WorldWideScience

Sample records for advanced control strategies

  1. Economic Benefits of Advanced Control Strategies in Biological Nutrient Removal Systems

    DEFF Research Database (Denmark)

    Carstensen, J.; Nielsen, M.K.; Harremoës, Poul

    1994-01-01

    Advances in on-line monitoring of nutrient salt concentrations and computer technology has created a large potential for the implementation of advanced and complex control strategies in biological nutrient removal systems. The majority of wastewater treatment plants today are operated with very...

  2. Advanced Control Strategy for Single-Phase Voltage-Source Active Rectifier with Low Harmonic Emission

    Science.gov (United States)

    Blahník, Vojtĕch; Peroutka, Zdenĕk; Talla, Jakub

    2014-03-01

    This paper introduces the advanced control of single-phase voltage-source active rectifier. This control provide direct control of trolley-wire current and active damping of low-frequency disturbances at the converter ac side. Our proposed control strategy combines PR controller with feed-forward model and low-frequency harmonic compensator based on resonant controllers. Achieved experimental results show excellent converter behavior, where converter is fed by strongly distorted supply voltage.

  3. Advanced Control Strategy of DFIG Wind Turbines for Power System Fault Ride Through

    DEFF Research Database (Denmark)

    Yang, Lihui; Xu, Zhao; Ostergaard, Jacob;

    2012-01-01

    This paper presents an advanced control strategy for the rotor and grid side converters of the doubly fed induction generator (DFIG) based wind turbine (WT) to enhance the low-voltage ride-through (LVRT) capability according to the grid connection requirement. Within the new control strategy, the...... instantaneous DC-link current of the rotor side converter in order to smooth the DC-link voltage fluctuations during the grid fault. A major difference from other methods is that the proposed control strategy can absorb the additional kinetic energy during the fault conditions, and significantly reduce the...... oscillations in the stator and rotor currents and the DC bus voltage. The effectiveness of the proposed control strategy has been demonstrated through various simulation cases. Compared with conventional crowbar protection, the proposed control method can not only improve the LVRT capability of the DFIG WT...

  4. Energy savings and economics of advanced control strategies for packaged air conditioners with gas heat

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weimin; Katipamula, Srinivas; Huang, Yunzhi; Brambley, Michael R.

    2013-10-01

    This paper presents an evaluation of the potential energy savings from adding advanced control to existing packaged air conditioners. Advanced control options include air-side economizer, multi-speed fan control, demand control ventilation and staged cooling. The energy and cost savings from the different control strategies individually and in combination are estimated using the EnergyPlus detailed energy simulation program for four building types, namely, a small office building, a stand-alone retail building, a strip mall building and a supermarket building. For each of the four building types, the simulation was run for 16 locations covering all 15 climate zones in the U.S. The maximum installed cost of a replacement controller that provides acceptable payback periods to owners is estimated.

  5. Operational Strategy of CBPs for load balancing of Operators in Advanced Main Control Room

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seunghwan; Kim, Yochan; Jung, Wondea [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    With the using of a computer-based control room in an APR1400 (Advanced Pressurized Reactor-1400), the operators' behaviors in the main control room had changed. However, though the working environment of operators has been changed a great deal, digitalized interfaces can also change the cognitive tasks or activities of operators. First, a shift supervisor (SS) can confirm/check the conduction of the procedures and the execution of actions of board operators (BOs) while confirming directly the operation variables without relying on the BOs. Second, all operators added to their work the use of a new CBP and Soft Controls, increasing their procedural workload. New operational control strategies of CBPs are necessary for load balancing of operator's task load in APR1400. In this paper, we compared the workloads of operators in an APR1400 who work with two different usages of the CBP. They are SS oriented usage and SS-BO collaborative usage. In this research, we evaluated the workloads of operators in an advanced main control room by the COCOA method. Two types of CBP usages were defined and the effects of these usages on the workloads were investigated. The obtained results showed that the workloads between operators in a control room can be balanced according to the CBP usages by assigning control authority to the operators.

  6. Energy Savings and Economics of Advanced Control Strategies for Packaged Air-Conditioning Units with Gas Heat

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weimin; Katipamula, Srinivas; Huang, Yunzhi; Brambley, Michael R.

    2011-12-31

    Pacific Northwest National Laboratory (PNNL) with funding from the U.S. Department of Energy's Building Technologies Program (BTP) evaluated a number of control strategies that can be implemented in a controller, to improve the operational efficiency of the packaged air conditioning units. The two primary objectives of this research project are: (1) determine the magnitude of energy savings achievable by retrofitting existing packaged air conditioning units with advanced control strategies not ordinarily used for packaged units and (2) estimating what the installed cost of a replacement control with the desired features should be in various regions of the U.S. This document reports results of the study.

  7. Strategies for the control of parametric instability in advanced gravitational wave detectors

    Energy Technology Data Exchange (ETDEWEB)

    Ju, L; Blair, D G; Zhao, C; Gras, S; Zhang, Z; Barriga, P; Miao, H; Fan, Y; Merrill, L, E-mail: juli@physics.uwa.edu.a [School of Physics, University of Western Australia, 35 Stirling Highway, Crawley, Perth, WA 6009 (Australia)

    2009-01-07

    Parametric instabilities have been predicted to occur in all advanced high optical power gravitational wave detectors. In this paper we review the problem of parametric instabilities, summarize the latest findings and assess various schemes proposed for their control. We show that non-resonant passive damping of test masses reduces parametric instability but has a noise penalty, and fails to suppress the Q-factor of many modes. Resonant passive damping is shown to have significant advantages but requires detailed modeling. An optical feedback mode suppression interferometer is proposed which is capable of suppressing all instabilities but requires experimental development.

  8. Advanced control strategies to integrate German offshore wind potential into electrical energy sypply

    Energy Technology Data Exchange (ETDEWEB)

    Rohrig, K.; Schloegl, F.; Jursa, R.; Wolff, M. [Institut fuer Solare Energieversorgungstechnik (ISET), Kassel (Germany); Fischer, F.; Hartge, S. [ENERCON GmbH, Aurich (Germany); Valov, B.; Heier, S. [Kassel Univ. (Gesamthochschule) (Germany)

    2005-07-01

    The paper describes the technical status and presents new concepts, models and approaches for the technical assistance of large scale wind power integration into the electrical energy supply system in Germany. It shows the technical and economic problems with the integration of high penetration of wind power plant in the network and the total electrical system. After an analysis of the effects of increased wind power generation on system planning and grid operation, we discuss innovative operational control concepts for large (offshore) wind farms. These concepts will provide a multitude of new possibilities to enable simple, flexible and undisturbed reaction to the demands of participants (wind farm operators, grid operators). These operational control strategies are mainly based on ISETs successful employed wind power prediction tools, operated by all German TSO's, and will enable energy and power control, as well as the provision of reactive power, in order to achieve comparable properties to conventional power plant types. (orig.)

  9. Overview of Modelling and Advanced Control Strategies for Wind Turbine Systems

    Directory of Open Access Journals (Sweden)

    Silvio Simani

    2015-11-01

    Full Text Available The motivation for this paper comes from a real need to have an overview of the challenges of modelling and control for very demanding systems, such as wind turbine systems, which require reliability, availability, maintainability, and safety over power conversion efficiency. These issues have begun to stimulate research and development in the wide control community particularly for these installations that need a high degree of “sustainability”. Note that this represents a key point for offshore wind turbines, since they are characterised by expensive and/or safety critical maintenance work. In this case, a clear conflict exists between ensuring a high degree of availability and reducing maintenance times, which affect the final energy cost. On the other hand, wind turbines have highly nonlinear dynamics, with a stochastic and uncontrollable driving force as input in the form of wind speed, thus representing an interesting challenge also from the modelling point of view. Suitable control methods can provide a sustainable optimisation of the energy conversion efficiency over wider than normally expected working conditions. Moreover, a proper mathematical description of the wind turbine system should be able to capture the complete behaviour of the process under monitoring, thus providing an important impact on the control design itself. In this way, the control scheme could guarantee prescribed performance, whilst also giving a degree of “tolerance” to possible deviation of characteristic properties or system parameters from standard conditions, if properly included in the wind turbine model itself. The most important developments in advanced controllers for wind turbines are also briefly referenced, and open problems in the areas of modelling of wind turbines are finally outlined.

  10. DOE Project: Optimization of Advanced Diesel Engine Combustion Strategies "University Research in Advanced Combustion and Emissions Control" Office of FreedomCAR and Vehicle Technologies Program

    Energy Technology Data Exchange (ETDEWEB)

    Reitz, Rolf; Foster, D.; Ghandhi, J.; Rothamer, D.; Rutland, C.; Sanders, S.; Trujillo, M.

    2012-10-26

    The goal of the present technology development was to increase the efficiency of internal combustion engines while minimizing the energy penalty of meeting emissions regulations. This objective was achieved through experimentation and the development of advanced combustion regimes and emission control strategies, coupled with advanced petroleum and non-petroleum fuel formulations. To meet the goals of the project, it was necessary to improve the efficiency of expansion work extraction, and this required optimized combustion phasing and minimized in-cylinder heat transfer losses. To minimize fuel used for diesel particulate filter (DPF) regeneration, soot emissions were also minimized. Because of the complex nature of optimizing production engines for real-world variations in fuels, temperatures and pressures, the project applied high-fidelity computing and high-resolution engine experiments synergistically to create and apply advanced tools (i.e., fast, accurate predictive models) developed for low-emission, fuel-efficient engine designs. The companion experiments were conducted using representative single- and multi-cylinder automotive and truck diesel engines.

  11. Advanced Control Strategies to Enable a More Wide-Scale Adoption of Single-Phase Photovoltaic Systems

    DEFF Research Database (Denmark)

    Yang, Yongheng

    The installations of PhotoVoltaic (PV) systems, including grid-connected PV systems, have experienced a significant increase in the past few decades. More PV capacity is expected for the future power grid to be of intelligence and flexibility. This thriving scenario also raises concerns about...... the availability, quality and reliability of the whole power grid. Consequently, grid codes/standards are continuously being revised to host more PV energy in the grid. Ancillary services required initially by wind power systems, e.g. fault ride-through and grid support, are becoming more preferable in PV systems...... today than they were. In addition, achieving high efficiency and high reliability is always of importance for PV systems in order to reduce the cost of energy. Both goals can be enabled by advanced control strategies for PV systems, which are typically based on power electronics technology. In the light...

  12. Advanced Control Strategy of Back-to-Back PWM Converters in PMSG Wind Power System

    Directory of Open Access Journals (Sweden)

    Tan Luong Van

    2015-01-01

    Full Text Available This paper proposes a control scheme of back-to-back PWM converters for the permanent magnet synchronous generator (PMSG wind turbine system. The DC-link voltage can be controlled at the machine-side converter (MSC, while the grid-side converter (GSC controls the grid active power for a maximum power point tracking (MPPT. At the grid fault condition, the DC-link voltage controller is designed using a feedback linearization (FL theory. For the MPPT, a proportional control loop is added to the torque control to reduce the influence of the inertia moment in the wind turbines, which can improve its dynamic performance. The validity of this control algorithm has been verified by the simulation of the 2-MW PMSG wind turbine system.

  13. Advanced Outage and Control Center: Strategies for Nuclear Plant Outage Work Status Capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Gregory Weatherby

    2012-05-01

    The research effort is a part of the Light Water Reactor Sustainability (LWRS) Program. LWRS is a research and development program sponsored by the Department of Energy, performed in close collaboration with industry to provide the technical foundations for licensing and managing the long-term, safe and economical operation of current nuclear power plants. The LWRS Program serves to help the US nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. The Outage Control Center (OCC) Pilot Project was directed at carrying out the applied research for development and pilot of technology designed to enhance safe outage and maintenance operations, improve human performance and reliability, increase overall operational efficiency, and improve plant status control. Plant outage management is a high priority concern for the nuclear industry from cost and safety perspectives. Unfortunately, many of the underlying technologies supporting outage control are the same as those used in the 1980’s. They depend heavily upon large teams of staff, multiple work and coordination locations, and manual administrative actions that require large amounts of paper. Previous work in human reliability analysis suggests that many repetitive tasks, including paper work tasks, may have a failure rate of 1.0E-3 or higher (Gertman, 1996). With between 10,000 and 45,000 subtasks being performed during an outage (Gomes, 1996), the opportunity for human error of some consequence is a realistic concern. Although a number of factors exist that can make these errors recoverable, reducing and effectively coordinating the sheer number of tasks to be performed, particularly those that are error prone, has the potential to enhance outage efficiency and safety. Additionally, outage management requires precise coordination of work groups that do not always share similar objectives. Outage

  14. Advanced power converters for universal and flexible power management in future electricity network -  Report on Control Strategies

    DEFF Research Database (Denmark)

    Ciobotaru, Mihai; Iov, Florin; Zanchetta, Pericle;

    is also given with a special focus on Phase Locked Loop systems. The response of the single and three phase PLLs is analyzed under different grid events. Four control strategies are studied in the WP5, namely: synchronous reference frame control, predictive control stationary reference frame control......The present document summarizes the work that has been done in Work Package 5 (WP5) where the focus is on modelling and control of the Uniflex-PM system. The models used in the WP5 are described in detail. Since the grid synchronization and monitoring techniques play an important role...... in the control of the Uniflex-PM system, a special attention is paid to this topic. The events in the electrical networks are treated in detail in terms of definitions and classifications from standards, origins, and surveys in different countries. A summary of the grid synchronization and monitoring methods...

  15. Advanced Control Engineering

    DEFF Research Database (Denmark)

    Zhou, Jianjun

    1999-01-01

    This book is developed as a textbook for the course Advanced Control Engineering. The book is intended for students in mechanical engineering and its aim is to provide an understanding of modern control theory as well as methodologies and applications for state space modeling and design...

  16. Design and simulation of an automation system of a production process and fractionation of 131I, using strategies of advanced control

    International Nuclear Information System (INIS)

    In this report, the results are obtained in the design and simulation of a control system using advanced strategies in a production cell in the Plant Production of Radioisotopes of IPEN. The results demonstrate that the temperature of the coalition oven is stabilized after 30 minutes, being constituted in an advantage to obtain the maximum yield of the cell production of 131I; also, an integral good controller has been designed that allows to obtain a mathematical model that reproduces with enough accuracy the behavior of the process. With the final simulation it has been to demonstrate that the System Control of Temperature of the Cell Production of 131I is a controllable system and allows to carry out the respective sequence with other variables of control of the production cell. (author)

  17. Advanced AC Motor Control

    Energy Technology Data Exchange (ETDEWEB)

    Kazmierkowski, M.P. [Institute of Control and Industrial Electronics, Warsaw University of Technology, Warszawa (Poland)

    1997-12-31

    In this paper a review of control methods for high performance PWM inverter-fed induction motor drives is presented. Starting from the description of an induction motor by the help of the space vectors, three basic control strategic are discussed. As first, the most popular Field Oriented Control (FOC) is described. Secondly, the Direct Torque and Flux vector Control (DTFC) method, which - in contrast to FOC - depart from idea of coordinate transformation and analogy with DC motor, is briefly characterized. The last group is based on Feedback Linearization Control (FLC) and can be easy combined with sliding mode control. The simulation and experimental oscillograms that illustrate the performance of the discussed control strategies are shown. (orig.) 35 refs.

  18. Elevator Control Strategies

    OpenAIRE

    Ceder, Frederick; Nordin, Alexandra

    2013-01-01

    This paper investigates the efficiency of known elevator control strategies by simulating these in an own made apartment simulator. Efficiency will be determined by the lowest product of the energy consumption (Watt/second), average waiting time, average transfer time and the maximum waiting time of a passenger, which is the output by the simulator. The apartment simulator will simulate the elevator behavior, according to a respective control strategy, and the passenger flow on each respectiv...

  19. Advanced Wavefront Control Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Olivier, S S; Brase, J M; Avicola, K; Thompson, C A; Kartz, M W; Winters, S; Hartley, R; Wihelmsen, J; Dowla, F V; Carrano, C J; Bauman, B J; Pennington, D M; Lande, D; Sawvel, R M; Silva, D A; Cooke, J B; Brown, C G

    2001-02-21

    this project, work was performed in four areas (1) advanced modeling tools for deformable mirrors (2) low-order wavefront correctors with Alvarez lenses, (3) a direct phase measuring heterdyne wavefront sensor, and (4) high-spatial-frequency wavefront control using spatial light modulators.

  20. Advanced Emissions Control Development Program

    Energy Technology Data Exchange (ETDEWEB)

    A.P.Evans; K.E. Redinger; M.J. Holmes

    1998-04-01

    The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

  1. Advanced Emissions Control Development Program: Mercury Control

    International Nuclear Information System (INIS)

    McDermott Technology, Inc. (a subsidiary of Babcock ampersand Wilcox) is conducting the Advanced Emissions Control Development Project (AECDP) which is aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPS) from coal-fired electric utility plants. The need for such controls may arise as the US Environmental Protection Agency (EPA) proceeds with implementation of requirements set forth in the Clean Air Act Amendments (CAAA's) of 1990. Promulgation of air toxics emissions regulations for electric utility plants could dramatically impact utilities burning coal, their industrial and residential customers, and the coal industry. AECDP project work will supply the information needed by utilities to respond to potential HAPs regulations in a timely, cost-effective, enviromnentally-sound manner which supports the continued use of the Nation's abundant reserves of coal, such as those in the State of Ohio. The development work is being carried out using the 10 MW Clean Environment Development Facility wherein air toxics emissions control strategies can be developed under controlled conditions. The specific objectives of the project are to (1) measure and understand production and partitioning of air toxics species for a variety of coals, (2) optimize the air toxics removal performance of conventional flue gas cleanup systems, (3) develop advanced air toxics emissions control concepts, (4) develop and validate air toxics emissions measurement and monitoring techniques, and (5) establish a comprehensive, self-consistent air toxics data library. This project is supported by the Department of Energy, the Ohio Coal Development Office within the Ohio Department of Development and Babcock ampersand Wilcox. A comprehensive assessment of HAP emissions from coal-fired electric utility boilers sponsored by the Department of Energy and the Electric Power Research Institute concluded that with the exception of

  2. Tax Strategy Control

    DEFF Research Database (Denmark)

    Rossing, Christian Plesner

    2013-01-01

    environment. Moreover, the paper extends existing contingency-based theory on MCS by illustrating the role of inter-organisational network collaboration across MNE transfer pricing tax experts. This collaboration, caused by a widely dispersed tax knowledge base, fuels the formal interactive control system......This paper examines how a functional tax strategy impacts the management control system (MCS) in a multinational enterprise (MNE) facing transfer pricing tax risks. Based on case study findings it is argued that the MCS in a multinational setting is contingent upon the MNE's response to its tax...... and reduces tax uncertainty. The paper adopts an interdisciplinary approach for explaining findings, using contingency-based theory and network theory at the inter-organisational level....

  3. Advanced Control of Turbofan Engines

    CERN Document Server

    Richter, Hanz

    2012-01-01

    Advanced Control of Turbofan Engines describes the operational performance requirements of turbofan (commercial)engines from a controls systems perspective, covering industry-standard methods and research-edge advances. This book allows the reader to design controllers and produce realistic simulations using public-domain software like CMAPSS: Commercial Modular Aero-Propulsion System Simulation, whose versions are released to the public by NASA. The scope of the book is centered on the design of thrust controllers for both steady flight and transient maneuvers. Classical control theory is not dwelled on, but instead an introduction to general undergraduate control techniques is provided. This book also: Develops a thorough understanding of the challenges associated with engine operability from a control systems perspective, describing performance demands and operational constraints into the framework and language of modern control theory Presents solid theoretical support for classical and advanced engine co...

  4. Problems and Strategies in Applications of Advanced Process Control in China%中国过程先进控制工程应用中的若干问题与对策

    Institute of Scientific and Technical Information of China (English)

    罗雄麟; 左信

    2005-01-01

    Advanced Process Control (APC) is necessary for oil refining and chemical process in China, but some problems have emerged in the application of APC techniques in this field. This paper discusses the conditions of APC application concerning process design, distributed control system (DCS) choice and regular control. It analyzes the problems and strategies in APC application. Some suggestions are proposed for the enterprise to benefit from APC application.

  5. ADVANCED SULFUR CONTROL CONCEPTS

    Energy Technology Data Exchange (ETDEWEB)

    Apostolos A. Nikolopoulos; Santosh K. Gangwal; William J. McMichael; Jeffrey W. Portzer

    2003-01-01

    Conventional sulfur removal in integrated gasification combined cycle (IGCC) power plants involves numerous steps: COS (carbonyl sulfide) hydrolysis, amine scrubbing/regeneration, Claus process, and tail-gas treatment. Advanced sulfur removal in IGCC systems involves typically the use of zinc oxide-based sorbents. The sulfides sorbent is regenerated using dilute air to produce a dilute SO{sub 2} (sulfur dioxide) tail gas. Under previous contracts the highly effective first generation Direct Sulfur Recovery Process (DSRP) for catalytic reduction of this SO{sub 2} tail gas to elemental sulfur was developed. This process is currently undergoing field-testing. In this project, advanced concepts were evaluated to reduce the number of unit operations in sulfur removal and recovery. Substantial effort was directed towards developing sorbents that could be directly regenerated to elemental sulfur in an Advanced Hot Gas Process (AHGP). Development of this process has been described in detail in Appendices A-F. RTI began the development of the Single-step Sulfur Recovery Process (SSRP) to eliminate the use of sorbents and multiple reactors in sulfur removal and recovery. This process showed promising preliminary results and thus further process development of AHGP was abandoned in favor of SSRP. The SSRP is a direct Claus process that consists of injecting SO{sub 2} directly into the quenched coal gas from a coal gasifier, and reacting the H{sub 2}S-SO{sub 2} mixture over a selective catalyst to both remove and recover sulfur in a single step. The process is conducted at gasifier pressure and 125 to 160 C. The proposed commercial embodiment of the SSRP involves a liquid phase of molten sulfur with dispersed catalyst in a slurry bubble-column reactor (SBCR).

  6. Natural Gas for Advanced Dual-Fuel Combustion Strategies

    Science.gov (United States)

    Walker, Nicholas Ryan

    Natural gas fuels represent the next evolution of low-carbon energy feedstocks powering human activity worldwide. The internal combustion engine, the energy conversion device widely used by society for more than one century, is capable of utilizing advanced combustion strategies in pursuit of ultra-high efficiency and ultra-low emissions. Yet many emerging advanced combustion strategies depend upon traditional petroleum-based fuels for their operation. In this research the use of natural gas, namely methane, is applied to both conventional and advanced dual-fuel combustion strategies. In the first part of this work both computational and experimental studies are undertaken to examine the viability of utilizing methane as the premixed low reactivity fuel in reactivity controlled compression ignition, a leading advanced dual-fuel combustion strategy. As a result, methane is shown to be capable of significantly extending the load limits for dual-fuel reactivity controlled compression ignition in both light- and heavy-duty engines. In the second part of this work heavy-duty single-cylinder engine experiments are performed to research the performance of both conventional dual-fuel (diesel pilot ignition) and advanced dual-fuel (reactivity controlled compression ignition) combustion strategies using methane as the premixed low reactivity fuel. Both strategies are strongly influenced by equivalence ratio; diesel pilot ignition offers best performance at higher equivalence ratios and higher premixed methane ratios, whereas reactivity controlled compression ignition offers superior performance at lower equivalence ratios and lower premixed methane ratios. In the third part of this work experiments are performed in order to determine the dominant mode of heat release for both dual-fuel combustion strategies. By studying the dual-fuel homogeneous charge compression ignition and single-fuel spark ignition, strategies representative of autoignition and flame propagation

  7. National Drug Control Strategy, 2011

    Science.gov (United States)

    Office of National Drug Control Policy, 2011

    2011-01-01

    In May of 2010, President Obama released the Administration's inaugural "National Drug Control Strategy". Based on the premise that drug use and its consequences pose a threat not just to public safety, but also to public health, the 2010 "Strategy" represented the first comprehensive rebalancing of Federal drug control policy in the nearly 40…

  8. Advances in robust fractional control

    CERN Document Server

    Padula, Fabrizio

    2015-01-01

    This monograph presents design methodologies for (robust) fractional control systems. It shows the reader how to take advantage of the superior flexibility of fractional control systems compared with integer-order systems in achieving more challenging control requirements. There is a high degree of current interest in fractional systems and fractional control arising from both academia and industry and readers from both milieux are catered to in the text. Different design approaches having in common a trade-off between robustness and performance of the control system are considered explicitly. The text generalizes methodologies, techniques and theoretical results that have been successfully applied in classical (integer) control to the fractional case. The first part of Advances in Robust Fractional Control is the more industrially-oriented. It focuses on the design of fractional controllers for integer processes. In particular, it considers fractional-order proportional-integral-derivative controllers, becau...

  9. Advanced Strategies for Articular Cartilage Defect Repair

    Directory of Open Access Journals (Sweden)

    Fergal J. O'Brien

    2013-02-01

    Full Text Available Articular cartilage is a unique tissue owing to its ability to withstand repetitive compressive stress throughout an individual’s lifetime. However, its major limitation is the inability to heal even the most minor injuries. There still remains an inherent lack of strategies that stimulate hyaline-like articular cartilage growth with appropriate functional properties. Recent scientific advances in tissue engineering have made significant steps towards development of constructs for articular cartilage repair. In particular, research has shown the potential of biomaterial physico-chemical properties significantly influencing the proliferation, differentiation and matrix deposition by progenitor cells. Accordingly, this highlights the potential of using such properties to direct the lineage towards which such cells follow. Moreover, the use of soluble growth factors to enhance the bioactivity and regenerative capacity of biomaterials has recently been adopted by researchers in the field of tissue engineering. In addition, gene therapy is a growing area that has found noteworthy use in tissue engineering partly due to the potential to overcome some drawbacks associated with current growth factor delivery systems. In this context, such advanced strategies in biomaterial science, cell-based and growth factor-based therapies that have been employed in the restoration and repair of damaged articular cartilage will be the focus of this review article.

  10. Strategies for Industrial Multivariable Control

    DEFF Research Database (Denmark)

    Hangstrup, M.

    Multivariable control strategies well-suited for industrial applications are suggested. The strategies combine the practical advantages of conventional SISO control schemes and -technology with the potential of multivariable controllers. Special emphasis is put on parameter-varying systems whose...... dynamics and gains strongly depend upon one or more physical parameters characterizing the operating point. This class covers many industrial systems such as airplanes, ships, robots and process control systems. Power plant boilers are representatives for process control systems in general. The dynamics...... and gains of power plant boilers strongly depend upon the load (instantaneous power production). This non-linear behavior suggests the use of gain-scheduling. For parameter-varying systems the multivariable control strategies can hence be divided into the following subsequent steps: choice of architecture...

  11. Advanced Thermal Control Flight Experiment.

    Science.gov (United States)

    Kirkpatrick, J. P.; Brennan, P. J.

    1973-01-01

    The advanced Thermal Control Flight Experiment on the Applications Technology Satellite (ATS-F) will evaluate, for the first time in a space environment, the performance of a feedback-controlled variable conductance heat pipe and a heat pipe thermal diode. In addition, the temperature control aspects of a phase-change material (PCM) will be demonstrated. The methanol/stainless steel feedback-controlled heat pipe uses helium control gas that is stored in a wicked reservoir. This reservoir is electrically heated through a solid state controller that senses the temperature of the heat source directly. The ammonia/stainless steel diode heat pipe uses excess liquid to block heat transfer in the reverse direction. The PCM is octadecane. Design tradeoffs, fabrication problems, and performance during qualification and flight acceptance tests are discussed.

  12. Advanced strategies in liposomal cancer therapy

    DEFF Research Database (Denmark)

    Andresen, Thomas Lars; Jensen, Simon Skøde; Jørgensen, Kent

    2005-01-01

    Tumor specific drug delivery has become increasingly interesting in cancer therapy, as the use of chemotherapeutics is often limited due to severe side effects. Conventional drug delivery systems have shown low efficiency and a continuous search for more advanced drug delivery principles...... of this paper, we review our own work, exploiting secretory phospholipase A(2) as a site-specific trigger and prodrug activator in cancer therapy. We present novel prodrug lipids together with biophysical investigations of liposome systems, constituted by these new lipids and demonstrate their degradability...... is therefore of great importance. In the first part of this review, we present current strategies in the drug delivery field, focusing on site-specific triggered drug release from liposomes in cancerous tissue. Currently marketed drug delivery systems lack the ability to actively release the carried drug...

  13. Advanced gray rod control assembly

    Science.gov (United States)

    Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

    2013-09-17

    An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

  14. Advanced Control of Electrochromic Windows

    OpenAIRE

    Scartezzini, Jean-Louis; Zarkadis, Nikos; Morel, Nicolas

    2013-01-01

    In our research we use the technology of electrochromic (EC) glazing to maximize the use of daylight and minimize the energy consumption in buildings while preserving visual and thermal comfort of the users. We propose an advanced automatic control of EC windows coupled with an anidolic daylighting system (ADS), blinds and dimmable fluorescent lights. EC windows with a visible transmittance range (Tv) of 0.15 – 0.50 were installed on the southern façade of an office room of the LESO experimen...

  15. SPARTINA CONTROL STRATEGY OF CHINA

    Institute of Scientific and Technical Information of China (English)

    TAN Fang-Lin

    2007-01-01

    Spartina is a kind of very important and invasive grass. In its native range, it is very important for erosion control, fish, wildlife, and estuary reclamation. Therefore, it was introduced to many countries. Since 1963, it was introduced to China. Up to now, it was intentionally or accidentally planted nearly all estuaries in the east coast of China and the area was estimated over 0.1 × 106 hm2. As other introduced plants, Spartina grows very vigorously in China,and this caused many environmental and economical problems. So, it is an emergency to develop a Spartina control strategy of China. In the paper, the history of Spartina introduction in China was reviewed, and several methods which were probably feasible for China to control Spartina were introduced, including physical/mechanical (such as mowing, digging, and dredging), chemical, and biological methods. Before taking any measurments to control Spartina, 2 things should be done. The first was to develop a plan and make an inventory; the second was to select a feasible method according to local climatic, economic, social, and ecological conditions. It was suggested that it would be very important to assess the possible effect of control methods on the environment in order to prevent from causing other environmental problems.KEY WORDS :Spartina; control method; control strategy; environmental assessment

  16. Control strategy of shortcut nitrification

    Institute of Scientific and Technical Information of China (English)

    LU Gang; ZHENG Ping; JIN Ren-cun; QAISAR Mahmood

    2006-01-01

    Shortcut nitrification for ammonium-rich wastewater is energy-saving and cost-effective procedure that has become one of the hotspots in the field of biological denitrogenation. An orthogonal experiment was performed to study the combined effects of operational parameters on the performance of internal-loop airlift bioreactor for shortcut nitrification. The optimum operational parameters for the shortcut nitrification were found as temperature 35 ℃, pH 8.0, dissolved oxygen concentration 1.0 mg/L, ammonium concentration 4 mmol/L and HRT 16 h, which have different influence on the performance of shortcut nitrification reactor. The pH, temperature and dissolved oxygen concentration have significant bearing on the process. The results showed that the shortcut nitrification reactor could be successfully started up within 42 d, and the reactor performance is steady with minimum NO2-/NOx- of 85.2% , maximum 93.4% and average value of 91.4% in effluent. Based on the analysis of experimental data, a new control strategy named "priority + combination" for shortcut nitrification was suggested. Through this strategy, the startup and operation of shortcut nitrification for ammonium-rich sludge digester liquids were optimized. The control strategy works well to keep the reactor operation in steady state and in achieving high-efficiency for shortcut nitrification.

  17. Advanced Teaching Strategies of College English Vocabulary

    Institute of Scientific and Technical Information of China (English)

    谭萍

    2016-01-01

    Vocabulary teaching is an important part in English teaching, which purpose is to foster students to use learned words to conduct language communication, increasing the capability of language using in daily life. This paper analyzes the present condition and exposes the problems existing in English vocabulary teaching and learning, then, puts forward some scientific, effective strategies for the education of English vocabulary. I hope these teaching strategies can help teachers improve their teaching methods and help English learners acquire knowledge easily and efficiently.

  18. Advanced Control of Photovoltaic and Wind Turbines Power Systems

    DEFF Research Database (Denmark)

    Yang, Yongheng; Chen, Wenjie; Blaabjerg, Frede

    2014-01-01

    and wind renewables. Thus, in this chapter, advanced control strategies, which can enable the power conversion efficiently and reliably, for both photovoltaic (PV) and wind turbines power systems are addressed in order to enhance the integration of those technologies. Related grid demands have been...... presented firstly, where much more attention has been paid on specific requirements, like Low Voltage Ride-Through (LVRT) and reactive power injection capability. To perform the functions of those systems, advanced control strategies are presented with much more emphasis on the LVRT operation with reactive...... power injection for both single-phase and three-phase systems. Other control strategies like constant power generation control for PV systems to further increase the penetration level, and the improvements of LVRT performance for a doubly fed induction generator based wind turbine system by means...

  19. Innovation in Active Vibration Control Strategy of Intelligent Structures

    Directory of Open Access Journals (Sweden)

    A. Moutsopoulou

    2014-01-01

    Full Text Available Large amplitudes and attenuating vibration periods result in fatigue, instability, and poor structural performance. In light of past approaches in this field, this paper intends to discuss some innovative approaches in vibration control of intelligent structures, particularly in the case of structures with embedded piezoelectric materials. Control strategies are presented, such as the linear quadratic control theory, as well as more advanced theories, such as robust control theory. The paper presents sufficiently a recognizable advance in knowledge of active vibration control in intelligent structures.

  20. An Investigation of Pronunciation Learning Strategies of Advanced EFL Learners

    Science.gov (United States)

    Hismanoglu, Murat

    2012-01-01

    This paper aims at investigating the kinds of strategies deployed by advanced EFL learners at English Language Teaching Department to learn or improve English pronunciation and revealing whether there are any significant differences between the strategies of successful pronunciation learners and those of unsuccessful pronunciation learners. After…

  1. ADVANCED COMPRESSOR ENGINE CONTROLS TO ENHANCE OPERATION, RELIABILITY AND INTEGRITY

    Energy Technology Data Exchange (ETDEWEB)

    Gary D. Bourn; Jess W. Gingrich; Jack A. Smith

    2004-03-01

    This document is the final report for the ''Advanced Compressor Engine Controls to Enhance Operation, Reliability, and Integrity'' project. SwRI conducted this project for DOE in conjunction with Cooper Compression, under DOE contract number DE-FC26-03NT41859. This report addresses an investigation of engine controls for integral compressor engines and the development of control strategies that implement closed-loop NOX emissions feedback.

  2. Advanced Engineering Strategies for Periodontal Complex Regeneration

    Directory of Open Access Journals (Sweden)

    Chan Ho Park

    2016-01-01

    Full Text Available The regeneration and integration of multiple tissue types is critical for efforts to restore the function of musculoskeletal complex. In particular, the neogenesis of periodontal constructs for systematic tooth-supporting functions is a current challenge due to micron-scaled tissue compartmentalization, oblique/perpendicular orientations of fibrous connective tissues to the tooth root surface and the orchestration of multiple regenerated tissues. Although there have been various biological and biochemical achievements, periodontal tissue regeneration remains limited and unpredictable. The purpose of this paper is to discuss current advanced engineering approaches for periodontal complex formations; computer-designed, customized scaffolding architectures; cell sheet technology-based multi-phasic approaches; and patient-specific constructs using bioresorbable polymeric material and 3-D printing technology for clinical application. The review covers various advanced technologies for periodontal complex regeneration and state-of-the-art therapeutic avenues in periodontal tissue engineering.

  3. Control strategies for aircraft airframe noise reduction

    Institute of Scientific and Technical Information of China (English)

    Li Yong; Wang Xunnian; Zhang Dejiu

    2013-01-01

    With the development of low-noise aircraft engine,airframe noise now represents a major noise source during the commercial aircraft's approach to landing phase.Noise control efforts have therefore been extensively focused on the airframe noise problems in order to further reduce aircraft overall noise.In this review,various control methods explored in the last decades for noise reduction on airframe components including high-lift devices and landing gears are summarized.We introduce recent major achievements in airframe noise reduction with passive control methods such as fairings,deceleration plates,splitter plates,acoustic liners,slat cove cover and side-edge replacements,and then discuss the potential and control mechanism of some promising active flow control strategies for airframe noise reduction,such as plasma technique and air blowing/suction devices.Based on the knowledge gained throughout the extensively noise control testing,a few design concepts on the landing gear,high-lift devices and whole aircraft are provided for advanced aircraft low-noise design.Finally,discussions and suggestions are given for future research on airframe noise reduction.

  4. Innovation in Active Vibration Control Strategy of Intelligent Structures

    OpenAIRE

    A. Moutsopoulou; G. E. Stavroulakis; Pouliezos, A.

    2013-01-01

    Large amplitudes and attenuating vibration periods result in fatigue, instability, and poor structural performance. In light of past approaches in this field, this paper intends to discuss some innovative approaches in vibration control of intelligent structures, particularly in the case of structures with embedded piezoelectric materials. Control strategies are presented, such as the linear quadratic control theory, as well as more advanced theories, such as robust control theory. The paper ...

  5. Perfect 800 Advanced Strategies for Top Students

    CERN Document Server

    Celenti, Dan

    2010-01-01

    Getting into the nation's most competitive universities requires more than a good SAT score, it requires a perfect score. Perfect 800: SAT Math gives advanced students the tools needed to master the SAT math test. Covering areas including arithmetic concepts; algebra; geometry; and additional topics such as probability and weighted average, the book offers exposure to a wide range of degrees of difficulty in a holistic approach that allows students to experience the "real thing," including the impact of time constraints on their performance. By emphasizing critical thinking and analytic skills

  6. Advanced Emissions Control Development Program: Phase III

    Energy Technology Data Exchange (ETDEWEB)

    G.T. Amrhein; R.T. Bailey; W. Downs; M.J. Holmes; G.A. Kudlac; D.A. Madden

    1999-07-01

    The primary objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. The project goal is to effectively control air toxic emissions through the use of conventional flue gas clean-up equipment such as electrostatic precipitators (ESPs), fabric filters (baghouses - BH), and wet flue gas desulfurization systems (WFGD). Development work concentrated on the capture of trace metals, fine particulate, hydrogen chloride and hydrogen fluoride, with an emphasis on the control of mercury. The AECDP project is jointly funded by the US Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (OCDO), and Babcock and Wilcox, a McDermott company (B and W). This report discusses results of all three phases of the AECDP project with an emphasis on Phase III activities. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on characterization of the emissions of mercury and other air toxics and the control of these emissions for typical operating conditions of conventional flue gas clean-up equipment. Some general comments that can be made about the control of air toxics while burning a high-sulfur bituminous coal are as follows: (1) particulate control devices such as ESP's and baghouses do a good job of removing non-volatile trace metals, (2) particulate control devices (ESPs and baghouses) effectively remove the particulate-phase mercury, but the particulate-phase mercury was only a small fraction of the total for the coals tested, (3) wet scrubbing can effectively remove hydrogen chloride and hydrogen fluoride, and (4) wet scrubbers show good potential for the removal of mercury when operated under certain conditions, however, for certain applications, system enhancements can be required to achieve

  7. Radioprotective Agents: Strategies and Translational Advances.

    Science.gov (United States)

    Kamran, Mohammad Zahid; Ranjan, Atul; Kaur, Navrinder; Sur, Souvik; Tandon, Vibha

    2016-04-01

    Radioprotectors are agents required to protect biological system exposed to radiation, either naturally or through radiation leakage, and they protect normal cells from radiation injury in cancer patients undergoing radiotherapy. It is imperative to study radioprotectors and their mechanism of action comprehensively, looking at their potential therapeutic applications. This review intimately chronicles the rich intellectual, pharmacological story of natural and synthetic radioprotectors. A continuous effort is going on by researchers to develop clinically promising radioprotective agents. In this article, for the first time we have discussed the impact of radioprotectors on different signaling pathways in cells, which will create a basis for scientific community working in this area to develop novel molecules with better therapeutic efficacy. The bright future of exceptionally noncytotoxic derivatives of bisbenzimidazoles is also described as radiomodulators. Amifostine, an effective radioprotectant, has been approved by the FDA for limited clinical use. However, due to its adverse side effects, it is not routinely used clinically. Recently, CBLB502 and several analog of a peptide are under clinical trial and showed high success against radiotherapy in cancer. This article reviews the different types of radioprotective agents with emphasis on the strategies for the development of novel radioprotectors for drug development. In addition, direction for future strategies relevant to the development of radioprotectors is also addressed. PMID:26807693

  8. 狂犬病流行态势及其防控策略的研究进展%Epidemic situation of rabies and advance in strategies for prevention and control of the disease

    Institute of Scientific and Technical Information of China (English)

    盛圆贤; 赵德明

    2009-01-01

    从狂犬病病毒的病原学特征、流行病学特征及狂犬病在我国的流行态势几方面论述了狂犬病的防控策略及研究进展,并针对其流行现状提出了完善法律法规、构建动物防疫长效机制、加强狂犬病的监测、加强犬类管理、实施免疫预防为主的防制措施等防控策略.%Advance in etiological and epidemiological characteristics of rabies virus were reviewed and the epidemic situation of rabies in China was reviewed. The measurements and strategies for prevention and control of rabies were summarized too. The proposals for improvement of the relative laws for control of animal diseases,establishment of long and effective mechanism for control of rabies, enhancement of moni-toring for rabies,strengthening of management of dogs,and immunization of all dogs should be put forward according to the epidemic situation of rabies.

  9. Occupant satisfaction with two blind control strategies

    DEFF Research Database (Denmark)

    Karlsen, Line Røseth; Heiselberg, Per Kvols; Bryn, Ida

    2015-01-01

    Highlights •Occupant satisfaction with two blind control strategies has been studied. •Control based on cut-off position of slats was more popular than closed slats. •Results from the study are helpful in development of control strategies for blinds. •The results give indications of how blinds...

  10. Advanced Coordinating Control System for Power Plant

    Institute of Scientific and Technical Information of China (English)

    WU Peng; WEI Shuangying

    2006-01-01

    The coordinating control system is popular used in power plant. This paper describes the advanced coordinating control by control methods and optimal operation, introduces their principals and features by using the examples of power plant operation. It is wealthy for automation application in optimal power plant operation.

  11. Advanced Sensors and Controls for Building Applications: Market Assessment and Potential R&D Pathways

    Energy Technology Data Exchange (ETDEWEB)

    Brambley, M. R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Haves, P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); McDonald, S. C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Torcellini, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hansen, D. [U.S. Dept. of Energy, Washington, D.C. (United States); Holmberg, D. R. [National Institute of Science and Technology, Gaithersburg, MD (United States); Roth, K. W. [TIAX, LLC, Cambridge, MA (United States)

    2005-04-01

    This document provides a market assessment of existing building sensors and controls and presents a range of technology pathways (R&D options) for pursuing advanced sensors and building control strategies.

  12. Smart — STATCOM control strategy implementation in wind power plants

    DEFF Research Database (Denmark)

    Sintamarean, Nicolae Christian; Cantarellas, Antoni Mir; Miranda, H.;

    2012-01-01

    converters is increasing. This paper deals with an advanced control strategy design of a three-level converter performing STATCOM and Active Filter functionalities. The proposed system is called Smart-STATCOM since it has the capability of self-controlling reactive power and harmonic voltages at the same...... time. Therefore, deciding the amount of non-active currents (fundamental, 5th and 7th harmonics) to be injected depending on the PCC voltage quality. Experimental results of the proposed control strategy are analyzed in order to validate the performance of the entire system....

  13. Control Strategy Tool (CoST)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The EPA Control Strategy Tool (CoST) is a software tool for projecting potential future control scenarios, their effects on emissions and estimated costs. This tool...

  14. Advanced control of piezoelectric micro-nano-positioning systems

    CERN Document Server

    Xu, Qingsong

    2016-01-01

    This book explores emerging methods and algorithms that enable precise control of micro-/nano-positioning systems. The text describes three control strategies: hysteresis-model-based feedforward control and hysteresis-model-free feedback control based on and free from state observation. Each paradigm receives dedicated attention within a particular part of the text. Readers are shown how to design, validate and apply a variety of new control approaches in micromanipulation: hysteresis modelling, discrete-time sliding-mode control and model-reference adaptive control. Experimental results are provided throughout and build up to a detailed treatment of practical applications in the fourth part of the book. The applications focus on control of piezoelectric grippers. Advanced Control of Piezoelectric Micro-/Nano-Positioning Systems will assist academic researchers and practising control and mechatronics engineers interested in suppressing sources of nonlinearity such as hysteresis and drift when combining positi...

  15. National Drug Control Strategy. 2008 Annual Report

    Science.gov (United States)

    Office of National Drug Control Policy, 2008

    2008-01-01

    This report presents the 2008 National Drug Control Strategy of the White House Office of National Drug Control Policy. The overarching goal of the President's Strategy is to reduce drug use in America through a balanced approach that focuses on stopping use before it starts, healing America's drug users, and disrupting the market for illegal…

  16. Advances and applications in nonlinear control systems

    CERN Document Server

    Volos, Christos

    2016-01-01

    The book reports on the latest advances and applications of nonlinear control systems. It consists of 30 contributed chapters by subject experts who are specialized in the various topics addressed in this book. The special chapters have been brought out in the broad areas of nonlinear control systems such as robotics, nonlinear circuits, power systems, memristors, underwater vehicles, chemical processes, observer design, output regulation, backstepping control, sliding mode control, time-delayed control, variables structure control, robust adaptive control, fuzzy logic control, chaos, hyperchaos, jerk systems, hyperjerk systems, chaos control, chaos synchronization, etc. Special importance was given to chapters offering practical solutions, modeling and novel control methods for the recent research problems in nonlinear control systems. This book will serve as a reference book for graduate students and researchers with a basic knowledge of electrical and control systems engineering. The resulting design proce...

  17. JPL Advanced Thermal Control Technology Roadmap - 2012

    Science.gov (United States)

    Birur, Gaj; Rodriguez, Jose I.

    2012-01-01

    NASA's new emphasis on human exploration program for missions beyond LEO requires development of innovative and revolutionary technologies. Thermal control requirements of future NASA science instruments and missions are very challenging and require advanced thermal control technologies. Limited resources requires organizations to cooperate and collaborate; government, industry, universities all need to work together for the successful development of these technologies.

  18. Robust missile feedback control strategies

    NARCIS (Netherlands)

    Trottemant, E.J.; Scherer, C.W.; Weiss, M.; Vermeulen, A.

    2010-01-01

    The nature of the missile interception problem with two noncooperative players leads to the field of differential games. Introducing nonlinear uncertain models can potentially lead to nonexistence of game theoretic equilibrium strategies, computationally intractable problems, and/or highly reduced p

  19. Advances in chaos theory and intelligent control

    CERN Document Server

    Vaidyanathan, Sundarapandian

    2016-01-01

    The book reports on the latest advances in and applications of chaos theory and intelligent control. Written by eminent scientists and active researchers and using a clear, matter-of-fact style, it covers advanced theories, methods, and applications in a variety of research areas, and explains key concepts in modeling, analysis, and control of chaotic and hyperchaotic systems. Topics include fractional chaotic systems, chaos control, chaos synchronization, memristors, jerk circuits, chaotic systems with hidden attractors, mechanical and biological chaos, and circuit realization of chaotic systems. The book further covers fuzzy logic controllers, evolutionary algorithms, swarm intelligence, and petri nets among other topics. Not only does it provide the readers with chaos fundamentals and intelligent control-based algorithms; it also discusses key applications of chaos as well as multidisciplinary solutions developed via intelligent control. The book is a timely and comprehensive reference guide for graduate s...

  20. Design and simulation of an automation system of a production process and fractionation of {sup 131}I, using strategies of advanced control; Diseno y simulacion de un sistema de automatizacion del proceso de produccion y fraccionamiento de {sup 131}I, utilizando estrategias de control avanzado

    Energy Technology Data Exchange (ETDEWEB)

    Paez, Jose; Arias, Pablo; Miranda, Jesus, E-mail: jpaez@jpen.gob.pe, E-mail: parias@ipen.gob.pe, E-mail: jmiranda@ipen.gob.pe [Instituto Peruano de Energia Nuclear (lPEN), Lima (Peru). Direccion de Servicios. Division de Instrumentacion Nuclear

    2013-10-01

    In this report, the results are obtained in the design and simulation of a control system using advanced strategies in a production cell in the Plant Production of Radioisotopes of IPEN. The results demonstrate that the temperature of the coalition oven is stabilized after 30 minutes, being constituted in an advantage to obtain the maximum yield of the cell production of {sup 131}I; also, an integral good controller has been designed that allows to obtain a mathematical model that reproduces with enough accuracy the behavior of the process. With the final simulation it has been to demonstrate that the System Control of Temperature of the Cell Production of {sup 131}I is a controllable system and allows to carry out the respective sequence with other variables of control of the production cell. (author)

  1. Wafer level reliability monitoring strategy of an advanced multi-process CMOS foundry

    NARCIS (Netherlands)

    Scarpa, Andrea; Tao, Guoqiao; Kuper, Fred G.

    2000-01-01

    In an advanced multi-process CMOS foundry it is strategically important to make use of an optimum reliability monitoring strategy, in order to be able to run well controlled processes. Philips Semiconductors Business Unit Foundries wafer fab MOS4YOU has developed an end-of-line ultra-fast reliabilit

  2. Planner-Based Control of Advanced Life Support Systems

    Science.gov (United States)

    Muscettola, Nicola; Kortenkamp, David; Fry, Chuck; Bell, Scott

    2005-01-01

    The paper describes an approach to the integration of qualitative and quantitative modeling techniques for advanced life support (ALS) systems. Developing reliable control strategies that scale up to fully integrated life support systems requires augmenting quantitative models and control algorithms with the abstractions provided by qualitative, symbolic models and their associated high-level control strategies. This will allow for effective management of the combinatorics due to the integration of a large number of ALS subsystems. By focusing control actions at different levels of detail and reactivity we can use faster: simpler responses at the lowest level and predictive but complex responses at the higher levels of abstraction. In particular, methods from model-based planning and scheduling can provide effective resource management over long time periods. We describe reference implementation of an advanced control system using the IDEA control architecture developed at NASA Ames Research Center. IDEA uses planning/scheduling as the sole reasoning method for predictive and reactive closed loop control. We describe preliminary experiments in planner-based control of ALS carried out on an integrated ALS simulation developed at NASA Johnson Space Center.

  3. Advanced control architecture for autonomous vehicles

    Science.gov (United States)

    Maurer, Markus; Dickmanns, Ernst D.

    1997-06-01

    An advanced control architecture for autonomous vehicles is presented. The hierarchical architecture consists of four levels: a vehicle level, a control level, a rule-based level and a knowledge-based level. A special focus is on forms of internal representation, which have to be chosen adequately for each level. The control scheme is applied to VaMP, a Mercedes passenger car which autonomously performs missions on German freeways. VaMP perceives the environment with its sense of vision and conventional sensors. It controls its actuators for locomotion and attention focusing. Modules for perception, cognition and action are discussed.

  4. MERCURY CONTROL WITH ADVANCED HYBRID PARTICULATE COLLECTOR

    Energy Technology Data Exchange (ETDEWEB)

    Ye Zhuang; Stanley J. Miller

    2005-05-01

    This project was awarded under U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Program Solicitation DE-PS26-00NT40769 and specifically addressed Technical Topical Area 4-Testing Novel and Less Mature Control Technologies on Actual Flue Gas at the Pilot Scale. The project team included the Energy & Environmental Research Center (EERC) as the main contractor; W.L. Gore & Associates, Inc., as a technical and financial partner; and the Big Stone Power Plant operated by Otter Tail Power Company, host for the field-testing portion of the research. Since 1995, DOE has supported development of a new concept in particulate control called the advanced hybrid particulate collector (AHPC). The AHPC has been licensed to W.L. Gore & Associates, Inc., and has been marketed as the Advanced Hybrid{trademark} filter by Gore. The Advanced Hybrid{trademark} filter combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The Advanced Hybrid{trademark} filter provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The Advanced Hybrid{trademark} filter also appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas--solid contactor. The objective of the project was to demonstrate 90% total mercury control in the Advanced Hybrid{trademark} filter at a lower cost than current mercury control estimates. The approach included bench-scale batch tests, larger-scale pilot testing with real flue gas on a coal-fired combustion system, and field demonstration at the 2.5-MW (9000-acfm) scale at a utility power plant to prove scale-up and demonstrate longer-term mercury control

  5. Optimized Information Transmission Scheduling Strategy Oriented to Advanced Metering Infrastructure

    Directory of Open Access Journals (Sweden)

    Weiming Tong

    2013-01-01

    Full Text Available Advanced metering infrastructure (AMI is considered to be the first step in constructing smart grid. AMI allows customers to make real-time choices about power utilization and enables power utilities to increase the effectiveness of the regional power grids by managing demand load during peak times and reducing unneeded power generation. These initiatives rely heavily on the prompt information transmission inside AMI. Aiming at the information transmission problem, this paper researches the communication scheduling strategy in AMI at a macroscopic view. First, the information flow of AMI is analyzed, and the power users are classified into several grades by their importance. Then, the defect of conventional information transmission scheduling strategy is analyzed. On this basis, two optimized scheduling strategies are proposed. In the wide area, an optimized scheduling strategy based on user importance and time critical is proposed to guarantee the important power users’ information transmission being handled promptly. In the local area, an optimized scheduling strategy based on device and information importance and time critical is proposed to guarantee the important devices and information in AMI user end system being handled promptly. At last, the two optimized scheduling strategies are simulated. The simulation results show that they can effectively improve the real-time performance and reliability of AMI information transmission.

