparison between the calculated distillates by ANFIS and neural network models and also equation of state-based method indicates that the errors of the ANFIS model for training data and test data sets are lower than those of other methods.

Entrainer selection for the synthesis of fatty acid esters by entrainer-based reactive distillation

NARCIS (Netherlands)

Jong, de M.C.; Zondervan, E.; Dimian, A.C.; Haan, de A.B.

2010-01-01

In this research it is demonstrated that, due to the similarities between Entrainer-based Reactive Distillation and azeotropic distillation, the same selection rules can be applied to select a suitable entrainer. From a list of suitable entrainers for the azeotropic distillation of isopropanol and

Green and brown propolis: efficient natural biocides for the control of bacterial contamination of alcoholic fermentation of distilled beverage

Directory of Open Access Journals (Sweden)

Márcia Justino Rossini Mutton

2014-12-01

Full Text Available This study aimed to evaluate the efficiency of natural biocides, brown and green propolis, for the control of bacterial contamination in the production of sugarcane spirit. The treatments consisted of brown and green propolis extracts, ampicillin, and a control and were assessed at the beginning and end of harvest season in ten fermentation cycles. In the microbiological analyses, the lactic acid bacteria were quantified in the inoculum before and after the treatment with biocides, and the viability of yeast cells during fermentation was evaluated. The levels of acids, glycerol, total residual reducing sugars, and ethanol were analyzed for the wine resulting from each fermentation cycle. A reduction in the number of bacterial contaminants in the inoculum in the treatments with the natural biocides was observed, but it did not affect the viability of yeast cells. The control of the contaminants led to the production of higher levels of ethanol and reduced acidity in the wine produced. The results of the use of brown and green propolis to control the growth microorganisms in the fermentation of sugarcane spirit can be of great importance for using alternative strategies to synthetic antibacterials in fermentation processes including other distilled beverage or spirits.

Quality Evaluation of Agricultural Distillates Using an Electronic Nose

OpenAIRE

Dymerski, Tomasz; Gębicki, Jacek; Wardencki, Waldemar; Namieśnik, Jacek

2013-01-01

The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing ...

Ervaringen met Advanced Cruise Control (ACC) in een korte praktijkproef.

NARCIS (Netherlands)

Oei, H.-l.

2003-01-01

Experiences with Advanced Cruise Control in traffic; a limited experiment. Advanced Cruise Control (ACC) is an ordinary cruise control in which the desired speed is installed manually, but in which the headway time to the vehicle in front is also taken into account. If the headway time becomes less

Research and development on the application of advanced control technologies to advanced nuclear reactor systems: A US national perspective

International Nuclear Information System (INIS)

White, J.D.; Monson, L.R.; Carrol, D.G.; Dayal, Y.

1989-01-01

Control system designs for nuclear power plants are becoming more advanced through the use of digital technology and automation. This evolution is taking place because of: (1) the limitations in analog based control system performance and maintenance and availability and (2) the promise of significant improvement in plant operation and availability due to advances in digital and other control technologies. Digital retrofits of control systems in US nuclear plants are occurring now. Designs of control and protection systems for advanced LWRs are based on digital technology. The use of small inexpensive, fast, large-capacity computers in these designs is the first step of an evolutionary process described in this paper. Under the sponsorship of the US Department of Energy (DOE), Oak Ridge National Laboratory, Argonne National Laboratory, GE Nuclear Energy and several universities are performing research and development in the application of advances in control theory, software engineering, advanced computer architectures, artificial intelligence, and man-machine interface analysis to control system design. The target plant concept for the work described in this paper is the Power Reactor Inherently Safe Module reactor (PRISM), an advanced modular liquid metal reactor concept. This and other reactor designs which provide strong passive responses to operational upsets or accidents afford good opportunities to apply these advances in control technology. 18 refs., 5 figs

Development of High Throughput Salt Separation System with Integrated Liquid Salt Separation - Salt Distillation Assembly

Energy Technology Data Exchange (ETDEWEB)

Kwon, Sangwoon; Park, K. M.; Kim, J. G.; Jeong, J. H.; Lee, S. J.; Park, S. B.; Kim, S. S.

2013-01-15

The capacity of a salt distiller should be sufficiently large to reach the throughput of uranium electro-refining process. In this study, an assembly composing a liquid separation sieve and a distillation crucible was developed for the sequential operation of a liquid salt separation and a vacuum distillation in the same tower. The feasibility of the sequential salt separation was examined by the rotation test of the sieve-crucible assembly and sequential operation of a liquid salt separation and a vacuum distillation. The adhered salt in the uranium deposits was removed successfully. The salt content in the deposits was below 0.1 wt% after the sequential operation of the liquid salt separation - salt distillation. From the results of this study, it could be concluded that efficient salt separation can be realized by the sequential operation of liquid salt separation and vacuum distillation in one distillation tower since the operation procedures are simplified and no extra operation of cooling and reheating is necessary.

Distillation, destructive: gas retorts