  6. Overview of the US program of controls for advanced reactors

    International Nuclear Information System (INIS)

    An automated control system can incorporate control goals and strategies, assessment of present and future plant status, diagnostic evaluation and maintenance planning, and signal and command validation. It has not been feasible to employ these capabilities in conventional hard-wired, analog, control systems. Recent advances in computer-based digital data acquisition systems, process controllers, fiber-optic signal transmission artificial intelligence tools and methods, and small inexpensive, fast, large-capacity computers---with both numeric and symbolic capabilities---have provided many of the necessary ingredients for developing large, practical automated control systems. Furthermore, recent reactor designs which provide strong passive responses to operational upsets or accidents afford good opportunities to apply these advances in control technology. This paper presents an overall US national perspective for advanced controls research and development. The goals of high reliability, low operating cost and simple operation are described. The staged approach from conceptualization through implementation is discussed. Then the paper describes the work being done by ORNL, ANL and GE. The relationship of this work to the US commercial industry is also discussed

  7. Control strategies for demand controlled ventilation in dwellings

    DEFF Research Database (Denmark)

    Nielsen, Toke Rammer; Drivsholm, Christian

    2011-01-01

    and efficient fans is becoming the standard solution. The building regulation requirement for air change in dwellings is often a constant value that has been chosen to avoid moisture related problems in the indoor environment. This required air change is sometimes sufficient, sometimes too low and sometimes too....... In the studied house two control strategies were tested. A simple strategy where all sensors and controls were located in the air handling unit and only the speed of the fans can be controlled, and a complex strategy where sensors were placed in each room and where individual control of air flow in each room...

  8. Optimal Elevator Group Control by Evolution Strategies

    OpenAIRE

    Beielstein, Thomas; Ewald, Claus-Peter; MARKON, Sandor

    2003-01-01

    Efficient elevator group control is important for the operation of large buildings. Recent developments in this field include the use of fuzzy logic and neural networks. This paper summarizes the development of an evolution strategy (ES) that is capable of optimizing the neuro-controller of an elevator group controller. It extends the results that were based on a simplified elevator group controller simulator. A threshold selection technique is presented as a method to cope with noisy fitness...

  9. HTGR Resilient Control System Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Lynne M. Stevens

    2010-09-01

    A preeminent objective for corporate and government organizations is the protection of major investments, which is attained by achieving state awareness, a comprehensive understanding of security and safety, for critical infrastructures. Given the dependence of critical infrastructure on control systems for automation, the integrity of these systems and their ability to provide owner/operators a high degree of state awareness is essential in attaining a high degree of investment protection and public acceptance. Operators as well as government are therefore burdened to ensure they have a timely understanding of the status of their plant or all plants, respectively, to ensure efficient operations and investment and public protection. “This characterization is a significant objective that must consider many aspects of instrumentation, control, and intelligent systems in order to achieve the required result. These aspects include sensory, communication, analysis, decision, and human system interfaces necessary to achieve fusion of data and presentation of results that will provide an understanding of what issues are important and why.

  10. HTGR Resilient Control System Strategy

    International Nuclear Information System (INIS)

    A preeminent objective for corporate and government organizations is the protection of major investments, which is attained by achieving state awareness, a comprehensive understanding of security and safety, for critical infrastructures. Given the dependence of critical infrastructure on control systems for automation, the integrity of these systems and their ability to provide owner/operators a high degree of state awareness is essential in attaining a high degree of investment protection and public acceptance. Operators as well as government are therefore burdened to ensure they have a timely understanding of the status of their plant or all plants, respectively, to ensure efficient operations and investment and public protection. 'This characterization is a significant objective that must consider many aspects of instrumentation, control, and intelligent systems in order to achieve the required result. These aspects include sensory, communication, analysis, decision, and human system interfaces necessary to achieve fusion of data and presentation of results that will provide an understanding of what issues are important and why.

  11. Controlling air toxics through advanced coal preparation

    Energy Technology Data Exchange (ETDEWEB)

    Straszheim, W.E.; Buttermore, W.H.; Pollard, J.L. [Iowa State Univ., Ames, IA (United States)

    1995-11-01

    This project involves the assessment of advanced coal preparation methods for removing trace elements from coal to reduce the potential for air toxic emissions upon combustion. Scanning electron microscopy-based automated image analysis (SEM-AIA) and advanced washability analyses are being applied with state-of-the-art analytical procedures to predict the removal of elements of concern by advanced column flotation and to confirm the effectiveness of preparation on the quality of quantity of clean coal produced. Specific objectives are to maintain an acceptable recovery of combustible product, while improving the rejection of mineral-associated trace elements. Current work has focused on determining conditions for controlling column flotation system across its operating range and on selection and analysis of samples for determining trace element cleanability.

  12. Emerging trends in vibration control of wind turbines: a focus on a dual control strategy.

    Science.gov (United States)

    Staino, Andrea; Basu, Biswajit

    2015-02-28

    The paper discusses some of the recent developments in vibration control strategies for wind turbines, and in this context proposes a new dual control strategy based on the combination and modification of two recently proposed control schemes. Emerging trends in the vibration control of both onshore and offshore wind turbines are presented. Passive, active and semi-active structural vibration control algorithms have been reviewed. Of the existing controllers, two control schemes, active pitch control and active tendon control, have been discussed in detail. The proposed new control scheme is a merger of active tendon control with passive pitch control, and is designed using a Pareto-optimal problem formulation. This combination of controllers is the cornerstone of a dual strategy with the feature of decoupling vibration control from optimal power control as one of its main advantages, in addition to reducing the burden on the pitch demand. This dual control strategy will bring in major benefits to the design of modern wind turbines and is expected to play a significant role in the advancement of offshore wind turbine technologies. PMID:25583867

  13. INTEGRATED PLASMA CONTROL FOR ADVANCED TOKAMAKS

    Energy Technology Data Exchange (ETDEWEB)

    HUMPHREYS,D.A; FERRON,J.R; JOHNSON,R.D; LEUER,J.A; PENAFLOR,B.G; WALKER,M.L; WELANDER,A.S; KHAYRUTDINOV,R.R; DOKOUKA,V; EDGELL,D.H; FRANSSON,C.M

    2003-10-01

    OAK-B135 Advanced tokamaks (AT) are distinguished from conventional tokamaks by their high degree of shaping, achievement of profiles optimized for high confinement and stability characteristics, and active stabilization of MHD instabilities to attain high values of normalized beta and confinement. These high performance fusion devices thus require accurate regulation of the plasma boundary, internal profiles, pumping, fueling, and heating, as well as simultaneous and well-coordinated MHD control action to stabilize such instabilities as tearing modes and resistive wall modes. Satisfying the simultaneous demands on control accuracy, reliability, and performance for all of these subsystems requires a high degree of integration in both design and operation of the plasma control system in an advanced tokamak. The present work describes the approach, benefits, and progress made in integrated plasma control with application examples drawn from the DIII-D tokamak. The approach includes construction of plasma and system response models, validation of models against operating experiments, design of integrated controllers which operate in concert with one another as well as with supervisory modules, simulation of control action against off-line and actual machine control platforms, and iteration of the design-test loop to optimize performance.

  14. Supervisory Control System Architecture for Advanced Small Modular Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Cetiner, Sacit M [ORNL; Cole, Daniel L [University of Pittsburgh; Fugate, David L [ORNL; Kisner, Roger A [ORNL; Melin, Alexander M [ORNL; Muhlheim, Michael David [ORNL; Rao, Nageswara S [ORNL; Wood, Richard Thomas [ORNL

    2013-08-01

    This technical report was generated as a product of the Supervisory Control for Multi-Modular SMR Plants project within the Instrumentation, Control and Human-Machine Interface technology area under the Advanced Small Modular Reactor (SMR) Research and Development Program of the U.S. Department of Energy. The report documents the definition of strategies, functional elements, and the structural architecture of a supervisory control system for multi-modular advanced SMR (AdvSMR) plants. This research activity advances the state-of-the art by incorporating decision making into the supervisory control system architectural layers through the introduction of a tiered-plant system approach. The report provides a brief history of hierarchical functional architectures and the current state-of-the-art, describes a reference AdvSMR to show the dependencies between systems, presents a hierarchical structure for supervisory control, indicates the importance of understanding trip setpoints, applies a new theoretic approach for comparing architectures, identifies cyber security controls that should be addressed early in system design, and describes ongoing work to develop system requirements and hardware/software configurations.

  15. Wind farm models and control strategies

    DEFF Research Database (Denmark)

    Sørensen, Poul Ejnar; Hansen, Anca Daniela; Iov, F.;

    2005-01-01

    models for a fixed speed wind turbine with active stall control and a variable speed wind turbine with doubly-fed induction generator. After that, the 3 wind farm concepts and control strategies are described.The 3 concepts are AC connected doubly fed turbines, AC connected active stall turbines and DC......This report describes models and control strategies for 3 different concepts of wind farms. Initially, the potential in improvement of grid integration, structural loads and energy production is investigated in a survey of opportunities. Then simulationmodels are described, including wind turbine...

  16. Wind farm models and control strategies

    Energy Technology Data Exchange (ETDEWEB)

    Soerensen, Poul; Hansen, Anca D.; Iov, F.; Blaabjerg, F.; Donovan, M.H.

    2005-08-01

    This report describes models and control strategies for 3 different concepts of wind farms. Initially, the potential in improvement of grid integration, structural loads and energy production is investigated in a survey of opportunities. Then simulation models are described, including wind turbine models for a fixed speed wind turbine with active stall control and a variable speed wind turbine with doubly-fed induction generator. After that, the 3 wind farm concepts and control strategies are described. The 3 concepts are AC connected doubly fed turbines, AC connected active stall turbines and DC connected active stall turbines. Finally, some simulation examples and conclusions are presented. (au)

  17. An adaptive strategy for controlling chaotic system

    Institute of Scientific and Technical Information of China (English)

    曹一家; 张红先

    2003-01-01

    This paper presents an adaptive strategy for controlling chaotic systems. By employing the phase space reconstruction technique in nonlinear dynamical systems theory, the proposed strategy transforms the nonlinear system into canonical form, and employs a nonlinear observer to estimate the uncertainties and disturbances of the nonlinear system, and then establishes a state-error-like feedback law. The developed control scheme allows chaos control in spite of modeling errors and parametric variations. The effectiveness of the proposed approach has been demonstrated through its applications to two well-known chaotic systems : Duffing oscillator and Rǒssler chaos.

  18. An adaptive strategy for controlling chaotic system

    Institute of Scientific and Technical Information of China (English)

    曹一家; 张红先

    2003-01-01

    This paper presents an adaptive strategy for controlling chaotic systems. By employing the phase space reconstruction technique in nonlinear dynamical systems theory, the proposed strategy transforms the nonlinear system into canonical form, and employs a nonlinear observer to estimate the uncertainties and disturbances of the nonlinear system, and then establishes a state-error-like feedback law. The developed control scheme allows chaos control in spite of modeling errors and parametric variations. The effectiveness of the proposed approach has been demonstrated through its applications to two well-known chaotic systems: Duffing oscillator and Rossler chaos.

  19. Microeconomics of advanced process window control for 50-nm gates

    Science.gov (United States)

    Monahan, Kevin M.; Chen, Xuemei; Falessi, Georges; Garvin, Craig; Hankinson, Matt; Lev, Amir; Levy, Ady; Slessor, Michael D.

    2002-07-01

    Fundamentally, advanced process control enables accelerated design-rule reduction, but simple microeconomic models that directly link the effects of advanced process control to profitability are rare or non-existent. In this work, we derive these links using a simplified model for the rate of profit generated by the semiconductor manufacturing process. We use it to explain why and how microprocessor manufacturers strive to avoid commoditization by producing only the number of dies required to satisfy the time-varying demand in each performance segment. This strategy is realized using the tactic known as speed binning, the deliberate creation of an unnatural distribution of microprocessor performance that varies according to market demand. We show that the ability of APC to achieve these economic objectives may be limited by variability in the larger manufacturing context, including measurement delays and process window variation.

  20. Space Testing of the Advanced Instrument Controller

    OpenAIRE

    Goforth, Todd; Cannon, Scott; Lyke, James

    1999-01-01

    An extremely compact, low-power instrument controller and data processor system has been developed for space-based applications. Known as the Advanced Instrument Controller (AIC), this hybrid device contains both digital and analog components in a package less than 5 grams in weight and 2 x 3 em in size. Based on the Intel 8031151 microprocessor and implementing a superset of the 8051 instruction set, the AIC supports l28k of SRAM, 128k of EEPROM, four 8-bit parallel ports, six serial communi...

  1. Recent Advances in Iterative Learning Control

    Institute of Scientific and Technical Information of China (English)

    Jian-Xin XU

    2005-01-01

    In this paper we review the recent advances in three sub-areas of iterative learning control (ILC): 1) linear ILC for linear processes, 2) linear ILC for nonlinear processes which are global Lipschitz continuous (GLC), and 3) nonlinear ILC for general nonlinear processes. For linear processes, we focus on several basic configurations of linear ILC. For nonlinear processes with linear ILC, we concentrate on the design and transient analysis which were overlooked and missing for a long period. For general classes of nonlinear processes, we demonstrate nonlinear ILC methods based on Lyapunov theory, which is evolving into a new control paradigm.

  2. Low Activity Waste Feed Process Control Strategy

    International Nuclear Information System (INIS)

    The primary purpose of this document is to describe the overall process control strategy for monitoring and controlling the functions associated with the Phase 1B high-level waste feed delivery. This document provides the basis for process monitoring and control functions and requirements needed throughput the double-shell tank system during Phase 1 high-level waste feed delivery. This document is intended to be used by (1) the developers of the future Process Control Plan and (2) the developers of the monitoring and control system

  3. Low Activity Waste Feed Process Control Strategy

    Energy Technology Data Exchange (ETDEWEB)

    STAEHR, T.W.

    2000-06-14

    The primary purpose of this document is to describe the overall process control strategy for monitoring and controlling the functions associated with the Phase 1B high-level waste feed delivery. This document provides the basis for process monitoring and control functions and requirements needed throughput the double-shell tank system during Phase 1 high-level waste feed delivery. This document is intended to be used by (1) the developers of the future Process Control Plan and (2) the developers of the monitoring and control system.

  4. A Comprehensive LVRT Control Strategy for DFIG Wind Turbines With Enhanced Reactive Power Support

    DEFF Research Database (Denmark)

    Xie, Dongliang; Xu, Zhao; Yang, Lihui;

    2013-01-01

    The paper presents a new control strategy to enhance the ability of reactive power support of a doubly fed induction generator (DFIG) based wind turbine during serious voltage dips. The proposed strategy is an advanced low voltage ride through (LVRT) control scheme, with which a part of the captu...

  5. Control of Smart Building Using Advanced SCADA

    Science.gov (United States)

    Samuel, Vivin Thomas

    For complete control of the building, a proper SCADA implementation and the optimization strategy has to be build. For better communication and efficiency a proper channel between the Communication protocol and SCADA has to be designed. This paper concentrate mainly between the communication protocol, and the SCADA implementation, for a better optimization and energy savings is derived to large scale industrial buildings. The communication channel used in order to completely control the building remotely from a distant place. For an efficient result we consider the temperature values and the power ratings of the equipment so that while controlling the equipment, we are setting a threshold values for FDD technique implementation. Building management system became a vital source for any building to maintain it and for safety purpose. Smart buildings, refers to various distinct features, where the complete automation system, office building controls, data center controls. ELC's are used to communicate the load values of the building to the remote server from a far location with the help of an Ethernet communication channel. Based on the demand fluctuation and the peak voltage, the loads operate differently increasing the consumption rate thus results in the increase in the annual consumption bill. In modern days, saving energy and reducing the consumption bill is most essential for any building for a better and long operation. The equipment - monitored regularly and optimization strategy is implemented for cost reduction automation system. Thus results in the reduction of annual cost reduction and load lifetime increase.

  6. Assessing control strategies for ground level ozone

    Science.gov (United States)

    Sule, Neelesh Vijay

    2009-12-01

    Developing cost effective control strategies for ozone has been a challenge to air quality modelers. Conventionally, the control strategies are applied across-the board to the region. The main aim of this research was to develop a Decision-Making Framework (DMF) for evaluating and optimizing the selection of ozone control strategies. Conventional across-the-board reductions conduct emission reductions uniformly throughout the region and throughout the day. By contrast, this dissertation studied targeted reductions, in which emission sources of various types are reduced at various times and locations. The proposed DMF comprised of four phases: (1) Initialization, (2) Mining, (3) Metamodeling, and (4) Optimization. This DMF was tested on a DFW 2009 future case episode which was based on a 10-day episode from August 13-22, 1999. 612 emission variables were identified in three source categories viz. point, area (includes non-road) and line (on-road). The emission control regions and time periods along with ozone monitoring regions and time periods were defined. The control strategy emission reductions and costs were also identified in this stage. Initially a Latin hypercube experimental design was setup to organize 30 sets of emission reduction scenarios to be modeled using the photochemical model CAMx. Data mining reduced the number of variables to a maximum of 126. A second Latin hypercube was setup to organize another 30 emission reduction scenarios for the significant variables identified by data mining. Metamodels were developed for ozone from the 60 CAMx runs using linear regression models constructed with the stepwise model selection method. Stepwise regression further reduced the number of variables. The metamodels were implemented in optimization as a surrogate for time-intensive CAMx modeling. Appropriate constraints were calculated for each metamodel to ensure that it satisfied EPA's MAT. The optimization was formulated to find the most cost effective

  7. Advances in Intelligent Control Systems and Computer Science

    CERN Document Server

    2013-01-01

    The conception of real-time control networks taking into account, as an integrating approach, both the specific aspects of information and knowledge processing and the dynamic and energetic particularities of physical processes and of communication networks is representing one of the newest scientific and technological challenges. The new paradigm of Cyber-Physical Systems (CPS) reflects this tendency and will certainly change the evolution of the technology, with major social and economic impact. This book presents significant results in the field of process control and advanced information and knowledge processing, with applications in the fields of robotics, biotechnology, environment, energy, transportation, et al.. It introduces intelligent control concepts and strategies as well as real-time implementation aspects for complex control approaches. One of the sections is dedicated to the complex problem of designing software systems for distributed information processing networks. Problems as complexity an...

  8. On Control Strategies for Responsive Architectural Structures

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning; Parigi, Dario

    2012-01-01

    The present paper considers control of responsive architectural structures for improvement of structural performance by recognizing changes in their environments and loads, adapting to meet goals, and using past events to improve future performance or maintain serviceability. The general scope...... of the paper is to discuss control strategies for responsive architectural structures, particularly reconfigurable architectural structures which can transform body shape, i.e. a transformation into more than one or two different shape alternatives....

  9. On Control Strategies for Responsive Architectural Structures

    OpenAIRE

    Kirkegaard, Poul Henning; Parigi, Dario

    2012-01-01

    The present paper considers control of responsive architectural structures for improvement of structural performance by recognizing changes in their environments and loads, adapting to meet goals, and using past events to improve future performance or maintain serviceability. The general scope of the paper is to discuss control strategies for responsive architectural structures, particularly reconfigurable architectural structures which can transform body shape, i.e. a transformation into mor...

  10. Malaria vector control: current and future strategies

    NARCIS (Netherlands)

    Takken, W.; Knols, B.G.J.

    2009-01-01

    The recently announced call for malaria eradication represents a new page in the history of this disease. This has been triggered by remarkable reductions in malaria resulting from combined application of effective drugs and vector control. However, this strategy is threatened by development of inse

  11. JPL Advanced Thermal Control Technology Roadmap - 2008

    Science.gov (United States)

    Birur, Gaj

    2008-01-01

    This slide presentation reviews the status of thermal control technology at JPL and NASA.It shows the active spacecraft that are in vairous positions in the solar syatem, and beyond the solar system and the future missions that are under development. It then describes the challenges that the past missions posed with the thermal control systems. The various solutions that were implemented duirng the decades prior to 1990 are outlined. A review of hte thermal challenges of the future misions is also included. The exploration plan for Mars is then reviewed. The thermal challenges of the Mars Rovers are then outlined. Also the challenges of systems that would be able to be used in to explore Venus, and Titan are described. The future space telescope missions will also need thermal control technological advances. Included is a review of the thermal requirements for manned missions to the Moon. Both Active and passive technologies that have been used and will be used are reviewed. Those that are described are Mechanically Pumped Fluid Loops (MPFL), Loop Heat Pipes, an M3 Passive Cooler, Heat Siwtch for Space and Mars surface applications, phase change material (PCM) technology, a Gas Gap Actuateor using ZrNiH(x), the Planck Sorption Cooler (PCS), vapor compression -- Hybrid two phase loops, advanced pumps for two phase cooling loops, and heat pumps that are lightweight and energy efficient.

  12. Advances in dynamical systems and control

    CERN Document Server

    Zgurovsky, Mikhail

    2016-01-01

    Focused on recent advances, this book covers theoretical foundations as well as various applications. It presents modern mathematical modeling approaches to the qualitative and numerical analysis of solutions for complex engineering problems in physics, mechanics, biochemistry, geophysics, biology and climatology. Contributions by an international team of respected authors bridge the gap between abstract mathematical approaches, such as applied methods of modern analysis, algebra, fundamental and computational mechanics, nonautonomous and stochastic dynamical systems on the one hand, and practical applications in nonlinear mechanics, optimization, decision making theory and control theory on the other. As such, the book will be of interest to mathematicians and engineers working at the interface of these fields. .

  13. Situational Strategies for Self-Control.

    Science.gov (United States)

    Duckworth, Angela L; Gendler, Tamar Szabó; Gross, James J

    2016-01-01

    Exercising self-control is often difficult, whether declining a drink in order to drive home safely, passing on the chocolate cake to stay on a diet, or ignoring text messages to finish reading an important paper. But enacting self-control is not always difficult, particularly when it takes the form of proactively choosing or changing situations in ways that weaken undesirable impulses or potentiate desirable ones. Examples of situational self-control include the partygoer who chooses a seat far from where drinks are being poured, the dieter who asks the waiter not to bring around the dessert cart, and the student who goes to the library without a cell phone. Using the process model of self-control, we argue that the full range of self-control strategies can be organized by considering the timeline of the developing tempting impulse. Because impulses tend to grow stronger over time, situational self-control strategies-which can nip a tempting impulse in the bud-may be especially effective in preventing undesirable action. Ironically, we may underappreciate situational self-control for the same reason it is so effective-namely, that by manipulating our circumstances to advantage, we are often able to minimize the in-the-moment experience of intrapsychic struggle typically associated with exercising self-control. PMID:26817725

  14. Application of CyboCon Advanced Adjustment and Control Software Package in Delayed Coking Unit

    Institute of Scientific and Technical Information of China (English)

    Guo Hua

    2002-01-01

    This article refers to application of the CyboCon software package based upon the model-free adaptive control (MFA) in the 800-kt/a delayed coking unit to realize an advanced adjustment and control strategy for the temperature control of the heater. Operation tests have revealed the convenience in operating system and simplicity in maintenance, leading to good economic benefits.

  15. Advanced Wavefront Sensing and Control Testbed (AWCT)

    Science.gov (United States)

    Shi, Fang; Basinger, Scott A.; Diaz, Rosemary T.; Gappinger, Robert O.; Tang, Hong; Lam, Raymond K.; Sidick, Erkin; Hein, Randall C.; Rud, Mayer; Troy, Mitchell

    2010-01-01

    The Advanced Wavefront Sensing and Control Testbed (AWCT) is built as a versatile facility for developing and demonstrating, in hardware, the future technologies of wave front sensing and control algorithms for active optical systems. The testbed includes a source projector for a broadband point-source and a suite of extended scene targets, a dispersed fringe sensor, a Shack-Hartmann camera, and an imaging camera capable of phase retrieval wavefront sensing. The testbed also provides two easily accessible conjugated pupil planes which can accommodate the active optical devices such as fast steering mirror, deformable mirror, and segmented mirrors. In this paper, we describe the testbed optical design, testbed configurations and capabilities, as well as the initial results from the testbed hardware integrations and tests.

  16. Status and design of the Advanced Photon Source control system

    International Nuclear Information System (INIS)

    This paper presents the current status of the Advanced Photon Source (APS) control system. It will discuss the design decisions which led us to use industrial standards and collaborations with other laboratories to develop the APS control system. The system uses high performance graphic workstations and the X-windows Graphical User Interface (GUI) at the operator interface level. It connects to VME/VXI-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

  17. Polymeric nanotherapeutics: clinical development and advances in stealth functionalization strategies

    Science.gov (United States)

    Hu, Che-Ming J.; Fang, Ronnie H.; Luk, Brian T.; Zhang, Liangfang

    2013-12-01

    Long-circulating polymeric nanotherapeutics have garnered increasing interest in research and in the clinic owing to their ability to improve the solubility and pharmacokinetics of therapeutic cargoes. Modulation of carrier properties promises more effective drug localization at the disease sites and can lead to enhanced drug safety and efficacy. In the present review, we highlight the current development of polymeric nanotherapeutics in the clinic. In light of the importance of stealth properties in therapeutic nanoparticles, we also review the advances in stealth functionalization strategies and examine the performance of different stealth polymers in the literature. In addition, we discuss the recent development of biologically inspired ``self'' nanoparticles, which present a differing stealth concept from conventional approaches.

  18. Advanced-stage III/IV follicular lymphoma. Treatment strategies for individual patients

    Energy Technology Data Exchange (ETDEWEB)

    Heinzelmann, Frank; Bamberg, Michael; Weinmann, Martin [Dept. of Radiation Oncology, Univ. of Tuebingen (Germany); Ottinger, Hellmut [Dept. of Bone Marrow Transplantation, Univ. of Essen (Germany); Engelhard, Marianne [Dept. of Radiation Oncology, Univ. of Essen (Germany); Soekler, Martin [Dept. of Internal Medicine II, Univ. of Tuebingen (Germany)

    2010-05-15

    Background: in patients with advanced-stage III/IV follicular lymphoma (FL), there are many treatment options available. The current challenge is to choose the optimal strategy for the individual patient. Methods: the literature was reviewed with respect to treatment strategies in patients with advanced FL by screening the PubMed databank. Results: in advanced-stage III/IV FL, median survival may approach 8-10 years. Treatment strategies include a watch-and-wait strategy, chemoimmunotherapy, monotherapy with rituximab, and - as an experimental approach so far - radioimmunotherapy. The use of autologous hematopoietic stem cell transplantation (HSCT) for patients in first remission or chemosensitive relapse prolongs progression-free survival while the effect on overall survival remains unclear compared to standard chemotherapy. However, long-term results are flawed by high relapse rates and risk of secondary malignancies. In patients with relapsed/chemoresistant disease, allogeneic HSCT constitutes the only curative approach but is associated with high treatment-related mortality. In the palliative setting, low-dose involved-field irradiation constitutes an effective treatment option in order to control local symptoms with potential long-lasting response. Conclusion: in case of advanced-disease FL, asymptomatic patients can be managed expectantly. In symptomatic patients, chemoimmunotherapy is regarded as standard therapy. In symptomatic elderly patients with relevant comorbidities, rituximab {+-} single-agent chemotherapy, or low-dose involved-field radiotherapy might be appropriate. For younger patients with chemoresistant/relapsed disease, allogeneic HSCT might be considered, since advances in supportive care and better patient selection have resulted in improved outcomes. (orig.)

  19. Environmental Process Control: Strategies and Implementation

    Directory of Open Access Journals (Sweden)

    Jurgis Staniskis

    2006-04-01

    Full Text Available The structure and mathematical presentation of the optimal strategy for environmental process control is presented. This approach covers a wide variety of control systems, which have been constructed and analysed at the Institute of Environmental Engineering during the last fifteen years. Special attention is paid to the preventive environmental control and its tools: pollution prevention, life cycle assessment. The implementation results of preventive environmental control from more than 150 companies are presented in the paper.The investigations on water quality control issues are evaluated from the point of view of the interface between physico-ecological and socio-economical systems and decision support system based on river water quality model is suggested.

  20. Prototyping Advanced Control Systems on FPGA

    Directory of Open Access Journals (Sweden)

    Simard Stéphane

    2009-01-01

    Full Text Available In advanced digital control and mechatronics, FPGA-based systems on a chip (SoCs promise to supplant older technologies, such as microcontrollers and DSPs. However, the tackling of FPGA technology by control specialists is complicated by the need for skilled hardware/software partitioning and design in order to match the performance requirements of more and more complex algorithms while minimizing cost. Currently, without adequate software support to provide a straightforward design flow, the amount of time and efforts required is prohibitive. In this paper, we discuss our choice, adaptation, and use of a rapid prototyping platform and design flow suitable for the design of on-chip motion controllers and other SoCs with a need for analog interfacing. The platform consists of a customized FPGA design for the Amirix AP1000 PCI FPGA board coupled with a multichannel analog I/O daughter card. The design flow uses Xilinx System Generator in Matlab/Simulink for system design and test, and Xilinx Platform Studio for SoC integration. This approach has been applied to the analysis, design, and hardware implementation of a vector controller for 3-phase AC induction motors. It also has contributed to the development of CMC's MEMS prototyping platform, now used by several Canadian laboratories.

  1. Advanced Rooftop Control (ARC) Retrofit: Field-Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

    2013-07-31

    The multi-year research study was initiated to find solutions to improve packaged equipment operating efficiency in the field. Pacific Northwest National Laboratory (PNNL), with funding from the U.S. Department of Energy’s (DOE’s) Building Technologies Office (BTO) and Bonneville Power Administration (BPA) conducted this research, development and demonstration (RD&D) study. Packaged equipment with constant speed supply fans is designed to provide ventilation at the design rate at all times when the fan is operating as required by building code. Although there are a number of hours during the day when a building may not be fully occupied or the need for ventilation is lower than designed, the ventilation rate cannot be adjusted easily with a constant speed fan. Therefore, modulating the supply fan in conjunction with demand controlled ventilation (DCV) will not only reduce the coil energy but also reduce the fan energy. The objective of this multi-year research, development and demonstration project was to determine the magnitude of energy savings achievable by retrofitting existing packaged rooftop air conditioners with advanced control strategies not ordinarily used for packaged units. First, through detailed simulation analysis, it was shown that significant energy (between 24% and 35%) and cost savings (38%) from fan, cooling and heating energy consumption could be realized when packaged air conditioning units with gas furnaces are retrofitted with advanced control packages (combining multi-speed fan control, integrated economizer controls and DCV). The simulation analysis also showed significant savings for heat pumps (between 20% and 60%). The simulation analysis was followed by an extensive field test of a retrofittable advanced rooftop unit (RTU) controller.

  2. Night ventilation control strategies in office buildings

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhaojun; Yi, Lingli; Gao, Fusheng [School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China)

    2009-10-15

    In moderate climates night ventilation is an effective and energy-efficient approach to improve the indoor thermal environment for office buildings during the summer months, especially for heavyweight construction. However, is night ventilation a suitable strategy for office buildings with lightweight construction located in cold climates? In order to answer this question, the whole energy-consumption analysis software EnergyPlus was used to simulate the indoor thermal environment and energy consumption in typical office buildings with night mechanical ventilation in three cities in northern China. The summer outdoor climate data was analyzed, and three typical design days were chosen. The most important factors influencing night ventilation performance such as ventilation rates, ventilation duration, building mass and climatic conditions were evaluated. When night ventilation operation time is closer to active cooling time, the efficiency of night ventilation is higher. With night ventilation rate of 10 ach, the mean radiant temperature of the indoor surface decreased by up to 3.9 C. The longer the duration of operation, the more efficient the night ventilation strategy becomes. The control strategies for three locations are given in the paper. Based on the optimized strategies, the operation consumption and fees are calculated. The results show that more energy is saved in office buildings cooled by a night ventilation system in northern China than ones that do not employ this strategy. (author)

  3. Towards energy efficient operation of Heating, Ventilation and Air Conditioning systems via advanced supervisory control design

    Science.gov (United States)

    Oswiecinska, A.; Hibbs, J.; Zajic, I.; Burnham, K. J.

    2015-11-01

    This paper presents conceptual control solution for reliable and energy efficient operation of heating, ventilation and air conditioning (HVAC) systems used in large volume building applications, e.g. warehouse facilities or exhibition centres. Advanced two-level scalable control solution, designed to extend capabilities of the existing low-level control strategies via remote internet connection, is presented. The high-level, supervisory controller is based on Model Predictive Control (MPC) architecture, which is the state-of-the-art for indoor climate control systems. The innovative approach benefits from using passive heating and cooling control strategies for reducing the HVAC system operational costs, while ensuring that required environmental conditions are met.

  4. Novel strategies for control of fermentation processes

    DEFF Research Database (Denmark)

    Mears, Lisa; Stocks, Stuart; Sin, Gürkan;

    for the process engineer to optimise the operation conditions, due to a lack of available process models, and complex interactions between variables which are not easy to define, especially across scales and equipment. There is however a vast amount of batch process data generated, which can be investigated...... contributions to the prediction, and the variable trends, it may be possible to develop improved control strategies for these variables....

  5. Decoupling Control Strategy of D-STATCOM

    Directory of Open Access Journals (Sweden)

    Guangzheng Wang

    2013-06-01

    Full Text Available In Distribution Network, Distribution Static Synchronous Compensator (D-STATCOM can stabilize turn-on point voltage, effectively reduce the transmission losses in power, improve the power factor and prevent the non-linear load. But under the circumstance of the d- and q-axis, D-STATCOM is a non-linear and strong coupling system, so decoupling control is very useful, that is because the decoupling control can ensure the output current fast track and have on different with the setting values. Study the decoupling control strategy of D-STATCOM, through the analysis of its basic structure, and then get the model of the coupling term. Due to avoid active and reactive current coupling, Fuzzy Immune PI Controller and inverse system method are combined to be used in the original system. Finally, the results are shown by the MATLAB simulation that the proposed decoupling control strategy is very good, because the performance is excellent, the structure is simple and easy to be implemented.

  6. Some thoughts on separation control strategies

    Indian Academy of Sciences (India)

    P R Viswanath

    2007-02-01

    Separation control has received considerable emphasis in literature both owing to fundamental flow physics and technological applications. Flow separation generally leads to increased energy losses, instability and so on, and its control is essential to improve aerodynamic performance. Here a brief review is presented of three broad strategies for separation control: these include methods that involve energization of the boundary layer upstream of separation, those that involve altering the bubble flow or dead air zone, and those that may influence the shear layer reattachment directly. Examples from recent research in our laboratories are reviewed and it is suggested that direct manipulation of the reattachment process could lead to effective control/management.

  7. Advanced CIDI Emission Control System Development

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, Christine

    2006-05-31

    Ford Motor Company, with ExxonMobil and FEV, participated in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to develop an innovative emission control system for light-duty diesel vehicles. The focus on diesel engine emissions was a direct result of the improved volumetric fuel economy (up to 50%) and lower CO2 emissions (up to 25%) over comparable gasoline engines shown in Europe. Selective Catalytic Reduction (SCR) with aqueous urea as the NOx reductant and a Catalyzed Diesel Particulate Filter (CDPF) were chosen as the primary emission control system components. The program expected to demonstrate more than 90% durable reduction in particulate matter (PM) and NOx emissions on a light-duty truck application, based on the FTP-75 drive cycle. Very low sulfur diesel fuel (<15 ppm-wt) enabled lower PM emissions, reduced fuel economy penalty due to the emission control system and improved long-term system durability. Significant progress was made toward a durable system to meet Tier 2 Bin 5 emission standards on a 6000 lbs light-duty truck. A 40% reduction in engine-out NOx emissions was achieved with a mid-size prototype diesel engine through engine recalibration and increased exhaust gas recirculation. Use of a rapid warm-up strategy and urea SCR provided over 90% further NOx reduction while the CDPF reduced tailpipe PM to gasoline vehicle levels. Development work was conducted to separately improve urea SCR and CDPF system durability, as well as improved oxidation catalyst function. Exhaust gas NOx and ammonia sensors were also developed further. While the final emission control system did not meet Tier 2 Bin 5 NOx after 120k mi of aging on the dynamometer, it did meet the standards for HC, NMOG, and PM, and an improved SCR catalyst was shown to have potential to meet the NOx standard, assuming the DOC durability could be improved further. Models of DOC and SCR function were developed to guide the study of several key

  8. Advanced Controls for the Multi-pod Centipod WEC device

    Energy Technology Data Exchange (ETDEWEB)

    McCall, Alan [Dehlsen Associates, LLC, Santa Barabara, CA (United States); Fleming, Alex [Dehlsen Associates, LLC, Santa Barabara, CA (United States)

    2016-02-15

    Dehlsen Associates, LLC (DA) has developed a Wave Energy Converter (WEC), Centipod, which is a multiple point absorber, extracting wave energy primarily in the heave direction through a plurality of point absorber floats sharing a common stable reference structure. The objective of this project was to develop advanced control algorithms that will be used to reduce Levelized Cost of Energy (LCOE). This project investigated the use of Model Predictive Control (MPC) to improve the power capture of the WEC. The MPC controller developed in this work is a state-space, “look ahead” controller approach using knowledge of past and current states to predict future states to take action with the PTO to maximize power capture while still respecting system constraints. In order to maximize power, which is the product of force and velocity, the controller must aim to create phase alignment between excitation force and velocity. This project showed a 161% improvement in the Annual Energy Production (AEP) for the Centipod WEC when utilizing MPC, compared to a baseline, fixed passive damping control strategy. This improvement in AEP was shown to provide a substantial benefit to the WEC’s overall Cost of Energy, reducing LCOE by 50% from baseline. The results of this work proved great potential for the adoption of Model Predictive Controls in Wave Energy Converters.

  9. Dynamic Flow Control Strategies of Vehicle SCR Urea Dosing System

    Institute of Scientific and Technical Information of China (English)

    LIN Wei; ZHANG Youtong; ASIF Malik

    2015-01-01

    Selective Catalyst Reduction(SCR) Urea Dosing System(UDS) directly affects the system accuracy and the dynamic response performance of a vehicle. However, the UDS dynamic response is hard to keep up with the changes of the engine’s operating conditions. That will lead to low NOX conversion efficiency or NH3 slip. In order to optimize the injection accuracy and the response speed of the UDS in dynamic conditions, an advanced control strategy based on an air-assisted volumetric UDS is presented. It covers the methods of flow compensation and switching working conditions. The strategy is authenticated on an UDS and tested in different dynamic conditions. The result shows that the control strategy discussed results in higher dynamic accuracy and faster dynamic response speed of UDS. The inject deviation range is improved from being between–8%and 10%to–4%and 2%and became more stable than before, and the dynamic response time was shortened from 200 ms to 150 ms . The ETC cycle result shows that after using the new strategy the NH3 emission is reduced by 60%, and the NOX emission remains almost unchanged. The trade-off between NOX conversion efficiency and NH3 slip is mitigated. The studied flow compensation and switching working conditions can improve the dynamic performance of the UDS significantly and make the UDS dynamic response keep up with the changes of the engine’s operating conditions quickly.

  10. Dynamic flow control strategies of vehicle SCR Urea Dosing System

    Science.gov (United States)

    Lin, Wei; Zhang, Youtong; Asif, Malik

    2015-03-01

    Selective Catalyst Reduction(SCR) Urea Dosing System(UDS) directly affects the system accuracy and the dynamic response performance of a vehicle. However, the UDS dynamic response is hard to keep up with the changes of the engine's operating conditions. That will lead to low NO X conversion efficiency or NH3 slip. In order to optimize the injection accuracy and the response speed of the UDS in dynamic conditions, an advanced control strategy based on an air-assisted volumetric UDS is presented. It covers the methods of flow compensation and switching working conditions. The strategy is authenticated on an UDS and tested in different dynamic conditions. The result shows that the control strategy discussed results in higher dynamic accuracy and faster dynamic response speed of UDS. The inject deviation range is improved from being between -8% and 10% to -4% and 2% and became more stable than before, and the dynamic response time was shortened from 200 ms to 150 ms. The ETC cycle result shows that after using the new strategy the NH3 emission is reduced by 60%, and the NO X emission remains almost unchanged. The trade-off between NO X conversion efficiency and NH3 slip is mitigated. The studied flow compensation and switching working conditions can improve the dynamic performance of the UDS significantly and make the UDS dynamic response keep up with the changes of the engine's operating conditions quickly.

  11. Controlling strategy of dormant Mycobacterium tuberculosis

    Institute of Scientific and Technical Information of China (English)

    Gan Yiling; Guo Shuliang

    2014-01-01

    Objective This study aimed to review the available literatures on control of latent tuberculosis (TB) infection and propose a new control strategy to shorten the course of TB chemotherapy.Data sources The data used in this review were mainly obtained from articles listed in PubMed.The search terms were "therapy (treatment) of tuberculosis," "therapy (treatment) of latent TB infection," and "vaccine of TB."Study selection Articles regarding treatment and vaccine of TB were selected and reviewed.Results The most crucial reason causing the prolonged course of TB chemotherapy is the dormant state of Mycobacterium tuberculosis (M.tuberculosis).Nevertheless,there are,to date,no effective drugs that can directly kill the dormant cells of M.tuberculosis in clinical therapy.In accordance with the growth cycle of dormant M.tuberculosis in the body,the methods for controlling dormant M.tuberculosis include direct killing with drugs,prevention of dormant M.tuberculosis resuscitation with vaccines,and resuscitating dormant M.tuberculosis with preparations or drugs and then thoroughly killing these resuscitated M.tuberculosis by using anti-TB therapy.Conclusions The comprehensive analysis of the above three methods suggests that the drugs directly killing dormant cells are in clinical trials,TMC207 is the most beneficial for controlling TB.Because the side effect of vaccines is less and their action period is long,prevention of dormant cells resuscitation with vaccines is promising.The last control method makes it probable that when a huge number of active cells of M.tuberculosis have been killed and eradicated after 1-month short chemotherapy,only a strong short-term subsequent chemotherapy can completely kill and eradicate the remaining M.tuberculosis.This control strategy is expected to significantly shorten the course of TB chemotherapy and bring a new change and breakthrough in TB treatment.

  12. Active steering control strategy for articulated vehicles

    Institute of Scientific and Technical Information of China (English)

    Kyong-il KIM; Hsin GUAN; Bo WANG; Rui GUO; Fan LIANG

    2016-01-01

    To improve maneuverability and stability of articulated vehicles, we design an active steering controller, including tractor and trailer controllers, based on linear quadratic regulator (LQR) theory. First, a three-degree-of-freedom (3-DOF) model of the tractor-trailer with steered trailer axles is built. The simulated annealing particle swarm optimization (SAPSO) algorithm is applied to identify the key parameters of the model under specified vehicle speed and steering wheel angle. Thus, the key pa-rameters of the simplified model can be obtained according to the vehicle conditions using an online look-up table and interpola-tion. Simulation results show that vehicle parameter outputs of the simplified model and TruckSim agree well, thus providing the ideal reference yaw rate for the controller. Then the active steering controller of the tractor and trailer based on LQR is designed to follow the desired yaw rate and minimize their side-slip angle of the center of gravity (CG) at the same time. Finally, simulation tests at both low speed and high speed are conducted based on the TruckSim-Simulink program. The results show significant effects on the active steering controller on improving maneuverability at low speed and lateral stability at high speed for the articulated vehicle. The control strategy is applicable for steering not only along gentle curves but also along sharp curves.

  13. Multicontroller: an object programming approach to introduce advanced control algorithms for the GCS large scale project

    CERN Document Server

    Cabaret, S; Coppier, H; Rachid, A; Barillère, R; CERN. Geneva. IT Department

    2007-01-01

    The GCS (Gas Control System) project team at CERN uses a Model Driven Approach with a Framework - UNICOS (UNified Industrial COntrol System) - based on PLC (Programming Language Controller) and SCADA (Supervisory Control And Data Acquisition) technologies. The first' UNICOS versions were able to provide a PID (Proportional Integrative Derivative) controller whereas the Gas Systems required more advanced control strategies. The MultiController is a new UNICOS object which provides the following advanced control algorithms: Smith Predictor, PFC (Predictive Function Control), RST* and GPC (Global Predictive Control). Its design is based on a monolithic entity with a global structure definition which is able to capture the desired set of parameters of any specific control algorithm supported by the object. The SCADA system -- PVSS - supervises the MultiController operation. The PVSS interface provides users with supervision faceplate, in particular it links any MultiController with recipes: the GCS experts are ab...

  14. Advances in Risk Classification and Treatment Strategies for Neuroblastoma.

    Science.gov (United States)

    Pinto, Navin R; Applebaum, Mark A; Volchenboum, Samuel L; Matthay, Katherine K; London, Wendy B; Ambros, Peter F; Nakagawara, Akira; Berthold, Frank; Schleiermacher, Gudrun; Park, Julie R; Valteau-Couanet, Dominique; Pearson, Andrew D J; Cohn, Susan L

    2015-09-20

    Risk-based treatment approaches for neuroblastoma have been ongoing for decades. However, the criteria used to define risk in various institutional and cooperative groups were disparate, limiting the ability to compare clinical trial results. To mitigate this problem and enhance collaborative research, homogenous pretreatment patient cohorts have been defined by the International Neuroblastoma Risk Group classification system. During the past 30 years, increasingly intensive, multimodality approaches have been developed to treat patients who are classified as high risk, whereas patients with low- or intermediate-risk neuroblastoma have received reduced therapy. This treatment approach has resulted in improved outcome, although survival for high-risk patients remains poor, emphasizing the need for more effective treatments. Increased knowledge regarding the biology and genetic basis of neuroblastoma has led to the discovery of druggable targets and promising, new therapeutic approaches. Collaborative efforts of institutions and international cooperative groups have led to advances in our understanding of neuroblastoma biology, refinements in risk classification, and stratified treatment strategies, resulting in improved outcome. International collaboration will be even more critical when evaluating therapies designed to treat small cohorts of patients with rare actionable mutations.

  15. Genetic Control of Mosquitoes: population suppression strategies

    Directory of Open Access Journals (Sweden)

    André Barretto Bruno Wilke

    2012-10-01

    Full Text Available Over the last two decades, morbidity and mortality from malaria and dengue fever among other pathogens are an increasing Public Health problem. The increase in the geographic distribution of vectors is accompanied by the emergence of viruses and diseases in new areas. There are insufficient specific therapeutic drugs available and there are no reliable vaccines for malaria or dengue, although some progress has been achieved, there is still a long way between its development and actual field use. Most mosquito control measures have failed to achieve their goals, mostly because of the mosquito's great reproductive capacity and genomic flexibility. Chemical control is increasingly restricted due to potential human toxicity, mortality in no target organisms, insecticide resistance, and other environmental impacts. Other strategies for mosquito control are desperately needed. The Sterile Insect Technique (SIT is a species-specific and environmentally benign method for insect population suppression, it is based on mass rearing, radiation mediated sterilization, and release of a large number of male insects. Releasing of Insects carrying a dominant lethal gene (RIDL offers a solution to many of the drawbacks of traditional SIT that have limited its application in mosquitoes while maintaining its environmentally friendly and species-specific utility. The self-limiting nature of sterile mosquitoes tends to make the issues related to field use of these somewhat less challenging than for self-spreading systems characteristic of population replacement strategies. They also are closer to field use, so might be appropriate to consider first. The prospect of genetic control methods against mosquito vectored human diseases is rapidly becoming a reality, many decisions will need to be made on a national, regional and international level regarding the biosafety, social, cultural and ethical aspects of the use and deployment of these vector control methods.

  16. Persistent organic pollutants control strategy in China

    Institute of Scientific and Technical Information of China (English)

    SHI Ya-juan; LU Yong-long; ZHANG Hong; WANG Tie-yu; XING Ying

    2005-01-01

    The development of Persistent Organic Pollutants(POPs) control policy in China in the context of international concerns on POPs was reviewed. The aspects of the Chinese POPs control strategies were analyzed, and compared with those of developed counterparts (e.g. US, EU, Japan). Currently, while the legal framework on POPs management, which complies with international guidelines has been established, it should be improved in the areas of special POPs management, risk assessment, the precautionary principle, lifecycle management and technical support capacity. The analysis of Chinese POPs policy and suggestions for strengthening the sciencebased decision making capacity are not only useful for Chinese decision-makers, but also a case study for developing world and make a great contribution for the global elimination of POPs to make a toxic-free future.

  17. Ervaringen met Advanced Cruise Control (ACC) in een korte praktijkproef.

    NARCIS (Netherlands)

    Oei, H.-l.

    2003-01-01

    Experiences with Advanced Cruise Control in traffic; a limited experiment. Advanced Cruise Control (ACC) is an ordinary cruise control in which the desired speed is installed manually, but in which the headway time to the vehicle in front is also taken into account. If the headway time becomes less

  18. Strategies For Malaria Control In Mangalore City

    Directory of Open Access Journals (Sweden)

    Kiran Udaya .N

    1999-01-01

    Full Text Available Research questions: What different strategies should be used to effectively control problem of malaria? Objectives: 1 To study the problem of malaria. 2 To study different strategies for effective control of malaria. Study design: Observational and record based. The problem of malaria was studied for three years from 1996-1998 Participants: Individuals having fever. Setting: Community based in Mangalore City. Study variables: Fever cases, blood slides prepared, slides found positive, agency-wise, species-wise and year-wise positivity. Statistical methods: Simple proportions. Results: The yield of cases has been shown to highest in passive surveillance, as reflected in high slide positivity rates. A total of 95,898 slides were prepared, out of which 19,169 were positive for malaria parasite. Thus, the overall side positivity was 20%. The SPR in passive surveillance was 34.5%. Month-wise distribution of positive cases showed high SPR and low Pv/Pf ratios during non-malaria seasons. It is suggested to improve passive surveillance to achieve high SPR thereby leading to substantial saving on slides, laboratory services and transport expenditure.

  19. Control strategies for vehicular NOx emissions in Guangzhou, China

    International Nuclear Information System (INIS)

    Guangzhou is a city in southern China that has experienced very rapid economic development in recent years. The city's air has very high concentrations of various pollutants, including sulphur dioxide (SO2, oxides of nitrogen (NOx), ozone (O3) and particulate. This paper reviews the changes in air quality in the city over the past 15 years, and notes that a serious vehicular-related emissions problem has been superimposed on the traditional coal-burning problem evident in most Chinese cities. As NOx concentrations have increased, oxidants and photochemical smog now interact with the traditional SO2 and particulate pollutants, leading to increased health risks and other environmental concerns. Any responsible NOx control strategy for the city must include vehicle emission control measures. This paper reviews control strategies designed to abate vehicle emissions to fulfill the city's air quality improvement target in 2010. A cost-effectiveness analysis suggests that, while NOx emission control is expensive, vehicular emission standards could achieve a relatively sizable emissions reduction at reasonable cost. To achieve the 2010 air quality target of NOx, advanced implementation of EURO3 standards is recommended, substituting for the EURO2 currently envisioned in the national regulations Related technical options, including fuel quality improvements and inspection/maintenance (I/M) upgrades (ASM or IM240) are assessed as well. (author)

  20. Nosocomial infections and their control strategies

    Institute of Scientific and Technical Information of China (English)

    Hassan Ahmed Khan; Aftab Ahmad; Riffat Mehboob

    2015-01-01

    Nosocomial infections are also known as hospital-acquired/associated infections. National Healthcare Safety Network along with Centers for Disease Control for surveillance has classified nosocomial infection sites into 13 types with 50 infection sites, which are specific on the basis of biological and clinical criteria. The agents that are usually involved in hospital-acquired infections include Streptococcus spp., Acinetobacter spp., enterococci, Pseudomonas aeruginosa, coagulase-negative staphylococci, Staphylococcus aureus, Bacillus cereus, Legionella and Enterobacteriaceae family members, namely, Proteus mirablis, Klebsiella pneumonia, Escherichia coli, Serratia marcescens. Nosocomial pathogens can be transmitted through person to person, environment or contaminated water and food, infected individuals, contaminated healthcare personnel’s skin or contact via shared items and surfaces. Mainly, multi-drug-resistant nosocomial organisms include methicillin-resistant Staphylococcus aureus, vancomycin-resistant enterococci, Pseudomonas aeruginosa and Klebsiella pneumonia, whereas Clostridium dififcile shows natural resistance. Excessive and improper use of broad-spectrum antibiotics, especially in healthcare settings, is elevating nosocomial infections, which not only becomes a big health care problem but also causes great economic and production loss in the community. Nosocomial infections can be controlled by measuring and comparing the infection rates within healthcare settings and sticking to the best healthcare practices. Centers for Disease Control and Prevention provides the methodology for surveillance of nosocomial infections along with investigation of major outbreaks. By means of this surveillance, hospitals can devise a strategy comprising of infection control practices.

  1. Nosocomial infections and their control strategies

    Institute of Scientific and Technical Information of China (English)

    Hassan; Ahmed; Khan; Aftab; Ahmad; Riffat; Mehboob

    2015-01-01

    Nosocomial infections are also known as hospital-acquired/associated infections. National Healthcare Safety Network along with Centers for Disease Control for surveillance has classified nosocomial infection sites into 13 types with 50 infection sites, which are specific on the basis of biological and clinical criteria. The agents that are usually involved in hospitalacquired infections include Streptococcus spp., Acinetobacter spp., enterococci, Pseudomonas aeruginosa, coagulase-negative staphylococci, Staphylococcus aureus, Bacillus cereus, Legionella and Enterobacteriaceae family members, namely, Proteus mirablis, Klebsiella pneumonia, Escherichia coli, Serratia marcescens. Nosocomial pathogens can be transmitted through person to person, environment or contaminated water and food, infected individuals, contaminated healthcare personnel’s skin or contact via shared items and surfaces. Mainly, multi-drug-resistant nosocomial organisms include methicillin-resistant Staphylococcus aureus, vancomycin-resistant enterococci, Pseudomonas aeruginosa and Klebsiella pneumonia, whereas Clostridium difficile shows natural resistance. Excessive and improper use of broadspectrum antibiotics, especially in healthcare settings, is elevating nosocomial infections, which not only becomes a big health care problem but also causes great economic and production loss in the community. Nosocomial infections can be controlled by measuring and comparing the infection rates within healthcare settings and sticking to the best healthcare practices. Centers for Disease Control and Prevention provides the methodology for surveillance of nosocomial infections along with investigation of major outbreaks. By means of this surveillance, hospitals can devise a strategy comprising of infection control practices.

  2. Strategies for Controlled Placement of Nanoscale Building Blocks

    Directory of Open Access Journals (Sweden)

    Koh SeongJin

    2007-01-01

    Full Text Available AbstractThe capability of placing individual nanoscale building blocks on exact substrate locations in a controlled manner is one of the key requirements to realize future electronic, optical, and magnetic devices and sensors that are composed of such blocks. This article reviews some important advances in the strategies for controlled placement of nanoscale building blocks. In particular, we will overview template assisted placement that utilizes physical, molecular, or electrostatic templates, DNA-programmed assembly, placement using dielectrophoresis, approaches for non-close-packed assembly of spherical particles, and recent development of focused placement schemes including electrostatic funneling, focused placement via molecular gradient patterns, electrodynamic focusing of charged aerosols, and others.

  3. 40 CFR 52.2584 - Control strategy; Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not...

  4. Control strategies based on effective power factor for distributed generation power plants during unbalanced grid voltage

    OpenAIRE

    Camacho Santiago, Antonio; Castilla Fernández, Miguel; Miret Tomàs, Jaume; Matas Alcalá, José; Guzmán Solà, Ramon; de Sousa Pérez, Óscar; Martí Colom, Pau; García de Vicuña Muñoz de la Nava, José Luis

    2013-01-01

    Unbalanced voltages in three-phase power systems is a common perturbation propagated along the grid. Distributed Generation plants have gained widespread attention due to their capability to improve power quality in a distributed manner, including voltage unbalance mitigation. A conventional control strategy to command power plants during balanced grid voltages, is the use of power factor to inject/absorb reactive power depending on grid conditions. Advanced control strategies during unbalanc...

  5. Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices

    Energy Technology Data Exchange (ETDEWEB)

    McEntee, Jarlath [Ocean Renewable Power Company, Portland, ME (United States); Polagye, Brian [Ocean Renewable Power Company, Portland, ME (United States); Fabien, Brian [Ocean Renewable Power Company, Portland, ME (United States); Thomson, Jim [Ocean Renewable Power Company, Portland, ME (United States); Kilcher, Levi [Ocean Renewable Power Company, Portland, ME (United States); Marnagh, Cian [Ocean Renewable Power Company, Portland, ME (United States); Donegan, James [Ocean Renewable Power Company, Portland, ME (United States)

    2016-03-31

    The Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices (Project) investigated, analyzed and modeled advanced turbine control schemes with the objective of increasing the energy harvested by hydrokinetic turbines in turbulent flow. Ocean Renewable Power Company (ORPC) implemented and validated a feedforward controller to increase power capture; and applied and tested the controls on ORPC’s RivGen® Power Systems in Igiugig, Alaska. Assessments of performance improvements were made for the RivGen® in the Igiugig environment and for ORPC’s TidGen® Power System in a reference tidal environment. Annualized Energy Production (AEP) and Levelized Cost of Energy (LCOE) improvements associated with implementation of the recommended control methodology were made for the TidGen® Power System in the DOE reference tidal environment. System Performance Advancement (SPA) goals were selected for the project. SPA targets were to improve Power to Weight Ratio (PWR) and system Availability, with the intention of reducing Levelized Cost of Electricity (LCOE). This project focused primarily reducing in PWR. Reductions in PWR of 25.5% were achieved. Reductions of 20.3% in LCOE were achieved. This project evaluated four types of controllers which were tested in simulation, emulation, a laboratory flume, and the field. The adaptive Kω2 controller performs similarly to the non-adaptive version of the same controller and may be useful in tidal channels where the mean velocity is continually evolving. Trends in simulation were largely verified through experiments, which also provided the opportunity to test assumptions about turbine responsiveness and control resilience to varying scales of turbulence. Laboratory experiments provided an essential stepping stone between simulation and implementation on a field-scale turbine. Experiments also demonstrated that using “energy loss” as a metric to differentiate between well-designed controllers operating at

  6. The Effect of Advanced Management Accounting Practices on the Competitive Strategies and Performance

    OpenAIRE

    Rahmi Yücel; Kayhan Ahmetoğulları

    2015-01-01

    This study is based on a sample of 300 managers from the production industry of West Marmara Region. The goal of this study is to examine the interaction among advanced management accounting practices, competitive strategies and company performance. As a result of study, it is found that advanced accounting management practices have a positive effect on the company performance and competitive strategies. In addition, competitive strategies have an effect on the company performance positively....

  7. Chemical Biology Strategies for Biofilm Control.

    Science.gov (United States)

    Yang, Liang; Givskov, Michael

    2015-08-01

    Microbes live as densely populated multicellular surface-attached biofilm communities embedded in self-generated, extracellular polymeric substances (EPSs). EPSs serve as a scaffold for cross-linking biofilm cells and support development of biofilm architecture and functions. Biofilms can have a clear negative impact on humans, where biofilms are a common denominator in many chronic diseases in which they prime development of destructive inflammatory conditions and the failure of our immune system to efficiently cope with them. Our current assortment of antimicrobial agents cannot efficiently eradicate biofilms. For industrial applications, the removal of biofilms within production machinery in the paper and hygienic food packaging industry, cooling water circuits, and drinking water manufacturing systems can be critical for the safety and efficacy of those processes. Biofilm formation is a dynamic process that involves microbial cell migration, cell-to-cell signaling and interactions, EPS synthesis, and cell-EPS interactions. Recent progress of fundamental biofilm research has shed light on novel chemical biology strategies for biofilm control. In this article, chemical biology strategies targeting the bacterial intercellular and intracellular signaling pathways will be discussed.

  8. Designing a sustainable strategy for malaria control?

    Directory of Open Access Journals (Sweden)

    Mharakurwa Sungano

    2011-08-01

    Full Text Available Abstract Malaria in the 21st century is showing signs of declining over much of its distribution, including several countries in Africa where previously this was not thought to be feasible. Yet for the most part the strategies to attack the infection are similar to those of the 1950s. Three major Journals have recently drawn attention to the situation, stressing the importance of research, describing the successes and defining semantics related to control. But there is a need to stress the importance of local sustainability, and consider somewhat urgently how individual endemic countries can plan and implement the programmes that are currently financed, for the most part, by donor institutions. On an immediate basis research should be more focused on a data driven approach to control. This will entail new thinking on the role of local infrastructure and in training of local scientists in local universities in epidemiology and field malariology so that expanded control programmes can become operational. Donor agencies should encourage and facilitate development of career opportunities for such personnel so that local expertise is available to contribute appropriately.

  9. A Composite PWM Control Strategy for Boost Converter

    Science.gov (United States)

    Qingfeng, Liu; Zhaoxia, Leng; Jinkun, Sun; Huamin, Wang

    In order to improve the control performance of boost converter with large signal disturbance, a composite PWM control strategy for boost converter operating in continuous condition mode (CCM) was proposed in this paper. The parasitical loss of Boost converter was analyzed and a loss compensation strategy was adopted to design feed-forward tracker for converter. The composite PWM controller consisted of the tracker and PID controller. Simulation and experiment results validated the validity of the control strategy presented in this paper.

  10. Instantaneous Current Feedback Control Strategy on Buck Mode Inverter

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Control strategies for Buck mode inverter have important effect on static and dynamic characteristics, reliability, load capacity, and short-circuit resistance. Instantaneous current feedback control strategies include instantaneous inductor current feedback control and instantaneous capacitor current feedback control, both of which have essential difference. When the Buck mode inverter respectively adopts instantaneous inductor current and capacitor current feedback control strategies, characteristics of stability, output voltage and power, short circuit, nonlinear load and dynamic are fully investigated in this paper.

  11. Advanced and controlled drug delivery systems in clinical disease management

    NARCIS (Netherlands)

    Brouwers, JRBJ

    1996-01-01

    Advanced and controlled drug delivery systems are important for clinical disease management. In this review the most important new systems which have reached clinical application are highlighted. Microbiologically controlled drug delivery is important for gastrointestinal diseases like ulcerative co

  12. Advanced Variance Reduction Strategies for Optimizing Mesh Tallies in MAVRIC

    International Nuclear Information System (INIS)

    More often than in the past, Monte Carlo methods are being used to compute fluxes or doses over large areas using mesh tallies (a set of region tallies defined on a mesh that overlays the geometry). For problems that demand that the uncertainty in each mesh cell be less than some set maximum, computation time is controlled by the cell with the largest uncertainty. This issue becomes quite troublesome in deep-penetration problems, and advanced variance reduction techniques are required to obtain reasonable uncertainties over large areas. The CADIS (Consistent Adjoint Driven Importance Sampling) methodology has been shown to very efficiently optimize the calculation of a response (flux or dose) for a single point or a small region using weight windows and a biased source based on the adjoint of that response. This has been incorporated into codes such as ADVANTG (based on MCNP) and the new sequence MAVRIC, which will be available in the next release of SCALE. In an effort to compute lower uncertainties everywhere in the problem, Larsen's group has also developed several methods to help distribute particles more evenly, based on forward estimates of flux. This paper focuses on the use of a forward estimate to weight the placement of the source in the adjoint calculation used by CADIS, which we refer to as a forward-weighted CADIS (FW-CADIS)

  13. Advanced control of a water supply system: a case study

    NARCIS (Netherlands)

    Bakker, M.; Rajewicz, T.; Kien, H.; Vreeburg, J.H.G.; Rietveld, L.C.

    2014-01-01

    Conventional automatic production flow control and pump pressure control of water supply systems are robust and simple: production flow is controlled based on the level in the clear water reservoir and pump pressure is controlled on a static set-point. Recently, more advanced computer-based control

  14. Generic Model Predictive Control Framework for Advanced Driver Assistance Systems

    NARCIS (Netherlands)

    Wang, M.

    2014-01-01

    This thesis deals with a model predictive control framework for control design of Advanced Driver Assistance Systems, where car-following tasks are under control. The framework is applied to design several autonomous and cooperative controllers and to examine the controller properties at the microsc

  15. Contribution to the study and design of advanced controllers : application to smelting furnaces

    OpenAIRE

    Ojeda Sarmiento, Juan Manuel

    2013-01-01

    In this doctoral thesis, contributions to the study and design of advanced controllers and their application to metallurgical smelting furnaces are discussed. For this purpose, this kind of plants has been described in detail. The case of study is an Isasmelt plant in south Peru, which yearly processes 1.200.000 tons of copper concentrate. The current control system is implemented on a distributed control system. The main structure includes a cascade strategy to regulate the molten bath tempe...

  16. Parasitic Nematode Immunomodulatory Strategies: Recent Advances and Perspectives

    Science.gov (United States)

    Cooper, Dustin; Eleftherianos, Ioannis

    2016-01-01

    More than half of the described species of the phylum Nematoda are considered parasitic, making them one of the most successful groups of parasites. Nematodes are capable of inhabiting a wide variety of niches. A vast array of vertebrate animals, insects, and plants are all identified as potential hosts for nematode parasitization. To invade these hosts successfully, parasitic nematodes must be able to protect themselves from the efficiency and potency of the host immune system. Innate immunity comprises the first wave of the host immune response, and in vertebrate animals it leads to the induction of the adaptive immune response. Nematodes have evolved elegant strategies that allow them to evade, suppress, or modulate host immune responses in order to persist and spread in the host. Nematode immunomodulation involves the secretion of molecules that are capable of suppressing various aspects of the host immune response in order to promote nematode invasion. Immunomodulatory mechanisms can be identified in parasitic nematodes infecting insects, plants, and mammals and vary greatly in the specific tactics by which the parasites modify the host immune response. Nematode-derived immunomodulatory effects have also been shown to affect, negatively or positively, the outcome of some concurrent diseases suffered by the host. Understanding nematode immunomodulatory actions will potentially reveal novel targets that will in turn lead to the development of effective means for the control of destructive nematode parasites. PMID:27649248

  17. Parasitic Nematode Immunomodulatory Strategies: Recent Advances and Perspectives.

    Science.gov (United States)

    Cooper, Dustin; Eleftherianos, Ioannis

    2016-01-01

    More than half of the described species of the phylum Nematoda are considered parasitic, making them one of the most successful groups of parasites. Nematodes are capable of inhabiting a wide variety of niches. A vast array of vertebrate animals, insects, and plants are all identified as potential hosts for nematode parasitization. To invade these hosts successfully, parasitic nematodes must be able to protect themselves from the efficiency and potency of the host immune system. Innate immunity comprises the first wave of the host immune response, and in vertebrate animals it leads to the induction of the adaptive immune response. Nematodes have evolved elegant strategies that allow them to evade, suppress, or modulate host immune responses in order to persist and spread in the host. Nematode immunomodulation involves the secretion of molecules that are capable of suppressing various aspects of the host immune response in order to promote nematode invasion. Immunomodulatory mechanisms can be identified in parasitic nematodes infecting insects, plants, and mammals and vary greatly in the specific tactics by which the parasites modify the host immune response. Nematode-derived immunomodulatory effects have also been shown to affect, negatively or positively, the outcome of some concurrent diseases suffered by the host. Understanding nematode immunomodulatory actions will potentially reveal novel targets that will in turn lead to the development of effective means for the control of destructive nematode parasites. PMID:27649248

  18. Advanced Algorithms for Local Routing Strategy on Complex Networks

    Science.gov (United States)

    Lin, Benchuan; Chen, Bokui; Gao, Yachun; Tse, Chi K.; Dong, Chuanfei; Miao, Lixin; Wang, Binghong

    2016-01-01

    Despite the significant improvement on network performance provided by global routing strategies, their applications are still limited to small-scale networks, due to the need for acquiring global information of the network which grows and changes rapidly with time. Local routing strategies, however, need much less local information, though their transmission efficiency and network capacity are much lower than that of global routing strategies. In view of this, three algorithms are proposed and a thorough investigation is conducted in this paper. These algorithms include a node duplication avoidance algorithm, a next-nearest-neighbor algorithm and a restrictive queue length algorithm. After applying them to typical local routing strategies, the critical generation rate of information packets Rc increases by over ten-fold and the average transmission time 〈T〉 decreases by 70–90 percent, both of which are key physical quantities to assess the efficiency of routing strategies on complex networks. More importantly, in comparison with global routing strategies, the improved local routing strategies can yield better network performance under certain circumstances. This is a revolutionary leap for communication networks, because local routing strategy enjoys great superiority over global routing strategy not only in terms of the reduction of computational expense, but also in terms of the flexibility of implementation, especially for large-scale networks. PMID:27434502

  19. 40 CFR 52.1025 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1025 Section 52.1025 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... strategy: Particulate matter. (a) The revisions to the control strategy resulting from the modification...

  20. Advanced nonlinear engine speed control systems

    DEFF Research Database (Denmark)

    Vesterholm, Thomas; Hendricks, Elbert

    1994-01-01

    Several subsidiary control problems have turned out to be important for improving driveability and fuel consumption in modern spark ignition (SI) engine cars. Among these are idle speed control and cruise control. In this paper the idle speed and cruise control problems will be treated as one...

  1. Modeling and Advanced Control for Sustainable Process Systems (chapter 5)

    Science.gov (United States)

    This book chapter introduces a novel process systems engineering framework that integrates process control with sustainability assessment tools for the simultaneous evaluation and optimization of process operations. The implemented control strategy consists of a biologically-insp...

  2. Practical Implementations of Advanced Process Control for Linear Systems

    DEFF Research Database (Denmark)

    Knudsen, Jørgen K . H.; Huusom, Jakob Kjøbsted; Jørgensen, John Bagterp

    2013-01-01

    Most advanced process control systems are based on Model Predictive Control (MPC). In this paper we discuss three critical issues for the practical implementation of linear MPC for process control applications. The rst issue is related to oset free control and disturbance models; the second issue...

  3. Advanced, Integrated Control for Building Operations to Achieve 40% Energy Saving

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yan; Song, Zhen; Loftness, Vivian; Ji, Kun; Zheng, Sam; Lasternas, Bertrand; Marion, Flore; Yuebin, Yu

    2012-10-15

    We developed and demonstrated a software based integrated advanced building control platform called Smart Energy Box (SEB), which can coordinate building subsystem controls, integrate variety of energy optimization algorithms and provide proactive and collaborative energy management and control for building operations using weather and occupancy information. The integrated control system is a low cost solution and also features: Scalable component based architecture allows to build a solution for different building control system configurations with needed components; Open Architecture with a central data repository for data exchange among runtime components; Extendible to accommodate variety of communication protocols. Optimal building control for central loads, distributed loads and onsite energy resource; uses web server as a loosely coupled way to engage both building operators and building occupants in collaboration for energy conservation. Based on the open platform of SEB, we have investigated and evaluated a variety of operation and energy saving control strategies on Carnegie Mellon University Intelligent Work place which is equipped with alternative cooling/heating/ventilation/lighting methods, including radiant mullions, radiant cooling/heating ceiling panels, cool waves, dedicated ventilation unit, motorized window and blinds, and external louvers. Based on the validation results of these control strategies, they were integrated in SEB in a collaborative and dynamic way. This advanced control system was programmed and computer tested with a model of the Intelligent Workplace's northern section (IWn). The advanced control program was then installed in the IWn control system; the performance was measured and compared with that of the state of the art control system to verify the overall energy savings great than 40%. In addition advanced human machine interfaces (HMI's) were developed to communicate both with building

  4. Ervaringen met Advanced Cruise Control (ACC) in een korte praktijkproef.

    OpenAIRE

    Oei, H.-l.

    2003-01-01

    Experiences with Advanced Cruise Control in traffic; a limited experiment. Advanced Cruise Control (ACC) is an ordinary cruise control in which the desired speed is installed manually, but in which the headway time to the vehicle in front is also taken into account. If the headway time becomes less than the installed critical threshold value, the system brakes the vehicle gradually. If the vehicle in front is no longer there, or the headway time is greater than the threshold value, the instal...

  5. Force Control Strategies in Hydraulically Actuated Legged Robots

    Directory of Open Access Journals (Sweden)

    Hector Montes

    2016-03-01

    Full Text Available In this contribution, several strategies of force control have been proposed to be implemented and evaluated in ROBOCLIMBER, a quadruped robot of large dimensions. A first group of strategies proposed in this paper is based on impedance control, which is intended to adapt the foot-ground contact forces according to the experimentally specified damping ratio and the undamped natural frequency. A second control strategy of interest for many practical cases is called the parallel force/position control, which has one inner loop position control and two external control loops, one of force and another of position. A third group of control strategies is the posture stabilization for ROBOCLIMBER using the feedback of the ZMP calculation and the position of its legs. Finally, a control strategy for the control of a quasi-static gait using ZMP feedback is proposed and tested by simulation.

  6. Overview of advanced process control in welding within ERDA

    International Nuclear Information System (INIS)

    The special kinds of demands placed on ERDA weapons and reactors require them to have very reliable welds. Process control is critical in achieving this reliability. ERDA has a number of advanced process control projects underway with much of the emphasis being on electron beam welding. These include projects on voltage measurement, beam-current control, beam focusing, beam spot tracking, spike suppression, and computer control. A general discussion of process control in welding is followed by specific examples of some of the advanced joining process control projects in ERDA

  7. The Effect of Advanced Management Accounting Practices on the Competitive Strategies and Performance

    Directory of Open Access Journals (Sweden)

    Rahmi Yücel

    2015-10-01

    Full Text Available This study is based on a sample of 300 managers from the production industry of West Marmara Region. The goal of this study is to examine the interaction among advanced management accounting practices, competitive strategies and company performance. As a result of study, it is found that advanced accounting management practices have a positive effect on the company performance and competitive strategies. In addition, competitive strategies have an effect on the company performance positively. Furthermore, there is a positive and significant relation between long-term strategy based on management accounting practices and non-financial company performance and between activity based on management accounting practices and financial performance.

  8. Advances in e-health and telemedicine: strategy to bring health service users

    Directory of Open Access Journals (Sweden)

    Wilson Giovanni Jiménez Barbosa

    2015-08-01

    Full Text Available Background: The e-health and telemedicine have emerged as tools to facilitate access to health services, both populations far from the centres, and those who reside near them is not easily accessible or require constant controls by their professionals health traffickers. Objective: To reflect on the uses, progress and difficulties faced by Information and Communication Technologies (ICT as a strategy to bring health services to users. Methodology: qualitative hermeneutic research; advanced in two phases. The first, theoretical review by finding relevant articles in scientific databases. The second phase, critical analysis of literature found, in order to understand the dynamics generated from the use of ICT in the health sector, its current uses and prospected, and the risk that can generate its implementation for providers and patients. Results: The e-health and telemedicine have advanced in their development process andColombiahas not been outside, but there are still drawbacks of ethical, legal and operational order, which are not static and show great variation over time, becoming challenges are not independent but are associated with the dynamic progress of ICT. Conclusion: e-health and telemedicine are valid strategies to improve access to health services to communities. But require the development of processes to prevent, mitigate and / or exceed the inconveniences that may arise from its use. 

  9. Advanced control of propylene polimerizations in slurry reactors

    Directory of Open Access Journals (Sweden)

    Bolsoni A.

    2000-01-01

    Full Text Available The objective of this work is to develop a strategy of nonlinear model predictive control for industrial slurry reactors of propylene polymerizations. The controlled variables are the melt index (polymer quality and the amount of unreacted monomer (productivity. The model used in the controller presents a linear dynamics and a nonlinear static gain given by a neuronal network MLP (multilayer perceptron. The simulated performance of the controller was evaluated for a typical propylene polymerization process. It is shown that the performance of the proposed control strategy is much better than the one obtained with the use of linear predictive controllers for setpoint tracking control problems.

  10. Advanced control of walking-beam reheating furnace

    Institute of Scientific and Technical Information of China (English)

    Zhigang Chen; Chao Xu; Bin Zhang; Huihe Shao; Jianmin Zhang

    2003-01-01

    Reheating furnace is an important device with complex dynamic characteristics in steel plants. The temperature tracing control of reheating furnace has great importance both to the quality of slabs and energy saving. A model-based control strategy,multivariable constrained control (MCC) for the reheating furnace control is used. With this control method, the furnace is treated as a six-input-six-output general model with loops coupled in nature. Compared with the traditional control, the proposed control strategy gets better temperature tracing accuracy and exhibits some energy saving feature. The simulation results show that the performance of the furnace is greatly improved.

  11. Advancing cancer control research in an emerging news media environment.

    Science.gov (United States)

    Smith, Katherine C; Niederdeppe, Jeff; Blake, Kelly D; Cappella, Joseph N

    2013-12-01

    Cancer is both highly feared and highly newsworthy, and there is a robust body of research documenting the content and effects of cancer news coverage on health behaviors and policy. Recent years have witnessed ongoing, transformative shifts in American journalism alongside rapid advances in communication technology and the public information environment. These changes create a pressing need to consider a new set of research questions, sampling strategies, measurement techniques, and theories of media effects to ensure continued relevance and adaptation of communication research to address critical cancer control concerns. This paper begins by briefly reviewing what we know about the role of cancer news in shaping cancer-related beliefs, attitudes, behaviors, and policies. We then outline challenges and opportunities, both theoretical and methodological, posed by the rapidly changing news media environment and the nature of audience engagement. We organize our discussion around three major shifts associated with the emerging news media environment as it relates to health communication: 1) speed and dynamism of news diffusion, 2) increased narrowcasting of media content for specialized audiences, and 3) broadened participation in shaping media content. In so doing, we articulate a set of questions for future theory and research, in an effort to catalyze innovative communication scholarship to improve cancer prevention and control. PMID:24395988

  12. How does a change in the control room design affect diagnostic strategies in nuclear power plants?

    International Nuclear Information System (INIS)

    Recently, main control rooms have been considerably changed by modern computer techniques. Some of the features that distinguish digital control rooms from conventional, analog rooms in nuclear power plants include advanced alarm systems, graphic information display systems, computerized procedure systems, and soft control. These features can bring changes in operator tasks, changing the characteristics of tasks or creating new tasks for operators. It is especially expected that these features may bring out changes in the operator's diagnostic tasks and strategies in a digital control room as compared with an analog control room. This study investigates the differences in the operator's diagnostic tasks and strategies in analog and digital control rooms. This study also attempts to evaluate how new systems in a digital control room affect diagnostic strategies. Three different approaches, which are complementary, are used to identify diagnostic strategies in the digital control room and in the analog control room: (1) observation in the simulator, (2) interview with operators, and (3) a literature review. The results show that the digital control room introduces new diagnosis strategies compared with the analog control room while also changing the characteristics of the strategies, mostly by gaining more support from the computerized system. (author)

  13. Mechanics and model-based control of advanced engineering systems

    CERN Document Server

    Irschik, Hans; Krommer, Michael

    2014-01-01

    Mechanics and Model-Based Control of Advanced Engineering Systems collects 32 contributions presented at the International Workshop on Advanced Dynamics and Model Based Control of Structures and Machines, which took place in St. Petersburg, Russia in July 2012. The workshop continued a series of international workshops, which started with a Japan-Austria Joint Workshop on Mechanics and Model Based Control of Smart Materials and Structures and a Russia-Austria Joint Workshop on Advanced Dynamics and Model Based Control of Structures and Machines. In the present volume, 10 full-length papers based on presentations from Russia, 9 from Austria, 8 from Japan, 3 from Italy, one from Germany and one from Taiwan are included, which represent the state of the art in the field of mechanics and model based control, with particular emphasis on the application of advanced structures and machines.

  14. Advanced Stellar Compass, SAC-C, Interface Control Document

    DEFF Research Database (Denmark)

    Madsen, Peter Buch; Betto, Maurizio; Riis, Troels;

    Interface Control Document for the Advanced Stellar Compass for the SAC-C satellite. The SAC-C is Argentine, Danish and NASA satellite. On the SAC-C satellite there are a simplified version of the Ørsted instrumentation platform. The Advanced Stellar Compass is a improved version of the Ørsted Star...... Imager. This document descibes the interface between the Advanced Stellar Compass and OBDH, the size of the DPU and the Camera etc....

  15. Behavioral Self-Control Strategies for Young Children

    Science.gov (United States)

    Barry, Leasha M.; Haraway, Dana L.

    2005-01-01

    In this paper, self-control strategies are conceptualized as existing on two intersecting continuums of more or less individual control and increasing complexity depending on individual need. Behavioral self-control strategies for young children require external supports to assist children in learning the skills necessary to practice and implement…

  16. Modelling nematode infections in sheep and parasite control strategies

    OpenAIRE

    Laurenson, Yan Christian Stephen Mountfort

    2012-01-01

    Gastrointestinal parasitism in grazing lambs adversely affects animal performance and welfare, causing significant production losses for the sheep industry. Control of gastrointestinal parasitism using chemotherapeutic treatment is under threat due to the emergence of anthelmintic resistance, thus stimulating research into alternative control strategies. Whilst investigating control strategies experimentally can be costly and time consuming, using a mathematical modelling appro...

  17. Predictive Control Strategies Used to Solve Challenges Related to Modern Railway Vehicles

    OpenAIRE

    Ngigi, R. W.; Pislaru, Crinela; Ball, Andrew; Fengshou, Gu; Anyakwo, Arthur

    2011-01-01

    This paper is an attempt to collate and critically appraise the recent advances in control strategies used to solve challenges related to railway vehicles which present nonlinearities and uncertainties. These strategies concentrate on stability of solid axle-wheelsets, guidance for wheelsets to provide the function of track following and curving to reduce all unnecessary creep forces and associated wear/noise. The focus is on active primary and secondary suspensions, braking and trac...

  18. Strategies for reactive power control in wind farms with STATCOM

    OpenAIRE

    Díaz González, Francisco; Martínez Rojas, Marcela; Sumper, Andreas; Gomis Bellmunt, Oriol

    2010-01-01

    This paper presents three strategies for reactive power control in wind farms with STATCOM. First, the STATCOM system and its applications in electric power systems and wind farms are shown. Second, the modeling done of the wind farm, the STATCOM and the network are presented. Finally, control strategies for reactive power delivered by the park to the network when required are shown. The result of the implementation of each control strategy is shown by simulation.

  19. Advanced Combustion and Emission Control Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

  20. Motion control in advanced driving simulators

    OpenAIRE

    Elloumi, Hatem

    2006-01-01

    Driving simulators are advanced devices composed of four components: a virtual scene projected on a wide screen to imitate the road and the traffic, an audio system to play the driving sounds (horn, squeal of brakes, etc.), a car cockpit (including a real dashboard, the pedals and the seat of the driver) to copy the body position and the interaction of the driver with a real vehicle and finally a robot carrying the car cockpit to provide its motion. While the first three components could be c...

  1. Model-free adaptive control of advanced power plants

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, George Shu-Xing; Mulkey, Steven L.; Wang, Qiang

    2015-08-18

    A novel 3-Input-3-Output (3.times.3) Model-Free Adaptive (MFA) controller with a set of artificial neural networks as part of the controller is introduced. A 3.times.3 MFA control system using the inventive 3.times.3 MFA controller is described to control key process variables including Power, Steam Throttle Pressure, and Steam Temperature of boiler-turbine-generator (BTG) units in conventional and advanced power plants. Those advanced power plants may comprise Once-Through Supercritical (OTSC) Boilers, Circulating Fluidized-Bed (CFB) Boilers, and Once-Through Supercritical Circulating Fluidized-Bed (OTSC CFB) Boilers.

  2. Fuzzy Control Strategies in Human Operator and Sport Modeling

    CERN Document Server

    Ivancevic, Tijana T; Markovic, Sasa

    2009-01-01

    The motivation behind mathematically modeling the human operator is to help explain the response characteristics of the complex dynamical system including the human manual controller. In this paper, we present two different fuzzy logic strategies for human operator and sport modeling: fixed fuzzy-logic inference control and adaptive fuzzy-logic control, including neuro-fuzzy-fractal control. As an application of the presented fuzzy strategies, we present a fuzzy-control based tennis simulator.

  3. Strategy to Promote Active Learning of an Advanced Research Method

    Science.gov (United States)

    McDermott, Hilary J.; Dovey, Terence M.

    2013-01-01

    Research methods courses aim to equip students with the knowledge and skills required for research yet seldom include practical aspects of assessment. This reflective practitioner report describes and evaluates an innovative approach to teaching and assessing advanced qualitative research methods to final-year psychology undergraduate students. An…

  4. Effects of Narrative Script Advance Organizer Strategies Used to Introduce Video in the Foreign Language Classroom

    Science.gov (United States)

    Ambard, Philip D.; Ambard, Linda K.

    2012-01-01

    The study compared participant comprehension of foreign language video content using two advance organizer (AO) strategies while exploring the benefits of AOs as proficiency increases. Participants were 50 advanced-beginner Spanish college students in three sections. Collaborative reading condition participants read a target language narrative…

  5. Fuzzy-like PD controller for spatial control of advanced heavy water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Londhe, P.S., E-mail: pandurangl97@gmail.com [Research Scholar, SGGS Institute of Engineering and Technology, Vishnupuri, Nanded 431606 (India); Patre, B.M., E-mail: bmpatre@ieee.org [Department of Instrumentation Engineering, Shri Guru Gobind Singhji Institute of Engineering and Technology, Vishnupuri, Nanded 431 606 (India); Tiwari, A.P., E-mail: aptiwari@barc.gov.in [Reactor Control Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

    2014-07-01

    Highlights: • Highly non-linear model of AHWR is used for spatial power control. • A simple fuzzy-like PD (FZ-PD) control structure with robust rule base is developed. • Robust rule structure reduces the difficulties in design and tuning of controller. • Proposed FZ-PD structure shows robust and better transient performance. • Proposed FZ-PD controller is able to suppress spatial oscillations in AHWR. - Abstract: Spatial oscillations in the neutron flux distribution due to xenon reactivity feedback requires stringent control in large nuclear reactors, like advanced heavy water reactor (AHWR). If the spatial oscillations in the power distribution are not controlled, power density and rate of change of power at some locations in the reactor core may exceed limits of fuel failure due to ‘flux tilting’. Further, situations such as on-line refueling might cause transient variations in flux-shape from the nominal flux-shape. For analysis and control of spatial oscillations in AHWR, it is necessary to design a suitable control strategy, which will stabilize these oscillations. In this paper, a simplified scheme to design a conventional fuzzy logic controller for spatial control of AHWR is presented. This scheme known as fuzzy-like proportional derivative (FZ-PD) controller, uses robust PD (proportional derivative) type rule base. Due to robust rule base structure, tuning of scaling factors is greatly reduced. The non-linear coupled core neutronics-thermal hydraulics model of AHWR considered here represented by 90 first order differential equations. Through the dynamic simulations, it is observed that the designed FZ-PD controller is able to suppress spatial oscillations developed in AHWR and its performance is found to be robust.

  6. Advanced Unit Commitment Strategies for the U.S. Eastern Interconnection: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ela, E.; Milligan, M.; Meibom, P.; Barth, R.; Tuohy, A.

    2010-10-01

    This paper outlines a study undertaken for the U.S. Eastern Interconnection in which different advanced unit commitment strategies were simulated for three different years to evaluate the benefits that may occur from using these strategies as an operational tool.

  7. Cooperative research for human factors review of advanced control rooms

    International Nuclear Information System (INIS)

    This project has been performed as cooperative research between KAERI and USNRC. Human factors issues related to soft controls, which is one of key features of advanced HSI, are identified in this project. The issues are analyzed for the evaluation approaches in either experimental or analytical ways. Also, issues requiring additional researches for the evaluation of advanced HSI are identified in the areas of advanced information systems design, computer-based procedure systems, soft controls, human systems interface and plant modernization process, and maintainability of digital systems. The issues are analyzed to discriminate the urgency of researches on it to high, medium, and low levels in consideration of advanced HSI development status in Korea, and some of the issues that can be handled by experimental researches are identified. Additionally, an experimental study is performed to compare operator's performance on human error detection in advanced control rooms vs. in conventional control rooms. It is found that advanced control rooms have several design characteristics hindering operator's error detection performance compared to conventional control rooms

  8. English Language Learning Strategies Reported by Advanced Language Learners

    Science.gov (United States)

    Lee, Juyeon; Heinz, Michael

    2016-01-01

    The purpose of the present study is to investigate effective English language learning strategies (LLSs) employed by successful language learners. The participants in this study were 20 student interpreters enrolled in the graduate school of interpretation and translation in Korea. Data on LLSs were collected through unstructured essay writing, a…

  9. Advanced Simulation and Computing Co-Design Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Ang, James A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hoang, Thuc T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kelly, Suzanne M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McPherson, Allen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neely, Rob [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-11-01

    This ASC Co-design Strategy lays out the full continuum and components of the co-design process, based on what we have experienced thus far and what we wish to do more in the future to meet the program’s mission of providing high performance computing (HPC) and simulation capabilities for NNSA to carry out its stockpile stewardship responsibility.

  10. Advanced mobile networking, sensing, and controls.

    Energy Technology Data Exchange (ETDEWEB)

    Feddema, John Todd; Kilman, Dominique Marie; Byrne, Raymond Harry; Young, Joseph G.; Lewis, Christopher L.; Van Leeuwen, Brian P.; Robinett, Rush D. III; Harrington, John J.

    2005-03-01

    This report describes an integrated approach for designing communication, sensing, and control systems for mobile distributed systems. Graph theoretic methods are used to analyze the input/output reachability and structural controllability and observability of a decentralized system. Embedded in each network node, this analysis will automatically reconfigure an ad hoc communication network for the sensing and control task at hand. The graph analysis can also be used to create the optimal communication flow control based upon the spatial distribution of the network nodes. Edge coloring algorithms tell us that the minimum number of time slots in a planar network is equal to either the maximum number of adjacent nodes (or degree) of the undirected graph plus some small number. Therefore, the more spread out that the nodes are, the fewer number of time slots are needed for communication, and the smaller the latency between nodes. In a coupled system, this results in a more responsive sensor network and control system. Network protocols are developed to propagate this information, and distributed algorithms are developed to automatically adjust the number of time slots available for communication. These protocols and algorithms must be extremely efficient and only updated as network nodes move. In addition, queuing theory is used to analyze the delay characteristics of Carrier Sense Multiple Access (CSMA) networks. This report documents the analysis, simulation, and implementation of these algorithms performed under this Laboratory Directed Research and Development (LDRD) effort.

  11. Grid Monitoring and Advanced Control of Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Timbus, Adrian Vasile

    of controllers have been studied and compared. The possibility of using the information about grid variables into the control structure in order to improve the control of DPGS has also been investigated. As a consequence, improved behavior of resonant controller has been noticed if grid frequency information...... is forwarded to its internal model. Additionally, controllers such as dead beat and hysteresis controller improve their robustness to parameter mismatch if the identi ed value of grid impedance is passed to the controller. Moreover, several control strategies to provide exible active and reactive power control...

  12. Short Horizon Control Strategies for an Alternating Activated Sludge Process

    DEFF Research Database (Denmark)

    Isaacs, Steven Howard

    1996-01-01

    Three control strategies allowing improved operational flexibility of an alternating type activated sludge process are presented in a unified model based framework. The control handles employed are the addition rate of an external carbon source to denitrification, the cycle length...

  13. A fault tolerant superheat control strategy for supermarket refrigeration systems

    DEFF Research Database (Denmark)

    Vinther, Kasper; Izadi-Zamanabadi, Roozbeh; Rasmussen, Henrik;

    2013-01-01

    In this paper, a fault tolerant control (FTC) strategy is proposed for evaporator superheat control in supermarket refrigeration systems. Conventional control uses a pressure and temperature sensor for this purpose, however, the pressure sensor can fail to function. A contingency control strategy......, based on a maximum slope-seeking control method and only a single temperature sensor, is developed to drive the evaporator outlet temperature to a level that gives a suitable superheat of the refrigerant. The FTC strategy requires no a priori system knowledge or additional hardware and functions...... system....

  14. Human factors survey of advanced instrumentation and controls

    International Nuclear Information System (INIS)

    A survey oriented towards identifying the human factors issues in regard to the use of advanced instrumentation and controls (I ampersand C) in the nuclear industry was conducted. A number of United States (US) and Canadian nuclear vendors and utilities were participants in the survey. Human factors items, subsumed under the categories of computer-generated displays (CGD), controls, organizational support, training, and related topics, were discussed. The survey found the industry to be concerned about the human factors issues related to the implementation of advanced I ampersand C. Fifteen potential human factors problems were identified. They include: the need for an advanced I ampersand C guideline equivalent to NUREG-0700; a role change in the control room from operator to supervisor; information overload; adequacy of existing training technology for advanced I ampersand C; and operator acceptance and trust. 11 refs., 1 tab

  15. Guest Editorial Special Issue on Recent Advances and New Directions in Switched Control Systems

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ As guest editors, it is our great honor to bring this special issue of the Journal of Control Theory and Applications devoted to Recent Advances and New Directions in Switched Control Systems. Recently, switched control systems have attracted much attention in the control systems community. Problems in this area are not only academically challenging for the inherent mathematical complexity, but also are derived or motivated from advanced applications in natural sciences, engineering, and social sciences. For survival, natural biological systems switch their survival strategies in accordance with environmental changes. For improved performance, switching has been extensively utilized/exploited in engineering systems such as automotive drive train control, electronic devices, control of power systems, etc.

  16. Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices

    Energy Technology Data Exchange (ETDEWEB)

    McEntee, Jarlath [Ocean Renewable Power Company, Portland, ME (United States); Polagye, Brian [Ocean Renewable Power Company, Portland, ME (United States); Fabien, Brian [Ocean Renewable Power Company, Portland, ME (United States); Thomson, Jim [Ocean Renewable Power Company, Portland, ME (United States); Kilcher, Levi [Ocean Renewable Power Company, Portland, ME (United States); Marnagh, Cian [Ocean Renewable Power Company, Portland, ME (United States); Donegan, James [Ocean Renewable Power Company, Portland, ME (United States)

    2016-03-31

    The Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices (Project) investigated, analyzed and modeled advanced turbine control schemes with the objective of increasing the energy harvested by hydrokinetic turbines in turbulent flow. Ocean Renewable Power Company (ORPC) implemented and validated a feedforward controller to increase power capture; and applied and tested the controls on ORPC’s RivGen® Power Systems in Igiugig, Alaska. Assessments of performance improvements were made for the RivGen® in the Igiugig environment and for ORPC’s TidGen® Power System in a reference tidal environment. Annualized Energy Production (AEP) and Levelized Cost of Energy (LCOE) improvements associated with implementation of the recommended control methodology were made for the TidGen® Power System in the DOE reference tidal environment. System Performance Advancement (SPA) goals were selected for the project. SPA targets were to improve Power to Weight Ratio (PWR) and system Availability, with the intention of reducing Levelized Cost of Electricity (LCOE). This project focused primarily reducing in PWR. Reductions in PWR of 25.5% were achieved. Reductions of 20.3% in LCOE were achieved. This project evaluated four types of controllers which were tested in simulation, emulation, a laboratory flume, and the field. The adaptive Kω2 controller performs similarly to the non-adaptive version of the same controller and may be useful in tidal channels where the mean velocity is continually evolving. Trends in simulation were largely verified through experiments, which also provided the opportunity to test assumptions about turbine responsiveness and control resilience to varying scales of turbulence. Laboratory experiments provided an essential stepping stone between simulation and implementation on a field-scale turbine. Experiments also demonstrated that using “energy loss” as a metric to differentiate between well-designed controllers operating at

  17. Advanced Stellar Compass, CHAMP, Interface Control Document

    DEFF Research Database (Denmark)

    Madsen, Peter Buch; Jørgensen, John Leif; Betto, Maurizio;

    1999-01-01

    The German government research establishment "GeoForschungsZentrum" developed under a contract to the German government a microsatellite named "Champ". The Space Instrumentation Group has made a Interface Control Document for the CHAMP, witch describes the Star Imager, the electrical interface, t...

  18. Simulation of advanced concepts for damage control

    NARCIS (Netherlands)

    Gillis, M.P.W.; Keijer, W.; Smit, C.S.; Wolff, P.A.

    2003-01-01

    Damage control on board navy ships requires a lot of manpower. On a frigate-sized ship of the Royal Netherlands Navy, up to ninety people can be involved in tasks like fire fighting, battle damage repair and treatment of casualties. In present times this is no longer attainable or affordable. To red

  19. Advanced Control Techniques for WEC Wave Dragon

    DEFF Research Database (Denmark)

    Tedd, James; Kofoed, Jens Peter; Jasinski, M.;

    2007-01-01

    This paper presents the ongoing work on control of the Wave Dragon wave energy converter. Research is being conducted in and between several centers across Europe. This is building upon the knowledge gained in the prototype project, and will enable much better performance of the future deployment...... of the full scale Wave Dragon....

  20. Advanced Control Techniques for WEC Wave Dragon

    OpenAIRE

    Tedd, James; Kofoed, Jens Peter; Jasinski, M; Morris, A.; Friis-Madsen, E.; Wisniewski, Rafal; Bendtsen, Jan Dimon

    2007-01-01

      This paper presents the ongoing work on control of the Wave Dragon wave energy converter. Research is being conducted in and between several centers across Europe. This is building upon the knowledge gained in the prototype project, and will enable much better performance of the future deployment of the full scale Wave Dragon.

  1. Recent Advances in Bidirectional Modeling and Structural Control

    OpenAIRE

    Paul, Satyam; Yu, Wen; Li, Xiaoou

    2016-01-01

    This paper provides an overview of building structure modeling and control under bidirectional seismic waves. It focuses on different types of bidirectional control devices, control strategies, and bidirectional sensors used in structural control systems. This paper also highlights the various issues like system identification techniques, the time-delay in the system, estimation of velocity and position from acceleration signals, and optimal placement of the sensors and control devices. The i...

  2. Recent Advances in Bidirectional Modeling and Structural Control

    OpenAIRE

    Satyam Paul; Wen Yu; Xiaoou Li

    2016-01-01

    This paper provides an overview of building structure modeling and control under bidirectional seismic waves. It focuses on different types of bidirectional control devices, control strategies, and bidirectional sensors used in structural control systems. This paper also highlights the various issues like system identification techniques, the time-delay in the system, estimation of velocity and position from acceleration signals, and optimal placement of the sensors and control devices. Th...

  3. Public authority control strategy for opinion evolution in social networks

    Science.gov (United States)

    Chen, Xi; Xiong, Xi; Zhang, Minghong; Li, Wei

    2016-08-01

    This paper addresses the need to deal with and control public opinion and rumors. Existing strategies to control public opinion include degree, random, and adaptive bridge control strategies. In this paper, we use the HK model to present a public opinion control strategy based on public authority (PA). This means utilizing the influence of expert or high authority individuals whose opinions we control to obtain the optimum effect in the shortest time possible and thus reach a consensus of public opinion. Public authority (PA) is only influenced by individuals' attributes (age, economic status, and education level) and not their degree distribution; hence, in this paper, we assume that PA complies with two types of public authority distribution (normal and power-law). According to the proposed control strategy, our experiment is based on random, degree, and public authority control strategies in three different social networks (small-world, scale-free, and random) and we compare and analyze the strategies in terms of convergence time (T), final number of controlled agents (C), and comprehensive efficiency (E). We find that different network topologies and the distribution of the PA in the network can influence the final controlling effect. While the effect of PA strategy differs in different network topology structures, all structures achieve comprehensive efficiency with any kind of public authority distribution in any network. Our findings are consistent with several current sociological phenomena and show that in the process of public opinion/rumor control, considerable attention should be paid to high authority individuals.

  4. Elements of an advanced integrated operator control station

    International Nuclear Information System (INIS)

    One of the critical determinants of peformance for any remotely operated maintenance system is the compatibility achieved between elements of the man/machine interface (e.g., master manipulator controller, controls, displays, etc.) and the human operator. In the Remote Control Engineering task of the Consolidated Fuel Reprocessing Program, considerable attention has been devoted to optimizing the man/machine interface of the operator control station. This system must be considered an integral element of the overall maintenance work system which includes transporters, manipulators, remote viewing, and other parts. The control station must reflect the integration of the operator team, control/display panels, manipulator master controllers, and remote viewing monitors. Human factors principles and experimentation have been used in the development of an advanced integrated operator control station designed for the advance servomanipulator. Key features of this next-generation design are summarized in this presentation. 7 references, 4 figures

  5. 40 CFR 52.573 - Control strategy: General.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: General. 52.573... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Georgia> § 52.573 Control strategy: General. The generic rules and procedures for emission trades (bubbles), submitted on October 27, 1982, by...

  6. 40 CFR 52.378 - Control strategy: PM10

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: PM10 52.378 Section 52.378 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Connecticut § 52.378 Control strategy: PM10 (a)...

  7. 40 CFR 52.58 - Control strategy: Lead.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Lead. 52.58 Section 52.58 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.58 Control strategy: Lead. The lead...

  8. 40 CFR 52.350 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.350 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Colorado § 52.350 Control strategy: Ozone. (a) Revisions to the Colorado State Implementation Plan, 1-hour ozone NAAQS Redesignation Request and...

  9. 40 CFR 52.582 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... satisfies 40 CFR 58.20(f) which requires the State to provide for the establishment and maintenance of... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.582 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Georgia> § 52.582 Control strategy: Ozone. (a)...

  10. 40 CFR 52.930 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.930 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Kentucky § 52.930 Control strategy: Ozone. (a) The VOC..., Campbell and Kenton Counties) ozone nonattainment area. The demonstration of attainment of the...

  11. 40 CFR 52.476 - Control strategy: ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: ozone. 52.476 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS District of Columbia § 52.476 Control strategy: ozone. (a... of Progress Plan for the District of Columbia's portion of the Metropolitan Washington, D.C....

  12. 40 CFR 52.66 - Control Strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control Strategy: Ozone. 52.66 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.66 Control Strategy: Ozone. (a) The redesignation request submitted by the State of Alabama, on March 16, 1995 for the Birmingham marginal...

  13. 40 CFR 52.377 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.377 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Connecticut § 52.377 Control strategy: Ozone. (a... requirements of sections 172(c)(9) and 182(c)(9) of the Clean Air Act, for the Greater Hartford serious...

  14. 40 CFR 52.65 - Control Strategy: Nitrogen oxides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control Strategy: Nitrogen oxides. 52... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Alabama § 52.65 Control Strategy: Nitrogen oxides. On October 22, 1990, the Alabama Department of Environmental Management submitted a revision...

  15. 40 CFR 52.1375 - Control strategy: Lead.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Lead. 52.1375 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Montana § 52.1375 Control strategy: Lead. Determination—EPA has determined that the East Helena Lead nonattainment area has attained the lead...

  16. 40 CFR 52.2236 - Control strategy; lead.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy; lead. 52.2236 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Tennessee § 52.2236 Control strategy; lead... on October 6, 1994. These revisions address the requirements necessary to change a lead...

  17. 40 CFR 52.1681 - Control strategy: Lead.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Lead. 52.1681 Section...) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) New York § 52.1681 Control strategy: Lead. As part of the attainment demonstration for lead, the State of New York has committed to rate all...

  18. 40 CFR 52.2429 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ....5 NAAQS has attained the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 52.1004(c... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January...

  19. 40 CFR 52.2526 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... NAAQS. These determinations, in accordance with 40 CFR 52.1004(c), suspend the requirements for these... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal...

  20. 40 CFR 52.1131 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1131 Section 52.1131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Revisions to the following regulations submitted on March...

  1. 40 CFR 52.1374 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted...

  2. Advances in Computer, Communication, Control and Automation

    CERN Document Server

    011 International Conference on Computer, Communication, Control and Automation

    2012-01-01

    The volume includes a set of selected papers extended and revised from the 2011 International Conference on Computer, Communication, Control and Automation (3CA 2011). 2011 International Conference on Computer, Communication, Control and Automation (3CA 2011) has been held in Zhuhai, China, November 19-20, 2011. This volume  topics covered include signal and Image processing, speech and audio Processing, video processing and analysis, artificial intelligence, computing and intelligent systems, machine learning, sensor and neural networks, knowledge discovery and data mining, fuzzy mathematics and Applications, knowledge-based systems, hybrid systems modeling and design, risk analysis and management, system modeling and simulation. We hope that researchers, graduate students and other interested readers benefit scientifically from the proceedings and also find it stimulating in the process.

  3. Advances in Future Computer and Control Systems v.2

    CERN Document Server

    Lin, Sally; 2012 International Conference on Future Computer and Control Systems(FCCS2012)

    2012-01-01

    FCCS2012 is an integrated conference concentrating its focus on Future Computer and Control Systems. “Advances in Future Computer and Control Systems” presents the proceedings of the 2012 International Conference on Future Computer and Control Systems(FCCS2012) held April 21-22,2012, in Changsha, China including recent research results on Future Computer and Control Systems of researchers from all around the world.

  4. Advances in Future Computer and Control Systems v.1

    CERN Document Server

    Lin, Sally; 2012 International Conference on Future Computer and Control Systems(FCCS2012)

    2012-01-01

    FCCS2012 is an integrated conference concentrating its focus on Future Computer and Control Systems. “Advances in Future Computer and Control Systems” presents the proceedings of the 2012 International Conference on Future Computer and Control Systems(FCCS2012) held April 21-22,2012, in Changsha, China including recent research results on Future Computer and Control Systems of researchers from all around the world.

  5. Global lessons from Nigeria's ebolavirus control strategy.

    Science.gov (United States)

    Elemuwa, Chris; Kutalek, Ruth; Ali, Mohammad; Mworozi, Edison; Kochhar, Sonali; Rath, Barbara

    2015-01-01

    The current Ebola virus disease outbreak challenged medical and public health systems in West Africa. In Nigeria, the existing infrastructure of the polio surveillance system was leveraged rapidly to contain the spread of Ebola virus. We highlight important lessons learnt from the successful implementation of Ebola virus disease surveillance strategies, which should be amplified further to prepare the ground for successful vaccination programs. Close collaboration between national and international stakeholders as well as public/private partnerships will be instrumental in future Ebola virus immunization strategies. PMID:26190046

  6. Gas-phase advanced oxidation for effective, efficient in situ control of pollution

    DEFF Research Database (Denmark)

    Johnson, Matthew Stanley; Nilsson, Elna Johanna Kristina; Svensson, Erik Anders;

    2014-01-01

    In this article, gas-phase advanced oxidation, a new method for pollution control building on the photo-oxidation and particle formation chemistry occurring in the atmosphere, is introduced and characterized. The process uses ozone and UV-C light to produce in situ radicals to oxidize pollution...... on these results, in situ gas-phase advanced oxidation is a viable control strategy for most volatile organic compounds, specifically those with a OH* reaction rate higher than ca. 5 × 10-13 cm3/s. Gas-phase advanced oxidation is able to remove compounds that react with OH and to control ozone and total...... particulate mass. Secondary pollution including formaldehyde and ultrafine particles might be generated, depending on the composition of the primary pollution. © 2014 American Chemical Society....

  7. New control strategies for neuroprosthetic systems

    NARCIS (Netherlands)

    Crago, Patrick E.; Lan, Ning; Veltink, Peter H.; Abbas, James J.; Kantor, Carole

    1996-01-01

    The availability of techniques to artificially excite paralyzed muscles opens enormous potential for restoring both upper and lower extremity movements with neuroprostheses. Neuroprostheses must stimulate muscle, and control and regulate the artificial movements produced. Control methods to accompli

  8. Advances in pharmacological strategies for the prevention of cataract development

    Directory of Open Access Journals (Sweden)

    Gupta S

    2009-01-01

    Full Text Available Cataractous-opacification of the lens is one of the leading causes of blindness in India. The situation can be managed by surgical removal of the cataractous lens. Various pharmacological strategies have been proposed for the prevention and treatment of cataract. Information on possible benefits of putative anticataract agents comes from a variety of approaches, ranging from laboratory experiments, both in vitro and in vivo , to epidemiological studies in patients. This review deals with the various mechanisms, and possible pharmacological interventions for the prevention of cataract. The article also reviews research on potential anticataractous agents, including aldose reductase inhibitors, glutathione boosters, antiglycating agents, vitamins and various drugs from indigenous sources.

  9. Control strategies for active lower extremity prosthetics and orthotics: a review

    OpenAIRE

    Tucker, M R; Olivier, J; Pagel, A; Bleuler, H.; Bouri, M.; Lambercy, O.; del R. Millan, J.; Riener, R.; Vallery, H; Gassert, R.

    2015-01-01

    Technological advancements have led to the development of numerous wearable robotic devices for the physical assistance and restoration of human locomotion. While many challenges remain with respect to the mechanical design of such devices, it is at least equally challenging and important to develop strategies to control them in concert with the intentions of the user. This work reviews the state-of-the-art techniques for controlling portable active lower limb prosthetic and orthotic (P/O) de...

  10. Practical Implementations of Advanced Process Control for Linear Systems

    DEFF Research Database (Denmark)

    Knudsen, Jørgen K . H.; Huusom, Jakob Kjøbsted; Jørgensen, John Bagterp

    This paper describes some practical problems encountered, when implementing Advanced Process Control, APC, schemes on linear processes. The implemented APC controllers discussed will be LQR, Riccati MPC and Condensed MPC controllers illustrated by simulation of the Four Tank Process and a lineari...... on pilot plant equipment on the department of Chemical Engineering DTU Lyngby.......This paper describes some practical problems encountered, when implementing Advanced Process Control, APC, schemes on linear processes. The implemented APC controllers discussed will be LQR, Riccati MPC and Condensed MPC controllers illustrated by simulation of the Four Tank Process...... cannot be achieved without violation of process constraints. A target calculation function can be used to calculate the optimal achievable target for the process. The use of hard and soft constraints for process input constraints in the MPC controllers, ensures feasible solutions. The computational load...

  11. An extended signal control strategy for urban network traffic flow

    Science.gov (United States)

    Yan, Fei; Tian, Fuli; Shi, Zhongke

    2016-03-01

    Traffic flow patterns are in general repeated on a daily or weekly basis. To improve the traffic conditions by using the inherent repeatability of traffic flow, a novel signal control strategy for urban networks was developed via iterative learning control (ILC) approach. Rigorous analysis shows that the proposed learning control method can guarantee the asymptotic convergence. The impacts of the ILC-based signal control strategy on the macroscopic fundamental diagram (MFD) were analyzed by simulations on a test road network. The results show that the proposed ILC strategy can evenly distribute the accumulation in the network and improve the network mobility.

  12. Recent Advances in Means Safety as a Suicide Prevention Strategy.

    Science.gov (United States)

    Jin, Hyejin M; Khazem, Lauren R; Anestis, Michael D

    2016-10-01

    Despite advances in theory and the development and implementation of evidence-based treatments, the United States suicide rate has been rising continuously for over a decade. Although this does not indicate that traditional treatment approaches should be abandoned, it does highlight the need to supplement such approaches with alternatives. One seemingly highly valuable option is means safety, defined as the reduced access to and/or increased safe storage of potentially lethal methods for suicide. This paper provides a review of the current literature on the prevalence of six methods for suicide and preventative efforts aimed to reduce suicide rates. The majority of means safety interventions seem promising given that these methods are common and highly lethal. However, cultural and practical barriers will need to be taken into consideration when implementing these plans. Overall, means safety efforts and preventative measures seem to be promising ways to reduce the national suicide rate if implemented.

  13. Advanced control room evaluation: General approach and rationale

    Energy Technology Data Exchange (ETDEWEB)

    O' Hara, J.M. (Brookhaven National Lab., Upton, NY (USA)); Wachtel, J. (Nuclear Regulatory Commission, Washington, DC (USA))

    1991-01-01

    Advanced control rooms (ACRs) for future nuclear power plants (NPPs) are being designed utilizing computer-based technologies. The US Nuclear Regulatory Commission reviews the human engineering aspects of such control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported in order to protect public health and safety. This paper describes the rationale and general approach to the development of a human factors review guideline for ACRs. The factors influencing the guideline development are discussed, including the review environment, the types of advanced technologies being addressed, the human factors issues associated with advanced technology, and the current state-of-the-art of human factors guidelines for advanced human-system interfaces (HSIs). The proposed approach to ACR review would track the design and implementation process through the application of review guidelines reflecting four review modules: planning, design process analysis, human factors engineering review, and dynamic performance evaluation. 21 refs.

  14. Advances in strategies and methodologies in cancer immunotherapy.

    Science.gov (United States)

    Lam, Samuel S K; Zhou, Feifan; Hode, Tomas; Nordquist, Robert E; Alleruzzo, Luciano; Raker, Joseph; Chen, Wei R

    2015-04-01

    Since the invention of Coley's toxin by William Coley in early 1900s, the path for cancer immunotherapy has been a convoluted one. Although still not considered standard of care, with the FDA approval of trastuzumab, Provenge and ipilimumab, the medical and scientific community has started to embrace the possibility that immunotherapy could be a new hope for cancer patients with otherwise untreatable metastatic diseases. This review aims to summarize the development of some major strategies in cancer immunotherapy, from the earliest peptide vaccine and transfer of tumor specific antibodies/T cells to the more recent dendritic cell (DC) vaccines, whole cell tumor vaccines, and checkpoint blockade therapy. Discussion of some major milestones and obstacles in the shaping of the field and the future perspectives is included. Photoimmunotherapy is also reviewed as an example of emerging new therapies combining phototherapy and immunotherapy.

  15. Adaptive Landing Gear: Optimum Control Strategy and Potential for Improvement

    OpenAIRE

    Grzegorz Mikułowski; Łukasz Jankowski

    2009-01-01

    An adaptive landing gear is a landing gear (LG) capable of active adaptation to particular landing conditions by means of controlled hydraulic force. The objective of the adaptive control is to mitigate the peak force transferred to the aircraft structure during touch-down, and thus to limit the structural fatigue factor. This paper investigates the ultimate limits for improvement due to various strategies of active control. Five strategies are proposed and investigated numerically using a~va...

  16. Backstepping Strategy for Induction Motor Control

    DEFF Research Database (Denmark)

    Rasmussen, Henrik; Vadstrup, P.; Børsting, H.

    2000-01-01

    Using backstepping, which is a recursive nonlinear design method, a novel approach to control of induction motors is developed. The resulting scheme leads to a nonlinear controller for the torque and the amplitude of the field. A combination of nonlinear damping and observer backstepping with a s......Using backstepping, which is a recursive nonlinear design method, a novel approach to control of induction motors is developed. The resulting scheme leads to a nonlinear controller for the torque and the amplitude of the field. A combination of nonlinear damping and observer backstepping...

  17. Backstepping Strategy for Induction Motor Control

    DEFF Research Database (Denmark)

    Rasmussen, Henrik; Vadstrup, P.; Børsting, H.

    2000-01-01

    Using backstepping, which is a recursive nonlinear design method, a novel approach to control of induction motors is developed. The resulting scheme leads to a nonlinear controller for the torque and the amplitude of the field. A combination of nonlinear damping and observer backstepping...... with a simple flux observer is used in the design. Assuming known motor parameters the design achieves stability with guaranteed region of attraction. It is also shown how a conventional field oriented controller may be obtained by omitting parts of the nonlinear controller....

  18. Advanced control systems research at UPC Terrassa Campus

    OpenAIRE

    Quevedo Casín, Joseba Jokin; Puig Cayuela, Vicenç

    2013-01-01

    Advanced Control Systems (SAC) is a multidiscip linary research group involving UPC professors and Spanish National Research Council (CSIC) researchers, focused on the wide subject of control and supervision of dynamic systems. The group uses theory of signal/systems tools, modelling, simulation and optimization in order to face real problems of systems and automated processes, specifically in the next subjects: Optimal/predictive control of large scale systems (mainly related with water cycl...

  19. Recent Advances in Explicit Multiparametric Nonlinear Model Predictive Control

    KAUST Repository

    Domínguez, Luis F.

    2011-01-19

    In this paper we present recent advances in multiparametric nonlinear programming (mp-NLP) algorithms for explicit nonlinear model predictive control (mp-NMPC). Three mp-NLP algorithms for NMPC are discussed, based on which novel mp-NMPC controllers are derived. The performance of the explicit controllers are then tested and compared in a simulation example involving the operation of a continuous stirred-tank reactor (CSTR). © 2010 American Chemical Society.

  20. Strategy Guideline. Advanced Construction Documentation Recommendations for High Performance Homes

    Energy Technology Data Exchange (ETDEWEB)

    Lukachko, A. [Building Science Corporation, Somerville, MA (United States); Gates, C. [Building Science Corporation, Somerville, MA (United States); Straube, J. [Building Science Corporation, Somerville, MA (United States)

    2011-12-01

    As whole house energy efficiency increases, new materials and new systems require greater coordination and communication between industry stakeholders. This report presents four changes that are recommended to achieve improvements in energy efficiency, durability and health in Building America houses: create coordination drawings, improve specifications, improve detail drawings, and review drawings and prepare a Quality Control Plan.

  1. Strategy optimization for controlled Markov process with descriptive complexity constraint

    Institute of Scientific and Technical Information of China (English)

    JIA QingShan; ZHAO QianChuan

    2009-01-01

    Due to various advantages in storage and Implementation,simple strategies are usually preferred than complex strategies when the performances are close.Strategy optimization for controlled Markov process with descriptive complexity constraint provides a general framework for many such problems.In this paper,we first show by examples that the descriptive complexity and the performance of a strategy could be Independent,and use the F-matrix in the No-Free-Lunch Theorem to show the risk that approximating complex strategies may lead to simple strategies that are unboundedly worse in cardinal performance than the original complex strategies.We then develop a method that handles the descriptive complexity constraint directly,which describes simple strategies exactly and only approximates complex strategies during the optimization.The ordinal performance difference between the resulting strategies of this selective approximation method and the global optimum is quantified.Numerical examples on an engine maintenance problem show how this method Improves the solution quality.We hope this work sheds some insights to solving general strategy optimization for controlled Markov procase with descriptive complexity constraint.

  2. Experimental and computing strategies in advanced material characterization problems

    Science.gov (United States)

    Bolzon, G.

    2015-10-01

    The mechanical characterization of materials relies more and more often on sophisticated experimental methods that permit to acquire a large amount of data and, contemporarily, to reduce the invasiveness of the tests. This evolution accompanies the growing demand of non-destructive diagnostic tools that assess the safety level of components in use in structures and infrastructures, for instance in the strategic energy sector. Advanced material systems and properties that are not amenable to traditional techniques, for instance thin layered structures and their adhesion on the relevant substrates, can be also characterized by means of combined experimental-numerical tools elaborating data acquired by full-field measurement techniques. In this context, parameter identification procedures involve the repeated simulation of the laboratory or in situ tests by sophisticated and usually expensive non-linear analyses while, in some situation, reliable and accurate results would be required in real time. The effectiveness and the filtering capabilities of reduced models based on decomposition and interpolation techniques can be profitably used to meet these conflicting requirements. This communication intends to summarize some results recently achieved in this field by the author and her co-workers. The aim is to foster further interaction between engineering and mathematical communities.

  3. Experimental and computing strategies in advanced material characterization problems

    Energy Technology Data Exchange (ETDEWEB)

    Bolzon, G. [Department of Civil and Environmental Engineering, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milano, Italy gabriella.bolzon@polimi.it (Italy)

    2015-10-28

    The mechanical characterization of materials relies more and more often on sophisticated experimental methods that permit to acquire a large amount of data and, contemporarily, to reduce the invasiveness of the tests. This evolution accompanies the growing demand of non-destructive diagnostic tools that assess the safety level of components in use in structures and infrastructures, for instance in the strategic energy sector. Advanced material systems and properties that are not amenable to traditional techniques, for instance thin layered structures and their adhesion on the relevant substrates, can be also characterized by means of combined experimental-numerical tools elaborating data acquired by full-field measurement techniques. In this context, parameter identification procedures involve the repeated simulation of the laboratory or in situ tests by sophisticated and usually expensive non-linear analyses while, in some situation, reliable and accurate results would be required in real time. The effectiveness and the filtering capabilities of reduced models based on decomposition and interpolation techniques can be profitably used to meet these conflicting requirements. This communication intends to summarize some results recently achieved in this field by the author and her co-workers. The aim is to foster further interaction between engineering and mathematical communities.

  4. Control strategies for friction dampers: numerical assessment and experimental investigations.

    Directory of Open Access Journals (Sweden)

    Coelho H.T.

    2014-01-01

    Full Text Available The use of friction dampers has been proposed in a wide variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the dampers. The aim of this paper is to study three control strategies for friction dampers based on the hysteresis cycle. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these three strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for the numerical simulations. The obtained results show the good performance for the friction damper and the selected strategy.

  5. Advanced Sensors and Controls for Building Applications: Market Assessment and Potential R&D Pathways

    Energy Technology Data Exchange (ETDEWEB)

    Brambley, Michael R.; Haves, Philip; McDonald, Sean C.; Torcellini, Paul; Hansen, David G.; Holmberg, David; Roth, Kurt

    2005-04-13

    Significant energy savings can be achieved in commercial building operation, along with increased comfort and control for occupants, through the implementation of advanced technologies. This document provides a market assessment of existing building sensors and controls and presents a range of technology pathways (R&D options) for pursuing advanced sensors and building control strategies. This paper is actually a synthesis of five other white papers: the first describes the market assessment including estimates of market potential and energy savings for sensors and control strategies currently on the market as well as a discussion of market barriers to these technologies. The other four cover technology pathways: (1) current applications and strategies for new applications, (2) sensors and controls, (3) networking, security, and protocols and standards, and (4) automated diagnostics, performance monitoring, commissioning, optimal control and tools. Each technology pathway chapter gives an overview of the technology or application. This is followed by a discussion of needs and the current status of the technology. Finally, a series of research topics is proposed.

  6. Recent Advances in Biological Control of Pest Insects by Using Viruses in China

    Institute of Scientific and Technical Information of China (English)

    Xiu-lian SUN; Hui-yin PENG

    2007-01-01

    Insect viruses are attractive as biological control agents and could be a feasible alternative to chemical insecticides in the management of insect infestations. This review describes recent advances in the development of wild-type and genetically modified viruses as insecticides. A new strategy of application of insect viruses in China is reviewed. Also, the assessment of biosafety of genetically modified Helicoverpa armigera Nucleopolyhedovirus (HearNPV) is emphasized as a case-study.

  7. Control Strategy for Cascaded Medium - High Voltage STATCOM

    Directory of Open Access Journals (Sweden)

    Libing Chen

    2013-12-01

    Full Text Available Control strategy is researched for cascaded medium high static synchronous compensator to provide synthetic compensation ability of reactive power, harmonics and asymmetric currents. Basing on selective harmonic compensation strategy, a reference current detection method utilizing the combination of synchronous reference frame transformation and discrete Fourier transformation is proposed. The tracking control of instruction current is implemented by multi-carrier pulse width modulation (PWM. In allusion to the multi-carrier PWM, the capacitor voltage balancing control at the dc side is realized by a type of software based on the energy balance principle of the inverter bridge. The proposed control strategy is convenient for engineering implementation given its low calculation burden and simplicity. The effectiveness of the proposed control strategy is proven by both simulation and experimental results.

  8. A reduced energy supply strategy in active vibration control

    International Nuclear Information System (INIS)

    In this paper, a control strategy is presented and numerically tested. This strategy aims to achieve the potential performance of fully active systems with a reduced energy supply. These energy needs are expected to be comparable to the power demands of semi-active systems, while system performance is intended to be comparable to that of a fully active configuration. The underlying strategy is called 'global semi-active control'. This control approach results from an energy investigation based on management of the optimal control process. Energy management encompasses storage and convenient restitution. The proposed strategy monitors a given active law without any external energy supply by considering purely dissipative and energy-demanding phases. Such a control law is offered here along with an analysis of its properties. A suboptimal form, well adapted for practical implementation steps, is also given. Moreover, a number of numerical experiments are proposed in order to validate test findings

  9. Advanced modelling, monitoring, and process control of bioconversion systems

    Science.gov (United States)

    Schmitt, Elliott C.

    fermentation with diauxic growth. Model predictive control (MPC), an advanced process control strategy, is capable of utilizing nonlinear models and sensor feedback to provide optimal input while ensuring critical process constraints are met. Using the microorganism Saccharomyces cerevisiae, a commonly used microorganism for biofuel production, and work performed with M. thermoacetica, a nonlinear MPC was implemented on a continuous membrane cell-recycle bioreactor (MCRB) for the conversion of glucose to ethanol. The dilution rate was used to control the ethanol productivity of the system will maintaining total substrate conversion above the constraint of 98%. PLS multivariate models for glucose (RMSEP 1.5 g L-1) and ethanol (RMSEP 0.4 g L-1) were robust in predicting concentrations and a mechanistic kinetic model built accurately predicted continuous fermentation behavior. A setpoint trajectory, ranging from 2 - 4.5 g L-1 h-1 for productivity was closely tracked by the fermentation system using Raman measurements and an extended Kalman filter to estimate biomass concentrations. Overall, this work was able to demonstrate an effective approach for real-time monitoring and control of a complex fermentation system.

  10. Improved Droop Control Strategy for Grid-Connected Inverters

    DEFF Research Database (Denmark)

    Abusara, Mohammad; Sharkh, Suleiman; Guerrero, Josep M.

    2015-01-01

    An improved control strategy for grid-connected inverters within microgrids is presented in this paper. The strategy is based on the classical P-ω and Q-V droop method. The improvement in the proposed control strategy is twofold: Firstly, the transient response of the droop controller is improved...... by replacing the traditional method of measuring average power, which is based on using a first order low pass filter, by a real time integration filter. This is shown to reduce the imported transient energy when connecting to the grid. Secondly, the steady state output current quality is improved by utilising...

  11. Energy storage system control strategies for power distribution systems

    Directory of Open Access Journals (Sweden)

    Areewan Kajorndech

    2015-03-01

    Full Text Available Energy storage systems have been widely employed to attain several benefits, such as reliability improvement, stabilization of power systems connected with renewable energy resources, economic benefits and etc. To achieve the above objectives, the appropriate and effective control strategies for energy storage systems are needed to be developed. This research proposes energy storage system control strategies for power distribution systems equipped with a limited size of energy storage system in order to improve reliability and save energy costs by determining an optimal charging schedule of the energy storage system. Simulation results demonstrate the benefits of energy storage system applications under the different control strategies.

  12. Control system options and strategies for supercritical CO2 cycles.

    Energy Technology Data Exchange (ETDEWEB)

    Moisseytsev, A.; Kulesza, K. P.; Sienicki, J. J.; Nuclear Engineering Division; Oregon State Univ.

    2009-06-18

    The Supercritical Carbon Dioxide (S-CO{sub 2}) Brayton Cycle is a promising alternative to Rankine steam cycle and recuperated gas Brayton cycle energy converters for use with Sodium-Cooled Fast Reactors (SFRs), Lead-Cooled Fast Reactors (LFRs), as well as other advanced reactor concepts. The S-CO{sub 2} Brayton Cycle offers higher plant efficiencies than Rankine or recuperated gas Brayton cycles operating at the same liquid metal reactor core outlet temperatures as well as reduced costs or size of key components especially the turbomachinery. A new Plant Dynamics Computer Code has been developed at Argonne National Laboratory for simulation of a S-CO{sub 2} Brayton Cycle energy converter coupled to an autonomous load following liquid metal-cooled fast reactor. The Plant Dynamics code has been applied to investigate the effectiveness of a control strategy for the S-CO{sub 2} Brayton Cycle for the STAR-LM 181 MWe (400 MWt) Lead-Cooled Fast Reactor. The strategy, which involves a combination of control mechanisms, is found to be effective for controlling the S-CO{sub 2} Brayton Cycle over the complete operating range from 0 to 100 % load for a representative set of transient load changes. While the system dynamic analysis of control strategy performance for STARLM is carried out for a S-CO{sub 2} Brayton Cycle energy converter incorporating an axial flow turbine and compressors, investigations of the S-CO{sub 2} Brayton Cycle have identified benefits from the use of centrifugal compressors which offer a wider operating range, greater stability near the critical point, and potentially further cost reductions due to fewer stages than axial flow compressors. Models have been developed at Argonne for the conceptual design and performance analysis of centrifugal compressors for use in the SCO{sub 2} Brayton Cycle. Steady state calculations demonstrate the wider operating range of centrifugal compressors versus axial compressors installed in a S-CO{sub 2} Brayton Cycle as

  13. Multivariable quadratic synthesis of an advanced turbofan engine controller

    Science.gov (United States)

    Dehoff, R. L.; Hall, W. E., Jr.

    1978-01-01

    A digital controller for an advanced turbofan engine utilizing multivariate feedback is described. The theoretical background of locally linearized control synthesis is reviewed briefly. The application of linear quadratic regulator techniques to the practical control problem is presented. The design procedure has been applied to the F100 turbofan engine, and details of the structure of this system are explained. Selected results from simulations of the engine and controller are utilized to illustrate the operation of the system. It is shown that the general multivariable design procedure will produce practical and implementable controllers for modern, high-performance turbine engines.

  14. AC electric motors control advanced design techniques and applications

    CERN Document Server

    Giri, Fouad

    2013-01-01

    The complexity of AC motor control lies in the multivariable and nonlinear nature of AC machine dynamics. Recent advancements in control theory now make it possible to deal with long-standing problems in AC motors control. This text expertly draws on these developments to apply a wide range of model-based control designmethods to a variety of AC motors. Contributions from over thirty top researchers explain how modern control design methods can be used to achieve tight speed regulation, optimal energetic efficiency, and operation reliability and safety, by considering online state var

  15. Discrete Current Control Strategy of Permanent Magnet Synchronous Motors

    Directory of Open Access Journals (Sweden)

    Yan Dong

    2013-01-01

    Full Text Available A control strategy of permanent magnet synchronous motors (PMSMs, which is different from the traditional vector control (VC and direct torque control (DTC, is proposed. Firstly, the circular rotating magnetic field is analyzed on the simplified model and discredited into stepping magnetic field. The stepping magnetomotive force will drive the rotor to run as the stepping motor. Secondly, the stator current orientation is used to build the control model instead of rotor flux orientation. Then, the discrete current control strategy is set and adopted in positioning control. Three methods of the strategy are simulated in computer and tested on the experiment platform of PMSM. The control precision is also verified through the experiment.

  16. Advanced control room design for nuclear power plants

    International Nuclear Information System (INIS)

    The power industry has seen a continuous growth of size and complexity of nuclear power plants. Accompanying these changes have been extensive regulatory requirements resulting in significant construction, operation and maintenance costs. In response to related concerns raised by industry members, Combustion Engineering developed the NUPLEX 80 Advanced Control Room. The goal of NUPLEX 80TM is to: reduce design and construction costs; increase plant safety and availability through improvements in the man-machine interface; and reduce maintenance costs. This paper provides an overview of the NUPLEX 80 Advanced Control Room and explains how the stated goals are achieved. (author)

  17. A reactive control strategy for networked hydrographical system management

    OpenAIRE

    Duviella, Eric; Chiron, Pascale; Charbonnaud, Philippe

    2011-01-01

    A reactive control strategy is proposed to improve the water asset management of complex hydrographical systems. This strategy requires the definition of rules to achieve a generic resource allocation and setpoint assignment. A modelling method of the complex hydro- graphical network based on a weighted digraph of instrumented points, is also presented. The simulation results of the strategy applied to a hydrographical system composed of one confluent and two difluents show its efficiency and...

  18. The Modeling Strategies for Open Software Architecture of Robot Controller

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Although the modeling technologies for open robot controllers have been discussed widely, not much literature is devoted to the actual general modeling principles and strategies. The reason is that many researches focus on specific application fields. This paper accommodates for this lacuna and provides some general modeling principles and strategies. At last, the actual new modeling method -Hierarchical Object-Oriented Petri net (HOONet) which has been proved to be an effective modeling methodology, is used to illustrate the modeling strategies.

  19. Preschool Power Play: Resource Control Strategies Associated with Health

    Directory of Open Access Journals (Sweden)

    Amber R. Massey

    2014-01-01

    Full Text Available Background. This exploratory study uses a multimethod approach to examine the relationship between social strategy usage and overall health in preschool children. Methods. Children's temperament, social strategies, and health assessments were obtained via reported behavior from parents and teachers. In addition, children's use of prosocial and coercive strategies was observed and recorded via one-way windows in the preschool facility. Results. Results revealed that the temperament characteristic of effortful control was related to the observed use of coercive strategies and that coercive strategies were not observed by teachers, who viewed these children as primarily prosocial. The reported use of both coercive and prosocial strategies was also related to decrease in illness. Conclusion. These findings in relation to previous work suggest that using both prosocial and coercive strategies can elevate status as well as maintain health even in young children.

  20. Advanced Proportional Servo Valve Control with Customized Control Code using White Space

    OpenAIRE

    Lauer, Peter

    2016-01-01

    An industrial control valve has been designed by Eaton (AxisPro® valve). The servo performance valve has onboard electronics that features external and internal sensor interfaces, advanced control modes and network capability. Advanced control modes are implement in the valves firmware. With the help of the white space it is possilbe to execute custom code directly on the valve that interact with these controls. Small OEM applications, like rubber moulding machines, benefit from the cominatio...

  1. Control Strategies for Machining with Industrial Robots

    OpenAIRE

    Sörnmo, Olof

    2013-01-01

    This thesis presents methods for improving machining with industrial robots using control, with focus on increasing positioning accuracy and controlling feed rate. The strong process forces arising during high-speed machining operations, combined with the limited stiffness of industrial robots, have hampered the usage of industrial robots in high-end machining tasks. However, since such manipulators may offer flexible and cost-effective machining solutions compared to conventional machine ...

  2. Element Tracking Strategies for Hot Strip Laminar Cooling Control

    Institute of Scientific and Technical Information of China (English)

    HAN Bin; ZHANG Zhong-ping; LIU Xiang-hua; WANG Guo-dong

    2005-01-01

    Feedforward control is the core to control function in the cooling process of hot strip. One of the most important tasks in feedforward control is to determine the arrival time of the strip at various locations on the runout table for effective control. Based on the principles of element tracking and tracking strategies for variable rolling speed and constant rolling speed, a simple diagonal tracking method for an existing hot strip mill was proposed and tested. The test results show that the proposed strategies are effective for improving tracking control.

  3. Control strategies for VSC-based HVDC transmission system

    DEFF Research Database (Denmark)

    Stan, Ana-Irina; Stroe, Daniel Ioan; Silva, Rodrigo Da

    2011-01-01

    Throughout this paper the modeling and control of the VSC-based HVDC systems are investigated and described. Two different control methods capable of controlling such systems are proposed. Both developed control strategies are implemented in the dq synchronous reference frame. In order to analyze...... the behavior of the developed VSC-based HVDC transmission system two study cases are carried out using MATLAB/Simulink. The results obtained from simulations show acceptable performances, of the proposed strategies, when changes in the reference parameters are considered. The active power flow between...... the converters is succesfully achieved while, the independent control of active and reactive power is also verified....

  4. Advanced and intelligent control in power electronics and drives

    CERN Document Server

    Blaabjerg, Frede; Rodríguez, José

    2014-01-01

    Power electronics and variable frequency drives are continuously developing multidisciplinary fields in electrical engineering, and it is practically not possible to write a book covering the entire area by one individual specialist. Especially by taking account the recent fast development in the neighboring fields like control theory, computational intelligence and signal processing, which all strongly influence new solutions in control of power electronics and drives. Therefore, this book is written by individual key specialist working on the area of modern advanced control methods which penetrates current implementation of power converters and drives. Although some of the presented methods are still not adopted by industry, they create new solutions with high further research and application potential. The material of the book is presented in the following three parts: Part I: Advanced Power Electronic Control in Renewable Energy Sources (Chapters 1-4), Part II: Predictive Control of Power Converters and D...

  5. Contributions of CCLM to advances in quality control.

    Science.gov (United States)

    Kazmierczak, Steven C

    2013-01-01

    Abstract The discipline of laboratory medicine is relatively young when considered in the context of the history of medicine itself. The history of quality control, within the context of laboratory medicine, also enjoys a relatively brief, but rich history. Laboratory quality control continues to evolve along with advances in automation, measurement techniques and information technology. Clinical Chemistry and Laboratory Medicine (CCLM) has played a key role in helping disseminate information about the proper use and utility of quality control. Publication of important advances in quality control techniques and dissemination of guidelines concerned with laboratory quality control has undoubtedly helped readers of this journal keep up to date on the most recent developments in this field.

  6. Application of Advanced Process Control techniques to a pusher type reheating furnace

    Science.gov (United States)

    Zanoli, S. M.; Pepe, C.; Barboni, L.

    2015-11-01

    In this paper an Advanced Process Control system aimed at controlling and optimizing a pusher type reheating furnace located in an Italian steel plant is proposed. The designed controller replaced the previous control system, based on PID controllers manually conducted by process operators. A two-layer Model Predictive Control architecture has been adopted that, exploiting a chemical, physical and economic modelling of the process, overcomes the limitations of plant operators’ mental model and knowledge. In addition, an ad hoc decoupling strategy has been implemented, allowing the selection of the manipulated variables to be used for the control of each single process variable. Finally, in order to improve the system flexibility and resilience, the controller has been equipped with a supervision module. A profitable trade-off between conflicting specifications, e.g. safety, quality and production constraints, energy saving and pollution impact, has been guaranteed. Simulation tests and real plant results demonstrated the soundness and the reliability of the proposed system.

  7. Strategy Guideline: Advanced Construction Documentation Recommendations for High Performance Homes

    Energy Technology Data Exchange (ETDEWEB)

    Lukachko, A.; Gates, C.; Straube, J.

    2011-12-01

    As whole house energy efficiency increases, new houses become less like conventional houses that were built in the past. New materials and new systems require greater coordination and communication between industry stakeholders. The Guideline for Construction Documents for High Performance Housing provides advice to address this need. The reader will be presented with four changes that are recommended to achieve improvements in energy efficiency, durability and health in Building America houses: create coordination drawings, improve specifications, improve detail drawings, and review drawings and prepare a Quality Control Plan.

  8. 40 CFR 52.1129 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1129... strategy: Ozone. (a) Revisions to the State Implementation Plan submitted by the Massachusetts Department...) and 182(c)(2)(B) of the Clean Air Act for the Springfield, Massachusetts serious ozone...

  9. 40 CFR 52.2235 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.2235... strategy: Ozone. (a) Determination—EPA is determining that, as of August 8, 1995, the Nashville ozone nonattainment area has attained the ozone standard and that the reasonable further progress and...

  10. 40 CFR 52.1534 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... implementation rule (see 40 CFR 51.918), this determination suspends the reasonable further progress and... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1534... strategy: Ozone. (a) Revisions to the State Implementation Plan submitted by the New Hampshire...

  11. 40 CFR 52.2088 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... the provisions of EPA's ozone implementation rule (see 40 CFR 51.918), this determination suspends the... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.2088... strategy: Ozone. (a) Revisions to the State Implementation Plan submitted by the Rhode Island Department...

  12. 40 CFR 52.1880 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... NAAQS. These determinations, in accordance with 40 CFR 52.1004(c), suspend the requirements for these... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met because...

  13. 40 CFR 52.1476 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for the attainment and maintenance of the national standards for particulate matter...

  14. Control Strategy for Microgrid Inverter under Unbalanced Grid Voltage Conditions

    DEFF Research Database (Denmark)

    Guo, Xiaoqiang; Liu, Wenzhao; Zhang, X.;

    2014-01-01

    frame control strategy is proposed. It has a simple control structure due to no need of a phase-locked loop and voltage/current positive/negative sequence extraction calculation. The coordinate control of power and current quality is achieved, which enhances the operation performance of microgrid...

  15. Strategies for glucose control in people with type 1 diabetes

    DEFF Research Database (Denmark)

    Boiroux, Dimitri; Finan, Daniel Aaron; Jørgensen, John Bagterp;

    2011-01-01

    In this paper we apply a robust feedforward-feedback control strategy to people with type 1 diabetes. The feedforward controller consists of a bolus calculator which compensates the disturbance coming from meals. The feedback controller is based on a linearized description of the model describing...

  16. Strategies towards advanced ion track-based biosensors

    Science.gov (United States)

    Alfonta, L.; Bukelman, O.; Chandra, A.; Fahrner, W. R.; Fink, D.; Fuks, D.; Golovanov, V.; Hnatowicz, V.; Hoppe, K.; Kiv, A.; Klinkovich, I.; Landau, M.; Morante, J. R.; Tkachenko, N. V.; Vacík, J.; Valden, M.

    Three approaches towards ion track-based biosensors appear to be feasible. The development of the first one began a decade ago [Siwy, Z.; Trofin, L.; Kohl, P.; Baker, L.A.; Martin, C.R.; Trautmann, C. J. Am. Chem. Soc. 2005, 127, 5000-5001; Siwy, Z.S.; Harrell, C.C.; Heins, E.; Martin, C.R.; Schiedt, B.; Trautmann, C.; Trofin, L.; Polman, A. Presented at the 6th International Conference on Swift Heavy Ions in Matter, Aschaffenburg, Germany, May 28-31, 2005] and makes use of the concept that the presence of certain biomolecules within liquids can block the passage through narrow pores if being captured there, thus switching off the pore's electrical conductivity. The second, having been successfully tested half a year ago [Fink, D.; Klinkovich, I.; Bukelman, O.; Marks, R.S.; Fahrner, W.; Kiv, A.; Fuks, D.; Alfonta, L. Biosens. Bioelectron. 2009, 24, 2702-2706], is based on the accumulation of enzymatic reaction products within the confined volume of narrow etched ion tracks which modifies the pore's electrical conductivity. The third and most elegant, at present under development, will exploit the charge transfer from enzymes to semiconductors embedded within etched tracks, enabling the enzymes undergoing specific reactions with the biomolecules to be detected. These strategies can be realized either within carrier-free nanoporous polymeric membranes embedded in the corresponding bioliquids, or within contacted nanoporous insulating layers on semiconducting substrates, the so-called TEMPOS structures [Fink, D.; Petrov, A.; Hoppe, H.; Fahrner, W.R.; Papaleo, R.M.; Berdinsky, A.; Chandra, A.; Biswas, A.; Chadderton, L.T. Nucl. Instrum. Methods B 2004, 218, 355-361]. The latter have the advantage of exhibiting a number of peculiar electronic properties, such as the ability for logic and/or combination of input signals, tunable polarity, negative differential resistances, tunability by external parameters such as light, magnetic fields, etc. and self-pulsations, which

  17. Decentralized Coordinated Control Strategy of Islanded Microgrids

    DEFF Research Database (Denmark)

    Wu, Dan

    Facing the challenges brought by the traditional large power system concerning the environmental and economic issues, along recent years distributed generation is considered as an alternative solution to provide clean energy in a local manner. In this context, Microgrid which performing as a local...... small size grid, is emerging as a promising concept to flexibly control both sides of power generation and consumption as an integral controllable unit. Regarding whether there is main grid participating in the power regulation, the operation of Microgrid can be mainly classified as two modes: grid......-connected mode and islanded mode. In the islanded mode operation, since there is no energy back-up from the main grid, the coordinated control of power balance between generation and consumption encounters more challenges and this thesis is mainly focused on this scope. Hierarchical structure can be applied...

  18. Control Strategies for HCCI Mixed-Mode Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Robert M [ORNL; Edwards, Kevin Dean [ORNL

    2010-03-01

    Delphi Automotive Systems and ORNL established this CRADA to expand the operational range of Homogenous Charge Compression Ignition (HCCI) mixed-mode combustion for gasoline en-gines. ORNL has extensive experience in the analysis, interpretation, and control of dynamic engine phenomena, and Delphi has extensive knowledge and experience in powertrain compo-nents and subsystems. The partnership of these knowledge bases was important to address criti-cal barriers associated with the realistic implementation of HCCI and enabling clean, efficient operation for the next generation of transportation engines. The foundation of this CRADA was established through the analysis of spark-assisted HCCI data from a single-cylinder research engine. This data was used to (1) establish a conceptual kinetic model to better understand and predict the development of combustion instabilities, (2) develop a low-order model framework suitable for real-time controls, and (3) provide guidance in the initial definition of engine valve strategies for achieving HCCI operation. The next phase focused on the development of a new combustion metric for real-time characterization of the combustion process. Rapid feedback on the state of the combustion process is critical to high-speed decision making for predictive control. Simultaneous to the modeling/analysis studies, Delphi was focused on the development of engine hardware and the engine management system. This included custom Delphi hardware and control systems allowing for flexible control of the valvetrain sys-tem to enable HCCI operation. The final phase of this CRADA included the demonstration of conventional and spark assisted HCCI on the multi-cylinder engine as well as the characterization of combustion instabilities, which govern the operational boundaries of this mode of combustion. ORNL and Delphi maintained strong collaboration throughout this project. Meetings were held on a bi-weekly basis with additional reports, presentation, and

  19. A Novel Hybrid Safety-control Strategy for a Manipulator

    Directory of Open Access Journals (Sweden)

    Jing Xia

    2014-04-01

    Full Text Available As robots tend to work cooperatively with humans in shared workplaces, safety as regards robot- human interactions has caused a great deal of concern in the robot community, and control strategies have become a hot topic in robotics research. In order to guarantee the robot’s safety and continuous motions, this paper proposes a novel safety-control strategy, which is strictly conservative and which consists of a pre-contact and post-contact safety strategy. We adopt an optimal motion trajectory-planning method, by use of which the jerk, acceleration and velocity of the robot’s motion can be limited and a time-optimal motion can be obtained as a post-contact safety strategy for a position-controlled manipulator. The optimal motion trajectory planning not only reduces the impact forces during the collision period, but also maintains the efficiency of the manipulator and preserves continuous motions. Next, we describe a novel collision detection method as a pre-contact safety strategy to avoid collisions. The method proposed here can compute security warning region to handle the effect of robot motion on collision detection and detect collisions between non-convex polygon soups. Finally, the control strategy is implemented for a 7-DOF humanoid manipulator and the experimental results demonstrate the validity of this novel hybrid safety-control strategy.

  20. Sliding Mode Robustness Control Strategy for Shearer Height Adjusting System

    Directory of Open Access Journals (Sweden)

    Xiuping Su

    2013-09-01

    Full Text Available This paper firstly established mathematical model of height adjusting hydro cylinder of the shearer, as well as the state space equation of the shearer height adjusting system. Secondly we designed a shearer automatic height adjusting controller adopting the sliding mode robustness control strategy. The height adjusting controller includes the sliding mode surface switching function based on Ackermann formula, as well as sliding mode control function with the improved butterworth filter. Then simulation of the height adjustment controller shows that the sliding mode robustness control solves buffeting of typical controller, and achieves automatic control for the rolling drum of the shearer.

  1. Comparison of Advanced Distillation Control Methods, Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Dr. James B. Riggs

    2000-11-30

    Detailed dynamic simulations of three industrial distillation columns (a propylene/propane splitter, a xylene/toluene column, and a depropanizer) have been used to evaluate configuration selections for single-ended and dual-composition control, as well as to compare conventional and advanced control approaches. In addition, a simulator of a main fractionator was used to compare the control performance of conventional and advanced control. For each case considered, the controllers were tuned by using setpoint changes and tested using feed composition upsets. Proportional Integral (PI) control performance was used to evaluate the configuration selection problem. For single ended control, the energy balance configuration was found to yield the best performance. For dual composition control, nine configurations were considered. It was determined that the use of dynamic simulations is required in order to identify the optimum configuration from among the nine possible choices. The optimum configurations were used to evaluate the relative control performance of conventional PI controllers, MPC (Model Predictive Control), PMBC (Process Model-Based Control), and ANN (Artificial Neural Networks) control. It was determined that MPC works best when one product is much more important than the other, while PI was superior when both products were equally important. PMBC and ANN were not found to offer significant advantages over PI and MPC. MPC was found to outperform conventional PI control for the main fractionator. MPC was applied to three industrial columns: one at Phillips Petroleum and two at Union Carbide. In each case, MPC was found to significantly outperform PI controls. The major advantage of the MPC controller is its ability to effectively handle a complex set of constraints and control objectives.

  2. Vision Based Autonomous Robotic Control for Advanced Inspection and Repair

    Science.gov (United States)

    Wehner, Walter S.

    2014-01-01

    The advanced inspection system is an autonomous control and analysis system that improves the inspection and remediation operations for ground and surface systems. It uses optical imaging technology with intelligent computer vision algorithms to analyze physical features of the real-world environment to make decisions and learn from experience. The advanced inspection system plans to control a robotic manipulator arm, an unmanned ground vehicle and cameras remotely, automatically and autonomously. There are many computer vision, image processing and machine learning techniques available as open source for using vision as a sensory feedback in decision-making and autonomous robotic movement. My responsibilities for the advanced inspection system are to create a software architecture that integrates and provides a framework for all the different subsystem components; identify open-source algorithms and techniques; and integrate robot hardware.

  3. Paratransgenesis: a promising new strategy for mosquito vector control

    OpenAIRE

    Wilke, André Barretto Bruno; Marrelli, Mauro Toledo

    2015-01-01

    The three main mosquito genera, Anopheles, Aedes and Culex, transmit respectively malaria, dengue and lymphatic filariasis. Current mosquito control strategies have proved unsuccessful, and there still is a substantial number of morbidity and mortality from these diseases. Genetic control methods have now arisen as promising alternative strategies, based on two approaches: the replacement of a vector population by disease-refractory mosquitoes and the release of mosquitoes carrying a lethal g...

  4. Energy storage system control strategies for power distribution systems

    OpenAIRE

    Areewan Kajorndech; Dulpichet Rerkpreedapong

    2015-01-01

    Energy storage systems have been widely employed to attain several benefits, such as reliability improvement, stabilization of power systems connected with renewable energy resources, economic benefits and etc. To achieve the above objectives, the appropriate and effective control strategies for energy storage systems are needed to be developed. This research proposes energy storage system control strategies for power distribution systems equipped with a limited size of energy storage system ...

  5. Optical metrology for advanced process control: full module metrology solutions

    Science.gov (United States)

    Bozdog, Cornel; Turovets, Igor

    2016-03-01

    Optical metrology is the workhorse metrology in manufacturing and key enabler to patterning process control. Recent advances in device architecture are gradually shifting the need for process control from the lithography module to other patterning processes (etch, trim, clean, LER/LWR treatments, etc..). Complex multi-patterning integration solutions, where the final pattern is the result of multiple process steps require a step-by-step holistic process control and a uniformly accurate holistic metrology solution for pattern transfer for the entire module. For effective process control, more process "knobs" are needed, and a tighter integration of metrology with process architecture.

  6. Advanced reactor instrumentation and control reliability and risk assessment

    Energy Technology Data Exchange (ETDEWEB)

    Fullwood, R.; Gunther, W.; Valente, J.; Azarm, M.A.

    1991-12-31

    Advanced nuclear power reactors will used different approaches to achieving a higher level of safety than the first generation. One approach used the technological developments in computation and electronics in the form of digital instrumentation and control (I&C) to enhance the reliability, and accuracy of information for plant control, responding to the information, and controlling the plant and its systems under normal and upset environments in various states of degradation. Evaluating the reliability and safety of advanced I&C systems requires determining the reliability of the I&C used in the advanced reactors which involves distributed processing, data pile-up, interactive systems, the man-machine interface, various forms of automatic control, and systems interactions. From these analyses will come an understanding of the potential of the new I&C, and protection from its vulnerabilities to enhance the safe operation of the new plants. Technological, safety, reliability, and regulatory issues associated with advanced I&C for the new reactors are discussed herein. The issues are presented followed by suggested approaches to their resolution.

  7. Advanced reactor instrumentation and control reliability and risk assessment

    Energy Technology Data Exchange (ETDEWEB)

    Fullwood, R.; Gunther, W.; Valente, J.; Azarm, M.A.

    1991-01-01

    Advanced nuclear power reactors will used different approaches to achieving a higher level of safety than the first generation. One approach used the technological developments in computation and electronics in the form of digital instrumentation and control (I C) to enhance the reliability, and accuracy of information for plant control, responding to the information, and controlling the plant and its systems under normal and upset environments in various states of degradation. Evaluating the reliability and safety of advanced I C systems requires determining the reliability of the I C used in the advanced reactors which involves distributed processing, data pile-up, interactive systems, the man-machine interface, various forms of automatic control, and systems interactions. From these analyses will come an understanding of the potential of the new I C, and protection from its vulnerabilities to enhance the safe operation of the new plants. Technological, safety, reliability, and regulatory issues associated with advanced I C for the new reactors are discussed herein. The issues are presented followed by suggested approaches to their resolution.

  8. Unique strategies to control reproduction in camels.

    Science.gov (United States)

    Skidmore, J A; Morton, K M; Billah, M

    2010-01-01

    The reproductive efficiency of camels is low under natural pastural conditions and so the use of artifical insemination and embryo transfer are becoming increasingly important to improve their breeding potential. Methods to control their reproductive cycle are therefore essential. This review describes characteristics of the ovarian follicular wave pattern in camels and exogenous hormonal control of ovulation. It also summarizes the difficulties involved with artifical insemination and analyzing the highly gelatinous semen, and reports on the latest methods used to try and reduce the viscosity and liquefy camel semen. In addition an account is given of different hormonal and physical methods used to synchronise follicular waves, and various hormone treatments used to broaden the availability of ovulated, asynchronous and non-ovulated recipients are discussed. PMID:21755692

  9. Access control and interlock system at the Advanced Photon Source

    Energy Technology Data Exchange (ETDEWEB)

    Forrestal, J.; Hogrefe, R.; Knott, M.; McDowell, W.; Reigle, D.; Solita, L.; Koldenhoven, R.; Haid, D. [Argonne National Lab., IL (United States). Advanced Photon Source

    1997-08-01

    The Advanced Photon Source (APS) consists of a linac, position accumulator ring (PAR), booster synchrotron, storage ring, and up to 70 experimental beamlines. The Access Control and Interlock System (ACIS) utilizes redundant programmable logic controllers (PLCs) and a third hard-wired chain to protect personnel from prompt radiation generated by the linac, PAR, synchrotron, and storage ring. This paper describes the ACIS`s design philosophy, configuration, hardware, functionality, validation requirements, and operational experience.

  10. UAV Robust Strategy Control Based on MAS

    OpenAIRE

    Jian Han; Changhong Wang; Guoxing Yi

    2014-01-01

    A novel multiagent system (MAS) has been proposed to integrate individual UAV (unmanned aerial vehicle) to form a UAV team which can accomplish complex missions with better efficiency and effect. The MAS based UAV team control is more able to conquer dynamic situations and enhance the performance of any single UAV. In this paper, the MAS proposed and established combines the reacting and thinking abilities to be an initiative and autonomous hybrid system which can solve missions involving coo...

  11. Integrating Strategy-Making through Interactive Controls

    OpenAIRE

    Sax, Johanna; Juul Andersen, Torben

    2013-01-01

    Strategic responses to complex and frequent environmental changes must balance the tension between innovative opportunistic search and optimization of operating processes. The ability to survive and thrive depends on an ability to facilitate dispersed exploratory initiatives, test their commercial viability, and exploit the associated business opportunities. However, dispersion of authority requires coordination as well as empowerment calls for extended controls. Hence, there is a tension bet...

  12. Evaluation of control strategies in forming processes

    Directory of Open Access Journals (Sweden)

    Calmano Stefan

    2015-01-01

    Full Text Available Products of forming processes are subject to quality fluctuations due to uncertainty in semi-finished part properties as well as process conditions and environment. An approach to cope with these uncertainties is the implementation of a closed-loop control taking into account the actual product properties measured by sensors or estimated by a mathematical process model. Both methods of uncertainty control trade off with a financial effort. In case of sensor integration the effort is the cost of the sensor including signal processing as well as the design and manufacturing effort for integration. In case of an estimation model the effort is mainly determined by the time and knowledge needed to derive the model, identify the parameters and implement the model into the PLC. The risk of mismatch between model and reality as well as the risk of wrong parameter identification can be assumed as additional uncertainty (model uncertainty. This paper evaluates controlled and additional uncertainty by taking into account process boundary conditions like the degree of fluctuations in semi-finished part properties. The proposed evaluation is demonstrated by the analysis of exemplary processes.

  13. A Comparative Study between Two Control Strategies for Matrix Converter

    Directory of Open Access Journals (Sweden)

    BENDIABDELLAH, A.

    2009-06-01

    Full Text Available The authors compare two control strategies for direct AC-AC matrix converters; namely the Venturini method and the scalar strategy control method. The performance comparison of the two strategies is made under unbalanced distorted torque, rotor speed and stator current operation. The simulation of the three-phase matrix converter feeding an induction motor was accomplished by means of the Matlab/Simulink software. This package makes it possible to simulate the dynamic systems in a simple way and in graphic environment.

  14. A Novel Hybrid Safety-control Strategy for a Manipulator

    OpenAIRE

    Jing Xia; Zainan Jiang; Hong Liu; Hegao Cai; Guangxin Wu

    2014-01-01

    As robots tend to work cooperatively with humans in shared workplaces, safety as regards robot- human interactions has caused a great deal of concern in the robot community, and control strategies have become a hot topic in robotics research. In order to guarantee the robot’s safety and continuous motions, this paper proposes a novel safety-control strategy, which is strictly conservative and which consists of a pre-contact and post-contact safety strategy. We adopt an optimal motion trajecto...

  15. Application of a controllable degron strategy for metabolic engineering

    DEFF Research Database (Denmark)

    Knuf, Christoph; Maury, Jerome; Jacobsen, Simo Abdessamad;

    2014-01-01

    into the heterologous pathway. Unfortunately some deletions are lethal, as end products of pathways are needed for cellular growth. One example of such a pathway is the mevalonate pathway in S. cerevisiae with ergosterol as one of the most important end products. A great number of bioactive compounds, like various...... terpenoids, can be produced from intermediates of this pathway. Different strategies have been applied in order to down-regulate the expression of enzymes involved in the mevalonate pathway. All these strategies work on the transcriptional level. This leads to a delay of the actual regulation......, as the existing enzyme will still be active. We present a strategy for down-regulation that acts on the protein level and which can therefore be controlled in a more precise manner than the hitherto reported strategies. As a case study we show the action of the degron strategy for controlling the pools...

  16. Delta Power Control Strategy for Multi-String Grid-Connected PV Inverters

    DEFF Research Database (Denmark)

    Sangwongwanich, Ariya; Yang, Yongheng; Blaabjerg, Frede;

    2016-01-01

    With a still increasing penetration level of grid-connected PV systems, more advanced active power control functionalities have been introduced in certain grid regulations. A delta power constraint, where a portion of the active power from the PV panels is reserved during operation, is required...... for grid support (e.g., during frequency deviation). In this paper, a cost-effective solution to realize delta power control for grid-connected PV systems is presented, where the residential/commercial multi-string PV inverter configuration is adopted. This control strategy is a combination of Maximum...... Power Point Tracking (MPPT) and Constant Power Generation (CPG) modes. In this control scheme, one PV string operating in the MPPT mode estimates the available power, while the other PV strings regulate the total PV power by the CPG control strategy in such a way that the delta power constraint...

  17. Dynamic Event Tree advancements and control logic improvements

    Energy Technology Data Exchange (ETDEWEB)

    Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mandelli, Diego [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sen, Ramazan Sonat [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cogliati, Joshua Joseph [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-01

    The RAVEN code has been under development at the Idaho National Laboratory since 2012. Its main goal is to create a multi-purpose platform for the deploying of all the capabilities needed for Probabilistic Risk Assessment, uncertainty quantification, data mining analysis and optimization studies. RAVEN is currently equipped with three different sampling categories: Forward samplers (Monte Carlo, Latin Hyper Cube, Stratified, Grid Sampler, Factorials, etc.), Adaptive Samplers (Limit Surface search, Adaptive Polynomial Chaos, etc.) and Dynamic Event Tree (DET) samplers (Deterministic and Adaptive Dynamic Event Trees). The main subject of this document is to report the activities that have been done in order to: start the migration of the RAVEN/RELAP-7 control logic system into MOOSE, and develop advanced dynamic sampling capabilities based on the Dynamic Event Tree approach. In order to provide to all MOOSE-based applications a control logic capability, in this Fiscal Year an initial migration activity has been initiated, moving the control logic system, designed for RELAP-7 by the RAVEN team, into the MOOSE framework. In this document, a brief explanation of what has been done is going to be reported. The second and most important subject of this report is about the development of a Dynamic Event Tree (DET) sampler named “Hybrid Dynamic Event Tree” (HDET) and its Adaptive variant “Adaptive Hybrid Dynamic Event Tree” (AHDET). As other authors have already reported, among the different types of uncertainties, it is possible to discern two principle types: aleatory and epistemic uncertainties. The classical Dynamic Event Tree is in charge of treating the first class (aleatory) uncertainties; the dependence of the probabilistic risk assessment and analysis on the epistemic uncertainties are treated by an initial Monte Carlo sampling (MCDET). From each Monte Carlo sample, a DET analysis is run (in total, N trees). The Monte Carlo employs a pre-sampling of the

  18. Dynamic Event Tree advancements and control logic improvements

    International Nuclear Information System (INIS)

    The RAVEN code has been under development at the Idaho National Laboratory since 2012. Its main goal is to create a multi-purpose platform for the deploying of all the capabilities needed for Probabilistic Risk Assessment, uncertainty quantification, data mining analysis and optimization studies. RAVEN is currently equipped with three different sampling categories: Forward samplers (Monte Carlo, Latin Hyper Cube, Stratified, Grid Sampler, Factorials, etc.), Adaptive Samplers (Limit Surface search, Adaptive Polynomial Chaos, etc.) and Dynamic Event Tree (DET) samplers (Deterministic and Adaptive Dynamic Event Trees). The main subject of this document is to report the activities that have been done in order to: start the migration of the RAVEN/RELAP-7 control logic system into MOOSE, and develop advanced dynamic sampling capabilities based on the Dynamic Event Tree approach. In order to provide to all MOOSE-based applications a control logic capability, in this Fiscal Year an initial migration activity has been initiated, moving the control logic system, designed for RELAP-7 by the RAVEN team, into the MOOSE framework. In this document, a brief explanation of what has been done is going to be reported. The second and most important subject of this report is about the development of a Dynamic Event Tree (DET) sampler named 'Hybrid Dynamic Event Tree' (HDET) and its Adaptive variant 'Adaptive Hybrid Dynamic Event Tree' (AHDET). As other authors have already reported, among the different types of uncertainties, it is possible to discern two principle types: aleatory and epistemic uncertainties. The classical Dynamic Event Tree is in charge of treating the first class (aleatory) uncertainties; the dependence of the probabilistic risk assessment and analysis on the epistemic uncertainties are treated by an initial Monte Carlo sampling (MCDET). From each Monte Carlo sample, a DET analysis is run (in total, N trees). The Monte Carlo employs a pre

  19. The environmental control and life support system advanced automation project. Phase 1: Application evaluation

    Science.gov (United States)

    Dewberry, Brandon S.

    1990-01-01

    The Environmental Control and Life Support System (ECLSS) is a Freedom Station distributed system with inherent applicability to advanced automation primarily due to the comparatively large reaction times of its subsystem processes. This allows longer contemplation times in which to form a more intelligent control strategy and to detect or prevent faults. The objective of the ECLSS Advanced Automation Project is to reduce the flight and ground manpower needed to support the initial and evolutionary ECLS system. The approach is to search out and make apparent those processes in the baseline system which are in need of more automatic control and fault detection strategies, to influence the ECLSS design by suggesting software hooks and hardware scars which will allow easy adaptation to advanced algorithms, and to develop complex software prototypes which fit into the ECLSS software architecture and will be shown in an ECLSS hardware testbed to increase the autonomy of the system. Covered here are the preliminary investigation and evaluation process, aimed at searching the ECLSS for candidate functions for automation and providing a software hooks and hardware scars analysis. This analysis shows changes needed in the baselined system for easy accommodation of knowledge-based or other complex implementations which, when integrated in flight or ground sustaining engineering architectures, will produce a more autonomous and fault tolerant Environmental Control and Life Support System.

  20. Controlling death: the false promise of advance directives.

    Science.gov (United States)

    Perkins, Henry S

    2007-07-01

    Advance directives promise patients a say in their future care but actually have had little effect. Many experts blame problems with completion and implementation, but the advance directive concept itself may be fundamentally flawed. Advance directives simply presuppose more control over future care than is realistic. Medical crises cannot be predicted in detail, making most prior instructions difficult to adapt, irrelevant, or even misleading. Furthermore, many proxies either do not know patients' wishes or do not pursue those wishes effectively. Thus, unexpected problems arise often to defeat advance directives, as the case in this paper illustrates. Because advance directives offer only limited benefit, advance care planning should emphasize not the completion of directives but the emotional preparation of patients and families for future crises. The existentialist Albert Camus might suggest that physicians should warn patients and families that momentous, unforeseeable decisions lie ahead. Then, when the crisis hits, physicians should provide guidance; should help make decisions despite the inevitable uncertainties; should share responsibility for those decisions; and, above all, should courageously see patients and families through the fearsome experience of dying.

  1. Creating a Web of Support: An Important Leadership Strategy for Advancing Campus Diversity

    Science.gov (United States)

    Kezar, Adrianna; Eckel, Peter; Contreras-McGavin, Melissa; Quaye, Stephen John

    2008-01-01

    Research demonstrates that leadership, particularly among presidents, is important for moving a diversity agenda forward and make appreciable progress on it. The research questions pursued here are: What is the role of the college president in advancing a diversity agenda? What strategies do presidents identify as important to facilitating a…

  2. SARS: hospital infection control and admission strategies.

    Science.gov (United States)

    Ho, Pak-Leung; Tang, Xiao-Ping; Seto, Wing-Hong

    2003-11-01

    Nosocomial clustering with transmission to health care workers, patients and visitors is a prominent feature of severe acute respiratory syndrome (SARS). Hospital outbreaks of SARS typically occurred within the first week after admission of the very first SARS cases when the disease was not recognized and before isolation measures were implemented. In the majority of nosocomial infections, there was a history of close contact with a SARS patient, and transmission occurred via large droplets, direct contact with infectious material or by contact with fomites contaminated by infectious material. In a few instances, potential airborne transmission was reported in association with endotracheal intubation, nebulised medications and non-invasive positive pressure ventilation of SARS patients. In all SARS-affected countries, nosocomial transmission of the disease was effectively halted by enforcement of routine standard, contact and droplet precautions in all clinical areas and additional airborne precautions in the high-risk areas. In Hong Kong, where there are few private rooms for patient isolation, some hospitals have obtained good outcome by having designated SARS teams and separate wards for patient triage, confirmed SARS cases and step-down of patients in whom SARS had been ruled out. In conclusion, SARS represents one of the new challenges for those who are involved in hospital infection control. As SARS might re-emerge, all hospitals should take advantage of the current SARS-free interval to review their infection control programmes, alert mechanisms, response capability and to repair any identified inadequacies.

  3. Field evaluation of advanced controls for the retrofit of packaged air conditioners and heat pumps

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

    2015-09-01

    This paper documents the magnitude of energy savings achievable in the field by retrofitting existing packaged rooftop units (RTUs) with advanced control strategies not ordinarily used for RTUs. A total of 66 RTUs on 8 different buildings were retrofitted with a commercially available advanced controller for improving RTU operational efficiency. The controller features enhanced air-side economizer control, multi-speed fan control, and demand controlled ventilation. Of the 66 RTUs, 18 are packaged heat pumps and the rest are packaged air conditioners with gas heat. The eight buildings cover four building types and four climate conditions. Based on the data collected for about a whole year, the advanced controller reduced the normalized annual RTU energy consumption between 22% and 90%, with an average of 57% for all RTUs. The average fractional savings uncertainty was 12% at 95% confidence level. Normalized annual electricity savings were in the range between 0.47 kWh/h (kWh per hour of RTU operation) and 7.21 kWh/h, with an average of 2.39 kWh/h. RTUs greater than 53 kW and runtime greater than 14 hours per day had payback periods less than 3 years even at $0.05/kWh.

  4. Spectrophotometric Procedure for Fast Reactor Advanced Coolant Manufacture Control

    Science.gov (United States)

    Andrienko, O. S.; Egorov, N. B.; Zherin, I. I.; Indyk, D. V.

    2016-01-01

    The paper describes a spectrophotometric procedure for fast reactor advanced coolant manufacture control. The molar absorption coefficient of dimethyllead dibromide with dithizone was defined as equal to 68864 ± 795 l·mole-1·cm-1, limit of detection as equal to 0.583 · 10-6 g/ml. The spectrophotometric procedure application range was found to be equal to 37.88 - 196.3 g. of dimethyllead dibromide in the sample. The procedure was used within the framework of the development of the method of synthesis of the advanced coolant for fast reactors.

  5. Strategy of control for bacterial biofilm processes

    Directory of Open Access Journals (Sweden)

    A. N. Mayansky

    2012-01-01

    Full Text Available Main directions of the modern search of the antibiofilm preparations aimed at adhesive bacterial reactions, control of QS-systems, influence over bis-(3’-5’-cyclic dimeric guanosine monophosphate (cdi-GMP, and secretory bacterial processes are analysed. Approaches for biofilm dispersal and increasing the sensitivity of biofilm bacteria to antimicrobial drugs are discussed. It is underlined that the majority of inhibitor molecules were studied in vitro or in infected mice experiments. It is prognosed that in future there will appear medical preparations which will help for fighting bacterial biofilms preventing their development and spreading in the host organism.

  6. PERFUSION SYSTEM CONTROLLER STRATEGIES DURING AN ECMO SUPPORT

    Directory of Open Access Journals (Sweden)

    M.Dhinakaran

    2014-12-01

    Full Text Available In this work modelling and control of Perfusion system is presented. The Perfusion system simultaneously controls the partial pressures during Extra Corporeal Membrane Oxygenation (ECMO support. The main Problem in ECMO system is exchange of Blood Gases in the Artificial Lung (Oxygenator.It is a highly Nonlinear Process comprising time-varying parameters, and varying time delays, it is currently being controlled manually by trained Perfusionist. The new control strategy implemented here has a feedback linearization routine with time-delay compensation for the Partial pressuresof Oxygen and Carbon dioxide. The controllers were tuned robustly and tested in simulations with a detailed artificial Lung (Oxygenator model in Cardiopulmonary bypass conditions. This Automatic control strategy is proposed to improve the patient’s safety by fast control reference tracking and good disturbance rejection under varying conditions.

  7. How Life Experience Shapes Cognitive Control Strategies: The Case of Air Traffic Control Training

    OpenAIRE

    Arbula, Sandra; Capizzi, Mariagrazia; Lombardo, Nicoletta; Vallesi, Antonino

    2016-01-01

    Although human flexible behavior relies on cognitive control, it would be implausible to assume that there is only one, general mode of cognitive control strategy adopted by all individuals. For instance, different reliance on proactive versus reactive control strategies could explain inter-individual variability. In particular, specific life experiences, like a highly demanding training for future Air Traffic Controllers (ATCs), could modulate cognitive control functions. A group of ATC trai...

  8. Strategies for controlling pollution from vehicular emissions in Beijing

    International Nuclear Information System (INIS)

    The paper describes the severe situation of vehicular emission in Beijing and discusses the following mitigation strategies: Improving fuel quality, controlling the exhaust from new vehicles, controlling the emissions from vehicles in use through e.g. Inspection Maintenance (I/M), renovating in-use vehicles and scrapping of old vehicles and road infrastructure and traffic policies. (Author)

  9. An advanced control system for a next generation transport aircraft

    Science.gov (United States)

    Rising, J. J.; Davis, W. J; Grantham, W. D.

    1983-01-01

    The use of modern control theory to develop a high-authority stability and control system for the next generation transport aircraft is described with examples taken from work performed on an advanced pitch active control system (PACS). The PACS was configured to have short-period and phugoid modes frequency and damping characteristics within the shaded S-plane areas, column force gradients with set bounds and with constant slope, and a blended normal-acceleration/pitch rate time history response to a step command. Details of the control law, feedback loop, and modal control syntheses are explored, as are compensation for the feedback gain, the deletion of the velocity signal, and the feed-forward compensation. Scheduling of the primary and secondary gains are discussed, together with control law mechanization, flying qualities analyses, and application on the L-1011 aircraft.

  10. Decoupling Control Strategy for Single Phase SPWM Parallel Inverters

    Institute of Scientific and Technical Information of China (English)

    Shun-Gang Xu; Jian-Ping Xu; Tai-Qiang Cao

    2009-01-01

    A decoupling control strategy of inverter parallel system is proposed based on the equivalent output impedance of single phase voltage source SPWM (sinusoidal pulse width modulation) inverter. The active power and reactive power are calculated in terms of output voltage and current of the inverter, and sent to the other inverters in the parallel system via controller area network (CAN) bus. By calculating and decoupling the circumfluence of the active power and reactive power, the inverters can share load current via the regulation of the reference-signal phase and amplitude. Experimental results of an 110V/2kVA inverter parallel system show the feasibility of the decoupling control strategy.

  11. Material Protection, Accounting, and Control Technologies (MPACT) Advanced Integration Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    Durkee, Joe W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cipiti, Ben [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Demuth, Scott Francis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fallgren, Andrew James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jarman, Ken [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Li, Shelly [Argonne National Lab. (ANL), Argonne, IL (United States); Meier, Dave [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Miller, Mike [Argonne National Lab. (ANL), Argonne, IL (United States); Osburn, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pereira, Candido [Argonne National Lab. (ANL), Argonne, IL (United States); Dasari, Venkateswara Rao [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ticknor, Lawrence O. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Yoo, Tae-Sic [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-09-30

    The development of sustainable advanced nuclear fuel cycles is a long-term goal of the Office of Nuclear Energy’s (DOE-NE) Fuel Cycle Technologies program. The Material Protection, Accounting, and Control Technologies (MPACT) campaign is supporting research and development (R&D) of advanced instrumentation, analysis tools, and integration methodologies to meet this goal (Miller, 2015). This advanced R&D is intended to facilitate safeguards and security by design of fuel cycle facilities. The lab-scale demonstration of a virtual facility, distributed test bed, that connects the individual tools being developed at National Laboratories and university research establishments, is a key program milestone for 2020. These tools will consist of instrumentation and devices as well as computer software for modeling, simulation and integration.

  12. Optimized Control Strategy For Over Loaded Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Knudsen, Torben; Wisniewski, Rafal;

    2015-01-01

    Abstract Optimized control strategy for overloaded offshore wind turbines Introduction Operation and maintenance cost are an important part of cost of energy especially for offshore wind farms. Typically unplanned service is called for due to detection off excessive loads on components, e...... controller tuning for a given wind turbine. It also enables a very safe and robust comparison between a new control strategy and the present one. Main body of abstract Is it true that power de-rating indeed the best way to reduce loads? The power de-rating approach has the drawback of only indirectly...... as results of ensuring the load reduction to the given level. A MPC controller is configured and tuned using this novel approach including Pareto fronts. It is compared to the existing de-rating strategy using high fidelity aero-servo-elastic simulation code and the possibilities for reduction of cost...

  13. Adaptive Landing Gear: Optimum Control Strategy and Potential for Improvement

    Directory of Open Access Journals (Sweden)

    Grzegorz Mikułowski

    2009-01-01

    Full Text Available An adaptive landing gear is a landing gear (LG capable of active adaptation to particular landing conditions by means of controlled hydraulic force. The objective of the adaptive control is to mitigate the peak force transferred to the aircraft structure during touch-down, and thus to limit the structural fatigue factor. This paper investigates the ultimate limits for improvement due to various strategies of active control. Five strategies are proposed and investigated numerically using a~validated model of a real, passive landing gear as a reference. Potential for improvement is estimated statistically in terms of the mean and median (significant peak strut forces as well as in terms of the extended safe sinking velocity range. Three control strategies are verified experimentally using a laboratory test stand.

  14. Regulatory controls for NORM contamination: Emerging issues and strategies

    International Nuclear Information System (INIS)

    Naturally occurring and accelerator-produced radioactive material (NORM) faces the increasing likelihood of federal or state regulatory control. Public concern and limited preliminary survey data fuel the debate over the necessity, approach, and jurisdiction of a NORM regulatory strategy. This debate requires the resolution of technical controversies and potentially competing state and federal agency interests. An additional facet of the debate is the impact of regulation upon traditionally non-nuclear industries, such as oil and gas production. Regulatory response has been initiated in several states, such as Louisiana's controls on equipment used in oil and gas production, to control specific industrial activities which generate NORM. A more comprehensive, generic federal strategy to control NORM contamination is also under review by the Environmental Protection Agency. This paper will detail the emerging technical issues, federal and state regulatory strategies under consideration, and evaluate the efficacy of selected regulatory approaches. (author)

  15. Structure and Control Strategies of Fuel Cell Vehicle

    Institute of Scientific and Technical Information of China (English)

    宋建国; 张承宁; 孙逢春; 钟秋海

    2004-01-01

    The structure and kinds of the fuel cell vehicle (FCV) and the mathematical model of the fuel cell processor are discussed in detail. FCV includes many parts: the fuel cell thermal and water management, fuel supply, air supply and distribution, AC motor drive, main and auxiliary power management, and overall vehicle control system. So it requires different kinds of control strategies, such as the PID method, zero-pole method, optimal control method, fuzzy control and neural network control. Along with the progress of control method, the fuel cell vehicle's stability and reliability is up-and-up. Experiment results show FCV has high energy efficiency.

  16. This weapon called peace: The doctrine and strategy of Soviet arms control and disarmament policy

    Energy Technology Data Exchange (ETDEWEB)

    Trifan, D.D.

    1989-01-01

    The strategy of Soviet arms-control and disarmament policy can be summarized in what we have termed the ratchet strategy of peaceful coexistence, in which a strategic advance is achieved through the tactics of multiple and indirect lines of approach, legitimized through invocation of peaceful coexistence, and made permanent and irreversible both by treaties and agreements and by the increasing military capability of the Soviet Union and her allies. This strategy is unchanged from World War II until today. Soviet strategic thought is based on the writings of V. I. Lenin; and both Lenin's strategic concepts and Soviet disarmament and arms-control strategy bear a striking resemblance to the precepts expressed by the 4th-century B.C. Chinese strategist Sun Tzu in the Art of War. This dissertation examines not only the strategic content of this policy, but the doctrinal components of Soviet disarmament and arms control strategy. The doctrinal principles must be derived through examination of: authoritative political and strategic writings, records of negotiations and negotiating positions, treaties and agreements, data concerning weapons systems, and the relationship of these to observed political and strategic developments during the period under examination. The doctrinal principles behind this strategy are: (1) the primary purpose of peaceful coexistence is the undermining of imperialism, (2) any means are permissible in the pursuit of peace strategy, and (3) the motive force for this strategy is Marxist-Leninist ideology, with the ultimate goal being the worldwide imposition of socialism in its Soviet variety. Shifts in Soviet policy are tactical instead of strategic in nature; and in keeping with the Soviet idea of the correlation of forces this strategy can be termed a time-fluid two-player zero-sum game. Consequently, Soviet arms-control and disarmament policy can be a weapon called peace.

  17. Nonlinear Economic Model Predictive Control Strategy for Active Smart Buildings

    DEFF Research Database (Denmark)

    Santos, Rui Mirra; Zong, Yi; Sousa, Joao M. C.;

    2016-01-01

    Nowadays, the development of advanced and innovative intelligent control techniques for energy management in buildings is a key issue within the smart grid topic. A nonlinear economic model predictive control (EMPC) scheme, based on the branch-and-bound tree search used as optimization algorithm...... for solving the nonconvex optimization problem is proposed in this paper. A simulation using the nonlinear model-based controller to control the temperature levels of an intelligent office building (PowerFlexHouse) is addressed. Its performance is compared with a linear model-based controller. The nonlinear...

  18. Modelling and Control Design of Unified Power Flow Controller for Various Control Strategies

    Directory of Open Access Journals (Sweden)

    T. Nireekshana

    2010-11-01

    Full Text Available Unified Power Flow Controller (UPFC is used to control the power flow in the transmission systems by controlling the impedance, voltage magnitude and phase angle. This controller offers advantages in terms of static and dynamic operation of the power system. It also brings in new challenges in power electronics and power system design. The basic structure of the UPFC consists of two voltage source inverter (VSI; where one converter is connected in parallel to the transmission line while the other is in series with the transmission line. The aim of the paper is to develop a control strategy for UPFC, modeling UPFC using MATLAB/SIMULINK and to analyze the control strategy to use the series voltage injection and shunt current injection for UPFC control. To simplify the design procedure we carry out the design for the series and shunt branches separately.In each case, a simple equivalent circuit represents the external system. The design has to be validated when the various subsystems are integrated.

  19. Reading comprehension metacognitive strategies as a means for controlling behavior

    Directory of Open Access Journals (Sweden)

    Dinorah Aladina Caballero López

    2014-07-01

    Full Text Available Textual comprehension implies the use of various metacognitive strategies by the students when they have to face a text to be competent readers. That is why the objective of this article is to illustrate the application of metacognitive strategies in order to achieve an efficient textual comprehension, taking into account the self – regulation the student exerts over his own learning process. It is applied as the main method historical-logical studies based on a professional-researching systematic practice; at the same time observation is largely used. The main result is the introduction of metacognitive strategies in reading comprehension, which subsequently favor the self-control of personal behavior. The article is the result of a research project sponsored by the department of Special Education. Key words: reading comprehension, metacognitive strategies, behavior self-control.

  20. A NEW STOCHASTIC OPTIMAL CONTROL STRATEGY FOR HYSTERETIC MR DAMPERS

    Institute of Scientific and Technical Information of China (English)

    YingZuguang; NiYiqing; KoJanming

    2004-01-01

    A new stochastic optimal control strategy for randomly excited quasi-integrable Hamiltonian systems using magneto-theological (MR) dampers is proposed. The dynamic behavior of an MR damper is characterized by the Bouc-Wen hysteretic model. The control force produced by the MR damper is separated into a passive part incorporated in the uncontrolled system and a semi-active part to be determined. The system combining the Bouc-Wen hysteretic force is converted into an equivalent non-hysteretic nonlinear stochastic control system. Then Ito stochastic differential equations are derived from the equivalent system by using the stochastic averaging method. A dynamical programming equation for the controlled diffusion processes is established based on the stochastic dynamical programming principle. The non-clipping nonlinear optimal control law is obtained for a certain performance index by minimizing the dynamical programming equation. Finally, an example is given to illustrate the application and effectiveness of the proposed control strategy.

  1. Advanced Control Design for Wind Turbines; Part I: Control Design, Implementation, and Initial Tests

    Energy Technology Data Exchange (ETDEWEB)

    Wright, A. D.; Fingersh, L. J.

    2008-03-01

    The purpose of this report is to give wind turbine engineers information and examples of the design, testing through simulation, field implementation, and field testing of advanced wind turbine controls.

  2. Invasive mechanism and control strategy of Ageratina adenophora (Sprengel)

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In order to ascertain the invasive mechanism and control strategy of the invasive Crofton weed, Ageratina adenophora, its ecological adaptability and population differentiation,the formation of single dominant population, displacement of native plants and sustainable management strategies were investigated. The present results helped to clarify and explain such issues as the adaptability post invasion,interaction and competition between inter-and intra-species and community resistance, thereby providing important references to researches on other invasive alien species.

  3. Business Strategy and Management Control Measures for Success!

    OpenAIRE

    Marshall, Kent; Snygg, Mikael

    2004-01-01

    Background Studying the relationship between strategy and Management Control Systems (MCS) is not a new phenomenon. The main purpose with the MCS has long been to attain the strategic goals that have been set for the organisation. Scholars have therefore argued that MCS should be adapted in harmony to the strategy employed by the company. There exists however little empirical evidence to support this claim. Problem Recent studies shows that the largest problem companies’ face today is that th...

  4. Tsetse Control and Gambian Sleeping Sickness; Implications for Control Strategy.

    Directory of Open Access Journals (Sweden)

    Inaki Tirados

    Full Text Available Gambian sleeping sickness (human African trypanosomiasis, HAT outbreaks are brought under control by case detection and treatment although it is recognised that this typically only reaches about 75% of the population. Vector control is capable of completely interrupting HAT transmission but is not used because it is considered too expensive and difficult to organise in resource-poor settings. We conducted a full scale field trial of a refined vector control technology to determine its utility in control of Gambian HAT.The major vector of Gambian HAT is the tsetse fly Glossina fuscipes which lives in the humid zone immediately adjacent to water bodies. From a series of preliminary trials we determined the number of tiny targets required to reduce G. fuscipes populations by more than 90%. Using these data for model calibration we predicted we needed a target density of 20 per linear km of river in riverine savannah to achieve >90% tsetse control. We then carried out a full scale, 500 km2 field trial covering two HAT foci in Northern Uganda to determine the efficacy of tiny targets (overall target density 5.7/km2. In 12 months, tsetse populations declined by more than 90%. As a guide we used a published HAT transmission model and calculated that a 72% reduction in tsetse population is required to stop transmission in those settings.The Ugandan census suggests population density in the HAT foci is approximately 500 per km2. The estimated cost for a single round of active case detection (excluding treatment, covering 80% of the population, is US$433,333 (WHO figures. One year of vector control organised within the country, which can completely stop HAT transmission, would cost US$42,700. The case for adding this method of vector control to case detection and treatment is strong. We outline how such a component could be organised.

  5. Advanced WEC Dynamics & Controls FY16 Testing Report

    Energy Technology Data Exchange (ETDEWEB)

    Coe, Ryan Geoffrey [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bacelli, Giorgio [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wilson, David G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Patterson, David Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-01

    A model-scale wave tank test was conducted in the interest of improving control systems design of wave energy converters (WECs). The success of most control strategies is based directly upon the availability of a reduced-order model with the ability to capture the dynamics of the system with sufficient accuracy. For this reason, the test described in this report, which is the first in a series of planned tests on WEC controls, focused on system identification (system ID) and model validation.

  6. Control Strategies for the DAB Based PV Interface System.

    Science.gov (United States)

    El-Helw, Hadi M; Al-Hasheem, Mohamed; Marei, Mostafa I

    2016-01-01

    This paper presents an interface system based on the Dual Active Bridge (DAB) converter for Photovoltaic (PV) arrays. Two control strategies are proposed for the DAB converter to harvest the maximum power from the PV array. The first strategy is based on a simple PI controller to regulate the terminal PV voltage through the phase shift angle of the DAB converter. The Perturb and Observe (P&O) Maximum Power Point Tracking (MPPT) technique is utilized to set the reference of the PV terminal voltage. The second strategy presented in this paper employs the Artificial Neural Network (ANN) to directly set the phase shift angle of the DAB converter that results in harvesting maximum power. This feed-forward strategy overcomes the stability issues of the feedback strategy. The proposed PV interface systems are modeled and simulated using MATLAB/SIMULINK and the EMTDC/PSCAD software packages. The simulation results reveal accurate and fast response of the proposed systems. The dynamic performance of the proposed feed-forward strategy outdoes that of the feedback strategy in terms of accuracy and response time. Moreover, an experimental prototype is built to test and validate the proposed PV interface system. PMID:27560138

  7. Control Strategies for the DAB Based PV Interface System

    Science.gov (United States)

    El-Helw, Hadi M.; Al-Hasheem, Mohamed; Marei, Mostafa I.

    2016-01-01

    This paper presents an interface system based on the Dual Active Bridge (DAB) converter for Photovoltaic (PV) arrays. Two control strategies are proposed for the DAB converter to harvest the maximum power from the PV array. The first strategy is based on a simple PI controller to regulate the terminal PV voltage through the phase shift angle of the DAB converter. The Perturb and Observe (P&O) Maximum Power Point Tracking (MPPT) technique is utilized to set the reference of the PV terminal voltage. The second strategy presented in this paper employs the Artificial Neural Network (ANN) to directly set the phase shift angle of the DAB converter that results in harvesting maximum power. This feed-forward strategy overcomes the stability issues of the feedback strategy. The proposed PV interface systems are modeled and simulated using MATLAB/SIMULINK and the EMTDC/PSCAD software packages. The simulation results reveal accurate and fast response of the proposed systems. The dynamic performance of the proposed feed-forward strategy outdoes that of the feedback strategy in terms of accuracy and response time. Moreover, an experimental prototype is built to test and validate the proposed PV interface system. PMID:27560138

  8. Climate Control Load Reduction Strategies for Electric Drive Vehicles in Warm Weather

    Energy Technology Data Exchange (ETDEWEB)

    Jeffers, M. A.; Chaney, L.; Rugh, J. P.

    2015-04-30

    Passenger compartment climate control is one of the largest auxiliary loads on a vehicle. Like conventional vehicles, electric vehicles (EVs) require climate control to maintain occupant comfort and safety, but cabin heating and air conditioning have a negative impact on driving range for all electric vehicles. Range reduction caused by climate control and other factors is a barrier to widespread adoption of EVs. Reducing the thermal loads on the climate control system will extend driving range, thereby reducing consumer range anxiety and increasing the market penetration of EVs. Researchers at the National Renewable Energy Laboratory have investigated strategies for vehicle climate control load reduction, with special attention toward EVs. Outdoor vehicle thermal testing was conducted on two 2012 Ford Focus Electric vehicles to evaluate thermal management strategies for warm weather, including solar load reduction and cabin pre-ventilation. An advanced thermal test manikin was used to assess a zonal approach to climate control. In addition, vehicle thermal analysis was used to support testing by exploring thermal load reduction strategies, evaluating occupant thermal comfort, and calculating EV range impacts. Through stationary cooling tests and vehicle simulations, a zonal cooling configuration demonstrated range improvement of 6%-15%, depending on the drive cycle. A combined cooling configuration that incorporated thermal load reduction and zonal cooling strategies showed up to 33% improvement in EV range.

  9. Recent advances in opinion modeling: control and social influence

    CERN Document Server

    Albi, Giacomo; Toscani, Giuseppe; Zanella, Mattia

    2016-01-01

    We survey some recent developments on the mathematical modeling of opinion dynamics. After an introduction on opinion modeling through interacting multi-agent systems described by partial differential equations of kinetic type, we focus our attention on two major advancements: optimal control of opinion formation and influence of additional social aspects, like conviction and number of connections in social networks, which modify the agents' role in the opinion exchange process.

  10. Control Systems with Saturating Inputs Analysis Tools and Advanced Design

    CERN Document Server

    Corradini, Maria Letizia; Giannoni, Fabio; Orlando, Giuseppe

    2012-01-01

    This series aims to report new developments in the fields of control and information sciences - quickly, informally and at a high level. The type of material considered for publication includes: 1. Preliminary drafts of monographs and advanced textbooks 2. Lectures on a new field, or presenting a new angle on a classical field 3. Research reports 4. Reports of meetings, provided they are a) of exceptional interest and b) devoted to a specific topic. The timeliness of subject material is very important.

  11. Operator’s cognitive, communicative and operative activities based workload measurement of advanced main control room

    International Nuclear Information System (INIS)

    Highlights: • An advanced MMIS in the advanced MCR requires new roles and tasks of operators. • A new workload evaluation framework is needed for a new MMIS environment. • This work suggests a new workload measurement approach (COCOA) for an advanced MCR. • COCOA enables 3-dimensional measurement of cognition, communication and operation. • COCOA workload evaluation of the reference plant through simulation was performed. - Abstract: An advanced man–machine interface system (MMIS) with a computer-based procedure system and high-tech control/alarm system is installed in the advanced main control room (MCR) of a nuclear power plant. Accordingly, though the task of the operators has been changed a great deal, owing to a lack of appropriate guidelines on the role allocation or communication method of the operators, operators should follow the operating strategies of conventional MCR and the problem of an unbalanced workload for each operator can be raised. Thus, it is necessary to enhance the operation capability and improve the plant safety by developing guidelines on the role definition and communication of operators in an advanced MCR. To resolve this problem, however, a method for measuring the workload according to the work execution of the operators is needed, but an applicable method is not available. In this research, we propose a COgnitive, Communicative and Operational Activities measurement approach (COCOA) to measure and evaluate the workload of operators in an advanced MCR. This paper presents the taxonomy for additional operation activities of the operators to use the computerized procedures and soft control added to an advanced MCR, which enables an integrated measurement of the operator workload in various dimensions of cognition, communication, and operation. To check the applicability of COCOA, we evaluated the operator workload of an advanced MCR of a reference power plant through simulation training experiments. As a result, the amount

  12. Mothers' teaching strategies and children's effortful control: a longitudinal study.

    Science.gov (United States)

    Eisenberg, Nancy; Vidmar, Masa; Spinrad, Tracy L; Eggum, Natalie D; Edwards, Alison; Gaertner, Bridget; Kupfer, Anne

    2010-09-01

    Findings on the relation of maternal verbal teaching strategies to children's effortful control (EC; i.e., self-regulation) are limited in quantity and somewhat inconsistent. In this study, children's EC was assessed at 18, 30, and 42 months (ns = 255, 229, and 209, respectively) with adults' reports and a behavioral measure. Mothers' verbal teaching strategies were assessed while the mother and child worked on a task together. Children's general vocabulary also was measured. In a structural panel model taking into account prior levels of constructs and correlations within time, as well as the relations of EC and teaching strategies to children's vocabulary, socioeconomic status, age, and sex of the child, 18-month EC positively predicted mothers' 30-month cognitive assistance and questioning strategies and negatively predicted 30-month maternal directive strategies. In addition, high 30-month EC predicted greater 42-month maternal cognitive assistance and fewer directive strategies. Thus, mothers' teaching strategies were predicted by individual differences in self-regulatory skills, supporting potential evocative child effects on mothers' teaching strategies.

  13. Impact of Machine Learning on Elevator Control Strategies : A comparison of time efficiency for machine learning elevator control strategies and static elevator control strategies in an office building

    OpenAIRE

    Löf, Marcus; Andersson, Elias

    2015-01-01

    Elevators are used in a large amount of buildings all over the world for fast and comfortable transportation. Today it is becoming increasingly important for people and products to be time efficient, and with technological development new solutions are created to answer this rising demand. To do this in an elevator context, elevator control strategies are implementedas optimal as possible. Machine learning is a relatively new concept, but it is already used in attempts to improve the performa...

  14. Turbine Control Strategies for Wind Farm Power Optimization

    DEFF Research Database (Denmark)

    Mirzaei, Mahmood; Göçmen Bozkurt, Tuhfe; Giebel, Gregor;

    2015-01-01

    In recent decades there has been increasing interest in green energies, of which wind energy is the most important one. In order to improve the competitiveness of the wind power plants, there are ongoing researches to decrease cost per energy unit and increase the efficiency of wind turbines...... and wind farms. One way of achieving these goals is to optimize the power generated by a wind farm. One optimization method is to choose appropriate operating points for the individual wind turbines in the farm. We have made three models of a wind farm based on three difference control strategies....... Basically, the control strategies determine the steady state operating points of the wind turbines. Except the control strategies of the individual wind turbines, the wind farm models are similar. Each model consists of a row of 5MW reference wind turbines. In the models we are able to optimize...

  15. A new control strategy of SMES for mitigating subsynchronous oscillations

    Energy Technology Data Exchange (ETDEWEB)

    Farahani, Mohsen, E-mail: m.farahani@basu.ac.ir [Bu-Ali Sina University, Department of Electrical Engineering, Hamedan-Iran (Iran, Islamic Republic of)

    2012-12-14

    This paper proposes a new strategy to mitigate the subsynchronous oscillations in power systems compensated by series capacitors via control of active power of superconducting magnetic energy storage (SMES) unit. The strategy is based on the generator acceleration signal. So, the SMES absorbs or generates the energy imbalance caused by different disturbances in the power system and suppresses the subsynchronous oscillations. The chaotic optimization algorithm (COA) is used to achieve the optimal parameter of the proposed controller. To validate the capability of the SMES in damping oscillations, some simulations with different disturbances are performed on the first model of IEEE second benchmark model. All the simulation results show that the subsynchronous resonance as well as low frequency oscillation (LFO) is satisfactorily mitigated by the SMES controlled by the proposed strategy.

  16. A new control strategy of SMES for mitigating subsynchronous oscillations

    Science.gov (United States)

    Farahani, Mohsen

    2012-12-01

    This paper proposes a new strategy to mitigate the subsynchronous oscillations in power systems compensated by series capacitors via control of active power of superconducting magnetic energy storage (SMES) unit. The strategy is based on the generator acceleration signal. So, the SMES absorbs or generates the energy imbalance caused by different disturbances in the power system and suppresses the subsynchronous oscillations. The chaotic optimization algorithm (COA) is used to achieve the optimal parameter of the proposed controller. To validate the capability of the SMES in damping oscillations, some simulations with different disturbances are performed on the first model of IEEE second benchmark model. All the simulation results show that the subsynchronous resonance as well as low frequency oscillation (LFO) is satisfactorily mitigated by the SMES controlled by the proposed strategy.

  17. Improved safety in advanced control complexes, without side effects

    International Nuclear Information System (INIS)

    If we only look for a moment at the world around us, it is obvious that advances in digital electronic equipment and Human-System Interface (HSI) technology are occurring at a phenomenal pace. This is evidenced from our home entertainment systems to the dashboard and computer-based operation of our new cars. Though the nuclear industry has less vigorously embraced these advances, their application is being implemented through individual upgrades to current generation nuclear plants and as plant-wide control complexes for advanced plants. In both venues modem technology possesses widely touted advantages for improving plant availability as well as safety. The well-documented safety benefits of digital Instrumentation and Controls (I ampersand C) include higher reliability resulting from redundancy and fault tolerance, inherent self-test and self-diagnostic capabilities which have replaced error-prone human tasks, resistance to setpoint drift increasing available operating margins, and the ability to run complex, real-time, computer-based algorithms directly supporting an operator's monitoring and control task requirements. 22 refs., 3 figs., 5 tabs

  18. Guidelines for the review of advanced controls and displays

    International Nuclear Information System (INIS)

    Advanced control room (ACR) concepts are being developed and refined in the commercial nuclear industry as part of future reactor designs. These ACRs will utilize advanced human-system interface (HSI) technologies which may have significant implications for plant safety in that they may affect: (1) the operators' overall role (function) in the system; (2) the methods by which operators receive information about system status; (3) the ways in which the operators interact with the system; and (4) the requirements on operators to understand and supervise an increasingly complex system. The Nuclear Regulatory Commission (NRC) reviews control room designs to ensure that they incorporate good human factors engineering principles so as to support operator performance and reliability necessary to protect public health and safety. The principal guidance available to the NRC (NUREG-0700) was developed more than ten years ago and does not address new technologies. Accordingly, the guidance must be updated. This paper discusses the development of an NRC Advanced Control Room Design Review Guideline

  19. The strategy for intelligent integrated instrumentation and control system development

    International Nuclear Information System (INIS)

    All of the nuclear power plants in Korea are operating with analog instrumentation and control ( I and C) equipment which are increasingly faced with frequent troubles, obsolescence and high maintenance expenses. Electrical and computer technology has improved rapidly in recent years and has been applied to other industries. So it is strongly recommended we adopt modern digital and computer technology to improve plant safety and availability. The advanced I and C system, namely, Integrated Intelligent Instrumentation and Control System (I3 Cs) will be developed for beyond the next generation nuclear power plant. I3CS consists of three major parts, the advanced compact workstation, distributed digital control and protection system including Automatic Start-up/Shutdown Intelligent Control System (ASICS) and the computer-based alarm processing and operator support system, namely, Diagnosis, Response, and operator Aid Management System (DREAMS)

  20. Two-DOF precision platform for spacecraft thrust vector control: control strategies and simulations

    Science.gov (United States)

    Ma, Kougen; Ghasemi-Nejhad, Mehrdad N.

    2004-07-01

    This paper presents control strategies and simulations of a two-DOF precision platform as an adaptive thruster mount structure with precision positioning and active vibration suppression capabilities for thrust vector control of space satellites. First, the configuration of the two-DOF precision platform is introduced, which is an intelligent tripod with two in-plane rotational degrees of freedom for the top device-plate. Precision positioning of this platform is achieved using active members that extend or contract to tilt the top device-plate where the thruster is mounted. Kinematic analysis of the platform is then presented and followed by two control strategies; namely local control strategy and global control strategy. In the local control strategy, the motion of each active member is controlled locally according to the kinematical feature of the platform and the local sensor information to achieve the desired tilt of the top device-plate. In the global control strategy, the motion of each active member is adjusted according to the system level information from a tilt sensor. Fuzzy logic control is employed and the two control strategies are simulated and compared.

  1. Optimal Energy Control Strategy Design for a Hybrid Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Yuan Zou

    2013-01-01

    Full Text Available A heavy-duty parallel hybrid electric truck is modeled, and its optimal energy control is studied in this paper. The fundamental architecture of the parallel hybrid electric truck is modeled feed-forwardly, together with necessary dynamic features of subsystem or components. Dynamic programming (DP technique is adopted to find the optimal control strategy including the gear-shifting sequence and the power split between the engine and the motor subject to a battery SOC-sustaining constraint. Improved control rules are extracted from the DP-based control solution, forming near-optimal control strategies. Simulation results demonstrate that a significant improvement on the fuel economy can be achieved in the heavy-duty vehicle cycle from the natural driving statistics.

  2. Control Systems Cyber Security:Defense in Depth Strategies

    Energy Technology Data Exchange (ETDEWEB)

    David Kuipers; Mark Fabro

    2006-05-01

    Information infrastructures across many public and private domains share several common attributes regarding IT deployments and data communications. This is particularly true in the control systems domain. A majority of the systems use robust architectures to enhance business and reduce costs by increasing the integration of external, business, and control system networks. However, multi-network integration strategies often lead to vulnerabilities that greatly reduce the security of an organization, and can expose mission-critical control systems to cyber threats. This document provides guidance and direction for developing ‘defense-in-depth’ strategies for organizations that use control system networks while maintaining a multi-tier information architecture that requires: Maintenance of various field devices, telemetry collection, and/or industrial-level process systems Access to facilities via remote data link or modem Public facing services for customer or corporate operations A robust business environment that requires connections among the control system domain, the external Internet, and other peer organizations.

  3. Wolbachia: A biological control strategy against arboviral diseases.

    Science.gov (United States)

    Mohanty, Ipsita; Rath, Animesha; Mahapatra, Namita; Hazra, Rupenangshu K

    2016-01-01

    Vector-borne diseases particularly those transmitted by mosquitoes like Dengue are among the leading causes of mortality and morbidity in human population. There are no effective vaccines or treatment against dengue fever till date and the control methods are limited. So, new approaches are urgently in need to reverse these trends. Vector control is currently the primary intervention tool. Strategies that reduce or block pathogen transmission by mosquitoes have been proposed as a means of augmenting current control measures to reduce the growing burden of vector-borne diseases. Wolbachia an endosymbiont of arthropod vectors is being explored as a novel ecofriendly control strategy. Studies in Drosophila have shown that Wolbachia can confer resistance to diverse RNA viruses and protect flies from virus-induced mortality. This review was focused on biology of the Wolbachia and its implication as a control measure for arboviral diseases mainly Dengue and Chikungunya. PMID:27681542

  4. Application of advanced polymeric materials for controlled release pesticides

    Science.gov (United States)

    Rahim, M.; Hakim, M. R.; Haris, H. M.

    2016-08-01

    The objective of this work was to study the capability of advanced polymeric material constituted by chitosan and natural rubber matrices for controlled release of pesticides (1-hydroxynaphthalene and 2-hydroxynaphthalene) in aqueous solution. The released amount of pesticides was measured spectrophotometrically from the absorbance spectra applying a standardized curve. The release of the pesticides was studied into refreshing and non-refreshing neutral aqueous media. Interestingly, formulation successfully indicated a consistent, controlled and prolonged release of pesticides over a period of 35 days.

  5. Optical control of the Advanced Technology Solar Telescope.

    Science.gov (United States)

    Upton, Robert

    2006-08-10

    The Advanced Technology Solar Telescope (ATST) is an off-axis Gregorian astronomical telescope design. The ATST is expected to be subject to thermal and gravitational effects that result in misalignments of its mirrors and warping of its primary mirror. These effects require active, closed-loop correction to maintain its as-designed diffraction-limited optical performance. The simulation and modeling of the ATST with a closed-loop correction strategy are presented. The correction strategy is derived from the linear mathematical properties of two Jacobian, or influence, matrices that map the ATST rigid-body (RB) misalignments and primary mirror figure errors to wavefront sensor (WFS) measurements. The two Jacobian matrices also quantify the sensitivities of the ATST to RB and primary mirror figure perturbations. The modeled active correction strategy results in a decrease of the rms wavefront error averaged over the field of view (FOV) from 500 to 19 nm, subject to 10 nm rms WFS noise. This result is obtained utilizing nine WFSs distributed in the FOV with a 300 nm rms astigmatism figure error on the primary mirror. Correction of the ATST RB perturbations is demonstrated for an optimum subset of three WFSs with corrections improving the ATST rms wavefront error from 340 to 17.8 nm. In addition to the active correction of the ATST, an analytically robust sensitivity analysis that can be generally extended to a wider class of optical systems is presented. PMID:16926876

  6. An Efficient Modal Control Strategy for the Active Vibration Control of a Truss Structure

    Directory of Open Access Journals (Sweden)

    Ricardo Carvalhal

    2007-01-01

    Full Text Available In this paper an efficient modal control strategy is described for the active vibration control of a truss structure. In this approach, a feedback force is applied to each mode to be controlled according to a weighting factor that is determined by assessing how much each mode is excited by the primary source. The strategy is effective provided that the primary source is at a fixed position on the structure, and that the source is stationary in the statistical sense. To test the effectiveness of the control strategy it is compared with an alternative, established approach namely, Independent Modal Space Control (IMSC. Numerical simulations show that with the new strategy it is possible to significantly reduce the control effort required, with a minimal reduction in control performance.

  7. The Advanced Photon Source Injector Test Stand Control System

    CERN Document Server

    MacLean, J F

    2001-01-01

    The Advanced Photon Source (APS) primary and backup injectors consist of two thermionic-cathode rf guns. These guns are being upgraded to provide improved performance, to improve ease of maintenance, and to reduce downtime required for repair or replacement of a failed injector. As part of the process, an injector test stand is being prepared. This stand is effectively independent of the APS linac and will allow for complete characterization and validation of an injector prior to its installation into the APS linac. A modular control system for the test stand has been developed using standard APS control solutions with EPICS to deliver a flexible and comprehensive control system. The modularity of the system will allow both the future expansion of test stand functionality and the evaluation of new control techniques and solutions.

  8. Integrated metrology: an enabler for advanced process control (APC)

    Science.gov (United States)

    Schneider, Claus; Pfitzner, Lothar; Ryssel, Heiner

    2001-04-01

    Advanced process control (APC) techniques become more and more important as short innovation cycles in microelectronics and a highly competitive market requires cost-effective solutions in semiconductor manufacturing. APC marks a paradigm shift from statistically based techniques (SPC) using monitor wafers for sampling measurement data towards product wafer control. The APC functionalities including run-to-run control, fault detection, and fault analysis allow to detect process drifts and excursions at an early stage and to minimize the number of misprocessed wafers. APC is being established as part of factory control systems through the definition of an APC framework. A precondition for APC is the availability of sensors and measurement methods providing the necessary wafer data. This paper discusses integrated metrology as an enabler for APC and demonstrates practical implementations in semiconductor manufacturing.

  9. Analysis of Control Strategies for Aircraft Flight Upset Recovery

    Science.gov (United States)

    Crespo, Luis G.; Kenny, Sean P.; Cox, David E.; Muri, Daniel G.

    2012-01-01

    This paper proposes a framework for studying the ability of a control strategy, consisting of a control law and a command law, to recover an aircraft from ight conditions that may extend beyond the normal ight envelope. This study was carried out (i) by evaluating time responses of particular ight upsets, (ii) by evaluating local stability over an equilibrium manifold that included stall, and (iii) by bounding the set in the state space from where the vehicle can be safely own to wings-level ight. These states comprise what will be called the safely recoverable ight envelope (SRFE), which is a set containing the aircraft states from where a control strategy can safely stabilize the aircraft. By safe recovery it is implied that the tran- sient response stays between prescribed limits before converging to a steady horizontal ight. The calculation of the SRFE bounds yields the worst-case initial state corresponding to each control strategy. This information is used to compare alternative recovery strategies, determine their strengths and limitations, and identify the most e ective strategy. In regard to the control law, the authors developed feedback feedforward laws based on the gain scheduling of multivariable controllers. In regard to the command law, which is the mechanism governing the exogenous signals driving the feed- forward component of the controller, we developed laws with a feedback structure that combines local stability and transient response considera- tions. The upset recovery of the Generic Transport Model, a sub-scale twin-engine jet vehicle developed by NASA Langley Research Center, is used as a case study.

  10. Evaluation of information display at advanced main control room

    Energy Technology Data Exchange (ETDEWEB)

    Min, Dae Hwan; Yu, Seon Jae; Choi, Eui Sun [Korea Univ., Seoul (Korea, Republic of)

    2000-03-15

    This year we plan to survey information in order to have basic understanding of digital information display and control at the advanced MCR. At first we collect different ways of presenting information at the advanced MCR. Secondly, we conduct literature survey on studies that have investigated information representation techniques and their effects. Then, we need compare differences between conventional NPPs and advanced NPPs. Thirdly, we need to check HMI styles and evaluation techniques that are used currently at foreign NPPs. Indeed, HMI at the advanced MCR is quite different from that at a conventional MCR. It is not desirable to apply the same evaluation technique that has veen used at the conventional MCR. We need to develop an evaluation technique that is valid in theory and applicable in practice. Finally, we identify the requirements for a support system for an HMI evaluator, since it is not easy to carry out an evaluation task even though one has firm background on cognitive engineering theories and practical experiences.

  11. Evaluation of information display at advanced main control room

    International Nuclear Information System (INIS)

    This year we plan to survey information in order to have basic understanding of digital information display and control at the advanced MCR. At first we collect different ways of presenting information at the advanced MCR. Secondly, we conduct literature survey on studies that have investigated information representation techniques and their effects. Then, we need compare differences between conventional NPPs and advanced NPPs. Thirdly, we need to check HMI styles and evaluation techniques that are used currently at foreign NPPs. Indeed, HMI at the advanced MCR is quite different from that at a conventional MCR. It is not desirable to apply the same evaluation technique that has veen used at the conventional MCR. We need to develop an evaluation technique that is valid in theory and applicable in practice. Finally, we identify the requirements for a support system for an HMI evaluator, since it is not easy to carry out an evaluation task even though one has firm background on cognitive engineering theories and practical experiences

  12. Refinements and Tests of an Advanced Controller to Mitigate Fatigue Loads in the Controls Advanced Research Turbine: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wright, A.; Fleming, P.

    2010-12-01

    Wind turbines are complex, nonlinear, dynamic systems forced by aerodynamic, gravitational, centrifugal, and gyroscopic loads. The aerodynamics of wind turbines are nonlinear, unsteady, and complex. Turbine rotors are subjected to a complicated 3-D turbulent wind inflow field, with imbedded coherent vortices that drive fatigue loads and reduce lifetime. Design of control algorithms for wind turbines must account for multiple control objectives. Future large multi-megawatt turbines must be designed with lighter weight structures, using active controls to mitigate fatigue loads, while maximizing energy capture. Active damping should be added to these dynamic structures to maintain stability for operation in a complex environment. At the National Renewable Energy Laboratory (NREL), we have designed, implemented, and tested advanced controls to maximize energy extraction and reduce structural dynamic loads. These control designs are based on linear models of the turbine that are generated by specialized modeling software. In this paper, we present field test results of an advanced control algorithm to mitigate blade, tower, and drivetrain loads in Region 3.

  13. Analysis of Control Strategies for Diode Clamped Multilevel Inverter

    Directory of Open Access Journals (Sweden)

    C. R. Balamurugan

    2013-05-01

    Full Text Available This paper presents the comparison of various Pulse Width Modulation (PWM strategies for the three phase Diode Clamped Multi Level Inverter (DCMLI. The main contribution of this paper is the proposal of new modulation schemes with Variable Amplitude (VA and various new schemes adopting the constant switching frequency and also variable switching frequency multicarrier control freedom degree combination concepts are developed and simulated for the chosen three phase DCMLI. The three phase DCMLI, is controlled in this paper with Sinusoidal PWM (SPWM reference along with triangular carriers and analysis is made among both without carrier overlapping and with Carrier Overlapping (CO techniques to choose the better strategy by performing simulation using MATLAB-SIMULINK. The variation of Total Harmonic Distortion (THD and fundamental RMS output voltage is observed for various modulation indices. It is observed that among the various equal amplitude PWM strategies, COPWM-C provides less THD and higher RMS voltage. It is recognized that among the various variable amplitude PWM strategies, VACOPWM-C provides less THD and VACOPWM-B provides higher RMS voltage. By comparing the equal amplitude PWM strategies with the variable amplitude PWM strategies it is inferred that VACOPWM-C provides less THD and VACOPWM-B provides higher RMS voltage. It is also inferred that carrier overlapping techniques provides better results compared to the without carrier overlapping techniques.

  14. Control strategies used in the control software for the Heavy Ion Research Facility in Lanzhou

    Science.gov (United States)

    Zhou, Wen-Xiong; Wang, Yan-Yu; Pan, Liang-Ming; Tu, Sheng-Pan

    2016-07-01

    Automation control systems are important for the operation of an accelerator. To ensure the reliable, stable and flexible operation of the Heavy Ion Research Facility in Lanzhou (HIRFL), several control systems are developed. The developed control systems are the SECRAL control system, the LECR3 control system, the LAPECR1 control system and the Electro-Static septum control system. The corresponding control software systems are developed using Visual C++. To ensure the accuracy, stability and flexibility of the control systems, some special control strategies are developed in the control software systems. This paper provides a detailed description of the main control strategies used in the control software systems. The main control strategies are composed of a reliable communication mechanism, a correct data/command transmission mechanism, an efficient data storage mechanism and an interlock protection mechanism. To guarantee a reliable communication between the devices for the commercially purchased devices and the built in-house ones, a modified heartbeat method is developed. To provide flexible reconstitution function for the control systems, the command queue and the state machine are combined. The message mechanism and the multiple windows mechanism are also used for the module mechanism. The relevant control systems are introduced as examples of these control strategies. These systems have been running stably for several years.

  15. Research on Operation and Control Strategy of 600MW PWR in Load Follow

    International Nuclear Information System (INIS)

    600MW Pressurized Water Reactor (PWR) is designed to operate in Constant Axial Offset Control (CAOC) strategy with base load originally. By calculations over a typical load follow scenario '12-3-6-3 (100-50-100%FP) via the CASMO-4E and SIMULATE-3 package, values of core operating parameter have been examined. With the progress of the nuclear power industry, advanced reactors are considered to have a good performance in load follow, economy and flexibility. Under the premise of fuel loading and structural dimensions unchanged, two independent control rod groups M and AO are used in 600MW pressurized water reactor to provide fine control of both the core reactivity and axial power distribution, which is named ' Improved G strategy .' The influences of different control rod distributions, composition materials, and overlap steps had in power changes have been examined in a comparative study to choose the optimal one.Then we simulate a range of load follow scenarios of the redesigned 600MW core without adjusting soluble boron concentration in the begin, middle and end of first cycle. This paper additionally demonstrated the moderator temperature coefficient and shutdown margin values of the reactor in Improved G strategy to compare with the thermal safety design criteria. It's demonstrated that adequate adjustment of control rod groups enable the core to perform load follow through Improved G strategy in 80% of cycle and save a large volume of liquid effluent particularly toward the end of cycle

  16. Temperature control strategy for a seal fatigue tester

    Directory of Open Access Journals (Sweden)

    M. Związek

    2008-08-01

    Full Text Available Purpose: The aim of the paper is optimization of a control strategy used in a seal fatigue tester.Design/methodology/approach: Analytical approach has been applied to get an understanding of a heat exchange process. It is required to optimize the control process algorithm.Findings: The initial control algorithm has been improved regarding numerous tests under different operating conditions. The final version of the control program allows to maintain the temperature according to the on-off strategy minimizing the temperature oscillations and potential overshoots.Research limitations/implications: It should be considered a new control strategy based on PID controller.Practical implications: The major component of the tester is the heat exchanger. It consists of a tube and embedded pipe circuit feeding with the external heating or cooling medium. The tube is a cylindrical housing where the seals are assembled at both sides. Two main pumps circulate the medium at a specified flow rate and pressure. The temperature is maintained to hold it almost constant during heating and cooling phases. Two thermocouples are placed close to the seals, and the one in the middle of the heat exchanger tube. The tester is equipped with a control system consisting of a PLC controller and LabView data acquisition application. It is possible to control the device remotely through LAN/WAN networks. The LabView application communicates with the controller via software with the use of PPI (Point-To-Point Interface protocol. A new control algorithm has allowed to perform tests according to testing specification without significant overshoots.Originality/value: On-off control algorithm has been proposed for a combined heating-cooling installation rarely using in the industrial solutions.

  17. Artificial Intelligent Control for a Novel Advanced Microwave Biodiesel Reactor

    Science.gov (United States)

    Wali, W. A.; Hassan, K. H.; Cullen, J. D.; Al-Shamma'a, A. I.; Shaw, A.; Wylie, S. R.

    2011-08-01

    Biodiesel, an alternative diesel fuel made from a renewable source, is produced by the transesterification of vegetable oil or fat with methanol or ethanol. In order to control and monitor the progress of this chemical reaction with complex and highly nonlinear dynamics, the controller must be able to overcome the challenges due to the difficulty in obtaining a mathematical model, as there are many uncertain factors and disturbances during the actual operation of biodiesel reactors. Classical controllers show significant difficulties when trying to control the system automatically. In this paper we propose a comparison of artificial intelligent controllers, Fuzzy logic and Adaptive Neuro-Fuzzy Inference System(ANFIS) for real time control of a novel advanced biodiesel microwave reactor for biodiesel production from waste cooking oil. Fuzzy logic can incorporate expert human judgment to define the system variables and their relationships which cannot be defined by mathematical relationships. The Neuro-fuzzy system consists of components of a fuzzy system except that computations at each stage are performed by a layer of hidden neurons and the neural network's learning capability is provided to enhance the system knowledge. The controllers are used to automatically and continuously adjust the applied power supplied to the microwave reactor under different perturbations. A Labview based software tool will be presented that is used for measurement and control of the full system, with real time monitoring.

  18. Artificial Intelligent Control for a Novel Advanced Microwave Biodiesel Reactor

    International Nuclear Information System (INIS)

    Biodiesel, an alternative diesel fuel made from a renewable source, is produced by the transesterification of vegetable oil or fat with methanol or ethanol. In order to control and monitor the progress of this chemical reaction with complex and highly nonlinear dynamics, the controller must be able to overcome the challenges due to the difficulty in obtaining a mathematical model, as there are many uncertain factors and disturbances during the actual operation of biodiesel reactors. Classical controllers show significant difficulties when trying to control the system automatically. In this paper we propose a comparison of artificial intelligent controllers, Fuzzy logic and Adaptive Neuro-Fuzzy Inference System(ANFIS) for real time control of a novel advanced biodiesel microwave reactor for biodiesel production from waste cooking oil. Fuzzy logic can incorporate expert human judgment to define the system variables and their relationships which cannot be defined by mathematical relationships. The Neuro-fuzzy system consists of components of a fuzzy system except that computations at each stage are performed by a layer of hidden neurons and the neural network's learning capability is provided to enhance the system knowledge. The controllers are used to automatically and continuously adjust the applied power supplied to the microwave reactor under different perturbations. A Labview based software tool will be presented that is used for measurement and control of the full system, with real time monitoring.

  19. Advanced discrete-time control designs and applications

    CERN Document Server

    Abidi, Khalid

    2015-01-01

    This book covers a wide spectrum of systems such as linear and nonlinear multivariable systems as well as control problems such as disturbance, uncertainty and time-delays. The purpose of this book is to provide researchers and practitioners a manual for the design and application of advanced discrete-time controllers.  The book presents six different control approaches depending on the type of system and control problem. The first and second approaches are based on Sliding Mode control (SMC) theory and are intended for linear systems with exogenous disturbances. The third and fourth approaches are based on adaptive control theory and are aimed at linear/nonlinear systems with periodically varying parametric uncertainty or systems with input delay. The fifth approach is based on Iterative learning control (ILC) theory and is aimed at uncertain linear/nonlinear systems with repeatable tasks and the final approach is based on fuzzy logic control (FLC) and is intended for highly uncertain systems with heuristi...

  20. Integration of advanced teleoperation technologies for control of space robots

    Science.gov (United States)

    Stagnaro, Michael J.

    1993-01-01

    Teleoperated robots require one or more humans to control actuators, mechanisms, and other robot equipment given feedback from onboard sensors. To accomplish this task, the human or humans require some form of control station. Desirable features of such a control station include operation by a single human, comfort, and natural human interfaces (visual, audio, motion, tactile, etc.). These interfaces should work to maximize performance of the human/robot system by streamlining the link between human brain and robot equipment. This paper describes development of a control station testbed with the characteristics described above. Initially, this testbed will be used to control two teleoperated robots. Features of the robots include anthropomorphic mechanisms, slaving to the testbed, and delivery of sensory feedback to the testbed. The testbed will make use of technologies such as helmet mounted displays, voice recognition, and exoskeleton masters. It will allow tor integration and testing of emerging telepresence technologies along with techniques for coping with control link time delays. Systems developed from this testbed could be applied to ground control of space based robots. During man-tended operations, the Space Station Freedom may benefit from ground control of IVA or EVA robots with science or maintenance tasks. Planetary exploration may also find advanced teleoperation systems to be very useful.

  1. Artificial Intelligent Control for a Novel Advanced Microwave Biodiesel Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Wali, W A; Hassan, K H; Cullen, J D; Al-Shamma' a, A I; Shaw, A; Wylie, S R, E-mail: w.wali@2009.ljmu.ac.uk [Built Environment and Sustainable Technologies Institute (BEST), School of the Built Environment, Faculty of Technology and Environment Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom)

    2011-08-17

    Biodiesel, an alternative diesel fuel made from a renewable source, is produced by the transesterification of vegetable oil or fat with methanol or ethanol. In order to control and monitor the progress of this chemical reaction with complex and highly nonlinear dynamics, the controller must be able to overcome the challenges due to the difficulty in obtaining a mathematical model, as there are many uncertain factors and disturbances during the actual operation of biodiesel reactors. Classical controllers show significant difficulties when trying to control the system automatically. In this paper we propose a comparison of artificial intelligent controllers, Fuzzy logic and Adaptive Neuro-Fuzzy Inference System(ANFIS) for real time control of a novel advanced biodiesel microwave reactor for biodiesel production from waste cooking oil. Fuzzy logic can incorporate expert human judgment to define the system variables and their relationships which cannot be defined by mathematical relationships. The Neuro-fuzzy system consists of components of a fuzzy system except that computations at each stage are performed by a layer of hidden neurons and the neural network's learning capability is provided to enhance the system knowledge. The controllers are used to automatically and continuously adjust the applied power supplied to the microwave reactor under different perturbations. A Labview based software tool will be presented that is used for measurement and control of the full system, with real time monitoring.

  2. Seismic isolation of Advanced LIGO gravitational waves detectors: Review of strategy, instrumentation, and performance

    CERN Document Server

    Matichard, F; Mittleman, R; Mason, K; Kissel, J; McIver, J; Abbott, B; Abbott, R; Abbott, S; Allwine, E; Barnum, S; Birch, J; Biscans, S; Celerier, C; Clark, D; Coyne, D; DeBra, D; DeRosa, R; Evans, M; Foley, S; Fritschel, P; Giaime, J A; Gray, C; Grabeel, G; Hanson, J; Hardham, C; Hillard, M; Hua, W; Kucharczyk, C; Landry, M; Roux, A Le; Lhuillier, V; Macleod, D; Macinnis, M; Mitchell, R; Reilly, B O; Ottaway, D; Paris, H; Pele, A; Puma, M; Radkins, H; Ramet, C; Robinson, M; Ruet, L; Sarin, P; Shoemaker, D; Stein, A; Thomas, J; Vargas, M; Venkateswara, K; Warner, J; Wen, S

    2015-01-01

    Isolating ground-based interferometric gravitational wave observatories from environmental disturbances is one of the great challenges of the advanced detector era. In order to directly observe gravitational waves, the detector components and test masses must be highly inertially decoupled from the ground motion not only to sense the faint strain of space-time induced by gravitational waves, but also to maintain the resonance of the very sensitive 4 km interferometers. This article presents the seismic isolation instrumentation and strategy developed for Advanced LIGO interferometers. It reviews over a decade of research on active isolation in the context of gravitational wave detection, and presents the performance recently achieved with the Advanced LIGO observatory. Lastly, it discusses prospects for future developments in active seismic isolation and the anticipated benefits to astrophysical gravitational wave searches. Beyond gravitational wave research, the goal of this article is to provide detailed is...

  3. Automated Demand Response Strategies and Commissioning CommercialBuilding Controls

    Energy Technology Data Exchange (ETDEWEB)

    Piette, Mary Ann; Watson, David; Motegi, Naoya; Kiliccote, Sila; Linkugel, Eric

    2006-05-01

    California electric utilities have been exploring the use of dynamic critical peak pricing (CPP) and other demand response programs to help reduce peaks in customer electric loads. CPP is a new electricity tariff design to promote demand response. This paper begins with a brief review of terminology regarding energy management and demand response, followed by a discussion of DR control strategies and a preliminary overview of a forthcoming guide on DR strategies. The final section discusses experience to date with these strategies, followed by a discussion of the peak electric demand savings from the 2005 Automated CPP program. An important concept identified in the automated DR field tests is that automated DR will be most successful if the building commissioning industry improves the operational effectiveness of building controls. Critical peak pricing and even real time pricing are important trends in electricity pricing that will require new functional tests for building commissioning.

  4. Sustainability, Strategy and Management Control: A Review of the Literature

    OpenAIRE

    Crutzen, Nathalie; Herzig, Christian

    2012-01-01

    The purpose of this research is to explore the emerging body of literature on the relationship between sustainability, strategy and management control. Our way to organise and present the literature aims to both structure the state of our knowledge in this area and stimulate others to contribute to a shared and better understanding of this field of research. Previous research has underlined that (sustainability) management control systems play a key role in shaping processes of (sustaina...

  5. Control strategies for DFIG wind turbines under grid fault conditions

    OpenAIRE

    Luna Alloza, Álvaro; Rolán Blanco, Alejandro; de Medeiros, G.; Rodríguez Cortés, Pedro; Teodorescu, R.

    2009-01-01

    The classical control techniques for regulating the active and reactive power delivery in doubly fed induction generators (DFIG), for wind power applications, are normally based on voltage oriented control (VOC) strategies. Among these algorithms, those that work in a synchronous reference frame, attached to the magnetic flux vector, became very popular. In spite of the good behaviour of such algorithms their performance depends highly on an accurate detection of the s...

  6. Advances in tokamak control: from multi-actuator MHD control to model-based current profile tailoring

    Science.gov (United States)

    Felici, Federico

    2012-10-01

    Recent experiments on TCV have demonstrated integrated control of the sawtooth and Neoclassical Tearing Mode (NTM) instabilities in a combined preemption-suppression strategy. This strategy is enabled by new sawtooth control methods (sawtooth pacing) in which modulation of sawtooth-stabilizing electron cyclotron power during the sawtooth cycle stimulates the advent of the crash. Rather than controlling the average sawtooth period, the precise timing of each individual crash can now be prescribed. Using this knowledge, efficient preemptive stabilization of NTMs becomes possible by applying power on the rational surface only at the instant of the crash-generating seed island. TCV experiments demonstrate that this approach, reinforced by NTM stabilization as a backup strategy, is effectively failsafe. This opens the road to inductive H-mode scenarios with long sawteeth providing longer inter-crash periods of high density and temperature. Also Edge Localized Modes are susceptible to EC modulation and it is shown that individual ELM events can be controlled using similar techniques. For advanced tokamak scenarios, MHD control is to be combined with optimization and control of the plasma kinetic and magnetic profile evolution in time. Real-time simulation of a physical model (RAPTOR) of current transport, including bootstrap current, neoclassical conductivity and auxiliary current drive, yields complete knowledge of the relevant profiles at any given time. The pilot implementation on TCV shows that these calculations can indeed be done in real-time and the resulting profiles have been included in feedback control schemes. Integration of this model with time-varying equilibria and internal current profile diagnostics provides a new framework for real-time interpretation of diagnostic data for plasma prediction, scenario monitoring, disruption prevention and feedback control.

  7. Introduction to the special issue on Advances in intelligent nonlinear control for robotic systems

    Institute of Scientific and Technical Information of China (English)

    Chee Khiang PANG; Huajin TANG; Qing Wei JIA

    2010-01-01

    @@ In the last two decades, robotic systems have achieved wide applications in every aspect of human society, including industrial manufacturing, automotive production, medical devices, and social lives. With the diversity of application do-mains, control techniques have pervaded from industrial robot manipulators, wheeled or legged mobile robots, unmanned autonomous aerial, ground, and underwater vehicles, to humanoid robots, and haptic devices, etc. The growing number of applications of robotics and increasing requirements for system stability, reliability, and safety, are posing new and challenging theoretical and technological problems for modeling and control of these highly nonlinear systems. Control of these complex systems is highly challenging due to the inherent nonlinear response and strong heterogeneity in dif-ferent parts as computers, sensors, hardware objects, etc. As such, novel nonlinear control strategies are essential to the advancement of robotic systems and corresponding technologies.

  8. Advanced nitrogen removal by pulsed sequencing batch reactors (SBR) with real-time control

    Institute of Scientific and Technical Information of China (English)

    YANG Qing; PENG Yongzhen; YANG Anming; GUO Jianhua; LI Jianfeng

    2007-01-01

    The feasibility of pH and oxidation reduction potential (ORP) as on-line control parameters to advance nitrogen removal in pulsed sequencing batch reactors (SBR)was evaluated.The pulsed SBR,a novel operational mode of SBR,was utilized to treat real municipal wastewater accompanied with adding ethanol as external carbon source.It was observed that the bending-point (apex and knee) of pH and ORP profiles can be used to control denitrification process at a low influent C/N ratio while dpH/dt can be used to control the nitrification and denitrification process at a high influent C/N ratio.The experimental results demonstrated that the effluent total nitrogen can be reduced to lower than 2 mg/L,and the average total nitrogen (TN) removal efficiency was higher than 98% by using real-time controll strategy.

  9. 40 CFR 52.785 - Control strategy: Carbon monoxide.

    Science.gov (United States)

    2010-07-01

    ... monoxide national ambient air quality standard. (c) Approval—The Indiana Department of Environmental... National Ambient Air Quality Standard (NAAQS) for Lake and Marion Counties for an additional ten years. ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Carbon monoxide....

  10. 40 CFR 52.2332 - Control Strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control Strategy: Ozone. 52.2332...: Ozone. Determinations—EPA is determining that, as of July 18, 1995, the Salt Lake and Davis Counties ozone nonattainment area has attained the ozone standard based on air quality monitoring data from...

  11. 40 CFR 52.1023 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... for purposes of satisfying the 5 percent increment of progress requirement of 40 CFR 51.905(a)(1)(ii... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1023...: Ozone. (a) Determination. EPA is determining that, as of July 21, 1995, the Lewiston-Auburn...

  12. 40 CFR 52.977 - Control strategy and regulations: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy and regulations: Ozone... and regulations: Ozone. Determination of Attainment. Effective March 12, 2010 EPA has determined the Baton Rouge 1-hour ozone nonattainment area has attained the 1-hour ozone National Ambient Air...

  13. 40 CFR 52.1982 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1982 Section 52.1982 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...: Ozone. (a) Part D—Approval. (1) The Salem/ Portland and Medford/Ashland area attainment plans...

  14. 40 CFR 52.1683 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    ... of EPA's ozone implementation rule (see 40 CFR 51.918), this determination suspends the reasonable... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1683...: Ozone. (a) The State of New York has certified to the satisfaction of the EPA that no sources...

  15. 40 CFR 52.1885 - Control strategy: Ozone.

    Science.gov (United States)

    2010-07-01

    .... Editorial Note: For Federal Register citations affecting § 52.1885, see the List of CFR Sections Affected... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Ozone. 52.1885...: Ozone. (a) Part D—Approval. The following portions of the Ohio plan are approved: (1) The ozone...

  16. 40 CFR 123.46 - Individual control strategies.

    Science.gov (United States)

    2010-07-01

    ... satisfies the criteria for listing under CWA section 304(l) and 40 CFR 130.10(d)(6). (e) If the Regional... CFR part 122, including § 122.44(d). At any time after the Regional Administrator disapproves an ICS... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Individual control strategies....

  17. Control strategies for brushless doubly fed reluctance machines

    OpenAIRE

    Jovanovic, Milutin; Betz, Robert

    2001-01-01

    Paper presents the development and results of comprehensive comparative analysis of different vector control strategies for performance optimisation of the BDFRM being considered as a viable cost-effective brushless alternative to traditional brush and less reliable solutions in applications with limited variable speed ranges (such as wind turbines). Australian Research Council and EPSRC projects.

  18. 40 CFR 52.1081 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... 1997 PM2.5 NAAQS has attained the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 52..., in accordance with 40 CFR 52.1004(c), suspend the requirements for this area to submit an attainment... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate...

  19. 40 CFR 52.2059 - Control strategy: Particulate matter.

    Science.gov (United States)

    2010-07-01

    ... the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 52.1004(c), suspends the... nonattainment areas have clean data for the 1997 PM2.5 NAAQS. This determination, in accordance with 40 CFR 52... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate...

  20. Managing Work and Family: Do Control Strategies Help?

    Science.gov (United States)

    Versey, H. Shellae

    2015-01-01

    How can we effectively manage competing obligations from work and family without becoming overwhelmed? This question inspires the current study by examining control strategies that may facilitate better work-life balance, with a specific focus on the role of lowered aspirations and positive reappraisals, attitudes that underlie adaptive coping…

  1. Bumpless Transfer Between Advanced Controllers with Applications to Power Plant Control

    DEFF Research Database (Denmark)

    Bendtsen, Jan Dimon; Stoustrup, Jakob; Trangbæk, Klaus

    2003-01-01

    This paper deals with bumpless transfer between a number of advanced controllers, e.g. in a gain-scheduling architecture. Linear observer-based controllers are designed for a number of linear approximations of the system model in a set of operating points, and gain scheduling control can subseque......This paper deals with bumpless transfer between a number of advanced controllers, e.g. in a gain-scheduling architecture. Linear observer-based controllers are designed for a number of linear approximations of the system model in a set of operating points, and gain scheduling control can....... In this paper we propose a systematic approach to achieve bumpless transfer between different nominal controllers. The approach is tested on a simple, but highly nonlinear model of a coal-fired power plant....

  2. Concept of advanced back-up control panel design of digital control room

    International Nuclear Information System (INIS)

    Back-up control panel (BCP) of digital main control room (DMCR) is the back-up means for main computerized control means (MCM). This paper focus on technical issues for advanced design of back-up panel (BCP) for CPR1000 using qualified computer-based video display unit to display plant process indication and alarms. Human factors engineering (HFE) issues also have been considered in the BCP design. Then, as the mean to fulfill safety target of nuclear power plant (NPP), an ideal ergonomic design method is exploited for advanced BCP design. (author)

  3. Robust antisynchronization of chaos using sliding mode control strategy

    Indian Academy of Sciences (India)

    Amit Mondal; Mitul Islam; Nurul Islam

    2015-01-01

    The paper proposes a sliding mode control strategy-based scheme for achieving anti-synchronization between two coupled non-linear chaotic systems. The method works irrespective of whether the systems under consideration possess or lack inverse symmetry. Using a linear sliding surface, a sliding mode control input and a non-linear coupling function are designed that synchronizes the systems antiphase. Finite-time convergence of the method is established. The controller is also robust to all forms of bounded perturbations and this robustness can be easily achieved by tuning of a single controller parameter and introduction of a control vector. The controller is also made chattering-free by producing a continuous analogue of the discontinuous control input. The effectiveness of the method is established by implementing it to antisynchronize chaotic Sprott systems and Rossler systems. The results are also verified through numerical simulation work.

  4. Transmission heterogeneity and control strategies for infectious disease emergence.

    Directory of Open Access Journals (Sweden)

    Luca Bolzoni

    Full Text Available BACKGROUND: The control of emergence and spread of infectious diseases depends critically on the details of the genetic makeup of pathogens and hosts, their immunological, behavioral and ecological traits, and the pattern of temporal and spatial contacts among the age/stage-classes of susceptible and infectious host individuals. METHODS AND FINDINGS: We show that failing to acknowledge the existence of heterogeneities in the transmission rate among age/stage-classes can make traditional eradication and control strategies ineffective, and in some cases, policies aimed at controlling pathogen emergence can even increase disease incidence in the host. When control strategies target for reduction in numbers those subsets of the population that effectively limit the production of new susceptible individuals, then control can produce a flush of new susceptibles entering the population. The availability of a new cohort of susceptibles may actually increase disease incidence. We illustrate these general points using Classical Swine Fever as a reference disease. CONCLUSION: Negative effects of culling are robust to alternative formulations of epidemiological processes and underline the importance of better assessing transmission structure in the design of wildlife disease control strategies.

  5. PREFACE: European Workshop on Advanced Control and Diagnosis

    Science.gov (United States)

    Schulte, Horst; Georg, Sören

    2014-12-01

    The European Workshop on Advanced Control and Diagnosis is an annual event that has been organised since 2003 by Control Engineering departments of several European universities in Germany, France, the UK, Poland, Italy, Hungary and Denmark. The overall planning of the workshops is conducted by the Intelligent Control and Diagnosis (ICD) steering committee. This year's ACD workshop took place at HTW Berlin (University of Applied Sciences) and was organised by the Control Engineering group of School of Engineering I of HTW Berlin. 38 papers were presented at ACD 2014, with contributions spanning a variety of fields in modern control science: Discrete control, nonlinear control, model predictive control, system identification, fault diagnosis and fault-tolerant control, control applications, applications of fuzzy logic, as well as modelling and simulation, the latter two forming a basis for all tasks in modern control. Three interesting and high-quality plenary lectures were delivered. The first plenary speaker was Wolfgang Weber from Pepperl+Fuchs, a German manufacturer of state-of-the-art industrial sensors and process interfaces. The second and third plenary speakers were two internationally high-ranked researchers in their respective fields, Prof. Didier Theilliol from Université de Lorraine and Prof. Carsten Scherer from Universität Stuttgart. Taken together, the three plenary lectures sought to contribute to closing the gap between theory and applications. On behalf of the whole ACD 2014 organising committee, we would like to thank all those who submitted papers and participated in the workshop. We hope it was a fruitful and memorable event for all. Together we are looking forward to the next ACD workshop in 2015 in Pilsen, Czech Republic. Horst Schulte (General Chair), Sören Georg (Programme Chair)

  6. Advances and applications in sliding mode control systems

    CERN Document Server

    Zhu, Quanmin

    2015-01-01

    This book describes the advances and applications in Sliding mode control (SMC) which is widely used as a powerful method to tackle uncertain nonlinear systems. The book is organized into 21 chapters which have been organised by the editors to reflect the various themes of sliding mode control. The book provides the reader with a broad range of material from first principles up to the current state of the art in the area of SMC and observation presented in a clear, matter-of-fact style. As such it is appropriate for graduate students with a basic knowledge of classical control theory and some knowledge of state-space methods and nonlinear systems. The resulting design procedures are emphasized using Matlab/Simulink software.    

  7. Advanced Fuzzy Logic Based Admission Control for UMTS System

    Directory of Open Access Journals (Sweden)

    P. Kejik

    2010-12-01

    Full Text Available The capacity of CDMA (Code Division Multiple Access systems is interference limited. Therefore radio resources management (RRM functions are used. They are responsible for supplying optimum coverage, ensuring efficient use of physical resources, and providing the maximum planned capacity. This paper deals with admission control techniques for UMTS (Universal Mobile Telecommunication System. A UMTS system model and four fuzzy logic based admission control algorithms are presented in this paper. Two new versions of fuzzy logic based admission control algorithms are presented there. All algorithms are mutually compared via simulations. Simulations show that the novel advanced fuzzy algorithm outperforms the other simulated algorithms (in terms of blocking probability, dropping probability and the number of active UEs in cell.

  8. Dynamic simulation and study of Mechanical Shim (MSHIM) core control strategy for AP1000 reactor

    International Nuclear Information System (INIS)

    Highlights: • A reactor core fast simulation program RCFSP is developed for AP1000. • A nodal core model and the MSHIM control strategy are implemented in RCFSP. • Load follow results for the original and revised MSHIM strategies are given. • Parameter sensitivity analysis and optimization of MSHIM control system are performed. - Abstract: The advanced Mechanical Shim (MSHIM) core control strategy is implemented in the AP1000 reactor by a digital rod control system. This control system comprises of two separate rod controllers that automatically control the core reactivity and axial power distribution using the gray and black M control banks and the axial offset (AO) control bank respectively. It has been demonstrated that the MSHIM control system can provide superior reactor control capabilities via automatic rod control only, which needs it to take more burdens than many other traditional core control systems during load change transients. This paper presents the dynamic simulation, and the parameter sensitivity analysis and optimization of the MSHIM control system for AP1000 reactor. A nodal core model is used to describe the dynamic behavior of the reactor core first. Then the nodal model and the original and revised MSHIM strategies are implemented in the AP1000 reactor to develop a fast simulation program in MATLAB/SIMULINK. Based on the simulation program, the MSHIM load follow and load regulation operations are simulated, the results of which demonstrate that the core reactivity and axial power distribution can be well-controlled via automatic rod control only. To show the effects of key factors on the control system behavior, the MSHIM load follow simulations with different control parameter values are performed. According to the simulation results and subsequent quantitative analysis, the mechanisms by which the key factors affect the control system behavior are illustrated and the optimum numerical ranges of these parameters are obtained. These

  9. Advances in BAC-Based Physical Mapping and Map Integration Strategies in Plants

    Directory of Open Access Journals (Sweden)

    Ruvini Ariyadasa

    2012-01-01

    Full Text Available In the advent of next-generation sequencing (NGS platforms, map-based sequencing strategy has been recently suppressed being too expensive and laborious. The detailed studies on NGS drafts alone indicated these assemblies remain far from gold standard reference quality, especially when applied on complex genomes. In this context the conventional BAC-based physical mapping has been identified as an important intermediate layer in current hybrid sequencing strategy. BAC-based physical map construction and its integration with high-density genetic maps have benefited from NGS and high-throughput array platforms. This paper addresses the current advancements of BAC-based physical mapping and high-throughput map integration strategies to obtain densely anchored well-ordered physical maps. The resulted maps are of immediate utility while providing a template to harness the maximum benefits of the current NGS platforms.

  10. Cost Effectiveness Analysis of Optimal Malaria Control Strategies in Kenya

    Directory of Open Access Journals (Sweden)

    Gabriel Otieno

    2016-03-01

    Full Text Available Malaria remains a leading cause of mortality and morbidity among the children under five and pregnant women in sub-Saharan Africa, but it is preventable and controllable provided current recommended interventions are properly implemented. Better utilization of malaria intervention strategies will ensure the gain for the value for money and producing health improvements in the most cost effective way. The purpose of the value for money drive is to develop a better understanding (and better articulation of costs and results so that more informed, evidence-based choices could be made. Cost effectiveness analysis is carried out to inform decision makers on how to determine where to allocate resources for malaria interventions. This study carries out cost effective analysis of one or all possible combinations of the optimal malaria control strategies (Insecticide Treated Bednets—ITNs, Treatment, Indoor Residual Spray—IRS and Intermittent Preventive Treatment for Pregnant Women—IPTp for the four different transmission settings in order to assess the extent to which the intervention strategies are beneficial and cost effective. For the four different transmission settings in Kenya the optimal solution for the 15 strategies and their associated effectiveness are computed. Cost-effective analysis using Incremental Cost Effectiveness Ratio (ICER was done after ranking the strategies in order of the increasing effectiveness (total infections averted. The findings shows that for the endemic regions the combination of ITNs, IRS, and IPTp was the most cost-effective of all the combined strategies developed in this study for malaria disease control and prevention; for the epidemic prone areas is the combination of the treatment and IRS; for seasonal areas is the use of ITNs plus treatment; and for the low risk areas is the use of treatment only. Malaria transmission in Kenya can be minimized through tailor-made intervention strategies for malaria control

  11. Stability and control issues associated with lightly loaded rotors autorotating in high advance ratio flight

    Science.gov (United States)

    Rigsby, James Michael

    sensitivities with advance ratio, and advance ratio dependent control cross coupling. Hub moment response to rotor disturbances results in transients where rotor damping is reduced due to low Lock number blades and reduced rotor angular velocity. Experimentally identified frequency response shows dominant low frequency modes with advance ratio dependent damping and the frequencies are on the order of typical airframe modes. Rotor speed response to swashplate control perturbations from trim results in non-linear behavior that is advance ratio dependent, and which stems from cyclic flapping behavior at high advance ratio. Rotor control strategies were developed including the use of variable shaft incidence to achieve rotor speed control with hub moment suppression achieved through cyclic control. Flight dynamics characteristics resulting from the coupling of the rotor and airframe were predicted in flight using a baseline airframe with conventional fixed-wing controls, representative of the current interest in the concept vehicle. Results predicted by linearization of the non-linear models were compared with system identification results using the non-linear simulation as surrogate flight test data. Low frequency rotor response is shown to couple with the vehicle motion for short period and roll mode response to airframe control inputs. The rotor speed mode is shown to couple with short period and long period vehicle modes as the rotor torque balance is sensitive to vehicle speed and attitude changes.

  12. Do biological-based strategies hold promise to biofouling control in MBRs?

    KAUST Repository

    Malaeb, Lilian

    2013-10-01

    Biofouling in membrane bioreactors (MBRs) remains a primary challenge for their wider application, despite the growing acceptance of MBRs worldwide. Research studies on membrane fouling are extensive in the literature, with more than 200 publications on MBR fouling in the last 3 years; yet, improvements in practice on biofouling control and management have been remarkably slow. Commonly applied cleaning methods are only partially effective and membrane replacement often becomes frequent. The reason for the slow advancement in successful control of biofouling is largely attributed to the complex interactions of involved biological compounds and the lack of representative-for-practice experimental approaches to evaluate potential effective control strategies. Biofouling is driven by microorganisms and their associated extra-cellular polymeric substances (EPS) and microbial products. Microorganisms and their products convene together to form matrices that are commonly treated as a black box in conventional control approaches. Biological-based antifouling strategies seem to be a promising constituent of an effective integrated control approach since they target the essence of biofouling problems. However, biological-based strategies are in their developmental phase and several questions should be addressed to set a roadmap for translating existing and new information into sustainable and effective control techniques. This paper investigates membrane biofouling in MBRs from the microbiological perspective to evaluate the potential of biological-based strategies in offering viable control alternatives. Limitations of available control methods highlight the importance of an integrated anti-fouling approach including biological strategies. Successful development of these strategies requires detailed characterization of microorganisms and EPS through the proper selection of analytical tools and assembly of results. Existing microbiological/EPS studies reveal a number of

  13. Do biological-based strategies hold promise to biofouling control in MBRs?

    Science.gov (United States)

    Malaeb, Lilian; Le-Clech, Pierre; Vrouwenvelder, Johannes S; Ayoub, George M; Saikaly, Pascal E

    2013-10-01

    Biofouling in membrane bioreactors (MBRs) remains a primary challenge for their wider application, despite the growing acceptance of MBRs worldwide. Research studies on membrane fouling are extensive in the literature, with more than 200 publications on MBR fouling in the last 3 years; yet, improvements in practice on biofouling control and management have been remarkably slow. Commonly applied cleaning methods are only partially effective and membrane replacement often becomes frequent. The reason for the slow advancement in successful control of biofouling is largely attributed to the complex interactions of involved biological compounds and the lack of representative-for-practice experimental approaches to evaluate potential effective control strategies. Biofouling is driven by microorganisms and their associated extra-cellular polymeric substances (EPS) and microbial products. Microorganisms and their products convene together to form matrices that are commonly treated as a black box in conventional control approaches. Biological-based antifouling strategies seem to be a promising constituent of an effective integrated control approach since they target the essence of biofouling problems. However, biological-based strategies are in their developmental phase and several questions should be addressed to set a roadmap for translating existing and new information into sustainable and effective control techniques. This paper investigates membrane biofouling in MBRs from the microbiological perspective to evaluate the potential of biological-based strategies in offering viable control alternatives. Limitations of available control methods highlight the importance of an integrated anti-fouling approach including biological strategies. Successful development of these strategies requires detailed characterization of microorganisms and EPS through the proper selection of analytical tools and assembly of results. Existing microbiological/EPS studies reveal a number of

  14. Advances in control of ectoparasites in large animals.

    Science.gov (United States)

    Hiepe, T

    1988-11-01

    In continuation of a publication on "Large-scale management systems and parasite populations: ectoparasites" in Vet. Parasitol. 11 (1982): 61-68, advances and present state of the control of ectoparasites in herds of cattle, sheep and camels are discussed. An intensified animal production necessitates permanent veterinary control of the status of ectoparasites. Strategically, control is basically directed towards achieving three aims: eradication, reduction of losses by means of dilution of ectoparasites regulations, and therapeutic measures. In the last few years, important progress has been made in effective ectoparasites control, mainly resulting from the discovery of new insecticides and acaricides, the improvement of the application techniques and the recent results in the biological control of arthropods; finally, an immunological approach will open new alternative ways of control. The control of mange and demodicosis in cattle; sarcoptic mange and sucking lice infestations in pigs; mange, biting lice infestations and nasal bots in sheep; ectoparasite infestations in camels and tick infestations are the main topics of the paper. The discovery of Ivermectin, a derivate of Streptomyces avermitilis which is now already fully integrated in to the spectrum of antiparasitic drugs, created a new generation of broad spectrum insecticides/acaricides. Current problems of the chemical control of arthropods, like the risk of residues in meat, milk and their products, the insecticide resistance and the possible environment pollution are critically outlined. But on the other hand, it can be predicted hypothetically that the amount of pest control measures in farm animals will increase in the near future to eliminate arthropods as causes of skin diseases and of damages to hides entailing negative effects on leather processing and as vectors of important infection agents. Finally, the proposal is submitted to elaborate international control programmes against ectoparasite

  15. Control Strategy of a Two-Lap Connection Converter

    Institute of Scientific and Technical Information of China (English)

    QUAN Ji-nan; WANG Cong

    2007-01-01

    Two-lap sequential control converters are usually adopted to supply and improve the power factor of input side. The line harmonic damage generated by a sequential control thyristor converter can be serious. To solve this problem and seek an optimum control strategy, we derived the changeable regular of the line-input-current, the fundamental-frequency-current, the harmonic-current-content and the harmonic total distortion ratio of the converter at different firing angles. We obtained relevant data from experiments with a sequential control system of a DC 2.2kW/220V motor. With the example of the operating condition of a DC mine elevator, the harmonic current is two times approximately in sequential control compared to synchronous control when the firing angle of the two converters differs in 30°. At different operating states of a two-lap connection converter, the ideal strategy is an exchange between sequential control and synchronous control, by which we can achieve the complementary goal of improving the power factor and harmonic effect. All analytical conclusions are supported by simulation and experimental results.

  16. Optimal design of coordination control strategy for distributed generation system

    Institute of Scientific and Technical Information of China (English)

    WANG Ai-hua; Norapon Kanjanapadit

    2009-01-01

    This paper presents a novel design procedure for optimizing the power distribution strategy in distributed generation system. A coordinating controller, responsible to distribute the total load power request among multiple DG units, is suggested based on the conception of hierarchical control structure in the dynamic system.The optimal control problem was formulated as a nonlinear optimization problem subject to set of constraints.The resulting problem was solved using the Kutm-Tucker method. Computer simulation results demonstrate that the proposed method can provide better efficiency in terms of reducing total costs compared to existing methods.In addition, the proposed optimal load distribution strategy can be easily implemented in real-time thanks to the simplicity of closed-form solutions.

  17. Mine-Hoist Active Fault Tolerant Control System and Strategy

    Institute of Scientific and Technical Information of China (English)

    WANG Zhi-jie; WANG Yao-cai; MENG Jiang; ZHAO Peng-cheng; CHANG Yan-wei

    2005-01-01

    Based on fault diagnosis and fault tolerant technologies, the mine-hoist active fault-tolerant control system (MAFCS) is presented with corresponding strategies,, which includes the fault diagnosis module (FDM), the dynamic library (DL) and the fault-tolerant control module (FCM). When a fault is judged from some sensor by FDM, FCM reconfigure the state of MAFCS by calling the parameters from all sub libraries in DL, in order to ensure the reliability and safety of mine hoist. The simulating result shows that, MAFCS is of certain intelligence, which can adopt the corresponding control strategies according to different fault modes, even when there are quite difference between the real data and the prior fault modes.

  18. Control of group of mobile autonomous agents via local strategies

    Institute of Scientific and Technical Information of China (English)

    Lixin GAO; Daizhan CHENG; Yiguang HONG

    2008-01-01

    This paper considers the formation control problem of multi-agent systems in a distributed fashion.Two cases of the information propagating topologies among multiple agents,characterized by graphics model,are considered.One is fixed topology.The other is switching topology which represents the limited and less reliable information exchange.The local formation control strategies established in this paper are based on a simple modification of the existing consensus control strategies.Moreover,some existing convergence conditions ale shown to be a special case of our model even in the continuous-time consensus case.Therefore.the results of this paper extend the existing results about the consensus problem.

  19. Coal surface control for advanced fine coal flotation

    Energy Technology Data Exchange (ETDEWEB)

    Fuerstenau, D.W.; Hanson, J.S.; Diao, J.; Harris, G.H.; De, A.; Sotillo, F. (California Univ., Berkeley, CA (United States)); Somasundaran, P.; Harris, C.C.; Vasudevan, T.; Liu, D.; Li, C. (Columbia Univ., New York, NY (United States)); Hu, W.; Zou, Y.; Chen, W. (Utah Univ., Salt Lake City, UT (United States)); Choudhry, V.; Shea, S.; Ghosh, A.; Sehgal, R. (Praxis Engineers, Inc., Milpitas, CA (United States))

    1992-03-01

    The initial goal of the research project was to develop methods of coal surface control in advanced froth flotation to achieve 90% pyritic sulfur rejection, while operating at Btu recoveries above 90% based on run-of-mine quality coal. Moreover, the technology is to concomitantly reduce the ash content significantly (to six percent or less) to provide a high-quality fuel to the boiler (ash removal also increases Btu content, which in turn decreases a coal's emission potential in terms of lbs SO{sub 2}/million Btu). (VC)

  20. Advanced Transport Operating System (ATOPS) control display unit software description

    Science.gov (United States)

    Slominski, Christopher J.; Parks, Mark A.; Debure, Kelly R.; Heaphy, William J.

    1992-01-01

    The software created for the Control Display Units (CDUs), used for the Advanced Transport Operating Systems (ATOPS) project, on the Transport Systems Research Vehicle (TSRV) is described. Module descriptions are presented in a standardized format which contains module purpose, calling sequence, a detailed description, and global references. The global reference section includes subroutines, functions, and common variables referenced by a particular module. The CDUs, one for the pilot and one for the copilot, are used for flight management purposes. Operations performed with the CDU affects the aircraft's guidance, navigation, and display software.

  1. NWTC Researchers Field-Test Advanced Control Turbine Systems to Increase Performance, Decrease Structural Loading of Wind Turbines and Plants

    Energy Technology Data Exchange (ETDEWEB)

    2015-08-01

    Researchers at the National Renewable Energy Laboratory's (NREL's) National Wind Technology Center (NWTC) are studying component controls, including new advanced actuators and sensors, for both conventional turbines as well as wind plants. This research will help develop innovative control strategies that reduce aerodynamic structural loads and improve performance. Structural loads can cause damage that increase maintenance costs and shorten the life of a turbine or wind plant.

  2. Study on the Fuzzy COntrol Strategy of Automobile with CVT

    Institute of Scientific and Technical Information of China (English)

    HuJianjun; QINDatong; 等

    2002-01-01

    In order to study the dynamic characteristics of automobile with a CVT system, a bond graph analysis model of continuously variable transmission is established.On the base of the simulation state space equations that are established with bond graph theory,a fuzzy control strategy with an expert system of starting process has been introduced.Considering uncertain system parameters and exterior resistance disturbing,the effect of the profile of membership function and the defuzzification algorthm on the capacity of the fuzzy controller has been studied.The result of simulation proves that the proposed fuzzy controller is effective and feasible,Such controller has been employed in the actual control and has proved practicable.The study lays a foundation for design of the fuzzy controller for automobile with a CVT system.

  3. A Computationally Efficient Aggregation Optimization Strategy of Model Predictive Control

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Model Predictive Control (MPC) is a popular technique and has been successfully used in various industrial applications. However, the big drawback of MPC involved in the formidable on-line computational effort limits its applicability to relatively slow and/or small processes with a moderate number of inputs. This paper develops an aggregation optimization strategy for MPC that can improve the computational efficiency of MPC. For the regulation problem, an input decaying aggregation optimization algorithm is presented by aggregating all the original optimized variables on control horizon with the decaying sequence in respect of the current control action.

  4. Modeling Responses of Leafy Spurge Dispersal to Control Strategies

    Institute of Scientific and Technical Information of China (English)

    Zewei Miao

    2007-01-01

    Leafy spurge (Euphorbia esula L.) has substantial negative effects on grassland biodiversity, productivity, and economic benefit in North America.To predict these negative impacts, we need an appropriate plant-spread model which can simulate the response of an invading population to different control strategies.In this study, using a stochastic map lattice approach we generated a spatially explicitly stochastic process-based model to simulate dispersal trajectories of leafy spurge under various control scenarios.The model integrated dispersal curve, propagule pressure, and population growth of leafy spurge at local and short-temporal scales to capture spread features of leafy spurge at large spatial and long-temporal scales.Our results suggested that narrow-, medium-, and fat-tailed kernels did not differ In their ability to predict spread, in contrast to previous works.For all kernels, Allee effects were significantly present and could explain the lag phase (three decades)before leafy spurge spread accelerated.When simulating from the initial stage of introduction, Allee effects were critical in predicting spread rate of leafy spurge, because the prediction could be seriously affected by the low density period of leafy spurge community.No Allee effects models were not able to simulate spread rate well in this circumstance.When applying control strategies to the current diatribution, Allee effects could stop the spread of leafy spurge; no Allee effects models, however, were able to slow but not stop the spread.The presence of Allee effects had significant ramifications on the efficiencies of control strategies.For both Allee and no Allee effects models, the later that control strategies were implemented, the more effort had to be input to achieve similar control results.

  5. Control strategies for power distribution networks with electric vehicles integration

    DEFF Research Database (Denmark)

    Hu, Junjie

    control, market based control, and price control. The thesis investigates new approaches for distribution networks congestion management. It suggests and develops a market based control for distribution grid congestion management. The general equilibrium market mechanism is utilized in the operation....... EVs can absorb energy during periods of high electricity production and feed the electricity back into the grid when the demand is high or in situations of insucient electricity generation. However, extra loads created by the increasing number of EVs may have adverse impacts on the distribution...... network such as congestion. These factors will bring new challenges to the distribution system operator. Typically, the challenges are solved by expanding the grid to t the size and the pattern of the demand. As an alternative, the capacity problem can also be solved smartly using advanced control...

  6. The push-pull strategy for citrus psyllid control.

    Science.gov (United States)

    Yan, Huaxue; Zeng, Jiwu; Zhong, Guangyan

    2015-07-01

    The Asian citrus psyllid (ACP), Diaphorina citri Kuwayama (Hemiptera: Psyllidae), is the only natural vector of Candidatus Liberibacter asiaticus that causes citrus huanglongbing (HLB), a most destructive disease of citrus. Currently, no remedial therapy exists for the disease, and so effective control of ACP is very important in curbing the transmission of the disease. The push-pull strategy should be thoroughly explored as an approach to ACP management. This mini-review summarises the current progress towards more effective repellent and attractant chemicals through investigating known repellent and attractive plants. Interactions between ACP and its host plants are also addressed, with emphasis on the possible involvement of the host biochemicals in attracting the insect. Potential ways to increase the effectiveness of the pull-push strategy are briefly discussed. It is expected that the pull-push strategy will be gradually developed following more extensive research. PMID:25256398

  7. The push-pull strategy for citrus psyllid control.

    Science.gov (United States)

    Yan, Huaxue; Zeng, Jiwu; Zhong, Guangyan

    2015-07-01

    The Asian citrus psyllid (ACP), Diaphorina citri Kuwayama (Hemiptera: Psyllidae), is the only natural vector of Candidatus Liberibacter asiaticus that causes citrus huanglongbing (HLB), a most destructive disease of citrus. Currently, no remedial therapy exists for the disease, and so effective control of ACP is very important in curbing the transmission of the disease. The push-pull strategy should be thoroughly explored as an approach to ACP management. This mini-review summarises the current progress towards more effective repellent and attractant chemicals through investigating known repellent and attractive plants. Interactions between ACP and its host plants are also addressed, with emphasis on the possible involvement of the host biochemicals in attracting the insect. Potential ways to increase the effectiveness of the pull-push strategy are briefly discussed. It is expected that the pull-push strategy will be gradually developed following more extensive research.

  8. Clear federal strategy is emerging for cost control.

    Science.gov (United States)

    O'Hara, T

    1979-02-01

    The author states that the purpose of governmental cost containment initiatives is to gain control over hospital capital expenditures, utilization, payment and quality assurance. He suggests that the costs of hospital operation should be completely re-examined stating that the reform of the hospital payment system is emerging as the energizing factor which will stimulate proper allocation of capital resources and effective utilization and quality assurance. O'Hare outlines the potential of the federal strategy. Recent legislation (PL 93-641 and PL 95-142) has mandated that hospital financial and statistical data be made available to federal agencies. He concludes that a dominant federal role in cost containment strategy threatens to abolish individual differences between institutions and their ability to be responsive to local needs. The author urges hospital leadership to take a more active position in implementing a cost containment strategy.

  9. Research and development on the application of advanced control technologies to advanced nuclear reactor systems: A US national perspective

    International Nuclear Information System (INIS)

    Control system designs for nuclear power plants are becoming more advanced through the use of digital technology and automation. This evolution is taking place because of: (1) the limitations in analog based control system performance and maintenance and availability and (2) the promise of significant improvement in plant operation and availability due to advances in digital and other control technologies. Digital retrofits of control systems in US nuclear plants are occurring now. Designs of control and protection systems for advanced LWRs are based on digital technology. The use of small inexpensive, fast, large-capacity computers in these designs is the first step of an evolutionary process described in this paper. Under the sponsorship of the US Department of Energy (DOE), Oak Ridge National Laboratory, Argonne National Laboratory, GE Nuclear Energy and several universities are performing research and development in the application of advances in control theory, software engineering, advanced computer architectures, artificial intelligence, and man-machine interface analysis to control system design. The target plant concept for the work described in this paper is the Power Reactor Inherently Safe Module reactor (PRISM), an advanced modular liquid metal reactor concept. This and other reactor designs which provide strong passive responses to operational upsets or accidents afford good opportunities to apply these advances in control technology. 18 refs., 5 figs

  10. Advanced dc motor controller for battery-powered electric vehicles

    Science.gov (United States)

    Belsterling, C. A.

    1981-01-01

    A motor generation set is connected to run from the dc source and generate a voltage in the traction motor armature circuit that normally opposes the source voltage. The functional feasibility of the concept is demonstrated with tests on a Proof of Principle System. An analog computer simulation is developed, validated with the results of the tests, applied to predict the performance of a full scale Functional Model dc Controller. The results indicate high efficiencies over wide operating ranges and exceptional recovery of regenerated energy. The new machine integrates both motor and generator on a single two bearing shaft. The control strategy produces a controlled bidirectional plus or minus 48 volts dc output from the generator permitting full control of a 96 volt dc traction motor from a 48 volt battery, was designed to control a 20 hp traction motor. The controller weighs 63.5 kg (140 lb.) and has a peak efficiency of 90% in random driving modes and 96% during the SAE J 227a/D driving cycle.

  11. Dynamic Modeling, Optimization, and Advanced Control for Large Scale Biorefineries

    DEFF Research Database (Denmark)

    Prunescu, Remus Mihail

    of the L1 adaptive output feedback controller [10] are developed: one for biomass pretreatment temperature [11] and another one for pH in enzymatic hydrolysis [12]. Biomass conversion is highly sensitive to these process parameters, which exhibit nonlinear behavior and can change nominal values...... years PhD project that was run by Technical University of Denmark (DTU) in collaboration with the largest Danish energy company DONG Energy A/S between 2012 and 2015. The company owns a demonstration scale second generation biorefinery in Kalundborg, Denmark, also known as the Inbicon demonstration...... plant [3]. The goal of the project is to utilize realtime data extracted from the large scale facility to formulate and validate first principle dynamic models of the plant. These models are then further exploited to derive model-based tools for process optimization, advanced control and real...

  12. A new weed control strategy in onion culture.

    Science.gov (United States)

    Thieron, M; Kerres, W; Schäffer, A

    2007-01-01

    A new strategy combining modem hoeing technique and spray application has been developed in order to reduce the amount of herbicides down to 20% compared to common practice. The effects on weed control have been investigated as well as the impact on qualitative and quantitative harvest. In two large scale field trials and two years of testing the authors evaluated different hoeing techniques combined with band spray application and standard spray application, the minimal lethal herbicide dose method (MLHD). All varieties have been calculated for environmental impact as well as practical and economical means. These studies reveal crop losses due to improper weed control as well as losses due to herbicide stress. Detailed information on concentration depending impact of several herbicides have been correlated to their control of different weeds and the achieved yield. Two contrary effects influencing the total yield have been identified. The novel strategy is based on the knowledge of these complex effects which finally led to a well practicable and highly economic strategy that enables onion farmers to control weeds while reducing the amounts of herbicides down to approximately 20%. PMID:18399447

  13. Advanced methods of quality control in nuclear fuel fabrication

    International Nuclear Information System (INIS)

    Under pressure of current economic and electricity market situation utilities implement more demanding fuel utilization schemes including higher burn ups and thermal rates, longer fuel cycles and usage of Mo fuel. Therefore, fuel vendors have recently initiated new R and D programmes aimed at improving fuel quality, design and materials to produce robust and reliable fuel. In the beginning of commercial fuel fabrication, emphasis was given to advancements in Quality Control/Quality Assurance related mainly to product itself. During recent years, emphasis was transferred to improvements in process control and to implementation of overall Total Quality Management (TQM) programmes. In the area of fuel quality control, statistical control methods are now widely implemented replacing 100% inspection. This evolution, some practical examples and IAEA activities are described in the paper. The paper presents major findings of the latest IAEA Technical Meetings (TMs) and training courses in the area with emphasis on information received at the TM and training course held in 1999 and other latest publications to provide an overview of new developments in process/quality control, their implementation and results obtained including new approaches to QC

  14. Optimal management strategies in variable environments: Stochastic optimal control methods

    Science.gov (United States)

    Williams, B.K.

    1985-01-01

    Dynamic optimization was used to investigate the optimal defoliation of salt desert shrubs in north-western Utah. Management was formulated in the context of optimal stochastic control theory, with objective functions composed of discounted or time-averaged biomass yields. Climatic variability and community patterns of salt desert shrublands make the application of stochastic optimal control both feasible and necessary. A primary production model was used to simulate shrub responses and harvest yields under a variety of climatic regimes and defoliation patterns. The simulation results then were used in an optimization model to determine optimal defoliation strategies. The latter model encodes an algorithm for finite state, finite action, infinite discrete time horizon Markov decision processes. Three questions were addressed: (i) What effect do changes in weather patterns have on optimal management strategies? (ii) What effect does the discounting of future returns have? (iii) How do the optimal strategies perform relative to certain fixed defoliation strategies? An analysis was performed for the three shrub species, winterfat (Ceratoides lanata), shadscale (Atriplex confertifolia) and big sagebrush (Artemisia tridentata). In general, the results indicate substantial differences among species in optimal control strategies, which are associated with differences in physiological and morphological characteristics. Optimal policies for big sagebrush varied less with variation in climate, reserve levels and discount rates than did either shadscale or winterfat. This was attributed primarily to the overwintering of photosynthetically active tissue and to metabolic activity early in the growing season. Optimal defoliation of shadscale and winterfat generally was more responsive to differences in plant vigor and climate, reflecting the sensitivity of these species to utilization and replenishment of carbohydrate reserves. Similarities could be seen in the influence of both

  15. Design and Advanced Control of Switched Reluctance Motors

    DEFF Research Database (Denmark)

    Rasmussen, Peter Omand

    with SR technology is the reputation of the high acoustic noise emission compared to other electrical machines. Therefore, extra focus to analyze this specific subject is done. The major origin to the high level of acoustic noise is due to highly concentrated normal forces with a high harmonic content...... with the control strategy and the output is the sound pressure at the top of the stator yoke. This is presented as both a technical A-weighted value and as a subjective value in form of the sound from the PC having the SRDaS program installed. The developed acoustic models are also verified in practice on several...

  16. Intelligent Control Strategy of Fuel Cell Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    Abolfazl Hajizadeh

    2011-05-01

    Full Text Available This paper deals a control strategy developed for optimizing the power flow in a Fuel Cell Hybrid Vehicle (FCHV structure. This method implements an on-line power management based on the neuro-fuzzy controller between dual power sources that consist of a battery bank and a fuel cell (FC. This structure included battery and fuel cell and its power train system include an Electric Motor (EM and vehicle dynamics. The proposed control method involves an intelligent controller which captures all of possible operation modes and predicts the driver intention. Moreover, there are local controllers to regulate the set points of each subsystems to reach the best performance and acceptable operation indexes. Simulation results of hybrid system illustrate improvement in the operation efficiency of the FCHV and the battery state of charge and fuel cell utilization factor have been maintained at a reasonable level.

  17. A Composite Model Predictive Control Strategy for Furnaces

    Institute of Scientific and Technical Information of China (English)

    Hao Zang; Hongguang Li; Jingwen Huang; Jia Wang

    2014-01-01

    Tube furnaces are essential and primary energy intensive facilities in petrochemical plants. Operational optimi-zation of furnaces could not only help to improve product quality but also benefit to reduce energy consumption and exhaust emission. Inspired by this idea, this paper presents a composite model predictive control (CMPC) strategy, which, taking advantage of distributed model predictive control architectures, combines tracking nonlinear model predictive control and economic nonlinear model predictive control metrics to keep process running smoothly and optimize operational conditions. The control ers connected with two kinds of communi-cation networks are easy to organize and maintain, and stable to process interferences. A fast solution algorithm combining interior point solvers and Newton's method is accommodated to the CMPC realization, with reason-able CPU computing time and suitable online applications. Simulation for industrial case demonstrates that the proposed approach can ensure stable operations of furnaces, improve heat efficiency, and reduce the emission effectively.

  18. Selecting alternative strategies for community health education in guineaworm control.

    Science.gov (United States)

    Brieger, W R; Ramakrishna, J; Akpovi, S U; Adeniyi, J D

    1984-01-01

    Community health education strategies in guineaworm control can be applied at several intervention levels. Community development mobilizes local resources to provide safe water supplies such as wells. Mass education in schools and communities can teach personal protection measures such as filtering water. Training of volunteer community health workers produces front line staff, who by being culturally in tune with the community can demonstrate and promote the use of appropriate prevention and treatment measures. Advocacy assists community members to express their needs to government and ministry decision makers. All of these strategies have been applied in a community health education/primary health care program in Idere, Ibarapa District, Oyo State. Community development for well construction was found to be a long-term strategy that first must overcome problems of village organization and resource location. Mass education, to be effective, must have a simple and acceptable technology to promote. Trained village health workers must overcome traditional beliefs that inhibit use of preventive and treatment measures. Advocacy requires basic political education of community leaders. A variety of health education strategies is needed to address short- and long-term priorities as well as to overcome the different barriers to guineaworm control. PMID:20841266

  19. Recent advances in microbial production of fuels and chemicals using tools and strategies of systems metabolic engineering

    DEFF Research Database (Denmark)

    Cho, Changhee; Choi, So Young; Luo, Zi Wei;

    2015-01-01

    The advent of various systems metabolic engineering tools and strategies has enabled more sophisticated engineering of microorganisms for the production of industrially useful fuels and chemicals. Advances in systems metabolic engineering have been made in overproducing natural chemicals and prod...

  20. Comparison of different control strategies on FMD in Denmark

    DEFF Research Database (Denmark)

    Boklund, Anette; Hisham Beshara Halasa, Tariq; Christiansen, Lasse Engbo;

    2012-01-01

    The purpose of this study was to compare different control strategies that could be used in Denmark during an outbreak of FMD, based on epidemiological, ethical and economic parameters. Nearly a hundred different control strategies and more than 30 sensitivity analyses were run, changing between...... depopulation (Depop), suppressive (VacToKill) and protective (VacToLive) vaccination with different times for implementation and different zone sizes. It is therefore obvious that not all results can be included here; neither will all results be presented at the seminar. However, we have done our best...... of the epidemics, it is shown that vaccination is more expensive compared to depopulation. Results from 1000 epidemics starting in cattle herds in cattle dense areas. Epidemiological results from ISP presented as medians and 5-95 percentiles (brackets), economical as means. The size, duration and costs...

  1. Comparison of Power Control Strategies for DFIG Wind Turbines

    DEFF Research Database (Denmark)

    Teodorescu, Remus; Luna, A.; Rodríguez, P.;

    2008-01-01

    The classical control techniques for regulating the active and reactive power delivery in doubly fed induction generators (DFIG), for wind power applications, are normally based on voltage oriented control (VOC) strategies. Among these algorithms, those that work in a synchronous reference frame......, attached to the magnetic flux vector, became very popular. In spite of the good behaviour of such algorithms their performance depends highly on an accurate detection of the stator flux position, something that can be critical under unbalanced or distorted grid voltage conditions. This paper presents a new...... with the response obtained with a classical VOC algorithm by means of PSCAD/EMTDC® simulation models. Finally the behaviour of both strategies will be tested in a real setup....

  2. MERCURY CONTROL WITH THE ADVANCED HYBRID PARTICULATE COLLECTOR

    Energy Technology Data Exchange (ETDEWEB)

    Ye Zhuang; Stanley J. Miller; Grant E. Dunham; Michelle R. Olderbak

    2002-02-01

    Since 1995, DOE has supported development of a new concept in particulate control, called the advanced hybrid particulate collector (AHPC). The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The AHPC provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emission with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The AHPC appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas-solid contactor. The objective of the three-task project is to demonstrate 90% total mercury control in the AHPC at a lower cost than current mercury control estimates. The approach includes bench-scale batch testing that ties the new work to previous results and links results with larger-scale pilot testing with real flue gas on a coal-fired combustion system, pilot-scale testing on a coal-fired combustion system with both a pulse-jet baghouse and an AHPC to prove or disprove the research hypotheses, and field demonstration pilot-scale testing at a utility power plant to prove scaleup and demonstrate longer-term mercury control. This project, if successful, will demonstrate at the pilot-scale level a technology that would provide a cost-effective technique to accomplish control of mercury emissions and, at the same time, greatly enhance fine particulate collection efficiency. The technology can be used to retrofit systems currently employing inefficient ESP technology as well as for new construction, thereby providing a solution to a large segment of the U.S. utility industry as well as other industries requiring mercury control.

  3. Speed-sensorless control strategy for multi-phase induction generator in wind energy conversion systems

    Directory of Open Access Journals (Sweden)

    Dumnić Boris P.

    2016-01-01

    Full Text Available Renewable energy sources, especially wind energy conversion systems (WECS, exhibit constant growth. Increase in power and installed capacity led to advances in WECS topologies. Multi-phase approach presents a new development direction, with several key advantages over three-phase systems. Paired with a sensorless control strategy, multi-phase machines are expected to take primacy over standard solutions. This paper presents speed sensorless vector control of an asymmetrical six-phase induction generator based on a model reference adaptive system (MRAS. Suggested topology and developed control algorithm show that sensorless control can yield appropriate dynamic characteristics for the use in WECS with increase in reliability and robustness. [Projekat Ministarstva nauke Republike Srbije, br. III 042004: Smart Electricity Distribution Grids Based on Distribution Management System and Distributed Generation

  4. Neoadjuvant therapy for locally advanced melanoma: new strategies with targeted therapies.

    Science.gov (United States)

    La Greca, Michele; Grasso, Giuseppe; Antonelli, Giovanna; Russo, Alessia Erika; Bartolotta, Salvatore; D'Angelo, Alessandro; Vitale, Felice Vito; Ferraù, Francesco

    2014-01-01

    Neoadjuvant chemotherapy has been successfully tested in several bulky solid tumors, but it has not been utilized in advanced cutaneous melanoma, primarily because effective medical treatments for this disease have been lacking. However, with the development of new immunotherapies (monoclonal antibodies specific for cytotoxic T lymphocyte-associated antigen 4 [anti-CTLA-4] and programmed death protein-1 [anti-PD1]) and small molecules interfering with intracellular pathways (anti-BRAF and mitogen-activated protein kinase kinase [anti- MEK]) the use of this approach is becoming a viable treatment strategy for locally advanced melanoma. The neoadjuvant setting provides a double opportunity for a better knowledge of these drugs: a short-term evaluation of their intrinsic activity, and a deeper analysis of their action and resistance-induction mechanisms. BRAF inhibitors seem to be ideal candidates for the neoadjuvant setting, because of their prompt, repeatedly confirmed response in V600E BRAF-mutant metastatic melanoma. In this report we summarize studies focused on the neoadjuvant use of traditional medical treatments in advanced melanoma and anecdotal cases of this approach with the use of biologic therapies. Moreover, we discuss our experience with neoadjuvant targeted therapy as a priming for radical surgery in a patient with BRAF V600E mutation-positive advanced melanoma.

  5. Congestion Control Strategy for Opportunistic Network Based on Message Values

    OpenAIRE

    Deng-yin Zhang; Min Yang; Lei Cui

    2014-01-01

    To solve the congestion problem in opportunistic networks, a congestion control strategy based on message deleting and transferring(DATM) is proposed. The congested node calculates the storage value of each message according to the forwarding probability and TTL of message, then deletes the message with the minimum storage value and transfers the message with the minimum forwarding probability to neighboring nodes. The neighboring nodes calculate the receiving value of the message according t...

  6. Model Predictive Control Strategy to Forecast Employability in Earth Sciences

    OpenAIRE

    Courtial, E; Garrouste, C

    2014-01-01

    International audience Energy prices and environmental policies influence more than ever employment trends across the world. The purpose of this paper is to develop a control strategy to enhance the employability of French graduates in a field that is both a key driver and a significant target of these new trends, namely Earth Sciences. The aim is to provide French universities with a predictive tool to adjust efficiently their skills' supply capacity with the demand forecasts at the Europ...

  7. Analysis of Control Strategies for Diode Clamped Multilevel Inverter

    OpenAIRE

    C. R. Balamurugan; S. P. NATARAJAN; R. Revathy

    2013-01-01

    This paper presents the comparison of various Pulse Width Modulation (PWM) strategies for the three phase Diode Clamped Multi Level Inverter (DCMLI). The main contribution of this paper is the proposal of new modulation schemes with Variable Amplitude (VA) and various new schemes adopting the constant switching frequency and also variable switching frequency multicarrier control freedom degree combination concepts are developed and simulated for the chosen three phase DCMLI. The three phase D...

  8. Recent advances in proteolysis and peptide/protein separation by chromatographic strategies

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    This review gives a broad glance on the progress of recent advances on proteolysis and peptide/protein separation by chroma-tographic strategies in the past ten years, covering the main research in these areas especially in China. The reviewed research focused on enzymatic micro-reactors and peptide separation in bottom-up approaches, and protein and peptide separation in top-down approaches. The new enzymatic micro-reactor is able to accelerate proteolytic reaction rate from conventionally a couple of hours to a few seconds, and the multiple dimensional chromatographic-separation with various models or arrays could sufficiently separate the proteomic mixture. These advances have significantly promoted the research of protein/peptide separation and identification in proteomics.

  9. A modern control room for Indian Advanced Heavy Water Reactor

    International Nuclear Information System (INIS)

    Advanced Heavy Water Reactor (AHWR) is a next generation nuclear power plant being developed by Bhabha Atomic Research Centre, India. AHWR is a vertical, pressure tube type, heavy-water-moderated, boiling light-water-cooled, innovative reactor, relying on natural circulation for core cooling in all operating and accident conditions. In addition, it incorporates various passive systems for decay heat removal, containment cooling and isolation. In addition to the many passive safety features, AHWR has state of the art I and C architecture based on extensive use of computers and networking. In tune with the many advanced features of the reactor, a centralized modern control room has been conceived for operation and monitoring of the plant. The I and C architecture enables the implementation of a fully computerised operator friendly control room with soft Human Machine Interfaces (HMI). While doing so, safety has been given due consideration. The control and monitoring of AHWR systems are carried out from the fully computer-based operator interfaces, except safety systems, for which only monitoring is provided from soft HMI. The control of the safety systems is performed from dedicated hardwired safety system panels. Soft HMI reduces the number of individual control devices and improves their reliability. The paper briefly describes the I and C architecture adopted for the AHWR plant along with the interfaces to the main and backup control rooms. There are many issues involved while introducing soft HMI based operator interfaces for Nuclear Power Plants (NPP) compared to the conventional plants. Besides discussing the implementation issues, the paper elaborates the design considerations that have undergone in the design of various components in the main control room especially operator workstations, shift supervisor console, safety system panels and large display panels. Mainly task based displays have been adopted for the routine operator interactions of the plant

  10. Expanding Robust HCCI Operation with Advanced Valve and Fuel Control Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Szybist, J. P. [Oak Ridge National Lab., Oak Ridge, TN (United States); Confer, K. [Delphi Automotive Systems (United States)

    2012-09-11

    Delphi Automotive Systems and ORNL established this CRADA to advance the commercialization potential of the homogeneous charge compression ignition (HCCI) advanced combustion strategy for gasoline engine platforms. HCCI combustion has been shown by others to produce high diesel-like efficiency on a gasoline engine platform while simultaneously producing low NOX and particulate matter emissions. However, the commercialization barriers that face HCCI combustion are significant, with requirements for a more active engine control system, likely with next-cycle closed-loop feedback control, and with advanced valve train technologies to enable negative valve overlap conditions. In the partnership between Delphi and ORNL, each organization brought a unique and complementary set of skills to the project. Delphi has made a number of breakthroughs with production-intent valve train technologies and controls in recent years to make a part time production-intent HCCI engine plausible. ORNL has extensive knowledge and expertise with HCCI combustion, and also has a versatile research engine with hydraulic valve actuation (HVA) that is useful for guiding production of a cam-based HCCI system. Partnering these knowledge bases and capabilities was essential towards making progress to better understand HCCI combustion and the commercialization barriers that it faces. ORNL and Delphi maintained strong collaboration throughout the project. Meetings were held regularly, with additional reports, presentations, and meetings as necessary to maintain progress. Delphi provided guidance to ORNL regarding operational strategies to investigate on their single-cylinder research engine with HVA and data from their experimental multi-cylinder engine for modeling. ORNL provided single-cylinder engine data and modeling results.

  11. AMBA Based Advanced DMA Controller for SoC

    Directory of Open Access Journals (Sweden)

    Abdullah Aljumah

    2016-03-01

    Full Text Available this paper describes the implementation of an AMBA Based Advanced DMA Controller for SoC. It uses AMBA Specifications, where two buses AHB and APB are defined and works for processor as system bus and peripheral bus respectively. The DMA controller functions between these two buses as a bridge and allow them to work concurrently. Depending on the speed of peripherals it uses buffering mechanism. Therefore an asynchronous FIFO is used for synchronizing the speed of peripherals. The proposed DMA controller can works in SoC along with processor and achieve fast data rate. The method introduced significant volume of data transfer with very low timing characteristics. Thus it is a better choice in respect of timing and volume of data. These two issues have been resolved under this research study. The results are compared with the AMD processors, like Geode GX 466, GX 500 and GX 533, and the presence and absence of DMA controller with processor is discussed and compared. The DMAC stands to be better alternative in SoC design.

  12. Trajectory control strategy of cathodes in blisk electrochemical machining

    Institute of Scientific and Technical Information of China (English)

    Zhu Dong; Zhu Di; Xu Zhengyang; Zhou Laishui

    2013-01-01

    A turbine blisk,which combines blades and a disk together,is one of the most important components of an aero engine.In the process of blisk electrochemical machining (ECM),the sheet cathode,which is usually used as a tool electrode,has a complicated structure.In addition to that,the channel between the adjacent blades is narrow and twisted,so interference is apt to happen when the sheet cathode feeds into the channel.Therefore,it is important to choose suitable trajectory control strategy.In this paper,a new trajectory control strategy of the sheet cathode is presented and corresponding simulation analysis is conducted on the basis of an actual blisk model.The simulation results demonstrate that the sheet cathode can feed into the channel by a spatial line trajectory without interference.Moreover,the verification experiments are carried out according to the simulation.The experimental results show that the cathode can move into the channel without interference.It is verified that the new trajectory control strategy is correct and can be used in the blisk ECM process successfully.

  13. Benchmarking of Control Strategies for Wastewater Treatment Plants

    DEFF Research Database (Denmark)

    Wastewater treatment plants are large non-linear systems subject to large perturbations in wastewater flow rate, load and composition. Nevertheless these plants have to be operated continuously, meeting stricter and stricter regulations. Many control strategies have been proposed in the literature...... for improved and more efficient operation of wastewater treatment plants. Unfortunately, their evaluation and comparison – either practical or based on simulation – is difficult. This is partly due to the variability of the influent, to the complexity of the biological and biochemical phenomena......, plant layout, controllers, sensors, performance criteria and test procedures, i.e. a complete benchmarking protocol....

  14. Control Strategies for DFIG Wind Turbines Under Grid Fault

    DEFF Research Database (Denmark)

    Luna, Alvara; Rolan, A.; Medeiros, G.;

    2009-01-01

    The classical control techniques for regulating the active and reactive power delivery in doubly fed induction generators (DFIG), for wind power applications, are normally based on voltage oriented control (VOC) strategies. Among these algorithms, those that work in a synchronous reference frame......, attached to the magnetic flux vector, became very popular. In spite of the good behaviour of such algorithms their performance depends highly on an accurate detection of the stator flux position, something that can be critical under unbalanced or distorted grid voltage conditions. This paper presents a new...... with the response obtained with a classical VOC algorithm by means of PSCAD/EMTDC® simulation models....

  15. Advanced nuclear power systems: Design, technology, safety and strategies for their deployment

    International Nuclear Information System (INIS)

    The objectives of the symposium were to provide high level decision makers with an overview of the discussion concerning the need for nuclear power and salient features of advanced nuclear power systems; a forum for discussing the design objectives and safety approaches for such systems and the views of regulatory bodies; a forum for identifying barriers to the deployment of these systems and for reviewing strategies to overcome these barriers; and a forum for reviewing options for international cooperation in the development and deployment of such systems. Refs, figs and tabs

  16. Advanced strategies for end-stage heart failure: combining regenerative approaches with LVAD, a new horizon?

    Directory of Open Access Journals (Sweden)

    Cheyenne eTseng

    2015-04-01

    Full Text Available Despite the improved treatment of cardiovascular diseases the population with end-stage heart failure is progressively growing. The scarcity of the gold standard therapy, heart transplantation, demands novel therapeutic approaches. For patients awaiting transplantation ventricular assist devices have been of great benefit on survival. To allow explantation of the assist device and obviate heart transplantation, sufficient and durable myocardial recovery is necessary. However, explant rates so far are low. Combining mechanical circulatory support with regenerative therapies such as cell(-based therapy and biomaterials might give rise to improved long-term results. Although synergistic effects are suggested with mechanical support and stem cell therapy, evidence in both preclinical and clinical setting is lacking. This review focuses on advanced and innovative strategies for the treatment of end-stage heart failure and furthermore appraises clinical experience with combined strategies.

  17. Control Systems Cyber Security: Defense-in-Depth Strategies

    Energy Technology Data Exchange (ETDEWEB)

    Mark Fabro

    2007-10-01

    Information infrastructures across many public and private domains share several common attributes regarding IT deployments and data communications. This is particularly true in the control systems domain. A majority of the systems use robust architectures to enhance business and reduce costs by increasing the integration of external, business, and control system networks. However, multi-network integration strategies often lead to vulnerabilities that greatly reduce the security of an organization, and can expose mission-critical control systems to cyber threats. This document provides guidance and direction for developing ‘defense-in-depth’ strategies for organizations that use control system networks while maintaining a multi-tier information architecture that requires: • Maintenance of various field devices, telemetry collection, and/or industrial-level process systems • Access to facilities via remote data link or modem • Public facing services for customer or corporate operations • A robust business environment that requires connections among the control system domain, the external Internet, and other peer organizations.

  18. Designing new strategy for controlling DNA orientation in biosensors.

    Science.gov (United States)

    Feng, Chao; Ding, Hong-ming; Ren, Chun-lai; Ma, Yu-qiang

    2015-01-01

    Orientation controllable DNA biosensors hold great application potentials in recognizing small molecules and detecting DNA hybridization. Though electric field is usually used to control the orientation of DNA molecules, it is also of great importance and significance to seek for other triggered methods to control the DNA orientation. Here, we design a new strategy for controlling DNA orientation in biosensors. The main idea is to copolymerize DNA molecules with responsive polymers that can show swelling/deswelling transitions due to the change of external stimuli, and then graft the copolymers onto an uncharged substrate. In order to highlight the responsive characteristic, we take thermo-responsive polymers as an example, and reveal multi-responsive behavior and the underlying molecular mechanism of the DNA orientation by combining dissipative particle dynamics simulation and molecular theory. Since swelling/deswelling transitions can be also realized by using other stimuli-responsive (like pH and light) polymers, the present strategy is universal, which can enrich the methods of controlling DNA orientation and may assist with the design of the next generation of biosensors. PMID:26400770

  19. CONTROL STRATEGY FOR ASSURING CONSTANT SURFACE FINISH BY CONTROLLING CUTTING FORCES

    OpenAIRE

    Čuš, Franci; Župerl, Uroš

    2013-01-01

    The objective of this paper is to present surface roughness control strategy aimed at controlling the cutting force and maintaining constant roughness of the surface being milled by digital adaptation of cutting parameters. The idea of this control structure is to merge the off-line cutting condition optimization and genetic programming (GP) model based surface roughness control. The off-line optimization integrates the neural network (NN) modelling of the objective function and particle swar...

  20. Economic analysis of HPAI control in the Netherlands II: comparison of control strategies.

    Science.gov (United States)

    Longworth, N; Mourits, M C M; Saatkamp, H W

    2014-06-01

    A combined epidemiological-economic modelling approach was used to analyse strategies for highly pathogenic avian influenza (HPAI) control for the Netherlands. The modelling framework used was InterSpread Plus (ISP), a spatially based, stochastic and dynamic simulation model. A total of eight control strategies were analysed, including pre-emptive depopulation and vaccination strategies. The analysis was carried out for three different regions in the Netherlands: high-, medium- and low-density areas (HDA, MDA and LDA, respectively). The analysis included the veterinary impact (e.g. number of infected premises and duration), but was particularly focused on the impact on direct costs (DC) and direct consequential costs. The efficient set of control strategies for HDA and MDA included strategies based on either pre-emptive depopulation only or combined vaccination and pre-emptive depopulation: D2 (pre-emptive depopulation within a radius of 2 km), RV3 + D1 (ring vaccination within a radius of 3 km and additional pre-emptive depopulation within a radius of 1 km) and PV + D1 (preventive vaccination in non-affected HDAs and pre-emptive depopulation within a radius of 1 km in the affected HDA). Although control solely based on depopulation in most cases showed to be effective for LDA, pre-emptive depopulation showed to have an additional advantage in these areas, that is, prevention of 'virus jumps' to other areas. The pros and cons of the efficient control strategies were discussed, for example, public perception and risk of export restrictions. It was concluded that for the Netherlands control of HPAI preferably should be carried out using strategies including pre-emptive depopulation with or without vaccination. Particularly, the short- and long-term implications on export, that is, indirect consequential costs (ICC) and aftermath costs of these strategies, should be analysed further.

  1. Integrated Control Strategies Supporting Autonomous Functionalities in Mobile Robots

    Directory of Open Access Journals (Sweden)

    Brandon Sights

    2006-10-01

    Full Text Available High-level intelligence allows a mobile robot to create and interpret complex world models, but without a precise control system, the accuracy of the world model and the robot's ability to interact with its surroundings are greatly diminished. This problem is amplified when the environment is hostile, such as in a battlefield situation where an error in movement or a slow response may lead to destruction of the robot. As the presence of robots on the battlefield continues to escalate and the trend toward relieving the human of the low-level control burden advances, the ability to combine the functionalities of several critical control systems on a single platform becomes imperative.

  2. Neoadjuvant therapy for locally advanced melanoma: new strategies with targeted therapies

    Directory of Open Access Journals (Sweden)

    La Greca M

    2014-06-01

    Full Text Available Michele La Greca,1 Giuseppe Grasso,2 Giovanna Antonelli,1 Alessia Erika Russo,1 Salvatore Bartolotta,3 Alessandro D’Angelo,1 Felice Vito Vitale,1 Francesco Ferraù1 1Medical Oncology Department, San Vincenzo Hospital, Taormina, Messina, Italy; 2Pathology Department, San Vincenzo Hospital, Taormina, Messina, Italy; 3Surgical Unit, Casa di Cura Gretter-Lucina, Catania, Catania, Italy Abstract: Neoadjuvant chemotherapy has been successfully tested in several bulky solid tumors, but it has not been utilized in advanced cutaneous melanoma, primarily because effective medical treatments for this disease have been lacking. However, with the development of new immunotherapies (monoclonal antibodies specific for cytotoxic T lymphocyte-associated antigen 4 [anti-CTLA-4] and programmed death protein-1 [anti-PD1] and small molecules interfering with intracellular pathways (anti-BRAF and mitogen-activated protein kinase kinase [anti- MEK] the use of this approach is becoming a viable treatment strategy for locally advanced melanoma. The neoadjuvant setting provides a double opportunity for a better knowledge of these drugs: a short-term evaluation of their intrinsic activity, and a deeper analysis of their action and resistance-induction mechanisms. BRAF inhibitors seem to be ideal candidates for the neoadjuvant setting, because of their prompt, repeatedly confirmed response in V600E BRAF-mutant metastatic melanoma. In this report we summarize studies focused on the neoadjuvant use of traditional medical treatments in advanced melanoma and anecdotal cases of this approach with the use of biologic therapies. Moreover, we discuss our experience with neoadjuvant targeted therapy as a priming for radical surgery in a patient with BRAF V600E mutation-positive advanced melanoma. Keywords: neoadjuvant setting, biologic, targeted therapy, vemurafenib, advanced melanoma

  3. Advanced methods of microscope control using μManager software

    Directory of Open Access Journals (Sweden)

    Arthur D Edelstein

    2014-07-01

    Full Text Available µManager is an open-source, cross-platform desktop application, to control a wide variety of motorized microscopes, scientific cameras, stages, illuminators, and other microscope accessories. Since its inception in 2005, µManager has grown to support a wide range of microscopy hardware and is now used by thousands of researchers around the world. The application provides a mature graphical user interface and offers open programming interfaces to facilitate plugins and scripts. Here, we present a guide to using some of the recently added advanced µManager features, including hardware synchronization, simultaneous use of multiple cameras, projection of patterned light onto a specimen, live slide mapping, imaging with multi-well plates, particle localization and tracking, and high-speed imaging.

  4. International conference on Advances in Intelligent Control and Innovative Computing

    CERN Document Server

    Castillo, Oscar; Huang, Xu; Intelligent Control and Innovative Computing

    2012-01-01

    In the lightning-fast world of intelligent control and cutting-edge computing, it is vitally important to stay abreast of developments that seem to follow each other without pause. This publication features the very latest and some of the very best current research in the field, with 32 revised and extended research articles written by prominent researchers in the field. Culled from contributions to the key 2011 conference Advances in Intelligent Control and Innovative Computing, held in Hong Kong, the articles deal with a wealth of relevant topics, from the most recent work in artificial intelligence and decision-supporting systems, to automated planning, modelling and simulation, signal processing, and industrial applications. Not only does this work communicate the current state of the art in intelligent control and innovative computing, it is also an illuminating guide to up-to-date topics for researchers and graduate students in the field. The quality of the contents is absolutely assured by the high pro...

  5. GPS based Advanced Vehicle Tracking and Vehicle Control System

    Directory of Open Access Journals (Sweden)

    Mashood Mukhtar

    2015-02-01

    Full Text Available Security systems and navigators have always been a necessity of human‟s life. The developments of advanced electronics have brought revolutionary changes in these fields. In this paper, we will present a vehicle tracking system that employs a GPS module and a GSM modem to find the location of a vehicle and offers a range of control features. To complete the design successfully, a GPS unit, two relays, a GSM Modem and two MCU units are used. There are five features introduced in the project. The aim of this project is to remotely track a vehicle‟s location, remotely switch ON and OFF the vehicle‟s ignition system and remotely lock and unlock the doors of the vehicle. An SMS message is sent to the tracking system and the system responds to the users request by performing appropriate actions. Short text messages are assigned to each of these features. A webpage is specifically designed to view the vehicle‟s location on Google maps. By using relay based control concept introduced in this paper, number of control features such as turning heater on/off, radio on/off etc. can be implemented in the same fashion.

  6. Strategies for controlling residential combined cooling, heating and power systems

    Energy Technology Data Exchange (ETDEWEB)

    Ferguson, A. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy Technology Centre

    2004-07-01

    Residential cogeneration technologies are considered to be excellent candidates for combined cooling, heating and power (CCHP) technology. The characteristics of CCHP technology were outlined in this paper along with control strategies required for meeting concurrent cooling, heating and electrical loads. The integration of these control strategies into a CCHP system controller model was also discussed. In particular, a model of a thermally-activated cooling (TAC) unit was developed at the CANMET Energy Technology Centre. The model was integrated into the ESP-r/HOT3000 residential simulation modelling tool. The TAC unit model was then combined with a previously developed fuel cell model in a residential HVAC network. The study showed that if a cogeneration system was coupled to a TAC unit such as an absorption chiller, any surplus heat could be exploited during the summer months to deliver useful cooling to the building using CCHP technology. The modelling results suggest that a CCHP controller can be compatible with improved, dynamic fuel-cells models. Future work will focus on including electrical storage systems and on-site renewable technologies such as photovoltaic panels. 6 refs., 2 tabs., 8 figs.

  7. A Paratransgenic Strategy for the Control of Chagas Disease

    Directory of Open Access Journals (Sweden)

    Ivy Hurwitz

    2012-01-01

    Full Text Available Chagas disease results from infection with the parasite Trypanosoma cruzi. This disease remains a significant cause of morbidity and mortality in central and south America. Chagas disease now exists and is detected worldwide because of human migration. Control of Chagas disease has relied mainly on vector eradication however, the development of insect resistance to pesticides, coupled with cost and adverse health effects of insecticide treatments, has prompted our group to investigate novel methods of transmission control. Our laboratory has been instrumental in the development of the paratransgenic strategy to control vectorial transmission of T. cruzi. In this paper, we discuss various components of the paratransgenic approach. Specifically, we describe classes of molecules that can serve as effectors, including antimicrobial peptides, endoglucanases, and highly specific single chain antibodies that target surface glycoprotein tags on the surface of T. cruzi. Furthermore, we address evolving concepts related to field dispersal of engineered bacteria as part of the paratransgenic control strategy and attendant risk assessment evaluation.

  8. Tuberculosis 2015: Burden, Challenges and Strategy for Control and Elimination.

    Science.gov (United States)

    Raviglione, Mario; Sulis, Giorgia

    2016-06-24

    Tuberculosis (TB) is a leading cause of morbidity and mortality worldwide, accounting for about 9.6 million new cases and 1.5 million deaths annually. The poorest and socially excluded groups carry the largest burden of disease, which makes it essential to properly address the social determinants of health through poverty reduction measures and targeted interventions on high-risk populations. The spread of multidrug-resistance TB requires special attention and highlights the need to foster research on TB diagnostics, new drugs and vaccines. Although many advances have been made in the fight against TB over the last twenty years, a lot is still needed to achieve global elimination. The new end-TB strategy that was first launched in 2014 by the World Health Organization, is fully in line with the seventeen Sustainable Development Goals that came into effect since January 2016 and sets ambitious goals for the post-2015 agenda. A 90% reduction in TB-related mortality and an 80% decline in TB incidence within 2030 as well as the abolition of catastrophic expenditures for TB-affected people are the main targets of this strategy. Strong government commitment and adequate financing from all countries together with community engagement and appropriate investments in research are necessary in order to reach these objectives. PMID:27403269

  9. Advances in Ileitis Control, Diagnosis, Epidemiology and the Economic Impacts of Disease in Commercial Pig Herds

    Directory of Open Access Journals (Sweden)

    Alison M. Collins

    2013-09-01

    Full Text Available Proliferative enteropathy, commonly known as “ileitis” continues to be a significant production-limiting disease in pig herds throughout the world. The disease can be controlled with a combination of vaccination and antibiotic medication. However, pressure from consumers to reduce antibiotic use in livestock industries highlights the need to better understand the epidemiology of ileitis, the mechanisms of immunity, and to identify management factors that can reduce the load of Lawsonia intracellularis in both pigs and the environment. New diagnostic assays and economic modelling of ileitis will help producers target optimal treatment times and minimize the production losses associated with ileitis. This review aims to outline the current advances in disease diagnosis, epidemiology, control strategies and the economic impact of both clinical and sub-clinical disease.

  10. Paratransgenesis: a promising new strategy for mosquito vector control.

    Science.gov (United States)

    Wilke, André Barretto Bruno; Marrelli, Mauro Toledo

    2015-01-01

    The three main mosquito genera, Anopheles, Aedes and Culex, transmit respectively malaria, dengue and lymphatic filariasis. Current mosquito control strategies have proved unsuccessful, and there still is a substantial number of morbidity and mortality from these diseases. Genetic control methods have now arisen as promising alternative strategies, based on two approaches: the replacement of a vector population by disease-refractory mosquitoes and the release of mosquitoes carrying a lethal gene to suppress target populations. However, substantial hurdles and limitations need to be overcome if these methods are to be used successfully, the most significant being that a transgenic mosquito strain is required for every target species, making genetically modified mosquito strategies inviable when there are multiple vector mosquitoes in the same area. Genetically modified bacteria capable of colonizing a wide range of mosquito species may be a solution to this problem and another option for the control of these diseases. In the paratransgenic approach, symbiotic bacteria are genetically modified and reintroduced in mosquitoes, where they express effector molecules. For this approach to be used in practice, however, requires a better understanding of mosquito microbiota and that symbiotic bacteria and effector molecules be identified. Paratransgenesis could prove very useful in mosquito species that are inherently difficult to transform or in sibling species complexes. In this approach, a genetic modified bacteria can act by: (a) causing pathogenic effects in the host; (b) interfering with the host's reproduction; (c) reducing the vector's competence; and (d) interfering with oogenesis and embryogenesis. It is a much more flexible and adaptable approach than the use of genetically modified mosquitoes because effector molecules and symbiotic bacteria can be replaced if they do not achieve the desired result. Paratransgenesis may therefore become an important integrated

  11. DC Voltage Balance Control Strategy for Medium Voltage Cascaded STATCOM Based on Distributed Control

    Directory of Open Access Journals (Sweden)

    Xuehua Zhao

    2014-01-01

    Full Text Available DC bus capacitors of Medium Voltage Cascaded STATCOM are independent. DC side voltage balance control method is the key influencing factor of current control. The imbalance of DC bus voltage increases harmonic current and affects the safety of device. In this paper, the unbalance mechanism of DC side capacitor voltage is analyzed. Based on the unipolar dual frequency and carrier phase-shifted SPWM (CPS-SPWM modulation algorithms, the distributed control algorithms, which need multi- FPGA structure, are proposed. By changing the instantaneous active power input of single module, the voltage balance control strategies of DC bus capacitors are realized. The strategy can be applied in each inverter, respectively. Simulation and experiment results show the feasibility and effectiveness of the strategy

  12. Control strategy of maglev vehicles based on particle swarm algorithm

    Institute of Scientific and Technical Information of China (English)

    Hui Wang; Gang Shen; Jinsong Zhou

    2014-01-01

    Taking a single magnet levitation system as the object, a nonlinear numerical model of the vehicle-guide-way coupling system was established to study the levitation control strategies. According to the similarity in dynamics, the single magnet-guideway coupling system was simpli-fied into a magnet-suspended track system, and the corre-sponding hardware-in-loop test rig was set up using dSPACE. A full-state-feedback controller was developed using the levitation gap signal and the current signal, and controller parameters were optimized by particle swarm algorithm. The results from the simulation and the test rig show that, the proposed control method can keep the sys-tem stable by calculating the controller output with the full-state information of the coupling system, Step responses from the test rig show that the controller can stabilize the system within 0.15 s with a 2% overshot, and performs well even in the condition of violent external disturbances. Unlike the linear quadratic optimal method, the particle swarm algorithm carries out the optimization with the nonlinear controlled object included, and its optimized results make the system responses much better.

  13. Strategies for controlling methicillin-resistant Staphylococcus aureus in hospitals.

    Science.gov (United States)

    Boyce, J M

    1995-07-01

    In areas where the prevalence of methicillin-resistant Staphylococcus aureus (MRSA) is very low, aggressive strategies, which appear to have been effective, such as those used in the Netherlands and western Australia, may be feasible. In hospitals where MRSA is epidemic or highly endemic, less rigorous strategies are appropriate. However, which isolation techniques and barrier precautions are optimal is controversial. In addition, there is no consensus regarding the epidemiological importance of environmental contamination. Rapid detection of MRSA, prompt implementation of barrier precautions and prospective surveillance are essential components of a successful control programme. Eradicating nasal carriage of MRSA among patients and personnel can be useful during epidemics, but the cost-effectiveness of using this approach in hospitals where the prevalence of MRSA is low is unknown. Additional studies of this issue need to include surveillance for mupirocin-resistant strains.

  14. Congestion Control Strategy for Opportunistic Network Based on Message Values

    Directory of Open Access Journals (Sweden)

    Deng-yin Zhang

    2014-05-01

    Full Text Available To solve the congestion problem in opportunistic networks, a congestion control strategy based on message deleting and transferring(DATM is proposed. The congested node calculates the storage value of each message according to the forwarding probability and TTL of message, then deletes the message with the minimum storage value and transfers the message with the minimum forwarding probability to neighboring nodes. The neighboring nodes calculate the receiving value of the message according to the forwarding probability and free buffer capacity of this message. The congested node transfers the message to the neighboring node with the maximum receiving value. The message will be deleted when there is no neighboring node to receive it. The algorithm is more targeted at deleting messages. Besides, it combines the strategy of transferring message. Therefore, it can deal with the congestion more efficiently. The message arrival rate is improved significantly and the end-to-end delay is also reduced to some extent.

  15. Controls on Extreme Droughts and Adaptation Strategies in Semiarid Regions

    Science.gov (United States)

    Scanlon, B. R.; Cook, C.; Fernando, D. N.; LeBlanc, M.

    2012-12-01

    Increasing vulnerability to droughts with reduced per capita water storage, particularly in semiarid regions, underscores the need for predictive understanding of drought controls and development of adaptation strategies for water resources management. In this study we evaluate causes of major droughts in southwest and southcentral US (California and Texas) and southeast Australia (Murray Darling Basin). Impacts of climate cycles (ENSO, PDO, AMO, NAO, IOD) and atmospheric circulation on drought initiation and persistence are examined. Effects of drought on surface water reservoir storage, groundwater storage, irrigation, and crop production are compared. Adaptation strategies being evaluated include water transfers among sectors, particularly from irrigated agriculture to other groups, increasing storage using managed aquifer recharge, water reuse, and development of new water sources (e.g. seawater desalination). It is critical to develop a broad portfolio of water sources to increase resilience to future droughts.

  16. Preparation of controlled gold nanoparticle aggregates using a dendronization strategy.

    Science.gov (United States)

    Paez, Julieta I; Coronado, Eduardo A; Strumia, Miriam C

    2012-10-15

    In this work, a dendronization strategy was used to control interparticle spacing and the optical properties of gold nanoparticle (NP) aggregates in aqueous media. To achieve this goal, two dendritic disulfides bearing different functionalities on their periphery were synthesized and used as ligands to dendronize gold NPs. The dendronized NPs then undergo aggregation; this process was followed by UV-vis spectroscopy, dynamic light scattering (DLS), and transmission electronic microscopy (TEM) measurements and correlated with Generalized Mie Theory electrodynamics calculations. For comparison, NP functionalization was also studied using a nondendritic ligand. It was found that the use of dendritic disulfides allows for the preparation of controlled NP aggregates. This study demonstrates how different dendronization parameters, such as disulfide concentration, temperature, time and nature of the ligand (dendritic vs nondendritic), determine the control exerted over the size and stability of the NP aggregates.

  17. Second Generation Advanced Reburning for High Efficiency NOx Control

    Energy Technology Data Exchange (ETDEWEB)

    Vladimir M. Zamansky; Peter M. Maly; Vitali V. Lissianski; Mark S. Sheldon; David Moyeda; Roy Payne

    2001-06-30

    This project develops a family of novel Second Generation Advanced Reburning (SGAR) NO{sub x} control technologies, which can achieve 95% NO{sub x} control in coal fired boilers at a significantly lower cost than Selective Catalytic Reduction (SCR). The conventional Advanced Reburning (AR) process integrates basic reburning and N-agent injection. The SGAR systems include six AR variants: (1) AR-Lean--injection of the N-agent and promoter along with overfire air; (2) AR-Rich--injection of N-agent and promoter into the reburning zone; (3) Multiple Injection Advanced Reburning (MIAR)--injection of N-agents and promoters both into the reburning zone and with overfire air; (4) AR-Lean + Promoted SNCR--injection of N-agents and promoters with overfire air and into the temperature zone at which Selective Non-Catalytic Reduction (SNCR) is effective; (5) AR-Rich + Promoted SNCR--injection of N-agents and promoters into the reburning zone and into the SNCR zone; and (6) Promoted Reburning + Promoted SNCR--basic or promoted reburning followed by basic or promoted SNCR process. The project was conducted in two phases over a five-year period. The work included a combination of analytical and experimental studies to confirm the process mechanisms, identify optimum process configurations, and develop a design methodology for full-scale applications. Phase I was conducted from October, 1995 to September, 1997 and included both analytical studies and tests in bench and pilot-scale test rigs. Phase I moved AR technology to Maturity Level III-Major Subsystems. Phase II is conducted over a 45 month period (October, 1997-June, 2001). Phase II included evaluation of alternative promoters, development of alternative reburning fuel and N-Agent jet mixing systems, and scale up. The goal of Phase II was to move the technology to Maturity Level I-Subscale Integrated System. Tests in combustion facility ranging in firing rate from 0.1 x 10{sup 6} to 10 x 10{sup 6} Btu/hr demonstrated the

  18. Automatic Control Strategy Development for the Supercritical CO2 Brayton Cycle for LFR Autonomous Load Following

    International Nuclear Information System (INIS)

    The supercritical carbon dioxide (S-CO2) Brayton cycle is a promising advanced alternative to the Rankine saturated steam cycle and ideal gas Brayton cycle for the energy converters of specific reactor concepts belonging to the U.S. Department of Energy Generation IV Nuclear Energy Systems Initiative. A new plant dynamics analysis computer code has been developed for simulation of the S-CO2 Brayton cycle coupled to an autonomous Lead-Cooled Fast Reactor (LFR). The plant dynamics code was used to develop an automatic control strategy for the whole plant in response to changes in the demand from the electrical grid. The specific features of the S-CO2 Brayton cycle that result in limitations on the control range and speed of specific control mechanisms are discussed. Calculations of whole-plant responses to plant operational transients involving step and continuous changes in grid demand are demonstrated. (authors)

  19. MERCURY CONTROL WITH THE ADVANCED HYBRID PARTICULATE COLLECTOR

    Energy Technology Data Exchange (ETDEWEB)

    Charlene R. Crocker; Steven A. Benson; Stanley J. Miller

    2003-11-01

    This project was awarded under U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Program Solicitation DE-PS26-00NT40769 and specifically addresses Technical Topical Area 4--Testing Novel and Less Mature Control Technologies on Actual Flue Gas at the Pilot Scale. The project team includes the Energy & Environmental Research Center (EERC) as the main contractor; W.L. Gore & Associates, Inc., as a technical and financial partner; and the Big Stone Plant operated by Otter Tail Power Company, host for the field-testing portion of the research. Since 1995, DOE has supported development of a new concept in particulate control called the advanced hybrid particulate collector (AHPC). The AHPC has been licensed to W.L. Gore & Associates, Inc., and is now marketed as the Advanced Hybrid{trademark} filter by Gore. The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The AHPC provides ultra-high collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The AHPC appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas-solid contactor. The objective of the original 5-task project is to demonstrate 90% total mercury control in the AHPC at a lower cost than current mercury control estimates. The approach includes bench-scale batch testing that ties the new work to previous results and links results with larger-scale pilot testing with real flue gas on a coal-fired combustion system, pilot-scale testing on a coal-fired combustion system with both a pulse-jet baghouse and an AHPC to prove or disprove the research hypotheses, and field demonstration pilot-scale testing at a

  20. MERCURY CONTROL WITH THE ADVANCED HYBRID PARTICULATE COLLECTOR

    Energy Technology Data Exchange (ETDEWEB)

    Steven A. Benson; Stanley J. Miller; Charlene R. Crocker; Kevin C. Galbreath; Jason D. Laumb; Jill M. Zola; Ye Zhuang; Michelle R. Olderbak

    2004-08-01

    This project was awarded under U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Program Solicitation DE-PS26-00NT40769 and specifically addresses Technical Topical Area 4-Testing Novel and Less Mature Control Technologies on Actual Flue Gas at the Pilot Scale. The project team includes the Energy & Environmental Research Center (EERC) as the main contractor; W.L. Gore & Associates, Inc., as a technical and financial partner; and the Big Stone Plant operated by Otter Tail Power Company, host for the field-testing portion of the research. Since 1995, DOE has supported development of a new concept in particulate control called the advanced hybrid particulate collector (AHPC). The AHPC has been licensed to W.L. Gore & Associates, Inc., and is now marketed as the Advanced Hybrid{trademark} filter by Gore. The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The AHPC provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The AHPC appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas-solid contactor. The objective of the original 5-task project is to demonstrate 90% total mercury control in the AHPC at a lower cost than current mercury control estimates. The approach includes bench-scale batch testing that ties the new work to previous results and links results with larger-scale pilot testing with real flue gas on a coal-fired combustion system, pilot-scale testing on a coal-fired combustion system with both a pulse-jet baghouse and an AHPC to prove or disprove the research hypotheses, and field demonstration pilot-scale testing at a

  1. Fault diagnosis and fault-tolerant control strategies for non-linear systems analytical and soft computing approaches

    CERN Document Server

    Witczak, Marcin

    2014-01-01

      This book presents selected fault diagnosis and fault-tolerant control strategies for non-linear systems in a unified framework. In particular, starting from advanced state estimation strategies up to modern soft computing, the discrete-time description of the system is employed Part I of the book presents original research results regarding state estimation and neural networks for robust fault diagnosis. Part II is devoted to the presentation of integrated fault diagnosis and fault-tolerant systems. It starts with a general fault-tolerant control framework, which is then extended by introducing robustness with respect to various uncertainties. Finally, it is shown how to implement the proposed framework for fuzzy systems described by the well-known Takagi–Sugeno models. This research monograph is intended for researchers, engineers, and advanced postgraduate students in control and electrical engineering, computer science,as well as mechanical and chemical engineering.

  2. Advanced overlay: sampling and modeling for optimized run-to-run control

    Science.gov (United States)

    Subramany, Lokesh; Chung, WoongJae; Samudrala, Pavan; Gao, Haiyong; Aung, Nyan; Gomez, Juan Manuel; Gutjahr, Karsten; Park, DongSuk; Snow, Patrick; Garcia-Medina, Miguel; Yap, Lipkong; Demirer, Onur Nihat; Pierson, Bill; Robinson, John C.

    2016-03-01

    In recent years overlay (OVL) control schemes have become more complicated in order to meet the ever shrinking margins of advanced technology nodes. As a result, this brings up new challenges to be addressed for effective run-to- run OVL control. This work addresses two of these challenges by new advanced analysis techniques: (1) sampling optimization for run-to-run control and (2) bias-variance tradeoff in modeling. The first challenge in a high order OVL control strategy is to optimize the number of measurements and the locations on the wafer, so that the "sample plan" of measurements provides high quality information about the OVL signature on the wafer with acceptable metrology throughput. We solve this tradeoff between accuracy and throughput by using a smart sampling scheme which utilizes various design-based and data-based metrics to increase model accuracy and reduce model uncertainty while avoiding wafer to wafer and within wafer measurement noise caused by metrology, scanner or process. This sort of sampling scheme, combined with an advanced field by field extrapolated modeling algorithm helps to maximize model stability and minimize on product overlay (OPO). Second, the use of higher order overlay models means more degrees of freedom, which enables increased capability to correct for complicated overlay signatures, but also increases sensitivity to process or metrology induced noise. This is also known as the bias-variance trade-off. A high order model that minimizes the bias between the modeled and raw overlay signature on a single wafer will also have a higher variation from wafer to wafer or lot to lot, that is unless an advanced modeling approach is used. In this paper, we characterize the bias-variance trade off to find the optimal scheme. The sampling and modeling solutions proposed in this study are validated by advanced process control (APC) simulations to estimate run-to-run performance, lot-to-lot and wafer-to- wafer model term monitoring to

  3. Advanced Branching Control and Characterization of Inorganic Semiconducting Nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, Steven Michael [Univ. of California, Berkeley, CA (United States)

    2007-01-01

    The ability to finely tune the size and shape of inorganic semiconducting nanocrystals is an area of great interest, as the more control one has, the more applications will be possible for their use. The first two basic shapes develped in nanocrystals were the sphere and the anistropic nanorod. the II_VI materials being used such as Cadmium Selenide (CdSe) and Cadmium Telluride (CdTe), exhibit polytypism, which allows them to form in either the hexagonally packed wurtzite or cubically packed zinc blende crystalline phase. The nanorods are wurtzite with the length of the rod growing along the c-axis. As this grows, stacking faults may form, which are layers of zinc blende in the otherwise wurtzite crystal. Using this polytypism, though, the first generation of branched crystals were developed in the form of the CdTe tetrapod. This is a nanocrystal that nucleates in the zincblend form, creating a tetrahedral core, on which four wurtzite arms are grown. This structure opened up the possibility of even more complex shapes and applications. This disseration investigates the advancement of branching control and further understanding the materials polytypism in the form of the stacking faults in nanorods.

  4. Advanced illumination control algorithm for medical endoscopy applications

    Science.gov (United States)

    Sousa, Ricardo M.; Wäny, Martin; Santos, Pedro; Morgado-Dias, F.

    2015-05-01

    CMOS image sensor manufacturer, AWAIBA, is providing the world's smallest digital camera modules to the world market for minimally invasive surgery and one time use endoscopic equipment. Based on the world's smallest digital camera head and the evaluation board provided to it, the aim of this paper is to demonstrate an advanced fast response dynamic control algorithm of the illumination LED source coupled to the camera head, over the LED drivers embedded on the evaluation board. Cost efficient and small size endoscopic camera modules nowadays embed minimal size image sensors capable of not only adjusting gain and exposure time but also LED illumination with adjustable illumination power. The LED illumination power has to be dynamically adjusted while navigating the endoscope over changing illumination conditions of several orders of magnitude within fractions of the second to guarantee a smooth viewing experience. The algorithm is centered on the pixel analysis of selected ROIs enabling it to dynamically adjust the illumination intensity based on the measured pixel saturation level. The control core was developed in VHDL and tested in a laboratory environment over changing light conditions. The obtained results show that it is capable of achieving correction speeds under 1 s while maintaining a static error below 3% relative to the total number of pixels on the image. The result of this work will allow the integration of millimeter sized high brightness LED sources on minimal form factor cameras enabling its use in endoscopic surgical robotic or micro invasive surgery.

  5. Strategies to water pollution control in western China

    Institute of Scientific and Technical Information of China (English)

    JIANGWenchao; CHENGJijian; LONGTengrui; HEQiang

    2003-01-01

    Problems of and main limiting factors to Chinese western eco-environment are analyzea firstly and principles of integrating water pollution control with water resources planning and management, with ecological construction and with economic development planning and setting control priorities according to local conditions are proposed. Following strategies for water pollution control are suggested: 1) a master plan for western area need to be established as soon as possible; 2) total emission control should be regarded as the basic policy and measures such as clean production, charging and subsidy need to be implemented; 3) point sources pollution control should be considered the main task in short term and centralized wasteweter treatment plants by using sustainable processes should be constructed primarily for large and medium-size cities with heavier pollution; 4) sound institutional and regulation systems need to be established to create an enabling environment; 5) multiple investment system should be established; and 6) studies of pragmatic theories and methodologies for water pollution control and cost-effective technologies appropriate to western area, and training of local technicians need to be enhanced as well.

  6. Current status of decommissioning projects and their strategies in advanced countries

    Energy Technology Data Exchange (ETDEWEB)

    Chung, U. S.; Lee, K. W.; Hwang, D. S.; Park, S. K.; Hwang, S. T.; Paik, S. T.; Park, J. H.; Choi, Y. D.; Chung, K. H.; Lee, K. I.; Hong, S. B

    2007-06-15

    At the Korea Atomic Energy Research Institute(KAERI), two projects for decommissioning of the research reactors and uranium conversion plant are carried out. The number of nuclear facilities to be dismantled will be much increased in future and the decommissioning industries will be enlarged. Keeping pace with this increasing tendency, each country formulated their own strategies and regulation systems, and applied their own technologies. The international organizations such as the IAEA and the OECD/NEA also prepared standards in technologies and regulation upon decommissioning and recommended to adopt them to the decommissioning projects. These strategies and technologies are very different country by country due to the different site dependent conditions and it will not be reasonable to evaluate their merits and weakness. The world wide status of the decommissioning, highlighted on that of 5 countries of USA, UK, France, Germany and Japan because they are advanced counties in nuclear industries, are summarized and their site specific conditions are evaluated. The scopes of the evaluation are decommissioning strategies, licensing procedures and requirements focused on decommissioning plan, waste management, technology development and so on. The detailed decommissioning progresses of several typical example sites were introduced. The activities on decommissioning field of the international organization, increased according to the enlarged decommissioning industries, are also summarized.

  7. Current status of decommissioning projects and their strategies in advanced countries

    International Nuclear Information System (INIS)

    At the Korea Atomic Energy Research Institute(KAERI), two projects for decommissioning of the research reactors and uranium conversion plant are carried out. The number of nuclear facilities to be dismantled will be much increased in future and the decommissioning industries will be enlarged. Keeping pace with this increasing tendency, each country formulated their own strategies and regulation systems, and applied their own technologies. The international organizations such as the IAEA and the OECD/NEA also prepared standards in technologies and regulation upon decommissioning and recommended to adopt them to the decommissioning projects. These strategies and technologies are very different country by country due to the different site dependent conditions and it will not be reasonable to evaluate their merits and weakness. The world wide status of the decommissioning, highlighted on that of 5 countries of USA, UK, France, Germany and Japan because they are advanced counties in nuclear industries, are summarized and their site specific conditions are evaluated. The scopes of the evaluation are decommissioning strategies, licensing procedures and requirements focused on decommissioning plan, waste management, technology development and so on. The detailed decommissioning progresses of several typical example sites were introduced. The activities on decommissioning field of the international organization, increased according to the enlarged decommissioning industries, are also summarized

  8. Control strategies for afterload reduction with an artificial vasculature device.

    Science.gov (United States)

    Giridharan, Guruprasad A; Cheng, Rolando Chip; Glower, Jacob S; Ewert, Daniel L; Sobieski, Michael A; Slaughter, Mark S; Koenig, Steven C

    2012-01-01

    Ventricular assist devices (VADs) have been used successfully as a bridge to transplant in heart failure patients by unloading ventricular volume and restoring the circulation. An artificial vasculature device (AVD) is being developed that may better facilitate myocardial recovery than VAD by controlling the afterload experienced by the native heart and controlling the pulsatile energy entering into the arterial system from the device, potentially reconditioning the arterial system properties. The AVD is a valveless, 80 ml blood chamber with a servo-controlled pusher plate connected to the ascending aorta by a vascular graft. Control algorithms for the AVD were developed to maintain any user-defined systemic input impedance (IM) including resistance, elastance, and inertial components. Computer simulation and mock circulation models of the cardiovascular system were used to test the efficacy of two control strategies for the AVD: 1) average impedance position control (AIPC)-to maintain an average value of resistance during left ventricular (LV) systole and 2) instantaneous impedance force feedback (IIFF) and position control (IIPC)-to maintain a desired value or profile of resistance and compliance. Computer simulations and mock loop tests were performed to predict resulting cardiovascular pressures, volumes, flows, and the resistance and compliance experienced by the native LV during ejection for simulated normal, failing, and recovering LV. These results indicate that the LV volume and pressure decreased, and the LV stroke volume increased with decreasing IM, resulting in an increased ejection fraction. Although the AIPC algorithm is more stable and can tolerate higher levels of sensor errors and noise, the IIFF and IIPC control algorithms are better suited to maintain any instantaneous IM or an IM profile. The developed AVD impedance control algorithms may be implemented with current VADs to promote myocardial recovery and facilitate weaning.

  9. Control strategies for afterload reduction with an artificial vasculature device.

    Science.gov (United States)

    Giridharan, Guruprasad A; Cheng, Rolando Chip; Glower, Jacob S; Ewert, Daniel L; Sobieski, Michael A; Slaughter, Mark S; Koenig, Steven C

    2012-01-01

    Ventricular assist devices (VADs) have been used successfully as a bridge to transplant in heart failure patients by unloading ventricular volume and restoring the circulation. An artificial vasculature device (AVD) is being developed that may better facilitate myocardial recovery than VAD by controlling the afterload experienced by the native heart and controlling the pulsatile energy entering into the arterial system from the device, potentially reconditioning the arterial system properties. The AVD is a valveless, 80 ml blood chamber with a servo-controlled pusher plate connected to the ascending aorta by a vascular graft. Control algorithms for the AVD were developed to maintain any user-defined systemic input impedance (IM) including resistance, elastance, and inertial components. Computer simulation and mock circulation models of the cardiovascular system were used to test the efficacy of two control strategies for the AVD: 1) average impedance position control (AIPC)-to maintain an average value of resistance during left ventricular (LV) systole and 2) instantaneous impedance force feedback (IIFF) and position control (IIPC)-to maintain a desired value or profile of resistance and compliance. Computer simulations and mock loop tests were performed to predict resulting cardiovascular pressures, volumes, flows, and the resistance and compliance experienced by the native LV during ejection for simulated normal, failing, and recovering LV. These results indicate that the LV volume and pressure decreased, and the LV stroke volume increased with decreasing IM, resulting in an increased ejection fraction. Although the AIPC algorithm is more stable and can tolerate higher levels of sensor errors and noise, the IIFF and IIPC control algorithms are better suited to maintain any instantaneous IM or an IM profile. The developed AVD impedance control algorithms may be implemented with current VADs to promote myocardial recovery and facilitate weaning. PMID:22635010

  10. Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement.

    Science.gov (United States)

    Shatkin, J A; Ong, Kimberly J; Beaudrie, Christian; Clippinger, Amy J; Hendren, Christine Ogilvie; Haber, Lynne T; Hill, Myriam; Holden, Patricia; Kennedy, Alan J; Kim, Baram; MacDonell, Margaret; Powers, Christina M; Sharma, Monita; Sheremeta, Lorraine; Stone, Vicki; Sultan, Yasir; Turley, Audrey; White, Ronald H

    2016-08-01

    The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article.

  11. Advancing Risk Analysis for Nanoscale Materials: Report from an International Workshop on the Role of Alternative Testing Strategies for Advancement.

    Science.gov (United States)

    Shatkin, J A; Ong, Kimberly J; Beaudrie, Christian; Clippinger, Amy J; Hendren, Christine Ogilvie; Haber, Lynne T; Hill, Myriam; Holden, Patricia; Kennedy, Alan J; Kim, Baram; MacDonell, Margaret; Powers, Christina M; Sharma, Monita; Sheremeta, Lorraine; Stone, Vicki; Sultan, Yasir; Turley, Audrey; White, Ronald H

    2016-08-01

    The Society for Risk Analysis (SRA) has a history of bringing thought leadership to topics of emerging risk. In September 2014, the SRA Emerging Nanoscale Materials Specialty Group convened an international workshop to examine the use of alternative testing strategies (ATS) for manufactured nanomaterials (NM) from a risk analysis perspective. Experts in NM environmental health and safety, human health, ecotoxicology, regulatory compliance, risk analysis, and ATS evaluated and discussed the state of the science for in vitro and other alternatives to traditional toxicology testing for NM. Based on this review, experts recommended immediate and near-term actions that would advance ATS use in NM risk assessment. Three focal areas-human health, ecological health, and exposure considerations-shaped deliberations about information needs, priorities, and the next steps required to increase confidence in and use of ATS in NM risk assessment. The deliberations revealed that ATS are now being used for screening, and that, in the near term, ATS could be developed for use in read-across or categorization decision making within certain regulatory frameworks. Participants recognized that leadership is required from within the scientific community to address basic challenges, including standardizing materials, protocols, techniques and reporting, and designing experiments relevant to real-world conditions, as well as coordination and sharing of large-scale collaborations and data. Experts agreed that it will be critical to include experimental parameters that can support the development of adverse outcome pathways. Numerous other insightful ideas for investment in ATS emerged throughout the discussions and are further highlighted in this article. PMID:27510619

  12. Second Generation Advanced Reburning for High Efficiency NOx Control

    International Nuclear Information System (INIS)

    Energy and Environmental Research Corporation is developing a family of high efficiency and low cost NOx control technologies for coal fired utility boilers based on Advanced Reburning (AR), a synergistic integration of basic reburning with injection of an N-agent. In conventional AR, injection of the reburn fuel is followed by simultaneous N-agent and overfire air injection. The second generation AR systems incorporate several components which can be used in different combinations. These components include: (1) Reburning Injection of the reburn fuel and overfire air. (2) N-agent Injection The N-agent (ammonia or urea) can be injected at different locations: into the reburning zone, along with the overfire air, and downstream of the overfire air injection. (3) N-agent Promotion Several sodium compounds can considerably enhance the NOx control from N-agent injection. These ''promoters'' can be added to aqueous N-agents. (4) Two Stages of N-agent Injection and Promotion Two N-agents with or without promoters can be injected at different locations for deeper NOx control. AR systems are intended for post-RACT applications in ozone non-attainment areas where NOx control in excess of 80% is required. AR will provide flexible installations that allow NOx levels to be lowered when regulations become more stringent. The total cost of NOx control for AR systems is approximately half of that for SCR. Experimental and kinetic modeling results for development of these novel AR systems are presented. Tests have been conducted in a 1.0 MMBtu/hr Boiler Simulator Facility with coal as the main fuel and natural gas as the reburning fuel. The results show that high efficiency NOx control, in the range 84-95%, can be achieved with various elements of AR. A comparative byproduct emission study was performed to compare the emissions from different variants of AR with commercial technologies (reburning and SNCR). For each technology sampling included: CO, SO2, N2O, total hydrocarbons, NH

  13. Indoor radon and decay products: Concentrations, causes, and control strategies

    Energy Technology Data Exchange (ETDEWEB)

    Nero, A.V.; Gadgil, A.J.; Nazaroff, W.W.; Revzan, K.L.

    1990-11-01

    This report is another in the on going technical report series that addresses various aspects of the DOE Radon Research Program. It provides an overview of what is known about the behavior of radon and its decay products in the indoor environment and examines the manner in which several important classes of factors -- structural, geological, and meteorological -- affect indoor radon concentrations. Information on US indoor radon concentrations, currently available monitoring methods and novel radon control strategies are also explored. 238 refs., 22 figs., 9 tabs.

  14. A rapid approach to rational water pollution control strategies.

    Science.gov (United States)

    Economopoulos, A P

    1996-10-01

    The formulation of rational wastewater control strategies is becoming increasingly important in many countries where, exploding urbanization, industrialization and/or tourism, often combined with improved standards of living and better awareness of the environmental problems, are resulting in enlarged pollution problems, but also in the availability of expanding financial resources for environmental protection. However, more often than one tends to believe, lack of planning, or planning with limited understanding of the principles involved, has resulted in solutions that are both expensive and incapable of addressing the key problems.As rigorous planning is extremely resource intensive, and for this reason impractical for most study areas, the development of a much simplified analysis procedure, capable of generating rational, near-optimum, strategies and detailed action programs, is required, if proper environmental management is to be widely practiced.In an effort to achieve the above objectives, a systems analysis approach is selected as the most suitable at rationalizing the allocation of available resources and at producing detailed action programs that promote implementation. In the context of this approach, new, easy to use models have been developed, while others, have been selected, adapted and streamlined in their use. The entire problem analysis and strategy synthesis procedures have thus been simplified and defined to a degree appropriate for widespread use, and the resultant procedure is actively promoted by WHO and UNEP.

  15. A unified control strategy for the active reduction of sound and vibration

    NARCIS (Netherlands)

    Doelman, N.J.

    1991-01-01

    The generalized minimum variance (GMV) control strategy is proposed as an effective strategy for active sound and vibration control systems. The GMV strategy is shown to unify well-known adaptive filtering approaches based on LMS-type algorithms and purely feedback strategies as used in other types

  16. Arm coordination in octopus crawling involves unique motor control strategies.

    Science.gov (United States)

    Levy, Guy; Flash, Tamar; Hochner, Binyamin

    2015-05-01

    To cope with the exceptional computational complexity that is involved in the control of its hyper-redundant arms [1], the octopus has adopted unique motor control strategies in which the central brain activates rather autonomous motor programs in the elaborated peripheral nervous system of the arms [2, 3]. How octopuses coordinate their eight long and flexible arms in locomotion is still unknown. Here, we present the first detailed kinematic analysis of octopus arm coordination in crawling. The results are surprising in several respects: (1) despite its bilaterally symmetrical body, the octopus can crawl in any direction relative to its body orientation; (2) body and crawling orientation are monotonically and independently controlled; and (3) contrasting known animal locomotion, octopus crawling lacks any apparent rhythmical patterns in limb coordination, suggesting a unique non-rhythmical output of the octopus central controller. We show that this uncommon maneuverability is derived from the radial symmetry of the arms around the body and the simple pushing-by-elongation mechanism by which the arms create the crawling thrust. These two together enable a mechanism whereby the central controller chooses in a moment-to-moment fashion which arms to recruit for pushing the body in an instantaneous direction. Our findings suggest that the soft molluscan body has affected in an embodied way [4, 5] the emergence of the adaptive motor behavior of the octopus.

  17. Improved Control Strategy for Microgrid Ultracapacitor Energy Storage Systems

    Directory of Open Access Journals (Sweden)

    Xiaobo Dou

    2014-12-01

    Full Text Available Ultracapacitors (UCs, with their features of high power density and high current charge-discharge, have become the best choice for dynamic power compensation to improve the stability of microgrids and are increasingly being applied in microgrids. This paper presents the control of an energy storage system (ESS based on ultracapacitors in the context of grid-connected microgrids. The ESS is composed of DC/AC and DC/DC converters tied by a dc link. An improved dynamic model for the ESS is proposed. Based on the proposed model a Proportional-Integral-Resonant (PIR DC link voltage controller is proposed to maintain the DC link voltage through the charging-discharging control of ultracapacitors, capable of working properly under all operating conditions. An extra double frequency component is injected into the UC current by a R controller to dynamically compensate for DC instantaneous power and double frequency AC instantaneous power due to unbalanced grid conditions and disturbances. This feature maintains the DC link voltage constant under unbalanced conditions and increases the degrees of freedom of the DC/AC converter and thus facilitates the application of UCs in microgrids. Simulation and experimental results verify the effectiveness of the proposed control strategy.

  18. Eutrophication status and control strategy of Taihu Lake

    Institute of Scientific and Technical Information of China (English)

    Limin ZHANG; Minfang XIA; Lei ZHANG; Chun WANG; Jilai LU

    2008-01-01

    The water quality and eutrophication status of Taihu Lake in recent years are presented and the pollution trends are analyzed. It is shown that because of unreas-onable industrial structures, pollution discharge per GDP is high within the Taihu basin, and the pollution discharge from point and-non-point sources exceed the basin's environmental carrying capacity. Especially, excessive pollutants containing nitrgogen and phosphorus are being discharged. Moreover, eutrophication may also result from internal pollution sources such as the release of nutrient elements from sediment. All these factors have resulted in-the water quality deterioration of Taihu Lake. To solve this environmental problem, possible con-trol strategies are summarized, including the control of internal pollution sources and inflow-river pollution, eco-logical restoration and reconstruction of the degraded lakeside zone ecosystem, clean water diversion, dredging, and manual algae removal.

  19. Strategy for ecologic control in fighting Varroa destructor

    Directory of Open Access Journals (Sweden)

    Stanimirović Zoran

    2007-01-01

    Full Text Available The ectoparasite Varroa destructor is one of the most wide-spread parasites of the honey bee, which is increasing its resistence to traditional synthetic acaricides more and more with each year. New regulations on quality of the European Union ban the presence of residue in bee products, which rules out the use of chemical means in the course of the honey harvest. The concept of ecologic control of Varroa destructor in honey bee colonies implies the complementary use of adequate biotechnical and biophysical measures and treatments using preparations based on etheric oils and organic acids. The combination of these treatments according to the presented strategy makes it possible to keep varroasis under control.

  20. Operational controlling - a tool of translating strategy into action

    Directory of Open Access Journals (Sweden)

    2011-03-01

    Full Text Available . Enterprises have a lot of problems with realization their strategic aims in the fast changing and competitive business arena from many years. Effective execution of strategic plan needs its translating into action, task results and indicators of everyday activities. The success on the market is attainable by communicating strategic and operating goals on the each level of organizational structure and their connecting with budget of units or employee motivation. The scorecards balancing in finance, customer, process and development perspectives is very useful for pointing - what do we control with? or - what do we have to achieve? But doesn't answer to question about ways of enterprise managing. Main aim of the article is proving that operational controlling system is a essential tool for translating strategy into action. The Balanced Scorecard methodology should to take into consideration system and process connection of enterprise with procurement, co-operation or distribution supply chain also.

  1. A controllable stitch layout strategy for random needle embroidery

    Institute of Scientific and Technical Information of China (English)

    Jie ZHOU; Zheng-xing SUN; Ke-wei YANG

    2014-01-01

    Random needle embroidery (RNE) is a graceful art enrolled in the world intangible cultural heritage. In this paper, we study the stitch layout problem and propose a controllable stitch layout strategy for RNE. Using our method, a user can easily change the layout styles by adjusting several high-level layout parameters. This approach has three main features:firstly, a stitch layout rule containing low-level stitch attributes and high-level layout parameters is designed;secondly, a stitch neighborhood graph is built for each region to model the spatial relationship among stitches;thirdly, different stitch attributes (orientations, lengths, and colors) are controlled using different reaction-diffusion processes based on a stitch neighborhood graph. Moreover, our method supports the user in changing the stitch orientation layout by drawing guide curves interactively. The experimental results show its capability for reflecting various stitch layout styles and flexibility for user interaction.

  2. Prospects for advancing tuberculosis control efforts through novel therapies.

    Directory of Open Access Journals (Sweden)

    Joshua A Salomon

    2006-08-01

    Full Text Available BACKGROUND: Development of new, effective, and affordable tuberculosis (TB therapies has been identified as a critical priority for global TB control. As new candidates emerge from the global TB drug pipeline, the potential impacts of novel, shorter regimens on TB incidence and mortality have not yet been examined. METHODS AND FINDINGS: We used a mathematical model of TB to evaluate the expected benefits of shortening the duration of effective chemotherapy for active pulmonary TB. First, we considered general relationships between treatment duration and TB dynamics. Next, as a specific example, we calibrated the model to reflect the current situation in the South-East Asia region. We found that even with continued and rapid progress in scaling up the World Health Organization's DOTS strategy of directly observed, short-course chemotherapy, the benefits of reducing treatment duration would be substantial. Compared to a baseline of continuing DOTS coverage at current levels, and with currently available tools, a 2-mo regimen introduced by 2012 could prevent around 20% (range 13%-28% of new cases and 25% (range 19%-29% of TB deaths in South-East Asia between 2012 and 2030. If effective treatment with existing drugs expands rapidly, overall incremental benefits of shorter regimens would be lower, but would remain considerable (13% [range 8%-19%] and 19% [range 15%-23%] reductions in incidence and mortality, respectively, between 2012 and 2030. A ten-year delay in the introduction of new drugs would erase nearly three-fourths of the total expected benefits in this region through 2030. CONCLUSIONS: The introduction of new, shorter treatment regimens could dramatically accelerate the reductions in TB incidence and mortality that are expected under current regimens-with up to 2- or 3-fold increases in rates of decline if shorter regimens are accompanied by enhanced case detection. Continued progress in reducing the global TB burden will require a

  3. Standards and the design of the Advanced Photon Source control system

    International Nuclear Information System (INIS)

    The Advanced Photon Source (APS), now under construction at Argonne National Laboratory is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. In the conceptual stage the control system design group faced the challenges that face all control system designers: to force the machine designers to quantify and codify the system requirements, to protect the investment in hardware and software from rapid obsolescence, and to find methods of quickly incorporating new generations of equipment and replace of obsolete equipment without disrupting the exiting system. To solve these and related problems, the APS control system group made an early resolution to use standards in the design of the system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. The system will use high performance graphic workstations using an X-Windows Graphical User Interface at the operator interface level. It connects to VME-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

  4. Standards and the design of the Advanced Photon Source control system

    Science.gov (United States)

    McDowell, W. P.; Knott, M. J.; Lenkszus, F. R.; Kraimer, M. R.; Daly, R. T.; Arnold, N. D.; Anderson, M. D.; Anderson, J. B.; Zieman, R. C.; Cha, Ben-Chin K.

    The Advanced Photon Source (APS), now under construction at Argonne National Laboratory is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. In the conceptual stage the control system design group faced the challenges that face all control system designers: to force the machine designers to quantify and codify the system requirements, to protect the investment in hardware and software from rapid obsolescence, and to find methods of quickly incorporating new generations of equipment and replace of obsolete equipment without disrupting the exiting system. To solve these and related problems, the APS control system group made an early resolution to use standards in the design of the system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. The system will use high performance graphic workstations using an X-Windows Graphical User Interface at the operator interface level. It connects to VME-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities.

  5. Integral Sliding Mode Control Strategy of D-STATCOM for Unbalanced Load Compensation under Various Disturbances

    OpenAIRE

    Mingchao Xia; Yanhui Mao

    2013-01-01

    Control strategies of D-STATCOM for unbalanced load compensation under internal and external disturbances were discussed. Linear control strategies do not have a satisfactory dynamic performance and become invalid under internal or external disturbances. To guarantee a good precision and robustness, a control strategy combining input-output feedback linearization technique with integral sliding mode control (ISMC) method was applied to D-STATCOM for unbalanced load compensation. The strategy ...

  6. Advanced h∞ control towards nonsmooth theory and applications

    CERN Document Server

    Orlov, Yury V

    2014-01-01

    This compact monograph is focused on disturbance attenuation in nonsmooth dynamic systems, developing an H∞ approach in the nonsmooth setting. Similar to the standard nonlinear H∞ approach, the proposed nonsmooth design guarantees both the internal asymptotic stability of a nominal closed-loop system and the dissipativity inequality, which states that the size of an error signal is uniformly bounded with respect to the worst-case size of an external disturbance signal. This guarantee is achieved by constructing an energy or storage function that satisfies the dissipativity inequality and is then utilized as a Lyapunov function to ensure the internal stability requirements.    Advanced H∞ Control is unique in the literature for its treatment of disturbance attenuation in nonsmooth systems. It synthesizes various tools, including Hamilton–Jacobi–Isaacs partial differential inequalities as well as Linear Matrix Inequalities. Along with the finite-dimensional treatment, the synthesis is exten...

  7. Recent Advances in Understanding Integrative Control of Potassium Homeostasis

    Science.gov (United States)

    Youn, Jang H.; McDonough, Alicia A.

    2016-01-01

    The potassium homeostatic system is very tightly regulated. Recent studies have shed light on the sensing and molecular mechanisms responsible for this tight control. In addition to classic feedback regulation mediated by a rise in extracellular fluid (ECF) [K+], there is evidence for a feedforward mechanism: Dietary K+ intake is sensed in the gut, and an unidentified gut factor is activated to stimulate renal K+ excretion. This pathway may explain renal and extrarenal responses to altered K+ intake that occur independently of changes in ECF [K+]. Mechanisms for conserving ECF K+ during fasting or K+ deprivation have been described: Kidney NADPH oxidase activation initiates a cascade that provokes the retraction of K+ channels from the cell membrane, and muscle becomes resistant to insulin stimulation of cellular K+ uptake. How these mechanisms are triggered by K+ deprivation remains unclear. Cellular AMP kinase–dependent protein kinase activity provokes the acute transfer of K+ from the ECF to the ICF, which may be important in exercise or ischemia. These recent advances may shed light on the beneficial effects of a high-K+ diet for the cardiovascular system. PMID:18759636

  8. Advanced process control with design-based metrology

    Science.gov (United States)

    Yang, Hyunjo; Kim, Jungchan; Hong, Jongkyun; Yim, Donggyu; Kim, Jinwoong; Hasebe, Toshiaki; Yamamoto, Masahiro

    2007-03-01

    K1 factor for development and mass-production of memory devices has been decreased down to below 0.30 in recent years. Process technology has responded with extreme resolution enhancement technologies (RET) and much more complex OPC technologies than before. ArF immersion lithography is expected to remain the major patterning technology through under 35 nm node, where the degree of process difficulties and the sensitivity to process variations grow even higher. So, Design for manufacturing (DFM) is proposed to lower the degree of process difficulties and advanced process control (APC) is required to reduce the process variations. However, both DFM and APC need much feed-back from the wafer side such as hot spot inspection results and total CDU measurements at the lot, wafer, field and die level. In this work, we discuss a new design based metrology which can compare SEM image with CAD data and measure the whole CD deviations from the original layouts in a full die. It can provide the full information of hot spots and the whole CD distribution diagram of various transistors in peripheral regions as well as cell layout. So, it is possible to analyze the root cause of the CD distribution of some specific transistors or cell layout, such as OPC error, mask CDU, lens aberrations or etch process variation and so on. The applications of this new inspection tool will be introduced and APC using the analysis result will be presented in detail.

  9. 3. IFAC workshop: advances in automotive control. Vol. 1. Preprints

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    As the subject indicates, the aim of this workshop will be to discuss the latest advances related to motor vehicles, but also, and more generally, to exchange ideas between academic partners, car-manufacturers and subcontractors. The programme shows that a special effort has been made in this respect. No doubt plenary lectures are of great importance and the thematic sessions in the different sectors are the essence of such workshops; however, the discussions between experts in the different fields, the meetings between people from industry, universities and public or private laboratories, as well as the resulting exchange of ideas, are at least as important. Research is often criticized for providing merely theoretical results and for the insufficient number of its applications. But the motor vehicle offers a wide field of applications in which we can validate all techniques, tools and methods. This allows us to be involved in all the areas of fundamental research, in all the different possible approaches from fundamental research to technology transfer, and to observe the actual effects of our results. The increase in road traffic was a major problem of the past XXth century. It is clear that one the challenges of the XXIst century will be improve driving safety and comfort. The different work sessions concerning more control, driveline modelling, vehicle dynamics, electronic architecture, intelligent components, engine control, engine modelling, the modelling of combustion and turbocharging, diagnostics and subsystems. The quality of the papers and the diversity of their origins clearly shows the interest that we all take in this key sector of our research and industry. (orig.)

  10. Design of intelligent comfort control system with human learning and minimum power control strategies

    International Nuclear Information System (INIS)

    This paper presents the design of an intelligent comfort control system by combining the human learning and minimum power control strategies for the heating, ventilating and air conditioning (HVAC) system. In the system, the predicted mean vote (PMV) is adopted as the control objective to improve indoor comfort level by considering six comfort related variables, whilst a direct neural network controller is designed to overcome the nonlinear feature of the PMV calculation for better performance. To achieve the highest comfort level for the specific user, a human learning strategy is designed to tune the user's comfort zone, and then, a VAV and minimum power control strategy is proposed to minimize the energy consumption further. In order to validate the system design, a series of computer simulations are performed based on a derived HVAC and thermal space model. The simulation results confirm the design of the intelligent comfort control system. In comparison to the conventional temperature controller, this system can provide a higher comfort level and better system performance, so it has great potential for HVAC applications in the future

  11. [Economic contribution of gynecological and obstetrical ultrasound in an advanced strategy for the Zinguinchor region].

    Science.gov (United States)

    N'Diaye, P; Tal Dia, A; Fall, C; Diédhiou, A; Aris, F Badji

    2003-03-01

    Aiming to strengthen the accessibility of ultrasound technology to rural populations, an advanced strategy ultrasound programme was implemented in the health districts of Sedhiou, Oussouye, Bignona and Ziguinchor all located within Casamance in Senegal. Within the first year of activity (January 1, 2001-December 31, 2001), the team from the regional health centre (RHC) was dispatched 56 times. Ultrasound scans were performed in the homes of 1,273 patients among which 192 were referred to the RHC for specialised follow-up and treatment. The financial benefit for the RHC totaled 3,120,000 francs; 2,612,500 francs for the district hospital; and 3,561,300 francs for the population at large. The advanced strategy for performing ultrasound scans has therefore been economically profitable at the community level as much as at the level of health structures. Through supporting the activities of the district hospitals, the RHC contributed technical support and increased the potential, not solely for the treatment of disease but for the health services overall. The revenue generated has given managers a greater possibility to improve health care and services. The decentralisation programme and reduction in the cost have decreased the unsatisfied needs in ultrasound services by making the technology more financially and geographically accessible. Thus, by saving input costs in terms of time, transportation and capital, the practice of ultrasound scans in district hospitals has been strengthened and has improved the capacity to provide care and treat the population's health problems. The continuation of this programme is advantageous, but necessitates two complementary actions: enhancing of the technical level and capacity of the district hospitals with the installation of ultrasound technology and equipment, and raising the level of knowledge by training staff in administering ultrasound scans.

  12. The Robust Control Mixer Method for Reconfigurable Control Design By Using Model Matching Strategy

    DEFF Research Database (Denmark)

    Yang, Z.; Blanke, Mogens; Verhagen, M.

    2001-01-01

    This paper proposes a robust reconfigurable control synthesis method based on the combination of the control mixer method and robust H1 con- trol techniques through the model-matching strategy. The control mixer modules are extended from the conventional matrix-form into the LTI sys- tem form...... recovery besides the functionality recovery is also discussed under this framework. Comparing with the conventional control mixer method, the proposed method considers the recon gured system's stability, performance and robustness simultaneously. Finally, the proposed method is illustrated by a case study...

  13. Power Control Technique for Efficient Call Admission Control in Advanced Wirless Networks

    Directory of Open Access Journals (Sweden)

    Ch. Sreenivasa Rao

    2012-06-01

    Full Text Available In 4G networks, call admission control techniques have been proposed to provide Quality of Service (QoS in a network by restricting the access to network resources. Power control is essential in call admission control in order to provide fair access to all users, improve battery lifetime and system performance. But the existing call admission control algorithms rarely consider the power controlling techniques in the handoff process for different traffic classes. In this paper, we propose to develop a power controlled call admission control scheme for handoff in the advanced wireless networks. The incoming call measures the initial interference on it and then the base station starts transmitting the packets to the new call. The new call is rejected when the interference reaches a threshold value.Whenever an existing call meets the power constraint, the transmit power is decremented based on thetraffic class and incoming call obtains this information by monitoring the interference received on it. Theconvergence of the power control algorithm is checked and the power levels of all incoming calls areadjusted. From our simulation results we prove that this power control technique provides efficienthandoff in the 4G networks by increasing the throughput and reducing the delay of the existing users.

  14. Designing a hosting area as an advanced nursing care strategy in a pediatric nursing ward

    Directory of Open Access Journals (Sweden)

    Paola Pino A.

    2013-06-01

    Full Text Available Background: The most important comfort needs for caregivers are related to improving their hospital stay conditions, with more comfortable waiting rooms, a place to sleep, a toilette with shower, food and a safe place where to leave their belongings. Objective: To implement a hosting area that meets the comfort needs of parents who do not have their own accommodations during the hospitalization of their children. Methodology: Innovative strategies in providing advanced nursing care based on the theoretical model of Kolcaba, which allows us to bring the discipline of nursing care into practice, in direct benefit of patients. Results: We expect an increase in comfort perception of parents during hospitalization, which will lead to increased alertness of parents, effective participation in child care, improved response to educational interventions and effective linkages with the caring team. Conclusions: A hosting area for parents of hospitalized children, designed to meet the most important comfort needs reported in the literature and contextualized according to Kolcaba’s theory, can contribute to implement advanced nursing care, recovering the essence of nursing at the Pediatrics Service of the UC Hospital.

  15. Enhancing presentation skills for the advanced practice nurse: strategies for success.

    Science.gov (United States)

    Vollman, Kathleen M

    2005-01-01

    Professional speaking is a component of the professional practice role of the advanced practice nurse (APN). The skills to communicate effectively to one person or an audience of 100 provide the APN with the essential tools for implementing change, collaborating effectively, presenting information at professional meetings, or communicating the impact of clinical outcomes in the boardroom. Public speaking skills, a professional image, and improved communication can facilitate advancement along any career ladder. The greater your fear, the more self-confidence you will gain by stepping up to a challenge and conquering it. This article describes strategies for organizing and presenting your message in a clear and concise format. Techniques to manage the anxiety produced when attempting to articulate your thoughts is essential for effective communication. Skills for enhancing the delivery of your message through effective body language, professional image, voice modulation, and use of audiovisual aids are addressed. Creative techniques for fielding questions are key in promoting a dynamic closure and provide consistent reinforcement of the key message content. PMID:15714019

  16. Dental caries: Strategies to control this preventable disease

    Directory of Open Access Journals (Sweden)

    Andrew Rugg-Gunn

    2013-11-01

    Full Text Available Objective. To provide a brief commentary review of strategies to control dental caries. Dental decay is one of man’s most prevalent diseases. In many counties, severity increased in parallel with importation of sugar, reaching its zenith about 1950s and 1960s. Since then, severity has declined in many countries, due to the wide use of fluoride especially in toothpaste, but dental caries remains a disease of medical, social and economic importance. Within the EU in 2011, the cost of dental treatment was estimated to be €79 billion. The pathogenesis is well understood: bacteria in dental plaque (biofilm metabolise dietary sugars to acids which then dissolve dental enamel and dentine. Possible approaches to control caries development, therefore, involve: removal of plaque, reducing the acidogenic potential of plaque, reduction in sugar consumption, increasing the tooth’s resistance to acid attack, and coating the tooth surface to form a barrier between plaque and enamel. At the present time, only three approaches are of practical importance: sugar control, fluoride, and fissure sealing. The evidence that dietary sugars are the main cause of dental caries is extensive, and comes from six types of study. Without sugar, caries would be negligible. Fluoride acts in several ways to aid caries prevention. Ways of delivering fluoride can be classed as: ‘automatic’, ‘home care’ and ‘professional care’: the most important of these are discussed in detail in four articles in this issue of the Acta Medica Academica. Conclusion. Dental caries is preventable – individuals, communities and countries need strategies to achieve this.

  17. How Life Experience Shapes Cognitive Control Strategies: The Case of Air Traffic Control Training

    Science.gov (United States)

    Arbula, Sandra; Capizzi, Mariagrazia; Lombardo, Nicoletta; Vallesi, Antonino

    2016-01-01

    Although human flexible behavior relies on cognitive control, it would be implausible to assume that there is only one, general mode of cognitive control strategy adopted by all individuals. For instance, different reliance on proactive versus reactive control strategies could explain inter-individual variability. In particular, specific life experiences, like a highly demanding training for future Air Traffic Controllers (ATCs), could modulate cognitive control functions. A group of ATC trainees and a matched group of university students were tested longitudinally on task-switching and Stroop paradigms that allowed us to measure indices of cognitive control. The results showed that the ATCs, with respect to the control group, had substantially smaller mixing costs during long cue-target intervals (CTI) and a reduced Stroop interference effect. However, this advantage was present also prior to the training phase. Being more capable in managing multiple task sets and less distracted by interfering events suggests a more efficient selection and maintenance of task relevant information as an inherent characteristic of the ATC group, associated with proactive control. Critically, the training that the ATCs underwent improved their accuracy in general and reduced response time switching costs during short CTIs only. These results indicate a training-induced change in reactive control, which is described as a transient process in charge of stimulus-driven task detection and resolution. This experience-based enhancement of reactive control strategy denotes how cognitive control and executive functions in general can be shaped by real-life training and underlines the importance of experience in explaining inter-individual variability in cognitive functioning. PMID:27311017

  18. How Life Experience Shapes Cognitive Control Strategies: The Case of Air Traffic Control Training.

    Directory of Open Access Journals (Sweden)

    Sandra Arbula

    Full Text Available Although human flexible behavior relies on cognitive control, it would be implausible to assume that there is only one, general mode of cognitive control strategy adopted by all individuals. For instance, different reliance on proactive versus reactive control strategies could explain inter-individual variability. In particular, specific life experiences, like a highly demanding training for future Air Traffic Controllers (ATCs, could modulate cognitive control functions. A group of ATC trainees and a matched group of university students were tested longitudinally on task-switching and Stroop paradigms that allowed us to measure indices of cognitive control. The results showed that the ATCs, with respect to the control group, had substantially smaller mixing costs during long cue-target intervals (CTI and a reduced Stroop interference effect. However, this advantage was present also prior to the training phase. Being more capable in managing multiple task sets and less distracted by interfering events suggests a more efficient selection and maintenance of task relevant information as an inherent characteristic of the ATC group, associated with proactive control. Critically, the training that the ATCs underwent improved their accuracy in general and reduced response time switching costs during short CTIs only. These results indicate a training-induced change in reactive control, which is described as a transient process in charge of stimulus-driven task detection and resolution. This experience-based enhancement of reactive control strategy denotes how cognitive control and executive functions in general can be shaped by real-life training and underlines the importance of experience in explaining inter-individual variability in cognitive functioning.

  19. How Life Experience Shapes Cognitive Control Strategies: The Case of Air Traffic Control Training.

    Science.gov (United States)

    Arbula, Sandra; Capizzi, Mariagrazia; Lombardo, Nicoletta; Vallesi, Antonino

    2016-01-01

    Although human flexible behavior relies on cognitive control, it would be implausible to assume that there is only one, general mode of cognitive control strategy adopted by all individuals. For instance, different reliance on proactive versus reactive control strategies could explain inter-individual variability. In particular, specific life experiences, like a highly demanding training for future Air Traffic Controllers (ATCs), could modulate cognitive control functions. A group of ATC trainees and a matched group of university students were tested longitudinally on task-switching and Stroop paradigms that allowed us to measure indices of cognitive control. The results showed that the ATCs, with respect to the control group, had substantially smaller mixing costs during long cue-target intervals (CTI) and a reduced Stroop interference effect. However, this advantage was present also prior to the training phase. Being more capable in managing multiple task sets and less distracted by interfering events suggests a more efficient selection and maintenance of task relevant information as an inherent characteristic of the ATC group, associated with proactive control. Critically, the training that the ATCs underwent improved their accuracy in general and reduced response time switching costs during short CTIs only. These results indicate a training-induced change in reactive control, which is described as a transient process in charge of stimulus-driven task detection and resolution. This experience-based enhancement of reactive control strategy denotes how cognitive control and executive functions in general can be shaped by real-life training and underlines the importance of experience in explaining inter-individual variability in cognitive functioning. PMID:27311017

  20. Invited review: Stem cells and muscle diseases: advances in cell therapy strategies.

    Science.gov (United States)

    Negroni, Elisa; Gidaro, Teresa; Bigot, Anne; Butler-Browne, Gillian S; Mouly, Vincent; Trollet, Capucine

    2015-04-01

    Despite considerable progress to increase our understanding of muscle genetics, pathophysiology, molecular and cellular partners involved in muscular dystrophies and muscle ageing, there is still a crucial need for effective treatments to counteract muscle degeneration and muscle wasting in such conditions. This review focuses on cell-based therapy for muscle diseases. We give an overview of the different parameters that have to be taken into account in such a therapeutic strategy, including the influence of muscle ageing, cell proliferation and migration capacities, as well as the translation of preclinical results in rodent into human clinical approaches. We describe recent advances in different types of human myogenic stem cells, with a particular emphasis on myoblasts but also on other candidate cells described so far [CD133+ cells, aldehyde dehydrogenase-positive cells (ALDH+), muscle-derived stem cells (MuStem), embryonic stem cells (ES) and induced pluripotent stem cells (iPS)]. Finally, we provide an update of ongoing clinical trials using cell therapy strategies.

  1. Economic Analysis of HPAI Control in the Netherlands II: Comparison of Control Strategies

    NARCIS (Netherlands)

    Longworth, N.J.; Mourits, Monique C.M.; Saatkamp, H.W.

    2014-01-01

    A combined epidemiological-economic modelling approach was used to analyse strategies for highly pathogenic avian influenza (HPAI) control for the Netherlands. The modelling framework used was InterSpread Plus (ISP), a spatially based, stochastic and dynamic simulation model. A total of eight contro

  2. Advanced Stellar Compass - Adeos II - Interface Control Document

    DEFF Research Database (Denmark)

    Betto, Maurizio; Jørgensen, John Leif; Kilsgaard, Søren;

    This document describes the Advanced Stellar Compass (ASC) and defines the interfaces between the instrument and the ADEOS II satellite. The ASC is a highly advanced and autonomous Stellar Reference Unit designed, developed and produced by the Space Instrumentation Group of the Department...... are given and to conclude we review the ASC specifications against the ADEOS II requirements and provide the verification matrix....

  3. The environmental control and life support system advanced automation project

    Science.gov (United States)

    Dewberry, Brandon S.

    1991-01-01

    The objective of the ECLSS Advanced Automation project includes reduction of the risk associated with the integration of new, beneficial software techniques. Demonstrations of this software to baseline engineering and test personnel will show the benefits of these techniques. The advanced software will be integrated into ground testing and ground support facilities, familiarizing its usage by key personnel.

  4. Control Law Design for Twin Rotor MIMO System with Nonlinear Control Strategy

    Directory of Open Access Journals (Sweden)

    M. Ilyas

    2016-01-01

    Full Text Available Modeling of complex air vehicles is a challenging task due to high nonlinear behavior and significant coupling effect between rotors. Twin rotor multi-input multioutput system (TRMS is a laboratory setup designed for control experiments, which resembles a helicopter with unstable, nonlinear, and coupled dynamics. This paper focuses on the design and analysis of sliding mode control (SMC and backstepping controller for pitch and yaw angle control of main and tail rotor of the TRMS under parametric uncertainty. The proposed control strategy with SMC and backstepping achieves all mentioned limitations of TRMS. Result analysis of SMC and backstepping control schemes elucidates that backstepping provides efficient behavior with the parametric uncertainty for twin rotor system. Chattering and oscillating behaviors of SMC are removed with the backstepping control scheme considering the pitch and yaw angle for TRMS.

  5. Strengthening control over radioactive sources in authorized use and regaining control over orphan sources. National strategies

    International Nuclear Information System (INIS)

    The objective of this report is to provide practical guidance to States on the development of a national strategy for improving control over radioactive sources, particularly dangerous sources (Categories 1-3). Part of this process involves the determination of the magnitude of the potential problem with orphan and vulnerable sources and indeed, whether or not a national strategy is needed. The ultimate objective is that States will use this report to develop and then implement a plan of action that will result in all significant sources being managed in a safe and secure manner. This report attempts to provide both the background knowledge and the methodology necessary for an individual or small team of responsible persons to develop a national strategy for improving control over all radioactive sources, but especially orphan and vulnerable sources. The background knowledge given in Chapter 3 is an update of the information on practices that was given in IAEA-TECDOC-804, which focused on spent radioactive sources. After some introductory material, this report provides both the factual information and the general steps needed to develop and implement a national strategy. Part I contains background information for those who are not already familiar with the subject including the need for national strategies, the generic causes of loss of control of sources, with specific examples and the common applications of radioactive sources. Part II details the actual process for the development and implementation of a national strategy, which includes assessing the problem by first gathering specific and national information, determining the nature and magnitude of the problem, developing the national strategy by evaluating, and prioritizing possible solutions, implementing the strategy subsequent to a high level decision; and evaluating the effectiveness of the plan and making changes as a result until the desired objective is achieved. Searches for sources will be part of

  6. Advance Noise Control Fan II: Test Rig Fan Risk Management Study

    Science.gov (United States)

    Lucero, John

    2013-01-01

    Since 1995 the Advanced Noise Control Fan (ANCF) has significantly contributed to the advancement of the understanding of the physics of fan tonal noise generation. The 9'x15' WT has successfully tested multiple high speed fan designs over the last several decades. This advanced several tone noise reduction concepts to higher TRL and the validation of fan tone noise prediction codes.

  7. New advances in models and strategies for developing anti-obesity drugs

    Science.gov (United States)

    Kim, Gilbert W.; Lin, Jieru E.; Blomain, Erik S.; Waldman, Scott A.

    2014-01-01

    Introduction Obesity is a worldwide pandemic. Obesity-related health and economic costs are staggering. Existing strategies to combat obesity through lifestyle improvements and medical intervention have had limited success. Pharmacotherapy, in combination with lifestyle modification, may play a vital role in reversing the disease burden. However, past and current weight-loss medications have had serious safety risks, notably cardiovascular and psychiatric events. Areas covered We review the strategies for designing new anti-obesity drugs by describing those currently in development. We describe their target, mechanism of action, and developmental or regulatory status. We also discuss the problem of weight regain following weight loss, and its relevance to the long-term success of anti-obesity pharmacotherapy. Expert opinion For weight management drugs to achieve the safety and efficacy required to be impactful, current studies are uncovering and characterizing new targets, including new signaling circuits and hormones regulating appetite and metabolism, and re-evaluating the role of pharmacotherapy in weight management. To avoid the safety failures of many past weight-loss drugs, the models and strategies covered in this article incorporate recent advances in knowledge and technology. We discuss the emergence of cGMP signaling as a potentially transformative target in weight management. Modulating cGMP signaling may represent an ideal goal for an anti-obesity pharmacotherapy, reflecting some of the major themes described in the present review: targeting pathways that are newly realized as relevant for weight management; promoting safety by re-purposing drugs that are safe, proven, and approved for clinical use; and having a synergistic effect on multiple, reinforcing pathways. PMID:23621300

  8. Steam generator degradation: Current mitigation strategies for controlling corrosion

    International Nuclear Information System (INIS)

    Steam Generator degradation has caused substantial losses of power generation, resulted in large repair and maintenance costs, and contributed to significant personnel radiation exposures in Pressurized Water Reactors (PWRs) operating throughout the world. EPRI has just published the revised Steam Generator Reference Book, which reviews all of the major forms of SG degradation. This paper discusses the types of SG degradation that have been experienced with emphasis on the mitigation strategies that have been developed and implemented in the field. SG degradation is presented from a world wide perspective as all countries operating PWRs have been effected to one degree or another. The paper is written from a US. perspective where the utility industry is currently undergoing tremendous change as a result of deregulation of the electricity marketplace. Competitive pressures are causing utilities to strive to reduce Operations and Maintenance (O ampersand M) and capital costs. SG corrosion is a major contributor to the O ampersand M costs of PWR plants, and therefore US utilities are evaluating and implementing the most cost effective solutions to their corrosion problems. Mitigation strategies developed over the past few years reflect a trend towards plant specific solutions to SG corrosion problems. Since SG degradation is in most cases an economic problem and not a safety problem, utilities can focus their mitigation strategies on their unique financial situation. Accordingly, the focus of R ampersand D has shifted from the development of more expensive, prescriptive solutions (e.g. reduced impurity limits) to corrosion problems to providing the utilities with a number of cost effective mitigation options (e.g. molar ratio control, boric acid treatment)

  9. Steam generator degradation: Current mitigation strategies for controlling corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Millett, P. [Electric Power Research Institute, Palo Alto, CA (United States)

    1997-02-01

    Steam Generator degradation has caused substantial losses of power generation, resulted in large repair and maintenance costs, and contributed to significant personnel radiation exposures in Pressurized Water Reactors (PWRs) operating throughout the world. EPRI has just published the revised Steam Generator Reference Book, which reviews all of the major forms of SG degradation. This paper discusses the types of SG degradation that have been experienced with emphasis on the mitigation strategies that have been developed and implemented in the field. SG degradation is presented from a world wide perspective as all countries operating PWRs have been effected to one degree or another. The paper is written from a US. perspective where the utility industry is currently undergoing tremendous change as a result of deregulation of the electricity marketplace. Competitive pressures are causing utilities to strive to reduce Operations and Maintenance (O&M) and capital costs. SG corrosion is a major contributor to the O&M costs of PWR plants, and therefore US utilities are evaluating and implementing the most cost effective solutions to their corrosion problems. Mitigation strategies developed over the past few years reflect a trend towards plant specific solutions to SG corrosion problems. Since SG degradation is in most cases an economic problem and not a safety problem, utilities can focus their mitigation strategies on their unique financial situation. Accordingly, the focus of R&D has shifted from the development of more expensive, prescriptive solutions (e.g. reduced impurity limits) to corrosion problems to providing the utilities with a number of cost effective mitigation options (e.g. molar ratio control, boric acid treatment).

  10. FAB (Functionally Alert Behavior Strategies) to Improve Self-Control

    Science.gov (United States)

    Pagano, John

    2015-01-01

    This paper describes the FAB (Functionally Alert Behavior) Strategies approach to improve behavior in children and adolescents with complex behavioral challenges. FAB Strategies include evidence-based environmental adaptations, sensory modulation, positive behavioral support, and physical self-regulation strategies. FAB Strategies can be used by…

  11. Migration control: a distance compensation strategy in ants.

    Science.gov (United States)

    O'Shea-Wheller, Thomas A; Sendova-Franks, Ana B; Franks, Nigel R

    2016-08-01

    Migratory behaviour forms an intrinsic part of the life histories of many organisms but is often a high-risk process. Consequently, varied strategies have evolved to negate such risks, but empirical data relating to their functioning are limited. In this study, we use the model system of the house-hunting ant Temnothorax albipennis to demonstrate a key strategy that can shorten migration exposure times in a group of social insects. Colonies of these ants frequently migrate to new nest sites, and due to the nature of their habitat, the distances over which they do so are variable, leading to fluctuating potential costs dependent on migration parameters. We show that colonies of this species facultatively alter the dynamics of a migration and so compensate for the distance over which a given migration occurs. Specifically, they achieve this by modulating the rate of 'tandem running', in which workers teach each other the route to a new nest site. Using this method, colonies are able to engage a larger number of individuals in the migration process when the distance to be traversed is greater, and furthermore, the system appears to be based on perceived encounter rate at the individual level. This form of decentralised control highlights the adaptive nature of a behaviour of ecological importance, and indicates that the key to its robustness lies in the use of simple rules. Additionally, our results suggest that such coordinated group reactions are central to achieving the high levels of ecological success seen in many eusocial organisms.

  12. Workplace strategies for the control of work-related risks.

    Science.gov (United States)

    Kogi, K

    1993-10-01

    The prevention of work-related diseases and disorders, including those of neuropsychobehavioral nature, calls for integrated action to improve both job content and the working environment. Recent international labor standards have highlighted the importance of a good safety and health management system that ensures the assessment of risks and the appropriate control of these risks. Internationally, programs to cope with work-related risks place an increasing emphasis on participatory management of preventive measures, practical methods of risk assessment, and immediate improvements with the support of action-oriented training and information. Psychosocial factors, work performance, and job content need special attention. Workplace strategies must be developed by active participation of employers and workers, with their informed consent. These strategies and linked training activities should build on local practice and achievements rather than administrative models and be geared to the real local needs. In coping with the neurobehavioral effects, international sharing of positive experiences is useful especially with respect to: (i) providing information on potential neurobehavioral effects including labeling, safety datasheets, and precautions; (ii) providing practical advice about locally achieved improvements; (iii) providing action-oriented training; and (iv) creating opportunities for participatory workplace improvements.

  13. Migration control: a distance compensation strategy in ants.

    Science.gov (United States)

    O'Shea-Wheller, Thomas A; Sendova-Franks, Ana B; Franks, Nigel R

    2016-08-01

    Migratory behaviour forms an intrinsic part of the life histories of many organisms but is often a high-risk process. Consequently, varied strategies have evolved to negate such risks, but empirical data relating to their functioning are limited. In this study, we use the model system of the house-hunting ant Temnothorax albipennis to demonstrate a key strategy that can shorten migration exposure times in a group of social insects. Colonies of these ants frequently migrate to new nest sites, and due to the nature of their habitat, the distances over which they do so are variable, leading to fluctuating potential costs dependent on migration parameters. We show that colonies of this species facultatively alter the dynamics of a migration and so compensate for the distance over which a given migration occurs. Specifically, they achieve this by modulating the rate of 'tandem running', in which workers teach each other the route to a new nest site. Using this method, colonies are able to engage a larger number of individuals in the migration process when the distance to be traversed is greater, and furthermore, the system appears to be based on perceived encounter rate at the individual level. This form of decentralised control highlights the adaptive nature of a behaviour of ecological importance, and indicates that the key to its robustness lies in the use of simple rules. Additionally, our results suggest that such coordinated group reactions are central to achieving the high levels of ecological success seen in many eusocial organisms. PMID:27430995

  14. Controlled Immobilization Strategies to Probe Short Hyaluronan-Protein Interactions

    Science.gov (United States)

    Minsky, Burcu Baykal; Antoni, Christiane H.; Boehm, Heike

    2016-02-01

    Well-controlled grafting of small hyaluronan oligosaccharides (sHA) enables novel approaches to investigate biological processes such as angiogenesis, immune reactions and cancer metastasis. We develop two strategies for covalent attachment of sHA, a fast high-density adsorption and a two-layer system that allows tuning the density and mode of immobilization. We monitored the sHA adlayer formation and subsequent macromolecular interactions by label-free quartz crystal microbalance with dissipation (QCM-D). The modified surfaces are inert to unspecific protein adsorption, and yet retain the specific binding capacity of sHA. Thus they are an ideal tool to study the interactions of hyaluronan-binding proteins and short hyaluronan molecules as demonstrated by the specific recognition of LYVE-1 and aggrecan. Both hyaladherins recognize sHA and the binding is independent to the presence of the reducing end.

  15. Controlled Immobilization Strategies to Probe Short Hyaluronan-Protein Interactions

    Science.gov (United States)

    Minsky, Burcu Baykal; Antoni, Christiane H.; Boehm, Heike

    2016-01-01

    Well-controlled grafting of small hyaluronan oligosaccharides (sHA) enables novel approaches to investigate biological processes such as angiogenesis, immune reactions and cancer metastasis. We develop two strategies for covalent attachment of sHA, a fast high-density adsorption and a two-layer system that allows tuning the density and mode of immobilization. We monitored the sHA adlayer formation and subsequent macromolecular interactions by label-free quartz crystal microbalance with dissipation (QCM-D). The modified surfaces are inert to unspecific protein adsorption, and yet retain the specific binding capacity of sHA. Thus they are an ideal tool to study the interactions of hyaluronan-binding proteins and short hyaluronan molecules as demonstrated by the specific recognition of LYVE-1 and aggrecan. Both hyaladherins recognize sHA and the binding is independent to the presence of the reducing end. PMID:26883791

  16. Aedes aegypti Control Strategies in Brazil: Incorporation of New Technologies to Overcome the Persistence of Dengue Epidemics

    Directory of Open Access Journals (Sweden)

    Helena R. C. Araújo

    2015-06-01

    Full Text Available Dengue is considered to be the most important mosquito-borne viral disease in the world. The Aedes aegypti mosquito, its vector, is highly anthropophilic and is very well adapted to urban environments. Although several vaccine candidates are in advanced stages of development no licensed dengue vaccine is yet available. As a result, controlling the spread of dengue still requires that mosquitoes be targeted directly. We review the current methods of dengue vector control focusing on recent technical advances. We first examine the history of Brazil’s National Dengue Control Plan in effect since 2002, and we describe its establishment and operation. With the persistent recurrence of dengue epidemics, current strategies should be reassessed to bring to the forefront a discussion of the possible implementation of new technologies in Brazil’s mosquito control program.

  17. Aedes aegypti Control Strategies in Brazil: Incorporation of New Technologies to Overcome the Persistence of Dengue Epidemics.

    Science.gov (United States)

    Araújo, Helena R C; Carvalho, Danilo O; Ioshino, Rafaella S; Costa-da-Silva, André L; Capurro, Margareth L

    2015-01-01

    Dengue is considered to be the most important mosquito-borne viral disease in the world. The Aedes aegypti mosquito, its vector, is highly anthropophilic and is very well adapted to urban environments. Although several vaccine candidates are in advanced stages of development no licensed dengue vaccine is yet available. As a result, controlling the spread of dengue still requires that mosquitoes be targeted directly. We review the current methods of dengue vector control focusing on recent technical advances. We first examine the history of Brazil's National Dengue Control Plan in effect since 2002, and we describe its establishment and operation. With the persistent recurrence of dengue epidemics, current strategies should be reassessed to bring to the forefront a discussion of the possible implementation of new technologies in Brazil's mosquito control program. PMID:26463204

  18. Control strategies and experimental verifications of the electromagnetic mass damper system for structural vibration control

    Institute of Scientific and Technical Information of China (English)

    Zhang Chunwei; Ou Jinping

    2008-01-01

    The electromagnetic mass damper (EMD) control system, as an innovative active control system to reducestructural vibration, offers many advantages over traditional active mass driver/damper (AMD) control systems. In this paper,studies of several EMD control strategies and bench-scale shaking table tests of a two-story model structure are described.First, two structural models corresponding to uncontrolled and Zeroed cases are developed, and parameters of these modelsare validated through sinusoidal sweep tests to provide a basis for establishing an accurate mathematical model for furtherstudies. Then, a simplified control strategy for the EMD system based on the pole assignment control algorithm is proposed.Moreover, ideal pole locations are derived and validated through a series of shaking table tests. Finally, three benchmarkearthquake ground motions and sinusoidal sweep waves are imposed onto the structure to investigate the effectiveness andfeasibility of using this type of innovative active control system for structural vibration control. In addition, the robustnessof the EMD system is examined. The test results show that the EMD system is an effective and robust system for the controlof structural vibrations.

  19. THE ROLE OF STRATEGY IN ACHIEVING PERFORMANCE AND INTERNATIONAL RECOGNITION – THE CASE OF ROMANIAN ADVANCED RESEARCH UNIVERSITIES

    OpenAIRE

    Ruxandra CIULU; Olesia MIHAI

    2012-01-01

    The paper addresses the issue of strategy in higher education, applied to a group of top Romanian public universities. After reviewing the concepts of strategy (and its related sub-concepts), performance and internationalization, the authors briefly analyze the websites of the twelve Romanian universities included in the category ‘advanced research and education’. The study assesses the chances of Romanian universities to be included in the category of ‘top universities worldwide’ and conclu...

  20. Microgrids: Hierarchical Control and an Overview of the Control and Reserve Management Strategies

    DEFF Research Database (Denmark)

    Vandoorn, T.L.; Vasquez, Juan Carlos; de Kooning, D.M.;

    2013-01-01

    in the network, allowing the DG units to actively contribute in the frequency and voltage regulation. Microgrids can provide such coordination by aggregating DG, (controllable) loads and storage in small-scale networks, that can operate both in grid-connected and islanded mode. Here, the islanded operating...... condition is considered. Analogous as in the conventional networks, a hierarchical control structure can be implemented in islanded microgrids. In recent years, many different concepts for primary, secondary and tertiary control of microgrids have been investigated. These controllers can be classified...... as either local or centralized. In this article, the hierarchical control for application in microgrids is discussed and an overview of the control strategies is given with respect to the reserve provision by the DG units, loads and storage equipment....